BWR Steam Dryer Alternating Stress Assessment Procedures

Energy Technology Data Exchange (ETDEWEB)

Morante, R. J. [Brookhaven National Lab. (BNL), Upton, NY (United States); Hambric, S. A. [Brookhaven National Lab. (BNL), Upton, NY (United States); Ziada, S. [Brookhaven National Lab. (BNL), Upton, NY (United States)

2016-12-01

This report presents an overview of Boiling Water Reactor (BWR) steam dryer design; the fatigue cracking failures that occurred at the Quad Cities (QC) plants and their root causes; a history of BWR Extended Power Uprates (EPUs) in the USA; and a discussion of steam dryer modifications/replacements, alternating stress mechanisms on steam dryers, and structural integrity evaluations (static and alternating stress).

Investigation of the drying airflow at a newly developed dryer geometry for mixed flow grain dryers

Directory of Open Access Journals (Sweden)

Holger Scaar

2016-06-01

Full Text Available The mixed-flow dryer has been a matter of investigation many times regarding drying efficiency, dryer control, and performance enhancement over the past years. However, there is still considerable demand for optimization in terms of energy efficiency and homogeneity of drying. In order to analyze the specific energy consumption and the homogeneity of the drying process, different thermodynamic process conditions have been investigated for the conventional MFD design using numerical and experimental methods. Based on the results obtained, a novel dryer design has been developed. With this, a considerable increase of efficiency is expected. As the fluid dynamic analysis of the first design draft revealed, further development is required until scaling-up and transfer into practice will be possible. While homogeneous airflow conditions could be demonstrated in the core flow region in the center of the dryer, the configuration must be optimized in the near wall regions.

GAS DRYER DESIGN FOR VERMICELLI USING MICROCONTROLLER ATMEGA 8535

Directory of Open Access Journals (Sweden)

Akhmad Mufasil

2013-04-01

Full Text Available The purpose of this research is designing a gas dryer for vermicelli using a microcontroller ATmega 8535 that can overcome the obstacles in the drying department. The microcontroller ATmega 8535 used to regulate the temperature of the drying chamber. This tool design is made to compare between conventional dryer and a theoritical gas dryer in the factory. The method used in this paper is field study in the factory. Based on the experience then theoritical gas dryer design from the factory’s datas. A microcontroller Atmega 8535 is added to the dryer to easier the dryer operation. The result of the theoritical gas dryer design for vermicelli using a microcontroller ATmega 8535, showed a faster time drying for 131,04 kg of vermicelli need 47,72 minutes at a temperature of 40- 55° C.

Heat pump dryers theory, design and industrial applications

CERN Document Server

Alves-Filho, Odilio

2015-01-01

Explore the Social, Technological, and Economic Impact of Heat Pump Drying Heat pump drying is a green technology that aligns with current energy, quality, and environmental concerns, and when compared to conventional drying, delivers similar quality at a lower cost. Heat Pump Dryers: Theory, Design and Industrial Applications details the progression of heat pump drying-from pioneering research and demonstration work to an applied technology-and establishes principles and theories that can aid in the successful design and application of heat pump dryers. Based on the author's personal experience, this book compares heat pump dryers and conventional dryers in terms of performance, quality, removal rate, energy utilization, and the environmental effect of both drying processes. It includes detailed descriptions and layouts of heat pump dryers, outlines the principles of operation, and explains the equations, diagrams, and procedures used to form the basis for heat pump dryer dimensioning and design. The author ...

Heat transfer and energy efficiency in infrared paper dryers

Energy Technology Data Exchange (ETDEWEB)

Pettersson, Magnus

1999-11-01

Infrared (IR) dryers are widely used in the paper industry, mainly in the production of coated paper grades. The thesis deals with various aspects of heat transfer and energy use in infrared heaters and dryers as employed in the paper industry. Both gas-fired and electric IR dryers are considered and compared. The thesis also provides an introduction to infrared heaters and infrared drying, including a review of recent literature in the field. The transport of thermal radiation inside a paper sheet was investigated and different IR dryers were compared in terms of their ability to transfer energy to the internal parts of a paper sheet. Although there were evident differences in the absorption of radiation between gas-fired and electric IR dryers, the distinction was found not to be as important as has generally been believed. The main differences appeared to be due to the choice of a one- or a two-sided dryer solution, rather than the spectral distributions emitted by the dryers. A method for evaluating the radiation efficiency of IR heaters was proposed. An electric IR heater was evaluated in the laboratory. The radiation efficiency of the heater was shown to be strongly dependent on the power level. The maximum efficiency, found at high power level, was close to 60 %. A procedure for evaluation of the total energy transfer efficiency of an infrared paper dryer was proposed and used in the evaluation of an electric IR dryer operating in an industrial coating machine. The efficiency of the dryer was roughly 40 %. A model for an electric IR heater was developed. The model includes non-grey radiative heat transfer between the different parts of the heater, as well as conduction in reflector material and convective cooling of the surfaces. Using IR module voltage as the only input, model predictions of temperatures and heat flux were found to agree well with experimental data both at steady state and under transient conditions. The model was also extended to include

Design and testing of solar dryers for processing food wastes

Energy Technology Data Exchange (ETDEWEB)

Nijmeh, M.N.; Ragab, A.S.; Emeish, M.S. [University of Jordan, Amman (Jordan). Mechanical Engineering Dept.; Jubran, B.A. [International Islamic University of Malaysia, Kaula Lumpur (Malaysia). Dept. of Mechanical Engineering

1998-12-01

This paper investigates the potential of using two solar dryers manufactured from locally available materials under Jordanian climatic conditions for drying food wastes for utilization as animal feed. The first dryer is a radiative-convective type, while the second is a solar boiler dryer. Tests were also conducted to investigate the nutritious values of the dried products and their suitability as animal feed. It was found from tests that the solar boiler dryer is more efficient than the radiative-convective dryer for producing animal feed in terms of both quality and quantity. The nutritious values of the end products from the dryers were found to be within the international recommended values used for feeding chickens. (author)

Operation experiences of biofuel dryers; Drifterfarenheter fraan aangtorkar och direkta roekgastorkar

Energy Technology Data Exchange (ETDEWEB)

Berge, Christian; Dejfors, Charlotte [AaF Energikonsult Stockholm AB (Sweden)

2000-01-01

A study regarding operation experiences of indirect steam dryers and direct flue gas dryers of biofuels has been conducted. In the study, plants with the two types of dryers have been visited and operational experiences have been gathered and analysed. Results show that the well proven technique with flue gas dryers has a higher availability than the steam dryers. Several plants have problem with the feeding and discharge systems. Material selection is very important to prevent corrosion. Indirect steam dryers have more environmental regulations than flue gas dryers because of the generated condensate from the fuel drying process. Future work should concentrate on material selections, refining the feeding and discharge systems and control system.

Evaluation of a dryer in a steam generator

International Nuclear Information System (INIS)

Xue Yunkui; Liu Shixun; Guandao, Xie; Chen Junliang

1998-01-01

The hooked-vane-type dryer is used in vertical, natural circulation steam generators used in PWR-type nuclear power stations. it separates the fine droplets of water carried by steam so that the steam generator outlet steam moisture is below 0.25%. Such low moisture is demanded to ensure a safe and economic operation of the unit. The dryer is composed of hooked vanes and a draining structure. A series of tests to screen different designs were performed using air-water mixture. The paper presents the results of the investigation of the effect of the number of drainage hooks , the bending angle , distance between two adjacent vanes, and other geometrical parameters on the performance of a hooked-vane-type steam dryer. It indicates that the dryer still works effectively when the moisture of the steam at the dryer inlet changes in a wide range, and that the performance of the dryer is closely related to the geometry of the draining structure . On the basis of the results of this program, a draining structure with an original design was selected and it is presented in the paper. The performance of the selected draining structure is better than that of similar structures in China and abroad. (author)

Rotary drum dryers for coal slurries

Energy Technology Data Exchange (ETDEWEB)

Baunack, F

1983-04-01

The suitability, sizing and internal equipment of rotary drum dryers for high-ash coal slurries are discussed. Rotary dryers will handle also difficult slurries; by suitable drum sizes, lifter blades and chains not only high specific evaporation capacities can be achieved but also very high throughputs of up to 400 tons/h of finished product and high evaporation capacities of 60 tons/h.

Affordable Hybrid Heat Pump Clothes Dryer

Energy Technology Data Exchange (ETDEWEB)

TeGrotenhuis, Ward E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Butterfield, Andrew [Jabil, St. Petersburg, FL (United States); Caldwell, Dustin D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Crook, Alexander [Jabil, St. Petersburg, FL (United States)

2016-06-30

This project was successful in demonstrating the feasibility of a step change in residential clothes dryer energy efficiency by demonstrating heat pump technology capable of 50% energy savings over conventional standard-size electric dryers with comparable drying times. A prototype system was designed from off-the-shelf components that can meet the project’s efficiency goals and are affordable. An experimental prototype system was built based on the design that reached 50% energy savings. Improvements have been identified that will reduce drying times of over 60 minutes to reach the goal of 40 minutes. Nevertheless, the prototype represents a step change in efficiency over heat pump dryers recently introduced to the U.S. market, with 30% improvement in energy efficiency at comparable drying times.

CFD analysis for greenhouse effect solar dryer

International Nuclear Information System (INIS)

Wulandani, D.; Abdullah, K.; Hartulistiyoso, E.; Siswantara, I.

2006-01-01

Greenhouse Effect (GHE) solar dryer is a transparent wall structure, consists of absorber plate as solar heat collector, product holders (tray or batch) and fans to discharge moisture from the product. GHE solar dryer is one of the alternative dryer for the farmer and merchants to improve the quality of dried products. Direct sun drying is still popular choice by farmers because it is cheap and simple. However, the method is greatly dependent on the existence of solar irradiation and the product is contaminated very easily by pollution and dirt. The general constraint in designing artificial dryer is the problem of non-uniformity of final moisture content of product, especially for the cabinet of rack type dryer. This condition can be solved by providing uniform distribution of temperature, relative humidity (RH) and airflow velocity of the drying air. Therefore, in this study, such problem was approached by conducting flow simulation within the drying structure by using computational fluid dynamics (CFD) technology to determine the proper position of drying air inlet and outlet, location and capacity of the heat exchanger unit, the position and the capacity of the fan, to produce uniform distribution of the drying air temperature, RH and airflow velocity within the drying chamber.(Author)

Performance of modified greenhouse dryer with thermal energy storage

Directory of Open Access Journals (Sweden)

Om Prakash

2016-11-01

Full Text Available In this attempt, the main goal is to do annual performance, environomical analysis, energy analysis and exergy analysis of the modified greenhouse dryer (MGD operating under active mode (AM and passive mode (PM. Thermal storage is being applied on the ground of MGD. It is applied in three different ways namely barren floor, floor covered with black PVC sheet (PVC and Black Coated. Experimental study of dryers in no-load conditions reveals that floor covered with a black PVC sheet is more conducive for drying purpose than other floors. The MGD under AM is found to be more effective as compared to PM for tomato and capsicum, which are high moisture content crops. For medium moisture content crop (potato chips, both dryers show relatively similar drying performance. Crops dried inside the greenhouse dryer are found to be more nutrient than open sun dried crops. The payback period of the modified greenhouse dryer under passive mode is found to be 1.11 years. However, for the active mode of the modified greenhouse dryer is only 1.89 years. The embodied energy of the passive mode of the dryer is a 480.277 kWh and 628.73 kWh for the active mode of the dryer. The CO2 emissions per annum for passive and active mode greenhouse dryers are found to be 13.45 kg and 17.6 kg respectively. The energy payback time, carbon mitigation and carbon credit have been calculated based type of crop dried. The range of exergy efficiency is 29%–86% in MGD under PM and 30%–78% in the MGD under AM. The variation of Heat utilization factor (HUF for MGD under PM is 0.12–0.38 and 0.26–0.53 for MGD under AM. The range of co-efficient of performances (COP for MGD under PM is 0.55–0.87 and 0.58–0.73 for MGD under AM.

Experimental investigations of a chimney-dependent solar crop dryer

Energy Technology Data Exchange (ETDEWEB)

Afriyie, J.K.; Nazha, M.A.A.; Rajakaruna, H. [School of Engineering and Technology, De Montfort University, Queens Building, The Gateway, Leicester LE1 9BH (United Kingdom); Forson, F.K. [Department of Mechanical Engineering, Kwame Nkrumah University of Science and Technology, Kumasi (Ghana)

2009-01-15

An experimental investigation into the performance of a solar crop dryer with solar chimney and no air preheating is described. Tests were first performed on the cabinet dryer, using a normal chimney. The trials were repeated with a solar chimney. Still with the solar chimney, further trials were carried out with the roof of the drying chamber inclined further to form a tent dryer. The described tests include no-load tests for airflow rate measurements and drying tests, with cassava as the crop. Air velocities, temperatures, ambient relative humidity and the drop in crop moisture contents at different stages of the drying process are also presented. The effects of the various configurations described above on the drying process are deduced and discussed while comparing the experimental results with one another. In addition, the performance of the dryer in relation to other natural convection dryers is discussed. The results show that the solar chimney can increase the airflow rate of a direct-mode dryer especially when it is well designed with the appropriate angle of drying-chamber roof. However, the increase in flow rate only increases the drying rate when the relative humidity (RH) of the ambient air is below a certain mark (60% for cassava). (author)

Silk cocoon drying in forced convection type solar dryer

International Nuclear Information System (INIS)

Singh, Panna Lal

2011-01-01

The thin layer silk cocoon drying was studied in a forced convection type solar dryer. The drying chamber was provided with several trays on which the cocoons loaded in thin layer. The hot air generated in the solar air heater was forced into drying chamber to avoid the direct exposure of sunlight and UV radiation on cocoons. The drying air temperature varied from 50 to 75 o C. The cocoon was dried from the initial moisture content of about 60-12% (wb). The drying data was fitted to thin layer drying models. Drying behaviour of the silk cocoon was best fitted with the Wang and Singh drying model. Good agreement was obtained between predicted and experimental values. Quality of the cocoons dried in the solar dryer was at par with the cocoons dried in the conventional electrical oven dryer in term of the silk yield and strength of the silk. Saving of electrical energy was about 0.75 kWh/kg cocoons dried. Economic analysis indicated that the NPV of the solar dryer was higher and more stable (against escalation rate of electricity) as compare to the same for electrical oven dryer. Due to simplicity in design and construction and significant saving of operational electrical energy, solar cocoon dryer seems to be a viable option.

Development of an Active Solar Crop Dryer: Design Analysis and Performance Evaluation

International Nuclear Information System (INIS)

Itodo, I. N.; Adewole, A.M.; Edemaku, S.K.

2002-01-01

A forced convection indirect solar dryer powered by a PVC module was designed and evaluated. The performance of the dryer was poor; its drying rate, collector and system drying efficiency were 0.74 kg/day, 12% and 10% respectively. The dryer was redesigned and modified into a direct forced convection type- Its design analysis and performance evaluation was undertaken by drying mashed cassava. The drying rate, system drying collector and pick-up efficiencies were 1,6 kg/day (14%/day), 9%, 46% and 29% respectively. Comparatively, the drying rate for sun drying was 0.9 kg/day. The collector efficiency compared very well to the designed value of 48% and may not need further improvement. The pick-up efficiency also compared well with typical averages for this dryer type. The drying rate and system drying efficiency Indicate the need for further development of this dryer. Prediction equations were developed from the results of measured differences in collector, dryer and ambient air temperatures plotted on graphs and applying regression. It is recommended that the volumetric air-flow rate across the drying unit should he improved by affecting the tan speed and air inlet area of the dryer. The improved dryer will subsequently be compared to a natural convection dryer so that an appropriate dryer technology can be recommended for the rural small-scale farmers

Design and performance evaluation of a new hybrid solar dryer for banana

International Nuclear Information System (INIS)

Amer, B.M.A.; Hossain, M.A.; Gottschalk, K.

2010-01-01

A hybrid solar dryer was designed and constructed using direct solar energy and a heat exchanger. The dryer consists of solar collector, reflector, heat exchanger cum heat storage unit and drying chamber. The drying chamber was located under the collector. The dryer was operated during normal sunny days as a solar dryer, and during cloudy day as a hybrid solar dryer. Drying was also carried out at night with stored heat energy in water which was collected during the time of sun-shine and with electric heaters located at water tank. The efficiency of the solar dryer was raised by recycling about 65% of the drying air in the solar dryer and exhausting a small amount of it outside the dryer. Under Mid-European summer conditions it can raise up the air temperature from 30 to 40 deg. C above the ambient temperature. The solar dryer was tested for drying of ripe banana slices. The capacity of the dryer was to dry about 30 kg of banana slices in 8 h in sunny day from an initial moisture content of 82% to the final moisture content of 18% (wb). In the same time it reduced to only 62% (wb) moisture content in open sun drying method. The colour, aroma and texture of the solar dried products were better than the sun drying products.

Assessment of the bacterial contamination of hand air dryer in washrooms.

Science.gov (United States)

Alharbi, Sulaiman Ali; Salmen, Saleh Hussein; Chinnathambi, Arunachalam; Alharbi, Naiyf S; Zayed, M E; Al-Johny, Bassam O; Wainwright, Milton

2016-03-01

The present study was carried out, using standard techniques, to identify and count the bacterial contamination of hand air dryers, used in washrooms. Bacteria were isolated from the air flow, outlet nozzle of warm air dryers in fifteen air dryers used in these washrooms. Bacteria were found to be relatively numerous in the air flows. Bacterially contaminated air was found to be emitted whenever a warm air dryer was running, even when not being used for hand drying. Our investigation shows that Staphylococcus haemolyticus, Micrococcus luteus, Pseudomonas alcaligenes, Bacillus cereus and Brevundimonad diminuta/vesicularis were emitted from all of the dryers sampled, with 95% showing evidence of the presence of the potential pathogen S. haemolyticus. It is concluded that hot air dryers can deposit pathogenic bacteria onto the hands and body of users. Bacteria are distributed into the general environment whenever dryers are running and could be inhaled by users and none-users alike. The results provide an evidence base for the development and enhancement of hygienic hand drying practices.

Sustainability assessment of heat exchanger units for spray dryers

International Nuclear Information System (INIS)

Caglayan, Hasan; Caliskan, Hakan

2017-01-01

In this study, the sustainability assessment is performed to the system known as heat exchanger unit with spray dryer. The five-different dead state temperatures (0-5-10-15-20 °C) are considered. It is found that the heat exchanger has the highest energy efficiency (63.32%), while the overall system has the lowest one (5.56%). So, the combination of the spray dryer with the heat exchanger is more effective. On the other hand, the overall exergy efficiency of the system is lower than the heat exchanger and spray dryer for all of the dead state (environmental) temperatures. The exergy efficiency of the heat exchanger is inversely proportional to the dead state temperature, and the maximum rate is found as 49.65% at 0 °C. Furthermore, the exergy efficiencies of the spray dryer and overall system are directly proportional to the dead state temperatures, and the corresponding maximum rates are found to be 26.41% and 24.32% at 20 °C, respectively. Also, the exergy destruction is directly proportional to the dead state temperatures. The minimum and maximum exergy destruction rates are found at the dead state temperatures of 0 °C and 20 °C, respectively. Furthermore, the most sustainable system is found as the heat exchanger unit. - Highlights: • Thermodynamic analyses of industrial heat exchangers and spray dryers. • Sustainability of heat exchangers for spray dryers. • Dead state temperature effects on exergy efficiencies of heat exchangers and spray dryers.

The Instituto Nacional de Pesquisas da Amazonia-INPA solar dryer: an economical alternative for wood drying; O secador solar do INPA: uma alternativa economica para secar madeira

Energy Technology Data Exchange (ETDEWEB)

Moraes-Duzat, Rejane; Barbosa, Ana Paula; Vetter, Roland [Instituto Nacional de Pesquisas da Amazonia (INPA), Manaus, AM (Brazil)]. E-mail: duzat@inpa.gov.br; apaula@inpa.gov.br

2000-07-01

As an alternative to the expensive and high energy consuming conventional dryers available at the market, INPA developed a solar wood dryer technically adequate to the climatic conditions of the Amazon region, and economically suitable to an industrial segment that could not afford large investments to dry wood. The dryer has received great acceptance by the industry due to its low cost and good operating efficiency. The prototype was dimensioned with a capacity of 5 to 8 m{sup 3} of sawn wood, which is sufficient for the needs of small sawmills or furniture shops. A total of 20 units have been installed in Brazil and other countries. Research work is underway to improve the performance of the original model, and some modifications are conducted to adapt it to dry other natural products as seeds, nuts, fruits, and herbs. (author)

7 CFR 2902.34 - Carpet and upholstery cleaners.

Science.gov (United States)

2010-01-01

... procurement applies are: (i) General purpose cleaners. Carpet and upholstery cleaners formulated for use in... PROCUREMENT Designated Items § 2902.34 Carpet and upholstery cleaners. (a) Definition. (1) Cleaning products... upholstery cleaners shall be based on the amount of qualifying biobased carbon in the product as a percent of...

solar dryer with biomass backup heater for drying fruits

African Journals Online (AJOL)

SOLAR DRYER WITH BIOMASS BACKUP HEATER FOR DRYING FRUITS: DEVELOPMENT AND PERFORMANCE ANALYSIS. ... Journal of Science and Technology (Ghana) ... Most solar dryers rely on only solar energy as the heat source.

Fatal accidental inhalation of brake cleaner aerosols.

Science.gov (United States)

Veit, F; Martz, W; Birngruber, C G; Dettmeyer, R B

2018-04-23

Brake cleaner liquid is commonly used for cleaning of engines and motor parts. The commercially available products usually contain mainly volatile organic compounds. As a consequence brake cleaner evaporates fast and almost completely from the cleaned surface. This case report presents a fatal accidental inhalation of brake cleaner liquid aerosols due to the attempted cleaning of a boat engine. A 16year old boy was found lifeless in the engine compartment of a boat engine. In close proximity to the body, the police found cleanings wipes soaked with brake cleaner as well as a pump spray bottle filled with brake cleaner. Essentially the autopsy revealed a cerebral oedema with encephalomalacia, no coagulated blood as well as increased blood and tissue fluid content of the lung. Toxicological analysis revealed brake cleaner fluid in the lung, gastric content and heart blood. Copyright © 2018 Elsevier B.V. All rights reserved.

Bed mixing dryer for high moisture content fuels

Energy Technology Data Exchange (ETDEWEB)

Hulkkonen, S; Heinonen, O. [Imatran Voima Oy, Vantaa (Finland)

1998-12-31

Bed mixing dryer is a new type of fuel drying technology for fluidized bed combustion. The idea is to extract hot bed material from the fluidized bed and use it as a heat source for drying the fuel. Drying occurs at steam atmosphere which makes it possible to recover the latent heat of evaporation to process. This improves the thermal efficiency of the power plant process considerably, especially in combined heat and power applications. Imatran Voima Oy (IVO) has developed the Bed Mixing Dryer technology since early 1990s. The first pilot plant was built in 1994 to IVO`s Kuusamo peat and wood fired power plant. The capacity of the plant is 6 MW{sub e} and 20 MW of district heat. In Kuusamo the dryer is connected to a bubbling fluidized bed. Since it`s commissioning the dryer has been used successfully for about 3000 hours during the heating season in wintertime. The second application of the technology will be a demonstration project in Oerebro (S). IVO Power Engineering Ltd will supply in 1997 a dryer to Oerebro Energi`s peat, wood and coal fired CHP plant equipped with circulating fluidized bed boiler. The fuel to be dried is sawdust with fuel input of about 60 MW. In Kuusamo the dryer produces 3 MW of additional district heat and in Oerebro 6 MW. The fuels in Kuusamo are peat, saw dust and bark. In addition to the municipal heat production this type of drying technology has its benefits in pulp and paper industry processes. Disposal of paper mill sludges is becoming more difficult and costly which has resulted in need of alternative treatment. Drying of the sludge before combustion in a boiler for power production is an attractive option. At the moment IVO is carrying out several studies to apply the Bed Mixing Dryer in pulp and paper industry processes. Economy of drying the sludge looks promising

Bed mixing dryer for high moisture content fuels

Energy Technology Data Exchange (ETDEWEB)

Hulkkonen, S.; Heinonen, O. [Imatran Voima Oy, Vantaa (Finland)

1997-12-31

Bed mixing dryer is a new type of fuel drying technology for fluidized bed combustion. The idea is to extract hot bed material from the fluidized bed and use it as a heat source for drying the fuel. Drying occurs at steam atmosphere which makes it possible to recover the latent heat of evaporation to process. This improves the thermal efficiency of the power plant process considerably, especially in combined heat and power applications. Imatran Voima Oy (IVO) has developed the Bed Mixing Dryer technology since early 1990s. The first pilot plant was built in 1994 to IVO`s Kuusamo peat and wood fired power plant. The capacity of the plant is 6 MW{sub e} and 20 MW of district heat. In Kuusamo the dryer is connected to a bubbling fluidized bed. Since it`s commissioning the dryer has been used successfully for about 3000 hours during the heating season in wintertime. The second application of the technology will be a demonstration project in Oerebro (S). IVO Power Engineering Ltd will supply in 1997 a dryer to Oerebro Energi`s peat, wood and coal fired CHP plant equipped with circulating fluidized bed boiler. The fuel to be dried is sawdust with fuel input of about 60 MW. In Kuusamo the dryer produces 3 MW of additional district heat and in Oerebro 6 MW. The fuels in Kuusamo are peat, saw dust and bark. In addition to the municipal heat production this type of drying technology has its benefits in pulp and paper industry processes. Disposal of paper mill sludges is becoming more difficult and costly which has resulted in need of alternative treatment. Drying of the sludge before combustion in a boiler for power production is an attractive option. At the moment IVO is carrying out several studies to apply the Bed Mixing Dryer in pulp and paper industry processes. Economy of drying the sludge looks promising

Assessment of the bacterial contamination of hand air dryer in washrooms

OpenAIRE

Alharbi, Sulaiman Ali; Salmen, Saleh Hussein; Chinnathambi, Arunachalam; Alharbi, Naiyf S.; Zayed, M.E.; Al-Johny, Bassam O.; Wainwright, Milton

2016-01-01

The present study was carried out, using standard techniques, to identify and count the bacterial contamination of hand air dryers, used in washrooms. Bacteria were isolated from the air flow, outlet nozzle of warm air dryers in fifteen air dryers used in these washrooms. Bacteria were found to be relatively numerous in the air flows. Bacterially contaminated air was found to be emitted whenever a warm air dryer was running, even when not being used for hand drying. Our investigation shows th...

QFD analysis of RSRM aqueous cleaners

Science.gov (United States)

Marrs, Roy D.; Jones, Randy K.

1995-01-01

This paper presents a Quality Function Deployment (QFD) analysis of the final down-selected aqueous cleaners to be used on the Redesigned Solid Rocket Motor (RSRM) program. The new cleaner will replace solvent vapor degreasing. The RSRM Ozone Depleting Compound Elimination program is discontinuing the methyl chloroform vapor degreasing process and replacing it with a spray-in-air aqueous cleaning process. Previously, 15 cleaners were down-selected to two candidates by passing screening tests involving toxicity, flammability, cleaning efficiency, contaminant solubility, corrosion potential, cost, and bond strength. The two down-selected cleaners were further evaluated with more intensive testing and evaluated using QFD techniques to assess suitability for cleaning RSRM case and nozzle surfaces in preparation for adhesive bonding.

Development and Evaluation of Solar Tunnel Dryer for Commercial Fish Drying

Science.gov (United States)

Mohod, A. G.; Khandetod, Y. P.; Shrirame, H. Y.

2014-01-01

The local practice of drying fish in open sun drying poses problems such as high moisture content, uncontrolled drying and contamination. These problems can be avoided by proper use of improved methods such as the solar tunnel dryer, which results in faster drying of fish. The semi cylindrical walk-in type natural convection solar tunnel dryer, having drying area of 37.5 m2 was developed and evaluated for the drying of fish products in comparison with the conventional method of open sun drying. The experiments were conducted without fish and with fish to evaluate the performance of solar tunnel dryer. The average rise in temperature inside the solar tunnel dryer was found to be 11.24 °C and 18.29 °C over the ambient temperature during no load test in winter and summer respectively. The average 28 % saving in time was observed for selected fish drying using solar tunnel dryer over open sun drying method with average drying efficiency of 19 %. The economics was calculated for drying of prawns ( Parapaeneopsis stylifera) by solar tunnel dryer and open sun drying system on the basis of business as a whole. The economics of the solar tunnel dryer is presented in term of Net present worth, Benefit-Cost Ratio, Payback period, Profitability index and Internal rate of return. The pay back period for solar tunnel dryer was found to be 2.84 years.

Neural network modeling of drying of rice in BAU-STR dryer

Science.gov (United States)

Alam, Md. Ashraful; Saha, Chayan Kumer; Alam, Md. Monjurul; Ashraf, Md. Ali; Bala, Bilash Kanti; Harvey, Jagger

2018-05-01

The experimental performance and artificial neural network modeling of rice drying in BAU-STR dryer is presented in this paper. The dryer consists of a biomass stove as a heat source, a perforated inner bin and a perforated outer bin with annular space for grains, and a blower (1 hp) to supply heated air. The dryer capacity was 500 kg of freshly harvested rice. Twenty experimental runs were conducted to investigate the experimental performance of the dryer for drying of rice. An independent multilayer neural network approach was used to predict the performance of the BAU-STR dryer for drying of rice. Ten sets of experimental data were used for training using back propagation algorithm and another ten sets of data were used for testing the artificial neural network model. The prediction of the performance of the dryer was found to be excellent after it was adequately trained. The statistical analysis showed that the errors (MSE and RMSE) were within and acceptable range of ±5% with a coefficient of determination (R2) of 99%. The model can be used to predict the potential of the dryer for different locations, and can also be used in a predictive optimal control algorithm.

Evaluation of hybrid solar – biomass dryer with no load

Directory of Open Access Journals (Sweden)

Yassen Tadahmun Ahmed

2014-07-01

Full Text Available Experimental study was carried out to investigate the performance of designed and fabricated hybrid solar-biomass dryer without load. The solar side was a natural convection mixed mode, while the biomass side was a hot air produced from a burner/gas to gas heat exchanger. The experiments have been conducted to test the dryer temperature, inlet and outlet relative humidity, outlet velocity, and biomass feeding rate. In the solar mode the maximum dryer temperature was 63°C. Behaviours of the velocity in the dryer was found to follow solar radiation available to the dryer. The velocity was in the range of 0.6 – 1.35 m/s through the 0.0176 m2 area of the outlet when the solar radiation was in the range of 150 – 880 W/m2. Two feeding rates of wood were used to investigate the dryer performance through the night. The results showed that at feeding rate 278 g/hr, the drying air mean temperature was 62 ºC. This temperature was more suitable than the measured drying air temperature at feeding rate 490 g/hr. Also the 62 °C drying environment is more stable and feasible for drying almost all types of products.

Effectiveness of a heat exchanger in a heat pump clothes dryer

Science.gov (United States)

Nasution, A. H.; Sembiring, P. G.; Ambarita, H.

2018-02-01

This paper deals with study on a heat pump clothes dryer coupled with a heat exchanger. The objective is to explore the effects of the heat exchanger on the performance of the heat pump dryer. The heat pump dryer consists of a vapor compression cycle and integrated with a drying room with volume 1 m3. The power of compressor is 800 Watt and the refrigerant of the cycle is R22. The heat exchanger is a flat plate type with dimensions of 400 mm × 400 mm × 400 mm. The results show the present of the heat exchanger increase the performance of the heat pump dryer. In the present experiment the COP, TP and SMER increase 15.11%, 4.81% and 58.62%, respectively. This is because the heat exchanger provides a better drying condition in the drying room with higher temperature and lower relative humidity in comparison with heat pump dryer without heat exchanger. The effectiveness of the heat exchanger is also high, it is above 50%. It is suggested to install a heat exchanger in a heat pump dryer.

Use of the solar and eolic energy in the drying of bean seed at rural level

International Nuclear Information System (INIS)

Grajales Avila, W.; Racines Sanchez, L.E.

1985-01-01

The drying is a camera through which is made pass air heated in a solar collector, by means of a rotational fan impelled by the wind. The dryer is wooden and the zinc consists of five levels where the trays are deposited that contain the product. In the end of the chimney placed above the drying camera this the fan that is a rotor of corrugate fins; when rotating under the action of the wind it extracts air of the ventilation chimney; in the periods that the wind doesn't blow the drying it happens for natural convention. In the collector the badge absorbent is zinc colored corrugate of black; the mark is wooden, isolated in its inferior part with icopor and the cover a sheet of plastic. To evaluate the dryer they were carried out four drying rehearsals with seed of bean variety Calima. One observes that the bean drying with this dryer type is feasible even with cloudy or partially cloudy sky. The drying was satisfactory with the two loads of 200 and 400 kg. With the flow of air through the trays and for the load of 210 kg with flow around them; being the drying uniform for this it finishes. The quality of the seeds was not affected in the drying coke superior temperatures they were presented to 43-centigrade degrees. The dryer can adapt to individual necessities and conditions you specify of operation. It is recommended to carry out rehearsals for other agricultural products that allow knowing the capacity and functionality from the dryer to property level

Evaluation of the cleaner technology programme

DEFF Research Database (Denmark)

Andersen, Mikael Skou; Jørgensen, Ulrik

The report presents an independent evaluation of the Danish development programme for cleaner technology 1986-1989 and of the Action Plan for Cleaner Technology 1990-1992. The evaluation focuses on the results of technology development and implementation projects, on an examination...... of the dissemination of cleaner technology solutions achieved in six industrial branches, and on the overall programme and its effects, in particular environmental impacts, but also results in the form of employment, environmental export, strenghtening of Danish know-how etc....

Performance of a desiccant assisted packed bed passive solar dryer for copra processing

Directory of Open Access Journals (Sweden)

Padmanaban Govindarajulu

2017-01-01

Full Text Available In this paper, the performance of a novel desiccant assisted packed bed passive solar dryer was evaluated for copra processing and compared with conventional passive solar dryer. This novel solar dryer consists of a desiccant assisted packed bed solar air heater attached with a dryer cabin. The desiccant and phase change materials packed in the solar air heater has control the humidity and retains the heat for longer duration, respectively. The performance of the dryer was evaluated (in terms of drying time to attain the final equilibrium moisture content, drying rate, specific moisture extraction rate, pick-up efficiency, and dryer efficiency under the meteorological conditions of Coimbatore city in India during March and April 2016. The copra was dried from initial moisture content (wet basis of about 52% to the final moisture content (wet basis of about 8% in 62 hours with specific moisture extraction rate of 0.82 kg/kWh. The drying time was reduced by about 44 hours when compared to the conventional passive solar dryer. The dryer pick-up efficiency was varied between about 10% and 65%. The average dryer thermal efficiency was calculated to be about 32%. The quality of final dried product was found to be good.

New complex-dryers with RE for coatings

International Nuclear Information System (INIS)

Ge, G.

1998-01-01

Full text: The complex coating dryers are produced with good 2-Ethylhexanoic acid, rare earths and other metals. Simply using such a complex drier can get the total effect instead of the traditional dryers such as Co, Mn, Pb, Zn, Ca etc. It has advantages of saving quantity, decreasing cost, simplifying process, making the operation convenient, good quality, good stability and without Pb. Invention patent of China requisition number is 95119867.X

The impact of immersion protection requirements on hair dryer electrocutions in the USA.

Science.gov (United States)

Rodgers, Gregory B; Garland, Sarah

2012-12-01

To evaluate the effectiveness of the immersion protection requirements of a voluntary safety standard for portable handheld hair dryers in preventing electrocution deaths in the USA. The present work was an interrupted time series study design. Data on annual hair dryer-related electrocution deaths resulting from water contact were developed for the 1980-2007 study period. A multivariate Poisson regression model for rate data was used to evaluate the impact of the immersion protection requirements during the post-intervention period. The analysis controlled for the estimated number of hair dryers in use and the estimated number of US homes equipped with ground fault circuit interrupters, safety devices that would address hair dryer electrocutions even in the absence of the immersion protection requirements of the voluntary standard. The implementation of the 1987 and 1991 immersion protection requirements of the voluntary standard for portable handheld hair dryers was the intervention studied. The main outcome measure was the estimated reduction in the hair dryer electrocution rate associated with the immersion protection requirements of the voluntary standard. After controlling for covariates, the immersion protection requirements were estimated to reduce the rate of hair dryer immersion electrocution deaths by 96.6% (95% CI, 90.8% to 98.8%). This suggests the prevention of about 280 immersion electrocution deaths involving hair dryers during the post-intervention period (1987-2007). The immersion protection requirements of the voluntary safety standard for hair dryers have been highly effective in reducing hair dryer electrocutions.

Design of Agricultural Cleaner Production Technology System

OpenAIRE

Hu, Jun-mei; Wang, Xin-jie

2009-01-01

Based on the introduction of agricultural cleaner production, technology system design of planting cleaner production is discussed from five aspects of water-saving irrigation technology, fertilization technology, diseases and insects control technology, straw comprehensive utilization technology and plastic film pollution control technology. Cleaner production technology system of livestock and poultry raise is constructed from the aspects of source control technology, reduction technique in...

New practical method for evaluation of a conventional flat plate continuous pistachio dryer

Energy Technology Data Exchange (ETDEWEB)

Kouchakzadeh, Ahmad [Agri Machinery Engineering, Ilam University, Ilam (Iran, Islamic Republic of); Tavakoli, Teymur [Agri Machinery Engineering, Tarbyat Modares University, Tehran (Iran, Islamic Republic of)

2011-07-15

Highlights: {yields} Evaluation of a conventional flat plate continuous pistachio dryer with a new feasible method. {yields} Using thermophysical properties of air and matter. {yields} This manner could be utilized in similar dryer for other agricultural products. {yields} Method shows the heat loss and power separately. -- Abstract: Testing a dryer is necessary to evaluate its absolute and comparative performance with other dryers. A conventional flat plate continuous pistachio dryer was tested by a new practical method of mass and energy equilibrium. Results showed that the average power consumption and heat loss in three tests are 62.13 and 18.99 kW, respectively. The ratio of heat loss on power consumption showed that the efficiency of practical pistachios flat plate dryer is about 69.4%.

New practical method for evaluation of a conventional flat plate continuous pistachio dryer

International Nuclear Information System (INIS)

Kouchakzadeh, Ahmad; Tavakoli, Teymur

2011-01-01

Highlights: → Evaluation of a conventional flat plate continuous pistachio dryer with a new feasible method. → Using thermophysical properties of air and matter. → This manner could be utilized in similar dryer for other agricultural products. → Method shows the heat loss and power separately. -- Abstract: Testing a dryer is necessary to evaluate its absolute and comparative performance with other dryers. A conventional flat plate continuous pistachio dryer was tested by a new practical method of mass and energy equilibrium. Results showed that the average power consumption and heat loss in three tests are 62.13 and 18.99 kW, respectively. The ratio of heat loss on power consumption showed that the efficiency of practical pistachios flat plate dryer is about 69.4%.

Mitigation effects of radon decay products by air cleaner

International Nuclear Information System (INIS)

Kazuki Iwaoka; Tetsuo Ishikawa; Hidenori Yonehara; Shinji Tokonami

2013-01-01

One of the most effective methods for reducing exposure is the use of air cleaners. In this study, a dose mitigation of a commonly-used Japanese air cleaner under conditions in which aerosols are continuously supplied was investigated. Although the values of the EERC during an operation of air cleaner decreased, values of the f p increased with the use of air cleaner. An effective dose was calculated on the basis of our experimental results, resulting in the dose mitigation of about 40 % by the air cleaner. Air cleaners can be regarded as an effective tool for the dose mitigation under with conditions in which aerosols are continuously supplied. (author)

Drivers for Cleaner Production in Malaysian Industry

DEFF Research Database (Denmark)

Wangel, Arne

2003-01-01

This working paper tries to piece together information on regulatory initiatives promoting cleaner production (CP) in Malaysian industry, as well as points of discussion on environmental performance in the sector. It draws upon initial data collection by the team of the research project ‘A Study...... on Promotion and Implementation of Cleaner Production Practices in Malaysian Industry - Development of a National Program and Action Plan for Promotion of Cleaner Production’, which is coordinated by Institute of Environmental and Resource Management, Universiti Teknologi Malaysia; the objective of this study...... is ‘to formulate, establish and develop a comprehensive "National Cleaner Production Promotion Program" for Malaysia’....

Development and performance evaluation of forced convection potato solar dryer

International Nuclear Information System (INIS)

Khan, M.A.; Sabir, M.S.; Iqbal, M.

2011-01-01

This research paper deals with the design development and testing of a forced convection solar dryer, for drying and converting to flour of high moisture content vegetables like potatoes. The angle of solar collector was made adjustable for the absorption of maximum solar radiation by the absorber plate. The air flow rate was controlled by adjustable gate valve to find the optimum flow rate for dehydration of the product. The penetration of solar radiation raised the temperature of the absorber plate of the dryer to 110 deg. C during the operation under stagnation or no load conditions. The maximum air temperature attained in the solar air heater, under this condition was 80 deg. C. The dryer was loaded with 12 Kg of blanched potato chips having an initial moisture content of 89.75%, and the final desired moisture content of 6.95% was achieved within five hours without losing the color of potato chips, while the moisture contents reduction was from 89.75% to 33.75% for five hours in open sun drying under shade. The drying cost for 1 Kg of potatoes was calculated as Rs. 245 and it was Rs. 329 in the case of an electric dryer. The life span of the solar dryer was assumed to be 20 years. The cumulative present worth of annual savings over the life of the solar dryer was calculated for blanched potato chips drying, and it turned out be Rs.163177.67/- which was much higher than the capital cost of the dryer (Rs. 25000). The payback period was calculated as 0.89 years, which was also very small considering the life of the system (20 years). (author)

7 CFR 2902.48 - General purpose household cleaners.

Science.gov (United States)

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false General purpose household cleaners. 2902.48 Section... PROCUREMENT Designated Items § 2902.48 General purpose household cleaners. (a) Definition. Products designed... procurement preference for qualifying biobased general purpose household cleaners. By that date, Federal...

Parasite infestation increases on coral reefs without cleaner fish

Science.gov (United States)

Grutter, A. S.; De Brauwer, M.; Bshary, R.; Cheney, K. L.; Cribb, T. H.; Madin, E. M. P.; McClure, E. C.; Meekan, M. G.; Sun, D.; Warner, R. R.; Werminghausen, J.; Sikkel, P. C.

2018-03-01

Mutualisms are pivotal in shaping ecological communities. Iconic images of cleaner fish entering the mouths of predatory fish clients to remove ectoparasites epitomize their mutual benefit. Experimental manipulations of cleaner wrasse reveal declines in fish size and growth, and population abundance and diversity of client fishes in the absence of cleaner wrasse. Fishes grow more slowly and are less abundant and diverse on reefs without cleaner wrasse, both for larger species that are regularly cleaned and have high ectoparasite loads ("attractive species"), and for those smaller species that are rarely cleaned and are rarely infested with parasites ("unattractive species"). We therefore considered whether these previously observed declines in individual and population parameters on reefs without cleaners were related to increased ectoparasite infestation using an attractive species ( Hemigymnus melapterus, Labridae) and an unattractive species ( Pomacentrus amboinensis, Pomacentridae). Traps with these fish as a form of bait were deployed to sample blood-sucking gnathiid ectoparasites (Gnathiidae: Isopoda) on reefs from which cleaners ( Labroides dimidiatus, Labridae) have been removed for 13 yr. Cleaner fish could not enter traps to access the clients/hosts, but gnathiids could enter the traps to infest hosts; thus, this method sampled the indirect effect of cleaners on gnathiid infestation of fish. Infestation was higher on reefs without cleaners than on those with them. The effect was only detected during the daytime when cleaners are active and only on the attractive species ( H. melapterus). Thus, cleaner presence indirectly reduced fish exposure to parasites in a species that is highly susceptible to parasites, but not in one that is rarely infested with parasites. This suggests that cleaner presence indirectly reduces exposure of a common fish species to harmful parasites, which may explain some observed benefits in fishes at this location.

MICROBIOLOGICAL CHARACTERISTICS OF THE AIR BLOWN BY WARM AIR HAND DRYERS

Directory of Open Access Journals (Sweden)

Recai OÐUR; Omer Faruk TEKBAS; Osman HANCI; Umut OZCAN

2005-02-01

Full Text Available The aim of the study was to determine the microbiological characteristics of air blown from warm air hand dryers, and to compare findings with the microbiological characteristics of indoor air in which the dryer settled. Air samples was taken from different public places (shopping centers, restaurants and hospitals and investigated for total viable counts, coagulase negative Staphylococcus, E. Coli, Staphylococcus aureus and enteric pathogens. There were differences between sampling indoor places for some of the microorganisms, but all of the air samples taken from dryers contained more microorganisms than indoor air, and the differences between hand dryers and indoor air were statistically significant (p<0.05 except for enteric pathogens. As a result it could be said that warm air hand dryers could be microbiological contamination sources in restrooms or the other places that they are used. [TAF Prev Med Bull 2005; 4(1.000: 1-7

Integration of thickener underflow into thermal dryer circuit. Final report

Energy Technology Data Exchange (ETDEWEB)

McClaine, A.W.; Breault, R.W.

1998-12-31

A large number of coal preparation plants in the United States are troubled with coal fines and associated plant operation problems. As part of their process, these plants use thermal dryers for producing product coal, cyclones for first-stage recovery of coal fines, and wet scrubbers for the second-stage removal of coal fines carry-over from the dryer exhaust gas. The first challenge for these plants is to recover the clean ultra-fine coal captured in the scrubbers rather than to dispose of it in settling ponds. The second challenge is to mitigate the over-dry fine coal dusting problems in the dryer product. Prior to the completion of this program, the difficulties of the first challenge involving the recovery and use of fine clean coal from the thermal dryer scrubber effluent had not been solved. The second challenge, controlling fine coal dusting, was previously met by applying a solution of surfactants and process water to the over-dry coal fraction. As a result of the demonstration provided by the performance of this program, the implementation of a simple process improvement, involving the use of a thickener in combination with a belt press, simultaneously solved both challenges: the de-dusting and the dryer scrubber effluent recovery issues. The objective of this project was to: (1) Use a clean coal thickener with a squeeze belt press to recover the ultra-fine coal in dryer scrubber effluent; (2) Demonstrate that the coal-water mixture (CWM) produced from scrubber sludge of a thermal dryer can be used as a dust suppressant. The thickener/belt press system has increased the production of JWRI Mine Number 4 by approximately 0.7%. This production increase was accomplished by recovering and re-using 3 metric tons/hr (3.3 tons/hr) of coal fines that were previously sent to holding ponds, returning this as a 50% CWM to de-dust the 430 metric tons/hr (470 tons/hr) of existing dryer production.

Beyond symbiosis: cleaner shrimp clean up in culture.

Science.gov (United States)

Militz, Thane A; Hutson, Kate S

2015-01-01

Cleaner organisms exhibit a remarkable natural behaviour where they consume ectoparasites attached to "client" organisms. While this behaviour can be utilized as a natural method of parasitic disease control (or biocontrol), it is not known whether cleaner organisms can also limit reinfection from parasite eggs and larvae within the environment. Here we show that cleaner shrimp, Lysmata amboinensis, consume eggs and larvae of a harmful monogenean parasite, Neobenedenia sp., in aquaculture. Shrimp consumed parasite eggs under diurnal (63%) and nocturnal (14%) conditions as well as infectious larvae (oncomiracidia) diurnally (26%). Furthermore, we trialled the inclusion of cleaner shrimp for preventative parasite management of ornamental fish, Pseudanthias squamipinnis, and found shrimp reduced oncomiracidia infection success of host fish by half compared to controls (held without shrimp). Fish held without cleaner shrimp exhibited pigmentation changes as a result of infection, possibly indicative of a stress response. These results provide the first empirical evidence that cleaner organisms reduce parasite loads in the environment through non-symbiotic cleaning activities. Our research findings have relevance to aquaculture and the marine ornamental trade, where cleaner shrimp could be applied for prophylaxis and control of ectoparasite infections.

Test and study for dryer used in steam generator

International Nuclear Information System (INIS)

Xue Yunkui; Liu Shixun; Xie Guandao; Chen Junliang

1994-10-01

Dryer used in steam generator is composed of hooked-vanes and draining structure. The influences of the number of drainage hooks on a hooked-vane, bending angle, distance between two adjacent hooked-vanes, etc. on separation effect are introduced. The improving process of draining structure is also described. The test indicates that the hooked-vanes type dryer allows to change inlet moisture in a large range and that the performance of the dryer is closely related to draining structure. A draining structure with original creation which is selected by the test is presented, its drainage effect is better than that of similar structures at home and abroad. (2 tabs., 21 figs.)

Further development of a mixed-dryer for wood biomass; Sekoituskuivurin jatkokehitys

Energy Technology Data Exchange (ETDEWEB)

Heinonen, O. [Imatran Voima Oy, Vantaa (Finland). Research and Development; Parvio, E. [IVO International Oy, Vantaa (Finland)

1995-12-31

Imatran Voima Oy and IVO International Ltd are developing a new, advanced drying method for high moisture content fuels such as peat, biomass, and brown coal. The drying technology is based on using the heat of the fluidized bed directly for drying. The drying takes place at steam atmosphere, which makes it possible to recover the latent heat of evaporation back to process at high temperature level. This improves the thermal efficiency of the plant considerably. The technology is called bed mixing dryer. The pilot plant of the bed mixing dryer was built to IVO`s Kuusamo peat and wood fired power plant that was commissioned in the beginning of 1994. The Kuusamo district heating power plant has a fuel input of 27 MW that gives a power output of 6 MWe and district heat output of 17.5/21.2 MWth. As fuels are used peat, saw dust and wood wastes. The boiler is a bubbling fluidized bed boiler and the steam cycle is a conventional back pressure steam process. The unique feature in the plant is the new dryer that increases the overall thermal efficiency of the plant 10 to 15 units of percentage. In this project the operation and behaviour of the bed mixing dryer has been examined. Various components of the dryer were developed by the cold model tests carried out at IVO`s laboratory in Helsinki. Testing with the Kuusamo bed mixing dryer consisted of about 390 hours of drying tests with peat, bark and saw dust. The dryer operated well, and the drying was effective. The measured final moisture content varied from 7 to 19 % depending on the fuel particle size and the temperature level of the dryer

Further development of a mixed-dryer for wood biomass; Sekoituskuivurin jatkokehitys

Energy Technology Data Exchange (ETDEWEB)

Heinonen, O. [Imatran Voima Oy, Vantaa (Finland). Research and Development; Parvio, E [IVO International Oy, Vantaa (Finland)

1996-12-31

Imatran Voima Oy and IVO International Ltd are developing a new, advanced drying method for high moisture content fuels such as peat, biomass, and brown coal. The drying technology is based on using the heat of the fluidized bed directly for drying. The drying takes place at steam atmosphere, which makes it possible to recover the latent heat of evaporation back to process at high temperature level. This improves the thermal efficiency of the plant considerably. The technology is called bed mixing dryer. The pilot plant of the bed mixing dryer was built to IVO`s Kuusamo peat and wood fired power plant that was commissioned in the beginning of 1994. The Kuusamo district heating power plant has a fuel input of 27 MW that gives a power output of 6 MWe and district heat output of 17.5/21.2 MWth. As fuels are used peat, saw dust and wood wastes. The boiler is a bubbling fluidized bed boiler and the steam cycle is a conventional back pressure steam process. The unique feature in the plant is the new dryer that increases the overall thermal efficiency of the plant 10 to 15 units of percentage. In this project the operation and behaviour of the bed mixing dryer has been examined. Various components of the dryer were developed by the cold model tests carried out at IVO`s laboratory in Helsinki. Testing with the Kuusamo bed mixing dryer consisted of about 390 hours of drying tests with peat, bark and saw dust. The dryer operated well, and the drying was effective. The measured final moisture content varied from 7 to 19 % depending on the fuel particle size and the temperature level of the dryer

Processamento de achocolatado de cupuaçu por spray-dryer Cupuassu chocolate drink powder processed by spray-dryer

Directory of Open Access Journals (Sweden)

Suzana Caetano da Silva Lannes

2003-03-01

Full Text Available O achocolatado de cupuaçu é uma mistura do pó de cupuaçu, açúcar, aroma e outros ingredientes constantes da formulação. Este produto formulado foi processado por spray-dryer, gerando um produto seco, pulverizado e instantaneizado. O achocolatado acrescido de água (concentrado passa pelo spray-dryer formando glóbulos de pequeno diâmetro que são arrastados por uma corrente de ar quente. A rápida evaporação de líquido permite manter baixa a temperatura do ar na secagem, não afetando o produto. O pó de cupuaçu não dispersa prontamente em água devido ao seu conteúdo de óleo. Conseqüentemente, necessita-se de uma forma desengordurada para se obter instantaneização. A secagem por spray-dryer reúne as melhores condições de rendimento técnico em comparação com outros processos. Obtiveram rendimentos de processo acima de 20% e a instantaneização completa do produto.Cupuassu chocolate drink powder is a mixture of cupuassu powder, sugar, flavour and other ingredients of formulation. The product was processed by spray-dryer, leading a dry, pulverized and instantised product. The chocolate drink powder with water (concentrated pass through spray-dryer forming small diameter globules that are arrested by a hot air stream. The rapid evaporation allows keeping low temperature at drying air, and no affecting the product. The process is a set of better conditions of technique and economical efficiency in comparison to other process. Cupuassu powder does not disperse readily in water owing to its oil content. Consequently, a form of cocoa with the oil removed is needed to produce an acceptably instant drink. The results obtained were satisfactory, due to the complete instantisation of the product after processing.

7 CFR 2902.49 - Industrial cleaners.

Science.gov (United States)

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false Industrial cleaners. 2902.49 Section 2902.49... Items § 2902.49 Industrial cleaners. (a) Definition. Products used to remove contaminants, such as..., floors, walls, and other production-related work areas. The cleaning products within this item are...

RELATION BETWEEN FUNCTION AND FORM IN VACUUM CLEANERS DESIGN

Directory of Open Access Journals (Sweden)

RADU Ștefan

2015-11-01

Full Text Available The paper analyses how robotic vacuum cleaner works, describing their cleaning capabilities and additional features. The paper illustrates advantages of using robotic vacuum cleaners that have intelligent programming and a vacuum cleaning system, the components of a robotic vacuum cleaner. The paper develops aspects concerning to create 2D scale models for the evaluation of specific features of the new components for a prototype robotic vacuum cleaner.

Reconstructing the image of the cleaner

NARCIS (Netherlands)

Jorcho van Vlijmen; Toine van den Hoogen

2013-01-01

Purpose: The article shows the relevance of an insider’s perspective on workers in the cleaning industry (cleaners). It explains how the ways in which cleaners create meaning in their work can be explored. These findings help to create added value for FM. Theory: Organisational theory describes a

Inventory on cleaner production education and training

DEFF Research Database (Denmark)

Jørgensen, Michael Søgaard; Pöyry, Sirkka; Huisingh, Donald

Analysis and presentation of the data from an international inventory on cleaner production education and training......Analysis and presentation of the data from an international inventory on cleaner production education and training...

Experimental Investigation on an Energy Efficient Solar Tunnel Dryer

OpenAIRE

M. R. Seshan Ram

2012-01-01

The research determines the effectiveness of the solar tunnel dryer developed and the product dried in the device is superior in quality and also it is compatible with branded products available in the market. The study also determines Acetamide as Phase Key words: Solar Tunnel Dryer, Acetamide as Phase Change Materials, Conversion into Thermal Energy, Thermocouple, and Pyranometer

Health disparities between immigrant and Danish cleaners

DEFF Research Database (Denmark)

Jørgensen, Marie B; Rasmussen, Charlotte D N; Carneiro, Isabella G

2011-01-01

hundred and fifty-one cleaners, consisting of 166 Danes (88% women) and 179 immigrants (74% women) (6 with unknown ethnicity), from 9 workplaces in Denmark participated in the study. Health and work ability were obtained by objective (e.g., BMI and blood pressure) and self-reported measures (e.g., work......PURPOSE: It is unknown whether immigrants working in the cleaning industry have a poorer health and work ability than cleaners from the native population. The main aim was to investigate differences in objective and self-reported health measures between immigrant and Danish cleaners. METHODS: Three...... ability, self-rated health, and musculoskeletal symptoms). In order to investigate differences between Danish and immigrant cleaners, logistic regression analyses and General Linear Models were performed. RESULTS: When controlling for age, sex, workplace, job seniority, and smoking, more Danish compared...

Control Systems of Rubber Dryer Machinery Components Using Programmable Logic Control (PLC)

Science.gov (United States)

Hendra; Yulianto, A. S.; Indriani, A.; Hernadewita; Hermiyetti

2018-02-01

Application of programmable logic control (PLC) is widely used on the control systems in the many field engineering such as automotive, aviation, food processing and other industries [1-2]. PLC is simply program to control many automatic activity, easy to use, flexible and others. PLC using the ladder program to solve and regulated the control system component. In previous research, PLC was used for control system of rotary dryer machine. In this paper PLC are used for control system of motion component in the rubber dryer machinery. Component of rubber dryer machine is motors, gearbox, sprocket, heater, drying chamber and bearing. Principle working of rubber dryer machinery is wet rubber moving into the drying chamber by sprocket. Sprocket is driven by motors that conducted by PLC to moving and set of wet rubber on the drying chamber. Drying system uses greenhouse effect by making hanger dryer design in the form of line path. In this paper focused on motion control system motors and sensors drying rubber using PLC. The results show that control system of rubber dryer machinery can work in accordance control input and the time required to dry the rubber.

Current development of GHE solar dryer

International Nuclear Information System (INIS)

Kamaruddin Abdullah

2006-01-01

Field tests of the previous GHE solar dryer design had shown that the system can be used effectively to dry various agricultural and marine products. In order to improve further the performance of this dryer, particularly, to reduce dependency on electricity, mechanical energy and on heat generated from non-renewable energy sources, several new prototypes are now in the stage of preliminary testing. These new systems were designed to dry granular products using vibrated drums and for non-granular products such as chili, sliced vegetables and fish products using vibrating racks. The hybrid renewable energy system for drying accommodate Savonius windmill for air moving device as well as vibration generator and simple biomass stove as auxiliary heating unit

Modeling and simulation of milk emulsion drying in spray dryers

Directory of Open Access Journals (Sweden)

V. S. Birchal

2005-06-01

Full Text Available This work aims at modeling and simulating the drying of whole milk emulsion in spray dryers. Drops and particles make up the discrete phase and are distributed into temporal compartments following their residence time in the dryer. Air is the continuous and well-mixed phase. Mass and energy balances are developed for each phase, taking into account their interactions. Constitutive equations for describing the drop swelling and drying mechanisms as well as the heat and mass transfer between particles and hot air are proposed and analyzed. A set of algebraic-differential equations is obtained and solved by specific numerical codes. Results from experiments carried out in a pilot spray dryer are used to validate the model developed and the numerical algorithm. Comparing the simulated and experimental data, it is shown that the model predicts well the individual drop-particle history inside the dryer as well as the overall outlet air-particle temperature and humidity.

Herbs drying using a heat pump dryer

Energy Technology Data Exchange (ETDEWEB)

Fatouh, M.; Metwally, M.N.; Helali, A.B.; Shedid, M.H. [Department of Mechanical Power Engineering, Faculty of Engineering at El Mattaria, Helwan University, P.O. Box 11718, Masaken El-Helmia, Cairo (Egypt)

2006-09-15

In the present work, a heat pump assisted dryer is designed and constructed to investigate the drying characteristics of various herbs experimentally. R134a is used as a working fluid in the heat pump circuit during the experimental work. Experiments have been conducted on Jew's mallow, spearmint and parsley. The effects of herb size, stem presence, surface load, drying air temperature and air velocity on the drying characteristics of Jew's mallow have been predicted. Experimental results show that a high surface load of 28kg/m{sup 2} yields the smallest drying rate, while the drying air with temperature of 55{sup o}C and velocity of 2.7m/s achieves the largest drying rate. A maximum dryer productivity of about 5.4kg/m{sup 2}h is obtained at the air temperature of 55{sup o}C, air velocity of 2.7m/s and dryer surface load of 28kg/m{sup 2}. It was found that small size herbs without stem need low specific energy consumption and low drying time. Comparison of the drying characteristics of different herbs revealed that parsley requires the lowest specific energy consumption (3684kJ/kg{sub H{sub 2}O}) followed by spearmint (3982kJ/kg{sub H{sub 2}O}) and Jew's mallow (4029kJ/kg{sub H{sub 2}O}). Finally, dryer productivity has been correlated in terms of surface load, drying air velocity and drying air temperature. (author)

30 CFR 77.307 - Thermal dryers; location and installation; general.

Science.gov (United States)

2010-07-01

... where the heat, sparks, flames, or coal dust from the system might cause a fire or explosion. (b... LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS, SURFACE COAL MINES AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES Thermal Dryers § 77.307 Thermal dryers; location and installation; general...

Hand dryer noise in public restrooms exceeds 80 dBA at 10 ft (3 m

Directory of Open Access Journals (Sweden)

Shari Salzhauer Berkowitz

2015-01-01

Full Text Available High airflow hand dryers are found in many public restrooms today. These dryers offer quick and clean hand drying, and are seen as being an environment-friendly alternative to paper towels. However, many new hand dryers are loud, exposing individuals using the facilities as well as those employees who clean the facilities to potentially dangerous noise. Prolonged exposure to high levels of occupational noise can cause damage to hair cells in the cochlea, resulting in varying degrees of noise-induced hearing loss. This study examined the intensity (in dBA of the noise produced by the air dryers in campus restrooms. Hand dryer peak and average noise was measured with a sound level meter at 2.5 ft, 5 ft, and 10 ft from the dryer. Noise measurements did not decrease as predicted by the inverse-square law, probably because of the reverberative surfaces found in the restrooms. The small sample of hand dryers tested was mostly found to be producing more noise than the manufacturer claimed they would; indeed, none of the dryers would be safe for an 8-h workday exposure. While hand dryers do reduce paper trash, they pose as a different sort of hazard to our environment and population.

Tropical field performance of dual-pass PV tray dryer

Science.gov (United States)

Iskandar, A. Noor; Ya'acob, M. E.; Anuar, M. S.

2017-09-01

Solar Photovoltaic technology has become the preferable solution in many countries around the globe to solve the ever increasing energy demand of the consumers. In line with the consumer need, food processing technology has huge potentials of integration with the renewable energy resources especially in drying process which consumes the highest electricity loads. Traditionally, the solar dryer technology was applied in agriculture and food industries utilizing the sun's energy for drying process, but this is highly dependable on the weather condition and surrounding factors. This work shares some field performance of the new design of portable dual-pass PV tray dryer for drying crops in an enclosed system. The dual-pass PV tray dryer encompass a lightweight aluminium box structure with dimensions of 1.1m (L) x 0.6m (W) x 0.2m (H) and can hold a load capacity of 300g - 3kg of crop depending on the types of the crops. Experiments of field performance monitoring were conducted in October -November 2016 which justifies a considerable reduction in time and crops quality improvement when using the dual-pass PV tray dryer as compared to direct-sun drying.

Materials Compatibility Testing in RSRM ODC: Free Cleaner Selection

Science.gov (United States)

Keen, Jill M.; Sagers, Neil W.; McCool, Alex (Technical Monitor)

2001-01-01

Government regulations have mandated production phase-outs of a number of solvents, including 1,1,1-trichloroethane, an ozone-depleting chemical (ODC). This solvent was used extensively in the production of the Reusable Solid Rocket Motors (RSRMs) for the Space Shuttle. Many tests have been performed to identify replacement cleaners. One major area of concern in the selection of a new cleaner has been compatibility. Some specific areas considered included cleaner compatibility with non-metallic surfaces, painted surfaces, support materials such as gloves and wipers as well as corrosive properties of the cleaners on the alloys used on these motors. The intent of this paper is to summarize the test logic, methodology, and results acquired from testing the many cleaner and material combinations.

Solar dryer with thermal storage and biomass-backup heater

Energy Technology Data Exchange (ETDEWEB)

Madhlopa, A. [Department of Physics and Biochemical Sciences, Malawi Polytechnic, P/Bag 303, Blantyre 3 (Malawi); Ngwalo, G. [Department of Mechanical Engineering, Malawi Polytechnic, P/Bag 303, Blantyre 3 (Malawi)

2007-04-15

An indirect type natural convection solar dryer with integrated collector-storage solar and biomass-backup heaters has been designed, constructed and evaluated. The major components of the dryer are biomass burner (with a rectangular duct and flue gas chimney), collector-storage thermal mass and drying chamber (with a conventional solar chimney). The thermal mass was placed in the top part of the biomass burner enclosure. The dryer was fabricated using simple materials, tools and skills, and it was tested in three modes of operation (solar, biomass and solar-biomass) by drying twelve batches of fresh pineapple (Ananas comosus), with each batch weighing about 20 kg. Meteorological conditions were monitored during the dehydration process. Moisture and vitamin C contents were determined in both fresh and dried samples. Results show that the thermal mass was capable of storing part of the absorbed solar energy and heat from the burner. It was possible to dry a batch of pineapples using solar energy only on clear days. Drying proceeded successfully even under unfavorable weather conditions in the solar-biomass mode of operation. In this operational mode, the dryer reduced the moisture content of pineapple slices from about 669 to 11% (db) and yielded a nutritious dried product. The average values of the final-day moisture-pickup efficiency were 15%, 11% and 13% in the solar, biomass and solar-biomass modes of operation respectively. It appears that the solar dryer is suitable for preservation of pineapples and other fresh foods. Further improvements to the system design are suggested. (author)

Performances of continuous dryer with inert medium fluidized bed

Directory of Open Access Journals (Sweden)

Arsenijević Zorana Lj.

2008-01-01

Full Text Available A fluid bed dryer with inert particles represents a very attractive alternative to other drying technologies according to the main efficiency criteria, i.e. specific water evaporation rate, specific heat consumption and speci­fic air consumption. A high drying efficiency results from the large con­tact area and from the large temperature difference between the inlet and outlet air. A rapid mixing of the particles leads to nearly isothermal conditions throughout the bed. A fluid bed dryer with inert particles was used for drying of slurries. Experiments were performed in a cylindrical column 215 mm in diameter with glass spheres as inert particles. In this paper, results of drying experi­ments with slurries of Zineb fungicide, copper hydroxide, calcium carbo­nate and pure water used as the feed material are presented. In our fluidized bed we successfully dried a number of other materials such as: fungicides and pesticides (Ziram, Propineb, Mangozeb, copper oxy-chloride, copper oxy-sulphate, Bordeaux mixture, other inorganic compounds (calcium sulphate, cobalt carbonate, electrolytic copper, sodium chloride, and a complex compound (organo-bentonite. The effects of operating conditions on dryer throughput and product quality were investigated. Main performance criteria, i.e. specific water evaporation rate, specific heat consumption and specific air consumption, were quantified. Temperature profile along the bed was mapped, and nearly isothermal conditions were found due to thorough mixing of the particles. Analysis of drying and energy efficiencies as a function of inlet and outlet air temperature difference was performed for deeper insight in dryer behavior and for optimizing dryer design and operation from an energy point of view. A simple mathematical model based on an overall heat balance predicts the dryer performance quite well. The industrial prototype with fluid bed of 0.8 m in diameter and capacity 650 kg of evaporated moisture per

Experimental silo-dryer-aerator for the storage of soybean grains

Directory of Open Access Journals (Sweden)

Paulo C. Coradi

Full Text Available ABSTRACT This study aimed to verify the capacity of silo-dryer-aerator prototype equipment operating as a silo-storage-aerator for soybean quality analysis. Soybeans with water content of 17% (wet basis – w.b. were dried and stored in a silo-dryer-aerator system that was designed using a drying chamber, four independent storage cells, and a static capacity of 164 kg. Another batch of grains was stored in a silo-storage-aerator with a capacity of 1,200 kg. The experiment was set up in a completely randomized factorial 5 × 4 experimental design including five grain batches stored after being dried at 30, 40, and 50 °C (mixed grains were dried at three temperatures in the silo-dryer-aerator cells and one mixed grain batch stored in the silo-storage-aerator system under ambient air conditions for four storage times (zero, one, two, and three months. There was no difference between the grains stored in the silo-dryer-aerator and silo-storage-aerator at the end of the three-month storage in terms of the physico-chemical quality. The storage time associated with drying at 50 °C caused a reduction in the physical-chemical quality of the grains. The silo-dryer-aerator system was presented as a possible alternative to store soybean (Glycine max L. grains.

MATHEMATICAL MODELING OF ORANGE SEED DRYING KINETICS

Directory of Open Access Journals (Sweden)

Daniele Penteado Rosa

2015-06-01

Full Text Available Drying of orange seeds representing waste products from juice processing was studied in the temperatures of 40, 50, 60 and 70 °C and drying velocities of 0.6, 1.0 and 1.4 m/s. Experimental drying kinetics of orange seeds were obtained using a convective air forced dryer. Three thin-layer models: Page model, Lewis model, and the Henderson-Pabis model and the diffusive model were used to predict the drying curves. The Henderson-Pabis and the diffusive models show the best fitting performance and statistical evaluations. Moreover, the temperature dependence on the effective diffusivity followed an Arrhenius relationship, and the activation energies ranging from 16.174 to 16.842 kJ/mol

Machine & electrical double control air dryer for vehicle air braking system

Science.gov (United States)

Zhang, Xuan; Yang, Liu; Wang, Xian Yan; Tan, Xiao Yan; Wang, Wei

2017-09-01

As is known to all, a vehicle air brake system, in which usually contains moisture. To solve the problem, it is common to use air dryer to dry compressed air effectively and completely remove the moisture and oil of braking system. However, the existing air dryer is not suitable for all commercial vehicles. According to the operational status of the new energy vehicles in the initial operating period, the structure design principle of the machine & electric control air dryer is expounded from the aspects of the structure and operating principle, research & development process.

Model-Based Energy Efficiency Optimization of a Low-Temperature Adsorption Dryer

NARCIS (Netherlands)

Atuonwu, J.C.; Straten, G. van; Deventer, H.C. van; Boxtel, A.J.B. van

2011-01-01

Low-temperature drying is important for heat-sensitive products, but at these temperatures conventional convective dryers have low energy efficiencies. To overcome this challenge, an energy efficiency optimization procedure is applied to a zeolite adsorption dryer subject to product quality. The

Low cost solar dryer for fish

African Journals Online (AJOL)

Administrator

Department of Electrical and Other Energy Sources, College of Agricultural Engineering and Technology, DBSKKV, ... The average solar energy ranged between 450 - 500 ..... classification and selection of dryers, In Handbook of industrial.

76 FR 22324 - Energy Conservation Program: Energy Conservation Standards for Residential Clothes Dryers and...

Science.gov (United States)

2011-04-21

... standards, the current standards for room air conditioners and clothes dryers, and the history of the... Residential Clothes Dryers and Room Air Conditioners AGENCY: Office of Energy Efficiency and Renewable Energy... equipment, including residential clothes dryers and room air conditioners. EPCA also requires the U.S...

Energy Efficient Clothes Dryer with IR Heating and Electrostatic Precipitator

Energy Technology Data Exchange (ETDEWEB)

Weaver, Stanton [GE Global Research, Niskayuna, NY (United States)

2017-12-12

The project goal was to develop a revolutionary energy saving technology for residential clothes drying. The team developed an IR (infrared) heating system and NESP (Nebulizer and Electro-Static Precipitator) for integration into a ventless clothes dryer. The proposed technology addresses two of the major inefficiencies in current electric vented dryers by providing effective energy transfer for the removal of the water and recapture of the vapor latent heat. The IR heaters operating in the mid wave (2.5-10um) are very efficient as they target the 3-micron peak absorption of the water molecule. This allows direct energy absorption, unlike conventional element heaters where heat is transferred by convection. The low power NESP removes water vapor from the exhausted stream and recaptures the latent heat in the ESP (Electro-Static Precipitator) exchanger section. This allows the warm dry air to be recirculated back into the drum for additional efficiency savings. The remaining majority of the dryer hardware stays the same. Summing the efficiency gain from the two subcomponents we anticipated the EF (Efficiency Factor) to exceed the goal of 4.04. EF is obtained by dividing the weight (lbs) of water removed by the energy (kWhr) used, where the test load size is 8.45 lbs of bone dry clothing wetted to 57.5% or 4.8lbs of water, and dried to a remaining moisture content of 2.5-5%. Additional benefits include not having to recondition (heat or cool) the large amounts of make-up air to replace the air exhausted by a vented dryer. It was anticipated that the NESP/heat exchanger would be the most challenging and highest risk element in the program. Therefore, the team focused their efforts during Phase 1 of the program on the design, construction, testing, and optimization of the NESP/heat exchanger. At the end Phase 1, the team compared the performance of the NESP/heat exchanger with the system level requirements and made a Go/No-Go decision on proceeding with the second

Assessment of differences between products obtained in conventional and vacuum spray dryer

Directory of Open Access Journals (Sweden)

Fernanda de Melo RAMOS

Full Text Available Abstract In this work, an experimental unit of a vacuum spray dryer was built. This prototype attempted to combine the advantages of freeze-drying (drying at low temperatures due to vacuum and spray drying (increase of surface area aiming the improvement of heat transfer efficiency. Maltodextrin solutions were dried in the vacuum operated equipment and in conventional spray dryer. The vacuum spray dryer system allowed obtaining powder at low temperatures due to the lowering of pressure conditions (2-5 kPa inside the drying chamber. The products obtained in the two systems were characterized and compared for particle size distribution, moisture content, water activity, bulk density and solubility in water. The processes yields were also evaluated and compared. The vacuum spray dryer system allowed the production of larger, more soluble and less dense particles than those obtained in the conventional configuration of the equipment, resulting in drier and, therefore, with lower water activity particles. Thus, the use of the vacuum spray dryer as a drying technique may be an alternative for the production of powder rich in thermosensitive compounds.

[Effectiveness and limits of the cleaners steam in hospitals].

Science.gov (United States)

Meunier, O; Meistermann, C; Schwebel, A

2009-05-01

We assessed bactericidal activity of the cleaners steam used for the bio-cleaning of the hospital surfaces. We performed of samples (Rodac) before and after use of cleaner steam and compared with bactericidal effect of disinfecting detergent used in hospital for surfaces. We studied this effectiveness for different time of steam contact. Finally, we wanted to prove, by air sampling, that aero-bio-contamination was possible generated by using cleaners steam. We show that bactericidal effect of the cleaner steam is superior of some tested disinfecting detergent, for the treatment of one square meter till 2 min. This effectiveness diminishes to be just identical in that some disinfecting detergent when use of the cleaner steam is up to two or four square meters surfaces till 2 min. On the other hand, the cleaner steam is less efficient in terms of bacterial destruction when the time of contact steam-soil is superior in 2 min for six square meter surface. The air bacterial pollution, generated by the use of the cleaner steam, is restricted and not significantly augmented if measured in 44 cm above the soil in the course of cleaning. The cleaner steam is indeed a very good equipment for the cleaning of surfaces but it is necessary to respect a time of minimal contact of 2 min for four square meters surfaces treaties to acquire an antibacterial effect at least so important as that acquired with used disinfecting detergent. The disinfection of surfaces is then user-dependent and the time of requested contact is can be not compatible with hospital obligations.

ENERGY STAR Certified Residential Clothes Dryers

Data.gov (United States)

U.S. Environmental Protection Agency — Certified models meet all ENERGY STAR requirements as listed in the Version 1.1 ENERGY STAR Program Requirements for Clothes Dryers that are effective as of January...

Cleaner Production in the mining

International Nuclear Information System (INIS)

Pinto Martinez, Elias

2004-01-01

The control politics of the environmental contamination have substantially changed from the 80, toward new preventive tendencies that make the question. That we make with the residuals? What can we make for not generating residuals? On this position, the topic of clean production, it really indicates environmentally a production cleaner, to generate a more respectful final product with the environment, as a result of a process that incorporates in each one of the phases of the life cycle of products the best environmental practices. The national politics of cleaner production was approved in August of 1997 by the environmental national advice, it was formulated like an answer to the solution of the environmental problem of the productive sectors that looks for fundamentally to prevent the contamination in its origin, instead of treating her once generated, with significant results for the construction of the real possibilities of sustainability and competitiveness. Their implementation requires of the government like of the productive sectors, fundamentally, because the environmental problems have become very complex for its control, only through direct regulation, and because to reach the sustainable development of the productive activities implies to face the new challenges of the national and international competitiveness, considering that the environmental administration is a source of opportunities and not an obstacle. In the practice the application of the concept of cleaner production, so much in the current systems of production like in the products and services, it doesn't mean a substitution in strict sense for other different, but improving them continually, under the expert that the new technologies will be cleaner. Of here that production cleans it profiles as the goal that will be reached with the new investments, as long as the systematic search of the continuous improvement, corresponds to the concept of cleaner production that obeys a dynamic and

A greenhouse type solar dryer for small-scale dried food industries: Development and dissemination

Energy Technology Data Exchange (ETDEWEB)

Janjai, Serm [Solar Energy Research Laboratory, Department of Physics, Faculty of Science, Silpakorn University, Nakhon Pathom 73000 (Thailand)

2012-07-01

In this study, a greenhouse type solar dryer for small-scale dried food industries was developed and disseminated. The dryer consists of a parabolic roof structure covered with polycarbonate sheets on a concrete floor. The system is 8.0m in width, 20.0m in length and 3.5m in height, with a loading capacity about 1,000kg of fruits or vegetables. To ensure continuous drying operation, a 100kW-LPG gas burner was incorporated to supply hot air to the dryer during cloudy or rainy days. Nine 15-W DC fans powered by three 50-W PV modules were used to ventilate the dryer. This dryer was installed for a small-scale food industry at Nakhon Pathom in Thailand to produce osmotically dehydrated tomato. To investigate its performance, the dryer was used to dry 3 batches of osmotically dehydrated tomato. Results obtained from these experiments showed that drying air temperatures in the dryer varied from 35 C to 65 C. In addition, the drying time for these products was 2-3 days shorter than that of the natural sun drying and good quality dried products were obtained. A system of differential equations describing heat and moisture transfers during drying of osmotically dehydrated tomato was also developed. The simulated results agreed well with the experimental data. For dissemination purpose, other two units of this type of dryer were constructed and tested at two locations in Thailand and satisfactory results were obtained.

Design and Evaluation of Solar Grain Dryer with a Back-up Heater

OpenAIRE

K.S. Tonui; E.B.K. Mutai; D.A. Mutuli; D.O. Mbuge; K.V. Too

2014-01-01

The aim of the study was to design and construct a solar grain dryer integrated with a simple biomass burner using locally available materials. This was to address the limitations of the natural sun drying for example drying exposure, liability to pests and rodents, over-dependence on sun and escalated cost of mechanical dryers. This became beneficial especially in reducing post-harvest losses as well as helping in the preservation of agricultural product. The dryer is composed of solar colle...

75 FR 27504 - Substantial Product Hazard List: Hand-Held Hair Dryers

Science.gov (United States)

2010-05-17

... immersion during their use. Section 15(a) of the CPSA defines ``substantial product hazard'' to include, a....'' Hand-held hair dryers routinely contain open-coil heating elements that are, in essence, uninsulated..., bathtub, or lavatory). The proposed rule would define ``hand-held hair dryer'' as ``an electrical...

The Development Of Cleaner Production Practices Between Environmental

DEFF Research Database (Denmark)

Wangel, Arne; Mohamed, Maketab; Agamuthu, P.

2003-01-01

(DANCED), Ministry of Environment and Energy. Small and medium-scale enterprises (SMEs) were targeted within three sectors: Textile, food and electroplating industries. The paper illustrates the change process from the perspective of electroplating SMEs by reviewing the cleaner production options chosen......, presenting figures on the results achieved, and discussing the experiences gained. Reviewing the approach and results of the Centre, as well as the status of cleaner production (CP) in Malaysia, the paper outlines the challenges for national policy making, when moving from promotion by project intervention...... towards sustainable practices in the SME sector at large. The paper draws upon data collection conducted by the research project ‘A Study on Promotion and Implementation of Cleaner Production Practices in Malaysian Industry - Development of a National Program and Action Plan for Promotion of Cleaner...

Demonstration of Clean Particle Seeding for Particle Image Velocimetry in a Closed Circuit Supersonic Wind Tunnel

National Research Council Canada - National Science Library

McNiel, Charles M

2007-01-01

The purpose of this research was to determine whether solid carbon dioxide (CO2) particles might provide a satisfactory, and cleaner, alternative to traditional seed material for Particle Image Velocimetry (PIV...

24 CFR 3280.708 - Exhaust duct system and provisions for the future installation of a clothes dryer.

Science.gov (United States)

2010-04-01

...(a)(1) through (5). (c) Provisions for future installation of electric clothes dryers. When wiring is... for the future installation of a clothes dryer. 3280.708 Section 3280.708 Housing and Urban... duct system and provisions for the future installation of a clothes dryer. (a) Clothes dryers. (1) All...

75 FR 7987 - Energy Conservation Standards for Residential Clothes Dryers and Room Air Conditioners: Public...

Science.gov (United States)

2010-02-23

... Conservation Standards for Residential Clothes Dryers and Room Air Conditioners: Public Meeting and... conservation standards for residential clothes dryers and room air conditioners; the analytical framework..., Mailstop EE-2J, Public Meeting for Residential Clothes Dryers and Room Air Conditioners, EERE-2007-BT-STD...

[Thermal energy utilization analysis and energy conservation measures of fluidized bed dryer].

Science.gov (United States)

Xing, Liming; Zhao, Zhengsheng

2012-07-01

To propose measures for enhancing thermal energy utilization by analyzing drying process and operation principle of fluidized bed dryers,in order to guide optimization and upgrade of fluidized bed drying equipment. Through a systematic analysis on drying process and operation principle of fluidized beds,the energy conservation law was adopted to calculate thermal energy of dryers. The thermal energy of fluidized bed dryers is mainly used to make up for thermal consumption of water evaporation (Qw), hot air from outlet equipment (Qe), thermal consumption for heating and drying wet materials (Qm) and heat dissipation to surroundings through hot air pipelines and cyclone separators. Effective measures and major approaches to enhance thermal energy utilization of fluidized bed dryers were to reduce exhaust gas out by the loss of heat Qe, recycle dryer export air quantity of heat, preserve heat for dry towers, hot air pipes and cyclone separators, dehumidify clean air in inlets and reasonably control drying time and air temperature. Such technical parameters such air supply rate, air inlet temperature and humidity, material temperature and outlet temperature and humidity are set and controlled to effectively save energy during the drying process and reduce the production cost.

Electronic air cleaners and the indoor environment

International Nuclear Information System (INIS)

Krafthefer, B.

1986-01-01

The growing awareness over the quality of air in the indoor environment is driving the search for effective control methods for the contaminants of concern. Electronic air cleaners can control such pollutants as dust, pollen, tobacco smoke, radon decay products, and other particulates. This paper presents an examination of the various types of electronic air cleaners and their effects on indoor pollutants. It also examines the mechanism for contaminant removal, the relationship of the efficiency to the characteristics of the contaminant, and what type of contaminants can be controlled with the electronic air cleaner, with particular emphasis placed on the removal of radon decay products. From a study on radon product removal in residences, the electronic air cleaner was found to have an efficiency of up to 70%. Not only was there a reduction in the residential working level, but the fluctuations in the working level were also reduced. With this information, they can better understand how to solve the air treatment problem of the inhabited space. 17 references, 8 figures

Performance of a Forced-Convection Greenhouse Dryer for Fish Drying

Directory of Open Access Journals (Sweden)

Martunis Martunis

2013-04-01

Full Text Available ABSTRACT. This research present experimental performance of a forced convection greenhouse dryer for drying of fish. The greenhouse dryer was installed at Aceh province, Indonesia. It has a concrete floor with the area of 6×4 m2. The roof of dryer is built in semi-cylindrical shape and covered with transparent polycarbonate sheets. Two axial flow fans powered by a 50-watt solar cell module was used to generate forced convection for ventilating the dryer.To investigate its performance, the dryer was used to dry two batches of fish. The Results showed that to dry 50 kg fish with initial moisture 68 % required 11 hours. Incontrast, to dry the same amount of fish using sun drying take a time about 2 days. The air temperature inside greenhouse dryer at noon in the clear day was 45-55°C. Kinerja Pengering Rumah Kaca Dengan Metode Konveksi Paksa Untuk Pengeringan Ikan ABSTRAK. Penelitian ini memperlihatkan hasil percobaan terhadap kinerja pengering rumah kaca dengan metode konveksi udara secara paksa pada pengeringan ikan. Penelitian pengering rumah kaca ini dilakukan di Propinsi Aceh, Indonesia. Pengering ini berlantaikan beton dengan luas sebesar 6x4 m2. .Atapnya dibuat berbentuk semi-selinder dan ditutup dengan lembaran plastik transparan berbahan polikarbonat. Dua buah kipas dengan aliran udara secara aksial dipasang dengan sumber daya berasal dari panel surya sebesar 50 Watt dan dipakai untuk menghasilkan konveksi udara paksa pada ventilasi pengering. Untuk menginvestigasi kinerja rumah kaca ini, pengering ini digunakan untuk mengeringkan dua tumpukan ikan. Hasilnya menunjukkan bahwa untuk mengeringkan sebanyak 50 kg ikan dengan kadar air awalnya sebesar 68% membutuhkan waktu selama 11 jam. Sebaliknya, dengan menggunakan sinar matahari secara langsung, untuk mengeringkan ikan dengan jumlah yang sama, maka waktu yang dibutuhkan lebih lama yaitu sekitar 2 hari. Suhu udara di dalam rumah pengering tepat pada siang hari yang cerah berkisar antara 45

Evaluation of electrolytic alkaline cleaners by evaporative-rate analysis

International Nuclear Information System (INIS)

Hamilton, C.B.

1975-01-01

A method has been developed by which electrolytic alkaline cleaners used in large volumes in steel mills can be evaluated for their ability to clean rolling oil from steel strip without the necessity of large-scale mill trials. The method is evaporative-rate analysis, which can be used to determine the relative amount of residual oil on steel strip after cleaning. The procedure consists in placing a droplet of a solution of a volatile, radioactive, carbon-14 tagged organic compound dissolved in a more volatile solvent, on the surface of the metal, where it forms a ternary solution with any oil on the surface. The amount of oil in this ternary solution affects the rate of evaporation of the tagged compound. The rate of evaporation, monitored by a Geiger-Mueller detector, is a measure of the cleanliness of the surface. A number of commercial alkaline cleaners, both solids and liquids, were evaluated over a range of concentrations. Results indicated that the effectiveness of commercial alkaline cleaners varies greatly, and is a function of the cleaner concentration, cleaner composition, and polarity of cleaning. The presence of antifoaming agents also affects cleaning ability. The results of this study indicate that evaporative-rate analysis is a rapid and effective method for evaluating cleaners

Cementitious Spray Dryer Ash-Tire Fiber Material for Maximizing Waste Diversion

Directory of Open Access Journals (Sweden)

Charles E. Riley

2011-01-01

Full Text Available Spray dryer absorber (SDA material, also known as spray dryer ash, is a byproduct of coal combustion and flue gas scrubbing processes that has self-cementing properties similar to those of class C fly ash. SDA material does not usually meet the existing standards for use as a pozzolan in Portland cement concrete due to its characteristically high sulfur content, and thus unlike fly ash, it is rarely put to beneficial use. This paper presents the results of a study with the objective of developing beneficial uses for SDA material in building materials when combined with tire fiber reinforcement originating from a recycling process. Specifically, spray dryer ash was investigated for use as the primary or even the sole binding component in a mortar or concrete. This study differs from previous research in that it focuses on very high contents of spray dryer ash (80 to 100 percent in a hardened product. The overarching objective is to divert products that are normally sent to landfills and provide benefit to society in beneficial applications.

Hospital trash: cleaners speak of their role in disease prevention.

Science.gov (United States)

Messing, K

1998-06-01

Feminist researchers have contrasted the caring provided by women in hospitals with a more fragmented "curing" approach, which they identify with the predominantly male professions of medicine and surgery. The author spoke with hospital cleaners about their jobs and their health. Several themes emerged: the invisibility of the cleaning function, lack of respect for cleaners, representations of cleaning as undemanding, and assumptions that women's work in cleaning is particularly easy. Cleaners use various strategies to combat these stereotypes but receive little help from administrators or fellow employees. There is a hierarchy in the status of Québec hospital workers with curing (doctors) at the top, followed by caring and healing (nurses, therapists, and attendants), and hygiene (cleaners, sterilizers, and launderers) at the bottom. Authority hierarchies in health care are not related to gender in a simple way, although there is discrimination against women cleaners. The fact that cleaning, especially cleaning performed by women, is invisible to managers, other hospital personnel, and patients has important consequences for cleaners' and for patients' health.

Evaluation of the efficiency of denture cleaners for removing denture adhesives.

Science.gov (United States)

Harada-Hada, Kae; Hong, Guang; Abekura, Hitoshi; Murata, Hiroshi

2016-12-01

We developed a new scoring index for assessing the removability of denture adhesives and evaluated the removal efficiency of denture cleaners. Although our understanding of the importance of denture care is increasing, little is known about the effectiveness and efficiency of denture cleaners on denture adhesives. Therefore, guidelines for proper cleaning are necessary. We used five denture cleaner solutions on two cream adhesives, one powder adhesive and one cushion adhesive. After immersion in the denture cleaners for a designated time, we evaluated the area of the sample plate still covered by denture adhesive. Cream adhesives were removed more completely after immersion in majority of the denture cleaners than in water. Powder adhesive was removed more quickly than cream adhesives. Cushion adhesive was not removed by immersion in either the denture cleaners or water control. Some denture cleaners could liquefy cream adhesives more than water, but these differences were not observed in case of powder and cushion adhesives. © 2015 John Wiley & Sons A/S and The Gerodontology Association. Published by John Wiley & Sons Ltd.

76 FR 971 - Energy Conservation Program for Consumer Products: Test Procedures for Clothes Dryers and Room...

Science.gov (United States)

2011-01-06

.... Detergent Specifications for Clothes Dryer Test Cloth Preconditioning 5. Changes To Reflect Current Usage... conservation standard; (3) updated detergent specifications for clothes dryer test cloth preconditioning; (4... detergent specifications for clothes dryer test cloth preconditioning; (7) update the references to external...

DESIGN AND THERMAL PERFORMANCE OF THE SOLAR BIOMASS HYBRID DRYER FOR CASHEW DRYING

Directory of Open Access Journals (Sweden)

Saravanan Dhanuskodi

2014-12-01

Full Text Available Drying of Cashew nut to remove testa is one of the most energy-intensive processes of cashew nut process industry. For this reason a hybrid dryer consisting of a solar flat plate collector, a biomass heater and a drying chamber is designed and fabricated. 40 kg of Cashew nut with initial moisture of 9 % is used in the experiment. The performance test of the dryer is carried out in two modes of operation: hybrid-forced convection and hybrid-natural convection. Drying time and drying efficiency during these two modes of operation are estimated and compared with the sun drying. The system is capable of attaining drying temperature between 50º and 70ºC. In the hybrid forced drying, the required moisture content of 3% is achieved within 7 hours and the average system efficiency is estimated as 5.08%. In the hybrid natural drying, the required moisture content is obtained in 9 hours and the average system efficiency is 3.17%. The fuel consumption during the drying process is 0.5 kg/hr and 0.75 kg/hr for forced mode and natural mode, respectively. The drying process in the hybrid forced mode of operation is twice faster than the sun drying. The dryer can be operated in any climatic conditions: as a solar dryer on normal sunny days, as a biomass dryer at night time and as a hybrid dryer on cloudy days. Based on the experimental study, it is concluded that the developed hybrid dryer is suitable for small scale cashew nut farmers in rural areas of developing countries.

Heat-pump tumble dryers; Waermepumpen-Tumbler

Energy Technology Data Exchange (ETDEWEB)

Bluemig, N.; Gatter, R.

2004-07-01

Commonly available tumble dryers with air-vented or condenser systems in combination with electrical heating have a high specific energy consumption and never fulfil the requirements for Energy Label Class A (<= 0.55 kWh/kg.). The development of a tumbler with a heat pump system has enabled a reduction of almost 50% in the specific energy consumption. In addition to ecological aspects, this means that a significant reduction in energy costs is achieved as well as a beneficial effect on room climate. Other considerations taken into account in the development of the 6.5 kg tumbler were: (i) Compact modular design; integration of the heat pump in the appliance casing; (ii) Long operating life without clogging-up of the heat exchanger by fluff; (iii) Stable process throughout the drying in ambient temperatures of up to 35 {sup o}C. Process stability in particular presented a tough challenge. The solution came in the form of an additional booster condenser that prevents overheating of the compressor towards the end of the process when only negligible amounts of energy are being carried away as a result of the low residual moisture in the laundry. It proved possible to reduce the specific power consumption to less than 0.4 kWh/kg and the leak rate to less 30 %. Thanks to the compact, modular design, the heat pump could be integrated in a housing which has the same size as a conventional 6.5 kg dryer. Clogging-up of the heat exchanger surfaces with fluff was prevented by a multi-stage cascade filtration system. With this heat pump dryer it has been possible for the very first time to develop to series production and launch an appliance in the up to 6.5 kg category that not only fulfils the requirements of Energy Label Class A but also offers a serious alternative to conventional tumble dryers thanks to its compact design, operating safety and ease of operation. Future development opportunities lie in more cost-effective production of the heat pump module, shortening of

Occupational exposures and health outcomes among Latina hotel cleaners.

Science.gov (United States)

Hsieh, Yu-Chin Jerrie; Apostolopoulos, Yorghos; Hatzudis, Kiki; Sönmez, Sevil

2014-01-01

The poor working conditions of Latina hotel cleaners render them particularly vulnerable to elevated occupational hazards that lead to adverse health outcomes. This article presents a comprehensive review of occupational risks (including physical, chemical, biological, and psychosocial risk factors) and health outcomes (including musculoskeletal disorders, respiratory diseases, dermatological diseases and allergies, and psychological disorders) for Latina hotel cleaners, within their unique sociocultural contexts. Preventive interventions for improving Latina hotel cleaners' work and health conditions are recommended.

Cutting cleaner

International Nuclear Information System (INIS)

Elsen, R.P.H. van; Smits, M.

1991-01-01

This paper presents the results of a long term field test of the Cutting Cleaner, which is used for the treatment of wet oil contaminated cuttings (WOCC) produced when drilling with Oil Based Mud (OBM). It was concluded that it is possible to reduce the oil content of cuttings to an average of 1 - 2%. The recovered base oil can be reused to make new oil based mud

Metal cleaner poisoning

Science.gov (United States)

... do so by poison control or a health care provider. If the chemical is on the skin or in the eyes, flush with lots of water for at least 15 minutes. If the person swallowed the metal cleaner, give them water or milk right away, unless a provider tells you not ...

Epidemiology of occupational injury among cleaners in the healthcare sector.

Science.gov (United States)

Alamgir, Hasanat; Yu, Shicheng

2008-09-01

The cleaning profession has been associated with multiple ergonomic and chemical hazards which elevate the risk for occupational injury. This study investigated the epidemiology of occupational injury among cleaners in healthcare work settings in the Canadian province of British Columbia. Incidents of occupational injury among cleaners, resulting in lost time from work or medical care, over a period of 1 year in two healthcare regions were extracted from a standardized operational database and with person-years obtained from payroll data. Detailed analysis was conducted using Poisson regression modeling. A total of 145 injuries were identified among cleaners, with an annual incidence rate of 32.1 per 100 person-years. After adjustment for age, gender, subsector, facility, experience and employment status, Poisson regression models demonstrated that a significantly higher relative risk (RR) of all injury, musculoskeletal injury and cuts was associated with cleaning work in acute care facilities, compared with long-term care facilities. Female cleaners were at a higher RR of all injuries and contusions than male cleaners. A lower risk of all injury and allergy and irritation incidents among part-time or casual workers was found. Cleaners with >10 years of experience were at significantly lower risk for all injury, contusion and allergy and irritation incidents. Cleaners were found to be at an elevated risk of all injury categories compared with healthcare workers in general.

Metal-Detergent/Cleaner Compatibility

National Research Council Canada - National Science Library

Hindin, Barry

1994-01-01

...) such as CFC-1 13 or 1,1,1 Trichioroethane (TCA) in their cleaning and degreasing procedures. During the last few years, AGMC has been evaluating alternative, environmentally acceptable chemicals to replace their ODC cleaners...

PIV measurements of flow structures in a spray dryer

DEFF Research Database (Denmark)

Meyer, Knud Erik; Velte, Clara Marika; Ullum, Thorvald

2011-01-01

Stereoscopic Particle Image Velocimetry (PIV) measurements are made in horizontal planes in a simplified scale model of a spray dryer using water as fluid. The sample rate was sufficient to resolve phenomena at lower frequencies. Data reveal asymmetric velocity fields in both mean fields and dyna......Stereoscopic Particle Image Velocimetry (PIV) measurements are made in horizontal planes in a simplified scale model of a spray dryer using water as fluid. The sample rate was sufficient to resolve phenomena at lower frequencies. Data reveal asymmetric velocity fields in both mean fields...

Review on advanced of solar assisted chemical heat pump dryer for agriculture produce

International Nuclear Information System (INIS)

Fadhel, M.I.; Sopian, K.; Daud, W.R.W.; Alghoul, M.A.

2011-01-01

Over the past three decades there has been nearly exponential growth in drying R and D on a global scale. Improving of the drying operation to save energy, improve product quality as well as reduce environmental effect remained as the main objectives of any development of drying system. A solar assisted chemical heat pump dryer is a new solar drying system, which have contributed to better cost-effectiveness and better quality dried products as well as saving energy. A solar collector is adapted to provide thermal energy in a reactor so a chemical reaction can take place. This reduces the dependency of the drying technology on fossil energy for heating. In this paper a review on advanced of solar assisted chemical heat pump dryer is presented (the system model and the results from experimental studies on the system performance are discussed). The review of heat pump dryers and solar assisted heat pump dryer is presented. Description of chemical heat pump types and the overview of chemical heat pump dryer are discussed. The combination of chemical heat pump and solar technology gives extra efficiency in utilizing energy. (author)

Enhancement of Energy Efficiency and Food Product Quality Using Adsorption Dryer with Zeolite

Directory of Open Access Journals (Sweden)

Moh Djaeni

2013-06-01

Full Text Available Drying is a basic operation in wood, food, pharmaceutical and chemical industry. Currently, several drying methods are often not efficient in terms of energy consumption (energy efficiency of 20-60% and have an impact on product quality degradation due to the introduction of operational temperature upper 80oC. This work discusses the development of adsorption drying with zeolite to improve the energy efficiency as well as product quality. In this process, air as drying medium is dehumidified by zeolite. As a result humidity of air can be reduced up to 0.1 ppm. So, for heat sensitive products, the drying process can be performed in low or medium temperature with high driving force. The study has been conducted in three steps: designing the dryer, performing laboratory scale equipment (tray, spray, and fluidised bed dryers with zeolite, and evaluating the dryer performance based on energy efficiency and product quality. Results showed that the energy efficiency of drying process is 15-20% higher than that of conventional dryer. In additon, the dryer can speed up drying time as well as retaining product quality.

Usage of Heat Pump Dryer in Food Drying Process and Apple Drying Application

Directory of Open Access Journals (Sweden)

Gökhan Gürlek

2015-12-01

Full Text Available In Turkey, drying is achieved natural method by spreading out the material on the ground. In this way, there are many disadvantages like low quality and hygienic problems. The resulting loss of food quality in the dried products may have effect negatively trade potential and economical worth. For preventing the deterioration of the materials different types of drying methods have been developed. Low energy consumption applications are important for drying industry besides high product quality. For this purpose, heat pump dryer is gaining importance day by day in drying applications. In this study, the working principle of the heat pump dryer, heat pump types in the drying process and the heat pump dryer performance criteria will be considered. An example of application will be described using obtained results from apple drying operation that is conducted in the heat pump dryer.

Cleaner Technology in Denmark - support measures and regulatory efforts

DEFF Research Database (Denmark)

Jørgensen, Ulrik

2005-01-01

Danish cleaner technology support policies have been successful in fostering innovations that reduce the invironmental impact of products and production. But the lack of enforcement support for cleaner technology in environmental permits has limited the overall impact....

Numerical analysis on centrifugal compressor with membrane type dryer

Science.gov (United States)

Razali, M. A.; Zulkafli, M. F.; Mat Isa, N.; Subari, Z.

2017-09-01

Moisture content is a common phenomenon in industrial processes especially in oil and gas industries. This contaminant has a lot of disadvantages which can lead to mechanical failure DEC (Deposition, Erosion & Corrosion) problems. To overcome DEC problem, this study proposed to design a centrifugal compressor with a membrane type dryer to reduce moisture content of a gas. The effectiveness of such design has been analyzed in this study using Computational Fluid Dynamics (CFD) approach. Numerical scheme based on multiphase flow technique is used in ANSYS Fluent software to evaluate the moisture content of the gas. Through this technique, two kind of centrifugal compressor, with and without membrane type dryer has been tested. The results show that the effects of pressure on dew point temperature of the gas change the composition of its moisture content, where high value lead more condensation to occur. However, with the injection of cool dry gas through membrane type dryer in the centrifugal compressor, the pressure and temperature of moisture content as well as mass fraction of H2O in centrifugal compressor show significant reduction.

Conceptual design of pilot scale solar dryer for seaweeds

International Nuclear Information System (INIS)

Marta Abreu de Las Villas (Cuba))" data-affiliation=" (Departamento de Ingeniería Química, Facultad de Química y Farmacia, Universidad Central Marta Abreu de Las Villas (Cuba))" >Roche-Delgado, Liset; Marta Abreu de Las Villas (Cuba))" data-affiliation=" (Departamento de Ingeniería Química, Facultad de Química y Farmacia, Universidad Central Marta Abreu de Las Villas (Cuba))" >Hernández-Touset, Juan Pedro; Marta Abreu de Las Villas (Cuba))" data-affiliation=" (Departamento de Ingeniería Química, Facultad de Química y Farmacia, Universidad Central Marta Abreu de Las Villas (Cuba))" >García-Rodríguez, Agustín

2017-01-01

Drying algal biomass with the use of solar radiation is an economical and environmentally compatible option. The aim of this work was to design an indirect solar dryer with natural air circulation for seaweeds drying. The equipment supports discrete quantities of wet biomass and is protected from environmental situations that may damage the product; it does not need electricity to operate and the construction and operating costs are low. This comprises a collector made of copper plates for air circulation, heated by solar radiation, a glass cover and drying trays with a wooden structure. The dryer was designed to obtain 0, 3 kg / day of dry biomass. The methodology allows construction and operation of a flexible solar dryer in different operating conditions for research on seaweeds. Correspondingly with environmental and operating conditions the design included estimation of drying time, the determination of drying area, number of trays, air flow from the collector to the trays, collector sizing; heat transfer area, temperature reached by air and collector efficiency. (author)

Natural convection solar dryer with biomass back-up heater

Energy Technology Data Exchange (ETDEWEB)

Bena, B.; Fuller, R.J. [University of Melbourne (Australia). Faculty of Engineering

2002-07-01

A direct-type natural convection solar dryer and a simple biomass burner have been combined to demonstrate a drying technology suitable for small-scale processors of dried fruits and vegetables in non-electrified areas of developing countries. From a series of evaluation trials of the system, the capacity of the dryer was found to be 20-22kg of fresh pineapple arranged in a single layer of 0.01-m-thick slices. The overall drying efficiency of the unit was calculated to be {approx} 9%. During the same trial, the drying efficiency of the solar component alone was found to be 22%. Other trials estimated the efficiency of the burner in producing useful heat for drying to be 27%. Key features of the biomass burner were found to be the addition of thermal mass on the upper surface, an internal baffle plate to lengthen the exhaust gas exit path and a variable air inlet valve. Further modifications to further improve the performance of both the solar and biomass components of the dryer are suggested. (author)

Thin layer drying characteristics of curry leaves (Murraya koenigii in an indirect solar dryer

Directory of Open Access Journals (Sweden)

Vijayan Selvaraj

2017-01-01

Full Text Available In this work, the thin layer drying characteristics of curry leaves (Murraya koenigii has been studied in an indirect forced convection solar dryer with constant air mass flow rate of 0.0636 kg/s. Twelve thin layer drying models were tested for its suitability to describe the drying characteristics of curry leaves. The dryer has reduced the initial moisture content of curry leaves from 67.3% (wet basis to the final moisture content of 4.75% (wet basis in 3.5 hours. The pickup efficiency of indirect solar dryer for drying curry leaves was varied between 4.9% and 23.02%. Based on the statistical parameters, the Modified Henderson and Pabis model and Wang and Singh model were selected for predicting the drying characteristics of curry leaves. The payback period for the solar dryer was evaluated as 8 months, which is found to be much lower when compared with the entire life span of 15 years. The payback evaluation confirms that the solar dryer is economically viable in rural applications.

Inhomogeneous electric field air cleaner

International Nuclear Information System (INIS)

Schuster, B.G.

1976-01-01

For applications requiring the filtration of air contaminated with enriched uranium, plutonium or other transuranium compounds, it appears desirable to collect the material in a fashion more amenable to recovery than is now practical when material is collected on HEPA filters. In some instances, it may also be desirable to use an air cleaner of this type to substantially reduce the loading to which HEPA filters are subjected. A theoretical evaluation of such an air cleaner considers the interaction between an electrically neutral particle, dielectric or conducting, with an inhomogeneous electric field. An expression is derived for the force exerted on a particle in an electrode configuration of two concentric cylinders. Equations of motion are obtained for a particle suspended in a laminar flow of air passing through this geometry. An electrical quadrupole geometry is also examined and shown to be inferior to the cylindrical one. The results of two separate configurations of the single cell prototypes of the proposed air cleaner are described. These tests were designed to evaluate collection efficiencies using mono-disperse polystyrene latex and polydisperse NaCl aerosols. The advantages and problems of such systems in terms of a large scale air cleaning facility will be discussed

Design, Development and Performance Evaluation of a Small Scale Solar Assisted Paddy Dryer for on Farm Processing

Directory of Open Access Journals (Sweden)

Sidrah Ashfaq

2016-04-01

Full Text Available With the continued escalation in population growth and the expansion of international food trade and demand of high quality product for food security at low cost has created considerable interest in the development of new post-harvest technologies. This is particularly important for developing countries where post-harvest losses of cereals are between 10-20% and of fruits and vegetables as high as 20- 100% A new solar assisted paddy dryer with central air distribution model (along the length of drying chamber has been developed. Due to this distinct feature of the dryer high drying rate was achieved during the drying processes .Other components of the dryer are perforated drying chamber, blower and flat plat solar air collector. Dryer was evaluated using 100kg of freshly harvested paddy at 23.78% moisture content (wb. Performance evaluation results showed that the mean drying rate of the solar assisted paddy dryer was 0.87kg/hr per for every 100kg, whereas 0.46kg/hr was the sun drying rate comparatively. The faster drying rate of the dryer reveals its suability to dry the paddy for its safe storage moisture content rapidly. By using the solar assisted paddy dryer, approximately 50% saving in time was also achieved as compared with the traditional sun drying method. Solar assisted paddy dryer took 10hr for drying the 100kg paddy up to 14%, while sun drying method dried paddy up to 13.89% in 19 hours. Cost analysis also showed that, by using solar assisted paddy dryer we candry good quality paddy at low cost as compared with the open sun drying method. For development of agriculture in the rural areas, commercial size of the solar assisted paddy dryer can be amplified and produced at community level.

Application of Constrained Linear MPC to a Spray Dryer

DEFF Research Database (Denmark)

Petersen, Lars Norbert; Poulsen, Niels Kjølstad; Niemann, Hans Henrik

2014-01-01

In this paper we develop a linear model predictive control (MPC) algorithm for control of a two stage spray dryer. The states are estimated by a stationary Kalman filter. A non-linear first-principle engineering model is developed to simulate the spray drying process. The model is validated against...... experimental data and able to precisely predict the temperatures, the air humidity and the residual moisture in the dryer. The MPC controls these variables to the target and reject disturbances. Spray drying is a cost-effective method to evaporate water from liquid foods and produces a free flowing powder...

Bioactivity of microencapsulated soursop seeds extract on Plutella xylostella

Directory of Open Access Journals (Sweden)

Ismael Barros Gomes

2016-05-01

Full Text Available ABSTRACT: The aim of this study was to evaluate the bioactivity of microencapsulated extract from the soursop seeds, Annona muricata L. ( Annonaceae , on diamondback moth, Plutella xylostela L. (Lepidoptera: Plutellidae . Microencapsulation was performed in a Mini Spray Dryer model B-290 using 50mL of ethanolic and hexanic extracts plus 150mL of ethanol and 150mL of ultrapure water, mixed with aerosil (first polymer or arabic gum (second polymer. It was possible to microencapsulate the ethanolic extract of soursop seeds only by using the polymer arabic gum at 20%. The microencapsulated extract caused significant acute toxicity (LC50=258mg L-1 and chronic effects, especially reduction of larval viability and increased larval stage. We concluded that the microencapsulation of the ethanolic extract of soursop seeds can be a viable alternative for controlling diamondback moth with possible gains for the environment.

Energetic and economic optimization of solar tunnel dryers with a photovoltaic driven fan

International Nuclear Information System (INIS)

Muehlbauer, W.; Mayer, R.A.; Esper, A.; Reisinger, L.; Linckh, G.; Hensel, O.

1992-02-01

In the recent years the solar tunnel dryer has been used successfully for drying several agricultural products in tropical and subtropical countries. Up to now the dissemination has been limited to electrified areas. Objective of this work has been the improvement of the thermal performance of the tunnel dryer due to a optimization of the plastic film solar air heater as well as optimization work in point of fluid dynamic view to reduce the power requirement of the blower. To improve the efficiency of the blower optimization work had been done by investigating several blower wheels, dc-motors and actuation systems. A PV-System was designed according to these requirements to test the long term behaviour. The remarkable features of the newly designed solar tunnel dryer are the low power requirement for driving the blower and a high efficiency of the actuation. In the range of a power requirement of 80 - 100 W a blower with an efficiency of 48% is now available. The theoretical power requirement of the solar tunnel dryer could be reduced to 11 W. From economic point of view the use of the solar tunnel dryer is possible. (orig.) With 3 refs., 15 tabs., 49 figs [de

A dedicated on-line detecting system for auto air dryers

Science.gov (United States)

Shi, Chao-yu; Luo, Zai

2013-10-01

According to the correlative automobile industry standard and the requirements of manufacturer, this dedicated on-line detecting system is designed against the shortage of low degree automatic efficiency and detection precision of auto air dryer in the domestic. Fast automatic detection is achieved by combining the technology of computer control, mechatronics and pneumatics. This system can detect the speciality performance of pressure regulating valve and sealability of auto air dryer, in which online analytical processing of test data is available, at the same time, saving and inquiring data is achieved. Through some experimental analysis, it is indicated that efficient and accurate detection of the performance of auto air dryer is realized, and the test errors are less than 3%. Moreover, we carry out the type A evaluation of uncertainty in test data based on Bayesian theory, and the results show that the test uncertainties of all performance parameters are less than 0.5kPa, which can meet the requirements of operating industrial site absolutely.

Cleaner technology diffusion: case studies, modeling and policy. Editorial

NARCIS (Netherlands)

Montalvo Corral, C.; Kemp, R.

2008-01-01

The development and application of cleaner technologies (environmental technologies) offer multiple benefits for the adopter: reduced emissions, less waste and cost savings from reduced resource use and savings on waste costs. The question here is: if cleaner technologies offer such great benefits

Critical Point Dryer: Tousimis 916B Series C

Data.gov (United States)

Federal Laboratory Consortium — Description:CORAL Name: Critical Point DryerThis system utilizes CO 2to dry fragile suspended and floating structures Specifications / Capabilities:Wafer size up to...

Self-Compensation of Astigmatism in Mode-Cleaners for Advanced Interferometers

Energy Technology Data Exchange (ETDEWEB)

Barriga, P; Zhao Chunnong; Ju Li; Blair, David G [School of Physics, University of Western Australia, Crawley, WA6009 (Australia)

2006-03-02

Using a conventional mode-cleaner with the output beam taken through a diagonal mirror it is impossible to achieve a non-astigmatic output. The geometrical astigmatism of triangular mode-cleaners for gravitational wave detectors can be self-compensated by thermally induced astigmatism in the mirrors substrates. We present results from finite element modelling of the temperature distribution of the suspended mode-cleaner mirrors and the associated beam profiles. We use these results to demonstrate and present a self-compensated mode-cleaner design. We show that the total astigmatism of the output beam can be reduced to 5x10{sup -3} for {+-}10% variation of input power about a nominal value when using the end mirror of the cavity as output coupler.

Planning of the evaluation of cleaner production experiences in the CEPITA companies

DEFF Research Database (Denmark)

Jørgensen, Michael Søgaard

1998-01-01

The report describes the theoretical and methodological background for the evaluation in 1998 of the cleaner production implementation in a nu,mber of Tanzanian companies taking part in a DANIDA financed cleaner production develeopment project in 1994-95......The report describes the theoretical and methodological background for the evaluation in 1998 of the cleaner production implementation in a nu,mber of Tanzanian companies taking part in a DANIDA financed cleaner production develeopment project in 1994-95...

Biogas utilization for drying sweet potato chips by using infrared dryer

Science.gov (United States)

Sriharti, Rahayuningtyas, Ari; Susanti, Novita Dwi; Sitompul, Rislima Febriani

2017-11-01

This study aims to utilize biogas, that produced from organic waste, as fuel for infrared dryers. The digester was dome type, which made from fiberglass, 5.5 m3 capacities, gas container made from soft PVC, 5.6 m3 capacities. The infrared dryer was household scale which have dimension 2000 mm x 2000 mm x 2000 mm, it is consist of 2 racks, which have size 1500 mm x 500 mm x 1400 mm, and consist of 44 baking pans (600 mm X 400 mm x 30 mm), the dryer has 36 kg of capacity. The parameters observed include ambient temperature, temperature inside the digester, pH value, biogas production, drying room temperature, moisture content of sweet potato and biogas consumption for drying. Infrared dryer is used to dry the sweet potato slices thickness of 2 mm with total amount 12 kg, at room temperature dryer ± 60 °C. The results showed that the average biogas production was 1.335 m3 per day, at a temperature of 26 - 35 °C and the neutral pH value was 6.99 - 7.7. 12 kg of sweet potato sliced dried for 4 hours, the initial moisture content of 79.68 % decreased to 8.98 %, the consumption of biogas used 4,952 m3. The final result of drying process of sweet potato slices of 3.5 kg, there was a shrinkage of 70.83 %. Characterization of sweet potato slices is 3 % protein, 0,6 % fat, 94 % carbohydrate and 2 % ash. These sweet potato can be used as flour for cookies and cake raw materials, the use of sweet potato flour can reach 50 - 100 %.

Research into Noise Generated by Domestic Appliances in the Anechoic Chamber

Directory of Open Access Journals (Sweden)

Agnė Žukauskienė

2012-12-01

Full Text Available Loud noise has a negative impact on the entire body, especially on listening. We can hear daily noise everywhere – in the street, at work or at home. The Department of Environmental Protection of Vilnius Gediminas Technical University has adjusted an anechoic chamber adapted for suppressing sound. Under the above introduced conditions, 15 appliances (5 vacuum cleaners, 5 hair dryers and 5 shaving machines have been tested. Equivalent sound pressure level of the vacuum cleaner has varied from 66 dBA to 83 dBA, that of the hair dryer has made from 64 dBA to 70 dBA and for the shaving machine – from 39 to 56 dBA.Article in Lithuanian

Design, development and performance testing of a new natural convection solar dryer

Energy Technology Data Exchange (ETDEWEB)

Pangavhane, D.R. [K.K. Wagh College of Engineering, Nashik (India). Department of Mechanical Engineering; Sawhney, R.L.; Sarsavadia, P.N. [Devi Ahilya Vishwa Vidhyalaya, Indore (India). School of Energy and Environmental Studies

2002-06-01

Mechanical drying of agricultural products is an energy consuming operation in the post-harvesting technology. Greater emphasis is given to using solar energy sources in this process due to the high prices and shortages of fossil fuels. For these purposes, a new natural convection solar dryer consisting of a solar air heater and a drying chamber was developed. This system can be used for drying various agricultural products like fruits and vegetables. In this study, grapes were successfully dried in the developed solar dryer. The qualitative analysis showed that the traditional drying, i.e. shade drying and open sun drying, dried the grapes in 15 and 7 days respectively, while the solar dryer took only 4 days and produced better quality raisins. (author)

Development of a Mini-Freeze Dryer for Material-Sparing Laboratory Processing with Representative Product Temperature History.

Science.gov (United States)

Obeidat, Wasfy M; Sahni, Ekneet; Kessler, William; Pikal, Michael

2018-02-01

The goal of the work described in this publication was to evaluate a new, small, material-sparing freeze dryer, denoted as the "mini-freeze dryer or mini-FD", capable of reproducing the product temperature history of larger freeze dryers, thereby facilitating scale-up. The mini-FD wall temperatures can be controlled to mimic loading procedures and dryer process characteristics of larger dryers. The mini-FD is equipped with a tunable diode laser absorption spectroscopy (TDLAS) water vapor mass flow monitor and with other advanced process analytical technology (PAT) sensors. Drying experiments were performed to demonstrate scalability to larger freeze dryers, including the determination of vial heat transfer coefficients, K v . Product temperature histories during K v runs were evaluated and compared with those obtained with a commercial laboratory-scale freeze dryer (LyoStar II) for sucrose and mannitol product formulations. When the mini-FD wall temperature was set at the LyoStar II band temperature (- 20°C) to mimic lab dryer edge vials, edge vial drying in the mini-FD possessed an average K v within 5% of those obtained during drying in the LyoStar II. When the wall temperature of the mini-FD was set equal to the central vial product temperature, edge vials behaved as center vials, possessing a K v value within 5% of those measured in the LyoStar II. During both K v runs and complete product freeze drying runs, the temperature-time profiles for the average edge vials and central vial in the mini-FD agreed well with the average edge and average central vials of the LyoStar II.

Steam generator with integral downdraft dryer

Energy Technology Data Exchange (ETDEWEB)

Hochmuth, F.W.

1992-02-01

On June 30, 1989, a financial assistance award was granted by the United State Department of Energy, the purpose of which was to study and evaluate the technical aspect, the economic viability, and commercial possibilities of a new furnace design for burning high moisture cellulose type fuels. The new design is an invention by F.W. Hochmuth, P.Eng. and has received United States Patents Nos. 4,480, 557 and 4,502,397. It was conceived as a method to improve the general operation and efficiency of waste wood burning boilers, to avoid the use of stabilizing fuels such as oil or gas, and to reduce objectionable stack emissions. A further objective was to obtain such benefits at relatively low cost by integrating all new material requirements within the furnace itself thereby avoiding the need for costly external equipment. The proposed integral down-draft dryer avoids the use of external dryer systems that are very expensive, have high power consumption, and require a large amount of maintenance. This document provides the details of this invention.

PERFORMANCE ASSESSMENT OF SOLAR DRYER WITH INDIRECT HEATING

Directory of Open Access Journals (Sweden)

Boryana Brashlyanova

2014-03-01

Full Text Available The performed tests were designed to identify and analyze the parameters of drying in a authors model solar dryer. They to be the basis for constructing of an improved model. Drying was carried out in a pilot model solar dryer with prunes in two cycles. Both samples were run under steady sunshine in outdoor air temperature ranging between 20-22°C in the morning and 33-35°C in the early afternoon hours. Depending on the ambient conditions, the drying temperature was found in the range of 30 to 50°C. The dried samples had a water activity Aw> 0.9, due to which the storage is at -18°C. The duration of the drying process of prunes was inconstant and lasted from 2 to 3 days, depending on the final moisture content of the product and the external temperature, humidity, and intensity of solar radiation. The obtained two products intermediate moisture prunes, in addition to direct human consumption could be used as a base for incorporation into other products. Prunes with intermediate moisture content 40% could be consumed directly at ambient temperature or after freezing and tempering at -6 to -5ºC. Based on the established parameters we are to design and produce an improved solar dryer model that allows better utilization of heat and shortening the process duration.

Development of self-running underwater cleaner for nuclear facilities

International Nuclear Information System (INIS)

Ito, Haruo; Mizutani, Takeshi; Miki, Masamichi

1979-01-01

A self-running underwater cleaner for removing sediment accumulated on the bottoms of water tanks in nuclear power stations by remote operation was developed. This cleaner is used in the state maintaining the shielding effect of water against radiation as water is filled in equipment pits, and by the remote operation using cables, it runs freely in water and sucks bottom sediment. The sediment is transported through a drain hose to a treating facility in a power station, and treated in a lump. The cleaner is composed of the carriage with electric steering wheels and driving wheels and a high head submerged pump. Front and rear suction mouths are provided, and suck sediment with high speed water flow while scraping with rubber boards. The cleaner can be used in the water depth of 7 m, and as the results of practical test, it was confirmed that the decontaminating effect and maneuverability were very good so that the sediment at the corner was scarcely left behind, and the effects of labor saving and the reduction of exposure of employees were large. The fundamental experiments were carried out on the running mechanism, the coefficient of friction in water, and the construction of suction mouth. The trial manufacture of the under water cleaner, the water tank experiment and the test in the Mamaoka No. 1 plant are reported. (Kako, I.)

Development of heat pump and infrared-convective dryer and performance analysis for stale bread drying

International Nuclear Information System (INIS)

Aktaş, Mustafa; Şevik, Seyfi; Aktekeli, Burak

2016-01-01

Highlights: • Investigation of stale bread drying behaviors by developing the HPD and IRD. • New techniques for the HP and IR dryers are proposed and found to be efficient. • Evaluations on potential uses low temperature applications of the dryers were reported. • 35.6% of energy saving was provided by heat recovery device. • The overall system efficiency of HPD was calculated as 13–60%. - Abstract: This experimental study aims to develop a heat pump dryer (HPD) and an infrared dryer (IRD) also the comparative empirical analyses of these two methods and to analyze the drying kinetic of stale bread sliced 15 mm thickness and effectiveness on the drying kinetics of the stale bread of dryers. Dryers have been developed by using different techniques such as heat recovery unit, proportional control (PC) of drying air temperature, simultaneous control of the relative humidity–temperature–air flow rate, water cycle dehumidifier and closed-loop cycle to increase the drying efficiency of industrial drying applications. The highest coefficient of performance of the whole heat pump system (COP_w_s_,_H_P) was calculated as 3.7 and drying efficiencies of the IRD and HPD systems were calculated as 39% and 25%, respectively. When the HPD and IRD systems were compared in terms of drying time and energy consumption, it was observed that the IRD system did not only shortened the drying time up to 69%, but also decreased the energy consumption of the system by 43.2%. Based on the obtained results the effective moisture diffusivity (D_e) was calculated in the range from 8.3 × 10"−"8 to 3.2 × 10"−"7 m"2/s and mass transfer coefficient (h_m) was varied from 1.17 × 10"−"5 to 4.52 × 10"−"5 m/s. It was concluded that both dryers have significant effect in reduction of water content; the relative humidity controlled HPD can be applied efficiently for dryers and the dried stale bread can be reused as bread crumb by food industry.

Development of a Modified Vacuum Cleaner for Lunar Surface Systems

Science.gov (United States)

Toon, Katherine P.; Lee, Steve A.; Edgerly, Rachel D.

2010-01-01

The National Aeronautics and Space Administration (NASA) mission to expand space exploration will return humans to the Moon with the goal of maintaining a long-term presence. One challenge that NASA will face returning to the Moon is managing the lunar regolith found on the Moon's surface, which will collect on extravehicular activity (EVA) suits and other equipment. Based on the Apollo experience, the issues astronauts encountered with lunar regolith included eye/lung irritation, and various hardware failures (seals, screw threads, electrical connectors and fabric contamination), which were all related to inadequate lunar regolith mitigation. A vacuum cleaner capable of detaching, transferring, and efficiently capturing lunar regolith has been proposed as a method to mitigate the lunar regolith problem in the habitable environment on lunar surface. In order to develop this vacuum, a modified "off-the-shelf' vacuum cleaner will be used to determine detachment efficiency, vacuum requirements, and optimal cleaning techniques to ensure efficient dust removal in habitable lunar surfaces, EVA spacesuits, and air exchange volume. During the initial development of the Lunar Surface System vacuum cleaner, systematic testing was performed with varying flow rates on multiple surfaces (fabrics and metallics), atmospheric (14.7 psia) and reduced pressures (10.2 and 8.3 psia), different vacuum tool attachments, and several vacuum cleaning techniques in order to determine the performance requirements for the vacuum cleaner. The data recorded during testing was evaluated by calculating particulate removal, relative to the retained simulant on the tested surface. In addition, optical microscopy was used to determine particle size distribution retained on the surface. The scope of this paper is to explain the initial phase of vacuum cleaner development, including historical Apollo mission data, current state-of-the-art vacuum cleaner technology, and vacuum cleaner testing that has

Cleaner shrimp use a rocking dance to advertise cleaning service to clients.

Science.gov (United States)

Becker, Justine H A; Curtis, Lynda M; Grutter, Alexandra S

2005-04-26

Signals transmit information to receivers about sender attributes, increase the fitness of both parties, and are selected for in cooperative interactions between species to reduce conflict [1, 2]. Marine cleaning interactions are known for stereotyped behaviors [3-6] that likely serve as signals. For example, "dancing" and "tactile dancing" in cleaner fish may serve to advertise cleaning services to client fish [7] and manipulate client behavior [8], respectively. Cleaner shrimp clean fish [9], yet are cryptic in comparison to cleaner fish. Signals, therefore, are likely essential for cleaner shrimp to attract clients. Here, we show that the yellow-beaked cleaner shrimp [10] Urocaridella sp. c [11] uses a stereotypical side-to-side movement, or "rocking dance," while approaching potential client fish in the water column. This dance was followed by a cleaning interaction with the client 100% of the time. Hungry cleaner shrimp, which are more willing to clean than satiated ones [12], spent more time rocking and in closer proximity to clients Cephalopholis cyanostigma than satiated ones, and when given a choice, clients preferred hungry, rocking shrimp. The rocking dance therefore influenced client behavior and, thus, appears to function as a signal to advertise the presence of cleaner shrimp to potential clients.

Slurry spray distribution within a simulated laboratory scale spray dryer

International Nuclear Information System (INIS)

Bertone, P.C.

1979-01-01

It was found that the distribution of liquid striking the sides of a simulated room temperature spray dryer was not significantly altered by the choice of nozles, nor by a variation in nozzle operating conditions. Instead, it was found to be a function of the spray dryer's configuration. A cocurrent flow of air down the drying cylinder, not possible with PNL's closed top, favorably altered the spray distribution by both decreasing the amount of liquid striking the interior of the cylinder from 72 to 26% of the feed supplied, and by shifting the zone of maximum impact from 1.0 to 1.7 feet from the nozzle. These findings led to the redesign of the laboratory scale spray dryer to be tested at the Savannah River Plant. The diameter of the drying chamber was increased from 5 to 8 inches, and a cocurrent flow of air was established with a closed recycle. Finally, this investigation suggested a drying scheme which offers all the advantages of spray drying without many of its limitations

16 CFR 501.3 - Replacement bags for vacuum cleaners.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Replacement bags for vacuum cleaners. 501.3... REQUIREMENTS AND PROHIBITIONS UNDER PART 500 § 501.3 Replacement bags for vacuum cleaners. Replacement bags for..., provided: (a) The quantity of contents is expressed in terms of numerical count of the bags; (b) A...

Reputation management promotes strategic adjustment of service quality in cleaner wrasse.

Science.gov (United States)

Binning, Sandra A; Rey, Olivia; Wismer, Sharon; Triki, Zegni; Glauser, Gaétan; Soares, Marta C; Bshary, Redouan

2017-08-21

Adjusting one's behaviour in response to eavesdropping bystanders is considered a sophisticated social strategy, yet the underlying mechanisms are not well studied. Cleaner wrasse, Labroides dimidiatus, cooperate by eating ectoparasites off "client" fishes, or cheat (i.e. bite) and eat client mucus. Image scoring by bystander clients generally causes cleaners from socially-complex (i.e. high cleaner and client abundance; high client species richness) habitats to increase levels of cooperation. However, some individuals may periodically provide tactile stimulation to small resident clients, which attract bystanders close that are bitten, a form of tactical deception. Cortisol injection can reproduce this pattern. Here, we tested whether cleaners from socially-complex versus simple habitats respond differently to cortisol injections in terms of their cleaning interactions with clients. We found that only cleaners from the socially-complex habitat respond to cortisol injection with strategies functioning as tactical deception: i.e. increased tactile stimulation to small clients and increased cheating of large clients relative to small ones. At the socially-simple site, where reputation management is less important, cortisol-treated fish increased their overall levels of cheating, especially of small clients. Thus, strategic adjustments to cooperative behaviour and tactical deception are likely context-dependent, forming part of general reputation management abilities in cleaner wrasse.

Development of an air knife to remove seed coat fragments during lint cleaning

Science.gov (United States)

An air knife is a tool commonly used to blow off debris in a manufacturing line. The knife may also be used to break the attachment force between a lint cleaner saw and a seed coat fragment (SCF) with attached fiber, and remove them. Work continued on evaluating an auxiliary air knife mounted on t...

COREXIT 9580 shoreline cleaner: Development, application, and status

International Nuclear Information System (INIS)

Canevari, G.P.; Fiocco, R.J.; Lessard, R.R.; Fingas, M.

1995-01-01

This paper will describe research on chemical beach cleaners for treatment of oiled shorelines that was initiated in support of the cleaning activities in Prince William Sound (PWS) following the Valdez oil spill in March 1989. The concept for using beach cleaners for shoreline cleanup is to apply a pre-soak to the weathered crude oil on shore and then flush with sea water to wash the oil into a boomed area for subsequent recovery. Criteria imposed on the use of chemical beach cleaners for the cleanup of the Valdez spill were: (1) effective rock cleaning agents should have very little or no toxicity to marine and terrestrial life, (2) there should be no dispersion of the oil washed from the shoreline into the water column; oil was to be recovered by techniques such as skimming or sorbents, and (3) the agents should be on the EPA National Contingency Plan (NCP) list. A laboratory-scale rock washing test was developed to measure cleaner effectiveness and dispersion. A large number of commercially available formulated products were evaluated, as well as development formulations. The commercial products included all of the available NCP-listed products which could function as cleaners. None of the commercial products completely satisfied all the requirements established by the agencies for beach cleaning. However, a new formula, called COREXIT 9580, consisting of two surfactants and a solvent was developed. It exhibited low fish toxicity, low dispersancy and effective rock cleaning capability. The paper reviews the laboratory and field testing to explore the potential use of the COREXIT 9580 to save and restore oiled vegetation

Cleaner products : new tools, players and relationships

DEFF Research Database (Denmark)

Remmen, Arne

focus in the Product Oriented Environmental Initiative. The purpose of this evaluation has been to assess experience from the initiatives to date against the intentions of the action plan, and to provide constructive input to help flesh out a future product-oriented initiative, including the activities...... linked to the new programme for cleaner products. The evaluation has focused on three selected sectors and on inter-sector product-oriented projects carried out under the Action Plan for Cleaner Technology 1993-97. The investigation has been carried out at the request of the Council for Recycling...

Performance Analysis of a Solar Dryer Equipped with a Recycling Air System and Desiccant Chamber

Directory of Open Access Journals (Sweden)

M.H Aghkhani

2013-09-01

Full Text Available Drying is a high energy consuming process. Solar drying is one of the most popular methods for dehydration of agricultural products. In the present study, the performance of a forced convection solar dryer equipped with recycling air system and desiccant chamber was investigated. The solar dryer is comprised of solar collector, drying chamber, silica jell desiccant chamber, air ducts, fan and measuring and controlling system. Drying rate and energy consumption in three levels of air temperature (40, 45 and 50 oC and two modes of drying (with recycling air and no-recycling with open duct system were measured and compared. The results showed that increasing the drying air temperature decreased the drying time and increased the energy consumption in the mode of non-recycling air system. The dryer efficiency and drying rate were better in the mode of recycling air system than open duct system. The highest dryer efficiency was obtained from drying air temperature of 50 oC and the mode of recycling air system. In general, the efficiency of solar collector and the highest efficiency of the dryer were 0.34 and 0.41, respectively.

Performance of a chevron steam dryer for removal of lead-bismuth droplets

International Nuclear Information System (INIS)

Dostal, Vaclav; Yusibani, Elin; Takahashi, Minoru

2005-01-01

An analysis was performed of a chevron type steam dryer with a trap for the removal of lead-bismuth droplets from steam leaving the Water Boiling Direct Contact Lead or Lead-Bismuth Cooled Reactor. The Lagrangian method was used and is described here. The steam flow field was developed using a CFD code FrontFlow/Red. The simulated dryer performance results were compared to a simple theoretical model from literature. The simulation shown that droplets down to 6 microns in diameter can be completely removed by the steam dryer, which is better than reported earlier in literature. A discrepancy with the theoretical model was found for larger droplets (5 to 10 microns in diameter), where the theoretical model predicted lower removal efficiency. The discrepancy is attributed to be installation of the trap, which is not included in this theoretical model. Some droplets of 1 and 0.5 microns were removed in the dryer as well, which indicates the potential for the fine droplet removal if the trap design is carefully optimized. The investigation of the effect of initial droplet velocity shown that the removal efficiency increases with the increase of the positive velocity components. For larger droplets the effect of initial velocity was found to be minuscule. (author)

Performance studies of solar tunnel dryer for drying aonla (Embilica Officinalis) pulp

International Nuclear Information System (INIS)

Seveda, M. S.

2012-01-01

A solar tunnel dryer was constructed and evaluated the performance for drying aonla pulp. The dryer consists of a transparent UV stabilized plastic covered solar collector cum drying unit. Evaluation parameters are air temperature, solar insolation, moisture content, relative humidity and airflow rate. A minimum of 111.18 m 2 solar collector area is required to dry a batch 1000 kg aonla pulp in 16 hours (two days drying period). The initial and final moisture content considered were 424.93 and 10.08% dry basis, respectively. It was observed that on an average 43 per cent of higher temperature was obtained in solar tunnel dryer over the ambient temperature. The results obtained during the test period denoted that the maximum gained energy occurred at 13 o'clock hour and then gradually declined since the maximum solar radiation occurred at this time. (author)

Tritium isotopic exchange in air detritiation dryers

International Nuclear Information System (INIS)

Everatt, A.E.; Johnson, R.E.; Senohrabek, J.A.; Shultz, C.M.

1989-02-01

Isotopic exchange between tritiated and non-tritiated water species in a molecular sieve bed has been demonstrated. At high humidities (+6 degrees Celsius dew point) the rate of tritium isotopic exchange in a 2.4 L molecular sieve bed has been demonstrated to be at least 50% of published exchange rates. In an industrial-sized air detritiation dryer, utilizing the pretreatment technique of H 2 O steam washing to elute the residual tritium, a DF of 12 600 has been demonstrated when operating at an inlet vapor tritium concentration of 14 Ci/kg and at inlet and outlet dew points of 4.8 and -54 degrees Celsius, respectively. In the NPD dryer bed studied, which was not optimally designed for full benefit from isotopic exchange, at least one order of magnitude in additional detritiation is attributed to isotopic exchange in the unsaturated zone. The technique of eluting the residual tritium from an industrial sized bed by H 2 O washing at high temperature, high humidity and low bed loading has been demonstrated to be a fast and effective way of removing tritium from a molecular sieve bed during regeneration. The isotopic exchange model accurately predicted the exchange between tritiated and non-tritiated water species in a molecular sieve bed where there is no net adsorption or desorption. The model's prediction of the tritium breakthrough trend observed in the NPD tests was poor; however, a forced fit can be achieved if the exchange rates in the MTZ and the unsaturated zone are manipulated. More experiments are needed to determine the relative rates of tritium exchange in the saturated, mass transfer, and unsaturated zones of a dryer bed

A study of particle motion in rotary dryer

Directory of Open Access Journals (Sweden)

M. H. Lisboa

2007-09-01

Full Text Available The purpose of this work was to study the performance of a rotary dryer in relation to number of flights. In this work an equationing was proposed to calculate the area used by the solids in two-segment flights of with any angle between the segments. From this area, the flight holdup and the length of fall of the particles were calculated for different angle positions and the results obtained were compared to experimental values. The results show an increase in dryer efficiency with the increase in number of flights up to a limit value, for ideal operational conditions. The experimental data on average residence time were compared to results obtained by calculations using equations proposed in the literature. The equation proposed for predicting flight holdup and length of fall of particles generated very accurate estimations.

Performance of a solar dryer using hot air from roof-integrated solar collectors for drying herbs and spices

Energy Technology Data Exchange (ETDEWEB)

Janjai, S.; Tung, P. [Silpakorn University, Pathom (Thailand). Dept. of Physics

2005-11-01

A solar dryer for drying herbs and spices using hot air from roof-integrated solar collectors was developed. The dryer is a bin type with a rectangular perforated floor. The bin has a dimension of 1.0 m x 2.0 m x 0.7 m. Hot air is supplied to the dryer from fiberglass-covered solar collectors, which also function as the roof of a farmhouse. The total area of the solar collectors is 72 m{sup 2}. To investigate its performance, the dryer was used to dry four batches of rosella flowers and three batches of lemon-grasses during the year 2002-2003. The dryer can be used to dry 200 kg of rosella flowers and lemon-grasses within 4 and 3 days, respectively. The products being dried in the dryer were completely protected from rains and insects and the dried products are of high quality. The solar air heater has an average daily efficiency of 35% and it performs well both as a solar collector and a roof of a farmhouse. (author)

Study on effectiveness of continuous solar dryer integrated with desiccant thermal storage for drying cocoa beans

Directory of Open Access Journals (Sweden)

Sari Farah Dina

2015-03-01

Full Text Available The main objective is to assess effectiveness of continuous solar dryer integrated with desiccant thermal storage for drying cocoa beans. Two type of desiccants were tested, molecular sieve 13× (Na86 [(AlO286·(SiO2106]·264H2O as an adsorbent type and CaCl2 as an absorbent type. The results revealed that during sunshine hours, the maximum temperature within the drying chamber varied from 40 °C to 54 °C. In average, it was 9–12 °C higher than ambient temperature. These temperatures are very suitable for drying cocoa beans. During off-sunshine hours, humidity of air inside the drying chamber was lower than ambient because of the desiccant thermal storage. Drying times for intermittent directs sun drying, solar dryer integrated with adsorbent, and solar dryer integrated with absorbent were 55 h, 41 h, and 30 h, respectively. Specific energy consumptions for direct sun drying, solar dryer integrated with adsorbent, and solar dryer integrated with absorber were 60.4 MJ/kg moist, 18.94 MJ/kg moist, and 13.29 MJ/kg moist, respectively. The main conclusion can be drawn here is that a solar dryer integrated with desiccant thermal storage makes drying using solar energy more effective in term of drying time and specific energy consumption.

Opportunities application of cleaner production practices in paint industry

International Nuclear Information System (INIS)

Mohammed, Y. S. Y.

2010-08-01

There are releases of volatile organic compounds VOC from paint manufacturing process steps and from cleaning operations in El Mohandas Paint Factory. These emission can cause health, safety and productivity problems in the work area. Hence cleaner production application is necessary in this case. Some of the manufacturing processes and equipment used to accomplish these manufacturing are analyzed and generate cleaner production opportunities, implement some of cleaner production solutions of VOC emission control by some of the methods used by paint facilities in reducing emissions. It was found that there is no control available for emissions factors in paints manufacturing process, so that VOC emission based on raw material consumption rather than calculation emission from processes or equipment by alternative method. (Author)

Application of new pre-isolation techniques to mode cleaner design

Energy Technology Data Exchange (ETDEWEB)

Barriga, Pablo [School of Physics, University of Western Australia, Crawley, WA 6009 (Australia); Woolley, Andrew [School of Physics, University of Western Australia, Crawley, WA 6009 (Australia); Zhao Chunnong [Computer and Information Science, Edith Cowan University, Mount Lawley, WA 6050 (Australia); Blair, David G [School of Physics, University of Western Australia, Crawley, WA 6009 (Australia)

2004-03-07

Two very low frequency pre-isolation stages can greatly reduce the residual motion of suspended optical components. In a mode cleaner this can reduce the control forces required on the mirrors, simplifying lock acquisition and reducing noise injection through control forces. This paper describes a 12 m triangular suspended mode cleaner under construction for the AIGO high optical power interferometer. A novel and very compact multistage isolator supports the cavity mirrors. It combines an inverse pendulum in series with a low-mass Roberts linkage, both with pendulum frequencies below 0.1 Hz. The suspension chain is connected to the Roberts linkage via a Euler spring stage and a cantilever spring assembly for vertical isolation. We present an analysis of the mode cleaner, emphasizing the advantage of the improved mode-cleaner suspension and its power-handling capability. The effect of seismic noise on the residual velocity of the mirrors and the predicted frequency stability of the optical cavity are presented.

Application of new pre-isolation techniques to mode cleaner design

International Nuclear Information System (INIS)

Barriga, Pablo; Woolley, Andrew; Zhao Chunnong; Blair, David G

2004-01-01

Two very low frequency pre-isolation stages can greatly reduce the residual motion of suspended optical components. In a mode cleaner this can reduce the control forces required on the mirrors, simplifying lock acquisition and reducing noise injection through control forces. This paper describes a 12 m triangular suspended mode cleaner under construction for the AIGO high optical power interferometer. A novel and very compact multistage isolator supports the cavity mirrors. It combines an inverse pendulum in series with a low-mass Roberts linkage, both with pendulum frequencies below 0.1 Hz. The suspension chain is connected to the Roberts linkage via a Euler spring stage and a cantilever spring assembly for vertical isolation. We present an analysis of the mode cleaner, emphasizing the advantage of the improved mode-cleaner suspension and its power-handling capability. The effect of seismic noise on the residual velocity of the mirrors and the predicted frequency stability of the optical cavity are presented

Quantitative real-time monitoring of dryer effluent using fiber optic near-infrared spectroscopy.

Science.gov (United States)

Harris, S C; Walker, D S

2000-09-01

This paper describes a method for real-time quantitation of the solvents evaporating from a dryer. The vapor stream in the vacuum line of a dryer was monitored in real time using a fiber optic-coupled acousto-optic tunable filter near-infrared (AOTF-NIR) spectrometer. A balance was placed in the dryer, and mass readings were recorded for every scan of the AOTF-NIR. A partial least-squares (PLS) calibration was subsequently built based on change in mass over change in time for solvents typically used in a chemical manufacturing plant. Controlling software for the AOTF-NIR was developed. The software collects spectra, builds the PLS calibration model, and continuously fits subsequently collected spectra to the calibration, allowing the operator to follow the mass loss of solvent from the dryer. The results indicate that solvent loss can be monitored and quantitated in real time using NIR for the optimization of drying times. These time-based mass loss values have also been used to calculate "dynamic" vapor density values for the solvents. The values calculated are in agreement with values determined from the ideal gas law and could prove valuable as tools to measure temperature or pressure indirectly.

THE EFFECT OF THE THICKNESS OF A PACKED BED ON THE DYNAMIC AND THERMAL BEHAVIOR OF A SOLAR DRYER

Directory of Open Access Journals (Sweden)

S KHALDI

2015-06-01

Full Text Available Drying food in the sun is a safe, easy and economical way to preserve food, especially fruits. Cabinet dryers are the most popular equipment for fruit drying. Because of intermittent nature of solar energy, storage is required for uninterrupted supply in order to match the needs. The main objective of this study is to assess effectiveness of continuous solar dryer integrated with packed bed as thermal storage with natural airflow for drying figs (Ficuscarica. The cabinet dryer were envisaged theoretically (computational fluid dynamics (CFD. The distribution of the velocity and temperature of air within the solar dryer were presented during one day of August and under the climate conditions of Tlemcen (Algeria.  The effects of presence of a packed bed on the distribution of velocity and temperature of airflow and on the temperature of figs were analyzed. The results show that the solar dryer design, incorporating a packed bed enhances the capabilities and performance of the solar dryer, through increasing time of drying.

Learning sustainability by developing a solar dryer for microalgae retrieval

Directory of Open Access Journals (Sweden)

Benedita Malheiro

2016-01-01

Full Text Available Excessive fossil fuel consumption is driving the search for alternative energy production solutions and, in particular, for sustainable sources of energy such as microalgae, from which biodiesel, among other useful compounds, can be obtained. After producing the microalgae, they must be harvested and dried. Existing drying solutions consume too much energy and are, therefore, expensive and unsustainable. The goal of this EPS@ISEP Spring 2013 project was to develop a solar microalgae dryer for the microalgae laboratory of ISEP. A multinational team of five students from distinct fields of study was responsible for designing and building the solar microalgae dryer prototype. The prototype includes a control system to ensure that the microalgae are not destroyed during the drying process. The solar microalgae dryer works as a distiller, extracting the excess water from the microalgae suspension. This paper details the design steps, the building technologies, the ethical and sustainable concerns and compares the prototype with existing solutions. The proposed sustainable microalgae drying process is competitive as far as energy usage is concerned. Finally, the project contributed to increase the team’s sustainable development awareness, active learning and motivation.

An overview of cleaner fish use in Ireland.

Science.gov (United States)

Bolton-Warberg, M

2017-11-21

Sea lice infestations represent one of the most significant challenges facing the salmon farming industry, giving rise to lost production, additional costs of treatment and potential negative interactions with wild stocks. At present, cleaner fish, which actively remove lice from salmon, are an effective, biological, long-term option which has been adopted by many countries. In Ireland, several key studies were conducted in the 1990s on the use of wild-caught wrasse (corkwing, goldsinny and rock cook) as cleaner fish in experimental and commercial scale trials. More recently, the National University of Ireland Galway (NUIG), at their marine research facility in Carna (CRS), has undertaken applied research on ballan wrasse and lumpsucker. Currently, CRS is providing lumpsucker juveniles and research and development for the Irish salmon industry with support from BIM (Ireland's Seafood Development Agency) and Marine Harvest Ireland. There is a large amount of research currently being carried out in this area in all countries that are utilizing cleaner fish technology. The current focus in Ireland is the development of a native lumpsucker broodstock to facilitate its sustainable production. The aim of this article was to provide an overview of the research, challenges and use of cleaner fish in Ireland. © 2017 The Authors Journal of Fish Diseases Published by John Wiley & Sons Ltd.

Nuclear criticality safety calculations for a K-25 site vacuum cleaner

International Nuclear Information System (INIS)

Shor, J.T.; Haire, M.J.

1997-02-01

A modified Nilfisk model GSJ dry vacuum cleaner is used throughout the K-25 Site to collect dry forms of highly enriched uranium (HEU). When vacuuming, solids are collected in a cyclone-type separator vacuum cleaner body. Calculations were done with the SCALE (KENO V.a) computer code to establish conditions at which a nuclear criticality event might occur if the vacuum cleaner was filled with fissile solution. Conditions evaluated included full (12-in. water) reflection and nominal (1-in. water) reflection, and full (100%) and 20% 235 U enrichment. Validation analyses of SCALE/KENO and the SCALE 27-group cross sections for nuclear criticality safety applications indicate that a calculated k eff + 2σ eff + 2σ ≥ 0.9605 is considered unsafe and may be critical. Critical conditions were calculated to be 70 g U/L for 100% 235 U and full 12-in. water reflection. This corresponds to a minimum critical mass of approximately 1,400 g 235 U for the approximate 20.0-L volume of the vacuum cleaner. The actual volume of the vacuum cleaner is smaller than the modeled volume because some internal materials of construction were assumed to be fissile solution. The model was an overestimate, for conservatism, of fissile solution occupancy. At nominal reflection conditions, the critical concentration in a vacuum cleaner full of UO 2 F 2 solution was calculated to be 100 g 235 U/L, or 2,000 g mass of 100% 235 U. At 20% 235 U for the 20.0-L volume of the vacuum cleaner. At 15% 235 U enrichment and full reflection, critical conditions were not reached at any possible concentration of uranium as a uranyl fluoride solution. At 17.5% 235 U enrichment, criticality was reached at approximately 1,300 g U/L which is beyond saturation at 25 C

Field measurements of temperature profile for floatovoltaic dryer in the tropics

Science.gov (United States)

Osman, F. A.; Ya'acob, M. E.; Iskandar, A. Noor

2017-09-01

Most of the equator region in a tropical climate zone experiences hot and humid weather but sometimes heavy rain and thunderstorms which occur stochastically in monsoon season. Sunlight which is the energy source can be harvested approximately 8 hours (on average basis) daily throughout the year which leads to the promotion of Solar PV technologies. This works projects the field performance for a new Floatovoltaic Dryer prototype with flexible PV roofing structures covering the top of the dryer system. The field measurements are collected on the lake of Engineering Faculty, UPM supported with 4-parameter weather station. Temperature profile with RH measurements inside the Floatovoltaic Dryer compartments as compared to direct-sun drying mechanism are the main contributions of this work and it projects more than 12 W of convection heat energy could be harvested by using the clean system. The field measurements imply various points of thermocouple and humidity sensor throughout the experiment. Temperature and humidity will be the main elements recorded to analyze the differences under monocrystalline PV panel as compared to natural drying.

DEVELOPMENT OF VACUUM SUBLIMATION DRYERS USING THERMOELECTRIC MODULES

Directory of Open Access Journals (Sweden)

R. A. Barykin

2014-01-01

Full Text Available Summary. The main directions of use of freeze-dryed products and ingredients are revealed. The analysis of sales markets of freeze-dryed products is provided. It is shown that introduction of innovative production technologies will allow to develop dynamically not only to the large companies, but also small firms that will create prerequisites for growth of the Russian market of freeze-dryed products. Tendencies of development of the freeze-drying equipment are analysed. Relevance of development of energy saving freeze-dryers is proved The integrated approach to creation of competitive domestic technologies and the equipment for sublimation dehydration of thermolabile products consists in use of the effective combined remedies of a power supply, a process intensification, reduction of specific energy consumption and, as a result, decrease in product cost at achievement of high quality indicators. Advantages of thermoelectric modules as alternative direction to existing vapor-compression and absorbing refrigerating appliances are given. Researches of process of freeze-drying dehydration with use of thermoelectric modules are conducted. It is scientifically confirmed, that the thermoelectric module working at Peltier effect, promotes increase in refrigerating capacity due to use of the principle of the thermal pump. Options of use of thermoelectric modules in designs of dryers are offered. Optimum operating modes and number of modules in section are defined. Ways of increase of power efficiency of freeze-dryers with use of thermoelectric modules are specified. The received results will allow to make engineering calculations and design of progressive freeze-drying installations with various ways of a power supply.

Development and performance evaluation of a locally fabricated portable solar tunnel dryer for drying of fruits, vegetables and medicinal plants

International Nuclear Information System (INIS)

Munir, A.; Sultan, U.; Iqbal, M.

2013-01-01

The research was conducted to fabricate and develop a portable solar tunnel dryer (STD) for the drying of fruits, vegetables and medicinal plants. The system was designed as a portable system for decentralized applications at various sites to satisfy the drying requirements of small farmers and co-operatives. The cross sectional area of the solar tunnel dryer was trapezoidal in shape having 0.254 m/sup 2/ face area, with length and width of three meters and one meter respectively. It comprises a collector section (1.35 m) long and a drying section (1.65 m long) and two PV powered DC fans to provide the required air flow rate over the perishable agricultural products to be dried. Transparent polythene cover was used to close the dryer on top side to maintain the steady state air flow within the dryer. It has been observed that the drying air temperature was easily raised by some 8-14 degree C above the ambient temperature at air velocity ranges 0-1 m s/sup -1/. The efficiency of the solar tunnel dryer was found to be 40-45%. Psychrometric analysis was also carried out within the dryer and the process curves were drawn. The process curves were found similar to a conventional dryer showing that this dryer can be successfully utilized for the drying of agricultural products using solar energy. (author)

The effect of dryer load on freeze drying process design.

Science.gov (United States)

Patel, Sajal M; Jameel, Feroz; Pikal, Michael J

2010-10-01

Freeze-drying using a partial load is a common occurrence during the early manufacturing stages when insufficient amounts of active pharmaceutical ingredient (API) are available. In such cases, the immediate production needs are met by performing lyophilization with less than a full freeze dryer load. However, it is not obvious at what fractional load significant deviations from full load behavior begin. The objective of this research was to systematically study the effects of variation in product load on freeze drying behavior in laboratory, pilot and clinical scale freeze-dryers. Experiments were conducted with 5% mannitol (high heat and mass flux) and 5% sucrose (low heat and mass flux) at different product loads (100%, 50%, 10%, and 2%). Product temperature was measured in edge as well as center vials with thermocouples. Specific surface area (SSA) was measured by BET gas adsorption analysis and residual moisture was measured by Karl Fischer. In the lab scale freeze-dryer, the molar flux of inert gas was determined by direct flow measurement using a flowmeter and the molar flux of water vapor was determined by manometric temperature measurement (MTM) and tunable diode laser absorption spectroscopy (TDLAS) techniques. Comparative pressure measurement (capacitance manometer vs. Pirani) was used to determine primary drying time. For both 5% mannitol and 5% sucrose, primary drying time decreases and product temperature increases as the load on the shelves decreases. No systematic variation was observed in residual moisture and vapor composition as load decreased. Further, SSA data suggests that there are no significant freezing differences under different load conditions. Independent of dryer scale, among all the effects, variation in radiation heat transfer from the chamber walls to the product seems to be the dominant effect resulting in shorter primary drying time as the load on the shelf decreases (i.e., the fraction of edge vials increases).

Psychosocial work factors and shoulder pain in hotel room cleaners.

Science.gov (United States)

Burgel, Barbara J; White, Mary C; Gillen, Marion; Krause, Niklas

2010-07-01

Hotel room cleaners have physically demanding jobs that place them at high risk for shoulder pain. Psychosocial work factors may also play a role in shoulder pain, but their independent role has not been studied in this group. Seventy-four percent (941 of 1,276) of hotel room cleaners from five Las Vegas hotels completed a 29-page survey assessing health status, working conditions, and psychosocial work factors. For this study, 493 of the 941 (52%) with complete data for 21 variables were included in multivariate logistic regression analyses. Fifty-six percent reported shoulder pain in the prior four weeks. Room cleaners with effort-reward imbalance (ERI) were three times as likely to report shoulder pain (OR 2.99, 95% CI 1.95-4.59, P = 0.000) even after adjustment for physical workload and other factors. After adjustment for physical workload, job strain and iso-strain were not significantly associated with shoulder pain. ERI is independently associated with shoulder pain in hotel room cleaners even after adjustment for physical workload and other risk factors. 2010 Wiley-Liss, Inc.

TESTING ANTIMICROBIAL CLEANER EFFICACY ON GYPSUM WALLBOARD CONTAMINATED WITH STACHYBOTRYS CHARTARUM

Science.gov (United States)

Reducing occupant exposure to indoor mold growth is the goal of this research, through the efficacy testing of antimicrobial cleaners. Often mold contaminated building materials are not properly removed, but instead surface cleaners are applied in an attempt to alleviate the prob...

ENERGY STAR Certified Room Air Cleaners

Data.gov (United States)

U.S. Environmental Protection Agency — Certified models meet all ENERGY STAR requirements as listed in the Version 1.2 ENERGY STAR Program Requirements for Room Air Cleaners that are effective as of July...

Feasibility analysis of heat pump dryer to dry hawthorn cake

International Nuclear Information System (INIS)

Wang, D.C.; Zhang, G.; Han, Y.P.; Zhang, J.P.; Tian, X.L.

2011-01-01

Highlights: → A heat pump dryer (HPD) is effectively proposed to dry hawthorn cake-likely materials. → Low drying temperature and high COP of heat pump are obtained in drying beginning. → HPD is more effective, economic than a traditional hot air dryer. → Feasibility of the HPD is also validated by the operation economy estimation. - Abstract: A heat pump dryer (HPD) would be an economic, environmentally friendly, hygienic drying machine used to dry some food, such as hawthorn cakes. Based on the production process of the hawthorn cake, a HPD is proposed and its basic principle is introduced. The experimental drying curves of the hawthorn cake using the heat pump drying method and the traditional hot air drying method are compared and analyzed. The drying process of hawthorn cakes is similar to that of the other drying materials. The higher drying temperature causes a faster drying process. But in the initial stage of the heat pump drying process, the water content of the hawthorn cake is not sensitive to the drying temperature, so a lower drying air temperature can be available in order to get a higher coefficient of performance (COP) of the heat pump (HP). The experimental results and the economic analysis indicate that the HPD is feasibly used to dry hawthorn cakes.

Feasibility analysis of heat pump dryer to dry hawthorn cake

Energy Technology Data Exchange (ETDEWEB)

Wang, D.C., E-mail: wdechang@163.com [College of Electromechanical Engineering, Qingdao University, Qingdao 266071 (China); Zhang, G.; Han, Y.P.; Zhang, J.P.; Tian, X.L. [College of Electromechanical Engineering, Qingdao University, Qingdao 266071 (China)

2011-08-15

Highlights: {yields} A heat pump dryer (HPD) is effectively proposed to dry hawthorn cake-likely materials. {yields} Low drying temperature and high COP of heat pump are obtained in drying beginning. {yields} HPD is more effective, economic than a traditional hot air dryer. {yields} Feasibility of the HPD is also validated by the operation economy estimation. - Abstract: A heat pump dryer (HPD) would be an economic, environmentally friendly, hygienic drying machine used to dry some food, such as hawthorn cakes. Based on the production process of the hawthorn cake, a HPD is proposed and its basic principle is introduced. The experimental drying curves of the hawthorn cake using the heat pump drying method and the traditional hot air drying method are compared and analyzed. The drying process of hawthorn cakes is similar to that of the other drying materials. The higher drying temperature causes a faster drying process. But in the initial stage of the heat pump drying process, the water content of the hawthorn cake is not sensitive to the drying temperature, so a lower drying air temperature can be available in order to get a higher coefficient of performance (COP) of the heat pump (HP). The experimental results and the economic analysis indicate that the HPD is feasibly used to dry hawthorn cakes.

Participation of Danish and immigrant cleaners in a 1-year worksite intervention preventingphysical deterioration

DEFF Research Database (Denmark)

Rasmussen, Charlotte D N; Jørgensen, Marie B; Carneiro, Isabella G

2012-01-01

differences in participation among immigrant and Danish cleaners throughout a 1-year randomised controlled study tailored to cleaners and carried out in predominantly female workplaces. No significant differences in ethnicity were found in consent and participation throughout the 1-year intervention. Dropout...... was equally distributed among Danish and immigrant cleaners. This study indicates that a worksite health promotion intervention among a female-dominated, high-risk occupation such as cleaning can be equally appealing for Danes and immigrants. Statement of Relevance: This study provides insight about...... participation of Danish and immigrant cleaners in a worksite health promotion intervention in a predominantly female occupation. For attaining high participation and low dropout in future worksite health promotion interventions among cleaners, the intervention ought to not only target the ethnic background...

Design, manufacture and modeling of a mixed mode dryer for pistachio in Kerman

Energy Technology Data Exchange (ETDEWEB)

Ameri, Mehran; Zangiabadi, Bijan; Mahmoudabadi, Mehdi [Department of Mechanical Engineering, Shahid Bahonar University, Kerman (Iran, Islamic Republic of)

2006-01-15

Production of high quality nuts that have toxics less than 2-2.5 ppm requires a great attention during growing and post harvest processing. Gravitational or Wagon driver using fossil fuel has been traditionally performed to dry pistachio nuts. However, using of fossil fuel is subject to the noxious effects on nuts such as burning, discoloured and various toxic fumes as well as the biological pollution. In Kerman province in south of Iran, where 60% of pistachio nuts export to all over the world, due to long period of sunshine during harvesting season, solar drying are know to be an excellence alternative to the fossil fuel. A specimen mixed-mode solar-dryer is manufactured to study the feasibility of test and to investigate optimization of the drying process in several conditions. Furthermore this designed dryer for pistachio nuts can be simply used for drying of the various agriculture products like fruits and vegetables. With this proposed multi application solar dryer, one can easily reach to acceptable moisture (7%) in a short period of time. For this system a mathematical model of dryer is also suggested here. the proposed solar dryer includes three main parts as collector, chamber and photocell. Chamber has a glassy cover that permits nut expose beam radiation directly. Collector has ability to circulate air by buoyancy forces or convey air by suction fans due to different operation conditions. Photocells prepare electromotive force for fans.National capacity of the dryer is 50Kg. The maximum temperature inside collector at the end of harvest season is 60 degree centigrade during 8-16 local time. In the mathematical modeling after fitting the drawing curves with the remaining moisture amount in the nuts and temperature per drying time, it was found that the major drop in the moisture content of the nuts occurs during the first 9 hours and then decreases gradually. The final moisture amount of the nuts was about 6% in 42 hours. The accuracy of proposed method

Design, manufacture and modeling of a mixed mode dryer for pistachio in Kerman

International Nuclear Information System (INIS)

Ameri, Mehran; Zangiabadi, Bijan; Mahmoudabadi, Mehdi

2006-01-01

Production of high quality nuts that have toxics less than 2-2.5 ppm requires a great attention during growing and post harvest processing. Gravitational or Wagon driver using fossil fuel has been traditionally performed to dry pistachio nuts. However, using of fossil fuel is subject to the noxious effects on nuts such as burning, discoloured and various toxic fumes as well as the biological pollution. In Kerman province in south of Iran, where 60% of pistachio nuts export to all over the world, due to long period of sunshine during harvesting season, solar drying are know to be an excellence alternative to the fossil fuel. A specimen mixed-mode solar-dryer is manufactured to study the feasibility of test and to investigate optimization of the drying process in several conditions. Furthermore this designed dryer for pistachio nuts can be simply used for drying of the various agriculture products like fruits and vegetables. With this proposed multi application solar dryer, one can easily reach to acceptable moisture (7%) in a short period of time. For this system a mathematical model of dryer is also suggested here. the proposed solar dryer includes three main parts as collector, chamber and photocell. Chamber has a glassy cover that permits nut expose beam radiation directly. Collector has ability to circulate air by buoyancy forces or convey air by suction fans due to different operation conditions. Photocells prepare electromotive force for fans.National capacity of the dryer is 50Kg. The maximum temperature inside collector at the end of harvest season is 60 degree centigrade during 8-16 local time. In the mathematical modeling after fitting the drawing curves with the remaining moisture amount in the nuts and temperature per drying time, it was found that the major drop in the moisture content of the nuts occurs during the first 9 hours and then decreases gradually. The final moisture amount of the nuts was about 6% in 42 hours. The accuracy of proposed method

A study of the drying effect on lemon slices using a closed-type solar dryer

Energy Technology Data Exchange (ETDEWEB)

Ho-Hsien Chen; Hernandez, C.E.; Tzou-Chi Huang [National Pingtung University of Science and Technology (China). Dept. of Food Science

2005-01-01

An experimental closed-type dryer associated with a photovoltaic system (PV) was developed. The transparent drying cabinet was designed with high transmittance glass to decrease the reflection of direct sunlight and to offer extra direct solar heating on the raw material during drying. Parallel wiring with a local electrical grid was necessary for switching purposes if there is insufficient battery backup during peak operation. Lemon slices were dried using the closed-type solar dryer and results were compared with hot air drying at 60{sup o}C. The results indicate that the dried lemon slices using a closed-type solar dryer has better general levels of quality in terms of sensory parameters. (author)

Evaluation of several air cleaners for reducing indoor radon progeny

International Nuclear Information System (INIS)

Hopke, P.K.; Jensen, B.; Montassier, N.

1994-01-01

Over the past several years, studies have been made of the effectiveness of several kinds of air cleaners in removing radon decay products from indoor air using a recently developed automated, semi-continuous measurement system that can determine the activity-weighted size distributions in occupied homes. Measurements of activity-weighted size distributions and radon concentrations were made every 90 min in a home with a high air exchange rate. A week-long series of measurements was made for the home with no cleaner operating and a similar set of measurements were made for each of the air cleaners. Two different types of air cleaners were tested in this study; filtration units (two different designs from two different manufacturers) and two ion generator/fan systems (identical design NO-RAD systems, but from two different manufacturers). It was found that the filtration units resulted in a median reduction in exposure of 15% and 36% for the two units and corresponding dose reductions of 32% and 53%. The two NO-RAD systems produced 37% and 10% reductions in the median exposure, but the reductions in the median dose were 49% and 46%. (author)

Performance Evaluation of a Pebble Bed Solar Crop Dryer ...

African Journals Online (AJOL)

Nigerian Journal of Technology ... The solar crop dryer consists of an imbedded pebble bed solar heat storage unit/solar collector ... The crop-drying chamber is made of drying trays of wire gauze while the roof is made of transparent glazing.

Design and Fabrication of a Direct Natural Convection Solar Dryer for Tapioca

Directory of Open Access Journals (Sweden)

Diemuodeke E. OGHENERUONA

2011-06-01

Full Text Available Based on preliminary investigations under controlled conditions of drying experiments, a direct natural convection solar dryer was designed and fabricated to dry tapioca in the rural area. This paper describes the design considerations followed and presents the results of MS excel computed results of the design parameters. A minimum of 7.56 m2 solar collector area is required to dry a batch of 100 kg tapioca in 20 hours (two days drying period. The initial and final moisture content considered were 79 % and 10 % wet basis, respectively. The average ambient conditions are 32ºC air temperatures and 74 % relative humidity with daily global solar radiation incident on horizontal surface of 13 MJ/m2/day. The weather conditions considered are of Warri (lat. 5°30’, long. 5°41’, Nigeria. A prototype of the dryer so designed was fabricated with minimum collector area of 1.08 m2. This prototype dryer will be used in experimental drying tests under various loading conditions.

Technical and environmental analysis of biofuel dryers; Teknisk och miljoemaessig analys av biobraensletorkar

Energy Technology Data Exchange (ETDEWEB)

Muenter, M; Hagman, U; Harnevie, H; Johansen, H; Kristensson, I; Westermark, M; Viberg, T [Vattenfall Energimarknad, Stockholm (Sweden)

1999-03-01

A study regarding technology and environmental impact of the drying process of biofuels has been conducted. In the study two different types of dryers are analyzed. The result from the study shows that emissions of primarily hydrocarbons is high from the direct technic. The emission can be decreased considerably by improving the burner of the dryer. For the indirect technic the evaporated water give rise to problems in the sewage treatment plant. Studies show that biological treatment will result in an acceptable condensate.

Environmental Technology Verification: Supplement to Test/QA Plan for Biological and Aerosol Testing of General Ventilation Air Cleaners; Bioaerosol Inactivation Efficiency by HVAC In-Duct Ultraviolet Light Air Cleaners

Science.gov (United States)

The Air Pollution Control Technology Verification Center has selected general ventilation air cleaners as a technology area. The Generic Verification Protocol for Biological and Aerosol Testing of General Ventilation Air Cleaners is on the Environmental Technology Verification we...

Does aerobic exercise improve or impair cardiorespiratory fitness and health among cleaners?

DEFF Research Database (Denmark)

Korshøj Larsen, Mette; Lidegaard, Mark; Skotte, Jørgen H

2015-01-01

OBJECTIVE: It is unknown if aerobic exercise overloads or improves the cardiovascular system among workers with high occupational physical activity. This was investigated in a worksite randomized controlled trial (RCT) of aerobic exercise among cleaners. METHODS: We randomized 116 cleaners betwee...

76 FR 71342 - Proposed CERCLA Administrative Cost Recovery Settlement; River Forest Dry Cleaners Site, River...

Science.gov (United States)

2011-11-17

... Settlement; River Forest Dry Cleaners Site, River Forest, Cook County, IL AGENCY: Environmental Protection... response costs concerning the River Forest Dry Cleaners site in River Forest, Cook County, Illinois with... code: C-14J, Chicago, Illinois 60604. Comments should reference the River Forest Dry Cleaners Site...

Mushroom dehydration in a hybrid-solar dryer

International Nuclear Information System (INIS)

Reyes, Alejandro; Mahn, Andrea; Cubillos, Francisco; Huenulaf, Pedro

2013-01-01

Highlights: ► Mushrooms (Paris variety) were dehydrated in a hybrid solar dryer. ► Effective diffusivity was estimated by the Constant Diffusivity Model. ► Drying kinetics were adjusted by a semi-theoretical and the empirical Page model. ► Temperature, thickness and air recycle significantly affected critical moisture. ► The input of solar energy resulted in 3.5–12.5% electrical energy saving. - Abstract: Mushrooms (Paris variety) were dehydrated in a hybrid solar dryer (HSD) provided with a 3 m 2 solar panel and electric resistances. Mushrooms were cut in 8 mm or 4 mm thickness slices. At the outlet of the tray dryer 80–90% air was recycled and the air temperature was adjusted to the pre-defined levels (50 or 60 °C). At the outlet of the solar panel the air temperature raised between 2 and 20 °C above the ambient temperature, depending mainly of solar radiation level. Temperature, slices thickness and air recycle level had statistically significant effects on critical moisture content (X c ), as well as on the time necessary to reach a moisture content of 0.1 (wb). The color parameters of dehydrated mushroom indicate a notorious darkening, in all runs. Rehydration assays at 35 °C showed that in less than 30 min rehydrated mushrooms reached a moisture content of 0.8 (wb). Effective diffusivity (D eff ) was estimated by the Simplified Constant Diffusivity Model (SCDM), and it ranged between 6E−10 and 40E−10 m 2 /s, with R 2 higher than 0.98, agreeing with literature. The adjustment of experimental drying kinetics with the empirical Page’s model resulted in R 2 higher than 0.997. Finally, the input of solar energy resulted in 3.5–12.5% energy saving. These values could even be improved by increasing the agro-product load in the HSD

A Study on Promotion and Implementation of Cleaner Production Practices in Malaysian Industry - Development of a National Program and Action Plan for Promotion of Cleaner Production. Progress Report 1

DEFF Research Database (Denmark)

Wangel, Arne

This Progress Report presents the initial findings of the research project 'A Study on Promotion and Implementation of Cleaner Production Practices in Malaysian Industry - Development of a National Program and Action Plan for Promotion of Cleaner Production. Progress Report' funded...

Improving Dryer and Press Efficiencies Through Combustion of Hydrocarbon Emissions

Energy Technology Data Exchange (ETDEWEB)

Sujit Banerjee

2005-10-31

Emission control devices on dryers and presses have been legislated into the industry, and are now an integral part of the drying system. These devices consume large quantities of natural gas and electricity and down-sizing or eliminating them will provide major energy savings. The principal strategy taken here focuses on developing process changes that should minimize (and in some cases eliminate) the need for controls. A second approach is to develop lower-cost control options. It has been shown in laboratory and full-scale work that Hazardous Air Pollutants (HAPs) emerge mainly at the end of the press cycle for particleboard, and, by extension, to other prod-ucts. Hence, only the air associated with this point of the cycle need be captured and treated. A model for estimating terpene emissions in the various zones of veneer dryers has been developed. This should allow the emissions to be concentrated in some zones and minimized in others, so that some of the air could be directly released without controls. Low-cost catalysts have been developed for controlling HAPs from dryers and presses. Catalysts conventionally used for regenerative catalytic oxidizers can be used at much lower temperatures for treating press emissions. Fluidized wood ash is an especially inexpensive mate-rial for efficiently reducing formaldehyde in dryer emissions. A heat transfer model for estimating pinene emissions from hot-pressing strand for the manufacture of flakeboard has been constructed from first principles and validated. The model shows that most of the emissions originate from the 1-mm layer of wood adjoining the platen surface. Hence, a simple control option is to surface a softwood mat with a layer of hardwood prior to pressing. Fines release a disproportionate large quantity of HAPs, and it has been shown both theo-retically and in full-scale work that particles smaller than 400 µm are principally responsible. Georgia-Pacific is considering green

Short-term respiratory effects of cleaning exposures in female domestic cleaners.

Science.gov (United States)

Medina-Ramón, M; Zock, J P; Kogevinas, M; Sunyer, J; Basagaña, X; Schwartz, J; Burge, P S; Moore, V; Antó, J M

2006-06-01

Symptoms of obstructive lung disease in domestic cleaners have been related to the use of bleach and other irritant cleaning products. The short-term effects of cleaning exposures on respiratory symptoms and peak expiratory flow (PEF) were investigated in domestic cleaners with respiratory disorders. In a panel study, 43 female domestic cleaners with a recent history of asthma and/or chronic bronchitis completed a 2-week diary, collecting information on respiratory symptoms, PEF and cleaning exposures. Mixed regression models were used to assess daily changes in symptoms and PEF associated with specific cleaning exposures. The probability of having work-related asthma was individually assessed by a computerised diagnostic system and an occupational asthma expert. Lower respiratory tract symptoms were more common on working days and were predominantly associated with exposure to diluted bleach, degreasing sprays/atomisers and air fresheners. Associations with upper respiratory tract symptoms and PEF were less apparent. Eleven (30%) subjects scored positively for work-related asthma. It is concluded that exposure to certain irritant cleaning products aggravates lower respiratory tract symptoms in female domestic cleaners with asthma or chronic bronchitis.

Design, construction and test run of a two-tonne capacity solar rice dryer with rice-husk-fired auxiliary heater

International Nuclear Information System (INIS)

Iloeje, O.C.; Ekechukwu, O.V.; Ezeike, G.O.I.

1993-09-01

The design and construction details of a two-tonne per batch capacity natural-circulation solar rice dryer and the highlights of the design of its rice-husk-fired auxiliary heating system which is still under construction are presented. The dryer measures approximately 17.7m long by 9.8m wide by 6m high. Preliminary results of a test run on the solar dryer section only is reported. (author). 5 refs, 3 figs

Development of a multi-purpose dryer | Kadurumba | Nigeria ...

African Journals Online (AJOL)

The novel design uses heat sources from electric burners and it is located beneath the product spreading chamber. This prevented the problem of discoloration due to direct heat from the burners. A thermostat was used for its temperature control and light indicators were introduced to monitor the operation of the dryer with a ...

The Life, Work and Recreational Physical Activity of Female Cleaners

DEFF Research Database (Denmark)

Lenneis, Verena

The main aim of this article-based PhD thesis was to explore the recreational physical activity participation of female cleaners – an occupational group mainly consisting of minority ethnic women from non-western countries. As the PhD project was integrated in and financially supported...... by the Copenhagen Centre for Team Sport and Health, a part of the PhD project was to organize and evaluate a workplace physical activity programme that used team games as the main form of exercise. Via participant observation and semi-structured interviews with 42 cleaners and their supervisors I gained insights...... and employed different theories, they drew a coherent picture: the interviewees’ everyday lives as migrant cleaners in Denmark had a decisive influence on their opportunities to engage in recreational physical activity: most women struggled with the demands of a physically exhausting job and an extensive...

A study on the sound quality evaluation model of mechanical air-cleaners

DEFF Research Database (Denmark)

Ih, Jeong-Guon; Jang, Su-Won; Jeong, Cheol-Ho

2009-01-01

In operating the air-cleaner for a long time, people in a quiet enclosed space expect low sound at low operational levels for a routine cleaning of air. However, in the condition of high operational levels of the cleaner, a powerful yet nonannoying sound is desired, which is connected to a feeling...... of an immediate cleaning of pollutants. In this context, it is important to evaluate and design the air-cleaner noise to satisfy such contradictory expectations from the customers. In this study, a model for evaluating the sound quality of air-cleaners of mechanical type was developed based on objective...... and subjective analyses. Sound signals from various aircleaners were recorded and they were edited by increasing or decreasing the loudness at three wide specific-loudness bands: 20-400 Hz (0-3.8 barks), 400-1250 Hz (3.8-10 barks), and 1.25- 12.5 kHz bands (10-22.8 barks). Subjective tests using the edited...

Corn Drying with Zeolite in The Fluidized Bed Dryer under Medium Temperature

Directory of Open Access Journals (Sweden)

Mohamad Djaeni

2013-08-01

Full Text Available Drying is an important step to find high quality of corn. Based on Standard of National Industry, populer as SNI, number 01-3920-1995, the corn was well stored at moisture content 14% or below (wet basis. However, conventional corn drying dealed with in-efficient energy process and corn quality degradation. This research evaluated the performance of corn drying assisted by zeolite as moisture adsorbent. In this process, the zeolite and corn were placed in the dryer fluidized by warm air as drying medium under 40 - 50oC. The air evaporated water product from corn, and at same time the zeolite adsorbed moisture in air. So, the relative humidity of air in dryer can be kept low in which enhanced the driving force for drying. Beside that, the moisture adsoprtion by zeolite was exothermic process that can supply the energy for drying or keep the dryer temperature. Thus, the drying rate can be faster. This work foccussed to observe the effect of drying temperature, air velocity, and corn to zeolite ratio on drying time as well as corn quality. As indicators, the drying rate was estimated and the proxymates content such as protein, fat, and carbohydrate content were analyzed. The results showed that compared with conventional fluidised bed dryer, corn drying with zeolite, can speed up drying time as well as improving the constant of drying rate. In addition, the corn proximate nutrition content can be well retained. At operating temperature 40oC, air velocity 9 m.s-1, and zeolite to corn ratio 1:2, the drying time can be 60 minutes shorter compared to that without zeolite.

A large-scale solar greenhouse dryer using polycarbonate cover: Modeling and testing in a tropical environment of Lao People's Democratic Republic

Energy Technology Data Exchange (ETDEWEB)

Janjai, Serm; Intawee, Poolsak; Kaewkiew, Jinda; Sritus, Chanoke [Solar Energy Research Laboratory, Department of Physics, Faculty of Science, Silpakorn University, Nakhon Pathom 73000 (Thailand); Khamvongsa, Vathsana [Department of Physics, Faculty of Natural Science, National University of Laos, P O Box 7322, Vientiane (Lao People' s Democratic Republic)

2011-03-15

A large-scale solar greenhouse dryer with a loading capacity of 1000 kg of fruits or vegetables has been developed and tested at field levels. The dryer has a parabolic shape and the dryer is covered with polycarbonate sheets. The base of the dryer is a black concrete floor with an area of 7.5 x 20.0 m{sup 2}. Nine DC fans powered by three 50-W solar cell modules are used to ventilate the dryer. The dryer was installed at Champasak (15.13 N, 105.79 E) in Lao People's Democratic Republic (Lao PDR). It is routinely used to dry chilli, banana and coffee. To assess the experimental performances of the dryer, air temperature, air relative humidity and product moisture contents were measured. One thousand kilograms of banana with the initial moisture content of 68% (wb) was dried within 5 days, compared to 7 days required for natural sun drying with the same weather conditions. Also three hundred kilograms of chilli with the initial moisture content of 75% (wb) was dried within 3 days while the natural sun drying needed 5 days. Two hundred kilograms of coffee with the initial moisture content of 52% (wb) was dried within 2 days as compared to 4 days required for natural sun drying. The chilli, coffee and banana dried in this dryer were completely protected from insects, animals and rain. Furthermore, good quality of dried products was obtained. The payback period of the dryer is estimated to be 2.5 years. A system of partial differential equations describing heat and moisture transfer during drying of chilli, coffee and banana in the greenhouse dryer was developed. These equations were solved by using the finite different method. The simulated results agree well with the experimental data. This model can be used to provide the design data for this type of dryer in other locations. (author)

Cleaner production - a tool for sustainable environmental development

International Nuclear Information System (INIS)

Ahmad, I.; Batool, S.

2005-01-01

Industrial Development and Production with no regard for environmental impacts creates water and air pollution, soil degradation, and large-scale global impacts such as acid rain, global warming and ozone depletion. To create more sustainable methods of industrial production, there needs to be a shift in attitudes away from control towards pollution prevention and management. Cleaner Production (CP) refers to a management process that seeks out and eliminates the causes of pollution, waste generation and resource consumption at their source through input reductions or substitutions, pollution prevention, internal recycling and more efficient production technology and processes for sustainable environmental development. The objective of cleaner production is to avoid generating pollution in the first place, which frequently cuts costs, reduces risks associated with liability, and identifies new market opportunities. Introducing cleaner production has become a goal to improve the competitiveness through increased eco-efficiency. CP is a business strategy for enhancing productivity and environmental performance for overall socio-economic development. The environmental and economic benefits can only be achieved by implementing cleaner production tools. The CP assessment methodology is used to systematically identify and evaluate the waste minimization opportunities and facilitate their implementation in industries. It refers to how goods and services are produced with the minimum environmental impact under present technological and economic limits. CP shares characteristics with many environmental management tools such as Environmental Assessment or Design for Environment by including them among the technological options for reducing material and energy intensiveness in production, as well as facilitating ruse trough remanufacturing and recycling. It is thus an extension of the total quality management process. The CP program has been successfully implemented in

Thermal decomposition study of uranyl nitrate and cerium hydroxide in a spray dryer

International Nuclear Information System (INIS)

Silva Wildhagen, G.R. da.

1993-05-01

A study, in a spray dryer system based on drying and thermal decomposition of uranyl nitrate solutions aiming the production of uranium trioxide adequate for the use in posterior steps of reduction and hydro fluorination in nuclear fuel cycle; and cerium hydroxide suspensions for the production of cerium oxide with high surface area is presented. Thus, the project and construction of a countercurrent spray dryer was elaborated for capacity of 10 Kg U O 3 /h and 3,5 k Ce O 2 /h. The methodology used in these experiments consisted in the analysis of several parameters (concentration and flow rate of the feed, atomization pressure and inlet temperature of the dryer) over the physical and chemical properties of the products. Using the obtained results, with the help of a mathematical model, it was developed the project of a continuous pilot unity for the production of uranium trioxide or cerium oxide, with capacity of 20 Kg U O 3 /h or 10 Kg Ce O 2 /h, respectively. (author)

A solar assisted heat-pump dryer and water heater

International Nuclear Information System (INIS)

Hawlader, M.N.A.; Chou, S.K.; Jahangeer, K.A.; Rahman, S.M.A.

2006-01-01

Growing concern about the depletion of conventional energy resources has provided impetus for considerable research and development in the area of alternative energy sources. A solar assisted heat pump dryer and water heater found to be one of the solutions while exploring for alternative energy sources. The heat pump system is used for drying and water heating applications with the major share of the energy derived from the sun and the ambient. The solar assisted heat pump dryer and water heater has been designed, fabricated and tested. The performance of the system has been investigated under the meteorological conditions of Singapore. The system consists of a variable speed reciprocating compressor, evaporator-collector, storage tank, air cooled condenser, auxiliary heater, blower, dryer, dehumidifier, and air collector. The drying medium used is air and the drying chamber is configured to carry out batch drying of good grains. A water tank connected in series with the air cooled condenser delivers hot water for domestic applications. The water tank also ensures complete condensation of the refrigerant vapour. A simulation program is developed using Fortran language to evaluate the performance of the system and the influence of different variables. The performance indices considered to evaluate the performance of the system are: Solar Fraction (SF), Coefficient of Performance (COP) and Specific Moisture Extraction Rate (SMER). A COP value of 7.5 for a compressor speed of 1800 rpm was observed. Maximum collector efficiencies of 0.86 and 0.81 have been found for evaporator-collector and air collector, respectively. A value of the SMER of 0.79 has been obtained for a load of 20 kg and a compressor speed of 1200 rpm

GUIDE TO CLEANER TECHNOLOGIES: ORGANIC COATING REMOVAL

Science.gov (United States)

A cleaner technology is a source reduction or recycle method |applied to eliminate or significantly reduce hazardous waste generation. Source reduction includes product changes and source control. Source control can be further characterized as input material changes, technology...

Measurement of concentration and size distribution of radon decay products in homes using air cleaners

International Nuclear Information System (INIS)

Montassier, N.; Hopke, P.K.; Shi, Y.; McCallum, B.

1992-01-01

By removing particles, air cleaners can also eliminate radon decay products. However, by removing the particles, the open-quotes unattachedclose quotes fraction of the radon progeny is increased leading to a higher dose per unit exposure. Thus, both the concentration and size distributions of the radon decay products are needed to evaluate air cleaners. Three types of room air cleaners, NO-RAD Radon Removal System, Electronic Air Cleaner and PUREFLOW Air Treatment System were tested in a single family home in Arnprior, Ontario (Canada). Semi-continuous measurements of radon gas concentration and radon decay product activity weighted size distribution were performed in the kitchen/dining room under real living conditions. The effects of air cleaners on both the concentration and size distribution of the radon decay products were measured, and their impact on the dose of radiation given to the lung tissue were examined

Development of Simple Drying Model for Performance Prediction of Solar Dryer: Theoretical Analysis

DEFF Research Database (Denmark)

Singh, Shobhana; Kumar, Subodh

2012-01-01

An analytical moisture diffusion model which considers the influence of external resistance to mass transfer is developed to predict thermal performance of dryer system. The moisture diffusion coefficient, Deff that is necessary to evaluate the prediction model has been determined in terms...... of experimental drying parameters. A laboratory model of mixed-mode solar dryer system is tested with cylindrical potato samples of thickness 5 and 18 mm under simulated indoor conditions. The potato samples were dried at a constant absorbed thermal energy of 750 W/m2 and air mass flow rate of 0.011 kg...

Employee participation and cleaner technology: learning processes in environmental teams

DEFF Research Database (Denmark)

Remmen, Arne; Lorentzen, Børge

2000-01-01

The approach to pollution prevention in Danish industries in the late-1980s and in the beginning of the 1990s met criticism, because the cleaner technology projects focused too narrowly on technical solutions implemented by experts. The objective of the project “Employee Participation in the Impl...... to improve the firms' environmental activities (e.g. setting up environmental policies, targets and action plans, implementing new procedures and technologies).......The approach to pollution prevention in Danish industries in the late-1980s and in the beginning of the 1990s met criticism, because the cleaner technology projects focused too narrowly on technical solutions implemented by experts. The objective of the project “Employee Participation...... in the Implementation of Cleaner Technology” was to develop a more active role for employees in the environmental activities of companies. Based on practical experiments in five Danish firms within different industrial sectors, the project concluded that employee participation can have a strong effect on changing...

40 CFR 761.378 - Decontamination, reuse, and disposal of solvents, cleaners, and equipment.

Science.gov (United States)

2010-07-01

... of solvents, cleaners, and equipment. 761.378 Section 761.378 Protection of Environment ENVIRONMENTAL...-Porous Surfaces § 761.378 Decontamination, reuse, and disposal of solvents, cleaners, and equipment. (a) Decontamination. Decontaminate solvents and non-porous surfaces on equipment in accordance with the standards and...

GUIDE TO CLEANER TECHNOLOGIES: ORGANIC COATING REPLACEMENTS

Science.gov (United States)

This guide describes available and emerging cleaner technologies that can be used to reduce emissions and wastes from paint and coatings applications. Environmental concerns and increasing costs of organic chemicals and metals are leading to changes in the formulation of organic ...

Education and Manpower development for Cleaner Production

DEFF Research Database (Denmark)

Jørgensen, Michael Søgaard

1996-01-01

An overview of the needs for education and training for dissemination and implementation of cleaner production. Expericne from training in companies and training of officials from public authorities and from integration into engineering, business and management and social science curricula...

Cleaner Production Practices, Environmental Management and National Policy Development in Malaysia for Electroplating Enterprises

DEFF Research Database (Denmark)

Wangel, Arne; Mohamed, Maketab; Agamuthu, P.

2004-01-01

-operation for Environment and Development (DANCED), Ministry of Environment and Energy. SMEs were targeted within three sectors: Textile, food and electroplating industries. The paper illustrates the change process from the perspective of electroplating SMEs by reviewing the cleaner production options chosen, presenting...... figures on the results achieved, and discussing the experiences gained. Reviewing the approach and results of the Centre, as well as the status of cleaner production (CP) in Malaysia, the paper outlines the challenges for national policy making, when moving from promotion by project intervention towards...... sustainable practices in the SME sector at large. The paper draws upon data collection conducted by the research project 'A Study on Promotion and Implementation of Cleaner Production Practices in Malaysian Industry - Development of a National Program and Action Plan for Promotion of Cleaner Production'....

Performance analysis of greenhouse dryer by using insulated north-wall under natural convection mode

Directory of Open Access Journals (Sweden)

Prashant Singh Chauhan

2016-11-01

Full Text Available A prototype north wall insulated greenhouse dryer has been fabricated and tested in no-load conditions under natural convection mode. Experimentation has been conducted in two different cases. Case-I is when solar collector placed inside the dryer and Case-II is North wall insulated greenhouse dryer without solar collector. Coefficient of performance, heat utilisation factor, convective heat transfer coefficient and coefficient of diffusivity have been evaluated in thermal performance analysis. The difference of the highest convective heat transfer coefficient of both cases is 29.094W/m2°C which is showing the effectiveness of insulated north wall and solar collector. The maximum coefficient of diffusivity (0.0827 was achieved during the third day of experiment in Case-II. The inside room temperature of wall insulated greenhouse dryer for Case-I is 4.11%, 5.08 % and 11.61 % higher than the Case-II during the day 1, day 2 and day 3 respectively. This result is also showing the effectiveness of solar collector and insulated north wall. The highest heat utilisation factor (0.616 is obtained during the second day for Case-I while for Case-II it is 0.769 during the third day of experimentation. Maximum coefficient of performance achieved is 0.892 during the third day of the experiment for Case-I whereas 0.953 is obtained on the first day of experimentation for Case-II.

Visibility and social recognition as psychosocial work environment factors among cleaners in a multi-ethnic workplace intervention.

Science.gov (United States)

Hviid, Kirsten; Smith, Louise Hardman; Frydendall, Karen Bo; Flyvholm, Mari-Ann

2012-12-24

This article focuses on the psychosocial work environment of immigrant cleaners at a Danish workplace. Today, many cleaners working in Danish cleaning jobs are women from the established immigrant communities, but also labour migrants from the newer EU member states have found their way to the cleaning industry. Studies have drawn attention to immigrants' low position in the cleaning industry and their increased risk of work injuries. This article is based on a case study of an intervention called "Make a Difference" designed to improve the work environment among cleaners at a multi-ethnic workplace. We used semi-structured interviews, photo logs, observation and participation to investigate how the cleaners experienced their work environment. The cleaners reported an overload of heavy work, related to the concept of a classroom's "readiness for cleaning", and they expressed strained social relations and communication in addition to a lack of social recognition and invisibility at the workplace, a school. We analysed these psychosocial work environmental problems by investigating the different forms of social relationships and communication within the group of cleaners, and between the cleaners and the teachers and pupils at the school. Moreover, we discussed why the intervention, based on training of language and cleaning skills and social interaction, only partially improved the cleaners' psychosocial work environment problems. In this article, we argue that social divisions based on ethnicity between the new and the established group of cleaners, combined with their marginal position and poor work organisation at the school, reinforced the cleaners' experiences of psychosocial work environment problems. This article suggests that increased effort towards social inclusion at work and improved work organisation, especially for the new labour migrants from newer EU-countries, should be considered.

Aerobic exercise reduces biomarkers related to cardiovascular risk among cleaners

DEFF Research Database (Denmark)

Korshøj, Mette; Ravn, Marie Højbjerg; Holtermann, Andreas

2016-01-01

PURPOSE: Blue-collar workers have an increased risk of cardiovascular disease. Accordingly, elevated levels of biomarkers related to risk of cardiovascular disease, such as high-sensitive C-reactive protein, have been observed among blue-collar workers. The objective was to examine whether...... an aerobic exercise worksite intervention changes the level of inflammation biomarkers among cleaners. METHODS: The design was a cluster-randomized controlled trial with 4-month worksite intervention. Before the 116 cleaners aged 18-65 years were randomized, they signed an informed consent form...

A 24-h assessment of physical activity and cardio-respiratory fitness among female hospital cleaners

DEFF Research Database (Denmark)

Larsen, Mette Korshøj; Krustrup, Peter; Jespersen, Tobias

2013-01-01

measured. The methods were feasible for the objective 24-h sampling of physical activity and cardio-respiratory fitness among cleaners. Measurements showed that the cleaners walked 20,198 ± 4,627 steps per day. During working hours, the average cardio-respiratory load was 25 ± 6% of heart rate reserve (HRR......). The cleaners had a low estimated cardio-respiratory fitness (34 mlO2/kg/min), a high BMI (50%, >25 kg/m(2)) and blood pressure (50%, >120/>80 mmHg). The high amount of steps, the relatively high cardiovascular load at work and low cardio-respiratory fitness illustrate the need for further investigation...... of the relationship between physical activity at work and in leisure, and cardiovascular health in this population. Practitioner Summary: This study evaluated the feasibility of methods for objective 24-h sampling of physical activity among cleaners; the methods used were found to be feasible. The cleaners had a high...

Drying of Rosella (Hibiscus sabdariffa) Flower Petals using Solar Dryer with Double Glass Cover Collector

OpenAIRE

Tjukup Marnoto

2014-01-01

Chemical ingredients in rosella petals are very beneficial for health. Rosella petals needed to be drained for storage and packing purpose. The traditional drying takes 5 days and less healthy. Solar dryer technology can speed up the drying process and protect materials from dust contamination. Solar dryer with double glass covered collector has been designed and made for drying of agricultural products such as rosella flowers. Rosella petals as much as 2300 grams with initial moisture conten...

Steam generator with integral downdraft dryer. Final project report

Energy Technology Data Exchange (ETDEWEB)

Hochmuth, F.W.

1992-02-01

On June 30, 1989, a financial assistance award was granted by the United State Department of Energy, the purpose of which was to study and evaluate the technical aspect, the economic viability, and commercial possibilities of a new furnace design for burning high moisture cellulose type fuels. The new design is an invention by F.W. Hochmuth, P.Eng. and has received United States Patents Nos. 4,480, 557 and 4,502,397. It was conceived as a method to improve the general operation and efficiency of waste wood burning boilers, to avoid the use of stabilizing fuels such as oil or gas, and to reduce objectionable stack emissions. A further objective was to obtain such benefits at relatively low cost by integrating all new material requirements within the furnace itself thereby avoiding the need for costly external equipment. The proposed integral down-draft dryer avoids the use of external dryer systems that are very expensive, have high power consumption, and require a large amount of maintenance. This document provides the details of this invention.

Performance of a convective, infrared and combined infrared- convective heated conveyor-belt dryer.

Science.gov (United States)

El-Mesery, Hany S; Mwithiga, Gikuru

2015-05-01

A conveyor-belt dryer was developed using a combined infrared and hot air heating system that can be used in the drying of fruits and vegetables. The drying system having two chambers was fitted with infrared radiation heaters and through-flow hot air was provided from a convective heating system. The system was designed to operate under either infrared radiation and cold air (IR-CA) settings of 2000 W/m(2) with forced ambient air at 30 °C and air flow of 0.6 m/s or combined infrared and hot air convection (IR-HA) dryer setting with infrared intensity set at 2000 W/m(2) and hot at 60 °C being blown through the dryer at a velocity of 0.6 m/s or hot air convection (HA) at an air temperature of 60 °C and air flow velocity 0.6 m/s but without infrared heating. Apple slices dried under the different dryer settings were evaluated for quality and energy requirements. It was found that drying of apple (Golden Delicious) slices took place in the falling rate drying period and no constant rate period of drying was observed under any of the test conditions. The IR-HA setting was 57.5 and 39.1 % faster than IR-CA and HA setting, respectively. Specific energy consumption was lower and thermal efficiency was higher for the IR-HA setting when compared to both IR-CA and HA settings. The rehydration ratio, shrinkage and colour properties of apples dried under IR-HA conditions were better than for either IR-CA or HA.

A model for the thermodynamic analysis in a batch type fluidized bed dryer

International Nuclear Information System (INIS)

Özahi, Emrah; Demir, Hacımurat

2013-01-01

An original model for thermodynamic analysis of a batch type fluidized bed dryer is proposed herein considering two separate systems comprised of drying air medium as a control volume and particles to be dried as a control mass. By means of the proposed model, energetic and exergetic analyses of a drying column of a batch type fluidized bed dryer are carried out as an original contribution to literature since there is no such like model in which the analyses are performed considering two separate systems. The energetic efficiencies evaluated by means of the proposed model using the data in literature are compared with those in literature and a good conformity is satisfied with an acceptable error margin of ±9%. A new correlation is also developed with a mean deviation of ±10% in order to evaluate the energetic efficiency for not only corn drying process but also drying processes of other particles at inlet air temperature of 50 °C. Effects of air mass flow rate, mass of particle and ambient temperature on energetic and exergetic efficiencies are analyzed and some concluding remarks are highlighted for further studies. - Highlights: • Energetic and exergetic analyses of a batch type fluidized bed dryer are developed. • An original model is proposed for thermodynamic analyses in a fluidized bed dryer. • The proposed model is compared with the data in literature with an accuracy of ±9%. • Effect of air mass flow rate is more significant than that of ambient temperature. • Effect of mass of particle is more significant than that of ambient temperature

Research of selection seeds drying in dense layer

Directory of Open Access Journals (Sweden)

S. A. Pavlov

2018-01-01

Full Text Available At the choice of the mode of safe drying of grain mass it is necessary to consider its heterogeneity on moisture content. It is an undesirable factor of which it is necessary to get rid. When increase in moisture inconstant the stability of grain mass at storage decreases, there is a danger of emergence of heating, the overall performance of dryers and other processing equipment decreases, energy costs for seeds production rise. To eliminate this shortcoming located in a grain layer or grain stream the dried-up product should be mixed carefully for the best uniformity. However not uniformity on individual moisture content of separate grains will remain. For its decrease combination of lying with material concitation is used. Researches were conducted in batch-operated laboratory machine. The humidified seeds of sugar beet were blowed-through with the drying agent speed of 0.5 m/s and temperature of 45 degrees Celsius. Moisture removal between concitations did not exceed 2.5 percent for selection seeds and 3.0 percent for ordinary ones. Duration of the periods between concitations can be determined in the analytical way. Thickness of a layer of seeds allowing drying without concitation decreases on square dependence on increase in moisture content. A contact moisture exchange between the damp and dried caryopsides for 30 min and more make it possibledrop-off in the unevenness of drying up to 0.5 percent.

Life cycle environmental impacts of vacuum cleaners and the effects of European regulation

Energy Technology Data Exchange (ETDEWEB)

Gallego-Schmid, Alejandro, E-mail: alejandro.gallegoschmid@manchester.ac.uk; Mendoza, Joan Manuel F.; Jeswani, Harish Kumar; Azapagic, Adisa

2016-07-15

Energy efficiency of vacuum cleaners has been declining over the past decades while at the same time their number in Europe has been increasing. The European Commission has recently adopted an eco-design regulation to improve the environmental performance of vacuum cleaners. In addition to the existing directive on waste electrical and electronic equipment (WEEE), the regulation could potentially have significant effects on the environmental performance of vacuum cleaners. However, the scale of the effects is currently unknown, beyond scant information on greenhouse gas emissions. Thus, this paper considers for the first time life cycle environmental impacts of vacuum cleaners and the effects of the implementation of these regulations at the European level. The effects of electricity decarbonisation, product lifetime and end-of-life disposal options are also considered. The results suggest that the implementation of the eco-design regulation alone will reduce significantly the impacts from vacuum cleaners (37%–44%) by 2020 compared with current situation. If business as usual continued and the regulation was not implemented, the impacts would be 82%–109% higher by 2020 compared to the impacts with the implementation of the regulation. Improvements associated with the implementation of the WEEE directive will be much smaller (< 1% in 2020). However, if the WEEE directive did not exist, then the impacts would be 2%–21% higher by 2020 relative to the impacts with the implementation of the directive. Further improvements in most impacts (6%–20%) could be achieved by decarbonising the electricity mix. Therefore, energy efficiency measures must be accompanied by appropriate actions to reduce the environmental impacts of electricity generation; otherwise, the benefits of improved energy efficiency could be limited. Moreover, because of expected lower life expectancy of vacuum cleaners and limited availability of some raw materials, the eco-design regulation should

Life cycle environmental impacts of vacuum cleaners and the effects of European regulation

International Nuclear Information System (INIS)

Gallego-Schmid, Alejandro; Mendoza, Joan Manuel F.; Jeswani, Harish Kumar; Azapagic, Adisa

2016-01-01

Energy efficiency of vacuum cleaners has been declining over the past decades while at the same time their number in Europe has been increasing. The European Commission has recently adopted an eco-design regulation to improve the environmental performance of vacuum cleaners. In addition to the existing directive on waste electrical and electronic equipment (WEEE), the regulation could potentially have significant effects on the environmental performance of vacuum cleaners. However, the scale of the effects is currently unknown, beyond scant information on greenhouse gas emissions. Thus, this paper considers for the first time life cycle environmental impacts of vacuum cleaners and the effects of the implementation of these regulations at the European level. The effects of electricity decarbonisation, product lifetime and end-of-life disposal options are also considered. The results suggest that the implementation of the eco-design regulation alone will reduce significantly the impacts from vacuum cleaners (37%–44%) by 2020 compared with current situation. If business as usual continued and the regulation was not implemented, the impacts would be 82%–109% higher by 2020 compared to the impacts with the implementation of the regulation. Improvements associated with the implementation of the WEEE directive will be much smaller (< 1% in 2020). However, if the WEEE directive did not exist, then the impacts would be 2%–21% higher by 2020 relative to the impacts with the implementation of the directive. Further improvements in most impacts (6%–20%) could be achieved by decarbonising the electricity mix. Therefore, energy efficiency measures must be accompanied by appropriate actions to reduce the environmental impacts of electricity generation; otherwise, the benefits of improved energy efficiency could be limited. Moreover, because of expected lower life expectancy of vacuum cleaners and limited availability of some raw materials, the eco-design regulation should

Associations between psychosocial work environment and hypertension among non-Western immigrant and Danish cleaners

DEFF Research Database (Denmark)

Olesen, Kasper Vinther; Carneiro, Isabella G; Jørgensen, Marie B

2012-01-01

INTRODUCTION: Non-Western cleaners have reported better psychosocial work environment but worse health compared with their Danish colleagues. The aim of this study was to compare the association between psychosocial work environment and hypertension among non-Western immigrant cleaners and Danish...

Comparison of three control strategies for optimization of spray dryer operation

DEFF Research Database (Denmark)

Petersen, Lars Norbert; Poulsen, Niels Kjølstad; Niemann, Hans Henrik

2017-01-01

controllers for operation of a four-stage spray dryer. The three controllers are a proportional-integral (PI) controller that is used in industrial practice for spray dryer operation, a linear model predictive controller with real-time optimization (MPC with RTO, MPC-RTO), and an economically optimizing...... nonlinear model predictive controller (E-NMPC). The MPC with RTO is based on the same linear state space model in the MPC and the RTO layer. The E-NMPC consists of a single optimization layer that uses a nonlinear system of ordinary differential equations for its predictions. The PI control strategy has...... the production rate, while minimizing the energy consumption, keeping the residual moisture content of the powder below a maximum limit, and avoiding that the powder sticks to the chamber walls. We use an industrially recorded disturbance scenario in order to produce realistic simulations and conclusions...

Laboratory Development of A High Capacity Gas-Fired paper Dryer

Energy Technology Data Exchange (ETDEWEB)

Chudnovsky, Yaroslav [Gas Technology Institute, Des Plaines, IL (United States); Kozlov, Aleksandr [Gas Technology Institute, Des Plaines, IL (United States); Sherrow, Lester [Gas Technology Institute, Des Plaines, IL (United States)

2005-09-30

Paper drying is the most energy-intensive and temperature-critical aspect of papermaking. It is estimated that about 67% of the total energy required in papermaking is used to dry paper. The conventional drying method uses a series of steam-heated metal cylinders that are required to meet ASME codes for pressure vessels, which limits the steam pressure to about 160 psig. Consequently, the shell temperature and the drying capacity are also limited. Gas Technology Institute together with Boise Paper Solutions, Groupe Laparrier and Verreault (GL&V) USA Inc., Flynn Burner Corporation and with funding support from the U.S. Department of Energy, U.S. natural gas industry, and Gas Research Institute is developing a high efficiency gas-fired paper dryer based on a combination of a ribbon burner and advanced heat transfer enhancement technique. The Gas-Fired Paper Dryer (GFPD) is a high-efficiency alternative to conventional steam-heated drying drums that typically operate at surface temperatures in the 300ºF range. The new approach was evaluated in laboratory and pilot-scale testing at the Western Michigan University Paper Pilot Plant. Drum surface temperatures of more than 400ºF were reached with linerboard (basis weight 126 lb/3000 ft2) production and resulted in a 4-5 times increase in drying rate over a conventional steam-heated drying drum. Successful GFPD development and commercialization will provide large energy savings to the paper industry and increase paper production rates from dryer-limited (space- or steam-limited) paper machines by an estimated 10 to 20%, resulting in significant capital costs savings for both retrofits and new capacity.

Drying of Ceramic Hollow Bricks in an Industrial Tunnel Dryer: A Finite Volume Analysis

Directory of Open Access Journals (Sweden)

F Tavares

2016-10-01

Full Text Available This paper aims to study the drying of industrial hollow bricks in a tunnel dryer cross flow type. The theoretical model is based on mass and energy conservation equations applied to air and product. To validate the methodology, numerical and experimental results for the moisture content and the temperature of brick during the drying in an industrial scale are compared and a good correlation was obtained. Results of moisture content and temperature of the product, and temperature, relative humidity and absolute humidity of drying air as a function of drying time and position in the dryer are presented and analyzed.

Life cycle environmental impacts of vacuum cleaners and the effects of European regulation.

Science.gov (United States)

Gallego-Schmid, Alejandro; Mendoza, Joan Manuel F; Jeswani, Harish Kumar; Azapagic, Adisa

2016-07-15

Energy efficiency of vacuum cleaners has been declining over the past decades while at the same time their number in Europe has been increasing. The European Commission has recently adopted an eco-design regulation to improve the environmental performance of vacuum cleaners. In addition to the existing directive on waste electrical and electronic equipment (WEEE), the regulation could potentially have significant effects on the environmental performance of vacuum cleaners. However, the scale of the effects is currently unknown, beyond scant information on greenhouse gas emissions. Thus, this paper considers for the first time life cycle environmental impacts of vacuum cleaners and the effects of the implementation of these regulations at the European level. The effects of electricity decarbonisation, product lifetime and end-of-life disposal options are also considered. The results suggest that the implementation of the eco-design regulation alone will reduce significantly the impacts from vacuum cleaners (37%-44%) by 2020 compared with current situation. If business as usual continued and the regulation was not implemented, the impacts would be 82%-109% higher by 2020 compared to the impacts with the implementation of the regulation. Improvements associated with the implementation of the WEEE directive will be much smaller (impacts would be 2%-21% higher by 2020 relative to the impacts with the implementation of the directive. Further improvements in most impacts (6%-20%) could be achieved by decarbonising the electricity mix. Therefore, energy efficiency measures must be accompanied by appropriate actions to reduce the environmental impacts of electricity generation; otherwise, the benefits of improved energy efficiency could be limited. Moreover, because of expected lower life expectancy of vacuum cleaners and limited availability of some raw materials, the eco-design regulation should be broadened to reduce the impacts from raw materials, production and end

Increased Participation Among Cleaners as a Strategy to Improve Quality and Occupational Health

Directory of Open Access Journals (Sweden)

Therese Öhrling

2014-09-01

Full Text Available Like many other industries, today the cleaning industry is affected more than ever by competition and pressure toward low prices, which leads to a nonadvantageous situation for cleaners. These days many Swedish municipalities choose to outsource cleaning service in order to save money, although the situation for the cleaners appears to be worsening. The aim of this paper is to evaluate an alternative organizational structure within a Swedish public cleaning division to investigate how good work environment for cleaners can be combined with economical savings for a municipality. Like many other cleaning organizations, both national and international, the present cleaning division has been struggling for a long time with high levels of sick leave and early retirements. After years of unsuccessful attempts to improve the situation by reducing the physical load, cleaning managers made a decision to broaden their strategy by changing the structure of their organization. In this study, both qualitative and quantitative methods have been applied to identify and understand the effects of the organizational change, both on an individual level and on an organizational level. The results show that the organizational change, which leads to increased participation and autonomy for the cleaners, in combination with a high degree of social support, had a positive effect on job satisfaction, work motivation, and pride among the cleaners. Sick leave within the division has decreased, and both the quality and efficiency of the cleaning service have increased. It can be concluded that there are other alternative organizational structures that could be applied within the public sector and prove advantageous, both for the individual cleaners and for the municipality. Further research of similar organizational structures within the private cleaning sector is recommended.

Improving adsorption dryer energy efficiency by simultaneous optimization and heat integration

NARCIS (Netherlands)

Atuonwu, J.C.; Straten, G. van; Deventer, H.C. van; Boxtel, A.J.B. van

2011-01-01

Conventionally, energy-saving techniques in drying technology are sequential in nature. First, the dryer is optimized without heat recovery and then, based on the obtained process conditions, heat recovery possibilities are explored. This work presents a methodology for energy-efficient adsorption

Epitaxially grown polycrystalline silicon thin-film solar cells on solid-phase crystallised seed layers

Energy Technology Data Exchange (ETDEWEB)

Li, Wei, E-mail: weili.unsw@gmail.com; Varlamov, Sergey; Xue, Chaowei

2014-09-30

Highlights: • Crystallisation kinetic is used to analyse seed layer surface cleanliness. • Simplified RCA cleaning for the seed layer can shorten the epitaxy annealing duration. • RTA for the seed layer can improve the quality for both seed layer and epi-layer. • Epitaxial poly-Si solar cell performance is improved by RTA treated seed layer. - Abstract: This paper presents the fabrication of poly-Si thin film solar cells on glass substrates using seed layer approach. The solid-phase crystallised P-doped seed layer is not only used as the crystalline template for the epitaxial growth but also as the emitter for the solar cell structure. This paper investigates two important factors, surface cleaning and intragrain defects elimination for the seed layer, which can greatly influence the epitaxial grown solar cell performance. Shorter incubation and crystallisation time is observed using a simplified RCA cleaning than the other two wet chemical cleaning methods, indicating a cleaner seed layer surface is achieved. Cross sectional transmission microscope images confirm a crystallographic transferal of information from the simplified RCA cleaned seed layer into the epi-layer. RTA for the SPC seed layer can effectively eliminate the intragrain defects in the seed layer and improve structural quality of both of the seed layer and the epi-layer. Consequently, epitaxial grown poly-Si solar cell on the RTA treated seed layer shows better solar cell efficiency, V{sub oc} and J{sub sc} than the one on the seed layer without RTA treatment.

Design and Testing of a Natural Convection Solar Tunnel Dryer for Mango

Directory of Open Access Journals (Sweden)

Isaac Nyambe Simate

2017-01-01

Full Text Available A natural convection solar tunnel dryer comprising three major units, a solar collector unit, a drying unit, and a vertical bare flat-plate chimney, was constructed. No-load tests with a horizontal configuration of air entry into the collector resulted in a bidirectional air flow in the dryer. To correct this undesirable situation, an air guide at the collector was incorporated to ensure that air entered in a vertical direction. To investigate its performance, drying experiments with mango were carried out at the University of Zambia, Department of Agricultural Engineering. Uncertainties in the parameters measured in the experiment were analysed and quantified. The results showed that, under solar radiation between 568.4 and 999.5 W/m2, air temperature of up to 65.8°C was attained at the collector unit. The average relative humidity values were 30.8%, 6.4%, and 8.4% for the ambient, collector, and drying unit, respectively. Under these conditions, mango with an initial moisture content of 85.5% (wet basis was dried to 13.0% (wet basis in 9.5 hours. The collector, drying, and pick-up efficiencies were found to be 24.7%, 12.8%, and 35.0%, respectively. The average temperature difference between the chimney air and ambient air was 12.1°C, and this was sufficient in driving the flow of air through the dryer.

Thermal decomposition of uranylnitrate by the Spray-Dryer process

International Nuclear Information System (INIS)

Wildhagen, G.R.S.; Silva, G.C. da

1988-01-01

The proposal of this work consist in the thermal decomposition of uranyl nitrate solutions by the Spray-Dryer process aiming the production of highly reactive fluidized UO 3 , adequate for the use in posterior of reduction to UO 2 and hydrofluorination to UF 4 , in a fluidized bed for the obtention of UF 6 in the cicle of nuclear fuels. (author) [pt

Novel temperature control technique for a medicinal herb dryer system powered by a photovoltaic array

International Nuclear Information System (INIS)

Abd El-Shafy A Nafeh; Hanaa M Fargali; Faten H Fahmy; Mohamed A Hassan

2006-01-01

Each plant has its own optimal drying temperature, especially for the medicinal herbs, because they are sensitive to heat. If the drying temperature becomes more than the optimal value, some chemical reactions will occur and influence the quality of the dried herb, such as color, taste, and aroma. While if the drying temperature becomes lower than the optimal value, the drying process will slow down; and consequently an expected degradation in the quality of the herb may occur, due to insects and fungi infestation which increase in moist conditions. This paper presents a new temperature control technique for a medicinal herb dryer system. The technique fixes the drying temperature of the medicinal herbs at 40 degree C, even in cases of rapidly changing atmospheric conditions. The control of the dryer temperature is achieved through using the proportional integral (PI) controller. The designed dryer contains two systems, which are the thermal and the electrical systems. The thermal system is designed to heat the drying air by using the solar energy and bio-gas fuel. Whereas, the electrical system, which contains a photovoltaic (PV) modules and a battery, is designed to supply the different electrical loads of the dryer system. The control technique is investigated through simulation work by using MATLAB-SIMULINK. The simulation results indicate the high capability of the proposed technique in controlling the drying temperature, even in cases of rapidly changing atmospheric conditions

Fluid bed dryer and Aeropep solidification system. Amendment 1 to topical report

International Nuclear Information System (INIS)

1975-01-01

Information is presented on interfaces between the aerojet fluid bed dryer and the liquid radwaste system, plant ventilation system, and radioactive solid waste handling system for BWR and PWR type reactors. (U.S.)

Determination of stresses caused by fluctuation of acoustic load in the steam dryers of a BWR

International Nuclear Information System (INIS)

Centeno P, J.; Quezada G, S.; Prieto G, A.; Vazquez R, A.; Espinosa P, G.; Nunez C, A.

2014-10-01

The extended power up-rate (EPU) in a nuclear power plant cause various problems in BWR components also in the steam system. This due to increased steam flow generated in the reactor and is conveyed to the turbine by the four main steam lines (MSL). One of the most serious problems is the generation of acoustic pressure loads in the metal structure of the steam dryer which eventually leads to fatigue failure and even the appearance of cracks, and in turn it causes loose parts that are entrained by the steam and transported in the MSL. This problem is due to the fluctuation of load acoustics caused by the union of the safety or relief valves (SRV) with the MSL, spreading through these to reach the reactor pressure vessel (RPV) where the effect of resonance of the acoustic wave is amplified and impacts directly in the supporting structure of the steam dryer, skirt and the panels where the mixture liquid-steam is dried, by centrifugation effect and runoff of liquid water. Efforts in the steam dryer operating conditions of EPU for two cases will be analyzed in this work, the first is before the installation of Acoustic Side Branch (ASB), and in the second case we consider the installation of said ASB in the standpipes of SRV. The analysis was performed with numerical experiments on a platform for computational fluid dynamics with virtual geometries previously designed based on the actual components of the reactor and steam system. The model to study is delimited by the top of the RPV, the steam dryer and a section of each of the four MSL with ten standpipes of SRV. With the obtained data and considering the mechanical-structural properties of the steam dryer material, we can evaluate the mechanical resistance to impacts by acoustic pressure load and its possible deformation or cracking. (Author)

Modeling of thermal mode of drying special purposes ceramic products in batch action chamber dryers

Science.gov (United States)

Lukianov, E. S.; Lozovaya, S. Yu; Lozovoy, N. M.

2018-03-01

The article is devoted to the modeling of batch action chamber dryers in the processing line for producing shaped ceramic products. At the drying stage, for various reasons, most of these products are warped and cracked due to the occurrence of irregular shrinkage deformations due to the action of capillary forces. The primary cause is an untruly organized drying mode due to imperfection of chamber dryers design specifically because of the heat-transfer agent supply method and the possibility of creating a uniform temperature field in the whole volume of the chamber.

Integrated Technology Air Cleaners (ITAC): Design and Evaluation

Energy Technology Data Exchange (ETDEWEB)

Fisk, William J.; Cohn, Sebastian; Destaillats, Hugo; Henzel, Victor; Sidheswaran, Meera; Sullivan, Douglas P.

2013-09-13

The primary objective of this project was to design, build, and test an air cleaner for residential use with the potential to substantially improve indoor air quality, or maintain indoor air quality unchanged, when outdoor air ventilation rates are reduced to save energy. Two air cleaners were designed and fabricated. The design targets for airflow rate, fan power, and projected cost were met. In short term laboratory studies, both units performed as expected; however, during field studies in homes, the formaldehyde removal performance of the air cleaners was much lower than expected. In subsequent laboratory studies, incomplete decomposition of some indoor air volatile organic compounds, with formaldehyde as a product of partial decomposition of volatile organic compounds, was confirmed as the explanation for the poor formaldehyde removal performance in the field studies. The amount of formaldehyde produced per unit of decomposition of other volatile organic compounds was substantially diminished by increasing the amount of catalyst on the filter and also by decreasing the air velocity. Together, these two measures reduced formaldehyde production, per unit destruction of other volatile organic compounds, by a factor of four, while increasing the removal efficiency of volatile organic compounds by a factor of 1.4. A company with a southern California office is conducting studies in conjunction with Lawrence Berkeley National Laboratory, with the goal of incorporating the ITAC catalytic air cleaning technology in their future commercial products.

The local implementation of clean(er) fuels policies in Europe. A Handbook with guidelines. Final version

International Nuclear Information System (INIS)

Mulder, F.; Amara, Sliman Abu; Uustal, M.; Pelkmans, L.; Devriendt, N.; Rogulska, M.; Defranceschi, P.

2009-05-01

This handbook aims to guide the local/regional governments all over Europe who are involved in implementing clean(er) fuel policies in transport. The general challenge these governments are facing is how local policies on clean(er) fuels and vehicles can be made operational. Hence, how can the step be made from a vision on the strategic policy level, to a vision on the implementation of these policies. A local/regional policy on clean(er) fuels and vehicles is commonly part of the larger category 'sustainable transport policy', which in itself is part of a broader local environmental policy. The encompassing local/regional sustainable mobility policy will in most cases be based on the three well known main policy aims in this area: CO2 reduction; Improving the local air quality; and Improving the security of supply (locally often less stressed). This handbook will focus on the actual implementation of a clean(er) fuels and vehicles policy. It will describe the main challenges and how these can be overcome. It will describe how the market conditions for clean(er) fuels and vehicles can be created by establishing the vital market elements and which process is required to do so. And it will show how local enterprises can be involved and what the role of the local governments in this process can be. In order to identify the local success factors in overcoming the main challenges for implementation, case studies have been carried out in three European cities, namely Stockholm (Sweden), Graz (Austria) and Lille (France). The choice of these cities was based on their successes in implementing clean(er) fuel policies (although they followed different paths) and the fact that they managed to achieve ambitious clean(er) fuel/ clean(er) vehicle targets. These cities may thus be considered as ?good practice examples?. The case studies are based on existing literature, on multiple stakeholders? interviews in all three cities, and on two small surveys. The objectives of this

Economic Optimization of Spray Dryer Operation using Nonlinear Model Predictive Control

DEFF Research Database (Denmark)

Petersen, Lars Norbert; Poulsen, Niels Kjølstad; Niemann, Hans Henrik

2014-01-01

In this paper we investigate an economically optimizing Nonlinear Model Predictive Control (E-NMPC) for a spray drying process. By simulation we evaluate the economic potential of this E-NMPC compared to a conventional PID based control strategy. Spray drying is the preferred process to reduce...... the water content for many liquid foodstuffs and produces a free flowing powder. The main challenge in controlling the spray drying process is to meet the residual moisture specifications and avoid that the powder sticks to the chamber walls of the spray dryer. We present a model for a spray dryer that has...... been validated on experimental data from a pilot plant. We use this model for simulation as well as for prediction in the E-NMPC. The E-NMPC is designed with hard input constraints and soft output constraints. The open-loop optimal control problem in the E-NMPC is solved using the single...

performance evaluation of a pebble bed solar crop dryer abstract

African Journals Online (AJOL)

Dr Obe

The open-air sun drying is prevalent and very common in the rural areas. Farmers spread their agricultural produce such as maize, cassava, pepper, tomatoes etc. ... drying system. The abundance of solar radiation in. Nigeria could make crop drying with solar dryers very easy and simple. Economic appraisal of solar drying ...

Ultra-Stable, New Generation Q-Switched Monolithic Laser Cleaners for Fine Art Conservation

Science.gov (United States)

Brioschi, F.; Salvadeo, P.

The increasing use of laser cleaners in fine art conservation boosts the demand on improvements of the laser performances. More power and more wavelengths are required by the current applications, while laser should be more reliable, rugged and compact. The characteristics and performances of a new generation of laser cleaners are presented as a result of a dedicated research and development program.

Determination and ranking cleaner production criteria by using analytic hierarchy process (Case study: Latif paper products company

Directory of Open Access Journals (Sweden)

Yaghob Asadizadeh

2018-02-01

Full Text Available Cleaner production process is an environmentally friendly approach that attempts to reduce waste and energy consumption then reduce environmental pollutions of industrial processes to provide the possibility of sustainable production in industrial units. To achieve this goal and alignment with cleaner production strategies, paper industries should consider reducing wastes of production processes and irregular consumption of energy as a priority in their programs. In this research Analytic Hierarchy Process has been applied and a three level hierarchy model was structured to facilitate the cleaner production process in Latif paper products firm. Using a literature review and field study, the proposed model provided a framework for cleaner production implementation in the firm. Results showed priorities of the main criteria of cleaner production are process change, product modification, implementation of preventive maintenance system, resititution and man force capitals respectively. Process change criterion allocated 40 percent of the total weighing value and has the highest priority in implementation of cleaner production strategy. Existence of industrial automation and its technology level which is a sub criterion of process change has the highest priority among 31 sub criteria. Also some of higher priority sub criteria such as use of higher quality inclusion and implementation of calibration system are related to process change. Therefore, to achieve cleaner production goals and implementation of its strategic objectives it is necessary to pay more attention to this criterion. Inconsistency ratio of the research is 0.06 which indicates the results are compatible. The results of this research can be used to accelerate the implementation of cleaner production process in Iran’s pulp and paper industry.

Performance Evaluation of an Active Solar Dryer Equipped with an Auxilliary Electrical Heater and Heat Recovery System

International Nuclear Information System (INIS)

Pourghasemi Ranjbar, M.; Alavi Naeini, N.; Mortezapour, H.

2016-01-01

Drying is a very sophisticated process which consumes a large amount of energy. Solar energy can be used as an alternative or supplementary energy source to fossil fuels. Solar dryers are common ways for saving fossil fuel consumption during agricultural products drying. In this study, the performance of an active solar dryer equipped with an energy recovery system was investigated at three levels of drying air temperature. The results showed that the energy recovery system was able to increase inlet air temperature by 16.8, 18.5 and 18.9 ° C at drying temperatures of 55, 65 and 75 ℃, respectively. Meanwhile 47.8, 42.9 and 40.9 percents of the dryer exhaust air energy were recovered respectively at these conditions which subsequently led to a reduction of 30.7, 19.2 and 14.7 percents in electrical heater energy consumption.

Research on Duct Flow Field Optimisation of a Robot Vacuum Cleaner

Directory of Open Access Journals (Sweden)

Xiao-bo Lai

2011-11-01

Full Text Available The duct of a robot vacuum cleaner is the length of the flow channel between the inlet of the rolling brush blower and the outlet of the vacuum blower. To cope with the pressure drop problem of the duct flow field in a robot vacuum cleaner, a method based on Pressure Implicit with Splitting of Operators (PRISO algorithm is introduced and the optimisation design of the duct flow field is implemented. Firstly, the duct structure in a robot vacuum cleaner is taken as a research object, with the computational fluid dynamics (CFD theories adopted; a three-dimensional fluid model of the duct is established by means of the FLUENT solver of the CFD software. Secondly, with the k-∊ turbulence model of three-dimensional incompressible fluid considered and the PRISO pressure modification algorithm employed, the flow field numerical simulations inside the duct of the robot vacuum cleaner are carried out. Then, the velocity vector plots on the arbitrary plane of the duct flow field are obtained. Finally, an investigation of the dynamic characteristics of the duct flow field is done and defects of the original duct flow field are analysed, the optimisation of the original flow field has then been conducted. Experimental results show that the duct flow field after optimisation can effectively reduce pressure drop, the feasibility as well as the correctness of the theoretical modelling and optimisation approaches are validated.

Research on Duct Flow Field Optimisation of a Robot Vacuum Cleaner

Directory of Open Access Journals (Sweden)

Xiao-bo Lai

2011-11-01

Full Text Available The duct of a robot vacuum cleaner is the length of the flow channel between the inlet of the rolling brush blower and the outlet of the vacuum blower. To cope with the pressure drop problem of the duct flow field in a robot vacuum cleaner, a method based on Pressure Implicit with Splitting of Operators (PRISO algorithm is introduced and the optimisation design of the duct flow field is implemented. Firstly, the duct structure in a robot vacuum cleaner is taken as a research object, with the computational fluid dynamics (CFD theories adopted; a three‐dimensional fluid model of the duct is established by means of the FLUENT solver of the CFD software. Secondly, with the k‐ε turbulence model of three‐ dimensional incompressible fluid considered and the PRISO pressure modification algorithm employed, the flow field numerical simulations inside the duct of the robot vacuum cleaner are carried out. Then, the velocity vector plots on the arbitrary plane of the duct flow field are obtained. Finally, an investigation of the dynamic characteristics of the duct flow field is done and defects of the original duct flow field are analysed, the optimisation of the original flow field has then been conducted. Experimental results show that the duct flow field after optimisation can effectively reduce pressure drop, the feasibility as well as the correctness of the theoretical modelling and optimisation approaches are validated.

Method of aeration disinfecting and drying grain in bulk and pretreating seeds and a transverse blow silo grain dryer therefor

Science.gov (United States)

Danchenko, Vitaliy G [Dnipropetrovsk, UA; Noyes, Ronald T [Stillwater, OK; Potapovych, Larysa P [Dnipropetrovsk, UA

2012-02-28

Aeration drying and disinfecting grain crops in bulk and pretreating seeds includes passing through a bulk of grain crops and seeds disinfecting and drying agents including an ozone and air mixture and surrounding air, subdividing the disinfecting and drying agents into a plurality of streams spaced from one another in a vertical direction, and passing the streams at different heights through levels located at corresponding heights of the bulk of grain crops and seeds transversely in a substantially horizontal direction.

Development of an active solar crop dryer: design analysis and ...

African Journals Online (AJOL)

The design analysis and performance evaluation of an active solar crop dryer was undertaken by drying marched cassava. The drying rate, system drying, collector and pick-up efficiencies were 1.6kg/day (14%/day), 9%, 46% and 29% respectively. Comparatively, the drying rate for sun drying was 0.9kg/day. The collector ...

Vibration Analysis for Steam Dryer of APR1400 Steam Generator

Energy Technology Data Exchange (ETDEWEB)

Han, Sung-heum; Ko, Doyoung [KHNP CRI, Daejeon (Korea, Republic of); Cho, Minki [Doosan Heavy Industry, Changwon (Korea, Republic of)

2016-10-15

This paper is related to comprehensive vibration assessment program for APR1400 steam generator internals. According to U.S. Nuclear Regulatory Commission, Regulatory Guide 1.20 (Rev.3, March 2007), we conducted vibration analysis for a steam dryer as the second steam separator of steam generator internals. The vibration analysis was performed at the 100 % power operating condition as the normal operation condition. The random hydraulic loads were calculated by the computational fluid dynamics and the structural responses were predicted by power spectral density analysis for the probabilistic method. In order to meet the recently revised U.S. NRC RG 1.20 Rev.3, the CVAP against the potential adverse flow effects in APR1400 SG internals should be performed. This study conducted the vibration response analysis for the SG steam dryer as the second moisture separator at the 100% power condition, and evaluated the structural integrity. The predicted alternating stress intensities were evaluated to have more than 17.78 times fatigue margin compared to the endurance limit.

Drying of carrot slices in a triple pass solar dryer

Directory of Open Access Journals (Sweden)

Seshachalam Kesavan

2017-01-01

Full Text Available An indirect triple pass forced convection solar dryer was developed and its performance was evaluated for drying of carrot slices. The drying experiments were carried out under the meteorological conditions of Coimbatore city in India during the year 2016. The experimental set-up consists of a blower, triple pass packed bed air collector (using sand with wire mesh absorber plate, and a drying chamber. The air mass flow rate was optimized to 0.062 kg/s. The initial moisture content of the carrot slices was reduced from 87.5% (on wet basis to the final moisture content of 10% (wet basis in 6 h duration. The thin layer drying characteristics were analyzed using twelve mathematical models available in open literature. The results showed that the pick-up efficiency of the dryer was varied in the range between 14 and 43% with an average air collector thermal efficiency of 44% during the experimentation. The drying characteristics of carrot slices was predicted with good degree of accuracy using Wang and Singh drying model.

The association between health and sickness absence among Danish and non-Western immigrant cleaners in Denmark.

Science.gov (United States)

Carneiro, Isabella G; Rasmussen, Charlotte D N; Jørgensen, Marie B; Flyvholm, Mari-Ann; Olesen, Kasper; Madeleine, Pascal; Ekner, Dorte; Søgaard, Karen; Holtermann, Andreas

2013-05-01

The aim of the study is to investigate the association between health and sickness absence among Danish and non-Western immigrant cleaners in Denmark. This study is based on a cross-sectional analysis of baseline data from 2007 to 2008. The study population includes 276 cleaners, 144 Danish and 132 non-Western immigrant cleaners. Cumulative sickness absences during a 6-month period from administrative records were subdivided into no sickness absence (0 days), low occurrence of sickness absence (1-10 days) and high occurrence of sickness absence (over 10 days). Measures of health consisted of self-report and objective assessments. The relationship between sickness absence and health was analyzed through multinomial logistic regression, stratified by immigrant status. For both Danish and non-Western immigrant cleaners, poor self-reported health was significantly related to high occurrence of sickness absence. Among Danish cleaners, high blood pressure was related to high occurrence of sickness absence. Among non-Western immigrant cleaners, total body pain and having one or more diagnosed chronic disease were related to high occurrence of sickness absence. No association between health and low occurrence of sickness absence was found. The findings confirm the importance of health for high occurrence of sickness absence, in both ethnic groups. Moreover, low occurrence of sickness absence was not related to the health conditions investigated.

On Cleaner Technologies in a Transboundary Pollution Game

NARCIS (Netherlands)

Benchekroun, H.; Ray Chaudhuri, A.

2009-01-01

We show that in a non-cooperative transboundary pollution game, a cleaner technology (i.e., a decrease in the emission to output ratio) induces each country to increase its emissions and ultimately can yield a higher level of pollution and reduce social welfare.

A Case Study of Air Cleaner by the Intelligent Interaction and Emotion

Science.gov (United States)

Cao, Huai; Sun, Yuwen

2018-02-01

The pure and fresh air can not only contribute to our physical and mental health, but also can be beneficial to ease the pressure and relax the mood. The vertical intelligent air cleaner can remove the harmful gases from the air and absorb the suspended particles in the air, especially all kinds of the bacteria and viruses. The air cleaner is good for improving the air quality of the indoor and maintaining the health of the people. The designing of the vertical air cleaner is as follows: The designing of the vertical intelligent make full use of the developed air purification technology. The smart home is inserted into the work. Simultaneously, in the aspect of the design of intelligent products, the intelligent interactive processes are scientifically planned. Moreover, the emotional design and the user experience are fully considered, which can enhance the comprehensive design ability.

Performance of mechanically shaken indirect contact atmospheric dryer in drying pastelike materials

Directory of Open Access Journals (Sweden)

K. P. Melo

2004-09-01

Full Text Available Pastelike materials are encountered in many technological processes in chemical, pharmaceutical, foodstuff and natural product industries. The most important factor in the drying of this type of materials is the nature of the moisture bonding that occurs. Because of the different characteristics of pastes, it is impossible to recommend a universal type of dryer for all of these materials. Some of the dryers available provide only indirect contact with the drying agent (heat and also maintain constant moisture with a system of rotating paddles. We evaluated the performance of this type by studying the dryer kinetics curves for ground coffee under a variety of operational conditions of moisture load of material, temperature of the heating plate, intensity of the mechanical mixing of the moisture material, and initial moisture. The effects of these parameters (except for moisture were studied using a 2³ factorial design. According the analyses of the kinetics drying curves, was observed that the increase in the temperature of the plate and rotation as well as the decrease in the load facilitates more effective removal of moisture. In statistical analysis was determined that the load of the material and the heating plate temperature influence the final moisture content of the material and plate temperature modifies the final temperature of the solid. Also, was suggested linear models from the factorial design to describe the process of drying coffee grounds satisfactorily.

Guide to cleaner coal technology-related web sites

Energy Technology Data Exchange (ETDEWEB)

Davidson, R; Jenkins, N; Zhang, X [IEA Coal Research - The Clean Coal Centre, London (United Kingdom)

2001-07-01

The 'Guide to Cleaner Coal Technology-Related Web Sites' is a guide to web sites that contain important information on cleaner coal technologies (CCT). It contains a short introduction to the World Wide Web and gives advice on how to search for information using directories and search engines. The core section of the Guide is a collection of factsheets summarising the information available on over 65 major web sites selected from organizations worldwide (except those promoting companies). These sites contain a wealth of information on CCT research and development, technology transfer, financing and markets. The factsheets are organised in the following categories. Associations, research centres and programmes; Climate change and sustainable development; Cooperative ventures; Electronic journals; Financial institutions; International organizations; National government information; and Statistical information. A full subject index is provided. The Guide concludes with some general comments on the quality of the sites reviewed.

Visibility and Social Recognition as Psychosocial Work Environment Factors among Cleaners in a Multi-Ethnic Workplace Intervention

Directory of Open Access Journals (Sweden)

Kirsten Hviid

2012-12-01

Full Text Available This article focuses on the psychosocial work environment of immigrant cleaners at a Danish workplace. Today, many cleaners working in Danish cleaning jobs are women from the established immigrant communities, but also labour migrants from the newer EU member states have found their way to the cleaning industry. Studies have drawn attention to immigrants’ low position in the cleaning industry and their increased risk of work injuries. This article is based on a case study of an intervention called “Make a Difference” designed to improve the work environment among cleaners at a multi-ethnic workplace. We used semi-structured interviews, photo logs, observation and participation to investigate how the cleaners experienced their work environment. The cleaners reported an overload of heavy work, related to the concept of a classroom’s “readiness for cleaning”, and they expressed strained social relations and communication in addition to a lack of social recognition and invisibility at the workplace, a school. We analysed these psychosocial work environmental problems by investigating the different forms of social relationships and communication within the group of cleaners, and between the cleaners and the teachers and pupils at the school. Moreover, we discussed why the intervention, based on training of language and cleaning skills and social interaction, only partially improved the cleaners’ psychosocial work environment problems. In this article, we argue that social divisions based on ethnicity between the new and the established group of cleaners, combined with their marginal position and poor work organisation at the school, reinforced the cleaners’ experiences of psychosocial work environment problems. This article suggests that increased effort towards social inclusion at work and improved work organisation, especially for the new labour migrants from newer EU-countries, should be considered.

Evaluation of heat stress in dry cleaner units:A case study in Qom, Iran

Directory of Open Access Journals (Sweden)

Javad Malakouti

2016-04-01

Full Text Available Background & Aims of the Study: Nowadays, heat stress is one of the most harmful physical agents in workplaces. According to the consequences of heat stress and have no information about it in Qom dry cleaner units, Iran, this study have been designed to evaluate the heat stress among workers of dry cleaner units in Qom province of Iran, in Jul-Aug 2011. Materials & Methods: This cross-sectional study was conducted in 113 units of active dry cleaner units. WBGT (Wet Bulb Globe Temperature index was selected for heat stress evaluation. In order to measure the requisite parameters, WBGT meter made of Casella Company had been used according to ISO 7243. Data had been analyzed according to Occupational Exposure Limits (OELs with SPSS V.16, using analysis of variance, independent T and LSD tests. Results: The average of WBGT index in Qom dry cleaner units of Iran were 28.98±1.64 °C. The average of WBGT index in 66.4% of units was up to 28°C. The average of relative humidity was 42.86%, the average of wet bulb temperature and globe temperature were 25.56°C and 36.72°C, respectively. The findings showed a significant correlation between the average of WBGT index and the standard recommendation level (p<0.0001. In dry cleaner units with less than 10 m2 area, heat stress was higher than other units  significantly (p<0.05. Conclusions: Heat stress in many dry cleaner units in Qom, Iran, was more than recommended OELs. Because of wet bulb and globe temperature in units were high value, the most important measures to heat controls, are technical engineering controls such as  radiation shield, insulation on boilers and modify the cooling systems.

What characterizes cleaners sustaining good musculoskeletal health after years with physically heavy work?

DEFF Research Database (Denmark)

Holtermann, A; Blangsted, A K; Christensen, H

2009-01-01

OBJECTIVES: The aim of this case-control study was to investigate characteristics of cleaners with good musculoskeletal health after years with physically heavy work. METHODS: One hundred and 41 female seniority cleaners participated. Twenty-five reported no musculoskeletal symptoms, whereas 83...... reported severe symptoms in the low back, neck shoulders or upper limbs. The groups were of matching age, height, body weight and seniority (19 years). Muscular strength was recorded by isometric maximal voluntary contractions on a day without pain. Exposure to physical risk factors at work, psychosocial...... work factors, and leisure time physical activity were assessed by a postal questionnaire. RESULTS: Cleaners with good musculoskeletal health were not reporting different exposure to physical risk factors at work or leisure time physical activity, but had higher muscular strength and reported higher...

7 CFR 2902.18 - Hand cleaners and sanitizers.

Science.gov (United States)

2010-01-01

..., DEPARTMENT OF AGRICULTURE GUIDELINES FOR DESIGNATING BIOBASED PRODUCTS FOR FEDERAL PROCUREMENT Designated... the purposes of this rule. (b) Minimum biobased content. The minimum biobased content requirement for all hand cleaners and/or sanitizers shall be based on the amount of qualifying biobased carbon in the...

Life cycle energy metrics and CO 2 credit analysis of a hybrid photovoltaic/thermal greenhouse dryer

OpenAIRE

P. Barnwal; G. N. Tiwari

2008-01-01

In this paper, life cycle energy metrics, such as energy payback time (EPBT), energy production factor (EPF) and life cycle conversion efficiency (LCCE), and mitigation of CO 2 emissions for a hybrid photovoltaic/thermal (PV/T) greenhouse dryer have been analyzed. The hybrid PV/T greenhouse (roof type even span) dryer, designed and constructed at Solar Energy Park, Indian Institute of Technology, New Delhi (28°35′N, 77°12′E, 216 m above MSL), India, has a 2.50 m × 2.60 m floor area, 1.80 m ce...

Control of respirable particles and radon progeny with portable air cleaners

International Nuclear Information System (INIS)

Offermann, F.J.; Sextro, R.G.; Fisk, W.J.; Nazaroff, W.W.; Nero, A.V.; Revzan, K.L.; Yater, J.

1984-02-01

Eleven portable air cleaning devices have been evaluated for control of indoor concentrations of respirable particles and radon progeny. Following injection of cigarette smoke and radon in a room-size chamber, decay rates for particles and radon progeny concentrations were measured with and without air cleaner operation. Particle concentrations were obtained for total number concentration and for number concentration by particle size. In tests with no air cleaner the natural decay rate for cigarette smoke was observed to be 0.2 hr -1 . Air cleaning rates for particles were found to be negligible for several small panel-filters, a residential ion-generator, and a pair of mixing fans. The electrostatic precipitators and extended surface filters tested had significant particle removal rates, and a HEPA-type filter was the most efficient air cleaner. The evaluation of radon progeny control produced similar results; the air cleaners which were effective in removing particles were also effective in removing radon progeny. At low particle concentrations plateout of the unattached radon progeny is an important removal mechanism. Based on data from these tests, the plateout rate for unattached progeny was found to be 15 hr -1 . The unattached fraction and the overall removal rate due to deposition of attached and unattached nuclides have been estimated for each radon decay product as a function of particle concentration. While air cleaning can be effective in reducing total radon progeny, concentrations of unattached radon progeny can increase with increasing air cleaning. 39 references, 26 figures, 9 tables

Natural convection solar crop dryers in Kenya: Theory and practical application. African Energy Programme research report series no. 3

International Nuclear Information System (INIS)

Othieno, H.

1987-01-01

The African Energy Programme (AEP) was established by the Commonwealth Science Council (CSC) to strengthen Africa's scientific and technical capabilities to develop and utilise the continent's enormous renewable energy resources to assist its socio-economic development. The AEP was conceived at a regional workshop held at Arusha, Tanzania in 1979, at which African researchers met to share their experiences of and explored the feasibility of establishing a collaborative regional R and D programme to develop and adapt technologies appropriate to the specific needs of the participating countries. The AEP researchers accorded the highest priority to seeking solutions to the energy problems of Africa's predominantly rural populations and identified eight project areas as the nodes for regional collaborative research and development: 1. Biogas for rural development; 2. Wood/Charcoal production and utilisation; 3. Solar crop drying; 4. Solar thermal heating and cooling; 5. Wind electricity generation; 6. Wind water pumping; 7. Resources Assessments; 8. Energy policy and planning. The primary goal of the AEP activities were to develop indigenous national capabilities to enable the examination and application of technological solutions appropriate to the unique problems and socio-cultural environments of each country. However, the severe limitations on expertise and the broad similarity of many of the critical problems favoured regional R and D cooperation around common techniques and methodologies in each project area. This work has made a significant contribution to Science and Technology. Prior to this work there was no detailed information in natural convection solar dryers. This work has exposed a number of critical design factors which must be considered in order to design an efficient dryer. Buoyancy-induced pressure inside the dryer, problems of multiple radiative heat exchange in the heater and cooling effects of wind have been studied in detail. The final dryer

Natural convection solar crop dryers in Kenya: Theory and practical application. African Energy Programme research report series no. 3

Energy Technology Data Exchange (ETDEWEB)

Othieno, H [Kenyatta University, Nairobi (Kenya)

1987-07-01

The African Energy Programme (AEP) was established by the Commonwealth Science Council (CSC) to strengthen Africa's scientific and technical capabilities to develop and utilise the continent's enormous renewable energy resources to assist its socio-economic development. The AEP was conceived at a regional workshop held at Arusha, Tanzania in 1979, at which African researchers met to share their experiences of and explored the feasibility of establishing a collaborative regional R and D programme to develop and adapt technologies appropriate to the specific needs of the participating countries. The AEP researchers accorded the highest priority to seeking solutions to the energy problems of Africa's predominantly rural populations and identified eight project areas as the nodes for regional collaborative research and development: 1. Biogas for rural development; 2. Wood/Charcoal production and utilisation; 3. Solar crop drying; 4. Solar thermal heating and cooling; 5. Wind electricity generation; 6. Wind water pumping; 7. Resources Assessments; 8. Energy policy and planning. The primary goal of the AEP activities were to develop indigenous national capabilities to enable the examination and application of technological solutions appropriate to the unique problems and socio-cultural environments of each country. However, the severe limitations on expertise and the broad similarity of many of the critical problems favoured regional R and D cooperation around common techniques and methodologies in each project area. This work has made a significant contribution to Science and Technology. Prior to this work there was no detailed information in natural convection solar dryers. This work has exposed a number of critical design factors which must be considered in order to design an efficient dryer. Buoyancy-induced pressure inside the dryer, problems of multiple radiative heat exchange in the heater and cooling effects of wind have been studied in detail. The final dryer

Drying of Rhinacanthus nasutus (Linn. Kurz. using a solar dryer incorporated with a backup thermal energy storage from wood combustion

Directory of Open Access Journals (Sweden)

Perapong Tekasakul

2006-05-01

Full Text Available An indirect, natural convection, solar cabinet dryer incorporated with a backup thermal energy storage from wood combustion was designed and tested with the Thai herb, Rhinacanthus nasutus (Linn. Kurz. Most of Thai herbs are widely used as traditional medicine and drying is an initial step in the production process. Solar dryer with a biomass backup heating system is the most feasible solution to drying in Thailand. In this work, a 4 m x 5 m solar collector was used to absorb solar radiation for heating the incoming air during the daytime, while a biomass burner was used to supply heat when solar energy was not possible. Heat from fuelwood combustion was accumulated in the thermal storage system made of bricks, and was used to heat up the incoming air. Results showed that the herb was dried uniformly and the temperature inside the drying cabinet could be maintained above 50ºC for more than 10 hours. Thermal efficiency when using solar energy was 10.5%, but the value was less than 1% when using the heat from biomass burning. This resulted from the low moisture content of the products after being dried by the solar energy. The dryer is beneficial to the operators, particularly in southern Thailand, where continuous drying is required. This dryer is by no means limited to drying of the herb. Currently, four dryers of the same model have been used by farmer groups in southern Thailand for drying bananas, several types of herbs, fish, and other products. In economic consideration, its payback period is 5.5 years when compared with the LPG-equipped dryer. When the total cost and production capacity are considered, its payback period is about 6 years.

The Urban Function of the Infraordinary: Dry Cleaners as Social Vertexes

DEFF Research Database (Denmark)

Lunde Nielsen, Espen

2015-01-01

of social coexistence that has ‘a function that is separate from their practical use’ (Jorn 1954). A London dry cleaner serves as testing ground, employing critical spatial practices and creative writing as research tools. The dry cleaner does not simply clean clothes, but is a social vertex and physical...... interface through which (non-)events unfold, trajectories thickens and people of the neighbourhood coexists as familiar strangers (Milgram 2010; Paulos and Goodman 2004) through events in real-time and deposits over time. It is a semi-public space and an implosion of the external neighbourhood, partly...

Cleaners in reducing the hazards of indoor radon decay products

International Nuclear Information System (INIS)

Montassier, N.; Hopke, P.K.; Shi, Y.; Wasiolek, P.; McCallum, B.

1992-01-01

The objective of this study was to evaluate the influence of three types of air cleaners on the concentration and size distribution of radon progeny in a normally occupied house. Using an automated, semi-continuous, graded-screen array system and a radon monitor, the activity size distribution and radon concentration was measured and the exposure of the occupants of the home to radon could be assessed. The dose model developed as part of the recently released U.S. National Academy of Sciences report was used to related the exposure to deposited dose in the tissue of the bronchial epithelium. Thus, the effectiveness of the air cleaners in reducing both exposure and dose were evaluated. (author)

Psychosocial work environment among immigrant and Danish cleaners

DEFF Research Database (Denmark)

Olesen, Kasper; Carneiro, Isabella G; Jørgensen, Marie B

2012-01-01

Non-Western cleaners have been shown to have poorer health than their Danish colleagues. One reason could be a poorer psychosocial work environment. However, it is unknown if differences in self-reported psychosocial work environment exist between non-Western and Danish workers within the same so...

Cleaner Production: A Growing Movement in Brazilian Companies

Directory of Open Access Journals (Sweden)

Oduvaldo Vendrametto

2010-03-01

Full Text Available Cleaner Production (CP is gaining emphasis in both world and Brazilian production sectors. Nature’s warnings indicating the exhaustion of any capacity to absorb and regenerate waste, stricter legislation regarding pollution emitters, market competitiveness associated with environmental and social responsibility cause concerns and lead to actions to reduce aggressions against the environment. This paper shows evidence of this concern and presents cases in which a large automotive industry, acting as a partner to suppliers, promotes changes in how it delivers its products, eliminating large cardboard, plastic and wood packaging. A small company had a similar initiative, reducing the use of cardboard and plastic packaging. More important is the revelation of a widely dispersed, yet growing and incremental movement of responsibilities among companies.The benefits of cleaner production implementation were evaluated by confronting environmental and financial assessment. For the ambient evaluation, it will be used methodology of Material Intensity (Wuppertal Institute, a.

Sanitary condition of electrical hand dryers in toilets of shopping centres in Kraków

Directory of Open Access Journals (Sweden)

Anna Lenart-Boroń

2015-06-01

Full Text Available Introduction. Shopping habits have changed over the past several years and consumers choose shopping centres, where they can spend time and visit restaurants. People usually wash hands before meals, but toilets in shopping centres are visited by hundreds of users every day which makes their cleanliness questionable. Therefore, the aim of this study was to assess the sanitary condition of electrical hand dryers in toilets of the selected shopping centres in Kraków. Material and methods. Air was sampled at the outlet of electrical hand dryers and surface swabs of hand dryers were taken in toilets of five shopping centres. Air sampling was conducted using the MAS-100 impactor. The number of mesophilic bacteria, fungi, actinomycetes, staphylococci and Escherichia coli was determined. The results of air analyses were compared with the limits provided by the Polish Standards on air quality. Results. The number of microorganisms varied between the studied centres. In terms of mesophilic bacteria and fungi the air was unpolluted. The concentration of actinomycetes however significantly exceeded the limits set by the Polish Standards. Numerous Escherichia coli were found both in the air and in swabs in one of the centres. However the number of E. coli and staphylococci did not exceed the minimum infective dose. Conclusions. The studies showed high concentrations of airborne actinomycetes and staphylococci. Also the presence of E. coli in the air and swabs allows the conclusion that legal regulations for concentrations of airborne microorganisms are necessary to make people aware of this problem. However, it was found that using electrical hand dryers does not have impact on human health.

Pressure pain sensitivity maps, self-reported musculoskeletal disorders and sickness absence among cleaners

DEFF Research Database (Denmark)

Binderup, Asbjørn Thalund; Holtermann, Andreas; Søgaard, Karen

2011-01-01

back regions (27 points). LTSA was defined as ten or more consecutive workdays with sick leave. RESULTS: The PPT maps revealed the spatial heterogeneity in mechanical sensitivity among cleaners. The level of pain in the neck and dominant shoulder and upper back within the last 7 days correlated......BACKGROUND: Pressure pain threshold mapping is a valuable method for the identification of distinct zones of mechanical pain sensitivity. Such approach was applied for the first time in relation to self-reported musculoskeletal disorders and long-term sickness absence (LTSA) within the last 12...... months among cleaners. METHODS: About 29 cleaners filled out a self-administered questionnaire regarding health, work-related measures and musculoskeletal disorders. Subsequently, PPTs were measured at (1) tibialis anterior (control location, 1 point), (2) the neck-shoulder (48 points) and (3) the low...

Breathing easier: Indonesia works towards cleaner air

International Nuclear Information System (INIS)

Madsen, Michael Amdi

2015-01-01

Indonesians can look forward to breathing cleaner air following upcoming changes in regulations introduced as a result of a study conducted using nuclear analytical techniques. Lead pollution and other fine particulate matter in the air is now, for the first time, being accurately monitored and is giving Indonesian officials a good understanding of their air pollution problem and how to manage it.

Substantiation of basic scheme of grain cleaning machine for preparation of agricultural crops seeds

Science.gov (United States)

Giyevskiy, A. M.; Orobinsky, V. I.; Tarasenko, A. P.; Chernyshov, A. V.; Kurilov, D. O.

2018-03-01

The article presents data on the feasibility of the concept of a high-efficiency seed cleaner with the consistent use of the air flow in aspiration and the multi-tier placement of the sorting grids in grating mills. As a result of modeling, the directions for further improvement of air-screen seed cleaning machines have been identified: an increase in the proportion of sorting grids in the mills up to 70 ... 80% and an increase in the speed of the air flow in the channel of the pre-filter cleaning up to 8.0 m / s. Experiments have established the competence of using mathematical modeling of airflow in the pneumatic system with the use of a finite-volume method for solving hydrodynamic equations for substantiating the basic parameters of the pneumatic system.

The determination of carbon dioxide concentration using atmospheric pressure ionization mass spectrometry/isotopic dilution and errors in concentration measurements caused by dryers.

Science.gov (United States)

DeLacy, Brendan G; Bandy, Alan R

2008-01-01

An atmospheric pressure ionization mass spectrometry/isotopically labeled standard (APIMS/ILS) method has been developed for the determination of carbon dioxide (CO(2)) concentration. Descriptions of the instrumental components, the ionization chemistry, and the statistics associated with the analytical method are provided. This method represents an alternative to the nondispersive infrared (NDIR) technique, which is currently used in the atmospheric community to determine atmospheric CO(2) concentrations. The APIMS/ILS and NDIR methods exhibit a decreased sensitivity for CO(2) in the presence of water vapor. Therefore, dryers such as a nafion dryer are used to remove water before detection. The APIMS/ILS method measures mixing ratios and demonstrates linearity and range in the presence or absence of a dryer. The NDIR technique, on the other hand, measures molar concentrations. The second half of this paper describes errors in molar concentration measurements that are caused by drying. An equation describing the errors was derived from the ideal gas law, the conservation of mass, and Dalton's Law. The purpose of this derivation was to quantify errors in the NDIR technique that are caused by drying. Laboratory experiments were conducted to verify the errors created solely by the dryer in CO(2) concentration measurements post-dryer. The laboratory experiments verified the theoretically predicted errors in the derived equations. There are numerous references in the literature that describe the use of a dryer in conjunction with the NDIR technique. However, these references do not address the errors that are caused by drying.

COMMERCIAL DEMONSTRATION OF THE MANUFACTURED AGGREGATE PROCESSING TECHNOLOGY UTILIZING SPRAY DRYER ASH

Energy Technology Data Exchange (ETDEWEB)

Roy Scandrol

2003-10-01

Universal Aggregates, LLC proposes to design, construct and operate a lightweight aggregate manufacturing plant at the Birchwood Power Facility in King George, Virginia. The installation and start-up expenses for the Birchwood Aggregate Facility are $19.5 million. The DOE share is $7.2 million (37%) and the Universal Aggregates share is $12.3 (63%). The project team consists of CONSOL Energy Inc., P.J. Dick, Inc., SynAggs, LLC, and Universal Aggregates, LLC. The Birchwood Facility will transform 115,000 tons per year of spray dryer by-products that are currently being disposed of in an offsite landfill into 167,000 tons of a useful product, lightweight aggregates that can be used to manufacture lightweight aggregates that can be used to manufacture lightweight and medium weight masonry blocks. In addition to the environmental benefits, the Birchwood Facility will create nine (9) manufacturing jobs plus additional employment in the local trucking industry to deliver the aggregate to customers or reagents to the facility. A successful demonstration would lead to additional lightweight aggregate manufacturing facilities in the United States. There are currently twenty-one (21) spray dryer facilities operating in the United States that produce an adequate amount of spray dryer by-product to economically justify the installation of a lightweight aggregate manufacturing facility. Industry sources believe that as additional scrubbing is required, dry FGD technologies will be the technology of choice. Letters from potential lightweight aggregate customers indicate that there is a market for the product once the commercialization barriers are eliminated by this demonstration project.

COMMERCIAL DEMONSTRATION OF THE MANUFACTURED AGGREGATE PROCESSING TECHNOLOGY UTILIZING SPRAY DRYER ASH

Energy Technology Data Exchange (ETDEWEB)

Roy Scandrol

2003-04-01

Universal Aggregates, LLC proposes to design, construct and operate a lightweight aggregate manufacturing plant at the Birchwood Power Facility in King George, Virginia. The installation and start-up expenses for the Birchwood Aggregate Facility are $19.5 million. The DOE share is $7.2 million (37%) and the Universal Aggregates share is $12.3 (63%). The project team consists of CONSOL Energy Inc., P.J. Dick, Inc., SynAggs, LLC, and Universal Aggregates, LLC. The Birchwood Facility will transform 115,000 tons per year of spray dryer by-products that are currently being disposed of in an offsite landfill into 167,000 tons of a useful product, lightweight aggregates that can be used to manufacture lightweight aggregates that can be used to manufacture lightweight and medium weight masonry blocks. In addition to the environmental benefits, the Birchwood Facility will create eight (8) manufacturing jobs plus additional employment in the local trucking industry to deliver the aggregate to customers or reagents to the facility. A successful demonstration would lead to additional lightweight aggregate manufacturing facilities in the United States. There are currently twenty-one (21) spray dryer facilities operating in the United States that produce an adequate amount of spray dryer by-product to economically justify the installation of a lightweight aggregate manufacturing facility. Industry sources believe that as additional scrubbing is required, dry flue gas desulfurization (FGD) technologies will be the technology of choice. Letters from potential lightweight aggregate customers indicate that there is a market for the product once the commercialization barriers are eliminated by this demonstration project.

Regenerating using aqueous cleaners with ozone and electrolysis

Science.gov (United States)

McGinness, Michael P.

1994-02-01

A new process converts organic oil and grease contaminates in used water based cleaners into synthetic surfactants. This permits the continued use of a cleaning solution long after it would have been dumped using previously known methods. Since the organic soils are converted from contaminates to cleaning compounds the need for frequent bath dumps is totally eliminated. When cleaning solutions used in aqueous cleaning systems are exhausted and ready for disposal, they will always contain the contaminates removed from the cleaned parts and drag-in from prior cleaning steps. Even when the cleaner is biodegradable these contaminants will frequently cause the waste cleaning solution to be a hazardous waste. Chlorinated solvents are rapidly being replaced by aqueous cleaners to avoid the new ozone-depletion product-labeling-law. Many industry standard halocarbon based solvents are being completely phased out of production, and their prices have nearly tripled. Waste disposal costs and cradle-to-grave liability are also major concerns for industry today. This new process reduces the amount of water and chemicals needed to maintain the cleaning process. The cost of waste disposal is eliminated because the water and cleaning compounds are reused. Energy savings result by eliminating the need for energy currently used to produce and deliver fresh water and chemicals as well as the energy used to treat and destroy the waste from the existing cleaning processes. This process also allows the cleaning bath to be maintained at the peak performance of a new bath resulting in decreased cycle times and decreased energy consumption needed to clean the parts. This results in a more efficient and cost effective cleaning process.

Evaluating the parameters of a mobile maize dryer in practice

Directory of Open Access Journals (Sweden)

Josef Los

2013-01-01

Full Text Available The method of drying maize for grain has been recently employed on a large scale in the Czech Republic not only thanks to new maize hybrids but also thanks to the existence of new models of drying plants. One of the new post-harvest lines is a plant in Lipoltice (mobile dryer installed in 2010, storage base in 2012 where basic operational measurements were made of the energy intensiveness of drying and operating parameters of the maize dryer were evaluated. The process of maize drying had two stages, i.e. pre-drying from the initial average grain humidity of 28.55% to 19.6% in the first stage, and the additional drying from 16.7% to a final storage grain humidity of 13.7%. Mean volumes of natural gas consumed per 1 t% for drying in the first and second stage amounted to 1.275 m3 and 1.56 m3, respectively. The total mean consumption of electric energy per 1 t% was calculated to be 1.372 kWh for the given configuration of the post-harvest line.

Impact of flow induced vibration acoustic loads on the design of the Laguna Verde Unit 2 steam dryer

International Nuclear Information System (INIS)

Forsyth, D. R.; Wellstein, L. F.; Theuret, R. C.; Han, Y.; Rajakumar, C.; Amador C, C.; Sosa F, W.

2015-09-01

Industry experience with Boiling Water Reactors (BWRs) has shown that increasing the steam flow through the main steam lines (MSLs) to implement an extended power up rate (EPU) may lead to amplified acoustic loads on the steam dryer, which may negatively affect the structural integrity of the component. The source of these acoustic loads has been found to be acoustic resonance of the side branches on the MSLs, specifically, coupling of the vortex shedding frequency and natural acoustic frequency of safety relief valves (SRVs). The resonance that results from this coupling can contribute significant acoustic energy into the MSL system, which may propagate upstream into the reactor pressure vessel steam dome and drive structural vibration of steam dryer components. This can lead to high-cycle fatigue issues. Lock-in between the vortex shedding frequency and SRV natural frequency, as well as the ability for acoustic energy to propagate into the MSL system, are a function of many things, including the plant operating conditions, geometry of the MSL/SRV junction, and placement of SRVs with respect to each other on the MSLs. Comision Federal de Electricidad and Westinghouse designed, fabricated, and installed acoustic side branches (ASBs) on the MSLs which effectively act in the system as an energy absorber, where the acoustic standing wave generated in the side-branch is absorbed and dissipated inside the ASB. These ASBs have been very successful in reducing the amount of acoustic energy which propagates into the steam dome. In addition, modifications to the Laguna Verde Nuclear Power Plant Unit 2 steam dryer have been completed to reduce the stress levels in critical locations in the dryer. The objective of this paper is to describe the acoustic side branch concept and the design iterative processes that were undertaken at Laguna Verde Unit 2 to achieve a steam dryer design that meets the guidelines of the American Society of Mechanical Engineers, Boiler and Pressure

Impact of flow induced vibration acoustic loads on the design of the Laguna Verde Unit 2 steam dryer

Energy Technology Data Exchange (ETDEWEB)

Forsyth, D. R.; Wellstein, L. F.; Theuret, R. C.; Han, Y.; Rajakumar, C. [Westinghouse Electric Company LLC, Cranberry Township, PA 16066 (United States); Amador C, C.; Sosa F, W., E-mail: forsytdr@westinghouse.com [Comision Federal de Electricidad, Central Nucleoelectrica Laguna Verde, Km 42.5 Carretera Cardel-Nautla, 91680 Alto Lucero, Veracruz (Mexico)

2015-09-15

Industry experience with Boiling Water Reactors (BWRs) has shown that increasing the steam flow through the main steam lines (MSLs) to implement an extended power up rate (EPU) may lead to amplified acoustic loads on the steam dryer, which may negatively affect the structural integrity of the component. The source of these acoustic loads has been found to be acoustic resonance of the side branches on the MSLs, specifically, coupling of the vortex shedding frequency and natural acoustic frequency of safety relief valves (SRVs). The resonance that results from this coupling can contribute significant acoustic energy into the MSL system, which may propagate upstream into the reactor pressure vessel steam dome and drive structural vibration of steam dryer components. This can lead to high-cycle fatigue issues. Lock-in between the vortex shedding frequency and SRV natural frequency, as well as the ability for acoustic energy to propagate into the MSL system, are a function of many things, including the plant operating conditions, geometry of the MSL/SRV junction, and placement of SRVs with respect to each other on the MSLs. Comision Federal de Electricidad and Westinghouse designed, fabricated, and installed acoustic side branches (ASBs) on the MSLs which effectively act in the system as an energy absorber, where the acoustic standing wave generated in the side-branch is absorbed and dissipated inside the ASB. These ASBs have been very successful in reducing the amount of acoustic energy which propagates into the steam dome. In addition, modifications to the Laguna Verde Nuclear Power Plant Unit 2 steam dryer have been completed to reduce the stress levels in critical locations in the dryer. The objective of this paper is to describe the acoustic side branch concept and the design iterative processes that were undertaken at Laguna Verde Unit 2 to achieve a steam dryer design that meets the guidelines of the American Society of Mechanical Engineers, Boiler and Pressure

Process analysis of biofuelled heat and power plants integrated with a flue gas dryer; Processtudie av biobraensleeldade kraftvaermeverk integrerade med roekgastork

Energy Technology Data Exchange (ETDEWEB)

Johansson, Kent; Steinwall, Pontus [Sycon Energikonsult AB, Malmoe (Sweden)

2000-01-01

In this report three different processes for combined heat and power production from biomass have been evaluated and compared. Both economical and technical questions have been investigated. The examined processes are: 1. CFB fuelled with wet biomass; 2. A boiler fuelled with pulverised biomass integrated with a traditional flue gas dryer; and 3. A boiler fuelled with pulverized biomass integrated with a flue gas dryer with a closed loop. All the processes have a district heat output of 80 MW. Calculations have been made at three different loads: 100, 70 and 40 % respectively. The performance characteristics in form of electric efficiency and fuel utilisation are very similar for the processes. To evaluate the thermodynamic differences between the processes, calculations have been made with extreme temperatures in the district heating net, 65 deg C/100 deg C. The process with a closed loop drier has a saturation temperature in the flue gas of 95 deg C. Therefore this process has a high fuel utilization even if the incoming water has a high temperature. The fuel utilization for alternatives 1 and 2 decreases almost down to the efficiency of the furnace. This shows that the temperature of the water is too high to recapture the latent heat in the flue gases. The investment costs for the processes have been estimated. Also these are very similar for the three alternatives. The cost for the process with the CFB is 412 million SEK. The boiler in alternative 2 and 3 is approximately 20 million SEK cheaper than the CFB. The decreased cost for the boiler is compensated by the cost for the dryers. The investment cost for the traditional dryer has been estimated to 20 million SEK and 30 million SEK for the closed loop dryer. The total cost for alternative 2 is then 417 million SEK and 414 million SEK for alternative 3. Operation and maintenance costs for the processes with dryer are supposed to be 1 respectively 1.5 million SEK higher than for alternative 1. The dryers may

A novel rate of the reaction between NaOH with CO2 at low temperature in spray dryer

Directory of Open Access Journals (Sweden)

Yadollah Tavan

2017-03-01

Full Text Available Carbon dioxide (CO2 is an influential greenhouse gas that has a significant impact on global warming partly. Nowadays, many techniques are available to control and remove CO2 in different chemical processes. Since the spray dryer has high removal efficiency rate, a laboratory-scale spray dryer is used to absorb carbon dioxide from air in aqueous solution of NaOH. In the present study, the impact of NaOH concentration, operating temperature and nozzle diameter on removal efficiency of CO2 is explored through experimental study. Moreover, the reaction kinetic of NaOH with CO2 is studied over the temperature range of 50–100 °C in a laboratory-scale spray dryer absorber. In the present contribution, a simple reaction rate equation is proposed that shows the lowest deviation from the experimental data with error less than 2%.

ANALISIS KELAYAKAN TEKNIS DAN FINANSIAL DARI INVESTASI PENGADAAN TRAY DRYER BERBAHAN BAKAR BIOMASSA PADA USAHA ARANG TEMPURUNG KELAPA BERBASIS EKSPOR (Studi Kasus di Tropica Nucifera Industry – Yogyakarta

Directory of Open Access Journals (Sweden)

Fanny Widadie

2013-11-01

Full Text Available The purpose of the study is to assess the technical and financial feasibility of procurement investment Tray Dryer fueled biomass to operations of coconut shell charcoal briquette in PT. Tropica Nucifera Industry. The result showed that investment-Tray Dryer on cocnut shell charcoal briquette bussiness was highly feasibile both the technical and financial aspects. The technical aspect was seen that the quantity-production capabilities of coconut shell charcoal briquettes using a dryer-Tray Dryer could be increased 15 percent compared the previous consdition-used of solar energy. While the quality of the charcoal briquettes produced from Tray Dryer was a much butter quality, moisture content (6.39%; ash (2.65%; carbon-bound (85.83%, compared to using sunlight, water content (15.89; ash (2.57% and carbon-bound (77.32%.The financial aspects of procurement Tray Dryer investment that its value was more feasible than previous, nothing Tray Dryer. Coconut shell charcoal briquet enterprises without using Tray Dryer was feasible to be done with NPV 1,058,928.12, IRR 63%, Payback Period 1 year and 9 moths, Net B/C 2.25 and analysis of swicthcing value reached 20 percent. And after the business using Tray Drayer, the financial analysis was much more feasible with NPV 2,285,500,498.12, IRR 113%, Payback Period 11 months, Net B/C 3.5 and analysis of switching value reached 50 percent.

Increased participation among cleaners as a strategy to improve quality and occupational health

OpenAIRE

Öhrling, Therese

2014-01-01

Like many other industries, today the cleaning industry is affected more than ever by competition and pressure toward low prices, which leads to a nonadvantageous situation for cleaners. These days many Swedish municipalities choose to outsource cleaning service in order to save money, although the situation for the cleaners appears to be worsening. The aim of this paper is to evaluate an alternative organizational structure within a Swedish public cleaning division to investigate how good wo...

Experimental investigation and thermodynamic performance analysis of a solar dryer using an evacuated-tube air collector

International Nuclear Information System (INIS)

Lamnatou, Chr.; Papanicolaou, E.; Belessiotis, V.; Kyriakis, N.

2012-01-01

Highlights: ► We evaluate an evacuated-tube solar air collector and use it to develop a novel dryer. ► Apple, carrot and apricot thin-layer drying experiments are conducted. ► Best overall fitting among several available thin-layer drying models is pursued. ► Thermodynamic analysis yields optimal collector area, energy utilization/exergy loss. ► The proposed dryer has a capacity for drying larger quantities of products. -- Abstract: The present work presents a thermodynamic performance analysis of a solar dryer with an evacuated-tube collector. Drying experiments for apples, carrots and apricots were conducted, after a preliminary stage of the investigation which included measurements for the determination of the collector efficiency. These results showed that the warm outlet air of the collector attains temperature levels suitable for drying of agricultural products without the need of preheating. Thus, the present collector was used as the heat source for a drying chamber in the frame of the development of a novel, convective, indirect solar dryer; given the fact that in the literature there are only a few studies about this type of collectors in conjunction with solar drying applications. Thin-layer drying models were fitted to the experimental drying curves, including the recent model of Diamante et al. which showed good correlation coefficients for all the tested products. Drying parameters such as moisture ratio and drying rates were calculated. Furthermore, an energetic/exergetic analysis of the dryer was also conducted and performance coefficients such as pick-up and exergy efficiencies, energy utilization ratio, exergy losses were determined for several configurations such as single and double-trays and several drying air velocities. On the other hand, an optimal collector surface area study was conducted, based on laws for minimum entropy generation. Design parameters such as optimum collector area were determined based on the minimum entropy

Cleaner Technologies and the Stability of International Environmental Agreements

NARCIS (Netherlands)

Benchekroun, H.; Ray Chaudhuri, A.

2012-01-01

Abstract: This paper shows that, if countries are farsighted when deciding whether to defect from a coalition, then the implementation of cleaner technologies may jeopardize the chances of reaching an international environmental agreement. The grand coalition may be destabilized by the

Experimental study of regenerative desiccant integrated solar dryer with and without reflective mirror

Energy Technology Data Exchange (ETDEWEB)

Shanmugam, V. [Department of Mechanical Engineering, Sathyabama University, Chennai, 600 119 (India); Natarajan, E. [Institute for Energy Studies, College of Engineering, Anna University, Chennai, 600 025 (India)

2007-06-15

An indirect forced convection with desiccant integrated solar dryer has been built and tested. The main parts are: a flat plate solar air collector, a drying chamber, desiccant bed and a centrifugal blower. The system is operated in two modes, sunshine hours and off sunshine hours. During sun shine hours the hot air from the flat plate collector is forced to the drying chamber for drying the product and simultaneously the desiccant bed receives solar radiation directly and through the reflected mirror. In the off sunshine hours, the dryer is operated by circulating the air inside the drying chamber through the desiccant bed by a reversible fan. The dryer is used to dry 20 kg of green peas and pineapple slices. Drying experiments were conducted with and without the integration of desiccant unit. The effect of reflective mirror on the drying potential of desiccant unit was also investigated. With the inclusion of reflective mirror, the drying potential of the desiccant material is increased by 20% and the drying time is reduced. The drying efficiency of the system varies between 43% and 55% and the pick-up efficiency varies between 20% and 60%, respectively. Approximately in all the drying experiments 60% of moisture is removed by air heated using solar energy and the remainder by the desiccant. The inclusion of reflective mirror on the desiccant bed makes faster regeneration of the desiccant material. (author)

PADDY DRYING IN MIXED ADSORPTION DRYER WITH ZEOLITE: DRYING RATE AND TIME ESTIMATION

Directory of Open Access Journals (Sweden)

Mochammad Djaeni

2013-11-01

Full Text Available Recently, the main problem of the rice stock and distribution in Indonesia is the quality degradation as indicated in unpleasant odor (smelly, stained, yellowness, and high percentage of broken rice. This is due to the low of paddy quality dried by from either direct sunlight or conventional fluidized bed dryer. As a result, the paddy cracks and breaks easily during milling in which causes the storage life being shorter as the enzymatic degradation by germ or fungi occurs. Air dehumidified with zeolite at drying medium temperature is potential to improve the quality of paddy. Zeolite is a material having high affinity to water vapor. In this case, the paddy and zeolite was mixed and fluidized with the air. The air will evaporate water from paddy, and at same time, the zeolite will adsorb water from air. Hence, the humidity of dryer can be kept low in which improves the driving force for drying. This work discusses the effect of presence of zeolite in the dryer, operational drying temperature, air velocity and relative humidity on drying rate of paddy. The results showed that increasing of zeolite as well as operational temperature increased the drying rate. In addition, using the model, the air dehumidification with zeolite and increase of air velocity can speed up drying time significantly at operational temperature below 80oC. This condition is very suitable for paddy drying since the quality degradation can be avoided.

Screening for common mental disorders and substance abuse among temporary hired cleaners in Egyptian Governmental Hospitals, Zagazig City, Sharqia Governorate.

Science.gov (United States)

Abbas, R A; Hammam, R A M; El-Gohary, S S; Sabik, L M E; Hunter, M S

2013-01-01

Informal employment is common in developing countries, including Egypt. This type of employment may have significant consequences on mental health. To determine the prevalence and risk factors of common mental disorders and substance abuse among temporary hired hospital cleaners. A cross-sectional study was conducted on 242 adult temporary cleaners and 209 permanent cleaners working in 4 governmental hospitals in Zagazig City, Sharqia Governorate, Egypt. All participants were invited to complete a structured questionnaire through a semi-structured interview which included the self-reporting questionnaire 20 items (SRQ-20) and the work stress scale. Assessment of drug use included urine-based screening tests for common substances abused. The prevalence of job stress, common mental disorders and substance abuse, particularly tramadol and cannabis (Bango), was significantly higher in the studied temporary cleaners compared to permanent cleaners. Risk factors associated with increased susceptibility of the temporary cleaners to common mental disorders were family history of substance abuse, high crowding index, history of physical illness, low educational level, and smoking; while being unmarried, male sex, family history of mental disorder, age ≥40 years, smoking, and length of service ≥8 years, were associated with substance abuse among the same group. Temporary hired hospital cleaners suffered from impaired mental health more than permanent cleaners. Therefore, expanding the coverage of current laws and occupational safety and health standards to cover workers in the informal sector especially in developing countries is recommended.

Screening for Common Mental Disorders and Substance Abuse among Temporary Hired Cleaners in Egyptian Governmental Hospitals, Zagazig City, Sharqia Governorate

Directory of Open Access Journals (Sweden)

RA Abbas

2012-12-01

Full Text Available Background: Informal employment is common in developing countries, including Egypt. This type of employment may have significant consequences on mental health. Objectives: To determine the prevalence and risk factors of common mental disorders and substance abuse among temporary hired hospital cleaners. Methods: A cross-sectional study was conducted on 242 adult temporary cleaners and 209 permanent cleaners working in 4 governmental hospitals in Zagazig City, Sharqia Governorate, Egypt. All participants were invited to complete a structured questionnaire through a semi-structured interview which included the self-reporting questionnaire 20 items (SRQ-20 and the work stress scale. Assessment of drug use included urine-based screening tests for common substances abused. Results: The prevalence of job stress, common mental disorders and substance abuse, particularly tramadol and cannabis (Bango, was significantly higher in the studied temporary cleaners compared to permanent cleaners. Risk factors associated with increased susceptibility of the temporary cleaners to common mental disorders were family history of substance abuse, high crowding index, history of physical illness, low educational level, and smoking; while being unmarried, male sex, family history of mental disorder, age ≥40 years, smoking, and length of service ≥8 years, were associated with substance abuse among the same group. Conclusion: Temporary hired hospital cleaners suffered from impaired mental health more than permanent cleaners. Therefore, expanding the coverage of current laws and occupational safety and health standards to cover workers in the informal sector especially in developing countries is recommended.

Saving energy. [Metal Coating With Infrared Dryers

Energy Technology Data Exchange (ETDEWEB)

Schmid, K

1981-01-01

One way of saving energy in metal coating is by using electrically heated infrared dryers with medium-wave radiation (2 to 3 ..mu..m). The absorbing capacity of varnishes and plastic coatings is >90% in this range so that the radiation energy is almost completely transformed into heat. Medium-wave radiation sources have a much higher service life than short-wave sources (30.000 hours of operation) and do not require cooling; compared with long-wave sources, they have a higher heat transfer and thus much shorter drying times. The main fields of application, a cost example, and practical examples among the customers of Messrs. Eisenmann are presented.

Design and Performance Evaluation of a Solar Assisted Heat Pump Dryer Integrated with Biomass Furnace for Red Chilli

Directory of Open Access Journals (Sweden)

M. Yahya

2016-01-01

Full Text Available The performance of a solar assisted heat pump dryer integrated with biomass furnace has been designed and evaluated for drying red chillies, and drying kinetics of red chillies were evaluated. The red chillies were dried from 22 kg with moisture content of 4.26 db to moisture content of 0.08 db which needed 11 hours, with the average drying chamber temperature, drying chamber relative humidity, and an air mass flow rate of 70.5°C, 10.1%, and 0.124 kg/s, respectively, while the open sun drying needed 62 hours. Compared to open sun drying, this dryer yielded 82% saving in drying time. The drying rate, the specific moisture extraction rate, and thermal efficiency of the dryer were estimated in average to be about 1.57 kg/h, 0.14 kg/kWh, and 9.03%, respectively. Three mathematical models, the Newton, Henderson-Pabis, and Page models, were fitted to the experimental data on red chillies dried by solar assisted heat pump dryer integrated with biomass furnace and open sun drying. The performance of these models was evaluated by comparing the coefficient of determination (R2, mean bias error (MBE, and root mean-square error (RMSE. The Page model gave the best results for representing drying kinetics of red chillies.

Modelling of hot air chamber designs of a continuous flow grain dryer

DEFF Research Database (Denmark)

Kjær, Lotte Strange; Poulsen, Mathias; Sørensen, Kim

2018-01-01

The pressure loss, flow distribution and temperature distribution of a number of designs of the hot air chamber in a continuous flow grain dryer, were investigated using CFD. The flow in the dryer was considered as steady state, compressible and turbulent. It is essential that the grain...... is uniformly dried as uneven drying can result in damage to the end-product during storage. The original commercial design was modified with new guide vanes at the inlets to reduce the pressure loss and to ensure a uniform flow to the line burner in the hot air chamber. The new guide vane design resulted...... in a 10% reduction in pressure loss and a γ-value of 0.804. Various design changes of the hot air chamber were analysed in terms of pressure loss and temperature distribution with the aim of a temperature variation of 5 K at the outlet ducts. An obstruction design was analysed, which improved mixing...

Design aspects of integrated compact thermal storage system for solar dryer applications

International Nuclear Information System (INIS)

Rajaraman, R.; Velraj, R.; Renganarayanan, S.

2000-01-01

Solar energy is an excellent source for drying of crops, fruits, vegetables and other agricultural and forest products. Though the availability of solar energy is plenty, it is time dependent in nature. The energy need for some applications is also time dependent, but in a different pattern and phase from the solar energy supply. This implies that the solar dryer should be integrated with an efficient thermal storage system to match the time-dependent supply and end-use requirements. Based on the studies carried out on Latent Heat Thermal Storage (LHTS) Systems, it is observed that when air is used as the heat transfer fluid in LHTS system, nearly uniform surface heat flux can be achieved. Hence the LHTS systems are most suitable for air based solar drying applications. In the present work some major conclusions arrived from the investigations on LHTS systems and the design considerations for the integrated latent heat thermal storage for the solar dryer are reported. (Author)

Ethnic Mobilization among Korean Dry Cleaners

OpenAIRE

Thomas, Ward F; Ong, Paul

2015-01-01

Korean immigrants in the U.S. rely heavily on ethnic resources to start small businesses.  Ethnic resources include business networks and knowledge, start-up capital, and access to labor power that are embedded in networks of family, friends, and co-ethnics.  This paper shows how Korean dry cleaners in Southern California used ethnic resources to mobilize in response to an environmental policy initiated by the South Coast Air Quality Management District (AQMD).  While Korean immigrants used e...

Actual problems of municipal cleaner’s waste waters

Directory of Open Access Journals (Sweden)

Konko¾ová Patrícia

2000-03-01

Full Text Available In paper are evaluated social and economical changes in water economy with emphasis on complex evaluation of municipal cleaner’s waste waters with respect of legislative, position of ownerskip relationskips and financial security of public experiences of water economy.

Third quarterly report and final report within the counterpart subcontract no. 97/219: Support to the National Cleaner Production Centre, Tanzania

DEFF Research Database (Denmark)

Jørgensen, Michael Søgaard

1999-01-01

The report analyses barriers and incentivres to cleaner production in Tanznaia based on experiences in three demonstration projects with around 25 companies.An outline for a policy study on cleaner production in Tanzania and for the strengthening of cleaner production in Tanzania is given....

The association between health and sickness absence among Danish and non-Western immigrant cleaners in Denmark

DEFF Research Database (Denmark)

Carneiro, Isabella G.; Rasmussen, Charlotte D. N.; Jørgensen, Marie B.

2013-01-01

PURPOSE: The aim of the study is to investigate the association between health and sickness absence among Danish and non-Western immigrant cleaners in Denmark. METHODS: This study is based on a cross-sectional analysis of baseline data from 2007 to 2008. The study population includes 276 cleaners...

Physical Fitness of Cleaners in Faculty of Medicine Universitas Padjadjaran, November 2012

Directory of Open Access Journals (Sweden)

Adi Wibisono Sulistijo

2015-09-01

Full Text Available Background: Cleaning is an occupation that is carried out worldwide in many different environments. Cleaning workers (cleaners often have low occupational skills and belong to the less advantaged educational and socioeconomic groups. Because of the high physical work demands and low cardiorespiratory fitness, cleaners have the risk to have cardiovascular diseases. The aim of this study was to measure the 5 components of physical fitness (cardiorespiratory endurance, muscle endurance, muscle strength, flexibility and body composition of cleaners in Faculty of Medicine Universitas Padjadjaran. Methods: A descriptive study was carried out to all cleaners (31 persons of Faculty of Medicine Universitas Padjadjaran in November 2012. The subjects were tested for cardiorespiratory endurance, muscle endurance, muscle strength, flexibility and body composition. The results were categorized using the standard of Ministry of Health Republic Indonesia. Results: From 31 subjects, cardiorespiratory endurance was in poor category (50%. Shoulder and hand muscle endurance was in poor category (54.8% and stomach muscle endurance was in very poor category (67.7%. Hand−grip muscular strength was in very poor category: right hand (80.7% and left hand (87.1%. Back muscle strength was in poor category (58.1%. Leg muscular strength was in very poor category (48.4%. Flexibility was in a very good category (97% and body composition was also in a good category (54.8%. Conclusions: From 5 components of cleaners’ physical fitness, 3 components (cardiorespiratory endurance, muscle endurance and muscular strength are in poor and very poor category.

Primary DNA Damage in Dry Cleaners with Perchlorethylene Exposure

Directory of Open Access Journals (Sweden)

Mohammad Azimi

2017-10-01

Full Text Available Background: Perchloroethylene is a halogenated solvent widely used in dry cleaning. International agency of research on cancer classified this chemical as a probable human carcinogen. Objective: To evaluate the extent of primary DNA damage in dry cleaner workers who were exposed to perchloroethylene as compared to non-exposed subjects. The effect of exposure modifying factors such as use of personal protective equipment, perceived risk, and reported safe behaviors on observed DNA damage were also studied. Methods: 59 exposed and non-exposed workers were selected from Yazd, Iran. All the 33 exposed workers had work history at least 3 months in the dry cleaning shops. Peripheral blood sampling was performed. Microscope examination was performed under fluorescent microscope (400×. Open comet software was used for image analysis. All biological analysis was performed in one laboratory. Results: Primary DNA damage to leukocytes in dry cleaners was relatively high. The median tail length, %DNA in tail, and tail moment in exposed group were significantly higher than those in non-exposed group. There was no significant difference between smokers and nonsmokers in terms of tail length, tail moment, and %DNA in tail. There was no significant correlation between duration of employment in dry cleaning and observed DNA damage in terms of tail length, tail moment and %DNA in tail. Stratified analysis based on exposed and nonexposed category showed no significant relationship between age and observed DNA damage. Conclusion: Occupationally exposure to perchloroethylene can cause early DNA damage in dry cleaners.

Drying of Rosella (Hibiscus sabdariffa Flower Petals using Solar Dryer with Double Glass Cover Collector

Directory of Open Access Journals (Sweden)

Tjukup Marnoto

2014-10-01

Full Text Available Chemical ingredients in rosella petals are very beneficial for health. Rosella petals needed to be drained for storage and packing purpose. The traditional drying takes 5 days and less healthy. Solar dryer technology can speed up the drying process and protect materials from dust contamination. Solar dryer with double glass covered collector has been designed and made for drying of agricultural products such as rosella flowers. Rosella petals as much as 2300 grams with initial moisture content of 90.84 % be dried with this dryer until the moisture content of 7.67 % takes only 2 days, although the weather was less sunny . The temperature in the drying chamber was not more than 50° C, so it was good for drying groceries, not damaging chemical ingredients. The relative humidity in the space dryeris was about 40 % and it was still relative low. Drying rate and drying performance was expressed by the efficiency and Specific Moisture Evaporation Rate ( SMER were influenced by water content of the dried material and weather. Daily efficiency at the first and the second day: 14.931 % and 5.78%, while the daily SMER on the first and the second day: 0.222 and 0.0256 ( kg / kWh .

Final Report: Laboratory Development of a High Capacity Gas-Fired Paper Dryer

Energy Technology Data Exchange (ETDEWEB)

Yaroslav Chudnovsky; Aleksandr Kozlov; Lester Sherrow

2005-09-30

Paper drying is the most energy-intensive and temperature-critical aspect of papermaking. It is estimated that about 67% of the total energy required in papermaking is used to dry paper. The conventional drying method uses a series of steam-heated metal cylinders that are required to meet ASME codes for pressure vessels, which limits the steam pressure to about 160 psig. Consequently, the shell temperature and the drying capacity are also limited. Gas Technology Institute together with Boise Paper Solutions, Groupe Laperrier and Verreault (GL&V) USA Inc., Flynn Burner Corporation and with funding support from the U.S. Department of Energy, U.S. natural gas industry, and Gas Research Institute is developing a high efficiency gas-fired paper dryer based on a combination of a ribbon burner and advanced heat transfer enhancement technique. The Gas-Fired Paper Dryer (GFPD) is a high-efficiency alternative to conventional steam-heated drying drums that typically operate at surface temperatures in the 300 deg F range. The new approach was evaluated in laboratory and pilot-scale testing at the Western Michigan University Paper Pilot Plant. Drum surface temperatures of more than 400 deg F were reached with linerboard (basis weight 126 lb/3000 ft2) production and resulted in a 4-5 times increase in drying rate over a conventional steam-heated drying drum. Successful GFPD development and commercialization will provide large energy savings to the paper industry and increase paper production rates from dryer-limited (space- or steam-limited) paper machines by an estimated 10 to 20%, resulting in significant capital costs savings for both retrofits and new capacity.

76 FR 22453 - Energy Conservation Program: Energy Conservation Standards for Residential Clothes Dryers and...

Science.gov (United States)

2011-04-21

... Mode and Off Mode b. Automatic Cycle Termination c. Ventless Clothes Dryers d. Consumer Usage Habits e... as cooling capacity in British thermal units (Btu) per hour (h) divided by electrical input power in...

Implementing Cleaner Production as an Environmental Management Efforts in Small Industries of Cassava Chips

Directory of Open Access Journals (Sweden)

Rahmadyanti Erina

2016-01-01

Full Text Available Small and Medium Enterprises (SMEs is one of the major driving factors for Indonesian economy, especially in food processing industries. The cassava-based industry is one type of food and beverage industry with chips as its major product. The limitations of knowledge caused their activities to only aim at pursuing economic benefits and ignoring the environmental balance. The most appropriate preventive method used, according to the characteristics of SMEs in Indonesia, is Cleaner Production. This study aims to reduce the risk of environmental pollution caused by the waste production of small chips industries by implementing cleaner production. The method used in this study is quick scanning by analyzing mass balance, energy, and utilities that aim to find an inefficient process to minimize losses. Implementation of cleaner production may include good housekeeping, reducing, and reusing. Based on the assessment of alternative eligibility criteria, the equipment modifications are the main factor in implementing cleaner production that drives the profits by providing efficiency of cutting as much as 80 percent and optimizes the profits into 57.62 kg in a month or 691.44 kg in a year. If the price of cassava chips is IDR 40,000 in a kg, then it would save IDR 27,657,600 in a year.

Cleaner production for solid waste management in leather industry ...

African Journals Online (AJOL)

Cleaner production for solid waste management in leather industry. ... From the processes, wastes are generated which include wastewater effluents, solid wastes, and hazardous wastes. In developing countries including Ethiopia, many ... The solid waste inventory of the factory has been carried out. The major problems ...

GAS-PHASE AND PARTICULATE EMISSIONS DURING APPLICATION OF A WATER-BASED CLEANER WITH A HAND-PUMP SPRAYER

Science.gov (United States)

The paper gives results of tests in a controlled environment test room to measure concentrations of 2-butoxyethanol and particles during application of a cleaner to realistic surfaces (counter tops, glass, walls). (NOTE: Users of water-based cleaners applied with hand-pump spray...

Back to Office Report. Mission no.1 to Tanzania as counterpart institution to Cleaner Production Centre of Tanzania

DEFF Research Database (Denmark)

Jørgensen, Michael Søgaard

1996-01-01

A presentation of some important actors and institutions in the capacity building within cleaner production in Tanzania......A presentation of some important actors and institutions in the capacity building within cleaner production in Tanzania...

Effects on musculoskeletal pain, work ability and sickness absence in a 1-year randomised controlled trial among cleaners

DEFF Research Database (Denmark)

Jørgensen, Marie B.; Faber, Anne; Hansen, Jørgen V.

2011-01-01

Only a few workplace initiatives among cleaners have been reported, even though they constitute a job group in great need of health promotion. The purpose of this trial was to evaluate the effect of either physical coordination training or cognitive behavioural training on musculoskeletal pain......, work ability and sickness absence among cleaners. A cluster-randomised controlled trial was conducted among 294 female cleaners allocated to either physical coordination training (PCT), cognitive behavioural training (CBTr) or a reference group (REF). Questionnaires about musculoskeletal pain and work...... intervention appeared effective for reducing chronic neck/shoulder pain among the female cleaners. It is recommended that future interventions among similar high-risk job groups focus on the implementation aspects of the interventions to maximise outcomes more distal from the intervention such as work ability...

Successes emerge in search for cleaner processes

International Nuclear Information System (INIS)

Anon.

1992-01-01

Faced with mounting public and regulatory pressures, many chemical producers have long adopted pollution reduction efforts. But increasingly, firms are eyeing fundamental process changes to achieve cleaner technologies. In addition to environmental benefits, the promised economic payoffs are clear: higher yields and an escape from soaring waste treatment and disposal costs. Having such technologies, says Paolo Galli, Montecatini's (Milan) director/corporate research, is a tremendous tool. It's becoming an increasingly important competitive element. Indeed, suggests David Hyde, ICI's (London) manager/environmental technology, everyone is looking to use cleaner technologies for a competitive advantage. A number of leading technology groups, including UOP (Des Plaines, IL), are working on replacing hydrofluoric acid (HF) with solid catalysts in alkylation processes. Although it is technologically tough to replace HF or alternative sulfuric acid technology, the rewards could be huge in producing high-octane fuel additives. Catalytica (Mountain View, CA), for one, is building a pilot plant with partners Neste (Helsinki) and Du Pont's Conoco. The company has developed a process to manufacture high-purity DMC by direct synthesis from carbom monoxide, methanol, and oxygen. The medium-pressure process uses a copper salts catalyst system; EniChem says the only significant by-product is carbon dioxide, and there are no chlorinated impurities

Evaluation of an industrial gas-fired IR dryer; Utvaerdering av en industriell gaseldad IR-straalare

Energy Technology Data Exchange (ETDEWEB)

Stenstroem, S; Hermodsson, S

1994-11-01

The IR dryer is used in a paper making machine to dry the paper web after it has been coated with a surface layer. In part 1 of the project a mathematical model have been developed, capable of calculating the radiation intensity and other energy flows in the dryer. In part 2 of the project, measurements have been made on the IR radiator mounted in the paper making machine. The calculation model shows the efficiency of the radiator to 39% at full power and 35% at half power. The direct measurements were made at half power and gave an efficiency of 31% for new radiators and 28% for old ones. The conclusion is that the calculation model values corresponds very well compared with direct measurements.

Blood cleaner on-chip design for artificial human kidney manipulation

Directory of Open Access Journals (Sweden)

Suwanpayak N

2011-05-01

Full Text Available N Suwanpayak1, MA Jalil2, MS Aziz3, FD Ismail3, J Ali3, PP Yupapin11Nanoscale Science and Engineering Research Alliance (N'SERA, Advanced Research Center for Photonics, Faculty of Science, King Mongkut's Institute of Technology, Ladkrabang, Bangkok, Thailand; 2Ibnu Sina Institute of Fundamental Science Studies (IIS, 3Institute of Advanced Photonics Science, Nanotechnology Research Alliance, Universiti Teknologi Malaysia, Johor Bahru, MalaysiaAbstract: A novel design of a blood cleaner on-chip using an optical waveguide known as a PANDA ring resonator is proposed. By controlling some suitable parameters, the optical vortices (gradient optical fields/wells can be generated and used to form the trapping tools in the same way as optical tweezers. In operation, the trapping force is formed by the combination between the gradient field and scattering photons by using the intense optical vortices generated within the PANDA ring resonator. This can be used for blood waste trapping and moves dynamically within the blood cleaner on-chip system (artificial kidney, and is performed within the wavelength routers. Finally, the blood quality test is exploited by the external probe before sending to the destination. The advantage of the proposed kidney on-chip system is that the unwanted substances can be trapped and filtered from the artificial kidney, which can be available for blood cleaning applications.Keywords: optical trapping, blood dialysis, blood cleaner, human kidney manipulation

Numerical calculations of heat engineering parameters of a solar greenhouse dryer

International Nuclear Information System (INIS)

Akhatov, Zh.S.; Khalimov, A.S.

2015-01-01

The results of numerical simulation to determine the optimum volume of a thermal storage water heater in a solar greenhouse dryer are presented. A CAD (computer-aided design) model is created for the given installation by simulating the heat transfer processes with the aid of the Solid Works Flow Simulation software. The given CAD model consists of a concrete foundation and a steel frame in which translucent coatings made from two-layer polycarbonate sheets 6 mm in thickness with an air gap between the two layers are attached. The north wall is made of bricks with size and thickness of 2 x 4 m"2 and 0.4 m, respectively. The front surface has an angle of inclination 39.53 degree with respect to the horizontal surface for the maximum incidence of solar radiation to its surface. All the geometrical dimensions of the solar greenhouse dryer were selected on the basis of the allocated platform for the solar drying installation 3 x 4 m"2 in size. It is shown that the optimum volume of the heat storage tank for the present installation is 500 L. (authors)

Effect of brining on the drying rate of tilapia in a solar tunnel dryer

Energy Technology Data Exchange (ETDEWEB)

Kituu, G.M.; Shitanda, D.; Kanali, C.L.; Mailutha, J.T. [Jomo Kenyatta Univ. of Agriculture and Technology, Nairobi (Kenya). BEED

2008-07-01

In addition to being a source of protein, fish is an important source of local and foreign currency earnings in Kenya. A substantial amount of fish production is exported. Approximately 30 per cent is exported to the European Union, the United States, and countries in the Middle East, but nearly half of the total annual fish harvest in Kenya goes to waste due to poor processing and preservation. Measures must be taken to ensure the fish industry is protected and waste is minimized, since the livelihood of over 500,000 people depends on fish as a source of proteins and employment. Therefore, it is necessary to implement appropriate and affordable processing and preservation techniques for fish at the artisanal landing sites in order to reduce the wastage and spoilage of fish during oversupply, and to enhance long storage. This paper presented studies that were conducted to determine the effect of brining on the drying rate of tilapia in a solar tunnel dryer. The paper discussed the materials and methods, including a description of the solar tunnel dryer system; the brining process of fish; the fish drying process; and data analysis. It was concluded that limiting the amount of salt used in brining, and subsequently dehydrating fish with a solar tunnel dryer achieves a more stable and suitable dried fish product than osmotic dehydration or solar drying process separately. 19 refs., 5 figs., 2 appendices.

Evaluation of ozone generation and indoor organic compounds removal by air cleaners based on chamber tests

Science.gov (United States)

Yu, Kuo-Pin; Lee, Grace Whei-May; Hsieh, Ching-Pei; Lin, Chi-Chi

2011-01-01

Ozone can cause many health problems, including exacerbation of asthma, throat irritation, cough, chest ache, shortness of breath, and respiratory infections. Air cleaners are one of the sources of indoor ozone, and thus the evaluation of ozone generated by air cleaners is desired significant issue. Most evaluation methods proposed are based on chamber tests. However, the adsorption and desorption of ozone on the wall of test chamber and the deposition of ozone resulted from the surface reaction can influence the evaluation results. In this study, we developed a mass balance model that took the adsorption, desorption and deposition of ozone into consideration to evaluate the effective ozone emission rates of six selected air cleaners. The experiments were conducted in a stainless steel chamber with a volume of 11.3 m 3 at 25 °C and 60% relative humidity. The adsorption, desorption and deposition rate constants of ozone obtained by fitting the model to the experimental data were k a = 0.149 ± 0.052 m h -1, k d = 0.013 ± 0.007 h -1, and k r = 0.050 ± 0.020 h -1, respectively. The effective ozone emission rates of Air Cleaners No. 1, 2, and 3 ranged between 13,400-24,500 μg h -1, 7190-10,400 μg h -1, and 4880-6560 μg h -1, respectively, which were more stable than those of No.4, 5, and 6. The effective ozone emission rates of Air Cleaners No. 4, 5, and 6 increased with the time of operation which might be relevant to the decrease of ozone removal by the "aging" filter installed in these cleaners. The removal of toluene and formaldehyde by these six air cleaners were also evaluated and the clean air delivery rates (CADRs) of these two pollutants ranged from non-detectable to 0.42 ± 0.08 m 3 h -1, and from non-detectable to 0.75 ± 0.07 m 3 h -1, respectively. The CADRs showed an insignificant relationship with the effective ozone emission rates. Thus, the removal of toluene and formaldehyde might be resulted from the adsorption on the filters and the

Analysis and Testing of a Natural Convection Solar Dryer for the Tropics

Directory of Open Access Journals (Sweden)

A. O. Adelaja

2013-01-01

Full Text Available Solar dryers are imperative for the tropical and sub-Saharan African countries, which are faced with the duo challenges of inadequate electrical energy supply, which has severely limited the application of conventional refrigeration as a means of preservation of agricultural produce, and the need to make produce competitive in the international market. In this study, a cost-effective natural convection solar dryer was developed; the thermal and drying analyses were done and tested to obtain some performance evaluation parameters for the system in order to examine its efficiency and effectiveness by drying some plantain fillets. The collector and system efficiencies are found to be 46.4% and 78.73%, respectively, while a percentage moisture removal of 77.5% was achieved at the 20th hour in order to give final moisture contents of 15.75% in the product, which still maintained its integrity. With a cost of about $195.00, it has been affordable for the small- and medium-scale enterprises as well as for private use in domestic applications.

Sustainability and cleaner production: a study on the implications competitive advantage in business

Directory of Open Access Journals (Sweden)

Jaqueline Guimarães Santos

2015-08-01

Full Text Available This paper discusses the relationship between the adoption of environmental management system in the business and the competitive advantages that can result from this process. Therefore, the effects are discussed the emergence of a model of sustainable development and the role and opportunities of the company that perspective. Being theoretical, the aim of this paper is to discuss the potential contributions that the implementation of cleaner production technology can offer to the enterprise competitive strategy. To elucidate these relationships are discussed concepts relating to the introduction of an environmental management system, which emphasized the use of environmental measures, specifically the inherent Cleaner Production that aim to reduce the environmental impacts of industrial production, eliminating waste and reducing costs. Moreover, the concept of competitive advantage is crafted light of assumptions Porter on profitability from cost reduction and product differentiation. The findings indicate that the introduction of the Cleaner Production to reduce costs and add value to the image of the product, is an instrument of competitiveness that allows the company to differentiate and gain competitive advantage.

Screening for Common Mental Disorders and Substance Abuse among Temporary Hired Cleaners in Egyptian Governmental Hospitals, Zagazig City, Sharqia Governorate

OpenAIRE

RA Abbas; RAM Hammam; SS El-Gohary; LME Sabik; MS Hunter

2012-01-01

Background: Informal employment is common in developing countries, including Egypt. This type of employment may have significant consequences on mental health. Objectives: To determine the prevalence and risk factors of common mental disorders and substance abuse among temporary hired hospital cleaners. Methods: A cross-sectional study was conducted on 242 adult temporary cleaners and 209 permanent cleaners working in 4 governmental hospitals in Zagazig City, Sharqia Governorate, Egyp...

Early retirement among Danish female cleaners and shop assistants according to work environment characteristics and upper extremity complaints

DEFF Research Database (Denmark)

Jensen, Lone Donbæk; Bonde, Jens Peter Ellekilde; Christensen, Michael Victor

2016-01-01

-year cohort study with registry-based follow-up of 1430 female cleaners and 579 shop assistants. In subsequent analyses of female cleaners, disability pension and voluntary early retirement were modeled according to work characteristics and upper extremity complaints. RESULTS: The adjusted hazard rate...

Energy and rice quality aspects during drying of freshly harvested paddy with industrial inclined bed dryer

International Nuclear Information System (INIS)

Sarker, M.S.H.; Ibrahim, M. Nordin; Ab. Aziz, N.; Mohd. Salleh, P.

2014-01-01

Highlights: • We presented performance evaluation approach for industrial inclined bed paddy dryer. • Specific electrical energy consumption was 1.44–1.95 MJ/kg water evaporated. • Specific thermal energy consumption was 2.77–3.47 MJ/kg water evaporated. • Dryer yielded 1–4% higher head rice at drying temperature of 38–39 °C than 41–42 °C. • Dryers should be operated at 38–39 °C for 1–4% higher head rice at reasonable energy. - Abstract: The performance evaluation of any industrial dryer regarding energy consumption and product quality should be assessed to check its present status and to suggest for further efficient operation. An investigation was carried out to evaluate the impact of drying temperature and air flow on energy consumption and quality of rice during paddy drying with industrial inclined bed dryer (IBD) with average holding capacity of 15 ton in the selected complexes of Padiberas Nasional Berhad (BERNAS)-the national paddy custodian of Malaysia. In reducing paddy moisture content (mc) from 22% to 23% wet basis (wb) down to around 12.5% wb, the final mc, the specific electrical (in terms of primary energy) and the specific thermal energy consumption were found to be varied between 1.44 to 1.95 MJ/kg water evaporated and 2.77 to 3.47 MJ/kg water evaporated, respectively. Analysis revealed that the specific electrical energy consumption was around 20% lesser and the specific thermal energy consumption of IBDs was around 10% higher during drying with air temperature of 41–42 °C than drying with 38–39 °C in reducing paddy mc from 22% to 23% (wb) down to around 12.5% (wb). However, paddy being with almost same initial mc dried using drying temperature of 38–39 °C, IBDs yielded 1–4% higher head rice yield while milling recovery and whiteness were comparable at acceptable milling degree and transparency. The bed air flows between 0.27 and 0.29 m 3 m −2 s −1 resulted in higher head rice yield slightly while its

Field Performance Test of an Air-Cleaner with Photocatalysis-Plasma Synergistic Reactors for Practical and Long-Term Use

Directory of Open Access Journals (Sweden)

Tsuyoshi Ochiai

2014-10-01

Full Text Available A practical and long-term usable air-cleaner based on the synergy of photocatalysis and plasma treatments has been developed. A field test of the air-cleaner was carried out in an office smoking room. The results were compared to previously reported laboratory test results. Even after a treatment of 12,000 cigarettes-worth of tobacco smoke, the air-cleaner maintained high-level air-purification activity (98.9% ± 0.1% and 88% ± 1% removal of the total suspended particulate (TSP and total volatile organic compound (TVOC concentrations, respectively at single-pass conditions. Although the removal ratio of TSP concentrations was 98.6% ± 0.2%, the ratio of TVOC concentrations was 43.8% after a treatment of 21,900 cigarettes-worth of tobacco smoke in the field test. These results indicate the importance of suitable maintenance of the reactors in the air-cleaner during field use.

Laser cleaner development for decontamination of the primary water cooling system at nuclear power plants

International Nuclear Information System (INIS)

Minehara, Eisuke

2010-01-01

We recently have performed the feasibility studies to develop laser cleaners utilizing several laser oscillator and amplifier systems like femto-second free-electron lasers, water-jet guided lasers, Q-switched YAG lasers, fiber lasers. Whenever we used to clean the RI-contaminated surface using the lasers, we should focus enough laser power in the surface to evaporate instantly without melting. Therefore, as the contaminated being deeply located into the surface could be removed using any one set of the lasers, we found that every trial of laser cleaning could remove very well the RI contamination being located deeply. Our cold decontamination test using a model sample being Cobalt plated successfully has been performed to show a very high decontamination factor. In order to develop an usable laser cleaner, we plan to develop the prototype laser cleaner next year. (author)

Life-History Traits and Population Structure of Pederson Cleaner Shrimps Ancylomenes pedersoni.

Science.gov (United States)

Gilpin, Jessica A; Chadwick, Nanette E

2017-12-01

Cleaner organisms perform key functional roles in reducing rates of parasitism in marine communities. Pederson cleaner shrimps Ancylomenes pedersoni are major cleaners of reef fishes in the tropical western Atlantic and form obligate symbioses with host sea anemones. Information about their life-history traits would contribute to understanding how symbiosis impacts life-history evolution in crustaceans, but little is known about patterns of growth and reproduction in this anemone shrimp. We quantified growth, sexual reproduction, senescence, and mortality in individuals of A. pedersoni under laboratory conditions and their abundance and population size structure on coral reefs in St. Thomas, U.S. Virgin Islands. Von Bertalanffy growth curves were fitted to the data to determine age-size relationships, and the Beverton-Holt model was used to estimate mortality rates and size at maximum yield. Individuals grew rapidly when young, then slowed their growth after reaching sexual maturity at ~6 months. Individuals were gonochoric, with males attaining significantly smaller body sizes and shorter life spans than did females. Prior to death at <2 years, members of both genders exhibited senescence during which they ceased reproducing, shrank (females only), and decreased their activity levels over ~1-4 weeks. Field populations were abundant and composed mostly of juveniles during both years examined. Populations appeared to be stable but highly dynamic in terms of individuals, reaching maximum yield at 4 months of age. We conclude that obligate symbiosis with large sea anemones and cleaner mutualism with reef fishes both contribute to explaining aspects of the life history of Pederson shrimps, especially their apparent mating system of pure-search polygynandry. This life-history information also provides a scientific basis for sustainable fishery management and aquaculture of this key coral reef organism.

Mathematical modeling of a mixed flow spray dryer

International Nuclear Information System (INIS)

Kasiri, N.; Delkhan, F.

2001-01-01

In this paper a mathematical model has been developed to simulate the behavior of spray dryers with an up-flowing spray. The model is based on mass, energy and momentum balance on a single droplet , and mass and energy balances on the drying gas. The system of nonlinear differential equations thus obtained is solved to predict the changes in temperature, humidity, diameter, velocity components and the density of the droplets as well as the temperature and the humidity changes of the drying gas. The predicted results were then compared with an industrially available set of results. A good degree of proximity between the two is reported

Region specific changes in nonapeptide levels during client fish interactions with allopatric and sympatric cleaner fish.

Science.gov (United States)

Soares, Marta C; Cardoso, Sónia C; Mazzei, Renata; André, Gonçalo I; Morais, Marta; Gozdowska, Magdalena; Kalamarz-Kubiak, Hanna; Kulczykowska, Ewa

2017-01-01

Social relationships are crucially dependent on individual ability to learn and remember ecologically relevant cues. However, the way animals recognize cues before engaging in any social interaction and how their response is regulated by brain neuromodulators remains unclear. We examined the putative involvement of arginine vasotocin (AVT) and isotocin (IT), acting at different brain regions, during fish decision-making in the context of cooperation, by trying to identify how fish distinguish and recognize the value of other social partners or species. We hypothesized that the behavioural responses of cleaner fish clients to different social contexts would be underlain by changes in brain AVT and IT levels. We have found that changes in AVT at the level of forebrain and optic tectum are linked with a response to allopatric cleaners (novel or unfamiliar stimuli) while those at cerebellum are associated with the willingness to be cleaned (in response to sympatric cleaners). On the other hand, higher brain IT levels that were solely found in the diencephalon, also in response to allopatric cleaners. Our results are the first to implicate these nonapeptides, AVT in particular, in the assessment of social cues which enable fish to engage in mutualistic activities.

Evaluation of room air cleaners for the reduction of exposure and dose to indoor radon progeny

International Nuclear Information System (INIS)

Hopke, P.K.; Jensen, B.; Wasiolek, P.

1994-01-01

Since the proximate source of dose to the cells of the bronchial epithelium is the deposited radon progeny, the exposure and resulting dose could be reduced if the radon decay products were effectively removed from the indoor atmosphere. Thus, room air cleaners could be effective in reducing the risks associated with indoor radon. However, because of the short half-life of 218 Po, it grows back quickly and in the altered aerosol conditions that are produced by the presence of an air cleaner, the exposure/dose conditions as well as the magnitude of the dose can be substantially changed. To examine the nature of the exposure of individuals in normally occupied homes and to determine the effect of various types of room air cleaners on the exposure to and dose from the indoor radon progeny, a series of measurements have been made using an automated graded screen array system. Two extended experiments were performed in homes in Arnprior, Ontario and Parishville, NY, in which filtration systems, a positive ion electrostatic precipitator, and ioniser/fan systems have been tested for their ability to remove both airborne radioactivity and particles. In both experiments, measurements were made over one week periods with an air cleaner operating and the distributions of exposure are compared with measurements of the background conditions when no cleaner is functioning. The doses to both basal and secretory cells of the bronchial epithelium in the first eight generations of the bronchus were calculated using the model developed by James and their distributions are compared among the various exposure conditions. In most cases the presence of the air cleaner reduced the exposure to radon progeny. However, the reductions in dose were generally substantially smaller than the reductions in exposure. In the intercomparisons of the two filtration units and the two identical ioniser/fan systems, the units generally behaved in a similar manner. The results of this substantial set of

Experimental investigation of a solar dryer with natural convective heat flow

Energy Technology Data Exchange (ETDEWEB)

Gbaha, P.; Yobouet Andoh, H.; Kouassi Saraka, J. [Laboratoire d' Energies d' Energies Nouvelles et Renouvelables, Institut National Polytechnique Felix Houphoeuet-Boigny, B.P. 1526 Yamoussoukro (Ivory Coast); Kamenan Koua, B.; Toure, S. [Laboratoire d' Energie Solaire, Universite de Cocody, 22 B.P.: 582, Abidjan 22 (Ivory Coast)

2007-09-15

A direct type natural convection solar dryer is designed. It is constructed in local materials (wood, blades of glass, metals) then tested experimentally in foodstuffs drying (cassava, bananas, mango). It is about an experimental approach which consists in analyzing the behavior of the dryer. The study relates mainly kinetics and establishment of drying heat balances. The influence of significant parameters governing heat and mass transfers, such as solar incident radiation, drying air mass flow and effectiveness, is analyzed in order to evaluate its thermal performances. Experimental data can be represented by empirical correlations of the form M(t)=M{sub i}exp(-kt) for representation of drying process. The resolution of these drying equations makes-possible to predict total drying time of each product. Moreover, this drying process allows to reduce the moisture content of cassava and sweet banana approximately to 80% in 19 and 22 h, respectively to reach the safety threshold value of 13%. This value permits the conservation of these products about one year without deterioration. The determination of parameters, like ambient temperature, drying chamber temperature, drying air mass flow and incident heat fluxes, allow to predict the drying effectiveness for modeling and refining the dimensioning of the elaborate prototype. (author)

Implementing Cleaner Technologies as a means of minimising waste production

DEFF Research Database (Denmark)

Wenzel, Henrik

2002-01-01

This article gives an overview of how Cleaner Production methods may contribute to minimising waste formation as well as showing energy and resource savings. It introduces the tools and procedures used when working in this field. It also illustrates the theoretical approach by using examples from...

Effect of separation and drainage of condensate on dehumidification in a refrigerated dryer; Reito joshitsuki ni okeru gyoshukusui bunri/haishutsu noryoku no joshitsu seino ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Goto, H.; Ichinose, T. [SMC Corp., Tokyo (Japan); Tanzawa, Y.; Hashizume, T. [Waseda Univ., Tokyo (Japan). Science and Engineering Research Lab.

1995-11-15

The representative refrigerated dryer as the compressed air dryers is one in which air was cooled at rather low temperature by working medium of refrigerators, and the dew point was decreased with increase of pressure, and air with low relative humility called as the dried air was obtained again by heating. In this paper, for clarifying effect of separation and drainage of condensate on dehumidification in a refrigerated dryer in relation to shape of a main cooler and a precool-reheater and air temperature of each part, calculation and experimental investigation were conducted. In a refrigerated dryer, condensate happened in the precool part of a precool-reheater and a main cooler, and this would give rise to reduce of separation and drainage of condensate and increase of thermal loads of each heat exchange, and would made dehumidification low. For a fact that decrease of separation and drainage of condensate in a main cooler would bring out heat conduction with phase change in the reheating part of a precool-reheater, it has a profitable side, but it is not desirable for ability of dryers. 6 refs., 9 figs., 1 tab.

Design and development of automatic sharia compliant wheelchair wheels cleaner

Science.gov (United States)

Shaari, Muhammad Farid; Rasli, Ibrahim Ismail Mohammad; Jamaludin, M. Z. Z. Wan; Isa, W. A. Mohamad; M., H.; Rashid, A. H. Abdul

2017-04-01

Sharia compliant wheelchair wheel cleaner was developed in order to assist the muslim Person with Disabilities (PWD) to pray in the mosque without leaving their wheelchair because of the filthy wheels. Though there are many wheelchair wheel cleaning system in the market, it is very rare to find sharia compliant cleaning system that applies sertu concept which is one of the cleaning and purification technique in Islamic practice. The sertu concept is based on 6:1 ratio that refers to the six times pipe water cleaning and one time soiled water cleaning. The development process consists of design stage, fabrication and system installation stage and followed by testing stage. During the design stage, the proposed prototype underwent design brainstorming, operation programming and structural simulation analysis. Once fabricated, the cleaner prototype underwent was tested. The results showed that the prototype can cater load up to 100kg with 1.31×10-6 mm shaft bending displacement. The water ejection timing varied approximately 3% compared to the program.

78 FR 20842 - Energy Conservation Program: Energy Conservation Standards for Residential Clothes Dryers and...

Science.gov (United States)

2013-04-08

... DeLonghi); energy and environmental advocates (American Council for an Energy Efficient Economy (ACEEE... DEPARTMENT OF ENERGY 10 CFR Part 430 [Docket Number EERE-2013-BT-STD-0020] RIN 1904-AC98 Energy Conservation Program: Energy Conservation Standards for Residential Clothes Dryers and Room Air Conditioners...

Preservation of fruits and vegetables using solar dryers. A comparative study for solar and natural drying of grapes, figs, tomatoes and onions. IV. temperature measurements, calculating the generated energy and dryer efficiency during drying

International Nuclear Information System (INIS)

Sehery, A.A.; Gallali, Y.M.; Shoshan, H.

2000-01-01

This study has taken four axis, first, design and construction of the dryer, secondly, microbial load determination, thirdly, chemical and sensory evaluation data. The results of these three parts were published earlier at the International Congress on Application of Solar and Renewable Energy, Food Science and Technology and World Renewable Energy Congress V, Cairo, Egypt, 1992, 1996 and Florence, Italy, 1998, respectively. The whole study was oriented towards comparing the solar (three modes, direct, indirect, and mixed) and natural drying. The fourth part of the study is dealing with some parameters affecting drying as temperature measurement, calculating the generated energy and the dryer efficiency during drying periods. Drying temperature is considered the most important factor in the drying operation, since the accuracy of temperature measurement gives the correct results and right indication for the approval of these scientific methods in the drying operation and the design of solar dryers. In this project, we depended on temperature measurements at different points by means of thermocouples fixed in the heat collector and the drying chamber. The average temperature outside the dryer ranged from 21-41 degree C. That of the heat collector were 40-75 degree C and those of the drying chamber were in the range of 40-73 degree C. The radiation measurements calculated depending on the results recorded by the solar center instruments from 5/8/95 - 16/10/95. The thermal energy existing from the heat collector to the drying chamber during the drying period was measured using the equation of Holland. From the investigation results, we can conclude that in all trials, solar drying was a more efficient method for drying all samples of fruits and vegetables, especially for grapes, figs and onion. Grapes dried using mixed mode from 83 % to 30 % moisture in 4 days at an average temperature of 55 degree C while natural drying reduced the moisture to 57% for the same period

Cleaner production technology for the NDT industry

International Nuclear Information System (INIS)

Relunia, Estrella D.; Mateo, Alejandro J.

2001-01-01

This paper discusses te wastes generated from the conduct of nondestructive testing (NDT) techniques and operations like NDT film processing and the systems to reduce water pollution and the film system quality control. Discussions on clean technology production concepts and philosophy is also discussed. A case study on cleaner production technology where a process and equipment modifications and a product substitution were implemented is presented. The equipment modification and product substitution eliminated the use of 1,1,1-trichloroethane in its cleaning operation. (Author)

Modelling and simulation of processes by smart sensing : a solar dryer for plant material

Energy Technology Data Exchange (ETDEWEB)

Correa, E.C.; Diezma, B.; Ruiz-Altisent, M. [LPF-TAGRALIA Univ. Politecnica, CENIM-CSIC, Madrid (Spain)

2010-07-01

This paper reported on a study in which as small wood dryer was modelled. Studies have shown that properly designed solar dryers may prove to be energy saving devices for drying processes. The drying rate expressed as -dX/dt=f/X (where X is DB wood moisture content), allows to identify 2 different kinetics, notably for high X values or fibre saturation point (FSP) and for X values under FSP, in which diffusion is the mechanism that governs a decreasing drying rate at this stage. The complex drying rate model developed in this study made it possible the determine the wood and convective mass transfer at the wood-air interface. Validation and application to fruit and plant drying cycles is currently underway. Three different proposed models are used in the software for a smart sensor system, which is based on Sensirion sensors for temperature and relative humidity in the air, and thermocouples for timber temperature.

EVALUATION AND ACTIONS OF CLEANER PRODUCTION IN GALVANIC INDUSTRY OF THE VILLA CLARA PROVINCE

Directory of Open Access Journals (Sweden)

Petra G. Velazco Pedroso

2015-10-01

Full Text Available In this paper, the assessment results accomplished in different processes of the galvanic industry are presented and it is taking into account the application of good practices and measures of Cleaner Production. The main critical points in the processes of metallic coating were identified; and the characterization of the effluents generated by the installation is done. A number of technological changes in the processes are proposed, as well as the introduction of cleaner production measures which contribute to increase the efficiency and safety of processes, reduce risks and improvements to internal operations. It provides advantages of economic, environmental and social nature for the galvanic industry due to the minimizing of the impacts on environment, because the sewage and its pollutant load are reduced. Besides, we can save water, energy and raw materials. The economic evaluation showed the feasibility of applying the Cleaner Production (PML measures proposed with a Net Present Value (NPV of $109 696.26, and an Internal Rate of Return (IRR of 64 % value and payback period lower than two years.

Determination of Ammonia in Household Cleaners: An Instrumental Analysis Experiment.

Science.gov (United States)

Graham, Richard C.; DePew, Steven

1983-01-01

Briefly discusses three techniques for assessing amount of ammonia present in household cleaners. Because of disadvantages with these methods, the thermometric titration technique is suggested in which students judge the best buy based on relative cost of ammonia present in samples. Laboratory procedures, typical results, and reactions involved…

Alterations in fruit and vegetable beta-carotene and vitamin C content caused by open-sun drying, visqueen-covered and polyethylene-covered solar-dryers.

Science.gov (United States)

Ndawula, J; Kabasa, J D; Byaruhanga, Y B

2004-08-01

This study investigated the effects of three drying methods (open sun drying, visqueen-covered solar dryer and polyethylene-covered solar dryer) on b-carotene and vitamin C content of edible portions of mango fruit (Mangifera indica) and cowpea leaves (Vigna unguiculata). Commercial samples were analysed for vitamin C by titrimetry and b-carotene by spectrophotometry at 450 nm. Differences in vitamin retention and loss associated with the three drying methods were assessed by analysis of variance and least significant difference (LSD) at (pdrying. Open sun drying method caused the greatest b-carotene and vitamin C loss (58% and 84% respectively), while the visqueen-covered solar dryer caused the least loss (34.5% and 71% respectively). Blanching cowpea leaves improved b-carotene and vitamin C retention by 15% and 7.5% respectively. The b-carotene and vitamin C content of fresh ripe mango fruit was 5.9 and 164.3 mg/100g DM respectively. Similar to effects on cowpea leaves, the mango micronutrient content decreased (pdrying. The open sun drying method caused the greatest b-carotene (94.2%) and vitamin C (84.5%) loss, while the visqueen-covered solar dryer caused the least (73 and 53% respectively). These results show that the three solar drying methods cause significant loss of pro-vitamin A and vitamin C in dried fruits and vegetables. However, open sun drying causes the most loss and the visqueen-covered solar dryer the least, making the later a probable better drying technology for fruit and vegetable preservation. The drying technologies should be improved to enhance vitamin retention.

Survey on solar dryers for drying of food and wood in Ghana

Energy Technology Data Exchange (ETDEWEB)

Oestergaard Jensen, S.; Correll Frank, F. [Danish Technological Inst., Taastrup (Denmark); Floejgaard Kristensen, E. [Danish Inst. of Agricultural Sciences, Tjele (Denmark)

1999-11-01

The survey was conducted as a part of the project 'Test and Research Project into the Drying of Food and Wood Products with Solar Heat'. The aim of the survey was to investigate the need for drying of food and wood in Ghana and the already existing experience on solar drying in order to form a basis for the initial decisions within the project concerning the location of three demonstration solar dryers for crops, fish and wood, which species to dry and the type of solar dryers. The project deals with transfer of knowledge in the field of drying of crops and wood and solar air heating systems from Denmark to Ghana. The aim of the survey was, therefore, also to give the Danish experts an impression of the conditions in Ghana in order to facilitate an appropriate design of the solar dryers. Three of the four Danish partners participated in the survey. The fourth Danish partner - the manufacturer of solar heating systems Aidt Miljoe - are already familiar with the conditions in Ghana due to an earlier project in Ghana. The survey was planed by the Energy Commission of Ghana, the Ghanaian partner and consultants: DENG, University of Science and Technology, Kumasi and Econkoad. The time schedules for the survey - one for crops/fish and one for wood - are found in Annex A. The schedules were very well prepared and the sites to visit were well chosen. The visits gave the Danish experts a good overview of the situation in Ghana in the field of post harvesting of crops, handling of fish, drying and manufacturing of wood and existing experience on solar drying. The schedules included a large variety of different information and impressions e.g. ranging from large sawmill to small carpenters and workshops. Despite tight schedules the consultants managed to stick very close to the time schedules shown in Annex A. (au)

Evaluation of cleaner production options in dyeing and printing industry: Using combination weighting method

Science.gov (United States)

Kang, Hong; Zhang, Yun; Hou, Haochen; Sun, Xiaoyang; Qin, Chenglu

2018-03-01

The textile industry has a high environmental impact so that implementing cleaner production audit is an effective way to achieve energy conservation and emissions reduction. But the evaluation method in current cleaner production audit divided the evaluation of CPOs into two parts: environment and economy. The evaluation index system was constructed from three criteria of environment benefits, economy benefits and product performance; weights of five indicators were determined by combination weights of entropy method and factor weight sorting method. Then efficiencies were evaluated comprehensively. The results showed that the best alkali recovery option was the nanofiltration membrane method (S=0.80).

Simulation of exhaust gas heat recovery from a spray dryer

International Nuclear Information System (INIS)

Golman, Boris; Julklang, Wittaya

2014-01-01

This study explored various alternatives in improving the energy utilization of spray drying process through the exhaust gas heat recovery. Extensible and user-friendly simulation code was written in Visual Basic for Applications within Microsoft Excel for this purpose. The effects of process parameters were analyzed on the energy efficiency and energy saving in the industrial-scale spray drying system with exhaust gas heat recovery in an air-to-air heat exchanger and in the system with partial recirculation of exhaust air. The spray dryer is equipped with an indirect heater for heating the drying air. The maximum gains of 16% in energy efficiency and 50% in energy saving were obtained for spray drying system equipped with heat exchanger for exhaust air heat recovery. In addition, 34% in energy efficiency and 61% in energy saving for system with recirculation of exhaust air in the present range of process parameters. The high energy efficiency was obtained during drying of large amount of dilute slurry. The energy saving was increased using the large amount of hot drying air. - Highlights: • We model industrial-scale spray drying process with the exhaust gas heat recovery. • We develop an Excel VBA computer program to simulate spray dryer with heat recovery. • We examine effects of process parameters on energy efficiency and energy saving. • High energy efficiency is obtained during drying of large amount of dilute slurry. • Energy saving is increased using the large amount of hot drying air

Mitigation of the effective dose of radon decay products through the use of an air cleaner in a dwelling in Okinawa, Japan

International Nuclear Information System (INIS)

Kranrod, Chutima; Tokonami, Shinji; Ishikawa, Tetsuo; Sorimachi, Atsuyuki; Janik, Miroslaw; Shingaki, Reina; Furukawa, Masahide; Chanyotha, Supitcha; Chankow, Nares

2009-01-01

Field measurements were conducted to assess the effects of an air cleaner on radon mitigation in a dwelling with a high radon concentration in Okinawa, Japan. The measurements included indoor radon concentration, individual radon progeny concentration, equilibrium equivalent concentration of radon (EECRn), unattached fraction, and size distribution of aerosol-attached radon progeny. These measurements were conducted in a 74 m 3 room with/without the use of an air cleaner. The results showed that the mean radon concentration during the measurement was quite high (301 Bq m -3 ). The operation of air cleaner decreased the radon progeny activity concentration, EECRn and equilibrium factor by 33%, 57% and 71%, respectively, whereas the unattached fraction increased by 174%. In addition, the activity concentration of attached radon progeny in the accumulation mode (50-2000 nm) was obviously deceased by 42%, when the air cleaner was operated. According to dosimetric calculations, the operation of air cleaner reduced the effective dose due to radon progeny by about 50%.

The effect of fan speed control system on the inlet air temperature uniformity in a solar dryer

Directory of Open Access Journals (Sweden)

S. F Mousavi

2015-09-01

Full Text Available Introduction: Drying process of agricultural products, fruits and vegetables are highly energy demanding and hence are the most expensive postharvest operation. Nowadays, the application of control systems in different area of science and engineering plays a key role and is considered as the important and inseparable parts of any industrial process. The review of literature indicates that enormous efforts have been donefor the intelligent control of solar driers and in this regard some simulation models are used through computer programming. However, because of the effect of air velocity on the inlet air temperature in dryers, efforts have been made to control the fan speed based ont he temperature of the absorber plate in this study, and the behavior of this system was compared with an ordinary dryer without such a control system. Materials and methods: In this study, acabinet type solar dryer with forced convection and 5kg capacity of fresh herbs was used. The dryer was equipped with a fan in the outlet chamber (the chimney for creating air flow through the dryer. For the purpose of research methods and automatic control of fan speed and for adjusting the temperature of the drying inlet air, a control system consisting of a series of temperature and humidity sensors and a microcontroller was designed. To evaluatethe effect of the system with fan speed control on the uniformity of air temperature in the drying chamber and hence the trend of drying process in the solar dryer, the dryer has been used with two different modes: with and without the control of fan speed, each in twodays (to minimize the errors of almost the same ambient temperature. The ambient air temperature during the four days of experiments was obtained from the regional Meteorological Office. Some fresh mint plants (Mentha longifolia directly harvested from the farm in the morning of the experiment days were used as the drying materials. Each experimental run continued for 9

Rancang Bangun Vacuum Cleaner Dengan Pengendali Nirkabel Menggunakan Modul Rf Data Transceiver Ys-1020ub Berbasis Mikrokontroler At89s52

Directory of Open Access Journals (Sweden)

IGAP Raka Agung

2012-12-01

Full Text Available Kebersihan merupakan hal yang sangat penting untuk menjaga kesehatan kita, khususnya kebersihan rumah. Rumah yang bersih sangat mempengaruhi kesehatan para penghuninya. Debu adalah kotoran yang paling sering mengotori rumah kita terutama pada bagian lantai. Setiap hari kita harus membersihkan rumah dari debu yang ada pada lantai untuk menjaga kebersihan sekaligus kesehatan kita. Dalam membersihkan lantai rumah dari  debu sering menyita banyak waktu dan tenaga. Vacuum cleaner terkendali nirkabel menggunakan Modul RF Data Transceiver YS-1020UB berbasis mikrokontroler AT89S52 merupakan salah satu solusi untuk membersihkan lantai rumah dari kotoran debu.  Vacuum cleaner ini menggunakan enam buah motor DC yaitu dua motor DC penyedot debu, dua motor DC penentu arah maju, mundur, belok kanan, dan belok kiri, serta dua motor DC penentu arah geser kanan dan geser kiri.  Vacuum cleaner ini dapat dikendalikan dengan dua mode operasi yaitu mode manual dan otomatis. Pada mode manual vacuum cleaner ini dikendalikan menggunakan remote control, dengan tranmisi nirkabel memakai transceiver YS-1020UB. Sedangkan pada mode otomatis  vacuum cleaner ini menggunakan empat buah sensor jarak untuk menghindari tabrakan pada dinding.  Vacuum cleaner dengan pengendali nirkabel menggunakan modul RF Data Transceiver YS-1020UB berbasis mikrokontroler AT89S52 sudah bisa membersihkan debu lantai sehingga lantai bersih dari debu.

Sustainability in pelletizing iron ore through the Industrial Ecology and Cleaner Production Program

Directory of Open Access Journals (Sweden)

Cristiano Farias Coelho

2013-06-01

Full Text Available This study aims to analyze the practices of a pelletizing iron ore industry with respect to adoption of pollution prevention measures, suggested by applying the concepts of Cleaner Production and Material Flow Analysis. The technical procedure adopted was the case study, the data collection was done through direct observation, with field research and literature review. The main results were obtained from analysis of company reports available to the public, but require a more detailed quantification of data. The study concludes that the identification of environmental opportunities is possible through the proposed implementation of Cleaner Production program, which provides better results when combined with the precepts of the industrial ecology tool, the Material Flow Analysis.

Cleaner Production Applied in a Small Furniture Industry in Brazil: Addressing Focused Changes in Design to Reduce Waste

Directory of Open Access Journals (Sweden)

Carlos Mario Gutiérrez Aguilar

2017-10-01

Full Text Available The wood industry is known for being among the biggest resource consumers, having a relatively low yield. The wood furniture industry as part of the wood industry also remains a big generator of residues and a big consumer of resources. Diverse solutions and technologies have been developed to deal with the residues generated, but those technologies are mostly applied at the end of the production chain with limited results. Cleaner production represents a program based on continuous strategies applied to a more sustainable use of materials and energy, minimizing waste and pollution. This paper presents a case study of a cleaner production program developed in a small furniture industry in Salvador de Bahia, Brazil, applying the concepts of cleaner production with parameters of ecodesign developed for the furniture industry. The object of study was the production of a wooden chair made from eucalyptus wood. The application of the cleaner production program and ecodesign parameters allowed a detailed characterization of the waste, resulting in opportunities for a reduction of the use of raw material by 30%, a reduction in waste by 49% and allowing a reduction in energy by 36% due to simplification of the productive process. Among the strategies applied were reshaping pieces, redesigning, and the substitution of materials. The results suggest that despite the existence of more complex environmental methods and approaches, the application of cleaner production plus ecodesign parameters could be more achievable for micro and small furniture industries.

Control and automatic alignment of the output mode cleaner of GEO 600

Energy Technology Data Exchange (ETDEWEB)

Prijatelj, M; Grote, H; Degallaix, J; Hewitson, M; Affeldt, C; Leong, J; Lueck, H; Strain, K A; Wittel, H; Willke, B; Danzmann, K [Max-Planck-Institut fuer Gravitationsphysik (Albert-Einstein-Institut) and Leibniz Universitaet Hannover, Callinstr. 38, 30167 Hannover (Germany); Hild, S; Freise, A, E-mail: mirko.prijatelj@aei.mpg.d [School of Physics and Astronomy, University of Birmingham, Edgbaston, Birmingham, B15 2TT (United Kingdom)

2010-05-01

The implementation of a mode cleaner at the output port of the GEO 600 gravitational wave detector will be part of the upcoming transition from GEO 600 to GEO-HF. Part of the transition will be the move from a heterodyne readout to a DC readout scheme. DC readout performance will be limited by higher order optical modes and control sidebands present at the output port. For optimum performance of DC readout an output mode cleaner (OMC) will clean the output beam of these contributions. Inclusion of an OMC will introduce new noise sources whose magnitudes needed to be estimated and for which new control systems will be needed. In this article we set requirements on the performance of these control systems and investigate the simulated performance of different designs.

Analysis of Energy Consumption of "Compression Heat" Pressure Heat Dryer%“压缩热”干燥机能耗分析

Institute of Scientific and Technical Information of China (English)

李申

2015-01-01

作为典型的热质交换设备，吸附干燥器再生能量是被吸水量锁定的。总耗能受到吸附剂本身物理性质的制约，可用“质量守恒”与“能量守恒”两大定律来解释其能耗过程。各类吸附干燥器能耗量都要通过“能量衡算”来确定。“压缩热”干燥器与其他一切加热干燥器一样采取了“长周期”工作循环制，解吸环节无效热损很大。无热再生干燥器则采用了“短周期”工作制，为实际耗气量减少留有了较大的空间。%As the typical heat and mass transfer equipment, the energy of regenerative desiccant dryers is limited by water absorption. The total energy consumption is restricted by the physical properties of the adsorbent, which can be explained through two laws of conservation of mass and energy conservation. The energy consumption in each absorption dryers should be determined by“energy balance”.“Compression heat”dryer adopts“long-period”working cycle system as other heating dryers, in which invalid heat losses are great in desorption process. However, regenerated dryer without heat adopts“short-period”working cycle system, which provides greater space for actual gas consumption reduction.

Trochanteric Stress Fracture in a Female Window Cleaner

OpenAIRE

Lee, Bong-Jin; Song, Jyewon

2016-01-01

Stress fractures may occur at various sites in the femur including the head, neck, shaft, supracondylar and condylar regions. To the best of our knowledge, stress fracture occurring in the trochanteric region has not been previously reported. We report here a case of trochanteric stress fracture in a 53-year-old female window cleaner treated with hip nailing without adverse consequences. Careful consideration of this entity is needed when evaluating patients who have repetitive jumping up and...

TNO moving forward ... to a safer, cleaner and more efficient mobility

NARCIS (Netherlands)

Bleijenberg, A.N.

2008-01-01

This book provides an impression of how we are contributing to cleaner, safer and more efficient mobility in Europe, helping our customers from concept to implementation and from engineering solutions to strategic advice. Our knowledge is derived to a significant extent from European research

Biodiesel from plant seed oils as an alternate fuel for compression ignition engines-a review.

Science.gov (United States)

Vijayakumar, C; Ramesh, M; Murugesan, A; Panneerselvam, N; Subramaniam, D; Bharathiraja, M

2016-12-01

The modern scenario reveals that the world is facing energy crisis due to the dwindling sources of fossil fuels. Environment protection agencies are more concerned about the atmospheric pollution due to the burning of fossil fuels. Alternative fuel research is getting augmented because of the above reasons. Plant seed oils (vegetable oils) are cleaner, sustainable, and renewable. So, it can be the most suitable alternative fuel for compression ignition (CI) engines. This paper reviews the availability of different types of plant seed oils, several methods for production of biodiesel from vegetable oils, and its properties. The different types of oils considered in this review are cashew nut shell liquid (CNSL) oil, ginger oil, eucalyptus oil, rice bran oil, Calophyllum inophyllum, hazelnut oil, sesame oil, clove stem oil, sardine oil, honge oil, polanga oil, mahua oil, rubber seed oil, cotton seed oil, neem oil, jatropha oil, egunsi melon oil, shea butter, linseed oil, Mohr oil, sea lemon oil, pumpkin oil, tobacco seed oil, jojoba oil, and mustard oil. Several methods for production of biodiesel are transesterification, pre-treatment, pyrolysis, and water emulsion are discussed. The various fuel properties considered for review such as specific gravity, viscosity, calorific value, flash point, and fire point are presented. The review also portrays advantages, limitations, performance, and emission characteristics of engine using plant seed oil biodiesel are discussed. Finally, the modeling and optimization of engine for various biofuels with different input and output parameters using artificial neural network, response surface methodology, and Taguchi are included.

Modelling the drying kinetics of green peas in a solar dryer and under open sun

Energy Technology Data Exchange (ETDEWEB)

Sunil [Department of Mechanical Engineering, BRCM CET Bahal, Haryana–127028 (India); Varun [Department of Mechanical Engineering, NIT Hamirpur, (H.P.)–177005 (India); Sharma, Naveen [Department of Mechanical and Industrial Engineering, IITR, (U.K.)–247667 (India)

2013-07-01

The drying kinetics of green peas was investigated in an indirect solar dryer and under open sun. The entire drying process took place exclusively in falling rate period. The constant rate period was absent from the drying curves. The rehydration capacity was also determined for peas dried in solar dryer and under open sun. The rehydration capacity of solar dried peas was found higher than open sun dried peas. The drying data obtained from experiments were fitted to eight different mathematical models. The performance of these models was examined by comparing the coefficient of correlation (R2), sum of squares error (SSE), mean squared error (MSE) and root mean square error (RMSE) between observed and predicted values of moisture ratios. Among these models, the thin layer drying model developed by Page showed good agreement with the data obtained from experiments for bottom tray. The Midilli et al. model has shown better fit to the experimental data for top tray and open sun than other models.

Analysis of heat recovery from a spray dryer by recirculation of exhaust air

International Nuclear Information System (INIS)

Golman, Boris; Julklang, Wittaya

2014-01-01

Highlights: • We study a spray dryer with heat recovery by partial recirculation of exhaust air. • We examine effects of process parameters on energy efficiency and energy savings. • Decreasing drying air temperature and flow rate will increase energy efficiency. • Increasing recirculation ratio and slurry feed rate will increase energy efficiency. - Abstract: Model simulations were employed to investigate the influences of process parameters on the energy recovery in spray drying process that partially recycle the exhaust drying gas. The energy efficiency and energy saving were studied for various values of recirculation ratios with respect to the temperature and flow rate of the drying air, slurry feed rate and concentration of slurry in spray drying of advanced ceramic materials. As a result, significant gains in energy efficiency and energy saving were obtained for a spray drying system with high recirculation ratio of exhaust air. The high slurry feed rate and the low slurry concentration, inlet drying air temperature and drying air flow rate enhanced the energy efficiency of spray drying system. However, the high energy saving was obtained in spray dryers operating at low slurry feed rate and high slurry concentration

Influence of the process control on the thermal energy requirement of convection dryers in the brick industry; Einfluss der Prozessfuehrung auf den thermischen Energiebedarf von Konvektionstrocknern in der Ziegelindustrie

Energy Technology Data Exchange (ETDEWEB)

Tretau, Anne

2008-06-10

Brick manufacturing demands high amount of energy. The energy flow analysis inside the brick factory shows that the convective drying of green bricks consumes more than half of the total thermal energy required for brick manufacturing. Therefore this paper deals with the theoretical analysis and investigation for the energy requirement of green bricks. For this, a physical-based model has been developed, which describes the dependence of drying-kinetics as well as the energy-requirement interims of the process parameter like mass of the supply air. It turns out that the specific energy requirement substantially depends on temperature and humidity of the ambience air and also supply air mass flow and its temperature. Due to the continuous temperature rise of the green bricks during the second drying section the specific energy requirement increases significantly with the progressive motion of the drying in a chamber dryer. This is due to the fact that the green brick as well as the air conditioning distance more and more from the cooling limit. Just a low part of the dryer exhaust air is saturated. The exhaust air is continuously sucked out and the green bricks are pulled inside the dryer. So the exhaust air has a relatively higher water saturation. On general, continuous dryers have a lower energy requirement than chamber dryer. For the both types of dryers, the mathematical model shows that the increasing of the supply air temperature combined with a commensurate subsidence of supply air mass flow, results in a reduction of drying energy requirement. The change of other essential parameters of drying like green brick thickness, and density as well as the moisture diffusion coefficient, and the vapour diffusity which are only important in the second drying section are of comparatively negligible effect. The developed mathematical model is successfully implemented for the energy investigation in the industrial dryers. The increase in supply air temperature results

The progress of test and study for steam dryer in vertical steam generator

International Nuclear Information System (INIS)

Ding Xunshen

1993-01-01

Constructions, tests and test results are reviewed for three types of steam generator dryer that are concentric vertical corrugated separator, centrifugal conic separator and chevron separator. The last type is considered as the best one in comparison, which has been applied to Qinshan 300 MW steam generator. A number of pertinent remarks to draining scheme, hydraulic loss reduction, and conduct of test are given based on experiences

The hydrodynamic basis of the vacuum cleaner effect in continuous-flow PCNL instruments: an empiric approach and mathematical model.

Science.gov (United States)

Mager, R; Balzereit, C; Gust, K; Hüsch, T; Herrmann, T; Nagele, U; Haferkamp, A; Schilling, D

2016-05-01

Passive removal of stone fragments in the irrigation stream is one of the characteristics in continuous-flow PCNL instruments. So far the physical principle of this so-called vacuum cleaner effect has not been fully understood yet. The aim of the study was to empirically prove the existence of the vacuum cleaner effect and to develop a physical hypothesis and generate a mathematical model for this phenomenon. In an empiric approach, common low-pressure PCNL instruments and conventional PCNL sheaths were tested using an in vitro model. Flow characteristics were visualized by coloring of irrigation fluid. Influence of irrigation pressure, sheath diameter, sheath design, nephroscope design and position of the nephroscope was assessed. Experiments were digitally recorded for further slow-motion analysis to deduce a physical model. In each tested nephroscope design, we could observe the vacuum cleaner effect. Increase in irrigation pressure and reduction in cross section of sheath sustained the effect. Slow-motion analysis of colored flow revealed a synergism of two effects causing suction and transportation of the stone. For the first time, our model showed a flow reversal in the sheath as an integral part of the origin of the stone transportation during vacuum cleaner effect. The application of Bernoulli's equation provided the explanation of these effects and confirmed our experimental results. We widen the understanding of PCNL with a conclusive physical model, which explains fluid mechanics of the vacuum cleaner effect.

CASE STUDY: Nepal — A cleaner city and better health in Kathmandu

International Development Research Centre (IDRC) Digital Library (Canada)

2003-04-07

Apr 7, 2003 ... CASE STUDY: Nepal — A cleaner city and better health in Kathmandu .... Dr Joshi believes that blending science and a recognition of the social ... One example of where AMESH was applied was in analyzing why the ward ...

Temperature and energy consumption for clothing dryer; Temperatura e consumo de energia em secadora de vestuario

Energy Technology Data Exchange (ETDEWEB)

Ribeiro, Jefferson Almeida; Magalhaes Filho, Paulo [UNESP, Guaratingueta, SP (Brazil). Faculdade de Engenharia. Dept. de Energia]. E-mail: pfilho@feg.unesp.br

2000-07-01

The cloth dehumidification is done by hot air circulation through it in dryers. The air circulation is done by a fan, run by an electrical motor, and the air temperature raise, which goes through the cloths aiming their moisture dragging, is gotten by the heat dissipation from electrical resistance. This work shows the results of an experimental modeling, examining the behavior of several kinds of cloth in a vertical suspense-type dryer, such as: polyester, cotton-spandex, flannel, blue-jeans and viscose rayon. It was analyzed the behavior of the moisture content in these cloths related to controlled-temperature-air flows, determining the needed heat to reach the required drying standards. The drying device fans were tested for the determination of their flow rate and energy consumption, establishing a flow rate versus consumption relationship. Comparative results among the various kinds of cloths are presented. (author)

Visibility and Social Recognition as Psychosocial Work Environment Factors among Cleaners in A Multi-Ethnic Workplace Intervention

OpenAIRE

Hviid, Kirsten; Smith, Louise Hardman; Frydendall, Karen Bo; Flyvholm, Mari-Ann

2012-01-01

This article focuses on the psychosocial work environment of immigrant cleaners at a Danish workplace. Today, many cleaners working in Danish cleaning jobs are women from the established immigrant communities, but also labour migrants from the newer EU member states have found their way to the cleaning industry. Studies have drawn attention to immigrants low position in the cleaning industry and their increased risk of work injuries. This article is based on a case study of an intervention ca...

Removal of SO2 and NO/sub x/ from flue gas by means of a spray dryer/electron beam combination: a feasibility study

International Nuclear Information System (INIS)

Helfritch, D.J.; Feldman, P.L.; Ray, A.B.; Morgan, J.R.; Hildreth, G.A.

1982-04-01

This study examines the feasibility of adding an electron beam between the spray dryer and the fabric filter of dry scrubber flue gas desulfurization (FGD) systems. The beam promises effective removal of nitrogen oxides (NO/sub x/) and sulfur dioxide (SO 2 ), even at higher coal-sulfur levels than usually economic for dry scrubbers. The beam excites gas molecules, promoting reactions that convert SO 2 and NO/sub x/ to acids that then react with calcium compounds and are removed by the filter. Concerns examined here are feasibility and waste disposal. The cost findings are promising for both manufacture and operation. The system uses commercially available components. The relatively low temperatures and high humidity downstream of the spray dryer favor economic beam operation. The beam removes SO 2 , so the dryer can be run for economy, not high removal. The beam's incidental heating effect reduces reheat cost. Safe landfilling of the nitrate-rich waste appears practical, with leachate carrying no more nitrate than natural rain and dustfall. We expect natural pozzolanic reactions between alumina-silica compounds in the fly ash and lime compounds from the spray dryer to form an impermeable concrete-like material within 10 days after landfilling. Dry scrubber with electron beam appears competitive with commercial FGD systems, and we recommend a pilot scale operation

Experimental investigation on energy and exergy analysis of coriander (Coriadrum sativum L.) leaves drying in natural convection solar dryer

International Nuclear Information System (INIS)

Panwar, N.L.

2014-01-01

This study deals with thin layer drying characteristics of Coriandrum sativum L. leaves in a natural convection solar dryer. The Coriandrum sativum L. leaves were dried from a moisture content of 88% (w.b.) to 4.5% (w.b.) in 7.5 hours. The obtained drying data were fitted to eight different drying kinetics models. Of these, the model suggested by Midilli et al. [20] had the best fit with the drying behavior of Coriandrum sativum L. leaves. In addition, the thermodynamic behaviour of a solar dryer was evaluated. The energy efficiency during the study varied from 7.81 to 37.93%. The exergy efficiency of the drying process ranged between 55.35 and 79.39%. (author)

Design of mixed-mode natural convection solar crop dryers: Application of principles and rules of thumb

Energy Technology Data Exchange (ETDEWEB)

Forson, F.K.; Akuffo, F.O. [Department of Mechanical Engineering, Kwame Nkrumah University of Science and Technology, Kumasi (Ghana); Nazha, M.A.A.; Rajakaruna, H. [Department of Mechanical Engineering, De Montfort University, Queens Building, Leicester LE1 9BH (United Kingdom)

2007-11-15

A mixed-mode natural convection solar crop dryer (MNCSCD) designed and used for drying cassava and other crops in an enclosed structure is presented. A prototype of the dryer was constructed to specification and used in experimental drying tests. This paper outlines the systematic combination of the application of basic design concepts, and rules of thumb resulting from numerous and several years of experimental studies used and presents the results of calculations of the design parameters. A batch of cassava 160 kg by mass, having an initial moisture content of 67% wet basis from which 100 kg of water is required to be removed to have it dried to a desired moisture content of 17% wet basis, is used as the drying load in designing the dryer. A drying time of 30-36 h is assumed for the anticipated test location (Kumasi; 6.7 N,1.6 W) with an expected average solar irradiance of 400 W/m{sup 2} and ambient conditions of 25 C and 77.8% relative humidity. A minimum of 42.4 m{sup 2} of solar collection area, according to the design, is required for an expected drying efficiency of 12.5%. Under average ambient conditions of 28.2 C and 72.1% relative humidity with solar irradiance of 340.4 W/m{sup 2}, a drying time of 35.5 h was realised and the drying efficiency was evaluated as 12.3% when tested under full designed load signifying that the design procedure proposed is sufficiently reliable. (author)

Heat transfer to immersed horizontal tubes in gas fluidized bed dryers

Energy Technology Data Exchange (ETDEWEB)

Jonassen, Ola

1999-10-01

The main objective of this study was to construct heat pump fluidized bed dryers of the FHT type with improved dewatering capacity for a given size of the dryer. The use of heat exchangers immersed in the fluidized bed drying chambers is an important part of the FHT (Fluidized Bed High Temperature Heat Pump Dryer) concept. A pilot plant FHT dryer was built and successfully tested on fish meal raw material and seaweed. The plant included two fluidized bed drying chambers with immersed heat exchangers. The gain in water vapor of the drying air through the chambers was increased up to four times that of adiabatic drying. The energy saving concept was retained as a SMER ratio of 3.5 to 4.7 was measured in the same tests. Therefore optimization of the immersed heat exchangers was considered the most important single objective for this work. The optimization study of the heat exchangers was confined to the actual operating conditions for the dryers using: (1) Bubbling gas fluidized beds were used, (2) air as the only type of fluidising gas, (3) beds at atmospheric pressure, (4) bed temperatures below 100 {sup o}C, (5) fluidized particles of Geldart classes B and D, (6) horizontal tube banks for the immersed heat exchanger, and the influence of radiation heat transfer was ignored. The heat transfer study was confined to the fluidized bed side of the heat exchanger surface. It was concluded early in this work that the bubbles play a major role in generating the particle circulation inside the bed and hence also in heat transfer. Publications describing the most important bubble induced mechanisms contributing to high rates of heat transfer were found to be limited. Therefore the first part of this study was aimed at establishing a method for locating and measuring the size and rise velocity of bubbles inside the bed. The method established through this work using differential pressure measurements from two static pressure probes was used later in the study of heat transfer

Operational Augmentation of Forced Circulation Type Solar Dryer System Using CFD Analysis

OpenAIRE

Atul Patel; Gaurav Patel

2014-01-01

Solar drying is basically heat and mass transfer process in which the liquid water from the surface and the vapour removed by draft. The efficiency of a solar drying system is affected by the properties of drying materials.e.g. size, shape and geometry as well as ambient conditions. In this research article, the authors have done the CFD analysis of a Forced Circulation type Solar Dryer used conventionally for dehydrating vegetables and fruits. Using CFD analysis, the limiting...

Incorporation of occupational health and safety in cleaner production projects in South Africa

DEFF Research Database (Denmark)

Hedlund, Frank Huess

2002-01-01

The purpose of this research is to reveal ways in which occupational health and safety can be integrated in environmental cleaner production projects. Of particular interest are those cleaner production projects that are run by the Danish government's environmental assistance agency, Danced......, in South Africa.The study explores two main avenues of integration. First, integrating through better planning, focussing at the tools and procedures in use by Danced for project management -- integrating occupational health and safety into the project specification, so to speak.Second, integrating...... occupational health and safety into the environmental activities that take place at company level. Two ways of doing so are explored, the main distinction being company size. For large companies, integration of management systems may be attractive. For small companies, integration into a less formal network...

Upper-limit on the Advanced Virgo output mode cleaner cavity length noise

Science.gov (United States)

Bonnand, R.; Ducrot, M.; Gouaty, R.; Marion, F.; Masserot, A.; Mours, B.; Pacaud, E.; Rolland, L.; Was, M.

2017-09-01

The Advanced Virgo detector uses two monolithic optical cavities at its output port to suppress higher order modes and radio frequency sidebands from the carrier light used for gravitational wave detection. These two cavities in series form the output mode cleaner. We present a measured upper limit on the length noise of these cavities that is consistent with the thermo-refractive noise prediction of 8×10-16~m~Hz-1/2 at 15 Hz. The cavity length is controlled using Peltier cells and piezo-electric actuators to maintain resonance on the incoming light. A length lock precision of 3.5×10-13 m is achieved. These two results are combined to demonstrate that the broadband length noise of the output mode cleaner in the 10-60 Hz band is at least a factor 10 below other expected noise sources in the Advanced Virgo detector design configuration.

Using Pipe Cleaners to Bring the Tree of Life to Life

Science.gov (United States)

Halverson, Kristy L.

2010-01-01

Phylogenetic trees, such as the "Tree of Life," are commonly found in biology textbooks and are often used in teaching. Because students often struggle to understand these diagrams, I developed a simple, inexpensive classroom model. Made of pipe cleaners, it is easily manipulated to rotate branches, compare topologies, map complete lineages,…

Behavior of a portable solar dryer for pineapple fiber Comportamento de um secador solar para fibras de abacaxi

Directory of Open Access Journals (Sweden)

Róger Moya

2012-12-01

Full Text Available In Costa Rica, there has been a growing interest to use pineapple fiber from plant, for which current processes need to be improved or new processes need to be developed, with emphasis on drying methods. This work presents the design and evaluation of the behavior of a prototype portable solar dryer in four sites of Costa Rica. The design describes the main parts of the dryer, as well as how they were constructed. The behavior was evaluated according to temperature and relative humidity inside e outside the chamber, and the influence of direct and indirect solar radiation. In order to achieve improved dryer efficiency, a dehumidifier was used to control relative humidity, and a heating system was implemented during the hours of low temperature, low solar radiation and high relative humidity. Based on drying time, final moisture content of fibers of pineapple leaves from plant, and the varying hours when fibers were put to dry, the evaluation of the dryer revealed that the best fiber-drying interval is from 6h00 to 14h00, and after that, it is convenient to inject hot air and use a dehumidifier in the dryer in order to increase its efficiency.Na Costa Rica, o interesse pelo uso da fibra proveniente da folha de abacaxizeiro. Tem almentado e essa atividade precisa de melhoramento ou implementação de novos processos para alcançar maior eficiência, principalmente na secagem da fibra. O presente trabalho apresenta o design e comportamento de uma protótipo portátil de secadora solar em 4 sites geográficos da Costa Rica. Estão descritas as principais partes do secador, bem como a metodologia de construção. O comportamento foi avaliado de acordo com a temperatura e umidade relativa interna e externa da câmara e a influencia da radiação direta e indireta. Com a finalidade de melhorar a eficiência da secadora, foi usado um desumidificador para controlar a umidade relativa e ainda um sistema de aquecimento durante as horas de baixa temperatura

Evaluation of a fruit solar dryer; Avaliacao de um secador solar de frutas

Energy Technology Data Exchange (ETDEWEB)

Berthier, L.J.; Bittencourt, J.; Queiroz, M.R.

2000-07-01

A study of the Nanica banana drying was carried out in a solar dryer with six trays operating with direct exposure of the product to the solar radiation and internal convection. The solar drying was performed College of Agricultural Engineering of the UNICAMP, Campinas, S.Paulo state, Brazil. The study aimed a 20 to 25 per cent final humidity of the dry product, result obtained in the different trays during a maximum drying period of 147 hours (6 days), in a batch system. During the drying period, the average temperature of the environment air at daylight was of 26 degree Celsius with a maximum of 32 degree Celsius, and 18 degrees Celsius during nocturnal period, with a minimum of 12,6 degree Celsius. In the inward of the dryer reached average values near to 50 degree Celsius, measured at noon. The 29,540 kg initial net weight of peeled banana was reduced to yield of 10,815 kg after the drying process, obtaining an income of 36,61 percent of the total production. With the values of the product weight loss, the curves of the drying in each tray had been built, observing that, in the upper trays reached the desired humidity in a lesser period.

Aging and service wear of air compressors and dryers in nuclear power plants

International Nuclear Information System (INIS)

Moyers, J.C.

1989-01-01

Compressed air systems and their associated compressors and dryers as incorporated in LWR power plants usually are not classified as safety related systems and components because their continued operation is not required to bring the plant to a safe shutdown condition. However, control air is a vital requirement for maintaining stable plant operation and its loss often results in a reactor trip and, on occasion, the actuation of engineered safety feature systems. Concerns caused by repeated instances of failures in air systems resulted in the high-priority ranking of Generic Issue No. 43, ''Reliability of Air Systems'' by the NRC. In support of the Nuclear Plant Aging Research (NPAR) Program, the Oak Ridge National Laboratory is carrying out a Phase I aging assessment of air compressors and dryers used in LWR power plants. The objectives of this study include: (1) determination of the types and ratings of equipment utilized in typical plants; (2) identification of aging and service wear stressors imposed on the machines; (3) evaluation of operating experience with the machines; (4) comparison of user and manufacturer-recommended inspection, surveillance, and monitoring (ISM) methods; and (5) the identification of any improved ISM methods that might lead to longer, more reliable, service. 2 refs

Cleaner production analysis in a company of the red ceramic segment

Directory of Open Access Journals (Sweden)

Dayanna dos Santos Costa Maciel

2013-11-01

Full Text Available The present study had as objective to analyze the productive process of a red ceramic segment industry in relation to the Cleaner Production (CP, based on the theoretical model proposed by National Center of Clean Technologies (CTNL, 2003b. As for the methodology, is classified as exploratory and descriptive, using the case study method. For this purpose, data was collected primary and secondary, the primers were obtained through semi-structured interviews with the owner and manager of production and a questionnaire administered to the owner. As for the secondary data, they were obtained through the company's environmental license, reports, documents, audits, standards and web searches, among others. As results were found in a waste around 10% of manufactured products (bricks, tiles and blocks;  Emission of pollutants such as ash and gases (CO2; High consumption of natural resources such as clay, water, electricity and firewood. This situation is being modified in the function of actions which are taken to obtain a cleaner production.

Risk assessment of amorphous silicon dioxide nanoparticles in a glass cleaner formulation

Science.gov (United States)

Scheel, Julia; Karsten, Stefan; Stelter, Norbert; Wind, Thorsten

2013-01-01

Since nanomaterials are a heterogeneous group of substances used in various applications, risk assessment needs to be done on a case-by-case basis. Here the authors assess the risk (hazard and exposure) of a glass cleaner with synthetic amorphous silicon dioxide (SAS) nanoparticles during production and consumer use (spray application). As the colloidal material used is similar to previously investigated SAS, the hazard profile was considered to be comparable. Overall, SAS has a low toxicity. Worker exposure was analysed to be well controlled. The particle size distribution indicated that the aerosol droplets were in a size range not expected to reach the alveoli. Predictive modelling was used to approximate external exposure concentrations. Consumer and environmental exposure were estimated conservatively and were not of concern. It was concluded based on the available weight-of-evidence that the production and application of the glass cleaner is safe for humans and the environment under intended use conditions. PMID:22548260

Level of self-reported neck/shoulder pain and biomechanical workload in cleaners

DEFF Research Database (Denmark)

Madeleine, Pascal; Søgaard, Karen; Holtermann, Andreas

2012-01-01

The aim of the present study was to investigate the relation between self-reported pain, muscular activity and postural load during cleaning tasks. Eighteen cleaners performed usual cleaning tasks in both a laboratory and a lecture room. The level of perceived pain in the neck-shoulder region......-axial accelerometer package was mounted on the low back (L5-S1) to measure postural changes during cleaning tasks. The 10th, 50th and 90th percentiles of the angular distributions were computed to characterize postures and movements. Pain tended to play a significant role on RMS of left/right trapezius and left...... erector spinae muscles (P≤0.08). Cleaners with low pain level exhibited higher muscular activity during cleaning. Pain played or tended to play a significant role on PE of left and right erector spinae muscles (P≤0.08). Pain played a significant role on the 10th, 50th and 90th percentile (P...

Cleaner Coal in China [Chinese Version

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-07-01

China’s rapid economic growth has aroused intense interest around the world. Policy makers, industrialists, investors, environmentalists, researchers and others want to better understand the issues that this populous nation faces as it further develops an already thriving economy largely fuelled by coal. This study sheds light on the Chinese coal supply and transformation sectors. China’s rapid economic growth has aroused intense interest around the world. Policy makers, industrialists, investors, environmentalists, researchers and others want to better understand the issues that this populous nation faces as it further develops an already thriving economy largely fuelled by coal. This study sheds light on the Chinese coal supply and transformation sectors. China’s coal, mined locally and available at a relatively low cost, has brought enormous benefits to energy consumers in China and to those outside the country who enjoy the products of its coal-based economy. Yet from another perspective, China’s coal use has a high cost. Despite progress, health and safety in the thousands of small coal mines lag far behind the standards achieved in China’s modern, large mines. Environmental degradation is a real and pressing problem at all stages of coal production, supply and use. Adding to these burdens, emissions of carbon dioxide are of concern to the Chinese government as it embarks on its own climate protection strategy. Technology solutions are already transforming the way coal is used in China and elsewhere. This study explores the context in which the development and deployment of these technologies can be accelerated. Providing a large amount of new data, it describes in detail the situation in China as well as the experiences of other countries in making coal cleaner. Above all, the report calls for much greater levels of collaboration – existing bi-lateral and multi-lateral co-operation with China on coal is found lacking. China’s growing openness

Energy access and transition to cleaner cooking fuels and technologies in Sri Lanka: Issues and policy limitations

International Nuclear Information System (INIS)

Wickramasinghe, Anoja

2011-01-01

Easy energy access is a trigger for human, social, and economic development. A research project was undertaken in Sri Lanka to broaden the understanding of human dimension of energy access and technologies. A questionnaire survey, covering 2269 households, gathered data on socio-economic contexts and issues influencing a transition towards clean cooking facilities. The findings reveal that the transition is impeded by four factors: the lack of motivation and the pressure for switching over to cleaner facilities, the lack of modern energy technology options, the financial risks, and the lack of financing and other support. The paper describes the delicate two-way interrelation between women earning wages and the transitions to cleaner cooking fuels and technologies. The findings suggest the need for a policy framework involving the stakeholders, financing and standardised technologies. To make a change it is proposed to introduce a national, integrated policy incorporating financing and energy governance. - Highlights: ► Households in Sri Lanka lack access to modern energy technology options for cooking. ► Cooking with fuel wood and residues is the norm in Sri Lanka, particularly in rural households. ► A survey of rural households revealed that most cannot afford to switch to cleaner cooking options. ► Most households have little awareness of the health impacts of biomass cooking. ► Women in regular formal employment are more likely to value cleaner cooking options that save time.

The effects of crude oil and the effectiveness of cleaner application following oiling on US Gulf of Mexico coastal marsh plants.

Science.gov (United States)

Pezeshki, S R; DeLaune, R D; Jugsujinda, A

2001-01-01

Field studies were conducted in two different marsh habitats in Louisiana coastal wetlands to evaluate the effects of oiling (using South Louisiana Crude oil, SLC) and the effectiveness of a shoreline cleaner (COREXIT 9580) in removing oil from plant canopies. The study sites represented two major marsh habitats; the brackish marsh site was covered by Spartina patens and the freshwater marsh was covered by Sagittaria lancifolia. Field studies were conducted in each habitat using replicated 5.8 m2 plots that were subjected to three treatments; oiled only, oiled + cleaner (cleaner was used 2 days after oiling), and a control. Plant gas exchange responses, survival, growth, and biomass accumulation were measured. Results indicated that oiling led to rapid reductions in leaf gas exchange rates in both species. However, both species in 'oiled + cleaned' plots displayed improved leaf conductance and CO2 fixation rates. Twelve weeks after treatment initiation, photosynthetic carbon fixation in both species had recovered to normal levels. Over the short-term, S. patens showed more sensitivity to oiling with SLC than S. lancifolia as was evident from the data of the number of live shoots and above-ground biomass. Above-ground biomass remained significantly lower than control in S. patens under 'oiled' and 'oiled + cleaned' treatments while it was comparable to controls in S. lancifolia. These studies indicated that the cleaner removed oil from marsh grasses and alleviated the short-term impact of oil on gas exchange function of the study plants. However, use of cleaner had no detectable effects on above-ground biomass production or regeneration at the end of the first growing season in S. patens. Similarly, no beneficial effects of cleaner on carbon fixation and number of live shoots were apparent beyond 12 weeks in S. lancifolia.

Effects of 12 months aerobic exercise intervention on work ability, need for recovery, productivity and rating of exertion among cleaners

DEFF Research Database (Denmark)

Lidegaard, Mark; Søgaard, Karen; Krustrup, Peter

2018-01-01

PURPOSE: This study assessed the effects of a worksite aerobic exercise intervention among cleaners on: work ability, need for recovery, productivity, and rating of exertion. METHODS: In a monocentric randomised controlled trial in Denmark, 116, of 250 invited, cleaners were cluster-randomised (w......PURPOSE: This study assessed the effects of a worksite aerobic exercise intervention among cleaners on: work ability, need for recovery, productivity, and rating of exertion. METHODS: In a monocentric randomised controlled trial in Denmark, 116, of 250 invited, cleaners were cluster......-randomised (work location; sex; age; length of service) to aerobic exercise [N = 57, 44.9 years, 75.4% female, body mass index (BMI) 26.2], receiving 2 weekly aerobic exercise sessions during 12 months, or a reference group (N = 59, 45.7 years, 76.3% female, BMI 27.1), receiving health-promoting lectures. Self.......2) in the aerobic exercise group compared to the reference group. Productivity and rating of exertion were unaltered. Analysis stratified on age showed significant effects only among the participants aged ≤ 45 years. CONCLUSIONS: After 12 months work ability improved and need for recovery decreased. A period of 4...

Performance of A Horizontal Cylinder Type Rotary Dryer for Drying Process ofOrganic Compost from Solid Waste Cocoa Pod

Directory of Open Access Journals (Sweden)

Sukrisno Widyotomo

2008-07-01

Full Text Available Cocoa pod husk is the bigest component of cocoa pod, about 70% of total ht of mature pod, and to potentially used as organic compost source. Poten tial solid waste of cocoa pod husk from a cocoa processing centre is about 15— 22 m3/ha/year. A cocoa plantation needs about 20—30 ton/ha/year of organic matters. One of important steps in compos processing technology of cocoa pod solid waste is drying process. Organic compost with 20% moisture content is more easy in handling, application, storage and distribution. Indonesian Coffee and Cocoa Research Institute has designed and tested a horizontal cylinder type rotary dryer for drying process of organic compos from solid waste cocoa pod with kerosene burner as energy sources. The objective of this research is to study performance of a horizontal cylinder type rotary dryer using kerosene burner as energy source for drying process of organic compost from solid waste cocoa pod. The material used was solid waste cocoa pod with 70—75% moisture content (wet basis, 70% size particle larger than 4.76 mm, and 30% size particle less than 4.76 mm, 690—695 kg/m3 bulk density. Drying process temperatures treatment were 60OC, 80OC, and 100OC, and cylinder rotary speed treatments were 7 rpm, 10 rpm, dan 16 rpm. The results showed that dryer had capacity about 102—150 kg/h depend on drying temperature and cylinder rotary speed. Optimum operation condition at 100OC drying temperature, and 10 rpm cylinder rotary speed with drying time to reach final moisture content of 20% was 1,6 h, capacity 136,14 kg/ h, bulk density 410 kg/m3, porocity 45,15%, kerosene consumption as energy source was 2,57 l/h, and drying efficiency 68,34%. Key words : cocoa, drying, rotary dryer, compost, waste

Temperature Control System for Mushroom Dryer

Science.gov (United States)

Wibowo, I. A.; Indah, Nur; Sebayang, D.; Adam, N. H.

2018-03-01

The main problem in mushroom cultivation is the handling after the harvest. Drying is one technique to preserve the mushrooms. Traditionally, mushrooms are dried by sunshine which depends on the weather. This affects the quality of the dried mushrooms. Therefore, this paper proposes a system to provide an artificial drying for mushrooms in order to maintain their quality. The objective of the system is to control the mushroom drying process to be faster compared to the natural drying at an accurate and right temperature. A model of the mushroom dryer has been designed, built, and tested. The system comprises a chamber, heater, blower, temperature sensor and electronic control circuit. A microcontroller is used as the controller which is programmed to implement a bang-bang control that regulates the temperature of the chamber. A desired temperature is inputted as a set point of the control system. Temperature of 45 °C is chosen as the operational drying temperature. Several tests have been carried out to examine the performance of the system including drying speed, the effects of ambient conditions, and the effects of mushroom size. The results show that the system can satisfy the objective.

Cleaner Technology in the Hard Disk Drive Manufacturing Industry: A Case Study

Science.gov (United States)

Moolla, Premchai; Chompu-inwai, Rungchat

2010-10-01

The objectives of this research are to improve raw material and energy consumption efficiency, as well as reduce defects and the use of chemicals in the arm coil assembly process of hard disk drive manufacturing in the case study company by applying the Cleaner Technology concepts. The four main sequential steps used in this research were: (1) pre-assessment, (2) assessment, (3) feasibility study, and (4) implementation. In the first step, raw data, such as process flows, raw material usage and defects data were collected. In the second step, the loss during production and causes of loss were analyzed. Opportunities to reduce raw material, chemical and energy wastage could then be recommended. The next step was to evaluate the feasibility and potential benefits of a particular Cleaner Technology opportunity. Finally, in the last step, after a thorough evaluation and implementation of the opportunities to apply Cleaner Technology, the results showed that arm coil defects could be reduced by improving the production process using the ECRS technique. ECRS stands for Eliminate, Combine, Rearrange and Simplify. This improvement reduced arm coil defect rates from 0.48% to 0.15%, thus saving approximately 139,638 Thai Baht per month. In addition, production stoppage decision made by workers was used to increase employee involvement in defect detection. Allowing workers to participate in such a decision was an effective way to reduce defect rate and could motivate workers to produce a better quality job. This resulted in arm coil defects reducing from 0.41% to 0.025%, with about 74,562 Thai Baht per month saving. Additionally, an increase in the efficiency of electricity consumption occurred, by increasing the speed of the infrared oven conveyor belt, improving average productivity from 533 pieces/hour to 560 pieces/hour, without adversely affecting product costs and quality, thus producing products of up to the value of 206,242 Thai Baht per month. Furthermore, the new

Measurement of flow inside a vacuum cleaner head

Science.gov (United States)

Iguchi, Ryotaro; Ban, Hisataka; Sakakibara, Jun

2017-11-01

Vacuum cleaner head with rotating brushes is widely used as a home appliance. Although it efficiently collects dusts from the floor, flow field of the air and motion of the dust inside the head have not been fully investigated. In this study, we performed 3D-PIV (particle tracking velocimetry) measurement of velocity field inside the head. Water was used as working fluid, which allows a use of fluorescent particle to reduce unwanted reflection from the brushes and inner surface of the head. Mean velocity field and turbulence statistics in the head with and without the brush will be presented.

75 FR 37593 - Energy Conservation Program for Consumer Products: Test Procedures for Clothes Dryers and Room...

Science.gov (United States)

2010-06-29

... docket number EERE-2008-BT-TP-0010 and/or RIN 1904-AC02 in the subject line of the message. 3. Mail: Ms... DOE clothes washer test procedure), which is assumed to proportionally impact dryer load sizes. DOE... noted that IEC Standard 62087 specifies methods of measuring the power consumption of TV receivers...

Sudden death involving inhalation of 1,1-difluoroethane (HFC-152a) with spray cleaner: three case reports.

Science.gov (United States)

Sakai, Kentaro; Maruyama-Maebashi, Kyoko; Takatsu, Akihiro; Fukui, Kenji; Nagai, Tomonori; Aoyagi, Miwako; Ochiai, Eriko; Iwadate, Kimiharu

2011-03-20

Spray cleaner is a cleaning product containing compressed 1,1-difluoroethane (HFC-152a) to blow dust off electric devices and other sensitive equipment; however, it is also inhaled to induce euphoria. This report describes three cases of death involving HFC-152a inhalation with spray cleaner under different circumstances. In case 1, death was during inhalation for euphoria with which led to having frostbite. In case 2, death may have been associated with suicidal intention. Case 3 was also considered an accidental autoerotic death. In all three cases, HFC-152a was detected at 99.2-136.2mg/l in blood samples, 94.5-191.9 mg/l in urine samples and 3.6-18.4 mg in the gastric contents according to gas chromatography with flame ionization detection. To prevent death associated with HFC-152a inhalation from spray cleaner, the danger of the sudden death should be announced to people, given the ready availability of commercial products containing HFC-152a. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

Evaluating The Operation Of Three Air Cleaners Working Individually In A Clean Room

DEFF Research Database (Denmark)

Ardkapan, Siamak Rahimi; Afshari, Alireza; Bergsøe, Niels Christian

2011-01-01

The use of portable air cleaners is becoming increasingly popular in many countries including Denmark. Portable air cleaners are known for not only removing but also generating particles and gases. To clarify this, three air cleaning technologies were evaluated. They were nonthermal plasma......, photochemical air purifier and corona discharge ionizer. The concentrations of ultrafine particles, ozone and total volatile organic compounds were measured both in a duct and in a clean room. It was found that the studied air cleaning technologies increased the ozone level in the clean room and the duct....... The increase of ozone level in the clean room was more than that was measured in the duct. Additionally, it was found that the number of ultrafine particles in the room increased due to the generated ozone. The number of generated particles changed with the season. The study leads to the recommendation...

Analysis of the potentiality for implementing of the cleaner production and adopting a sustainable consumption in the Cuban entrepreneurial system

International Nuclear Information System (INIS)

Tortosa Ferrer, Barbara Ivette; Orue Valdes, Sonia; Mena Ulecia, Karel

2007-01-01

The world economic development has conduced to increase the worsening of the environment as result of the natural resources pollution. The tendency has been toward the unsustainable exploitation of natural resources, to increasing of the goods and services production, as well as, to elevated consumption. In this sense, many countries have planed environmental policies addressed to reducing of pollution introducing cleaner production practices and promoting the adoption of responsible consumption. This article shows the existing potentiality in a selected Cuban companies group for introducing and applying of the cleaner production, as well as, the adoption of a sustainable consumption start from analysis of the obtained results in short-term assessments (quick scans) carried out by the Cuban Environment Agency Focal Point of the National Cleaner Production Network in the period between 2004 and 2007

Heat transfer to immersed horizontal tubes in gas fluidized bed dryers

Energy Technology Data Exchange (ETDEWEB)

Jonassen, Ola

1999-07-01

The main objective of this study was to construct heat pump fluidized bed dryers of the FHT type with improved dewatering capacity for a given size of the dryer. The use of heat exchangers immersed in the fluidized bed drying chambers is an important part of the FHT (Fluidized Bed High Temperature Heat Pump Dryer) concept. A pilot plant FHT dryer was built and successfully tested on fish meal raw material and seaweed. The plant included two fluidized bed drying chambers with immersed heat exchangers. The gain in water vapor of the drying air through the chambers was increased up to four times that of adiabatic drying. The energy saving concept was retained as a SMER ratio of 3.5 to 4.7 was measured in the same tests. Therefore optimization of the immersed heat exchangers was considered the most important single objective for this work. The optimization study of the heat exchangers was confined to the actual operating conditions for the dryers using: (1) Bubbling gas fluidized beds were used, (2) air as the only type of fluidizing gas,(3) beds at atmospheric pressure, (4) bed temperatures below 100 {sup o}C, (5) fluidized particles of Geldart classes B and D, (6) horizontal tube banks for the immersed heat exchanger and the influence of radiation heat transfer was ignored. The heat transfer study was confined to the fluidized bed side of the heat exchanger surface. It was concluded early in this work that the bubbles play a major role in generating the particle circulation inside the bed and hence also in heat transfer. Publications describing the most important bubble induced mechanisms contributing to high rates of heat transfer were found to be limited. Therefore the first part of this study was aimed at establishing a method for locating and measuring the size and rise velocity of bubbles inside the bed. The method established through this work using differential pressure measurements from two static pressure probes was used later in the study of heat transfer

Aeroacoustic characteristics and noise reduction of a centrifugal fan for a vacuum cleaner

Energy Technology Data Exchange (ETDEWEB)

Jeon, Wan Ho; Rew, Ho Seon; Kim, Chang Joon [LG Electronics, Seoul (Korea, Republic of)

2004-02-01

The aeroacoustic characteristics of a centrifugal fan for a vacuum cleaner and its noise reduction method are studied in this paper. The major noise source of a vacuum cleaner is the centrifugal fan. The impeller of the fan rotates at over 30000 rpm, and generates very high-level noise. It was revealed that the dominant noise source is the aerodynamic interaction between the rotating impeller and stationary diffuser. The directivity of acoustic pressure showed that most of the noise propagates backward direction of the fan-motor assembly. In order to reduce the high tonal sound generated from the aerodynamic interaction, unevenly pitched impeller and diffuser, and tapered impeller designs were proposed and experiments were performed. Uneven pitch design of the impeller changes the sound quality while the overall Sound Power Level (SPL) and the performance remains similar. The effect of the tapered design of impeller was evaluated. The trailing edge of the tapered fan is inclined. This reduces the flow interaction between the rotating impeller and the stationary diffuser because of some phase shifts. The static efficiency of the new impeller design is slightly lower than the previous design. However, the overall SPL is reduced by about 4 dB(A). The SPL of the fundamental Blade Passing Frequency (BPF) is reduced by about 6 dB(A) and the 2{sup nd} BPF is reduced about 20 dB(A). The vacuum cleaner with the tapered impeller design produces lower noise level than the previous one, and the strong tonal sound was dramatically reduced.

Aeroacoustic characteristics and noise reduction of a centrifugal fan for a vacuum cleaner

International Nuclear Information System (INIS)

Jeon, Wan Ho; Rew, Ho Seon; Kim, Chang Joon

2004-01-01

The aeroacoustic characteristics of a centrifugal fan for a vacuum cleaner and its noise reduction method are studied in this paper. The major noise source of a vacuum cleaner is the centrifugal fan. The impeller of the fan rotates at over 30000 rpm, and generates very high-level noise. It was revealed that the dominant noise source is the aerodynamic interaction between the rotating impeller and stationary diffuser. The directivity of acoustic pressure showed that most of the noise propagates backward direction of the fan-motor assembly. In order to reduce the high tonal sound generated from the aerodynamic interaction, unevenly pitched impeller and diffuser, and tapered impeller designs were proposed and experiments were performed. Uneven pitch design of the impeller changes the sound quality while the overall Sound Power Level (SPL) and the performance remains similar. The effect of the tapered design of impeller was evaluated. The trailing edge of the tapered fan is inclined. This reduces the flow interaction between the rotating impeller and the stationary diffuser because of some phase shifts. The static efficiency of the new impeller design is slightly lower than the previous design. However, the overall SPL is reduced by about 4 dB(A). The SPL of the fundamental Blade Passing Frequency (BPF) is reduced by about 6 dB(A) and the 2 nd BPF is reduced about 20 dB(A). The vacuum cleaner with the tapered impeller design produces lower noise level than the previous one, and the strong tonal sound was dramatically reduced

Energy aAnalysis and Kinetics of Mint Leaves Dehydration Using Vibro-Fluidized Bed Heat Pump Dryer

Directory of Open Access Journals (Sweden)

S. M Ataei Ardestani

2015-03-01

Full Text Available Fluidized bed dryers have not yet been used for drying products such as mint leaves. This could be due to high porosity and low mechanical resistance resulting in poor quality of fluidization. Applying vibration has been recommended to overcome problems such as channeling and defluidization, and hence improving the fluidization quality. In this research, a laboratory scale vibro-fluidized bed heat pump dryer was designed and constructed for drying mint leaves. The experiments were conducted at vibration frequency of 80 Hz and amplitude of 3 mm. The velocity and temperature of the inlet air was controlled by an automatic control system. Experiments were carried out at 40, 50 and 60 °C, and two methods: heat pump drying (HPD and non-heat pump drying (NHPD. The results revealed that drying process primarily occurred in the falling rate period. Effective moisture diffusivity of the samples increased with increase in drying air temperature and varied from 4.26656×10-11 to 2.95872×10-10 m2 s-1 for the HPD method, and 3.71918×10-11 to 1.29196×10-10 m2 s-1 for the NHPD method and was within the reported range of 10-9 to 10-11 m2 s-1 for drying of food materials. The activation energy was determined to be 84 kJ mol-1 for the HPD and 54.34 kJ mol-1 for the NHPD, both have very good agreement with the results of other investigators. The coefficient of performance and specific moisture evaporation rate showed the acceptable performance of the heat pump system. Moreover, the energy consumption of the dryer for the NHPD method was more than the HPD method.

Evolution of thermo-physical properties of Akuama (picralima nitida) seed and antioxidants retention capacity during hot air drying

Science.gov (United States)

Ndukwu, M. C.; Bennamoun, L.; Anozie, O.

2018-05-01

Interest in picralima nitida is growing over the years because of its therapeutic application in human and animal medicine. In many countries the dried seed is compounded and sold as drugs but there is limited information on the process variables associated with its thermal processing. The study therefore, is focused on the evolution of physical properties, heat and mass transfer coefficient, specific heat capacity, energy utilization and quality characteristics of the seed during oven and microwave drying. The goal is to generate data using theoretical and empirical steps for process model development that can be applied in dryer design. The results obtained showed that the coefficient of heat and mass transfer varied from 0.0421-1.326 W/m2 K and 1.49 × 10-7 - 8.47 × 10-6 m/s respectively while the specific heat capacity ranged between 1189 and 2531 J/ kg K. The volume of the seed shrank gradually with a non-linear exponential shape for all drying treatments. The intrinsic particle and bulk densities decreased while the porosity of the seed increased with drying period, indicating an increase in internal voids of the seeds. The energy and specific energy utilized for drying peaked after 14 h, 12 h and 7 h of continuous drying at 50, 60 and 70 °C for oven drying treatment. Effective moisture diffusivities for all treatments ranged from 5.37 × 10-10 - 1.45 × 10-7 m/s2 with activation energy of 27.82 kJ/mol and 20 W/g for oven and microwave respectively. Flavonoide was the least stable at high temperature among the screend compound.

Drying of mint leaves in a solar dryer and under open sun: Modelling, performance analyses

International Nuclear Information System (INIS)

Akpinar, E. Kavak

2010-01-01

In this study was investigated the thin-layer drying characteristics in solar dryer with forced convection and under open sun with natural convection of mint leaves, and, performed energy analysis and exergy analysis of solar drying process of mint leaves. An indirect forced convection solar dryer consisting of a solar air collector and drying cabinet was used in the experiments. The drying data were fitted to ten the different mathematical models. Among the models, Wang and Singh model for the forced solar drying and the natural sun drying were found to best explain thin-layer drying behaviour of mint leaves. Using the first law of thermodynamics, the energy analysis throughout solar drying process was estimated. However, exergy analysis during solar drying process was determined by applying the second law of thermodynamics. Energy utilization ratio (EUR) values of drying cabinet varied in the ranges between 7.826% and 46.285%. The values of exergetic efficiency were found to be in the range of 34.760-87.717%. The values of improvement potential varied between 0 and 0.017 kJ s -1 . Energy utilization ratio and improvement potential decreased with increasing drying time and ambient temperature while exergetic efficiency increased.

Effects of Friction Reduction on Fiber Damage in a Saw-Type Lint Cleaner

Science.gov (United States)

U.S. cotton is at a competitive disadvantage from a fiber-quality standpoint, because lint cleaning is required for mechanically harvested cotton, and lint cleaning causes fiber damage. Lint-cleaning research has focused mainly on modifying saw-type lint cleaners, but the work reported here focuses...

Too tired for exercise? The work and leisure of female cleaners in Denmark

DEFF Research Database (Denmark)

Lenneis, Verena; Pfister, Gertrud Ursula

2017-01-01

on the relevant literature on women’s work–life balance and (migrant) women’s participation in LTPA, we approached their work and leisure from an intersectionality perspective and explored if and how female cleaners engaged in LTPA and which constraints impeded their involvement. The interviewees’ narratives...

Workshop on Indian Chemical Industry: perspectives on safety, cleaner production and environment production

NARCIS (Netherlands)

Ham, J.M.

1996-01-01

A Workshop on "Indian Chemical Industry: Perspectives on Safety, Cleaner Production and Environmental Protection" was held on 3, 4 and 5 January 1996, in Bombay, India. The main objective of the workshop, which was organised jointly by the Government of India, UNIDO/UNDP and the Indian Chemical

Playing after work? Opportunities and challenges of a physical activity programme for female cleaners

DEFF Research Database (Denmark)

Lenneis, Verena; Pfister, Gertrud Ursula

2016-01-01

The workplace is regarded as an ideal setting for health promotion, not least because large sections of the population, including “high risk groups”, can be reached. One group which is reportedly in great demand of health promotion is that of female (migrant) cleaners – the participants in our...... factors constrained and which supported participation. The interviews revealed a high degree of appreciation for the training but also pointed to a number of constraints which were embedded into the participants’ biographies and everyday lives as migrant cleaners in Denmark. Most women had no previous...... experience with sport and exercise and struggled with the high demands at work and a “second shift” at home. As a consequence, most participants found the training too time- and energy-consuming. We conclude that exercise programmes should preferably be conducted at the workplace and during working hours....

Transition to an intelligent use of cleaner biomass stoves

DEFF Research Database (Denmark)

Luis Teles de Carvalho, Ricardo; Jensen, Ole Michael; Vicent, Estela D.

2016-01-01

are relevant issues to save energy and avoid greenhouse gas (CO2e) emissions. This work compares the operating performance of 3 types of biomass stoves used in Europe in their interaction with dwellings. Field studies were conducted in 24 houses in Portugal and Denmark to analyse wood-burning behaviours......In Europe, inappropriate user behaviours in the operation of wood-burning stoves (WBSs) results in substantial energy losses where fireplaces and conventional stoves are major contributors to undue emissions of health damaging fine particulate matter (PM2.5). The design and adoption of cleaner WBSs...

Extremely Low Frequency (ELF) Vertical Electric Field Exposure of Rats: Irradiation Facility

Science.gov (United States)

1977-05-01

altered inside an animal cage even with wet or dry litter and full food and water containers. Rats weighing approximately 300 g in adjacent cages caused...with guard circuit Field inside empty cage Field inside complete cage ( litter (wet or dry) + food + water) Field variations caused by 300 g rat...blanket 250 Iron 60 Broiler 130 Hair dryer 40 Vaporizer 40 Refrigerator 60 Color TV 30 Stereo 90 Coffee pot 30 Vacuum cleaner 16 Clock radio

Field evaluation and health assessment of air cleaners in removing radon decay products in domestic environments

International Nuclear Information System (INIS)

Li, Chih-Shan.

1990-01-01

In this study, field evaluations of two types of air cleaners were conducted in three single-family houses. The measurements included radon concentration, particle number concentration, and concentration and size distribution of radon decay products. The influence on the behavior of radon decay products by various indoor particles both with and without the air cleaning systems was investigated. A room model was used to calculate the changes in the aerosol parameters caused by the operation of the air cleaners. Using the James dosimetric models (1989 and 1990), the changes in the hourly bronchial dose rate per Bq m -3 radon for men, women, and children can be estimated for various domestic environments. 94 refs., 60 figs., 28 tabs

Modeling 3D conjugate heat and mass transfer for turbulent air drying of Chilean papaya in a direct contact dryer

Science.gov (United States)

Lemus-Mondaca, Roberto A.; Vega-Gálvez, Antonio; Zambra, Carlos E.; Moraga, Nelson O.

2017-01-01

A 3D model considering heat and mass transfer for food dehydration inside a direct contact dryer is studied. The k- ɛ model is used to describe turbulent air flow. The samples thermophysical properties as density, specific heat, and thermal conductivity are assumed to vary non-linearly with temperature. FVM, SIMPLE algorithm based on a FORTRAN code are used. Results unsteady velocity, temperature, moisture, kinetic energy and dissipation rate for the air flow are presented, whilst temperature and moisture values for the food also are presented. The validation procedure includes a comparison with experimental and numerical temperature and moisture content results obtained from experimental data, reaching a deviation 7-10 %. In addition, this turbulent k- ɛ model provided a better understanding of the transport phenomenon inside the dryer and sample.

Acute effect on ambulatory blood pressure from aerobic exercise: a randomised cross-over study among female cleaners.

Science.gov (United States)

Lund Rasmussen, Charlotte; Nielsen, Line; Linander Henriksen, Marie; Søgaard, Karen; Krustrup, Peter; Holtermann, Andreas; Korshøj, Mette

2018-02-01

High occupational physical activity (OPA) is shown to increase the risk for elevated blood pressure, cardiovascular diseases and mortality. Conversely, aerobic exercise acutely lowers the blood pressure up to 25 h post exercise. However, it is unknown if this beneficial effect also apply for workers exposed to high levels of OPA. Cleaners constitute a relevant occupational group for this investigation because of a high prevalence of OPA and cardiovascular disease. Accordingly, the objective was to investigate the acute effects on ambulatory blood pressure from a single aerobic exercise session among female cleaners. Twenty-two female cleaners were randomised to a cross-over study with a reference and an aerobic exercise session. Differences in 24-h, work hours, leisure time, and sleep ambulatory blood pressure (ABP) were evaluated using repeated measure 2 × 2 mixed-models. After the aerobic exercise session, the 24-h systolic ambulatory blood pressure was significantly lowered by 2.4 mmHg (p ABP was unaltered. During work hours, a lowered systolic ABP of 2.2 mmHg (p = 0.02) and a higher diastolic ABP of 1.5 mmHg (p = 0.03) were found after the aerobic exercise session. During leisure time, the systolic ABP was lowered by 1.7 mmHg (p = 0.04) and the diastolic ABP was unaltered. During sleep, the systolic and diastolic ABP was unaltered. A single aerobic exercise session lowered 24-h systolic ABP of 2.4 mmHg. Thus, an aerobic exercise session seems to be beneficial for lowering the risk of hypertension among cleaners.

Applying real options analysis to assess cleaner energy development strategies

International Nuclear Information System (INIS)

Cheng, Ching-Tsung; Lo, Shang-Lien; Lin, Tyrone T.

2011-01-01

The energy industry, accounts for the largest portion of CO 2 emissions, is facing the issue of compliance with the national clean energy policy. The methodology for evaluating the energy mix policy is crucial because of the characteristics of lead time embedded with the power generation facilities investment and the uncertainty of future electricity demand. In this paper, a modified binomial model based on sequential compound options, which may account for the lead time and uncertainty as a whole is established, and a numerical example on evaluating the optional strategies and the strategic value of the cleaner energy policy is also presented. It is found that the optimal decision at some nodes in the binomial tree is path dependent, which is different from the standard sequential compound option model with lead time or time lag concept. The proposed modified binomial sequential compound real options model can be generalized and extensively applied to solve the general decision problems that deal with the long lead time of many government policies as well as capital intensive investments. - Highlights: → Introducing a flexible strategic management approach for government policy making. → Developing a modified binomial real options model based on sequential compound options. → Proposing an innovative model for managing the long term policy with lead time. → Applying to evaluate the options of various scenarios of cleaner energy strategies.

Sustainable implementation of solar tunnel dryers, water heaters and cookers in Nepal

Energy Technology Data Exchange (ETDEWEB)

Kovacs, Peter [Danish Energy Management, DEM for Renewable Energy Project, REP, Dhobighat, Lalitpur (Nepal); Shrestha, Niraj; Shakya, Prajwal Raj [Renewable Energy Project, REP, Dhobighat, Lalitpur (Nepal); Pokharel, Govind [Alternative Energy Promotion Centre (AEPC), Lalitpur (Nepal)

2008-07-01

The Renewable Energy Project (REP) is a joint effort of the European Union and the Government of Nepal. Main objectives of the project are to create renewable energy infrastructure and services for the benefit of rural people in remote districts of Nepal. The REP will provide solar energy systems for public services in remote districts, as well as for income generating activities e.g. agro business and tourism. The REP focuses on the installation of institutional PV systems with a total capacity of 0.850 MWp. Concurrently, a number of solar thermal systems are being provided to community organizations (COs) in rural areas of Nepal. The priority applications for the solar thermal part are solar tunnel dryers for small industries drying vegetables. fruits and herbs, solar water heaters for community centers in trekking areas and large scale solar cookers in schools. The paper describes the Renewable Energy Project's implementation program for solar thermal technology and in particular the implications on design and usefulness of the solar tunnel dryer from on-site feasibility studies carried out by the project team. REP provides a framework for a sustainable implementation of these systems by carrying out the whole process from dissemination of information to demand collection, feasibility studies, design, procurement, commissioning and user training. Hand over of ownership will take place once the equipment is installed and successfully commissioned. Monitoring during the first year of operation should conclude the project. REP is co-funded by the European Union and the Government of Nepal. (orig.)

Design, Construction and Testing of Simple Solar Maize Dryer

Directory of Open Access Journals (Sweden)

Joshua FOLARANMI

2008-12-01

Full Text Available This project reports the design, construction and testing of a simple solar maize dryer. It is design in such a way that solar radiation is not incident directly on the maize, but preheated air warmed during its flow through a low pressure thermosphonic solar energy air heater or collector made up of an insulating material (polystyrene of size 100mmx50mmx25.4mm, absorber plate (aluminium sheet painted black of size 100mmx50mm and a cover glass (5mm thickness measuring 100mmx50mm all arranged in this order contributed to the heating. The test results gave temperature above 45OC in the drying chamber, and the moisture content of 50kg of maize reduced to about 12.5% in three days of 9hours each day of drying.

Drying characteristics of garlic ( Allium sativum L) slices in a convective hot air dryer

Science.gov (United States)

Demiray, Engin; Tulek, Yahya

2014-06-01

The effects of drying temperatures on the drying kinetics of garlic slices were investigated using a cabinet-type dryer. The experimental drying data were fitted best to the Page and Modified Page models apart from other theoretical models to predict the drying kinetics. The effective moisture diffusivities varied from 4.214 × 10-10 to 2.221 × 10-10 m2 s-1 over the temperature range studied, and activation energy was 30.582 kJ mol-1.

Drying of Ceramic Hollow Bricks in an Industrial Tunnel Dryer: A Finite Volume Analysis

OpenAIRE

F Tavares; S Neto; E Barbosa; A Lima; C Silva

2016-01-01

This paper aims to study the drying of industrial hollow bricks in a tunnel dryer cross flow type. The theoretical model is based on mass and energy conservation equations applied to air and product. To validate the methodology, numerical and experimental results for the moisture content and the temperature of brick during the drying in an industrial scale are compared and a good correlation was obtained. Results of moisture content and temperature of the product, and temperature, relative hu...

Seed quality in informal seed systems

NARCIS (Netherlands)

Biemond, P.C.

2013-01-01

Keywords: informal seed systems, seed recycling, seed quality, germination, seed pathology, seed health, seed-borne diseases, mycotoxigenic fungi, Fusarium verticillioides, mycotoxins, Vigna unguiculata, Zea mays, Nigeria.

Seed is a crucial input for agricultural production.

Investigation of influence of drying agent movement on the drying process effectiveness in the gravitational shelf dryer

Directory of Open Access Journals (Sweden)

N. O. Artyukhova

2017-12-01

Full Text Available The article stands for a research of the drying process efficiency of various approaches of reciprocal movement organization of drying agent and disperse material. It focuses on the results of shelf dryer investigation. The test condition was as follows: backflow of the drying agent and disperse material movement; backflow of the drying agent and disperse material movement with the drying agent recirculation; backflow of the drying agent and disperse material movement with the bypassing of drying agent and it’s putting on separate stage of gravitational shelf dryer. The influence of the drying agent movement organization on the characteristics of disperse material and drying agent, energy costs for this process and its efficiency is shown. The recommendations of usage of represented approaches of flows movement organization depending on the desired final moisture of the material as well as its physical and chemical properties are given. The proposed ways of reciprocal flows movement organization allow to reduce the costs of drying agent heating or to increase the efficiency of moisture removal at constant energy consumption.

KAJIAN TEKNIS-EKONOMIS ALAT PENGERING PATI SAGU MODEL CROSS FLOW VIBRO FLUIDIZED BED (Study on Technical-Economic of Sago Starch Dryer Model of Cross Flow Vibro Fluidized Bed

Directory of Open Access Journals (Sweden)

Abadi Jading

2015-02-01

Full Text Available The purpose of this research was to evaluate performance of vibro cross flow fluidized bed dryer using biomass fuel for drying sago starch. The phase of research were evaluation of dryer heated by a biomass stove using coconut shell as a fuel and observation of the drying temperature, moisture content, drying time, energy analysis, and drying effiviency, as well as calculation of its economic analysis. The dryer has dimension of 200x50x1500 cm for length, width, hight, respectively, and working capacity of 35kg/process. The results showed that biomass fuel consumption for drying sago starch for 7 hours was 12740,00 MJ (70 kg/process and electricity consumption for blower and vibrator was 37,80 MJ. Furthermore, the dryer reduced moisture content of sago starch from 42% (wb to 12% (wb with temperature in the vibrator chamber of 40-60 oC and relative humidity of 50%, as well as ambient temperature of 30 3C and drying efficiency of 46,02%. Economic analysis showed that the dryer had NPV of Rp. 16.002.858, BCR of 1,53, IRR of 35%, and PBP of 3,51 years. Keywords: Cross flow, vibro fluidized bed dryer, biomass stoves, sago starch, financial analysis   ABSTRAK Tujuan penelitian ini adalah melakukan pengujian terhadap alat pengering pati berbasis sagu model cross flow vibrofluidized bed bertenaga biomassa. Tahapan penelitian meliputi pengujian alat pengering menggunakan tungku biomassa berbahan bakar tempurung kelapa dengan melakukan pengamatan suhu selama pengeringan, penurunan kadar air, waktu pengeringan, kebutuhan energi, efisiensi pengering, dan analisis finansial. Konstruksi alat pengering pati sagu model vibro fluidized bed bertenaga biomassa berukuran panjang, lebar dan tinggi masing-masing (200x50x1500 cm, serta memiliki daya tampung atau kapasitas maksimum pati sagu basah 35 kg/proses. Hasil pengujian menunjukkan bahwa alat pengering ini mampu mengeringkan pati sagu selama 7 jam, dengan konsumsi bahan bakar tempurung kelapa sebanyak 70 kg

Taxation on vehicle fuels: its impacts on switching to cleaner fuels

International Nuclear Information System (INIS)

Hung, W.-T.

2006-01-01

Vehicular consumption of fossil fuel contributes over 90% of air pollution in Hong Kong. A key strategy to improve Hong Kong's air quality is to discourage dirty fuels (e.g., leaded petrol and high-sulphur diesel) and to promote the use of clean fuels (e.g., low-sulphur diesel and liquefied petroleum gas (LPG)). This paper presents the empirical evidence on the effectiveness of the Government's clean fuel programs that offer tax subsidy to lower the consumption cost of such fuels. For the cases of unleaded petrol and ultra-low-sulphur diesel, lower fuel duties were offered so that the prices of these fuels were below those of leaded petrol and conventional diesel. Conventional petrol and diesel were phased out. In order to decide on the level of fuel duty concessions required to introduce LPG for taxis and bio-diesel for other vehicles, various Government-run trial programs were introduced to obtain cost estimates of using these alternative cleaner fuels. LPG using vehicles were subsequently exempted from the fuel duty in order to attract taxi and light bus operators to switch to LPG. It is apparent that the higher the subsidy, the faster is the rate at which switching to cleaner fuels takes place

Water resources protection today: end-of-pipe technology and cleaner production. Case study of the Czech Odra River watershed.

Science.gov (United States)

Chour, V

2001-01-01

This paper reports on integrated watershed-based protection and sustainable use of water resources to increase the effectiveness of water pollution abatement. The approach includes improvements in end-of-pipe waste-water treatment technologies and implementation of Cleaner Production (CP) principles and policies within the watershed. An example of the general effectiveness of this approach is illustrated by the Czech Odra River Cleaner Production Project where reductions in pollution were achieved with improved industrial production. The CP theme is worth considering as an important challenge for the IWA.

What drives successful implementation of pollution prevention and cleaner technology strategy? The role of innovative capability.

Science.gov (United States)

Bhupendra, Kumar Verma; Sangle, Shirish

2015-05-15

Firms that are dynamic and prepared to implement environmental strategies have a potential competitive advantage over their industry counterparts. Therefore, it is important to understand, what capabilities are required to implement proactive environmental strategies. The paper discusses the attributes of innovative capability required by firms in order to adopt pollution prevention and cleaner technology strategies. Empirical results show that process and behavioral innovativeness are required by firms to implement a pollution prevention strategy. In addition to process and behavioral innovativeness, firms need a top management with high risk-taking ability as well as market, product, and strategic innovativeness to implement a cleaner technology strategy. The paper proposes some important managerial implications on the basis of the above research findings. Copyright © 2015 Elsevier Ltd. All rights reserved.

Experimental investigation of a novel indirect solar dryer implementing PCM as energy storage medium

Energy Technology Data Exchange (ETDEWEB)

Shalaby, S.M., E-mail: saleh_shalaby@yahoo.com; Bek, M. A.

2014-07-01

Highlights: • The performance of a novel indirect solar dryer is investigated experimentally. • PCM, paraffin wax, is used as energy storage medium. • The novel ISD is suitable for drying medical plants. • Ocimum and Thevetia are dried at their prescribed drying temperatures. • The novel design maintains the desired temperature for 7 consecutive h/day. - Abstract: A novel indirect solar dryer (ISD) design using phase change material (PCM) as energy storage medium was experimentally investigated. The system consists of two identical solar air heaters, drying compartment, PCM storage units and a blower. The ISD was tested under no load with and without PCM at a wide range of mass flow rates (0.0664–0.2182 kg/s). It is found that after using the PCM, the temperature of the drying air is higher than ambient temperature by 2.5–7.5 °C after sunset for five hours at least. In addition, the mass flow rates of 0.1204 and 0.0894 kg/s give the peak values of the drying temperature when the ISD is operated with and without PCM, respectively. The novel design successfully maintains the desired temperature for seven consecutive hours every day. This helps reaching the final moisture content of Ocimum Basilicum and Thevetia Neriifolia after 12 and 18 h, respectively.

Drying kinetics of whole and sliced turmeric rhizomes (Curcuma longa L. in a solar conduction dryer

Directory of Open Access Journals (Sweden)

A. Borah

2015-09-01

Full Text Available Drying of turmeric was carried out in a solar conduction dryer (SCD. Drying air temperature was achieved around 39–51 °C for an ambient temperature in the range of 25–28 °C. Moisture content from 78.65% (wb, was reduced to 6.36% (wb and 5.50% (wb for solid and sliced samples respectively in 12 h effective drying time. Drying curve of sliced samples showed more uniform falling in comparison to that of whole samples. The average effective moisture diffusivity was found to be 1.852 × 10−10 m2 s−1 for slab samples and 1.456 × 10−10 m2 s−1 for solid samples. Out of four models tried for simulation, Page model was found as best fitted thin layer drying model when simulation was done for all the drying data. The overall thermal efficiency of the dryer was found to be 55%. Drying of sliced rhizomes showed better drying kinetics and effective drying time could be reduced by slicing instead of drying in whole form.

Simulation of Solar Heat Pump Dryer Directly Driven by Photovoltaic Panels

Science.gov (United States)

Houhou, H.; Yuan, W.; Wang, G.

2017-05-01

This paper investigates a new type of solar heat pump dryer directly driven by photovoltaic panels. In order to design this system, a mathematical model has been established describing the whole drying process, including models of key components and phenomena of heat and mass transfer at the product layer and the air. The results of simulation at different drying air temperatures and velocities have been calculated and it indicate that the temperature of drying air is crucial external parameter compared to the velocity, with the increase of drying temperature from 45°C to 55°C, the product moisture content (Kg water/Kg dry product) decreased from 0.75 Kg/Kg to 0.3 Kg/Kg.

China and Cleaner Coal. A marriage of necessity destined for failure?

International Nuclear Information System (INIS)

Seaman, John

2012-04-01

For China, coal is a crucial source of abundant, indigenous and affordable energy and is a pillar of economic and social stability. From a logic of energy security, and because the industry itself maintains a formidable political presence through the sheer fact of its history and size, this resource will continue to play a central role in the country's energy mix. But in order to respond to the growing need to reduce the burden of coal use on the environment and the Chinese population, and to prevent catastrophic climate change, both Chinese leaders and the industry itself have faced a certain reality - coal must become cleaner. This has led to a tenuous compromise between those in China advocating for the use of coal as a matter of economic necessity and social stability (security of supply, reliable and cheap electricity, and indigenous energy technologies) and those who strive for more environmentally sustainable growth (and thus emphasize 'clean' coal). The convergence of these two concepts has spurred a major shift towards newer, more efficient, though still highly polluting technologies - notably larger scale, hotter burning supercritical and ultra-supercritical coal-fired plants. But it has also spawned a number of demonstration-scale projects in various cutting-edge technologies to include coal gasification and carbon capture and storage (CCS), which promise vast improvements in CO_2 and other, toxic emissions if widely adopted. Indeed, mitigating climate change while continuing to rely heavily on coal will only be possible if carbon can successfully be captured and stored on a broad scale. The push to develop new coal technologies opens doors for both foreign and Chinese businesses to work together, potentially creating new market opportunities at home and abroad. Chinese companies can receive much-needed capital and expertise, while foreign companies and researchers are given the chance to test and develop technologies at a level of speed and scale that

Cleaner drive - Obstacles in the way of a market for a new generation of vehicles; Cleaner Drive. Hindernisse fuer die Markteinfuehrung von neuen Fahrzeug-Generationen. Bericht ueber die Beteiligung von e'mobile am EU-Projekt

Energy Technology Data Exchange (ETDEWEB)

Schwegler, U. [e' mobile, der Schweizerische Verband fuer elektrische und effiziente Strassenfahrzeuge, Berne (Switzerland); Domeniconi, R. [AssoVEL2, Mendrisio (Switzerland); Kaufmann, J. [Kaufmann Consulting, Berne (Switzerland); Werfeli, A. [Verband der Schweizerischen Gasindustrie, Zuerich (Switzerland)

2004-07-01

This final report for the Association of Swiss Traffic Engineers describes work done within the framework of the fifth European Research Framework Programme involving the development of tools to speed up the introduction of a new generations of vehicles. This report lists the work done by the Swiss e'mobil organisation and discusses the limitations placed on the work by its international framework. The report presents the 'Cleaner Drive' environmental evaluation methods used for vehicles. This considers greenhouse-gas emissions and external costs. Factors not considered, noise and bio-fuels, are mentioned. A data-base based decision-support tool is introduced. The development of the 'Cleaner Drive' web site is described. A further chapter takes a look at efforts being made in the area of filling stations for gaseous fuels.

Integrated Hydrologic Science and Environmental Engineering Observatory: CLEANER's Vision for the WATERS Network

Science.gov (United States)

Montgomery, J. L.; Minsker, B. S.; Schnoor, J.; Haas, C.; Bonner, J.; Driscoll, C.; Eschenbach, E.; Finholt, T.; Glass, J.; Harmon, T.; Johnson, J.; Krupnik, A.; Reible, D.; Sanderson, A.; Small, M.; van Briesen, J.

2006-05-01

With increasing population and urban development, societies grow more and more concerned over balancing the need to maintain adequate water supplies with that of ensuring the quality of surface and groundwater resources. For example, multiple stressors such as overfishing, runoff of nutrients from agricultural fields and confined animal feeding lots, and pathogens in urban stormwater can often overwhelm a single water body. Mitigating just one of these problems often depends on understanding how it relates to others and how stressors can vary in temporal and spatial scales. Researchers are now in a position to answer questions about multiscale, spatiotemporally distributed hydrologic and environmental phenomena through the use of remote and embedded networked sensing technologies. It is now possible for data streaming from sensor networks to be integrated by a rich cyberinfrastructure encompassing the innovative computing, visualization, and information archiving strategies needed to cope with the anticipated onslaught of data, and to turn that data around in the form of real-time water quantity and quality forecasting. Recognizing this potential, NSF awarded $2 million to a coalition of 12 institutions in July 2005 to establish the CLEANER Project Office (Collaborative Large-Scale Engineering Analysis Network for Environmental Research; http://cleaner.ncsa.uiuc.edu). Over the next two years the project office, in coordination with CUAHSI (Consortium of Universities for the Advancement of Hydrologic Science, Inc.; http://www.cuahsi.org), will work together to develop a plan for a WATer and Environmental Research Systems Network (WATERS Network), which is envisioned to be a collaborative scientific exploration and engineering analysis network, using high performance tools and infrastructure, to transform our scientific understanding of how water quantity, quality, and related earth system processes are affected by natural and human-induced changes to the environment

Evaluation of the efficacy of vacuum cleaners for the integrated control of brown spider Loxosceles intermedia

Directory of Open Access Journals (Sweden)

E. N. Ramires

2007-01-01

Full Text Available Some venomous spiders of the genus Loxosceles can reach high population densities inside and around houses. In Brazil, most spider accidents are related to Loxosceles intermedia. Control of loxoscelism should utilize integrated pest management tools, such as vacuum cleaners, to eliminate egg sacs, webs and spiders. The present study tested the efficacy of one type of vacuum cleaner (for professional and domestic use in the control of L. intermedia populations. Cockroaches (Pycnoscelus surinamensis were used in some tests for comparison. Vacuuming using standard accessories or a paper tube resulted in the death of all female (n=60, male (n=60, young (n=60 and just-hatched (n=60 L. intermedia, and all egg sacs (n=5 were destroyed. The removal of the plastic plate present at the bottom of the vacuuming tube inside the machine allowed some spiders to survive the vacuuming process. When kept inside a vacuum bag full of dust and debris, adult females (n=10 survived for 10 days; however, significant mortality was observed among male (n=10 and young individuals (n=10. Addition of cornstarch to the vacuum bag did not affect the spiders (n=20. Vacuum cleaners, such as the one used in the present investigation, are promising tools for integrated management of L. intermedia and other spiders in domestic environments.

IMPACT OF COSOLVENT FLUSHING ON SUBSURFACE MICROBIAL ECOLOGY AT THE FORMER SAGE'S DRY CLEANER SITE

Science.gov (United States)

The Solvent Extraction Residual Biotreatment (SERB) technology was evaluated at the former Sage's Dry Cleaner site in Jacksonville, FL where an area of tetrachloroethylene (PCE) contamination was identified. The SERB technology is a treatment train approach to complete site rest...

Seed regulations and local seed systems

NARCIS (Netherlands)

Louwaars, N.

2000-01-01

Seed regulations have been introduced in most countries based on the development of formal seed production. Concerns about seed quality and about the varietal identity of the seeds have commonly led to seed laws. However, formal regulations are often inappropriate for informal seed systems, which

The Infraordinary as Spatial Discourse: Tongue of the Dry Cleaner

DEFF Research Database (Denmark)

Lunde Nielsen, Espen

2014-01-01

Most of us pass along kiosks, pubs, dry cleaners, turn street corners, rise up stairways on a daily basis, in a sort of spatial anaesthesia. These spaces that facilitates our everyday existence are ‘worn half-invisible by use’, thereby not given due attention. Through his occupation with the infra...... and people of the neighbourhood coexist through events in real-time and depositions over time. The infra-ordinary as a spatial discourse interrogates and acknowledges the latent qualities of the common and seemingly banal, yet vitally important, spatial materiality of everyday life, as an alternative...

General wisdom concerning the factors affecting the adoption of cleaner technologies: a survey 1990-2007

NARCIS (Netherlands)

Montalvo Corral, C.

2008-01-01

Cleaner technologies (CT) have recently received much attention in diverse media and policy agendas. This comes out of the clear role they play in environmental protection and sustainability and the large potential to contribute to economic growth and competitiveness. The realization of both

Modification of Indirect Solar Dryer for Simplicia Production

Science.gov (United States)

Purnomo, C. W.; Indarti, S.

2018-03-01

Simplicia is natural ingredient for herbal medicine that has been subjected to drying only. This study aims to develop an appropriate drying equipment to produce dried leaves of sambung nyawa (Gynura procumbens (Lour.) Merr.) or also called “longevity spinach”. Typical indirect solar drier was modified to be able to process more fresh leaves in order to speed up the production. The modification was done using double solar collector and wind powered ventilation. The double solar collector was applied in order to collect more solar energy for larger dimension of drying chamber, while the wind-ventilator was installed to provide forced convection of hot air flow inside the dryer. The drying kinetic including the drying constants were investigated using three common thin layer drying equations to model the drying behavior of the leaves. The moisture ratio (MR) depletion with respect to the drying time (t) of the leaves can be well represented by equation of MR=1.1732exp(-0.0993.t)-0.1732exp(-17.3871.t).

Reactive adsorption: A cleaner technology in nuclear power plants

International Nuclear Information System (INIS)

Marton, G.; Szanya, T.; Hanak, L.

1996-01-01

Cleaner technology prefers work with minimal loss and the wastes cause the less environmental damages. In the spirit of the previous sentence in the present paper reactive adsorption is investigated for the removal of radioactive nuclides from nuclear power plant decontamination solutions. During alkaline, oxidative decontamination of nuclear power plant equipment a radioactive solution is produced. Owing to the storing difficulties of radioactive solutions it is necessary to develop a method for the in situ treatment of radioactive, alkaline, oxidative decontamination solutions, and for the concentration of radioactive components. Reactive adsorption seems to be promising for this purpose. 3 refs., 8 figs., 1 tab

Equal-sign lepton pairs: a cleaner W-signal in panti p collisions

International Nuclear Information System (INIS)

Abud, M.; Gatto, R.; Savoy, C.A.

1978-01-01

It is pointed out that the observation of the energetic equal-sign dileptons in high-energy panti p colliding beams may provide for a cleaner way of detecting the W. It is assumed that the most energetic dileptons come from the semileptonic decays of the t- and b-quarks. The authors calculate the dilepton signal from weak interaction and compare it with the strong interaction background as predicted by QCD. (Auth.)

Evaluation and mitigation of tritium memory in detritiation dryers

International Nuclear Information System (INIS)

Malara, C.; Ricapito, I.; Edwards, R.A.H.; Toci, F.

1999-01-01

In atmospheric detritiation, and other tritium processes, tritium is adsorbed on zeolites (molecular sieves) in the form of tritiated water. Regeneration removes almost all the physically adsorbed water, but a proportion remains permanently in the zeolite and binder structure as chemically bound water or hydroxyl groups. Exchange between adsorbed water and bound water means that tritiated water is retained in the structure after regeneration. At the end of its life, the zeolite therefore constitutes a tritiated waste. Furthermore, if an atmosphere detritiation dryer (ADD) gets highly contaminated from a tritium spill, retained tritium contaminates both the small amount of vapour leaving the bed during the next drying cycle, and the water produced in the subsequent regeneration. This report first describes experiments to measure the tritiated water retained in a 5A zeolite bed after standard regeneration treatments, and then investigates strategies to mitigate the effect: more thorough regeneration and isotope swamping or elution. The effect of zeolite ageing after thermal cycling is also seen. (orig.)

The performance of cleaner wrasse, Labroides dimidiatus, in a reversal learning task varies across experimental paradigms.

Science.gov (United States)

Gingins, Simon; Marcadier, Fanny; Wismer, Sharon; Krattinger, Océane; Quattrini, Fausto; Bshary, Redouan; Binning, Sandra A

2018-01-01

Testing performance in controlled laboratory experiments is a powerful tool for understanding the extent and evolution of cognitive abilities in non-human animals. However, cognitive testing is prone to a number of potential biases, which, if unnoticed or unaccounted for, may affect the conclusions drawn. We examined whether slight modifications to the experimental procedure and apparatus used in a spatial task and reversal learning task affected performance outcomes in the bluestreak cleaner wrasse, Labroides dimidiatus (hereafter "cleaners"). Using two-alternative forced-choice tests, fish had to learn to associate a food reward with a side (left or right) in their holding aquarium. Individuals were tested in one of four experimental treatments that differed slightly in procedure and/or physical set-up. Cleaners from all four treatment groups were equally able to solve the initial spatial task. However, groups differed in their ability to solve the reversal learning task: no individuals solved the reversal task when tested in small tanks with a transparent partition separating the two options, whereas over 50% of individuals solved the task when performed in a larger tank, or with an opaque partition. These results clearly show that seemingly insignificant details to the experimental set-up matter when testing performance in a spatial task and might significantly influence the outcome of experiments. These results echo previous calls for researchers to exercise caution when designing methodologies for cognition tasks to avoid misinterpretations.

Drying process optimization for an API solvate using heat transfer model of an agitated filter dryer.

Science.gov (United States)

Nere, Nandkishor K; Allen, Kimberley C; Marek, James C; Bordawekar, Shailendra V

2012-10-01

Drying an early stage active pharmaceutical ingredient candidate required excessively long cycle times in a pilot plant agitated filter dryer. The key to faster drying is to ensure sufficient heat transfer and minimize mass transfer limitations. Designing the right mixing protocol is of utmost importance to achieve efficient heat transfer. To this order, a composite model was developed for the removal of bound solvent that incorporates models for heat transfer and desolvation kinetics. The proposed heat transfer model differs from previously reported models in two respects: it accounts for the effects of a gas gap between the vessel wall and solids on the overall heat transfer coefficient, and headspace pressure on the mean free path length of the inert gas and thereby on the heat transfer between the vessel wall and the first layer of solids. A computational methodology was developed incorporating the effects of mixing and headspace pressure to simulate the drying profile using a modified model framework within the Dynochem software. A dryer operational protocol was designed based on the desolvation kinetics, thermal stability studies of wet and dry cake, and the understanding gained through model simulations, resulting in a multifold reduction in drying time. Copyright © 2012 Wiley-Liss, Inc.

Comparison of Linear and Nonlinear Model Predictive Control for Optimization of Spray Dryer Operation

DEFF Research Database (Denmark)

Petersen, Lars Norbert; Poulsen, Niels Kjølstad; Niemann, Hans Henrik

2015-01-01

In this paper, we compare the performance of an economically optimizing Nonlinear Model Predictive Controller (E-NMPC) to a linear tracking Model Predictive Controller (MPC) for a spray drying plant. We find in this simulation study, that the economic performance of the two controllers are almost...... equal. We evaluate the economic performance with an industrially recorded disturbance scenario, where unmeasured disturbances and model mismatch are present. The state of the spray dryer, used in the E-NMPC and MPC, is estimated using Kalman Filters with noise covariances estimated by a maximum...

Design and measured performance of a solar chimney for natural-circulation solar-energy dryers

International Nuclear Information System (INIS)

Ekechukwu, O.V.; Norton, B.

1995-10-01

The design and construction of a solar chimney which was undertaken as part of a study on natural-circulation solar-energy dryers is reported. The experimental solar chimney consists of a 5.3m high and 1.64m diameter cylindrical polyethylene-clad vertical chamber, supported structurally by steel framework and draped internally with a selectively-absorbing surface. The performance of the chimney which was monitored extensively with and without the selective surface in place (to study the effectiveness of this design option) is also reported. (author). 14 refs, 7 figs

Mushrooms dehydration in a hybrid-solar dryer, using a phase change material

International Nuclear Information System (INIS)

Reyes, Alejandro; Mahn, Andrea; Vásquez, Francisco

2014-01-01

Highlights: • Mushroom slices were dehydrated in a hybrid solar dryer. • Drying and dehydrated kinetics were adjusted with models. • Effective diffusivity, were estimated considering or not shrinkage. • Paraffin wax as a phase change material was used in an accumulator of solar energy. - Abstract: Mushrooms were dehydrated in a hybrid solar dryer provided with a solar panel of a total exposed surface of 10 m 2 , electric resistances and paraffin wax as a phase change material. Mushrooms were cut in 8 mm or 12 mm slices. At the outlet of the drying chamber the air was recycled (70% or 80%) and the air temperature was adjusted to 60 °C. At the outlet of the solar panel the air temperature rose up to 30 °C above the ambient temperature, depending on solar radiation level. The effective diffusivity, estimated by the Simplified Constant Diffusivity Model, considering or not shrinkage, fluctuated between 2.5 · 10 −10 m 2 /s and 8.4 · 10 −10 m 2 /s with R 2 higher than 0.99, agreeing with values reported in literature. The empirical Page’s model resulted in a better adjustment, with R 2 above 0.998. In all runs the dehydrated mushrooms showed a notorious darkening and shrinkage. Rehydration assays at 30 °C showed that in less than 30 min rehydrated mushrooms reached a moisture content of 1.91 (dry basis). Rehydrated mushrooms had a higher hardness compared with fresh mushrooms. The Simplified Constant Diffusivity Model and the Peleg’s model adjusted to the rehydration data with RMSE values below 0.080. Thermal efficiency fluctuated between 22% and 62%, while the efficiency of the accumulator panel varied between 10% and 21%. The accumulator allowed reducing the electric energy input

Effort-reward imbalance at work and self-rated health of Las Vegas hotel room cleaners.

Science.gov (United States)

Krause, Niklas; Rugulies, Reiner; Maslach, Christina

2010-04-01

This study investigates the relationship between effort-reward-imbalance (ERI) at work and self-rated health (SF-36) among 941 Las Vegas hotel room cleaners (99% female, 84% immigrant). Logistic regression models adjust for age, health behaviors, physical workload and other potential confounders. 50% reported ERI and 60% poor or fair general health. Significant associations were found between ERI and all SF-36 health measures. Workers in the upper quartile of the efforts/rewards ratio were 2-5 times more likely to experience poor or fair general health, low physical function, high levels of pain, fatigue, and role limitations due to physical and mental health problems. The cross-sectional design limits causal interpretation of these associations. However, the development of interventions to reduce ERI and to improve general health among room cleaners deserves high priority considering that both high ERI and low self-rated health have predicted chronic diseases and mortality in prospective studies. (c) 2009 Wiley-Liss, Inc.

Analysis of efficiency of a solar dryer tunnel type of mango pulp; Analisis de la eficiencia de un secador solar tipo tunel para pulpa de mango

Energy Technology Data Exchange (ETDEWEB)

Chagoyan Serrano, Jose [Universidad Autonoma de Baja California Sur, La Paz, Baja California Sur (Mexico)

2000-07-01

A new method to assess the performance of a solar dryer is presented. It describes energy efficiency indicators to improve a commercial dryer design. First, a preliminary dryer design procedure is described step by step. Then, two different modes of a tunnel dryer are investigated: Batch and semi-continue operations. The results of the analysis show that, the thermal efficiency is not sufficient to rate de dryer performance. It is necessary to include the productivity of the drying process and the quality of the dried fruit. The drying process and productivity tend to go hand-in-hand but in opposite directions. That is to say, raising the thermal efficiency reduce the process productivity and conversely. The analysis also suggests that an agreement between the efficiency, productivity and the quality must be specified in the drier design. [Spanish] Se presenta un procedimiento nuevo para evaluar la operacion de un secador solar, con el cual se precisan indicadores de la eficiencia que pueden ser utiles para mejorar el diseno del equipo. Se empieza por describir los pasos de un procedimiento de diseno preliminar de un sistema de secado. Despues, se analizan cualitativamente dos secadores: uno que opera por lotes y el otro de modo semicontinuo. Los resultados del analisis muestran que, la eficiencia termica del equipo no es un criterio suficiente para evaluar su operacion; tambien se requiere tomar encuenta la productividad del proceso de secado y la calidad del producto final. Se concluye que la eficiencia termica y la productividad del proceso son conceptos encontrados. Es decir, la eficiencia termica del equipo no es un criterio suficiente para evaluar su operacion; tambien se requiere tomar en cuenta la productividad del proceso de secado y la calidad del producto final. Se concluye que la eficiencia termica y la productividad del proceso son conceptos encontrados. Es decir, la eficiencia termica solo se puede aumentar a costa de la productividad y viceversa

Strategies to overcome barriers for cleaner generation technologies in small developing power systems: Sri Lanka case study

International Nuclear Information System (INIS)

Wijayatunga, Priyantha D.C.; Siriwardena, Kanchana; Fernando, W.J.L.S.; Shrestha, Ram M.; Attalage, Rahula A.

2006-01-01

The penetration of cleaner and energy efficient technologies in small power systems such as the one in Sri Lanka has encountered many problems. This has caused major concerns among the policy makers, mainly in the context of the growing need to reduce harmful emissions in the electricity supply industry from the point of view of both local environmental pollution as well as the global warming concerns. This paper presents the outcome of a study involved in identifying and ranking the barriers to the promotion of cleaner and energy efficient technologies and strategies to overcome these barriers in Sri Lanka. Barriers for renewable energy based systems such as wind and wood fuel fired plants (dendro thermal power) and cleaner technologies such as liquefied natural gas (LNG) fired combined cycle and IGCC (coal) were identified based on a survey. A direct assessment multi-criteria decision making method called Analytic Hierarchy Process (AHP) was used to rank the barriers. The most effective strategies are proposed to address the three major barriers for each of these technologies based on extensive discussions with all the stakeholders in the electricity industry. It was found that lack of financing instruments, high initial cost and lack of assurance of resource supply or availability are the main barriers for renewable technologies. As for cleaner fuel and technology options associated with conventional generation systems, the lack of a clear government policy, uncertainty of fuel supplies and their prices and the reliability of the technologies themselves are the major barriers. Strategies are identified to overcome the above barriers. Establishment of a proper feed in tariff, geographical diversification of installations and capacity building in commercial banks are suggested for wind power. Investment incentives, streamlining of wood production and research on site identification are proposed for wood fuel fired plants. Also the study suggests delayed

The importance of integrated system design for the effectiveness of portable air cleaners in airborne infection

CSIR Research Space (South Africa)

Van Reenen, T

2013-12-01

Full Text Available The results of the recent study into the effectiveness of portable air cleaners (PACs), as an infection control measure against TB, delivered unexpectedly low results. That finding initiated a further study to understand the contribution of system...

Two-dimensional mathematical model for simulation of the drying process of thick layers of natural materials in a conveyor-belt dryer

Directory of Open Access Journals (Sweden)

Salemović Duško R.

2017-01-01

Full Text Available This paper presents the mathematical model and numerical analysis of the convective drying process of thick slices of colloidal capillary-porous materials slowly moving through conveyor-belt dryer. A flow of hot moist air was used as drying agent. The drying process has been analyzed in the form of a 2-D mathematical model, in two directions: along the conveyor and perpendicular on it. The mathematical model consists of two non-linear differential equations and one equation with a transcendent character and it is based on the mathematical model developed for drying process in a form of a 1-D thin layer. The appropriate boundary conditions were introduced. The presented model is suitable for the automated control of conveyor-belt dryers. The obtained results with analysis could be useful in predicting the drying kinetics of potato slices and similar natural products.

Overview of cleaner production as a result of clean technology research in Vietnam

Energy Technology Data Exchange (ETDEWEB)

Sam, D.V.; Nhan, T.V.; Lan, N.N. [Hanoi Univ. of Technology (Viet Nam)

1996-12-31

Vietnam is beginning its industrialization process, and it currently lacks the capital necessary for expensive pollution control and treatment systems. Pollution strategies are critical for the country. This study evaluates the present status of industry and the pollution problems associated with industrial development in Vietnam. The purpose of the study is to identify sectors that may have potential for promoting cleaner production practices. 4 refs.

Assessment of the environmental microbiological cross contamination following hand drying with paper hand towels or an air blade dryer.

Science.gov (United States)

Margas, E; Maguire, E; Berland, C R; Welander, F; Holah, J T

2013-08-01

This study compared the potential for cross contamination of the surrounding environment resulting from two different hand-drying methods: paper towels and the use of an air blade dryer. One hundred volunteers for each method washed their hands and dried them using one of the two methods. Bacterial contamination of the surrounding environment was measured using settle plates placed on the floor in a grid pattern, air sampling and surface swabs. Both drying methods produced ballistic droplets in the immediate vicinity of the hand-drying process. The air blade dryer produced a larger number of droplets which were dispersed over a larger area. Settle plates showed increased microbial contamination in the grid squares which were affected by ballistic droplets. Using the settle plates counts, it was estimated that approx. 1.7 × 10(5) cfu more micro-organisms were left on the laboratory floor (total area approx. 17.15 m(2)) after 100 volunteers used an air blade dryer compared to when paper towels were used. The two drying methods led to different patterns of ballistic droplets and levels of microbial contamination under heavy use conditions. Whilst the increase in microbial levels in the environment is not significant if only nonpathogenic micro-organisms are spread, it may increase the risk of pathogen contamination of the environment when pathogens are occasionally present on people's hands. The study suggests that the risk of cross contamination from the washroom users to the environment and subsequent users should be considered when choosing a hand-drying method. The data could potentially give guidance following the selection of drying methods on implementing measures to minimise the risk of cross contamination. © 2013 The Society for Applied Microbiology.

Lipophilic Super-Absorbent Swelling Gels as Cleaners for Use on Weapons Systems and Platforms

Science.gov (United States)

2014-02-01

Tetrahydrofuran (THF), isopropa- nol, acetonitrile, and dichloromethane were obtained from Acros Organics (Morris Plains, NJ). Dimethylsulfoxide ( DMSO ) and 1...1. In the following solvents , swelling degree did not change in both heating and cooling processes: water, DMSO , methanol, ethanol, isopropanol...available alkylstyrene copolymer (imbiber beads). The cleaning ability of the gels was compared with the standard solvent cleaner trichloroethylene

Performance Analysis of Solar Assisted Fluidized Bed Dryer Integrated Biomass Furnace with and without Heat Pump for Drying of Paddy

Directory of Open Access Journals (Sweden)

M. Yahya

2016-01-01

Full Text Available The performances of a solar assisted fluidized bed dryer integrated biomass furnace (SA-FBDIBF and a solar assisted heat pump fluidized bed dryer integrated biomass furnace (SAHP-FBDIBF for drying of paddy have been evaluated, and also drying kinetics of paddy were determined. The SA-FBDIBF and the SAHP-FBDIBF were used to dry paddy from 11 kg with moisture content of 32.85% db to moisture content of 16.29% db (14% wb under an air mass flow rate of 0.1037 kg/s within 29.73 minutes and 22.95 minutes, with average temperatures and relative humidities of 80.3°C and 80.9°C and 12.28% and 8.14%, respectively. The average drying rate, specific energy consumption, and specific moisture extraction rate were 0.043 kg/minute and 0.050 kg/minute, 5.454 kWh/kg and 4.763 kWh/kg, and 0.204 kg/kWh and 0.241 kg/kWh for SA-FBDIBF and SAHP-FBDIBF, respectively. In SA-FBDIBF and SAHP-FBDIBF, the dryer thermal efficiencies were average values of 12.28% and 15.44%; in addition, the pickup efficiencies were 33.55% and 43.84% on average, whereas the average solar and biomass fractions were 10.9% and 10.6% and 36.6% and 30.4% for SA-FBDIBF and SAHP-FBDIBF, respectively. The drying of paddy occurred in the falling rate period. The experimental dimensionless moisture content data were fitted to three mathematical models. Page’s model was found best to describe the drying behaviour of paddy.

Radiation technology helps China’s industries make water cleaner

International Nuclear Information System (INIS)

Jawerth, Nicole

2015-01-01

China is pursuing the use of radiation technology as part of its wastewater treatment methods to further efforts to manage industrial waste in an environmentally friendly way. “Treating the water that comes from our industries is very important, so we have been doing this for a long time. Now we want to become better at making our water cleaner,” said Jianlong Wang, Vice-President of the Institute of Nuclear and New Energy Technology (INET) at Tsinghua University in Beijing. “We are receiving a lot of support from the IAEA to use electron beam based technologies to help us get rid of various water pollutants that the other methods cannot do on their own.”

The ecological significance of juvenile Diplodus sargus as ectoparasite fish cleaners in the north-eastern Atlantic

Directory of Open Access Journals (Sweden)

José Neto

2015-11-01

Full Text Available Cleaning behaviour was recently described for the omnivorous species Diplodus sargus. Although previous studies have reported the existence of ectoparasites in the stomach contents of some individuals this commercially important fish was never considered a cleaner species. Here we make the first characterization of this behaviour based on field observations. This behaviour was exclusively performed by juvenile D. sargus and, until now, was only observed in confined or semi-confined areas such as coastal lagoons or harbours. Unexpectedly, cleaning rates and the number of individuals performing this behaviour largely exceeds the ones described for a sympatric cleaner fish (13.98 cleaning events/individual/hour compared to 5.08 in Centrolabrus exoletus. Clients belong to several fish families (e.g. Mugilidae, Sparidae and Labridae that include some of the most common species in coastal habitats. Frequently, clients request cleaning by tilting their body or remaining motionless near the surface while being cleaned (40% however, in most cases, the interaction ends because clients flee (46%. This could mean that D. sargus is also feeding on mucus and/or living tissue. These shifts between exploitation and cooperation have been frequently described for tropical reef species. Our results support cooperative behaviour, with a clear correlation between the number of nips per cleaning event or the number of nips to which the client reacted positively and cleaning event duration (n=552; Spearman correlation r=0.79, p<0.001; r=0.76, p<0.001, respectively. Furthermore, no correlation was detected between the number of jolts by the client fish and the cleaning event duration (n=552; Spearman correlation r=0.07, p=0.105 meaning that jolting does not increase with increased interaction time. In the future, the evaluation of the ecological importance of D. sargus as a cleaner species in the North-Eastern Atlantic, should proceed with field observations in

Energy and exergy analyses of native cassava starch drying in a tray dryer

International Nuclear Information System (INIS)

Aviara, Ndubisi A.; Onuoha, Lovelyn N.; Falola, Oluwakemi E.; Igbeka, Joseph C.

2014-01-01

Energy and exergy analyses of native cassava starch drying in a tray dryer were carried out to assess the performance of the system in terms of energy utilization, energy utilization ratio, energy efficiency, exergy inflow and outflow, exergy loss and exegetic efficiency. The results indicated that for the starch with ash content of 0.76%, 0.85% crude protein, 0.16% crude fat, negligible amount of fiber, average granule size of 14.1 μm, pH of 5.88, amylose content of 23.45% and degree of crystallinity of 22.34%, energy utilization and energy utilization ratio increased from 1.93 to 5.51 J/s and 0.65 to 0.6 as the drying temperature increased from 40 to 60 °C. Energy efficiency increased from 16.036 to 30.645%, while exergy inflow, outflow and losses increased from 0.399 to 2.686, 0.055 to 0.555 and 0.344 to 2.131 J/s respectively in the above temperature range. Exergetic efficiency increased with increase in both drying air temperature and energy utilization and was lower than energy efficiency. Exergetic improvement potential also increased with increase in drying air temperature. Model equations that could be used to express the energy and exergy parameters as a function of drying temperature were established. - Highlights: • Energy and exergy analyses of cassava starch drying in a tray dryer were carried out. • Energy utilization increased with drying temperature. • Energy efficiency was higher than exergy efficiency. • Energy and exergy efficiencies increased with increase in temperature. • Improvement potential increased with increase in temperature

Separate and unsanitary: African American women railroad car cleaners and the Women's Service Section, 1918-1920.

Science.gov (United States)

Muhammad, Robin Dearmon

2011-01-01

The Women's Service Section (WSS) investigated federally controlled railroad stations and yards at the end of World War I. Few women worked in car cleaning before the war, and railroad management preferred to block women workers, especially African Americans, from gaining any kind of foothold in railroad work. African American women were the single largest group of railroad car cleaners during this period but they were routinely denied adequate facilities, including toilets, locker rooms, and dining facilities throughout the railroad system. By raising the issues of facilities, workers' rights, and public health, these women shaped federal policy and widened the agenda of the WSS to include a direct attack on segregated workplaces. This article argues that African American women car cleaners launched an industrial campaign that wove together concerns about racism, sexism, and health issues, and successfully removed barriers to women working in a predominately male industry.

Solar energy in food processing-a critical appraisal.

Science.gov (United States)

Eswara, Amruta R; Ramakrishnarao, M

2013-04-01

Increasing population and high cost of fuels have created opportunities for using alternate energies for post-harvest processing of foods. Solar food processing is an emerging technology that provides good quality foods at low or no additional fuel costs. A number of solar dryers, collectors and concentrators are currently being used for various steps in food processing and value addition. Society for Energy, Environment and Development (SEED) developed Solar Cabinet Dryer with forced circulation which has been used for dehydration and development of value added products from locally grown fruits, vegetables, leafy greens and forest produce. Drying under simulated shade conditions using UV-reducing Blue filter helps retain nutrients better. Its simple design and ease of handling makes SEED Solar Dryer an ideal choice for application of food processing in rural settings, closer to where the harvest is produced, eliminating the need for expensive transportation or storage of fresh produce. It also creates employment opportunities among the rural population, especially women. Other gadgets based on solar collectors and concentrators currently being used at various steps of food processing are reviewed.

Ocean cleaning stations under a changing climate: biological responses of tropical and temperate fish-cleaner shrimp to global warming.

Science.gov (United States)

Rosa, Rui; Lopes, Ana Rita; Pimentel, Marta; Faleiro, Filipa; Baptista, Miguel; Trübenbach, Katja; Narciso, Luis; Dionísio, Gisela; Pegado, Maria Rita; Repolho, Tiago; Calado, Ricardo; Diniz, Mário

2014-10-01

Cleaning symbioses play an important role in the health of certain coastal marine communities. These interspecific associations often occur at specific sites (cleaning stations) where a cleaner organism (commonly a fish or shrimp) removes ectoparasites/damaged tissue from a 'client' (a larger cooperating fish). At present, the potential impact of climate change on the fitness of cleaner organisms remains unknown. This study investigated the physiological and biochemical responses of tropical (Lysmata amboinensis) and temperate (L. seticaudata) cleaner shrimp to global warming. Specifically, thermal limits (CTMax), metabolic rates, thermal sensitivity, heat shock response (HSR), lipid peroxidation [malondialdehyde (MDA) concentration], lactate levels, antioxidant (GST, SOD and catalase) and digestive enzyme activities (trypsin and alkaline phosphatase) at current and warming (+3 °C) temperature conditions. In contrast to the temperate species, CTMax values decreased significantly from current (24-27 °C) to warming temperature conditions (30 °C) for the tropical shrimp, where metabolic thermal sensitivity was affected and the HSR was significantly reduced. MDA levels in tropical shrimp increased dramatically, indicating extreme cellular lipid peroxidation, which was not observed in the temperate shrimp. Lactate levels, GST and SOD activities were significantly enhanced within the muscle tissue of the tropical species. Digestive enzyme activities in the hepatopancreas of both species were significantly decreased by warmer temperatures. Our data suggest that the tropical cleaner shrimp will be more vulnerable to global warming than the temperate Lysmata seticaudata; the latter evolved in a relatively unstable environment with seasonal thermal variations that may have conferred greater adaptive plasticity. Thus, tropical cleaning symbioses may be challenged at a greater degree by warming-related anthropogenic forcing, with potential cascading effects on the health

Study on demetalization of sewage sludge by sequential extraction before liquefaction for the production of cleaner bio-oil and bio-char.

Science.gov (United States)

Leng, Lijian; Yuan, Xingzhong; Shao, Jianguang; Huang, Huajun; Wang, Hou; Li, Hui; Chen, Xiaohong; Zeng, Guangming

2016-01-01

Demetalization of sewage sludge (SS) by sequential extraction before liquefaction was implemented to produce cleaner bio-char and bio-oil. Demetalization steps 1 and 2 did not cause much organic matter loss on SS, and thus the bio-oil and bio-char yields and the compositions of bio-oils were also not affected significantly. However, the demetalization procedures resulted in the production of cleaner bio-chars and bio-oils. The total concentrations and the acid soluble/exchangeable fraction (F1 fraction, the most toxic heavy metal fraction) of heavy metals (Cu, Cr, Pb, Zn, and Cd) in these products were significantly reduced and the environmental risks of these products were also relived considerably compared with those produced from raw SS, respectively. Additionally, these bio-oils had less heavy fractions. Demetalization processes with removal of F1 and F2 fractions of heavy metals would benefit the production of cleaner bio-char and bio-oil by liquefaction of heavy metal abundant biomass like SS. Copyright © 2015 Elsevier Ltd. All rights reserved.

Experimental investigation of an indirect solar dryer integrated with phase change material for drying valeriana jatamansi (medicinal herb

Directory of Open Access Journals (Sweden)

A.K. Bhardwaj

2017-09-01

Full Text Available In this study, an experimental investigation of an indirect solar dryer integrated with phase change material has been carried out for drying Valeriana Jatamansi. The experimentation has been performed under the climatic conditions of Himalayan region, Solan (latitude − 30.91°N, longitude − 77.09°E, Himachal Pradesh (India in the month of October-November 2016. Paraffin RT-42 has been used as a phase change material in the dryer. Using this system, the moisture content of rhizomes reduced from 89% to 9% in 5 days as compared to heat pump drying and shade drying, which took 8 days and 14 days, respectively. Results of present study infer that the drying time using phase change material in this setup has reduced by 37.50% and 64.29% when compared to heat pump drying and shade drying, respectively. The dried rhizomes obtained are of superior quality in terms of colour, texture, aroma and bio-medical constituents. Analyses show that by using present setup, total valepotriates obtained were 3.47% as compared to traditional shade drying which yield 3.31%.

Investigations of a type 316L steam dryer plate material suffering from IGSCC after few years in BWRs

International Nuclear Information System (INIS)

Autio, J.M.; Ehrnsten, U.; Pakarinen, J.; Mouginot, R.; Cocco, M.

2015-01-01

A steam dryer plate material suffered from intergranular stress corrosion cracking after only one and two years of operation in two BWR plants. Numerous indications were observed on the inner roof plates of the steam dryers adjacent to the support beam welds. The material was Type 316L austenitic stainless steel with carbon content below 0.02%. The material was subjected to detailed investigations using optical microscopy, EBSD/SEM, TEM, hardness and nano-indentation. The material showed macro-segregation through the plate thickness. These bands coincided with the location of delta-ferrite islands indicating non-optimal solution heat treatment. α'-martensite was observed deep in the plate indicating cold deformation after solution annealing. A nonhomogeneous distribution of grain orientation was also observed through the plate thickness. Further, surface deformation, although not extending very deep, was observed using EBSD and surface hardness values above 300 HV when measured using small loads. Although the material fulfills the set requirements, the material characteristics have obviously increased the susceptibility of the material to IGSCC. The paper will discuss the possible role of changes in manufacturing over the years and the challenges in quality definitions in material specifications. (authors)

Cleaner metallurgical industry in Serbia: a road to the sustainable development

Directory of Open Access Journals (Sweden)

D. Panias

2009-01-01

Full Text Available Since the sustainable development has been a global and fundamental objecttive, a metallurgical industrial sector faces some of the most difficult sustainability challenges of any industrial sector. On the other hand, the metallurgical production in Serbia is a very important part of the economy. Due to present facilities and technologies, metallurgical companies face a great challenge to fulfill the requirements introduced by legislature referring to the cleaner production and sustainable development. The state of art in the production, facilities, pollution with some answers to imposed challenges is presented.

CFD Analysis to Calculate the Optimal Air Velocity in Drying Green Tea Process Using Fluidized Bed Dryer

Science.gov (United States)

Yohana, Eflita; Nugraha, Afif Prasetya; Diana, Ade Eva; Mahawan, Ilham; Nugroho, Sri

2018-02-01

Tea processing is basically distinguished into three types which black tea, green tea, and oolong tea. Green tea is processed by heating and drying the leaves. Green tea factories in Indonesia are generally using the process of drying by panning the leaves. It is more recommended to use the fluidization process to speed up the drying process as the quality of the tea can be maintained. Bubbling fluidization is expected to occur in this research. It is a process of bubbles are formed in the fluidization. The effectiveness of the drying process in a fluidized bed dryer machine needs to be improved by using a CFD simulation method to proof that umf < u < ut, where the average velocity value is limited by the minimum and the maximum velocity of the calculation the experimental data. The minimum and the maximum velocity value of the fluidization is 0.96 m/s and 8.2 m/s. The result of the simulation obtained that the average velocity of the upper bed part is 1.81 m/s. From the results obtained, it can be concluded that the calculation and the simulation data is in accordance with the condition of bubbling fluidization in fluidized bed dryer.

Building solar dryer of tropical woods; Construccion de un secador solar de maderas tropicales

Energy Technology Data Exchange (ETDEWEB)

Hernandez R, J; Flores M, F. E; Cuevas D, O [Universidad de Quintana Roo, Chetumal, Quintana Roo (Mexico); Tolentino E, G [LABINTHAP-SEPI-ESIME-IPN, Mexico, D.F. (Mexico)

2000-07-01

In Quintana Roo, Mexico, several species of wood are used for handicrafts. The most commonly method used in the communities nearby Chetumal is natural drying, with the disadvantage of low quality in their products because the moisture contains in the wood. In this project studied the design of solar dryer for tropical woods in Quintana Roo. [Spanish] En este trabajo, se parte del analisis de las condiciones climatologicas existentes en el estado de Quintana Roo, Mexico, asi como de las necesidades de madera seca de una comunidad, como parametros basicos para el diseno y construccion de un secador solar de maderas tropicales.

Bacterial and fungal aerosols in the work environment of cleaners

Directory of Open Access Journals (Sweden)

Małgorzata Gołofit-Szymczak

2015-12-01

Full Text Available Background: Cleaning services are carried out in almost all sectors and branches of industry. Due to the above, cleaners are exposed to various harmful biological agents, depending on the tasks performed and the commercial sector involved. The aim of this study was to assess the exposure of cleaning workers to biological agents based on quantitative and qualitative characteristics of airborne microflora. Material and methods: A six-stage Andersen sampler was used to collect bioaerosols during the cleaning activities in different workplaces, including schools, offices, car services, healthy services and shops. Standard Petri dishes filled with blood trypticase soy agar and malt extract agar were used for bacterial and fungal sampling, respectively. Results: The bioaerosol concentration values obtained during testing of selected workposts of cleaners were lower than the Polish recommended threshold limit values for microorganisms concentrations in public service. The most prevalent bacterial species in studied places were Gram-positive cocci (mainly of genera Micrococcus, Staphylococcus and endospore-forming Gram-positive rods (mainly of genera Bacillus. Among the most common fungal species were those from genera Penicillium and Aspergillus. The size distribution analysis revealed that bioaerosols present in the air of workposts at shops, schools and car services may be responsible for nose and eye mucosa irritation and allergic reactions in the form of asthma or allergic inflammation in the cleaning workers. Conclusions: The study shows that occupational activities of cleaning workers are associated with exposure to airborne biological agents classified into risk groups, 1. and 2., according to their level of infection risk, posing respiratory hazard. Med Pr 2015;66(6:779–791

Design and performance of a Nafion dryer for continuous operation at CO2 and CH4 air monitoring sites

Directory of Open Access Journals (Sweden)

L. R. Welp

2013-05-01

Full Text Available In preparation for routine deployment in a network of greenhouse gas monitoring stations, we have designed and tested a simple method for drying ambient air to near or below 0.2% (2000 ppm mole fraction H2O using a Nafion dryer. The inlet system was designed for use with cavity ring-down spectrometer (CRDS analyzers such as the Picarro model G2301 that measure H2O in addition to their principal analytes, in this case CO2 and CH4. These analyzers report dry-gas mixing ratios without drying the sample by measuring H2O mixing ratio at the same frequency as the main analytes, and then correcting for the dilution and peak broadening effects of H2O on the mixing ratios of the other analytes measured in moist air. However, it is difficult to accurately validate the water vapor correction in the field. By substantially lowering the amount of H2O in the sample, uncertainties in the applied water vapor corrections can be reduced by an order of magnitude or more, thus eliminating the need to determine instrument-specific water vapor correction coefficients and to verify the stability over time. Our Nafion drying inlet system takes advantage of the extra capacity of the analyzer pump to redirect 30% of the dry gas exiting the Nafion to the outer shell side of the dryer and has no consumables. We tested the Nafion dryer against a cryotrap (−97 °C method for removing H2O and found that in wet-air tests, the Nafion reduces the CO2 dry-gas mixing ratios of the sample gas by as much as 0.1 ± 0.01 ppm due to leakage across the membrane. The effect on CH4 was smaller and varied within ± 0.2 ppb, with an approximate uncertainty of 0.1 ppb. The Nafion-induced CO2 bias is partially offset by sending the dry reference gases through the Nafion dryer as well. The residual bias due to the impact of moisture differences between sample and reference gas on the permeation through the Nafion was approximately −0.05 ppm for CO2 and varied within ± 0.2 ppb for CH4. The

Cleaner production at pharmaceutical industry: first steps assessment

Directory of Open Access Journals (Sweden)

Edilaine Conceição Rezende

2015-12-01

Full Text Available The Cleaner Production (CP is an environmental management system effective to comply the environmental obligations and promote sustainable development of enterprises. In this study, the implementing possibilities of CP practices were evaluated to pharmaceutical industry, through prior identification procedures for Pharmaceutical Manufacturing Practices. The study was conducted in a scientific and health care institution, which produces pharmaceutical drugs and makes assistance for public health. The production process was evaluated and made a survey of the main points of waste and sewage generations in each stage, in order to diagnose the measures of CP established and propose new actions. Thus, by using this tool, it was possible to demonstrate the reduction of environmental impacts associated with pharmaceutical production. The Pharmaceutical Manufacturing Practices also contributed to the implementation of measures CP, preserving the final product quality, and generating environmental and economic benefits.

Irradiation effect on the seed vigor, SOD activity and MDA content in germinating seeds of yellow-seeded and black-seeded rape seed (Brassica napus L.)

International Nuclear Information System (INIS)

Han Jixiang; Hu Danhong; Liu Houli

1993-01-01

Seeds of a set of near-isogenic lines (Brassica napus L.) with different seed coat color from yellow to black were irradiated by 60 Co γ-rays of 150 krad. Seed vigor, superoxide dismutase (SOD) and malondialdehyde (MDA) in germinating seeds were analysed. In these characters, no significant difference between yellow-seeded lines (YLs) and black-seeded lines (BLs) showed before irradiation. But after irradiation, SOD activity in YLs was lower than that in BLs. While MDA content in YLs was obviously higher that that in DLs. As a result of irradiation, seed vigor of YLs was lower than that in BLs. these results indicated that the irradiation resistance of rape seed was related to the level of SOD as well as protective structure or substances in seed coat and that the radiosensitivity of YLs was higher than that of DLs

CHARACTERIZATION OF OZONE EMISSIONS FROM AIR CLEANERS EQUIPPED WITH OZONE GENERATORS AND SENSOR AND FEEDBACK CONTROL CIRCUITRY

Science.gov (United States)

The paper give results of a characterization of ozone emissions from air cleaners equipped with ozone generators and sensor and feedback control circuitry. Ozone emission rates of several consumer appliances, marketed as indoor air treatment or air purification systems, were det...

Breakage and drying behaviour of granules in a continuous fluid bed dryer: Influence of process parameters and wet granule transfer.

Science.gov (United States)

De Leersnyder, F; Vanhoorne, V; Bekaert, H; Vercruysse, J; Ghijs, M; Bostijn, N; Verstraeten, M; Cappuyns, P; Van Assche, I; Vander Heyden, Y; Ziemons, E; Remon, J P; Nopens, I; Vervaet, C; De Beer, T

2018-03-30

Although twin screw granulation has already been widely studied in recent years, only few studies addressed the subsequent continuous drying which is required after wet granulation and still suffers from a lack of detailed understanding. The latter is important for optimisation and control and, hence, a cost-effective practical implementation. Therefore, the aim of the current study is to increase understanding of the drying kinetics and the breakage and attrition phenomena during fluid bed drying after continuous twin screw granulation. Experiments were performed on a continuous manufacturing line consisting of a twin-screw granulator, a six-segmented fluid bed dryer, a mill, a lubricant blender and a tablet press. Granulation parameters were fixed in order to only examine the effect of drying parameters (filling time, drying time, air flow, drying air temperature) on the size distribution and moisture content of granules (both of the entire granulate and of size fractions). The wet granules were transferred either gravimetrically or pneumatically from the granulator exit to the fluid bed dryer. After a certain drying time, the moisture content reached an equilibrium. This drying time was found to depend on the applied airflow, drying air temperature and filling time. The moisture content of the granules decreased with an increasing drying time, airflow and drying temperature. Although smaller granules dried faster, the multimodal particle size distribution of the granules did not compromise uniform drying of the granules when the target moisture content was achieved. Extensive breakage of granules was observed during drying. Especially wet granules were prone to breakage and attrition during pneumatic transport, either in the wet transfer line or in the dry transfer line. Breakage and attrition of granules during transport and drying should be anticipated early on during process and formulation development by performing integrated experiments on the granulator

An experimentally validated simulation model for a four-stage spray dryer

DEFF Research Database (Denmark)

Petersen, Lars Norbert; Poulsen, Niels Kjølstad; Niemann, Hans Henrik

2017-01-01

mathematical model is an index-1 differential algebraic equation (DAE) model with 12 states, 9 inputs, 8 disturbances, and 30 parameters. The parameters in the model are identified from well-excited experimental data obtained from the industrialtype spray dryer. The simulated outputs ofthe model are validated...... is divided into four consecutive stages: a primary spray drying stage, two heated fluid bed stages, and a cooling fluid bed stage. Each of these stages in the model is assumed ideally mixed and the dynamics are described by mass- and energy balances. These balance equations are coupled with constitutive...... equations such as a thermodynamic model, the water evaporation rate, the heat transfer rates, and an equation for the stickiness of the powder (glass transition temperature). Laboratory data is used to model the equilibrium moisture content and the glass transition temperature of the powder. The resulting...

Organic leek seed production - securing seed quality

DEFF Research Database (Denmark)

Deleuran, Lise Christina; Boelt, Birte

2011-01-01

To maintain integrity in organic farming, availability of organically produced GM-free seed of varieties adapted to organic production systems is of vital impor-tance. Despite recent achievements, organic seed supply for a number of vegetable species is insufficient. Still, in many countries...... seeds. Tunnel production is a means of securing seed of high genetic purity and quality, and organic leek (Allium porrum L.) seed production was tested in tunnels in Denmark. The present trial focused on steckling size and in all years large stecklings had a positive effect on both seed yield...

Organic Leek Seed Production - Securing Seed Quality

DEFF Research Database (Denmark)

Deleuran, L C; Boelt, B

2011-01-01

To maintain integrity in organic farming, availability of organically produced GM-free seed of varieties adapted to organic production systems is of vital impor-tance. Despite recent achievements, organic seed supply for a number of vegetable species is insufficient. Still, in many countries...... seeds. Tunnel production is a means of securing seed of high genetic purity and quality, and organic leek (Allium porrum L.) seed production was tested in tunnels in Denmark. The present trial focused on steckling size and in all years large stecklings had a positive effect on both seed yield...

Empty seeds are not always bad: simultaneous effect of seed emptiness and masting on animal seed predation.

Directory of Open Access Journals (Sweden)

Ramón Perea

Full Text Available Seed masting and production of empty seeds have often been considered independently as different strategies to reduce seed predation by animals. Here, we integrate both phenomena within the whole assemblage of seed predators (both pre and post-dispersal and in two contrasting microsites (open vs. sheltered to improve our understanding of the factors controlling seed predation in a wind-dispersed tree (Ulmus laevis. In years with larger crop sizes more avian seed predators were attracted with an increase in the proportion of full seeds predated on the ground. However, for abundant crops, the presence of empty seeds decreased the proportion of full seeds predated. Empty seeds remained for a very long period in the tree, making location of full seeds more difficult for pre-dispersal predators and expanding the overall seed drop period at a very low cost (in dry biomass and allocation of C, N and P. Parthenocarpy (non-fertilized seeds was the main cause of seed emptiness whereas seed abortion was produced in low quantity. These aborted seeds fell prematurely and, thus, could not work as deceptive seeds. A proportion of 50% empty seeds significantly reduced ground seed predation by 26%. However, a high rate of parthenocarpy (beyond 50% empty seeds did not significantly reduce seed predation in comparison to 50% empty seeds. We also found a high variability and unpredictability in the production of empty seeds, both at tree and population level, making predator deception more effective. Open areas were especially important to facilitate seed survival since rodents (the main post-dispersal predators consumed seeds mostly under shrub cover. In elm trees parthenocarpy is a common event that might work as an adaptive strategy to reduce seed predation. Masting per se did not apparently reduce the overall proportion of seeds predated in this wind-dispersed tree, but kept great numbers of seeds unconsumed.

Construction of a flexible pilot dryer for products such as biofuels and iron ore pellets; Uppbyggnad av flexibel pilottork foer produkter som biobraenslen och jaernmalmspellets

Energy Technology Data Exchange (ETDEWEB)

Karlsson, Erik; Truedsson, Ida; Stenstroem, Stig

2009-02-15

Drying of different products is an operation that requires large amounts of energy in Sweden, a compilation from 2006 indicates a total use of over 32 TWh of thermal energy. A more energy efficient drying process can thus result in significant savings of energy for this process. The interest to use biofuels for heating purposes increases with increasing energy prices and thus also the interest to dewater and dry these products. Often an excess of low-value heat (flue gases, warm water etc.) is available and it would be desirable to use these streams for drying of different products. The goal in this project has been to carry out two subtasks: A Rebuild and modernise the old pilot dryer at the department so that it can be used for studies of drying kinetics for different products in a bed or as separate particles. B Perform a number of drying experiments with two representative bio-fuels which can be used for evaluation of different proposals for drying of these products. The results will mainly be of interest for companies handling biofuels in the forestry sector, for LKAB producing iron ore pellets and for manufacturers of industrial dryers. The constructed pilot dryer can be used for studies of drying kinetics of different types of products such as bark, wood chips, materials in the form of pellets such as iron ore pellets or wood pellets and foods. If the drying cell is designed so that fine particulate materials are not entrained with the gas flow, products such as municipal or industrial sludges can also be handled in the dryer. The results indicate specific energy use figures of between 2500 and 3000 kJ/kg evaporated water, both for different fractions of bark and independently if the origin of the bark was Vaeroe or Iggesund. The drying time to reach a dry matter content of 60 % for a bed with a thickness of 20 cm and an air velocity of 1 m/s is about 5000 seconds at an air temperature of 50 deg C. It increases to 15000 seconds to reach a dry matter content

Drying wood waste with a pulse combustion dryer

Energy Technology Data Exchange (ETDEWEB)

Buchkowski, A.G. [Spectrum Engineering Corp., Ltd., Peterborough, Ontario (Canada); Kitchen, J.A. [John A. Kitchen, Ltd., Hastings, Ontario (Canada)

1993-12-31

There is a vast amount of wood waste available to be used as an alternate fuel if its moisture could be reduced efficiently. Tests have been conducted to assess an industrial dryer using pulse combustion as a heating source for drying wood waste; specifically sawdust and pulverized wet hog fuel. Pulse combustion offers the advantage of high heat transfer, efficient combustion, and low NO{sub x} emissions. The material is injected into the exhaust gases in the tailpipe of the combustor which uses natural gas or propane as a fuel. The turbulence created by the pulsations enhance the drying process by reducing the boundary layer thicknesses. The materials is further dried in a rotary drum. The material has been dried without scorching or burning in tests where the inlet moisture content has been as high as 60% on a wet basis. The outlet moisture contents achieved have typically been 10%. Analysis of the test data and cost estimates of the equipment indicate that the pulse combustion drying system is at least comparable to existing systems in terms of operating costs, and offers very significant savings in capital costs. Testing with various other materials such as wood pulp, sludges and peat is continuing to further assess the equipment`s performance.

Seed-borne pathogens and electrical conductivity of soybean seeds

Directory of Open Access Journals (Sweden)

Adriana Luiza Wain-Tassi

2012-02-01

Full Text Available Adequate procedures to evaluate seed vigor are important. Regarding the electrical conductivity test (EC, the interference in the test results caused by seed-borne pathogens has not been clarified. This research was carried out to study the influence of Phomopsis sojae (Leh. and Colletotrichum dematium (Pers. ex Fr. Grove var. truncata (Schw. Arx. fungi on EC results. Soybean seeds (Glycine max L. were inoculated with those fungi using potato, agar and dextrose (PDA medium with manitol (-1.0 MPa and incubated for 20 h at 25 °C. The colony diameter, index of mycelial growth, seed water content, occurrence of seed-borne pathogens, physiological potential of the seeds, measured by germination and vigor tests (seed germination index, cold test, accelerated aging and electrical conductivity, and seedling field emergence were determined. The contents of K+, Ca2+, and Mg2+ in the seed and in the soaking solution were also determined. A complete 2 × 4 factorial design with two seed sizes (5.5 and 6.5 mm and four treatments (control, seeds incubated without fungi, seeds incubated with Phomopsis and seeds incubated with Colletotrichum were used with eight (5.5 mm large seeds and six (6.5 mm large seeds replications. All seeds submitted to PDA medium had their germination reduced in comparison to the control seeds. This reduction was also observed when seed vigor and leached ions were considered. The presence of Phomopsis sojae fungus in soybean seed samples submitted to the EC test may be the cause of misleading results.

Characterization and drying of caja bagasse (Spondias mombin L. in a tray dryer using a factorial planning

Directory of Open Access Journals (Sweden)

Andréia Souto da Silva

2012-03-01

Full Text Available The caja (Spondias mombin L. is used in the manufacture of ice-cream, jams, pulps, beverages being also consumed in natura. One of the most important procedures in food conservation is drying, considering that most fresh fruits contain approximately 80% of water. Food drying is used to obtain two basic aspects: (1 the economic factor; in the shipping and handling of the product; (2 at the manipulation; once dried and grinded, the material is rehydrated, at desirable levels, to formulate a new product as in ice cream, jams, yoghurts and drinks and may also be added to pasta, biscuits and other industrialized products. The aim of this study was to investigate the kinetics of caja bagasse drying in a fixed-bed tray dryer, using central composite factorial planning. The following factors were evaluated: temperature (55, 65 and 75 ºC, dryer inlet air velocity (3.2, 4.6 and 6.0 m.s-1 and cake thickness (0.8, 1.2 and 1.6 cm where the response of the considered variable was caja bagasse moisture content (b.s. and the results showed that the main effects and their interactions were significant at a 95% confidence level being the best condition obtained at temperature of 75 ºC, velocity of 6.0 m.s-1 and cake thickness of 0.8 cm.

Determination of stresses caused by fluctuation of acoustic load in the steam dryers of a BWR; Determinacion de esfuerzos originados por fluctuacion de carga acustica en los secadores de vapor de un reactor BWR

Energy Technology Data Exchange (ETDEWEB)

Centeno P, J.; Quezada G, S.; Prieto G, A.; Vazquez R, A.; Espinosa P, G. [Universidad Autonoma Metropolitana, Unidad Iztapalapa, Av. San Rafael Atlixco No. 186, Col. Vicentina, 09340 Mexico D. F. (Mexico); Nunez C, A., E-mail: javcuami26@hotmail.com [Comision Nacional de Seguridad Nuclear y Salvaguardias, Dr. Jose Ma. Barragan No. 779, Col. Narvarte, 03020 Mexico D. F. (Mexico)

2014-10-15

The extended power up-rate (EPU) in a nuclear power plant cause various problems in BWR components also in the steam system. This due to increased steam flow generated in the reactor and is conveyed to the turbine by the four main steam lines (MSL). One of the most serious problems is the generation of acoustic pressure loads in the metal structure of the steam dryer which eventually leads to fatigue failure and even the appearance of cracks, and in turn it causes loose parts that are entrained by the steam and transported in the MSL. This problem is due to the fluctuation of load acoustics caused by the union of the safety or relief valves (SRV) with the MSL, spreading through these to reach the reactor pressure vessel (RPV) where the effect of resonance of the acoustic wave is amplified and impacts directly in the supporting structure of the steam dryer, skirt and the panels where the mixture liquid-steam is dried, by centrifugation effect and runoff of liquid water. Efforts in the steam dryer operating conditions of EPU for two cases will be analyzed in this work, the first is before the installation of Acoustic Side Branch (ASB), and in the second case we consider the installation of said ASB in the standpipes of SRV. The analysis was performed with numerical experiments on a platform for computational fluid dynamics with virtual geometries previously designed based on the actual components of the reactor and steam system. The model to study is delimited by the top of the RPV, the steam dryer and a section of each of the four MSL with ten standpipes of SRV. With the obtained data and considering the mechanical-structural properties of the steam dryer material, we can evaluate the mechanical resistance to impacts by acoustic pressure load and its possible deformation or cracking. (Author)

某精细化工企业清洁生产审核实践研究%Cleaner Production Audit on A Fine Chemical Company

Institute of Scientific and Technical Information of China (English)

冯俊丽; 张时佳

2016-01-01

This paper takes the cleaner production of a company as example to expound the necessity and practical signifi-cance of carrying out cleaner production audit in fine chemical industry. According to eight existing issues of this company, the study provides practical low and high cost clean production project, totally 28 items. After calculating the economic, environmen-tal and social benefit of each project,the practical values of cleaner production audit to a company were pointed out, giving direc-tion of energy-saving emission reduction and low carbon development. This audit discusses the specific practice of cleaner pro-duction in fine chemical industry and it has guiding significance of practicing cleaner production in this domain.%以某企业的清洁生产审核为例,阐述分析精细化工行业开展清洁生产审核的必要性及实践意义.针对该企业存在的八方面问题,提出切实可行的无低费及中高费清洁生产方案共计28项,经核算各方案的经济、环境、社会效益,指出企业开展清洁生产审核的实际价值,为企业节能减排、低碳发展指明方向.本次审核初步探讨了清洁生产在精细化工行业的具体实践,对该行业清洁生产的践行具有一定的指导意义.

Solar dryers for a non-polluting removal of sewage sludge; Solartrockner fuer eine umweltfreundliche Klaerschlammentsorgung

Energy Technology Data Exchange (ETDEWEB)

Kos, Manfred [Lenze, Hameln (Germany)

2011-06-15

The acceptance of solar drying technology is depending on the quality of the produced dry goods. On local markets as well as for the export market dryed products can only compete if they can meet the quality standards of the food processing industry and consumers. A high added value for operators of solar dryers especially from developing countries can only be achieved if the goods can be exported. Dried sewage sludge shows to have an energy density corresponding to brown coal, burns however carbon dioxide neutrally compared with fossil fuels and grows continuously in water treatment plants on the outskirts of cities. (GL)

Airborne exposures associated with the typical use of an aerosol brake cleaner during vehicle repair work.

Science.gov (United States)

Fries, Michael; Williams, Pamela R D; Ovesen, Jerald; Maier, Andrew

2018-04-19

Many petroleum-based products are used for degreasing and cleaning purposes during vehicle maintenance and repairs. Although prior studies have evaluated chemical exposures associated with this type of work, most of these have focused on gasoline and exhaust emissions, with few samples collected solely during the use of an aerosol cleaning product. In this case study, we assess the type of airborne exposures that would be expected from the typical use of an aerosol brake cleaner during vehicle repair work. Eight exposure scenarios were evaluated over a two-day study in which the benzene content of the brake cleaner and potential for dilution ventilation and air flow varied. Both short-term (15 min) and task-based (≥1 hr) charcoal tube samples were collected in the breathing zone and adjacent work area and analyzed for total hydrocarbons (THCs), toluene, and benzene. The majority of personal (N = 48) and area (N = 47) samples had detectable levels of THC and toluene, but no detections of benzene were found. For the personal short-term samples, average airborne concentrations ranged from 3.1 - 61.5 ppm (13.8-217.5 mg/m 3 ) for THC and 2.2 - 44.0 ppm (8.2-162.5 mg/m 3 ) for toluene, depending on the scenario. Compared to the personal short-term samples, average concentrations were generally 2 to 3 times lower for the personal task-based samples and 2 to 5 times lower for the area short-term samples. The highest exposures occurred when the garage bay doors were closed, floor fan was turned off, or greatest amount of brake cleaner was used. These findings add to the limited dataset on this topic and can be used to bound or approximate worker or consumer exposures from use of aerosol cleaning products with similar compositions and use patterns.

Vocational training courses as an intervention on change of work practice among immigrant cleaners.

Science.gov (United States)

Jensen, Flemming W; Frydendall, Karen B; Flyvholm, Mari-Ann

2011-11-01

The aim of the study was to examine how knowledge and skills from vocational training courses on working techniques modified for immigrant cleaners are applied in practice and to identify factors that influence the implementation. The modifications of the standard course included language support with possibilities for translation and an extension of the duration of the course. The study is a prospective intervention study based on qualitative data. Data were collected as structured interviews and observations were carried out at the workplaces before and after the course. The study population included 31 immigrant cleaners from five different workplaces. Changes were observed in the use of working techniques (i.e., positioning of hands when using the floor mop). In some cases the use of the taught techniques was incorrect, partial, or only used part of the time. Interactions between individual factors (i.e., knowledge, awareness, capability, or work orientation) and environmental factors (i.e., equipment, time, workload, or physical surroundings) influenced the use of the techniques in practice. The course provided the participants with new working techniques through which some were able to reduce work related pain. However, with regard to incorrect and partial use of the working techniques, follow-up and post-training support is recommended. Copyright © 2011 Wiley Periodicals, Inc.

IMPACT OF AN OZONE GENERATOR AIR CLEANER ON STYRENE CONCENTRATIONS IN AN INDOOR AIR QUALITY RESEARCH CHAMBER

Science.gov (United States)

The paper gives results of an investigation of the impact of an ozone generator air cleaner on vapor-phase styrene concentrations in a full-scale indoor air quality test chamber. The time history of the concentrations of styrene and ozone is well predicted by a simulation model u...

Determinación del coeficiente global de transferencia de calor en secaderos rotativos de cáscara de limón Determination of global heat transfer coefficient in lemon peel rotary dryers

Directory of Open Access Journals (Sweden)

Marcos A. Golato

2005-12-01

Full Text Available En la bibliografía consultada no se encontraron trabajos de secado de cáscara de limón en secaderos rotativos. Se realizaron ensayos de medición en secaderos rotativos de cáscara de limón en una instalación agroindustrial del noroeste argentino. Se desarrolló un modelo matemático semiempírico mediante la resolución de los balances de materia y energía. Se obtuvo una correlación estadística para la predicción de los coeficientes globales volumétricos de transferencia de calor aparentes para secaderos rotativos de cáscara de limón.No papers on lemon peel drying in rotary dryers were actually found in the sources consulted. Measurement tests were carried out in the assessment of rotary dryer systems used to dehydrate lemon peel in an agroindustrial plant of Northwestern Argentina. A semiempirical mathematic model was developed solving mass and energy balances. A statistical correlation for predicting global heat transfer coefficient in rotary dryer lemon peel dehydration was obtained.

Does the informal seed system threaten cowpea seed health?

NARCIS (Netherlands)

Biemond, P.C.; Oguntade, O.; Lava Kumar, P.; Stomph, T.J.; Termorshuizen, A.J.; Struik, P.C.

2013-01-01

Most smallholder farmers in developing countries depend on an informal Seed System (SS) for their seed. The informal SS is often criticized because farmer-produced seed samples are not tested for seed health, thus accepting the risk of planting infected seeds. Here we aimed at assessing the quality

Biomass equipments. Dryers. Drying, crushing, agglomeration of agro-industrial products; Materiels pour la biomasse. Les secheurs, sechage, broyage, agglomeration de produits agro-industriels

Energy Technology Data Exchange (ETDEWEB)

Deur, O. [Promill (France)

1997-12-31

This paper describes the French Promill Company activity in the design and manufacturing of complete drying-crushing-agglomerating units for agro-industrial products (pulp of beet, lucerne, etc..). The paper focusses on the thermal and mechanical efficiency of the high temperature dryer and on the pulp granulating squeezer. (J.S.)

Performance of a Big Scale Green House Type Dryer for Coffee Drying Process

Directory of Open Access Journals (Sweden)

Sukrisno Widyotomo

2014-12-01

Full Text Available Dying is one of important steps in coffee processing to produce good quality. Greenhouse is one of artificial drying alternatives that potential for coffee drying method cause of cleans environmental friendly, renewable energy sources and chippers. Indonesian Coffee and Cocoa Research Institute has developed and testing a big scale greenhouse type dryer for fresh coffee cherries and wet parchment coffee drying process. Greenhouse has 24 m length, 18 m width, also 3 m high of the front side and 2 m high of the rear side. The maximum capacity of greenhouse is 40 tons fresh coffee cherries. Fiber Reinforced Plastic (FRP used as greenhouse roof that combined with I and C profile of steel. Fresh coffee cherries and wet parchment coffee from Robusta variety use as main materials in this research. The treatment of this research was 30 kg/m2, 60 kg/m2 and 90 kg/m2 for coffee density. String process has done by manual, two times a day in the morning and in the afternoon. As control, fresh coffee cherries and wet parchment coffee has dried by fully sun drying method. The result showed that a big scale greenhouse has heat drying efficiency between 29.9-58.2% depend on type and density of coffee treatments. On the full sunny day, greenhouse has produced maximum drying air temperature up to 52oC. In radiation cumulative level 4-5 kW-jam/m2 per day, 12.9-38.8 tons fresh coffee cherries or wet parchment coffee with 58-64% moisture content can be dried to 12% moisture content for 6 up to 14 days drying process. Slowly drying mechanism can be avoided negative effect to degradation of quality precursor compound. Capacity of the dryer can be raise and fungi can be reduce with application of controllable mechanical stirring in the greenhouse. Keywords: greenhouse, coffee, drying, quality

Efficiency of alfalfa seed processing with different seed purity

OpenAIRE

Đokić, Dragoslav; Stanisavljević, Rade; Terzić, Dragan; Milenković, Jasmina; Radivojević, Gordana; Koprivica, Ranko; Štrbanović, Ratibor

2015-01-01

The work was carried out analysis of the impact of the initial purity of raw alfalfa seed on the resulting amount of processed seed in the processing. Alfalfa is very important perennial forage legume which is used for fodder and seed production. Alfalfa seed is possible to achieve high yields and very good financial effects. To obtain the seed material with good characteristics complex machines for cleaning and sorting seeds are used. In the processing center of the Institute for forage crop...

Evaluation and comparing of natural and forced solar dryer for mint drying in Khuzestan province

Directory of Open Access Journals (Sweden)

J Habibi Asl

2017-05-01

Research Center during the years 2011-2013. Materials and Methods In this research an indirect cabinet solar dryer with three trays and grooved collector was constructed. To improve air convection, a chimney was mounted above the dryer. The dryer performance was evaluated by drying mint leaves in three levels of mass density of 2, 3, and 4 kg m-2 at two drying manners of natural and forced convection and compared with drying mint leaves in shade as the traditional method. Results and Discussion The results showed that total drying time required in different solar drier treatments was 3.5 to 15 h, while it was about 5 days in traditional method. Drying time in upper trays was more as the air flow decreased due to increase in mass density. Mean required drying time in forced convection was 29.7% less than that of natural convection. Maximum essences with 0.80% and 0.76% were belonged to "natural convection and 3kg m-2 mass density" and "forced convection and 4 kg m-2 mass density" treatments respectively, while minimum one with 0.30% was for "forced convection and 2 kg m-2 mass density" treatment. Also, the highest and lowest chlorophyll content with 8.51 and 4.18 mg ml-1 were measured in "natural convection and 3 kg m-2 mass density" and "forced convection and 4 kg m-2 mass density" treatments respectively. According to obtained results, 3 and 4 kg m-2 mass density can be suggested for natural and forced convection solar drying of mint leaves in Khuzestan condition respectively. Conclusions In order to reduce vegetable losses and increase Khuzestan vegetable producers income, indirect cabinet solar dryer for drying mint leaves in winter season, could be an appropriate option. For natural and forced convection drying methods, mass density of 3 and 4 kg m-2 is recommended respectively.

Saving oiled mangroves using a new non-dispersing shoreline cleaner

International Nuclear Information System (INIS)

Teas, H.J.; Lessard, R.R.; Canevari, G.P.; Brown, C.D.; Glenn, R.

1993-01-01

Mangroves are ranked as one of the most sensitive marine environments. If mangroves are oiled and no further action is taken, the probability of mortality to the trees is high. One of the ways that viscous spilled oil can kill mangroves is by covering the breathing ports, called lenticels (red mangroves) and pneumatophores (black mangroves), and asphyxiating them by preventing flow of oxygen from the atmosphere into the roots. Mangroves can also be killed by continuous inundation of their prop roots or pneumatophores for a period of ten days to two weeks, but they can survive lenticel covering by water for a few hours at high tide - so there appears to be some grace period during which lenticels can be nonfunctional and the plant can still survive once lenticel function is restored. This suggests that if oil is removed from the breathing ports during the early days after a spill, the lenticels may be able to restore oxygen delivery to the roots and spare the mangroves. Such oils are poorly removed by the washing of tidal waters or by water sprays alone. So a new shoreline cleaner (Corexit 9580), which was specially developed during the cleanup of the Valdez spill in Alaska, was tested to determine its ability to help loosen the oil so it can be washed away with water. Laboratory experiments using excised prop roots of red mangrove (Rhizophora mangle) were initially conducted to determine the feasibility of the approach. Subsequently experiments were carried out using about a hundred potted red mangroves at a test site in Florida. The prop roots, including the lenticels, were coated with a heavy oil (bunker C). After various periods of time, groups of oiled trees were treated with the shoreline cleaner to loosen and remove the oil deposit and then washed with seawater. The results showed that oiled trees could be saved by cleaning within seven days after oiling, indicating that the grace period after oiling extends for about one week

INVESTIGATION OF THE KINETICS OF DRYING SEEDS THISTLE IN VORTEX CHAMBER WITH MICROWAVE ENERGY SUPPLY

Directory of Open Access Journals (Sweden)

D. A. Kazartsev

2015-01-01

Full Text Available In the study of the current state of the theory, techniques and technologies for processing of milk thistle showed up a number of problems. One of those moments - the need to promptly provide quality and efficient process for drying seeds, but Russia has not produced special equipment for postharvest processing of seeds of milk thistle, and used for drying grain domestic appliances, represented mainly by mining and drum dryers, it is not suitable for thistle. This is due to the fact that, firstly, in the dewatering process is necessary to provide a relatively low final moisture drying product (5-6 %, and, secondly, to keep their beneficial substance in full, which imposes additional restrictions on the conditions of drying. One way of creating a new drying technology development and implementation in the industry of high-intensive devices with active hydrodynamic regimes with microwave energy supply, providing in many cases, higher technical and economic indicators. Therefore, the use of devices with swirling flow of heat-carrier for the intensification of the process of drying of dispersed materials is both theoretical interest and practical value. Microwave drying is based on the fact that the dielectric properties of water and dry food substances are different: the wet material is heated much faster than dry. During the microwave drying temperature wetter internal layers higher than the exterior more dehydrated (which creates a "right" - from the inner to the outer layers of the product - the gradient of moisture mass transfer is not realizable in any of the other known methods of drying. Milk thistle seeds have a unique composition: 25-32 % fatty oil, 15-17 % protein, 26 % fat, in the-soluble (B group and fat-soluble (A, D, E, K, F vitamins, mono- and disaccharides, macro- and trace elements (copper, zinc, selenium, dietary fiber and enzymes, mucus, up to 5 % (glucose, etc., phenolic compounds including flaviolignans 2-3% (silibinin

Physiological quality and seed respiration of primed Jatropha curcas seeds

Directory of Open Access Journals (Sweden)

Micheli Angelica Horbach

2017-11-01

Full Text Available ABSTRACT Seed deterioration is a natural and irreversible process. Nevertheless, seed priming with water and antioxidants can minimize oxidative damage in oilseeds, resulting in attenuation of seed deterioration. The objective of this assay was to evaluate seed priming on respiratory activity of Jatropha curcas submitted to accelerated aging. Seeds from two provenances (Janauba and Pedro J. Caballero were submitted to three priming treatments (control, immersion in deionized water, and with 750 µmol L-1 of ascorbic acid and treated for accelerated aging at 41 °C for 72 h. The results showed that the priming of J. curcas seeds promoted tolerance to accelerated aging. Primed seeds, with ascorbic acid from Janauba and deionized water from Pedro J. Caballero, resulted in a higher percentage of normal seedlings, and increased germination speed index and seed respiration. The decline of physiological quality of J. curcas seeds after accelerated aging is directly associated with a reduction in respiratory activity that is related to seed moisture content.

Identifying and Prioritizing Cleaner Production Strategies in Raw Materials’ Warehouse of Yazdbaf Textile Company in 2015

OpenAIRE

Mohammad Taghi Ghaneian; Raziye Montazerolfaraj; Hakime Selsele Vaziri; Mohammad Hassan Ehrampoush; Alireza Arsalan; Tahere Zarabie

2017-01-01

Introduction: Cleaner productions in textile industry is achieved by reducing water and chemicals’ consumption, saving energy, reducing production of air pollution and solid wastes, reducing toxicity and noise pollution through many solutions. The purpose of the present research was to apply Strengths, Weaknesses, Opportunities, Threats (SWOT) and Quality Systems Planning Matrix (QSPM) techniques in identifying and prioritizing production in raw materials’ warehouse of Yazdbaf Tex...

Evaluation of Wheat (Triticum aestivum, L. Seed Quality of Certified Seed and Farm-Saved Seed in Three Provinces of Iran

Directory of Open Access Journals (Sweden)

Khazaei Fardin

2016-06-01

Full Text Available The objective of this study was to study the seed quality aspects of wheat (Triticum aestivum L. and the extent of weed seed contamination present in wheat seeds produced in different regions of Iran. Four districts (cities, each including 12 fields (six certified seed fields and six farm-saved seed fields, were selected in each regions (provinces. One kilogram of the wheat seed sample was collected from each field for analysis in the laboratory. Wheat seeding was commonly done by farm-saved seed sourced from within the farm due to the high costs of certified seeds purchased from outside sources, followed by the low seed quality. The use of a farm-saved seed resulted in a higher germination rate and a lower mean time to germination compared with another system. The more positive temperatures experienced by mother plants could decrease the number of normal seedling and seedling length vigor index. Generally there was virtually no difference about physiological quality between certified seed and farm-saved seed sector that is related to lower quality of certified seed. The certified produced seeds had the lower number of weed seed, species and genus before and after cleaning. The highest seed purity and 1000 seed weight was obtained from the certified seed production system. The need for cleaning the farm-saved seed samples before sowing is one of the important findings of this survey.

Seed dormancy and seed longevity: from genetic variation to gene identification

NARCIS (Netherlands)

Nguyen, T.P.

2014-01-01

Seed dormancy and seed longevity are the most important survival traits in the soil seed bank. Both traits are induced during seed maturation and evolved to assure seed survival during environmental conditions that cannot support the regular course of life. Seed dormancy is related to the timing of

Influence of Fungicides Application and Seed Processing on Sunflower Seed Quality

OpenAIRE

Šimić, Branimir; Svitlica, Brankica; Ćosić, Jasenka; Andrić, Luka; Rozman, Vlatka; Postić, Jelena; Liović, Ivica

2009-01-01

The aim of the research was to determine influence of methods of seed processing and application of fungicides on mass of 1000 seeds, intergrowth energy and seed germination of sunflower hybrids ‘Favorit’ and ‘Apolon’ in 2005 and 2006. Selected untreated seeds of both sunflower hybrids (control) had a minimal mass of 1000 seeds (55-59 g), intergrowth energy (18-37 %) and seed germination (39-52 %). In both years of research maximal seed quality, mass of 1000 seeds (67-69 g), intergrowth energ...

Sudden changes in environmental conditions do not increase invasion risk in grassland

Science.gov (United States)

Ruprecht, Eszter; Fenesi, Annamária; Nijs, Ivan

2013-02-01

After direct habitat transformation, biological invasions are considered to be the second most important threat to biodiversity. A better understanding of the factors affecting invasion success in new areas is crucial, and may provide insight into potential control actions. We hypothesized that invasion risk increases in habitats undergoing a sudden change in the disturbance regime or environmental conditions. For testing this assumption we initiated a seed sowing experiment while introducing two novel treatments, mowing twice and fertilizer application, in two grassland sites (one dryer and one mesic) in Romania. The seeds of two invasive species, Solidago canadensis and Rudbeckia laciniata, and two resident natives of similar seed sizes, life-forms and strategies were sowed in treated and control plots, and seed germination, seedling establishment and growth were followed during four months. Contrary to our expectations, there was no difference in the treatment effects on seed germination and seedling establishment between species, while there was on seedling vigour of the larger seeded species in the dryer grassland site, where the native had a higher performance especially in increased nutrient conditions. Indifferently from applied treatments, invasive species had greater cumulative germination in the mesic site, while natives were far more successful in seedling establishment in the drier site. At the same time, seed size was found to be a very important factor explaining germination and establishment success, with large seeded species outperforming small seeded species in any circumstances. Our results call the attention upon management interventions in mesic, productive grassland sites opening colonization windows for the recruitment of those invasive species of which ecological requirements correspond to local environmental conditions.

Farmer’s seed sources and seed quality: 2. seed health

NARCIS (Netherlands)

Bishaw, Z.; Struik, P.C.; Gastel, van A.J.G.

2013-01-01

The study assessed the health quality of wheat (Triticum aestivum L.) and barley (Hordeum vulgare L.) seed samples collected from formal and informal sector in Ethiopia and Syria. In Ethiopia, several seed-borne fungi were found on wheat samples: Cochliobolus sativum, Fusarium avenaceum, F.

[Dynamics of seed rain of Tripterygium hypoglaucum and soil seed bank].

Science.gov (United States)

Zhang, Zhi-Wei; Wei, Yong-Sheng; Liu, Xiang; Su, Shu; Qu, Xian-You; Wang, Chang-Hua

2017-11-01

Tripterygium hypoglaucum is an endangered species in arid areas of Xiannvshan Chongqing, China. The dynamic characteristics of seed rain and soil seed bank of T. hypoglaucum were studied in this paper．Results showed that T. hypoglaucum years of mature seeds distribution number up to October; the seed rain occurred from the last ten-day of September to in the first ten-day of November and the peak of scattered seed rain concentrated in the October．The numbers of soil seed bank at 2-5 cm soil layer,mainly concentrated in the 1.5-3.5 m range. T. hypoglaucum seeds to the wind as a force for transmission, the transmission ability is strong, but in the process of natural reproduction, full mature seed rate is low, the soil seed bank seeds seed short-lived factors these were unfavorable for the natural reproduction of T. hypoglaucum population. Copyright© by the Chinese Pharmaceutical Association.

[Procedure of seed quality testing and seed grading standard of Prunus humilis].

Science.gov (United States)

Wen, Hao; Ren, Guang-Xi; Gao, Ya; Luo, Jun; Liu, Chun-Sheng; Li, Wei-Dong

2014-11-01

So far there exists no corresponding quality test procedures and grading standards for the seed of Prunus humilis, which is one of the important source of base of semen pruni. Therefor we set up test procedures that are adapt to characteristics of the P. humilis seed through the study of the test of sampling, seed purity, thousand-grain weight, seed moisture, seed viability and germination percentage. 50 cases of seed specimens of P. humilis tested. The related data were analyzed by cluster analysis. Through this research, the seed quality test procedure was developed, and the seed quality grading standard was formulated. The seed quality of each grade should meet the following requirements: for first grade seeds, germination percentage ≥ 68%, thousand-grain weight 383 g, purity ≥ 93%, seed moisture ≤ 5%; for second grade seeds, germination percentage ≥ 26%, thousand-grain weight ≥ 266 g, purity ≥ 73%, seed moisture ≤9%; for third grade seeds, germination percentage ≥ 10%, purity ≥ 50%, thousand-grain weight ≥ 08 g, seed moisture ≤ 13%.

Ammonium Laurate Surfactant for Cleaner Deposition of Carbon Nanotubes

Energy Technology Data Exchange (ETDEWEB)

Nilsson, Hanna M. [Department of Material Science and Engineering and ‡Department of Chemistry and Biochemistry, University of Maryland, College Park, Maryland 20742, United States; Meany, Brendan [Department of Material Science and Engineering and ‡Department of Chemistry and Biochemistry, University of Maryland, College Park, Maryland 20742, United States; Ticey, Jeremy [Department of Material Science and Engineering and ‡Department of Chemistry and Biochemistry, University of Maryland, College Park, Maryland 20742, United States; Sun, Chuan-Fu [Department of Material Science and Engineering and ‡Department of Chemistry and Biochemistry, University of Maryland, College Park, Maryland 20742, United States; Wang, YuHuang [Department of Material Science and Engineering and ‡Department of Chemistry and Biochemistry, University of Maryland, College Park, Maryland 20742, United States; Cumings, John [Department of Material Science and Engineering and ‡Department of Chemistry and Biochemistry, University of Maryland, College Park, Maryland 20742, United States

2015-06-15

Experiments probing the properties of individual carbon nanotubes (CNTs) and those measuring bulk composites show vastly different results. One major issue limiting the results is that the procedures required to separate and test CNTs introduce contamination that changes the properties of the CNT. These contamination residues often come from the resist used in lithographic processing and the surfactant used to suspend and deposit the CNTs, commonly sodium dodecyl sulfate (SDS). Here we present ammonium laurate (AL), a surfactant that has previously not been used for this application, which differs from SDS only by substitution of ionic constituents but shows vastly cleaner depositions. In addition, we show that compared to SDS, AL-suspended CNTs have greater shelf stability and more selective dispersion. These results are verified using transmission electron microscopy, atomic force microscopy, ζ-potential measurements, and Raman and absorption optical spectroscopy. This surfactant is simple to prepare, and the nanotube solutions require minimal sonication and centrifugation in order to outperform SDS.

Implementing cleaner production in an automotive company: an application of material input per unit of service tool to measure environmental and economic advantages

Directory of Open Access Journals (Sweden)

Geraldo Cardoso de Oliveira Neto

2017-09-01

Full Text Available Environmental impact reduction has been a growing concern of the automotive industry. One of the main challenges is to implement Cleaner Production as a tool to reduce environmental impacts and provide financial profits. The purpose of this article was to evaluate the environmental impact and economic gains by implementing Cleaner Production, using an unexplored approach, in a company of the automotive sector. The research approach used was a case study, carried out by observation and semi-structured surveys. The production process chosen was updated, so technologies were changed to reduce biotic and abiotic disposal. For the analysis of environmental impacts, the ‘Material Input Per Unit of Service’ tool (MIPS was used, in which data was used to calculate: annual net profit; return on investment (% and return on investment for a period. The results showed that Cleaner Production implementation focusing on changing technology in the production process caused a 75% reduction in environmental impact, and a 62.7% decrease in production costs. Although of this study considers only one case to test the procedure applicability, it can be easily repeated in other more complex systems, by merely making the necessary adjustments due to the complexity of the processes involved.

Unique concept results in 67% energy saving of dryer. Successful use of a NH3 heat pump for a McCain fried potato dryer; Uniek concept leidt tot een energiebesparing van 67% op de droger. NH3-warmtepomp succesvol toegepast op frietdroger van McCain

Energy Technology Data Exchange (ETDEWEB)

De Leeuw, M. [De Kleijn Energie Consulting, Druten (Netherlands)

2013-07-15

French fries producer McCain Foods installed in the summer of 2012 an ammonia heat pump for a fried potato dryer in Lelystad, Netherlands. After six months it appears that the installation operates without problems and with a very high efficiency [Dutch] Frietproducent McCain Foods installeerde in de zomer van 2012 een warmtepomp op de frietdroger in Lelystad. Na een half jaar kan geconstateerd worden dat de installatie zonder problemen en met een zeer hoog rendement draait.

Thin-layer drying of tomato (Lycopersicum esculentum Mill. cv. Rio Grande) slices in a convective hot air dryer

Energy Technology Data Exchange (ETDEWEB)

Demiray, Engin; Tulek, Yahya [Pamukkale University, Engineering Faculty, Department of Food Engineering, Kinikli, Denizli (Turkey)

2012-05-15

The effects of different drying temperatures on the drying kinetics of tomato slices were investigated using a cabinet-type dryer. The experimental drying data were fitted best to the to the Page and Modified Page models apart from other theoretical models to predict the drying kinetics. The effective moisture diffusivities varied from 1.015 x 10{sup -9} to 2.650 x 10{sup -9} m {sup 2} s {sup -1}over the temperature range studied, and activation energy was 22.981 kJ mol {sup -1}. (orig.)

Controlling in situ crystallization of pharmaceutical particles within the spray dryer.

Science.gov (United States)

Woo, Meng Wai; Lee, May Ginn; Shakiba, Soroush; Mansouri, Shahnaz

2017-11-01

Simultaneous solidification and in situ crystallization (or partial crystallization) of droplets within the drying chamber are commonly encountered in the spray drying of pharmaceuticals. The crystallinity developed will determine the functionality of the powder and its stability during storage. This review discusses strategies that can be used to control the in situ crystallization process. Areas covered: The premise of the strategies discussed focuses on the manipulation of the droplet drying rate relative to the timescale of crystallization. This can be undertaken by the control of the spray drying operation, by the use of volatile materials and by the inclusion of additives. Several predictive approaches for in situ crystallization control and new spray dryer configuration strategies are further discussed. Expert opinion: Most reports, hitherto, have focused on the crystallinity of the spray dried material or the development of crystallinity during storage. More mechanistic understanding of the in situ crystallization process during spray drying is required to guide product formulation trials. The key challenge will be in adapting the mechanistic approach to the myriad possible formulations in the pharmaceutical industry.

Long Term Effects on Risk Factors for Cardiovascular Disease after 12-Months of Aerobic Exercise Intervention - A Worksite RCT among Cleaners.

Directory of Open Access Journals (Sweden)

Mette Korshøj

Full Text Available Occupational groups exposed to high occupational physical activity have an increased risk for cardiovascular disease (CVD. This may be explained by the high relative aerobic workload. Enhanced cardiorespiratory fitness reduces the relative aerobic workload. Thus, the aim was to evaluate the 12-months effects of worksite aerobic exercise on risk factors for CVD among cleaners.One hundred and sixteen cleaners aged 18-65 years were randomized to a group performing aerobic exercise and a reference group receiving lectures. Outcomes were collected at baseline and after 12-months. A repeated measures 2×2 multi-adjusted mixed-model design was applied to compare the between-group differences using intention-to-treat analysis.Between-group differences (p<0.05 were found favouring the aerobic exercise group: cardiorespiratory fitness 2.15 (SE 1.03 mlO2/min/kg, aerobic workload -2.15 (SE 1.06 %HRR, resting HR -5.31 (SE 1.61 beats/min, high sensitive C-reactive protein -0.65 (SE 0.24 μg/ml. The blood pressure was unaltered. Stratified analyses on relative aerobic workload at baseline revealed that those with relative aerobic workloads ≥30% of HRR seems to impose a notable adverse effect on resting and ambulatory blood pressure.This long-term worksite aerobic exercise intervention among cleaners led to several beneficial effects, but also potential adverse effects among those with high relative aerobic workloads.Controlled-Trials.com ISRCTN86682076.

Variation of the height of the grain bed of an indirect solar bin dryer; Variacion de la altura del lecho del grano en un secador solar indirecto

Energy Technology Data Exchange (ETDEWEB)

Sima, Efrain; Alvarez, Gabriela; Garcia, Saul [CENIDET, Cuernavaca, Morelos (Mexico)

2000-07-01

This paper presents the effect of the variation of the size of the grain bed of an indirect solar bin dryer. This solar dryer was designed and built at the Instituto Tecnologico de Zacatepec and Sima performed the thermal evaluation. The solar bin dryer consists of a bin dryer of 0.92 m diameter and 1 m height (the maximum height of the grain bed is 0.6 m). a 2 m{sup 2} solar collector, a blower and an electronic card to control the inlet air flow of the bin. A load of 36 kg, 45 kg, 52 kg and 64 kg of corn were dried. The heights of the grain were 7.5 cm, 10 cm, 12.5 cm and 17 cm respectively. Solar radiation, inlet air velocity of the solar collector, pressure drop, grain temperature and humidity, ambient temperature and humidity of the drying air were recorded. The initial grain humidity was 27.2% and the final was 11.8%. [Spanish] En este trabajo se presenta el efecto de la variacion del lecho del grano en el proceso de secado de maiz, en un prototipo de secador solar de tipo indirecto. El secador fue disenado y construido en el Tecnologico de Zacatepec y evaluado por Sima, consta de una camara de secado de 0.92 m de diametro y una altura de 1 m. (la altura del lecho maximo de grano posible es de 0.6 m.), un colector solar con un area de 2 m{sup 2}, un extractor de aire y un control electronico para el flujo de aire. El secado de maiz se llevo a cabo con cargas de maiz de 36, 45, 52 y 64 kg. Las alturas en el lecho del grano fueron 7.5, 10, 12.5 y 17 cm. Para cada altura de lecho de grano se realizo una prueba. Durante cada prueba se realizaron mediciones de: radiacion solar, velocidad del aire a la entrada, caida de presion, temperatura del grano, humedad del grano, temperatura del aire ambiente, temperatura y humedad del aire de secado a la entrada y salida del secador. La humedad inicial del grano fue alrededor de 27.2% y la final de 11.8%.

Cleaner production options for reducing industrial waste: the case of batik industry in Malang, East Java-Indonesia

Science.gov (United States)

Sirait, M.

2018-01-01

The aim of this research is to conduct cleaner production options for improving the environmental performance during the production of batik industry, the case of UKM batik, Malang, East Java. Batik industry is one of small and medium textile industry which has contribution to economic growth in Malang. However, during production the batik, it generates wastewater that has potential to decrease the environmental performance. Wastewater from Celaket batik industry has BOD, COD, TSS, and pH level is far larger than the threshold of water quality standard as a result of use chemical substance during the dyes processing. In order to prevent generating wastewater, this study utilized cleaner production options, such as substitution of input material.Substitution of input material for dyes process was implemented by replacement chemical dyes (e.g.indigosol, nafthol, rapid) with natural dyes (e.g. Indigofero Tintoria). Modifying of technology/equipment was conducted by developing wastewater treatment equipment to reduce waste of batik production. The implementation of this strategy was carried out by changing input material from chemical dyes with natural dyes. The CP uptake could reduce significantly the environmental impact in term of reduction of COD, BOD, and TSS.

Size, physiological quality, and green seed occurrence influenced by seeding rate in soybeans

Directory of Open Access Journals (Sweden)

André Sampaio Ferreira

2017-05-01

Full Text Available The seeding rate influences the intraspecific competition, which might affect the development and quality of seeds in soybean. However, the impact of seeding rate on the physical and physiological qualities of soybean seeds needs to be better elucidated. This study aimed to evaluate the effects of soybean plant density on the seed size as well as the effects of the interaction between the plant density and seed size on the seed mass, green seed occurence, and physiological seed quality. The experiments were carried out in the growing seasons of the years 2013/14 and 2014/15 in a Latossolo Vermelho distroférrico, under a randomized complete block design, using the NK 7059 RR cultivar with six replications. Four plant densities (150, 300, 440, and 560 thousand viable seeds ha–1 were evaluated. After the classification of seeds into four sizes, using a set of sieves, a 4 ×4 factorial scheme was used for the statistical analysis of the four plant densities and four seed sizes. The seed samples were evaluated for the seed mass, green seed percentage, germination, and vigor. Under thermal and water stress during seed development, an increase in the seeding rate led to a reduction in the green seed occurrence and an increase in the seed size and mass. However, in the absence of thermal and water stress, the seed size and mass were not altered by the seeding rate and, there was no occurrence of green seeds.

Playing after work? Opportunities and challenges of a physical activity programme for female cleaners

DEFF Research Database (Denmark)

Lenneis, Verena; Pfister, Gertrud Ursula

2016-01-01

experience with sport and exercise and struggled with the high demands at work and a “second shift” at home. As a consequence, most participants found the training too time- and energy-consuming. We conclude that exercise programmes should preferably be conducted at the workplace and during working hours....... factors constrained and which supported participation. The interviews revealed a high degree of appreciation for the training but also pointed to a number of constraints which were embedded into the participants’ biographies and everyday lives as migrant cleaners in Denmark. Most women had no previous...

(Heckel) seeds

African Journals Online (AJOL)

UTILISATEUR

Garcinia kola seeds to six different hormonal pre-germination treatments. This consisted of ... Thus, seed dormancy in this case is not a coat- imposed .... development of the cultivation of the species. The cause .... Hormonal regulation of seed ...

Phenolics in the seed coat of wild soybean (Glycine soja) and their significance for seed hardness and seed germination.

Science.gov (United States)

Zhou, San; Sekizaki, Haruo; Yang, Zhihong; Sawa, Satoko; Pan, Jun

2010-10-27

Hardseededness in annual wild soybean (Glycine soja Sieb. Et Zucc.) is a valuable trait that affects the germination, viability, and quality of stored seeds. Two G. soja ecotypes native to Shandong Province of China have been used to identify the phenolics in the seed coat that correlate with the seed hardness and seed germination. Three major phenolics from the seed coat were isolated and identified as epicatechin, cyanidin 3-O-glucoside, and delphinidin 3-O-glucoside. Of the three phenolics, only the change of epicatechin exhibited a significant positive correlation with the change of hard seed percentages both under different water conditions during seed development and under different gas conditions during seed storage. Epicatechin also reveals a hormesis-like effect on the seed germination of G. soja. Epicatechin is suggested to be functionally related to coat-imposed hardseededness in G. soja.

Seed predators exert selection on the subindividual variation of seed size.

Science.gov (United States)

Sobral, M; Guitián, J; Guitián, P; Larrinaga, A R

2014-07-01

Subindividual variation among repeated organs in plants constitutes an overlooked level of variation in phenotypic selection studies, despite being a major component of phenotypic variation. Animals that interact with plants could be selective agents on subindividual variation. This study examines selective pressures exerted during post-dispersal seed predation and germination on the subindividual variation of seed size in hawthorn (Crataegus monogyna). With a seed offering experiment and a germination test, we estimated phenotypic selection differentials for average and subindividual variation of seed size due to seed predation and germination. Seed size affects germination, growth rate and the probability of an individual seed of escaping predation. Longer seeds showed higher germination rates, but this did not result in significant selection on phenotypes of the maternal trees. On the other hand, seed predators avoided wider seeds, and by doing so exerted phenotypic selection on adult average and subindividual variation of seed size. The detected selection on subindividual variation suggests that the levels of phenotypic variation within individual plants may be, at least partly, the adaptive consequence of animal-mediated selection. © 2013 German Botanical Society and The Royal Botanical Society of the Netherlands.

Producing the target seed: Seed collection, treatment, and storage

Science.gov (United States)

Robert P. Karrfalt

2011-01-01

The role of high quality seeds in producing target seedlings is reviewed. Basic seed handling and upgrading techniques are summarized. Current advances in seed science and technology as well as those on the horizon are discussed.

Hot seeding using large Y-123 seeds

International Nuclear Information System (INIS)

Scruggs, S J; Putman, P T; Zhou, Y X; Fang, H; Salama, K

2006-01-01

There are several motivations for increasing the diameter of melt textured single domain discs. The maximum magnetic field produced by a trapped field magnet is proportional to the radius of the sample. Furthermore, the availability of trapped field magnets with large diameter could enable their use in applications that have traditionally been considered to require wound electromagnets, such as beam bending magnets for particle accelerators and electric propulsion. We have investigated the possibility of using large area epitaxial growth instead of the conventional point nucleation growth mechanism. This process involves the use of large Y123 seeds for the purpose of increasing the maximum achievable Y123 single domain size. The hot seeding technique using large Y-123 seeds was employed to seed Y-123 samples. Trapped field measurements indicate that single domain samples were indeed grown by this technique. Microstructural evaluation indicates that growth can be characterized by a rapid nucleation followed by the usual peritectic grain growth which occurs when large seeds are used. Critical temperature measurements show that no local T c suppression occurs in the vicinity of the seed. This work supports the suggestion of using an iterative method for increasing the size of Y-123 single domains that can be grown

Report on seed born diseases in organic seed and propagation material

OpenAIRE

Micheloni, C.; Plakolm, G.; Schärer, H.

2007-01-01

The key questions which will be addressed in this report are: • Are seed born diseases an important factor that prevents seed companies from producing organic seeds and organic farmers from using them? • Which seed treatments are available in organic farming? Which treatments are or will be acceptable? To which degree are they effective? • Are the thresholds for seed born diseases different among Member States? Can this cause unfair competition among farmers and seed producers? • ...