WorldWideScience

Sample records for clam tapes pilippinarum

  1. Application of electron-beam irradiation on the production of salted and seasoned short-necked clam, Tapes Pilippinarum, for safe distribution

    Energy Technology Data Exchange (ETDEWEB)

    Kim, B.; Song, H.P.; Choe, J.H.; Jung, S. [Department of Animal Science and Biotechnology, Chungnam National University, Daejeon 305-764 (Korea, Republic of); Jang, A. [Quality Control and Utilization of Animal Products, National Institute of Animal Science, Suwon 441-706 (Korea, Republic of); Kim, Y.J. [Food Safety Research Division, Korea Food Research Institute, Seongnam 463-746 (Korea, Republic of); Jo, C. [Department of Animal Science and Biotechnology, Chungnam National University, Daejeon 305-764 (Korea, Republic of)], E-mail: cheorun@cnu.ac.kr

    2009-07-15

    Salted and seasoned short-necked clam (Tapes Philippinarum; SNC) and its major ingredients, red hot pepper powder, ginger, garlic and onion were irradiated at 0.5, 1, 2 and 5 kGy, respectively, and the microbiological and sensory quality were evaluated. The water activities of SNC and red pepper powder were 0.91 and 0.56, respectively, and others were higher than 0.97. The initial microbial populations of SNC were approximately 3.99, 4.38 and 2.22 log CFU/g for total aerobic bacteria, yeast and mold, and coliform bacteria. The highest contamination of total aerobic bacteria was detected from ground ginger among ingredients at 5.51 log CFU/g. Electron-beam irradiation (0, 0.5, 1, 2 and 5 kGy) significantly reduced the initial microbial level of SNC and its ingredients not only immediately after irradiation, but also during storage at 10 {sup o}C for 4 weeks (p<0.05). There was no adverse change of sensory score except for the color of onion irradiated at 5 kGy, which results in a lower score than control. From the results electron-beam irradiation is a useful tool to enhance the storage stability and safe distribution of SNC.

  2. Evaluation of 4-nonylphenol toxicity in the clam Tapes philippinarum

    International Nuclear Information System (INIS)

    Matozzo, Valerio; Deppieri, Martina; Oschino, Vanessa; Marin, M.G.

    2003-01-01

    Lethal and sub lethal effects of 4-nonylphenol (NP) were investigated in the clam Tapes philippinarum from the Lagoon of Venice. In a 96-h lethality test, bivalves were exposed to the following NP concentrations: 0, 0+acetone, .19, 0.38, 0.75, 1.5, and 3.0 mg NP/L. The 96-h LC 50 value was 1.12 mg P/L. No mortality was observed at 0.19 mg NP/L, whereas at 1.5 and 3.0 mg P/L both siphons and foot of clams were often cut-off, the animals being unable to withdraw them before shell closure, suggesting the possible narcotic effect of NP. Lower concentrations (0, 0+acetone, 0.025, 0.05, 0.1, nd 0.2 mg NP/L) were then used to evaluate sub lethal NP effects on clearance rate (CR), respiration rate (RR), scope for growth (SFG), and survival in ir. Following a 7-day exposure, decreased RRs were found at all NP concentrations tested. Significant decreases in the CR and SFG were only observed at the two highest NP concentrations (0.1 and 0.2 mg/L), with SFG reductions reaching 54% and 71%, respectively. Last, the highest concentrations tested significantly decreased the resistance of clams to exposure to air and enhanced the mortality rate. As the lowest effective NP concentrations are similar to environmentally realistic levels, a condition of potential risk for the well-being of clam populations in estuarine areas is highlighted

  3. Accumulation and elimination profiles of paralytic shellfish poison in the short-necked clam Tapes japonica fed with the toxic dinoflagellate Gymnodinium catenatum.

    Science.gov (United States)

    Samsur, Mohamad; Takatani, Tomohiro; Yamaguchi, Yasunaga; Sagara, Takefumi; Noguchi, Tamao; Arakawa, Osamu

    2007-02-01

    The paralytic shellfish poison (PSP)-producing dinoflagellate Gymnodinium catenatum (Gc) was fed to the short-necked clam Tapes japonica, and the accumulation, transformation and elimination profiles of PSP were investigated by means of high-performance liquid chromatography with postcolumn fluorescence derivatization (HPLC-FLD). The short-necked clams ingested most of the Gc cells (4 x 10(6) cells) supplied as a bolus at the beginning of the experiment, and accumulated a maximal amount of toxin (181 nmol/10 clams) after 12 hr. The rate of toxin accumulation at that time was 16%, which rapidly decreased thereafter. During the rearing period, a variation in toxin composition, derived presumably from the transformation of toxin analogues in the clams, was observed, including a reversal of the ratio of C2 to C1, and the appearance of carbamate (gonyautoxin (GTX) 2, 3) and decarbamoyl (dc) derivatives (decarbamoylsaxitoxin (dcSTX) and dcGTX2, 3), which were undetectable in Gc cells. The total amount of toxin contained in clams and residue (remaining Gc cells and/or excrement in the rearing tank) gradually declined, and only about 1% of the supplied toxin was detected at the end of the experiment.

  4. Comparison of two methods for the detection of hepatitis A virus in clam samples (Tapes spp.) by reverse transcription-nested PCR.

    Science.gov (United States)

    Suñén, Ester; Casas, Nerea; Moreno, Belén; Zigorraga, Carmen

    2004-03-01

    The detection of hepatitis A virus in shellfish by reverse transcription-nested polymerase chain reaction (RT-nested PCR) is hampered mainly by low levels of virus contamination and PCR inhibitors in shellfish. In this study, we focused on getting a rapid and sensitive processing procedure for the detection of HAV by RT-nested PCR in clam samples (Tapes spp.). Two previously developed processing methods for virus concentration in shellfish have been improved upon and compared. The first method involves acid adsorption, elution, polyethylene glycol (PEG) precipitation, chloroform extraction and PEG precipitation. The second method is based on elution with a glycine buffer at pH 10, chloroform extraction and concentration by ultracentrifugation. Final clam concentrates were processed by RNA extraction or immunomagnetic capture of viruses (IMC) before the RT-nested PCR reaction. Both methods of sample processing combined with the RNA extraction from the concentrates were very efficient when they were assayed in seeded and naturally contaminated samples. The results show that the first method was more effective in removal inhibitors and the second was simpler and faster. The IMC of HAV from clam concentrates processed by method 1 was revealed to be a very effective method of simultaneously removing residual PCR inhibitors and of concentrating the virus.

  5. Assessment of trace metal concentrations and human health risk in clam (Tapes decussatus) and mussel (Mytilus galloprovincialis) from the Homa Lagoon (Eastern Aegean Sea).

    Science.gov (United States)

    Bilgin, Mustafa; Uluturhan-Suzer, Esin

    2017-02-01

    Seasonal variations of trace metal concentrations (Hg, Cd, Pb, Cr, Zn, and Cu) were investigated in the hepatopancreas and soft tissues (remaining parts of bivalves such as gill, mantle, foot, and muscle) of Tapes decussatus and Mytilus galloprovincialis from the Homa Lagoon. The highest metal concentrations were recorded frequently in February and July in M. galloprovincialis and T. decussatus, respectively. Trace metal levels (except Zn) in the hepatopancreas were higher than those in soft tissue for both bivalves. The results showed that the mean concentrations of Hg, Cd, and Zn for M. galloprovincialis were higher compared to T. decussatus in both tissues. The metal concentrations in both bivalves from the Homa Lagoon were generally below the values of provisional tolerable weekly intake (PTWI) estimates, in terms of human health risk. According to hazard quotient (HQ), Cr values for both species and Cd values for only M. galloprovincialis were found greater than one. Also, total hazard index (THI) values were greater than one in both bivalves, having a potential risk for consumers.

  6. PCDD/F and dioxin-like PCB bioaccumulation by Manila clam from polluted areas of Venice lagoon (Italy).

    Science.gov (United States)

    Sfriso, Adriano; Facca, Chiara; Raccanelli, Stefano

    2014-01-01

    POP bioaccumulation pathways in the clam Tapes philippinarum were examined for two years from juveniles to adult size. Two polluted sites, one with sandy sediment, the other muddy were compared with a reference site characterized by low contamination levels. Juvenile clams coming from a hatchery were reared both on the sediment and in nets suspended at 30 cm from the bottom. POP changes in clam tissue were related to the concentrations recorded in sediments and in the particulate matter during the entire fattening period. Results provided interesting data on the relationships between environmental contamination and bioaccumulation. Contrary to studies on the decontamination times of the clams collected in polluted areas, this work investigates the preferential clam bioaccumulation pathways during growth under different environmental conditions. In general POP bioaccumulation resulted to be correlated to concentrations in SPM rather than in sediments and was higher in S-clams rather than in B-clams. Copyright © 2013 Elsevier Ltd. All rights reserved.

  7. PCDD/F and dioxin-like PCB bioaccumulation by Manila clam from polluted areas of Venice lagoon (Italy)

    International Nuclear Information System (INIS)

    Sfriso, Adriano; Facca, Chiara; Raccanelli, Stefano

    2014-01-01

    POP bioaccumulation pathways in the clam Tapes philippinarum were examined for two years from juveniles to adult size. Two polluted sites, one with sandy sediment, the other muddy were compared with a reference site characterized by low contamination levels. Juvenile clams coming from a hatchery were reared both on the sediment and in nets suspended at 30 cm from the bottom. POP changes in clam tissue were related to the concentrations recorded in sediments and in the particulate matter during the entire fattening period. Results provided interesting data on the relationships between environmental contamination and bioaccumulation. Contrary to studies on the decontamination times of the clams collected in polluted areas, this work investigates the preferential clam bioaccumulation pathways during growth under different environmental conditions. In general POP bioaccumulation resulted to be correlated to concentrations in SPM rather than in sediments and was higher in S-clams rather than in B-clams. -- Highlights: • PCDD/Fs and dioxin-like PCB accumulation in clam tissues during growth. • Muddy and sandy polluted areas. • How sediment and suspended matter contamination affect clam toxicity. • Clam toxicity and law limits. -- Clam bioaccumulation pathways in polluted areas

  8. IBM 3480 tape cartridge

    CERN Multimedia

    1984-01-01

    The 3480 tape format is a magnetic tape data storage format developed by IBM. The cartridge contains a single reel. IBM’s 3480 cartridge tape system sought to replace the traditional reels of magnetic tape in the computer center. Because of their speed, reliability, durability and low media cost, these tapes and tape drives are still in high demand. A hallmark of the genre is transferability. Tapes recorded with one tape drive are generally readable on another drive, even if the tape drives were built by different manufacturers.

  9. Tape transport mechanism

    International Nuclear Information System (INIS)

    Groh, E.F.; McDowell, W.; Modjeski, N.S.; Keefe, D.J.; Groer, P.

    1979-01-01

    A device is provided for transporting, in a stepwise manner, tape between a feed reel and takeup reel. An indexer moves across the normal path of the tape displacing it while the tape on the takeup reel side of the indexer is braked. After displacement, the takeup reel takes up the displaced tape while the tape on the feed reel side of the indexer is braked, providing stepwise tape transport in precise intervals determined by the amount of displacement caused by the indexer

  10. Bioaccumulation of gasoline in brackish green algae and popular clams

    Directory of Open Access Journals (Sweden)

    Gihan A. El-Shoubaky

    2016-03-01

    Full Text Available The green algae (Ulva lactuca and Enteromorpha clathrata and the clams (Tapes decussates and Venerupis aurea grow together in Timsah Lake, Suez Canal, Egypt. Our ultimate goal is to validate the bioaccumulation of gasoline in the marine organisms and their behavior after exposure to the pollutant, experimentally. These species were treated with a serial treatment of gasoline (1000, 4000, 16,000 and 64,000 μl in aquaria with brackish sea-water for 72 h. The tested green algae and clams were taken for an analysis of total hydrocarbon accumulation daily. The statistical analysis showed significant differences between the four species and also between the duration of exposure. The accumulation of gasoline in U. lactuca and E. clathrata reached their maximum after 48 h at 1000 and 4000 μl. The highest absorption was registered after 24 h only at 16,000 and at 64,000 μl. U. lactuca recorded complete mortality in 64,000 μl at 72 h whereas E. clathrata registered death at 48 h and 72 h in the same treatment. V. aurea was more sensitive than T. decussates. The accumulation of gasoline reached its maximum in V. aurea after only 24 h in the first treatment while it retarded to 48 h in T. decussates with a lesser accumulation. However, both clam species accumulated the highest amount of petroleum hydrocarbons during the first hour of exposure at the first treatment. In the third and fourth treatments, clams did not accumulate gasoline but began to dispose it from their tissues till it became less than that in the control. Mortality gradually increased with time in each treatment except the last one (64,000 μl in which 100% death of the specimens was observed. In general, the bioaccumulation of gasoline level was in a descending order as follows: U. lactuca > E. clathrata > V. aurea > T. decussates. Their behavior changed from accumulation to detoxification with time and with the increase in pollutant concentration. Generally, these

  11. Tape dig selv!

    DEFF Research Database (Denmark)

    Andersen, Bente Annie Sørine; Neergaard, Christian; Seest, Kristian

    Håndbog med over 50 tape-teknikker, hvor den klassiske hvide sportstape (Dream Tape) og den originale kinesiotape (Kinesio Tex Gold) bruges. Konkrete anvisninger og praktiske råd gives......Håndbog med over 50 tape-teknikker, hvor den klassiske hvide sportstape (Dream Tape) og den originale kinesiotape (Kinesio Tex Gold) bruges. Konkrete anvisninger og praktiske råd gives...

  12. Who's working on giant clam culture?

    OpenAIRE

    Vega, M.J.M.

    1990-01-01

    An examination is made of the literature on giant clam (Tridacna ) culture methods induced spawning, larvae, larval and post-larval rearing and socioeconomics. ASFA and the ICLARM library and professional staff collections were used for the search.

  13. The Role of Symbiotic Zooxanthellae on Giant Clam Nutrition

    OpenAIRE

    Ambariyanto

    1997-01-01

    Zooxanthellae, Symbiodinium sp, are single cell dinoflagellate algae known to live in association with many marine invertebrates such as hermatypic corals, sea anemones, jellyfish and giant clams (family Tridacnidae). In giant clams, these photosynthetic algae are located in a tubular system (known as Z tube system) which occurs within the clams. Apart from filter feeding, the nutrition of the clams is provided by zooxanthellae. These algae are capable of translocating part of their photosynt...

  14. Caught (Unfortunately) on Tape

    Science.gov (United States)

    Young, Jeffrey R.

    2009-01-01

    Recording class sessions so students can view them online is becoming routine on many campuses. But all that taping can lead to "uh-oh moments," such as when a professor's joke about the college dean ends up on YouTube, or a private comment to a student after class is inadvertently broadcast. Some lecture bloopers caught on tape are…

  15. The Clam Trail: Blending Science Education, Public Art, and Tourism

    Science.gov (United States)

    Muscio, Cara; Flimlin, Gef; Bushnell, Rick

    2011-01-01

    The Barnegat Bay Shellfish Restoration's Clam Trail is an award-winning scavenger hunt that combines science education, public art, and tourism. This family adventure has participants seeking out giant painted fiberglass clams, upweller clam nurseries, and points of interest in search of science facts to record on their forms. Upon returning these…

  16. Continuous cooling transformation behaviors of CLAM steel

    International Nuclear Information System (INIS)

    Wu, Qing-sheng; Zheng, Shu-hui; Huang, Qun-ying; Liu, Shao-jun; Han, Yang-yang

    2013-01-01

    The continuous cooling transformation (CCT) behaviors of CLAM (China Low Activation Martensitic) steel were studied, the CCT diagram was constructed, and the influence of cooling rates on the microstructures was also investigated. The microstructures were investigated using optical microscopy (OM) and microhardness tests were also carried out. The results showed that CLAM steel possessed high hardenability and there were ferrite and martensite transformation regions only. The maximum cooling rate to form ferrite microstructure was found to be 10–12 K/min. In order to obtain fully ferrite microstructure, the cooling rate should be lower than 1 K/min. The CCT diagram also gave relevant parameters such as the transformation temperatures, i.e., A c1 , A c3 , M s and M f were 1124 K, 1193 K, 705 K and 593 K, respectively. The diagram made it possible to predict the microstructures and properties of CLAM steel with different cooling rates

  17. The Imation 9840 Tape Cartridge

    CERN Multimedia

    It’s a 20 GB uncompressed center-load cartridge used in StorageTek T9840 tape drives. The tape is a Metal Particle (MP) tape suitable for use on all Oracle/Sun/StorageTek 9840 A, B, C and D drives. The 9840 tape has an archival life of 15-30 years.

  18. The effects of clam fishing on the properties of surface sediments in the lagoon of Venice, Italy

    Directory of Open Access Journals (Sweden)

    R. J. Aspen

    2004-01-01

    Full Text Available Harvesting of clams(Tapes philippinarum has important socio-economic and environmental implications for the Venice lagoon area, Italy. Clam harvesting disrupts the structure of benthic communities but the effects upon sediment stability and surface structure remain unclear. The effect of clam fishing on the sediment properties of the lagoon bed was investigated at two different sites, a heavily fished site (San Angelo and an infrequently fished site (San Giaccomo. Both sites were assessed for immediate impacts of fishing, using indicators of biogenic sediment stabilisation. Samples were taken at three points along three 100 m linear transects at each site prior to and post fishing. Paired samples were also taken parallel to each transect at a distance of 5m, to allow for temporal variation. Sediment stability, measured with a cohesive strength meter (CSM, was significantly higher at the less impacted site (F1,34 = 6.23, p a (chl a, colloidal-S carbohydrate and dry bulk density were observed on the transect after fishing but not adjacent to the fishing path. At the heavily impacted site, clam fishing by trawling had, in general, no significant effect on the biological and physical properties (although chl a did decrease significantly after fishing. The lack of a significant impact from fishing at the impacted site was attributed to the higher frequency of fishing occurring in this area. Hence, frequent fishing of the lagoon prevents establishment of biotic communities, preventing biostabilisation and thus reduces the stability of the surface sediment. Keywords: clam harvesting, erosion threshold, microphytobenthos, sediment, stability

  19. Paper Punch Tape

    CERN Multimedia

    Physicists coded and recorded their programs through series of holes on punch paper tape or on punched cards. It was popular in the 1970s due to its high throughput speed and low cost, paper tape was one of the original data storage methods for computers. Information was encoded in the distinct pattern of holes punched in the paper; the paper itself was oiled to facilitate being run through the reading mechanism and to prevent tears due to brittleness. Though the paper was cheap, it had low storage capacity (only a few dozen kilobytes per roll) and the machinery involved in punching the holes was quite expensive. Higher capacity alternatives, such as magnetic tape, has get developped.

  20. Analysis of trace elements in the shell of asari clams

    International Nuclear Information System (INIS)

    Arakawa, J.; Sakamoto, W.; Arai, N.; Yoshida, K.

    1999-01-01

    Strontium concentration in the shells of asari clams collected at different locations was analyzed by PIXE. The Sr concentration of external surface of shell umbo was ranged from 1000 to 3500 ppm for individuals. The Sr concentration of clams collected at Shirahama showed positive correlation with shell length, whereas clams collected at Maizuru did not show significant correlation. This result may be caused from the difference of the spawning seasons between two areas. (author)

  1. Continuous cooling transformation behaviors of CLAM steel

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Qing-sheng, E-mail: qingsheng.wu@fds.org.cn; Zheng, Shu-hui; Huang, Qun-ying; Liu, Shao-jun; Han, Yang-yang

    2013-11-15

    The continuous cooling transformation (CCT) behaviors of CLAM (China Low Activation Martensitic) steel were studied, the CCT diagram was constructed, and the influence of cooling rates on the microstructures was also investigated. The microstructures were investigated using optical microscopy (OM) and microhardness tests were also carried out. The results showed that CLAM steel possessed high hardenability and there were ferrite and martensite transformation regions only. The maximum cooling rate to form ferrite microstructure was found to be 10–12 K/min. In order to obtain fully ferrite microstructure, the cooling rate should be lower than 1 K/min. The CCT diagram also gave relevant parameters such as the transformation temperatures, i.e., A{sub c1}, A{sub c3}, M{sub s} and M{sub f} were 1124 K, 1193 K, 705 K and 593 K, respectively. The diagram made it possible to predict the microstructures and properties of CLAM steel with different cooling rates.

  2. Adhesive tape exfoliation

    DEFF Research Database (Denmark)

    Bohr, Jakob

    2015-01-01

    Single-crystal graphite can be cleaved by the use of an adhesive tape. This was also the initial route for obtaining graphene, a one-layer thick graphite slab. In this letter a few simple and fun considerations are presented in an attempt to shed some light on why this procedure is successful...

  3. Safety brake for tape reels

    Science.gov (United States)

    Carle, C. E.

    1977-01-01

    All-mechanical device senses end of tape and stops reel, even in event of electronic system failure. Assembly includes stop to prevent brake from overriding tape. Recentering mechanism returns brake to neutral position after torque is removed from reels.

  4. Tamper tape seals

    International Nuclear Information System (INIS)

    Wright, B.W.; Undem, H.A.

    1994-07-01

    Tamper tapes are appealing for many applications due to their ease of use and relative robustness. Applications include seals for temporary area denial, protection of sensitive equipment, chain-of-custody audit trails, and inventory control practices. A next generation of adhesive tamper tapes is being developed that combines the best features of commercially available devices with additional state-of-the-art features in tamper indication, tamper-resistance, and counterfeit-resistance. The additional features are based on U.S. Department of Energy (DOE) research and development (R ampersand D) activities that were originally associated with preparations for the Strategic Arms Reduction Treaty (START). New features include rapid-set, chemical-cure adhesive systems that allow user-friendly application and layered levels of counterfeit-resistance based on unique open-quotes fingerprintclose quotes characteristics that can be accessed as desired

  5. Teaching with MARC Tapes

    Directory of Open Access Journals (Sweden)

    Pauline Atherton

    1970-03-01

    Full Text Available A computer based laboratory for library science students to use in class assignments and for independent projects has been developed and used for one year at Syracuse University. MARC Pilot Project tapes formed the data base. Different computer programs and various samples of the MARC file (48,POO records, approx. were used for search and retrieval operations. Data bases, programs, and seven different class assignments are described and evaluated for their impact on library education in gen- eral and individual students and faculty in particular.

  6. Application for the Tape Station

    CERN Document Server

    Solero, A

    2003-01-01

    The Tape Station is used as an Isolde facility to observe the variations of intensity and the lifespan of certain isotopes. A Siemens Simatic FM-352-5 module controls the Tape Station in a PLC system then a DSC controls the PLC, which will be controlled the Tape station program. During the Isolde consolidation project, the Tape Station has been rebuilt, and the control system has been fully integrated in the PS control. Finally, a new application has been written in JAVA Development kit 1.4 and the PS Java environment. The main purpose of this note is to explain how to use this program.

  7. Razor clam to RoboClam: burrowing drag reduction mechanisms and their robotic adaptation

    International Nuclear Information System (INIS)

    Winter, A G; V; Dorsch, D S; Slocum, A H; Hosoi, A E; Deits, R L H

    2014-01-01

    Estimates based on the strength, size, and shape of the Atlantic razor clam (Ensis directus) indicate that the animal's burrow depth should be physically limited to a few centimeters; yet razor clams can dig as deep as 70 cm. By measuring soil deformations around burrowing E. directus, we have found the animal reduces drag by contracting its valves to initially fail, and then fluidize, the surrounding substrate. The characteristic contraction time to achieve fluidization can be calculated directly from soil properties. The geometry of the fluidized zone is dictated by two commonly-measured geotechnical parameters: coefficient of lateral earth pressure and friction angle. Calculations using full ranges for both parameters indicate that the fluidized zone is a local effect, occurring between 1–5 body radii away from the animal. The energy associated with motion through fluidized substrate—characterized by a depth-independent density and viscosity—scales linearly with depth. In contrast, moving through static soil requires energy that scales with depth squared. For E. directus, this translates to a 10X reduction in the energy required to reach observed burrow depths. For engineers, localized fluidization offers a mechanically simple and purely kinematic method to dramatically reduce energy costs associated with digging. This concept is demonstrated with RoboClam, an E. directus-inspired robot. Using a genetic algorithm to find optimal digging kinematics, RoboClam has achieved localized fluidization burrowing performance comparable to that of the animal, with a linear energy-depth relationship, in both idealized granular glass beads and E. directus' native cohesive mudflat habitat. (paper)

  8. BALLISTIC RESISTANT ARTICLES COMPRISING TAPES

    NARCIS (Netherlands)

    VAN DER EEM, JORIS; HARINGS, JULES; JANSE, GERARDUS; TJADEN, HENDRIK

    2015-01-01

    The invention pertains to a ballistic-resistant moulded article comprising a compressed stack of sheets comprising reinforcing tapes having a tensile strength of at least 1.0 GPa, a tensile modulus of at least 40 GPa, and a tensile energy-to-break of at least 15 J/g, the direction of the tapes

  9. Centrally managed tapes at DESY

    International Nuclear Information System (INIS)

    Hell, O.

    1994-01-01

    Tapes at DESY are managed by the computer center and thus offer virtually unlimited storage space to the DESY computer center users. This paper describes the most recent version of the DESY tape management system, its predecessors having been in service for many years

  10. Reproduction and recruitment patterns of the surf clam Donax serra ...

    African Journals Online (AJOL)

    Reproduction and recruitment patterns of the surf clam Donax serra (Bivalvia, Donacidae) on two ... Keywords: condition index, Donax serra, histology, Namibia, recruitment, reproduction, sandy beach ecology ... AJOL African Journals Online.

  11. Asteroid Composite Tape

    Science.gov (United States)

    1998-07-01

    This is a composite tape showing 10 short segments primarily about asteroids. The segments have short introductory slides, which include brief descriptions about the shots. The segments are: (1) Radar movie of asteroid 1620 Geographos; (2) Animation of the trajectories of Toutatis and Earth (3) Animation of a landing on Toutatis; (4) Simulated encounter of an asteroid with Earth, includes a simulated impact trajectory; (5) An animated overview of the Manrover vehicle; (6) The Near Earth Asteroid Tracking project, includes a photograph of USAF Station in Hawaii, and animation of Earth approaching 4179 Toutatis and the asteroid Gaspara; (7) live video of the anchor tests of the Champoleon anchoring apparatus; (8) a second live video of the Champoleon anchor tests showing anchoring spikes, and collision rings; (9) An animated segment with narration about the Stardust mission with sound, which describes the mission to fly close to a comet, and capture cometary material for return to Earth; (10) live video of the drop test of a Stardust replica from a hot air balloon; this includes sound but is not narrated.

  12. Low cycle fatigue properties of CLAM steel at 823 K

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Xue [Institute of Metal Research, Chinese Academy of Sciences, 72 Wenhua Road, Shenyang 110016 (China); University of Chinese Academy of Sciences, 19 Yuquan Road, Beijing 100049 (China); Huang, Lixin [Institute of Metal Research, Chinese Academy of Sciences, 72 Wenhua Road, Shenyang 110016 (China); State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004 (China); Yan, Wei; Wang, Wei [Institute of Metal Research, Chinese Academy of Sciences, 72 Wenhua Road, Shenyang 110016 (China); Sha, Wei [School of Planning, Architecture and Civil Engineering, Queen' s University Belfast, Belfast BT9 5AG (United Kingdom); Shan, Yiyin, E-mail: yyshan@imr.ac.cn [Institute of Metal Research, Chinese Academy of Sciences, 72 Wenhua Road, Shenyang 110016 (China); Yang, Ke, E-mail: kyang@imr.ac.cn [Institute of Metal Research, Chinese Academy of Sciences, 72 Wenhua Road, Shenyang 110016 (China)

    2014-09-08

    China Low Activation Martensitic (CLAM) steel is considered to be the main candidate material for the first wall components of future fusion reactors in China. In this paper, the low cycle fatigue (LCF) behavior of CLAM steel is studied under fully reversed tension–compression loading at 823 K in air. Total strain amplitude was controlled from 0.14% to 1.8% with a constant strain rate of 2.4×10{sup −3} s{sup −1}. The corresponding plastic strain amplitude ranged from 0.023% to 1.613%. The CLAM steel displayed continuous softening to failure at 823 K. The relationship between strain, stress and fatigue life was obtained using the parameters obtained from fatigue tests. The LCF properties of CLAM steel at 823 K followed Coffin–Manson relationship. Furthermore, irregular serration was observed on the stress–strain hysteresis loops of CLAM steel tested with the total strain amplitude of 0.45–1.8%, which was attributed to the dynamic strain aging (DSA) effect. During continuous cyclic deformation, the microstructure and precipitate distribution of CLAM steel changed gradually. Many tempered martensitic laths were decomposed into subgrains, and the size and number of M{sub 23}C{sub 6} carbide and MX carbonitride precipitates decreased with the increase of total strain amplitude. The response cyclic stress promoted the recovery of martensitic lath, while the thermal activation mainly played an important role on the growth of precipitates in CLAM steel at 823 K. In order to have a better understanding of high-temperature LCF behavior, the potential mechanisms controlling stress–strain response, DSA phenomenon and microstructure changes have also been evaluated.

  13. String and Sticky Tape Experiments.

    Science.gov (United States)

    Edge, R. D., Ed.

    1979-01-01

    Explains how to demonstrate the fundamentals of one dimensional kinematics such as Newton's third law of motion, and collision between bodies, using simple materials of marbles, strings, sticky tape, drinking straws, and rubber bands. (GA)

  14. Tape casting fluorinated YBC123

    International Nuclear Information System (INIS)

    Taylor, J.A.T.; Luke, D.M.; Whiteley, B.A.

    1991-01-01

    Tape casting the superconducting Ba-Y-Cu oxide was accomplished by several laboratories and show promise for being a versatile forming technique. The major problem is low current density, probably due to lack of grain alignment and grain boundary related weak links. The latter problem may be due to formation of carbonates and hydroxides during binder burnout. Preliminary work done at Alfred shows that a bimodal powder size distribution displays significant alignment after tape casting and that F treated powder is resistant to attack by steam at 100C. Such corrosion resistant powder cast as form tape should survive the binder burnout without the detrimental grain boundary phases that develop from reaction of the superconducting phase, steam and carbon dioxide. This paper presents the results of an investigation of tape casting fluorinated powder with a bimodal size distribution

  15. Tape Storage and CRC Protection

    CERN Document Server

    Ha, Karel

    2014-01-01

    Over 100 Petabytes of data is stored on several kind of physical support, namely disks and tapes. Data on any physical support or traveling on a data link (network, fibre channel...) can be subject to silent data corruption. A possible improvement is introducing end-to-end data integrity from the filesystem down to the tape layer. For the tape back-end it can be done by using Logical Block Protection, which computes and compares CRC checksum of every single block of data. During my work, I improved on-the-fly CRC calculation for the tape storage system, which was achieved by introducing a multithreaded implementation - a technique applicable to arbitrary CRC algorithm. Finally, I per...

  16. Ancient Clam Gardens Increased Shellfish Production: Adaptive Strategies from the Past Can Inform Food Security Today

    Science.gov (United States)

    Groesbeck, Amy S.; Rowell, Kirsten; Lepofsky, Dana; Salomon, Anne K.

    2014-01-01

    Maintaining food production while sustaining productive ecosystems is among the central challenges of our time, yet, it has been for millennia. Ancient clam gardens, intertidal rock-walled terraces constructed by humans during the late Holocene, are thought to have improved the growing conditions for clams. We tested this hypothesis by comparing the beach slope, intertidal height, and biomass and density of bivalves at replicate clam garden and non-walled clam beaches in British Columbia, Canada. We also quantified the variation in growth and survival rates of littleneck clams (Leukoma staminea) we experimentally transplanted across these two beach types. We found that clam gardens had significantly shallower slopes than non-walled beaches and greater densities of L. staminea and Saxidomus giganteus, particularly at smaller size classes. Overall, clam gardens contained 4 times as many butter clams and over twice as many littleneck clams relative to non-walled beaches. As predicted, this relationship varied as a function of intertidal height, whereby clam density and biomass tended to be greater in clam gardens compared to non-walled beaches at relatively higher intertidal heights. Transplanted juvenile L. staminea grew 1.7 times faster and smaller size classes were more likely to survive in clam gardens than non-walled beaches, specifically at the top and bottom of beaches. Consequently, we provide strong evidence that ancient clam gardens likely increased clam productivity by altering the slope of soft-sediment beaches, expanding optimal intertidal clam habitat, thereby enhancing growing conditions for clams. These results reveal how ancient shellfish aquaculture practices may have supported food security strategies in the past and provide insight into tools for the conservation, management, and governance of intertidal seascapes today. PMID:24618748

  17. Calculating the Contribution of Zooxanthellae to Giant Clams Respiration Energy Requirements

    OpenAIRE

    Ambariyanto

    2002-01-01

    Giant clams (Tridacnidae) are known to live in association with photosynthetic single cell dinoflagellate algae commonly called zooxanthellae. These algae which can be found in the mantle of the clams are capable of transferring part of their photosynthates which become an important source of energy to the host ( apart from filter feeding activity). In order to understand the basic biological processes of the giant clams , the contribution of zooxanthellae to the clam's energy requirement nee...

  18. Toxicity of a traditional molluscicide to asian clam veligers

    Science.gov (United States)

    Layhee, Megan J.; ,; Miho Yoshioka,; Bahram Farokhkish,; ,; Gross, Jackson A.; Sepulveda, Adam J.

    2014-01-01

    Aquaculture and hatchery industries are in need of effective control methods to reduce the risk of spreading aquatic invasive species, such as the Asian clam Corbicula fluminea, through aquaculture and hatchery activities. The planktonic nature of Asian clam veligers enables this life stage to enter water-based infrastructure undetected, including hatchery trucks used to stock fish. Once in hatchery trucks, veligers can disperse overland and establish in previously uninvaded habitats. As a result, there is a need to develop techniques that result in veliger mortality but do not harm fish. In September 2012, we conducted laboratory trials to determine if a molluscicide (750 mg/L potassium chloride and 25 mg/L formalin) commonly used to kill zebra mussel (Dreissena polymorpha) veligers in hatchery trucks can also effectively kill Asian clam veligers. We exposed Asian clam veligers to this molluscicide for 1, 3, and 5 h in each of two water types: deionized water and filtered lake water. We found ,20% mortality at the 1-h exposure period and 100% mortality at both the 3-h and 5-h exposure periods, regardless of water type. This laboratory study represents an important step toward reducing the spread of Asian clams by aquaculture facilities.

  19. Effect of low salinity on the yellow clam Mesodesma mactroides

    Directory of Open Access Journals (Sweden)

    YBM. Carvalho

    Full Text Available The aim of this study was to determine the lethal salinity (LC50 for the yellow clam Mesodesma mactroides (Bivalvia: Mesodesmatidae and identify histopathological alterations that could be used to diagnose structural changes in clam tissue. Clams in two size classes (adults and juveniles were placed in 10 L chambers and exposed to salinities of 35, 30, 25, 20, 15, 10, and 5 g/L. There were triplicate chambers with seven clams each for each salinity. The LC50 values for a 48 h exposure were 6.5 g/L and 5.7 g/L for adults and juveniles, respectively. For a 96 h exposure, the LC50 values were 10.5 g/L for adults and 8.8 g/L for juveniles. The histological examination of yellow clams exposed to 10 g/L for 96 h showed intercellular oedema and necrotic foci in the epithelium of the digestive gland and occlusion of the lumen of the digestive gland. In conclusion, M. mactroides can be characterised as a moderately euryhaline species, tolerating salinities from 35 to 15 g/L.

  20. Heavy metal determinations in algae and clams and their possible employment for assessing the sea water quality criteria.

    Science.gov (United States)

    Locatelli, C; Fabbri, D; Torsi, G

    2001-01-01

    An empirical criterion for a possible classification of sea water quality is proposed. It is based on the knowledge of metal content in algae (Ulva Rigida) and clams (Tapes Philippinarum), two species present in marine ecosystems. The elements considered are Hg, Cu, Pb, Cd, Zn. The analytical technique employed is Differential Pulse Anodic Stripping Voltammetry (DPASV) in the case of Cu, Pb, Cd, Zn, while the determination of mercury is obtained by the Cold Vapour Atomic Absorption Spectroscopy (CV-AAS) technique with SnCl2 as reducing agent. The analytical procedure has been verified on three standard reference materials: Sea Water BCR-CRM 403, Ulva Lactuca BCR-CRM 279 and Mussel Tissue BCR-CRM 278. For all the elements, in addition to detection limits, accuracy and precision are given: the former, expressed as relative error (e), and the latter, expressed as relative standard deviation (Sr), were in all cases lower than 6%.

  1. Superconducting flat tape cable magnet

    Science.gov (United States)

    Takayasu, Makoto

    2015-08-11

    A method for winding a coil magnet with the stacked tape cables, and a coil so wound. The winding process is controlled and various shape coils can be wound by twisting about the longitudinal axis of the cable and bending following the easy bend direction during winding, so that sharp local bending can be obtained by adjusting the twist pitch. Stack-tape cable is twisted while being wound, instead of being twisted in a straight configuration and then wound. In certain embodiments, the straight length should be half of the cable twist-pitch or a multiple of it.

  2. Tape write-efficiency improvements in CASTOR

    International Nuclear Information System (INIS)

    Murray, S; Bahyl, V; Cancio, G; Cano, E; Lo Presti, G; Lo Re, G; Ponce, S; Kotlyar, V

    2012-01-01

    The CERN Advanced STORage manager (CASTOR) is used to archive to tape the physics data of past and present physics experiments. For reasons of physical storage space, all of the tape resident data in CASTOR are repacked onto higher density tapes approximately every two years. Improving the performance of writing files smaller than 2GB to tape is essential in order to keep the time needed to repack all of the tape resident data within a period of no more than 1 year. This paper reports on the solution to writing efficiently to tape that is currently in its early deployment phases at CERN.

  3. Tape edge study in a linear tape drive with single-flanged guides

    International Nuclear Information System (INIS)

    Goldade, A.V.; Bhushan, Bharat

    2004-01-01

    Improved tape guiding and tape dimensional stability are essential for magnetic tape linear recoding formats to take advantage of vastly increased track density and thereby achieve higher storage capacities. Tape guiding is dependent on numerous parameters, such as type of the guides and tape path geometry, quality of virgin tape edge, drive operating parameters (e.g., tape speed and tape tension), mechanical properties of the tape, and tape geometry (e.g., cupping and curvature). The objective of the present study is to evaluate guiding and tribological performance of single-flanged guides with porous air bearings in a linear tape drive. A comparison of guiding performance of the dual flanged stationary guides and single-flanged guides with porous air bearings is performed. The effect of tape path geometry, drive operating conditions (speed and tension) and tape edge quality of factory-slit tapes on tape guiding are evaluated during short-term tests. A lateral force measurement technique is used to measure the force exerted by the tape edge on the guide flange. A technique for the lateral tape motion measurement is used to study the effect of continuous sliding on tape guiding. Wear tests up to 5000 cycles are conducted and coefficient of friction and lateral tape motion are monitored to study the effect of drive operating conditions (speed and tension), edge quality of factory-slit tapes and tape thickness on tape guiding. Optical microscopy, atomic force microscopy and scanning electron microscopy are employed to study and quantify the quality of tape edge

  4. Effects of predation by sea ducks on clam abundance in soft-bottom intertidal habitats

    Science.gov (United States)

    Lewis, Tyler; Esler, Daniel N.; Boyd, W. Sean

    2007-01-01

    Recent studies have documented strong, top-down predation effects of sea ducks on mussel populations in rocky intertidal communities. However, the impact of these gregarious predators in soft-bottom communities has been largely unexplored. We evaluated effects of predation by wintering surf scoters Melanitta perspicillata and white-winged scoters M. fusca on clam populations in soft-bottom intertidal habitats of the Strait of Georgia, British Columbia. Specifically, we documented spatial and temporal variation in clam density (clams m–2), scoter diet composition, and the consequences of scoter predation on clam abundance. Of the 3 most numerous clams, Manila clams Venerupis philippinarum and varnish clams Nuttallia obscurata were the primary prey items of both scoter species, while clams of the genus Macoma were rarely consumed by scoters. Between scoter arrival in the fall and departure in the spring, Manila clams decreased in density at most sample sites, while varnish clam densities did not change or declined slightly. Our estimates of numbers of clams consumed by scoters accounted for most of the observed declines in combined abundance of Manila and varnish clams, despite the presence of numerous other vertebrate and invertebrate species known to consume clams. For Macoma spp., we detected an over-winter increase in density, presumably due to growth of clams too small to be retained by our sieve (<5 mm) during fall sampling, in addition to the lack of predation pressure by scoters. These results illustrate the strong predation potential of scoters in soft-bottom intertidal habitats, as well as their potentially important role in shaping community structure.

  5. Photosymbiotic giant clams are transformers of solar flux.

    Science.gov (United States)

    Holt, Amanda L; Vahidinia, Sanaz; Gagnon, Yakir Luc; Morse, Daniel E; Sweeney, Alison M

    2014-12-06

    'Giant' tridacnid clams have evolved a three-dimensional, spatially efficient, photodamage-preventing system for photosymbiosis. We discovered that the mantle tissue of giant clams, which harbours symbiotic nutrition-providing microalgae, contains a layer of iridescent cells called iridocytes that serve to distribute photosynthetically productive wavelengths by lateral and forward-scattering of light into the tissue while back-reflecting non-productive wavelengths with a Bragg mirror. The wavelength- and angle-dependent scattering from the iridocytes is geometrically coupled to the vertically pillared microalgae, resulting in an even re-distribution of the incoming light along the sides of the pillars, thus enabling photosynthesis deep in the tissue. There is a physical analogy between the evolved function of the clam system and an electric transformer, which changes energy flux per area in a system while conserving total energy. At incident light levels found on shallow coral reefs, this arrangement may allow algae within the clam system to both efficiently use all incident solar energy and avoid the photodamage and efficiency losses due to non-photochemical quenching that occur in the reef-building coral photosymbiosis. Both intra-tissue radiometry and multiscale optical modelling support our interpretation of the system's photophysics. This highly evolved 'three-dimensional' biophotonic system suggests a strategy for more efficient, damage-resistant photovoltaic materials and more spatially efficient solar production of algal biofuels, foods and chemicals.

  6. The Clam-Gallas Palace in Prague: Emblematic Architecture?

    Czech Academy of Sciences Publication Activity Database

    Konečný, Lubomír

    2010-01-01

    Roč. 18, - (2010), s. 1-10 ISSN 0885-968X Institutional research plan: CEZ:AV0Z80330511 Keywords : Clam-Gallas Palace * Johann Bernhard Fischer von Erlach * architecture * emblem s * imprints Subject RIV: AL - Art, Architecture, Cultural Heritage

  7. Urinary incontinence - tension-free vaginal tape

    Science.gov (United States)

    ... ency/article/007377.htm Urinary incontinence - tension-free vaginal tape To use the sharing features on this page, please enable JavaScript. Placement of tension-free vaginal tape is surgery to help control stress urinary ...

  8. Effects of ankle eversion taping using kinesiology tape in a patient with ankle inversion sprain

    OpenAIRE

    Lee, Sun-Min; Lee, Jung-Hoon

    2016-01-01

    [Purpose] The aim of this study was to report the effects of ankle eversion taping using kinesiology tape on ankle inversion sprain. [Subject] The subject was a 21-year-old woman with Grade 2 ankle inversion sprain. [Methods] Ankle eversion taping was applied to the sprained left ankle using kinesiology tape for 4 weeks (average, 15?h/day). [Results] Ankle instability and pain were reduced, and functional dynamic balance was improved after ankle eversion taping for 4 weeks. The Cumberland Ank...

  9. Analisis Perilaku Konsumen Proll Tape di Jember

    OpenAIRE

    Kusmiati, Ati; Widjayanti, Lenny; Risaldi, Feri

    2009-01-01

    Proll tape is a agroindustrial product which used agriculture product as a basic material. It is a diversification product from tape and mixed with some flavour. It can be found in the gift store. Proll tape marketing strategic will influence consumer behaviour in the decision buying. Consumer buy proll tape as a gift as beside on their own consumption. Consumer considers proll tape has a good quality so that it can fill consumer needed. Purpose of the research to find out the influence facto...

  10. Pinning Mechanisms in YBCO Tapes

    CERN Document Server

    Spera, Marcello; Ballarino, Amalia

    2015-01-01

    In this thesis work, a study on flux pinning mechanisms of commercial YBCO tapes is presented. This study has been performed via critical current characterization using transport (via direct I-V curves) and magnetization (via a Vibrating Sample Magnetometer) measurements. The latter ones turned out to be better concerning the comprehension of the pinning landscape of the provided samples, as a wider range of magnetic fields and temperatures is available for those measurements in the setup I used. The comparison of the experimental data with existing theoretical models allowed me to draw a picture of the pinning mechanisms underlying in each sample, and they turned out to be quite different one another. Moreover, for high-performance research tapes, another interesting feature has been found: the counterplay between the self-field critical current and the in-field one. Very well engineered artificial pinning structures limit the self-field critical current density due to the hi...

  11. Inactivation of Vibrio parahaemolyticus in hard clams (Mercanaria mercanaria) by high hydrostatic pressure (HHP) and the effect of HHP on the physical characteristics of hard clam meat.

    Science.gov (United States)

    Mootian, Gabriel K; Flimlin, George E; Karwe, Mukund V; Schaffner, Donald W

    2013-02-01

    Shellfish may internalize dangerous pathogens during filter feeding. Traditional methods of depuration have been found ineffective against certain pathogens. The objective was to explore high hydrostatic pressure (HHP) as an alternative to the traditional depuration process. The effect of HHP on the survival of Vibrio parahaemolyticus in live clams (Mercanaria mercanaria) and the impact of HHP on physical characteristics of clam meat were investigated. Clams were inoculated with up to 7 log CFU/g of a cocktail of V. parahaemolyticus strains via filter feeding. Clams were processed at pressures ranging from 250 to 552 MPa for hold times ranging between 2 and 6 min. Processing conditions of 450 MPa for 4 min and 350 MPa for 6 min reduced the initial concentration of V. parahaemolyticus to a nondetectable level (5 log reductions. The volume of clam meat (processed in shell) increased with negligible change in mass after exposure to pressure at 552 MPa for 3 min, while the drip loss was reduced. Clams processed at 552 MPa were softer compared to those processed at 276 MPa. However, all HHP processed clams were found to be harder compared to unprocessed. The lightness (L*) of the meat increased although the redness (a*) decreased with increasing pressure. Although high pressure-processed clams may pose a significantly lower risk from V. parahaemolyticus, the effect of the accompanied physical changes on the consumer's decision to purchase HHP clams remains to be determined. Shellfish may contain dangerous foodborne pathogens. Traditional methods of removing those pathogen have been found ineffective against certain pathogens. The objective of this research was to determine the effect of high hydrostatic pressure on V. parahaemolyticus in clams. Processing conditions of 450 MPa for 4 min and 350 MPa for 6 min reduced the initial concentration of V. parahaemolyticus to a nondetectable level, achieving >5 log reductions. © 2013 Institute of Food Technologists®

  12. Digital tape unit test facility software

    Science.gov (United States)

    Jackson, J. T.

    1971-01-01

    Two computer programs are described which are used for the collection and analysis of data from the digital tape unit test facility (DTUTF). The data are the recorded results of skew tests made on magnetic digital tapes which are used on computers as input/output media. The results of each tape test are keypunched onto an 80 column computer card. The format of the card is checked and the card image is stored on a master summary tape via the DTUTF card checking and tape updating system. The master summary tape containing the results of all the tape tests is then used for analysis as input to the DTUTF histogram generating system which produces a histogram of skew vs. date for selected data, followed by some statistical analysis of the data.

  13. The neutron beam users tape management system

    International Nuclear Information System (INIS)

    Lyall, B.; Johnson, M.W.

    1977-02-01

    Systems are described for dealing with data collected at the High Flux Reactor, Institut Laue-Langevin, Grenoble and brought on magnetic tape to the Neutron Beam Research Unit at the Rutherford Laboratory. The first system, named GNAT, was designed to archive the incoming 800 bpi tapes onto 6250 bpi tapes (to enable them to return to the ILL). The archiving program, besides choosing the archive tapes, keeping a record of the data sets archived, and writing the archive tape, should be able to cope with incoming tapes whose formats are somewhat different from the standard IBM format. The second system, named FONT, was designed to maintain a record of all the tapes in the NBRU's possession, their whereabouts and what data, if any, are on them. (U.K.)

  14. Biodiesel Production from Castor Oil by Using Calcium Oxide Derived from Mud Clam Shell

    OpenAIRE

    Ismail, S.; Ahmed, A. S.; Anr, Reddy; Hamdan, S.

    2016-01-01

    The catalytic potential of calcium oxide synthesized from mud clam shell as a heterogeneous catalyst for biodiesel production was studied. The mud clam shell calcium oxide was characterized using particle size analyzer, Fourier transform infrared spectroscopy, scanning electron microscopy, and BET gas sorption analyzer. The catalyst performance of mud clam shell calcium oxide was studied in the transesterification of castor oil as biodiesel. Catalyst characterization and transesterification s...

  15. Ancient clam gardens, traditional management portfolios, and the resilience of coupled human-ocean systems

    Directory of Open Access Journals (Sweden)

    Julia Jackley

    2016-12-01

    Full Text Available Indigenous communities have actively managed their environments for millennia using a diversity of resource use and conservation strategies. Clam gardens, ancient rock-walled intertidal beach terraces, represent one example of an early mariculture technology that may have been used to improve food security and confer resilience to coupled human-ocean systems. We surveyed a coastal landscape for evidence of past resource use and management to gain insight into ancient resource stewardship practices on the central coast of British Columbia, Canada. We found that clam gardens are embedded within a diverse portfolio of resource use and management strategies and were likely one component of a larger, complex resource management system. We compared clam diversity, density, recruitment, and biomass in three clam gardens and three unmodified nonwalled beaches. Evidence suggests that butter clams (Saxidomus gigantea had 1.96 times the biomass and 2.44 times the density in clam gardens relative to unmodified beaches. This was due to a reduction in beach slope and thus an increase in the optimal tidal range where clams grow and survive best. The most pronounced differences in butter clam density between nonwalled beaches and clam gardens were found at high tidal elevations at the top of the beach. Finally, clam recruits (0.5-2 mm in length tended to be greater in clam gardens compared to nonwalled beaches and may be attributed to the addition of shell hash by ancient people, which remains on the landscape today. As part of a broader social-ecological system, clam garden sites were among several modifications made by humans that collectively may have conferred resilience to past communities by providing reliable and diverse access to food resources.

  16. Further development of the SEA-Clam wave energy converter

    Energy Technology Data Exchange (ETDEWEB)

    Bellamy, N.W.; Peatfield, A.M.

    1984-04-01

    The final design of the SEA-Clam as a unit for a large 2 GW scheme has been described. This is the leading wave energy device arising out of the UK National Wave Energy Program and is seen as having the greatest potential for further development particularly for smaller scale applications. The small scale market for wave energy is examined and the design and cost parameters evaluated for the 250 kW to 1000 kW range of SEA-Clam units. Building a demonstration prototype rated at 650 kW and producing an annual average output of 250 kW is identified as the next step towards the commercial exploitation of wave energy.

  17. Sensory Characteristics of Mud Clam (Polymesoda Erosa) Hydrolysate

    International Nuclear Information System (INIS)

    Normah Ismail; Noorasma Mustakim

    2016-01-01

    Mud clam (Polymesoda erosa) was hydrolysed using two different microbial enzymes; alcalase and flavourzyme. The volatile compounds, amino acids and molecular weight associated with umami and bitter taste in mud clam hydrolysate were determined by head space solid phase micro-extraction gas chromatography (HS-SPME-GCMS), High performance liquid chromatography (HPLC) and sodium dodecyl sulphate polyacrylamide gel electrophoresis (SDS-PAGE). The characteristics of hydrolysates produced using alcalase and flavourzyme were compared. In total, eighteen, seven and six volatile compounds were identified in the flesh, alcalase hydrolysate and flavourzyme hydrolysate, respectively. 2-piperidinone volatile compound content which is associated with bitterness was 6.79 % in alcalase hydrolysate and 3.78 % in flavourzyme hydrolysate. SDS-PAGE results showed that alcalase hydrolysate contains smaller peptide (<52 kDa) compared to flavourzyme hydrolysate (<126 kDa). In addition, sensory analysis using quantitative descriptive analysis (QDA) showed that flavourzyme hydroysate was the least bitter but elicited more umami taste compared to alcalase hydrolysate. Further treatments are still needed to enhance umami taste and to remove bitter taste in mud clam hydrolysate. (author)

  18. Bitterness and Physichochemical Properties of Angelwing Clam (Pholas Orientalis) Hydrolysate

    International Nuclear Information System (INIS)

    Normah Ismail; Nurul Fasihah Razak

    2016-01-01

    Protein hydrolysates from angelwing clam were obtained by enzymatic hydrolysis using bromelain. The bitterness of hydrolysates was evaluated based on the degree hydrolysis (DH), sensory analysis, molecular weight distribution and functional group. By using 3 % of enzyme substrate ratio bromelain resulted in high DH value at 12.57 % when angelwing clam was hydrolysed for 2 hours. Sensory analysis showed that angelwing hydrolysate was bitter. Angelwing hydrolysate had molecular weight below 50 kDa. The lower molecular weight indicated that the protein has been degraded into smaller peptide chains which contribute to bitter taste. Moreover, the high peak of amine group in angelwing hydrolysate (3385.6 cm -1 ) suggested that bitterness exists. Angelwing hydrolysate had higher protein content, lower fat content and had good water holding capacity than the flesh. This result suggested that angelwing hydrolysate could be useful as food ingredient even though bitter taste developed after the hydrolysis. Thus, debittering should be considered in order to pave the way for full utilization of angelwing clam hydrolysate as a food ingredient. (author)

  19. Morula-like cells in photo-symbiotic clams harboring zooxanthellae.

    Science.gov (United States)

    Nakayama, K; Nishijima, M; Maruyama, T

    1998-06-01

    Symbiosis is observed between zooxanthellae, symbiotic dinoflagellates, and giant clams and related clams which belong to the families Tridacnidae and Cardiidae. We have previously shown that a photo-symbiotic clam Tridacna crocea has three types of hemocytes, the eosinophilic granular hemocyte with phagocytic activity, the agranular cell with electron lucent granules, and the morula-like cell with large (ca. 2 mum in diameter) colorless granules. The function of the morula-like cell is not clear, but it has not been reported in any other bivalves except photo-symbiotic clams T. crocea and Tridacna maxima. In order to clarify whether it is specific to photo-symbiotic clams or not, we studied hemocytes in the photo-symbiotic clams Tridacna derasa (Tridacnidae), Hippopus hippopus (Tridacnidae) and Corculum cardissa (Cardiidae), and a closely related non-symbiotic clam Fulvia mutica (Cardiidae). The eosinophilic granular hemocytes and the agranular cells were found in all of the clams examined. However, the morula-like cells which were packed with many large electron dense granules (ca. 2 mum in diameter), were observed only in the photo-symbiotic clams. In F. mutica, a closely related non-symbiotic clam, this type of hemocyte was not found. Instead a hemocyte with vacuoles and a few large granules containing peroxidase activity was observed. The large granules of F. mutica varied in size from ca. 1-9 mum in diameter. Present data suggests that the presence of morula-like cells is restricted to photo-symbiotic clams and that the hemocytes associated with the morula-like cells may have some functional relationship to symbiosis with zooxanthellae.

  20. A SOCIAL COST-BENEFIT ANALYSIS OF A SMALL-SCALE CLAM ...

    African Journals Online (AJOL)

    Results from the CBA yielded positive net present values (NPVs) for project options involving live clams being sold on the export market (to Hong Kong) for R24.70 kg-1 and negative NPVs for domestic market options (Johannesburg and Cape Town), where the clam would be sold for R6.50 kg-1. Assuming a discount rate ...

  1. The Stability of the Giant Clam Holobiont over Time and during Bleaching Stress

    KAUST Repository

    Pappas, Melissa

    2017-12-01

    The stability of marine photosymbiotic holobionts has major implications for the future of coral reef communities. This study aims to describe the stability of the Red Sea giant clam holobiont over the duration of one year and during induced bleaching stress under laboratory thermal manipulations. Tridacnid clams of the species Tridacna maxima were sampled at three reef locations near the central Saudi coast of the Red Sea. Associated Symbiodinium of Red Sea giant clams have previously been described to be part of only Clade A, which suggests a strong specificity in the clam-algal partnership, but specific types and potential shifting of types within this clade have not been examined for giant clams. The results from this study confirm that tridacnid symbiont types shift over time and the change between three A1 types suggests a biological and functional significance of two undescribed A1 Symbiodinium types. Experimental bleaching shows that Red Sea giant clams, although exposed to rather hot temperatures naturally, will bleach at 34°C after two weeks, and severely bleached clams likely will not recover. During bleaching, Symbiodinium types shift as well, and shift more drastically than seasonal shifts during the year. This shifting may be an evolved characteristic of the giant clam to aid in surviving major changes in the environment. However, more research is needed to determine if these holobionts are capable of keeping up with the global forecast of warming in reef environments.

  2. Assessment of clam ruditapes philippinarum as Heavy metal bioindicators using NMR-based metabolomics

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Xiaoli; Zhang, Linbao; You, Liping [Key Laboratory of Coastal Zone Environment Processes, CAS, Shandong Provincial Key Laboratory of Coastal Zone Environment Processes, Yantai Institute of Coastal Zone Research, Chinese Academy of Sciences, Yantai (China); The Graduate School of Chinese Academy of Sciences, Beijing (China); Yu, Junbao; Cong, Ming; Wang, Qing; Li, Fei; Li, Lianzhen; Zhao, Jianmin; Li, Chenghua; Wu, Huifeng [Key Laboratory of Coastal Zone Environment Processes, CAS, Shandong Provincial Key Laboratory of Coastal Zone Environment Processes, Yantai Institute of Coastal Zone Research, Chinese Academy of Sciences, Yantai (China)

    2011-08-15

    There are mainly distributed three pedigrees (White, Liangdao Red, and Zebra) of Manila clam Ruditapes philippinarum in Yantai population along the Bohai marine and coast. However, the biological differences to environmental stressors have been ignored in toxicology studies, which could lead to the distortion of biological interpretations of toxicological effects induced by environmental contaminants. In this study, we applied a system biology approach, metabolomics to compare the metabolic profiles in digestive gland from three pedigrees of clam and characterize and compare the metabolic responses induced by mercury in clam digestive gland tissues to determine a sensitive pedigree of clam as a preferable bioindicator for metal pollution monitoring and toxicology research. The most abundant metabolites, respectively, included branched-chain amino acids, alanine, and arginine in White samples, glutamate, dimethylglycine, and glycine in Zebra clams and acetylcholine, betaine, glucose, and glycogen in Liangdao Red clams. After 48 h exposure of 20 {mu}g L{sup -1} Hg{sup 2+}, the metabolic profiles from the three pedigrees of clams showed differentially significant changes in alanine, glutamate, succinate, taurine, hypotaurine, glycine, arginine, glucose, etc. Our findings indicate the toxicological effects of mercury exposure in Manila clams including the neurotoxicity, disturbances in energetic metabolisms and osmoregulation in the digestive glands and suggest that Liangdao Red pedigree of clam could be a preferable bioindicator for the metal pollution monitoring based on the more sensitive classes of metabolic changes from digestive glands compared with other two (White and Zebra) pedigrees of clams. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  3. Data analysis of event tape and connection

    International Nuclear Information System (INIS)

    Gong Huili

    1995-01-01

    The data analysis on the VAX-11/780 computer is briefly described, the data is from the recorded event tape of JUHU data acquisition system on the PDP-11/44 computer. The connection of the recorded event tapes of the XSYS data acquisition system on VAX computer is also introduced

  4. Device measures static friction of magnetic tape

    Science.gov (United States)

    Cole, P. T.

    1967-01-01

    Device measures the coefficient of static friction of magnetic tape over a range of temperatures and relative humidities. It uses a strain gage to measure the force of friction between a reference surface and the tape drawn at a constant velocity of approximately 0.0001 inch per second relative to the reference surface.

  5. Multiple Generations on Video Tape Recorders.

    Science.gov (United States)

    Wiens, Jacob H.

    Helical scan video tape recorders were tested for their dubbing characteristics in order to make selection data available to media personnel. The equipment, two recorders of each type tested, was submitted by the manufacturers. The test was designed to produce quality evaluations for three generations of a single tape, thereby encompassing all…

  6. Report on feasibility study of the Clam Wave Energy Device

    Energy Technology Data Exchange (ETDEWEB)

    1979-04-01

    The main emphasis of the feasibility study has been towards producing an acceptable spine design for the Clam wave energy converter. Concrete and steel designs based on a mathematical model of the waveloading have been produced. Progress is also reported in the design of a bellows for a low-pressure air power transmission system. A narrow wave tank and scale model have been constructed in order to carry out a test programme on various aspects of the device's construction and performance.

  7. Second generation wave energy device - the clam concept

    Energy Technology Data Exchange (ETDEWEB)

    Bellamy, N.W.

    1981-01-01

    A device concept is presented which has arisen from a system approach adopted by a research group with considerable experience in the discipline of wave energy. The Clam, which can be classified as a spine-based pneumatic terminator, is deemed to be a second generation wave energy device in that it tries to utilize system components already identified as attractive, while at the same time avoiding known problem areas. A working model of this wave power device at an engineering scale is discussed for trials in real waves. 3 refs.

  8. Photosymbiotic Giant Clams are Transformers of Solar Flux

    Science.gov (United States)

    2014-01-01

    function to forward-scatter light reflected from high albedo sand or from the highly reflec- tive clam shell itself (M. Lim 2014, personal communication...grains: aggregates made of crystalline water ice . Icarus 215, 682–694. (doi:10.1016/j.icarus.2011.04.011) 17. Denton EJ, Land MF. 1971 Mechanism of...2005.50.5.1490) 29. McFarland WN, Munz FW. 1975 Part II: the photic environment of clear tropical seas during the day. Vis. Res. 15, 1063–1070. (doi

  9. Tape SCSI monitoring and encryption at CERN

    Science.gov (United States)

    Laskaridis, Stefanos; Bahyl, V.; Cano, E.; Leduc, J.; Murray, S.; Cancio, G.; Kruse, D.

    2017-10-01

    CERN currently manages the largest data archive in the HEP domain; over 180PB of custodial data is archived across 7 enterprise tape libraries containing more than 25,000 tapes and using over 100 tape drives. Archival storage at this scale requires a leading edge monitoring infrastructure that acquires live and lifelong metrics from the hardware in order to assess and proactively identify potential drive and media level issues. In addition, protecting the privacy of sensitive archival data is becoming increasingly important and with it the need for a scalable, compute-efficient and cost-effective solution for data encryption. In this paper, we first describe the implementation of acquiring tape medium and drive related metrics reported by the SCSI interface and its integration with our monitoring system. We then address the incorporation of tape drive real-time encryption with dedicated drive hardware into the CASTOR [1] hierarchical mass storage system.

  10. Preparation and characterization of Bi-2223 tapes

    International Nuclear Information System (INIS)

    Hense, K.; Kirchmayr, H.; Kovac, P.; Lackner, R.; Mueller, M.; Pachla, W.; Pitel, J.; Polak, M.; Usak, P.

    2003-01-01

    In a concerted action between Austrian, Slovakian and Polish research institutes Bi-2223 tapes have been prepared and characterized by different physical methods. Metallographic studies by optical as well as electron microscopy, measurements of critical current (angle dependent) and losses have been performed. Properties of individual filaments extracted from multifilamentary tapes were also studied. Uniformity of local I C of these filaments were considerably lower than that of the whole tape. This indicates that improvement of filament homogeneity could improve the over all J C in tapes. The application of these tapes for optimized magnet coils will also be discussed. From these investigations a better understanding of the mechanisms, limiting the critical current could be achieved and more optimized preparation methods can be envisioned

  11. White House Tapes of the Nixon Administration, 1971 to 1973

    Data.gov (United States)

    National Archives and Records Administration — This dataset provides information about the Nixon Administration's White House Tapes. The White House Tapes contain sound recordings of President Richard Nixon's...

  12. Great Lakes clams find refuge from zebra mussels in restored, lake-connected marsh (Ohio)

    Science.gov (United States)

    Nichols, S. Jerrine; Wilcox, Douglas A.

    2004-01-01

    Since the early 1990s, more than 95 percent of the freshwater clams once found in Lake Erie have died due to the exotic zebara mussel (Dreissena polymorpha). Zebra mussels attach themselves to native clams in large numbers, impeding the ability of the clams to eat and burrow. However, in 1996, we discovered a population of native clams in Metzger Marsh in western Lake Erie (about 50 miles [80 km] east of Toledo) that were thriving despite the longtime presence of zebra mussel in surrounding waters. At that time, Metzger Marsh was undergoing extensive restoration, including construction of a dike to replace the eroded barrier beach and of a water-control structure to maintain hydrologic connections with the lake (Wilcox and Whillans 1999). The restoration plan called for a drawdown of water levels to promote plant growth from the seedbank -- a process that would also destroy most of the clam population. State and federal resource managers recommended removing as many clams as possible to a site that was isolated from zebra mussels, and then returning them to the marsh after it was restored. We removed about 7,000 native clams in 1996 and moved them back to Metzger Marsh in 1999.

  13. Recovery of intertidal hardshelled clams in Prince William Sound from Exxon Valdez oiling and shoreline treatments

    International Nuclear Information System (INIS)

    Houghton, J.P.; Lees, D.C.; Driskell, W.B.

    1994-01-01

    Native little neck (Protothaca staminea) and butter clams (Saxidomus giganteus) were quantitatively surveyed from 1989 through 1993 to evaluate effects from the Exxon Valdez oil spill. Hydraulic washing of sand and gravel beaches altered beach morphology by transporting material down slope from upper elevations, often burying the lower beach in several centimeters of sediment having a relatively low content of fines and organic carbon. Hydraulically washed beaches showed significant reductions in clam densities in 1989 and 1990. Recruitment of clams was very limited on these beaches through 1993; as a result, clam densities on these hydraulically washed beaches remain very depressed compared to those on beaches that were unoiled or oiled but not washed. Littlenecks transplanted from a reference site to a heavily oiled but untreated site showed significant patterns of increased mortality, decreased growth, and increased bioaccumulation of PAH in response to a gradient in sediment PAH, This same heavily oiled site has consistently had among the highest rates of hardshelled clam recruitment of any of the sites sampled. Littlenecks also were transplanted to another heavily oiled beach that had been hydraulically washed and had little remaining hydrocarbons. These clams showed very high survival, yet this beach has had very little clam recruitment. It is hypothesized that recruitment at this site may be inhibited by the low level of finer sediments and low organic content remaining after washing

  14. Concentrations of organotin compounds in sediment and clams collected from coastal areas in Vietnam

    International Nuclear Information System (INIS)

    Midorikawa, Sayaka; Arai, Takaomi; Harino, Hiroya; Ohji, Madoka; Nguyen Duc Cu; Miyazaki, Nobuyuki

    2004-01-01

    Levels of butyltin (BT) and phenyltin (PT) compounds were determined in sediments and clam Meretrix spp. collected from north and central coastal areas in Vietnam. Concentrations of TBT in sediments ranged from 0.89 to 34 ng g -1 dry wt and those in clams ranged from 1.4 to 56 ng g -1 wet wt. The levels of TBT in sediments and clams from Vietnam were within limits reported from other countries. Further, the TBT level in clams was lower than the tolerable average residue level (TARL) estimated based on tolerable daily intake (TDI). Trace amounts of PTs were also found in both sediment and clam samples. In sediments from north and central Vietnam, the concentrations of TBT were highest in the order of Hue (28 ng g -1 dry wt), Cua Luc (15 ng g -1 dry wt), Sam Son (6.3 ng g -1 dry wt), and Tra Co (5.5 ng g -1 dry wt). Among the clams from north and central Vietnam, the levels of TBT in clams from Cua Luc were dramatically high at 47 ng g -1 wet wt. TBT formed the principal butyltin species in sediment at all sites studied. The ratios of TBT in sediment were higher among BT compounds at all study sites. Of total BTs, TBT was the dominant species in clams from almost all sites studied. In spatial distribution, TPT showed a pattern similar to TBT, suggesting the use of TPT as an antifouling paint. The partition coefficient between sediment and calms was calculated. The partition coefficients of TBT and TPT were 2.01 (0.56-5.5) and 9.23 (3.1-20), respectively. These results show that sediment-bound TBT is a source of contamination to clams in addition to dissolved TBT

  15. Identification of clam plasma proteins that bind its pathogen Quahog Parasite Unknown.

    Science.gov (United States)

    Hartman, Rachel; Pales Espinosa, Emmanuelle; Allam, Bassem

    2018-06-01

    The hard clam (Mercenaria mercenaria) is among the most economically-important marine species along the east coast of the United States, representing the first marine resource in several Northeastern states. The species is rather resilient to infections and the only important disease of hard clams results from an infection caused by Quahog Parasite Unknown (QPX), a protistan parasite that can lead to significant mortality events in wild and aquacultured clam stocks. Though the presence of QPX disease has been documented since the 1960s, little information is available on cellular and molecular interactions between the parasite and the host. This study examined the interactions between the clam immune system and QPX cells. First, the effect of clam plasma on the binding of hemocytes to parasite cells was evaluated. Second, clam plasma proteins that bind QPX cells were identified through proteomic (LC-MS/MS) analyses. Finally, the effect of prior clam exposure to QPX on the abundance of QPX-reactive proteins in the plasma was evaluated. Results showed that plasma factors enhance the attachment of hemocytes to QPX. Among the proteins that specifically bind to QPX cells, several lectins were identified, as well as complement component proteins and proteolytic enzymes. Furthermore, results showed that some of these lectins and complement-related proteins are inducible as their abundance significantly increased following QPX challenge. These results shed light on plasma proteins involved in the recognition and binding of parasite cells and provide molecular targets for future investigations of factors involved in clam resistance to the disease, and ultimately for the selection of resistant clam stocks. Copyright © 2018 Elsevier Ltd. All rights reserved.

  16. Melt formed superconducting joint between superconducting tapes

    International Nuclear Information System (INIS)

    Benz, M.G.; Knudsen, B.A.; Rumaner, L.E.; Zaabala, R.J.

    1992-01-01

    This patent describes a superconducting joint between contiguous superconducting tapes having an inner laminate comprised of a parent-metal layer selected from the group niobium, tantalum, technetium, and vanadium, a superconductive intermetallic compound layer on the parent-metal layer, a reactive-metal layer that is capable of combining with the parent-metal and forming the superconductive intermetallic compound, the joint comprising: a continuous precipitate of the superconductive intermetallic compound fused to the tapes forming a continuous superconducting path between the tapes

  17. Kinesio Taping Fundamentals for the Equine Athlete.

    Science.gov (United States)

    Molle, Sybille

    2016-04-01

    The Kinesio taping method was developed in Japan for use in humans in 1979. The use of complementary therapies is becoming common in equine athletes and the discovery of Kinesio taping potential brought it into the animal world. Kinesio taping can be used to treat a wide range of clinical conditions, from tendon injuries to neurologic disorders and from muscle contractures to postural insufficiencies. Its use in veterinary medicine is promising, but relies heavily on evidence-based clinical reports. Further scientific research is needed to fully understand the real effectiveness of application. Copyright © 2016 Elsevier Inc. All rights reserved.

  18. Recolonization of reactor cooling water system by the Asiatic clam Corbicula fluminea

    International Nuclear Information System (INIS)

    Harvey, R.S.

    1978-01-01

    Recolonization rates for the Asiatic clam Corbicula fluminea ranged from 3.0 to 5.6 metric tons per year in cooling water basins for a nuclear production reactor at the Savannah River Plant. However, a 10-month cleaning cycle for each basin (flow area, 6100 m 2 ) keeps the depth of the silt/clam layer low. With this cleaning frequency, Corbicula are not reaching heat exchangers at sufficient size or in sufficient numbers to restrict flow. Data are presented on the size/age distribution for clams recolonizing cooling water basins between cleanings

  19. The Stability of the Giant Clam Holobiont over Time and during Bleaching Stress

    KAUST Repository

    Pappas, Melissa

    2017-01-01

    Experimental bleaching shows that Red Sea giant clams, although exposed to rather hot temperatures naturally, will bleach at 34°C after two weeks, and severely bleached clams likely will not recover. During bleaching, Symbiodinium types shift as well, and shift more drastically than seasonal shifts during the year. This shifting may be an evolved characteristic of the giant clam to aid in surviving major changes in the environment. However, more research is needed to determine if these holobionts are capable of keeping up with the global forecast of warming in reef environments.

  20. Tape Cassette Bacteria Detection System

    Science.gov (United States)

    1973-01-01

    The design, fabrication, and testing of an automatic bacteria detection system with a zero-g capability and based on the filter-capsule approach is described. This system is intended for monitoring the sterility of regenerated water in a spacecraft. The principle of detection is based on measuring the increase in chemiluminescence produced by the action of bacterial porphyrins (i.e., catalase, cytochromes, etc.) on a luminol-hydrogen peroxide mixture. Since viable as well as nonviable organisms initiate this luminescence, viable organisms are detected by comparing the signal of an incubated water sample with an unincubated control. Higher signals for the former indicate the presence of viable organisms. System features include disposable sealed sterile capsules, each containing a filter membrane, for processing discrete water samples and a tape transport for moving these capsules through a processing sequence which involves sample concentration, nutrient addition, incubation, a 4 Molar Urea wash and reaction with luminol-hydrogen peroxide in front of a photomultiplier tube. Liquids are introduced by means of a syringe needle which pierces a rubber septum contained in the wall of the capsule. Detection thresholds obtained with this unit towards E. coli and S. marcescens assuming a 400 ml water sample are indicated.

  1. A COMPARITIVE STUDY ON EFFECTIVENESS OF TAPING WITH IONTOPHORESIS AND TAPING ALONE IN CHRONIC PLANTAR FASCITIS

    OpenAIRE

    Biju Chetri, U.T. Ifthikar Ali, Madhusmita Koch, Abhijit Dutta

    2016-01-01

    Background: Plantar fasciitis is a painful condition caused by microtrauma to plantar fascia due to overuse. It is a most common cause of heel pain in runners. Various studies proved taping and Iontophoresis as effective in the treating plantar fasciitis. But there are no studies comparing the combined effect of iontophoresis with taping and taping alone in the treatment of plantar fasciitis. Methods: 50 patients suffering from plantar fasciitis who met the inclusion criteria were selected...

  2. Risk-based probabilistic approach to assess the impact of false mussel invasions on farmed hard clams.

    Science.gov (United States)

    Liao, Chung-Min; Ju, Yun-Ru; Chio, Chia-Pin; Chen, Wei-Yu

    2010-02-01

    The purpose of this article is to provide a risk-based predictive model to assess the impact of false mussel Mytilopsis sallei invasions on hard clam Meretrix lusoria farms in the southwestern region of Taiwan. The actual spread of invasive false mussel was predicted by using analytical models based on advection-diffusion and gravity models. The proportion of hard clam colonized and infestation by false mussel were used to characterize risk estimates. A mortality model was parameterized to assess hard clam mortality risk characterized by false mussel density and infestation intensity. The published data were reanalyzed to parameterize a predictive threshold model described by a cumulative Weibull distribution function that can be used to estimate the exceeding thresholds of proportion of hard clam colonized and infestation. Results indicated that the infestation thresholds were 2-17 ind clam(-1) for adult hard clams, whereas 4 ind clam(-1) for nursery hard clams. The average colonization thresholds were estimated to be 81-89% for cultivated and nursery hard clam farms, respectively. Our results indicated that false mussel density and infestation, which caused 50% hard clam mortality, were estimated to be 2,812 ind m(-2) and 31 ind clam(-1), respectively. This study further indicated that hard clam farms that are close to the coastal area have at least 50% probability for 43% mortality caused by infestation. This study highlighted that a probabilistic risk-based framework characterized by probability distributions and risk curves is an effective representation of scientific assessments for farmed hard clam in response to the nonnative false mussel invasion.

  3. Ankle inversion taping using kinesiology tape for treating medial ankle sprain in an amateur soccer player

    OpenAIRE

    Lee, Sun-Min; Lee, Jung-Hoon

    2015-01-01

    [Purpose] The purpose of this study was to report the effects of ankle inversion taping using kinesiology tape in a patient with a medial ankle sprain. [Subject] A 28-year-old amateur soccer player suffered a Grade 2 medial ankle sprain during a match. [Methods] Ankle inversion taping was applied to the sprained ankle every day for 2 months. [Results] His symptoms were reduced after ankle inversion taping application for 2 months. The self-reported function score, the reach distances in the S...

  4. A COMPARITIVE STUDY ON EFFECTIVENESS OF TAPING WITH IONTOPHORESIS AND TAPING ALONE IN CHRONIC PLANTAR FASCITIS

    Directory of Open Access Journals (Sweden)

    Biju Chetri

    2016-04-01

    Full Text Available Background: Plantar fasciitis is a painful condition caused by microtrauma to plantar fascia due to overuse. It is a most common cause of heel pain in runners. Various studies proved taping and Iontophoresis as effective in the treating plantar fasciitis. But there are no studies comparing the combined effect of iontophoresis with taping and taping alone in the treatment of plantar fasciitis. Methods: 50 patients suffering from plantar fasciitis who met the inclusion criteria were selected. The subjects were randomly divided into two groups i.e. Group A and Group B. Group A received taping, iontophoresis with plantar fascia stretching. Group B received taping and plantar fascia stretching. A total of 6 treatment sessions were given on alternate days over a period of two weeks for both the groups. Results: VAS and FFI scores across baseline and post intervention showed a significant improvement statistically in their mean scores between Groups A and B (P<0.05. Between group comparison of VAS and FFI scores, it showed that subject treated with Iontophoresis in combination with taping and plantar fascia stretch (Group A had significant improvement in VAS and functional ability when compared to subjects treated with taping and plantar fascia stretching alone (Group B. Conclusion: Iontophoresis along with Taping and plantar fascia stretching gave an additional benefit when compared with Taping and plantar fascia stretching alone in reducing pain and improving function in plantar fasciitis.

  5. Multi-filamentary REBCO tapes fabricated by scratching a buffer layer along the tape longitudinal direction

    Energy Technology Data Exchange (ETDEWEB)

    Kurihara, Chihaya, E-mail: chihaya.kurihara@jp.fujikura.com [Fujikura Ltd., 1440, Mutsuzaki, Sakura, Chiba 285-8550 (Japan); Fujita, Shinji; Nakamura, Naonori; Igarashi, Mitsunori; Iijima, Yasuhiro [Fujikura Ltd., 1440, Mutsuzaki, Sakura, Chiba 285-8550 (Japan); Higashikawa, Kohei; Uetsuhara, Dai; Kiss, Takanobu; Iwakuma, Masataka [Kyushu University, 744 Motooka, Nishi-Ku, Fukuoka 819-0395 (Japan)

    2016-11-15

    Highlights: • We developed new method of slitting tape between buffer layer processes for multi-filamentary tape. • By scratching buffer layer along the tape longitudinal direction, we find that REBCO layer is divided easily without damaging it. • We have developed 100 m class multi-filamentary REBCO tapes which are suitable for superconducting coils. - Abstract: A method for making multi-filamentary REBCO tapes by only scratching buffer layer was developed for coil application which requires accurate magnetic fields. By continuous I{sub c} measurement, we found that our new multi-filamentary tape could provide almost equal I{sub c} compared to conventional tapes. Then, using EBSD and RTR-SHPM methods, a divided structure of REBCO layer was surely confirmed. AC loss was also decreased. Furthermore, the result of delamination test of our new multi-filamentary tape showed enough mechanical property. As a result, we have succeeded in developing 100 m class multi-filamentary tape for superconducting coil.

  6. Multi-filamentary REBCO tapes fabricated by scratching a buffer layer along the tape longitudinal direction

    International Nuclear Information System (INIS)

    Kurihara, Chihaya; Fujita, Shinji; Nakamura, Naonori; Igarashi, Mitsunori; Iijima, Yasuhiro; Higashikawa, Kohei; Uetsuhara, Dai; Kiss, Takanobu; Iwakuma, Masataka

    2016-01-01

    Highlights: • We developed new method of slitting tape between buffer layer processes for multi-filamentary tape. • By scratching buffer layer along the tape longitudinal direction, we find that REBCO layer is divided easily without damaging it. • We have developed 100 m class multi-filamentary REBCO tapes which are suitable for superconducting coils. - Abstract: A method for making multi-filamentary REBCO tapes by only scratching buffer layer was developed for coil application which requires accurate magnetic fields. By continuous I_c measurement, we found that our new multi-filamentary tape could provide almost equal I_c compared to conventional tapes. Then, using EBSD and RTR-SHPM methods, a divided structure of REBCO layer was surely confirmed. AC loss was also decreased. Furthermore, the result of delamination test of our new multi-filamentary tape showed enough mechanical property. As a result, we have succeeded in developing 100 m class multi-filamentary tape for superconducting coil.

  7. Levitation characteristics of HTS tape stacks

    Energy Technology Data Exchange (ETDEWEB)

    Pokrovskiy, S. V.; Ermolaev, Y. S.; Rudnev, I. A. [National Research Nuclear University MEPhI (Moscow Engineering Physics Institute), Moscow (Russian Federation)

    2015-03-15

    Due to the considerable development of the technology of second generation high-temperature superconductors and a significant improvement in their mechanical and transport properties in the last few years it is possible to use HTS tapes in the magnetic levitation systems. The advantages of tapes on a metal substrate as compared with bulk YBCO material primarily in the strength, and the possibility of optimizing the convenience of manufacturing elements of levitation systems. In the present report presents the results of the magnetic levitation force measurements between the stack of HTS tapes containing of tapes and NdFeB permanent magnet in the FC and ZFC regimes. It was found a non- linear dependence of the levitation force from the height of the array of stack in both modes: linear growth at small thickness gives way to flattening and constant at large number of tapes in the stack. Established that the levitation force of stacks comparable to that of bulk samples. The numerical calculations using finite element method showed that without the screening of the applied field the levitation force of the bulk superconductor and the layered superconductor stack with a critical current of tapes increased by the filling factor is exactly the same, and taking into account the screening force slightly different.

  8. Elimination of Escherichia coli and Salmonella in Clam by Using Zeolite in a Station of Depuration.

    Science.gov (United States)

    Gdoura, Morsi; Sellami, Hanen; Khannous, Lamia; Ketata, Najib; Neila, Idriss Ben; Traore, Al Ibrahim; Chekir, Zouhair; Gdoura, Radhouane

    2017-09-01

      The application of natural zeolite for water and wastewater treatment has been carried out and is still a promising technique in environmental cleaning processes. Natural zeolite can be used to improve the purification process of clams (Ruditapes decussatus). Thus, our study aimed at improving the clam purification system in order to reduce Escherichia coli and eliminate Salmonella in samples artificially contaminated with this bacterium using a natural zeolite to replace the biological filter. The results showed that zeolite used in a depuration system improved the clam purification process. Moreover, natural zeolite exhibited high performance in the adsorption of bacteria and allowed to reduce the Escherichia coli abundance in 24 h, thus ensuring purified clams conformity with the ISO 16649-3 standard. These results indicate the beneficial effects of using zeolite in the adsorption of bacteria and the reduction in the abundance of Escherichia coli and set the Salmonella from marine organisms.

  9. Biodiesel Production from Castor Oil by Using Calcium Oxide Derived from Mud Clam Shell

    Directory of Open Access Journals (Sweden)

    S. Ismail

    2016-01-01

    Full Text Available The catalytic potential of calcium oxide synthesized from mud clam shell as a heterogeneous catalyst for biodiesel production was studied. The mud clam shell calcium oxide was characterized using particle size analyzer, Fourier transform infrared spectroscopy, scanning electron microscopy, and BET gas sorption analyzer. The catalyst performance of mud clam shell calcium oxide was studied in the transesterification of castor oil as biodiesel. Catalyst characterization and transesterification study results of synthesized catalyst proved the efficiency of the natural derived catalyst for biodiesel production. A highest biodiesel yield of 96.7% was obtained at optimal parameters such as 1 : 14 oil-to-methanol molar ratio, 3% w/w catalyst concentration, 60°C reaction temperature, and 2-hour reaction time. Catalyst reusability test shows that the synthesized calcium oxide from mud clam shell is reusable up to 5 times.

  10. Addressing Sustainability of Clam Farming in the Venice Lagoon

    Directory of Open Access Journals (Sweden)

    Donata Melaku Canu

    2011-09-01

    According to the System Approach Framework (SAF, based on previous studies and stakeholder interactions, we developed a model integrating ecological, social, and economic (ESE aspects. We chose the aspects necessary to represent the essential dynamics of major ecological, social, and economic clam farming system components to project the consequences of implementing alternative management policies and to address the ecological and social carrying capacity. Results of the simulations suggest that a properly managed farming system can sustain an acceptable income and support the local community, while reducing negative environmental impacts, social conflicts, and consumer health risks and improving system resilience. The results highlight the importance of an interdisciplinary, participatory, and adaptive approach in planning the management of this important renewable resource.

  11. Microstructure and mechanical properties in TIG welding of CLAM steel

    International Nuclear Information System (INIS)

    Zhu Qiang; Lei Yucheng; Chen Xizhang; Ren Wenjie; Ju Xin; Ye Yimin

    2011-01-01

    Tungsten insert gas (TIG) welding on China low activation martensitic (CLAM) steel under identical conditions was performed. Microhardness test, tensile test, Charpy impact test and microstructure measurements were carried out on TIG welded joints after post weld heat-treatment. Hardening at WM and softening in HAZ is detected in the TIG weld joint. Microhardness in WM decreased when the temperature of PWHT increased. The ultimate tensile stress of weld metal is higher than that of HAZ and BM. Absorbed energy increased with PWHT temperature rising, until PWHT was done at 760 deg. C/30 min, the specimen ductile fractured in local area. The microstructure of the weld metal for every specimen was found to be tempered martensite with a little of delta ferrite. M 23 C 6 particles are the predominant type of carbides. Oxide precipitate phases appeared in WM, which are the primary crack initiation sites and it is critically important minimize their formation.

  12. Welding techniques development of CLAM steel for Test Blanket Module

    Energy Technology Data Exchange (ETDEWEB)

    Li Chunjing [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); School of Nuclear Science and Technology, University of Science and Technology of China, Hefei, Anhui, 230027 (China)], E-mail: lcj@ipp.ac.cn; Huang Qunying; Wu Qingsheng; Liu Shaojun [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); School of Nuclear Science and Technology, University of Science and Technology of China, Hefei, Anhui, 230027 (China); Lei Yucheng [Jiangsu University, Zhenjiang, Jiangsu, 212013 (China); Muroga, Takeo; Nagasaka, Takuya [National Institute for Fusion Science, Toki, Jifu, 509-5292 (Japan); Zhang Jianxun [Xi' an Jiaotong University, Xi' an, Shanxi, 710049 (China); Li Jinglong [Northwestern Polytechnical University, Xi' an, Shanxi, 710072 (China)

    2009-06-15

    Fabrication techniques for Test Blanket Module (TBM) with CLAM are being under development. Effect of surface preparation on the HIP diffusion bonding joints was studied and good joints with Charpy impact absorbed energy close to that of base metal have been obtained. The mechanical properties test showed that effect of HIP process on the mechanical properties of base metal was little. Uniaxial diffusion bonding experiments were carried out to study the effect of temperature on microstructure and mechanical properties. And preliminary experiments on Electron Beam Welding (EBW), Tungsten Inert Gas (TIG) Welding and Laser Beam Welding (LBW) were performed to find proper welding techniques to assemble the TBM. In addition, the thermal processes assessed with a Gleeble thermal-mechanical machine were carried out as well to assist the fusion welding research.

  13. Sublethal Effects of Tributyltin on the Hard Shell Clam, Mercenaria mercenaria,

    Science.gov (United States)

    1988-01-01

    7) Laughlin, R.8., Jr., R.G. Gustafson and Peter Distribution/ Pendoley. 1987. Acute toxicity of tributyltin Avaiabilty Cdes( TBT ) to early life...Dist rSpecial Gustafson. 1987. Chronic embryo larval toxicity I of tributyltin ( TBT ) to the hard shell clam, All Aercenaria mercenaria. In preparation... tributyltin compounds ( TBT ). Post-set clams microalgae, Isochyis galmna Tahiti strain. TBT survived exposures up to 7.5 1i / for 25 days. No corentrations in

  14. Gametogenic development and spawning of the mud clam, Polymesoda erosa (Solander, 1876) at Chorao Island, Goa

    Digital Repository Service at National Institute of Oceanography (India)

    Clemente, S.; Ingole, B.S.

    islands of tropical and sub-tropical regions (Meehan 1982). Given the extensive use of the mangrove clam in the diet of many tropical islanders, the potential exists to exploit this clam commercially. An under- standing of the reproductive biology...: baban@nio.org Published in collaboration with the University of Bergen and the Institute of Marine Research, Norway, and the Marine Biological Laboratory, University of Copenhagen, Denmark Marine Biology Research, 2009; 5: 109C1121 (Accepted 12 June 2008...

  15. Methods and systems for fabricating high quality superconducting tapes

    Science.gov (United States)

    Majkic, Goran; Selvamanickam, Venkat

    2018-02-13

    An MOCVD system fabricates high quality superconductor tapes with variable thicknesses. The MOCVD system can include a gas flow chamber between two parallel channels in a housing. A substrate tape is heated and then passed through the MOCVD housing such that the gas flow is perpendicular to the tape's surface. Precursors are injected into the gas flow for deposition on the substrate tape. In this way, superconductor tapes can be fabricated with variable thicknesses, uniform precursor deposition, and high critical current densities.

  16. Soft shell clams Mya arenaria with disseminated neoplasia demonstrate reverse transcriptase activity

    Science.gov (United States)

    House, M.L.; Kim, C.H.; Reno, P.W.

    1998-01-01

    Disseminated neoplasia (DN), a proliferative cell disorder of the circulatory system of bivalves, was first reported in oysters in 1969. Since that time, the disease has been determined to be transmissible through water-borne exposure, but the etiological agent has not been unequivocally identified. In order to determine if a viral agent, possibly a retrovirus, could be the causative agent of DN, transmission experiments were performed, using both a cell-free filtrate and a sucrose gradient-purified preparation of a cell-free filtrate of DN positive materials. Additionally, a PCR-enhanced reverse transcriptase assay was used to determine if reverse transcriptase was present in tissues or hemolymph from DN positive soft shell clams Mya arenaria. DN was transmitted to healthy clams by injection with whole DN cells, but not with cell-free flitrates prepared from either tissues from DN positive clams, or DN cells. The cell-free preparations from DN-positive tissues and hemolymph having high levels of DN cells in circulation exhibited positive reactions in the PCR-enhanced reverse transcriptase assay. Cell-free preparations of hemolymph from clams having low levels of DN (<0.1% of cells abnormal), hemocytes from normal soft shell clams, and normal soft shell clam tissues did not produce a positive reaction in the PCR enhanced reverse transcriptase assay.

  17. REVIEW: Symbiosis between the Giant Clams (Bivalvia: Cardiidae and Zooxanthellae (Dinophyceae

    Directory of Open Access Journals (Sweden)

    UDHI EKO HERNAWAN

    2008-01-01

    Full Text Available Giant clams are the largest bivalves in the world that maintain a mutual relationship with zooxanthellae. Individual giant clam can harbor heterogeneous zooxanthellae, at least four taxa in genus Symbiodinium. The Symbiodinium lives in the zooxanthellal tubular system, a tube structure arising from one of the diverticular duct of the clam’s stomach. Since the numbers of zooxanthellae is the one of some significant factors contributing to the clams growth and survival, the giant clams need to adjust the number of zooxanthellae for physiological reason with unclear mechanism. The important role of the symbiotic relationship to the clams can be seen on the survival, growth and nutrition of the clams. There are at least two significant factors determining the symbiosis, i.e. water temperature in related with level of light intensities and ammonium-phosphate rate. Some topic is still unclear, i.e. the determination of species in genus Symbiodinium, the mechanism for adjusting the population numbers of the algae and what kind of environmental factors determining the symbiosis. Thereby further research is still needed to clarify those missing.

  18. Dimethylsulfoniopropionate in six species of giant clams and the evolution of dimethylsulfide after death

    Energy Technology Data Exchange (ETDEWEB)

    Hill, R.W.; Hill, S.D. [Michigan State Univ., East Lansing, MI (United States). Dept. of Zoology; Dacey, J.W.H. [Woods Hole Oceanographic Inst., Woods Hole, MA (United States). Dept. of Biology; Edward, A. [Micronesia College, Pohnpei (Micronesia, Federated States); Hicks, W.A. [Michigan State Univ., East Lansing, MI (United States). Dept. of Bioichemistry and Molecular Biology

    2004-05-01

    Dimethylsulfoniopropionate (DMSP) could accumulate in large concentrations in animals living symbiotically with algae. The giant clam family Tridacnidae accumulates DMSP because they have a symbiotic relationship with dinoflagellates (or zooxanthellae). In this study, well preserved clam tissues from the western Pacific Islands were analyzed to provide definitive evidence of DMSP in the tissues. Six of the common species in the Tridacnidae family were examined. The objective was to test the hypothesis that dimethyl sulfide (DMS) is released from clam tissues soon after death due to the breakdown of DMSP tissue. In particular, it determined if DMS is responsible for the problem of potent odours and off-taste that have hindered the commercial success of giant clams mariculture. Gas chromatography and mass spectrometry was used in this study to measure DMSP concentrations in siphonal mantle, byssal mantle, adductor muscle and gill tissues. The formation of DMS by tissues after death was documented. It was suggested that since giant clams associate with dinoflagellates, they could accumulate DMSP to high concentrations which could affect multiple properties and functions. It was concluded that the perishability of giant clam tissues is most likely due to the high concentrations of DMS produced one day post mortem. 15 refs., 2 tabs., 4 figs.

  19. Strategy for robot motion and path planning in robot taping

    Science.gov (United States)

    Yuan, Qilong; Chen, I.-Ming; Lembono, Teguh Santoso; Landén, Simon Nelson; Malmgren, Victor

    2016-06-01

    Covering objects with masking tapes is a common process for surface protection in processes like spray painting, plasma spraying, shot peening, etc. Manual taping is tedious and takes a lot of effort of the workers. The taping process is a special process which requires correct surface covering strategy and proper attachment of the masking tape for an efficient surface protection. We have introduced an automatic robot taping system consisting of a robot manipulator, a rotating platform, a 3D scanner and specially designed taping end-effectors. This paper mainly talks about the surface covering strategies for different classes of geometries. The methods and corresponding taping tools are introduced for taping of following classes of surfaces: Cylindrical/extended surfaces, freeform surfaces with no grooves, surfaces with grooves, and rotational symmetrical surfaces. A collision avoidance algorithm is introduced for the robot taping manipulation. With further improvements on segmenting surfaces of taping parts and tape cutting mechanisms, such taping solution with the taping tool and the taping methodology can be combined as a very useful and practical taping package to assist humans in this tedious and time costly work.

  20. Ubiquitous Graphene Electronics on Scotch Tape

    Science.gov (United States)

    Chung, Yoonyoung; Ho Kim, Hyun; Lee, Sangryun; Lee, Eunho; Won Kim, Seong; Ryu, Seunghwa; Cho, Kilwon

    2015-07-01

    We report a novel concept of graphene transistors on Scotch tape for use in ubiquitous electronic systems. Unlike common plastic substrates such as polyimide and polyethylene terephthalate, the Scotch tape substrate is easily attached onto various objects such as banknotes, curved surfaces, and human skin, which implies potential applications wherein electronics can be placed in any desired position. Furthermore, the soft Scotch tape serves as an attractive substrate for flexible/foldable electronics that can be significantly bent, or even crumpled. We found that the adhesive layer of the tape with a relatively low shear modulus relaxes the strain when subjected to bending. The capacitance of the gate dielectric made of oxidized aluminum oxide was 1.5 μF cm-2, so that a supply voltage of only 2.5 V was sufficient to operate the devices. As-fabricated graphene transistors on Scotch tape exhibited high electron mobility of 1326 (±155) cm2 V-1 s-1 the transistors still showed high mobility of 1254 (±478) cm2 V-1 s-1 even after they were crumpled.

  1. How PE tape performs under concrete coating

    International Nuclear Information System (INIS)

    Dritt, H.J.

    1984-01-01

    The program objectives were to evaluate the performance of polyethylene tape plant coating and fusion bonded epoxy powder systems with particular respect to the following: 1. Concrete coating application procedures; 2. The shear resistance during laying and retrieving operations of the coating at the various interfaces (a) Pipe and anti-corrosion coating; (b) Anti-corrosion coating and outerwrap; (c) Overlap areas of the anti-corrosion and outerwrap layers; (d) Between concrete and the various corrosion coatings during laying and retrieving operations. 3. Resistance to damage of the coating as a consequence of cracking or slippage of the concrete weight coating. 4. Ability of various coatings to withstand the damage during concrete application by both impact and compression methods; 5. Evaluation of tape and shrink sleeve joint coatings at the cut-back area as well as performance of tape under hot asphalt coating

  2. CLEARANCE OF ARCHIVE TAPE VAULT (BUILDING 186)

    CERN Multimedia

    EP Division

    1999-01-01

    The archive tape vault is being cleared to make way for the LHC experiments silicon facility.Experiments were contacted in February to arrange for the extended storage or destruction of archived volumes. Any who have not yet done so are asked to contactR. Minchin/IT immediately.This is also an opportunity to clear unused tapes or cartridges from around the site and have them destroyed ecologically. Please contact ep.smi.helpdesk@cern.ch to arrange for collection.A.E. Ball/EP-SMI

  3. Modelling of Tape Casting for Ceramic Applications

    DEFF Research Database (Denmark)

    Jabbari, Masoud

    was increased by improving the steady state model with a quasi-steady state analytical model. In order to control the most important process parameter, tape thickness, the two-doctor blade configuration was also modeled analytically. The model was developed to control the tape thickness based on the machine...... for magnetic refrigeration applications. Numerical models were developed to track the migration of the particles inside the ceramic slurry. The results showed the presence of some areas inside the ceramic in which the concentration of the particles is higher compared to other parts, creating the resulting...

  4. Placement suitability criteria of composite tape for mould surface in automated tape placement

    Directory of Open Access Journals (Sweden)

    Zhang Peng

    2015-10-01

    Full Text Available Automated tape placement is an important automated process used for fabrication of large composite structures in aeronautical industry. The carbon fiber composite parts realized with this process tend to replace the aluminum parts produced by high-speed machining. It is difficult to determine the appropriate width of the composite tape in automated tape placement. Wrinkling will appear in the tape if it does not suit for the mould surface. Thus, this paper deals with establishing placement suitability criteria of the composite tape for the mould surface. With the assumptions for ideal mapping and by applying some principles and theorems of differential geometry, the centerline trajectory of the composite tape is identified to follow the geodesic. The placement suitability of the composite tape is examined on three different types of non-developable mould surfaces and four criteria are derived. The developed criteria have been used to test the deposition process over several mould surfaces and the appropriate width for each mould surface is obtained by referring to these criteria.

  5. Comparative genomics of vesicomyid clam (Bivalvia: Mollusca chemosynthetic symbionts

    Directory of Open Access Journals (Sweden)

    Girguis Peter R

    2008-12-01

    Full Text Available Abstract Background The Vesicomyidae (Bivalvia: Mollusca are a family of clams that form symbioses with chemosynthetic gamma-proteobacteria. They exist in environments such as hydrothermal vents and cold seeps and have a reduced gut and feeding groove, indicating a large dependence on their endosymbionts for nutrition. Recently, two vesicomyid symbiont genomes were sequenced, illuminating the possible nutritional contributions of the symbiont to the host and making genome-wide evolutionary analyses possible. Results To examine the genomic evolution of the vesicomyid symbionts, a comparative genomics framework, including the existing genomic data combined with heterologous microarray hybridization results, was used to analyze conserved gene content in four vesicomyid symbiont genomes. These four symbionts were chosen to include a broad phylogenetic sampling of the vesicomyid symbionts and represent distinct chemosynthetic environments: cold seeps and hydrothermal vents. Conclusion The results of this comparative genomics analysis emphasize the importance of the symbionts' chemoautotrophic metabolism within their hosts. The fact that these symbionts appear to be metabolically capable autotrophs underscores the extent to which the host depends on them for nutrition and reveals the key to invertebrate colonization of these challenging environments.

  6. Assessment of thermo-mechanical behavior in CLAM steel first wall structures

    International Nuclear Information System (INIS)

    Liu Fubin; Yao Man

    2012-01-01

    Highlights: ► China Low Activation Martensitic steel (CLAM) as FW the structural material. ► The thermo-mechanical behavior of the FW was analyzed under the condition of normal ITER operation combined effect of plasma heat flux and neutron heating. ► The temperature dependence of the material physical properties of CLAM is summarized. - Abstract: The temperature and strain distributions of the mockup with distinct structural material (SS316L or China Low Activation Martensitic steel (CLAM)) in two-dimensional model were calculated and analyzed, based on a high heat flux (HHF) test recently reported with heat flux of 3.2 MW/m 2 . The calculated temperature and strain results in the first wall (FW), in which SS316L is as the structural material, showed good agreement with HHF test. By substituting CLAM steel for SS316L the contrast analysis indicates that the thermo-mechanical property for CLAM steel is better than that of SS316 at the same condition. Furthermore, the thermo-mechanical behavior of the FW was analyzed under the condition of normal ITER operation combined effect of plasma heat flux and neutron heating.

  7. Assessment of thermo-mechanical behavior in CLAM steel first wall structures

    Energy Technology Data Exchange (ETDEWEB)

    Liu Fubin, E-mail: liufubin_1216@126.com [School of Materials Science and Engineering, Dalian University of Technology, Dalian 116024, Liaoning (China); Yao Man, E-mail: yaoman@dlut.edu.cn [School of Materials Science and Engineering, Dalian University of Technology, Dalian 116024, Liaoning (China)

    2012-01-15

    Highlights: Black-Right-Pointing-Pointer China Low Activation Martensitic steel (CLAM) as FW the structural material. Black-Right-Pointing-Pointer The thermo-mechanical behavior of the FW was analyzed under the condition of normal ITER operation combined effect of plasma heat flux and neutron heating. Black-Right-Pointing-Pointer The temperature dependence of the material physical properties of CLAM is summarized. - Abstract: The temperature and strain distributions of the mockup with distinct structural material (SS316L or China Low Activation Martensitic steel (CLAM)) in two-dimensional model were calculated and analyzed, based on a high heat flux (HHF) test recently reported with heat flux of 3.2 MW/m{sup 2}. The calculated temperature and strain results in the first wall (FW), in which SS316L is as the structural material, showed good agreement with HHF test. By substituting CLAM steel for SS316L the contrast analysis indicates that the thermo-mechanical property for CLAM steel is better than that of SS316 at the same condition. Furthermore, the thermo-mechanical behavior of the FW was analyzed under the condition of normal ITER operation combined effect of plasma heat flux and neutron heating.

  8. Aquaculture Land-Use Policy: The Case of Clam Farming in Thaibinh Province, Vietnam

    Directory of Open Access Journals (Sweden)

    Thi Thu Hang NGO

    2016-12-01

    Full Text Available Policy-making and enforcement remains centralized in Vietnam. Policies have been formulated with less scientific and public justification, thus being largely bureaucratic and infeasible, and in many cases, they have created plagues for people at the grass-roots levels. This article focuses on the implementation of policies related to intertidal land-use and supports for clam farming in the Thaibinh province as a case study to explore the impacts of policies on clam farming and farmers. During the period of 2011–2013, provincial policies on intertidal land allocation and technical and financial supports had boosted clam farming development in the province to a surprising extent. Rapid expansion of the clam farming area has created significant consequences for the farming sector, as well as farmer’s lives. However, for the same provincial policies, but with different enforcement, different farming outcomes for clam farmers in the three study communes have resulted. Where farmers had more of a voice and choice in bidding for the intertidal areas they preferred, they faced fewer problems. It is, thus, suggested that a more decentralized policy-making and enforcement are needed, in which more scientific assessment and farmer participation are required to not only make government policy more successful in supporting farmers and achieving their expected outcomes, but also to provide farmers with more room to make their own farming decisions from which farming and marketing risks could be mitigated.

  9. Phylogenetic diversity and functional characterization of the Manila clam microbiota: a culture-based approach.

    Science.gov (United States)

    Leite, Laura; Jude-Lemeilleur, Florence; Raymond, Natalie; Henriques, Isabel; Garabetian, Frédéric; Alves, Artur

    2017-09-01

    According to the hologenome theory, the microbiota contributes to the fitness of the holobiont having an important role in its adaptation, survival, development, health, and evolution. Environmental stress also affects the microbiota and its capability to assist the holobiont in coping with stress factors. Here, we analyzed the diversity of cultivable bacteria associated with Manila clam tissues (mantle, gills, hemolymph) in two non-contaminated sites (Portugal and France) and one metal-contaminated site (Portugal). A total of 240 isolates were obtained. Representative isolates (n = 198) of the overall diversity were identified by 16S rDNA sequencing and subjected to functional characterization. Isolates affiliated with Proteobacteria, Actinobacteria, Firmicutes, and Bacteroidetes. Proteobacteria (mostly Pseudoalteromonadaceae and Vibrionaceae) were dominant in non-contaminated sites while Actinobacteria (mostly Microbacteriaceae) dominated in the metal-contaminated site. The main factor affecting the microbiota composition was contamination. No significant differences were observed between clam tissues and geographic regions. Several isolates tested positive for antibacterial activity, biofilm formation, protease, and siderophore production. The results show that the Manila clam harbors a diverse microbiota that may contribute to clam protection and overall fitness, as well as to its adaptation to stressful environments. In addition, the Manila clam microbiota is revealed as a promising source of novel probiotics with potential application in aquaculture.

  10. Impediment to Symbiosis Establishment between Giant Clams and Symbiodinium Algae Due to Sterilization of Seawater

    Science.gov (United States)

    Kurihara, Takeo; Yamada, Hideaki; Inoue, Ken; Iwai, Kenji; Hatta, Masayuki

    2013-01-01

    To survive the juvenile stage, giant clam juveniles need to establish a symbiotic relationship with the microalgae Symbiodinium occurring in the environment. The percentage of giant clam juveniles succeeding in symbiosis establishment (“symbiosis rate”) is often low, which is problematic for seed producers. We investigated how and why symbiosis rates vary, depending on whether giant clam seeds are continuously reared in UV treated or non treated seawater. Results repeatedly demonstrated that symbiosis rates were lower for UV treated seawater than for non treated seawater. Symbiosis rates were also lower for autoclaved seawater and 0.2-µm filtered seawater than for non treated seawater. The decreased symbiosis rates in various sterilized seawater suggest the possibility that some factors helping symbiosis establishment in natural seawater are weakened owing to sterilization. The possible factors include vitality of giant clam seeds, since additional experiments revealed that survival rates of seeds reared alone without Symbiodinium were lower in sterilized seawater than in non treated seawater. In conclusion, UV treatment of seawater was found to lead to decreased symbiosis rates, which is due possibly to some adverse effects common to the various sterilization techniques and relates to the vitality of the giant clam seeds. PMID:23613802

  11. Immune- and Pollution-mediated DNA Damage in Two Wild Mya arenaria Clam Populations

    Directory of Open Access Journals (Sweden)

    François Gagné

    2009-01-01

    Full Text Available In aquatic environments, genotoxicity results from the effects of pollution combined with the inflammatory response triggered by the immune system. Indeed, the production of nitrosylated DNA and proteins are though to arise from the production of peroxinitrite during phagocytosis and inflammation. The purpose of this study was to examine new DNA biomarkers that differentiate between immune- and pollution-mediated genotoxicity in wild clam populations. Intertidal clam populations were sampled and analyzed for gonadal DNA strand breaks, DNA nitrosylation and xanthine oxidoreductase (XOR activity (purine salvage pathway. The clam weight-to-shell-length ratio, the gonado-somatic index (GSI, age status, lipid peroxidation, xenobiotic conjugation activity (glutathione S-transferase (GST and phagocytic activity were examined to shed light on their relationships with the observed genotoxic endpoints. XOR activity and DNA strand breaks were generally elevated at polluted sites and correlated significantly with clam weight-to-shell-length ratios and DNA nitrosylation. DNA nitrosylation was also higher at some sites and correlated significantly with phagocytic activity and with DNA strand breaks. This study showed that DNA strand breaks were associated with both immune- and pollution-mediated effects. This suggests that there is a loss of DNA repair capacity due to the combined effects of aging, pollution and immune response in wild clam populations that are impacted by anthropogenic activity.

  12. Continuous water quality monitoring for the hard clam industry in Florida, USA.

    Science.gov (United States)

    Bergquist, Derk C; Heuberger, David; Sturmer, Leslie N; Baker, Shirley M

    2009-01-01

    In 2000, Florida's fast-growing hard clam aquaculture industry became eligible for federal agricultural crop insurance through the US Department of Agriculture, but the responsibility for identifying the cause of mortality remained with the grower. Here we describe the continuous water quality monitoring system used to monitor hard clam aquaculture areas in Florida and show examples of the data collected with the system. Systems recording temperature, salinity, dissolved oxygen, water depth, turbidity and chlorophyll at 30 min intervals were installed at 10 aquaculture lease areas along Florida's Gulf and Atlantic coasts. Six of these systems sent data in real-time to a public website, and all 10 systems provided data for web-accessible archives. The systems documented environmental conditions that could negatively impact clam survival and productivity and identified biologically relevant water quality differences among clam aquaculture areas. Both the real-time and archived data were used widely by clam growers and nursery managers to make management decisions and in filing crop loss insurance claims. While the systems were labor and time intensive, we recommend adjustments that could reduce costs and staff time requirements.

  13. Impediment to symbiosis establishment between giant clams and Symbiodinium algae due to sterilization of seawater.

    Science.gov (United States)

    Kurihara, Takeo; Yamada, Hideaki; Inoue, Ken; Iwai, Kenji; Hatta, Masayuki

    2013-01-01

    To survive the juvenile stage, giant clam juveniles need to establish a symbiotic relationship with the microalgae Symbiodinium occurring in the environment. The percentage of giant clam juveniles succeeding in symbiosis establishment ("symbiosis rate") is often low, which is problematic for seed producers. We investigated how and why symbiosis rates vary, depending on whether giant clam seeds are continuously reared in UV treated or non treated seawater. Results repeatedly demonstrated that symbiosis rates were lower for UV treated seawater than for non treated seawater. Symbiosis rates were also lower for autoclaved seawater and 0.2-µm filtered seawater than for non treated seawater. The decreased symbiosis rates in various sterilized seawater suggest the possibility that some factors helping symbiosis establishment in natural seawater are weakened owing to sterilization. The possible factors include vitality of giant clam seeds, since additional experiments revealed that survival rates of seeds reared alone without Symbiodinium were lower in sterilized seawater than in non treated seawater. In conclusion, UV treatment of seawater was found to lead to decreased symbiosis rates, which is due possibly to some adverse effects common to the various sterilization techniques and relates to the vitality of the giant clam seeds.

  14. Gene transcription and biomarker responses in the clam Ruditapes philippinarum after exposure to ibuprofen

    International Nuclear Information System (INIS)

    Milan, Massimo; Pauletto, Marianna; Patarnello, Tomaso; Bargelloni, Luca; Marin, Maria Gabriella; Matozzo, Valerio

    2013-01-01

    Pharmaceuticals are a class of emerging environmental contaminants that continuously enter aquatic environments. Presently, little information is available about the effects of these substances on non-target organisms, such as bivalves. We investigated the effects of ibuprofen (IBU) on the clam Ruditapes philippinarum. Clams were exposed for 1, 3, 5 and 7 days to 0, 100 and 1000 μg IBU/L, and established biomarker responses (haemolymph lysozyme, gill acetylcholinesterase and digestive gland superoxide dismutase activities) as well as digestive gland transcriptome were evaluated. A two-way ANOVA revealed significant effects of both “IBU concentration” and “exposure duration” on biomarker responses. Overall, the enzyme activities were generally lower in IBU-exposed clams than in controls. Although limited knowledge of the mollusc transcriptome makes it difficult to interpret the effects of IBU on clams, the gene transcription analysis using DNA microarrays enabled the identification of the putative molecular mode of action of the IBU. The functional analysis of differentially transcribed genes suggests that IBU can interfere with various signalling pathways in clams, such as arachidonic acid metabolism, apoptosis, peroxisomal proliferator-activated receptors, and nuclear factor-kappa B. In addition, several genes involved in the metabolism of xenobiotics (e.g., glutathione S-transferase, sulfotransferase, cytochrome P450) were also found to be significantly affected by IBU exposure. In summary, the integrated approach of gene transcription analysis and biomarker responses facilitated the elucidation of the putative mechanisms of action of IBU in non-target species.

  15. Distanced Data: Transcribing Other People's Research Tapes

    Science.gov (United States)

    Tilley, Susan A.; Powick, Kelly D.

    2004-01-01

    In this article, we report on our qualitative study involving eight individuals hired to transcribe research tapes in university contexts. We consider issues of data analysis and data trustworthiness and the implications for both when transcription is assigned to someone other than the researcher. We explore the challenges transcribers faced…

  16. Melt processing of Yb-123 tapes

    International Nuclear Information System (INIS)

    Athur, S. P.; Balachandran, U.; Salama, K.

    2000-01-01

    The innovation of a simple, scalable process for manufacturing long-length conductors of HTS is essential to potential commercial applications such as power cables, magnets, and transformers. In this paper the authors demonstrate that melt processing of Yb-123 tapes made by the PIT route is an alternative to the coated conductor and Bi-2223 PIT tape fabrication techniques. Ag-clad Yb-123 tapes were fabricated by groove rolling and subsequently, melt processed in different oxygen partial pressures in a zone-melting furnace with a gradient of 140 C/cm. The transition temperatures measured were found to be around 81 K undermost processing conditions. EPMA of the tapes processed under different conditions show the 123 phase to be Ba deficient and Cu and Yb rich. Critical current was measured at various temperatures from 77 K to 4.2 K. The J c increased with decrease in pO 2 . The highest I c obtained was 52 A at 4.2 K

  17. Localized leak detection utilizing moisture sensitive tape

    International Nuclear Information System (INIS)

    Riddle, P.

    1984-01-01

    Moisture sensitive tape (MST) has been used in various nuclear power plants to detect leaks in reactor piping systems. The sensor assembly consists of MST, transponder, and sensor carrier, and is installed on the exterior of thermal insulation. The components, applications, installation, and purchasing information are discussed in the paper

  18. Artificial Intelligence Controls Tape-Recording Sequence

    Science.gov (United States)

    Schwuttke, Ursula M.; Otamura, Roy M.; Zottarelli, Lawrence J.

    1989-01-01

    Developmental expert-system computer program intended to schedule recording of large amounts of data on limited amount of magnetic tape. Schedules recording using two sets of rules. First set incorporates knowledge of locations for recording of new data. Second set incorporates knowledge about issuing commands to recorder. Designed primarily for use on Voyager Spacecraft, also applicable to planning and sequencing in industry.

  19. "Space slitter" for film or tape

    Science.gov (United States)

    Johnson, W. H.

    1978-01-01

    Device cuts film or tape into strips by guiding film in channel under cutting blades. Device is operated by lifting pressure bar to insert blades into film. Film is then pulled through blades. Cutter has potential uses in advertising, commercial art, and publishing fields.

  20. Carbon Nanotube-Based Synthetic Gecko Tapes

    Science.gov (United States)

    Dhinojwala, Ali

    2008-03-01

    Wall-climbing geckos have unique ability to attach to different surfaces without the use of any viscoelastic glues. On coming in contact with any surface, the micron-size gecko foot-hairs deform, enabling molecular contact over large areas, thus translating weak van der Waals (vdW) interactions into enormous shear forces. We will present our recent results on the development of synthetic gecko tape using aligned carbon nanotubes to mimic the keratin hairs found on gecko feet. The patterned carbon nanotube-based gecko tape can support a shear stress (36 N/cm^2) nearly four times higher than the gecko foot and sticks to a variety of surfaces, including Teflon. Both the micron-size setae (replicated by nanotube bundles) and nanometer-size spatulas (individual nanotubes) are necessary to achieve macroscopic shear adhesion and to translate the weak vdW interactions into high shear forces. The carbon nanotube based tape offers an excellent synthetic option as a dry conductive reversible adhesive in microelectronics, robotics and space applications. The mechanism behind these large shear forces and self-cleaning properties of these carbon nanotube based synthetic gecko tapes will be discussed. This work was performed in collaboration with graduate students Liehui Ge, and Sunny Sethi, and collaborators from RPI; Lijie Ci and Professor Pulickel Ajayan.

  1. Long-Term Surveys Show Invasive Overbite Clams (Potamocorbula amurensis are Spatially Limited in Suisun Marsh, California

    Directory of Open Access Journals (Sweden)

    Jason Baumsteiger

    2017-07-01

    Full Text Available https://doi.org/10.15447/sfews.2017v15iss2art6The overbite clam (Potamocorbula amurensis is a major invasive species in the San Francisco Estuary, California, and has been implicated in the decline of pelagic productivity and native fish species. Little is known of its impact on Suisun Marsh, a large brackish tidal region of the estuary. We looked at the abundance and spatial distribution of clams in the marsh, including examining the influence of water quality, using long-term (1988–2015 otter trawl surveys. Temporal trends indicated that overbite clam abundance has been increasing, but adult clams were spatially restricted to a single large slough (Suisun. Clams were absent from most interior channels, limiting their overall effect on the marsh aquatic ecosystem. Abiotic variables, particularly salinity, proved important predictors of overbite clam abundance, although the variables examined alone could not explain overbite clam distributions. We propose that connectivity, detritus loads, and/or predation pressure may work in conjunction with abiotic variables to cause poor survival rates for recruits in interior marsh sites, keeping the distribution limited. Overall results are encouraging for restoration projects in brackish tidal marshes that need to deal with overbite clams.

  2. Effect of binder concentration and blade gap on Yttria stabilized Zirconia tapes obtained by tape casting

    Energy Technology Data Exchange (ETDEWEB)

    Mena Garcia, J.; Reyes Rojas, A.; Rodriguez Gonzalez, C.A.; Hernandez Paz, J.; Garcia Casillas, P.E.; Enriquez Carrejo, J.L.; Camacho Montes, H.

    2016-07-01

    The tape casting method has kept its interest over the years due to the wide spectrum of its applications and its economic viability in comparison to other techniques focused on micrometric thin films. Two key parameters for tape casting are the binder relative amount and the Dr. Blade gap. The binder relative amount has a strong influence on the rheological properties for the ceramic YSZ slurry (ethanol, butanone, TEA, PVB, PEG, DEP). The coefficient K and the exponent m of the Cross model are reported to be inside the ranges 152.25-231.12 and 0.00987-0.26646 for PVB binder weight percentage concentrations between 6% and 12%. It is possible to describe the ceramic tape thickness dependence by means of a linear relation depending on the Dr. Blade gap whose linear coefficients (slope) are equal to 0.0350 and 0.2171 for green and sintered tapes respectively, with the YSZ slurry of the present work. (Author)

  3. Effect of kinesio-taping on ankle joint stability

    Directory of Open Access Journals (Sweden)

    Mervat A. Mohamed

    2016-05-01

    Full Text Available Ankle Instability is characterized by recurrent giving way and often develops after repeated lateral ankle sprains. Kinesiotape is more elastic than traditional athletic tape and is becoming increasingly popular. It is reported to decrease pain, improve muscle function, circulation and proprioception, however, research examining the effects of Kinesiotape in ankle instability is limited. The objective of this study was to determine if applying Kinesiotape to unstable ankle may improve performance in the Star Excursion Balance Test (SEBT, which has been shown to be a sensitive and reliable measure for quantifying dynamic balance. Thirty subjects with first degree ankle sprain were participated in this study. SEBT was used to test the subject dynamic balance under three conditions; without taping, with white athletic tape and with kinesiotape. One way repeated measure ANOVA using Greenhouse-Geisser corrections were conducted to evaluate differences in SEBT for the three conditions. Pairwise comparison of the outcome measures in the three occasions (without taping, with athletic taping, and with kinesio taping revealed statistically significant differences of all outcomes between occasion 1 (without taping and occasion 2 (with athletic taping favoring the athletic taping (p < 0.05. Also, a statistically significant difference between occasion 1 (without taping and occasion 3 (with kinesio taping were found (p < 0.05 favoring kinesio taping. Moreover, pairwise comparison of the ankle stability outcomes using athletic taping versus kinesio taping indicated a statistically significant difference (p < 0.05 in favor of kinesio taping measures. Conclusion: kinesiotape has superior effect than athletic tape in patients with first degree ankle sprain and can be used safely for improving ankle joint stability.

  4. Review on the Risk Assessment of Heavy Metals in Malaysian Clams

    Directory of Open Access Journals (Sweden)

    Md. Faruk Hossen

    2015-01-01

    Full Text Available The current review discusses the levels of six heavy metals in different clam species from 34 sites of Malaysian coasts. The concentrations (µg/g dry weight of these heavy metals ranged around 0.18–8.51, 0.13–17.20, 2.17–7.80, 0.84–36.00, 24.13–368.00, and 177.82–1912.00 for Cd, Pb, Ni, Cu, Zn, and Fe, respectively. It was observed that the concentrations of metals slightly depend on different clam species but mostly depend on site locations. According to Malaysian Food Regulation (1985, about 30% and more than 50% sites are safe from Cd and Pb contamination, respectively, and also the clam species from the other populations studied were safe for consumption.

  5. Numerical simulation and experimental study of CLAM T-shapes for fusion applications by hydroforming

    International Nuclear Information System (INIS)

    Guo Xunzhong; Tao Jie; Liu Hongbing; Li Ming

    2010-01-01

    The integral hydroforming process to prepare CLAM T-shapes for fusion applications was evaluated by means of numerical simulation. The paper firstly investigated the effect of different paths on the protrusion height and distribution of thickness thinning rate of T-shapes. Then, it discussed that the friction coefficient between die and tube blank played an important role in manufacturing high quality T-shapes. Subsequently, the practical hydroforming was performed based on the simulation results with the aid of special lubrication coatings with friction coefficient 0.07. It is obviously indicated that the simulation results agree well with the experimental ones in geometry size and wall thickness distribution. The results indicate that the numerical simulation guides the practical hydroforming of CLAM tube effectively and determines the actual cold forming process parameters rapidly. The sound CLAM T-shapes with proper geometry size and thickness distribution can be obtained by the optimal hydroforming process. (authors)

  6. Occurrence of antibiotics in mussels and clams from various FAO areas.

    Science.gov (United States)

    Chiesa, Luca Maria; Nobile, Maria; Malandra, Renato; Panseri, Sara; Arioli, Francesco

    2018-02-01

    Filter feeders, like mussels and clams, are suitable bioindicators of environmental pollution. These shellfish, when destined for human consumption, undergo a depuration step that aims to nullify their pathogenic microorganism load and decrease chemical contamination. Nevertheless, the lack of contamination by drugs may not be guaranteed. Antimicrobials are a class of drugs of particular concern due to the increasing phenomenon of antibiotic resistance. Their use in breeding and aquaculture is a major cause of this. We developed a multiclass method for the HPLC-MS/MS analysis of 29 antimicrobials, validated according to the Commission Decision 2002/657/UE guidelines, and applied it to 50 mussel and 50 clam samples derived from various Food and Agricultural Organisation marine zones. The results obtained, indicate a negligible presence of antibiotics. Just one clam sample showed the presence of oxytetracycline at a concentration slightly higher than the European Union Maximum residue limit set for fish. Copyright © 2017. Published by Elsevier Ltd.

  7. Environmental context and trophic trait plasticity in a key species, the tellinid clam Macoma balthica L

    DEFF Research Database (Denmark)

    Törnroos, Anna; Nordström, M. C.; Aarnio, K.

    2015-01-01

    Species show varying levels of plasticity regarding morphology, physiology and behaviour in relation to their immediate environment, and several trait characteristics are habitat-dependent. Determining when and how the environmental context changes trait expression is of key importance...... for understanding the role of individual species for ecosystem functioning. The tellinid clam Macoma balthica can vary its feeding behaviour, shifting between deposit- and suspension-feeding. In order to study the context-dependency of this trophic plasticity in adult clams, we conducted an experiment assessing...... food uptake by using stable isotope signatures (delta C-13 and delta N-15). We transplanted individuals between and within two shallow bays differing in exposure (exposed sheltered) and sediment characteristics. Our results show that isotope signatures of clams differed between the two habitats...

  8. Clam bioaccumulation of Alkylphenols and Polyciclic aromatic hydrocarbons in the Venice lagoon under different pressures.

    Science.gov (United States)

    Ademollo, N; Patrolecco, L; Matozzo, V; Marin, M G; Valsecchi, S; Polesello, S

    2017-11-15

    Biota-Sediment Accumulation Factors (BSAFs) of nonylphenols (NPs) and polycyclic aromatic hydrocarbons (PAHs) in Ruditapes philippinarum from the Venice Lagoon (Italy) were determined with the aim to verify whether the routine biomonitoring studies are reliable in contaminated sites. Clams and sediments were collected in field campaigns (October 2003 to June 2004) in three sites of the Venice Lagoon. Results showed that Marghera and Campalto sediments were more contaminated by NPs and PAHs than Poveglia. Different trends were observed in the contamination of clams with the highest BSAFs found at Poveglia. BSAF trend appeared to be inversely related to the contaminant pressure on the sites. These results suggest that clam bioaccumulation is not always representative of the chemical pressure on aquatic biota. The direct correlation between sediment and biota concentrations in contaminated sites can be lost as a function of the site-specific conditions such as sediment toxicity and food availability. Copyright © 2017 Elsevier Ltd. All rights reserved.

  9. Review on the Risk Assessment of Heavy Metals in Malaysian Clams.

    Science.gov (United States)

    Hossen, Md Faruk; Hamdan, Sinin; Rahman, Md Rezaur

    2015-01-01

    The current review discusses the levels of six heavy metals in different clam species from 34 sites of Malaysian coasts. The concentrations (µg/g dry weight) of these heavy metals ranged around 0.18-8.51, 0.13-17.20, 2.17-7.80, 0.84-36.00, 24.13-368.00, and 177.82-1912.00 for Cd, Pb, Ni, Cu, Zn, and Fe, respectively. It was observed that the concentrations of metals slightly depend on different clam species but mostly depend on site locations. According to Malaysian Food Regulation (1985), about 30% and more than 50% sites are safe from Cd and Pb contamination, respectively, and also the clam species from the other populations studied were safe for consumption.

  10. Effect of coastal eutrophication on heavy metal bioaccumulation and oral bioavailability in the razor clam, Sinonovacula constricta

    International Nuclear Information System (INIS)

    Tu, Tengxiu; Li, Shunxing; Chen, Lihui; Zheng, Fengying; Huang, Xu-Guang

    2014-01-01

    Graphical abstract: - Highlights: • Razor clams are often exposed to coastal eutrophication. • The bioaccumulation of Fe, Ni, V, and As was promoted by eutrophication. • Bionic gastrointestinal tract was used for metal oral bioavailability assessment. • Eutrophication decreased oral bioavailability of Fe and Pb but enhanced for V. • The daily maximum allowable intakes are controlled by eutrophication levels. - Abstract: As traditional seafoods, the razor clams are widely distributed from tropical to temperate areas. Coastal razor clams are often exposed to eutrophication. Heavy metal contamination is critical for seafood safety. However, how eutrophication affects bioaccumulation and oral bioavailability of heavy metals in the razor clams is unknown. After a four-month field experimental cultivation, heavy metals (Fe, Cu, Ni, V, As, and Pb) could be bioaccumulated by the razor clams (Sinonovacula constricta) through exposure to metals present in water and sediments or in the food chain, and then transferred to human via consumption of razor clams. Bionic gastrointestinal digestion and monolayer liposome extraction are used for metal oral bioavailability (OBA) assessment. The influence of eutrophication on OBA is decreased for Fe and Pb and increased for V. A significant positive linear correlation was observed between the bioaccumulation factors of Fe, Ni, V, and As in razor clams and the coastal eutrophication. These results may be due to the effect of eutrophication on metal species transformation in coastal seawater and subcellular distribution in razor clams. The maximum allowable daily intakes of razor clams are controlled by eutrophication status and the concentration of affinity-liposome As in razor clams

  11. Effect of coastal eutrophication on heavy metal bioaccumulation and oral bioavailability in the razor clam, Sinonovacula constricta

    Energy Technology Data Exchange (ETDEWEB)

    Tu, Tengxiu [College of Chemistry and Environment, Minnan Normal University, Zhangzhou 363000 (China); Li, Shunxing, E-mail: lishunxing@mnnu.edu.cn [College of Chemistry and Environment, Minnan Normal University, Zhangzhou 363000 (China); Fujian Province Key Laboratory of Modern Analytical Science and Separation Technology (China); Chen, Lihui [College of Chemistry and Environment, Minnan Normal University, Zhangzhou 363000 (China); Zheng, Fengying; Huang, Xu-Guang [College of Chemistry and Environment, Minnan Normal University, Zhangzhou 363000 (China); Fujian Province Key Laboratory of Modern Analytical Science and Separation Technology (China)

    2014-10-15

    Graphical abstract: - Highlights: • Razor clams are often exposed to coastal eutrophication. • The bioaccumulation of Fe, Ni, V, and As was promoted by eutrophication. • Bionic gastrointestinal tract was used for metal oral bioavailability assessment. • Eutrophication decreased oral bioavailability of Fe and Pb but enhanced for V. • The daily maximum allowable intakes are controlled by eutrophication levels. - Abstract: As traditional seafoods, the razor clams are widely distributed from tropical to temperate areas. Coastal razor clams are often exposed to eutrophication. Heavy metal contamination is critical for seafood safety. However, how eutrophication affects bioaccumulation and oral bioavailability of heavy metals in the razor clams is unknown. After a four-month field experimental cultivation, heavy metals (Fe, Cu, Ni, V, As, and Pb) could be bioaccumulated by the razor clams (Sinonovacula constricta) through exposure to metals present in water and sediments or in the food chain, and then transferred to human via consumption of razor clams. Bionic gastrointestinal digestion and monolayer liposome extraction are used for metal oral bioavailability (OBA) assessment. The influence of eutrophication on OBA is decreased for Fe and Pb and increased for V. A significant positive linear correlation was observed between the bioaccumulation factors of Fe, Ni, V, and As in razor clams and the coastal eutrophication. These results may be due to the effect of eutrophication on metal species transformation in coastal seawater and subcellular distribution in razor clams. The maximum allowable daily intakes of razor clams are controlled by eutrophication status and the concentration of affinity-liposome As in razor clams.

  12. Microstructure and nanoindentation of the CLAM steel with nanocrystalline grains under Xe irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Yongqin, E-mail: chang@ustb.edu.cn; Zhang, Jing; Li, Xiaolin; Guo, Qiang; Wan, Farong; Long, Yi

    2014-12-15

    This work presents an early look at irradiation effects on China low activation martensitic (CLAM) steel with nanocrystalline grains (NC-CLAM steels) under 500 keV Xe-ion bombardment at room temperature to doses up to 5.3 displacements per atom (dpa). The microstructure in the topmost region of the steel is composed of nanocrystalline grains with an average diameter of 13 nm. As the samples were implanted at low dose, the nanocrystalline grains had martensite lath structure, and many dislocations and high density bubbles were introduced into the NC-CLAM steels. As the irradiation dose up to 5.3 dpa, a tangled dislocation network exists in the lath region, and the size of the bubbles increases. X-ray diffraction results show that the crystal quality decreases after irradiation, although the nanocrystals obviously coarsen. Grain growth under irradiation may be ascribed to the direct impact of the thermal spike on grain boundaries in the NC-CLAM steels. In irradiated samples, a compressive stress exists in the surface layer because of grain growth and irradiation-introduced defects, while the irradiation introduced grain-size coarsening and defects gradients from the surface to matrix result in a tensile stress in the irradiated NC-CLAM steels. Nanoindentation was used to estimate changes in mechanical properties during irradiation, and the results show that the hardness of the NC-CLAM steels increases with increasing irradiation dose, which was ascribed to the competition between the grain boundaries and the irradiation-introduced defects.

  13. An overview of the welding technologies of CLAM steels for fusion application

    Energy Technology Data Exchange (ETDEWEB)

    Chen Xizhang, E-mail: kernel.chen@gmail.com [School of Materials Science and Engineering, Jiangsu University, ZhenJiang, Jiangsu 212013 (China); Huang Yuming [School of Materials Science and Engineering, Jiangsu University, ZhenJiang, Jiangsu 212013 (China); Madigan, Bruce [Montana Tech. of University of Montana, Butte, MT 59701 (United States); Zhou Jianzhong [School of Mechanical Engineering, Jiangsu University, ZhenJiang, Jiangsu 221013 (China)

    2012-09-15

    Highlights: Black-Right-Pointing-Pointer Welding technologies of China Low Activation Martensitic steel is overviewed. Black-Right-Pointing-Pointer Most welding technologies in use are discussed and suggestions are given. Black-Right-Pointing-Pointer Proper welding technologies could ensure weld properties but more detailed work are necessary. - Abstract: China Low Activation Martensitic steel (CLAMs), a kind of RAFM steel with Chinese intellectual property rights, is considered as the primary structural material for the China-designed ITER test blanket module (TBM). As one of the key issues in the fabrication of the fusion reactor, the welding technologies of CLAMs are reviewed. Emphasis is placed on the weldability of CLAMs by different welding methods, and on the properties of as-welded and post-weld heat-treated joints. Recent highlights in research and development for the welding of CLAMs show that proper welding procedure could provide welds with adequate tensile strength but the welds exhibit lower impact toughness compared with the base metal. Post-weld heat treatment (PWHT) and the application of ultrasonic energy during TIG welding could dramatically improve impact toughness. Research also shows that welds in CLAMs have sufficient resistance to swelling under irradiation as well as suitable compatibility with liquid LiPb. The microstructure, mechanical and other physical properties of welds are significantly different from those of the base metal due to the complicated welding thermal cycle. The weld joint is the area most likely to fail one or more of the design requirements within the fusion reactor. Therefore significant additional research is necessary to ensure safe application of welded CLAM steel for fusion reactor construction.

  14. EFFECT OF KINESIO TAPE VERSUS ATHLETIC TAPE ON MYOELECTRIC ACTIVITY OF ANKLE MUSCLES IN PATIENTS WITH CHRONIC ANKLE SPRAIN

    Directory of Open Access Journals (Sweden)

    Asmaa F Abdelmonem

    2018-04-01

    Full Text Available Background: Sprained ankle a common orthopedic injury. The standard treatment for ankle sprains remains nonoperative. Ankle taping was used to protect and prevent ligaments excessive strain. So, the current study aimed at investigating the effect of spa-care Kinesio tape versus standard white athletic tape on myoelectric activities (EMG of ankle evertors (peroneus longus and invertors (tibialis anterior in a chronic ankle sprain. Methods: A convenient sample of 30 patients with a chronic ankle sprain (18 females and 12 males were included in this study. Their mean age ±SD was 24 ±1.2 years. Their height was 175±4.8 cm among men & 163±5.2 cm for females, and weight was 85±5.2 kg for males & 74±5.5 kg for women. It was a within-group design in which the same participant experienced the two types of taping compared to no taping condition. Root mean square (RMS was measured while participants were moving the isokinetic dynamometer at an angular velocity of 120°/sec using concentric contraction mode through full ankle range of motion. The EMG (RMS of evertors and invertors was measured immediately after the three taping ways (no tape, Kinesio tape, and athletic tape with a one-week interval between each taping. Results: Spa-care Kinesiotape significantly reduced evertors and invertors EMG (RMS compared with no tape or athletic tape in patients with chronic ankle sprain. Mean± SD of the evertors was 0.7 (±0.1 for no tape and 0.58 (±0.2 for Kinesio tape. The P value was 0.000 for kinesio tape in evertors compared with no tape. Also, mean± SD of the invertors was 0.87 (±0.23 for no tape, and 0.54 (±0.1 for Kinesio tape and the P value was 0.001 for Kinesio tape in invertors compared with no tape. Conclusion: Spa-care Kinesio tape may be useful for reducing EMG activity of ankle muscles in a chronic ankle sprain.

  15. Methods and systems for fabricating high quality superconducting tapes

    Energy Technology Data Exchange (ETDEWEB)

    Majkic, Goran; Selvamanickam, Venkat

    2018-02-13

    An MOCVD system fabricates high quality superconductor tapes with variable thicknesses. The MOCVD system can include a gas flow chamber between two parallel channels in a housing. A substrate tape is heated and then passed through the MOCVD housing such that the gas flow is perpendicular to the tape's surface. Precursors are injected into the gas flow for deposition on the substrate tape. In this way, superconductor tapes can be fabricated with variable thicknesses, uniform precursor deposition, and high critical current densities.

  16. Experimental Tape Casting of Adjacently Graded Materials for Magnetic Refrigeration

    DEFF Research Database (Denmark)

    Bulatova, Regina

    encompass modification of the entire tape caster into a multi chamber unit, establishment of the optimal operating parameters such as casting gap, speed, and slurry level in the tape caster reservoir, and elucidation of the impact of chamber partition design on the quality of the final tape. The second...... of the side-by-side tape casting technique: recognising critical parameters which affect the quality of a graded tape, shape and position of the interface area. Studied parameters can be divided into two categories: operational parameters and slurry formulation optimisation. The operational parameters...

  17. Transmission electron microscopy investigation of Bi-2223/Ag tapes

    DEFF Research Database (Denmark)

    Andersen, L.G.; Bals, S.; Tendeloo, G. Van

    2001-01-01

    during the tape processing, (3) a study of the grain boundaries on an atomic scale, including intergrowth investigations. Tapes with different process parameters have been compared with respect to the microstructure. A fully processed tape has on the average 50% thicker Bi-2223 grains than a tape after......The microstructure of (Bi,Pb)(2)Sr2Ca2CuOx (Bi-2223) tapes has been investigated by means of transmission electron microscopy (TEM) and high-resolution TEM. The emphasis has been placed on: (1) an examination of the grain morphology and size, (2) grain and colony boundary angles, which are formed...

  18. Use of video taping during simulator training

    International Nuclear Information System (INIS)

    Helton, M.; Young, P.

    1987-01-01

    The use of a video camera for training is not a new idea and is used throughout the country for training in such areas as computers, car repair, music and even in such non-technical areas as fishing. Reviewing a taped simulator training session will aid the student in his job performance regardless of the position he holds in his organization. If the student is to be examined on simulator performance, video will aid in this training in many different ways

  19. The four silo STK Powderhorn Tape Library

    CERN Multimedia

    Patrice Loïez

    2001-01-01

    A view of the four silo Storage Tek (STK) Powderhorn Tape Library and its control area. Each silo can contain up to 6000 storage slots with cartridges of 10, 20, 25 or 50 GB capacity, reaching a data transfer rate of up to 12 Mbytes/sec. This will form part of the Grid system that will process the huge amounts of data produced at the LHC.

  20. Perceived Organizational Red Tape and Organizational Performance in Public Services

    DEFF Research Database (Denmark)

    Jacobsen, Christian Bøtcher; Jakobsen, Mads Leth

    2018-01-01

    The claim that perceived organizational red tape hampers public services has become a central theme in public administration research. Surprisingly, however, few scholars have empirically examined the impact of perceived red tape on organizational performance. This study empirically analyzes how...... perceived organizational red tape among managers and frontline staff relates to objectively measured performance. The data consists of survey responses from teachers and principals at Danish upper secondary schools combined with grade-level administrative performance data. Based on theories of red tape...... and motivation crowding, we hypothesize that perceived organizational red tape reduces performance within such organizations. The empirical result is a small, negative relationship between staff perception of red tape and performance, and no relationship between manager-perceived red tape and performance....

  1. Transaction aware tape-infrastructure monitoring

    International Nuclear Information System (INIS)

    Nikolaidis, Fotios; Kruse, Daniele Francesco

    2014-01-01

    Administrating a large scale, multi protocol, hierarchical tape infrastructure like the CERN Advanced STORage manager (CASTOR)[2], which stores now 100 PB (with an increasing step of 25 PB per year), requires an adequate monitoring system for quick spotting of malfunctions, easier debugging and on demand report generation. The main challenges for such system are: to cope with CASTOR's log format diversity and its information scattered among several log files, the need for long term information archival, the strict reliability requirements and the group based GUI visualization. For this purpose, we have designed, developed and deployed a centralized system consisting of four independent layers: the Log Transfer layer for collecting log lines from all tape servers to a single aggregation server, the Data Mining layer for combining log data into transaction context, the Storage layer for archiving the resulting transactions and finally the Web UI layer for accessing the information. Having flexibility, extensibility and maintainability in mind, each layer is designed to work as a message broker for the next layer, providing a clean and generic interface while ensuring consistency, redundancy and ultimately fault tolerance. This system unifies information previously dispersed over several monitoring tools into a single user interface, using Splunk, which also allows us to provide information visualization based on access control lists (ACL). Since its deployment, it has been successfully used by CASTOR tape operators for quick overview of transactions, performance evaluation, malfunction detection and from managers for report generation.

  2. Enhancing the low-level tape layer of CERN Tape Archive software

    CERN Document Server

    AUTHOR|(CDS)2160814; Ruse, Laura Cristina; Vasilescu, Laura

    CERN manages the largest scientific data archive in the HEP domain. The archive currently holds over 180 Petabytes, with forecasts of up to 100PB of new data added per year. Considering this numbers, the most cost-effective solution for storage in terms of capacity and maintenance is represented by magnetic tapes. The drawback of this solution is the access time which can raise to several minutes for a series of files. In an environment where very large volumes of physics data are being traded from tape to disk and vice versa, this issue becomes a serious performance bottleneck. This thesis introduces two low-level tape access optimizations: first, adding support for the Recommended Access Order (RAO), a mechanism offered by the tape hardware infrastructure to compute the file order corresponding to the minimum access time. We will present our solution for including RAO in the file retrieval operations in CERN tape archive software in order to benefit from the reduced reading time. The second optimization ...

  3. Ten-month recolonization of the k-area cooling water system by the Asiatic clam Corbicula fluminea

    International Nuclear Information System (INIS)

    Harvey, R.S.

    1978-01-01

    The Asiatic clam Corbicula fluminea was found in the Savannah River near Augusta, Georgia, in 1973. In 1975, Corbicula clogged heat exchangers and caused a shutdown of P Reactor, one of three operating nuclear production reactors (P, K, and C) at the Savannah River Plant (SRP). Clams were subsequently removed from K-Area and C-Area cooling water systems. At K Area, large volumes of river water are discharged into three 23-megaliter basins (Figure 1) where some settling occurs before the water is pumped through heat exchangers in the reactor area. The deposited silt provides a suitable substrate for Corbicula growth and reproduction. The silt must be removed at regular inervals to prevent heat exchanger pluggage arising from high populations of clams in the basins. The 186 basins at K Area were sampled to determine: the buildup of the Corbicula population since the basins were last cleaned, the size/age distribution of the clam population, and the occurrence of clam larvae. In addition, debris from flushes of Emergency Cooling Water Headers CW-39 and RW-1 were analyzed to determine: the relative abundance of live and dead clams, the size/age distribution of clams, and the volume of individual debris components

  4. Uptake and release of paralytic shellfish toxins by the clam Ruditapes decussatus exposed to Gymnodinium catenatum and subsequent depuration.

    Science.gov (United States)

    Botelho, Maria João; Vale, Carlos; Grilo, Rita Velez; Ferreira, João Gomes

    2012-06-01

    A laboratory experiment was performed with the clam Ruditapes decussatus, fed with the toxic dinoflagellate Gymnodinium catenatum and the non-toxic algae Isochrysis galbana (14 days) and subsequently only with I. galbana (15 days). Individual paralytic shellfish toxins were determined by LC-FLD in G. catenatum cells, whole clam tissues, and particulate organic matter (POM) produced by clams. The toxins dcSTX and dcGTX2 + 3 in the algae were less abundant than C1 + 2 and B1, but were predominant in clams during both the exposure and depuration phases. The toxin dcNEO was only detected in clams during a short period, indicating conversion from other compounds. The toxin composition of the POM indicated the export of dcSTX as faeces or pseudo-faeces along the entire experiment (2.5-14 nmol mg(-1)), B1 was present in a short period of the exposure and C1 + 2 and dcGTX2 + 3 absent. A mass balance calculation indicated that approximately 95% of C1 + 2 and 85% of B1 supplied to the clams were converted into other toxins or lost in solution. Conversely, the net gain of 512, 61 and 31 nmol for dcSTX, dcGTX2 + 3 and dcNEO, respectively, suggests the conversion from other assimilated compounds by clams during exposure and depuration phases. Copyright © 2012 Elsevier Ltd. All rights reserved.

  5. Direct contribution of clams (Ruditapes philippinarum) to benthic fluxes, nitrification, denitrification and nitrous oxide emission in a farmed sediment

    Science.gov (United States)

    Welsh, David T.; Nizzoli, Daniele; Fano, Elisa A.; Viaroli, Pierluigi

    2015-03-01

    The influence of the manila clam (Ruditapes philippinarum) on N-cycle processes, and oxygen and nutrient fluxes in a farmed sediment was investigated using a multiple core incubation approach and parallel incubations of individual clams. Clam population/biomass density varied ∼8-fold between cores and all sediment-water column solute (O2. N2, N2O, NH4+, NOX and DIN) fluxes and benthic process (N-regeneration, nitrification and denitrification) rates were strongly and significantly correlated with clam density/biomass. Isolated clams exhibited high rates of respiration, N-excretion, nitrification and denitrification of 2050 ± 70, 395 ± 49, 201 ± 42 and 235 ± 40 nmol individual-1 h-1, respectively. The direct contribution of the clams and their associated microbiota to benthic processes was estimated by multiplying the per individual rates by the number of clams in each incubated core. The clams on average directly accounted for 64-133% of total rates of sediment oxygen demand, N-regeneration, nitrification and denitrification, indicating that they regulated processes primarily through their own metabolic activity and that of bacteria that colonise them. Clams and the farmed sediments were significant sources of the greenhouse gas N2O, but this was primarily due to their high nitrification and denitrification rates, rather than high specific N2O yields, as N2O emissions represented farmed sediments had a high denitrification efficiency of 67 ± 10%, but this ecosystem service came at the environmental cost of increased N-regeneration and N2O emission rates. The measured N2O emissions indicate that bivalve aquaculture may be a significant source of N2O. It is therefore recommended that N2O emissions should be included in the impact assessments of current and future bivalve-farming projects.

  6. The clam (Chamelea gallina: evaluation of the effects of solids suspended in seawater on bivalve molluscs

    Directory of Open Access Journals (Sweden)

    Salvatora Angela Angioni

    2010-03-01

    Full Text Available The study was designed to evaluate the effects of solids in suspension in seawater on clams (Chamelea gallina. The aim was to investigate the possible correlation between the widespread deaths of clams in the coastal waters of the central and northern Adriatic in the last five years and increased concentrations of solids in suspension. The research involved conducting 96-hour tests on clams farmed in aquariums containing filtered seawater. The tests were preceded by a 7-day adaptation stage to allow the molluscs to acclimatise. During this period, the clams were fed on unicellular seaweed (Dunaliella tertiolecta. The molluscs were exposed to particles of solids in suspension consisting of pools of silica gel (SiO2 granules of various sizes, similar to those constituting silt, whose presence and suspension in the sea considerably increase after heavy rain and heavy seas. The study established that the number of deaths caused by solids suspended in seawater at the concentrations used in the tests was not statistically significant.

  7. Allometric relationships in the bioconcentration of heavy metals by the edible tropical clam Gafrarium tumidum

    International Nuclear Information System (INIS)

    Hedouin, L.; Metian, M.; Teyssie, J.-L.; Fowler, S.W.; Fichez, R.; Warnau, M.

    2006-01-01

    Although metal contamination is a problem of major concern in the lagoon of New Caledonia due to intense mining activities conducted on land, very little is known on the metal ecotoxicology of local marine organisms. The clam Gafrarium tumidum was investigated to assess its usefulness as a bioindicator species of metal contamination in this lagoon. More particularly, allometric relationships between metal accumulation and clam size were determined for five common metals in New Caledonian lagoon waters (Cd, Cr, Co, Zn and Ag) using a highly sensitive radiotracer technique. Experimental results showed that allometric relationships were dependent on the element and on the body compartment considered. As a rule, allometric relationships of metal concentration factor were more pronounced in shell than in soft parts. Significant relationships with clam size for Cd, Cr, Co and Zn followed inverse power functions. In contrast, the degree of Ag bioaccumulation was positively correlated with size. In view of the literature on Ag in bivalves, the latter observation suggests the occurrence of a specific detoxification mechanism (sequestration) that would be more efficient in old individuals. Overall, the experimental results indicate that the use of G. tumidum as a bioindicator in monitoring programmes requires selecting individuals of a specific size range in order to obtain comparable information about ambient metal levels. Since the size effect is greatest among smaller individuals, it is recommended to select clams with a shell width greater than 35 mm

  8. Allozyme electrophoresis as a tool for distinguishing different zooxanthellae symbiotic with giant clams

    Science.gov (United States)

    Baillie, B. K.; Monje, V.; Silvestre, V.; Sison, M.; Belda-Baillie, C. A.

    1998-01-01

    The taxonomy of zooxanthellae in marine invertebrate symbioses is not well understood owing mainly to their lack of reliable morphological differences. Nevertheless, previous work using protein and DNA electrophoreses has set the stage for advancing our taxonomic understanding of cnidarian zooxanthellae. Here we present the use of allozymes as genetic markers for distinguishing algal isolates from tridacnid hosts. Zooxanthellae from seven Tridacna and Hippopus species were isolated and maintained in axenic clonal cultures over many generations. Of 16 enzyme systems, α- and β-esterase (EST), esterase-F (EST-F), glucose phosphate isomerase (GPI), and malate dehydrogenase (MDH) were found suitable polymorphic markers of genetic differences among clonal cultures. Of 39 clonal isolates, 97% were found to be genetically distinguishable. This high extent of genetic variation in zooxanthellae within and between clam species was unexpected, and is difficult to explain based solely on the general notion of asexual reproduction in symbiotic zooxanthellae. Our results are also consistent with the occurrence of sexual reproduction in clam zooxanthellae. The close genetic similarity of the symbionts of Tridacna gigas, the largest and fastest-growing clam species, and the difficulty of initiating their clonal cultures in the given nutrient medium, compared with the symbionts of other clam species, are further indicative of possibly distinct algal symbionts in T. gigas. These findings are discussed in light of current taxonomic understanding of these organisms.

  9. CLAM - CoLlAborative eMbedded networks for submarine surveillance: An overview

    NARCIS (Netherlands)

    Meratnia, Nirvana; Havinga, Paul J.M.; Casari, Paolo; Petrioli, Chiara; Grythe, Knut; Husoy, Thor; Zorzi, Michele

    2011-01-01

    This paper provides an overview of the CLAM project, which aims at developing a collaborative embedded monitoring and control platform for submarine surveillance by combining cutting edge acoustic vector sensor technology and 1D, 2D, 3D sensor arrays, underwater wireless sensor networks protocol

  10. Cadmium sulfide quantum dots induce oxidative stress and behavioral impairments in the marine clam Scrobicularia plana.

    Science.gov (United States)

    Buffet, Pierre-Emmanuel; Zalouk-Vergnoux, Aurore; Poirier, Laurence; Lopes, Christelle; Risso-de-Faverney, Christine; Guibbolini, Marielle; Gilliland, Douglas; Perrein-Ettajani, Hanane; Valsami-Jones, Eugenia; Mouneyrac, Catherine

    2015-07-01

    Cadmium sulfide (CdS) quantum dots have a number of current applications in electronics and solar cells and significant future potential in medicine. The aim of the present study was to examine the toxic effects of CdS quantum dots on the marine clam Scrobicularia plana exposed for 14 d to these nanomaterials (10 µg Cd L(-1) ) in natural seawater and to compare them with soluble Cd. Measurement of labile Cd released from CdS quantum dots showed that 52% of CdS quantum dots remained in the nanoparticulate form. Clams accumulated the same levels of Cd regardless of the form in which it was delivered (soluble Cd vs CdS quantum dots). However, significant changes in biochemical responses were observed in clams exposed to CdS quantum dots compared with soluble Cd. Increased activities of catalase and glutathione-S-transferase were significantly higher in clams exposed in seawater to Cd as the nanoparticulate versus the soluble form, suggesting a specific nano effect. The behavior of S. plana in sediment showed impairments of foot movements only in the case of exposure to CdS quantum dots. The results show that oxidative stress and behavior biomarkers are sensitive predictors of CdS quantum dots toxicity in S. plana. Such responses, appearing well before changes might occur at the population level, demonstrate the usefulness of this model species and type of biomarker in the assessment of nanoparticle contamination in estuarine ecosystems. © 2015 SETAC.

  11. Effect of mining activities on the clam fisheries and bottom fauna of Goa estuaries

    Digital Repository Service at National Institute of Oceanography (India)

    Parulekar, A.H.; Ansari, Z.A.; Ingole, B.S.

    Comparison of two clam beds and associated benthic fauna, in Mandovi and Cumbarjua canal estuarine system of Goa, India, severely affected by massive inputs of mining rejects, revealed that, in less than 10 years (1972-73 to 1982-83), high biotic...

  12. Allometric relationships in the bioconcentration of heavy metals by the edible tropical clam Gafrarium tumidum

    Energy Technology Data Exchange (ETDEWEB)

    Hedouin, L. [International Atomic Energy Agency-Marine Environment Laboratory, 4 Quai Antoine 1er, MC-98000 Monaco (Monaco); Laboratoire de Biologie et d' Environnement Marins, FRE 2727, La Rochelle University, 22 Av. Michel Crepeau, F-17000 La Rochelle (France); Institut de Recherche pour le Developpement, Centre d' Oceanologie de Marseille, Station Marine d' Endoume, Rue de la Batterie des Lions, F-13007 Marseille (France); Metian, M. [International Atomic Energy Agency-Marine Environment Laboratory, 4 Quai Antoine 1er, MC-98000 Monaco (Monaco); Teyssie, J.-L. [International Atomic Energy Agency-Marine Environment Laboratory, 4 Quai Antoine 1er, MC-98000 Monaco (Monaco); Fowler, S.W. [International Atomic Energy Agency-Marine Environment Laboratory, 4 Quai Antoine 1er, MC-98000 Monaco (Monaco); Fichez, R. [Institut de Recherche pour le Developpement, Centre d' Oceanologie de Marseille, Station Marine d' Endoume, Rue de la Batterie des Lions, F-13007 Marseille (France); Warnau, M. [International Atomic Energy Agency-Marine Environment Laboratory, 4 Quai Antoine 1er, MC-98000 Monaco (Monaco)]. E-mail: m.warnau@iaea.org

    2006-07-31

    Although metal contamination is a problem of major concern in the lagoon of New Caledonia due to intense mining activities conducted on land, very little is known on the metal ecotoxicology of local marine organisms. The clam Gafrarium tumidum was investigated to assess its usefulness as a bioindicator species of metal contamination in this lagoon. More particularly, allometric relationships between metal accumulation and clam size were determined for five common metals in New Caledonian lagoon waters (Cd, Cr, Co, Zn and Ag) using a highly sensitive radiotracer technique. Experimental results showed that allometric relationships were dependent on the element and on the body compartment considered. As a rule, allometric relationships of metal concentration factor were more pronounced in shell than in soft parts. Significant relationships with clam size for Cd, Cr, Co and Zn followed inverse power functions. In contrast, the degree of Ag bioaccumulation was positively correlated with size. In view of the literature on Ag in bivalves, the latter observation suggests the occurrence of a specific detoxification mechanism (sequestration) that would be more efficient in old individuals. Overall, the experimental results indicate that the use of G. tumidum as a bioindicator in monitoring programmes requires selecting individuals of a specific size range in order to obtain comparable information about ambient metal levels. Since the size effect is greatest among smaller individuals, it is recommended to select clams with a shell width greater than 35 mm.

  13. Transobturator tapes are preferable over transvaginal tapes for the management of female stress urinary incontinence: Against

    Directory of Open Access Journals (Sweden)

    Arun Chawla

    2009-01-01

    Full Text Available Midurethral placement of tension-free vaginal tapes with a transvaginal route for stress urinary incontinence achieves higher and better long-term success rates than the transobturator route. Bladder perforations are reported more in transvaginal tape (TVT but incidences of vaginal erosions, extrusion, and groin pain are exceedingly more in TOT groups. There is no clear evidence that transobturator tape (TOT is associated with less post-operative voiding problems than TVT. Major complications such as bowel injuries and significant vascular injuries with TVT are rare. TVT has been found to be superior to TOT and preferable in technically demanding conditions such as prior anti-incontinence operation failures, obese women, and very elevated and scarred lateral cul-de sac. TVT is always preferred in severe grades of stress urinary incontinence and with patients of intrinsic sphincter deficiency (ISD with little or no urethral mobility.

  14. Preliminary Study on Hot Isostatic Pressing Diffusion Bonding for CLAM Steel

    International Nuclear Information System (INIS)

    Chunjing Li; Qunying Huang; Yican Wu

    2006-01-01

    China Low Activation Martensitic (CLAM) steel is being developed in ASIPP (Institute of Plasma Physics, Chinese Academy of Sciences) since three years ago. CLAM is selected as the major candidate structure materials for the FDS series design of fusion reactors and for China liquid metal LiPb Test Blanket Module (TBM) for ITER i.e. DFLL-TBM, which are being carried out in ASIPP. Since the hot isostatic pressing (HIP) bonding technique is one of the main candidate bonding techniques for manufacturing of the first wall of a fusion reactor, research of the HIP technique on CLAM/CLAM is greatly needed. Preliminary HIP diffusion bonding experiments on CLAM steel have been performed. A few machining approaches such as dry-milling, turnery and grounding etc. were used to prepare the sample surfaces and then they were degreased with a mixture of alcohol, ether and acetone in an ultrasonic bath. The samples were joined by HIP diffusion bonding with the compression pressure of 150 MPa and the holding time of 2 ∼ 3 hours under different temperatures between 950 deg. and 1100 deg.. Different seal techniques of the capsules were studied as well. Then appropriate post heat treatment was done. Tests on mechanical properties of the joints such as tensile strength and impact toughness have been performed. The preliminary results show that the tensile properties are roughly the same as those of the base material. The absorbed energy of the joints at present is a little low and further research is needed to increase it. Microstructure of the joints was studied by optical microscope, SEM and TEM. Compositions of the defects on the joining line were analyzed by EDS. Through analysis of the results, optimized parameters for HIP are given. (author)

  15. Gene transcription and biomarker responses in the clam Ruditapes philippinarum after exposure to ibuprofen

    Energy Technology Data Exchange (ETDEWEB)

    Milan, Massimo; Pauletto, Marianna; Patarnello, Tomaso; Bargelloni, Luca [Department of Comparative Biomedicine and Food Science, University of Padova, Viale dell' Universita 16, Legnaro (Padova) (Italy); Marin, Maria Gabriella [Department of Biology, University of Padova, Via Ugo Bassi 58/B, 35131 Padova (Italy); Matozzo, Valerio, E-mail: matozzo@bio.unipd.it [Department of Biology, University of Padova, Via Ugo Bassi 58/B, 35131 Padova (Italy)

    2013-01-15

    Pharmaceuticals are a class of emerging environmental contaminants that continuously enter aquatic environments. Presently, little information is available about the effects of these substances on non-target organisms, such as bivalves. We investigated the effects of ibuprofen (IBU) on the clam Ruditapes philippinarum. Clams were exposed for 1, 3, 5 and 7 days to 0, 100 and 1000 {mu}g IBU/L, and established biomarker responses (haemolymph lysozyme, gill acetylcholinesterase and digestive gland superoxide dismutase activities) as well as digestive gland transcriptome were evaluated. A two-way ANOVA revealed significant effects of both 'IBU concentration' and 'exposure duration' on biomarker responses. Overall, the enzyme activities were generally lower in IBU-exposed clams than in controls. Although limited knowledge of the mollusc transcriptome makes it difficult to interpret the effects of IBU on clams, the gene transcription analysis using DNA microarrays enabled the identification of the putative molecular mode of action of the IBU. The functional analysis of differentially transcribed genes suggests that IBU can interfere with various signalling pathways in clams, such as arachidonic acid metabolism, apoptosis, peroxisomal proliferator-activated receptors, and nuclear factor-kappa B. In addition, several genes involved in the metabolism of xenobiotics (e.g., glutathione S-transferase, sulfotransferase, cytochrome P450) were also found to be significantly affected by IBU exposure. In summary, the integrated approach of gene transcription analysis and biomarker responses facilitated the elucidation of the putative mechanisms of action of IBU in non-target species.

  16. Use of binaural beat tapes for treatment of anxiety: a pilot study of tape preference and outcomes.

    Science.gov (United States)

    Le Scouarnec, R P; Poirier, R M; Owens, J E; Gauthier, J; Taylor, A G; Foresman, P A

    2001-01-01

    Recent studies and anecdotal reports suggest that binaural auditory beats can affect mood, performance on vigilance tasks, and anxiety. To determine whether mildly anxious people would report decreased anxiety after listening daily for 1 month to tapes imbedded with tones that create binaural beats, and whether they would show a definite tape preference among 3 tapes. A 1-group pre-posttest pilot study. Patients' homes. A volunteer sample of 15 mildly anxious patients seen in the Clinique Psyché, Montreal, Quebec. Participants were asked to listen at least 5 times weekly for 4 weeks to 1 or more of 3 music tapes containing tones that produce binaural beats in the electroencephalogram delta/theta frequency range. Participants also were asked to record tape usage, tape preference, and anxiety ratings in a journal before and after listening to the tape or tapes. Anxiety ratings before and after tape listening, pre- and post-study State-Trait Anxiety Inventory scores, and tape preferences documented in daily journals. Listening to the binaural beat tapes resulted in a significant reduction in the anxiety score reported daily in patients' diaries. The number of times participants listened to the tapes in 4 weeks ranged from 10 to 17 (an average of 1.4 to 2.4 times per week) for approximately 30 minutes per session. End-of-study tape preferences indicated that slightly more participants preferred tape B, with its pronounced and extended patterns of binaural beats, over tapes A and C. Changes in pre- and posttest listening State-Trait Anxiety Inventory scores trended toward a reduction of anxiety, but these differences were not statistically significant. Listening to binaural beat tapes in the delta/theta electroencephalogram range may be beneficial in reducing mild anxiety. Future studies should account for music preference among participants and include age as a factor in outcomes, incentives to foster tape listening, and a physiologic measure of anxiety reduction. A

  17. Effects of a paraspinal-lumbar tape application during 7 days on the perceived area of tape contact.

    Science.gov (United States)

    Funk, Stefan; Finke, Roy; Zeh, Stefan; Siebert, Tobias; Puta, Christian

    2017-05-01

    The study aimed to investigate the changes of the perceived area of tape contact during a lumbar tape application that lasted 7 days. Single group, repeated measures study. University research laboratory. Twenty-three healthy collegiate students in sports science. Perceived area of tape contact was collected by preparing a drawing of their individual perceived tape outline into a printed body image. Measurements were obtained immediately after fixation of the tape (day 0), at day 3 and day 7 during application and 5 min after the release of the application (day 7). There was no significant change of the perceived area of tape contact after 3 days of tape application. A significant decrease in the perceived area of tape contact was detected 7 days after application (p area of tape contact of healthy sport students is decreased at 7 days. This effect could not be observed at 3 days. These results provide relevant information for the use of elastic tapes concerning the duration of application in medical therapy. Copyright © 2016 Elsevier Ltd. All rights reserved.

  18. Effects of Kinesio Taping versus McConnell Taping for Patellofemoral Pain Syndrome: A Systematic Review and Meta-Analysis

    Directory of Open Access Journals (Sweden)

    Wen-Dien Chang

    2015-01-01

    Full Text Available Objectives. To conduct a systematic review comparing the effects of Kinesio taping with McConnell taping as a method of conservative management of patients with patellofemoral pain syndrome (PFPS. Methods. MEDLINE, PUBMED, EMBASE, AMED, and the Cochrane Central Register of Control Trials electronic databases were searched through July 2014. Controlled studies evaluating the effects of Kinesio or McConnell taping in PFPS patients were retrieved. Results. Ninety-one articles were selected from the articles that were retrieved from the databases, and 11 articles were included in the analysis. The methods, evaluations, and results of the articles were collected, and the outcomes of patellar tapings were analyzed. Kinesio taping can reduce pain and increase the muscular flexibility of PFPS patients, and McConnell taping also had effect in pain relief and patellar alignment. Meta-analysis showed small effect in pain reduction and motor function improvement and moderate effect in muscle activity change among PFPS patients using Kinesio taping. Conclusions. Kinesio taping technique used for muscles can relieve pain but cannot change patellar alignment, unlike McConnell taping. Both patellar tapings are used differently for PFPS patients and substantially improve muscle activity, motor function, and quality of life.

  19. New polymorphic microsatellite markers derived from hemocyte cDNA library of Manila clam Ruditapes philippinarum challenged by the protozoan parasite Perkinsus olseni

    Science.gov (United States)

    Kang, Hyun-Sil; Hong, Hyun-Ki; Park, Kyung-Il; Cho, Moonjae; Youn, Seok-Hyun; Choi, Kwang-Sik

    2017-03-01

    Manila clam Ruditapes philippinarum is one of the most important benthic animals in the coastal north Pacific region, where clam populations have been mixed genetically through trade and aquaculture activities. Accordingly, identification of the genetically different clam populations has become one of the most important issues to manage interbreeding of the local and introduced clam populations. To identify genetically different populations of clam populations, we developed 11 expressed sequence tag (EST)-microsatellite loci (i.e., simple sequence repeat, SSR) from 1,128 clam hemocyte cDNA clones challenged by the protozoan parasite Perkinsus olseni. Genotype analysis using the markers developed in this study demonstrated that clams from a tidal flat on the west coast contained 6 to 19 alleles per locus, and a population from Jeju Island had 4 to 20 alleles per locus. The expected heterozygosity of the 2 clam populations ranged from 0.472 to 0.919 for clams from the west coast, and 0.494 to 0.919 for clams from Jeju Island, respectively. Among the 11 loci discovered in this study, 7 loci significantly deviated from the Hardy-Weinberg equilibrium after Bonferroni correction. The 5 loci developed in this study also successfully amplified the SSRs of R. variegatus, a clam species taxonomically very close to R. philippinarum, from Hong Kong and Jeju Island. We believe that the 11 novel polymorphic SSR developed in this study can be utilized successfully in Manila clam genetic diversity analysis, as well as in genetic discrimination of different clam populations.

  20. Efeitos do Kinesio Taping no Desporto

    OpenAIRE

    Pereira, Marcelo

    2012-01-01

    Trabalho apresentado à Universidade Fernando Pessoa como parte dos requisitos para obtenção do grau de Licenciado em Fisioterapia O médico japonês, Dr. Kenzo Kase criou, em 1973, o kinesio taping, uma nova aplicação de ligadura adesiva, tendo como objectivo melhorar a função da musculatura, sem limitar os movimentos, reduzir a dor, edema e os espasmos musculares. Parece ter também a capacidade de prevenir lesões no desporto, sendo por isso uma técnica comummente utilizada para este efeito....

  1. StorageTek T10000 Tape Cartridge

    CERN Multimedia

    1985-01-01

    Oracle StorageTek T10000T2 cartridge has total capacity of 5 TB. It is actually manufactured by Fuji Film, uses Barium Ferrite (BaFe) particles technology data store, but is also equipped with RFID chip. There is over 1 km of tape inside of the cartridge with 3584 data tracks and it supports over 25000 load/unload cycles. The archival life is estimated to be around 30 years and uncorrected bit error rate is 10-19. CERN however usually migrates data to newer technologies roughly every 5 years in order to keep the footprint under control.

  2. Information retrieval system based on INIS tapes

    International Nuclear Information System (INIS)

    Pultorak, G.

    1976-01-01

    An information retrieval system based on the INIS computer tapes is described. It includes the three main elements of a computerized information system: a data base on a machine -readable medium, a collection of queries which represent the information needs from the data - base, and a set of programs by which the actual retrieval is done, according to the user's queries. The system is built for the center's computer, a CDC 3600, and its special features characterize, to a certain degree, the structure of the programs. (author)

  3. Design of double tape recorder data acquisition system

    International Nuclear Information System (INIS)

    Guo Tianrui; Du Yifei

    1995-01-01

    In the data acquisition system supported by the microcomputer tape recorder, as the acquisition speed is often limited by the low speed of tape recorder, so a double tape recorder system is designed. In this system, two tape recorders are used in on-line acquisition system simultaneously. One DMA channel used is one designed for soft disk driver, another DMA channel used is one retained for user. By this way, the speed of tape writing could be increased to nearly twice as much. In order to prevent the data confusion, the authors open two data buffers in system and write different mark in each buffer, then write the data block to two tape recorders according to the mark. The system complies with the principle: 'Double write, Double read'

  4. Methods of Measuring Stress Relaxation in Composite Tape Springs

    Science.gov (United States)

    2015-03-26

    10 3. Cure Cycle Recommended for Patz F7 Prepreg . . . . . . . . . . . . . . . . . . . . . 17 4. Typical Stress...unique and dimensionally complex parts. Hand lay-up is the method by which prepreg tape or fibers are laid down and then the matrix is then ‘painted’ on...structure. Hand lay-up using a prepreg tape stands out as the inexpensive choice for the unique low number production of tape springs and should

  5. Influence of particle characteristics and organic matter content on the bioavailability and bioaccumulation of pyrene by clams

    International Nuclear Information System (INIS)

    Verrengia Guerrero, N.R.; Taylor, M.G.; Wider, E.A.; Simkiss, K.

    2003-01-01

    An experimental model with artificial particles and humic acids describes bioavailability of sediment-bound pyrene to clams. - Hydrophobic chemicals are known to associate with sediment particles including those from both suspended particulate matter and bottom deposits. The complex and variable composition of natural particles makes it very difficult therefore, to predict the bioavailability of sediment-bound contaminants. To overcome these problems we have previously devised a test system using artificial particles, with or without humic acids, for use as an experimental model of natural sediments. In the present work we have applied this experimental technique to investigate the bioavailability and bioaccumulation of pyrene by the freshwater fingernail clam Sphaerium corneum. The uptake and accumulation of pyrene in clams exposed to the chemical in the presence of a sample of natural sediment was also investigated. According to the results obtained, particle surface properties and organic matter content are the key factors for assessing the bioavailability and bioaccumulation of pyrene by clams

  6. Bioaccumulation of hydrocarbons derived from terrestrial and anthropogenic sources in the Asian clam, Potamocorbula amurensis, in San Francisco Bay estuary

    Science.gov (United States)

    Pereira, Wilfred E.; Hostettler, Frances D.; Rapp, John B.

    1992-01-01

    An assessment was made in Suisun Bay, California, of the distributions of hydrocarbons in estuarine bed and suspended sediments and in the recently introduced asian clam, Potamocorbula amurensis. Sediments and clams were contaminated with hydrocarbons derived from petrogenic and pyrogenic sources. Distributions of alkanes and of hopane and sterane biomarkers in sediments and clams were similar, indicating that petroleum hydrocarbons associated with sediments are bioavailable to Potamocorbula amurensis. Polycyclic aromatic hydrocarbons in the sediments and clams were derived mainly from combustion sources. Potamocorbula amurensis is therefore a useful bioindicator of hydrocarbon contamination, and may be used as a biomonitor of hydrocarbon pollution in San Francisco Bay.

  7. Impact of High Hydrostatic Pressure on the Shelling Efficacy, Physicochemical Properties, and Microstructure of Fresh Razor Clam (Sinonovacula constricta).

    Science.gov (United States)

    Xuan, Xiao-Ting; Cui, Yan; Lin, Xu-Dong; Yu, Jing-Feng; Liao, Xiao-Jun; Ling, Jian-Gang; Shang, Hai-Tao

    2018-02-01

    The effects of high hydrostatic pressure (HHP) treatments (200, 300, and 400 MPa for 1, 3, 5 and 10 min) on the shelling efficacy (the rate of shelling, the rate of integrity and yield of razor clam meat) and the physicochemical (drip loss, water-holding capacity, pH, conductivity, lipid oxidation, Ca 2+ -ATPase activity, myofibrillar protein content), microbiological (total viable counts) and microstructural properties of fresh razor clam (Sinonovacula constricta) were investigated. HHP treatments significantly (P hydrostatic pressure (HHP) is now well known as a nonthermal processing technology and becoming increasingly acknowledged. However, it has not been widely applied to shell seafood due to its uncertain influence on its quality and shelling property. This study could provide valuable information regarding the shelling efficacy, physicochemical properties, and microstructure of razor clam treated by HHP. And it demonstrated that HHP showed a positive impact on quality of razor clam treated by HHP. © 2018 Institute of Food Technologists®.

  8. Reel-to-reel substrate tape polishing system

    Energy Technology Data Exchange (ETDEWEB)

    Selvamanickam, Venkat; Gardner, Michael T.; Judd, Raymond D.; Weloth, Martin; Qiao, Yunfei

    2005-06-21

    Disclosed is a reel-to-reel single-pass mechanical polishing system (100) suitable for polishing long lengths of metal substrate tape (124) used in the manufacture of high-temperature superconductor (HTS) coated tape, including multiple instantiations of a polishing station (114) in combination with a subsequent rinsing station (116) arranged along the axis of the metal substrate tape (124) that is translating between a payout spool (110a) and a take-up spool (110b). The metal substrate tape obtains a surface smoothness that is suitable for the subsequent deposition of a buffer layer.

  9. Tape-cast sensors and method of making

    Science.gov (United States)

    Mukundan, Rangachary [Santa Fe, NM; Brosha, Eric L [Los Alamos, NM; Garzon, Fernando H [Santa Fe, NM

    2009-08-18

    A method of making electrochemical sensors in which an electrolyte material is cast into a tape. Prefabricated electrodes are then partially embedded between two wet layers of the electrolyte tape to form a green sensor, and the green sensor is then heated to sinter the electrolyte tape around the electrodes. The resulting sensors can be used in applications such as, but not limited to, combustion control, environmental monitoring, and explosive detection. A electrochemical sensor formed by the tape-casting method is also disclosed.

  10. Molten carbonate fuel cell integral matrix tape and bubble barrier

    International Nuclear Information System (INIS)

    Reiser, C.A.; Maricle, D.L.

    1983-01-01

    A molten carbonate fuel cell matrix material is described made up of a matrix tape portion and a bubble barrier portion. The matrix tape portion comprises particles inert to molten carbonate electrolyte, ceramic particles and a polymeric binder, the matrix tape being flexible, pliable and having rubber-like compliance at room temperature. The bubble barrier is a solid material having fine porosity preferably being bonded to the matrix tape. In operation in a fuel cell, the polymer binder burns off leaving the matrix and bubble barrier providing superior sealing, stability and performance properties to the fuel cell stack

  11. Nonlinear Model of Tape Wound Core Transformers

    Directory of Open Access Journals (Sweden)

    A. Vahedi

    2015-03-01

    Full Text Available Recently, tape wound cores due to their excellent magnetic properties, are widely used in different types of transformers. Performance prediction of these transformers needs an accurate model with ability to determine flux distribution within the core and magnetic loss. Spiral structure of tape wound cores affects the flux distribution and always cause complication of analysis. In this paper, a model based on reluctance networks method is presented for analysis of magnetic flux in wound cores. Using this model, distribution of longitudinal and transverse fluxes within the core can be determined. To consider the nonlinearity of the core, a dynamic hysteresis model is included in the presented model. Having flux density in different points of the core, magnetic losses can be calculated. To evaluate the validity of the model, results are compared with 2-D FEM simulations. In addition, a transformer designed for series-resonant converter and simulation results are compared with experimental measurements. Comparisons show accuracy of the model besides simplicity and fast convergence

  12. Award of two contracts for the renting of magnetic tape drives and tape libraries for LHC data storage and the purchase of the associated tape cartridges

    CERN Document Server

    2005-01-01

    This document concerns the award of two contracts for the renting and possible subsequent purchase of magnetic tape drives and tape libraries for LHC data storage. The Finance Committee is invited to agree to the procedure described in section 3 of this document for the evaluation and possible subsequent purchase of tape drives and tape libraries for the storage of data from the LHC experiments. Subject to approval of this procedure, the Finance Committee is further invited to approve the negotiation of a contract for the renting of tape drives and tape libraries for evaluation purposes from IBM, for an amount of 579 707 Swiss francs, and from StorageTek, for an amount of 472 297 Swiss francs, during the period January 2006 â?" March 2007, plus the purchase of the associated tape cartridges for amounts of 202 500 Swiss francs and 284 748 Swiss francs respectively. The Finance Committee will be informed of the results of the evaluation by the end of 2006 and, subject to the outcome, will be invited to approve...

  13. Size-related and seasonal diet of the manila clam (Ruditapes philippinarum), as determined using dual stable isotopes

    Science.gov (United States)

    Suh, Yeon Jee; Shin, Kyung-Hoon

    2013-12-01

    Stable isotope ratios of lab-cultured Manila clams (Ruditapes philippinarum) and those from natural tidal flats of Seonjae Island in Korea were investigated in terms of their dietary uptake patterns in relation to body size and season. The smallest size group of wild Manila clams revealed significantly depleted δ15N based on the results of a one-way ANOVA. There was significant seasonal change in the proportional contribution of food sources, especially in winter, from benthic particulate organic matter (BPOM) to pelagic particulate organic matter (POM). Laboratory-cultured Manila clams showed growth rates of 6.02-37.75 mm/yr, and smaller-sized clams did not fully utilise the microalgal diets that were provided constantly. Instead, they derived most of their energy from detritus or dead microalgae that had settled on the bottom. Bigger clams, however, exhibited well-balanced source contributions, converting the microalgal diets into biomass. This demonstrates intra-specific differences in the growth rates and preferred diet uptakes of Manila clams, even under similar environmental conditions.

  14. Tropical troposphere to stratosphere transport of carbon monoxide and long-lived trace species in the Chemical Lagrangian Model of the Stratosphere (CLaMS

    Directory of Open Access Journals (Sweden)

    R. Pommrich

    2014-12-01

    Full Text Available Variations in the mixing ratio of trace gases of tropospheric origin entering the stratosphere in the tropics are of interest for assessing both troposphere to stratosphere transport fluxes in the tropics and the impact of these transport fluxes on the composition of the tropical lower stratosphere. Anomaly patterns of carbon monoxide (CO and long-lived tracers in the lower tropical stratosphere allow conclusions about the rate and the variability of tropical upwelling to be drawn. Here, we present a simplified chemistry scheme for the Chemical Lagrangian Model of the Stratosphere (CLaMS for the simulation, at comparatively low numerical cost, of CO, ozone, and long-lived trace substances (CH4, N2O, CCl3F (CFC-11, CCl2F2 (CFC-12, and CO2 in the lower tropical stratosphere. For the long-lived trace substances, the boundary conditions at the surface are prescribed based on ground-based measurements in the lowest model level. The boundary condition for CO in the lower troposphere (below about 4 km is deduced from MOPITT measurements. Due to the lack of a specific representation of mixing and convective uplift in the troposphere in this model version, enhanced CO values, in particular those resulting from convective outflow are underestimated. However, in the tropical tropopause layer and the lower tropical stratosphere, there is relatively good agreement of simulated CO with in situ measurements (with the exception of the TROCCINOX campaign, where CO in the simulation is biased low ≈10–15 ppbv. Further, the model results (and therefore also the ERA-Interim winds, on which the transport in the model is based are of sufficient quality to describe large scale anomaly patterns of CO in the lower stratosphere. In particular, the zonally averaged tropical CO anomaly patterns (the so called "tape recorder" patterns simulated by this model version of CLaMS are in good agreement with observations, although the simulations show a too rapid upwelling

  15. Effects of clam size, food type, sediment characteristic, and seawater carbonate chemistry on grazing capacity of Venus clam Cyclina sinensis (Gmelin, 1791)

    Science.gov (United States)

    Lin, Tingting; Zhou, Kai; Liu, Xin; Lai, Qifang; Zhang, Dong; Shi, Liyan

    2017-09-01

    Aquaculture in saline-alkaline water has a major problem: microalgal blooming causes the pH of water to increase dramatically, thereby causing damage to the reared organisms. To solve this problem, we set out to find a candidate filter-feeding bivalve species suitable for saline-alkaline water to graze on microalgae and to control the pH. In the current study, we investigated the effect of carbonate alkalinity (CA, 2.5, 10.0, and 20.0 meq/L) and pH (8.0, 8.5, and 9.0) on the grazing capacity (GC) of the clam Cyclina sinensis. Additionally, the effect of clam size (small, medium, and large) and microalgae species ( Nannochloropsis oculata, Chaetoceros müelleri, and Isochrysis galbana), and the effect of bottom sediment characteristic (mud, sandy mud, and muddy sand) and thickness (3 and 6 cm) were analyzed as well. The results show that the GC on I. galbana was the highest and small size had the maximum GC/ W ( W: wet weight including body and shells). No significant differences were observed between sediment type and thickness. Regarding CA and pH, a significant decrease in GC by the pH or by their interaction was found. The GC of C. sinensis was not greatly reduced in the treatments of pH≤8.5 and CA≤20.0, and also not affected by bottom sediment type, indicating that this clam is capable to manage microalgal concentrations and might be a candidate species for pH reduction in saline-alkaline water ponds.

  16. Creep deformation and rupture behavior of CLAM steel at 823 K and 873 K

    Science.gov (United States)

    Zhong, Boyu; Huang, Bo; Li, Chunjing; Liu, Shaojun; Xu, Gang; Zhao, Yanyun; Huang, Qunying

    2014-12-01

    China Low Activation Martensitic (CLAM) steel is selected as the candidate structural material in Fusion Design Study (FDS) series fusion reactor conceptual designs. The creep property of CLAM steel has been studied in this paper. Creep tests have been carried out at 823 K and 873 K over a stress range of 150-230 MPa. The creep curves showed three creep regimes, primary creep, steady-state creep and tertiary creep. The relationship between minimum creep rate (ε˙min) and the applied stress (σ) could be described by Norton power law, and the stress exponent n was decreased with the increase of the creep temperature. The creep mechanism was analyzed with the fractographes of the rupture specimens which were examined by scanning electron microscopy (SEM). The coarsening of precipitates observed with transmission electron microscope (TEM) indicated the microstructural degradation after creep test.

  17. Heavy metal concentrations in the razor clams (Solen spp.) from Muara Tebas, Sarawak

    International Nuclear Information System (INIS)

    Devagi Kanakaraju; Connie Jios; Shabdin Mohd Long

    2008-01-01

    The razor clams (Solen spp) or locally known as ambal in Sarawak collected from Muara Tebas were studied for their heavy metals contents in tissues and shells. Sediment samples were also tested for their metal contents. Concentrations of Pb, Fe, Zn, Cu, Cd and Mn were determined by using Flame Atomic Absorption Spectrophotometer (FAAS). Tissues of razor clams showed highest concentrations of Fe and Zn, while shells accumulated highest concentrations of Pb and Mn. The lowest metal concentrations found were Cu and Cd. In general, the levels of metals in ambal were within the permissible limit recommended by international standard, the Food and Agricultural Organization (FAO). However, the study revealed that the sediments at Muara Tebas fall under the category of slightly polluted (for Pb) when compared to the guidelines suggested by United States Environment Protection Agency (USEPA). (author)

  18. Creep deformation and rupture behavior of CLAM steel at 823 K and 873 K

    International Nuclear Information System (INIS)

    Zhong, Boyu; Huang, Bo; Li, Chunjing; Liu, Shaojun; Xu, Gang; Zhao, Yanyun; Huang, Qunying

    2014-01-01

    China Low Activation Martensitic (CLAM) steel is selected as the candidate structural material in Fusion Design Study (FDS) series fusion reactor conceptual designs. The creep property of CLAM steel has been studied in this paper. Creep tests have been carried out at 823 K and 873 K over a stress range of 150–230 MPa. The creep curves showed three creep regimes, primary creep, steady-state creep and tertiary creep. The relationship between minimum creep rate (ε-dot min ) and the applied stress (σ) could be described by Norton power law, and the stress exponent n was decreased with the increase of the creep temperature. The creep mechanism was analyzed with the fractographes of the rupture specimens which were examined by scanning electron microscopy (SEM). The coarsening of precipitates observed with transmission electron microscope (TEM) indicated the microstructural degradation after creep test

  19. Sputtered thin films for high density tape recording

    NARCIS (Netherlands)

    Nguyen, L.T.

    This thesis describes the investigation of sputtered thin film media for high density tape recording. As discussed in Chapter 1, to meet the tremendous demand of data storage, the density of recording tape has to be increased continuously. For further increasing the bit density the key factors are:

  20. Enhancement of heat transfer using varying width twisted tape inserts

    African Journals Online (AJOL)

    user

    enhancement of heat transfer with twisted tape inserts as compared to plain ... studies for heat transfer and pressure drop of laminar flow in horizontal tubes ... flow in rectangular and square plain ducts and ducts with twisted-tape inserts .... presence of the insert in the pipe causes resistance to flow and increases turbulence.

  1. Recovery of recordings from heat damaged magnetic tapes

    Science.gov (United States)

    Melugin, J. F.; Obrien, D. E., III

    1973-01-01

    Damaged tapes can now be repaired at home as long as damage does not extend to layer-to-layer adhesion within tape roll. Splice repaired section into good roll or cassette for copying. Every effort should be made to complete copying on first run, because fidelity in repaired section deteriorates with each repetition.

  2. Ring shaped laser for tape winding of an endless tube

    NARCIS (Netherlands)

    Leonardus, Lucky

    2012-01-01

    AFPT is a start-up company that provides laser-assisted technology for the production of a pressurized component such as tube, pressure vessel, etc made from or strengthened by fiber reinforced plastic (FRP) tape. The tape is laid precisely by a machine head (connected to a robot), melted with a

  3. StorageTek RedWood SD-3 tape drive

    CERN Multimedia

    1995-01-01

    A helical scan recording drive, with a high-speed rotating head sweeping across the tape every few micrometers. Based on a professional video recording system, modified to be suitable for digital data recording. These are commonly used with large computer systems, typically in conjunction with a robotic tape library.

  4. Multilayer tape cast SOFC – Effect of anode sintering temperature

    DEFF Research Database (Denmark)

    Hauch, Anne; Birkl, Christoph; Brodersen, Karen

    2012-01-01

    Multilayer tape casting (MTC) is considered a promising, cost-efficient, up-scalable shaping process for production of planar anode supported solid oxide fuel cells (SOFC). Multilayer tape casting of the three layers comprising the half cell (anode support/active anode/electrolyte) can potentially...

  5. Increasing the efficiency of tape-based storage backends

    International Nuclear Information System (INIS)

    Bessone, Nicola; Cancio, German; Murray, Steve; Taurelli, Giulia

    2010-01-01

    HSM systems such as the CERN's Advanced STORage manager (CASTOR) [1] are responsible for storing Petabytes of data which is first cached on disk and then persistently stored on tape media. The contents of these tapes are regularly repacked from older, lower-density media to new-generation, higher-density media in order to free up physical space and ensure long term data integrity and availability. With the evolution of price decay and higher capacity of disk (and flash memory) based storage, our future vision for tape usage is to move away from serving on demand, random, per-file access to non-disk cached files, and to move towards loosely coupled, efficient bulk data transfers where large-volume data sets are stored and retrieved in aggregations, fully exploiting the stream-based nature of tape media. Mechanisms for grouped migration policies and priorities have been implemented, and an innovative tape format optimized for data aggregations is being developed. This new tape format will also allow for increasing the performance of repacking data from old to newer generation tape media with substantially reduced hardware costs. In this paper, we will describe the improvements for migration policies and priorities, as well as the proposed tape format and the changes which will be applied to the architecture of the CASTOR mass storage system.

  6. Study on niobium carbide dispersed superconducting tapes

    Energy Technology Data Exchange (ETDEWEB)

    Wada, H; Tachikawa, K [National Research Inst. for Metals, Tokyo (Japan); Oh' asa, M [Science Univ. of Tokyo (Japan)

    1977-11-01

    Niobium carbide (NbC) dispersed superconducting tapes have been fabricated by two metallurgical processes. In the first process, Ni-Nb-C alloys are directly arc melted and hot worked in air and the NbC phase is distributed in the form of fine discrete particles. In the second process, Ni-Nb and Ni-Nb-Cu alloys are arc melted, hot worked and subjected to solid-state carburization. NbC then precipitates along the grain boundaries, forming a network. The highest superconducting transition temperature attained is about 11 K. Taken together with the lattice parameter measurement, this indicates that NbC with a nearly perfect NaCl structure is formed in both processes. Measured values of the upper critical field, the critical current density and the volume fraction of the NbC phase are also discussed.

  7. Kinesio taping in patients with lateral epicondylitis.

    Science.gov (United States)

    Dilek, Banu; Batmaz, Ibrahim; Sarıyıldız, Mustafa Akif; Sahin, Ebru; Ilter, Leman; Gulbahar, Selmin; Cevik, Remzi; Nas, Kemal

    2016-11-21

    Lateral epicondylitis (LE) is a painful condition that affects the tendinous tissue of the lateral epicondyle of the humerus and leads to loss of function of the affected limb. Therefore it can have a major impact on the patient's social and personal life. Many treatments are recommended for lateral epicondylitis; unfortunately the evidence is limited. The aim of study was to investigate the effect of kinesio taping (KT) on pain, grip strength and function in patients LE. Thirty-one (23 females, 8 males) patients with LE were included. KT was applied twice a week for 2 weeks. Pain at rest, activity of daily living (ADL), night and palpation on lateral epicondyle was evaluated with the visual analog scale (VAS 0-10 cm), and the grip strength was measured with a hand held dynamometer. The stage of the disease was evaluated by the Nirschl score and the functional status was assessed with Patient-Rated Forearm Evaluation Questionnaire (PRTEQ) score. These parameters were evaluated before, at 2 weeks and 6 weeks after treatment. Patients' satisfaction was also recorded on a Likert scale after treatment at 2 weeks and 6 weeks. The average age of the patients was 43.58 ± 9.02. The dominant limb was affected in 64.5% (20) of the patients. After the application of KT on lateral epicondyle, there was a significant improvement in all parameters in terms of pain, Nirschl score, hand grip strength, patient satisfaction, and PRTEQ scores at 2 and 6 weeks. Kinesio taping can be an effective treatment method in LE. This application improves pain, grip strength and functional status of the patients with LE.

  8. Acute and chronic exposure in mussel (aulacomya ater) and clam (semelle solida) with Cs137

    International Nuclear Information System (INIS)

    Bringas, J.E.

    1996-01-01

    Two of the most common Peruvian benthonic molluscs, have been shown to be effective concentrators of Cesium-137 and have also proven useful as indicators of that radionuclide in their natural environment, according with results in this paper. However the clam is a better indicator, when determining environmental acute release of Cesium-137 due to reactor accidents, nuclear tests, accidents in nuclear ships, submarines and radioactive material transport, and the mussel for a continuous monitoring of environmental radio contaminant levels. (author). 11 refs

  9. Effect of weld spacing on microstructure and mechanical properties of CLAM electron beam welding joints

    Energy Technology Data Exchange (ETDEWEB)

    Zhai, Yutao; Huang, Bo, E-mail: aufa0007@163.com; Zhang, Junyu; Zhang, Baoren; Liu, Shaojun; Huang, Qunying

    2016-11-15

    Highlights: • The welded joints of CLAM steel with different weld spacings have been fabricated with electron beam welding, and a simplified model of CLAM sheet was proposed. • The microstructure and mechanical properties such as microhardness, impact and tensile were investigated at different welding spacing for both conditions of as-welded and post weld heat treatment (PWHT). • The effect of the welding thermal cycle was significantly when the weld spacings were smaller than 4 mm. • When the weld spacing was small enough, the original microstructures would be fragmented with the high heat input. - Abstract: China low activation martensitic (CLAM) steel has been chosen as the primary structural material in the designs of dual function lithium-lead (DFLL) blanket for fusion reactors, China helium cooled ceramic breeder (HCCB) test blanket module (TBM) for ITER and China fusion engineering test reactor (CFETR) blanket. The cooling components of the blankets are designed with high density cooling channels (HDCCs) to remove the high nuclear thermal effectively. Hence, the welding spacing among the channels are small. In this paper, the welded joints of CLAM steel with different weld spacings have been fabricated with electron beam welding (EBW). The weld spacing was designed to be 2 mm, 3 mm, 4 mm, 6 mm and 8 mm. The microstructure and mechanical properties such as microhardness, impact and tensile were investigated at different welding spacing for both conditions of as-welded and post weld heat treatment (PWHT). The PWHT is tempering at 740 °C for 120 min. The results showed that the grain size in the heat affected zone (HAZ) increased with the increasing weld spacing, and the joint with small weld spacing had a better performance after PWHT. This work would give useful guidance to improve the preparation of the cooling components of blanket.

  10. Ecotoxicological Effects of Chemical Contaminants Adsorbed to Microplastics in the Clam Scrobicularia plana

    Directory of Open Access Journals (Sweden)

    Sarit O'Donovan

    2018-04-01

    Full Text Available Although microplastics (MPs are distributed globally in the marine environment, a great deal of unknowns relating to their ecotoxicological effects on the marine biota remains. Due to their lipophilic nature, microplastics have the potential to adsorb persistent organic pollutants present in contaminated regions, which may increase their detrimental impact once assimilated by organisms. This study investigates the ecotoxicological effects of exposure to low-density polyethylene (LDPE microplastics (11–13 μm, with and without adsorbed contaminants (benzo[a]pyrene—BaP and perfluorooctane sulfonic acid—PFOS, in the peppery furrow shell clam, Scrobicularia plana. Environmentally relevant concentrations of contaminants (BaP−16.87 ± 0.22 μg g−1 and PFOS−70.22 ± 12.41 μg g−1 were adsorbed to microplastics to evaluate the potential role of plastic particles as a source of chemical contamination once ingested. S. plana were exposed to microplastics, at a concentration of 1 mg L−1, in a water-sediment exposure setup for 14 days. Clams were sampled at the beginning of the experiment (day 0 and after 3, 7, and 14 days. BaP accumulation, in whole clam tissues, was analyzed. A multi-biomarker assessment was conducted in the gills, digestive gland, and haemolymph of clams to clarify the effects of exposure. This included the quantification of antioxidant (superoxide dismutase, catalase, glutathione peroxidase and biotransformation (glutathione-S-transferases enzyme activities, oxidative damage (lipid peroxidation levels, genotoxicity (single and double strand DNA breaks, and neurotoxicity (acetylcholinesterase activity. Results suggest a potential mechanical injury of gills caused by ingestion of microplastics that may also affect the analyzed biomarkers. The digestive gland seems less affected by mechanical damage caused by virgin microplastic exposure, with the MPs-adsorbed BaP and PFOS exerting a negative influence over the assessed

  11. Microbiota and environmental stress: how pollution affects microbial communities in Manila clams.

    Science.gov (United States)

    Milan, M; Carraro, L; Fariselli, P; Martino, M E; Cavalieri, D; Vitali, F; Boffo, L; Patarnello, T; Bargelloni, L; Cardazzo, B

    2018-01-01

    Given the crucial role of microbiota in host development, health, and environmental interactions, genomic analyses focusing on host-microbiota interactions should certainly be considered in the investigation of the adaptive mechanisms to environmental stress. Recently, several studies suggested that microbiota associated to digestive tract is a key, although still not fully understood, player that must be considered to assess the toxicity of environmental contaminants. Bacteria-dependent metabolism of xenobiotics may indeed modulate the host toxicity. Conversely, environmental variables (including pollution) may alter the microbial community and/or its metabolic activity leading to host physiological alterations that may contribute to their toxicity. Here, 16s rRNA gene amplicon sequencing has been applied to characterize the hepatopancreas microbiota composition of the Manila clam, Ruditapes philippinarum. The animals were collected in the Venice lagoon area, which is subject to different anthropogenic pressures, mainly represented by the industrial activities of Porto Marghera (PM). Seasonal and geographic differences in clam microbiotas were explored and linked to host response to chemical stress identified in a previous study at the transcriptome level, establishing potential interactions among hosts, microbes, and environmental parameters. The obtained results showed the recurrent presence of putatively detoxifying bacterial taxa in PM clams during winter and over-representation of several metabolic pathways involved in xenobiotic degradation, which suggested the potential for host-microbial synergistic detoxifying actions. Strong interaction between seasonal and chemically-induced responses was also observed, which partially obscured such potentially synergistic actions. Seasonal variables and exposure to toxicants were therefore shown to interact and substantially affect clam microbiota, which appeared to mirror host response to environmental variation. It

  12. Composting clam processing wastes in a laboratory- and pilot-scale in-vessel system.

    Science.gov (United States)

    Hu, Zhenhu; Lane, Robert; Wen, Zhiyou

    2009-01-01

    Waste materials from the clam processing industry (offal, shells) have several special characteristics such as a high salinity level, a high nitrogen content, and a low C/N ratio. The traditional disposal of clam waste through landfilling is facing the challenges of limited land available, increasing tipping fees, and strict environmental and regulatory scrutiny. The aim of this work is to investigate the performance of in-vessel composting as an alternative for landfill application of these materials. Experiments were performed in both laboratory-scale (5L) and pilot-scale (120L) reactors, with woodchips as the bulking agent. In the laboratory-scale composting test, the clam waste and woodchips were mixed in ratios from 1:0.5 to 1:3 (w/w, wet weight). The high ratios resulted in a better temperature performance, a higher electrical conductivity, and a higher ash content than the low-ratio composting. The C/N ratio of the composts was in the range of 9:1-18:1. In the pilot-scale composting test, a 1:1 ratio of clam waste to woodchips was used. The temperature profile during the composting process met the US Environmental Protection Agency sanitary requirement. The final cured compost had a C/N ratio of 14.6, with an ash content of 167.0+/-14.1g/kg dry matter. In addition to the major nutrients (carbon, nitrogen, calcium, magnesium, phosphorus, potassium, sulfur, and sodium), the compost also contained trace amounts of zinc, manganese, copper, and boron, indicating that the material can be used as a good resource for plant nutrients.

  13. Clam-Gallasův palác - emblematická architektura?

    Czech Academy of Sciences Publication Activity Database

    Konečný, Lubomír

    2009-01-01

    Roč. 28, - (2009), s. 91-98 ISSN 0231-7443. [Život pražských paláců. Praha, 09.10.2007-11.10.2007] Institutional research plan: CEZ:AV0Z80330511 Keywords : Clam-Gallas Palace * Johann Bernhard Fischer von Erlach * architecture * emblem s * imprints Subject RIV: AL - Art, Architecture, Cultural Heritage

  14. Intersex related gene expression profiles in clams Scrobicularia plana: Molecular markers and environmental application

    International Nuclear Information System (INIS)

    Ciocan, Corina M.; Cubero-Leon, Elena; Langston, William J.; Pope, Nick; Cornelius, Keith; Hill, E.M.; Alvarez-Munoz, Diana; Indiveri, Paolo; Lerebours, Adelaide; Minier, Christophe; Rotchell, Jeanette M.

    2015-01-01

    Highlights: • Expression of intersex-related genes was analysed in clam gonads sampled from the Channel. • Genes were differentially expressed at sites with varying levels of intersex and contaminants. • Correlations between gene expressions, key contaminants and sampling sites were identified. • No single gene expression studied correlated with intersex incidence. - Abstract: Intersex, the appearance of female characteristics in male gonads, has been identified in several aquatic species. It is a widespread phenomenon in populations of the bivalve, Scrobicularia plana, from the southwest coast of the U.K. Genes previously identified as differentially expressed (ferritin, testicular haploid expressed gene, THEG, proliferating cell nuclear antigen, PCNA; receptor activated protein kinase C, RACK; cytochrome B, CYB; and cytochrome c oxidase 1, COX1) in intersex clams relative to normal male clams, were selected for characterisation and an environmental survey of the Channel region. Transcripts were significantly differentially expressed at sites with varying intersex incidence and contaminant burdens. Significant correlations between specific gene expressions, key contaminants and sampling locations have been identified, though no single gene was associated with intersex incidence. The results highlight the difficulty in understanding the intersex phenomenon in molluscs where there is still a lack of knowledge on the control of normal reproduction

  15. Fracture toughness of China low activation martensitic (CLAM) steel at room temperature

    Energy Technology Data Exchange (ETDEWEB)

    Li, Kunfeng [University of Science and Technology of China, Hefei, Anhui 230027 (China); Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Liu, Shaojun, E-mail: shaojun.liu@fds.org.cn [Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Huang, Qunying [University of Science and Technology of China, Hefei, Anhui 230027 (China); Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Xu, Gang; Jiang, Siben [Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China)

    2014-04-15

    Highlights: • The fracture toughness of CLAM steel at room temperature is 417.9 kJ/m{sup 2} measured by unloading compliance method according to the ASTM E1820-11. • The fracture toughness of CLAM steel at room temperature can be calculated on the basis of the fractal dimensions measured under plane strain conditions. The calculated result and relative error for this experiment are 454.6 kJ/m{sup 2} and 8.78% respectively. • The calculation method could be used to estimate the fracture toughness of materials with analysis of the fracture surface. - Abstract: The fracture toughness (J{sub IC}) of China low activation martensitic (CLAM) steel was tested at room temperature through the compact tension specimen, the result is 417.9 kJ/m{sup 2}, which is similar to the JLF-1 at same experimental conditions. The microstructural observation of the fracture surface shows that the fracture mode is a typical ductile fracture. Meanwhile, the fracture toughness is also calculated on the basis of the fractal dimension and the calculated result is 454.6 kJ/m{sup 2}, which is consistent well with the experimental result. This method could be used to estimate the fracture toughness of materials by analyzing of the fracture surface.

  16. Effect of Tantalum content on the low cycle fatigue properties of CLAM steel at 823 K

    Energy Technology Data Exchange (ETDEWEB)

    Zhai, Xiangwei [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); University of Science and Technology of China, Hefei, Anhui, 230027 (China); Liu, Shaojun, E-mail: shaojun.liu@fds.org.cn [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); Zhao, Yanyun; Wang, Kun [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China)

    2017-01-15

    Highlights: • The fatigue life initially decreased and then increased as the Ta content was increased from 0.027 wt% to 0.18 wt%. • The softening rate had declined with Ta content increased and the reduced softening rate was attributed to the increased number of Ta-rich MX particles. • The grain size and M{sub 23}C{sub 6} were closely associated with the Ta content. • The crack distribution was quite sensitive to the Ta content. - Abstract: The effect of tantalum (Ta) content on the low cycle fatigue (LCF) properties of CLAM steel at 823 K was investigated in this paper. Low cycle fatigue tests were carried out on four ingots of CLAM steel with Ta contents of 0.027 wt%, 0.078 wt%, 0.15 wt% and 0.18 wt%, respectively. The results showed that the fatigue life and softening behavior of CLAM steel were influenced by Ta content. The fatigue life initially decreased and then increased as the Ta content was increased from 0.027 wt% to 0.18 wt%. The softening rate had declined with Ta content increased and the reduced softening rate was attributed to the increased number of Ta-rich MX particles.

  17. Changes in fatty acid composition in the giant clam Tridacna maxima in response to thermal stress.

    Science.gov (United States)

    Dubousquet, Vaimiti; Gros, Emmanuelle; Berteaux-Lecellier, Véronique; Viguier, Bruno; Raharivelomanana, Phila; Bertrand, Cédric; Lecellier, Gaël J

    2016-10-15

    Temperature can modify membrane fluidity and thus affects cellular functions and physiological activities. This study examines lipid remodelling in the marine symbiotic organism, Tridacna maxima, during a time series of induced thermal stress, with an emphasis on the morphology of their symbiont Symbiodinium First, we show that the French Polynesian giant clams harbour an important proportion of saturated fatty acids (SFA), which reflects their tropical location. Second, in contrast to most marine organisms, the total lipid content in giant clams remained constant under stress, though some changes in their composition were shown. Third, the stress-induced changes in fatty acid (FA) diversity were accompanied by an upregulation of genes involved in lipids and ROS pathways. Finally, our microscopic analysis revealed that for the giant clam's symbiont, Symbiodinium, thermal stress led to two sequential cell death processes. Our data suggests that the degradation of Symbiodinium cells could provide an additional source of energy to T maxima in response to heat stress. © 2016. Published by The Company of Biologists Ltd.

  18. Triangular gold nanoparticles modify shell characteristics and increase antioxidant enzyme activities in the clam Ruditapes decussatus.

    Science.gov (United States)

    Abdelhafidh, Khazri; Badreddine, Sellami; Mezni, Amine; Mouhamed, Dellali; Wiem, Saidani; Imen, Bouzidi; David, Sheehan; Mahmoudi, Ezzeddine; Hamouda, Beyrem

    2018-04-19

    Nanoparticles may cause adverse environmental effects but there is limited information on their interactions with marine organisms. Our aim was to examine the effects of triangular gold nanoparticles (Tr-Au NPs) on the clam, Ruditapes decussatus. Clams were exposed to Tr-Au1 = 5 µg/L and Tr-Au2 = 10 µg/L for 2 and 7 days. Effects on shell structure were investigated. Superoxide dismutase (SOD), catalase (CAT), glutathione transferase (GST) activities, protein carbonyl levels and malondialdehyde content were used to assess biochemical status. Transmission electron microscopy (TEM) and electron dispersive X-ray microanalysis (EDX) showed that Tr-Au NPs modified shell structure and morphology. Tr-Au NPs size increased forming aggregate particles. Tr-Au NPs increased SOD, CAT and GST activities in gill and digestive gland in a concentration- and time-dependent manner indicating defence against oxidative stress. Enhanced lipid peroxidation and protein carbonyl levels confirmed oxidative stress. Tr-Au NPs cause oxidative stress and affect shell structure of clams. These findings may have relevance to other marine species.

  19. Assessment of relationship between rainfall and Escherichia coli in clams (Chamelea gallina using the Bayes Factor

    Directory of Open Access Journals (Sweden)

    Cesare Ciccarelli

    2017-08-01

    Full Text Available Consumption of bivalve shellfish harvested from water contaminated with sewage pollution presents a risk of human infections and targeting control measures require a good understanding of environmental factors influencing the transport and the fate of faecal contaminants within the hydrological catchments. Although there has been extensive development of regression models, the point of this paper, focused on the relationship between rainfall events and concentrations of Escherichia coli monitored in clams, was the use of a Bayesian approach, by the Bayes Factor. The study was conducted on clams harvested from the south coast of Marche Region (Italy, a coastal area impacted by continuous treated effluents, intermittent rainfalldependent untreated sewage spillage - as a consequence of stormwater overflowing - and rivers with an ephemeral flow regime. The work compared the different interpretation criteria of Bayes Factor, confirmed that E. coli concentrations in clams from the studied area varied in correlation with rainfall events, and demonstrated the effectiveness of Bayes Factor in the assessment of shellfish quality in coastal marine waters. However, it suggested that further investigations would be warranted to determine which environmental factors provide the better basis for accurate and timely predictions. Furthermore the gathered data could be useful, to the local authorities of Marche Region, in the definition of flexible monitoring programmes, taking into account the atmospheric events that could affect the correct functioning of sewage managing systems and the flow of tributary rivers.

  20. Modeling habitat suitability of the invasive clam Corbicula fluminea in a Neotropical shallow lagoon, southern Brazil

    Directory of Open Access Journals (Sweden)

    T. C. L. Silveira

    Full Text Available Abstract This study aimed to model the habitat suitability for an invasive clam Corbicula fluminea in a coastal shallow lagoon in the southern Neotropical region (–30.22, –50.55. The lagoon (19km2, maximum deep 2.5m was sampled with an Ekman dredge in an orthogonal matrix comprising 84 points. At each sampling point, were obtained environmental descriptors as depth, organic matter content (OMC, average granulometry (Avgran, and the percentage of sand (Pcsand. Prediction performance of Generalized Linear Models (GLM, Generalized Additive Models (GAM and Boosted Regression Tree (BRT were compared. Also, niche overlapping with other native clam species (Castalia martensi, Neocorbicula limosa and Anodontites trapesialis was examined. A BRT model with 1400 trees was selected as the best model, with cross-validated correlation of 0.82. The relative contributions of predictors were Pcsand-42.6%, OMC-35.8%, Avgran-10.9% and Depth-10.8%. Were identified that C. fluminea occur mainly in sandy sediments with few organic matter, in shallow areas nor by the shore. The PCA showed a wide niche overlap with the native clam species C. martensi, N. limosa and A. trapesialis.

  1. Histopathology and stress biomarkers in the clam Venerupis philippinarum from the Venice Lagoon (Italy).

    Science.gov (United States)

    Boscolo Papo, Michele; Bertotto, Daniela; Quaglio, Francesco; Vascellari, Marta; Pascoli, Francesco; Negrato, Elena; Binato, Giovanni; Radaelli, Giuseppe

    2014-07-01

    The aim of this study was to evaluate the histomorphology and the stress response in the bivalve Venerupis philippinarum sampled in four differently polluted sites of the Venice Lagoon (Palude del Monte, Marghera, Ca' Roman and Val di Brenta). This species is often used as bioindicator of environmental pollution since it can bioaccumulate a large variety of pollutants because of its filter feeding. Chemical analyses for heavy metals (Cd, Cu, Hg and Pb) and polycyclic aromatic hydrocarbons (PAHs) were performed on whole soft tissues of V. philippinarum. The histological evaluation of clams revealed the presence of Perkinsus sp. infection in animals from all sites, although a very high prevalence of parasites was evidenced in clams from Ca' Roman. Perkinsus sp. were systemically distributed in the mantle, in the intestine and digestive gland, in gonads and gills. The trophozoites of Perkinsus sp. were found isolated or in cluster surrounded by a heavy hemocitical response. Haemocytes always exhibited an immunopositivity to cytochrome P4501A (CYP1A), heat shock protein 70 (HSP70), 4-hydroxy-2-nonenal (HNE) and nitrotyrosine (NT) antibodies. The digestive gland of animals from Palude del Monte showed the highest malondialdehyde (MDA) concentration, whereas clams from Ca' Roman exhibited the highest quantity of metallothioneins. Copyright © 2014 Elsevier Ltd. All rights reserved.

  2. Microstructure evolution of the oxide dispersion strengthened CLAM steel during mechanical alloying process

    Energy Technology Data Exchange (ETDEWEB)

    Song, Liangliang [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Science, Hefei, Anhui, 230031 (China); University of Science and Technology of China, Hefei, Anhui, 230031 (China); Liu, Shaojun, E-mail: shaojun.liu@fds.org.cn [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Science, Hefei, Anhui, 230031 (China); Mao, Xiaodong [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Science, Hefei, Anhui, 230031 (China)

    2016-11-15

    Highlights: • A nano-sized oxides dispersed ODS-CLAM steel was obtained by MA and HIP. • A minimum saturated grain size of down to 30 nm was achieved by varying the milling time from 0 to 100 h. • Solution of W in the MA powder could be significantly improved by increasing MA rotation speed. - Abstracts: Oxide dispersion strengthened Ferritic/Martensitic steel is considered as one of the most potential structural material for future fusion reactor, owing to its high mechanical properties and good irradiation resistance. The oxide dispersion strengthened China Low Activation Martensitic (ODS-CLAM) steel was fabricated by mechanical alloying (MA) and hot isostatic pressing (HIP). The microstructural evolutions during the process of ball milling and subsequent consolidation were investigated by SEM, XRD and TEM. The results showed that increasing the milling time during the first 36 h milling could effectively decrease the grain size to a value of around 30 nm, over which grain sized remained nearly constant. Increasing the rotation speed promoted the solution of tungsten (W) element obviously and decreased the grain size to a certain degree. Observation on the consolidated and further heat-treated ODS-CLAM steel samples indicated that a martensite microstructure with a high density of nano-particles was achieved.

  3. Irradiation control of pathogenic bacteria and their growth during storage in short neckde clam

    International Nuclear Information System (INIS)

    Ju Hua; Wang Feng; Ha Yiming; Liu Shuliang

    2009-01-01

    The growth of pathogenic bacteria during storage and their D 10 values by irradiation in short necked clam were evaluated. The results showed that the D 10 values of the total bacteria count, E. coli, Vibrio parahaemolyticus in short necked clam at 0 degree C ∼ 4 degree C condition were 0.70, 0.56, 0.20kGy, respectively. The results showed that total bacteria count in vacuum packaged short necked clam sample was 4.46 log (CFU/g) after 3kGy 60 Co γ-irradiation and 28 days stored under 0 degree C ∼ 4 degree C, which could meet the requirement of related aquatic product standards, the E. coli and Vibrio parahaemolyticus would not detected after 0.4kGy irradiation and 7 days storage at 0 degree C ∼ 4 degree C. Therefore, micro-organisms could be controled effectively by 3 kGy irradiation and its shelf-life could extend to 28 days. (authors)

  4. HTS Nested magnet wound with 12 mm GdBCO tape and 4.4 mm YBCO tape

    International Nuclear Information System (INIS)

    Kang, Myung Hun; Ku, Myung Hwan; Cha, Guee Soo; Lim, Hyoung Woo

    2015-01-01

    The properties of High Temperature Superconducting (HTS) tapes are progressing, as HTS tapes evolve from 1st generation to 2nd generation. This paper presents design and construction of a 2nd generation HTS magnet consisting of two nested GdBCO and YBCO pancake coils. Two HTS tapes of different widths were used to wind the HTS nested magnet. Considering that a higher magnetic field is applied to the inner magnet than to the outer magnet, 12 mm GdBCO tape was used for winding the inner magnet, which consisted of four single pancake windings. Eight double pancake windings wound with 4.4 mm YBCO tapes were used for the outer magnet. The test results show that the central magnetic field of the HTS nested magnet was 920 mT. The measured critical currents of the inner and outer magnet at 77K were 80.8 A and 32.6 A, respectively

  5. Diagnostics of sources of disturbances and distribution of vibrations over the width of a tape in tape-feed mechanisms

    Science.gov (United States)

    Kenstavichyus, A. B. B.

    1973-01-01

    Disturbances created by certain assemblies and components of tape-feed mechanisms (TFM) and acting on a moving magnetic tape are studied. The method, based on elements of digital logic, is established by stress-strain diagrams of the longitudinal deformations and vibrations across the width of a magnetic tape. Experimental studies were carried out for determination of the functional relationships of longitudinal deformations in a section of magnetic tape to the magnitude of roller play, tension vibrations rate of movement, and elasticity of magnetic tapes. A block diagram of the measurements is shown. Appropriate digital computer algorithms and programs were proposed for statistical analysis of the data obtained. Estimates of the mathematical expectation, dispersion, intercorrelation function, energy spectral density, and distribution pattern of the random process values were calculated.

  6. Giant Clams and Rising CO2: Light May Ameliorate Effects of Ocean Acidification on a Solar-Powered Animal.

    Directory of Open Access Journals (Sweden)

    Sue-Ann Watson

    Full Text Available Global climate change and ocean acidification pose a serious threat to marine life. Marine invertebrates are particularly susceptible to ocean acidification, especially highly calcareous taxa such as molluscs, echinoderms and corals. The largest of all bivalve molluscs, giant clams, are already threatened by a variety of local pressures, including overharvesting, and are in decline worldwide. Several giant clam species are listed as 'Vulnerable' on the IUCN Red List of Threatened Species and now climate change and ocean acidification pose an additional threat to their conservation. Unlike most other molluscs, giant clams are 'solar-powered' animals containing photosynthetic algal symbionts suggesting that light could influence the effects of ocean acidification on these vulnerable animals. In this study, juvenile fluted giant clams Tridacna squamosa were exposed to three levels of carbon dioxide (CO2 (control ~400, mid ~650 and high ~950 μatm and light (photosynthetically active radiation 35, 65 and 304 μmol photons m-2 s-1. Elevated CO2 projected for the end of this century (~650 and ~950 μatm reduced giant clam survival and growth at mid-light levels. However, effects of CO2 on survival were absent at high-light, with 100% survival across all CO2 levels. Effects of CO2 on growth of surviving clams were lessened, but not removed, at high-light levels. Shell growth and total animal mass gain were still reduced at high-CO2. This study demonstrates the potential for light to alleviate effects of ocean acidification on survival and growth in a threatened calcareous marine invertebrate. Managing water quality (e.g. turbidity and sedimentation in coastal areas to maintain water clarity may help ameliorate some negative effects of ocean acidification on giant clams and potentially other solar-powered calcifiers, such as hard corals.

  7. Growth and Histological Effects to Protothaca staminea (Littleneck Clam) of Long-Term Exposure to Chlorinated Sea Water

    Energy Technology Data Exchange (ETDEWEB)

    Gibson, C. I.; Hillman, A. E.; Wilkinson, P.; Woodruff, D. L.

    1980-08-01

    There has been considerable concern about the potential for long-term effects to marine organisms from chlorinated sea water. As part of a larger study to investigate the effects of materials resulting from seawater chlorination on marine organisms, groups of littleneck clams, Protothaca staminea, were exposed to sea water that had been chlorinated. Two experiments were conducted. In one test, groups of littleneck clams were exposed to dilutions of chlorinated sea water that had average chlorine produced oxidant (CPO) concentrations of 16 {micro}g/l or less. In the second test, groups of clams were exposed to chlorinated seawater-unchlorinated seawater mixtures that had target CPO concentrations of 0, 6, 12, 25, 50 and 100 {micro}g/l. In the first experiment, length measurements were made on all clams at approximately one-month intervals for three months. In the second test, length, weight, depth, width and edge etching were used to measure growth, and subsamples were harvested and measured at one-month intervals. In addition, clams were preserved for histological examination. The clams in the first experiment all had negative growth. In the second test, growth was inhibited under all conditions through the first four months of exposure. During the last four months, there was positive signs of growth at the 0, 6 and 12 {micro}g/l CPO test conditions. Histological examination indicates that P. staminea does not adapt well to being held in aquaria. Most clams, tram all test and control conditions, showed evidence of necrosis at one month. This condition seemed to improve with longer exposure at lower CPO concentrations but persisted at CPO concentrations of 25 {micro}g/l and higher. Other histological effects were apparent at the higher exposure concentrations as the length of exposure increased.

  8. Giant Clams and Rising CO2: Light May Ameliorate Effects of Ocean Acidification on a Solar-Powered Animal.

    Science.gov (United States)

    Watson, Sue-Ann

    2015-01-01

    Global climate change and ocean acidification pose a serious threat to marine life. Marine invertebrates are particularly susceptible to ocean acidification, especially highly calcareous taxa such as molluscs, echinoderms and corals. The largest of all bivalve molluscs, giant clams, are already threatened by a variety of local pressures, including overharvesting, and are in decline worldwide. Several giant clam species are listed as 'Vulnerable' on the IUCN Red List of Threatened Species and now climate change and ocean acidification pose an additional threat to their conservation. Unlike most other molluscs, giant clams are 'solar-powered' animals containing photosynthetic algal symbionts suggesting that light could influence the effects of ocean acidification on these vulnerable animals. In this study, juvenile fluted giant clams Tridacna squamosa were exposed to three levels of carbon dioxide (CO2) (control ~400, mid ~650 and high ~950 μatm) and light (photosynthetically active radiation 35, 65 and 304 μmol photons m-2 s-1). Elevated CO2 projected for the end of this century (~650 and ~950 μatm) reduced giant clam survival and growth at mid-light levels. However, effects of CO2 on survival were absent at high-light, with 100% survival across all CO2 levels. Effects of CO2 on growth of surviving clams were lessened, but not removed, at high-light levels. Shell growth and total animal mass gain were still reduced at high-CO2. This study demonstrates the potential for light to alleviate effects of ocean acidification on survival and growth in a threatened calcareous marine invertebrate. Managing water quality (e.g. turbidity and sedimentation) in coastal areas to maintain water clarity may help ameliorate some negative effects of ocean acidification on giant clams and potentially other solar-powered calcifiers, such as hard corals.

  9. Acidified seawater increases accumulation of cobalt but not cesium in manila clam Ruditapes philippinarum.

    Science.gov (United States)

    Sezer, Narin; Kocaoğlan, Hasan Oğuz; Kılıç, Önder; Lacoue-Labarthe, Thomas; Belivermiş, Murat

    2018-04-01

    The pH of seawater around the world is expected to continue its decline in the near future in response to ocean acidification that is driven by heightened atmospheric CO 2 emissions. Concomitantly, economically-important molluscs that live in coastal waters including estuaries and embayments, may be exposed to a wide assortment of contaminants, including trace metals and radionuclides. Seawater acidification may alter both the chemical speciation of select elements as well as the physiology of organisms, and may thus pose at risk to many shellfish species, including the manila clam Ruditapes philippinarum. The bioconcentration efficiency of two common radionuclides associated with the nuclear fuel cycle, 134 Cs and 57 Co, were investigated by exposing live clams to dissolved 134 Cs and 57 Co at control (pH = 8.1) and two lowered pH (pH = 7.8 and 7.5) levels using controlled aquaria. The uptake and depuration kinetics of the two radionuclides in the whole-body clam were followed for 21 and 35 days, respectively. At steady-state equilibrium, the concentration factor (CF ss ) for 57 Co increased as the pH decreased (i.e. 130 ± 5, 194 ± 6, and 258 ± 10 at pH levels 8.1, 7.8 and 7.5, respectively), whereas the 134 Cs uptake was not influenced by a change in pH conditions. During depuration, the lowest depuration rate constant of 57 Co by the manila clam was observed at the intermediate pH of 7.8. An increase in the accumulation of 57 Co at the intermediate pH value was thought to be caused mainly by the aragonitic shell of the clam, as well as the low salinity and alkalinity of seawater used in the experiment. Considering that accumulation consists of uptake and depuration, among the three pH conditions moderately acidified seawater enhanced most the accumulation of 57 Co. Accumulation of 134 Cs was not strongly influenced by a reduced pH condition, as represented by an analogous uptake constant rate and CF ss in each treatment. Such results suggest that

  10. Toxicological effects of paracetamol on the clam Ruditapes philippinarum: exposure vs recovery.

    Science.gov (United States)

    Nunes, Bruno; Nunes, Joana; Soares, Amadeu M V M; Figueira, Etelvina; Freitas, Rosa

    2017-11-01

    Exposure of wild organisms to anthropogenic substances never follows a definite time-course and pulsed events can often determine biological responses to such chemicals, confounding the interpretation of toxicological data. This is the case of specific chemicals such as pharmaceutical drugs, which are commonly released by sewage systems into sensitive areas, including estuaries. The presence and amount of these chemicals in the wild can be modulated by events such as dilution due to heavy rain, floods, or by varying patterns of domestic water use (daily vs. seasonal). The present study aimed to obtain additional data about the toxicity of paracetamol towards the marine clam species Ruditapes philippinarum, following realistic modes of exposure. Thus, the toxicity assessment was made after an acute exposure to different concentrations of paracetamol, followed by a recovery period. The adopted toxicological endpoints included energy-related parameters (glycogen content, GLY; protein content, PROT; electron transport system activity, ETS), activity of antioxidant and biotransformation enzymes (superoxide dismutase, SOD; glutathione peroxidase, GPx; Glutathione-S-transferases, GSTs), levels of reduced glutathione (GSH), neurotoxicity (cholinesterases activity, ChEs), and indicators of oxidative damage (lipid peroxidation, LPO). The here obtained results showed an increase in SOD and GPx activities after exposure. In organisms exposed to the highest concentration tested it was also possible to observe a significant increase in GSTs activity. However, these alterations in the antioxidant defence system were not able to prevent the occurrence of oxidative stress in exposed organisms. Furthermore, exposure to paracetamol induced neurotoxicity in clams, with a concentration-dependent ChEs inhibition along the exposure concentrations. Exposure to paracetamol also led to an increase of GLY content which resulted from metabolic activity depression along the increasing exposure

  11. Simulation and analysis of tape spring for deployed space structures

    Science.gov (United States)

    Chang, Wei; Cao, DongJing; Lian, MinLong

    2018-03-01

    The tape spring belongs to the configuration of ringent cylinder shell, and the mechanical properties of the structure are significantly affected by the change of geometrical parameters. There are few studies on the influence of geometrical parameters on the mechanical properties of the tape spring. The bending process of the single tape spring was simulated based on simulation software. The variations of critical moment, unfolding moment, and maximum strain energy in the bending process were investigated, and the effects of different radius angles of section and thickness and length on driving capability of the simple tape spring was studied by using these parameters. Results show that the driving capability and resisting disturbance capacity grow with the increase of radius angle of section in the bending process of the single tape spring. On the other hand, these capabilities decrease with increasing length of the single tape spring. In the end, the driving capability and resisting disturbance capacity grow with the increase of thickness in the bending process of the single tape spring. The research has a certain reference value for improving the kinematic accuracy and reliability of deployable structures.

  12. Systematic Review of the Effect of Taping Techniques on Patellofemoral Pain Syndrome.

    Science.gov (United States)

    Logan, Catherine A; Bhashyam, Abhiram R; Tisosky, Ashley J; Haber, Daniel B; Jorgensen, Anna; Roy, Adam; Provencher, Matthew T

    Taping is commonly used in the management of several musculoskeletal conditions, including patellofemoral pain syndrome (PFPS). Specific guidelines for taping are unknown. To investigate the efficacy of knee taping in the management of PFPS. Our hypothesis was that tension taping and exercise would be superior to placebo taping and exercise as well as to exercise or taping alone. The PubMed/MEDLINE, Cochrane, Rehabilitation and Sports Medicine Source, and CINAHL databases were reviewed for English-language randomized controlled trials (RCTs) evaluating the efficacy of various taping techniques that were published between 1995 and April 2015. Keywords utilized included taping, McConnell, kinesio-taping, kinesiotaping, patellofemoral pain, and knee. Studies included consisted of RCTs (level 1 or 2) with participants of all ages who had anterior knee or patellofemoral pain symptoms and had received nonsurgical management using any taping technique. Systematic review. Level 2. A checklist method was used to determine selection, performance, detection, and attrition bias for each article. A quality of evidence grading was then referenced using the validated PEDro database for RCTs. Three difference comparison groups were compared: tension taping and exercise versus placebo taping and exercise (group 1), placebo taping and exercise versus exercise alone (group 2), and tension taping and exercise versus taping alone (group 3). Five RCTs with 235 total patients with multiple intervention arms were included. Taping strategies included McConnell and Kinesiotaping. Visual analog scale (VAS) scores indicated improvement in all 3 comparison groups (group 1: 91 patients, 39% of total, mean VAS improvement 44.9 [tension taping + exercise] vs 66 [placebo taping + exercise]; group 2: 56 patients, 24% of total, mean VAS improvement 66 [placebo taping + exercise] vs 47.6 [exercise alone]; and group 3: 112 patients, 48% of total, mean VAS improvement 44.9 [tension taping + exercise

  13. Engineering Critical Current Density Improvement in Ag- Bi-2223 Tapes

    DEFF Research Database (Denmark)

    Wang, W. G.; Seifi, Behrouz; Eriksen, Morten

    2000-01-01

    Ag alloy sheathed Bi-2223 multifilament tapes were produced by the powder-in-tube method. Engineering critical current density improvement has been achieved through both enhancement of critical current density by control of the thermal behavior of oxide powder and by an increase of the filling...... factor of the tapes. Phase evolution at initial sintering stage has been studied by a quench experiment in Ag-Bi-2223 tapes. The content, texture, and microstructure of various phases were determined by XRD and SEM. A novel process approach has been invented in which square wire was chosen rather than...

  14. Preparing superconducting nanopowder based YBCO/Ag tapes

    DEFF Research Database (Denmark)

    Paturi, P.; Raittila, J.; Grivel, J.C.

    2002-01-01

    YBCO nanopowder consisting of 1-3 nm thick and 40 nm wide particles has been used to make silver clad superconducting tapes. After annealing in nitrogen at 945 degreesC for 10 h a critical current of 5.02 A (3300 A/cm(2)) was attained, Annealing in mixed atmosphere of oxygen and nitrogen was also...... carried out and this procedure produced tapes with a critical current of 2.83 A (2200 A/cm(2)). These tapes show very good characteristics in magnetic fields. (C) 2002 Elsevier Science B.V. All rights reserved....

  15. An automated magnetic tape vault at CERN computer center

    CERN Multimedia

    Claudia Marcelloni

    2008-01-01

    The rapidly changing data processing landscape the underlying long-term storage technology remains the tried and tested magnetic tape. This robust and mature technology is used to store the complete LHC data set, from which a fraction of the data is copied to overlying disk caches for fast and widespread access. The handling of the magnetic tape cartridges is now fully automated, as they are racked in vaults where they are moved between the storage shelves and the tape drives by robotic arms.

  16. Purification and Characterization of Hemagglutinating Proteins from Poker-Chip Venus (Meretrix lusoria and Corbicula Clam (Corbicula fluminea

    Directory of Open Access Journals (Sweden)

    Chin-Fu Cheng

    2012-01-01

    Full Text Available Hemagglutinating proteins (HAPs were purified from Poker-chip Venus (Meretrix lusoria and Corbicula clam (Corbicula fluminea using gel-filtration chromatography on a Sephacryl S-300 column. The molecular weights of the HAPs obtained from Poker-chip Venus and Corbicula clam were 358 kDa and 380 kDa, respectively. Purified HAP from Poker-chip Venus yielded two subunits with molecular weights of 26 kDa and 29 kDa. However, only one HAP subunit was purified from Corbicula clam, and its molecular weight was 32 kDa. The two Poker-chip Venus HAPs possessed hemagglutinating ability (HAA for erythrocytes of some vertebrate animal species, especially tilapia. Moreover, HAA of the HAP purified from Poker-chip Venus was higher than that of the HAP of Corbicula clam. Furthermore, Poker-chip Venus HAPs possessed better HAA at a pH higher than 7.0. When the temperature was at 4°C–10°C or the salinity was less than 0.5‰, the two Poker-chip Venus HAPs possessed better HAA compared with that of Corbicula clam.

  17. Low cycle fatigue properties of CLAM steel at 450 °C and 550 °C

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Yanyun; Zhai, Xiangwei; Liu, Shaojun, E-mail: shaojun.liu@fds.org.cn

    2016-11-15

    Highlights: • Low cycle fatigue properties of CLAM steel were investigated at 450 °C and 550 °C. • CLAM steel showed the continuous softening up to fail failure under cyclic loading. The degree of softening increased with increasing temperature. • Dislocation density decrease and subgrain coarsening during the test process were the possible reasons for the cyclic softening of the CLAM steel. - Abstract: The low cycle fatigue behavior of China Low Activation Martensitic (CLAM) steel has been studied using a constant strain rate of 8 × 10{sup −3}/s with the strain amplitudes ranging from 0.3% to 0.8% at 450 °C and 550 °C. Cyclic stress response showed a gradual softening until complete failure. The fatigue life decreased with increasing test temperature, and the effect of temperature on fatigue life was more pronounced at lower strain amplitudes. The cyclic deformation behavior at different temperatures has been analyzed according to the hysteresis loop, and the mechanism of cyclic softening was interpreted in view of the changes taking place in dislocation density and lath structures. Evaluation of low cycle fatigue properties of CLAM steel at 450 °C and 550 °C can help in design of the Chinese Test Blanket Module (TBM) for the International Thermonuclear Experimental Reactor (ITER) and a future fusion power plant.

  18. In situ studies with Asian clams (Carbacula fluminea) detect acid mine drainage and nutrient inputs in low-order streams

    International Nuclear Information System (INIS)

    Soucek, D. J.; Schmidt, T. S.; Cherry, D. S.

    2001-01-01

    This study evaluates the correlation between transplanted Asiatic clam and indigenous community responses to acid mine drainage and nutrient loading in first-to-third-order streams, by comparing the toxicological endpoints of clam survival and growth with benthic macro-invertebrate community indices as community responses to both acid mine drainage and nutrient loading. Clam survival was found to be positively correlated with water column pH and negatively correlated with conductivity and metal concentrations. There was also a positive correlation with the relative abundance of the macro-invertebrate Ephemeroptera, the most sensitive taxonomic group, to acid mine drainage in this watershed. No correlation was found between clam growth and acid mine drainage inputs, but there was evidence of positive correlation with nitrate concentrations and the relative abundance of collector-filterer functional feeding groups. These results suggest that clam growth is related to nutrient levels and accurately reflect benthic macro-invertebrate responses to nutrient loading. 28 refs., 5 tabs., 1 fig

  19. Diversity of lactic acid bacteria in sian-sianzih (fermented clams), a traditional fermented food in Taiwan.

    Science.gov (United States)

    Chen, Yi-sheng; Wu, Hui-chung; Li, Ya-han; Leong, Kun-hon; Pua, Xiao-hui; Weng, Ming-kai; Yanagida, Fujitoshi

    2012-01-30

    Sian-sianzih (fermented clams) is a popular traditional fermented food in Taiwan. The lactic acid bacteria (LAB) microflora in sian-sianzih have not been studied in detail. In this study, LAB from sian-sianzih were isolated, characterized and identified. A total of 186 cultures of LAB were isolated from seven sian-sianzih samples and 29 cultures were isolated from its main raw substrate: clams. The identification results revealed up to 11 distinct bacterial species belonging to five genera in sian-sianzih, and three species belonging to two genera in clams. The most common bacterial genera in sian-sianzih were Lactobacillus and Weissella, followed by Leuconostoc, Pediococcus and Lactococcus. A regional similarity in LAB, with differences in diversity, was observed in the current study. On the other hand, Lactococcus lactis subsp. lactis was the most common species found in raw clam samples. The results also suggested that greater LAB diversity could be observed in wild clams than in cultured ones. Furthermore, antibacterial activities of the isolates were determined, and one Weisella hellenica strain showed inhibitory activity against the indicator strain Lactobacilluas sakei JCM 1157(T) . A sensory assessment of seven sian-sianzih samples was also performed and the results indicated that diversity of LAB has a great effect on its aroma and taste formation. The results demonstrate that various LAB species are distributed in sian-sianzih and have a great effect on the flavor of sian-sianzih. Copyright © 2011 Society of Chemical Industry.

  20. A novel approach for acid mine drainage pollution biomonitoring using rare earth elements bioaccumulated in the freshwater clam Corbicula fluminea.

    Science.gov (United States)

    Bonnail, Estefanía; Pérez-López, Rafael; Sarmiento, Aguasanta M; Nieto, José Miguel; DelValls, T Ángel

    2017-09-15

    Lanthanide series have been used as a record of the water-rock interaction and work as a tool for identifying impacts of acid mine drainage (lixiviate residue derived from sulphide oxidation). The application of North-American Shale Composite-normalized rare earth elements patterns to these minority elements allows determining the origin of the contamination. In the current study, geochemical patterns were applied to rare earth elements bioaccumulated in the soft tissue of the freshwater clam Corbicula fluminea after exposure to different acid mine drainage contaminated environments. Results show significant bioaccumulation of rare earth elements in soft tissue of the clam after 14 days of exposure to acid mine drainage contaminated sediment (ΣREE=1.3-8μg/gdw). Furthermore, it was possible to biomonitor different degrees of contamination based on rare earth elements in tissue. The pattern of this type of contamination describes a particular curve characterized by an enrichment in the middle rare earth elements; a homologous pattern (E MREE =0.90) has also been observed when applied NASC normalization in clam tissues. Results of lanthanides found in clams were contrasted with the paucity of toxicity studies, determining risk caused by light rare earth elements in the Odiel River close to the Estuary. The current study purposes the use of clam as an innovative "bio-tool" for the biogeochemical monitoring of pollution inputs that determines the acid mine drainage networks affection. Copyright © 2017 Elsevier B.V. All rights reserved.

  1. Effect of post-weld heat treatment on the mechanical properties of CLAM/316L dissimilar joint

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Junyu [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); University of Science and Technology of China, Hefei, Anhui 230027 (China); Huang, Bo [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Wu, Qingsheng, E-mail: qingsheng.wu@fds.org.cn [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Li, Chunjing; Huang, Qunying [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China)

    2015-11-15

    Highlights: • Dissimilar joints between CLAM and 316L steels welded by TIG were investigated. • After PWHTs, the hardening in HAZ on the CLAM steel side decreased remarkably. • Tempering at 740 °C for 2 h was considered as the preferable treatment rule. - Abstract: Dissimilar welding between China low activation martensitic (CLAM) steel and 316L austenitic stainless steel was investigated to achieve the reliable connection between test blanket modules (TBMs) and piping system in the international thermonuclear experimental reactor (ITER). The dissimilar joints were welded by tungsten inert gas (TIG) welding process with a filler material type-309. In order to stabilize the microstructure and improve the strength and toughness, post-weld heat treatments (PWHTs) of tempering at 740 °C, 780 °C and 820 °C, respectively, for 2 h were performed. The microstructure observation showed that tempering at 740 °C for 2 h was the preferable PWHT rule in this work. After the treatment, the hardening in heat affected zone (HAZ) on the CLAM steel side decreased remarkably. The tensile strength of the joint was roughly the same as that of the base metal. The impact toughness of HAZ on the CLAM steel side was 77% of that of the base metal. The absorbed energy of HAZ of 316L steel decreased by 93 J, and that of weld metal (WM) was 110 J after the treatment.

  2. Shuttle-Data-Tape XML Translator

    Science.gov (United States)

    Barry, Matthew R.; Osborne, Richard N.

    2005-01-01

    JSDTImport is a computer program for translating native Shuttle Data Tape (SDT) files from American Standard Code for Information Interchange (ASCII) format into databases in other formats. JSDTImport solves the problem of organizing the SDT content, affording flexibility to enable users to choose how to store the information in a database to better support client and server applications. JSDTImport can be dynamically configured by use of a simple Extensible Markup Language (XML) file. JSDTImport uses this XML file to define how each record and field will be parsed, its layout and definition, and how the resulting database will be structured. JSDTImport also includes a client application programming interface (API) layer that provides abstraction for the data-querying process. The API enables a user to specify the search criteria to apply in gathering all the data relevant to a query. The API can be used to organize the SDT content and translate into a native XML database. The XML format is structured into efficient sections, enabling excellent query performance by use of the XPath query language. Optionally, the content can be translated into a Structured Query Language (SQL) database for fast, reliable SQL queries on standard database server computers.

  3. How to make sticky tapes stickier

    Science.gov (United States)

    Ponson, Laurent; Xia, Shuman; Ravichandran, Guruswami; Bhattacharya, Kaushik; California Institute of Technology Team

    2011-03-01

    Thin film adhesives have become increasingly important in various applications such as packaging and coating, and we benefit daily of their adhesion properties by using various kinds of tapes. Despite the apparent simplicity of these systems, a certain number of questions remain open. In particular, important efforts have been deployed recently to understand the effect of the complex tridimensional and highly heterogeneous structure at the interface of some adhesives, such as the one encountered in nature like the geckos toes. Although inspired by these natural adhesives, we studied a much simpler system, and however largely unexplored: a thin film with spatially varying adhesion energy and elastic properties. We will show how these heterogeneities introduced at the microscale can generate quite unexpected macroscopic behaviors, and that one can this way design stronger adhesives with new properties. Beyond their practical interests, these systems involve long range elastic interactions and heterogeneities resulting in a rich and complex physics that will be illustrated through experimental examples and their theoretical interpretation.

  4. NMR-Based Metabolomic Investigations on the Differential Responses in Adductor Muscles from Two Pedigrees of Manila Clam Ruditapes philippinarum to Cadmium and Zinc

    Directory of Open Access Journals (Sweden)

    Junbao Yu

    2011-09-01

    Full Text Available Manila clam Ruditapes philippinarum is one of the most important economic species in shellfishery in China due to its wide geographic distribution and high tolerance to environmental changes (e.g., salinity, temperature. In addition, Manila clam is a good biomonitor/bioindicator in “Mussel Watch Programs” and marine environmental toxicology. However, there are several pedigrees of R. philippinarum distributed in the marine environment in China. No attention has been paid to the biological differences between various pedigrees of Manila clams, which may introduce undesirable biological variation in toxicology studies. In this study, we applied NMR-based metabolomics to detect the biological differences in two main pedigrees (White and Zebra of R. philippinarum and their differential responses to heavy metal exposures (Cadmium and Zinc using adductor muscle as a target tissue to define one sensitive pedigree of R. philippinarum as biomonitor for heavy metals. Our results indicated that there were significant metabolic differences in adductor muscle tissues between White and Zebra clams, including higher levels of alanine, glutamine, hypotaurine, phosphocholine and homarine in White clam muscles and higher levels of branched chain amino acids (valine, leucine and isoleucine, succinate and 4-aminobutyrate in Zebra clam muscles, respectively. Differential metabolic responses to heavy metals between White and Zebra clams were also found. Overall, we concluded that White pedigree of clam could be a preferable bioindicator/biomonitor in marine toxicology studies and for marine heavy metals based on the relatively high sensitivity to heavy metals.

  5. Overcurrent experiments on HTS tape and cable conductor

    DEFF Research Database (Denmark)

    Tønnesen, Ole; Jensen, Kim Høj; Træholt, Chresten

    2001-01-01

    their critical current. In this light, it is important to investigate the response of HTS tapes and cable conductors to overcurrents several times the critical current. A number of experiments have been performed on HTS tapes and cable conductors, with currents up to 20 times the critical current. During...... overcurrent experiments, the voltage, and the temperature were measured as functions of time in order to investigate the dynamic behavior of the HTS tape and cable conductor. After each experiment, damage to the superconductors was assessed by measuring the critical current. Preliminary results show...... that within seconds an HTS tape (critical current=17 A) heats above room temperature with an overcurrent larger than 140 A. Similar overcurrent experiments showed that a HTS cable conductor could sustain damage with overcurrents exceeding 10 times the critical current of the cable conductor....

  6. Enhancement of heat transfer using varying width twisted tape inserts

    African Journals Online (AJOL)

    International Journal of Engineering, Science and Technology ... experimental investigations of the augmentation of turbulent flow heat transfer in a horizontal tube by means of varying width twisted tape inserts with air as the working fluid.

  7. Sun StorageTek T9940 Tape Drive

    CERN Multimedia

    2002-01-01

    Technology allowed reuse of the same data cartridge at higher capacity with later model of the tape drive hence offering significant savings of the media cost. It has been use by the CERN from 2002 to 2008.

  8. ICI optical data storage tape: An archival mass storage media

    Science.gov (United States)

    Ruddick, Andrew J.

    1993-01-01

    At the 1991 Conference on Mass Storage Systems and Technologies, ICI Imagedata presented a paper which introduced ICI Optical Data Storage Tape. This paper placed specific emphasis on the media characteristics and initial data was presented which illustrated the archival stability of the media. More exhaustive analysis that was carried out on the chemical stability of the media is covered. Equally important, it also addresses archive management issues associated with, for example, the benefits of reduced rewind requirements to accommodate tape relaxation effects that result from careful tribology control in ICI Optical Tape media. ICI Optical Tape media was designed to meet the most demanding requirements of archival mass storage. It is envisaged that the volumetric data capacity, long term stability and low maintenance characteristics demonstrated will have major benefits in increasing reliability and reducing the costs associated with archival storage of large data volumes.

  9. Taping reduces pain and disability in patients with knee osteoarthritis.

    NARCIS (Netherlands)

    Ende, E. van den

    2004-01-01

    Question: Is taping of the knee effective in improving pain and disability in patients with osteoarthritis of the knee? Design Randomised controlled trial. Setting University and private practices in Melbourne, Australia. Patients: Volunteers who responded to advertisements in local newspapers.

  10. Measure Guideline: Guidance on Taped Insulating Sheathing Drainage Planes

    Energy Technology Data Exchange (ETDEWEB)

    Grin, A. [Building Science Corporation, Somerville, MA (United States); Lstiburek, J. [Building Science Corporation, Somerville, MA (United States)

    2014-09-01

    The goal of this research is to provide durable and long-term water management solutions using exterior insulating sheathing as part of the water management system. It is possible to tape or seal the joints in insulating sheathing to create a drainage plane and even an air control layer. There exists the material durability component of the tape as well as the system durability component being the taped insulating sheathing as the drainage plane. This measure guideline provides best practice and product recommendations from the interviewed contractors and homebuilders who collectively have a vast amount of experience. Three significant issues were discussed with the group, which are required to make taped insulating sheathing a simple, long-term, and durable drainage plane: horizontal joints should be limited or eliminated wherever possible; where a horizontal joint exists use superior materials; and frequent installation inspection and regular trade training are required to maintain proper installation.

  11. Evaluation of Using Caged Clams to Monitor Contaminated Groundwater Exposure in the Near-Shore Environment of the Hanford Site 300 Area

    Energy Technology Data Exchange (ETDEWEB)

    Larson, Kyle B.; Poston, Ted M.; Tiller, Brett L.

    2008-01-31

    The Asiatic clam (Corbicula fluminea) has been identified as an indicator species for locating and monitoring contaminated groundwater in the Columbia River. Pacific Northwest National Laboratory conducted a field study to explore the use of caged Asiatic clams to monitor contaminated groundwater upwelling in the 300 Area near-shore environment and assess seasonal differences in uranium uptake in relation to seasonal flow regimes of the Columbia River. Additional objectives included examining the potential effects of uranium accumulation on growth, survival, and tissue condition of the clams. This report documents the field conditions and procedures, laboratory procedures, and statistical analyses used in collecting samples and processing the data. Detailed results are presented and illustrated, followed by a discussion comparing uranium concentrations in Asiatic clams collected at the 300 Area and describing the relationship between river discharge, groundwater indicators, and uranium in clams. Growth and survival, histology, and other sources of environmental variation also are discussed.

  12. DICOM implementation on online tape library storage system

    Science.gov (United States)

    Komo, Darmadi; Dai, Hailei L.; Elghammer, David; Levine, Betty A.; Mun, Seong K.

    1998-07-01

    The main purpose of this project is to implement a Digital Image and Communications (DICOM) compliant online tape library system over the Internet. Once finished, the system will be used to store medical exams generated from U.S. ARMY Mobile ARMY Surgical Hospital (MASH) in Tuzla, Bosnia. A modified UC Davis implementation of DICOM storage class is used for this project. DICOM storage class user and provider are implemented as the system's interface to the Internet. The DICOM software provides flexible configuration options such as types of modalities and trusted remote DICOM hosts. Metadata is extracted from each exam and indexed in a relational database for query and retrieve purposes. The medical images are stored inside the Wolfcreek-9360 tape library system from StorageTek Corporation. The tape library system has nearline access to more than 1000 tapes. Each tape has a capacity of 800 megabytes making the total nearline tape access of around 1 terabyte. The tape library uses the Application Storage Manager (ASM) which provides cost-effective file management, storage, archival, and retrieval services. ASM automatically and transparently copies files from expensive magnetic disk to less expensive nearline tape library, and restores the files back when they are needed. The ASM also provides a crash recovery tool, which enable an entire file system restore in a short time. A graphical user interface (GUI) function is used to view the contents of the storage systems. This GUI also allows user to retrieve the stored exams and send the exams to anywhere on the Internet using DICOM protocols. With the integration of different components of the system, we have implemented a high capacity online tape library storage system that is flexible and easy to use. Using tape as an alternative storage media as opposed to the magnetic disk has the great potential of cost savings in terms of dollars per megabyte of storage. As this system matures, the Hospital Information Systems

  13. Verification of the effect of surface preparation on Hot Isostatic Pressing diffusion bonding joints of CLAM steel

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Yanyun [University of Science and Technology of China, Hefei, Anhui 230027 (China); Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Li, Chunjing, E-mail: chunjing.li@fds.org.cn [Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Huang, Bo; Liu, Shaojun [Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Huang, Qunying [University of Science and Technology of China, Hefei, Anhui 230027 (China); Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China)

    2014-12-15

    Hot Isostatic Pressing (HIP) diffusion bonding with CLAM steel is the primary candidate fabrication technique for the first wall (FW) of DFLL-TBM. Surface state is one of the key factors for the joints quality. The effect of surface state prepared with grinder and miller on HIP diffusion bonding joints of CLAM steel was investigated. HIP diffusion bonding was performed at 140 MPa and 1373 K within 3 h. The mechanical properties of the joints were investigated with instrumented Charpy V-notch impact tests and the microstructures of the joints were analyzed with scanning electron microscopy (SEM). The results showed that the milled samples with fine surface roughness were more suitable for CLAM steel HIP diffusion bonding.

  14. Tape measure to aid prescription in paediatric resuscitation.

    OpenAIRE

    Hughes, G; Spoudeas, H; Kovar, I Z; Millington, H T

    1990-01-01

    A tape measure, based on 50th centile weight for height and designed to permit easy drug dosage calculation, endotracheal tube size and DC cardioversion current dosages in childrens' emergencies, was tested for reliability by medical and nursing staff with varying paediatric experience. We found that the tape measure gave a reproducible estimate of weight and suggest that its use would facilitate decision making by inexperienced medical and nursing staff in paediatric resuscitation when there...

  15. AC power losses in Bi-2223/Ag HTS tapes

    International Nuclear Information System (INIS)

    Savvides, N.; Reilly, D.; Mueller, K.-H.; Herrmann, J.

    1998-01-01

    Full text: We report measurements at 77 K of the transport ac losses of Bi-2223/Ag composite tapes. The investigated tapes vary from single filament to multifilament construction and include both conventional tapes and other conductor shapes with twisted filaments. The self-field ac losses were determined at 77 K and 60 Hz as a function of ac current amplitude (0 - 100 A). We observe different behaviour among tapes depending on their quality and strain history. For 'good' virgin tapes the experimental data are well described by the Norris equations for the dependence of power loss P on the amplitude I m of the transport current. The data of good monofilament tapes are fitted to the Norris equation P ∼ I m n for an elliptical cross section (ie. n = 3) and the data of good multifilament tapes are fitted to the Norris equation for a rectangular strip (ie. n = 4). Many specimens, however, show a range of behaviour with lower values of n. Based on our work on the effect of strain on the dc transport properties of tapes, we carried out detailed investigations of the effect of controlled applied bend strain on the ac loss. Our results show that irreversible damage to superconducting filaments (ie. cracks) cause the ac loss to rise and n to decrease with increasing strain. In addition, applied strains much greater than the irreversible strain limit cause the ac loss to increase by several orders of magnitude and become ohmic in character with n = 2. Theoretical work is in progress to model the observed behaviour

  16. Device for stretching tapes or cables intended for manipulators

    International Nuclear Information System (INIS)

    Baudoin, J.-C.; Oger, Robert.

    1975-01-01

    The invention relates to a device for stretching tapes (or cables) intended for remote handling devices. Said equipment consists of a spring system continuously applying a constant tensile stress to said tapes (or cables) in view of taking up the slack in the latter. Said spring system is fastened to a supporting bar able to be rigidly connected to a member of the remote handling device [fr

  17. Device for stretching tapes or cables intended for manipulators

    Energy Technology Data Exchange (ETDEWEB)

    Baudoin, J C; Oger, R

    1975-03-06

    The invention relates to a device for stretching tapes (or cables) intended for remote handling devices. Said equipment consists of a spring system continuously applying a constant tensile stress to said tapes (or cables) in view of taking up the slack in the latter. Said spring system is fastened to a supporting bar able to be rigidly connected to a member of the remote handling device.

  18. Outcome of transvaginal mesh and tape removed for pain only.

    Science.gov (United States)

    Hou, Jack C; Alhalabi, Feras; Lemack, Gary E; Zimmern, Philippe E

    2014-09-01

    Because there is reluctance to operate for pain, we evaluated midterm outcomes of vaginal mesh and synthetic suburethral tape removed for pain as the only indication. After receiving institutional review board approval we reviewed a prospective database of women without a neurogenic condition who underwent surgery for vaginal mesh or suburethral tape removal with a focus on pain as the single reason for removal and a minimum 6-month followup. The primary outcome was pain level assessed by a visual analog scale (range 0 to 10) at baseline and at each subsequent visit with the score at the last visit used for analysis. Parameters evaluated included demographics, mean time to presentation and type of mesh or tape inserted. From 2005 to 2013, 123 patients underwent surgical removal of mesh (69) and suburethral tape (54) with pain as the only indication. Mean followup was 35 months (range 6 to 59) in the tape group and 22 months (range 6 to 47) in the mesh group. The visual analog scale score decreased from a mean preoperative level of 7.9 to 0.9 postoperatively (p = 0.0014) in the mesh group and from 5.3 to 1.5 (p = 0.00074) in the tape group. Pain-free status, considered a score of 0, was achieved in 81% of tape and 67% of mesh cases, respectively. No statistically significant difference was found between the groups. When pain is the only indication for suburethral tape or vaginal mesh removal, a significant decrease in the pain score can be durably expected after removal in most patients at midterm followup. Copyright © 2014 American Urological Association Education and Research, Inc. Published by Elsevier Inc. All rights reserved.

  19. Forensic Pollen Evidence from Clothes by the Tape Adhesive Method

    Directory of Open Access Journals (Sweden)

    Chun-Liang Wu

    2006-06-01

    Full Text Available Collection and identification of pollen is becoming important in forensic applications. Many criminal cases have been reported to link suspects to the crime scene by analysis of pollen. Several methods have been used in the pollen collection and analysis, but they are expensive and tedious. Therefore, it is important to develop a simple method to collect pollen grains from clothes. We tried to recover pollen from clothing surface by using the sticky tapes method. The tape adhesive method has been widely used for sample collection for various purposes, but the efficiency of recovery of invisible pollen from clothes has rarely been reported. Therefore, to test the efficiency of the tape adhesive method in recovering pollen from clothes is important. The first author wore clothes that were made from textile S made by the mixture of cotton 60% and polyester fiber 40% to collect pollen from 26 different areas mostly in the northern part of Taiwan and then used cellophane tape D (Sirchie Finger Print Lab., Inc-No. 131LT4 to recover them from different body parts. Twenty-six pollen taxa were detected in different parts of clothes depending upon what kind of plant the first author stayed near. From the results, we concluded that the tape adhesive method is suitable in recovering pollen from clothes. We have suggested that the tape adhesive method could be part of methods for collecting pollen from clothes of suspects. It is simpler, faster and less expensive than other methods.

  20. Increasing the efficiency of tape-based storage backends

    CERN Document Server

    Bessone, N; Murray, S; Taurelli, G; CERN. Geneva. IT Department

    2010-01-01

    HSM systems such as the CERN’s Advanced STORage manager (CASTOR) [1] are responsible for storing Petabytes of data which is first cached on disk and then persistently stored on tape media. The contents of these tapes are regularly repacked from older, lower-density media to new-generation, higher-density media in order to free up physical space and ensure long term data integrity and availability. With the evolution of price decay and higher capacity of disk (and flash memory) based storage, our future vision for tape usage is to move away from serving on demand, random, per-file access to non-disk cached files, and to move towards loosely coupled, efficient bulk data transfers where large-volume data sets are stored and retrieved in aggregations, fully exploiting the stream-based nature of tape media. Mechanisms for grouped migration policies and priorities have been implemented, and an innovative tape format optimized for data aggregations is being developed. This new tape format will also allow for incre...

  1. Size-dependent effects of low level cadmium and zinc exposure on the metabolome of the Asian clam, Corbicula fluminea

    Energy Technology Data Exchange (ETDEWEB)

    Spann, Nicole, E-mail: nicole.spann@web.de [Department of Zoology, University of Cambridge, Downing Street, Cambridge CB2 3EJ (United Kingdom); Aldridge, David C., E-mail: da113@cam.ac.uk [Department of Zoology, University of Cambridge, Downing Street, Cambridge CB2 3EJ (United Kingdom); Griffin, Julian L., E-mail: jlg40@mole.bio.cam.ac.uk [Sanger Building, Department of Biochemistry, University of Cambridge, 80 Tennis Court Road, Cambridge CB2 1GA (United Kingdom); Jones, Oliver A.H., E-mail: o.jones@gmail.com [Sanger Building, Department of Biochemistry, University of Cambridge, 80 Tennis Court Road, Cambridge CB2 1GA (United Kingdom)

    2011-10-15

    Highlights: Small and large Corbicula fluminea were exposed to cadmium and zinc spiked sediment. Metabolomic changes in the freshwater clams were determined by NMR and GC-MS. Metabolic perturbations were related to amino acid and energy related metabolism. Small and large clams were differentiated by their metabolic composition. Size classes showed opposite responses to metal stress. - Abstract: The toxic effects of low level metal contamination in sediments are currently poorly understood. We exposed different sized Asian clams, Corbicula fluminea, to sediment spiked with environmentally relevant concentrations of either zinc, cadmium or a zinc-cadmium mixture for one week. This freshwater bivalve is well suited for sediment toxicity tests as it lives partly buried in the sediment and utilises sediment particles as a food resource. After one week, the whole tissue composition of low molecular weight metabolites was analysed by nuclear magnetic resonance spectroscopy (NMR) and gas chromatography-mass spectrometry (GC-MS). The condition index (ratio of tissue dry weight to volume inside the shell valves) was also measured. Small and large clams were clearly differentiated by their metabolic composition and the two size classes showed opposite responses to the mixture spiked sediment. No effects of zinc alone on the metabolome were found and cadmium only influenced the smaller size class. The main perturbations were seen in amino acid and energy metabolism, with small clams using amino acids as an energy resource and larger clams primarily drawing on their larger storage reserves of carbohydrates. Our study demonstrates that metabolomics is a useful technique to test for low level toxicity which does not manifest in mortality or condition index changes. The differing effects between the two size classes stress that it is important to consider age/size when conducting metabolomic and ecotoxicology assessments, since testing for the effects on only one size class makes

  2. Size-dependent effects of low level cadmium and zinc exposure on the metabolome of the Asian clam, Corbicula fluminea

    International Nuclear Information System (INIS)

    Spann, Nicole; Aldridge, David C.; Griffin, Julian L.; Jones, Oliver A.H.

    2011-01-01

    Highlights: Small and large Corbicula fluminea were exposed to cadmium and zinc spiked sediment. Metabolomic changes in the freshwater clams were determined by NMR and GC–MS. Metabolic perturbations were related to amino acid and energy related metabolism. Small and large clams were differentiated by their metabolic composition. Size classes showed opposite responses to metal stress. - Abstract: The toxic effects of low level metal contamination in sediments are currently poorly understood. We exposed different sized Asian clams, Corbicula fluminea, to sediment spiked with environmentally relevant concentrations of either zinc, cadmium or a zinc–cadmium mixture for one week. This freshwater bivalve is well suited for sediment toxicity tests as it lives partly buried in the sediment and utilises sediment particles as a food resource. After one week, the whole tissue composition of low molecular weight metabolites was analysed by nuclear magnetic resonance spectroscopy (NMR) and gas chromatography–mass spectrometry (GC–MS). The condition index (ratio of tissue dry weight to volume inside the shell valves) was also measured. Small and large clams were clearly differentiated by their metabolic composition and the two size classes showed opposite responses to the mixture spiked sediment. No effects of zinc alone on the metabolome were found and cadmium only influenced the smaller size class. The main perturbations were seen in amino acid and energy metabolism, with small clams using amino acids as an energy resource and larger clams primarily drawing on their larger storage reserves of carbohydrates. Our study demonstrates that metabolomics is a useful technique to test for low level toxicity which does not manifest in mortality or condition index changes. The differing effects between the two size classes stress that it is important to consider age/size when conducting metabolomic and ecotoxicology assessments, since testing for the effects on only one size

  3. Development of YBCO tape conductor fabrication technology

    Energy Technology Data Exchange (ETDEWEB)

    Hong, G W; Kim, C J; Lee, H G. and others

    2001-08-01

    Superconductor when fabricated into wire shape is applied for developing electric power transmission cable, transformer, generator and SMES. Such superconducting power devices are capable of maximizing the efficiency of electricity and are anticipated to contribute for solving the energy problem of humankind. Furthermore the high temperature oxide superconductor developed in late 1980s is superconducting above boiling temperature of liquid nitrogen temperature has strong potential to realize superconducting power device and a lot of researches are being done in this field. Superconducting wire is the most important core material for developing superconducting power device and thermo-mechanical powder in tube process was developed to fabricated Ag/Bi-2223 conductor in long length having high critical current carrying capacity. Several companies fabricate and sell Ag/Bi-2223 superconducting wire longer than km length and used for developed electrical power device. But because of its inherent property of sharp decrease in current carrying capacity when applying high magnetic field, the application of Bi-2223 sire is limited as low as 20 K when the power device is in operating under high magnetic field. The YBCO tape conductor has the advantages of maintaining high critical current applying high magnetic field and can be used to most of the power device without special limitation. The metal substrate having good crystallographic texture and deposition technique which can deposit the good quality superconducting thin film continuously in large area are need to fabricate coated conductor, and this technique can be applied to develop the superconducting current limiter or magnetic field shielding device. A superconducting wire for using in high magnetic field is play a critical role in developing maglev, MRI, SMES, transformer, generator and motor and the continuous film deposition technique can be applied in other industry very much.

  4. On the weld strength of in situ tape placed reinforcements on weave reinforced structures

    NARCIS (Netherlands)

    Grouve, Wouter Johannes Bernardus; Warnet, Laurent; Rietman, Bert; Akkerman, Remko

    2012-01-01

    Unidirectionally reinforced thermoplastic tapes were welded onto woven fabric reinforced laminates using a laser assisted tape placement process. A mandrel peel setup was used to quantify the interfacial fracture toughness between the tape and the laminate as a measure for weld strength. The tape

  5. A new method of measurement of tension on a moving magnetic tape

    Science.gov (United States)

    Kurtinaytis, A. K.; Lauzhinskas, Y. S.

    1973-01-01

    The possibility of no-contact measurement of the tension on a moving magnetic tape, assuming the tape is uniform, is discussed. A scheme for calculation of the natural frequency of transverse vibrations of magnetic tape is shown. Mathematical models are developed to show the relationships of the parameters. The method is applicable to the analysis of accurate tape feed mechanisms design.

  6. Presence of enteric viruses, bioaccumulation and stability in Anomalocardia brasiliana clams (Gmelin, 1791).

    Science.gov (United States)

    Souza, Doris Sobral Marques; Dominot, Ana Ferreira Ávila; Moresco, Vanessa; Barardi, Célia Regina Monte

    2018-02-02

    Bivalve mollusks are filter feeders and may accumulate human pathogens in their tissues. Many studies demonstrated human diseases associated with bivalve consumption, especially oysters. Anomalocardia brasiliana clams are distributed along the Brazilian coastal area and are an exotic ingredient for some typical dishes in Brazil. Even though there are several reports describing the contamination of oysters and mussels with human pathogens, there is a lack of studies reporting contamination of A. brasiliana with human pathogens. An evaluation of natural microbiological contamination in A. brasiliana samples over a period of 18months (November 2014 to April 2016) showed that the bacteria indices were in accordance with Brazilian regulations (E. colitime period. NoV GI was the most adsorbed virus after 24h. HAV concentration was time, reaching its highest values after 24h (times (0, 1, 1.5, 3 and 5mins), viral infectivity was evaluated using ICC-et-RT-qPCR. The temperature inside the DT remained time and after 5min of cooking the HAdV reached a decay of 90% (1 log 10 ). The results showed a real warn to the consumers that can be exposed to infectious human viruses if they eat these clams improperly cooked. HAV was the most detected virus in these animals, which may lead to outbreaks. A. brasiliana exhibited distinct behavior in NoV GI bioaccumulation and persistence, pointing to the need for further studies about the cellular ligands used by these viruses to become attached to these clams. Copyright © 2017. Published by Elsevier B.V.

  7. Prevalence of Vibrio parahaemolyticus in oyster and clam culturing environments in Taiwan.

    Science.gov (United States)

    Yu, Wei-Ting; Jong, Koa-Jen; Lin, Yu-Ren; Tsai, Shing-en; Tey, Yao Hsien; Wong, Hin-chung

    2013-01-01

    Vibrio parahaemolyticus is the most prevalent gastroenteritis pathogen in Taiwan and some other Asian countries, and it frequently occurs in oysters and other seafood. This study monitors changes in the density of V. parahaemolyticus and environmental parameters in oyster and hard clam aquacultural environments in Taiwan. Water, sediment and shellfish samples were collected from five sampling sites in 2008-2010, and analyzed for environmental physiochemical parameters, numbers of indicator bacteria (total aerobic counts, total coliforms and fecal coliforms), Vibrio and V. parahaemolyticus present. The results for open oyster farms and hard clam ponds did not differ significantly. V. parahaemolyticus was detected in 77.5, 77.5, 70.8 and 68.8% of the water, sediment, oyster and clam samples, respectively. The densities of V. parahaemolyticus were significantly higher in shellfish than in sediment or water samples, with mean values of 1.33, 1.04 and -0.02 Log CFU/g, respectively. Among these five sampling sites, Shengang and Fangyuan yielded significantly different data from those obtained at the other three sites. As determined by linear multiple regression, V. parahaemolyticus density in water samples depended significantly on the precipitation and Vibrio count, while the V. parahaemolyticus density in the sediment or shellfish samples depended significantly on the salinity of the seawater. Among 1076 isolates examined, a total of three putative pathogenic isolates were identified from 2.5% of the examined samples, and these isolates exhibited hemolytic or urease activities and the presence of gene markers for tdh, trh, type III secretion system (T3SS) 1 (vcrD1) or T3SS2α (vcrD2). The results herein may facilitate the assessment of risk associated with this pathogen in Taiwan and other geographically similar regions. Copyright © 2012 Elsevier B.V. All rights reserved.

  8. Flow structure and heat transfer in a square duct fitted with dual/quadruple twisted-tapes: Influence of tape configuration

    International Nuclear Information System (INIS)

    Eiamsa-ard, S.; Changcharoen, W.

    2015-01-01

    Numerical predictions reported of thermohydraulic characteristics of square ducts equipped with dual and quadruple twisted tapes (DTs and QTs) with different configurations. The studied cases include (1) dual co-tapes (Co-DTs), (2) dual counter-tapes (C-DTs), (3) diagonal dual counter-tapes (C-DDTs), (4) diagonal dual co-tapes (Co-DDTs), (5) quadruple co-tapes (Co-QTs), (6) quadruple counter tapes (CC-QTs) and (7) quadruple counter-tapes (PC-QTs). The results of these cases are compared with those of a smooth duct (a duct without tape insert) and also the one with a single tape (ST). The prediction involves using the RNG k-ε turbulent model under constant wall heat flux condition in the turbulent flow regime for the Reynolds number ranging from 6000 to 14000. The prediction indicates that thermohydraulic characteristics in ducts with twisted tape are strongly dependent on number and configuration of tapes. However, the influence of tape number is more significant than that of tape configuration. Heat transfer and friction increase as tape number increases. QTs offer superior heat transfer to DTs but their thermal performance factors are lower. For the tape inserts determined, DTs with diagonal configuration (Co-DDTs and C-DDTs) is the best design as the tapes offer the best thermal performance. The highest thermal performance factors given by Co-DTs, Co-DDTs, C-DTs, C-DDTs, Co-QTs, PC-QTs and CC-QTs, are around 1.21, 1.35, 1.25, 1.38, 1.08, 1.18, and 1.22, respectively

  9. Corrosion behavior of CLAM steel weldment in flowing liquid Pb-17Li at 480 °C

    International Nuclear Information System (INIS)

    Chen Xizhang; Shen Zheng; Chen Xing; Lei Yucheng; Huang Qunying

    2011-01-01

    Highlights: ► The research shows that the CLAM steel weldment have its own corrosion mechanism in liquid Pb-17Li alloy. The basic rule of the corrosion behaviour of weldments is that the coorosion rate decreases obviously with the increasing of exposed time. ► The weight loss of CLAM steel weldment is far higer than the base metal after exposed to Pb-17Li alloy. Corrosion has little effects on elements of weldment sample surfaces. And an easier corrosion area in the weld joint are found. ► A simple presumably corrosion behavior model is established. The model demonstrate that the easier corroded area will be formed when the direction of martensite laths form small-angle with the specimen surface, The easy corrosion area is the martensite lath area lack of Cr and distributes like laths, the cross-section area is 1 μm 2 to 4 μm 2, the existence of the easier corrosion area is one of the reasons that lead to the difference of the corrosion rate. - Abstract: CLAM (China Low Activation Martensitic) steel is considered as one of the candidate structural materials in liquid LiPb blanket concepts. Welding is one of the essential technologies for its practical application, CLAM steel weldment shows a great difference with base metal due to the effect of welding thermal cycle. In order to investigate the corrosion behavior and mechanism of CLAM weldments in liquid Pb-17Li, the experiments were performed by exposing the TIG weldment samples in flowing LiPb at 480 °C. The weight loss test of exposed specimens show that in 500 h, 1000 h dynamic conditions, corrosion resistance of CLAM steel weldment is poor, SEM analysis shows that the thicker martensite lath in weld area lead to higher corrosion amount, EDS results show that the influence of corrosion on surface elements is small, and surface corrosion is even, EDX analysis shows that the penetration of Pb-17Li does not exist in the joint. With the increasing of exposure time, the corrosion rate decreases

  10. Manila clams from Hg polluted sediments of Marano and Grado lagoons (Italy) harbor detoxifying Hg resistant bacteria in soft tissues

    International Nuclear Information System (INIS)

    Baldi, Franco; Gallo, Michele; Marchetto, Davide; Faleri, Claudia; Maida, Isabel; Fani, Renato

    2013-01-01

    A mechanism of mercury detoxification has been suggested by a previous study on Hg bioaccumulation in Manila clams (Ruditapes philippinarum) in the polluted Marano and Grado lagoons and in this study we demonstrate that this event could be partly related to the detoxifying activities of Hg-resistant bacteria (MRB) harbored in clam soft tissues. Therefore, natural clams were collected in six stations during two different periods (winter and spring) from Marano and Grado Lagoons. Siphons, gills and hepatopancreas from acclimatized clams were sterile dissected to isolate MRB. These anatomical parts were glass homogenized or used for whole, and they were lying on a solid medium containing 5 mg l −1 HgCl 2 and incubated at 30 °C. A total of fourteen bacterial strains were isolated and were identified by 16S rDNA sequencing and analysis, revealing that strains were representative of eight bacterial genera, four of which were Gram-positive (Enterococcus, Bacillus, Jeotgalicoccus and Staphylococcus) and other four were Gram-negative (Stenotrophomonas, Vibrio, Raoultella and Enterobacter). Plasmids and merA genes were found and their sequences determined. Fluorescence in situ hybridization (FISH) technique shows the presence of Firmicutes, Actinobacteria and Gammaproteobacteria by using different molecular probes in siphon and gills. Bacterial clumps inside clam flesh were observed and even a Gram-negative endosymbiont was disclosed by transmission electronic microscope inside clam cells. Bacteria harbored in cavities of soft tissue have mercury detoxifying activity. This feature was confirmed by the determination of mercuric reductase in glass-homogenized siphons and gills. -- Highlights: ► We isolated Gram-positive and Gram-negative Hg resistant strains from soft tissues of Ruditapes philippinarum. ► We identify 14 mercury resistant strains by 16S rRNA gene sequences. ► Bacteria in siphon and gill tissues of clams were observed by TEM and identified with

  11. Manila clams from Hg polluted sediments of Marano and Grado lagoons (Italy) harbor detoxifying Hg resistant bacteria in soft tissues

    Energy Technology Data Exchange (ETDEWEB)

    Baldi, Franco [Dipartimento di Scienze Molecolari e Nanosistemi, Cà Foscari University of Venice, Dorsoduro 2137, 30123 Venice (Italy); Gallo, Michele; Marchetto, Davide [Dipartimento di Scienze Molecolari e Nanosistemi, Cà Foscari University of Venice, Dorsoduro 2137, 30123 Venice (Italy); Faleri, Claudia [Department of Environmental Science ‘G. Sarfatti’, University of Siena, 53100 Siena (Italy); Maida, Isabel; Fani, Renato [Dipartimento di Biologia Evoluzionistica, Via Romana, 17, University of Florence, 50125 Florence (Italy)

    2013-08-15

    A mechanism of mercury detoxification has been suggested by a previous study on Hg bioaccumulation in Manila clams (Ruditapes philippinarum) in the polluted Marano and Grado lagoons and in this study we demonstrate that this event could be partly related to the detoxifying activities of Hg-resistant bacteria (MRB) harbored in clam soft tissues. Therefore, natural clams were collected in six stations during two different periods (winter and spring) from Marano and Grado Lagoons. Siphons, gills and hepatopancreas from acclimatized clams were sterile dissected to isolate MRB. These anatomical parts were glass homogenized or used for whole, and they were lying on a solid medium containing 5 mg l{sup −1} HgCl{sub 2} and incubated at 30 °C. A total of fourteen bacterial strains were isolated and were identified by 16S rDNA sequencing and analysis, revealing that strains were representative of eight bacterial genera, four of which were Gram-positive (Enterococcus, Bacillus, Jeotgalicoccus and Staphylococcus) and other four were Gram-negative (Stenotrophomonas, Vibrio, Raoultella and Enterobacter). Plasmids and merA genes were found and their sequences determined. Fluorescence in situ hybridization (FISH) technique shows the presence of Firmicutes, Actinobacteria and Gammaproteobacteria by using different molecular probes in siphon and gills. Bacterial clumps inside clam flesh were observed and even a Gram-negative endosymbiont was disclosed by transmission electronic microscope inside clam cells. Bacteria harbored in cavities of soft tissue have mercury detoxifying activity. This feature was confirmed by the determination of mercuric reductase in glass-homogenized siphons and gills. -- Highlights: ► We isolated Gram-positive and Gram-negative Hg resistant strains from soft tissues of Ruditapes philippinarum. ► We identify 14 mercury resistant strains by 16S rRNA gene sequences. ► Bacteria in siphon and gill tissues of clams were observed by TEM and identified

  12. ALAM/CLAM and some applications of computer algebra systems to problems in general relativity

    International Nuclear Information System (INIS)

    Russell-Clark, R.A.

    1973-01-01

    This paper is divided into three parts. Part A presents a historical survey of the development of the system, a brief description of its features and, finally, a critical assessment. ALAM and CLAM have been used in many problems in General Relativity; the vast majority of these belong to a set of standard calculations termed ''metric applications''. However, four large non-standard applications have been attempted successfully and these are described in Part B. CAMAL is the only other system which has been used extensively for work in relativity. CAMAL has played an important role in two research projects and details of these are given in Part C

  13. Expression of cyp1a protein in the freshwater clam Corbicula fluminea (Müller

    Directory of Open Access Journals (Sweden)

    Vranković Jelena

    2011-01-01

    Full Text Available We investigated the expression of CYP1A in the foot, gill and visceral mass of the freshwater clam Corbicula fluminea in relation to polychlorinated biphenyls (PCBs exposure. Different PCBs congeners were found in the foot and visceral mass, while the expression of CYP1A was observed only in the visceral mass. However the level of CYP1A expression in the visceral mass was not related to the level of PCBs present in the tissue. Our results indicate a higher rate of biotransformation and lower threshold of CYP1A induction in the visceral mass compared with other tissues.

  14. Reproductive Cycle of Hard Clam, Meretrix lyrata Sowerby, 1851 (Bivalvia: Veneridae) from Sarawak, Malaysia.

    Science.gov (United States)

    Hamli, Hadi; Idris, Mohd Hanafi; Rajaee, Amy Halimah; Kamal, Abu Hena Mustafa

    2015-12-01

    A study of the reproductive cycle of the hard clam, Meretrix lyrata, was documented based on histological observation and Gonad Index (GI). Samples were taken from estuarine waters of the Buntal River in Sarawak, Malaysia. The gonad of M. lyrata started to develop in September 2013. Gametogenesis continued to develop until the maturation and spawning stage from February to April 2014. The GI pattern for a one-year cycle showed a significant correlation with chlorophyll a. The corresponding GI with chlorophyll a suggested that the development of the reproductive cycle of M. lyrata required a high amount of food to increase gametogenesis.

  15. Obituary: Gerald Frederick Tape, 1915-2005

    Science.gov (United States)

    Hughes, Robert E.

    2007-12-01

    Gerald Frederick Tape, a distinguished science statesman and administrator, died on November 20, 2005. Jerry, as he was known to all, took on many diverse and important responsibilities throughout his life and dealt with them with quiet authority and grace. This was the hallmark of his life. The Board of Trustees of Associated Universities, Inc., which he served for many years, expressed this in its condolences, writing "Jerry personified integrity, thoroughness and dedication. His sensitivity for the views of others, his sincerity, his personal commitment, his calm approach and his unfailing good humor were all greatly admired and respected." Jerry was born in Ann Arbor, Michigan on May 29, 1915 but grew up in Milan, a nearby country farm community, and in Ypsilanti where his father was Principal of Michigan State Normal College, which later became Eastern Michigan University (EMU). It was there that he first became interested in physics. It was there also that he met and courted Josephine Waffen, who later would become his wife for more than sixty-six years and fill their lives with three loving sons, Walter, James, and Thomas. Upon graduation from EMU, Jerry was awarded a scholarship that took him to the University of Michigan where he earned a Ph.D. in Physics, researching the decay modes of the radioisotopes of iodine. In the Fall of 1939, during the waning days of the Great Depression, he was offered an Instructorship in the Physics Department of Cornell University, a promising start for a fruitful academic career. He brought his bride Jo to Ithaca and joined the cyclotron group under Robert Bacher and Willy Higginbotham while devising a laboratory course in nuclear techniques for graduate students. Bacher and Higginbotham soon left Cornell to join a new wartime laboratory at the Massachusetts Institute of Technology (MIT) and many other colleagues were "drafted" for war work. Bacher persuaded Jerry to join him at the MIT Radiation Laboratory in February

  16. Radiographic Outcomes of Postoperative Taping Following Hallux Valgus Correction.

    Science.gov (United States)

    Ponzio, Danielle Y; Pedowitz, David I; Verma, Kushagra; Maltenfort, Mitchell G; Winters, Brian S; Raikin, Steven M

    2015-07-01

    Traditionally, hallux valgus operative correction has been accompanied by serial spica taping of the great toe during the postoperative period. We retrospectively reviewed 187 adult patients who underwent proximal first metatarsal osteotomy with a modified McBride procedure in 2008-2009 (n = 83) and 2011-2012 (n = 104). Postoperatively, to maintain the corrected position of the hallux, patients from 2008 through 2009 underwent weekly spica taping, while patients from 2011 through 2012 utilized a toe separator. The hallux valgus angle (HVA) and intermetatarsal angle (IMA) were measured using anteroposterior weight-bearing preoperative, 2-week postoperative non-weight-bearing, and 3-month weight-bearing final follow-up radiographs. A mixed-effects linear regression model identified differences between the treatment groups over time, and a t test compared actual radiographic differences at final follow-up. The mixed-effects model revealed no significant difference in the HVA over time when comparing patients taped to those not taped at the preoperative (33 ± 6 vs 33 ± 6), 2-week postoperative (10 ± 7 vs 9 ± 6), and 3-month follow-up (14 ± 6 vs 11 ± 7) visits (P = .08). At final follow-up, the HVA was lower for the group that was not taped, but the difference (2.5 degrees) was below the minimal clinically important difference (MCID) (P = .015, 95% CI 0.5-4.5). For IMA, there was improved maintenance of correction over time in the patients that were not taped compared to those taped at the preoperative (15 ± 3 vs 15 ± 3), 2-week postoperative (2 ± 2 vs 3 ± 3), and 3-month follow-up (5 ± 4 vs 7 ± 4) visits (P = .002). At final follow-up, the IMA was lower for the group that was not taped, but the difference (1.7 degrees) was below the MCID (P = .004, 95% CI 0.7-2.9). We report no radiographic benefit of postoperative taping after hallux valgus correction. The present study challenges the previous dogma of postoperative spica taping as the protocol is cost and

  17. Red Tape dan Perilaku Masyarakat dalam Pelayanan Izin Usaha Perdagangan di Kota Makassar

    OpenAIRE

    Lukman, Lukman

    2015-01-01

    : Red tape as pathology has long been the focus of an expert study of bureaucracy. Early scholarly attempts conceptualized red tape at the individual level as in Merton's classic thesis (1940) about goal displacement. Waldo (1946) one man's red tape is another man's system. Kaufman (1977) one person's red tape may be another's treasured safeguard. Osborne and Gaebler (1992) good people trapped in bad systems. Bozeman and Feneey (2011) red tape is often used as a synonym of the term procedures...

  18. Accelerated aging studies and environmental stability of prototype tamper tapes

    Energy Technology Data Exchange (ETDEWEB)

    Wright, B.W.; Wright, C.W. [Pacific Northwest Lab., Richland, WA (United States); Bunk, A.R. [Battelle Columbus Lab., OH (United States)] [and others

    1995-05-01

    This report describes the results of accelerated aging experiments (weathering) conducted on prototype tamper tapes bonded to a variety of surface materials. The prototype tamper tapes were based on the patented Confirm{reg_sign} tamper-indicating technology developed and produced by 3M Company. Tamper tapes bonded to surfaces using pressure sensitive adhesive (PSA) and four rapid-set adhesives were evaluated. The configurations of the PSA-bonded tamper tapes were 1.27-cm-wide Confirm{reg_sign} 1700 windows with vinyl underlay and 2.54-cm-wide Confirm{reg_sign} 1700 windows with vinyl and polyester underlays. The configurations of the rapid-set adhesive-bonded tamper tapes were 2.54-cm-wide Confirm{reg_sign} (1700, 1500 with and without primer, and 1300) windows with vinyl underlay. Surfaces used for bonding included aluminum, steel, stainless steel, Kevlar{reg_sign}, brass, copper, fiberglass/resin with and without gel coat, polyurethane-painted steel, acrylonitrile:butadiene:styrene plastic, polyester fiberglass board, Lexan polycarbonate, and cedar wood. Weathering conditions included a QUV cabinet (ultraviolet light at 60{degrees}C, condensing humidity at 40{degrees}C), a thermal cycling cabinet (-18{degrees}C to 46{degrees}C), a Weather-O-Meter (Xenon lamp), and exposure outdoors in Daytona Beach, Florida. Environmental aging exposures lasted from 7 weeks to 5 months. After exposure, the tamper tapes were visually examined and tested for transfer resistance. Tamper tapes were also exposed to a variety of chemical liquids (including organic solvents, acids, bases, and oxidizing liquids) to determine chemical resistance and to sand to determine abrasion resistance.

  19. Effects of ultrasound therapy with taping PNF training and PNF training with taping in treatment and rehabilitation of sports injuries of high ankle sprain

    Directory of Open Access Journals (Sweden)

    D L Charly Daniel

    2017-01-01

    Conclusions: It was concluded that combining ultrasound with taping and PNF training with taping were found to be more beneficial in the treatment and rehabilitation of high ankle sprain injury. The combined effect of UT, PNF training, and taping may be explored by future researchers.

  20. Comparison of corrosion behavior of EUROFER and CLAM steels in flowing Pb–15.7Li

    Energy Technology Data Exchange (ETDEWEB)

    Konys, J., E-mail: juergen.konys@kit.edu [Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Krauss, W. [Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Zhu, Z.; Huang, Q. [Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China)

    2014-12-15

    Ferritic martensitic steels are envisaged to be applied as structural materials in HCLL blanket systems. Their compatibility with the liquid breeder, which is in direct contact with the structural alloy, will be essential for reliable and safe operation of the designed blankets. Formerly performed corrosion tests of RAFM steels in PICOLO loop of KIT were mainly done at high flow velocities, e.g., 0.22 m/s and delivered severe attack with material loss rates above 400 μm/yr at 823 K. Meanwhile, flow velocities for corrosion testing have been reduced into the “cm range” to be near fusion relevant conditions. Among the international ITER-partners, many varieties of RAFM steels have been developed and manufactured within the last decade, e.g., the so-called Chinese Low Activation Martensitic steel (CLAM). In this paper, the long term corrosion behavior of EUROFER and CLAM steel in flowing Pb–15.7Li will be presented at a flow velocity of about 0.10 m/s and compared with earlier obtained results of RAFM steels exposed at other operation parameters of PICOLO loop. The observed corrosion attack is near 220 μm/yr and fits well to predictions made by MATLIM-modeling for low flow velocities in the turbulent flow regime.

  1. Genetic diversity of giant clams (Tridacna spp.) and their associated Symbiodinium in the central Red Sea

    KAUST Repository

    Pappas, Melissa

    2017-05-19

    The biodiversity of the Red Sea remains relatively understudied, particularly for invertebrate taxa. Documenting present patterns of biodiversity is essential for better understanding Red Sea reef ecosystems and how these ecosystems may be impacted by stressors (such as fishing and climate change). Several species of giant clams (genus Tridacna) are reported from the Red Sea, although the majority of research effort has occurred in the Gulf of Aqaba. We investigated the genetic diversity (16S rDNA) of the Tridacna species found in the central Saudi Arabian Red Sea. We also investigated the genetic diversity (ITS rDNA) of symbiotic dinoflagellates Symbiodinium associated with these clams. Samples were collected from nine reefs on a cross-shelf gradient near Thuwal, Saudi Arabia. Two species, T. squamosa and T. maxima, were recorded, with the latter being the most abundant. Tridacna squamosina, a species recently reported in the northern Red Sea, was not found, suggesting that this species is not present or is very rare in our study region. All tridacnids sampled were found to harbor Symbiodinium grouped in Clade A, considered an opportunistic, heat-tolerant symbiont group in anemones and corals. The consistent association with Clade A Symbiodinium in central Red Sea tridacnids may reflect the consequence of adaptation to the relatively extreme conditions of the Red Sea. This study contributes to an ever-growing catalog of Red Sea biodiversity and serves as important baseline information for a region experiencing dynamic pressures.

  2. Microstructure and mechanical properties of the TIG welded joints of fusion CLAM steel

    Energy Technology Data Exchange (ETDEWEB)

    Jiang Zhizhong, E-mail: zhizhongjiang2006@yahoo.com.c [School of Materials Science and Engineering, University of Science and Technology Beijing, Xueyuan Road, Beijing 100083 (China); Ren Litian; Huang Jihua; Ju Xin; Wu Huibin [School of Materials Science and Engineering, University of Science and Technology Beijing, Xueyuan Road, Beijing 100083 (China); Huang Qunying; Wu Yican [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China)

    2010-12-15

    The CLAM steel plates were butt-welded through manual tungsten inert gas welding (TIG) process, and the following post-welding heat treatment (PWHT) at 740 {sup o}C for 1 h. The microstructure and mechanical properties of the welded joints were measured. The results show that both hardening and softening occur in the weld joints before PWHT, but the hardening is not removed completely in the weld metal and the fusion zone after PWHT. In as-welded condition, the microstructure of the weld metal is coarse lath martensite, and softened zone in heat-affected zone (HAZ) consists of a mixture of tempered martensite and ferrite. After PWHT, a lot of carbides precipitate at all zones in weld joints. The microstructure of softened zone transforms to tempered sorbite. Tensile strength of the weld metal is higher than that of HAZ and base metal regardless of PWHT. However, the weld metal has poor toughness without PWHT. The impact energy of the weld metal after PWHT reaches almost the same level as the base metal. So it is concluded that microstructure and mechanical properties of the CLAM steel welded joints can be improved by a reasonable PWHT.

  3. Population dynamics of the freshwater clam Galatea paradoxa from the Volta River, Ghana

    Directory of Open Access Journals (Sweden)

    Adjei-Boateng D.

    2012-07-01

    Full Text Available Population parameters such as asymptotic (L∞, growth coefficient (K, mortality rates (Z,F and M, exploitation level (E and recruitment pattern of the freshwater clam Galatea paradoxa were estimated using length-frequency data from the Volta River estuary, Ghana. The L∞ for G. paradoxa at the Volta estuary was 105.7 mm, the growth coefficient (K and the growth performance index (Ǿ ranged between 0.14–0.18 year-1 and 3.108–3.192, respectively. Total mortality (Z was 0.65–0.82 year-1, while natural mortality (M and fishing mortality (F were 0.35–0.44 year-1 and 0.21–0.47 year-1, respectively, with an exploitation level of 0.32–0.57. The recruitment pattern suggested that G. paradoxa has year-round recruitment with a single pulse over an extended period (October–March in the Volta River. The Volta River stock of G. paradoxa is overfished and requires immediate action to conserve it. This can be achieved by implementing a minimum landing size restriction and intensifying the culture of smaller clams which is a traditional activity at the estuary.

  4. Clams sensitivity towards As and Hg: A comprehensive assessment of native and exotic species.

    Science.gov (United States)

    Velez, Cátia; Freitas, Rosa; Antunes, Sara C; Soares, Amadeu M V M; Figueira, Etelvina

    2016-03-01

    To assess the environmental impact of As and Hg, bioindicator organisms such as bivalves have been used. Nevertheless, few studies have assessed the impacts of As and Hg in Ruditapes decussatus and Ruditapes philippinarum, which are native and exotic species in Europe, respectively. The main goal of the present study was to assess elements' partitioning and detoxification strategies of R. decussatus and R. philippinarum. Both clams showed a higher capacity to bioconcentrate Hg (BCF 2.29-7.49), when compared to As (0.59-1.09). Furthermore, As accumulation in both species was similar in the soluble and insoluble fractions, while in both species the majority of Hg was found in the insoluble fraction. Clams exposed to As showed different detoxification strategies, since R. decussatus had higher ability to enhance antioxidant enzymes and metallothioneins in order to reduce toxicity, and R.philippinarum increased glutathione S-transferase Ω activity, that catalyzes monomethyl arsenate reduction, the rate-limiting reaction in arsenic biotransformation. When exposed to Hg, R. decussatus presented, higher synthesis of antioxidant enzymes and lower LPO, being able to better tolerate Hg than the exotic species R. philippinarum. Thus under relevant levels of As and Hg contamination our work evidenced the higher ability of R. decussatus to survive and inhabit coastal environments not heavily contaminated by Hg and As. Copyright © 2015 Elsevier Inc. All rights reserved.

  5. Genetic diversity of giant clams (Tridacna spp.) and their associated Symbiodinium in the central Red Sea

    KAUST Repository

    Pappas, Melissa; He, Song; Hardenstine, Royale; Kanee, Hana; Berumen, Michael L.

    2017-01-01

    The biodiversity of the Red Sea remains relatively understudied, particularly for invertebrate taxa. Documenting present patterns of biodiversity is essential for better understanding Red Sea reef ecosystems and how these ecosystems may be impacted by stressors (such as fishing and climate change). Several species of giant clams (genus Tridacna) are reported from the Red Sea, although the majority of research effort has occurred in the Gulf of Aqaba. We investigated the genetic diversity (16S rDNA) of the Tridacna species found in the central Saudi Arabian Red Sea. We also investigated the genetic diversity (ITS rDNA) of symbiotic dinoflagellates Symbiodinium associated with these clams. Samples were collected from nine reefs on a cross-shelf gradient near Thuwal, Saudi Arabia. Two species, T. squamosa and T. maxima, were recorded, with the latter being the most abundant. Tridacna squamosina, a species recently reported in the northern Red Sea, was not found, suggesting that this species is not present or is very rare in our study region. All tridacnids sampled were found to harbor Symbiodinium grouped in Clade A, considered an opportunistic, heat-tolerant symbiont group in anemones and corals. The consistent association with Clade A Symbiodinium in central Red Sea tridacnids may reflect the consequence of adaptation to the relatively extreme conditions of the Red Sea. This study contributes to an ever-growing catalog of Red Sea biodiversity and serves as important baseline information for a region experiencing dynamic pressures.

  6. Overview on the welding technologies of CLAM steel and the DFLL TBM fabrication

    Directory of Open Access Journals (Sweden)

    Junyu Zhang

    2016-12-01

    Full Text Available Dual Functional Lithium Lead (DFLL blanket was proposed for its advantages of high energy exchange efficiency and on-line tritium extraction, and it was selected as the candidate test blanket module (TBM for China Fusion Engineering Test Reactor (CFETR and the blanket for Fusion Design Study (FDS series fusion reactors. Considering the influence of high energy fusion neutron irradiation and high heat flux thermal load on the blanket, China Low Activation Martensitic (CLAM steel was selected as the structural material for DFLL blanket. The structure of the blanket and the cooling internal components were pretty complicated. Meanwhile, high precision and reliability were required in the blanket fabrication. Therefore, several welding techniques, such as hot isostatic pressing diffusion bonding, tungsten inner gas welding, electron beam welding and laser beam welding were developed for the fabrication of cooling internals and the assembly of the blanket. In this work, the weldability on CLAM steel by different welding methods and the properties of as-welded and post-weld heat-treated joints were investigated. Meanwhile, the welding schemes and the assembly strategy for TBM fabrication were raised. Many tests and research efforts on scheme feasibility, process standardization, component qualification and blanket assembly were reviewed.

  7. Two new miniature inverted-repeat transposable elements in the genome of the clam Donax trunculus.

    Science.gov (United States)

    Šatović, Eva; Plohl, Miroslav

    2017-10-01

    Repetitive sequences are important components of eukaryotic genomes that drive their evolution. Among them are different types of mobile elements that share the ability to spread throughout the genome and form interspersed repeats. To broaden the generally scarce knowledge on bivalves at the genome level, in the clam Donax trunculus we described two new non-autonomous DNA transposons, miniature inverted-repeat transposable elements (MITEs), named DTC M1 and DTC M2. Like other MITEs, they are characterized by their small size, their A + T richness, and the presence of terminal inverted repeats (TIRs). DTC M1 and DTC M2 are 261 and 286 bp long, respectively, and in addition to TIRs, both of them contain a long imperfect palindrome sequence in their central parts. These elements are present in complete and truncated versions within the genome of the clam D. trunculus. The two new MITEs share only structural similarity, but lack any nucleotide sequence similarity to each other. In a search for related elements in databases, blast search revealed within the Crassostrea gigas genome a larger element sharing sequence similarity only to DTC M1 in its TIR sequences. The lack of sequence similarity with any previously published mobile elements indicates that DTC M1 and DTC M2 elements may be unique to D. trunculus.

  8. Fishery of the short-necked clam Paphia undulata in Southern Negros Occidental, Central Philippines

    Directory of Open Access Journals (Sweden)

    Karen A. Villarta

    2010-06-01

    Full Text Available This study documents the fishery of the short-necked clam Paphia undulata in coastal waters of southern Negros Occidental. Catch and effort estimates were determined based on daily records of compressor divers gathered between February-July 2008 in Himamaylan City and July 2008-May 2009 in the town of Hinigaran. Fishing and marketing practices in both areas were also documented and population biology information noted.Compared to earlier conditions, present fishing patterns show a worsened stage of overexploitation primarily characterized by collection of predominantly small and immature (mostly <45 mm shell lengths sizes. Intensity/duration and location of fishing also varied due to both abundance and demand factors.The difference in sizes of clams and the varying fishing durations in each area suggest a non-uniform pattern of settlement resulting most likely from differential larval recruitment, the likely factors causing the local boom and bust fishery. The larger and long term extent of the effect of these factors can only be further investigated by parallel 2-3 year fishery-dependent and -independent surveys

  9. Comparison of Tension-free Vaginal Tape Versus Transobturator Tape in Women with Stress Urinary Incontinence

    Directory of Open Access Journals (Sweden)

    Zinat Ghanbari

    2007-06-01

    Full Text Available Objective: This study compared the Tension-free vaginal tape (TVT and Transobturator tape (TOT procedures for surgical treatment of stress urinary incontinence in women.Materials and methods: This prospective non randomized clinical trial was conducted in Vali-e-asr hospital from March 2001 to March 2005. A total of 71 patients with clinical and urodynamic diagnosis of Stress urinary incontinence (SUI were enrolled in the study. Patients were divided into two groups and underwent TVT or TOT procedures. Mean operation time, cure rate, post operative urinary retention, bleeding and infection were compared between two groups. SPSS software was used for statistical analysis. Chi square and fisher exact test calculated the effects of the nominal variables. Mean difference of quantitative variables were compared by student's T- test. P ≤0.05 was considered statistically significant. Results: There was no significant difference in mean time of operation and peri-operative complications among groups. Urinary retention was 13.8% (n=5 in the TVT group versus 2.8% (n=1 in TOT group (NS. The rates of cure (91.6% vs 91.4%, improvement (5.6% vs 8.6% and failure (2.8% vs 0 were similar for the TVT and TOT groups. The rate of hemorrhagic complications was 5.5% in TVT and 2.8% in TOT group (NS.Conclusion: TOT appears to be equally efficient to TVT for surgical treatment of stress urinary incontinence after 30 months follow-up.

  10. Three-dimensional modelling of metal evaporated tape

    International Nuclear Information System (INIS)

    Kay, G.E.

    1999-06-01

    As developments in magnetic recording increase, the demands for high density recording media continue to rise. One particular medium developed towards meeting these needs is the commercially successful metal evaporated (ME) tape. To provide a deeper understanding of the magnetic processes occurring in recording media, theoretical studies are carried out to complement experimental observations. Therefore, this thesis is concerned with developing a micromagnetic model to simulate the magnetic behaviour of ME tape. ME tape consists of bundles of granular columns which are tilted towards the film normal. The morphology of the film influences the magnetic behaviour and a 3D model is developed in this thesis to represent the columnar structure and the granular nature of ME tape. A Monte Carlo algorithm, consisting of a 'move and grow' procedure, is developed to generate an irregular system of spherical grains whose radii were generated from a log-normal distribution. This structure provides the foundation for modelling columns of ME tape. Initially an isolated column of ME tape was investigated. Grains were considered to be single domain and the dynamic process of the magnetic moments was explored by the Landau-Lifschitz equation. The model demonstrated that as the strength of the exchange coupling parameter increased, then moments which were strongly coupled resisted large negative fields and square hysteresis loops with a high coercivity were produced. Reversal of the moments was observed to be initiated at the ends of a column and then propagated throughout the column. This was attributed to large demagnetising fields and was particularly evident in the model with aligned easy axes. If the easy axes were randomly orientated then more disorder was present in the model and moments rotated incoherently. This produced hysteresis loops that were less square than those of the aligned model. The results also showed how the microstructure influenced the reversal processes

  11. Dynamic response of HTS composite tapes to pulsed currents

    International Nuclear Information System (INIS)

    Meerovich, V; Sokolovsky, V; Prigozhin, L; Rozman, D

    2006-01-01

    Dynamic voltage-current characteristics of an HTS Ag/BiSCCO composite tape are studied both experimentally and theoretically. The tape is subjected to pulsed currents with different shapes and magnitudes and voltage traces are measured using the four-point method with different locations of potential taps on the sample surface. Clockwise and anticlockwise hysteresis loops are obtained for the same sample depending on the location of the potential taps. The dynamic characteristics deviate substantially from the DC characteristic, especially in the range of low voltages where a criterion for the critical current value is usually chosen (1-10 μV cm -1 ). The critical current determined from dynamic characteristics and its change with the pulse magnitude depend on the location of the potential taps and on the curve branch chosen for the critical current determination (ascending or descending). The theoretical analysis is based on a model of the magnetic flux diffusion into a composite tape for a superconductor described by the flux creep characteristic. Numerical simulation based on this model gives results in good agreement with the experimental ones and explains the observed peculiarities of the dynamic characteristics of HTS composite tapes. The difference between the magnetic diffusion into a tape and a slab is discussed

  12. A quantitative estimation of the energetic cost of brown ring disease in the Manila clam using Dynamic Energy Budget theory.

    NARCIS (Netherlands)

    Flye Sainte Marie, J.G.; Jean, F.; Paillard, C.; Kooijman, S.A.L.M.

    2009-01-01

    Brown ring disease (BRD) in the Manila clam, Ruditapes philippinarum, is a bacterial disease caused by the pathogen Vibrio tapetis. This disease induces the formation of a characteristic brown conchiolin deposit on the inner shell and is associated with a decrease in condition index indicating that

  13. PARTICLE REMOVAL RATES BY THE MUD SHRIMP UPOGEBIA PUGETTENSIS, ITS BURROW, AND A COMMENSAL CLAM: EFFECTS ON ESTUARINE PHYTOPLANKTON ABUNDANCE

    Science.gov (United States)

    The burrowing shrimp Upogebia pugettensis is an abundant intertidal inhabitant of Pacific Northwest bays and estuaries where it lives commensally with the bivalve Cryptomya californica. Suspension-feeding activities by the shrimp and by its commensal clam, as well as particle se...

  14. Biomarker responses and contamination levels in the clam Ruditapes philippinarum for biomonitoring the Lagoon of Venice (Italy).

    Science.gov (United States)

    Matozzo, Valerio; Binelli, Andrea; Parolini, Marco; Locatello, Lisa; Marin, Maria Gabriella

    2010-03-01

    A multibiomarker approach was used to assess effects of environmental contaminants in the clam Ruditapes philippinarum from the Lagoon of Venice. Bivalves were collected in 8 sites of the Lagoon (Campalto, Marghera, Palude del Monte, Valle di Brenta, Cà Roman, San Servolo, Fusina and Canale Dese), differently influenced by both anthropogenic impact and natural conditions. The following biomarkers were chosen: total haemocyte count and lysozyme activity in cell-free haemolymph as immunomarkers, acetylcholinesterase activity in gills as a biomarker of exposure to neurotoxic compounds, vitellogenin-like protein levels in both digestive gland and cell-free haemolymph as a biomarker of exposure to estrogenic compounds, and survival-in-air widely used to evaluate general stress conditions in clams. In addition, polychlorinated biphenyls (PCBs), polycyclic aromatic hydrocarbons (PAHs), 1,1,1-Trichloro-2,2-bis(p-chlorophenyl)ethane (p,p'-DDT) and its breakdown products (DDE, DDD), hexachlorobenzene (HCB) and hexachlorocyclohexane (HCH) were measured in clams. Results demonstrated that the integrated approach between biomarkers and chemical analyses in R. philippinarum is a useful tool in biomonitoring the Lagoon of Venice. The biomarker responses suggested quite similar contamination levels in the entire Lagoon, although the relative impact of differing classes of pollutants changed among sites according to potential sources, as chemical analyses demonstrated. Overall, among the sampling sites investigated, Palude del Monte can represent an environmental risk area, bearing in mind its peculiar use for clam culture.

  15. Species Profiles: Life Histories and Environmental Requirements of Coastal Fishes and Invertebrates (Pacific Southwest). Common Littleneck Clam.

    Science.gov (United States)

    1986-04-01

    cells in clam (P. tenerrima) in having December and January (Quayle 1943). w , , radiating ribs more prominent than The growth of gametes reaches a...reproductive cycle levels in intertidal mollusks of of Protothaca stamine ’ using histo- California. Veliger 14(4):365-372. logical, wet weight-dry

  16. Radio-resistance of some bacterial pathogens in soft-shell clams (Mya arenaria) and mussels (Mytilus edulis)

    International Nuclear Information System (INIS)

    Licciardello, J.J.; D'Entremont, D.L.; Lundstrom, R.C.

    1989-01-01

    Gamma-irradiation decimal reduction doses were determined for E. coli, Salmonella typhimurium, Shigella flexneri, Strept. faecalis, Staph, aureus, and the Total Plate Count in a soft-shell clam or mussel substrate. Factors to be considered for designing and irradiation bacterial-decontamination process for shellfish are discussed

  17. Bidirectional recording performance of a perpendicular evaporated Co-CoO tape

    Energy Technology Data Exchange (ETDEWEB)

    Motohashi, K. [Sony Corporation, 3-4-1 Sakuragi, Tagajo-shi, Miyagi 985-0842 (Japan)], E-mail: Kazunari.Motohashi@jp.sony.com; Ikeda, N.; Sato, T.; Shiga, D.; Ono, H.; Onodera, S. [Sony Corporation, 3-4-1 Sakuragi, Tagajo-shi, Miyagi 985-0842 (Japan)

    2008-11-15

    It is the first report on the recording performance of a perpendicular metal evaporated (ME) tape measured with a giant magnetoresistive head. To solve the application difficulty of oblique evaporated tape media to linear scan tape systems, a perpendicular evaporated Co-CoO tape was proposed instead. The prepared sample showed perpendicular anisotropy with coercivity of 107.3 kA/m, M{sub r}t of 3.9 mA and squareness of 0.25. Identical recording characteristics were obtained for both head-media moving directions, which enables the application of perpendicular evaporated Co-CoO tape to linear scan tape systems. The better carrier-to-noise ratio was also confirmed by comparison with a current advanced product of metal particulate tape, which can realize the higher recording density of linear scan tape systems using ME tape.

  18. Bidirectional recording performance of a perpendicular evaporated Co-CoO tape

    International Nuclear Information System (INIS)

    Motohashi, K.; Ikeda, N.; Sato, T.; Shiga, D.; Ono, H.; Onodera, S.

    2008-01-01

    It is the first report on the recording performance of a perpendicular metal evaporated (ME) tape measured with a giant magnetoresistive head. To solve the application difficulty of oblique evaporated tape media to linear scan tape systems, a perpendicular evaporated Co-CoO tape was proposed instead. The prepared sample showed perpendicular anisotropy with coercivity of 107.3 kA/m, M r t of 3.9 mA and squareness of 0.25. Identical recording characteristics were obtained for both head-media moving directions, which enables the application of perpendicular evaporated Co-CoO tape to linear scan tape systems. The better carrier-to-noise ratio was also confirmed by comparison with a current advanced product of metal particulate tape, which can realize the higher recording density of linear scan tape systems using ME tape

  19. Intra-specific diet shift in manila clams (Ruditapes philippinarum) as revealed by carbon and nitrogen stable isotopes and fatty acid biomarker

    Science.gov (United States)

    Suh, Y.; Shin, K.

    2011-12-01

    Manila clams sampled in Seonjae Island, Korea with shell lengths (SL) below 19.76 mm in average showed a significantly depleted carbon and nitrogen isotope values (Pcultured in IFHRI. The result of fatty acid composition of manila clams in relation to size or growth rate suggests that fast growing clams would have rapid metabolism of fatty acids not required by the animals and an accumulation of the essential fatty acids (PUFA). In addition, their higher energy requirement and more active state of development would further diminish lipid reserve of the species.

  20. Stick-slip substructure in rapid tape peeling

    KAUST Repository

    Thoroddsen, Sigurdur T.

    2010-10-15

    The peeling of adhesive tape is known to proceed with a stick-slip mechanism and produces a characteristic ripping sound. The peeling also produces light and when peeled in a vacuum, even X-rays have been observed, whose emissions are correlated with the slip events. Here we present direct imaging of the detachment zone when Scotch tape is peeled off at high speed from a solid surface, revealing a highly regular substructure, during the slip phase. The typical 4-mm-long slip region has a regular substructure of transverse 220 μm wide slip bands, which fracture sideways at speeds over 300 m/s. The fracture tip emits waves into the detached section of the tape at ∼100 m/s, which promotes the sound, so characteristic of this phenomenon.

  1. Experimental Investigations of Woven Textile Tape as Strain Sensor

    Science.gov (United States)

    Kannaian, T.; Naveen, V. S.; Muthukumar, N.; Thilagavathi, G.

    2015-10-01

    In this article, a strain sensitive textile based elastomeric tape sensor has been developed and process parameters for sensor development are optimized. Polyester yarns are used as base threads and rubber threads are used as elastomer for the sensor development. The sensor has been developed with the help of narrow width tape loom by introducing the silver coated nylon yarn in the middle of the tape structure. The influence of weave structure, number of conductive threads and rubber thread tension on sensor development has been optimized by using the Box-Behnken method and the results are analyzed using the Design expert software. From the results, it is found that six numbers of conductive threads in a plain weave structure with rubber thread tension of 750 g is suitable for the sensor to give high gauge factor of 1.626.

  2. Stick-slip substructure in rapid tape peeling

    KAUST Repository

    Thoroddsen, Sigurdur T; Nguyen, H. D.; Takehara, K.; Etoh, T. G.

    2010-01-01

    The peeling of adhesive tape is known to proceed with a stick-slip mechanism and produces a characteristic ripping sound. The peeling also produces light and when peeled in a vacuum, even X-rays have been observed, whose emissions are correlated with the slip events. Here we present direct imaging of the detachment zone when Scotch tape is peeled off at high speed from a solid surface, revealing a highly regular substructure, during the slip phase. The typical 4-mm-long slip region has a regular substructure of transverse 220 μm wide slip bands, which fracture sideways at speeds over 300 m/s. The fracture tip emits waves into the detached section of the tape at ∼100 m/s, which promotes the sound, so characteristic of this phenomenon.

  3. Age-of-Air, Tape Recorder, and Vertical Transport Schemes

    Science.gov (United States)

    Lin, S.-J.; Einaudi, Franco (Technical Monitor)

    2000-01-01

    A numerical-analytic investigation of the impacts of vertical transport schemes on the model simulated age-of-air and the so-called 'tape recorder' will be presented using an idealized 1-D column transport model as well as a more realistic 3-D dynamical model. By comparing to the 'exact' solutions of 'age-of-air' and the 'tape recorder' obtainable in the 1-D setting, useful insight is gained on the impacts of numerical diffusion and dispersion of numerical schemes used in global models. Advantages and disadvantages of Eulerian, semi-Lagrangian, and Lagrangian transport schemes will be discussed. Vertical resolution requirement for numerical schemes as well as observing systems for capturing the fine details of the 'tape recorder' or any upward propagating wave-like structures can potentially be derived from the 1-D analytic model.

  4. Prevalence and Density of Digenetic Trematode Metacercariae in Clams and Oysters from Western Coastal Regions of the Republic of Korea.

    Science.gov (United States)

    Sohn, Woon-Mok; Na, Byoung-Kuk; Cho, Shin-Hyeong; Lee, Won-Ja

    2017-08-01

    A survey was performed to know the recent infection status of digenetic trematode metacercariae in clams and oysters from 4 sites in western coastal regions of the Republic of Korea (=Korea). Four species of clams (Mactra veneriformis, Ruditapes philippinarum, Cyclina sinensis, and Saxidomus purpuratus) were collected from Taean-gun, Chungcheongnam-do (Province), Buan-gun (County) and Gochang-gun, Jeollabuk-do, and oysters, Crassostrea gigas, from Shinan-gun, Jeollanam-do were transferred to our laboratory on ice and examined by the artificial digestion method. The metacercariae of Himasthla alincia were detected in 3 species of clams, M. veneriformis, R. philippinarum, and C. sinensis from the 3 surveyed areas. The positive rate and the mean density per clam infected were 98.9% (30.8 metacercariae) in M. veneriformis, 60.0% (5.0) in R. philippinarum, and 96.0% (28.4) in C. sinensis. The positive rate (mean density) of Acanthoparyphium tyosenense metacercariae in M. veneriformis was 50.0% (2.1) from Taean-gun and 70.0% (2.8) from Gochang-gun. The metacercariae of Parvatrema spp. were detected in M. veneriformis and R. philippinarum from Taean-gun and Gochang-gun; the positive rate (mean density) was 63.3% (4,123) and 50.0% (19) in M. veneriformis, and 6.7% (126) and 100% (238) in R. philippinarum from the 2 regions, respectively. The metacercariae of Gymnophalloides seoi were detected in all 30 oysters from Shinan-gun, and their average density per oyster was 646. From the above results, it has been confirmed that more than 3 species of metacercariae are prevalent in clams from the western coastal regions, and G. seoi metacercariae are still prevalent in oysters from Shinan-gun, Jeollanam-do, Korea.

  5. Mirror-Touch and Ticker Tape Perceptions in Synesthesia

    Directory of Open Access Journals (Sweden)

    Charlotte Anne Chun

    2013-11-01

    Full Text Available A fundamental question in the field of synesthesia is whether it is associated with other cognitive phenomena. The current study examined synesthesia’s connections with phenomenal traits of mirror-touch and ticker tape experiences, as well as the representation of the three phenomena in the population, across gender and domain of work/study. Mirror-touch is the automatic, involuntary experience of tactile sensation on one's own body when others are being touched. For example, seeing another person’s arm being stroked can evoke physical touch sensation on one’s own arm. Ticker tape is the automatic visualization of spoken words or thoughts, such as a teleprompter. For example, when spoken to, a ticker taper might see mentally the spoken words displayed in front of his face or as coming out of the speaker’s mouth. To explore synesthesia’s associations with these phenomena, a diverse group (n=3,743 was systematically recruited from eight universities and one public museum in France to complete an online screening. Of the 1,017 eligible respondents, synesthetes (across all subtypes reported higher rates of mirror-touch and ticker tape than non-synesthetes, suggesting that synesthesia is associated with these phenomenal traits. However effect size was small and we could not rule out that response bias influenced these associations. Mirror-touch and ticker tape were independent. No differences were found across gender or domain of work and study in prevalence of synesthesia, mirror-touch or ticker tape. The prevalence of ticker tape, unknown so far, was estimated at about 7%, an intermediate rate between estimates of grapheme-color (2 to 4% and sequence-space synesthesia (9 to 14%. Within synesthesia, grapheme-personification, also called ordinal-linguistic personification was the most common subtype and was estimated around 12%. Co-occurences of the different types of synesthesia were higher than chance, though at the level of small effect

  6. Percolation modelling for highly aligned polycrystalline superconducting tapes

    Energy Technology Data Exchange (ETDEWEB)

    Rutter, N A; Glowacki, B A; Evetts, J E [Department of Materials Science and Metallurgy, University of Cambridge, Pembroke Street, Cambridge CB2 3QZ (United Kingdom); IRC in Superconductivity, Madingley Road, Cambridge CB3 0HE (United Kingdom)

    2000-11-01

    Surface and bulk texture measurements have been carried out on highly aligned NiFe tapes, suitable for use as coated conductor substrates. Data from small-area electron backscatter diffraction measurements are compared with those from bulk x-ray analysis in the development of a two-dimensional percolation model, and the two are shown to give very similar results. No evidence of grain-to-grain correlation is found. The model is then developed to assess how the properties of a superconducting layer grown epitaxially on buffered tapes will depend on parameters such as sample size, grain size and the extent of grain alignment. (author)

  7. Patient goals after tension free vaginal tape operation

    DEFF Research Database (Denmark)

    Glavind, Karin; Bjørk, Jonna; Kousgaard, Sabrina Just

    INTRODUCTION: This prospective study investigates sexual function in women after a tension-free vaginal tape (TVT) operation and compares short-term and long-term effects. METHODS: Sixty-three women had a TVT operation performed at Aalborg University Hospital, Department of Gynecology and Obstetr......INTRODUCTION: This prospective study investigates sexual function in women after a tension-free vaginal tape (TVT) operation and compares short-term and long-term effects. METHODS: Sixty-three women had a TVT operation performed at Aalborg University Hospital, Department of Gynecology...

  8. The new CERN tape software - getting ready for total performance

    CERN Document Server

    Cano, E; Kruse, D F; Kotlyar, V; Côme, D

    2015-01-01

    CASTOR (the CERN Advanced STORage system) is used to store the custodial copy of all of the physics data collected from the CERN experiments, both past and present. CASTOR is a hierarchical storage management system that has a disk-based front-end and a tape-based back-end. The software responsible for controlling the tape back-end has been redesigned and redeveloped over the last year and was put in production at the beginning of 2015. This paper summarises the motives behind the redesign, describes in detail the redevelopment work and concludes with the short and long-term benefits.

  9. Properties of hot pressed MgB2/Ti tapes

    International Nuclear Information System (INIS)

    Kovac, P.; Husek, I.; Melisek, T.; Fedor, J.; Cambel, V.; Morawski, A.; Kario, A.

    2009-01-01

    Hot axial and hot isostatic pressing was applied for single-core MgB 2 /Ti tapes. Differences in transport current density, n-exponents and critical current anisotropy are discussed and related to the grain connectivity influenced by pressing. The magnetic Hall probe scanning measurements allowed observing the isolated regions for axially hot pressed sample attributed to the longitudinally oriented cracks introduced by pressing. The highest current densities were measured for the tape subjected to hot isostatic pressing due to improved connectivity.

  10. New concept for a compact tape transport system

    International Nuclear Information System (INIS)

    Mlekodaj, R.L.; Zganjar, E.F.; Cole, J.D.

    1980-01-01

    A new concept in tape transport systems for the collection and counting of radioactive samples from an on-line isotope separator has been developed. This new compact design was motivated by space limitations but important additional improvements over previous designs were made in cost, simplicity and vacuum quality. The system is based on a continuous loop of 6.5 millimeter wide recording tape 116 meters long with a conducting coating on one side for beam current monitoring. One small stepping motor is required for operation

  11. A new concept for a compact tape transport system

    International Nuclear Information System (INIS)

    Mlekodaj, R.L.; Zganjar, E.F.; Cole, J.D.

    1981-01-01

    A new concept in tape transport systems for the collection and counting of radioactive samples from an on-line isotope separator has been developed. This new compact design was motivated by space limitations but important additional improvements over previous designs were made in cost, simplicity and vacuum quality. The system is based on a continuous loop of 6.5 mm wide recording tape 116 m long with a conducting coating on one side for beam current monitoring. One small stepping motor is required for operation. (orig.)

  12. Delamination behaviour in differently copper laminated REBCO coated conductor tapes under transverse loading

    Energy Technology Data Exchange (ETDEWEB)

    Gorospe, Alking [Department of Mechanical Design Engineering, Andong National University, 1375 Kyungdong-Ro, Andong 760-749 (Korea, Republic of); Department of Engineering, Aurora State College of Technology, Baler Aurora 3200 (Philippines); Nisay, Arman [Department of Mechanical Design Engineering, Andong National University, 1375 Kyungdong-Ro, Andong 760-749 (Korea, Republic of); Shin, Hyung-Seop, E-mail: hsshin@andong.ac.kr [Department of Mechanical Design Engineering, Andong National University, 1375 Kyungdong-Ro, Andong 760-749 (Korea, Republic of)

    2014-09-15

    Highlights: • I{sub c} degradation behavior under transverse tension loading in different CC tape structure. • Weibull distribution analysis applied on delamination mechanism of CC tape. • Delamination mechanism on CC tapes depending on copper lamination type. • SEM and WDS mapping analysis of delamination sites under transverse loading. - Abstract: Laminated HTS coated conductor (CC) tapes having a unique multi-layer structure made them vulnerable when exposed to transverse loading. Electromechanical transport properties of these CC tapes can be affected by excessive transverse stresses. Due to the coefficient of thermal expansion (CTE) mismatch and incompatibility among constituent materials used in coil applications, delamination among layers occurs and causes critical current, I{sub c} degradation in the CC tapes. In this study, the delamination behaviors in copper (Cu) solder-laminated CC tapes by soldering and surround Cu-stabilized ones by electroplating under transverse tension loading were investigated. Similarly to the surround Cu-stabilized CC tapes in our previous reports, the Cu solder-laminated CC tapes also showed an abrupt and gradual I{sub c} degradation behavior. However, the Cu solder-laminated CC tapes showed different delamination morphologies as compared to the surround Cu-stabilized CC tapes; the superconducting side and the substrate side of the Cu solder laminated CC tapes were totally separated by delamination. On the other hand, the brass laminate did not show any significant effect on the delamination strength when it is added upon the surround Cu-stabilized CC tapes.

  13. Clam wave energy converter. Report for period July 1979 to December 1980

    Energy Technology Data Exchange (ETDEWEB)

    1981-02-01

    Work by the Sea Energy Asociates Ltd - Lanchester Polytechnic Wave Energy Group on the Clam device since the April 1979 feasibility study has shown it to be a well developed and viable device capable of extracting energy economically from sea waves. The experience of the team includes mooring, structural and device tests from 1/100th to 1/10th scale in narrow and wide tanks, Draycote Reservoir and on Loch Ness. Theoretical and semi-empirical modelling has become increasingly important. Recently a test rig to assess a 1/10th scale power take off system, based on a Wells turbine, has been completed. The philosophy of the project team has been to aim for a device as simple as possible, with a small number of moving parts in order to minimise maintenance problems.

  14. Comparative Study of the Accumulation of Ni in Different Tissues of Mussels and Soft Clams

    Directory of Open Access Journals (Sweden)

    Chalkiadakis O.

    2013-04-01

    Full Text Available Two bivalves, the mussel Mytilus galloprovincialis, and the soft clam Callista chione were exposed to various Ni concentrations for a total period of 20 days, and then a depuration period of 10 days followed. Nickel accumulation in gills, mantle and the remaining body of the animals was measured after 5, 10, 15 and 20 days of exposure to Ni-contaminated seawater. The two organisms showed different behavior regarding Ni accumulation in all three tissues examined. In all concentrations, Ni accumulation increased with time in all three tissues of Mytilus galloprovincialis with gills being the most effective accumulator per dry mass. On the other hand, Callista chione showed an initial response to Ni contamination the first 5 days, followed by stabilization or even a slight decrease of Ni accumulation.

  15. Combined proteomic and metallomic analyses in Scrobicularia plana clams to assess environmental pollution of estuarine ecosystems.

    Science.gov (United States)

    González-Domínguez, Raúl; Santos, Hugo Miguel; Bebianno, Maria João; García-Barrera, Tamara; Gómez-Ariza, José Luis; Capelo, José Luis

    2016-12-15

    Estuaries are very important ecosystems with great ecological and economic value, but usually highly impacted by anthropogenic pressure. Thus, the assessment of pollution levels in these habitats is critical in order to evaluate their environmental quality. In this work, we combined complementary metallomic and proteomic approaches with the aim to monitor the effects of environmental pollution on Scrobicularia plana clams captured in three estuarine systems from the south coast of Portugal; Arade estuary, Ria Formosa and Guadiana estuary. Multi-elemental profiling of digestive glands was carried out to evaluate the differential pollution levels in the three study areas. Then, proteomic analysis by means of two-dimensional gel electrophoresis and mass spectrometry revealed twenty-one differential proteins, which could be associated with multiple toxicological mechanisms induced in environmentally stressed organisms. Accordingly, it could be concluded that the combination of different omic approaches presents a great potential in environmental research. Copyright © 2016 Elsevier Ltd. All rights reserved.

  16. Use of antioxidant enzymes of clam Ruditapes philippinarum as biomarker to polycyclic aromatic hydrocarbon pollution

    Science.gov (United States)

    Zhu, Lin; Tang, Xuexi; Wang, Ying; Sui, Yadong; Xiao, Hui

    2016-03-01

    The typical organic pollutant polycyclic aromatic hydrocarbon (PAH) anthracene was selected as a contaminant to investigate its effects on the activities of superoxide dismutase (SOD), catalase (CAT) and glutathione peroxidase (GSH-Px) in the clam Ruditapes philippinarum. The results show that SOD, CAT and GSH-Px had diff erent induction and inhibition reactions to anthracene stress, and that three diff erent organs in R. philippinarum (visceral mass, muscle tissue and mantle) had diff erent sensitivities to anthracene stress. This study suggest that SOD activities of the visceral mass, CAT activitities of the mantle and the visceral mass, and GSH-Px activity of the muscle tissue could be used as sensitive indicators of anthracene stress in R. philippinarum.

  17. Parasites of the hard clam Meretrix meretrix Linnaeus from Western Johor Straits, Malaysian

    Science.gov (United States)

    Azmi, Nur Fauzana; Ghaffar, Mazlan Abd.; Cob, Zaidi Che

    2014-09-01

    This study describes the apicomplexa as well as other parasites infecting organs/tissues of the hard clam Meretrix meretrix Linnaeus, from Merambong Shoal, Western Johor Straits, Malaysia. Samples were collected randomly by hand picking, in November and December 2013. Histological techniques were performed, stained using Masson's Trichrome protocol and observed under light microscope. The results showed that gonad and gill were the most infected organs followed by digestive gland, intestine and adductor muscle. No pathology condition was observed in the mantle. Histophatological examination showed that the gregarine, Nematopsis, unidentified coccidian and Perkinsus were found in the gill and gonad, and also in the numerous hemocytes. Other pathological conditions such as bacteria-like inclusion and intracellular bacteria were also observed in the same organs. Further investigations are needed particularly on other molluscs present at the study area. Understanding the morphology and pathology of parasites infecting mollusks are very important for management of the resources.

  18. Kinesthetic taping improves walking function in patients with stroke

    DEFF Research Database (Denmark)

    Boeskov, Birgitte; Carver, Line Tornehøj; von Essen-Leise, Anders

    2014-01-01

    BACKGROUND: Stroke is an important cause of severe disability and impaired motor function. Treatment modalities that improve motor function in patients with stroke are needed. The objective of this study was to investigate the effect of kinesthetic taping of the anterior thigh and knee on maximal...... be a valuable adjunct in physical therapy and rehabilitation of patients with stroke....

  19. Cutting red tape: national strategies for administrative simplification

    National Research Council Canada - National Science Library

    Cerri, Fabienne; Hepburn, Glen; Barazzoni, Fiorenza

    2006-01-01

    ... when the topic was new, and had a strong focus on the tools used to simplify administrative regulations. Expectations are greater today, and ad hoc simplification initiatives have in many cases been replaced by comprehensive government programmes to reduce red tape. Some instruments, such as one-stop shops, which were new then, have become widely adop...

  20. Researchers wrangle petabytes of data storage with NAS, tape

    CERN Multimedia

    Pariseau, Beth

    2007-01-01

    "Much is made in the enterprise data storage industry about the performance of disk systems over tape drives, but the managers of one data center that has eached the far limits of capacity say otherwise. Budget and performance demands forced them to build access protocols and data management tools for disk systems from scratch."

  1. Kodak phase-change media for optical tape applications

    Science.gov (United States)

    Tyan, Yuan-Sheng; Preuss, Donald R.; Olin, George R.; Vazan, Fridrich; Pan, Kee-Chuan; Raychaudhuri, Pranab. K.

    1993-01-01

    The SbInSn phase-change write-once optical medium developed by Eastman Kodak Company is particularly suitable for development into the next generation optical tape media. Its performance for optical recording has already been demonstrated in some of the highest performance optical disk systems. Some of the key performance features are presented.

  2. Standard Practice for Sampling for Particulate Contamination by Tape Lift

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2006-01-01

    1.1 This practice covers procedures for sampling surfaces to determine the presence of particulate contamination, 5 m and larger. The practice consists of the application of a pressure-sensitive tape to the surface followed by the removal of particulate contamination with the removal of the tape. The tape with the adhering particles is then mounted on counting slides. Counting and measuring of particles is done by standard techniques. 1.2 This practice describes the materials and equipment required to perform sampling of surfaces for particle counting and sizing. 1.3 The criteria for acceptance or rejection of a part for conformance to surface cleanliness level requirements shall be determined by the user and are not included in this practice. 1.4 This practice is for use on surfaces that are not damaged by the application of adhesive tape. The use of this practice on any surface of any material not previously tested or for which the susceptibility to damage is unknown is not recommended. In general, metal...

  3. Tape casting and partial melting of Bi-2212 thick films

    Energy Technology Data Exchange (ETDEWEB)

    Buhl, D.; Lang, T.; Heeb, B. [Nichtmetallische Werkstoffe, Zuerich (Switzerland)] [and others

    1994-12-31

    To produce Bi-2212 thick films with high critical current densities tape casting and partial melting is a promising fabrication method. Bi-2212 powder and organic additives were mixed into a slurry and tape casted onto glass by the doctor blade tape casting process. The films were cut from the green tape and partially molten on Ag foils during heat treatment. We obtained almost single-phase and well-textured films over the whole thickness of 20 {mu}m. The orientation of the (a,b)-plane of the grains were parallel to the substrate with a misalignment of less than 6{degrees}. At 77K/OT a critical current density of 15`000 A/cm{sup 2} was reached in films of the dimension 1cm x 2cm x 20{mu}m (1{mu}V/cm criterion, resistively measured). At 4K/OT the highest value was 350`000 A/cm{sup 2} (1nV/cm criterion, magnetically measured).

  4. Modeling and Velocity Tracking Control for Tape Drive System ...

    African Journals Online (AJOL)

    Modeling and Velocity Tracking Control for Tape Drive System. ... Journal of Applied Sciences and Environmental Management ... The result of the study revealed that 7.07, 8 and 10 of koln values met the design goal and also resulted in optimal control performance with the following characteristics 7.31%,7.71% , 9.41% ...

  5. Fabrication of laminated Bi-2212/Ag multifilamentary tape

    Science.gov (United States)

    Yuan, D.-W.; Majer, W. J.; Francavilla, T. L.

    2000-03-01

    The powder-in-tube (PIT) process has been successfully used to make long lengths of Ag-sheathed oxide superconductors. A modified PIT approach is proposed to fabricate conductors with laminated Bi-2212 configurations. Ag/Bi-2212 tapes consisting of seven laminae were produced with various thicknesses ranging from 0.38 to 0.25 mm. The use of a turkshead was found to be beneficial, yielding tapes with good dimensional integrity and consistency. Critical current density (Jc ) values greater than 105 A cm-2 (0.01 T and Bicons/Journals/Common/perp" ALT="perp" ALIGN="TOP"/> tape surface) have been attained for tapes of different thicknesses. Nonetheless, Jc was found to be related to the average thickness of individual Bi-2212 lamina. It is believed that excessive cold working accounts for the decrease in Jc with decreasing size below a threshold value. The enhancement of Jc is attributed to the high Bi-2212 grain alignment along the Ag-oxide interfaces and uniform dimensions within the laminate conductors.

  6. The Catalog: A Flexible Data Structure for Magnetic Tape.

    Science.gov (United States)

    Kay, Martin; Ziehe, Theodore

    This report outlines a generalized storage scheme for large files of highly structured data, or catalogs, and describes their realization on magnetic tape. Each datum, large or small, is assigned to one of a number of data classes of which a user may define any number. The over-all organization of a catalog is given by a map that imposes a tree…

  7. Cervical ectopic pregnancy: Mersilene tape in surgical management

    African Journals Online (AJOL)

    2 Division of Obstetrics and Gynaecology, Mediclinic Hospital, Nelspruit, Mpumalanga, South Africa. Corresponding author: A A ... case of cerv ical ectopic pregnancy that was managed using cervical cerclage with Mersilene tape as an interven tion to reduce intraoperative haemorrhage during evacuation. Case report.

  8. Numerical Modeling of Fluid Flow in the Tape Casting Process

    DEFF Research Database (Denmark)

    Jabbari, Masoud; Hattel, Jesper Henri

    2011-01-01

    The flow behavior of the fluid in the tape casting process is analyzed. A simple geometry is assumed for running the numerical calculations in ANSYS Fluent and the main parameters are expressed in non-dimensional form. The effect of different values for substrate velocity and pressure force...

  9. Oblique sputtered and evaporated magnetic thin films for tape recording

    NARCIS (Netherlands)

    Bijker, M.D.

    1998-01-01

    After having introduced some aspects of tape recording in chapter one, chapter two deals with the magnetron sputtering process itself. The kinetic energy of the electrons which are bound to the groove region by the combined action of the B and E field, was calculated. It was found that for a

  10. Critical current of high Tc superconducting Bi223/Ag tapes

    NARCIS (Netherlands)

    Huang, Y.; ten Haken, Bernard; ten Kate, Herman H.J.

    1998-01-01

    The magnetic field dependence of the critical current of various high Tc superconducting Bi2223/Ag tapes indicates that the transport current is carried through two paths: one is through weakly-linked grain boundaries (Josephson junctions); another is through well-connected grains. The critical

  11. Carbon tape microsampling for non-destructive analyses of artefacts

    Czech Academy of Sciences Publication Activity Database

    Bartůněk, V.; Varadzin, Ladislav; Zavřel, Jan

    -, - (2017) ISSN 1866-9557 R&D Projects: GA ČR(CZ) GAP405/10/2334 Institutional support: RVO:67985912 Keywords : microsampling * SEM-EDS * conducting SEM carbon tape * non-ferrous metallurgy * moulds * Early Middle Ages Subject RIV: AC - Archeology, Anthropology, Ethnology OBOR OECD: Archaeology Impact factor: 1.844, year: 2016

  12. Strategic flat rolling of Ag/BSCCO-2223 tapes

    DEFF Research Database (Denmark)

    Nielsen, Morten Storgård; Bech, Jakob Ilsted; Eriksen, Morten

    2002-01-01

    In the process of single-step flat rolling of multifilament Ag/BSCCO-2223 wire to tape previous work has shown the optimum strategy giving maximum critical current density to be it balance between the length and width strain, so they are of equal size i.e. so, that the logarithmic strain ratio, L...

  13. The Manila clam population in Arcachon Bay (SW France): Can it be kept sustainable?

    Science.gov (United States)

    Dang, Cécile; de Montaudouin, Xavier; Gam, Mériame; Paroissin, Christian; Bru, Noëlle; Caill-Milly, Nathalie

    2010-02-01

    The venerid clam Ruditapes philippinarum is the most prominent suspension-feeding bivalve inhabiting muddy intertidal seagrass beds in Arcachon Bay (SW France). It is exploited by fishermen, and Arcachon Bay ranks number one in France in terms of production and total biomass of this species. Previous studies revealed a decrease in the standing stock of R. philippinarum since 2003 and unbalanced length-frequency distributions with a lack of juveniles and of adults > 40 mm. Consequently, the population dynamics of this bivalve were studied at four intertidal sites and one oceanic site in Arcachon Bay. As clam size structure did not allow classical dynamics computations, field monitoring was coupled with field experiments (tagging-recapture) over two years. Monitoring of condition index and gonadal maturation stages highlighted a high variability in spawning number and intensity between sites. Recruitment events in the exploited area varied spatially but with uniformly low values. Von Bertalanffy Growth Function (VBGF) parameters ( K, L∞) were determined using Appeldoorn and ELEFAN methods. In the exploited sites in the inner lagoon, K was relatively high (mean = 0.72 yr - 1 ) but L∞ was low (mean = 41.1 mm) resulting in a moderate growth performance index (Φ' = 2.99). Growth parameters were not correlated with immersion time and L∞ was different between sites. Comparison of mortality coefficients ( Z) between cage experiments and field monitoring suggested that fishing accounts for 65-75% of total adult mortality. Low recruitment, a low growth rate and a normal mortality rate led to low somatic production (4.1 and 8.7 g Shell-Free Dry Weight (SFDW) m - 2 yr - 1 ) and an annual P/ B ratio from 0.44 to 0.92 yr - 1 . Under current conditions, the possibility of a sustainable population in Arcachon Bay will strongly depend on recruitment success and fishing management.

  14. Influence of the invasive Asian clam Corbicula fluminea (Bivalvia: Corbiculidae) on estuarine epibenthic assemblages

    Science.gov (United States)

    Ilarri, M. I.; Souza, A. T.; Antunes, C.; Guilhermino, L.; Sousa, R.

    2014-04-01

    One of the most widespread invasive alien species (IAS) in aquatic ecosystems is the Asian clam Corbicula fluminea. Several studies have shown that C. fluminea can cause large-scale changes in macrozoobenthic assemblages; however, very few attempted to investigate the effects of this IAS on mobile epibenthic species, such as fishes and crustaceans. In this context, the influence of C. fluminea on epibenthic species was investigated during one year by comparing the associated epibenthic fauna in three nearby sites of the Minho estuary (NW of the Iberian Peninsula), wherein the abiotic conditions are similar but the density of the Asian clam is highly different. From a total of 13 species, six were significantly influenced by C. fluminea; five responded positively, namely the brown shrimp Crangon crangon, the European eel Anguilla anguilla, the common goby Pomatoschistus microps, the brown trout Salmo trutta fario and the great pipefish Syngnathus acus, whereas the shore crab Carcinus maenas was negatively influenced. However, stomach contents analysis revealed that fish and crustacean species do not feed on C. fluminea, suggesting that this IAS is still not a large component of the diet of higher trophic levels in this estuarine ecosystem. Our results suggest that the structure provided by C. fluminea shells is likely to be one of the main factors responsible for the differences observed. C. fluminea physical structure seems to influence the epibenthic associated fauna, when found in densities higher than 1000 ind./m2, with sedentary small-bodied crustaceans and fishes being mainly attracted by the increasing in habitat complexity and consequent enhancement of heterogeneity and shelter availability.

  15. Ecotoxicological evaluation of tributyltin toxicity to the equilateral venus clam, Gomphina veneriformis (Bivalvia: Veneridae).

    Science.gov (United States)

    Park, Kiyun; Kim, Rosa; Park, Jung Jun; Shin, Hyun Chool; Lee, Jung Sick; Cho, Hyeon Seo; Lee, Yeon Gyu; Kim, Jongkyu; Kwak, Inn-Sil

    2012-03-01

    Tributyltin (TBT) is the most common pesticide in marine and freshwater environments. To evaluate the potential ecological risk posed by TBT, we measured biological responses such as growth rate, gonad index, sex ratio, the percentage of intersex gonads, filtration rate, and gill abnormalities in the equilateral venus clam (Gomphina veneriformis). Additionally, the biochemical and molecular responses were evaluated in G. veneriformis exposed to various concentrations of TBT. The growth of G. veneriformis was significantly delayed in a dose-dependent manner after exposure to all tested TBT concentrations. After TBT was administered to G. veneriformis, the gonad index decreased and the sex balance was altered. The percentage of intersex gonads also increased significantly in treated females, whereas no intersex gonads were detected in the solvent control group. Additionally, intersex gonads were detected in male G. veneriformis specimens exposed to relatively high TBT concentrations (20 μg L⁻¹). The filtration rate was also reduced in a dose-dependent manner in TBT-exposed G. veneriformis. We also noted abnormal gill morphology in TBT-exposed G. veneriformis. Furthermore, increases in antioxidant enzyme activities were observed in TBT-exposed G. veneriformis clams, regardless of dosage. Vitellogenin gene expression also increased significantly in a dose-dependent manner in G. veneriformis exposed to TBT. These results provide valuable information regarding our understanding of the toxicology of TBT in G. veneriformis. Moreover, the responses of biological and molecular factors could be utilized as information for risk assessments and marine monitoring of TBT toxicity. Crown Copyright © 2011. Published by Elsevier Ltd. All rights reserved.

  16. The Whole-Genome and Transcriptome of the Manila Clam (Ruditapes philippinarum).

    Science.gov (United States)

    Mun, Seyoung; Kim, Yun-Ji; Markkandan, Kesavan; Shin, Wonseok; Oh, Sumin; Woo, Jiyoung; Yoo, Jongsu; An, Hyesuck; Han, Kyudong

    2017-06-01

    The manila clam, Ruditapes philippinarum, is an important bivalve species in worldwide aquaculture including Korea. The aquaculture production of R. philippinarum is under threat from diverse environmental factors including viruses, microorganisms, parasites, and water conditions with subsequently declining production. In spite of its importance as a marine resource, the reference genome of R. philippinarum for comprehensive genetic studies is largely unexplored. Here, we report the de novo whole-genome and transcriptome assembly of R. philippinarum across three different tissues (foot, gill, and adductor muscle), and provide the basic data for advanced studies in selective breeding and disease control in order to obtain successful aquaculture systems. An approximately 2.56 Gb high quality whole-genome was assembled with various library construction methods. A total of 108,034 protein coding gene models were predicted and repetitive elements including simple sequence repeats and noncoding RNAs were identified to further understanding of the genetic background of R. philippinarum for genomics-assisted breeding. Comparative analysis with the bivalve marine invertebrates uncover that the gene family related to complement C1q was enriched. Furthermore, we performed transcriptome analysis with three different tissues in order to support genome annotation and then identified 41,275 transcripts which were annotated. The R. philippinarum genome resource will markedly advance a wide range of potential genetic studies, a reference genome for comparative analysis of bivalve species and unraveling mechanisms of biological processes in molluscs. We believe that the R. philippinarum genome will serve as an initial platform for breeding better-quality clams using a genomic approach. © The Author 2017. Published by Oxford University Press on behalf of the Society for Molecular Biology and Evolution.

  17. Abundance of Vibrio cholerae, V. vulnificus, and V. parahaemolyticus in oysters (Crassostrea virginica) and clams (Mercenaria mercenaria) from Long Island sound.

    Science.gov (United States)

    Jones, Jessica L; Lüdeke, Catharina H M; Bowers, John C; DeRosia-Banick, Kristin; Carey, David H; Hastback, William

    2014-12-01

    Vibriosis is a leading cause of seafood-associated morbidity and mortality in the United States. Typically associated with consumption of raw or undercooked oysters, vibriosis associated with clam consumption is increasingly being reported. However, little is known about the prevalence of Vibrio spp. in clams. The objective of this study was to compare the levels of Vibrio cholerae, Vibrio vulnificus, and Vibrio parahaemolyticus in oysters and clams harvested concurrently from Long Island Sound (LIS). Most probable number (MPN)-real-time PCR methods were used for enumeration of total V. cholerae, V. vulnificus, V. parahaemolyticus, and pathogenic (tdh(+) and/or trh(+)) V. parahaemolyticus. V. cholerae was detected in 8.8% and 3.3% of oyster (n = 68) and clam (n = 30) samples, with levels up to 1.48 and 0.48 log MPN/g in oysters and clams, respectively. V. vulnificus was detected in 97% and 90% of oyster and clam samples, with median levels of 0.97 and -0.08 log MPN/g, respectively. V. parahaemolyticus was detected in all samples, with median levels of 1.88 and 1.07 log MPN/g for oysters and clams, respectively. The differences between V. vulnificus and total and pathogenic V. parahaemolyticus levels in the two shellfish species were statistically significant (P oysters than in hard clams. Additionally, the data suggest differences in vibrio populations between shellfish harvested from different growing area waters within LIS. These results can be used to evaluate and refine illness mitigation strategies employed by risk managers and shellfish control authorities. Copyright © 2014, American Society for Microbiology. All Rights Reserved.

  18. Study on influence of irradiation vulcanization to silicon rubber autohesive tape's properties

    International Nuclear Information System (INIS)

    Chen Chun; Tang Jian; Wu Ling; Han Yingchun; Zhou Hong; Mo Yan; Fu Haijun

    2006-01-01

    After using 60 Co γ-ray to irradiate vulcanization silicon rubber autohesive tape, the effect of absorbed dose to the autohesive tape's tensile strength, elongation at break, autohesion and breakdown voltage strength and dose rate's effect to the autohesive tape's properties were studied. The results indicate that autohesive tape's tensile strength increases and the elongation at break decreases with the increasing dose. Under the dose of 25 kGy, the tape's autohesion increases with the increasing dose. When the dose is up to 25 kGy, the tape's autohesion achieves to the maximum, and then decreases with the increasing dose. Absorbed dose has no effect to the tape's breakdown voltage strength, and the dose rate has no effect to the autohesive tape's properties. (authors)

  19. Optimization of the tape placement process parameters for carbon–PPS composites

    NARCIS (Netherlands)

    Grouve, Wouter Johannes Bernardus; Warnet, Laurent; Rietman, B.; Visser, Roy; Akkerman, Remko

    2013-01-01

    The interrelation between process parameters, material properties and interlaminar bond strength is investigated for the laser assisted tape placement process. Unidirectionally carbon reinforced poly(phenylene sulfide) (PPS) tapes were welded onto carbon woven fabric reinforced PPS laminates. The

  20. Morphological and functional characterization of hemocytes from two deep-sea vesicomyid clams Phreagena okutanii and Abyssogena phaseoliformis.

    Science.gov (United States)

    Tame, Akihiro; Ozawa, Genki; Maruyama, Tadashi; Yoshida, Takao

    2018-03-01

    Deep-sea vesicomyid clams harboring intracellular symbiotic sulfur-oxidizing bacteria are often dominant in chemosynthetic animal communities. Although they are known to have erythrocytes, little is known about other hemocytes. To investigate the types and roles of various hemocytes in vesicomyid clams, we performed morphological, histochemical and functional characterization of the hemocytes in two species, Phreagena okutanii, collected from 873 to 978 m depth, and Abyssogena phaseoliformis, from 5199 to 5355 m. Both were found to have three types of hemocytes: erythrocytes (ERCs), eosinophilic granulocytes (EGs), and basophilic granulocytes (BGs). The ERCs contain hemoglobin in the cytoplasm, with basophilic vacuoles containing acid polysaccharide, neutral lipids, and peroxidase. The EGs were found to contain acid polysaccharides and eosinophilic granules containing lysosomal enzymes, acid and alkaline phosphatases, chloroacetate esterase, and peroxidase. Although BGs had some basophilic granules with alkaline phosphatase, they lacked acid phosphatase and acid polysaccharides. The EGs and BGs were shown to have phagocytic ability, while the ERCs exhibited no phagocytosis. The EGs showed higher phagocytic activity as well as a higher phagosome-lysosome fusion rate than BGs. The hemocytes of the two vesicomyid species differed in the intracellular structures. In A. phaseoliformis, ERCs additionally contained neutral polysaccharides in vacuoles and had vesicles with acinus-like acidic mucus in the cytoplasm, neither of which were observed in P. okutanii. The eosinophilic granules in the EGs had heteromorphically-elongated shapes containing homogeneously electron-dense material in P. okutanii, but were more spherical and composed of fibrous structures in A. phaseoliformis. The difference in hemocytes between the two clams seems to be reflective of phylogenetically differentiated lineages adapting to differing conditions in their respective deep-sea environments

  1. Temporary ectropion therapy by adhesive taping: a case study

    Directory of Open Access Journals (Sweden)

    Habermann Anke

    2008-07-01

    Full Text Available Abstract Introduction Various surgical procedures are available to correct paralytic ectropion, which are applied in irreversible facial paresis. Problems occur when facial paresis has an unclear prognosis, since surgery of the lower eyelid is usually irreversible. We propose a simple method to correct temporary ectropion in facial palsy by applying an adhesive strip. Patients and methods Ten patients with peripheral facial paresis and paralytic ectropion were treated with an adhesive strip to correct paralytic ectropion. We used "Steri-Strips" (45 × 6.0 mm, which were taped on the carefully cleaned skin of the lower eyelid and of the adjacent zygomatic region until the prognosis of the paresis was clarified. In addition to the examiner's evaluation of the lower lacrimal point in the lacrimal lake, subjective improvement of the symptoms was assessed using a visual analogue scale (VAS, 1–10. Results 9 patients reported a clear improvement of the symptoms after adhesive taping. There was a clear regression of tearing (VAS (median = 8; 1 = no improvement, 10 = very good improvement, the cosmetic impairment of the adhesive tape was low (VAS (median = 2.5; 1 = no impairment, 10 = severe impairment and most of the patients found the use of the adhesive strip helpful. There was slight reddening of the skin in one case and well tolerated by the facial skin in the other cases. Conclusion The cause and location of facial nerve damage are decisive for the type of surgical therapy. In potentially reversible facial paresis, procedures should be used that are easily performed and above all reversible without complications. Until a reliable prognosis of the paresis can be made, adhesive taping is suited for the temporary treatment of paralytic ectropion. Adhesive taping is simple and can be performed by the patient.

  2. Ultrasound assessment of tension-free vaginal tape (TVT).

    Science.gov (United States)

    Flock, F; Kohorst, F; Kreienberg, R; Reich, A

    2011-01-01

    To date, no standardization for the visualization of tension-free vaginal tape (TVT) has been established in clinical practice. The aim of this prospective observational study was to evaluate the shape and position of the tape using ultrasound and to compare this data with clinical postoperative results. In a three-year period, 296 patients with clinically and urodynamically proven stress urinary incontinence (SUI) were treated with TVT and received follow-up in our department. An additional 12 patients, who were initially treated in other hospitals and had postoperative problems, were included in this study. Depending on the outcome after 3 months, the patients were divided into groups with and without specific disorders. The TVT was evaluated by introital ultrasound. The position of the tape was established by its location in relation to the urethral length and the distance to the hypoechoic center of the urethra (HCU). A suitable TVT position was determined in patients without any postoperative disorders. The mean value for the TVT position at rest in relation to the urethral length was 61 %. The distance to the HCU was 4.6 ± 1.5 mm. In patients with persistent SUI, the tape was more often located under the inner (3 % vs. 0 %) or outer quarter (29 % vs. 13 %, p = 0.004). In patients with residual volume, the distance to the urethra was significantly lower (2.7 vs. 4.6, p TVT may be regularly investigated using ultrasound. In combination with the clinical outcome, it represents an important method of evaluating the tape and assists in the planning of a future therapeutic course of action in cases of postoperative problems. © Georg Thieme Verlag KG Stuttgart · New York.

  3. Bioavailability of polycyclic aromatic hydrocarbons (PAHs) to short-neck clam (Paphia undulata) from sediment matrices in mudflat ecosystem of the west coast of Peninsular Malaysia.

    Science.gov (United States)

    Keshavarzifard, Mehrzad; Zakaria, Mohamad Pauzi; Hwai, Tan Shau

    2017-06-01

    The bioaccumulation and bioavailability of polycyclic aromatic hydrocarbons (PAHs) were characterized in sediment and Paphia undulata (short-neck clam) from six mudflat areas in the west coasts of Peninsular Malaysia. The concentrations of total PAHs varied from 357.1 to 6257.1 and 179.9 ± 7.6 to 1657.5 ± 53.9 ng g -1 dry weight in sediment and short-neck clam samples, respectively. PAHs can be classified as moderate to very high level of pollution in sediments and moderate to high level of pollution in short-neck clams. The diagnostic ratios of individual PAHs and principal component analysis indicate both petrogenic and pyrogenic sources with significant dominance of pyrogenic source. The first PAHs biota-sediment accumulation factors and relative biota-sediment accumulation factors data for short-neck clam were obtained in this study, indicating a preferential accumulation of lower molecular weight PAHs. Evaluation of PAH levels in sediments and short-neck clams indicates that short-neck clam could be introduced as a good biomonitor in mudflats. The results also demonstrated that under environmental conditions, the sedimentary load of hydrocarbons appears to be one of the factors controlling their bioavailability to biota.

  4. Distribution of 137Cs activities in clams, Tivela mactroidea collected along the northern coast of Venezuela and the island of Margarita

    International Nuclear Information System (INIS)

    LaBrecque, J.J.; Alfonso, J.A.; Cordoves, P.R.

    2007-01-01

    Clam meats were obtained directly from the fishermen on the beaches in front of where the clams were collected at eight sites; seven along the northern coast of Venezuela and one on the northern coast of the island of Margarita (Venezuela). Marine sediments were also collected in the same corresponding areas as the clams. 137 Cs was determined both in clam meats and the marine sediments by high resolution gamma-ray spectrometry employing a hyperpure germanium detector. About 5 kg portions of clam meats were washed and dried in the laboratory, before 500 cm 3 volumes were transferred and weighed in the measuring containers. Similarly, 500 cm 3 volumes of marine sediments that were dried and ground to pass a 85 μm sieve were transferred to the measuring containers. The samples were counted for 150,000 seconds of real time. The 137 Cs activity of the clam meats ranged from -1 (our detection limit) to 0.36 Bq x kg -1 (dried weigh). These values are all within the range of values considered for environmental fallout from the nuclear weapons tests. Finally, all the values for the corresponding marine sediments were below our detection limit of 0.1 Bq x kg -1 of 137 Cs (dried weigh). (author)

  5. Wave actions and topography determine the small-scale spatial distribution of newly settled Asari clams Ruditapes philippinarum on a tidal flat

    Science.gov (United States)

    Nambu, Ryogen; Saito, Hajime; Tanaka, Yoshio; Higano, Junya; Kuwahara, Hisami

    2012-03-01

    There are many studies on spatial distributions of Asari clam Ruditapes philippinarum adults on tidal flats but few have dealt with spatial distributions of newly settled Asari clam (physical/topographical conditions on tidal flats. We examined small-scale spatial distributions of newly settled individuals on the Matsunase tidal flat, central Japan, during the low spring tides on two days 29th-30th June 2007, together with the shear stress from waves and currents on the flat. The characteristics of spatial distribution of newly settled Asari clam markedly varied depending on both of hydrodynamic and topographical conditions on the tidal flat. Using generalized linear models (GLMs), factors responsible for affecting newly settled Asari clam density and its spatial distribution were distinguished between sampling days, with "crest" sites always having a negative influence each on the density and the distribution on both sampling days. The continuously recorded data for the wave-current flows at the "crest" site on the tidal flat showed that newly settled Asari clam, as well as bottom sediment particles, at the "crest" site to be easily displaced. Small-scale spatial distributions of newly settled Asari clam changed with more advanced benthic stages in relation to the wave shear stress.

  6. Properties of PTFE tape as a semipermeable membrane in fluorous reactions

    OpenAIRE

    Brendon A. Parsons; Olivia Lin Smith; Myeong Chae; Veljko Dragojlovic

    2015-01-01

    Summary In a PTFE tape phase-vanishing reaction (PV-PTFE), a delivery tube sealed with PTFE tape is inserted into a vessel which contains the substrate. The reagent diffuses across the PTFE tape barrier into the reaction vessel. PTFE co-polymer films have been found to exhibit selective permeability towards organic compounds, which was affected by the presence of solvents. In this study, we attempted to establish general trends of permeability of PTFE tape to different compounds and to better...

  7. Enhancement of turbulent flow heat transfer in a tube with modified twisted tapes

    Energy Technology Data Exchange (ETDEWEB)

    Lei, Y.G.; Zhao, C.H.; Song, C.F. [College of Environmental Science and Engineering, Taiyuan University of Technology, Taiyuan (China)

    2012-12-15

    Numerical simulations were performed to study the fluid flow and heat transfer in a tube with staggered twisted tapes with central holes. In the range of Reynolds numbers between 6000 and 28 000, the modified twisted tapes increased the Nusselt number by 76.2 {proportional_to} 149.7 % and the friction factor by 380.2 {proportional_to} 443.8 % compared to the smooth tube. Compared to the typical twisted tapes, the modified twisted tapes produced an acceleration flow through the triangle regions leading to the enhancement of heat transfer, and the holes in the modified tapes reduced the severe pressure loss. It was found that the modified twisted tapes decreased the friction factor by 8.0 {proportional_to} 16.1 % and enhanced the heat transfer by 34.1 {proportional_to} 46.8 % in comparison with the typical tapes. These results indicated that the performance ratio values of the tube with modified twisted tapes were higher than 1.0 in the range of Reynolds numbers studied. The computed performance ratios of the tube with modified twisted tapes were much higher than those of the tube with typical twisted tapes. This means that the integrated performance of the tube with staggered twisted tapes with central holes is superior to that of the tube with typical twisted tapes. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  8. 21 CFR 878.4730 - Surgical skin degreaser or adhesive tape solvent.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Surgical skin degreaser or adhesive tape solvent... Surgical skin degreaser or adhesive tape solvent. (a) Identification. A surgical skin degreaser or an adhesive tape solvent is a device that consists of a liquid such as 1,1,2-trichloro-1,2,2-trifluoroethane...

  9. Systems-level modeling the effects of arsenic exposure with sequential pulsed and fluctuating patterns for tilapia and freshwater clam

    International Nuclear Information System (INIS)

    Chen, W.-Y.; Tsai, J.-W.; Ju, Y.-R.; Liao, C.-M.

    2010-01-01

    The purpose of this paper was to use quantitative systems-level approach employing biotic ligand model based threshold damage model to examine physiological responses of tilapia and freshwater clam to sequential pulsed and fluctuating arsenic concentrations. We tested present model and triggering mechanisms by carrying out a series of modeling experiments where we used periodic pulses and sine-wave as featured exposures. Our results indicate that changes in the dominant frequencies and pulse timing can shift the safe rate distributions for tilapia, but not for that of freshwater clam. We found that tilapia increase bioenergetic costs to maintain the acclimation during pulsed and sine-wave exposures. Our ability to predict the consequences of physiological variation under time-varying exposure patterns has also implications for optimizing species growing, cultivation strategies, and risk assessment in realistic situations. - Systems-level modeling the pulsed and fluctuating arsenic exposures.

  10. Systems-level modeling the effects of arsenic exposure with sequential pulsed and fluctuating patterns for tilapia and freshwater clam

    Energy Technology Data Exchange (ETDEWEB)

    Chen, W.-Y. [Department of Bioenvironmental Systems Engineering, National Taiwan University, Taipei 10617, Taiwan (China); Tsai, J.-W. [Institute of Ecology and Evolutionary Ecology, China Medical University, Taichung 40402, Taiwan (China); Ju, Y.-R. [Department of Bioenvironmental Systems Engineering, National Taiwan University, Taipei 10617, Taiwan (China); Liao, C.-M., E-mail: cmliao@ntu.edu.t [Department of Bioenvironmental Systems Engineering, National Taiwan University, Taipei 10617, Taiwan (China)

    2010-05-15

    The purpose of this paper was to use quantitative systems-level approach employing biotic ligand model based threshold damage model to examine physiological responses of tilapia and freshwater clam to sequential pulsed and fluctuating arsenic concentrations. We tested present model and triggering mechanisms by carrying out a series of modeling experiments where we used periodic pulses and sine-wave as featured exposures. Our results indicate that changes in the dominant frequencies and pulse timing can shift the safe rate distributions for tilapia, but not for that of freshwater clam. We found that tilapia increase bioenergetic costs to maintain the acclimation during pulsed and sine-wave exposures. Our ability to predict the consequences of physiological variation under time-varying exposure patterns has also implications for optimizing species growing, cultivation strategies, and risk assessment in realistic situations. - Systems-level modeling the pulsed and fluctuating arsenic exposures.

  11. Developmental Transcriptome Analysis and Identification of Genes Involved in Larval Metamorphosis of the Razor Clam, Sinonovacula constricta.

    Science.gov (United States)

    Niu, Donghong; Wang, Fei; Xie, Shumei; Sun, Fanyue; Wang, Ze; Peng, Maoxiao; Li, Jiale

    2016-04-01

    The razor clam Sinonovacula constricta is an important commercial species. The deficiency of developmental transcriptomic data is becoming the bottleneck of further researches on the mechanisms underlying settlement and metamorphosis in early development. In this study, de novo transcriptome sequencing was performed for S. constricta at different early developmental stages by using Illumina HiSeq 2000 paired-end (PE) sequencing technology. A total of 112,209,077 PE clean reads were generated. De novo assembly generated 249,795 contigs with an average length of 585 bp. Gene annotation resulted in the identification of 22,870 unigene hits against the NCBI database. Eight unique sequences related to metamorphosis were identified and analyzed using real-time PCR. The razor clam reference transcriptome would provide useful information on early developmental and metamorphosis mechanisms and could be used in the genetic breeding of shellfish.

  12. Structural properties of superconducting Bi-2223/Ag tapes

    Energy Technology Data Exchange (ETDEWEB)

    Gottschalck Andersen, L.

    2001-05-01

    The structural properties of silver clad high-T{sub c} superconducting ceramic tapes of (Bi,Pb){sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub x} (Bi-2223) have been investigated by means of synchrotron X-ray diffraction (including the 3DXRD microscope setup), transmission electron microscopy (TEM) and scanning electron microscopy (SEM) with energy dispersive X-ray analysis (EDS). By synchrotron X-ray diffraction in situ studies of the phase development during the transformation of (Bi,Pb){sub 2}Sr{sub 2}Ca{sub 1}Cu{sub 2}O{sub x} (Bi-2212) into Bi-2223, the stoichiometry changes and the texture have been performed during annealing in 8% O{sub 2} and in air. Furthermore, an annealing with two high temperature cycles has been performed to study the equilibrium phenomena. During heating (Ca,Sr){sub 2}PbO{sub 4} decomposes at temperatures between 700 deg. C and 840 deg.C. Simultaneously, the Bi-2212 lattice contracts, indicating an incorporation of Pb. Moreover, the grain mis-alignment decreases significantly. In air we have observed that Bi-2212 partly dissociates into (Ca,Sr){sub 2}CuO{sub 3} and a liquid at temperatures above 812 deg. C. At the annealing temperature Bi-2212 and (Ca,Sr){sub 2}CuO{sub 3} react with the liquid to form Bi-2223. The transformation mechanism is discussed. During cooling below {approx}750 deg.C (Ca,Sr){sub 2}CuO{sub 3} and the liquid mainly transform into Bi-2201. Below {approx}780 deg. C Bi-2223 decomposes to 3221. In addition, a two-step cooling experiment and a decomposition study have been performed in 8% O{sub 2}. By TEM the grain and colony size in the c-axis direction, the angles of c-axis tilt grain boundaries and the intergrowth content are investigated. A fully processed tape has on average 50% thicker grains than a tape after the 1st annealing. The angles of c-axis tilt grain boundaries are on average 14 deg. and 26 deg. for the fully processed tape and the tape after the 1st annealing, respectively. The intergrowth content (15%) and

  13. Effect of the Kinesio tape to muscle activity and vertical jump performance in healthy inactive people

    Directory of Open Access Journals (Sweden)

    Lu Szu-Ching

    2011-08-01

    Full Text Available Abstract Background Elastic taping applied on the triceps surae has been commonly used to improve the performance of lower extremities. However, little objective evidence has been documented. The purpose of this study was to investigate the effect of elastic taping on the triceps surae during a maximal vertical jump. It was hypothesized that elastic taping to the triceps surae would increase muscle activity and cause positive effect to jump height. Methods Thirty-one healthy adults (19 males and 12 females with mean age, body weight and height for 25.3 ± 3.8 years old, 64.1 ± 6.2 kg, and 169.4 ± 7.3 cm, respectively were recruited. All participants performed vertical jump tests prior to (without taping and during elastic taping. Two elastic tapes, Kinesio tape and Mplacebo tape from two different manufacturers, were applied to the participants, respectively. Results The results showed that the vertical ground reaction force increased when Kinesio tape was applied even when the height of jump remained about constant. However, the height of the jump decreased, and there was no difference on the vertical ground reaction force in Mplacebo taping group. Although the EMG activity of medial gastrocnemius tended to increase in Kinesio taping group, we did not see differences in EMG activity for the medial gastrocnemius, tibialis anterior and soleus muscles in either group. Conclusions Based on the varied effects of Kinesio tape and Mplacebo tape, different intervention technique was suggested for specific purpose during vertical jump movement. Mplacebo tape was demanded for the benefits of stabilization, protection, and the restriction of motion at the ankle joint. On the other hand, the findings may implicate benefits for medial gastrocnemius muscle strength and push-off force when using Kinesio tape.

  14. Combined Effects of Temperature and Seston Concentration on the Physiological Energetics of the Manila Clam Ruditapes philippinarum.

    Directory of Open Access Journals (Sweden)

    Hee Yoon Kang

    Full Text Available The suspension-feeding Manila clam Ruditapes philippinarum is a native species of the western Pacific that is now widely distributed around the globe because of its commercial importance. To determine the adaptive physiological responses to changing thermal and nutritional conditions, clearance, filtration, feces production, ammonium excretion, respiration rates, and scope for growth (SFG were measured in adult clams. The clams were exposed to 24 treatments involving the combination of four water temperatures (8, 13, 18, and 23°C and six concentrations of suspended particulate matter (SPM: 9.5 to 350.5 mg L(-1. Physiological rates were standardized by using the mean (480 mg of tissue dry weights of experimental clams using allometric equations between physiological variables and tissue dry weight. Higher clearance rates were recorded at higher temperatures and lower SPM concentrations, and these rates decreased with increasing SPM concentration at individual temperatures. Consumed energy increased with increasing temperature and SPM concentration, peaking at around 100-200 mg L(-1 at 18-23°C. Whereas fecal energy was largely determined by SPM concentration, ammonia excretion was mainly governed by temperature. Respiration rate studies revealed a predominant quadratic effect of temperature on the metabolism, indicating a lack of acclimatory adjustment of metabolic rate to rising temperature. SFG values were positive under almost all the treatment conditions and were much higher at higher SPM concentrations (> 45 mg L(-1, with the highest level being recorded at 18°C and 100-200 mg L(-1 SPM. Increased filtration rate offset the increased metabolic cost at warm temperatures. Our holistic findings suggest that a high degree of physiological plasticity allows R. philippinarum to tolerate the wide range of temperatures and SPM concentrations that are found in tidal flats, accounting in part for the successful distribution of this species over a

  15. Shell shape analysis and spatial allometry patterns of Manila Clam (Ruditapes philippinarium) in a mesotidal coastal lagoon

    OpenAIRE

    Caill-Milly, Nathalie; Bru, Noëlle; Mahé, Kélig; D'Amico, Franck

    2012-01-01

    While gradual allometric changes of shells are intrinsically driven by genotype, morphometrical shifts can also be modulated by local environmental conditions. Consequently the common use of a unique dimension (usually length) to assess bivalves’ growth may mask phenotypic differences in valve shape among populations. A morphometric exhaustive study was conducted on Manila clam, Ruditapes philippinarum, by acquiring data in the French Arcachon Bay (intrasite phenotypic variability) and by com...

  16. Identification of larvae: The zebra mussel (Dreissena polymorpha), quagga mussel (Dreissena rosteriformis bugensis), and Asian clam (Corbicula fluminea)

    Science.gov (United States)

    Nichols, S. Jerrine; Black, M.G.

    1994-01-01

    There are presently four freshwater bivalves in the United States that produce larvae or veligers commonly found in the water column: two forms of Asian clams and two species of dreissenids. Portions of the geographic range of three of these bivalves, one species of Asian clam (Corbicula fluminea), zebra mussels (Dreissena polymorpha), and quagga mussels (Dreissena rosteriformis bugensis), overlap, causing problems with larval identification. To determine which characteristics can be used to separate larval forms, adult Asian clams, quaggas, and zebra mussels were brought into the laboratory and induced to spawn, and the resulting larvae were reared. Hybrids between quaggas and zebra mussels were also produced, but not reared to maturity. Characteristics allowing for the most rapid and accurate separation of larvae were hinge length, shell length/height, shell shape, shell size, and the presence or absence of a foot and velum. These characteristics were observed in laboratory-reared larvae of known parentage and field-caught larvae of unknown parentage. In most cases, larvae of the Asian clam can be readily separated from those produced by either type of dreissenid on the basis of shell size and presence of a foot. Separating the gametes and embryos of the two types of dreissenids is not possible, but after shell formation, most of the larval stages can be distinguished. Hinge length, shell length/height, and the similarity in size of the shell valves can be used to separate straight-hinged, umbonal, pediveliger, and plantigrade larvae. Quagga × zebra mussel hybrids show characteristics of both parents and are difficult to identify.

  17. Survival and growth of the giant clam larvae utilizing zooxanthellae from Acropora valenciennesi, Tridacna crocea and Sarcophyton trocheliophorum

    OpenAIRE

    A. Niartiningsih; Magdalena Litaay; Niradhyna W. M

    2015-01-01

    The aim of this study was to know the survival and growth of the giant clam larvae given zooxanthellae from different host. The field experiment was conducted from September ???November 2006 at hatchery of Marine Field Station Barrang Lompo Island, Makassar. Zooxanthellae hosts used were: (A) Table coral (Acropora valenciennesi); (B) Tridacna crocea, (C) soft coral (Sarcophyton trocheliophorum) and (D) control (no additional zooxanthellae). The Complete Randomized Design with four treatments ...

  18. Physiological responses to copper in giant clams: a comparison of two methods in revealing effects on photosynthesis in zooxanthellae.

    Science.gov (United States)

    Elfwing, Tina; Blidberg, Eva; Tedengren, Michael

    2002-08-01

    In the present work physiological responses to a short term, sub-lethal exposure to copper (5 microg Cu2 l(-1) were studied on two species of giant clams, Tridacna gigas and Hippopus hippopus. All giant clams (fam. Tridacnidae) maintain a symbiotic relationship with photo-synthesising microalgae (zooxanthellae) and the phytotoxic effects of this copper concentration were approached with two different end points: changes in oxygen production and maximal quantum yield (Fv/Fm). Additionally we measured respiration, whereby Pg:R ratios could be calculated for the system (algae and clam) and used as an indicator of stress. Cu accumulation was only determined for T. gigas and showed significantly higher tissue concentrations in exposed specimens (11.3 microg Cu g(-1) dry wt) compared to the controls (4.2 microg Cu g(-1)). Both species displayed significantly reduced Pg:R ratios due to exposure, mainly explained by lowered gross production. No indication of stress was shown in the fluorescence measurements and possible explanations are discussed in the paper. We propose that inhibitions in the slow kinetics of photosynthesis were not captured by this fluorescence parameter. Accordingly we suggest that measurements of maximum fluorescence yield should be accompanied by complementary parameters when studying pollutants with unclear phytotoxic mechanisms.

  19. Risk-based approach to appraise valve closure in the clam Corbicula fluminea in response to waterborne metals

    International Nuclear Information System (INIS)

    Liao, C.-M.; Jou, L.-J.; Chen, B.-C.

    2005-01-01

    We developed a risk-based approach to assess how the valve closure behavior of Asiatic clam Corbicula fluminea responds to waterborne copper (Cu) and cadmium (Cd). We reanalyzed the valve closure response data from published literature to reconstruct the response time-dependent dose-response profiles based on an empirical three-parameter Hill equation model. We integrated probabilistic exposure profiles of measured environmental Cu and Cd concentrations in the western coastal areas of Taiwan with the reconstructed dose-response relationships at different integration times of response to quantitatively estimate the valve response risk. The risk assessment results implicate exposure to waterborne Cu and Cd may pose no significant risk to clam valve activity in the short-time response periods (e.g., <30 min), yet a relative high risk for valve closure response to waterborne Cu at response times greater than 120 min is alarming. We successfully linked reconstructed dose-response profiles and EC50-time relationships associated with the fitted daily valve opening/closing rhythm characterized by a three-parameter lognormal function to predict the time-varying bivalve closure rhythm response to waterborne metals. We parameterized the proposed predictive model that should encourage a risk-management framework for discussion of future design of biological monitoring systems. - A model was developed to link valve closure in clams to concentrations of metals in water

  20. Shell Shape Analysis and Spatial Allometry Patterns of Manila Clam (Ruditapes philippinarum in a Mesotidal Coastal Lagoon

    Directory of Open Access Journals (Sweden)

    Nathalie Caill-Milly

    2012-01-01

    Full Text Available While gradual allometric changes of shells are intrinsically driven by genotype, morphometrical shifts can also be modulated by local environmental conditions. Consequently the common use of a unique dimension (usually length to assess bivalves’ growth may mask phenotypic differences in valve shape among populations. A morphometric exhaustive study was conducted on Manila clam, Ruditapes philippinarum, by acquiring data in the French Arcachon Bay (intrasite phenotypic variability and by comparing with other sites in the literature (intersite phenotypic variability. 2070 shells were subsampled, weighted, and automatically measured using TNPC software. Some ratios’ values indicate a relatively round and globular shape shell in comparison with other sites confirming poor conditions for some individuals. Among adult clams, three main morphological groups were identified and discussed according to spatial considerations. Allometric relations for pairs of shell descriptors were determined by testing classical linear and piecewise regression models on log-transformed relation of Huxley. A significant shape change correlated to size was observed; it corresponds to the second year of life of the clam. Relationships between density, disease, and shell shape are demonstrated and discussed related to other potential factors affecting shell shape. Finally, consequences on population regulation are addressed.

  1. Study of the toxic effects of flame retardant PBDE-47 on the clam Chamelea gallina (Linnaeus, 1758

    Directory of Open Access Journals (Sweden)

    Salvatora Angela Angioni

    2013-03-01

    Full Text Available The purpose of the study is to evaluate the effects of 2,2',4,4'-tetrabromodiphenylether (PBDE-47 on the Chamelea gallina clam (according to current commercial regulations: Venus gallina. PBDEs, which are used as flame retardants in various industrial products, are classed as hazardous substances by Directive 2011/65/EU. They are bioaccumulative compounds, considered to be endocrine disruptors, genotoxic, neurotoxic and practically ubiquitous, and their concentration in the environment has considerably increased in recent years. The aim of this study is to establish the effects of PBDE-47 on Chamelea gallina: toxic power and any harmful effects on the gonads, bioaccumulation capacity in the tissues, and possible entry into the food chain. The research used 96-hour and 21-day experimental tests on clams housed in filtered seawater. The tests were preceded by a period of acclimatisation of the molluscs lasting five to seven days. The clams were fed on seaweed (Dunaliella tertiolecta. The choice of the toxic compound PBDE-47 was based on the high concentration, among the congeners of PBDE, found in some aquatic species. The study demonstrated that the concentration of the contaminant used did not alter the vital functions, cause significant levels of mortality or lead to evident alteration in the gonads of Chamelea gallina. However, the research demonstrated the bioaccumulation capacity of the bivalve mollusc, allowing PBDE-47 to enter the food chain.

  2. Toxicological effects induced by cadmium in gills of Manila clam ruditapes philippinarum using NMR-based metabolomics

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Linbao; Liu, Xiaoli; You, Liping; Zhou, Di [Key Laboratory of Coastal Zone Environment Processes, CAS, Shandong Provincial Key Laboratory of Coastal Zone Environment Processes, Yantai Institute of Coastal Zone Research, Chinese Academy of Sciences, Yantai (China); The Graduate School of Chinese Academy of Sciences, Beijing (China); Yu, Junbao; Zhao, Jianmin; Wu, Huifeng [Key Laboratory of Coastal Zone Environment Processes, CAS, Shandong Provincial Key Laboratory of Coastal Zone Environment Processes, Yantai Institute of Coastal Zone Research, Chinese Academy of Sciences, Yantai (China); Feng, Jianghua [Department of Electronic Science, Fujian Key Laboratory of Plasma and Magnetic Resonance, State Key Laboratory of Physical Chemistry of Solid Surfaces, Xiamen University, Xiamen (China)

    2011-11-15

    Cadmium (Cd) has become an important heavy metal contaminant in the sediment and seawater along the Bohai Sea and been of great ecological risk due to its toxic effects to marine organisms. In this work, the toxicological effects caused by environmentally relevant concentrations (10 and 40 {mu}g L{sup -1}) of Cd were studied in the gill tissues of Manila clam Ruditapes philippinarum after exposure for 24, 48, and 96 h. Both low (10 {mu}g L{sup -1}) and high (40 {mu}g L{sup -1}) doses of Cd caused the disturbances in energy metabolism and osmotic regulation and neurotoxicity based on the metabolic biomarkers such as succinate, alanine, branched chain amino acids, betaine, hypotaurine, and glutamate in clam gills after 24 h of exposure. However, the recovery of toxicological effects of Cd after exposure for 96 h was obviously observed in clam to Cd exposures. Overall, these results indicated that NMR-based metabolomics was applicable to elucidate the toxicological effects of heavy metal contaminants in the marine bioindicator. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  3. Atypical feeding behavior of Long-tailed Ducks in the wake of a commercial fishing boat while clamming

    Science.gov (United States)

    Perry, Matthew; Osenton, Peter C.; White, Timothy P.

    2017-01-01

    A foraging group of Clangula hyemalis (Long-tailed Duck) was observed on 10 February 2010 diving behind a commercial boat that was clamming near Monomoy Island, Nantucket Sound, MA. We used a shotgun to collect 9 of the ducks, and our analyses of gizzard and gullet (esophagus and proventriculus) revealed 37 food items in the gizzard and 16 in the gullet. Mollusca were the dominant food in the gizzard (49%), whereas Crustacea were dominant in the gullet (57%). Crustacea were the second most important food in the gizzard (38%), whereas Mollusca were the second most important food in the gullet (31%). Relatively high volumes of the Amphipoda Caprella sp. (skeleton shrimp) and the Decopoda Crangon septemspinosa (Sand Shrimp) were recorded in the gullet and gizzard. Ensis directus (Atlantic Jackknife Clam) formed the greatest volume of Mollusca in the gizzard (15%) and in the gullet (15%). Long-tailed Ducks had fed on this Bivalvia and several other species of Mollusca that had no shell or broken shell when consumed. Many of the food organisms were apparently dislodged and some damaged by the clamming operation creating an opportunistic feeding strategy for the Long-tailed Ducks.

  4. Metabolic physiology of the invasive clam, Potamocorbula amurensis: the interactive role of temperature, salinity, and food availability.

    Science.gov (United States)

    Miller, Nathan A; Chen, Xi; Stillman, Jonathon H

    2014-01-01

    In biological systems energy serves as the ultimate commodity, often determining species distributions, abundances, and interactions including the potential impact of invasive species on native communities. The Asian clam Potamocorbula amurensis invaded the San Francisco Estuary (SFE) in 1986 and is implicated in the decline of native fish species through resource competition. Using a combined laboratory/field study we examined how energy expenditure in this clam is influenced by salinity, temperature and food availability. Measures of metabolism were made at whole organism (metabolic rate) and biochemical (pyruvate kinase (PK) and citrate synthase (CS) enzyme activities) levels. We found in the field, over the course of a year, the ratio of PK to CS was typically 1.0 suggesting that aerobic and fermentative metabolism were roughly equivalent, except for particular periods characterized by low salinity, higher temperatures, and intermediate food availabilities. In a 30-day laboratory acclimation experiment, however, neither metabolic rate nor PK:CS ratio was consistently influenced by the same variables, though the potential for fermentative pathways did predominate. We conclude that in field collected animals, the addition of biochemical measures of energetic state provide little additional information to the previously measured whole organism metabolic rate. In addition, much of the variation in the laboratory remained unexplained and additional variables, including reproductive stage or body condition may influence laboratory-based results. Further study of adult clams must consider the role of organismal condition, especially reproductive state, in comparisons of laboratory experiments and field observations.

  5. Establishing the norm of Cognitive Adaptive Test/Clinical Linguistic and Auditory Milestone Scale (CAT/CLAMS) in Chinese infants.

    Science.gov (United States)

    Chang, Y C; Huang, C C; Hu, S C

    1998-01-01

    The Cognitive Adaptive Test/Clinical Linguistic and Auditory Milestone Scale (CAT/CLAMS) has been recommended as a useful diagnostic tool for cognitive delay. To provide wider application of this instrument as a general screening tool for pediatricians, a normative percentile graph from a large convenience sample of Chinese infants has been established. The effects of environmental factors on early language and adaptive development were also analyzed. A total of 402 normal infants aged 4 to 36 months attending well-child clinics were recruited. These infants were from all socioeconomic strata, and half were bilingual with Mandarin and Taiwanese. Grandmothers were the chief caretakers or co-caretakers in 28% of this population. The milestones were attained in a sequential and orderly fashion. In contrast to the adaptive ability, there was a wide variation in language acquisition between age 12 and 24 months. Multiple stepwise regression of demographic and environmental factors revealed that age was the main variance in CAT score (P = 0.0001). In CLAMS score, however, age and caretakers were the significant predictors (P = 0.0001). Infants cared for by both mothers and grandmothers had higher CLAMS score by two months over those cared by mothers only (P = 0.001). Those cared for by grandmothers only had lower language score than those by mothers only, though without statistical significance (P = 0.05). Bilingualism, birth order, numbers of siblings, familial structures, and parental socioeconomic status had no effect on early development.

  6. A software package to process an INIS magnetic tape on the VAX computer

    International Nuclear Information System (INIS)

    Omar, A.A.; Mohamed, F.A.

    1991-01-01

    This paper presents a software package whose function is to process the magnetic tapes distributed by the Atomic Energy Agency, on the VAX computers. These tapes contain abstracts of papers in the different branches of nuclear field and is supplied from the international Nuclear Information system (INIS). Two goals are aimed from this paper. First it gives a procedure to process any foreign magnetic tape on the VAX computers. Second, it solves the problem of reading the INIS tapes on a non IBM computer and thus allowing the specialists to gain from the large amount of information contained in these tapes. 11 fig

  7. Kinesiology taping as an adjunct for pain management in cancer?

    Science.gov (United States)

    Banerjee, Gourav; Rebanks, Jonathan; Briggs, Michelle; Johnson, Mark I

    2016-07-14

    We present the case of a 46-year-old woman who developed severe pain described as 'tearing' and 'searing' in the left side of the mid-trapezius region near the thoracic 8 vertebra (T8). The patient had undergone surgery for T8 fracture which had resulted from metastasis (secondary breast cancer). A community nurse referred the patient for physiotherapy assessment and treatment for her musculoskeletal pain and related symptoms that had affected her mobility and functional activities. The patient was treated with soft tissue therapy with the addition of kinesiology taping on follow-up visits. Kinesiology tape was applied over her left side trapezius region and left shoulder. The patient reported significant reductions in pain severity and felt greater control and stability over her left shoulder region, which resulted in better function and overall quality of life measures. She did not report any adverse effects. 2016 BMJ Publishing Group Ltd.

  8. An Improvement in Thermal Modelling of Automated Tape Placement Process

    International Nuclear Information System (INIS)

    Barasinski, Anaies; Leygue, Adrien; Poitou, Arnaud; Soccard, Eric

    2011-01-01

    The thermoplastic tape placement process offers the possibility of manufacturing large laminated composite parts with all kinds of geometries (double curved i.e.). This process is based on the fusion bonding of a thermoplastic tape on a substrate. It has received a growing interest during last years because of its non autoclave abilities.In order to control and optimize the quality of the manufactured part, we need to predict the temperature field throughout the processing of the laminate. In this work, we focus on a thermal modeling of this process which takes in account the imperfect bonding existing between the different layers of the substrate by introducing thermal contact resistance in the model. This study is leaning on experimental results which inform us that the value of the thermal resistance evolves with temperature and pressure applied on the material.

  9. Conventional Tape versus Kinesiotape for Hallux Valgus Correction

    Directory of Open Access Journals (Sweden)

    Nadia Lotfy Radwan

    2017-01-01

    Full Text Available This study was commenced to compare the effect of Kinesiotape (KT versus conventional tape (CT on HVA and IMA as well as the intensity of pain from HV deformity. Methodology: Female patients with age 45 to 60 years and diagnosed with mild to moderate HV were included in the study. The foot pain intensity was assessed by visual analogue scale (VAS before applying tape and after completion of the study. Results: The outcome measures of pain intensity showed a non-significant difference between both groups before intervention (p>0.05. Within both KT and CT groups, the pre-and post-treatment scores were significantly different (p˂0.05. In the comparison of the post treatment scores, there was a significant difference (p˂0.05 between both groups favouring the KT group..

  10. Simulation of magnetization and levitation characteristics of HTS tape stacks

    Science.gov (United States)

    Anischenko, I. V.; Pokrovskii, S. V.; Mineev, N. A.

    2017-12-01

    In this work it is presented a computational model of a magnetic levitation system based on stacks of high-temperature second generation superconducting tapes (HTS) GdBa2Cu3O7-x. Calculated magnetic field and the current distributions in the system for different stacks geometries in the zero-field cooling mode are also presented. The magnetization curves of the stacks in the external field of a permanent NdFeB magnet and the levitation force dependence on the gap between the magnet and the HTS tapes stack were obtained. A model of the magnetic system, oriented to levitation application, is given. Results of modeling were compared with the experimental data.

  11. "The Political Business Cycle: New Evidence from the Nixon Tapes"

    OpenAIRE

    Burton A. Abrams; James L. Butkiewicz

    2011-01-01

    Drawing from the personal tape recordings made during the presidency of Richard Nixon, we uncover and report in this paper new evidence that Nixon manipulated Arthur Burns and the Federal Reserve Bank into creating a political business cycle that helped secure Nixon’s reelection victory in 1972. Nixon understood the risks that his desired monetary policy imposed, but chose to trade longer-term economic costs to the economy for his own short-term political benefit.

  12. El Digital Audio Tape Recorder. Contra autores y creadores

    Directory of Open Access Journals (Sweden)

    Jun Ono

    2015-01-01

    Full Text Available La llamada "DAT" (abreviatura por "digital audio tape recorder" / grabadora digital de audio ha recibido cobertura durante mucho tiempo en los medios masivos de Japón y otros países, como un producto acústico electrónico nuevo y controversial de la industria japonesa de artefactos electrónicos. ¿Qué ha pasado con el objeto de esta controversia?

  13. Modification of critical current in HTSC tape conductors by a ferromagnetic layer

    International Nuclear Information System (INIS)

    Goemoery, F; Souc, J; Seiler, E; Vojenciak, M; Granados, X

    2008-01-01

    In some applications of tape conductors from high temperature superconductors (HTSC) the magnetic field is created by the transported current itself. This is e.g. the case of power transmission cables or current leads. Quite complex distribution of local magnetic field determines then the ability of the superconducting element to carry electrical current. We have investigated how much the critical current of a tape conductor can be changed by putting a ferromagnetic layer in the vicinity of the HTSC material. Numerical procedure has been developed to resolve the current and field distribution in such superconductor-ferromagnet composite tape. Theoretical predictions have been confirmed by experiments on sample made from Bi-2223/Ag composite tape. The critical current of such tape can be improved by placing a soft ferromagnetic material at the tape's edges. On the other hand, the calculations show that the ferromagnetic substrate of YBCO coated tape reduces its self-field critical current

  14. Technical and economical evaluation of tape drip and drip line irrigation systems in a strawberry greenhouse

    Directory of Open Access Journals (Sweden)

    Soghra HOSSEINIAN

    2016-04-01

    Full Text Available This study was done in a strawberry greenhouse to examine the technical and the economical evaluation of two drip irrigation systems including the tape and the drip line in the northern part of Iran. The result showed that all of the technical indices with tape were higher than drip line, and due to statistical analysis reveal a significant difference (P < 0.05. Yield and water productivity (WP with tape were higher than drip line (P < 0.05. Benefit per drop (BPD and net benefit per drop (NBPD with tape were higher than drip line. Net present value, internal rate of capital return and benefit to cost ratio in drip line were higher than tape. In general, regarding technical evaluation tape was better than drip line, besides according to the economical evaluation the drip ­lines were better than tape.

  15. Freshwater Clams (Pilsbryoconcha Exilis) as an Potential Local Mineral Sources in Weaning Food to Overcome Stunting in Grobogan, Central Java, Indonesia

    Science.gov (United States)

    Putri, S. R.; Anjani, Gemala; Wijayanti, Hartanti Sandi; Nuryanto

    2018-02-01

    Based on a preliminary survey in Grobogan Central Java, one of the local food that has a prospective nutrient content developed is freshwater clams. Results of PSG report in 2015, especially in Grobogan district with stunting problem of 31.5% consisting of 7.2% very short and 24.1% short. From the stunting event factor, the role of weaning food in the form of baby porridge is the most important component in the fulfillment of infant nutrition. The research is divided into two stages of the research is the initial stage to make the formulation process by way of freshwater clams, nutrient analysis, and formula calculation. The second stage is the process of formulation weaning food by way of formula making, nutrient analysis, and acceptance test of weaning food on the baby slurry is substituted by the freshwater clams. The influence statistically different substitution of freshwater clams on protein content (p=0.014), fat (p=0,041), carbohydrate (p=0,039), water (p=0,0001), ash (p=0.0001), iron (p=0.0001), and zinc (p=0.0001). There is no influence substitution of freshwater clams on energy content (p=0,129) and fiber (p=0,225). The percentage of favorite level on the acceptance test of color (p=0,005) and taste (p=0,006) was statistically different, but there was no difference flavour (p=0,913) and texture (p=0,198). freshwater clams flour is rich in iron and zinc content, so it can serve as local food, especially in Grobogan Central Java as a stunting handling. Obtained from the results of several formulations substituted of freshwater clams in formulation 2 is a formula that can meet the standards of KEPMENKES except on the content of protein and moisture content. Formula 2 acceptable to the panelists, except for the assessment of taste.

  16. Simulation of YBCO Tape and Coils in HTS Maglev System

    Directory of Open Access Journals (Sweden)

    Song Mengxiao

    2017-01-01

    Full Text Available In the process of running high temperature superconducting maglev train, the AC(Alternating Current loss of superconducting coil is directly related to its safe operation and operating cost. In this paper, the simulation model was built based on the finite element software COMSOL Multiphysics, and mainly simulated and calculated the AC losses of YBCO(Yttrium Barium Copper Oxide tape and coils. In this model, as the solving object, the singular and infinite long YBCO tape and coils model was solved with H-formulation and the nonlinear characteristic (E-J constitutive law and anisotrophy (B-J characteristic were taken into consideration as the theoretical foundation. Then on the basis of the model under maglev suspension system, AC losses under different amplitude and frequence AC currents were calculated. The results shows that under different frequencies and dynamic components, the local maximum AC loss of YBCO tape and coils occurs when the steady-state DC(Direct Current current is 30A. Then comparing with old maglev suspension system, the new system can greatly reduce the energy consumption and the material cost.

  17. Low back pain during pregnancy and Kinesio tape application.

    Science.gov (United States)

    Reyhan, Aycan Çakmak; Dereli, Elif Elçin; Çolak, Tuğba Kuru

    2017-01-01

    Low back pain is a common problem during pregnancy. Although the pain usually occurs in the third trimester, it might be seen in the first trimester, too. There are various types of applications for the treatment of low back pain during pregnancy. However, there is a lack of evidence for the effectiveness of each method. If there is not an obvious deficit, bed rest, exercise, conventional physiotherapy, using protective principles for the lumbar area are recommended, since the main and the only complaint is low back pain. It is aimed in the current review to investigate the use of Kinesio tape in the low back pain seen during pregnancy and to review the literature related to this subject. There are only a few studies investigating the effect of Kinesio tape during pregnancy in the literature and they mostly did not aim to study the low back pain, further evidence and studies are needed to investigate the use of Kinesio tape for the low back pain seen during pregnancy as there is not evidence strong enough. Kinesiotape application aims to increase circulation and mobility, and regarding these gains decreased pain and increased performance are expected.

  18. NdFeB thick films prepared by tape casting

    International Nuclear Information System (INIS)

    Pawlowski, B.; Schwarzer, S.; Rahmig, A.; Toepfer, J.

    2003-01-01

    NdFeB films of thickness between 100 and 800 μm were prepared by tape casting of a slurry containing 84-95 wt% of commercial NdFeB powder (MQP-B, -Q and -S). After curing the flexible green tapes at 120 deg. C non-porous magnetic films are obtained. The remanence of the films is in the range of 350-450 mT and the coercivity is between 300 and 800 kA/m depending on the type of MQP powder used. The magnetic properties of the films are discussed in relation to film composition and type of magnetic material. For MEMS applications the thick films are magnetized with a multi-pole stripe pattern with 1 mm pole pitch. The induction at the surface of the films was measured with a Hall probe and compared to theoretical calculations. The results indicate that the films are completely magnetized regardless of the film thickness. Tape-casted NdFeB thick films are promising candidates for applications in micro-systems or actuators. Miniaturization of the magnet components is one of the key issues in the development of electromagnetic micro-systems, thus creating a need for replacement of small sintered magnets by magnetic thick film components. Other applications include encoders

  19. Electromechanical characterization of superconducting wires and tapes at 77 K

    CERN Document Server

    Bjoerstad, Roger

    The strain dependency of the critical current in state-of-the-art cuprate high-temperature superconductors (HTS) has been characterized. A universal test machine (UTM) combined with a critical current measurement system has been used to characterize the mechanical and the superconducting properties of conductors immersed in an open liquid nitrogen dewar. A set-up has been developed in order to perform simultaneous measurements of the superconductor lattice parameter changes, critical current, as well as the stress and strain at 77 K in self-field in a high energy synchrotron beamline. The HTS tapes and wires studied were based on YBCO, Bi-2223 and Bi-2212. The YBCO tapes were produced by SuperPower and American Superconductors (AMSC). Two types of Bi-2223 tapes, HT and G, were produced by Sumitomo Electric Industries (SEI). The Bi-2212 wires were produced by Oxford Superconducting Technology (OST) using Nexans granulate precursor, before undergoing a specialized over pressure (OP) processing and heat treatmen...

  20. 'Twisted tape sign': Its significance in recurrent sigmoid volvulus

    International Nuclear Information System (INIS)

    Gopal, K.; Lim, Y.; Banerjee, B.

    2005-01-01

    Aim: Sigmoid volvulus is a common cause of intestinal obstruction in the elderly. Mild attacks of sigmoid volvulus may be more difficult to diagnose due to the lack of severity of symptoms which may resolve spontaneously only to recur after an interval. This study was a review of patients to assess the incidence of the 'twisted tape sign' and to evaluate the significance of its presence in cases of recurrent sigmoid volvulus. Methods and materials: A retrospective study over eight years revealed six cases of surgically confirmed recurrent sigmoid volvulus. Case records and barium enemas of all patients were reviewed. Results: Six patients were identified, including four men and two women, with a median age of 56 years. Diagnostic difficulties were encountered in four (67%) patients with a delay ranging between 10 and 37 months with a mean 17.3 months. Twisted tape sign was confirmed on all barium examinations retrospectively. Conclusion: Recognition of twisted tape sign on barium enema examination along with an appropriate clinical history would suggest a diagnosis of recurrent sigmoid volvulus

  1. Thermomechanical Analysis of Shape-Memory Composite Tape Spring

    Science.gov (United States)

    Yang, H.; Wang, L. Y.

    2013-06-01

    Intelligent materials and structures have been extensively applied for satellite designs in order to minimize the mass and reduce the cost in the launch of the spacecraft. Elastic memory composites (EMCs) have the ability of high-strain packaging and shape-memory effect, but increase the parts and total weight due to the additional heating system. Shape-memory sandwich structures Li and Wang (J. Intell. Mater. Syst. Struct. 22(14), 1605-1612, 2011) can overcome such disadvantage by using the metal skin acting as the heating element. However, the high strain in the micro-buckled metal skin decreases the deployment efficiency. This paper aims to present an insight into the folding and deployment behaviors of shape-memory composite (SMC) tape springs. A thermomechanical process was analyzed, including the packaging deformation at an elevated temperature, shape frozen at the low temperature and shape recovery after reheating. The result shows that SMC tape springs can significantly decrease the strain concentration in the metal skin, as well as exhibiting excellent shape frozen and recovery behaviors. Additionally, possible failure modes of SMC tape springs were also analyzed.

  2. Capillary crystallization and molecular-replacement solution of haemoglobin II from the clam Lucina pectinata

    International Nuclear Information System (INIS)

    Gavira, José A.; Jesus, Walleska de; Camara-Artigas, Ana; López-Garriga, Juan; García-Ruiz, Juan M.

    2006-01-01

    The haemoglobin II from the clam L. pectinata has been crystallized using counter-diffusion in single capillary in the presence of agarose to improve crystal quality. Initial phases have been obtained by molecular replacement. Haemoglobin II is one of three haemoglobins present in the cytoplasm of the Lucina pectinata mollusc that inhabits the Caribbean coast. Using HBII purified from its natural source, crystallization screening was performed using the counter-diffusion method with capillaries of 0.2 mm inner diameter. Crystals of HbII suitable for data collection and structure determination were grown in the presence of agarose at 0.1%(w/v) in order to improve their quality. The crystals belong to the tetragonal space group P4 2 2 1 2, with unit-cell parameters a = b = 73.92, c = 152.35 Å, and diffracted X-rays to a resolution of better than 2.0 Å. The asymmetric unit is a homodimer with a corresponding Matthews coefficient (V M ) of 3.15 Å 3 Da −1 and a solvent content of 61% by volume

  3. Is metal contamination responsible for increasing aneuploidy levels in the Manila clam Ruditapes philippinarum?

    KAUST Repository

    Piló, D.

    2016-11-03

    The present study assessed the metal genotoxicity potential at chromosome-level in the bivalve Ruditapes philippinarum collected along different areas of the Tagus estuary. Higher levels of aneuploidy on gill cells were detected at the most sediment contaminated area both in May (31.7%) and October (36.0%) when compared to a less contaminated area over the same periods (20.3% and 29.0% respectively). Interestingly, metal bioaccumulation in gills was higher in the specimens collected at the least contaminated area with the exception of Pb. Indeed, the multivariate analysis revealed a stronger relation between aneuploidy and sediment contamination than between aneuploidy and the bioaccumulation of the metals. The temporal and spatial inconsistency found for the bioaccumulation of metals in R. philippinarum and the positive correlation between sediment contamination and aneuploidy at the most contaminated area suggest that these chromosome-level effects might be due to chronic metal contamination occurring in the Tagus estuary, rather than a direct result of the temporal variation of bioavailable contaminants. The vertical transmission phenomenon of bivalve aneuploidy levels may then be perpetuating those levels on clams from the most contaminated area. The present results shed light about the effect of metal toxicity at the chromosome-level in species inhabiting chronic contaminated areas and highlight the use of aneuploidy as an effective tool to identify persistent contamination in worldwide transitional waters.

  4. Characterization and function of carbonic anhydrases in the zooxanthellae-giant clam symbiosis.

    Science.gov (United States)

    Baillie, B K; Yellowlees, D

    1998-03-22

    Carbonic anhydrase (CA) has been purified from the host tissue of Tridacna gigas, a clam that lives in symbiosis with the dinoflagellate alga, Symbiodinium. At least two isoforms of CA were identified in both gill and mantle tissue. The larger (70 kDa) isoform is a glycoprotein with both N- and O-glycans attached and has highest homology to CAII. It is associated with the membrane fraction while the smaller (32 kDa) is present in the aqueous phase in both tissues. The 32 kDa CA has high homology with mammalian CAI at the N-terminus. Both isoforms cross-reacted with antibodies to CAII from chicken. Immunohistology demonstrated that the 70 kDa CA is present within the ciliated branchial filaments and cells lining the tertiary water channels in the gills of T. gigas. This is consistent with a role in the transport of inorganic carbon (Ci) to the haemolymph and therefore supply of Ci to the zooxanthellae. CA was also detected in mantle epithelial cells where it may also contribute to Ci supply to the zooxanthellae. The hyaline body and nerve tissue in the mantle express the 70 kDa CA where it may be involved in light sensing and nervous transmission.

  5. Overfishing population characteristics of razor clam, Ensis macha, from Independencia Bay, Peru, in 2004 year

    Directory of Open Access Journals (Sweden)

    Juan Tarazona

    2011-05-01

    Full Text Available Quantitative monthly samplings, in 2004, were carried out to estimate the density and biomass of Ensis macha (Molina 1782, from Morro Quemado area, Bay Independence, Pisco. The present study analyzes biometric relationships, growth parameters and somatic production using the ELEFAN I routine and the Crisp’s method. During the year 2004 the rate of exploitation (E= 0.69 y-1 was significantly bigger than the values of 2003 and the monthly landings (maximum of 335 t and fishing effort (maximum of 848 trips were twice increased. These changes induced in the same year a significant decrease of population mean density (D= 54.13 ind. m-2 and the halfway reduction of somatic production (P= 81.99 gAFDW m-2 y-1 and P/B rate (0.38 y-1 values, regarding the values of the previous year. Also, a significant increment of total mortality rate (2.84 y-1 and the fishing mortality rate (1.97 y-1 were twice increased, regarding the previous year. It is assumed that the population of razor clams already was a overfishing commercial resource in the 2003 and that the increment of fishing pressure in the 2004, particularly during the second semester, intensified its overfishing resource condition.

  6. Sterilization of freeze dried manila clam (Ruditapea philippinarum) porridge for immuno-compromised patients

    International Nuclear Information System (INIS)

    Song, Beom Seok; Park, Jae Nam

    2017-01-01

    This study was conducted to evaluate the combined effect of gamma irradiation and different conditions (vacuum packaging, antioxidant and freezing) on the microbiological and sensory characteristics of freeze dried Manila clam porridge (MCP) for immuno-compromised patient food. McP can be sterilized at 1 kGy to 10 kGy. the initial counts of total aerobic bacteria and yeast molds in the non-irradiated MCP were 2.4±0.5 and 1.2±0.3 log CFU g"-'1, respectively, but gamma irradiation significantly decreased the total aerobic bacteria to below the detection limit (1 log CFU g"-"1) (5 kGy). Moreover, gamma irradiation effectively eliminated yeasts/molds at dose below than 1 kGy. However, gamma irradiation accelerated the increase of lipid oxidation and therefore, decreased the sensory characteristics of MCP as irradiation dose increased. to improve the sensory qualities of gamma irradiated MCP, combination treatment (vacuum packaging, 0.1% vitamin c) were applied. there was no significant difference in the overall acceptance scores between the combined-treatment sample (5.6 points) and the non-irradiated samples (6.0). the results indicate that combination treatment (vacuum packaging, 0.1% vitamin c) may help to maintain the quality of MCP. therefore, it considered that irradiation of MCP with combined treatment and this is an effective method for the consumption as a special purpose food such as for space travel or immuno-compromised patients

  7. Morphometry, growth and reproduction of an Atlantic population of the razor clam Ensis macha (Molina, 1782

    Directory of Open Access Journals (Sweden)

    Pedro J. Barón

    2004-06-01

    Full Text Available Ensis macha is a razor clam distributed throughout the coasts of southern Argentina and Chile. Even though it represents a valuable fishery resource, the exploitation of its Atlantic populations has begun only in recent years. This study provides the first estimates of growth rate, an interpretation of the reproductive cycle on the coast of the northern Argentine Patagonia and an analysis of the species morphometry. Growth was estimated by direct observation of growth rings on the valves by two observers. The reproductive cycle was interpreted by the analysis of temporal change of oocyte size frequency distributions. Parameter estimations for the von Bertalanffy equations respectively obtained by observers 1 and 2 were 154 and 153.7 mm for L?, 0.25 and 0.20 yr-1 for k, and -0.08 and -0.72 yr for t0. Two spawning peaks were detected: September-November 1999 and May-June 2000. However, mature females were found all year round. An abrupt change in the relationship between shell length and height was detected at 11.2 mm length.

  8. Preliminary study of HDA coating on CLAM steel followed by high temperature oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Xiaoqiang, E-mail: newboy.chen@163.com; Huang, Qunying; Yan, Zilin; Song, Yong; Liu, Shaojun; Jiang, Zhizhong

    2013-11-15

    A hot-dip aluminizing process is expected to produce aluminide coatings on structural materials to resist tritium permeation, corrosion, and magnetohydrodynamic (MHD) effects in the fusion reactor blanket. China Low Activation Martensitic (CLAM) steel, which is the candidate structural material for the LiPb blanket system in China, was coated with pure aluminum and with an Al–Si alloy. Factors affecting the thickness and morphology of the aluminide coatings were studied. After the hot-dipping treatment, FeAl{sub 3} and Fe{sub 2}Al{sub 5} were observed at the Al/steel interface. The existence of silicon in the molten aluminum suppressed the growth of Fe{sub 2}Al{sub 5}, built up the thickness of FeAl{sub 3} slightly, and contributed to reducing the thickness of the intermetallic layer. The brittle phase of Fe{sub 2}Al{sub 5} had completely transformed to ductile phases of FeAl{sub 2}, FeAl and α-Fe(Al) after high temperature heat-treatment in air. Kirkendall voids were found in the diffusion layer, due to the rapid interdiffusion of iron and aluminum during oxidation. Cracks and pores were observed on the coating surface and at the interlayer. Grazing incidence X-ray diffraction indicates the presence of α-Al{sub 2}O{sub 3} in the oxide layer.

  9. Complement C3 gene: Expression characterization and innate immune response in razor clam Sinonovacula constricta.

    Science.gov (United States)

    Peng, Maoxiao; Niu, Donghong; Wang, Fei; Chen, Zhiyi; Li, Jiale

    2016-08-01

    Complement component 3 (C3) is central to the complement system, playing an important role in immune defense, immune regulation and immune pathology. Several C3 genes have been characterized in invertebrates but very few in shellfish. The C3 gene was identified from the razor clam Sinonovacula constricta, referred to here as Sc-C3. It was found to be highly homologous with the C3 gene of Ruditapes decussatus. All eight model motifs of the C3 gene were found to be included in the thiolester bond and the C345C region. Sc-C3 was widely expressed in all healthy tissues with expression being highest in hemolymph. A significant difference in expression was revealed at the umbo larvae development stage. The expression of Sc-C3 was highly regulated in the hemolymph and liver, with a distinct response pattern being noted after a challenge with Micrococcus lysodeikticus and Vibrio parahemolyticus. It is therefore suggested that a complicated and unique response pathway may be present in S. constricta. Further, serum of S. constricta containing Sc-C3 was extracted. This was activated by LPS or bacterium for verification for function. The more obvious immune function of Sc-C3 was described as an effective membrane rupture in hemocyte cells of rabbit, V. parahemolyticus and Vibrio anguillarum. Thus, Sc-C3 plays an essential role in the immune defense of S. constricta. Copyright © 2016 Elsevier Ltd. All rights reserved.

  10. Development of a Taqman real-time PCR assay for rapid detection and quantification of Vibrio tapetis in extrapallial fluids of clams

    Directory of Open Access Journals (Sweden)

    Adeline Bidault

    2015-12-01

    Full Text Available The Gram-negative bacterium Vibrio tapetis is known as the causative agent of Brown Ring Disease (BRD in the Manila clam Venerupis (=Ruditapes philippinarum. This bivalve is the second most important species produced in aquaculture and has a high commercial value. In spite of the development of several molecular methods, no survey has been yet achieved to rapidly quantify the bacterium in the clam. In this study, we developed a Taqman real-time PCR assay targeting virB4 gene for accurate and quantitative identification of V. tapetis strains pathogenic to clams. Sensitivity and reproducibility of the method were assessed using either filtered sea water or extrapallial fluids of clam injected with the CECT4600T V. tapetis strain. Quantification curves of V. tapetis strain seeded in filtered seawater (FSW or extrapallial fluids (EF samples were equivalent showing reliable qPCR efficacies. With this protocol, we were able to specifically detect V. tapetis strains down to 1.125 101 bacteria per mL of EF or FSW, taking into account the dilution factor used for appropriate template DNA preparation. This qPCR assay allowed us to monitor V. tapetis load both experimentally or naturally infected Manila clams. This technique will be particularly useful for monitoring the kinetics of massive infections by V. tapetis and for designing appropriate control measures for aquaculture purposes.

  11. Nutrients and clam contamination by Escherichia coli in a meso-tidal coastal lagoon: Seasonal variation in counter cycle to external sources

    International Nuclear Information System (INIS)

    Botelho, Maria João; Soares, Florbela; Matias, Domitília; Vale, Carlos

    2015-01-01

    Highlights: • Sources of nutrients and E. coli in Ria Formosa linked to tourism in summer. • Lower nutrient values and clam contamination by E. coli in summer. • Bactericide effect of temperature and solar radiation causes lower E. coli. • Higher biological consumption of nutrients in warmer periods. • Results mirror possible effects of climate changes on coastal lagoons. - Abstract: The clam Ruditapes decussatus was transplanted from a natural recruitment area of Ria Formosa to three sites, surveyed for nutrients in water and sediments. Specimens were sampled monthly for determination of Escherichia coli, condition index and gonadal index. Higher nutrient values in low tide reflect drainage, anthropogenic sources or sediment regeneration, emphasising the importance of water mixing in the entire lagoon driven by the tide. Despite the increase of effluent discharges in summer due to tourism, nutrient concentrations and E. coli in clams were lower in warmer periods. The bactericide effect of temperature and solar radiation was better defined in clams from the inlet channel site than from sites closer to urban effluents. High temperature in summer and torrential freshwater inputs to Ria Formosa may anticipate climate change scenarios for south Europe. Seasonal variation of nutrients and clam contamination may thus point to possible alterations in coastal lagoons and their ecosystem services

  12. Microcystin uptake and biochemical responses in the freshwater clam Corbicula leana P. exposed to toxic and non-toxic Microcystis aeruginosa: Evidence of tolerance to cyanotoxins.

    Science.gov (United States)

    Pham, Thanh-Luu; Shimizu, Kazuya; Dao, Thanh-Son; Hong-Do, Lan-Chi; Utsumi, Motoo

    2015-01-01

    We investigated the accumulation and adverse effects of toxic and non-toxic Microcystis in the edible clam Corbicula leana . Treated clams were exposed to toxic Microcystis at 100 μg of MC (microcystin)-LR eq  L -1 for 10 days. The experimental organism was then placed in toxin-free water and fed on non-toxic Microcystis for the following 10 days for depuration. Filtering rates (FRs) by C. leana of toxic and non-toxic Microcystis and of the green alga Chlorella vulgaris as a control were estimated. Adverse effects were evaluated though the activity of catalase (CAT), superoxide dismutase (SOD) and glutathione S-transferase (GST). Clam accumulated MCs (up to 12.7 ± 2.5 μg g -1 dry weight (DW) of free MC and 4.2 ± 0.6 μg g -1 DW of covalently bound MC). Our results suggest that although both toxic and non-toxic cyanobacteria caused adverse effects by inducing the detoxification and antioxidant defense system, the clam was quite resistant to cyanotoxins. The estimated MC concentration in C. leana was far beyond the World Health Organization's (WHO) provisional tolerable daily intake (0.04 μg kg -1  day -1 ), suggesting that consuming clams harvested during cyanobacterial blooms carries a high health risk.

  13. Microcystin uptake and biochemical responses in the freshwater clam Corbicula leana P. exposed to toxic and non-toxic Microcystis aeruginosa: Evidence of tolerance to cyanotoxins

    Directory of Open Access Journals (Sweden)

    Thanh-Luu Pham

    2015-01-01

    Full Text Available We investigated the accumulation and adverse effects of toxic and non-toxic Microcystis in the edible clam Corbicula leana. Treated clams were exposed to toxic Microcystis at 100 μg of MC (microcystin-LReq L−1 for 10 days. The experimental organism was then placed in toxin-free water and fed on non-toxic Microcystis for the following 10 days for depuration. Filtering rates (FRs by C. leana of toxic and non-toxic Microcystis and of the green alga Chlorella vulgaris as a control were estimated. Adverse effects were evaluated though the activity of catalase (CAT, superoxide dismutase (SOD and glutathione S-transferase (GST. Clam accumulated MCs (up to 12.7 ± 2.5 μg g−1 dry weight (DW of free MC and 4.2 ± 0.6 μg g−1 DW of covalently bound MC. Our results suggest that although both toxic and non-toxic cyanobacteria caused adverse effects by inducing the detoxification and antioxidant defense system, the clam was quite resistant to cyanotoxins. The estimated MC concentration in C. leana was far beyond the World Health Organization's (WHO provisional tolerable daily intake (0.04 μg kg−1 day−1, suggesting that consuming clams harvested during cyanobacterial blooms carries a high health risk.

  14. Enhanced trace element concentrations in tissues of the clam Ruditapes decussatus transplanted to areas influenced by human activities (Ria Formosa, Portugal

    Directory of Open Access Journals (Sweden)

    Maria João Botelho

    2017-06-01

    Full Text Available To examine the extent to which human activities near the Ria Formosa coastal lagoon influence the accumulation of trace elements (TE in Ruditapes decussatus, individuals were transplanted from a natural bank located in the lower lagoon to three sites located in clam growth grounds under the influence of a small city (Faro, a fish farming centre (Olhão and a site near the lagoon inlet (Lavajo. Concentrations were determined in substrate of the clam grounds and in the digestive gland, gills, mantle plus siphons, and remaining tissues of clams in four periods of the year. These measurements were accomplished with the monthly survey of the gametogenic stages, condition index, proteins, glycogen, total lipids, pH and osmolarity of hemolymph. Arsenic, Cu, Mn, V, Cr and Pb were preferentially linked to the digestive gland, while Cd was linked to the gills. TE concentrations in the digestive gland and remaining tissues were higher in winter, most likely reflecting additional inputs associated with rain. The lack of disruptions in biological parameters and the prolonged period of spawning and gonad recovery in clams suggest that the current TE availability in the lagoon has a minor influence on the reproductive cycle and hence on clam production.

  15. Analysis of trace elements in the shells of short-necked clam Ruditapes philippinarum (Mollusca: Bivalvia) with respect to reconstruction of individual life history

    International Nuclear Information System (INIS)

    Arakawa, Jumpei; Sakamoto, Wataru

    1998-01-01

    Strontium (Sr) concentration in the shells of short-necked clams collected at different locations (Shirahama, warm area and Maizuru, cold area, Japan) was analyzed by two methods, PIXE and EPMA. The Sr concentration of external surface of shell umbo, which was made during short term at early benthic phase, was analyzed by PIXE, and was ranged from 1000 to 3500 ppm for individuals. The Sr concentration of clams collected at Shirahama showed positive correlation with shell length (SL) in individuals with SL < 31 mm, whereas clams collected at Maizuru did not show significant correlation. This result may be caused from the difference of the spawning seasons between two areas. The Sr concentration of cross section of shell umbo, which develops thicker continuously during their life to form faint stratum structure, was analyzed by EPMA along the line across the stratum structure. Some surges and long term waving patterns of the Sr concentration were observed. These results suggest that the life histories of individual clams could be recorded in the shell umbo cross sections as variations of trace elements and analyses of trace elements could clarify the histories of individual clams. (author)

  16. Toxicity and the fractional distribution of trace metals accumulated from contaminated sediments by the clam Scrobicularia plana exposed in the laboratory and the field

    Energy Technology Data Exchange (ETDEWEB)

    Kalman, J., E-mail: judit.kalman@uca.es [Department of Life Sciences, The Natural History Museum, Cromwell Road, London SW7 5BD (United Kingdom); Bonnail-Miguel, E. [Department of Physical-Chemistry, University of Cadiz, Poligono Industrial Rio San Pedro s/n, 11,510 Puerto Real, Cadiz (Spain); Smith, B.D. [Department of Life Sciences, The Natural History Museum, Cromwell Road, London SW7 5BD (United Kingdom); Bury, N.R. [Division of Diabetes and Nutritional Science, King' s College London, Franklin-Wilkins Building, 150 Stamford Street, London SE1 9NH (United Kingdom); Rainbow, P.S. [Department of Life Sciences, The Natural History Museum, Cromwell Road, London SW7 5BD (United Kingdom)

    2015-02-15

    The relationship between the subcellular distribution of accumulated toxic metals into five operational fractions (subsequently combined into presumed detoxified and non-detoxified components) and toxicity in the clam Scrobicularia plana was investigated under different laboratory exposures. Clams were exposed to metal contaminated media (water and diet) and analysed for the partitioning of accumulated As, Cu and Zn into subcellular fractions. In general, metallothionein-like proteins, metal-rich granules and cellular debris in different proportions acted as main storage sites of accumulated metals in the clam soft tissues for these three metals. No significant differences were noted in the accumulation rates of As, Cu and Zn of groups of individuals with or without apparent signs of toxicity after up to 30 days of exposure to naturally contaminated sediment mixtures. There was, however, an increased proportional accumulation of Cu in the non-detoxified fraction with increased Cu accumulation rate in the clams, suggesting that the Cu uptake rate from contaminated sediments exceeded the combined rates of elimination and detoxification of Cu, with the subsequent likelihood for toxic effects in the clams. - Highlights: • Scrobicularia plana accumulated As, Cu and Zn from naturally toxic sediments. • Toxic metals were accumulated in detoxified and non-detoxified components. • Cu accumulation in the non-detoxified pool increased with increased Cu uptake rate. • Cu uptake rate exceeded combined loss and detoxification rates to cause toxicity.

  17. Toxicity and the fractional distribution of trace metals accumulated from contaminated sediments by the clam Scrobicularia plana exposed in the laboratory and the field

    International Nuclear Information System (INIS)

    Kalman, J.; Bonnail-Miguel, E.; Smith, B.D.; Bury, N.R.; Rainbow, P.S.

    2015-01-01

    The relationship between the subcellular distribution of accumulated toxic metals into five operational fractions (subsequently combined into presumed detoxified and non-detoxified components) and toxicity in the clam Scrobicularia plana was investigated under different laboratory exposures. Clams were exposed to metal contaminated media (water and diet) and analysed for the partitioning of accumulated As, Cu and Zn into subcellular fractions. In general, metallothionein-like proteins, metal-rich granules and cellular debris in different proportions acted as main storage sites of accumulated metals in the clam soft tissues for these three metals. No significant differences were noted in the accumulation rates of As, Cu and Zn of groups of individuals with or without apparent signs of toxicity after up to 30 days of exposure to naturally contaminated sediment mixtures. There was, however, an increased proportional accumulation of Cu in the non-detoxified fraction with increased Cu accumulation rate in the clams, suggesting that the Cu uptake rate from contaminated sediments exceeded the combined rates of elimination and detoxification of Cu, with the subsequent likelihood for toxic effects in the clams. - Highlights: • Scrobicularia plana accumulated As, Cu and Zn from naturally toxic sediments. • Toxic metals were accumulated in detoxified and non-detoxified components. • Cu accumulation in the non-detoxified pool increased with increased Cu uptake rate. • Cu uptake rate exceeded combined loss and detoxification rates to cause toxicity

  18. Buffer layers grown by replicating the texture of an original template tape

    International Nuclear Information System (INIS)

    Lim, Sunme; Yoo, Jaeun; Park, Chan; Youm, Dojun

    2007-01-01

    We propose a fabrication method of the buffer layers, whose biaxial textures are replicated from an original template tape. The purpose of this method is economical texturing process for coated conductors. At first we prepared a biaxially textured metal tape (TM-tape). Then a sacrifice layer (SA), a buffer layer (BU) and a thick metallic layer (SM) were sequentially deposited on the TM-tape. SA-layer and BU-layer were deposited epitaxially to copy the texture of the TM-tape. SA-layer was dissoluble in water. SM-layer with the textured BU-layer was separated and could be used for a supporting tape for the further growth of a superconducting layer. In this way, it is possible to reuse the original textured TM-tape many times. In this paper, we report the results of our experiments, in which we used a biaxially Ni tape, BaO film, STO film, and a thick Ag film for TM-tape, SA-layer, BU-layer, and SM-layer, respectively. The Ag/STO layers were successfully separated form the Ni tape by dissolving the BaO layer in water. The texture quality of the STO layer was well secured after the separation

  19. Magnetization reversal in an obliquely oriented metal evaporated tape

    International Nuclear Information System (INIS)

    Srinath, S.; Vavassori, P.; Rekveldt, M.Th.; Cook, R.E.; Felcher, G.P.

    2004-01-01

    Magnetization reversal in obliquely oriented metal evaporated videotapes as a function of the tape depth was studied by vector magneto-optic Kerr effect and polarized neutron reflectivity. The magnetization vector was found to rotate coherently out-of-plane by an angle α during the magnetization reversal for a substantial part of the hysteresis cycle. However α differs between the surface-facing and the substrate-facing sides of the film, with the more oxidized surface layer following closely the applied field. Close to M∼0 the film breaks down magnetically into a collage of small domains, reflecting the crystalline microstructure of the material

  20. Electric currents in REBaCuO superconducting tapes

    Czech Academy of Sciences Publication Activity Database

    Jirsa, Miloš; Rameš, Michal; Ďuran, Ivan; Melíšek, T.; Kováč, P.; Viererbl, L.

    2017-01-01

    Roč. 30, č. 4 (2017), 1-8, č. článku 045010. ISSN 0953-2048 EU Projects: European Commission(XE) 633053 - EUROfusion Institutional support: RVO:68378271 ; RVO:61389021 Keywords : superconducting tapes * REBaCuO * critical currents * induction and transport * pinning force density * magnetic relaxation * neutron irradiation Subject RIV: BM - Solid Matter Physics ; Magnetism; BL - Plasma and Gas Discharge Physics (UFP-V) OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.); Fluids and plasma physics (including surface physics) (UFP-V) Impact factor: 2.878, year: 2016

  1. Cache management of tape files in mass storage system

    International Nuclear Information System (INIS)

    Cheng Yaodong; Ma Nan; Yu Chuansong; Chen Gang

    2006-01-01

    This paper proposes the group-cooperative caching policy according to the characteristics of tapes and requirements of high energy physics domain. This policy integrates the advantages of traditional local caching and cooperative caching on basis of cache model. It divides cache into independent groups; the same group of cache is made of cooperating disks on network. This paper also analyzes the directory management, update algorithm and cache consistency of the policy. The experiment shows the policy can meet the requirements of data processing and mass storage in high energy physics domain very well. (authors)

  2. Comparison of self-field effects between Bi-2223/Ag tapes and pancake coils

    International Nuclear Information System (INIS)

    Alamgir, A.K.M.; Gu, C.; Han, Z.

    2005-01-01

    Knowledge on self-field behavior in HTS tape and coil becomes important for the design of HTS devices. We report on the comparative nature and influence of self-field in Bi-2223/Ag tape and pancake coils in terms of critical current and ac loss. Measured dc and ac properties of short tape and pancake coils are verified based on the self-field. It is proved that perpendicular component of self-field acting in opposite direction at the two halves of tape-width determines critical current in short tape and single-turn coil. On the other hand, perpendicular component of self-field pointed in the same direction at the two halves of tape-width determines critical current in multi-turn coils. Influence of magnitude and orientation of self-field on ac loss is also investigated for a series of pancake coils based on the measured self-field ac loss in short sample

  3. Comparison of self-field effects between Bi-2223/Ag tapes and pancake coils

    Energy Technology Data Exchange (ETDEWEB)

    Alamgir, A.K.M. [Applied Superconductivity Research Center, Department of Physics, Tsinghua University, Building Li Zhai, Room 209, Beijing 100084 (China)]. E-mail: alam643@yahoo.com; Gu, C. [Applied Superconductivity Research Center, Department of Physics, Tsinghua University, Building Li Zhai, Room 209, Beijing 100084 (China); Han, Z. [Applied Superconductivity Research Center, Department of Physics, Tsinghua University, Building Li Zhai, Room 209, Beijing 100084 (China)

    2005-08-15

    Knowledge on self-field behavior in HTS tape and coil becomes important for the design of HTS devices. We report on the comparative nature and influence of self-field in Bi-2223/Ag tape and pancake coils in terms of critical current and ac loss. Measured dc and ac properties of short tape and pancake coils are verified based on the self-field. It is proved that perpendicular component of self-field acting in opposite direction at the two halves of tape-width determines critical current in short tape and single-turn coil. On the other hand, perpendicular component of self-field pointed in the same direction at the two halves of tape-width determines critical current in multi-turn coils. Influence of magnitude and orientation of self-field on ac loss is also investigated for a series of pancake coils based on the measured self-field ac loss in short sample.

  4. Modelling of fluid flow in tape casting of thin ceramics: Analytical approaches and numerical investigations

    DEFF Research Database (Denmark)

    Jabbaribehnam, Mirmasoud; Hattel, Jesper Henri

    2016-01-01

    Tape casting has been used to produce thin layers of ceramics that can be used as single layers or can be stacked and laminated into multilayered structures. Many startup products such as multilayered inductors, multilayered varistors, piezoelectrics, ceramic fuel cells and lithium ion battery...... components are dependent upon tape casting technology. One of the growing sciences in the processing of ceramics by tape casting is the use of fluid flow analysis to control and enhance the final tapes. The fluid dynamics analysis of the ceramic slurries during tape casting is an efficient mean to elucidate...... the physical parameters crucial to the process. A review of the development of the tape casting process with particular focus on modelling the material flow is presented and in this context the current status is examined and future potential discussed....

  5. Calibration of Hall sensor array for critical current measurement of YBCO tape with ferromagnetic substrate

    International Nuclear Information System (INIS)

    Zhu, Yunpeng; Wang, Gang; Liu, Liyuan; Yang, Xinsheng; Zhao, Yong

    2015-01-01

    Abstract : HAS (Hall sensor array) is a powerful tool to detect the uniformity of HTS (high temperature superconductor) tape through mapping the distribution of remanent or shielding field along the surface of the tape. However, measurement of HTS tape with ferromagnetic parts by HSA is still an issue because the ferromagnetic substrate has influence on the magnetic field around the HTS layer. In this work, a continuous HSA system has been designed to measure the critical current of the YBCO tape with ferromagnetic substrate. The relationship between the remanent field and critical current was calibrated by the finite element method. The result showed that the HSA is an effective method for evaluating the critical current of the HTS tape with ferromagnetic substrate. - Highlight: • A continuous Hall sensor array system has been designed. • The inhomogeneity of YBCO tape with ferromagnetic substrate can be detected by HAS. • Finite element method is an effective method for calibrating the remanent field.

  6. PERFORMANCE CHARACTERISTICS OF PARABOLIC SOLAR COLLECTOR WATER HEATER SYSTEM FITTED WITH NAIL TWISTED TAPES ABSORBER

    Directory of Open Access Journals (Sweden)

    K. SYED JAFAR

    2017-03-01

    Full Text Available In this paper, the experimental heat transfer, friction loss and thermal performance data for water flowing through the absorber tube fitted with two different twisted tape configurations in parabolic trough collector (PTC are presented. In the present work, a relative experimental study is carried out to investigate the performance of a PTC influenced by heat transfer through fluidabsorber wall mixing mechanism. The major findings of this experiment show that heat transport enhancement in the nail twisted tape collector perform significantly better than plain twisted tapes and also show that the smallest twisted tape ratio enhances the system performance remarkably maximizing the collector efficiency. The results suggest that the twisted tape and nail twisted tape would be a better option for high thermal energy collection in laminar region of the PTC system.

  7. Calibration of Hall sensor array for critical current measurement of YBCO tape with ferromagnetic substrate

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Yunpeng; Wang, Gang; Liu, Liyuan [Key laboratory of Magnetic levitation Technologies and Maglev Trains (Ministry of Education), Superconductor and New Energy R& D Center, Mail Stop 165#, Southwest Jiaotong University, Chengdu, 610031 (China); Yang, Xinsheng, E-mail: xsyang@swjtu.edu.cn [Key laboratory of Magnetic levitation Technologies and Maglev Trains (Ministry of Education), Superconductor and New Energy R& D Center, Mail Stop 165#, Southwest Jiaotong University, Chengdu, 610031 (China); Zhao, Yong [Key laboratory of Magnetic levitation Technologies and Maglev Trains (Ministry of Education), Superconductor and New Energy R& D Center, Mail Stop 165#, Southwest Jiaotong University, Chengdu, 610031 (China); Superconductivity Research Group, School of Materials Science and Engineering, University of New South Wale, Sydney 2052, NSW (Australia)

    2015-12-15

    Abstract : HAS (Hall sensor array) is a powerful tool to detect the uniformity of HTS (high temperature superconductor) tape through mapping the distribution of remanent or shielding field along the surface of the tape. However, measurement of HTS tape with ferromagnetic parts by HSA is still an issue because the ferromagnetic substrate has influence on the magnetic field around the HTS layer. In this work, a continuous HSA system has been designed to measure the critical current of the YBCO tape with ferromagnetic substrate. The relationship between the remanent field and critical current was calibrated by the finite element method. The result showed that the HSA is an effective method for evaluating the critical current of the HTS tape with ferromagnetic substrate. - Highlight: • A continuous Hall sensor array system has been designed. • The inhomogeneity of YBCO tape with ferromagnetic substrate can be detected by HAS. • Finite element method is an effective method for calibrating the remanent field.

  8. Numerical Modeling of the Side Flow in Tape Casting of a Non-Newtonian Fluid

    DEFF Research Database (Denmark)

    Jabbari, Masoud; Hattel, Jesper Henri

    2013-01-01

    in the tape casting process is modeled numerically with ANSYS FLUENT in combination with an Ostwald-de Waele power law constitutive equation. Based on rheometer experiments, the constants in the Ostwald-de Waele power law are identified for the considered LSM material and applied in the numerical modeling......One of the most common ways used to produce multilayer ceramics (MLC) is tape casting. In this process, the dried tape thickness is of great interest to control the desired products and applications. One of the parameters that influences the final tape thickness is the side flow factor (a) which...... is mostly measured at the end of the process by a volumetric comparison of the tape which flowed outside the casting width to the tape within the casting width. This phenomenon has not been predicted theoretically yet in the literature. In this study, the flow of (La0.85Sr0.15)0.9MnO3 (LSM) slurry...

  9. Leak isolation self-repairing tape for a water storage vessel and piping against holes

    International Nuclear Information System (INIS)

    Nagaya, Kosuke; Sekiguchi, Takahiro; Chen, Zhichao; Murakami, Iwanori

    2007-01-01

    A new type taping for a water storage vessel or piping is presented, in which water leakage is isolated automatically by its self-repairing mechanism against holes. The self-repairing unit (sealant layer) is consisting of three pieces of net with polymer particles inside lattices. Polymer particles, which expand their volume with water, is used for having self-repairing forces. In ordinary tapes, water leaks along the boundary between the tape and the vessel. In order to retain the leak isolation force, this article first discusses a method for making the sealant tape, then develops a method for fixing the sealant to the vessel. The portion of water leakage can be checked on this tape, and the method of detecting the hole or crack portion of the vessel is also presented by using the tape. (author)

  10. Favored use of anti-predator netting (APN) applied for the farming of clams leads to little benefits to industry while increasing nearshore impacts and plastics pollution.

    Science.gov (United States)

    Bendell, L I

    2015-02-15

    An overview of the efficacy of anti-predator netting (APN) used by the shellfish industry is presented. There is little support that the currently favored APN effectively protects farmed clams from predators. Evidence does suggest that APN leads to impacts and pollution. APN is an attractant for predators, e.g., crabs, by providing a refuge within Ulva sp. which attaches onto the surface of APN. APN entrains silt and organic matter and increases sediment temperatures degrading habitat underneath the APN. APN present hazards to fish and wildlife and is a source of plastics to the marine environment. The continued use of ineffective APN does not serve either the environment or industry well, and many of these issues could be addressed through the alternate use of "ancient" technology used by aboriginal people to maintain clam gardens; building of rock walls optimizing the amount of clam habitat thereby increasing numbers without the use of APN. Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Study of the inhomogeneity of critical current under in-situ tensile stress for YBCO tape

    Science.gov (United States)

    Zhu, Y. P.; Chen, W.; Zhang, H. Y.; Liu, L. Y.; Pan, X. F.; Yang, X. S.; Zhao, Y.

    2018-07-01

    A Hall sensor system was used to measure the local critical current of YBCO tape with high spatial resolution under in-situ tensile stress. The hot spot generation and minimum quench energy of YBCO tape, which depended on the local critical current, was calculated through the thermoelectric coupling model. With the increase in tensile stress, the cracks which have different dimensions and critical current degradation arose more frequently and lowered the thermal stability of the YBCO tape.

  12. Ankle Taping Does Not Impair Performance in Jump or Balance Tests

    OpenAIRE

    Abián-Vicén, Javier; Alegre, Luis M.; Fernández-Rodríguez, J. Manuel; Lara, Amador J.; Meana, Marta; Aguado, Xavier

    2008-01-01

    This study aimed to investigate the influence of prophylactic ankle taping on two balance tests (static and dynamic balance) and one jump test, in the push off and the landing phase. Fifteen active young subjects (age: 21.0 ± 4.4 years) without previous ankle injuries volunteered for the study. Each participant performed three tests in two different situations: with taping and without taping. The tests were a counter movement jump, static balance, and a dynamic posturography test. The tests a...

  13. Is Kinesio Taping to Generate Skin Convolutions Effective for Increasing Local Blood Circulation?

    OpenAIRE

    Yang, Jae-Man; Lee, Jung-Hoon

    2018-01-01

    Background It is unclear whether traditional application of Kinesio taping, which produces wrinkles in the skin, is effective for improving blood circulation. This study investigated local skin temperature changes after the application of an elastic therapeutic tape using convolution and non-convolution taping methods (CTM/NCTM). Material/Methods Twenty-eight pain-free men underwent CTM and NCTM randomly applied to the right and left sides of the lower back. Using infrared thermography, skin ...

  14. Control program for punched paper tape for the PDP-8/1 computer

    International Nuclear Information System (INIS)

    German, U.

    1976-01-01

    A program was developed for the PDP-8/1 computer to control the punched paper tape supplied by the measuring instruments. Any departure from the program is detected by an optical reader which stops the tape and displays the error on an accumulator. This program which is suitable for large amounts of data punched on paper tape has been in use at the Beer-Sheva laboratories for detecting errors in the sample changing operation. (B.G.)

  15. Insights into the establishment of the Manila clam on a tidal flat at the southern end of an introduced range in Southern California, USA.

    Directory of Open Access Journals (Sweden)

    Drew M Talley

    Full Text Available Coastal ecosystem modifications have contributed to the spread of introduced species through alterations of historic disturbance regimes and resource availability, and increased propagule pressure. Frequency of occurrence of the Manila clam (Venerupis phillipinarum, Veneridae in Southern California estuaries has increased from absent or sparse to common since the mid-1990s. Potential invasion vectors include seafood sales and aquaculture, and spread from established northern populations over decades. The clam's post-settlement habitat preferences are, however, uncertain in this region. Our project aimed to identify factors associated with established patches of the clam within a bay toward the southern end of this introduced range. During summer 2013, we sampled 10 tidal flat sites in Mission Bay, San Diego; each containing an area with and without hard structure (e.g., riprap, boulders. We measured likely environmental influences (e.g., sediment variables, distance to ocean. Manila clam densities across the bay were most strongly associated with site, where highest densities were located in the northern and/or back halves of the bay; and weakly correlated with lower porewater salinities. Within sites, Manila clam density was enhanced in the presence of hard structure in most sites. Prevailing currents and salinity regimes likely contribute to bay wide distributions, while hard structures may provide suitable microhabitats (refuge from predators and physical stress and larval entrapment within sites. Results provide insights into decisions about future shoreline management efforts. Finally, we identify directions for future study to better understand and therefore predict patterns of establishment of the Manila clam in the southern portion of its introduced range.

  16. Can ecological history influence response to pollutants? Transcriptomic analysis of Manila clam collected in different Venice lagoon areas and exposed to heavy metal.

    Science.gov (United States)

    Milan, Massimo; Matozzo, Valerio; Pauletto, Marianna; Di Camillo, Barbara; Giacomazzo, Matteo; Boffo, Luciano; Binato, Giovanni; Marin, Maria Gabriella; Patarnello, Tomaso; Bargelloni, Luca

    2016-05-01

    Chronic exposure to environmental pollutants can exert strong selective pressures on natural populations, favoring the transmission over generations of traits that enable individuals to survive and thrive in highly impacted environments. The lagoon of Venice is an ecosystem subject to heavy anthropogenic impact, mainly due to the industrial activities of Porto Marghera (PM), which led to a severe chemical contamination of soil, groundwater, and sediments. Gene expression analysis on wild Manila clams collected in different Venice lagoon areas enabled to identify differences in gene expression profiles between clams collected in PM and those sampled in clean areas, and the definition of molecular signatures of chemical stress. However, it remains largely unexplored to which extent modifications of gene expression patterns persists after removing the source of contamination. It is also relatively unknown whether chronic exposure to xenobiotics affects the response to other chemical pollutants. To start exploring such issues, in the present study a common-garden experiment was coupled with transcriptomic analysis, to compare gene expression profiles of PM clams with those of clams collected in the less impacted area of Chioggia (CH) during a period under the same control conditions. Part of the two experimental groups were also exposed to copper for seven days to assess whether different "ecological history" does influence response to such pollutant. The results obtained suggest that the chronic exposure to chemical pollution generated a response at the transcriptional level that persists after removal for the contaminated site. These transcriptional changes are centered on key biological processes, such as defense against either oxidative stress or tissue/protein damage, and detoxification, suggesting an adaptive strategy for surviving in the deeply impacted environment of Porto Marghera. On the other hand, CH clams appeared to respond more effectively to copper

  17. Expression of a symbiosis-specific gene in Symbiodinium type A1 associated with coral, nudibranch and giant clam larvae

    KAUST Repository

    Mies, M.

    2017-05-24

    Symbiodinium are responsible for the majority of primary production in coral reefs and found in a mutualistic symbiosis with multiple animal phyla. However, little is known about the molecular signals involved in the establishment of this symbiosis and whether it initiates during host larval development. To address this question, we monitored the expression of a putative symbiosis-specific gene (H+-ATPase) in Symbiodinium A1 ex hospite and in association with larvae of a scleractinian coral (Mussismilia hispida), a nudibranch (Berghia stephanieae) and a giant clam (Tridacna crocea). We acquired broodstock for each host, induced spawning and cultured the larvae. Symbiodinium cells were offered and larval samples taken for each host during the first 72 h after symbiont addition. In addition, control samples including free-living Symbiodinium and broodstock tissue containing symbionts for each host were collected. RNA extraction and RT-PCR were performed and amplified products cloned and sequenced. Our results show that H+-ATPase was expressed in Symbiodinium associated with coral and giant clam larvae, but not with nudibranch larvae, which digested the symbionts. Broodstock tissue for coral and giant clam also expressed H+-ATPase, but not the nudibranch tissue sample. Our results of the expression of H+-ATPase as a marker gene suggest that symbiosis between Symbiodinium and M. hispida and T. crocea is established during host larval development. Conversely, in the case of B. stephanieae larvae, evidence does not support a mutualistic relationship. Our study supports the utilization of H+-ATPase expression as a marker for assessing Symbiodinium-invertebrate relationships with applications for the differentiation of symbiotic and non-symbiotic associations. At the same time, insights from a single marker gene approach are limited and future studies should direct the identification of additional symbiosis-specific genes, ideally from both symbiont and host.

  18. Coping with seawater acidification and the emerging contaminant diclofenac at the larval stage: A tale from the clam Ruditapes philippinarum.

    Science.gov (United States)

    Munari, Marco; Chemello, Giulia; Finos, Livio; Ingrosso, Gianmarco; Giani, Michele; Marin, Maria G

    2016-10-01

    Seawater acidification could alter the susceptibility of marine organisms to emerging contaminants, such as pharmaceuticals. In this study, the combined effects of seawater acidification and the non-steroidal anti-inflammatory drug diclofenac on survival, growth and oxidative stress-related parameters (catalase activity and lipid peroxidation) in the larvae of the Manila clam Ruditapes philippinarum were investigated for the first time. An experimental flow-through system was set up to carry out a 96-h exposure of clam larvae. Two pH levels (pH 8.0, the control, and pH 7.8, the predicted pH by the end of this century) were tested with and without diclofenac (0.5 μg/L). After 4 days, mortality was dramatically higher under reduced pH, particularly in the presence of diclofenac (62% of the larvae dead). Shell morphology was negatively affected by both acidification and diclofenac from the first day of exposure. The percentage of abnormal larvae was always higher at pH 7.8 than in controls, peaking at 98% in the presence of diclofenac after 96 h. Instead, shell length, shell height or the ratio of these values were only negatively influenced by reduced pH throughout the whole experiment. After 96 h, catalase activity was significantly increased in all larvae kept at pH 7.8, whereas no significant difference in lipid peroxidation was found among the treatments. This study demonstrates a high susceptibility of R. philippinarum larvae to a slight reduction in seawater pH. Furthermore, the results obtained highlight that acidification enhances the sensitivity of clam larvae to environmentally relevant concentrations of diclofenac. Copyright © 2016 Elsevier Ltd. All rights reserved.

  19. Best management strategies for sustainable giant clam fishery in French Polynesia islands: answers from a spatial modeling approach.

    Directory of Open Access Journals (Sweden)

    Simon Van Wynsberge

    Full Text Available The giant clam Tridacna maxima has been largely overexploited in many tropical regions over the past decades, and was therefore listed in appendix II of the Convention of International Trade in Endangered Species (CITES in 1985. In French Polynesia, several atolls and islands harbor the world's highest stocks of giant clams in very shallow and accessible areas, which are therefore highly vulnerable to fishing pressure. The local fishery authority (i.e., Direction des Resources Marines or "DRM" implemented several management schemes in 2002 to control and regulate fishing pressure. However, for further decisions DRM was missing a sensitivity analysis on the effectiveness of the possible management actions. Here, we report on the use of a deterministic Viable Population Analysis (VPA and spatially-explicit age-based population model that simulated the 30-year trajectory of a Tridacna maxima stock under different management approaches. Specifically, given various scenarios of intra-island larval dispersal, we tested which of No-take-Areas (NTAs, rotational closures, size limits, quotas, and restocking schemes would lead to the highest future stocks in Tubuai and Raivavae, two exploited islands of the Austral archipelago. For both islands, stock abundances were estimated in 2004/2010 and 2005/2010 respectively, and natural mortalities were assessed previously only in Tubuai. When compared to field data, the model successfully predicted the 2010 stocks for Tubuai, but proved to be less reliable for Raivavae, where natural mortality rates may well be different from those on Tubuai. For Tubuai, the spatial model suggested that reducing fishing effort (through fixed quotas and banning fishing below the 12 cm size limit (as currently implemented were the most effective management actions to sustain T. maxima populations into the future. Implementing NTAs was of poor effectiveness. NTAs increased giant clam stock inside the protected area, but also

  20. Size dependent bioaccumulation and ecotoxicity of gold nanoparticles in an endobenthic invertebrate: The Tellinid clam Scrobicularia plana

    International Nuclear Information System (INIS)

    Pan Jinfen; Buffet, Pierre-Emmanuel; Poirier, Laurence; Amiard-Triquet, Claude; Gilliland, Douglas; Joubert, Yolaine; Pilet, Paul; Guibbolini, Marielle; Risso de Faverney, Christine; Roméo, Michèle; Valsami-Jones, Eugenia; Mouneyrac, Catherine

    2012-01-01

    Gold nanoparticles (AuNPs) have important technological applications resulting in an increased potential for release to the environment, and a greater possibility of toxicological effects. The marine bivalve Scrobicularia plana was exposed to AuNPs of size 5, 15 and 40 nm during a 16 d laboratory exposure at 100 μg Au L −1 . After exposure to AuNPs forming aggregates (>700 nm), the clams accumulated Au in their soft tissues. Biochemical (biomarkers) and behavioral (burrowing and feeding) responses were investigated. Au NPs were responsible of metallothionein induction (5, 40 nm), increased activities of catalase (15, 40 nm) and superoxide dismutase (40 nm) and of glutathione S-transferase by the three sizes of AuNPs indicating defense against oxidative stress. Exposure to AuNPs impaired burrowing behavior. However, it must be underlined that these effects were observed at a dose much higher than expected in the environment. - Highlights: ► AuNPs were aggregated to a maximum distribution peak at 0.6 μm in seawater. ► Scrobicularia plana accumulated Au with higher accumulation for bigger NPs. ► Induction of MT, CAT, SOD and GST showed oxidative stress in clams. ► TBARS levels advocated no significant oxidative damage in clams. ► Gold is an inert metal, ecotoxic effects are probably due to the nanoparticle form. - AuNPs were aggregated in seawater, Scrobicularia plana accumulated Au with higher accumulation for bigger NPs and increased activities of biomarkers showed oxidative stress.

  1. Bending strain study of Bi-2223/Ag tapes using Hall sensor magnetometry

    International Nuclear Information System (INIS)

    Lahtinen, M.; Paasi, J.; Sarkaniemi, J.; Han, Z.; Freltoft, T.

    1996-01-01

    The influence of room temperature bending on critical current (I c ) of Bi-2223/Ag tapes is studied by Hall sensor magnetometry, four-point method and scanning electron microscopy. Hall sensor magnetometry allows one to assess tape homogeneity and the amount of mechanical damage caused by bending. The microstructure of the Bi-2223 ceramic is found to strongly affect the tape behavior under bending strain. In a tape with moderate I c = 6.1 A at 77 K and a porous ceramic core, crack propagation took place normal to the Ag-ceramic interface, whereas in tapes with dense core, I c above 10 A at 77 K, cracks propagated in the tape plane. In monofilamentary tapes core homogeneity correlated with good bending strain performance. In multifilamentary tapes crack propagation between filaments was prohibited by the Ag matrix, thus leading to enhanced strain tolerance. In the high I c tapes studied, bending to 25 mm radius resulted in 1%--2% I c degradation

  2. Current distribution and enhancement of the engineering critical current density in multifilament Bi-2223 tapes

    DEFF Research Database (Denmark)

    Wang, W.G.; Jensen, M.B.; Kindl, B.

    2000-01-01

    The spatial distribution of the critical current density (Jc) and engineering critical current density (Je) along the tape width direction was studied by a cutting technique on Bi-2223 multifilamentary tapes. In general, an increase of Jc towards the centre of the tape was measured. We attribute...... microstructure with a great amount of secondary phases. Local variation of Jc was measured within the centre segment of the tape. This indicates the influence of other factors on Jc, such as filament shape, connectivity of the filaments, and sausaging. Enhancement of Je has been pursued in which average Je of 12...

  3. The Variation of Interface Formation with Slurry Viscosity Change in Side-By-Side Tape Casting

    DEFF Research Database (Denmark)

    Bulatova, Regina; Jabbari, Masoud; Andersen, Kjeld Bøhm

    Homogenous and flexible adjacently graded tapes were produced by casting the organic-based slurries simultaneously. To develop side-by-side tape casing (SBSTC), the material optimization, modernization of the doctor blade design, and parameters control of such processes as casting, drying, de......-bindering and sintering were studied. Solvent and binder concentrations were varied in order to optimize co-casting flow, as well as the drying and sintering shrinkage. Tapes were evaluated in terms of rheological behavior of the slurries, the green and sintered tape microstructure, the quality of the interface area...

  4. New developments for the investigation of hard X-rays emitted by peeling adhesive tapes.

    Science.gov (United States)

    Krämer, D; Lützenkirchen-Hecht, D; Lühmann, B; Keite-Telgenbüscher, K; Frahm, R

    2013-05-01

    We realized an advanced apparatus for the investigation of emitted X-rays produced by peeling adhesive tape rolls under vacuum conditions. Two stepper motors can unwind and rewind a tape roll, and an additional roller with an optical encoder provides measurement and control of the tape speed. This way reproducible and consecutive experiments are feasible without having to change the tape or break the vacuum. The dependence of the X-ray emission on tape speed, gas pressure, type of adhesive tape, and detector angle has been investigated. The resulting spectra are continuous and span an X-ray energy range of typically 2-60 keV with high intensity. Furthermore, the new apparatus allows the in situ metalization of adhesive tape rolls by a gold sputter source. A significantly increased X-ray emission was observed for adhesive tapes with a metal coating. Thin metal foils have been placed between the tape and the detector, different K- and L-absorption edges could be measured. A considerable enhancement of the emission was achieved under the influence of the magnetic field of an NdFeB permanent magnet.

  5. Rapid prototyping of microfluidic systems using a PDMS/polymer tape composite.

    Science.gov (United States)

    Kim, Jungkyu; Surapaneni, Rajesh; Gale, Bruce K

    2009-05-07

    Rapid prototyping of microfluidic systems using a combination of double-sided tape and PDMS (polydimethylsiloxane) is introduced. PDMS is typically difficult to bond using adhesive tapes due to its hydrophobic nature and low surface energy. For this reason, PDMS is not compatible with the xurography method, which uses a knife plotter and various adhesive coated polymer tapes. To solve these problems, a PDMS/tape composite was developed and demonstrated in microfluidic applications. The PDMS/tape composite was created by spinning it to make a thin layer of PDMS over double-sided tape. Then the PDMS/tape composite was patterned to create channels using xurography, and bonded to a PDMS slab. After removing the backing paper from the tape, a complete microfluidic system could be created by placing the construct onto nearly any substrate; including glass, plastic or metal-coated glass/silicon substrates. The bond strength was shown to be sufficient for the pressures that occur in typical microfluidic channels used for chemical or biological analysis. This method was demonstrated in three applications: standard microfluidic channels and reactors, a microfluidic system with an integrated membrane, and an electrochemical biosensor. The PDMS/tape composite rapid prototyping technique provides a fast and cost effective fabrication method and can provide easy integration of microfluidic channels with sensors and other components without the need for a cleanroom facility.

  6. Methods for tape fabrication of continuous filament composite parts and articles of manufacture thereof

    Science.gov (United States)

    Weisberg, Andrew H

    2013-10-01

    A method for forming a composite structure according to one embodiment includes forming a first ply; and forming a second ply above the first ply. Forming each ply comprises: applying a bonding material to a tape, the tape comprising a fiber and a matrix, wherein the bonding material has a curing time of less than about 1 second; and adding the tape to a substrate for forming adjacent tape winds having about a constant distance therebetween. Additional systems, methods and articles of manufacture are also presented.

  7. Forensic utility of the carbon isotope ratio of PVC tape backings

    Science.gov (United States)

    Stern, L. A.; Thompson, A. H.; Mehltretter, A. H.; McLaskey, V.; Parish, A.; Aranda, R.

    2008-12-01

    Forensic interest in adhesive tapes with PVC-backings (polyvinyl chloride, electrical tapes) derives from their use in construction of improvised explosive devices, drug packaging and in a variety of other illicit activities. Due to the range of physical characteristics and chemical compositions of such tapes, traditional microscopic and chemical analysis of the tape backings and adhesives offer a high degree of discrimination between tapes from different manufacturers and products. To evaluate whether carbon isotope ratios may be able to increase discrimination of electrical tapes, particularly with regards to different tapes of the same product, we assessed the PVC-backings of 87 rolls of black electrical tape for their δ13C values. The adhesive on these tapes was physically removed with hexane, and plasticizers within the PVC tape backings were removed by three-20 minute extractions with chloroform. The δ13C values of the PVC tape backings ranged between -23.8 and -41.5 (‰ V-PDB). The carbon isotopic variation within a product (identical brand and product identification) is significant, based on five products with at least 3 rolls (ranges of 7.4‰ (n=3), 10.0‰ (n=6), 4.2‰ (n=16), 3.8‰ (n=6), and 11.5‰ (n=8), respectively). There was no measurable carbon isotope variation in regards to the following: a) along the length of a roll (4 samples from 1 roll); b) between the center and edge of a strip of tape (1 pair); c) between rolls assumed to be from the same lot of tape (2 pairs); d) between different rolls from the same batch of tape (same product purchased at the same time and place; 5 pairs); and e) between samples of a tape at room temperature, heated to 50° C and 80° C for 1 week. For each sample within the population of 87 tapes, carbon isotopes alone exclude 80 to 100% of the tapes as a potential match, with an average exclusion power of 92.5%, using a window of ± 0.4‰. Carbon isotope variations originate from variations in starting

  8. Early development, survival and growth rates of the giant clam Tridacna crocea (Bivalvia: Tridacnidae

    Directory of Open Access Journals (Sweden)

    Miguel Mies

    2012-06-01

    Full Text Available Tridacnid clams are conspicuous inhabitants of Indo-Pacific coral reefs and are traded and cultivated for the aquarium and food industries. In the present study, daily growth rates of larvae of the giant clam Tridacna crocea were determined in the laboratory during the first week of life. Adults were induced to spawn via intra-gonadal serotonin injection through the byssal orifice. After spawning oocytes were collected, fertilized and kept in 3 L glass beakers and raceways treated with antibiotics to avoid culture contamination. Larvae were fed twice with the microalga Isochrysis galbana and zooxanthellae were also offered twice during the veliger stage (days 4 and 6. Larval length was measured using a digitizing tablet coupled to a microcomputer. Larval mortality was exponential during the first 48 hours of life declining significantly afterwards. Mean growth rate was 11.3 μm day-1, increasing after addition of symbionts to 18.0 μm day-1. Survival increased to ca. 75% after the addition of zooxanthellae. The results describe the growth curve for T. crocea larvae and suggest that the acquisition of symbionts by larvae may be useful for larval growth and survival even before larvae have attained metamorphosis.Bivalves tridacnídeos são habitantes conspícuos dos recifes da região do Indo-Pacífico e são cultivados e comercializados para os mercados alimentício e aquarista. No estudo apresentado foram determinadas as taxas de crescimento diário durante a primeira semana de vida da larva do bivalve ornamental Tridacna crocea. As matrizes foram induzidas à desova por meio de uma injeção intragonadal de serotonina realizada através do orifício bissal. Após desova, ovócitos foram coletados, fertilizados e mantidos em béqueres de vidro e tanques de fluxo contínuo tratados com antibióticos para evitar contaminação. Larvas foram alimentadas em duas ocasiões com a microalga Isochrysis galbana e zooxantelas foram oferecidas também por

  9. Settlement, mortality and growth of the asari clam (Ruditapes philippinarum) for a collapsed population on a tidal flat in Nakatsu, Japan

    Science.gov (United States)

    Tezuka, Naoaki; Kamimura, Satomi; Hamaguchi, Masami; Saito, Hajime; Iwano, Hideki; Egashira, Junichi; Fukuda, Yuichi; Tawaratsumida, Takahiko; Nagamoto, Atsushi; Nakagawa, Koichi

    2012-04-01

    Although fluctuation and decline in bivalve populations have been reported worldwide, the underlying processes are not yet fully understood. This lack of understanding is partly due to an absence of demographic information for the early post-settlement period. This is the case particularly for annual production of the asari clam (also commonly known as the Manila clam, Ruditapes philippinarum) in Japan, which has greatly decreased in recent years. A remarkable decrease has been observed in the Nakatsu tidal flat, where current yields are less than 0.02% of the maximum yield. Possible explanations for this decline are: 1. limitation on recruitment due to overfishing; and 2. the demographic processes of growth and mortality have been altered by environmental changes, such as rise in seawater temperature or decrease in phytoplankton abundance. However, because of a lack of demographic information (e.g., the initial densities of larval settlement and mortality and growth rates post-settlement), the reasons for the decline, and the relative importance of each period in the life cycle in determining population abundance, remain unclear. Despite the decline, we observed high levels of recruitment of 0-year-class clams on the Nakatsu tidal flat in spring 2005, where more than 10,000 individuals m- 2 3-5 mm in shell length, estimated to have settled during the previous autumn, were observed. To obtain demographic information on the Nakatsu clams, we investigated two factors. First, we investigated the distribution of the 0-year-class clams and their rate of change in density as a combination of mortality, emigration and immigration on the whole tidal flat after a year. Second, we investigated the rate of change in the density and growth of clams after settlement in the center of the flat for 3 years. The rate of decrease in the density of the 0-year-class clams over the whole tidal flat after a year was greater at the stations where the initial density was higher. This

  10. Comparative bioaccumulation and toxicity of silver in different populations of the intra-sedimentary clam Macoma balthica exposed or not to metal contamination in their natural medium

    International Nuclear Information System (INIS)

    Amiard-Triquet, C.; Geffard, A.; Boisson, F.; Ballan-Dufrancais, C.; Jeantet, A.Y.; Berthet, B.; Mouneyrac, C.

    1999-01-01

    Tolerance to pollutants was observed in living organisms chronically exposed in their environment and detoxification processes have been evoked to explain such observations. In the present study, this hypothesis has been tested in clams originating from an industrialized estuary (Loire, Fr) and from an area submitted only to low anthropogenic influx (Bay of Somme, Fr). The comparison was carried out at different contamination levels in clams exposed to silver (50 to 100 ng Ag.ml -1 till LT 50 when 50% lethality was reached), a metal which has been described as liable to be detoxified through insolubilization and/or binding to metallothionein (MT)

  11. Haemocytic leukemia in Prince Edward Island (PEI) soft shell clam (Mya arenaria): Spatial distribution in agriculturally impacted estuaries

    International Nuclear Information System (INIS)

    Muttray, Annette; Reinisch, Carol; Miller, Jason; Ernst, William; Gillis, Patricia; Losier, Melanie; Sherry, James

    2012-01-01

    Intensive farming of potatoes in Prince Edward Island (PEI) relies on the repeated and widespread application of fertilizers and pesticides. In PEI the main potato farming areas are in close proximity and drain directly to estuaries. Runoff from high agricultural activity watersheds could impact benthic organism health in the depositional zone of downstream estuaries. The estuarine filter feeder Mya arenaria (soft-shell clam) could be particularly vulnerable to both particle-adsorbed and water soluble contaminants. M. arenaria is susceptible to haemocytic leukemia. In May 2009, we established that heavily proliferated leukemia (HPL) prevalence was generally higher in PEI estuaries located downstream of high intensity potato farming (Dunk and Wilmot estuaries) watersheds than in estuaries downstream of lower intensity areas. Using Mab-1E10 based immunocytochemistry we observed that leukemic haemocytes from the Dunk and Wilmot estuaries were 1E10 negative whereas those from the Ox/Sheep estuary (low potato farming intensity) were 1E10 positive. The expression of genes in the p53 tumour suppressor pathway enabled us to differentiate groups of leukemic and normal M. arenaria, validating our diagnoses. In October 2009, we confirmed that HPL prevalence was elevated in the Dunk and Wilmot estuaries compared to reference (Souris River). Moreover, leukemia prevalence declined with distance from the river mouths along transects through the Dunk and Wilmot estuaries. The pesticides ß-endosulfan and α-endosulfan were detected in surface sediments from the Dunk and Wilmot estuaries, but not in sediments from either the Souris River or several other lower intensity potato farming watersheds. Our study provides evidence of an association between intensity of potato farming and prevalence of clam leukemia at downstream estuaries in PEI. - Highlights: ► We examined leukemia prevalence in PEI clams Mya arenaria. ► Prevalence was generally higher downstream of high intensity

  12. Haemocytic leukemia in Prince Edward Island (PEI) soft shell clam (Mya arenaria): Spatial distribution in agriculturally impacted estuaries

    Energy Technology Data Exchange (ETDEWEB)

    Muttray, Annette, E-mail: amuttray@rescan.com [Environment Canada, Water Science and Technology Directorate, 867 Lakeshore Road, Burlington, ON, Canada L7R 4A6 (Canada); Reinisch, Carol, E-mail: creinisch@mbl.edu [Visiting Scientist Environment Canada, Water Science and Technology Directorate, 867 Lakeshore Road, Burlington, ON, Canada L7R 4A6 (Canada); Miller, Jason, E-mail: j.miller@ec.gc.ca [Environment Canada, Water Science and Technology Directorate, 867 Lakeshore Road, Burlington, ON, Canada L7R 4A6 (Canada); Ernst, William, E-mail: bill.ernst@ec.gc.ca [Environment Canada, Water Science and Technology Directorate, 45 Alderney Drive, Dartmouth, NS, Canada B2Y 2N6 (Canada); Gillis, Patricia, E-mail: patty.gillis@ec.gc.ca [Environment Canada, Water Science and Technology Directorate, 867 Lakeshore Road, Burlington, ON, Canada L7R 4A6 (Canada); Losier, Melanie, E-mail: melanie.losier@ec.gc.ca [Environment Canada, Atlantic Laboratory for Environmental Testing, Environmental Science Centre, P.O. Box 23005 Moncton, NB, Canada E1A 6S8 (Canada); Sherry, James, E-mail: jim.sherry@ec.gc.ca [Environment Canada, Water Science and Technology Directorate, 867 Lakeshore Road, Burlington, ON, Canada L7R 4A6 (Canada)

    2012-05-01

    Intensive farming of potatoes in Prince Edward Island (PEI) relies on the repeated and widespread application of fertilizers and pesticides. In PEI the main potato farming areas are in close proximity and drain directly to estuaries. Runoff from high agricultural activity watersheds could impact benthic organism health in the depositional zone of downstream estuaries. The estuarine filter feeder Mya arenaria (soft-shell clam) could be particularly vulnerable to both particle-adsorbed and water soluble contaminants. M. arenaria is susceptible to haemocytic leukemia. In May 2009, we established that heavily proliferated leukemia (HPL) prevalence was generally higher in PEI estuaries located downstream of high intensity potato farming (Dunk and Wilmot estuaries) watersheds than in estuaries downstream of lower intensity areas. Using Mab-1E10 based immunocytochemistry we observed that leukemic haemocytes from the Dunk and Wilmot estuaries were 1E10 negative whereas those from the Ox/Sheep estuary (low potato farming intensity) were 1E10 positive. The expression of genes in the p53 tumour suppressor pathway enabled us to differentiate groups of leukemic and normal M. arenaria, validating our diagnoses. In October 2009, we confirmed that HPL prevalence was elevated in the Dunk and Wilmot estuaries compared to reference (Souris River). Moreover, leukemia prevalence declined with distance from the river mouths along transects through the Dunk and Wilmot estuaries. The pesticides ss-endosulfan and {alpha}-endosulfan were detected in surface sediments from the Dunk and Wilmot estuaries, but not in sediments from either the Souris River or several other lower intensity potato farming watersheds. Our study provides evidence of an association between intensity of potato farming and prevalence of clam leukemia at downstream estuaries in PEI. - Highlights: Black-Right-Pointing-Pointer We examined leukemia prevalence in PEI clams Mya arenaria. Black

  13. Bio-accumulation of some trace metals in the short-neck clam Paphia malabarica from Mandovi estuary, Goa

    Digital Repository Service at National Institute of Oceanography (India)

    KrishnaKumari, L.; Kaisary, S.; Rodrigues, V.

    distributed along the coast of Goa and forms an inexpensive and delicious seafood among recorded as Ag/g dry weight in the whole soft tissue was 3.8, 30.3, 13.5, estuary, Goa. Clams were categorised into two groups, 25–35 mm (small size) and 35–40 mm (big size.... Concentration factor was determined as a ratio of mean metal content (dissolved) in water (Ag/l) and that in the soft tissue (Ag/kg wet weight). All the analyses were carried out in duplicate, and the average values are reported in this paper. 3. Results...

  14. Baseline of organotin pollution in fishes, clams, shrimps, squids and crabs collected from the west coast of India

    Digital Repository Service at National Institute of Oceanography (India)

    Jadhav, S.; Bhosale, D.; Bhosle, N.B.

    is available. The present study was planned to assess organotin contamination levels in edible marine organisms collected from the fish markets of Goa, Karwar and Mumbai, the west coast of India. The sampling locations: Goa (15.5ºN, 73.9ºE), Karwar (14.8º... of Karwar is around 36,000 tonnes. Mumbai coast is about 140 km long. Mumbai is among busiest harbours on the west coast of India is known for industrial pollution. The fishes, clams, crabs and squids and shrimps were collected from local fish markets...

  15. Compatibility of CLAM steel weldments with static LiPb alloy at 550 Degree-Sign C

    Energy Technology Data Exchange (ETDEWEB)

    Chen Xizhang, E-mail: kernel.chen@gmail.com [School of Materials Science and Engineering, Jiangsu University, ZhenJiang, Jiangsu 212013 (China); Shen Zheng; Li Peng [School of Materials Science and Engineering, Jiangsu University, ZhenJiang, Jiangsu 212013 (China); Madigan, Bruce [Montana Tech. of University of Montana, Butte, MT 59701 (United States); Huang Yuming; Lei Yucheng [School of Materials Science and Engineering, Jiangsu University, ZhenJiang, Jiangsu 212013 (China); Huang Qunying [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 031 (China); Zhou Jianzhong [School of Mechanical Engineering, Jiangsu University, ZhenJiang, Jiangsu 212013 (China)

    2012-09-15

    Highlights: Black-Right-Pointing-Pointer Corrosion extent of weld zone is higher than that of HAZ. Black-Right-Pointing-Pointer Thick martensite lath and large residual stress lead to higher corrosion rate. Black-Right-Pointing-Pointer Cr on the surface of weld zone decreases by about 50%, W increases slightly. Black-Right-Pointing-Pointer After 500 h and 1000 h of corrosion, weight losses are 0.272 mg/cm{sup 2} and 0.403 mg/cm{sup 2}. Black-Right-Pointing-Pointer With the increasing of corrosion time, the corrosion rate decreases significantly. - Abstract: CLAM steel is considered as a structural material to be used in the Test Blanket Module as a barrier or blanket adjacent to liquid LiPb in fusion reactors. In this paper, CLAM steel is welded by tungsten inert gas (TIG) welding, and the compatibility of the weldment with liquid LiPb is tested. Specimens were corroded in static liquid LiPb, with corrosion times of 500 h and 1000 h, at 550 Degree-Sign C, and the corresponding weight losses are 0.272 mg/cm{sup 2} and 0.403 mg/cm{sup 2} respectively. Also the corrosion rate decreases with increased corrosion time. In the as-welded condition, corrosion resistance of the weld zone is higher than that of the HAZ (Heat Affected Zone). Likely, thick martensite lath and large residual stresses at the welding zone result in higher corrosion rates. The compatibility of CLAM steel weld joints with high temperature liquid LiPb can be improved to some extent through a post-weld tempering process. The surface of the as-welded CLAM steel is uniformly corroded and the concentration of Cr on the surface decreases by about 50% after corrosion. Penetration of LiPb into the matrix is observed for neither the as-welded nor the as-tempered conditions. Influenced by thick martensite lath and large residual stresses, the welded area, especially the weld zone, is easily corroded, therefore it is of primary importance to protect the welded area in the solid blanket of the fusion reactor.

  16. Species Profiles. Life Histories and Environmental Requirements of Coastal Fishes and Invertebrates (Mid-Atlantic). SURF CLAM

    Science.gov (United States)

    1983-10-01

    ter across the vitelline membrane; the Male and female surf clams are identi- innqr germinal vesicle averages 0.79 cal in external appearance, and...Jones et al. ) (1978) reported age-size relationships In laboratcry experiments con- using cut and polished shells (Table ducted •t 21.7 0 C (71 0 F...and Long Island’s south period (4-6 weeks), due to a persist - shore, out. to a depth of 75 m (246 ent southerly flow of air;. and ft), because of the

  17. Magnetic field profiles of NbTi tapes

    International Nuclear Information System (INIS)

    Migliori, A.; Taylor, R.D.; Bartlett, R.D.

    1976-01-01

    Magnetic field profile measurements were performed on stabilized NbTi tapes in zero applied field carrying large transport current densities. Field profile data were taken on large diameter superconducting sample loops at temperatures between 2 0 K and T/sub c/ (about 9.2 0 K) and several persistent currents up to I/sub c/(T), the maximum. The field profiles scaled with current, independent of temperature, at temperatures below 8.5 0 K and were well described by an elliptical shell approximation which left a current-free, field-free central region. Critical state models applied to this self-field situation proved inadequate. Complex profiles produced by trapped flux in the tape loop were described quantitatively by assuming concentric elliptical shells each with a different current density. The maximum current which could be persisted in the loop at each temperature was linear from 4 to 8.5 K. The effective resistance of the superconducting loop including its joint was less than 10 -13 ohms

  18. Eccentric Exercise, Kinesiology Tape, and Balance in Healthy Men.

    Science.gov (United States)

    Hosp, Simona; Folie, Ramona; Csapo, Robert; Hasler, Michael; Nachbauer, Werner

    2017-07-01

      Deficits in balance have been identified as a possible risk factor for knee injuries in athletes. Despite a lack of evidence for its effectiveness, kinesiology tape (KT) is widely used to prevent knee injuries.   To investigate the influence of KT at the knee joint on balance ability in healthy men after eccentric exercise.   Crossover study.   University laboratory.   Twelve young men with no history of lower limb injury volunteered for the study (age = 23.3 ± 2.6 years). All participants were students enrolled in a sports science program.   Participants performed the balance test with and without KT at the knee joint on 2 separate days.   The ability to maintain balance was assessed during a single-legged-stance test using a computerized balance-stability test system. The test was performed before and after 30 minutes of downhill walking on a treadmill.   Eccentric exercise resulted in a deterioration of balance ability, which was attenuated by the use of KT. Further analyses revealed that the effectiveness of KT depended on the participant's balance status, with the preventive effect being greater in participants presenting with poorer baseline balance ability.   Applied to the knee joint, KT counteracted the exercise-related deterioration of balance ability observed when no tape was used. Participants presenting with below-average balance ability received more benefit from KT. By preventing exercise-related impairment of balance ability, KT might help to reduce the risk of sport-associated knee injuries.

  19. Self-field AC losses in Bi-2223 superconducting tapes

    International Nuclear Information System (INIS)

    Mueller, K. H.; Leslie, K.E.

    1996-01-01

    Full text: The self-field AC loss in Bi-2223 silver sheathed tapes for AC currents of up to 100 A was measured at 77 K and frequencies of 60 Hz and 600 Hz using a lock-in amplifier. The frequency dependence indicated a purely hysteretic loss which can be well described in terms of the critical state model for a flat superconducting strip. The only parameter needed to predict the self-field AC loss is the critical current of the critical state. Because the loss voltage is extremely small compared with the inductive voltage, a very high accuracy of the lock-in amplifier phase setting is required. Unlike in loss measurements on cylindrical superconducting samples, in the case of the tape the measuring circuit leads have to be brought out from the surface forming a loop where the changing magnetic field induces an additional voltage. Only if the loop formed by the leads at the voltage tabs is large enough will the apparent power dissipation approach the real AC loss associated with the length of the sample probed

  20. Numerical modeling of laser assisted tape winding process

    Science.gov (United States)

    Zaami, Amin; Baran, Ismet; Akkerman, Remko

    2017-10-01

    Laser assisted tape winding (LATW) has become more and more popular way of producing new thermoplastic products such as ultra-deep sea water riser, gas tanks, structural parts for aerospace applications. Predicting the temperature in LATW has been a source of great interest since the temperature at nip-point plays a key role for mechanical interface performance. Modeling the LATW process includes several challenges such as the interaction of optics and heat transfer. In the current study, numerical modeling of the optical behavior of laser radiation on circular surfaces is investigated based on a ray tracing and non-specular reflection model. The non-specular reflection is implemented considering the anisotropic reflective behavior of the fiber-reinforced thermoplastic tape using a bidirectional reflectance distribution function (BRDF). The proposed model in the present paper includes a three-dimensional circular geometry, in which the effects of reflection from different ranges of the circular surface as well as effect of process parameters on temperature distribution are studied. The heat transfer model is constructed using a fully implicit method. The effect of process parameters on the nip-point temperature is examined. Furthermore, several laser distributions including Gaussian and linear are examined which has not been considered in literature up to now.

  1. Effect of cadmium in the clam Ruditapes decussatus assessed by proteomic analysis

    Energy Technology Data Exchange (ETDEWEB)

    Chora, Suze [University of Algarve, CIMA, Faculty of Marine and Environmental Sciences, Campus de Gambelas, 8000-139 Faro (Portugal); University of Nice-Sophia Antipolis EA 4228 ECOMERS ' Ecosystemes Cotiers Marins et Reponses aux stress' Parc Valrose, BP 71, 06108 Nice cedex 2 (France); Starita-Geribaldi, Mireille [University of Nice-Sophia Antipolis, Laboratory of Oral Microbiology, URE 01., Faculty of Odontology, Pole Universitaire Saint-Jean d' Angely, 24 avenue des Diables Bleus 06357 Nice cedex 4 (France); Guigonis, Jean-Marie [University of Nice-Sophia Antipolis, Plateforme Bernard Rossi - Proteome Metabolome IFR50, Nice, F-06107 (France); Samson, Michel [University of Nice-Sophia Antipolis, Plateforme Bernard Rossi - Proteome Metabolome IFR50, Nice, F-06107 (France); INSERM, Unite 638, Nice, F-06107 (France); Romeo, Michele [University of Nice-Sophia Antipolis EA 4228 ECOMERS ' Ecosystemes Cotiers Marins et Reponses aux stress' Parc Valrose, BP 71, 06108 Nice cedex 2 (France); Bebianno, Maria Joao, E-mail: mbebian@ualg.pt [University of Algarve, CIMA, Faculty of Marine and Environmental Sciences, Campus de Gambelas, 8000-139 Faro (Portugal)

    2009-10-04

    Cadmium, an environmental stressor due to its toxicity, persistence and accumulation in biota, is widespread in the aquatic environment. Cadmium accumulation kinetics have revealed that Ruditapes decussatus has a high affinity to this metal. Proteomics is an effective tool to evaluate the toxic effects of contaminants. The aim of this study was to investigate the Cd effects in the gill and digestive gland of the sentinel species R. decussatus. Protein expression profiles (PEPs) in the clam tissues exposed to Cd (40 {mu}g l{sup -1}, 21 days) were compared to unexposed ones. Cd induces major changes in tissue-specific protein expression profiles in gill and digestive gland. This tissue dependent response results mainly from differences in Cd accumulation, protein inhibition and/or autophagy. An overall decrease of protein spots was detected in both treated tissues, being higher in gill. Some of the spots more drastically altered after pollutants exposure were excised and nine were identified by micro liquid chromatography tandem mass spectrometry (LC-MS/MS). Proteins identified by homology search in databases included: three proteins (8-fold) up-regulated, one down-regulated, four suppressed and one induced. Cd induces major changes in proteins involved in cytoskeletal structure maintenance (muscle-type actin, adductor muscle actin and {beta}-tubulin), cell maintenance (Rab GDP) and metabolism (ALDH and MCAD, both identified by de novo sequencing) suggesting potential energetic change. They provide a valuable knowledge of Cd effects at biochemical and molecular levels in the gill and digestive gland of R. decussatus.

  2. Sterilization of freeze dried manila clam (Ruditapea philippinarum) porridge for immuno-compromised patients

    Energy Technology Data Exchange (ETDEWEB)

    Song, Beom Seok; Park, Jae Nam [Team for Radiation Food Science and Biotechnology, Advanced Radiation Technology Institute, Korea Atomic Energy Research Institute, Jeongeup (Korea, Republic of)

    2017-02-15

    This study was conducted to evaluate the combined effect of gamma irradiation and different conditions (vacuum packaging, antioxidant and freezing) on the microbiological and sensory characteristics of freeze dried Manila clam porridge (MCP) for immuno-compromised patient food. McP can be sterilized at 1 kGy to 10 kGy. the initial counts of total aerobic bacteria and yeast molds in the non-irradiated MCP were 2.4±0.5 and 1.2±0.3 log CFU g{sup -}'1, respectively, but gamma irradiation significantly decreased the total aerobic bacteria to below the detection limit (1 log CFU g{sup -1}) (5 kGy). Moreover, gamma irradiation effectively eliminated yeasts/molds at dose below than 1 kGy. However, gamma irradiation accelerated the increase of lipid oxidation and therefore, decreased the sensory characteristics of MCP as irradiation dose increased. to improve the sensory qualities of gamma irradiated MCP, combination treatment (vacuum packaging, 0.1% vitamin c) were applied. there was no significant difference in the overall acceptance scores between the combined-treatment sample (5.6 points) and the non-irradiated samples (6.0). the results indicate that combination treatment (vacuum packaging, 0.1% vitamin c) may help to maintain the quality of MCP. therefore, it considered that irradiation of MCP with combined treatment and this is an effective method for the consumption as a special purpose food such as for space travel or immuno-compromised patients.

  3. Molecular characteristics of hemoglobins in blood clam and their immune responses to bacterial infection.

    Science.gov (United States)

    Xu, Bin; Zhang, Yanan; Jing, Zhao; Fan, Tingjun

    2017-06-01

    Bivalve hemoglobins have antibacterial activities, while the underlying mechanisms remain poorly understood. In our study, three full-length cDNAs of hemoglobins from blood clam skHbs were obtained, encoding putative polypeptides of 147, 150, and 152 amino acids, respectively. Predicted advanced protein structures showed that the skHbs had amphipathic antibacterial structures, displayed the typical structural characteristics of proteins with globin-like fold containing numerous alpha-helixes, and forming a homodimeric skHbI and a heterotetrameric skHbII complex. After injected with alive and heat-killed Gram-positive bacteria Bacillus subtilis, the mRNA levels of skHbI and skHbII were both significantly upregulated through increasing the expression of peptidoglycan recognition protein-like (PGRP-like) protein and Toll-like receptor (TLR-like) protein induced by peptidoglycan on the surface of the bacteria, but there were no obvious differences in their protein levels. Besides, reactive oxygen species (ROS) was detected to participate in the resistance to B. subtilis. These implied that skHbs could involve in the innate immune responses to Gram-positive bacterial infection directly with their amphipathic structures and indirectly by increasing ROS production through PGRP triggering Toll pathway. In conclusion, our findings reveal the structural characteristics of skHbs and their mechanism against Gram-positive bacteria thereby providing the molecular evidence for fundamental innate antibacterial activities by invoking respiratory proteins. Copyright © 2017 Elsevier B.V. All rights reserved.

  4. [Carbon, nitrogen, and phosphorus budgets of bottom-cultured clam Ruditapes philippinarum].

    Science.gov (United States)

    Zhang, Sheng-li; Zhang, An-guo; Yuan, Xiu-tang; Liang, Bin; Liu, Shu-xi

    2015-04-01

    In order to elucidate the role of bottom-cultured clams in the coastal nutrient cycle, the seasonal filtration, ingestion and biodeposition rates were in situ measured and carbon (C), nitrogen (N) and phosphorus (P) budgets of Ruditapes philippinarum among four seasons were modeled. The results showed that the scope for growth of R. philippinarum in carbon (SFG(C)), nitrogen (SFG(N)), and phosphorus (SFG(P)) all varied significantly among seasons, with the highest values in spring. Meanwhile, SFG(C) was negative in summer, SFG(N) and SFG(P) were always positive throughout the year. The seasonal variations of SFG(C), SFG(N) and SFG(P) were -3.94-49.82 mg C x ind(-1) x d(-1), 0.72-9.49 mg N x ind(-1) x d(-1), and 0.15-3.06 mg P x ind(-1) x d(-1), respectively. The net growth efficiencies in carbon (K(C2)), nitrogen (K(N2)), and phosphorus (K(P2)) also showed a distinct seasonal pattern among seasons, and ranked as K(P2) > K(N2) > K(C2). The C, N, and P budgets illustrated that the R. philippinarum population relatively used more N and P than C for growth and efficiently transferred the pelagic primary production to a higher trophic level. The current study suggested that R. philippinarum bottom-cultured at large scale might play a dominant role in the nutrient cycle of the coastal ecosystem and should be considered as an important ecological component in coastal areas.

  5. A biomineralization study of the Indo-Pacific giant clam Tridacna gigas

    Science.gov (United States)

    Gannon, M. E.; Pérez-Huerta, A.; Aharon, P.; Street, S. C.

    2017-06-01

    The giant clam, Tridacna gigas, is an important faunal component of reef ecosystems of the Indo-Pacific region. In addition to its ecological role, shells of this bivalve species are useful bioarchives for past climate and environmental reconstructions. However, the biomineralization processes involved in shell aragonite deposition are insufficiently understood. Here, we present a study of the shell microstructure of modern specimens from Palm Island, Great Barrier Reef (GBR), Australia, and Huon Peninsula, Papua New Guinea (PNG), using a combination of petrography, scanning electron microscopy, electron backscatter diffraction, Raman spectroscopy and stable carbon isotope ratios. Daily growth increments were recognizable in all specimens through ontogeny, and counting these growth lines provides a robust specimen age estimate. For the internal layers, paired increments of organized aragonitic needles and compact, oblong crystals were recognized in a specimen from PNG, whereas specimens from GBR were composed of shield-like crystals that were not definable at the microscale. The combination of nutrient availability, rainfall and solar irradiance are likely to be the most significant factors controlling shell growth and may explain the observed differences in microstructure. The external layer, identical in all specimens, was composed of dendritic microstructure that is significantly enriched in 13C compared to the internal layer, suggesting different metabolic controls on layer deposition. We propose that the mineralization of the internal and external layers is independent from each other and associated with the activity of specific mantles. Future studies using T. gigas shells as bioarchives should consider the microstructure as it reflects the environment in which the individual lived and the differences in mineralization pathways of internal and external layers.

  6. Highly restricted gene flow and deep evolutionary lineages in the giant clam Tridacna maxima

    Science.gov (United States)

    Nuryanto, A.; Kochzius, M.

    2009-09-01

    The tropical Indo-West Pacific is the biogeographic region with the highest diversity of marine shallow water species, with its centre in the Indo-Malay Archipelago. However, due to its high endemism, the Red Sea is also considered as an important centre of evolution. Currently, not much is known about exchange among the Red Sea, Indian Ocean and West Pacific, as well as connectivity within the Indo-Malay Archipelago, even though such information is important to illuminate ecological and evolutionary processes that shape marine biodiversity in these regions. In addition, the inference of connectivity among populations is important for conservation. This study aims to test the hypothesis that the Indo-Malay Archipelago and the Red Sea are important centres of evolution by studying the genetic population structure of the giant clam Tridacna maxima. This study is based on a 484-bp fragment of the cytochrome c oxidase I gene from 211 individuals collected at 14 localities in the Indo-West Pacific to infer lineage diversification and gene flow as a measure for connectivity. The analysis showed a significant genetic differentiation among sample sites in the Indo-West Pacific (Φst = 0.74, P < 0.001) and across the Indo-Malay Archipelago (Φst = 0.72, P < 0.001), indicating restricted gene flow. Hierarchical AMOVA revealed the highest fixation index (Φct = 0.8, P < 0.001) when sample sites were assigned to the following regions: (1) Red Sea, (2) Indian Ocean and Java Sea, (3) Indonesian throughflow and seas in the East of Sulawesi, and (4) Western Pacific. Geological history as well as oceanography are important factors that shape the genetic structure of T. maxima in the Indo-Malay Archipelago and Red Sea. The observed deep evolutionary lineages might include cryptic species and this result supports the notion that the Indo-Malay Archipelago and the Red Sea are important centres of evolution.

  7. Current evidence does not support the use of Kinesio Taping in clinical practice: a systematic review

    Directory of Open Access Journals (Sweden)

    Patrícia do Carmo Silva Parreira

    2014-03-01

    Full Text Available Questions: Is Kinesio Taping more effective than a sham taping/placebo, no treatment or other interventions in people with musculoskeletal conditions? Is the addition of Kinesio Taping to other interventions more effective than other interventions alone in people with musculoskeletal conditions? Design: Systematic review of randomised trials. Participants: People with musculoskeletal conditions. Intervention: Kinesio Taping was compared with sham taping/placebo, no treatment, exercises, manual therapy and conventional physiotherapy. Outcome measures: Pain intensity, disability, quality of life, return to work, and global impression of recovery. Results: Twelve randomised trials involving 495 participants were included in the review. The effectiveness of the Kinesio Taping was tested in participants with: shoulder pain in two trials; knee pain in three trials; chronic low back pain in two trials; neck pain in three trials; plantar fasciitis in one trial; and multiple musculoskeletal conditions in one trial. The methodological quality of eligible trials was moderate, with a mean of 6.1 points on the 10-point PEDro Scale score. Overall, Kinesio Taping was no better than sham taping/placebo and active comparison groups. In all comparisons where Kinesio Taping was better than an active or a sham control group, the effect sizes were small and probably not clinically significant or the trials were of low quality. Conclusion: This review provides the most updated evidence on the effectiveness of the Kinesio Taping for musculoskeletal conditions. The current evidence does not support the use of this intervention in these clinical populations. PROSPERO registration: CRD42012003436. [Parreira PdCS, Costa LdCM, Hespanhol Junior LC, Lopes AD, Costa LOP (2014 Current evidence does not support the use of Kinesio Taping in clinical practice: a systematic review. Journal of Physiotherapy 60: 31–39

  8. Influence of different cooling rates on the microstructure of the HAZ and welding CCT diagram of CLAM steel

    Energy Technology Data Exchange (ETDEWEB)

    Zheng Shuhui, E-mail: shzheng@ipp.ac.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); Wu Qingsheng [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); Huang Qunying [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); School of Nuclear Science and Technology, University of Science and Technology of China, Hefei, Anhui, 230027 (China); Liu Shaojun; Han Yangyang [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China)

    2011-10-15

    The evolution of microstructure in the weld HAZ (Heat Affected Zone) under welding thermal cycle was simulated by Gleeble-1500. The microstructures and properties of HAZ at different cooling rates were investigated by optical microscopy (OM), scanning electron microscopy (SEM) and microhardness test. The results showed that when the cooling rates ranged from 3600 K/min to 60 K/min, fully martensitic transformations were achieved, and the cooling rates had little influence on the microstructure and microhardness of martensite. The maximum cooling rate to form ferrite was 60 K/min. When the cooling rates ranged from 60 K/min to 1 K/min, the microhardness of the HAZ began to decrease due to the presence of ferrite, and the lath sizes grew up to 0.13-0.15 {mu}m. The critical cooling rate to gain fully ferrite was found to be slower than 1 K/min. The welding CCT diagram of CLAM steel was constructed and it showed that there were ferrite and martensite transformation regions only. The diagram made it possible to predict the microstructures and properties of HAZ and became an important tool to evaluate weldability of CLAM steel.

  9. Influence of different cooling rates on the microstructure of the HAZ and welding CCT diagram of CLAM steel

    International Nuclear Information System (INIS)

    Zheng Shuhui; Wu Qingsheng; Huang Qunying; Liu Shaojun; Han Yangyang

    2011-01-01

    The evolution of microstructure in the weld HAZ (Heat Affected Zone) under welding thermal cycle was simulated by Gleeble-1500. The microstructures and properties of HAZ at different cooling rates were investigated by optical microscopy (OM), scanning electron microscopy (SEM) and microhardness test. The results showed that when the cooling rates ranged from 3600 K/min to 60 K/min, fully martensitic transformations were achieved, and the cooling rates had little influence on the microstructure and microhardness of martensite. The maximum cooling rate to form ferrite was 60 K/min. When the cooling rates ranged from 60 K/min to 1 K/min, the microhardness of the HAZ began to decrease due to the presence of ferrite, and the lath sizes grew up to 0.13-0.15 μm. The critical cooling rate to gain fully ferrite was found to be slower than 1 K/min. The welding CCT diagram of CLAM steel was constructed and it showed that there were ferrite and martensite transformation regions only. The diagram made it possible to predict the microstructures and properties of HAZ and became an important tool to evaluate weldability of CLAM steel.

  10. Development and validation of 89 novel expressed sequence tag-derived microsatellite markers in blood clam, Tegillarca granosa

    Science.gov (United States)

    Teng, Shuangshuang; Fang, Jun; Cai, Yilong; Chai, Xueliang; Xiao, Guoqiang

    2017-06-01

    Blood clam, Tegillarca granosa, is an important shellfish in Chinese mariculture industry. Investigative research in this species, such as genetic linkage mapping, requires a large panel of molecular markers. In present study, a total of 89 polymorphic microsatellite markers were developed in T. granosa using the sequence database of Life Sciences Technology 454 next generation sequencing technology. All 89 loci were characterized in 20 individual clams from a natural population inhabiting Yueqing Gulf, Zhejiang Province, China. The number of alleles per polymorphic locus varied between 2 and 15, while the observed heterozygosity, expected heterozygosity and polymorphic information content varied between 0.000 and 1.000, 0.102 and 0.921, and 0.048 and 0.886, respectively. Of the 89 loci identified, 32 loci deviated significantly from Hardy-Weinberg equilibrium following Bonferroni correction. Thirty nine markers, which were shown to be polymorphic in a full-sibling family, were tested in Mendelian segregations. As expected, 32 loci were co-dominantly segregated in a Mendelian fashion. These novel developed microsatellite markers represent useful research tools for investigation of population genetic structure and genetic diversity in this species.

  11. Histopathological survey of the mussel Mytilus chilensis (Mytilidae and the clam Gari solida (Psammobiidae from southern Chile

    Directory of Open Access Journals (Sweden)

    Florencia Cremonte

    2015-03-01

    Full Text Available A total of 175 specimens of mussels, Mytilus chilensis (Mytilidae, and 56 specimens of clams, Gari solida (Psammobiidae, were collected in natural beds and culture sites of southern Chile. Juvenile mussel specimens (3 cm of maximum length were free of parasites and diseases, whilst the commercial sized populations was parasitized by intracellular inclusions of bacteria-like organisms in the digestive gland epithelium and in the gills, by ciliates in the gills, turbellarians similar to Paravortex (Rhabocoela in the intestine lumen and copepods attached to the gills. In addition, the disseminated neoplasia disease was also present although in low prevalences. In the clam, G. solida, prokariotic inclusions were found in the digestive gland epithelium and bacteria-like organisms in the gills, often encapsulated by haemocytes; oocysts containing up to 8 sporozoites similar to Nematopsis (Apicomplexa in the connective tissue, causing haemocytic infiltration when the intensity of infection was high; ciliates belonging to two different species (one of them similar to Trichodina inhabiting the gills; and a turbellarian similar to Paravortex in the lumen of digestive system without apparent host reaction. The populations of the bivalve species here studied were devoid of serious pathogens.

  12. Conversion of Biowaste Asian Hard Clam (Meretrix lusoria) Shells into White-Emitting Phosphors for Use in Neutral White LEDs.

    Science.gov (United States)

    Chang, Tsung-Yuan; Wang, Chih-Min; Lin, Tai-Yuan; Lin, Hsiu-Mei

    2016-12-02

    The increasing volume and complexity of waste associated with the modern economy poses a serious risk to ecosystems and human health. However, the remanufacturing and recycling of waste into usable products can lead to substantial resource savings. In the present study, clam shell waste was first transformed into pure and well-crystallized single-phase white light-emitting phosphor Ca₉Gd(PO₄)₇:Eu 2+ ,Mn 2+ materials. The phosphor Ca₉Gd(PO₄)₇:Eu 2+ ,Mn 2+ materials were synthesized by the solid-state reaction method and the carbothermic reduction process, and then characterized and analyzed by means of X-ray diffraction (XRD) and photoluminescence (PL) measurements. The structural and luminescent properties of the phosphors were investigated as well. The PL and quantum efficiency measurements showed that the luminescence properties of clam shell-based phosphors were comparable to that of the chemically derived phosphors. Moreover, white light-emitting diodes were fabricated through the integration of 380 nm chips and single-phase white light-emitting phosphors (Ca 0.979 Eu 0.006 Mn 0.015 )₉Gd(PO₄)₇ into a single package of a white light emitting diode (WLED) emitting a neutral white light of 5298 K with color coordinates of (0.337, 0.344).

  13. Conversion of Biowaste Asian Hard Clam (Meretrix lusoria Shells into White-Emitting Phosphors for Use in Neutral White LEDs

    Directory of Open Access Journals (Sweden)

    Tsung-Yuan Chang

    2016-12-01

    Full Text Available The increasing volume and complexity of waste associated with the modern economy poses a serious risk to ecosystems and human health. However, the remanufacturing and recycling of waste into usable products can lead to substantial resource savings. In the present study, clam shell waste was first transformed into pure and well-crystallized single-phase white light-emitting phosphor Ca9Gd(PO47:Eu2+,Mn2+ materials. The phosphor Ca9Gd(PO47:Eu2+,Mn2+ materials were synthesized by the solid-state reaction method and the carbothermic reduction process, and then characterized and analyzed by means of X-ray diffraction (XRD and photoluminescence (PL measurements. The structural and luminescent properties of the phosphors were investigated as well. The PL and quantum efficiency measurements showed that the luminescence properties of clam shell-based phosphors were comparable to that of the chemically derived phosphors. Moreover, white light-emitting diodes were fabricated through the integration of 380 nm chips and single-phase white light-emitting phosphors (Ca0.979Eu0.006Mn0.0159Gd(PO47 into a single package of a white light emitting diode (WLED emitting a neutral white light of 5298 K with color coordinates of (0.337, 0.344.

  14. Effects of LSP on micro-structures and residual stresses in a 4 mm CLAM steel weld joints

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Xizhang, E-mail: chenxizhang@wzu.edu.cn [School of Mechanical and Electrical Engineering, Wenzhou University., Wenzhou 325035 (China); School of Materials Science and Engineering, Jiangsu University, Zhenjiang 212013, Jiangsu (China); Fang, Yuanyuan [School of Materials Science and Engineering, Jiangsu University, Zhenjiang 212013, Jiangsu (China); Zhang, Shuyan; Kelleher, Joe F. [ISIS, Rutherford Appleton Laboratory, Chilton, Didcot OX11 0QX (United Kingdom); Zhou, Jianzhong [School of Mechanical Engineering, Jiangsu University, Zhenjiang 212013, Jiangsu (China)

    2015-05-15

    The effects of laser shock processing (LSP) on the distribution of residual stress and micro-structure of China Low Activation Martensitic (CLAM) steel weldment were investigated via neutron diffraction and optical microscope (OM). A pair of 4 mm CLAM steel plates joined by GTA welding. Special attention is paid to the generation of high level compressive residual stresses introduced by LSP. Residual stress in longitudinal, normal and transversal direction at weldment surface and longitudinal stress through thickness are evaluated via neutron diffraction. Compressive residual stress after LSP occurred at more than 90% areas within the weld joint, it is almost double the areas of compressive stress compare to weldment surface before LSP. The maximum compressive normal residual stress becomes to −183 MPa after LSP from −63 MPa before LSP. The Modification of surface micro-structures including weld zone (WZ), heat affected zone (HAZ) and base metal (BM) are also discussed. Results to date demonstrate that laser shock processing has been a great potential method for the improvement of mechanical performance of components.

  15. Biomonitoring approach with mussel Mytilus galloprovincialis (Lmk) and clam Ruditapes philippinarum (Adams and Reeve, 1850) in the Lagoon of Venice.

    Science.gov (United States)

    Moschino, Vanessa; Delaney, Eugenia; Meneghetti, Francesca; Ros, Luisa Da

    2011-06-01

    Transplanted Mytilus galloprovincialis and native Ruditapes philippinarum were deployed in 10 sampling stations with different pollution impact within the Lagoon of Venice to evaluate the temporal variations and the suitability of the following cytochemical and histochemical biomarkers just as indicators of environmental stress: lysosomal membrane stability, lipofuscins, neutral lipids and lysosome to cytoplasm volume ratio. The physiological status of the organisms was also investigated by determining the survival in air capability and the reburrowing rate (clams). The biological parameters were assessed in June and October. Furthermore, for a better definition of the environmental aspects of the study sites, heavy metal, PAH and PCB concentrations were also evaluated in the sediments. As a whole, the biological responses examined in both species from all the sampling sites showed significant differences between the two seasonal campaigns, only lysosomal membrane stability exhibited less variability. Pollutants in sediments generally showed low-intermediate contamination levels, few hotspots persisting mostly in the inner areas of the lagoon, the most influenced by the industrial zone. Transplanted mussels were more responsive than native clams and the biological responses of both species varied temporally. The range of the spatial variability was always narrow and reflected only partially the broader variability shown by the chemical content in the sediments. In this sense, biological responses seemed to be particularly influenced by the high temporal and spatial heterogeneity that characterise the Lagoon of Venice, as well as most of the transitional environments.

  16. Invasive zebra mussels (Driessena polymorpha) and Asian clams (Corbicula fluminea) survive gut passage of migratory fish species: implications for dispersal

    Science.gov (United States)

    Gatlin, Michael R.; Shoup, Daniel E.; Long, James M.

    2013-01-01

    The introduction and spread of invasive species is of great concern to natural resource managers in the United States. To effectively control the spread of these species, managers must be aware of the multitude of dispersal methods used by the organisms. We investigated the potential for survival through the gut of a migrating fish (blue catfish, Ictalurus furcatus) as a dispersal mechanism for two invasive bivalves: zebra mussel (Driessena polymorpha) and Asian clam (Corbicula fluminea). Blue catfish (N = 62) were sampled over several months from Sooner Lake, Oklahoma, transported to a laboratory and held in individual tanks for 48 h. All fecal material was collected and inspected for live mussels. Survival was significantly related to water temperature in the lake at the time of collection, with no mussels surviving above 21.1 C°, whereas 12 % of zebra mussels (N = 939) and 39 % of Asian clams (N = 408) consumed in cooler water survived gut passage. This research demonstrates the potential for blue catfish to serve as a dispersal vector for invasive bivalves at low water temperatures.

  17. Consequences of an uncertain mass mortality regime triggered by climate variability on giant clam population management in the Pacific Ocean.

    Science.gov (United States)

    Van Wynsberge, Simon; Andréfouët, Serge; Gaertner-Mazouni, Nabila; Remoissenet, Georges

    2018-02-01

    Despite actions to manage sustainably tropical Pacific Ocean reef fisheries, managers have faced failures and frustrations because of unpredicted mass mortality events triggered by climate variability. The consequences of these events on the long-term population dynamics of living resources need to be better understood for better management decisions. Here, we use a giant clam (Tridacna maxima) spatially explicit population model to compare the efficiency of several management strategies under various scenarios of natural mortality, including mass mortality due to climatic anomalies. The model was parameterized by in situ estimations of growth and mortality and fishing effort, and was validated by historical and new in situ surveys of giant clam stocks in two French Polynesia lagoons. Projections on the long run (100 years) suggested that the best management strategy was a decrease of fishing pressure through quota implementation, regardless of the mortality regime considered. In contrast, increasing the minimum legal size of catch and closing areas to fishing were less efficient. When high mortality occurred due to climate variability, the efficiency of all management scenarios decreased markedly. Simulating El Niño Southern Oscillation event by adding temporal autocorrelation in natural mortality rates increased the natural variability of stocks, and also decreased the efficiency of management. These results highlight the difficulties that managers in small Pacific islands can expect in the future in the face of global warming, climate anomalies and new mass mortalities. Copyright © 2017 Elsevier Inc. All rights reserved.

  18. Identification of Angiotensin I-Converting Enzyme Inhibitory Peptides Derived from Enzymatic Hydrolysates of Razor Clam Sinonovacula constricta

    Directory of Open Access Journals (Sweden)

    Yun Li

    2016-06-01

    Full Text Available Angiotensin I-converting enzyme (ACE inhibitory activity of razor clam hydrolysates produced using five proteases, namely, pepsin, trypsin, alcalase, flavourzyme and proteases from Actinomucor elegans T3 was investigated. Flavourzyme hydrolysate showed the highest level of degree of hydrolysis (DH (45.87% followed by A. elegans T3 proteases hydrolysate (37.84% and alcalase (30.55%. The A. elegans T3 proteases was observed to be more effective in generating small peptides with ACE-inhibitory activity. The 3 kDa membrane permeate of A. elegans T3 proteases hydrolysate showed the highest ACE-inhibitory activity with an IC50 of 0.79 mg/mL. After chromatographic separation by Sephadex G-15 gel filtration and reverse phase-high performance liquid chromatography, the potent fraction was subjected to MALDI/TOF-TOF MS/MS for identification. A novel ACE-inhibitory peptide (VQY was identified exhibiting an IC50 of 9.8 μM. The inhibitory kinetics investigation by Lineweaver-Burk plots demonstrated that the peptide acts as a competitive ACE inhibitor. The razor clam hydrolysate obtained by A. elegans T3 proteases could serve as a source of functional peptides with ACE-inhibitory activity for physiological benefits.

  19. Three vibrio-resistance related EST-SSR markers revealed by selective genotyping in the clam Meretrix meretrix.

    Science.gov (United States)

    Nie, Qing; Yue, Xin; Chai, Xueliang; Wang, Hongxia; Liu, Baozhong

    2013-08-01

    The clam Meretrix meretrix is an important commercial bivalve distributed in the coastal areas of South and Southeast Asia. In this study, marker-trait association analyses were performed based on the stock materials of M. meretrix with different vibrio-resistance profile obtained by selective breeding. Forty-eight EST-SSR markers were screened and 27 polymorphic SSRs of them were genotyped in the clam stocks with different resistance to Vibrio parahaemolyticus (11-R and 11-S) and to Vibrio harveyi (09-R and 09-C). Allele frequency distributions of the SSRs among different stocks were compared using Pearson's Chi-square test, and three functional EST-SSR markers (MM959, MM4765 and MM8364) were found to be associated with vibrio-resistance trait. The 140-bp allele of MM959 and 128-bp allele of MM4765 had significantly higher frequencies in resistant groups (11-R and 09-R) than in susceptive/control groups (11-S and 09-C) (P SSR markers were consistent with the three subgroups distinctions. The putative functions of contig959, contig4765 and contig8364 also suggested that the three SSR-involved genes might play important roles in immunity of M. meretrix. All these results supported that EST-SSR markers MM959, MM4765 and MM8364 were associated with vibrio-resistance and would be useful for marker-assisted selection (MAS) in M. meretrix genetic breeding. Copyright © 2013 Elsevier Ltd. All rights reserved.

  20. Synergistic reinforcement of highly oriented poly(propylene) tapes by sepiolite nanoclay

    NARCIS (Netherlands)

    Bilotti, E.; Deng, H.; Zhang, R.; Lu, D.; Bras, W.; Fischer, H.R.; Peijs, T.

    2010-01-01

    This paper reports the properties of highly oriented nanocomposite tapes based on isotactic PP and needle-like sepiolite nanoclay, obtained by a solid state drawing process. The intrinsic 1D character of sepiolite allows its exploitation in 1D objects, such as oriented polymer fibres and tapes,

  1. Properties of PTFE tape as a semipermeable membrane in fluorous reactions

    Directory of Open Access Journals (Sweden)

    Brendon A. Parsons

    2015-06-01

    Full Text Available In a PTFE tape phase-vanishing reaction (PV-PTFE, a delivery tube sealed with PTFE tape is inserted into a vessel which contains the substrate. The reagent diffuses across the PTFE tape barrier into the reaction vessel. PTFE co-polymer films have been found to exhibit selective permeability towards organic compounds, which was affected by the presence of solvents. In this study, we attempted to establish general trends of permeability of PTFE tape to different compounds and to better describe the process of solvent transport in PV-PTFE bromination reactions. Though PTFE tape has been reported as impermeable to some compounds, such as dimethyl phthalate, solvent adsorption to the tape altered its permeability and allowed diffusion through channels of solvent within the PTFE tape. In this case, the solvent-filled pores of the PTFE tape are chemically more akin to the adsorbed solvent rather than to the PTFE fluorous structure. The solvent uptake effect, which was frequently observed in the course of PV-PTFE reactions, can be related to the surface tension of the solvent and the polarity of the solvent relative to the reagent. The lack of pores in bulk PTFE prevents solvents from altering its permeability and, therefore, bulk PTFE is impermeable to most solvents and reagents. However, bromine, which is soluble in liquid fluorous media, diffused through the bulk PTFE. A better understanding of the PTFE phase barrier will make it possible to further optimize the PV-PTFE reaction design.

  2. Final report: High current capacity high temperature superconducting film based tape for high field magnets

    International Nuclear Information System (INIS)

    Ying Xin

    2000-01-01

    The primary goal of the program was to establish the process parameters for the continuous deposition of high quality, superconducting YBCO films on one meter lengths of buffered RABiTS tape using MOCVD and to characterize the potential utility of the resulting tapes in high field magnet applications

  3. Is application of Kinesio tape to treat hyperlordosis more effective on abdominal muscles or hamstrings?

    Directory of Open Access Journals (Sweden)

    Sara Abolahrari Shirazi

    2018-01-01

    Full Text Available Background: Hyperlordosis is defined as an abnormal increase in the lumbar arch of >40°. This study compared two taping techniques include abdominal muscles and hamstrings taping for the treatment of lumbar hyperlordosis. Materials and Methods: The randomized clinical trial was performed in Shiraz, Iran, during June and September 2014. Thirty women aged 20–45 years old with at least 40° lumbar lordosis participated. The women were randomized into two groups (n = 15. Abdominal muscles taping was performed for the first group, whereas the other group underwent hamstrings taping with 30% tension. Lumbar lordosis was measured before, immediately after, and 24 h after taping. The two-way repeated measures analysis of variance was used to compare the two groups for lumbar lordosis angle. Results: No significant differences were detected between the lumbar lordosis angles before and immediately after taping in the two groups (P > 0.05. However, a significant reduction was observed in lordosis angle in the abdominal group and the hamstring group 24 h after taping relative to before intervention (P < 0.01. Conclusion: Taping of the abdominal and hamstring muscles was not effective immediately, whereas it decreased lordosis after 24 h.

  4. Effects of kinesio taping and hot packs on premenstrual syndrome in females.

    Science.gov (United States)

    Choi, Jung-Hyun

    2017-09-01

    [Purpose] This study aimed to evaluate the effects of taping and hot packs on premenstrual syndrome, in an attempt to generate basic data for physical therapy intervention for premenstrual syndrome. [Subjects and Methods] Thirty-two females in their 20s with premenstrual syndrome were randomly assigned to a taping group (n=10), hot pack group (n=11), and taping with hot pack group (n=11). Premenstrual syndrome was assessed using the Menstrual Distress Questionnaire in each participant prior to intervention and was re-assessed after applying kinesio taping and/or hot pack from 10 days before the estimated date of menstruation until the first day of menstruation. [Results] Data revealed that the taping and taping with hot pack groups showed significantly reduced premenstrual syndrome following intervention. In terms of the differences in the Menstrual Distress Questionnaire total score among the groups, the taping with hot pack and hot pack groups showed a significant difference. [Conclusion] These findings indicate that kinesio taping is an easy, non-drug intervention for female college students with premenstrual syndrome.

  5. Elongated grains in cube textured nickel substrate tapes and flat wires

    International Nuclear Information System (INIS)

    Eickemeyer, J; Gueth, A; Holzapfel, B

    2008-01-01

    Cube textured nickel substrate tapes and flat wires with an increased grain aspect ratio were prepared from nickel micro-alloyed with silver plus yttrium and silver, respectively. Whereas the maximum grain aspect ratio for the tapes was about 6, this value reached up to 14 for the flat wires

  6. Effect of crystallization rate of initial alloy on magnetic properties of amorphous tape

    International Nuclear Information System (INIS)

    Roshchin, V.E.; Gribanov, V.P.; Shcherbakov, D.G.; Gun'kin, V.E.

    1994-01-01

    An investigation is made into mechanism and character of cooling rate effect when castings crytallizing on magnetic properties of rapidly quenched amorphous tape of Fe 78 B 12 Si 9 Ni 1 alloy. The increase of cooling rate and holding at heat for superheated melt is shown to result in a rise of Curie point of amorphous tape

  7. Texture gradients in Fe-sheathed ex situ produced MgB2 tapes

    International Nuclear Information System (INIS)

    Lezza, P; Gladyshevskii, R; Abaecherli, V; Fluekiger, R

    2006-01-01

    Superconducting Fe-sheathed MgB 2 monofilamentary tapes have been fabricated by the powder-in-tube technique, varying the particle size of the starting MgB 2 powder and applying either cold or hot rolling during the last deformation process. Measurements of the critical current density J c with the magnetic field applied parallel or perpendicular to the tape surface revealed a pronounced anisotropy for the cold rolled tapes, which was found to increase with increasing particle size and magnetic field strength. The microstructural origin of the J c anisotropy was confirmed by means of x-ray diffraction performed on the filaments after mechanical removal of the sheath. The local texture was studied in a series of diffraction patterns collected at different distances from the filament centre, removing each time some 25 μm of the filament thickness. In the cold rolled tapes, the average orientation of the MgB 2 grains was found to approach a preferred orientation with the crystallographic c-axis perpendicular to the tape surface, near the interface with the sheath; however, the misalignment angle increased towards the centre of the tape. In the hot rolled tapes, for which no J c anisotropy was observed, the grains were found to be approximately randomly oriented. Roughness measurements performed on the side of the Fe sheath in contact with the MgB 2 filament are in agreement with the difference in texture observed for cold and hot rolled tapes

  8. 36 CFR 1275.64 - Reproduction of tape recordings of Presidential conversations.

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Reproduction of tape... § 1275.64 Reproduction of tape recordings of Presidential conversations. (a) To ensure the preservation... locations established by the Archivist in accordance with § 1275.62. (d) The reproduction for members of the...

  9. Effects of Managers’ Work Motivation and Networking Activity on Their Reported Levels of External Red Tape

    NARCIS (Netherlands)

    Torenvlied, R.; Akkerman, A.

    2012-01-01

    This study brings together two perspectives on managers’ reported levels of red tape. The work motivation perspective explains how managers’ characteristics, such as work engagement (alienation) or commitment, affect their reported levels of red tape. The external control perspective explains how

  10. Computer tape library for collective dose assessments in the European Community

    International Nuclear Information System (INIS)

    Jones, J.A.; Kelly, G.N.

    1981-01-01

    A computer tape library has been established which can readily be applied to enable calculations to be made of the collective dose to the population of the European Community from radioactive effluent discharges within the EC. The background to the development of the tape library and details of its contents, method of application and availability are summarised in this note. (author)

  11. Research on resistance characteristics of YBCO tape under short-time DC large current impact

    Science.gov (United States)

    Zhang, Zhifeng; Yang, Jiabin; Qiu, Qingquan; Zhang, Guomin; Lin, Liangzhen

    2017-06-01

    Research of the resistance characteristics of YBCO tape under short-time DC large current impact is the foundation of the developing DC superconducting fault current limiter (SFCL) for voltage source converter-based high voltage direct current system (VSC-HVDC), which is one of the valid approaches to solve the problems of renewable energy integration. SFCL can limit DC short-circuit and enhance the interrupting capabilities of DC circuit breakers. In this paper, under short-time DC large current impacts, the resistance features of naked tape of YBCO tape are studied to find the resistance - temperature change rule and the maximum impact current. The influence of insulation for the resistance - temperature characteristics of YBCO tape is studied by comparison tests with naked tape and insulating tape in 77 K. The influence of operating temperature on the tape is also studied under subcooled liquid nitrogen condition. For the current impact security of YBCO tape, the critical current degradation and top temperature are analyzed and worked as judgment standards. The testing results is helpful for in developing SFCL in VSC-HVDC.

  12. Study on Fabrication of Ni-5 at.%W Tapes for Coated Conductors from Cylinder Ingots

    DEFF Research Database (Denmark)

    Ma, L.; Suo, H. L.; Yue, Zhao

    2015-01-01

    Ni-5 at.%W (Ni5W) tapes with a strong cube texture were fabricated using the RABiTS technique and by starting from cylindrical shaped ingots. In contrast to a conventional cuboid-shaped ingot, a cylinder shaped ingot has no anisotropy along the axial direction and the resulting tape will therefore...

  13. Analytical investigation in bending characteristic of twisted stacked-tape cable conductor

    International Nuclear Information System (INIS)

    Takayasu, Makoto; Chiesa, Luisa

    2015-01-01

    An analytical model to evaluate bending strains of a twisted stack-tape cable (TSTC) conductor has been developed. Through a comparison with experimental results obtained for a soldered 32-tape YBCO TSTC conductor, it has been found that a Perfect-Slip Model (PSM) taking into account the slipping between tapes in a stacked-tape cable during bending gives much better estimation of the bending performance compared to a No-Slip Model (NSM). In the PSM case the tapes can slip so that the internal longitudinal axial strain can be released. The longitudinal strains of compression and tension regions along the tape are balanced in one twist-pitch and cancel out evenly in a long cable. Therefore, in a cable the strains due to bending can be minimized. This is an important advantage of a TSTC conductor. The effect of the cable diameter size on the bending strain is also expected to be minor, and all tapes composing a TSTC conductor have the same strain response under bending, therefore the cable critical current can be characterized from a single tape behaviour. (paper)

  14. Analytical investigation in bending characteristic of twisted stacked-tape cable conductor

    Science.gov (United States)

    Takayasu, Makoto; Chiesa, Luisa

    2015-12-01

    An analytical model to evaluate bending strains of a twisted stack-tape cable (TSTC) conductor has been developed. Through a comparison with experimental results obtained for a soldered 32-tape YBCO TSTC conductor, it has been found that a Perfect-Slip Model (PSM) taking into account the slipping between tapes in a stacked-tape cable during bending gives much better estimation of the bending performance compared to a No-Slip Model (NSM). In the PSM case the tapes can slip so that the internal longitudinal axial strain can be released. The longitudinal strains of compression and tension regions along the tape are balanced in one twist-pitch and cancel out evenly in a long cable. Therefore, in a cable the strains due to bending can be minimized. This is an important advantage of a TSTC conductor. The effect of the cable diameter size on the bending strain is also expected to be minor, and all tapes composing a TSTC conductor have the same strain response under bending, therefore the cable critical current can be characterized from a single tape behaviour.

  15. Numerical and Experimental Investigation of the Electromechanical Behavior of REBCO Tapes

    Science.gov (United States)

    Allen, N. C.; Chiesa, L.; Takayasu, M.

    2015-12-01

    To fully characterize the electromechanical behavior of a Twisted Stacked-Tape Cable (TSTC) it is important to understand the performance of the individual REBCO tapes under various loading conditions. Numerical modeling and experimentation have been used to investigate the electromechanical characteristics of two commercially available REBCO tapes (SuperPower and SuNAM). Tension and combined tension-torsion experiments on single tapes have been continued, from prior preliminary studies, to characterize their critical current behavior and mechanical strength. Additionally, structural finite element analysis was performed on single tapes under tension and combined tension-torsion to investigate the strain dependence of the critical current. The numerical results were compared to the experimental findings for validation. The SuNAM experimental data matched the numerical model very well while the SuperPower tape experienced degradation at lower stress and strain than predicted in the model. The Superpower tape also displayed greater variability in critical current between different samples as compared with the SuNAM tape.

  16. The effect of rigid taping with tension on mechanical displacement of the skin and change in pain perception.

    Science.gov (United States)

    Chen, Shu-Mei; Lo, Sing Kai; Cook, Jill

    2018-04-01

    To investigate the effect of rigid taping that induces mechanical displacement of the skin on pain perception. Single group experiment design with repeated measures. Twenty-three active healthy volunteers (12 men and 11 women) participated in the study. All participants received three different taping procedures: no tape, taping with tension, and taping without tension. The order of three taping conditions was randomised. Skin displacement was measured during taping with tension. A pressure algometer was used to measure the level of pain perception once before taping, and again after each taping condition, in one testing session. The participants were blind to the values of their pressure pain threshold (PPT) during the experimental period. The mean±SD skin displacement in the condition of taping with tension was 2.58±0.49cm. There were significant differences in PPT between taping with tension and taping without tension (mean difference (mean diff)±standard error (SE) 36.43±4.22kPa, p=0.000) and no tape (mean diff±SE 44.31±3.13kPa, p=0.000). No significant difference in PPT between no tape and taping without tension was found (mean diff±SE 7.88±2.83kPa, p=0.067). Taping with tension increases the threshold of pressure pain perception. Therefore, stretch and compression caused by rigid taping with tension could disturb the nociceptive signal transmission and alter pain perception. Copyright © 2017 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

  17. Generation of ultra-sound during tape peeling

    KAUST Repository

    Marston, Jeremy O.; Riker, Paul W.; Thoroddsen, Sigurdur T

    2014-01-01

    We investigate the generation of the screeching sound commonly heard during tape peeling using synchronised high-speed video and audio acquisition. We determine the peak frequencies in the audio spectrum and, in addition to a peak frequency at the upper end of the audible range (around 20 kHz), we find an unexpected strong sound with a high-frequency far above the audible range, typically around 50 kHz. Using the corresponding video data, the origins of the key frequencies are confirmed as being due to the substructure "fracture" bands, which we herein observe in both high-speed continuous peeling motions and in the slip phases for stick-slip peeling motions.

  18. Continuous welding of unidirectional fiber reinforced thermoplastic tape material

    Science.gov (United States)

    Schledjewski, Ralf

    2017-10-01

    Continuous welding techniques like thermoplastic tape placement with in situ consolidation offer several advantages over traditional manufacturing processes like autoclave consolidation, thermoforming, etc. However, still there is a need to solve several important processing issues before it becomes a viable economic process. Intensive process analysis and optimization has been carried out in the past through experimental investigation, model definition and simulation development. Today process simulation is capable to predict resulting consolidation quality. Effects of material imperfections or process parameter variations are well known. But using this knowledge to control the process based on online process monitoring and according adaption of the process parameters is still challenging. Solving inverse problems and using methods for automated code generation allowing fast implementation of algorithms on targets are required. The paper explains the placement technique in general. Process-material-property-relationships and typical material imperfections are described. Furthermore, online monitoring techniques and how to use them for a model based process control system are presented.

  19. Generation of ultra-sound during tape peeling

    KAUST Repository

    Marston, Jeremy O.

    2014-03-21

    We investigate the generation of the screeching sound commonly heard during tape peeling using synchronised high-speed video and audio acquisition. We determine the peak frequencies in the audio spectrum and, in addition to a peak frequency at the upper end of the audible range (around 20 kHz), we find an unexpected strong sound with a high-frequency far above the audible range, typically around 50 kHz. Using the corresponding video data, the origins of the key frequencies are confirmed as being due to the substructure "fracture" bands, which we herein observe in both high-speed continuous peeling motions and in the slip phases for stick-slip peeling motions.

  20. Adhesive tape exfoliation: Why it works for graphene

    Science.gov (United States)

    Bohr, Jakob

    2015-03-01

    Single-crystal graphite can be cleaved by the use of an adhesive tape. This was also the initial route for obtaining graphene, a one-layer thick graphite slab. In this letter a few simple and fun considerations are presented in an attempt to shed some light on why this procedure is successful. In particular on the nature of the surprisingly small number of repetitive steps that are needed in order to obtain a single-layer slab. Two frameworks for exfoliation are investigated: parallel exfoliation involving repetitive simultaneous cleaving, the other, serial exfoliation, which involves the repetitive cleaving of a single chunk of graphite. For both cases, parallel and serial exfoliation, it is investigated how many generations of cleavages are needed. An approximate model with the probability distribution expressed as a simple closed form is presented and compared with the simulations.

  1. Magnetic imaging of superconducting tapes to determine current flow

    Energy Technology Data Exchange (ETDEWEB)

    Brown, G. W. (Geoffrey W.); Hawley, M. E. (Marilyn E.); Foltyn, S. R. (Stephen R.); Mueller, F. M. (Fred M.)

    2001-01-01

    We have developed a magnetic imaging system that uses magnetoresistive read heads from computer hard disk drives to map the transport-current-induced magnetic field at the surface of superconducting tapes at liquid nitrogen temperature. Transport current pathways are determined from the 2-dimensional magnetic field maps using established inversion schemes. We examined the current flow in pulsed-laser-deposited YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} a films patterned on single crystal SrTiO{sub 3} substrates and on a textured yttria-stabilized-zirconia layer deposited on an Inconel ribbon by ion beam assisted deposition. The transport current densities in all cases were consistent with the Critical State Model. For the Inconel-based sample, the transport current density maps have allowed us to observe defects and determine the region that limits the current carrying capacity of the structure.

  2. Evolution of Archival Storage (from Tape to Memory)

    Science.gov (United States)

    Ramapriyan, Hampapuram K.

    2015-01-01

    Over the last three decades, there has been a significant evolution in storage technologies supporting archival of remote sensing data. This section provides a brief survey of how these technologies have evolved. Three main technologies are considered - tape, hard disk and solid state disk. Their historical evolution is traced, summarizing how reductions in cost have helped being able to store larger volumes of data on faster media. The cost per GB of media is only one of the considerations in determining the best approach to archival storage. Active archives generally require faster response to user requests for data than permanent archives. The archive costs have to consider facilities and other capital costs, operations costs, software licenses, utilities costs, etc. For meeting requirements in any organization, typically a mix of technologies is needed.

  3. Effects of low-dye taping on plantar pressure pre and post exercise: an exploratory study.

    LENUS (Irish Health Repository)

    Nolan, Damien

    2009-01-01

    BACKGROUND: Low-Dye taping is used for excessive pronation at the subtalar joint of the foot. Previous research has focused on the tape\\'s immediate effect on plantar pressure. Its effectiveness following exercise has not been investigated. Peak plantar pressure distribution provides an indirect representation of subtalar joint kinematics. The objectives of the study were 1) To determine the effects of Low-Dye taping on peak plantar pressure immediately post-application. 2) To determine whether any initial effects are maintained following exercise. METHODS: 12 asymptomatic subjects participated; each being screened for excessive pronation (navicular drop > 10 mm). Plantar pressure data was recorded, using the F-scan, at four intervals during the testing session: un-taped, baseline-taped, post-exercise session 1, and post-exercise session 2. Each exercise session consisted of a 10-minute walk at a normal pace. The foot was divided into 6 regions during data analysis. Repeated-measures analysis of variance (ANOVA) was used to assess regional pressure variations across the four testing conditions. RESULTS: Reduced lateral forefoot peak plantar pressure was the only significant difference immediately post tape application (p = 0.039). This effect was lost after 10 minutes of exercise (p = 0.036). Each exercise session resulted in significantly higher medial forefoot peak pressure compared to un-taped; (p = 0.015) and (p = 0.014) respectively, and baseline-taped; (p = 0.036) and (p = 0.015) respectively. Medial and lateral rearfoot values had also increased after the second session (p = 0.004), following their non-significant reduction at baseline-taped. A trend towards a medial-to-lateral shift in pressure present in the midfoot immediately following tape application was still present after 20 minutes of exercise. CONCLUSION: Low-Dye tape\\'s initial effect of reduced lateral forefoot peak plantar pressure was lost after a 10-minute walk. However, the tape continued

  4. How life history influences the responses of the clam Scrobicularia plana to the combined impacts of carbamazepine and pH decrease

    International Nuclear Information System (INIS)

    Freitas, Rosa; Almeida, Ângela; Calisto, Vânia; Velez, Cátia; Moreira, Anthony; Schneider, Rudolf J.; Esteves, Valdemar I.; Wrona, Frederick J.; Soares, Amadeu M.V. M.; Figueira, Etelvina

    2015-01-01

    In the present study, the bivalve Scrobicularia plana, collected from two contrasting areas (pristine location and mercury contaminated area), was selected to assess the biochemical alterations imposed by pH decrease, carbamazepine (an antiepileptic) and the combined effect of both stressors. The effects on oxidative stress related biomarkers after 96 h exposure revealed that pH decrease and carbamazepine induced alterations on clams, with greater impacts on individuals from the contaminated area which presented higher mortality, higher lipid peroxidation and higher glutathione S-transferase activity. These results emphasize the risk of extrapolating results from one area to another, since the same species inhabiting different areas may be affected differently when exposed to the same stressors. Furthermore, the results obtained showed that, when combined, the impact of pH decrease and carbamazepine was lower than each stressor acting alone, which could be related to the defence mechanism of valves closure when bivalves are under higher stressful conditions. - Highlights: • Environmentally relevant concentrations of CBZ and pH 7.1 impacted the performance of Scrobicularia plana. • The combination of CBZ and pH 7.1 did not induce higher impacts compared with stressors acting alone. • Clams from a polluted area showed greater alterations than clams collected from an unpolluted area. - pH decrease and carbamazepine induced biochemical alterations on clams (Scrobicularia plana), with greater impacts on individuals from the contaminated area

  5. Age and growth of the sword razor clam Ensis arcuatus in the Ría de Pontevedra (NW Spain): Influence of environmental parameters

    Science.gov (United States)

    Hernández-Otero, A.; Gaspar, M. B.; Macho, G.; Vázquez, E.

    2014-01-01

    The sword razor clam Ensis arcuatus is the most important commercial species of razor clam in Spain, and its fishery in the Ría de Pontevedra (Galicia, NW Spain) is the most productive. Despite the economic importance of this species, information on its biology is scarce. This study reports shell morphometric relationships, age, and growth rates of E. arcuatus in three fishing beds in the Ría de Pontevedra (Brensa, Bueu and Ons, located in respectively the inner, middle and outer zones of the ria), providing the first estimates of growth parameters for the species in the Iberian Peninsula. Growth was estimated by examination of surface growth rings and internal shell microgrowth patterns (acetate peel technique) that proved to be the most suitable method for growth estimate. Growth of E. arcuatus was slower in Bueu (L∞ = 140.4, k = 0.40) followed by Brensa (L∞ = 151.91, k = 0.40) and Ons (L∞ = 172.7, k = 0.33), and the clams reached commercial size in 1.7, 2.3 and 2.8 years in Ons, Brensa and Bueu, respectively. The differences in growth between sites in relation to environmental parameters are evaluated and the implications for the razor clam fishery are discussed.

  6. Tropomyosin and Actin Identified as Major Allergens of the Carpet Clam (Paphia textile and the Effect of Cooking on Their Allergenicity

    Directory of Open Access Journals (Sweden)

    Zailatul Hani Mohamad Yadzir

    2015-01-01

    Full Text Available Objectives. To identify the major allergenic proteins of clam (Paphia textile and to investigate the effect of different cooking methods on the allergenicity of these identified proteins. Methods. Clam protein extracts were separated by denaturing polyacrylamide gel electrophoresis. IgE reactive proteins were then analyzed by immunoblotting with sera from patients with positive skin prick tests (SPT to the raw clam extract. Mass spectrometry was used to identify the major allergenic proteins of this clam. Results. Raw extract showed 12 protein bands (18–150 kDa. In contrast, fewer protein bands were seen in the boiled extract; those ranging from 40 to 150 kDa were denatured. The protein profiles were similarly altered by frying or roasting. The immunoblots of raw and boiled extracts yielded 10 and 2 IgE-binding proteins, respectively. The fried and roasted extracts showed only a single IgE-binding protein at 37 kDa. Mass spectrometry analysis of the 37 and 42 kDa major allergens indicated that these spots were tropomyosin and actin, respectively. Conclusion. The two major allergens of Paphia textile were identified as the thermostable tropomyosin and a new thermolabile allergen actin.

  7. Ecotoxicological and Health Risk Assessment of Polycyclic Aromatic Hydrocarbons (PAHs) in Short-Neck Clam (Paphia undulata) and Contaminated Sediments in Malacca Strait, Malaysia.

    Science.gov (United States)

    Keshavarzifard, Mehrzad; Zakaria, Mohamad Pauzi; Sharifi, Reza

    2017-10-01

    The distribution, sources, and human health risk assessment of polycyclic aromatic hydrocarbons (PAHs) in surface sediment and the edible tissue of short-neck clam (Paphia undulata) from mudflat ecosystem in the west coast of Malaysia were investigated. The concentrations of ∑ 16 PAHs varied from 347.05 to 6207.5 and 179.32 to 1657.5 ng g -1 in sediment and short-neck clam samples, respectively. The calculations of mean PEL quotients (mean-PELQs) showed that the ecological risk of PAHs in the sediment samples was low to moderate-high level, whereas the total health risk through ingestion and dermal contact was considerably high. The PAHs biota sediment accumulation factors data for short-neck clam were obtained in this study, indicating a preferential accumulation of lower molecular weight PAHs. The source apportionment of PAHs in sediment using positive matrix factorization model indicated that the highest contribution to the PAHs was from diesel emissions (30.38%) followed by oil and oil derivate and incomplete coal combustion (23.06%), vehicular emissions (16.43%), wood combustion (15.93%), and natural gas combustion (14.2%). A preliminary evaluation of human health risk using chronic daily intake, hazard index, benzo[a]pyrene-equivalent (BaP eq ) concentration, and the incremental lifetime cancer risk indicated that PAHs in short-neck clam would induce potential carcinogenic effects in the consumers.

  8. AC losses in horizontally parallel HTS tapes for possible wireless power transfer applications

    Science.gov (United States)

    Shen, Boyang; Geng, Jianzhao; Zhang, Xiuchang; Fu, Lin; Li, Chao; Zhang, Heng; Dong, Qihuan; Ma, Jun; Gawith, James; Coombs, T. A.

    2017-12-01

    This paper presents the concept of using horizontally parallel HTS tapes with AC loss study, and the investigation on possible wireless power transfer (WPT) applications. An example of three parallel HTS tapes was proposed, whose AC loss study was carried out both from experiment using electrical method; and simulation using 2D H-formulation on the FEM platform of COMSOL Multiphysics. The electromagnetic induction around the three parallel tapes was monitored using COMSOL simulation. The electromagnetic induction and AC losses generated by a conventional three turn coil was simulated as well, and then compared to the case of three parallel tapes with the same AC transport current. The analysis demonstrates that HTS parallel tapes could be potentially used into wireless power transfer systems, which could have lower total AC losses than conventional HTS coils.

  9. The effect of tape casting operational parameters on the quality of adjacently graded ceramic film

    DEFF Research Database (Denmark)

    Bulatova, Regina; Gudik-Sørensen, Mads; Della Negra, Michela

    2016-01-01

    For small length tape casting of ceramic slurries varying green film thickness is often a problem. To optimise this, the following parameters were investigated: single blade, double blade, using a pump system and a modelled speed change mode have been analysed. Advantages and limitations of every...... method are described here. The tape casting experiments were built to be generic in order to allow the control of various processing conditions. From these results, the single-blade technique was chosen for a study of side-by-side tape casting. The influence of the geometric parameters of partitioning...... the casting tank into chambers, on the quality of graded tape was studied. Tape casting experiments at different speeds and partition tongue lengths in combination with rheological tests revealed that high casting speeds and absence of the partition under the blade are detrimental to the formation...

  10. Characteristics of joint resistance with different kinds of HTS tapes for heater trigger switch

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Je Yull; Park, Young Gun; Lee, Woo Seung; Jo, Hyun Chul; Ko, Tae Kuk [Yonsei University, Seoul (Korea, Republic of); Yoon, Yong Soo [Shin Ansan University, Ansan (Korea, Republic of)

    2014-03-15

    Recently, many researches on the system of superconducting power supply and superconducting magnetic energy storage (SMES) using high temperature superconducting (HTS) tapes has been progressed. Those kinds of superconducting devices use the heater trigger switches that have a control delay problem at moments of heating up and cooling down. One way to reduce the time delay is using a different HTS tape at trigger part. For example, HTS tape having lower critical temperature can reduce time delay of heating up and heating down stage for heater trigger operation. This paper deals with resistances joint with different kinds of HTS tapes which have different properties to verify usefulness of the suggested method. Three kinds of commercial HTS tapes with different specifications are selected as samples and two kinds of solders are used for comparison. Joint is performed with temperature and pressure controllable joint machine and the joint characteristics are analyzed under the repeatable conditions.

  11. Development of a test procedure for cryogenic adhesive tapes; Entwicklung einer Testprozedur fuer kryogene Klebebaender

    Energy Technology Data Exchange (ETDEWEB)

    Funke, Thomas; Haberstroh, Christoph [TU Dresden (Germany). Bitzer-Professur fuer Kaelte-, Kryo- und Kompressorentechnik; Mayrhofer, Robert; Stipsitz, Johannes [RUAG Space GmbH, Wien (Austria)

    2016-07-01

    At cryostats and dewars for lowest temperatures - especially in connection with liquid-helium cooling at around 4 K, as well at the most applications of the superconductivity - often joints and shutters on the base of low-temperature suited adhesive tapes are required. A current method for the thermal isolation of cold surfaces is their covering with highly reflecting aluminium foils, which are fastened by adhesive aluminium tapes. Selection, usage, and reliability estimation of presumably suited adhesive tapes respectively aluminium tapes occurs presently rather heuristically. A corresponding testing apparature for the measurement of the maximal pulling force was developed and tested by means of a series of test measurements. The testing set-up and measurement results for the validation of the measurement concept with adhesive aluminium tapes are presented in this contribution.

  12. Uranium doping and neutron irradiation of Bi-2223 superconduction tapes for improved critical current density

    International Nuclear Information System (INIS)

    Moss, S.D.; Wang, W.G.; Dou, S.X.; Weinstein, R.

    1998-01-01

    It is demonstrated that a combination of neutron irradiation with uranium doping introduce fission tracks through a Bi-2223 tape which act as effective pinning centres, leading to a substantial increase in critical current. Preliminary data suggests that the combination of uranium doping and neutron irradiation produces improved flux pinning in Bi-2223 tapes over neutron irradiation alone. Before irradiation, SEM, DTA and XRD analyses were performed on the tapes. Both before and after irradiation the trapped maximum magnetic flux was measured at 77K. Before neutron irradiation, uranium doping has no effect on critical current. Preliminary SEM data suggested that the uranium is homogeneously distributed throughout the oxide core of the tape. The presence of 2212 and other secondary phases in the doped tapes suggest further refinement of the sintering procedure is necessary. (authors)

  13. POSTOPERATIVE URINARY RETENTION AND EARLY REPOSITION OF TENSION-FREE VAGINAL TAPE

    Directory of Open Access Journals (Sweden)

    Marijan Lužnik

    2003-12-01

    Full Text Available Background. The purpose of this article is to show a possible method of treatment of postoperative urinary retention after an initial tension-free vaginal tape.Methods. From December 1999 to May 2003 we performed one hundred TVT procedures at our department, among them five women had postoperative urinary retention evaluated with catheterization. Revision and reposition of tension-free vaginal tape were performed if retention of urine was over 100 ml.Results. Urinary retention after an initial tension-free vaginal tape was successfully treated by early reposition of tension-free vaginal tape. This resulted in immediate residualfree voiding and continence, which remained unchanged at 6 week and 3 month follow-up.Conclusions. Postoperative urinary retention may be treated by reposition instead of dissection or elongation of the tension-free vaginal tape.

  14. Torsional Properties of TiNi Shape Memory Alloy Tape for Rotary Actuator

    Science.gov (United States)

    Takeda, K.; Tobushi, H.; Mitsui, K.; Nishimura, Y.; Miyamoto, K.

    2012-12-01

    In order to develop novel shape memory actuators, the torsional deformation of a shape memory alloy (SMA) tape and the actuator models driven by the tape were investigated. The results obtained can be summarized as follows. In the SMA tape subjected to torsion, the martensitic transformation appears along both edges of the tape due to elongation of these elements and grows to the central part. The fatigue life in both the pulsating torsion and alternating torsion is expressed by the unified relationship of the dissipated work in each cycle. Based on an opening and closing door model and a solar-powered active blind model, the two-way rotary driving actuator with a small and simple mechanism can be developed by using torsion of the SMA tape.

  15. Evaluation of the MODIS Aerosol Retrievals over Ocean and Land during CLAMS.

    Science.gov (United States)

    Levy, R. C.; Remer, L. A.; Martins, J. V.; Kaufman, Y. J.; Plana-Fattori, A.; Redemann, J.; Wenny, B.

    2005-04-01

    The Chesapeake Lighthouse Aircraft Measurements for Satellites (CLAMS) experiment took place from 10 July to 2 August 2001 in a combined ocean-land region that included the Chesapeake Lighthouse [Clouds and the Earth's Radiant Energy System (CERES) Ocean Validation Experiment (COVE)] and the Wallops Flight Facility (WFF), both along coastal Virginia. This experiment was designed mainly for validating instruments and algorithms aboard the Terra satellite platform, including the Moderate Resolution Imaging Spectroradiometer (MODIS). Over the ocean, MODIS retrieved aerosol optical depths (AODs) at seven wavelengths and an estimate of the aerosol size distribution. Over the land, MODIS retrieved AOD at three wavelengths plus qualitative estimates of the aerosol size. Temporally coincident measurements of aerosol properties were made with a variety of sun photometers from ground sites and airborne sites just above the surface. The set of sun photometers provided unprecedented spectral coverage from visible (VIS) to the solar near-infrared (NIR) and infrared (IR) wavelengths. In this study, AOD and aerosol size retrieved from MODIS is compared with similar measurements from the sun photometers. Over the nearby ocean, the MODIS AOD in the VIS and NIR correlated well with sun-photometer measurements, nearly fitting a one-to-one line on a scatterplot. As one moves from ocean to land, there is a pronounced discontinuity of the MODIS AOD, where MODIS compares poorly to the sun-photometer measurements. Especially in the blue wavelength, MODIS AOD is too high in clean aerosol conditions and too low under larger aerosol loadings. Using the Second Simulation of the Satellite Signal in the Solar Spectrum (6S) radiative code to perform atmospheric correction, the authors find inconsistency in the surface albedo assumptions used by the MODIS lookup tables. It is demonstrated how the high bias at low aerosol loadings can be corrected. By using updated urban/industrial aerosol

  16. Geochemical influences on assimilation of sediment-bound metals in clams and mussels

    Science.gov (United States)

    Griscom, S.B.; Fisher, N.S.; Luoma, S.N.

    2000-01-01

    A series of experiments was performed to evaluate the extent to which Cd, Co, Ag, Se, Cr, and Zn bound to sediments with different geochemical properties could be assimilated by the mussel Mytilus edulis and the clam Macoma balthica. Oxidized and reduced radiolabeled sediments were fed to suspension-feeding animals, the depuration patterns of the individuals were followed by ??-spectrometry, and the assimilation efficiencies (AEs) of ingested metals were determined. AEs from geochemically diverse sediments typically varied less than 2-fold and ranged from 1% for Cr to 42% for Zn. Metals were assimilated from anoxic sediment by both animals; Ag, Cd, and Co AEs in M. balthica were 9-16%, 2-fold lower than from oxic sediment, but in M. edulis AEs were about two times greater from anoxic sediment for all metals but Ag. For oxic sediment, Cd and Co AEs in M. edulis decreased 3-4-fold with increased sediment exposure time to the metals with smaller but significant effects also noted for Zn and Se but not Ag. A less pronounced decrease in AE for M. balthica was evident only after 6 months exposure time. Sequential extractions of the oxidized sediments showed a transfer of metals into more resistant sediment components over time, but the rate did not correlate with a decrease in metal AEs. Comparing the two bivalves, TOC concentrations had an inconsistent effect on metal AEs. AEs of metals from bacteria-coated glass beads were slightly higher than from humic acid-coated beads, which were comparable with whole-sediment AEs. There was correspondence of AE with desorption of Ag, Cd, Co, and Se (but not Zn) from sediments into pH 5 seawater, measured to simulate the gut pH of these bivalves. The results imply that metals associated with sulfides and anoxic sediments are bioavailable, that the bioavailability of metals from sediments decreases over exposure time, that organic carbon content generally has a small effect on AEs, and that AEs of sediment-bound metals differ among

  17. Certification of Trace Elements and Methyl Mercury Mass Fractions in IAEA-461 Clam (Gafrarium tumidum) Sample

    International Nuclear Information System (INIS)

    2016-01-01

    The primary goal of the IAEA Environment Laboratories is to assist Member States in the use of both stable and radioisotope analytical techniques to understand, monitor and protect the environment. In this context, the major impact exerted by large coastal cities on marine ecosystems is an issue of primary concern for the IAEA and the IAEA Environment Laboratories. The marine pollution assessments required to understand such impacts depend on accurate knowledge of contaminant concentrations in various environmental compartments. The IAEA Environment Laboratories has been assisting national laboratories and regional laboratory networks since the early 1970s through the provision of reference material programme for the analysis of radionuclides, trace elements and organic compounds in marine samples. Quality assurance, quality control and associated good laboratory practice are essential components of all marine environmental monitoring studies. Quality control procedures are commonly based on the analysis of certified reference materials and reference samples in order to validate analytical methods used in monitoring studies and to assess the reliability and comparability of measurement data. Data that are not based on adequate quality assurance and quality control can be erroneous, and their misuse can lead to poor environmental management decisions. This publication describes the production of the IAEA-461 certified reference material, which was produced following ISO Guide 34:2009, General Requirements for the Competence of Reference Material Producers. A sample of approximately 60 kg of clams (Gafrarium tumidum) was collected in Noumea, New Caledonia, and processed at the IAEA Environment Laboratories to produce a certified reference material of marine biota. The sample contained certified mass fractions for arsenic, cadmium, calcium, chromium, cobalt, copper, iron, lead, mercury, methyl mercury, manganese, nickel, selenium, vanadium and zinc. The produced vials

  18. Ankle taping does not impair performance in jump or balance tests.

    Science.gov (United States)

    Abián-Vicén, Javier; Alegre, Luis M; Fernández-Rodríguez, J Manuel; Lara, Amador J; Meana, Marta; Aguado, Xavier

    2008-01-01

    This study aimed to investigate the influence of prophylactic ankle taping on two balance tests (static and dynamic balance) and one jump test, in the push off and the landing phase. Fifteen active young subjects (age: 21.0 ± 4.4 years) without previous ankle injuries volunteered for the study. Each participant performed three tests in two different situations: with taping and without taping. The tests were a counter movement jump, static balance, and a dynamic posturography test. The tests and conditions were randomly performed. The path of the center of pressures was measured in the balance tests, and the vertical ground reaction forces were recorded during the push-off and landing phases of the counter movement jump. Ankle taping had no influence on balance performance or in the push off phase of the jump. However, the second peak vertical force value during the landing phase of the jump was 12% greater with ankle taping (0.66 BW, 95% CI -0.64 to 1.96). The use of prophylactic ankle taping had no influence on the balance or jump performance of healthy young subjects. In contrast, the taped ankle increased the second peak vertical force value, which could be related to a greater risk of injury produced by the accumulation of repeated impacts in sports where jumps are frequently performed. Key pointsAnkle taping has no influence on balance performance.Ankle taping does not impair performance during the push-off phase of the jump.Ankle taping could increase the risk of injury during landings by increasing peak forces.

  19. VHS-tape system for general purpose computer. For next generation mass storage system

    International Nuclear Information System (INIS)

    Ukai, K.; Takano, M.; Shinohara, M.; Niki, K.; Suzuki, Y.; Hamada, T.; Ogawa, M.

    1994-07-01

    Mass storage is one of the key technology of next generation computer system. A huge amount of data is produced on a field of particle and nuclear physics. These data are raw data of experiments, analysis data, Monte Carlo simulations data, etc. We search a storage device for these data at the point of view of capacity, price, size, transfer speed, etc. We have selected a VHS-tape (12.7 mm-tape, helical scan) from many storage devices. Characteristics of the VHS-tape are as follows; capacity of 14.5 GB, size of 460 cm 3 , price of 1,000 yen (S-VHS tape for video use), and 1.996 MB/sec transfer speed at a sustained mode. Last year, we succeeded to operate the VHS-tape system on a workstation as a I/O device with read/write speed of 1.5 MB/sec. We have tested a VHS-tape system by connecting to the channel of the general purpose computer (Fujitsu M-780/10S) in our institute. We obtained a read and write speeds of 1.07 MB/sec and 1.72 MB/sec by FORTRAN test programs, respectively. Read speeds of an open reel tape and a 3480 type cassete tape by the same test programs are 1.13 MB/sec and 2.54 MB/sec, respectively. Speeds of write operation are 1.09 MB/sec and 2.54 MB/sec for the open reel and 3480 cassete tape, respectively. A start motion of the VHS-tape for read/write operations needs about 60 seconds. (author)

  20. A study of the naturalisation and dispersal of a non-native bivalve, the Manila clam, Ruditapes philippinarum (Adams and Reeve 1850) in estuaries along the South coast of England.

    OpenAIRE

    Harris, Matthew

    2016-01-01

    The Manila clam, Ruditapes philippinarum, was introduced into the British Isles in the 1980s for the purpose of aquaculture in order to take advantage of the rapid growth rate and high profitability of this non-native species. The decision to import the Manila clam, was based on the findings of a report commissioned by the Ministry of Agriculture Fisheries and Food which determined that the Manila clam would be able to be grown to marketable size faster than the local species Ruditapes decuss...

  1. Characterisation of 12 microsatellite loci in the Vietnamese commercial clam Lutraria rhynchaena Jonas 1844 (Heterodonta: Bivalvia: Mactridae) through next-generation sequencing.

    Science.gov (United States)

    Thai, Binh Thanh; Tan, Mun Hua; Lee, Yin Peng; Gan, Han Ming; Tran, Trang Thi; Austin, Christopher M

    2016-05-01

    The marine clam Lutraria rhynchaena is gaining popularity as an aquaculture species in Asia. Lutraria populations are present in the wild throughout Vietnam and several stocks have been established and translocated for breeding and aquaculture grow-out purposes. In this study, we demonstrate the feasibility of utilising Illumina next-generation sequencing technology to streamline the identification and genotyping of microsatellite loci from this clam species. Based on an initial partial genome scan, 48 microsatellite markers with similar melting temperatures were identified and characterised. The 12 most suitable polymorphic loci were then genotyped using 51 individuals from a population in Quang Ninh Province, North Vietnam. Genetic variation was low (mean number of alleles per locus = 2.6; mean expected heterozygosity = 0.41). Two loci showed significant deviation from Hardy-Weinberg equilibrium (HWE) and the presence of null alleles, but there was no evidence of linkage disequilibrium among loci. Three additional populations were screened (n = 7-36) to test the geographic utility of the 12 loci, which revealed 100 % successful genotyping in two populations from central Vietnam (Nha Trang). However, a second population from north Vietnam (Co To) could not be successfully genotyped and morphological evidence and mitochondrial variation suggests that this population represents a cryptic species of Lutraria. Comparisons of the Qang Ninh and Nha Trang populations, excluding the 2 loci out of HWE, revealed statistically significant allelic variation at 4 loci. We reported the first microsatellite loci set for the marine clam Lutraria rhynchaena and demonstrated its potential in differentiating clam populations. Additionally, a cryptic species population of Lutraria rhynchaena was identified during initial loci development, underscoring the overlooked diversity of marine clam species in Vietnam and the need to genetically characterise population representatives prior

  2. Distribution of haemic neoplasia of soft-shelled clams in Prince Edward Island: an examination of anthropogenic factors and effects of experimental fungicide exposure.

    Science.gov (United States)

    Mateo, D R; MacCallum, G S; McGladdery, S E; Davidson, J

    2016-05-01

    Haemic neoplasia was first considered a disease of concern for soft-shell clams in Prince Edward Island (PEI) when it was diagnosed as the cause of mass mortalities in 1999. The aetiology of the disease remains elusive, but has been associated with environmental degradation. In this study, a 2-year (2001-2002) geographic and seasonal survey was conducted for haemic neoplasia, using histology, in soft-shell clams from PEI. In addition, using geographic information system, the association between anthropogenic factors in the watersheds at sites affected by haemic neoplasia and the prevalence of the disease was investigated. Finally, histopathological changes were assessed in soft-shell clams experimentally exposed to four concentrations of chlorothalonil for 27 days. Haemic neoplasia could not be induced at any concentration of chlorothalonil. Clams exposed to a concentration of 1000 μg L(-1) of the fungicide, however, exhibited an LC50 of 17 days. Although this information provides additional toxicity information (LC50) for soft-shell clams, further experiments are required to assess longer term exposure to the fungicide. The highest prevalences of haemic neoplasia in PEI were found in North River and Miscouche (28.3-50.9% and 33.0-77.8%, respectively). No clear seasonal patterns were found. There was a correlation between haemic neoplasia prevalence and watersheds with a high percentage of potato acreage and forest coverage (P = 0.026 and P = 0.045, respectively), suggesting a link between anthropogenic activity and the prevalence of the disease. © 2015 John Wiley & Sons Ltd.

  3. LANDSAT-D data format control book. Volume 6, appendix G: GSFC HDT-AM inventory tape (GHIT-AM)

    Science.gov (United States)

    1981-01-01

    The data format specifications of the Goddard HDT inventory tapes (GHITS), which accompany shipments of archival digital multispectral scanner image data (HDT-AM tapes), are defined. The GHIT is a nine-track, 1600-BPI tape which conforms to the ANSI standard and serves as an inventory and description of the image data included in the shipment. The archival MSS tapes (HDT-AMs) contain radiometrically corrected but geometrically uncorrected image data plus certain ancillary data necessary to perform the geometric corrections.

  4. Recruitment of mud clam Polymesoda erosa (Solander, 1876 in a mangrove habitat of Chorao island, Goa

    Directory of Open Access Journals (Sweden)

    Sandhya Clemente

    2011-06-01

    Full Text Available Habitat-specific settlement success results either from active habitat selection or differential mortality after non-selective settlement. The mud clam Polymesoda erosa (Solander, 1876 is an ecologically and economically important benthic invertebrate with high abundance in the mangrove forests of Chorao Island, Goa, India. A one-year study (Jul 2004-Jul 2005 was conducted to characterize the patterns of post-larval settlement and survival of P. erosa in the mangrove habitat. The mean density of settling post-larvae was 28 no.m-2 with a majority of settlers during Sept 04. The density of adult clams in the landward zone ranged from 7-12 no.m-2 (mean: 9 ± 6 sd; n=122. In the seaward region, adults were completely absent at the low tide level. Higher densities of juveniles observed at the low- and mid-tide levels were assumed to be due to frequent inundation which allowed the young individuals to feed adequately and attain the critical sizes at which vulnerability to physical and biological constraints is substantially reduced, whereas, at high-tide level, increased desiccation may account for the mortality of settlers. It is speculated that initially the settlers settle according to the hydrodynamic conditions for sedimentation; however, adult survival is affected by their recruitment in a suitable habitat (e.g. substrates near Avicennia sp.. Thus, habitat dependent viability during the post-settlement phase could be the best explanation for the non-random, patchy distribution of P. erosa observed in the Chorao mangrove swamp.Um assentamento larval bem sucedido resulta da seleção ativa do habitat pelas larvas ou da mortalidade diferencial destas após o assentamento não seletivo. Nos manguezais da ilha Chorao, Goa, India, a ostra do lodo Polymesoda erosa (Solander, 1876 é um invertebrado muito abundante e de importância econômica. O presente trabalho, realizado durante um ano (julho de 2004 a julho de 2005, visou caracterizar os padr

  5. Pediatric Tape: Accuracy and Medication Delivery in the National Park Service

    Directory of Open Access Journals (Sweden)

    Danielle D. Campagne

    2015-10-01

    Full Text Available Introduction: The objective is to evaluate the accuracy of medication dosing and the time to medication administration in the prehospital setting using a novel length-based pediatric emergency resuscitation tape. Methods: This study was a two-period, two-treatment crossover trial using simulated pediatric patients in the prehospital setting. Each participant was presented with two emergent scenarios; participants were randomized to which case they encountered first, and to which case used the National Park Service (NPS emergency medical services (EMS length-based pediatric emergency resuscitation tape. In the control (without tape case, providers used standard methods to determine medication dosing (e.g. asking parents to estimate the patient’s weight; in the intervention (with tape case, they used the NPS EMS length-based pediatric emergency resuscitation tape. Each scenario required dosing two medications (Case 1 [febrile seizure] required midazolam and acetaminophen; Case 2 [anaphylactic reaction] required epinephrine and diphenhydramine. Twenty NPS EMS providers, trained at the Parkmedic/Advanced Emergency Medical Technician level, served as study participants. Results: The only medication errors that occurred were in the control (no tape group (without tape: 5 vs. with tape: 0, p=0.024. Time to determination of medication dose was significantly shorter in the intervention (with tape group than the control (without tape group, for three of the four medications used. In case 1, time to both midazolam and acetaminophen was significantly faster in the intervention (with tape group (midazolam: 8.3 vs. 28.9 seconds, p=0.005; acetaminophen: 28.6 seconds vs. 50.6 seconds, p=0.036. In case 2, time to epinephrine did not differ (23.3 seconds vs. 22.9 seconds, p=0.96, while time to diphenhydramine was significantly shorter in the intervention (with tape group (13 seconds vs. 37.5 seconds, p<0.05. Conclusion: Use of a length-based pediatric emergency

  6. Anisotropy of the critical current in MgB2 tapes made of high energy milled precursor powder

    DEFF Research Database (Denmark)

    Hässler, W.; Kovac, P.; Eisterer, M.

    2010-01-01

    For applications of MgB2 wires or tapes, high critical currents in high magnetic fields are essential. By using tapes in superconducting coils the anisotropic behaviour of the critical current, i.e. the dependence on the direction of the external field in relation to the tape surface, has to be t...

  7. Ceramic tape casting: A review of current methods and trends with emphasis on rheological behaviour and flow analysis

    DEFF Research Database (Denmark)

    Jabbaribehnam, Mirmasoud; Bulatova, Regina; Tok, A. I Y

    2016-01-01

    Tape casting has been used to produce thin layers of ceramics that can be used as single layers or can be stacked and laminated into multilayered structures. Today, tape casting is the basic fabrication process that provides multilayered capacitors and multilayered ceramic packages. In tape casti...

  8. Short-term acute hypercapnia affects cellular responses to trace metals in the hard clams Mercenaria mercenaria

    International Nuclear Information System (INIS)

    Ivanina, Anna V.; Beniash, Elia; Etzkorn, Markus; Meyers, Tiffany B.; Ringwood, Amy H.; Sokolova, Inna M.

    2013-01-01

    Highlights: •P CO 2 alters accumulation of Cd and Cu in clam cells. •Accumulation of Cd induces release of free Zn 2+ . •Accumulation of Cu induces an increase in free Cu 2+ and Fe 2+ . •Metal-induced oxidative stress is alleviated at high P CO 2 . •Toxicity of Cu in likely enhanced while that of Cd alleviated by high P CO 2 . -- Abstract: Estuarine and coastal habitats experience large fluctuations of environmental factors such as temperature, salinity, partial pressure of CO 2 (P CO 2 ) and pH; they also serve as the natural sinks for trace metals. Benthic filter-feeding organisms such as bivalves are exposed to the elevated concentrations of metals in estuarine water and sediments that can strongly affect their physiology. The effects of metals on estuarine organisms may be exacerbated by other environmental factors. Thus, a decrease in pH caused by high P CO 2 (hypercapnia) can modulate the effects of trace metals by affecting metal bioavailability, accumulation or binding. To better understand the cellular mechanisms of interactions between P CO 2 and trace metals in marine bivalves, we exposed isolated mantle cells of the hard clams (Mercenaria mercenaria) to different levels of P CO 2 (0.05, 1.52 and 3.01 kPa) and two major trace metal pollutants – cadmium (Cd) and copper (Cu). Elevated P CO 2 resulted in a decrease in intracellular pH (pH i ) of the isolated mantle cells from 7.8 to 7.4. Elevated P CO 2 significantly but differently affected the trace metal accumulation by the cells. Cd uptake was suppressed at elevated P CO 2 levels while Cu accumulation has greatly accelerated under hypercapnic conditions. Interestingly, at higher extracellular Cd levels, labile intracellular Cd 2+ concentration remained the same, while intracellular levels of free Zn 2+ increased suggesting that Cd 2+ substitutes bound Zn 2+ in these cells. In contrast, Cu exposure did not affect intracellular Zn 2+ but led to a profound increase in the intracellular levels

  9. Thermal Edge-Effects Model for Automated Tape Placement of Thermoplastic Composites

    Science.gov (United States)

    Costen, Robert C.

    2000-01-01

    Two-dimensional thermal models for automated tape placement (ATP) of thermoplastic composites neglect the diffusive heat transport that occurs between the newly placed tape and the cool substrate beside it. Such lateral transport can cool the tape edges prematurely and weaken the bond. The three-dimensional, steady state, thermal transport equation is solved by the Green's function method for a tape of finite width being placed on an infinitely wide substrate. The isotherm for the glass transition temperature on the weld interface is used to determine the distance inward from the tape edge that is prematurely cooled, called the cooling incursion Delta a. For the Langley ATP robot, Delta a = 0.4 mm for a unidirectional lay-up of PEEK/carbon fiber composite, and Delta a = 1.2 mm for an isotropic lay-up. A formula for Delta a is developed and applied to a wide range of operating conditions. A surprise finding is that Delta a need not decrease as the Peclet number Pe becomes very large, where Pe is the dimensionless ratio of inertial to diffusive heat transport. Conformable rollers that increase the consolidation length would also increase Delta a, unless other changes are made, such as proportionally increasing the material speed. To compensate for premature edge cooling, the thermal input could be extended past the tape edges by the amount Delta a. This method should help achieve uniform weld strength and crystallinity across the width of the tape.

  10. Influence of bress laminate volume fraction on electromechanical properties of externally laminated coated conductor tapes

    Energy Technology Data Exchange (ETDEWEB)

    Bautista, Zhierwinjay M.; Shin, Hyung Seop [Dept. of Mechanical Design Engineering, Andong National University, Andong (Korea, Republic of); Lee, Jae Hun; Lee, Hun Ju; Moon, Seung Hyun [SuNAM Co Ltd., Anseong (Korea, Republic of)

    2016-09-15

    The enhancement of mechanical properties of coated conductor (CC) tapes in practical application are usually achieved by reinforcing through lamination or electroplating metal layers on either sides of the CC tape. Mechanical or electromechanical properties of the CC tapes have been largely affected by the lamination structure under various loading modes such as tension, bending or even cyclic. In this study, the influence of brass laminate volume fraction on electromechanical properties of RCE-DR processed Gadolinium-barium-copper-oxide (GdBCO) CC tapes was investigated. The samples used were composed of single-side and both-side laminate of brass layer to the Cu-stabilized CC tape and their Ic behaviors were compared to those of the Cu-stabilized CC tape without external lamination. The stress/strain dependences of Ic in laminated CC tapes under uniaxial tension were analyzed and the irreversible stress/strain limits were determined. As a result, the increase of brass laminate volume fraction initially increased the irreversible strain limit and became gradual. The corresponding irreversible stress limit, however, showed no difference even though the brass laminate volume fraction increased to 3.4. But the irreversible load limit linearly increased with the brass laminate volume fraction.

  11. Kinesio® Tape Barrier Does Not Inhibit Intramuscular Cooling During Cryotherapy.

    Science.gov (United States)

    Lyman, Katie J; McCrone, Michael; Hanson, Thomas A; Mellinger, Christopher D; Gange, Kara

    2018-05-29

    Allied health care professionals commonly apply cryotherapy as treatment for acute musculoskeletal trauma and the associated symptoms. Understanding the impact of a tape barrier on intramuscular temperature can assist in determining treatment duration for effective cryotherapy. To determine whether Kinesio® Tape acts as a barrier that affects intramuscular temperature during cryotherapy application. A repeated-measures, counterbalanced design in which the independent variable was tape application and the dependent variable was muscle temperature as measured by thermocouples placed 1 cm beneath the adipose layer. Additional covariates for robustness were BMI and adipose thickness. University research laboratory. 19 male college students with no contraindications to cryotherapy, no known sensitivity to Kinesio® Tape, and no reported quadriceps injury within the past six months. Topical cryotherapy: crushed-ice bags of 1 kg and 0.5 kg. Intramuscular temperature. The tape barrier had no statistically significant effect on muscle temperature. The pattern of temperature change was indistinguishable between participants with and without tape application. Findings suggest health care professionals can combine cryotherapy with a Kinesio® Tape application without any need for adjustments to cryotherapy duration.

  12. Fabrication and properties of Ag-Bi2223 tapes with resistive barriers for filament decoupling

    International Nuclear Information System (INIS)

    Inada, Ryoji; Fukumoto, Yohei; Yasunami, Taeko; Nakamura, Yuichi; Oota, Akio; Li Chengshang; Zhang Pingxiang

    2007-01-01

    In this paper, we prepared the Bi2223 multifilamentary tapes with Ca 2 CuO 3 + Bi2212 as interfilamentary resistive barriers to suppress the electromagnetic coupling among the filaments under AC external magnetic field. The tapes with thin barrier layers of Ca 2 CuO 3 + 30 wt% Bi2212 around the filaments were prepared by using a standard powder-in-tube (PIT) method. The outside surface of monocore Ag-sheathed rods was coated by barrier materials. Then, the several coated monocore wires were stacked and packed into another Ag or Ag-Mg alloy tube. The packed tube was drawn and rolled into tape shape. The tape was subsequently sintered to form Bi2223 phase inside filaments. For the characterization of tapes, X-ray diffraction measurements were performed to investigate the phase formation inside the filaments. The uniformity of transport properties (J c ) for barrier tapes were evaluated on the order of several metre lengths and compared with the result for the tapes without barriers. Finally, AC loss characteristics under AC parallel transverse magnetic field were investigated to examine the effect of introducing the barriers on the filament decoupling

  13. Research and development efforts relative to superconducting materials. Final report. [Nb/sub 3/Sn tapes

    Energy Technology Data Exchange (ETDEWEB)

    Adam, E; Beishcher, P; Marancik, W; Lucariello, R; Young, M

    1976-04-01

    Three processes for the production of low-loss superconducting tapes of Nb/sub 3/Sn were investigated. They are the rolled-bronze process, the electron beam (EB) bronze deposition process, and the high-rate sputtering process. Shortly after the start of the investigation, effort on the last two processes was suspended because the process-development time that would be needed to arrive at a suitable transmission-line tape appeared most likely to be the shortest with the rolled-bronze process. Long lengths of Nb/sub 3/Sn tapes were prepared by the rolled-bronze process from extruded and rolled bronze-clad niobium billets. Tapes were stabilized by removing the bronze layer after reaction and then coating the exposed Nb/sub 3/Sn with high-purity copper by EB evaporation. Several meters of high quality Nb/sub 3/Sn tapes were produced by the rolled-bronze process. Even when the tapes were stabilized with copper, the losses were as low as 1.8 ..mu..W/cm/sup 2/ at 4.2 K and a surface current density of 500 rms A/cm. Despite early curtailment of the effort on the EB bronze-deposition process, short samples of Nb/sub 3/Sn tapes were produced.

  14. ANKLE TAPING DOES NOT IMPAIR PERFORMANCE IN JUMP OR BALANCE TESTS

    Directory of Open Access Journals (Sweden)

    Javier Abián-Vicén

    2008-09-01

    Full Text Available This study aimed to investigate the influence of prophylactic ankle taping on two balance tests (static and dynamic balance and one jump test, in the push off and the landing phase. Fifteen active young subjects (age: 21.0 ± 4.4 years without previous ankle injuries volunteered for the study. Each participant performed three tests in two different situations: with taping and without taping. The tests were a counter movement jump, static balance, and a dynamic posturography test. The tests and conditions were randomly performed. The path of the center of pressures was measured in the balance tests, and the vertical ground reaction forces were recorded during the push-off and landing phases of the counter movement jump. Ankle taping had no influence on balance performance or in the push off phase of the jump. However, the second peak vertical force value during the landing phase of the jump was 12% greater with ankle taping (0.66 BW, 95% CI -0.64 to 1.96. The use of prophylactic ankle taping had no influence on the balance or jump performance of healthy young subjects. In contrast, the taped ankle increased the second peak vertical force value, which could be related to a greater risk of injury produced by the accumulation of repeated impacts in sports where jumps are frequently performed

  15. Identification and quantification of glue-like off-odors in elastic therapeutic tapes.

    Science.gov (United States)

    Denk, Philipp; Buettner, Andrea

    2018-05-01

    Elastic therapeutic tapes are an important tool in the field of physical therapy and medicine. These tapes contain types of adhesive. However, sensory evaluations revealed the release of pronounced and irritating odors of the tapes. Negative odors were, amongst others, reported in elastic therapeutic tapes containing acrylic adhesives. In this study, the odor of four different tape samples was evaluated applying a descriptive analysis approach carried out by a trained sensory panel. Afterwards, the volatile compounds were recovered from the samples by solvent extraction and isolated by solvent-assisted flavor evaporation (SAFE). The obtained distillates were subsequently analyzed by gas chromatography-olfactometry (GC-O) and two-dimensional GC-O coupled with mass spectrometry (2D-GC-MS/O). To determine the most potent odorants in the distillates, odor extract dilution analyses (OEDA) were carried out. Thirty-one odorants were successfully identified using this approach, which were all described for the first time as odorants in tapes. Amongst the set of volatiles, unsaturated and saturated aldehydes were present, eliciting fatty, soapy, and citrus-like odor impressions, as well as a range of glue-like, moldy, and fruity smelling odor-active volatiles, such as 2-ethyl-1-hexanol, butyl benzoate, and 3-phenyltoluene. Based on their relative intensities, the concentrations of the glue-like smelling substances were determined: 2-ethyl-1-hexanol, present in all samples, was determined with concentrations ranging from 10 to 200 mg/kg in the investigated tapes.

  16. Degradation characteristics of 2G HTS tapes with respect to an electrical breakdown

    International Nuclear Information System (INIS)

    Kang, Jong O; Lee, On You; Mo, Young Kyu; Kim, Jun Il; Bang, Seung Min; Lee, Hong Seok; Kang, Hyoung Ku; Lee, Jae Hun; Jang, Cheol Yeong

    2015-01-01

    The electrical insulation design for a superconducting coil system is important for developing high voltage superconducting apparatuses. Also, the degraded characteristics of superconducting tapes due to an electrical breakdown should be considered for superconducting coils design. In this study, the degradation characteristics of 2G high temperature superconducting (HTS) tapes were studied with respect to electrical breakdown tests. The degradation tests of 2G HTS tapes were performed with various stabilizer materials. The degradation characteristics of 2G HTS tapes such as critical current(Ic) and index number were observed by performing electrical breakdown tests. It was found that the characteristics such as Ic and index number can be degraded by an electrical breakdown. Moreover, it was concluded that the degradation characteristics of 2G HTS tapes were affected by a stabilizer material and applied breakdown voltage. The cross sectional view of 2G HTS tapes was observed by using a scanning electron microscope (SEM). As results, it is found that the degradation characteristics of 2G HTS tapes are concerned with hardness and electrical resistivity of stabilizer layers

  17. Does taping in addition to physiotherapy improve the outcomes in subacromial impingement syndrome? A systematic review.

    Science.gov (United States)

    Saracoglu, Ismail; Emuk, Yusuf; Taspinar, Ferruh

    2018-04-01

    Taping is used with or without other interventions for many purposes, especially to manage pain and improve functional activity in patients with shoulder pain. The aim of this review was to determine whether any taping technique in addition to physiotherapy care is more effective than physiotherapy care alone in patients with shoulder impingement syndrome. A systematic search of Cochrane Database of Systematic Review, MEDLINE (EBSCO), Physiotherapy Evidence Database (PEDro), CINAHL (EBSCO), PUBMED, AMED, EMBASE (OVID), The Kinesio Kinesio® Taping Method, Kinesio® Tex Tape UK and International websites ( www.kinesiotaping.co.uk ; www.kinesiotaping.com ) was conducted to June 2015. The outcome measures were pain, disability, range of motion and muscle strength. As data were not suitable for meta-analysis, narrative synthesis were applied. Three randomized controlled trials and one controlled trial (135 patients) were included. The results were conflicting and weak on the effectiveness of taping as an adjunct therapy for improvement of pain, disability, range of motion and muscle strength. Clinical taping in addition to physiotherapy interventions (e.g. exercise, electrotherapy, and manual therapy) might be an optional modality for managing patients with shoulder impingement syndrome, especially for the initial stage of the treatment; however, we need further robust, placebo controlled and consistent studies to prove whether it is more effective than physiotherapy interventions without taping.

  18. Ankle taping can reduce external ankle joint moments during drop landings on a tilted surface.

    Science.gov (United States)

    Sato, Nahoko; Nunome, Hiroyuki; Hopper, Luke S; Ikegami, Yasuo

    2017-09-20

    Ankle taping is commonly used to prevent ankle sprains. However, kinematic assessments investigating the biomechanical effects of ankle taping have provided inconclusive results. This study aimed to determine the effect of ankle taping on the external ankle joint moments during a drop landing on a tilted surface at 25°. Twenty-five participants performed landings on a tilted force platform that caused ankle inversion with and without ankle taping. Landing kinematics were captured using a motion capture system. External ankle inversion moment, the angular impulse due to the medio-lateral and vertical components of ground reaction force (GRF) and their moment arm lengths about the ankle joint were analysed. The foot plantar inclination relative to the ground was assessed. In the taping condition, the foot plantar inclination and ankle inversion angular impulse were reduced significantly compared to that of the control. The only component of the external inversion moment to change significantly in the taped condition was a shortened medio-lateral GRF moment arm length. It can be assumed that the ankle taping altered the foot plantar inclination relative to the ground, thereby shortening the moment arm of medio-lateral GRF that resulted in the reduced ankle inversion angular impulse.

  19. Kinesio Taping to generate skin convolutions is not better than sham taping for people with chronic non-specific low back pain: a randomised trial

    Directory of Open Access Journals (Sweden)

    Patrícia do Carmo Silva Parreira

    2014-06-01

    Full Text Available Question: For people with chronic low back pain, does Kinesio Taping, applied according to the treatment manual to create skin convolutions, reduce pain and disability more than a simple application without convolutions? Design: Randomised trial with concealed allocation, intention-to-treat analysis and blinded assessment of some outcomes. Participants: 148 participants with chronic non-specific low back pain. Intervention: Experimental group participants received eight sessions (over four weeks of Kinesio Taping applied according to the Kinesio Taping Method treatment manual (ie, 10 to 15% tension applied in flexion to create skin convolutions in neutral. Control group participants received eight sessions (over four weeks of Kinesio Taping with no tension, creating no convolutions. Outcome measures: The primary outcome measures were pain intensity and disability after the four-week intervention. Secondary outcomes were pain intensity and disability 12 weeks after randomisation, and global perceived effect at both four and 12 weeks after randomisation. Results: Applying Kinesio Tape to create convolutions in the skin did not significantly change its effect on pain (MD–0.4 points, 95% CI–1.3 to 0.4 or disability (MD–0.3 points, 95% CI–1.9 to 1.3 at four weeks. There was a small difference in favour of the experimental group for the secondary outcome of global perceived effect (MD 1.4 points, 95% CI 0.3 to 2.5 at four weeks. No significant between-group differences were observed for the other secondary outcomes. Conclusion: Kinesio Taping applied with stretch to generate convolutions in the skin was no more effective than simple application of the tape without tension for the outcomes measured. These results challenge the proposed mechanism of action of this therapy. Trial registration: Brazilian Registry of Clinical Trials, RBR-7ggfkv. [Parreira PCS, Costa LCM, Takahashi R, Hespanhol Junior LC, da Luz Junior MA, da Silva TM, Costa LOP

  20. Tack Measurements of Prepreg Tape at Variable Temperature and Humidity

    Science.gov (United States)

    Wohl, Christopher; Palmieri, Frank L.; Forghani, Alireza; Hickmott, Curtis; Bedayat, Houman; Coxon, Brian; Poursartip, Anoush; Grimsley, Brian

    2017-01-01

    NASA’s Advanced Composites Project has established the goal of achieving a 30 percent reduction in the timeline for certification of primary composite structures for application on commercial aircraft. Prepreg tack is one of several critical parameters affecting composite manufacturing by automated fiber placement (AFP). Tack plays a central role in the prevention of wrinkles and puckers that can occur during AFP, thus knowledge of tack variation arising from a myriad of manufacturing and environmental conditions is imperative for the prediction of defects during AFP. A full design of experiments was performed to experimentally characterize tack on 0.25-inch slit-tape tow IM7/8552-1 prepreg using probe tack testing. Several process parameters (contact force, contact time, retraction speed, and probe diameter) as well as environmental parameters (temperature and humidity) were varied such that the entire parameter space could be efficiently evaluated. Mid-point experimental conditions (i.e., parameters not at either extrema) were included to enable prediction of curvature in relationships and repeat measurements were performed to characterize experimental error. Collectively, these experiments enable determination of primary dependencies as well as multi-parameter relationships. Slit-tape tow samples were mounted to the bottom plate of a rheometer parallel plate fixture using a jig to prevent modification of the active area to be interrogated with the top plate, a polished stainless steel probe, during tack testing. The probe surface was slowly brought into contact with the pre-preg surface until a pre-determined normal force was achieved (2-30 newtons). After a specified dwell time (0.02-10 seconds), during which the probe substrate interaction was maintained under displacement control, the probe was retracted from the surface (0.1-50 millimeters per second). Initial results indicated a clear dependence of tack strength on several parameters, with a particularly