WorldWideScience

Sample records for circuit analyzers

  1. Analyzing a Vibrating Wire Transducer using Coupled Resonator Circuits

    Directory of Open Access Journals (Sweden)

    POP, S.

    2015-08-01

    Full Text Available This paper intends to be an approach on the vibrating wire transducer from the perspective of the necessary rules used for a correct measurement procedure. There are several studies which analyze the vibrating wire transducer as a mechanical system. However, a comparative time-domain analysis between the mechanical and the electrical model is lacking. The transducer analysis is based on a theoretical analysis of the equivalent circuit, on both excitation and response time intervals. The electrical model consists of two magnetic coupled resonating circuits. When connected to an excitation source, there will be an energy transfer from the coil to the wire. The maximum energy transfer will occur at the vibrating wire's frequency of resonance. Using the transient regime analysis, it has been proven that, in the response time interval - when the wire vibrates freely, the current through the circuit that models the wire describes the oscillating movement of the wire. A complex signal is obtained, that contains both coil's and wire's frequencies of resonance, strongly dependent with theirs parasitic elements. The mathematical analysis highlights the similarity between mechanical and electrical model and the procedures in order to determine the wire frequency of resonance from the output signal.

  2. Graphene-based THz modulator analyzed by equivalent circuit model

    DEFF Research Database (Denmark)

    Xiao, Binggang; Chen, Jing; Xie, Zhiyi;

    2016-01-01

    A terahertz (THz) modulator based on graphene is proposed and analysed by use of equivalent transmission line of a homogeneous mediumand the local anisotropic model of the graphene conductivity. The result calculated by the equivalent circuit is consistent with that obtained byFresnel transfer ma...

  3. Application of Printed Circuit Board Technology to FT-ICR MS Analyzer Cell Construction and Prototyping

    Science.gov (United States)

    Leach, Franklin E.; Norheim, Randolph; Anderson, Gordon; Pasa-Tolic, Ljiljana

    2014-12-01

    Although Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS) remains the mass spectrometry platform that provides the highest levels of performance for mass accuracy and resolving power, there is room for improvement in analyzer cell design as the ideal quadrupolar trapping potential has yet to be generated for a broadband MS experiment. To this end, analyzer cell designs have improved since the field's inception, yet few research groups participate in this area because of the high cost of instrumentation efforts. As a step towards reducing this barrier to participation and allowing for more designs to be physically tested, we introduce a method of FT-ICR analyzer cell prototyping utilizing printed circuit boards at modest vacuum conditions. This method allows for inexpensive devices to be readily fabricated and tested over short intervals and should open the field to laboratories lacking or unable to access high performance machine shop facilities because of the required financial investment.

  4. D-VASim: Dynamic Virtual Analyzer and Simulator for Genetic Circuits

    DEFF Research Database (Denmark)

    Baig, Hasan; Madsen, Jan

    2015-01-01

    , with the aim to reduce the number of required in-vitro experiments. We present a behavioural simulation and analysis tool that allows the biologist to carry out virtual lab experiments as an interactive process during simulation of the genetic circuit, rather than a batch process, which is current practice. We......A genetic circuit represents a gene regulator network that is triggered by a combination of external signals, such as chemicals, proteins, light or temperature, to emit signals to control gene expression or metabolic pathways accordingly. In order to match the intended behaviour, genetic circuits...... are either assembled from a standard library of well-defined genetic gates or from parts of an available library, for instance, BioBricks. The obtained behavior can be validated through in-silico analysis, solving reaction kinetics using ordinary differential equations (ODEs) or by stochastic simulation...

  5. Analyzing the effects of post couplers in DTL tuning by the equivalent circuit model

    CERN Document Server

    Jia, Xiaoyu

    2013-01-01

    Stabilization of the accelerating field in Drift Tube Linac(DTL) is obtained by inserting Post Couplers(PCs).On the basis of the circuit model equivalent for the DTL with and without asymmetrical PCs, stabilization is deduced quantitatively: let $\\delta \\omega/\\omega_0$ be the relative frequency error, then we discover that the sensitivity of field to perturbation is proportional to $\\sqrt{\\delta \\omega / \\omega_0}$ without PCs and to $\\delta \\omega/\\omega_0$ with PCs. Then we adapt the circuit model of symmetrical PCs for the case of asymmetrical PCs. The circuit model shows how the slope of field distribution is changed by rotating the asymmetrical PCs and illustrates that the asymmetrical PCs have the same effect as the symmetrical ones in stabilization.

  6. Analyzing the effects of post couplers in DTL tuning by the equivalent circuit model

    Science.gov (United States)

    Jia, Xiao-Yu; Zheng, Shu-Xin

    2013-12-01

    Stabilization of the accelerating field in Drift Tube Linac(DTL) is obtained by inserting Post Couplers(PCs). On the basis of the equivalent circuit model for the DTL with and without asymmetrical PCs, stabilization is deduced quantitatively: we let δω/ω0 be the relative frequency error, then we discover that the sensitivity of field to perturbation is proportional to without PCs and to δω/ω0 with PCs. Then we adapt the circuit model of symmetrical PCs for the case of asymmetrical PCs. The circuit model shows how the slope of field distribution is changed by rotating the asymmetrical PCs and illustrates that the asymmetrical PCs have the same effect as the symmetrical ones in stabilization.

  7. Analyzing the effects of post couplers in DTL tuning by the equivalent circuit model

    OpenAIRE

    Jia, Xiaoyu; Zheng, Shuxin

    2013-01-01

    Stabilization of the accelerating field in Drift Tube Linac(DTL) is obtained by inserting Post Couplers(PCs).On the basis of the circuit model equivalent for the DTL with and without asymmetrical PCs, stabilization is deduced quantitatively: let $\\delta \\omega/\\omega_0$ be the relative frequency error, then we discover that the sensitivity of field to perturbation is proportional to $\\sqrt{\\delta \\omega / \\omega_0}$ without PCs and to $\\delta \\omega/\\omega_0$ with PCs. Then we adapt the circu...

  8. Intuitive analog circuit design

    CERN Document Server

    Thompson, Marc

    2013-01-01

    Intuitive Analog Circuit Design outlines ways of thinking about analog circuits and systems that let you develop a feel for what a good, working analog circuit design should be. This book reflects author Marc Thompson's 30 years of experience designing analog and power electronics circuits and teaching graduate-level analog circuit design, and is the ideal reference for anyone who needs a straightforward introduction to the subject. In this book, Dr. Thompson describes intuitive and ""back-of-the-envelope"" techniques for designing and analyzing analog circuits, including transistor amplifi

  9. Positive fractional linear electrical circuits

    Science.gov (United States)

    Kaczorek, Tadeusz

    2013-10-01

    The positive fractional linear systems and electrical circuits are addressed. New classes of fractional asymptotically stable and unstable electrical circuits are introduced. The Caputo and Riemann-Liouville definitions of fractional derivatives are used to analysis of the positive electrical circuits composed of resistors, capacitors, coils and voltage (current) sources. The positive fractional electrical and specially unstable different types electrical circuits are analyzed. Some open problems are formulated.

  10. Experimental determination of circuit equations

    CERN Document Server

    Shulman, Jason; Widjaja, Matthew; Gunaratne, Gemunu H

    2013-01-01

    Kirchhoff's laws offer a general, straightforward approach to circuit analysis. Unfortunately, use of the laws becomes impractical for all but the simplest of circuits. This work presents a novel method of analyzing direct current resistor circuits. It is based on an approach developed to model complex networks, making it appropriate for use on large, complicated circuits. It is unique in that it is not an analytic method. It is based on experiment, yet the approach produces the same circuit equations obtained by more traditional means.

  11. Circuit Training.

    Science.gov (United States)

    Nelson, Jane B.

    1998-01-01

    Describes a research-based activity for high school physics students in which they build an LC circuit and find its resonant frequency of oscillation using an oscilloscope. Includes a diagram of the apparatus and an explanation of the procedures. (DDR)

  12. Controllable circuit

    DEFF Research Database (Denmark)

    2010-01-01

    A switch-mode power circuit comprises a controllable element and a control unit. The controllable element is configured to control a current in response to a control signal supplied to the controllable element. The control unit is connected to the controllable element and provides the control...

  13. CADAT integrated circuit mask analysis

    Science.gov (United States)

    1981-01-01

    CADAT System Mask Analysis Program (MAPS2) is automated software tool for analyzing integrated-circuit mask design. Included in MAPS2 functions are artwork verification, device identification, nodal analysis, capacitance calculation, and logic equation generation.

  14. Design of analog circuits through symbolic analysis

    CERN Document Server

    Fakhfakh, Mourad; V Fernández, Francisco

    2012-01-01

    Symbolic analyzers have the potential to offer knowledge to sophomores as well as practitioners of analog circuit design. Actually, they are an essential complement to numerical simulators, since they provide insight into circuit behavior which numerical analyzers do not provide. Symbolic analysis of electronic circuits addresses the generation of symbolic expressions for the parameters that describe the performance of linear and nonlinear circuits in three domains: DC, AC and time; some or all the circuit parameters can be kept as symbols. Due to the fact that these expressions remain va

  15. EDA circuit simulation

    International Nuclear Information System (INIS)

    EDA technique is used for circuit simulation. The circuit simulation and the analysis are made for a gate circuit one-shot multivibrator. The result shows: EDA circuit simulation is very useful technique

  16. Analog and VLSI circuits

    CERN Document Server

    Chen, Wai-Kai

    2009-01-01

    Featuring hundreds of illustrations and references, this book provides the information on analog and VLSI circuits. It focuses on analog integrated circuits, presenting the knowledge on monolithic device models, analog circuit cells, high performance analog circuits, RF communication circuits, and PLL circuits.

  17. Short- circuit tests of circuit breakers

    OpenAIRE

    Chorovský, P.

    2015-01-01

    This paper deals with short-circuit tests of low voltage electrical devices. In the first part of this paper, there are described basic types of short- circuit tests and their principles. Direct and indirect (synthetic) tests with more details are described in the second part. Each test and principles are explained separately. Oscilogram is obtained from short-circuit tests of circuit breakers at laboratory. The aim of this research work is to propose a test circuit for performing indirect test.

  18. Fractional linear systems and electrical circuits

    CERN Document Server

    Kaczorek, Tadeusz

    2015-01-01

    This monograph covers some selected problems of positive and fractional electrical circuits composed of resistors, coils, capacitors and voltage (current) sources. The book consists of 8 chapters, 4 appendices and a list of references. Chapter 1 is devoted to fractional standard and positive continuous-time and discrete-time linear systems without and with delays. In chapter 2 the standard and positive fractional electrical circuits are considered and the fractional electrical circuits in transient states are analyzed.  Descriptor linear electrical circuits and their properties are investigated in chapter 3,  while chapter 4 is devoted to the stability of fractional standard and positive linear electrical circuits. The reachability, observability and reconstructability of fractional positive electrical circuits and their decoupling zeros are analyzed in chapter 5. The fractional linear electrical circuits with feedbacks are considered in chapter 6. In chapter 7 solutions of minimum energy control for standa...

  19. Collective of mechatronics circuit

    International Nuclear Information System (INIS)

    This book is composed of three parts, which deals with mechatronics system about sensor, circuit and motor. The contents of the first part are photo sensor of collector for output, locating detection circuit with photo interrupts, photo sensor circuit with CdS cell and lamp, interface circuit with logic and LED and temperature sensor circuit. The second part deals with oscillation circuit with crystal, C-R oscillation circuit, F-V converter, timer circuit, stability power circuit, DC amp and DC-DC converter. The last part is comprised of bridge server circuit, deformation bridge server, controlling circuit of DC motor, controlling circuit with IC for PLL and driver circuit of stepping motor and driver circuit of Brushless.

  20. Oxygen analyzer

    Science.gov (United States)

    Benner, William H.

    1986-01-01

    An oxygen analyzer which identifies and classifies microgram quantities of oxygen in ambient particulate matter and for quantitating organic oxygen in solvent extracts of ambient particulate matter. A sample is pyrolyzed in oxygen-free nitrogen gas (N.sub.2), and the resulting oxygen quantitatively converted to carbon monoxide (CO) by contact with hot granular carbon (C). Two analysis modes are made possible: (1) rapid determination of total pyrolyzable oxygen obtained by decomposing the sample at 1135.degree. C., or (2) temperature-programmed oxygen thermal analysis obtained by heating the sample from room temperature to 1135.degree. C. as a function of time. The analyzer basically comprises a pyrolysis tube containing a bed of granular carbon under N.sub.2, ovens used to heat the carbon and/or decompose the sample, and a non-dispersive infrared CO detector coupled to a mini-computer to quantitate oxygen in the decomposition products and control oven heating.

  1. Analog circuit design designing dynamic circuit response

    CERN Document Server

    Feucht, Dennis

    2010-01-01

    This second volume, Designing Dynamic Circuit Response builds upon the first volume Designing Amplifier Circuits by extending coverage to include reactances and their time- and frequency-related behavioral consequences.

  2. Photomultiplier blanking circuit

    Science.gov (United States)

    Mcclenahan, J. O.

    1972-01-01

    Circuit for protecting photomultiplier equipment from current surges which occur when exposed to brilliant illumination is discussed. Components of circuit and details of operation are provided. Circuit diagram to show action of blanking pulse on zener diode is included.

  3. Analog circuit design designing waveform processing circuits

    CERN Document Server

    Feucht, Dennis

    2010-01-01

    The fourth volume in the set Designing Waveform-Processing Circuits builds on the previous 3 volumes and presents a variety of analog non-amplifier circuits, including voltage references, current sources, filters, hysteresis switches and oscilloscope trigger and sweep circuitry, function generation, absolute-value circuits, and peak detectors.

  4. Worst Asymmetrical Short-Circuit Current

    DEFF Research Database (Denmark)

    Arana Aristi, Iván; Holmstrøm, O; Grastrup, L;

    2010-01-01

    In a typical power plant, the production scenario and the short-circuit time were found for the worst asymmetrical short-circuit current. Then, a sensitivity analysis on the missing generator values was realized in order to minimize the uncertainty of the results. Afterward the worst asymmetrical...... short-circuit current was analyzed in order to compare the results with the allowable DC current component based in the IEC. Finally the normal operating condition for the power plant was modeled....

  5. Nonsmooth Modeling and Simulation for Switched Circuits

    CERN Document Server

    Acary, Vincent; Brogliato, Bernard

    2011-01-01

    "Nonsmooth Modeling and Simulation for Switched Circuits" concerns the modeling and the numerical simulation of switched circuits with the nonsmooth dynamical systems (NSDS) approach, using piecewise-linear and multivalued models of electronic devices like diodes, transistors, switches. Numerous examples (ranging from introductory academic circuits to various types of power converters) are analyzed and many simulation results obtained with the INRIA open-source SICONOS software package are presented. Comparisons with SPICE and hybrid methods demonstrate the power of the NSDS approach

  6. The analysis and design of linear circuits

    CERN Document Server

    Thomas, Roland E; Toussaint, Gregory J

    2009-01-01

    The Analysis and Design of Linear Circuits, 6e gives the reader the opportunity to not only analyze, but also design and evaluate linear circuits as early as possible. The text's abundance of problems, applications, pedagogical tools, and realistic examples helps engineers develop the skills needed to solve problems, design practical alternatives, and choose the best design from several competing solutions. Engineers searching for an accessible introduction to resistance circuits will benefit from this book that emphasizes the early development of engineering judgment.

  7. Solid-state circuits

    CERN Document Server

    Pridham, G J

    2013-01-01

    Solid-State Circuits provides an introduction to the theory and practice underlying solid-state circuits, laying particular emphasis on field effect transistors and integrated circuits. Topics range from construction and characteristics of semiconductor devices to rectification and power supplies, low-frequency amplifiers, sine- and square-wave oscillators, and high-frequency effects and circuits. Black-box equivalent circuits of bipolar transistors, physical equivalent circuits of bipolar transistors, and equivalent circuits of field effect transistors are also covered. This volume is divided

  8. Circuit analysis for dummies

    CERN Document Server

    Santiago, John

    2013-01-01

    Circuits overloaded from electric circuit analysis? Many universities require that students pursuing a degree in electrical or computer engineering take an Electric Circuit Analysis course to determine who will ""make the cut"" and continue in the degree program. Circuit Analysis For Dummies will help these students to better understand electric circuit analysis by presenting the information in an effective and straightforward manner. Circuit Analysis For Dummies gives you clear-cut information about the topics covered in an electric circuit analysis courses to help

  9. Electronic devices and circuits

    CERN Document Server

    Pridham, Gordon John

    1972-01-01

    Electronic Devices and Circuits, Volume 3 provides a comprehensive account on electronic devices and circuits and includes introductory network theory and physics. The physics of semiconductor devices is described, along with field effect transistors, small-signal equivalent circuits of bipolar transistors, and integrated circuits. Linear and non-linear circuits as well as logic circuits are also considered. This volume is comprised of 12 chapters and begins with an analysis of the use of Laplace transforms for analysis of filter networks, followed by a discussion on the physical properties of

  10. The circuit designer's companion

    CERN Document Server

    Williams, Tim

    2013-01-01

    The Circuit Designer's Companion covers the theoretical aspects and practices in analogue and digital circuit design. Electronic circuit design involves designing a circuit that will fulfill its specified function and designing the same circuit so that every production model of it will fulfill its specified function, and no other undesired and unspecified function.This book is composed of nine chapters and starts with a review of the concept of grounding, wiring, and printed circuits. The subsequent chapters deal with the passive and active components of circuitry design. These topics are foll

  11. Electrical Circuits and Water Analogies

    Science.gov (United States)

    Smith, Frederick A.; Wilson, Jerry D.

    1974-01-01

    Briefly describes water analogies for electrical circuits and presents plans for the construction of apparatus to demonstrate these analogies. Demonstrations include series circuits, parallel circuits, and capacitors. (GS)

  12. Equivalent Circuits For AC-Impedance Analysis Of Corrosion

    Science.gov (United States)

    Danford, M. D.

    1992-01-01

    Report presents investigation of equivalent circuits for ac-impedance analysis of corrosion. Impedance between specimen and electrolyte measured as function of frequency. Data used to characterize corrosion electrochemical system in terms of equivalent circuit. Eleven resistor/capacitor equivalent-circuit models were analyzed.

  13. Circuit mismatch influence on performance of paralleling silicon carbide MOSFETs

    DEFF Research Database (Denmark)

    Li, Helong; Munk-Nielsen, Stig; Pham, Cam;

    2014-01-01

    This paper focuses on circuit mismatch influence on performance of paralleling SiC MOSFETs. Power circuit mismatch and gate driver mismatch influences are analyzed in detail. Simulation and experiment results show the influence of circuit mismatch and verify the analysis. This paper aims to give...

  14. Designing of Acousto-optic Spectrum Analyzer

    Institute of Scientific and Technical Information of China (English)

    WANG Dan-zhi; SHAO Ding-rong; LI Shu-jian

    2004-01-01

    The structure of the acousto-optic spectrum analyzer was investigated including the RF amplifying circuit, the optical structures and the postprocessing circuit, and the design idea of the module was applied to design the spectrum analyzer. The modularization spectrum analyzer takes on the performance stabilization and higher reliability, and according to different demands, the different modules can be used. The spectrum analyzer had such performances as the detecting frequency error of 0.58MHz,detecting responsivity of 90 dBm and bandwidth of 50 Mhz.

  15. Circuits on Cylinders

    DEFF Research Database (Denmark)

    Hansen, Kristoffer Arnsfelt; Miltersen, Peter Bro; Vinay, V

    2006-01-01

    We consider the computational power of constant width polynomial size cylindrical circuits and nondeterministic branching programs. We show that every function computed by a Pi2 o MOD o AC0 circuit can also be computed by a constant width polynomial size cylindrical nondeterministic branching...... program (or cylindrical circuit) and that every function computed by a constant width polynomial size cylindrical circuit belongs to ACC0....

  16. Electric circuits essentials

    CERN Document Server

    REA, Editors of

    2012-01-01

    REA's Essentials provide quick and easy access to critical information in a variety of different fields, ranging from the most basic to the most advanced. As its name implies, these concise, comprehensive study guides summarize the essentials of the field covered. Essentials are helpful when preparing for exams, doing homework and will remain a lasting reference source for students, teachers, and professionals. Electric Circuits I includes units, notation, resistive circuits, experimental laws, transient circuits, network theorems, techniques of circuit analysis, sinusoidal analysis, polyph

  17. Signal sampling circuit

    NARCIS (Netherlands)

    Louwsma, Simon Minze; Vertregt, Maarten

    2010-01-01

    A sampling circuit for sampling a signal is disclosed. The sampling circuit comprises a plurality of sampling channels adapted to sample the signal in time-multiplexed fashion, each sampling channel comprising a respective track-and-hold circuit connected to a respective analogue to digital converte

  18. Signal sampling circuit

    NARCIS (Netherlands)

    Louwsma, Simon Minze; Vertregt, Maarten

    2011-01-01

    A sampling circuit for sampling a signal is disclosed. The sampling circuit comprises a plurality of sampling channels adapted to sample the signal in time-multiplexed fashion, each sampling channel comprising a respective track-and-hold circuit connected to a respective analogue to digital converte

  19. Piezoelectric drive circuit

    Science.gov (United States)

    Treu, Jr., Charles A.

    1999-08-31

    A piezoelectric motor drive circuit is provided which utilizes the piezoelectric elements as oscillators and a Meacham half-bridge approach to develop feedback from the motor ground circuit to produce a signal to drive amplifiers to power the motor. The circuit automatically compensates for shifts in harmonic frequency of the piezoelectric elements due to pressure and temperature changes.

  20. Short-circuit logic

    NARCIS (Netherlands)

    J.A. Bergstra; A. Ponse

    2010-01-01

    Short-circuit evaluation denotes the semantics of propositional connectives in which the second argument is only evaluated if the first argument does not suffice to determine the value of the expression. In programming, short-circuit evaluation is widely used. A short-circuit logic is a variant of p

  1. Practical microwave circuits

    CERN Document Server

    Maas, Stephen A

    2014-01-01

    This book differentiates itself by presenting microwave and RF technology from a circuit design viewpoint, rather than a set of electromagnetic problems. The emphasis is on gaining a practical understanding of often overlooked but vital physical processes.This resource provides microwave circuit engineers with analytical techniques for understanding and designing high-frequency circuits almost entirely from a circuit point of view. Electromagnetic concepts are not avoided, but they are employed only as necessary to support circuit-theoretical ones or to describe phenomena such as radiation and

  2. Exact Threshold Circuits

    DEFF Research Database (Denmark)

    Hansen, Kristoffer Arnsfelt; Podolskii, Vladimir V.

    2010-01-01

    We initiate a systematic study of constant depth Boolean circuits built using exact threshold gates. We consider both unweighted and weighted exact threshold gates and introduce corresponding circuit classes. We next show that this gives a hierarchy of classes that seamlessly interleave with the ......We initiate a systematic study of constant depth Boolean circuits built using exact threshold gates. We consider both unweighted and weighted exact threshold gates and introduce corresponding circuit classes. We next show that this gives a hierarchy of classes that seamlessly interleave...... with the well-studied corresponding hierarchies defined using ordinary threshold gates. A major open problem in Boolean circuit complexity is to provide an explicit super-polynomial lower bound for depth two threshold circuits. We identify the class of depth two exact threshold circuits as a natural subclass...

  3. Feedback in analog circuits

    CERN Document Server

    Ochoa, Agustin

    2016-01-01

    This book describes a consistent and direct methodology to the analysis and design of analog circuits with particular application to circuits containing feedback. The analysis and design of circuits containing feedback is generally presented by either following a series of examples where each circuit is simplified through the use of insight or experience (someone else’s), or a complete nodal-matrix analysis generating lots of algebra. Neither of these approaches leads to gaining insight into the design process easily. The author develops a systematic approach to circuit analysis, the Driving Point Impedance and Signal Flow Graphs (DPI/SFG) method that does not require a-priori insight to the circuit being considered and results in factored analysis supporting the design function. This approach enables designers to account fully for loading and the bi-directional nature of elements both in the feedback path and in the amplifier itself, properties many times assumed negligible and ignored. Feedback circuits a...

  4. Loviisa nuclear power plant analyzer

    International Nuclear Information System (INIS)

    The APROS Simulation Environment has been developed since 1986 by Imatran Voima Oy (IVO) and the Technical Research Centre of Finland (VTT). It provides tools, solution algorithms and process components for use in different simulation systems for design, analysis and training purposes. One of its main nuclear applications is the Loviisa Nuclear Power Plant Analyzer (LPA). The Loviisa Plant Analyzer includes all the important plant components both in the primary and in the secondary circuits. In addition, all the main control systems, the protection system and the high voltage electrical systems are included. (orig.)

  5. Circuit analysis of quantum measurement

    OpenAIRE

    Kurotani, Yuji; Ueda, Masahito

    2006-01-01

    We develop a circuit theory that enables us to analyze quantum measurements on a two-level system and on a continuous-variable system on an equal footing. As a measurement scheme applicable to both systems, we discuss a swapping state measurement which exchanges quantum states between the system and the measuring apparatus before the apparatus meter is read out. This swapping state measurement has an advantage in gravitational-wave detection over contractive state measurement in that the post...

  6. Design, Analysis and Test of Logic Circuits Under Uncertainty

    CERN Document Server

    Krishnaswamy, Smita; Hayes, John P

    2013-01-01

    Integrated circuits (ICs) increasingly exhibit uncertain characteristics due to soft errors, inherently probabilistic devices, and manufacturing variability. As device technologies scale, these effects can be detrimental to the reliability of logic circuits.  To improve future semiconductor designs, this book describes methods for analyzing, designing, and testing circuits subject to probabilistic effects. The authors first develop techniques to model inherently probabilistic methods in logic circuits and to test circuits for determining their reliability after they are manufactured. Then, they study error-masking mechanisms intrinsic to digital circuits and show how to leverage them to design more reliable circuits.  The book describes techniques for:   • Modeling and reasoning about probabilistic behavior in logic circuits, including a matrix-based reliability-analysis framework;   • Accurate analysis of soft-error rate (SER) based on functional-simulation, sufficiently scalable for use in gate-l...

  7. AN ANALYSIS METHOD FOR HIGH-SPEED CIRCUIT SYSTEMS

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    A new method for analyzing high-speed circuit systems is presented. The method adds transmission line end currents to the circuit variables of the classical modified nodal approach. Then the matrix equation describing high-speed circuit system can be formulated directly and analyzed conveniently for its normative form. A time-domain analysis method for transmission lines is also introduced. The two methods are combined together to efficiently analyze high-speed circuit systems having general transmission lines. Numerical experiment is presented and the results are compared with that calculated by Hspice.

  8. Analog circuits cookbook

    CERN Document Server

    Hickman, Ian

    2013-01-01

    Analog Circuits Cookbook presents articles about advanced circuit techniques, components and concepts, useful IC for analog signal processing in the audio range, direct digital synthesis, and ingenious video op-amp. The book also includes articles about amplitude measurements on RF signals, linear optical imager, power supplies and devices, and RF circuits and techniques. Professionals and students of electrical engineering will find the book informative and useful.

  9. Stochastic Switching Circuit Synthesis

    OpenAIRE

    Wilhelm, Daniel; Bruck, Jehoshua

    2009-01-01

    Shannon in his 1938 Masterpsilas Thesis demonstrated that any Boolean function can be realized by a switching relay circuit, leading to the development of deterministic digital logic. Here, we replace each classical switch with a probabilistic switch (pswitch). We present algorithms for synthesizing circuits closed with a desired probability, including an algorithm that generates optimal size circuits for any binary fraction. We also introduce a new duality property for series-parallel stocha...

  10. Regenerative feedback resonant circuit

    Science.gov (United States)

    Jones, A. Mark; Kelly, James F.; McCloy, John S.; McMakin, Douglas L.

    2014-09-02

    A regenerative feedback resonant circuit for measuring a transient response in a loop is disclosed. The circuit includes an amplifier for generating a signal in the loop. The circuit further includes a resonator having a resonant cavity and a material located within the cavity. The signal sent into the resonator produces a resonant frequency. A variation of the resonant frequency due to perturbations in electromagnetic properties of the material is measured.

  11. Analog circuit design

    CERN Document Server

    Dobkin, Bob

    2012-01-01

    Analog circuit and system design today is more essential than ever before. With the growth of digital systems, wireless communications, complex industrial and automotive systems, designers are being challenged to develop sophisticated analog solutions. This comprehensive source book of circuit design solutions aids engineers with elegant and practical design techniques that focus on common analog challenges. The book's in-depth application examples provide insight into circuit design and application solutions that you can apply in today's demanding designs. <

  12. Transformer Short Circuit Current Calculation and Solutions

    OpenAIRE

    Song, Ling

    2013-01-01

    There are three goals for the thesis. The first one is to introduce types of short-circuits. The second one is to introduce the transformer short-circuit current calculations. And the last one is to find suitable reinforcement methods for the transformers which are running now. Using a comparative approach to analytic research, the advantages and disadvantages of different reinforcement methods can be analyzed. The result shows that the neutral reactor is the best choice to reinforce the S/C ...

  13. Signal sampling circuit

    OpenAIRE

    Louwsma, Simon Minze; Vertregt, Maarten

    2011-01-01

    A sampling circuit for sampling a signal is disclosed. The sampling circuit comprises a plurality of sampling channels adapted to sample the signal in time-multiplexed fashion, each sampling channel comprising a respective track-and-hold circuit connected to a respective analogue to digital converter via a respective output switch. The output switch of each channel opens for a tracking time period when the track-and-hold circuit is in a tracking mode for sampling the signal, and closes for a ...

  14. Electronic devices and circuits

    CERN Document Server

    Pridham, Gordon John

    1968-01-01

    Electronic Devices and Circuits, Volume 1 deals with the design and applications of electronic devices and circuits such as passive components, diodes, triodes and transistors, rectification and power supplies, amplifying circuits, electronic instruments, and oscillators. These topics are supported with introductory network theory and physics. This volume is comprised of nine chapters and begins by explaining the operation of resistive, inductive, and capacitive elements in direct and alternating current circuits. The theory for some of the expressions quoted in later chapters is presented. Th

  15. Security electronics circuits manual

    CERN Document Server

    MARSTON, R M

    1998-01-01

    Security Electronics Circuits Manual is an invaluable guide for engineers and technicians in the security industry. It will also prove to be a useful guide for students and experimenters, as well as providing experienced amateurs and DIY enthusiasts with numerous ideas to protect their homes, businesses and properties.As with all Ray Marston's Circuits Manuals, the style is easy-to-read and non-mathematical, with the emphasis firmly on practical applications, circuits and design ideas. The ICs and other devices used in the practical circuits are modestly priced and readily available ty

  16. CMOS circuits manual

    CERN Document Server

    Marston, R M

    1995-01-01

    CMOS Circuits Manual is a user's guide for CMOS. The book emphasizes the practical aspects of CMOS and provides circuits, tables, and graphs to further relate the fundamentals with the applications. The text first discusses the basic principles and characteristics of the CMOS devices. The succeeding chapters detail the types of CMOS IC, including simple inverter, gate and logic ICs and circuits, and complex counters and decoders. The last chapter presents a miscellaneous collection of two dozen useful CMOS circuits. The book will be useful to researchers and professionals who employ CMOS circu

  17. Timergenerator circuits manual

    CERN Document Server

    Marston, R M

    2013-01-01

    Timer/Generator Circuits Manual is an 11-chapter text that deals mainly with waveform generator techniques and circuits. Each chapter starts with an explanation of the basic principles of its subject followed by a wide range of practical circuit designs. This work presents a total of over 300 practical circuits, diagrams, and tables.Chapter 1 outlines the basic principles and the different types of generator. Chapters 2 to 9 deal with a specific type of waveform generator, including sine, square, triangular, sawtooth, and special waveform generators pulse. These chapters also include pulse gen

  18. Circuits and filters handbook

    CERN Document Server

    Chen, Wai-Kai

    2003-01-01

    A bestseller in its first edition, The Circuits and Filters Handbook has been thoroughly updated to provide the most current, most comprehensive information available in both the classical and emerging fields of circuits and filters, both analog and digital. This edition contains 29 new chapters, with significant additions in the areas of computer-aided design, circuit simulation, VLSI circuits, design automation, and active and digital filters. It will undoubtedly take its place as the engineer's first choice in looking for solutions to problems encountered in the design, analysis, and behavi

  19. MOS integrated circuit design

    CERN Document Server

    Wolfendale, E

    2013-01-01

    MOS Integral Circuit Design aims to help in the design of integrated circuits, especially large-scale ones, using MOS Technology through teaching of techniques, practical applications, and examples. The book covers topics such as design equation and process parameters; MOS static and dynamic circuits; logic design techniques, system partitioning, and layout techniques. Also featured are computer aids such as logic simulation and mask layout, as well as examples on simple MOS design. The text is recommended for electrical engineers who would like to know how to use MOS for integral circuit desi

  20. Quantum Circuits with Mixed States

    CERN Document Server

    Aharonov, D; Nisan, N; Aharonov, Dorit; Kitaev, Alexei; Nisan, Noam

    1998-01-01

    We define the model of quantum circuits with density matrices, where non-unitary gates are allowed. Measurements in the middle of the computation, noise and decoherence are implemented in a natural way in this model, which is shown to be equivalent in computational power to standard quantum circuits. The main result in this paper is a solution for the subroutine problem: The general function that a quantum circuit outputs is a probabilistic function, but using pure state language, such a function can not be used as a black box in other computations. We give a natural definition of using general subroutines, and analyze their computational power. We suggest convenient metrics for quantum computing with mixed states. For density matrices we analyze the so called ``trace metric'', and using this metric, we define and discuss the ``diamond metric'' on superoperators. These metrics enable a formal discussion of errors in the computation. Using a ``causality'' lemma for density matrices, we also prove a simple lowe...

  1. Inter Digital Transducer Modelling through Mason Equivalent Circuit Model

    DEFF Research Database (Denmark)

    Mishra, Dipti; Singh, Abhishek; Hussain, Dil muhammed Akbar;

    2016-01-01

    by Simulation program with Integrated Circuit Emphasis (HSPICE), a well-liked electronic path simulator. The acoustic wave devices are not suitable to simulation through circuit simulator.In this paper, an electrical model of Mason’s Equivalent electricalcircuit for an inter-digital transducer (IDT......The frequency reliance of inter-digital transducer is analyzed with the help of MASON’s Equivalent circuit which is based on Smith’s Equivalent circuit which is further based on Foster’sNetwork. An inter-digital transducer has been demonstratedas a RLC network. The circuit is simulated...

  2. A Virtual Circuits Lab

    Science.gov (United States)

    Vick, Matthew E.

    2010-01-01

    The University of Colorado's Physics Education Technology (PhET) website offers free, high-quality simulations of many physics experiments that can be used in the classroom. The Circuit Construction Kit, for example, allows students to safely and constructively play with circuit components while learning the mathematics behind many circuit…

  3. Synchronizing Hyperchaotic Circuits

    DEFF Research Database (Denmark)

    Tamasevicius, Arunas; Cenys, Antanas; Namajunas, Audrius;

    1997-01-01

    Regarding possible applications to secure communications the technique of synchronizing hyperchaotic circuits with a single dynamical variable is discussed. Several specific examples including the fourth-order circuits with two positive Lyapunov exponents as well as the oscillator with a delay line...

  4. Electrical spectrum & network analyzers a practical approach

    CERN Document Server

    Helfrick, Albert D

    1991-01-01

    This book presents fundamentals and the latest techniques of electrical spectrum analysis. It focuses on instruments and techniques used on spectrum and network analysis, rather than theory. The book covers the use of spectrum analyzers, tracking generators, and network analyzers. Filled with practical examples, the book presents techniques that are widely used in signal processing and communications applications, yet are difficult to find in most literature.Key Features* Presents numerous practical examples, including actual spectrum analyzer circuits* Instruction on how to us

  5. Performance Analysis of Modified QSERL Circuit

    Directory of Open Access Journals (Sweden)

    Shipra Upadhyay

    2013-08-01

    Full Text Available This work is based on a new approach for minimizing energy consumption in quasi static energy recoverylogic (QSERL circuit which involves optimization by removing the non adiabatic losses completely.Energy recovering circuitry based on adiabatic principles is a promising technique leading towards lowpowerhigh performance circuit design. The efficiency of such circuits may be increased by reducing theadiabatic and non-adiabatic losses drawn by them during the charging and recovery operations. In thispaper, performance of the proposed logic style is analyzed and compared with CMOS in theirrepresentative inverters, gates, flip flops and adder circuits. All the circuits were simulated by VIRTUOSOSPECTRE simulator of Cadence in 0.18μm technology. In our proposed inverter the energy efficiency hasbeen improved to almost 30% & 20% upto 20MHz and 20fF external load capacitance in comparison toCMOS & QSERL circuits respectively. Our proposed circuit provides energy efficient performance up to100 MHz and thus it has proven to be used in high-performance VLSI circuitry.

  6. Digital Microfluidics Sample Analyzer

    Science.gov (United States)

    Pollack, Michael G.; Srinivasan, Vijay; Eckhardt, Allen; Paik, Philip Y.; Sudarsan, Arjun; Shenderov, Alex; Hua, Zhishan; Pamula, Vamsee K.

    2010-01-01

    Three innovations address the needs of the medical world with regard to microfluidic manipulation and testing of physiological samples in ways that can benefit point-of-care needs for patients such as premature infants, for which drawing of blood for continuous tests can be life-threatening in their own right, and for expedited results. A chip with sample injection elements, reservoirs (and waste), droplet formation structures, fluidic pathways, mixing areas, and optical detection sites, was fabricated to test the various components of the microfluidic platform, both individually and in integrated fashion. The droplet control system permits a user to control droplet microactuator system functions, such as droplet operations and detector operations. Also, the programming system allows a user to develop software routines for controlling droplet microactuator system functions, such as droplet operations and detector operations. A chip is incorporated into the system with a controller, a detector, input and output devices, and software. A novel filler fluid formulation is used for the transport of droplets with high protein concentrations. Novel assemblies for detection of photons from an on-chip droplet are present, as well as novel systems for conducting various assays, such as immunoassays and PCR (polymerase chain reaction). The lab-on-a-chip (a.k.a., lab-on-a-printed-circuit board) processes physiological samples and comprises a system for automated, multi-analyte measurements using sub-microliter samples of human serum. The invention also relates to a diagnostic chip and system including the chip that performs many of the routine operations of a central labbased chemistry analyzer, integrating, for example, colorimetric assays (e.g., for proteins), chemiluminescence/fluorescence assays (e.g., for enzymes, electrolytes, and gases), and/or conductometric assays (e.g., for hematocrit on plasma and whole blood) on a single chip platform.

  7. Approximate circuits for increased reliability

    Energy Technology Data Exchange (ETDEWEB)

    Hamlet, Jason R.; Mayo, Jackson R.

    2015-12-22

    Embodiments of the invention describe a Boolean circuit having a voter circuit and a plurality of approximate circuits each based, at least in part, on a reference circuit. The approximate circuits are each to generate one or more output signals based on values of received input signals. The voter circuit is to receive the one or more output signals generated by each of the approximate circuits, and is to output one or more signals corresponding to a majority value of the received signals. At least some of the approximate circuits are to generate an output value different than the reference circuit for one or more input signal values; however, for each possible input signal value, the majority values of the one or more output signals generated by the approximate circuits and received by the voter circuit correspond to output signal result values of the reference circuit.

  8. Approximate circuits for increased reliability

    Energy Technology Data Exchange (ETDEWEB)

    Hamlet, Jason R.; Mayo, Jackson R.

    2015-08-18

    Embodiments of the invention describe a Boolean circuit having a voter circuit and a plurality of approximate circuits each based, at least in part, on a reference circuit. The approximate circuits are each to generate one or more output signals based on values of received input signals. The voter circuit is to receive the one or more output signals generated by each of the approximate circuits, and is to output one or more signals corresponding to a majority value of the received signals. At least some of the approximate circuits are to generate an output value different than the reference circuit for one or more input signal values; however, for each possible input signal value, the majority values of the one or more output signals generated by the approximate circuits and received by the voter circuit correspond to output signal result values of the reference circuit.

  9. Optoelectronics circuits manual

    CERN Document Server

    Marston, R M

    2013-01-01

    Optoelectronics Circuits Manual covers the basic principles and characteristics of the best known types of optoelectronic devices, as well as the practical applications of many of these optoelectronic devices. The book describes LED display circuits and LED dot- and bar-graph circuits and discusses the applications of seven-segment displays, light-sensitive devices, optocouplers, and a variety of brightness control techniques. The text also tackles infrared light-beam alarms and multichannel remote control systems. The book provides practical user information and circuitry and illustrations.

  10. Circuit analysis with Multisim

    CERN Document Server

    Baez-Lopez, David

    2011-01-01

    This book is concerned with circuit simulation using National Instruments Multisim. It focuses on the use and comprehension of the working techniques for electrical and electronic circuit simulation. The first chapters are devoted to basic circuit analysis.It starts by describing in detail how to perform a DC analysis using only resistors and independent and controlled sources. Then, it introduces capacitors and inductors to make a transient analysis. In the case of transient analysis, it is possible to have an initial condition either in the capacitor voltage or in the inductor current, or bo

  11. Troubleshooting analog circuits

    CERN Document Server

    Pease, Robert A

    1991-01-01

    Troubleshooting Analog Circuits is a guidebook for solving product or process related problems in analog circuits. The book also provides advice in selecting equipment, preventing problems, and general tips. The coverage of the book includes the philosophy of troubleshooting; the modes of failure of various components; and preventive measures. The text also deals with the active components of analog circuits, including diodes and rectifiers, optically coupled devices, solar cells, and batteries. The book will be of great use to both students and practitioners of electronics engineering. Other

  12. Load testing circuit

    DEFF Research Database (Denmark)

    2009-01-01

    A load testing circuit a circuit tests the load impedance of a load connected to an amplifier. The load impedance includes a first terminal and a second terminal, the load testing circuit comprising a signal generator providing a test signal of a defined bandwidth to the first terminal of the load...... impedance, an energy-storing element being connected to the second terminal of the load impedance and providing an output signal, and a measuring unit that measures the output signal or compares the output signal with a reference....

  13. Modern TTL circuits manual

    CERN Document Server

    Marston, R M

    2013-01-01

    Modern TTL Circuits Manual provides an introduction to the basic principles of Transistor-Transistor Logic (TTL). This book outlines the major features of the 74 series of integrated circuits (ICs) and introduces the various sub-groups of the TTL family.Organized into seven chapters, this book begins with an overview of the basics of digital ICs. This text then examines the symbology and mathematics of digital logic. Other chapters consider a variety of topics, including waveform generator circuitry, clocked flip-flop and counter circuits, special counter/dividers, registers, data latches, com

  14. Plasmonic Nanoguides and Circuits

    CERN Document Server

    Bozhevolnyi, Sergey

    2008-01-01

    Modern communication systems dealing with huge amounts of data at ever increasing speed try to utilize the best aspects of electronic and optical circuits. Electronic circuits are tiny but their operation speed is limited, whereas optical circuits are extremely fast but their sizes are limited by diffraction. Waveguide components utilizing surface plasmon (SP) modes were found to combine the huge optical bandwidth and compactness of electronics, and plasmonics thereby began to be considered as the next chip-scale technology. In this book, the authors concentrate on the SP waveguide configurati

  15. Pragmatic circuits frequency domain

    CERN Document Server

    Eccles, William

    2006-01-01

    Pragmatic Circuits: Frequency Domain goes through the Laplace transform to get from the time domain to topics that include the s-plane, Bode diagrams, and the sinusoidal steady state. This second of three volumes ends with a-c power, which, although it is just a special case of the sinusoidal steady state, is an important topic with unique techniques and terminology. Pragmatic Circuits: Frequency Domain is focused on the frequency domain. In other words, time will no longer be the independent variable in our analysis. The two other volumes in the Pragmatic Circuits series include titles on DC

  16. Monolithic microwave integrated circuits

    Science.gov (United States)

    Pucel, R. A.

    Monolithic microwave integrated circuits (MMICs), a new microwave technology which is expected to exert a profound influence on microwave circuit designs for future military systems as well as for the commercial and consumer markets, is discussed. The book contains an historical discussion followed by a comprehensive review presenting the current status in the field. The general topics of the volume are: design considerations, materials and processing considerations, monolithic circuit applications, and CAD, measurement, and packaging techniques. All phases of MMIC technology are covered, from design to testing.

  17. Counting rate logarithmic circuits

    International Nuclear Information System (INIS)

    This paper describes the basic circuit and the design method for a multidecade logarithmic counting ratemeter. The method is based on the charging and discharging of several RC time constants. An F.E.T. switch is used and the drain current is converted into a proportional voltage by a current to voltage converter. The logarithmic linearity was estimated for 4 decades starting from 50 cps. This circuit can be used in several nuclear instruments like survey meters and counting systems. This circuits has been developed as part of campbell channel instrumentation. (author)

  18. Printed circuit for ATLAS

    CERN Multimedia

    Laurent Guiraud

    1999-01-01

    A printed circuit board made by scientists in the ATLAS collaboration for the transition radiaton tracker (TRT). This will read data produced when a high energy particle crosses the boundary between two materials with different electrical properties.

  19. Synthetic in vitro circuits

    OpenAIRE

    Hockenberry, Adam J.; Jewett, Michael C.

    2012-01-01

    Inspired by advances in the ability to construct programmable circuits in living organisms, in vitro circuits are emerging as a viable platform for designing, understanding, and exploiting dynamic biochemical circuitry. In vitro systems allow researchers to directly access and manipulate biomolecular parts without the unwieldy complexity and intertwined dependencies that often exist in vivo. Experimental and computational foundations in DNA, DNA/RNA, and DNA/RNA/protein based circuitry have g...

  20. Multi-qubit circuit quantum electrodynamics

    Energy Technology Data Exchange (ETDEWEB)

    Viehmann, Oliver

    2013-09-03

    Circuit QED systems are macroscopic, man-made quantum systems in which superconducting artificial atoms, also called Josephson qubits, interact with a quantized electromagnetic field. These systems have been devised to mimic the physics of elementary quantum optical systems with real atoms in a scalable and more flexible framework. This opens up a variety of possible applications of circuit QED systems. For instance, they provide a promising platform for processing quantum information. Recent years have seen rapid experimental progress on these systems, and experiments with multi-component circuit QED architectures are currently starting to come within reach. In this thesis, circuit QED systems with multiple Josephson qubits are studied theoretically. We focus on simple and experimentally realistic extensions of the currently operated circuit QED setups and pursue investigations in two main directions. First, we consider the equilibrium behavior of circuit QED systems containing a large number of mutually noninteracting Josephson charge qubits. The currently accepted standard description of circuit QED predicts the possibility of superradiant phase transitions in such systems. However, a full microscopic treatment shows that a no-go theorem for superradiant phase transitions known from atomic physics applies to circuit QED systems as well. This reveals previously unknown limitations of the applicability of the standard theory of circuit QED to multi-qubit systems. Second, we explore the potential of circuit QED for quantum simulations of interacting quantum many-body systems. We propose and analyze a circuit QED architecture that implements the quantum Ising chain in a time-dependent transverse magnetic field. Our setup can be used to study quench dynamics, the propagation of localized excitations, and other non-equilibrium features in this paradigmatic model in the theory of non-equilibrium thermodynamics and quantumcritical phenomena. The setup is based on a

  1. Multi-qubit circuit quantum electrodynamics

    International Nuclear Information System (INIS)

    Circuit QED systems are macroscopic, man-made quantum systems in which superconducting artificial atoms, also called Josephson qubits, interact with a quantized electromagnetic field. These systems have been devised to mimic the physics of elementary quantum optical systems with real atoms in a scalable and more flexible framework. This opens up a variety of possible applications of circuit QED systems. For instance, they provide a promising platform for processing quantum information. Recent years have seen rapid experimental progress on these systems, and experiments with multi-component circuit QED architectures are currently starting to come within reach. In this thesis, circuit QED systems with multiple Josephson qubits are studied theoretically. We focus on simple and experimentally realistic extensions of the currently operated circuit QED setups and pursue investigations in two main directions. First, we consider the equilibrium behavior of circuit QED systems containing a large number of mutually noninteracting Josephson charge qubits. The currently accepted standard description of circuit QED predicts the possibility of superradiant phase transitions in such systems. However, a full microscopic treatment shows that a no-go theorem for superradiant phase transitions known from atomic physics applies to circuit QED systems as well. This reveals previously unknown limitations of the applicability of the standard theory of circuit QED to multi-qubit systems. Second, we explore the potential of circuit QED for quantum simulations of interacting quantum many-body systems. We propose and analyze a circuit QED architecture that implements the quantum Ising chain in a time-dependent transverse magnetic field. Our setup can be used to study quench dynamics, the propagation of localized excitations, and other non-equilibrium features in this paradigmatic model in the theory of non-equilibrium thermodynamics and quantumcritical phenomena. The setup is based on a

  2. Fractal AC circuits and propagating waves on fractals

    CERN Document Server

    Akkermans, Eric; Dunne, Gerald; Rogers, Luke G; Teplyaev, Alexander

    2015-01-01

    We extend Feynman's analysis of the infinite ladder AC circuit to fractal AC circuits. We show that the characteristic impedances can have positive real part even though all the individual impedances inside the circuit are purely imaginary. This provides a physical setting for analyzing wave propagation of signals on fractals, by analogy with the Telegrapher's Equation, and generalizes the real resistance metric on a fractal, which provides a measure of distance on a fractal, to complex impedances.

  3. Peak reading detector circuit

    International Nuclear Information System (INIS)

    The peak reading detector circuit serves for picking up the instants during which peaks of a given polarity occur in sequences of signals in which the extreme values, their time intervals, and the curve shape of the signals vary. The signal sequences appear in measuring the foetal heart beat frequence from amplitude-modulated ultrasonic, electrocardiagram, and blood pressure signals. In order to prevent undesired emission of output signals from, e. g., disturbing intermediate extreme values, the circuit consists of the series connections of a circuit to simulate an ideal diode, a strong unit, a discriminator for the direction of charging current, a time-delay circuit, and an electronic switch lying in the decharging circuit of the storage unit. The time-delay circuit thereby causes storing of a preliminary maximum value being used only after a certain time delay for the emission of the output signal. If a larger extreme value occurs during the delay time the preliminary maximum value is cleared and the delay time starts running anew. (DG/PB)

  4. Bond-graph Methods for Electric Circuits Analysis

    Directory of Open Access Journals (Sweden)

    GRAVA Adriana

    2012-10-01

    Full Text Available The paper presents a bond-graph method for solving and analyzing an electric circuit with four or more circuit loops. Using this method, the time for circuit analysis is much shorter then using a classicalmethod. Besides determining the intensities of electrical currents through the sides of the circuit, the bond-graphs provide the possibility to obtain the transmittance of the analyzed system applying a fast working method. The main advantage of bond-graphs is the interaction with various areas of physics. The analyzedelectrical circuit could be a part of a complex physical system that could be modeled and analyzed as a unitary system by using bond-graphs.

  5. A semiconductor laser excitation circuit

    Energy Technology Data Exchange (ETDEWEB)

    Kaadzunari, O.; Masaty, K.

    1984-03-27

    A semiconductor laser excitation circuit is patented that is designed for operation in a pulsed mode with a high pulse repetition frequency. This circuit includes, in addition to a semiconductor laser, a high speed photodetector, a reference voltage source, a comparator, and a pulse oscillator and modulator. If the circuit is built using standard silicon integrated circuits, its speed amounts to several hundred megahertz, if it is constructed using gallium arsenide integrated circuits, its speed is several gigahertz.

  6. The Mind Grows Circuits

    CERN Document Server

    Panigrahy, Rina

    2012-01-01

    There is a vast supply of prior art that study models for mental processes. Some studies in psychology and philosophy approach it from an inner perspective in terms of experiences and percepts. Others such as neurobiology or connectionist-machines approach it externally by viewing the mind as complex circuit of neurons where each neuron is a primitive binary circuit. In this paper, we also model the mind as a place where a circuit grows, starting as a collection of primitive components at birth and then builds up incrementally in a bottom up fashion. A new node is formed by a simple composition of prior nodes when we undergo a repeated experience that can be described by that composition. Unlike neural networks, however, these circuits take "concepts" or "percepts" as inputs and outputs. Thus the growing circuits can be likened to a growing collection of lambda expressions that are built on top of one another in an attempt to compress the sensory input as a heuristic to bound its Kolmogorov Complexity.

  7. Chaotic memristive circuit: equivalent circuit realization and dynamical analysis

    Institute of Scientific and Technical Information of China (English)

    Bao Bo-Cheng; Xu Jian-Ping; Zhou Guo-Hua; Ma Zheng-Hua; Zou Ling

    2011-01-01

    In this paper,a practical equivalent circuit of an active flux-controlled memristor characterized by smooth piecewise-quadratic nonlinearity is designed and an experimental chaotic memristive circuit is implemented.The chaotic memristive circuit has an equilibrium set and its stability is dependent on the initial state of the memristor.The initial state-dependent and the circuit parameter-dependent dynamics of the chaotic memristive circuit are investigated via phase portraits,bifurcation diagrams and Lyapunov exponents.Both experimental and simulation results validate the proposed equivalent circuit realization of the active flux-controlled memristor.

  8. Circuit Quantum Electrodynamics

    CERN Document Server

    Bishop, Lev S

    2010-01-01

    Circuit Quantum Electrodynamics (cQED), the study of the interaction between superconducting circuits behaving as artificial atoms and 1-dimensional transmission-line resonators, has shown much promise for quantum information processing tasks. For the purposes of quantum computing it is usual to approximate the artificial atoms as 2-level qubits, and much effort has been expended on attempts to isolate these qubits from the environment and to invent ever more sophisticated control and measurement schemes. Rather than focussing on these technological aspects of the field, this thesis investigates the opportunities for using these carefully engineered systems for answering questions of fundamental physics.

  9. Electronic circuits fundamentals & applications

    CERN Document Server

    Tooley, Mike

    2015-01-01

    Electronics explained in one volume, using both theoretical and practical applications.New chapter on Raspberry PiCompanion website contains free electronic tools to aid learning for students and a question bank for lecturersPractical investigations and questions within each chapter help reinforce learning Mike Tooley provides all the information required to get to grips with the fundamentals of electronics, detailing the underpinning knowledge necessary to appreciate the operation of a wide range of electronic circuits, including amplifiers, logic circuits, power supplies and oscillators. The

  10. Primer printed circuit boards

    CERN Document Server

    Argyle, Andrew

    2009-01-01

    Step-by-step instructions for making your own PCBs at home. Making your own printed circuit board (PCB) might seem a daunting task, but once you master the steps, it's easy to attain professional-looking results. Printed circuit boards, which connect chips and other components, are what make almost all modern electronic devices possible. PCBs are made from sheets of fiberglass clad with copper, usually in multiplelayers. Cut a computer motherboard in two, for instance, and you'll often see five or more differently patterned layers. Making boards at home is relatively easy

  11. Electronic circuit analysis

    CERN Document Server

    Kishore, K Lal

    2008-01-01

    Second Edition of the book Electronic Circuit Analysis is brought out with certain new Topics and reorganization of text matter into eight units. With addition of new topics, syllabi of many universities in this subject can be covered. Besides this, the book can also meet the requirements of M.Sc (Electronics), AMIETE, AMIE (Electronics) courses. Text matter is improved thoroughly. New topics like frequency effects in multistage amplifiers, amplifier circuit analysis, design of high frequency amplifiers, switching regulators, voltage multipliers, Uninterrupted Power Supplies (UPS), and Switchi

  12. Inrush Current Control Circuit

    Science.gov (United States)

    Cole, Steven W. (Inventor)

    2002-01-01

    An inrush current control circuit having an input terminal connected to a DC power supply and an output terminal connected to a load capacitor limits the inrush current that charges up the load capacitor during power up of a system. When the DC power supply applies a DC voltage to the input terminal, the inrush current control circuit produces a voltage ramp at the load capacitor instead of an abrupt DC voltage. The voltage ramp results in a constant low level current to charge up the load capacitor, greatly reducing the current drain on the DC power supply.

  13. Circuit design for reliability

    CERN Document Server

    Cao, Yu; Wirth, Gilson

    2015-01-01

    This book presents physical understanding, modeling and simulation, on-chip characterization, layout solutions, and design techniques that are effective to enhance the reliability of various circuit units.  The authors provide readers with techniques for state of the art and future technologies, ranging from technology modeling, fault detection and analysis, circuit hardening, and reliability management. Provides comprehensive review on various reliability mechanisms at sub-45nm nodes; Describes practical modeling and characterization techniques for reliability; Includes thorough presentation of robust design techniques for major VLSI design units; Promotes physical understanding with first-principle simulations.

  14. A singularity in Kirchhoff’s circuit equations

    Science.gov (United States)

    Sree Harsha, N. R.

    2016-09-01

    Students often have difficulty in understanding qualitatively the behavior of simple electric circuits. In particular, as different studies have shown, they find multiple batteries connected in multiple loops difficult to analyze. In a recent paper, Sree Harsha et al (2015 Phys. Educ. 50 568), we showed such an electric circuit, which consists of ideal batteries connected in parallel, that could not be solved by the existing circuit analysis methods. In this paper, we shall introduce a new mathematical method for solving simple electric circuits from the solutions of more general circuits and show that the currents, in this particular circuit, take the indeterminate 0/0 form. We shall also present some of the implications of teaching the method. We believe that the description presented in this paper should help instructors in teaching the behavior of multiple batteries connected in parallel.

  15. Small Signal Circuit Model of Double Photodiodes

    Institute of Scientific and Technical Information of China (English)

    HAN Jian-zhong; Ni Guo-qiang; MAO Lu-hong

    2004-01-01

    The transmission delay of photogenerated carriers in a CMOS-process-compatible double photodiode (DPD) is analyzed by using device simulation. The DPD small signal equivalent circuit model which includes transmission delay of photogenerated carriers is given. From analysis on the frequency domain of the circuit model the device has two poles. One has the relationship with junction capacitance and the DPD's load,the other with the depth and the doping concentration of the N-well in the DPD. Different depth of the Nwell and different area of the DPDs with bandwidth were compared. The analysis results are important to design the high speed DPDs.

  16. Optimal design of APD biasing circuit

    Institute of Scientific and Technical Information of China (English)

    SUN Chun-sheng; QIN Shi-qiao; WANG Xing-shu; ZHU Dong-hua

    2007-01-01

    This paper proposes a control method for avalanche photodiode (APD) reverse bias with temperature compensation and load resistance compensation. The influence of background light and load resistance on APD detection circuit is analyzed in detail. A theoretical model of temperature compensation and load resistance compensation is established, which is used for APD biasing circuit designing. It is predicted that this control method is especially suitable for LD laser range finder used on vehicles. Experimental results confirm thatthe design proposed in this paper can considerablely improve the performance of range finder.

  17. Exact two-qubit universal quantum circuit

    CERN Document Server

    Zhang, J; Sastry, S; Whaley, K B; Zhang, Jun; Vala, Jiri; Sastry, Shankar

    2003-01-01

    We provide an analytic way to implement any arbitrary two-qubit unitary operation, given an entangling two-qubit gate together with local gates. This is shown to provide explicit construction of a universal quantum circuit that exactly simulates arbitrary two-qubit gates. Each block in this circuit is given in a closed form solution. We also analyze the efficiency of different entangling gates, and find that exactly half of all the controlled-unitary gates can be used to implement two-qubit operations as efficiently as the commonly used CNOT gate.

  18. Receiver Gain Modulation Circuit

    Science.gov (United States)

    Jones, Hollis; Racette, Paul; Walker, David; Gu, Dazhen

    2011-01-01

    A receiver gain modulation circuit (RGMC) was developed that modulates the power gain of the output of a radiometer receiver with a test signal. As the radiometer receiver switches between calibration noise references, the test signal is mixed with the calibrated noise and thus produces an ensemble set of measurements from which ensemble statistical analysis can be used to extract statistical information about the test signal. The RGMC is an enabling technology of the ensemble detector. As a key component for achieving ensemble detection and analysis, the RGMC has broad aeronautical and space applications. The RGMC can be used to test and develop new calibration algorithms, for example, to detect gain anomalies, and/or correct for slow drifts that affect climate-quality measurements over an accelerated time scale. A generalized approach to analyzing radiometer system designs yields a mathematical treatment of noise reference measurements in calibration algorithms. By treating the measurements from the different noise references as ensemble samples of the receiver state, i.e. receiver gain, a quantitative description of the non-stationary properties of the underlying receiver fluctuations can be derived. Excellent agreement has been obtained between model calculations and radiometric measurements. The mathematical formulation is equivalent to modulating the gain of a stable receiver with an externally generated signal and is the basis for ensemble detection and analysis (EDA). The concept of generating ensemble data sets using an ensemble detector is similar to the ensemble data sets generated as part of ensemble empirical mode decomposition (EEMD) with exception of a key distinguishing factor. EEMD adds noise to the signal under study whereas EDA mixes the signal with calibrated noise. It is mixing with calibrated noise that permits the measurement of temporal-functional variability of uncertainty in the underlying process. The RGMC permits the evaluation of EDA by

  19. Analysis of Short-circuit Characteristics and Calculation of Steady-state Short-circuit Current for DFIG Wind Turbine

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    Large-scale doubly-fed induction generator (DFIG) wind turbines are connected to the grid and required to remain grid-connection during faults, the short-circuit current contributed by the generation has become a significant issue. However, the traditional calculation methods aiming at synchronous generators cannot be directly applied to the DFIG wind turbines. A new method is needed to calculate the short-circuit current required by the planning, protection and control of the power grid. The short-circuit transition of DFIG under symmetrical and asymmetric short-circuit conditions are mathematically deduced, and the short-circuit characteristics of DFIG are analyzed. A new method is proposed to calculate the steady-state short-circuit current of DFIG based on the derived expressions. The time-domain simulations are conducted to verify the accuracy of the proposed method.

  20. ESD analog circuits and design

    CERN Document Server

    Voldman, Steven H

    2014-01-01

    A comprehensive and in-depth review of analog circuit layout, schematic architecture, device, power network and ESD design This book will provide a balanced overview of analog circuit design layout, analog circuit schematic development, architecture of chips, and ESD design.  It will start at an introductory level and will bring the reader right up to the state-of-the-art. Two critical design aspects for analog and power integrated circuits are combined. The first design aspect covers analog circuit design techniques to achieve the desired circuit performance. The second and main aspect pres

  1. Unstable oscillators based hyperchaotic circuit

    DEFF Research Database (Denmark)

    Murali, K.; Tamasevicius, A.; G. Mykolaitis, A.;

    1999-01-01

    A simple 4th order hyperchaotic circuit with unstable oscillators is described. The circuit contains two negative impedance converters, two inductors, two capacitors, a linear resistor and a diode. The Lyapunov exponents are presented to confirm hyperchaotic nature of the oscillations in the circ...... in the circuit. The performance of the circuit is investigated by means of numerical integration of appropriate differential equations, PSPICE simulations, and hardware experiment.......A simple 4th order hyperchaotic circuit with unstable oscillators is described. The circuit contains two negative impedance converters, two inductors, two capacitors, a linear resistor and a diode. The Lyapunov exponents are presented to confirm hyperchaotic nature of the oscillations...

  2. Quantum secure circuit evaluation

    Institute of Scientific and Technical Information of China (English)

    CHEN Huanhuan; LI Bin; ZHUANG Zhenquan

    2004-01-01

    In order to solve the problem of classical secure circuit evaluation, this paper proposes a quantum approach. In this approach, the method of inserting redundant entangled particles and quantum signature has been employed to strengthen the security of the system. Theoretical analysis shows that our solution is secure against classical and quantum attacks.

  3. Superconducting Quantum Circuits

    NARCIS (Netherlands)

    Majer, J.B.

    2002-01-01

    This thesis describes a number of experiments with superconducting cir- cuits containing small Josephson junctions. The circuits are made out of aluminum islands which are interconnected with a very thin insulating alu- minum oxide layer. The connections form a Josephson junction. The current trough

  4. Bioluminescent bioreporter integrated circuit

    Energy Technology Data Exchange (ETDEWEB)

    Simpson, Michael L. (Knoxville, TN); Sayler, Gary S. (Blaine, TN); Paulus, Michael J. (Knoxville, TN)

    2000-01-01

    Disclosed are monolithic bioelectronic devices comprising a bioreporter and an OASIC. These bioluminescent bioreporter integrated circuit are useful in detecting substances such as pollutants, explosives, and heavy-metals residing in inhospitable areas such as groundwater, industrial process vessels, and battlefields. Also disclosed are methods and apparatus for environmental pollutant detection, oil exploration, drug discovery, industrial process control, and hazardous chemical monitoring.

  5. A transition calculus for Boolean functions. [logic circuit analysis

    Science.gov (United States)

    Tucker, J. H.; Bennett, A. W.

    1974-01-01

    A transition calculus is presented for analyzing the effect of input changes on the output of logic circuits. The method is closely related to the Boolean difference, but it is more powerful. Both differentiation and integration are considered.

  6. Analysis of mutual capacitance and inductance of printed circuit

    OpenAIRE

    Ivanov, V. G.

    2014-01-01

    The article analyzes the mutual capacitance and inductance of printed circuit and introduces an evaluation technique for conductor-to-conductor capacitance under electrical connections tracing, the technique based on a multi-layer channel model.

  7. Resistor Combinations for Parallel Circuits.

    Science.gov (United States)

    McTernan, James P.

    1978-01-01

    To help simplify both teaching and learning of parallel circuits, a high school electricity/electronics teacher presents and illustrates the use of tables of values for parallel resistive circuits in which total resistances are whole numbers. (MF)

  8. The LMT circuit and SPICE

    DEFF Research Database (Denmark)

    Lindberg, Erik; Murali, K.; Tamacevicius, Arunas

    2006-01-01

    The state equations of the LMT circuit are modeled as a dedicated analogue computer circuit and solved by means of PSpice. The nonlinear part of the system is studied. Problems with the PSpice program are presented....

  9. Electronic circuits and systems: A compilation. [including integrated circuits, logic circuits, varactor diode circuits, low pass filters, and optical equipment circuits

    Science.gov (United States)

    1975-01-01

    Technological information is presented electronic circuits and systems which have potential utility outside the aerospace community. Topics discussed include circuit components such as filters, converters, and integrators, circuits designed for use with specific equipment or systems, and circuits designed primarily for use with optical equipment or displays.

  10. Diode, transistor & fet circuits manual

    CERN Document Server

    Marston, R M

    2013-01-01

    Diode, Transistor and FET Circuits Manual is a handbook of circuits based on discrete semiconductor components such as diodes, transistors, and FETS. The book also includes diagrams and practical circuits. The book describes basic and special diode characteristics, heat wave-rectifier circuits, transformers, filter capacitors, and rectifier ratings. The text also presents practical applications of associated devices, for example, zeners, varicaps, photodiodes, or LEDs, as well as it describes bipolar transistor characteristics. The transistor can be used in three basic amplifier configuration

  11. Static Switching Dynamic Buffer Circuit

    OpenAIRE

    Pandey, A. K.; R. A. Mishra; R. K. Nagaria

    2013-01-01

    We proposed footless domino logic buffer circuit. It minimizes redundant switching at the dynamic and the output nodes. The proposed circuit avoids propagation of precharge pulse to the output node and allows the dynamic node which saves power consumption. Simulation is done using 0.18 µm CMOS technology. We have calculated the power consumption, delay, and power delay product of the proposed circuit and compared the results with the existing circuits for different logic function, loading co...

  12. Value Constraint and Monotone circuit

    OpenAIRE

    Kobayashi, Koji

    2012-01-01

    This paper talks about that monotone circuit is P-Complete. Decision problem that include P-Complete is mapping that classify input with a similar property. Therefore equivalence relation of input value is important for computation. But monotone circuit cannot compute the equivalence relation of the value because monotone circuit can compute only monotone function. Therefore, I make the value constraint explicitly in the input and monotone circuit can compute equivalence relation. As a result...

  13. Simulation of electronic circuit sensitivity towards humidity using electrochemical data on water layer

    DEFF Research Database (Denmark)

    Joshy, Salil; Verdingovas, Vadimas; Jellesen, Morten Stendahl;

    2015-01-01

    the effect on circuit and PCBA (printed circuit board assembly) layout design. This paper elucidates a methodology for analyzing the sensitivity of an electronic circuit based on parasitic circuit analysis using data on electrical property of the water layer formed under humid as well as contaminated......Climatic conditions like temperature and humidity have direct influence on the operation of electronic circuits. The effects of temperature on the operation of electronic circuits have been widely investigated, while the effect of humidity and solder flux residues are not well understood including...... conditions. Some commonly used circuits are analyzed as case studies and flux related contaminations of PCBA from process is used as an example to show how different flux chemistry and humidity together compromise the circuit functionality....

  14. Signals and Circuits in the Purkinje Neuron

    Directory of Open Access Journals (Sweden)

    Ze'ev R Abrams

    2011-09-01

    Full Text Available Purkinje neurons in the cerebellum have over 100,000 inputs organized in an orthogonal geometry, and a single output channel. As the sole output of the cerebellar cortex layer, their complex firing pattern has been associated with motor control and learning. As such they have been extensively modeled and measured using tools ranging from electrophysiology and neuroanatomy, to dynamic systems and artificial intelligence methods. However, there is an alternative approach to analyze and describe the neuronal output of these cells using concepts from Electrical Engineering, particularly signal processing and digital/analog circuits. By viewing the Purkinje neuron as an unknown circuit to be reverse-engineered, we can use the tools that provide the foundations of today’s integrated circuits and communication systems to analyze the Purkinje system at the circuit level. We use Fourier transforms to analyze and isolate the inherent frequency modes in the Purkinje neuron and define 3 unique frequency ranges associated with the cells’ output. Comparing the Purkinje neuron to a signal generator that can be externally modulated adds an entire level of complexity to the functional role of these neurons both in terms of data analysis and information processing, relying on Fourier analysis methods in place of statistical ones. We also re-describe some of the recent literature in the field, using the nomenclature of signal processing. Furthermore, by comparing the experimental data of the past decade with basic electronic circuitry, we can resolve the outstanding controversy in the field, by recognizing that the Purkinje neuron can act as a multivibrator circuit.

  15. A gas filter correlation analyzer for methane

    Science.gov (United States)

    Sebacher, D. I.

    1978-01-01

    A fast-response instrument for monitoring CH4 was designed and tested using a modified nondispersive infrared technique. An analysis of the single-beam rotating-cell system is presented along with the signal processing circuit. A calibration of the instrument shows that the technique can be used to measure CH4 concentrations as small as 5 ppm-m and the effects of interfering gases are analyzed.

  16. Cosimulation of electromagnetics-circuit systems exploiting DGTD and MNA

    KAUST Repository

    Li, Ping

    2014-06-01

    A hybrid electromagnetics (EM)-circuit simulator exploiting the discontinuous Galerkin time domain (DGTD) method and the modified nodal analysis (MNA) algorithm is developed for analyzing hybrid distributive and nonlinear multiport lumped circuit systems. The computational domain is split into two subsystems. One is the EM subsystem that is analyzed by DGTD, while the other is the circuit subsystem that is solved by the MNA method. The coupling between the EM and circuit subsystems is enforced at the lumped port where related field and circuit unknowns are coupled via the use of numerical flux, port voltages, and current sources. Since the spatial operations of DGTD are localized, thanks to the use of numerical flux, coupling matrices between EM and circuit subsystems are small and are directly inverted. To handle nonlinear devices within the circuit subsystem, the standard Newton-Raphson method is applied to the nonlinear coupling matrix system. In addition, a local time-stepping scheme is applied to improve the efficiency of the hybrid solver. Numerical examples including single and multiport linear/nonlinear circuit networks are presented to validate the proposed solver. © 2014 IEEE.

  17. LC-Circuit Calorimetry

    CERN Document Server

    Bossen, Olaf

    2011-01-01

    We present a new type of calorimeter in which we couple an unknown heat capacity with the aid of Peltier elements to an electrical circuit. The use of an electrical inductance and an amplifier in the circuit allows us to achieve autonomous oscillations, and the measurement of the corresponding resonance frequency makes it possible to accurately measure the heat capacity with an intrinsic statistical error that decreases as ~t^{-3/2} with measuring time t, as opposed to a corresponding error ~t^{-1/2} in the conventional alternating current (a.c.) method to measure heat capacities. We have built a demonstration experiment to show the feasibility of the new technique, and we have tested it on a gadolinium sample at its transition to the ferromagnetic state.

  18. Engineering prokaryotic gene circuits

    OpenAIRE

    Michalodimitrakis, Konstantinos; Isalan, Mark

    2009-01-01

    Engineering of synthetic gene circuits is a rapidly growing discipline, currently dominated by prokaryotic transcription networks, which can be easily rearranged or rewired to give different output behaviours. In this review, we examine both a rational and a combinatorial design of such networks and discuss progress on using in vitro evolution techniques to obtain functional systems. Moving beyond pure transcription networks, more and more networks are being implemented at the level of RNA, t...

  19. Refractory Neuron Circuits

    OpenAIRE

    Sarpeshkar, Rahul; Watts, Lloyd; Mead, Carver

    1992-01-01

    Neural networks typically use an abstraction of the behaviour of a biological neuron, in which the continuously varying mean firing rate of the neuron is presumed to carry information about the neuron's time-varying state of excitation. However, the detailed timing of action potentials is known to be important in many biological systems. To build electronic models of such systems, one must have well-characterized neuron circuits that capture the essential behaviour of real neur...

  20. Electronic devices and circuits

    CERN Document Server

    Kishore, K Lal

    2008-01-01

    This book is written in a simple lucid Language along with derivation of equations and supported by numerous solved problems to help the student to understand the concepts clearly.Advances in Miniaturization of Electronic Systems by ever increasing packaging densities on Integrated Circuits has made it very essential for thorough Knowledge of the concepts, phenomenon, characteristics and behaviour of semiconductor Devices for students and professionals.

  1. Cartography of serotonergic circuits.

    Science.gov (United States)

    Sparta, Dennis R; Stuber, Garret D

    2014-08-01

    Serotonin is an essential neuromodulator, but the precise circuit connectivity that regulates serotonergic neurons has not been well defined. Using rabies virus tracing strategies Weissbourd et al. (2014) and Pollak Dorocic et al. (2014) in this issue of Neuron and Ogawa et al. (2014) in Cell Reports provide a comprehensive map of the inputs to serotonergic neurons, highlighting the complexity and diversity of potential upstream cellular regulators.

  2. PARTICLE BEAM TRACKING CIRCUIT

    Science.gov (United States)

    Anderson, O.A.

    1959-05-01

    >A particle-beam tracking and correcting circuit is described. Beam induction electrodes are placed on either side of the beam, and potentials induced by the beam are compared in a voltage comparator or discriminator. This comparison produces an error signal which modifies the fm curve at the voltage applied to the drift tube, thereby returning the orbit to the preferred position. The arrangement serves also to synchronize accelerating frequency and magnetic field growth. (T.R.H.)

  3. Fundamental Atomtronic Circuit Elements

    Science.gov (United States)

    Lee, Jeffrey; McIlvain, Brian; Lobb, Christopher; Hill, Wendell T., III

    2012-06-01

    Recent experiments with neutral superfluid gases have shown that it is possible to create atomtronic circuits analogous to existing superconducting circuits. The goals of these experiments are to create complex systems such as Josephson junctions. In addition, there are theoretical models for active atomtronic components analogous to diodes, transistors and oscillators. In order for any of these devices to function, an understanding of the more fundamental atomtronic elements is needed. Here we describe the first experimental realization of these more fundamental elements. We have created an atomtronic capacitor that is discharged through a resistance and inductance. We will discuss a theoretical description of the system that allows us to determine values for the capacitance, resistance and inductance. The resistance is shown to be analogous to the Sharvin resistance, and the inductance analogous to kinetic inductance in electronics. This atomtronic circuit is implemented with a thermal sample of laser cooled rubidium atoms. The atoms are confined using what we call free-space atom chips, a novel optical dipole trap produced using a generalized phase-contrast imaging technique. We will also discuss progress toward implementing this atomtronic system in a degenerate Bose gas.

  4. The integrated circuit IC EMP transient state disturbance effect experiment method investigates

    International Nuclear Information System (INIS)

    Transient state disturbance characteristic study on the integrated circuit, IC, need from its coupling path outset. Through cable (aerial) coupling, EMP converts to an pulse current voltage and results in the impact to the integrated circuit I/O orifice passing the cable. Aiming at the armament system construction feature, EMP effect to the integrated circuit, IC inside the system is analyzed. The integrated circuit, IC EMP effect experiment current injection method is investigated and a few experiments method is given. (authors)

  5. Changes to the shuttle circuits

    CERN Multimedia

    GS Department

    2011-01-01

    To fit with passengers expectation, there will be some changes to the shuttle circuits as from Monday 10 October. See details on http://cern.ch/ShuttleService (on line on 7 October). Circuit No. 5 is cancelled as circuit No. 1 also stops at Bldg. 33. In order to guarantee shorter travel times, circuit No. 1 will circulate on Meyrin site only and circuit No. 2, with departures from Bldg. 33 and 500, on Prévessin site only. Site Services Section

  6. Power system with an integrated lubrication circuit

    Energy Technology Data Exchange (ETDEWEB)

    Hoff, Brian D. (East Peoria, IL); Akasam, Sivaprasad (Peoria, IL); Algrain, Marcelo C. (Peoria, IL); Johnson, Kris W. (Washington, IL); Lane, William H. (Chillicothe, IL)

    2009-11-10

    A power system includes an engine having a first lubrication circuit and at least one auxiliary power unit having a second lubrication circuit. The first lubrication circuit is in fluid communication with the second lubrication circuit.

  7. Integrated coherent matter wave circuits

    International Nuclear Information System (INIS)

    An integrated coherent matter wave circuit is a single device, analogous to an integrated optical circuit, in which coherent de Broglie waves are created and then launched into waveguides where they can be switched, divided, recombined, and detected as they propagate. Applications of such circuits include guided atom interferometers, atomtronic circuits, and precisely controlled delivery of atoms. We report experiments demonstrating integrated circuits for guided coherent matter waves. The circuit elements are created with the painted potential technique, a form of time-averaged optical dipole potential in which a rapidly moving, tightly focused laser beam exerts forces on atoms through their electric polarizability. Moreover, the source of coherent matter waves is a Bose-Einstein condensate (BEC). Finally, we launch BECs into painted waveguides that guide them around bends and form switches, phase coherent beamsplitters, and closed circuits. These are the basic elements that are needed to engineer arbitrarily complex matter wave circuitry

  8. Memristor based startup circuit for self biased circuits

    Science.gov (United States)

    Das, Mangal; Singh, Amit Kumar; Rathi, Amit; Singhal, Sonal

    2016-04-01

    This paper presents the design of a Memristor based startup circuit for self biased circuits. Memristor has many advantages over conventional CMOS devices such as low leakage current at nanometer scale, easy to manufacture. In this work the switching characteristics of memristor is utilized. First the theoretical equations describing the switching behavior of memristor are investigated. To prove the switching capability of Memristor, a startup circuit based on memristor is proposed which uses series combination of Memristor and capacitor. Proposed circuit is compared with the previously reported MOSFET based startup circuits. Comparison of different circuits was done to validate the results. Simulation results show that memristor based circuit can attain on (I = 12.94 µA) to off state (I = 1 .2 µA) in 25 ns while the MOSFET based startup circuits take on (I = 14.19 µA) to off state (I = 1.4 µA) in more than 90 ns. The benefit comes in terms of area because the number of components used in the circuit are lesser than the conventional startup circuits.

  9. Nonlinear analysis of ring oscillator circuits

    KAUST Repository

    Ge, Xiaoqing

    2010-06-01

    Using nonlinear systems techniques, we analyze the stability properties and synchronization conditions for ring oscillator circuits, which are essential building blocks in digital systems. By making use of its cyclic structure, we investigate local and global stability properties of an n-stage ring oscillator. We present a sufficient condition for global asymptotic stability of the origin and obtain necessity if the ring oscillator consists of identical inverter elements. We then give a synchronization condition for identical interconnected ring oscillators.

  10. Analyzing Impedance Spectroscopy Results

    Institute of Scientific and Technical Information of China (English)

    Yoed Tsur; Sioma Baltianski

    2006-01-01

    In this contribution we briefly discuss several analysis techniques for impedance spectroscopy experiments. A number of different approaches, which differ even by the definition of the problem, are used in the literature. Some aimed towards finding an equivalent circuit. Others aimed towards finding directly dielectric properties of the material under an assumed model. Others towards finding distribution of relaxation times, either parametric or point-by point. No matter what the approach is, this will always be an ill-posed problem in the sense that there exist a large number of possible solutions that solve the problem (mathematically) equally well. Therefore some a-priori knowledge about the system must be used. In addition, we should remember that the ultimate goal is to get physical insight about the system.

  11. Photonic Integrated Circuits

    Science.gov (United States)

    Merritt, Scott; Krainak, Michael

    2016-01-01

    Integrated photonics generally is the integration of multiple lithographically defined photonic and electronic components and devices (e.g. lasers, detectors, waveguides passive structures, modulators, electronic control and optical interconnects) on a single platform with nanometer-scale feature sizes. The development of photonic integrated circuits permits size, weight, power and cost reductions for spacecraft microprocessors, optical communication, processor buses, advanced data processing, and integrated optic science instrument optical systems, subsystems and components. This is particularly critical for small spacecraft platforms. We will give an overview of some NASA applications for integrated photonics.

  12. Optoelectronics circuits manual

    CERN Document Server

    Marston, R M

    1999-01-01

    This manual is a useful single-volume guide specifically aimed at the practical design engineer, technician, and experimenter, as well as the electronics student and amateur. It deals with the subject in an easy to read, down to earth, and non-mathematical yet comprehensive manner, explaining the basic principles and characteristics of the best known devices, and presenting the reader with many practical applications and over 200 circuits. Most of the ICs and other devices used are inexpensive and readily available types, with universally recognised type numbers.The second edition

  13. Electronics circuits and systems

    CERN Document Server

    Bishop, Owen

    2007-01-01

    The material in Electronics - Circuits and Systems is a truly up-to-date textbook, with coverage carefully matched to the electronics units of the 2007 BTEC National Engineering and the latest AS and A Level specifications in Electronics from AQA, OCR and WJEC. The material has been organized with a logical learning progression, making it ideal for a wide range of pre-degree courses in electronics. The approach is student-centred and includes: numerous examples and activities; web research topics; Self Test features, highlighted key facts, formulae and definitions. Each chapter ends with a set

  14. Electric circuits problem solver

    CERN Document Server

    REA, Editors of

    2012-01-01

    Each Problem Solver is an insightful and essential study and solution guide chock-full of clear, concise problem-solving gems. All your questions can be found in one convenient source from one of the most trusted names in reference solution guides. More useful, more practical, and more informative, these study aids are the best review books and textbook companions available. Nothing remotely as comprehensive or as helpful exists in their subject anywhere. Perfect for undergraduate and graduate studies.Here in this highly useful reference is the finest overview of electric circuits currently av

  15. Electronic logic circuits

    CERN Document Server

    Gibson, J

    2013-01-01

    Most branches of organizing utilize digital electronic systems. This book introduces the design of such systems using basic logic elements as the components. The material is presented in a straightforward manner suitable for students of electronic engineering and computer science. The book is also of use to engineers in related disciplines who require a clear introduction to logic circuits. This third edition has been revised to encompass the most recent advances in technology as well as the latest trends in components and notation. It includes a wide coverage of application specific integrate

  16. Electronics circuits and systems

    CERN Document Server

    Bishop, Owen

    2011-01-01

    The material in Electronics - Circuits and Systems is a truly up-to-date textbook, with coverage carefully matched to the electronics units of the 2007 BTEC National Engineering and the latest AS and A Level specifications in Electronics from AQA, OCR and WJEC. The material has been organized with a logical learning progression, making it ideal for a wide range of pre-degree courses in electronics. The approach is student-centred and includes: numerous examples and activities; web research topics; Self Test features, highlighted key facts, formulae and definitions. Ea

  17. Linear integrated circuits

    CERN Document Server

    Carr, Joseph

    1996-01-01

    The linear IC market is large and growing, as is the demand for well trained technicians and engineers who understand how these devices work and how to apply them. Linear Integrated Circuits provides in-depth coverage of the devices and their operation, but not at the expense of practical applications in which linear devices figure prominently. This book is written for a wide readership from FE and first degree students, to hobbyists and professionals.Chapter 1 offers a general introduction that will provide students with the foundations of linear IC technology. From chapter 2 onwa

  18. Nano integrated circuit process

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Yung Sup

    2004-02-15

    This book contains nine chapters, which are introduction of manufacture of semiconductor chip, oxidation such as Dry-oxidation, wet oxidation, oxidation model and oxide film, diffusion like diffusion process, diffusion equation, diffusion coefficient and diffusion system, ion implantation, including ion distribution, channeling, multiimplantation and masking and its system, sputtering such as CVD and PVD, lithography, wet etch and dry etch, interconnection and flattening like metal-silicon connection, silicide, multiple layer metal process and flattening, an integrated circuit process, including MOSFET and CMOS.

  19. Optically controllable molecular logic circuits

    Energy Technology Data Exchange (ETDEWEB)

    Nishimura, Takahiro, E-mail: t-nishimura@ist.osaka-u.ac.jp; Fujii, Ryo; Ogura, Yusuke; Tanida, Jun [Graduate School of Information Science and Technology, Osaka University, 1-5 Yamadaoka, Suita, Osaka 565-0871 (Japan)

    2015-07-06

    Molecular logic circuits represent a promising technology for observation and manipulation of biological systems at the molecular level. However, the implementation of molecular logic circuits for temporal and programmable operation remains challenging. In this paper, we demonstrate an optically controllable logic circuit that uses fluorescence resonance energy transfer (FRET) for signaling. The FRET-based signaling process is modulated by both molecular and optical inputs. Based on the distance dependence of FRET, the FRET pathways required to execute molecular logic operations are formed on a DNA nanostructure as a circuit based on its molecular inputs. In addition, the FRET pathways on the DNA nanostructure are controlled optically, using photoswitching fluorescent molecules to instruct the execution of the desired operation and the related timings. The behavior of the circuit can thus be controlled using external optical signals. As an example, a molecular logic circuit capable of executing two different logic operations was studied. The circuit contains functional DNAs and a DNA scaffold to construct two FRET routes for executing Input 1 AND Input 2 and Input 1 AND NOT Input 3 operations on molecular inputs. The circuit produced the correct outputs with all possible combinations of the inputs by following the light signals. Moreover, the operation execution timings were controlled based on light irradiation and the circuit responded to time-dependent inputs. The experimental results demonstrate that the circuit changes the output for the required operations following the input of temporal light signals.

  20. Optically controllable molecular logic circuits

    International Nuclear Information System (INIS)

    Molecular logic circuits represent a promising technology for observation and manipulation of biological systems at the molecular level. However, the implementation of molecular logic circuits for temporal and programmable operation remains challenging. In this paper, we demonstrate an optically controllable logic circuit that uses fluorescence resonance energy transfer (FRET) for signaling. The FRET-based signaling process is modulated by both molecular and optical inputs. Based on the distance dependence of FRET, the FRET pathways required to execute molecular logic operations are formed on a DNA nanostructure as a circuit based on its molecular inputs. In addition, the FRET pathways on the DNA nanostructure are controlled optically, using photoswitching fluorescent molecules to instruct the execution of the desired operation and the related timings. The behavior of the circuit can thus be controlled using external optical signals. As an example, a molecular logic circuit capable of executing two different logic operations was studied. The circuit contains functional DNAs and a DNA scaffold to construct two FRET routes for executing Input 1 AND Input 2 and Input 1 AND NOT Input 3 operations on molecular inputs. The circuit produced the correct outputs with all possible combinations of the inputs by following the light signals. Moreover, the operation execution timings were controlled based on light irradiation and the circuit responded to time-dependent inputs. The experimental results demonstrate that the circuit changes the output for the required operations following the input of temporal light signals

  1. Sequential circuit design for radiation hardened multiple voltage integrated circuits

    Energy Technology Data Exchange (ETDEWEB)

    Clark, Lawrence T. (Phoenix, AZ); McIver, III, John K. (Albuquerque, NM)

    2009-11-24

    The present invention includes a radiation hardened sequential circuit, such as a bistable circuit, flip-flop or other suitable design that presents substantial immunity to ionizing radiation while simultaneously maintaining a low operating voltage. In one embodiment, the circuit includes a plurality of logic elements that operate on relatively low voltage, and a master and slave latches each having storage elements that operate on a relatively high voltage.

  2. VLSI scaling methods and low power CMOS buffer circuit

    International Nuclear Information System (INIS)

    Device scaling is an important part of the very large scale integration (VLSI) design to boost up the success path of VLSI industry, which results in denser and faster integration of the devices. As technology node moves towards the very deep submicron region, leakage current and circuit reliability become the key issues. Both are increasing with the new technology generation and affecting the performance of the overall logic circuit. The VLSI designers must keep the balance in power dissipation and the circuit's performance with scaling of the devices. In this paper, different scaling methods are studied first. These scaling methods are used to identify the effects of those scaling methods on the power dissipation and propagation delay of the CMOS buffer circuit. For mitigating the power dissipation in scaled devices, we have proposed a reliable leakage reduction low power transmission gate (LPTG) approach and tested it on complementary metal oxide semiconductor (CMOS) buffer circuit. All simulation results are taken on HSPICE tool with Berkeley predictive technology model (BPTM) BSIM4 bulk CMOS files. The LPTG CMOS buffer reduces 95.16% power dissipation with 84.20% improvement in figure of merit at 32 nm technology node. Various process, voltage and temperature variations are analyzed for proving the robustness of the proposed approach. Leakage current uncertainty decreases from 0.91 to 0.43 in the CMOS buffer circuit that causes large circuit reliability. (semiconductor integrated circuits)

  3. Quasi-Linear Circuit

    Science.gov (United States)

    Bradley, William; Bird, Ross; Eldred, Dennis; Zook, Jon; Knowles, Gareth

    2013-01-01

    This work involved developing spacequalifiable switch mode DC/DC power supplies that improve performance with fewer components, and result in elimination of digital components and reduction in magnetics. This design is for missions where systems may be operating under extreme conditions, especially at elevated temperature levels from 200 to 300 degC. Prior art for radiation-tolerant DC/DC converters has been accomplished utilizing classical magnetic-based switch mode converter topologies; however, this requires specific shielding and component de-rating to meet the high-reliability specifications. It requires complex measurement and feedback components, and will not enable automatic re-optimization for larger changes in voltage supply or electrical loading condition. The innovation is a switch mode DC/DC power supply that eliminates the need for processors and most magnetics. It can provide a well-regulated voltage supply with a gain of 1:100 step-up to 8:1 step down, tolerating an up to 30% fluctuation of the voltage supply parameters. The circuit incorporates a ceramic core transformer in a manner that enables it to provide a well-regulated voltage output without use of any processor components or magnetic transformers. The circuit adjusts its internal parameters to re-optimize its performance for changes in supply voltage, environmental conditions, or electrical loading at the output

  4. Simple Cell Balance Circuit

    Science.gov (United States)

    Johnson, Steven D.; Byers, Jerry W.; Martin, James A.

    2012-01-01

    A method has been developed for continuous cell voltage balancing for rechargeable batteries (e.g. lithium ion batteries). A resistor divider chain is provided that generates a set of voltages representing the ideal cell voltage (the voltage of each cell should be as if the cells were perfectly balanced). An operational amplifier circuit with an added current buffer stage generates the ideal voltage with a very high degree of accuracy, using the concept of negative feedback. The ideal voltages are each connected to the corresponding cell through a current- limiting resistance. Over time, having the cell connected to the ideal voltage provides a balancing current that moves the cell voltage very close to that ideal level. In effect, it adjusts the current of each cell during charging, discharging, and standby periods to force the cell voltages to be equal to the ideal voltages generated by the resistor divider. The device also includes solid-state switches that disconnect the circuit from the battery so that it will not discharge the battery during storage. This solution requires relatively few parts and is, therefore, of lower cost and of increased reliability due to the fewer failure modes. Additionally, this design uses very little power. A preliminary model predicts a power usage of 0.18 W for an 8-cell battery. This approach is applicable to a wide range of battery capacities and voltages.

  5. 49 CFR 236.13 - Spring switch; selection of signal control circuits through circuit controller.

    Science.gov (United States)

    2010-10-01

    ... circuits through circuit controller. 236.13 Section 236.13 Transportation Other Regulations Relating to...; selection of signal control circuits through circuit controller. The control circuits of signals governing... circuit controller, or through the contacts of relay repeating the position of such circuit...

  6. Circuit Design of Surface Acoustic Wave Based Micro Force Sensor

    Directory of Open Access Journals (Sweden)

    Yuanyuan Li

    2014-01-01

    Full Text Available Pressure sensors are commonly used in industrial production and mechanical system. However, resistance strain, piezoresistive sensor, and ceramic capacitive pressure sensors possess limitations, especially in micro force measurement. A surface acoustic wave (SAW based micro force sensor is designed in this paper, which is based on the theories of wavelet transform, SAW detection, and pierce oscillator circuits. Using lithium niobate as the basal material, a mathematical model is established to analyze the frequency, and a peripheral circuit is designed to measure the micro force. The SAW based micro force sensor is tested to show the reasonable design of detection circuit and the stability of frequency and amplitude.

  7. Synthetic Biology: Integrated Gene Circuits

    OpenAIRE

    Nandagopal, Nagarajan; Michael B Elowitz

    2011-01-01

    A major goal of synthetic biology is to develop a deeper understanding of biological design principles from the bottom up, by building circuits and studying their behavior in cells. Investigators initially sought to design circuits “from scratch” that functioned as independently as possible from the underlying cellular system. More recently, researchers have begun to develop a new generation of synthetic circuits that integrate more closely with endogenous cellular processes. These approaches...

  8. Quantum Circuits with Mixed States

    OpenAIRE

    Aharonov, Dorit; Kitaev, Alexei; Nisan, Noam

    1998-01-01

    We define the model of quantum circuits with density matrices, where non-unitary gates are allowed. Measurements in the middle of the computation, noise and decoherence are implemented in a natural way in this model, which is shown to be equivalent in computational power to standard quantum circuits. The main result in this paper is a solution for the subroutine problem: The general function that a quantum circuit outputs is a probabilistic function, but using pure state language, such a func...

  9. Pharmacokinetics and RC Circuit Concepts

    Science.gov (United States)

    Cock, Mieke De; Janssen, Paul

    2013-11-01

    Most introductory physics courses include a chapter on RC circuits in which the differential equations for the charging and discharging of a capacitor are derived. A number of papers in this journal describe lab experiments dealing with the measurement of different parameters in such RC circuits. In this contribution, we report on a lab experiment we developed for students majoring in pharmacy, using RC circuits to simulate a pharmacokinetic process.

  10. Designing Parity Preserving Reversible Circuits

    OpenAIRE

    Paul, Goutam; Chattopadhyay, Anupam; Chandak, Chander

    2013-01-01

    Making a reversible circuit fault-tolerant is much more difficult than classical circuit and there have been only a few works in the area of parity-preserving reversible logic design. Moreover, all of these designs are ad hoc, based on some pre-defined parity preserving reversible gates as building blocks. In this paper, we for the first time propose a novel and systematic approach towards parity preserving reversible circuits design. We provide some related theoretical results and give two a...

  11. Macroscopic Quantum Criticality in a Circuit QED

    CERN Document Server

    Wang, Y D; Nori, F; Quan, H T; Sun, C P; Liu, Yu-xi; Nori, Franco

    2006-01-01

    Cavity quantum electrodynamic (QED) is studied for two strongly-coupled charge qubits interacting with a single-mode quantized field, which is provided by a on-chip transmission line resonator. We analyze the dressed state structure of this superconducting circuit QED system and the selection rules of electromagnetic-induced transitions between any two of these dressed states. Its macroscopic quantum criticality, in the form of ground state level crossing, is also analyzed, resulting from competition between the Ising-type inter-qubit coupling and the controllable on-site potentials.

  12. ON NONLINEAR CIRCUIT COMPONENTS WITH N-SHAPED CONDUCTANCE CHARACTERISTICS

    OpenAIRE

    Wey, Todd A.; Ogborn, Lawrence L.

    1995-01-01

    Currently, three-terminal devices with N-shaped I-V characteristics are being fabricated for switching and multi-valued logic applications. The purpose of this study is to investigate switching speed improvements and potential problems of circuit designs employing these nonlinear devices. In this work, both two-terminal and three-terminal devices are analyzed. A design methodology is developed for a second-order twoterminal device circuit and a novel method of I-V characterization is presente...

  13. The Intermodulation Lockin Analyzer

    CERN Document Server

    Tholen, Erik A; Forchheimer, Daniel; Schuler, Vivien; Tholen, Mats O; Hutter, Carsten; Haviland, David B

    2011-01-01

    Nonlinear systems can be probed by driving them with two or more pure tones while measuring the intermodulation products of the drive tones in the response. We describe a digital lock-in analyzer which is designed explicitly for this purpose. The analyzer is implemented on a field-programmable gate array, providing speed in analysis, real-time feedback and stability in operation. The use of the analyzer is demonstrated for Intermodulation Atomic Force Microscopy. A generalization of the intermodulation spectral technique to arbitrary drive waveforms is discussed.

  14. Miniature mass analyzer

    CERN Document Server

    Cuna, C; Lupsa, N; Cuna, S; Tuzson, B

    2003-01-01

    The paper presents the concept of different mass analyzers that were specifically designed as small dimension instruments able to detect with great sensitivity and accuracy the main environmental pollutants. The mass spectrometers are very suited instrument for chemical and isotopic analysis, needed in environmental surveillance. Usually, this is done by sampling the soil, air or water followed by laboratory analysis. To avoid drawbacks caused by sample alteration during the sampling process and transport, the 'in situ' analysis is preferred. Theoretically, any type of mass analyzer can be miniaturized, but some are more appropriate than others. Quadrupole mass filter and trap, magnetic sector, time-of-flight and ion cyclotron mass analyzers can be successfully shrunk, for each of them some performances being sacrificed but we must know which parameters are necessary to be kept unchanged. To satisfy the miniaturization criteria of the analyzer, it is necessary to use asymmetrical geometries, with ion beam obl...

  15. Analyzing in the present

    DEFF Research Database (Denmark)

    Revsbæk, Line; Tanggaard, Lene

    2015-01-01

    the interdependency between researcher and researched. On this basis, we advocate an explicit “open-state-of mind” listening as a key aspect of analyzing qualitative material, often described only as a matter of reading transcribed empirical materials, reading theory, and writing. The article contributes......The article presents a notion of “analyzing in the present” as a source of inspiration in analyzing qualitative research materials. The term emerged from extensive listening to interview recordings during everyday commuting to university campus. Paying attention to the way different parts...... of various interviews conveyed diverse significance to the listening researcher at different times became a method of continuously opening up the empirical material in a reflexive, breakdown-oriented process of analysis. We argue that situating analysis in the present of analyzing emphasizes and acknowledges...

  16. Analyzing binding data.

    Science.gov (United States)

    Motulsky, Harvey J; Neubig, Richard R

    2010-07-01

    Measuring the rate and extent of radioligand binding provides information on the number of binding sites, and their affinity and accessibility of these binding sites for various drugs. This unit explains how to design and analyze such experiments.

  17. Software Design Analyzer System

    Science.gov (United States)

    Tausworthe, R. C.

    1985-01-01

    CRISP80 software design analyzer system a set of programs that supports top-down, hierarchic, modular structured design, and programing methodologies. CRISP80 allows for expression of design as picture of program.

  18. A Circuit to Demonstrate Phase Relationships in "RLC" Circuits

    Science.gov (United States)

    Sokol, P. E.; Warren, G.; Zheng, B.; Smith, P.

    2013-01-01

    We have developed a circuit to demonstrate the phase relationships between resistive and reactive elements in series "RLC" circuits. We utilize a differential amplifier to allow the phases of the three elements and the current to be simultaneously displayed on an inexpensive four channel oscilloscope. We have included a novel circuit…

  19. Memristor Circuits and Systems

    KAUST Repository

    Zidan, Mohammed A.

    2015-05-01

    Current CMOS-based technologies are facing design challenges related to the continuous scaling down of the minimum feature size, according to Moore’s law. Moreover, conventional computing architecture is no longer an effective way of fulfilling modern applications demands, such as big data analysis, pattern recognition, and vector processing. Therefore, there is an exigent need to shift to new technologies, at both the architecture and the device levels. Recently, memristor devices and structures attracted attention for being promising candidates for this job. Memristor device adds a new dimension for designing novel circuits and systems. In addition, high-density memristor-based crossbar is widely considered to be the essential element for future memory and bio-inspired computing systems. However, numerous challenges need to be addressed before the memristor genuinely replaces current memory and computing technologies, which is the motivation behind this research effort. In order to address the technology challenges, we begin by fabricating and modeling the memristor device. The devices fabricated at our local clean room enriched our understanding of the memristive phenomenon and enabled the experimental testing for our memristor-based circuits. Moreover, our proposed mathematical modeling for memristor behavior is an essential element for the theoretical circuit design stage. Designing and addressing the challenges of memristor systems with practical complexity, however, requires an extra step, which takes the form of a reliable and modular simulation platform. We, therefore, built a new simulation platform for the resistive crossbar, which can simulate realistic size arrays filled with real memory data. In addition, this simulation platform includes various crossbar nonidealities in order to obtain accurate simulation results. Consequently, we were able to address the significant challenges facing the high density memristor crossbar, as the building block for

  20. A dishwasher for circuits

    CERN Multimedia

    Rosaria Marraffino

    2014-01-01

    You have always been told that electronic devices fear water. However, at the Surface Mount Devices (SMD) Workshop here at CERN all the electronic assemblies are cleaned with a machine that looks like a… dishwasher.   The circuit dishwasher. Credit: Clara Nellist.  If you think the image above shows a dishwasher, you wouldn’t be completely wrong. Apart from the fact that the whole pumping system and the case itself are made entirely from stainless steel and chemical resistant materials, and the fact that it washes electrical boards instead of dishes… it works exactly like a dishwasher. It’s a professional machine (mainly used in the pharmaceutical industry) designed to clean everything that can be washed with a water-based chemical soap. This type of treatment increases the lifetime of the electronic boards and therefore the LHC's reliability by preventing corrosion problems in the severe radiation and ozone environment of the LHC tunn...

  1. Basic electronic circuits

    CERN Document Server

    Buckley, P M

    1980-01-01

    In the past, the teaching of electricity and electronics has more often than not been carried out from a theoretical and often highly academic standpoint. Fundamentals and basic concepts have often been presented with no indication of their practical appli­ cations, and all too frequently they have been illustrated by artificially contrived laboratory experiments bearing little relationship to the outside world. The course comes in the form of fourteen fairly open-ended constructional experiments or projects. Each experiment has associated with it a construction exercise and an explanation. The basic idea behind this dual presentation is that the student can embark on each circuit following only the briefest possible instructions and that an open-ended approach is thereby not prejudiced by an initial lengthy encounter with the theory behind the project; this being a sure way to dampen enthusiasm at the outset. As the investigation progresses, questions inevitably arise. Descriptions of the phenomena encounte...

  2. Modeling cortical circuits.

    Energy Technology Data Exchange (ETDEWEB)

    Rohrer, Brandon Robinson; Rothganger, Fredrick H.; Verzi, Stephen J.; Xavier, Patrick Gordon

    2010-09-01

    The neocortex is perhaps the highest region of the human brain, where audio and visual perception takes place along with many important cognitive functions. An important research goal is to describe the mechanisms implemented by the neocortex. There is an apparent regularity in the structure of the neocortex [Brodmann 1909, Mountcastle 1957] which may help simplify this task. The work reported here addresses the problem of how to describe the putative repeated units ('cortical circuits') in a manner that is easily understood and manipulated, with the long-term goal of developing a mathematical and algorithmic description of their function. The approach is to reduce each algorithm to an enhanced perceptron-like structure and describe its computation using difference equations. We organize this algorithmic processing into larger structures based on physiological observations, and implement key modeling concepts in software which runs on parallel computing hardware.

  3. Closed Circuit Videoinstallationen

    DEFF Research Database (Denmark)

    Kacunko, Slavko

    be seen with only insignificant qualification as a specific characteristic of the medium. The closed-circuit video installations based on it represent the attest field of experiment for the assumptions on art and the theory and history of the medium that it might lead one make. In recent years......, theoretical debate on the medium has diagnosed with some precision where the electronic video image stands between analogue and digital codes, or again, between media representation and presentation; but that position has hardly ever been subjected to examination against the pertinent examples. An art...... of video as well as the latest digital art forms, can then be examined with the aid of such results and elucidated in historical terms. The prospect at least, of a gradual introduction of the electronic arts into the art history syllabus will be brought a deal closer thanks to such individual...

  4. Diamond Integrated Optomechanical Circuits

    CERN Document Server

    Rath, Patrik; Nebel, Christoph; Wild, Christoph; Pernice, Wolfram H P

    2013-01-01

    Diamond offers unique material advantages for the realization of micro- and nanomechanical resonators due to its high Young's modulus, compatibility with harsh environments and superior thermal properties. At the same time, the wide electronic bandgap of 5.45eV makes diamond a suitable material for integrated optics because of broadband transparency and the absence of free-carrier absorption commonly encountered in silicon photonics. Here we take advantage of both to engineer full-scale optomechanical circuits in diamond thin films. We show that polycrystalline diamond films fabricated by chemical vapour deposition provide a convenient waferscale substrate for the realization of high quality nanophotonic devices. Using free-standing nanomechanical resonators embedded in on-chip Mach-Zehnder interferometers, we demonstrate efficient optomechanical transduction via gradient optical forces. Fabricated diamond resonators reproducibly show high mechanical quality factors up to 11,200. Our low cost, wideband, carri...

  5. VLSI circuits implementing computational models of neocortical circuits.

    Science.gov (United States)

    Wijekoon, Jayawan H B; Dudek, Piotr

    2012-09-15

    This paper overviews the design and implementation of three neuromorphic integrated circuits developed for the COLAMN ("Novel Computing Architecture for Cognitive Systems based on the Laminar Microcircuitry of the Neocortex") project. The circuits are implemented in a standard 0.35 μm CMOS technology and include spiking and bursting neuron models, and synapses with short-term (facilitating/depressing) and long-term (STDP and dopamine-modulated STDP) dynamics. They enable execution of complex nonlinear models in accelerated-time, as compared with biology, and with low power consumption. The neural dynamics are implemented using analogue circuit techniques, with digital asynchronous event-based input and output. The circuits provide configurable hardware blocks that can be used to simulate a variety of neural networks. The paper presents experimental results obtained from the fabricated devices, and discusses the advantages and disadvantages of the analogue circuit approach to computational neural modelling. PMID:22342970

  6. Hybrid quantum circuit with implanted erbium ions

    Energy Technology Data Exchange (ETDEWEB)

    Probst, S.; Rotzinger, H.; Tkalčec, A. [Physikalisches Institut, Karlsruhe Institute of Technology, D-76128 Karlsruhe (Germany); Kukharchyk, N.; Wieck, A. D. [Angewandte Festkörperphysik, Ruhr-Universität Bochum, Universitätsstraße 150, D-44780 Bochum (Germany); Wünsch, S.; Siegel, M. [Institut für Mikro- und Nanoelektronische Systeme, Karlsruhe Institute of Technology, D-76189 Karlsruhe (Germany); Ustinov, A. V. [Physikalisches Institut, Karlsruhe Institute of Technology, D-76128 Karlsruhe (Germany); Laboratory of Superconducting Metamaterials, National University of Science and Technology “MISIS,” Moscow 119049 (Russian Federation); Bushev, P. A. [Experimentalphysik, Universität des Saarlandes, D-66123 Saarbrücken (Germany)

    2014-10-20

    We report on hybrid circuit quantum electrodynamics experiments with focused ion beam implanted Er{sup 3+} ions in Y{sub 2}SiO{sub 5} coupled to an array of superconducting lumped element microwave resonators. The Y{sub 2}SiO{sub 5} crystal is divided into several areas with distinct erbium doping concentrations, each coupled to a separate resonator. The coupling strength is varied from 5 MHz to 18.7 MHz, while the linewidth ranges between 50 MHz and 130 MHz. We confirm the paramagnetic properties of the implanted spin ensemble by evaluating the temperature dependence of the coupling. The efficiency of the implantation process is analyzed and the results are compared to a bulk doped Er:Y{sub 2}SiO{sub 5} sample. We demonstrate the integration of these engineered erbium spin ensembles with superconducting circuits.

  7. Lasing without inversion in circuit quantum electrodynamics.

    Science.gov (United States)

    Marthaler, M; Utsumi, Y; Golubev, D S; Shnirman, A; Schön, Gerd

    2011-08-26

    We study the photon generation in a transmission line oscillator coupled to a driven qubit in the presence of a dissipative electromagnetic environment. It has been demonstrated previously that a population inversion in the qubit can lead to a lasing state of the oscillator. Here we show that the circuit can also exhibit the effect of "lasing without inversion." It arises since the coupling to the dissipative environment enhances photon emission as compared to absorption, similar to the recoil effect predicted for atomic systems. While the recoil effect is very weak, and so far elusive, the effect described here should be observable with realistic circuits. We analyze the requirements for system parameters and environment.

  8. Pharmacokinetics and "RC" Circuit Concepts

    Science.gov (United States)

    De Cock, Mieke; Janssen, Paul

    2013-01-01

    Most introductory physics courses include a chapter on "RC" circuits in which the differential equations for the charging and discharging of a capacitor are derived. A number of papers in this journal describe lab experiments dealing with the measurement of different parameters in such "RC" circuits. In this contribution, we…

  9. Enhancement of Linear Circuit Program

    DEFF Research Database (Denmark)

    Gaunholt, Hans; Dabu, Mihaela; Beldiman, Octavian

    1996-01-01

    In this report a preliminary user friendly interface has been added to the LCP2 program making it possible to describe an electronic circuit by actually drawing the circuit on the screen. Component values and other options and parameters can easily be set by the aid of the interface. The interface...

  10. Demonstrations with an "LCR" Circuit

    Science.gov (United States)

    Kraftmakher, Yaakov

    2011-01-01

    The "LCR" circuit is an important topic in the course of electricity and magnetism. Papers in this field consider mainly the forced oscillations and resonance. Our aim is to show how to demonstrate the free and self-excited oscillations in an "LCR" circuit. (Contains 4 figures.)

  11. Logic Circuit Design Selected Methods

    CERN Document Server

    Vingron, Shimon P

    2012-01-01

        In three main divisions the  book covers combinational circuits, latches, and asynchronous sequential circuits. Combinational circuits have  no memorising ability, while sequential circuits have such an ability to various degrees. Latches are the simplest sequential circuits, ones with the shortest memory. The presentation is decidedly non-standard.         The design of combinational circuits is discussed in an orthodox manner using normal forms and in an unorthodox manner using set-theoretical evaluation formulas relying heavily on Karnaugh maps. The latter approach allows for a new design technique called composition.          Latches are covered very extensively. Their memory functions are expressed mathematically in a time-independent manner allowing the use of (normal, non-temporal) Boolean logic in their calculation. The theory of latches is then used as the basis for calculating asynchronous circuits.         Asynchronous circuits are specified in a tree-representation, eac...

  12. Total organic carbon analyzer

    Science.gov (United States)

    Godec, Richard G.; Kosenka, Paul P.; Smith, Brian D.; Hutte, Richard S.; Webb, Johanna V.; Sauer, Richard L.

    1991-01-01

    The development and testing of a breadboard version of a highly sensitive total-organic-carbon (TOC) analyzer are reported. Attention is given to the system components including the CO2 sensor, oxidation reactor, acidification module, and the sample-inlet system. Research is reported for an experimental reagentless oxidation reactor, and good results are reported for linearity, sensitivity, and selectivity in the CO2 sensor. The TOC analyzer is developed with gravity-independent components and is designed for minimal additions of chemical reagents. The reagentless oxidation reactor is based on electrolysis and UV photolysis and is shown to be potentially useful. The stability of the breadboard instrument is shown to be good on a day-to-day basis, and the analyzer is capable of 5 sample analyses per day for a period of about 80 days. The instrument can provide accurate TOC and TIC measurements over a concentration range of 20 ppb to 50 ppm C.

  13. Analyzing radioligand binding data.

    Science.gov (United States)

    Motulsky, Harvey; Neubig, Richard

    2002-08-01

    Radioligand binding experiments are easy to perform, and provide useful data in many fields. They can be used to study receptor regulation, discover new drugs by screening for compounds that compete with high affinity for radioligand binding to a particular receptor, investigate receptor localization in different organs or regions using autoradiography, categorize receptor subtypes, and probe mechanisms of receptor signaling, via measurements of agonist binding and its regulation by ions, nucleotides, and other allosteric modulators. This unit reviews the theory of receptor binding and explains how to analyze experimental data. Since binding data are usually best analyzed using nonlinear regression, this unit also explains the principles of curve fitting with nonlinear regression.

  14. 49 CFR 236.728 - Circuit, trap.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Circuit, trap. 236.728 Section 236.728... Circuit, trap. A term applied to a circuit used where it is desirable to provide a track circuit but where it is impracticable to maintain a track circuit....

  15. Variational integrators for electric circuits

    CERN Document Server

    Ober-Blöbaum, Sina; Cheng, Mulin; Owhadi, Houman; Marsden, Jerrold E

    2011-01-01

    In this contribution, we develop a variational integrator for the simulation of (stochastic and multiscale) electric circuits. When considering the dynamics of an electrical circuit, one is faced with three special situations: 1. The system involves external (control) forcing through external (controlled) voltage sources and resistors. 2. The system is constrained via the Kirchhoff current (KCL) and voltage laws (KVL). 3. The Lagrangian is degenerate. Based on a geometric setting, an appropriate variational formulation is presented to model the circuit from which the equations of motion are derived. A time-discrete variational formulation provides an iteration scheme for the simulation of the electric circuit. Dependent on the discretization, the intrinsic degeneracy of the system can be canceled for the discrete variational scheme. In this way, a variational integrator is constructed that gains several advantages compared to standard integration tools for circuits; in particular, a comparison to BDF methods ...

  16. Electronic design with integrated circuits

    Science.gov (United States)

    Comer, D. J.

    The book is concerned with the application of integrated circuits and presents the material actually needed by the system designer to do an effective job. The operational amplifier (op amp) is discussed, taking into account the electronic amplifier, the basic op amp, the practical op amp, analog applications, and digital applications. Digital components are considered along with combinational logic, digital subsystems, the microprocessor, special circuits, communications, and integrated circuit building blocks. Attention is given to logic gates, logic families, multivibrators, the digital computer, digital methods, communicating with a computer, computer organization, register and timing circuits for data transfer, arithmetic circuits, memories, the microprocessor chip, the control unit, communicating with the microprocessor, examples of microprocessor architecture, programming a microprocessor, the voltage-controlled oscillator, the phase-locked loop, analog-to-digital conversion, amplitude modulation, frequency modulation, pulse and digital transmission, the semiconductor diode, the bipolar transistor, and the field-effect transistor.

  17. Demultiplexer circuit for neural stimulation

    Science.gov (United States)

    Wessendorf, Kurt O; Okandan, Murat; Pearson, Sean

    2012-10-09

    A demultiplexer circuit is disclosed which can be used with a conventional neural stimulator to extend the number of electrodes which can be activated. The demultiplexer circuit, which is formed on a semiconductor substrate containing a power supply that provides all the dc electrical power for operation of the circuit, includes digital latches that receive and store addressing information from the neural stimulator one bit at a time. This addressing information is used to program one or more 1:2.sup.N demultiplexers in the demultiplexer circuit which then route neural stimulation signals from the neural stimulator to an electrode array which is connected to the outputs of the 1:2.sup.N demultiplexer. The demultiplexer circuit allows the number of individual electrodes in the electrode array to be increased by a factor of 2.sup.N with N generally being in a range of 2-4.

  18. Analyzing Workforce Education. Monograph.

    Science.gov (United States)

    Texas Community & Technical Coll. Workforce Education Consortium.

    This monograph examines the issue of task analysis as used in workplace literacy programs, debating the need for it and how to perform it in a rapidly changing environment. Based on experiences of community colleges in Texas, the report analyzes ways that task analysis can be done and how to implement work force education programs more quickly.…

  19. List mode multichannel analyzer

    Science.gov (United States)

    Archer, Daniel E.; Luke, S. John; Mauger, G. Joseph; Riot, Vincent J.; Knapp, David A.

    2007-08-07

    A digital list mode multichannel analyzer (MCA) built around a programmable FPGA device for onboard data analysis and on-the-fly modification of system detection/operating parameters, and capable of collecting and processing data in very small time bins (<1 millisecond) when used in histogramming mode, or in list mode as a list mode MCA.

  20. Centrifugal analyzer development

    International Nuclear Information System (INIS)

    The development of the centrifuge fast analyzer (CFA) is reviewed. The development of a miniature CFA with computer data analysis is reported and applications for automated diagnostic chemical and hematological assays are discussed. A portable CFA system with microprocessor was adapted for field assays of air and water samples for environmental pollutants, including ammonia, nitrates, nitrites, phosphates, sulfates, and silica. 83 references

  1. Analyzing business models

    DEFF Research Database (Denmark)

    Nielsen, Christian

    2014-01-01

    , because the costs of processing and analyzing it exceed the benefits indicating bounded rationality. Hutton (2002) concludes that the analyst community’s inability to raise important questions on quality of management and the viability of its business model inevitably led to the Enron debacle. There seems...

  2. Thermally-induced voltage alteration for integrated circuit analysis

    Energy Technology Data Exchange (ETDEWEB)

    Cole, Jr., Edward I. (Albuquerque, NM)

    2000-01-01

    A thermally-induced voltage alteration (TIVA) apparatus and method are disclosed for analyzing an integrated circuit (IC) either from a device side of the IC or through the IC substrate to locate any open-circuit or short-circuit defects therein. The TIVA apparatus uses constant-current biasing of the IC while scanning a focused laser beam over electrical conductors (i.e. a patterned metallization) in the IC to produce localized heating of the conductors. This localized heating produces a thermoelectric potential due to the Seebeck effect in any conductors with open-circuit defects and a resistance change in any conductors with short-circuit defects, both of which alter the power demand by the IC and thereby change the voltage of a source or power supply providing the constant-current biasing. By measuring the change in the supply voltage and the position of the focused and scanned laser beam over time, any open-circuit or short-circuit defects in the IC can be located and imaged. The TIVA apparatus can be formed in part from a scanning optical microscope, and has applications for qualification testing or failure analysis of ICs.

  3. Thermally-induced voltage alteration for integrated circuit analysis

    Energy Technology Data Exchange (ETDEWEB)

    Cole, E.I. Jr.

    2000-06-20

    A thermally-induced voltage alteration (TIVA) apparatus and method are disclosed for analyzing an integrated circuit (IC) either from a device side of the IC or through the IC substrate to locate any open-circuit or short-circuit defects therein. The TIVA apparatus uses constant-current biasing of the IC while scanning a focused laser beam over electrical conductors (i.e. a patterned metallization) in the IC to produce localized heating of the conductors. This localized heating produces a thermoelectric potential due to the Seebeck effect in any conductors with open-circuit defects and a resistance change in any conductors with short-circuit defects, both of which alter the power demand by the IC and thereby change the voltage of a source or power supply providing the constant-current biasing. By measuring the change in the supply voltage and the position of the focused and scanned laser beam over time, any open-circuit or short-circuit defects in the IC can be located and imaged. The TIVA apparatus can be formed in part from a scanning optical microscope, and has applications for qualification testing or failure analysis of ICs.

  4. Performance analysis of electrical circuits /PANE/

    Science.gov (United States)

    Johnson, K. L.; Steinberg, L. L.

    1968-01-01

    Automated statistical and worst case computer program has been designed to perform dc and ac steady circuit analyses. The program determines the worst case circuit performance by solving circuit equations.

  5. 30 CFR 75.800 - High-voltage circuits; circuit breakers.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false High-voltage circuits; circuit breakers. 75.800... § 75.800 High-voltage circuits; circuit breakers. High-voltage circuits entering the underground area of any coal mine shall be protected by suitable circuit breakers of adequate interrupting...

  6. Lear CAN analyzer

    OpenAIRE

    Peiró Ibañez, Felipe

    2013-01-01

    Since it was introduced in the automotive industry, the protocol CAN (Controller Area Network) has been widely used for its benefits. This has led many companies to offer several hardware and software solutions in order to monitor the communications that gives this protocol. The current master thesis presents the Lear CAN Analyzer as a software tool developed within the company LEAR Corporation. It is designed to be used in the automobile industry as a complement or substitute for other co...

  7. Analyzing business process management

    OpenAIRE

    Skjæveland, Børge

    2013-01-01

    Within the Oil & Gas Industry, the market is constantly growing more competitive, forcing companies to continually adapt to changes. Companies need to cut costs and improve the business efficiency. One way of successfully managing these challenges is to implement business process management in the organization. This thesis will analyze how Oceaneering Asset Integrity AS handled the implementation of a Business Process Management System and the effects it had on the employees. The main goal...

  8. Radioisotope analyzer of barium

    International Nuclear Information System (INIS)

    Principle of operation and construction of radioisotope barium sulphate analyzer type MZB-2 for fast determination of barium sulphate content in barite ores and enrichment products are described. The gauge equipped with Am-241 and a scintillation detector enables measurement of barium sulphate content in prepared samples of barite ores in the range 60% - 100% with the accuracy of 1%. The gauge is used in laboratories of barite mine and ore processing plant. 2 refs., 2 figs., 1 tab. (author)

  9. Interpolation circuit with high resolution and high response speed

    Science.gov (United States)

    Piao, Weiying; Yuan, Yibao; Xu, Lianhu; Zhang, Hao

    2009-05-01

    An interpolation circuit based upon the looking-up table by hardware is presented. Output data of two A/D convertors are connected to ROM's address bus. The memory space of ROM is divided. When the address bus is activated by A/D conversion's output data, the ROM's output data is interpolation data. This circuit has high response speed, and it is easy to obtain high interpolation multiple. The same kind of hardware circuit can achieve different interpolation multiple by modifying ROM's data. It is very convenient and flexible. The principle of direction judgment and counting is analyzed; the implementation speed and maximal interpolation multiple are discussed in this paper. Finally through experiment, make sure this circuit not only has the characteristic of high response speed and high interpolation multiple, but also avoids the counting error of micro-computer interpolation.

  10. A novel circuit architecture for fourth subharmonie mixers

    Institute of Scientific and Technical Information of China (English)

    Yao Changfei; Xu Conghai; Zhou Ming; Luo Yunsheng

    2012-01-01

    A circuit topology for high-order subharmonic (SH) mixers is described.By phase cancellation of idle frequency components,the SH mixer circuit can eliminate the complicated design procedure of idle frequency circuits.Similarly,the SH mixer circuit can achieve a high port isolation by phase cancellation of the leakage LO,RF and idle frequency signals.Based on the high-order SH mixer architecture,a new Ka-band fourth SH mixer is analyzed and designed,it shows the lowest measured conversion loss of 8.3 dB at 38.4 GHz and the loss is lower than 10.3 dB in 34-39 GHz.Measured LO-IF,RF-LO,RF-IF port isolation are better than 30.7 dB,22.9dB and 46.5 dB,respectively.

  11. IPv6 Protocol Analyzer

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    With the emerging of next generation Intemet protocol (IPv6), it is expected to replace the current version of Internet protocol (IPv4) that will be exhausted in the near future. Besides providing adequate address space, some other new features are included into the new 128 bits of IP such as IP auto configuration, quality of service, simple routing capability, security, mobility and multicasting. The current protocol analyzer will not be able to handle IPv6 packets. This paper will focus on developing protocol analyzer that decodes IPv6 packet. IPv6 protocol analyzer is an application module,which is able to decode the IPv6 packet and provide detail breakdown of the construction of the packet. It has to understand the detail construction of the IPv6, and provide a high level abstraction of bits and bytes of the IPv6 packet.Thus it increases network administrators' understanding of a network protocol,helps he/she in solving protocol related problem in a IPv6 network environment.

  12. Global optimization of digital circuits

    Science.gov (United States)

    Flandera, Richard

    1991-12-01

    This thesis was divided into two tasks. The first task involved developing a parser which could translate a behavioral specification in Very High-Speed Integrated Circuits (VHSIC) Hardware Description Language (VHDL) into the format used by an existing digital circuit optimization tool, Boolean Reasoning In Scheme (BORIS). Since this tool is written in Scheme, a dialect of Lisp, the parser was also written in Scheme. The parser was implemented is Artez's modification of Earley's Algorithm. Additionally, a VHDL tokenizer was implemented in Scheme and a portion of the VHDL grammar was converted into the format which the parser uses. The second task was the incorporation of intermediate functions into BORIS. The existing BORIS contains a recursive optimization system that optimizes digital circuits by using circuit outputs as inputs into other circuits. Intermediate functions provide a greater selection of functions to be used as circuits inputs. Using both intermediate functions and output functions, the costs of the circuits in the test set were reduced by 43 percent. This is a 10 percent reduction when compared to the existing recursive optimization system. Incorporating intermediate functions into BORIS required the development of an intermediate-function generator and a set of control methods to keep the computation time from increasing exponentially.

  13. Spectral Purity Enhancement via Polyphase Multipath Circuits

    OpenAIRE

    Mensink, Eisse; Klumperink, Eric; Nauta, Bram

    2004-01-01

    The central question of this paper is: can we enhance the spectral purity of nonlinear circuits by using polyphase multipath circuits? The basic idea behind polyphase multipath circuits is to split the nonlinear circuits into two or more paths and exploit phase differences between these paths to cancel undesired distortion products. It turns out that it is very well possible to use polyphase multipath circuits to cancel distortion products produced by a nonlinear circuit. Unfortunately, there...

  14. Measurements of the Effects of Smoke on Active Circuits

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, T.J.

    1999-02-09

    Smoke has long been recognized as the most common source of fire damage to electrical equipment; however, most failures have been analyzed after the fire was out and the smoke vented. The effects caused while the smoke is still in the air have not been explored. Such effects have implications for new digital equipment being installed in nuclear reactors. The U.S. Nuclear Regulatory Commission is sponsoring work to determine the impact of smoke on digital instrumentation and control. As part of this program, Sandia National Laboratories has tested simple active circuits to determine how smoke affects them. These tests included the study of three possible failure modes on a functional board: (1) circuit bridging, (2) corrosion (metal loss), and (3) induction of stray capacitance. The performance of nine different circuits was measured continuously on bare and conformably coated boards during smoke exposures lasting 1 hour each and continued for 24 hours after the exposure started. The circuit that was most affected by smoke (100% change in measured values) was the one most sensitive to circuit bridging. Its high impedance (50 M{Omega}) was shorted during the exposure, but in some cases recovered after the smoke was vented. The other two failure modes, corrosion and induced stray capacitance, caused little change in the function of the circuits. The smoke permanently increased resistance of the circuit tested for corrosion, implying that the cent acts were corroded. However, the change was very small (< 2%). The stray-capacitance test circuit showed very little change after a smoke exposure in either the short or long term. The results of the tests suggest that conformal coatings and type of circuit are major considerations when designing digital circuitry to be used in critical control systems.

  15. Measurements of the effects of smoke on active circuits

    International Nuclear Information System (INIS)

    Smoke has long been recognized as the most common source of fire damage to electrical equipment; however, most failures have been analyzed after the fire was out and the smoke vented. The effects caused while the smoke is still in the air have not been explored. Such effects have implications for new digital equipment being installed in nuclear reactors. The US Nuclear Regulatory Commission is sponsoring work to determine the impact of smoke on digital instrumentation and control. As part of this program, Sandia National Laboratories has tested simple active circuits to determine how smoke affects them. These tests included the study of three possible failure modes on a functional board: (1) circuit bridging, (2) corrosion (metal loss), and (3) induction of stray capacitance. The performance of nine different circuits was measured continuously on bare and conformally coated boards during smoke exposures lasting 1 hour each and continued for 24 hours after the exposure started. The circuit that was most affected by smoke (100% change in measured values) was the one most sensitive to circuit bridging. Its high impedance (50 Mohm) was shorted during the exposure, but in some cases recovered after the smoke was vented. The other two failure modes, corrosion and induced stray capacitance, caused little change in the function of the circuits. The smoke permanently increased resistance of the circuit tested for corrosion, implying that the contacts were corroded. However, the change was very small (< 2%). The stray capacitance test circuit showed very little change after a smoke exposure in either the short or long term. The results of the tests suggest that conformal coatings and type of circuit are major considerations when designing digital circuitry to be used in critical control systems

  16. Note: A calibration method to determine the lumped-circuit parameters of a magnetic probe

    Science.gov (United States)

    Li, Fuming; Chen, Zhipeng; Zhu, Lizhi; Liu, Hai; Wang, Zhijiang; Zhuang, Ge

    2016-06-01

    This paper describes a novel method to determine the lumped-circuit parameters of a magnetic inductive probe for calibration by using Helmholtz coils with high frequency power supply (frequency range: 10 kHz-400 kHz). The whole calibration circuit system can be separated into two parts: "generator" circuit and "receiver" circuit. By implementing the Fourier transform, two analytical lumped-circuit models, with respect to these separated circuits, are constructed to obtain the transfer function between each other. Herein, the precise lumped-circuit parameters (including the resistance, inductance, and capacitance) of the magnetic probe can be determined by fitting the experimental data to the transfer function. Regarding the fitting results, the finite impedance of magnetic probe can be used to analyze the transmission of a high-frequency signal between magnetic probes, cables, and acquisition system.

  17. Determining Covers in Combinational Circuits

    Directory of Open Access Journals (Sweden)

    Ljubomir Cvetkovic

    2011-05-01

    Full Text Available In this paper we propose a procedure for determining 0- or 1-cover of an arbitrary line in a combinational circuit. When determining a cover we do not need Boolean expression for the line; only the circuit structure is used. Within the proposed procedure we use the tools of the cube theory, in particular, some operations defined on cubes. The procedure can be applied for determining 0- and 1- covers of output lines in programmable logic devices. Basically, this procedure is a method for the analysis of a combinational circuit.

  18. The Maplin electronic circuits handbook

    CERN Document Server

    Tooley, Michael

    2015-01-01

    The Maplin Electronic Circuits Handbook provides pertinent data, formula, explanation, practical guidance, theory and practical guidance in the design, testing, and construction of electronic circuits. This book discusses the developments in electronics technology techniques.Organized into 11 chapters, this book begins with an overview of the common types of passive component. This text then provides the reader with sufficient information to make a correct selection of passive components for use in the circuits. Other chapters consider the various types of the most commonly used semiconductor

  19. Secure integrated circuits and systems

    CERN Document Server

    Verbauwhede, Ingrid MR

    2010-01-01

    On any advanced integrated circuit or 'system-on-chip' there is a need for security. In many applications the actual implementation has become the weakest link in security rather than the algorithms or protocols. The purpose of the book is to give the integrated circuits and systems designer an insight into the basics of security and cryptography from the implementation point of view. As a designer of integrated circuits and systems it is important to know both the state-of-the-art attacks as well as the countermeasures. Optimizing for security is different from optimizations for speed, area,

  20. Fluorescence analyzer for lignin

    Science.gov (United States)

    Berthold, John W.; Malito, Michael L.; Jeffers, Larry

    1993-01-01

    A method and apparatus for measuring lignin concentration in a sample of wood pulp or black liquor comprises a light emitting arrangement for emitting an excitation light through optical fiber bundles into a probe which has an undiluted sensing end facing the sample. The excitation light causes the lignin concentration to produce fluorescent emission light which is then conveyed through the probe to analyzing equipment which measures the intensity of the emission light. Measures a This invention was made with Government support under Contract Number DOE: DE-FC05-90CE40905 awarded by the Department of Energy (DOE). The Government has certain rights in this invention.

  1. Analyzing Chinese Financial Reporting

    Institute of Scientific and Technical Information of China (English)

    SABRINA; ZHANG

    2008-01-01

    If the world’s capital markets could use a harmonized accounting framework it would not be necessary for a comparison between two or more sets of accounting standards. However,there is much to do before this becomes reality.This article aims to pres- ent a general overview of China’s General Accepted Accounting Principles(GAAP), U.S.General Accepted Accounting Principles and International Financial Reporting Standards(IFRS),and to analyze the differ- ences among IFRS,U.S.GAAP and China GAAP using fixed assets as an example.

  2. Experimental study of natural circulation circuit

    Energy Technology Data Exchange (ETDEWEB)

    Lemos, Wanderley F.; Su, Jian, E-mail: wlemos@lasme.coppe.ufrj.br, E-mail: sujian@lasme.coppe.ufrj.br [Coordenacao dos Programas de Pos-Graduacao de Engenharia (LASME/COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Lab. de Simulacao e Metodos Numericos; Faccini, Jose L.H., E-mail: faccini@ien.gov.br [Instituto de Engenharia Nuclear (LTE/IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil). Lab. de Termo-Hidraulica Experimental

    2011-07-01

    This work presents an experimental study about fluid flows behavior in natural circulation, under conditions of single-phase flow. The experiment was performed through experimental thermal-hydraulic circuit built at IEN. This test equipment has performance similar to passive system of residual heat removal present in Advanced Pressurized Water Reactors (APWR). This experimental study aims to observing and analyzing the natural circulation phenomenon, using this experimental circuit that was dimensioned and built based on concepts of similarity and scale. This philosophy allows the analysis of natural circulation behavior in single-phase flow conditions proportionally to the functioning real conditions of a nuclear reactor. The experiment was performed through procedures to initialization of hydraulic feeding of primary and secondary circuits and electrical energizing of resistors installed inside heater. Power controller has availability to adjust values of electrical power to feeding resistors, in order to portray several conditions of energy decay of nuclear reactor in a steady state. Data acquisition system allows the measurement and monitoring of the evolution of the temperature in various points through thermocouples installed in strategic points along hydraulic circuit. The behavior of the natural circulation phenomenon was monitored by graphical interface on computer screen, showing the temperature evolutions of measuring points and results stored in digital spreadsheets. The results stored in digital spreadsheets allowed the getting of data to graphic construction and discussion about natural circulation phenomenon. Finally, the calculus of Reynolds number allowed the establishment for a correlation of friction in function of geometric scales of length, heights and cross section of tubing, considering a natural circulation flow throughout in the region of hot leg. (author)

  3. Ring Image Analyzer

    Science.gov (United States)

    Strekalov, Dmitry V.

    2012-01-01

    Ring Image Analyzer software analyzes images to recognize elliptical patterns. It determines the ellipse parameters (axes ratio, centroid coordinate, tilt angle). The program attempts to recognize elliptical fringes (e.g., Newton Rings) on a photograph and determine their centroid position, the short-to-long-axis ratio, and the angle of rotation of the long axis relative to the horizontal direction on the photograph. These capabilities are important in interferometric imaging and control of surfaces. In particular, this program has been developed and applied for determining the rim shape of precision-machined optical whispering gallery mode resonators. The program relies on a unique image recognition algorithm aimed at recognizing elliptical shapes, but can be easily adapted to other geometric shapes. It is robust against non-elliptical details of the image and against noise. Interferometric analysis of precision-machined surfaces remains an important technological instrument in hardware development and quality analysis. This software automates and increases the accuracy of this technique. The software has been developed for the needs of an R&TD-funded project and has become an important asset for the future research proposal to NASA as well as other agencies.

  4. Field Deployable DNA analyzer

    Energy Technology Data Exchange (ETDEWEB)

    Wheeler, E; Christian, A; Marion, J; Sorensen, K; Arroyo, E; Vrankovich, G; Hara, C; Nguyen, C

    2005-02-09

    This report details the feasibility of a field deployable DNA analyzer. Steps for swabbing cells from surfaces and extracting DNA in an automatable way are presented. Since enzymatic amplification reactions are highly sensitive to environmental contamination, sample preparation is a crucial step to make an autonomous deployable instrument. We perform sample clean up and concentration in a flow through packed bed. For small initial samples, whole genome amplification is performed in the packed bed resulting in enough product for subsequent PCR amplification. In addition to DNA, which can be used to identify a subject, protein is also left behind, the analysis of which can be used to determine exposure to certain substances, such as radionuclides. Our preparative step for DNA analysis left behind the protein complement as a waste stream; we determined to learn if the proteins themselves could be analyzed in a fieldable device. We successfully developed a two-step lateral flow assay for protein analysis and demonstrate a proof of principle assay.

  5. One high-efficiency analysis method for high-speed circuit networks containing distributed parameter elements

    Institute of Scientific and Technical Information of China (English)

    Lei DOU; Zhiquan WANG

    2005-01-01

    In the field of high-speed circuits,the analysis of mixed circuit networks containing both distributed parameter elements and lumped parameter elements becomes ever important.This paper presents a new method for analyzing mixed circuit networks.It adds transmission line end currents to the circuit variables of the classical modified nodal approach and can be applied directly to the mixed circuit networks.We also introduce a frequency-domain technique without requiring decoupling for multiconductor transmission lines.The two methods are combined together to efficiently analyze high-speed circuit networks containing uniform,nonuniform,and frequency-dependent transmission lines.Numerical experiment is presented and the results are compared with that computed by PSPICE.

  6. Composite behaviors of dual meminductor circuits

    Institute of Scientific and Technical Information of China (English)

    郑辞晏; 于东升; 梁燕; 陈孟科

    2015-01-01

    This paper focuses on analyzing the composite dynamic behaviors of two meminductors in serial and parallel connec-tions with different polarities. Based on the constitutive relations, two time-integral-of-flux (TIF) controlled meminductors are adopted to theoretically demonstrate the variation of memductance in terms of TIF, charge, flux, and current. By uti-lizing a floating memristor-less meminductor emulator, the theoretical analysis reported in this paper is confirmed via a PSPICE simulation study and hardware experiment. Good agreement among theoretical analysis, simulation, and hardware validation confirms that dual meminductor circuits in composite connections behave as a new meminductor with higher complexity.

  7. Discharge quenching circuit for counters

    International Nuclear Information System (INIS)

    A circuit for quenching discharges in gas-discharge detectors with working voltage of 3-5 kV based on transistors operating in the avalanche mode is described. The quenching circuit consists of a coordinating emitter follower, amplifier-shaper for avalanche key cascade control which changes potential on the counter electrodes and a shaper of discharge quenching duration. The emitter follower is assembled according to a widely used flowsheet with two transistors. The circuit permits to obtain a rectangular quenching pulse with front of 100 ns and an amplitude of up to 3.2 kV at duration of 500 μm-8 ms. Application of the quenching circuit described permits to obtain countering characteristics with the slope less than or equal to 0.02%/V and plateau extent greater than or equal to 300 V

  8. Wireless communications circuits and systems

    CERN Document Server

    Sun, Yichuang

    2004-01-01

    This new book examines integrated circuits, systems and transceivers for wireless and mobile communications. It covers the most recent developments in key RF, IF, analogue, mixed-signal components and single-chip transceivers in CMOS technology.

  9. Extensional Uniformity for Boolean Circuits

    CERN Document Server

    McKenzie, Pierre; Vollmer, Heribert

    2008-01-01

    Imposing an extensional uniformity condition on a non-uniform circuit complexity class C means simply intersecting C with a uniform class L. By contrast, the usual intensional uniformity conditions require that a resource-bounded machine be able to exhibit the circuits in the circuit family defining C. We say that (C,L) has the "Uniformity Duality Property" if the extensionally uniform class C \\cap L can be captured intensionally by means of adding so-called "L-numerical predicates" to the first-order descriptive complexity apparatus describing the connection language of the circuit family defining C. This paper exhibits positive instances and negative instances of the Uniformity Duality Property.

  10. Circuit design on plastic foils

    CERN Document Server

    Raiteri, Daniele; Roermund, Arthur H M

    2015-01-01

    This book illustrates a variety of circuit designs on plastic foils and provides all the information needed to undertake successful designs in large-area electronics.  The authors demonstrate architectural, circuit, layout, and device solutions and explain the reasons and the creative process behind each. Readers will learn how to keep under control large-area technologies and achieve robust, reliable circuit designs that can face the challenges imposed by low-cost low-temperature high-throughput manufacturing.   • Discusses implications of problems associated with large-area electronics and compares them to standard silicon; • Provides the basis for understanding physics and modeling of disordered material; • Includes guidelines to quickly setup the basic CAD tools enabling efficient and reliable designs; • Illustrates practical solutions to cope with hard/soft faults, variability, mismatch, aging and bias stress at architecture, circuit, layout, and device levels.

  11. Practical circuits with Physarum Wires

    OpenAIRE

    Whiting, James G. H.; Mayne, Richard; Moody, Nadine; Costello, Ben de Lacy; Adamatzky, Andrew

    2015-01-01

    Purpose: Protoplasmic tubes of Physarum polycephalum, also know as Physarum Wires (PW), have been previously suggested as novel bio- electronic components. Until recently, practical examples of electronic circuits using PWs have been limited. These PWs have been shown to be self repairing, offering significant advantage over traditional electronic components. This article documents work performed to produce practical circuits using PWs. Method: We have demonstrated through manufacture and tes...

  12. Residual gas analyzer calibration

    Science.gov (United States)

    Lilienkamp, R. H.

    1972-01-01

    A technique which employs known gas mixtures to calibrate the residual gas analyzer (RGA) is described. The mass spectra from the RGA are recorded for each gas mixture. This mass spectra data and the mixture composition data each form a matrix. From the two matrices the calibration matrix may be computed. The matrix mathematics requires the number of calibration gas mixtures be equal to or greater than the number of gases included in the calibration. This technique was evaluated using a mathematical model of an RGA to generate the mass spectra. This model included shot noise errors in the mass spectra. Errors in the gas concentrations were also included in the valuation. The effects of these errors was studied by varying their magnitudes and comparing the resulting calibrations. Several methods of evaluating an actual calibration are presented. The effects of the number of gases in then, the composition of the calibration mixture, and the number of mixtures used are discussed.

  13. Analyzing architecture articles

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    In the present study, we express the quality, function, and characteristics of architecture to help people comprehensively understand what architecture is. We also reveal the problems and conflict found in population, land, water resources, pollution, energy, and the organization systems in construction. China’s economy is transforming. We should focus on the cities, architectural environment, energy conservation, emission-reduction, and low-carbon output that will result in successful green development. We should macroscopically and microscopically analyze the development, from the natural environment to the artificial environment; from the relationship between human beings and nature to the combination of social ecology in cities, and farmlands. We must learn to develop and control them harmoniously and scientifically to provide a foundation for the methods used in architecture research.

  14. PDA: Pooled DNA analyzer

    Directory of Open Access Journals (Sweden)

    Lin Chin-Yu

    2006-04-01

    Full Text Available Abstract Background Association mapping using abundant single nucleotide polymorphisms is a powerful tool for identifying disease susceptibility genes for complex traits and exploring possible genetic diversity. Genotyping large numbers of SNPs individually is performed routinely but is cost prohibitive for large-scale genetic studies. DNA pooling is a reliable and cost-saving alternative genotyping method. However, no software has been developed for complete pooled-DNA analyses, including data standardization, allele frequency estimation, and single/multipoint DNA pooling association tests. This motivated the development of the software, 'PDA' (Pooled DNA Analyzer, to analyze pooled DNA data. Results We develop the software, PDA, for the analysis of pooled-DNA data. PDA is originally implemented with the MATLAB® language, but it can also be executed on a Windows system without installing the MATLAB®. PDA provides estimates of the coefficient of preferential amplification and allele frequency. PDA considers an extended single-point association test, which can compare allele frequencies between two DNA pools constructed under different experimental conditions. Moreover, PDA also provides novel chromosome-wide multipoint association tests based on p-value combinations and a sliding-window concept. This new multipoint testing procedure overcomes a computational bottleneck of conventional haplotype-oriented multipoint methods in DNA pooling analyses and can handle data sets having a large pool size and/or large numbers of polymorphic markers. All of the PDA functions are illustrated in the four bona fide examples. Conclusion PDA is simple to operate and does not require that users have a strong statistical background. The software is available at http://www.ibms.sinica.edu.tw/%7Ecsjfann/first%20flow/pda.htm.

  15. Study on the instantaneous protection reliability of low voltage circuit breakers

    Institute of Scientific and Technical Information of China (English)

    LU Jian-guo; DU Tai-hang; LUO Yan-yan

    2007-01-01

    This paper outlines the significance of enhancing the instantaneous protection reliability of low voltage circuit breakers and describes their main failure modes. The instantaneous failure mechanism of low voltage circuit breakers was analyzed so that measures to improve instantaneous protection reliability can be determined. Furthermore, the theory of the instantaneous characteristics Calibration device for low voltage circuit breakers and the method of eliminating the non-periodic component of test current are given in detail. Finally, the test results are presented.

  16. Integrated Power Flow and Short Circuit Calculation Method for Distribution Network with Inverter Based Distributed Generation

    OpenAIRE

    Shan Yang; Xiangqian Tong

    2016-01-01

    Power flow calculation and short circuit calculation are the basis of theoretical research for distribution network with inverter based distributed generation. The similarity of equivalent model for inverter based distributed generation during normal and fault conditions of distribution network and the differences between power flow and short circuit calculation are analyzed in this paper. Then an integrated power flow and short circuit calculation method for distribution network with inverte...

  17. Pseudostupidity and analyzability.

    Science.gov (United States)

    Cohn, L S

    1989-01-01

    This paper seeks to heighten awareness of pseudostupidity and the potential analyzability of patients who manifest it by defining and explicating it, reviewing the literature, and presenting in detail the psychoanalytic treatment of a pseudostupid patient. Pseudostupidity is caused by an inhibition of the integration and synthesis of thoughts resulting in a discrepancy between intellectual capacity and apparent intellect. The patient's pseudostupidity was determined in part by his need to prevent his being more successful than father, i.e., defeating his oedipal rival. Knowing and learning were instinctualized. The patient libidinally and defensively identified with father's passive, masochistic position. He needed to frustrate the analyst as he had felt excited and frustrated by his parents' nudity and thwarted by his inhibitions. He wanted to cause the analyst to feel as helpless as he, the patient, felt. Countertransference frustration was relevant and clinically useful in the analysis. Interpretation of evolving relevant issues led to more anxiety and guilt, less pseudostupidity, a heightened alliance, and eventual working through. Negative therapeutic reactions followed the resolution of pseudostupidity. PMID:2708771

  18. Downhole Fluid Analyzer Development

    Energy Technology Data Exchange (ETDEWEB)

    Bill Turner

    2006-11-28

    A novel fiber optic downhole fluid analyzer has been developed for operation in production wells. This device will allow real-time determination of the oil, gas and water fractions of fluids from different zones in a multizone or multilateral completion environment. The device uses near infrared spectroscopy and induced fluorescence measurement to unambiguously determine the oil, water and gas concentrations at all but the highest water cuts. The only downhole components of the system are the fiber optic cable and windows. All of the active components--light sources, sensors, detection electronics and software--will be located at the surface, and will be able to operate multiple downhole probes. Laboratory testing has demonstrated that the sensor can accurately determine oil, water and gas fractions with a less than 5 percent standard error. Once installed in an intelligent completion, this sensor will give the operating company timely information about the fluids arising from various zones or multilaterals in a complex completion pattern, allowing informed decisions to be made on controlling production. The research and development tasks are discussed along with a market analysis.

  19. Analyzing Spacecraft Telecommunication Systems

    Science.gov (United States)

    Kordon, Mark; Hanks, David; Gladden, Roy; Wood, Eric

    2004-01-01

    Multi-Mission Telecom Analysis Tool (MMTAT) is a C-language computer program for analyzing proposed spacecraft telecommunication systems. MMTAT utilizes parameterized input and computational models that can be run on standard desktop computers to perform fast and accurate analyses of telecommunication links. MMTAT is easy to use and can easily be integrated with other software applications and run as part of almost any computational simulation. It is distributed as either a stand-alone application program with a graphical user interface or a linkable library with a well-defined set of application programming interface (API) calls. As a stand-alone program, MMTAT provides both textual and graphical output. The graphs make it possible to understand, quickly and easily, how telecommunication performance varies with variations in input parameters. A delimited text file that can be read by any spreadsheet program is generated at the end of each run. The API in the linkable-library form of MMTAT enables the user to control simulation software and to change parameters during a simulation run. Results can be retrieved either at the end of a run or by use of a function call at any time step.

  20. Piezogenerator impedance matching using Mason equivalent circuit for harvester identification

    Science.gov (United States)

    Li, Yang; Richard, Claude

    2014-04-01

    Any piezoelectric generator structure can be modeled close to its resonance by an equivalent circuit derived from the well known Mason equivalent circuit. This equivalent circuit can therefore be used in order to optimize the harvested power using usual electrical impedance matching. The objective of this paper is to illustrate the full process leading to the definition of the proper passive load allowing the optimization of the harvested energy of any harvesting device. First, the electric equivalent circuit of the generator is derived from the Mason equivalent circuit of a seismic harvester. Theoretical ideal impedance matching and optimal load analyze is then given emphasizing the fact that for a given acceleration a constant optimal output power is achievable for any frequency as long as the optimal load is feasible. Identification of the equivalent circuit of an experimental seismic harvester is then derived and matched impedance is defined both theoretically and experimentally. Results demonstrate that an optimal load can always be obtained and that the corresponding output power is constant. However, it is very sensitive to this impedance, and that even if impedance matching is a longtime well known technique, it is not really experimentally and practically achievable.

  1. Difference-Equation/Flow-Graph Circuit Analysis

    Science.gov (United States)

    Mcvey, I. M.

    1988-01-01

    Numerical technique enables rapid, approximate analyses of electronic circuits containing linear and nonlinear elements. Practiced in variety of computer languages on large and small computers; for circuits simple enough, programmable hand calculators used. Although some combinations of circuit elements make numerical solutions diverge, enables quick identification of divergence and correction of circuit models to make solutions converge.

  2. Multi-Layer E-Textile Circuits

    Science.gov (United States)

    Dunne, Lucy E.; Bibeau, Kaila; Mulligan, Lucie; Frith, Ashton; Simon, Cory

    2012-01-01

    Stitched e-textile circuits facilitate wearable, flexible, comfortable wearable technology. However, while stitched methods of e-textile circuits are common, multi-layer circuit creation remains a challenge. Here, we present methods of stitched multi-layer circuit creation using accessible tools and techniques.

  3. Tunable circuit for tunable capacitor devices

    Science.gov (United States)

    Rivkina, Tatiana; Ginley, David S.

    2006-09-19

    A tunable circuit (10) for a capacitively tunable capacitor device (12) is provided. The tunable circuit (10) comprises a tunable circuit element (14) and a non-tunable dielectric element (16) coupled to the tunable circuit element (16). A tunable capacitor device (12) and a method for increasing the figure of merit in a tunable capacitor device (12) are also provided.

  4. Comparison between four piezoelectric energy harvesting circuits

    Institute of Scientific and Technical Information of China (English)

    Jinhao QIU; Hao JIANG; Hongli JI; Kongjun ZHU

    2009-01-01

    This paper investigates and compares the efficiencies of four different interfaces for vibration-based energy harvesting systems. Among those four circuits, two circuits adopt the synchronous switching technique, in which the circuit is switched synchronously with the vibration. In this study, a simple source-less trigger circuit used to control the synchronized switch is proposed and two interface circuits of energy harvesting systems are designed based on the trigger circuit. To validate the effectiveness of the proposed circuits, an experimental system was established and the power harvested by those circuits from a vibration beam was measured. Experimental results show that the two new circuits can increase the harvested power by factors 2.6 and 7, respectively, without consuming extra power in the circuits.

  5. Crew Activity Analyzer

    Science.gov (United States)

    Murray, James; Kirillov, Alexander

    2008-01-01

    The crew activity analyzer (CAA) is a system of electronic hardware and software for automatically identifying patterns of group activity among crew members working together in an office, cockpit, workshop, laboratory, or other enclosed space. The CAA synchronously records multiple streams of data from digital video cameras, wireless microphones, and position sensors, then plays back and processes the data to identify activity patterns specified by human analysts. The processing greatly reduces the amount of time that the analysts must spend in examining large amounts of data, enabling the analysts to concentrate on subsets of data that represent activities of interest. The CAA has potential for use in a variety of governmental and commercial applications, including planning for crews for future long space flights, designing facilities wherein humans must work in proximity for long times, improving crew training and measuring crew performance in military settings, human-factors and safety assessment, development of team procedures, and behavioral and ethnographic research. The data-acquisition hardware of the CAA (see figure) includes two video cameras: an overhead one aimed upward at a paraboloidal mirror on the ceiling and one mounted on a wall aimed in a downward slant toward the crew area. As many as four wireless microphones can be worn by crew members. The audio signals received from the microphones are digitized, then compressed in preparation for storage. Approximate locations of as many as four crew members are measured by use of a Cricket indoor location system. [The Cricket indoor location system includes ultrasonic/radio beacon and listener units. A Cricket beacon (in this case, worn by a crew member) simultaneously transmits a pulse of ultrasound and a radio signal that contains identifying information. Each Cricket listener unit measures the difference between the times of reception of the ultrasound and radio signals from an identified beacon

  6. Soft Decision Analyzer

    Science.gov (United States)

    Steele, Glen; Lansdowne, Chatwin; Zucha, Joan; Schlensinger, Adam

    2013-01-01

    The Soft Decision Analyzer (SDA) is an instrument that combines hardware, firmware, and software to perform realtime closed-loop end-to-end statistical analysis of single- or dual- channel serial digital RF communications systems operating in very low signal-to-noise conditions. As an innovation, the unique SDA capabilities allow it to perform analysis of situations where the receiving communication system slips bits due to low signal-to-noise conditions or experiences constellation rotations resulting in channel polarity in versions or channel assignment swaps. SDA s closed-loop detection allows it to instrument a live system and correlate observations with frame, codeword, and packet losses, as well as Quality of Service (QoS) and Quality of Experience (QoE) events. The SDA s abilities are not confined to performing analysis in low signal-to-noise conditions. Its analysis provides in-depth insight of a communication system s receiver performance in a variety of operating conditions. The SDA incorporates two techniques for identifying slips. The first is an examination of content of the received data stream s relation to the transmitted data content and the second is a direct examination of the receiver s recovered clock signals relative to a reference. Both techniques provide benefits in different ways and allow the communication engineer evaluating test results increased confidence and understanding of receiver performance. Direct examination of data contents is performed by two different data techniques, power correlation or a modified Massey correlation, and can be applied to soft decision data widths 1 to 12 bits wide over a correlation depth ranging from 16 to 512 samples. The SDA detects receiver bit slips within a 4 bits window and can handle systems with up to four quadrants (QPSK, SQPSK, and BPSK systems). The SDA continuously monitors correlation results to characterize slips and quadrant change and is capable of performing analysis even when the

  7. Analysis of short circuit transfer behavior using acoustic signal detection

    Directory of Open Access Journals (Sweden)

    Eakkachai Warinsiriruk

    2013-06-01

    Full Text Available The stability of a short circuiting period is important to obtain the desired weld quality. The objective of this research is to analyze the uniformity of liquid bridge disruption period during short circuit mode affected by various shielding gas compositions. The shielding gas compositions of 100% CO2 and 84%Ar+2%O2+14%CO2 were used in this study. Short circuiting period was detected by using acoustic signals emitting from the arc. Acoustic data were recorded by using multimedia function of XP windows audio card through a high sensitivity microphone. The results of short circuit acoustic data were analyzed by using continuous wavelet transformation for classifying the difference of acoustic emitting mechanism of electrode tip touching with base metal and pinching cut-off. For 84%Ar+2%O2+14%CO2 shielding gas, it clearly showed smoothershort circuit transfer than that of CO2 shielding gas. CO2 shielding gas gave large variation in disruption period comparing with that of 84%Ar+2%O2+14%CO2 gas mixture.

  8. Distortion Cancellation via Polyphase Multipath Circuits

    OpenAIRE

    Mensink, Eisse; Klumperink, Eric A.M.; Nauta, Bram

    2004-01-01

    The central question of this paper is: can we enhance the spectral purity of nonlinear circuits with the help of polyphase multipath circuits. Polyphase multipath circuits are circuits with two or more paths that exploit phase differences between the paths to cancel unwanted signals. It turns out that it is very well possible to cancel distortion products produced by a nonlinear circuit. Unfortunately, there are also some spectral components that cannot be cancelled with the polyphase multipa...

  9. Instrumentation and test gear circuits manual

    CERN Document Server

    Marston, R M

    2013-01-01

    Instrumentation and Test Gear Circuits Manual provides diagrams, graphs, tables, and discussions of several types of practical circuits. The practical circuits covered in this book include attenuators, bridges, scope trace doublers, timebases, and digital frequency meters. Chapter 1 discusses the basic instrumentation and test gear principles. Chapter 2 deals with the design of passive attenuators, and Chapter 3 with passive and active filter circuits. The subsequent chapters tackle 'bridge' circuits, analogue and digital metering techniques and circuitry, signal and waveform generation, and p

  10. A New Method for Constructing Circuit Codes

    OpenAIRE

    Byrnes, Kevin M.

    2016-01-01

    Circuit codes are constructed from induced cycles in the graph of the $n$ dimensional hypercube. They are both theoretically and practically important, as circuit codes can be used as error correcting codes. When constructing circuit codes, the length of the cycle determines its accuracy and a parameter called the spread determines how many errors it can detect. We present a new method for constructing a circuit code of spread $k+1$ from a circuit code of spread $k$. This method leads to reco...

  11. Factors Mediating the Effect of Gender on Ninth-Grade Turkish Students' Misconceptions Concerning Electric Circuits

    Science.gov (United States)

    Sencar, Selen; Eryilmaz, Ali

    2004-01-01

    This study was designed to identify and analyze possible factors that mediate the effect of gender on ninth-grade Turkish students' misconceptions concerning electric circuits. A Simple Electric Circuit Concept Test (SECCT), including items with both practical and theoretical contexts, and an Interest-Experience Questionnaire about Electricity…

  12. A comparison study of on-chip short pulse generation circuits based on a coplanar waveguide

    Institute of Scientific and Technical Information of China (English)

    邹焕; 耿永涛; 王平山; 李家胤

    2011-01-01

    A few traditional pulse-forming circuits are implemented in a commercial 0.13 μm digital complementary-metal-oxide-semiconductor (CMOS) technology. These circuits, based on a coplanar waveguide, are analyzed and compared through CadenceTM Spectre simulati

  13. State-variable analysis of non-linear circuits with a desk computer

    Science.gov (United States)

    Cohen, E.

    1981-01-01

    State variable analysis was used to analyze the transient performance of non-linear circuits on a desk top computer. The non-linearities considered were not restricted to any circuit element. All that is required for analysis is the relationship defining each non-linearity be known in terms of points on a curve.

  14. Soft switching DC/DC converter using controlled output rectifier with auxiliary circuit

    OpenAIRE

    Dudrik, Jaroslav; BODOR Marcel; TRIP Daniel Nistor

    2010-01-01

    Auxiliary circuit for DC/DC converter withcontrolled output rectifier is presented in this paper.Soft switching for power switches of the inverter isachieved by using controlled output rectifier and softswitching of the controlled rectifier by using losslessauxiliary circuit. The principle of converter operationis explained and analyzed and experimental results onthe laboratory model are presented.

  15. Theory and Practice of Chinese-English Bilingual Teaching in Circuit Course

    Science.gov (United States)

    Chen, Xiao

    2008-01-01

    The Chinese-English bilingual teaching in the circuit course is an important approach to foster innovational talents for the electronic industry in the new century. In this article, we analyze the background, applicability and feasibility of bilingual teaching in the course of circuit and the difficulties facing in the process of implementation.…

  16. Modern approaches to the design of analog-digit integrated circuits based on multilevel simulation methods

    International Nuclear Information System (INIS)

    Modern methods for the design of analog and analog-digit integrated circuits have been analyzed. “Top-down” and “bottom-up” design methods are compared. The advantages of the “top-down” method in the rate of the development and verification of integrated circuits have been demonstrated

  17. Introduction to lethal circuit transformations

    Science.gov (United States)

    Fišer, Petr; Schmidt, Jan

    2015-12-01

    Logic optimization is a process that takes a logic circuit description (Boolean network) as an input and tries to refine it, to reduce its size and/or depth. An ideal optimization process should be able to devise an optimum implementation of a network in a reasonable time, given any circuit structure at the input. However, there are cases where it completely fails to produce even near-optimum solutions. Such cases are typically induced by non-standard circuit structure modifications. Surprisingly enough, such deviated structures are frequently present in standard benchmark sets too. We may only wonder whether it is an intention of the benchmarks creators, or just an unlucky coincidence. Even though synthesis tools should be primarily well suited for practical circuits, there is no guarantee that, e.g., a higher-level synthesis process will not generate such unlucky structures. Here we present examples of circuit transformations that lead to failure of most of state-of-the-art logic synthesis and optimization processes, both academic and commercial, and suggest actions to mitigate the disturbing effects.

  18. Improved Simulation of Stabilizer Circuits

    CERN Document Server

    Aaronson, S; Aaronson, Scott; Gottesman, Daniel

    2004-01-01

    The Gottesman-Knill theorem says that a stabilizer circuit -- that is, a quantum circuit consisting solely of CNOT, Hadamard, and phase gates -- can be simulated efficiently on a classical computer. This paper improves that theorem in several directions. * By removing the need for Gaussian elimination, we make the simulation algorithm much faster at the cost of a factor-2 increase in the number of bits needed to represent a state. We have implemented the improved algorithm in a freely-available program called CHP (CNOT-Hadamard-Phase), which can handle thousands of qubits easily. * We show that the problem of simulating stabilizer circuits is complete for the classical complexity class ParityL, which means that stabilizer circuits are probably not even universal for classical computation. * We give efficient algorithms for computing the inner product between two stabilizer states, putting any n-qubit stabilizer circuit into a "canonical form" that requires at most O(n^2/log n) gates, and other useful tasks. *...

  19. 30 CFR 75.518 - Electric equipment and circuits; overload and short circuit protection.

    Science.gov (United States)

    2010-07-01

    ... Equipment-General § 75.518 Electric equipment and circuits; overload and short circuit protection. Automatic... electric equipment and circuits against short circuit and overloads. Three-phase motors on all electric... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Electric equipment and circuits; overload...

  20. 30 CFR 77.800 - High-voltage circuits; circuit breakers.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false High-voltage circuits; circuit breakers. 77.800... COAL MINES Surface High-Voltage Distribution § 77.800 High-voltage circuits; circuit breakers. High-voltage circuits supplying power to portable or mobile equipment shall be protected by suitable...

  1. 49 CFR 236.5 - Design of control circuits on closed circuit principle.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Design of control circuits on closed circuit..., AND APPLIANCES Rules and Instructions: All Systems General § 236.5 Design of control circuits on closed circuit principle. All control circuits the functioning of which affects safety of train...

  2. Toward Integrated μNetwork Analyzer

    Science.gov (United States)

    Kmec, M.; Helbig, M.; Herrmann, R.; Rauschenbach, P.; Sachs, J.; Schilling, K.

    The article deals with recent development steps toward monolithically integrated micro-Network Analyzer (μNA). The device will deploy M-Sequence-based single-chip transceivers with a built-in ultra-wideband wave separation unit in the receiver chains. The introduced on-chip wideband wave separation is realized using an optimized resistive directional coupler combined with a customized differential LNA as detector. The wave separation works almost down to DC, and its upper frequency limit is determined by the performance of the implemented technology (i.e., bridge resistors, transistors, etc.), the selected circuit topology, and the wirings of particular coupler components but also by the IC packaging itself. Even though the upper limit is designed to be compatible with the analog input bandwidth of the receiver circuit [which is about 18 GHz for naked die (Kmec et al., M-Sequence based single chip UWB-radar sensor. ANTEM/AMEREM 2010 Conference, Ottawa, 2010)], the packaged IC is intended for use up to 8 GHz. Finally, the discussed transceiver is a further development of the mother SiGe System-on-Chip (SoC) presented in the work cited above.

  3. Circuit model of Rimfire switch

    International Nuclear Information System (INIS)

    A cascade gaps circuit model for Rimfire switch has been developed. The circuit model includes all stray capacitances and spark channel on-state conduction characteristics. It can not only describe the behavior of Rimfire switch, but also allow analysis of the time varying voltage and current at each part of the switch, describing the internal characters of the switch. PSpice was used to implement the cascade gaps circuit model and simulate a 700 kV Rimfire switch. The simulation shows that, the voltage of the whole switch will be higher than 700 kV when the laser triggered section has broken down but all cascade gaps keep dielectric, and the voltage of all gaps attenuates with high frequency oscillation. (authors)

  4. Additive Manufacturing of Hybrid Circuits

    Science.gov (United States)

    Sarobol, Pylin; Cook, Adam; Clem, Paul G.; Keicher, David; Hirschfeld, Deidre; Hall, Aaron C.; Bell, Nelson S.

    2016-07-01

    There is a rising interest in developing functional electronics using additively manufactured components. Considerations in materials selection and pathways to forming hybrid circuits and devices must demonstrate useful electronic function; must enable integration; and must complement the complex shape, low cost, high volume, and high functionality of structural but generally electronically passive additively manufactured components. This article reviews several emerging technologies being used in industry and research/development to provide integration advantages of fabricating multilayer hybrid circuits or devices. First, we review a maskless, noncontact, direct write (DW) technology that excels in the deposition of metallic colloid inks for electrical interconnects. Second, we review a complementary technology, aerosol deposition (AD), which excels in the deposition of metallic and ceramic powder as consolidated, thick conformal coatings and is additionally patternable through masking. Finally, we show examples of hybrid circuits/devices integrated beyond 2-D planes, using combinations of DW or AD processes and conventional, established processes.

  5. Vertically Integrated Circuits at Fermilab

    Energy Technology Data Exchange (ETDEWEB)

    Deptuch, Grzegorz; Demarteau, Marcel; Hoff, James; Lipton, Ronald; Shenai, Alpana; Trimpl, Marcel; Yarema, Raymond; Zimmerman, Tom; /Fermilab

    2009-01-01

    The exploration of the vertically integrated circuits, also commonly known as 3D-IC technology, for applications in radiation detection started at Fermilab in 2006. This paper examines the opportunities that vertical integration offers by looking at various 3D designs that have been completed by Fermilab. The emphasis is on opportunities that are presented by through silicon vias (TSV), wafer and circuit thinning and finally fusion bonding techniques to replace conventional bump bonding. Early work by Fermilab has led to an international consortium for the development of 3D-IC circuits for High Energy Physics. The consortium has submitted over 25 different designs for the Fermilab organized MPW run organized for the first time.

  6. Nuclear sensor signal processing circuit

    Science.gov (United States)

    Kallenbach, Gene A.; Noda, Frank T.; Mitchell, Dean J.; Etzkin, Joshua L.

    2007-02-20

    An apparatus and method are disclosed for a compact and temperature-insensitive nuclear sensor that can be calibrated with a non-hazardous radioactive sample. The nuclear sensor includes a gamma ray sensor that generates tail pulses from radioactive samples. An analog conditioning circuit conditions the tail-pulse signals from the gamma ray sensor, and a tail-pulse simulator circuit generates a plurality of simulated tail-pulse signals. A computer system processes the tail pulses from the gamma ray sensor and the simulated tail pulses from the tail-pulse simulator circuit. The nuclear sensor is calibrated under the control of the computer. The offset is adjusted using the simulated tail pulses. Since the offset is set to zero or near zero, the sensor gain can be adjusted with a non-hazardous radioactive source such as, for example, naturally occurring radiation and potassium chloride.

  7. Fault Testing for Reversible Circuits

    CERN Document Server

    Patel, K N; Markov, I L; Patel, Ketan N.; Hayes, John P.; Markov, Igor L.

    2004-01-01

    Applications of reversible circuits can be found in the fields of low-power computation, cryptography, communications, digital signal processing, and the emerging field of quantum computation. Furthermore, prototype circuits for low-power applications are already being fabricated in CMOS. Regardless of the eventual technology adopted, testing is sure to be an important component in any robust implementation. We consider the test set generation problem. Reversibility affects the testing problem in fundamental ways, making it significantly simpler than for the irreversible case. For example, we show that any test set that detects all single stuck-at faults in a reversible circuit also detects all multiple stuck-at faults. We present efficient test set constructions for the standard stuck-at fault model as well as the usually intractable cell-fault model. We also give a practical test set generation algorithm, based on an integer linear programming formulation, that yields test sets approximately half the size o...

  8. Design automation for integrated circuits

    Science.gov (United States)

    Newell, S. B.; de Geus, A. J.; Rohrer, R. A.

    1983-04-01

    Consideration is given to the development status of the use of computers in automated integrated circuit design methods, which promise the minimization of both design time and design error incidence. Integrated circuit design encompasses two major tasks: error specification, in which the goal is a logic diagram that accurately represents the desired electronic function, and physical specification, in which the goal is an exact description of the physical locations of all circuit elements and their interconnections on the chip. Design automation not only saves money by reducing design and fabrication time, but also helps the community of systems and logic designers to work more innovatively. Attention is given to established design automation methodologies, programmable logic arrays, and design shortcuts.

  9. Embedded systems circuits and programming

    CERN Document Server

    Sanchez, Julio

    2012-01-01

    During the development of an engineered product, developers often need to create an embedded system--a prototype--that demonstrates the operation/function of the device and proves its viability. Offering practical tools for the development and prototyping phases, Embedded Systems Circuits and Programming provides a tutorial on microcontroller programming and the basics of embedded design. The book focuses on several development tools and resources: Standard and off-the-shelf components, such as input/output devices, integrated circuits, motors, and programmable microcontrollers The implementat

  10. Circuit modeling for electromagnetic compatibility

    CERN Document Server

    Darney, Ian B

    2013-01-01

    Very simply, electromagnetic interference (EMI) costs money, reduces profits, and generally wreaks havoc for circuit designers in all industries. This book shows how the analytic tools of circuit theory can be used to simulate the coupling of interference into, and out of, any signal link in the system being reviewed. The technique is simple, systematic and accurate. It enables the design of any equipment to be tailored to meet EMC requirements. Every electronic system consists of a number of functional modules interconnected by signal links and power supply lines. Electromagnetic interference

  11. Simplified design of filter circuits

    CERN Document Server

    Lenk, John

    1999-01-01

    Simplified Design of Filter Circuits, the eighth book in this popular series, is a step-by-step guide to designing filters using off-the-shelf ICs. The book starts with the basic operating principles of filters and common applications, then moves on to describe how to design circuits by using and modifying chips available on the market today. Lenk's emphasis is on practical, simplified approaches to solving design problems.Contains practical designs using off-the-shelf ICsStraightforward, no-nonsense approachHighly illustrated with manufacturer's data sheets

  12. Fermionic models with superconducting circuits

    Energy Technology Data Exchange (ETDEWEB)

    Las Heras, Urtzi; Garcia-Alvarez, Laura; Mezzacapo, Antonio; Lamata, Lucas [University of the Basque Country UPV/EHU, Department of Physical Chemistry, Bilbao (Spain); Solano, Enrique [University of the Basque Country UPV/EHU, Department of Physical Chemistry, Bilbao (Spain); IKERBASQUE, Basque Foundation for Science, Bilbao (Spain)

    2015-12-01

    We propose a method for the efficient quantum simulation of fermionic systems with superconducting circuits. It consists in the suitable use of Jordan-Wigner mapping, Trotter decomposition, and multiqubit gates, be with the use of a quantum bus or direct capacitive couplings. We apply our method to the paradigmatic cases of 1D and 2D Fermi-Hubbard models, involving couplings with nearest and next-nearest neighbours. Furthermore, we propose an optimal architecture for this model and discuss the benchmarking of the simulations in realistic circuit quantum electrodynamics setups. (orig.)

  13. Short-circuit impedance measurement

    DEFF Research Database (Denmark)

    Pedersen, Knud Ole Helgesen; Nielsen, Arne Hejde; Poulsen, Niels Kjølstad

    2003-01-01

    Methods for estimating the short-circuit impedance in the power grid are investigated for various voltage levels and situations. The short-circuit impedance is measured, preferably from naturally occurring load changes in the grid, and it is shown that such a measurement system faces different...... kinds of problems at different locations in the grid. This means that the best measurement methodology changes depending on the location in the grid. Three typical examples with different measurement problems at 400 kV, 132 kV and 400 V voltage level are discussed....

  14. Circuit, Thermal and Cost Characteristics of Impulse Magnetizing Circuits

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    This paper describes the development of circuit, thermal and cost model for a capacitor discharge impulse megnetizer and compares simulations to measurements from an actual system. We used a cost structure consisting of five major subsystems for cost modeling. Especially, we estimated the potential for cost reductions impulse magnetizer as a function of time using the learning curve.

  15. TERRITORY, MUSIC AND DISSEMINATION OF INFORMATION: THE SOUND CIRCUIT IN CAMPINAS-SP

    Directory of Open Access Journals (Sweden)

    Cristiano Nunes Alves

    2013-08-01

    Full Text Available This research examines the formation and the thickness of the circuits of radio FM and the music production in Campinas. The circuit FM in Campinas falls in the field of cultural industry since the decade of 1970, and has been expanding in the context of urbanization and metropolis growing in Brazil. Today this circuit incorporates a bigger system, coupled with the strategies of vertical use of the territory. We noticed that in contrast to the circuit FM, some residual musical component in places involves, among others, the alternative production and free radios. These circuits involved by a technically and territorial division of labor spurred by circuits upside of information, survive to the urban division and fragmentation. It is, therefore, a study of Campinas as a place that houses technical, informational and communicational densities. We analyzed geographical conditions of contemporary life in this city, inquiring about the communication component in the use of the territory.

  16. Self- Balanced Charge Pump with Fast Lock Circuit

    Institute of Scientific and Technical Information of China (English)

    JIANG Xiang; ZOU Xuecheng; XIAO Dingzhong; LIU Sanqing

    2006-01-01

    A self-balanced charge pump (CP) with fast lock circuit to achieve nearly zero phase error is proposed and analyzed. The proposed CP is designed based on the SMIC 0.25 μm 1P5M complementary metal-oxide semiconductor (CMOS) process with a 2.5 V supply voltage. HSPICE simulation shows that even if the mismatch of phase/frequency detector (PFD) was beyond 10%, the charge pump could still keep nearly zero phase error. Incorporated fast lock circuit can shorten start-up time to below 300 ns.

  17. Magneto-sensor circuit efficiency incremented by Fourier-transformation

    KAUST Repository

    Talukdar, Abdul Hafiz Ibne

    2011-10-01

    In this paper detection by recognized intelligent algorithm for different magnetic films with the aid of a cost-effective and simple high efficient circuit are realized. Well-known, magnetic films generate oscillating frequencies when they stay a part of an LC- oscillatory circuit. These frequencies can be further analyzed to gather information about their magnetic properties. For the first time in this work we apply the signal analysis in frequency domain to create the Fourier frequency spectra which was used to detect the sample properties and their recognition. In this paper we have summarized both the simulation and experimental results. © 2011 Elsevier Ltd. All rights reserved.

  18. Modeling Of Combinational Circuits Based On Ternary Multiplexer Using VHDL

    Directory of Open Access Journals (Sweden)

    A.Sathish kumar,

    2010-08-01

    Full Text Available This paper presents a novel method for defining, analyzing, testing and implementing the basic combinational circuitry with VHDL Simulator. This paper shows the potential of VHDL modeling and simulation that can be applied to Ternary switching circuits to verify its functionality and timing specifications. A novel method is brought out for implementing the basic combinational circuitry with minimum number of multiplexers. It also includes 1-bit and 2-bit position shifter and Barrel shifter. Method of coding is illustrated with respect to block diagram. An intention is to show how proposed simulator can be used to simulate MVL circuits and to evaluate systemperformance.

  19. Relaxation Based Electrical Simulation for VLSI Circuits

    Directory of Open Access Journals (Sweden)

    S. Rajkumar

    2012-06-01

    Full Text Available Electrical circuit simulation was one of the first CAD tools developed for IC design. The conventional circuit simulators like SPICE and ASTAP were designed initially for the cost effective analysis of circuits containing a few hundred transistors or less. A number of approaches have been used to improve the performances of congenital circuit simulators for the analysis of large circuits. Thereafter relaxation methods was proposed to provide more accurate waveforms than standard circuit simulators with up to two orders of magnitude speed improvement for large circuits. In this paper we have tried to highlights recently used waveform and point relaxation techniques for simulation of VLSI circuits. We also propose a simple parallelization technique and experimentally demonstrate that we can solve digital circuits with tens of million transistors in a few hours.

  20. An Approach to Simplify Reversible Logic Circuits

    Directory of Open Access Journals (Sweden)

    Pabitra Roy

    2012-09-01

    Full Text Available Energy loss is one of the major problems in traditional irreversible circuits. For every bit of information loss kTln2 joules of heat is lost. In order to reduce the energy loss the concept of reversible logic circuits are introduced. Here we have described an algorithm for simplifying the reversible logic circuit and hence reduction of circuit cost and energy. The algorithm considers sub_circuit with respect to their number of lines and contiguous gates. The resulting sub_circuits are re-synthesized with smaller equivalent implementation. The process continues until circuit cost reaches good enough for Application or until a given computation budget has been exhausted. The circuit is constructed by NOT, CNOT and Toffoli gates only. By applying the algorithm and using the equivalent implementation we will get significant reduction of circuit cost and hence energy.

  1. Clocking Scheme for Switched-Capacitor Circuits

    DEFF Research Database (Denmark)

    Steensgaard-Madsen, Jesper

    1998-01-01

    A novel clocking scheme for switched-capacitor (SC) circuits is presented. It can enhance the understanding of SC circuits and the errors caused by MOSFET (MOS) switches. Charge errors, and techniques to make SC circuits less sensitive to them are discussed.......A novel clocking scheme for switched-capacitor (SC) circuits is presented. It can enhance the understanding of SC circuits and the errors caused by MOSFET (MOS) switches. Charge errors, and techniques to make SC circuits less sensitive to them are discussed....

  2. Digital circuit boards mach 1 GHz

    CERN Document Server

    Morrison, Ralph

    2012-01-01

    A unique, practical approach to the design of high-speed digital circuit boards The demand for ever-faster digital circuit designs is beginning to render the circuit theory used by engineers ineffective. Digital Circuit Boards presents an alternative to the circuit theory approach, emphasizing energy flow rather than just signal interconnection to explain logic circuit behavior. The book shows how treating design in terms of transmission lines will ensure that the logic will function, addressing both storage and movement of electrical energy on these lines. It cove

  3. Separating OR, SUM, and XOR Circuits

    OpenAIRE

    Find, Magnus; Göös, Mika; Järvisalo, Matti; Kaski, Petteri; Koivisto, Mikko; Korhonen, Janne H.

    2013-01-01

    Given a boolean n by n matrix A we consider arithmetic circuits for computing the transformation x->Ax over different semirings. Namely, we study three circuit models: monotone OR-circuits, monotone SUM-circuits (addition of non-negative integers), and non-monotone XOR-circuits (addition modulo 2). Our focus is on \\emph{separating} these models in terms of their circuit complexities. We give three results towards this goal: (1) We prove a direct sum type theorem on the monotone complexity of ...

  4. Advanced circuit simulation using Multisim workbench

    CERN Document Server

    Báez-López, David; Cervantes-Villagómez, Ofelia Delfina

    2012-01-01

    Multisim is now the de facto standard for circuit simulation. It is a SPICE-based circuit simulator which combines analog, discrete-time, and mixed-mode circuits. In addition, it is the only simulator which incorporates microcontroller simulation in the same environment. It also includes a tool for printed circuit board design.Advanced Circuit Simulation Using Multisim Workbench is a companion book to Circuit Analysis Using Multisim, published by Morgan & Claypool in 2011. This new book covers advanced analyses and the creation of models and subcircuits. It also includes coverage of transmissi

  5. A circuit mechanism for neurodegeneration.

    Science.gov (United States)

    Roselli, Francesco; Caroni, Pico

    2012-10-12

    How deficiency in SMN1 selectively affects motoneurons in spinal muscular atrophy is poorly understood. Here, Imlach et al. and Lotti et al. show that aberrant splicing of Stasimon in cholinergic sensory neurons and interneurons leads to motoneuron degeneration, suggesting that altered circuit function may underlie the disorder.

  6. Circuit design for RF transceivers

    CERN Document Server

    Leenaerts, Domine; Vaucher, Cicero S

    2007-01-01

    Second edition of this successful 2001 RF Circuit Design book, has been updated, latest technology reviews have been added as well as several actual case studies. Due to the authors being active in industry as well as academia, this should prove to be an essential guide on RF Transceiver Design for students and engineers.

  7. Integrated Circuit Stellar Magnitude Simulator

    Science.gov (United States)

    Blackburn, James A.

    1978-01-01

    Describes an electronic circuit which can be used to demonstrate the stellar magnitude scale. Six rectangular light-emitting diodes with independently adjustable duty cycles represent stars of magnitudes 1 through 6. Experimentally verifies the logarithmic response of the eye. (Author/GA)

  8. Unbalanced Neuronal Circuits in Addiction

    OpenAIRE

    Volkow, Nora D; Wang, Gen-Jack; Tomasi, Dardo; Baler, Ruben D.

    2013-01-01

    Through sequential waves of drug-induced neurochemical stimulation, addiction co-opts the brain's neuronal circuits that mediate reward, motivation, , to behavioral inflexibility and a severe disruption of self-control and compulsive drug intake. Brain imaging technologies have allowed neuroscientists to map out the neural landscape of addiction in the human brain and to understand how drugs modify it.

  9. [Modeling and analysis of volume conduction based on field-circuit coupling].

    Science.gov (United States)

    Tang, Zhide; Liu, Hailong; Xie, Xiaohui; Chen, Xiufa; Hou, Deming

    2012-08-01

    Numerical simulations of volume conduction can be used to analyze the process of energy transfer and explore the effects of some physical factors on energy transfer efficiency. We analyzed the 3D quasi-static electric field by the finite element method, and developed A 3D coupled field-circuit model of volume conduction basing on the coupling between the circuit and the electric field. The model includes a circuit simulation of the volume conduction to provide direct theoretical guidance for energy transfer optimization design. A field-circuit coupling model with circular cylinder electrodes was established on the platform of the software FEM3.5. Based on this, the effects of electrode cross section area, electrode distance and circuit parameters on the performance of volume conduction system were obtained, which provided a basis for optimized design of energy transfer efficiency.

  10. Digital logic circuit design with ALTERA MAX+PLUS II

    International Nuclear Information System (INIS)

    This book is composed of five parts. The first part has introduction of ALTERA MAX+PLUS II and graphic editor, text editor, compiler, waveform editor simulator and timing analyzer of it. The second part is about direction of digital logic circuit design with training kit. The third part has grammar and practice of VHDL in ALTERA MAX+PLUS II including example and history of VHDL. The fourth part shows the design example of digital logic circuit by VHDL of ALTERA MAX+PLUS II which lists designs of adder and subtractor, code converter, counter, state machine and LCD module. The last part explains design example of digital logic circuit by graphic editor in ALTERA MAX+PLUS II.

  11. Cell Mapping for Nanohybrid Circuit Architecture Using Genetic Algorithm

    Institute of Scientific and Technical Information of China (English)

    Zhu-Fei Chu; Yin-Shui Xia; Lun-Yao Wang

    2012-01-01

    Nanoelectronics constructed by nanoscale devices seems promising for the advanced development of integrated circuits (ICs). However,the lack of computer aided design (CAD) tools seriously hinders its development and applications.To investigate the cell mapping task in CAD flow,we present a genetic algorithm (GA) based method for Cmos/nanowire/MOLecular hybrid (CMOL),which is a nanohybrid circuit architecture.By designing several crossover operators and analyzing their performance,an efficient crossover operator is proposed.Combining a mutation operator,a GA based algorithm is presented and tested on the International Symposium on Circuits and Systems (ISCAS) benchmarks.The results show that the proposed method not only can obtain better area utilization and smaller delay,but also can handle larger benchmarks with CPU time improvement compared with the published methods.

  12. Derivation of Neural Circuits from the Similarity Matching Principle

    Science.gov (United States)

    Pehlevan, Cengiz; Chklovskii, Dmitri

    Our brains analyze high-dimensional datasets streamed by our sensory organs in multiple stages. Sensory cortices, for example, perform tasks like dimensionality reduction, sparse feature discovery and clustering. To model these tasks we pursue an approach analogous to use of action principles in physics and propose a new family of objective functions based on the principle of similarity matching. From these objective functions we derive online distributed algorithms that can be implemented by biological neural networks resembling cortical circuits. Our networks can adapt to changes in the number of latent dimensions or the number of clusters in the input dataset. Furthermore, we formulate minimax optimization problems from which we derive online algorithms with two classes of neurons identified with principal neurons and interneurons in biological circuits. In addition to bearing resemblance to biological circuits, our algorithms are competitive for Big Data applications.

  13. Quantum circuit physical design methodology with emphasis on physical synthesis

    Science.gov (United States)

    Mohammadzadeh, Naser; Saheb Zamani, Morteza; Sedighi, Mehdi

    2013-11-01

    In our previous works, we have introduced the concept of "physical synthesis" as a method to consider the mutual effects of quantum circuit synthesis and physical design. While physical synthesis can involve various techniques to improve the characteristics of the resulting quantum circuit, we have proposed two techniques (namely gate exchanging and auxiliary qubit selection) to demonstrate the effectiveness of the physical synthesis. However, the previous contributions focused mainly on the physical synthesis concept, and the techniques were proposed only as a proof of concept. In this paper, we propose a methodological framework for physical synthesis that involves all previously proposed techniques along with a newly introduced one (called auxiliary qubit insertion). We will show that the entire flow can be seen as one monolithic methodology. The proposed methodology is analyzed using a large set of benchmarks. Experimental results show that the proposed methodology decreases the average latency of quantum circuits by about 36.81 % for the attempted benchmarks.

  14. High performance BGMI circuit for VLWIR FPAs

    Science.gov (United States)

    Hao, Li-chao; Chen, Hong-lei; Huang, Ai-bo; Zhang, Jun-ling; Ding, Rui-jun

    2013-09-01

    An improved CMOS readout integrated circuit (ROIC) for N-on-P very long wavelength (VLWIR) detectors is designed, which has the ability to operate with a simple background suppression. It increases the integration time and the signal-to-noise ratio (SNR) of image data. A buffered gate modulation input (BGMI) cell as input circuit provides a low input resistance, high injection efficiency, and precise biasing voltage to the photodiode. By theoretically analyzing the characteristic parameters of MOS device at low temperature, a high gain's feedback amplifier is devised which using a differential stage to provide the inverting gain to improve linearity and to provide tight control of the detector bias. The final chip is fabricated with HHNEC 0.35um 1P4M process technology. The measurement results of the fabricated readout chip under 50K have successfully verified both readout function and performance improvement. With the 5.0V power supply, ROIC provides the output dynamic range over 2.5V. At the same time, the total power dissipation is less than 200mW, and the maximum readout speed is more than 2.5MHz.

  15. The technology on noise reduction of the APD detection circuit

    Science.gov (United States)

    Wu, Xue-ying; Zheng, Yong-chao; Cui, Jian-yong

    2013-09-01

    The laser pulse detection is widely used in the field of laser range finders, laser communications, laser radar, laser Identification Friend or Foe, et al, for the laser pulse detection has the advantage of high accuracy, high sensitivity and strong anti-interference. The avalanche photodiodes (APD) has the advantage of high quantum efficiency, high response speed and huge gain. The APD is particularly suitable for weak signal detection. The technology that APD acts as the photodetector for weak signal reception and amplification is widely used in laser pulse detection. The APD will convert the laser signal to weak electrical signal. The weak signal is amplified, processed and exported by the circuit. In the circuit design, the optimal signal detection is one key point in photoelectric detection system. The issue discusses how to reduce the noise of the photoelectric signal detection circuit and how to improve the signal-to-noise ratio, related analysis and practice included. The essay analyzes the mathematical model of the signal-to-noise ratio for photoelectric conversion and the noise of the APD photoelectric detection system. By analysis the bandwidth of the detection system is determined, and the circuit devices are selected that match the APD. In the circuit design separated devices with low noise are combined with integrated operational amplifier for the purpose of noise reduction. The methods can effectively suppress the noise, and improve the detection sensitivity.

  16. Performance analysis of a digital capacitance measuring circuit.

    Science.gov (United States)

    Xu, Lijun; Sun, Shijie; Cao, Zhang; Yang, Wuqiang

    2015-05-01

    This paper presents the design and study of a digital capacitance measuring circuit with theoretical analysis, numerical simulation, and experimental evaluation. The static and dynamic performances of the capacitance measuring circuit are first defined, including signal-to-noise ratio (SNR), standard deviation, accuracy, linearity, sensitivity, and response time, within a given measurement range. Then numerical simulation is carried out to analyze the SNR and standard deviation of the circuit, followed by experiments to validate the overall performance of the circuit. The simulation results show that when the standard deviation of noise is 0.08 mV and the measured capacitance decreases from 6 pF to 3 fF, the SNR decreases from 90 dB to 22 dB and the standard deviation is between 0.17 fF and 0.24 fF. The experimental results show that when the measured capacitance decreases from 6 pF to 40 fF and the data sampled in a single period are used for demodulation, the SNR decreases from 88 dB to 40 dB and the standard deviation is between 0.18 fF and 0.25 fF. The maximum absolute error and relative error are 5.12 fF and 1.26%, respectively. The SNR and standard deviation can be further improved if the data sampled in more than one period are used for demodulation by the circuit.

  17. The voltage-current relationship and equivalent circuit implementation of parallel flux-controlled memristive circuits

    Institute of Scientific and Technical Information of China (English)

    Bao Bo-Cheng; Feng Fei; Dong Wei; Pan Sai-Hu

    2013-01-01

    A flux-controlled memristor characterized by smooth cubic nonlinearity is taken as an example,upon which the voltage-current relationships (VCRs) between two parallel memristive circuits-a parallel memristor and capacitor circuit (the parallel MC circuit),and a parallel memristor and inductor circuit (the parallel ML circuit)-are investigated.The results indicate that the VCR between these two parallel memristive circuits is closely related to the circuit parameters,and the frequency and amplitude of the sinusoidal voltage stimulus.An equivalent circuit model of the memristor is built,upon which the circuit simulations and experimental measurements of both the parallel MC circuit and the parallel ML circuit are performed,and the results verify the theoretical analysis results.

  18. Analog Nonvolatile Computer Memory Circuits

    Science.gov (United States)

    MacLeod, Todd

    2007-01-01

    In nonvolatile random-access memory (RAM) circuits of a proposed type, digital data would be stored in analog form in ferroelectric field-effect transistors (FFETs). This type of memory circuit would offer advantages over prior volatile and nonvolatile types: In a conventional complementary metal oxide/semiconductor static RAM, six transistors must be used to store one bit, and storage is volatile in that data are lost when power is turned off. In a conventional dynamic RAM, three transistors must be used to store one bit, and the stored bit must be refreshed every few milliseconds. In contrast, in a RAM according to the proposal, data would be retained when power was turned off, each memory cell would contain only two FFETs, and the cell could store multiple bits (the exact number of bits depending on the specific design). Conventional flash memory circuits afford nonvolatile storage, but they operate at reading and writing times of the order of thousands of conventional computer memory reading and writing times and, hence, are suitable for use only as off-line storage devices. In addition, flash memories cease to function after limited numbers of writing cycles. The proposed memory circuits would not be subject to either of these limitations. Prior developmental nonvolatile ferroelectric memories are limited to one bit per cell, whereas, as stated above, the proposed memories would not be so limited. The design of a memory circuit according to the proposal must reflect the fact that FFET storage is only partly nonvolatile, in that the signal stored in an FFET decays gradually over time. (Retention times of some advanced FFETs exceed ten years.) Instead of storing a single bit of data as either a positively or negatively saturated state in a ferroelectric device, each memory cell according to the proposal would store two values. The two FFETs in each cell would be denoted the storage FFET and the control FFET. The storage FFET would store an analog signal value

  19. Driver circuit for solid state light sources

    Energy Technology Data Exchange (ETDEWEB)

    Palmer, Fred; Denvir, Kerry; Allen, Steven

    2016-02-16

    A driver circuit for a light source including one or more solid state light sources, a luminaire including the same, and a method of so driving the solid state light sources are provided. The driver circuit includes a rectifier circuit that receives an alternating current (AC) input voltage and provides a rectified AC voltage. The driver circuit also includes a switching converter circuit coupled to the light source. The switching converter circuit provides a direct current (DC) output to the light source in response to the rectified AC voltage. The driver circuit also includes a mixing circuit, coupled to the light source, to switch current through at least one solid state light source of the light source in response to each of a plurality of consecutive half-waves of the rectified AC voltage.

  20. Plug-in integrated/hybrid circuit

    Science.gov (United States)

    Stringer, E. J.

    1974-01-01

    Hybrid circuitry can be installed into standard round bayonet connectors, to eliminate wiring from connector to circuit. Circuits can be connected directly into either section of connector pair, eliminating need for hard wiring to that section.

  1. Influences of Resistor-Type Superconducting Fault Current Limiter on Power System Transient Stability with Asymmetrical Short-Circuit Faults

    Institute of Scientific and Technical Information of China (English)

    Xue-Ping Gu; Zhi-Long Yang

    2008-01-01

    The transient stability of a single machine to infinite-busbar power system with resistor- type superconducting fault current limiters (SFCL) is analyzed under asymmetrical short-circuit fault conditions. The SFCL is considered to introduce a resistance into the three-phase circuits when faults occur. Based on the power-angle curves for different short-circuit conditions of the single-line to ground, double-line to ground and line to line short-circuit faults, the influences of the SFCLs on transient stability are analyzed in detail. The time-domain simulation of transient stability is carried out to verify the analytical results.

  2. Brain-machine interface circuits and systems

    CERN Document Server

    Zjajo, Amir

    2016-01-01

    This book provides a complete overview of significant design challenges in respect to circuit miniaturization and power reduction of the neural recording system, along with circuit topologies, architecture trends, and (post-silicon) circuit optimization algorithms. The introduced novel circuits for signal conditioning, quantization, and classification, as well as system configurations focus on optimized power-per-area performance, from the spatial resolution (i.e. number of channels), feasible wireless data bandwidth and information quality to the delivered power of implantable system.

  3. Black hole qubit correspondence from quantum circuits

    CERN Document Server

    Prudencio, Thiago; Silva, Edilberto O; Belich, Humberto

    2014-01-01

    We propose a black hole qubit correspondence (BHQC) from quantum circuits, taking into account the BHQC formulations of wrapped brane qubits. With base on BHQC, we implement the corresponding gate operations to realize any given quantum circuit. In particular, we implement cases of the generation of Bell states, quantum teleportation and GHZ states circuits. Finally, we give an interpretation of the BHQC from quantum circuits with base on the BHQC classification of entanglement classes.

  4. Thermal response of nonequilibrium R C circuits

    Science.gov (United States)

    Baiesi, Marco; Ciliberto, Sergio; Falasco, Gianmaria; Yolcu, Cem

    2016-08-01

    We analyze experimental data obtained from an electrical circuit having components at different temperatures, showing how to predict its response to temperature variations. This illustrates in detail how to utilize a recent linear response theory for nonequilibrium overdamped stochastic systems. To validate these results, we introduce a reweighting procedure that mimics the actual realization of the perturbation and allows extracting the susceptibility of the system from steady-state data. This procedure is closely related to other fluctuation-response relations based on the knowledge of the steady-state probability distribution. As an example, we show that the nonequilibrium heat capacity in general does not correspond to the correlation between the energy of the system and the heat flowing into it. Rather, also nondissipative aspects are relevant in the nonequilibrium fluctuation-response relations.

  5. Thermal response of nonequilibrium RC-circuits

    CERN Document Server

    Baiesi, Marco; Falasco, Gianmaria; Yolcu, Cem

    2016-01-01

    We analyze experimental data obtained from an electrical circuit having components at different temperatures, showing how to predict its response to temperature variations. This illustrates in detail how to utilize a recent linear response theory for nonequilibrium overdamped stochastic systems. To validate these results, we introduce a reweighting procedure that mimics the actual realization of the perturbation and allows extracting the susceptibility of the system from steady state data. This procedure is closely related to other fluctuation-response relations based on the knowledge of the steady state probability distribution. As an example, we show that the nonequilibrium heat capacity in general does not correspond to the correlation between the energy of the system and the heat flowing into it. Rather, also non-dissipative aspects are relevant in the nonequilbrium fluctuation response relations.

  6. Composite behaviors of dual meminductor circuits

    Science.gov (United States)

    Zheng, Ci-Yan; Yu, Dong-Sheng; Liang, Yan; Chen, Meng-Ke

    2015-11-01

    This paper focuses on analyzing the composite dynamic behaviors of two meminductors in serial and parallel connections with different polarities. Based on the constitutive relations, two time-integral-of-flux (TIF) controlled meminductors are adopted to theoretically demonstrate the variation of memductance in terms of TIF, charge, flux, and current. By utilizing a floating memristor-less meminductor emulator, the theoretical analysis reported in this paper is confirmed via a PSPICE simulation study and hardware experiment. Good agreement among theoretical analysis, simulation, and hardware validation confirms that dual meminductor circuits in composite connections behave as a new meminductor with higher complexity. Project supported by the Fundamental Research Funds for the Central Universities, China (Grant No. 2013QNB28.)

  7. Application of Carbon nano tube field-effect transistor as sensor in analyzing of integrated circuits

    International Nuclear Information System (INIS)

    The purpose of this investigation is to develop a current-transport model for Carbon nano tube field effect transistor applicable in the analysis of detection of chemical material. We implemented an efficient numerical model of a Carbon nano tube field-effect transistor with regard to ultrasonic nano welding treatment. Our results have shown a strong dependence of the I-V characteristics on the wrapping angle and diameter of Carbon nano tubes. Also our calculations have indicated that Carbon nano tube field effect transistors based sensors are promising compact ultra-sensitive and ultra low-power advanced miniaturized sensors in comparison to conventional sensors.

  8. 49 CFR 236.721 - Circuit, control.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Circuit, control. 236.721 Section 236.721..., MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Definitions § 236.721 Circuit, control. An electrical circuit between a source of electric energy and a device which it operates....

  9. Equivalence Checking of Hierarchical Combinational Circuits

    DEFF Research Database (Denmark)

    Williams, Poul Frederick; Hulgaard, Henrik; Andersen, Henrik Reif

    1999-01-01

    This paper presents a method for verifying that two hierarchical combinational circuits implement the same Boolean functions. The key new feature of the method is its ability to exploit the modularity of circuits to reuse results obtained from one part of the circuits in other parts. We demonstrate...

  10. An eigenvalue study of the MLC circuit

    DEFF Research Database (Denmark)

    Lindberg, Erik; Murali, K.

    1998-01-01

    The MLC (Murali-Lakshmanan-Chua) circuit is the simplest non-autonomous chaotic circuit. Insight in the behaviour of the circuit is obtained by means of a study of the eigenvalues of the linearized Jacobian of the nonlinear differential equations. The trajectories of the eigenvalues as functions...

  11. An Equivalent Circuit for Landau Damping

    DEFF Research Database (Denmark)

    Pécseli, Hans

    1976-01-01

    An equivalent circuit simulating the effect of Landau damping in a stable plasma‐loaded parallel‐plate capacitor is presented. The circuit contains a double infinity of LC components. The transition from stable to unstable plasmas is simulated by the introduction of active elements into the circuit....

  12. 49 CFR 236.731 - Controller, circuit.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Controller, circuit. 236.731 Section 236.731 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION... Controller, circuit. A device for opening and closing electric circuits....

  13. A Current-mode Logarithmic Function Circuit

    OpenAIRE

    Osama Oglah Faris; Muhammad Taher Abuelma'atti

    2004-01-01

    A new current-mode analog circuit configuration that implements the function ln (x/y) is proposed. The circuit uses bipolar transistors and resistors and is suitable for integration. In the proposed circuit the ratio (x/y) can be larger or smaller than unity. Simulation results are included.

  14. 47 CFR 32.2232 - Circuit equipment.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Circuit equipment. 32.2232 Section 32.2232... FOR TELECOMMUNICATIONS COMPANIES Instructions for Balance Sheet Accounts § 32.2232 Circuit equipment... which is used for the amplification, modulation, regeneration, circuit patching, balancing or control...

  15. 49 CFR 236.726 - Circuit, track.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Circuit, track. 236.726 Section 236.726 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION... Circuit, track. An electrical circuit of which the rails of the track form a part....

  16. 30 CFR 56.6407 - Circuit testing.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Circuit testing. 56.6407 Section 56.6407... Blasting § 56.6407 Circuit testing. A blasting galvanometer or other instrument designed for testing blasting circuits shall be used to test each of the following: (a) Continuity of each electric detonator...

  17. 30 CFR 57.6407 - Circuit testing.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Circuit testing. 57.6407 Section 57.6407... Blasting-Surface and Underground § 57.6407 Circuit testing. A blasting galvanometer or other instrument designed for testing blasting circuits shall be used to test the following: (a) In surface operations—...

  18. 30 CFR 75.1323 - Blasting circuits.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Blasting circuits. 75.1323 Section 75.1323... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Explosives and Blasting § 75.1323 Blasting circuits. (a) Blasting circuits shall be protected from sources of stray electric current. (b) Detonators made...

  19. New Logic Circuit with DC Parametric Excitation

    Science.gov (United States)

    Sugahara, Masanori; Kaneda, Hisayoshi

    1982-12-01

    It is shown that dc parametric excitation is possible in a circuit named JUDO, which is composed of two resistively-connected Josephson junctions. Simulation study proves that the circuit has large gain and properties suitable for the construction of small, high-speed logic circuits.

  20. SIMULATION AND EXPERIMENTAL STUDY OF CHAOS GENERATION IN MICROWAVE BAND USING COLPITTS CIRCUIT

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Chaotic Colpitts circuits with fundamental frequency f* beyond 1GHz are studied by both circuit simulation and experiment using Philips' broadband transistor with threshold frequency of 25GHz. For the basic configuration of Colpitts circuit with f* of about 1.6GHz, broadband continuous power spectra could be obtained from both circuit simulations and experiments. The harmonics of the observed signal from Agilent PSA/ESA spectrum analyzer are as noticeable as far as 12GHz. A modified Colpitts circuit structure employing the parasitic inductance of BJT (Bipolar Junction Transistor) is also proposed and investigated. By circuit simulation, chaotic attractor and broadband continuous power spectra could be obtained from the modified Colpitts circuit with f* of about 3.5GHz. Because the parasitic effects of the prototype board, the experiment result of the modified Colpitts circuit does not agree well with the simulation result. The gap between the simulation and experimental result could be bridged by replacing the lumped circuit elements with distributed ones.

  1. CHEETAH: circuit-switched high-speed end-to-end transport architecture

    Science.gov (United States)

    Veeraraghavan, Malathi; Zheng, Xuan; Lee, Hyuk; Gardner, M.; Feng, Wuchun

    2003-10-01

    Leveraging the dominance of Ethernet in LANs and SONET/SDH in MANs and WANs, we propose a service called CHEETAH (Circuit-switched High-speed End-to-End Transport ArcHitecture). The service concept is to provide end hosts with high-speed, end-to-end circuit connectivity on a call-by-call shared basis, where a "circuit" consists of Ethernet segments at the ends that are mapped into Ethernet-over-SONET long-distance circuits. This paper focuses on the file-transfer application for such circuits. For this application, the CHEETAH service is proposed as an add-on to the primary Internet access service already in place for enterprise hosts. This allows an end host that is sending a file to first attempt setting up an end-to-end Ethernet/EoS circuit, and if rejected, fall back to the TCP/IP path. If the circuit setup is successful, the end host will enjoy a much shorter file-transfer delay than on the TCP/IP path. To determine the conditions under which an end host with access to the CHEETAH service should attempt circuit setup, we analyze mean file-transfer delays as a function of call blocking probability in the circuit-switched network, probability of packet loss in the IP network, round-trip times, link rates, and so on.

  2. Integrated circuits for multimedia applications

    DEFF Research Database (Denmark)

    Vandi, Luca

    2007-01-01

    , and it is applied to a broad-band dual-loop receiver architecture in order to boost the linearity performances of the stage. A simplified noise- and linearity analysis of the circuit is derived, and a comparison is provided with a more traditional dual-loop topology (a broad-band stage based on shunt......This work presents several key aspects in the design of RF integrated circuits for portable multimedia devices. One chapter is dedicated to the application of negative-feedback topologies to receiver frontends. A novel feedback technique suitable for common multiplier-based mixers is described......-series feedback), showing a difference in compression point in the order of 10dBm for the same power consumption. The same principle is also applied to a more conventional narrow-band stage in which a single loop is employed in order to enhance noise performances. Noise analysis shows sensible improvements...

  3. Handbook of microwave integrated circuits

    Science.gov (United States)

    Hoffmann, Reinmut K.

    The design and operation of ICs for use in the 0.5-20-GHz range are described in an introductory and reference work for industrial engineers. Chapters are devoted to an overview of microwave IC (MIC) technology, general stripline characteristics, microwave transmission line (MTL) parameters for microstrips with isotropic dielectric substrates, higher-order modes on a microstrip, the effects of metallic enclosure on MTL transmission parameters, losses in microstrips, the measurement of MTL parameters, and MTLs on anisotropic dielectric substrates. Consideration is given to coupled microstrips on dielectric substrates, microstrip discontinuities, radiation from microstrip circuits, MTL variations, coplanar MTLs, slotlines, and spurious modes in MTL circuits. Diagrams, drawings, graphs, and a glossary of symbols are provided.

  4. Ionization tube simmer current circuit

    Science.gov (United States)

    Steinkraus, Jr., Robert F.

    1994-01-01

    A highly efficient flash lamp simmer current circuit utilizes a fifty percent duty cycle square wave pulse generator to pass a current over a current limiting inductor to a full wave rectifier. The DC output of the rectifier is then passed over a voltage smoothing capacitor through a reverse current blocking diode to a flash lamp tube to sustain ionization in the tube between discharges via a small simmer current. An alternate embodiment of the circuit combines the pulse generator and inductor in the form of an FET off line square wave generator with an impedance limited step up output transformer which is then applied to the full wave rectifier as before to yield a similar simmer current.

  5. Delay locked loop integrated circuit.

    Energy Technology Data Exchange (ETDEWEB)

    Brocato, Robert Wesley

    2007-10-01

    This report gives a description of the development of a Delay Locked Loop (DLL) integrated circuit (IC). The DLL was developed and tested as a stand-alone IC test chip to be integrated into a larger application specific integrated circuit (ASIC), the Quadrature Digital Waveform Synthesizer (QDWS). The purpose of the DLL is to provide a digitally programmable delay to enable synchronization between an internal system clock and external peripherals with unknown clock skew. The DLL was designed and fabricated in the IBM 8RF process, a 0.13 {micro}m CMOS process. It was designed to operate with a 300MHz clock and has been tested up to 500MHz.

  6. 30 CFR 75.601-1 - Short circuit protection; ratings and settings of circuit breakers.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Short circuit protection; ratings and settings of circuit breakers. 75.601-1 Section 75.601-1 Mineral Resources MINE SAFETY AND HEALTH... Trailing Cables § 75.601-1 Short circuit protection; ratings and settings of circuit breakers....

  7. Synthetic circuits, devices and modules

    OpenAIRE

    Zhang, Hong; Jiang, Taijiao

    2010-01-01

    The aim of synthetic biology is to design artificial biological systems for novel applications. From an engineering perspective, construction of biological systems of defined functionality in a hierarchical way is fundamental to this emerging field. Here, we highlight some current advances on design of several basic building blocks in synthetic biology including the artificial gene control elements, synthetic circuits and their assemblies into devices and modules. Such engineered basic buildi...

  8. ?Immunetworks?, intersecting circuits and dynamics

    OpenAIRE

    Demongeot, Jacques; Elena, Adrien; Noual, Mathilde; Sené, Sylvain; Thuderoz, Florence

    2011-01-01

    Abstract This paper proposes a study of biological regulatory networks based on a multi-level strategy. Given a network, the first structural level of this strategy consists in analysing the architecture of the network interactions in order to describe it. The second dynamical level consists in relating the patterns found in the architecture to the possible dynamical behaviours of the network. It is known that circuits are the patterns that play the most important part in the dynam...

  9. Microcontroller based Integrated Circuit Tester

    OpenAIRE

    Yousif Taha Yousif Elamin; Abdelrasoul Jabar Alzubaidi

    2015-01-01

    The digital integrated circuit (IC) tester is implemented by using the ATmega32 microcontroller . The microcontroller processes the inputs and outputs and displays the results on a Liquid Crystal Display (LCD). The basic function of the digital IC tester is to test a digital IC for correct logical functioning as described in the truth table and/or function table. The designed model can test digital ICs having 14 pins. Since it is programmable, any number of ICs can be tested . Thi...

  10. Monolithic readout circuits for RHIC

    Energy Technology Data Exchange (ETDEWEB)

    O`Connor, P.; Harder, J. [Brookhaven National Laboratory, Upton, NY (United States)

    1991-12-31

    Several CMOS ASICs have been developed for a proposed RHIC experiment. This paper discusses why ASIC implementation was chosen for certain functions, circuit specifications and the design techniques used to meet them, and results of simulations and early prototypes. By working closely together from an early stage in the planning process, in-house ASIC designers and detector and data acquisition experimenters can achieve optimal use of this important technology.

  11. CIRCUIT SWITCHING VERSUS PACKET SWITCHING

    OpenAIRE

    Sneps-Sneppe, Manfred

    2015-01-01

    Communication specialists around the world are facing the same problem: shifting from circuit switching (CS) to packet switching (CS). Communication service providers are favoring “All-over-IP” technologies hoping to boost their profits by providing multimedia services. The main stakeholder in this field of the paradigm shift is the industry itself: packet switching hardware manufacturers are going to earn billions of dollars and thus pay engineers and journalists many millions for the promot...

  12. An Interpreter for Quantum Circuits

    OpenAIRE

    Lucas Helms; Ruben Gamboa

    2013-01-01

    This paper describes an ACL2 interpreter for "netlists" describing quantum circuits. Several quantum gates are implemented, including the Hadamard gate H, which rotates vectors by 45 degrees, necessitating the use of irrational numbers, at least at the logical level. Quantum measurement presents an especially difficult challenge, because it requires precise comparisons of irrational numbers and the use of random numbers. This paper does not address computation with irrational numbers or the g...

  13. Ultra-low power integrated circuit design circuits, systems, and applications

    CERN Document Server

    Li, Dongmei; Wang, Zhihua

    2014-01-01

    This book describes the design of CMOS circuits for ultra-low power consumption including analog, radio frequency (RF), and digital signal processing circuits (DSP). The book addresses issues from circuit and system design to production design, and applies the ultra-low power circuits described to systems for digital hearing aids and capsule endoscope devices. Provides a valuable introduction to ultra-low power circuit design, aimed at practicing design engineers; Describes all key building blocks of ultra-low power circuits, from a systems perspective; Applies circuits and systems described to real product examples such as hearing aids and capsule endoscopes.

  14. General Voltage Feedback Circuit Model in the Two-Dimensional Networked Resistive Sensor Array

    Directory of Open Access Journals (Sweden)

    JianFeng Wu

    2015-01-01

    Full Text Available To analyze the feature of the two-dimensional networked resistive sensor array, we firstly proposed a general model of voltage feedback circuits (VFCs such as the voltage feedback non-scanned-electrode circuit, the voltage feedback non-scanned-sampling-electrode circuit, and the voltage feedback non-scanned-sampling-electrode circuit. By analyzing the general model, we then gave a general mathematical expression of the effective equivalent resistor of the element being tested in VFCs. Finally, we evaluated the features of VFCs with simulation and test experiment. The results show that the expression is applicable to analyze the VFCs’ performance of parameters such as the multiplexers’ switch resistors, the nonscanned elements, and array size.

  15. CMOS circuit design, layout and simulation

    CERN Document Server

    Baker, R Jacob

    2010-01-01

    The Third Edition of CMOS Circuit Design, Layout, and Simulation continues to cover the practical design of both analog and digital integrated circuits, offering a vital, contemporary view of a wide range of analog/digital circuit blocks including: phase-locked-loops, delta-sigma sensing circuits, voltage/current references, op-amps, the design of data converters, and much more. Regardless of one's integrated circuit (IC) design skill level, this book allows readers to experience both the theory behind, and the hands-on implementation of, complementary metal oxide semiconductor (CMOS) IC design via detailed derivations, discussions, and hundreds of design, layout, and simulation examples.

  16. Method and Circuit for Injecting a Precise Amount of Charge onto a Circuit Node

    Science.gov (United States)

    Hancock, Bruce R. (Inventor)

    2016-01-01

    A method and circuit for injecting charge into a circuit node, comprising (a) resetting a capacitor's voltage through a first transistor; (b) after the resetting, pre-charging the capacitor through the first transistor; and (c) after the pre-charging, further charging the capacitor through a second transistor, wherein the second transistor is connected between the capacitor and a circuit node, and the further charging draws charge through the second transistor from the circuit node, thereby injecting charge into the circuit node.

  17. Design of superconductor frame compression circuits

    Science.gov (United States)

    Sakurai, T.; Miyaho, N.; Miyahara, K.

    2007-10-01

    We proposed previously a novel interface circuit which was used between semiconductor data-input circuits and superconductor high-speed routers. The frame length of data packets is compressed in the interface circuit. Our proposed interface circuit has rather narrow timing margin. The problem was that our control circuit of the interface circuit could allow only very small timing delay. In this paper we propose a modified control circuit. We have improved the timing margin of the control circuit using RS-flip flop (RS-FF), where two shift registers and one control circuit are driven by clock pulses provided from a master clock-pulse generator. In this circuit, we have assumed fixed frame length packets. Our final target of master clock frequency is 100 GHz which will be realized with the device-parameter set of future advanced process. As the first step of realizing this target value, we aimed at 40 GHz clock operation with the conventional device-parameter set of NECs standard I process. The behavior of the whole frame compression circuit was simulated by a computer, and it was confirmed that it operated properly up to the master clock frequency of 23 GHz.

  18. Model Order Reduction for Electronic Circuits:

    DEFF Research Database (Denmark)

    Hjorth, Poul G.; Shontz, Suzanne

    Electronic circuits are ubiquitous; they are used in numerous industries including: the semiconductor, communication, robotics, auto, and music industries (among many others). As products become more and more complicated, their electronic circuits also grow in size and complexity. This increased...... the need for circuit simulators to evaluate potential designs before fabrication, as integrated circuit prototypes are expensive to build, and troubleshooting is difficult. In this report, we focus on the simulation of printed circuit boards (PCB’s) and interconnects both of which are of great importance...... in the semiconductor industry. Circuit simulation proceeds by using Maxwell’s equations to create a mathematical model of the circuit. The boundary element method is then used to discretize the equations, and the variational form of the equations are then solved on the graph network....

  19. Auto-programmable impulse neural circuits

    Science.gov (United States)

    Watula, D.; Meador, J.

    1990-01-01

    Impulse neural networks use pulse trains to communicate neuron activation levels. Impulse neural circuits emulate natural neurons at a more detailed level than that typically employed by contemporary neural network implementation methods. An impulse neural circuit which realizes short term memory dynamics is presented. The operation of that circuit is then characterized in terms of pulse frequency modulated signals. Both fixed and programmable synapse circuits for realizing long term memory are also described. The implementation of a simple and useful unsupervised learning law is then presented. The implementation of a differential Hebbian learning rule for a specific mean-frequency signal interpretation is shown to have a straightforward implementation using digital combinational logic with a variation of a previously developed programmable synapse circuit. This circuit is expected to be exploited for simple and straightforward implementation of future auto-adaptive neural circuits.

  20. Graphene radio frequency receiver integrated circuit.

    Science.gov (United States)

    Han, Shu-Jen; Garcia, Alberto Valdes; Oida, Satoshi; Jenkins, Keith A; Haensch, Wilfried

    2014-01-01

    Graphene has attracted much interest as a future channel material in radio frequency electronics because of its superior electrical properties. Fabrication of a graphene integrated circuit without significantly degrading transistor performance has proven to be challenging, posing one of the major bottlenecks to compete with existing technologies. Here we present a fabrication method fully preserving graphene transistor quality, demonstrated with the implementation of a high-performance three-stage graphene integrated circuit. The circuit operates as a radio frequency receiver performing signal amplification, filtering and downconversion mixing. All circuit components are integrated into 0.6 mm(2) area and fabricated on 200 mm silicon wafers, showing the unprecedented graphene circuit complexity and silicon complementary metal-oxide-semiconductor process compatibility. The demonstrated circuit performance allow us to use graphene integrated circuit to perform practical wireless communication functions, receiving and restoring digital text transmitted on a 4.3-GHz carrier signal.

  1. Time-domain analysis methodology for large-scale RLC circuits and its applications

    Institute of Scientific and Technical Information of China (English)

    LUO Zuying; CAI Yici; Sheldon X.-D Tan; HONG Xianlong; WANG Xiaoyi; PAN Zhu; FU Jingjing

    2006-01-01

    With soaring work frequency and decreasing feature sizes, VLSI circuits with RLC parasitic components are more like analog circuits and should be carefully analyzed in physical design. However, the number of extracted RLC components is typically too large to be analyzed efficiently by using present analog circuit simulators like SPICE. In order to speedup the simulations without error penalty, this paper proposes a novel methodology to compress the time-descritized circuits resulted from numerical integration approximation at every time step. The main contribution of the methodology is the efficient structure-level compression of DC circuits containing many current sources, which is an important complement to present circuit analysis theory. The methodology consists of the following parts: 1) An approach is proposed to delete all intermediate nodes of RL branches. 2) An efficient approach is proposed to compress and back-solve parallel and serial branches so that it is error-free and of linear complexity to analyze circuits of tree topology. 3) The Y to ( transformation method is used to error-free reduce and back-solve the intermediate nodes of ladder circuits with the linear complexity. Thus, the whole simulation method is very accurate and of linear complexity to analyze circuits of chain topology. Based on the methodology, we propose several novel algorithms for efficiently solving RLC-model transient power/ground (P/G) networks. Among them, EQU-ADI algorithm of linear-complexity is proposed to solve RLC P/G networks with mesh-tree or mesh-chain topologies. Experimental results show that the proposed method is at least two orders of magnitude faster than SPICE while it can scale linearly in both time- and memory-complexity to solve very large P/G networks.

  2. Full wave analysis of non-radiative dielectric waveguide modulator for the determination of electrical equivalent circuit

    Indian Academy of Sciences (India)

    N P Pathak; A Basu; S K Koul

    2008-07-01

    This paper reports the determination of electrical equivalent circuit of ON/OFF modulator in non-radiative dielectric (NRD) guide configurations at Ka-band. Schottky barrier mixer diode is used to realize this modulator and its characteristics are determined experimentally using vector network analyzer. Full wave FEM simulator HFSS is used to determine an equivalent circuit for the mounted diode and modulator in ON and OFF states. This equivalent circuit is used to qualitatively explain the experimental characteristics of modulator.

  3. Combination Approach of FEM and Circuit System in IR Drop Analysis and Its Applications

    Institute of Scientific and Technical Information of China (English)

    TANG Zhanghong; YUAN Jiansheng

    2008-01-01

    A method was developed to solve the combined system of the current field and the circuit. The "super-node" was used to transform the matdx for conventional nodal analyses of a circuit system from non-positive definite to positive definite. Then, a positive definite matdx for the overall system was obtained by combining the matrix from the circuit nodal analysis method and the matrix resulted from finite element method (FEM) formulation to solve the FEM fields. This approach has been successfully applied to simulate the electrical potential and current distributions on each metal layer of printed circuit boards (PCBs) and in-tegrated circuit (IC) packages for a given power supply. The simulation results can then be used to analyze the properties of the PCBs and IC packages such as the port resistances and IR drops. The results can also be used to optimize PCB and IC package designs, such as by adjusting the power/ground distribution networks.

  4. A Current-Mode Common-Mode Feedback Circuit (CMFB) with Rail-to-Rail Operation

    Science.gov (United States)

    Suadet, Apirak; Kasemsuwan, Varakorn

    2011-03-01

    This paper presents a current-mode common-mode feedback (CMFB) circuit with rail-to-rail operation. The CMFB is a stand-alone circuit, which can be connected to any low voltage transconductor without changing or upsetting the existing circuit. The proposed CMFB employs current mirrors, operating as common-mode detector and current amplifier to enhance the loop gain of the CMFB. The circuit employs positive feedback to enhance the output impedance and gain. The circuit has been designed using a 0.18 μm CMOS technology under 1V supply and analyzed using HSPICE with BSIM3V3 device models. A pseudo-differential amplifier using two common sources and the proposed CMFB shows rail to rail output swing (± 0.7 V) with low common-mode gain (-36 dB) and power dissipation of 390 μW.

  5. Hierarchical Stochastic Simulation Algorithm for SBML Models of Genetic Circuits

    OpenAIRE

    Watanabe, Leandro H.; Chris J. Myers

    2014-01-01

    This paper describes a hierarchical stochastic simulation algorithm, which has been implemented within iBioSim, a tool used to model, analyze, and visualize genetic circuits. Many biological analysis tools flatten out hierarchy before simulation, but there are many disadvantages associated with this approach. First, the memory required to represent the model can quickly expand in the process. Second, the flattening process is computationally expensive. Finally, when modeling a dynamic cellula...

  6. Evolution of Quantum State for Mesoscopic Circuits with Dissipation

    Institute of Scientific and Technical Information of China (English)

    WAN Hua-Ming; LUO Hai-Mei; WANG Yi-Fan

    2005-01-01

    Based on the maximum entropy principle, we present a density matrix of mesoscopic RLC circuit to make it possible to analyze the connection of the initial condition with temperature. Our results show that the quantum state evolution is closely related to the initial condition, and that the system evolves to generalized coherent state if it is in ground state initially, and evolves to squeezed state if it is in excited state initially.

  7. Development, integration and testing of automated triggering circuit for hybrid DC circuit breaker

    International Nuclear Information System (INIS)

    A novel concept of Hybrid DC circuit breaker having combination of mechanical switch and static switch provides arc-less current commutation into the dump resistor during quench in superconducting magnet operation. The triggering of mechanical and static switches in Hybrid DC breaker can be automatized which can effectively reduce the overall current commutation time of hybrid DC circuit breaker and make the operation independent of opening time of mechanical switch. With this view, a dedicated control circuit (auto-triggering circuit) has been developed which can decide the timing and pulse duration for mechanical switch as well as static switch from the operating parameters. This circuit has been tested with dummy parameters and thereafter integrated with the actual test set up of hybrid DC circuit breaker. This paper deals with the conceptual design of the auto-triggering circuit, its control logic and operation. The test results of Hybrid DC circuit breaker using this circuit have also been discussed. (author)

  8. Pragmatic circuits signals and filters

    CERN Document Server

    Eccles, William

    2006-01-01

    Pragmatic Circuits: Signals and Filters is built around the processing of signals. Topics include spectra, a short introduction to the Fourier series, design of filters, and the properties of the Fourier transform. The focus is on signals rather than power. But the treatment is still pragmatic. For example, the author accepts the work of Butterworth and uses his results to design filters in a fairly methodical fashion. This third of three volumes finishes with a look at spectra by showing how to get a spectrum even if a signal is not periodic. The Fourier transform provides a way of dealing wi

  9. Circuit considerations for repetitive railguns

    Energy Technology Data Exchange (ETDEWEB)

    Honih, E.M.

    1986-01-01

    Railgun electromagnetic launchers have significant military and scientific potential. They provide direct conversion of electrical energy to projectile kinetic energy, and they offer the hope of achieving projectile velocities greatly exceeding the limits of conventional guns. With over 10 km/sec already demonstrated, railguns are attracting attention for tactical and strategic weapons systems and for scientific equation-of-state research. The full utilization of railguns will require significant improvements in every aspect of system design - projectile, barrel, and power source - to achieve operation on a large scale. This paper will review fundamental aspects of railguns, with emphasis on circuit considerations and repetitive operation.

  10. Advanced Microwave Circuits and Systems

    DEFF Research Database (Denmark)

    is usually optimized to have high output power, high efficiency, optimum heat dissipation and high gain. The third part of this book presents power amplifier designs through a series of design examples. Designs undertaken include a switching mode power amplifier, Doherty power amplifier, and flexible power...... such as voltage-controlled oscillators and electron devices for millimeter wave and submillimeter wave applications. This part also covers studies of integrated buffer circuits. Passive components are indispensable elements of any electronic system. The increasing demands to miniaturization and cost effectiveness...

  11. HF radio systems and circuits

    CERN Document Server

    Sabin, William

    1998-01-01

    A comprehensive reference for the design of high frequency communications systems and equipment. This revised edition is loaded with practical data, much of which cannot be found in other reference books. Its approach to the subject follows the needs of an engineer from system definition and performance requirements down to the individual circuit elements that make up radio transmitters and receivers. The accompanying disk contains updated software on filters, matching networks and receiver analysis. SciTech Publishing also provides many other products related to Communication Systems Design.

  12. Radio frequency integrated circuit design

    CERN Document Server

    Rogers, John W M

    2010-01-01

    This newly revised and expanded edition of the 2003 Artech House classic, Radio Frequency Integrated Circuit Design, serves as an up-to-date, practical reference for complete RFIC know-how. The second edition includes numerous updates, including greater coverage of CMOS PA design, RFIC design with on-chip components, and more worked examples with simulation results. By emphasizing working designs, this book practically transports you into the authors' own RFIC lab so you can fully understand the function of each design detailed in this book. Among the RFIC designs examined are RF integrated LC

  13. Circuit for Driving Piezoelectric Transducers

    Science.gov (United States)

    Randall, David P.; Chapsky, Jacob

    2009-01-01

    The figure schematically depicts an oscillator circuit for driving a piezoelectric transducer to excite vibrations in a mechanical structure. The circuit was designed and built to satisfy application-specific requirements to drive a selected one of 16 such transducers at a regulated amplitude and frequency chosen to optimize the amount of work performed by the transducer and to compensate for both (1) temporal variations of the resonance frequency and damping time of each transducer and (2) initially unknown differences among the resonance frequencies and damping times of different transducers. In other words, the circuit is designed to adjust itself to optimize the performance of whichever transducer is selected at any given time. The basic design concept may be adaptable to other applications that involve the use of piezoelectric transducers in ultrasonic cleaners and other apparatuses in which high-frequency mechanical drives are utilized. This circuit includes three resistor-capacitor networks that, together with the selected piezoelectric transducer, constitute a band-pass filter having a peak response at a frequency of about 2 kHz, which is approximately the resonance frequency of the piezoelectric transducers. Gain for generating oscillations is provided by a power hybrid operational amplifier (U1). A junction field-effect transistor (Q1) in combination with a resistor (R4) is used as a voltage-variable resistor to control the magnitude of the oscillation. The voltage-variable resistor is part of a feedback control loop: Part of the output of the oscillator is rectified and filtered for use as a slow negative feedback to the gate of Q1 to keep the output amplitude constant. The response of this control loop is much slower than 2 kHz and, therefore, does not introduce significant distortion of the oscillator output, which is a fairly clean sine wave. The positive AC feedback needed to sustain oscillations is derived from sampling the current through the

  14. Model reduction for circuit simulation

    CERN Document Server

    Hinze, Michael; Maten, E Jan W Ter

    2011-01-01

    Simulation based on mathematical models plays a major role in computer aided design of integrated circuits (ICs). Decreasing structure sizes, increasing packing densities and driving frequencies require the use of refined mathematical models, and to take into account secondary, parasitic effects. This leads to very high dimensional problems which nowadays require simulation times too large for the short time-to-market demands in industry. Modern Model Order Reduction (MOR) techniques present a way out of this dilemma in providing surrogate models which keep the main characteristics of the devi

  15. The interface design for the USB-based multi-channel analyzer

    CERN Document Server

    Sun Guang Cai

    2002-01-01

    A new style interface circuit design for multi-channel analyzer is introduced, which takes the advantages of Universal Serial Bus to communicate with computer and gets the merit of high universality and Plug and Play. The interface circuit also uses dual-port SRAM and high-speed MCU to store and translate data, which could solve the bottleneck problem existing in data translation from the interface to computer

  16. Ferroelectric Field-Effect Transistor Differential Amplifier Circuit Analysis

    Science.gov (United States)

    Phillips, Thomas A.; MacLeod, Todd C.; Ho, Fat D.

    2008-01-01

    There has been considerable research investigating the Ferroelectric Field-Effect Transistor (FeFET) in memory circuits. However, very little research has been performed in applying the FeFET to analog circuits. This paper investigates the use of FeFETs in a common analog circuit, the differential amplifier. The two input Metal-Oxide-Semiconductor (MOS) transistors in a general MOS differential amplifier circuit are replaced with FeFETs. Resistors are used in place of the other three MOS transistors. The FeFET model used in the analysis has been previously reported and was based on experimental device data. Because of the FeFET hysteresis, the FeFET differential amplifier has four different operating modes depending on whether the FeFETs are positively or negatively polarized. The FeFET differential amplifier operation in the different modes was analyzed by calculating the amplifier voltage transfer and gain characteristics shown in figures 2 through 5. Comparisons were made between the FeFET differential amplifier and the standard MOS differential amplifier. Possible applications and benefits of the FeFET differential amplifier are discussed.

  17. Dynamical properties of electrical circuits with fully nonlinear memristors

    CERN Document Server

    Riaza, Ricardo

    2010-01-01

    The recent design of a nanoscale device with a memristive characteristic has had a great impact in nonlinear circuit theory. Such a device, whose existence was predicted by Leon Chua in 1971, is governed by a charge-dependent voltage-current relation of the form $v=M(q)i$. In this paper we show that allowing for a fully nonlinear characteristic $v=\\eta(q, i)$ in memristive devices provides a general framework for modeling and analyzing a very broad family of electrical and electronic circuits; Chua's memristors are particular instances in which $\\eta(q,i)$ is linear in $i$. We examine several dynamical features of circuits with fully nonlinear memristors, accommodating not only charge-controlled but also flux-controlled ones, with a characteristic of the form $i=\\zeta(\\varphi, v)$. Our results apply in particular to Chua's memristive circuits; certain properties of these can be seen as a consequence of the special form of the elastance and reluctance matrices displayed by Chua's memristors.

  18. Structure-Based Deadlock Checking of Asynchronous Circuits

    Institute of Scientific and Technical Information of China (English)

    Hong-Guang Ren; Zhi-Ying Wang; Doug Edwards

    2011-01-01

    It is important to verify the absence of deadlocks in asynchronous circuits.Much previous work relies on a reachability analysis of the circuits' states,with the use of binary decision diagrams (BDDs) or Petri nets to model the behaviors of circuits.This paper presents an alternative approach focusing on the structural properties of well-formed asynchronous circuits that will never suffer deadlocks.A class of data-driven asynchronous pipelines is targeted in this paper,which can be viewed as a network of basic components connected by handshake channels.The sufficient and necessary conditions for a component network consisting of Steer,Merge,Fork and Join are given.The slack elasticity of the channels is analyzed in order to introduce pipelining.As an application,a deadlock checking method is implemented in a syntax-directed asynchronous design tool - Teak.The proposed method shows a great runtime advantage when compared against previous Petri net based verification tools.

  19. A Singularity in the Kirchhoff's Circuit Equations

    CERN Document Server

    Harsha, N R Sree

    2016-01-01

    Students often have difficulty in understanding qualitatively the behaviour of simple electric circuits. In particular, as different studies have shown, they find multiple batteries connected in multiple loops difficult to analyse. In a recent paper [Phys. Educ. 50 568 (2015)], we showed such an electric circuit, which consists of ideal batteries connected in parallel, that couldn't be solved by the existing circuit analysis methods. In this paper, we shall introduce a new mathematical method of solving simple electric circuits from the solutions of more general circuits and show that the currents, in this particular circuit, take the indeterminate 0/0 form. We shall also present some of the implications of teaching the method. We believe that the description presented in this paper should help the instructors in teaching the behaviour of multiple batteries connected in parallel.

  20. Physical synthesis of quantum circuits using templates

    Science.gov (United States)

    Mirkhani, Zahra; Mohammadzadeh, Naser

    2016-06-01

    Similar to traditional CMOS circuits, quantum circuit design flow is divided into two main processes: logic synthesis and physical design. Addressing the limitations imposed on optimization of the quantum circuit metrics because of no information sharing between logic synthesis and physical design processes, the concept of "physical synthesis" was introduced for quantum circuit flow, and a few techniques were proposed for it. Following that concept, in this paper a new approach for physical synthesis inspired by template matching idea in quantum logic synthesis is proposed to improve the latency of quantum circuits. Experiments show that by using template matching as a physical synthesis approach, the latency of quantum circuits can be improved by more than 23.55 % on average.

  1. Physical synthesis of quantum circuits using templates

    Science.gov (United States)

    Mirkhani, Zahra; Mohammadzadeh, Naser

    2016-10-01

    Similar to traditional CMOS circuits, quantum circuit design flow is divided into two main processes: logic synthesis and physical design. Addressing the limitations imposed on optimization of the quantum circuit metrics because of no information sharing between logic synthesis and physical design processes, the concept of " physical synthesis" was introduced for quantum circuit flow, and a few techniques were proposed for it. Following that concept, in this paper a new approach for physical synthesis inspired by template matching idea in quantum logic synthesis is proposed to improve the latency of quantum circuits. Experiments show that by using template matching as a physical synthesis approach, the latency of quantum circuits can be improved by more than 23.55 % on average.

  2. Design of a New Chaos Circuit and Its Encryption to Digital Information

    Institute of Scientific and Technical Information of China (English)

    WANG Hong; PENG Jian-hua; ZHOU Zhen-gou

    2004-01-01

    A new hyperchaos circuit system with simple structure is designed in this paper. It can be implemented with changeable dimensions 3, 5, 7, 9, etc, therefore it can afford different security grades for applications. The dynamic characters of the 7th order circuit have been analyzed as an example. Using the hyperchaos time sequence produced by this circuit as key sequence, the encryption and decryption to digital signals of text and image files have been realized, and the real-time ability has been increased with encrypting digital signals per byte.

  3. Analyzing Valuation Practices through Contracts

    DEFF Research Database (Denmark)

    Tesnière, Germain; Labatut, Julie; Boxenbaum, Eva

    This paper seeks to analyze the most recent changes in how societies value animals. We analyze this topic through the prism of contracts between breeding companies and farmers. Focusing on new valuation practices and qualification of breeding animals, we question the evaluation of difficult...... commensurable entities (animal, embryo, mating) and the impacts of these valuation and qualifications on government of living entities....

  4. Analyzing data files in SWAN

    CERN Document Server

    Gajam, Niharika

    2016-01-01

    Traditionally analyzing data happens via batch-processing and interactive work on the terminal. The project aims to provide another way of analyzing data files: A cloud-based approach. It aims to make it a productive and interactive environment through the combination of FCC and SWAN software.

  5. A Survey of Memristive Threshold Logic Circuits

    OpenAIRE

    Maan, Akshay Kumar; Jayadevi, Deepthi Anirudhan; James, Alex Pappachen

    2016-01-01

    In this paper, we review the different memristive threshold logic (MTL) circuits that are inspired from the synaptic action of flow of neurotransmitters in the biological brain. Brain like generalisation ability and area minimisation of these threshold logic circuits aim towards crossing the Moores law boundaries at device, circuits and systems levels.Fast switching memory, signal processing, control systems, programmable logic, image processing, reconfigurable computing, and pattern recognit...

  6. Monitoring transients in low inductance circuits

    Science.gov (United States)

    Guilford, R.P.; Rosborough, J.R.

    1985-10-21

    The instant invention relates to methods of and apparatus for monitoring transients in low inductance circuits and to a probe utilized to practice said method and apparatus. More particularly, the instant invention relates to methods of and apparatus for monitoring low inductance circuits, wherein the low inductance circuits include a pair of flat cable transmission lines. The instant invention is further directed to a probe for use in monitoring pairs of flat cable transmission lines.

  7. Theory of circuit block switch-off

    OpenAIRE

    S. Henzler; J. Berthold; G. Georgakos; Schmitt-Landsiedel, D.

    2005-01-01

    Switching-off unused circuit blocks is a promising approach to supress static leakage currents in ultra deep sub-micron CMOS digital systems. Basic performance parameters of Circuit Block Switch-Off (CBSO) schemes are defined and their dependence on basic circuit parameters is estimated. Therefore the design trade-off between strong leakage suppression in idle mode and adequate dynamic performance in active mode can be supported by simple analytic investigations. Additionally, a guideline for...

  8. Single-Phase Full-Wave Rectifier as an Effective Example to Teach Normalization, Conduction Modes, and Circuit Analysis Methods

    Directory of Open Access Journals (Sweden)

    Predrag Pejovic

    2013-12-01

    Full Text Available Application of a single phase rectifier as an example in teaching circuit modeling, normalization, operating modes of nonlinear circuits, and circuit analysis methods is proposed.The rectifier supplied from a voltage source by an inductive impedance is analyzed in the discontinuous as well as in the continuous conduction mode. Completely analytical solution for the continuous conduction mode is derived. Appropriate numerical methods are proposed to obtain the circuit waveforms in both of the operating modes, and to compute the performance parameters. Source code of the program that performs such computation is provided.

  9. IMPROVED VIRTUAL CIRCUIT ROUTING ALGORITHM FOR WIRELESS SENSOR NETWORKS UNDER THE ASPECT OF POWER AWARENESS

    OpenAIRE

    Abid Ali Minhas; Thomas Trathnigg; Christian Steger; Reinhold Weiß

    2006-01-01

    Routing algorithms have shown their importance in the power aware wireless micro-sensor networks. In this paper first we present virtual circuit algorithm (VCRA), a routing algorithm for wireless sensor networks. We analyze the power utilized by nodes to lengthen the battery life and thus improving the lifetime of wireless sensor network. We discuss VCRA in comparison with the Multihoprouter, an algorithm developed by UC Berkeley. Then we present Improved Virtual Circuit Routing Algorithm (IV...

  10. Short-Circuit Calculation in Distribution Networks with Distributed Induction Generators

    OpenAIRE

    Niancheng Zhou; Fan Ye; Qianggang Wang; Xiaoxuan Lou; Yuxiang Zhang

    2016-01-01

    This paper presents an improved current source equivalent model method to determine the short-circuit current of a distribution system with multiple fixed-speed and variable-speed induction generators (IGs). The correlation coefficients of flux components between stator and rotor under the unsymmetrical fault are analyzed using the positive and negative sequence steady-state equivalent circuits of an IG. The terminal voltage and current responses of fixed-speed and variable-speed IGs with and...

  11. Implications of Electronics Constraints for Solid-State Quantum Error Correction and Quantum Circuit Failure Probability

    OpenAIRE

    Levy, James E.; Carroll, Malcolm S.; Ganti, Anand; Phillips, Cynthia A.; Landahl, Andrew J.; Gurrieri, Thomas M.; Carr, Robert D.; Stalford, Harold L.; Nielsen, Erik

    2011-01-01

    In this paper we present the impact of classical electronics constraints on a solid-state quantum dot logical qubit architecture. Constraints due to routing density, bandwidth allocation, signal timing, and thermally aware placement of classical supporting electronics significantly affect the quantum error correction circuit's error rate. We analyze one level of a quantum error correction circuit using nine data qubits in a Bacon-Shor code configured as a quantum memory. A hypothetical silico...

  12. Analog circuit design art, science, and personalities

    CERN Document Server

    Williams, Jim

    1991-01-01

    Analog Circuit Design: Art, Science, and Personalities discusses the many approaches and styles in the practice of analog circuit design. The book is written in an informal yet informative manner, making it easily understandable to those new in the field. The selection covers the definition, history, current practice, and future direction of analog design; the practice proper; and the styles in analog circuit design. The book also includes the problems usually encountered in analog circuit design; approach to feedback loop design; and other different techniques and applications. The text is

  13. Electric circuit theory applied electricity and electronics

    CERN Document Server

    Yorke, R

    1981-01-01

    Electric Circuit Theory provides a concise coverage of the framework of electrical engineering. Comprised of six chapters, this book emphasizes the physical process of electrical engineering rather than abstract mathematics. Chapter 1 deals with files, circuits, and parameters, while Chapter 2 covers the natural and forced response of simple circuit. Chapter 3 talks about the sinusoidal steady state, and Chapter 4 discusses the circuit analysis. The fifth chapter tackles frequency response of networks, and the last chapter covers polyphase systems. This book will be of great help to electrical

  14. Wafer-scale graphene integrated circuit.

    Science.gov (United States)

    Lin, Yu-Ming; Valdes-Garcia, Alberto; Han, Shu-Jen; Farmer, Damon B; Meric, Inanc; Sun, Yanning; Wu, Yanqing; Dimitrakopoulos, Christos; Grill, Alfred; Avouris, Phaedon; Jenkins, Keith A

    2011-06-10

    A wafer-scale graphene circuit was demonstrated in which all circuit components, including graphene field-effect transistor and inductors, were monolithically integrated on a single silicon carbide wafer. The integrated circuit operates as a broadband radio-frequency mixer at frequencies up to 10 gigahertz. These graphene circuits exhibit outstanding thermal stability with little reduction in performance (less than 1 decibel) between 300 and 400 kelvin. These results open up possibilities of achieving practical graphene technology with more complex functionality and performance.

  15. Hyperchaotic circuit with damped harmonic oscillators

    DEFF Research Database (Denmark)

    Lindberg, Erik; Murali, K.; Tamasevicius, A.

    2001-01-01

    A simple fourth-order hyperchaotic circuit with damped harmonic oscillators is described. ANP3 and PSpice simulations including an eigenvalue study of the linearized Jacobian are presented together with a hardware implementation. The circuit contains two inductors with series resistance, two ideal...... capacitors and one nonlinear active conductor. The Lyapunov exponents are presented to confirm the hyperchaotic nature of the oscillations of the circuit. The nonlinear conductor is realized with a diode. A negative impedance converter and a linear resistor. The performance of the circuit is investigated...... by means of numerical integration of the appropriate differential equations....

  16. A Survey of Fast Analog Circuit Analysis Algorithm using SPICE

    OpenAIRE

    T.Murugajothi

    2014-01-01

    is paper presents a fast analog circuit analysis algorithm, fundamental circuit-based circuit analysis, for circuits being repeatedly modified and verified in product development. The algorithm reuses previous circuit simulation result on successive changed circuit analysis to achieve simulation operation reduction. The algorithm is implemented with SPICE simulator on linear and nonlinear circuit applications with the proposed device delta models. The experiments show that t...

  17. Nuclear fuel microsphere gamma analyzer

    Science.gov (United States)

    Valentine, Kenneth H.; Long, Jr., Ernest L.; Willey, Melvin G.

    1977-01-01

    A gamma analyzer system is provided for the analysis of nuclear fuel microspheres and other radioactive particles. The system consists of an analysis turntable with means for loading, in sequence, a plurality of stations within the turntable; a gamma ray detector for determining the spectrum of a sample in one section; means for analyzing the spectrum; and a receiver turntable to collect the analyzed material in stations according to the spectrum analysis. Accordingly, particles may be sorted according to their quality; e.g., fuel particles with fractured coatings may be separated from those that are not fractured, or according to other properties.

  18. Activity-dependent modulation of neural circuit synaptic connectivity

    Directory of Open Access Journals (Sweden)

    Charles R Tessier

    2009-07-01

    Full Text Available In many nervous systems, the establishment of neural circuits is known to proceed via a two-stage process; 1 early, activity-independent wiring to produce a rough map characterized by excessive synaptic connections, and 2 subsequent, use-dependent pruning to eliminate inappropriate connections and reinforce maintained synapses. In invertebrates, however, evidence of the activity-dependent phase of synaptic refinement has been elusive, and the dogma has long been that invertebrate circuits are “hard-wired” in a purely activity-independent manner. This conclusion has been challenged recently through the use of new transgenic tools employed in the powerful Drosophila system, which have allowed unprecedented temporal control and single neuron imaging resolution. These recent studies reveal that activity-dependent mechanisms are indeed required to refine circuit maps in Drosophila during precise, restricted windows of late-phase development. Such mechanisms of circuit refinement may be key to understanding a number of human neurological diseases, including developmental disorders such as Fragile X syndrome (FXS and autism, which are hypothesized to result from defects in synaptic connectivity and activity-dependent circuit function. This review focuses on our current understanding of activity-dependent synaptic connectivity in Drosophila, primarily through analyzing the role of the fragile X mental retardation protein (FMRP in the Drosophila FXS disease model. The particular emphasis of this review is on the expanding array of new genetically-encoded tools that are allowing cellular events and molecular players to be dissected with ever greater precision and detail.

  19. Ion chromatography in the manufacture of multilayer circuit boards

    Science.gov (United States)

    Smith, Robert E.

    1990-01-01

    Ion chromatography (IC) has proven useful in analyzing chemical solutions used in the manufacture of multilayer circuit boards. Unlike other chemical quantification techniques, IC provides results on ions not expected in the production solutions. Thus, solution contamination and break-down products can be monitored in every phase of the circuit board manufacturing. During the first phase, epoxy laminates experience an etchback, first in chromic acid, which can be analyzed for trace chloride and sulfate, then in ammonium bifluoride/HCl, which can be analyzed for fluoride and chloride. Following a wet-blasting to roughen up the surface, 20 microinches of copper are deposited using an electroless bath. Again, IC is applicable for monitoring formate, tartarate, and sulfate levels. Next, an acid copper bath is used to electroplate the through holes with 0.001 inches of ductile copper. This bath is analyzed for trace chloride. Photoimaging is then performed, and the organic solvents used can be assayed for trace ionic chloride. Finally, a fluoroboric acid-based tin-lead bath is used to deposit a solderable alloy. This bath is analyzed for fluoroborate, tin, and lead. In addition, mobile phase ion chromatography (MPIC) is used to monitor the nonionic organic brighteners in the baths.

  20. Short-Circuit Withstand Current Rating for Low Voltage Switchgear : Short-Circuit Current Rating (SCCR)

    OpenAIRE

    Schütt, Matthias

    2016-01-01

    The subject of this thesis was to observe the short-circuit currents at electrical distribution boards. The purpose was to investigate different methods of protecting switchgears from dam-ages caused by short-circuit currents. Manufactures of switchgears need to indicate the rated short-circuit withstand current of their assembly. This thesis is presenting methods of defining the right value of the short-circuit withstand current. This thesis presents theoretical information about the cau...

  1. Towards programmable plant genetic circuits.

    Science.gov (United States)

    Medford, June I; Prasad, Ashok

    2016-07-01

    Synthetic biology enables the construction of genetic circuits with predictable gene functions in plants. Detailed quantitative descriptions of the transfer function or input-output function for genetic parts (promoters, 5' and 3' untranslated regions, etc.) are collected. These data are then used in computational simulations to determine their robustness and desired properties, thereby enabling the best components to be selected for experimental testing in plants. In addition, the process forms an iterative workflow which allows vast improvement to validated elements with sub-optimal function. These processes enable computational functions such as digital logic in living plants and follow the pathway of technological advances which took us from vacuum tubes to cell phones. PMID:27297052

  2. Beta-gamma discriminator circuit

    International Nuclear Information System (INIS)

    The major difficulty encountered in the determination of beta-ray dose in field conditions is generally the presence of a relatively high gamma-ray component. Conventional dosimetry instruments use a shield on the detector to estimate the gamma-ray component in comparison with the beta-ray component. More accurate dosimetry information can be obtained from the measured beta spectrum itself. At Los Alamos, a detector and discriminator circuit suitable for use in a portable spectrometer have been developed. This instrument will discriminate between gammas and betas in a mixed field. The portable package includes a 256-channel MCA which can be programmed to give a variety of outputs, including a spectral display, and may be programmed to read dose directly

  3. Electrical circuit theory and technology

    CERN Document Server

    Bird, John

    2014-01-01

    This much-loved textbook explains the principles of electrical circuit theory and technology so that students of electrical and mechanical engineering can master the subject. Real-world situations and engineering examples put the theory into context. The inclusion of worked problems with solutions help you to learn and further problems then allow you to test and confirm you have fully understood each subject. In total the book contains 800 worked problems, 1000 further problems and 14 revision tests with answers online. This an ideal text for foundation and undergraduate degree students and those on upper level vocational engineering courses, in particular electrical and mechanical. It provides a sound understanding of the knowledge required by technicians in fields such as electrical engineering, electronics and telecommunications. This edition has been updated with developments in key areas such as semiconductors, transistors, and fuel cells, along with brand new material on ABCD parameters and Fourier's An...

  4. Integrated Circuit Electromagnetic Immunity Handbook

    Science.gov (United States)

    Sketoe, J. G.

    2000-08-01

    This handbook presents the results of the Boeing Company effort for NASA under contract NAS8-98217. Immunity level data for certain integrated circuit parts are discussed herein, along with analytical techniques for applying the data to electronics systems. This handbook is built heavily on the one produced in the seventies by McDonnell Douglas Astronautics Company (MDAC, MDC Report E1929 of 1 August 1978, entitled Integrated Circuit Electromagnetic Susceptibility Handbook, known commonly as the ICES Handbook, which has served countless systems designers for over 20 years). Sections 2 and 3 supplement the device susceptibility data presented in section 4 by presenting information on related material required to use the IC susceptibility information. Section 2 concerns itself with electromagnetic susceptibility analysis and serves as a guide in using the information contained in the rest of the handbook. A suggested system hardening requirements is presented in this chapter. Section 3 briefly discusses coupling and shielding considerations. For conservatism and simplicity, a worst case approach is advocated to determine the maximum amount of RF power picked up from a given field. This handbook expands the scope of the immunity data in this Handbook is to of 10 MHz to 10 GHz. However, the analytical techniques provided are applicable to much higher frequencies as well. It is expected however, that the upper frequency limit of concern is near 10 GHz. This is due to two factors; the pickup of microwave energy on system cables and wiring falls off as the square of the wavelength, and component response falls off at a rapid rate due to the effects of parasitic shunt paths for the RF energy. It should be noted also that the pickup on wires and cables does not approach infinity as the frequency decreases (as would be expected by extrapolating the square law dependence of the high frequency roll-off to lower frequencies) but levels off due to mismatch effects.

  5. Oxygen analyzers: failure rates and life spans of galvanic cells.

    Science.gov (United States)

    Meyer, R M

    1990-07-01

    Competing technologies exist for measuring oxygen concentrations in breathing circuits. Over a 4-year period, two types of oxygen analyzers were studied prospectively in routine clinical use to determine the incidence and nature of malfunctions. Newer AC-powered galvanic analyzers (North American Dräger O2med) were compared with older, battery-powered polarographic analyzers (Ohmeda 201) by recording all failures and necessary repairs. The AC-powered galvanic analyzer had a significantly lower incidence of failures (0.12 +/- 0.04 failures per machine-month) than the battery-powered polarographic analyzer (4.0 +/- 0.3 failures per machine-month). Disposable capsules containing the active galvanic cells lasted 12 +/- 7 months. Although the galvanic analyzers tended to remain out of service longer, awaiting the arrival of costly parts, the polarographic analyzers were more expensive to keep operating when calculations included the cost of time spent on repairs. Stocking galvanic capsules would have decreased the amount of time the galvanic analyzers were out of service, while increasing costs. In conclusion, galvanic oxygen analyzers appear capable of delivering more reliable service at a lower overall cost. By keeping the galvanic capsules exposed to room air during periods of storage, it should be possible to prolong their life span, further decreasing the cost of using them. In addition, recognizing the aberrations in their performance that warn of the exhaustion of the galvanic cells should permit timely recording and minimize downtime.

  6. Development of a miniature permanent magnetic circuit for nuclear magnetic resonance chip

    Science.gov (United States)

    Lu, Rongsheng; Yi, Hong; Wu, Weiping; Ni, Zhonghua

    2013-07-01

    The existing researches of miniature magnetic circuits focus on the single-sided permanent magnetic circuits and the Halbach permanent magnetic circuits. In the single-sided permanent magnetic circuits, the magnetic flux density is always very low in the work region. In the Halbach permanent magnetic circuits, there are always great difficulties in the manufacturing and assembly process. The static magnetic flux density required for nuclear magnetic resonance(NMR) chip is analyzed based on the signal noise ratio(SNR) calculation model, and then a miniature C-shaped permanent magnetic circuit is designed as the required magnetic flux density. Based on Kirchhoff's law and magnetic flux refraction principle, the concept of a single shimming ring is proposed to improve the performance of the designed magnetic circuit. Using the finite element method, a comparative calculation is conducted. The calculation results demonstrate that the magnetic circuit improved with a single shimming has higher magnetic flux density and better magnetic field homogeneity than the one improved with no shimming ring or double shimming rings. The proposed magnetic circuit is manufactured and its experimental test platform is also built. The magnetic flux density measured in the work region is 0.7 T, which is well coincided with the theoretical design. The spatial variation of the magnetic field is within the range of the instrument error. At last, the temperature dependence of the magnetic flux density produced by the proposed magnetic circuit is investigated through both theoretical analysis and experimental study, and a linear functional model is obtained. The proposed research is crucial for solving the problem in the application of NMR-chip under different environmental temperatures.

  7. A Low-Noise Readout Circuit for Gyroscopes

    Institute of Scientific and Technical Information of China (English)

    Guanshi Wang; Xiaowei Liu; Changchun Dong

    2015-01-01

    In order to suppress the noise of gyroscopes, the method based on lock⁃in amplifier and capacitor matching of the low⁃noise readout circuit is proposed. Firstly, the principle to suppress the noise by lock⁃in amplifier is analyzed, and the noise model of front end is proposed. Secondly, the noise optimization for the charge amplifier is presented according to the noise model of front end. Finally, a readout circuit is constructed by this approach. The measurement results show that the parasitic capacitance of front end is 18 pF, and the noise at resonant frequency ( 4 kHz) is 133 nV/Hz1/2 , and the overall bias stability is 30°/h, and the noise level is 0�003°/( s·Hz1/2 ) . The noise of the gyroscope with the low⁃noise readout by this method is suppressed effectively.

  8. Entangling distant resonant exchange qubits via circuit quantum electrodynamics

    Science.gov (United States)

    Srinivasa, Vanita; Taylor, Jacob M.; Tahan, Charles

    Enabling modularity within a quantum information processing device relies on robust entanglement of coherent qubits at macroscopic distances. To address this challenge, we investigate theoretically a hybrid quantum system consisting of spatially separated resonant exchange qubits, defined in three-electron semiconductor triple quantum dots, that are coupled via a superconducting transmission line resonator. By analyzing three specific approaches drawn from circuit quantum electrodynamics and Hartmann-Hahn double resonance techniques for implementing resonator-mediated two-qubit entangling gates in both dispersive and resonant regimes, we show that methods for entangling superconducting qubits map directly to resonant exchange qubits. We also calculate the rate of relaxation via phonons for resonant exchange qubits in silicon triple dots and show that such an implementation is particularly well-suited to achieving the strong coupling regime. Our approach combines the robustness of encoded spin qubits in silicon with the rapid and robust long-range entanglement provided by circuit QED systems.

  9. Analysis of circuits including magnetic cores (MTRAC)

    Science.gov (United States)

    Hanzen, G. R.; Nitzan, D.; Herndon, J. R.

    1972-01-01

    Development of automated circuit analysis computer program to provide transient analysis of circuits with magnetic cores is discussed. Allowance is made for complications caused by nonlinearity of switching core model and magnetic coupling among loop currents. Computer program is conducted on Univac 1108 computer using FORTRAN IV.

  10. Circuits in the Sun: Solar Panel Physics

    Science.gov (United States)

    Gfroerer, Tim

    2013-01-01

    Typical commercial solar panels consist of approximately 60 individual photovoltaic cells connected in series. Since the usual Kirchhoff rules apply, the current is uniform throughout the circuit, while the electric potential of the individual devices is cumulative. Hence, a solar panel is a good analog of a simple resistive series circuit, except…

  11. Sustainability issues in circuit board recycling

    DEFF Research Database (Denmark)

    Legarth, Jens Brøbech; Alting, Leo; Baldo, Gian Luca

    1995-01-01

    The resource recovery and environmental impact issues of printed circuit board recycling by secondary copper smelters are discussed. Guidelines concerning material selection for circuit board manufacture and concerning the recycling processes are given to enhance recovery efficiency and to lower...... the impacts on the external environment from recycling...

  12. CMOS circuits for analog signal processing

    NARCIS (Netherlands)

    Wallinga, Hans

    1988-01-01

    Design choices in CMOS analog signal processing circuits are presented. Special attention is focussed on continuous-time filter technologies. The basics of MOSFET-C continuous-time filters and CMOS Square Law Circuits are explained at the hand of a graphical MOST characteristics representation.

  13. Water quality control program in experimental circuits

    International Nuclear Information System (INIS)

    The Water Quality Control Program of the Experimental Circuits visualizes studying the water chemistry of the cooling in the primary and secondary circuits, monitoring the corrosion of the systems and studying the mechanism of the corrosion products transport in the systems. (author)

  14. POWER MOS FET MODELS FOR "SWITCHING" CIRCUITS

    OpenAIRE

    Rossel, P; Maimouni, R.; Belabadia, M.; Tranduc, Henri; Cordonnier, C.; Bairanzade, M.

    1988-01-01

    A compact model of the Power VDMOS Transistor compatible with the circuit simulator "SPICE2" is described in this article. This model is applied to the simulation of switching circuit with resistive and inductive loads ; comparisons with experimental results are presented.

  15. Memristive circuits simulate memcapacitors and meminductors

    CERN Document Server

    Pershin, Yuriy V

    2009-01-01

    We suggest electronic circuits with memristors (resistors with memory) that operate as memcapacitors (capacitors with memory) and meminductors (inductors with memory). Using a memristor emulator, the suggested circuits have been built and their operation has been demonstrated, showing a useful and interesting connection between the three memory elements.

  16. Automatic Test Pattern Generation for Digital Circuits

    Directory of Open Access Journals (Sweden)

    S. Hemalatha

    2014-04-01

    Full Text Available Digital circuits complexity and density are increasing and at the same time it should have more quality and reliability. It leads with high test costs and makes the validation more complex. The main aim is to develop a complete behavioral fault simulation and automatic test pattern generation (ATPG system for digital circuits modeled in verilog and VHDL. An integrated Automatic Test Generation (ATG and Automatic Test Executing/Equipment (ATE system for complex boards is developed here. An approach to use memristors (resistors with memory in programmable analog circuits. The Main idea consists in a circuit design in which low voltages are applied to memristors during their operation as analog circuit elements and high voltages are used to program the memristor’s states. This way, as it was demonstrated in recent experiments, the state of memristors does not essentially change during analog mode operation. As an example of our approach, we have built several programmable analog circuits demonstrating memristor -based programming of threshold, gain and frequency. In these circuits the role of memristor is played by a memristor emulator developed by us. A multiplexer is developed to generate a class of minimum transition sequences. The entire hardware is realized as digital logical circuits and the test results are simulated in Model sim software. The results of this research show that behavioral fault simulation will remain as a highly attractive alternative for the future generation of VLSI and system-on-chips (SoC.

  17. Verifying Relay Circuits using State Machines

    NARCIS (Netherlands)

    Eijk, P.H.J. van

    2008-01-01

    In this paper we present, illustrate and discuss a number of techniques that can be used in the modelling and verification of electro-mechanical relay circuits. These techniques are based on state machine descriptions of circuits and their functions, and on applying validation tools for properties o

  18. Automatic design of digital synthetic gene circuits.

    Directory of Open Access Journals (Sweden)

    Mario A Marchisio

    2011-02-01

    Full Text Available De novo computational design of synthetic gene circuits that achieve well-defined target functions is a hard task. Existing, brute-force approaches run optimization algorithms on the structure and on the kinetic parameter values of the network. However, more direct rational methods for automatic circuit design are lacking. Focusing on digital synthetic gene circuits, we developed a methodology and a corresponding tool for in silico automatic design. For a given truth table that specifies a circuit's input-output relations, our algorithm generates and ranks several possible circuit schemes without the need for any optimization. Logic behavior is reproduced by the action of regulatory factors and chemicals on the promoters and on the ribosome binding sites of biological Boolean gates. Simulations of circuits with up to four inputs show a faithful and unequivocal truth table representation, even under parametric perturbations and stochastic noise. A comparison with already implemented circuits, in addition, reveals the potential for simpler designs with the same function. Therefore, we expect the method to help both in devising new circuits and in simplifying existing solutions.

  19. IMPORTANT NOTICE: Cancellation of shuttle Circuit 3

    CERN Multimedia

    2013-01-01

    Circuit 3 of the CERN Shuttle Service (Point 5), which has served CMS since the start of LS1, will be cancelled with effect from Tuesday 16 April. This decision has been taken in consultation with CMS, as the circuit was seldom used.   In response to increasing demand for Circuit 1 - Meyrin and feedback from passengers, the two Circuit 3 journeys will be switched to Circuit 1 – Meyrin (see new timetable below): Mornings: Four journeys instead of three. Circuit 1 now starts at 8:10 (instead of 8:19 a.m.) and runs until 9:27 a.m. (instead of 9:16 a.m.). Lunchtimes: Five journeys in place between 12:10 p.m. and 1:47 p.m. Evenings: Circuit starts at 5:23 p.m. (instead of 5:03 p.m.) and ends at 6:20 p.m. at Building 33. Please note that the circuit will depart from Building 13 instead of Building 33.  

  20. 46 CFR 169.670 - Circuit breakers.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Circuit breakers. 169.670 Section 169.670 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Machinery and... for— (a) Inverse time delay; (b) Instantaneous short circuit protection; and (c) Repeated opening...

  1. Active components for integrated plasmonic circuits

    DEFF Research Database (Denmark)

    Krasavin, A.V.; Bolger, P.M.; Zayats, A.V.;

    2009-01-01

    We present a comprehensive study of highly efficient and compact passive and active components for integrated plasmonic circuit based on dielectric-loaded surface plasmon polariton waveguides.......We present a comprehensive study of highly efficient and compact passive and active components for integrated plasmonic circuit based on dielectric-loaded surface plasmon polariton waveguides....

  2. F-Paris: integrated electronic circuits [Tender

    CERN Multimedia

    2003-01-01

    "Fourniture, montage et tests des circuits imprimes et modules multi composants pour le trajectographe central de CMS. Maximum de 12 000 circuits imprimes et modules multi-composants necessaires au trajectographe central de l'experience CMS aupres du Large Hadron Collider" (1 page).

  3. Post irradiation effects (PIE) in integrated circuits

    International Nuclear Information System (INIS)

    Post Irradiation Effects (PIE) ranging from normal recovery catastrophic failure have been observed in integrated circuits during the PIE period. These variations indicate that a rebound or PIE recipe used for radiation hardness assurance must be chosen with care. In this paper, the authors provide examples of PIE in a variety of integrated circuits of importance to spacecraft electronics

  4. Textbook Error: Short Circuiting on Electrochemical Cell

    Science.gov (United States)

    Bonicamp, Judith M.; Clark, Roy W.

    2007-01-01

    Short circuiting an electrochemical cell is an unreported but persistent error in the electrochemistry textbooks. It is suggested that diagrams depicting a cell delivering usable current to a load be postponed, the theory of open-circuit galvanic cells is explained, the voltages from the tables of standard reduction potentials is calculated and…

  5. Understanding the Behaviour of Infinite Ladder Circuits

    Science.gov (United States)

    Ucak, C.; Yegin, K.

    2008-01-01

    Infinite ladder circuits are often encountered in undergraduate electrical engineering and physics curricula when dealing with series and parallel combination of impedances, as a part of filter design or wave propagation on transmission lines. The input impedance of such infinite ladder circuits is derived by assuming that the input impedance does…

  6. Two New Families of Floating FDNR Circuits

    Directory of Open Access Journals (Sweden)

    Ahmed M. Soliman

    2010-01-01

    Full Text Available Two new configurations for realizing ideal floating frequency-dependent negative resistor elements (FDNR are introduced. The proposed circuits are symmetrical and are realizable by four CCII or ICCII or a combination of both. Each configuration is realizable by eight different circuits. Simulation results are included to support the theory.

  7. Designer's Casebook: current-mode minimax circuit

    NARCIS (Netherlands)

    Wassenaar, Roelof F.

    1992-01-01

    The minimum-maximum (minimax) circuit selects the minimum and maximum of two input currents. Four transistors in matched pairs are operated in the saturation region. Because the behavior of the circuit is based on matched devices and is independent of the relationship between the drain current and t

  8. Delay Reduction in Optimized Reversible Multiplier Circuit

    Directory of Open Access Journals (Sweden)

    Mohammad Assarian

    2012-01-01

    Full Text Available In this study a novel reversible multiplier is presented. Reversible logic can play a significant role in computer domain. This logic can be applied in quantum computing, optical computing processing, DNA computing, and nanotechnology. One condition for reversibility of a computable model is that the number of input equate with the output. Reversible multiplier circuits are the circuits used frequently in computer system. For this reason, optimization in one reversible multiplier circuit can reduce its volume of hardware on one hand and increases the speed in a reversible system on the other hand. One of the important parameters that optimize a reversible circuit is reduction of delays in performance of the circuit. This paper investigates the performance characteristics of the gates, the circuits and methods of optimizing the performance of reversible multiplier circuits. Results showed that reduction of the reversible circuit layers has lead to improved performance due to the reduction of the propagation delay between input and output period. All the designs are in the nanometric scales.

  9. Circuit model for cavity with a port

    International Nuclear Information System (INIS)

    These notes present, by way of an example, the calculation of lumped circuit elements to model a cavity that is connected to a transmission line through a coupling loop. This example is featured in a well-known text. It is adopted here to illustrate the concept and the procedures involved in the calculation of equivalent circuit elements. Its generalization is indicated. (author)

  10. 30 CFR 77.904 - Identification of circuit breakers.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Identification of circuit breakers. 77.904... COAL MINES Low- and Medium-Voltage Alternating Current Circuits § 77.904 Identification of circuit breakers. Circuit breakers shall be labeled to show which circuits they control unless identification...

  11. Remote tuning of NMR probe circuits.

    Science.gov (United States)

    Kodibagkar, V D; Conradi, M S

    2000-05-01

    There are many circumstances in which the probe tuning adjustments cannot be located near the rf NMR coil. These may occur in high-temperature NMR, low-temperature NMR, and in the use of magnets with small diameter access bores. We address here circuitry for connecting a fixed-tuned probe circuit by a transmission line to a remotely located tuning network. In particular, the bandwidth over which the probe may be remotely tuned while keeping the losses in the transmission line acceptably low is considered. The results show that for all resonant circuit geometries (series, parallel, series-parallel), overcoupling of the line to the tuned circuit is key to obtaining a large tuning bandwidth. At equivalent extents of overcoupling, all resonant circuit geometries have nearly equal remote tuning bandwidths. Particularly for the case of low-loss transmission line, the tuning bandwidth can be many times the tuned circuit's bandwidth, f(o)/Q. PMID:10783273

  12. Trigger circuits for the PHENIX electromagnetic calorimeter

    International Nuclear Information System (INIS)

    Monolithic and discrete circuits have been developed to provide trigger signals for the PHENIX electromagnetic calorimeter detector. These trigger circuits are deadtimeless and create overlapping 4 by 4 energy sums, a cosmic muon trigger, and a 144 channel energy sum. The front end electronics of the PHENIX system sample the energy and timing channels at each bunch crossing (BC) but it is not known immediately if this data is of interest. The information from the trigger circuits is used to determine if the data collected is of interest and should be digitized and stored or discarded. This paper presents details of the design, issues affecting circuit performance, characterization of prototypes fabricated in 1.2 microm Orbit CMOS, and integration of the circuits into the EMCal electronics system

  13. Depth-optimized reversible circuit synthesis

    Science.gov (United States)

    Arabzadeh, Mona; Saheb Zamani, Morteza; Sedighi, Mehdi; Saeedi, Mehdi

    2013-04-01

    In this paper, simultaneous reduction of circuit depth and synthesis cost of reversible circuits in quantum technologies with limited interaction is addressed. We developed a cycle-based synthesis algorithm which uses negative controls and limited distance between gate lines. To improve circuit depth, a new parallel structure is introduced in which before synthesis a set of disjoint cycles are extracted from the input specification and distributed into some subsets. The cycles of each subset are synthesized independently on different sets of ancillae. Accordingly, each disjoint set can be synthesized by different synthesis methods. Our analysis shows that the best worst-case synthesis cost of reversible circuits in the linear nearest neighbor architecture is improved by the proposed approach. Our experimental results reveal the effectiveness of the proposed approach to reduce cost and circuit depth for several benchmarks.

  14. Grounding and shielding circuits and interference

    CERN Document Server

    Morrison, Ralph

    2016-01-01

    Applies basic field behavior in circuit design and demonstrates how it relates to grounding and shielding requirements and techniques in circuit design This book connects the fundamentals of electromagnetic theory to the problems of interference in all types of electronic design. The text covers power distribution in facilities, mixing of analog and digital circuitry, circuit board layout at high clock rates, and meeting radiation and susceptibility standards. The author examines the grounding and shielding requirements and techniques in circuit design and applies basic physics to circuit behavior. The sixth edition of this book has been updated with new material added throughout the chapters where appropriate. The presentation of the book has also been rearranged in order to reflect the current trends in the field.

  15. Progress in organic integrated circuit manufacture

    Science.gov (United States)

    Taylor, D. Martin

    2016-02-01

    This review article focuses on the development of processes for the manufacture of organic electronic circuits. Beginning with the first report of an organic transistor it highlights the key developments leading to the successful manufacture of microprocessors and other complex circuits incorporating organic transistors. Both batch processing (based on silicon integrated circuit technology) as well as mass-printing, roll-to-roll (R2R) approaches are discussed. Currently, the best circuit performances are achieved using batch processing. It is suggested that an emerging, large mass-market for electronic tags may dictate that R2R manufacture will likely be required to meet the high throughput rates needed. However, significant improvements in resolution and registration are necessary to achieve increased circuit operating speeds.

  16. Low cost design of microprocessor EDAC circuit

    International Nuclear Information System (INIS)

    An optimization method of error detection and correction (EDAC) circuit design is proposed. The method involves selecting or constructing EDAC codes of low cost hardware, associated with operation scheduling implementation based on 2-input XOR gates structure, and two actions for reducing hardware cells, which can reduce the delay penalties and area costs of the EDAC circuit effectively. The 32-bit EDAC circuit hardware implementation is selected to make a prototype, based on the 180 nm process. The delay penalties and area costs of the EDAC circuit are evaluated. Results show that the time penalty and area cost of the EDAC circuitries are affected with different parity-check matrices and different hardware implementation for the EDAC codes with the same capability of correction and detection code. This method can be used as a guide for low-cost radiation-hardened microprocessor EDAC circuit design and for more advanced technologies. (paper)

  17. Analyzing the Grammar of English

    CERN Document Server

    Teschner, Richard V

    2007-01-01

    Analyzing the Grammar of English offers a descriptive analysis of the indispensable elements of English grammar. Designed to be covered in one semester, this textbook starts from scratch and takes nothing for granted beyond a reading and speaking knowledge of English. Extensively revised to function better in skills-building classes, it includes more interspersed exercises that promptly test what is taught, simplified and clarified explanations, greatly expanded and more diverse activities, and a new glossary of over 200 technical terms.Analyzing the Grammar of English is the only English gram

  18. Comparison of Sarns 3M heparin bonded to Duraflo II and control circuits in a porcine model: macro- and microanalysis of thrombi accumulation in circuit arterial filters.

    Science.gov (United States)

    Larson, D F; Arzouman, D; Kleinert, L; Patula, V; Williams, S

    2000-01-01

    Heparin-bonded perfusion circuits have been reported to reduce the thrombus formation during various levels of systemic heparinization. The goal of this study was to compare the efficacy of thrombo-resistance of the Sarns 3M heparin-bonded circuit to Baxter Duraflo II and untreated control in a porcine model. Fifteen Yorkshire pigs (60-65 kg) were anesthetized, heparinized with 3000 IU, intravenously (i.v.) and surgically cannulated with an internal jugular outflow and a femoral vein inflow. All circuits consisted of a 22-Fr venous cannula, centrifugal pump, arterial filter, an 18-Fr cannula for return and connected with equal lengths of 3/8" polyvinyl chloride tubing. The flows were maintained at 2.0 l/min for 4 h. Thrombus formation in filter samples were morphometrically analyzed through macro-densitometry, light microscopy, and scanning electron microscopy (SEM). Our findings revealed that the 3M circuit had significantly less gross thrombus (p < 0.001), 66% and 84% less microscopic thrombi and fivefold less SEM-measured aggregates (p = 0.03) compared to the Duraflo II and uncoated groups. This study demonstrated that the 3M heparin-bonded circuit had significantly reduced the formation of micro- and macro-thrombi in the minimally heparinized pig model compared to the Duraflo II and untreated control circuits.

  19. Light Sources and Ballast Circuits

    Science.gov (United States)

    Yorifuji, Takashi; Sakai, Makoto; Yasuda, Takeo; Maehara, Akiyoshi; Okada, Atsunori; Gouriki, Takeshi; Mannami, Tomoaki

    discharge models were reported. Further, studies on ultra high-pressure mercury lamps as light sources for projectors are becoming the mainstream of HID lamp related researches. For high-pressure sodium lamps, many studies on plant growing and pest control utilizing low insect attracting aspects were also reported in 2006. Additionally, for discharge lamps, the minimum sustaining electric power for arc tubes employed in electrode-less compact fluorescent lamps was investigated. For Hg-free rare-gas fluorescent lamps, a luminance of 10,000cd/m2 was attained by a 1 meter-long external duplex spiral electrode prototype using Xe/Ne barrier discharge. As to startup circuits, the commercialization of energy saving and high value added products mainly associated with fluorescent lamps and HID lamps are becoming common. Further, the miniaturization of startup circuits for self electronic-ballasted lamps has advanced. Speaking of the overall light sources and startup circuits in 2006 and with the enforcement of RoHS in Europe in July, the momentum toward hazardous substance-free and energy saving initiatives has been enhanced from the perspective of protecting the global environment. It is anticipated that similar restrictions will be globally enforced in the future.

  20. The Convertible Arbitrage Strategy Analyzed

    NARCIS (Netherlands)

    Loncarski, I.; Ter Horst, J.R.; Veld, C.H.

    2006-01-01

    This paper analyzes convertible bond arbitrage on the Canadian market for the period 1998 to 2004.Convertible bond arbitrage is the combination of a long position in convertible bonds and a short position in the underlying stocks. Convertible arbitrage has been one of the most successful strategies

  1. Software-Design-Analyzer System

    Science.gov (United States)

    Tausworthe, Robert C.

    1991-01-01

    CRISP-90 software-design-analyzer system, update of CRISP-80, is set of computer programs constituting software tool for design and documentation of other software and supporting top-down, hierarchical, modular, structured methodologies for design and programming. Written in Microsoft QuickBasic.

  2. FORTRAN Static Source Code Analyzer

    Science.gov (United States)

    Merwarth, P.

    1984-01-01

    FORTRAN Static Source Code Analyzer program, SAP (DEC VAX version), automatically gathers statistics on occurrences of statements and structures within FORTRAN program and provides reports of those statistics. Provisions made for weighting each statistic and provide an overall figure of complexity.

  3. A Novel Prediction Method about Single Components of Analog Circuits Based on Complex Field Modeling

    Directory of Open Access Journals (Sweden)

    Jingyu Zhou

    2014-01-01

    Full Text Available Few researches pay attention to prediction about analog circuits. The few methods lack the correlation with circuit analysis during extracting and calculating features so that FI (fault indicator calculation often lack rationality, thus affecting prognostic performance. To solve the above problem, this paper proposes a novel prediction method about single components of analog circuits based on complex field modeling. Aiming at the feature that faults of single components hold the largest number in analog circuits, the method starts with circuit structure, analyzes transfer function of circuits, and implements complex field modeling. Then, by an established parameter scanning model related to complex field, it analyzes the relationship between parameter variation and degeneration of single components in the model in order to obtain a more reasonable FI feature set via calculation. According to the obtained FI feature set, it establishes a novel model about degeneration trend of analog circuits’ single components. At last, it uses particle filter (PF to update parameters for the model and predicts remaining useful performance (RUP of analog circuits’ single components. Since calculation about the FI feature set is more reasonable, accuracy of prediction is improved to some extent. Finally, the foregoing conclusions are verified by experiments.

  4. Functional molecules in electronic circuits.

    Science.gov (United States)

    Weibel, Nicolas; Grunder, Sergio; Mayor, Marcel

    2007-08-01

    Molecular electronics is a fascinating field of research contributing to both fundamental science and future technological achievements. A promising starting point for molecular devices is to mimic existing electronic functions to investigate the potential of molecules to enrich and complement existing electronic strategies. Molecules designed and synthesized to be integrated into electronic circuits and to perform an electronic function are presented in this article. The focus is set in particular on rectification and switching based on molecular devices, since the control over these two parameters enables the assembly of memory units, likely the most interesting and economic application of molecular based electronics. Both historical and contemporary solutions to molecular rectification are discussed, although not exhaustively. Several examples of integrated molecular switches that respond to light are presented. Molecular switches responding to an electrochemical signal are also discussed. Finally, supramolecular and molecular systems with intuitive application potential as memory units due to their hysteretic switching are highlighted. Although a particularly attractive feature of molecular electronics is its close cooperation with neighbouring disciplines, this article is written from the point of view of a chemist. Although the focus here is largely on molecular considerations, innovative contributions from physics, electro engineering, nanotechnology and other scientific disciplines are equally important. However, the ability of the chemist to correlate function with structure, to design and to provide tailor-made functional molecules is central to molecular electronics. PMID:17637951

  5. Ion implanted dielectric elastomer circuits

    Science.gov (United States)

    O'Brien, Benjamin M.; Rosset, Samuel; Anderson, Iain A.; Shea, Herbert R.

    2013-06-01

    Starfish and octopuses control their infinite degree-of-freedom arms with panache—capabilities typical of nature where the distribution of reflex-like intelligence throughout soft muscular networks greatly outperforms anything hard, heavy, and man-made. Dielectric elastomer actuators show great promise for soft artificial muscle networks. One way to make them smart is with piezo-resistive Dielectric Elastomer Switches (DES) that can be combined with artificial muscles to create arbitrary digital logic circuits. Unfortunately there are currently no reliable materials or fabrication process. Thus devices typically fail within a few thousand cycles. As a first step in the search for better materials we present a preliminary exploration of piezo-resistors made with filtered cathodic vacuum arc metal ion implantation. DES were formed on polydimethylsiloxane silicone membranes out of ion implanted gold nano-clusters. We propose that there are four distinct regimes (high dose, above percolation, on percolation, low dose) in which gold ion implanted piezo-resistors can operate and present experimental results on implanted piezo-resistors switching high voltages as well as a simple artificial muscle inverter. While gold ion implanted DES are limited by high hysteresis and low sensitivity, they already show promise for a range of applications including hysteretic oscillators and soft generators. With improvements to implanter process control the promise of artificial muscle circuitry for soft smart actuator networks could become a reality.

  6. EMI-resilient amplifier circuits

    CERN Document Server

    van der Horst, Marcel J; Linnenbank, André C

    2014-01-01

    This book enables circuit designers to reduce the errors introduced by the fundamental limitations and electromagnetic interference (EMI) in negative-feedback amplifiers.  The authors describe a systematic design approach for application specific negative-feedback amplifiers, with specified signal-to-error ratio (SER).  This approach enables designers to calculate noise, bandwidth, EMI, and the required bias parameters of the transistors used in  application specific amplifiers in order to meet the SER requirements.   ·         Describes design methods that incorporate electromagnetic interference (EMI) in the design of application specific negative-feedback amplifiers; ·         Provides designers with a structured methodology to avoid the use of trial and error in meeting signal-to-error ratio (SER) requirements; ·         Equips designers to increase EMI immunity of the amplifier itself, thus avoiding filtering at the input, reducing the number of components and avoiding detr...

  7. Brainstem Circuits Regulating Gastric Function

    Science.gov (United States)

    Travagli, R. Alberto; Hermann, Gerlinda E.; Browning, Kirsteen N.; Rogers, Richard C.

    2011-01-01

    Brainstem parasympathetic circuits that modulate digestive functions of the stomach are comprised of afferent vagal fibers, neurons of the nucleus tractus solitarius (NTS), and the efferent fibers originating in the dorsal motor nucleus of the vagus (DMV). A large body of evidence has shown that neuronal communications between the NTS and the DMV are plastic and are regulated by the presence of a variety of neurotransmitters and circulating hormones as well as the presence, or absence, of afferent input to the NTS. These data suggest that descending central nervous system inputs as well as hormonal and afferent feedback resulting from the digestive process can powerfully regulate vago-vagal reflex sensitivity. This paper first reviews the essential “static” organization and function of vago-vagal gastric control neurocircuitry. We then present data on the opioidergic modulation of NTS connections with the DMV as an example of the “gating” of these reflexes, i.e., how neurotransmitters, hormones, and vagal afferent traffic can make an otherwise static autonomic reflex highly plastic. PMID:16460274

  8. Microcontroller based Integrated Circuit Tester

    Directory of Open Access Journals (Sweden)

    Yousif Taha Yousif Elamin

    2015-02-01

    Full Text Available The digital integrated circuit (IC tester is implemented by using the ATmega32 microcontroller . The microcontroller processes the inputs and outputs and displays the results on a Liquid Crystal Display (LCD. The basic function of the digital IC tester is to test a digital IC for correct logical functioning as described in the truth table and/or function table. The designed model can test digital ICs having 14 pins. Since it is programmable, any number of ICs can be tested . This model applies the necessary signals to the inputs of the IC, monitoring the outputs at each stage and comparing them with the outputs in the truth table. Any discrepancy in the functioning of the IC results in a fail indication, displays the faulty and good gates on the LCD. The testing procedure is accomplished with the help of keypad keys present on the main board design. The test has been accomplished with most commonly used digital IC's, mainly belonging to the 74 series. Digital IC tester tests three samples of IC's ( NAND, NOT, NOR. The design is flexible . We can add extra IC bases and subroutines to test any other IC in the 74 series.

  9. 49 CFR 236.720 - Circuit, common return.

    Science.gov (United States)

    2010-10-01

    ... Circuit, common return. A term applied where one wire is used for the return of more than one electric circuit. ... 49 Transportation 4 2010-10-01 2010-10-01 false Circuit, common return. 236.720 Section...

  10. Low-power operation using self-timed circuits and adaptive scaling of the supply voltage

    DEFF Research Database (Denmark)

    Nielsen, Lars Skovby; Niessen, C.; Sparsø, Jens;

    1994-01-01

    of voltage scaling has been used previously in synchronous circuits, and the contributions of the present paper are: 1) the combination of supply scaling and self-timed circuitry which has some unique advantages, and 2) the thorough analysis of the power savings that are possible using this technique.>......Recent research has demonstrated that for certain types of applications like sampled audio systems, self-timed circuits can achieve very low power consumption, because unused circuit parts automatically turn into a stand-by mode. Additional savings may be obtained by combining the self......-timed circuits with a mechanism that adaptively adjusts the supply voltage to the smallest possible, while maintaining the performance requirements. This paper describes such a mechanism, analyzes the possible power savings, and presents a demonstrator chip that has been fabricated and tested. The idea...

  11. Short Circuit Ratio analysis of multi-infeed HVDC system with a VSC-HVDC link

    DEFF Research Database (Denmark)

    Liu, Yan; Chen, Zhe

    2011-01-01

    As an important indicator of system stability, Short Circuit Ratio (SCR) is commonly used in power system analysis. For systems include HVDC link connection, the Effective SCR (ESCR) is mostly applied to indicate the strength of HVDC infeed bus. The contribution of VSC-HVDC link to multi......-infeed HVDC system stability has been analyzed a lot but the study on ESCR of this kind of system is still insufficient. This paper presents a calculation method for ESCR of the hybrid multi infeed HVDC system based on a simple two-infeed HVDC system model. The equivalent circuit of this system under short...... circuit situation is firstly obtained based on the model. Then its Thevenin equivalent circuit is derived and system ESCR can be calculated. At last, simulation study verified that the calculated ESCR value under different cases can indicate the change of system stability....

  12. Design of Microcantilever-Based Biosensor with Digital Feedback Control Circuit

    Directory of Open Access Journals (Sweden)

    Jayu P. Kalambe

    2012-01-01

    Full Text Available This paper present the design of cantilever-based biosensors with new readout, which hold promises as fast and cheap “point of care” device as well as interesting research tools. The fabrication process and related issues of the cantilever based bio-sensor are discussed. Coventorware simulation is carried out to analyze the device behavior. A fully integrated control circuit has been designed to solve manufacturing challenge which will take care of positioning of the cantilever instead of creating nanometer gap between the electrodes. The control circuit will solve the manufacturing challenge faced by the readout methods where it is essential to maintain precise gap between the electrodes. The circuit can take care of variation obtained due to fabrication process and maintain the precise gap between the electrodes by electrostatic actuation. The control circuit consist of analog and digital modules. The reliability issues of the sensor are also discussed.

  13. Performance Comparison of CMOS and Finfet Based Circuits At 45nm Technology Using SPICE

    Directory of Open Access Journals (Sweden)

    Mugdha Sathe

    2014-07-01

    Full Text Available According to the Moore’s Law, the number of transistors in a unit chip area double every two years. But the existing technology of integrated circuit formation is posing limitations to this law. CMOS technology shows certain limitations as the device is reduced more and more in the nanometer regime out of which power dissipation is an important issue. FinFET is evolving to be a promising technology in this regard. This paper aims to analyze and compare the characteristics of CMOS and FinFET circuits at 45nm technology. Inverter circuit is implemented in order to study the basic characteristics such as voltage transfer characteristics, leakage current and power dissipation. Further the efficiency of FinFET to reduce power as compared to CMOS is proved using SRAM circuit. The results show that the average power is reduced by 92.93% in read operation and by 97.8% in write operation.

  14. Short-Circuit Calculation in Distribution Networks with Distributed Induction Generators

    Directory of Open Access Journals (Sweden)

    Niancheng Zhou

    2016-04-01

    Full Text Available This paper presents an improved current source equivalent model method to determine the short-circuit current of a distribution system with multiple fixed-speed and variable-speed induction generators (IGs. The correlation coefficients of flux components between stator and rotor under the unsymmetrical fault are analyzed using the positive and negative sequence steady-state equivalent circuits of an IG. The terminal voltage and current responses of fixed-speed and variable-speed IGs with and without the rotor slip changes under different penetration levels are compared to investigate the coupling relation between the short-circuit currents of IGs and the nodal voltages in the distribution network. Then the transient equivalent potential of an IG at the grid fault instant is derived. Sequence components of the short-circuit current in the network can be determined using the proposed technique. The correctness of the proposed method is verified using dynamic simulation.

  15. Development of a Dynamic Population Balance Plant Simulator for Mineral Processing Circuits

    Directory of Open Access Journals (Sweden)

    Fatemeh Khoshnam

    2015-06-01

    Full Text Available Operational variables of a mineral processing circuit are subjected to different variations. Steady-statesimulation of processes provides an estimate of their ideal stable performance whereas their dynamicsimulation predicts the effects of the variations on the processes or their subsequent processes. In thispaper, a dynamic simulator containing some of the major equipment of mineral processing circuits(i.e. ball mill, cone crusher, screen, hydrocyclone, mechanical flotation cell, tank leaching andconveyor belt was developed. The dynamic simulator of each mentioned unit was also developedaccording to population balance models with the help of MATLAB/Simulink environment and wasverified against the data from the literature. Comminution and separation sections were linked usingempirical models which correlate the separation and extraction kinetics to particle size. Applying thedeveloped simulator, the dynamic behavior of a grinding-leaching circuit was analyzed and the resultsshowed that such simulations are required for both designing and controlling the circuits.

  16. Online Monitoring System Design of Intelligent Circuit Breaker Based on DSP and ARM

    Directory of Open Access Journals (Sweden)

    Meng Song

    2014-08-01

    Full Text Available In order to accurately analyze the dynamic characteristics of the vacuum circuit breaker, a dual-core master-slave processor structure for online monitoring system based on DSP and ARM is proposed. This structure consists of host computer, lower computer and signal processing modules. The lower computer uses DSP as the core, which completes acquisition and data preprocessing of circuit breaker’s dynamic characteristics through sensors and signal conditioning circuits. The host computer uses ARM as the core which is responsible for task management, analysis, processing and displaying collected data via Ethernet. The communication between DSP and ARM is conducted by HPI. This design improves the reliability of intelligent control unit for the circuit breaker. The experiment showed that this system works steadily and accuracy.

  17. Fundamental Approach in Digital Circuit Design for 1-MHz Frequency PWM Gate Drive Application

    Directory of Open Access Journals (Sweden)

    Nor Zaihar Yahaya

    2011-01-01

    Full Text Available This paper discusses the design of a digital programmable logic circuit to produce a 5 V - output square wave pulses for four high power MOSFET switches using a fixed PWM circuit. It will be applied to drive the synchronous rectifier buck converter(SRBC circuit. The PWM signals with multiple fixed time delay of 15 ns, 232 ns, 284 ns and 955 ns are generated. The steps taken to analyze each propagation time delay of each logic gate used and its combination are carefully studied. A multiplexer is added at the output of the logic circuit to select and produce the desired output pulses of 20% duty ratio. The logic outputs are compared with the analog pulses and results match each other within 1% in difference.

  18. Biologic: Gene circuits and feedback in an introductory physics sequence for biology and premedical students

    CERN Document Server

    Cahn, S B

    2013-01-01

    Two synthetic gene circuits -- the genetic toggle switch and the repressilator -- are analyzed quantitatively and discussed in the context of an educational module on gene circuits and feedback that constitutes the final topic of a year-long introductory physics sequence, aimed at biology and premedical undergraduate students. The genetic toggle switch consists of two genes, each of whose protein product represses the other's expression, while the repressilator consists of three genes, each of whose protein product represses the next gene's expression. Analytic, numerical, and electronic treatments of the genetic toggle switch shows that this gene circuit realizes bistability. A simplified treatment of the repressilator reveals that this circuit can realize sustained oscillations. In both cases, a "phase diagram" is obtained, that specifies the region of parameter space in which bistability or oscillatory behavior, respectively, occurs.

  19. Visualization of circuit card electromagnetic fields

    Science.gov (United States)

    Zwillinger, Daniel

    1995-01-01

    Circuit boards are used in nearly every electrical appliance. Most board failures cause differing currents in the circuit board traces and components. This causes the circuit board to radiate a differing electromagnetic field. Imaging this radiated field, which is equivalent to measuring the field, could be used for error detection. Using estimates of the fields radiated by a low power digital circuit board, properties of known materials, and available equipment, we determined how well the following technologies could be used to visualize circuit board electromagnetic fields (prioritized by promise): electrooptical techniques, magnetooptical techniques, piezoelectric techniques, thermal techniques, and electrodynamic force technique. We have determined that sensors using the electrooptical effect (Pockels effect) appear to be sufficiently sensitive for use in a circuit board imaging system. Sensors utilizing the magnetooptical effect may also be adequate for this purpose, when using research materials. These sensors appear to be capable of achieving direct broadband measurements. We also reviewed existing electromagnetic field sensors. Only one of the sensors (recently patented) was specifically designed for circuit board measurements.

  20. BETA: Behavioral testability analyzer and its application to high-level test generation and synthesis for testability. Ph.D. Thesis

    Science.gov (United States)

    Chen, Chung-Hsing

    1992-01-01

    In this thesis, a behavioral-level testability analysis approach is presented. This approach is based on analyzing the circuit behavioral description (similar to a C program) to estimate its testability by identifying controllable and observable circuit nodes. This information can be used by a test generator to gain better access to internal circuit nodes and to reduce its search space. The results of the testability analyzer can also be used to select test points or partial scan flip-flops in the early design phase. Based on selection criteria, a novel Synthesis for Testability approach call Test Statement Insertion (TSI) is proposed, which modifies the circuit behavioral description directly. Test Statement Insertion can also be used to modify circuit structural description to improve its testability. As a result, Synthesis for Testability methodology can be combined with an existing behavioral synthesis tool to produce more testable circuits.

  1. Methods for Analyzing Social Media

    DEFF Research Database (Denmark)

    Jensen, Jakob Linaa

    2013-01-01

    Social media is becoming increasingly attractive for users. It is a fast way to communicate ideas and a key source of information. It is therefore one of the most influential mediums of communication of our time and an important area for audience research. The growth of social media invites many...... new questions such as: How can we analyze social media? Can we use traditional audience research methods and apply them to online content? Which new research strategies have been developed? Which ethical research issues and controversies do we have to pay attention to? This book focuses on research...... strategies and methods for analyzing social media and will be of interest to researchers and practitioners using social media, as well as those wanting to keep up to date with the subject....

  2. Introduction: why analyze single cells?

    Science.gov (United States)

    Di Carlo, Dino; Tse, Henry Tat Kwong; Gossett, Daniel R

    2012-01-01

    Powerful methods in molecular biology are abundant; however, in many fields including hematology, stem cell biology, tissue engineering, and cancer biology, data from tools and assays that analyze the average signals from many cells may not yield the desired result because the cells of interest may be in the minority-their behavior masked by the majority-or because the dynamics of the populations of interest are offset in time. Accurate characterization of samples with high cellular heterogeneity may only be achieved by analyzing single cells. In this chapter, we discuss the rationale for performing analyses on individual cells in more depth, cover the fields of study in which single-cell behavior is yielding new insights into biological and clinical questions, and speculate on how single-cell analysis will be critical in the future.

  3. The Statistical Loop Analyzer (SLA)

    Science.gov (United States)

    Lindsey, W. C.

    1985-01-01

    The statistical loop analyzer (SLA) is designed to automatically measure the acquisition, tracking and frequency stability performance characteristics of symbol synchronizers, code synchronizers, carrier tracking loops, and coherent transponders. Automated phase lock and system level tests can also be made using the SLA. Standard baseband, carrier and spread spectrum modulation techniques can be accomodated. Through the SLA's phase error jitter and cycle slip measurements the acquisition and tracking thresholds of the unit under test are determined; any false phase and frequency lock events are statistically analyzed and reported in the SLA output in probabilistic terms. Automated signal drop out tests can be performed in order to trouble shoot algorithms and evaluate the reacquisition statistics of the unit under test. Cycle slip rates and cycle slip probabilities can be measured using the SLA. These measurements, combined with bit error probability measurements, are all that are needed to fully characterize the acquisition and tracking performance of a digital communication system.

  4. Satellite-based interference analyzer

    Science.gov (United States)

    Varice, H.; Johannsen, K.; Sabaroff, S.

    1977-01-01

    System identifies terrestrial sources of radiofrequency interference and measures their frequency spectra and amplitudes. Designed to protect satellite communication networks, system measures entire noise spectrum over selected frequency band and can raster-scan geographical region to locate noise sources. Once interference is analyzed, realistic interference protection ratios are determined and mathematical models for predicting ratio-frequency noise spectra are established. This enhances signal-detection and locates optimum geographical positions and frequency bands for communication equipment.

  5. Reversible and quantum circuits optimization and complexity analysis

    CERN Document Server

    Abdessaied, Nabila

    2016-01-01

    This book presents a new optimization flow for quantum circuits realization. At the reversible level, optimization algorithms are presented to reduce the quantum cost. Then, new mapping approaches to decompose reversible circuits to quantum circuits using different quantum libraries are described. Finally, optimization techniques to reduce the quantum cost or the delay are applied to the resulting quantum circuits. Furthermore, this book studies the complexity of reversible circuits and quantum circuits from a theoretical perspective.

  6. Short-circuit forces in power lines and substations.

    OpenAIRE

    Lilien, Jean-Louis; Goel, Anand

    2009-01-01

    This chapter discusses short-circuit oscillations in power lines. Short-circuit currents generate electromagnetic forces on the conductors, exciting short-circuit oscillations. Since the short-circuit periods are very short, the short-circuit forces in single conductor overhead lines are usually low because of the large phase spacing. However these forces may have considerable impact on distribution lines due to the change in phase spacing during short-circuit occurrences. For bundle conducto...

  7. Analyzing Big Data in Psychology: A Split/Analyze/Meta-Analyze Approach.

    Science.gov (United States)

    Cheung, Mike W-L; Jak, Suzanne

    2016-01-01

    Big data is a field that has traditionally been dominated by disciplines such as computer science and business, where mainly data-driven analyses have been performed. Psychology, a discipline in which a strong emphasis is placed on behavioral theories and empirical research, has the potential to contribute greatly to the big data movement. However, one challenge to psychologists-and probably the most crucial one-is that most researchers may not have the necessary programming and computational skills to analyze big data. In this study we argue that psychologists can also conduct big data research and that, rather than trying to acquire new programming and computational skills, they should focus on their strengths, such as performing psychometric analyses and testing theories using multivariate analyses to explain phenomena. We propose a split/analyze/meta-analyze approach that allows psychologists to easily analyze big data. Two real datasets are used to demonstrate the proposed procedures in R. A new research agenda related to the analysis of big data in psychology is outlined at the end of the study.

  8. Analyzing Big Data in Psychology: A Split/Analyze/Meta-Analyze Approach

    Science.gov (United States)

    Cheung, Mike W.-L.; Jak, Suzanne

    2016-01-01

    Big data is a field that has traditionally been dominated by disciplines such as computer science and business, where mainly data-driven analyses have been performed. Psychology, a discipline in which a strong emphasis is placed on behavioral theories and empirical research, has the potential to contribute greatly to the big data movement. However, one challenge to psychologists—and probably the most crucial one—is that most researchers may not have the necessary programming and computational skills to analyze big data. In this study we argue that psychologists can also conduct big data research and that, rather than trying to acquire new programming and computational skills, they should focus on their strengths, such as performing psychometric analyses and testing theories using multivariate analyses to explain phenomena. We propose a split/analyze/meta-analyze approach that allows psychologists to easily analyze big data. Two real datasets are used to demonstrate the proposed procedures in R. A new research agenda related to the analysis of big data in psychology is outlined at the end of the study. PMID:27242639

  9. Analyzing Big Data in Psychology: A Split/Analyze/Meta-Analyze Approach

    Directory of Open Access Journals (Sweden)

    Mike W.-L. Cheung

    2016-05-01

    Full Text Available Big data is a field that has traditionally been dominated by disciplines such as computer science and business, where mainly data-driven analyses have been performed. Psychology, a discipline in which a strong emphasis is placed on behavioral theories and empirical research, has the potential to contribute greatly to the big data movement. However, one challenge to psychologists – and probably the most crucial one – is that most researchers may not have the necessary programming and computational skills to analyze big data. In this study we argue that psychologists can also conduct big data research and that, rather than trying to acquire new programming and computational skills, they should focus on their strengths, such as performing psychometric analyses and testing theories using multivariate analyses to explain phenomena. We propose a split/analyze/meta-analyze approach that allows psychologists to easily analyze big data. Two real datasets are used to demonstrate the proposed procedures in R. A new research agenda related to the analysis of big data in psychology is outlined at the end of the study.

  10. Equivalent circuit analysis of terahertz metamaterial filters

    KAUST Repository

    Zhang, Xueqian

    2011-01-01

    An equivalent circuit model for the analysis and design of terahertz (THz) metamaterial filters is presented. The proposed model, derived based on LMC equivalent circuits, takes into account the detailed geometrical parameters and the presence of a dielectric substrate with the existing analytic expressions for self-inductance, mutual inductance, and capacitance. The model is in good agreement with the experimental measurements and full-wave simulations. Exploiting the circuit model has made it possible to predict accurately the resonance frequency of the proposed structures and thus, quick and accurate process of designing THz device from artificial metamaterials is offered. ©2011 Chinese Optics Letters.

  11. The Drosophila melanogaster circadian pacemaker circuit

    Indian Academy of Sciences (India)

    Vasu Sheeba

    2008-12-01

    As an experimental model system, the fruit fly Drosophila melanogaster has been seminal in shaping our understanding of the circadian clockwork. The wealth of genetic tools at our disposal over the past four decades has enabled discovery of the genetic and molecular bases of circadian rhythmicity. More recently, detailed investigation leading to the anatomical, neurochemical and electrophysiological characterization of the various neuronal subgroups that comprise the circadian machinery has revealed pathways through which these neurons come together to act as a neuronal circuit. Thus the D. melanogaster circadian pacemaker circuit presents a relatively simple and attractive model for the study of neuronal circuits and their functions.

  12. Some results on uniform arithmetic circuit complexity

    DEFF Research Database (Denmark)

    Frandsen, Gudmund Skovbjerg; Valence, Mark; Barrington, David A. Mix

    1994-01-01

    and polynomial-size unbounded fan-in arithmetic circuits satisfying a natural uniformity constraint (DLOGTIME-uniformity). A 1-input and 1-output arithmetic function over the fieldsF2n may be identified with ann-input andn-output Boolean function when field elements are represented as bit strings. We prove...... that if some such representation is X-uniform (where X is P or DLOGTIME), then the arithmetic complexity of a function (measured with X-uniform unbounded fan-in arithmetic circuits) is identical to the Boolean complexity of this function (measured with X-uniform threshold circuits). We show the existence...

  13. Circuits with arbitrary gates for random operators

    OpenAIRE

    Jukna, S.; Schnitger, G.

    2010-01-01

    We consider boolean circuits computing n-operators f:{0,1}^n --> {0,1}^n. As gates we allow arbitrary boolean functions; neither fanin nor fanout of gates is restricted. An operator is linear if it computes n linear forms, that is, computes a matrix-vector product y=Ax over GF(2). We prove the existence of n-operators requiring about n^2 wires in any circuit, and linear n-operators requiring about n^2/\\log n wires in depth-2 circuits, if either all output gates or all gates on the middle laye...

  14. Operational amplifier circuits analysis and design

    CERN Document Server

    Nelson, J C C

    1995-01-01

    This book, a revised and updated version of the author's Basic Operational Amplifiers (Butterworths 1986), enables the non-specialist to make effective use of readily available integrated circuit operational amplifiers for a range of applications, including instrumentation, signal generation and processing.It is assumed the reader has a background in the basic techniques of circuit analysis, particularly the use of j notation for reactive circuits, with a corresponding level of mathematical ability. The underlying theory is explained with sufficient but not excessive, detail. A range of compu

  15. An introduction to logic circuit testing

    CERN Document Server

    Lala, Parag K

    2008-01-01

    An Introduction to Logic Circuit Testing provides a detailed coverage of techniques for test generation and testable design of digital electronic circuits/systems. The material covered in the book should be sufficient for a course, or part of a course, in digital circuit testing for senior-level undergraduate and first-year graduate students in Electrical Engineering and Computer Science. The book will also be a valuable resource for engineers working in the industry. This book has four chapters. Chapter 1 deals with various types of faults that may occur in very large scale integration (VLSI)

  16. Theory of circuit block switch-off

    Directory of Open Access Journals (Sweden)

    S. Henzler

    2004-01-01

    Full Text Available Switching-off unused circuit blocks is a promising approach to supress static leakage currents in ultra deep sub-micron CMOS digital systems. Basic performance parameters of Circuit Block Switch-Off (CBSO schemes are defined and their dependence on basic circuit parameters is estimated. Therefore the design trade-off between strong leakage suppression in idle mode and adequate dynamic performance in active mode can be supported by simple analytic investigations. Additionally, a guideline for the estimation of the minimum time for which a block deactivation is useful is derived.

  17. A guide to printed circuit board design

    CERN Document Server

    Hamilton, Charles

    1984-01-01

    A Guide to Printed Circuit Board Design discusses the basic design principles of printed circuit board (PCB). The book consists of nine chapters; each chapter provides both text discussion and illustration relevant to the topic being discussed. Chapter 1 talks about understanding the circuit diagram, and Chapter 2 covers how to compile component information file. Chapter 3 deals with the design layout, while Chapter 4 talks about preparing the master artworks. The book also covers generating computer aided design (CAD) master patterns, and then discusses how to prepare the production drawing a

  18. Power electronics handbook components, circuits and applications

    CERN Document Server

    Mazda, F F

    2013-01-01

    Power Electronics Handbook: Components, Circuits, and Applications is a collection of materials about power components, circuit design, and applications. Presented in a practical form, theoretical information is given as formulae. The book is divided into three parts. Part 1 deals with the usual components found in power electronics such as semiconductor devices and power semiconductor control components, their electronic compatibility, and protection. Part 2 tackles parts and principles related to circuits such as switches; link frequency chargers; converters; and AC line control, and Part 3

  19. Starting Circuit For Erasable Programmable Logic Device

    Science.gov (United States)

    Cole, Steven W.

    1990-01-01

    Voltage regulator bypassed to supply starting current. Starting or "pullup" circuit supplies large inrush of current required by erasable programmable logic device (EPLD) while being turned on. Operates only during such intervals of high demand for current and has little effect any other time. Performs needed bypass, acting as current-dependent shunt connecting battery or other source of power more nearly directly to EPLD. Input capacitor of regulator removed when starting circuit installed, reducing probability of damage to transistor in event of short circuit in or across load.

  20. Newnes passive and discrete circuits pocket book

    CERN Document Server

    MARSTON, R M

    2000-01-01

    Newnes Passive and Discrete Circuits Pocket Book is aimed at all engineers, technicians, students and experimenters who can build a design directly from a circuit diagram. In a highly concise form Ray Marston presents a huge compendium of circuits that can be built as they appear, adapted or used as building blocks. The devices used have been carefully chosen for their ease of availability and reasonable price. The selection of devices has been thoroughly updated for the second edition, which has also been expanded to cover the latest ICs.The three sections of the book cover: Moder

  1. Maximally positive polynomial systems supported on circuits

    OpenAIRE

    Bihan, Frédéric

    2013-01-01

    A real polynomial system with support $\\calW \\subset \\Z^n$ is called {\\it maximally positive} if all its complex solutions are positive solutions. A support $\\calW$ having $n+2$ elements is called a circuit. We previously showed that the number of non-degenerate positive solutions of a system supported on a circuit $\\calW \\subset\\Z^n$ is at most $m(\\calW)+1$, where $m(\\calW) \\leq n$ is the degeneracy index of $\\calW$. We prove that if a circuit $\\calW \\subset \\Z^n$ supports a maximally positi...

  2. Analog circuit design for communication SOC

    CERN Document Server

    Tu, Steve Hung-Lung

    2012-01-01

    This e-book provides several state-of-the-art analog circuit design techniques. It presents both empirical and theoretical materials for system-on-a-chip (SOC) circuit design. Fundamental communication concepts are used to explain a variety of topics including data conversion (ADC, DAC, S-? oversampling data converters), clock data recovery, phase-locked loops for system timing synthesis, supply voltage regulation, power amplifier design, and mixer design. This is an excellent reference book for both circuit designers and researchers who are interested in the field of design of analog communic

  3. Radio-frequency integrated-circuit engineering

    CERN Document Server

    Nguyen, Cam

    2015-01-01

    Radio-Frequency Integrated-Circuit Engineering addresses the theory, analysis and design of passive and active RFIC's using Si-based CMOS and Bi-CMOS technologies, and other non-silicon based technologies. The materials covered are self-contained and presented in such detail that allows readers with only undergraduate electrical engineering knowledge in EM, RF, and circuits to understand and design RFICs. Organized into sixteen chapters, blending analog and microwave engineering, Radio-Frequency Integrated-Circuit Engineering emphasizes the microwave engineering approach for RFICs. Provide

  4. Semiconductors integrated circuit design for manufacturability

    CERN Document Server

    Balasinki, Artur

    2011-01-01

    Because of the continuous evolution of integrated circuit manufacturing (ICM) and design for manufacturability (DfM), most books on the subject are obsolete before they even go to press. That's why the field requires a reference that takes the focus off of numbers and concentrates more on larger economic concepts than on technical details. Semiconductors: Integrated Circuit Design for Manufacturability covers the gradual evolution of integrated circuit design (ICD) as a basis to propose strategies for improving return-on-investment (ROI) for ICD in manufacturing. Where most books put the spotl

  5. Silicon integrated circuits part A : supplement 2

    CERN Document Server

    Kahng, Dawon

    1981-01-01

    Applied Solid State Science, Supplement 2: Silicon Integrated Circuits, Part A focuses on MOS device physics. This book is divided into three chapters-physics of the MOS transistor; nonvolatile memories; and properties of silicon-on-sapphire substrates devices, and integrated circuits. The topics covered include the short channel effects, MOSFET structures, floating gate devices, technology for nonvolatile semiconductor memories, sapphire substrates, and SOS integrated circuits and systems. The MOS capacitor, MIOS devices, and SOS process and device technology are also deliberated. This public

  6. Tool for Crimping Flexible Circuit Leads

    Science.gov (United States)

    Hulse, Aaron; Diftler, Myron A.

    2009-01-01

    A hand tool has been developed for crimping leads in flexible tails that are parts of some electronic circuits -- especially some sensor circuits. The tool is used to cut the tails to desired lengths and attach solder tabs to the leads. For tailoring small numbers of circuits for special applications, this hand tool is a less expensive alternative to a commercially available automated crimping tool. The crimping tool consists of an off-the-shelf hand crimping tool plus a specialized crimping insert designed specifically for the intended application.

  7. Ambient temperature cadmium zinc telluride radiation detector and amplifier circuit

    International Nuclear Information System (INIS)

    A low noise, low power consumption, compact, ambient temperature signal amplifier for a Cadmium Zinc Telluride (CZT) radiation detector is disclosed. The amplifier can be used within a larger system (e.g., including a multi-channel analyzer) to allow isotopic analysis of radionuclides in the field. In one embodiment, the circuit stages of the low power, low noise amplifier are constructed using integrated circuit (IC) amplifiers , rather than discrete components, and include a very low noise, high gain, high bandwidth dual part preamplification stage, an amplification stage, and an filter stage. The low noise, low power consumption, compact, ambient temperature amplifier enables the CZT detector to achieve both the efficiency required to determine the presence of radionuclides and the resolution necessary to perform isotopic analysis to perform nuclear material identification. The present low noise, low power, compact, ambient temperature amplifier enables a CZT detector to achieve resolution of less than 3% full width at half maximum at 122 keV for a Cobalt-57 isotope source. By using IC circuits and using only a single 12 volt supply and ground, the novel amplifier provides significant power savings and is well suited for prolonged portable in-field use and does not require heavy, bulky power supply components. 9 figs

  8. Integrating anatomy and function for zebrafish circuit analysis.

    Science.gov (United States)

    Arrenberg, Aristides B; Driever, Wolfgang

    2013-01-01

    Due to its transparency, virtually every brain structure of the larval zebrafish is accessible to light-based interrogation of circuit function. Advanced stimulation techniques allow the activation of optogenetic actuators at different resolution levels, and genetically encoded calcium indicators report the activity of a large proportion of neurons in the CNS. Large datasets result and need to be analyzed to identify cells that have specific properties-e.g., activity correlation to sensory stimulation or behavior. Advances in three-dimensional (3D) functional mapping in zebrafish are promising; however, the mere coordinates of implicated neurons are not sufficient. To comprehensively understand circuit function, these functional maps need to be placed into the proper context of morphological features and projection patterns, neurotransmitter phenotypes, and key anatomical landmarks. We discuss the prospect of merging functional and anatomical data in an integrated atlas from the perspective of our work on long-range dopaminergic neuromodulation and the oculomotor system. We propose that such a resource would help researchers to surpass current hurdles in circuit analysis to achieve an integrated understanding of anatomy and function.

  9. A New Improved MCML Logic for DPA Resistant Circuits

    Directory of Open Access Journals (Sweden)

    A.K.Tripathy

    2013-10-01

    Full Text Available Security of electronic data remains the major conce rn. The art of encryption to secure the data can be achieved in various levels of abstraction. The choi ce of the logic style in implementing the security algorithms has greater significance, and it can enh ance the ability of providing better resistance to side channel attacks. The static CMOS logic style is pro ved to be prone to side channel power attacks. The exploration of CMOS current mode logic style for re sistance against these side channel attacks is disc ussed in this paper. Various characteristics of the curre nt mode logic styles, which make it suitable for ma king DPA resistant circuits are explored. A new methodol ogy of biasing the sleep transistors of (MOS curren t mode logic MCML families is proposed. It uses pass gate transistors for power-gating the circuits. Th e power variations of the proposed circuits are compa red against the standard CMOS counterparts. Logic gates such as XOR, NAND and AND gate structures of MCML families and static CMOS are designed and compared for the ability of side channel resistance . A distributed arrangement of sleep transistors fo r reducing the static power dissipation in the logic gates is also proposed, designed and analyzed. All the logic gates in MCML and CMOS were implemented using standard 180 nm CMOS technology employing Cadence® EDA tools

  10. Competitive Learning in Electric Circuit Theory Using MOODLE

    Science.gov (United States)

    Barroso, Ramón J. Durán; Bahillo, Alfonso; Fernández, Patricia; Merayo, Noemí; de Miguel, Ignacio; Aguado, Juan Carlos; Lorenzo, Rubén M.; Domi, Evaristo J. Abril

    We have recently introduced an activity based on competitive learning in the subject of "Electric Circuit Theory", which is taught in the first year of the 3-year degree of Technical Telecommunication Engineering at the University of Valladolid. Students are divided into groups and compete in a tournament through a series of knockout rounds. In each of these rounds, a contending group solves an electric circuit problem, and proposes an update on it, which must then be solved by the other contending team, and so on until one of them fails. In order to facilitate the management of the game, the open-source MOODLE platform has been employed. This paper describes the experience and the learning benefits that it brings, as well as how the method has been implemented using the MOODLE platform. Moreover, the satisfaction of the students and the time required by the students and by the teacher when using this technique are also analyzed. While the experience focuses on the subject of "Electric Circuit Theory", it is worthy to note that it may be easily extended to other subjects.

  11. Variation-aware adaptive voltage scaling for digital CMOS circuits

    CERN Document Server

    Wirnshofer, Martin

    2013-01-01

    Increasing performance demands in integrated circuits, together with limited energy budgets, force IC designers to find new ways of saving power. One innovative way is the presented adaptive voltage scaling scheme, which tunes the supply voltage according to the present process, voltage and temperature variations as well as aging. The voltage is adapted “on the fly” by means of in-situ delay monitors to exploit unused timing margin, produced by state-of-the-art worst-case designs. This book discusses the design of the enhanced in-situ delay monitors and the implementation of the complete control-loop comprising the monitors, a control-logic and an on-chip voltage regulator. An analytical Markov-based model of the control-loop is derived to analyze its robustness and stability. Variation-Aware Adaptive Voltage Scaling for Digital CMOS Circuits provides an in-depth assessment of the proposed voltage scaling scheme when applied to an arithmetic and an image processing circuit. This book is written for engine...

  12. High Quality Acquisition of Surface Electromyography – Conditioning Circuit Design

    International Nuclear Information System (INIS)

    The acquisition of Surface Electromyography (SEMG) signals is used for many applications including the diagnosis of neuromuscular diseases, and prosthesis control. The diagnostic quality of the SEMG signal is highly dependent on the conditioning circuit of the SEMG acquisition system. This paper presents the design of an SEMG conditioning circuit that can guarantee to collect high quality signal with high SNR such that it is immune to environmental noise. The conditioning circuit consists of four stages; consisting of an instrumentation amplifier that is used with a gain of around 250; 4th order band pass filter in the 20–500Hz frequency range as the two initial stages. The third stage is an amplifier with adjustable gain using a variable resistance; the gain could be changed from 1000 to 50000. In the final stage the signal is translated to meet the input requirements of data acquisition device or the ADC. Acquisition of accurate signals allows it to be analyzed for extracting the required characteristic features for medical and clinical applications. According to the experimental results, the value of SNR for collected signal is 52.4 dB which is higher than the commercial system, the power spectrum density (PSD) graph is also presented and it shows that the filter has eliminated the noise below 20 Hz

  13. A New Defected Ground Structure for Different Microstrip Circuit Applications

    Directory of Open Access Journals (Sweden)

    S. Das

    2007-04-01

    Full Text Available In this paper, a microstrip transmission line combined with a new U-headed dumb-bell defected ground structure (DGS is investigated. The proposed DGS of two U-shape slots connected by a thin transverse slot is placed in the ground plane of a microstrip line. A finite cutoff frequency and attenuation pole is observed and thus, the equivalent circuit of the DGS unit can be represented by a parallel LC resonant circuit in series with the transmission line. A two-cell DGS microstrip line yields a better lowpass filtering characteristics. The simulation is carried out by the MoM based IE3D software and in the experimental measurements a vector network analyzer is used. The effects of the transverse slot width and the distance between arms of the U-slot on the filter response curve are studied. This DGS is utilized for different microstrip circuit applications. The DGS is placed in the ground of a capacitive loaded microstrip line and a very low cutoff frequency is obtained. The DGS is adopted under the coupled lines of a parallel line coupler and an improvement in coupling coefficient is noticed. The proposed DGS is also incorporated in the ground plane under the feed lines and the coupled lines of a bandpass filter to improve separately the stopband and passband performances.

  14. 配电变压器绕组轴向短路电磁力分析%Analysis of Axial Short Circuit Electromagnetic Force in Winding of Distribution Transformer

    Institute of Scientific and Technical Information of China (English)

    李朝生; 郭健; 李先允; 陈小虎

    2011-01-01

    建立了计算短路电流的三维暂态场路耦合模型,对短路电流和轴向短路电磁力进行了比较分析.%The 3D transient field circuit coupled model to calculate short circuit current is established. The short circuit current and the axial short circuit electromagnetic force are comparied and analyzed.

  15. The Aqueduct Global Flood Analyzer

    Science.gov (United States)

    Iceland, Charles

    2015-04-01

    As population growth and economic growth take place, and as climate change accelerates, many regions across the globe are finding themselves increasingly vulnerable to flooding. A recent OECD study of the exposure of the world's large port cities to coastal flooding found that 40 million people were exposed to a 1 in 100 year coastal flood event in 2005, and the total value of exposed assets was about US 3,000 billion, or 5% of global GDP. By the 2070s, those numbers were estimated to increase to 150 million people and US 35,000 billion, or roughly 9% of projected global GDP. Impoverished people in developing countries are particularly at risk because they often live in flood-prone areas and lack the resources to respond. WRI and its Dutch partners - Deltares, IVM-VU University Amsterdam, Utrecht University, and PBL Netherlands Environmental Assessment Agency - are in the initial stages of developing a robust set of river flood and coastal storm surge risk measures that show the extent of flooding under a variety of scenarios (both current and future), together with the projected human and economic impacts of these flood scenarios. These flood risk data and information will be accessible via an online, easy-to-use Aqueduct Global Flood Analyzer. We will also investigate the viability, benefits, and costs of a wide array of flood risk reduction measures that could be implemented in a variety of geographic and socio-economic settings. Together, the activities we propose have the potential for saving hundreds of thousands of lives and strengthening the resiliency and security of many millions more, especially those who are most vulnerable. Mr. Iceland will present Version 1.0 of the Aqueduct Global Flood Analyzer and provide a preview of additional elements of the Analyzer to be released in the coming years.

  16. Fuel analyzer; Analisador de combustiveis

    Energy Technology Data Exchange (ETDEWEB)

    Cozzolino, Roberval [RS Motors, Indaiatuba, SP (Brazil)

    2008-07-01

    The current technology 'COMBUSTIMETRO' aims to examine the fuel through performance of the engine, as the role of the fuel is to produce energy for the combustion engine in the form of which is directly proportional to the quality and type of fuel. The 'COMBUSTIMETRO' has an engine that always keeps the same entry of air, fuel and fixed point of ignition. His operation is monitored by sensors (Sonda Lambda, RPM and Gases Analyzer) connected to a processor that performs calculations and records the information, generate reports and graphs. (author)

  17. [Examination of the olfactory analyzer].

    Science.gov (United States)

    Domrachev, A A; Afon'kin, V Iu

    2002-01-01

    A method of threshold olfactometry is proposed consisting in the use of three olfactive substances (tincture of valerian, acetic acid, liquid ammonia) in selected concentrations. This allows to investigate the thresholds of certain modality. Each concentration of the olfactive substance is placed into a glass bottle (100 ml) and stored at the temperature 18-20 degrees C. The examination of the state of the olfactory analyzer within a 24-h working day showed stability of threshold olfactometry when the organism is tired. Utilization of threshold olfactometry in some diagnostic areas is shown. PMID:12056163

  18. Local random quantum circuits: ensemble CP maps and swap algebras

    OpenAIRE

    Zanardi, Paolo

    2013-01-01

    We define different classes of local random quantum circuits (L-RQC) and show that: a) statistical properties of L-RQC are encoded into an associated family of completely positive maps and b) average purity dynamics can be described by the action of these maps on operator algebras of permutations (swap algebras). An exactly solvable one-dimensional case is analyzed to illustrate the power of the swap algebra formalism. More in general, we prove short time area-law bounds on average purity for...

  19. Integrated circuit authentication hardware Trojans and counterfeit detection

    CERN Document Server

    Tehranipoor, Mohammad; Zhang, Xuehui

    2013-01-01

    This book describes techniques to verify the authenticity of integrated circuits (ICs). It focuses on hardware Trojan detection and prevention and counterfeit detection and prevention. The authors discuss a variety of detection schemes and design methodologies for improving Trojan detection techniques, as well as various attempts at developing hardware Trojans in IP cores and ICs. While describing existing Trojan detection methods, the authors also analyze their effectiveness in disclosing various types of Trojans, and demonstrate several architecture-level solutions. 

  20. Different types of synchronization in coupled network based chaotic circuits

    Science.gov (United States)

    Srinivasan, K.; Chandrasekar, V. K.; Gladwin Pradeep, R.; Murali, K.; Lakshmanan, M.

    2016-10-01

    We propose a simple and new unified method to achieve lag, complete and anticipatory synchronizations in coupled nonlinear systems. It can be considered as an alternative to the subsystem and intentional parameter mismatch methods. This novel method is illustrated in a unidirectionally coupled RC phase shift network based Chua's circuit. Employing feedback coupling, different types of chaos synchronization are observed experimentally and numerically in coupled identical chaotic oscillators without using time delay. With a simple switch in the experimental set up we observe different kinds of synchronization. We also analyze the coupled system with numerical simulations.

  1. Power-Integrated Circuit Active Leakage Current Detector

    Directory of Open Access Journals (Sweden)

    M. F. Bulacio

    2012-01-01

    Full Text Available Most of the failures of induction motors become insulation faults, causing a permanent damage. Using differential current transformers, a system capable of insulation fault detection was developed, based on the differential relay protection scheme. Both signal injection and fault detection circuitry were integrated in a single chip. The proposed scheme is faster than other existing protection and not restricted to protect induction motors, but several other devices (such as IGBTs and systems. This paper explains the principle of operation of fault protection scheme and analyzes an integrated implementation through simulations and experimental results. A power-integrated circuit (PIC implementation is presented.

  2. Integrated circuit design using design automation

    International Nuclear Information System (INIS)

    Although the use of computer aids to develop integrated circuits is relatively new at Sandia, the program has been very successful. The results have verified the utility of the in-house CAD design capability. Custom IC's have been developed in much shorter times than available through semiconductor device manufacturers. In addition, security problems were minimized and a saving was realized in circuit cost. The custom CMOS IC's were designed at less than half the cost of designing with conventional techniques. In addition to the computer aided design, the prototype fabrication and testing capability provided by the semiconductor development laboratory and microelectronics computer network allows the circuits to be fabricated and evaluated before the designs are transferred to the commercial semiconductor manufacturers for production. The Sandia design and prototype fabrication facilities provide the capability of complete custom integrated circuit development entirely within the ERDA laboratories

  3. Analog Computation by DNA Strand Displacement Circuits.

    Science.gov (United States)

    Song, Tianqi; Garg, Sudhanshu; Mokhtar, Reem; Bui, Hieu; Reif, John

    2016-08-19

    DNA circuits have been widely used to develop biological computing devices because of their high programmability and versatility. Here, we propose an architecture for the systematic construction of DNA circuits for analog computation based on DNA strand displacement. The elementary gates in our architecture include addition, subtraction, and multiplication gates. The input and output of these gates are analog, which means that they are directly represented by the concentrations of the input and output DNA strands, respectively, without requiring a threshold for converting to Boolean signals. We provide detailed domain designs and kinetic simulations of the gates to demonstrate their expected performance. On the basis of these gates, we describe how DNA circuits to compute polynomial functions of inputs can be built. Using Taylor Series and Newton Iteration methods, functions beyond the scope of polynomials can also be computed by DNA circuits built upon our architecture. PMID:27363950

  4. Electromigration modeling at circuit layout level

    CERN Document Server

    Tan, Cher Ming

    2013-01-01

    Integrated circuit (IC) reliability is of increasing concern in present-day IC technology where the interconnect failures significantly increases the failure rate for ICs with decreasing interconnect dimension and increasing number of interconnect levels.  Electromigration (EM) of interconnects has now become the dominant failure mechanism that determines the circuit reliability. This brief addresses the readers to the necessity of 3D real circuit modelling in order to evaluate the EM of interconnect system in ICs, and how they can create such models for their own applications. A 3-dimensional (3D) electro-thermo-structural model as opposed to the conventional current density based 2-dimensional (2D) models is presented at circuit-layout level. 

  5. Signal conditioner circuit for photomultiplier tube

    Science.gov (United States)

    Cellier, A.; Hoover, W. M.

    1970-01-01

    Miniaturized circuit improves measurement of radiation dose absorbed in a scintillation crystal. The temperature coefficient of the field-effect transistor gate-source voltage in the isolation amplifier can be readily controlled.

  6. Constructing circuit codes by permuting initial sequences

    CERN Document Server

    Wynn, Ed

    2012-01-01

    Two new constructions are presented for coils and snakes in the hypercube. Improvements are made on the best known results for snake-in-the-box coils of dimensions 9, 10 and 11, and for some other circuit codes of dimensions between 8 and 13. In the first construction, circuit codes are generated from permuted copies of an initial transition sequence; the multiple copies constrain the search, so that long codes can be found relatively efficiently. In the second construction, two lower-dimensional paths are joined together with only one or two changes in the highest dimension; this requires a search for a permutation of the second sequence to fit around the first. It is possible to investigate sequences of vertices of the hypercube, including circuit codes, by connecting the corresponding vertices in an extended graph related to the hypercube. As an example of this, invertible circuit codes are briefly discussed.

  7. Arc modelling in SF6 circuit breakers

    International Nuclear Information System (INIS)

    The paper presents the work done by an operator, EDF and two manufacturers to improve the physical models and numerical methods used to simulate the behavior of the plasma and cold gas around it in a breaking chamber of the HV SF6 circuit breaker, during the high-current phase. This work concerns flow phenomena, in particular incorporating compressibility and the study of turbulence, the coupling between these flow phenomena and electromagnetic phenomena, and finally, radiation - which plays an essential role in energy transfer during the high-current phase. For this latter aspect, emission but also absorption were proven to play a major role, and the two were introduced into the models. The paper presents the models developed and the results obtained with them for simulation of two circuit breaker mock-ups (a double-pressure circuit breaker mock-up and a self-expanding and rotating arc circuit breaker mock-up). (author)

  8. Circuit reduces distortion of FM modulator

    Science.gov (United States)

    1965-01-01

    Correction circuit improves the linearity of a voltage-variable capacitor used to modulate a free-running oscillator. This improvement only applies to audio frequency modulation and will not correct for slowly varying dc input in some telemetry systems.

  9. Analog circuit for controlling acoustic transducer arrays

    Energy Technology Data Exchange (ETDEWEB)

    Drumheller, Douglas S. (Cedar Crest, NM)

    1991-01-01

    A simplified ananlog circuit is presented for controlling electromechanical transducer pairs in an acoustic telemetry system. The analog circuit of this invention comprises a single electrical resistor which replaces all of the digital components in a known digital circuit. In accordance with this invention, a first transducer in a transducer pair of array is driven in series with the resistor. The voltage drop across this resistor is then amplified and used to drive the second transducer. The voltage drop across the resistor is proportional and in phase with the current to the transducer. This current is approximately 90 degrees out of phase with the driving voltage to the transducer. This phase shift replaces the digital delay required by the digital control circuit of the prior art.

  10. The global atmospheric electrical circuit and climate

    CERN Document Server

    Harrison, R G

    2004-01-01

    Evidence is emerging for physical links among clouds, global temperatures, the global atmospheric electrical circuit and cosmic ray ionisation. The global circuit extends throughout the atmosphere from the planetary surface to the lower layers of the ionosphere. Cosmic rays are the principal source of atmospheric ions away from the continental boundary layer: the ions formed permit a vertical conduction current to flow in the fair weather part of the global circuit. Through the (inverse) solar modulation of cosmic rays, the resulting columnar ionisation changes may allow the global circuit to convey a solar influence to meteorological phenomena of the lower atmosphere. Electrical effects on non-thunderstorm clouds have been proposed to occur via the ion-assisted formation of ultrafine aerosol, which can grow to sizes able to act as cloud condensation nuclei, or through the increased ice nucleation capability of charged aerosols. Even small atmospheric electrical modulations on the aerosol size distribution ca...

  11. Combinatorics at Electronic Circuit Realization in FPAA

    Directory of Open Access Journals (Sweden)

    György Györök

    2009-03-01

    Full Text Available Our present work is to examine and offer an automatic electronic circuitconstruction solution which – using electronic devices and Field Programmable AnalogArrays (FPAA – enables us to form analogue circuits. The automatic computer-assistedconstruction is an old endeavor in the electronic development of electronic circuitconstructional tasks. The currently used constructional systems are integrated deviceswhich contain simulation modules based on circuit drawings and component parameters. Itis relevant in printed circuit construction as well, where wiring geometry can be modifieddepending on the examined (EMC, thermo-technical, transmissionldots, etc. parameters.To achieve this goal, new simulation and circuit generation processes are required, whichselect the most appropriate solutions regarding the parametrical description of electronictopology.

  12. Developing a Domain Model for Relay Circuits

    DEFF Research Database (Denmark)

    Haxthausen, Anne Elisabeth

    2009-01-01

    In this paper we stepwise develop a domain model for relay circuits as used in railway control systems. First we provide an abstract, property-oriented model of networks consisting of components that can be glued together with connectors. This model is strongly inspired by a network model for...... railways madeby Bjørner et.al., however our model is more general: the components can be of any kind and can later be refined to e.g. railway components or circuit components. Then we show how the abstract network model can be refined into an explicit model for relay circuits. The circuit model describes...... defined, checked to be legal, and the reaction to an input can be simulated....

  13. Lateral power transistors in integrated circuits

    CERN Document Server

    Erlbacher, Tobias

    2014-01-01

    This book details and compares recent advancements in the development of novel lateral power transistors (LDMOS devices) for integrated circuits in power electronic applications. It includes the state-of-the-art concept of double-acting RESURF topologies.

  14. Energy saving dc-dc converter circuit

    International Nuclear Information System (INIS)

    An energy saving dc-dc converter circuit is disclosed having two energy efficient means which operate in tandem, an energy conserving means and a voltage doubling means. These energy efficient means are applied in combination with elements commonly found in dc-dc converter circuits, namely an ac voltage generator, a transformer for stepping up the generated ac voltage, and means for storing the converted dc voltage. The energy conserving means is connected to the dc voltage storage means. It comprises a resettable inhibit circuit which cuts off the provision of dc voltage for conversion for a predetermined interval when the output of the converter exceeds a predetermined level. The voltage doubling means is reponsive to outputs of the inhibit circuit of the energy conserving means and the ac voltage generator. It provides a phase inverted waveform of the generated ac voltage on one of two leads to the ac voltage step-up transformer

  15. On equivalent resistance of electrical circuits

    CERN Document Server

    Kagan, Mikhail

    2015-01-01

    While the standard (introductory physics) way of computing the equvalent resistance of non-trivial electrical ciruits is based on Kirchhoff's rules, there is a mathematically and conceptually simpler approach, called the method of nodal potentials, whose basic variables are the values of electric potential at the circuit's nodes. In this paper, we review the method of nodal potentials and illustrate it using the Wheatstone bridge as an example. At the end, we derive - in a closed form - the equivalent resistance of a generic circuit, which we apply to a few sample circuits. The final result unveils a curious interplay between electrical circuits, matrix algebra, and graph theory and its applications to computer science. The paper is written at a level accessible by undergraduate students who are familiar with matrix arithmetic. For the more inquisitive reader, additional proofs and technical details are provided in the appendix.

  16. LC Quadrature Generation in Integrated Circuits

    DEFF Research Database (Denmark)

    Christensen, Kåre Tais

    2001-01-01

    Today quadrature signals for IQ demodulation are provided through RC polyphase networks, quadrature oscillators or double frequency VCOs. This paper presents a new method for generating quadrature signals in integrated circuits using only inductors and capacitors. This LC quadrature generation...

  17. Polynomial threshold functions and Boolean threshold circuits

    DEFF Research Database (Denmark)

    Hansen, Kristoffer Arnsfelt; Podolskii, Vladimir V.

    2013-01-01

    secondary interest. We show that PTFs on general Boolean domains are tightly connected to depth two threshold circuits. Our main results in regard to this connection are: PTFs of polynomial length and polynomial degree compute exactly the functions computed by THRMAJ circuits. An exponential length lower...... bound for PTFs that holds regardless of degree, thereby extending known lower bounds for THRMAJ circuits. We generalize two-party unbounded error communication complexity to the multi-party number-on-the-forehead setting, and show that communication lower bounds for 3-player protocols would yield size...... lower bounds for THRTHR circuits. We obtain several other results about PTFs. These include relationships between weight and degree of PTFs, and a degree lower bound for PTFs of constant length. We also consider a variant of PTFs over the max-plus algebra. We show that they are connected to PTFs over...

  18. Understanding the behaviour of infinite ladder circuits

    International Nuclear Information System (INIS)

    Infinite ladder circuits are often encountered in undergraduate electrical engineering and physics curricula when dealing with series and parallel combination of impedances, as a part of filter design or wave propagation on transmission lines. The input impedance of such infinite ladder circuits is derived by assuming that the input impedance does not change when a new block of impedance is added. However, the impedance derived from this assumption may lead to incorrect conclusions if it is not treated carefully. Sometimes, in the literature, the input impedance behaviour of infinite ladder circuits is referred to as a paradox, leaving students and educators in doubt. This study intends to clarify this confusion and help to better comprehend the behaviour of the input impedance of infinite ladder circuits

  19. Magnetic Logic Circuits for Extreme Environments Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The program aims to demonstrate a new genre of all-magnetic logic circuits which are radiation-tolerant and capable of reliable operation in extreme environmental...

  20. Density Matrix for Mesoscopic Distributed Parameter Circuits

    Institute of Scientific and Technical Information of China (English)

    JI Ying-Hua; WANG Qi; LUO Hai-Mei; LEI Min-Sheng

    2005-01-01

    Under the Born-von-Karmann periodic boundary condition, we propose a quantization scheme for nondissipative distributed parameter circuits (i.e. a uniform periodic transmission line). We find the unitary operator for diagonalizing the Hamiltonian of the uniform periodic transmission line. The unitary operator is expressed in a coordinate representation that brings convenience to deriving the density matrix p(q, q',β). The quantum fluctuations of charge and current at a definite temperature have been studied. It is shown that quantum fluctuations of distributed parameter circuits, which also have distributed properties, are related to both the circuit parameters and the positions and the mode of signals and temperature T. The higher the temperature is, the stronger quantum noise the circuit exhibits.

  1. Managing healthcare information: analyzing trust.

    Science.gov (United States)

    Söderström, Eva; Eriksson, Nomie; Åhlfeldt, Rose-Mharie

    2016-08-01

    Purpose - The purpose of this paper is to analyze two case studies with a trust matrix tool, to identify trust issues related to electronic health records. Design/methodology/approach - A qualitative research approach is applied using two case studies. The data analysis of these studies generated a problem list, which was mapped to a trust matrix. Findings - Results demonstrate flaws in current practices and point to achieving balance between organizational, person and technology trust perspectives. The analysis revealed three challenge areas, to: achieve higher trust in patient-focussed healthcare; improve communication between patients and healthcare professionals; and establish clear terminology. By taking trust into account, a more holistic perspective on healthcare can be achieved, where trust can be obtained and optimized. Research limitations/implications - A trust matrix is tested and shown to identify trust problems on different levels and relating to trusting beliefs. Future research should elaborate and more fully address issues within three identified challenge areas. Practical implications - The trust matrix's usefulness as a tool for organizations to analyze trust problems and issues is demonstrated. Originality/value - Healthcare trust issues are captured to a greater extent and from previously unchartered perspectives. PMID:27477934

  2. COBSTRAN - COMPOSITE BLADE STRUCTURAL ANALYZER

    Science.gov (United States)

    Aiello, R. A.

    1994-01-01

    The COBSTRAN (COmposite Blade STRuctural ANalyzer) program is a pre- and post-processor that facilitates the design and analysis of composite turbofan and turboprop blades, as well as composite wind turbine blades. COBSTRAN combines composite mechanics and laminate theory with a data base of fiber and matrix properties. As a preprocessor for NASTRAN or another Finite Element Method (FEM) program, COBSTRAN generates an FEM model with anisotropic homogeneous material properties. Stress output from the FEM program is provided as input to the COBSTRAN postprocessor. The postprocessor then uses the composite mechanics and laminate theory routines to calculate individual ply stresses, strains, interply stresses, thru-the-thickness stresses and failure margins. COBSTRAN is designed to carry out the many linear analyses required to efficiently model and analyze blade-like structural components made of multilayered angle-plied fiber composites. Components made from isotropic or anisotropic homogeneous materials can also be modeled as a special case of COBSTRAN. NASTRAN MAT1 or MAT2 material cards are generated according to user supplied properties. COBSTRAN is written in FORTRAN 77 and was implemented on a CRAY X-MP with a UNICOS 5.0.12 operating system. The program requires either COSMIC NASTRAN or MSC NASTRAN as a structural analysis package. COBSTRAN was developed in 1989, and has a memory requirement of 262,066 64 bit words.

  3. Dynamical Systems in Circuit Designer's Eyes

    Energy Technology Data Exchange (ETDEWEB)

    Odyniec, M.

    2011-05-09

    Examples of nonlinear circuit design are given. Focus of the design process is on theory and engineering methods (as opposed to numerical analysis). Modeling is related to measurements It is seen that the phase plane is still very useful with proper models Harmonic balance/describing function offers powerful insight (via the combination of simulation with circuit and ODE theory). Measurement and simulation capabilities increased, especially harmonics measurements (since sinusoids are easy to generate)

  4. Combinatorics of Boolean automata circuits dynamics

    OpenAIRE

    Demongeot, Jacques; Noual, Mathilde; Sené, Sylvain

    2012-01-01

    International audience In line with fields of theoretical computer science and biology that study Boolean automata networks to model regulation networks, we present some results concerning the dynamics of networks whose underlying structures are oriented cycles, that is, Boolean automata circuits. In the context of biological regulation, former studies have highlighted the importance of circuits on the asymptotic dynamical behaviour of the biological networks that contain them. Our work fo...

  5. Automatic Design of Digital Synthetic Gene Circuits

    OpenAIRE

    Marchisio, Mario A.; Jörg Stelling

    2011-01-01

    Author Summary Synthetic Biology is a novel discipline that aims at the construction of new biological systems able to perform specific tasks. Following the example of electrical engineering, most of the synthetic systems so far realized look like circuits where smaller DNA-encoded components are interconnected by the exchange of different kinds of molecules. According to this modular approach, we developed, in a previous work, a tool for the visual design of new genetic circuits whose compon...

  6. Light-Controlled Synthetic Gene Circuits

    OpenAIRE

    Gardner, Laura; Deiters, Alexander

    2012-01-01

    Highly complex synthetic gene circuits have been engineered in living organisms to develop systems with new biological properties. A precise trigger to activate or deactivate these complex systems is desired in order to tightly control different parts of a synthetic or natural network. Light represents an excellent tool to achieve this goal as it can be regulated in timing, location, intensity, and wavelength, which allows for precise spatiotemporal control over genetic circuits. Recently, li...

  7. Dynamics of gene circuits shapes evolvability

    OpenAIRE

    Jim??nez, Alba; Cotterell, James; Munteanu, Andreea; Sharpe, James

    2015-01-01

    To what extent does the dynamical mechanism producing a specific biological phenotype bias the ability to evolve into novel phenotypes? We use the interpretation of a morphogen gradient into a single stripe of gene expression as a model phenotype. Although there are thousands of three-gene circuit topologies that can robustly develop a stripe of gene expression, the vast majority of these circuits use one of just six fundamentally different dynamical mechanisms. Here we explore the potential ...

  8. Latent phenotypes pervade gene regulatory circuits

    OpenAIRE

    Payne, Joshua L.; Wagner, Andreas

    2014-01-01

    Background Latent phenotypes are non-adaptive byproducts of adaptive phenotypes. They exist in biological systems as different as promiscuous enzymes and genome-scale metabolic reaction networks, and can give rise to evolutionary adaptations and innovations. We know little about their prevalence in the gene expression phenotypes of regulatory circuits, important sources of evolutionary innovations. Results Here, we study a space of more than sixteen million three-gene model regulatory circuit...

  9. Computational Aspects of Feedback in Neural Circuits

    OpenAIRE

    Wolfgang Maass; Prashant Joshi; Sontag, Eduardo D.

    2007-01-01

    It has previously been shown that generic cortical microcircuit models can perform complex real-time computations on continuous input streams, provided that these computations can be carried out with a rapidly fading memory. We investigate the computational capability of such circuits in the more realistic case where not only readout neurons, but in addition a few neurons within the circuit, have been trained for specific tasks. This is essentially equivalent to the case where the output of t...

  10. Solution methods for very highly integrated circuits.

    Energy Technology Data Exchange (ETDEWEB)

    Nong, Ryan; Thornquist, Heidi K.; Chen, Yao; Mei, Ting; Santarelli, Keith R.; Tuminaro, Raymond Stephen

    2010-12-01

    While advances in manufacturing enable the fabrication of integrated circuits containing tens-to-hundreds of millions of devices, the time-sensitive modeling and simulation necessary to design these circuits poses a significant computational challenge. This is especially true for mixed-signal integrated circuits where detailed performance analyses are necessary for the individual analog/digital circuit components as well as the full system. When the integrated circuit has millions of devices, performing a full system simulation is practically infeasible using currently available Electrical Design Automation (EDA) tools. The principal reason for this is the time required for the nonlinear solver to compute the solutions of large linearized systems during the simulation of these circuits. The research presented in this report aims to address the computational difficulties introduced by these large linearized systems by using Model Order Reduction (MOR) to (i) generate specialized preconditioners that accelerate the computation of the linear system solution and (ii) reduce the overall dynamical system size. MOR techniques attempt to produce macromodels that capture the desired input-output behavior of larger dynamical systems and enable substantial speedups in simulation time. Several MOR techniques that have been developed under the LDRD on 'Solution Methods for Very Highly Integrated Circuits' will be presented in this report. Among those presented are techniques for linear time-invariant dynamical systems that either extend current approaches or improve the time-domain performance of the reduced model using novel error bounds and a new approach for linear time-varying dynamical systems that guarantees dimension reduction, which has not been proven before. Progress on preconditioning power grid systems using multi-grid techniques will be presented as well as a framework for delivering MOR techniques to the user community using Trilinos and the Xyce circuit

  11. Effects of smoke on functional circuits

    International Nuclear Information System (INIS)

    Nuclear power plants are converting to digital instrumentation and control systems; however, the effects of abnormal environments such as fire and smoke on such systems are not known. There are no standard tests for smoke, but previous smoke exposure tests at Sandia National Laboratories have shown that digital communications can be temporarily interrupted during a smoke exposure. Another concern is the long-term corrosion of metals exposed to the acidic gases produced by a cable fire. This report documents measurements of basic functional circuits during and up to 1 day after exposure to smoke created by burning cable insulation. Printed wiring boards were exposed to the smoke in an enclosed chamber for 1 hour. For high-resistance circuits, the smoke lowered the resistance of the surface of the board and caused the circuits to short during the exposure. These circuits recovered after the smoke was vented. For low-resistance circuits, the smoke caused their resistance to increase slightly. A polyurethane conformal coating substantially reduced the effects of smoke. A high-speed digital circuit was unaffected. A second experiment on different logic chip technologies showed that the critical shunt resistance that would cause failure was dependent on the chip technology and that the components used in the smoke exposures were some of the most smoke tolerant. The smoke densities in these tests were high enough to cause changes in high impedance (resistance) circuits during exposure, but did not affect most of the other circuits. Conformal coatings and the characteristics of chip technologies should be considered when designing circuitry for nuclear power plant safety systems, which must be highly reliable under a variety of operating and accident conditions. 10 refs., 34 figs., 18 tabs

  12. From circuits to behaviour in the amygdala.

    Science.gov (United States)

    Janak, Patricia H; Tye, Kay M

    2015-01-15

    The amygdala has long been associated with emotion and motivation, playing an essential part in processing both fearful and rewarding environmental stimuli. How can a single structure be crucial for such different functions? With recent technological advances that allow for causal investigations of specific neural circuit elements, we can now begin to map the complex anatomical connections of the amygdala onto behavioural function. Understanding how the amygdala contributes to a wide array of behaviours requires the study of distinct amygdala circuits. PMID:25592533

  13. Fully CMOS Memristor Based Chaotic Circuit

    OpenAIRE

    Yener, S. C.; H. H. Kuntman

    2014-01-01

    This paper demonstrates the design of a fully CMOS chaotic circuit consisting of only DDCC based memristor and inductance simulator. Our design is composed of these active blocks using CMOS 0.18 µm process technology with symmetric ±1.25 V supply voltages. A new single DDCC+ based topology is used as the inductance simulator. Simulation results verify that the design proposed satisfies both memristor properties and the chaotic behavior of the circuit. Simulations performed illustrate the succ...

  14. Striatal plasticity and basal ganglia circuit function

    OpenAIRE

    Kreitzer, Anatol C.; Malenka, Robert C.

    2008-01-01

    The dorsal striatum, which consists of the caudate and putamen, is the gateway to the basal ganglia. It receives convergent excitatory afferents from cortex and thalamus and forms the origin of the direct and indirect pathways—distinct basal ganglia circuits involved in motor control. It is also a major site of activity-dependent synaptic plasticity. Striatal plasticity alters the transfer of information throughout basal ganglia circuits and may represent a key neural substrate for adaptive m...

  15. Evolvable designs of experiments applications for circuits

    CERN Document Server

    Iordache, Octavian

    2009-01-01

    Adopting a groundbreaking approach, the highly regarded author shows how to design methods for planning increasingly complex experiments. He begins with a brief introduction to standard quality methods and the technology in standard electric circuits. The book then gives numerous examples of how to apply the proposed methodology in a series of real-life case studies. Although these case studies are taken from the printed circuit board industry, the methods are equally applicable to other fields of engineering.

  16. Fractal Electronic Circuits Assembled From Nanoclusters

    Science.gov (United States)

    Fairbanks, M. S.; McCarthy, D.; Taylor, R. P.; Brown, S. A.

    2009-07-01

    Many patterns in nature can be described using fractal geometry. The effect of this fractal character is an array of properties that can include high internal connectivity, high dispersivity, and enhanced surface area to volume ratios. These properties are often desirable in applications and, consequently, fractal geometry is increasingly employed in technologies ranging from antenna to storm barriers. In this paper, we explore the application of fractal geometry to electrical circuits, inspired by the pervasive fractal structure of neurons in the brain. We show that, under appropriate growth conditions, nanoclusters of Sb form into islands on atomically flat substrates via a process close to diffusion-limited aggregation (DLA), establishing fractal islands that will form the basis of our fractal circuits. We perform fractal analysis of the islands to determine the spatial scaling properties (characterized by the fractal dimension, D) of the proposed circuits and demonstrate how varying growth conditions can affect D. We discuss fabrication approaches for establishing electrical contact to the fractal islands. Finally, we present fractal circuit simulations, which show that the fractal character of the circuit translates into novel, non-linear conduction properties determined by the circuit's D value.

  17. A Simple Memristor Model for Circuit Simulations

    Science.gov (United States)

    Fullerton, Farrah-Amoy; Joe, Aaleyah; Gergel-Hackett, Nadine; Department of Chemistry; Physics Team

    This work describes the development of a model for the memristor, a novel nanoelectronic technology. The model was designed to replicate the real-world electrical characteristics of previously fabricated memristor devices, but was constructed with basic circuit elements using a free widely available circuit simulator, LT Spice. The modeled memrsistors were then used to construct a circuit that performs material implication. Material implication is a digital logic that can be used to perform all of the same basic functions as traditional CMOS gates, but with fewer nanoelectronic devices. This memristor-based digital logic could enable memristors' use in new paradigms of computer architecture with advantages in size, speed, and power over traditional computing circuits. Additionally, the ability to model the real-world electrical characteristics of memristors in a free circuit simulator using its standard library of elements could enable not only the development of memristor material implication, but also the development of a virtually unlimited array of other memristor-based circuits.

  18. Hysteresis in a quantized superfluid 'atomtronic' circuit.

    Science.gov (United States)

    Eckel, Stephen; Lee, Jeffrey G; Jendrzejewski, Fred; Murray, Noel; Clark, Charles W; Lobb, Christopher J; Phillips, William D; Edwards, Mark; Campbell, Gretchen K

    2014-02-13

    Atomtronics is an emerging interdisciplinary field that seeks to develop new functional methods by creating devices and circuits where ultracold atoms, often superfluids, have a role analogous to that of electrons in electronics. Hysteresis is widely used in electronic circuits-it is routinely observed in superconducting circuits and is essential in radio-frequency superconducting quantum interference devices. Furthermore, it is as fundamental to superfluidity (and superconductivity) as quantized persistent currents, critical velocity and Josephson effects. Nevertheless, despite multiple theoretical predictions, hysteresis has not been previously observed in any superfluid, atomic-gas Bose-Einstein condensate. Here we directly detect hysteresis between quantized circulation states in an atomtronic circuit formed from a ring of superfluid Bose-Einstein condensate obstructed by a rotating weak link (a region of low atomic density). This contrasts with previous experiments on superfluid liquid helium where hysteresis was observed directly in systems in which the quantization of flow could not be observed, and indirectly in systems that showed quantized flow. Our techniques allow us to tune the size of the hysteresis loop and to consider the fundamental excitations that accompany hysteresis. The results suggest that the relevant excitations involved in hysteresis are vortices, and indicate that dissipation has an important role in the dynamics. Controlled hysteresis in atomtronic circuits may prove to be a crucial feature for the development of practical devices, just as it has in electronic circuits such as memories, digital noise filters (for example Schmitt triggers) and magnetometers (for example superconducting quantum interference devices).

  19. Development of a pocket multi-channel analyzer

    International Nuclear Information System (INIS)

    A pocket Multi-Channel Analyzer, which is based on 20 pin SMT micro-controller, Serial Peripheral Interfaced ADC and FRAM, and MCU on chip timer/counter acting as de-dead-time clock, was developed and introduced in this paper. Pulse peak hold circuit, MCA timing, micro-controller application techniques, and a reliable simple schematic for peak detection was described as well. The protocol MCA is housed in 110 60 23 mm3. The analyzing resolution can be up to 16384 channels. The dead time is 17 μs when the resolution is programmed to be 1024 channels. It is powered from a single +5V supply, and the power consumption is 360 mW. It can be well embedded in various portable multi-channel spectrum equipments. (authors)

  20. Modeling of the Voltage Waves in the LHC Main Dipole Circuits

    CERN Document Server

    Ravaioli, E; Formenti, F; Steckert, J; Thiesen, H; Verweij, A

    2012-01-01

    When a fast power abort is triggered in the LHC main dipole chain, voltage transients are generated at the output of the power converter and across the energy-extraction switches. The voltage waves propagate through the chain of 154 superconducting dipoles and can have undesired effects leading to spurious triggering of the quench protection system and firing of the quench heaters. The phase velocity of the waves travelling along the chain changes due to the inhomogeneous AC behavior of the dipoles. Furthermore, complex phenomena of reflection and superposition are present in the circuit. For these reasons analytical calculations are not sufficient for properly analyzing the circuit behavior after a fast power abort. The transients following the switch-off of the power converter and the opening of the switches are analyzed by means of a complete electrical model, developed with the Cadence© suite (PSpice© based). The model comprises all the electrical components of the circuit, additional components simula...