WorldWideScience

Sample records for chugoku ni okeru

  1. Preventive measures of water pollution in China; Chugoku ni okeru suishitsu odaku boshi taisaku

    Energy Technology Data Exchange (ETDEWEB)

    Qian, Y.; Huang, X.

    1996-01-10

    This paper describes the progress and the major results of research and development on technologies and measures to prevent water pollution in China. Tests and researches have been performed on an upward anaerobic sludge blanket (UASB), a vertical baffled anaerobic sludge blanket, two-phase anaerobic digestion, and an anaerobic fluidized bed. When anaerobically digested sludge and aerobic active sludge are inoculated in the UASB, particle-shaped sludge was formed well in both sludges. This technology has begun to be used in breweries and citric acid factories. With anaerobic treatment of waste water containing sulfate, the sulfate was recovered as sulfur by using the first and second phases. Research and development is being progressed on the oxidation ditch technology as an improved version of the active sludge method. In a pilot test of a soil treatment system and a stabilization pond treatment system as alternative technology for the active sludge method, the BOD in the treated water was found 2.5 mg{times}1/l. Attentions are drawn on primary treatment, a living organism contact oxidation method, and a continuous filtration treatment process as technologies to turn polluted water into resources. 6 refs., 1 tab.

  2. Survey of Joint Implementation activities in China; Chugoku ni okeru kyodo jisshi katsudo kanren chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    It is a large task for Japan to positively promote the Joint Implementation activities related to the United Nations Framework Convention on Climate Change. Rapid increase in the emission of greenhouse-effect gases, especially CO2, is predicted in China with remarkable economic growth and population of 1.2 billion. It is essential to promote the Joint Implementation activities in China. In this survey, framework, organization, problems and tasks were investigated to effectively promote the Joint Implementation activities in China. Construction of framework for the real Joint Implementation activities has been proposed. Current problems for promoting the Joint Implementation activities in China are that the distinct guideline for the Joint Implementation is not established in the government, that the receiving system including receiving, planning and arranging sections is not established, and that the burden problems for the costs of project evaluation, data acquisition, monitoring, and verification are not solved. 5 refs., 21 figs., 6 tabs.

  3. Research report for fiscal 1998. Promotion of activities implemented jointly etc. in China; 1998 nendo Chugoku ni okeru kyodo jisshi katsudo nado suishin chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The Kyoto Protocol allows some flexibility in the implementation of methods for achieving the goal, such as emission trading, activities implemented jointly (AIJ) among advanced countries, construction of clean development mechanisms (CDM) with developing countries, etc., and Japan intends to positively make use of them for the achievement of the goal. For China, who holds second place in the list of greenhouse gas emitting countries in the world, the promotion of CDM is quite important. With the situation taken into consideration, interaction was effected with Chinese officers and scientists of government agencies and academic institutes involved in environmental matters, and researches were conducted. Views and information were exchanged regarding environmental problems and, after on-site investigations, researches were conducted and suggestions were presented as to how AIJ and CDM should be. The suggestions covered Chinese policies toward AIJ and CDM, current state of AIJ projects in China and systems for their promotion, means for enhancing such projects, and discovery of candidates for AIJ and CDM project application. (NEDO)

  4. Combined process of pyrolyzer/combuster for gas production and power generation; Chugoku ni okeru chukibo hatsuden to toshi gas seizo no tame no fukugo process no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Ooka, I. [The University of Tokushima, Tokushima (Japan); Ma, T.

    1997-10-30

    In China, they are using a lot of coal by direct firing for domestic cooking, space heating and industrial use. Therefore air pollution is the big problem in every cities in winter season. And at moment, they do not have enough infrastructure for supplying energy such as gas and electric power. There is a great need for facilities for supplying gas and electric power from coal in big cities with much less pollution. This paper d a combined process of medium size plant of gas production and power generation by using fluidized circulation bed pyrolizer and combuster, to contribute to the energy supply which greatly reduces air and water polution and coal consumption. 1 ref., 1 fig., 3 tabs.

  5. FY 1998 annual report on power generation by waste heat from cement production in China; Chugoku ni okeru cement hainetsu hatsuden 1998 nendo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project is to implement a feasibility study for applying waste heat power generation, which have been already commercialized in Japan and producing remarkable results, to China's cement plants producing 3,500 t/d or more of clinker, and thereby to try to establish a link with the Japan's clean development mechanism. It is expected that introduction of these systems improves energy use efficiency and environments in China. The study results indicate that the project for a Tongling Conch plant could generate power of 15,000 kW, reducing CO2 emissions by 89,178 t/y and cumulatively 1,783,560 tons in the 20-year period. The results also indicate that the project will be highly profitable, with an estimated internal return rate of as high as 33.78%. The project for a Huaxin plant could generate power of 8,400 kW, reducing CO2 emissions by 48,412 t/y and cumulatively 968,240 tons in the 20-year period, annually saving power charges by 325 million yen and bringing an internal return rate of 10.72%. (NEDO)

  6. Report on survey of promotion of activities implemented jointly in China in FY 1997; 1997 nendo chosa hokokusho (Chugoku ni okeru kyodo jisshi katsudo no suishin chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Rapid economy growth has been observed in Asia including Japan. On the other hand, problems of population and environment grew even worse with the economic growth. Especially, China is the second CO2 emission country in the world. Large energy demand is still forecasted with its economic growth in the future. It is well-known that the energy consumption per unit GDP is very large. Therefore, it is very significant to promote the activities implemented jointly with China for mitigating the emission of greenhouse gases including CO2, which provides a significant meaning for solving global environmental issues as well as for improving regional environmental issues. It is necessary for the above to recognize the appropriate current situations and to promote the activities implemented jointly suitable for the country. Based on the discussions and information exchanges about environmental issues with staffs concerning environmental policies and scientists as well as the field surveys, methods for the activities implemented jointly were investigated to provide some proposals. 4 figs., 8 tabs.

  7. Preliminary research on the activities implemented jointly (AIJ) workshop. Present AIJ in China; Kyodo jisshi katsudo workshop ni kansuru jizen chosa. Chugoku ni okeru kyodo jisshi katsudo no genjo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    In order to positively promote the activities implemented jointly (AIJ) of the United Nations Framework Convention on Climate Change, the AIJ workshop acting in contact with Asia/Pacific countries, in particular, Chine having large effect on global environmental pollution was researched preliminarily. AIJ approved in the convention is the effective means to promote measures against global warming cost-effectively by optimally combining every developed country`s technology, know-how and fund. Distribution of the credit for greenhouse gas emission reduction by AIJ is unsolved because of the disagreement of views between developed and developing countries. The pilot phase of AIJ projects is carried out by voluntary workers jointly with developing countries until establishment of international rules. In fiscal 1995, the following were studied: the framework necessary for AIJ between Japan and China, the organization for promoting concrete AIJ projects, and the means to create the reliance of China for AIJ projects. 6 refs., 10 figs.

  8. Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Survey by region/industry in China; Kankyo chowagata sekitan riyo system kanosei chosa. Chugoku ni okeru chiiki/sangyobetsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of establishing a coal utilization system which is environmentally friendly and effective, a survey had already been conducted jointly with China on the introduction of an environmentally friendly type coal utilization system, and a master plan for the whole China had been worked out. To make the results of the master plan more widely spread, this survey aimed in a 2-year plan at diagnosing coal utilization technology of the plants selected from each industry in the specified region and at making individual and concrete guidelines for the introduction of technology on CCT for engineers at sites and persons concerned with local administration. In the first fiscal year, a survey was made on coal production/utilization and the environmental situation in Henan Province for survey. Moreover, two plans each were selected as model plant from the chemical industry and construction material industry which are main industries in the said region to survey the present situation of coal utilization technology and measures for environmental protection. Based on the survey, more effective and more environmentally adaptable measures were also studied. 67 figs., 24 tabs.

  9. Catalytic technology in the energy/environment field. Utilization of catalyst in coal pyrolysis and gasification processes; Energy kankyo bun`ya ni okeru shokubai gijutsu. Sekitan no netsubunkai oyobi gas ka ni okeru shokubai no riyo

    Energy Technology Data Exchange (ETDEWEB)

    Otsuka, Y. [Tohoku University, Institute for Chemical Reaction Science (Japan)

    1998-05-20

    This review article focuses on the utilization of several catalysts during coal pyrolysis and gasification. In situ or off line catalytic upgrading of volatile matters during pyrolysis of low rank coals is carried out in pressurized H2 with different reactors to produce BTX (benzene, toluene and xylene). When NiSO4 and Ni(OH)2 are used in the hydropyrolysis of Australian brown coal using an entrained bed reactor with two separated reaction zones, BTX yield reaches 18-23%. MS-13X zeolite and USY zeolite mixed with Al2O3 are effective for producing BTX with powder-particle fluidized bed and two-stage reactors, respectively. Catalytic gasification is described from a standpoint of direct production of SNG(CH4) from coal and steam. When K2CO3 and Ni are compared for this purpose, Ni catalyst is more suitable at low temperatures of 500-600degC, where CH4 formation is thermodynamically favorable. Fe and Ca catalysts can successfully be prepared from inexpensive raw materials and are rather active for steam gasification at {>=}700degC. The use of upgrading and gasification catalysts is discussed in terms of preparation, performance, life and recovery. 27 refs., 6 figs., 2 tabs.

  10. Improvement of magnetic properties of Fe-50mass%Ni in MIM process; MIM process ni okeru Fe-50mass%Ni no jiki tokusei kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Miura, H. [Kumamoto University, Kumamoto (Japan). Faculty of Engineering; Fujita, S. [Kumamoto University, Kumamoto (Japan); Fujita, M.; Ninomiya, R. [Mitsuikinzoku Co. Ltd., Tokyo (Japan)

    2000-12-15

    Metal injection molding (MIM) process is hoped to be one of processing for required to more complicated parts of magnetic components. In this study, the effect of different types of powders (prealloyed and mixed elemental powders) on the magnetic properties of permalloy (Fe-50mass%Ni) through the MIM technique was investigated. Approximately 94% of theoretical density was obtained by using the prealloyed powder, and the retained carbon and oxygen contents were controlled to be low. On the other hand, 96% of theoretical density was obtained by using the mixed elemental powder, but the magnetic properties were inferior to that of prealloyed powder's because of high retained oxygen content. By using the carbonyl Fe powder with high carbon, the retained oxygen and carbon content could be controlled to be low, resulting in the improved magnetic properties. (author)

  11. Preferential dissolution behavior of copper-nickel alloys in neutral ammonium acetate solution; Chusei sakusan ammonium yoekichu ni okeru Cu-Ni gokin no yusen yokai kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Nishimura, R.; Yamakawa, K. [Osaka Univ. (Japan). Faculty of Engineering

    1997-11-15

    The electrochemical behaviors of copper alloys which show corrosion resistance under ocean circumstances were investigated in acid, neutral chlorides and a sulfate solution from the view point of preferential dissolution like dezincification corrosion. In this study, dissolved ion seeds of copper-nickel (10 to 42%) alloys in a neutral ammonium acetate solution are analyzed by the method of multi-elements simultaneous analysis using an ICP spectrophotometer, the preferential dissolution behavior of the copper-nickel alloys was studied through film formation analyzed by an AES (Auger Electron Spectroscope) and an anode oxidation current decrease with the increase of the Ni content, In regard to the contents of the dissolved ion seeds, the preferential dissolution of the Ni occurs independent from the Ni content in the active region, but in the passive region, only Cu-10%Ni alloy shows the Ni preferential dissolution in the low voltage side and shows the Cu preferential dissolution in the high voltage side. However, while the Ni content increase more, the Ni preferential dissolution occurs not depending on the voltage. 18 refs., 10 figs., 2 tabs.

  12. Fiscal 1995 survey report on the feasibility study of the environmentally friendly type coal utilization system. Survey on the environmentally friendly type coal utilization system in the coal preparation sector in China; Kankyo chowagata sekitan riyo system kanosei chosa. Chugoku no sentan bumon ni okeru kankyo chowagata sekitan riyo system ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    Specifying the coal preparation technology among clean coal technologies (CCT) in China, the paper investigated governmental policies, plans, standards of coal preparation technology, subjects, etc. toward the introduction/spread of coal preparation technology, and studied decision, introduction and spread of the coal preparation system suitable for the coal utilization status in China. The survey was conducted in Shanxi and Henan Provinces which are main provinces of coal production, and field survey was made at some selected coal preparation plants having different operational conditions. In the field survey, problems on the operation were extracted, and points of improvement were studied at the same time. Further, to grasp the positioning of coal preparation in CCT in China, survey was carried out on laws and regulation on coal preparation in terms of energy and environmental policies. Finally, the result of the field survey was analyzed, a coal preparation system of which the introduction/spread in medium- and long-term are enabled was proposed considering the coal utilization status and economic situation in China, and how to introduce/spread it was studied. 35 figs., 42 tabs.

  13. Application of new analytical techniques to the order-disorder transformation in Ni-Mo alloys; Ni-Mo gokin no kisoku-fukisoku hentai ni okeru atarashii kozo kaiseki no kokoromi

    Energy Technology Data Exchange (ETDEWEB)

    Oki, K.; Hata, S.; Kuwano, N. [Kyushu University, Fukuoka (Japan)

    1997-09-20

    This paper presents the analytical example of the ordering process of order-disorder transformation in Ni-Mo alloy using recent experimental techniques. Monte Carlo simulation clarified the fact that the ordering process in Ni4-Mo alloy is largely affected by short range interaction in the early stage of ordering, and forms D1a, D022 and Pt2Mo structure units with a similar atomic pair correlation. The ordering process is largely affected by long range interaction with an advance of ordering, and develops only D1a structure most stable in energy. In order to check the existence of SRO (short range order) structure obtained by Monte Carlo simulation, the analysis of high-resolution TEM images under SRO condition was carried out using the imaging plate recently developed for TEM. The analytical result showed that the observed N2M3 pattern is derived from not always the existence of N2M3 structure but superimposition of D1a, D022 and Pt2Mo structure units. 19 refs., 4 figs.

  14. FY 1995 report of feasibility study of a model project on energy saving equipment for Fe-alloy electric furnaces in China. Independent theme survey of rationalization of energy consumption; 1995 nendo chosa hokokusho Chugoku no gokintetsu denkiro ni okeru sho energy ka setsubi model jigyo jisshi kanosei chosa. Energy shiyo gorika taisaku kobetsu tema chosa jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-01

    A feasibility study of a model project was conducted on energy conservation and introduction of technology against pollution for Fe-alloy electric furnaces in China. The total production of Fe-alloy was 4.32 million tons in 1995, which recorded the maximum production. Out of which ferro-Cr occupied 9.5%. Production of high carbon ferro-Cr in 2000 is estimated to be 600,000 tons. China`s electric furnaces for ferro-Cr using carbon as heat source do not have covers and gas recovery systems. The gas from furnaces is burnt and wasted, which results in air pollution. To cover the furnaces, grading of powder materials is indispensable for improving the ventilation in furnaces. In Japan, sintering and pelletizing methods were developed. In China, the covering and gas recovery are performed for furnaces using expensive massive ores. In most cases, they are not performed. For three works at Jilin, Lioyang and Jinzhou surveyed in this project, recovered gas can be effectively utilized, which would provide energy saving and environment improving effects. They have enough site areas and workshops in the sites. Construction works can be conducted by China themselves. 6 figs., 32 tabs.

  15. Survey of technological advancement of coal exploitation in Asia and Pacific for fiscal 1997. Formulation of production plans for model coal mines in China; 1997 nendo Asia Taiheiyo sekitan kaihatsu kodoka chosa. Chugoku ni okeru model tanko no seisan keikaku no sakutei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In view of the prospective demand for coal in China and of the current state of transportation, a development plan is formulated for Tangkou Mining Area (of model mines) for the purpose of realizing efficient exploitation of coal. The infrastructures for coal transportation are complete in this area, and delivery of coal is easy from this area to the coal demanding regions. Although coal seams are quite deep in the ground, the important ones contain rich reserves. Exploitation is carried out under a vertical shaft scheme, in which pits extend horizontally at the level of 950m below the sea surface. As for production, an annual yield of 3-million ton is predicted thanks to two compositely mechanized coal faces. Coal is won by the monolayer side hole method in the case of seams not thicker than 4.0m, and by the caved stope method in the case not thinner than 4.0m. Employed for the mines are 1077 people. Operation days are 300, efficiency 15t/man/shift. The annual sale in total is expected to be worth 759-million 534.6-thousand yuan. To be required for the construction will be 1.2-billion yuan for mines and 0.2-billion yuan for coal dressing facilities, or 1.4-billion yuan in all, and the figures indicate that the plan is economically promising. 43 figs., 119 tabs.

  16. Effects of solvent and catalysts on the hydrogenolysis of alkylnaphthalenes; Alkylnaphthalene no suisoka bunkai ni okeru yobai to shokubai no koka

    Energy Technology Data Exchange (ETDEWEB)

    Futamura, S. [National Institute for Resources and Environment, Tsukuba (Japan)

    1996-10-28

    Catalytic effects of metal and carbon materials, which promote hydrogen transfer from hydrogen donor solvents, are investigated during hydrogenolysis of benzyl-1-methylnaphthalenes (BMN) selected as a hydrogen acceptor. For the isomer distribution of BMN after the reaction, almost the same molecular ratio before the reaction was obtained independent of the presence of catalysts. Selectivity of position during the addition of hydrogen atoms from tetralin was not found. For the reaction of BMN in tetralin, 1-methylnaphthalene and toluene were obtained as products, but the formation of benzylnaphthalene was not found. As for the nuclear hydride of BMN, the trace amount formation was confirmed by gas chromatography. For the hydrogen transfer from tetralin progressed catalytically, it was found that the nuclear of naphthalene can not be hydrogenated easily. This was considered to be due to the obstruction of hydrogen transfer from tetralin by the strong adsorption of BMN on the Ni surface. 1 ref., 1 fig., 2 tabs.

  17. Formation of spinel inclusions in molten stainless steel under Al deoxidation with slags; Slag kyozonka no Al datsusan katei ni okeru stainless yokochu spinel kaizaibutsu no seisei

    Energy Technology Data Exchange (ETDEWEB)

    Nishi, T.; Shinme, K. [Sumitomo Metal Industries, Ltd., Osaka (Japan)

    1998-12-01

    Morphology change of inclusions were experimentally investigated under Al deoxidation of molten stainless steel with CaO-SiO{sub 2}-Al{sub 2}O{sub 3}-MgO slags in order to clarify the morphology control factor of inclusions. 15kg of molten 18mass%Cr-8mass%Ni stainless steels were deoxidized by aluminum at 1873K, and the samples were taken at intervals to observe the inclusions by SEM and EDS. As the results, MgO contents of alumina type inclusions were gradually increased with time and the maximum contents were affected by a CaO/SiO{sub 2} ratio in slags. The formation of MgO-Al{sub 2}O{sub 3} spine type inclusions were also observed in case of high CaO/SiO{sub 2} ratio. The origin of Mg in inclusions was presumed to be deformation of MgO in slags. (author)

  18. Characterization of the various catalyst for solvent hydrogenation at 1t/d PSU; 1t/d PSU ni okeru kakushu yozai suisoka shokubai no seino hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Kakebayashi, H.; Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan); Aihara, Y.; Imada, K. [Nippon Steel Corp., Tokyo (Japan)

    1996-10-28

    Performance of various catalysts for hydrogenation of recycle solvent was evaluated for the operation of NEDOL process 1 t/d process supporting unit (PSU). Distillate between 220 and 538{degree}C derived from the liquefaction of Tanito Harum coal was used as recycle solvent. Deactivation behaviors of catalysts were compared using a prediction equation of catalyst life, by which aromatic carbon index (fa) after hydrogenation can be determined from the fa of recycle oil before hydrogenation, reaction temperature, and total hydrogenation time. Total hydrogenation time satisfying the {Delta}fa, 0.05 before and after hydrogenation were 8,000, 4,000, and 2,000 hours for NiMo-based catalysts C, A, and B, respectively. Catalyst C showed the longest life. Used catalysts were also characterized. The catalyst C showed larger mean pore size than those of the others, which resulted in the longer life due to the delay of pore blockage. From measurements by XPS and EPMA, relative atomic concentration of carbon increased remarkably after the use for all of catalysts, which was considered to be due to the adhesion of hydrocarbons. Increase of metal atoms, such as Fe and Cr, was also observed due to the contamination of entrainment residues. Deactivation of catalysts was caused by the adhesion of hydrocarbons, and metallic compounds, such as Fe and Cr. 3 refs., 1 fig., 5 tabs.

  19. Construction progress of Shimane Nuclear Power Station Unit No.3 supplied for the Chugoku Electric Power Co., Inc

    International Nuclear Information System (INIS)

    Hitachi-GE Nuclear Energy, Ltd. is now constructing Shimane nuclear power station unit No.3 supplied for The Chugoku Electric Power Co., Inc. Commercial operation is planned to start in December 2011. Hitachi's state-of-the-art construction technologies are applied and all construction milestones have been on schedule without any problems. (author)

  20. Effect of microstructure on statistical scatter of crack initiation and growth lives in NiCrMoV cast steel. NiCrMoV chuko ni okeru kiretsu no hasseiter dot denpa jumyo no baratsuki ni oyobosu zairyo bishi soshiki no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Ishii, A.; Ochi, Y.; Sasaki, S.; Nakamura, H. (The University of Electro-Communications, Tokyo (Japan))

    1991-05-15

    In order to clarify the cause of statistical scatter of crack initiation lives and growth lives in NiCrMoV cast steel for large-size turbine rotor shafts, the initial crack growth behavior and crack initiation sites were studied in detail. Rotating bending fatigue tests were carried out for four kinds of stress amplitudes including one just above a fatigue limit in air at room temperature, and fatigue process was divided into several ones according to a crack length range. By analyzing the number of cycles required for crack growth in each range, the crack length affecting strongly scatter of fatigue lives was examined. Since from scanning electron microscopic observation of crack initiation sites, most of the cracks were initiated from inclusions, the relation between the initiation lives and the size, shape and depth of inclusions was also examined. In addition, the crack length range sensitive to microstructure was considered on the basis of the correlation between a crack growth rate and stress intensity factor on log-log relation. 9 refs., 10 figs., 4 tabs.

  1. Effect of massive transformation on formation of acicular structure in austenitic stainless steel weld metal solidified as ferritic single phase. Report 5. Study on solidification and subsequent transformation of Cr-Ni stainless steel weld metals; Feraito tanso de gyokosuru osutenaito kei sutenresu ko yosetsu kinzoku ni okeru ashikyura jo soshiki no keisei ni oyobosu masshibu hentai no eikyo.5. Cr-Ni kei sutenresu ko yosetsu kinzoku no gyoko/hentai ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Inoue, H.; Koseki, T.; Okita, S.; Fuji, M. [Nippon Steel Corp., Tokyo (Japan)

    1997-05-05

    The authors clarified that massive transformation occurs at two phase region under To temperature and there is K-S relation between the massive formation phase and base phase using {gamma} stainless steel that solidifies at F mode and forms acicular structure at room temperature structure. There is a possibility of massive transformation in weld metals because the cooling rate below the high temperature To was high even for normal welding process. Thereupon, in this report, whether the massive transformation effects the formation of acicular structure or not was studied as for {gamma} stainless steel weld metal that solidifies at F mode and room temperature structure becomes acicular form of two {delta} and {gamma} phase. As a result, it was clarified that massive transformation occurs at two phase region with temperature below To, and the room temperature structure was acicular form structure irrespective to massive transformation in case of composition with small Cr/Ni ratio even in case of stainless steel that solidifies at F mode. 20 refs., 15 figs., 1 tab.

  2. Power distribution automating system of Chugoku Electric Power Company (function to link with high-voltage system control); Chugoku Denryoku (kabu) haiden jidoka system. Koatsu keito kanri system tono renkei kino

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-01-10

    Chugoku Electric Power and Fuji Electric have developed a function to save man-power in data maintenance work in power distribution systems, whose data keep changing due to everyday work, by means of linking a high-voltage system control system with a power distribution automating system. The features of this function may be summarized as follows: (1) the linkage is performed by using the standard protocol (TCP/IP); (2) high-voltage distribution facility data are linked in units of construction names in the distribution systems, making facility data maintenance of the systems possible without a need of inputting data in the power distribution automating system; (3) data are linked periodically on the number of customers in a switch section and on change in facility capacity, with renewal enabled; and (4) linked data and the data on the power distribution automating system side are compared, when consistency in switch and device attributes, network and section facility data is checked automatically. (NEDO)

  3. Alloying effects of Cr and Re on the hot-corrosion of nickel-based single crystal superalloys coated with a Na sub 2 SO sub 4 -NaCl salt. Na sub 2 SO sub 4 -NaCl kongoen tofu shiken ni okeru nickel ki tankessho chogokin no koon fushoku ni oyobosu Cr oyobi Re no koka

    Energy Technology Data Exchange (ETDEWEB)

    Matsuki, K (Toyohashi Univ. of Technology, Aichi (Japan). Graduate School); Kawakami, M.; Murata, Y.; Morinaga, M.; Yukawa, N. (Toyohashi Univ. of Technology, Aichi (Japan)); Takayanagi, T. (The Government Industrial Research Inst. Nagoya, Nagoya (Japan))

    1992-05-01

    The corrosion of nickel-based superalloys is represented by hot-corrosion due to Na {sub 2}SO{sub 4}contained in the combustion ashes of jet engines in aircraft. Therefore, in this study, the experiments are executed with the alloy based upon Ni-10Cr-12Al-1.2Ti-2.7Ta-2.0W-0.7Mo(TUT101) alloy with increased content of Cr as 13 mol% and 16 mol%, coated with a Na{sub 2}SO{sub 4}-45 mol%NaCl salt under 1173K, and the effects of Cr on the hot-corrosion are investigated. Further, the experiments are also carried out with the alloys based on Ni-9/10Cr-12Al-2Ti-1.1/1.2Ta-3.8W-0/1Re as well as the said TUT101 alloy with eight varying stages of Re content in the range of 0 to 0.5 mol%, coated with the same mixture salt as mentioned above to observe the effects of Re to the hot-corrosion. 15 refs., 8 figs., 2 tabs.

  4. Detection of vehicle crossing path at intersection; Mitoshi no yoi kosaten ni okeru deaigashira jiko ni tsuite (Ibarakiken ni okeru jiko tahatsu zone no tokucho)

    Energy Technology Data Exchange (ETDEWEB)

    Fujita, K.; Uchida, N.; Katayama, T. [Japan Automobile Research Institute Inc., Tsukuba (Japan)

    1997-10-01

    An investigation was excuted to understand the actual state of accidents happened at intersections where there were no constructive obstacles in field of view. First, the aspects of fatal accidents are described under the basis of the data published by the police of Ibaraki prefecture. Then it is shown that there are at least 336 intersections where the accidents happened in the last two years. It is also clarified that many dangerous zones were located in line along rivers. The authors stress that it is urgent to inform the existence of dangerous zones to prevent the accidents. 2 refs., 5 figs.

  5. Cause of and countermeasures to manual shutdown of No.1 plant in Shimane Nuclear Power Station, Chugoku Electric Power Co., Inc

    International Nuclear Information System (INIS)

    No.1 plant in Shimane Nuclear Power Station, Chugoku Electric Power Co., Inc. is a BWR plant with the rated output of 460 MWe. During its operation at the rated output on September 6, 1989, the alarm 'Large vibration in reactor recirculation pump motor (B)' occurred intermittently, consequently, the reactor was manually shut down at 1530 hours on the same day. As the result of investigation, it was found that an alien matter adhered to the action part of the vibration detector attached to the motor of the reactor recirculation pump (B), and the detecting sensitivity changed, consequently,the detector caused error action. Therefore, it was decided to remove the vibration detectors attached to the motors from both reactor recirculation pumps (A) and (B), and to install the vibration measuring instruments with higher reliability and excellent monitoring performance. (K.I.)

  6. Study on the time-domain electromagnetic responses; TDEM ho ni okeru denji oto ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Noguchi, K.; Endo, M. [Waseda University, Tokyo (Japan). School of Science and Engineering

    1997-05-27

    With an objective to perform three-dimensional analysis with high accuracy in using the electromagnetic exploration method, characteristics in electromagnetic response were analyzed, and conditions for acquiring necessary data were discussed. The discussion defined a parameter called `response anomaly` which uses response from media to standardize response only from substances with abnormal resistivity. The receivers were located uniformly on the same plane, and the response anomaly was derived from electromagnetic response from each of the three horizontal and vertical components at each receiving point, which was expressed as a contour map. The parameter for the abnormal body was consisted of location and resistivity contrast with media. Discussions using the contour map were given on the response when these factors for the parameter were varied. As a result, it was found that the response anomaly appears in the form that reflects the abnormal body, and the response anomaly of the horizontal component is superior in terms of being large. It was also referred that, as a requirement for the abnormal body which gives larger impact from the electromagnetic response, the abnormal body should have lower resistivity than that in the media, and resistivity contrast with the media should be greater. 2 refs., 7 figs., 1 tab.

  7. Detailed seismic intensity in Morioka area; Moriokashi ni okeru shosai shindo bunpu

    Energy Technology Data Exchange (ETDEWEB)

    Saito, T.; Yamamoto, H.; Settai, H. [Iwate University, Iwate (Japan). Faculty of Engineering; Yamada, T. [Obayashi Road Construction Co. Ltd., Tokyo (Japan)

    1996-10-01

    To reveal a seismic intensity distribution in individual areas, a large-scale detailed seismic intensity survey was conducted in Morioka City through questionnaire, as to the Hokkaido Toho-oki (HE) earthquake occurred on October 4, 1994 with a record of seismic intensity 4 at Morioka, and the Sanriku Haruka-oki (SH) earthquake occurred on December 28, 1994 with a record of seismic intensity 5 at Morioka. A relationship was also examined between the seismic intensity distribution and the properties of shallow basement in Morioka City. The range of seismic intensity was from 2.9 to 4.6 and the difference was 1.7 in the case of HE earthquake, and the range was from 3.1 to 5.0 and the difference was 1.9 in the case of SH earthquake. There were large differences in the seismic intensity at individual points. Morioka City has different geological structures in individual areas. There were differences in the S-wave velocity in the surface layer ranging from 150 to 600 m/sec, which were measured using a plate hammering seismic source at 76 areas in Morioka City. These properties of surface layers were in harmony with the seismic intensity distribution obtained from the questionnaire. For the observation of short frequency microtremors at about 490 points in the city, areas with large amplitudes, mean maximum amplitudes of vertical motion components more than 0.1 mkine were distributed in north-western region and a part of southern region. 4 refs., 9 figs., 1 tab.

  8. Magnetic prospecting in Kaibuki-yama ancient tomb; Kaibukiyama kofun ni okeru zenjiryoku sokutei

    Energy Technology Data Exchange (ETDEWEB)

    Nishitani, T. [Akita University, Akita (Japan). Mining College

    1996-10-01

    Kaibuki-yama ancient tomb located in Kumeda, Kishiwada City, Osaka has a square shape in the front and an orbicular shape in the rear, which was considered to be made in the 4th century. This ancient tomb has a total length about 135 m, a diameter of orbicular shape in the rear about 82 m, and a height about 9 m, which is a symbolical existence of the Kumeda ancient tombs. Stone chamber and stone casket made of Sanbagawa crystalline schist or rhyolitic-andesitic tuff are expected in this tomb. Magnetic prospecting in this study is accompanied with this survey. A differential type proton magnetometer was used for the measurements, which were conducted using meshes with 1 m edges. A pair of distinct positive and negative magnetic anomalies were observed in the center of orbicular shape in the rear. This coincides with a location of main body buried, which is archaeologically estimated. The magnetic anomaly might be caused by the article buried in the tomb, such as ironware, based on the measurement of magnetic intensity. From the calculated values of magnetic anomaly using a model, the buried article with magnetic anomaly was considered to have a size with length of 1 m, width of 0.1 m, and height of 0.2m. The negative magnetic anomaly could not be explained only by this. It is necessary to consider the other reasons. 8 refs., 8 figs.

  9. Characteristics of microtremors in Hanshin area; Hanshin chiiki ni okeru bido no kihon tokusei nitsuite

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, H.; Suzuki, K.; Yamanaka, H.; Seo, K. [Tokyo Institute of Technology, Tokyo (Japan)

    1996-10-01

    To increase general understandings of fundamental characteristics of microtremors in Hanshin area, microtremors have been observed at Sumiyoshi River-side, Rokko Island, and Nishinomiya. Relations were discussed among the stability of predominant period, successive fluctuation and meteorological conditions. For the analysis, cosine-type taper was conducted before and after 10% of the observed records, and Fourier spectrum was calculated by smoothing using Parzen window with a band width 0.3 Hz. Geometrical mean of two components was used as a horizontal component. At the observation points except Sumiyoshi River-side, predominance in the short period side was not distinct, and was not stable due to the successive fluctuation of predominant period. However, there was less successive fluctuation of spectrum ratio between different two points in the band with period more than 1 sec. Since there was a close correlation between the successive fluctuation in this band and the wind velocity or air pressure, the microtremors in this band was affected by a single vibration source. Ground characteristics could be illustrated by the averages of ratio against base points of moving observation. 14 refs.

  10. Autosolvent effect of bitumen in thermal cracking; Netsubunkai hanno ni okeru bitumen no jiko yobai koka

    Energy Technology Data Exchange (ETDEWEB)

    Mikuni, M.; Sato, M.; Hattori, H. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology; Nagaishi, H.; Sasaki, M.; Yoshida, T. [Hokkaido National Industrial Research Institute, Sapporo (Japan)

    1996-10-28

    Tar sand bitumen is petroleum-based ultra-heavy oil, and has a great amount of reserve like coal. However, there are still a lot of problems for its highly effective utilization. This paper discusses whether the light components in bitumen show independent behavior during the thermal cracking of heavy components, or not. Solvent effect and reaction mechanism during the thermal cracking are also derived from the change of their chemical structures. Athabasca tar sand bitumen was separated into light and heavy fractions by vacuum distillation based on D-1660 of ASTM. Mixtures of the both fractions at various ratios were used as samples. Negative effect of the light fraction on cracking of the heavy fraction was observed with dealkylation and paraffin formation Polymerization of the dealkylated light fraction to the heavy fraction was suggested due to lack of hydrogen in the thermal cracking under nitrogen atmosphere, which resulted in the formation of polymer. 3 refs., 6 figs.

  11. Volatiles production from the coking of coal; Sekitan no netsubunkai ni okeru kihatsubun seisei

    Energy Technology Data Exchange (ETDEWEB)

    Yamashita, Y.; Saito, H.; Inaba, A. [National Institute for Resources and Environment, Tsukuba (Japan)

    1996-10-28

    In order to simplify the coke manufacturing process, a coke production mechanism in coal pyrolysis was discussed. Australian bituminous coal which can produce good coke was used for the discussion. At a temperature raising rate of 50{degree}C per minute, coal weight loss increases monotonously. However, in the case of 3{degree}C, the weight loss reaches a peak at a maximum ultimate temperature of about 550{degree}C. The reaction mechanism varies with the temperature raising rates, and in the case of 50{degree}C per minute, volatiles other than CO2 and propane increased. Weight loss of coal at 3{degree}C per minute was caused mainly by methane production at 550{degree}C or lower. When the temperature is raised to 600{degree}C, tar and CO2 increased, and so did the weight loss. Anisotropy was discerned in almost of all coke particles at 450{degree}C, and the anisotropy became remarkable with increase in the maximum ultimate temperature. Coke and volatiles were produced continuously at a temperature raising rate of 50{degree}C per minute, and at 3{degree}C per minute, the production of the coke and volatiles progressed stepwise as the temperature has risen. 7 refs., 6 figs.

  12. Crack velocity in thermally tempered glass; Netsukyoka glass ni okeru crack no denpa sokudo

    Energy Technology Data Exchange (ETDEWEB)

    Aratani, S.; Yamauchi, Y. [Central Glass Co. Ltd., Tokyo (Japan); Takahashi, K. [Kyushu University, Fukuoka (Japan). Research Institute for Applied Mechanics

    1997-09-01

    The crack velocity in the thermally tempered glass prepared with an ordinary float glass composition was measured together with crack branch patterns using a Cranz- Schardin high-speed camera. The tempered 3.5mm-thick glass plates with three different levels of surface residual compressive stresses were used. The following useful results were obtained. The crack terminal velocity of the thermally tempered glass plate treated according to JIS R3206 (surface compressive stress: 172MPa) was estimated to be 1.500times10{sup 3}m/s. Those of the lower thermally tempered glass plates of 129MPa and 123MPa in surface compressive stress were 1.494 and 1.486times10{sup 3}m/s, respectively, showing a clear difference in compressive stress due to a degree of tempering. Under this experimental condition, the almost linear correlation was found between the crack velocity and surface compressive stress of glass plates. It was clarified that the crack velocity decreases with a decrease in surface compressive stress. 27 refs., 8 figs., 1 tab.

  13. Array TDEM survey at the Yufuin fault; Yufuin danso ni okeru array shiki TDEM tansa

    Energy Technology Data Exchange (ETDEWEB)

    Mogi, T. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Tanaka, Y.; Fukuda, Y. [Kyoto University, Kyoto (Japan). Faculty of Science; Jomori, N. [Chiba Electric Research Institute Co., Chiba (Japan)

    1996-10-01

    The array arrangement of receivers was studied to improve the resolution of LOTEM (long offset transient electromagnetics) survey. To eliminate the effect of underground structure from a source to a receiving point, continuous array arrangement from a source site is desirable. The survey at the Yufuin fault was carried out by arranging TEM receivers at intervals of 100m from the source. Since the synchronization between transmitting and receiving points by high-precision clock is essential, an amplifier for a flux gate magnetometer capable of measuring at four points at the same time was used. In the south plateau of the Yufuin basin, a relatively high resistivity stratum more than several tens ohm m exists at depth less than several hundreds meter, and a low resistivity stratum less than 10 ohm m exists under that. Those boundary depth increases toward the north up to 950m, and the depth subsequently decreases toward the north until the low resistivity stratum disappears. In addition, the uniform stratum of 1000m deep continues toward the north. Such precise resistivity structure around the fault was obtained by dense arrangement of measuring points. 4 refs., 7 figs.

  14. Appropriate technology in environmental sanitation; Kaihatsu tojokoku ni okeru kankyo eisei bunya no tekisei gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Kitawaki, H. [Toyo Univ., Gunma (Japan)

    1997-10-05

    For solving the problems of environmental sanitation in developing countries, assistance projects in respect of the supply of safe water and the maintenance of urine/waste water treating facility are developed by the aid organizations and civilian organizations of Japan. However, the funds, technology, capable persons, materials, etc. in developing countries are restricted in various ways, so there are a lot of cases that can not be approached by the methods in developed countries. In this paper, the appropriate technology in the environmental sanitation field in developing countries is described with practical cases. For example, there is a case that, regarding the wastewater treatment, a stabilizing pool is a safer treatment than the activated sludge process. Since the retention time in the stabilizing pool is longer than 10 days, parasitic worms in feces is settled and germs die out considerably. On the other hand, although the activated sludge process has a good removal rate of BOD, it is not an appropriate technology in developing countries because the removal rate of parasitic worms and germs are not good thus a disinfection is necessary, and additionally the electric power is rather consumed in operation. 2 refs., 4 figs., 1 tab.

  15. Advanced technology trend survey of micromachines in Europe; Oshu ni okeru micromachine sentan gijutsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    In this research survey, the development trend of micromachine technology in Europe was surveyed, development level of micromachine technology of European companies was grasped, and practical application fields of their target were investigated. Technology development level of private companies in Japan`s national projects and practical application fields of Japan`s target were arranged. Trends of micromachine technology development are compared between Japanese companies and European companies. Among micromachine technology development projects in Europe, ``8520 MUST`` is a part of the ESPRIT Project. About 40,000 companies among about 170,000 companies in whole Europe are relating to the MUST Project. The main fields include the manufacturing technology, process control of machines, technology of safety, sensor technology in environmental fields, and automotive technology. The marketing fields of application include the automobile, military technology, home automation, industrial process, medical technology, environmental technology, and games. The results can be compared with the direction of research and development in Japan. 22 figs., 8 tabs.

  16. Decentralized load frequency control on each power plant. Hatsudensho level ni okeru bunsangata fuka shuhasu seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, E.; Hasegawa, J. (HOkkaido Universtiy, Sapporo (Jpaan))

    1991-02-20

    Because of relatively decreasing hydraulic power plants, it becomes difficult to secure an electric power capacity needed for load frequency control of the electric power system. Accordingly, application is studied of the modern control theory based on a state equation instead of the classic control theory. To improve control characteristic by transmitting as little information as possible, decentralized control on each power plant level is studied and applied to a model. The following is a summarized conclusion: By detecting by an integral compensator and controlling variables which are equal to voltage phase angle deviations, frequency deviations or interchange power deviations can be controlled without information on interconnected-power-line tide deviations or interchange power deviations. Designing and practical operation of this system are easy because the control system is structured by the information including frequency deviations only from each power plant. Moreover, if some state variables are not available, the control system can be designed with a dynamic compensator. 6 refs., 4 figs., 2 tabs.

  17. Hydraulics and pneumatics education in Toyama University; Toyama Daigaku ni okeru yukuatsu kyoiku

    Energy Technology Data Exchange (ETDEWEB)

    Ossumi, T.; Takase, H. [Toyama University, Toyama (Japan). Faculty of Engineering

    2000-03-15

    Explained in this paper are part of problems in fluid power technology and their relation with the education and research that the writers are conducting, as well as the studies and student training which are dealt with in the laboratory of the department of mechanical intelligent system engineering and which are intended to enhance mechanical intelligence and students' enthusiasm. The first example is the embodiment of a digital control system using a computer and DSP, namely, a hydraulic pneumatic static-pressure bearing system with robustness contrived against disturbances by observers. Through such application examples to a hydraulic servo system and to a hydraulic pneumatic control valve, the education is given for the application of modern control theory to a fluid power system and for the method and significance of integration/intelligence technologies. The second example is an attempt to raise enthusiasm and interest to a fluid power system through the sense of amusement, which is a challenge to deal with a hydraulically driven quadruped walking machine. The machine is provided with 8 pieces in total of indirect electric/hydraulic servo driving systems and capable of walking with a child loaded on it. In learning robotics and a walk control technology, these attempts help students to have interest and understanding, facilitating education for hydraulics and pneumatics. (NEDO)

  18. Ship automation technology. Instrumentation and navigation; Senpaku ni okeru jidoka gijutsu no genjo. Keiso to kokai

    Energy Technology Data Exchange (ETDEWEB)

    Sato, T. [Mitsui Engineering and Shipbuilding Co. Ltd., Tokyo (Japan)

    1996-02-01

    This paper summarizes facilities in automated vessels and automation technologies. The purpose of automation is to save energies, achieve navigation safety and high-efficiency navigation, and preserve the environment. Control theories required for automation include the PID control as a feedback control, and the feedforward control as a modern control theory. Actual installation of the automated systems may be enumerated as follows: remotely controlled wing operating and steering devices as power saving devices in ore transport vessels, hutch cover and ore removing device, totally remotely controlled ship mooring machine and one-man tug line device, and a sludge solidification treatment system; a merchant ship was installed with a controlling and monitoring system of marine devices consisting of a controlling and monitoring network for two systems, and a safety system network for two systems. The future marine vessel automating technology would advance in the areas of increasing speed and capacity and reducing size of computers and LANs as well as standardizing hardwares and softwares. As the automation trend in the futuristic vessels, proposals have been given on automating the centralized control and monitoring at an adequate level, improving the safety devices, considering more on energy conservation and environments, and improving the reliability. 5 refs., 4 figs., 6 tabs.

  19. Trend of welding robot for bridge construction; Kyoryo ni okeru genba yosetsu no jidoka robot ka

    Energy Technology Data Exchange (ETDEWEB)

    Yasuda, O. [Takada Kiko Co. Ltd., Osaka (Japan)

    1997-12-01

    This paper explains general bridge construction methods and describes future problems therein on automation and robotization of site welding in bridge construction. Site jointing in bridge construction has used high-strength bolt jointing as the mainstream until recently, but adoption of site welding is now increasing. Steel bed plates, box girders, I-shaped girders, and bridge piers have different characteristic requirements in welding volume and plate thickness, to which carbon dioxide arc-welding and submerged-arc welding are used depending on welding postures. Anti-seismic reinforcement construction on RC bridges has started with the Great Hanshin Earthquake as a turning point (steel plates are wound round columns, welded by CO2 arc-welding using the backing strip system, and resin and/or mortar are filled into clearance between RC and the steel plates). This construction requires vertical welding work with welding length as long as 10 m or longer, making the automation and robotization great advantages. For all cases, robotization in site constructions has just begun, whereas a number of problems desired of solution on robots exist, such as high-efficiency welding, and weldable postures the robots can take. 1 ref., 13 figs.

  20. Welding mechanization in shipyard CIM; Zosen ni okeru yosetsu no jidoka robot ka CIM ka

    Energy Technology Data Exchange (ETDEWEB)

    Miyazaki, T. [Hitachi Zosen Corp., Osaka (Japan)

    1997-12-01

    This paper explains development and examples of application of automated welding devices from a viewpoint of an element technology constituting computer integrated manufacturing (CIM), based on the history of modernization of shipyards that has been achieved to date. In the first step of promoting the modernization, elevating cutting accuracy in the uppermost stream process was thought a starting point of rationalization. What have been achieved therefrom are adoption of the most advanced NC plasma cutting machine, and improvement in the computer aided system for the cutting machines. In addition, a twenty-electrode line welder has been developed, which does not create angle deformation in welding longerons, and can be operated even by unskilled workers. The welder has successfully realized a construction method in which robots can be applied more easily. Further developments have been made on a robot to weld cells, advanced CAD/CAM operation techniques which are linked with data from design, an automatic one-side welding device which can achieve a speed 2.5 times greater than by conventional devices, and an automation device for three-dimensionally bent blocks, whose automation has been regarded difficult. 11 figs., 1 tab.

  1. Automatic control technique for construction of work; Kensetsu koji seko ni okeru jidoka gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, T. [Ministry of Agriculture Forestry and Fisheries, Tokyo (Japan)

    1996-03-01

    In this article, the history of development of construction technology in Japan after the Second World War is outlined, in addition, automation of work and supervision in the latest construction works is explained relatively in detail, and the trend of automated and manpower saving works in the future is shown. Regarding the development of construction technology after the war in Japan, it started with the introduction of new construction methods, etc. of the U.S.A. and the Netherland for business of restoration immediately after the war and also the mechanized technology such as bulldozers was studied. After that, technology concerning reclamation, construction of dams and irrigation channels and construction of tunnels and bridges progressed. Regarding the latest construction works, explanations are given on the two fields, namely automation and manpower saving of construction works and automation and manpower saving of construction supervision. Concerning the former field, automation of works laying dam concrete, automation of treatment of joint between laid dam concrete, mechanization of removal work of the core surface water, etc. are described and regarding the latter, supervision of compacting banking, photo supervision with digital cameras, etc. are referred to. The article also hints the trend in the future. 4 refs., 5 figs..

  2. Mechanized and robotized welding in shipbuilding; Zosen ni okeru yosetsu no jidoka robot ka

    Energy Technology Data Exchange (ETDEWEB)

    Kanda, Y. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1997-12-01

    Large-scale ships such as VLCC are built at the Kure No.1 Works of IHI (Ishikawajima-Harima Heavy Industry). This paper introduces current status of mechanized and robotized welding at the works. For the sub-assembly with short weld length and horizontal fillet, simplified automatic welders are used in which mag-welding method using CO2 is adopted. The frequent wound welding of member ends can be automatically conducted using welders developed by IHI. In the large-scale assembly processes, remarkable rationalization and highly accurate assembly of flat plate welding have been promoted. Tankers, container ships, and bulk carriers can be treated at the same time. Teaching times of welding robots can be greatly reduced by a technique called parametric treatment. In the future, it is essential to enhance the accuracy of members by introducing the laser cutting during machining processes. Completely self-type mechanization is required as well as large-output laser welding and sensor technology. 3 refs., 12 figs., 2 tabs.

  3. Present status of geothermal power development in Kyushu; Kyushu ni okeru chinetsu hatsuden no genjo

    Energy Technology Data Exchange (ETDEWEB)

    Akiyoshi, M. [Kyushu Electric Power Co. Inc., Fukuoka (Japan)

    1997-10-20

    The present situation was introduced of the geothermal power generation in Kyushu. In Kyushu, where there are lots of volcanos and abundant geothermal resources, the geothermal exploration has been made since long ago. Three non-utility use units at three geothermal power generation points and six commercial use units at five points are now in operation in Kyushu. The total output is approximately 210 MW, about 40% of the domestic geothermal power generation. At Otake and Hacchobaru geothermal power plants, the Kyushu Electric Power Company made the geothermal resource exploration through the installation/operation of power generation facilities. At the Otake power plant, a geothermal water type single flashing system was adopted first in the country because of its steam mixed with geothermal water. At the Hacchobaru power plant, adopted were a two-phase flow transportation system and a double flashing system in which the geothermal water separated from primary steam by separator is more reduced in pressure to take out secondary steam. Yamakawa, Ogiri and Takigami power plants are all for the joint exploration. Geothermal developers drill steam wells and generate steam, and the Kyushu Electric Power Company buys the steam and uses it for power generation. 5 figs., 1 tab.

  4. Refraction experiment in the Kobe-Hanshin area; Kobe Hanshin kan ni okeru kussetsuho tansa

    Energy Technology Data Exchange (ETDEWEB)

    Koketsu, K. [The University of Tokyo, Tokyo (Japan). Earthquake Research Institute

    1996-05-01

    The refraction experiments were conducted to investigate the underground structures reaching the basement by analyzing the results of the artificial earthquakes the explosion earthquake research group produced in City of Kobe and the Hanshin District on December 12 to 15, 1995. Considering that noise level can exceed 1 mkine in an urban area even in the mid-night, the courses of traverse were drawn focusing on Points S2 through S4 and U1. The earthquake waves from Points S2 through S4 are generally low in amplitude. However, the major components of the signals have a dominant frequency exceeding 10Hz, which makes them distinguishable from urban noise having a lower frequency, contrary to the previous indication that such a low-amplitude wave might not be distinguishable. On the other hand, the signals from the explosion at Point 4 in Awaji Island cannot be distinguished in the urban area, even on the nearby course of traverse D. At present, the analytical group is organized to read various phases running and analyze the P-velocity structures. 2 refs., 10 figs., 1 tab.

  5. Aesthetic design of bridges; Kyoryo ni okeru keikan sekkei no rekishi

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, H. [Kyushu Institute of Technology, Kitakyushu (Japan)

    1995-01-01

    The present paper outlines the bridge design in harmony with both ambient and natural environments. The condition which the bridge must clear has its two phases, i.e., `rational phase` focused on the practical utility to be managed by the engineering and `sensible phase` for the aesthetic achievement. The profile and scenery of bridge are based on the perfect teleology to engineer and process them by taking the influence into consideration on the mental phase. The beauty of bridge belongs to a category of technical beauty converting the technical product into an aesthetic object. The technical beauty is composed of `formal beauty` (The composition of all different members forms the beauty of harmony.), `functional beauty` (All different members under tension generate the dynamic beauty.) and `harmony with the environment`. For the harmony with the environment, what is taken into consideration is the steel, concrete and other material feeling, type of bridge adaptable to the environment, and color good for the environment. The following three methods are applied to the combination of bridge and environment: elimination method to vaguely immerse the bridge in the environment. Accentuation method to select the bridge as a main element of scenery. Harmonization method to harmonize the bridge with the environment. 21 refs., 14 figs.

  6. Environmental action program of the electric utilities industry; Denki jigyo ni okeru kankyo kodo keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-30

    The electric utilities industry has established the environmental action program on the premise of stably supply of power. The measures for reduction of CO2 emissions include promotion of best power source mixes, centered by nuclear power generation which emits essentially no CO2; improvement of energy utilization efficiency by enhancing thermal efficiency at thermal power stations by adopting combined cycles and other advanced systems, and by reducing power transmission/delivery losses; introduction and diffusion of new energy sources, such as solar ray and wind power plants; development and diffusion of energy-saving systems, such as heat-storing heat pumps; and promotion of technical development for recovery, treatment and fixation of CO2. The measures for expanded utilization of coal ashes include expanded utilization of ashes as the starting material for cement and concrete; establishment of the specifications and standards of fly ashes, including revision of the current JIS specifications; and promotion of researches on and technical development of civil engineering and building areas in which ashes can be utilized. The program also stresses importance on voluntary and positive development of environment management and monitoring systems. 5 figs.

  7. Latest research trends at Civil Works Research Institute. Doboku kenkyusho ni okeru saikin no kenkyu doko

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, T. (Public Works Research Institute, Tokyo (Japan))

    1993-08-25

    This paper introduces a summary of the new organizations at the Public Works Research Institute and main research subjects on latest construction machineries and mechanized constructions. In the new organizational system, an environment department was inaugurated to handle unifiedly and integratedly the research subjects for efficient research and development of environmental problems, and a material execution department to promote developing technologies to design and execute utilization of new materials and construction of high-quality social infrastructures safely and efficiently. New execution techniques in the construction business include automation techniques to utilize advanced techniques, deal with works under dangerous environments, and realize high-level execution and quality control. Techniques to prefabricate reinforced concrete structures have been developed to reduce work loads at sites. Studies on execution improving methods in mechanized constructions discuss application of systematic and analytically scientific industrial engineering methods (IE) to civil engineering works. Other efforts include development of a standardized execution information system operated unifiedly and efficiently among a large number of users using IC cards, and development of low-noise hydraulic breakers. 7 figs., 1 tab.

  8. Trend of STEP development activities at ISO; ISO ni okeru STEP no doko

    Energy Technology Data Exchange (ETDEWEB)

    Yamashita, J

    1998-09-05

    Technical committee 1884: Industrial Automation and Integration and Sub Committee 4: Industrial Data are huge organizations established in 1984 and include development theory and practical application. In TC 184 and SC 4, about 450 experts from 28 countries are participating and integration of technical information centering to product information is carried out by standardization and establish data base or information environment for sharing purpose. STEP (Standard for the exchange of product model data) is common name of ISO 10303 and is handled by TC 184 SC 4 in ISO organization. Standards under formulation such as WG 3: Product Models/T12 AEC: Building and Civil engineering and Building and Construction are the fields where Japan must participate and cooperate. In this report, organization of ISO developing ISO 10303 (STEP), the constitution of STEP, mechanism and step till the formulation of standard are discussed, and situation of building related Application Protocol (AP) development is cited. 5 refs., 5 figs.

  9. Application of liquid atomization to the pharmaceutical process. Iyaku ni okeru biryuka no oyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Takei, N. (Freund Industrial Co. Ltd., Saitama (Japan))

    1991-04-20

    A coating system is introduced as a liquid atomization technique for oral administration drug applied to the pharmaceutical process. Controlled release of drug dissolution in the human body is important. How to dissolve the drug by coating granules is described here. For example, the core of a drug granule is made up by spherical granulated sucrose, the intermediate layer as a main element by theophylline which is an asthma medicine, the outer layer by an ethylcellulose film. Theophylline takes 30 minutes to dissolve and the ethylcellulose-coated granule does more than 16 hours. A fluidized tumbled bed type coating apparatus is developed to prevent unevenness, adhesion and aggregation. Even in the same chemical species, the dissolution speed differs in a crystal type, crystalline or amorphous and anhydrous or hydrate. Acceleration of the drug dissolution is studied. A suspension which is an ethanol solution of hydroxy propy/cellulose with supersaturated antiflammatory drug, atomized by a jetcoating system, is coated on the surface of potato starch powder. The drug as a main element shows only a 10% dissolution rate in 8 hours. On the other hand, the drug coated show a 100% dissolution rate in 2 hours. This is because the coating crystallizes the drug itself in the film and promotes its dissolution. 6 refs., 8 figs.

  10. Human physiology and psychology in space flight; Uchu hiko ni okeru ningen no seiri to shinri

    Energy Technology Data Exchange (ETDEWEB)

    Murai, T. [National Space Development Agency of Japan, Tokyo (Japan)

    1999-10-05

    Human beings' adaptation to space and the effects on them of a prolonged stay in space are discussed. Some effects may be detrimental to crewmen even when they are medically judged as 'normal' and 'adaptable.' Bone deliming, muscular atrophy, and hypodynamia may be physiologically 'normal' and 'adaptable' in the zero-gravity environment where no strength is required to hold a position or attitude, and they will not cause any serious problems if crewmen are to stay in the zero-gravity environment permanently. Astronauts work on conditions that they return to the earth, however, and they have to stand on their own legs when back on the ground. Such being the case, they in the space vehicle are forced to make efforts at having their bone density and muscular strength sustained. It is inevitable for a space station to be a closed, isolated system, and the crewmen have to live in multinational, multicultural, and multilingual circumstances in case the flight is an international project. They will be exposed to great social and psychological stresses, and their adaptability to such stresses presents an important task. (NEDO)

  11. Review of geothermal development in Kyushu, Japan. Kyushu ni okeru chinetsu hatsuden no kaihatsu doko

    Energy Technology Data Exchange (ETDEWEB)

    Baba, Y. (The Kyushu Electric Power Co. Inc., Fukuoka (Japan))

    1992-07-30

    The geothermal development in Kyushu was reviewed. Now, 8 units in the five geothermal power plants are running and their availability factors are high like 90% and more. The 1st unit of Hatchobaru power station was the first one in the world as the double flash type, starting its commercial operation in 1977 and the output arrived at 55,000kW in 1980. The economy was pursued for the 2nd unit in addition to the same design idea as the 1st unit, which was commissioned in 1990 at the output of 55,000kW. The first geothermal power plant in Japan was constructed at Otake Power Station and arrived at 12,500kW in 1979. Suginoi power plant of 3,000kW output, Kirishima-Kokusai power plant of 450kw and Takenoyu power plant of 105kW which have been used for personal use, were also explained. Plans to construct power plants are prepared for new developing areas such as Yamakawa, Ogiri and Takigami, and in these cases, the system in which geothermal developers supply steam for power generation to the electric utility. The Japanese Government advances the survey to promote geothermal energy and the comprehensive survey for resources in the whole Japan. The total capacity of approved geothermal power stations in Japan is 270,000kW which is less than 1% of the total power generating capacity in Japan. The target in 2000 is 1 million kW, but there are many problems like developing risk, environmental protection and opposition of local people. 5 refs., 3 figs., 3 tabs.

  12. Development of a platoon driving AHS; AHS jikkensha ni okeru gunsoko seigyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Seto, Y.; Inoue, H. [Nissan Motor Co. Ltd., Tokyo (Japan)

    1997-10-01

    Nissan and the Public Work Research Institute of the Ministry of Construction are developing an Automated Highway System. We are investigating a longitudinal control system in AHS. In this paper, a vehicle control method using two actuators an engine and a brake, is described. Experimental and simulated results are shown. A Platoon driving control method using road-to-vehicle and vehicle-to-vehicle communication is described. And the influence of the communication on the control performance is shown by experiments and simulation. The effects of the communication device and control device mentioned above are verified by experimental results in an AHS field test conducted in September 1996 on a dosed highway. 5 refs., 8 figs.

  13. Annual energy review-1996; 1996 nen ni okeru juyona energy kankei jiko

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-07-20

    This paper reviews the important items concerned with energy in 1996. Primary energy supply sums to 529times10{sup 13}kcal increasing by 2.4% over last year. The growth rates of demand over last year are 2.5% in industry use, 3.7% in transport use, 3.7% in home use, and 1.3% in business use. On R & D trend of use technologies of energy resources, the following are described: (1) Petroleum: resource exploitation, transport, stock, refining, and petrochemistry, (2) Coal: resource exploitation, coal structure and property, processing, transport, liquefaction, gasification, carbonization, tar industry, carbon industry, and coal ash utilization, (3) Natural gas: resource exploitation, transport, storage, and conversion technology, (4) Natural energy: hydraulic, solar, geothermal, wind power, oceanic and biomass energies, and (5) Others: waste resources, hydrogen and alcohol. On R & D trend of energy conversion technology, combustion theory, boiler, engine, thermal energy system, and high-efficiency power generation technology are described. Environmental problems and their protective technologies are also described

  14. Dissipative structure of mechanically stimulated reaction; Kikaiteki reiki hanno ni okeru san`itsu kozo

    Energy Technology Data Exchange (ETDEWEB)

    Hida, M. [Okayama Univ., Okayama (Japan). Faculty of Engineering

    1994-12-20

    Recently various studies have been conducted concerning the state changes of materials obtained through mechanical alloying (MA) or mechano-chemical (MC) processing. What is noticeable is the quasi-steady state of almost all the materials obtained through various processes including MA and MC, and that the super cooling, supersaturating and high residue distortion realized under unbalanced conditions have not been clarified. In other words, the tracing capability to the external binding conditions is low. In this report, the appearance of the high temperature phase and high pressure phase obtained through MA or MC processing, the forming of amorphous, the mesomerism of the amorphous materials, the interesting phenomena generated by combination between the mechanical disturbance and chemical reactions were discussed with concrete examples, and a steady dissipative organization theory was approached from the viewpoint of dissipative structure development which is equal to the forming process of the quasi-steady phase. 34 refs., 2 figs.

  15. Outlook on shafting and propeller in future; Jikukei ni okeru kongo no tenbo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    This paper describes the technology trend of propulsion systems for ships, i.e., shafting and propeller. Contra-rotating propeller has been put into practice for energy saving, and new type stern tube sealing (non-leakage type) for marine pollution protection. Water jet propulsion machinery has been developed for high speed ships. Integrated control system for take-off and landing piers has been also developed. CAD and CAM were introduced for design methods. For the future trend of shafting and propeller, various considerations for needs, such as high speed of ships, reduction of noise discharge under water, and comfortableness, are to be problems. Gas turbines and water jet propulsion machineries are to be increasingly employed as main engines for high speed. Heavy-duty resistant vibration isolation rubbers and high torque resistant elastic couplings are desired to be developed as vibration isolation supports of main engines from the viewpoint of comfortableness. It is important for high reliability to accumulate the analyses of causes of accidents. It will be significant to exert effort for improvement of each part. This paper also describes propellers, stern tube bearings, and water jet propulsion machineries, respectively. It is forecasted that demand of price and reliability will increase furthermore.

  16. Recent tendency of technology on marine propeller; Saikin ni okeru propeller gijutsu no doko

    Energy Technology Data Exchange (ETDEWEB)

    Yoshioka, M

    1998-09-01

    This paper reviews the recent development of marine propellers and their computerized planning and manufacturing systems. A recent propeller planning system is explained first showing a figure. Propeller theories are then described. Low speed large propellers, high efficiency propellers with reduced are blades, and other types of energy saving propeller devices and appendages, such as contra-rotating propellers, propeller boss cap fins, contracted loaded tip propellers, tandem propellers, and etc. are described under the heading of energy saving propellers. The paper reports also the present state of cavitation, vibromotive force, singing, material and strength, and fitting methods of propellers. The manufacturing technology of propellers is dealt with dividing into the following headings, viz. Forging, NC blade surface machining, Grinding and polishing, and inspection. 17 refs., 14 figs.

  17. Treatment of opinions, etc. in the public hearing on the alteration of reactor installation (addition of Unit 2) in the Shimane Nuclear Power Station of The Chugoku Electric Power Company, Inc

    International Nuclear Information System (INIS)

    The Nuclear Safety Commission has acknowledged the governmental policy, and further decided on the treatment of the opinions expressed by the local people in the public hearing held in May, 1983, in Shimane Prefecture on the addition of Unit 2 to the Shimane Nuclear Power Station, Chugoku Electric Power Co., Inc. The NSC has directed the Committee on Examination of Reactor Safety to take into consideration the opinions in its later examination. The opinions expressed by the local people in the form of question are given as follows: siting conditions (earthquake, ground, weather, etc.), the safety design for reactor installation (general aspect, aseismatic design, core design, ECCS, the teaching of TMI accident, etc.), radioactive wastes, radiation exposure, site evaluation. (Mori, K.)

  18. On noise, traffic and factory vibrations in Akita city; Akitashi ni okeru soon oyobi kotsu kojo shindo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Nogoshi, M.; Kikuchi, T.; Morino, T.; Sannohe, M. [Akita University, Akita (Japan). College of Education

    1996-05-01

    Noise and vibration were measured in Akita City. In 1994, noise and traffic-caused vibration were measured along the trunk lines and other roads across the entire Akita City area. In 1995, the effort centered on the Ibarashima manufacturing quarters, the important source of noise and vibration in Akita city. The general-purpose noise meter LA-220S was used to measure noise and the vibration level meter VR-5100 was used to measure vibration. The results of noise measurement carried out at 122 points in Akita City indicated that the noise level was high along Route 7, Route 13, and the southern line belonging to the newly built national highway, marking the highest of approximately 74dB. As compared with the measurement made in 1968, the value was higher by 3-13dB. A roughly similar trend was seen in vibration. The noise level measurement of 1995 accomplished at 100 points in the vicinity of Ibarashima district indicated that the factories were responsible for high levels of noise and vibration. It was found that the levels lowered in proportion to the increase in the distance from the factories. 11 figs., 1 tab.

  19. On possibility of SSR in longitudinal power systems; Chokyori kushigata keito ni okeru SSR no kanosei ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Kakimoto, N.; Takuma, M. [Kyoto University, Kyoto (Japan); Sugihara, H. [Chugoku Electric Power Co. Inc., Hiroshima (Japan)

    1998-04-10

    In this paper, theoretical consideration is made on possibility of subsynchronous resonance (SSR) in longitudinal power systems. Shunt capacitors are used for reactive power compensation in our country, but series capacitors are not used in general. Possibility of SSR is therefore small. However, if power transmission increases, and accordingly, if shunt compensation increases in amount, there is no guarantee that SSR never occur. First, we investigate network impedance viewed from a generator. Its resonant frequencies get lower with increase in transmission power. One of them gets subsynchronous if the power exceeds a value. In this area, there is some possibility of SSR, which is confirmed with the damping property of the generator. The admittance matrix of the load buses are singular at the resonant frequencies. The number of them is equal to the dimension of the matrix. The frequencies are common to all generators but not limited to one particular generator. One of them gets equal to 60 Hz as we increase transmission power. We regard this power as a limit for SSR. However, steady state stability limit is lower than this limit, and steady operation is not possible at the limit. Therefore, it is impossible to enter the area of SSR. Thus we obtain a conclusion that SSR does not occur in shunt compensated systems. However, this property is easily lost if some series compensation is introduced. 13 refs., 7 figs., 2 tabs.

  20. Study on the optimal control of the ground thermal storage system in the greenhouse. Part 4; Onshitsu ni okeru taiyo energy dochu chikunetsu system ni okeru saiteki seigyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, M. [Sanko Air Conditioning Co. Ltd., Osaka (Japan); Nakahara, N. [Kanagawa University, Yokohama (Japan)

    1996-10-27

    Three types of weight in both energy saving and optimum room temperature environment were changed to obtain the optimal control solution of the ground thermal storage system in a greenhouse. The relation diagram between the optimal solution of a performance function, and the state constraints and control function constraints was created in consideration of the energy term in a control function value area and the room temperature environment. As a result, the whole image of the performance function could be grasped in consideration of the energy term with inequality constraints and the room temperature environmental term in this study. The rate of a weighting factor in the performance function significantly influences the optimal solution. The influence on the optimal solution also changes when the optimal room temperature schedule differs. The influence that three types of rising algorithm exert on the convergence and converging speed was investigated. Superiority or inferiority occurs according to the space properties of a performance function. A zigzag method is most disadvantageous. The constraints can be converged to the optimal solution using an SUMT outer point method irrespective of the initial value. 6 refs., 6 figs., 4 tabs.

  1. Anodic dissolution mwchanisms of copper in neutral carbonate-chloride solution. Tansan en oyobi enkabutsu yoeki chu ni okeru do no anodo yokai. Chusei yoeki chu ni okeru yokai kiko

    Energy Technology Data Exchange (ETDEWEB)

    Nishikata, Atsushi; Tsuru, Toru; Itagaki, Masayuki; Haruyama, Shiro; Fujii, Eiichiro (Tokyo Inst. of Technology, Faculty of Engineering, Tokyo (Japan) Tokyo Inst. of Technology, Tokyo (Japan) Tokyo National College of Technology, Tokyo (Japan) Toshiba Corp., Kawasaki (Japan))

    1990-01-15

    In this study, anodic polarization curves of copper in neutral solutions containing CO {sup 2 {minus}} {sub 3} and Cl {sup {minus}} ions were measured by the stationary solution and channel flow electrode method, the anodic dissolution mechanism of copper was studied and the effects of concentration of carbonate and chloride were investigated. As a result, the following was found: (1) Concerning the anodic polarization curves of copper, the oxidation region I toward univalent and the oxidation region II toward divalent appeared continuously like in the alkaline solution and a clear Tarfel relationship was obtained respectively. It was revealed that in both the oxidation region toward univalent and the oxidation region toward divalent, the eletric current relied only on the Cl sup - concentration and did not rely on PH and CO {sup 2 {minus}} {sub 3} concentrations. (2) Based on PH, CO {sup 2 {minus}} {sub 3} and Cl {sup {minus}} concentration dependability and the result of elused ionic species obtained by the channel flow electrode method, the reaction mechanism in the respective regions were clarified. 5 refs, 4 figs, 1 tab.

  2. 3D seismic survey in Honjo, Akita. Problems and struggles in acquisition and processing; Akitaken Honjo koku ni okeru sanjigen jishin tansa. Genba sagyo to data shori ni okeru mondaiten

    Energy Technology Data Exchange (ETDEWEB)

    Imahori, S.; Kotera, Y.; Nakanishi, T. [Japan Energy Development Co. Ltd., Tokyo (Japan)

    1997-05-27

    Honjo mining area where investigations are conducted is hilly and has a complicated terrain with gas pipes buried in the ground just under the access road disabling the proper positioning of shock-generating large excavators or vibrators. Auger`s shallow hole shooting method is used in this survey to execute blastings at 639 points. In this method using charge depths of 4m, different from the conventional method using deeper charge depths (20-25m), surface waves prevail in the shot records giving rise to a new problem of removing them in the stage of data processing. The 2D filter that is a powerful tool in 2D data processing is not available in a 3D-survey where the tracing intervals are irregular in the shot records. In the effort of this time, a window length as a parameter in the direction of time is specified, and the F-X dip filtering method is employed in which any event that linearly continues beyond a certain number of traces in the said window is eliminated as a linear noise. It is recommended that the weighting function be changed in the direction of space since surface wave velocities are different at different locations. 1 fig., 1 tab.

  3. Study of evaluation for grouting effect in a borehole; Yakueki chunyu koka hyoka gijutsu ni okeru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, H.; Matsuo, T. [Fukuoka Municipal Transportation Bureau, Fukuoka (Japan); Yamauchi, Y.; Imanishi, H. [Osaka Soil Test, Osaka (Japan)

    1996-10-01

    For the foundation improvement works by grouting in a borehole, evaluation of grouting effect is one of the most important management items. The grouting design and works are sometimes reconsidered depending on the evaluation of grouting effect during the test injection. The purpose of the evaluation of grouting effect is to grasp the range of improvement and consolidation after the injection, and to judge and estimate the strength and permeability of the consolidation part. This paper describes the judgment method of the strength using PS logging results and borehole televiewer (BHTV) logging results. The reflection intensity (Ir) by the BHTV logging increased after the grouting, which showed a same tendency as that using S-wave and P-wave velocities (Vs and Vp) before and after the grouting. This was considered to demonstrate the grouting effect. A relation was obtained between the Vs, Vp and Ir before and after the grouting, which was expressed by following equation. Ir=0.143{times}Vs-70=0.093{times}Vp-110. The relation with the dynamic elastic coefficient (Ed) was also obtained as follow; Ir=0.0013{times}Ed. 9 figs.

  4. Seismic reflection survey in Omama fan area, Gunma prefecture; Gunma Omama senjochi ni okeru hanshaho jishin tansa

    Energy Technology Data Exchange (ETDEWEB)

    Yamaguchi, K.; Kano, N.; Yokokura, T.; Kiguchi, T.; Yokota, T.; Matsushima, J. [Geological Survey of Japan, Tsukuba (Japan)

    1996-10-01

    Seismic reflection survey was performed for the Medial Tectonic Line, an important geological tectonic line in the Kanto plains, at Kushibiki district, Saitama prefecture in the north-western part of the Kanto plains. It was estimated that movements of the basement were different in the individual sides of the active fault. In this study, the seismic reflection survey was performed at the Omama fan area, Gunma prefecture, which is located at the north-eastern extension of the Kushibiki plateau, to grasp the structure of basement to the depth of about 1.0 s of return travel time, and the upper sediments. Two traverse lines passing Ota city, Kiryu city, and Nitta town were used. Southern part of the traverse line-1 was in the bottom land in the middle of Tone river, and northern part was in the Omama fan area. The ground surface along the traverse line was flat. Hachioji heights are the heights elongating in the NW-SE direction and having relative height of 100 to 200 m against the surrounding plain. Another traverse line-2 was set on the steep slope having relative height more than 100 m. The Brute stack time section of each traverse line was characterized by the gradient reflection surface AA of the traverse line-1. It was suggested that the AA or intermittent parts of reflection surfaces deeper than AA may relate to the tectonic lines in the more ancient geological ages. 2 figs., 1 tab.

  5. Fault analysis in the very shallow seismic reflection method; Gokusenso jishin hanshaho ni okeru danso kaiseki. 1

    Energy Technology Data Exchange (ETDEWEB)

    Nagumo, S.; Muraoka, S.; Kaida, Y.; Takahashi, T. [OYO Corp., Tokyo (Japan)

    1996-10-01

    To effectively use the very shallow seismic reflection for active fault survey, a method has been investigated by which fault structures can be appropriately reconstructed from the fault information detected in the original records. The first step of reconstructing the fault system from the travel time reflection curve was to grasp an outline of fault structure from the patterns of travel time curve observed in the original record. For the very shallow seismic reflection method, especially, the low velocity layers in a shallow part succeeding from the ground surface made the issue complicated. Then, the travel time reflection curves were calculated in the case of existing several horizontal reflection surfaces in the surface layer. The constant values, mean velocities to the depth at individual reflection surfaces were used for the approximation of velocities. The outline of fault structure was grasped from the observation of original record. Then, the structure was reconstructed from the travel time curves. When the mean velocity in the medium was known, reconstruction of the feature of reflection surfaces from the travel time curves could be determined by simple mapping. When the mean velocity was unknown, it was calculated using the reciprocal travel time from the common reflection surface for individual reflection surfaces. 7 figs.

  6. Polymer-based matrix composites in general industries. Ippan sangyo bun'ya ni okeru kobunshiki fukugo zairyo

    Energy Technology Data Exchange (ETDEWEB)

    Kenmochi, K. (National Institute of Materials and Chemical Research, Tsukuba (Japan))

    1994-02-15

    This paper summarizes the course of development of polymer-based matrix composites (PMC) begun in the 1950's, their future problems, and prospects. Because of PMC being a petroleum product, the changing period before and after the first and second oil crises (1974-1983) has seen even a negative growth from the declined product price out of increased material cost. However, the materials have been continuing expansion in such applications year after year for two decades since then as plant, marine vessel, and housing materials. The course of their development to date has included such proliferation impeding factors as unproved reliability, high production cost, and legal regulations because of being new materials. However, the ardent technical development efforts having produced a number of products including hybrid FRP, particularly the fundamental technology development studies sponsored by the Ministry of International Trade and Industry, have improved properties and reliability and contributed largely to expanding practical applications. Sought in different functions expected in PMC in the future would be application of bionic designs, transfer from functional quality to sensitive quality, and development of material recycling techniques. 8 refs., 11 figs., 1 tab.

  7. Hydrogenolysis reactions characteristics of deashed coal under low temperature; Teionka ni okeru dakkai shoritan no suisoka bunkai hanno tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Owada, T.; Mashimo, K.; Wainai, T. [Nihon University, Tokyo (Japan). College of Science and Technology

    1996-10-28

    In relation to coal liquefaction, the effect of inorganic minerals on liquefaction reactivity and the effect of hydrofluoric acid (HF) treatment on organic molecular structure of coals were studied by demineralization of low-rank coals in HCl or HF solution. In experiment, Taiheiyo coal specimen was deashed in HCl solution at 25-70{degree}C for 6 hours while agitating, and in addition, deashed in HF solution. Hydrogenolysis of the deashed coal specimen was conducted using tetralin or methylnaphthalene as solvent under initial hydrogen pressure of 1.96MPa at reaction temperature of 693K for 60min. The experimental results are as follows. The ash content of Taiheiyo coal hardly offers catalysis in hydrogenolysis reaction. Carboxyl group increases in demineralization of coal because of breakage of bridged bonds. Organic structure of coal changes by demineralization in dense HF solution. Change in organic structure of coal by demineralization in dense HF solution is dependent on treatment temperature. 2 refs., 4 figs., 1 tab.

  8. Studies on reactivity of coal surfaces at low temperature; Teion ni okeru sekitan hyomen no hannosei no kento

    Energy Technology Data Exchange (ETDEWEB)

    Yasuda, H.; Kaiho, M.; Yamada, O.; Soneda, Y.; Kobayashi, M.; Makino, M. [National Institute for Resources and Environment, Tsukuba (Japan)

    1996-10-28

    With an objective to learn reactivity of coal at its surface, surfaces of oxidized coal samples were investigated. Miike coal was oxidized by using {sup 18}O2 in a closed loop system. As the reaction progresses, proportion of CO2 including isotopes increased rapidly as a result of oxidation of CO sites existing in the coal and the newly generated C{sup 18}O sites. The oxidizing reaction progressed via oxygen adsorbing sites generated near the surface, and oxygen containing groups. An FT-IR analysis estimated the depth of the oxidized layer to be 10{mu}m or less from particle surface. The oxidized coal was pulverized to see its surface condition. Functional groups introduced by the oxidation enter into the vicinity of the surface in a form to desorb as CO. CO2 is trapped in inner pores. The coal surface was observed by using an atomic force microscope. No observable openings in the pore structure were discerned on the surface before the oxidation, and the structure agrees with a closed pore model. Surface image oxidized in-situ by oxygen for one hour had slight roundness, which led to a supposition of structural change, and changes in the functional group and adsorption species. 7 refs., 5 figs.

  9. Change of unit skeletons during an artificial coalification; Jinko sekitanka katei ni okeru tan`i kokkaku kozo no henka

    Energy Technology Data Exchange (ETDEWEB)

    Sugimoto, Y.; Miki, Y.; Hayamizu, K. [National Institute of Materials and Chemical Research, Tsukuba (Japan); Okada, K. [Coal Mining Research Center, Tokyo (Japan); Suzuki, Y. [Geological Survey of Japan, Tsukuba (Japan)

    1996-10-28

    In order to obtain knowledge about formation and growth of condensed ring structure in a coalification process, discussions were given on product skeleton structure by using hydrogenation and hydrocracking of heated cellulose. In underwater heating of cellulose, reaction of dehydration has occurred at 200{degree}C or lower, that of decarbonation at 250{degree}C or higher, and that of demethanizing at 300{degree}C, resulting in production of a dark-brown coal-like substance. The substance has lower H/C value and higher O/C value than coal. As the underwater heating temperature rises, the hydrogenation reactivity of the heated substance decreases, and so does the ratio of conversion into toluene solubles. These phenomena are related to strength of cross-linking bond between unit skeleton structures. A substance heated at an underwater heating temperature of 200{degree}C turns toluene-soluble almost completely even during the hydrogenation reaction (350{degree}C for 2 hours), but the soluble product decreases at underwater heating temperatures of 250 and 300{degree}C. However, soluble product of more than 90% was obtained when hydrocracking (at 425{degree}C for one hour) was performed. The toluene-soluble product in the heated substance is only 50% when the underwater heating temperature reaches 350{degree}C even if the hydrocracking is carried out. 3 refs., 5 figs.

  10. Thermophysical properties measurement of high temperature melts under microgravity; Bisho juryokuka ni okeru koon yutai no netsubussei sokutei

    Energy Technology Data Exchange (ETDEWEB)

    Hibiya, T. [NEC Corp., Tokyo (Japan)

    1998-03-20

    This paper introduces an example of the thermophysical property measurement of high temperature melts under microgravity. In addition, this paper also reports the thermophysical property measurement of high temperature melts measured on the ground so as to make preparations for a microgravity experiment. In the microgravity environment, the methodology by which the diffusion constant, heat conductivity, and surface tension previously called `three vices of thermophysical property measurement` can be properly measured was arranged. Frohberg showed a scientific interest in the measurement of a diffusion constant. The research worker in Japan introduces a shear cell method and has been endeavoring to improve the measurement precision. In practical use, the diffusion measurement of semiconductor melts is significant as a research theme. The electromagnetic suspension device (TEMPUS) developed in German enabled the thermophysical measurement in the supercooled state by utilizing the advantage of non-contact. It is a great breakthrough in the thermophysical property measurement of high temperature melts that were difficult to measure. The behavior at the melting point or higher can be properly recognized by examining the properties and structure of supercooled melts. 49 refs., 9 figs., 2 tabs.

  11. Computer-aided fabrication of bridges; Kyoryo seisaku ni okeru CAD-CAM no genjo to kadai

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, N. [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

    1996-08-01

    Described herein is application of the computer-aided CAD/CAM systems to fabrication of bridges from the designs to inspection and production management in the order of production flow. The design works begin with inputting coordinate values for road alignment to determine alignment drawings, coordinates and haunches, and to output the alignment drawings, coordinates, haunches and calculation of haunches and web crest height, and are extended to automatic designs of major girder sections, splices, stiffeners and floor frames, and to preparation of design calculation sheets. As the drawings, although showing bridge characteristics such as completed shapes, are frequently silent on fabricated shapes, the full-size modeling is effected by an automatic program with the additional data regarding welding-induced shrinkage, cambers, joint gaps, allowances for finishing and bore sizes. The CAM systems for fabrication include those for marking, NC marking for cutting, plasma/gas cutters and panel welding robots, which are connected to DNC servers in LAN systems. 6 refs., 14 figs.

  12. Water quality and water pollution sources in Poyang lake, China; Poyang ko ni okeru suishitsu chosa to odakugen kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Ito, M. [Shin-Nippon Meteorological and Oceanographical Consultant Co. Ltd., Tokyo (Japan)

    1996-01-10

    This paper summarizes the current status of water quality and pollution sources in Poyang Lake in China. The lake is located in Chianghsi Province of China, and a largest fresh water lake in China that flows out into the Yangtze river. The basin is surrounded by mountains on three sides and faces the Yangtze on one side, whereas the plains formed by the lake and the rivers flowing in extends in the center of the basin. The plains around the lake has the city of Nanchang, the capital of the province, the city of Jiujiang (both cities have a population of about 4 million, respectively), and four other cities with a size of one million people including Jingdezhen. Water supply system in the basin is used in a 37% area of the urban areas, and no sewage facilities of whatsoever are available as of 1991. The lake has COD of about 3 mg{times}1/l. No severe pollution by organic matters is seen. While the T-P concentration is at a high level, PO4-P is low. Majority of phosphorus flowing into the basin exists in the form trapped in soil particles. In order to maintain the current water quality in the future, waste water treatment is required in the basin. Construction of an oxidation pond in the vast land exposed during the drought period is a measure that can be tackled relatively easily. 1 fig., 4 tabs.

  13. Accuracy of FEM 3-D modeling in the electromagnetic methods; Denjiho ni okeru FEM 3 jigen modeling no seido

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, Y. [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1996-10-01

    Analytical methods considering 3-D resistivity distribution, in particular, finite element method (FEM) were studied to improve the reliability of electromagnetic exploration. Integral equation, difference calculus, FEM and hybrid method are generally used as computational 3-D modeling method. FEM is widely used in various fields because FEM can easily handle complicated shapes and boundaries. However, in electromagnetic method, the assumption of continuous electric field is pointed out as important problem. The normal (orthogonal) component of current density should be continuous at the boundary between media with different conductivities, while this means that the normal component of electric field is discontinuous. In FEM, this means that current channeling is not properly considered, resulting in poor accuracy. Unless this problem is solved, FEM modeling is not practical. As one of the solutions, it is promising to specifically incorporate interior boundary conditions into element equation. 4 refs., 11 figs.

  14. Unsteady performance of a cavitating hydrofoil in stall conditions. Shissoku jotai ni okeru yokukei no hiteijo tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Ogata, H. (Tohoku University, Sendai (Japan)); Ito, Y. (Hachinoe Institutea of Technology, Aomori (Japan)); Oba, R. (Tohoku University, Sendai (Japan). Institute of Fluid Science); Sunayama, Y.; Abe, J. (Suzuki Co. Ltd., Shizuoka (Japan))

    1991-11-25

    To elucidate the unsteady performance of cavitating hydrofoils in a stall condition, this paper describes a survey on unsteady conditions without cavitations and stall conditions as to their characteristics from a cavitation to a supercavitation, lift and drag. Flows with cavitations were also analyzed. As a result of comparing also data for the subcavitation regions, it was found that a large-scale vortex generation on the hydrofoil back-pressure plane in near stall condition has a close relation with the changes in lifts and drags or the cavitation breakdown. The experiment used a testing water tank of circulation flow type having a rectangular measuring cross section (70 mm in width and 190 mm in height), and the hydrofoil specimens of two-dimensional symmetric type with a chord length of 70 mm and an aspect ratio of 1.0. The test condition used a cavitation coefficient of 0.18-6.33 (from a supercavitation to non-cavitation). A numerical analysis proved that the power spectra around the hydrofoils having no cavitations agreed with the experimental results, and verified the reasonability of the application. 18 refs., 8 figs., 2 tabs.

  15. Analysis of flame propagation phenomenon in simplified stratified charge conditions; Tanjunkasareta sojo kyukiba ni okeru kaen denpa gensho no kansatsu

    Energy Technology Data Exchange (ETDEWEB)

    Moriyoshi, Y.; Morikawa, H. [Chiba University, Chiba (Japan); Kamimoto, T. [Tokyo Institute of Technology, Tokyo (Japan)

    1997-10-01

    Since the local inhomogeneity of mixture concentration inside the cylinder affects the combustion characteristics, a basic research on combustion phenomenon in stratified charge conditions is required. The authors have made experiments with a constant-volume chamber, which can simulate an idealized stratified charge field by using a removable partition, to obtain the combustion characteristics. Also, numerical calculations are made using some combustion models. As a result, the important feature that the combustion speed is faster in stratified condition than in homogeneous condition can be predicted by the two-step reaction model. 4 refs., 8 figs.

  16. Analysis of fuel spray characteristics for premixed lean diesel combustion; Kihaku yokongo diesel kikan ni okeru nenryo funmu kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, S.; Harada, a.; Miyamoto, T.; Akagawa, H.; Tsujimura, K.

    1997-10-01

    Premixed lean diesel combustion (PREDIC) makes it possible to achieve low NOx emission. It is an important factor to make the homogeneous spray formation for PREDIC. In this paper presents I the effect of the spray dispersion on emission characteristic were analyzed with the spray observation and engine test. Pintle type nozzle, which has different feature from orifice type nozzle, are used to form the hollow cone spray. As a result, the pintle type nozzle having grooves to generate the swirl flow, makes the reduced penetration in comparison with the hole nozzle under low ambient gas pressure. And it could improve THC, CO emissions at low NOx emission condition. 7 refs., 12 figs., 1 tab.

  17. Interphase boundary structure and transformation mechanism in diffusional phase transformations; Kakusan hentai ni okeru iso kaimen kozo to hentai kiko

    Energy Technology Data Exchange (ETDEWEB)

    Furuhara, T.; Maki, T. [Kyoto University, Kyoto (Japan)

    1997-05-20

    This paper discusses a lattice changing mechanism in diffusional phase transformations (atom diffusion rate determination) based on observations through a high-resolution electron microscope. If a parent phase and a generated phase have different crystal structures, change in lamination occurs as a result of a step generated on a terrace with good consistency moving in the horizontal direction. In addition, it has been thought that removal of atoms occurs due to random diffusion jump in a riser or a kink which has a locally inconsistent structure, and no surface undulations will occur. On the other hand, growth interfaces are consistent in martensite transformation, and atomic correspondence is univocal in the parent phase and the generated phase. Also in diffusion transformation accompanying distribution of displacement type elements, the surface undulations will appear as in the case of the martensite transformation. This fact suggests that, also in the diffusional transformation, not only the terrace interface, but also the riser or kink interface having been thought inconsistent conventionally are all consistent or semi-consistent as in the martensite transformation. It also suggests that lattice correspondence exists between the parent phase and the generated phase. 30 refs., 16 figs., 1 tab.

  18. Superplasticity of low carbon HSLA steel during bainite transformation. Teitanso teigokinko no beinaito hentai ni okeru chososei kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Nakajima, H.; Yamamoto, S.; Miyaji, H.; Furubayashi, E. (National Research Inst. for Metals, Tsukuba, Ibaraki (Japan))

    1993-12-01

    Recently, the development of high strength low alloy steel (HSLA steel) of untempered type is advanced by using the comparatively high strength and excellent tenacity of the bainite or martensite of carbon remained being transformed. In the present researches, the superplasticity during the bainite transformation due to the continuous cooling and changes of the structure as well as the mechanical properties due to the superplastic deformation are examined with the samples of Mn-Cr-Mo system HSLA steel. The results obtained therefrom are shown as follows. The temperatre range of B[sub S] and bainite transformation is moving to the higher temperature side along with the increasing of the applied stress when it is over 60 MPa. The bainitic structure is composed of the mixture lath-like bainitic ferrite and granular bainitic ferrite in the use of having no applied stress, while the percentage of the latter increases simultaneously with the increasing of the applied stress. Transformation superplastic strain is increasing together with the increasing of the applied stress, and its increasing is over the linear function when the applied stress is above about 50 MPa. 22 refs., 9 figs., 2 tabs.

  19. Automation and high-efficiency of welding in pipeline; Gas pipeline ni okeru yosetsu no jidoka to konoritsuka

    Energy Technology Data Exchange (ETDEWEB)

    Kawanishi, N.; Masuda, H.; Hara, Y.; Kimura, M. [Osaka Gas Co. Ltd., Osaka (Japan); Iimura, M. [Tokyo Gas Co. Ltd., Tokyo (Japan); Hayashi, K. [Toho Gas Co. Ltd., Nagoya (Japan); Mori, K.; Suesawa, S. [Japan Gas Association, Tokyo (Japan)

    1997-11-01

    With objectives to develop technologies which can perform a welding work automatically at ultra-high speed, improve efficiency in construction works of building town gas transporting pipelines, and make the welding quality uniform, a program that will last for six years has been established to make necessary discussions. Using a horizontally fixed pipe, AP15L-X65, with a diameter of 750 mm and a plate thickness of 19 mm as the object of the discussions, the following four welding processes were selected to implement the development on each process in parallel: high-speed TIG welding, high-speed oscillating MAG welding, plasma welding, and electron beam welding. In March 1997 by which the former half of the project has been completed, an arc time of less than 30 minutes has been achieved as one of the development targets. Using sizes of problems in innovativeness in technologies, welding quality, and practical application as criteria for an interim evaluation, focuses were directed on four technologies. As a result, the electron beam welding was selected, which has achieved an epoch-making result in arc time while maintaining good quality. In the latter half of the project which will end in March 2000, promotion efforts will be continued for discussing how to solve problems in electron beam welding machines, and making developments and field tests thereon. 7 refs., 20 figs., 5 tabs.

  20. Development of automated power distribution technology at Hitachi Ltd; Hitachi Seisakusho ni okeru haiden jidoka no gijutsu kaihatsu no torikumi

    Energy Technology Data Exchange (ETDEWEB)

    Hayami, M.; Matsui, Y. [Hitachi, Ltd., Tokyo (Japan)

    1997-07-01

    The outline and its future expansion of an automated power distribution system that Hitachi is presently developing as the technology supporting the diversified power distribution operation are described. With the progress of distribution technology, a dispersed distribution power system has been recently configured based on the conventional integrated system. As the features of this system, reliability is obtained in the monitor and control sections by a real-time server, and user-friendly operation is ensured in the man-machine processing section by a general-purpose workstation. A `distribution line insulation monitor system` that detects the fore-earth generation in units of sections, a new `22 kV automation system,` and a `distribution facility plan-supported system` to which load flexibility theory was applied based on AI and fuzzy theory have been mainly developed in recent years. With the relaxation of regulations, the development of distributed power linkage equipment will be promoted in future to meet the new situation. 2 figs.

  1. Automatic system of dam grouting in Tenjin dam construction works; Tenjin damu kensetsu koji ni okeru gurauchingu no jidoka system

    Energy Technology Data Exchange (ETDEWEB)

    Imanaga, K.

    1996-03-01

    Since construction management of grouting is controlled by many factors like operators` technical skill and experience, grouting quality is not expected to be good and random and deteriorated quality is feared. Reduction of random quality with different operating individuals and prevention of simple miss due to human errors are expected to be necessary factors to ensure stable quality. Automatic system for Tenjin dam`s grouting quality is developed and its outline is reported in this research study. Considering grouting system`s flow and system`s drawing, grouting automatic system`s summary is explained. Again present grouting automatic system is compared with past systems reported in literature. Then operating personnel cut down in automation of grouting, artificial miss prevention in automatic supplement judgement system, needed time reduction in supplement decision and labor saving are made it possible. Details of above mentioned points are illustrated clearly. 7 figs., 1 tab.

  2. Automatic pipe installation system for pipe jacking method; Suishin koho ni okeru tatekuinai sagyo jidoka system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Hatayama, E.; Sugimoto, H. [Okumura Corp., Osaka (Japan)

    1994-11-15

    A system intended of automating the pipe installation work in tunnels in urban areas was developed, and applied to a site of the mud water propulsion construction. The system automates delivery and connection works of hume pipes. The system includes the following three devices: a delivery device consisted of two hoists running in the propulsion direction and a slinging device, an installation device consisted of two pairs of pipe receiving rollers to load hume pipes at the pipe installing side and the main pushing device side, and a control device consisted of an operation monitoring panel and an operation working box. The following results were obtained from factory experiments: the hume pipe deflection was within {plus_minus} 10 mm, the movement stopping accuracy within {plus_minus} 20 mm, the difference in lifting and lowering works of the two hoists within {plus_minus} 10 mm, and the accuracy in positioning the pipe receiving rollers within {plus_minus} 1 mm, all being satisfactory. The following results were obtained when the system was applied to a site using the mud water propulsion method: manual works were eliminated, and the safety was improved; the performance of the positioning function is so high that the work efficiency was improved; and one operator on the ground can operate the system easily, thus having achieved the manpower saving. 12 figs., 1 tab.

  3. Automatic construction management of inclined cable in Heira bridge; Heirahashi ni okeru syazai keburu seko kanri no jidoka

    Energy Technology Data Exchange (ETDEWEB)

    Kajiyama, K.

    1996-03-01

    First one sided PC inclined cable bridge based on precast block additional method is constructed at Heira in Japan. Measurements of main girder deflection and main tower displacement values are considered as necessary factors in construction of inclined cable bridge. Efficient and rapid tension force supervision of inclined cable in every stage of construction is required for the above mentioned purpose. Automatic management of tension of inclined cable in Heira bridge construction is considered in this investigation. Construction of measuring system, installation, tension force adjustment and its decision management process, required special characteristics of tension, calculation sheet`s process et., are explained. Following observations are noted when precast method is compared with cast in place method for Heira bridge. Construction cycle of main girder is small and cycle until end of tension for 1 block construction to last block construction is equal to 1.6/day/block. 12 figs., 1 tab.

  4. Examples of automated material handling systems for iron and steel works; Tekko denroyo ni okeru jidoka butsuryu system no jirei

    Energy Technology Data Exchange (ETDEWEB)

    Tamura, Y.; Sugimoto, T.; Kimura, M.; Kudo, M. [Hitachi, Ltd., Tokyo (Japan)

    1996-06-01

    The iron and steel industry in which reduction in production cost and improvement in quality management are the most important problem has positively introduced systems to identify material flows in a factory on a real-time basis and achieve power saving in material moving. This paper shows a sequence of introducing a material handling system proposed by Hitachi, Ltd., introduces examples of the actual installations, and describes the latest material handling automation technology. Examples of actual installation may include a case of automating a scrap yard. In the case, work of unloading materials delivered on trucks of unspecified shapes is separated from a work to move them into and from a warehouse in the yard, or a buffer hopper is installed to level out operation time of cranes. Thus, automation and on-line use of information were achieved upon changing the yard work procedure. For example, load weight on a hopper is taken in on a real-time basis to use the result for controlling the number of deliveries out from a warehouse, improving the mixing accuracy, and managing the inventory information. 6 refs., 4 figs.

  5. Improvement of automatic weld and productivity in orbital pipe welding; Pipe yosetsu ni okeru saikin no jidoka to kosokuka

    Energy Technology Data Exchange (ETDEWEB)

    Imaizumi, H.

    1996-09-01

    This paper presents the trend of automatic pipe welding technology and high-speed welding for resolving a lack and aging of welding engineers. In pipe TIG arc automatic welding, precise motor servo control and reproducibility are required to secure ideal penetration bead welding, and such requirements have already beeb satisfied since 20 years ago. However, in MAG welding, since heat gain too high delays cooling of metal melt and causes undercut on the inner wall of pipes, the above requirements are very difficult to be satisfied except the thick pipe for which cooling copper strips are available as inner backing. The proper welding effect was thus obtained by widely controlling the output waveform of welding machines to secure the same heat gain as TIG arc welding. Favorable penetration bead welding was thus achieved even for thin pipes. In order to cope with automatic welding needs in the clearance between thin pipes, specifications of welding heads were subdivided, and a power source unit, computer control unit and cooling water circulation unit were integrated for automation. 7 figs., 7 tabs.

  6. Low-temperature hydrothermal reaction of mullite in sodium; Suisanka natoriumu yoeki ni okeru muraito no teionsui netsuhanno

    Energy Technology Data Exchange (ETDEWEB)

    Li, Keqin; Igarashi, Kaoru; Shimizu, Tadao [Chiba Institute of Technology, Chiba (Japan). Department of Industrial Chemistry

    1999-08-10

    Hydrous sodium aluminosilicate was formed when mullite powder of high purity prepared by alkoxide method was hydrothermally treated with sodium hydroxide aqueous solution. The hydrous sodium aluminosilicates were mainly composed of 1.08Na{sub 2}O {center_dot} Al{sub 2}O{sub 3} {center_dot} 1.68SiO{sub 2} {center_dot} 1.8H{sub 2}O and Na{sub 14}Al{sub 12}Si{sub 13}O{sub 51} {center_dot} 6H{sub 2}O in spherical grains. Successively, a small amount of Na{sub 3}Al{sub 3}Si{sub 3}O{sub 12} {center_dot} 2H{sub 2}O was observed at the final stage. The ratio of Al{sub 2}O{sub 3}/SiO{sub 2} in the mullite had an influence on the kind of products besides treatment temperature and time. ICP (Induced coupling plasma) analyses indicated that more Al in the mullite was dissolved into the solution than Si. At the beginning of reaction, boemite was precipitated. The SiO{sub 2} rich mullite was positively formed Na{sub 6}Al{sub 6}Si{sub 10}O{sub 32} {center_dot} 12H{sub 2}O instead of boemite. (author)

  7. Remote reference processing in MT survey using GPS clock; MT ho ni okeru GPS wo mochiita jikoku doki system

    Energy Technology Data Exchange (ETDEWEB)

    Yamane, K.; Inoue, J.; Takasugi, S. [Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Kosuge, S. [DRICO Co. Ltd., Tokyo (Japan)

    1996-05-01

    A report is given about the application of a synchronizing system using clock signals from GPS satellites to a remote reference method which is a technique to reject noise from the MT method. This system uses the C/A code out of the L1 band waves from NAVSTAR/GPS satellites. The new system was operated in MT method-using investigations conducted at China Peninsula, Aichi Prefecture, and Izu Peninsula, Shizuoka Prefecture, with the reference points placed several 100km away in Iwate Prefecture on both occasions. It was found as the result that it is basically possible to catch signals from the GPS at any place, that the signals are accurate enough to be applied to time synchronization for the MT method, and that the signals assure a far remote reference method with a separation of several 100km between the sites involved. The referencing process at high frequencies whose feasibility had been doubted proved a success when highly correlated signals were exchanged between two stations over a distance of several 100km. 5 refs., 9 figs.

  8. Magnetic constraints of basement structure offshore of western Kyushu, Japan; Kyushu seiho kaiiki ni okeru jiki ijo no kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Okuma, S.; Nakatsuka, T. [Geological Survey of Japan, Tsukuba (Japan); Ishihara, T. [Japan National Oil Corp., Tokyo (Japan)

    1996-05-01

    This paper describes the results from the qualitative analysis of magnetic anomalies offshore of western Kyushu and from an analysis by a three-dimensional two-layer model inversion. The analysis ranged from Kyushu on the east to Jeju Island on the west and from the southern part of the Korean Peninsula on the north to Tanegashima and Yakushima Islands on the south, namely, the area of 580km from east to west and 580km from south to north. The analytical data used was Magnetic Anomaly Map of Asia (GSJ and CCOP, 1994). In the qualitative analysis, a pseudogravity anomaly map and a pole gravity anomaly map were prepared from the total magnetic force anomaly map by means of a frequency filter operation. As a result, it was noted that two distinctive magnetic high belts existed in the margin of the Tunghai Shelf, extending from the sea area to the west of the Nansei Islands continuously to NNE, and being distributed transversely through the Goto sedimentary basin. Additionally, in the inversion analysis, it was demonstrated that the magnetic basement became shallow at the margin of the Tunghai Shelf north of latitude 31 degrees north, extending nearly in the NNE direction through west of the Goto Islands, west of Tsushima Island, and continuing to the southern coast of the Korean Peninsula. 6 refs., 4 figs.

  9. 1000m depth boring at Inagawa, Hyogo prefecture. 1. Overviews; Hyogoken Inagawamachi ni okeru 1000m boring chosa. 1. Gaiyo

    Energy Technology Data Exchange (ETDEWEB)

    Sato, T.; Kusunose, K.; Cho, A.; Tosha, T. [Geological Survey of Japan, Tsukuba (Japan); Kiyama, T.; Yamada, F. [Mitsui Construction Co. Ltd., Tokyo (Japan); Aizawa, T. [Sancoh Consultants Co. Ltd., Tokyo (Japan)

    1996-05-01

    Various field experiments were carried out using a 1000m deep borehole at Inagawa town, about 10km north of the focus of the Hanshin-Awaji Great Earthquake and directly above the area where shallow earthquake activities have intermittently occurred. These experiments included stress measurement by hydraulic fracturing, hydrophone-aided VSP, permeability tests and observation of various types of logging. The laboratory experiments were also carried out, including measurement of various properties and stresses of the core samples. The stress-depth relationship, determined by the hydraulic fracturing method, shows that the stress gradient well coincides with the Western Japan standard at a depth up to 700m, whereas it is approximately twice as high as the standard at a depth of 946m, at which core disking and borehole break-out are clearly observed, and hence stresses conceivably concentrate locally. Orientation of the maximum horizontal compressive stress is E-W at a depth of around 600m, but greatly changes to NNW-SSE at a deeper position. 4 refs., 5 figs.

  10. MT2-D inversion analysis in Kakkonda geothermal field; Kakkonda chinetsu chiiki ni okeru MT ho nijigen kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Yamane, K.; Takasugi, S. [Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Miyazaki, S. [Japan Metals and Chemicals Co. Ltd., Tokyo (Japan); Uchida, T. [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

    1996-05-01

    Data, collected from an MT method-assisted survey conducted in the Kakkonda geothermal region in 1987, was re-examined, and a new structure was found. The review was carried out by use of a 2D analysis in the TM mode. According to the 1D analysis of 1987 and the geological data gathered then, it is estimated that the resistivity structure of this region runs in the northwest-southeast direction. A northeast-southwest traverse line was set for this analysis, orthogonal to the strike, and the impedance at each observation spot was caused to rotate to this direction across the whole range of frequency. Furthermore, in 1994-95, surveys were conducted using arrayed CSMT/MT methods. All these sum up to indicate that a high-resistivity region extends northwest in the southwestern part of the Kakkonda river but that there exists a low-resistivity region of several 10 Ohm m centering about the B traverse line. The high-resistivity region deep in the ground being the target of excavation in the Kakkonda region, to collect knowledge about this high-resistivity is important, and here the effectiveness of the 2d analysis has been verified. 5 refs., 11 figs.

  11. Water balance of the oceans and the large rivers in the world. Sekai no daikasen to kaiyo ni okeru mizushushi

    Energy Technology Data Exchange (ETDEWEB)

    Oki, T.; Mushiake, K. (The University of Tokyo, Tokyo (Japan). Institute of Industrial Science)

    1993-07-01

    Data for water balance of river basins and oceans were used for an investigation made on the annual water balance, especially on ratios of evaporation to precipitation, standing on global water circulation standpoint. The world river water balance data were used to seek classification of 70 river basins and precipitation amounts by preparing ground surface topographical data based on materials published by the National Geophysical Data Center (NGDC). The river water flow investigation used digital data published by the Global Runoff Data Center (GRDC). River water balance by oceans and lands in the world was calculated. This is an annual sum of atmospheric steam convergence, precipitations, evaporation calculated from the atmospheric water balance, and water runoff from lands into oceans. The paper shows on about 70 large rivers in the world their annual water balance, positions of estuaries in river basins, and amounts of precipitation and evaporation. Tropical areas have abundant precipitation, with evaporation efficiency at about 50%, while subtropical areas have majority of their precipitation evaporate, with very little runoff. 8 refs., 4 figs., 1 tab.

  12. Shallow seismic reflection prospecting in Hachiro-kata reclaimed land; Hachirogata kantakuchi ni okeru senbu hanshaho jishin tansa

    Energy Technology Data Exchange (ETDEWEB)

    Kitsunezaki, C.; Fukutome, T.; Matsumoto, S.; Noda, K.; Sato, T. [Akita University, Akita (Japan). Mining College; Hayashi, H.; Ishii, E.; Yamanaka, Y.; Matsuno, K.; Mikuni, S. [Suncoh Consultant Co. Ltd., Tokyo (Japan)

    1997-05-27

    Along the Japan Sea coast in Akita Prefecture and in the vicinity, there exist active fault groups, such as the Kitayuri thrust fault group in the south and Noshiro thrust fault group in the north. It is estimated that there is another fault, running from Akita City located between the above-said two thrust fault groups into the Hachiro-kata reclaimed land, roughly connecting the two thrust fault groups. This third fault is supposed to be related to the hypocenter of Tencho Earthquake of 830, but its location and structural configuration are not known, and it is not known whether it is an active fault, either. Investigations are conducted using S- and P-waves. The greatest problem in the use of P-waves is that there exists a layer in which signal attenuation is high and transmission is anomalously slow. This problem is ascribed to the layer pore water rendered unsaturated though slightly by the inclusion of air bubbles, and is explained for the most part by the White model. A survey using S-waves is advantageous in that it does not experience no difficulty of this kind. In the P-wave cross section, a structure supposed to be an inversion layer is observed at a level deeper than 200m. In the case of the S-wave method, more details of the shallow structure will be available when the degree of CMP stacking is augmented as usual. 2 refs., 9 figs., 1 tab.

  13. Fault analysis in the very shallow seismic reflection method. 2; Gokusenso hanshaho ni okeru danso kaiseki. 2

    Energy Technology Data Exchange (ETDEWEB)

    Nagumo, S.; Muraoka, S.; Takahashi, T. [Oyo Corp., Tokyo (Japan)

    1997-05-27

    Fault analysis is required in addition to the ordinary process of structural analysis (CDP stacking) for the examination of discontinuity in the reflection horizon in question. The fault shape restoration principle is that the reflection point of a reflection wave observed at a certain receiving point is on an ellipse with the shock point and receiving point at its focal points and that the sum of the distances between the reflection point and the focal points is equal to the reflection wave propagation time. The DMO velocity is worked out by calculation using the positive travel time and inverse travel time from the common reflection surface. When the reflection surface is inclined by {theta}, the average interval velocity/cos{theta} is called the DMO velocity. When the reflection surface inclination and the average interval velocities are determined separately in this way, the position of the reflection point may be worked out, and this enables the calculation of the amount of migration (lateral movement). The reflection wave lineups carried by the original record are picked up one by one, and the average interval velocities are treated very prudently. After such a basic DMO conversion treatment, the actualities of the fault are described fairly correctly. 3 figs.

  14. Relation between frequency of seismic wave and resolution of tomography; Danseiha tomography kaiseki ni okeru shuhasu to bunkaino no kankei

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, M.; Watanabe, T.; Ashida, Y.; Sassa, K. [Kyoto University, Kyoto (Japan). Faculty of Engineering

    1997-05-27

    With regard to the elastic wave exploration, discussions have been given on the relationship between frequency and resolution in P-wave velocity tomography using the initial travel time. The discussions were carried out by using a new analysis method which incorporates the concept of Fresnel volume into tomography analysis. The following two arrangements were used in the calculation: a cross hole arrangement, in which seismic source and vibration receiving points were arranged so as to surround the three directions of a region extending 250 m in the horizontal direction and 500 m in the vertical direction, and observation is performed between two wells, and a permeation VSP arrangement in which the seismic source is installed on the ground surface and receiving points installed in wells. Restructuring was performed on the velocity structure by using a total of 819 observation travel times. This method has derived results of the restructuring according to frequencies of the seismic source used for the exploration. The resolution shown in the result of the restructuring has become higher as elastic waves with higher frequency are used, and the size of the structure identified from the restructuring result has decreased. This fact reveals that sufficient considerations must be given on frequencies of elastic waves used according to size of objects to be explored. 4 refs., 4 figs.

  15. Measurement results of BHTV logging at the geothermal well. 1; Chinetsusei ni okeru BHTV kenso no sokutei kekka. 1

    Energy Technology Data Exchange (ETDEWEB)

    Lin, S. [Geophysical Surveying and Consulting Co. Ltd., Tokyo (Japan); Nakanishi, S.; Shimizu, I. [Electric Power Development Co. Ltd., Tokyo (Japan)

    1997-05-27

    In association with excavation of the No. 135 steam producing well in the Onikubi geothermal power plant in Miyagi Prefecture, shapes of production zones and drilling-induced fracture (DIF) were acquired from the borehole televiewer (BHTV) data. The BHTV logging shoots sound waves onto well walls of wells filled with fluid and detects the reflection waves to investigate the state of the well walls. Vertical fracture with opening lengths from 2 to 3 m were found at depths of about 1232 m and 1312 m. Water run-off has occurred at a depth of about 1312 m during the excavation, to which these vertical fractures might have contributed possibly. In depths of about 1232 m and 1312 m, fractures inclining toward north-east direction and south-west direction are predominant. Some fractures in the depth of about 1333 m incline toward east-south-east direction and west-north-west direction. Fracture inclination azimuth in all of the present logging sections is predominantly in north-east direction and south-west direction. When the DIF is considered to show the maximum compression azimuth, the earth`s crust stress azimuth is generally in east-west direction, which crosses slightly obliquely with the running direction of the predominant fracture in this well. 1 ref., 7 figs.

  16. Deep sedimentary structure model beneath the Osaka plain; Osaka heiya ni okeru shinbu chika kozo no model ka

    Energy Technology Data Exchange (ETDEWEB)

    Miyakoshi, K.; Kagawa, T.; Echigo, T. [Osaka Soil Test, Osaka (Japan)

    1997-05-27

    Restructuring was carried out on a sedimentary basin structure model of the Osaka plain including Osaka Bay by using newly obtained underground structural data. After the Hygoken-nanbu Earthquake of 1995, a large number of underground structure investigations have been performed in Osaka Bay and urban areas of Kobe and Osaka. However, very few surveys have been done in areas peripheral to Osaka Prefecture, such as the Ikoma area. Therefore, an attempt has been made to increase the number of measuring points to acquire underground structural data of these areas. Estimation of basic rock depths has utilized the dominant cycles in H/V spectra obtained from micro vibration survey, and good correlation of the base rock depths derived by a refraction exploration and a deep-bed boring investigation. With regard to bed division and P- and S- wave velocities in sedimentary beds in the Osaka sedimentary basin, an underground structure model was prepared, which was divided into four beds according to the refraction exploration and the micro vibration investigation. Data obtained by using this model agreed well with depth data acquired from physical exploration and other types of investigations. However, no good agreement was recognized in the data for such areas where the basic depth changes abruptly as the Rokko fault and the Osaka bay fault. 6 refs., 8 figs., 2 tabs.

  17. 3D seismic experiment in difficult area in Japan; Kokunai nanchiiki ni okeru sanjigen jishin tansa jikken

    Energy Technology Data Exchange (ETDEWEB)

    Minegishi, M.; Nakagami, K.; Tanaka, H. [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-05-27

    Difficult area in this context means an exploration-difficult area supposed to store oil/gas but retarded in exploration for the lack of knowledge about the geological structure due to poor quality of available seismic survey records. Discussed in this paper is a survey conducted into an area covering the southern part of Noshiro-shi, Akita-ken, and Yamamoto-cho, Yamamoto-gun, Akita-ken. An area size suitable for data collection at a target depth of 2500m is determined using an interpretation structure compiled on the basis of available well data and 2D seismic survey data. The plan for siting shock points and receiving points is modified case by case as restrictive factors come to the surface (resulting from the complicated hilly terrain, presence of pipes for agricultural water, etc.). The peculiarities of seismic waves in the terrain are studied through the interpretation of the available well data and 2D seismic survey data for the construction of a 3D velocity model for the confirmation of the appropriateness of the plan for siting shock points and receiving points. Efforts are exerted through enhanced coordination with the contractor to acquire data so that a technologically best design may be won within the limits of the budget. The quality of the data obtained from this experiment is in general better than those obtained from previous experiments, yet many problems remain to be settled in future studies about exploration-difficult areas. 4 refs., 4 figs., 1 tab.

  18. Spectral gamma-ray survey of alkaline igneous complex; Arukari kasei fukugo gantai ni okeru ganma sen supekutoru tansa

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, Mitsuo; Karim, T.; Naseer, M. A.

    1999-02-01

    Spectral gamma-ray survey is applied to the investigation of Ambela-Koga-Naranji Kandao igneous complex in Peshawar region in the North of Pakistan located in the northwest edge of the Indian Subcontinent. As a result, quartz syenite-granite, nepheline syenite and phenacite carbonatite rocks respective exhibit gamma-ray spectral anomalies. All the rocks can be identified and characterized easily by gamma-ray spectrums using eU-eTh diagram. Further, on the basis of the obtained gamma-ray spectral anomalies, the evaluation of the storing potential of are earth resources in the same region was attempted. (translated by NEDO)

  19. Cracking control in mass concrete for three gorges dam; Sankyo damu ni okeru masu konkurito no hibiware yokusei

    Energy Technology Data Exchange (ETDEWEB)

    Chu, CHuanying

    1999-09-10

    The provisional cofferdam work of the mainstream of Three Gorges Dam project was successfully finished on November 8, 1997. Now, the work enters its second stage, and the placing of large-scale concrete was started. The total quantity of concrete used in this project reaches 15.00 million m{sup 3}. Inhibition of dam concrete cracking is an important subject. In order to manufacture concrete with good crack-resistance, cements, fly ashes, aggregates and blending agents are strictly selected; and hydration-generating heat is reduced by means of strict temperature control, precooling of aggregates, reduction of placing temperature and concrete temperature in mixers, and the like. As a consequence of maintaining the highest temperature value in concrete blocks to be lower than a predetermined value, harmful cracks can be prevented from occurring when the temperature in the dam lowers. (NEDO)

  20. Feasibility study on introducing new energy systems into Asian villages; Asia sonraku ni okeru shin energy donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For improvement of living standards in unelectrified areas of Asia, the feasibility of new energy power generation systems was surveyed. The degree of electrification of local areas is different every country, and Thailand is ahead of other countries, while Laos and Cambodia are most unelectrified. Power supply of 100W/house seems to be adequate for local areas because of weather condition, housing situation and life-style. Economic support and education on electricity are necessary for poor areas. Although needs for new energy is increasing, the priority is given to industrial and urbanized areas because of cost and investment effects, and remote areas are dependent on grant- in-aid. Resources of photovoltaic, wind power and micro- hydraulic energies are abundant, however, selection of energy and verification of its usability are important, and the local energy density maps were thus prepared. In introduction of new energy, after selection of energy suitable for an area concerned, such geographical and social conditions should be surveyed as road condition, water rights, land utilization, economic support system, policy and intention of inhabitants. 76 refs., 68 figs., 91 tabs.

  1. Earthquake resistant measures of existing structures by TRTA; Eidan chikatetsu ni okeru kisetsu doboku kozobutsu no taishin taisaku

    Energy Technology Data Exchange (ETDEWEB)

    Miyata, N.

    1997-08-10

    Seismic countermeasures for the existing structures are introduced on the main item: reinforcement of open-cut tunnel RC center pillars as well as on reinforcement of rigid frame viaduct pillars and installation of a device for prevention of viaduct falling. First, for reinforcing open-cut tunnel center pillars, design was devised so as to be suitable to construction environment in the subway yard. Important reinforcement materials are steel and filling materials; SS and a self-leveling material for building construction were chosen. The following construction work procedures are explained based on the actual construction: removal of interior materials of existing pillars and measurement of the actual size, high pressure water washing, steel plate fabrication, plate delivery to the yard, installation of steel plates, filler filling, painting. Next, on reinforcement of viaduct pillars on the ground, the reinforcement design concept is basically same as in the open-cut tunnel. Points of difference in design and construction are explained. On the countermeasure for prevention of viaduct falling for girder bridges without the falling prevention, countermeasure investigation and design work or installation work are being carried out. Seismic resistance evaluation and design of existing bridges, and construction work are explained. 13 figs., 1 tab.

  2. Microbially influenced corrosion on stainless steels in natural seawater; Kaisuichu ni okeru sutenresu ko no biseibutsu fushoku

    Energy Technology Data Exchange (ETDEWEB)

    Amaya, H.; Miyuki, H. [Sumitomo Metal Industries Ltd., Osaka (Japan)

    1995-04-05

    The influence of microbes on the corrosion of steels in natural seawater is introduced laying stress on elucidated points. Biofilm consisting of various kinds of microbes is formed on the surface immersed in natural seawater. Adhered bacteria in this biofilm are isolated, and corrosion potential (Ecorr) in an experimental pure cultured system has been also investigated. Metabolic reaction of bacteria plays a part in microbially influenced corrosion (MIC), and reproduction of ennoblement of Ecorr is attempted by artificial means which simulates the breathing reaction of bacteria using refined oxidizing enzyme. It is made clear that corrosion behavior in natural seawater can be reproduced experimentally in a short period of time. This test method simulates the environment of the actual natural seawater well, and environmental MIC can be easily reproduced, which has been difficult in tests where conventional isolated bacteria are employed. 32 refs., 6 figs., 2 tabs.

  3. Current status of development of geothermal power generation in Japan; Nippon ni okeru hatsuden no tame no chinetsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yamaguchi, F.; Esaki, Y. [Japan Geothermal Energy Association, Tokyo (Japan); Oishi, K. [Fuji Electric Co. Ltd., Tokyo (Japan)

    1995-09-15

    The paper reports the situation of geothermal power plants in Japan, future plans, and the research status of geothermal development technology. As for the present situation, explanations were made of each place of development covering Hokkaido to Kyushu and of each developmental organization. Since 1966 when the geothermal power plant started its commercial run, eleven plants and twelve units are presently in operation with a total approved capacity of 298,705 MW. Further, in two years six plants of 230 MW capacity are planning to start operation one by one, and a capacity of 529 MW are expected for 1996. From a viewpoint of developing domestic energy, the government set a target of geothermal supply at 600 MW in 2000 and at 2800 MW in 2010, conducting surveys for geothermal power generation, improving the subsidy system, and promoting the research development. The present target, 530 MW, is equivalent to only 0.27 % of the power generated from power plants in Japan. Geothermal energy is a valuable domestic energy, and therefore, both governmental and private efforts are being exerted for the development. 3 refs., 2 figs., 7 tabs.

  4. Improvement of vehicle stability in cornering on uneven road; Akuro senkaiji ni okeru sharyo no anzensei kojo

    Energy Technology Data Exchange (ETDEWEB)

    Tobimatsu, K.; Harada, M.; Harada, H. [National Defense Academy, Kanagawa (Japan)

    1997-10-01

    The active control of vehicle suspensions and rear wheel steering systems in turning on uneven roads is analyzed by means of LQR control theory, assuming that cornering forces depend on tire normal loads in addition to tire slip angles. The authors quantitatively investigated the effectiveness of the integrated control of the active suspension and the rear wheel steering, comparing the contributions of each individual system. Furthermore, in this paper, the role of the chassis control and driver control are studied in order to improve the stability of vehicle motion disturbed by the road surface. 4 refs., 9 figs.

  5. Measurement improvements of heat flux probes for internal combustion engine; Nainen kikan ni okeru netsuryusokukei no kaihatsu to kento

    Energy Technology Data Exchange (ETDEWEB)

    Tajima, H.; Tasaka, H. [Miyazaki University, Miyazaki (Japan)

    1997-10-01

    In heat flux measurement in engines, material properties of a heat flux probe and numerical prediction of those influence have been discussed rather than practical measurement accuracy. This study featured the process for the quantitative examination of heat flux probes. Although the process required direct comparison among all the probes and additional measurements in a constant volume bomb, precision of heat flux measurement was greatly improved so that the essential characteristics of heat transfer in engines can be detected. 9 refs., 8 figs., 1 tab.

  6. Simulation of speed control in acceleration mode of a heavy duty vehicle; Ogatasha no kasokuji ni okeru shasoku seigyo simulation

    Energy Technology Data Exchange (ETDEWEB)

    Endo, S.; Ukawa, H. [Isuzu Advanced Engineering Center, Ltd., Tokyo (Japan); Sanada, K.; Kitagawa, A. [Tokyo Institute of Technology, Tokyo (Japan)

    1997-10-01

    A control law of speed of a heavy duty vehicle in acceleration mode is presented, which is an extended version of a control law in deceleration mode proposed by the authors. The control law is based on constant acceleration strategy. Using the control law, target velocity and target distance can be performed. Both control laws for acceleration and deceleration mode can be represented by a unified mathematical formulae. Some simulation results are shown to demonstrate the control performance. 7 refs., 9 figs., 2 tabs.

  7. Model of syllable confusion in sound fields with single reflection; Tan`itsu hanshaonba ni okeru onsetsu icho model

    Energy Technology Data Exchange (ETDEWEB)

    Korenaga, Y. [Kajima Corp., Tokyo (Japan)

    1995-12-20

    This paper introduces findings on the human auditory organ involved in voice information processing and its function, and describes a discussion on perception of syllables in the cerebrum and on the identifying process of syllables. A model of syllable confusion was proposed from a viewpoint of voice processing in the auditory organ. In addition, a syllable confusion estimation expression was proposed that is defined by an inter-syllable distance measure that reflects dynamic features of voice in addition to static features of voice. In order to verify the effectiveness of the syllable confusion model and the accuracy of the confusion estimation expression, a sound field with single reflection was used to compare the measured values and the estimated values of the degree of confusion. The single reflection sound field in the estimation was synthesized in a computer by using template syllable data. As a result, it was found that this syllable confusion model has identified nearly completely the syllable hearing characteristics of a human body. Improving further the estimation accuracy of the model requires discussions on automatic gain control in the middle ear and the inner ear, side suppressing function in the inner ear, non-linearity in cochlea filter, and auditory masking. 21 refs., 7 figs.

  8. Research and Development of Coal Conversion Technologies on the New Sunshine Program; Nyusanshain keikaku ni okeru sekitan tenkan gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Sugawara, Akira.; Kurosawa, Shigeru.; Yasuda, Hajime.; Hatori, Hiroaki.; Sugiura, Takashi.; Saito, Kazufumi. [Agency of Industrial Science and Technology, Tokyo (Japan)

    1999-02-20

    Agency of Industrial Science and Technolgy (AIST) has been conduction R and D on coal conversion technologies in Japan. New energy and Industrial Technology Development Organization (NEDO) has been carrying out some R and D projects on soal liquefaction and gasification as a part of (New Sunshine Program) lead by AIST. Coal liquefaction and gasification are mejor concern for NEDO and the overview od the R and D projects up-dated is presented in this paper. In additition, new concept and ambition of R and D on coal aonversion technologies are also outlined. (author)

  9. Permeability prediction in a carbonate reservoir, Middle East; Tansan`en gan`yuso ni okeru shintoritsu no suisoku

    Energy Technology Data Exchange (ETDEWEB)

    Masuzawa, T. [Japan National Oil Corp., Tokyo (Japan); Tani, A. [Fuji Research Institue Corp. Tokyo (Japan)

    1997-11-01

    The reservoir characterization is used in a narrow sense as the meaning of predicting how the parameters of rock property distributes in an oil reservoir. In this study, a method for estimating the well permeability, specially for estimating the horizontal permeability distribution of no core well, that is indispensable for the oil reservoir characterization, is studied using core data and log data. Then, the permeability is estimated by using two methods, the neural network method and the multiple linear regression analysis method, and the estimated values of the two methods are compared with the results of permeability prediction obtained by {phi}-K correlation which has been traditionally used. Furthermore, which method among them is suitable to the oil reservoir is discussed. In this study, the accuracy of the permeability estimated by these three methods are not very high. That the object of this stud is an oil reservoir consisted of carbonate may be considered as an important reason for the low accuracy due to its complicated nature. 10 figs.

  10. System and equipment of aspetic package for food industry; Shokuhin kogyo ni okeru mukin packaging no system to kiki

    Energy Technology Data Exchange (ETDEWEB)

    Minoura, S. [CKD Corp., Nagoya (Japan)

    1996-12-27

    This paper describes aseptic package systems for food industry. In-line type aseptic packaging machine is composed of a sterilizing unit, sterile chamber and handling machines. The sterilizing unit is composed of a superheated steam circuit, a tank for storing and a pump for circulating hydrogen peroxide, and a circuit for preparing, superheating and cooling sterile air. The sterile chamber is kept under sterile positive pressure condition by steam generated in the sterilizing unit, hydrogen peroxide and sterile air before operation. Package materials are transferred to a heating section after sterilization. Web film is crimped by heating plate moving vertically in a heating section, and transferred to a forming section after heating enough. A plug-assisted compressed air forming system preliminarily forms the film by nearly 80% by plug, and completely forms the film by die while cooling with sterile air blowing. The formed film is transferred to a filling section. Particular consideration on the safety of aseptic packages is essential. 3 refs., 10 figs.

  11. Present state of desertification and soil conservation in Niger; Niger ni okeru sabakuka to dojo hozen no torikumi

    Energy Technology Data Exchange (ETDEWEB)

    Nagano, T. [Kyoto Univ. (Japan)

    1998-08-01

    Major factors for desertification are soil deterioration phenomena such as decrease in the covering by plants, water erosion, weathering, and decrease of organic matter. The current state of desertification and the trend of soil conservation are introduced quoting the case of Niger, and the current state of facing the problem on the spot is introduced lastly. Increase of the population and tight situation of the utilization of land in such severe environment as unstable rainfalls and poor soil are the causes for the poor production basis. Another cause is farming of the extensive style even at present. Effective measures for soil conservation are the improvement of productivity and conservation by water harvesting and fertility management. However, self-help soil conservation by the inhabitants themselves is currently difficult because of the present state of the social economy. It is required that soil conservation is positioned in the overall development of farming village and is developed simultaneously with the improvement of the rate of self-supporting, securing of cash income, and improvement of living environment. 10 refs., 9 figs., 3 tabs.

  12. Case studies on construction works of short span bridges in Kenya; Kenya kyowakoku ni okeru chusho kyoryo koji no jirei

    Energy Technology Data Exchange (ETDEWEB)

    Kurino, S. [Honshu-Shikoku Bridge Authority, Tokyo (Japan)

    1998-01-01

    In the Republic of Kenya, problems are how to build bridges over small rivers, not big rivers, and what bridge types to choose for reduction in cost. Concrete bridges under the direct control of the Government construction office are 15m at the longest, and they are directly founded on the hard basement after a little excavation. In formulating construction plans, it is necessary to take climate into account, such that there is but a small amount of precipitation and that it concentrates in the rainy season. The first stage of bridge building involves the construction of low-cost structures which enable river-crossing except in the rainy season. This first-stage concept is worth deliberation when it is known that there are semiarid regions where river-crossing is prohibited due to high water levels in the rainy season but for approximately two weeks a year. In the second stage, permanent structures are required, serviceable even in the high water level season. In the third stage, it is necessary to construct bridges conforming to the road assuring excellent trafficability. For reduction in the cost of small bridge construction, drift types, culvert types, and temporary bridges like Bailey bridges are important choices. 2 refs., 12 figs.

  13. Magnetic susceptibility measurements in Yellowstone National Park, USA; Beikoku Yellowstone kokuritsu koen ni okeru genchi jikaritsu sokutei

    Energy Technology Data Exchange (ETDEWEB)

    Okuma, S. [Geological Survey of Japan, Tsukuba (Japan)

    1997-05-27

    For the purpose of interpreting data of the aeromagnetic anomalies in Yellowstone National Park in the U.S.A., in-situ magnetization intensity measurements have been carried out in 1994 and 1995 on geological outcrops of rocks in that area. Comparisons and discussions were given on the measurement results, and existing rock magnetic data and aeromagnetic anomaly data available for the area. Outside the Yellowstone caldera, part of granitic gneisses among the Precambrian granitic gneisses and crystalline schists distributed to the north has an abnormally high magnetization intensity of 1 {times} 10 {sup -2} SI. This could be a powerful anomaly source for the high magnetic anomaly in this area. Paleogene volcanic rocks distributed widely in the eastern part of the park also have magnetization intensity as high as 1 {times} 10 {sup -2} SI or higher, which are also thought a powerful anomaly source in this area. Part of Pleistocene basalts which are exposed partially in the western part of the park has also very high magnetization intensity at 1 {times} 10 {sup -2} SI or higher. This suggests correlation with the magnetic anomaly in the east-west direction distributed in this area. Quaternary rhyolites are more magnetic than Quaternary welded tuffs, which should give greater effects to the magnetic anomaly. 10 refs., 5 figs.

  14. Prediction of discharge change in a cold region river; Kanchi kasen ni okeru toki kassui koki no ryuryo hendo yosoku

    Energy Technology Data Exchange (ETDEWEB)

    Yamazaki, M.; Koyama, S. [Hokkaido Electric Power Co. Inc., Sapporo (Japan); Hasegawa, K. [Hokkaido University, Sapporo (Japan). Faculty of Engineering; Hirayama, K. [Iwate University, Iwate (Japan). Faculty of Engineering

    1997-05-15

    Daily discharge change during the winter period in a cold region river used for hydroelectric power station has been investigated through discussion of formation mechanism and prediction model simulation. As a result of the observation in winter, it was found that the change of river flow with partially melted solid ice cover in early March increased when the average temperature at night between 18 pm and 7 am was less than -4 to -6 degC showing the negative value of radiation balance. Daily decrease and increase in the river flow during freezing period were observed due to the formation of ice dam at the rapid change part of river gradient. Especially in early March when completely frozen ice was partially melted, anchor ice was developed in the river by frazil, and formation of step-pools was often observed in the field. Results of flow prediction simulation using a step-pool model considering development and regression of anchor ice agreed well with those from the actual measurements. 9 figs., 1 tab.

  15. Transition of wind power utilization technology in the 20th century; 20 seiki ni okeru furyoku riyo gijutsu no hensen

    Energy Technology Data Exchange (ETDEWEB)

    Ushiyama, I. [Ashikaga Inst. of Tech., Tochigi (Japan)

    2000-04-01

    Windmills are one of the oldest prime movers and have been used for more than 700 years in Europe. The transition from low speed windmills for grain grinding and water pumping to high speed wind turbines for electric power generation had occurred at the end of 19{sup th} century. This paper, at first, reviews the windmill technologies and the researchers before 20th century. Then describes the back ground of how the wind power generator has existed and how the four pioneers developed their wind power generator. The historical developments of windmills to wind turbines in this century are studied focusing mainly on Danish activities. Then, the effort of the development of large wind turbine such as Smith-Putnum's first MW machine in U.S.A. and other mammoth machine concept are introduced. The new concept machines such as Savonius and Darrieus wind turbines in 1920s to 1930s are also explained. Finally, the novel technologies of wind turbine covering larger machines, variable speed generators, special wing sections for wind turbines, theoretical analysis method of wind turbine performance, offshore wind turbines, and wind turbine control technologies are stated. (author)

  16. Noise and vibration reduction technology in hybrid vehicle development; Hybrid sha kaihatsu ni okeru shindo soon teigen gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Yoshioa, T.; Sugita, H. [Toyota Motor Corp., Aichi (Japan)

    2000-03-01

    Accomplishing both environmental protection and good NVH performance has become a significant task in automotive development The first-in-the-world hybrid passenger car of mass production. 'Prius', has achieved superior NV performance compared with conventional vehicles with a 1.5-liter engine along with 50% reduction of fuel consumption and CO{sub 2} emissions. low HC, CO and NO{sub x} emissions. This paper describes NV reduction technology for solving problems peculiar to the hybrid vehicle such as engine start/stop vibration, drone noise at low engine speed and motor/generator noise and vibration. It also mentions application technology of low rolling resistance tires with light weight wheels and recycled material for sound proofing. (author)

  17. Pseudo-random data acquisition geometry in 3D seismic survey; Sanjigen jishin tansa ni okeru giji random data shutoku reiauto ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Minegishi, M.; Tsuburaya, Y. [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1996-10-01

    Influence of pseudo-random geometry on the imaging for 3D seismic exploration data acquisition has been investigate using a simple model by comparing with the regular geometry. When constituting wave front by the interference of elemental waves, pseudo-random geometry data did not always provide good results. In the case of a point diffractor, the imaging operation, where the constituted wave front was returned to the point diffractor by the interference of elemental waves for the spatial alias records, did not always give clear images. In the case of multi point diffractor, good images were obtained with less noise generation in spite of alias records. There are a lot of diffractors in the actual geological structures, which corresponds to the case of multi point diffractors. Finally, better images could be obtained by inputting records acquired using the pseudo-random geometry rather than by inputting spatial alias records acquired using the regular geometry. 7 refs., 6 figs.

  18. Coal liquefaction in early stage of NEDOL process 1t/d PSU; 1t/d PSU ni okeru ekika shoki hanno ni kansuru kento

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, K.; Kawabata, M.; Mochizuki, M.; Imada, K. [Nippon Steel Corp., Tokyo (Japan); Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan)

    1996-10-28

    To investigate the behavior of coal liquefaction reaction in early stage as a part of studies on the coal liquefaction characteristics using NEDOL process 1 t/d process supporting unit (PSU), coal slurry sample was taken from the outlet of slurry preheater located in the upflow of liquefaction reactors, and was tested. Tanito Harum coal was used for liquefaction. Preheater was operated under the condition of pressure of 170 kg/cm{sup 2}, gas flow rate of 64 Nm{sup 3}/hr, and at temperature up to 410{degree}C at the outlet, in response to the standard test condition. The slurry sample was discharged into a high temperature separator with temperature of 250{degree}C. Liquefaction was not proceeded at the outlet of preheater. Solid residue yielded around 80%, and liquid yielded around 15%. Gases, CO and CO2, and water yielded also small amount around 3%. The solid sample contained much IOM fraction (tetrahydrofuran-insoluble and ash), and the liquid contained much heavy oil fraction. Hydrogenation was not proceeded, and the hydrogen consumption was very low showing below one-tenth of that at the usual operation. Hydrogen sulfide gas was formed at early stage, which suggested that the change of iron sulfide catalyst occur at early stage of liquefaction. 1 ref., 5 figs., 2 tabs.

  19. Investigation of the deposit formation in pipelines connecting liquefaction reactors; 1t/d PSU ni okeru ekika hanno tokan fuchakubutsu no seisei yoin ni kansuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Okada, Y.; Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan); Mochizuki, M.; Imada, K. [Nippon Steel Corp., Tokyo (Japan)

    1996-10-28

    The liquefaction reaction system of an NEDOL process coal liquefaction 1t/d PSU was opened and checked to investigate the cause of the rise of differential pressure between liquefaction reactors of the PSU. The liquefaction test at a coal concentration of 50 wt% using Tanito Harum coal was conducted, and it was found that the differential pressure between reactors was on the increase. By the two-phase flow pressure loss method, deposition thickness of deposit in pipelines was estimated at 4.4mm at the time of end operation, which agreed with a measuring value obtained from a {gamma} ray. The rise of differential pressure was caused by deposit formation in pipelines connecting reactors. The main component of the deposit is calcite (CaCO3 60-70%) and is the same as the usual one. It is also the same type as the deposit on the reactor wall. Ca in coal ash is concerned with this. To withdraw solid matters deposited in the reactor, there are installed pipelines for the withdrawal at the reactor bottom. The solid matters are regularly purged by reverse gas for prevention of clogging. As the frequency of purge increases, the deposit at the reactor bottom decreases, but the deposit attaches strongly to pipelines connecting reactors. It is presumed that this deposit is what Ca to be discharged out of the system as a form of deposition solid matter naturally in the Ca balance precipitated as calcite in the pipeline connecting the reactor. 3 refs., 5 figs., 4 tabs.

  20. Analysis of the pressure response of high angle multiple (HAM) fractures intersecting a welbore; Kokeisha multi fracture (HAM) kosei ni okeru atsuryoku oto kaiseki ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Ujo, S.; Osato, K. [Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Arihara, N. [Waseda University, Tokyo (Japan); Schroeder, R.

    1996-05-01

    This paper reports pressure response analysis on wells piercing a high angle multi (HAM) fracture model. In this model which is defined on a three-dimensional space, a plurality of slanted fractures intersect with wells at high angles (however, intersection of fractures with each other is not considered). With respect to the pressure response analysis method using this model, the paper presents a basic differential equation on pressure drawdown and boundary conditions in the wells taking flows in the fractures pseudo-linear, as well as external boundary conditions in calculation regions (a reservoir spreads to an infinite distance, and its top and bottom are closed by non-water permeating beds). The paper also indicates that results of calculating a single vertical fracture model and a slanted fracture model by using a numerical computation program (MULFRAC) based on the above equations agree well respectively with the existing calculation results (calculations performed by Erlougher and Cinco et al). 5 refs., 6 figs.

  1. On the muscle activity control in the hierarchy motor systems. Hierarchy undo system ni okeru kin no kassei seigyo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Akiba, M.; Miyamoto, Y. (Osaka Industrial University, Osaka (Japan). Faculty of Engineering)

    1991-10-31

    Excitory impulses for motor systems are controlled by the psychophysiological nervous systems in the body either autonomically or voluntarily. Involved in the voluntary control loop are motor cortex, basal gangalia, thalamus, cerebellum, etc. The purpose of this study is to confirm whether it is possible to reduce or emphasize the muscle contraction voluntarily through electromyogram (EMG) feedback training. EMG can indicate the excitory impulses of motor units. In the experiments, electrodes were placed on the skin above muscles. A significant reduction effect was observed for subjects trained in relaxation of the forehead musculature through EMG feedback. Results of the experiments suggested that biofeedback training for relaxation of the forehead tensional muscle might be effective in eliminating muscle contraction, and that feedback training for activation of damaged muscles might be effective in emphasizing muscle contraction. 4 refs., 9 figs.

  2. Drilling of geothermal well in Onikobe geothermal field and developping Oguni geothermal field. Onikobe oyobi Oguni chiiki ni okeru chinetsusei kussaku ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Abe, S.; Kurishima, S. (Electric Power Development Co. Ltd., Tokyo (Japan)); Mezaki, Y.

    1992-03-25

    This paper describes the Onikobe Geothermal Power Plant in Miyagi Prefecture developed by the Electric Power Source Development Co., Ltd., and the current development state of drilling geothermal wells at the Oguni geothermal field in Kumamoto Prefecture. The Onikobe area has alteration zone distributed widely, with a clayey layer at a depth between 80 m and 150 m, and steam reservoir layers at depths around 300 m and deeper than 800 m. The production wells in shallow layers were drilled with great attentions because the layer down to about 300 m, which is a steam layer, has an extremely high underground temperature rise rate and incessant danger of spontaneous explosions. Drilling deep slanted wells used an increased number of casing pipes. The slanted drilling has dealt with the high temperatures starting at shallow depths by beginning the hole bending at a depth as unexceptionally shallow as 80 meters. The Oguni area presented no special problems in geothermal well drilling. However, because of employing a base system in which excavation locations are limited as a result of highly undulated topography and road conditions, almost all wells were drilled slanted. 21 refs., 8 figs., 13 tabs.

  3. Survey of the trend of technical development and industrial policies in Asian countries; Asia shokoku ni okeru gijutsu kaihatsu no doko to sangyo gijutsu seisaku ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A sharp rise in industrial productivity in Asia countries indicates a rising level of R and D technology. Since Japan has not clearly grasped the R and D ability in these countries, it has not given appropriate personnel/material R and D support to them. Therefore, for the purpose of exactly grasping the R and D ability of Asian countries (Korea, Taiwan, the Philippines, Indonesia and India) and studying an effective and appropriate method for R and D cooperation, a survey was conducted of R and D potentials in Asia and R and D support policies of the countries. As a result of the survey, the following are taken up as items to be considered: promotion of exchanges between Tsukuba, etc. in Japan and research/university towns and science parks being constructed in lots of countries, participation of private companies in high-tech joint work in cooperation with Japan, sending information from Japan using internet, etc. and exact grasp of needs at partner side, cooperation given to new comers without asking for research results (use of OB researchers, etc.) 25 refs., 39 figs., 59 tabs.

  4. Questionnaire investigation for the earthquake in Honjo city and Yazawa city, Akita Prefecture; Jishin ni kansuru ishiki chosa (Akitaken Honjoshi oyobi Yuzawashi ni okeru anketo kara)

    Energy Technology Data Exchange (ETDEWEB)

    Nogoshi, M. [Akita University, Akita (Japan). College of Education; Kabutoya, S.

    1996-05-01

    Consciousness for the earthquake was investigated by questionnaire surveys made in Honjo City and Yuzawa City, Akita Pref. in October 1995 twelve years after the Nihonkai Chubu Earthquake (M=7.7) in May 1983. The survey was conducted in terms of 27 items including personality, memory, knowledge/interest, psychology/action, mental attitude/preparations, wishes for researchers and administration, etc. Also included were the items on the Great Hanshin-Awaji Earthquake and the earthquake blank areas. The number of distributed questionnaires and the recovery rate of them are 1500 and 79.2% in Honjo City, and 1700 and 84.7% in Yuzawa City. From the survey, it was found that people have a lot of knowledge of and high interest in the earthquake and well remember it, and a lot of people know of tsunami, liquefaction phenomena, and the earthquake blank area. Further, they are afraid of earthquakes and think of their actions to be taken in case of earthquake. However, most people are little prepared for earthquakes. Important future subjects were suggested for the study of disaster prevention measures. 13 figs.

  5. Results of photovoltaic power generation system operation in Tokyo Electric Power Company; Tokyo Denryoku ni okeru taiyoko hatsuden setsubi no unten jisseki ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Fukuda, H.; Itokawa, K. [Tokyo Electric Power Co. Inc., Tokyo (Japan)

    1996-10-27

    A report was made on the measurement of data and the results of the analysis at 14 sites of photovoltaic power generation facilities operated under system interconnection by Tokyo Electric Power Company. This type of system is provided in 40 sites as of the end of fiscal 1995, generating 479kw. The items measured were the generated electric energy at all 14 sites, and the quantity of solar radiation, outside air temperature, panel temperature, etc., at limited sites; and the capacity of each equipment, azimuth and inclination of the panel were also recorded simultaneously. Hourly values were used for the analysis. Five minute values were utilized, however, in the examination of the cause of lowered output and in the situation recognition of the influence of the shade or the change of weather. The utilization factor of the facilities was in the average 10.8% in fiscal 1994 and 10.7% in fiscal 1995. The factor decreased slightly unless the panel azimuth faced due south. The utilization factor at the panel inclination of 35 degrees and 45 degrees showed both 10.4% through the year making no difference. The system seemed to show no overwhelming possibilities in coping with electric power demand. The reason was that deviation existed for 2 hours or so in the peak and that reliability was low as basic power facilities. However, it was determined that the system be continuously examined in future. 9 figs., 1 tab.

  6. Disinfectants used in medal field and problems caused from their use. Igaku ryoiki ni okeru sakkinzai to sorera shiyo ni yoru mondaiten

    Energy Technology Data Exchange (ETDEWEB)

    Okuda, K.; Watabe, S. (Yokohama City University, Yokohama (Japan). School of Medicine)

    1994-04-05

    This paper describes typical anti-microorganism chemicals used in hospitals, and touches on measures against intra-hospital infection. Killing microorganisms reliably by using a high-pressure steam sterilization method is the best means for medical devices and apparatuses. However, there are high-priced medical devices that cannot withstand such a method and require other processes according to the situations, such as gas sterilization and alcohol disinfection. In addition to such sterilization methods as using heat, alcohols, and gases, methods that have been developed recently may include the following: use of Bronopol (an antiseptic) and anti-mold agents that have electronphilic functional groups, disinfectants using metal ions from silver, zinc and copper, and other materials. The problem of intra-hospital infection is caused typically by MRSA, hepatitis virus and Pseudomonas aeruginosa. Preventive measures require good knowledge about their infection courses and disinfecting technologies, as well as an attention not to cause change in the ecology as a result of using excessively strong chemicals. 18 refs., 1 fig., 1 tab.

  7. Study on the effect of measurement points upon reduced added mass matrix; Shukusho fuka shitsuryo matrix ni okeru kansokuten no eikyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Funaki, T.; Hayashi, S. [Osaka University, Osaka (Japan). Faculty of engineering

    1996-12-31

    It is known in estimating vibration characteristics of a ship that fluid range affects largely a structure. A parameter calculation was performed on node vibration in the vertical direction of a rotating elliptic body such as a ship to investigate the effect of an arranging method of the measurement points upon the result of the analysis. As a result, it is thought that equivalent interval arrangement of 21 measurement points would be sufficient in a lower order side mode of vibrations with less than four nodes. An analysis of calculations performed by arranging measurement points in experimental measurement points revealed that analysis accuracy would not increase even if the number of measurement points is increased if it is done so without considering rotation vector. An experiment was carried out with the number of measurement points increased to verify the above fact, with which the analysis was verified correct. Therefore, as has been forecasted in the previous report, the cause for the analysis accuracy deterioration in a high order mode may be estimated as the effect of the rotation vector. However, since it is not the situation that an analysis considering the rotation vector has been conducted, it cannot be concluded yet that the effect of the rotation vector is the sole cause. 4 refs., 14 figs., 7 tabs.

  8. Study of the influence of microgravity on the biological cells and molecular level; Seitai saibo bunshi level ni okeru bisho juryoku no eikyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The shape of osteoblast, gene appearance, gene of rice blast, cellular fusion of plants, gravity acceptance mechanism of unicellular organisms, and physiological and immunity functions of mice were investigated under the microgravity condition. The influence of gravity on the vital reaction and the influence of microgravity on the crystallization of vital substances were also investigated. For the observation of osteoblast, the fluorescence dye reacted with Ca was well taken in the cells. The microgravity affected the stability of rice blast, but hardly affected the protoplast culture of mushroom. The reaction of ciliate against the gravity related to the specific gravity difference between cells and outer liquid. The level of adrenaline in blood of mice increased during the drop. The moving speed of trigger waves of chemical parallel slit formed at the BZ reaction under the microgravity became 60% to 80% of that on the ground. In the case of crystallization at the deposition agent concentration of 1% to 4%, the turbidity showing the degree of crystallization changed complicatedly. Nine processes of crystal growth were recognized. 21 refs., 55 figs., 1 tab.

  9. Population dynamics of bacteria for phosphorus removal in sequencing batch reactor (SBR) activated sludge processes. Kaibunshiki kassei odeiho ni okeru datsu rin tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Okada, M.; Ueno, Y.; Lin, C.; Murakami, A. (Tokyo University of Agriculture and Technology, Tokyo (Japan))

    1990-01-10

    As the phosphorus removal processes, chemical methods and biological methods are considered. This paper discussed a biological phosphorus removal method. Laboratory experiments of phosphorus removal in sequencing batch reactor (SBR) activated sludge processes were operated using synthetic waste water to clarify the effects of solid retention time (SRT) and organic substrates on the accumulation of bacteria having phosphorus removal ability (bio-P-bacteria). The accumulation of bio-P-bacteria was enhanced by large fluctuation in concentration of organic substances in the reactor fed in a short period of time under anaerobic condition. However, the accumulation did not be enhanced in the reactor operated with SRT less than 25 d. The specific growth rates of bio-P-bacteria were estimated to a range from 0.033/d to 0.035/d in the SBR activated sludge processes fed with glucose and polypeptone as substrates. Therefore, large SRT is necessary for the accumulation of bio-P-bacteria. 18 refs., 10 figs., 1 tab.

  10. Change in surface SP caused by pressure buildup observed at the Nigorikawa geothermal area; Nigorikawa chiiki ni okeru atsuryoku buildup ji no shizen den`i henka

    Energy Technology Data Exchange (ETDEWEB)

    Yasukawa, K.; Yano, Y.; Matsushima, N.; Ishido, T. [Geological Survey of Japan, Tsukuba (Japan); Takahashi, M.; Suzuki, I.; Aoyama, K.; Kuwano, T.

    1996-10-01

    To examine the effect of change of subsurface flow system on the surface SP (self potential), SP measurements were carried out before and after the pressure buildup and drawdown during the periodic inspection at Nigorikawa area. Relation between the SP distribution and the observed data was also examined by 2-D numerical simulation. Tendency was found that the SP increased gradually with the production near the production well, decreased during the pressure buildup, and increased again during the drawdown. There were some points having the reverse tendency in the surrounding area. Behavior during the pressure buildup and drawdown was not clear. The resistivity near the ground surface was low ranging between 2 and 5 ohm/m within the Nigorikawa basin. The variation of SP was not so large when compared with the measuring error. The SP profiles on the secondary section passing in the center of caldera at the production stop and at one week after the production start were well corresponded with the profiles under natural conditions which were reproduces using the 2-D model. It was considered that the SP profile before the production stop was affected by the production. 12 refs., 6 figs., 1 tab.

  11. Comparison of {gamma}-ray profile across active normal and reverse faults; Seidansogata to gyakudansogata katsudanso ni okeru hoshano tansa kekka no hikaku

    Energy Technology Data Exchange (ETDEWEB)

    Iwata, A.; Wada, N.; Sumi, H. [Shimada Technical Consultants, Ltd., Shimane (Japan); Yamauchi, S.; Iga, T. [Shimane Univ., Shimane (Japan)

    1996-10-01

    Active faults confirmed at trench and outcrop were surveyed by the {gamma}-ray spectrometry. The active fault found at trench is a normal fault, and that found at outcrop is a reverse fault. The {gamma}-ray spectral characteristics of these two types of faults were compared to each other. The normal fault is named as Asagane fault located in Aimi-machi, Saihaku-gun, Tottori prefecture. The reverse fault is named as Yokota reverse fault located in Yokota-cho, Nita-gun, Shimane prefecture. Rises of radon gas indicating the existence of opening cracks were confirmed above the fault for the normal fault, and at the side of thrust block for the reverse fault. It was considered that such characteristics were caused by the difference of fault formation in the tensile stress field and in the compressive stress field. It was also reconfirmed that much more information as to faults can be obtained by the combined exploration method using the total counting method and the spectral method. 14 refs., 7 figs.

  12. High-resolution aeromagnetic survey in the area of Arima-Takatsuki-Rokko active fault system; Arima Takatsuki Rokko katsudanso chiiki ni okeru komitsudo kuchu jiki tansa

    Energy Technology Data Exchange (ETDEWEB)

    Nakatsuka, T.; Okuma, S.; Morijiri, R.; Makino, M. [Geological Survey of Japan, Tsukuba (Japan)

    1996-10-01

    High-resolution aeromagnetic survey was conducted in December, 1995, over the area of Arima-Takatsuki-Rokko active fault system, where the 1995 Hyogo-South (Kobe) earthquake took place. Based on the surveyed data, the magnetic anomaly distribution in the Kei-Hanshin district was illustrated. Features of magnetic anomaly observed in it were discussed. Influence of artificial structures in the coastal zone of Kobe City was tried to be removed. Distinct magnetic anomaly observed in the center of Kyoto City was located at the southern part near Shijo-Karasuma. This was mainly affected by the artificial structure. A high magnetic anomaly with a long wave length was observed in the southern part of Kyoto. There was a high magnetic anomaly in an area surrounded by central cities of Nishinomiya-Toyonaka district. At the location where positive and negative magnetic anomalies were illustrated in NEDO`s map in the coastal zone of Kobe City, the anomaly pattern was clarified. The influence of artificial structure was approximated using a point dipole. The dipole was placed in each block having a magnetic anomaly. The parameter was determined by the inverse analysis, to remove the influence. Consequently, most of magnetic anomalies due to artificial structures could be removed. 6 figs.

  13. Boilling nucleation on very small film heater subjected to extremely rapid heating. Gokubisho heimen dennetsumen no cho kosoku kanetsuji ni okeru futto kaku seisei

    Energy Technology Data Exchange (ETDEWEB)

    Iida, Y.; Okuyama, K. (Yokohama National Univ. (Japan). Faculty of Engineering); Sakurai, K. (NEC Corp., Tokyo (Japan))

    1994-04-25

    A very small film heater is heated with high rate of temperature rise by carrying current in liquids, and a high heating rate of 93[times]10[sup 6]K/s is realized as the average heating rate for achieving the nucleation temperature from the liquid temperature. Based on this result, experimental study is made on the boiling nucleation of ethyl alcohol, toluene, and water under atmospheric pressure to investigate the fluctuation nucleation phenomenon. The nucleation temperature gradually increases with the increase in the heating rate, and becomes a constant saturated value in the range higher than a certain heating rate. Based on the fluctuation nucleation theory, the effects of heater surface temperature, elapsed time, and the contact angle of the liquid and heater surface on the nucleation density are obtained and compared with the result of the experiment. The number density of the nucleated bubbles is measured and studied in relation to the heating rate. The phenomenon observed at a comparatively high rate of heating, particularly the one producing caviar-like bubbles, is concluded to be due mainly to fluctuation nucleation. 15 refs., 15 figs.

  14. Conversion of char nitrogen to N2 under incomplete combustion conditions; Fukanzen nensho jokenka ni okeru char chuchisso no N2 eno tenka

    Energy Technology Data Exchange (ETDEWEB)

    Zhuang, Q.; Yamauchi, A.; Oshima, Y.; Wu, Z.; Otsuka, Y. [Tohoku University, Sendai (Japan). Institute for Chemical Reaction Science

    1996-10-28

    The effect of combustion conditions on conversion of char nitrogen to N2 was studied in the combustion experiment of char obtained by pyrolysis of coal. Char specimen was prepared by holding ZN coal of Chinese lignite in Ar atmosphere at 1123K for one hour. A batch scale quartz-made fluidized bed reactor was used for combustion experiment. After the specimen was fluidized in reaction gas, it was rapidly heated to start combustion reaction. CO, CO2 and N2 in produced gases were online measured by gas chromatography (GC). As the experimental result, under the incomplete combustion condition where a large amount of CO was produced by consuming almost all of O2, no NOx and N2O produced from char were found, and almost all of N-containing gas was N2. At the final stage of combustion, pyridinic-N disappeared completely, and pyrrolic-N decreased, while O-containing nitrogen complexes became a main component. It was thus suggested that O-containing nitrogen complexes are playing the role of intermediate product in combustion reaction. 7 refs., 4 figs., 1 tab.

  15. Coal conversion rate in 1t/d PSU liquefaction reactor; 1t/d PSU ekika hannoto ni okeru sekitan tenka sokudo no kento

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, K.; Imada, K. [Nippon Steel Corp., Tokyo (Japan); Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan)

    1996-10-28

    To investigate the coal liquefaction characteristics, coal slurry samples were taken from the outlets of the reactors and slurry preheater of NEDOL process 1 t/d process supporting unit (PSU), and were analyzed. Tanito Harum coal was used for liquefaction, and the slurry was prepared with recycle solvent. Liquefaction was performed using synthetic iron sulfide catalyst at reaction temperatures, 450 and 465{degree}C. Solubility of various solid samples was examined against n-hexane, toluene, and tetrahydrofuran (THF). When considering the decrease of IMO (THF-insoluble and ash) as a characteristic of coal conversion reaction, around 20% at the outlet of the slurry preheater, around 70% within the first reactor, and several percents within the successive second and third reactors were converted against supplied coal. Increase of reaction temperature led to the increase of evaporation of oil fraction, which resulted in the decrease of actual slurry flow rate and in the increase of residence time. Thus, the conversion of coal was accelerated by the synergetic effect of temperature and time. Reaction rate constant of the coal liquefaction was around 2{times}10{sup -1} [min{sup -1}], which increased slightly with increasing the reaction temperature from 450 to 465{degree}C. 3 refs., 5 figs., 1 tab.

  16. Effect of total pressure on sulfur capture of Ca-ion exchanged coal; Kaatsu jokenka ni okeru Ca-tanjitan no datsuryu koka

    Energy Technology Data Exchange (ETDEWEB)

    Lin, S.; Benjamin, G.; Abe, H.; Harano, A.; Takarada, T. [Gunma University, Gunma (Japan). Faculty of Engineering

    1996-10-28

    In relation to coal gasification and combustion under high pressure as highly efficient coal utilization, the effect of total pressure and sintering on the SO2 capture ability of Ca-ion exchanged coal and other desulfurizing agents were studied. In experiment, specimens were filled into a small pressurized reactor to heat them under high-pressure N2 atmosphere. After the completion of combustion reaction of char at 850{degree}C, SO2, CO2 and CO gases were measured at an outlet while flowing SO2/N2. As the experimental result, all of the S content in Ca-ion exchanged coal was not absorbed by Ca content in coal during pyrolysis and combustion, resulting in discharge of 36% of the S content. Since Ca-ion exchanged coal is fast in combustion reaction, most of the S content was desulfurized by coal ash. The ash content yielded from Ca-ion exchanged coal was more excellent in SO2 capture ability than limestone even under higher pressure. In the case of CO2 partial pressure lower than equilibrium CO2 pressure for CaCO3 decomposition, the capture ability decreased with an increase in total pressure, while in higher CO2 partial pressure, it was improved. 1 ref., 7 figs., 2 tabs.

  17. Formation of N2 in the fixed-bed pyrolysis of low rank coals and the mechanisms; Koteisho netsubunkai ni okeru teitankatan kara no N2 no sisei

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Z.; Otsuka, Y. [Tohoku University, Sendai (Japan). Institute for Chemical Reaction Science

    1996-10-28

    In order to establish coal NOx preventive measures, discussions were given on formation of N2 in the fixed-bed pyrolysis of low rank coals and the mechanisms thereof. Chinese ZN coal and German RB coal were used for the discussions. Both coals do not produce N2 at 600{degree}C, and the main product is volatile nitrogen. Conversion into N2 does not depend on heating rates, but increases linearly with increasing temperature, and reaches 65% to 70% at 1200{degree}C. In contrast, char nitrogen decreases linearly with the temperature. More specifically, these phenomena suggest that the char nitrogen or its precursor is the major supply source of N2. When mineral substances are removed by using hydrochloric acid, their catalytic action is lost, and conversion into N2 decreases remarkably. Iron existing in ion-exchanged condition in low-rank coal is reduced and finely diffused into metallic iron particles. The particles react with heterocyclic nitrogen compounds and turn into iron nitride. A solid phase reaction mechanism may be conceived, in which N2 is produced due to decomposition of the iron nitride. 5 refs., 4 figs., 1 tab.

  18. Change in surface characteristics of coal in upgrading of low-rank coals; Teihin`itan kaishitsu process ni okeru sekitan hyomen seijo no henka

    Energy Technology Data Exchange (ETDEWEB)

    Oki, A.; Xie, X.; Nakajima, T.; Maeda, S. [Kagoshima University, Kagoshima (Japan). Faculty of Engineering

    1996-10-28

    With an objective to learn mechanisms in low-rank coal reformation processes, change of properties on coal surface was discussed. Difficulty in handling low-rank coal is attributed to large intrinsic water content. Since it contains highly volatile components, it has a danger of spontaneous ignition. The hot water drying (HWD) method was used for reformation. Coal which has been dry-pulverized to a grain size of 1 mm or smaller was mixed with water to make slurry, heated in an autoclave, cooled, filtered, and dried in vacuum. The HWD applied to Loy Yang and Yallourn coals resulted in rapid rise in pressure starting from about 250{degree}C. Water content (ANA value) absorbed into the coal has decreased largely, with the surface made hydrophobic effectively due to high temperature and pressure. Hydroxyl group and carbonyl group contents in the coal have decreased largely with rising reformation treatment temperature (according to FT-IR measurement). Specific surface area of the original coal of the Loy Yang coal was 138 m{sup 2}/g, while it has decreased largely to 73 m{sup 2}/g when the reformation temperature was raised to 350{degree}C. This is because of volatile components dissolving from the coal as tar and blocking the surface pores. 2 refs., 4 figs.

  19. Effect of sulfur or hydrogen sulfide on initial stage of coal liquefaction in tetralin; Sekitan ekika shoki katei ni okeru io to ryuka suiso no hatasu yakuwari

    Energy Technology Data Exchange (ETDEWEB)

    Nakada, M. [Government Industrial Research Institute, Kyushu, Saga (Japan)

    1996-10-28

    It is well known that the solubilization of coal can be accelerated by adding sulfur or hydrogen sulfide during direct liquefaction of difficult coals. From the studies of authors on the coal liquefaction under the conditions at rather low temperatures between 300 and 400{degree}C, liquefaction products with high quality can be obtained by suppressing the aromatization of naphthene rings, but it was a problem that the reaction rate is slow. For improving this point, results obtained by changing solvents have been reported. In this study, to accelerate the liquefaction reaction, Illinois No.6 coal was liquefied in tetralin at temperature range from 300 to 400{degree}C by adding a given amount of sulfur or hydrogen sulfide at the initial stage of liquefaction. The addition of sulfur or hydrogen sulfide provided an acceleration effect of liquefaction reaction at temperature range between 300 and 400{degree}C. The addition of sulfur or hydrogen sulfide at 400{degree}C increased the oil products. At 370 and 400{degree}C, the liquid yield by adding sulfur was slightly higher than that by adding hydrogen sulfide, unexpectedly. The effects of sulfur and hydrogen sulfide were reversed when increasing the hydrogen pressure. 5 figs., 1 tab.

  20. Ignition and combustion of solid-particle mixed fuel drop in a microgravity environment; Bisho juryokuka ni okeru kotai ryushi konnyu nenryo ekiteki no chakka to nensho

    Energy Technology Data Exchange (ETDEWEB)

    Tanishige, R. [Zexel Corp., Tokyo (Japan); Shimoguchi, T. [Mitsubishi Agricultural Machinery Co. Ltd., Tokyo (Japan); Yoshizaki, T. [Hiroshima University, Hiroshima (Japan); Hiroyasu, H. [Kinki University, Osaka (Japan); Sakuraya, T. [Japan Space Utilization Promotion Center, Tokyo (Japan)

    1998-10-20

    The ignition and combustion behavior of single Mg slurry and pure C slurry fuel drops were observed at higher temperature under microgravity condition, and compared with those under normal gravity condition. As a result, the lowest ignition temperature of primary flame in liquid fuel combustion under microgravity is lower than that under normal gravity. Solid combustion (secondary combustion) characteristics of slurry fuel drops under microgravity are unaffected by the kind of liquid fuels, however, primary flame ignition delay of slurry fuel drops using cetane is larger than that using dodecane. Under microgravity, soot particle layers are observed on flame surfaces after expansion and contraction of spherical flame during a primary flame period. The layer density is larger in pure C slurry than another slurry. In particular, a primary flame expansion ratio of pure C slurry fuel drops increases stepwise with ambient temperature in a temperature range over the lowest ignition temperature of solid combustion. 8 refs., 18 figs., 3 tabs.

  1. Ignition and combustion of a coal-oil mixture drop in a microgravity environment; Bisho juryokuka ni okeru COM nenryo ekiteki no chakka to nensho

    Energy Technology Data Exchange (ETDEWEB)

    Tanishige, R.; Yoshizaki, T.; Hiroyasu, H. [Hiroshima University, Hiroshima (Japan); Sakuraya, T. [Japan Space Utilization Promotion Center, Tokyo (Japan)

    1996-12-20

    Slurry drops made of coal-oil mixture (COM) were ignited and burned at the underground gravity-free experiment center to investigate their characteristics. The experiment was purposed to analyze vapor combustion in a location removed of influence from natural convection and forced convection, and compare it with combustion behavior under normal gravity. The following findings were obtained: the primary flame swells and contracts after ignition, swells again making the flame diameter maximum, and then contracts again to form a second-stage fuel flame; ignition delays when ambient temperature is low, and the second-stage flame occurs in a high temperature region; the primary flame under micro gravity is generated in a lower temperature zone than that under the normal gravity, and the primary flame period is extended longer; COM drop ignition under micro gravity requires smaller activation energy; generation of soot husks centering around the drops becomes remarkable as brightness of spherical flame decreases; the ignition started at 589 K against 970 K for ignition under the normal gravity; liquid components evaporated before ignition are distributed spherically symmetrically around drops; and there is no air flow to have the components scattered and lost. 12 refs., 8 figs., 2 tabs.

  2. Survey of the actual state of the coal related research and development in Japan. 11; Nippon ni okeru sekitan kanren kenkyu kaihatsu jittai chosa. 11

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    NEDO is surveying the actual state of the coal related research/development in Japan to supply information on the coal related research/development in Japan to IEA`s coal research project database. This book of fiscal 1997 version includes 338 subjects. The details described are name of research institute, the section in charge, address, name of country, telephone No., name of joint researcher, research theme, classification, outline of research, project No., name of researcher, sponsor, the budget appropriated, term of research, remarks, etc. The books of data collected from each country in surveys of the actual state of the coal related R and D and IEA`s coal researches which have been made so far are submitted for general viewing at NEDO Information Center. Also, a part of those can be accessible from the energy database of which NEDO Information Center is performing on-line service for user members

  3. Multi-robot CAD/CAM welding system in heavy industries; Jukogyo ni okeru multi robot CAD/CAM yosetsu system

    Energy Technology Data Exchange (ETDEWEB)

    Sugimoto, Y.; Kanjo, Y. [NKK Corp., Tokyo (Japan)

    1996-08-01

    Described herein are activities in NKK Corp. for elementary techniques necessary for welding robots and systems, and the multi-robot CAD/CAM systems in which these techniques are integrated and commercialized. A high-speed, rotary arc welding method has been developed as the proprietary process that gives smooth, defect-free beads even at a high current and welding speed. It rotates arc over a molten pool by mechanical rotation of the electrode end. A multi-sensor system for coordinate transformation, and sensing work ends and bead joints has been also developed to correct position deviations, which are problems involved in a teaching play-back robot system. The multi-robot system is characterized by two or more multi-joint robots integrated in the system by the computer-aided CAD/CAM system to handle one work. A total of 36 systems have been already used for various industrial purposes, such as construction of bridges and production of ship panels. 8 refs., 24 figs., 2 tabs.

  4. Shift of the circumstances in effluent pollutant loads and water pollution in the Seto Inland Sea; Setonaikai ni okeru odaku fukaryo to suishitsu no hensen

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, T. [Hiroshima Prefectural Institute of Public Health and Environment, Hiroshima (Japan); Komai, Y. [Hyogo Prefectural Institute of Environmental Science, Kobe (Japan); Koyama, T. [Wakayama Prefectural Research Center of Environment and Public Health, Wakayama (Japan); Nagafuchi, O. [Fukuoka Institute of Health and Environment Science, Fukuoka (Japan); Hino, Y. [Kagawa Prefecture Environmental Research Center, Kagawa (Japan); Murakami, K. [Okayama Prefectural Institute for Environmental and Public Health, Okayama (Japan)

    1998-11-10

    The relationship between the shift of the amount of effluent pollutant loads and the quality of water in and after the 1970s is studied for the verification of the effect of wastewater control and pollution measures for the Seto Inland Sea. The pollution loads are analyzed using the population, sewerage system diffusion rate, industrial production amount, number of farm animals, etc., gathered from existing data, and the quality of water is analyzed using the surface layer data collected at 124 sites. Although population as the source of pollutant loads has enlarged, the enlargement does not bring about a significant change in the loads, this partly due to the diffusion of sewerage systems. The rates of reduction in the 1979-1994 period of COD (chemical oxygen demand), T-N (total nitrogen), and T-P (total phosphorus) are 25.2%, 5.3%, and 30.3%, respectively. COD has returned to the previous level, but transparency has turned poorer. T-N and T-P worsened in the 1985-1989 period, and have not yet returned to the levels of 1980-1984. Pollution is in progress in Osaka Bay, Hiroshima Bay, and some others. In some sea areas, transparency is improving, with COD and Chl.a on the increase. From the nutrient salt and Chl.a scatter diagrams, the potential of algal growth relative to the concentration of nutrient salts may be estimated. Organic pollution is affected by algal growth. The organic matters produced in the inland sea are approximately 20 times as much as the organic matters produced on land. 18 refs., 11 figs., 2 tabs.

  5. Hybrid learning algorithm integrating genetic algorithms with neural networks for saccade generation model; Saccade gankyu undo model ni okeru identeki algorithm to kobaiho no togogata gakushu algorithm

    Energy Technology Data Exchange (ETDEWEB)

    Arai, K. [Mitsubishi Chemical Corp., Tokyo (Japan); Aiyoshi, E. [Keio University, Tokyo (Japan)

    1997-01-20

    Saccade eve movements are among the most rapid vet precise of all movements produced by higher mammals. Recently we have proposed a spatio-temporal neural network model of the superior colliculus which uses lateral excitatory and inhibitory interconnections to help control both the dynamic and static behavior of saccadic eve movements. In this paper a new learning algorithm integrating genetic algorithms with neural networks for the lateral inhibitory and excitatory interconnections in the saccade generation model is presented. Data base for the training were obtained from neurophysiological experiments, and the training converged well even if random connections were chosen as initial conditions. The resulting network model succeeded in making accurate saccadic eve movements of a variety of sizes while producing realistic spatio-temporal patterns of collicular discharge. 18 refs., 8 figs., 1 tab.

  6. Phosphorus and nitrogen distributions and budget across the front in Osaka bay in winter; Toki no Osakawan ni okeru front to rin chisso no bunpu shushi

    Energy Technology Data Exchange (ETDEWEB)

    Yuasa, I.; Hashimoto, E.; Yamasaki, M. [Chugoku National Industrial Research Institute, Hiroshima (Japan)

    1996-09-30

    It is known that there exists a large-scale tidal front at the middle of Osaka Bay greatly affected by river water in the period from autumn into winter and that it plays an important part in the transportation of nutrient salts supplied from the land. Specimens were collected from car ferry engine cooling water once a month in winter, or in the period from November, 1986, through March, 1987, and were subjected to examination for the disclosure of monthly variations in the tidal front and in the distribution of phosphorus and nitrogen. In November, 1986, there was a remarkable difference in phosphorus and nitrogen concentration between the two sections divided by the tidal front while the difference was less in February, 1987, when a red tide occurred in the upper layer in the eastern part of the bay for the consumption of nutrient salts by Skeletonema costatum. This paper discusses the balance of PO4-P and DIN as learned from a simplified box model simulation of the upper layer water of the bay and reports that the variations in phosphorus and nitrogen observed in the box are like the variations that took place in the real bay water. 12 refs., 9 figs., 2 tabs.

  7. Present status of promotion of advanced safety vehicle in phase 2 (ASV2); Dai 2 ki senshin anzen jidosha (ASV) suishin keikaku ni okeru kenkyu jokyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-11-01

    For active safety enhancement, drivers will be provided with information and warning that will help them drive with safety. Studies are under way about functions to facilitate drivers' perception and to lighten the burdens imposed on them. As for accident avoidance techniques, onboard systems will perform controls involving vehicle maneuver for safety enhancement. This includes the improvement of vehicle maneuvering performance, in addition to brake control and steering control, for lightening drivers' burdens and for complementing their operating skill. Danger avoidance is based on the concept that the related system is to work in case warnings alone are not enough to avoid a collision. Full automation will be implemented by two ways, the autonomous way aided by the existing infrastructures such as GPS (Global Positioning System) or the way in which infrastructures to be newly built will be utilized. Passive safety technologies aim at minimizing damage upon collision, and involve structural improvement, air bags, etc. Disaster aggravation prevention means to prevent disaster from spreading after collision. Communication is one of safety-related elements on which studies will continue. Under the Phase 2 ASV program, research and development will be conducted for putting passenger cars to practical use, and the same will be conducted, in the case of large vehicles and motorcycles, for the construction of their prototypes. (NEDO)

  8. Lipid bodies and lipid accumulation in oleaginous plants and microorganisms; Yuryo shokutsu biseibutsu ni okeru lipid body to shishitsu no chikuseki

    Energy Technology Data Exchange (ETDEWEB)

    Kamisaka, Y. [National institute of Bioscience and Human Technology, Tsukuba (Japan)

    1995-10-20

    Recent advances in genetic engineering make it possible to design lipids produced by oleaginous plants and microorganisms. Mechanism for lipid accumulation and lipid body formation is one of the most important knowledge for the basis of the lipid designing technology. Recently extensive studies have been focused on the molecular structure of lipid bodies in plants, which reveals lipid body specific proteins termed oleosin. In microorganisms, however, much less is known about the molecular structure of lipid bodies. This paper reviews the chemical composition, enzyme activities and formation mechanism of lipid bodies in oleaginous plants and microorganisms. Recent works on diacylglycerolacyltransferase and lipid bodies in an oleaginous fungus, Mortierella ramanniana var. angulispora, are also described. Future works would be dedicated to answer questions about how proteins and lipids are assembled and sorted into lipid bodies. 75 refs., 5 figs., 2 tabs.

  9. Temperature effect on corrosion fatigue strength of coated ship structural steel; Zosen`yoko tosozai no fushoku hiro kyodo ni okeru ondo no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Takanashi, M.; Fuji, A.; Kojima, M.; Kitagawa, M. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan); Kobayashi, Y. [Ship Research Inst., Tokyo (Japan); Kumakura, Y.

    1997-08-01

    The corrosion fatigue life was obtained using uncoated and tar epoxy resin specimens to clarify the temperature effect. The life curve for corrosion fatigue of machined and uncoated steel in the air and sea was obtained. The fatigue strength of uncoated steel largely decreases in the sea and breaks even in the nominal stress range of less than 1/2 of the fatigue limit in the air. The effect of temperature on the coated steel is represented by a corrosion coefficient. The steel coated at 25{degree}C is 1/1.03 to 1/1.13 at 40 to 60{degree}C. This showed that the fatigue strength decreases when the temperature exceeds 25{degree}C. However, it has not such tendency and significance that are represented quantitatively. There is a slight difference in the short-life area between the crack generation life and breaking life. However, the long-life area has no significance that influences the whole evaluation. In the long-life corrosion fatigue, the crack occurs from the corrosion pit due to the exposure below the coated film and progresses in the base material before the coated film is destroyed. The effect of the corrosion pit remarkably appears at a low-stress level. 14 refs., 14 figs., 4 tabs.

  10. Measurement of static state variables in a direct drive electro-hydraulic servovalve; Chokudogata yuatsu servo ben ni okeru seiteki jotairyo no sokutei

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Y. [Yamanashi University, Yamanashi (Japan); Ouhi, H. [Yamanashi University, Yamanashi (Japan). Faculty of Engineering

    1999-09-15

    Making use of a direct drive servovalve's driving current, which is in proportion to the driving force, and the spool displacement obtained from a built-in LVDT, it is possible to get the state variables such as flow force, flow rate and load pressure for the purpose of valve control without attaching other transducers on the servovalve. In this paper, experiments were carried out using different loads. With PWM driving, no hysteresis appeared regardless of the flow rate. Because of the flow force compensation on the spool of the valve used in the experiment, an empirical equation was used for calculation of the flow rates from the measured flow forces. Under different loads, the calculated flow rates were in consistence with the measured ones. Then, load pressures were obtained from the calculated flow rates, with the discharge coefficients acquired using empirical equations. The calculated load pressures were in good agreement with the measured results. (author)

  11. Studies on substitutional protein sources for fish meal in the diet of Japanese flounder; Hirame shiryo ni okeru miriyo shigen no riyo

    Energy Technology Data Exchange (ETDEWEB)

    Kikuchi, K.; Furuta, T.; Sakaguchi, I. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1996-08-01

    Effectiveness of livestock industry wastes and vegetable protein added to fish meal in fish farming is tested by feeding the Japanese flounder. In the experiment, a part or the whole of the fish meal protein is replaced by the meat meal (MM), meat and bone meal (MBM), corngluten meal (CGM), or dried silkworm pupa meal (SPM), and fries of the Japanese flounder are fed on the new diets for eight weeks. On a diet containing 60% or less of MM, no change is detected in the fish in terms of increase in weight, protein efficiency ratio, and blood components, indicating that 60% at the highest of fish meal may be replaced by MM. In the case of MBM, it can occupy approximately 20%. As for CGM, the proper substitution rate is approximately 40%. Essential amino acids that the new diets may lack are added for an approximately 10% improvement on the result. The SPM substitution works up to 40%, when, however, the blood components are degraded. The proper substitution rate is therefore placed at approximately 20%. 38 refs., 2 figs., 17 tabs.

  12. Bearing life in contaminated oil and oil passing into bearing for tapered roller bearing; Ensui koro jikuuke ni okeru ibutsu yuchu deno jumyo to kantsu yuryo

    Energy Technology Data Exchange (ETDEWEB)

    Asai, Y.; Oshima, H.; Sakamoto, K. [Koyo Seiko Co. Ltd., Osaka (Japan)

    1997-10-01

    In this paper a relationship between depth of dents, area of dents gathered and bearing life has been investigated for tapered roller bearings used in differential gear case. It is effective for the longer bearing life to reduce hard particles of Fe especially among several contaminations existing in the gear case. It is also effective to make oil level lower in the case from the view point for reduction of number of dents. 8 refs., 8 figs., 4 tabs.

  13. Numerical simulation of fuel sprays and combustion in a premixed lean diesel engine; Kihaku yokongo diesel kikan ni okeru nenryo funmu to nensho no suchi simulation

    Energy Technology Data Exchange (ETDEWEB)

    Miyamoto, T.; Harada, A.; Sasaki, S.; Shimazaki, N.; Hashizume, T.; Akagawa, H.; Tsujimura, K.

    1997-10-01

    Fuel sprays and combustion in a direct injection Premixed lean Diesel Combustion (PREDIC) engine, which can make smokeless combustion with little NOx emission, is studied numerically. Numerical simulation was carried out by means of KIVA II based computer code with a combustion submodel. The combustion submodel describes the formation of combustible fuel vapor by turbulent mixing and four-step chemical reaction which includes low temperature oxidation. Comparison between computation and experiment shows qualitatively good agreement in terms of heat release rate and NO emission. Computational results indicate that the combustion is significantly influenced by fuel spray characteristics and injection timing to vary NO emission. 10 refs., 8 figs., 1 tab.

  14. Study on the behavior of reaction disk in the vacuum brake booster; Shinkushiki bairyoku sochi ni okeru reaction disk no kyodo kaiseki jikken

    Energy Technology Data Exchange (ETDEWEB)

    Kuroda, M.; Sawada, T.; Kato, Y. [Tokyo Univ. of Agriculture and Technology, Tokyo (Japan); Ogawa, E.; Nakamura, S. [Jidosha Kiki Co. Ltd., Tokyo (Japan)

    1997-10-01

    Vacuum brake booster has been widely applied in automobiles, and it needs much time for experiments in order to design a new type model and so on. In this report concentrating on the behavior of a reaction disc, it was simulated by ARAQUS FEM program where coefficients of rubber disc are Mooney-Rivlin constants. It was shown that the numerical results represent good agreement with experiments, and in addition that values of jumping force which shows the starting point of the brake increases with the increment of the hardness of the disc, clearance and so on. 2 refs., 10 figs.

  15. Effects of fuel and air mixing on WOT output in direct injection gasoline engine; Chokufun gasoline kikan ni okeru nenryo to kuki no kongo to shutsuryoku seino

    Energy Technology Data Exchange (ETDEWEB)

    Noda, T.; Iriya, Y.; Naito, K.; Mitsumoto, H.; Iiyama, A. [Nissan Motor Co. Ltd., Tokyo (Japan)

    1997-10-01

    The effects of in-cylinder charge motion and the characteristics of the fuel spray and piston crown shape on WOT output in a direct injection gasoline engine are investigated. The fuel and air mixing process in a cylinder is analyzed by computer simulation and LIF method visualization. As a result, the technical factors to achieve enough mixing in a DI gasoline engine equipped with bowl in piston optimized for stratified combustion are clarified. 7 refs., 9 figs., 1 tab.

  16. Continuous cooling transformation behavior for heat treatment of spheroidal graphite cast iron. Kyujo kokuen chutetsu no netsushoriji ni okeru renzoku reikyaku hentai kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Nakata, T.; Matsumoto, H. (Shibaura Institute of Technology, Tokyo (Japan)); Kasugai, T. (National Research Institute for Metals, Tsukuba (Japan)); Koyama, M. (Automobile Foundry Co. Ltd., Yokohama (Japan))

    1992-08-25

    In order to study basic heat treatment properties of spheroidal graphite cast iron, the continuous cooling transformation(CCT) diagrams for the material equivallent to FCD700 under various austenitized conditions were obtained. There were 4 kinds of austenitized conditions varying from 1123K and 420s to 1323K and 1,800s. Eight kinds of cooling time from the austenitized temperature to 773K ranged from 6s to 4,000s. The transformation temperature was measured by a thermal expansion method. When the austenitized temperature was increased from 1123K to 1323K, ferrite and pearlite transformation regions moved a little in the CCT diagrams and the martensite transformation temperature decreased from 493K to 458K. The bainite region in the CCT diagrams disappeared at the austenite temperatures above 1223K. The nucleation sites of ferrite and pearlite in the spheroidal graphite cast iron were generated at grain boundary between austenite and graphite but not at grain boundary between austenites. The reason of such phenomena was also studied. 10 refs., 8 figs., 2 tabs.

  17. Isothermal transformation behavior in 12%Cr-0.3%C steel; 12%Cr-0.3%C ko ni okeru koon hentai kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Mikami, M. [Japan Casting and Forging Corp., Kitakyushu (Japan); Tsuchiyama, T.; Takaki, S. [Kyushu Univearsity, Fukuoka (Japan)

    2001-01-01

    In order to get fine grain of large martensitic stainless steels products, it is available to use the isothermal transformation before the austenitizing. When 12%Cr-0.3%C steel is subjected to the full solution treatment and following isothermal transformation at 900-1,020K, it is observed that the microstructures are affected by the isothermal ageing temperature. The microstructure transformed isothermally at 1,020K is the full eutectoid structure where carbides precipitate homogeneously. On the other hand, the microstructure transformed at 900K is the mixed heterogeneous structure: the eutectoid structure where carbides precipitate densely around the edge of prior austenite grains and the ferrite structure where carbides hardly precipitate in the center of prior austenite grains. These phenomena are concerned with the decreasing in carbon content in the untransformed austenite as the eutectoid transformation progresses. The amount of decreasing in carbon at 900K is larger than at 1,020K, which causes the shortage of carbon in austenite in the last period of isothermal transformation. In the case of the isothermal transformation at 900K, the reason of why there are the ferrite structures with no carbide in the center of prior austenite grains is that the massive transformation is induced by the shortage of carbon in untransformed austenite. (author)

  18. Composition dependence of the rate of bainitic transformation in Cu-Zn-Al alloys; Cu-Zn-Al gokin ni okeru bainite hentai sokudo no gokin sosei izonsei

    Energy Technology Data Exchange (ETDEWEB)

    Tabuchi, M.; Marukawa, K. [Hokkaido University, Sapporo (Japan). Faculty of Engineering

    1998-04-20

    The bainitic transformation is known to have an intermediate nature between the martensitic transformation and the diffusional transformation, while its transformation mechanism has not yet been clarified precisely. If this transformation involves lattice shearing like the martensitic transformation, it should take place more easily in those alloys which have a higher tendency to transform martensitically. On this expectation, the composition dependence of bainitic transformation kinetics has been studied in Cu-Zn-Al alloys. Especially, the relation between the martensitic transformation temperature (Ms) and the bainitic transformation rate was examined. The transformation process was traced by measuring the electrical resistivity of specimens during aging. It was found that the transformation rate is higher in those alloys having a higher Ms temperature. The activation energy for the process, obtained from its temperature dependence, is independent of the alloy composition and roughly equal to that for solute diffusion in the parent alloy. This indicates that the transformation is controlled by diffusion of solute atoms. The composition dependence of the bainitic transformation rate is discussed in terms of a diffusion controlled growth theory. 15 refs., 7 figs., 3 tabs.

  19. Holdup of O/W emulsion in a packed column for liquid membrane separation of hydrocarbon; Tankasuiso no ekimaku bunri ni okeru jutento nai no emarushon horudo appu

    Energy Technology Data Exchange (ETDEWEB)

    Egashira, R.; Sugimoto, T.; Kawasaki, J. [Tokyo Inst. of Technology, Tokyo (Japan). Faculty of Engineering

    1993-07-10

    Liquid membrane separation of hydrocarbon is an energy saving separation method that is expected of practical use. If the method uses a packed column, the holdup of O/W emulsion affects the effective contact area and residence time of the emulsion. Therefore, this paper describes an attempt to correlate the dynamic emulsion holdup in a packed column in liquid membrane separation of hydrocarbon with property values of the emulsion and external oil phase, and operation variables. The experiment used a mixture of toluene + n - heptane + n - decane for oil phase in the O/W emulsion and saponin aqueous solution for liquid phase (liquid membrane phase). The packed column with an inner diameter of 37 mm used stainless steel McMahon packing. As a result of the experiment, the dynamic emulsion holdup showed a correlation according to the Reynolds number and Galilei number, regardless of whether the emulsion permeates the liquid membrane. The correlation made it possible to estimate in a simple manner the emulsion holdup in the packed column when this separation method is used. 5 refs., 3 figs., 3 tabs.

  20. Optimization of man-machine roll allocation in automatic systems; Jidoka system ni okeru hito to kikai no yakuwari buntan no saitekika

    Energy Technology Data Exchange (ETDEWEB)

    Yamasaki, H. [Yokokawa Electric Corp., Tokyo (Japan). Research and Development Lab.

    1996-08-10

    Bearing reliability and safety of automatic systems in mind, man-machine roll allocation in the operation of facilities is examined, and the optimal roll allocation is proposed. The outline of the method for man-machine roll allocation is given in process instrumentation system, robotized assembly plant, railroad operation control system, and passenger airplane operation control system. The types of man-machine roll allocation in automatic system is divided into normal and emergency cases. Improvement in the total reliability of man-machine system can be expected by man-machine mutual complementary roll allocation. The core of the intelligent support system for emergency is the growing knowledge base, and the system performs intelligent support automatically or with the support of human in an emergency. For smooth man-machine information interchange at man`s own will, logical difference between man and machine must be adjusted in the man-machine interface. 8 refs., 2 tabs.

  1. Development of transition equipment shared with urban CATV in distribution automated pair area; Haiden jidoka pair area ni okeru toshigata CATV tono kyoyoka iko kizai no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Nonaka, H. [Kansai Electric Power Co. Inc., Osaka (Japan)

    1998-04-10

    The transmission medium for remote switch control during overall distribution automation selects a coaxial cable in the area, where the CATV carrier plans, and evades the doubled transmission path and congested facilities for economical facility construction when the transmission path is shared. In the area where the switch has been already remotely controlled by a pair transmission path, however, the type of the transmission path differs from for urban CATV with the optical and coaxial transmission paths as a medium. Therefore, the transmission path cannot be shared. The transmission path is then doubled, and the aerial facilities are congested. In this study, the slave station of the switch installed for a pair transmission path is effectively used to develop the required equipment and make a field test for the subsequent shared use at minimum cost. The equipment on the substation`s slave station side is pair/optical terminal equipment (center distribution wave system) and pair/coaxial terminal equipment (substation distribution wave system). The equipment on the switch`s slave station side is a coaxial/pair conversion adapter (common). As a result of the field test, the validity was verified. 4 figs.

  2. Automatic operation technologies adapted in No.3 hot strip mill at Chiba works; Chiba seitetsusho dai 3 netsuen kojo ni okeru jidoka mujinka gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Yoshimura, H.; Kawase, T.; Maeda, I. [Kawasaki Steel Corp., Tokyo (Japan)

    1997-03-01

    Concept of automatic/unmanned operation at the Kawasaki Steel Chiba Works and the facilities concerned are introduced. The endeavor for the development of the automatic/unmanned operation technology was exerted with a motto `rolling work by three operators in one control room.` At the entry side, DHCR (Direct Hot Charge Rolling) material is taken in synchronously with the continuous caster and then inserted into the heating furnace. In the case of HCR (Hot Charge Rolling) or CCR (Cold Charge Rolling) material, positioning of the received slab, slab handling after the determination of the slab rolling order, and insertion into the heating furnace are carried out automatically. In the rolling process, in which no need of manual assistance is the target, the mill is fully equipped with sensors for detecting the distance between the rolling stands, and the like, and high precision has been achieved. In the control of mill pacing, automation has realized through close coordination between a strictly defined transfer prediction model, heating furnace combustion control, and coil yard operation. At the delivery side, the coiling process and the transfer of coils are accomplished automatically. 9 refs., 11 figs., 3 tabs.

  3. Power supply facilities and comprehensive power distribution automation system at the Kansai International Airport; Kansai kokusai kuko ni okeru denryoku kyokyu setsubi oyobi haiden sogo jidoka system

    Energy Technology Data Exchange (ETDEWEB)

    Kawasaki, Y. [Kansai Electric Power Co. Inc., Osaka (Japan)

    1995-07-01

    This paper introduces the power supply facilities and the comprehensive power distribution automation system using an optical network installed at the Kansai International Airport that has begun operation. The power supply has adopted a three-line spot network system for the 22-kV system, a system to supply power from multiple number of distribution towers using a constant reserve system for the 6-kV system, and a system to supply power from high-voltage transformers for 100 to 200 V systems. As a conduit used to deal with subsidence of the power supply cable path, a pipe was developed that combines a PE-made flexible pipe with a cable protecting expansion steel pipe. The power distribution towers were given considerations for environmental harmony, size reduction, heavy salt damage, and measures for soft soil ground. The comprehensive power distribution automation system performs remote control of switches, operation of remote detectors, and load survey. Cost reduction has been realized in the system by adopting an optical multi-drop system that uses an air blown fiber (ABF) construction method. An optical shunt having eight branches was developed for this construction method. The ABF method blows optical fibers having two to eight cores into a hollow plastic pipe by using compressed air. 10 figs.

  4. Development of automatic technology of drilling, loading and hauling operation for crushed stone industry; Saisekigyo ni okeru ganseki saishu sagyo no jidoka gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Miyake, K. [Japan Crushed Stone Association, Tokyo (Japan); Yoshida, K.; Oshima, H. [Komatsu Ltd., Tokyo (Japan); Suzaki, T. [Furukawa Co. Ltd., Tokyo (Japan)

    1996-07-25

    In the crushed stone industry, work must be done outdoors for long hours, and labor shortage becomes a serious problem because of the extremely rigorous work environment. In this paper, the content of three technical developments recommended by the Japan Crushed Stone Association was introduced: that is, the automatic technology on the crawler drill, the automatic technology on the wheel loader, and the unmanned operating technology on the dump truck. As for the automatic technology on the crawler drill, the multi-operating levers and the fully automatic load exchange equipment were under development for more safely and simply operating the oil hydraulic crawler drill in the rock drilling operation. As for the automatic technology on the wheel loader, a system to prevent tire slip, an automatic mining system, and an automatic loading system were developed. As for the unmanned operating technology on the dump truck, a system to measure direction and distance were developed using an optical fiber gyroscope as a direction sensor and the vehicle rotating sensor as a distance sensor. 8 refs., 29 figs., 2 tabs.

  5. Power system harmonics regulations and the suppression technologies. 4. Suppression technologies in large converter systems; Dengen kochoha kisei to taio gijutsu. 4. Daiyoryo kiki ni okeru taio gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Takeda, M. [Mitsubishi Electric Corp., Tokyo (Japan)

    1995-08-20

    Capacity increase and efficiency improvement have become possible as a result of increasing the voltage and capacity in power semiconductors. On the other hand, the amount of harmonic current generated is increasing. Discussions have been given on the harmonics suppression technologies in order to suppress damages given by voltage distortion in the power system to devices connected in the same system. Among the representative harmonics suppression measures for large-capacity devices, the measure applied to the device side is pulse multiplication and use of PWM in power converters as the source of harmonics generation. Systems that absorb harmonics generated from converters by filters use active filters and passive filters (L-C filters). A separately excited three-phase bridge circuit suppresses the harmonics by offsetting harmonic currents with each other by using a multiplied pulse system with shifted phase angles. A cycloconverter uses, together with the pulse multiplication, an active filter to absorb low-order harmonics. A large-capacity self-excited converter uses a multiplex transformer system to increase the number of synthesized pulse and suppresses harmonics by using the multiplied pulse PWM system. 7 refs., 5 figs.

  6. Calculation of wave resistance by using Kochin function in the Rankine source method; Rankinsosuho ni okeru kochin kansu wo mochiita zoha teiko keisan

    Energy Technology Data Exchange (ETDEWEB)

    Yasukawa, H. [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

    1997-10-01

    In order to avoid negative wave resistance (which is physically incomprehensible) generated in calculating wave resistance by using the Rankine source method, a proposal was made on a wave resistance calculation method using the Kochin function which describes behavior of speed potential in regions far apart from a hull. The Baba`s condition was used as a free surface condition for the speed potential which expresses wave motions around a hull. This has allowed a new Kochin function which uses as unknown the speed potential on the hull surface and the free surface near the hull to be defined and combined with the Rankine source method. A comparison was made between the calculated values for wave resistance, hull subsidence and trim change of an ore transporting vessel (SR107 type of ship) in a fully loaded condition and the result of water tank tests. The wave resistance values derived from pressure integration have all become negative when the Froude number is from 0.1 to 0.2, while no negative resistance has appeared in the calculations by using the Kochin function, but the result has agreed with that of the water tank tests. Accuracy of the calculations at low speeds was improved. The trim change in the calculations was slightly smaller than that in the water tank tests. The subsidence showed a good agreement. 7 refs., 1 fig.

  7. Characteristic analysis of turbulent heat diffusion in a multi-compartment structure; Takukakuka kukan kozo ni okeru ranryunetsu kakusan gensho no kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Hu, C.; Fukuchi, N. [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1997-10-01

    An analysis was made on turbulent heat diffusion in a multi-compartment structure necessary for designing calorific power and environment for functional systems used in marine vessels and off-shore structures. In a multi-compartment structure, the diffusion phenomenon is complex because of movement of air flow in turbulence and buoyancy resulted from non-isothermal condition. The phenomenon is largely affected by space shapes and walls, and the conditions in heat diffusion field is governed also by shapes of opening connecting the compartments. An analysis was made by using the SIMPLE method on turbulent heat diffusion in a multi-compartment space with high Raleigh number in which natural convection is dominant. If the opening is small, the Coanda effect appears, in which air flow passing through the opening rises along the wall, wherein a high-temperature layer is formed near the ceiling, making the heat diffusion inactive. If the opening is large, a jetting flow from the opening and a large circulating flow are created, which cause active advection mixture, making temperature gradient smaller in the upper layer. Heat transfer intensity in an opening on a partition wall decays in proportion with 1/4th power of the opening ratio. 7 refs., 11 figs.

  8. Travel time and ray path computation in 2D-heterogeneous structures; Fukinshitsu kozo ni okeru jishinha soji oyobi hasen no atarashii keisan hoho

    Energy Technology Data Exchange (ETDEWEB)

    Fujie, G.; Kasahara, J.; Sato, T.; Mochizuki, K. [The University of Tokyo, Tokyo (Japan). Earthquake Research Institute

    1996-05-01

    Methods were studied for determining the initial travel time and ray paths with stability when an non-linear travel time inversion is performed in an inhomogeneous structure. The travel time calculation was based on Faria and Stoffa`s method. First, the 2-dimension space was sectioned by grids, and `slowness` was assigned to all the lattice points. Starting from the vibration source, travel time at each lattice point is sequentially calculated. This method calculates travel time for any structure without breakup. In this study, an algorithm more sophisticated than the method of Faria, et al., was developed, and the improvement of travel time calculation accuracy led to the accurate determination of the direction of incidence into the lattice points during the initial motion. The calculation of ray paths was effected by tracing back from the receiving points the incidence into the lattice points or by following back the ray paths to the vibration source. This method performs stable calculation for a heavily inhomogeneous structure and, with the algorithm being simple, do the parallel programming as well. 1 ref., 6 figs., 1 tab.

  9. 2D resistivity survey in complex geological structure area. Application to the volcanic area; Fukuzatsuna chishitsu kozo chiiki ni okeru hiteiko nijigen tansa. Kazangan chiiki deno tekiorei

    Energy Technology Data Exchange (ETDEWEB)

    Asakawa, S.; Ikuma, T.; Tanifuji, R. [DIA Consultants Co. Ltd., Tokyo (Japan)

    1996-05-01

    Introduced herein is an application of 2D resistivity survey to a volcanic rock area where the survey result is difficult to interpret because of its complex geological structure. In a dam site survey, main problems involve the permeability of water through faults and weathered, altered zones. At this site, a 2D resistivity survey was conducted, a 2D geological structure was deduced from the resistivity section, and the result was examined. It was found that resistivity distribution was closely related to hydrographic factors, but no obvious correlation was detected between rock classes and R, Q, and D. In conducting investigations into a section planned for a highway tunnel, it was learned that the problem was a volcanic ash layer to collapse instantly upon absorbing water, and the distribution of the ash layer, not to be disclosed by boring, was subjected to a 2D resistivity survey. The survey was conducted into the structure above where the tunnel would run, and further into the face, and studies were made about what layer was reflected by the resistivity distribution obtained by analysis. The result of the analysis agreed with the details of the layer that was disclosed afterward. 4 figs., 1 tab.

  10. Flow characteristics of Hijiori HDR reservoir form circulation test in 1995; Koon tantai Hijiori jikkenjo ni okeru shinbu choryuso yobi junkan shiken (1995 nendo) kekka to ryudo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Fukushima, N.; Hyodo, M.; Shinohara, N.; Takasugi, S. [Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan)

    1996-05-01

    This paper reports the result of a preliminary circulation test conducted in fiscal 1995 on a deep reservoir (at a depth of about 2200 m) in the Hijiori hot dry rock experimental field. One water injection well and two production wells were drilled to constitute a circulation loop, to which the circulation test was performed to investigate the flow characteristics thereof. The result revealed the following matters: total amount of injected water of 51500 m{sup 3} resulted in a total fluid recovery rate of about 40%; as a result of well stimulation given twice during the initial stage of the water injection, the continuity impedance in the vicinity of the injection well decreased largely (however, the continuity improvement upon the second attempt was considerably inferior to that from the first attempt); and increase in the water injection amount does not necessarily lead to increase in the production amount. The paper describes additionally that it is extremely difficult to interpret non-linearity between the injection and production amounts by using a model prepared previously with a main objective to analyze the Hijiori HDR circulation system. 1 ref., 9 figs., 1 tab.

  11. Cooperative measurements of microtremors in the north-eastern region of Nishinomiya city, Hyogo Pref.; Nishinomiyashi hokutobu ni okeru joji bido no godo kansoku

    Energy Technology Data Exchange (ETDEWEB)

    Maiguma, T.; Matsuzawa, H. [Saitama University, Saitama (Japan). Faculty of Engineering; Sawada, Y.; Tazawa, Y. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1996-05-01

    For the purpose of generally grasping space distribution of ground vibration characteristics, cooperative measurements were conducted in a wide area, mainly in the area stricken by the M7 earthquake. Forty-five organs such as governmental institutes, universities, and private company institutes participated in the measurements which were conducted at 1967 measuring points. The area which the author is in charge is an area from the north of Nishinomiya City to the south of Takarazuka City. The area is relatively far from the hypocenter area, but the magnitude is 7 there and damage was concentrated. The measurements were made by each independent team from August 29 to September 1, 1995. As a result of spectral measurements of NS, EW and UD components, conspicuous peaks were seen in an extent of 1.5 sec. cycle in almost all measuring points and components. Further, in spectra of horizontal motion components of A measuring point group, conspicuous peaks were seen in an extent of 0.15-0.5 sec. cycle, and in those in B and C measuring point groups, in an extent of 0.35-0.5 sec. cycle. In upper/lower motion components, conspicuous peaks were seen in an extent of 0.3 sec. cycle in A measuring point group. 4 figs.

  12. Application of streaming potential method for detection of fractures in granitic rock; Kamaishi kozan ni okeru ryutai ryudo den`iho tekiyo shiken

    Energy Technology Data Exchange (ETDEWEB)

    Negi, T.; Yokoi, K.; Yoneda, Y. [Nittetsu Mining Co. Ltd., Tokyo (Japan); Senba, T. [Power Reactor and Nuclear fuel Development Corporation, Tokyo (Japan)

    1996-05-01

    Measurements were made using the streaming potential method for the purpose of investigating the expansion of hydration cracks, direction of their propagation, and the chaining of cracked surfaces, in the granitic rock. Tests were conducted by use of a bore hole in the gallery wall. The bore hole yielded approximately 400 liters of water per minute, the bore hole was closed and then opened, and the change with the passage of time in the spontaneous potential (SP) on the gallery wall was measured. At a spot 31.2m from the mine entrance, the SP dropped by 15mV simultaneously with the opening of the bore hole, and rose by 14mV simultaneously with the closure of the same. The phenomenon was true for other locations, that is, for the section from the mine entrance to a spot 9.0m therefrom, and for a section beginning at 15.0m and ending at 19.2m therefrom. No change in the SP was observed in a group of cracks with water springing out of the gallery roof, beginning at a point 40m and ending at a point 54m from the mine entrance. The result suggests the possible application of the streaming potential method to the investigation of cracks. 1 ref., 10 figs.

  13. Application of geophysical methods to investigation of old castle, especially of the moat; Joshi no chosa ni okeru butsuri tansa no tekiyo (horiato no tansa)

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, A.; Karube, F.; Kobayashi, M.; Toge, M. [OYO Corp., Tokyo (Japan)

    1996-05-01

    An explanation is made about the application of geophysical methods to the investigation of the ruins of old castles especially of their moats. Techniques currently in use for exploration of the ruins of castles are mainly underground radar exploration and electric exploration. The underground radar method sends electromagnetic waves through the ground and receives the reflection for a high-precision exploration of the layers shallow in the ground. Therefore, this method is suitable for probing the ruins of castles relatively shallow in the flat land, hills, and mountains. The electric method (resistivity image method) do the probing by use of the two-electrode arrangement, performs inverse analysis on the basis of the obtained data for the determination of the underground resistivity distribution, and displays the distribution in an image easy to read. This method, when there is a great separation between the two electrodes, explores relatively deep into the ground. Thanks to this feature, this method is effective in probing relatively wide and deep ruins of moats, that is, the ruins of moats of castles built in later years, especially of those then filled with water. 2 refs., 5 figs.

  14. Flow characteristic of Hijiori HDR reservoir from circulation test in 1991; Koon tantai Hijiori jikkenjo ni okeru senbu choryuso shiken (1991 nendo) kekka to ryudo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Shiga, T.; Hyodo, M.; Shinohara, N.; Takasugi, S. [Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan)

    1996-05-01

    This paper reports one example of flow analyses on a circulation test carried out in fiscal 1991 at the Hijiori hot dry rock experimental field (Yamagata Prefecture). A fluid circulation model was proposed to simulate an HDR circulation system for a shallow reservoir (at a depth of about 1800 m) demonstrated in the circulation test by using an electric circuit network (which expresses continuity impedance in resistance and fluid storage in capacitance). Storage capacity of the reservoir was estimated by deriving time constant of the system from data of time-based change in reservoir pressure associated with transition phenomena during the circulation test. The storage capacity was estimated separately by dividing change of storage in the reservoir by change in the reservoir pressure. To derive the storage in the reservoir, a method to calculate non-recovered flows in the circulation test was utilized. The results of evaluating the reservoir capacity in the shallow reservoir using the above two independent methods were found substantially consistent. 3 refs., 6 figs., 1 tab.

  15. Magnetotelluric investigation in and around southern part of Hidaka metamorphic belt in Hokkaido, Japan; Hidaka henseitai nanbuiki ni okeru MT kansoku

    Energy Technology Data Exchange (ETDEWEB)

    Sato, H.; Utsugi, M.; Hirano, K.; Doi, T.; Nishida, Y.; Arita, K. [Hokkaido University, Sapporo (Japan)

    1996-05-01

    An MT observation was conducted in the Hidaka district, Hokkaido, for the estimation of the 2D resistivity structure in the southern part of the metamorphic belt, when frequencies of the VLF, ELF, and ULF bands were used. An approximately 42km-long traverse line was set to cross the Hidaka metamorphic belt from east to west. As for the observation points, 48 VLF points, 16 ELF points, and 4 ULF points were provided. During the data processing, impedance tensor was calculated in the frequency domain for the determination of the apparent resistivity relative to frequency and the phase difference. As the result, it was found that there is a fairly large resistivity gap between observation spots MNS and KWR and that the boundary corresponds to the Hidaka metamorphic belt, that the metamorphic belt that is reflected as a conspicuous high-resistivity layer in the VLF-, ELF-MT slopes down toward the east and has a distribution as deep as 10km in the vicinity of observation point KWR, that this high-resistivity layer sandwiches a low-resistivity layer at a depth of 5-7km, and that on the east side of the metamorphic belt there is a medium-resistivity layer creeping under the belt from the east side toward the west side. 5 refs., 6 figs.

  16. Low-NOx combustion on regenerative burner systems in an industrial furnace; Kanetsuroyo chikunetsu saisei burner ni okeru tei NOx ka gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Nishimura, M.; Suzuki, T.; Nakanishi, R.; Kitamura, R. [Kobe Steel, Ltd., Kobe (Japan)

    1996-05-01

    This paper describes the injection combustion experiments using low-NOx regenerative burner and its application to the forging furnace. For this combustion, the fuel was separately injected on an angle to the axis of the air stream. The mixing of fuel and air was restricted at the initial stage of combustion. The mixing combustion proceeded with separating the burner. The flue gas was exhausted with self-recirculation. With increasing the injection angle (difference between the injection angles of fuel and air), the NOx concentration was lowered when the velocity ratio of fuel/air injection was 1.34. The NOx concentration decreased by the increase of fuel injection velocity. For the industrial furnace, it had better set the combustion and idle periods mutually. The NOx concentration increases with increasing the temperature, qualitatively. The temperature in the axis of fuel injection was lower than the other region. For the forging furnace using existed original burners and modified low-NOx burners, the NOx concentration increased with increasing the proportion of original burners. When the modified burners were used, the NOx concentration was below 50 ppm even above 1,000 centigrade inside the furnace. For the modified burners, the fuel can be saved and the period for temperature up can be shortened. 4 refs., 12 figs.

  17. Experiments of off-shore ocean thermal energy conversion system in sea area at Toyama bay. Toyamawan ni okeru yojogata kaiyo ondosa hatsuden system no jitsukaiiki jikken

    Energy Technology Data Exchange (ETDEWEB)

    Takazawa, H.; Amano, M.; Kajikawa, T. (Electrotechnical Laboratory, Tsukuba (Japan))

    1991-04-24

    Because of the fact that the sea water in the Toyama Bay has water temperature difference of more than 20 {degree}C between at the surface layer and the deep layer, and the water scooped up from the deep layer has a nutritious salt effect beneficial to the local fishery, an applicability of the ocean thermal energy conversion was experimented at the actual sea area. The evaporator used as an energy self-supply equipment rated at 3.5 kW output is a hybrid type, in which a spray surface evaporation is carried out in the same shell as for a pool boiling. The condenser is of a perpendicularly flowing membrane condensation type. The heat transfer pipes in these heat exchangers use aluminum alloy material, with the interior processed with sea water resistant resin. The evaporator has eight spray nozzles for the working fluid, which are so arranged that the fluid jetting distributes the fluid uniformly over the whole heat transfer pipes, and the optimum amount of circulation was 10 tons/h. Heat transfer pipes for the condenser had the heat transfer performance reduced to half because of being resin coated. Itis necessary to reduce contact resistance especially between the resin and the base material. Since the evaporator {prime}S heat exchanging performance is decreased in about 15 days when conraminated biologically, the unit should preferably be cleaned within that period of time. An output of 3 kW was obtained at a temperature difference of 20 {degree}C, which suggests that the system can be self-supplied of the required energy if the sea water is scooped from the deep layer at a rate of about 0.3 ton per second. 7 refs., 7 figs., 1 tab.

  18. Heat insulating modification of a residential house existing in Hokkaido, and the effect; Hokkaido no kison kodate jutaku ni okeru dannetsu kaishu to sono koka

    Energy Technology Data Exchange (ETDEWEB)

    Ogasawara, K.; Akao, K. [Hokkaido Electric Power Co. Inc., Sapporo (Japan)

    1998-03-24

    A study is made about the airproof heat-insulating modification of a residential house in existence for the purpose of improving on its basic performance related to heating and airing. The house modified in this report is a residence typical of the ordinary wooden ones constructed in about 1985 or before. It had a 10K-100mm glass wool layer filling up the outer wall center section, but it is supposed that there had been a serious degradation in heat insulating effect since the equivalent gap area was found to exceed 15cm{sup 2}/m{sup 2}. The modification consisted of outside insulation by a lining provided on the external surfaces of the external material and insulation provided on the external surfaces of the floor base, with the insulation thickness complying with the new energy-saving criteria. The findings are mentioned below, obtained by comparing temperatures and heating energy consumption rates before and after the modification. The heating effect has been improved now that the difference in temperature has grown smaller between the upper and lower levels in the living room and that the living room floor surface temperature is now sensed to have risen. The sheltering performance of the house has been clearly improved in view of a rise in temperature, and a reduction in outdoor temperature dependence, of the porch space not covered by the heating system. The heating energy consumption rate has decreased to approximately 1/3. 5 refs., 6 figs., 1 tabs.

  19. Optimal allocation of handling equipment in a container terminal using dynamic programming with lagrangian relaxation approach. Container futo ni okeru niyaku shisetsu haichi no saitekika

    Energy Technology Data Exchange (ETDEWEB)

    Inamura, H. (Tohoku University, Sendai (Japan). Faculty of Engineering); Sritharan, S.; Villamor, N.

    1991-07-15

    This study describes methods for optimal crane allocation and the corresponding trailer allocation using dynamic programming with Lagrangian relaxation approach, taking the container terminal at Bangkok Port as an example. The developed system can be applied to any container terminal in any country regardless of number of berth, kind of container ship or kind of crane and trailer. This system may be used practically because the required solution can be derived from a personal computer operation for about ten minutes. The dynamic programming system relating to optimal crane allocation has been verified for its reasonability after 1000 repetitions of the simulation. Differences in the result were 1 TEU for the mean value, 12 TEU for the standard deviation, and {minus}30 to {plus}30 for the range. The standard deviation is sufficiently small at little less than 7% against a handling volume of 186 TEU. 15 refs., 4 figs., 6 tabs.

  20. Fire preventive function of parks at the great Hanshin-Awaji earthquake and recovery of trees; Shinsai ni okeru koen ryokuchi no ensho boshi kino to jusei kaifuku

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, H.; Hayakawa, S. [Yamaguchi Univ., Yamaguchi (Japan). Faculty of Agriculture; Suzuki, Y. [Kyushu Univ., Fukuoka (Japan). Faculty of Agriculture

    1997-09-01

    As a lot of houses and buildings were fired owing to urban fire at center of Nagata-ku, Kobe City on the Hanshin Awaji Great Earthquake on January, 1995, some examples that spread of the fire to the houses and others was stopped by green land of urban park and trees surrounding the houses were found. In this paper, outline of some case studies and active recovery states of damaged trees were investigated on fire preventive function of the trees planted in park green lands as well as on areas of fired houses. In the report of the Kanto Great Earthquake, it was also recorded that the green land space functioned as a fire shielding zone on fire and prevented spread of the fire on urban fire. In this in-situ survey, the fire preventive function of the trees such as park trees, garden trees and so forth was also confirmed on the fire after earthquake. Now, a part of the trees planted in the park was cut down, to construct some temporary houses at the cut-down spaces. In future, it is hoped to execute a planting plan considering the fire preventive function of trees on redevelopment of the park. 11 refs., 7 figs., 2 tabs.

  1. Influence of applied impulse voltage on creeping discharges along aerial insulated wire; Kaku zetsuen densen hyomen no enmen hoden ni okeru impulse den`atsu inka no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Nishi, T. [Toyama National College of Technology, Toyama (Japan); Hanaoka, R.; Miyamoto, T. [Kanazawa Institute of Technology, Ishikawa (Japan)

    1996-12-20

    In high voltage aerial distribution systems, insulated wires are supported by insulators. If overvoltages caused by lightning occur in the central line of an insulated wire, creeping discharges progress along the wire surface from the free end of the binding wire and bring about an accident such as punch- through breakdown, disconnection of wire. The clarification of breakdown phenomena in these insulation systems will contribute to the prevention of such accidents. These creeping discharges can take on complicated phenomena due to the change of the electric field intensity on the wire surface so that the potential of the central he of wire is changed by induced lightning. In this paper, we report the influence of the voltage change of the central line on lengths and aspects of creeping discharge when a standard impulse voltage is applied to the central line or binding wire. 5 refs., 9 figs., 1 tab.

  2. Relationship between discharge quantities and phase angle of applied voltage on treeing deterioration; Treeing rekka ni okeru hoden shoryo to inka den`atsu no soikaku tono kankei

    Energy Technology Data Exchange (ETDEWEB)

    Urano, K.; Osawa, K.; Kamikubo, H.; Ehara, Y.; Kishida, H.; Ito, T.; Hayami, T. [Musashi Institute of Technology, Tokyo (Japan)

    1998-11-01

    This research is carried out to analyze the treeing degradation phenomena with a needle shape void by a discharge magnitude and a discharge luminous quantity at each phase angle of an applied voltage. Discharge pulses and discharge luminous images are measured by original measurement system for measuring the discharge magnitude and the discharge luminous image according to several phase angle area of the applied voltage. Each phase angle area is named {phi}1-{phi}20 in order from the negative peak point to the next negative peak point of the applied voltage. The luminous image is digitized to the luminous quantity with a computer after experiment. In this study, we focused on the product of instantaneous value and dv/dt at the applied voltage. The results obtained are as follows. The discharge magnitude and the luminous quantity are the maximum at phase angle areas of {phi}7 and {phi}17. We define an effective instantaneous value that includes a voltage of residual electrical charge. The discharge magnitude closely correlates the effective instantaneous value times dv/dt. It is important to measure the discharge quantities at each phase angle area for analyzing the treeing degradation phenomena. 10 refs., 11 figs.

  3. Development of pure bending testing methods for advanced composite materials. Senshin fukugo zairyo no mage shikenho ni okeru jun mage hoshiki no kento

    Energy Technology Data Exchange (ETDEWEB)

    Iwai, H.; Uemura, M. (Nihon Univ., Tokyo (Japan). College of Industrial Technology); Uemura, S. (Fuji Heavy Industries Ltd., Tokyo (Japan))

    1994-04-15

    Advanced composite materials are strongly anisotropic and have high strength, high rigidity and many other fracture mechanisms, hence they show shortcomings such as generation of local fracture due to stress concentration at the point immediately below the loading point in case of application of the widely-used 3-point and 4-point bending tests, indicating their unsuitableness for the bending fracture test by the axial stress. In this article, bending testing methods of advanced composite materials, which can load the pure bending stress with no stress concentration, nor shearing stress component in the entire testing region, have been developed by test manufacturing a jig for pure bending. As a result of the experiment, no fracture due to local stress concentration like the 3-point and 4-point bending tests has occurred, the obtained bending strength has been more than 30% higher than that obtained by the 3-point and 4-point bending and a constant value has been obtained irrespective of its span. Also concerning the elastic coefficient obtained by this pure bending testing methods, the constant value has been obtained irrespective of span and plate thickness. Regarding the developed bending jigs, there are the sliding frame (SF) type and the rack and pinion (RP) type. For the SF and RP1 types, correction is required, but the RP2 type requires no correction. 3 refs., 15 figs.

  4. Effect of applied synthetic auxin on root growth in plantlet propagation by cuttage and tissue culture; Sashiki to soshiki baiyo ni okeru gosei auxin rui no shiyo koka

    Energy Technology Data Exchange (ETDEWEB)

    Shoji, K.; Yoshihara, T. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1996-12-01

    The effect of synthetic plant hormone 4-C1-IAA and TFIBA on root growth in plantlet propagation was clarified by the cuttage and the issue culture of strawberry seedling production. A periwinkle, vine, and azalea are the effect of 4-C1-IAA on root growth, and a promotion effect was recognized for rooting and root elongation. The concentration of 4-C1-IAA in which the growth promotion effect of a root most appears varies depending on the species of a plant. The concentration of a periwinkle was 20 ppm, and that of an azalea was 2000 ppm. The growth promotion effect of a root in 4-C1-IAA and TFIBA was compared with IBA for an azalea. The result showed that 4-C1-IAA is the same in the effect as IBA and that TFIBA is higher than for IBA. The growth of a vine`s terminal bud was promoted by the effect of TFIBA on root growth, and the callus occurring when IBA was treated was not formed. The rooting of a strawberry was promoted by the effect of TFIBA on root growth. The combined use of TFIBA and BA promotes the growth of a side bud and forms a multi-bud plant. However, rooting was inhibited. The callus caused by the effect of BA on root growth could be suppressed through the combined use with TFIBA. 6 refs., 7 figs., 2 tabs.

  5. Process of mixture formation of impinging spray on the wall in a hole type nozzle; Hole nozzle ni okeru hekimen shototsu funmu no hattatsu katei

    Energy Technology Data Exchange (ETDEWEB)

    Wakamatsu, T.; Tsunemoto, H.; Ishitani, H. [Kitami Institute of Technology, Hokkaido (Japan)

    1995-04-20

    In relation to mixture formation on a combustion chamber wall in a diesel engine, an experiment was conducted to have fuel spray that was injected from a hole type nozzle impinged on the wall. The appearance of the impinged spray was photographed, and so was the cross section in the vicinity of the wall to measure shapes, volume, and surface area of the impinged spray. The following results were obtained: spray impinged on the wall of a flat plate had the volume and surface area increased larger than in free spray; spray impinged on a wall with protrusion had the volume decreased as compared with the spray impinged on the flat plate, but the surface area increased; spray impinged on an inclined flat plate shows no large change in the volume and surface area after the impingement due to impinging angles, but shows change in the upstream and downstream distribution ratios; and in the case of spray impinged on a wall with lips, the spray center shifts to the lower wall because of the Coanda effect if the R radius at the lip root is large. 4 refs., 10 figs.

  6. Damage due to Hanshin-Awaji Earthquake and related subsurface conditions in Toyonaka City; Hanshin/Awaji Daishinsai ni okeru Toyonakashi no higai to jiban

    Energy Technology Data Exchange (ETDEWEB)

    Shinozaki, W.; Tanimura, K. [Construction Project Consultant Co. Ltd., Osaka (Japan); Takada, N. [Osaka City Univ., Osaka (Japan). Faculty of Engineering

    1996-02-01

    In spite of the fact that Toyonaka City in Osaka Prefecture is away from the seismic center by about 50 km, the number of houses completely or partially destroyed was as large as 10,000, and a maximum of about 3000 people had lived refuge lives. Toyonaka City topographically comprises an alluvial plain on the south of the Sone terraced cliff extending from east to west in the central part of the same city, and the undulating Senri hills on the north of the terraced cliff. In the substantially whole area of the alluvial plain, the wooden houses and some medium-storied ferro-concrete buildings were damaged, and, in the western inclined part of the hilly area, houses and housing lands were suffered from the earthquake. Underground buried facilities, such as waterworks and sewage were also damaged in substantially the same areas in which houses were destructed. This paper summarizes the relation between the distribution of seismic destruction and the ground and topographical conditions, correlating the results of the investigation into the earthquake disaster which was conducted by Toyonaka City with the ground diagram of the same city. It is considered that the damage by the earthquake was enlarged by not only the weak alluvial layers and loose fill-up ground but also the seismic motion amplified by the generally called `waterside focusing effect` of the hills extending toward the seismic center. 3 refs., 4 figs., 1 tab.

  7. Fiscal 1998 research report. Feasibility survey on offshore wind power generation in Japan; 1998 nendo chosa hokokusho. Nippon ni okeru yojo furyoku hatsuden no donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This survey studied the feasibility of large-scale offshore wind power generation in Japan. Attempt was also made on preparation of outline maps of offshore wind around Japan. The cost of future offshore wind power generation systems is roughly dependent on technical issues and environmental issues. As technical issues, 'installation site,' 'foundation,' 'system interconnection' and 'maintenance/management' were summarized based on applications in Europe. As a result, it was clarified that technical issues can be solved with existing technologies to a certain extent, however, those relate to economical problems closely. The previous environment impact assessments say that wind power generation has no problems on the environmental issues. As relatively strong wind coastal areas, the outline maps of offshore wind point out Western Hokkaido area, Japan Sea area of Tohoku district, Pacific ocean area of the central part of Honshu, Genkai Nada area, Western Kyushu area and Southwest islands area, and suggest that these areas are promising for offshore wind power generation. (NEDO)

  8. Detection of arcing ground fault location on a distribution network connected PV system; Hikarihatsuden renkei haidensen ni okeru koko chiryaku kukan no kenshutsuho

    Energy Technology Data Exchange (ETDEWEB)

    Sato, M.; Iwaya, K.; Morooka, Y. [Hachinohe Institute of Technology, Aomori (Japan)

    1996-10-27

    In the near future, it is supposed that a great number of small-scale distributed power sources, such as photovoltaic power generation for general houses, will be interconnected with the ungrounded neutral distribution system in Japan. When ground fault of commercial frequency once occurs, great damage is easily guessed. This paper discusses the effect of the ground fault on the ground phase current using a 6.6 kV high-voltage model system by considering the non-linear self-inductance in the line, and by considering the non-linear relation of arcing ground fault current frequency. In the present method, the remarkable difference of series resonance frequency determined by the inductance and earth capacity between the source side and load side is utilized for the detection of high-voltage arcing ground fault location. In this method, there are some cases in which the non-linear effect obtained by measuring the inductance of sound phase including the secondary winding of transformer can not be neglected. Especially, for the actual high-voltage system, it was shown that the frequency characteristics of transformer inductance for distribution should be theoretically derived in the frequency range between 2 kHz and 6 kHz. 2 refs., 5 figs., 1 tab.

  9. Nonlinear process generating Tollmien-Schlichting waves in a reattached boundary layer; Hakuri saifuchaku nagare ni okeru T-S hado no hisenkei reiki katei

    Energy Technology Data Exchange (ETDEWEB)

    Asai, M.; Aiba, K. [Tokyo Metropolitan Institute of Technology, Tokyo (Japan)

    1995-09-01

    Low-frequency Tollmien-Schlichting (T-S) waves may be thought generated as a result of high-frequency disturbance between two proximity frequency modes grown unstably in a separation shear layer causing secondary nonlinear interference to occur. This fact has been verified by a numerical simulation. A non-compression Navier-Stokes equation was used for the fundamental equation, a tertiary windward difference for the convection term, and a secondary central difference for other differential calculus. The Reynolds number was 200, and the disturbance was introduced by applying `v` variation continuously on the wall face. Non-introduction of the disturbance results in a steady flow. Disturbance frequencies of 0.15 and 0.20 were selected as disturbance frequencies from the relationship between the spatial amplification and the frequency dependency. The structure of the excited disturbance agreed with the intrinsic mode. The difference mode due to nonlinear interference grows as the basic mode was amplified. The basic mode decays sharply in the boundary layer after reattachment, while the difference mode decays slowly. Distribution of the difference mode is a distribution of viscous T-S waves, which may be converted into the intrinsic mode. 8 refs., 7 figs.

  10. Photo-irradiation effects on GaAs atomic layer epitaxial growth. GaAs no genshiso epitaxial seicho ni okeru hikari reiki koka

    Energy Technology Data Exchange (ETDEWEB)

    Mashita, M.; Kawakyu, Y.; Sasaki, M.; Ishikawa, H. (Toshiba Corp., Kawasaki (Japan). Research and Development Center)

    1990-08-10

    Single atomic layer epitaxy (ALE) aims at controlling a growing film at a precision of single molecular layer. In this article, it is reported that the growth temperature range of ALE was expanded by the vertical irradiation of KrF exima laser (248 nm) onto the substrate for the ALE growth of GaAs using the metalorganic chemical vapor deposition (MOCVD) method. Thanks for the results of the above experiment, it was demonstrated that the irradiation effect was not thermal, but photochemical. In addition, this article studies the possibility of adsorption layer irradiation and surface irradiation as the photo-irradiation mechanism, and points out that coexistence of both irradiation mechanisms can be considered and, in case of exima laser, strong possibility of direct irradiation of the adsorption layer because of its high power density. Hereinafter, by using both optical growth ALE and thermal growth ALE jointly, the degree of freedom of combination of hetero ALE increases and its application to various material systems becomes possible. 16 refs., 6 figs.

  11. Vortex-induced vibrations of circular cylinder in cross flow at supercritical Reynolds numbers; Chorinkai Reynolds su ryoiki ni okeru enchu no uzu reiki shindo

    Energy Technology Data Exchange (ETDEWEB)

    Kawamura, T.; Nakao, T.; Takahashi, M.; Hayashi, M.; Goto, N. [Hitachi, Ltd., Tokyo (Japan)

    1999-07-25

    Vortex-induced vibrations were measured for a circular cylinder subjected to a water cross flow at supercritical Reynolds numbers for a wide range of reduced velocities. Turbulence intensities were changed from 1% to 13% in order to investigate the effect of the Strouhal number on the region of synchronization by symmetrical and Karman vortex shedding. The reduced damping of the test cylinder was about 0.1 in water. The surface roughness of the cylinder was a mirror-polished surface. Strouhal number decreased from about 0.48 to 0.29 with increasing turbulence intensity. Synchronized vibrations were observed even at supercritical Reynolds numbers where fluctuating fluid force was small. Reduced velocities at which drag and lift direction lock-in by Karman vortex shedding were initiated decreased with increasing Strouhal number. When Strouhal number was about 0.29, the self-excited vibration in drag direction by symmetrical vortex shedding began at which the frequency ratio of Karman vortex shedding frequency to the natural frequency of cylinder was 0.32. (author)

  12. Efficient calculation of potential distribution in two-layer earth; Niso kozo daichikei ni okeru denki tansa no tame no koritsuteki den`i keisan shuho

    Energy Technology Data Exchange (ETDEWEB)

    Kataoka, M.; Okamoto, Y. [Chiba Institute of Technology, Chiba (Japan); Endo, M.; Noguchi, K. [Waseda University, Tokyo (Japan); Teramachi, Y.; Akabane, H. [University of Industrial Technology, Kanagawa (Japan); Agu, M. [Ibaraki University, Ibaraki (Japan)

    1997-05-27

    An efficient calculation method of potential distribution in the presence of an embedded body in multi-layer earth has been proposed by expanding the method of image with a consideration of multiple reflection between the ground surface and each underground boundary. For this method, when solving boundary integral equation with the potential of embedded body surface as only one unknown, i.e., when obtaining discretization equation, ordinary boundary element program developed for analyzing the finite closed region can be used. As an example, numerical calculation was conducted for the two-layer earth. The analysis expression of potential distribution in the case of the certain embedded body in two-layer earth has never published. Accordingly, the calculated results were compared with those by the integral equation method. As a result, it was concluded that the primary potential obtained from the present method agreed well with that obtained from the integral equation method. However, there was a disregarded difference in the secondary potential. For confirming the effectiveness, it was necessary to compare with another numerical calculation method, such as finite element method. 5 refs., 5 figs.

  13. Food and chemical industry. Concentration and drying in the manufacture of instant coffee; Shokuhinn to kagaku kogaku. Insutanto coffee no seizo ni okeru noshuku to kanso

    Energy Technology Data Exchange (ETDEWEB)

    Imura, N. [Tokyo Univ. (Japan)

    1997-05-05

    In this paper, the history and manufacturing method of instant coffee are introduced emphasizing the concentration and drying technology in the manufacturing process of instant coffee. Instant coffee can be roughly classified into three kinds as those respectively made from freeze drying, spray drying and the agglomeration after drying, which are different in shapes and properties from each other. For obtaining quality instant coffee remaining more aroma of coffee extract, it is extremely effective and important to increase the concentration of solid component of coffee in extract simultaneously with the setting of conditions of drying process. Thermal concentration, freeze concentration and membrane concentration are used in the concentration of coffee. Spray drying and freeze drying are executed to remove water from concentrated coffee liquid as the finishing step of the manufacture of instant coffee. 3 refs., 4 figs.

  14. Water management and regional environment in the Hetao irrigation area, Inner Mongolia, China; Uchimoko kagaikanku ni okeru mizu kanri to chiiki kankyo

    Energy Technology Data Exchange (ETDEWEB)

    Ji, B.; Akae, T.; Nagahori, K. [Okayama Univ. (Japan)] Otsuki, K. [Tottori Univ. (Japan)

    1998-08-01

    The history of the Hetao irrigation area can be said as the history of war in arid and semi-arid areas fought between human activity and environmental harmony. Balance of the natural water circulation is damaged as a result of agricultural production by irrigation in the Hetao irrigation area, and salt damage occurred to worsen the environment of the area. Drainage facilities are introduced as the improvement measures, but it is not easy to restore the once-damaged natural environment. Increase of salt damaged land in the area is restrained by the drainage facilities, but the incoming of salt exceeds the outgoing. The scale of the present drainage facilities is not satisfactory for restoring the salt damaged land. The salt content of the water taken in the Hetao irrigation area from the Yellow River is increasing every year influenced by the drainage from the upstream areas of the Hetao irrigation area. At the same time, untreated waste water is drained in the Yellow River. As a result, the present drainage facilities work to mitigate salt drainage in the area, but help to worsen the salt damage in downstream areas. 5 refs., 3 figs., 3 tabs.

  15. Experimental study of high-speed counter-rotation propeller on low speed wind range; Dojiku hantengata kosoku propeller no teisokuiki ni okeru fudo jikken

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Collaborative research was conducted by National Aerospace Laboratory and Japan Aircraft Development Company in the period of fiscal 1988-1992 into methods for testing aircraft with advanced propeller in low-speed wind tunnel. The propulsion efficiency of the currently available high-bypass turbofan engine is approximately 60% in the vicinity of Mach number 0.85. Propeller-driven aircraft, whose propulsion efficiency is as high as 80% in the low Mach number domain, are scarcely in practical use in the domain of Mach number 0.75 or higher. There are studies reported abroad as well as in Japan for the propeller-driven aircraft to enjoy higher propeller propulsion efficiency even in the vicinity of Mach number 0.8 by modifying the propeller diameter, number of blades, and blade sections, etc. This paper describes the experimental research into the high-speed counter-rotation propeller. A counter-rotation propeller 0.3m in diameter and provided with coaxially arranged 8times2 SR-2 blades is evaluated for pitch angles during the takeoff and landing modes, for thrust characteristics at the pitch angle for the cruising mode, and for propeller backwash and noise. 15 refs., 72 figs., 9 tabs.

  16. CSAMT application in deep structural exploration at Akinomiya. Shingogen seigyo chijiki chidenryuho (CSAMT ho) no tekiyo. Akitaken Akinomiya chiiki ni okeru chinetsugen chosa

    Energy Technology Data Exchange (ETDEWEB)

    Motojima, Mutsumi; Kusunoki, Ken' ichiro.

    1988-11-01

    The controlled source antifrequency magnetotelluric method (CSAMT method) was applied to the site exploration at Akinomiya in Akita Prefecture as a part of research to improve geothermal exploration technique so as to utilize geothermal energy. CSAMT method is one of the measurement of underground resistivity with the equipment artificially transmitting electromagnetic waves of different frequencies to improve the accuracy of the exploration. Underground resistivity structure obtained form profile analysis for measured apparent resistivity indicated high resistivity zone corresponding to the lower basement rocks area and the boundary agreed with existing geological section. On the other hand, horizontal distribution map of apparent resistivity zone overlaps on the existing area of hot spring. CSAMT method is thought effective to survey the geological structure and to explore geothermal resources from the researched results. This method may be useful to select the site for underground structures along with the development of geothermal energy. 8 refs., 22 figs., 1 tab.

  17. Wind energy technology : from the past to the future; 20 seiki ni okeru furyoku riyo gijutsu no henkan. Furyoku hatsuden : kako kara mirai e

    Energy Technology Data Exchange (ETDEWEB)

    Ushiyama, I. [Ashikaga Institute of Technology, Tochigi (Japan)

    2000-01-20

    Windmills are one of the oldest prime movers and have been used for more than 700 years in Europe. The transition from low speed windmills for grain grinding and water pumping to high speed wind turbines for electric power generation had occurred at first, reviews the windmill technologies and the researchers before 20{sup th} century. Then describes the back ground of how the wind power generator has existed and how the four pioneers developed their wind power generator. The historical developments of windmills to wind turbines in this century are studied focusing mainly on Danish activities. Then, the effort of the development of large wind turbine such as Smith-Putnum's first MW machine in U.S.A. and other mammoth machine concept are introduced. The new concept machines such as Savonius and Darrieus wind turbines in 1920s to 1930s are also explained. Finally, the novel technologies of wind turbine covering larger machines, variable speed generators, special wing sections for wind turbines, theoretical analysis method of wind turbine performance, offshore wind turbines, and wind turbine control technologies are stated. (author)

  18. Temperature dynamic models of heat exchanger for photosensitive material coating and drying processes; Kanko zairyo tofu kanso process ni okeru kucho system no ondo doteki model

    Energy Technology Data Exchange (ETDEWEB)

    Kido, K.; Sato, N.; Shimoji, M. [Konica Co. Ltd., Tokyo (Japan); Nakanishi, E. [Kobe University, Kobe (Japan). Faculty of Engineering

    1996-01-20

    Nonlinear and linear temperature dynamic models of a heat exchanger were investigated for air conditioning control of coating and drying processes for photosensitive materials. The nonlinear model was derived from heat balance based on the assumption of lumped parameter system that the heat exchanger is divided into small parts in the direction of flow (divided cell model). In each part, the temperature of the heating fluid, heated fluid and heat transfer tube with fin are assumed to be uniform. Parameters involved in this model were estimated from experimental data of the step response characteristics of temperature. The linear model is obtained by linearizing this nonlinear model. It was confirmed that the dynamic behavior of temperature can be successfully expressed by both nonlinear and linear models. Both models are considered to be utilizable for process analysis and control system design of the air conditioning system under consideration. 1 ref., 13 figs., 2 tabs.

  19. Temperature control of a heat exchanger for the photosensitive materials coating and drying process; Kanko zairyo tofu kanso purosesu ni okeru kucho system no ondo seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Kido, K.; Sato, N.; Shimoji, M. [Konica Co. Ltd., Tokyo (Japan). Production Engineering Center; Nakanishi, E. [Kansai Univ., Suita, Osaka (Japan). Faculty of Engineering

    1997-11-01

    A feedforward/feedback control system was developed to maintain the temperature profile of air in an air conditioning system for photosensitive material coating and drying. The feedforward control was attained based on a heat exchanger dynamic model using the flow rate of hot water as the manipulated variable and the air temperature as the controlled variable, while feedback control was performed by means of optimum control theory based on a linearized heat exchanger dynamic model. To evaluate the performance of the control system developed in this study, simulation and experimental studies were carried out where a stepwise change of set values is performed in order to maintain uniform production quality for each product grade. It is shown that the control system under consideration successfully controls air temperature in an air conditioning system for photosensitive material coating and drying. 4 refs., 7 figs.

  20. Independent activity plan for reducing the emission of sulfur hexafluoride (SF6) in the electric industry; Denki jigyo ni okeru rokufukka io (SF6) haishutsu yokusei ni kansuru jishu kodo keikaku ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-11-01

    This paper describes the reduction of SF6 emission in the electric industry. The weight and size of equipment can be reduced by SF6, which is widely used for electric equipment such as gas circuit breakers and gas insulation switches due to its safety. The gas circuit breaker occupies over 70% of circuit breakers above 66 kV-class ones. The gas insulation switches are employed for all of 275 kV-class substations at 13 locations in central Tokyo. The site area for constructing substations can be drastically reduced, and underground substations can be constructed in urban areas. On the other hand, it has been recently pointed out that SF6 gas is one of the greenhouse gases, and SF6 was added as an emission reduction gas by COP3. Since an effective alternative insulation gas of SF6 has not been found out, the suppression of its emission in the air is planned as an activity for reducing the SF6 emission. For the protection of leakage during inspection of equipment, the present emission amount 40% is to be reduced down to 3%. For the recovery from the abandoned equipment, the emission amount is to be reduced up to 1%. Systems for reusing and managing SF6 are to be independently enhanced. 1 fig.

  1. Relationship between the electric resistivity and the rain fall in discontinuity zone of rock slope by the continuous measurement; Renzoku tokei ni yoru ganban shamen no furenzokutaibu ni okeru mikake hiteiko henka to kou tono kankei ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Kusumi, H.; Nishida, K. [Kansai University, Osaka (Japan). Faculty of Engineering; Nakamura, M. [Newjec Inc., Osaka (Japan)

    1996-10-01

    The relationship between change in resistivity and rainfall was studied by continuously measuring resistivities of fracture zone and stratum boundary along the measuring line of 95m long from the top to bottom of rock slope. The measurement field was located on a hill of 150-200m high at the northern part of Arima-Takatsuki tectonic line. Electrodes of 30m in maximum measuring depth were arranged at 289 points by dipole-dipole method. Resistivity was continuously measured at time intervals of 6 hours. Apparent resistivity was hardly affected by rainfall at points with less infiltration of stormwater from the ground surface, while it decreased by rainfall at points on fracture zone, stratum boundary or bleeding channel. The change rate of apparent resistivity could be approximated with the exponential function of rainfall. In such case, the apparent resistivity under most dried condition at the concerned point should be used as reference maximum apparent resistivity. The change rate of apparent resistivity due to rainfall in fracture zone reflects infiltration of stormwater, suggesting to be useful for disaster prevention of slopes. 5 refs., 6 figs.

  2. Investigation studies on renewable energy resources in Asia. Wind and solar energies in Vietnam, Malaysia; Asia ni okeru saiseigata shizen energy kaihatsu shuho to fusonryo ni kansuru chosa kenkyu. Vietnam oyobi Malaysia ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, Y.; Takada, M.; Ono, H. [Mie University, Mie (Japan). Faculty of Engineering; Loc, N.; Khan, N. [Hanoi Institute of Technology (Viet Nam); Bardaie, M.; Ismail, W.; Yahya, A. [University of Pertanian (Malaysia)

    1996-06-01

    Wind and solar energy in Vietnam and wind energy in Malaysia were calculated for their amounts available in respective areas based on meteorological data. Annual average wind velocity 30 m above the ground in Vietnam is 4 to 5 m/s in many points of coastal areas, and a little lower in the inland. On the other hand, wind velocity may exceed 9 m/s in sea areas (on islands). According to the result of a trial calculation using data derived from all the observation points, 10-kW generators and 20-kW generators, if installed, may have their operation factors exceed 20% in many points. Even compared with Cape Tappi, Aomori Prefecture, Japan, where the operation factor is 18.7%, these points in Vietnam are suitable for wind power generation. Average wind velocity 30 m above the ground in Malaysia is only about 4 m/s even at high altitude. However, wind with velocity from 7 to 9 m/s may appear depending on districts. If 10-kW and 20-kW generators are installed, the operation factors in Mersing and Langkawi would exceed 30% and 20%, respectively, where wind has sufficient value of utilization. The operation factor may be low in areas other than the above districts. However, since the observation data were those taken in urban areas, collection of further detailed data is necessary. 4 refs., 7 figs., 3 tabs.

  3. Numerical method to calculate flow-induced vibration in turbulent flow. 3rd Report. Analysis of vortex-induced vibration in an array of elastically supported tubes; Ranryuba ni okeru ryutai kozotai rensei shindo kaiseki shuho no kaihatsu. 3. Kangun ni okeru uzu reiki shindo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Sadaoka, N.; Umegaki, K. [Hitachi, Ltd., Tokyo (Japan)

    1996-01-25

    A vortex-induced vibration of an array of elastically supported tubes is simulated in two-dimension by using a flow-induced vibration analysis program, which was developed in order to evaluate flow-induced vibration in various components such as heat exchangers. From a comparison of calculated results and experimental data, the following points are observed. (1) For the calculated results in a 5 {times} 5 square array, the flow pattern surrounding the first-row tubes is markedly different from that observed in the second-row or third-row tubes. This flow pattern is the same as that obtained from the experiment. (2) All tubes begin to oscillate due to unsteady fluid force and the oscillating mode is different for each row of tubes. These oscillation patterns show the same tendency in the experiments and it is concluded that the developed method can simulate vortex-induced vibration in an array of elastically supported tubes. 19 refs., 10 figs., 1 tab.

  4. Study of solute incorporation into ice-layer on freeze concentration with ice-lining; Ice lining toketsu noshukuho ni okeru hyosho sochu eno yoshitsu torikomi ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Yamazaki, Y.; Shinozaki, K. [Fujisawa Pharmaceutical Co. Ltd., Osaka (Japan); Hirata, Y. [Osaka University, Osaka (Japan)

    1997-07-10

    The mechanism of solute incorporation into an ice-layer in freeze concentration with ice-lining was studied by changing the impeller speed N and the difference between the brine temperature and the freezing point of the feed solution {Delta}T in 10 kg/m{sup 3} CCNa solution. The effect of N on the apparent partition coefficient of the solute K, is more serious than that of {Delta}T. The growth rate of the ice layer is 10{sup -7} - 10{sup -6}m/s under the condition of {Delta}T=2.8 - 7.9degC and N = 20-400 min{sup -1}. The growth rate had a little effect on solute incorporation into the ice-layer. K values depended on the surface condition of the ice layer, which is effected by the mixing speed of the impeller. The ice layer formed at low mixing speed has a complex rough shape, and has much solute because of adhesion to a large surface area. Therefore, it is recommended that freeze concentration is performed by making an ice layer with smooth surface at high mixing speed. 9 refs., 6 figs.

  5. Formation of flow interface of resin around spear implemented in hot-runner varied by heating densities; Hot runner ni okeru spear hatsunetsu mitsudo ni yoru jushi kyokaiso keisei

    Energy Technology Data Exchange (ETDEWEB)

    Yokoyama, T. [Yamagata University, Yamagata (Japan). FAculty of Engineering; Sato, A. [Fuji Xerox Co. Ltd., Tokyo (Japan); Ito, C. [Seiki Corp., Yamagata (Japan); Yoshida, T. [Toppan Lebel, Tokyo (Japan)

    1999-04-25

    The SPEAR-SYSTEM, one of the Hot-Runner molding, is rational and economical thermal valve-gate system. A resin around the SPEAR which is heating object like a spear, sorts into the solidification-layer and flow-layer. The former takes important role of insulator, then prevents a resin leak at molding. Though location of the interface of solidification varies due to flow and thermal condition, quantitative treatment is not applied yet. Engineers have just depended on their experiences for thermal design as to Hot-Runner System. In this paper we have measured temperature field inside the Runner-bush and location of the interface, on the other hand established a numerical code and compared both values. As a result, we have confirmed agreements between the experiment and the numerical. Therefore we could forecast what happens in flow and temperature field around Spear under a variety of conditions. (author)

  6. Research on energy conservation in petrochemical and steelmaking industries in a developing country (India); Hatten tojokoku (Indo) ni okeru sekiyu kagaku kogyo tekkogyo no energy shohi koritsuka ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Current state of energy conservation in petrochemical and steelmaking industries in India was surveyed to estimate energy consumption and demand, and discuss possible international cooperation. Recently India has grown rapidly, and its growth rate of energy consumption is higher than a rise in GDP. In order to examine the current state of energy conservation in India, major energy consumption levels in India was surveyed together with production outputs of steelmaking, oil refining and petrochemical industries. Energy consumption and the potential of current energy-saving programs were also surveyed in modern factories. As a result, for energy conservation in petrochemical and steelmaking industries in India, the following were pointed out: improvement of operation conditions in current facilities, improvement of management systems in current facilities such as introduction of computers, and modification of production processes. Improvement of energy efficiency by introducing advanced technologies from developed countries such as Japan was essential. 37 figs., 45 tabs.

  7. Effect of fluoride ion on the pitting corrosion of type 304 stainless steel in neutral NaCl solution. Chusei NaCl suiyoekichu ni okeru SUS 304 ko no koshoku ni oyobosu F[sup -] no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Yamazaki, O. (Nippon Kinzoku Co. Ltd., Tokyo (Japan). Technical Research and Development Lab.)

    1994-05-15

    Anode polarization measurement is performed in mixed solution of NaCl and NaF using SUS 304 steel to investigate whether F[sup -] promotes or inhibits pitting corrosion. Pitting corrosion does not occur in the solution of NaF only, but passive state is broken above a certain critical potential, resulting in overall dissolution. When anode polarization measurement is made in a solution of fixed concentration NaCl added with NaF, pitting corrosion is inhibited at a certain critical concentration. F[sup -] has no effect on corrosion potential in the solution up to this critical concentration. Overall dissolution occurs in the solution with higher concentration than the critical concentration, the current value at that time agrees with that in the solution of NaF alone, and no effect of Cl[sup -] is shown. The concentration range where pitting corrosion occurs and that where overall dissolution occurs are divided by a straight line when they are expressed by logarithm of NaCl and NaF concentrations. The equation of the straight line which expresses this critical concentration is shown. 21 refs., 9 figs., 1 tab.

  8. Bubble motion in liquid nitrogen under a non-uniform electric field in a microgravity environment; Bisho juryoku kankyoka ni okeru ekitai chissochu kiho no denkai ni yoru undo

    Energy Technology Data Exchange (ETDEWEB)

    Suda, Y.; Muto, K.; Sakai, Y. [Hokkaido Univ., Sapporo (Japan); Honma, N. [Hokkaido Electric Power Co., Inc., Sapporo (Japan)

    1997-10-20

    The motion of bubbles in liquid nitrogen (LN2) in a non-uniform electric field are observed in a microgravity environment just after release from the terrestrial gravity. The dynamic behavior of the bubbles is analyzed considering the electro-hydrodynamics and thermodynamics, and is explained consistently by a theory including these forces. The shrink of the bubbles in supercooled LN2 is discussed. 15 refs., 8 figs.

  9. Researches regarding a constructing problem of a PV system. Part 1. Conscious investigation by means of a questionnaire survey; Taiyoko hatsuden system ni okeru kenchikuteki shomondai no kenkyu. 1. Anketo chosa ni yoru ishiki chosa

    Energy Technology Data Exchange (ETDEWEB)

    Nakajima, Y.; Yamazaki, R.; Kuroki, T. [Kogakuin University, Tokyo (Japan)

    1996-10-27

    The installation and introduction of photovoltaic power generation systems (PVS) in buildings are growingly expected in the construction field from now, coupled with the marketing of a solar cell module as a product for a construction material in the form of an external wall or a roof material for example. For this purpose, it is necessary at first to summarize problems that may arise at the time of or after the installation of PVS as a product. This paper examines an opinion poll, degree of recognition, current problems, etc., of PVS as a result of a questionnaire survey given to engineers and architects engaged in the actual construction business. The degree of recognition and interest was very high. Consultation or request for PVS installation was much more than predicted in numbers. Roughly 50% of the respondents reacted positively for the future installation request of PVS and, combined with the respondents who answered to look into the installation tentatively, not less than 90% were of a forward-looking opinion. The 85% of the respondents was not aware of the monitor business system for residential PVS. Further, the survey clearly brought out the importance of cost problems. 1 ref., 11 figs., 3 tabs.

  10. Study on heat collector of the solar system utilizing outdoor air. Experimental results in cases of cold and warm regions; Gaiki donyushiki solar system no shunetsubu ni kansuru kenkyu. Kanreichi to ondanchi ni okeru shunetsu jikken to kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Komano, S.; Ebara, Y. [OM Solar Association, Shizuoka (Japan); Wada, H. [Wada Building Constructors Co. Ltd., Hokkaido (Japan)

    1996-10-27

    An experiment on heat collection was made in the heat collector of a solar system utilizing outdoor air in cold and warm regions. In this system, outdoor air is heated by the air circulation layer on the roof exposed to solar radiation. The heated air is supplied to the object space for heating and ventilation. In the experiment in a cold region, the heat collection characteristics can be adjusted by putting a baffle plate in the air duct according to the experiment of a glass heat collector. The heat collecting air layer on only the iron roof may leak or freeze in the region subject to coldness or heavy snowfall. Therefore, preheat forms the space of a garret, and the preheat temperature comparatively becomes low. The data in which the heat collection characteristics can be adjusted using only a glass heat collector is required corresponding to the regional situation. In the experiment in a warm region, an experiment was made inclusive of the preheat for which outdoor air is absorbed at the eaves. As a result, the heat collection characteristics of preheat were improved. Moreover, a heat collection temperature of about 60{degree}C was obtained on the heat collection surface including the preheat. 1 ref., 12 figs., 3 tabs.

  11. Research on passive solar energy application in Bolivia. Part 2. Development of weather data for air conditioning load calculation; Bolivia ni okeru passive ho no riyo kanosei ni kansuru kenkyu. 2. Kukan fuka keisan`yo kiso data no sakusei

    Energy Technology Data Exchange (ETDEWEB)

    Ishizuka, O.; Kaihara, K.; Zhang, Q. [Kumamoto University, Kumamoto (Japan)

    1994-12-08

    To know the applicability of passive solar energy in Bolivia, weather data were prepared for the air conditioning load calculation. As a representative city in the plateau, foot and plain, El Alto, Cochabamba and Santa Cruz were selected, respectively. Based on the observation data in the airport`s weather stations, data were prepared on the atmospheric temperature, humidity, wind direction, wind velocity and cloudiness. Because there existed no data on the quantity of solar radiation, its daily integrated quantity was calculated by regression from the daily mean cloudiness recorded in the data which were collected in 1978 by the meteorological observatories belonging to both Ministry of Transport, and Ministry of Posts and Telecommunications. More adaptable than the linear regression formula, the quadratic one gave correlation coefficients convergent in the region from 0.5 to 0.9 in most of the months. The daily integrated quantity of solar radiation was then divided by Collares model into its time-by-time quantities, which were further divided by Udagawa method into both their direct component and diffused component. Though the summer cloudiness is high in both El Alto and Cochabamba, the quantity of solar radiation is larger than that of the winter, which is judged attributable to the high solar angle of elevation. The wind is strong in El Alto. 5 refs., 7 figs., 3 tabs.

  12. On the calculation of scattered fields by 3-D structure in the time-domain electromagnetic (TDEM) method; Jikan ryoiki denjiho ni okeru sanjigen kozo kara no sanranba no keisan ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Murakami, Y. [Geological Survey of Japan, Tsukuba (Japan); Saito, A.; Oya, T. [Mitsui Mineral Development Engineering Co. Ltd., Tokyo (Japan)

    1996-10-01

    This paper describes the calculation method of 3-D underground structures in TDME method which measures only field components. Recently, FDTD method was developed as calculation method in time domain difference calculus, and the forward analysis accuracy of 3-D fields was rapidly improved. The survey results using a large-scale loop (600m{times}360m) were numerically analyzed by FDTD method. 16 measuring lines were prepared in both X and Y directions, and measuring points were prepared on intersection points of the measuring lines. Since signal current is staircase one, step and impulse responses of the ground were determined by calculating magnetic field and its time differentiation. The rectangular body (120m{times}120m{times}100m) of 0.2S/m in conductivity (5 ohm m in resistivity) was installed 160m under the ground as 3-D resistivity anomaly. The ground of 0.01S/m (100 ohm m) was assumed. Time variation in horizontal magnetic field vector plot of impulse responses of the uniform ground could be observed. The position of the resistivity anomaly could be also determined from spacial differentiation of magnetic field of grid pattern measuring points. 1 ref., 6 figs.

  13. Electromagnetic survey (TEM method) in Teradomari and examination of resistivity structure to be based on near surface information; Niigataken Teradomarimachi ni okeru denji tansa kekka (TEM ho) no doshitsu joho ni yoru kento

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, H.; Mitsuhata, Y.; Matsuo, K.; Tanaka, H. [Japan National Oil Corp., Tokyo (Japan). Technology Research Center; Wada, K. [Mitsui Mineral Development Engineering Co. Ltd., Tokyo (Japan)

    1996-10-01

    TEM method was applied to estimate soil structure from resistivity change of underground water saturated stratum featured by slow S wave and fast P wave over 1500m/s. Vertical magnetic field was measured by underlaying a transmission loop of 60m{times}60m around a measuring point in Teradomari, Niigata prefecture, and by installing a magnetic sensor at the measuring point. From comparison of a soil profile with the resistivity profile obtained by TEM data, the former well consisted with the latter. The surface low resistivity stratum corresponded to alluvium from comparison of it with soil and logging data. This alluvium base with fast P wave over 1500m/s satisfied the condition of optimum blasting depth because of a saturated stratum in the surface base. The resistivity structure was related to a saturated stratum. Sand bed was thick at the interface between alluvium low ground and hill area, and from the analytical result, the depth of sand bed showing high resistivity was more shallow than that of the alluvium base, pointing out necessary notice in interpretation. Resistivity survey is promising as simple method for optimum blasting depth. 4 refs., 6 figs., 1 tab.

  14. Borehole geophysics for delineating the geological structure in the Sakonishi prospect, the Hida area, Japan; Hida chiiki Sako nishi chiku ni okeru boring ko riyo butsuri tansa ni yoru chishitsu kozo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Katayama, H.; Hishida, H.; Yoshioka, K. [Metal Mining Agency of Japan, Tokyo (Japan)

    1997-05-27

    In order to discuss effectiveness of physical exploration in the Sakonishi prospect in the Hida area, physical exploration was carried out by utilizing bored wells. This area contains the Kamioka mine, one of the major base metal mines in Japan, where electrical exploration has been attempted several times in the past. No effective results have been obtained, however, because specific resistance contrast between mine beds and base rocks is too small, and the topography is too steep making site workability inferior. As part of the investigations on geological structures over wide areas, electrical logging (specific resistance and natural potential) was performed in fiscal 1995 and 1996 by utilizing the boreholes. Induced polarization logging was also conducted on the same boreholes. A traverse line on the ground with a length of 600 m and boreholes were used to execute specific resistance tomography. Clear extraction was possible on a fault structure which is thought related with limestone distribution and mine bed creation. However, it was not possible to identify upward continuity of zinc ores expected in the exploration. Because of not large a specific resistance contrast between zinc ores and base rocks, it is difficult to find mine bed locations only from the information on the specific resistance. 5 refs., 5 figs., 1 tab.

  15. Research and survey report of FY 1997 on the CO2 balance for high-temperature CO2 fixation and utilization technology; 1997 nendo chosa hokokusho (nisanka tanso koon bunri gijutsu ni okeru CO2 balance ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The purpose of this research is to clarify the application condition and effectiveness of high-temperature CO2 fixation and utilization technology. To evaluate the present process, it was compared with others, such as separation using a polymer membrane, physico-chemical absorption process, adsorption process, hydrogen contact reduction process, and biological fixation. The development trends of absorption, membrane, adsorption, and cryogenic separation were investigated. The questionnaire was carried out about the separation technologies which are in the stage of performance test using actual gas, to arrange and compare the data and information. The current trends of chemical and biological CO2 fixation and utilization technology were also investigated for arranging the subjects. High-temperature CO2 disposal by the carbonation in concrete waste has been studied, to clarify its application conditions and effectiveness. In order to compare the separation technologies, treatment processes of CO2 in the exhaust gas from boilers of LNG power generation and coal fired power generation were simulated. These processes were simulated by ASPEN PLUS for the modeling. Trends of application of ASPEN PLUS and collection of information were surveyed by participating in the ASPEN WORLD. 103 refs., 51 figs., 55 tabs.

  16. Air cleaning in clean rooms. Super-cleaning of mini-environments by UV/photoelectron method; Clean room ni okeru kuki seijo. UV/hikari denshiho ni yoru kyokusho kukan no cho clean ka

    Energy Technology Data Exchange (ETDEWEB)

    Fujii, T.; Suzuki, T. [Ebara Research Co. Ltd., Kanagawa (Japan); Sakamoto, K. [Saitama Univearsity, Saitama (Japan); Yokoyama, Ss.; Hirose, M. [Hiroshima University, Hiroshima (Japan)

    2000-04-20

    Prevention of wafer surface contamination is an important issue in semiconductor manufacturing as such contamination decreases LSI productivity. Although particulate contamination in work rooms is being reduced by newer cleanroom techniques, there are still sources of particulate contaminants, such as wafer delivering systems, wafer stockers, and load-lock chambers. Not only fine particles but also gaseous contaminants need to be controlled. The following introduces an outlook on various methods of removing such particle and gaseous contaminants. (author)

  17. Study of a fuel injection quantity sensor in diesel engine. Part 3. Experimental evaluation of the improved type micro turbine sensor; Diesel kikan ni okeru nenryo funsharyo sensor no kenkyu. 3. Funsharyo keisoku no seido kojo ni kansuru jikken hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Maehara, H.; Iwasaki, T.; Kobayashi, T. [Zexel Corp., Tokyo (Japan)

    1997-10-01

    A Micro Turbine Sensor has been developed to measure fuel injection quantity and injection rate. Previous reports described results of experiments on the MTS which were carried out under steady and unsteady flow conditions. The MTS has been improved in shape of a holder tip and a detecting procedure for rotating speed of a turbine. As a result revolution speed of the turbine increased 18% over the conventional type holder under steady flow condition. Furthermore the measurement resolution of the MTS came up to about 2(mm{sup 3}/pulse) at 20(mm{sup 3}/stroke) under intermittent spray conditions using fuel injection pump. 11 refs., 11 figs., 1 tab.

  18. Study of the oil flow and the bearing temperature in engine. Part 3. Influence of the bearing designs; Engine ni okeru jikuuke yuryo oyobi jikuuke ondo ni kansuru ichikosatsu. 3. Jikuuke sekkei yoso no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, K.; Kawai, K.; Sasaki, S. [Taiho Kogyo Co. Ltd., Aichi (Japan)

    1997-10-01

    It is necessary to find the bearing design so that the bearing temperature drops most efficiently by making the proper oil flow. We measured the oil flow and the bearing temperature using the narrow width bearing the bearing with small oil relief , the bearing with shallow circumferential microgrooves (the microgrooved bearing), the narrow width bearing with microgrooves. And further, we measured the variation of the oil flow every 5-15deg crank angle and searched for the efficient oil flow. As the result the bearing temperature using the microgrooved bearing dropped most efficiently. 3 refs., 13 figs., 5 tabs.

  19. Softening and hardening by. gamma. yields. epsilon. martensitic transformation during deformation in high Mn steels. Ko Mn tetsu gokin ni okeru. gamma. yields. epsilon. martensite hentai ni yoru nanka to koka

    Energy Technology Data Exchange (ETDEWEB)

    Tomota, Y.; Ryufuku, S.; Piao, M. (Ibaraki University, Ibaraki (Japan). Faculty of Engineering)

    1991-01-15

    In high Mn steel, martensitic transformation of gamma to epsilon occurs under the ordinary pressure. Its application comprises utilization of its configuration memory properties and high work hardening characteristics. The present report studied, by using Fe-Mn type alloy, added with Si or Co, the influence of martensitic transformation of gamma to epsilon on the deformation behavior. Tensile test, 2mm/min in speed, being made on molten/cast alloy ingot, thermally treated as specified, epsilon was quantitatively analyzed by X-ray diffraction. The above test/analysis pointed out many notes in result and knowledge, as follows among others: The addition with Si or Co, lowering the Neel temperature, quantitatively increases the epsilon martensite, produced by the processing. The produced quantity of epsilon martensite in case of addition with Si is small, as compared with that in case of two-element Fe-Mn type alloy without addition and in case of addition with Co. All the tested alloys give the softening phenomenon by the martensitic transformation of gamma to epsilon. The pre-existing epsilon plate is a strong barrier for the further plastic flow, which accordingly accelerates the work hardening. 20 refs., 10 figs., 1 tab.

  20. Effects of applied stress and plastic strain on. gamma. r reversible. epsilon. martensitic transformation in high Mn alloy polyctystals. Ko Mn tetsu gokin takessho ni okeru. gamma. r reversible. epsilon. martensite hentai ni oyobosu gairyoku to hizumi no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Tomota, Y.; Piao, M.; Hasunuma, T.; Kimura, Y. (Ibaraki Univ., Ibaraki (Japan))

    1990-06-20

    The influences of applied stress and plastic strain on a transformation austenite ({gamma}) to hcp martensite ({epsilon}) were studied on Fe-16wt%Mn, Fe-24wt%Mn, and Fe-24%Mn-6%Si alloy, and a transformation mechanism and a shape memory phenomenon were more deeply examined. As the quenching structure of three kinds of the alloys consists of two phases of {gamma} and {epsilon}, the specimens were cooled after heated above the A {sub f} temperature to keep {gamma} single phase, and then the tensile tests were carried out. Positive temperature dependence was found under the 0.2% proof stress due to stress-induced {gamma}{yields} {epsilon} transformation in each of Fe-Mn alloy and Fe-24%Mn-6%Si alloy. When {gamma} phase of Fe-24%Mn alloy stabilized due to cyclic transformation was stretched at room temperature, the yield stress was remarkably lowered by the stress-induced {gamma}{r arrow}{epsilon} transformation. When the specimens were stretched at 523K under stress which was larger than the yield strength and then cooled, the elongation along the applied stress direction due to martensitic tranformation was recognized. A shape recovery was remarkable in Si content alloys. 22 refs., 5 figs.

  1. Influence of low permeability zone in blast furnace hearth on temperature distribution in furnace bottom and on iron and slag tapping indices. Koro rosho ni okeru teitsuekisei ryoiki no rotei ondo bunpu oyobi shussensai ni oyobosu eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Sawa, Y.; Takeda, K.; Taguchi, S.; Matsumoto, T.; Watanabe, Y.; Kamano, H. (Kawasaki Steel Corp., Tokyo (Japan))

    1992-07-01

    The furnace bottom brick temperature which controls the brick erosion of blast furnace bottom and the heat transfer condition of blast furnace hearth relating directly to the tapping, are studied by laboratory experiments and plant data analysis using cylindrical furnace as experimental apparatus. The temperature of the blast furnace hearth is repeated by two conditions, high temperature period and low temperature period. It is found that a zone of low permeability against the molten iron and the slag flow has existed over a wide area when the temperature at furnace bottom is low. The reason for the formation of low permeability zone has not been cleared, however it has been formed from the crystallized kiss graphite from low temperature molten iron at furnace bottom, ashes left at the furnace bottom while quenching the coal, pulverized coal and unburnt char during injection of powder coal, and this has caused the choking of coke packed bed. The concept of low permeability zone has made possible to interpret the transition of bottom bricks temperature, differences in the metal tap hole and the correlation between the flow-out index of slag and the bottom brick temperature. 17 refs. 18 figs., 2 tabs.

  2. Evaluation of seismic capacity of wall columns in high-rise reinforced concrete frame structures. Kosohekishiki ramen tekkin concretezukuri tatemono ni okeru hekichu no taishin seino hyoka ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Hiraishi, H.; Goto, T. (Building Research Inst., Tokyo (Japan)); Inai, E. (Hazama Corp., Tokyo (Japan). Technical Research Inst.); Imai, H. (Tsukuba Univ., Tsukuba (Japan)); Kano, Y. (Meiji Univ., Tokyo (Japan). Faculty of Engineering)

    1992-09-30

    So-called 'high-rise reinforced concrete frame structures (HFM) research and development project' was carried forward from 1985 to 1988. Based on the result of tests for columns carried out by the 'wall column WG' which is one of the working groups (WG), overall study is carried out on seismic capacity of wall columns provided in HFW beam direction. The items in the study are rigidity, various types of crack strength, and deformation capacity which are important for learning the seismic capacity of wall columns in the beam direction. The initial rigidity of wall columns can be estimated by the existing calculating method. The bending crack strength, bending shear crack strength, and shear crack strength of wall columns can be estimated by the existing equations. The bending strength of wall columns can be effectively estimated by the bending strength calculating expressions for earthquake-resisting walls given in this report. A design chart for the ranks of deformation capacity of wall columns is proposed. 20 refs., 21 figs., 2 tabs.

  3. Improvement of power system stability of an adjustable-speed pumped-storage generator/motor. Denryoku keito ni okeru kahensoku yosui hatsuden dendoki no keito anteido kojo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Michigami, T. (Tokyo Electric Power Co., Inc. (Japan)); Koyanagi, K. (Toshiba Corp., Tokyo (Japan))

    1994-02-20

    Recently, adjustable-speed pumped-storage generator/motor (adjustable-speed machine) is applied to power system as AFC adjusting force. This adjustable-speed machine has no problem on its stability and AC excitation control is carried out by the cycloconverter with speedy response since its being different from the conventional fixed-speed synchronous machine that the rotor speed becomes to adjustable. In this paper, aiming at the improvement of power system stability by using said adjustable-speed machine, the basic consideration on the rotor speed and reactive power control by AC excitation of the adjustable-speed machine; theoretical examination on the analysis model for analysing the system stability; analysis simulation results using two machine-pair infinite system for obtaining the basic properties of the improvement of power system stability; verification results on the effectiveness of improvement of power system stability as well as analysis model by simulative power transmission test are described. Further, the analysis simulation results on the effectiveness of improvement of power system stability by the models with the scale of practical system are reported. 11 refs., 15 figs., 9 tabs.

  4. Considerations on FEM modeling in analyzing buckling and plastic collapse of a detection control; Boto panel no zakutsu sosei hokai kaiseki ni okeru FEM model ka ni kansuru kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yao, T.; Fujikubo, M.; Yanagihara, D.; Irisawa, M. [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

    1997-10-01

    Buckling and plastic collapse of upper decks and bottom outer plates of a hull results directly in longitudinal bending collapse of the hull. Therefore, discussions were given on analysis for pressure destruction strength of a detection control panel which assumes an upper deck and a bottom outer plate. Pressure destruction behavior of the panting panel is a complex phenomenon accompanying non-linearity and geometrical non-linearity of the materials. Its whole phenomenon may be analyzed by using the finite element method (FEM) as a principle, but the analysis is not efficient. Therefore, considerations were given in relation to modeling when using the FEM. The considerations were given on a panel attached with flat steel panting members with respect to the modeling scope which considers the buckling mode according to the aspect ratio of the panel partitioned by the deflection control members. If the local buckling mode of the panel is an even number wave mode in the longitudinal direction, a triple span model is required. A modeling scope for a case of being subjected to water pressure and in-plane compression was considered on a panel attached with angle-type steel members having non-symmetric cross section. In this case, a triple bay model is more preferable to reproduce the behavior under water pressure loading. 1 ref., 6 figs.

  5. FY 1997 report of survey on the intellectual property in international collaboration research project; 1997 nendo chosa hokokusho (kokusai kyodo kenkyu ni okeru chiteki zaisanken ni tsuite no chosa hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In promoting international collaboration research project, coordination of the patent system of each country which participants to the project belong to has broad implications in concluding the contract for the project. For example, in Japan, 100% of the patent belongs to the government for contrast or collaboration project with the government. While, in the USA, the patent developed by the private company belongs to the private company even for the contrast project. In Japan, the shared patent can not be transferred to the third party or implemented without agreement with the partner. While, in the USA, the shared patent can be transferred to the third party or implemented without agreement with the partner. Due to such a difference, some projects can not be established by ill coordination of intellectual property even when the meaning of the projects is well understood. In this survey, was investigated the outline of patent systems of major countries to study about what should well balanced treatment of intellectual property in international collaboration research project be in the future. 4 figs., 8 tabs.

  6. Estimation of shallow ground structure using short-period microtremors array observation. Results in Morioka area; Tanshuki bido no array kansoku ni yoru senbu chika kozo no suitei. Moriokashiiki ni okeru kekka

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, H.; Obuchi, T.; Saito, T.; Iwamoto, K. [Iwate University, Iwate (Japan). Faculty of Engineering; Yoshida, Y. [OYO Corp., Tokyo (Japan)

    1996-05-01

    The velocity structure in the shallow ground structure was evaluated by observing microtremors of 1-10Hz in the Morioka City area. Plural wave sections free of vehicle noises or the like were selected out of the collected microtremor records, and the Fourier spectrum and coherence were calculated. Records sufficiently supporting the correlation between seismographs were chosen for the analysis. The phase velocity was calculated for each observation spot from plural array records by use of the F-K spectrum. The underground velocity structure was estimated by the inversion process using the matrix method. In this method, an early model was built on the basis of the observed phase velocity and the optimum underground velocity structure was determined by alternately performing two inversion processes: one for the case wherein the S-wave velocity is the sole parameter and the other for the case wherein the layer thickness is the sole parameter. As the result, a shallow underground velocity structure, which has good agreement with the available boring data in the Morioka City area, was successfully estimated, verifying the validity of this method. 4 refs., 7 figs.

  7. Time domain electromagnetic method for petroleum exploration. Part 3. Case study in Yoneyama area; Sekiyu tansa ni okeru TDEM ho data shutoku to kaiseki ni tsuite. 3. Niigataken Yoneyama chiiki deno tekiyorei

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, H.; Mitsuhata, Y. [Japan National Oil Corp., Tokyo (Japan); Shiga, N. [Mitsui Mineral Development Engineering Co. Ltd., Tokyo (Japan)

    1996-05-01

    The result is reported of a TDEM method-based survey for oil exploration conducted in the Yoneyama district, Niigata Prefecture. The survey covered the southern part of the sedimentary basin in the prefecture, known for the poor quality of the seismic prospecting data that had been recorded. The purpose of the TDEM method-assisted survey was to probe the high-resistivity volcanic rock structure and low-resistivity sedimentary layer, and to know their details. The obtained data were subjected to interpretation by use of the 1D inversion method. A 4000m-deep level was subjected to interpretation, 34 data were inputted, and the early model consisted of 20 layers. As the result, it was found that there was a high-resistivity layer ranging from the ground surface down to a depth of approximately 500m, that a low-resistivity layer 2500-3000m in thickness lay thereunder, and that the lowest layer had a high resistivity of approximately 100 Ohm m. By comparing these data with the geological structure, structures were disclosed corresponding to the rock bed depth, Ukawa syncline, Ishiguro anticline, and Yoneyama mountain mass. 3 refs., 10 figs., 1 tab.

  8. Fiscal 1993 investigational study of a model of international cooperation for an environmentally harmony type green technosystem; 1993 nendo Oshu ni okeru haikibutsu shori oyobi recycle no doko ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    For the natural environment preservation, effective utilization of resources, and maintenance of the ecosystem, an international cooperation model was proposed for the environmental harmony type green technosystem. A comprehensive evaluating analysis of a green forest resource, etc. as the global resource, and an intensive extraction of subjects and needs was made. The analysis was conducted of technical possibility and abstract business development effects toward the industrialization with high values added which is in harmony with the environment. As a case study, the Papua New Guinea area, Malaysia was selected and re-evaluated. For this typical tropical forest area, a new technical system was studied based on the natural environment, industry/economy, social/cultural assessment, etc., and a model for industrializing new international cooperation was proposed. For the model making for industrialization, various steps to be taken and conditions to be prepared were studied and arranged for the realization. Upon going ahead with the international technical cooperation, Japan, a large lumber consuming country, needs to always consider the fostering and effective use of lumber resource in particular. 27 refs., 28 figs., 30 tabs.

  9. Fiscal 1998 research report on the development trends of natural gas conversion technologies into liquefied fuel in Russia; 1998 nendo Roshia ni okeru tennen gas no ekitai nenryoka gijutsu no kaihatsu doko nado ni kansuru chosa kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Russia having natural gas resources largest in the world is actively promoting the basic research on liquefaction technology of natural gas such as Fischer-Tropsch (FT) synthetic catalyst, and its research potential is extremely high. This 3-year research project surveys the R and D trends of catalyst technology for liquefaction of natural gas, and fabricates the prototype FT synthetic catalyst based on the idea of Russian researchers to evaluate its feasibility experimentally. This report summarizes the following to clarify the research background: (1) The technology system for liquefaction of natural gas, and its future R and D trend, (2) The R and D trends of liquefaction technology of natural gas in the world, (3) The R and D trends of liquefaction technology of natural gas in Russia, (4) The research system of catalyses in Russia, (5) The activities of Russian catalysis research institutes, (6) The fuel liquefaction technologies of Russian major research institutes, and (7) The proposals from Russian research institutes. (NEDO)

  10. Study on the performances of handling and stability influenced by the differential terms in the state variables; Soansei ni okeru jotai hensunai no bibun yoso ga seino ni oyobosu eikyo no kento

    Energy Technology Data Exchange (ETDEWEB)

    Sugasawa, F. [Tamagawa University, Tokyo (Japan); Mori, H. [Nissan Motor Co. Ltd., Tokyo (Japan)

    1997-10-01

    The analysis method using the system matrix for state variables can not be applied to the analysis for the system has Complex Cornering Stiffness. The reason is there are differential terms in the state variables. It is found that the differential terms m the state variables can be changed to the constant terms in another state variables. 4 refs., 9 figs.

  11. Influence of fatigue frequency and hydrogen content on crack propagation in hydrogen embrittlement environment; Suiso zeika kankyoka ni okeru kiretsu denpa ni oyobosu hiro shuhasu to suisoryo no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Yamaguchi, Y.; Nakakura, M.; Nonaka, H. [Osaka Gas Co. Ltd., Osaka (Japan)

    1996-11-15

    In this paper, the influences of fatigue frequency and hydrogen content in material were investigated for the crack propagation at 0.5 stress ratio using a low alloy steel by cyclic stress in an overprotective environment. The six frequencies between 10 Hz and 0.05 Hz, and three hydrogen contents were used as the experimental conditions. Three stages divided by crack propagation behavior existed in the relationship between the stress intensity factor and the crack propagation rate. The lower the frequency was, the higher the crack propagation was at the higher stress intensity factor. The crack propagation rate was constant at Stage II. The relationship between crack propagation rate at the Stage II and frequency was expressed as (da/dn)II = 1.4 {times} 10{sup -7} {times} f{sup -0.763}. It was supposed that the cause of the Stage II was due to the lack of hydrogen to crack tip through diffusion. The hydrogen diffusion rate was of the order of 10{sup -7} m/s. The hydrogen content enhanced the crack propagation rate at 1 Hz. The Paris Law in hydrogen embrittlement environment at 1 Hz was expressed as a function of hydrogen content, which was da/dN=C({Delta}K){sup m} where C=1.72 {times} 10{sup -10} {times} (10{sup -5.6CH}), m=3.05+4.74CH, CH: Hydrogen content in material. 12 refs., 8 figs., 2 tabs.

  12. Experimental studies on bearing strength of concrete footings at exposed type of steel column bases. Tekkotsu kozo roshutsu keishiki chukyakubu ni okeru kiso concrete no shiatsu kyodo ni kansuru jikkenteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kutani, K.; Masuda, K. (University of Kyushu Sangyo, Fukuoka (Japan). Faculty of Engineering)

    1991-09-30

    Concerning concrete footings at exposed type of steel column bases, centrally applied compressive load tests and lateral load tests under constant axial compressive forces were carried out. The results of these tests presented an empirical formula for bearing strength of concrete footings at exposed type of steel column bases taking account of the flexural strength and rigidity of base plates and the height of footings. The ultimate bending strength of footings could be obtained by using bearing strength of the empirical formula, assuming the distribution of the bearing stress as a second degree parabola, and regarding it as a plain concrete column whose cross section is the effective area of base plates. When the distribution of the bearing stress was assumed to be a rectangle, the experimental strength tended to be estimated to be at a little dangerous side by axial forces over {1/2} of the maximum compressive strength. Consequently, it was verified that correlation between ultimate bending moment of concrete footings and axial forces can be predicted by using the empirical formula of bearing strength unber centrally applied compressive load. 13 refs., 17 figs., 6 tabs.

  13. Analysis of the mechanism of dynamic recrystallization in {gamma}-TiAl intermetallic compound based on texture; Shugo soshiki ni motozuku {gamma}-TiAl kinzokukankagobutsu ni okeru doteki saikessho kiko no kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Fukutomi, H.; Osuga, Y.; Nomoto, A. [Yokohama National University, Yokohama (Japan). Faculty of Engineering

    1995-12-20

    Uniaxial compression tests were conducted on the Ti-52 mol% Al intermetallic compound at the temperatures and strain rates ranging from 1173 to 1473 K and 4.0{times}10{sup -5} to 5.0{times}10{sup -3}s{sup -1}, respectively. The mechanism of dynamic recrystallization of the compound was examined on the basis of texture analysis. A fiber texture was formed during dynamic recrystallization. The main component of the texture is given approximately by (032) (compression plane) irrespective of the deformation temperatures, strain rates and strains. The sharpness of the texture varies depending on strains and the peak stresses appearing in the ale stress-true strain curves. Thus the texture formation should be attributed to the deformation process; the recrystallization process has an effect of changing the texture sharpness. One to one correspondence exists between the texture sharpness and the peak stresses when the texture sharpness is evaluated at true strains about -1.7. When the peak stress is low, the texture sharpens monotonously with increasing strain, whereas the textures at high peak stresses stop developing at the strains more than -1.0. These results suggest that the dynamic recrystallization proceeds by the mechanism succeeding to the formation of the texture by crystal slip at low peak stress conditions and the mechanism at high peak stress disturbs the texture development. The existence of the two different mechanisms which have been proposed by microstructural observation, namely strain induced grain boundary migration and the nucleation and growth mechanism, are elucidated by the texture analysis. 19 refs., 11 figs., 1 tab.

  14. Fiscal 1997 survey report on the project on energy conservation by effectively using building energy in Indonesia; 1997 nendo chosa hokokusho (Indonesia ni okeru biru energy yuko riyo ni yoru sho energy ka project chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    As an energy conservation method for a model building, the following eight methods were selected and trially calculated of the effects. 1) adoption of high efficient illumination apparatus, 2) introduction of an illuminance control system, 3) cooling water secondary pump with invertor, 4) ventilation control for parking lots, 5) heightening of the established temperature, 6) improvement of the 24-hour run chiller, 7) elevator with invertor, and 8) introduction of the photovoltaic power generation. As a result, it was found out that energy was totally reduced by about 3,837.4 MWh/yr or 25.6%. If viewed from the amount of reduction in greenhouse gas, the amount of CO2 emitted from office buildings, approximately 0.22 million t-C/yr, decreases to approximately 0.16 million t-C/yr. Further, approximately 0.93 million t-C/yr, the amount of CO2 emitted from commercial use facilities such as office buildings, department stores and hotels is reduced to about 0.69 million t-C/yr, thanks to the effect of the project on energy saving buildings, which made a CO2 reduction by approximately 0.24 million t-C/yr possible. Validity of the project on energy conservation in Indonesia was confirmed. 2 refs., 55 figs., 38 tabs.

  15. Quantum analysis in the transition process to excited state of an oxygen molecule induced by electron collisions; Denshi shototsu ni tomonau sanso bunshi ni okeru reiki jotai sen`i no ryoshironteki kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Ishimaru, K. [Gifu National College of Technology, Gifu (Japan); Okazaki, K. [Tokyo Inst. of Technology, Tokyo (Japan)

    1996-06-25

    For understanding of fundamental chemical reactions under a highly non equilibrium condition which is quite often used in plasma processing, the relevant atomic and molecular processes must be clarified. In this study, an analysis of the transition process to the excited state of an oxygen molecule induced by electron collisions in the oxygen plasma has been carried out. First, the electron density distribution in an oxygen molecule has been calculated using the extended Huckel molecular orbital method. Then, the electron potential energy distribution in the transition process to the excited state has been estimated. The electron behavior has been calculated using the estimated unidimensional electron potential energy distribution and unsteady quantum mechanics. As a result, the transition process to the excited state of an oxygen molecule induced by electron collisions and its conditions have been clarified qualitatively. 9 refs., 9 figs.

  16. Effects of the ratio of the time when wind is sensed on the comfort in a natural-ventilated room in summer. Kaki tsufu kankyo ni okeru kiryu kanchi jikanritsu no kaitekisei hyoka ni oyobosu eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Umemiya, N. (Kyoto Univ., Kyoto (Japan)); Matsuura, K. (Setsunan Univ., Osaka (Japan))

    1992-10-30

    The number of winds sensed and the ratio of time sensing were introduced as sensory indexes and their relation with the comfort index in a natural ventilated room in summer was studied. A current of air is felt uncomfortable in an air conditioned room but it is felt especially comfortable in a natural-ventilated room in summer. A field investigation was made on the third floor of a building in Kyoto for 4 days in the beginning of September. The number of winds sensed in a certain time was counted and the ratio of time sensing to the certain time was measured. The wind sensed was reported dividing into 2 categories, i.e. 'wind sensing' and 'not sensing'. In this paper, the environment and temperature distribution in the room and the appropriateness of the wind sensing reports are discussed. Then the number of winds sensed and the ratio of time sensing are studied using the data obtained and it is concluded that they are effective as comfort indexes in a natural-ventilated room. 16 refs., 15 figs., 9 tabs.

  17. Study on construction of temporary dwellings and problems caused by living long time on Hanshin-Awaji Great Earthquake; Hanshin / Awaji daishinsai ni okeru okyu kasetsu jutaku no secchi to chokikan shiyo suru baai no kadai ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, K.; Nakamura, Y. [Nagasaki Univ. (Japan)] Shimizu, Y. [Kumagai Gumi Co. Ltd., Tokyo (Japan)

    1998-10-20

    Two years after the above-titled earthquake, an examination was performed on inhabitants in the temporary dwelling houses in Kobe, center of the calamity, and problems caused by a long stay there were clarified together with a grasp of the evolving problems by comparing the result of survey carried out immediately after the disaster. The number of such temporary dwelling houses amounted to 29,128 within Kobe City and 3,168 outside of the city. According to the room arrangement, they were either one f 4 types : 2-rooms with a kitchen, 1 room with a kitchen, dormitory and those specifically for aged persons. There were 59,449 applications at the first offer of 2,702 houses. The priority of their assignments and so on are explained. As for the housing structure, numerous complaints concerned with the room temperature, noise and so forth. As for the living environment, lack of nearby commodity shop, omission of transportation access, ill drainage of the housing sites were pointed out and the matters of demand to the local authorities included the installation of mail post and street lights. As for the health management, insomnia, stiff shoulder, lumbago and other bad physical conditions were revealed. The financial difficulty and the high house rent were obstacles to migrate to other places. The prolonged temporary lives worsened the apprehension of dwellers for the earthquake, typhoon, fire and alike. Some features for the calamity are described in comparison with the result of survey on those who were compelled to live under similar conditions by the eruption of Mr. Fugen. 6 refs., 13 figs., 15 tabs.

  18. FY 2000 report on the basic survey to promote Joint Implementation, etc. Energy conservation by modernization of a cement plant (Double Horse Cement Co.) in China; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Chugoku cement kojo (Double Horse Cement) kindaika ni yoru sho energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    An investigational study was conducted of possibilities of energy conservation and greenhouse effect gas emission reduction in the cement production process of Double Horse Cement Co., Mianyang City, Sichuan Province, China. Double Horse Cement adopts the wet type long kiln production system and has a production ability of approximately 1.5 million t/y. In the project, as to three production lines out of the six production lines, improvement was planned to be made of the technologies on the following: mixing of raw materials, grinding of raw materials, NSP, clinker cooler, clinker pre-grinder, high-efficiency separator, waste heat use power generation, etc. As a result of the study, it was found that the energy conservation amount obtained was 54,646 toe/y. And, the amount of greenhouse effect gas reduction was 169,086 t-CO2/y. The total fund required for this project was approximately 5.553 billion yen and the internal earning rate was 7.36% after tax. When the project is carried out, expenses vs. effects are 9.8 toe/million yen in energy conservation amount and 30.4 t-CO2/million yen in greenhouse effect gas reduction. (NEDO)

  19. OpenNI cookbook

    CERN Document Server

    Falahati, Soroush

    2013-01-01

    This is a Cookbook with plenty of practical recipes enriched with explained code and relevant screenshots to ease your learning curve. If you are a beginner or a professional in NIUI and want to write serious applications or games, then this book is for you. Even OpenNI 1 and OpenNI 1.x programmers who want to move to new versions of OpenNI can use this book as a starting point. This book uses C++ as the primary language but there are some examples in C# and Java too, so you need to have about a basic working knowledge of C or C++ for most cases.

  20. ANTIČNI ATOMIZEM

    OpenAIRE

    Žnidaršič, Miran

    2014-01-01

    Antični filozofi Levkip, Demokrit, Epikur in Lukrecij so razvili filozofijo atomizma, ki postavlja za osnovo vsega neštete nedeljive in nezaznavne delce. Ti delci ali atomi zadevajo eden ob drugega, se odbijajo in zapletajo v neskončni praznini ter na ta način tvorijo zaznavna telesa. Ker lahko vse, tudi dušo, zreduciramo na atome, ti pa so najmanjši delci materije, veljajo atomisti za prve materialiste. Gibanje pa je posledica medsebojnega delovanja atomov, zato je njihov nazor mehanistični....

  1. Ni landsbyer i Danmark

    DEFF Research Database (Denmark)

    Larsen, Jacob Norvig

    Denne rapport beskriver en evaluering af statsstøttede forsøg med at styrke og udvikle mindre lokalsamfund. Forsøgene er gennemført i ni kommuner. Da der i disse år er stor opmærksomhed om de små byers og samfunds udviklingsmuligheder, har erfaringerne fra forsøgsprojekterne bred interesse...

  2. Frenkel defects in Ni and Ni-base alloys

    International Nuclear Information System (INIS)

    The defect structure produced by low temperature (4K) electron irradiation in single crystals of Ni, Ni62Cu38 and Ni3 Fe was investigated by measurements of the diffuse scattering of X-rays (Huang Diffuse Scattering), the change of the lattice parameter and the change of the electrical resistivity: The volume relaxation and the structure of the self interstitial atom (SIA) is very similar for the alloys and the pure fcc metals. The interstitial clustering processes during stage I and II proceed progressively more slowly in Cu, Ni, NiCu and Ni3Fe respectively. In Ni3Fe even the di-interstitial seems immobile up to stage III. The formation of large vacancy agglomerates during stage III annealing is only observed with the pure metals Ni and Cu. Interstitial mobility during annealing in stage II contributes to the decomposition of NiCu but not to the ordering of Ni3Fe. There is an increase of order for highly ordered Ni3Fe (S = 0.7) during annealing in stage III and, within the errors, no change for samples with S = 0. (author)

  3. Room temperature ferromagnetism of Ni, (Ni, Li), (Ni, N)-doped ZnO thin films

    Institute of Scientific and Technical Information of China (English)

    AU; ChakTong

    2010-01-01

    Ni-doped ZnO thin films (Ni concentration up to 10 mol%) were generated on Si (100) substrates by a sol-gel technique. The films showed wurtzite structure and no other phase was found. The chemical state of Ni was found to be bivalent by X-ray photoelectron spectroscopy. The results of magnetic measurements at room temperature indicated that the films were ferromagnetic, and magnetic moment decreased with rise of Ni concentration. The magnetization of Ni (10 mol%)-doped ZnO film annealed in nitrogen was lower than that annealed in argon, suggesting that the density of defects had an effect on ferromagnetism.

  4. Fiscal 1997 for the upgrading of the Asia/Pacific coal development. Survey of the optimization of the coal transportation system in Indonesia; 1997 nendo Asia Taiheiyo sekitan kaihatsu kodoka chosa. Indonesia ni okeru sekitan yuso system saitekika chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper summarized the results of Phase 1 and Phase 2 surveys conducted based on `Agreement on the comprehensive survey of a coal transportation system in South Sumatra` concluded between NEDO and the Ministry of Mine and Energy in Indonesia. In addition to the data collection and site surveys made in Phase 1, conducted in Phase 2 were determination of sites for harbors, determination of a scenario on coal transportation from coal mines to harbors, optimization of the coal transportation system, social/economic assessment, and proposal on the optimum transportation system. The results of the simulation were as follows: It is the most advantageous to transport coal from coal deposit area to harbor by rail and from harbor to Paiton by barge weighed over 10,000 tons. Tanjung Api Api is the most advantageous as harbor. The production scale which is profitable became more than 15 million tons. The present coal price of PTBA is $25/t arriving Suralaya. The coal in this case is said to be 5500kcal/kg in quality, and the coal of the same quality to this is only profitable. 8 refs., 68 figs., 104 tabs.

  5. Effect of intermolecular cohesion on coal liquefaction. 3. Reactivity of oxygen methylated coal; Sekitan teibunshika hanno ni okeru bunshikan gyoshuryoku no koka. 3. O-methyl ka tan no hanno tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, M.; Nagaishi, H.; Yoshida, T. [Hokkaido National Industrial Research Institute, Sapporo (Japan)

    1996-10-28

    The reactivity of oxygen methylated coal was studied to control hydrogen bond in bituminous coal liquefaction and intermolecular cohesion such as van der Waals force. In experiment, crushed and dried Illinois coal of 100mesh or less was used as specimen, and oxygen methylated coal was prepared by Liotta`s method using tetrabutylammonium halide. Coal liquefaction was conducted in an electromagnetic agitation autoclave using tetralin solvent under initial hydrogen pressure of 100kg/cm{sup 2} while heating. The molecular weight distribution of the products obtained was measured by gel permeation chromatography (GPC) analysis. The experimental results are as follows. The effect of intermolecular cohesion in bituminous coal on the reactivity is mainly derived from decomposing reaction from preasphaltene to oil. Yields of oil fraction by methylation increase corresponding to release of intermolecular cohesion. Since the thermal release is promoted with temperature rise, the difference in yield due to different treatments decreases. 5 refs., 3 figs., 1 tab.

  6. Coliquefaction of coal, tar sand bitumen and plastic (interaction among coal, bitumen and plastic); Sekitan/tar sand bitumen/plastic no kyoekika ni okeru kyozon busshitsu no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Yamaguchi, H.; Okuyama, Y.; Matsubara, K. [NKK Corp., Tokyo (Japan); Kamo, T.; Sato, Y. [National Institute for Resources and Environment, Tsukuba (Japan)

    1996-10-28

    For the improvement of economy, coliquefaction of coal, tar sand bitumen and plastic was performed under low hydrogen pressure, to investigate the influence of interaction among these on the liquefaction characteristics. For comparison, coliquefaction was also performed under the hydrogen pressure same as the NEDOL process. In addition, for clarifying its reaction mechanism, coliquefaction of dibenzyl and plastic was performed as a model experiment, to illustrate the distribution of products and composition of oil, and to discuss the interaction between dibenzyl and various plastics, and between various plastics. Under direct coal liquefaction conditions, coprocessing of Tanito Harum coal, Athabasca tar sand and plastic was carried out under low hydrogen pressure with an autoclave. The observed value of oil yield was higher than the calculated value based on the values from separate liquefaction of coal and plastic, which suggested the interaction between coal and the mixed plastic. The results of coliquefaction of coal, tar sand bitumen and plastic could be explained from the obtained oil yield and its composition by the coliquefaction of dibenzyl and plastic. 2 refs., 3 tabs.

  7. Catalytic activity and selectivity of potassium-promoted ultrafine particles of iron for liquid phase fischer-tropsch synthesis. Ekisoho fischer-Tropsch gosei ni okeru kariumu shushoku tetsu biryushi shokubai no kassei oyobi sentakusei

    Energy Technology Data Exchange (ETDEWEB)

    Ito, Hiroyuki; Ono, Tomoyuki; Nagano, Shin' ichi; Kikuchi, Eiichi (Waseda Univ., Tokyo (Japan). School of Science and Engineering)

    1989-11-01

    In the previous work, ultrafine particles (UFP) of Fe were used as catalyst for liquid phase Fischer-Tropsh synthesis, then it was found that the catalytic activity of Fe UFP was greater than that of ordinary precipitated Fe catalyst. In the present work, the catalytic activity and selectivity of K-promoted Fe UFP at a high temperature (300 centigrade) were investigated. The reaction was conducted in a slurry-bed high pressure flow type recycling reactor, and the addition of potassium was carried out using suspension of potassium metal. Using catalyst was Fe UFP, which were prepared by the gas evaporation method and had an average particle size of about 20nm. In the reaction at 300 centigrade and 30 atm, the activity of promoted Fe UFP catalyst remarkably increased with time on stream, in contrast to the deactivation of unpromoted Fe UFP catalyst and the precipitated Fe catalysts. From the results of the X-ray diffraction analysis of used catalysts, it is deduced that the enhancement of the activity of promoted catalyst is attributed to the formation of iron carbide which is promoted by potassium. It is considered that the modification effect of potassium is shown at higher temperature and the high selectivity is given even at a high temperature. 6 refs., 3 figs., 2 tabs.

  8. Occurrence of Giardia cysts and Cryptosporidium oocysts in sewage and their reduction in treatment process; Gesuichu no Giardia shisuto oyobi Cryptosporidium oshisuto noudo to gesui syori ni okeru jyokyosei

    Energy Technology Data Exchange (ETDEWEB)

    Hashimoto, A.; Hirata, T. [Azabu University, Kanagawa (Japan); Magara, Y. [National Institute of Public Health, Tokyo (Japan); Ogaki, S. [The University of Tokyo, Tokyo (Japan)

    1997-06-10

    Recently, the water system infection owing to protozoan, virus and so on which is different from the conventional infection like represented by bacteria, is reported. There are few examples for the infection conditional study and epidemiological investigation of these protozoan and virus in Japan. Authors carried out a field survey at nine sewage treatment plants, in order to investigate the occurrence of Giardia cysts and Cryptosporidium oocysts in raw sewage and the removal in sewage treatment processes. As a result, in all plants, Giardia cysts were detected in raw sewage and effluent of primary sedimentation. Cryptosporidium oocysts were detected from only one raw sewage sample. Indicator bacteria counts tested, C.perfringens spores, coliforms and E.coli, were statistically correlated with Giardia cyst densities and the most significant relationship was observed between C.perfringens spore counts and Giardia cyst densities. It was found that turbidity was the most appropriate indicator for Giardia cyst removal in activated sludge treatment process. 18 refs., 6 figs., 2 tabs.

  9. 55th electric science promotion prize (progress prize). Demonstration of optical soliton transmission on OPGW first in the world; Dai 55 kai denki gakujutsu shinkosho (shinposho) jusho. Seiaihatsu no OPGW ni okeru hikari soriton denso no jissho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-06-10

    Electric science promotion prize (progress prize) is given to `Person who newly proposed a new concept, theory, material, device, system and method on electrical science and technology, or demonstrated these proposals` by the commendation committee of Institute of Electrical Engineers of Japan every year. Eight promotion prizes including that for Kansai Electric Power`s `Demonstration of optical soliton transmission on OPGW first in the world` were given. This research succeeded in development of the transmission/ receiving device suitable for optical soliton transmission, and the prediction method of an optimum transmission condition by computer simulation. In addition, this research succeeded in 10Gbit transmission of 784km and 40Gbit transmission (4-wave multiplex) of 392km by applying the above research result to Okurobe trunk line OPGW (98.2km). This demonstration of optical soliton transmission on OPGW is first in the world. (NEDO)

  10. Transmission test in connection of different types of optical fibers: a dispersion-shifted single-mode optical fiber (DSF) and a single-mode optical fiber (SM); DSF-SM ishu hikari fiber setsuzoku ni okeru denso shiken

    Energy Technology Data Exchange (ETDEWEB)

    Uemura, J. [Chugoku Electric Power Co. Inc., Hiroshima (Japan)

    1998-08-25

    The currently used optical transmission system usually uses a single-mode optical fiber (SM) with 1.3 {mu} m band. For sections requiring long-distance transmission, a dispersion-shifted single-mode optical fiber (DSF) with 1.55 {mu} m band is beginning to be partly used. If, in using these fibers, the different types of optical fibers, SM and DSF, can be used directly connected with each other, structuring an economical optical communication network including the existing SM fibers may become possible. This paper describes measurements of connection loss between the different optical fibers of DSF and SM, a transmission test on the connection between the different optical fibers of DSF and SM by using an amplifier for optical fibers used in an actual field, and an optical wave multiplex transmission test. The measurements and the tests were carried out in winter and summer of 1997 by using the existing OPGW optical fibers among the Okayama substation, the Higashi-Okayama substation, and the Susai substation. The connection between the different optical fibers of DSF and SM generates greater connection loss than in connection with the same type of fibers due to difference in the mode field diameters. Therefore, it will be necessary in constituting an optical fiber line to incorporate connection loss of about 1 to 2 dB in connector connection and about 0.5 to 1 dB in welding connection. 1 ref., 17 figs., 7 tabs.

  11. Novel sensorless starting and low speed drive of cylindrical brushless DC motor using eddy current with un-known load; Uzudenryu wo riyoshita entogata brushless DC motor no futokutei fukaji ni okeru sensorless shidoho oyobi teisoku kudoho

    Energy Technology Data Exchange (ETDEWEB)

    Tomita, M.; Doki, S.; Okuma, S. [Nagoya University, Nagoya (Japan); Yamaguchi, H. [The Aichi Electric Co. Ltd., Aichi (Japan)

    1998-04-01

    Sensorless starting and low speed drive of a cylindrical brushless DC motor with un-known load have been a difficult problem because an electromotive force does not arise enough at the starting and at low speeds and an inductance is constant irrespective of rotor position. In this paper, it is proposed to paste non-magnetic material and to measure a voltage of an opened phase to realize sensorless starting and low speed drives. The method is shown very feasible by experiments. 13 refs., 17 figs., 2 tabs.

  12. Development of iron oxide bubbling fluidized bed in direct causticization process; Chokusetsu kaseika purosesu ni okeru tekkoseki wo ryudo baitai oyobi hannozai to suru koon kiho ryudoso no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Nagai, C. [Kawasaki Heavy Industries Ltd., Hyogo (Japan)

    2000-11-10

    An iron oxide bubbling fluidized bed reactor in the direct causticizing process, which constitutes the main part of the process, is developed. Its optimum operating conditions and reaction characteristics were investigated through a 500 mm sq. bench scale test. In this process, high-grade iron oxide, whose diameter is 0.2 - 1.0 mm was used as causticizing agent as well as the bed material. Concentrated black liquor was fed over the bubbling iron oxide bed by means of a spray nozzle at the temperature of 1,173 {approx} 1,273 K. Reacted sodium ferrite was hydrolyzed to recover sodium hydroxide and residue iron oxide was recycled. During the reaction in the bed as well as hydrolysis, iron oxide particle is gradually attritted so that the operation of fluidized bed becomes difficult. A portion of the iron oxide fine particles was pelletized by compaction before it was recycled to the reactor. The minimum ratio of fines to be pelletized is found to be 50 % to maintain the bed as well as to recover sodium from black liquor through 40 hrs' of continuous operation of the bench scale test. (author)

  13. Utilization of two-way multicore cables and comparison of various electrode configurations in electrical prospecting; Denki tansa ni okeru sohokogata tashin cable no riyo to kakushu dekyoku haichi no hikaku

    Energy Technology Data Exchange (ETDEWEB)

    Takakura, S. [Geological Survey of Japan, Tsukuba (Japan); Matsushima, J. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

    1996-10-01

    For more precise electrical prospecting, the new multicore cable was developed to allow high-density measurement by conventional equipment. Since conventional multicore cables are inferior in cost, length and weight, the new cable is composed of an n-conductor cable, two n-conductor male connectors and n lead wires. For connection of the multi-conductor cable and lead wires, cable sheath is peeled at n points at specific intervals. Sheath of the k-th conductor is peeled at k-th point from the terminal, and restored for insulation after connection of the conductor and lead wire. The male connectors are attached to the both ends of the multi-conductor cable. Since this two-way type cable can be used at every end, the measuring equipment can measure at one divisional point after another of a long measuring line while shifting the equipment from one point to another. All measurements are perfected only with two short cables. Resistivities were successfully measured along the long measuring line of 480m long with 97 electrodes arranged at intervals of 5m. Various electrode configurations were also compared. 1 ref., 4 figs., 2 tabs.

  14. Application of magnetotelluric method to hydrocarbon exploration. Case study of MT survey in Yurihara oil and gas field, Akita prefecture; MT ho no kokunai sekiyu tanko eno tekiyo. Akitaken Yurihara chiiki ni okeru jikken chosa kekka

    Energy Technology Data Exchange (ETDEWEB)

    Mitsuhata, Y.; Matsuo, K.; Ishikawa, H.; Tanaka, H.; Nakagami, K. [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1996-10-01

    The experiment and survey were carried out to verify the effectiveness and limitation of MT method. The previous seismic reflection method is unsuitable for steep terrain and over-folded complicated geological structure. In such difficult areas, application of MT method is increasing as complement or substitution for the reflection method. However, the evaluation of resistivity structure interpretation for every area is slightly difficult because of lack of data, poor quality of data, and no verification data at boreholes. Consequently, the survey was again carried out in well-known Yurihara oil and gas field, Akita prefecture whose geological structure has been surveyed in detail at boreholes, by adding new 32 sites, 22 sites on the south side and 10 sites on the north side of the measuring line extending from east to west. As a result, it was clarified that the lower high-resistivity layer found by MT method is equal to the Nishikurosawa basaltic layer, and basalt extends to the west in the north area. This result can`t be simply compared with the previous geological profile. 8 refs., 8 figs.

  15. Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Survey by region/industry in India; Kankyo chowagata sekitan riyo system kanosei chosa. Indo ni okeru sekitan riyo gaikyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A survey was made in India which is a coal producing/consuming country following China in Asia and where coal is used for about 60% of the primary commercial energy. The survey was conducted on coal production/distribution/utilization and environmental issues, aiming at studying feasibility of introducing the environmentally friendly coal utilization system into every industry including the residential/commercial one, and at implementing a comprehensive master plan including Japan`s international cooperation. Total power source facilities in fiscal 1995 are 83.3 million kW, 64% of which are coal thermal power facilities and generated 260 TWh, 69% of the total output energy. Main commercial energy sources are coal, oil and natural gas, and oil is self-sufficient. The survey this time did not examine very well the actual state of the environmental pollution problem caused by the coal utilization. Indian coal is high in ash content but low in sulfur content, and therefore, SOx polluting air has not been a very important problem so far, but soot/smoke is almost the problem. Further, ash treatment after combustion at boilers, etc. is expected to be a big problem in the future. 49 figs., 88 tabs.

  16. Simulation method of ATM switch architecture and proposal for the delay priority control in ATM crosspoint switch; ATM kokanki no simulation shuho to crosspoint switch ni okeru chien yusen seigyo no teian

    Energy Technology Data Exchange (ETDEWEB)

    Doi, H. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1996-03-01

    A simulation method for switch analysis of ATM (asynchronous transfer mode) switch architecture has been developed. When various electric power information is integrated in the ATM switch architecture, delay priority control method has been proposed, by which the delay time and delay time fluctuation can be guaranteed for important information, such as system protection control information. The simulation method has been developed for analyzing the output buffer type crosspoint switch. The analysis solutions of waiting time of cells at the switch were determined and compared with the simulation results. The both agreed well mutually, and the validity of this method was confirmed. Priority was added to the cells of crosspoint switch, and different buffer was given for each priority, to exchange the important information, selectively. Thus, a switch was proposed, by which the delay time and delay time fluctuation can be restricted. The mean waiting time of the high class cells was suppressed less than 1 cts even at the switch load factor of 0.98, and the fluctuation range of 4 cts was guaranteed. 11 refs., 19 figs.

  17. Study of numerical simulations concerning the performance of antennas used for automobile wireless communications; Jidosha no musen tsushin ni okeru antenna seino hyoka no tame no suchi simulation no ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Sueyoshi, M.; Yano, T.; Noda, Y.; Goto, H. [Honda Lock Mfg. Co. Ltd., Tokyo (Japan)

    1997-10-01

    Automobiles and communication technologies will be more closely related with each other in the advanced intelligence society. Anti-theft security systems apply those technologies, where antenna performance is one of the key elements. This is a study of numerical simulations of the performance of those vehicle antennas. 2 refs., 2 figs.

  18. Stress-induced transformation of retained austenite and residual stress in polishing and grinding of ADI. ADI no kenma kensaku kako ni okeru zanryu austenite no kako yuki hentai to zanryu oryoku

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, T.; Tada, S.; Abe, T. (Government Industrial Research Institute, Tohoku, Sendai (Japan)); Kurihana, S. (Fukushima Prefectural Office, Fukushima (Japan))

    1993-06-25

    In the present research, relation between the retained austenite ([gamma]) and residual stress (Sr) on the mechanically worked surface was investigated by an X-ray diffraction to furthermore reform the ADI (Austempered Ductile Iron) which is high toughness automobile part material. As samples, selected were two types of ductile iron which are equivalent to FCD450 and FCD600, respectively. In the main process of thermal treatment, they are austenitized in argon at 1173K in the furnace, held quickly cooled (to between 573 and 648K) a cooled at room temperatures. After the treatment, both of them have no structural differences. As a result of investigating the relation of [gamma]'s stress-induced transformation on the polished and ground surface to both Sr and carbon concentration, the vol% of [gamma] on the worked surface by silicon carbide waterproof abrasive paper and buff is small on the surface where the Sr is high, and both of them are mutually correlative. The [gamma] is so quasi-stable as to be martensitized, if worked, and degraded in mechanical properties. The low carbon ductile iron (less than 1.4% in carbon content) is easy to transform, while the high carbon ductile iron (more than 1.6% in carbon content) is difficult to transform and its [gamma] is stable for the working. 16 refs., 8 figs., 2 tabs.

  19. Filament coupling in rapid-quenched and transformed jelly-roll Nb{sub 3}Al multifilamentary conductors; Kyunetsu kyurei{center_dot}hentai ho jieriroru Nb{sub 3}Al tashin senzai ni okeru fuiramento ketsugo

    Energy Technology Data Exchange (ETDEWEB)

    Banno, N.; Takeuchi, T.; Ito, K.; Wada, H. [National Research Institute for Metals, Tokyo (Japan); Japan Science and Technology Corporation, Saitama (Japan); Kosuge, M. [National Research Institute for Metals, Tokyo (Japan); Tagawa, K. [Japan Science and Technology Corporation, Saitama (Japan); Nakagawa, K. [Hitachi Cable Ltd., Tokyo (Japan)

    2000-05-29

    In Nb{sub 3}Al wire described in the above title, filaments are adjacent to each other and bridging between filaments and proximity effect are worried about. In three kinds of wires with different diameter, A15 phase was formed via supersaturated solid solution by heat treatment of rapid heating/quenching and transformation. By measuring magnetization characteristics, hysteresis loss and critical current density, the equivalent filament diameter was determined. As the result, it was found that hysteresis tends to become less with larger diameter of filament at higher temperature. Also, from magnetic field dependence of equivalent filament diameter, the possibility that bridging occurred in the sample with shortest distance between filaments and the proximity effect occurred in longer distance between filaments was shown. (NEDO)

  20. Fiscal 1997 survey report. Feasibility study of the environmentally friendly type coal utilization system (survey of the coal utilization in Pakistan); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Pakistan ni okeru sekitan riyo gaikyo chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper made a literature survey, hearing survey, site survey/study on the coal in Pakistan such as the coal utilization system and the environmental situation, etc., and aimed at pre-examination for the survey of the introduction of the environmentally friendly type coal utilization system to be planned in Pakistan in the future. The examination, data collection and preparation were conducted in terms of the following items: the structure of coal consumption in energy supply, structure of coal consumption, mainly of domestic brown coal consumption, the situation of coal utilization by industry and by region, environmental problems caused by coal utilization such as air pollution, the trend of policies of environmental regulation, etc. The literature on the following was obtained and surveyed: the situation of economy/energy in Pakistan, coal utilization technology by industrial field, and environmental protection technology. The hearing survey was made to institutions concerned, corporation groups and men of learning and experience. Site surveys were conducted for the typically selected coal utilization equipment and existing environmental protection equipment. 66 figs., 56 tabs.

  1. Measures in progress for distribution facilities automation and cost reduction. Direct supply of 400V to South Port Cosmo Square, Osaka; Susumu haiden setsubi no jidoka, cost teigen taisaku. Nanko cosmo square ni okeru 400 volt chokusetsu kyokyu no donyu

    Energy Technology Data Exchange (ETDEWEB)

    Kanamori, Y. [Kansai Electric Power Co. Inc., Osaka (Japan)

    1998-07-01

    Kansai Electric Power Co., Inc., has been working to elevate the distribution voltage of 6kV to 20kV, which is to respond to increasing demand for power. Using the experience of this approach, the corporation has designated Cosmo Square as a model area and plans to directly supply 400V to the area which is the voltage that clients demand. In this report, the plan is summarized and some examples of power receiving equipment newly developed for Cosmo Square are described. Cosmo Square has been developed to be a new base of international business, and lotting-out is now in progress. Upon completion, the center will be a group of gigantic buildings of which more than half will be creating a contract demand of 1000kW or more per building, and is expected to be consuming a total of 190MW finally. Power facilities under construction are to handle 20kV, and the voltage of 20kV will be stepped down to 400V for directly supply to 50-2000kW consumers. It is expected that, in this way, there will be various merits embodied, such as an extensive cost reduction in the construction of receiving equipment and other devices, efficient utilization of 230/400V appliances now in popular use, and reduction in safety-related expenditures. 4 figs.

  2. Recent development of automation, robotization CIM based on systematization of welding operations in the shipyard; Yosetsu no jidoka robot ka CIM ka ni okeru zosen no taio to kongo no hoko

    Energy Technology Data Exchange (ETDEWEB)

    Iwabuchi, H. [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

    1997-12-01

    This paper describes history, current status and future direction of automation, robotization and CIM during welding operations in the shipbuilding industry. The shipbuilding industry in Japan has experienced big booms and slumps for 20 years from the 1970`s to the 1990`s. Improvement of productivity by introducing welding robots has greatly contributed to the recovery basis in the 1990`s. For example showing current status, sub-assembly welding robots can automatically make their operation data and work by means of off-line teaching method from design information including shape. In the curved large-scale assembly process, welding is automatically performed only using inputting designed data of ship type by combining automatic setting of outer plates with positioner. Improvement of accuracy, robotization of welding of curved part, and field works without monitoring are essential in the future. Development combined with image analysis technology is to be promoted. 4 refs., 16 figs., 1 tab.

  3. Automated dam concrete driving system for Ichinoki dam construction work. Unmanned manufacture and transportation; Ichinoki dam kensetsu koji ni okeru dam concrete dasetsu sagyo jidoka system. Seizo unpan sagyo no mujinka seko

    Energy Technology Data Exchange (ETDEWEB)

    Kobayashi, I.; Yoneda, Y.; Nakayama, T.

    1995-02-25

    Introduced herein is the automated dam concrete driving system adopted for the construction of the Ichinoki dam (bank height: approximately 38m, bank volume: approximately 65,000m{sup 3}) located in Nara Prefecture. This system has been developed so that safety and efficiency may be enhanced throughout the whole driving process by a method wherein all the mechanical facilities involving the extraction of aggregate and the mixing, loading, transportation, and driving of concrete are mutually linked and placed under a comprehensive management; the batcher plant and transfer vehicles are capable of completely unmanned operation using handy radio terminals; and automatic hydraulic pressure generating concrete buckets are incorporated. Outlined herein also are the radio data transmission system, automated dam concrete mixing system, automated dam concrete loading/transporting system, consistency deciding system capable of instantaneously grasping the properties of the mixed cement, and the actual operating records of this system. 13 figs., 2 tabs.

  4. Evaluation of ground properties in deep soil improvement method and its application to automization of construction; Shinso kongo shori koho ni okeru jiban hyoka to sono jidoka seko eno oyo

    Energy Technology Data Exchange (ETDEWEB)

    Tateyama, K. [Kyoto University, Kyoto (Japan). Faculty of Engineering; Fukagawa, R. [Ehime University, Ehime (Japan). Faculty of Engineering; Tsuji, T. [Kobe Steel, Ltd., Kobe (Japan)

    1996-03-21

    The evaluation method of ground properties based on mechanical load during construction was studied for powder jet mixing method in deep soil improvement. In the theoretical study, mixing torque and N value in standard penetration test were used as machine load and ground property, respectively, and the relational expression between internal friction angle of ground and cohesion was derived. To verify the validity of calculation results, the mixing torque, penetration rate and N value were measured and compared at 18 spots of 6 construction fields. Boring survey was carried out at the measuring spots to obtain the N value distribution to depth prior to the experiment. As a result, in both sand and clay ground, the relation among the mixing torque, penetration rate and N value could be expressed by the same type of the relational expression although expression`s coefficients were different from each other. In sand ground, the measured values relatively well agreed with the calculated values at 2-3 in increase magnification of the pressure derived from volume expansion of soil due to mixing. 9 refs., 15 figs.

  5. Stratigraphy and eruption ages of deposits at the southeast side of Nishiyama volcano, Hachijo island during the last 2,500 years; Hachijojima, Nishiyama kazan nantoroku ni okeru saikin 2,500 nenkan no funshutsubutsu no sojo to funka nendai

    Energy Technology Data Exchange (ETDEWEB)

    Sugihara, S.; Shimada, S. [Meiji University, Tokyo (Japan)

    1998-10-25

    The Nishiyama volcano of the Hachijo island is a stratovolcano whose volcanic activity started approximately 10,000 years ago. Among the lateral volcanos surrounding the cone-shaped mountain, there is a Kandoyama tuff cone formed by a phreatomagmatic eruption at the southeastern base of the Nishiyama volcano. It is known that Kandoyama`s latest eruption is not older than 4,000 years. In this report, the stratigraphy of eruptive deposits and the types of eruptions involving Nishiyama after Kandoyama formation are clarified. Also, the history of Nishiyama` eruption is discussed, for which a study is made about the stratigraphic relationship between its eruption and the results of {sup 14}C dating or the eruption remainders, corresponding terrestrial episodes recorded in ancient literature usable for eruption dating, etc. The conclusion is summarized below. The eruptive deposits are to be supposedly dated at a period after the completion of caldera aggradation. At the southeastern base of Nishiyama, the eruption of 1605 is to immediately follow the eruption of approximately 1,100 years ago, and no eruption so active as to cause the outflow of lava is noticed therebetween. It is inferred that the Nishiyama volcano erupts once in a period of 300-700 years. 44 refs., 11 figs., 2 tabs.

  6. Range of wavelengths possible to estimate phase velocities of surface waves in microtremors; Bido tansaho ni okeru suitei kanona bidochu no hyomenha iso sokudo no hacho han`i

    Energy Technology Data Exchange (ETDEWEB)

    Miyakoshi, K.; Okada, H.; Ling, S. [Hokkaido University, Sapporo (Japan)

    1996-05-01

    To specify the maximum wavelength of the phase velocities that can be estimated by the spatial autocorrelation (SPAC) method or F-K method in microtremor exploration, investigations were conducted using numerical simulation. In view of feasibility, an equilateral triangle array was employed, the maximum radius of the array having 7 observation points being 0.10km. The dispersion curve of the Rayleigh wave basic mode was calculated from an underground structure model. White noise was used as the incident wave, and, in case the waves came in from multiple directions, a different phase spectrum was assigned to each direction. In searching for the maximum wave length of phase velocities that could be estimated, a limit was imposed upon estimation, and it was prescribed that the wavelength be the limit if the difference between the theoretical value and estimated phase velocity was 5% or higher. As the result, it was found that it is possible to estimate the phase velocity when the wavelength is up to approximately 10 times longer than the array maximum radius in the SPAC method, and up to approximately 5 times longer in case of the F-K method. 10 refs., 5 figs., 1 tab.

  7. Potential denitrification rates of subsurface soil under paddy fields receiving ground water with high nitrate concentration; Konodo shosantai chisso gan`yu chikasui no ryunyusuru suiden kasodo ni okeru dacchitsu kassei

    Energy Technology Data Exchange (ETDEWEB)

    Toda, H. [Shizuoka Agricultural Experiment Station, Shizuoka (Japan); Hidaka, S. [Saitama Agricultural Experiment Station, Saitama (Japan)

    1996-02-10

    It is well known that the concentration of nitrate nitrogen in the surface water decreases as it flows downward in rice paddies irrigated with water high in nitrate nitrogen concentration. The decrease is attributed to absorption by rice plants and algae adherent thereto and denitrification in the reduction layer well developed in the rice paddy surface soil. In paddy fields downstream of the Kushibiki plateau in the northwestern part of Saitama Prefecture, it is occasionally observed that nitrate nitrogen concentration in the ground water decreases as it flows down (farther from the plateau) not only in the flooded period but also in the non-flooded period. This suggests that in the said paddy field denitrification takes place not only in the rice paddy surface layer soil but also in the lower layer soil. Under the circumstances, the denitrification rate in the rice paddy lower layer soil was measured using the acetylene inhibition method under anaerobic and added nitrate conditions. A denitrification rate of 0.4-46ngN/g{sup -1} wet soil/h{sup -1} was obtained from a 40-150cm deep layer soil, smaller by the order of 1-2 than that in the surface layer soil. This suggests that the lower layer soil contributes to denitrification. 17 refs., 3 figs., 1 tab.

  8. 2D inversion results and interpretation of CSAMT data in the Itaya prospect, Northern Honshu, Japan; Tohoku nanbu chiiki Itaya chiku ni okeru CSAMT ho nijigen kaiseki kekka to sono kaishaku

    Energy Technology Data Exchange (ETDEWEB)

    Yoshioka, K.; Hishida, H.; Katayama, H. [Metal Mining Agency of Japan, Tokyo (Japan); Takakura, S. [Geological Survey of Japan, Tsukuba (Japan)

    1997-05-27

    A two-dimensional analysis was carried out on electric exploration data obtained by using the CSAMT method in the Itaya prospect in the southern part of the Tohoku region in Japan. Considerations were given on mine exploration targets. Gold produced in this area is contained in stockwork or vein deposited quartz in silicified hydrothermal breccia. Therefore, the exploration targets are silicified rocks that show high resistivity. The field investigation using the CSAMT method was conducted by installing a dipole source of about 1.9 km as a transmission source at a location about 6 km apart from the investigation area, and by measuring transmission currents from 8 to 10A and ten frequencies from 4 to 2048 Hz. The two-dimensional analysis was performed by using programs of a forward calculation that used a finite element method and of an inversion calculation that used a least-squares method. Analysis utilizing resistivity of the boring cores made minimizing RMS misfit possible. As a result, estimations were made on distribution of silicification and claying alteration from the detailed resistivity distribution around the Itaya mine. 5 ref., 8 figs.

  9. Experiment for deep seismic reflections in Hidaka, Hokkaido. Comparison between Vibroseis and explosive data; Hidaka chiiki ni okeru shinbu hanno data no shutoku jikken. Vibroseis to dynamite no hikaku

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, N.; Ikawa, T. [Japex Jeoscience Institute, Tokyo (Japan); Ito, T.; Tsumura, N.; Shinohara, M.; Ikawa, T. Ikawa, H.; Asano, Y.; Tanaka, Y.; Miyazono, N. [Chiba University, Chiba (Japan); Arita, K.; Moriya, T.; Otsuka, K.; Omura, T. [Hokkaido University, Sapporo (Japan); Kimura, M. [Osaka Prefectural University, Osaka (Japan); Hirata, N. [The University of Tokyo, Tokyo (Japan); Okuike, S.

    1997-05-27

    This is a prompt report. These days the importance of acquiring knowledge about the structure from the lower crust down to the upper mantle is often discussed with reference taken to Hyogo-ken Nanbu Earthquake. The Hidaka collision belt where the lower crust is exposed on the surface is a rare phenomenon in the world and has been the subject of seismic survey. As a part of the survey, experiments are conducted by the use of vibrations produced by Vibroseis and dynamite sources. Every one of the shot records (20-second record) from the two types of vibration sources contains a clear echo in the vicinity of 16 seconds supposedly from a level deeper than 40 kilometers, not to mention reflections from shallow levels. Although some studies have to be conducted before the reflecting geological boundary (possibly the upper mantle) of the echo near the 16-second point can be identified, yet this is probably the reflection from the deepest level ever obtained in the seismic reflection survey conducted in Japan`s land area. It is proved by this experiment that vibration from a vibrator can reach as far as that from explosion if the vibrator specifications are rightly chosen. 4 refs., 3 figs.

  10. Three-dimensional modeling in the electromagnetic/magnetotelluric methods. Accuracy of various finite-element and finite difference methods; Denjiho MT ho ni okeru sanjigen modeling. Shushu no yugen yosoho to sabunho no seido

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, Y. [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1997-05-27

    To enhance the reliability of electromagnetic/magnetotelluric (MT) survey, calculation results of finite-element methods (FEMs) and finite difference methods (FDMs) were compared. Accuracy of individual methods and convergence of repitition solution were examined. As a result of the investigation, it was found that appropriate accuracy can be obtained from the edge FEM and FDM for the example of vertical magnetic dipole, and that the best accuracy can be obtained from the FDM among four methods for the example of MT survey. It was revealed that the ICBCG (incomplete Cholesky bi-conjugate gradient) method is an excellent method as a solution method of simultaneous equations from the viewpoint of accuracy and calculation time. For the joint FEM, solutions of SOR method converged for both the examples. It was concluded that the cause of error is not due to the error of numerical calculation, but due to the consideration without discontinuity of electric field. The conditions of coefficient matrix increased with decreasing the frequency, which resulted in the unstable numerical calculation. It would be required to incorporate the constraint in a certain form. 4 refs., 12 figs.

  11. Growth behavior of alloy layer in hot-dip Zn-5-30 mass% Al-coating; Yoyu Zn-5-30 mass% Al gokin mekki ni okeru gokinso seicho kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Uchida, Y. [Nisshin Steel Co. Ltd., Tokyo (Japan); Yamakawa, K. [University of Osaka Prefecture, Osaka (Japan)

    1995-10-01

    The growth of the alloy layer formed in a hot-dip Zn-5-30 mass%Al coating has been studied by gas-reducing coating and fluxing coating methods. The growth of the alloy layer occurred at a bath temperature above 520{degree}C even in a short time immersion (lass), and is accelerated with increasing the Al content in the bath and raising the bath temperature. The grown alloy layer consists of Al-Fe intermetallic compounds (mainly Al5Fe2 phase containing 6.7-7.8 at%Zn), and Zn phase (94-95 at%Zn) solidified at cavities in Al-Fe intermetallic compounds. In similar to Al5Fe2 phase formed in a hot-dip aluminizing, this Zn-containing Al5Fe2 phase formed in the hot-dip Zn-5-30 mass%Al coating has also a strong orientation of (002) plane and grows even in a vertical direction to the steel surface. However, in the hot-dip Zn-5-30 mass%Al coating, Al-Fe intermetallic compounds grow preferentially at ferrite grain boundaries of the steel substrate where Zn has diffused. It is considered that the grain boundary diffusion of Zn to the steel substrate has a great influence on the growth of the alloy layer. 14 refs., 7 figs., 3 tabs.

  12. Formation of out-burst structure in hot-dip Zn-5mass%Al alloy coating; Yoyu Zn-5mass%Al gokin mekki ni okeru tosshutsuso no keisei kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Uchida, Y.; Ando, A.; Komatsu, A. [Nisshin Steel Co. Ltd., Tokyo (Japan); Yamakawa, K. [University of Osaka Prefecture, Osaka (Japan). College of Engineering

    1998-10-01

    The formation of the `out-burst` products which is consisted of Al-Fe intermetallic compounds (IMCs) grown locally and abnormally, has been studied to compare with the structure of thin alloy layer normally formed on the sheet steel in a hot-dip Zn-5mass% Al alloy coating at the bath temperature of 450degC. The formation of the out-burst products is not due to the localized growth of thin alloy layer consisted of mainly Zn containing Al3Fe(Al13Fe4), but due to the growth of Al-Fe IMCs with mainly Zn containing Al5Fe2 formed at ferrite grain boundaries near the steel surface. These Al-Fe IMCs are considered to be changed from Fe-Zn IMCs which have been formed by the grain boundary diffusion of Zn. And, during changing to Al-Fe IMCs, Zn discharged from Fe-Zn IMCs further diffuses to the adjacent ferrite grain boundaries and also into the adjacent ferrite grains. As a result, Fe-Zn IMCs are formed around Al-Fe IMCs which have been formed at the grain boundaries, and changes again to Al-Fe IMCs. This growth behavior of Al-Fe IMCs formed at the grain boundaries is induced from the results obtained in the previous works that the changing rate from Fe-Zn IMCs to Al-Fe IMCs in a molten Zn-5mass% Al alloy bath at 450degC is very high. 9 refs., 5 figs., 2 tabs.

  13. Study on reservoir behavior based on gravity changes in the Hatchobaru geothermal field; Hacchobaru chinetsu chitai ni okeru juryoku monitoring kekka kara no chinetsu choryuso no kyodo i kansuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tagomori, K.; Nagano, H. [West Japan Engineering Consultants Inc., Fukuoka (Japan); Ehara, S. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Oishi, K. [Kyushu Electric Power Co. Inc., Fukuoka (Japan)

    1996-04-25

    Since extraction of geothermal fluid remarkably increased due to start of commercial operation of Hatchobaru geothermal power plant No.2 unit in 1990, geothermal reservoir behavior was monitored through gravity changes. As a result, Hatchobaru geothermal area was divided into three zones such as northern zone (A), central zone (B) surrounding A zone, and southern zone (C). Gravity increased in A zone as reinjection zone, while decreased in C zone as production zone. Gravity changes relatively well corresponded to pressure changes of the reservoir. Gravity halted to decrease during a period from the middle of 1992 to the beginning of 1993, and at present gravity is nearly constant or increasing. In particular, suspension of a remarkable decrease in gravity around Watarase Jigoku means that geothermal fluid is being supplied to the reservoir through NW-SE fault in the east of Hatchobaru area. The mass balance of Hatchobaru reservoir seems to be stable from the viewpoint of gravity changes. Generally the reservoir has gradually recovered from mass reduction with an increase in gravity since 1993. 5 refs., 11 figs.

  14. Energy recovery and substitute fuel technology in the flash smelting furnace with electrodes (FSFE) at Tamano Smelter. Tamano seirenjo jidenro ni okeru energy kaishu to daitai nenryo gijutsu no kakuritsu

    Energy Technology Data Exchange (ETDEWEB)

    Shibata, T. (Hibi Kyodo Smelting Co. Ltd., Okayama (Japan))

    1990-07-25

    The progress and result of an energy saving technology development associated with the flash smelting furnace with electrodes (FSFE), which is an Outokumpu type flash smelting furnace with electrodes in the settler and using an up-take equipped with a water-cooled jacket, at the Tamano Smelter, a large scale coastal facility, were reported. An energy recovery has been conducted by the recovery of waste heat from the boiler replaced from the water-cooled up-take without increasing temperature in the inlet of boiler, which lead an increase of about 5,000 MWH a year of electric power generation. The fuel mixing combustion and the substitute fuel combustion have been also performed. The fuel was changed from the heavy oil to the pulverized coal, and subsequently, to the coke breeze. The substitution of fuel resulted the decrease of the cost in the electric furnace and the manhour for maintenance as well as the fuel cost. A FSFE operational technology called carbon monoxide concentration control was developed, in which the special qualities of coke could be utilized. Finally, the operational technology without using the electric furnace initially equipped was established. 7 refs., 16 figs., 6 tabs.

  15. Effect of superposing a DC-magnetic field on core loss of Mn-Zn ferrite; Mn-Zn ferrite no core loss ni okeru chokuryu jikai inka no koka

    Energy Technology Data Exchange (ETDEWEB)

    Takadate, K.; Yamamoto, Y.; Makino, A. [Alps Electric Co. Ltd., Tokyo (Japan)

    1998-06-01

    The effects of superposing a DC magnetic field on core loss of Mn-Zn ferrites were investigated. The core losses at 3 MHz are reduced to 56% by superposing a magnetic field of 2kOe perpendicularly to the magnetic path. The reduction of the core losses is mainly resulting from the decrease of the residual loss, which occupies a large part of the core loss at 3MHz. The magnetization of the samples becomes about 80% of the saturation magnetization by applying a magnetic field of 2kOe perpendicularly to the magnetic path. The decrease of the residual losses can be explained by the change of magnetization process from the domain wall displacement to the rotation magnetization with increasing the superposed DC magnetic field. 16 refs., 9 figs., 3 tabs.

  16. Basic investigation on promotion of joint implementation in fiscal 2000. Energy conservation measure project for Ahwaz Steel Complex in Iran; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Iran Ahwaz seitetsusho ni okeru sho energy taisaku jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective to save energy and reduce greenhouse gas emission, a project has been discussed to introduce a gas turbine combined cycle power generation system for effective waste heat utilization and a pellet coating facility into the direct reduction steel making plant of Ahwaz Steel Complex in the Islamic Republic of Iran. The project will have a waste heat boiler installed at the outlet of the MIDREX plant waste heat recovery device to link it with a gas turbine combined cycle power plant to structure a 42-MW power generation system. In addition, productivity enhancement was attempted by applying the raw material pellets with coating to raise the reduction gas blow-in temperature. The energy saving effect expected from this project would be saving of 63,140 tons of crude oil equivalent annually, and the greenhouse effect gas reducing effect would reduce 173,790 t-CO2 annually. Although the investment will require about 3.16 billion yen, the cost reduction amount in association with power generation is small because of the power purchase unit cost being as very low as 1.9 yen/kWh, making the investment recovery period 10.2 years. Therefore, the project will not be realizable economically. (NEDO)

  17. Report on the field test project for wind power development at Shinwa-no-Sato Park (wind characteristics investigation); Shinwa no sato koen ni okeru furyoku kaihatsu field test jigyo (fukyo seisa) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-01

    Wind characteristics are observed for a year at Shinwa-no-Sato Park, Kirishima Town, Aira-gun, Kagoshima Prefecture. The average wind speeds at 20m and 10m above ground are 3.9m/s and 3.3m/s, but they are a little higher in the prevalent directions of east and east-north-east, and are 4.7m/s and 5.5m/s. The annual operation rates of the 150kW, 300kW, and 750kW wind turbine models are 36.0%, 39.1%, and 55.5%. Their annual capacitor ratios are 12.4%, 14.9%, and 15.0%. The annual wind direction occurrence rate on the wind axis is as high as 70.6% in the direction of west, and it should be highly evaluated that turbulence intensity is 0.3 or less in all the directions. As for the surroundings, the observation station is situated in a park which contains no residential zone that may cause noise-related troubles, and possibilities are quite low of difficulties entailing electromagnetic wave emission. Accordingly, wind power development at Kirishima Town is not impossible. But, before a wind power system is actually introduced into the park, it is necessary to select a wind turbine which can operate on low wind speeds of 1-3m/s and can easily connect to the commercial line in the interconnection scheme. (NEDO)

  18. Fiscal 1999 basic survey report for promotion of joint implementation. Study on energy saving and CO2 reduction at Balikpapan refinery; 1999 nendo Balikpapan seiyusho ni okeru shoene CO{sub 2} sakugen chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Concerning the reduction of greenhouse gas emissions for the embodiment of clean development mechanisms (CDMs) in Indonesia, a survey is conducted about energy saving and CO2 reduction at its Balikpapan refinery. At the refinery, a crude-oil atmospheric distillation unit operates at 200,000 BPSD (barrels per stream day) and a vacuum distillation unit at 81,000 BPSD, with the fuel consumed by the two units discharging approximately 470,000 tons/year of CO2. The result of the survey discloses that there is need for some improvement in relation with heat recovery and that the great distance between the two distillation units presents a problem in relation with heat efficiency. To settle the problems, heat recovery will be enhanced and the fuel to be burned in the heating furnace will be reduced. A plan to modify the heat exchanger system is worked out using JGC Corporation's energy-saving technology, and a rough design is drafted for the modification. When the modification is carried out, there will be a CO2 reduction of 18,636-61,597 tons/year. The Pertamina also wants the plan to be realized, wishing that technical and financial aids will be available. The plan when realized will serve as a stimulus to the local community and to the industry as a whole. (NEDO)

  19. Concept of intellectual information tool in petroleum development. Part 2. Develpment of internet and its high-grade utilization; Sekiyu kaihatsu ni okeru chiteki joho tsuru ko. 2. Intanetto no tenkai to sono kodo riyo

    Energy Technology Data Exchange (ETDEWEB)

    Mutsukawa, S. [Tokyo Univ. (Japan). Faculty of Engineering

    1994-06-24

    An internet was originally called Advanced Research Projects Agency Network (ARPANET), and it was mainly a military related network. In 1980s, by an assistance of the National Science Foundation (NSF) the military related parts were cut off, and then the existing networks were taken in one after another, and consequently a basis of the present internet was made. After that the NSF has come to manage a nucleus network, and in addition the further various existing networks were absorbed, and subsequently an internet has been formally started in 1989. Though in the petroleum industry through the oversea business offices of each enterprise an information collection is being performed, in addition to a system so far, a construction of the system to be able to get without omission and simply a political information being transmitted rapidly through the internet from the foreign governments, furthermore the publicized informations of the academic societies and the public service organizations, and so forth will be necessary to be done. A propagation of the internet and its future possibility are mentioned. 1 fig., 1 tab.

  20. Pressure dependence of emission intensity of rare-gas excimer light produced by silent discharge; Teikiatsu ryoiki ni okeru musei hoden reiki ki gas excimer hikari shutsuryoku no atsuryoku izonsei

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, Y.; Tanaka, M.; Yukimura, K. [Doshisha University, Kyoto (Japan)

    1996-09-20

    To establish the pressure dependence of silent discharge excited rare gas excimer light emission, a vacua ultraviolet light was subjected to spectroscopic analysis at a pressure lower than 20kPa. Researches are under way to apply the discharge excited rare gas excimer lamp as a vacuum ultraviolet light source for the development of new materials and for the conservation of environments. When the pressure is as low as 1.8kPa or 4.4kPa, the emission has peaks at wavelengths centering on 147nm and 149nm, both of which are the resonance lines of the xenon atom. Excimer generation becomes prominent as the pressure increases, with the second continuum of light growing dominant at 35kPa to weaken relatively the resonance lines and the first continuum of light. In the first continuum, emission increases only at a suppressed rate, as compared with emission in the second continuum, due for instance to a collision caused relaxation process in which excimers are lost. In the case of xenon in the vicinity of 10-11kPa, the first continuum of light and the second continuum of light are approximately equal in emission intensity, producing a vacuum ultraviolet light source with a bandwidth relatively large for a single gas spectrum. 14 refs., 11 figs.

  1. Ionization current in N2 gas. Part 7. ; Diffusion and reflection of metastable particles. N2 gas chu ni okeru denri denryu. 7. ; Jun antei reiki ryushi no kakusan to hansha

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, S.; Ito, H.; Sekizawa, H. (Chiba Inst. of Technology, Chiba (Japan)); Ikuta, N. (Tokushima Univ., Tokushima (Japan))

    1993-06-20

    The energy loss process in quenching of excited particles by collision to other ones and solid surfaces was investigated with metastable excited particles formed in weakly ionized gases. The measured lifetime of N2 metastable particles in N2, N2/CO, N2/CH3 gases during Townsent discharge did not agree with the Molnar's theoretical value which was obtained by solving diffusion equations using the boundary condition that assumes the density of excited particles to be zero at electrodes and tube walls. Strange behavior was observed too, that is, coefficients of diffusion and reaction rate determined by the theoretical lifetime change systematically with the distance between electrodes. Then, the novel boundary condition that takes reflection coefficient into account was applied to solve diffusion equations. The results obtained could account for experimental results without any discrepancy. The analysis of results clarified the dependence of various parameters of metastable excited particles on the reflection coefficient. The increase of reflection coefficient decreases the surface quenching of excited particles at electrodes and elongs effectively excited lifetime and increases the number of collisional quenching in gas phases. 16 refs., 8 figs.

  2. Determination of electron impact ionization and excitation coefficients in He-Xe gas mixtures. He-Xe kongo gas ni okeru denshi shototsu denri keisu oyobi reiki keisu no sokutei to kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, K.; Tachibana, K. (Kyoto Inst. of Technology, Kyoto (Japan))

    1991-03-20

    The rare gas discharge gives a stable discharge and light emission characteristics at low temperature in comparison with the discharge of the vapor of such a metal as Hg. The present barrier for the commercialization of the color PDP lies in the lower level of its emission intensity and efficiency in comparison with that of CRT. In this report, an electron impact ionization coefficient in a gas mixture and an electron impact excitation coefficient for a XeIs {sub 4} level were analyzed using a Boltzmann equation by means of a steady state Townsend method using a drift tube. By comparing both, the elementary process in the gas mixture is investiagted to discuss the respective contributions for the effective ionization coefficient and the excitation coefficient. As a result, it was found that the ionization process in the He-Xe gas mixture could be described by the processes of direct ionization of Xe and He, and an indirect ionization (Penning effect) by an active helium. 37 refs., 12 figs.

  3. Generation of metallic arc spectrum of pumping discharge of XeCl laser; XeCl ekishima laser reiki hoden ni okeru arc iko to kinzoku supekutoru no hassei

    Energy Technology Data Exchange (ETDEWEB)

    Koike, H.; Yukimura, K. [Doshisha University, Kyoto (Japan)

    1997-12-20

    An arc generation of a long-pulse spiker-sustainer excimer laser with about 250ns of pulse width , is discussed by using time-varying spectroscopic method. First arcing occurs during a main discharge for laser excitation and shows XeII spectrum, while a glow-like discharge represents only XeI spectrum, the metallic spectrum such as Nil caused by vaporization of electrode material begins to appear just after the termination of the main discharge. Second arcing occurs after about 2{mu}s, which brings strong intensity of Nil spectrum. It means that the reignition arc might be produced in a metallic vapor that appears during the main discharge. Accordingly, it is concluded that the reignition arc is inherently metallic, which is different from the main arc with rare gas plasma. 9 refs., 9 figs.

  4. Development and problems on concrete technology in Thailand. Effort toward performance-based design and wastes utilization; Tai ni okeru konkurito gijutsu no katten to kongo no mondai. Seino shosagata sekkei to haikibutsu no riyo eno torikumi

    Energy Technology Data Exchange (ETDEWEB)

    Somnuk, Tangtermsirikul [University Thailand, Bangkok (Thailand)

    1999-03-10

    They explained economic crisis and development trend of concrete technology of Thailand in the back and future problem. They introduced growth (GNP) of the economy from 1989 to 1998, growth of the construction business and the cement production quantity and the cement consumption of the interval. In addition, as a design concept of concreting material, they introduced the utilization of the natural and artificial pozzolans (fly ash, steel slag, silica fume, pumice, metakaolin, etc.) as a utilization of a waste to the concrete, when they considered property and strength of the concrete suitable for the climate of Thailand, and they introduced strength of the concrete using these, etc.. (NEDO)

  5. Survey report for fiscal 1997. Survey on publicity measures for promotion of new energy introduction in Tohoku region; 1997 nendo chosa hokokusho. Tohoku chiiki ni okeru shin energy donyu sokushin koho taisaku chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In order to discuss mainly on publicity measures for how to promote new energy introduction in the Tohoku region, items of information were collected and put into order for the state of utilization of new energies in this region, and fundamental materials were prepared. Facilities having introduced new energies by public bodies in the Tohoku area include the prefectural office buildings, town and village office buildings, schools, community centers, welfare facilities such as aged people's centers and hospitals, sports facilities, parks, sewage treatment plants, and refuse incineration plants. The actual record of the introduction in the Tohoku region shows greater number of cases utilizing natural energies. Utilization of recycled energy and high-efficiency energy such as regional heat supply is less because of fewer number of areas built up densely with buildings and factories, with exception of some cases of utilization by the consumer sector. Introduction of clean energy fueled automobiles is little excepting electric vehicles used by the electric power company. Number of natural gas fueled automobiles that have been introduced is few because the infrastructural build-up has not been advanced in the natural gas supply network. (NEDO)

  6. Fiscal 1994 survey of the base arrangement promotion for foreign coal import. Investigation on the trend of coal demand in Central and South American countries; 1994 nendo kaigaitan kiban seibi sokushin chosa. Chunanbei shokoku ni okeru sekitan jukyu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Focusing on the present status and future of coal demand in Central/South American countries and the coal trade between Central/South American countries and the U.S., the paper described the present status and future of coal demand there and the effects on Japan. Export of Colombian coal will amount to approximately 30-35 million tons in 2000. Venezuelan coal 10-20 million tons. The U.S. imported good-quality general coal low in sulfur content, 3.08 tons from Columbia and 1.39 tons from Venezuela. Coal export from the U.S. to Central/South America was mostly of raw material coal, 5 million tons in 1993 and 5.39 million tons in 1994. General coal was 180,000 tons. The U.S. has no plans of increasing US coal export to Central/South America. But it is safely predicted that Columbia and Venezuela will increase coal export to Europe in the future. It will bring about decrease in export of US coal to Europe, which connects with increasing pressure for the coal trade amount of Japan. 21 figs., 47 tabs.

  7. Reduction of artificial source effect in the high-resolution aeromagnetic survey in the Hanshin region; Hanshin chiiki no komitsudo kuchu jiki tansa ni okeru jinko noise source no eikyo no jokyo

    Energy Technology Data Exchange (ETDEWEB)

    Nakatsuka, T.; Makino, M.; Morijiri, R.; Okuma, S. [Geological Survey of Japan, Tsukuba (Japan)

    1997-05-27

    A high-resolution aeromagnetic survey was carried out in December 1995 on areas from Kobe City to Kyoto City in relation to the Hyogoken-nanbu Earthquake in 1995. It was found in the survey that effects of electric trains driven by direct current and man-made structures cannot be avoided, working as a large noise factor in extraction and analysis of geological information. This paper describes a quantitative analysis on magnetic anomaly suspected to have been caused from artificial sources seen in the magnetic map of the Hanshin area obtained from the above exploration data. The paper also gives considerations on methods to remove the effects therefrom. It then describes a quantitative analysis and the result of attempts on removal of the anomaly, taking up the following factors: (1) distribution of specific and remarkable magnetic anomalies which correspond to railroad positions of the Hanshin Railways running through the Nishinomiya-Toyonaka area, (2) the magnetic anomaly trend in positive and negative pair seen in the seafront area of Kobe City, and (3) typical bipolar isolated type magnetic anomaly in the north-west part of Kobe City. The cause for (1) was loop current flown for the railway operation, that for (2) was man-made structures in the improved seafront area, and that for (3) was a provisionally built metal waste storage yard. 9 figs.

  8. Fiscal 1996 survey for the upgrading of the Asia/Pacific coal development. Survey of the coal infrastructure propagation in Indonesia; 1996 nendo Asia Taiheiyo sekitan kaihatsu kodoka chosa. Indonesia ni okeru sekitan infura seibi chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-01

    Phase 1 survey in fiscal 1996 was conducted based on `Agreement on the comprehensive survey of a coal transportation system in South Sumatra` concluded between NEDO and the Ministry of Mine and Energy in Indonesia. In the survey, conducted were collection of data on coal fields and site surveys, collection of data on inland transportation and site surveys, collection of data on harbors and site surveys, and worked out were a simplified database and a coal transportation plan by optimization of the coal chain system. The area for survey is the periphery of the Musi River of South Sumatra. The results of the simulation by LP models were as follows: When the coal of Bukit Asam coal mine is $25/t in price, only coal of 5500Kcal/kg is profitable, and when $27/t in price, coal of 4500Kcal/kg also becomes profitable. This shows that if the coal is of good quality, it can pay arriving at Suralaya, independent of the distance of transportation. 47 figs., 63 tabs.

  9. Feasibility survey of the environmentally-friendly coal utilization system. Feasibility survey of the environmentally-friendly coal utilization system in Indonesia; Kankyo chowagata sekitan riyo system kanosei chosa. Indonesia ni okeru kankyo chowagata sekitan riyo system kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    With relation to the coal of Indonesia, where the expansion of the use of coal as a substitute for petroleum/plant fuel is aimed at, the paper grasped the situation of coal production/distribution/utilization and environmental problems, and analyzed the situation of the coal utilization/spread by industry including the commercial/residential use. The purpose of the survey is to work out a comprehensive master plan including Japan`s international cooperation for introducing the environmentally-friendly coal utilization system to Indonesia. Coal utilization systems, the introduction of which Indonesia should study in future, were picked up, according to the surveys in fiscal 1993 and 1994. In commercial/residential and small-scale industry sectors, needed is improvement of carbonization technology for production of coal carbonization briquette. Moreover, the introduction of bio-briquette should be studied in the future. In the power generation sector, studies should be made on the introduction of technology for SOx/NOx reduction and technology for coal ash treatment including the effective use of coal ash. For the introduction of coal boilers, the combustion mixed with bagasse, which is abundant in amount, is also necessary. In the coal production sector, coal preparation technology is studied, and a method to select the optimum process was proposed through the simulation. 76 figs., 43 tabs.

  10. Survey report 1998. Survey on actual condition of science parks and similar facilities in Asian countries; 1998 nendo chosa hokokusho. Asia shokoku chiiki ni okeru science park nado no jittai chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Implemented at NEDO, on such technical development issues peculiar to developing nations as are difficult to solve by their research and development ability alone, has been a consistent research cooperation with countries in question, such as installation of plants and research facilities, joint research operation, and training of researchers, while Japanese technological skill and research and development know how are utilized, as the international cooperation projects. In this survey, an actual condition was investigated including potential of science parks and similar facilities in Asian countries (Thailand, Indonesia, Malaysia and India), for the purpose of unearthing the needs, seeds, etc., of the future international research cooperation projects. The parks and facilities selected for the survey are as follows. The Thai technology/science parks are the Thai Science Park and four other parks; the Indonesian technology parks are Bukit Indah Industrial City and eleven other parks; the major Malaysian technology parks are Technology Park Malaysia and fourteen other parks; the major Indian technology parks are Electronics City and fifteen other parks. (NEDO)

  11. Hierarchical NiO Superstructures/Foam Ni Electrode Derived from Ni Metal-Organic Framework Flakes on Foam Ni for Glucose Sensing

    International Nuclear Information System (INIS)

    Highlights: • A novel glucose sensor based on hierarchical NiO superstructures/foam Ni was achieved. • The resulted electrode was fabricated by pyrolyzing NiMOFs on foam Ni. • The carbon frame improved the electrical conductivity of the NiO superstructures/foam Ni electrode. • The as-prepared glucose sensor exhibited an excellent sensitivity, high stability and good selectivity. - Abstract: The detection of glucose has been attracting more and more attention. The present work provided a novel glucose sensor based on hierarchical NiO superstructures/foam Ni electrode. In this strategy, the foam Ni was chosen as a substrate to grow Ni metal-organic frameworks (NiMOFs) via “twin metal source” method, and then the hierarchical NiO superstructures/foam Ni electrode was constructed by pyrolyzing the corresponding NiMOFs/foam Ni electrode for the first time. The preparation process was carefully characterized by scanning electron microscopy, thermogravimetric analysis and X–ray powder diffraction. The results showed the NiMOFs on foam Ni electrode with morphology of the flakes. After the NiMOFs/foam Ni electrode was pyrolyzed, the hierarchical NiO superstructures/foam Ni electrode was formed and the hierarchical NiO superstructures uniformly embedded in three-dimensional carbon frameworks to enhance the electrical conductivity of hierarchical NiO superstructures. The electrocatalytic properties of hierarchical NiO superstructures/foam Ni electrode were investigated by cyclic voltammetry, amperometry and chronoamperometry. The novel glucose sensor showed a reasonable linear range of 0.018–1.2 mM and detection limit of 6.15 μM with a high sensitivity of 395 μA mmol−1. Such good result renders it promising candidate for routine testing

  12. Interdiffusion in the Ni/TD-NiCr and Cr/TD-NiCr systems

    Science.gov (United States)

    Pawar, A. V.; Tenney, D. R.

    1974-01-01

    The diffusion of Ni and Cr into TD-NiCr has been studied over the 900 to 1100 C temperature range. The diffusion couples were prepared by electroplating Cr and Ni on polished TD-NiCr wafers. Concentration profiles produced as a result of isothermal diffusion at 905, 1000, and 1100 C were determined by electron microprobe analysis. The Boltzmann-Matano analysis was used to determine concentration-dependent diffusion coefficients which were found to compare favorably with previously reported values. These data suggest that 2 vol % ThO2 distribution has no appreciable effect on the rates of diffusion in TD-NiCr with a large grain size. This supports the view that an inert dispersoid in an alloy matrix will not in itself lead to enhanced diffusion unless a short-circuit diffusion structure is stabilized.

  13. Research on the summer type wall inside of the body dew in the air-conditioning time (2). Numerical value analysis by the two-dimensional model and precision verification; Reiboji ni okeru natsugataheki tainai ketsuro ni kansuru kenkyu (2). 2 jigen moderu ni yoru suchi kaiseki oyobi keido kensho

    Energy Technology Data Exchange (ETDEWEB)

    Saito, Hiroaki. [Testing Center for Construction Materials. Tokyo (Japan); Tsuchiya, Takao.

    1999-07-01

    The outline could grasp the tendency of every method of construction related to the damp nature of the wall inside of the body part by doing a laboratory experiment for the wall body model in the artificial climate room which reproduced the outside environment of summer. This time, the numerical value calculation which this heat water time movement equation was used for is examined about the action, the utility of the calculation by using the data which could get it more for the actual measurement, and nature of each member which composes a wall body is grasped, and it aims at explaining the mechanism of the summer pattern. As for the influence on a result of a calculation by modeling as well, a consideration is added again. (NEDO)

  14. Studies on the air distribution and thermal performance of the air circulation wall. Part 4. Study on the thermal emissivity of the air circulation layer`s surfaces; Gaidannetsu tsuki koho ni okeru tsuki sonai no netsu tsuki tokusei ni kansuru kenkyu. 4. Tsuki sonai hyomen no hosha tokusei ni kansuru kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kamimori, K.; Sakai, K.; Ishihara, O. [Kumamoto University, Kumamoto (Japan)

    1996-10-27

    The thermal and air distribution characteristics of the air circulation wall in a heat-insulated system were grasped using an experimental model. In this paper, the difference in the heat exchange between the wall and air was confirmed based on the radiation on the circulation layer`s surface. In this system, thin air circulation layers with ventilating holes at the top and bottom are attached to the south and north outer walls of a wooden building. This system is a kind of passive solar house that achieves the insolation screening effect and the temperature rising effect based on solar collection. The heat flow in a circulation layer is eliminated by the natural convection heat transfer on the outer wall. The heat flow passing through insulating materials is the heat transfer by radiation. The heat flow based on the in-layer natural convection is increasingly eliminated by the decrease in temperature on the air circulation layer`s surface. The decrease in room surface temperature using aluminum foil and the reflective heat-insulated effect showed that the heat passing through the wall surface decreases as the convection heat transfer in an air circulation layer increases. 6 refs., 20 figs., 3 tabs.

  15. The Ni-YSZ interface

    DEFF Research Database (Denmark)

    Jensen, Karin Vels

    The anode/electrolyte interface in solid oxide fuel cells (SOFC) is known to cause electrical losses. Geometrically simple Ni/yttria-stabilised zirconia (YSZ) interfaces were examined to gain information on the structural and chemical changes occurring during experiments at 1000°C in an atmosphere...... content (99.8% Ni and 99.995% Ni) were used to examine the impact of impurities on the polarisation resistance and contact area morphology. The electropolished nickel wires were pressed against a polished 8 mol% YSZ surface. Extensive structural changes from a flat interface to a hill and valley structure...

  16. Domain Structures and Anisotropy in Exchange-coupled [Co/Pd]-NiFe and [Co/Ni]-NiFe Multilayers

    Science.gov (United States)

    Tryputen, Larysa; Chung, Sunjae; Mohseni, Majid; Nguyen, T. N. Anh; Åkerman, Johan; Guo, Feng; McMichael, Robert D.; Ross, Caroline A.

    2014-03-01

    Exchange-coupled multilayers [Co/Pd]5-/NiFe and [Co/Ni]4-NiFe with strong perpendicular magnetic anisotropy have been proposed to use in spin-torque switching and oscillators devices with tilted fixed and free layer to improve their functional performance. We present an experimental study of the magnetization behavior of [Co/Pd]5-/NiFe and [Co/Ni]4-NiFe multilayers measured using magnetometry, magnetic force microscopy (MFM) and ferromagnetic resonance (FMR) as a function of the thickness of the top NiFe layer. We varied the thickness of the NiFe layer in [Co/Pd]5-NiFe (t), t = 0 - 80 nm and [Co/Ni]4-NiFe (t), t = 0.5 - 2.5 nm in order to study the interplay between perpendicular magnetization of the Co/Pd or Co/Ni multilayers and in-plane magnetization of the NiFe. Our magnetometry and FMR data suggest that the [Co/Ni]4/NiFe multilayer behaves like a homogeneous ferromagnetic film with anisotropy that reorients towards in-plane as the NiFe thickness increases, whereas the [Co/Pd]5/NiFe multilayer reveals more complex behavior in which the [Co/Pd] layer retains out-of-plane anisotropy while the magnetization of NiFe layer tilts in-plane with increasing thickness. MFM showed that domains with ~0.1 +/-m size were visible in [Co/Pd]-/NiFe with NiFe thickness of 20-80 nm. Multilayers were patterned into sub-100 nm dots using ion beam etching and their magnetization behavior are compared with unpatterned films.

  17. Measurement of 59Ni and 63Ni by accelerator mass spectrometry at CIAE

    Science.gov (United States)

    Wang, Xiaoming; He, Ming; Ruan, Xiangdong; Xu, Yongning; Shen, Hongtao; Du, Liang; Xiao, Caijin; Dong, Kejun; Jiang, Shan; Yang, Xuran; Lan, Xiaoxi; Wu, Shaoyong; Zhao, Qingzhang; Cai, Li; Pang, Fangfang

    2015-10-01

    The long lived isotopes 59Ni and 63Ni can be used in many areas such as radioactive waste management, neutron dosimetry, cosmic radiation study, and so on. Based on the large accelerator and a big Q3D magnetic spectrometer, the measurement method for 59Ni and 63Ni is under development at the AMS facility at China Institute of Atomic Energy (CIAE). By using the ΔE-Q3D technique with the Q3D magnetic spectrometer, the isobaric interferences were greatly reduced in the measurements of 59Ni and 63Ni. A four anode gas ionization chamber was then used to further identify isobars. With these techniques, the abundance sensitivities of 59Ni and 63Ni measurements are determined as 59Ni/Ni = 1 × 10-13 and 63Ni/Ni = 2 × 10-12, respectively.

  18. Ni4Ti3 precipitate structures in Ni-rich NiTi shape memory alloys

    Czech Academy of Sciences Publication Activity Database

    Holec, David; Bojda, Ondřej; Dlouhý, Antonín

    2008-01-01

    Roč. 481, Sp. Iss. (2008), s. 462-465. ISSN 0921-5093. [ESOMAT 2006. Bochum, 10.09.2006-15.09.2006] R&D Projects: GA ČR(CZ) GA106/05/0918 Institutional research plan: CEZ:AV0Z20410507 Keywords : NiTi shape memory alloy s * Ni4Ti3 precipitates * Multi-step martensitic transformations Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.806, year: 2008

  19. Thermodynamic reassessment of Gd–Ni system

    Energy Technology Data Exchange (ETDEWEB)

    Rahou, Z., E-mail: rahou.zakarea@gmail.com; Mahdouk, K.

    2015-11-05

    By means of CALPHAD (CALculation of PHAse Diagrams) approach, the phase diagram and thermodynamic data of the Gd–Ni system were critically assessed. The Gd–Ni system contains four solution phases (liquid, face-centered cubic FCC-A1, body-centered cubic BCC-A2 and hexagonal close-packed HCP-A3) modeled with the Redlich-Kister polynomials and seven intermetallic compounds Gd{sub 3}Ni, GdNi, GdNi{sub 2}, GdNi{sub 3}, Gd{sub 2}Ni{sub 7}, GdNi{sub 5} and Gd{sub 2}Ni{sub 17}, which are all treated as stoichiometric compounds. A set of self-consistent thermodynamic parameters describing various phases in this binary system was obtained. The phase diagram and thermodynamic quantities calculated from assessed parameters agree well with experimental data.

  20. Submicron particles of Co, Ni and Co–Ni alloys

    Indian Academy of Sciences (India)

    P Saravanan; T A Jose; P John Thomas; G U Kulkarni

    2001-10-01

    Magnetic sub-micron sized particles (with diameters in the range 100–600 nm) of Co, Ni and Co–Ni alloys, protected with polyvinylpyrrolidone have been prepared in gram quantities using the polyol process. Experiments carried out with different metal precursors and starting compositions have yielded reliable routes to produce particles of the desired diameters in the 100–600 nm range. The particles were characterized with X-ray diffraction, scanning electron microscopy, energy dispersive X-ray analysis, thermogravimetric analysis and magnetic measurements. The particles are found to be stable under ambient conditions indefinitely. The coercivity values of the Co and Ni particles are ∼ 50% higher compared to the corresponding bulk values. The alloy particles follow a trend similar to the bulk alloys.

  1. Ni putes ni soumises. Media and women with other gender?

    OpenAIRE

    THIÉBLEMONT Sylvie

    2014-01-01

    Since 2000, new women's movements emerge like Ni putes ni soumises (NPNS) who give a new approach to activism: not the one on feminists in the classi- cal sense of the term with the connotations it carries, but women carrying claims in the media and through the media on the living conditions of the residents of the suburbs. So, many media will take part in the mediatization of NPNS and its dis-courses, and will serve in some way as a place of “factory” for the public opinion.

  2. Effects of plate thickness on reverse martensitic transformation of prestrained NiTi/NiTi alloy

    Institute of Scientific and Technical Information of China (English)

    YAN Zhu; CUI Lishan; ZHENG Yanjun

    2007-01-01

    In this Paper, differential scanning calorimeter (DSC)was used to study the effects of predeformation and plate thickness on the reverse martensitic transformation of explosively welded NiTi/NiTi alloy.Results showed that there was a constraint between Ni50.4Ti(NiTi-1)and Ni49.8Ti (NiTi-2),which led to that the thickness of NiTi-1 or NiTi-2 strongly affected the reverse martensitic transformation behavior because residual stress variations in thickness wound enable bias force to be built inside the composite.The DSC measurements showed that after deformation,the reverse martensitic transformation temperature of the composite was increased with the increasing thickness of NiTi-2.Also.the XRD results revealed that the microstructure of NiTi/NiTi alloy changed from B2 phase to B19'phase along the thickness direction.

  3. nière's Disease

    Science.gov (United States)

    ... can control their vertigo with diet, drugs, or devices. However, a small group of people with Ménière’s disease will get relief only by undergoing surgery. What research about Ménière’s ...

  4. Laser welding of TiNi shape memory alloy and stainless steel using Ni interlayer

    International Nuclear Information System (INIS)

    Highlights: ► Laser welding was achieved using Ni interlayer between TiNi SMA and stainless steel. ► Ni interlayer thickness has great effects on joint microstructure and properties. ► Increasing Ni interlayer thickness results in increasing γ-Fe phase in weld metals. ► Excessive addition of Ni results in forming more TiNi3 and pores in the weld metals. ► Suitable Ni interlayer thickness improves the joint quality. -- Abstract: Laser welding of TiNi shape memory alloy wire to stainless steel wire using Ni interlayer was investigated. The results indicated that the Ni interlayer thickness had great effects on the chemical composition, microstructure, gas-pore susceptibility and mechanical properties of laser-welded joints. With an increase of Ni interlayer thickness, the weld Ni content increased and the joint properties increased due to decreasing brittle intermetallic compounds (TiFe2 and TiCr2). The joint fracture occurred in the fusion zone with a brittle intermetallic compound layer. The tensile strength and elongation of the joints reached the maximum values (372 MPa and 4.4%) when weld Ni content was 47.25 wt.%. Further increasing weld Ni content resulted in decreasing the joint properties because of forming more TiNi3 phase, gas-pores and shrinkage cavities in the weld metals. It is necessary to select suitable Ni interlayer thickness (weld composition) for improving the mechanical properties of laser-welded joints.

  5. CONFIGURATION-INTERACTION IN NI METAL AND NI-ALLOYS AND HIGH-ENERGY SPECTROSCOPY

    NARCIS (Netherlands)

    TANAKA, A; JO, T; SAWATZKY, GA

    1992-01-01

    We discuss the electronic state of Ni atoms in Ni metal and of Ni impurity in Cu and Au metals from the viewpoint of 3d configuration interaction (CI) using the Anderson impurity model including atomic multiplets. On the basis of the discussion, we give an interpretation for the Ni 2p-core X-ray pho

  6. Revisiting El Niño Modokis

    Science.gov (United States)

    Marathe, Shamal; Ashok, Karumuri; Swapna, P.; Sabin, T. P.

    2015-12-01

    The suggestion that there exist two types of El Niño in the tropical Pacific has generated a debate in the community. Applying various linear and non-linear approaches and composite analysis technique on observed and reanalyzed climate datasets primarily for the 1950-2010 period, we revisit the variability of the tropical Pacific in the light of this debate. Our objective is to examine whether the proposed El Niño Modokis need a classification distinct from canonical El Niños. Even if the distinction is subject to short data records, we demonstrate that the El Niño Modoki events indeed display a seasonal evolution and teleconnections different from the canonical El Niños, and that the distinction is not subject to inclusion of the two extreme El Niños 1982 and 1997 as canonical El Niños. We show that the El Niño Modoki events are not an artifact associated with the orthogonality constraint associated with the EOF technique. Our cluster analysis shows that evolutions of the canonical El Niño and El Niño Modokis through various seasons differ from one another. Importantly, the dynamic and thermodynamic air-sea coupling strength is distinctly different between the El Niño Modoki and the canonical El Niño events. We find that, dynamic feedback intensity is stronger for El Niño Modoki (canonical El Niño) during boreal summer (winter); though the air-sea coupling strength, a major contributor to Bjerknes feedback, is maximum for Modokis during the developing stages, it decreases thereafter. In case of thermodynamic feedback intensity, SST-wind-evaporation feedback is dominant for El Niños while SST-SHF feedback is important during El Niño Modokis. However, we find that the thermodynamic feedback values significantly differ across the flux datasets.

  7. Density of Liquid Ni-Cr Alloy

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    The density of liquid Ni-Cr alloy was measured by a modified sessile drop method. The density of liquid Ni-Cr alloywas found to decrease with increasing temperature and Cr concentration in the alloy. The molar volume of liquidNi-Cr alloy increases with increasing the Cr concentration in the alloy. The molar volume of Ni-Cr alloy determinedin the present work shows a positive deviation from the linear molar volume.

  8. NiSn and porous NiZn coatings for water electrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Santos, M.B.F.; Peres da Silva, E.; Andrade, R. Jr.; Dias, J.A.F. (Universidade Estadual de Campinas, SP (BR). Lab. de Hidrogenio)

    1992-01-01

    Porous Ni(Zn) coatings are prepared from the electrodeposition of NiZn alloys followed by chemical leaching in KOH solution. A pyrophosphate bath is used to electrodeposit NiSn alloys (14-84 at.% Sn). Polarization curves for hydrogen and oxygen evolution reactions in 28 wt% KOH solutions at 70{sup o}C are presented for selected Ni(Zn) and NiSn coatings. The electrocatalytic activity of a Ni(Zn) porous anode is maintained after 850 h of electrolysis, whereas the NiSn cathode loses its properties. (author).

  9. Recycling Ni from Contaminated and Mineralized Soils.

    Science.gov (United States)

    Rare plant species accumulate potentially valuable concentrations of some metals. Alyssum murale readily accumulates over 2% Ni in aboveground dry matter when grown on Ni-mineralized serpentine soils in Oregon, allowing production of “hay” biomass with at least 400 kg Ni ha-1 with low levels of fer...

  10. Reaction of amorphous Ni-W and Ni-N-W films with substrate silicon

    Science.gov (United States)

    Zhu, M. F.; Suni, I.; Nicolet, M.-A.; Sands, T.

    1984-01-01

    Wiley et al. (1982) have studied sputtered amorphous films of Nb-Ni, Mo-Ni, Si-W, and Si-Mo. Kung et al. (1984) have found that amorphous Ni-Mo films as diffusion barriers between multilayer metallizations on silicon demonstrate good electrical and thermal stability. In the present investigation, the Ni-W system was selected because it is similar to the Ni-Mo system. However, W has a higher silicide formation temperature than Mo. Attention is given to aspects of sample preparation, sample characterization, the interaction between amorphous Ni-W films and Si, the crystallization of amorphous Ni(36)W(64) films on SiO2, amorphous Ni-N-W films, silicide formation and phase separation, and the crystallization of amorphous Ni(36)W(64) and Ni(30)N(21)W(49) layers.

  11. Strukturelle studier av deuterider for Y3Ni6Al2, LaNiSn og NdNiSn

    OpenAIRE

    2007-01-01

    I det foreliggende hovedfagsarbeidet er hydrider av tre intermetalliske faser; Y3Ni6Al2, LaNiSn og NdNiSn studert med hensyn på strukturkjemi og absorpsjon-desorpsjon egenskaper. Arbeidet med Y3Ni6Al2 og dets deuterider viste seg å bli vanskelig da det forelå ett to-fase produkt.. Relative akselengder for de to fasene (med antatt formel Y3Ni6Al2D9) etter raffinering av PND data tilsier at det kan være noe galt med de foreslåtte modellene i forhold til deres enhetscellevolum og deuterium...

  12. Structural evaluation and nonlinear optical properties of Ni/NiO, Ni/NiCo2O4 and Co/Co3O4 nanocomposites

    International Nuclear Information System (INIS)

    Nanocomposites of Ni/NiO, Ni/NiCo2O4 and Co/Co3O4 have been synthesized by a chemical reduction technique. X-ray diffraction (XRD) and transmission electron microscopy (TEM) images confirm the mixed composite nature of the sample and uniform particle size of approximately 13 nm. Formation of Ni/NiCo3O4 solid solution or NiCo2O4 spinel phase in the mixed composite is confirmed by energy dispersive X-ray (EDX) spectrum. Magnetic hysteresis (M–H) curves of the nanocomposites show excellent ferromagnetic (FM) nature at room temperature. Nonlinear optical transmission of the nanocomposites is measured using the open aperture Z-scan technique employing 7 nanosecond laser pulses at 532 nm. Experimental results show that NiO/NiO–Co3O4/Co3O4 nanocomposites exhibit good optical limiting performance. From the measurements and numerical fitting of the data to theory, it is found that nonlinear absorption has contributions from excited state absorption and two-photon absorption. Optical limiting is enhanced in Co3O4 and Ni/NiCo2O4 in which the Co3O4 content has a larger volume ratio.

  13. First-principles calculations for the elastic properties of Ni-base model superalloys:Ni/Ni_3Al multilayers

    Institute of Scientific and Technical Information of China (English)

    Wang Yun-Jiang; Wang Chong-Yu

    2009-01-01

    A model system consisting of Ni[001](100)/Ni_3Al[001](100)multi-layers are studied using the density functional theory in order to explore the elastic properties of single crystal Ni-based superalloys. Simulation results are consistent with the experimental observation that rafted Ni-base superalloys virtually possess a cubic symmetry. The convergence of the elastic properties with respect to the thickness of the multilayers are tested by a series of multilayers from 2γ'+2γto 10γ'+10γ atomic layers. The elastic properties axe found to vary little with the increase of the multilayer's thickness. A Ni/Ni_3Al multilayer with 10γ'+10γatomic layers(3.54 nm)can be used to simulate the mechanical properties of Ni-base model superalloys. Our calculated elastic constants, bulk modulus, orientation-dependent shear modulus and Young's modulus. as well as the Zener anisotropy factor are all compatible with the measured results of Ni. base model superalloys R1 and the advanced commercial superalloys TMS-26.CMSX-4 at a low temperature. The mechanical properties as a function of the γ' phase volume fraction are calculated by varying the proportion of theγ andγ'phasein the multilayers. Besides, the mechanical properties of two-phase Ni/Ni_3A1 multilayer call be well predicted by the Voigt-Reuss-Hill rule of mixtures.

  14. Flowsheet for 63Ni production

    International Nuclear Information System (INIS)

    The production of large quantities of high specific activity 63Ni (>10Ci/g) requires both a highly enriched 62Ni target and a long irradiation period at high neutron flux. Trace impurities in the nickel and associated target materials are also activated and account for a significant fraction of the discharged activity and essentially all of the gamma activity. While most of these undesirable activation products (mainly transition metals) can be easily removed as chloride complexes during anion exchange, chromium, present as 51Cr, and manganese, present as 54Mn, are exceptions and require solvent extraction of the in-cell product to achieve the desired purity. In addition to summarizing the current development and production experience, optimized flowsheets are discussed

  15. FY 2000 Report on the results of the research work on the development trends of natural gas conversion technologies into liquefied fuel in Russia; 2000 nendo Roshia ni okeru tennen gas no ekitai nenryoka gijutsu no kaihatsu doko nado ni kansuru chosa kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 2000 results of the experimental studies on making Fischer-Tropsch (FT) synthesis catalysts on a trial basis and their commercialization feasibility, aimed at producing liquefied fuels in Russia. Irkutsk State University is developing the 'Fischer-Tropsh synthesis catalysts for motor fuel production.' It is found that n-alkanes as the diesel fuel component is formed on the Co-{gamma}-Al{sub 2}O{sub 3} catalyst improved mainly by the first transition metals. Possibility is demonstrated that the synthesis gas can be directly converted into the hydrocarbons containing a high proportion of isoalkanes by the process which uses a combination of FT synthesis catalyst and zeolite catalyst. Topchiev Institute of Petrochemical Synthesis is developing the 'catalysts for synthesis of fuel hydrocarbons from the nitrogen-diluted synthesis gas.' It is confirmed by the FT synthesis reaction test with the diluted synthesis gas as the starting material that the fused iron and zeolite components for the binary catalyst, selected as the promising catalyst for production of gasoline fuel, are stable for extended periods of 3 months or longer. (NEDO)

  16. Study of coherent optical fiber communication in electromagnetic field. 3. Measurement of transient state of polarization in actual OPGW caused by lightning; Coherent hikaritsushin eno denjikai no eikyo to taisaku. 3. Jitsu field no OPGW ni okeru rakurai ni yoru henpa hendo no sokutei

    Energy Technology Data Exchange (ETDEWEB)

    Kurono, M.; Isawa, K.; Kuribata, M. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1995-03-01

    Coherent optical fiber communication method is effective for increase of transmission capacity of existing optical fiber. But it needs a control of polarization state of optical signal. Especially through OPGW (Optical fiber composite Ground Wire), the polarization state will be influenced by lightning. This report describes a field measurement of optical polarization characteristics in actual OPGW of Hokuriku electric company in the condition of lightning. Main results are follows; (1) In normal condition without lightning, the states of optical polarization have alternative fluctuations of 60Hz. (2) In lightning weather, the transients of optical polarization are detected 51 times in two half months. It is made clear that these transient states are due to lightning by checking the time of day with the time data of LLS (Lightning Location System) and with the time of power line trip. (3) By estimating the waves of polarization shift, the duration of transient is 2 - 5msec, the rise time is 50 - 200usec. and wave tail has damping oscillation of 2 - 5kHz. The maximum shift of polarization states on Poincare sphere is 165 degree, which means polarization changes almost opposite states. (4) By evaluating the locations of lightning with LLS data, the transient polarization shift is caused by lightning over 50 km from observed OPGW. And the short distance tends to the large fluctuation of polarization. This characteristics may have a possibility of application to lightning monitoring. 7 refs., 22 figs., 1 tab.

  17. Recent energy situation in the U.S. and Europe. Trend of discussions on energy safety security and energy policies in the E.U. and CIS (commonwealth of independent states) countries; Obei ni okeru saikin no energy jijo. Energy anzen hosho ni kansuru giron no doko to EU oyobi CIS shokoku no energy seisaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The E.U. intends to establish the stabilized new partnership and economic area, based on free trades and tighter economic cooperation with Mediterranean countries. For the purpose of establishing the effective cooperative relationship in the energy field, the E.U. committee taking the short- and medium-term initiative prepares as follows: The establishment of the European/Mediterranean Energy Forum is thought of. This is for the joint management of cooperation in the energy field and the organization of the conferences and meetings of information exchanges between partners. The discussion is started for the final joining in the organization of partners of Mediterranean countries who do not participate in the Pan-European Energy Charter conference. They study options adoptable for easing investments. They cooperate with the related countries for carrying out the project having common interest in the TENs (Trans-European energy networks) field. The working-out of plans and projects is promoted for coordinating energy projects according to the purposes and procedures of MEDA. 59 refs.

  18. Investigation of the creation of functional surfaces and the recent development in related researches. 2. Investigation of the development of new isolation/refining systems in water system; Kokino hyomen no sosei to shintenkai no kenkyu doko chosa. 2. Suikei ni okeru atarashii bunri seisei system no kaihatsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Propositions were made concerning new chromatography and membrane separation techniques wherein a command control material is used, the mobile phase is fixed upon water, and the fixed phase is caused to vary by external commands, and how to develop the said techniques into a project was discussed. New methods were also introduced, capable of separating water systems and, particularly, capable of separating and refining, without damaging their functions, bionic elements such as proteins, genes, and cells, which encouraged discussion on the future of the said project. As for command controlled materials, detailed investigations were conducted into materials responsive to physical stimulation such as light, electric field, magnetic field, or heat and materials responsive to PH and chemical or biochemical substances, and discussion was made on the structures and characters of the said materials. Concerning the manufacture of a command controlled surface, consideration centered particularly about the density and thickness of command controlled molecules to be introduced onto the surface. Furthermore, the current state and problems were discussed regarding chromatographic separation and refining of optical isomers, nucleic acids, physiologically active substances, peptides, cells, etc. 252 refs., 75 figs., 31 tabs.

  19. Manufacturing facilities of pharmaceutical products and measures for purification of its environment. On the consideration and several utilization of bioburden in the environmental area for pharmaceutical related plants; Iyakuhin no seizo shisetsu to kankyo seijoka taisaku. Yakuji kanren seihin no seizo kankyo ni okeru baio baden no kangaekata to sono riyo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Ishizeki, C. [Yokohama National Univ. (Japan). Faculty of Engineering

    1994-07-31

    The expression, bioburden, is used by many organizations such as WHO and ISO in the field of pharmaceutical related products and is defined as the number and kind of microorganisms which exist as suspended bacteria attached to the object or in an area under the condition close to the nature. In case when this word is used as a nonexperimental element, in the area of production environment, the measurement of the number and kind of microorganisms related there becomes the main concern and in case when the word is used as the element of experiment, test and research, it is utilized in sterilization, sterile filtration, etc. as microorganism load. This article is a general review with occasional insertion of the author`s own views on the concept and utilization concerning bioburdens in the production environment of pharmaceutical related products (medicine, tool for medical treatment, cosmetics, etc.) and explanation is given on the concept and meaning of bioburden grasping of the current state of bioburden and its analysis, general idea to be borne in mind in measuring bioburden, bioburden and its background, importance of bioburden and measures to cope with internationalization. 15 refs., 1 fig., 5 tabs.

  20. Development of [l brace]100[r brace] texture in silicon steel sheets by isothermal austenite[yields]ferrite transformations and its mechanism. Keiso kohan ni okeru toon [gamma][yields][alpha] hentai ni yoru [l brace]100[r brace] shugo soshiki no keisei to sono kiko

    Energy Technology Data Exchange (ETDEWEB)

    Tomida, T. (Sumitomo Metal Industries Ltd., Osaka (Japan). Advanced Technology Research Lab.); Tanaka, T. (Sumitomo Metal Industries Ltd., Osaka (Japan). Iron and Steel Research Lab.)

    1993-12-01

    The texture in silicon steel sheets has been studied during this half of century and the methods for forming the textures suitable as the soft-magnetic materials of [l brace]110[r brace][l angle]001[r angle] as well as [l brace]100[r brace][l angle]001[r angle] have been found. However, few researches has been carried out on the silicon steel using positively the innate properties of the steel such as the transformation between the austenite ([gamma]) and [alpha]-ferrite and the recrystallization in the coexisting area of [alpha]/[gamma] duplex. In this study, the isothermal [alpha][yields][gamma] transformation during the process of vacuum-annealing and decarburizing-annealing of 2% silicon steel containing carbon and Mn and the texture formation accompanied therewith are examined. The conclusions are as follows. The isothermal [alpha][yields][gamma] transformation occurs in the layer just below the surface and the structure of the surface becomes the single phase of [alpha]-ferrite in the vacuum of 10[sup -3]Pa and the temperature is kept constant within the range of [alpha]/[gamma] duplex temperature or [gamma]-phase temperature as from 850 to 1050 centigrade. This surface structure develops to the strong [l brace]100[r brace] texture. 12 refs., 8 figs., 2 tabs.

  1. Survey report for fiscal 1997 on the survey report on the actual state of technical cooperation on industrial technologies by European countries in the South-eastern Asian region; 1997 nendo Tonan Asia chiiki ni okeru Obei shokoku no sangyo gijutsu ni kansuru gijutsu kyoryoku jittai chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The actual state was surveyed on the technical cooperation by European countries in the South-eastern Asian region. The U.S.A. is making research cooperation with Thailand on ethylene molecule structures to enhance productivity in rubber production, France on molecule markers for high production rubber clone selection, and Australia on grain storing and drying methods. For the Philippines, America is giving assistance on management of reproducible resources, France on climate information communications systems for local areas, Australia on grain storing and drying methods, and Germany on waste oil recovery and reutilization, and development of pollution-free energy resources. For Malaysia, the Great Britain is cooperating on building engineering research centers, Australia on search for plant patheology genetic organics available in the Pacific region, and Germany on investigative researches on pollution prevention for tin mines and processing areas, and forestry and plant information systems. With respect to the ASEAN, this paper reports its activities placing importance on biology and electronics engineering, while the organization is taking actions in the areas of foodstuffs, animals, electronics, information and material science, energy exploration, marine and earth physics, and resource development. (NEDO)

  2. Survey report for fiscal 1998. Survey of the current state and tasks of research and development of technologies for effectively utilizing CO{sub 2} fixation by higher vegetation; 1998 nendo chosa hokokusho. Koto shokubutsu ni okeru nisanka tanso koteika yuko riyo gijutsu no kenkyu kaihatsu no genjo to kadai ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Investigations and studies are conducted seeking for a CO2 fixation method improved by utilizing the photosynthesizing function of higher vegetation. Details of higher vegetation genes are being disclosed thanks to the rapid progress of studies making use of molecular biological techniques, and the application of the genetic mechanism to scientific and technological fields is becoming increasingly feasible. In particular, the role of the CO2 fixation enzyme RuBisCO has been elucidated almost completely. It has been learned that, in terms of photosynthesizing capability, the C{sub 4} plants (corn etc.) are 2-3 times higher than the C{sub 3} plants (rice, wheat, etc.), and 5-10 times higher than the CAM plants (cactuses etc.). Studies are also under way about the rice genome so that a photosynthesizing capability so high as that of the C{sub 4} plants may be endowed the rice plant. The metabolism and control of useful substances produced in the CO2 fixation process etc. in the higher vegetation are being investigated, and it is now expected that some day such useful substances will be produced and utilized efficiently. Researches are under way into the relationship between the green leaf that is the organ that performs photosynthesis and the organ (sink) that stores and utilizes starch and sugar is in progress, and now a new field is going to open where vegetables will be fully utilized. (NEDO)

  3. Combustion-driven oscillation in a furnace with multispud-type gas burners. 4th Report. Effects of position of secondary air guide sleeve and openness of secondary air guide vane on combustion oscillation condition; Multispud gata gas turner ni okeru nensho shindo. 4. Nijigen kuki sleeve ichi oyobi nijigen kuki vane kaido no shindo reiki ni oyobosu eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Akiyama, I.; Okiura, K.; Baba, A.; Orimoto, M. [Babcock-Hitachi K.K., Tokyo (Japan)

    1994-07-25

    Effects of the position of a secondary air guide sleeve and the openness of a secondary air guide vane on combustion oscillation conditions were studied experimentally for multispud-type gas burners. Pressure fluctuation in furnaces was analyzed with the previously reported resonance factor which was proposed as an index to represent the degree of combustion oscillation. As a result, the combustion oscillation region was largely affected by both position of a guide sleeve and openness of a guide vane. As the openness having large effect on the ratio of primary and secondary air/tertiary air and the position hardly having effect on the ratio were adjusted skillfully, the burner with no combustion oscillation region was achieved in its normal operation range. In addition, as the effect of preheating combustion air was arranged with a standard flow rate or mass flow flux of air, it was suggested the combustion oscillation region due to preheating can be described with the same manner as that due to no preheating. 5 refs., 8 figs.

  4. Study of thermal threshold and counter-measures for human body in oceanic working environment. 1st Report. Heat balance model and heat storage index; Shonetsu kankyoka no kaiyo sagyo ni okeru netsuteki genkai to onnetsu taisaku ni kansuru kenkyu. 1. Netsu shushi model to onnetsu shisu

    Energy Technology Data Exchange (ETDEWEB)

    Fukuchi, N. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Nakamura, M. [Tokyo Gakugei University, Tokyo (Japan); Murayama, M.

    1996-12-31

    Identification was intended on effects of such thermal factors as metabolic amount, environmental temperature and humidity, and clothing resistance on human body temperatures during works under hot environments. Therefore, measurements were carried out on human skin temperatures, rectum temperatures and humidity inside clothing, while amount of motion, environmental temperature, and clothing are changed in a constant temperature room and under a sun irradiation environment. Furthermore, a heat balance model was prepared, which divides the objects into an outer shell layer whose temperature changes depending on the result of this experiment and into a core having constant temperature characteristics. An equation to derive skin temperatures was introduced from the model. The equation formulated a calculation formula for heat accumulation in human body, which can be used as a hot heat index. Relationship between thermal factors and heat storage amount was investigated to consider a thermal limit for a physical work. An equation to derive skin temperatures was confirmed capable of expressing general change in skin temperatures, being proved by comparison with experiments. Calculation formulas for amount of heat stored in human body were shown capable of expressing influence of different thermal factors, the expression being useful as a hot heat index. Calculating the human body heat storage is very largely affected by effect of sweat to dissipate heat, hence it is necessary to improve the accuracy including that for body temperature adjusting reactions. 17 refs., 17 figs., 5 tabs.

  5. Experimental study of friction of tapered surfaces in keyless propeller. 2{sup nd} report. Effects of taper machining error and surface roughness; Keyless propeller ni okeru taper sesshokumen no masatsu ni kansuru-jikken. 2: taper kako gosa oyobi hyomen arasa no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Kawazoe, T.; Ura, A.; Nakashima, A. [Nagasaki Univ. (Japan)] Nishikido, S. [Mitsubishi Heavy Industries Ltd., Nagasaki (Japan). Nagasaki Shipyard and Engine Works

    1997-12-01

    About 25 years have passed since the development of the keyless propeller, however, recently, torque slip problem is cause in keyless propeller. In the previous report, from one of this factor, experiment was carried out concentrating on the friction behavior at elasto-plastic deformation region. This time, effect of taper machining error and surface roughness, that are the problems while manufacturing keyless propeller and axes on the friction behavior of taper contact surface was studied using a new grip coefficient. As a result, the friction behavior (specially the grip coefficient) during the pushing of keyless propeller was effected greatly by the taper machining error rather than surface roughness and the precision of the taper machining of axis and boss become important. Further, taper machining error is not considered in the design calculation of push-up distance, therefore, if low grip coefficient region is caused in push-up operation, it is preferred that push-up must be carried out up to the decided push-up distance excluding this. These were the clarified things. 6 refs., 10 figs.

  6. Effects of glucose concentration, medium osmotic pressure and light intensity on the growth of Marchantia paleacea var. diptera cells in photomixotrophic culture; Hikari kongo eiyo baiyo ni okeru futaba zenigoke saibo no zoshoku ni oyobosu glucose nodo, baichi shintoatsu to hikari kyodo no koka

    Energy Technology Data Exchange (ETDEWEB)

    Kinooka, M.; Miyaoka, M.; Taya, M.; Tone, S. [Osaka University, Osaka (Japan); Ono, K. [Kumamoto University, Kumamoto (Japan)

    1997-07-10

    Batch cultures of photomixotrophic cells of Marchantia paleacea var. diptera were conducted at 25degC under the initial conditions of glucose concentration of 20 or 40 kg/m{sup 3}, medium osmotic pressure of 520 or 830 kPa and mean incident light intensity of 0, 13 or 28 W/m{sup 2}. The glucose concentration, osmotic pressure and mean light intensity in medium declined with increasing cell mass concentration, so that they became limiting factors against the cell growth during the cultures. A kinetic expression for the cell growth was presented by considering the effects of three limiting factors, and applied to the data obtained from the batch cultures. The calculation results fitted closely with the experimental data in the cultures. 8 refs., 2 tabs., 1 tab.

  7. Manufacture of Raney Ni catalyst with metastable Ni2Al3 by high—energy milling

    Institute of Scientific and Technical Information of China (English)

    滕荣厚; 马如璋; 等

    1999-01-01

    The Ni-Al alloy containing Cr,Fe additives were prepared as Raney Ni Catalyst by high energy milling.The size and surface state of Ni-Al alloy powder were studied by particle size analyzer and sanning electron microscopy.the Structure was analyzed by XRD and Moessbauer methods.The results showed that after a high-energy milling(HEM).the Ni-Al alloy transforms to a nano-scale NiAl structure with rich Al.By annealing the alloy,a metastable Ni2Al3 phase can be obtained.

  8. Manufacture of Raney Ni catalyst with metastable Ni2Al3 by high-energy milling

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    The Ni-Al alloy containing Cr, Fe additives were prepared as Raney Ni catalyst by high energy milling. The size and surface state of Ni-Al alloy powder were studied by particle size analyzer and sanning electron microscopy, the structure was analyzed by XRD and Mossbauer methods. The results showed that after a high-energy milling (HEM), the Ni-Al alloy transforms to a nano-scale NiAl structure with rich Al. Byannealing the alloy, a metastable Ni2Al3 phase can be obtained.

  9. Exclusive study of Ni+Ni and Ni+Au central collisions: phase coexistence and spinodal decomposition; Etude exclusive des collisions centrales Ni+Ni et Ni+Au: coexistence de phase et decomposition spinodale

    Energy Technology Data Exchange (ETDEWEB)

    Guiot, B

    2002-12-01

    The INDRA multidetector allowed us to study the Ni+Ni collisions at 32A MeV and the Ni+Au collisions at 52,4 MeV. Central collisions leading to 'quasi-fused' systems were isolated using multidimensional analysis techniques: the Discriminant Analysis and the Principal Component Analysis. Comparison with a statistical model shows that the selected events are compatible with thermodynamical equilibrium. The average thermal excitation energy is 5A MeV for both systems. Calculations of heat capacities show that the deexcitation of the hot sources are akin to a liquid-gas phase transition of nuclear matter. Indeed heat capacities exhibit a negative branch as expected for a phase transition of a finite system. The dynamics of this phase transition has been investigated by applying the charge correlation method. An enhanced production of events with equal-sized fragments has been evidenced for Ni+Au at 52A MeV. No signal was found for Ni+Ni at 32A MeV. Finally this method was improved by taking into account the total charge conservation. The signal is seen more clearly for Ni+Au at 52A MeV, but is ambiguous for Ni+Ni at 32A MeV. The path followed in the state diagram, or the involved time scales, seem to be different for these systems. (authors)

  10. Measured Activities of Al and Ni in gamma-(Ni) and gamma'-(Ni)3Al in the Ni-Al-Pt System

    Science.gov (United States)

    Copland, Evan

    2007-01-01

    Adding Pt to Ni-Al coatings is critical to achieving the required oxidation protection of Ni-based superalloys, but the nature of the Pt effect remains unresolved. This research provides a fundamental part of the answer by measuring the influence of Pt on the activities of Al and Ni in gamma-(Ni), gamma prime-(Ni)3Al and liquid in the Ni-Al-Pt system. Measurements have been made at 25 compositions in the Ni-rich corner over the temperature range, T = 1400-1750 K, by the vapor pressure technique with a multiple effusion-cell mass spectrometer (multi-cell KEMS). These measurements clearly show adding Pt (for X(sub Pt) less than 0.25) decreases a(Al) while increasing a(Ni). This solution behavior supports the idea that Pt increases Al transport to an alloy / Al2O3 interface and also limits the interaction between the coating and substrate alloys in the gamma-(Ni) + gamma prime-(Ni)3Al region. This presentation will review the progress of this study.

  11. Comparison of the thermal stabilities of NiSi films in Ni/Si, Ni/Pd/Si and Ni/Pt/Si systems

    CERN Document Server

    Wang, R N

    2003-01-01

    The effects of different interlayer materials (Pd and Pt) deposited between Ni films and Si substrates on the NiSi thermal stability are discussed. Ni sub 0 sub . sub 9 sub 4 sub 3 Pd sub 0 sub . sub 0 sub 5 sub 7 Si and Ni sub 0 sub . sub 9 sub 4 sub 5 Pt sub 0 sub . sub 0 sub 5 sub 5 Si solid solutions were formed when the samples were annealed at high temperatures and the lattice parameters of Ni sub 0 sub . sub 9 sub 4 sub 3 Pd sub 0 sub . sub 0 sub 5 sub 7 Si were calculated according to Vegard's law. The NiSi thermal stability was enhanced by interposing a Pd or Pt interlayer, and the sample with the Pt interlayer had the highest NiSi thermal stability among all the samples studied. This is attributed to the reduction of the interface energy between NiSi and Si substrates and the decrease of the driving force for the nucleation of NiSi sub 2 , induced by formation of the NiSi(200) preferred orientation and the solid solution respectively.

  12. Magnetic Properties of Grain Boundaries of Nanocrystalline Ni and of Ni Precipitates in Nanocrystalline NiCu Alloys

    Energy Technology Data Exchange (ETDEWEB)

    Wolf, H.; Guan, Z.; Li, X.; Wichert, Th. [Universitaet des Saarlandes, Technische Physik (Germany)

    2001-11-15

    Perturbed {gamma}{gamma}-angular correlation spectroscopy (PAC) was used to investigate nanocrystalline Ni and NiCu alloys, which are prepared by pulsed electrodeposition (PED). Using diffusion for doping nanocrystalline Ni with {sup 111}In four different ordered grain boundary structures are observed, which are characterized by unique electric field gradients. The incorporation of {sup 111}In on substitutional bulk sites of Ni is caused by moving grain boundaries below 1000 K and by volume diffusion above 1000 K. The nanocrystalline NiCu alloys prepared by PED are microscopically inhomogeneous as observed by PAC. In contrast, this inhomogeneity cannot be detected by X-ray diffraction. The influence of the temperature of the electrolyte, the current density during deposition, and the optional addition of saccharin to the electrolyte on the homogeneity of nanocrystalline NiCu alloys was investigated.

  13. Ultrafast Alkaline Ni/Zn Battery Based on Ni-Foam-Supported Ni3S2 Nanosheets.

    Science.gov (United States)

    Hu, Pu; Wang, Tianshi; Zhao, Jingwen; Zhang, Chuanjian; Ma, Jun; Du, Huiping; Wang, Xiaogang; Cui, Guanglei

    2015-12-01

    Self-supported Ni3S2 ultrathin nanosheets were in situ formed by direct sulfurization of commercially available nickel foam using thioacetamide as sulfur source under hydrothermal process. The morphology and structure of the as-obtained sample were analyzed by using XRD, XPS, SEM, and TEM, revealing that an ultrathin nanosheets Ni3S2 were grown on the surface of Ni form. The as-obtained Ni3S2/Ni composite with uniform architecture was used as cathode material for alkaline Ni/Zn battery, which delivered high capacity of 125 mAh g(-1) after 100 cycles with no obvious capacity fading, extraordinary rate capability (68 mAh g(-1) at the current density of 5.0 A g(-1)), and high operating voltage (1.75 V). PMID:26599523

  14. Magnetic Properties of Grain Boundaries of Nanocrystalline Ni and of Ni Precipitates in Nanocrystalline NiCu Alloys

    International Nuclear Information System (INIS)

    Perturbed γγ-angular correlation spectroscopy (PAC) was used to investigate nanocrystalline Ni and NiCu alloys, which are prepared by pulsed electrodeposition (PED). Using diffusion for doping nanocrystalline Ni with 111In four different ordered grain boundary structures are observed, which are characterized by unique electric field gradients. The incorporation of 111In on substitutional bulk sites of Ni is caused by moving grain boundaries below 1000 K and by volume diffusion above 1000 K. The nanocrystalline NiCu alloys prepared by PED are microscopically inhomogeneous as observed by PAC. In contrast, this inhomogeneity cannot be detected by X-ray diffraction. The influence of the temperature of the electrolyte, the current density during deposition, and the optional addition of saccharin to the electrolyte on the homogeneity of nanocrystalline NiCu alloys was investigated.

  15. Investigation of the porous nanostructured Cu/Ni/AuNi electrode for sodium borohydride electrooxidation

    International Nuclear Information System (INIS)

    An electrochemical approach to nanostructured Cu/Ni/AuNi catalyst design using the electrodeposition process followed by galvanic replacement technique is presented. The procedure consisted of the electrodeposition of Ni–Zn on the Ni coating with subsequent replacement of the zinc by gold at open circuit potential in a gold containing alkaline solution. The surface morphologies and compositions of coatings were determined by energy dispersive X-ray and scanning electron microscopy techniques. The results showed that the Cu/Ni/AuNi coatings were porous composing of discrete Au nanoparticles. The electrocatalytic activity of Cu/Ni/AuNi electrodes for sodium borohydride electro-oxidation was studied using cyclic voltammetry, chronoamperometry, chronopotentiometry and electrochemical impedance spectroscopy techniques. The electro-oxidation current on Cu/Ni/AuNi catalyst is much higher than that on flat Au catalyst. The onset potential and peak potential on Cu/Ni/AuNi catalysts are more negative than that on flat Au catalyst for borohydride electrooxidation. The impedance behavior also shows different patterns, capacitive, and negative resistances and inductive loops at different applied anodic potentials. All results show that the Cu/Ni/AuNi catalysts can be applied as potential anode catalysts for the direct borohydride fuel cells

  16. The impact of Ni on the physiology of a Mediterranean Ni-hyperaccumulating plant.

    Science.gov (United States)

    Roccotiello, Enrica; Serrano, Helena Cristina; Mariotti, Mauro Giorgio; Branquinho, Cristina

    2016-06-01

    High nickel (Ni) levels exert toxic effects on plant growth and plant water content, thus affecting photosynthesis. In a pot experiment, we investigated the effect of the Ni concentration on the physiological characteristics of the Ni hyperaccumulator Alyssoides utriculata when grown on a vermiculite substrate in the presence of different external Ni concentrations (0-500 mg Ni L(-1)). The results showed that the Ni concentration was higher in leaves than in roots, as evidenced by a translocation factor = 3 and a bioconcentration factor = 10. At the highest concentration tested (500 mg Ni L(-1)), A. utriculata accumulated 1100 mg Ni per kilogram in its leaves, without an effects on its biomass. Plant water content increased significantly with Ni accumulation. Ni treatment did not, or only slightly, affected chlorophyll fluorescence parameters. The photosynthetic efficiency (FV/FM) of A. utriculata was stable between Ni treatments (always ≥ 0.8) and the photosynthetic performance of the plant under Ni stress remained high (performance index = 1.5). These findings support that A. utriculata has several mechanisms to avoid severe damage to its photosynthetic apparatus, confirming the tolerance of this species to Ni under hyperaccumulation. PMID:26983814

  17. Investigation on the Interactions of NiCR and NiCR-2H with DNA

    Science.gov (United States)

    Chitranshi, Priyanka; Chen, Chang-Nan; Jones, Patrick R.; Faridi, Jesika S.; Xue, Liang

    2010-01-01

    We report here a biophysical and biochemical approach to determine the differences in interactions of NiCR and NiCR-2H with DNA. Our goal is to determine whether such interactions are responsible for the recently observed differences in their cytotoxicity toward MCF-7 cancer cells. Viscosity measurement and fluorescence displacement titration indicated that both NiCR and NiCR-2H bind weakly to duplex DNA in the grooves. The coordination of NiCR-2H with the N-7 of 2′-deoxyguanosine 5′-monophosphate (5′-dGMP) is stronger than that of NiCR as determined by 1H NMR. NiCR-2H, like NiCR, can selectively oxidize guanines present in distinctive DNA structures (e.g., bulges), and notably, NiCR-2H oxidizes guanines more efficiently than NiCR. In addition, UV and 1H NMR studies revealed that NiCR is oxidized into NiCR-2H in the presence of KHSO5 at low molar ratios with respect to NiCR (≤4). PMID:20671951

  18. Point defect evolution in Ni, NiFe and NiCr alloys from atomistic simulations and irradiation experiments

    International Nuclear Information System (INIS)

    Using molecular dynamics simulations, we elucidate irradiation-induced point defect evolution in fcc pure Ni, Ni0.5Fe0.5, and Ni0.8Cr0.2 solid solution alloys. We find that irradiation-induced interstitials form dislocation loops that are of 1/3〈1 1 1〉{1 1 1}-type, consistent with our experimental results. While the loops are formed in all the three materials, the kinetics of formation is considerably slower in NiFe and NiCr than in pure Ni, indicating that defect migration barriers and extended defect formation energies could be higher in the alloys than pure Ni. As a result, while larger size clusters are formed in pure Ni, smaller and more clusters are observed in the alloys. Vacancy diffusion occurs at relatively higher temperatures than interstitials, and their clustering leads to the formation of stacking fault tetrahedra, consistent with our experiments. The results also show that the surviving Frenkel pairs are composition dependent and are largely Ni dominated

  19. Exclusive study of Ni+Ni and Ni+Au central collisions: phase coexistence and spinodal decomposition

    International Nuclear Information System (INIS)

    The INDRA multidetector allowed us to study the Ni+Ni collisions at 32A MeV and the Ni+Au collisions at 52,4 MeV. Central collisions leading to 'quasi-fused' systems were isolated using multidimensional analysis techniques: the Discriminant Analysis and the Principal Component Analysis. Comparison with a statistical model shows that the selected events are compatible with thermodynamical equilibrium. The average thermal excitation energy is 5A MeV for both systems. Calculations of heat capacities show that the deexcitation of the hot sources are akin to a liquid-gas phase transition of nuclear matter. Indeed heat capacities exhibit a negative branch as expected for a phase transition of a finite system. The dynamics of this phase transition has been investigated by applying the charge correlation method. An enhanced production of events with equal-sized fragments has been evidenced for Ni+Au at 52A MeV. No signal was found for Ni+Ni at 32A MeV. Finally this method was improved by taking into account the total charge conservation. The signal is seen more clearly for Ni+Au at 52A MeV, but is ambiguous for Ni+Ni at 32A MeV. The path followed in the state diagram, or the involved time scales, seem to be different for these systems. (authors)

  20. Site Preference and Alloying Effect of Excess Ni in Ni-Mn-Ga Shape Memory Alloys

    Institute of Scientific and Technical Information of China (English)

    CHEN Jie; LI Yan; SHANG Jia-Xiang; XU Hui-Bin

    2009-01-01

    @@ The formation energies and electronic structures of Ni-rich Ni-Mn-Ga alloys have been investigated by first-principles calculations using the pseudopotential plane wave method baaed on density functional theory. The results show that the alloying Ni prefers to occupy the Mn site directly in Ni9Mn3Ga4 and to occupy the Mn site and drive the displaced Mn atom to the Ga site in Ni9Mn4Ga3, which is in accordance with the experimental result. According to the lattice constants and the density of states analyses, these site preference behaviours are closely related to the smaller lattice distortion and the lower-energy electronic structure when the excess Ni occupies the Mn site. The effect of Ni alloying on martensitic transformation is discussed and the enhancement of martensitic transformation temperature by Ni alloying is estimated by the calculated formation energy difference between anstenite and martensite phases.

  1. The ternary system Tm-Ni-In at 870 K

    International Nuclear Information System (INIS)

    The isothermal section of the Tm-Ni-In system at T = 870 K was constructed. Nine ternary compounds: Tm10Ni9In20, TmNi1-0.60In1-1.40, Tm2Ni2In, Tm2Ni1.78In, Tm5Ni2In4, Tm11Ni4In9, Tm4.83Ni2In1.17, Tm6Ni2In and Tm14Ni3In3 exist in the system at the temperature of investigation. Solid solutions with In/Ni and Tm/In mixing were noticed for numerous compounds. A broad substitution of Ni for In was observed for TmNi1-0.60In1-1.40, and of Tm for In for the TmNi2-TmNi4In section. An interstitial solid solution TmxNiIn, based on binary equiatomic NiIn, extends up to 8 at.% Tm (x = 0.17). The magnetic properties of TmNiIn, Tm2Ni2In and Tm5Ni2In4 are also reviewed.

  2. ELEKTRIČNI OBLOK V VAROVALKAH

    OpenAIRE

    Zakelšek, Rok

    2012-01-01

    V diplomski nalogi je obravnavan električni oblok v taljivih varovalkah. Predstavljene so nizkonapetostne in visokonapetostne varovalke ter zgodovinski razvoj električnih varovalk. Opisan je električni oblok in vpliv na električni oblok v nizkonapetostnih taljivih varovalkah ter izvedba preskusov. Izvedeni so bili preskusi na taljivih vložkih z različno granulacijo in količino peska, spremembo talilnega elementa ter spremembo volumna taljivega vložka.

  3. Composite Ni/NiO-Cr2O3 Catalyst for Alkaline Hydrogen Evolution Reaction

    Energy Technology Data Exchange (ETDEWEB)

    Bates, MK; Jia, QY; Ramaswamy, N; Allen, RJ; Mukerjee, S

    2015-03-12

    We report a Ni-Cr/C electrocatalyst with unpreeedented massactivity for the hydrogen evolution reaction (HER). in alkaline electrolyte. The HER Oietics of numerous binary and ternary Ni-alloys and composite Ni/metal-euride/C samples were evaluated in aquebus 0.1 M KOH electrolyte. The highest HER mass-activity was observed for Ni-Cr materials which exhibit metallic Ni as well as NiOx and Cr2O3 phases as determined by X-ray diffraction (XRD) and X-ray absorption spectroscopy (XAS) analysis. The onset of the HER is significantly improved compared to munerous binary dor ternary Ni-alloys, inCluding Ni Mg materials. It is likely that at adjacent Ni/NiOx sites, the oxide acts as a sink for OHads, while the metallic Ni acts as a, sink for the H-ads, intermediate of the HER, thus minimizing the high activation energy of hydrogen evolution via water reduction. This is confirmed by in situ XAS studies that show that the synergistic HER enhancement is due to NiO content and that the Cr2O3 appears to stabilize the composite NiO component-under HER conditions (where NiOx would typically be reduced to metallic Ni-0). Furthermore, in contrast to Pt, the Ni(O-x)/Cr2O3 catalyst appears resistant to poisoning by the anion.exchange ionomer (AEI), a serloua consideration when applied to an anionic polymer electrolyte interface. Furthermore, we report a: detailed model of the double layer interface which helps explain the observed ensemble effect in the presence of AEI.

  4. Digitalno samozaložništvo

    OpenAIRE

    KRANJC, ALJAŽ

    2016-01-01

    Digitalno založništvo (znano tudi kot e-založništvo ali elektronsko založništvo) zajema digitalno publikacijo e-knjig, digitalnih revij in razvoj digitalnih knjiž-nic in katalogov. Postalo je nekaj običajnega, da se knjige, revije in časopise distribuira v digitalni obliki. Za izdelavo in oblikovanje naših besedil imamo na voljo veliko spletnih orodij, ki se razlikujejo po namenu glede na vrsto besedila (navadna besedila, znanstveni članki, spletne vsebine). Pregledali smo več samozaložniških...

  5. Effects of Ni vacancy, Ni antisite, Cr and Pt on the third-order elastic constants and mechanical properties of NiAl

    KAUST Repository

    Wu, Shaohua

    2014-12-01

    Effects of Ni vacancy, Ni antisite in Al sublattice, Cr in Al sublattice, Pt in Ni sublattice on the second-order elastic constants (SOECs) and third-order elastic constants (TOECs) of the B2 NiAl have been investigated using the first-principles methods. Lattice constant and the SOECs of NiAl are in good agreement with the previous results. The brittle/ductile transition map based on Pugh ratio G/B and Cauchy pressure Pc shows that Ni antisite, Cr, Pt and pressure can improve the ductility of NiAl, respectively. Ni vacancy and lower pressure can enhance the Vickers hardness Hv of NiAl. The density of states (DOS) and the charge density difference are also used to analysis the effects of vacancy, Ni antisite, Cr and Pt on the mechanical properties of NiAl, and the results are in consistent with the transition map. © 2014 Elsevier Ltd. All rights reserved.

  6. Joining of Ni-TiC FGM and Ni-Al Intermetallics by Centrifugal Combustion Synthesis

    International Nuclear Information System (INIS)

    A centrifugal combustion synthesis (CCS) process has been investigated to join a Ni-Al intermetallic compound and a Ni-TiC cermet. The cermet, a tubular graphite mold, and a green compact of reactants consisting of Al, Ni and NiO were set in a centrifugal caster. When the combustion synthesis reaction was induced in the centrifugal force field, a synthesized molten Ni-Al alloy flowed into the graphite mold and joined to the cermet. The soundness of the joint interface depended on the volume percentage of TiC phase in the cermet. A lot of defects were formed near the interface between the Ni-TiC cermet and the cast Ni-Al alloy when the volume percentage of TiC was 50% or higher. For this kind of cermet system, using a functionally graded cermet such as Ni-10 vol.%TiC/Ni-25 vol.%TiC/Ni-50 vol.%TiC overcame this difficulty. The four-point bending strength of the joined specimen consisting of the three-layered FGM cermet and cast Ni-29 mol%Al alloy was 1010 MPa which is close to the result for a Ni-29 mol%Al alloy specimen

  7. REE in cretaceous to tertiary granitoids of Chugoku and Shikoku district, SW Japan

    Energy Technology Data Exchange (ETDEWEB)

    Imaoka, Teruyoshi [Yamaguchi Univ. (Japan). Faculty of Science; Harada, Michiru

    1998-01-01

    `Niho plutonic composite rocks` distributed in Niho Kamigo area in the northeast of Yamaguchi-city in Japan. It is small plutonic composite rocks, of about 2 km in long length and 1 km of short length. The rocks were studied by the geological survey. Many kinds of rock and rare earth elements were determined. The constitution process is estimated by these results. It consists of gabbro-quartz diorite-tonalite{center_dot}granodiorite-granito. The more inside of rock existed, the more felsic rock are discovered. Chemical compositions were TiO{sub 2}, FeO, MnO and K{sub 2}O. It is estimated that intrusion of tonalite and successive intrusion of granodiorite generated and then formed in situ crystallization differentiation. (S.Y.)

  8. Evaluation of transient test results of Shimane Nuclear Power Station, Chugoku Electric Power Co., Inc

    International Nuclear Information System (INIS)

    The start-up test of the plant No.1 of Shimane Nuclear Power Station, has been successfully completed for a rather short period. This report describes on the abnormal transient changes that may be considered to occur in BWR plants. The report also states appropriateness of the evaluation of transient change by plant dynamics-analyzing code. The possible causes of abnormal transient change include the systems of main steam, feed water, recirculation and control rod actuation. Start-up test items were selected by preliminary evaluation. The following close investigations were carried out prior to the start-up test; examination of the preceding plants, investigation by plant dynamics analysis, various preliminary tests before the start-up test and organization setup for the start-up test. The evaluation items in rated output test were: total closing of main steam isolation valve, turbine trip (sudden closing of main steam stop valve), load shut-off (sudden closing of regulating valve) feed pump trip, and recirculation motor-generator set trip. The plant has been confirmed to be fully safe and to have the expected performance through individual abnormal transient tests. The improvements of the analysis code will be subsequently continued and reflected to the plant design. (Wakatsuki, Y.)

  9. Spin polarization effect of Ni2 molecule

    Institute of Scientific and Technical Information of China (English)

    Yan Shi-Ying; Zhu Zheng-He

    2008-01-01

    The density functional theory (DFT) method (b3p86) of Gaussian 03 is used to optimize the structure of the Ni2 molecule. The result shows that the ground state for the Ni2 molecule is a 5-multiple state, symbolizing a spin polarization effect existing in the Ni2 molecule, a transition metal molecule, but no spin pollution is found because the wavefunction of the ground state does not mingle with wavefunctions of higher-energy states. So the ground state for Ni2 molecule, which is a 5-multiple state, is indicative of spin polarization effect of the Ni2 molecule, that is, there exist 4 parallel spin electrons in Ni2 molecule. The number of non-conjugated electrons is greatest. These electrons occupy different spatial orbitals so that the energy of the Ni2 molecule is minimized. It can be concluded that the effect of parallel spin in the Ni2 molecule is larger than that of the conjugated molecule, which is obviously related to the effect of electron d delocalization. In addition, the Murrell-Sorbie potential functions with the parameters of the ground state and other states of the Ni2 molecule are derived. The dissociation energy De for the ground state of the Ni2 molecule is 1.835 eV, equilibrium bond length Re is 0.2243 nm, vibration frequency ωe is 262.35 cm-1. Its force constants f2, f3 and f4 are 1.1901 aJ.nm-2, 5.8723 aJ.nm-3, and 21.2505 aJ.nm-4 respectively. The other spectroscopic data for the ground state of the Ni2 molecule ωexe, Be and αe are 1.6315cm-1, 0.1141 cm-1, and 8.0145×10-4 cm-1 respectively.

  10. EELS study of the epitaxial graphene/Ni(111) and graphene/Au/Ni(111) systems

    OpenAIRE

    Generalov, A.; Dedkov, Y.

    2011-01-01

    We have performed electron energy-loss spectroscopy (EELS) studies of Ni(111), graphene/Ni(111), and the graphene/Au/Ni(111) intercalation-like system at different primary electron energies. A reduced parabolic dispersion of the \\pi plasmon excitation for the graphene/Ni(111) system is observed compared to that for bulk pristine and intercalated graphite and to linear for free graphene, reflecting the strong changes in the electronic structure of graphene on Ni(111) relative to free-standing ...

  11. Preparation and characterization of Cu(111)-Ni and Cu(110)-Ni surface alloys

    OpenAIRE

    Geus, John W.; Mesters, C.M.A.M.; Wermer, G.; Gijzeman, O.L.J.

    1984-01-01

    The interaction of Ni(CO)4/CO gas mixtures with Cu(111) and Cu(110) single crystal surfaces has been studied with ellipsometry. Auger electron spectroscopy, LEED and argon ion depth profiling. At room temperature Ni atoms with some CO ligands remain at the surface. The amount of Ni that can be deposited is less than one monolayer. The alloy surface is able to bind CO. After exposures above 220°C, the initially deposited amount of Ni resides below the first layer of Cu atoms. The amount of Ni ...

  12. Cosmic ray half life of 56Ni

    International Nuclear Information System (INIS)

    A search for the β+ decay of 56Ni has established an upper limit on the branching ratio of 7.2 x 10-7 for the most likely such transition. This provides a lower limit of 2.3 x 104 years for the cosmic ray half life of 56Ni. 2 refs., 2 figs

  13. Purification of a Ni sup 2+ -binding protein, pNiXa, from Xenopus ovary

    Energy Technology Data Exchange (ETDEWEB)

    Beck, B.L.; Makowski, G.S.; Nomoto, S.; Sunderman, F.W. (Univ. of Connecticut, Farmington (United States))

    1991-03-11

    Previous research on nickel-induced teratogenesis in Xenopus laevis identified several Ni{sup 2+}-binding proteins, including pNiXa in Xenopus ovaries, unfertilized eggs, and embryos. A major goal of this research project is elucidating the role of pNiXa in the uptake, embryotoxicity, and teratogenicity of Ni{sup 2+} in Xenopus. To purify and identify pNiXa, ovarian tissue from mature Xenopus females was homogenized in 3 vol of Tris buffer and centrifuged. The supernatant was centrifuged; the ultracentrifugal supernatant was batch-adsorbed onto DEAE-cellulose. The pNiSa remained unbound and was subsequently adsorbed on phosphocellulose and eluted by a step-wise NaCl gradient. The pNiXa was eluted in 0.25 M NaCl; this fraction was concentrated, and further purified by reverse phase chromatography on a 5 {mu}m C-8 column, with a linear trifluoroacetic acid/acetonitrile gradient. The pNiXa was eluted at {approximately}56% acetonitrile, yielding a single protein band with mol wt {approximately}47 kD,based on SDS-PAGE analysis. Comparison of the amino acid composition of pNiXa versus the results obtained by automated Edman degradation indicated that the N-terminus of pNiXa was blocked. Sequencing of peptide fragments of pNiXa is underway.

  14. Thermodynamic Analysis of Electrodeposited Ni-Mo and Ni-Mo-P Alloys

    Institute of Scientific and Technical Information of China (English)

    GUO Zhong-cheng; XU Rui-dong; WANG Ji-kun

    2004-01-01

    The potential-pH diagram of Ni-P-H2O system is calculated and constructed by use of thermodynamic data. On the basis of the potential-pH diagram the electrochemical behaviors of electrodepositing Ni-Mo and Ni-Mo-P alloys are analyzed. The phases of Ni-Mo and Ni-Mo-P coatings are identified by means of X-ray diffraction analysis. The thermodynamic analysis shows that it is difficult to deposit Mo or P individually from its aqueous solution, and they must be co-deposited with other metals by induced deposition; P and Ni can be deposited as compound Ni3P on the cathode; Mo is deposited in two forms: one is in the form of MoO3 solid particles and the other is in the form of compound MoC. X-ray diffraction analysis is in agreement with the thermodynamic analysis.

  15. Nanoscale structural heterogeneity in Ni-rich half-Heusler TiNiSn

    Energy Technology Data Exchange (ETDEWEB)

    Douglas, Jason E., E-mail: jedouglas@mrl.ucsb.edu; Pollock, Tresa M. [Materials Department, University of California, Santa Barbara, California 93106 (United States); Materials Research Laboratory, University of California, Santa Barbara, California 93106 (United States); Chater, Philip A. [Diamond Light Source, Chilton, Oxfordshire OX11 0DE (United Kingdom); Brown, Craig M. [Center for Neutron Research, National Institute of Standards and Technology, Gaithersburg, Maryland 20899 (United States); Department of Chemical Engineering, University of Delaware, Newark, Delaware 19716 (United States); Seshadri, Ram [Materials Department, University of California, Santa Barbara, California 93106 (United States); Materials Research Laboratory, University of California, Santa Barbara, California 93106 (United States); Department of Chemistry and Biochemistry, University of California, Santa Barbara, California 93106 (United States)

    2014-10-28

    The structural implications of excess Ni in the TiNiSn half-Heusler compound are examined through a combination of synchrotron x-ray and neutron scattering studies, in conjunction with first principles density functional theory calculations on supercells. Despite the phase diagram suggesting that TiNiSn is a line compound with no solid solution, for small x in TiNi{sub 1+x}Sn there is indeed an appearance—from careful analysis of the scattering—of some solubility, with the excess Ni occupying the interstitial tetrahedral site in the half-Heusler structure. The analysis performed here would point to the excess Ni not being statistically distributed, but rather occurring as coherent nanoclusters. First principles calculations of energetics, carried out using supercells, support a scenario of Ni interstitials clustering, rather than a statistical distribution.

  16. Nanoscale structural heterogeneity in Ni-rich half-Heusler TiNiSn

    International Nuclear Information System (INIS)

    The structural implications of excess Ni in the TiNiSn half-Heusler compound are examined through a combination of synchrotron x-ray and neutron scattering studies, in conjunction with first principles density functional theory calculations on supercells. Despite the phase diagram suggesting that TiNiSn is a line compound with no solid solution, for small x in TiNi1+xSn there is indeed an appearance—from careful analysis of the scattering—of some solubility, with the excess Ni occupying the interstitial tetrahedral site in the half-Heusler structure. The analysis performed here would point to the excess Ni not being statistically distributed, but rather occurring as coherent nanoclusters. First principles calculations of energetics, carried out using supercells, support a scenario of Ni interstitials clustering, rather than a statistical distribution.

  17. Pt redistribution during Ni(Pt) silicide formation

    OpenAIRE

    Demeulemeester, Jelle; Smeets, D.; Van Bockstael, C; Detavernier, C.; Comrie, C. M.; Barradas, N. P.; Vieira, A; Vantomme, André

    2008-01-01

    We report on a real-time Rutherford backscattering spectrometry study of the erratic redistribution of Pt during Ni silicide formation in a solid phase reaction. The inhomogeneous Pt redistribution in Ni(Pt)Si films is a consequence of the low solubility of Pt in Ni2Si compared to NiSi and the limited mobility of Pt in NiSi. Pt further acts as a diffusion barrier and resides in the Ni2Si grain boundaries, significantly slowing down the Ni2Si and NiSi growth kinetics. Moreover, the observed in...

  18. PtSnNi/C nanoparticle electrocatalysts for the ethanol oxidation reaction: Ni stability study

    International Nuclear Information System (INIS)

    Highlights: ► The addition of Sn and Ni to Pt significantly improves the electrocatalytic activities for EOR. ► PtSnNi/C retain the structure of Pt at values similar to that of pure Pt. ► PtSnNi/C exhibited a lower dissolution of Ni than the binary alloy after accelerated stress tests. ► A change in the product formation pathways before and after accelerated stress tests was observed. -- Abstract: This work describes the use of Pt3Sn/C, Pt3Ni/C and Pt3SnNi/C nanoparticle electrocatalysts with a 20% metal loading on carbon prepared using the polymeric precursor method for the ethanol oxidation reaction (EOR). XRD measurements revealed the presence of segregated Pt and NiO phases in the Pt3Ni/C electrocatalysts, whereas for Pt3SnNi/C, there was some evidence that Ni and Sn atoms are incorporated into the Pt structure with the presence of segregated SnO2 and NiO phases. The mean crystallite sizes were 3.6, 5.7 and 7.2 nm for Pt3Sn/C, Pt3Ni/C, and Pt3SnNi/C, respectively. The onset oxidation potential obtained for the EOR using Pt3SnNi/C was close to 0.22 V. Chronoamperometric measurements revealed that the highest current densities for the EOR were obtained using the Pt3SnNi/C nanoparticle electrocatalysts (16 mA mgPt−1). Based on the Ni accelerated stress tests, this element was more stable in the ternary material. In contrast, there was a change in the product formation pathways before (acetaldehyde and acetic acid were the primary products) and after the accelerated stress tests (acetaldehyde was the primary product) for the Pt3SnNi/C catalyst. The experimental results indicate that the Pt3SnNi/C electrocatalysts exhibited better electrocatalytic activity compared to the other electrocatalysts for the EOR. It is suggested that this activity is related to the presence of Ni, which can modify the electronic structure of Pt and combine with Sn to facilitate the removal of adsorbed CO on the surface of the Pt, thereby promoting the EOR

  19. Microscopic phase field study of the antisite defect of Ni3 Al in binary Ni-Al alloys

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    The temporal evolution feature of a microscopic phase field model is utilized to study the antisite defects of L1 2-Ni 3 Al;this is quite different from other physicist’ interests.There are mainly two points in brief.Firstly,antisite defects Ni Al and Al Ni ,which are caused by the deviation from the stoichiometric Ni 3 Al,coexist in the Ni 3 Al phase.The surplus Ni atom in the Ni-rich side is prone to substitute Al thus producing the antisite defect Ni Al that maintains the stability of the L1 2 structure.In other case,the surplus Al atom in the Al-rich side is accommodated by a Ni sublattice consequently giving rise to antisite defect Al Ni .The calculated equilibrium occupancy probability of Ni Al is much higher than that of Al Ni .This point is generally in line with other theoretical and experimental works.Additionally,both Ni Al and Al Ni have a strong negative correlation to time step during the disorder-order transformation.Since the initial value of Ni Al and Al Ni on each site of the matrix is right at the concentration that we set,we can observe the decrease process of Ni Al and Al Ni from the initial disordered high anti-structure state to their respective equilibrium state,i.e.to the result of the ordering process further coarsening.

  20. On the constitution and thermodynamics of Ni-Gd alloys

    International Nuclear Information System (INIS)

    The thermodynamic properties of Ni-Gd alloys were determined by electromotive force measurements between 873 and 1073 K on galvanic cells using CaF2 single crystals as solid electrolytes. Results yield a complete set of thermodynamic functions for the intermetallic phases (Ni), Ni17Gd2, Ni5Gd, Ni4Gd, Ni7Gd2, Ni3Gd, Ni2Gd, NiGd, Ni2Gd3, and NiGd3, as well as information on the phase relations. The system is characterized by pronounced negative deviations from ideality. The relative partial excess Gibbs energy of gadolinium at infinite dilution was determined to be -(104±5) kJ/mol. A comparison with analogous systems indicates the influence of the electronic structure of the components on thermodynamic properties of mixing. In order to fix the liquidus curve, differential thermal analysis was carried out over the entire range of composition. (orig.)

  1. Microstructure of Ni-Al powder and Ni-Al composite coatings prepared by twin-wire arc spraying

    Science.gov (United States)

    Wang, Ji-xiao; Wang, Gui-xian; Liu, Jing-shun; Zhang, Lun-yong; Wang, Wei; Li, Ze; Wang, Qi-xiang; Sun, Jian-fei

    2016-07-01

    Ni-Al powder and Ni-Al composite coatings were fabricated by twin-wire arc spraying (TWAS). The microstructures of Ni-5wt%Al powder and Ni-20wt%Al powder were characterized by scanning electronic microscopy (SEM) and energy dispersive spectroscopy (EDS). The results showed that the obtained particle size ranged from 5 to 50 μm. The morphology of the Ni-Al powder showed that molten particles were composed of Ni solid solution, NiAl, Ni3Al, Al2O3, and NiO. The Ni-Al phase and a small amount of Al2O3 particles changed the composition of the coating. The microstructures of the twin-wire-arc-sprayed Ni-Al composite coatings were characterized by SEM, EDS, X-ray diffraction (XRD), and transmission electron microscopy (TEM). The results showed that the main phase of the Ni-5wt%Al coating consisted of Ni solid solution and NiAl in addition to a small amount of Al2O3. The main phase of the Ni-20wt%Al coating mainly consisted of Ni solid solution, NiAl, and Ni3Al in addition to a small amount of Al and Al2O3, and NiAl and Ni3Al intermetallic compounds effectively further improved the final wear property of the coatings. TEM analysis indicated that fine spherical NiAl3 precipitates and a Ni-Al-O amorphous phase formed in the matrix of the Ni solid solution in the original state.

  2. X-ray photoelectron spectroscopy and magnetism of AlDyNi, AlDyNi4 and AlDy3Ni8 compounds

    International Nuclear Information System (INIS)

    The electronic and magnetic properties of AlDyNi, AlDyNi4 and AlDy3Ni8 are studied using X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), static and dynamic magnetic measurements. The three compounds AlDyNi, AlDyNi4 and AlDy3Ni8 are single phases and crystallize in the Fe2P, CaCu5 and CeNi3 structure types, respectively. All the investigated compounds order ferromagnetically below the corresponding Curie temperatures. The Curie temperature and the magnetic moments are 25 K and 6 μB/f.u. for AlDyNi, 14 K and 6.9 μB/f.u. for AlDyNi4 and 22K and 19.2 μB/f.u. for AlDy3Ni8. At high temperature the magnetic susceptibility obey the Curie-Weiss law. The paramagnetic Curie temperature and the effective magnetic moments are 30K and 10.88 μB/f.u. for AlDyNi, 28 K and 10.94 μB/f.u. for AlDyNi4 and 18 K and 18.33 μB/f.u. for AlDy3Ni8. XPS valence band and Ni 2p spectra indicated the presence of small magnetic moment on Ni sites in AlDy3Ni8 and AlDyNi4, and a complete filling of Ni 3d band in AlDyNi.

  3. Study of the central collisions in the reactions Ni + Al and Ni + Ni at 28 A.MeV; Etude des collisions centrales dans les reactions Ni + Al et Ni + Ni a 28 A.MeV

    Energy Technology Data Exchange (ETDEWEB)

    Lebreton, L.

    1995-12-01

    The work is in characterisation of mechanisms in the energy range of onset of multifragmentation (excitation energy of composed nucleus around 4 - 5 AMeV). This work focused on an experiment performed at the SARA facility, in Grenoble, using the AMPHORA multi detection array. I have been particularly interested in central collisions in the Ni + Al and Ni + Ni systems. The possibility to detect complete events for Ni + Al, and quasi-complete events for the Ni + Ni case, is the reason of this choice. Furthermore Ni + Ni presents the interest of a symmetrical system, for which the excitation energy per nucleon is maximum. The study of these reactions has been focused on the quasi-complete events (events for which at least 80 % of the total charge has been detected). Heavy ions produced in peripheral collisions are very likely emitted along the beam line or stopped in the plastic detectors, energy thresholds are too high for the quasi-target products detection, consequently by requiring complete or quasi-complete measurement of the total charge, we are able to detect mostly central events. The knowledge of informations like charge, energy or detection angles allows to isolate the source(s) and to reconstruct the size and the excitation energy of the source(s). Comparisons with simulations like sequential emission (GEMINI code), very deep inelastic collision or instantaneous emission (Berliner code) allows to characterise the first stage of the collision (binary collisions or central collisions) and the type of deexcitation of the source(s). Some calculations was also performed with the statistical model code MODGAN. Indeed azimuthal correlations seem to be a good tool in getting more information about involved reaction mechanisms. Comparisons with MODGAN provide information about angular momentum of the source and time delay between emissions of the two particles (separation between sequential or instantaneous process). (author). 69 refs.

  4. Synthesis of honeycomb-like NiS2/NiO nano-multiple materials for high performance supercapacitors

    International Nuclear Information System (INIS)

    Highlights: •3D honeycomb-like NiS2/NiO were prepared via a green hydrothermal process. •The NiS2 reduces the electrochemical impedance of NiO. •The NiS2/NiO electrode exhibits exceptional electrochemical performance. -- Abstract: Three dimensional (3D) honeycomb-like NiS2/NiO nano-multiple materials were successfully prepared by fabricating cribrate NiS2 on the surface of NiO nanosheets through simple hydrothermal process on nickel foam. The morphology and phase structure of the NiS2/NiO are characterized by scanning electron microscopy equipped with energy dispersive X-ray spectrometer, transmission electron microscope, X-ray diffractometer and the electrochemical properties are tested by cyclic voltammetry, galvanostatic charge/discharge and electrochemical impedance spectroscopy. The NiS2/NiO electrode owns lower electrochemical impedance compared with bare NiO substrate and exhibits exceptional capacitance performance with a high specific capacitance of 2251 F g−1 delivered at current density of 1 A g−1, while 1192 F g−1 retained at 20 A g−1. What's more, after 2000 cycles, the specific capacitance remains 1275 F g−1 (at 5 A g−1) with a capacitance retention of 78%. Therefore, the NiS2/NiO electrode shows remarkable electrochemical performance and has a promising future for electrochemical supercapacitors

  5. Synthesis of Supported NiPt Bimetallic Nanoparticles, Methods for Controlling the Surface Coverage of Ni Nanoparticles With Pt, Methods Of Making NiPt Multilayer Core-Shell Structures and Application of the Supported Catalysts for CO2 Reforming

    KAUST Repository

    Li, Lidong

    2015-06-25

    Embodiments of the present disclosure provide for supported Ni/Pt bimetallic nanoparticles, compositions including supported NiPt nanoparticles, methods of making supported NiPt nanoparticles, methods of using supported NiPt nanoparticles, and the like.

  6. Magnetic properties of Ni2N

    International Nuclear Information System (INIS)

    A powder sample of body-centered tetragonal Ni2N in a single phase was prepared by a high rate-type triode dc reactive sputtering and the magnetic properties have been reinvestigated. It is confirmed that Ni2N is not a ferromagnet. However, the material is not a simple paramagnet either and shows a weak spin-glass-like behavior at low temperatures with a freezing temperature of about 8 K. Posible origins of the behavior are discussed. Band-structure calculations are reported to see the stability of the nonmagnetic ground state of bct Ni2N against lattice expansion and appearance of nitrogen vacancies

  7. Manejo del niño febril

    OpenAIRE

    Sara Fernández-Rojas; Rolando Ulloa-Gutiérrez; María L. Avila-Aguero

    2004-01-01

    Introducción: La fiebre en el niño es uno de los principales motivos de consulta en pediatría. En ocasiones, el temor de los padres produce la conocida "fobia febril", que conlleva al uso de los servicios de emergencias hospitalarios y a tratamientos inadecuados. Objetivo: Conocer la percepción, el conocimiento y el manejo que dan a la fiebre los padres o encargados de familia, de aquellos niños hospitalizados en el servicio de Infectología del Hospital Nacional de Niños "Dr. Carlos Sáenz Her...

  8. New developments in Ni/Ti multilayers

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, I.; Hoghoj, P. [Institut Max von Laue - Paul Langevin (ILL), 38 - Grenoble (France)

    1997-04-01

    It is now 20 years since super-mirrors were first used as a neutron optical element. Since then the field of multilayer neutron-optics has matured with multilayers finding their way to application in many neutron scattering instruments. However, there is still room for progress in terms of multilayer quality, performance and application. Along with work on multilayers for neutron polarisation Ni/Ti super-mirrors have been optimised. The state-of-the-art Ni/Ti super-mirror performance and the results obtained in two neutron-optics applications of Ni/Ti multilayers are presented. (author).

  9. Effect of metallic phase content on mechanical properties of (85Cu- 15Ni)/(10NiO-NiFe2O4) cermet inert anode for aluminum electrolysis

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    (85Cu-15Ni)/(10NiO-NiFe2O4) cermets were prepared with Cu-Ni mixed powders as toughening metallic phase and 10NiO-NiFe2O4 as ceramic matrix. The phase composition, microstructure of composite and the effect of metallic phase content on bending strength, hardness, fracture toughness and thermal shock resistance were studied. X-ray diffraction analysis indicates the coexistence of (Cu-Ni), NiO and NiFe2O4 phases in the cermets. Within the content range of metallic phase from 0% to 20% (mass fraction), the maximal bending strength (176.4 MPa) and the minimal porosity (3.9%) of composite appear at the metallic phase content of 5%. The fracture toughness increases and Vickers' hardness decreases with increasing metal content. When the thermal shock temperature difference (△t) is below 200 ℃, the loss rate of residual strength for 10NiO-NiFe2O4 ceramic is only 8%, but about 40% for (85Cu-15Ni)/(10NiO-NiFe2O4) cermets. As △t is above 200 ℃, the residual strength sharply decreases for sample CN0 and falls slowly for samples CN5-CN20.

  10. Transport properties of Nb/PdNi bilayers and Nb/PdNi/Nb Josephson junctions

    International Nuclear Information System (INIS)

    The superconducting proximity effect was examined in both Nb/PdNi (SF) bilayer films and Nb/PdNi/Nb (SFS) Josephson junctions. In Nb/PdNi bilayer films, nonmonotonic behavior of Tc was observed as a function of PdNi thickness dF. The effective exchange energy Eex extracted from the data was about 13 meV. In Nb/PdNi/Nb (SFS) Josephson junctions, the existence of a crossover between the 0 state and the π state was confirmed in the PdNi thickness dependence of Ic. For the junction with dF = 9 nm, such a crossover was observed in the temperature dependence of Ic. Eex estimated from the junctions characteristics was about 19 meV. These behaviors can be interpreted from the view point of a damped oscillatory superconducting order parameter induced at the SF interface.

  11. Microstructure and Martensitic Transformation Behaviors of Explosively Welded NiTi/NiTi Laminates

    Institute of Scientific and Technical Information of China (English)

    YAN Zhu; CUI Li-shan; ZHENG Yan-jun

    2007-01-01

    The study is a first attempt to prepare bulk NiTi/NiTi shape memory alloy (SMA) laminates with a macroscopic heterogeneous composition by explosive welding and investigate their microstructures and martensitic transformation behaviors. After explosive welding, a perfect interfacial bonding between the two components and a reversible martensitic transformation are realized in the tandem.Results show achievement of a fine granular structure and the maximum value of microhardness near the welding interface because of the excessive cold plastic deformation and the high impact velocity during the explosive welding. Meanwhile, the effects of aging on the transformation of the welded tandem are investigated by differential scanning calorimeter (DSC) and subject to discussion. The transformation temperatures of NiTi/NiTi SMAs increase with the rise of the aging temperature. The experimental results indicate the shape memory properties of NiTi/NiTi SMA fabricated by explosive welding can be improved by optimizing the aging technology.

  12. Enhanced broadband near-infrared luminescence from Ni in Bi/Ni-doped transparent glass ceramics

    International Nuclear Information System (INIS)

    Spectral properties of Bi/Ni-doped transparent MgO-Al2O3-Ga2O3-SiO2-TiO2 glass ceramics (GCs) containing spinel solution nanocrystals were investigated. The emission intensity of Ni in Bi/Ni-doped GCs was about 4 times stronger than that of Ni-doped GCs due to energy transfer from Bi to Ni. The Bi/Ni-doped GCs with 0.75 mol% Bi2O3 concentration exhibited a near-infrared emission with full width at half maximum of about 270 nm and a fluorescent lifetime of about 350 μs, making them very promising for applications in broadband optical amplifiers and tunable lasers.

  13. Enhanced broadband near-infrared luminescence from Ni in Bi/Ni-doped transparent glass ceramics

    Science.gov (United States)

    Wu, Botao; Ruan, Jian; Qiu, Jianrong; Zeng, Heping

    2009-07-01

    Spectral properties of Bi/Ni-doped transparent MgO-Al2O3-Ga2O3-SiO2-TiO2 glass ceramics (GCs) containing spinel solution nanocrystals were investigated. The emission intensity of Ni in Bi/Ni-doped GCs was about 4 times stronger than that of Ni-doped GCs due to energy transfer from Bi to Ni. The Bi/Ni-doped GCs with 0.75 mol% Bi2O3 concentration exhibited a near-infrared emission with full width at half maximum of about 270 nm and a fluorescent lifetime of about 350 µs, making them very promising for applications in broadband optical amplifiers and tunable lasers.

  14. Enhanced broadband near-infrared luminescence from Ni in Bi/Ni-doped transparent glass ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Wu Botao; Zeng Heping [State Key Laboratory of Precision Spectroscopy and Department of Physics, East China Normal University, Shanghai 200062 (China); Ruan Jian [Shanghai Institute of Optics and Fine Mechanics, Chinese Academy of Sciences, Shanghai 201800 (China) and Graduate School of the Chinese Academy of Sciences, Beijing 100039 (China); Qiu Jianrong, E-mail: botao.wu@yahoo.com.c [State Key Laboratory of Silicon Materials, Zhejiang University, Hangzhou 310027 (China)

    2009-07-07

    Spectral properties of Bi/Ni-doped transparent MgO-Al{sub 2}O{sub 3}-Ga{sub 2}O{sub 3}-SiO{sub 2}-TiO{sub 2} glass ceramics (GCs) containing spinel solution nanocrystals were investigated. The emission intensity of Ni in Bi/Ni-doped GCs was about 4 times stronger than that of Ni-doped GCs due to energy transfer from Bi to Ni. The Bi/Ni-doped GCs with 0.75 mol% Bi{sub 2}O{sub 3} concentration exhibited a near-infrared emission with full width at half maximum of about 270 nm and a fluorescent lifetime of about 350 mus, making them very promising for applications in broadband optical amplifiers and tunable lasers.

  15. Phase stability and magnetism in NiPt and NiPd alloys

    Energy Technology Data Exchange (ETDEWEB)

    Paudyal, Durga; Mookerjee, Abhijit [S N Bose National Centre for Basic Sciences, JD Block, Sector 3, Salt Lake City, Kolkata 700098 (India)

    2004-08-18

    We show that the differences in stability of 3d-5d NiPt and 3d-4d NiPd alloys arise mainly due to relativistic corrections. The magnetic properties of disordered NiPd and NiPt alloys also differ due to these corrections, which lead to increase in the separation between the s-d bands of 5d elements in these alloys. For the magnetic case we also analyse the results in terms of splitting of majority and minority spin d band centres of the 3d elements. We further examine the effect of relativistic corrections to the pair energies and order-disorder transition temperatures in these alloys. The magnetic moments and Curie temperatures have also been studied along with the short range ordering/segregation effects in NiPt/NiPd alloys.

  16. NiCo-lead zirconium titanate-NiCo trilayered magnetoelectric composites prepared by electroless deposition

    International Nuclear Information System (INIS)

    The NiCo layers with various Ni/Co atomic ratio have been successfully electroless deposited on PZT layers by varying the bath composition. As the cobalt atomic ratio in the deposited layer increases from 17.2 to 54.8 wt%, the magnetostrictive coefficient decreases. The magnetoelectric effect depends strongly on the magnetostrictive properties of magnetostrictive phase. The magnetoelectric coefficient of NiCo/PZT/NiCo trilayers increases with Ni/Co atomic ratio of the deposited NiCo layers increasing from 45:55 to 83:17. A maximum ME voltage coefficient of αE,31 = 2.8 V ⋅ cm−1 ⋅ Oe−1 is obtained at a frequency of about 88 kHz, which makes these trilayers suitable for applications in actuators, transducers and sensors

  17. Effect Of Ni-Additions In NANOCRYSTALLIZED FeNiNbCuSiB Alloys

    International Nuclear Information System (INIS)

    Structure and magnetic properties of Fe73.5-xNixNb3Cu1 Si13.5B9 ( x = 0, 5, 10, 15, 20, 25 at.% ) amorphous and nanocrystalline alloys were investigated. For studying the magnetic behaviour upon changes of Ni and Fe concentration X-ray, Moessbauer measurements as well as thermomagnetic analyses were performed. The first crystallization temperature at about 545 deg C was nearly independent on the Ni concentrations. The temperature of the second crystallization stage decreases when Ni content increases. Additions of Ni cause a small change of the Curie temperature. After annealing at 550 deg C for 1 h a nanocrystalline state was formed which leads to magnetic softening of the sample for smaller additions of Ni (x = 0 - 15). The nanocrystalline structure was not observed for higher Ni contents (x = 20, 25).(Authors)

  18. NiCo-lead zirconium titanate-NiCo trilayered magnetoelectric composites prepared by electroless deposition

    Directory of Open Access Journals (Sweden)

    M. H. Zhou

    2015-04-01

    Full Text Available The NiCo layers with various Ni/Co atomic ratio have been successfully electroless deposited on PZT layers by varying the bath composition. As the cobalt atomic ratio in the deposited layer increases from 17.2 to 54.8 wt%, the magnetostrictive coefficient decreases. The magnetoelectric effect depends strongly on the magnetostrictive properties of magnetostrictive phase. The magnetoelectric coefficient of NiCo/PZT/NiCo trilayers increases with Ni/Co atomic ratio of the deposited NiCo layers increasing from 45:55 to 83:17. A maximum ME voltage coefficient of αE,31 = 2.8 V ⋅ cm−1 ⋅ Oe−1 is obtained at a frequency of about 88 kHz, which makes these trilayers suitable for applications in actuators, transducers and sensors.

  19. Reduction of a Ni/Spinel Catalyst for Methane Reforming

    DEFF Research Database (Denmark)

    Kehres, Jan; Andreasen, Jens Wenzel; Fløystad, Jostein Bø;

    2015-01-01

    microscopy (HRTEM) was performed on the fresh catalyst sample. The Ni particles in the fresh catalyst sample were observed to exhibit a Ni/NiO core/shell structure. A decrease of the Ni lattice parameter is observed during the reduction in a temperature interval from 413 – 453 K, which can be related to the...

  20. Survey of U-C-Ni ternary diagram

    International Nuclear Information System (INIS)

    U-C-Ni ternary diagram presents, in addition to the intermetallic compounds of U-Ni system and uranium carbides, two mixed carbides UC2Ni and U2C3Ni. The first carbide is decomposed from 1400 deg. C; the second is stable up to 1800 deg. C. (authors)

  1. Study of the central collisions in the reactions Ni + Al and Ni + Ni at 28 A.MeV

    International Nuclear Information System (INIS)

    The work will be presented is in line of characterisation of mechanisms in the energy range of onset of multifragmentation (excitation energy of composed nucleus around 4 - 5 AMeV). This work is focused on an experiment performed at the SARA facility, in Grenoble, using the AMPHORA multi detection array. I have been particularly interested in central collisions in the Ni + Al and Ni + Ni systems. The possibility to detect complete events for Ni + Al, and quasi-complete events for the Ni + Ni case, due to the way AMPHORA has been designed, is the reason of this choice. Furthermore Ni + Ni presents the interest of a symmetrical system, for which the excitation energy per nucleon is maximum. The study of these reactions has been focused on the quasi-complete events (events for which at least 80 % of the total charge has been detected). Heavy ions produced in peripheral collisions are very likely emitted along the beam line or stopped in the plastic detectors, energy thresholds are too high for the quasi-target products detection, consequently by requiring complete or quasi-complete measurement of the total charge, we are able to detect mostly central events. The knowledge of informations like charge, energy or detection angles allows to isolate the source(s) and to reconstruct the size and the excitation energy of the source(s). Comparisons with simulations like sequential emission (GEMINI code), very deep inelastic collision or instantaneous emission (Berliner code) allows to characterise the first stage of the collision (binary collisions or central collisions) and the type of deexcitation of the source(s). Some calculations was also performed with the statistical model code MODGAN. Indeed azimuthal correlations seem to be a good tool in getting more information about involved reaction mechanisms. Comparisons with MODGAN provide information about angular momentum of the source and time delay between emissions of the two particles (separation between sequential or

  2. Substituent effects on 61Ni NMR chemical shifts

    OpenAIRE

    Bühl, Michael; Peters, Dietmund; Herges, Rainer

    2009-01-01

    Ni-61 chemical shifts of Ni(all-trans-cdt) L (cdt = cyclododecatriene, L = none, CO, PMe3), Ni(CO)(4), Ni(C2H4)(2)(PMe3), Ni(cod)(2) (cod = cyclooctadiene) and Ni(PX3)(4) (X = Me, F, Cl) are computed at the GIAO (gauge-including atomic orbitals), BPW91, B3LYP and BHandHLYP levels, using BP86-optimised geometries and an indirect referencing scheme. For this set of compounds, substituent effects on delta(Ni-61) are better described with hybrid functionals than with the pure BPW91 functional. On...

  3. Electrodeposited NiCu Alloy Catalysts for Glucose Oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Lim, Jieun; Park, Hansoo; Kim, Sookil [Chung-Ang Univ., Seoul (Korea, Republic of); Ahn, Sang Hyun; Jang, Jong Hyun [Korea Institute of Science and Technology, Seoul (Korea, Republic of)

    2014-07-15

    NiCu alloys have been suggested as potential candidates for catalysts in glucose oxidation. In this study, NiCu alloys with different compositions were prepared on a glassy carbon substrate by changing the electrodeposition potential to examine the effect of Ni/Cu ratios in alloys on catalytic activity toward glucose oxidation. Cyclic voltammetry and chronoamperometry showed that NiCu alloys had higher catalytic activity than pure Ni and Cu catalysts. Especially, Ni{sub 59}Cu{sub 41} had superior catalytic activity, which was about twice that of Ni at a given oxidation potential. X-ray analyses showed that the oxidation state of Ni in NiCu alloys was increased with the content of Cu by lattice expansion. Ni components in alloys with higher oxidation state were more effective in the oxidation of glucose.

  4. Electrodeposited NiCu Alloy Catalysts for Glucose Oxidation

    International Nuclear Information System (INIS)

    NiCu alloys have been suggested as potential candidates for catalysts in glucose oxidation. In this study, NiCu alloys with different compositions were prepared on a glassy carbon substrate by changing the electrodeposition potential to examine the effect of Ni/Cu ratios in alloys on catalytic activity toward glucose oxidation. Cyclic voltammetry and chronoamperometry showed that NiCu alloys had higher catalytic activity than pure Ni and Cu catalysts. Especially, Ni59Cu41 had superior catalytic activity, which was about twice that of Ni at a given oxidation potential. X-ray analyses showed that the oxidation state of Ni in NiCu alloys was increased with the content of Cu by lattice expansion. Ni components in alloys with higher oxidation state were more effective in the oxidation of glucose

  5. Pt redistribution during Ni(Pt) silicide formation

    International Nuclear Information System (INIS)

    We report on a real-time Rutherford backscattering spectrometry study of the erratic redistribution of Pt during Ni silicide formation in a solid phase reaction. The inhomogeneous Pt redistribution in Ni(Pt)Si films is a consequence of the low solubility of Pt in Ni2Si compared to NiSi and the limited mobility of Pt in NiSi. Pt further acts as a diffusion barrier and resides in the Ni2Si grain boundaries, significantly slowing down the Ni2Si and NiSi growth kinetics. Moreover, the observed incorporation of a large amount of Pt in the NiSi seeds indicates that Pt plays a major role in selecting the crystallographic orientation of these seeds and thus in the texture of the resulting Ni1-xPtxSi film

  6. Modeling and simulation of NiO dissolution and Ni deposition in molten carbonate fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Nam, Suk Woo; Choi, Hyung-Joon; Lim, Tae Hoon [Korea Institute of Science & Technology, Seoul (Korea, Republic of)] [and others

    1996-12-31

    Dissolution of NiO cathode into the electrolyte matrix is an important phenomena limiting the lifetime of molten carbonate fuel cell (MCFC). The dissolved nickel diffuses into the matrix and is reduced by dissolved hydrogen leading to the formation of metallic nickel films in the pores of the matrix. The growth of Ni films in the electrolyte matrix during the continuous cell operation results eventually in shorting between cathode and anode. Various mathematical and empirical models have been developed to describe the NiO dissolution and Ni deposition processes, and these models have some success in estimating the lifetime of MCFC by correlating the amount of Ni deposited in the matrix with shorting time. Since the exact mechanism of Ni deposition was not well understood, deposition reaction was assumed to be very fast in most of the models and the Ni deposition region was limited around a point in the matrix. In fact, formation of Ni films takes place in a rather broad region in the matrix, the location and thickness of the film depending on operating conditions as well as matrix properties. In this study, we assumed simple reaction kinetics for Ni deposition and developed a mathematical model to get the distribution of nickel in the matrix.

  7. Rapid separation of nickel for 59Ni and 63Ni activity measurement in radioactive waste samples

    International Nuclear Information System (INIS)

    A separation procedure of Ni has been described for the quantification of 59Ni and 63Ni in radioactive wastes discharged from nuclear power plants and various research activities related to the nuclear fuel cycle. For a rapid separation of the Ni-nuclides in sixteen sample solutions in 0.2 M NH4-oxalate, a separation system composed of a peristaltic pump with sixteen channels and the same number of Ni-Resin columns was constructed. After sorption of the Ni-nuclides by sequentially passing 100 mL of the sample solution in 0.2 M NH4-oxalate, 130 mL of 0.1 M NH4-oxalate solution and 10 mL of deionized water as a wash into the columns, these were purely recovered by passing 10 mL of 9 M HCl into the Ni-Resin columns stacked in series on the anion exchange resin columns. The separation of the Ni-nuclides in sixteen sample solutions can be achieved within 7 h. The chemical yield of the proposed procedure is 92.3 ± 0.8 % (n = 5) and the gravimetric recovery in the preparation stage of the Ni-nuclide sources is also acceptable, 88.5 ± 1.3 % (n = 5). (author)

  8. Thickness and ordering temperature of surface NiO/Ni systems

    Directory of Open Access Journals (Sweden)

    Ying-Ta Shih

    2014-02-01

    Full Text Available We estimate the thickness and ordering temperature of an antiferromagnetic and passivation surface oxide through exchange bias coupling. The surface NiO, which is generated through the exposure of a Ni/Cu(001 surface to oxygen, is taken as a model system on which to perform the estimation. Since no exchange bias is found in the surface NiO/Ni/Cu(001, we have built a sandwich structure of NiO/n ML Ni/10 ML Co/Cu(001 to measure the n dependence of exchange bias. With n ⩽ 2, a large exchange bias field is found above 300 K, which could be due to the direct contact between the oxides and the Co layer. With 3 ⩽ n ⩽ 6, a smaller exchange bias field is found with a blocking temperature of 190 K. This implies that the thickness of NiO is, at most, 3 ML. Discovering the thickness and ordering temperature of the surface NiO provides us to explore the potential applications by using surface NiO.

  9. Studies on the valence electronic structure of Fe and Ni in FeNi1- alloys

    Indian Academy of Sciences (India)

    D K Basa; S Raj; H C Padhi; M Polasik; F Pawlowski

    2002-05-01

    -to- X-ray intensity ratios of Fe and Ni in pure metals and in FeNi1- alloys ( = 0.20, 0.50, 0.58) exhibiting similar crystalline structure have been measured following excitation by 59.54 keV -rays from a 241Am point source, to understand as to why the properties of permalloy Fe0.2Ni0.8 is distinct from other alloy compositions. It is observed that the valence electronic structure of Fe0.2Ni0.8 alloy is totally different from other alloys which may be attributed to its special magnetic properties.

  10. Differences of transformation behavior between Ni-rich TiNi shape memory films and alloys

    Institute of Scientific and Technical Information of China (English)

    贺志荣; 周敬恩

    2002-01-01

    The differences of transformation behavior between Ni-rich TiNi shape memory film (SMF) and shape memory alloy (SMA) age-treated at 773K after solution-treatment at 973K have been investigated, using Ti-51.5Ni thin film and Ti-51.5Ni bulk alloy as examples, by differential scanning calorimetry (DSC), SEM and EDX. It is found that the age-treated Ni-rich TiNi SMF and SMA are of the same types of transformation, i.e., A→R→M (during cooling), and M→A (during heating) (A: parent phase; R: R-phase; M: martensite); the transformation temperature of the TiNi SMF is lower than that of the SMA, but the SMFs hysteresis is larger. The transformation heat of the TiNi SMF and SMA is nearly the same. The reason that TiNi SMFs strain is sensitive to temperature is not hysteresis, but its thickness is thinner, and the temperature is easy to distribute homogeneously.

  11. Continuum mechanics simulations of NiO/Ni-YSZ composites during reduction and re-oxidation

    DEFF Research Database (Denmark)

    Pihlatie, Mikko; Frandsen, Henrik Lund; Kaiser, Andreas; Mogensen, Mogens Bjerg

    2010-01-01

    analysis of the internal factors leading to the dimensional changes and the thermomechanical instability have been addressed, to our knowledge for the first time, using continuum mechanics simulations. The two intertwined percolating phases, YSZ and NiO/Ni, interact and the driving force for the...... dimensional change arises from the volumetric change related to the phase change NiO ↔ Ni. The measurable change in bulk length is given by the ceramic YSZ backbone as a response to the stress created by the chemical strain. The different subprocesses described in the model for YSZ were elastic and anelastic...

  12. Precipitate size dependence of Ni/Ni3Al interface energy

    International Nuclear Information System (INIS)

    The interface energy of Ni/Ni3Al dictates the morphology of Ni3Al precipitate and thereby the creep resistance of the Ni-base superalloy. Based on classical molecular dynamics simulations, we report that the interface formation energy depends on the size of Ni3Al precipitate. This dependence is non-monotonic below 20 nm, and converges to a constant value beyond 20 nm. Such dependence is a result of competition between the attractive interaction of dislocations from neighboring interfaces and the strain energy in the Ni3Al precipitate. Further, from elasticity theory, taking into account of the effect of misfit strain, a similar transformation behavior of dislocation dipole's elastic energy versus interface distance was also obtained, which shows the transition point of about 6.2 nm. - Highlights: • Here, we reported the precipitate size dependence of Ni/Ni3Al interface energy. • Such dependence is a result of competition between the attractive interaction and the strain energy in Ni3Al phase. • From elasticity theory, taking into account of the effect of misfit strain, a similar transformation behavior occurs

  13. Effect of Mg/Ni ratio on microstructure of Mg–Ni films deposited by magnetron sputtering

    Energy Technology Data Exchange (ETDEWEB)

    Matsuda, Junko, E-mail: junko.matsuda@i2cner.kyushu-u.ac.jp [International Institute for Carbon-Neutral Energy Research (WPI-I2CNER), Kyushu University, Motooka 744, Nishi-ku, Fukuoka 819-0395 (Japan); Uchiyama, Naoki; Kanai, Tomomi; Harada, Kazumi [ATSUMITEC CO., LTD., Ubumi 7111, Yuto-cho, Nishi-ku, Hamamatsu 431-0192 (Japan); Akiba, Etsuo [International Institute for Carbon-Neutral Energy Research (WPI-I2CNER), Kyushu University, Motooka 744, Nishi-ku, Fukuoka 819-0395 (Japan); Department of Mechanical Engineering, Faculty of Engineering, Kyushu University, Motooka 744, Nishi-ku, Fukuoka 819-0395 (Japan)

    2014-12-25

    Highlights: • Hydrogenation/dehydrogenation properties of Mg–Ni films depend on the Mg/Ni ratio. • Mg{sub 6}Ni films are composed of Mg-rich amorphous matrix and Mg{sub 2}Ni nanocrystals. • Mg{sub 2}Ni is fully amorphous, in contrast Mg crystallization occurs in Mg{sub 10}Ni films. • Mg{sub 6}Ni films after hydrogenation include Mg{sub 2}NiH{sub 4}, MgH{sub 2} and Mg crystals. • Mg crystallization causes to reduce desorption kinetics and cycle ability. - Abstract: The relationship between the Mg/Ni ratio and microstructure of Mg–Ni films with a Pd-cap deposited by magnetron sputtering is investigated using transmission electron microscopy. As a result, the 6Mg–Ni films are observed to be composed of a Mg-rich amorphous matrix and Mg{sub 2}Ni nanocrystals. In contrast, the 10Mg–Ni films contain Mg nanocrystals and Mg-rich amorphous. The 2Mg–Ni films, which absorb/desorb hydrogen repeatedly as well as 6Mg–Ni films, are fully amorphous and have a homogeneous distribution of Mg and Ni. The hydrogenated 6Mg–Ni film, after 200 cycles of hydrogenation/dehydrogenation, includes Mg{sub 2}NiH{sub 4} and MgH{sub 2} nanocrystals as well as Mg crystals. In conclusion, the crystallization of Mg reduces desorption kinetics and cycle ability of the Mg–Ni films. Our results suggested that Mg crystallization occurs in films with an initial Mg/Ni ratio greater than 7.7 the eutectic composition between Mg and Mg{sub 2}Ni.

  14. Prospect of MH-Ni Batteries Development

    Institute of Scientific and Technical Information of China (English)

    Xu Shaoping; Xing Zhiqiang; Liang Wanlong; Ma Yijun

    2004-01-01

    The development trend and promising application prospects of high-power MH-Ni battery were reviewed by studying and comparing the current high-power batteries research area.High-power MH-Ni batiery has good performlife with 500 ~ 1000 times, abundant material resource, especially abundant rare earth resource in China, high-rate discharging, rapid charging, good safety as well as no pollution, etc., which is regarded as the most promising storage battery for electric vehicles.The performance of high power MH-Ni battery can be brought into play fully and ensure electric vehicles performance if it is equipped with appropriate chargers, controlling system and electric motors.Facing opportunities and challenges, MH-Ni battery has promising application prospects on hybrid electric automobile, electric bicycle and a variety of small sized electric vehicles by improving its technology constantly and developing market actively.

  15. [Ni II] emission in supernova remnants

    International Nuclear Information System (INIS)

    Combining new spectrophotometric data on the Orion and Crab Nebulae with detailed calculations, the authors show that strong [Ni II] λ7378 emission observed in numerous SNR's may be associated with gas having Ne > 50,000 cm-3

  16. Ni adsorption and Ni-Al LDH precipitation in a sandy aquifer: An experimental and mechanistic modeling study

    NARCIS (Netherlands)

    Regelink, I.C.; Temminghoff, E.J.M.

    2011-01-01

    Mining activities and industries have created nickel (Ni) contaminations in many parts of the world. The objective of this study is to increase our understanding of Ni adsorption and Nickel-Aluminium Layered Double Hydroxide (Ni-Al LDH) precipitation to reduce Ni mobility in a sandy soil aquifer. At

  17. Amorphous Ni-P Hollow Spheres Prepared by Self-assembly of Ni-P Nanoparticles on Polystyrene Beads

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The first preparation of amorphous Ni-P/PS (polystyrene) core-shell and Ni-P hollow microspheres was per-formed using a surface seeding-electroless plating method. The preliminary magnetic properties of the amorphous Ni-P hollow sphere were investigated and compared with those of the Ni hollow sphere.

  18. Preparation of C/Ni-NiO composite nanofibers for anode materials in lithium-ion batteries

    Science.gov (United States)

    Luo, Chenghao; Lu, Weili; Li, Yu; Feng, Yiyu; Feng, Wei; Zhao, Yunhui; Yuan, Xiaoyan

    2013-11-01

    Carbon nanofibers (CNFs) embedded with various amounts of Ni and NiO nanoparticles (C/Ni-NiO) were prepared by electrospinning of polyacrylonitrile (PAN), followed by heat treatment. The structure and composition of the obtained C/Ni-NiO composite nanofibers were analyzed by scanning electron microscopy, transmission electron microscopy, and X-ray diffraction. The results suggested that the morphology, nanofiber diameter, and the content of the Ni-NiO nanoparticles in the CNFs were controlled by different amounts of nickel acetate added into the PAN. The electrochemical measurements of a charge/discharge experiment and a cyclic voltammetry test indicated that the content and the size of Ni-NiO nanoparticles embedded in the CNFs had a great influence on the electrochemical performance of lithium-ion batteries. CNFs embedded with a certain content of Ni-NiO nanoparticles as binder-free anodes for rechargeable lithium-ion batteries exhibited improved electrochemical performance, including high reversible capacities, good capacity retention, and stable cycling performance. This is mainly ascribed to the formation of a well-distributed Ni-NiO nanoparticle structure and the buffering role of the carbon nanofiber matrix, together with the high theoretical capacity of NiO and the increase in electrode connectivity caused by the formation of electrochemically inactive Ni nanoparticles.

  19. Density functional theory study of the interfacial properties of Ni/Ni{sub 3}Si eutectic alloy

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Yuhong, E-mail: zyh388@sina.com [College of Materials Science and Engineering, North University of China, Taiyuan 030051 (China); Wen, Zhiqin; Hou, Hua; Guo, Wei [College of Materials Science and Engineering, North University of China, Taiyuan 030051 (China); Han, Peide [College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024 (China)

    2014-06-01

    In order to clarify the heterogeneous nucleation potential of α-Ni grains on Ni{sub 3}Si particles in Ni-Ni{sub 3}Si eutectic alloy, the work of adhesion (W{sub ad}), fracture toughness (G), interfacial energy (γ{sub i}), and electronic structure of the index (0 0 1), (1 1 0) and (1 1 1) Ni/Ni{sub 3}Si interfaces with two different cohesive manners are investigated using first-principles method based on density functional theory. Results indicate that the center site stacking sequence (OM) is preferable to continue the natural stacking sequence of bulk Ni and Ni{sub 3}Si. Since OM stacking interfaces have larger W{sub ad}, G and γ{sub i} than that of the top site stacking (OT) interfaces. The Ni/Ni{sub 3}Si (1 1 0) interface with OM stacking has the best mechanical properties. Therefore, the formation of this interface can improve the stability, ductility and fracture toughness of Ni-Ni{sub 3}Si eutectic alloy. The calculated interfacial energy of Ni/Ni{sub 3}Si (0 0 1), (1 1 0) and (1 1 1) interfaces with OM stacking proves the excellent nucleation potency of Ni{sub 3}Si particles for α-Ni phase from thermodynamic considerations. Besides, the electronic structure and chemical bonding of (1 1 0) interface with OM stacking are also discussed.

  20. Nuclear magnetic resonance in LaNi/sub 5/

    Energy Technology Data Exchange (ETDEWEB)

    Rubinstein, M.; Swartzendruber, L.J.; Bennett, L.H.

    1979-03-01

    Proton and La/sup 139/ nuclear magnetic resonance measurements have been performed on LaNi/sub 5/, LaNi/sub 5/ hydrides, and LaNi/sub 5/H/sub x/ with ternary additions. With ternary additions, the activation energy for proton diffusion remained unchanged, but the motionally narrowed linewidth broadened. The quadrupole interaction on the La site has been determined in LaNi/sub 5/ and LaNi/sub 5/H/sub x/.

  1. The ternary system Tm-Ni-In at 870 K

    Energy Technology Data Exchange (ETDEWEB)

    Tyvanchuk, Yuriy B.; Kalychak, Yaroslav M. [Ivan Franko National University of Lviv (Ukraine). Dept. of Analytical Chemistry; Lukachuk, Maryana; Poettgen, Rainer [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie; Szytula, Andrzej [Jagiellonian Univ., Krakow (Poland). Inst. of Physics

    2015-11-01

    The isothermal section of the Tm-Ni-In system at T = 870 K was constructed. Nine ternary compounds: Tm{sub 10}Ni{sub 9}In{sub 20}, TmNi{sub 1-0.60}In{sub 1-1.40}, Tm{sub 2}Ni{sub 2}In, Tm{sub 2}Ni{sub 1.78}In, Tm{sub 5}Ni{sub 2}In{sub 4}, Tm{sub 11}Ni{sub 4}In{sub 9}, Tm{sub 4.83}Ni{sub 2}In{sub 1.17}, Tm{sub 6}Ni{sub 2}In and Tm{sub 14}Ni{sub 3}In{sub 3} exist in the system at the temperature of investigation. Solid solutions with In/Ni and Tm/In mixing were noticed for numerous compounds. A broad substitution of Ni for In was observed for TmNi{sub 1-0.60}In{sub 1-1.40}, and of Tm for In for the TmNi{sub 2}-TmNi{sub 4}In section. An interstitial solid solution Tm{sub x}NiIn, based on binary equiatomic NiIn, extends up to 8 at.% Tm (x = 0.17). The magnetic properties of TmNiIn, Tm{sub 2}Ni{sub 2}In and Tm{sub 5}Ni{sub 2}In{sub 4} are also reviewed.

  2. Domain structure and magnetization process of a giant magnetoimpedance geometry FeNi/Cu/FeNi(Cu)FeNi/Cu/FeNi sensitive element

    International Nuclear Information System (INIS)

    The magnetization process and the magnetic domains of the FeNi (100 nm)/Cu (2.5 nm)/FeNi (100 nm)/Cu (480 nm)/FeNi (100 nm)/Cu (2.5 nm)/FeNi (100 nm) structure were studied. This geometry consists of two FeNi/Cu/FeNi trilayers with a thick in the direction perpendicular to the plane of the sensitive element and narrow in the direction of the flowing current Cu electrode in the centre. Ferromagnet/conductor/ferromagnet is the typical geometry of magnetoimpedance thin-film-based sensitive elements used to detect small magnetic fields. Multilayered structures were prepared by rf-sputtering in a magnetic field of 100 Oe applied perpendicular to the Cu electrode in order to induce transverse magnetic anisotropy. The magnetic measurements and magnetic domain structure observations were made in magnetic fields applied one at a time parallel or perpendicular to the Cu electrode. Different magnetization processes with non-homogeneous rotations in the first case and dominant multiple nucleation and merging of domains in the second one were observed

  3. Ni2+ doping DNA: a semiconducting biopolymer

    International Nuclear Information System (INIS)

    DNA is a one-dimensional nanowire in nature, and it may not be used in nanodevices due to its low conductivity. In order to improve the conducting property of DNA, divalent Ni2+ are incorporated into the base pairs of DNA at pH≥8.5 and nickel DNA (Ni-DNA) is formed. Conducting scanning probe microscopy (SPM) analysis reveals that the Ni-DNA is a semiconducting biopolymer and the Schottky barrier of Ni-DNA reduces to 2 eV. Meanwhile, electrochemical analysis by cyclic voltammetry and AC impedance shows that the conductance of Ni-DNA is better than that of native DNA by a factor of approximately 20-fold. UV spectroscopy and DNA base pair mismatch analyses show that the conducting mechanism of Ni-DNA is due to electrons hopping through the π-π stacking of DNA base pairs. This biomaterial is a designable one-dimensional semiconducting polymer for usage in nanodevices

  4. Structural Investigation of Fe-Ni-S and Fe-Ni-Si Melts by High-temperature Fluorescence XAFS Measurements

    Energy Technology Data Exchange (ETDEWEB)

    Manghnani, M.; Hong, X.; Newville, M.; Balogh, J. (Hawaii); (UC)

    2007-03-01

    Iron-nickel (Fe-Ni) alloy is regarded as the most abundant constituent of Earth's core, with an amount of 5.5 wt% Ni in the core based on geochemical and cosmochemical models. The structural role of nickel in liquid Fe-Ni alloys with light elements such as S or Si is poorly understood, largely because of the experimental difficulties of high-temperature melts. Recently, we have succeeded in acquiring Ni K-edge fluorescence x-ray absorption fine structure (XAFS) spectra of Fe-Ni-S and Fe-Ni-Si melts and alloys. Different structural environment of Ni atoms in Fe-Ni-S and Fe-Ni-Si melts is observed, supporting the effect of light elements in Fe-Ni melts.

  5. Alpha Ni optical model potentials

    Science.gov (United States)

    Billah, M. M.; Abdullah, M. N. A.; Das, S. K.; Uddin, M. A.; Basak, A. K.; Reichstein, I.; Sen Gupta, H. M.; Malik, F. B.

    2005-11-01

    The present work reports the analyses of the experimental differential cross-sections of α elastic scattering on 58,60,62,64Ni, over a wide range of incident energies, in terms of four types of optical potentials, namely shallow (molecular), deep non-monotonic, squared Woods-Saxon and semi-microscopic folding. All the four potentials produce a reasonable description of the experimental data. The potential parameters, calculated from the energy density functional theory using a realistic two-nucleon interaction, resemble closely the molecular potential parameters, which produce the best description of the experimental data for the four isotopes. The volume integrals and the energy variation of the parameters indicate the effect of the shell-model structure on the potentials. The folding potentials, without any need for renormalization, are found to describe reasonably well the elastic scattering cross-section data for the four isotopes within the energy range considered. In conformity with the previous observation on Ca isotopes, the number of nucleons, 4A=49, existing in α-like clusters in the target nucleus, is the same for the four isotopes, considered herein.

  6. The formation model of Ni-Cr oxides on NiCoCrAlY-sprayed coating

    International Nuclear Information System (INIS)

    The atomic arrangement and distribution of oxides (Cr2O3, NiCr2O4 and NiO) on the sprayed-NiCoCrAlY coating after oxidation are analyzed. The formation and the growth model of Ni-Cr oxide phases are discussed according to the matching relationship between atoms. The outline character and a scale of spinel NiCr2O4 are discussed. The results show that Cr atoms can form two close-packed arrangements in the crystal plane of Cr2O3 perpendicular to orientation. The atomic spacing in the first arrangement corresponds to double that of Ni/Ni3Al in {1 1 1} crystal face. This suggests that Ni/Ni3Al is the substrate for Cr2O3 to grow along direction. The lattice mismatch between Cr2O3 and Ni/Ni3Al is less than that of Al2O3, which indicates that Cr2O3 is easier to form than Al2O3 during the oxidation process. The atomic spacing in another close-packed arrangement of Cr2O3 perpendicular to orientation is approximately equal to that of Ni or Cr in the plane of NiCr2O4 and NiO perpendicular to orientation. So Cr2O3 can be the substrate for NiCr2O4 and NiO to grow in the direction. NiCr2O4 and NiO can grow directly along the orientation on each other. NiCr2O4 can grow outward in the planes of Cr2O3 perpendicular to and grow inward along orientation of NiO.

  7. Recrystallization textures of powder metallurgically prepared pure Ni, Ni-W and Ni-Mo alloy tapes for use as substrates for coated superconductors

    International Nuclear Information System (INIS)

    Development of cube texture after heavy cold deformation and annealing has been studied in powder metallurgically prepared pure Ni, Ni-5at.%Mo and Ni-5at.%W alloys for use as substrates for coated superconductor applications. Two grades of Ni powder with different purities have been used to prepare the initial materials. Addition of W and Mo is found to be beneficial in increasing the volume fraction of the cube component, irrespective of the purity of the Ni powder used. W particularly increases the volume fraction of the cube component in Ni by decreasing the volume fraction of the RD (rolling direction)-rotated cube grains. Studies on partially recrystallized samples indicate that in contrast to pure Ni, in Ni-5at.%W alloy the recrystallized grains are mostly cube oriented right from the beginning of recrystallization

  8. X-ray study of TiNiSn and ZrNiSn intermetallics oxidation

    International Nuclear Information System (INIS)

    Phases formed in the process of oxidizing TiNiSn and ZrNiSn in air at progressively elevated temperatures have been studied by X-ray powder diffraction. The oxidation was found to proceed by different paths for the two isostructural compounds. A general scheme of the oxidation reactions was proposed. (orig.)

  9. The Ni-rich Part of the Ni-P-Sn System: Isothermal Sections

    Science.gov (United States)

    Schmetterer, C.; Vizdal, J.; Kroupa, A.; Kodentsov, A.; Ipser, H.

    2009-11-01

    Due to the use of phosphorus-containing nickel substrates in microelectronics, understanding of their reaction with Sn-based solders and knowledge of the corresponding reaction products is highly important. Therefore the ternary Ni-P-Sn system was investigated experimentally using x-ray diffraction (XRD), scanning electron microscopy (SEM) + energy dispersive x-ray spectroscopy (EDX)/wavelength-dispersive x-ray spectroscopy (WDS), and differential thermal analysis (DTA). Sample preparation was done by alloying powders of the starting components contained in alumina crucibles in evacuated quartz tubes. In this study the phase equilibria in the Ni-rich part of the ternary Ni-P-Sn system are described in the form of three partial isothermal sections at 550°C, 700°C, and 850°C. A total of five ternary compounds exist in the Ni-rich part, and the binary Ni3Sn2 HT phase was found to dissolve 17.6 at.% P at 850°C. This well agrees with literature reports, while a different extent and shape of the large homogeneity range of this phase were found. Between 850°C and 700°C phase equilibria change significantly due to the formation of the ternary phases Ni10P3Sn5 (T3), Ni13P3Sn8 (T4), and Ni2PSn (T5).

  10. Ni(salen): a system that forms many solvates with interacting Ni atoms

    NARCIS (Netherlands)

    Siegler, M.A.M.; Lutz, M.

    2009-01-01

    Recrystallization of [N,N’-Ethylene-bis(salicylideneiminato)]-nickel(II) [Ni(salen)] has been carried out from a large selection of solvents. Crystals can be either solvent free or solvates. This study is based on X-ray crystal structure determinations, which include the redetermination of Ni(salen)

  11. Investigation on microstructures of NiO-YSZ composite and Ni-YSZ cermet for SOFCs

    Energy Technology Data Exchange (ETDEWEB)

    Talebi, Tahereh; Sarrafi, Mohammad Hassan; Haji, Mohsen; Raissi, Babak; Maghsoudipour, Amir [Materials and Energy Research Center, Karaj, Tehran 14155-4777 (Iran)

    2010-09-15

    NiO-YSZ composites and Ni-YSZ cermets were successfully performed for solid oxide fuel cell applications. These composites must have enough porosity and appropriate microstructure for transferring the fuel gases. In this study, ball-milling was used as a simple, cost-effective method for the purpose of mixing the raw materials. The homogeneity of NiO-YSZ composites was examined by Map mode of SEM. NiO-YSZ composites were reduced at the high temperature under the controlled atmosphere to fabricate Ni-YSZ cermet. Variations in the anode phases were investigated by XRD and microstructure and porosity of composites were observed by SEM. Effective parameters like temperatures and the amount of pore former were investigated on open porosity, bulk density, electrical conductivity as well as electrochemical impedance of NiO-YSZ composites and Ni-YSZ cermet. A thin layer of YSZ was deposited by EPD as an electrolyte on NiO-YSZ composites which had various amount of open porosity, to study its effect on the performance of semi-cells by electrochemical impedance. (author)

  12. Combustion Synthesis of NiAl and In-situ Joining to Ni-based Superalloy

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Combustion synthesis is used as a joining technology to join Ni-based superalloys with in-situ synthesized NiAl filler. The synthesis mechanism is discussed. The microstructure of the joints is investigated and the joint strength is also evaluated by tensile testing.

  13. Reduction mechanism of Ni2+ into Ni nanoparticles prepared from different precursors: Magnetic studies

    Indian Academy of Sciences (India)

    R S Ningthoujam; N S Gajbhiye; Sachil Sharma

    2009-03-01

    The reduction mechanism of Ni2+ into Ni particles using different precursors such as NiCl2 solution, NiO powder and Ni[(NH3)6]Cl2 complex has been established. Different particle sizes can be designed from these precursors. The smallest crystallite size (12 nm) can be obtained from Ni[(NH3)6]Cl2 complex in the presence of the stabilizing ligand (oleic acid). The field-cooled (FC) and zero-field-cooled (ZFC) magnetization of Ni particles obtained from Ni[(NH3)6]Cl2 complex in the temperature range 5–300 K established the ferromagnetic interaction up to 300 K. The magnetization values at three different temperatures 5, 70 and 300 K are 50.2, 49.5 and 45.5 Oe respectively at 3 × 104 Oe applied field and such values are less than that of the bulk value. The Curie temperature (c) decreases slightly with the decrease of particle size. This study will provide guidance in the preparation of metal nanoparticles from different precursors.

  14. Probing the semi-magicity of $^{68}$Ni via the $^{3}$H($^{66}$Ni,$^{68}$Ni)p two-neutron transfer reaction in inverse kinematics

    CERN Multimedia

    Reiter, P; Blazhev, A A; Kruecken, R; Franchoo, S; Mertzimekis, T; Darby, I G; Van de walle, J; Raabe, R; Elseviers, J; Gernhaeuser, R A; Sorlin, O H; Georgiev, G P; Bree, N C F; Habs, D; Chapman, R; Gaudefroy, L; Diriken, J V J; Jenkins, D G; Kroell, T; Axiotis, M; Huyse, M L; Patronis, N

    We propose to perform the two-neutron transfer reaction $^{3}$H($^{66}$Ni, $^{68}$Ni)$p$ using the ISOLDE radioactive ion beam at 2.7 $A$ MeV and the MINIBALL + T-REX setup to characterize the 0$^{+}$ and 2$^{+}$ states in $^{68}$Ni.

  15. Hydrides of CeNi5, MmNi5, Ca02(Ce065Mm035)08Ni5, Ca02Ce08Ni5, Ca02Mm08Ni5, and mixed CeNi5/MmNi5

    International Nuclear Information System (INIS)

    Six intermetallic alloys [CeNi5, MmNi5, Ca02(Ce065Mm035)08Ni5, Ca02Ce08Ni5, Ca02Mm08Ni5, and a mixed alloy, CeNi5/MmNi5] were investigated with respect to their suitability to provide high hydrogen capacity and their potential for use in providing substantial hydrogen pressure at both low and high temperatures. A second phase of our investigation dealt with ball-milling and hydriding and dehydriding cycles to produce fine particles for use in hydride powder transfer studies. A summary of several Van't Hoff plots is also included for hydride-forming alloys

  16. The first principle study of Ni2ScGa and Ni2TiGa

    International Nuclear Information System (INIS)

    We computed the electronic structure, elastic moduli, vibrational properties, and Ni2TiGa and Ni2ScGa alloys in the cubic L21 structure. The obtained equilibrium lattice constants of these alloys are in good agreement with available data. In cubic systems, there are three independent elastic constants, namely C11, C12 and C44. We calculated elastic constants in L21 structure for Ni2TiGa and Ni2ScGa using the energy-strain method. The electronic band structure, total and partial density of states for these alloys were investigated within density functional theory using the plane-wave pseudopotential method implemented in Quantum-Espresso program package. From band structure, total and projected density of states, we observed metallic characters of these compounds. The electronic calculation indicate that the predominant contributions of the density of states at Fermi level come from the Ni 3d states and Sc 3d states for Ni2TiGa, Ni 3d states and Sc 3d states for Ni2ScGa. The computed density of states at Fermi energy are 2.22 states/eV Cell for Ni2TiGa, 0.76 states/eV Cell for Ni2ScGa. The vibrational properties were obtained using a linear response in the framework at the density functional perturbation theory. For the alloys, the results show that the L21 phase is unstable since the phonon calculations have imagine modes

  17. Oxide Scales Formed on NiTi and NiPtTi Shape Memory Alloys

    Science.gov (United States)

    Smialek, James L.; Garg, Anita; Rogers, Richard B.; Noebe, Ronald D.

    2011-01-01

    Ni-49Ti and Ni-30Pt-50Ti (at.%) shape memory alloys were oxidized isothermally in air over the temperature range of 500 to 900 C. The microstructure, composition, and phase content of the scales were studied by SEM, EDS, XRD, and metallography. Extensive plan view SEM/EDS identified various features of intact or spalled scale surfaces. The outer surface of the scale was a relatively pure TiO2 rutile structure, typified by a distinct highly striated and faceted crystal morphology. Crystal size increased significantly with temperature. Spalled regions exhibited some porosity and less distinct features. More detailed information was obtained by correlation of SEM/EDS studies of 700 C/100 hr cross-sections with XRD analyses of serial or taper-polishing of plan surfaces. Overall, multiple layers exhibited graded mixtures of NiO, TiO2, NiTiO3, Ni(Ti) or Pt(Ni,Ti) metal dispersoids, Ni3Ti or Pt3Ti depletion zones, and substrate, in that order. The NiTi alloy contained a 3 at.% Fe impurity that appeared in embedded localized Fe-Ti-rich oxides, while the NiPtTi alloy contained a 2 v/o dispersion of TiC that appeared in lower layers. The oxidation kinetics of both alloys (in a previous report) indicated parabolic growth and an activation energy (250 kJ/mole) near those reported in other Ti and NiTi studies. This is generally consistent with TiO2 existing as the primary scale constituent, as described here.

  18. Preparation of NiO–Ni/natural graphite composite anode for lithium ion batteries

    International Nuclear Information System (INIS)

    Highlights: ► We prepare NiO–Ni/natural graphite composite anode for lithium ion battery. ► The composite shows enhanced cycle stability and capacity than NiO–Ni/acetylene black. ► Enhanced cycle stability is due to the fine electronic conductivity of natural graphite. ► Improved capacity is due to the capacity contribution of natural graphite. -- Abstract: Natural graphite was introduced into NiO–Ni that prepared via a simple pyrogenation method to improve the electrochemical performance of the composite due to the advantages of natural graphite over other amorphous carbon materials in terms of fine electronic conductivity, abundance in nature, low cost and better performance of lithium ion storage. The electrochemical performance of the composite as anode for lithium ion battery was characterized via conventional charge/discharge test and cyclic voltammetric measurement. It shows initial discharge and charge capacity of 630 and 478 mAh g−1 at charge/discharge rate of 0.15 C, maintaining of 532 and 522 mAh g−1 after 100 cycles. It can deliver initial discharge and charge capacity of 508 and 504 mAh g−1 at 0.25 C. After 40 cycles at various rates from 0.25 to 2.5 C, the electrode can restore discharge and charge capacity of 472 and 467 mAh g−1 while lowering the charge/discharge rate to 0.25 C. The electrochemical performance of the NiO–Ni/natural graphite composite was compared with that of NiO–Ni/acetylene black, showing much improvement on cycle stability, specific capacity and rate capability

  19. Tuning the magnetic properties of multisegmented Ni/Cu electrodeposited nanowires with controllable Ni lengths

    Science.gov (United States)

    Susano, M.; Proenca, M. P.; Moraes, S.; Sousa, C. T.; Araújo, J. P.

    2016-08-01

    The fabrication of segmented Ni/Cu nanowires (NWs), with tunable structural and magnetic properties, is reported. A potentiostatic electrodeposition method with a single electrolytic bath has been used to fabricate multisegmented Ni/Cu NWs inside a highly hexagonally ordered anodic nanoporous alumina membrane, with diameters of 50 nm and Ni segment lengths (L Ni) tuned from 10 nm up to 140 nm. The x-ray diffraction results evidenced a strong dependence of the Ni NWs crystallographic face-centered-cubic (fcc) texture along the [220] direction on the aspect ratio of the NWs. The magnetic behavior of the multisegmented Ni/Cu NW arrays, as a function of the magnetic field and temperature, is also studied and correlated with their structural and morphological properties. Micromagnetic simulations, together with the experimental results, showed a dominant antiferromagnetic coupling between Ni segments along the wire length for small low aspect-ratio magnetic segments. When increasing the Ni segments’ length, the magnetic interactions between these along the wire became stronger, favouring a ferromagnetic coupling. The Curie temperature of the NWs was also found to strongly depend on the Ni magnetic segment length. Particularly the Curie temperature was found to be reduced 75 K for the 20 nm Ni segments, following the finite-size scaling relation with ξ 0 = 8.1 Å and γ = 0.48. These results emphasize the advantages of using a template assisted method to electrodeposit multilayer NWs, as it allows an easy tailor of the respective morphological, chemical, structural and magnetic properties.

  20. Exchange bias effect in polycrystalline NiO/NiMn{sub 2}O{sub 4} composite

    Energy Technology Data Exchange (ETDEWEB)

    Freitas Cabral, A.J. [Instituto de Ciências Exatas e Naturais, Universidade Federal do Pará (UFPA), Belém, PA (Brazil); Peña Serna, J.; Rache Salles, B.; Novak, M.A. [Instituto de Física, Universidade Federal do Rio de janeiro (UFRJ), Rio de Janeiro, RJ (Brazil); Pinto, A.L. [Centro Brasileiro de Pesquisas Físicas (CBPF), Rio de Janeiro, RJ (Brazil); Rocha Remédios, C.M. [Instituto de Ciências Exatas e Naturais, Universidade Federal do Pará (UFPA), Belém, PA (Brazil)

    2015-05-05

    Highlights: • Antiferromagnetic NiO/ferrimagnetic NiMn{sub 2}O{sub 4} oxide composites. • Grains are well faceted, indicating that the specimen was well crystallized. • The micrographs suggests that NiO and NiMn{sub 2}O{sub 4} may be stuck to each other. • EB effect in NiO/NiMn{sub 2}O{sub 4} oxide composites. • EB effect increases with the amount of NiO. - Abstract: Calcination of aqueous solutions formed by different molar ratios between the nickel and manganese chlorides led to the formation of antiferromagnetic NiO/ferrimagnetic NiMn{sub 2}O{sub 4} oxide composites, as determined by X-ray powder diffraction technique and Rietveld refinement. Low temperature zero field cooled and field cooled magnetic hysteresis cycles show an exchange bias effect, presumably due to interaction at the interfaces between the antiferromagnetic and ferrimagnetic materials.

  1. Corrosion performance of bi-layer Ni/Cr2C3-NiCr HVAF thermal spray coating

    Science.gov (United States)

    Sadeghimeresht, E.; Markocsan, N.; Nylén, P.; Björklund, S.

    2016-04-01

    The corrosion behavior of three HVAF thermal spray coating systems (A: single-layer Ni, B: single-layer Cr2C3-NiCr coatings, and C: bi-layer Ni/Cr2C3-NiCr coating) was comparatively studied using immersion, salt spray, and electrochemical tests. Polarization and EIS results showed that the corrosion behavior of Cr2C3-NiCr coatings in 3.5 wt.% NaCl solution was significantly improved by adding the intermediate layer of Ni. It was illustrated that the polarization resistance of the bi-layer Ni/Cr2C3-NiCr and single-layer Cr2C3-NiCr coatings were around 194 and 38 kΩ cm2, respectively. Microstructure analysis revealed that the bond coating successfully prevented the corrosion propagation toward the coating.

  2. Electrochemical behavior of Ni(II)/Ni in a hydrophobic amide-type room-temperature ionic liquid

    International Nuclear Information System (INIS)

    Electrochemical reaction of Ni(II)/Ni was investigated in a hydrophobic room-temperature ionic liquid, 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)amide (BMPTFSA) containing Ni(TFSA)2 as a Ni source. The UV-vis spectra showed that Ni(II) in BMPTFSA is octahedrally coordinated with TFSA- anions. The average activation energy for the diffusion coefficients of this Ni(II) complex was ∼26 kJ mol-1, which was close to that for the viscosity. The diffusion coefficient of Ni(II) was estimated to be 9.3 x 10-8 cm2 s-1. Chronoamperometric measurements showed that the electrodeposition of Ni on a platinum substrate involved three-dimensional instantaneous nucleation under diffusion control at room-temperature. The electrodeposits obtained by galvanostatic electrolysis with the current density of -0.046 mA cm-2 at 70 and 100 deg. C were identified as metallic Ni by XRD.

  3. Hydrogen absorption kinetics and structural properties of Mg85Ni10Ca5 and Mg90Ni10

    International Nuclear Information System (INIS)

    Mg85Ni10Ca5 and Mg90Ni10 were prepared by melting mixtures of the elements in mild steel crucibles and pouring them into copper molds. Hydrogen absorption kinetics and structural properties of the alloys were characterized by the volumetric method using a Sievert's apparatus, X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The crystallite size of Mg in Mg85Ni10Ca5, which is evaluated by XRD peak broadening, is about 50% smaller than that in Mg90Ni10. In addition, the nanometer-scale structure composed of Mg, Mg2Ni, Mg2Ca was observed in Mg85Ni10Ca5. Mg85Ni10Ca5 shows better hydrogen absorption kinetics than Mg90Ni10 in the temperature range of room temperature to 573 K. The better absorption kinetics of Mg85Ni10Ca5 is mainly attributed to the nanometer-scale structure

  4. 2-D ACAR measurements of Ni3A1

    International Nuclear Information System (INIS)

    In connection with a detailed study of the electronic structure and stability of the aluminides (Ni,Fe)3Al, 2-D ACAR positron annihilation measurements were made on a Ni3Al single crystal to study the Fermi surface. The results for Ni3Al have been compared with results for pure Ni. Strong similarities were found for the electronic structures of these materials. Theoretical calculations of the Fermi surface for Ni3Al are in good agreement with the experimental results. The Γ16 sheet, not previously observed in any experiment, has now been observed for the first time in Ni3Al. 14 refs., 10 figs

  5. Solidification shrinkage of Ni-Cr alloys

    Energy Technology Data Exchange (ETDEWEB)

    Xiao Feng [Materials Interfacial Physical-Chemistry Research Institute, Chongqing Institute of Technology, No. 4 Xingsheng Road, Yangjiaping, Chongqing 400050 (China); Yang Renhui [Materials Interfacial Physical-Chemistry Research Institute, Chongqing Institute of Technology, No. 4 Xingsheng Road, Yangjiaping, Chongqing 400050 (China)]. E-mail: yangrh2004@21cn.com; Fang Liang [Department of Applied Physics, Chongqing University, No. 174 Shazhong Road, Shapingba, Chongqing 400044 (China); Zhang Chi [Materials Interfacial Physical-Chemistry Research Institute, Chongqing Institute of Technology, No. 4 Xingsheng Road, Yangjiaping, Chongqing 400050 (China)

    2006-07-25

    Ni-Cr superalloy is widely used in casting of critical components in gas-turbine engines. Because of the significant change in density of alloy in mushy state, porosity is likely to arise in the alloy parts due to the solidification shrinkage. On the other hand, because Ni-Cr alloy is very hard and difficult to be machined, the net-shape casting of the alloy is a cheap process. Therefore, it is essential to measure the solidification shrinkage of mushy alloy for obtaining low-cost net-shape casting ingot without inner porosity. However, there have been a few reports on the solidification shrinkage of the liquid Ni-Cr alloy. In this work, the solidification shrinkage of Ni-Cr alloy was calculated by measuring its density using modified sessile drop method. It has been found that, for Ni-(0-24.53)% Cr alloys, the solidification shrinkage value fluctuates in the range of 0.91-2.02% and it tends to increase with increasing Cr concentration in 0-10% Cr. However, for Cr concentration more than 10%, the solidification shrinkage holds on a certain value of 2.00%.

  6. Effect of silicon on oxidation of Ni-15Al alloy

    Institute of Scientific and Technical Information of China (English)

    WU Ying; NIU Yan; WU Wei-tao

    2005-01-01

    The oxidation of binary Ni-Al alloy containing 15% (mole fraction, the same below if not mentioned)Al (Ni-15Al), and of a ternary alloy with the same Al content but also containing 4% Si (Ni-4Si-15Al) has been studied at 1 000 ℃ under 1.0× 105Pa O2 to examine the effect of the addition of Si on the oxidation of Ni-15Al. Oxidation of Ni-15Al produces a duplex scale composed of an outer NiO layer and an inner layer riched in Al2O3. On the contrary, Ni-4Si-15Al forms an external alumina layer directly in contact with the alloy presenting only trace of NiO and the Ni-Al spinel. As a result, the kinetics of Ni-15Al shows a fast initial stage followed by two subsequent parabolic stages with decreasing rate constants, while Ni-4Si-15Al presents essentially a single nearly-parabolic behavior with a rate constant similar to that of the final stage of Ni-15Al. Therefore, the addition of 4% Si significantly reduces the oxidation rate during the initial stage by preventing the formation of Ni-riched scales and promoting an earlier development of an exclusive external alumina layer on the alloy surface.

  7. Transformation to Ni5Al3 in a 63.0 at. pct Ni-Al alloy

    Science.gov (United States)

    Khadkikar, P. S.; Locci, I. E.; Vedula, K.; Michal, G. M.

    1993-01-01

    Microstructures of 63 at. pct P/M Ni-Al alloys with a composition close to the stoichiometry of the Ni5Al3 phase were investigated using homogenized and quenched specimens aged at low temperatures for various times. Results of analyses of XRD data and electron microscopy observations were used for quantitative phase analysis, performed to calculate the (NiAl + Ni5Al3)/Ni5Al3 phase boundary locations. The measured lattice parameters of Ni5Al3 phase formed at 823, 873, and 923 K indicated an increase in tetragonality of the phase with increasing nickel content.

  8. Room temperature isotherms for Mo and Ni

    International Nuclear Information System (INIS)

    Isotherms at room temperature for Mo and Ni are proposed. They are of three types: BIRCH, KEANE and BORN-MIE. The adjustable constants appearing in these isotherms have been determined from experimental quantities at zero pressure. An evaluation of the limit of (δBT/δP)T as P #-> # ∞, where BT is the isothermal bulk modulus, has been also used. These three isotherms obtained for Mo and Ni are compared with isotherms derived from shock-wave data according to the PRIETO's model. There is a good agreement between these and these derived from shock-wave data. The three isotherms proposed for Mo and Ni can be considered as valid until pressures of several BTo, where BTo is the bulk modulus BT at P = o

  9. Voz del niño

    OpenAIRE

    Urra-Barandiarán, A. (Ainhoa); Vázquez-de-la-Iglesia, F. (Francisco); Fernandez-Gonzalez, S. (Secundino); Molina, M.T. (M.T.)

    2006-01-01

    En el curso de la vida la voz sufre diferentes cambios que obedecen a factores de desarrollo y en los que intervienen de manera decisiva el sistema nervioso y el sistema hormonal. La voz del niño y, por tanto la disfonía en el niño requiere una evaluación precisa y específica, no sólo desde el punto de vista instrumental sino también perceptual y en evaluación logopédica. Se insiste en la protocolización de elaboración de trastornos de voz en el niño, la revisión de los f...

  10. Kinetics of Ni3Si2 Formation in the Ni2Si-NiSi Thin Film Reaction from in situ Measurements

    Energy Technology Data Exchange (ETDEWEB)

    Kittl,J.; Pawlak, M.; Torregiani, C.; Lauwers, A.; Demeurisse, C.; Vrancken, C.; Absil, P.; Biesemens, S.; Detavernier, C.; et al

    2007-01-01

    The kinetics of Ni3Si2 formation in the Ni2Si-NiSi thin film reaction were determined from simultaneous in situ x-ray diffraction (XRD) measurements, performed using a synchrotron source, and sheet resistance measurements. Samples consisted of 90 nm Ni/100 nm polycrystalline-Si/SiO2 stacks, of interest for fully silicided gate applications, on (100) Si. After initial formation of a Ni2Si/NiSi bilayer, these films reacted to form Ni3Si2. The evolution of sheet resistance and of the intensity of XRD peaks were used to extract the fraction of Ni3Si2 formed during ramp and isothermal annealings. A Kissinger analysis was performed for ramp annealing with ramp rates of 1, 3, 5, 9, and 27 C/s, obtaining the activation energy of Ni3Si2 formation, Ea = 1.92{+-}0.15 eV. A Kolmogorov-Johnson-Mehl-Avrami analysis was performed for isothermal anneals, finding an Avrami exponent of 2.1{+-}0.2, suggesting two-dimensional growth. This is consistent with a nucleation controlled process for Ni3Si2 formation, with nucleation sites at different positions in the thin film, and subsequent lateral two-dimensional propagation of the transformation front parallel to the film surface. Implications for Ni fully silicided gate applications are discussed.

  11. Fully gapped superconductivity in Ni-pnictide superconductors BaNi2As2 and SrNi2P2

    International Nuclear Information System (INIS)

    We have performed low-temperature specific heat C and thermal conductivity κ measurements on the Ni-pnictide superconductors BaNi2As2 (Tc = 0.7K) and SrNi2P2 (Tc = 1.4K). The temperature dependences C(T) and κ(T) of the two compounds are similar to the results of a number of s-wave superconductors. Furthermore, the concave field responses of the residual κ for BaNi2As2 rules out the presence of nodes on the Fermi surfaces. We postulate that fully gapped superconductivity could be universal for Ni-pnictide superconductors. Specific heat data on Ba0.6La0.4Ni2As2 shows a mild suppression of Tc and Hc2 relative to BaNi2As2.

  12. Application of Nanocrystalline LaNi5-type Hydrogen Absorbing Alloys in Ni-MHx Batteries

    Institute of Scientific and Technical Information of China (English)

    Jurczyk M; Nowak M

    2004-01-01

    The structure and electrochemical properties of nanocrystalline LaNi5-type alloys were studied. These materials were prepared by mechanical alloying (MA) followed by annealing. The properties of hydrogen host materials can be modified substantially by alloying to obtain the desired storage characteristics. It was found that the partial substitution of Ni by Al or Mn in LaNi5-xMx alloy leads to an increase in discharge capacity. The alloying elements such as Al, Mn and Co greatly improved the cycle life of LaNi5 material. For example, in the nanocrystalline LaNi3.75Mn0.75Al0.25Co0.25 powder, discharge capacity up to 258 mAh·g-1 was measured (at 40 mA·g-1 discharge current). Furthermore,the effect of the graphite coating on the structure of some nanocrystalline alloys and the electrodes characteristics were investigated. The mechanical coating with graphite effectively reduced the degradation rate of the studied electrode materials. The combination of a nanocrystalline LaNi5-type hydride electrodes and a nickel positive electrode to form a Ni-MH battery, was successful.

  13. Blending Cr2O3 into a NiO-Ni electrocatalyst for sustained water splitting.

    Science.gov (United States)

    Gong, Ming; Zhou, Wu; Kenney, Michael James; Kapusta, Rich; Cowley, Sam; Wu, Yingpeng; Lu, Bingan; Lin, Meng-Chang; Wang, Di-Yan; Yang, Jiang; Hwang, Bing-Joe; Dai, Hongjie

    2015-10-01

    The rising H2 economy demands active and durable electrocatalysts based on low-cost, earth-abundant materials for water electrolysis/photolysis. Here we report nanoscale Ni metal cores over-coated by a Cr2 O3 -blended NiO layer synthesized on metallic foam substrates. The Ni@NiO/Cr2 O3 triphase material exhibits superior activity and stability similar to Pt for the hydrogen-evolution reaction in basic solutions. The chemically stable Cr2 O3 is crucial for preventing oxidation of the Ni core, maintaining abundant NiO/Ni interfaces as catalytically active sites in the heterostructure and thus imparting high stability to the hydrogen-evolution catalyst. The highly active and stable electrocatalyst enables an alkaline electrolyzer operating at 20 mA cm(-2) at a voltage lower than 1.5 V, lasting longer than 3 weeks without decay. The non-precious metal catalysts afford a high efficiency of about 15 % for light-driven water splitting using GaAs solar cells. PMID:26307213

  14. Corrosion and wear resistance study of Ni-P and Ni-P-PTFE nanocomposite coatings

    Science.gov (United States)

    Ankita, Sharma; Singh, Ajay

    2011-09-01

    This article reports on the corrosion and wear resistance of Ni-P and Ni-P-PTFE nanocomposite coatings deposited on mild steel substrates using the electroless plating technique. The coatings were characterized by scanning electron microscopy (SEM), energy dispersive analysis of X-Ray (EDAX), and X-ray diffractometry (XRD). The coatings were smooth and had thicknesses between 7 and 23 µm. They contained Ni, P, and additionally, F, in the case of the Ni-P-PTFE films. A broadening of the Ni peak in XRD was attributed to the amorphous nature and/or fine grain size of the films. Corrosion resistance was measured using immersion and electrochemical polarization tests in 3.5% NaCl solution whereas wear resistance was determined by the pin-on-disc method. Both Ni-P and Ni-P-PTFE coatings exhibited significant improvement in corrosion (in salty media) and wear behavior. Furthermore, the addition of PTFE in the coatings showed improvement in their corrosion resistance as well as a reduction in friction coefficient. Our testing revealed that the coatings' wore out following the "adhesive type" mechanism.

  15. Radiation-induced segregation in diluted NiSi and NiGe alloys. Bestrahlungsinduzierte Segregation in verduennten NiSi- uns NiGe-Legierungen

    Energy Technology Data Exchange (ETDEWEB)

    Weigert, M.

    1987-05-12

    By means of 3 MeV electron radiation the radiation-induced Si or Ge enrichment at point defect sinks of dilute NiSi and NiGe alloys (45-496 atppm) was investigated by the ensueing reduction of the concentration of extra-lattice Si or Ge atoms. The concentration of the detached foreign atoms is analyzed by reciprocal damage rates in the temperature range II. In this process the migrating interstitial atoms which are able to form stable and immobile complexes with the foreign atoms, are used as probes for determining the concentration of detached foreign atoms.

  16. Separation of radiation defects in Ni and Ni-C alloys under electron and neutron irradiation

    Science.gov (United States)

    Arbuzov, S. E.; Danilov, V. L.; Goshchitskii, B. N.; Kar'kin, A. E.; Parkhomenko, V. D.

    2016-02-01

    Complex investigations of radiation damage of Ni and Ni- 880 at. ppm C alloy under electron and neutron irradiation in the region of room temperature hardened and deformed state. In pure nickel, with the deformation microstructure, both in electron and in the neutron irradiation is observed separation of radiation-induced defects. When electron irradiation in the alloy Ni-C separation effect is observed, and when neutron irradiation there is no. This is due to the interaction of carbon atoms with radiation defects. The main sinks for radiation-induced defects are the areas with a high concentration of defects in cascades of atomic displacements.

  17. Synthesis of TiNi/Ti2Ni Composite Particles in Molten Salts

    Institute of Scientific and Technical Information of China (English)

    YANG Rui-song; CUI Li-shan; ZHENG Yan-jun

    2006-01-01

    A new process of synthesizing TiNi/Ti2Ni composite particles, high temperature molten salts method, is introduced. This method uses molten salts as a reaction medium that does not take part in the chemical reaction and can be easily dissolved in rinsing water. According this method, the composite particles were prepared in molten salts at 700 ℃-900 ℃. By means of differential scanning calorimetry (DSC), the reversible martensitic transformation of TiNi particles in these composite particles was confirmed.

  18. Participar como niña o niño en el mundo social

    OpenAIRE

    Silvia Paulina Díaz

    2010-01-01

    En este artículo presento la participación como resultado de un trabajo investigativo realizado durante el año 2007, con niños y niñas escolarizados habitantes de la ciudad de Medellín, Colombia, cuyo objetivo fue analizar las representaciones sociales que ellos y ellas comparten sobre el ejercicio ciudadano. El análisis de la información tiene como ejes fundamentales, la salud colectiva, la sociología de la infancia y la participación en la niñez, en una aproximación que se realiza desde un ...

  19. THICKNESS DEPENDENCE OF MAGNETIZATION AND MAGNETOSTRICTION OF NiFe AND NiFeRh FILMS

    OpenAIRE

    Ounadjela, K.; Lefakis, H.; Speriosu, V.; Hwang, C.; Alexopoulos, P.

    1988-01-01

    The saturation magnetization, 4πMs, and the magnetostriction constant, λ, of Ni81Fe19, Ni81Fe19/Ta and Ni72Fe17Rh11/ Ta thinfilms were studied as a function of film thickness before and after annealing. For films of thickness t < 200 Å, 4πMs, and λs were found to be strongly dependent on film thickness with even larger variation after annealing. Auger depth profiles have shown the existence of inhomogeneous interfacial layer at the film surface, Ta/film and film/substrate interfaces. The pres...

  20. Structure characterization of Ni/NiO and Ti/TiO2 interfaces

    International Nuclear Information System (INIS)

    This research thesis reports the structure characterization of Ni-NiO and Ti-TiO2 interfaces through an in-situ investigation of thin blade oxidation, of oxide germination and growth, and through a determination of mutual metal/oxide orientation relationships. Thin films of TiO2 have also been characterized and the study of the influence of vacuum annealing on TiO2 layer structure and morphology has been attempted. The examination of metal-oxide interface reveals a duplex structure of NiO and TiO2 layers, and a preferential grain boundary oxidation of the underlying metal

  1. Air oxidation of Cu-50Ni and Cu-70Ni alloys at 800℃

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The air oxidation of Cu-Ni alloys with 50% and 70% nickel (mole fraction) at 800℃ was studied. The kinetic curves for the oxidation of the two alloys are complex and deviate from the parabolic rate law. Typical double-layered scales are produced, which consist of a CuO outer layer and an inner layer containing a mixture of Cu2O and NiO with many pores. Cu-50Ni presents a small degree of internal oxidation of nickel, which is observed in many binary double-phase systems, but is quite rare in single phase systems.

  2. Microstructure of Ni-Al powder and Ni-Al composite coatings prepared by twin-wire arc spraying

    Institute of Scientific and Technical Information of China (English)

    Ji-xiao Wang; Gui-xian Wang; Jing-shun Liu; Lun-yong Zhang; Wei Wang; Ze Li; Qi-xiang Wang; Jian-fei Sun

    2016-01-01

    Ni–Al powder and Ni–Al composite coatings were fabricated by twin-wire arc spraying (TWAS). The microstructures of Ni-5wt%Al powder and Ni-20wt%Al powder were characterized by scanning electronic microscopy (SEM) and energy dispersive spec-troscopy (EDS). The results showed that the obtained particle size ranged from 5 to 50μm. The morphology of the Ni–Al powder showed that molten particles were composed of Ni solid solution, NiAl, Ni3Al, Al2O3, and NiO. The Ni–Al phase and a small amount of Al2O3 parti-cles changed the composition of the coating. The microstructures of the twin-wire-arc-sprayed Ni–Al composite coatings were characterized by SEM, EDS, X-ray diffraction (XRD), and transmission electron microscopy (TEM). The results showed that the main phase of the Ni-5wt%Al coating consisted of Ni solid solution and NiAl in addition to a small amount of Al2O3. The main phase of the Ni-20wt%Al coating mainly consisted of Ni solid solution, NiAl, and Ni3Al in addition to a small amount of Al and Al2O3, and NiAl and Ni3Al intermet-allic compounds effectively further improved the final wear property of the coatings. TEM analysis indicated that fine spherical NiAl3 pre-cipitates and a Ni–Al–O amorphous phase formed in the matrix of the Ni solid solution in the original state.

  3. Nanomechanical properties of a Ni nanodot-patterned surface

    International Nuclear Information System (INIS)

    Nanomechanical properties of a Ni nanodot-patterned surface (NDPS) on a Si substrate were investigated using nanoindentation. The Ni NDPS was fabricated by thermal evaporation of Ni through a porous anodized aluminum oxide template onto a Si substrate. Plan-view transmission electron microscopy and nanobeam diffraction were used to characterize the Ni nanodot crystal structure. Scanning electron microscopy and atomic force microscopy were used to characterize the morphology and deformation of the Ni nanodots before and after nanoindentation. The elastic modulus and hardness of the Ni nanodots were found to be 159 ± 22 and 7.7 ± 1.0 GPa, respectively. The critical shear stress for initiating plastic deformation in the Ni nanodot was estimated to be 8.3 ± 1.0 GPa, which is close to the theoretical shear strength of 7.6 GPa in dislocation-free single crystal Ni

  4. Electrochemical performance study of Ni/Ni-GDC double-layer anode-supported IT-SOFC%Ni/Ni-GDC双层阳极支撑型IT-SOFC性能研究

    Institute of Scientific and Technical Information of China (English)

    郭桂平; 彭开萍

    2015-01-01

    采用硝酸盐-柠檬酸溶胶-凝胶低温自蔓延燃烧法制备GDC粉末,用共压法制备了NiO-GDC单层阳极、NiO/NiO-GDC双层阳极及其单电池,并测试了其性能。研究结果表明:经H2还原后,Ni/Ni-GDC双层阳极外层为多孔结构,由粒径较大的Ni粒子团形成了稳定的电子电导通道及燃料通道;内层孔隙较小、较少,Ni均匀分布于GDC构成的支撑骨架中。Ni/Ni-GDC双层阳极的孔隙率及电导率都高于Ni-GDC单层阳极,从450~700℃,其电导率比Ni-GDC单层阳极都稳定高出15%~20%。单电池的测试结果表明:Ni/Ni-GDC双层阳极支撑单电池在700、650、600℃的最大功率密度分别为0.383、0.329、0.204 W/cm2,比Ni-GDC单层阳极支撑单电池分别高出了8.95%、79.38%、84.76%。Ni/Ni-GDC双层阳极支撑单电池具有比Ni-GDC单层阳极支撑单电池更高的中温、特别是低温电化学性能。%GDC electrolyte powder was synthesized by nitrate-citric acid sol-gel auto combustion method in low temperature. NiO-GDC single-layer anode, NiO/NiO-GDC double-layer anode and their single cells were prepared by co-pressing, then their properties were tested. The test results show that after reduction by H2, the outer layer of the Ni/Ni-GDC double-layer anode is porous and stable electronic conductivity channel and fuel channel is formed by the Ni particle groups with large size. In the inner layer, pores are less and smal er, and Ni particles distribute uniformly in the skeleton structure formed by GDC particle. Both the porosity and conductivity of Ni/Ni-GDC double-layer anode are higher than Ni-GDC single-layer anode; its conductivities from 450 to 700℃are al 15%~20%higher than Ni-GDC single-layer anode. The single celltest shows that the peak power densities of Ni/Ni-GDC double-layer anode-supported single cellat temperature 700, 650 and 600℃are respectively 0.383, 0.329 and 0.204 W/cm2, which are respectively 8.95%, 79.38%, 84

  5. Fabrication of CdTe/NiTe films on Ni foils by radio-frequency magnetron sputtering method

    International Nuclear Information System (INIS)

    Highlights: • The effects of Ts on CdTe deposited on Ni by magnetron sputtering is investigated. • An effective method is studied of making CdTe/NiTe without post-treatment. • As-prepared CdTe/NiTe raised optical absorption and PEC properties. • Pre-deposited Te can react with Ni to generate NiTe at Ts = 350 °C. - Abstract: Cadmium Telluride (CdTe) semiconductor thin films are fabricated on flexible Ni foil substrates using radio-frequency (RF) magnetron sputtering under different substrate temperatures. The crystal structure and properties of the prepared functional thin films were characterized with series analysis technologies. The characterization results revealed that Nickel Telluride (NiTe) phase formatted at the interface of CdTe and Ni substrate when substrate temperature (Ts) is 450 °C. Specially, XRD results demonstrated that CdTe/NiTe films could also be obtained by pre-depositing Te film on Ni and reducing Ts to 350 °C. The investigation on optical and photoelectrochemical (PEC) properties of the products illustrated that compact CdTe/NiTe films had improved the absorption in the visible region. Furthermore, PEC measurements indicated that CdTe/NiTe/Ni photoelectrode can have a promising application in photovoltaic devices

  6. Hydrogenation of Ethyl Acetate to Ethanol over Ni-Based Catalysts Obtained from Ni/Al Hydrotalcite-Like Compounds

    Directory of Open Access Journals (Sweden)

    Longfei Jiang

    2010-07-01

    Full Text Available A series of Ni-based catalysts were prepared using hydrogen reduction of Ni/Al hydrotalcite-like compounds (Ni/Al HTlcs synthesized by coprecipitation. The physico-chemical properties of Ni/Al hydrotalcite-like compounds and the corresponding Ni-based catalysts were characterized using inductively coupled plasma (ICP, BET surface areas, X-ray diffraction (XRD, Fourier transform infrared (FTIR spectroscopy and scanning electron microscopy (SEM techniques. The results indicated that Ni/Al HTlcs with layered structures could be successfully prepared by the coprecipitation method, and the characteristic HTlcs reflections were also observed in the XRD analysis. The NiO and Ni0 phases were identified in all Ni-based catalysts, which displayed randomly interconnected pores and no layer structures. In addition, the studies also found the Ni/Al HTlcs and Ni-based catalysts had high specific surface areas, low pore volumes and low pore diameters. The catalytic hydrogenation of ethyl acetate to ethanol with Ni-based catalysts was also investigated. Among the studied catalysts, RE1NASH-110-3 showed the highest selectivity and yield of ethyl acetate to ethanol, which were 68.2% and 61.7%, respectively. At the same time, a major by-product, butyl acetate, was formed due to an ester-exchange reaction. A proposed hydrogenation pathway for ethyl acetate over Ni-based catalysts was suggested.

  7. The study of quasi-projectiles produced in Ni+Ni and Ni+Au collisions: excitation energy and spin

    International Nuclear Information System (INIS)

    During the collision between the projectile and the target nuclei in the intermediate energy regime (E < 100 MeV/nucleon) two excited nuclei are mainly observed in the exit channel, the quasi projectile (QP) and the quasi target. They disintegrate by particle emission. However, this binary picture is perturbed by the emission of particles and light fragments with velocities intermediate between the projectile velocity and the target one, all along the interaction (midrapidity component). This work aim to determine the excitation energy and the intrinsic angular momentum (or spin) of quasi-projectiles produced in the Ni+Ni and Ni+Au collisions at 52 and 90 MeV/nucleon. The excitation energy is deduced from the kinematical characteristics of particles emitted by the quasi-projectile. They have to be separated from midrapidity particles. Three different scenarios have been used for this purpose. The spin of the quasi-projectile has been extracted from the experimental data by mean of proton and alpha particles multiplicities emitted by the QP in the Ni+Au at 52 MeV/nucleon reaction. The results have been compared to the predictions of a theoretical model based on nucleon transfers. Their evolution is qualitatively reproduced as a function of the violence of the collision. (author)

  8. Application of 61Ni Moessbauer spectroscopy to chemical problems

    International Nuclear Information System (INIS)

    Using the possibility to produce 61Co sources at the MAinz Microtron, 61Ni Moessbauer spectroscopy was applied to different kinds of chemical problems. Measurements of isomer shifts and Vzz values in some common compounds and compounds with unusual chemical bonding for comparison with band structure calculations, measurement of 61Ni Moessbauer parameters in model compounds for hydrogenase and dehydrogenase with an active [NiS4] centre, and study of novel binary NiF3 compounds at helium temperature are presented

  9. Mixed conductor anodes: Ni as electrocatalyst for hydrogen conversion

    DEFF Research Database (Denmark)

    Primdahl, S.; Mogensen, Mogens Bjerg

    2002-01-01

    Five types of anodes for solid oxide fuel cells (SOFC) are examined on an yttria-stabilised zirconia (YSZ) electrolyte by impedance spectroscopy at 850 degreesC in hydrogen. The examined porous anodes are a Ni/Zr(0.92)Y(0.16)O(2.08) (Ni/YSZ) cermet, a Ni/Ce(0.9)Gd(0.1)O(1.95) (Ni/CGI) cermet, a Ce...

  10. Kinetics of NiO and NiCl2 hydrogen reduction as precursors and properties of produced Ni/Al2O3 and Ni-Pd/Al2O3 catalysts.

    Science.gov (United States)

    Sokić, Miroslav; Kamberović, Željko; Nikolić, Vesna; Marković, Branislav; Korać, Marija; Anđić, Zoran; Gavrilovski, Milorad

    2015-01-01

    The objects of this investigation were the comparative kinetic analysis of the NiO and NiCl2 reduction by hydrogen during an induction period and elimination of the calcination during the synthesis of Ni/Al2O3 catalysts. The effect of temperature and time on NiO and NiCl2 reduction degrees was studied. Avrami I equation was selected as the most favorable kinetic model and used to determine activation energy of the NiO and NiCl2 reduction for the investigated temperature range (623-923 K) and time intervals (1-5 minutes). The investigation enabled reaching conclusions about the reaction ability and rate of the reduction processes. Afterward, Ni/Al2O3 catalysts were obtained by using oxide and chloride precursor for Ni. The catalysts were supported on alumina-based foam and prepared via aerosol route. Properties of the samples before and after low-temperature hydrogen reduction (633 K) were compared. Obtained results indicated that the synthesis of Ni/Al2O3 catalysts can be more efficient if chloride precursor for Ni is directly reduced by hydrogen during the synthesis process, without the calcination step. In addition, Ni-Pd/Al2O3 catalysts with different metal content were prepared by using chloride precursors. Lower reduction temperature was utilized and the chlorides were almost completely reduced at 533 K. PMID:25789335

  11. Initial growth of Au on Ni(110): Surface alloying of immiscible metals

    DEFF Research Database (Denmark)

    Nielsen, L. Pleth; Besenbacher, Flemming; Stensgaard, I.;

    1993-01-01

    Atomic resolution scanning tunneling microscopy of Au deposited on Ni(110) shows that even though Au is completely insoluble in bulk Ni, it replaces Ni in the first surface layer forming a surface Au-Ni alloy and the squeezed out Ni atoms agglomerate in Ni islands on the surface. This picture is...

  12. The evolution of phase transformation in Ni/Ni3Al laminated composite under high temperature treatments

    Science.gov (United States)

    Shmorgun, V.; Gurevich, L.; Bogdanov, A.; Trunov, M.

    2016-02-01

    In this study the impact of isothermal annealing on the phase transformation rate in laminated Ni/Ni2Al3 composite was investigated. The method of nickel-aluminide coatings of the required chemical composition fabrication was proposed.

  13. Gel-combustion synthesis of NiO-MoO3 mixtures and their reduction to Ni-Mo alloys

    International Nuclear Information System (INIS)

    The oxide mixtures xNiO-(1 - x)MoO3 (0.2 ≤ x ≤ 1) were synthesized by gel-combustion procedure, using mixed aqueous solutions of ammonium molybdate, nickel nitrate and citric acid as the precursor solution. The oxide products were characterized by scanning electron microscopy and X-ray diffractometry. The X-ray diffractograms indicated the presence of NiMoO4 and either NiO or MoO3 in the oxide products. By heating in hydrogen atmosphere, the oxide mixtures were transformed into Ni-Mo alloys. Thermogravimetric study of the reduction procedure evidenced that temperature indispensable to complete reduction increased progressively from 400 to 900 deg. C if x decreased from 1 toward 0. The structure of Ni-Mo alloys was examined by X-ray diffractometry, and the following alloys were evidenced: Ni(Mo) solid solutions, Ni4Mo, and NiMo

  14. Controlled synthesis of Ni/CuOx/Ni nanowires by electrochemical deposition with self-compliance bipolar resistive switching

    OpenAIRE

    Kyuhyun Park; Jang-Sik Lee

    2016-01-01

    We demonstrate synthesis of Ni/CuOx/Ni nanowires (NWs) by electrochemical deposition on anodized aluminum oxide (AAO) membranes. AAO with pore diameter of ~70 nm and pore length of ~50 μm was used as the template for synthesis of NWs. After deposition of Au as the seed layer, NWs with a structure of Ni/CuOx/Ni were grown with a length of ~12 μm. The lengths of 1st Ni, CuOx, and 2nd Ni were ~4.5 μm, ~3 μm, and ~4.5 μm, respectively. The Ni/CuOx/Ni device exhibits bipolar resistive switching be...

  15. On the new supply houses per thousand heads during this five in Japan. At 47 prefectures and 80 cities; 300,000 and more population on 1995; Saikin 5 nenkan ni okeru riyo kankeibetsu jutaku chakodo suii. 47 todofuken and 80 toshi (jinko 300,000 nin 'heisei 7 {center_dot} kokucho' ijo narabini kencho shozaishi)(1993 {approx} 1997)

    Energy Technology Data Exchange (ETDEWEB)

    Iida, Toshihiko; Kojina, Kyoji

    1999-03-01

    We studied before twice the construction-started houses per thousand heads during five years, 1983 {approx} 1987 and 1988 {approx} 1992 at 47 prefectures and 77 or 81 cities; 300,000 and more population and the cities of prefectural government in Japan. For the third time we study now the construction-started houses in Japan. We call the construction-started houses per thousand heads yearly the construction-started ratio at each areas. The average construction-started ratio was 11.10 houses during five years; 1983 {approx} 1987, so 12.51 houses during five years; 1988 {approx} 1992 and 11.99 houses during five years; 1993 {approx} 1997 in Japan. Then at prefectures the average construction-started ratio houses spreaded from 6.31 houses at Tottori-ken to 15.51 houses at Tokyo-to during 1983 {approx} 1987, so from 6.52 houses at Shimane-ken to 16.66 houses at Kanagawa-ken during five years; 1988 {approx} 1992 and from 8.01 house at Shimane-ken to 16.70 houses at Hyogo-ken during five years; 1993 {approx} 1997 in Japan. The same items of each tenure spreaded among some ranges during this period. Next we study on the four tenures, 1st on the owned tenure. On the owned tenure, the average construction-started ratio was 4.03 houses during 1983 {approx} 1987, so so 3.96 houses during 1988 {approx} 1992 and 4.39 houses during 1993 {approx} 1997 in Japan. 2nd on the rental tenure, the average construction-started ratio was 4.95 houses during 1983 {approx} 1987, so 5.87 houses during 1988 {approx} 1992 and 4.65 houses during 1993 {approx}1997 in Japan. 3rd on the issued tenure, the average construction-started ratio was 0.19 houses during five years; 1983 {approx} 1987, so 0.27 houses during five years; 1988 {approx} 1992 and 0.21 houses during five years; 1993 {approx} 1997 in Japan. 4th on the for-sale tenure, the average construction-started ratio was 1.93 houses during five years; 1983 {approx} 1987, so 2.41 houses during five years; 1988 {approx} 1992, so 2.73 houses during five years; 1993 {approx} 1997 in Japan.There were differences in tendencies of the construction-started houses among four tenures during fifteen years. The average construction-started ratio changed from 4.96 and 5.89 to 4.65 houses in the rental tenure, the same of the for-sale tenure changed from 1.93 and 2.41 to 2.73 houses during this periods. We obtained the following results in this studies that the construction-started houses per thousand heads in the for-sale tenure have been spreaded among range, for example from 3.75 houses or 3.42 houses to 4.37 houses, though the same values in the rental tenure have been changed from 6.66 houses or 8.27 houses to 4.50 houses now. (author)

  16. Applicability of the spatial autocorrection method for estimation of basement structure in Kanto plain. Array measurements of microtremors close to the Iwatsuki and Shimosa deep borehole observatory; Kanto heiya no kiban kozo suitei no tame no kukan jiko sokanho no tekiyosei. Iwatsuki Shimosa jiban katsudo kansokusei ni okeru array bido kansoku

    Energy Technology Data Exchange (ETDEWEB)

    Matsuoka, T.; Umezawa, N.; Shiraishi, H. [Saitama Institute of Environmental Pollution, Saitama (Japan)

    1996-10-01

    To investigate applicability of the spatial autocorrection method which is a microtremors exploration method for the estimation of basement structure, array measurements of microtremors were performed using the Iwatsuki and Shimosa deep borehole observatory where detailed structures were clarified as well as the Fuchu and Koto deep borehole observatory. In this study, estimated velocity structures of S-wave were compared with the geological sequence and results of acoustic velocity logging. The phase velocity was estimated by the spatial autocorrection method using FFT. The phase velocity with a smooth normal dispersion was observed in the periodic range from 0.5 to 5 sec in Iwatsuki, and from 0.5 to 4 sec in Shimosa by the combination of four-point circular arrays with radii of 100, 300, and 600 m. The underground structures estimated from the phase velocities coincided well with the geological sequence, and results of acoustic velocity logging and velocity logging for each borehole. For the Iwatsuki borehole, the basement velocity was also estimated properly in the periodic range of observation. While, for the Shimosa borehole, measurements with the period around 6 sec were required to estimate the basement velocity more accurately. 13 refs., 11 figs., 1 tab.

  17. Mixed lubrication analysis for spherical valve plate in piston rod driving type bent-axial-type axial piston pump. 1st Report. Mathematical model; Rod kudo hoshiki shajikushiki piston pump ni okeru kyumen benban no kongo junkatsu kaiseki. 1. Sugaku model

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, K. [Fukui National College of Technology, Fukui (Japan); Kyogoku, K.; Momozono, S.; Nakahara, T. [Tokyo Institute of Technology, Tokyo (Japan)

    1999-06-25

    In order to investigate lubrication characteristics between rotor and spherical valve plate, a mathematical model of rotor motion has been presented for a piston rod driving type bent-axis-type axial piston pump. The forces and the moments acting on the rotor through the piston rod have been derived from geometric analysis of rotor driving mechanism with the piston rod. An analysis model on mixed lubrication between the rotor and the spherical valve plate has been shown using Average-Flow-Model by Patir-Cheng and the contact theory by Greenwood-Tripp, respectively. In addition, bearing part between the rotor and shaft, supporting element of the rotor, has been regarded as squeeze film bearing. The simulation for the lubrication characteristics, such as minimum film thickness, its occurring position and friction loss between the rotor and the spherical valve plate, will be demonstrated in the paper, part 2. (author)

  18. Mixed lubrication analysis for spherical valve plate in piston rod driving type bent-axial-type axial piston pump. 2nd Report. Numerical calculation results; Rod kudo hoshiki shajikushiki piston pump ni okeru kyumen benban no kongo junkatsu kaiseki. 2. Suchi keisan kekka

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, K. [Fukui National College of Technology, Fukui (Japan); Kyogoku, K.; Momozono, S.; Nakahara, T. [Tokyo Institute of Technology, Tokyo (Japan)

    1999-06-25

    The paper, part 1, has proposed a mathematical model of rotor motion for piston rod driving type bent-axis-type axial piston pump in order to study lubrication characteristics between rotor and spherical valve plate. The numerical calculations have been carried out under operating conditions and specifications. The calculation results have been compared with experimental ones given by previous papers. It is found that (1) the rotor moves to delivery area and its axis tilts to one with its rotation, (2) film thickness between the rotor and the spherical valve plate minimizes at inside sealing part and the center of fluctuation locates near neutral point of the delivery area, and (3) the minimum film thickness and friction moment are greatly influenced by rotational speed, viscosity and dimension of sealing part on the spherical valve plate. (author)

  19. Fiscal 1997 report on the results of the international standardization R and D. Quantification of the sensory evaluation and international standardization in the paint field; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Toryo bun`ya ni okeru kanno hyoka no teiryoka to kokusai hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Japanese paint users demand products of higher-quality than users in the U.S. and Europe, and therefore, paint makeres in Japan are making strenuous efforts to improve the product quality in terms of homogeneity, appearence and durability of the surface of paint films. However, the evaluation of paint surfaces is conducted by the qualitative sensory evaluation, resulting in obtaining no appropriate evaluation. Accordingly, the following were developed as new evaluation methods which give rational and economical indicators, contribute to shortening of the period for development of new products, and aim at the international standardization: 1) quantitative evaluation of the paint drying process; 2) image analysis of the degraded part of paint films; 3) surface analysis of paint films. In 1), a kinetic friction measuring quantitative evaluation of the surface of paint films was developed. In 2), the development of an exclusive program by the image analysis made the quantitative evaluation with high accuracy/reliability possible. In 3), an evaluation method was developed in which differences among the specimens can be detected by the chemiluminescent measurement in an extremely early stage of exposure when the gloss change just begins. As to the chalking, a new evaluation was developed in which the degree of chalking can quantitatively be evaluated by attaching a special adhesion tape to the degraded part of paint films and by the optical measurement of the degree of transparency. 101 refs., 341 figs., 118 tabs.

  20. 18th national meeting for energy saving promotion (prize winning case awarded by Minstry of International Trade and Industry). ; Optimization of additive carrying argon gas in continuous casting. Dai 18 kai sho energy suishin zenkoku taikai (tsusho sangyo daijinsho jusho jirei). ; Renzoku chuzo ni okeru tenkazai hansoyo argon gas no saitekika

    Energy Technology Data Exchange (ETDEWEB)

    1993-01-30

    An optimal amount of argon gas carrying CaSi additive particles was discovered in a continuous casting process and a stable operation method was established to conserve energy and cost. CaSi particles are added into molten steel to prevent steel materials from cracking, and argon gas is used in carrying the CaSi particles to prevent oxygen and nitrogen from mixing into the molten steel. The proposed modification plan intends to use the existing facilities up to the seal rotary machine, and to reduce the size and length of the carrying pipes thereafter, the length of the flexible tubes, and the size of the booster. A verification test was carried out. As a result of measuring the CaSi particle scattering distribution, it was found that an in-pipe flow velocity of 25 m/s produces a narrow scattering distribution and has the particles impinge on the molten steel dropping position concentratedly. It was also learned that the in-pipe flow velocity of 25 m/s can increase the solid-air ratio to 0.81 to 1.21. Operations of the modified machine reduced the argon gas amount by 5.2 m[sup 3]N/min (reduction rate of 61%) and realized stabler CaSi particle injection which improved the Ca yield by 9.4%. 14 figs., 7 tabs.

  1. International seminar in fiscal 1998 on the development and promotion of global environment-related industrial technologies. Report on International Workshops on CO{sub 2} Cycling and Metabolism in Coral Reef; 1998 nendo chikyu sangyo gijutsu kaihatsu suishin jigyo. 'Sangosho ni okeru busshitsu ido to tanso junkan' kokusai workshop hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the study of CO{sub 2} absorption and fixation in the marine ecosystem, studies of coral reefs by RITE (Research Institute of Innovative Technology for the Earth) were subjected to discussion at the above-named workshops. It is after the elapse of a long geological time on the earth that CO2 in the atmosphere has arrived at the current level of concentration thanks to fixation and calcification by living organisms and to dissolution into the seawater. In the formation of CaCO{sub 3} that constitutes the coral skeleton, 1 mol Ca combines with 2 mol bicarbonates for the production of 1 mol CaCO{sub 3} and 1 mol CO{sub 2}. The reaction may suggests a consequential increase of CO2 in the atmosphere but such CO{sub 2} is in reality consumed by being converted into organic substances in a photosynthetic process performed by symbiotic algae. Calculation was made for the whole of Bora Bay, Miyakojima Island, and the result was that 700kg-C/day comes to be stored in the form of organic matters in the community of coral reef organisms. In a coral reef, even when it emits CO2 into the atmosphere, there is organic matter production which exceeds the lost CO{sub 2}. Coral reefs fix carbon out of the seawater at the rate of 0.42Gt-C/year, which is the aggregate of 0.3Gt organic matters and 0.12Gt CaCO{sub 3}. (NEDO)

  2. Research report of FY 1997 on the environmentally acceptable coal utilization system feasibility survey. Clean coal technology model project seminar held in Thailand; 1997 nendo seika hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Tai ni okeru clean coal technology model jigyo seminar no kaisai)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-02-01

    To reduce SOx with coal utilization, the desulfurization seminar diffusing the demonstration project of simplified desulfurizer introduction was held at the site in Thailand. The purpose is to reduce the environmental pollutants and contribute to the effective utilization of energy with coal utilization in Thailand. Invitation letters were sent to users of coal and heavy oil boilers through the Department of Factories, Ministry of Industry, Thailand, to call participation in the seminar. Inspection of the desulfurizer introduced in the factory of Thai Union Paper Public was included in the seminar for diffusing the project. The inspection site is in the demonstration project site of simplified desulfurizer introduction. There were a lot of participants from Thai users and from Japan. The seminar included the presentations from NEDO, JETRO, FTI, and MOSTE, introduction of general technology for processes of ENAA desulfurizer, introduction of demonstration unit plan by IHI, and introduction of operation of demonstration unit by TUP. 31 figs., 6 tabs.

  3. 3D electrical method and step continuous wave radar method for Nojima site. Results of measurement of resistivity at trench site; Nojima danso ni okeru sanjigenhi teikoho to step shiki renzokuha chika radar ho tansa. Trench chosa chiten deno hiteiko sokutei kekka

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, K.; Oda, Y.; Tank, K. [Central Research Institute of Electric Power Industry, Tokyo (Japan); Hayashi, H. [Kawasaki Geological Engineering Co. Ltd., Tokyo (Japan); Jomori, A. [Japan Crust Research, Tokyo (Japan)

    1996-05-01

    Several surveys were carried out near the Nojima fault, including three-dimensional resistivity measurement and underground radar survey at the Ogura area, underground radar survey at the Hirabayashi area, and resistivity measurement in the vicinity of the trench at the Nashinomoto area, in order to investigate in detail the underground structures at a depth up to several tens meters from the ground surface. Resistivity was measured by an automatic analyzer capable of simultaneously measuring potential levels at 14 channels which can cover 112 measuring points at the largest. At the Ogura area, the boundary planes of the resistivity structures are continuously detected in the direction of the fault moving during the earthquake period. The underground radar measurement results suggest accumulated displacement of strata at a depth of around 25m in the Osaka Strata and flexible structures. At the Hirabayashi area, the underground radar analysis detects discrete sections in the reflection planes at the fault position, but no reflection planes of high continuity. At the Nashinomoto area, the clay stratum detected in the fault by excavating the trenches are found to be low in resistivity by the resistivity measurement. 4 refs., 11 figs., 2 tabs.

  4. FY 2000 report on the basic survey to promote Joint Implementation, etc. Environmental improvement and energy conservation measures in Pakistan Steel, a state-run enterprise in Pakistan; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Pakistan koku kokuei Pakistan Steel ni okeru kankyo kaizen sho energy taisaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the state-run plant of Pakistan Steel in Pakistan, an investigational study was conducted on energy conservation and reduction in greenhouse effect gas emission. In the project, energy conservation technology on the following was tried to be introduced: coke oven coal moisture control (CMC) equipment, sintering cooler waste heat recovery equipment, blast furnace hot stove waste heat recovery equipment, blast furnace pulverized coal injection (PCI) equipment, blast furnace top pressure recovery turbine (TRT) equipment, and hot strip mill heating furnace regenerative type burner equipment. Further, in the project on environmental improvement, studies were made on coke oven environmental improvement and blast furnace cast house dust collection. The results of the study indicated that economical effects of the energy conservation project were considered as low because the unit price of energy of Pakistan Steel is low. However, substitution of the low-priced domestic coal for the imported coal has a good effect, and energy conservation in the TRT power generation and by the regenerative type burner produces a highly economical effect. Therefore, Pakistan Steel also agrees to positively promote the project. Moreover, concerning the environmental improvement project, it was considered that the necessity of the project is high in the relation of the coke oven aimed at reducing emissions of toxic substances. (NEDO)

  5. Sintering behavior of flying slag particles in entrained-bed coal gasifiers. 3rd Report. Effect of soot on sintering behavior of flying slag particles; Kiryuso sekitan gas ka ro ni okeru hisan slag fun no shoketsu tokusei. 3. Char chu tansobun no slag shoketsu yokusei sayo

    Energy Technology Data Exchange (ETDEWEB)

    Ueda, A.; Kida, E. [Babcock Hitachi K.K., Tokyo (Japan)

    1997-05-25

    The effect of char addition on sintering behavior of flying slag particles in an entrained-bed coal gasifier was examined using four kinds of amorphous water-quenched slag obtained at the pilot plant of HYCOL. This plant was designed to gasify 50 tons of coal per day. The sintering temperatures of the four slags without char were all approximately 800{degree}C. However, Taiheiyo coal slag did not sinter at 900{degree}C when the char added. It was considered that the char collected by the cyclon was a mixture of soot and unburned coal particles and the soot prevented the slag from sintering. Therefore, the effect of soot on sintering behavior was clarified using carbon black as soot. SEM and EDX analyses showed that very small soot particles acted as a dispersant in the slag. 12 refs., 13 figs., 2 tabs.

  6. Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Feasibility study of the environmentally friendly type coal utilization system in Malaysia and Vietnam; Kankyo chowagata sekitan riyo system kanosei chosa. Malaysia Vietnam ni okeru kankyo chowagata sekitan riyo system kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This survey arranged the status of coal utilization technology and the status of coal production, supply, etc. in Malaysia and Vietnam, examined/studied coal utilization systems in both countries, and finally assessed feasibility of introducing the environmentally friendly type coal utilization system. As a country of primary energy source which is abundant in crude oil, natural gas, hydroelectric power, coal, etc., Malaysia now depends on crude oil and natural gas for 80% of its energy, and places emphasis on exploration of natural gas and oil refining. In electric power and cement industries where coal is consumed, effectiveness and environmental issues in association with coal utilization are future subjects. In Vietnam, the north is abundant in hydroelectric power and anthracite, and the south in oil and gas resource, but the north and central districts are in a state of undevelopment. Coal is used for coal thermal power generation, cement industry, and residential/commercial fuel. In the future, effective coal utilization and environmental issues will be subjects. 16 refs., 38 figs., 75 tabs.

  7. Fiscal 1997 feasibility survey of an environment friendly type coal utilization system. Feasibility survey of the environment friendly type coal utilization system in Malaysia and Vietnam (case of Vietnam); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Malaysia oyobi Vietnam ni okeru kankyo chowagata sekitan riyo system kanosei chosa (Vietnam ban))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper grasped the state of coal utilization by coal consumption field, the state of coal physical flow in Vietnam, etc., surveyed/studied a possibility of introducing the environment friendly type coal utilization system, and assessed the possibility. As to energy resources, the north is abundant in hydroelectric and coal (mainly anthracite) resources, and the south in oil and natural gas resources. Coal production in fiscal 1997 is planned to be 10 million tons. Coal preparation technique presently available is only grain size sieving. Accordingly, it is necessary to study for heightening efficiency of facilities and modernizing facilities in accordance with the introduction of the environment friendly type coal utilization technology. During the study, it is possible to propose improvement on coal processing technology (coal preparation technology). Assessment and study are made especially of the coal selection system, fine coal recovery system and waste water treatment system. For the plan on new coal-fired power plants (300MWtimes4), there is left much necessity of proposing studying models considered of the anthracite combustion technology and environmental improvement and of assessing/studying them. 60 figs., 117 tabs.

  8. Development of hydroponic system using agriculture waste. 1. Characteristics of rice husk charcoal as growth medium and vegetable growth; Suiko saibai ni okeru haikibutsu riyo gijutsu no kaihatsu. 1. Momigara kutan no baichi to shite no tokucho to yasai no seiiku

    Energy Technology Data Exchange (ETDEWEB)

    Terazoe, H.; Nakaya, K.; Okano, T. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1994-06-01

    Experimental researches were made on rice husk charcoals processed to be used as culture media for hydroponics. Rice husk charcoals with a size of 1 mm or larger retaining the original shape of the rice husk, and with a size of smaller than 1 mm were made for use in the experiment. In the culture media made of these rice husk charcoals, the charcoal with a particle size greater than 1 mm had more air portion than water portion at 6 cm above the water level, and the charcoal with a particle size smaller than 1 mm had poor air permeability. According to the result of immersing the rice husk charcoal in a culture solution, phosphoric acid ion and manganese in the solution decreased by about 35% and calcium by about 10% in the duration of 120 minutes, as a result of having been adsorbed into the rice husk charcoal. On the other hand, chloride ion increased by about 80% and potassium and iron by about 30%, because of having been dissolved out from the charcoal. In cultivating spinach, butterhead lettuce and radish in the rice husk charcoal culture media, the culture medium with charcoal smaller than 1 mm resulted in harvest reduced by about 75% in spinach, and about 10% in butterhead lettuce. 15 refs., 13 figs., 11 tabs.

  9. Changing process from {zeta}{center_dot}Fe-Zn phase to Al-Fe intermetallic compounds in molten Zn-5mass%Al alloy bath; Yoyu Zn-5mass%Al gokin`yoku ni okeru {zeta}{center_dot}Fe-Zn so no Al-Fe kinzokukan kagobutsu eno henka katei

    Energy Technology Data Exchange (ETDEWEB)

    Uchida, Y.; Ando, A.; Komatsu, A. [Nisshin Steel Co. Ltd., Tokyo (Japan); Yamakawa, K. [University of Osaka Prefecture, Osaka (Japan). College of Engineering

    1998-09-01

    Sheet steels plated with molten Zn-5 mass % Al alloy are used widely to improve rust preventing strength. The purpose of adding aluminum into a plating bath is to form a thin Al-Fe intermetallic compound layer preferentially on a sheet steel to suppress growth of Fe-Zn intermetallic compounds. A sheet steel on which {zeta} Fe-Zn has been formed was immersed in a Zn-5 mass % Al alloy bath to discuss fundamentally its changing behavior. A change has occurred into particulate products composed mainly of Al5Fe2 with Zn dissolved solidly and a molten liquid phase (with lower aluminum concentration than in the bath composition) at a noticeable speed at which 25 to 30 {mu} m disappears in an immersion time of one second. The change from the {zeta} phase into Al5Fe2 first produces an amorphous phase of the Al-Fe-Zn ternary system having higher aluminum concentration than in the bath composition along the {zeta} phase grain boundary. The change is followed by production and growth of nucleus of crystalline Al5Fe2 within the amorphous phase. The production of the particulate products is thought as a result of Zn discharged into the surrounding in association with growth of Al5Fe2 having been concentrated, remolten, and dissociated. Aluminum is supplied by diffusion of liquid aluminum. 10 refs., 5 figs., 1 tab.

  10. Fiscal 1997 survey report. Feasibility study of the environmentally friendly type coal utilization system (feasibility study of the environmentally friendly type coal utilization system in India); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Indo ni okeru kankyo chowagata sekitan riyo system kanosei chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The survey was conducted of the present situation of coal utilization and the present coal situation such as the environmental state of India which is a coal producing/consuming country next to China in Asia. The paper studied a feasibility of the introduction of the environmental friendly type coal utilization system` to be planned in India. The items for survey are the present situation of economy and energy and the future trend, environmental problems on coal utilization, the present status of the coal distribution system and study subjects, the present status of coal utilization by field and study subjects, a possibility of briquette use, a possibility of coal fluidization, electric power development plans and coal combustion technology in each industry, etc. The subjects are the obligation of coal preparation to coal thermal power plants 1000 km away from coal mines starting 2001, measures taken for effective ash use, measures taken for superannuated gas furnaces, etc. Based on the results of these site surveys and reports of the investigation under consignment from CMPDI, the paper studied/analyzed possibilities of introducing the coal utilization system having actual introduction results in Japan to India, and made an investigational report. 39 refs., 12 figs., 56 tabs.

  11. Evaluation of sand-drain method in submarine ground. In-site tests in excavated vertical shaft and study of drain consolidation mechanism; Kaitei jiban ni okeru sand drain jiban kairyo koka no hyoka. Gen`ichi kussaku chosa to kairyo mechanism no kensho

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, S.; Toriihara, M.; Hirama, K. [Obayashi Corp., Tokyo (Japan)

    1999-07-10

    Although many soil stability works using sand-drain methods have been carried out, in-site tests after soil stabilization were rarely done. We conducted in-site tests in a excavated vertical shaft to estimate the effect of sand-drain consolidation at Osaka Maishima Island that was improved about 20 years ago. The tests showed that near the sand-drain water content was lower, strength and consolidation yield stress were bigger than far away from the sand-drain. To estimate these characteristics, we conducted model tests and FEM simulations, and clarified the drain consolidation mechanism. (author)

  12. Effect of weak DC magnetic fields on the AC magnetization of a melt-processed YBa2Cu3Oy; Yoyu YBa{sub 2}Cu{sub 3}Oy no koryu jika oto ni okeru bijaku chokuryu jiba inka koka

    Energy Technology Data Exchange (ETDEWEB)

    Harashima, K.; Tochihara, S.; Yasuoka, H.; Mazaki, H. [National Defence Academy, Yokosuka, Kanagawa (Japan); Inoue, A.; Kakihana, M. [Tokyo Inst. of Tech. (Japan)

    1998-07-01

    Generally, on the study of AC magnetization, the effect of weak DC magnetic field (Hdc) due to earth magnetism or near around current is neglected and this is the state of things. In this study, as one of trials to confirm the appropriateness of the effect by means of model calculation, Yba{sub 2}Cu{sub 3}Oy sample was prepared by a melt-processed method and the temperature dependency of higher harmonic complex susceptibility (Xn) which was a sensitive physical quantity to the nonlinearity of magnetization, was measured. These results were compared with measured results. Authors studied both theoretically and experimentally, the AC magnetic response of type-II superconductors superimposed on a weak Hdc field. Theoretical simulations were made within the construct of the Kim-Anderson critical-state model, where the critical current density Jc is assumed to be given by Jc=k/(Bo+[Bi]). Authors also measured complex susceptibilities (Xn) of a melt-processed Yba{sub 2}Cu{sub 3}Oy specimen and analyzed the observed Xn by applying the magnetization equations derived from the Kim-Anderson model. It was found that the experimental results were qualitatively well reproduced. 12 refs., 7 figs.

  13. Geological information obtained from rock magnetism and magnetic anomaly. Rock magnetism measurement and geomagnetic anomaly analysis in the forearc shelf of Northeast Japan; Ganseki jiki to jiki ijo kara erareru chishitsu joho. Tohoku Nippon zenko rikudana ni okeru ganseki jiki sokutei to chijiki ijo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Nagasaki, Y. [Japan National Oil Corp., Tokyo (Japan)

    1997-12-01

    Improved accuracy and efficiency of magnetism analysis has advanced magnetic exploitation from a mere tool for exploitation of iron ore deposits to a general tool for analyzing geological structures. Magnetism in a bed rock and presence of a rock of high magnetism penetrating a bed rock cause magnetic anomaly, and it is possible to grasp morphology of a sedimentary basin by analyzing its magnetic anomaly observed, for exploitation of oil and natural gas. Magnitude of anomaly must be handled as vector sum of induction and residual magnetization. However, it is sometimes erroneously explained by use of a model which neglects the effect of residual magnetization. This paper reviews the basic aspects of anomaly analysis, and describes an example in which seismic exploitation based on the reflection method, gravity anomaly and magnetism anomaly are considered to explain geological structures, taking, as a case study, geomagnetism anomaly observed off Sanriku. The rock-magnetical geological structures are clarified by a variety of tests, including those for demagnetization of the samples by stepwise applied alternating current and heat. 9 refs., 8 figs.

  14. Research report of FY 1997 on the environmentally acceptable coal utilization system feasibility survey. Environmentally acceptable coal utilization system feasibility survey in Malaysia and Vietnam (Malaysia); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Malaysia oyobi Vietnam ni okeru kankyo chowagata sekitan riyo system kanosei chosa (Malaysia ban))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In this survey, the coal utilization status in individual consumption sectors and coal distribution status in Malaysia are summarized as basic data for the introduction of environmentally acceptable coal utilization systems. In this fiscal year, the status of existing coal utilization technology and environmental issues in Malaysia are summarized as basic data for the introduction of above-mentioned systems on the basis of data and information collected by basic research and site survey in FY 1996. Malaysia is one of the rich countries producing the primary resources with crude petroleum, natural gas, hydro-power, and coal. The coal demand will be realized after saturating LNG development since 2000. The major coal consumption industries are power generation sector and cement industry sector. As expected increase in the future coal consumption, efficiency of coal utilization and environmental issues are problems in the future. Based on the FS results of this survey, the survey will be continued for planning and conducting the model project required from Malaysia. 8 figs., 34 tabs.

  15. Fiscal 1995 survey report on the feasibility study of the environmentally friendly type coal utilization system. Feasibility study of the environmentally friendly type coal utilization system in Thailand; Kankyo chowagata sekitan riyo system kanosei chosa. Tai ni okeru kankyo chowagata sekitan riyo system kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    The paper surveyed the present situation and future trend of economy, energy supply/demand, coal production/distribution/utilization and the environmental effects in Thailand. The survey on the coal utilization and its environmental effects was partially requested of the environmental research institute in Thailand. The amount of coal utilization in Thailand rapidly increased to nearly four times as large as that ten years ago mainly in terms of domestic lignite under the government`s policy on expansion of the domestic energy use. However, most of this domestic lignite is low-grade coal with low calories and high sulfur content, and the use of it was rapidly increased mostly in power generation sector without no adequate environmental measures taken. This caused an environmental problem on air pollution due to sulfur oxides at Mae Moh power plant in the north several years ago, and the damages to the regional residents, etc. were given much publicity by journalism and developed the social problem. Accordingly, Thai people are now critical of the coal resource exploration and the coal use expansion. Under the circumstances, the Ministry of Industry and the energy related ministries/offices are obliged to review their development/promotion plans. 84 figs., 99 tabs.

  16. Report on a project to support promotion of forming an environmentally friendly energy community. Survey on business feasibility of electric power generation utilizing combustible wastes solidified fuel in the Kishu and Kumano living area; Kankyo chowagata energy community keisei sokushin hojo jigyo chosa hokokusho. Kishu Kumano seikatsuken'iki ni okeru kanensei haikibutsu kokeika nenryo riyo hatsuden jigyo no jigyoka kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Surveys and discussions were given on business feasibility of a wide area RDF power generation system in the Kishu and Kumano living area. The discussions dealt with as wide area as transcending prefectural borders and including the southern parts of Mie and Nara Prefectures with the city of Shingu as the central part. Wastes generation amount is estimated to be about 70,000 tons at the present as wastes that can be turned into RDF, and to be decreased to 67,000 tons in 2018. The manufactured RDF has calorific power of 3500 to 4500 kcal/kg, two to three times greater than that of wastes. The RDF manufacturing facilities installed in cities, towns and villages have capacity of 30 to 50 tons a day, with that in the city of Shingu being the largest at about 78 tons a day. Transportation can be implemented most efficiently when road transportation is used. The RDF power generation system will consist of a fluid bed furnace, a plasma type ash melting furnace, and a bag filter plus activated carbon absorbing tower. The RDF manufacturing cost will be 27,900 yen per ton of wastes in the case of the city of Shingu. In terms of business profitability, the RDF power generation must find sources to pay 21,400 yen per ton of RDF even if the power sale revenue is considered. (NEDO)

  17. Ionization current in N2 gas. 11. Three dimensional analysis for loss processes of metastable particles affected by the reflection at the boundary; N2 gas chu ni okeru denri denryu. 11. Kyokai deno hansha wo koryoshita jun`antei reiki ryushi sonshitsu katei no sanjigen kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, S.; Ito, H.; Sekizawa, H.; Ikuta, N. [Chiba Institute of Technology, Chiba (Japan)

    1998-10-01

    Loss processes of the nitrogen metastable molecule N2(A{sup 3}{Sigma}u{sup +}) in plane parallel electrodes have been investigated by us previously by solving the diffusion equation. Our procedure is based on an analysis using the third kind of boundary condition which can take account of finite values for the density of N2(A{sup 3}{Sigma}u{sup +}) at the electrode surfaces. The values of the effective lifetime of N2(A{sup 3}{Sigma}u{sup +}) calculated from this analysis were reasonably consistent with our experiments. This paper describes the behavior of the effective lifetimes of N2(A{sup 3}{Sigma}u{sup +}) in a cylindrical cavity. The analytical treatment of the diffusion equation for N2(A{sup 3}{Sigma}u{sup +}) proposed by us is extended to the three dimensional space. We report the nature of the effective lifetimes of metastable molecule in the cylindrical cavity systematically. 16 refs., 9 figs.

  18. Fatigue life estimation of welded joints of an aluminium alloy under superimposed random load waves (follow-up report). Effects of high frequency components; Jujo random kajuka ni okeru aluminium gokin yosetsu tsugite no hiro jumyo suitei (zokuho). Koshuha seibun no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, I.; Maenaka, H.; Takada, A. [Ship Research Inst., Tokyo (Japan)

    1996-12-31

    In order to examine fatigue behavior of boxing welded joints of anticorrosion aluminum A 5083 P-O alloy, the residual stress measurements, static loading tests, elastic finite element analyses, constant amplitude fatigue tests, and random fatigue tests were conducted. For a load wave in the random loading fatigue tests, a direct current component, a zero-mean narrow band random process, and a high frequency component were combined and superimposed, to examine the effect of the high frequency component and the effect of the stress cycle count method and the mean stress correction on the life estimation. For the fatigue analysis, a reference stress, such as that considering the structural stress concentration, was proved effective in reducing the amount of scattering in the fatigue test results and in improving the life estimation accuracy. Accordingly, for the actual scale measurements, it is insufficient only to measure the stress at points far from the crack initiation place. It is required to analyze the fatigue by measuring the reference stress same as the basic data acquisition tests in the laboratory. 4 refs., 21 figs., 4 tabs.

  19. Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Feasibility study of the environmentally friendly type coal utilization system in Thailand; Kankyo chowagata sekitan riyo system kanosei chosa. Tai ni okeru kankyo chowagata sekitan riyo system kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper investigated and studied the present situation and future trend of coal utilization and distribution in Thailand, and the present situation of environmental effects and the measures taken for environmental protection. Around 2010, coal will probably be produced only at EGAT`s Mae Moh (MM) coal mine. Demand for overseas coal is expected to be 40-50 million tons in 2011, and preparation of the coal center becomes a subject. For general industry use coal, pretreatment such as coal preparation, coal blending and briquetting is needed, considering coal quality, usage, transport distance and environmental effects. Brown coal of MM coal mine is a lignite with high sulfur, high ash content and low heating value. Wide spread of its use can be expected if upgrading is possible such as desulfurization, deashing, increasing heating value. In the electric power generation field, the absorber was installed at the existing boiler of the mine-mouth generating plant to conduct a verification test on high grade desulfurization of ultra-high sulfur lignite. In the industry field, the circulating fluidized bed boiler was adopted. In the residential/commercial field, introduction of briquette was proposed. 80 refs., 84 tabs.

  20. FY 2000 report on the basic survey to promote Joint Implementation, etc. Survey of the effective use of wastes at palm oil refineries; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Palm oil seisei kojo ni okeru haikibutsu yuko riyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As to empty fruit bunches (EFB) which are wasted at the Lahad Datu plant of Felda Vegetable Oil Products Co. in Malaysia, a project was studied for energy substitution and greenhouse effect gas reduction by fluidized bed cogeneration facilities using this as fuel. In the project, studied was the introduction of on-site cogenerator of 7,800kW in generating-end output, and that of IPP cogenerator of 16,000kW as reference. As a result of the study, the energy substitution amount in toe in 20 years was approximately 376 k tons in case of on-site power generation/fluidized bed boiler and approximately 695 k tons in case of IPP and fluidized bed boiler. The amount of greenhouse effect gas emission in toe in 20 years was approximately 5,757 k tons and 11,654 k tons, respectively. Concerning the profitability, the internal earning rate was 3.32-8.47% in case of on-site power generation/fluidized bed boiler and 9.13-14.65% in case of IPP/fluidized bed boiler. It indicated the materialization of the project. (NEDO)

  1. From Water Oxidation to Reduction: Transformation from Ni(x)Co(3-x)O4 Nanowires to NiCo/NiCoO(x) Heterostructures.

    Science.gov (United States)

    Yan, Xiaodong; Li, KeXue; Lyu, Lu; Song, Fang; He, Jun; Niu, Dongmei; Liu, Lei; Hu, Xile; Chen, Xiaobo

    2016-02-10

    A homologous Ni-Co based nanowire catalyst pair, composed of Ni(x)Co(3-x)O4 nanowires and NiCo/NiCoO(x) nanohybrid, is developed for efficient overall water splitting. Ni(x)Co(3-x)O4 nanowires are found as a highly active oxygen evolution reaction (OER) catalyst, and they are converted into a highly active hydrogen evolution reaction (HER) catalyst through hydrogenation treatment as NiCo/NiCoO(x) heteronanostructures. An OER current density of 10 mA cm(-2) is obtained with the Ni(x)Co(3-x)O4 nanowires under an overpotential of 337 mV in 1.0 M KOH, and an HER current density of 10 mA cm(-2) is obtained with the NiCo/NiCoO(x) heteronanostructures at an overpotential of 155 mV. When integrated in an electrolyzer, these catalysts demonstrate a stable performance in water splitting. PMID:26784862

  2. Thermal stability of electrodeposited Ni and Ni-Co layers; an EBSD-study

    DEFF Research Database (Denmark)

    Rasmussen, Anette Alsted; Gholinia, A.; Trimby, P.W.; Somers, Marcel A.J.

    The influence of heat treatment on the microstructure and the microtexture of electrodeposited Ni and Ni-Co layers was investigated with Electron Backscatter Diffraction (EBSD) with high resolution. Samples were annealed for 1 hour at 523 K and 673 K, the temperature region wherein recrystallisat...... recrystallisation occurs. The results are discussed in relation to the resolution of EBSD for the very fine grained electrodeposits and previous X-ray diffracton investigations.......The influence of heat treatment on the microstructure and the microtexture of electrodeposited Ni and Ni-Co layers was investigated with Electron Backscatter Diffraction (EBSD) with high resolution. Samples were annealed for 1 hour at 523 K and 673 K, the temperature region wherein...

  3. Microscopic domain structures in unidirectional and isotropic exchange-coupled NiO/NiFe bilayers

    International Nuclear Information System (INIS)

    The dependence on nickel oxide thickness in unidirectional and isotropic exchange-coupled NiO/NiFe bilayer films was investigated by magnetic force microscopy to better understand exchange biasing at microscopic length scales. As the NiO thickness increased, the domain structure of unidirectional biased films formed smaller and more complex in-plane domains. By contrast, for the isotropically coupled films, large domains generally formed with increasing NiO thickness including a new cross type domain with out-of-plane magnetization orientation. The density of the cross domain is proportional to exchange biasing field, and the fact that the domain mainly originated from the strongest exchange coupled region was confirmed by imaging in an applied external field during a magnetization cycle

  4. Transformation characteristics of TiNi/TiNi alloys synthesized by explosive welding

    Institute of Scientific and Technical Information of China (English)

    LI Juntao; ZHENG Yanjun; CUI Lishan

    2007-01-01

    Effects of severe deformation and heat treatment on the transformation behaviors of explosively welded duplex TiNi/TiNi shape memory alloys(SMAs)were investigated by the differential scanning calorimeter (DSC).The explosively welded duplex TiNi/TiNi plate of 0.7mm in thickness was cold-rolled at room temperature to the extent of 60%reduction in thickness and then annealed at different temperatures (573-973K)for different time(15min-10h).Low temperature(623-723K)heat treatment led to amorphous crystallization.At higher temperature(873K),the re-crystallization took place in the specimens.Analysis showed that the change of internal stresses is iust the root cause of the change of transformation temperature.The relationships between the transformation behaviors and the heat treatment were discussed in the present report.

  5. Synthetic Ni3S2/Ni hybrid architectures as potential contrast agents in MRI

    Science.gov (United States)

    Ma, J.; Chen, K.

    2016-04-01

    Traditional magnetic resonance imaging (MRI) contrast agents mainly include superparamagnetic (SPM) iron oxide nanoparticle as T 2 contrast agent for liver and paramagnetic Gd (III)-chelate as T 1 contrast agent for all organs. In this work, weak ferromagnetic kale-like and SPM cabbage-like Ni3S2@Ni hybrid architectures were synthesized and evaluated as potential T 1 MRI contrast agents. Their relatively small r 2/r 1 ratios of 2.59 and 2.38, and high r 1 values of 11.27 and 4.89 mmol‑1 L s‑1 (for the kale-like and cabbage-like Ni3S2@Ni, respectively) will shed some light on the development of new-type MRI contrast agents.

  6. Microstructure and magnetic properties of Ti/Ni/Ti in dependence on Ni layer thickness

    Institute of Scientific and Technical Information of China (English)

    ZHANG Hanwei; FENG Shunzhen; ZHANG Yujie; SUN Huiyuan

    2006-01-01

    The films of Ti(15 nm)/Ni(t nm)/Ti(15 nm)(t=20, 30, 40, 50) were prepared by dc magnetron sputtering at room temperature and subsequent annealing at 400 ℃ for 30 min. Scanning probe microscope (SPM), vibrating sample magnetometer (VSM) and X-ray diffraction (XRD) were applied to study the magnetic properties and microstructure. AFM images show that small and uniform grains and some clusters appear with the increase of Ni thickness, also MFM images show that the size of domain first decreases and then increases. The coercivity reaches the maximum 48 kA·m-1 at t=30 nm. The XRD profiles show stronger fcc (111) orientation peak of Ni and weak hcp structure peaks of Ni3Ti. This results reveal that the crystal lines have the prefer orientation and achieve the ordered.

  7. Effects of reversible shape memory and aging in the Ni-50.5 at. % Ni alloy

    International Nuclear Information System (INIS)

    By the method of dilatometry and transmission electron microscopy the effects of reversible shape memory (ERSM) and structural changes in alloy Ti-50.5 at. % Ni after rolling in austenitic state and various thermal treatments were studied. it is ascertained that the alloy in non-deformed state is an aging one the process of Ti3Ni4 particles isolation takes place during long-term holding at temperatures approximately 150 deg C lower than in alloy Ti-51 at. % Ni. Deformation accelerates the process of particle isolation by two orders. It is shown that the deformation value during ERSM correlates with Ti3Ni4 particles dissolution-isolation, if alloy has not been recrystallized. Memory of reversible shape memory effect (double memory) was revealed, stemming from regular isolation of particles in deformed B2-phase and texture retaining in their arrangement

  8. Evolution of collectivity in the 78Ni region: Coulomb excitation of 74Ni at intermediate energies.

    Directory of Open Access Journals (Sweden)

    Marchi T.

    2014-03-01

    Full Text Available The study of the collective properties of nuclear excitations far from stability provides information about the shell structure at extreme conditions. Spectroscopic observables such as the energy or the transition probabilities of the lowest states, in nuclei with large neutron excess, allow to probe the density and isospin dependence of the effective interaction. Indeed, it was recently shown that tensor and three-body forces play an important role in breaking and creating magic numbers. Emblematic is the case of the evolution of the Ni isotopic chain where several features showed up moving from the most neutron rich stable isotope (64Ni towards the 78Ni nucleus where the large neutron excess coincides with a double shell closure. In this framework, we have recently performed an experiment with the goal to extract the B(E2; 0+ → 2+ value for the 74Ni nucleus in an intermediate-energy Coulomb excitation experiment: preliminary results are discussed.

  9. Magnetic transitions in Ni1-xMox and Ni1-xWx disordered alloys

    International Nuclear Information System (INIS)

    We present a mean-field study of the magnetic phase diagram of Ni1-xMox and Ni1-xWx alloys. The pair energies that enter the internal energy part of the free energy are obtained from a first-principles calculation. We try to understand why spin-glass phase is not observed in these alloys. - Highlights: → We have used the augmented space technique to study the electronic structure of NiMo and NiW. → Using the Lichtenstein formula we have obtained the exchange interactions in the alloys. → We have studied the mean-field magnetic phase diagram for the alloys. → The idea was to investigate why no spin-glass phase is not found in these alloys.

  10. Mechanical properties of NiO/Ni-YSZ composites depending on temperature, porosity and redox cycling

    DEFF Research Database (Denmark)

    Pihlatie, Mikko; Kaiser, Andreas; Mogensen, Mogens Bjerg

    2009-01-01

    with the Neel temperature, 250 degrees C, of NiO was observed. Above this temperature, a linear decrease occurred. Specific damping showed a peak at 170-180 degrees C and increased above ca. 1000 degrees C in NiO-YSZ. In the reduced state the elastic modulus decreased linearly with temperature......The Impulse Excitation Technique (IET) was used to determine the elastic modulus and specific damping of different Ni/NiO-YSZ composites suitable for use in solid oxide fuel cells (SOFC). The porosity of the as-sintered samples varied from 9 to 38% and that of the reduced ones from 31 to 52%. For...... all samples a linear relation between Young's modulus and porosity was found. The temperature dependency of the mechanical properties of both as-sintered and reduced composites was investigated by IET up to 1200 degrees C. In the as-sintered state, first an increase and peak of stiffness coinciding...

  11. Desmontando a ni-ni. Un estereotipo juvenil en tiempos de crisis

    OpenAIRE

    Navarrete Moreno, Lorenzo; Caro Sagüés, Gonzalo; Carreras, Enrique; de Francisco, Rafael; Gastón Faci, Diego; Roldán, Adela; Gutierrez Villalta, Jesús; Zúñiga Contreras, Ricardo

    2011-01-01

    El objetivo de este estudio es conocer la realidad social de los/las jóvenes españoles en situaciones vitales de inactividad laboral y formativa, tanto en sus parámetros demográficos como en relación a la actividad, la educación (en distintos niveles), otros tipos de formación, y su situación económica y familiar, (población del colectivo de jóvenes españoles que ni estudian ni trabajan), desde una visión informada y pormenorizada sociológicamente de dicho asunto. Este colectivo ni-ni se ...

  12. Ni based silicides for 45 nm CMOS and beyond

    Energy Technology Data Exchange (ETDEWEB)

    Lauwers, Anne [IMEC, Kapeldreef 75, 3001 Leuven (Belgium)]. E-mail: lauwersa@imec.be; Kittl, Jorge A. [IMEC, Texas Instruments (Belgium); Van Dal, Mark J.H. [IMEC, Philips Research Leuven (Belgium); Chamirian, Oxana [IMEC, Kapeldreef 75, 3001 Leuven (Belgium); Pawlak, Malgorzata A. [IMEC, Kapeldreef 75, 3001 Leuven (Belgium); Potter, Muriel de [IMEC, Kapeldreef 75, 3001 Leuven (Belgium); Lindsay, Richard [IMEC, Kapeldreef 75, 3001 Leuven (Belgium); Raymakers, Toon [Philips Research Laboratories, Prof. Holstlaan 4, 5656 AA Eindhoven (Netherlands); Pages, Xavier [IMEC, ASM Belgium (Belgium); Mebarki, Bencherki [Applied Materials (Belgium); Mandrekar, Tushar [Applied Materials Inc., Santa Clara, CA (United States); Maex, Karen [IMEC, Kapeldreef 75, 3001 Leuven (Belgium)

    2004-12-15

    Material issues that impact the applicability of Ni based silicides to CMOS flows were studied, including the excessive silicidation of narrow features, the growth kinetics of Ni{sub 2}Si and NiSi on single-crystalline and poly-crystalline silicon and the thermal degradation mechanisms. Ni{sub 2}Si was found to grow by diffusion controlled kinetics with an activation energy of about 1.55 eV on single-crystalline Si. As a result, the excessive silicidation in small features can be reduced in a 2-step Ni-silicide process by reducing the thermal budget of the first RTP step. The mechanisms of thermal degradation of NiSi were studied. Thin NiSi films were found to degrade morphologically while still in the monosilicide phase. Thick NiSi films degrade morphologically at low temperatures and by transformation to NiSi{sub 2} at high temperatures. The reaction of Ni with SiGe substrates and the effect of Ge on the thermal degradation of the Ni-germanosilicide were investigated. Activation energies for the thermal degradation of Ni(SiGe) on SiGe were found to be significantly smaller than the values found for the thermal degradation of NiSi on pure Si. The effect of alloying Ni with Pt or Ta was studied. NiSi films alloyed with Pt or Ta are found to be thermally more stable compared to pure NiSi. Alloying with Pt was found to improve the thermal stability of NiSi on narrow poly-Si gates. The kinetics of Ni{sub 2}Si and NiSi formation on poly silicon were determined as well as their dependence on dopants. The presence of B in high doses was found to slow down the silicide formation significantly. Dopant segregation to the NiSi/oxide interface was observed, which is believed to be responsible for the observed shifts in work function. The sheet resistance of fully Ni-silicided 100 nm poly Si/oxide stacks is found to be stable up to 800 deg. C.

  13. Ni based silicides for 45 nm CMOS and beyond

    International Nuclear Information System (INIS)

    Material issues that impact the applicability of Ni based silicides to CMOS flows were studied, including the excessive silicidation of narrow features, the growth kinetics of Ni2Si and NiSi on single-crystalline and poly-crystalline silicon and the thermal degradation mechanisms. Ni2Si was found to grow by diffusion controlled kinetics with an activation energy of about 1.55 eV on single-crystalline Si. As a result, the excessive silicidation in small features can be reduced in a 2-step Ni-silicide process by reducing the thermal budget of the first RTP step. The mechanisms of thermal degradation of NiSi were studied. Thin NiSi films were found to degrade morphologically while still in the monosilicide phase. Thick NiSi films degrade morphologically at low temperatures and by transformation to NiSi2 at high temperatures. The reaction of Ni with SiGe substrates and the effect of Ge on the thermal degradation of the Ni-germanosilicide were investigated. Activation energies for the thermal degradation of Ni(SiGe) on SiGe were found to be significantly smaller than the values found for the thermal degradation of NiSi on pure Si. The effect of alloying Ni with Pt or Ta was studied. NiSi films alloyed with Pt or Ta are found to be thermally more stable compared to pure NiSi. Alloying with Pt was found to improve the thermal stability of NiSi on narrow poly-Si gates. The kinetics of Ni2Si and NiSi formation on poly silicon were determined as well as their dependence on dopants. The presence of B in high doses was found to slow down the silicide formation significantly. Dopant segregation to the NiSi/oxide interface was observed, which is believed to be responsible for the observed shifts in work function. The sheet resistance of fully Ni-silicided 100 nm poly Si/oxide stacks is found to be stable up to 800 deg. C

  14. Magnetic Irreversibility in VO2/Ni Bilayers

    Science.gov (United States)

    de La Venta, Jose; Lauzier, Josh; Sutton, Logan

    The temperature dependence of the coercivity and magnetization of VO2/Ni bilayers was studied. VO2 exhibits a well-known Structural Phase Transition (SPT) at 330-340 K, from a low temperature monoclinic (M) to a high temperature rutile (R) structure. The SPT of VO2 induces an inverse magnetoelastic effect that strongly modifies the coercivity and magnetization of the Ni films. In addition, the growth conditions allow tuning of the magnetic properties. Ni films deposited on top of VO2 (M) show an irreversible change in the coercivity after the first cycle through the high temperature phase, with a corresponding change in the surface morphology of VO2. On the other hand, the Ni films grown on top of VO2 (R) do not show this irreversibility. These results indicate that properties of magnetic films are strongly affected by the strain induced by materials that undergo SPT and that it is possible to control the magnetic properties by tuning the growth conditions.

  15. Interface stress in Au/Ni multilayers

    DEFF Research Database (Denmark)

    Schweitz, K.O.; Böttiger, J.; Chevallier, J.; Feidenhans'l, Robert Krarup; Nielsen, Martin Meedom; Rasmussen, Frank Berg

    2000-01-01

    The effect of intermixing on the apparent interface stress is studied in < 111 >-textured dc-magnetron sputtered Au/Ni multilayers by use of two methods commonly used for determining interface stress. The method using profilometry and in-plane x-ray diffraction does not take intermixing into...

  16. Dolor en niños.

    Directory of Open Access Journals (Sweden)

    María Ana Tovar

    2009-11-01

    Full Text Available La definición hecha por la Asociación Internacional para el Estudio del Dolor-IASP se debe ampliar cuando se considera el dolor en los niños, para incluir indicadores de conducta y fisiológicos, porque muchos no pueden verbalizar su dolor. Se ha demostrado que las estructuras anatómicas necesarias para la percepción del dolor son funcionales en el segundo trimestre del embarazo, pero hay diferencias en la transmisión y modulación del dolor cuando se comparan con los adultos. El aprendizaje acerca del dolor ocurre con la primera experiencia dolorosa. En la percepción del dolor del niño influyen factores biológicos, cognoscitivos, psicológicos y socioculturales. La evaluación del dolor en los niños se hace a través de técnicas de auto-informe, de observación en el comportamiento y de medidas fisiológicas. Finalmente, cuando se considere el manejo del dolor es necesario eliminar los mitos alrededor del uso de analgésicos opioides en los niños.

  17. Dolor en niños

    Directory of Open Access Journals (Sweden)

    María Ana Tovar

    2005-12-01

    Full Text Available La definición hecha por la Asociación Internacional para el Estudio del Dolor-IASP se debe ampliar cuando se considera el dolor en los niños, para incluir indicadores de conducta y fisiológicos, porque muchos no pueden verbalizar su dolor. Se ha demostrado que las estructuras anatómicas necesarias para la percepción del dolor son funcionales en el segundo trimestre del embarazo, pero hay diferencias en la transmisión y modulación del dolor cuando se comparan con los adultos. El aprendizaje acerca del dolor ocurre con la primera experiencia dolorosa. En la percepción del dolor del niño influyen factores biológicos, cognoscitivos, psicológicos y socioculturales. La evaluación del dolor en los niños se hace a través de técnicas de auto-informe, de observación en el comportamiento y de medidas fisiológicas. Finalmente, cuando se considere el manejo del dolor es necesario eliminar los mitos alrededor del uso de analgésicos opioides en los niños.

  18. Annealing Ni nanocrystalline on WC-Co

    International Nuclear Information System (INIS)

    The effects of annealing temperature on nanocrystalline sputter-deposited Ni thin films (500 nm) deposited on WC-Co (4 wt.%) were investigated. Special attention was focused on quantitative evaluation of residual stress and Ni diffusion into the WC-Co, after heat treatment, from 873 to 1273 K. The estimated level of residual stress, as measured by X-ray diffraction, is around -1.3 ± 0.1 GPa for the as-deposited film, whereas after annealing at 1273 K it decreases significantly. Atomic force microscopy shows that high annealing temperature results into an exponential increase of the roughness. An intermixing between the nanocrystalline Ni and the Co from WC substrate occurs, as it is revealed by quantitative depth-resolved Rutherford backscattering spectrometry analysis and also supported by X-ray photoelectron spectroscopy. We ascribe a significant stress relief with the increasing annealing temperature to the diffusion process. The understanding of this process is particularly important in WC-Co parts with the surface treated with Ni in order to improve the maximum surface service temperature.

  19. Annealing Ni nanocrystalline on WC-Co

    Energy Technology Data Exchange (ETDEWEB)

    Fernandes, C.M.; Guisbiers, G.; Pereira, S. [CICECO, University of Aveiro, 3810-193 Aveiro (Portugal); Barradas, N.P.; Alves, E. [Nuclear and Technological Institute, E.N. 10, 2686-953 Sacavem (Portugal); Senos, A.M.R., E-mail: anamor@ua.p [CICECO, University of Aveiro, 3810-193 Aveiro (Portugal); Vieira, M.T. [Mechanical Engineering Department, ICEMS, Polo II, 3030-201 Coimbra (Portugal)

    2009-08-12

    The effects of annealing temperature on nanocrystalline sputter-deposited Ni thin films (500 nm) deposited on WC-Co (4 wt.%) were investigated. Special attention was focused on quantitative evaluation of residual stress and Ni diffusion into the WC-Co, after heat treatment, from 873 to 1273 K. The estimated level of residual stress, as measured by X-ray diffraction, is around -1.3 +- 0.1 GPa for the as-deposited film, whereas after annealing at 1273 K it decreases significantly. Atomic force microscopy shows that high annealing temperature results into an exponential increase of the roughness. An intermixing between the nanocrystalline Ni and the Co from WC substrate occurs, as it is revealed by quantitative depth-resolved Rutherford backscattering spectrometry analysis and also supported by X-ray photoelectron spectroscopy. We ascribe a significant stress relief with the increasing annealing temperature to the diffusion process. The understanding of this process is particularly important in WC-Co parts with the surface treated with Ni in order to improve the maximum surface service temperature.

  20. Electroplating condition for Ni nanocrystalline on metal (Ni and Cu) plates

    Energy Technology Data Exchange (ETDEWEB)

    Park, Keun Yung; Uhm, Young Rang; Son, Kwang Jae; Shim, Young Ho; Choi, Sun Ju [KAERI, Daejeon (Korea, Republic of)

    2012-10-15

    Ni 63, a beta radiation source, is prepared by the electrical deposition of radioactive Ni 63 ions on a thin non radioactive nickel foil or Cu plate. Given a half life of 100 years, a nuclear battery will still produce half of its initial starting power after 100 years. A speck of a radioisotope like nickel 63, for example, contains enough energy to power a nano nuclear battery for decades, and to do so safely. Ni 63 plating is similar to other electroplating processes that employ soluble metal anodes. It requires the passage of a direct current between two electrodes that are immersed in a conductive, aqueous solution of nickel salts. The charged Ni ions are formed by sulfate, sulfamate, chloride, and a Watts bath. However, the charged Ni 63 ions are formed by dissolving metal Ni 63. To established the coating condition of Ni 63, non radioactive metal Ni particles are dissolved an acid solution and electroplated on a Ni sheet. The nickel plating process is used extensively for decorative, engineering and electro forming purposes because the appearance and other properties of electrodeposited nickel can be varied over a wide range by controlling the composition and operating parameters of the plating solution. A continuous increase in the grain size versus current density has also been recognized in the direct current electrodeposition of nickel coating. On the other hand, A runa et al. reported that the current density has no significant effect on the grain size of nickel electro deposits. A review of the literature shows that saccharin has often been added to a nickel plating bath since the 1980s to improve the ductility and brightness, and in later periods as a grain refiner agent. In the present paper, not only the preparation of a Ni plating solution prepared by dissolving metal particles, but also an optimization of the deposition conditions, such as the current density, saccharin concentration in the bath, and different metal substrates were investigated