WorldWideScience

Sample records for chrysotile-containing joint compounds

  1. Potential artifacts associated with historical preparation of joint compound samples and reported airborne asbestos concentrations.

    Science.gov (United States)

    Brorby, G P; Sheehan, P J; Berman, D W; Bogen, K T; Holm, S E

    2011-05-01

    Airborne samples collected in the 1970s for drywall workers using asbestos-containing joint compounds were likely prepared and analyzed according to National Institute of Occupational Safety and Health Method P&CAM 239, the historical precursor to current Method 7400. Experimentation with a re-created, chrysotile-containing, carbonate-based joint compound suggested that analysis following sample preparation by the historical vs. current method produces different fiber counts, likely because of an interaction between the different clearing and mounting chemicals used and the carbonate-based joint compound matrix. Differences were also observed during analysis using Method 7402, depending on whether acetic acid/dimethylformamide or acetone was used during preparation to collapse the filter. Specifically, air samples of sanded chrysotile-containing joint compound prepared by the historical method yielded fiber counts significantly greater (average of 1.7-fold, 95% confidence interval: 1.5- to 2.0-fold) than those obtained by the current method. In addition, air samples prepared by Method 7402 using acetic acid/dimethylformamide yielded fiber counts that were greater (2.8-fold, 95% confidence interval: 2.5- to 3.2-fold) than those prepared by this method using acetone. These results indicated (1) there is an interaction between Method P&CAM 239 preparation chemicals and the carbonate-based joint compound matrix that reveals fibers that were previously bound in the matrix, and (2) the same appeared to be true for Method 7402 preparation chemicals acetic acid/dimethylformamide. This difference in fiber counts is the opposite of what has been reported historically for samples of relatively pure chrysotile dusts prepared using the same chemicals. This preparation artifact should be considered when interpreting historical air samples for drywall workers prepared by Method P&CAM 239. PMID:21462068

  2. Inhibition of the formation of intermetallic compounds in aluminum-steel welded joints by friction stir welding

    OpenAIRE

    Torres López, Edwar A.; Ramirez, Antonio J.

    2015-01-01

    Formation of deleterious phases during welding of aluminum and steel is a challenge of the welding processes, for decades. Friction Stir Welding (FSW) has been used in an attempt to reduce formation of intermetallic compounds trough reducing the heat input. In this research, dissimilar joint of 6063-T5 aluminum alloy and AISI-SAE 1020 steel were welded using this technique. The temperature of welded joints was measured during the process. The interface of the welded joints was characterized u...

  3. Ruin Probability and Joint Distributions of Some Actuarial Random Vectors in the Compound Pascal Model

    Institute of Scientific and Technical Information of China (English)

    Xian-min Geng; Shu-chen Wan

    2011-01-01

    The compound negative binomial model, introduced in this paper, is a discrete time version. We discuss the Markov properties of the surplus process, and study the ruin probability and the joint distributions of actuarial random vectors in this model. By the strong Markov property and the mass function of a defective renewal sequence, we obtain the explicit expressions of the ruin probability, the finite-horizon ruin probability,the joint distributions of T, U(T - 1), |U(T)| and inf 0≤n<T1 U(n) (i.e., the time of ruin, the surplus immediately before ruin, the deficit at ruin and maximal deficit from ruin to recovery) and the distributions of some actuariai random vectors.

  4. Inhibition of the formation of intermetallic compounds in aluminum-steel welded joints by friction stir welding

    International Nuclear Information System (INIS)

    Formation of deleterious phases during welding of aluminum and steel is a challenge of the welding processes, for decades. Friction Stir Welding (FSW) has been used in an attempt to reduce formation of intermetallic compounds trough reducing the heat input. In this research, dissimilar joint of 6063-T5 aluminum alloy and AISI-SAE 1020 steel were welded using this technique. The temperature of welded joints was measured during the process. The interface of the welded joints was characterized using optical microscopy, scanning and transmission electron microscopy. Additionally, composition measurements were carried out by X-EDS and DRX. The experimental results revealed that the maximum temperature on the joint studied is less than 360 degree centigrade. The microstructural characterization in the aluminum-steel interface showed the absence of intermetallic compounds, which is a condition attributed to the use of welding with low thermal input parameters. (Author)

  5. Effects of bismuth on growth of intermetallic compounds in Sn-Ag-Cu Pb-free solder joints

    Institute of Scientific and Technical Information of China (English)

    LI Guo-yuan; SHI Xun-qing

    2006-01-01

    The effects of Bi addition on the growth of intermetallic compound (IMC) formation in Sn-3.8Ag-0.7Cu solder joints were investigated. The test samples were prepared by conventional surface mounting technology. To investigate the element diffusion and the growth kinetics of intermetallics formation in solder joint,isothermal aging test was performed at temperatures of 100,150,and 190 ℃,respectively. The optical microscope (OM) and scanning electron microscope (SEM) were used to observe microstructure evolution of solder joint and to estimate the thickness and the grain size of the intermetallic layers. The IMC phases were identified by energy dispersive X-ray (EDX) and X-ray diffractometer (XRD). The results clearly show that adding about 1.0% Bi in Sn-Ag-Cu solder alloy system can refine the grain size of the IMC and inhibit the excessive IMC growth in solder joints,and therefore improve the reliability of the Pb-free solder joints. Through observation of the microstructural evolution of the solder joints,the mechanism of inhibition of IMC growth due to Bi addition was proposed.

  6. Compound characterization of laser brazed SiC-steel joints using tungsten reinforced SnAgTi-alloys

    Science.gov (United States)

    Südmeyer, I.; Rohde, M.; Fürst, T.

    2010-02-01

    With the help of a CO2-laser (λ = 10.64 μm) Silicon carbide (Trade name: Ekasic-F, Comp: ESK Ceramics) has been brazed to commercial steel (C45E, Matnr. 1.1191) using SnAgTi-filler alloys. The braze pellets were dry pressed based on commercially available powders and polished to a thickness of 300 μm. The SnAgTi-fractions were varied with the objective of improving the compound strength. Furthermore, tungsten reinforced SnAgTi-fillers were examined with regard to the shear strength of the ceramic/steel joints. Polished microsections of SnAgTi-pellets were investigated before brazing in order to evaluate the particle distribution and to detect potential porosities using optical microscopy. The brazing temperature and the influence of the reinforcing particles on the active braze filler were determined by measurements with a differential scanning calorimeter (DSC). After brazing. the ceramic-steel joints were characterized by scanning electron micrographs and EDX-analysis. Finally the mechanical strength of the braze-joints was determined by shear tests.

  7. Design of a Slowed-Rotor Compound Helicopter for Future Joint Service Missions

    Science.gov (United States)

    Silva, Christopher; Yeo, Hyeonsoo; Johnson, Wayne R.

    2010-01-01

    A slowed-rotor compound helicopter has been synthesized using the NASA Design and Analysis of Rotorcraft (NDARC) conceptual design software. An overview of the design process and the capabilities of NDARC are presented. The benefits of trading rotor speed, wing-rotor lift share, and trim strategies are presented for an example set of sizing conditions and missions.

  8. Inhibition of the formation of intermetallic compounds in aluminum-steel welded joints by friction stir welding

    Directory of Open Access Journals (Sweden)

    Torres López, Edwar A.

    2015-12-01

    Full Text Available Formation of deleterious phases during welding of aluminum and steel is a challenge of the welding processes, for decades. Friction Stir Welding (FSW has been used in an attempt to reduce formation of intermetallic compounds trough reducing the heat input. In this research, dissimilar joint of 6063-T5 aluminum alloy and AISI-SAE 1020 steel were welded using this technique. The temperature of welded joints was measured during the process. The interface of the welded joints was characterized using optical microscopy, scanning and transmission electron microscopy. Additionally, composition measurements were carried out by X-EDS and DRX. The experimental results revealed that the maximum temperature on the joint studied is less than 360 °C. The microstructural characterization in the aluminum-steel interface showed the absence of intermetallic compounds, which is a condition attributed to the use of welding with low thermal input parameters.La unión de juntas aluminio-acero, sin la formación de fases deletéreas del tipo FexAly, ha sido, por décadas, un desafío para los procesos de soldadura. La soldadura por fricción-agitación ha sido empleada para intentar reducir el aporte térmico y evitar la formación de compuestos intermetálicos. Usando esta técnica fueron soldadas juntas disimilares de aluminio 6063-T5 y acero AISI-SAE 1020. La soldadura fue acompañada de medidas de temperatura durante su ejecución. La interfase de las juntas soldadas fue caracterizada utilizando microscopía óptica, electrónica de barrido y electrónica de transmisión. Adicionalmente fueron realizadas medidas puntuales X-EDS y DRX. Los resultados experimentales revelan que la temperatura máxima en la junta es inferior a 360 °C. La caracterización microestructural en la interfase aluminio-acero demostró la ausencia de compuestos intermetálicos, condición atribuida al uso de parámetros de soldadura con bajo aporte térmico.

  9. Growth behavior of intermetallic compounds at Sn–Ag/Cu joint interfaces revealed by 3D imaging

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Q.K., E-mail: qkzhang@alum.imr.ac.cn [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); State Key Laboratory of Advanced Brazing Filler Metals & Technology, Zhengzhou Research Institute of Mechanical Engineering, Zhengzhou 450001 (China); Long, W.M. [State Key Laboratory of Advanced Brazing Filler Metals & Technology, Zhengzhou Research Institute of Mechanical Engineering, Zhengzhou 450001 (China); Zhang, Z.F., E-mail: zhfzhang@imr.ac.cn [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China)

    2015-10-15

    In this study, the morphologies of intermetallic compounds (IMCs) at the as-soldered and thermal aged Sn–Ag/Cu joint interfaces were observed by SEM and measured using Laser Confocal Microscope, and their three-dimensional (3D) shapes were revealed using 3D imaging technology. The observation reveal that during the soldering process the Cu{sub 6}Sn{sub 5} grains at the joint interface evolve from hemispheroid to a bamboo shoot-shaped body with increasing liquid state reacting time, and their grain size increases sharply. After thermal aging, the Cu{sub 6}Sn{sub 5} grains change into equiaxed grains, while the top of some prominent Cu{sub 6}Sn{sub 5} grains changes little. Due to the higher active energy of the Sn atoms at the grain boundary, the growth rate of IMC grains around the grain boundaries of the solder is higher during the aging process. From the evolution in morphology of the IMC layer, it is demonstrated that the IMC layer grows through grain boundary diffusion of the Cu and Sn atoms during the aging process, and the volume diffusion is very little. The 3D imaging technology is used to reveal the shape and dimension of the IMC grains. - Highlights: • Morphologies of IMCs at the Sn–Ag/Cu interface were revealed by 3D imaging. • Preferential growth of IMCs around the solder grain boundaries was observed. • Growth behaviors of IMCs during reflowing and aging process were investigated.

  10. Growth behavior of intermetallic compounds at Sn–Ag/Cu joint interfaces revealed by 3D imaging

    International Nuclear Information System (INIS)

    In this study, the morphologies of intermetallic compounds (IMCs) at the as-soldered and thermal aged Sn–Ag/Cu joint interfaces were observed by SEM and measured using Laser Confocal Microscope, and their three-dimensional (3D) shapes were revealed using 3D imaging technology. The observation reveal that during the soldering process the Cu6Sn5 grains at the joint interface evolve from hemispheroid to a bamboo shoot-shaped body with increasing liquid state reacting time, and their grain size increases sharply. After thermal aging, the Cu6Sn5 grains change into equiaxed grains, while the top of some prominent Cu6Sn5 grains changes little. Due to the higher active energy of the Sn atoms at the grain boundary, the growth rate of IMC grains around the grain boundaries of the solder is higher during the aging process. From the evolution in morphology of the IMC layer, it is demonstrated that the IMC layer grows through grain boundary diffusion of the Cu and Sn atoms during the aging process, and the volume diffusion is very little. The 3D imaging technology is used to reveal the shape and dimension of the IMC grains. - Highlights: • Morphologies of IMCs at the Sn–Ag/Cu interface were revealed by 3D imaging. • Preferential growth of IMCs around the solder grain boundaries was observed. • Growth behaviors of IMCs during reflowing and aging process were investigated

  11. EFFECT OF LASER INPUT ENERGY ON AuSnx INTERMETALLIC COMPOUNDS FORMATION IN SOLDER JOINTS WITH DIFFERENT THICKNESS OF Au SURFACE FINISH ON PADS

    Institute of Scientific and Technical Information of China (English)

    W.Liu; C.Q.Wang; Y.H.Tian; M.Y.Li

    2008-01-01

    Formation of AuSnx intermetallic compounds (IMCs) in laser reflowed solder joints was investigated. The results showed that few IMCs formed at the solder/0.1 μm Au interface. Needlelike AuSn4 IMCs were observed at the solder/0.5 μm Au interface.In Sn-2.0Ag-0.75Cu-3.0Bi and Sn-3.5Ag-O.75Cu solder joints, when the laser input energy was increased, AuSn4 IMCs changed from a layer to needlelike or dendritic distribution at the solder/0.9 μm Au interface. As for the solder joints with 4.0 μm thickness of Au surface finish on pads, AuSn4 , AuSn2, AuSn IMCs, and Au2 Sn phases formed at the interface. Moreover, the content of AuSnx IMCs, such as, AuSn4 and AuSn2, which contained high Sn concentration, would become larger as the laser input energy increased. In the Sn-37Pb solder joints with 0.9 μm or 4.0 μm thickness of the Au surface finish on pads, AuSn4 IMCs were in netlike distribution. The interspaces between them were filled with Pb-rich phases.

  12. Influence of nanoparticle addition on the formation and growth of intermetallic compounds (IMCs) in Cu/Sn-Ag-Cu/Cu solder joint during different thermal conditions

    Science.gov (United States)

    Tan, Ai Ting; Tan, Ai Wen; Yusof, Farazila

    2015-06-01

    Nanocomposite lead-free solders are gaining prominence as replacements for conventional lead-free solders such as Sn-Ag-Cu solder in the electronic packaging industry. They are fabricated by adding nanoparticles such as metallic and ceramic particles into conventional lead-free solder. It is reported that the addition of such nanoparticles could strengthen the solder matrix, refine the intermetallic compounds (IMCs) formed and suppress the growth of IMCs when the joint is subjected to different thermal conditions such as thermal aging and thermal cycling. In this paper, we first review the fundamental studies on the formation and growth of IMCs in lead-free solder joints. Subsequently, we discuss the effect of the addition of nanoparticles on IMC formation and their growth under several thermal conditions. Finally, an outlook on the future growth of research in the fabrication of nanocomposite solder is provided.

  13. Inhibition of the formation of intermetallic compounds in aluminum-steel welded joints by friction stir welding; Inhibicion de la formacion de compuestos intermetalicos en juntas aluminio-acero soldadas por friccion-agitacion

    Energy Technology Data Exchange (ETDEWEB)

    Torres Lopez, E. A.; Ramirez, A. J.

    2015-07-01

    Formation of deleterious phases during welding of aluminum and steel is a challenge of the welding processes, for decades. Friction Stir Welding (FSW) has been used in an attempt to reduce formation of intermetallic compounds trough reducing the heat input. In this research, dissimilar joint of 6063-T5 aluminum alloy and AISI-SAE 1020 steel were welded using this technique. The temperature of welded joints was measured during the process. The interface of the welded joints was characterized using optical microscopy, scanning and transmission electron microscopy. Additionally, composition measurements were carried out by X-EDS and DRX. The experimental results revealed that the maximum temperature on the joint studied is less than 360 degree centigrade. The microstructural characterization in the aluminum-steel interface showed the absence of intermetallic compounds, which is a condition attributed to the use of welding with low thermal input parameters. (Author)

  14. Aversion and attraction to harmful plant secondary compounds jointly shape the foraging ecology of a specialist herbivore.

    Science.gov (United States)

    Humphrey, Parris T; Gloss, Andrew D; Alexandre, Nicolas M; Villalobos, Martha M; Fremgen, Marcella R; Groen, Simon C; Meihls, Lisa N; Jander, Georg; Whiteman, Noah K

    2016-05-01

    Most herbivorous insect species are restricted to a narrow taxonomic range of host plant species. Herbivore species that feed on mustard plants and their relatives in the Brassicales have evolved highly efficient detoxification mechanisms that actually prevent toxic mustard oils from forming in the bodies of the animals. However, these mechanisms likely were not present during the initial stages of specialization on mustard plants ~100 million years ago. The herbivorous fly Scaptomyza nigrita (Drosophilidae) is a specialist on a single mustard species, bittercress (Cardamine cordifolia; Brassicaceae) and is in a fly lineage that evolved to feed on mustards only in the past 10-20 million years. In contrast to many mustard specialists, S. nigrita does not prevent formation of toxic breakdown products (mustard oils) arising from glucosinolates (GLS), the primary defensive compounds in mustard plants. Therefore, it is an appealing model for dissecting the early stages of host specialization. Because mustard oils actually form in the bodies of S. nigrita, we hypothesized that in lieu of a specialized detoxification mechanism, S. nigrita may mitigate exposure to high GLS levels within plant tissues using behavioral avoidance. Here, we report that jasmonic acid (JA) treatment increased GLS biosynthesis in bittercress, repelled adult female flies, and reduced larval growth. S. nigrita larval damage also induced foliar GLS, especially in apical leaves, which correspondingly displayed the least S. nigrita damage in controlled feeding trials and field surveys. Paradoxically, flies preferred to feed and oviposit on GLS-producing Arabidopsis thaliana despite larvae performing worse in these plants versus non-GLS-producing mutants. GLS may be feeding cues for S. nigrita despite their deterrent and defensive properties, which underscores the diverse relationship a mustard specialist has with its host when lacking a specialized means of mustard oil detoxification. PMID

  15. Controlling Interfacial Reactions and Intermetallic Compound Growth at the Interface of a Lead-free Solder Joint with Layer-by-Layer Transferred Graphene.

    Science.gov (United States)

    Ko, Yong-Ho; Lee, Jong-Dae; Yoon, Taeshik; Lee, Chang-Woo; Kim, Taek-Soo

    2016-03-01

    The immoderate growth of intermetallic compounds (IMCs) formed at the interface of a solder metal and the substrate during soldering can degrade the mechanical properties and reliability of a solder joint in electronic packaging. Therefore, it is critical to control IMC growth at the solder joints between the solder and the substrate. In this study, we investigated the control of interfacial reactions and IMC growth by the layer-by-layer transfer of graphene during the reflow process at the interface between Sn-3.0Ag-0.5Cu (in wt %) lead-free solder and Cu. As the number of graphene layers transferred onto the surface of the Cu substrate increased, the thickness of the total IMC (Cu6Sn5 and Cu3Sn) layer decreased. After 10 repetitions of the reflow process for 50 s above 217 °C, the melting temperature of Sn-3.0Ag-0.5Cu, with a peak temperature of 250 °C, the increase in thickness of the total IMC layer at the interface with multiple layers of graphene was decreased by more than 20% compared to that at the interface of bare Cu without graphene. Furthermore, the average diameter of the Cu6Sn5 scallops at the interface with multiple layers of graphene was smaller than that at the interface without graphene. Despite 10 repetitions of the reflow process, the growth of Cu3Sn at the interface with multiple layers of graphene was suppressed by more than 20% compared with that at the interface without graphene. The multiple layers of graphene at the interface between the solder metal and the Cu substrate hindered the diffusion of Cu atoms from the Cu substrate and suppressed the reactions between Cu and Sn in the solder. Thus, the multiple layers of graphene transferred at the interface between dissimilar metals can control the interfacial reaction and IMC growth occurring at the joining interface. PMID:26856638

  16. Joint swelling

    Science.gov (United States)

    Swelling of a joint ... Joint swelling may occur along with joint pain . The swelling may cause the joint to appear larger or abnormally shaped. Joint swelling can cause pain or stiffness. After an ...

  17. Joint ventures

    DEFF Research Database (Denmark)

    Sørensen, Karsten Engsig

    Afhandlingen analysere de konkurrenceretlige og selskabsretlige regler som er bestemmende for hvordan et joint venture samarbejde er struktureret......Afhandlingen analysere de konkurrenceretlige og selskabsretlige regler som er bestemmende for hvordan et joint venture samarbejde er struktureret...

  18. Joint Disorders

    Science.gov (United States)

    A joint is where two or more bones come together, like the knee, hip, elbow, or shoulder. Joints can be damaged by many types of injuries or diseases, including Arthritis - inflammation of a joint. It causes pain, stiffness, and swelling. Over time, ...

  19. Coracoclavicular joint

    International Nuclear Information System (INIS)

    The coracoclvicular joint, a rear abnormality which may be the cause of pain in the shoulder and limitation of motion of the shoulder joint, is discussed. A case of coracoclvicular joint with shoulder pain was observed in 65 yrs old Korean male

  20. 复方甘草酸苷片联合米诺地尔溶液治疗斑秃疗效观察%Compound glycyrrhizic acid joint of minoxidil topical solution treatment bald spot observe clinical curative effect

    Institute of Scientific and Technical Information of China (English)

    俞莺; 袁波

    2012-01-01

    Objective To observe the compound glycyrrhizic acid joint of minoxidil with those minoxidil treatment bald spot curative effect controls. Methods 104 patients were randomly divided into the bald spot with the control group, the control group use minoxidil, based on the experimental group in the control group add compound glycyrrhizic acid piece of treatment. Results the recovery rate and efficient were significantly higher than those in control group (P< 0.01). Conclusion Compound glycyrrhizic acid treatment bald spot effective and safe.%目的:观察复方甘草酸苷片联合米诺地尔与单用米诺地尔治疗斑秃的疗效.方法:将104例斑秃患者随机分为治疗组与对照组:对照组单用米诺地尔,治疗组在对照组基础上加用复方甘草酸苷片治疗.结果:治疗组痊愈率与有效率均显著高于对照组(P<0.01).结论:复方甘草酸苷片联合米诺地尔治疗斑秃安全、有效,可推广应用.

  1. Transition joint

    International Nuclear Information System (INIS)

    A transition joint is disclosed for joining together tubular pieces formed respectively from a low alloy or carbon steel and a high temperature alloy composition having substantially different characteristics such as coefficient of thermal expansion, the transition joint including a plurality of tubular parts interconnected with each other by means of friction weld joints formed at an angle of 900 to the axis of the transition joint, the tubular parts at opposite ends of the transition joint being selected to facilitate in situ welding to the low alloy or carbon steel and high temperature alloy respectively. This friction welded transition joint can be used whenever different tubular pieces need to be joined together so that the joint can withstand high temperatures, for instance in heat exchangers and the such like. (Auth.)

  2. Joint pain

    Science.gov (United States)

    ... or conditions. It may be linked to arthritis , bursitis , and muscle pain . No matter what causes it, ... Autoimmune diseases such as rheumatoid arthritis and lupus Bursitis Chondromalacia patellae Crystals in the joint: gout (especially ...

  3. Intermetallic compound formation in Sn-Co-Cu, Sn-Ag-Cu and eutectic Sn-Cu solder joints on electroless Ni(P) immersion Au surface finish after reflow soldering

    International Nuclear Information System (INIS)

    The interfacial reactions between Sn-0.4Co-0.7Cu eutectic alloy and immersion Au/electroless Ni(P)/Cu substrate were investigated after reflow soldering at 260 deg. C for 2 min. Common Sn-4.0Ag-0.5Cu and eutectic Sn-0.7Cu solders were used as reference. Two types of intermetallic compounds (IMC) were found in the solder matrix of the Sn-0.4Co-0.7Cu alloy, namely coarser CoSn2 and finer Cu6Sn5 particles, while only one ternary (Cu, Ni)6Sn5 interfacial compound was detected between the solder alloy and the electroless nickel and immersion gold (ENIG) coated substrate. The same trend was also observed for the Sn-Ag-Cu and Sn-Cu solder joints. Compared with the CoSn2 particles found in the Sn-Co-Cu solder and the Ag3Sn particles found in the Sn-Ag-Cu solder, the Cu6Sn5 particles found in both solder systems exhibited finer structure and more uniform distribution. It was noted that the thickness of the interfacial IMCs for the Sn-Co-Cu, Sn-Ag-Cu and Sn-Cu alloys was 3.5 μm, 4.3 μm and 4.1 μm, respectively, as a result of longer reflow time above the alloy's melting temperature since the Sn-Ag-Cu solder alloy has the lowest melting point

  4. Intermetallic compound formation in Sn-Co-Cu, Sn-Ag-Cu and eutectic Sn-Cu solder joints on electroless Ni(P) immersion Au surface finish after reflow soldering

    Energy Technology Data Exchange (ETDEWEB)

    Sun Peng [Key State Lab for New Displays and System Integration (Chinese Ministry of Education), SMIT Center, Shanghai University, 200072 Shanghai (China) and Department of Microtechnology and Nanoscience, SMIT Center, Chalmers University of Technology, 412-96 Goeteborg (Sweden)]. E-mail: peng.sun@mc2.chalmers.se; Andersson, Cristina [Department of Microtechnology and Nanoscience, SMIT Center, Chalmers University of Technology, 412-96 Goeteborg (Sweden); Wei Xicheng [Key State Lab for New Displays and System Integration (Chinese Ministry of Education), SMIT Center, Shanghai University, 200072 Shanghai (China); Cheng Zhaonian [Department of Microtechnology and Nanoscience, SMIT Center, Chalmers University of Technology, 412-96 Goeteborg (Sweden); Shangguan Dongkai [Flextronics International, San Jose, CA (United States); Liu Johan [Key State Lab for New Displays and System Integration (Chinese Ministry of Education), SMIT Center, Shanghai University, 200072 Shanghai (China); Department of Microtechnology and Nanoscience, SMIT Center, Chalmers University of Technology, 412-96 Goeteborg (Sweden)

    2006-11-25

    The interfacial reactions between Sn-0.4Co-0.7Cu eutectic alloy and immersion Au/electroless Ni(P)/Cu substrate were investigated after reflow soldering at 260 deg. C for 2 min. Common Sn-4.0Ag-0.5Cu and eutectic Sn-0.7Cu solders were used as reference. Two types of intermetallic compounds (IMC) were found in the solder matrix of the Sn-0.4Co-0.7Cu alloy, namely coarser CoSn{sub 2} and finer Cu{sub 6}Sn{sub 5} particles, while only one ternary (Cu, Ni){sub 6}Sn{sub 5} interfacial compound was detected between the solder alloy and the electroless nickel and immersion gold (ENIG) coated substrate. The same trend was also observed for the Sn-Ag-Cu and Sn-Cu solder joints. Compared with the CoSn{sub 2} particles found in the Sn-Co-Cu solder and the Ag{sub 3}Sn particles found in the Sn-Ag-Cu solder, the Cu{sub 6}Sn{sub 5} particles found in both solder systems exhibited finer structure and more uniform distribution. It was noted that the thickness of the interfacial IMCs for the Sn-Co-Cu, Sn-Ag-Cu and Sn-Cu alloys was 3.5 {mu}m, 4.3 {mu}m and 4.1 {mu}m, respectively, as a result of longer reflow time above the alloy's melting temperature since the Sn-Ag-Cu solder alloy has the lowest melting point.

  5. Joint imaging

    International Nuclear Information System (INIS)

    Joint imaging is a proven diagnostic procedure which has become indispensable to the detection and treatment of different joint diseases in almost all disciplines. The method is suited for early diagnosis of joint affections both in soft tissue and bone which cannot be detected by X-ray or other procedures. The local activity accumulation depends on the rate of metabolism and is visualized in the scan, which in turn enables the extension and floridity of focal lesions to be evaluated and followed-up. Although joint scans may often give hints to probabilities relevant to differential diagnosis, the method is non-specific and only useful if based on the underlying clinical picture and X-ray finding, if possible. The radiation exposure is very low and does not represent a hazard in cases of adequate assessment of indication. In pregnant women and children the assessment of indication has to be based on very strict principles. The method is suited for out-patient diagnosis and can be applied in all installations equipped with a gamma camera and a technetium generator. (orig.)

  6. Joint purpose?

    DEFF Research Database (Denmark)

    Pristed Nielsen, Helene

    2013-01-01

    Starting from Crenshaw´s point that antiracism often fails to interrogate patriarchy and that feminism often reproduces racist practices (1991: 1252), this paper asks: What are the theoretical reasons for believing that feminism and anti-racism can be regarded as fighting for the joint purpose of...... anti-discrimination in Europe today? And what empirical evidence may be found for such a joint approach? The paper discusses how the contemporary EU context differs from the American context which prompted Crenshaw to raise the point about intersectionality, and it analyses documents and interviews...... from each of the two European umbrella organisations the European Women´s Lobby and the European Network against Racism, as well as a number of their national member organisations from across Europe, both within EU and non-EU member states....

  7. Diffusion bondability and joint properties of [gamma]-TiAl. Part 1. ; Diffusion bonding of intermetallic compound TiAl. Kinzokukan kagobutsu [gamma]-TiAl no kakusan setsugosei to tsugite kyodo. 1. ; TiAl no kakusan setsugo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Nakao, Y.; Shinozaki, K. (Osaka Univ., Osaka (Japan). Faculty of Engineering); Hamada, M. (Osaka Univ., Osaka (Japan). Graduate School)

    1993-11-05

    Since Ni3Al, which has been characterized as brittle, has been clarified that it would have an extremely excellent ductility by adding B, the intermetallic compound has been being paid attention as the high temperature structural and heat resisting material, which might be closer to the practical application compared with the ceramics. On the other hand, it is thought to be indispensable, that the welding and jointing technology should be established for the practical application of the structural material. Accordingly in this study, for the purpose of establishing the bonding technology of TiAl, by using the Ti-38% mass% Al casting, and then by bonding TiAl each other through using the solid phase diffusion bonding, the selection of the proper bonding condition, bonding phenomena and mechanical properties have been investigated. Under the bonding condition, in which the void coefficient and oxide occupancy ratio have come to be below 1%, for the bonding joints selected the bonding temperature of 1473K, bonding time of 3.84ks, bonding pressure of 15MPa and bonding atmosphere of 26mPa, the tensile tests at 1073 and 1273K of the room temperature have been executed. As a consequence, the joint tensile strength has been dropped by 45 and 40MPa respectively compared with those of the base metal, and moreover all of the joints have been fractured at the bonding interfaces. 27 refs., 16 figs., 1 tab.

  8. Knee joint replacement

    Science.gov (United States)

    Knee joint replacement is a surgery to replace a knee joint with a man-made joint. The artificial joint is called a prosthesis . ... cartilage and bone are removed from the knee joint. Man-made pieces are then placed in the ...

  9. Reliability of Tubular Joints

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Thoft-Christensen, Palle

    In this paper the preliminary results obtained by tests on tubular joints are presented. The joints are T-joints and the loading is static. It is the intention in continuation of these tests to perform tests on other types of joints (e.g. Y-joints) and also with dynamic loading. The purpose of th...

  10. Joint Replacement Surgery

    Science.gov (United States)

    ... a Clinical Trial Journal Articles Arthritis July 2014 Joint Replacement Surgery: Health Information Basics for You and Your Family What Is Joint Replacement Surgery? Joint replacement surgery is removing a ...

  11. Joint x-ray

    Science.gov (United States)

    X-ray - joint; Arthrography; Arthrogram ... x-ray technologist will help you position the joint to be x-rayed on the table. Once in place, pictures are taken. The joint may be moved into other positions for more ...

  12. Joint instability and osteoarthritis.

    Science.gov (United States)

    Blalock, Darryl; Miller, Andrew; Tilley, Michael; Wang, Jinxi

    2015-01-01

    Joint instability creates a clinical and economic burden in the health care system. Injuries and disorders that directly damage the joint structure or lead to joint instability are highly associated with osteoarthritis (OA). Thus, understanding the physiology of joint stability and the mechanisms of joint instability-induced OA is of clinical significance. The first section of this review discusses the structure and function of major joint tissues, including periarticular muscles, which play a significant role in joint stability. Because the knee, ankle, and shoulder joints demonstrate a high incidence of ligament injury and joint instability, the second section summarizes the mechanisms of ligament injury-associated joint instability of these joints. The final section highlights the recent advances in the understanding of the mechanical and biological mechanisms of joint instability-induced OA. These advances may lead to new opportunities for clinical intervention in the prevention and early treatment of OA. PMID:25741184

  13. Spacesuit mobility knee joints

    Science.gov (United States)

    Vykukal, H. C. (Inventor)

    1979-01-01

    Pressure suit mobility joints are for use in interconnecting adjacent segments of an hermetically sealed spacesuit in which low torques, low leakage and a high degree of reliability are required. Each of the joints is a special purpose joint characterized by substantially constant volume and low torque characteristics and includes linkages which restrain the joint from longitudinal distension and includes a flexible, substantially impermeable diaphragm of tubular configuration spanning the distance between pivotally supported annuli. The diaphragms of selected joints include rolling convolutions for balancing the joints, while various joints include wedge-shaped sections which enhance the range of motion for the joints.

  14. Joint fluid Gram stain

    Science.gov (United States)

    Gram stain of joint fluid ... A sample of joint fluid is needed. The fluid sample is sent to a lab where a small drop is placed in a ... on how to prepare for the removal of joint fluid, see joint fluid aspiration .

  15. Butt Joint Tool Commissioning

    Energy Technology Data Exchange (ETDEWEB)

    Martovetsky, N N

    2007-12-06

    ITER Central Solenoid uses butt joints for connecting the pancakes in the CS module. The principles of the butt joining of the CICC were developed by the JAPT during CSMC project. The difference between the CSMC butt joint and the CS butt joint is that the CS butt joint is an in-line joint, while the CSMC is a double joint through a hairpin jumper. The CS butt joint has to carry the hoop load. The straight length of the joint is only 320 mm, and the vacuum chamber around the joint has to have a split in the clamp shell. These requirements are challenging. Fig.1 presents a CSMC joint, and Fig.2 shows a CS butt joint. The butt joint procedure was verified and demonstrated. The tool is capable of achieving all specified parameters. The vacuum in the end was a little higher than the target, which is not critical and readily correctable. We consider, tentatively that the procedure is established. Unexpectedly, we discover significant temperature nonuniformity in the joint cross section, which is not formally a violation of the specs, but is a point of concern. All testing parameters are recorded for QA purposes. We plan to modify the butt joining tool to improve its convenience of operation and provide all features necessary for production of butt joints by qualified personnel.

  16. Culture - joint fluid

    Science.gov (United States)

    Joint fluid culture ... fungi, or viruses grow. This is called a culture. If these germs are detected, other tests may ... is no special preparation needed for the lab culture. How to prepare for the removal of joint ...

  17. Temporomandibular Joint Dysfunction

    Science.gov (United States)

    The temporomandibular joint (TMJ) connects your jaw to the side of your head. When it works well, it enables you to ... For people with TMJ dysfunction, problems with the joint and muscles around it may cause Pain that ...

  18. Knee joint replacement - slideshow

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/presentations/100088.htm Knee joint replacement - series To use the sharing features ... 4 out of 4 Normal anatomy Overview The knee is a complex joint. It contains the distal ...

  19. Shoulder Joint Replacement

    Science.gov (United States)

    ... en because of implant loosening, wear, infection, and dislocation. When this occurs, a second joint replacement surgery — called a revision surgery — may be necessary. Is Shoulder Joint Replacement for You? The decision to have ...

  20. International joint ventures

    DEFF Research Database (Denmark)

    Sørensen, Karsten Engsig

    2001-01-01

    The article analysis problems connected with corporate joint ventures. Among others the possible conflicts between the joint venture agreement and the statutes of the companies is examined, as well as certain problems connected to the fact that the joint venture partners have created commen control...

  1. 盐酸舍曲林联合复方玄驹胶囊并配合早泄训练治疗早泄的临床疗效%Effect of joint compound XuanJu sertraline hydrochloride capsules and premature ejaculation training for the treatment of premature ejaculation

    Institute of Scientific and Technical Information of China (English)

    方卫; 胡恩宜

    2015-01-01

    目的:观察盐酸舍曲林、复方玄驹胶囊配合早泄训练疗法治疗早泄的临床疗效。方法:将55例符合诊断标准的早泄患者给予盐酸舍曲林联合复方玄驹胶囊口服治疗,同时进行早泄训练,疗程为1个月,治疗前后进行 CIPE、IELT 和双方性满意度的评估,并进行统计学分析。结果:实际治疗了50例,脱落5例,在 CIPE 评分、IELT 评分、双方的性生活满意度评分中,治疗前后比较,P <0.01,差异均有统计学意义。结论:盐酸舍曲林联合复方玄驹胶囊治疗并配合早泄训练能明显改善早泄患者的性生活质量。%Objectives:To explore the clinical curative effect of sertraline hydrochloride compound XuanJu capsule and premature ejaculation training in treating premature ejaculation.Methods:55 patients whose diagnoses were standard premature ejaculation were given joint compound XuanJu sertraline hydrochloride capsule orally,as well as premature ejaculation training at the same time for 1 month.The CIPE,IELT and sexual satisfaction both before and after treatment were evaluated and statistical analysis was conducted.Results:50 cases were successfully treated and 5 cases failed.In terms of CIPE,IELT score and the sexual satisfaction ratings,statistically significant difference between before and after treatment was found,P <0.01.Conclusion:Joint compound XuanJu sertraline hydrochloride capsules and premature ejaculation training can significantly improve the sex life quality of patients with premature ejaculation.

  2. Managing Joint Production Motivation

    DEFF Research Database (Denmark)

    Lindenberg, Siegwart; Foss, Nicolai Juul

    2011-01-01

    We contribute to the microfoundations of organizational performance by proffering the construct of joint production motivation. Under such motivational conditions individuals see themselves as part of a joint endeavor, each with his or her own roles and responsibilities; generate shared represent......We contribute to the microfoundations of organizational performance by proffering the construct of joint production motivation. Under such motivational conditions individuals see themselves as part of a joint endeavor, each with his or her own roles and responsibilities; generate shared...... representations of actions and tasks; cognitively coordinate cooperation; and choose their own behaviors in terms of joint goals. Using goal-framing theory, we explain how motivation for joint production can be managed by cognitive/symbolic management and organizational design....

  3. RILEM International Symposium on Materials and Joints in Timber Structures

    CERN Document Server

    Reinhardt, H-W; Garrecht, Harald

    2014-01-01

    This book contains the contributions from the RILEM International Symposium on Materials and Joints in Timber Structures that was held in Stuttgart, Germany from October 8 to 10, 2013. It covers recent developments in the materials and the joints used in modern timber structures. Regarding basic wooden materials, the contributions highlight the widened spectrum of products comprising cross-laminated timber, glulam and LVL from hardwoods and block glued elements. Timber concrete compounds, cement bonded wood composites and innovative light-weight constructions represent increasingly employed alternatives for floors, bridges and facades. With regard to jointing technologies, considerable advances in both mechanical connections and glued joints are presented. Self-tapping screws have created unprecedented options for reliable, strong as well as ductile joints and reinforcement technologies. Regarding adhesives, which constitute the basis of the jointing/laminating technology of modern timber products, extended o...

  4. Sacroiliac joint pain - aftercare

    Science.gov (United States)

    The sacroiliac joint (SIJ) is a term used to describe the place where the sacrum and the iliac bones join. The ... The main purpose of the joint is to connect the spine and the pelvis. As a result, there is very little movement at the SIJ. Major reasons ...

  5. JET Joint Undertaking

    International Nuclear Information System (INIS)

    The paper presents the progress report of the Joint European Torus (JET) Joint Undertaking, 1986. The report contains a survey of the scientific and technical achievements on JET during 1986; the more important articles referred to in this survey are reproduced as appendices to this Report. The last section discusses developments which might improve the overall performance of the machine. (U.K.)

  6. "Nonfloating" universal joint

    Science.gov (United States)

    Appleberry, W. T.

    1978-01-01

    Modified crowned-spline joint is lightweight, durable, and requires minimum of parts. It does not use rubber cushions to limit play and is useful over wide temperature range. It has inner ball and socket to provide rigid connection with no axial play. Joint can be adapted to form pinned connection between segmented torque tubes.

  7. MR diagnosis of temporomandibular joint. A study of joint effusion

    Energy Technology Data Exchange (ETDEWEB)

    Kaneda, Takashi; Yamashiro, Mitsuaki; Ozawa, Kaoru; Suzuki, Hiromi; Okada, Hiroyuki; Yamamoto, Hirotsugu [Nihon Univ., Matsudo, Chiba (Japan). School of Dentistry

    1998-03-01

    The purposes of this study were to evaluate the relationship between correlation of MR joint effusion of the temporomandibular joint and disk position, to evaluate the relationship between joint effusion and aging, and to assess the frequency of MR joint effusion of bilateral temporomandibular joints. The temporomandibular joints of 192 patients with clinical symptoms of temporomandibular joint disorders were imaged bilaterally using high field, surface-coil MR imaging. Oblique sagittal and coronal proton density-weighted and T2-weighted images were obtained. Imaging findings of joint effusion were correlated with disk position, aging, and bilateral temporomandibular joints. MR showed effusion in 4% of the joints with normal superior disk position, 36% of the joints with disk displacement with reduction, and 45% of the joints with disk displacement without reduction. There were significant differences in the incidence of joint effusion between normal disk position and anterior disk displacement with or without reduction. Younger patients less than 40 years were significant higher the incidence of joint effusion than those of older patients. A significant association was seen between joint effusion and aging. MR showed effusion in 17% of the unilateral temporomandibular joint, 24% of the bilateral temporomandibular joints. There was no significant difference between unilateral and bilateral case. These results indicated that joint effusion using MR imaging was associated with varied temporomandibular joint pathologic states. (author)

  8. MR diagnosis of temporomandibular joint. A study of joint effusion

    International Nuclear Information System (INIS)

    The purposes of this study were to evaluate the relationship between correlation of MR joint effusion of the temporomandibular joint and disk position, to evaluate the relationship between joint effusion and aging, and to assess the frequency of MR joint effusion of bilateral temporomandibular joints. The temporomandibular joints of 192 patients with clinical symptoms of temporomandibular joint disorders were imaged bilaterally using high field, surface-coil MR imaging. Oblique sagittal and coronal proton density-weighted and T2-weighted images were obtained. Imaging findings of joint effusion were correlated with disk position, aging, and bilateral temporomandibular joints. MR showed effusion in 4% of the joints with normal superior disk position, 36% of the joints with disk displacement with reduction, and 45% of the joints with disk displacement without reduction. There were significant differences in the incidence of joint effusion between normal disk position and anterior disk displacement with or without reduction. Younger patients less than 40 years were significant higher the incidence of joint effusion than those of older patients. A significant association was seen between joint effusion and aging. MR showed effusion in 17% of the unilateral temporomandibular joint, 24% of the bilateral temporomandibular joints. There was no significant difference between unilateral and bilateral case. These results indicated that joint effusion using MR imaging was associated with varied temporomandibular joint pathologic states. (author)

  9. Light metal compound casting

    Institute of Scientific and Technical Information of China (English)

    Konrad; J.; M.; PAPIS; Joerg; F.; LOEFFLER; Peter; J.; UGGOWITZER

    2009-01-01

    Compound casting’simplifies joining processes by directly casting a metallic melt onto a solid metal substrate. A continuously metallurgic transition is very important for industrial applications, such as joint structures of spaceframe constructions in transport industry. In this project, ‘compound casting’ of light metals is investigated, aiming at weight-saving. The substrate used is a wrought aluminium alloy of type AA5xxx, containing magnesium as main alloying element. The melts are aluminium alloys, containing various alloying elements (Cu, Si, Zn), and magnesium. By replacing the natural oxygen layer with a zinc layer, the inherent wetting difficulties were avoided, and compounds with flawless interfaces were successfully produced (no contraction defects, cracks or oxides). Electron microscopy and EDX investigations as well as optical micrographs of the interfacial areas revealed their continu- ously metallic constitution. Diffusion of alloying elements leads to heat-treatable microstructures in the vicinity of the joining interfaces in Al-Al couples. This permits significant variability of mechanical properties. Without significantly cutting down on wettability, the formation of low-melting intermetallic phases (Al3Mg2 and Al12Mg17 IMPs) at the interface of Al-Mg couples was avoided by applying a protective coating to the substrate.

  10. Light metal compound casting

    Institute of Scientific and Technical Information of China (English)

    Konrad J.M.PAPIS; Joerg F.LOEFFLER; Peter J.UGGOWITZER

    2009-01-01

    'Compound casting'simplifies joining processes by directly casting a metallic melt onto a solid metal substrate. A continuously metallurgic transition is very important for industrial applications, such as joint structures of spaceframe constructions in transport industry. In this project, 'compound casting' of light metals is investigated, aiming at weight-saving. The substrate used is a wrought aluminium alloy of type AA5xxx, containing magnesium as main alloying element. The melts are aluminium alloys, containing various alloying elements (Cu, Si, Zn), and magnesium. By replacing the natural oxygen layer with a zinc layer, the inherent wetting difficulties were avoided, and compounds with flawless interfaces were successfully produced (no contraction defects, cracks or oxides). Electron microscopy and EDX investigations as well as optical micrographs of the interfacial areas revealed their continu-ously metallic constitution. Diffusion of alloying elements leads to heat-treatable microstructures in the vicinity of the joining interfaces in Al-Al couples. This permits significant variability of mechanical properties. Without significantly cutting down on wettability, the formation of low-melting intermetallic phases (Al3Mg2 and AI12Mg17 IMPs) at the interface of Al-Mg couples was avoided by applying a protec-tive coating to the substrate.

  11. Multipurpose Compound

    Science.gov (United States)

    1983-01-01

    Specially formulated derivatives of an unusual basic compound known as Alcide may be the answer to effective treatment and prevention of the disease bovine mastitis, a bacterial inflammation of a cow's mammary gland that results in loss of milk production and in extreme cases, death. Manufactured by Alcide Corporation the Alcide compound has killed all tested bacteria, virus and fungi, shortly after contact, with minimal toxic effects on humans or animals. Alcide Corporation credits the existence of the mastitis treatment/prevention products to assistance provided the company by NERAC, Inc.

  12. Joint Quantum Institute

    Data.gov (United States)

    Federal Laboratory Consortium — The Joint Quantum Institute (JQI) is pursuing that goal through the work of leading quantum scientists from the Department of Physics of the University of Maryland...

  13. Joint Injection/Aspiration

    Science.gov (United States)

    ... Working It Out: Common Techniques for Conflict Resolution Workplace Diversity & Team Performance CME & MOC Understanding MOC ACR's MOC ... infection is suspected, aspirating the joint to gather cultures is ... Communications and Marketing. This patient information is provided for ...

  14. MP Joint Arthritis

    Science.gov (United States)

    ... Therapist? Media Find a Hand Surgeon MP Joint Arthritis Email to a friend * required fields From * To * ... in to name and customize your collection. DESCRIPTION Arthritis is the wearing away of the cartilage at ...

  15. Hip joint replacement

    Science.gov (United States)

    ... may have problems with infection, loosening, or even dislocation of the new hip joint. Over time the artificial ... Professor, Chief, Sports Medicine and Shoulder Service, UCSF Department of Orthopaedic Surgery, San Francisco, ...

  16. Temporomandibular Joint Disorder

    Science.gov (United States)

    ... 2008 Previous Next Related Articles: Temporomandibular Joint Disorder (TMD) Are You Biting Off More Than You Can Chew? Equilibration May Lessen TMD Pain Fender-benders: Source of TMD? First Comes ...

  17. Healthy Joints Matter

    Science.gov (United States)

    ... dietary supplements, such as green tea and various vitamins, to see if they can keep your joints ... body, such as your ears, nose, and windpipe. Fibromyalgia (fi-bro-my-AL-juh). A condition that ...

  18. Compound odontoma

    Directory of Open Access Journals (Sweden)

    Monica Yadav

    2012-01-01

    Full Text Available Odontomas have been extensively reported in the dental literature, and the term refers to tumors of odontogenic origin. Though the exact etiology is still unknown, the postulated causes include: local trauma, infection, inheritance and genetic mutation. The majority of the lesions are asymptomatic; however, may be accompanied with pain and swelling as secondary complaints in some cases. Here, we report a case of a compound odontome in a 14 year old patient.

  19. Magnesium compounds

    Science.gov (United States)

    Kramer, D.A.

    2006-01-01

    In 2005, seawater and natural brines accounted for 51% of US magnesium compounds production. World magnesia production was estimated to be 14.5 Mt. Most of the production came from China, North Korea, Russia and Turkey. Although no specific production figures are available, Japan and the United States are estimated to account for almost one-half of the world's capacity from seawater and brines.

  20. Joint contingency contracting

    OpenAIRE

    Johnson, Ellsworth K.; Paton, Bryan H.; Threat, Edward W.; Haptonstall, Lisa A.

    2005-01-01

    The purpose of this Master of Business Administration (MBA) Professional Report is to investigate and analyze the means by which Contingency Contracting Officers (CCO) can effectively operate in a Joint contingency environment and to validate the Defense Contract Management Agency's (DCMA) entry and exit criteria for contingency contracting missions. Joint contingencies encompass regional conflicts, humanitarian and peacekeeping missions, and international or domestic disaster relief missions...

  1. Joint Aspiration: Arthrocentesis

    OpenAIRE

    Mackie, John William

    1987-01-01

    Joint aspiration is an easily mastered procedure used to confirm or rule out joint sepsis and crystal-induced arthrosis. It is routinely performed with or without local anaesthetic, or with cooling spray. The time spent obtaining the fluid is short. The procedure is safe, requiring no hospitalization, except in the case of diagnosed sepsis. Arthrocentesis is a necessary procedure to prove beyond reasonable doubt that infection is not the cause of the arthritis. The family physician must be fa...

  2. Joint Venture Contracts

    OpenAIRE

    Pimentel, Dinarco

    2015-01-01

    Joint Venture contracts are contracting models typically designed to reach international markets. In spite of being used at the national level, a joint venture is based on single or multiple contracts between two individuals, two institutions, two organizations or two different entrepreneurial entities joining forces, meeting synergies to reach a common goal.Initially, these types of contracts were justifiable based on the need of different economic agents penetrating the most inaccessible ma...

  3. A symptomatic coracoclavicular joint.

    Science.gov (United States)

    Cheung, T F S; Boerboom, A L; Wolf, R F E; Diercks, R L

    2006-11-01

    Bilateral coracoclavicular joints were found in a 44-year-old male patient following a fall. He had an Indonesian mother and a Dutch father. Prior to the injury he was asymptomatic and had full range of movement in both shoulders but the trauma resulted in pain and limitation of movement in the left shoulder which required resection of the anomalous joint, after which full pain-free movement was restored. PMID:17075101

  4. Seabrook Station service water piping refurbishment using the joint seal method

    International Nuclear Information System (INIS)

    The Seabrook Station service water system is fabricated from butt welded, cement lined, carbon steel piping. The service water system fluid is sea water from the Atlantic Ocean and/or potable water from a backup evaporative cooling tower. Joint compound was applied at field welds to seal cement liner crevices. Inspections of 24 inch (61 cm) above ground piping during a refueling outage revealed that the joint compound was degrading in a small percentage of the weld joints. At these locations, sea water was allowed to contact the piping substrate and initiate pitting corrosion. This paper discusses the refurbishment project conducted at Seabrook Station in which Miller Pipeline Corp. AMEX-10/WEKO Seals were installed in safety related service water piping at field weld joint cement liner crevices. This joint seal system utilizes an elastomer boot seal with 6% molybdenum stainless steel circumferential retaining bands on each side of the joint to secure the boot in place. This joint seal design provides a pressure tight seal in order to prevent further sea water intrusion into field weld joints due to degraded joint compound. Isolation of joints from the bulk oxygenated service water flow and high chlorides will arrest any current corrosion and prevent future degradation of these welded joints

  5. Anatomy and arthrokinematics of the human ankle and intertarsal joints

    International Nuclear Information System (INIS)

    In the ankle (talocrural) joint, the lower end of the tibia and fibula embrace the trochlea tali. Thus, an approximately uniaxial joint is formed which permits dorsiflexion and plantarflexion of the foot against the leg. Due to the geometry of the trochlea tali, conjunct lateral rotation of the fibula against the tibia occurs at the tibiofibular articulations synchronously with active dorsiflexion at the ankle joint. Movements at the talocrural joints are mainly limited by the opposing muscles as well as by strong collateral ligaments. Talus and calcaneus form a functional unit connected by posterior and anterior articulations. The posterior articulation is the subtalar (talocalcaneal) joint; in the anterior articulation, talar facets of the calcaneus together with the posterior surface of the navicular and the superior fibrocartilaginous surface of the plantar calcaneonavicular ligament form a concavity for the talar head. Thus, the talocalcaneonavicular joint is a compound and - like the subtalar joint - a multiaxial articulation. On the weightbearing foot, the distal tarsus and metatarsus are pronated and supinated against the talus in order to maintain plantigrade contact. When the foot is off the ground, these movements are modified to eversion and inversion, also involving the calcaneocuboid joint. In addition, movements between the calcaneus and cuboid also occur during pronative or supinative changes between the fore- and hindfoot. Limitation of movements is due to leg muscles as well as strong ligaments. Finally, the cuneonavicular, cuboideonavicular, intercuneiform and cuneocuboid joints permit some additional alterations of the loaded foot in contact with the ground. (orig.)

  6. 中药藤莓汤对Ⅱ型胶原诱导性大鼠关节炎性病理损伤的影响%Effects of the Chinese herbal compound, Tengmei decoction, on inflammatory injury in joints of rat models of type Ⅱcollagen-induced arthritis

    Institute of Scientific and Technical Information of China (English)

    陆妍; 王洁; 孟凤仙; 王亚南; 刘慧; 马卫国; 张继胜; 谭玲; 李慧慧; 林子超; 沈志明

    2015-01-01

    Objective To explore the effects of Chinese herbal compound, Tengmei decoction, on type II collagen-induced arthritis ( CIA) in rats, and to examine the changes of arthritis index ( AI) , limb swelling, joint tissue inflammatory infiltration, and the effects on immune-inflammatory factors.Methods Sprague-Dawley rat models of arthritis were successfully established by intradermal injection of type II collagen and Freund’ s complete adjuvant.The model rats were randomly divided into model group, positive drug group, and high-and low-dose Chinese medicine groups, 6 rats in each group.The intervention and treatment period was 12 weeks.To measure weekly the anteroposterior and transverse diameters of the rear ankles and wrists, the transverse diameter of the claw foot palm pad, the thickness and the highest point width of hind limb plantar joint swelling, and to evaluate the integrated scores of joints and limbs swelling using a vernier caliper.Results ①Compared with the normal group, the total arthritis scores and hind limbs AI scores of the model group were significantly increased ( P <0.05 or P <0.01 ) .The left forelimb AI scores were significantly increased during 10 -12 weeks ( P <0.05 ) .The anteroposterior and transverse diameters of the left hind limb, the thickness of the highest point measurement of the left hind foot pad metatarsal were significantly increased ( P<0.05 or P<0.01) in different time periods between 1-12 weeks.Compared with the model group, the total scores and the left hind limb joints AI scores of the high-and low-dose drug groups were decreased after 6 weeks (P<0.05).②Compared with the normal control group, levels of mRNA transcription and protein expression of IL-6 and TNF-αwere significantly up-regulated ( P<0.01 ) in the model group.Compared with the model group, the levels of mRNA transcription and the expression of IL-6 and TNF-αproteins were significantly down-regulated in the positive group and Chinese medicine groups ( P <0

  7. A microstructural analysis of solder joints from the electronic assemblies of dismantled nuclear weapons

    Energy Technology Data Exchange (ETDEWEB)

    Vianco, P.T.; Rejent, J.A. [Sandia National Labs., Albuquerque, NM (United States). Materials Joining Dept.

    1997-05-01

    MC1814 Interconnection Boxes from dismantled B57 bombs, and MC2839 firing Sets from retired W70-1 warheads were obtained from the Pantex facility. Printed circuit boards were selected from these components for microstructural analysis of their solder joints. The analysis included a qualitative examination of the solder joints and quantitative assessments of (1) the thickness of the intermetallic compound layer that formed between the solder and circuit board Cu features, and (2) the Pb-rich phase particle distribution within the solder joint microstructure. The MC2839 solder joints had very good workmanship qualities. The intermetallic compound layer stoichiometry was determined to be that of Cu6Sn5. The mean intermetallic compound layer thickness for all solder joints was 0.885 mm. The magnitude of these values did not indicate significant growth over the weapon lifetime. The size distribution of the Pb-rich phase particles for each of the joints were represented by the mean of 9.85 {times} 10{sup {minus}6} mm{sup 2}. Assuming a spherical geometry, the mean particle diameter would be 3.54 mm. The joint-to-joint difference of intermetallic compound layer thickness and Pb-rich particle size distribution was not caused by varying thermal environments, but rather, was a result of natural variations in the joint microstructure that probably existed at the time of manufacture. The microstructural evaluation of the through-hole solder joints form the MC2839 and MC1814 components indicated that the environmental conditions to which these electronic units were exposed in the stockpile, were benign regarding solder joint aging. There was an absence of thermal fatigue damage in MC2839 circuit board, through-hole solder joints. The damage to the eyelet solder joints of the MC1814 more likely represented infant mortality failures at or very near the time of manufacture, resulting from a marginal design status of this type of solder joint design.

  8. Forming a multinational joint venture

    International Nuclear Information System (INIS)

    This paper discusses the basis and mechanics for forming a multinational joint venture. The topics of the paper include the motivations for a joint venture, selection of the appropriate co-venturer, management of the multinational joint venture, and the joint venture agreement. The authors state that a joint venture is not applicable or desirable in all instances and to be successful, must be carefully planned

  9. The temporomandibular joint

    International Nuclear Information System (INIS)

    Whilst the temporomandibular joint is in many ways unique, it is subject to all the diseases and disorders found in joints in other parts of the human skeleton. By far the most common disorder is injury, followed by arthropathy, acute and chronic dislocations, ankylosis, and in rare instances, neoplasms. The diagnosis and management of the temporomandibular joint are the primary responsibility of the oral surgeon. Nevertheless, this anatomical region is an area in which the cooperation of medical and dental disciplines may be required for the satisfactory conclusion of treatment. The more so when the disease process involves either associated psychosomatic illness or malignancy. The mainstay of the diagnosis is a careful radiological examination of the joint. There exists a delicate relationship between the dentition, the muscles of mastication, and the temporomandibular articulation, which is controlled by arthrokinetic reflex activity of the branches of the 5th cranial nerve. Imbalance between one or more of the components of this integrated system frequently leads to disturbances in function. Pain-dysfunction disorders constitute the larger part of temporomandibular joint disturbances generally encountered

  10. Periprosthetic Joint Infections

    Directory of Open Access Journals (Sweden)

    Ana Lucia L. Lima

    2013-01-01

    Full Text Available Implantation of joint prostheses is becoming increasingly common, especially for the hip and knee. Infection is considered to be the most devastating of prosthesis-related complications, leading to prolonged hospitalization, repeated surgical intervention, and even definitive loss of the implant. The main risk factors to periprosthetic joint infections (PJIs are advanced age, malnutrition, obesity, diabetes mellitus, HIV infection at an advanced stage, presence of distant infectious foci, and antecedents of arthroscopy or infection in previous arthroplasty. Joint prostheses can become infected through three different routes: direct implantation, hematogenic infection, and reactivation of latent infection. Gram-positive bacteria predominate in cases of PJI, mainly Staphylococcus aureus and Staphylococcus epidermidis. PJIs present characteristic signs that can be divided into acute and chronic manifestations. The main imaging method used in diagnosing joint prosthesis infections is X-ray. Computed tomography (CT scan may assist in distinguishing between septic and aseptic loosening. Three-phase bone scintigraphy using technetium has high sensitivity, but low specificity. Positron emission tomography using fluorodeoxyglucose (FDG-PET presents very divergent results in the literature. Definitive diagnosis of infection should be made by isolating the microorganism through cultures on material obtained from joint fluid puncturing, surgical wound secretions, surgical debridement procedures, or sonication fluid. Success in treating PJI depends on extensive surgical debridement and adequate and effective antibiotic therapy. Treatment in two stages using a spacer is recommended for most chronic infections in arthroplasty cases. Treatment in a single procedure is appropriate in carefully selected cases.

  11. Distal radioulnar joint injuries.

    Science.gov (United States)

    Thomas, Binu P; Sreekanth, Raveendran

    2012-09-01

    Distal radioulnar joint is a trochoid joint relatively new in evolution. Along with proximal radioulnar joint, forearm bones and interosseous membrane, it allows pronosupination and load transmission across the wrist. Injuries around distal radioulnar joint are not uncommon, and are usually associated with distal radius fractures,fractures of the ulnar styloid and with the eponymous Galeazzi or Essex_Lopresti fractures. The injury can be purely involving the soft tissue especially the triangular fibrocartilage or the radioulnar ligaments. The patients usually present with ulnar sided wrist pain, features of instability, or restriction of rotation. Difficulty in carrying loads in the hand is a major constraint for these patients. Thorough clinical examination to localize point of tenderness and appropriate provocative tests help in diagnosis. Radiology and MRI are extremely useful, while arthroscopy is the gold standard for evaluation. The treatment protocols are continuously evolving and range from conservative, arthroscopic to open surgical methods. Isolated dislocation are uncommon. Basal fractures of the ulnar styloid tend to make the joint unstable and may require operative intervention. Chronic instability requires reconstruction of the stabilizing ligaments to avoid onset of arthritis. Prosthetic replacement in arthritis is gaining acceptance in the management of arthritis. PMID:23162140

  12. Distal radioulnar joint injuries

    Directory of Open Access Journals (Sweden)

    Binu P Thomas

    2012-01-01

    Full Text Available Distal radioulnar joint is a trochoid joint relatively new in evolution. Along with proximal radioulnar joint , forearm bones and interosseous membrane, it allows pronosupination and load transmission across the wrist. Injuries around distal radioulnar joint are not uncommon, and are usually associated with distal radius fractures,fractures of the ulnar styloid and with the eponymous Galeazzi or Essex_Lopresti fractures. The injury can be purely involving the soft tissue especially the triangular fibrocartilage or the radioulnar ligaments.The patients usually present with ulnar sided wrist pain, features of instability, or restriction of rotation. Difficulty in carrying loads in the hand is a major constraint for these patients. Thorough clinical examination to localize point of tenderness and appropriate provocative tests help in diagnosis. Radiology and MRI are extremely useful, while arthroscopy is the gold standard for evaluation. The treatment protocols are continuously evolving and range from conservative, arthroscopic to open surgical methods. Isolated dislocation are uncommon. Basal fractures of the ulnar styloid tend to make the joint unstable and may require operative intervention. Chronic instability requires reconstruction of the stabilizing ligaments to avoid onset of arthritis. Prosthetic replacement in arthritis is gaining acceptance in the management of arthritis.

  13. Intermetallic Compounds

    Science.gov (United States)

    Takagiwa, Y.; Matsuura, Y.; Kimura, K.

    2014-06-01

    We have focused on the binary narrow-bandgap intermetallic compounds FeGa3 and RuGa3 as thermoelectric materials. Their crystal structure is FeGa3-type (tetragonal, P42/ mnm) with 16 atoms per unit cell. Despite their simple crystal structure, their room temperature thermal conductivity is in the range 4-5-W-m-1-K-1. Both compounds have narrow-bandgaps of approximately 0.3-eV near the Fermi level. Because their Seebeck coefficients are quite large negative values in the range 350-thermoelectric materials both by adjusting the carrier concentration and by reducing the thermal conductivity. Here, we report the effects of doping on the thermoelectric properties of FeGa3 and RuGa3 as n and p-type materials. The dimensionless figure of merit, ZT, was significantly improved by substitution of Sn for Ga in FeGa3 (electron-doping) and by substitution of Zn for Ga in RuGa3 (hole-doping), mainly as a result of optimization of the electronic part, S 2 σ.

  14. Total ankle joint replacement.

    Science.gov (United States)

    2016-02-01

    Ankle arthritis results in a stiff and painful ankle and can be a major cause of disability. For people with end-stage ankle arthritis, arthrodesis (ankle fusion) is effective at reducing pain in the shorter term, but results in a fixed joint, and over time the loss of mobility places stress on other joints in the foot that may lead to arthritis, pain and dysfunction. Another option is to perform a total ankle joint replacement, with the aim of giving the patient a mobile and pain-free ankle. In this article we review the efficacy of this procedure, including how it compares to ankle arthrodesis, and consider the indications and complications. PMID:26868932

  15. Transversely Compressed Bonded Joints

    DEFF Research Database (Denmark)

    Hansen, Christian Skodborg; Schmidt, Jacob Wittrup; Stang, Henrik

    2012-01-01

    The load capacity of bonded joints can be increased if transverse pressure is applied at the interface. The transverse pressure is assumed to introduce a Coulomb-friction contribution to the cohesive law for the interface. Response and load capacity for a bonded single-lap joint was derived using...... non-linear fracture mechanics. The results indicated a good correlation between theory and tests. Furthermore, the model is suggested as theoretical base for determining load capacity of bonded anchorages with transverse pressure, in externally reinforced concrete structures....

  16. Expansion joints for LMFBR

    International Nuclear Information System (INIS)

    This discourse recounts efforts put into the SNR-2 project; specifically the development of compensation devices. The various prototypes of these compensation devices are described and the state of the development reviewed. Large Na (sodium)-heat transfer systems require a lot of valuable space if the component lay-out does not include compensation devices. So, in order to condense the spatial requirement as much as possible, expansion joints must be integrated into the pipe system. There are two basic types to suit the purpose: axial expansion joints and angular expansion joints. The expansion joints were developed on the basis of specific design criteria whereby differentiation is made between expansion joints of small and large nominal diameter. Expansion joints for installation in the sodium-filled primary piping are equipped with safety bellows in addition to the actual working bellows. Expansion joints must be designed and mounted in a manner to completely withstand seismic forces. The design must exclude any damage to the bellows during intermittent operations, that is, when sodium is drained the bellows' folds must be completely empty; otherwise residual solidified sodium could destroy the bellows when restarting. The expansion joints must be engineered on the basis of the following design data for the secondary system of the SNR project: working pressure: 16 bar; failure mode pressure: 5 events; failure mode: 5 sec., 28.5 bar, 520 deg. C; working temperature: 520 deg. C; temperature transients: 30 deg. C/sec.; service life: 200,000 h; number of load cycles: 104; material: 1.4948 or 1.4919; layer thickness of folds: 0.5 mm; angular deflection (DN 800): +3 deg. C or; axial expansion absorption (DN 600): ±80 mm; calculation: ASME class. The bellows' development work is not handled within this scope. The bellows are supplied by leading manufacturers, and warrant highest quality. Multiple bellows were selected on the basis of maximum elasticity - a property

  17. Compound odontoma

    Directory of Open Access Journals (Sweden)

    José Marcelo Vargas Pinto

    2008-01-01

    Full Text Available Odontomas are the most common types of odontogenic tumors, as they are considered more as a developmental anomaly (hamartoma than as a true neoplasia. The aim of the present study is to describe a clinical case of compound odontoma, analyzing its most commonsigns, its region of location, the decade of life and patient’s gender, disorders that may occur as well as the treatment proposed. In order to attain this objective, the method was description of the present clinical case and bibliographic revision, arriving at the result that the treatment for this type of lesion invariably is surgical removal (enucleation and curettage and the prognosis is excellent. The surgical result was followed up in the post-operative period by radiographic exam, and it was possible to conclude that there was complete cicatrization and tissue repair.

  18. Imaging the temporomandibular joint

    Energy Technology Data Exchange (ETDEWEB)

    Katzberg, R.W.; Manzione, J.V.; Westesson, P.L.

    1988-01-01

    This book encompasses all imaging modalities as they apply to the Temporomandibular Joint and its disorders. The volume employs correlative line drawings to elaborate on diagnostic images. It helps teach methods of TMJ imaging and describes findings identified by different imaging modalities to both radiologists and dental clinicians.

  19. Imaging the temporomandibular joint

    International Nuclear Information System (INIS)

    This book encompasses all imaging modalities as they apply to the Temporomandibular Joint and its disorders. The volume employs correlative line drawings to elaborate on diagnostic images. It helps teach methods of TMJ imaging and describes findings identified by different imaging modalities to both radiologists and dental clinicians

  20. Temporomandibular joint imaging

    International Nuclear Information System (INIS)

    The temporomandibular joint (TMJ) though close to the surface is one of the most difficult structures to visualise effectively. This is mainly due to the presence of dense bony structures which become superimposed over the image of the joint. The need to visualise this anatomical area is on the increase as more and more patients actively seek treatment for problems related to, and associated with, the craniomandibular articulation. Conventional radiographic techniques used to evaluate the joint have been designed to cope with the unique combination of hard and soft tissues and airspaces found in the maxillofacial region, but still have limitations. With the advent of the space age with its new materials, silicon chips and microcomputers, radiography has given way to diagnostic imaging which covers a range of modalities such as computerised tomography, magnetic resonance imaging, ultrasound and thermography. These are now available to assist in obtaining a clearer picture of the internal structures of the TMJ without the problems of superimposition previously encountered. This article is a resume of the radiographic techniques and a review of the current imaging methods available for assessing disorders of the temporomandibular joint. 21 refs., 3 tabs., 14 figs

  1. Keyed shear joints

    DEFF Research Database (Denmark)

    Hansen, Klaus

    This report gives a summary of the present information on the behaviour of vertical keyed shear joints in large panel structures. An attemp is made to outline the implications which this information might have on the analysis and design of a complete wall. The publications also gives a short...

  2. Equivalent dynamic model of DEMES rotary joint

    Science.gov (United States)

    Zhao, Jianwen; Wang, Shu; Xing, Zhiguang; McCoul, David; Niu, Junyang; Huang, Bo; Liu, Liwu; Leng, Jinsong

    2016-07-01

    The dielectric elastomer minimum energy structure (DEMES) can realize large angular deformations by a small voltage-induced strain of the dielectric elastomer (DE), so it is a suitable candidate to make a rotary joint for a soft robot. Dynamic analysis is necessary for some applications, but the dynamic response of DEMESs is difficult to model because of the complicated morphology and viscoelasticity of the DE film. In this paper, a method composed of theoretical analysis and experimental measurement is presented to model the dynamic response of a DEMES rotary joint under an alternating voltage. Based on measurements of equivalent driving force and damping of the DEMES, the model can be derived. Some experiments were carried out to validate the equivalent dynamic model. The maximum angle error between model and experiment is greater than ten degrees, but it is acceptable to predict angular velocity of the DEMES, therefore, it can be applied in feedforward–feedback compound control.

  3. Towards joint decoding of Tardos fingerprinting codes

    CERN Document Server

    Meerwald, Peter

    2011-01-01

    The class of joint decoder of probabilistic fingerprinting codes is of utmost importance in theoretical papers to establish the concept of fingerprint capacity. However, no implementation supporting a large user base is known to date. This paper presents an iterative decoder which is, as far as we are aware of, the first practical attempt towards joint decoding. The discriminative feature of the scores benefits on one hand from the side-information of previously accused users, and on the other hand, from recently introduced universal linear decoders for compound channels. Neither the code construction nor the decoder make precise assumptions about the collusion (size or strategy). The extension to incorporate soft outputs from the watermarking layer is straightforward. An intensive experimental work benchmarks the very good performances and offers a clear comparison with previous state-of-the-art decoders.

  4. An analysis of a joint shear model for jointed media with orthogonal joint sets

    International Nuclear Information System (INIS)

    This report describes a joint shear model used in conjunction with a computational model for jointed media with orthogonal joint sets. The joint shear model allows nonlinear behavior for both joint sets. Because nonlinear behavior is allowed for both joint sets, a great many cases must be considered to fully describe the joint shear behavior of the jointed medium. An extensive set of equations is required to describe the joint shear stress and slip displacements that can occur for all the various cases. This report examines possible methods for simplifying this set of equations so that the model can be implemented efficiently form a computational standpoint. The shear model must be examined carefully to obtain a computationally efficient implementation that does not lead to numerical problems. The application to fractures in rock is discussed. 5 refs., 4 figs

  5. 复方胃蛋白酶散联合枯草杆菌二联活菌颗粒防治婴幼儿支气管肺炎继发性腹泻临床观察%Clinical observation of compound pepsin combined Bacillus subtilis II joint viables in prevention of infant secondary diarrh ea following bronchial pneumonia

    Institute of Scientific and Technical Information of China (English)

    姚炬文; 全李芳; 谢晓恒

    2015-01-01

    Objective To explore the clinical value of compound pepsin combined Bacillus subtilis II joint viables in preven -tion of infant secondary diarrhea following bronchial pneumonia .Methods Two hundred and sixty infants with bronchial pneumonia were randomly divided into two groups with 130 cases in each group.Both groups were treated with cefoperazone sodium intravenous in -jection and ambroxol hydrochloride inhalation .The control group was given oral compound of pepsin powder and the observation group was added with Bacillus subtilis II combined live bacteria pellet orally .The incidence rate of secondary diarrhea , hospital stay time and diarrhea subsiding time were observed and compared .Results Secondary diarrhea incidence rate in 1-year-old,1 to 2-year old and o-ver 2-year-old children in observation group were lower than that of the control group ( P <0.05); but general secondary diarrhea rate was lower ( P <0.01) and diarrhea subsiding time and hospitalization time were shorter than that of those in control group ( P <0.01 or P <0.05).Conclusion Compound pepsin combined Bacillus subtilis II combined live bacteria oral therapy can reduce secondary diarrhea incidence rate in children with infant bronchial pneumonia and shorten the course of treatment , which is clinically worthy.%目的:探讨复方胃蛋白酶散联合枯草杆菌二联活菌颗粒防治婴幼儿支气管肺炎继发性腹泻的临床效果。方法将260例支气管肺炎患儿随机分为两组,各130例。两组均给予头孢哌酮钠静脉滴注+氨溴索雾化吸入治疗。对照组给予复方胃蛋白酶散口服,观察组加用枯草杆菌二联活菌颗粒口服。观察两组继发性腹泻发生率、腹泻消失时间及住院时间。结果观察组<1岁、1~2岁、>2岁患儿继发性腹泻发生率均低于对照组( P <0.05),总继发性腹泻发生率低于对照组( P <0.01);观察组继发性腹泻患儿腹泻消失时间和住

  6. Joint Infection (Beyond the Basics)

    Science.gov (United States)

    ... for some deep joints (eg, hip, shoulder), surgical placement of a drainage tube. ARTIFICIAL JOINT INFECTION — People ... medications, the user is advised to check the product information sheet accompanying each drug to verify conditions ...

  7. Joint cumulants for natural independence

    OpenAIRE

    Hasebe, Takahiro; Saigo, Hayato

    2011-01-01

    Many kinds of independence have been defined in non-commutative probability theory. Natural independence is an important class of independence; this class consists of five independences (tensor, free, Boolean, monotone and anti-monotone ones). In the present paper, a unified treatment of joint cumulants is introduced for natural independence. The way we define joint cumulants enables us not only to find the monotone joint cumulants but also to give a new characterization of joint cumulants fo...

  8. Serviceability of welded joints in the extreme conditions

    International Nuclear Information System (INIS)

    At design of nuclear fusion reactor the principal importance present the energy-stressed elements of the reactor discharge chambers such as the divertor, limiter, and first wall. Construction of divertor device presents the compound of copper-tungsten type. For implementation of serviceable construction the important task is development of reliable joint between heterogeneous materials. Technology of heterogeneous tungsten-copper welded joints with use of the soldering on the base copper-manganese system is implemented. It is shown, that the soldering has necessary complex of the features (shock viscosity, relative extension) allowing to obtain the welded joints keeping the serviceability under the neutron irradiation conditions, high temperatures, and strong cyclic thermal flows action. In the result od thermo-cyclic tests it is established that the examined welded joints keep serviceability at thermal flow heating with capacity θ=10 MW/m2 during 2·103 cycles

  9. Chapter 17. Bone joints

    International Nuclear Information System (INIS)

    The use of radioisotopes for exploration of the joints and treatment of articular diseases is examined. The joint socket is explored by arthroscintigraphy, a technique applied on a routine basis only to the knee and performed by intra-articular injection of a sup(99m)Tc-labelled colloid. Arthroscintigraphy can be used especially to foresee and to check the distribution of radioactive products employed by synoviortheses (treatment by local injection). Synovial explorations are carried out by iodine 131 - or technetium-99m-labelled albumine and the pertechnetate ion which, injected intraveinously, build up in the inflamed synovial membrane to an extent increasing with the degree of inflammation. The exploration in both qualitative and quantitative. The methode, which uses a conventional scintigraph or a scintillation camera, is described. The treatments discussed are of both the local and general type

  10. JET Joint Undertaking

    International Nuclear Information System (INIS)

    The paper presents the annual report of the Joint European Torus (JET) Joint Undertaking, 1986. The report is divided into two parts: a part on the scientific and technical programme of the project, and a part setting out the administration and organisation of the Project. The first part includes: a summary of the main features of the JET apparatus, the JET experimental programme, the position of the Project in the overall Euratom programme, and how JET relates to other large fusion devices throughout the world. In addition, the technical status of JET is described, as well as the results of the JET operations in 1986. The final section of the first part outlines the proposed future programme of JET. (U.K.)

  11. Joint International Accelerator School

    CERN Multimedia

    CERN Accelerator School

    2014-01-01

    The CERN and US Particle Accelerator Schools recently organised a Joint International Accelerator School on Beam Loss and Accelerator Protection, held at the Hyatt Regency Hotel, Newport Beach, California, USA from 5-14 November 2014. This Joint School was the 13th in a series of such schools, which started in 1985 and also involves the accelerator communities in Japan and Russia.   Photo courtesy of Alfonse Pham, Michigan State University.   The school attracted 58 participants representing 22 different nationalities, with around half from Europe and the other half from Asia and the Americas. The programme comprised 26 lectures, each of 90 minutes, and 13 hours of case study. The students were given homework each day and had an opportunity to sit a final exam, which counted towards university credit. Feedback from the participants was extremely positive, praising the expertise and enthusiasm of the lecturers, as well as the high standard and quality of their lectures. Initial dis...

  12. A joint venturer perspective

    International Nuclear Information System (INIS)

    Many joint ventures are facing potentially huge and usually unquantifiable prospective liabilities as a consequence of the abandonment of energy and resource projects and associated reclamation obligations. It is possible for abandonment costs to be met at least partly by government or collective industry actions. There is, however, a realization amongst joint venturers that where such action has not been taken they need to enter into arrangements amongst themselves. The circumstances under which such security arrangements should be entered into and the form they should take are discussed. Aspects of security provision such as transfer of interest in the project, failure of a participant to provide the security when due and how long security agreements should continue, are also considered. (UK)

  13. Joint hypermobility syndrome pain.

    Science.gov (United States)

    Grahame, Rodney

    2009-12-01

    Joint hypermobility syndrome (JHS) was initially defined as the occurrence of musculoskeletal symptoms in the presence of joint laxity and hypermobility in otherwise healthy individuals. It is now perceived as a commonly overlooked, underdiagnosed, multifaceted, and multisystemic heritable disorder of connective tissue (HDCT), which shares many of the phenotypic features of other HDCTs such as Marfan syndrome and Ehlers-Danlos syndrome. Whereas the additional flexibility can confer benefits in terms of mobility and agility, adverse effects of tissue laxity and fragility can give rise to clinical consequences that resonate far beyond the confines of the musculoskeletal system. There is hardly a clinical specialty to be found that is not touched in one way or another by JHS. Over the past decade, it has become evident that of all the complications that may arise in JHS, chronic pain is arguably the most menacing and difficult to treat. PMID:19889283

  14. Posttraumatic Temporomandibular Joint Disorders

    OpenAIRE

    Giannakopoulos, Helen E.; Quinn, Peter D.; Granquist, Eric; Chou, Joli C.

    2009-01-01

    The temporomandibular joint (TMJ) has many essential functions. None of its components are exempt from injury. Facial asymmetry, malocclusion, disturbances in growth, osteoarthritis, and ankylosis can manifest as complications from trauma to the TMJ. The goals of initial treatment include achievement of pretraumatic function, restoration of facial symmetry, and resolution of pain. These same objectives hold true for late repairs and reconstruction of the TMJ apparatus. Treatment is demanding,...

  15. Jet Joint Undertaking

    International Nuclear Information System (INIS)

    The paper presents the Jet Joint Undertaking annual report 1987. A description is given of the JET and Euratom and International Fusion Programmes. The technical status of JET is outlined, including the development and improvements made to the system in 1987. The results of JET Operation in 1987 are described within the areas of: density effects, temperature improvements, energy confinement studies and other material effects. The contents also contain a summary of the future programme of JET. (U.K.)

  16. Responsibility and joint production

    OpenAIRE

    Petersen, Thomas; Faber, Malte

    2004-01-01

    In this paper, we discuss the relationship between responsibility and joint production. Responsibility mirrors our ability to act freely. We can act freely only if we can assume responsibility for our actions and their consequences; the limits of our responsibility are therefore also the limits of our liberty (part I). Thus, a problem of responsibility arises from our partial ignorance with respect to the consequences which our actions entail. Since this ignorance is at least partly irreducib...

  17. On joint numerical radius

    Czech Academy of Sciences Publication Activity Database

    Müller, Vladimír

    2014-01-01

    Roč. 142, č. 4 (2014), s. 1371-1380. ISSN 0002-9939 R&D Projects: GA ČR GA201/09/0473; GA AV ČR IAA100190903 Institutional support: RVO:67985840 Keywords : joint numerical range * numerical radius Subject RIV: BA - General Mathematics Impact factor: 0.681, year: 2014 http://www.ams.org/journals/proc/2014-142-04/S0002-9939-2014-11876-4/ home .html

  18. Nanotechnology in joint replacement

    OpenAIRE

    Torrecillas, Ramón; J. S. MOYA; Díaz, L. A.; Bartolomé, J. F.; Fernández, Adolfo; Lopez-Esteban, S.

    2009-01-01

    This paper reviews the most relevant achievements and new developments in the field of nanomaterials and their possible impact on the fabrication of a new generation of reliable and longer lasting implants for joint replacement. Special emphasis is given to the role of nanocomposites with different microstructural designs: micro-nano composites, nano-nano composites, macro-micro-nano composites as well as bioinspired hierarchical composite materials. These nanostructured materials have opened...

  19. Prosthetic elbow joint

    Science.gov (United States)

    Weddendorf, Bruce C. (Inventor)

    1994-01-01

    An artificial, manually positionable elbow joint for use in an upper extremity, above-elbow, prosthetic is described. The prosthesis provides a locking feature that is easily controlled by the wearer. The instant elbow joint is very strong and durable enough to withstand the repeated heavy loadings encountered by a wearer who works in an industrial, construction, farming, or similar environment. The elbow joint of the present invention comprises a turntable, a frame, a forearm, and a locking assembly. The frame generally includes a housing for the locking assembly and two protruding ears. The forearm includes an elongated beam having a cup-shaped cylindrical member at one end and a locking wheel having a plurality of holes along a circular arc on its other end with a central bore for pivotal attachment to the protruding ears of the frame. The locking assembly includes a collar having a central opening with a plurality of internal grooves, a plurality of internal cam members each having a chamfered surface at one end and a V-shaped slot at its other end; an elongated locking pin having a crown wheel with cam surfaces and locking lugs secured thereto; two coiled compression springs; and a flexible filament attached to one end of the elongated locking pin and extending from the locking assembly for extending and retracting the locking pin into the holes in the locking wheel to permit selective adjustment of the forearm relative to the frame. In use, the turntable is affixed to the upper arm part of the prosthetic in the conventional manner, and the cup-shaped cylindrical member on one end of the forearm is affixed to the forearm piece of the prosthetic in the conventional manner. The elbow joint is easily adjusted and locked between maximum flex and extended positions.

  20. The Joint Cities

    Directory of Open Access Journals (Sweden)

    Romano Fistola

    2010-04-01

    Full Text Available The new connections, which high speed train allows to activate among the metropolitan systems, seem to be able to give life to new urban macro-structures for which the transfer time, among the main poles of the railway segment, becomes comparable to an inside moving into the city and therefore considered as an inter-functional mobility. The tunnel effect generated by the high speed connection seems to be able to allow a new temporal and functional joint among the metropolitan systems consequently supporting the possibility, for the users, to move themselves among the different urban functions belonging to the different cities. The birth of these urban aggregations seems to drive towards new megalopolis, which we can define for the first time with the term: joint-city. For this new metropolitan settlement it seems to be very interesting to investigate the constitutive peculiarities, the systemic articulation, its relational structures, the evolutionary scenarios, and so on. The urban functions (activities can be considered as structures of relationships between people that allows to define "organizational links" inside the community; the urban functions are located in specific places inside urban container or in open spaces. The urban functions represent the urban engines and the functional system can be thought as the “soul of the city", abstract but essential to its survival. In the definition set out here the analysis is carried out for many interconnected urban functional system points (specifically those in Rome and Naples. The new high speed railway has to be considered not only as a new channel of mobility between cities, but as a real possibility of joint between the functional systems of the two centres. A final consideration can be carried out in relation to the possibility of implementing new measures of governance of urban transformations considering the new macro-city: the "Joint City".

  1. Shoulder joint tuberculosis

    International Nuclear Information System (INIS)

    Despite the fact that joint tuberculosis is one of the most common forms of extrapulmonary tuberculosis, it is a disease entity that is very rare in Poland (less than 100 cases a year in the last 10 years). The symptoms are non-specific, and thus the disease is rarely taken into account in preliminary differential diagnosis. A 68-year-old female patient was admitted to the Internal Diseases Clinic due to oedema and pain of the right shoulder joint. The pain has been increasing for about 8 months. Physical examination revealed increased circumference and elevated temperature of the right shoulder joint. Limb function was retained. The full range of radiological and laboratory diagnostic examinations was performed, including the biopsy of the affected tissue which revealed the presence of Mycobacterium tuberculosis in the bacterial culture. Clinical improvement was obtained after introduction of TB drugs. Radiological diagnostic methods (X-ray, CT scans, MRI scans) provide high precision monitoring of articular lesions. However, the decisive diagnosis requires additional laboratory tests as well as histopathological and bacteriological assays

  2. The neuropathic joint.

    Science.gov (United States)

    Sequeira, W

    1994-01-01

    Neuropathic arthritis is a destructive arthropathy frequently associated with loss of proprioception. A third of patients, however, may have no demonstrable neurological deficit. Patients with diabetes, syphilis, syringomyelia and other neuropathies are particularly prone to developing this joint disease. The diagnosis of Charcot's joints should be considered in anyone who develops what appears to be a severe osteoarthritis or a transverse fracture of the tibia or fibula after minor trauma. Scoliosis with particularly destructive changes on radiography should prompt a search for syringomyelia or syphilis. The most common radiographic abnormalities are those of distension in 3D (Dislocation, Destruction and Degeneration). An atrophic form with resorption of the proximal humerus, most frequently described in syringomyelia, has been observed in diabetes. Loss of the distal end of the clavicle has not been described before in the neuropathies. These changes coupled with speckled calcification or shards of bone in the periarticular soft tissue confirm the diagnosis. Infection and CPPD crystal disease can be difficult to exclude. The joint fluid may be inflammatory and infection may be a complication. Treatment includes anti-inflammatories and splinting. Indications for surgery are limited. PMID:8070170

  3. Formation of tough composite joints

    International Nuclear Information System (INIS)

    Joints which exhibit tough fracture behavior were formed in a composite with a Si/SiC matrix reinforced with Textron SCS-6 fibers with either boron nitride or silicon nitride fiber coatings. In composites with BN coatings fibers were aligned uniaxially, while composites with Si3N4-coated fibers had a 0/90 degree architecture. Lapped joints (joints with overlapping fingers) were necessary to obtain tough behavior. Geometrical requirements necessary to avoid brittle joint failure have been proposed. Joints with a simple overlap geometry (only a few fingers) would have to be very long in order to prevent brittle failure. Typical failure in these joints is caused by a crack propagating along the interfaces between the joint fingers. Joints of the same overall length, but with geometry changed to be symmetric about the joint centerline and with an extra shear surface exhibited tough fractures accompanied with extensive fiber pullout. The initial matrix cracking of these joints was relatively low because cracks propagated easily through the ends of the fingers. Joints with an optimized stepped sawtooth geometry produced composite-like failures with the stress/strain curves containing an elastic region followed by a region of rising stress with an increase of strain. Increasing the fiber/matrix interfacial strength from 9 to 25 MPa, by changing the fiber coating, increased matrix cracking and ultimate strength of the composite significantly. The best joints had matrix cracking stress and ultimate strength of 138 and 240 MPa, respectively. Joint failure was preceded by multiple matrix cracking in the entire composite. The high strength of the joints will permit building of structures containing joints with only a minor reduction of design stresses

  4. Formation of tough composite joints

    Energy Technology Data Exchange (ETDEWEB)

    Brun, M.K. [GE Corporate Research and Development, Schenectady, NY (United States)

    1997-05-01

    Joints which exhibit tough fracture behavior were formed in a composite with a Si/SiC matrix reinforced with Textron SCS-6 fibers with either boron nitride or silicon nitride fiber coatings. In composites with BN coatings fibers were aligned uniaxially, while composites with Si{sub 3}N{sub 4}-coated fibers had a 0/90{degree} architecture. Lapped joints (joints with overlapping fingers) were necessary to obtain tough behavior. Geometrical requirements necessary to avoid brittle joint failure have been proposed. Joints with a simple overlap geometry (only a few fingers) would have to be very long in order to prevent brittle failure. Typical failure in these joints is caused by a crack propagating along the interfaces between the joint fingers. Joints of the same overall length, but with geometry changed to be symmetric about the joint centerline and with an extra shear surface exhibited tough fractures accompanied with extensive fiber pullout. The initial matrix cracking of these joints was relatively low because cracks propagated easily through the ends of the fingers. Joints with an optimized stepped sawtooth geometry produced composite-like failures with the stress/strain curves containing an elastic region followed by a region of rising stress with an increase of strain. Increasing the fiber/matrix interfacial strength from 9 to 25 MPa, by changing the fiber coating, increased matrix cracking and ultimate strength of the composite significantly. The best joints had matrix cracking stress and ultimate strength of 138 and 240 MPa, respectively. Joint failure was preceded by multiple matrix cracking in the entire composite. The high strength of the joints will permit building of structures containing joints with only a minor reduction of design stresses.

  5. Laboratory characterization of rock joints

    International Nuclear Information System (INIS)

    A laboratory characterization of the Apache Leap tuff joints under cyclic pseudostatic and dynamic loads has been undertaken to obtain a better understanding of dynamic joint shear behavior and to generate a complete data set that can be used for validation of existing rock-joint models. Study has indicated that available methods for determining joint roughness coefficient (JRC) significantly underestimate the roughness coefficient of the Apache Leap tuff joints, that will lead to an underestimation of the joint shear strength. The results of the direct shear tests have indicated that both under cyclic pseudostatic and dynamic loadings the joint resistance upon reverse shearing is smaller than that of forward shearing and the joint dilation resulting from forward shearing recovers during reverse shearing. Within the range of variation of shearing velocity used in these tests, the shearing velocity effect on rock-joint behavior seems to be minor, and no noticeable effect on the peak joint shear strength and the joint shear strength for the reverse shearing is observed

  6. Laboratory characterization of rock joints

    Energy Technology Data Exchange (ETDEWEB)

    Hsiung, S.M.; Kana, D.D.; Ahola, M.P.; Chowdhury, A.H.; Ghosh, A. [Southwest Research Inst., San Antonio, TX (United States). Center for Nuclear Waste Regulatory Analyses

    1994-05-01

    A laboratory characterization of the Apache Leap tuff joints under cyclic pseudostatic and dynamic loads has been undertaken to obtain a better understanding of dynamic joint shear behavior and to generate a complete data set that can be used for validation of existing rock-joint models. Study has indicated that available methods for determining joint roughness coefficient (JRC) significantly underestimate the roughness coefficient of the Apache Leap tuff joints, that will lead to an underestimation of the joint shear strength. The results of the direct shear tests have indicated that both under cyclic pseudostatic and dynamic loadings the joint resistance upon reverse shearing is smaller than that of forward shearing and the joint dilation resulting from forward shearing recovers during reverse shearing. Within the range of variation of shearing velocity used in these tests, the shearing velocity effect on rock-joint behavior seems to be minor, and no noticeable effect on the peak joint shear strength and the joint shear strength for the reverse shearing is observed.

  7. Posttraumatic temporomandibular joint disorders.

    Science.gov (United States)

    Giannakopoulos, Helen E; Quinn, Peter D; Granquist, Eric; Chou, Joli C

    2009-05-01

    The temporomandibular joint (TMJ) has many essential functions. None of its components are exempt from injury. Facial asymmetry, malocclusion, disturbances in growth, osteoarthritis, and ankylosis can manifest as complications from trauma to the TMJ. The goals of initial treatment include achievement of pretraumatic function, restoration of facial symmetry, and resolution of pain. These same objectives hold true for late repairs and reconstruction of the TMJ apparatus. Treatment is demanding, and with opposing approaches. The following article explores various treatment options for problems presenting as a result of a history of trauma to the TMJ. PMID:22110802

  8. Joint Advisory Appeals Board

    CERN Document Server

    HR Department

    2006-01-01

    The Joint Advisory Appeals Board was convened to examine an appeal lodged by a member of the personnel with regard to advancement. The person concerned has requested that the report of the Board and the final decision of the Director-General be brought to the notice of the personnel in accordance with Article R VI 1.20 of the Staff Regulations. The relevant documents will therefore be posted on the notice boards of the Administration Building (No. 60) from 24 March to 10 April 2006. Human Resources Department Tel. 74128

  9. Joint Advisory Appeals Board

    CERN Multimedia

    2003-01-01

    The Joint Advisory Appeals Board was convened to examine the appeal lodged by Mrs Judith Igo-Kemenes concerning the application of procedures foreseen by Administrative Circular N§ 26 (Rev. 3). As the appellant has not objected, the report of the Board and the final decision of the Director-General are brought to the notice of the personnel in accordance with Article R VI 1.20 of the Staff Regulations. The relevant documents will therefore be posted on the notice boards of the Administration Building (N° 60) from 6 to 20 June 2003. Human Resources Division Tel. 74128

  10. THE JOINT MONITORING COMMISSION

    Directory of Open Access Journals (Sweden)

    Helmoed-Römer Heitman

    2012-02-01

    Full Text Available The Joint Monitoring Commission (JMC was created to oversee the withdrawal of South African forces from the portion of Angola's southern Cunene province in which they had operated for some time, and its re-occupation by the Angolan Armed Forces (Fapla. It was to ensure that neither Swapo nor Cuban forces moved into this area as the South African Defence Force (SADF withdrew. The JMC consisted of SADF and Fapla headquarters (HQ personnel and infantry from both armies to monitor the area concerned. It operated in southern Angola from February 1984 to May 1985.

  11. Ulnar joint synovial sarcoma

    International Nuclear Information System (INIS)

    Statement of the diagnosis of synovial sarcoma in early period on the example of one patient is analyzed. It is too difficult to diagnose synovial sarcoma. Comprehensive X-ray ultrasonic examination is the most informative in detection of tumor. Surgical removal of revealed formation has been conducted to the patient. The formation is dense, joined to muscular fibers, is not connected with the joint. Histological investigation of the formation determines dissemination of malignant tumor, presented by round or oval cells. Tumor tissue is devided by thick fibrous layers, surrounded by fibrous capsula. The following conclusion is given: synovial sarcoma

  12. Tarsometatarsal/Lisfranc joint.

    Science.gov (United States)

    DiDomenico, Lawrence A; Cross, Davi

    2012-04-01

    Accurate early diagnosis with adequate reduction and maintenance of anatomic alignment of the dislocation or fracture within the Lisfranc joint complex have been found to be the key to successful outcomes regarding this injury. Because of the anatomic variations, the thin soft tissue envelop, and the abundance of ligamentous and capsular structures in the region, repair of these injuries can be a challenge. The classification systems used to describe these injuries aid in describing the mechanism of injury or displacement type present, which may aid in determining what treatment modality can provide the best outcome. PMID:22424486

  13. Joint Advisory Appeals Board

    CERN Multimedia

    2003-01-01

    The Joint Advisory Appeals Board was convened to examine the appeal lodged by Mr Poul Frandsen concerning his assimilation into the new career structure. As the appellant has not objected, the report of the Board and the final decision of the Director-General are brought to the notice of the personnel in accordance with Article R VI 1.20 of the Staff Regulations. The relevant documents will therefore be posted on the notice boards of the Administration Building (N° 60) from 13 to 24 January 2003. Human Resources Division Tel. 74128

  14. Embrittlement of welded joints

    International Nuclear Information System (INIS)

    The structure of a weld is considered and the role of the main parts of a welded joint in the appearance of defects during welding is determined. Factors greatly affecting hot crack formation (heat removal, impurity redistribution, volume of welding bath, welding rate) are shown. Reasons for the appearance of cracks not related to crystallization process (subsequent heat treatment, plastic working, etc.) are analyzed. The process of cold cracking of welds due to hydrogen absorption and relaxation of high welding stresses, is investigated. Methods to avoid cold cracking are described. Mechanisms of weld embrittlement are considered using as examples steels and high nickel alloys. 248 refs.; 28 figs.; 2 tabs

  15. Joint Advisory Appeals Board

    CERN Document Server

    2013-01-01

    The Joint Advisory Appeals Board has examined the internal appeal lodged by a former member of the personnel, a beneficiary of the CERN Pension Fund, against the calculation of his pension in the framework of the Progressive Retirement Programme.   The person concerned has not objected to the report of the Board and the final decision of the Director-General being brought to the attention of the members of the personnel. In application of Article R VI 1.18 of the Staff Regulations, these documents will therefore be available from 26 July to 11 August 2013 at the following link. HR Department Head Office

  16. Optical rotary joint

    Science.gov (United States)

    May, R. G., Jr.

    1982-06-01

    The primary objective of this contract is the design, fabrication, and testing of an optical rotary joint which permits transmission of signals through optical fibers across the interface of two environments rotating relative to each other. Outstanding optical performance is achieved through the use of gradient index lenses to couple radiation across the separation between two fibers. The salient features of this device are bidirectional operation at two wavelengths (850 nm and 1300 nm), low insertion loss, low rotationally induced variation of attenuation, a seven-circuit electrical slip-ring assembly, and rugged construction. The device is designed to facilitate the application of future designs to pressurized, subsea environments.

  17. Joint Advisory Appeals Board

    CERN Multimedia

    HR Department

    2008-01-01

    The Joint Advisory Appeals Board has examined the internal appeal lodged by a member of the personnel against the decision to grant him only a periodic one-step advancement for the 2006 reference year. The person concerned has not objected to the report of the Board and the final decision of the Director-General being brought to the attention of the members of the personnel. In application of Article R VI 1.18 of the Staff Regulations, these documents will therefore be posted on the notice board of the Main building (bldg. 500) from 1 September to 14 September 2008. Human Resources Department (73911)

  18. Joint Advisory Appeals Board

    CERN Multimedia

    HR Department

    2008-01-01

    The Joint Advisory Appeals Board has examined the internal appeal lodged by a member of the personnel against the decision to grant him only a periodic one-step advancement for the 2006 reference year. The person concerned has not objected to the report of the Board and the final decision of the Director-General being brought to the attention of the members of the personnel. In application of Article R VI 1.18 of the Staff Regulations, these documents will therefore be posted on the notice board of the Main Building (Bldg. 500) from 1 September to 14 September 2008. Human Resources Department (73911)

  19. Joint Advisory Appeals Board

    CERN Multimedia

    HR Department

    2007-01-01

    The Joint Advisory Appeals Board was convened to examine an internal appeal lodged by a member of the personnel with regard to the decision not to grant him an indefinite contract. The person concerned has requested that the report of the Board and the final decision of the Director-General be brought to the notice of the members of the personnel, in accordance with Article R VI 1.18 of the Staff Regulations. The relevant documents will therefore be posted on the notice board of the Main building (Bldg. 60) from 24 September to 7 October 2007. Human Resources Department

  20. Joint Advisory Appeals Board

    CERN Multimedia

    HR Department

    2008-01-01

    The Joint Advisory Appeals Board has examined the internal appeal lodged by a member of the personnel with regard to the decision not to award him a periodic one-step advancement for the 2006 reference year. The person concerned has not objected to the report of the Board and the final decision of the Director-General being brought to the notice of the members of the personnel. In application of Article R VI 1.18 of the Staff Regulations, these documents will therefore be posted on the notice board of the Main building (Bldg. 500) from 17 March to 30 March 2008. Human Resources Department Tel. 73911

  1. Joint Advisory Appeals Board

    CERN Multimedia

    HR Department

    2008-01-01

    The Joint Advisory Appeals Board has examined the internal appeal lodged by a member of the personnel with regard to the decision not to grant him an indefinite contract. The person concerned has not objected to the report of the Board and the final decision of the Director-General being brought to the notice of the members of the personnel. In application of Article R VI 1.18 of the Staff Regulations, these documents will therefore be posted on the notice board of the Main Building (Bldg. 500) from 26 May to 6 June 2008. Human Resources Department (73911)

  2. Joint Advisory Appeals Board

    CERN Multimedia

    HR Department

    2008-01-01

    The Joint Advisory Appeals Board was convened to examine an internal appeal lodged by a member of the personnel with regard to the decision not to grant him an indefinite contract. The person concerned has not objected to the report of the Board and the final decision of the Director-General being brought to the notice of the members of the personnel, in accordance with Article R VI 1.18 of the Staff Regulations. These documents will therefore be posted on the notice board of the Main Building (Bldg. 60) from 21 January to 3 February 2008. Human Resources Department (73911)

  3. Joint Advisory Appeals Board

    CERN Multimedia

    2003-01-01

    The Joint Advisory Appeals Board was convened to examine the appeal lodged by Mr Aloïs Girardoz with regard to classification and advancement. As the appellant has not objected, the Board's report and the Director-General's decision will be brought to the notice of the personnel in accordance with Article R VI 1.20 of the Staff Regulations. The relevant documents will therefore be posted on the notice boards of the Administration Building (N° 60) from 15 to 29 August 2003. Human Resources Division Tel. 74128

  4. Lisfranc Joint Injuries

    Institute of Scientific and Technical Information of China (English)

    Lisa Chinn

    2009-01-01

    @@ The ankle and foot are the most common sites for athletic injuries.[1]Midfoot,or Lisfranc,injuries are the second most common foot injury and have a high in cidence in particular sports.They account for 4% of all football injuries per year,occurring frequently in linemen.[2]They are also common in equestrians,surfers,and windsurfers.[2]Lisfranc injuries are often misdiagnosed and if not treated properly can have lingering symptoms.It is estimated that Lisfranc joint injuries occur in 1 in every 55,000 persons every year.[3,4

  5. Joint-sparing Corrections in Malunited Lisfranc Joint Injuries.

    Science.gov (United States)

    Nery, Caio; Raduan, Fernando; Baumfeld, Daniel

    2016-03-01

    Lisfranc fracture-dislocations are very serious and potentially disabling injuries. Unfortunately, they are often misdiagnosed. Multiplanar midfoot deformities that result from these fracture-dislocations are precursors of joint degeneration and significant functional disabilities. Anatomic reduction with different types of internal fixation is an efficient method to reconstruct midfoot alignment and stability. Joint-preserving reconstruction techniques emerge as a viable alternative to corrective fusion as they achieve stable joint realignment with preserved motion. PMID:26915786

  6. Jointly Sponsored Research Program

    Energy Technology Data Exchange (ETDEWEB)

    Everett A. Sondreal; John G. Hendrikson; Thomas A. Erickson

    2009-03-31

    U.S. Department of Energy (DOE) Cooperative Agreement DE-FC26-98FT40321 funded through the Office of Fossil Energy and administered at the National Energy Technology Laboratory (NETL) supported the performance of a Jointly Sponsored Research Program (JSRP) at the Energy & Environmental Research Center (EERC) with a minimum 50% nonfederal cost share to assist industry in commercializing and effectively applying highly efficient, nonpolluting energy systems that meet the nation's requirements for clean fuels, chemicals, and electricity in the 21st century. The EERC in partnership with its nonfederal partners jointly performed 131 JSRP projects for which the total DOE cost share was $22,716,634 (38%) and the nonfederal share was $36,776,573 (62%). Summaries of these projects are presented in this report for six program areas: (1) resource characterization and waste management, (2) air quality assessment and control, (3) advanced power systems, (4) advanced fuel forms, (5) value-added coproducts, and (6) advanced materials. The work performed under this agreement addressed DOE goals for reductions in CO{sub 2} emissions through efficiency, capture, and sequestration; near-zero emissions from highly efficient coal-fired power plants; environmental control capabilities for SO{sub 2}, NO{sub x}, fine respirable particulate (PM{sub 2.5}), and mercury; alternative transportation fuels including liquid synfuels and hydrogen; and synergistic integration of fossil and renewable resources.

  7. Volatile Organic Compounds (VOCs)

    Science.gov (United States)

    ... Organic Compounds' Impact on Indoor Air Quality Volatile Organic Compounds' Impact on Indoor Air Quality On this page: ... Exposure Standards or Guidelines Additional Resources Introduction Volatile organic compounds (VOCs) are emitted as gases from certain solids ...

  8. Ball-joint grounding ring

    Science.gov (United States)

    Aperlo, P. J. A.; Buck, P. A.; Weldon, V. A.

    1981-01-01

    In ball and socket joint where electrical insulator such as polytetrafluoroethylene is used as line to minimize friction, good electrical contact across joint may be needed for lightning protection or to prevent static-charge build-up. Electrical contact is maintained by ring of spring-loaded fingers mounted in socket. It may be useful in industry for cranes, trailers, and other applications requiring ball and socket joint.

  9. Goniometry in limited joint mobility

    OpenAIRE

    Gopinath, S.; Manoj, K.; Rubiya

    2012-01-01

    Aim: To study about the utility of goniometry in screening for limited joint mobility (LJM) in patients attending a secondary level Diabetic Clinic. Materials and Methods: Randomly selected data of 100 patients attending a secondary level diabetic clinic without any complications were used. Baseline neuropathy assessments, namely monofilament and biothesiometry were done. Range of movement around the ankle joint and 1 st metatarsal joint was done using goniometry. Both the results were compar...

  10. The Challenges of Joint Attention

    OpenAIRE

    Kaplan, Frederic; Hafner, Verena

    2004-01-01

    This paper discusses the concept of joint attention and the different skills underlying its development. We argue that joint attention is much more than gaze following or simultaneous looking because it implies a shared intentional relation to the world. The current state-of-the-art in robotic and computational models of the different prerequisites of joint attention is discussed in relation with a developmental timeline drawn from results in child studies.

  11. Joint audits - benefit or burden?

    DEFF Research Database (Denmark)

    Holm, Claus; Thinggaard, Frank

    audits to be a net burden. Furthermore, based on DeAngelo's (1981) initial audit pricing model and legislators' claim that joint audits are an unnecessary economic burden to the companies we predict and find discounts (of around 25%) in audit fees in companies that change to single audits. The primary...... joint audit regime to a single auditor/voluntary joint audit regime. The dataset used in this paper has been collected for the full population of non-financial Danish companies listed on the Copenhagen Stock Exchange (CSE) in the years 2004 and 2005. We find that a majority of firms perceive joint...

  12. Evaluation of interfacial microstructures in dissimilar joints of aluminum alloys to steel using nanoindentation technique

    International Nuclear Information System (INIS)

    The characteristics of interfacial microstructures with additional elements in dissimilar 6000 system aluminum/steel joints were basically evaluated using tensile test, EPMA, TEM and nanoindentation. For Si (and Cu)-added alloy (S1 and SC), EPMA analysis showed that Si (and Cu) was enrichment in the reaction layers, which were formed during diffusion bonding. SAED pattern clarified that the reaction compounds at the interface changed from AlFe intermetalic compounds to AlFeSi intermetalic compounds by Si addition. Nanoindentation technique was successfully applied to the interfacial microstructures to understand directly the nanoscopic mechanical properties in the interfacial microstructures. The hardness and Young's modulus of Al3Fe intermetalic compounds was lower than those of Al2Fe5 intermetalic compounds. Moreover, the hardness and Young's modulus of AlFeSi(Cu) compounds were lower than those of Al3Fe, indicating that the crystal system changed from orthorhombic structure to cubic structure. Joint strength of SC/steel joints was higher than that of the aluminum alloy with no additional element (Base)/ steel joint, indicating that interfacial microstructure was modified by the addition of Si and Cu to the 6000 system aluminum alloy. These results suggest that the nanoscopic mechanical properties at the interface microstructures affect greatly the macroscopic deformation behavior of the aluminum /steel dissimilar joints.

  13. Index of Joint Condition for PVC push-fit joints

    NARCIS (Netherlands)

    Arsenio, A.M.; Vreeburg, J.H.G.; Rietveld, L.

    2014-01-01

    The Index of Joint Condition (IJC) for polyvinyl chloride (PVC) push-fit joints, discussed in this article, was derived from installation guidelines and from destructive laboratory tests. The IJC is presented in a graphical framework and is a powerful tool to employ in order to visualize and compare

  14. TEMPOROMANDIBULAR-JOINT OSTEOARTHROSIS AND GENERALIZED JOINT HYPERMOBILITY

    NARCIS (Netherlands)

    DIJKSTRA, PU; DEBONT, LGM; STEGENGA, B; BOERING, G

    1992-01-01

    Peripheral joint mobility of temporomandibular joint (TMJ) osteoarthrosis and internal derangement patients (n = 25) and of a control group (n = 29) was measured according to a rigidly standardized protocol, in order to study the relationships between TMJ osteoarthrosis and internal derangement and

  15. Temporomandibular joint arthrography

    International Nuclear Information System (INIS)

    The stress and occlusion disturbance are very important etiologic factors in the temporomandibular joint (TMJ) pain dysfunction syndromes. Authors performed TMJ arthrograms in the patients with TMJ problem such as pain, click sound, limited motion and locking, etc. The following results noted: 1. The arthrographic findings of 22 TMJ were analyzed. a) Normal: 6 cases b) Anterior disc displacement with rediction: 6 cases · Early reduction: 2 cases · Intermediate reduction: 3 cases · Late reduction: 1 case c) Anterior disc displacement without reduction: 6 cases · Two cases had adhesion between the posterior portion of disc and the posterior surfaces of the articular eminence. 2. Among 22 cases, the clinical findings of 16 cases (73%) were compatible with arthrographic findings. 6 cases showed disparity between them.

  16. Effect of Joint Scale and Processing on the Fracture of Sn-3Ag-0.5Cu Solder Joints: Application to Micro-bumps in 3D Packages

    Science.gov (United States)

    Talebanpour, B.; Huang, Z.; Chen, Z.; Dutta, I.

    2016-01-01

    In 3-dimensional (3D) packages, a stack of dies is vertically connected to each other using through-silicon vias and very thin solder micro-bumps. The thinness of the micro-bumps results in joints with a very high volumetric proportion of intermetallic compounds (IMCs), rendering them much more brittle compared to conventional joints. Because of this, the reliability of micro-bumps, and the dependence thereof on the proportion of IMC in the joint, is of substantial concern. In this paper, the growth kinetics of IMCs in thin Sn-3Ag-0.5Cu joints attached to Cu substrates were analyzed, and empirical kinetic laws for the growth of Cu6Sn5 and Cu3Sn in thin joints were obtained. Modified compact mixed mode fracture mechanics samples, with adhesive solder joints between massive Cu substrates, having similar thickness and IMC content as actual micro-bumps, were produced. The effects of IMC proportion and strain rate on fracture toughness and mechanisms were investigated. It was found that the fracture toughness G C decreased with decreasing joint thickness ( h Joint). In addition, the fracture toughness decreased with increasing strain rate. Aging also promoted alternation of the crack path between the two joint-substrate interfaces, possibly proffering a mechanism to enhance fracture toughness.

  17. Saving Joint with Aerosol physics

    International Nuclear Information System (INIS)

    Full text: Using electro spray method to analyze wear debris from artificial joints. Well known aerosol techniques have been applied to determine the size distribution and concentration of wear particles found in joint fluids. The organic fraction (cells and large molecules) are removed by digestion. Knowing these data the risk of clogging of blood vessels can be medicinally reduced. (author)

  18. Exercise and the Knee Joint.

    Science.gov (United States)

    Clarke, H. Harrison, Ed.

    1976-01-01

    This report by the President's Council on Physical Fitness and Sports examines the effects of various forms of physical exercise on the knee joint which, because of its vulnerability, is especially subject to injury. Discussion centers around the physical characteristics of the joint, commonly used measurements for determining knee stability,…

  19. Joint mathematical weekend in Copenhagen

    DEFF Research Database (Denmark)

    Raussen, Martin

    2008-01-01

    Notes from the 2008 joint mathematical weekend (29.02-02.03.2008) organized by the Danish Mathematical Society......Notes from the 2008 joint mathematical weekend (29.02-02.03.2008) organized by the Danish Mathematical Society...

  20. MRI of the Temporomandibular Joint

    Directory of Open Access Journals (Sweden)

    Hashem Sharifian

    2010-05-01

    Full Text Available Before recent advances in the last three decades, evaluation of the temporomandiular joint (TMJ was primarily done by plain radiography and arthrography."nCT scan adds more detail in the study of articular surfaces and anatomy of the joint. However, no direct vision upon delicate structures of the joint was available."nMRI has changed this point of view by high contrast resolution of soft tissues."nNevertheless, various pulse sequences and imaging techniques in this modality, cause some controversy and confusion about the best technique for detection of anatomy of the joint and its different pathologic conditions."nAfter a concise review of the anatomy and defining various techniques, our scope is to verify which of these pulse sequences can better delineate joint structures and disorders.

  1. Induction brazing of complex joints

    DEFF Research Database (Denmark)

    Henningsen, Poul; Zhang, Wenqi; Bay, Niels

    2003-01-01

    Induction brazing is a fast and appropriate method for industrial joining of complex geometries and metal combinations. In all types of brazing processes it is important to heat the joint interface of the two materials to the same, high temperature. If one of the specimens is warmer than the other......, or if the hottest area is located outside the joint interface, a number of defects may appear: the braze metal may flow away from the joint, the flux may burn off, poor binding of the braze metal may appear or the braze metal may be overheated. Joint geometry as well as electro-magnetic properties of...... the work piece materials has large influence on the heating time and temperature distribution in induction heating. In order to ensure high and uniform temperature distribution near the interface of a joint between dissimilar materials the precise coil geometry and position is of great importance. The...

  2. Space Station alpha joint bearing

    Science.gov (United States)

    Everman, Michael R.; Jones, P. Alan; Spencer, Porter A.

    1987-01-01

    Perhaps the most critical structural system aboard the Space Station is the Solar Alpha Rotary Joint which helps align the power generation system with the sun. The joint must provide structural support and controlled rotation to the outboard transverse booms as well as power and data transfer across the joint. The Solar Alpha Rotary Joint is composed of two transition sections and an integral, large diameter bearing. Alpha joint bearing design presents a particularly interesting problem because of its large size and need for high reliability, stiffness, and on orbit maintability. The discrete roller bearing developed is a novel refinement to cam follower technology. It offers thermal compensation and ease of on-orbit maintenance that are not found in conventional rolling element bearings. How the bearing design evolved is summarized. Driving requirements are reviewed, alternative concepts assessed, and the selected design is described.

  3. General joint hypermobility and temporomandibular joint derangement in adolescents.

    OpenAIRE

    Westling, L; Mattiasson, A.

    1992-01-01

    Joint mobility was assessed in each member of an epidemiological sample of 96 girls and 97 boys, 17 years old, and graded by means of the hypermobility score of Beighton et al. Twenty two per cent of the girls and 3% of the boys could perform five or more of the nine manoeuvres. The prevalence of symptoms and signs of internal derangement in the temporomandibular joint was higher in adolescents with hypermobility of joints (score greater than or equal to 5/9). In subjects with a high mobility...

  4. Joint seal in tank

    International Nuclear Information System (INIS)

    A seal for a joint or gap between edges of adjacent wall sections (e.g. of concrete) of a liquid-containing vessel, such as a nuclear reactor cooling pond, comprises a sheet metal strip having longitudinally-extending edge parts, secured to the respective vessel-section edges, and a central part which is longitudinally corrugated to provide sufficient flexibility to accommodate slight relative movements between the vessel-section edges (e.g. due to thermal expansions). The edges of the sheet metal of the strip are turned in so that the edge parts of the strip are formed as generally U-section channels. These accommodate longitudinally extending securing bars which are bolted to the vessel wall sections by bolts which pass through the bars, through the free-edged wall of the channel section and through a longitudinally extending resilient seal pad compressed between that wall of the channel section and the vessel wall section to which it is secured. The other wall of the channel section (integral with the corrugated central part of the strip) has access windows through which the bolts are inserted and tightened, the windows being then closed off in liquid-tight manner by welding closure caps over them. (author)

  5. TEMPOROMANDIBULAR-JOINT OSTEOARTHROSIS AND TEMPOROMANDIBULAR-JOINT HYPERMOBILITY

    NARCIS (Netherlands)

    DIJKSTRA, PU; DEBONT, LGM; DELEEUW, R; STEGENGA, B; BOERING, G

    1993-01-01

    For studying the relationship between condylar hypermobility of the temporomandibular joint (TMJ) and osteoarthrosis (OA), 13 patients with bilateral condylar hypermobility were evaluated clinically and radiographically, 30 years after non-surgical treatment. The evaluation included range of motion,

  6. Osteoarthritis of the Wrist STT Joint and Radiocarpal Joint

    OpenAIRE

    Ronit Wollstein; Julio Clavijo; Gilula, Louis A.

    2012-01-01

    Our understanding of wrist osteoarthritis (OA) lags behind that of other joints, possibly due to the complexity of wrist biomechanics and the importance of ligamentous forces in the function of the wrist. Scaphotrapeziotrapezoidal (STT) OA is common, but its role in wrist clinical pathology and biomechanics is unclear. We identified the prevalence of radiographic STT joint OA in our hand clinic population and defined the relationship between STT and radiocarpal OA in wrist radiographs. One hu...

  7. Microstructures and properties of capacitor discharge welded joint of TiNi shape memory alloy and stainless steel

    Institute of Scientific and Technical Information of China (English)

    Li Minggao; Sun Daqian; Qiu Xiaoming; Sun Dexin; Yin Shiqiang

    2005-01-01

    Microstructures and properties of capacitor discharge welded (CDW) joint of TiNi shape memory alloy (SMA) and stainless steel (SS) were studied. The fracture characteristics of the joint were analyzed by means of scanning electron microscope (SEM). Microstructures of the joint were examined by means of optical microscope and SEM. The results showed that the tensile strength of the inhomogeneous joint ( TiNi-SS joint) was low and the joint was brittle. Because TiNi SMA and SS melted, a brittle as-cast structure and compound were formed in the weld. The tensile strength and the shape memory effect (SME) of TiNi-SS joint were strongly influenced by the changes of composition and structure of the weld. Measures should be taken to prevent defects from forming and extruding excessive molten metal in the weld for improving the properties of TiNi-SSjoint.

  8. Formation process,microstructure and mechanical property of transient liquid phase bonded aluminium-based metal matrix composite joint

    Institute of Scientific and Technical Information of China (English)

    孙大谦; 刘卫红; 贾树盛; 邱小明

    2004-01-01

    The formation process, microstructure and mechanical properties of transient liquid phase (TLP) bonded aluminium-based metal matrix composite (MMC) joint with copper interlayer were investigated. The formation process of the TLP joint comprises a number of stages: plastic deformation and solid diffusion (stage 1), dissolution of interlayer and base metal (stage 2), isothermal solidification (stage 3) and homogenization (stage 4). The microstructure of the joint depends on the joint formation process (distinct stages). The plastic deformation and solid diffusion in stage 1 favoure the intimate contact at interfaces and liquid layer formation. The microstructure of joint consists of aluminium solid solution, alumina particle, Al2Cu and MgAl2O4 compounds in stage 2. The most pronounced feature of joint microstructure in stage 3 is the alumina particle segregation in the center of the joint. The increase of joint shear strength with increasing bonding temperature is mainly attributed to improving the fluidity and wettability of liquid phase and decreasing the amount of Al2Cu brittle phase in the joint. The principal reason of higher bonding temperature (>600 ℃) resulting in lowering obviously the joint shear strength is the widening of alumina particle segregation region that acts as a preferential site for failure. The increase of joint shear strength with increasing holding time is mainly associated with decreasing the amount of Al2 Cu brittle phase and promoting homogenization of joint.

  9. Finishing touch to joint venture

    CERN Multimedia

    2003-01-01

    "A new process for polishing titanium and its alloys has been announced following an agreement between Bripol (an Anopol/Delmet joint venture) of Birmingham and the European Organisation for Nuclear Reseach (CERN) in Geneva" (1 paragraph).

  10. Practical aspects of joint implementation

    International Nuclear Information System (INIS)

    Article 4, 2a of the UN Framework Convention on Climate Change states the possibility of joint policies of different countries to achieve national greenhouse gas reduction commitments (Joint Implementation). The cost of reducing greenhouse gas emissions can be reduced drastically if industrialized countries shift abatement activities to developing countries as marginal cost of reduction is much higher in the former countries. In this way economic efficiency of abatement measures can be raised to the point where marginal cost is equal all over the world. At the Conference of the Parties in Berlin in March 1995, criteria for Joint Implementation are to be established. The paper discusses possible forms of Joint Implementation and develops criteria

  11. MRI of the hip joint

    International Nuclear Information System (INIS)

    Magnetic resonance imaging (MRI) is performed to diagnose many pathologic conditions affecting the hip joint. Either conventional MRI (without contrast enhancement of the joint cavity) or MR arthrography is used to detect and most accurately differentiate hip joint pathologies. Conventional MRI is performed in cases of bone marrow edema, necrosis, arthrosis and especially the so-called ''activated arthrosis'', as well as in inflammatory and tumorous entities. MR arthography, which has only recently become available for use, is excellently suited for diagnosing lesions of the acetabular labrum, cartilage lesions, and free articular bodies. This article provides an overview about MRI characteristics and their accuracy of hip joint diseases and the impact on the therapeutic procedure. (orig.)

  12. US Joint Ventures 2014 revision

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — A joint venture is a self-directed partnership of agencies, organizations, corporations, tribes, or individuals that has formally accepted the responsibility of...

  13. Joint Performance and Planning System

    Data.gov (United States)

    US Agency for International Development — A joint State/USAID system hosted by State that integrates resource and performance information at the program level and enables more flexible and frequent entry of...

  14. MR imaging of the metacarpophalangeal joints of the fingers: evaluation of 38 patients with chronic joint disability

    International Nuclear Information System (INIS)

    To report the MR imaging findings of painful injured metacarpophalangeal (MCP) joints of the fingers. MR imaging of 39 injured MCP joints in 38 patients was performed after a mean delay of 8.8 months. The MR images were obtained with the fingers in extended and flexed positions using T2-weighted and T1-weighted sequences before and after intravenous injection of a gadolinium compound. Ten patients were treated surgically. Mean clinical follow-up was 1.8 years. Tears of the collateral ligaments were the most common lesion (30/39), most being radial in location. Contrast-enhanced axial T1-weighted images with the MCP joint in a flexed position showed these lesions optimally. Ten tears were partial and 20 were complete. In 13 patients, MR images showed 17 associated lesions including injuries of the extensor hood (10/17), interosseous tendon (3/17), palmar plate (3/17), and an osteochondral lesion (1/17). Sagittal MR images were essential to highlight palmar plate tears. Partial or complete tears of the collateral ligaments are prevalent MR imaging findings in patients with chronic disability resulting from injuries to the MCP joints. Although conservative treatment generally is sufficient for isolated injuries of the collateral ligaments, surgical repair is often required in cases of more extensive injuries. MR imaging may clearly delineate associated lesions of and about the MCP joints. (orig.)

  15. Irradiation stability of welded joints

    International Nuclear Information System (INIS)

    Results are presented of investigations into the neutron irradiation stability of welded joints in two types of steel used for reactor pressure vessels. Details are given of the materials used, method of welding and tests applied. The effect of irradiation on the notch toughness transition curve is shown. The results of the studies into irradiation embrittlement of all the welded joints and parent materials of the steels for the pressure vessels are summarized. (U.K.)

  16. Shell Joint Venture IT Framework

    OpenAIRE

    Evert Ruijs

    2013-01-01

    Dit artikel is alleen beschikbaar in het Nederlands. Shell's wereldwijde productie van olie en gas gaat voor een groot deel via Joint Ventures. Deze Joint Ventures werken in meer of mindere mate onder het management van Shell, vaak optioneel gebruik makend van Shell's processen, standaarden, gemeenschappelijke portfolio van applicaties en technologie. Om de vele soorten van applicaties en versies van implementaties beheersbaar te houden in de 'extended enterprise' is een goed raamwerk nodig. ...

  17. Asymptotic Analysis of the Load Transfer on Double-Lap Bolted Joints

    OpenAIRE

    KRATOCHVIL, Jan

    2012-01-01

    In this thesis, the complex potential method along with the method of compound asymptotic expansions is applied to the analysis of selected problems of plane elasticity related to double-lap bolted joints. The contribution to the thesis lies in the construction of several closed-form approximations of solutions to the considered problems. After a brief introduction of the basic theoretical concepts in Chapter 2, a mathematical model of a double-lap bolted joint is presented in Chapter 3....

  18. Joint between metals and PTFE

    International Nuclear Information System (INIS)

    Requirements to join dissimilar materials are more frequent in new technologies. The paper deals with a study of a joint between aluminium pieces and PTFE (teflon) pieces. The way of their joining is described. The joint was performed by soldering with adhesive 'x60', that covered the joining surfaces of the pieces, processed at a certain roughness, in a well established thickness layer. Initially, the surface of PTFE pieces were covered with a thin and uniform sodium metal sheet. The joint was realized by a particular procedure of soldering, simultaneously with plastic deformation of the metal. Various tests of the joint were carried out under conditions simulating service conditions. A piece joint was tested for its strength, thermal resistance and tightness. The tests showed a very good tightness of the joint at high vacuum (10-9 torr), in conditions of repeated thermic shocks, for temperature range within 73 K and 543 K. It was also study the interfaces between metal and PTFE. The study took into account the requirements of particular tests and relevant foreign standards, including ASTM and DIN. (authors)

  19. The effect evaluation of minoxidil tincture of joint compound glycyrrhizic on alopecia areata and the influence on serum TNF-α, TGF-β1 and of IL-12%米诺地尔酊联合复方甘草酸苷治疗斑秃疗效评价及对血清TNF-α、TGF-β1和IL-12的影响

    Institute of Scientific and Technical Information of China (English)

    陈玉华

    2015-01-01

    目的:评价米诺地尔酊联合复方甘草酸苷治疗斑秃疗效及对血清TNF-α、TGF-β1和IL-12的影响。方法:回顾性选取2011年5月至2014年1月我院收治的斑秃患者共658例,运用随机数表法选取给予米诺地尔酊联合复方甘草酸苷片(55例)作为研究组和同期单纯给予复方酸草苷片作为对照组(55例),每组患者均持续给予治疗3个月,治疗前后观察两组疗效、SALT评分及血清TNF-α、TGF-β1、IL-12的水平。结果:治疗后对照组总有效率显著低于研究组,两组差异有统计学意义(χ2=8.565,P=0.000);治疗后两组SALT评分均明显降低(P=0.000),但研究组明显低于对照组,差异有显著性(P=0.000);治疗后对照组TNF-α、TGF-β1水平明显高于研究组,IL-12水平明显低于研究组,差异有显著性(P=0.035、0.006、0.000);组内比较,治疗后两组TNF-α和IL-12水平均明显降低,TGF-β1水平明显升高,差异有显著性(P<0.05);两组不良反应发生率差异无显著性。结论:米诺地尔酊联合复方甘草酸苷治疗斑秃安全有效,可以调节斑秃患者血清细胞因子,改善毛发生长情况,值得临床推广。%Objective: To evaluate therapeutic effect of minoxidil tincture of joint compound glycyrrhizic on alopecia areata and the inlfuence on the serum TNF-α, TGF-β1 and IL-12.Methods:A total of 658 cases with alopecia areata were selected from May 2011 to January 2014 for retrospective study, and randomly divided into research group (55 cases) and control group (55 cases) using the random number table method. hTe research group was given minoxidil tincture joint compound glycyrrhizin, and the control group was given compound glycyrrhizin tablets, being treated for 3 months. Observe the SALT score before and atfer treatment serum TNF-α TGF-β1 and IL-2 levels were observed, the curative effect were evaluated.Results: Atfer treatment the total effective rate of

  20. 12 CFR 347.107 - Joint ventures.

    Science.gov (United States)

    2010-01-01

    ... or holds an equity interest in a foreign organization that is a joint venture, and the bank or its... under § 347.105(b). (b) Joint venture defined. For purposes of this section, the term “joint venture... 12 Banks and Banking 4 2010-01-01 2010-01-01 false Joint ventures. 347.107 Section 347.107...

  1. Management of acromioclavicular joint injuries.

    Science.gov (United States)

    Li, Xinning; Ma, Richard; Bedi, Asheesh; Dines, David M; Altchek, David W; Dines, Joshua S

    2014-01-01

    Acromioclavicular joint injuries are among the most common shoulder girdle injuries in athletes and most commonly result from a direct force to the acromion with the arm in an adducted position. Acromioclavicular joint injuries often present with associated injuries to the glenohumeral joint, including an increased incidence of superior labrum anterior posterior (SLAP) tears that may warrant further evaluation and treatment. Anteroposterior stability of the acromioclavicular joint is conferred by the capsule and acromioclavicular ligaments, of which the posterior and superior ligaments are the strongest. Superior-inferior stability is maintained by the coracoclavicular (conoid and trapezoid) ligaments. Type-I or type-II acromioclavicular joint injuries have been treated with sling immobilization, early shoulder motion, and physical therapy, with favorable outcomes. Return to activity can occur when normal shoulder motion and strength are obtained and the shoulder is asymptomatic as compared with the contralateral normal extremity. The management of type-III injuries remains controversial and is individualized. While a return to the previous level of functional activity with nonsurgical treatment has been documented in a number of case series, surgical reduction and coracoclavicular ligament reconstruction has been associated with a favorable outcome and can be considered in patients who place high functional demands on their shoulders or in athletes who participate in overhead sports. Surgical management is indicated for high-grade (≥type IV) acromioclavicular joint injuries to achieve anatomic reduction of the acromioclavicular joint, reconstruction of the coracoclavicular ligaments, and repair of the deltotrapezial fascia. Outcomes after surgical reconstruction of the coracoclavicular ligaments have been satisfactory with regard to achieving pain relief and return to functional activities, but further improvements in the biomechanical strength of these

  2. Migrating bone shards in dissecting Charcot joints.

    Science.gov (United States)

    Forrester, D M; Magre, G

    1978-06-01

    Extensive periarticular calcification is characteristic of Charcot joints. Fragmentation of the articular margins of bone contributes to the bony detritus, but the majority forms de novo in the joint capsule. Occasionally the calcific debris is seen far removed from the joint. Dissection of a chronically distended joint along muscle planes is most commonly associated with the inflammatory joint disease of rheumatoid arthritis. Its occurrence in Charcot joints is documented by arthrography, which demonstrates continuity of the joint space and the distant calcifications. PMID:418652

  3. Lead Free Solder Joint Thermal Condition in Semiconductor Packaging

    Directory of Open Access Journals (Sweden)

    M. N. Harif

    2010-01-01

    Full Text Available Problem statement: Solder joints are responsible for both electrical and mechanical connections. Solder does not have adequate ductility to ensure the repeated relative displacements due to the mismatch between expansion coefficients of the chip carrier and the circuit board. Solder material plays a crucial role to provide the necessary electrical and mechanical interconnections in an electronic assembly. Finding a technique to increase the service life of future connections is not the total solution. A method must be developed for predicting the remaining service life of many joints already in use. Approach: The effect of High Temperature Storage (HTS on lead free solder joint material for ball grid array application using pull test method is studied in this study. Some statistical analysis base on the pull test data also discussed. Three samples of different lead free solder joint material were selected in this experiment namely Sn3.8Ag0.7Cu (SAC387, Sn2.3Ag0.08Ni0.01Co (SANC and Sn3.5Ag. After the thermal condition test, all the lead free solder joint material samples were tested using Dage 4000 pull test machine. Each pull test will be 5 units and each unit contains 8 balls. Results: The mean pull strength for high temperature storage is 2847.66, 2628.20 and 2613.79 g for Sn3.5Ag, SANC and SAC387, respectively. Thus, Sn3.5Ag shows a significantly better solder joint performance in terms of joint strength compare to SANC and SAC387. Hence, Intermetallic Compound (IMC thicknesses were measured after cross-sectioning. Sample size for cross-sectioning was 3 units per read point, 2 balls per unit and 3 maximum IMC peaks per ball and the measurement using high power scope of 100x and Image Analyzer software to measure the IMC thickness. For high temperature storage, result show that the mean IMC thicknesses for SAC387, SANC and Sn3.5Ag are 3.9139, 2.3111 and 2.3931 µm. Conclusion/Recommendations: It was found that IMC thickness for SANC and Sn3

  4. Leaving a joint audit system

    DEFF Research Database (Denmark)

    Holm, Claus; Thinggaard, Frank

    2014-01-01

    Purpose: The authors aim to exploit a natural experment in which voluntary replace mandatory joint audits for Danish listed companies and analyse audit fee implications of using one or two audit firms. Design/methodology/approach: Regression analysis is used. The authors apply both a core audit fee...... determinants model and an audit fee change model and include interaction terms. Findings: The authors find short-term fee reductions in companies switching to single audits, but only where the former joint audit contained a dominant auditor. The authors argue that in this situation bargaining power is more...... with the auditors than in a equally shared joint audit, and that the auditors' incentives to offer an initial fee discount are bigger. Research limitations/implications: The number of observations is constrained by the small Danish capital market. Future research could take a more qualitative research...

  5. Goniometry in limited joint mobility

    Directory of Open Access Journals (Sweden)

    S Gopinath

    2012-01-01

    Full Text Available Aim: To study about the utility of goniometry in screening for limited joint mobility (LJM in patients attending a secondary level Diabetic Clinic. Materials and Methods: Randomly selected data of 100 patients attending a secondary level diabetic clinic without any complications were used. Baseline neuropathy assessments, namely monofilament and biothesiometry were done. Range of movement around the ankle joint and 1 st metatarsal joint was done using goniometry. Both the results were compared. Inclusion Criteria: Selected 100 patients attending a secondary level diabetic clinic and on regular follow-up were included in the study. Exclusion Criteria: Sick patients requiring parenteral feeds, IV antibiotics, co-morbid conditions such as microvascular complication, autonomic gastroparesis, and diabetic foot infections were excluded from the study. Conclusion: Goniometric screening for LJM is a cheap and effective screening tool for detecting early structural deformity producing a higher plantar pressure and ulcer, and thereby preventing them at early stage.

  6. Joint US/German Conference

    CERN Document Server

    Gulledge, Thomas; Jones, Albert

    1993-01-01

    This proceedings volume contains selected and refereed contributions that were presented at the conference on "Recent Developments and New Perspectives of Operations Research in the Area of Production Planning and Control" in Hagen/Germany, 25. - 26. June 1992. This conference was organized with the cooperation of the FernuniversiHit Hagen and was jointly hosted by the "Deutsche Gesellschaft fur Operations Research (DGOR)" and the "Manufacturing Special Interest Group of the Operations Research Society of America (ORSA-SIGMA)". For the organization of the conference we received generous financial support from the sponsors listed at the end of this volume. We wish to express our appreciation to all supporters for their contributions. This conference was the successor of the JOInt ORSA/DGOR-conference in Gaithersburg/Maryland, USA, on the 30. and 31. July 1991. Both OR-societies committed themselves in 1989 to host joint conferences on special topics of interest from the field of operations research. This goal ...

  7. Denervation of the wrist joint.

    Science.gov (United States)

    Buck-Gramcko, D

    1977-01-01

    A collective review was made of the results of denervation of the wrist joint for painful restrictiorn of motion done in 313 patients and follow-up studies on 195 (average 4.1 years, ranging from 9 months to 14 years). Complete denervation was done in only 30, partial denervation in the others being done after testing with local anesthetic blocks. Sixty-nine of the patients retained a moble wrist without pain or with slight pain with heavy work. No evidence of Charcot-like joints was seen. Poorest results followed when the operation was done for sequelae of intra-articular fracture of the radius, fracture dislocations, unstable ligamentous support, joint surface destruction, or for those required to do heavy manual labor. Arthrodesis was done secondarily in nine patients. PMID:839055

  8. Rheumatoid arthritis affecting temporomandibular joint

    Directory of Open Access Journals (Sweden)

    Amandeep Sodhi

    2015-01-01

    Full Text Available Rheumatoid arthritis (RA is a chronic, systemic, autoimmune inflammatory disorder that is characterized by joint inflammation, erosive properties and symmetric multiple joint involvement. Temporomandibular joint (TMJ is very rare to be affected in the early phase of the disease, thus posing diagnostic challenges for the dentist. Conventional radiographs fail to show the early lesions due to its limitations. More recently cone-beam computed tomography (CBCT has been found to diagnose the early degenerative changes of TMJ and hence aid in the diagnosis of the lesions more accurately. Our case highlights the involvement of TMJ in RA and the role of advanced imaging (CBCT in diagnosing the bony changes in the early phase of the disease.

  9. Torsion testing of bed joints

    DEFF Research Database (Denmark)

    Hansen, Klavs Feilberg; Pedersen, Carsten Mørk

    2008-01-01

    This paper describes a simple test method for determining the torsion strength of a single bed joint between two bricks and presents results from testing using this test method. The setup for the torsion test is well defined, require minimal preparation of the test specimen and the test can be...... carried out directly in a normal testing machine. The torsion strength is believed to be the most important parameter in out-of-plane resistance of masonry walls subjected to bending about an axis perpendicular to the bed joints. The paper also contains a few test results from bending of small walls about...... an axis perpendicular to the bed joints, which indicate the close connection between these results and results from torsion tests. These characteristics make the torsion strength well suited to act as substitute parameter for the bending strength of masonry about an axis perpendicular to the bed...

  10. Synthesis Organic Compound

    OpenAIRE

    Rasyid, Herlina; Firdaus; Hariani, Nunuk

    2015-01-01

    Abstract. Synthesis of metil ??-(p-hidroksifenil)akrilic from ??-(p-hidroksifenil)akrilat acid and methanol using Dean Stark Trap method had been done. Synthesis of ths compound intended to form the starting material in the subsequent synthesis of amide???s compound through the formation of ester compound. This synthesis using H2SO4 catalyst and Dean Stark Trap method, some of benzena which is added to remove the water that resulting from the reaction. Synthesis of this compound be held at re...

  11. On labelled compounds nomenclature

    International Nuclear Information System (INIS)

    Different approaches of major labelled compounds producers to their nomenclature in technical and commercial documentation are discussed. Some draft options of a standard technical guide document for labelled compounds nomenclature rules are suggested. Such a document after due discussion by the experts will serve to unification of the labelled compounds nomenclature within the frame of the CMEA member-countries co-operation in this field. The suggested options are based on the general recommendations by the International Union of Pure and Applied Chemistry and incorporate some more accurate definitions originating from the labelled compounds production and application experience

  12. Dual joint space arthrography in temporomandibular joint disorders: Comparison with single inferior joint space arthrography

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Hyung Sik; Chang, Duk Soo; Lee, Kyung Soo; Kim, Woo Sun; Sung, Jung Ho; Jun, Young Hwan [Capital Armed Forces General Hospital, Seoul (Korea, Republic of)

    1989-02-15

    The temporomandibular joint(TMJ) is really a complex of two synovial space separated by fibrocartilaginous disc. Single inferior joint space arthrography is commonly performed for evaluation of TMJ disorders, which is known to be superior in demonstrating joint dynamics. But it reveals only the inferior surface of the disc. Therefore, dual space arthrography is superior to demonstrate the soft tissue anatomic feature of the joint such as disc position and shape. Authors performed 83 TMJ arthrograms in TMJ problems. Initially, the inferior joint space was done and then the superior space was sequentially contrasted. The follow results were noted: 1. In all cases, dual space arthrography revealed accurate disc shape and positions. 2. Concordant findings between the two techniques: 68 cases (82%). Discordance between the two techniques: 15 cases (18%) 3. Possible causes of discordance between inferior and dual space arthrography. a) Normal varians of anterior recess: 3 cases b) Posterior disc displacement: 4 cases c) Influence of the patient's head position change :4 cases d) False perforation: 2 cases e) Reduction change: 2 cases 4. In 5 cases with anterior displacement, dual space arthrography gave additional findings such as adhesion within the superior space, which could not be evaluated by single inferior space.

  13. Dual joint space arthrography in temporomandibular joint disorders: Comparison with single inferior joint space arthrography

    International Nuclear Information System (INIS)

    The temporomandibular joint(TMJ) is really a complex of two synovial space separated by fibrocartilaginous disc. Single inferior joint space arthrography is commonly performed for evaluation of TMJ disorders, which is known to be superior in demonstrating joint dynamics. But it reveals only the inferior surface of the disc. Therefore, dual space arthrography is superior to demonstrate the soft tissue anatomic feature of the joint such as disc position and shape. Authors performed 83 TMJ arthrograms in TMJ problems. Initially, the inferior joint space was done and then the superior space was sequentially contrasted. The follow results were noted: 1. In all cases, dual space arthrography revealed accurate disc shape and positions. 2. Concordant findings between the two techniques: 68 cases (82%). Discordance between the two techniques: 15 cases (18%) 3. Possible causes of discordance between inferior and dual space arthrography. a) Normal varians of anterior recess: 3 cases b) Posterior disc displacement: 4 cases c) Influence of the patient's head position change :4 cases d) False perforation: 2 cases e) Reduction change: 2 cases 4. In 5 cases with anterior displacement, dual space arthrography gave additional findings such as adhesion within the superior space, which could not be evaluated by single inferior space

  14. Microstructural Evolution of Lead-Free Solder Joints in Ultrasonic-Assisted Soldering

    Science.gov (United States)

    Ji, Hongjun; Wang, Qiang; Li, Mingyu

    2016-01-01

    Solder joint reliability greatly depends on the microstructure of the solder matrix and the morphology of intermetallic compounds (IMCs) in the joints. Addition of strengthening phases such as carbon nanotubes and ceramic particles to solder joints to improve their properties has been widely studied. In this work, ultrasonic vibration (USV) of casting ingots was applied to considerably improve their microstructure and properties, and the resulting influence on fluxless soldering of Cu/Sn-3.0Ag-0.5Cu/Cu joints and their microstructural evolution was investigated. It was demonstrated that USV application during reflow of Sn-based solder had favorable effects on β-Sn grain size refinement as well as the growth and distribution of various IMC phases within the joints. The β-Sn grain size was significantly refined as the ultrasound power was increased, with a reduction of almost 90% from more than 100 μm to below 10 μm. Long and large Cu6Sn5 tubes in the solder matrix of the joints were broken into tiny ones. Needle-shaped Ag3Sn was transformed into flake-shaped. These IMCs were mainly precipitated along β-Sn phase boundaries. High-temperature storage tests indicated that the growth rate of interfacial IMCs in joints formed with USV was slower than in conventional reflow joints. The mechanisms of grain refinement and IMC fragmentation are discussed and related to the ultrasonic effects.

  15. Prosthesis of the wrist-joint

    Energy Technology Data Exchange (ETDEWEB)

    Feldmeier, C.

    1983-02-25

    Function of the hand-joint and the well-being of patients can be severely affected by arthrosis of the wrist-joint. Therapeutically, arthrodesis usually results in a painfree status of stiffness. A painless and well functioning joint can be achieved by alloplastic joint replacement or resurfacing. The possibilities and clinical results in cases of arthrosis of the carpo-metacarpal joint of the thumb, pseudarthrosis of the scaphoid, aseptic necrosis of the Lunate and severe arthrosis of the radio-carpal joint are demonstrated.

  16. Prosthesis of the wrist-joint

    International Nuclear Information System (INIS)

    Function of the hand-joint and the well-being of patients can be severely affected by arthrosis of the wrist-joint. Therapeutically, arthrodesis usually results in a painfree status of stiffness. A painless and well functioning joint can be achieved by alloplastic joint replacement or resurfacing. The possibilities and clinical results in cases of arthrosis of the carpo-metacarpal joint of the thumb, pseudarthrosis of the scaphoid, aseptic necrosis of the Lunate and severe arthrosis of the radio-carpal joint are demonstrated. (orig.)

  17. Complex motion tomography of the sacroiliac joint

    International Nuclear Information System (INIS)

    To find a better method for diagnosing sacroiliac (SI) joint disease, an anatomical approach was combined with conventional roentgenology, complex motion tomography and computed tomography. Complex motion tomography is suggested as the method of choice in the investigation of the SI-joint. Because of its complex (sinusoidal) form, the dorsal portion of the joint has to be tomographed in frontal projection and the middle and ventral portions in oblique projection. In 56 patients, referred for probable ankylosing spondylitis, 72 SI joints were investigated. Based on plain radiography six and on frontal tomography five SI joints were diagnosed as normal. However, based on oblique tomography 31 joints were diagnosed as normal. (orig.)

  18. NATURAL POLYACETYLENE COMPOUNDS

    Directory of Open Access Journals (Sweden)

    D. A. Konovalov

    2014-01-01

    Full Text Available Polyacetylenes (polyynes are compounds which contain two or more triple bonds in its structure. About 2 000 different polyacetylenes and biogenetically related substances were identified in 24 families of higher plants. However, most of these compounds were found in seven families of flowering plants: Apiaceae (Umbelliferae, Araliaceae, Asteraceae (Compositae, Campanulaceae, Olacaceae, Pittosporaceae and Santalaceae. Polyacetylenes are relatively unstable, chemically and biologically active compounds, and present in fungi, microorganisms, marine invertebrates and other organisms except for plants. Acetylenes form distinct specialized group of chemically active natural compounds, which are biosynthesized in plants of unsaturated fatty acids. In addition to widespread aliphatic polyacetylenes thiophenes dithiacyclohexadienes (thiarubrines, thioethers, sulphoxides, sulphones, alkamides, chlorohydrins, lactones, spiroacetal enol ethers, furans, pyrans, tetrahydropyrans, isocoumarins, aromatic acetylenes were also found in plant species. Polyacetylenes are localized in different plant organs, and can be found both individually and as a compound with carbohydrates, terpene, phenolic and other compounds. Many polyacetylenes are found in the composition of the essential oils of plants and it confirms their strongly marked ecological functions. From biological point of view these compounds are often synthesized by plants as toxic or bitter antifeedants, allelopathic compounds, phytoalexins or broadly antibiotic components. Polyynes are strong photosensitizers. They exhibit anti-inflammatory, anti-coagulant, anti-bacterial, antituberculosis, anti-fungal, anti-viral, neuroprotective and neurotoxic activity. Immunostimulatory influence associated with certain allergenicity of some of these substances was established. Therefore, without a doubt polyacetylenes are of interest for the modern pharmacy and medicine.

  19. Stable isotopes labelled compounds

    International Nuclear Information System (INIS)

    The catalogue on stable isotopes labelled compounds offers deuterium, nitrogen-15, and multiply labelled compounds. It includes: (1) conditions of sale and delivery, (2) the application of stable isotopes, (3) technical information, (4) product specifications, and (5) the complete delivery programme

  20. NATURAL POLYACETYLENE COMPOUNDS

    OpenAIRE

    D. A. Konovalov

    2014-01-01

    Polyacetylenes (polyynes) are compounds which contain two or more triple bonds in its structure. About 2 000 different polyacetylenes and biogenetically related substances were identified in 24 families of higher plants. However, most of these compounds were found in seven families of flowering plants: Apiaceae (Umbelliferae), Araliaceae, Asteraceae (Compositae), Campanulaceae, Olacaceae, Pittosporaceae and Santalaceae. Polyacetylenes are relatively unstable, chemically and biologically activ...

  1. What Determines Joint Venture Termination?

    DEFF Research Database (Denmark)

    Nielsen, Bo Bernhard

    2012-01-01

    Joint venture (JV) research continues to flourish as researchers seek to advance our understanding of why so many JVs fail. Cui and Kumar (this issue) take a contingency approach to explain how and why business relatedness may provide new insights as to what determines JV termination. This...

  2. Joint Attention and Anthropological Difference

    Czech Academy of Sciences Publication Activity Database

    Urban, Petr

    2014-01-01

    Roč. 11, č. 1 (2014), s. 59-70. ISSN 1718-0198 R&D Projects: GA ČR GAP401/10/1164 Institutional support: RVO:67985955 Keywords : joint attention * anthropological difference * phenomenology * great apes * shared intentionality Subject RIV: AA - Philosophy ; Religion

  3. Joint energy program makes progress

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ "Clean Energies Facing the Future," a cooperative research program jointly organized by CAS and the BP Group, has made encouraging progress, say experts at an annual sum-up workshop held on 31 July and I August at Tsinghua University in Beijing. The CAS Dalian Institute of Chemical Physics(DICP) has been entrusted as coordinator of the cooperative program between the two sides.

  4. Imaging of hip joint arthroplasty

    International Nuclear Information System (INIS)

    The hip joint is the largest joint in the human body and consequently, its evaluation by diagnostic imaging is highly important. This includes imaging of hip joint arthroplasty, which is used to avoid joint immobility following a wide spectrum of diseases, such as end-stage degenerative disease, avascular necrosis of the femoral head or post-traumatic fractures. Conventional radiography is still the standard imaging modality for the evaluation of hip arthroplasty both directly following surgery and for periodical follow-up. In the majority of cases conventional radiography enables adequate assessment of early and late complications that can arise following hip arthroplasty, such as loosening, prosthetic or periprosthetic fracture, luxation, infection and soft tissue calcification. If the diagnosis cannot be established by means of radiography, advanced imaging methods such as computed tomography (CT) and magnetic resonance imaging (MRI), with or without injection of contrast media, may provide additional information. This is particularly true for the depiction of inflammatory processes. Regardless of the imaging modality used patients' clinical symptoms must also be taken into account in order to establish the correct diagnosis. (orig.)

  5. Nomenclature for labelled compounds

    International Nuclear Information System (INIS)

    This paper report on isotopically labelled compounds. The first indexing system for isotopically labelled organic compounds is generally credited to Boughton and named after him. An extension of his principles for designating compounds containing hydrogen isotopes has been part of the Chemical Abstracts Service index nomenclature system for many years. After close on five years labor the IUPAC sponsored Commission on Nomenclature of Organic Chemistry presented in 1979 their findings on Isotopically Modified Compounds. The system codified in their rules provides for recognition of various types of isotopic modification and is therefore of more general applicability. Concurrently the rules for the nomenclature of isotopically modified inorganic compounds are developed. These are to be seen as supplementing and extending the guidelines laid down in the IUPAC Inorganic Nomenclature Rules already published

  6. Biokinetics of radioactive compounds

    International Nuclear Information System (INIS)

    Biokinetics of radioactive compounds in the human organism represent the central notion in this work, consisting of a theoretical and an experimental part. The first chapter contains definitions and explanations on the importance of the biokinetics of radioactive compounds in clinical therapy and pharmaceuticals research as well as for assessing radiation exposure and radiation hazards. Chapter 2 describes the bases of the biokinetics of radioactive compounds in the medical and non-medical sector, and biokinetics. Chapter 3 deals with obtaining biokinetics data for radioactive compounds from investigations in animals and man, evaluation of measurements, transferring data obtained by animal experiments to man, and with the variability of biokinetics data. In Chapter 4 the results of comprehensive studies in literature on the biokinetics of radioactive compounds are summarized. They relate to three areas: professional and environmental incorporation of radioactive compounds, use of radioactive pharmaceuticals in therapy and research, and incorporation of radioactive compounds by embryo and fetus in consequence of the uptake of radioactive compounds by the mother. Chapter 5 gives an assessment of radiation hazards from radioactive compounds in connection with occupational radiation exposure and nuclear diagnostics in vivo, and a comparison with other risks. For that purpose the concept of effective dose equivalent is applied in connection with suitable risk coefficients to professional and nuclear-medical radiation exposure. Chapter 6 is dedicated to measurement of the biokinetics of radioactive compounds in man using conventional devices. The object of Chapter 7 is measurement of the biokinetics of radioactive pharmaceuticals in man by means of single photon emission computed tomography. (orig./MG)

  7. Records and record-keeping for the hospital compounding pharmacist.

    Science.gov (United States)

    McElhiney, Linda F

    2007-01-01

    The United States Pharmacopeial Convention, Inc., is recognized by federal law and by most state boards of pharmacy as the official group for setting the standards for pharmaceuticals and pharmacy practice, including compounding. The standards of United States Pharmacopeia Chapter 795 require that a pharmacy maintain records on a compounded preparation, including the formulation record, and a Material Safety Data Sheets file. The American Society of Health-Systems Pharmacists' guidelines require that hospital pharmacy departments maintain at least four sets of records in the compounding area: (1) compounding formulas and procedures, (2) compounding logs of all compounded preparations, including batch records and sample batch labels, (3) equipment maintenance records, and (4) a record of ingredients purchased, including cerificates of analysis and Material Saftey Data Sheets. Hospital compounding records may be inspected by any of several outside organizations, including state boards of pharmacy, third-party payers, the Joint Commission on Accreditaion of Healthcare Organizations, the Drug Enforcement Agency, and attorneys. With the existing standards and guidelines in place and the importance of documentation unquestionable, a record of pharmacy activites should be maintained in a compounding pharmacy so that preparations can be replicated consistently, the history of each ingredient traced, equipment maintenance and calibration verified, and compounding procedures evaluated easily. PMID:23974620

  8. Business process solution `Joint MEISTER`; Gyomu shien solution `Joint MEISTER`

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, Y.; Ito, S. [Fuji Electric Co. Ltd., Tokyo (Japan)

    1998-12-10

    The business process solution `Joint{sub M}EISTER` can be ranked among computer systems represented by groupware and WWW applications. This paper describes its typical system, ExchangeUSE work flow solution, and the effect of its introduction, citing a concrete case. The Company A introduced the ExchangeUSE work flow for traveling expenses adjustment and attendance, and has gained a reduction of 7 man-months/month. (author)

  9. Cancer of the Bone and Joint

    Science.gov (United States)

    ... a third party. HPF: SEER Stat Fact Sheets: Bone and Joint Cancer Expand All Collapse All Lifetime risk estimates are ... 5 Years Or More after Being Diagnosed with Bone and Joint Cancer? Relative survival statistics compare the survival of patients ...

  10. Improvements in or relating to pipe joints

    International Nuclear Information System (INIS)

    Pipe joints are described that are particularly suitable for liquid metal cooled nuclear reactors. The object is to provide a joint capable of accommodating movements resulting from differential expansion of the reactor components. Full constructional details are given. (UK)

  11. Joint structure in high brightness light emitting diode (HB LED) packages

    International Nuclear Information System (INIS)

    We present the transmission electron microscopy (TEM) analysis of 1.5 μm-thick Au-20Sn solder joint between a high brightness light emitting diode (HB LED) and a Si heat sink. Due to intermetallic compound formation, global Sn depletion occurred in the thin solder, which raised the melting point of the solder and caused local incompleteness of bonding

  12. Microstructures and properties of tungsten inert gas welding joint of super-eutectic ZA alloy

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The microstructure of butt-welding joint of supper-eutectic ZA alloy in TIG welding was analyzed through optical microscope and transmission electronic microscope. The results show that the weld seam microstructure is fine and mainly composed of columnar crystals and minor equiaxed crystals, the microstructure in the zone near the weld seam is coarse columnar crystals, and the grain in heat-affected zone does not grow markedly. The joint microstructure at room temperature is consisted of β phase (rich Al), η-Zn, ε phase (CuZn compound), Al4Cu9 and other compounds. The hardness of the weld bond area and the tensile strength of the joint are a little higher than that of base materials. The specific elongation of the weld and bond area is a little lower than those of base materials.

  13. Seismic response of rock joints and jointed rock mass

    International Nuclear Information System (INIS)

    Long-term stability of emplacement drifts and potential near-field fluid flow resulting from coupled effects are among the concerns for safe disposal of high-level nuclear waste (HLW). A number of factors can induce drift instability or change the near-field flow patterns. Repetitive seismic loads from earthquakes and thermal loads generated by the decay of emplaced waste are two significant factors. One of two key technical uncertainties (KTU) that can potentially pose a high risk of noncompliance with the performance objectives of 10 CFR Part 60 is the prediction of thermal-mechanical (including repetitive seismic load) effects on stability of emplacement drifts and the engineered barrier system. The second KTU of concern is the prediction of thermal-mechanical-hydrological (including repetitive seismic load) effects on the host rock surrounding the engineered barrier system. The Rock Mechanics research project being conducted at the Center for Nuclear Waste Regulatory Analyses (CNWRA) is intended to address certain specific technical issues associated with these two KTUs. This research project has two major components: (i) seismic response of rock joints and a jointed rock mass and (ii) coupled thermal-mechanical-hydrological (TMH) response of a jointed rock mass surrounding the engineered barrier system (EBS). This final report summarizes the research activities concerned with the repetitive seismic load aspect of both these KTUs

  14. Seismic response of rock joints and jointed rock mass

    Energy Technology Data Exchange (ETDEWEB)

    Ghosh, A.; Hsiung, S.M.; Chowdhury, A.H. [Southwest Research Inst., San Antonio, TX (United States). Center for Nuclear Waste Regulatory Analyses

    1996-06-01

    Long-term stability of emplacement drifts and potential near-field fluid flow resulting from coupled effects are among the concerns for safe disposal of high-level nuclear waste (HLW). A number of factors can induce drift instability or change the near-field flow patterns. Repetitive seismic loads from earthquakes and thermal loads generated by the decay of emplaced waste are two significant factors. One of two key technical uncertainties (KTU) that can potentially pose a high risk of noncompliance with the performance objectives of 10 CFR Part 60 is the prediction of thermal-mechanical (including repetitive seismic load) effects on stability of emplacement drifts and the engineered barrier system. The second KTU of concern is the prediction of thermal-mechanical-hydrological (including repetitive seismic load) effects on the host rock surrounding the engineered barrier system. The Rock Mechanics research project being conducted at the Center for Nuclear Waste Regulatory Analyses (CNWRA) is intended to address certain specific technical issues associated with these two KTUs. This research project has two major components: (i) seismic response of rock joints and a jointed rock mass and (ii) coupled thermal-mechanical-hydrological (TMH) response of a jointed rock mass surrounding the engineered barrier system (EBS). This final report summarizes the research activities concerned with the repetitive seismic load aspect of both these KTUs.

  15. Snap Joint Technology for Composite Structures

    OpenAIRE

    ECT Team, Purdue

    2007-01-01

    The optimum composite joint design is the one capable of distributing stresses over a wide area rather than to concentrate them at a point. Adhesively bonded joints can satisfy these requirements, however, most of the adhesives are brittle, and brittle failure is unavoidable. This was the motivation of developing what is called the SNAP joint. The snap joint technology developed by W. Brandt Goldworthy & Associates, Inc. The concept is based on similar joining technology used for connecting w...

  16. Price elasticities, joint products, and international trade

    OpenAIRE

    Piggott, Nicholas E.; Wohlgenant, Michael K.

    2002-01-01

    This paper extends the basic results of Houck’s insight for derived demand elasticities for the case of joint products by allowing for the possibility of the joint and raw products being traded. Theoretical relationships between individual demands for a set of jointly-produced commodities that are traded and composite demand for the raw product from which the joint products originate are derived. It is shown that while the derived price elasticity of domestic demand retains the same form as H...

  17. Limited joint mobility in diabetes mellitus.

    OpenAIRE

    Campbell, R R; Hawkins, S.J.; Maddison, P J; Reckless, J P

    1985-01-01

    The relationship of limited joint mobility and finger joint contractures in diabetics to age of onset, duration, and control of diabetes has not been established. We measured the mobility of metacarpophalangeal, wrist, elbow, and ankle joints and assessed the prevalence of finger joint contractures in 254 young diabetics and 110 controls. The presence of microvascular disease was assessed by ophthalmoscopy and urine analysis for proteinuria. An estimate of long-term diabetic control was obtai...

  18. Revolute joints with clearance in multibody systems

    OpenAIRE

    Flores, Paulo; Ambrósio, Jorge

    2004-01-01

    A computational methodology for dynamic analysis of multibody mechanical systems with joint clearance is presented in this work. Clearances always exist in real joints in order to ensure the correct relative motion between the connected bodies being the gap associated to them a result of machining tolerance, wear, and local deformations. Clearance at different joints is the source for impact forces, resulting in wear and tear of the joints, and consequently the degradation of the system perfo...

  19. Revamped, joint ventures make a comeback.

    Science.gov (United States)

    Peters, G R

    1991-08-01

    After a period of declining popularity, joint ventures are beginning to re-emerge as viable solution to challenges facing health care. Future joint ventures likely will be different, however, in response to problems and resulting legislation. Healthcare providers interested in starting a joint venture should consider five basic formats and some guidelines for developing them. Joint ventures ultimately may become a focal point for renewed efforts at regional healthcare planning. PMID:10145473

  20. Behaviour of high strength steel moment joints

    OpenAIRE

    Girão Coelho, A.M.; Bijlaard, F.S.K.

    2010-01-01

    The design of joints to European standard EN 1993 within the semi-continuous/partially restrained philosophy is restricted to steel grades up to S460. With the recent development of high performance steels, the need for these restrictions should be revisited. The semicontinuous joint modelling can be adopted as long as the joint develops rotation capacity and behaves ductile. The research summarized in this paper focuses on moment joints with components made from high strength steel S460, S69...

  1. Prognosis of motor development and joint hypermobility.

    OpenAIRE

    Tirosh, E; Jaffe, M; Marmur, R; Taub, Y; Rosenberg, Z.

    1991-01-01

    In a study of 59 infants aged 18 months there were 20 with joint hypermobility and delayed motor development, 19 with joint hypermobility and normal motor development, and 20 normal controls. They were reassessed for motor function 3.5 years later at the age of 5 years. Both gross and fine motor performance were significantly delayed in the group of children who exhibited joint hypermobility and motor delay in infancy. No significant delay was evident in those with joint hypermobility only. J...

  2. Adolescent obesity, joint pain, and hypermobility

    OpenAIRE

    Bout-Tabaku, Sharon; Klieger, Sarah B; Wrotniak, Brian H; Sherry, David D; Zemel, Babette S; Stettler, Nicolas

    2014-01-01

    Background Obesity associated with joint pain of the lower extremities is likely due to excessive mechanical load on weight bearing joints. Additional mechanical factors may explain the association between obesity and joint pain. Findings We characterized the association between obesity and non-traumatic lower extremity (LE) joint pain in adolescents and examined the modifying effect of hypermobility on this association. We performed a cross-sectional analysis of data from subjects enrolled i...

  3. Russian upstream joint ventures logging progress

    International Nuclear Information System (INIS)

    This paper reports that Occidental Petroleum Corp. has begun exporting oil from Russia as part of an enhanced recovery joint venture in western Siberia. Oxy holds a 50% interest in the joint venture company, Vanyoganneft, and will market the oil. In other activity, two Canadian companies are marking progress with Russian upstream joint ventures

  4. 22 CFR 228.34 - Joint ventures.

    Science.gov (United States)

    2010-04-01

    ... Financing § 228.34 Joint ventures. A joint venture or unincorporated association is eligible only if each of... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Joint ventures. 228.34 Section 228.34 Foreign Relations AGENCY FOR INTERNATIONAL DEVELOPMENT RULES ON SOURCE, ORIGIN AND NATIONALITY FOR COMMODITIES...

  5. Acupuncture Therapy on Temporomandibular Joint Syndrome

    Institute of Scientific and Technical Information of China (English)

    XIA Nai-nian; HUANG Ming-juan

    2005-01-01

    @@ Temporomandibular Joint (TMJ) syndrome, an commonly and frequently encountered disease, is characterized by motor dysfunction of mandibular joint and snapping articular surface as major complaints, and then tinnitus, facial pain and occasional headache, most patients got limited mouth open and pain inside the joints or masseter muscle. The authors of this article have treated 68cases of TMJ syndrome since 2001.

  6. Joint prosthesis and method of bone fixation

    NARCIS (Netherlands)

    Oosterom, R.; Van der Pijl, A.J; Bersee, H.E.N.; Van der Helm, F.C.; Herder, J.L

    2006-01-01

    The invention relates to a joint prosthesis (10), for example, a knee joint or shoulder joint prosthesis comprising a first, socket-holding prosthesis part (11) for attachment to a first bone (12) and a second, ball-holding prosthesis part (13) for attachment to a second bone (14) that intermates wi

  7. 49 CFR 234.233 - Rail joints.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Rail joints. 234.233 Section 234.233..., DEPARTMENT OF TRANSPORTATION GRADE CROSSING SIGNAL SYSTEM SAFETY AND STATE ACTION PLANS Maintenance, Inspection, and Testing Maintenance Standards § 234.233 Rail joints. Each non-insulated rail joint...

  8. 17 CFR 300.105 - Joint accounts.

    Science.gov (United States)

    2010-04-01

    ... 17 Commodity and Securities Exchanges 3 2010-04-01 2010-04-01 false Joint accounts. 300.105... A to Part 285 RULES OF THE SECURITIES INVESTOR PROTECTION CORPORATION Accounts of âseparateâ Customers of Sipc Members § 300.105 Joint accounts. (a) A joint account shall be deemed to be a...

  9. 21 CFR 26.73 - Joint Committee.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Joint Committee. 26.73 Section 26.73 Food and... OF PHARMACEUTICAL GOOD MANUFACTURING PRACTICE REPORTS, MEDICAL DEVICE QUALITY SYSTEM AUDIT REPORTS...Frameworkâ Provisions § 26.73 Joint Committee. (a) A Joint Committee consisting of representatives of...

  10. Chemical effect on diffusion in intermetallic compounds

    Science.gov (United States)

    Chen, Yi-Ting

    With the trend of big data and the Internet of things, we live in a world full of personal electronic devices and small electronic devices. In order to make the devices more powerful, advanced electronic packaging such as wafer level packaging or 3D IC packaging play an important role. Furthermore, ?-bumps, which connect silicon dies together with dimension less than 10 ?m, are crucial parts in advanced packaging. Owing to the dimension of ?-bumps, they transform into intermetallic compound from tin based solder after the liquid state bonding process. Moreover, many new reliability issues will occur in electronic packaging when the bonding materials change; in this case, we no longer have tin based solder joint, instead, we have intermetallic compound ?-bumps. Most of the potential reliability issues in intermetallic compounds are caused by the chemical reactions driven by atomic diffusion in the material; thus, to know the diffusivities of atoms inside a material is significant and can help us to further analyze the reliability issues. However, we are lacking these kinds of data in intermetallic compound because there are some problems if used traditional Darken's analysis. Therefore, we considered Wagner diffusivity in our system to solve the problems and applied the concept of chemical effect on diffusion by taking the advantage that large amount of energy will release when compounds formed. Moreover, by inventing the holes markers made by Focus ion beam (FIB), we can conduct the diffusion experiment and obtain the tracer diffusivities of atoms inside the intermetallic compound. We applied the technique on Ni3Sn4 and Cu3Sn, which are two of the most common materials in electronic packaging, and the tracer diffusivities are measured under several different temperatures; moreover, microstructure of the intermetallic compounds are investigated to ensure the diffusion environment. Additionally, the detail diffusion mechanism was also discussed in aspect of diffusion

  11. Interfacial Reactions and Joint Strengths of Sn- xZn Solders with Immersion Ag UBM

    Science.gov (United States)

    Jee, Y. K.; Yu, Jin

    2010-10-01

    The solder joint microstructures of immersion Ag with Sn- xZn ( x = 0 wt.%, 1 wt.%, 5 wt.%, and 9 wt.%) solders were analyzed and correlated with their drop impact reliability. Addition of 1 wt.% Zn to Sn did not change the interface microstructure and was only marginally effective. In comparison, the addition of 5 wt.% or 9 wt.% Zn formed layers of AgZn3/Ag5Zn8 at the solder joint interface, which increased drop reliability significantly. Under extensive aging, Ag-Zn intermetallic compounds (IMCs) transformed into Cu5Zn8 and Ag3Sn, and the drop impact resistance at the solder joints deteriorated up to a point. The beneficial role of Zn on immersion Ag pads was ascribed to the formation of Ag-Zn IMC layers, which were fairly resistant to the drop impact, and to the suppression of the brittle Cu6Sn5 phase at the joint interface.

  12. Wilmar joint market model, Documentation

    Energy Technology Data Exchange (ETDEWEB)

    Meibom, P.; Larsen, Helge V. [Risoe National Lab. (Denmark); Barth, R.; Brand, H. [IER, Univ. of Stuttgart (Germany); Weber, C.; Voll, O. [Univ. of Duisburg-Essen (Germany)

    2006-01-15

    The Wilmar Planning Tool is developed in the project Wind Power Integration in Liberalised Electricity Markets (WILMAR) supported by EU (Contract No. ENK5-CT-2002-00663). A User Shell implemented in an Excel workbook controls the Wilmar Planning Tool. All data are contained in Access databases that communicate with various sub-models through text files that are exported from or imported to the databases. The Joint Market Model (JMM) constitutes one of these sub-models. This report documents the Joint Market model (JMM). The documentation describes: 1. The file structure of the JMM. 2. The sets, parameters and variables in the JMM. 3. The equations in the JMM. 4. The looping structure in the JMM. (au)

  13. Wilmar joint market model, Documentation

    International Nuclear Information System (INIS)

    The Wilmar Planning Tool is developed in the project Wind Power Integration in Liberalised Electricity Markets (WILMAR) supported by EU (Contract No. ENK5-CT-2002-00663). A User Shell implemented in an Excel workbook controls the Wilmar Planning Tool. All data are contained in Access databases that communicate with various sub-models through text files that are exported from or imported to the databases. The Joint Market Model (JMM) constitutes one of these sub-models. This report documents the Joint Market model (JMM). The documentation describes: 1. The file structure of the JMM. 2. The sets, parameters and variables in the JMM. 3. The equations in the JMM. 4. The looping structure in the JMM. (au)

  14. Lipoma arborescens affecting multiple joints

    Energy Technology Data Exchange (ETDEWEB)

    Bejia, Ismail; Younes, Mohamed; Touzi, Mongi; Bergaoui, Naceur [EPS Monastir, Department of Rheumatology, Monastir (Tunisia); Moussa, Adnene [Faculty of Medicine of Monastir, Department of Anatomopathology, Monastir (Tunisia); Said, Mourad [EPS Monastir, Department of Radiology, Monastir (Tunisia)

    2005-09-01

    Lipoma arborescens is a rare benign intra-articular lesion of unknown etiology that usually involves the suprapatellar pouch of the knee joint. Clinically, the most common finding is a slow-growing painless swelling, accompanied by intermittent effusion of the joint. We report a case of a multifocal lipoma arborescens localized in the knees and the hips in a 24-year-old man, initially mimicking an inflammatory arthropathy. The diagnosis of lipoma arborescens was made by magnetic resonance imaging of the hips and the knees. Under arthroscopic guidance, the synovial biopsy of the right knee disclosed the specific histological signs of lipoma arborescens. As far as we know, this is the third case of multifocal lipoma arborescens reported in the English literature. (orig.)

  15. Hydrocolonotherapy ankle joints after injuries

    Directory of Open Access Journals (Sweden)

    Volodymyr Muchin

    2016-02-01

    Full Text Available Purpose: to improve efficiency of gydrokinesitherapy by means of specially designed devices and monolasts for patients after ankle joint injuries. Material & Methods: there are pedagogical methods, clinical and radiological methods, anthropometric measurements and goniometry were used. Results: the author's technique of hydrokinesitherapy with application hydrokinesimechanotherapy device in the program of physical rehabilitation which provides optimum conditions for the recovery process was developed. Conclusions: the specially designed hydrokinesomechanotherapeutic device and monolasts are allow strictly controlled movement in all planes of the ankle joint, which contributes to the acceleration of the recovery; the conducted anthropometric and goniometric studies were indicate more rapid elimination of edema, increase movement amplitude, carries opposition to the development of contractures and muscle atrophy.

  16. Afghanistan; Joint Staff Advisory Note

    OpenAIRE

    International Monetary Fund

    2010-01-01

    This Joint Staff Advisory Note discusses Afghanistan’s Poverty Reduction Strategy Paper's annual progress report. Afghanistan has experienced a number of extraordinary challenges that delayed its implementation. The security situation deteriorated markedly and has been dominated by the cross-border Taliban insurgency. Growth started to recover from a devastating drought. In May 2008, food and fuel prices peaked, leading to high inflation and pressure on the budget for additional fuel and fo...

  17. Electrochemical Corrosion of Adhesive Joints

    Czech Academy of Sciences Publication Activity Database

    Vondrák, Jiří

    Vol. 2. Brno: Akademické nakladatelství CERM, 2000 - (Vondrák, J.; Sedlaříková, M.), s. 10.1-10.2 ISBN 80-214-1615-7. [Advanced Batteries and Accumulators /1./. Brno (CZ), 28.08.2000-01.09.2000] Institutional research plan: CEZ:AV0Z4032918 Keywords : adhesive * joints * corrosion Subject RIV: CG - Electrochemistry

  18. Temporomandibular joint dysfunction in children

    OpenAIRE

    Fernanda Mara de Paiva BERTOLI; Estela Maris LOSSO; Ricardo César MORESCA

    2009-01-01

    Introduction and objective: The aim of this study was to review aspects related to the temporomandibular dysfunctions (TMD) in children,like etiology, diagnosis and treatment, emphasizing the importance of the correct diagnosis, since these patients are in their growth and development of the face period. Literature review: The TMDs include many clinical problems that involve the mastigatory muscles, the temporomandibular joint and near structures. In children the symptoms of this syndrome are...

  19. On joint numerical radius II

    Czech Academy of Sciences Publication Activity Database

    Drnovšek, R.; Müller, Vladimír

    2014-01-01

    Roč. 62, č. 9 (2014), s. 1197-1204. ISSN 0308-1087 R&D Projects: GA ČR GA201/09/0473; GA AV ČR IAA100190903 Institutional support: RVO:67985840 Keywords : joint numerical range * numerical radius Subject RIV: BA - General Mathematics Impact factor: 0.738, year: 2014 http://www.tandfonline.com/doi/abs/10.1080/03081087.2013.816303

  20. Joint Commission on rock properties

    Science.gov (United States)

    A joint commission on Rock Properties for Petroleum Engineers (RPPE) has been established by the International Society of Rock Mechanics and the Society of Petroleum Engineers to set up data banks on the properties of sedimentary rocks encountered during drilling. Computer-based data banks of complete rock properties will be organized for sandstones (GRESA), shales (ARSHA) and carbonates (CARCA). The commission hopes to access data sources from members of the commission, private companies and the public domain.

  1. Seabasing and joint expeditionary logistics

    OpenAIRE

    Bender, Amy; Cottle, Jacob; Craddock, Timothy; Dowd, Justin; Feese, Rick; Foster, Brett; Gainey, John; Jimenez, Ivan; Johnson, Brent; Johnson, Terry; Lemmon, John; Levendofske, Michael; Liskey, Dale; Oliphant, Anthony; Olvera, Daniel

    2004-01-01

    Includes supplementary material. Recent conflicts such as Operation Desert Shield/Storm and Operation Iraqi Freedom highlight the logistics difficulties the United States faces by relying on foreign access and infrastructure and large supply stockpiles ashore to support expeditionary operations. The Navy's transformational vision for the future, Sea Power 21, involves Seabasing as a way to address these difficulties by projecting and sustaining joint forces globally from the sea. This stud...

  2. Joint reflection in teacher training

    Czech Academy of Sciences Publication Activity Database

    Tichá, Marie; Hošpesová, A.; Macháčková, Jana

    Plzeň : ZČU PedF, 2006 - (Coufalová, J.), s. 293-298 ISBN 80-7043-478-3. [CIEAEM 58. Srní (CZ), 09.07.2006-15.07.2006] R&D Projects: GA ČR(CZ) GA406/05/2444 Institutional research plan: CEZ:AV0Z10190503 Keywords : individual reflection * joint reflection * teachers´knowledge base Subject RIV: AM - Education

  3. Hydrocolonotherapy ankle joints after injuries

    OpenAIRE

    Volodymyr Muchin; Oleksandr Zviriaka

    2016-01-01

    Muchin V., Zviriaka O. Purpose: to improve efficiency of gydrokinesitherapy by means of specially designed devices and monolasts for patients after ankle joint injuries. Material & Methods: there are pedagogical methods, clinical and radiological methods, anthropometric measurements and goniometry were used. Results: the author's technique of hydrokinesitherapy with application hydrokinesimechanotherapy device in the program of physical rehabilitation which provides optimum conditions for...

  4. Adenosine in inflammatory joint diseases

    OpenAIRE

    Chan, E. S. L.; Fernandez, P.; Cronstein, B. N.

    2007-01-01

    Inflammatory joint diseases are a group of heterogeneous disorders with a variety of different etiologies and disease manifestations. However, there are features that are common to all of them: first, the recruitment of various inflammatory cell types that are attracted to involved tissues over the course of the disease process. Second, the treatments used in many of these diseases are commonly medications that suppress or alter immune function. The demonstration that adenosine has endogenous...

  5. Compound composite odontoma

    Directory of Open Access Journals (Sweden)

    G Girish

    2016-01-01

    Full Text Available The term odontoma has been used as a descriptor for any tumor of odontogenic origin. It is a growth in which both epithelial and mesenchymal cells exhibits complete differentiation. Odontomas are considered as hamartomas rather than true neoplasm. They are usually discovered on routine radiographic examination. Odontomas, according to the World Health Organization, are classified into complex odontoma and compound odontomas. The present paper reports a case of compound composite odontomas.

  6. Compound composite odontoma.

    Science.gov (United States)

    Girish, G; Bavle, Radhika M; Singh, Manish Kumar; Prasad, Sahana N

    2016-01-01

    The term odontoma has been used as a descriptor for any tumor of odontogenic origin. It is a growth in which both epithelial and mesenchymal cells exhibits complete differentiation. Odontomas are considered as hamartomas rather than true neoplasm. They are usually discovered on routine radiographic examination. Odontomas, according to the World Health Organization, are classified into complex odontoma and compound odontomas. The present paper reports a case of compound composite odontomas. PMID:27194882

  7. Compounding a Problem?

    Science.gov (United States)

    Berlin, Joey

    2016-01-01

    Allergist-immunologists say a U.S. Pharmacopeia proposal will mess with an allergy treatment system that's worked for more than a century. The revised standards, if adopted, would remove a key exemption separating allergen extract preparations from the stricter requirements of other compounds. Immunologists say the exemption has allowed them to compound allergen extracts in their own offices, and they've done so safely and effectively millions of times a year. PMID:27175928

  8. Phenolic compounds in flaxseed

    OpenAIRE

    Johnsson, Pernilla

    2004-01-01

    The dietary lignan secoisolariciresinol diglucoside (SDG), present in high concentrations in flaxseed, and its metabolites enterolactone and enterodiol are thought to decrease the risk of hormone dependent cancers, cardiovascular disease and other “welfare” diseases. Flaxseed also contains other biologically active phenolic compounds, such as phenolic acids. The understanding of the nature of these compounds is crucial for their possible exploitation in drugs and functional foods. Until the m...

  9. Joints for large superconducting conductors

    International Nuclear Information System (INIS)

    Large fusion magnets call for high-current conductors (up to 60 kA). This has been achieved by the cable-in-conduit conductor concept. The connection of these conductors has to take into account several demanding boundary conditions: a large number of strands (around 1000), a low resistance at high current (1-2 nΩ), low losses in pulsed field operation, Nb3Sn heat treatment, helium tightness control, limited available space. A conceptual design was developed by the CEA, based on the connection of two separate twin boxes clamped together, according to the lap-joint concept. These boxes are machined out of an explosive bonding plate (jacket material/copper), and the electrical connection is achieved by tin-lead soldering of the facing copper soles. After qualification of the explosive bond and validation of the joint concept in the laboratory, the technology was transferred to the industry within the framework of the manufacture of the ITER Toroidal Field Model Coil (TFMC). In addition, three full-size joint samples (FSJS), relevant to different jacket materials and joining techniques, were manufactured by the industry and successfully tested in the SULTAN facility at CRPP, Villigen. The paper reports on the results of the laboratory tests, describes the transfer of technology to industry, and lastly presents some typical experimental results

  10. Mechanical flexible joint design document

    Science.gov (United States)

    Daily, Vic

    1993-01-01

    The purpose of this report is to document the status of the Mechanical Flexible Joint (MFJ) Design Subtask with the intent of halting work on the design. Recommendations for future work is included in the case that the task is to be resumed. The MFJ is designed to eliminate two failure points from the current flex joint configuration, the inner 'tripod configuration' and the outer containment jacket. The MFJ will also be designed to flex 13.5 degrees and have three degrees of freedom. By having three degrees of freedom, the MFJ will allow the Low Pressure Fuel Duct to twist and remove the necessity to angulate the full 11 degrees currently required. The current flex joints are very labor intensive and very costly and a simple alternative is being sought. The MFJ is designed with a greater angular displacement, with three degrees of freedom, to reside in the same overall envelope, to meet weight constraints of the current bellows, to be compatible with cryogenic fuel and oxidizers, and also to be man-rated.

  11. Space Suit Joint Torque Testing

    Science.gov (United States)

    Valish, Dana J.

    2011-01-01

    In 2009 and early 2010, a test was performed to quantify the torque required to manipulate joints in several existing operational and prototype space suits in an effort to develop joint torque requirements appropriate for a new Constellation Program space suit system. The same test method was levied on the Constellation space suit contractors to verify that their suit design meets the requirements. However, because the original test was set up and conducted by a single test operator there was some question as to whether this method was repeatable enough to be considered a standard verification method for Constellation or other future space suits. In order to validate the method itself, a representative subset of the previous test was repeated, using the same information that would be available to space suit contractors, but set up and conducted by someone not familiar with the previous test. The resultant data was compared using graphical and statistical analysis and a variance in torque values for some of the tested joints was apparent. Potential variables that could have affected the data were identified and re-testing was conducted in an attempt to eliminate these variables. The results of the retest will be used to determine if further testing and modification is necessary before the method can be validated.

  12. Phenolic Molding Compounds

    Science.gov (United States)

    Koizumi, Koji; Charles, Ted; de Keyser, Hendrik

    Phenolic Molding Compounds continue to exhibit well balanced properties such as heat resistance, chemical resistance, dimensional stability, and creep resistance. They are widely applied in electrical, appliance, small engine, commutator, and automotive applications. As the focus of the automotive industry is weight reduction for greater fuel efficiency, phenolic molding compounds become appealing alternatives to metals. Current market volumes and trends, formulation components and its impact on properties, and a review of common manufacturing methods are presented. Molding processes as well as unique advanced techniques such as high temperature molding, live sprue, and injection/compression technique provide additional benefits in improving the performance characterisitics of phenolic molding compounds. Of special interest are descriptions of some of the latest innovations in automotive components, such as the phenolic intake manifold and valve block for dual clutch transmissions. The chapter also characterizes the most recent developments in new materials, including long glass phenolic molding compounds and carbon fiber reinforced phenolic molding compounds exhibiting a 10-20-fold increase in Charpy impact strength when compared to short fiber filled materials. The role of fatigue testing and fatigue fracture behavior presents some insight into long-term reliability and durability of glass-filled phenolic molding compounds. A section on new technology outlines the important factors to consider in modeling phenolic parts by finite element analysis and flow simulation.

  13. Magnetic resonance evidence of joint effusion in patients with temporomandibular joint disorders

    Energy Technology Data Exchange (ETDEWEB)

    Ko, Jee Young; Kim, Kee Deog; Park, Chang Seo [Yonsei Univ. College of Dentistry, Seoul (Korea, Republic of)

    2001-06-15

    The purpose of this study was to find the relationship among the joint status, pain and effusion in patients with temporomandibular joint disorders. Materials included 406 patients (812 joints) with clinical records and bilateral TMJ MRIs in TMJ clinic, Yongdong Severance Hospital. All joints were classified in 4 groups in MR images according to the disc status of joint; normal disc position, disc displacement with reduction (DDsR), and also 2 groups according to the bony status of joint; normal bony structure and osteoarthrosis. MR evidence of joint effusion was categorized in 4 groups according to its amount. To determine the relationship between joint pain and joint effusion, 289 patients with unilateral TMJ symptoms were selected from total materials. Joint effusion was found 8.0% in normal disc position, 32.6% in DDcR, and 59.2% in DDsR (83.1% in early state and 23.1% in late stage). Joint effusion was found 39.7% in osteoarthrosis and 35.0% in normal bony structure. Joint effusion was more found in the painful joints (49.8%) than in the painless joints (22.4%) (p<0.001). Joint effusion in the early stage of DDsR only was more found significantly in painful joints (91.9%) than in painless joints (62.1%) (p<0.001). MR evidence of joint effusion might be related to disc displacement regardless of the presence of osteoarthrosis, and the early stage of DDsR was found more frequently combined with joint effusion and joint pain.

  14. Magnetic resonance evidence of joint effusion in patients with temporomandibular joint disorders

    International Nuclear Information System (INIS)

    The purpose of this study was to find the relationship among the joint status, pain and effusion in patients with temporomandibular joint disorders. Materials included 406 patients (812 joints) with clinical records and bilateral TMJ MRIs in TMJ clinic, Yongdong Severance Hospital. All joints were classified in 4 groups in MR images according to the disc status of joint; normal disc position, disc displacement with reduction (DDsR), and also 2 groups according to the bony status of joint; normal bony structure and osteoarthrosis. MR evidence of joint effusion was categorized in 4 groups according to its amount. To determine the relationship between joint pain and joint effusion, 289 patients with unilateral TMJ symptoms were selected from total materials. Joint effusion was found 8.0% in normal disc position, 32.6% in DDcR, and 59.2% in DDsR (83.1% in early state and 23.1% in late stage). Joint effusion was found 39.7% in osteoarthrosis and 35.0% in normal bony structure. Joint effusion was more found in the painful joints (49.8%) than in the painless joints (22.4%) (p<0.001). Joint effusion in the early stage of DDsR only was more found significantly in painful joints (91.9%) than in painless joints (62.1%) (p<0.001). MR evidence of joint effusion might be related to disc displacement regardless of the presence of osteoarthrosis, and the early stage of DDsR was found more frequently combined with joint effusion and joint pain

  15. Joint denervation and neuroma surgery as joint-preserving therapy for ankle pain.

    Science.gov (United States)

    Gohritz, Andreas; Dellon, A Lee; Kalbermatten, Daniel; Fulco, Ilario; Tremp, Mathias; Schaefer, Dirk J

    2013-09-01

    Partial joint denervation or surgical neuroma therapy are alternative concepts to treat pain around the ankle joint that preserve joint function and relieve pain by interrupting neural pathways that transmit pain impulses from the joint to the brain. This review article summarizes the indication, anatomic background, operative techniques, and clinical results of joint denervation or neuroma surgery, which, although rarely reported and used, may provide a valuable alternative treatment in selected patients with neurogenous problems around the ankle. PMID:24008220

  16. Effect of joining parameters on microstructure of dissimilar metal joints between aluminum and galvanized steel

    International Nuclear Information System (INIS)

    Highlights: • Weld joints obtained with different welding parameters were investigated. • The phases of the intermetallic compound layer at the interface were studied. • Effect of heat input in base metal on the intermetallic phases was discussed. • Thermodynamic calculation was carried out for the Fe2Al5 and FeAl3 phases. • The formation process of the intermetallic compound layer was analyzed. - Abstract: The interfacial microstructures of aluminum and galvanized steel dissimilar joint formed by pulsed double electrode gas metal arc (Pulsed DE-GMA) welding–brazing were characterized. Electron probe microanalyzer (EPMA) analysis revealed that the intermetallic compound layer of the welding–brazing joint consisted of Fe2Al5 and FeAl3. Comprehensive analysis of the effect of the heat input parameters showed that, at a constant total welding current (Itotal), the thickness of intermetallic compound at the interface of aluminum and steel decreased with the increase of bypass current. Thermodynamic calculations were carried out to derive the Gibbs free energy diagram for Fe2Al5 and FeAl3. These calculations presented that Fe2Al5 firstly formed, subsequently FeAl3 precipitated during welding process. Further model of the Fe2Al5 and FeAl3 intermetallic compounds formation process was proposed

  17. Nickel-coated Steel Stud to Aluminum Alloy Joints Made by High Frequency Induction Brazing

    Institute of Scientific and Technical Information of China (English)

    GE Jiaqi; WANG Kehong; ZHANG Deku; WANG Jian

    2015-01-01

    Nickel-coated 45 steel studs and 6061 aluminum alloy with 4047 Al alloy foil asfi ller metal were joined by using high frequency induction brazing. The microstructure of Fe/Al brazed joint was studied by means of optical microscopy (OM), scanning electron microscope (SEM), energy dispersive X-ray (EDX), and X-ray diffraction (XRD). Results showed that 45 steel stud and 6061 aluminum alloy could be successfully joined by high frequency induction brazing with proper processing parameters. The bonding strength of the joint was of the order of 88 MPa. Ni coating on steel stud successfully avoided the generation of Fe-Al intermetallic compound which is brittle by blocking the contact between Al and Fe. Intermetallic compounds, i e,Al3Ni2, Al1.1Ni0.9 and Al0.3Fe3Si0.7 presented in Al side, FeNi and Fe-Al-Ni ternary eutectic structure were formed in Fe side. The micro-hardness in intermetallic compound layer was 313 HV. The joint was brittle fractured in the intermetallic compounds layer of Al side, where plenty of Al3Ni2 intermetallic compounds were distributed continuously.

  18. The compound ethers of glycerin

    International Nuclear Information System (INIS)

    In this chapter of book authors describe several methods of receiving of compound ethers of glycerin. The important technic significance have compound glycerin ether and nitric acid. This compound receive by reaction of glycerin with fuming nitric acid

  19. Control of interfacial intermetallic compounds in Fe–Al joining by Zn addition

    Energy Technology Data Exchange (ETDEWEB)

    Yang, J. [Key Laboratory of Robot and Welding Automation of Jiangxi Province, School of Mechanical and Electrical Engineering, Nanchang University, Nanchang, Jiangxi 330031 (China); Center for Advanced Materials Joining, University of Waterloo, Waterloo, Ontario, Canada N2L 3G1 (Canada); Li, Y.L., E-mail: liyulong1112ster@gmail.com [Key Laboratory of Robot and Welding Automation of Jiangxi Province, School of Mechanical and Electrical Engineering, Nanchang University, Nanchang, Jiangxi 330031 (China); Zhang, H. [Key Laboratory of Robot and Welding Automation of Jiangxi Province, School of Mechanical and Electrical Engineering, Nanchang University, Nanchang, Jiangxi 330031 (China); Guo, W. [Center for Advanced Materials Joining, University of Waterloo, Waterloo, Ontario, Canada N2L 3G1 (Canada); School of Mechanical Engineering and Automation, Beijing University of Aeronautics and Astronautics, Beijing 100191 (China); Zhou, Y. [Center for Advanced Materials Joining, University of Waterloo, Waterloo, Ontario, Canada N2L 3G1 (Canada)

    2015-10-01

    By Zn addition to the fusion zone, the interfacial intermetallic compounds (IMCs) of laser Al/steel joint changed from layered Fe{sub 2}Al{sub 5} and needle-like FeAl{sub 3} to layered Fe{sub 2}Al{sub 5−x}Zn{sub x} and dispersed FeZn{sub 10} with minor Al-rich amorphous phase. This resulted in an improvement in the joint strength and the change of failure mode.

  20. Control of interfacial intermetallic compounds in Fe–Al joining by Zn addition

    International Nuclear Information System (INIS)

    By Zn addition to the fusion zone, the interfacial intermetallic compounds (IMCs) of laser Al/steel joint changed from layered Fe2Al5 and needle-like FeAl3 to layered Fe2Al5−xZnx and dispersed FeZn10 with minor Al-rich amorphous phase. This resulted in an improvement in the joint strength and the change of failure mode

  1. Compound management beyond efficiency.

    Science.gov (United States)

    Burr, Ian; Winchester, Toby; Keighley, Wilma; Sewing, Andreas

    2009-06-01

    Codeveloping alongside chemistry and in vitro screening, compound management was one of the first areas in research recognizing the need for efficient processes and workflows. Material management groups have centralized, automated, miniaturized and, importantly, found out what not to do with compounds. While driving down cost and improving quality in storage and processing, researchers still face the challenge of interfacing optimally with changing business processes, in screening groups, and with external vendors and focusing on biologicals in many companies. Here we review our strategy to provide a seamless link between compound acquisition and screening operations and the impact of material management on quality of the downstream processes. Although this is driven in part by new technologies and improved quality control within material management, redefining team structures and roles also drives job satisfaction and motivation in our teams with a subsequent positive impact on cycle times and customer feedback. PMID:19502566

  2. Fluorine-18 labelled compounds

    International Nuclear Information System (INIS)

    The work presented in this thesis deals with the problems involved in the adaption of reactor-produced fluorine-18 to the synthesis of 18F-labelled organic fluorine compounds. Several 18F-labelling reagents were prepared and successfully applied. The limitations to the synthetic possibilities of reactor-produced fluoride-18 become manifest in the last part of the thesis. An application to the synthesis of labelled aliphatic fluoro amino acids has appeared to be unsuccessful as yet, although some other synthetic approaches can be indicated. Seven journal articles (for which see the availability note) are used to compose the four chapters and three appendices. The connecting text gives a survey of known 18F-compounds and methods for preparing such compounds. (Auth.)

  3. Part I. Remembering No. 2 (Ladislav Loerinc). EMO joint venture, joint-stock company - really completely useless organ?

    International Nuclear Information System (INIS)

    In this chapter author reviewed the story of the EMO joint venture, joint-stock company, between Slovenske elektrarne, a. s. and EdF. EMO joint venture, joint-stock company, was established to complete the Mochovce nuclear power plant. EMO joint venture, joint-stock company was closed after one year of work. History of EMO joint venture, joint-stock company, was described by its former general manager Mr. Ladislav Loerinc.

  4. Joint toxicity of alkoxyethanol mixtures: contribution of in silico applications.

    Science.gov (United States)

    Pohl, H R; Ruiz, P; Scinicariello, F; Mumtaz, M M

    2012-10-01

    Exposure to chemicals occurs often as mixtures. Presented in this paper is information on alkoxyethanols and the impact they might have on human health in combination with some commonly found aliphatic and aromatic compounds. Our studies to evaluate the joint toxicity of these chemicals among themselves and in combination with other chemicals reveal a variety of possible outcomes depending on the exposure scenario. The interactions are predominantly based on metabolic pathways and are common among several solvents and organic compounds. Quantitative structure activity relationship (QSAR) analysis can be used with high confidence to identify chemicals that will interact to influence overall joint toxicity. Potential human exposure to a combination of alkoxyethanol, toluene and substituted benzenes may increase reproductive and developmental disease conditions. Inheritable gene alterations result in changes in the enzyme function in different subpopulations causing variations in quantity and/or quality of particular isoenzymes. These changes are responsible for differential metabolism of chemicals in species, genders, and life stages and are often the basis of a population's susceptibility. Unique genotypes introduced as a function of migration can alter the genetic makeup of any given population. Hence special consideration should be given to susceptible populations while conducting chemical health risk assessments. PMID:22749914

  5. Adaptive strategy for joint measurements

    Science.gov (United States)

    Uola, Roope; Luoma, Kimmo; Moroder, Tobias; Heinosaari, Teiko

    2016-08-01

    We develop a technique to find simultaneous measurements for noisy quantum observables in finite-dimensional Hilbert spaces. We use the method to derive lower bounds for the noise needed to make incompatible measurements jointly measurable. Using our strategy together with recent developments in the field of one-sided quantum information processing we show that the attained lower bounds are tight for various symmetric sets of quantum measurements. We use this characterisation to prove the existence of so called 4-Specker sets, i.e. sets of four incompatible observables with compatible subsets in the qubit case.

  6. Automatic locking knee brace joint

    Science.gov (United States)

    Weddendorf, Bruce (Inventor)

    1995-01-01

    This invention is an apparatus for controlling the pivotal movement of a knee brace comprising a tang-and-clevis joint that has been uniquely modified. Both the tang and the clevis have a set of teeth that, when engaged, can lock the tang and the clevis together. In addition, the tang is biased away from the clevis. Consequently, when there is no axial force (i.e., body weight) on the tang, the tang is free to pivot within the clevis. However, when an axial force is exerted on the tang, the tang is pushed into the clevis, both sets of teeth engage, and the tang and the clevis lock together.

  7. Jet Joint Undertaking. Vol. 2

    International Nuclear Information System (INIS)

    The scientific, technical, experimental and theoretical investigations related to JET tokamak are presented. The JET Joint Undertaking, Volume 2, includes papers presented at: the 15th European Conference on controlled fusion and plasma heating, the 15th Symposium on fusion technology, the 12th IAEA Conference on plasma physics and controlled nuclear fusion research, the 8th Topical Meeting on technology of fusion. Moreover, the following topics, concerning JET, are discussed: experience with wall materials, plasma performance, high power ion cyclotron resonance heating, plasma boundary, results and prospects for fusion, preparation for D-T operation, active gas handling system and remote handling equipment

  8. Joint studies on large CANDU

    International Nuclear Information System (INIS)

    CANDU PHWRs have demonstrated generic benefits which will be continued in future designs. These include economic benefits due to low operating costs, business potential, strategic benefits due to fuel cycle flexibility and operational benefits. These benefits have been realized in Korea through the operation of Wolsong 1, resulting in further construction of PHWRs at the same site. The principal benefit, low electricity cost, is due to the high capacity factor and the low fuel cost for CANDU. The CANDU plant at Wolsong has proven to be a safe, reliable and economical electricity producer. The ability of PHWR to burn natural uranium ensures security of fuel supply. Following successful Technology Transfer via the Wolsong 2,3 and 4 project, future opportunity exists between Korea and Canada for continuing co-operation in research and development to improve the technology base, for product development partnerships, and business opportunities in marketing and building PHWR plants in third countries. High reliability, through excellent design, well-controlled operation, efficient maintenance and low operating costs is critical to the economic viability of nuclear plants. CANDU plants have an excellent performance record. The four operating CANDU 6 plants, operated by four utilities in three countries, are world performance leaders. The CANDU 9 design, with higher output capacity, will help to achieve better site utilization and lower electricity costs. Being an evolutionary design, CANDU 9 assures high performance by utilizing proven systems, and component designs adapted from operating CANDU plants (Bruce B, Darlington and CANDU 6). All system and operating parameters are within the operating proven range of current plants. KAERI and AECL have an agreement to perform joint studies on future PHWR development. The objective of the joint studies is to establish the requirements for the design of future advanced CANDU PHWR including the utility need for design improvements

  9. The joint implementation mechanisms (MOC)

    International Nuclear Information System (INIS)

    The aim of the joint implementation mechanisms (MOC) is aims to favor the fight against the climatic change, by the implementing of activities, technologies and appropriate techniques emitting less greenhouse gases in south countries and by the possibility of reducing the greenhouse gases emissions for a more economical cost. This guide brings a practical assistance to the projects set-up: the possible concerned projects, the formalization of the project, the methodology, the involvement of the carbon credits in the project financing. (A.L.B.)

  10. Compound semiconductor device physics

    CERN Document Server

    Tiwari, Sandip

    2013-01-01

    This book provides one of the most rigorous treatments of compound semiconductor device physics yet published. A complete understanding of modern devices requires a working knowledge of low-dimensional physics, the use of statistical methods, and the use of one-, two-, and three-dimensional analytical and numerical analysis techniques. With its systematic and detailed**discussion of these topics, this book is ideal for both the researcher and the student. Although the emphasis of this text is on compound semiconductor devices, many of the principles discussed will also be useful to those inter

  11. Water flow in single rock joints

    International Nuclear Information System (INIS)

    To study the hydromechanical properties of single rock joints a technique to make transparent replicas of natural joint surfaces has been developed. Five different joint samples were replicated and studied. The aperture distribution of the joints were obtained through a measurements method provided by the transparent replicas, The principle behind the method is that a water drop with a known volume, which is placed inside a joint, will cover a certain area of the surface depending on the size of aperture at the actual point. Flow tests were performed on the same joint replicas. The tortuosity of the flow and the velocity along single stream lines were measured using colour injections in the water flow through the joints. The equivalent hydraulic apertures determined from the flow tests were shown to be smaller than the average mechanical apertures. The velocity of the flow varies strongly between different paths over the joint depending on the spatial distribution of the apertures. The degree of matedness between the joint surfaces is an important factor influencing the channeling character of the joints. (38 refs.)(author)

  12. Water flow in single rock joints

    International Nuclear Information System (INIS)

    To study the hydromechanical properties of single rock joints a technique to make transparent replicas of natural joint surfaces has been developed. Five different joint samples were replicated and studied. The aperture distribution of the joints were obtained through a measurement method provided by the transparent replicas. The principle behind the method is that a water drop with a known volume, which is placed inside a joint, will cover a certain area of the surface depending on the average size of aperture at the actual point. Flow tests were performed on the same joint replicas. The tortuousity of the flow and the velocity along single stream lines were measured using colour injections into the water flow through the joints. The equivalent hydraulic apertures determined from the flow tests where shown to be smaller than the average mechanical apertures. The velocity of the flow varies strongly between different paths over the joint depending on the spatial distribution of the apertures. The degree of matedness between the joint surfaces is an important factor influencing the channeling character of the joints. (author) (38 refs.)

  13. Localized chondrocalcinosis in traumatized joints

    International Nuclear Information System (INIS)

    The radiographs and medical records were reviewed of 76 patients who presented with chondrocalcinosis over a period of two years. Two groups of patients could be distinguished. The first group consisted of 58 mostly elderly patients (age 53-89 years [mean 71.8]). In these, chondrocalcinosis was most likely to be caused by an underlying disease such as calcium crystal deposition disease or it was present in association with osteoarthritis. In most cases of this group the findings were bilateral. The second group consisted of 18 patients who were significantly younger (age 15-69 years [mean 43.1]). In these patients there was no evidence of an underlying disease. Chondrocalcinosis was seen in only one joint, which had sustained damage by surgery or trauma. The knees were affected in the majority of cases and meniscectomy was believed to be the previous trauma in most of these cases. The hands were involved in two patients, the wrist, shoulder, or elbow were involved in other patients. In two cases with chondrocalcinosis in the hand and knee, the findings disappeared several weeks to months after the injury. The findings in the group of patients with a history of trauma or surgery and no other disease, support the concept that chondrocalcinosis may result from previous joint damage. (orig.)

  14. Flavour Compounds in Fungi

    DEFF Research Database (Denmark)

    Ravasio, Davide Antonio

    Fungi produce a variety of volatile organic compounds (VOCs) during their primary or secondary metabolism and with a wide range of functions. The main focus of this research work has been put on flavour molecules that are produced during fermentation processes, mainly esters and alcohols derived...

  15. Forecasting of superconducting compounds

    International Nuclear Information System (INIS)

    In forecasting new superconducting intermetallic compounds of the A15 and Mo3Se types most promising from the viewpoint of high critical temperature Tsub(c), high critical magnetic fields Hsub(c), and high critical currents and in estimating their transition temperature it is proposed to apply cybernetic methods of computer learning

  16. Chemical compounds in teak

    Directory of Open Access Journals (Sweden)

    Fernanda Viana da Silva Leonardo

    2015-09-01

    Full Text Available Quinone compounds are largely generated at extractive fraction of the woods in a complex and variable biological system. The literature has indications for many segments from food industry to pharmaceutical industry. Within the field of industrial use of wood, they are less desirable since they are treated only as incidental substances in production strings of pulp, paper, charcoal, and sawmill. In spite of its small amount, compared to other chemical compounds called essential, these substances have received special attention from researchers revealing a diverse range of offerings to market products textiles, pharmaceuticals, colorants, and other polymers, for which are being tested and employed. Quinones are found in fungi, lichens, and mostly in higher plants. Tectona grandis, usually called teak, is able to biosynthesize anthraquinones, which is a quinone compound, byproduct of secondary metabolism. This species provides wood that is much prized in the furniture sector and can also be exploited for metabolites to supply the market in quinone compounds and commercial development of new technologies, adding value to the plantations of this species within our country.

  17. NATURAL POLYACETYLENE COMPOUNDS

    Directory of Open Access Journals (Sweden)

    A. M. Nasukhova

    2014-01-01

    Full Text Available In article the review of the initial stage of researches of natural polyacetylene compounds is resulted. The high reactionary ability leading to fast oxidation and degradation of these compounds, especially at influence of Uf-light, oxygen of air, pH and other factors, has caused the serious difficulties connected with an establishment of structure and studying of their physical and chemical properties. Therefore the greatest quantity of works of this stage is connected with studying of essential oils of plants from families Apiaceae, Araliaceae, Asteraceae, Campanulaceae, Olacaceae, Pittosporaceae and Santalaceae where have been found out, basically, diacetylene compounds. About development of physical and chemical methods of the analysis of possibility of similar researches have considerably extended. More than 2000 polyacetylenes are known today, from them more than 1100 are found out in plants fam. Asteraceae. Revolution in the field of molecular biology has allowed to study processes of biosynthesis of these compounds intensively.

  18. Stabilization of labelled compounds

    International Nuclear Information System (INIS)

    This invention concerns a composition including a labelled compound, and the vitamin B 12. This vitamin gives a red colour to the solution and stabilize it radiochemically, allowing to transport the solution at ambient temperature and a storage at 4 degrees celsius. (N.C.). 5 refs

  19. Compound floating pivot micromechanisms

    Science.gov (United States)

    Garcia, Ernest J.

    2001-04-24

    A new class of tilting micromechanical mechanisms have been developed. These new mechanisms use compound floating pivot structures to attain far greater tilt angles than are practical using other micromechanical techniques. The new mechanisms are also capable of bi-directional tilt about multiple axes.

  20. Fissibility of compound nuclei

    CERN Document Server

    Iwata, Yoritaka

    2012-01-01

    Collisions between $^{248}$Cm and $^{48}$Ca are systematically investigated by time-dependent density functional calculations with evaporation prescription. Depending on the incident energy and impact parameter, fusion, deep-inelastic and fission events are expected to appear. In this paper, a microscopic method of calculating the fissibility of compound nuclei is presented.

  1. Flat H Frangible Joint Evolution

    Science.gov (United States)

    Diegelman, Thomas E.; Hinkel, Todd J.; Benjamin, Andrew; Rochon, Brian V.; Brown, Christopher W.

    2016-01-01

    Space vehicle staging and separation events require pyrotechnic devices. They are single-use mechanisms that cannot be tested, nor can failure-tolerant performance be demonstrated in actual flight articles prior to flight use. This necessitates the implementation of a robust design and test approach coupled with a fully redundant, failure-tolerant explosive mechanism to ensure that the system functions even in the event of a single failure. Historically, NASA has followed the single failure-tolerant (SFT) design philosophy for all human-rated spacecraft, including the Space Shuttle Program. Following the end of this program, aerospace companies proposed building the next generation human-rated vehicles with off-the-shelf, non-redundant, zero-failure-tolerant (ZFT) separation systems. Currently, spacecraft and launch vehicle providers for both the Orion and Commercial Crew Programs (CCPs) plan to deviate from the heritage safety approach and NASA's SFT human rating requirements. Both programs' partners have base-lined ZFT frangible joints for vehicle staging and fairing separation. These joints are commercially available from pyrotechnic vendors. Non-human-rated missions have flown them numerous times. The joints are relatively easy to integrate structurally within the spacecraft. In addition, the separation event is debris free, and the resultant pyro shock is lower than that of other design solutions. It is, however, a serious deficiency to lack failure tolerance. When used for critical applications on human-rated vehicles, a single failure could potentially lead to loss of crew (LOC) or loss of mission (LOM)). The Engineering and Safety & Mission Assurance directorates within the NASA Johnson Space Center took action to address this safety issue by initiating a project to develop a fully redundant, SFT frangible joint design, known as the Flat H. Critical to the ability to retrofit on launch vehicles being developed, the SFT mechanisms must fit within the same

  2. MR arthrography of the ankle joint

    International Nuclear Information System (INIS)

    Due to its superior soft tissue contrast conventional MRI is the imaging method of choice in the evaluation of ankle joint disorders. Conventional MR imaging can accurately demonstrate normal or acutely injured ligaments; however, in subacute and chronic injury joint fluid necessary for delineation of injured ligaments is absent and MR arthrography should be performed. MR arthrography uses the intraarticular injection of contrast material to distend the joint, yielding improved discrimination of intraarticular structures. This joint distension with MR arthrography is also helpful in the staging of osteochondritis dissecans, since in cases of unstable lesions tracking of contrast material into the interface can be more easily demonstrated. Finally, high contrast and joint distension by MR arthrography improves the detection of intraarticular loose bodies, which often require surgery. MR artrography, although invasive, may provide additional information in various ankle joint disorders. (orig.)

  3. Solder joint technology materials, properties, and reliability

    CERN Document Server

    Tu, King-Ning

    2007-01-01

    Solder joints are ubiquitous in electronic consumer products. The European Union has a directive to ban the use of Pb-based solders in these products on July 1st, 2006. There is an urgent need for an increase in the research and development of Pb-free solders in electronic manufacturing. For example, spontaneous Sn whisker growth and electromigration induced failure in solder joints are serious issues. These reliability issues are quite complicated due to the combined effect of electrical, mechanical, chemical, and thermal forces on solder joints. To improve solder joint reliability, the science of solder joint behavior under various driving forces must be understood. In this book, the advanced materials reliability issues related to copper-tin reaction and electromigration in solder joints are emphasized and methods to prevent these reliability problems are discussed.

  4. Using Joint Interviews to Add Analytic Value.

    Science.gov (United States)

    Polak, Louisa; Green, Judith

    2016-10-01

    Joint interviewing has been frequently used in health research, and is the subject of a growing methodological literature. We review this literature, and build on it by drawing on a case study of how people make decisions about taking statins. This highlights two ways in which a dyadic approach to joint interviewing can add analytic value compared with individual interviewing. First, the analysis of interaction within joint interviews can help to explicate tacit knowledge and to illuminate the range of often hard-to-access resources that are drawn upon in making decisions. Second, joint interviews mitigate some of the weaknesses of interviewing as a method for studying practices; we offer a cautious defense of the often-tacit assumption that the "naturalness" of joint interviews strengthens their credibility as the basis for analytic inferences. We suggest that joint interviews are a particularly appropriate method for studying complex shared practices such as making health decisions. PMID:25850721

  5. Reconfigurable robot based on modular joint concept

    Institute of Scientific and Technical Information of China (English)

    Shi Shicai; Xie Zongwu; Gao Xiaohui; Jin Minghe; Zhu Yingyuan; Ni Fenglei; Liu Hong; Kraemer Erich; Hirzinger Gerd

    2006-01-01

    A reconfigurable modular robot was developed for a free-flying robot project. This robot was composed of 6 same modular joints and one gripper. In order to save space and cost for transporting it into the space, the robot should be folded overall and locked. A big central hole in the modular joint was designed for the placement of the cables and plugs in the robot arm, which prevented them from damage of high temperature, radiation in the space environment and the motion of the robot. Multiple sensors were integrated into the fully modular joint, such as joint torque sensor, joint position sensor and temperature sensors, which made the joint more intelligent. A zero gravity experimental system was developed to verify the functions of the robot under zero gravity environment.

  6. Effect of Electromigration on the Type of Drop Failure of Sn-3.0Ag-0.5Cu Solder Joints in PBGA Packages

    Science.gov (United States)

    Huang, M. L.; Zhao, N.

    2015-10-01

    Board-level drop tests of plastic ball grid array (PBGA) packages were performed in accordance with the Joint Electron Devices Engineering Council standard to investigate the effect of electromigration (EM) on the drop reliability of Sn-3.0Ag-0.5Cu solder joints with two substrate surface finishes, organic solderability preservative (OSP) and electroless nickel electroless palladium immersion gold (ENEPIG). In the as-soldered state, drop failures occurred at the substrate sides only, with cracks propagating within the interfacial intermetallic compound (IMC) layer for OSP solder joints and along the IMC/Ni-P interface for ENEPIG solder joints. The drop lifetime of OSP solder joints was approximately twice that of ENEPIG joints. EM had an important effect on crack formation and drop lifetime of the PBGA solder joints. ENEPIG solder joints performed better in drop reliability tests after EM, that is, the drop lifetime of ENEPIG joints decreased by 43% whereas that of OSP solder joints decreased by 91%, compared with the as-soldered cases. The more serious polarity effect, i.e., excessive growth of the interfacial IMC at the anode, was responsible for the sharper decrease in drop lifetime. The different types of drop failure of PBGA solder joints before and after EM, including the position of initiation and the propagation path of cracks, are discussed on the basis of the growth behavior of interfacial IMC.

  7. X-ray and radionuclide investigations of the bones and joints in psoriasis

    International Nuclear Information System (INIS)

    Radiography of the bones and joints was performed in 133 psoriatic patients; osteoscintigraphy with 99mTc-phosphate compounds was also performed in 42 of them. On the basis of x-ray findings 3 types of osteoarticular psoriasis were singled out: psoriatic polyarthritis, psoriatic polyarthrosis and psoriatic arthropathy. The most ample information on the type, activity and spreading of a pathological process in the bones and joints in psoriasis can be obtained from the combination of the x-ray and radionuclide methods

  8. Thermal treatment of dissimilar steels' welded joints

    Science.gov (United States)

    Nikulina, A. A.; Denisova, A. S.; Gradusov, I. N.; Ryabinkina, P. A.; Rushkovets, M. V.

    2016-04-01

    In this paper combinations of chrome-nickel steel and high-carbon steel, produced by flash butt welding after heat treatment, are investigated. Light and electron microscopic studies show that the welded joints after heat treatment have a complex structure consisting of several phases as initial welded joints. A martensite structure in welded joints after thermal treatment at 300... 800 °C has been found.

  9. Valuing Joint Ventures Using Real Options

    OpenAIRE

    Ulrich Pape; Stephan Schmidt-Tank

    2005-01-01

    As the valuation of strategic measures becomes increasingly important, relatively few articles have discussed the valuation methods pertained for joint ventures. This paper shows that real options contribute to a better valuation of joint venture projects through superior reflection of the value drivers compared to traditional valuation methodology. Particularly, the strategic value of a joint venture and the value of flexibility that stems from a less than full commitment can be determined u...

  10. Joint hypermobility syndrome and related pain

    OpenAIRE

    Nilay Sahin; Aziz Atik; Serdar Sargin

    2016-01-01

    Hypermobility is defined as an abnormally increased range of motion of a joint resulting from the excessive laxity of the soft tissues. This paper is focused on this commonly forgotten cause of several morbidities. The etiology of hypermobility is not very well known. One decade ago, joint hypermobility syndrome was considered as a benign condition, but now it is recognized as a significant contributor to chronic musculoskeletal pain, besides impacting on other organs. Patients with joint hyp...

  11. Opioid ligands and receptors of the joint

    OpenAIRE

    Bergström, Jonas

    2006-01-01

    The aim was to explore the occurrence of an opioid system in joints. Thus, joint tissues from rats with and without arthritis and also from patients with knee osteoarthrosis were investigated by EM, immunohistochemistry, RIA, HPLC, receptor binding assay and RT-PCR. In rat joints, EM demonstrated the occurrence of met-enkephalin (ME) in nerve fibers, but also in osteoblasts, osteocytes, endothelial, synovial and monoblastic cells. The novel finding of multiple sources of op...

  12. Subspace Methods for Joint Sparse Recovery

    OpenAIRE

    Lee, Kiryung; Bresler, Yoram; Junge, Marius

    2010-01-01

    We propose robust and efficient algorithms for the joint sparse recovery problem in compressed sensing, which simultaneously recover the supports of jointly sparse signals from their multiple measurement vectors obtained through a common sensing matrix. In a favorable situation, the unknown matrix, which consists of the jointly sparse signals, has linearly independent nonzero rows. In this case, the MUSIC (MUltiple SIgnal Classification) algorithm, originally proposed by Schmidt for the direc...

  13. Septic Arthritis in the Temporomandibular Joint

    OpenAIRE

    2015-01-01

    Septic arthritis of the temporomandibular joint (TMJ) is a rare event that has only been reported a few dozen times worldwide. This case is remarkable for septic arthritis of the TMJ joint in an otherwise healthy male. Case Report: A 24-year-old male presented to the emergency department with periauricular swelling, erythema, fever, myalgia's and generalized joint pain. He had previously sought medical attention and was placed on ciprofloxacin. However, he developed facial swelling and a rash...

  14. COMPLICATIONS OF JOINT, TENDON, AND MUSCLE INJECTIONS

    OpenAIRE

    Cheng, Jianguo; Abdi, Salahadin

    2007-01-01

    Prevention of complications is one of the most important aspects of patient care in pain management. The objective of this study is to review documented complications in medical literature that are associated with interventional pain management, specifically those associated with joint, tendon, and muscle injections. We conducted Medline research from 1966 to November 2006 using keywords complication, injection, radiofrequency, closed claim, facet, zygophyseal joint, sacroiliac joint, shoulde...

  15. Life Estimation of Hip Joint Prosthesis

    Science.gov (United States)

    Desai, C.; Hirani, H.; Chawla, A.

    2014-11-01

    Hip joint is one of the largest weight-bearing structures in the human body. In the event of a failure of the natural hip joint, it is replaced with an artificial hip joint, known as hip joint prosthesis. The design of hip joint prosthesis must be such so as to resist fatigue failure of hip joint stem as well as bone cement, and minimize wear caused by sliding present between its head and socket. In the present paper an attempt is made to consider both fatigue and wear effects simultaneously in estimating functional-life of the hip joint prosthesis. The finite element modeling of hip joint prosthesis using HyperMesh™ (version 9) has been reported. The static analysis (load due to the dead weight of the body) and dynamic analysis (load due to walking cycle) have been described. Fatigue life is estimated by using the S-N curve of individual materials. To account for progressive wear of hip joint prosthesis, Archard's wear law, modifications in socket geometry and dynamic analysis have been used in a sequential manner. Using such sequential programming reduction in peak stress has been observed with increase in wear. Finally life is estimated on the basis of socket wear.

  16. Postoperative radiologic imaging of joint arthroplasty

    International Nuclear Information System (INIS)

    With increased life expectancy in industrialised countries, improvement of implant design and operative technique, arthroplasty has become a routine procedure. The hip and knee joints are treated by arthroplasty most frequently. Nowadays joint replacement can be performed in many other joints. Radiologic imaging is an important tool for evaluation of the operative results and for detection of early and late complications. In the following article we describe the relevance of different imaging modalities as well as their systematic application in patients with joint arthroplasty. (orig.)

  17. Joint Global Change Research Institute (JGCRI)

    Data.gov (United States)

    Federal Laboratory Consortium — The Joint Global Change Research Institute (JGCRI) is dedicated to understanding the problems of global climate change and their potential solutions. The Institute...

  18. 38 CFR 4.45 - The joints.

    Science.gov (United States)

    2010-07-01

    ... (from flail joint, resections, nonunion of fracture, relaxation of ligaments, etc.). (c) Weakened... the purpose of rating disability from arthritis, the shoulder, elbow, wrist, hip, knee, and ankle...

  19. Joint prosthesis and method of bone fixation

    OpenAIRE

    Oosterom, R; Pijl, A J; Bersee, H.E.N.; Van der Helm, F.C.; Herder, J. L.

    2006-01-01

    The invention relates to a joint prosthesis (10), for example, a knee joint or shoulder joint prosthesis comprising a first, socket-holding prosthesis part (11) for attachment to a first bone (12) and a second, ball-holding prosthesis part (13) for attachment to a second bone (14) that intermates with the first prosthesis part, wherein the first bone and the second bone are situated at either side of a joint, and wherein the ball (2) of the second prosthesis part is rotatably received in the ...

  20. Joint hypermobility: incidence and some clinical symptoms

    Directory of Open Access Journals (Sweden)

    M P Isaev

    2003-01-01

    Full Text Available Objective. To study joint mobility range among urban population aged 18 to 30 years and to assess association of joint and other connective tissue structures disorders clinical signs with hypermobility. Material and methods. 769 randomly selected individuals aged 18 to 30 (mean - 25,56 years (419 female and 350 male were examined. Hypermobility was assessed with 9-point Beighton scale. Examination included skin stretchability evaluation at elbow back surface, determination of flat feet, high palate, joint pain and deformities of knee joints, joint luxation and subluxation, hand and feet vasospastic disturbances, cardiac pain, oculist examination. Methods of variational statistics were used (x2, Student's test, Spirmen's correlation. Results. Hypermobility incidence and joint mobility in population aged 18 to 30 years in Orenburg largely comply with data received in Moscow. Joint mobility up to 5 points in women and up to 4 points in men is usual for persons of this age and in absence of additional clinical symptoms cannot be considered as pathological. Knee joint deformities, presence of high palate, cardiac pain accompanied by signs of vegetative dysfunction, hand and feet vasospastic disturbances are significantly connected with degree of joint mobility and in some cases can help in hypermobility syndrome diagnosis.

  1. An evaluation of the blind lap joint for the surface mount attachment of chip components

    Science.gov (United States)

    Vianco, P. T.; Dalporto, J. F.

    Blind lap solder joints were used to attach leadless ceramic chip resistors to polyimidequartz circuit boards. Hand soldering and vapor phase reflow techniques were evaluated. The solder was 62Sn-36Pb-2Ag (wt. percent). The integrity of the solder joints was assessed by microstructural examination and room temperature shear tests. These analyses were performed on as-fabricated circuit boards as well as an those samples exposed to thermal cycling (308 cycles; -55 to 125 C; 6 C/min ramps; 120 min hold periods;) or thermal shock (100 cycles, -55 C to 125 C; liquid-to-liquid transfer; 10 min hold periods). In all cases, microscopy revealed no cracks within the solder joints. The shear strengths of the joints were 13.4 lb (59 N), as-fabricated; 10.5 lb (47 N), 308 thermal cycles; and 14.0 lb (62 N), 100 thermal shock cycles. All values were well within acceptability limits for the particular application. Measurements of the intermetallic compound thicknesses at the copper land/solder interface indicated that the additional heating cycle of the hand soldering step decreased the layer thickness as compared to non-hand soldered joints. The successful implementation of the blind lap joint can provide increased device densities on circuit boards by reducing bonding pad extension beyond the ceramic chip foot print.

  2. The joints of the evolving foot. Part I. The ankle joint.

    OpenAIRE

    Lewis, O. J.

    1980-01-01

    Evidence is presented to suggest that the eutherian ankle joint has been derived from a meniscus-containing joint such as that found in extant arboreal marsupials. Probable morphological derivatives of this meniscus are identifiable in the Eutheria. The form and function of the joint are described in sub-human Primates and the adaptations which characterize the joint in bipedal man are noted. These morphological findings permit some speculation about the palaeocology of the earliest mammals w...

  3. Pain in the hip joint

    Directory of Open Access Journals (Sweden)

    Yuri Aleksandrovich Olyunin

    2013-01-01

    Full Text Available Pathological changes that develop in the hip joints (HJ have different origins and mechanisms of development, but their main manifestation is pain. The nature of this pain cannot be well established on frequent occasions. The English-language medical literature currently classifies such disorders as greater trochanter pain syndrome (GTPS. Its major signs are chronic pain and local palpatory tenderness in the outer part of HJ. The development of GTPS may be associated with inflammation of the synovial bursae situated in the greater tronchanter, as well as with tendinitis, myorrhexis, iliotibial band syndrome, and other local changes in the adjacent tissues or with systemic diseases. So GTPS may be characterized as regional pain syndrome that frequently mimics pain induced by different diseases, including myofascial pain syndrome, osteoarthrosis, spinal diseases, etc.

  4. Computational Intelligence : International Joint Conference

    CERN Document Server

    Dourado, António; Rosa, Agostinho; Filipe, Joaquim; Kacprzyk, Janusz

    2016-01-01

    The present book includes a set of selected extended papers from the fifth International Joint Conference on Computational Intelligence (IJCCI 2013), held in Vilamoura, Algarve, Portugal, from 20 to 22 September 2013. The conference was composed by three co-located conferences:  The International Conference on Evolutionary Computation Theory and Applications (ECTA), the International Conference on Fuzzy Computation Theory and Applications (FCTA), and the International Conference on Neural Computation Theory and Applications (NCTA). Recent progresses in scientific developments and applications in these three areas are reported in this book. IJCCI received 111 submissions, from 30 countries, in all continents. After a double blind paper review performed by the Program Committee, only 24 submissions were accepted as full papers and thus selected for oral presentation, leading to a full paper acceptance ratio of 22%. Additional papers were accepted as short papers and posters. A further selection was made after ...

  5. Computational Intelligence : International Joint Conference

    CERN Document Server

    Rosa, Agostinho; Cadenas, José; Dourado, António; Madani, Kurosh; Filipe, Joaquim

    2016-01-01

    The present book includes a set of selected extended papers from the sixth International Joint Conference on Computational Intelligence (IJCCI 2014), held in Rome, Italy, from 22 to 24 October 2014. The conference was composed by three co-located conferences:  The International Conference on Evolutionary Computation Theory and Applications (ECTA), the International Conference on Fuzzy Computation Theory and Applications (FCTA), and the International Conference on Neural Computation Theory and Applications (NCTA). Recent progresses in scientific developments and applications in these three areas are reported in this book. IJCCI received 210 submissions, from 51 countries, in all continents. After a double blind paper review performed by the Program Committee, 15% were accepted as full papers and thus selected for oral presentation. Additional papers were accepted as short papers and posters. A further selection was made after the Conference, based also on the assessment of presentation quality and audience in...

  6. Pain in the hip joint

    Directory of Open Access Journals (Sweden)

    Yuri Aleksandrovich Olyunin

    2013-06-01

    Full Text Available Pathological changes that develop in the hip joints (HJ have different origins and mechanisms of development, but their main manifestation is pain. The nature of this pain cannot be well established on frequent occasions. The English-language medical literature currently classifies such disorders as greater trochanter pain syndrome (GTPS. Its major signs are chronic pain and local palpatory tenderness in the outer part of HJ. The development of GTPS may be associated with inflammation of the synovial bursae situated in the greater tronchanter, as well as with tendinitis, myorrhexis, iliotibial band syndrome, and other local changes in the adjacent tissues or with systemic diseases. So GTPS may be characterized as regional pain syndrome that frequently mimics pain induced by different diseases, including myofascial pain syndrome, osteoarthrosis, spinal diseases, etc.

  7. Temporomandibular joint dysfunction in children

    Directory of Open Access Journals (Sweden)

    Fernanda Mara de Paiva BERTOLI

    2009-03-01

    Full Text Available Introduction and objective: The aim of this study was to review aspects related to the temporomandibular dysfunctions (TMD in children,like etiology, diagnosis and treatment, emphasizing the importance of the correct diagnosis, since these patients are in their growth and development of the face period. Literature review: The TMDs include many clinical problems that involve the mastigatory muscles, the temporomandibular joint and near structures. In children the symptoms of this syndrome are present although with mild intensitywhen compared to adults. In relation to the prevalence, there is a great amount of discordance between the authors. The TMDs in childrenhave multifatorial etiology, and the most cited in literature areparafunctional habits, traumas, occlusal, systemic and psychologicalfactors. Conclusion: The signs and symptoms of the TMDs in pediatricpopulations are generally mild and increase with age, being veryimportant the early diagnosis and the inclusion of this kind of exam in routine examinations.

  8. Comparative Study of ENIG and ENEPIG as Surface Finishes for a Sn-Ag-Cu Solder Joint

    Science.gov (United States)

    Yoon, Jeong-Won; Noh, Bo-In; Jung, Seung-Boo

    2011-09-01

    Interfacial reactions and joint reliability of Sn-3.0Ag-0.5Cu solder with two different surface finishes, electroless nickel-immersion gold (ENIG) and electroless nickel-electroless palladium-immersion gold (ENEPIG), were evaluated during a reflow process. We first compared the interfacial reactions of the two solder joints and also successfully revealed a connection between the interfacial reaction behavior and mechanical reliability. The Sn-Ag-Cu/ENIG joint exhibited a higher intermetallic compound (IMC) growth rate and a higher consumption rate of the Ni(P) layer than the Sn-Ag-Cu/ENEPIG joint. The presence of the Pd layer in the ENEPIG suppressed the growth of the interfacial IMC layer and the consumption of the Ni(P) layer, resulting in the superior interfacial stability of the solder joint. The shear test results show that the ENIG joint fractured along the interface, exhibiting indications of brittle failure possibly due to the brittle IMC layer. In contrast, the failure of the ENEPIG joint only went through the bulk solder, supporting the idea that the interface is mechanically reliable. The results from this study confirm that the Sn-Ag-Cu/ENEPIG solder joint is mechanically robust and, thus, the combination is a viable option for a Pb-free package system.

  9. Compound semiconductor device modelling

    CERN Document Server

    Miles, Robert

    1993-01-01

    Compound semiconductor devices form the foundation of solid-state microwave and optoelectronic technologies used in many modern communication systems. In common with their low frequency counterparts, these devices are often represented using equivalent circuit models, but it is often necessary to resort to physical models in order to gain insight into the detailed operation of compound semiconductor devices. Many of the earliest physical models were indeed developed to understand the 'unusual' phenomena which occur at high frequencies. Such was the case with the Gunn and IMPATI diodes, which led to an increased interest in using numerical simulation methods. Contemporary devices often have feature sizes so small that they no longer operate within the familiar traditional framework, and hot electron or even quantum­ mechanical models are required. The need for accurate and efficient models suitable for computer aided design has increased with the demand for a wider range of integrated devices for operation at...

  10. Erupted compound odontome

    Directory of Open Access Journals (Sweden)

    Shekar S

    2009-01-01

    Full Text Available Odontomas are considered to be hamartomas rather than a true neoplasm. They consist chiefly of enamel and dentin, with variable amount of pulp and cementum when fully developed. They are generally asymptomatic and are included under the benign calcified odontogenic tumors. They are usually discovered on routine radiographic examination. Eruption of an odontoma in the oral cavity is rare. Peripheral compound odontomas arise extraosseously and have a tendency to exfoliate. In this article we are reporting a case of a 15-year-old girl with peripheral compound odontoma, with a single rudimentary tooth-like structure in the mandibular right second molar region, which is about to be exfoliated. Its eruption in the oral cavity and location in the mandibular posterior region is associated with aplasia of the mandibular right second molar, making it an interesting case for reporting.

  11. Endocrine disrupting compounds

    DEFF Research Database (Denmark)

    Bøgh, I B; Christensen, P; Dantzer, V;

    2001-01-01

    With the growing concern that environmental chemicals might impair human and animal fertility, it is important to investigate the possible influence of these substances on sexual differentiation and genital development of mammals. Many of these substances are suspected to interfere with endocrine...... of alkylphenols, these are disseminated in the environment with sewage sludge, and domestic animals and humans are likely to be exposed via the food chain. Using the pig as an in vivo model, we studied the effect of intrauterine exposure to tertiary octylphenol (OP) on essential reproductive...... usefulness of in vivo animal or embryo models for the evaluation of possible consequences of human exposure to endocrine disrupting compounds is discussed. Furthermore, possible consequences of exposure to endocrine disrupting compounds for the embryo transfer industry are addressed....

  12. Organic compounds in meteorites

    Science.gov (United States)

    Lawless, J. G.

    1980-01-01

    Recent studies of carbonaceous chondrites provide evidence that certain organic compounds are indigenous and the result of an abiotic, chemical synthesis. The results of several investigators have established the presence of amino acids and precursors, mono- and dicarboxylic acids, N-heterocycles, and hydrocarbons as well as other compounds. For example, studies of the Murchison and Murray meteorites have revealed the presence of at least 40 amino acids with nearly equal abundances of D and L isomers. The population consists of both protein and nonprotein amino acids including a wide variety of linear, cyclic, and polyfunctional types. Results show a trend of decreasing concentration with increasing carbon number, with the most abundant being glycine (41 n Moles/g). These and other results to be reviewed provide persuasive support for the theory of chemical evolution and provide the only natural evidence for the protobiological subset of molecules from which life on earth may have arisen.

  13. Compound Chondrules fused Cold

    CERN Document Server

    Hubbard, Alexander

    2015-01-01

    About 4-5% of chondrules are compound: two separate chondrules stuck together. This is commonly believed to be the result of the two component chondrules having collided shortly after forming, while still molten. This allows high velocity impacts to result in sticking. However, at T ~ 1100K, the temperature below which chondrules collide as solids (and hence usually bounce), coalescence times for droplets of appropriate composition are measured in tens of seconds. Even at 1025K, at which temperature theory predicts that the chondrules must have collided extremely slowly to have stuck together, the coalescence time scale is still less than an hour. These coalescence time scales are too short for the collision of molten chondrules to explain the observed frequency of compound chondrules. We suggest instead a scenario where chondrules stuck together in slow collisions while fully solid; and the resulting chondrule pair was subsequently briefly heated to a temperature in the range of 900-1025K. In that temperatur...

  14. Hydrogen in compound semiconductors

    Energy Technology Data Exchange (ETDEWEB)

    Haller, E.E.

    1993-05-01

    Progress in the understanding of hydrogen and its interactions in III/V and II/VI compound semiconductors is reviewed. Donor, acceptor and deep level passivation is well established in III/V compounds based on electrical measurements and on spectroscopic studies. The hydrogen donor levels in GaAs and GaP are estimated to lie near E{sub v}+0.5 eV and E{sub v}+0.3 eV, respectively. Arsenic acceptors have been passivated by hydrogen in CdTe and the very first nitrogen-hydrogen local vibrational model spectra in ZnSe have been reported. This long awaited result may lead to an explanation for the poor activation of nitrogen acceptors in ZnSe grown by techniques which involve high concentrations of hydrogen.

  15. Labelled compounds. (Pt. B)

    International Nuclear Information System (INIS)

    Since the end of World War II there has been a tremendous increase in the number of compounds that have been synthesized with radioactive or stable isotopes. They have found application in many diverse fields, so much so, that hardly a single area in pure and applied science has not benefited. Not surprisingly it has been reflected in appearance of related publications. The early proceedings of the Symposia on Advances in Trace Methodology were soon followed by various Euratom sponsored meetings in which methods of preparing and storing labelled compounds featured prominently. In due course a resurgence of interest in stable isotopes, brought about by their greater availability (also lower cost) and partly by development of new techniques such as gas chromatography - mass spectrometry (gc-ms), led to the publication of proceedings of several successful conferences. More recently conferences dealing with the synthesis and applications of isotopes and isotopically labelled compounds have been established on a regular basis. In addition to the proceedings of conferences and journal publications individuals left their mark by producing definitive texts, usually on specific nuclides. Only the classic two volume publication of Murray and Williams (Organic syntheses with isotopes, New York 1985), now over 30 years old and out of print, attempted to do justice to several nuclides. With the large amount of work that has been undertaken since then it seems unlikely that an updated edition could be produced. The alternative strategy was to ask scientists currently active to review specific areas and this is the approach adopted in the present series of monographs. In this way it is intended to cover the broad advances that have been made in the synthesis and applications of isotopes and isotopically labelled compounds in the physical and biomedical sciences. (author). refs.; figs.; tabs

  16. Phenolic compounds in oats

    OpenAIRE

    Skoglund, Maria

    2008-01-01

    This research project examined how to treat raw oat material for oat-based food products in order to sustain or increase the levels of phenolic compounds. The focus was mainly on the avenanthramides, which are potentially health beneficial bioactive components found exclusively in oats. A proposed enzymatic decrease in avenanthramide levels when non heat-treated milled oats are steeped in water was investigated. The decrease was strongly suggested to be caused by a polyphenol oxidase. Althoug...

  17. Joint Attention in Autism: Teaching Smiling Coordinated with Gaze to Respond to Joint Attention Bids

    Science.gov (United States)

    Krstovska-Guerrero, Ivana; Jones, Emily A.

    2013-01-01

    Children with autism demonstrate early deficits in joint attention and expressions of affect. Interventions to teach joint attention have addressed gaze behavior, gestures, and vocalizations, but have not specifically taught an expression of positive affect such as smiling that tends to occur during joint attention interactions. Intervention was…

  18. Complications Related to Metal-on-Metal Articulation in Trapeziometacarpal Joint Total Joint Arthroplasty

    DEFF Research Database (Denmark)

    Frølich, Christina; Hansen, Torben Bæk

    2015-01-01

    Adverse reactions to metal-on-metal (MoM) prostheses are well known from total hip joint resurfacing arthroplasty with elevated serum chrome or cobalt, pain and pseudo tumor formation. It may, however, also be seen after total joint replacement of the trapeziometacarpal joint using MoM articulation...

  19. Compound chondrules fused cold

    Science.gov (United States)

    Hubbard, Alexander

    2015-07-01

    About 4-5% of chondrules are compound: two separate chondrules stuck together. This is commonly believed to be the result of the two component chondrules having collided shortly after forming, while still molten. This allows high velocity impacts to result in sticking. However, at T ∼ 1100 K, the temperature below which chondrules collide as solids (and hence usually bounce), coalescence times for droplets of appropriate composition are measured in tens of seconds. Even at 1025 K, at which temperature theory predicts that the chondrules must have collided extremely slowly to have stuck together, the coalescence time scale is still less than an hour. These coalescence time scales are too short for the collision of molten chondrules to explain the observed frequency of compound chondrules. We suggest instead a scenario where chondrules stuck together in slow collisions while fully solid; and the resulting chondrule pair was subsequently briefly heated to a temperature in the range of 900-1025 K. In that temperature window the coalescence time is finite but long, covering a span of hours to a decade. This is particularly interesting because those temperatures are precisely the critical window for thermally ionized MRI activity, so compound chondrules provide a possible probe into that vital regime.

  20. Compound Wiretap Channels

    Directory of Open Access Journals (Sweden)

    Shlomo Shamai (Shitz

    2009-01-01

    Full Text Available This paper considers the compound wiretap channel, which generalizes Wyner's wiretap model to allow the channels to the (legitimate receiver and to the eavesdropper to take a number of possible states. No matter which states occur, the transmitter guarantees that the receiver decodes its message and that the eavesdropper is kept in full ignorance about the message. The compound wiretap channel can also be viewed as a multicast channel with multiple eavesdroppers, in which the transmitter sends information to all receivers and keeps the information secret from all eavesdroppers. For the discrete memoryless channel, lower and upper bounds on the secrecy capacity are derived. The secrecy capacity is established for the degraded channel and the semideterministic channel with one receiver. The parallel Gaussian channel is further studied. The secrecy capacity and the secrecy degree of freedom (s.d.o.f. are derived for the degraded case with one receiver. Schemes to achieve the s.d.o.f. for the case with two receivers and two eavesdroppers are constructed to demonstrate the necessity of a prefix channel in encoder design. Finally, the multi-antenna (i.e., MIMO compound wiretap channel is studied. The secrecy capacity is established for the degraded case and an achievable s.d.o.f. is given for the general case.

  1. Compound Wiretap Channels

    Directory of Open Access Journals (Sweden)

    Kramer Gerhard

    2009-01-01

    Full Text Available Abstract This paper considers the compound wiretap channel, which generalizes Wyner's wiretap model to allow the channels to the (legitimate receiver and to the eavesdropper to take a number of possible states. No matter which states occur, the transmitter guarantees that the receiver decodes its message and that the eavesdropper is kept in full ignorance about the message. The compound wiretap channel can also be viewed as a multicast channel with multiple eavesdroppers, in which the transmitter sends information to all receivers and keeps the information secret from all eavesdroppers. For the discrete memoryless channel, lower and upper bounds on the secrecy capacity are derived. The secrecy capacity is established for the degraded channel and the semideterministic channel with one receiver. The parallel Gaussian channel is further studied. The secrecy capacity and the secrecy degree of freedom ( are derived for the degraded case with one receiver. Schemes to achieve the for the case with two receivers and two eavesdroppers are constructed to demonstrate the necessity of a prefix channel in encoder design. Finally, the multi-antenna (i.e., MIMO compound wiretap channel is studied. The secrecy capacity is established for the degraded case and an achievable is given for the general case.

  2. Toxic compounds in honey.

    Science.gov (United States)

    Islam, Md Nazmul; Khalil, Md Ibrahim; Islam, Md Asiful; Gan, Siew Hua

    2014-07-01

    There is a wealth of information about the nutritional and medicinal properties of honey. However, honey may contain compounds that may lead to toxicity. A compound not naturally present in honey, named 5-hydroxymethylfurfural (HMF), may be formed during the heating or preservation processes of honey. HMF has gained much interest, as it is commonly detected in honey samples, especially samples that have been stored for a long time. HMF is a compound that may be mutagenic, carcinogenic and cytotoxic. It has also been reported that honey can be contaminated with heavy metals such as lead, arsenic, mercury and cadmium. Honey produced from the nectar of Rhododendron ponticum contains alkaloids that can be poisonous to humans, while honey collected from Andromeda flowers contains grayanotoxins, which can cause paralysis of limbs in humans and eventually leads to death. In addition, Melicope ternata and Coriaria arborea from New Zealand produce toxic honey that can be fatal. There are reports that honey is not safe to be consumed when it is collected from Datura plants (from Mexico and Hungary), belladonna flowers and Hyoscamus niger plants (from Hungary), Serjania lethalis (from Brazil), Gelsemium sempervirens (from the American Southwest), Kalmia latifolia, Tripetalia paniculata and Ledum palustre. Although the symptoms of poisoning due to honey consumption may differ depending on the source of toxins, most common symptoms generally include dizziness, nausea, vomiting, convulsions, headache, palpitations or even death. It has been suggested that honey should not be considered a completely safe food. PMID:24214851

  3. Compound Passport Service: supporting corporate collection owners in open innovation.

    Science.gov (United States)

    Andrews, David M; Degorce, Sébastien L; Drake, David J; Gustafsson, Magnus; Higgins, Kevin M; Winter, Jon J

    2015-10-01

    A growing number of early discovery collaborative agreements are being put in place between large pharma companies and partners in which the rights for assets can reside with a partner, exclusively or jointly. Our corporate screening collection, like many others, was built on the premise that compounds generated in-house and not the subject of paper or patent disclosure were proprietary to the company. Collaborative screening arrangements and medicinal chemistry now make the origin, ownership rights and usage of compounds difficult to determine and manage. The Compound Passport Service is a dynamic database, managed and accessed through a set of reusable services that borrows from social media concepts to allow sample owners to take control of their samples in a much more active way. PMID:26136162

  4. Morphology of uranium compounds

    International Nuclear Information System (INIS)

    Uranium metal is being used as nuclear fuel for Indian Research Reactors. During production of U metal various intermediate compounds of uranium are being processed. Physical, chemical properties of these compounds are important in overall processing rate and conversion determination. As no systematic data on morphology of these compounds were available, study was conducted to record the morphology of various U-compounds which are important in production of ceramic and metallic U-fuel for reactors. Most important intermediates were found to be ammonium diuranate (ADU) and uranium oxide (UO3/UO2). Morphology of these powders controls their flowability required for further material movement through different equipment, surface area required for chemical reactivity of powder, carryover losses occurred during gas solid counter current reaction and tap density required for effective capacity determination. ADU particle basically consists of primary platelets of 250-500 nm width and of 500-1000 nm length. These primary platelets form primary agglomerates. These agglomerates look like woollen balls or balls or cauliflower and primary agglomerates are also connected with each other to form secondary agglomerates. The basic morphology of ADU is maintained in UO3 even after calcination at high temperature. Pores are generated at the surface of platelet of UO3 due to release of gaseous reaction products during calcination. As temperature increases more pores are generated and sintering also starts. Specific surface area of UO3, produced by the calcination of ammonium di-urinate is generally a function of two competing processes: generation of surface area due to generation of pores because of the evolution of gaseous products (NH3, H2O vapour) and the loss of surfaces due to sintering. As a results surface area increases with calcination temperature due to generation of pores and then reduces. It has also been observed that morphology of the compounds are very much processing

  5. Nomenclature and classification of temporomandibular joint disorders

    NARCIS (Netherlands)

    Stegenga, B.

    2010-01-01

    P>Currently, there are basically two approaches to classification, one based on structural and one on positional changes occurring within the joint. Despite the increase in knowledge of pathologic changes occurring within the temporomandibular joint (TMJ), the disc still seems to be a central issue

  6. Temporomandibular Joint Disorders and Orofacial Pain.

    Science.gov (United States)

    Ahmad, Mansur; Schiffman, Eric L

    2016-01-01

    Temporomandibular disorders (TMD) affect 5% to 12% of the United States population. This article discusses common conditions related to temporomandibular joints, including disc displacements, inflammatory disturbances, loose joint bodies, traumatic disturbances, and developmental conditions. Also addressed are the appropriate imaging modalities and diagnostic criteria for TMD. PMID:26614951

  7. Detection of Arthritis by Joint Scanning

    International Nuclear Information System (INIS)

    Detection and identification of early arthritis is frequently difficult with routine methods. Several tracers, 131I human serum albumin (25 μCi/10 lb), 99mTc human serum albumin (1-3 mCi), 131I iodipamide (40 μCi/10 lb), and 99mTc pertechnetate (10 mCi), have been employed for joint scanning to detect synovitis produced by arthritis in joints of the extremities. When administered intravenously, the 25% increase in localization of these tracers in the synovial membrane, if there is active synovitis, can be demonstrated by scintillation scanning. This ability to detect synovitis at an early stage enables the joint scan to show areas of active synovitis not demonstrated on roentgenograms. The scan may objectively confirm or disprove questionable physical findings. From this standpoint the technique has been useful in determining whether joint pain is functional or due to arthritis as a negative localization tends to rule out active synovitis as the cause of the pain. The scan demonstration of a positive localization of the tracer in several joints when only one area is symptomatic is evidence that joint pain is due to systemic disease. The short half-life tracera permit serial studies to follow the course of an arthritis process. Use of 99mTc pertechnetate and an Anger camera have made joint scanning a practical technique for clinical use. A review of the accuracy of joint scanning in 130 cases as compared to roentgenograms is presented. (author)

  8. High quality joints of copper bus bars

    Directory of Open Access Journals (Sweden)

    Samarjit Bhattacharyya,

    2010-08-01

    Full Text Available Efficient joints in copper bus bar conductors can be made very simply by bolting and clamping. This paper proposes the method to maximize the jointing efficiency in order to eliminate hot spots in switchgears by optimizing the effect of spreading resistance and interface resistance.

  9. Analysis of Joint Ventures Financial State

    Directory of Open Access Journals (Sweden)

    Alla V. Dmitrenko

    2013-01-01

    Full Text Available The article describes the basic techniques for the analysis of businesses financial state and methods that were adapted for the joint ventures activities, analyses joint venture financial state, makes conclusions and submits reasonable proposals for improvement of its future activities

  10. Simulation of failure process of jointed rock

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    A modified discontinuous deformation analysis (DDA) algorithm was proposed to simulate the failure behavior of jointed rock.In the proposed algorithm,by using the Monte-Carlo technique,random joint network was generated in the domain of interest.Based on the joint network,the triangular DDA block system was automatically generated by adopting the advanced front method.In the process of generating blocks,numerous artificial joints came into being,and once the stress states at some artificial joints satisfy the failure criterion given beforehand,artificial joints will turn into real joints.In this way,the whole fragmentation process of rock mass can be replicated.The algorithm logic was described in detail,and several numerical examples were carried out to obtain some insight into the failure behavior of rock mass containing random joints.From the numerical results,it can be found that the crack initiates from the crack tip,the growth direction of the crack depends upon the loading and constraint conditions,and the proposed method can reproduce some complicated phenomena in the whole process of rock failure.

  11. 29 CFR 791.2 - Joint employment.

    Science.gov (United States)

    2010-07-01

    ... INTERPRETATION NOT DIRECTLY RELATED TO REGULATIONS JOINT EMPLOYMENT RELATIONSHIP UNDER FAIR LABOR STANDARDS ACT... employment relationship with a different employer. A determination of whether the employment by the employers... the employee by the other joint employer or employers. 4 Walling v. Friend, et al., 156 F. 2d 429...

  12. CT diagnosis in the elbow joint

    International Nuclear Information System (INIS)

    The normal anatomy of the elbow joint is described. Diverse pathologic joint alterations, e.g. fractures and dislocations, ostheochondritis, inflammatory changes, and ulnar nerve lesion are demonstrated. Particular attention is paid to threedimensional (3D-) reconstruction of demonstrable pathologic findings. (orig.)

  13. Creep behavior evaluation of welded joint

    International Nuclear Information System (INIS)

    In the creep design of high temperature structural elements, it is necessary to grasp the creep performance of joints as a whole, paying attention to the essential lack of uniformity between the material qualities of parent metals and welds. In this study, the factors controlling the creep performance of butt welded joints were investigated theoretically, when they were subjected to lateral tension and longitudinal tension. It was clarified that the rupture time in the case of laterally pulled joints was determined by the ratio of the creep rupture times of weld metals and parent metals, and the rupture time in the case of longitudinally pulled joints was determined by the ratio of the creep rupture times and the ratio of the creep strain rates of weld metals and parent metals. Moreover, when the joints of the former ratio less than 1 and the latter ratio larger than 1 were investigated experimentally, the rupture time in the case of laterally pulled joints was affected by the relative thickness, and when the relative thickness was large, the theoretical and the experimental values coincided, but the relative thickness was small, the theoretical values gave the evaluation on safe side as compared with the experimental values due to the effect of restricting deformation. In the case of longitudinally pulled joints, the theoretical and the experimental values coincided relatively well. The diagram of classifying the creep performance of welded joints was proposed. (Kako, I.)

  14. Behaviour of high strength steel moment joints

    NARCIS (Netherlands)

    Girão Coelho, A.M.; Bijlaard, F.S.K.

    2010-01-01

    The design of joints to European standard EN 1993 within the semi-continuous/partially restrained philosophy is restricted to steel grades up to S460. With the recent development of high performance steels, the need for these restrictions should be revisited. The semicontinuous joint modelling can b

  15. Biomimetic Composite Structural T-joints

    Institute of Scientific and Technical Information of China (English)

    Vimal Kumar Thummalapalli; Steven L.Donaldson

    2012-01-01

    Biological structural fixed joints exhibit unique attributes,including highly optimized fiber paths which minimize stress concentrations.In addition,since the joints consist of continuous,uncut fiber architectures,the joints enable the organism to transport information and chemicals from one part of the body to the other.To the contrary,sections of man-made composite material structures are often joined using bolted or bonded joints,which involve low strength and high stress concentrations.These methods are also expensive to achieve.Additional functions such as fluid transport,electrical signal delivery,and thermal conductivity across the joints typically require parasitic tubes,wires,and attachment clips.By using the biomimetic methods,we seek to overcome the limitations which are present in the conventional methods. In the present work,biomimetic co-cured composite sandwich T-joints were constructed using unidirectional glass fiber,epoxy resin,and structural foam.The joints were fabricated using the wet lay-up vacuum bag resin infusion method.Foam sandwich T-joints with multiple continuous fiber architectures and sandwich foam thickness were prepared.The designs were tested in quasi-static bending using a mechanical load frame.The significantweight savings using the biomimetic approaches is discussed,as well as a comparison of failure modes versus architecture is described.

  16. ECOWindS Joint Action Plan

    DEFF Research Database (Denmark)

    2014-01-01

    The Joint Action Plan (JAP) is a deliverable of the ECOWindS project Work Package 4 (WP4) “Joint Action Plan”. It presents a plan of action or a roadmap for research, development, and innovation (RDI) for the Offshore Wind Service (OWS) industry. The objective of the JAP is to be an international...

  17. The cricothyroid joint in elderly Japanese individuals.

    Science.gov (United States)

    Serikawa, Masamitu; Yamamoto, Masahito; Kawamoto, Ai; Katori, Yukio; Kinoshita, Hideaki; Matsunaga, Satoru; Abe, Shin-Ichi

    2016-06-01

    Using 15 cricothyroid joint (CT joint) specimens obtained from donated cadavers of elderly individuals, we examined the morphologies of the ceratocricoid ligaments as well as the synovial tissue. The ligaments consistently contained abundant elastic fibers: the fibers tended to be straight on the anterior side in contrast to a mesh-like arrangement on the posterior side. Thick and/or long synovial folds were often evident in the CT joint. The synovial tissue usually contained CD68-positive macrophages, but the positive cells were often restricted to certain parts of the tissue. Factor VIII-positive capillaries were present but few in number, and CD3- or IgM-positive lymphocytes were absent in the synovial tissue. Degenerative changes in the joint cartilage, such as roughness or thinning, were often present, but no cartilage defects were evident. Therefore, in contrast to the small, non-weight-bearing joints of the musculoskeletal system, we considered the degeneration of the CT joint to be a specific, silent form of osteoarthritis. For high-pitched phonation and ossification of the laryngeal cartilage, the CT joint in elderly individuals seemed to maintain its anterior gliding and rotation with the aid of elastic fiber-rich tissues compensating for the loss of congruity between the joint cartilage surfaces. PMID:26286109

  18. Xenobiotic organic compounds in wastewater

    DEFF Research Database (Denmark)

    Eriksson, Eva; Baun, Anders; Henze, Mogens; Ledin, Anna

    Information regarding the contents of xenobiotic organic compounds (XOCs) in wastewater is limited, but it has been shown that at least 900 different compounds / compound groups could potentially be present in grey wastewater. Analyses of Danish grey wastewater revealed the presence of several...... hundred of XOCs, among them mainly originating from hygiene products: chlorophenols, detergents and phthalates. Several compounds not deriving from hygiene products were also identified e.g. flame-retardants and drugs. A environmental hazard identification showed that a large number of compounds with high...... aquatic toxicity were present and that data for environmental fate could only be retrieved for about half of the compounds....

  19. Nomenclature on an inorganic compound

    International Nuclear Information System (INIS)

    This book contains eleven chapters : which mention nomenclature of an inorganic compound with introduction and general principle on nomenclature of compound. It gives the description of grammar for nomenclature such as brackets, diagonal line, asterisk, and affix, element, atom and groups of atom, chemical formula, naming by stoichiometry, solid, neutral molecule compound, ion, a substituent, radical and name of salt, oxo acid and anion on introduction and definition of oxo acid, coordination compound like symbol of stereochemistry , boron and hydrogen compound and related compound.

  20. Xenobiotic organic compounds in wastewater

    DEFF Research Database (Denmark)

    Eriksson, Eva; Baun, Anders; Henze, Mogens;

    2002-01-01

    Information regarding the contents of xenobiotic organic compounds (XOCs) in wastewater is limited, but it has been shown that at least 900 different compounds / compound groups could potentially be present in grey wastewater. Analyses of Danish grey wastewater revealed the presence of several...... hundred of XOCs, among them mainly originating from hygiene products: chlorophenols, detergents and phthalates. Several compounds not deriving from hygiene products were also identified e.g. flame-retardants and drugs. A environmental hazard identification showed that a large number of compounds with high...... aquatic toxicity were present and that data for environmental fate could only be retrieved for about half of the compounds....

  1. The analysis of adhesively bonded advanced composite joints using joint finite elements

    Science.gov (United States)

    Stapleton, Scott E.

    The design and sizing of adhesively bonded joints has always been a major bottleneck in the design of composite vehicles. Dense finite element (FE) meshes are required to capture the full behavior of a joint numerically, but these dense meshes are impractical in vehicle-scale models where a course mesh is more desirable to make quick assessments and comparisons of different joint geometries. Analytical models are often helpful in sizing, but difficulties arise in coupling these models with full-vehicle FE models. Therefore, a joint FE was created which can be used within structural FE models to make quick assessments of bonded composite joints. The shape functions of the joint FE were found by solving the governing equations for a structural model for a joint. By analytically determining the shape functions of the joint FE, the complex joint behavior can be captured with very few elements. This joint FE was modified and used to consider adhesives with functionally graded material properties to reduce the peel stress concentrations located near adherend discontinuities. Several practical concerns impede the actual use of such adhesives. These include increased manufacturing complications, alterations to the grading due to adhesive flow during manufacturing, and whether changing the loading conditions significantly impact the effectiveness of the grading. An analytical study is conducted to address these three concerns. Furthermore, proof-of-concept testing is conducted to show the potential advantages of functionally graded adhesives. In this study, grading is achieved by strategically placing glass beads within the adhesive layer at different densities along the joint. Furthermore, the capability to model non-linear adhesive constitutive behavior with large rotations was developed, and progressive failure of the adhesive was modeled by re-meshing the joint as the adhesive fails. Results predicted using the joint FE was compared with experimental results for various

  2. The Analysis of Adhesively Bonded Advanced Composite Joints Using Joint Finite Elements

    Science.gov (United States)

    Stapleton, Scott E.; Waas, Anthony M.

    2012-01-01

    The design and sizing of adhesively bonded joints has always been a major bottleneck in the design of composite vehicles. Dense finite element (FE) meshes are required to capture the full behavior of a joint numerically, but these dense meshes are impractical in vehicle-scale models where a course mesh is more desirable to make quick assessments and comparisons of different joint geometries. Analytical models are often helpful in sizing, but difficulties arise in coupling these models with full-vehicle FE models. Therefore, a joint FE was created which can be used within structural FE models to make quick assessments of bonded composite joints. The shape functions of the joint FE were found by solving the governing equations for a structural model for a joint. By analytically determining the shape functions of the joint FE, the complex joint behavior can be captured with very few elements. This joint FE was modified and used to consider adhesives with functionally graded material properties to reduce the peel stress concentrations located near adherend discontinuities. Several practical concerns impede the actual use of such adhesives. These include increased manufacturing complications, alterations to the grading due to adhesive flow during manufacturing, and whether changing the loading conditions significantly impact the effectiveness of the grading. An analytical study is conducted to address these three concerns. Furthermore, proof-of-concept testing is conducted to show the potential advantages of functionally graded adhesives. In this study, grading is achieved by strategically placing glass beads within the adhesive layer at different densities along the joint. Furthermore, the capability to model non-linear adhesive constitutive behavior with large rotations was developed, and progressive failure of the adhesive was modeled by re-meshing the joint as the adhesive fails. Results predicted using the joint FE was compared with experimental results for various

  3. MODELING UNDERGROUND STRUCTURE VULNERABILITY IN JOINTED ROCK

    Energy Technology Data Exchange (ETDEWEB)

    R. SWIFT; D. STEEDMAN

    2001-02-01

    The vulnerability of underground structures and openings in deep jointed rock to ground shock attack is of chief concern to military planning and security. Damage and/or loss of stability to a structure in jointed rock, often manifested as brittle failure and accompanied with block movement, can depend significantly on jointed properties, such as spacing, orientation, strength, and block character. We apply a hybrid Discrete Element Method combined with the Smooth Particle Hydrodynamics approach to simulate the MIGHTY NORTH event, a definitive high-explosive test performed on an aluminum lined cylindrical opening in jointed Salem limestone. Representing limestone with discrete elements having elastic-equivalence and explicit brittle tensile behavior and the liner as an elastic-plastic continuum provides good agreement with the experiment and damage obtained with finite-element simulations. Extending the approach to parameter variations shows damage is substantially altered by differences in joint geometry and liner properties.

  4. Microstructural Characterization of Friction Stir Welded Aluminum-Steel Joints

    Science.gov (United States)

    Patterson, Erin E.; Hovanski, Yuri; Field, David P.

    2016-06-01

    This work focuses on the microstructural characterization of aluminum to steel friction stir welded joints. Lap weld configuration coupled with scribe technology used for the weld tool have produced joints of adequate quality, despite the significant differences in hardness and melting temperatures of the alloys. Common to friction stir processes, especially those of dissimilar alloys, are microstructural gradients including grain size, crystallographic texture, and precipitation of intermetallic compounds. Because of the significant influence that intermetallic compound formation has on mechanical and ballistic behavior, the characterization of the specific intermetallic phases and the degree to which they are formed in the weld microstructure is critical to predicting weld performance. This study used electron backscatter diffraction, energy dispersive spectroscopy, scanning electron microscopy, and Vickers micro-hardness indentation to explore and characterize the microstructures of lap friction stir welds between an applique 6061-T6 aluminum armor plate alloy and a RHA homogeneous armor plate steel alloy. Macroscopic defects such as micro-cracks were observed in the cross-sectional samples, and binary intermetallic compound layers were found to exist at the aluminum-steel interfaces of the steel particles stirred into the aluminum weld matrix and across the interfaces of the weld joints. Energy dispersive spectroscopy chemical analysis identified the intermetallic layer as monoclinic Al3Fe. Dramatic decreases in grain size in the thermo-mechanically affected zones and weld zones that evidenced grain refinement through plastic deformation and recrystallization. Crystallographic grain orientation and texture were examined using electron backscatter diffraction. Striated regions in the orientations of the aluminum alloy were determined to be the result of the severe deformation induced by the complex weld tool geometry. Many of the textures observed in the weld

  5. Microstructural Characterization of Friction Stir Welded Aluminum-Steel Joints

    Science.gov (United States)

    Patterson, Erin E.; Hovanski, Yuri; Field, David P.

    2016-03-01

    This work focuses on the microstructural characterization of aluminum to steel friction stir welded joints. Lap weld configuration coupled with scribe technology used for the weld tool have produced joints of adequate quality, despite the significant differences in hardness and melting temperatures of the alloys. Common to friction stir processes, especially those of dissimilar alloys, are microstructural gradients including grain size, crystallographic texture, and precipitation of intermetallic compounds. Because of the significant influence that intermetallic compound formation has on mechanical and ballistic behavior, the characterization of the specific intermetallic phases and the degree to which they are formed in the weld microstructure is critical to predicting weld performance. This study used electron backscatter diffraction, energy dispersive spectroscopy, scanning electron microscopy, and Vickers micro-hardness indentation to explore and characterize the microstructures of lap friction stir welds between an applique 6061-T6 aluminum armor plate alloy and a RHA homogeneous armor plate steel alloy. Macroscopic defects such as micro-cracks were observed in the cross-sectional samples, and binary intermetallic compound layers were found to exist at the aluminum-steel interfaces of the steel particles stirred into the aluminum weld matrix and across the interfaces of the weld joints. Energy dispersive spectroscopy chemical analysis identified the intermetallic layer as monoclinic Al3Fe. Dramatic decreases in grain size in the thermo-mechanically affected zones and weld zones that evidenced grain refinement through plastic deformation and recrystallization. Crystallographic grain orientation and texture were examined using electron backscatter diffraction. Striated regions in the orientations of the aluminum alloy were determined to be the result of the severe deformation induced by the complex weld tool geometry. Many of the textures observed in the weld

  6. Potential for joint implementation (activities implemented jointly in Kenya)

    Energy Technology Data Exchange (ETDEWEB)

    Mwandoto, Stephen H. [Kenya Meteorological Department, Nairobi (Kenya)

    1999-07-01

    Kenya has ratified the United Framework Convention for Climate Change (UNFCCC) which entered into force on March 21st 1994 and therefore the country is free to participate in Joint Implementation (AIJ) projects. All development projects, activities and services utilise natural resources in one form or another. The technology used in the local industry therefore must be made as efficient as possible so as to provide a much higher output of saleable goods and services from the same resource base in order to reduce wastes in the form of pollutants in gaseous, liquids or solid forms. The 8th Kenya National Development Plan, the 1996 Sessional Paper on Industrialisation, the National Environmental Action Plan and the draft National Environmental policy paper have clearly defined the policy initiatives on acquisition of efficient manufacturing production processes to protect the resource base. What is now required is the implementation of those policy initiatives by application of the best available and affordable technology to maximise trade and investments. In this paper, the potential for investments in alternative energy technologies and energy efficiency in Medium and Small Scale enterprises in Kenya is discussed. (Author)

  7. Interfacial structure and joint strengthening in arc brazed galvanized steels with copper based filler

    Institute of Scientific and Technical Information of China (English)

    LI Rui-feng; YU Zhi-shui; QI Kai

    2006-01-01

    Galvanized steel sheets were joined by tungsten inert gas(TIG) and metal inert gas(MIG) brazing process using copper based filler. The results show that the joint zone hardness is higher than that of the base material or copper filler from the microhardness tests of TIG brazing specimens, and the fracture spot is at the base materials zone from the tensile tests of MIG brazing specimens. Examination using energy dispersive X-ray analysis reveals the presence of intermetallic compound Fe5Si3(Cu) in the joint. The dispersal of fine Fe5Si3(Cu) particles is the main strengthening factor for the joint. The Fe5Si3(Cu) particles are determined to arise from three sources, namely, spot micro-melt, whisker-like fragmentation and dissolve-separation actions.

  8. The subtalar joint complex of Australopithecus sediba.

    Science.gov (United States)

    Prang, Thomas C

    2016-01-01

    The hominin talus has figured prominently in previous studies of the functional morphology of the talocrural joint, but the talocalcaneal and talonavicular joints have received comparatively less attention despite their functional importance as components of the subtalar joint complex. An associated complete talus and calcaneus attributed to the Malapa Hominin 2 (MH2) individual of Australopithecus sediba offers the opportunity to evaluate the subtalar joint complex in an early hominin. Furthermore, detailed morphological comparisons of A. sediba to other fossil hominins such as Australopithecus africanus have not yet been conducted. Here I quantify joint curvatures and angular measurements among extant hominoids and fossil hominins to evaluate the functional morphology of the subtalar joint complex of A. sediba. Australopithecus sediba uniquely combines talocalcaneal joint morphology indicative of mobility with specializations of the talonavicular joint that provide medial midtarsal stabilization. Multivariate analyses of talus and calcaneus variables show that A. sediba is most similar to extant gorillas in the morphology of the subtalar joint complex. In contrast, other hominins, such as OH 8, are more similar to modern humans. The morphological similarity between MH2 (U.W. 88-98/99) and specimens from Sterkfontein, Member 4 (StW 88, StW 102, StW 352) in morphologies of the talonavicular and talocalcaneal joints suggests that A. sediba may have possessed a foot that was functionally similar to that of A. africanus. This combination of morphologies in the A. sediba foot is probably derived among hominins and suggests that arboreality may have been adaptively significant for southern African Australopithecus. PMID:26767963

  9. Analysis on the joint tensile strength and fractography of TiNi shape memory alloy precise pulse resistance butt welding

    Institute of Scientific and Technical Information of China (English)

    赵熹华; 韩立军; 赵蕾

    2002-01-01

    This paper studies mechanical property and fractography of the welded joints obtained in different welding parameters such as welding heat and welding press with/without gas shield in TiNi shape memory alloy precise pulse resistance butt welding using tensile strength test, XRD, SEM and TEM measures. The optimum welding parameters obtaining high tensile strength welded joint are got. On the condition of welding press magneting current 2 A and welding heat 75%, the joint strength is the highest. This is important for to study other properties of TiNi shape memory alloy further. The experimental results state that argon gas shield have different effects on different welding parameters, less on welding press, but great on welding heat. But excessive welding press and welding heat have great effects on joint tensile strength. Too high welding heat can produce the new intermetallic compound, this intermetallic compound lead to dislocation density to increase and form the potential crack initiation, which can easily make the joint fracture under stress effect and decrease the shape memory ratio of joint for high density dislocation groups existing in the twinned martensite.

  10. Impact extractive fracture of jointed steel plates of a bolted joint

    Directory of Open Access Journals (Sweden)

    Ambarita H.

    2012-08-01

    Full Text Available This study is concerned with the development of a fracture criterion for the impact fracture of jointed steel plates of a bolted joint used in a car body. For the accurate prediction of crash characteristics of car bodies by computer-aided engineering (CAE, it is also necessary to examine the behavior and fracture of jointed steel plates subjected to impact loads. Although the actual impact fracture of jointed steel plates of a bolted joint used in cars is complicated, for simplifying the problem it might be classified into the shear fracture and the extractive fracture of jointed steel plates. Attention is given to the extractive fracture of jointed steel plates in this study. The extractive behavior and fracture of three kinds of steel plates used for cars are examined in experiments and numerical simulations. The impact extraction test of steel plates jointed by a bolt is performed using the one-bar method, together with the static test. In order to understand the mechanism of extractive fracture process of jointed steel plates, numerical simulations by a FEM code LS-DYNA are also carried out. The obtained results suggest that a stress-based fracture criterion may be developed for the impact extractive fracture of jointed steel plates of a bolted joint used in a car body.

  11. Magnetic suspension hip joint: an ideal design of an artificial joint

    Institute of Scientific and Technical Information of China (English)

    DAI Min; NIE Tao

    2010-01-01

    Background Artificial joints present certain problems such as osteal absorption and lysis induced by wear debris which leads to loosening of the prosthesis over a period of time. Here we propose a design of an artificial magnetic suspension joint that was prepared by integrating the medical theories of modern material science, magnetism, and medical physics.Methods According to clinical characteristic of biological and mechanical for hip joint, we designed the appearance and dimensions of magnetic suspension joint and placed neodymium-iron-boron permanent magnets in the prosthesis.As the same time, we performed mechanical and biological experiments using artificial magnetic suspension hip joints models.Results By simulated the human hip structure and the external load, we discovered the artificial magnetic suspension hip joints models had much lesser amount and size of wear debris than the ceramic/ceramic artificial hip joint prosthesis in friction wear tests. The force between the artificial joints with magnetic materials that we have calculated is feasible for application of artificial joint. The design of artificial magnetic suspension hip joints models was plausible technically and safe biologically.Conclusion Artificial magnetic suspension hip joints may effectively reduce the incidence of the loosening of prosthesis over a period of time.

  12. MR assessment of distribution and amount of joint effusion in patients with traumatic knee joint disorders

    International Nuclear Information System (INIS)

    To clarify the distribution of joint effusion, and the relationship between type of injury and amount of joint effusion seen in traumatic knee joint magnetic resonance imaging (MRI). We retrospectively reviewed the MR images of 400 patients with traumatic knee joint effusion. The knee joint space was divided into four compartments : central portion (para-ACL, para-PCL), suprapatellar pouch, posterior femoral recess, and subpopliteal recess, and we then compared the amount and distribution of effusion. For statistical analysis, the chi-square test was used. Among 400 MRI examinations of joint effusion, 383 knees (96%) showed homogeneous low intensity on T1-weighted images, and - except for ten cases of fluid-fluid levels- homogeneous high intensity on T2-weighted images. Knee joint effusion was clearly shown to be distributed mainly in the suprapatellar pouch (345, 86%), followed by the central posterior femoral recess, and the subpopliteal recess (P<0.001). Extensive joint effusion was less frequently found in the normal group, but was occasionally found in the combined injury group (P<0.001). The relationship between amount of joint effusion and type of injury was statistically significant (P<0.001), except in the case of medial and lateral collateral ligament injury. The distribution of joint effusion in patients with traumatic knee disorders is a reflection of anatomic communication, and whether the amount of joint effusion was small or large depended on the anatomical location and type of injury

  13. Ultrasonic evaluation of friction stud welded AA 6063/AISI 1030 steel joints

    International Nuclear Information System (INIS)

    Highlights: • Friction stud welding of AA 6063 and AISI 1030 was done successfully. • Ultrasonic evaluation of interfacial properties. • EDX analysis confirms intermetallic compound (FeAl) in the interfacial region. - Abstract: Friction stud welding is a promising technique in many applications related to oil and gas industries. It is used to attach grating to offshore oil platforms in areas where arc welding is not permitted because of the risk of causing a fire or explosion. Attachment of anodes inside seawater discharge pipelines in a gas processing plant is performed by this process. This solid state joining process permits metal combinations such as welding of aluminum studs to steel which would be problematic with arc welding because of the formation of thick and brittle inter-metallic compounds. In the present work, AA 6063 is joined to AISI 1030 steel using friction stud welding machine. Properties that are of interest to manufacturing applications such as Young’s modulus, longitudinal velocity, bulk modulus and shear modulus are evaluated by means of an ultrasonic flaw detector. At the interface of the joint, there is an increase of 4.4%, 1.8%, 1.15% and 4.42% is observed for the properties Young’s modulus, longitudinal velocity, bulk modulus and shear modulus respectively. This is due to the formation of intermetallic compound and increase in hardness at the interfacial region. Energy Dispersive X-ray analysis confirms the presence of FeAl as the intermetallic compound. Scanning Electron Microscope evaluation shows the presence of an unbound zone at the center of the inner region which is due to the minimum rotational speed and low axial load experienced at that point. In the unbound zone, there is an incomplete bond between dissimilar metals and it is detrimental to joint strength. Optimum value of friction time and usage of pure aluminum interlayer during the friction stud welding process hinders the formation of unbound zone and enhances the

  14. Joint shear strength of FRP reinforced concrete beam-column joints

    Science.gov (United States)

    Saravanan, Jagadeesan; Kumaran, Ganapathy

    2011-03-01

    An assessment of the joint shear strength of exterior concrete beam-column joints reinforced internally with Glass Fibre Reinforced Polymer (GFRP) reinforcements under monotonically increasing load on beams keeping constant load on columns is carried out in this study. Totally eighteen numbers of specimens are cast and tested for different parametric conditions like beam longitudinal reinforcement ratio, concrete strength, column reinforcement ratio, joint aspect ratio and influence of the joint stirrups at the joint. Also finite element analysis is performed to simulate the behaviour of the beam-column joints under various parametric conditions. Based on this study, a modified design equation is proposed for assessing the joint shear strength of the GFRP reinforced beam-column specimens based on the experimental results and the review of the prevailing design equations.

  15. Offset Compound Gear Drive

    Science.gov (United States)

    Stevens, Mark A.; Handschuh, Robert F.; Lewicki, David G.

    2010-01-01

    The Offset Compound Gear Drive is an in-line, discrete, two-speed device utilizing a special offset compound gear that has both an internal tooth configuration on the input end and external tooth configuration on the output end, thus allowing it to mesh in series, simultaneously, with both a smaller external tooth input gear and a larger internal tooth output gear. This unique geometry and offset axis permits the compound gear to mesh with the smaller diameter input gear and the larger diameter output gear, both of which are on the same central, or primary, centerline. This configuration results in a compact in-line reduction gear set consisting of fewer gears and bearings than a conventional planetary gear train. Switching between the two output ratios is accomplished through a main control clutch and sprag. Power flow to the above is transmitted through concentric power paths. Low-speed operation is accomplished in two meshes. For the purpose of illustrating the low-speed output operation, the following example pitch diameters are given. A 5.0 pitch diameter (PD) input gear to 7.50 PD (internal tooth) intermediate gear (0.667 reduction mesh), and a 7.50 PD (external tooth) intermediate gear to a 10.00 PD output gear (0.750 reduction mesh). Note that it is not required that the intermediate gears on the offset axis be of the same diameter. For this example, the resultant low-speed ratio is 2:1 (output speed = 0.500; product of stage one 0.667 reduction and stage two 0.750 stage reduction). The design is not restricted to the example pitch diameters, or output ratio. From the output gear, power is transmitted through a hollow drive shaft, which, in turn, drives a sprag during which time the main clutch is disengaged.

  16. Compound semiconductor integrated circuits

    CERN Document Server

    Vu, Tho T

    2003-01-01

    This is the book version of a special issue of the International Journal of High Speed Electronics and Systems , reviewing recent work in the field of compound semiconductor integrated circuits. There are fourteen invited papers covering a wide range of applications, frequencies and materials. These papers deal with digital, analog, microwave and millimeter-wave technologies, devices and integrated circuits for wireline fiber-optic lightwave transmissions, and wireless radio-frequency microwave and millimeter-wave communications. In each case, the market is young and experiencing rapid growth

  17. Titanium alkoxide compound

    Science.gov (United States)

    Boyle, Timothy J.

    2007-08-14

    A titanium alkoxide composition is provided, as represented by the chemical formula (OC.sub.6H.sub.5N).sub.2Ti(OC.sub.6H.sub.5NH.sub.2).sub.2. As prepared, the compound is a crystalline substance with a hexavalent titanium atom bonded to two OC.sub.6H.sub.5NH.sub.2 groups and two OC.sub.6H.sub.5N groups with a theoretical molecular weight of 480.38, comprising 60.01% C, 5.04% H and 11.66% N.

  18. Phase constitution in the interfacial region of laser penetration brazed magnesium–steel joints

    International Nuclear Information System (INIS)

    The phase constitution in the interfacial region of laser penetration brazed magnesium–steel joints was investigated using electron microscopy. From the distribution of elements, the transition zone was mainly composed of elements Mg and Fe along with some Al and O. Furthermore, the transition layer consisted mainly of intermetallic compounds and metal oxides. The compounds were identified as Al-rich phases, such as Mg17Al12, Mg2Al3, FeAl and Fe4Al13. More noteworthy was that the thickness of the transition layer was determined by Fe–Al compounds. The presence of FeAl and Fe4Al13 was a result of the complex processes that were associated with the interfacial reaction of solid steel and liquid Mg–Al alloy. - Highlights: • A technology of laser penetration brazed Mg alloy and steel has been developed. • The interface of Mg/Fe dissimilar joints was investigated using electron microscopy. • The transition layer consisted of intermetallic compounds and metal oxides. • Moreover, the thickness of transition layer was determined by Fe/Al compounds. • The presence of FeAl and Fe4Al13 was associated with the interfacial reaction

  19. Phase constitution in the interfacial region of laser penetration brazed magnesium–steel joints

    Energy Technology Data Exchange (ETDEWEB)

    Miao, Yugang; Han, Duanfeng, E-mail: handuanfeng@gmail.com; Xu, Xiangfang; Wu, Bintao

    2014-07-01

    The phase constitution in the interfacial region of laser penetration brazed magnesium–steel joints was investigated using electron microscopy. From the distribution of elements, the transition zone was mainly composed of elements Mg and Fe along with some Al and O. Furthermore, the transition layer consisted mainly of intermetallic compounds and metal oxides. The compounds were identified as Al-rich phases, such as Mg{sub 17}Al{sub 12}, Mg{sub 2}Al{sub 3}, FeAl and Fe{sub 4}Al{sub 13}. More noteworthy was that the thickness of the transition layer was determined by Fe–Al compounds. The presence of FeAl and Fe{sub 4}Al{sub 13} was a result of the complex processes that were associated with the interfacial reaction of solid steel and liquid Mg–Al alloy. - Highlights: • A technology of laser penetration brazed Mg alloy and steel has been developed. • The interface of Mg/Fe dissimilar joints was investigated using electron microscopy. • The transition layer consisted of intermetallic compounds and metal oxides. • Moreover, the thickness of transition layer was determined by Fe/Al compounds. • The presence of FeAl and Fe{sub 4}Al{sub 13} was associated with the interfacial reaction.

  20. Catalytic properties of niobium compounds

    International Nuclear Information System (INIS)

    The catalytic activity and selectivity of niobium compounds including oxides, salts, organometallic compounds and others are outlined. The application of these compounds as catalysts to diversified reactions is reported. The nature and action of niobium catalysts are characteristic and sometimes anomalous, suggesting the necessity of basic research and the potential use as catalysts for important processes in the chemical industry. (Author)

  1. Gulf Canada's Russian joint venture

    International Nuclear Information System (INIS)

    After three years of evaluating prospects and negotiating with government and industry representatives, Gulf Canada established its first joint venture in the Russian Federation with Komineft, a production association from the Komi autonomous republic. Komineft has a 50% share of the venture, and the rest is shared equally between Gulf and British Gas. The operating area is at the Vozey and Upper Vozey fields in the Timan-Pechora Basin, some 1,500 km northeast of Moscow just inside the Arctic Circle. An attractive feature of the Upper Vozey project is low development costs of ca $2/bbl. In the Vozey field, the venture will set up an enhanced oil recovery demonstration project to test techniques perfected in Alberta. About 60 Canadians are involved on the project, and headquarters are in Usinsk, ca 100 km south of the oil fields. In the first half of 1992, oil production in the first phase of the venture averaged around 10,000 bbl/d and continues to increase

  2. The Joint COntrols Project Framework

    CERN Document Server

    González-Berges, M

    2003-01-01

    The Framework is one of the subprojects of the Joint COntrols Project (JCOP), which is collaboration between the four LHC experiments and CERN. By sharing development, this will reduce the overall effort required to build and maintain the experiment control systems. As such, the main aim of the Framework is to deliver a common set of software components, tools and guidelines that can be used by the four LHC experiments to build their control systems. Although commercial components are used wherever possible, further added value is obtained by customisation for HEP-specific applications. The supervisory layer of the Framework is based on the SCADA tool PVSS, which was selected after a detailed evaluation. This is integrated with the front-end layer via both OPC (OLE for Process Control), an industrial standard, and the CERN-developed DIM (Distributed Information Management System) protocol. Several components are already in production and being used by running fixed-target experiments at CERN as well as for th...

  3. Aksa plans polypropylene joint venture

    International Nuclear Information System (INIS)

    Turkish acrylic fiber maker Aksa (Yalova), part of the Akkok textile conglomerate, is studying construction of a world-scale polypropylene (PP) plant as part of its diversification plans. The company says it is engaged in discussions with three 'multinations in the PP business' on the possibility of a joint venture. One of the firms is understood to be Amoco. Aksa is looking at three possible locations for the 100,000 m.t.-150,000 m.t./year plant: Yalova, near Istanbul, where its existing plants are located; Zonguldak, on the Black Sea coast; and within one of the existing complexes or a new site belonging to state-owned Petkim. Aksa has not yet discussed that option with Petkim, which recently received approval to build a $2.5-billion petrochemical complex. The Aksa PP plant would cost about $100 million and would use propylene from world markets. The onstream date depends on Aksa's ability to link up with a foreign partner, but it hopes to complete the unit within three years. Turkey has only one PP plant, a 65,000-m.t./year Petkim unit at Aliaga. The domestic market is currently two to three times that amount and is growing. Petkim also plans a 200,000-m.t./year PP plant as part of its new complex

  4. Goldenphilicity: Luminescent gold compounds

    International Nuclear Information System (INIS)

    In the solids and molecules different types of bonds are presented depending on the involved atoms, covalent bonds are common among elements of open shell, where more bond orbitals are filled than anti bond orbitals. It is expected that ionic bonds among closed shell atoms which have charges of opposite sign. Bonds type Van der Waals are presented among molecules which have a bipolar moment. It would not be expected bonds among zero charge species, or more generally with the same nominal charge and in any case the attractive forces would be very small. In fact it is expected that two metallic cations to be repelled each other. There recently is evidence that in organic or organometallic compounds could exist attractive interactions between two cations of the d8 -d10 -s2 families. These bonds are weak but stronger than those of Van der Waals. They are compared with the hydrogen bonds. In this work it was reviewed some examples in which the goldenphilicity plays an important role in the luminescence that the gold complexes present. Examples of mono, bi and trinuclear and the structures that these organometallic compounds could take are examined. (Author)

  5. Progressive Damage Analysis of Bonded Composite Joints

    Science.gov (United States)

    Leone, Frank A., Jr.; Girolamo, Donato; Davila, Carlos G.

    2012-01-01

    The present work is related to the development and application of progressive damage modeling techniques to bonded joint technology. The joint designs studied in this work include a conventional composite splice joint and a NASA-patented durable redundant joint. Both designs involve honeycomb sandwich structures with carbon/epoxy facesheets joined using adhesively bonded doublers.Progressive damage modeling allows for the prediction of the initiation and evolution of damage within a structure. For structures that include multiple material systems, such as the joint designs under consideration, the number of potential failure mechanisms that must be accounted for drastically increases the complexity of the analyses. Potential failure mechanisms include fiber fracture, intraply matrix cracking, delamination, core crushing, adhesive failure, and their interactions. The bonded joints were modeled using highly parametric, explicitly solved finite element models, with damage modeling implemented via custom user-written subroutines. Each ply was discretely meshed using three-dimensional solid elements. Layers of cohesive elements were included between each ply to account for the possibility of delaminations and were used to model the adhesive layers forming the joint. Good correlation with experimental results was achieved both in terms of load-displacement history and the predicted failure mechanism(s).

  6. MANAGEMENT OF JOINT DISORDERS BY KSHEERAVASTI

    Directory of Open Access Journals (Sweden)

    Shingade Vijay P.

    2011-02-01

    Full Text Available Now a days joint disorders are the most commonly occuring in the world. Sandhigata Vata, Vata rakta, Amavata are the common joint disorders. In dhatukshayajanya sandhigata vata and vata rakta, ksheera vasti is helpful. Common symptoms of joint disorders are: Asthishoola, Sandhishoola, Sandhisodha, restriction of movements, pain on movement. Though there are several joint disorders, majority of joint disorders are due to vitiation of vata dosha. Hence, vasti is considered as the main treatment for vata dosha. Specially in dhatukshayajanya conditions, vasti with medicated milk is very useful. Cow milk is the best among all milks. It has same properties like ojas, thus increases ojas. Ksheera is considered as the best in nourishing the asthi dhatu because of its tulyaguna, thus controls the vata dosha. Milk has Snigdha, guru, bahala properties which are similar to that of asthidhatu (tulyaguna. Thus, it counters the rukshatwa and sclerosing effects of bone and increases the unctousness of joint. It also nourishes the asthidhatu and prevents the bone from osteoporosis. Most joint disorders are due to deficiency of calcium content of bone tissue. Milk contains calcium. So, by giving Ksheera vasti calcium content of bone can be increased. Milk contains almost all minerals needed by the body, Such as Ca, P, Na, K, Mg, Cu, I, Cobalt etc, but particularly it is rich in Ca.

  7. Flexible joints in structural and multibody dynamics

    Directory of Open Access Journals (Sweden)

    O. A. Bauchau

    2013-02-01

    Full Text Available Flexible joints, sometimes called bushing elements or force elements, are found in all structural and multibody dynamics codes. In their simplest form, flexible joints simply consist of sets of three linear and three torsional springs placed between two nodes of the model. For infinitesimal deformations, the selection of the lumped spring constants is an easy task, which can be based on a numerical simulation of the joint or on experimental measurements. If the joint undergoes finite deformations, identification of its stiffness characteristics is not so simple, specially if the joint is itself a complex system. When finite deformations occur, the definition of deformation measures becomes a critical issue. This paper proposes a family of tensorial deformation measures suitable for elastic bodies of finite dimension. These families are generated by two parameters that can be used to modify the constitutive behavior of the joint, while maintaining the tensorial nature of the deformation measures. Numerical results demonstrate the objectivity of the deformations measures, a feature that is not shared by the deformations measures presently used in the literature. The impact of the choice of the two parameters on the constitutive behavior of the flexible joint is also investigated.

  8. Versican Expression during Synovial Joint Morphogenesis

    Directory of Open Access Journals (Sweden)

    John B. Shepard, Heidi A. Krug, Brooklynn A. LaFoon, Stanley Hoffman, Anthony A. Capehart

    2007-01-01

    Full Text Available The extracellular matrix (ECM plays a critical role in governing cell behavior and phenotype during limb skeletogenesis. Chondroitin sulfate proteoglycans (Cspgs are highly expressed in the ECM of precartilage mesenchymal condensations and are important to limb chondrogenesis and cartilage structure, but little is known regarding their involvement in formation of synovial joints in the embryonic limb. Matrix versican Cspg expression has previously been reported in the epiphysis of developing long bones and presumptive joint; however, detailed analysis has not yet been conducted. In the present study we immunolocalized versican and aggrecan Cspgs during chick elbow joint morphogenesis between HH st25-41 of development. In this study we show that versican and aggrecan expression initially overlapped in the incipient cartilage model of long bones in the wing, but versican was also highly expressed in the perichondrium and presumptive joint interzone during early stages of morphogenesis (HH st25-34. By HH st36-41 versican localization was restricted to the future articular surfaces of the developing joint and surrounding joint capsule while aggrecan localized in an immediately adjacent and predominately non-overlapping region of chondrogenic cells at the epiphyses. These results suggest a potential role for versican proteoglycan in development and maintenance of the synovial joint interzone.

  9. Interface microstructural control by probe length adjustment in friction stir welding of titanium and steel lap joint

    International Nuclear Information System (INIS)

    Highlights: • The titanium and steel were tightly bonded together. • The joint interface microstructure was well controlled by parameter adjustment. • Both of non-intermixed and intermixed joint interfaces were observed. • The joint interfaces were consisted of β-Ti and Fe–Ti intermetallic compound. - Abstract: The dissimilar lap joining of commercially pure Ti (CP-Ti) plate of 1.0 mm in thickness and structural steel (SPCC) plate of 3.2 mm in thickness was conducted by friction stir welding using different tools with probe lengths from 0.8 to 1.2 mm for the purpose of controlling the joint interface microstructure. The sound joints showing the base plate fracture of CP-Ti have been obtained by using the tools with the probe lengths of 0.9 and 1.0 mm. The transmission electron microscope examination revealed the two types of the interface microstructure. One was a non-intermixed type interface with a single interlayer of about 50–100 nm in thickness, composed of FeTi intermetallic compound and β-Ti phase at the joint with the probe length of 0.9 mm. The other was an intermixed interface with lamellar structure in which a FeTi or FeTi + Fe2Ti intermetallic compound layer of about 100 nm in thickness and a β-Ti layer of about 1 μm in thickness were alternately formed at the joint with the probe length of 1.0 mm

  10. Real-time visualization of joint cavitation.

    Directory of Open Access Journals (Sweden)

    Gregory N Kawchuk

    Full Text Available Cracking sounds emitted from human synovial joints have been attributed historically to the sudden collapse of a cavitation bubble formed as articular surfaces are separated. Unfortunately, bubble collapse as the source of joint cracking is inconsistent with many physical phenomena that define the joint cracking phenomenon. Here we present direct evidence from real-time magnetic resonance imaging that the mechanism of joint cracking is related to cavity formation rather than bubble collapse. In this study, ten metacarpophalangeal joints were studied by inserting the finger of interest into a flexible tube tightened around a length of cable used to provide long-axis traction. Before and after traction, static 3D T1-weighted magnetic resonance images were acquired. During traction, rapid cine magnetic resonance images were obtained from the joint midline at a rate of 3.2 frames per second until the cracking event occurred. As traction forces increased, real-time cine magnetic resonance imaging demonstrated rapid cavity inception at the time of joint separation and sound production after which the resulting cavity remained visible. Our results offer direct experimental evidence that joint cracking is associated with cavity inception rather than collapse of a pre-existing bubble. These observations are consistent with tribonucleation, a known process where opposing surfaces resist separation until a critical point where they then separate rapidly creating sustained gas cavities. Observed previously in vitro, this is the first in-vivo macroscopic demonstration of tribonucleation and as such, provides a new theoretical framework to investigate health outcomes associated with joint cracking.

  11. Ultra-high-vacuum tight transition joints of titanium-stainless steel produced by explosive tube to tube welding

    International Nuclear Information System (INIS)

    The parameters for explosive welding of Stainless Steel to Titanium were determined with the objective to avoid intermetallic compounds and tubular needles at the interface. The optimum parameters were applied for the production of tubular transition joints between Titanium and stainless steel for ultra high vacuum applications. Prototypes were examined mechanically and by metallographic methods and tested under ultra high varuum conditions. An extraordinary mechanical strength of the connection was found, and, in contrary to transition joints, produced by other means, not a single leak occurred in joints fabricated by concentric explosive cladding. Transition joints of the described type were used in laboratories and in the ultra-high-vacuum system of the ISR. (orig.)

  12. Knee joint vibroarthrographic signal processing and analysis

    CERN Document Server

    Wu, Yunfeng

    2015-01-01

    This book presents the cutting-edge technologies of knee joint vibroarthrographic signal analysis for the screening and detection of knee joint injuries. It describes a number of effective computer-aided methods for analysis of the nonlinear and nonstationary biomedical signals generated by complex physiological mechanics. This book also introduces several popular machine learning and pattern recognition algorithms for biomedical signal classifications. The book is well-suited for all researchers looking to better understand knee joint biomechanics and the advanced technology for vibration arthrometry. Dr. Yunfeng Wu is an Associate Professor at the School of Information Science and Technology, Xiamen University, Xiamen, Fujian, China.

  13. Joint hypermobility and fibromyalgia in schoolchildren.

    OpenAIRE

    Gedalia, A; Press, J.; Klein, M.; Buskila, D.

    1993-01-01

    OBJECTIVES--To test the hypothesis that joint hypermobility may play a part in the pathogenesis of pain in fibromyalgia, schoolchildren were examined for the coexistence of joint hypermobility and fibromyalgia. METHODS--The study group consisted of 338 children (179 boys, 159 girls; mean age 11.5 years, range 9-15 years) from one public school in Beer-Sheva, Israel. In the assessment of joint hypermobility, the criteria devised by Carter and Bird were used. Any child who met at least three of...

  14. Traumatic injuries of the temporomandibular joint

    International Nuclear Information System (INIS)

    Injuries of the temporomandibular joint are mostly due to injuries or fractures of the mandibular condyle. Fractures of the skull base involving the temporomandibular joint are rare. Classification of fractures refers to their anatomical positions and the presence or absence of a luxation. Further, it is important whether the fracture is intra- or extra-capsular. The primary imaging method should be orthopantomography. As for therapy planning, especially surgery, also evaluation of soft tissue is necessary, computed tomography is the imaging method of choice. For diagnosis of complications or internal derangement of the temporomandibular joint, magnetic resonance imaging is to be recommended. (orig.)

  15. Uncertainty reconciles complementarity with joint measurability

    International Nuclear Information System (INIS)

    The fundamental principles of complementarity and uncertainty are shown to be related to the possibility of joint unsharp measurements of pairs of noncommuting quantum observables. A joint measurement scheme for complementary observables is proposed. The measured observables are represented as positive operator valued measures (POVMs), whose intrinsic fuzziness parameters are found to satisfy an intriguing pay-off relation reflecting the complementarity. At the same time, this relation represents an instance of a Heisenberg uncertainty relation for measurement imprecisions. A model-independent consideration shows that this uncertainty relation is logically connected with the joint measurability of the POVMs in question

  16. Semiconducting III-V compounds

    CERN Document Server

    Hilsum, C; Henisch, Heinz R

    1961-01-01

    Semiconducting III-V Compounds deals with the properties of III-V compounds as a family of semiconducting crystals and relates these compounds to the monatomic semiconductors silicon and germanium. Emphasis is placed on physical processes that are peculiar to III-V compounds, particularly those that combine boron, aluminum, gallium, and indium with phosphorus, arsenic, and antimony (for example, indium antimonide, indium arsenide, gallium antimonide, and gallium arsenide).Comprised of eight chapters, this book begins with an assessment of the crystal structure and binding of III-V compounds, f

  17. Poisson-Gumbel Mixed Compound Distribution and its application

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    With the development of offshore engineering, the joint probability study for extreme sea environments has been a subject of increasing interest for both mathematicians and engineers. However, the conventional multivariate probability distribution models do not describe the distribution of the occurrences of extreme sea states induced by typhoon, hurricane or winter storm, and thus fail to reflect the probability characteristics of sea environments in all the aspects. Extreme sea environments are typically to be found in storms like typhoon, and the occurrences of such storms in certain sea areas, varying from year to year, may be fitted to a discrete distribution. By compounding the discrete distribution with a bivariate continuous distribution of two extreme sea environments, a new kind of distribution--Bivariate Compound Extreme Value Distribution (BCEVD) is obtained in this note. This study proposes Poisson-Gum- bel Mixed Compound Distribution, one of the particular forms of BCEVD, and gives an example of its application by using it to compute the joint distribution of wind velocities and wave heights and to estimate the 100-year return level, based on the 20-year wind and wave data in the East China Sea. The results show the advantage of PGMCD model in its stable results and simple use.

  18. Volatile organic compounds

    International Nuclear Information System (INIS)

    The goal is: Not more emission of volatile organic compounds (VOCs) than necessary. The items discussed in this presentation are the VOCs, how to calculate emission of VOCs, how to reduce or avoid them, and different recovery processes. The largest source of Norwegian emissions of non methane VOCs (NMVOCs) is offshore loading of raw petroleum. Emissions of VOCs should be reduced mainly for two reasons: (1) on sunny days NMVOCs may react with NOx to form ozon and smog close to the surface, (2) ozone and smog close to the surface may be harmful to plants and animals, and they are hazardous to human health. As for the calculation of VOC emissions, the VOCON project will release the calculation program HCGASS in 1999. This project is a cooperative project headed by SINTEF/Marintek

  19. Synthesis of labeled compounds

    International Nuclear Information System (INIS)

    Intermediate compounds labeled with 13C included methane, sodium cyanide, methanol, ethanol, and acetonitrile. A new method for synthesizing 15N-labeled 4-ethylsulfonyl-1-naphthalene-sulfonamide was developed. Studies were conducted on pathways to oleic-1-13C acid and a second pathway investigated was based on carbonation of 8-heptadecynylmagnesium bromide with CO2 to prepare sterolic acid. Biosynthetic preparations included glucose-13C from starch isolated from tobacco leaves following photosynthetic incubation with 13CO2 and galactose-13C from galactosylglycerol-13C from kelp. Research on growth of organisms emphasized photosynthetic growth of algae in which all cellular carbon is labeled. Preliminary experiments were performed to optimize the growth of Escherichia coli on sodium acetate-13C

  20. Microoptical telescope compound eye.

    Science.gov (United States)

    Duparré, Jacques; Schreiber, Peter; Matthes, André; Pshenay-Severin, Ekaterina; Bräuer, Andreas; Tünnermann, Andreas; Völkel, Reinhard; Eisner, Martin; Scharf, Toralf

    2005-02-01

    A new optical concept for compact digital image acquisition devices with large field of view is developed and proofed experimentally. Archetypes for the imaging system are compound eyes of small insects and the Gabor-Superlens. A paraxial 3x3 matrix formalism is used to describe the telescope arrangement of three microlens arrays with different pitch to find first order parameters of the imaging system. A 2mm thin imaging system with 21x3 channels, 70 masculinex10 masculine field of view and 4.5mm x 0.5mm image size is optimized and analyzed using sequential and non-sequential raytracing and fabricated by microoptics technology. Anamorphic lenses, where the parameters are a function of the considered optical channel, are used to achieve a homogeneous optical performance over the whole field of view. Captured images are presented and compared to simulation results. PMID:19494951

  1. Scintigraphy in evaluating avascular joint disease and joint prostheses

    International Nuclear Information System (INIS)

    Interruption of blood flow to the femoral head may occur as a result of trauma, medications, underlying small vessel disease or as an idiopathic process of unclear etiology. Tetracycline fluorescence of bone tissue specimens is a well-established method of determining relative bone blood flow but is poorly suited as a noninvasive or preoperative procedure. sup(99m)Tc sulfur colloid has also been used to demonstrate femoral head reticuloendothelial elements and thereby indirectly establish the presence or absence of blood supply, however, this method lacks specificity. It has been documented that 18F and, to a great extent, sup(99m)Tc phosphate compounds localize in bone as a direct function of bone blood flow. Since the radiation dose associated with sup(99m)Tc phosphates is modest and excellent images with fine detail can be obtained using the Anger camera and pinhole collimator, this technique has become the method of choice for noninvasive evaluation of vascularity of the femoral head. Specific clinical applications are presented in this chapter. (Auth.)

  2. Radiodiagnostics of the temporomandibular joint of disorders

    International Nuclear Information System (INIS)

    Temporomandibularis disorders have a multifactorial etiology with very variable clinical symptoms. On the X-ray image can see the configuration of the joint structures correctly or TMJ disorders ( luxation, subluxation, arthrosis). (authors)

  3. Structural dynamic analysis of a ball joint

    Science.gov (United States)

    Hwang, Seok-Cheol; Lee, Kwon-Hee

    2012-11-01

    Ball joint is a rotating and swiveling element that is typically installed at the interface between two parts. In an automobile, the ball joint is the component that connects the control arms to the steering knuckle. The ball joint can also be installed in linkage systems for motion control applications. This paper describes the simulation strategy for a ball joint analysis, considering manufacturing process. Its manufacturing process can be divided into plugging and spinning. Then, the interested responses is selected as the stress distribution generated between its ball and bearing. In this paper, a commercial code of NX DAFUL using an implicit integration method is introduced to calculate the response. In addition, the gap analysis is performed to investigate the fitness, focusing on the response of the displacement of a ball stud. Also, the optimum design is suggested through case studies.

  4. Elbow joint instability: A kinematic model.

    Science.gov (United States)

    Olsen, B S; Henriksen, M G; Søjbjerg, J O; Helmig, P; Sneppen, O

    1994-05-01

    The effect of simultaneous ulnar and radial collateral ligament division on the kinematics of the elbow joint is studied in a cadaveric model. Severance of the anterior part of the ulnar collateral ligament and the annular ligament led to significant elbow joint instability in valgus and varus stress and in forced external and internal rotation. The mean maximum laxity in valgus stress and forced external rotation were 5.7° and 13.2°. The forearms of the elbow joint specimens were transfixed in maximum pronation. During valgus and varus stress the corresponding spontaneous ulnar rotation of the specimens was recorded. The reproducibility of the instability pattern suggests that this model is suitable for evaluating stabilizing procedures aimed at correction of elbow joint instability before these procedures are introduced into patient care. PMID:22959690

  5. Joint Typhoon Warning Center (JTWC) Storm Wallets

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Joint Typhoon Warning Center (JTWC) is responsible for typhoon forecasts and warnings for the Western Pacific and Indian Ocean basins. After each storm, the...

  6. Nano-Engineered Structural Joints Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A versatile class of high-performance structural joints is proposed where massive interatomic bonds over the large surface areas of nanostructured surfaces...

  7. Joint-venture Insurance Firm Born

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    @@ Generali China Life insurance Company Ltd.began operations in February this year in Guangzhou,capital of South China's Guangdong Province - the first joint-venture insurer since China joined the World Trade Organization.

  8. Bones, Muscles, and Joints: The Musculoskeletal System

    Science.gov (United States)

    ... Story" 5 Things to Know About Zika & Pregnancy Bones, Muscles, and Joints KidsHealth > For Parents > Bones, Muscles, ... able to stand, walk, run, or even sit. Bones and What They Do From our head to ...

  9. Joint action without and beyond planning

    DEFF Research Database (Denmark)

    Blomberg, Olle

    2013-01-01

    Leading philosophical accounts of joint activity, such as Michael Bratman’s account of ‘shared intentional activity’, take joint activity to be the outcome of two or more agents having a ‘shared intention’, where this is a certain pattern of mutually known prior intentions (plans) that are directed...... toward a common goal. With Bratman’s account as a foil, I address two lacunas that are relatively unexplored in the philosophical literature. The first lacuna concerns how to make sense of the apparently joint cooperative activities of agents that lack the capacities for planning and “mindreading” that...... “online”—that is, during action execution as a joint activity unfolds—without recourse to plans that specify in advance what they should do (consider the coordination involved when two friends meet and do a “high five”). Chapters 2 and 3 focus on the first lacuna, while chapters 4 and 5 focus on the...

  10. Migratory Bird Joint Ventures of New Mexico

    Data.gov (United States)

    Earth Data Analysis Center, University of New Mexico — A joint venture is a self-directed partnership of agencies, organizations, corporations, tribes, or individuals that has formally accepted the responsibility of...

  11. Candida infection of a prosthetic shoulder joint

    International Nuclear Information System (INIS)

    A heroin addict developed a Candida parapsilosis infection in a prosthetic shoulder joint. Radiographs showed loose fragments of cement with prosthetic loosening. The patient was treated with removal of the prosthesis and intravenous amphotericin B followed by oral ketoconazole. (orig.)

  12. Control of compliant anthropomimetic robot joint

    Directory of Open Access Journals (Sweden)

    Svetozarević Bratislav

    2011-01-01

    Full Text Available In this paper we propose a control strategy for a robot joint which fully mimics the typical human joint structure. The joint drive is based on two actuators (dc motors, agonist and antagonist, acting through compliant tendons and forming a nonlinear multi-input multi-output (MIMO system. At any time, we consider one actuator, the puller, as being responsible for motion control, while the role of the other is to keep its tendon force at some appropriate low level. This human-like and energetically efficient approach requires the control of 'switching', or exchanging roles between actuators. Moreover, an algorithm based on adaptive force reference is used to solve a problem of slacken tendons during the switching and to increase the energy efficiency. This approach was developed and evaluated on increasingly complex robot joint configurations, starting with simple and noncompliant system, and finishing with nonlinear and compliant system.

  13. Arthritis Mechanisms May Vary by Joint

    Science.gov (United States)

    ... Kids Become Lifelong Learners Featured Website: GeneEd: Genetics, Education, Discovery Links Rheumatoid Arthritis Osteoarthritis Gout Rheumatoid Arthritis Juvenile Arthritis Feeling Out of Joint: The Aches of Arthritis CONTACT ...

  14. Joint Commission issues staff behavior standard.

    Science.gov (United States)

    2008-09-01

    * Medical literature provides evidence that inappropriate behaviors can cause adverse outcomes. * The Joint Commission wants code of conduct, with consequences for bad behaviors. * Quality managers should emphasize a pattern of behavior rather than an isolated incident. PMID:18727307

  15. DOE and NASA joint Dark Energy mission

    CERN Multimedia

    2003-01-01

    "DOE and NASA announced their plan for a Joint Dark Energy Mission (JDEM) on October 23, 2003, at the NASA Office of Space Science Structure and Evolution of the Universe Subcommittee (SEUS) meeting" (1 paragraph).

  16. Joint Training of Deep Boltzmann Machines

    OpenAIRE

    Goodfellow, Ian; Courville, Aaron; Bengio, Yoshua

    2012-01-01

    We introduce a new method for training deep Boltzmann machines jointly. Prior methods require an initial learning pass that trains the deep Boltzmann machine greedily, one layer at a time, or do not perform well on classifi- cation tasks.

  17. North American Joint Ventures 2014 revision

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — A joint venture is a self-directed partnership of agencies, organizations, corporations, tribes, or individuals that has formally accepted the responsibility of...

  18. A Joint-Constraint Model for Human Joints using Signed Distance-Fields

    DEFF Research Database (Denmark)

    Engell-Nørregård, Morten Pol; Niebe, Sarah Maria; Erleben, Kenny

    2012-01-01

    We present a local joint-constraint model for a single joint which is based on distance fields. Our model is fast, general, and well suited for modeling human joints. In this work, we take a geometric approach and model the geometry of the boundary of the feasible region, i.e., the boundary of all...... allowed poses. A region of feasible poses can be built by embedding motion captured data points in a signed distance field. The only assumption is that the feasible poses form a single connected set of angular values. We show how signed distance fields can be used to generate fast and general joint......-constraint models for kinematic figures. Our model is compared to existing joint-constraint models, both in terms of generality and computational cost. The presented method supports joint-constraints of up to three degrees of freedom and works well with sampled motion data. Our model can be extended to handle inter...

  19. Torque Sensors for Robot Joint Control

    OpenAIRE

    Tsetserukou, Dzmitry; Tachi, Susumu

    2008-01-01

    In Chapter, the stages of the joint torque sensor design are presented. New torque sensors for implementation of virtual backdrivability of robot joint transmissions have been developed. Torque measurement techniques, namely, electrical, electromagnetic, and optical, are discussed in detail. Technical requirements aimed at designing the highperformance torque sensor for humanoid robot arm were formulated. The substantial advantages of the optical technique motivated our choice in its favor. T...

  20. Predisposition for temporomandibular joint disorders: loose ligaments.

    Science.gov (United States)

    Deodato, Francesco; Trusendi, Raffaello; Giorgetti, Roberto; Scalese, Marco U

    2006-07-01

    Loose ligaments are often a predisposing factor of temporomandibular joint (TMJ) disorders. This causal factor was analyzed in 701 subjects presenting at the TMJ and Posture Center of Siena University with TMJ pain or dysfunction. Along with the conventional jaw examination, a Carter and Wilkinson test as modified by Beighton was also done. We found a correlation among the parameters of age, gender, TMJ disorder, joint pain, muscle pain, and loose ligaments. PMID:16933458

  1. Joint IGORR 2013 and IAEA Technology Meeting

    International Nuclear Information System (INIS)

    This Joint Meeting contains articles of Joint IGORR 2013 and IAEA Technology Meeting. It was held on Oct 13-18, 2013 in Daejeon, Korea. The main topics are as follows: Opening session, Ageing, International topics, Safety of research reactor, Irradiation technology, Utilization of research reactors, New research reactor project, Fuel, Secondary source, Innovative methods, NDT and RI, Operation and maintenance and so on. (Yi, J. H.)

  2. Interventional radiology in bone and joint

    Energy Technology Data Exchange (ETDEWEB)

    Bard, M.; Laredo, J.D.

    1988-01-01

    Recent radiologic procedures in bone and joints, some of which eliminate the need for surgery are exposed, including: trephine biopsies of the thoracic and lumbar spine, sacro-iliac joints, peripheral bones synovial membrane and soft tissues, using either fluoroscopic echographic or CT guidance - chemonucleolysis - vascular embolization of skeletal tumors and management of vertebral hemangiomas - selective steroid injection in a broad spectrum of diseases including vertebral facet syndrome, cervicobrachial nerve root pain, rotator cuff calcium deposit, bone cysts.

  3. Septic arthritis of a lumbar facet joint

    International Nuclear Information System (INIS)

    Septic arthritis of the posterior lumbar joints is extremely rare. The clinical picture of the unusual site of infection can easily lead to confusion with spondylo-discitis which is more common. We report a case of a 50-year-old women with Staphylococcus aureus septic arthritis of the left L5-S1 lumbar facet joint. CT scan was helpful to establish the diagnosis and to guide the percutaneous needle biopsy. (authors)

  4. Monarticular involvement of the manubriosternal joint

    Energy Technology Data Exchange (ETDEWEB)

    Jurik, A.G.; Graudal, H.; Carvalho, A. de

    1985-07-01

    Four females and two males with seronegative monoarthritis of the manubriosternal joint are reported. Two patients had pustulosis palmoplantaris, one psoriasis vulgaris, and one HLA-B27. The arthritis is considered to be a monarticular manifestation of seronegative spondylarthritis. Two patients had no other diseases or signs. Four patients were followed for a mean of 8.5 years (range 2-16 years) during which time affection of other joints or the spine was not seen.

  5. Wormhole Formation in RSRM Nozzle Joint Backfill

    Science.gov (United States)

    Stevens, J.

    2000-01-01

    The RSRM nozzle uses a barrier of RTV rubber upstream of the nozzle O-ring seals. Post flight inspection of the RSRM nozzle continues to reveal occurrence of "wormholes" into the RTV backfill. The term "wormholes", sometimes called "gas paths", indicates a gas flow path not caused by pre-existing voids, but by a little-understood internal failure mode of the material during motor operation. Fundamental understanding of the mechanics of the RSRM nozzle joints during motor operation, nonlinear viscoelastic characterization of the RTV backfill material, identification of the conditions that predispose the RTV to form wormholes, and screening of candidate replacement materials is being pursued by a joint effort between Thiokol Propulsion, NASA, and the Army Propulsion & Structures Directorate at Redstone Arsenal. The performance of the RTV backfill in the joint is controlled by the joint environment. Joint movement, which applies a tension and shear load on the material, coupled with the introduction of high pressure gas in combination create an environment that exceeds the capability of the material to withstand the wormhole effect. Little data exists to evaluate why the material fails under the modeled joint conditions, so an effort to characterize and evaluate the material under these conditions was undertaken. Viscoelastic property data from characterization testing will anchor structural analysis models. Data over a range of temperatures, environmental pressures, and strain rates was used to develop a nonlinear viscoelastic model to predict material performance, develop criteria for replacement materials, and quantify material properties influencing wormhole growth. Three joint simulation analogs were developed to analyze and validate joint thermal barrier (backfill) material performance. Two exploratory tests focus on detection of wormhole failure under specific motor operating conditions. A "validation" test system provides data to "validate" computer models and

  6. ELECTRICAL JOINTS FOR THE EUROPEAN LCT COIL

    OpenAIRE

    Albrecht, C.; Marsing, H.; Neumüller, H.

    1984-01-01

    A description is given of a solder-press joint of segmented design for. Tesla, as well as of inductive measuring apparatus. One 4-segment unit in length and exhibits an electrical resistance of 2.3 . 10-10 Ω at 1 T. Resistance of a prototype joint was measured up to 5 T. Thermal cycles between 77 K and 300 K did not affect the resistance. Reproducibility of fabrication has been proved.

  7. Optimal Ownership Structures in Asymmetric Joint Ventures

    OpenAIRE

    Paul Belleflamme; Francis Bloch

    2000-01-01

    This paper investigates the relation between asymmetries in the distribution of shares in joint ventures and asymmetries between the parent companies. When the joint venture and the parent companies are controlled by separate entities, we provide a simple formula to compute the optimal ownership structure. This formula is applied to various models of market interaction, showing that larger companies should have a larger fraction of shares, and so should companies whose goods are closer substi...

  8. Attention, Joint Attention, and Social Cognition

    OpenAIRE

    Mundy, Peter; Newell, Lisa

    2007-01-01

    Before social cognition there is joint processing of information about the attention of self and others. This joint attention requires the integrated activation of a distributed cortical network involving the anterior and posterior attention systems. In infancy, practice with the integrated activation of this distributed attention network is a major contributor to the development of social cognition. Thus, the functional neuroanatomies of social cognition and the anterior–posterior attention ...

  9. Joint hypermobility: incidence and some clinical symptoms

    OpenAIRE

    M P Isaev

    2003-01-01

    Objective. To study joint mobility range among urban population aged 18 to 30 years and to assess association of joint and other connective tissue structures disorders clinical signs with hypermobility. Material and methods. 769 randomly selected individuals aged 18 to 30 (mean - 25,56) years (419 female and 350 male) were examined. Hypermobility was assessed with 9-point Beighton scale. Examination included skin stretchability evaluation at elbow back surface, determination of flat feet, hig...

  10. Bundling and joint marketing by rival firms

    OpenAIRE

    Jeitschko, Thomas D.; Jung, Yeonjei; Kim, Jaesoo

    2014-01-01

    We study joint marketing arrangements by competing firms who engage in price discrimination between consumers who patronize only one firm (single purchasing) and those who purchase from both competitors (bundle purchasers). Two types of joint marketing are considered. Firms either commit to a component-price that applies to bundle-purchasers and then firms set stand-alone prices for single purchasers; or firms commit to a rebate off their stand alone price that will be applied to bundle-purch...

  11. Osteoligamentous injuries of the medial ankle joint

    OpenAIRE

    Lötscher, P.; Lang, T. H.; Zwicky, L.; Hintermann, B; Knupp, M

    2015-01-01

    Injuries of the ankle joint have a high incidence in daily life and sports, thus, playing an important socioeconomic role. Therefore, proper diagnosis and adequate treatment are mandatory. While most of the ligament injuries around the ankle joint are treated conservatively, great controversy exists on how to treat deltoid ligament injuries in ankle fractures. Missed injuries and inadequate treatment of the medial ankle lead to inferior outcome with instability, progressive deformity, and ank...

  12. Monarticular involvement of the manubriosternal joint

    International Nuclear Information System (INIS)

    Four females and two males with seronegative monoarthritis of the manubriosternal joint are reported. Two patients had pustulosis palmoplantaris, one psoriasis vulgaris, and one HLA-B27. The arthritis is considered to be a monarticular manifestation of seronegative spondylarthritis. Two patients had no other diseases or signs. Four patients were followed for a mean of 8.5 years (range 2-16 years) during which time affection of other joints or the spine was not seen. (orig.)

  13. Kinematics of Hooke universal joint robot wrists

    Science.gov (United States)

    Mckinney, William S., Jr.

    1988-01-01

    The singularity problem associated with wrist mechanisms commonly found on industrial manipulators can be alleviated by redesigning the wrist so that it functions as a three-axis gimbal system. This paper discussess the kinematics of gimbal robot wrists made of one and two Hooke universal joints. Derivations of the resolved rate motion control equations for the single and double Hooke universal joint wrists are presented using the three-axis gimbal system as a theoretical wrist model.

  14. The synovial joint: a perfect tribological system

    OpenAIRE

    Noble, Prisca; Collin, Bernard; Lecomte-Beckers, Jacqueline; Magnée, Adrien; Denoix, Jean-Marie; Serteyn, Didier

    2010-01-01

    The synovial joint, by load bearing and by minimal wear and minimal friction conferring, is considered as a perfect tribological system. During these last years, researchs in articular biomechanics have been performed to study how the joint friction coefficient, a dimensionless measure which represents the ratio between the frictional force on the normal force, was close to zero. Today, there is still no consensual explanation and the articular prosthesis partially imitates the biological me...

  15. Expression of CGRP in the temporomandibular joint

    International Nuclear Information System (INIS)

    The presence and content of calcitonin gene-related peptide (CGRP) is evaluated in the hyperplastic retrodiscal tissue of the temporomandibular joint in patients with joint degenerative disease by radioimmunoassay. Study population has included 8 female patients in pre-menopausic status, without to be pregnant, without to be lactating for a year and with diagnostic of joint degenerative disease (osteoarthrosis). Pain levels are registered with visual analog scale, where 0 is absence of pain and 16 acute pain. A bone degeneration is classified as mild, moderate and severe, according to findings of nuclear magnetic resonance. The 15 retrodiscal hyperplastic tissue samples are taken from patients undergoing to open surgery of temporomandibular joint. The specimens were placed in plastic blocks with freezing medium and are stored at -70 degrees celsius until neuropeptide extraction by radioimmunoassay with kit for CGRP. A directly proportional relationship is established between the degree of bone degeneration and neuropeptide expression and between the osteoarthrosis classification with analogue visual scale. Findings have shown definitive correlation between pain levels and expression of neuropeptide. CGRP is expressed in the retrodiscal tissue of temporomandibular joint in human with joint degenerative disease and is directly related with levels osteoarthrosis and pain

  16. Joint attention, shared goals, and social bonding.

    Science.gov (United States)

    Wolf, Wouter; Launay, Jacques; Dunbar, Robin I M

    2016-05-01

    There has recently been interest in the ways in which coordinated movements encourage coactors to feel socially closer to one another, but this has generally overlooked the importance of necessary precursors to this joint action. Here we target two low-level behaviours involved in social coordination that may mediate a relationship between joint actions and social bonding, namely joint attention and shared goals. Participants engaged in a simple reaction time task while sitting next to a partner performing the same task. In a joint attention condition, both participants attended to stimuli presented on the same half of a computer screen, while in a control condition, they attended to opposite sides of the computer screen. Shared goals were manipulated by giving participants the instruction to keep below a threshold score for both individual response times and accuracy (individual goal), or their joint mean response time and accuracy (i.e., averaging their mean response time and accuracy with that of their partner: shared goal). Attending to the same side of the screen led to higher ratings on a composite social bonding index directed towards a partner, while shared goals did not cause any effects on partner ratings. Joint attention was sufficient to encourage social closeness with an interaction partner, which suggests that any activities which encourage attending to the same point in space could have some influence on how connected coactors feel about one another. PMID:26256821

  17. Joint hypermobility syndrome and related pain

    Directory of Open Access Journals (Sweden)

    Nilay Sahin

    2016-06-01

    Full Text Available Hypermobility is defined as an abnormally increased range of motion of a joint resulting from the excessive laxity of the soft tissues. This paper is focused on this commonly forgotten cause of several morbidities. The etiology of hypermobility is not very well known. One decade ago, joint hypermobility syndrome was considered as a benign condition, but now it is recognized as a significant contributor to chronic musculoskeletal pain, besides impacting on other organs. Patients with joint hypermobility syndrome often have diffuse, chronic complaints that are inconsistent with the musculoskeletal system. Chronic pain may cause loss of proprioception and so increased sensitivity to microtrauma, premature osteoarthritis de- velopment, soft tissue problems, psychosocial disorders, and neurophysiological deficiencies. Osteoarthritis, pes planus, mechanical low back pain, and soft tissue rheumatisms are frequent musculoskeletal findings as well as subluxations, thoracic outlet syndrome, rectal and uterine prolapses, hernias, and stress incontinence. Joint hypermobility syndrome's treatment is not easy, and nonsteroidal anti-inflammatory drugs are not usually effective or adequate. Proprioceptive and strengthening exercises have been reported to have supportive and therapeutic effects, but we have limited data on this issue. Joint hypermobility syndrome must be accepted as a multisystem connective tissue disorder rather than just joint laxities. As a result; clinicians must be aware of complexities of connective tissue disorders and comorbidities. [Arch Clin Exp Surg 2016; 5(2.000: 105-112

  18. Experimental joint immobilization in guinea pigs. Effects on the knee joint

    Science.gov (United States)

    Marcondesdesouza, J. P.; Machado, F. F.; Sesso, A.; Valeri, V.

    1980-01-01

    In young and adult guinea pigs, the aftermath experimentally induced by the immobilization of the knee joint in hyperextended forced position was studied. Joint immobilization which varied from one to nine weeks was attained by plaster. Eighty knee joints were examined macro and microscopically. Findings included: (1) muscular hypotrophy and joint stiffness in all animals, directly proportional to the length of immobilization; (2) haemoarthrosis in the first week; (3) intra-articular fibrous tissue proliferation ending up with fibrous ankylosis; (4) hyaline articular cartilage erosions; (5) various degrees of destructive menisci changes. A tentative explanation of the fibrous tissue proliferation and of the cartilage changes is offered.

  19. Effect of joint design on ballistic performance of quenched and tempered steel welded joints

    International Nuclear Information System (INIS)

    Highlights: • Traditional usage of austenitic stainless steel filler for armour steel welding shows poor ballistic performance. • Earlier efforts show dubious success on ballistic resistance of armour steel joints. • Comparative evaluation of equal/unequal joint design on ballistic performance. • Effect of joint design covers the main aspects of successful bullet stoppage. - Abstract: A study was carried out to evaluate the effect of joint design on ballistic performance of armour grade quenched and tempered steel welded joints. Equal double Vee and unequal double Vee joint configuration were considered in this study. Targets were fabricated using 4 mm thick tungsten carbide hardfaced middle layer; above and below which austenitic stainless steel layers were deposited on both sides of the hardfaced interlayer in both joint configurations. Shielded metal arc welding process was used to deposit for all layers. The fabricated targets were evaluated for its ballistic performance and the results were compared in terms of depth of penetration on weld metal. From the ballistic test results, it was observed that both the targets successfully stopped the bullet penetration at weld center line. Of the two targets, the target made with unequal double Vee joint configuration offered maximum resistance to the bullet penetration at weld metal location without any bulge at the rear side. The higher volume of austenitic stainless steel front layer and the presence of hardfaced interlayer after some depth of soft austenitic stainless steel front layer is the primary reason for the superior ballistic performance of this joint

  20. TSTA compound cryopump

    International Nuclear Information System (INIS)

    The Tritium System Test Assembly (TSTA), at the Los Alamos Scientific Laboratory, is intended to demonstrate realistic fuel supply and cleanup scenarios for future fusion reactors. The vacuum pumps must be capable of handling large quantities of reactor exhaust gases consisting largely of mixtures of hydrogen and helium isotopes. Cryocondensing pumps will not pump helium at 4.2 K; while cryosorption pumps using molecular sieves or charcoal have good helium pumping speed, the adsorbent clogs with condensed hydrogen while pumping mixtures of both. A solution to this problem is a compound design whereby the first stage condenses the hydrogen and the second, or sorption, stage pumps the helium. The TSTA pump designed at Lawrence Livermore National Laboratory uses argon gas to cryotrap the helium in the helium-hydrogen mixture. The argon is sprayed directly onto the 4.2 K surface at a rate proportional to the helium flow rate, permitting continuous pumping of the helium-hydrogen mixtures in a single-stage pump. However, the possibility of differential desorption as a first stage in the TSTA gas separation cycle required the inclusion of a first-stage hydrogen isotope condenser. The design, performance, and operating characteristics are discussed

  1. Compounding in synthetic aperture imaging.

    Science.gov (United States)

    Hansen, Jens Munk; Jensen, Jørgen Arendt

    2012-09-01

    A method for obtaining compound images using synthetic aperture data is investigated using a convex array transducer. The new approach allows spatial compounding to be performed for any number of angles without reducing the frame rate or temporal resolution. This important feature is an intrinsic property of how the compound images are constructed using synthetic aperture data and an improvement compared with how spatial compounding is obtained using conventional methods. The synthetic aperture compound images are created by exploiting the linearity of delay-and-sum beamformation for data collected from multiple spherical emissions to synthesize multiple transmit and receive apertures, corresponding to imaging the tissue from multiple directions. The many images are added incoherently, to produce a single compound image. Using a 192-element, 3.5-MHz, λ-pitch transducer, it is demonstrated from tissue-phantom measurements that the speckle is reduced and the contrast resolution improved when applying synthetic aperture compound imaging. At a depth of 4 cm, the size of the synthesized apertures is optimized for lesion detection based on the speckle information density. This is a performance measure for tissue contrast resolution which quantifies the tradeoff between resolution loss and speckle reduction. The speckle information density is improved by 25% when comparing synthetic aperture compounding to a similar setup for compounding using dynamic receive focusing. The cystic resolution and clutter levels are measured using a wire phantom setup and compared with conventional application of the array, as well as to synthetic aperture imaging without compounding. If the full aperture is used for synthetic aperture compounding, the cystic resolution is improved by 41% compared with conventional imaging, and is at least as good as what can be obtained using synthetic aperture imaging without compounding. PMID:23007781

  2. Organic Compounds in Carbonaceous Meteorites

    Science.gov (United States)

    Cooper, Grorge

    2001-01-01

    Carbonaceous meteorites are relatively enriched in soluble organic compounds. To date, these compounds provide the only record available to study a range of organic chemical processes in the early Solar System chemistry. The Murchison meteorite is the best-characterized carbonaceous meteorite with respect to organic chemistry. The study of its organic compounds has related principally to aqueous meteorite parent body chemistry and compounds of potential importance for the origin of life. Among the classes of organic compounds found in Murchison are amino acids, amides, carboxylic acids, hydroxy acids, sulfonic acids, phosphonic acids, purines and pyrimidines (Table 1). Compounds such as these were quite likely delivered to the early Earth in asteroids and comets. Until now, polyhydroxylated compounds (polyols), including sugars (polyhydroxy aldehydes or ketones), sugar alcohols, sugar acids, etc., had not been identified in Murchison. Ribose and deoxyribose, five-carbon sugars, are central to the role of contemporary nucleic acids, DNA and RNA. Glycerol, a three-carbon sugar alcohol, is a constituent of all known biological membranes. Due to the relative lability of sugars, some researchers have questioned the lifetime of sugars under the presumed conditions on the early Earth and postulated other (more stable) compounds as constituents of the first replicating molecules. The identification of potential sources and/or formation mechanisms of pre-biotic polyols would add to the understanding of what organic compounds were available, and for what length of time, on the ancient Earth.

  3. 29 CFR 825.106 - Joint employer coverage.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 3 2010-07-01 2010-07-01 false Joint employer coverage. 825.106 Section 825.106 Labor... AND MEDICAL LEAVE ACT OF 1993 Coverage Under the Family and Medical Leave Act § 825.106 Joint employer... employee, the businesses may be joint employers under FMLA. Joint employers may be separate and...

  4. 15 CFR 296.8 - Joint venture agreement.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Joint venture agreement. 296.8 Section... PROGRAM General § 296.8 Joint venture agreement. NIST shall not issue a TIP award to a joint venture and no costs shall be incurred under a TIP project by the joint venture members until such time as...

  5. Evaluation of temporomandibular joint positions in different malocclusions

    OpenAIRE

    Görücü Coşkuner, Hande; Kocadereli, İlken

    2013-01-01

    Temporomandibular joint is a secondary joint that connects mandible to temporal bone. Conventional radiographic imaging such as panoramic or transcranial radiographs, conventional tomography, magnetic resonance imaging, ultrasonography, artrography or cone beam computed tomography can be used for the evaluation of the temporomandibular joint. Although several studies have been done, relationship between the temporomandibular joint shape and position and occlusion could not be defined clearly,...

  6. Children with generalised joint hypermobility and musculoskeletal complaints

    DEFF Research Database (Denmark)

    Scheper, M C; Engelbert, R H H; Rameckers, E A A;

    2013-01-01

    To provide a state of the art on diagnostics, clinical characteristics, and treatment of paediatric generalised joint hypermobility (GJH) and joint hypermobility syndrome (JHS).......To provide a state of the art on diagnostics, clinical characteristics, and treatment of paediatric generalised joint hypermobility (GJH) and joint hypermobility syndrome (JHS)....

  7. Brazing technology of Ti alloy/stainless steel dissimilar metal joint at system integrated modular advanced reactor

    International Nuclear Information System (INIS)

    For the technoldogy development of brazing Ti alloy to stainless steel joints used at SMART, the status of brazing technology development, brazing processes, and the brazing technology of Ti alloy and stainless steel are reviewed. Because fusion welding process cannot be applied due to the formation of intermetallic compounds in the weld metal, brazing joint was selected at the design. The joint part is assembled with a thread composed with male part of Ti alloy tube and female part of stainless tube. The gap in the thread will be filled with brazing filler metal. However, brittle Ti-Fe intermetallic compounds are formed at the surface of stainless steel through the diffusion of Ti at the melt. Brazing conditions should be set-up to reduce the formation of intermetallic compounds. For that, 3 kinds of Ag filler metals were selected as the candidates and heating will be done with induction and electric furnaces. Through measuring of joint strength according to the control of pre- and post-braze treatment, heating rate and heating time, optimal brazing method will be fixed. To qualify the brazing procedure and performance and to check defects in final product, the inspection plan will be established according to the req2wuirements of AWS and ASME

  8. Influence of laser energy input mode on joint interface characteristics in laser brazing with Cu-base filler metal

    Institute of Scientific and Technical Information of China (English)

    LI Li-qun; FENG Xiao-song; CHEN Yan-bin

    2008-01-01

    The flange butt joints of 1 mm-thick galvanized steel sheets were brazed with CuSi3 as filler metal at different laser heating modes. The microstructures and element distributions of joint interface were investigated by SEM and EDS. The results show that there is no obvious interface layer with the circular individual beam heating and lamellar Fe-Si intermetallic compound layer is found with dual-beam laser spot heating. With the irradiation of rectangular laser spot, the joint interface layer is also formed. The layer thickness is larger than that of dual-beam brazing and the layer shape is fiat so that intermetallic compounds trend to grow into cellular crystals. Moreover, the interface layer shape also depends on its position in the joint. Under the high heat input, dendritic or granular intermetallic compounds dispersively distribute in brazing seam adjacent to the interface, which is caused by the melting or dissolving of the base metal. According to the results, the brazing quality can be controlled by laser heating mode and processing parameters.

  9. Shear fracture of jointed steel plates of bolted joints under impact load

    Science.gov (United States)

    Daimaruya, M.; Fujiki, H.; Ambarita, H.; Kobayashi, H.; Shin, H.-S.

    2013-07-01

    The present study is concerned with the development of a fracture criterion for the impact fracture of jointed steel plates of bolted joints used in a car body, which contributes to crash simulations by CAE. We focus our attention on the shear fracture of the jointed steel plates of lap-bolted joints in the suspension of a car under impact load. Members of lap-bolted joints are modelled as a pair of steel plates connected by a bolt. One of the plates is a specimen subjected to plastic deformation and fracture and the other is a jig subjected to elastic deformation only. Three kinds of steel plate specimens are examined, i.e., a common steel plate with a tensile strength of 270 MPa and high tensile strength steel plates of 440 and 590 MPa used for cars. The impact shear test was performed using the split Hopkinson bar technique for tension impact, together with the static test using a universal testing machine INSTRON 5586. The behaviour of the shear stress and deformation up to rupture taking place in the joint was discussed. The obtained results suggest that a stress-based fracture criterion may be developed for the impact fracture of jointed steel plates of a lap-bolted joint.

  10. The association between generalized joint hypermobility and temporomandibular joint disorders : A systematic review

    NARCIS (Netherlands)

    Dijkstra, PU; Kropmans, TJB; Stegenga, B

    2002-01-01

    To analyze conflicting evidence in the literature for the association between temporomandibular joint disorders (TMD) and generalized joint hypermobility (GJH), we performed a bibliographic search. The methodological quality of the 14 papers found was assessed according to 14 criteria. Papers were i

  11. Shear fracture of jointed steel plates of bolted joints under impact load

    International Nuclear Information System (INIS)

    The present study is concerned with the development of a fracture criterion for the impact fracture of jointed steel plates of bolted joints used in a car body, which contributes to crash simulations by CAE. We focus our attention on the shear fracture of the jointed steel plates of lap-bolted joints in the suspension of a car under impact load. Members of lap-bolted joints are modelled as a pair of steel plates connected by a bolt. One of the plates is a specimen subjected to plastic deformation and fracture and the other is a jig subjected to elastic deformation only. Three kinds of steel plate specimens are examined, i.e., a common steel plate with a tensile strength of 270 MPa and high tensile strength steel plates of 440 and 590 MPa used for cars. The impact shear test was performed using the split Hopkinson bar technique for tension impact, together with the static test using a universal testing machine INSTRON 5586. The behaviour of the shear stress and deformation up to rupture taking place in the joint was discussed. The obtained results suggest that a stress-based fracture criterion may be developed for the impact fracture of jointed steel plates of a lap-bolted joint

  12. Micromechanics approach to poroelastic behavior of a jointed rock

    OpenAIRE

    Maghous, Samir; Dormieux, Luc; Kondo, Djimédo; SHAO, Jian Fu

    2013-01-01

    The formulation of macroscopic poroelastic behavior of a jointed rock is investigated within the framework of a micro-macro approach. The joints are modeled as interfaces, and their behavior is modeled by means of generalized poroelastic state equations. Starting from Hill's lemma extended for a jointed medium and extending the concept of strain concentration to relate the joint displacement jump to macroscopic strain, the overall poroelastic constitutive equations for the jointed rock are fo...

  13. Improved Automatically Locking/Unlocking Orthotic Knee Joint

    Science.gov (United States)

    Weddendorf, Bruce

    1995-01-01

    Proposed orthotic knee joint improved version of one described in "Automatically Locking/Unlocking Orthotic Knee Joint" (MFS-28633). Locks automatically upon initial application of radial force (wearer's weight) and unlocks automatically, but only when all loads (radial force and bending) relieved. Joints lock whenever wearer applies weight to knee at any joint angle between full extension and 45 degree bend. Both devices offer increased safety and convenience relative to conventional orthotic knee joints.

  14. Joint hypermobility in adults referred to rheumatology clinics.

    OpenAIRE

    Bridges, A J; Smith, E.; Reid, J.

    1992-01-01

    Joint hypermobility is a rarely recognised aetiology for focal or diffuse musculoskeletal symptoms. To assess the occurrence and importance of joint hypermobility in adult patients referred to a rheumatologist, we prospectively evaluated 130 consecutive new patients for joint hypermobility. Twenty women (15%) had joint hypermobility at three or more locations (greater than or equal to 5 points on a 9 point scale). Most patients with joint hypermobility had common musculoskeletal problems as t...

  15. The anxiety between individuals with and without joint hypermobility

    OpenAIRE

    Gulcan Gurer; Faruk Sendur; Bulent Kadri Gultekin; Mehmet Erkan Ozcan

    2010-01-01

    Background and Objectives: This study was performed to compare the anxiety disorders between individuals with and without joint hypermobility. Methods: A total of 94 Turkish volunteers, 40 subjects (38 females, 2 males) with joint hypermobility and 54 controls (47 females, 7 males) without joint hypermobility, were included in this study. We evaluated the joint hypermobility by using the Beighton scoring system in the participants and a Beighton score of at least 4 was considered as joint hyp...

  16. Characterization of adhesively bonded joints using bulk adhesive properties

    OpenAIRE

    Kon, Haruhiko

    1991-01-01

    Though using bulk adhesive properties to predict adhesively bonded joint response has yet to be proven infallible, based upon the success of previous works, this effort attempts to shed some light on the stresses present in a typical automotive bonded joint. Adhesive material properties obtained in previous works were used in a finite element analysis of a simulated automotive joint to predict the stresses in that joint. The automotive joint analyzed was a simplified repr...

  17. Handbook on dynamics of jointed structures.

    Energy Technology Data Exchange (ETDEWEB)

    Ames, Nicoli M.; Lauffer, James P.; Jew, Michael D.; Segalman, Daniel Joseph; Gregory, Danny Lynn; Starr, Michael James; Resor, Brian Ray

    2009-07-01

    The problem of understanding and modeling the complicated physics underlying the action and response of the interfaces in typical structures under dynamic loading conditions has occupied researchers for many decades. This handbook presents an integrated approach to the goal of dynamic modeling of typical jointed structures, beginning with a mathematical assessment of experimental or simulation data, development of constitutive models to account for load histories to deformation, establishment of kinematic models coupling to the continuum models, and application of finite element analysis leading to dynamic structural simulation. In addition, formulations are discussed to mitigate the very short simulation time steps that appear to be required in numerical simulation for problems such as this. This handbook satisfies the commitment to DOE that Sandia will develop the technical content and write a Joints Handbook. The content will include: (1) Methods for characterizing the nonlinear stiffness and energy dissipation for typical joints used in mechanical systems and components. (2) The methodology will include practical guidance on experiments, and reduced order models that can be used to characterize joint behavior. (3) Examples for typical bolted and screw joints will be provided.

  18. [Arthritis of the Medial Knee Joint Compartment].

    Science.gov (United States)

    Matziolis, G; Röhner, E

    2015-10-01

    23 % of all persons older than 65 years suffer from osteoarthritis of the medial compartment of the knee joint, a very common situation in orthopaedic practice 1. As a result of the demographic trend the number of patients is expected to increase in the future. Based on specific joint biomechanics and kinematics the medial knee joint compartment is more frequently affected than the lateral. Only an understanding of the functional anatomy and underlying pathology allows a critical evaluation of different available conservative and operative treatment options. This article gives an overview of diagnostic and therapeutic strategies of osteoarthritis of the medial knee joint. Frequently performed surgeries, e.g. high tibial osteotomy (HTO), unicompartmental knee arthroplasty (UKA) and total knee arthroplasty (TKA) will be presented in a comparative manner. The actual scientific evidence will be given with the goal of an evidence based therapy that is adopted to stage and pathology of osteoarthritis of the medial compartment of the knee joint. PMID:26451864

  19. Computed Tomography of the lumbar facet joints

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Mi Ryoung; Kim, Yung Soon; Lee, Joo Hyuk; Jeon, Hae Sang; Kim, Dae Yung [Kang Nam General Hospital, Seoul (Korea, Republic of)

    1989-08-15

    The lumbar facet disease is a frequently overlooked cause of sciatic pain, but the lumbar facet joints are well-recognized source of low back pain and radiating leg pain which can be confused with sciatica due to herniated disc. We measured the angulation of the facet joints on axial spine CT films in 149 cases which contains 41 normal group and 108 abnormal group and studied the relationship between the angulation and degeneration of the facets, the asymmetry of each sided facets and facet degeneration, the asymmetry and disc protrusion, and the asymmetry and annular bulging of the disc. The results were as follows: 1. Facet angulation in abnormal group were more sagittally oriented than the normal group. 2. The angulation of right facet was more sagittally oriented than the left in L4-5 level of abnormal group. 3. Degeneration of facet joints occur asymmetrically, and the more facet joint degenerates, the more it orients sagittally, particularly in L4-5. 4. Asymmetry in facet joint degeneration and unilateral disc protrusion of L5-SI level is greater than the normal gro0008.

  20. Tribological aspects of joint intraaricular therapy.

    Science.gov (United States)

    Cherniakova, Yu M; Pinchuk, L S

    2011-01-01

    The condition of synovial joints affected by synovitis or degeneration dystrophy has been usually normalized by drugs of antibacterial, anti-inflammatory, immunomodulating and/or lubricating-protective action injected into the joint cavity. These preparations influence, but in different way, the friction in joints and wear of cartilages, even if they belong to the same pharmacological group and follow the same medication mechanism. With the development of a large group of lubricating-and-protective substitutes for the synovial fluid the tribological efficiency of injection drugs has begun to attract attention, whereas no information is available in the literature on pharmacopoeia or orthopedics about the lubricity of anti-inflammatory and antibacterial drugs commonly used as injections. The mechanisms by which structure and properties of lubricating films containing drugs undergo transformation under the influence of biological field in joints remain in fact unknown. In vitro experiments have been conducted to simulate a biofield of a joint; the lubricity of some injection drugs used in orthopedics has been evaluated. PMID:21500764

  1. Guidelines for evaluating potential joint ventures.

    Science.gov (United States)

    Himmelsbach, W A

    1987-04-01

    Holy Cross Health System (HCHS), South Bend, IN, participates in 25 joint ventures; 9 of these involve partnerships with for-profit structures and 18 relate to activities with medical staffs. To ensure that such arrangements respect the sponsoring religious institute's requirements, HCHS follows a 16-point policy to guide the development of joint ventures. The policy requires joint ventures to: Have a specific purpose relevant to community health care needs; Strive to respond to need regardless of a person's race, creed, color, or ability to pay; Include in legal documents a statement of the intent to uphold Church teachings; Base their activities on an "arm's length" relationship; Undertake reasonable efforts to establish the entity as a not-for-profit, tax-exempt corporation; Confine operations to the subsidiary's service area unless collaboration with other Catholic-sponsored organizations is involved; Include a "dispute resolution" clause in organizational documents; Establish as the partner on adequately capitalized, wholly owned not-for-profit corporation to minimize liability exposure, if the HCHS is to be a general partner in the joint venture; Retain professional consultants approved by the corporate office; Maintain reserved powers for majority-owned or majority-controlled joint ventures that are ecclesiastical entities. PMID:10301633

  2. Septic arthritis in the temporomandibular joint

    Directory of Open Access Journals (Sweden)

    Hassan Mahdi Al-Khalisy

    2015-01-01

    Full Text Available Septic arthritis of the temporomandibular joint (TMJ is a rare event that has only been reported a few dozen times worldwide. This case is remarkable for septic arthritis of the TMJ joint in an otherwise healthy male. Case Report: A 24-year-old male presented to the emergency department with periauricular swelling, erythema, fever, myalgia′s and generalized joint pain. He had previously sought medical attention and was placed on ciprofloxacin. However, he developed facial swelling and a rash and had to discontinue the antibiotic. On physical exam the patient had a large swelling and tenderness in his left periauricular area, with erythema and deviation of the right mandible which limited his ability to open the mouth. A computed tomography showed mild asymmetric soft tissue swelling in the left pharyngeal region but did not show joint effusion. Subsequent magnetic resonance imaging did show effusion of the joint space. The effusion was drained, and the synovial fluid was submitted for gram stain, culture, and sensitivity. The cultures grew menthicillin sensitive Staphyloccocus Aureus. The patient was discharged to complete a two week course of intravenous (IV Ceftriaxone and IV Vancomycin via home infusion. Conclusion: Septic Arthritis of the TMJ is a rare event with very specific clinical symptoms. Due to the low sensitivity of the computed tomography scan, magnetic resonance imaging should be considered when computed tomography scan is negative for TMJ effusion.

  3. Tool geometry, rotation and travel speeds effects on the properties of dissimilar magnesium/aluminum friction stir welded lap joints

    International Nuclear Information System (INIS)

    Highlights: • Tool geometry, rotation and travel speeds show great effect on the microstructure stability of FSW joint. • Increasing rotation and travel speeds resulted in increasing the tensile strength and ductility of the joints. • Better intermixing between Al/Mg alloys was obtained by tapered threaded pin. • A mechanical interlocking mechanism proposed for higher ductility and superior tensile properties in FSW joints. - Abstract: Lap joint friction stir welding (FSW) between dissimilar AZ31B and Al 6061 alloys sheets was conducted using various welding parameters including tool geometry, rotation and travel speeds. Tapered threaded pin and tapered pin tools were applied to fabricate FSW joints, using different rotation and travel speeds. Metallurgical investigations including X-ray diffraction pattern (XRD), optical microscopy images (OM), scanning electron microscopy equipped with an energy-dispersive X-ray spectroscopy (SEM–EDS) and electron probe microanalysis (EPMA) were used to characterize joints microstructures made with different welding parameters. Intermetallic phases were detected in the weld zone (WZ). Various microstructures were observed in the stir zone which can be attributed to using different travel and rotation speeds. Mechanical evaluation including lap shear fracture load test and microhardness measurements indicated that by simultaneously increasing the tool rotation and travel speeds, the joint tensile strength and ductility reached a maximum value. Microhardness studies and extracted results from stress–strain curves indicated that mechanical properties were affected by FSW process. Furthermore, phase analyses by XRD indicated the presence of intermetallic compounds in the weld zone. Finally, in the Al/Mg dissimilar weld, fractography studies showed that intermetallic compounds formation in the weld zone had an influence on the failure mode

  4. Estimation of Joint types and Joint Limits from Motion capture data

    DEFF Research Database (Denmark)

    Engell-Nørregård, Morten Pol; Erleben, Kenny

    2009-01-01

    It is time-consuming for an animator to explicitly model joint types and joint limits of articulated figures. In this paper we describe a simple and fast approach to automated joint estimation from motion capture data of articulated figures. Our method will make the joint modeling more efficient...... and less time consuming for the animator by providing a good starting estimate that can be fine-tuned or extended by the animator if she wishes, without restricting her artistic freedom. Our method is simple, easy to implement and specific for the types of articulated figures used in interactive animation...... such as computer games. Other work for joint limit modeling consider more complex and general purpose models. However, these are not immediately suitable for inverse kinematics skeletons used in interactive applications....

  5. Effect of Lanthanum on Driving Force for Cu6Sn5 Growth and Improvement of Solder Joint Reliability

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    By means of adding low content of rare earth element La into Sn60-Pb40 solder alloy, the growth of Cu6Sn5 intermetallic compound at the interface of solder joint is hindered, and the thermal fatigue life of solder joint is increased by 2 times. The results of thermodynamic calculation based on diffusion kinetics show that, the driving force for Cu6Sn5 growth is lowered by adding small content of La in Sn60-Pb40 solder alloy. Meanwhile, there is an effective local mole fraction range of La, in which, 0.18% is the limited value and 0.08% is the best value.

  6. II-VI semiconductor compounds

    CERN Document Server

    1993-01-01

    For condensed matter physicists and electronic engineers, this volume deals with aspects of II-VI semiconductor compounds. Areas covered include devices and applications of II-VI compounds; Co-based II-IV semi-magnetic semiconductors; and electronic structure of strained II-VI superlattices.

  7. Cytotoxic Compounds from Zanthoxylum Americanum

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Four pyranocoumarins: dipetaline, alloxanthoxyletin, xanthoxyletin, and xanthyletin, and two lignans: sesamin and asarinin were isolated from the northern prickly ash, Zanthoxylum americanum. To varying degrees, all six compounds inhibited the incorporation of tritiated thymidine into human leukemia (HL-60) cells and the inhibitory effect was dependent on the structures of the isolated compounds.

  8. Properties and Reliability of Solder Microbump Joints Between Si Chips and a Flexible Substrate

    Science.gov (United States)

    Ko, Yong-Ho; Kim, Min-Su; Bang, Junghwan; Kim, Taek-Soo; Lee, Chang-Woo

    2015-07-01

    Future generations of electronics are expected to include flexible, bendable, and wearable devices. There have been very few studies, however, on the bonding technology and reliability of bonding joints between a chip and a flexible substrate. In this study, we investigated the properties and reliability of joints formed with Sn-58Bi solder microbumps between a Si chip and a flexible substrate. For fine-pitch bonding, we formed Cu pillar bumps and Sn-58Bi solder microbumps with diameter of 25 μm by electroplating. The Si chips were then bonded on a flexible substrate finished with electroless nickel immersion gold (ENIG) using flip-chip technology, processing at 170°C under a force of 1 N, 2 N, or 3 N for 15 s. Cross-sectional images of bump joints were analyzed using field-emission scanning electron microscopy. While the Cu6Sn5 intermetallic compound (IMC) was formed on the Cu-pillar-bump side, another IMC, Ni3Sn4, was formed on the ENIG-substrate side. In addition, we performed a shear test, thermal shock test, and bending test to evaluate the joints' mechanical properties and reliability. The bending test was performed by a machine designed for joints on flexible substrates. Unit shear force of 2 N was the nominally highest value obtained from joints prepared under the three bonding conditions. After the thermal shock test, we observed cracks initiated at the Cu6Sn5/Sn-58Bi interface, which then propagated within the solder bumps or at the interface. In the case of the bending test, failure occurred at the Ni3Sn4/Sn-58Bi interface or within the solder bumps.

  9. Bilayer Effects of Antimalarial Compounds.

    Directory of Open Access Journals (Sweden)

    Nicole B Ramsey

    Full Text Available Because of the perpetual development of resistance to current therapies for malaria, the Medicines for Malaria Venture developed the Malaria Box to facilitate the drug development process. We tested the 80 most potent compounds from the box for bilayer-mediated effects on membrane protein conformational changes (a measure of likely toxicity in a gramicidin-based stopped flow fluorescence assay. Among the Malaria Box compounds tested, four compounds altered membrane properties (p< 0.05; MMV007384 stood out as a potent bilayer-perturbing compound that is toxic in many cell-based assays, suggesting that testing for membrane perturbation could help identify toxic compounds. In any case, MMV007384 should be approached with caution, if at all.

  10. Optimizing Synthetic Aperture Compound Imaging

    DEFF Research Database (Denmark)

    Hansen, Jens Munk; Jensen, Jørgen Arendt

    2012-01-01

    Spatial compound images are constructed from synthetic aperture data acquired using a linear phased-array transducer. Compound images of wires, tissue, and cysts are created using a method, which allows both transmit and receive compounding without any loss in temporal resolution. Similarly to...... optimal for lesion detection. Synthetic aperture data are acquired from unfocused emissions and 154 compound images are constructed by synthesizing different aperture configurations with more or less compounding, all maintaining a constant resolution across depth corresponding to an f-number of 2.0 for...... transmit and receive. The same configurations are used for scanning a phantom with cysts, and it is demonstrated how an improved cysts contrast follows from an aperture configuration, which gives a higher value for the performance measure extracted from the phantom without cysts. A correlation value R = 0...

  11. Thermal Protection System with Staggered Joints

    Science.gov (United States)

    Simon, Xavier D. (Inventor); Robinson, Michael J. (Inventor); Andrews, Thomas L. (Inventor)

    2014-01-01

    The thermal protection system disclosed herein is suitable for use with a spacecraft such as a reentry module or vehicle, where the spacecraft has a convex surface to be protected. An embodiment of the thermal protection system includes a plurality of heat resistant panels, each having an outer surface configured for exposure to atmosphere, an inner surface opposite the outer surface and configured for attachment to the convex surface of the spacecraft, and a joint edge defined between the outer surface and the inner surface. The joint edges of adjacent ones of the heat resistant panels are configured to mate with each other to form staggered joints that run between the peak of the convex surface and the base section of the convex surface.

  12. Internal derangement of the temporomandibular joint

    International Nuclear Information System (INIS)

    Internal Derangement is one of the most common disorders of the Temporomandibular joint. It is defined as an abnormal anatomical relationship between the discus articularis and the other structures of the temporomandibular joint. More than 2/3 of patients with clinical symptoms of the temporomandibular joint have an internal derangement. The most frequent finding in internal derangement is an anterior dislocation of the disc with reduction after mouth opening. In more severe cases a complete anterior dislocation is found without reduction of the disc. Internal derangement is a risk factor for developing osteoarthritis with remodeling of the condylus and the fossa mandibularis. The most important modalities of radiologic diagnosis are arthrography, CT and MRI. The diagnosis of craniofacial dysfunction has been improved dramatically by modern imaging techniques, which have become essential tools for primary diagnostic and evaluation after conservative or surgical therapy. MRI has become the gold standard. (orig.)

  13. Joint shape segmentation with linear programming

    KAUST Repository

    Huang, Qixing

    2011-01-01

    We present an approach to segmenting shapes in a heterogenous shape database. Our approach segments the shapes jointly, utilizing features from multiple shapes to improve the segmentation of each. The approach is entirely unsupervised and is based on an integer quadratic programming formulation of the joint segmentation problem. The program optimizes over possible segmentations of individual shapes as well as over possible correspondences between segments from multiple shapes. The integer quadratic program is solved via a linear programming relaxation, using a block coordinate descent procedure that makes the optimization feasible for large databases. We evaluate the presented approach on the Princeton segmentation benchmark and show that joint shape segmentation significantly outperforms single-shape segmentation techniques. © 2011 ACM.

  14. Approach to Joint Pain in Children.

    Science.gov (United States)

    Balan, Suma

    2016-02-01

    It is not uncommon in pediatric clinical practice to encounter children with musculoskeletal symptoms. A number of disparate conditions can present with joint complaints in children. In this article, the author describes the clinical approach to a child presenting with joint complaints. A detailed clinical history, including the family history, along with a complete physical examination can provide vital clues to the underlying condition in most cases. A structured screening examination of the musculoskeletal system that has been recently developed (i.e., pGALS) is also discussed. It is also pointed out that the pattern of joint involvement gives us one of the most important clues to the etiology of arthritis. The pediatrician has to be aware of the conditions that can have arthritis as one of the manifestations so as to investigate and treat the child accordingly. PMID:26747081

  15. Computational Poromechanics of Human Knee Joint

    International Nuclear Information System (INIS)

    Extensive computer modeling has been performed in the recent decade to investigate the mechanical response of the healthy and repaired knee joints. Articular cartilages and menisci have been commonly modeled as single-phase elastic materials in the previous 3D simulations. A comprehensive study considering the interplay of the collagen fibers and fluid pressurization in the tissues in situ remains challenging. We have developed a 3D model of the human knee accounting for the mechanical function of collagen fibers and fluid flow in the cartilages and menisci. An anatomically accurate structure of the human knee was used for this purpose including bones, articular cartilages, menisci and ligaments. The fluid pressurization in the femoral cartilage and menisci under combined creep loading was investigated. Numerical results showed that fluid flow and pressure in the tissues played an important role in the mechanical response of the knee joint. The load transfer in the joint was clearly seen when the fluid pressure was considered.

  16. Computational Poromechanics of Human Knee Joint

    Science.gov (United States)

    Kazemi, Mojtaba; Li, LePing

    2012-02-01

    Extensive computer modeling has been performed in the recent decade to investigate the mechanical response of the healthy and repaired knee joints. Articular cartilages and menisci have been commonly modeled as single-phase elastic materials in the previous 3D simulations. A comprehensive study considering the interplay of the collagen fibers and fluid pressurization in the tissues in situ remains challenging. We have developed a 3D model of the human knee accounting for the mechanical function of collagen fibers and fluid flow in the cartilages and menisci. An anatomically accurate structure of the human knee was used for this purpose including bones, articular cartilages, menisci and ligaments. The fluid pressurization in the femoral cartilage and menisci under combined creep loading was investigated. Numerical results showed that fluid flow and pressure in the tissues played an important role in the mechanical response of the knee joint. The load transfer in the joint was clearly seen when the fluid pressure was considered.

  17. Experimental evaluation for joint estimation approach

    International Nuclear Information System (INIS)

    Single Photon Emission Computed Tomography (SPECT) provides a potential to perform in vivo quantification of the radioactivity and dose distributions in the process of evaluating radiopharmaceuticals. The inherent modest resolution in SPECT impedes the potential of accurate quantification. Previously, we investigated a joint estimation approach for combining SPECT functional information with high resolution, structurally correlated MRI anatomical information to improve the accuracy of SPECT quantification, and the computer simulation results showed that this approach can exploit MRI region information that matches the SPECT functional information and to reduce artifacts caused by mismatched MRI anatomical information. In this paper, we further describe the experimental evaluation of the joint estimation approach using actual SPECT and MRI imaging with an animal-sized phantom. We will describe practical details in applying the joint estimation approach and present the experimental evaluation results of quantitative analysis

  18. Joint disease in children of Asiatic origin

    International Nuclear Information System (INIS)

    Joint disorders in Asian children are varied due to the diversity of the Asian population and show some ethnic trends. The ethnic diversity, socio-economic and geographic factors in Asia have limited the availability of data from some of the ethnic groups, many of whom live in remote and relatively underdeveloped areas, are not subjected to epidemiological surveillance and have little awareness of these diseases and their consequences. Geographic and socio-economic factors also play a significant role in some of the joint diseases peculiar to Asian children. In general, the current available data suggests that there are no large differences in the epidemiology and clinical features between the Western and Asian children. This article reviews the available literature on joint diseases in Asian children

  19. MR tomography of the elbow joint

    International Nuclear Information System (INIS)

    MR examinations of the elbow joint of three healthy subjects and a comparison with corresponding sections of anatomical preparations show that MR tomography enables not only an excellent differentiation of muscles, tendons and of the articular capsule, but will also visualise vessels and nerve tracts. MR tomography proved superior to the conventional methods in demonstration of separate fragments and inflammatory changes in the bone on examining 11 pathological elbow joints: congenital malformation, osteochondritis dissecans, ostitis, ulnar and radial nerve lesions, completely healed radius fracture and epicondylitis of the radial and ulnar humerus. Epicondylitis could not be demonstrated by MR. Magnetic resonance tomography seems to be the only method that enables direct visualisation of the nerve paths at the elbow joint. (orig.)

  20. MR tomography of the elbow joint

    Energy Technology Data Exchange (ETDEWEB)

    Zwaan, M.; Rinast, E.; Weiss, H.D.; Pressler, M.; Vogel, H.

    1989-03-01

    MR examinations of the elbow joint of three healthy subjects and a comparison with corresponding sections of anatomical preparations show that MR tomography enables not only an excellent differentiation of muscles, tendons and of the articular capsule, but will also visualise vessels and nerve tracts. MR tomography proved superior to the conventional methods in demonstration of separate fragments and inflammatory changes in the bone on examining 11 pathological elbow joints: congenital malformation, osteochondritis dissecans, ostitis, ulnar and radial nerve lesions, completely healed radius fracture and epicondylitis of the radial and ulnar humerus. Epicondylitis could not be demonstrated by MR. Magnetic resonance tomography seems to be the only method that enables direct visualisation of the nerve paths at the elbow joint.

  1. Branch management into micropipeline joint dot

    Directory of Open Access Journals (Sweden)

    Dimitar Tyanev

    2011-11-01

    Full Text Available This paper considers problems related to hardware implementation of computational process with conditional jumps. Hardware refers to asynchronous pipeline organization at microoperational level. Exploration is dedicated to one of the tasks presented in (Tyanev, D., 2009 concerning to micropipeline controller design to control micropipeline stage into joint dot of branch algorithm. Joint dot is the point at which few preceding branches are combined. It appears inevitably into conditional jump structures and this is the reason for the actuality of its problem. Analysis of this new task is presented and request arbitration functioning principles are formulated for the incoming to joint dot requests. The arbiter is responsible for the fair choice on which depends steady peformance of separate pipeline brances. Paper also describes pipeline controller synthesis and analysis of its operation in two variants: about 2-phase and 4-phase data transfer protocol. The synthesized asynchronous arbiter scheme is invariant to the type of pipeline protocol.

  2. Joint involvement in patients affected by systemic lupus erythematosus: application of the swollen to tender joint count ratio

    OpenAIRE

    E. Cipriano; F. Ceccarelli; L. Massaro; F. R. Spinelli; C. Alessandri; C. Perricone; G. Valesini; Conti, F.

    2015-01-01

    Joint involvement is a common manifestation in systemic lupus erythematosus (SLE). According to the SLE disease activity index 2000 (SLEDAI-2K), joint involvement is present in case of ≥2 joints with pain and signs of inflammation. However this definition could fail to catch all the various features of joint involvement. Alternatively the Swollen to Tender joint Ratio (STR) could be used. This new index, which was originally proposed for rheumatoid arthritis (RA) patients, is based on the cou...

  3. Influence of laser power on microstructure and mechanical properties of fiber laser-tungsten inert gas hybrid welded Mg/Cu dissimilar joints

    International Nuclear Information System (INIS)

    Highlights: • Mg and Cu were joined successfully by laser-TIG hybrid welding process. • Effect of laser power on welded-brazed joints was investigated. • Different newly formed compounds were identified at the Mg/Cu interface. • Al from Mg base metal played an important role in Mg–Al–Cu ternary compound. • Mg–Cu eutectic structure did little harm to mechanical properties. - Abstract: Fiber laser-tungsten inert gas (TIG) hybrid welding technique has been developed for lap joining of dissimilar metals AZ31B Mg alloy to pure copper (T2). The influence of laser power on microstructure and mechanical properties of joints was investigated. The results indicated that acceptable joints could be obtained by adjusting the laser power to the range of 2000–3000 W. In particular, at the laser power of 2500 W the average tensile shear strength reached a maximum of 45.3 MPa, representing a 57% joint efficiency relative to the Mg sheet. Greater or less than 2500 W would cause over or under reaction at the interface, which resulted in the poor joint strength. The different morphologies including Mg–Cu eutectic structure, Mg–Cu intermetallic compound and Mg–Al–Cu ternary intermetallic compound were identified at the Mg/Cu interface. All the joints fractured at the Mg/Cu interface. However, the fracture mode was found to differ. For 2500 W the surface was characterized by tearing edge, while that with poor joint strength was almost dominated by smooth surface or flat tear pattern

  4. Distributed-Computer System Optimizes SRB Joints

    Science.gov (United States)

    Rogers, James L., Jr.; Young, Katherine C.; Barthelemy, Jean-Francois M.

    1991-01-01

    Initial calculations of redesign of joint on solid rocket booster (SRB) that failed during Space Shuttle tragedy showed redesign increased weight. Optimization techniques applied to determine whether weight could be reduced while keeping joint closed and limiting stresses. Analysis system developed by use of existing software coupling structural analysis with optimization computations. Software designed executable on network of computer workstations. Took advantage of parallelism offered by finite-difference technique of computing gradients to enable several workstations to contribute simultaneously to solution of problem. Key features, effective use of redundancies in hardware and flexible software, enabling optimization to proceed with minimal delay and decreased overall time to completion.

  5. Radiodiagnosis of occlusal temporomandibular joint dysfunctions

    International Nuclear Information System (INIS)

    The diagnostic value of conventional oblique-lateral transcranial standard projections for radiography of the temporomandibular joints is limited by various anatomical factors and the projection geometry. Improved results are obtained by individualization of the projection. The author describes a method for determining the individually optimum oblique-lateral projection, a method which is based on pre-exposure fluoroscopy of the temporomandibular joint with an electronic image intensifier system incorporating a television chain. The method has been employed as routine practice for 15 years; it has been modified several times and enables documentation studies to be made with an unusually high degree of reproducibility with respect to beam projection. (Auth.)

  6. Multidetector Computed Tomography in Acute Joint Fractures

    Energy Technology Data Exchange (ETDEWEB)

    Haapamaeki, V.V.; Kiuru, M.J.; Mustonen, A.O.; Koskinen, S.K. [Helsinki Univ. Central Hospital (Finland). Helsinki Medical Imaging Center

    2005-10-01

    Conventional radiography plays an essential diagnostic role in the primary evaluation of acute joint trauma. In complex fractures, however, computed tomography (CT) is an imaging modality often used second to radiography. As a result of technical breakthroughs in the field, multidetector CT (MDCT) allows faster imaging and better temporal, spatial, and contrast resolution compared with conventional single-slice spiral CT. MDCT with multiplanar reformation is helpful in disclosing fracture patterns, particularly in complex joint fractures, where they reveal occult fractures and show the exact number of fracture components and their degree of displacement.

  7. Jointed assembly actuated by fluid pressure

    Science.gov (United States)

    Monroe, John W.

    1992-08-01

    The invention is an assembly of a plurality of relatively movable jointed members such as robotic arm segments and a mechanical muscle connected between two of the segments. The muscle has a longitudinally inflexible, radially expandable sleeve containing a pressurizable bladder of elastic material. The bladder enlarges diametrically when pressurized and bulges the wall of the sleeve outward. The sleeve thereupon contracts axially to compensate for length taken up by the sleeve's outward bulge. Terminus at either end of the sleeve connects the sleeve to different segments of a jointed arm, that the sleeve's axial contraction effects movement of one segment relative to the other.

  8. Recurrent Dislocation of the Shoulder Joint

    OpenAIRE

    Brand, Richard A.

    2008-01-01

    Dr. Anthony F. DePalma is shown. Photograph provided with kind permission of the Art Committee of Thomas Jefferson University, Philadelphia, PA. Dr. DePalma was the first editor of Clinical Orthopaedics and Related Research, established by the recently formed Association of Bone and Joint Surgeons. The idea of forming the Association of Bone and Joint surgeons had been conceived by Dr. Earl McBride of Oklahoma City in 1947, and organized by a group of twelve individuals (Drs. Earl McBride, Ga...

  9. Managing inventory costs through joint procurement programs

    International Nuclear Information System (INIS)

    Given current economic and regulatory challenges, utilities are facing the need to manage inventories more efficiently, lower spare parts costs, and reduce the downtime associated with equipment failure. Two programs helping utilities achieve these goals are the Joint Procurement Corporation (JPC) for multicompany purchase of common equipment and services and the pooled inventory management (PIM) program for joint purchase and storage of nuclear generating unit spare parts. Both of these are cooperative programs that decrease the probability of extended plant outages and reduce duplication of effort and/or inventory among participating utilities

  10. Multidetector Computed Tomography in Acute Joint Fractures

    International Nuclear Information System (INIS)

    Conventional radiography plays an essential diagnostic role in the primary evaluation of acute joint trauma. In complex fractures, however, computed tomography (CT) is an imaging modality often used second to radiography. As a result of technical breakthroughs in the field, multidetector CT (MDCT) allows faster imaging and better temporal, spatial, and contrast resolution compared with conventional single-slice spiral CT. MDCT with multiplanar reformation is helpful in disclosing fracture patterns, particularly in complex joint fractures, where they reveal occult fractures and show the exact number of fracture components and their degree of displacement

  11. Ganglions of the proximal interphalangeal joint.

    Science.gov (United States)

    Cheng, C A; Rockwell, W B

    1999-08-01

    Ganglion cysts-the most common hand tumors-usually affect women in their twenties and thirties. The cause of these cysts is unknown, although trauma has been postulated as an inciting factor. Ganglions occur most commonly at the dorsal and palmar wrist. However, ganglions of the proximal interphalangeal (PIP) joint are rare. Four patients with PIP joint ganglions were recently treated at our institution. Three received aspiration and one received operative therapy, all with good results. All four patients were older than 65 years. PMID:10470671

  12. Joint source-channel video transmission

    CERN Document Server

    Zhai, Fan

    2007-01-01

    This book deals with the problem of joint source-channel video transmission, i.e., the joint optimal allocation of resources at the application layer and the other network layers, such as data rate adaptation, channel coding, power adaptation in wireless networks, quality of service (QoS) support from the network, and packet scheduling, for efficient video transmission. Real-time video communication applications, such as videoconferencing, video telephony, and on-demand video streaming, have gained increased popularity. However, a key problem in video transmission over the existing Internet an

  13. Dislocation of the proximal tibiofibular joint

    Directory of Open Access Journals (Sweden)

    Milankov Miroslav

    2013-01-01

    Full Text Available Introduction. Dislocation of the proximal tibiofibular joint is a rare injury. It occurs during a sports activity that includes rough twisting movements of the bent knee. The role of the proximal tibiofibular joint is to reduce torsional loads to the ankle, to distribute the bending moment of the outer side of tibia, and transfer the vertical load while standing. In the literature there is no larger series; only several cases of the proximal tibiofibular joint dislocation treated by different methods have been published so far. Case Report. A 23-year-old male soccer player sustained an injury after he had joined the game without previous warming-up. He fell on his right side because of a sudden change of direction while his foot was fixed to the base. He felt a severe pain and had a sensation as if something had snapped in his right knee. Pain and swelling at the head of fibula were found by physical examination, which, however, did not reveal any pain, swelling and instability of the ankle or peroneal nerve palsy. The x-ray showed anterolateral dislocation of the proximal tibiofibular joint, Ogden type II. Since manual reposition in general anesthesia failed, open reduction internal fixation was performed and proximal tibiofibular joint was transfixed with a screw. After the wound closure, the above-the-knee plaster cast was applied. The screw was extracted six weeks later, full weight bearing was allowed and he started with physical therapy. Four months after the injury he returned to sports activities. On the follow- up one year after the injury he had the full range of motion of the knee, no complains, and continued with active soccer playing. X-ray showed no signs of arthrosis of the proximal tibiofibular joint. Conclusion. The proximal tibiofibular joint dislocation may be the cause of the chronic pain of the knee so it has to be taken into account when making differential diagnosis in case of the pain at the lateral side of the knee. The

  14. Ka-band waveguide rotary joint

    KAUST Repository

    Yevdokymov, Anatoliy

    2013-04-11

    The authors present a design of a waveguide rotary joint operating in Ka-band with central frequency of 33 GHz, which also acts as an antenna mount. The main unit consists of two flanges with a clearance between them; one of the flanges has three circular choke grooves. Utilisation of three choke grooves allows larger operating clearance. Two prototypes of the rotary joint have been manufactured and experimentally studied. The observed loss is from 0.4 to 0.8 dB in 1.5 GHz band.

  15. TEMPOROMANDIBULAR JOINT ANKYLOSIS: A CASE REPORT

    Directory of Open Access Journals (Sweden)

    Ankita

    2014-04-01

    Full Text Available Ankylosis is a Greek terminology meaning "stiff joint." It can be defined as "inability to open mouth due to either a fibrous or bony union between the head of the condyle and glenoid fossa."1 Temporomandibular joint (TMJ ankylosis is a disorder that leads to a restriction of the mouth opening from partial reduction to complete immobility of the jaw. It is most commonly associated with trauma (13-100%, local or systemic infection (0-53%, or systemic disease, such as ankylosing spondylitis, rheumatoid arthritis, or psoriasis.2, 3

  16. Dynamic energy-based modeling of uranium and cadmium joint toxicity to Caenorhabditis elegans.

    Science.gov (United States)

    Margerit, Adrien; Gomez, Elena; Gilbin, Rodolphe

    2016-03-01

    Toxicokinetic - toxicodynamic energy-based models offer new alternatives to the commonly used approaches for the analysis of mixture toxicity data. Based on the Dynamic Energy Budget theory, DEBtox models enable the description of several endpoints over time simultaneously under the same framework. However, such model still has to be faced with experimental data in a multi-contamination context. In this study, the predictive capacities of a DEBtox model to describe the uranium and cadmium joint toxicity over the entire growth and reproduction period of the soil nematode Caenorhabditis elegans was examined. The two reference additivity approaches, Concentration Addition and Response addition, implemented in the DEBtox model were tested. Assuming no interaction between the two toxicants through Response addition, the DEBtox model allowed a rather accurate fit of the U and Cd joint effects on the growth and reproduction of C. elegans: an interaction between the two metals at the toxicokinetic or toxicodynamic level seems thus unlikely or has only minor consequences. Interestingly, this study underlines that even if the compounds of a mixture share the same DEBtox physiological mode of action (in this case a decrease in assimilation), the Response addition approach may provide a better fit of joint toxicity data than the Concentration addition approach. Moreover, the present work highlighted limitations in the model predictions which are related to the simplifications of the DEBtox framework and its adaptations to the physiology of C. elegans and which lead to an overestimation of the U and Cd joint toxicity in some cases. PMID:26741545

  17. Modeling Progressive Failure of Bonded Joints Using a Single Joint Finite Element

    Science.gov (United States)

    Stapleton, Scott E.; Waas, Anthony M.; Bednarcyk, Brett A.

    2010-01-01

    Enhanced finite elements are elements with an embedded analytical solution which can capture detailed local fields, enabling more efficient, mesh-independent finite element analysis. In the present study, an enhanced finite element is applied to generate a general framework capable of modeling an array of joint types. The joint field equations are derived using the principle of minimum potential energy, and the resulting solutions for the displacement fields are used to generate shape functions and a stiffness matrix for a single joint finite element. This single finite element thus captures the detailed stress and strain fields within the bonded joint, but it can function within a broader structural finite element model. The costs associated with a fine mesh of the joint can thus be avoided while still obtaining a detailed solution for the joint. Additionally, the capability to model non-linear adhesive constitutive behavior has been included within the method, and progressive failure of the adhesive can be modeled by using a strain-based failure criteria and re-sizing the joint as the adhesive fails. Results of the model compare favorably with experimental and finite element results.

  18. Reliability of agriculture universal joint shafts based on temperature measuring in universal joint bearing assemblies

    Directory of Open Access Journals (Sweden)

    Аleksandar Asonja

    2015-03-01

    Full Text Available This paper presents a research into reliability calculations of agriculture double universal joint shafts based on temperature measuring in cardan-type universal joint bearing assemblies. Special laboratory equipment was developed for this research which is presented in the paper. The objective of this research was to test the real life span of universal joint shafts in the laboratory and in field, to obtain the results which can be used to improve the reliability of universal joint shafts. If the presented research were used along with maintenance measures recommended in the paper and with proper use, the level of reliability of the shafts would be 2.1 times higher. The presented results of the research showed that needle bearings, i.e. bearing assemblies of the joints, are the most critical elements on universal joint shafts and are possible causes of their lower reliability. The second universal joint is the part with the lowest reliability in the observed technical system.

  19. Characterization of Sulfur Compounds in MTBE

    OpenAIRE

    Mingqing Wu; Chunyan Chang; Tao Li; Jian Zhou; Liping Zhao

    2015-01-01

    A study is carried out on chemical constitution of sulfur compounds in MTBE and their formation mechanisms. These sulfur compounds are classified into three types: common sulfur compounds, newly formed sulfur compounds, and high boiling sulfur compounds. Common sulfur compounds which include mercaptans, low molecule sulfides and disulfides, are directly from C4, one of the stocks for production of MTBE. The newly formed sulfur compounds, with one sulfur atom and five or more total carbon atom...

  20. Nomenclature on an organic compound (I)

    International Nuclear Information System (INIS)

    This book is about nomenclature on an organic compound, which includes introduction with general principle on nomenclature on compounds it describes hydrocarbon like terpene hydrocarbon, basic heterocyclic organic compound including carbon, hydrogen, oxygen, nitrogen, halogen, sulfur, selenium and tellurium such as nomenclature system, halogen derivatives, alcohol and phenol derivatives, compound with sulfur, amino, nitroso and nitro compound, amino radical ion, azo and azoxy compound, compound including an atom group, hydrazine and derivatives.

  1. Regulation of Compound Leaf Development

    Directory of Open Access Journals (Sweden)

    Yuan Wang

    2013-12-01

    Full Text Available Leaf morphology is one of the most variable, yet inheritable, traits in the plant kingdom. How plants develop a variety of forms and shapes is a major biological question. Here, we discuss some recent progress in understanding the development of compound or dissected leaves in model species, such as tomato (Solanum lycopersicum, Cardamine hirsuta and Medicago truncatula, with an emphasis on recent discoveries in legumes. We also discuss progress in gene regulations and hormonal actions in compound leaf development. These studies facilitate our understanding of the underlying regulatory mechanisms and put forward a prospective in compound leaf studies.

  2. Microstructure Evolution and Shear Behavior of the Solder Joints for Flip-Chip LED on ENIG Substrate

    Science.gov (United States)

    Liu, Yang; Sun, Fenglian; Luo, Liangliang; Yuan, Cadmus A.; Zhang, Guoqi

    2015-07-01

    The microstructure evolution and shear behavior of the solder joints for the flip-chip light-emitting diode on the electroless nickel/immersion gold (ENIG) substrate were investigated in this study. The experimental results reveal that the solder joints for the anode and cathode have different microstructures and failure characteristics during the shear test before and after isothermal aging. For the solder joints for the anode, the interfacial intermetallic compound (IMC) is (Au, Ni)Sn4 at the solder/anode interface but dendritic Ni3Sn4 grains at the solder/ENIG interface after reflow. Meanwhile, the dendritic Ni3Sn4 grains are surrounded by (Au, Ni)Sn4, which suppresses the growth of the Ni3Sn4 grains during aging. For the solder joints for the cathode, a nano scaled Au-rich layer can be observed near the cathode/solder layer interface after reflow. And the Au-rich layer moves toward the bulk solder because of the volume expansion by the transformation from Au into (Au, Ni)Sn4 during reflow and isothermal aging. Due to the diffusion of the Au atom from the Au-rich layer into the bulk solder, the Au-rich layer transformed into an interface inside of the solder joint. The average shear force of the solder joints shows a decrease from 380 gf to 250 gf because of the microstructure evolution during the isothermal aging for 1000 h at 85°C. After long time aging, the primary failure mode of the solder joint for the anode changed from the anode broken to the brittle failure of the solder layer. The delamination between the IMC layer and the insulation layer is suggested to be the dominated failure mode of the solder joint for the cathode after aging.

  3. Norsk-russiske joint ventures : hvorfor lykkes enkelte norsk-russiske joint ventures, mens andre mislykkes?

    OpenAIRE

    Berge, Odd Magne; Kjelling, Peter

    2009-01-01

    Denne oppgaven omhandler joint ventures mellom norske og russiske bedrifter. Vi har jobbet ut fra problemstillingen ”Hvorfor lykkes enkelte norsk-russiske joint ventures, mens andre mislykkes?” Dette er et interessant tema fordi Russland er- og har lenge vært en viktig handelspartner for Norge. I tillegg har det ikke vært gjort mye forskning på fenomenet norsk-russiske joint ventures tidligere. Russland er et stort og mektig land, rikt på ressurser og med en økonomi som stad...

  4. Complications Related to Metal-on-Metal Articulation in Trapeziometacarpal Joint Total Joint Arthroplasty

    OpenAIRE

    Christina Frølich; Torben Bæk Hansen

    2015-01-01

    Adverse reactions to metal-on-metal (MoM) prostheses are well known from total hip joint resurfacing arthroplasty with elevated serum chrome or cobalt, pain and pseudo tumor formation. It may, however, also be seen after total joint replacement of the trapeziometacarpal joint using MoM articulation, and we present two cases of failure of MoM prostheses due to elevated metal-serum levels in one case and pseudo tumor formation in another case. Furthermore, we suggest a diagnostic algorithm for ...

  5. Effect of chord can length on strength of T joints

    Energy Technology Data Exchange (ETDEWEB)

    Madros, M.S.Z.; Zettlemoyer, N.; Healy, B.E.

    1995-12-01

    A study has been conducted to examine the influence of can length on the static strength of compression loaded T-joints. Finite Element models of the T-joints are developed and analyzed using the SESAM/Pretube, PATRAN{reg_sign}, and ABAQUS{trademark} computer programs. The ultimate loads from the analyses are compared with recommended values in API (1993) and other codes. In general, it appears that the API recommended ultimate strength values for T joints with low {beta} should be modified. Also, the API derating equation for X joints with short cans is conservative for T joints. However, a derating equation is required for T joints.

  6. Decision Fusion System for Bolted Joint Monitoring

    Directory of Open Access Journals (Sweden)

    Dong Liang

    2015-01-01

    Full Text Available Bolted joint is widely used in mechanical and architectural structures, such as machine tools, industrial robots, transport machines, power plants, aviation stiffened plate, bridges, and steel towers. The bolt loosening induced by flight load and environment factor can cause joint failure leading to a disastrous accident. Hence, structural health monitoring is critical for the bolted joint detection. In order to realize a real-time and convenient monitoring and satisfy the requirement of advanced maintenance of the structure, this paper proposes an intelligent bolted joint failure monitoring approach using a developed decision fusion system integrated with Lamb wave propagation based actuator-sensor monitoring method. Firstly, the basic knowledge of decision fusion and classifier selection techniques is briefly introduced. Then, a developed decision fusion system is presented. Finally, three fusion algorithms, which consist of majority voting, Bayesian belief, and multiagent method, are adopted for comparison in a real-world monitoring experiment for the large aviation aluminum plate. Based on the results shown in the experiment, a big potential in real-time application is presented that the method can accurately and rapidly identify the bolt loosening by analyzing the acquired strain signal using proposed decision fusion system.

  7. Arthroscopic management of painful first metatarsophalangeal joint

    Directory of Open Access Journals (Sweden)

    Debnath U

    2005-01-01

    Full Text Available Background: Arthroscopy of the great toe MTP joint has been practiced with favourable outcomes. A range of indications have been described ranging from synovitis to osteochondral defects. The purpose of the present study was to describe our technique and to assess the functional outcome following arthroscopic management of Hallux MTP disorders using AOFAS scoring system. Methods: We describe the technique of Hallux MTP joint arthroscopy in twenty patients. Indications included hallux rigidus with osteophytes, chondromalacia, OCDs, loose bodies, arthrofibrosis, synovitis, tophaceous gout arthritis and intra-articular fractures of MTP joint. All patients had been evaluated clinically and radiologically with record of their AOFAS scores pre-operatively. At a minimum follow-up of two years the clinical assessment was carried out with AOFAS scores. Results: The mean pre-operative and post-operative AOFAS score were 47 (range 10-78 and 97 (87 -100 respectively. The patient with intra-articular fracture had an excellent outcome following arthroscopic reduction of the fracture. Conclusion: Arthroscopic management of painful hallucial MTP joint is a specialized technique, which if performed for the right indications, gives a favourable outcome with minimal complications.

  8. Interactive segmentation of Hip Joint Cartilage

    Czech Academy of Sciences Publication Activity Database

    Dvořák, Pavel; Juráš, V.; Vogl, W.; Chytil, J.

    Cambridge: The Electromagnetics Academy, 2014, s. 2369-2372. ISBN 978-1-934142-28-8. [PIERS 2014. Progress In Electromagnetics Research Symposium /35./. Guangzhou (CN), 25.08.2014-28.08.2014] R&D Projects: GA ČR GAP102/12/1104 Institutional support: RVO:68081731 Keywords : hip joint * MRI * segmentation of cartilage Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering

  9. 2016 Joint Universities Accelerator School (JUAS) - Registrations

    CERN Multimedia

    2015-01-01

    The registrations for the 2016 session of the Joint Universities Accelerator School (JUAS) are now open.   Applications are welcome from second-year Master and PhD and for physicists wishing to further their knowledge in this particular field. The deadline for submission of the full application form is 30 October 2015.

  10. Joint ventures and concentrations in oil market

    International Nuclear Information System (INIS)

    Many are the joint ventures taken during last year by the oil companies as a move towards the ever existing rules of the oil market: integration, economies of scale and reduction of competitive market uncertainty. This article discusses some of the most interesting points of the recent events and the initiatives in the Italian market

  11. Biochemical Markers of Joint Tissue Turnover

    DEFF Research Database (Denmark)

    Bay-Jensen, Anne-Christine; Sondergaard, Bodil Cecilie; Christiansen, Claus;

    2009-01-01

    available for the study of tissue turnover in each of the three compartments of the articular joint, that is the bone, the cartilage, and the synovium. Finally, we provide some perspective to future developments in biomarker discovery and discuss the potential impact such technologies could have on the drug...

  12. Automatically Locking/Unlocking Orthotic Knee Joint

    Science.gov (United States)

    Weddendorf, Bruce

    1994-01-01

    Proposed orthotic knee joint locks and unlocks automatically, at any position within range of bend angles, without manual intervention by wearer. Includes tang and clevis, locks whenever wearer transfers weight to knee and unlocks when weight removed. Locking occurs at any angle between 45 degrees knee bend and full extension.

  13. Ultrasound findings of the locked metacarpophalangeal joint

    Energy Technology Data Exchange (ETDEWEB)

    Wessely, Kathryn; Healy, Jeremiah; Lee, Justin [Chelsea and Westminster Hospital, Department of Radiology, London (United Kingdom); Owers, Kate [Chelsea and Westminster Hospital, Department of Trauma and Orthopaedics Hand Unit, London (United Kingdom)

    2009-01-15

    The radiographs and sonographic findings of two cases of locked metacarpophalangeal joint secondary to tethering of the volar plate are described. The presence of osteophytes and the dynamic ultrasound assessment of the volar plate have provided confirmation of the clinical diagnosis prior to surgery. (orig.)

  14. Finger-jointed beams in bending

    DEFF Research Database (Denmark)

    Andreasen, Lotte; Hoffmeyer, Preben

    1997-01-01

    An investigation of the dynamic and static fatique of finger-jointed beams in bending was carried out. Results were obtained for five different frequencies from static loading to a load cycle period of two minutes. A total of seven series were long-term tested and five series were short-term tested...

  15. Joint Individual-Group Modeling for Tracking.

    Science.gov (United States)

    Bazzani, Loris; Zanotto, Matteo; Cristani, Marco; Murino, Vittorio

    2015-04-01

    We present a novel probabilistic framework that jointly models individuals and groups for tracking. Managing groups is challenging, primarily because of their nonlinear dynamics and complex layout which lead to repeated splitting and merging events. The proposed approach assumes a tight relation of mutual support between the modeling of individuals and groups, promoting the idea that groups are better modeled if individuals are considered and vice versa. This concept is translated in a mathematical model using a decentralized particle filtering framework which deals with a joint individual-group state space. The model factorizes the joint space into two dependent subspaces, where individuals and groups share the knowledge of the joint individual-group distribution. The assignment of people to the different groups (and thus group initialization, split and merge) is implemented by two alternative strategies: using classifiers trained beforehand on statistics of group configurations, and through online learning of a Dirichlet process mixture model, assuming that no training data is available before tracking. These strategies lead to two different methods that can be used on top of any person detector (simulated using the ground truth in our experiments). We provide convincing results on two recent challenging tracking benchmarks. PMID:26353291

  16. Sacroiliac Joint Pain and Its Treatment.

    Science.gov (United States)

    Rashbaum, Ralph F; Ohnmeiss, Donna D; Lindley, Emily M; Kitchel, Scott H; Patel, Vikas V

    2016-03-01

    The sacroiliac joint (SIJ) as a source of symptoms has been controversial; however, as knowledge about the joint increased, its role as a pain generator in patients complaining of symptoms that are often attributed to spinal pathology has become better appreciated. The literature reports that the SIJ is the pain origin in as many as 30% of patients presenting with low back pain. Clinically, the SIJ can be challenging to evaluate; however, assessing pain location, patient posture/movement, and provocative manual testing are useful in making the presumptive diagnosis of SIJ disruption. The most definitive evaluation is image-guided injection of anesthetic solutions into the joint which is diagnostic if there is at least 75% symptom relief acutely. Treatment begins with nonoperative intervention including physical therapy and/or chiropractic care. If these fail, the next option is generally radiofrequency denervation (rhizotomy) of the joint. If this does not provide adequate relief, surgical intervention, in the form of minimally invasive SIJ fusion may be considered. The literature increasingly supports favorable results of SIJ fusion in appropriately selected patients. The purpose of this review is to provide an overview of the current literature on the SIJ, with focus on its surgical treatment. PMID:26889985

  17. Wave Propagation in Jointed Geologic Media

    Energy Technology Data Exchange (ETDEWEB)

    Antoun, T

    2009-12-17

    Predictive modeling capabilities for wave propagation in a jointed geologic media remain a modern day scientific frontier. In part this is due to a lack of comprehensive understanding of the complex physical processes associated with the transient response of geologic material, and in part it is due to numerical challenges that prohibit accurate representation of the heterogeneities that influence the material response. Constitutive models whose properties are determined from laboratory experiments on intact samples have been shown to over-predict the free field environment in large scale field experiments. Current methodologies for deriving in situ properties from laboratory measured properties are based on empirical equations derived for static geomechanical applications involving loads of lower intensity and much longer durations than those encountered in applications of interest involving wave propagation. These methodologies are not validated for dynamic applications, and they do not account for anisotropic behavior stemming from direcitonal effects associated with the orientation of joint sets in realistic geologies. Recent advances in modeling capabilities coupled with modern high performance computing platforms enable physics-based simulations of jointed geologic media with unprecedented details, offering a prospect for significant advances in the state of the art. This report provides a brief overview of these modern computational approaches, discusses their advantages and limitations, and attempts to formulate an integrated framework leading to the development of predictive modeling capabilities for wave propagation in jointed and fractured geologic materials.

  18. Synovial osteochondromatosis of the temporomandibular joint

    International Nuclear Information System (INIS)

    Synovial osteochondromatosis (SO) is a meta plastic process by which synovial mesenchymal cells transform into chondroblasts and chondrocytes. This disease affects most frequently the knee, the hip, the elbow, and uncommonly the temporomandibular joint (TMJ). The authors present 2 cases of synovial osteochondromatosis of the TMJ. (author)

  19. Designing an International Joint Venture Negotiation Game.

    Science.gov (United States)

    Kenkel, Phil; And Others

    1996-01-01

    Evaluates a simulation game that models management problems encountered in negotiating and managing international joint ventures. Designed to instruct executives of state-owned agribusinesses in Indonesia in abstract concepts such as partner rapport, transfer price conflicts, and marketing disagreements, its success suggests that simulation games…

  20. Surgical management of temporomandibular joint ankylosis.

    Science.gov (United States)

    Maki, Mohammed Hashim; Al-Assaf, Dhuha A

    2008-11-01

    Ankylosis of the temporomandibular joint (TMJ) is one of the causes of persistent and progressive limitation of mouth opening. It usually requires to be corrected surgically; an intervention not without complications. This study was conducted in a central surgical hospital in Iraq (Baghdad) in the era hallmarked by shortage of nearly all facilities needed to accomplish solutions for a surgical task. The surgical procedure is displayed along with modifications, complications, and follow-up protocol. Fifteen patients (21 joints) have been treated surgically for TMJ ankylosis of different severities. All patients were treated at the Department of Oral and Maxillofacial Surgery, Specialized Surgical Hospital-Baghdad Medical City, Iraq. The study was carried out in the period between 1998 and 2002 (inclusive). Patients' ages ranged between 4 and 52 years. In addition to the clinical diagnoses, further evaluation of the ankylosis area was assisted by the use of orthopantomography and spiral computerized scanning (axial, coronal sections, and three-dimensional views). Maximal incisal opening was registered before and after surgery for further follow-up evaluation. Al-Kayat and Bramely approach is advocated to expose the joint area. All 21 joints were operated through blind nasoendotracheal intubation general anesthesia. Computed tomography scans, wide exposures, aggressive resections, proper interposition materials, strict postoperative physiotherapy, and good family and patient compliance all may decrease the possibility of relapse and offer better results. Early management of TMJ ankylosis is important if more damage in orofacial structures and consolidation of bony union are to be avoided. PMID:19098556

  1. Joint production and price uncertainty: hypothesis tests

    OpenAIRE

    Alghalith, Moawia

    2006-01-01

    This paper extends the existing estimation methods to allow empirical estimation and hypothesis testing under joint production and price uncertainty. Our approach modifies and expands the use of duality theory. Furthermore, our approach does not require the specification or estimation of the production/cost function. We apply the methodology to the U.S. manufacturing sector.

  2. The neuromuscular differential diagnosis of joint hypermobility

    NARCIS (Netherlands)

    Donkervoort, S.; Bonnemann, C.G.; Loeys, B.L.; Jungbluth, H.; Voermans, N.C.

    2015-01-01

    Joint hypermobility is the defining feature of various inherited connective tissue disorders such as Marfan syndrome and various types of Ehlers-Danlos syndrome and these will generally be the first conditions to be considered by geneticists and pediatricians in the differential diagnosis of a patie

  3. The functional consequences of Generalized Joint Hypermobility

    DEFF Research Database (Denmark)

    Scheper, Mark C; de Vries, Janneke E; Juul-Kristensen, Birgit;

    2014-01-01

    BACKGROUND: Generalized Joint Hypermobility (GJH) has been found to be associated with musculoskeletal complaints and disability. For others GJH is seen as a prerequisite in order to excel in certain sports like dance. However, it remains unclear what the role is of GJH in human performance...

  4. Space Suit Joint Torque Measurement Method Validation

    Science.gov (United States)

    Valish, Dana; Eversley, Karina

    2012-01-01

    In 2009 and early 2010, a test method was developed and performed to quantify the torque required to manipulate joints in several existing operational and prototype space suits. This was done in an effort to develop joint torque requirements appropriate for a new Constellation Program space suit system. The same test method was levied on the Constellation space suit contractors to verify that their suit design met the requirements. However, because the original test was set up and conducted by a single test operator there was some question as to whether this method was repeatable enough to be considered a standard verification method for Constellation or other future development programs. In order to validate the method itself, a representative subset of the previous test was repeated, using the same information that would be available to space suit contractors, but set up and conducted by someone not familiar with the previous test. The resultant data was compared using graphical and statistical analysis; the results indicated a significant variance in values reported for a subset of the re-tested joints. Potential variables that could have affected the data were identified and a third round of testing was conducted in an attempt to eliminate and/or quantify the effects of these variables. The results of the third test effort will be used to determine whether or not the proposed joint torque methodology can be applied to future space suit development contracts.

  5. The Joint Physics Analysis Center Website

    CERN Document Server

    Mathieu, Vincent

    2016-01-01

    The Joint Physics Analysis Center is a collaboration between theorists and experimentalists working in hadronic physics. In order to facilitate the exchange of information between the different actors in hadron spectroscopy, we created an interactive website. In this note, I summarize the first projects available on the website.

  6. Transducer Joint for Kidney-Stone Ultrasonics

    Science.gov (United States)

    Angulo, E. D.

    1983-01-01

    Ultrasonic therapy for kidney stones improved by new way of connecting wire-probe ultrasonic waveguide to transducer. Improved mounting allows joint to last long enough for effective treatment. Sheath and rubber dampers constrain lateral vibration of wire waveguide. Combination of V-shaped mounting groove, sheath, and rubber dampers increases life expectancy of wire 15 times or more.

  7. 29 CFR 570.115 - Joint applicability.

    Science.gov (United States)

    2010-07-01

    ... Regulations Relating to Labor (Continued) WAGE AND HOUR DIVISION, DEPARTMENT OF LABOR REGULATIONS CHILD LABOR REGULATIONS, ORDERS AND STATEMENTS OF INTERPRETATION General Statements of Interpretation of the Child Labor... 12(a) and 12(c) § 570.115 Joint applicability. The child labor coverage provisions contained...

  8. Failure of dissimilar material bonded joints

    Science.gov (United States)

    Konstantakopoulou, M.; Deligianni, A.; Kotsikos, G.

    2016-03-01

    Joining of materials in structural design has always been a challenge for engineers. Bolting and riveting has been used for many years, until the emergence of fusion welding which revolutionised construction in areas such as shipbuilding, automotive, infrastructure and consumer goods. Extensive research in the past 50 years has resulted in better understanding of the process and minimised the occurrence of failures associated with fusion welding such as, residual stress cracking, stress corrosion and corrosion fatigue cracking, localised reduction in mechanical properties due to microstructural changes (heat affected zone) etc. Bonding has been a technique that has been proposed as an alternative because it eliminates several of the problems associated with fusion welding. But, despite some applications it has not seen wide use. There is however a renewed interest in adhesively bonded joints, as designers look for ever more efficient structures which inevitably leads to the use and consequently joining of combinations of lightweight materials, often with fundamentally different mechanical and physical properties. This chapter provides a review of adhesively bonded joints and reports on improvements to bonded joint strength through the introduction of carbon nanotubes at the bond interface. Results from various workers in the field are reported as well as the findings of the authors in this area of research. It is obvious that there are several challenges that need to be addressed to further enhance the strength of bonded joints and worldwide research is currently underway to address those shortcomings and build confidence in the implementation of these new techniques.

  9. Joint Local Quasinilpotence and Common Invariant Subspaces

    Indian Academy of Sciences (India)

    A Fernández Valles

    2006-08-01

    In this article we obtain some positive results about the existence of a common nontrivial invariant subspace for -tuples of not necessarily commuting operators on Banach spaces with a Schauder basis. The concept of joint quasinilpotence plays a basic role. Our results complement recent work by Kosiek [6] and Ptak [8].

  10. CHINA-MALAYSIA JOINT SEMINAR ON SPACE

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    In conjunction with the 30th anniversary of diplomatic relationship between China and Malaysia, a seminar on Space for Sustainable Development was jointly held by China National Space Administration (CNSA) and National Space Agency of Malaysia on 2-4 September, 2004 in Kuala Lumpur, Malaysia.

  11. The Joint Dynamics of Equity Market Factors

    DEFF Research Database (Denmark)

    Christoffersen, Peter; Langlois, Hugues

    2013-01-01

    The 4 equity market factors from Fama and French (1993) and Carhart (1997) are pervasive in academia and practice. However, not much is known about their joint distribution and dynamics. We find striking evidence of asymmetric tail dependence across the factors. While the linear factor correlations...

  12. Computational Biomechanics of the Wrist Joint

    CERN Document Server

    Nazri Bajuri, Mohd

    2013-01-01

    This book presents an analysis of the stress distribution and contact stresses in severe rheumatoid wrist after total wrist arthroplasty. It assesses and compares the load transfer throughout the joint and contact pressure at the articulations. The data obtained from this study is of importance as this provide greater evidence to the benefits of total wrist arthroplasty in rheumatoid arthritis patients.

  13. Report of the Joint Accounting Group.

    Science.gov (United States)

    Western Interstate Commission for Higher Education, Boulder, CO. National Center for Higher Education Management Systems.

    The Joint Accounting Group (JAG) has as its primary goal to develop a capability to provide uniform transactional finance data at the institutional level. Such data should effectively meet the needs of public reporting, institutional financial management, and program planning. The group believes that the attainment of this goal requires uniformly…

  14. Structural Simulation of a Bone-Prosthesis System of the Knee Joint

    Directory of Open Access Journals (Sweden)

    Aivars Zemitis

    2008-09-01

    Full Text Available In surgical knee replacement, the damaged knee joint is replaced with artificial prostheses. An accurate clinical evaluation must be carried out before applying knee prostheses to ensure optimal outcome from surgical operations and to reduce the probability of having long-term problems. Useful information can be inferred from estimates of the stress acting onto the bone-prosthesis system of the knee joint. This information can be exploited to tailor the prosthesis to the patient’s anatomy. We present a compound system for pre-operative surgical planning based on structural simulation of the bone-prosthesis system, exploiting patient-specific data.

  15. Crystallographic properties of fertilizer compounds

    Energy Technology Data Exchange (ETDEWEB)

    Frazier, A.W.; Dillard, E.F.; Thrasher, R.D.; Waerstad, K.R.; Hunter, S.R.; Kohler, J.J.; Scheib, R.M.

    1991-02-01

    This bulletin is a compilation of crystallographic data collected at NFERC on 450 fertilizer-related compounds. In TVA's fertilizer R and D program, petrographic examination, XRD, and infrared spectroscopy are combined with conventional chemical analysis methods in identifying the individual compounds that occur in fertilizer materials. This handbook brings together the results of these characterization studies and supplemental crystallographic data from the literature. It is in one-compound-per-page, loose-leaf format, ordered alphabetically by IUPAC name. Indexes provided include IUPAC name, formula, group, alternate formula, synonyms, x-ray data, optical data. Tables are given for solids, compounds in commercial MAP and DAP, and matrix materials in phosphate rock.

  16. The precipitation of vanadium compounds

    International Nuclear Information System (INIS)

    The results of a study on the chemistry of the precipitation process of vanadium compounds in sulfuric media are presented, in order to recover the vanadium contained in the ore from Campo Alegre de Lourdes (Bahia-Brazil). (Author)

  17. Optimization of compound gear pump

    Institute of Scientific and Technical Information of China (English)

    栾振辉

    2002-01-01

    This paper introduces the performances of compound gear pump. Based on the target of having the smallest mass per unit volume, the paper established a mathematical model of optimization, and obtained the results of optimization of the pump.

  18. Fourth symposium on macrocyclic compounds

    International Nuclear Information System (INIS)

    Both theoretical and experimental aspects of the properties and behavior of synthetic and naturally occurring macrocyclic compounds are covered in this symposium. This document contains abstracts of the papers

  19. The demise of compound houses

    DEFF Research Database (Denmark)

    Andreasen, Jørgen; Eskemose Andersen, Jørgen

    2006-01-01

    The compound house has long provided the accomodation required by low income households in West African cities. In Kumasi, Ghana, evidence suggests that no new compounds are being built. Instead, the city is being ringed by relatively affluent villa-style development while neighbourhoods dominated...... the neighbourhood unity is a challenge for urban planners. However they represent good value for money, cost little to build, suit traditional inheritence patterns, allow independent life at low cost and allow sharing of services with a finite and known group (albeit within a potential conflictive...... characteristics of compound housing and analyses the advantages and disadvantages of life within such housing in Kumasi. Issues of privacy, image and communal life are usually cited by occupants dissatiesfied with life in compound houses, and the difficulty of extending them without spoiling the open spaces and...

  20. Compounding in synthetic aperture imaging

    DEFF Research Database (Denmark)

    Hansen, J. M.; Jensen, J. A.

    2012-01-01

    A method for obtaining compound images using synthetic aperture data is investigated using a convex array transducer. The new approach allows spatial compounding to be performed for any number of angles without reducing the frame rate or temporal resolution. This important feature is an intrinsic...... from multiple spherical emissions to synthesize multiple transmit and receive apertures, corresponding to imaging the tissue from multiple directions. The many images are added incoherently, to produce a single compound image. Using a 192-element, 3.5-MHz, λ-pitch transducer, it is demonstrated from...... tissue-phantom measurements that the speckle is reduced and the contrast resolution improved when applying synthetic aperture compound imaging. At a depth of 4 cm, the size of the synthesized apertures is optimized for lesion detection based on the speckle information density. This is a performance...