WorldWideScience

Sample records for chromium additions

  1. Process for improving moisture resistance of epoxy resins by addition of chromium ions

    Science.gov (United States)

    St.clair, A. K.; Stoakley, D. M.; St.clair, T. L.; Singh, J. J. (Inventor)

    1985-01-01

    A process for improving the moisture resistance properties of epoxidized TGMDA and DGEBA resin system by chemically incorporating chromium ions is described. The addition of chromium ions is believed to prevent the absorption of water molecules.

  2. Chromium

    Science.gov (United States)

    ... Intern Med 1991;115:917-24. Abraham AS, Brooks BA, Eylath U. The effects of chromium supplementation on serum glucose and lipids in patients with and without non-insulin-dependent diabetes. Metabolism 1992;41:768-71. Hermann J, Arquitt A. ...

  3. Experimental Copper Deficiency, Chromium Deficiency and Additional Molybdenum Supplementation in Goats – Pathological Findings

    Directory of Open Access Journals (Sweden)

    Frank A

    2001-09-01

    Full Text Available Secondary copper (Cu deficiency, chromium (Cr deficiency and molybdenosis (Mo has been suggested to cause the "mysterious" moose disease in the southwest of Sweden. The present experiment was performed on goats to investigate the clinical, chemical, and pathological alterations after 20 months feeding of a semi-synthetic diet deficient in Cu and Cr. Four groups were included in the study: control group (n = 4, Cu-deficient group (group 1, n = 4, Cr-deficient group (group 2, n = 2 and Cu+Cr-deficient group (group 3, n = 3. Group 3 was additionally supplemented with tetrathiomolybdate during the last 2 months of the experiment. Main histopathological findings in groups 1 and 3 were the lesions in the liver, characterised by a severe active fibrosis, bile duct proliferation, haemosiderosis and mild necroses. Additionally, degenerative alterations of the exocrine pancreas were prominent in groups 1 and 3. Lesions in group 3 were more pronounced than in group 1. In group 3, the skin showed an atrophic dermatosis, while in group 2 a crusty dermatitis caused by Candida spp. was observed. This study shows that liver, pancreas and skin are mainly affected by a long term deficiency of copper and the findings are complicated by molybdenum application while chromium deficiency produced no histomorphological effects in our study.

  4. The Effect of Silicon and Aluminum Additions on the Oxidation Resistance of Lean Chromium Stainless Steels

    Energy Technology Data Exchange (ETDEWEB)

    Dunning, J.S.; Alman, D.E.; Rawers, J.C.

    2001-09-01

    The effect of Si and Al additions on the oxidation of lean chromium austenitic stainless steels has been studied. A baseline composition of Fe-16Cr-16Ni-2Mn-1Mo was selected to allow combined Si and Al additions of up to 5 wt. pct. in a fully austenitic alloy. The baseline composition was selected using a net Cr equivalent equation to predict the onset of G-ferrite formation in austenite. Cyclic oxidation tests in air for 1000 hours were carried out on alloys with Si only or combined Si and Al additions in the temperature range 700 C to 800 C. Oxidation resistance of alloys with Si only additions were outstanding, particularly at 800 C. It was evident that different rate controlling mechanisms for oxidation were operative at 700 C and 800 C in the Si alloys. In addition, Si alloys pre-oxidized at 800 C, showed a zero weight gain in subsequent testing for 1000 hours at 700 C. The rate controlling mechanism in alloys with combined Si and Al addition for oxidation at 800 C was also different than alloys with Si only. SEM and ESCA analysis of the oxide films and base material at the oxide/base metal interface were conducted to study potential rate controlling mechanisms.

  5. Effect of Ti-V-Nb-Mo addition on microstructure of high chromium cast iron

    Directory of Open Access Journals (Sweden)

    Ma Youping

    2012-05-01

    Full Text Available The effects of trace additions of multi-alloying elements (Ti, Nb, V, Mo on carbides precipitation and as-cast microstructure of eutectic high chromium cast iron containing 2.85wt.%C and 31.0wt.%Cr were investigated from thermodynamic and kinetic considerations. The thermodynamic calculations show that Ti and Nb exist in the multi-alloying system in the forms of TiC and NbC. The formation of VC during the solidification is not feasible from the thermodynamic consideration. XRD analysis shows that the V exists in alloy compounds (VCr2C2, VCrFe8. The first precipitated high melting point particles (TiC, NbC can act as the heterogeneous substrate of M7C3 carbides, which results in significant refinement of the M7C3 carbides. After the addition of alloying elements, C atom diffusion is hindered due to the strong affinities of the strong carbide forming elements for carbon, which decreases the growth rate of carbides. The combined roles of the increase of nucleation rate and the decrease of carbides growth rate lead to the finer microstructure.

  6. Microbial community response to addition of polylactate compounds to stimulate hexavalent chromium reduction in groundwater.

    Science.gov (United States)

    Brodie, Eoin L; Joyner, Dominique C; Faybishenko, Boris; Conrad, Mark E; Rios-Velazquez, Carlos; Malave, Josue; Martinez, Ramon; Mork, Benjamin; Willett, Anna; Koenigsberg, Steven; Herman, Donald J; Firestone, Mary K; Hazen, Terry C

    2011-10-01

    To evaluate the efficacy of bioimmobilization of Cr(VI) in groundwater at the Department of Energy Hanford site, we conducted a series of microcosm experiments using a range of commercial electron donors with varying degrees of lactate polymerization (polylactate). These experiments were conducted using Hanford Formation sediments (coarse sand and gravel) immersed in Hanford groundwater, which were amended with Cr(VI) and several types of lactate-based electron donors (Hydrogen Release Compound, HRC; primer-HRC, pHRC; extended release HRC) and the polylactate-cysteine form (Metal Remediation Compound, MRC). The results showed that polylactate compounds stimulated an increase in bacterial biomass and activity to a greater extent than sodium lactate when applied at equivalent carbon concentrations. At the same time, concentrations of headspace hydrogen and methane increased and correlated with changes in the microbial community structure. Enrichment of Pseudomonas spp. occurred with all lactate additions, and enrichment of sulfate-reducing Desulfosporosinus spp. occurred with almost complete sulfate reduction. The results of these experiments demonstrate that amendment with the pHRC and MRC forms result in effective removal of Cr(VI) from solution most likely by both direct (enzymatic) and indirect (microbially generated reductant) mechanisms.

  7. The content of chromium and copper in plants and soil fertilized with sewage sludge with addition of various amounts of CaO and lignite ash

    Directory of Open Access Journals (Sweden)

    Wysokiński Andrzej

    2016-09-01

    Full Text Available The influence of fertilization with fresh sewage sludge with the addition of calcium oxide and lignite ash in the proportions dry mass 6:1, 4:1, 3:1 and 2:1 on the content of chromium and copper in plants and soil and uptake of these elements was investigated in pot experiment. Sewage sludge were taken from Siedlce (sludge after methane fermentation and Łuków (sludge stabilized in oxygenic conditions, eastern Poland. The chromium content in the biomass of the test plants (maize, sunflower and oat was higher following the application of mixtures of sewage sludge with ash than of the mixtures with CaO. The copper content in plants most often did not significantly depend on the type of additives to the sludge. Various amounts of additives to the sewage sludge did not have a significant effect on the contents of either of the studied trace elements in plants. The contents of chromium and copper in soil after 3 years of cultivation of plants were higher than before the experiment, but these amounts were not significantly differentiated depending on the type and the amount of the used additive (i.e. CaO vs. ash to sewage sludge.

  8. [Immunobiological blood parameters in rabbits after addition to the diet suspensions of chlorella, sodium sulfate, citrate and chromium chloride].

    Science.gov (United States)

    Lesyk, Ia V; Fedoruk, R S; Dolaĭchuk, O P

    2013-01-01

    We studied the content of glycoproteins and their individual carbohydrate components, the phagocyte activity of neutrophils, phagocyte index, phagocyte number lizotsym and bactericidal activity of the serum concentration of circulating immune complexes and middle mass molecules in the blood of rabbits following administration into the diet chlorella suspension, sodium sulfate, chromium citrate and chromium chloride. The studies were conducted on rabbits weighing 3.7-3.9 kg with altered diet from the first day of life to 118 days old. Rabbits were divided into five groups: the control one and four experimental groups. We found that in the blood of rabbits of experimental groups recieved sodium sulphate, chromium chloride and chromium citrate, the content of glycoprotein's and their carbohydrate components was significantly higher during the 118 days of the study compared with the control group. Feeding rabbits with mineral supplements likely reflected the differences compared with the control parameters of nonspecific resistance in the blood for the study period, which was more pronounced in the first two months of life.

  9. The Mechanical properties and microstructural relationships in iron--manganese--chromium alloys. [14 to 20% Mn, 13 to 18% Cr, Al and Ti additions

    Energy Technology Data Exchange (ETDEWEB)

    Thompson, L.D.

    1977-01-01

    The relationships between microstructure and mechanical properties were studied for a series of Fe--Mn--Cr alloys. A combination of optical and scanning electron microscopy, EDAX analysis, and x-ray diffractometry was used to characterize the microstructures. Tensile testing and Charpy V-notch impact testing were utilized to study the mechanical properties. Triplex structures of gamma (fcc), alpha (bcc), and epsilon (hcp) were obtained in air-cool and quench-and-refrigeration heat treatments. Increasing volume fractions of metastable austenite and epsilon-martensite phases, which transform during testing, were found to have beneficial effects on the toughness and ductility properties, without significant losses in strength properties. A chromium concentration of 13 percent led to a better combination of strength and ductility than a concentration of 18 percent. The mechanical properties and preliminary corrosion results for the air-cooled 18Mn--13Cr and 16Mn--13Cr alloys are comparable to those of AISI 300 series austenitic stainless steels. These alloys show promise, therefore, as base systems for replacement austenitic stainless alloys. In addition, the 18Mn--13Cr air-cooled alloy exhibits excellent cryogenic properties, i.e., a yield strength of 360 MPa (53 ksi), an ultimate strength of 1110 MPa (161 ksi) an elongation of 60 percent, and a reduction in area of 17 percent at -196/sup 0/C. 62 figures, 9 tables.

  10. The use of trivalent chromium bath to obtain a solar selective black chromium coating

    Science.gov (United States)

    Survilienė, S.; Češūnienė, A.; Juškėnas, R.; Selskienė, A.; Bučinskienė, D.; Kalinauskas, P.; Juškevičius, K.; Jurevičiūtė, I.

    2014-06-01

    Black chromium coatings were electrodeposited from a trivalent chromium bath using a ZnO additive as a second main component. Black chromium was electrodeposited on steel and copper plates and substrates plated with bright nickel prior to black chromium electrodeposition. The black chromium coatings were characterized by XRD and SEM. The XRD data suggest that the phase structure of black chromium may be defined as a zinc solid solution in chromium or a chromium solid solution in zinc depending on the chromium/zinc ratio in the deposit. The role of substrate finish was evaluated through the corrosion resistance and reflectance of black chromium. According to corrosion tests the samples plated with bright nickel prior to black chromium deposition have shown the highest corrosion resistance. The electrodeposited black chromium possesses good optical properties for the absorption of solar energy. The absorption coefficient of black chromium was found to be over 0.99 for the samples obtained without the Ni undercoat and below 0.99 for those obtained with the use of Ni undercoat. However, the use of nickel undercoat before black chromium plating is recommended because it remarkably improves the corrosion resistance of samples.

  11. Groundwater contaminant by hexavalent chromium

    Energy Technology Data Exchange (ETDEWEB)

    Parsons, C. [Univ. of Texas, Austin, TX (United States)

    1995-11-01

    Oxidation of trivalent chromium to hexavalent chromium has been investigated as a function of total manganese in soils as well as various incubation conditions. Chromium and manganese contents were analyzed by atomic absorption (graphite furnace and flame emission respectively) following acid digestion. Total hexavalent chromium generation capacity was determined by addition of 0.001 M CrCL3, incubation, and analysis by s-diphenyl carbazide. Samples were then leached with CaSO{sub 4} and MgSO{sub 4} and incubated in various environments (oven, freeze-drier, field moist, ultrafreeze) to test for geogenic generation of Cr(IV). The degree of geogenic generation of hexavalent chromium was compared with total Mn and Cr content as well as hexavalent generational capacity.

  12. Influence of cobalt and chromium additions on the precipitation processes in a Cu-4Ti alloys; Influencia de la adicion de cobalto y cromo en el proceso de precipitacion en una aleacion de Cu-4Ti

    Energy Technology Data Exchange (ETDEWEB)

    Donoso, E.

    2010-07-01

    The influence of 0.5% atomic cobalt and 1% atomic chromium additions on the precipitation hardening of Cu-4Ti alloy was studied by differential scanning calorimetry (DSC) and microhardness measurements. The analysis of the calorimetric curves, for binary alloy, shows the presence of two overlapping exothermic reactions (stages 1 and 2) attributed to the formation of Cu{sub 4}Ti and Cu{sub 3}Ti particles in the copper matrix, respectively. DSC curves for Cu-4Ti-0.5Co alloy shows three exothermic effects (overlapping stages 3 and 4 and stage 5) associated to the formation of phases Ti{sub 2}Co, TiCo and Cu{sub 4}Ti, respectively. DSC curves for Cu-4Ti1Cr alloy shows three exothermic reactions (stages 6, 7 and 9) and one endothermic peak (stage 8). The exothermic reactions correspond to the formation of phases Cr{sub 2}Ti, Cu{sub 4}Ti and Cu{sub 3}Ti, respectively, and the endothermic reactions are attributed to the Cr{sub 2}Ti dissolution. The activation energies calculated using the modified Kissinger method were lower than the ones corresponding to diffusion of cobalt, chromium, and titanium in copper. Kinetic parameters were obtained by a convolution method based on the Johnson-Mehl-Avrami (JMA) formalism. Microhardness measurements confirmed the formation of the mentioned phases. Also, these measurements confirmed the effect of cobalt and chromium addition on the binary alloy hardness. (Author). 31 refs.

  13. Inoculation of chromium white cast iron

    Directory of Open Access Journals (Sweden)

    D. Kopyciński

    2009-01-01

    Full Text Available It has been proved that an addition of boron carbide introduced as an inoculant to the chromium white cast iron changes the structureof castings. Castings after inoculation revealed a different structure with numerous grains. Primary precipitates of chromium carbide also appeared, reducing the mechanical properties of as-cast parts. Properly established heat treatment regime makes chromium iron castings regain their, originally high, mechanical properties.

  14. 21 CFR 73.1015 - Chromium-cobalt-aluminum oxide.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Chromium-cobalt-aluminum oxide. 73.1015 Section 73... LISTING OF COLOR ADDITIVES EXEMPT FROM CERTIFICATION Drugs § 73.1015 Chromium-cobalt-aluminum oxide. (a) Identity. The color additive chromium-cobalt-aluminum oxide is a blue-green pigment obtained by calcining...

  15. [Bioremediation of chromium (VI) contaminated site by reduction and microbial stabilization of chromium].

    Science.gov (United States)

    Zheng, Jia-Chuan; Zhang, Jian-Rong; Liu, Xi-Wen; Xu, Qian; Shi, Wei-Lin

    2014-10-01

    Chromium (VI) contaminated soil samples were collected from a chemical plant in Suzhou. Firstly, the reduced soil was prepared by adding reagent (Stone-sulfure reagent) into polluted soil to transfer most chromium (VI) into chromium (III), then a nutrient solution was introduced into the reduced soil, and the stabilized soil was obtained after 60 days culturing. The chromium (VI) content of the three kinds of soil was analyzed. The results showed that the chromium (VI) content in toxicity characteristic leaching liquid (TCLL) dropped by 96. 8% (from 8.26 mg · L(-1) to 0.26 mg · L(-1)), and the total chromium content dropped by 95.7% (from 14.66 mg · L(-1) to 0.63 mg · L(-1)) after bioremediation in 5% nutrient solution. Additionally, the durability of chromium stabilization was tested by potassium permanganate oxidation and sterilization of microbe-treated soil. After oxidation, the chromium (VI) content in TCLL of the reduced soil was increased from 8.26 mg · L(-1) to 14.68 mg · L(-1). However, the content after bioremediation was decreased to 2.68 mg · L(-1). The results of sterilization demonstrated that the death of microbe had no significant effect on the stabilization of chromium. Consequently, the research in this paper demonstrated the feasibility of bioremediation of chromium (VI) polluted soil through reduction followed by stabilization/soilidification, and provided a technique with low cost but high efficiency.

  16. Chromium in diet

    Science.gov (United States)

    The best source of chromium is brewer's yeast. However, many people do not use brewer's yeast because it causes bloating ( abdominal distention ) and nausea . Other good sources of chromium include ...

  17. Chromium Salen Mediated Alkene Epoxidation

    DEFF Research Database (Denmark)

    Petersen, Kaare Brandt; Norrby, Per-Ola; Daly, Adrian M.;

    2002-01-01

    The mechanism of alkene epoxidation by chromium(v) oxo salen complexes has been studied by DFT and experimental methods. The reaction is compared to the closely related Mn-catalyzed process in an attempt to understand the dramatic difference in selectivity between the two systems. Overall......, the studies show that the reactions have many similarities, but also a few critical differences. In agreement with experiment, the chromium system requires a change from low- to high-spin in the catalytic cycle, whereas the manganese system can proceed either with spin inversion or entirely on the high......-spin surface. The low-spin addition of metal oxo species to an alkene leads to an intermediate which forms epoxide either with a barrier on the low-spin surface or without a barrier after spin inversion. Supporting evidence for this intermediate was obtained by using vinylcyclopropane traps. The chromium...

  18. Heterogeneous chromium catalysts

    NARCIS (Netherlands)

    2005-01-01

    The present invention relates to a heterogeneous chromium catalyst system for the polymerisation of ethylene and/or alpha olefins prepared by the steps of: (a) providing a silica-containing support, (b) treating the silica-containing support with a chromium compound to form a chromium-based silica-c

  19. REINFORCEMENT OF NICKEL CHROMIUM ALLOYS WITH SAPPHIRE WHISKERS.

    Science.gov (United States)

    SAPPHIRE, COMPOSITE MATERIALS, CERAMIC FIBERS , CERAMIC FIBERS , TITANIUM COMPOUNDS, ZIRCONIUM COMPOUNDS, HYDRIDES, ADDITIVES, CHROMIUM ALLOYS, FIBER METALLURGY, IRON COMPOUNDS, ENCAPSULATION, DENSITY, SURFACE TENSION.

  20. Effect the addition of 10% (volume fraction) chromium on the mechanical properties of NiAlCr processed by powder metallurgy; Efecto de la adicion de un 10% en volumen de cromo en el comportamiento a traccion de aleaciones pulvimetalurgicas NiAlCr

    Energy Technology Data Exchange (ETDEWEB)

    Garcia-Barriocanal, J.; Garces, G.; Perez, P.; Adeva, P.

    2005-07-01

    The mechanical properties of Ni{sub 3}Al-Cr reinforced with 10% in volume fraction of chromium particles produced by powder metallurgy have been studied. For this purpose, milled powders with composition of Ni-20.9Al-8Cr-0.49B (% st.) with and without the addition of 10% in volume fraction of chromium particles have been produced. Both alloys were consolidated by hot isostatic pressing (HIP). After HIP, heat treatment was applied to homogenize the microstructure. The chromium reinforcement has an important effect in the yield strength and ultimate strength increase. The reinforced alloy presents a yield strength of 1300 MPa at room temperature with respect to 800 MPa for the un-reinforced material. After heat treatment, the yield strength of both alloys does not change significantly. However, a decrease in ductility and ultimate tensile strength have been observed. (Author) 4 refs.

  1. 21 CFR 73.3110a - Chromium-cobalt-aluminum oxide.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Chromium-cobalt-aluminum oxide. 73.3110a Section... LISTING OF COLOR ADDITIVES EXEMPT FROM CERTIFICATION Medical Devices § 73.3110a Chromium-cobalt-aluminum oxide. (a) Identity. The color additive chromium-cobalt-aluminum oxide (Pigment Blue 36) (CAS Reg....

  2. Tribological Characteristics of Chromium-active Carbon Electroplated Composite Coatings

    Institute of Scientific and Technical Information of China (English)

    GUKa-fi; HUAMeng; Yi-min

    2004-01-01

    A process of chromium electroplating using a standard bath with additives and active carbon particles was reported, and the tribological behaviors of the composite coatings using the pin-on-disk tester and the table wear tester were i nvestig(aed. Experimental results indicate that the electroplated chromium-active carbon composite coatings exhibited the low friction coefficient anti excellent anti-wear properties whets coffered with the normal chromium electroplated ones. The formation of active carbon particles within the chromium matrices can be explained by SEM analysis and the mechanis of wear resistance of the composite coatings were studied.

  3. Chromium recycling of tannery waste through microbial fermentation.

    Science.gov (United States)

    Katsifas, E A; Giannoutsou, E; Lambraki, M; Barla, M; Karagouni, A D

    2004-02-01

    An Aspergillus carbonarius isolate, selected from an established microbial culture collection, was used to study the biodegradation of chromium shavings in solid-state fermentation experiments. Approximately 97% liquefaction of the tannery waste was achieved and the liquid obtained from long-term experiments was used to recover chromium. The resulting alkaline chromium sulfate solution was useful in tanning procedures. A proteinaceous liquid was also obtained which has potential applications as a fertilizer or animal feed additive and has several other industrial uses. The A. carbonarius strain proved to be a very useful tool in tannery waste-treatment processes and chromium recovery in the tanning industries.

  4. Influence of Chelating Agents on Chromium Fate in Sediment

    Institute of Scientific and Technical Information of China (English)

    WANGXIAOCHANG; SUNJINHE; 等

    1996-01-01

    A laboratory investigation on reaction between chelating agents and chromium was conducted to evaluate the effect of chelating agents on the adsorption and desorption of chromium in sediment.The amount of adsorbed chromium(VI) in sediment decreased slightly by 5%-10% because of addition of chelating agents.Chelating agents inhibited the removal of Cr(Ⅲ)by sediment from solutions and the inhibiting effect was in the order:citric acid>tartaric acid>EDTA,Salicylic acid.No effect of chelating agents on desorption of chromium in sediment was observed.

  5. Scientific Opinion on ChromoPrecise® cellular bound chromium yeast added for nutritional purposes as a source of chromium in food supplements and the bioavailability of chromium from this source

    Directory of Open Access Journals (Sweden)

    EFSA Panel on Food Additives and Nutrient Sources added to Food (ANS

    2012-11-01

    Full Text Available The Panel on Food Additives and Nutrient Sources added to Food (ANS provides a scientific opinion re-evaluating the safety of ChromoPrecise® cellular bound chromium yeast added for nutritional purposes as a source of chromium in food supplements and the bioavailability of chromium from this source. ChromoPrecise® is a yeast preparation with an enriched trivalent chromium content, obtained by culture of Saccharomyces cerevisiae in the presence of chromium chloride. A daily intake of 100 µg chromium(III. There are limited data on the nature and identity of the organic chromium(III compounds contained in chromium-enriched yeast and on their toxicokinetic and toxicodynamic behaviour in the body. Overall, the Panel concluded that the bioavailability in man of chromium from chromium-enriched yeast is potentially up to approximately ten times higher than that of chromium from chromium chloride. A NOAEL of 2500 mg/kg bw/day ChromoPrecise® was identified in a 90-day feeding study in rats; no evidence of adverse effects of chromium yeasts were reported in other animal studies investigating the effects of dietary supplementation with chromium yeast. ChromoPrecise® chromium yeast was non-genotoxic in a range of in vitro genotoxicity studies. Although no information was available on the chronic toxicity, carcinogenicity or reproductive toxicity of ChromoPrecise® chromium yeast, the ANS Panel has previously concluded that trivalent chromium is not carcinogenic, and limited data on other chromium yeasts provide no evidence of an effect on reproductive endpoints. No adverse effects have been reported in clinical efficacy trials with chromium yeasts. The Panel concluded that the use of ChromoPrecise® chromium yeast in food supplements is not of concern, despite the lack of data on the nature and identity of the organic chromium(III compounds contained in the product, provided that the intake does not exceed 250 μg/day, as recommended by the WHO.

  6. Investigations on the fracture toughness of austempered ductile iron alloyed with chromium

    Energy Technology Data Exchange (ETDEWEB)

    Rao, P. Prasad; Putatunda, Susil K

    2003-04-15

    An investigation was carried out to examine the influence of chromium content on the plane strain fracture toughness of austempered ductile iron (ADI). ADIs containing 0, 0.3 and 0.5 wt.% chromium were austempered over a range of temperatures to produce different microstructures. The microstructures were characterized by optical microscopy and X-ray diffraction. Plane strain fracture toughness of all these materials was determined and correlated with microstructure and chromium content. The chromium content was found to influence the fracture toughness through its influence on the processing window. Since the chromium addition shifts the processing window to shorter durations, the higher chromium alloys at higher austempering temperatures tend to fall outside of the processing window, resulting in less than optimum microstructure and inferior fracture toughness. A small chromium addition of 0.3 wt.% was found to be beneficial for the fracture toughness of ADI.

  7. Stabilization of chromium salt in ordinary portland cement

    Indian Academy of Sciences (India)

    Damir Barbir; Pero Dabić; Petar Krolo

    2012-12-01

    Ordinary Portland cement (OPC) samples containing the chromium salt have been investigated using differential microcalorimetry, conductometry and Fourier transform infrared spectroscopic analysis. The effect of chromium on OPC hydration was evaluated by continuous observing of early hydration. The microcalorimetrical results show that with increasing the share of chromium salt, heat maximums assume lower values and the occurrence of the maximum registered in the earlier hydration times. Conductometrical measurements show that with increasing addition of chromium salt, curve did not show any specific shape, immediate drop in specific conductivity is noticed and the maximum is reached earlier. This coincides with microcalorimetrical results. It can be concluded that the addition of chromium does not affect the mechanism of the hydration process, but it does affect the kinetic parameters and dynamics of the cement hydration process. It was found that chromium salt addition to the cement–water system is acceptable up to 2 wt.%. According to standard EN 196-3 for OPC, the beginning of binding time should occur after 60 minutes. Increased amount of chromium over 2 wt.% significantly accelerate the beginning of binding time and for the system it is not acceptable.

  8. Preparation and Characterization of Plasma-Sprayed Ultrafine Chromium Oxide Coatings

    Institute of Scientific and Technical Information of China (English)

    LIN Feng; JIANG Xianliang; YU Yueguang; ZENG Keli; REN Xianjing; LI Zhenduo

    2007-01-01

    Ultrafine chromium oxide coatings were prepared by plasma spraying with ultrafine feedstock. Processing parameters of plasma spraying were optimized. Optical microscope (OM) was used to observe the microstructure of the ultrafine chromium oxide coatings. Scanning electron microscopy (SEM) was used to observe the morphology and particle size of ultrafine powder feedstock as well as to examine the microstructure of the chromium oxide coating. In addition, hardness and bonding strength of the ultrafine chromium oxide coatings were measured.The results showed that the optimized plasma spraying parameters were suitable for ultrafine chromium oxide coating and the properties and microstructure of the optimized ultrafine chromium oxide coating were superior compared to conventional chromium oxide wear resistant coatings.

  9. Femtosecond laser surface structuring and oxidation of chromium thin coatings: Black chromium

    Energy Technology Data Exchange (ETDEWEB)

    Kotsedi, L., E-mail: Kotsedi@tlabs.ac.za [UNESCO-UNISA Africa Chair in Nanosciences-Nanotechnology, College of Graduate Studies, University of South Africa, Muckleneuk Ridge, P.O. Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, Somerset West 7129, P.O. Box 722, Somerset West, Western Cape (South Africa); Nuru, Z.Y. [UNESCO-UNISA Africa Chair in Nanosciences-Nanotechnology, College of Graduate Studies, University of South Africa, Muckleneuk Ridge, P.O. Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, Somerset West 7129, P.O. Box 722, Somerset West, Western Cape (South Africa); Mthunzi, P. [National Laser Centre, Council for Scientific and Industrial Research, 0001 Pretoria (South Africa); Muller, T.F.G. [University of the Western Cape, Physics Department, Bellville, 7535 Cape Town (South Africa); Eaton, S.M. [Physics Department, Politecnico di Milano, Piazza Leonardo Da Vinci, 32, 20133 Milano (Italy); Julies, B. [University of the Western Cape, Physics Department, Bellville, 7535 Cape Town (South Africa); Manikandan, E. [UNESCO-UNISA Africa Chair in Nanosciences-Nanotechnology, College of Graduate Studies, University of South Africa, Muckleneuk Ridge, P.O. Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, Somerset West 7129, P.O. Box 722, Somerset West, Western Cape (South Africa); Ramponi, R. [Physics Department, Politecnico di Milano, Piazza Leonardo Da Vinci, 32, 20133 Milano (Italy); Maaza, M. [UNESCO-UNISA Africa Chair in Nanosciences-Nanotechnology, College of Graduate Studies, University of South Africa, Muckleneuk Ridge, P.O. Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, Somerset West 7129, P.O. Box 722, Somerset West, Western Cape (South Africa)

    2014-12-01

    Highlights: • Oxidation of the chromium thin film to chromium oxide by femtosecond laser with a fundamental wavelength of 1064 nm. • Solar absorber from chromium oxide that low percentage reflectance. • Femtosecond laser oxidation, with a de-focused laser. • Chromium oxide formation by femtosecond laser in normal ambient. - Abstract: In view of their potential applications as selective solar absorbers, chromium coatings on float glass substrates were nano/micro structured by femtosecond laser in air. Raman and X-rays diffraction investigations confirmed the formation of an ultra-porous α-Cr{sub 2}O{sub 3} layer at the surface; higher is the input laser power, enhanced is the crystallinity of the α-Cr{sub 2}O{sub 3} layer. The α-Cr{sub 2}O{sub 3} layer with the Cr underneath it in addition to the photo-induced porosity acted as a classical ceramic–metal nano-composite making the reflectance to decrease significantly within the spectral range of 190–1100 nm. The average reflectance decreased from 70 to 2%.

  10. Production of basic chromium sulfate by using recovered chromium from ashes of thermally treated leather.

    Science.gov (United States)

    Dettmer, Aline; Nunes, Keila Guerra Pacheco; Gutterres, Mariliz; Marcílio, Nilson Romeu

    2010-04-15

    Leather wastes tanned with chromium are generated during the production process of leather, hence the wastes from hand crafted goods and footwear industries are a serious environmental problem. The thermal treatment of leather wastes can be one of the treatment options because the wastes are rich in chromium and can be used as a raw material for sodium chromate production and further to obtain several chromium compounds. The objective of this study was to utilize the chromium from leather wastes via basic chromium sulfate production to be subsequently applied in a hide tanning. The obtained results have shown that this is the first successful attempt to achieve desired base properties of the product. The result was achieved when the following conditions were applied: a molar ratio between sodium sulfite and sodium dichromate equal to 6; reaction time equal to 5 min before addition of sulfuric acid; pH of sodium dichromate solution equal to 2. Summarizing, there is an opportunity to utilize the dangerous wastes and reused them in the production scheme by minimizing or annulling the environmental impact and to attend a sustainable process development concept.

  11. New technology for comprehensive utilization of aluminum-chromium residue from chromium salts production

    Institute of Scientific and Technical Information of China (English)

    LI Xiao-bin; QI Tian-gui; JIANG Xin-min; ZHOU Qiu-sheng; LIU Gui-hua; PENG Zhi-hong; HAN Deng-lun; ZHANG Zhong-yuan; YANG Kun-shan

    2008-01-01

    Colloidal aluminum-chromium residue(ACR) was mass-produced in chromate production process, and the large energy consumption and high recovery cost existed in traditional methods of utilizing such ACR. To overcome those problems, a new comprehensive method was proposed to deal with the ACR, and was proven valid in industry. In the new process, the chromate was separated firstly from the colloidal ACR by ripening and washing with additives, by which more than 95% hexavalent chromium was recovered. The chromium-free aluminum residue(CFAR), after properly dispersed, was digested at 120-130 ℃ and more than 90% alumina can be recovered. And then the pregnant aluminate solution obtained from digestion was seeded to precipitate aluminum hydroxide. This new method can successfully recover both alumina and sodium chromate, and thus realize the comprehensive utilization of ACR from chromate industry.

  12. Determination of Chromium(III) Picolinate Using High Performance Liquid Chromatography-Ultraviolet Spectrophotometry

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sung Il; Woo, Dong Jin; Kang, Dae Kyung [EASY BIO System, Inc, Chonan (Korea, Republic of); Lee, Myung Hee [Pollin, Inc, Seoul (Korea, Republic of); Woo, Gun Jo [Korea Food and Drug Administration, Seoul (Korea, Republic of); Cha, Ki Won [Inha University, Incheon (Korea, Republic of)

    2003-10-15

    Cr-(pic){sub 3} has been widely used as food additives, drugs, and feed additives. Accordingly, its determination method should be established. In the present paper, we have studied the determination method of chromium(III) picolinate accurately using ESI-MS on-lined with HPLC. Chromium(III) picolinate in feed products was determined successfully. Chromium(III) is very well known as an essential mineral. It is suggested as a cofactor in the maintenance of both normal lipid and carbohydrate metabolism by assisting the action of insulin on a cell membrane. According to the National Research Council, the daily recommended intake of chromium(III) is 50-200 μg. Several organic chromium(III) complexes have been reported to have significantly higher absorption and tissue incorporation activity than inorganic salts such as chromium(III) chloride.

  13. Suppression of interference in the AAS determination of chromium by use of ammonium bifluoride.

    Science.gov (United States)

    Purushottam, A; Naidu, P P; Lal, S S

    1973-07-01

    Addition of 1% of ammonium bifluoride successfully suppresses interference by diverse ions in the atomic-absorption determination of chromium(VI). If the sample solutions also contain chromium(III) addition of 1% of ammonium bifluoride and 0.2% of sodium sulphate is recommended for the suppression.

  14. Finished leather waste chromium acid extraction and anaerobic biodegradation of the products.

    Science.gov (United States)

    Ferreira, Maria J; Almeida, Manuel F; Pinho, Sílvia C; Santos, Isabel C

    2010-06-01

    Due to the amounts of chromium in the leachate resulting from leather leaching tests, chromium sulfate tanned leather wastes are very often considered hazardous wastes. To overcome this problem, one option could be recovering the chromium and, consequently, lowering its content in the leather scrap. With this objective, chromium leather scrap was leached with sulfuric acid solutions at low temperature also aiming at maximizing chromium removal with minimum attack of the leather matrix. The effects of leather scrap dimension, sulfuric acid and sodium sulfate concentration in the solutions, as well as extraction time and temperature on chromium recovery were studied, and, additionally, organic matrix degradation was evaluated. The best conditions found for chromium recovery were leather scrap conditioning using 25mL of concentrated H(2)SO(4)/L solution at 293 or 313K during 3 or 6days. Under such conditions, 30-60+/-5% of chromium was recovered and as low as 3-6+/-1% of the leather total organic carbon (TOC) was dissolved. Using such treatment, the leather scrap area and volume are reduced and the residue is a more brittle material showing enhanced anaerobic biodegradability. Although good recovery results were achieved, due to the fact that the amount of chromium in eluate exceeded the threshold value this waste was still hazardous. Thus, it needs to be methodically washed in order to remove all the chromium de-linked from collagen.

  15. On texture formation of chromium electrodeposits

    DEFF Research Database (Denmark)

    Nielsen, Christian Bergenstof; Leisner, Peter; Horsewell, Andy

    1998-01-01

    The microstructure, texture and hardness of electrodeposited hard, direct current (DC) chromium and pulsed reversed chromium has been investigated. These investigations suggest that the growth and texture of hard chromium is controlled by inhibition processes and reactions. Further, it has been...... established that codeposition of Cr2O3 nanoparticles is a general feature of DC chromium electrodeposition....

  16. The regeneration and recycle of chromium etching solutions using concentrator cell membrane technology.

    Science.gov (United States)

    Chaudhary, Abdul J; Ganguli, Bijita; Grimes, Susan M

    2006-02-01

    The regeneration of chromium (VI) and the recovery of etched copper from chromium etching solutions by electrodialysis is improved by the addition of a concentrator cell in the catholyte chamber. The concentrator media used are ion-exchange resins or activated carbon cloth. The maximum percentages for the regeneration of chromium and recovery of copper in these systems is however less than 80% and 90% respectively because of the competition between the processes of oxidation of Cr(III) and electrodeposition of copper. A novel combination of electrolysis with electrodialysis and concentrator cell technology is developed that achieves 92% chromium regeneration and 90% copper recovery.

  17. Fluoridation of gaseous phase chlorinated hydrocarbons in presence of chromium oxide-based catalysts. Effect of doping substance addition; Fluoration d'hydrocarbures chlores en phase gazeuse en presence de catalyseurs a base d'oxyde de chrome. Effet de l'ajout de dopant

    Energy Technology Data Exchange (ETDEWEB)

    Loustaunau, A.

    2003-11-01

    The preparation of various hydro-fluorocarbons (HFC), like CF{sub 3}CH{sub 2}F, CF{sub 3}CHF{sub 2} and CH{sub 2}F{sub 2}, has been studied at temperatures of 380 deg. C and 250 deg. C in gaseous phase by catalytic fluoridation of the corresponding chlorinated hydrocarbons. The addition of doping substances like zinc, nickel or magnesium to fluorinated alumina supported chromium oxide-based catalysts, has been particularly examined in order to favour the main fluoridation reaction (by simple Cl/F exchange) with respect to secondary reactions (de-hydro-fluoridation and Deacon). Only the addition of small amounts of Zn (Zn/(Zn+Cr) = 0.15) allows to promote the fluoridation reaction and to inhibit the secondary reactions. This effect is enhanced when the molecule is less reactive and when the quantity of matter at the surface of the fluorinated alumina is low. Therefore, the promoting effect is more important in presence of CF{sub 3}CH{sub 2}Cl than in presence of CF{sub 3}CHCl{sub 2} and CH{sub 2}Cl{sub 2}. This positive effect of zinc may result from the formation of a mixed ZnCr{sub 2}O{sub 4} phase during the preparation of the catalyst (evidenced by X-ray photoelectron spectroscopy (XPS)) which may have modified the chemical properties of chromium atoms. Moreover, the XPS and electron microscopy characterizations indicate that the presence of zinc (contrary to nickel and magnesium) may allow a better dispersion of the active chromium atoms for Cl/F exchanges after fluoridation of the catalyst. Those may correspond to the presence of very fluorinated species, like 'Cr-F', and oxi-fluorinated like 'CrOF'. Thus, in the presence of a small amount of metals at the surface of the support, the formation of these different species is favoured. (J.S.)

  18. Reduction of tetravalent chromium induced optical loss in Nd:Cr:GSGG

    Energy Technology Data Exchange (ETDEWEB)

    Pertica, A.J.; Marion, J.E.; Stokowski, S.E. (Lawrence Livermore National Laboratory, Livermore, CA 94550 (US))

    1989-10-20

    We report on methods for eliminating of optical absorption in neodymium, chromium doped gadolinium scandium gallium garnet (Nd;Cr:GSGG) due to tetravalent chromium at the laser wavelength. These methods include doping of the crystal melt with specific additive as well as post growth heat treatments.

  19. CHROMIUM STATUS IN DIABETES MELLITUS

    Directory of Open Access Journals (Sweden)

    Keshavarz

    1996-06-01

    Full Text Available Fasting serum chromium, total cholesterol HDL-cholesterol, LDL-cholesterol, triacytglycerot and blood sugar were determined in fifty two diabetic patients with no other organic diseases anil compared with those obtained from a control group including fourty two healthy volunteers matched for age, sex ami body mass irutex (BMI. Fasting serum chromium and HDL-cholesterol were significantly lower in patients than in controls (p<0.0001 and p<0.001 respectively, but the mean triacytglycerot concentration was significantly higher in patients than in controls (p<002. Mean total cholesterol and LDL-cholesterol values were not significantly different in the two groups. Mean intake of energy, proteins, fats and chromium, estimated by the 24 hr dietary recall method were not significantly different in the two groups. We demonstrated that despite an adequate intake of chromium, the fasting serum chromium was lower in diabetic patients than in control subjects. Chromium deficiency in diabetic patients may act as a contributing factor in aggravating the disease's complications.

  20. Galvanic cells including cobalt-chromium alloys.

    Science.gov (United States)

    Gjerdet, N R

    1980-01-01

    Galvanic cells may be created when dentures made of cobalt-chromium alloys are placed on teeth with metallic restorations. The power of such cells was evaluated in an in vitro galvanic using amalgams, gold alloy, and nickel-chromium alloys. The amalgams and one of the nickel-chromium alloys revealed high corrosion currents when placed in contact with cobalt-chromium alloy, the conventional amalgam showing the highest values. The gold alloy and another nickel-chromium alloy exhibited low corrosion currents and they were noble with respect to cobalt-chromium.

  1. Oxidation resistant, thoria-dispersed nickel-chromium-aluminum alloy

    Science.gov (United States)

    Baranow, S.; Klingler, L. J.

    1973-01-01

    Modified thoria-dispersed nickel-chromium alloy has been developed that exhibits greatly improved resistance to high-temperature oxidation. Additions of aluminum have been made to change nature of protective oxide scale entirely and to essentially inhibit oxidation at temperatures up to 1260 C.

  2. Chromium at High Pressure

    Science.gov (United States)

    Jaramillo, Rafael

    2012-02-01

    Chromium has long served as the archetype of spin density wave magnetism. Recently, Jaramillo and collaborators have shown that Cr also serves as an archetype of magnetic quantum criticality. Using a combination of x-ray diffraction and electrical transport measurements at high pressures and cryogenic temperatures in a diamond anvil cell, they have demonstrated that the N'eel transition (TN) can be continuously suppressed to zero, with no sign of a concurrent structural transition. The order parameter undergoes a broad regime of exponential suppression, consistent with the weak coupling paradigm, before deviating from a BCS-like ground state within a narrow but accessible quantum critical regime. The quantum criticality is characterized by mean field scaling of TN and non mean field scaling of the transport coefficients, which points to a fluctuation-induced reconstruction of the critical Fermi surface. A comparison between pressure and chemical doping as means to suppress TN sheds light on different routes to the quantum critical point and the relevance of Fermi surface nesting and disorder at this quantum phase transition. The work by Jaramillo et al. is broadly relevant to the study of magnetic quantum criticality in a physically pure and theoretically tractable system that balances elements of weak and strong coupling. [4pt] [1] R. Jaramillo, Y. Feng, J. Wang & T. F. Rosenbaum. Signatures of quantum criticality in pure Cr at high pressure. Proc. Natl. Acad. Sci. USA 107, 13631 (2010). [0pt] [2] R. Jaramillo, Y. Feng, J. C. Lang, Z. Islam, G. Srajer, P. B. Littlewood, D. B. McWhan & T. F. Rosenbaum. Breakdown of the Bardeen-Cooper-Schrieffer ground state at a quantum phase transition. Nature 459, 405 (2009).

  3. Environmental biochemistry of chromium.

    Science.gov (United States)

    Losi, M E; Amrhein, C; Frankenberger, W T

    1994-01-01

    Chromium is a d-block transitional element with many industrial uses. It occurs naturally in various crustal materials and is discharged to the environment as industrial waste. Although it can occur in a number of oxidation states, only 3+ and 6+ are found in environmental systems. The environmental behavior of Cr is largely a function of its oxidation state. Hexavalent Cr compounds (mainly chromates and dichromates) are considered toxic to a variety of terrestrial and aquatic organisms and are mobile in soil/water systems, much more so than trivalent Cr compounds. This is largely because of differing chemical properties: Hexavalent Cr compounds are strong oxidizers and highly soluble, while trivalent Cr compounds tend to form relatively inert precipitates at near-neutral pH. The trivalent state is generally considered to be the stable form in equilibrium with most soil/water systems. A diagram of the Cr cycle in soils and water is given in Fig. 6 (Bartlett 1991). This illustration provides a summary of environmentally relevant reactions. Beginning with hexavalent Cr that is released into the environment as industrial waste, there are a number of possible fates, including pollution of soil and surface water and leaching into groundwater, where it may remain stable and, in turn, can be taken up by plants or animals, and adsorption/precipitation, involving soil colloids and/or organic matter. Herein lies much of the environmental concern associated with the hexavalent form. A portion of the Cr(VI) will be reduced to the trivalent form by inorganic electron donors, such as Fe2+ and S2-, or by bioprocesses involving organic matter. Following this conversion, Cr3+ can be expected to precipitate as oxides and hydroxides or to form complexes with numerous ligands. This fraction includes a vast majority of global Cr reserves. Soluble Cr3+ complexes, such as those formed with citrate, can undergo oxidation when they come in contact with manganese dioxide, thus reforming

  4. Chromium behavior during cement-production processes: A clinkerization, hydration, and leaching study

    Energy Technology Data Exchange (ETDEWEB)

    Sinyoung, Suthatip [Department of Environmental Engineering, Faculty of Engineering, King Mongkut' s University of Technology Thonburi, Bangkok, 10140 (Thailand); Songsiriritthigul, Prayoon [Synchrotron Light Research Institute, PO Box 93 Nakhon Ratchasima, 30000 (Thailand); School of Physics, Suranaree University of Technology, Nakhon Ratchasima, 30000 (Thailand); Asavapisit, Suwimol, E-mail: suwimol_s@hotmail.com [Environmental Technology, School of Energy and Materials, King Mongkut' s University of Technology Thonburi, Bangkok, 10140 (Thailand); National Center of Excellence for Environmental and Hazardous Waste Management, Faculty of Engineering, King Mongkut' s University of Technology Thonburi, Bangkok, 10140 (Thailand); Kajitvichyanukul, Puangrat, E-mail: puangratk@nu.ac.th [National Center of Excellence for Environmental and Hazardous Waste Management, Faculty of Engineering, King Mongkut' s University of Technology Thonburi, Bangkok, 10140 (Thailand); Department of Civil Engineering, Faculty of Engineering, Naresuan University, Phitsanulok, 65000 (Thailand)

    2011-07-15

    Highlights: {yields} Behavior of chromium during cement-production processes. {yields} Formation of new chromium compounds in clinker with chromium oxidation states of +3, +4.6, +5, and +6. {yields} Addition of chromium altered the composition of the clinker phases, setting time, and compressive strength of hydrated mixes. {yields} Cr{sup 3+} and Cr{sup 6} were leached during leaching tests, whereas other species remained in the mortar. - Abstract: The behavior of chromium during the production of cement clinker, during the hydration of cement and during the leaching of cement mortars was investigated. The microstructures of clinker and mortar properties were investigated using free lime, XRD, SEM/EDS, and TG/DTA techniques. Chromium was found to be incorporated in the clinker phase. The formation of new chromium compounds such as Ca{sub 6}Al{sub 4}Cr{sub 2}O{sub 15}, Ca{sub 5}Cr{sub 3}O{sub 12}, Ca{sub 5}Cr{sub 2}SiO{sub 12}, and CaCr{sub 2}O{sub 7}, with chromium oxidation states of +3, +4.6, +5, and +6, respectively, was detected. After the hydration process, additional chromium compounds were identified in the mortar matrix, including Ca{sub 5}(CrO{sub 4}){sub 3}OH, CaCrO{sub 4}.2H{sub 2}O, and Al{sub 2}(OH){sub 4}CrO{sub 4}, with chromium oxidation states of +4.6, +6, and +6, respectively. Additionally, some species of chromium, such as Cr{sup 3+} from Ca{sub 6}Al{sub 4}Cr{sub 2}O{sub 15} and Cr{sup 6+} from CaCr{sub 2}O{sub 7}, CaCrO{sub 4}.2H{sub 2}O, and Al{sub 2}(OH){sub 4}CrO{sub 4}, were leached during leaching tests, whereas other species remained in the mortar. The concentrations of chromium that leached from the mortar following U.S. EPA Method 1311 and EA NEN 7375:2004 leaching tests were higher than limits set by the U.S. EPA and the Environment Agency of England and Wales related to hazardous waste disposal in landfills. Thus, waste containing chromium should not be allowed to mix with raw materials in the cement manufacturing process.

  5. Chromium behavior during cement-production processes: a clinkerization, hydration, and leaching study.

    Science.gov (United States)

    Sinyoung, Suthatip; Songsiriritthigul, Prayoon; Asavapisit, Suwimol; Kajitvichyanukul, Puangrat

    2011-07-15

    The behavior of chromium during the production of cement clinker, during the hydration of cement and during the leaching of cement mortars was investigated. The microstructures of clinker and mortar properties were investigated using free lime, XRD, SEM/EDS, and TG/DTA techniques. Chromium was found to be incorporated in the clinker phase. The formation of new chromium compounds such as Ca(6)Al(4)Cr(2)O(15), Ca(5)Cr(3)O(12), Ca(5)Cr(2)SiO(12), and CaCr(2)O(7), with chromium oxidation states of +3, +4.6, +5, and +6, respectively, was detected. After the hydration process, additional chromium compounds were identified in the mortar matrix, including Ca(5)(CrO(4))(3)OH, CaCrO(4)·2H(2)O, and Al(2)(OH)(4)CrO(4), with chromium oxidation states of +4.6, +6, and +6, respectively. Additionally, some species of chromium, such as Cr(3+) from Ca(6)Al(4)Cr(2)O(15) and Cr(6+) from CaCr(2)O(7), CaCrO(4)·2H(2)O, and Al(2)(OH)(4)CrO(4), were leached during leaching tests, whereas other species remained in the mortar. The concentrations of chromium that leached from the mortar following U.S. EPA Method 1311 and EA NEN 7375:2004 leaching tests were higher than limits set by the U.S. EPA and the Environment Agency of England and Wales related to hazardous waste disposal in landfills. Thus, waste containing chromium should not be allowed to mix with raw materials in the cement manufacturing process.

  6. RESEARCH AND APPLICATION OF AS-CAST WEAR RESISTANCE HIGH CHROMIUM CAST IRON

    Institute of Scientific and Technical Information of China (English)

    1998-01-01

    The influence of alloy elements, such as boron and silicon, on the microstructure and properties of as-cast high chromium cast iron is studied. The results show that boron and silicon have a great effect on the mechanical properties and the wear resistance. Through proper addition of boron and silicon, the properties of as-cast high chromium cast iron can be improved effectively. Through analyzing the distribution of elements by scanning electron microscope, it has been shown that the addition of boron and silicon lowers the mass fraction of chromium saturated in as-cast austenite, and makes it unstable and liable to be transformed into martensite. The as-cast high chromium cast iron with proper content of boron and silicon is suitable for the manufacture of lining for asphalt concrete mixer and its wear resistance is 14 times that of lining made of low alloy white cast iron.

  7. Intestinal absorption of chromium as affected by wheat bran

    Energy Technology Data Exchange (ETDEWEB)

    Keim, K.S.; Holloway, C.L.; Hegsted, M.

    1986-03-01

    This study was designed to investigate the influence of dietary fiber, as found in wheat bran, on the absorption of chromium. Twenty male Sprague-Dawley rats were divided into two groups of 10. The control was fed a semi-purified diet containing casein, methionine, cornstarch, sucrose, corn oil, mineral and vitamin mix, and choline bitartrate. The experimental group was fed the same diet but with soft red winter wheat bran added to a level of 35% of the diet at the expense of sucrose. To determine chromium absorption and uptake by selected tissues, rats were fasted for 24 hr, fed 5 g of the respective diet, 2 hr later intubated with 100..mu..Ci of Cr-51of sacrificed 24 hr later. The rats wee housed in metabolic cages after the Cr-51 intubation. The addition of wheat brand to the diet did not significantly affect chromium absorption as measured by percent dose of Cr-51 in the 24 hr urine. The percent dose in the control group was 0.68 +/- 0.20% (mean +/- SEM) and in the experimental group 0.63 +/- 0.24% (mean +/-SEM) (N.S.). The cr-51 uptake of liver, spleen, jejunum, and blood was not statistically different between groups. These results indicate that dietary fiber as found in wheat bran does not impair intestinal absorption of chromium.

  8. Simultaneous determination of chromium(III) and chromium(VI) in aqueous solutions by ion chromatography and chemiluminescence detection

    DEFF Research Database (Denmark)

    Gammelgaard, Bente; Jøns, O; Nielsen, B

    1992-01-01

    A method for the simultaneous determination of chromium(iii) and chromium(vi) in a flow system based on chemiluminescence was developed. A Dionex cation-exchange guard column was used to separate chromium(iii) from chromium(vi), and chromium(vi) was reduced by potassium sulfite, whereupon both...

  9. Reduction of chromium (VI by the indirect action of Thiobacillus thioparus

    Directory of Open Access Journals (Sweden)

    E. Donati

    2003-03-01

    Full Text Available The microbial reduction of chromium(VI to chromium(III has been one of the most widely studied forms of metal bioremediation. Recently, we have found that Thiobacillus ferrooxidans and Thiobacillus thiooxidans, growing on elemental sulphur, can indirectly promote chromium(VI reduction by producing reducing agents such as sulphite and thiosulphate, which abiotically reduce chromium(VI. Those species of Thiobacillus are acidophilic bacteria which grow optimally at pH values lower than 4. However, most of those reducing agents are stabilised at higher pH values. Thus, the present paper reports on the ability to reduce chromium(VI using another specie of Thiobacilli, Thiobacillus thioparus, which is able to grow at pH close to 7.0. T. thioparus cultures were carried out in a fermentation vessel containing medium and sulphur as the sole energy source and maintained at 30ºC and 400 rpm. The pH was adjusted to 6.0, 7.0 or 8.0 and maintained with the automatic addition of KOH. Our results show high chromium (VI reduction values (close to 100% at the end of bacterial growth at the three pH values. The results of these experiments are very promising for development of a microbiological process to be used in the detoxification of chromium(VI-polluted effluents.

  10. Sonoassisted microbial reduction of chromium.

    Science.gov (United States)

    Kathiravan, Mathur Nadarajan; Karthick, Ramalingam; Muthu, Naggapan; Muthukumar, Karuppan; Velan, Manickam

    2010-04-01

    This study presents sonoassisted microbial reduction of hexavalent chromium (Cr(VI)) using Bacillus sp. isolated from tannery effluent contaminated site. The experiments were carried out with free cells in the presence and absence of ultrasound. The optimum pH and temperature for the reduction of Cr(VI) by Bacillus sp. were found to be 7.0 and 37 degrees C, respectively. The Cr(VI) reduction was significantly influenced by the electron donors and among the various electron donors studied, glucose offered maximum reduction. The ultrasound-irradiated reduction of Cr(VI) with Bacillus sp. showed efficient Cr(VI) reduction. The percent reduction was found to increase with an increase in biomass concentration and decrease with an increase in initial concentration. The changes in the functional groups of Bacillus sp., before and after chromium reduction were observed with FTIR spectra. Microbial growth was described with Monod and Andrews model and best fit was observed with Andrews model.

  11. Portable x-ray fluorescence for the analysis of chromium in nail and nail clippings.

    Science.gov (United States)

    Fleming, David E B; Ware, Chris S

    2017-03-01

    Assessment of chromium content in human nail or nail clippings could serve as an effective biomarker of chromium status. The feasibility of a new portable x-ray fluorescence (XRF) approach to chromium measurement was investigated through analysis of nail and nail clipping phantoms. Five measurements of 180s (real time) duration were first performed on six whole nail phantoms having chromium concentrations of 0, 2, 5, 10, 15, and 20µg/g. Using nail clippers, these phantoms were then converted to nail clippings, and assembled into different mass groups of 20, 40, 60, 80, and 100mg for additional measurements. The amplitude of the chromium Kα characteristic x-ray energy peak was examined as a function of phantom concentration for all measurement conditions to create a series of calibration lines. The minimum detection limit (MDL) for chromium was also calculated for each case. The chromium MDL determined from the whole nail intact phantoms was 0.88±0.03µg/g. For the clipping phantoms, the MDL ranged from 1.2 to 3.3µg/g, depending on the mass group analyzed. For the 40mg clipping group, the MDL was 1.2±0.1µg/g, and higher mass collections did not improve upon this result. This MDL is comparable to chromium concentration levels seen in various studies involving human nail clippings. Further improvements to the portable XRF technique would be required to detect chromium levels expected from the lower end of a typical population.

  12. Arsenic and chromium topsoil levels and cancer mortality in Spain.

    Science.gov (United States)

    Núñez, Olivier; Fernández-Navarro, Pablo; Martín-Méndez, Iván; Bel-Lan, Alejandro; Locutura, Juan F; López-Abente, Gonzalo

    2016-09-01

    Spatio-temporal cancer mortality studies in Spain have revealed patterns for some tumours which display a distribution that is similar across the sexes and persists over time. Such characteristics would be common to tumours that shared risk factors, including the chemical soil composition. The objective of the present study is to assess the association between levels of chromium and arsenic in soil and the cancer mortality. This is an ecological cancer mortality study at municipal level, covering 861,440 cancer deaths in 7917 Spanish mainland towns from 1999 to 2008. Chromium and arsenic topsoil levels (partial extraction) were determined by ICP-MS at 13,317 sampling points. To estimate the effect of these concentrations on mortality, we fitted Besag, York and Mollié models, which included, as explanatory variables, each town's chromium and arsenic soil levels, estimated by kriging. In addition, we also fitted geostatistical-spatial models including sample locations and town centroids (non-aligned data), using the integrated nested Laplace approximation (INLA) and stochastic partial differential equations (SPDE). All results were adjusted for socio-demographic variables and proximity to industrial emissions. The results showed a statistical association in men and women alike, between arsenic soil levels and mortality due to cancers of the stomach, pancreas, lung and brain and non-Hodgkin's lymphomas (NHL). Among men, an association was observed with cancers of the prostate, buccal cavity and pharynx, oesophagus, colorectal and kidney. Chromium topsoil levels were associated with mortality among women alone, in cancers of the upper gastrointestinal tract, breast and NHL. Our results suggest that chronic exposure arising from low levels of arsenic and chromium in topsoil could be a potential risk factor for developing cancer.

  13. Reduction of chromium oxides with calcium carbide during thestainless steelmaking process

    Directory of Open Access Journals (Sweden)

    B. Arh

    2015-04-01

    Full Text Available An efficient reduction of chromium from slag requires an appropriate reduction agent for the given steelmaking technology. The usual slag reduction praxis consists of carbon injections and additions of ferrosilicon and aluminum.Reduction of chromium containing slags with calcium carbide is an appealing alternative. Calcium carbide is a strong reduction agent that unlike ferrosilicon and aluminum also provides the possibility of foaming slag formation.Experimental work regarding chromium slag reduction with calcium carbide towards usual slag reduction praxis is described in this work. The results show that higher reduction rates in the stage of refining period of the melt and higher level of overall chromium reduction from slag can be reached with the blowing of CaC2.

  14. Removal of chromium from electroplating industry effluents by ion exchange resins.

    Science.gov (United States)

    Cavaco, Sofia A; Fernandes, Sandra; Quina, Margarida M; Ferreira, Licínio M

    2007-06-18

    Effluent discharged from the chromium electroplating industry contains a large number of metals, including chromium, copper, nickel, zinc, manganese and lead. The ion exchange process is an alternative technique for application in the treatment of industrial wastewater containing heavy metals and indeed it has proven to be very promising in the removal and recovery of valuable species. The main objective of the present work is to evaluate the performance of commercial ion exchange resins for removing chromium trivalent from industrial effluents, and for this purpose two resins were tested: a chelating exchange resin (Diaion CR11) and a weak cationic resin (Amberlite IRC86). In order to evaluate the sorption capacity of the resins some equilibrium experiments were carried out, being the temperature and pH the main variables considered. The chromium solutions employed in the experiments were synthetic solutions and industrial effluents. In addition, a transient test was also performed as an attempt to understand the kinetic behaviour of the process.

  15. Electrodeposition of chromium from trivalent chromium urea bath containing sulfate and chloride

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    The reduction of Cr( Ⅲ) to Cr( Ⅱ ) on copper electrode in trivalent chromium urea bath containing chromium sulfate and chromium chloride as chromium source has been investigated by potentiodynamic sweep. The transfer coefficient α for reduction of Cr( Ⅲ ) to Cr( Ⅱ ) on copper electrode was calculated as 0.46. The reduction is a quasi-reversible process. J-t responses at different potential steps showed that the generation and adsorption characteristics of carboxylate bridged oligomer are relevant to cathode potential. The interface behavior between electrode and solution for Cr( Ⅲ ) complex is a critical factor influencing sustained electrode position of chromium. The hypotheses of the electro-inducing polymerization of Cr( Ⅲ ) was proposed. The potential scope in which sustained chromium deposits can be prepared is from- 1.3 V to- 1.7 V (vs SCE) in the urea bath. Bright chromium deposits with thickness of 30 μm can be prepared in the bath.

  16. 29 CFR 1915.1026 - Chromium (VI).

    Science.gov (United States)

    2010-07-01

    ... system dysfunction; any history of asthma, dermatitis, skin ulceration, or nasal septum perforation; and... is present or is likely to be present from skin or eye contact with chromium (VI), the employer shall... cleaned in a manner that minimizes skin or eye contact with chromium (VI) and effectively prevents...

  17. 29 CFR 1926.1126 - Chromium (VI).

    Science.gov (United States)

    2010-07-01

    ... system dysfunction; any history of asthma, dermatitis, skin ulceration, or nasal septum perforation; and... is present or is likely to be present from skin or eye contact with chromium (VI), the employer shall... cleaned in a manner that minimizes skin or eye contact with chromium (VI) and effectively prevents...

  18. 29 CFR 1910.1026 - Chromium (VI).

    Science.gov (United States)

    2010-07-01

    ... activity involving chromium cannot release dusts, fumes, or mists of chromium (VI) in concentrations at or... currents that prevent the LEVs from performing efficiently. The use of fans has a similar effect. Industry... and positioning of cross drafts, fans, doors, windows, partitions and process equipment that...

  19. Immobilization in cement mortar of chromium removed from water using titania nanoparticles.

    Science.gov (United States)

    Husnain, Ahmed; Qazi, Ishtiaq Ahmed; Khaliq, Wasim; Arshad, Muhammad

    2016-05-01

    Because of the high toxicity of chromium, particularly as Cr (VI), it is removed from industrial effluents before their discharge into water bodies by a variety of techniques, including adsorption. Ultimate disposal of the sludge or the adsorbate, however, is a serious problem. While titania, in nanoparticle form, serves as a very good adsorbent for chromium, as an additive, it also helps to increase the compressive strength of mortar and concrete. Combining these two properties of the material, titania nanoparticles were used to adsorb chromium and then added to mortar up to a concentration of 20% by weight. The compressive strength of the resulting mortar specimens that replaced 15% of cement with chromium laden titania showed an improved strength than that without titania, thus confirming that this material had positive effect on the mortar strength. Leachate tests using the Toxicity Characteristics Leaching Procedure (TCLP) confirmed that the mortar sample chromium leachate was well within the permissible limits. The proposed technique thus offers a safe and viable method for the ultimate disposal of toxic metal wastes, in general, and those laden waste chromium, in particular.

  20. Black and green pigments based on chromium-cobalt spinels

    Energy Technology Data Exchange (ETDEWEB)

    Eliziario, Sayonara A., E-mail: sayonaraea@iq.unesp.br [Departamento de Fisico-Quimica, Instituto de Quimica, UNESP - Univ Estadual Paulista, Araraquara, SP (Brazil); Departamento de Quimica, CCEN, Universidade Federal da Paraiba, Campus I, Joao Pessoa, PB (Brazil); Andrade, Jeferson M. de [Departamento de Quimica, CCEN, Universidade Federal da Paraiba, Campus I, Joao Pessoa, PB (Brazil); Lima, Severino J.G. [Departamento de Engenharia Mecanica, CT, Universidade Federal da Paraiba, Campus I, Joao Pessoa, PB (Brazil); Paskocimas, Carlos A. [Universidade Federal do Rio Grande do Norte, CT, Natal, RN (Brazil); Soledade, Luiz E.B. [Departamento de Quimica, CCEN, Universidade Federal da Paraiba, Campus I, Joao Pessoa, PB (Brazil); Hammer, P.; Longo, E. [Departamento de Fisico-Quimica, Instituto de Quimica, UNESP - Univ Estadual Paulista, Araraquara, SP (Brazil); Souza, Antonio G.; Santos, Ieda M.G. [Departamento de Quimica, CCEN, Universidade Federal da Paraiba, Campus I, Joao Pessoa, PB (Brazil)

    2011-09-15

    Highlights: {yields} Co(Co{sub 2-x}Cr{sub x})O{sub 4} powders with different chromium concentrations (x = 0, 0.25 and 1) were prepared by the polymeric precursor method. {yields} Co(CoCr)O{sub 4} and Co(Co{sub 1.75}Cr{sub 0.25})O{sub 4} displayed a dark color and CoCr{sub 2}O{sub 4} was green. {yields} The colors were related to the different oxidation states of Cr and Co. {yields} Cobalt enrichment result in an increasing presence of Co(III) and a decrease amount of Cr(VI). - Abstract: Chromium and cobalt oxides are widely used in the manufacture of industrial pigments. In this work, the Co(Co{sub 2-x}Cr{sub x})O{sub 4} powders with different chromium concentrations (x = 0, 0.25 and 1) were synthesized by the polymeric precursor method, heat treatment between 600 and 1000 deg. C. These powders were characterized by X-ray diffraction, infrared spectroscopy, colorimetry, UV-vis absorption and X-ray photoelectron spectroscopies. Even with the addition of chromium, the XRD patterns revealed that all powders crystallize in a single spinel cubic structure. The spinels with higher cobalt amount, Co(CoCr)O{sub 4} and Co(Co{sub 1.75}Cr{sub 0.25})O{sub 4}, displayed a dark color, without the Co{sup 3+} reduction observed in Co{sub 3}O{sub 4} between 900 and 950 deg. C. The spinel with higher chromium amount, CoCr{sub 2}O{sub 4}, was green. The colors were directly related to the occupation of tetrahedral and octahedral sites by the chromophores, as well as to the different oxidation states of chromium and cobalt. The different optical band gap values estimated from UV-vis spectra suggested the existence of intermediary energy levels within the band gap. X-ray photoelectron spectroscopy confirmed an increasing presence of Co(III) and a decreasing amount of Cr(VI) with cobalt enrichment.

  1. Low-chromium reduced-activation chromium-tungsten steels

    Energy Technology Data Exchange (ETDEWEB)

    Klueh, R.L.; Alexander, D.J.; Maziasz, P.J. [Oak Ridge National Lab., TN (United States)

    1996-10-01

    Bainitic microstructures formed during continuous cooling can differ from classical upper and lower bainite formed during isothermal transformation. Two types of non-classical bainite were observed depending on the cooling rate: carbide-free acicular bainite at rapid cooling rates and granular bainite at slower cooling rates. The Charpy impact toughness of the acicular ferrite was found to be considerably better than for the granular bainite. It was postulated that alloying to improve the hardenability of the steel would promote the formation of acicular bainite, just as increasing the cooling rate does. To test this, chromium and tungsten were added to the 2 1/4Cr-2W and 2 1/4Cr-2WV steel compositions to increase their hardenability, and the microstructures and mechanical properties were examined.

  2. Synthesis of Chromium (Ⅲ) 5-aminosalicylate

    Institute of Scientific and Technical Information of China (English)

    LI Wei; HAO Er-jun; JIANG Yu-qin

    2004-01-01

    As we all known that diabetes is a chronic disease with major health consequences.Research has revealed that the occurrence of diabetes have great thing to do with the chromium deficient. Almost 40 years after the first report of glucose tolerance factor(GTF) [1], no conclusive evidence for an isolable ,biologically active form of chromium exited. Three materials have been proposed to be the biologically active form of chromium: "glucose tolerance factor", chromium Picolinate and low-molecular-weight chromium-binding substance (LWMCr) [2] . So there is potential for the design of new chromium drugs .5-Aminosalicylic acid (5-ASA) is identified as an active component in the therapy of inflammatory bowel disease (IBD) such as Crohn's disease and ulcerative colitis . The therapeutic action of 5-ASA is believed to be coupled to its ability to act as a free radical scavenger [3-4],acting locally on the inflamed colonic mucosa [5-7]. However, the clinical use of 5-ASA is limited, since orally administered 5-ASA is rapidly and completely absorbed from the upper gastrointestinal tract and therefore the local therapeutic effects of 5-ASA in the colon is hardly expected.In this paper, we report the synthesis of chromium(Ⅲ)5-aminosalicylate from 5-ASA and CrCl3. 6H2O.The synthesis route is as follow:The complex has been characterized by elemental analysis, IR spectra, X-ray powder diffractionand TG-DTA . They indicate that the structure is tris(5-ASA) Chromium . Experiments show that thecomplex has a good activity for supplement tiny dietary chromium, lowering blood glucose levels,lowering serum lipid levels and in creasing lean body mass .

  3. Dietary inclusion of chromium to improve growth performance and immune-competence of broilers under heat stress

    Directory of Open Access Journals (Sweden)

    Tagwa M. Norain

    2013-11-01

    Full Text Available This study was conducted to investigate the effects of dietary supplementation with chromium chloride, CrCl3.6H2O (2mg kg–1 basal diet on the performance and immune response of broiler chickens under heat stress condition (25-43°C. A total of 80 one-day-old broiler chicks (Ross-308 were assigned to two treatment groups according to a completely randomized design. Each treatment consisted of four equal replicates, each contained ten chicks. Chicks were fed on basal diets supplemented with different concentrations of chromium (0 and 2 mg kg–1 CrCl3 from 1 to 35 days of age. Chromium supplementation as feed additives resulted in a slightly lower rectal temperature, and significantly (P<0.05 lower respiration rate for the broiler chickens received diet supplemented with chromium compared to the control (0 mg kg–1 CrCl3. Dietary chromium supplementation increased final body weight (BW at the end of the production period (5 weeks. Average weight gain was significantly (P<0.05 higher in chickens fed on chromium supplemented diet. Feed intake was not influenced by dietary chromium supplementation, however, the efficiency of feed conversion was improved (P<0.05 in chromium supplemented chickens. Furthermore, dressing percentage was significantly (P<0.05 higher in Cr-treated chickens compared to control chickens. Chromium supplementation significantly (P<0.05 improved the immune response to Newcastle Disease Virus vaccine (NDV. The present results suggest that dietary chromium supplementation provides a good nutritional management approach to ameliorate heat stress induced depression in production performance and immune response of broiler chickens. 

  4. Characteristics of chromium-allergic dermatitis patients prior to regulatory intervention for chromium in leather

    DEFF Research Database (Denmark)

    Bregnbak, David; Thyssen, Jacob P; Zachariae, Claus;

    2014-01-01

    BACKGROUND: Chromium-tanned leather articles currently constitute the most important cause of contact allergy to chromium in Denmark. A regulation on the content of hexavalent chromium in leather was adopted in November 2013 by the EU member states. OBJECTIVES: To characterize patients...... with chromium allergy and their disease, to serve as a baseline for future studies on the potential effect of the new regulation on chromium in leather. METHODS: A questionnaire case-control study was performed on 155 dermatitis patients with positive patch test reactions to potassium dichromate and a matched...... control group of 621 dermatitis patients. Comparisons were made by use of a χ(2) -test and the Mann-Whitney U-test. Logistic regression analyses were used to test for associations. RESULTS: Sixty-six per cent of chromium-allergic patients had a positive history of contact dermatitis caused by leather...

  5. Chromium in leather footwear-risk assessment of chromium allergy and dermatitis

    DEFF Research Database (Denmark)

    Thyssen, Jacob P; Strandesen, Maria; Poulsen, Pia B;

    2012-01-01

    Background. Chromium-tanned leather footwear, which releases >3 ppm hexavalent Cr(VI), may pose a risk of sensitizing and eliciting allergic dermatitis. Objectives. To determine the content and potential release of chromium in leather footwear and to discuss the prevention of chromium contact...... allergy and dermatitis. Methods. Sixty pairs of leather shoes, sandals and boots (20 children's, 20 men's, and 20 women's) were purchased in Copenhagen and examined with X-ray fluorescence spectroscopy. Chromium was extracted according to the International Standard, ISO 17075. The detection level for Cr......(VI) was 3 ppm. Results. Chromium was identified in 95% of leather footwear products, the median content being 1.7% (range 0-3.3%). No association with store category or footwear category was found. A tendency for there to be a higher chromium content in footwear with high prices was shown (p(trend) = 0...

  6. Leaching of chromium from chromium contaminated soil: Speciation study and geochemical modeling

    Directory of Open Access Journals (Sweden)

    Anđelković Darko H.

    2012-01-01

    Full Text Available Distribution of chromium between soil and leachate was monitored. A natural process of percolating rainwater through the soil was simulated in the laboratory conditions and studied with column leaching extraction. Migration of chromium in the soil is conditioned by the level of chromium soil contamination, the soil organic matter content, and rainwater acidity. Chromium (III and chromium(VI were determined by spectrophotometric method with diphenilcarbazide in acidic media. Comparing the results of chromium speciation in leachate obtained by experimental model systems and geochemical modelling calculations using Visual MINTEQ model, a correlation was observed regarding the influence of the tested parameters. Leachate solutions showed that the concentration of Cr depended on the organic matter content. The influence of pH and soil organic matter content is in compliance after its definition through experimental and theoretical way. The computer model - Stockholm Humic Model used to evaluate the leaching results corresponded rather well with the measured values.

  7. Study on anaerobic treatment of wastewater containing hexavalent chromium

    Institute of Scientific and Technical Information of China (English)

    XU Yan-bin; XIAO Hua-hua; SUN Shui-yu

    2005-01-01

    A self-made anaerobic bio-filter bed which was inoculated with special sludge showed high efficiency in removing hexavalent chromium. When pump flow was 47 ml/min and CODCr ofwastewater was about 140 mg/L, it took 4 h to decrease the Cr6+ concentrations from about 60 mg/L to under 0.5 mg/L, compared with 14 h without carbon source addition. Cr6+ concentrations ranged from 64.66 mg/L to 75.53 mg/L, the system efficiency was excellent. When Cr6+ concentration reached 95.47 mg/L,the treatment time was prolonged to 7.5 h. Compared with the contrast system, the system with trace metals showed clear superiority in that the Cr6+ removal rate increased by 21.26%. Some analyses also showed that hexavalent chromium could probably be bio-reduced to trivalent chromium, and that as a result, the chrome hydroxide sediment was formed on the surface of microorganisms.

  8. Study on anaerobic treatment of wastewater containing hexavalent chromium.

    Science.gov (United States)

    Xu, Yan-bin; Xiao, Hua-hua; Sun, Shui-yu

    2005-06-01

    A self-made anaerobic bio-filter bed which was inoculated with special sludge showed high efficiency in removing hexavalent chromium. When pump flow was 47 ml/min and COD(Cr) of wastewater was about 140 mg/L, it took 4 h to decrease the Cr6+ concentrations from about 60 mg/L to under 0.5 mg/L, compared with 14 h without carbon source addition. Cr6+ concentrations ranged from 64.66 mg/L to 75.53 mg/L, the system efficiency was excellent. When Cr6+ concentration reached 95.47 mg/L, the treatment time was prolonged to 7.5 h. Compared with the contrast system, the system with trace metals showed clear superiority in that the Cr6+ removal rate increased by 21.26%. Some analyses also showed that hexavalent chromium could probably be bio-reduced to trivalent chromium, and that as a result, the chrome hydroxide sediment was formed on the surface of microorganisms.

  9. Study on anaerobic treatment of wastewater containing hexavalent chromium*

    Science.gov (United States)

    Xu, Yan-bin; Xiao, Hua-hua; Sun, Shui-yu

    2005-01-01

    A self-made anaerobic bio-filter bed which was inoculated with special sludge showed high efficiency in removing hexavalent chromium. When pump flow was 47 ml/min and CODCr of wastewater was about 140 mg/L, it took 4 h to decrease the Cr6+ concentrations from about 60 mg/L to under 0.5 mg/L, compared with 14 h without carbon source addition. Cr6+ concentrations ranged from 64.66 mg/L to 75.53 mg/L, the system efficiency was excellent. When Cr6+ concentration reached 95.47 mg/L, the treatment time was prolonged to 7.5 h. Compared with the contrast system, the system with trace metals showed clear superiority in that the Cr6+ removal rate increased by 21.26%. Some analyses also showed that hexavalent chromium could probably be bio-reduced to trivalent chromium, and that as a result, the chrome hydroxide sediment was formed on the surface of microorganisms. PMID:15909347

  10. Response of soil catalase activity to chromium contamination

    Institute of Scientific and Technical Information of China (English)

    Zofia St(e)pniewska; Agnieszka Woli(n)ska; Joanna Ziomek

    2009-01-01

    The impact of chromium (III) and (VI) forms on soil catalase activity is presented.The Orthic Podzol, Haplic Phaeozem and Mollic Gleysol from different depths were used in the experiment.The soil samples were amended with solution of Cr(III) using CrCl3, and with Cr(VI) using K2Cr2O7 in the concentration range from 0 to 20 mg/kg, whereas the samples without the addition of chromium served as control.Catalase activity was assayed by one of the commonly used spectrophotometric methods.As it is demonstrated in the experiment, both Cr(III) and Cr(VI) forms have ability to reduce soil catalase activity.A chromium dose of 20 mg/kg caused the inhibition of catalase activity and the corresponding contamination levels ranged from 75% to 92% for Cr(III) and 68% to 76% for Cr(VI), with relation to the control.Catalase activity reached maximum in the soil material from surface layers (0-25 cm), typically characterized by the highest content of organic matter creating favorable conditions for microorganisms.

  11. Achieving Zero Stress in Iridium, Chromium, and Nickle Thin Films

    Science.gov (United States)

    Broadway, David M.; Weimer, Jeffrey; Gurgew, Danielle; Lis, Tomasz; Ramsey, Brian D.; O'Dell, Stephen L.; Ames, A.; Bruni, R.

    2015-01-01

    We examine a method for achieving zero intrinsic stress in thin films of iridium, chromium, and nickel deposited by magnetron sputter deposition. The examination of the stress in these materials is motivated by efforts to advance the optical performance of light-weight x-ray space telescopes into the regime of sub-arc second resolution that rely on control of the film stress to values within 10-100 MPa. A characteristic feature of the intrinsic stress behavior in chromium and nickel is their sensitivity to the magnitude and sign of the intrinsic stress with argon gas pressure, including the existence of a critical pressure that results in zero film stress. This critical pressure scales linearly with the film's density. While the effect of stress reversal with argon pressure has been previously reported by Hoffman and others for nickel and chromium, we have discovered a similar behavior for iridium. Additionally, we have identified zero stress in iridium shortly after island coalescence. This feature of film growth is used for achieving a total internal stress of -2.89 MPa for a 15.8 nm thick iridium film. The surface roughness of this low-stress film was examined using scanning probe microscopy (SPM) and x-ray reflectivity (XRR) at CuKa and these results presented and discussed.

  12. Chromium isotope uptake in carbonates

    DEFF Research Database (Denmark)

    Rodler, Alexandra

    composition of contemporaneous seawater. Marine carbonates are ubiquitous throughout Earth’s rock record rendering them a particularly interesting archive for constraining past changes in ocean chemistry. This thesis includes an investigation of the fractionation behavior of Cr isotopesduring coprecipitation......Chromium (Cr) is a redox sensitive element potentially capable of tracing fine-scale fluctuations of the oxygenation of Earth’s early surface environments and seawater. The Cr isotope composition of carbonates could perhaps be used as paleo-redox proxy to elucidate changes in the geological past...... related to the rise of oxygen and the evolution of the biosphere. However, before the Cr isotopesystem can be applied to faithfully delineate paleo-environmental changes, careful assessment of the signal robustness and a thorough understanding of the Cr cycle in Earth system processes is necessary...

  13. Chromium (VI) adsorption on boehmite

    Energy Technology Data Exchange (ETDEWEB)

    Granados-Correa, F. [Instituto Nacional de Investigaciones Nucleares, Apartado Postal 18-1027 Col., Escandon, Delegacion Miguel Hidalgo, C.P. 11801 Mexico, D.F. (Mexico)], E-mail: fgc@nuclear.inin.mx; Jimenez-Becerril, J. [Instituto Nacional de Investigaciones Nucleares, Apartado Postal 18-1027 Col., Escandon, Delegacion Miguel Hidalgo, C.P. 11801 Mexico, D.F. (Mexico)

    2009-03-15

    Boehmite was synthesized and characterized in order to study the adsorption behavior and the removal of Cr(VI) ions from aqueous solutions as a function of contact time, initial pH solution, amount of adsorbent and initial metal ion concentration, using batch technique. Adsorption data of Cr(VI) on the boehmite were analyzed according to Freundlich, Langmuir and Dubinin-Radushkevich (D-R) adsorption models. Thermodynamic parameters for the adsorption system were determinated at 293, 303, 313 and 323 K temperatures. The kinetic values and thermodynamic parameters from the adsorption process show that the Cr(VI) ions adsorption on boehmite is an endothermic and spontaneous process. These results show that the boehmite could be considered as a potential adsorbent for chromium ions in aqueous solutions.

  14. Mechanical properties of metal-ceramic systems from nickel-chromium and cobalt-chromium alloys

    Directory of Open Access Journals (Sweden)

    Mirković Nemanja

    2007-01-01

    Full Text Available Background/Aim. Metal-ceramic bond strength and alloys' elastic modulus clearly determine the potential of alloy application, because the ceramic integrity during mastication depends on these two characteristics. The aim of this study was to evaluate metal-ceramic bond strength and elastic modulus of cobalt-chromium alloys in making porcelainfused- to-metal restorations, regarding the application of the most frequent nickel-chromium alloy. Methods. The research was performed as an experimental study. Six metalceramic samples were made from nickel-chromium alloy (Wiron 99 and cobalt-chromium alloy (Wirobond C, according to the manufactures manuals and instructions from ISO 9693: 1996. Three-point bending test was performed up to the ceramic fracture. The fracture load was measured on an universal testing machine (Zwick, type 1464, with cross-head speed of 0,05mm/min. Results. The results of this study confirmed the significant differences between the metal-ceramic bond strength (p < 0.01 and elastic modulus (p < 0.001 of nickel-chromium and cobalt-chromium alloys, where cobalt-chromium alloys showed higher values for both tested parameters. Conclusion. Cobalt-chromium metal-ceramic alloys can successfully replace nickel-chromium alloys, especially for fabrication of long-span metal-ceramic bridges due to the great flexural strength.

  15. Recovery of Chromium from Waste Taning Liquors by Magnesium Oxide

    Directory of Open Access Journals (Sweden)

    Mahmood M. Barbooti

    2010-10-01

    Full Text Available This is a case study of AL-Za’afaraniya tanning factory, 15 km to the south of Baghdad, to spot light on simple chemical treatment of the discharged water to solve the environmental problems associated with its chromium content management. The treatment was extended to the recovery and reuse of chromium. Chromium was precipitated by the addition of magnesium oxide which also aid as a neutralizer for the acidic effluent. The laboratory treatment was carried out to find the optimum conditions. The wastewater samples were taken from the outline area of the tannery. Box-Wilson method was adopted to find useful relationships between the operating variables (temperature, mixing period and magnesium oxide dose and the pH and chromium content of effluent. The experimental data were successfully fitted to second order polynomial mathematical models for the treatment. The most favorable operating conditions for the treatment were: temperature, 30 ºC; mixing period, 50 min and magnesium oxide concentration, 3000 mg/L. On using the optimum conditions a mathematical model simulating the operation for the treatment was obtained as follows:Cr = 6.0848 – 0.001839 X11 – 0.105334 X12 – 0.041038 X13pH = 10.29086 – 0.001223 X11 – 0.140043 X12 – 0.00953 X13Experimentally Cr concentration was decreased to about (0.5 mg/L in wastewater after raising the pH value to (7.35 by adding magnesium oxide.

  16. AEROSOL BEHAVIOR IN CHROMIUM WASTE INCINERATION

    Institute of Scientific and Technical Information of China (English)

    Suyuan Yu

    2003-01-01

    Cr2O3 is considered as the dominant incineration product during the combustion disposal of chromium waste. A hydrogen/air diffusion flame was employed to simulate the industrial process of incineration. Cr2O3 aerosols were generated inside the flame by the gas phase reaction of chromium and oxygen. Chromium came from the rapid decomposition of chromium hexacarbonyl (Cr(CO)6) at room temperature and was carried into the combustion chamber by hydrogen. Aerosol and clusters can then be easily formed in the flame by nucleation and coagulation. A two dimensional Discrete-Sectional Model (DSM) was adopted to calculate the Cr2O3 aerosol behavior. The experimental measurement method was Dynamic Light Scattering. The numerically predicted results agreed well with those of the experimental measurement. Both results show that the Cr2O3 aerosol size reached about 70 nanometers at the flame top.

  17. Localized Corrosion of Chromium Coated Steel

    NARCIS (Netherlands)

    Zhang, X.; Beentjes, P.; Mol, A.; Terryn, H.

    2006-01-01

    In this paper, we report on the studies of the local corrosion behaviour of chromium-coated ultra low carbon steel in NaCl solution using polarization, electrochemical impedance spectroscopy (EIS) and SVET.

  18. CHROMIUM CONCENTRATION IN TEHRAN ELECTROPLATING PLANTS

    Directory of Open Access Journals (Sweden)

    M. Ghiasseddin

    1988-12-01

    Full Text Available Hazards of soluable hexa and trivalent chromium have been documented by many investigators. But there was no information regarding safety of about 5000 workers at exposure risk to chromium in 600 primitive electroplating work shops of Tehran. During this study more than 70% of work shops were inactive due to some of their own problems. Out of active plants those that were relatively more cooperative 43 manual and 3 semi automatic were investigated for chromium concentration both by personal and environmental Sampling. The Samples were analyzed by AAS and cholormetry. In 30% of personal and 40% of environmental samples both total and Cr+6 were higher than ACGIH’S TLV. In one of semiautomatic plant Cr=6 was as high as 0.71 mg/m.3.Regarding injuries, following observations were made: Nasal wound 85%, skin irritation 73% , Dermatitis 35% and some other chromium related injuries including 2 cases of Septum perforations.

  19. Potentiometry: A Chromium (III) -- EDTA Complex

    Science.gov (United States)

    Hoppe, J. I.; Howell, P. J.

    1975-01-01

    Describes an experiment that involves the preparation of a chromium (III)-EDTA compound, a study of its infrared spectrum, and the potentiometric determination of two successive acid dissociation constants. (Author/GS)

  20. Toxicodynamic and toxicokinetic descriptors of combined chromium (VI) and nickel toxicity.

    Science.gov (United States)

    Minigaliyeva, Ilzira A; Katsnelson, Boris A; Privalova, Larisa I; Gurvich, Vladimir B; Panov, Vladimir G; Varaksin, Anatoly N; Makeyev, Oleg H; Sutunkova, Marina P; Loginova, Nadezhda V; Kireyeva, Ekaterina P; Grigoryeva, Ekaterina V; Slyshkina, Tatyana V; Ganebnykh, Eugenia V; Grebenkina, Svetlana V

    2014-01-01

    After repeated intraperitoneal injections of nickel and chromium (VI) salts to rats, we found, and confirmed by mathematical modeling, that their combined subchronic toxicity can either be of additive type or depart from it (predominantly toward subadditivity) depending on the effect assessed. Against the background of moderate systemic toxicity, the combination under study proved to possess a marked additive genotoxicity assessed by means of the random amplification of polymorphic DNA test. We also demonstrated that chromium and nickel reciprocally influenced the retention of these metals in some organs (especially in the spleen) but not their urinary excretion in this study.

  1. Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, Low-Carbon Nickel-Chromium-Molybdenum-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Tungsten, and Low-Carbon Nickel-Molybdenum-Chromium Alloy Plate, Sheet, and Strip

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2015-01-01

    Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, Low-Carbon Nickel-Chromium-Molybdenum-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Tungsten, and Low-Carbon Nickel-Molybdenum-Chromium Alloy Plate, Sheet, and Strip

  2. Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2015-01-01

    Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod

  3. Permeation of chromium salts through human skin in vitro

    DEFF Research Database (Denmark)

    Gammelgaard, Bente; Fullerton, A; Avnstorp, C

    1992-01-01

    Chromium permeation studies were performed on full thickness human skin in diffusion cells. All samples were analysed for the total chromium content by graphite furnace Zeeman-corrected atomic absorption spectrometry. Some samples were analysed by an ion chromatographic method permitting...... the simultaneous determination of Cr(VI) and Cr(III) as well. The amounts of chromium found in all skin layers were significantly higher when potassium dichromate was applied to the skin compared with chromium chloride or chromium nitrate. Chromium could only be detected in the recipient phase after application...... of the dichromate solution. Chromium skin levels increased with increasing concentrations of applied chromium salts up to 0.034 M Cr. The amount of chromium in recipient phase and skin layers increased with increasing pH when the applied solution contained potassium dichromate. This was ascribed to a decreased skin...

  4. Direct access to macroporous chromium nitride and chromium titanium nitride with inverse opal structure.

    Science.gov (United States)

    Zhao, Weitian; DiSalvo, Francis J

    2015-03-21

    We report a facile synthesis of single-phase, nanocrystalline macroporous chromium nitride and chromium titanium nitride with an inverse opal morphology. The material is characterized using XRD, SEM, HR-TEM/STEM, TGA and XPS. Interconversion of macroporous CrN to Cr2O3 and back to CrN while retaining the inverse opal morphology is also demonstrated.

  5. The Key Technique of Manufacture of Dense Chromium Sesquioxide Refractories

    Institute of Scientific and Technical Information of China (English)

    LIMaoqiang; ZHANGShuying; 等

    1998-01-01

    Dense chromium sesquioxide refractories have widely been used in the kilns for making alkai-free and anti-alkali glass fibers due to their excellent re-sistance to molten glasses.Densifications of chromium sesquioxide during sintering can be blocked by evaporation of chromium trioxide derived from oxidation at high temperature,In this paper the mech-anism of sintering chromium oxide and the process-ing technique for making dense chromium sesquiox-ide refractories are discussed .A process in laboratory scale for making dense chromium sesquioxide bricks is demonstrated.

  6. Study on anaerobic treatment of wastewater containing hexavalent chromium*

    OpenAIRE

    Xu, Yan-Bin; Xiao, Hua-hua; Sun, Shui-yu

    2005-01-01

    A self-made anaerobic bio-filter bed which was inoculated with special sludge showed high efficiency in removing hexavalent chromium. When pump flow was 47 ml/min and CODCr of wastewater was about 140 mg/L, it took 4 h to decrease the Cr6+ concentrations from about 60 mg/L to under 0.5 mg/L, compared with 14 h without carbon source addition. Cr6+ concentrations ranged from 64.66 mg/L to 75.53 mg/L, the system efficiency was excellent. When Cr6+ concentration reached 95.47 mg/L, the treatment ...

  7. Isocyanide and Phosphine Oxide Coordination in Binuclear Chromium Pacman Complexes.

    Science.gov (United States)

    Stevens, Charlotte J; Nichol, Gary S; Arnold, Polly L; Love, Jason B

    2013-12-01

    The new binuclear chromium Pacman complex [Cr2(L)] of the Schiff base pyrrole macrocycle H4L has been synthesized and structurally characterized. Addition of isocyanide, C≡NR (R = xylyl, (t)Bu), or triphenylphosphine oxide donors to [Cr2(L)] gives contrasting chemistry with the formation of the new coordination compounds [Cr2(μ-CNR)(L)], in which the isocyanides bridge the two Cr(II) centers, and [Cr2(OPPh3)2(L)], a Cr(II) phosphine oxide adduct with the ligands exogenous to the cleft.

  8. Synthesis of a new complex Chromium (Ⅲ) 2-mercaptonicotinate

    Institute of Scientific and Technical Information of China (English)

    LI Wei; HAO Er-jun; JIANG Yu-qin

    2004-01-01

    Chromium is an essential trace element for mammals[1-3].Diabetes is a chronic disease with major health consequence. Studies show that the occurrence of diabetes have great thing to do with the chromium deficient. Almost 40 years after the first report of glucose tolerance factor(GTF)[4]no conclusive evidence for an isolable ,biologically active form of chromium exited. Three materials have been proposed to be the biologically active form of chromium: "glucose tolerance factor", chromium Picolinate and low-molecular-weight chromium-binding substance (LWMCr)[5]So there is potential for the design of new chromium drugs[6].Chromium compounds have been used in medicine for centuries and there is potential for the design of new chromium drugs.2-Mercaptonicotinic acid(MN) displays the interesting biological activity. Chromium( Ⅲ )2-mercaptonicotinate is a common and effective biologically active form of Chromium. The test of biological activity indicated that may be useful in treating of diabetes. In this paper, we reported the The synthesis route is as follow:The structure of the complex has been characterized by IR, elemental analysis, MS,atomic absorption spectroscopy, X-ray powder diffraction and TG-DTA analysis.They indicate that the structure of Chromium 2-mercaptonicotinate.HPLC is used for determination of the purity. Studies show that the complex has a good biological activity for supplement tiny dietary chromium,lowering blood glucose levels, lowering serum lipid levels and increasing lean body mass.

  9. Alternatives for hard chromium plating: Nanostructured coatings for severe-service valves

    Energy Technology Data Exchange (ETDEWEB)

    Vernhes, L. [Department of Engineering Physics, Ecole Polytechnique, C.P. 6079, Succ. Centre Ville, Montreal, Quebec, Canada H3C 3A7 (Canada); Velan Inc., 7007 Côte de Liesse, Montreal, Quebec, Canada H4T 1X8 (Canada); Azzi, M. [Department of Mechanical Engineering, Notre Dame University-Louize (Lebanon); Klemberg-Sapieha, J.E., E-mail: jsapieha@polymtl.ca [Department of Engineering Physics, Ecole Polytechnique, C.P. 6079, Succ. Centre Ville, Montreal, Quebec, Canada H3C 3A7 (Canada)

    2013-07-15

    In this paper, a variety of chromium-free protective coatings were evaluated as alternatives for hard chromium (HC) electroplating for valve applications, such as nanostructured cobalt-phosphor (NCP) deposited by electroplating and tungsten/tungsten carbide (W/WC) prepared by chemical vapor deposition. A series of laboratory tests including hardness, micro scratch, pin-on-disk and electrochemical polarization measurements were performed in order to compare the performance of the different coatings. In addition, mechanical resistance and fatigue resistance were evaluated using prototype valves with coated ball under severe tribo-corrosion conditions. It was shown that W/WC coating exhibits superior resistance to wear and corrosion due to high hardness and high resistance to pitting, respectively while NCP exhibits better wear resistance than HC with alumina ball and low corrosion potential which allow to use it as protective (sacrificial) coating. Both nanostructured coatings exhibited attractive tribo-mechanical and functional characteristics compared to hard chromium. - Highlights: • Tungsten/tungsten carbide (W/WC) and cobalt-phosphor (NCP) coatings are compared with hard chromium (HC). • NCP and W/WC offer better tribological properties (wear rate and friction coefficient) than HC. • W/WC has demonstrated a robust corrosion behavior with a breakdown potential greater than 1 V. • NCP and W/WC are potential candidates to replace hard chromium as protective coating.

  10. High temperature oxidation of iron-chromium alloys

    Energy Technology Data Exchange (ETDEWEB)

    Mikkelsen, Lars

    2003-06-15

    The high temperature oxidation of the ferritic alloy Fe78Cr22 has been investigated in the present work. The effect of small alloying additions of cerium and/or silicon was also investigated. The alloys were oxidized at 973, 1173 and 1373 K in either air or a hydrogen/argon mixture. The various reaction atmospheres contained between 0.02 and 50% water vapour. The oxide scales formed on the various alloys at 973 K consisted of thin chromia layers. The oxide scales grown on the alloys at 1173 K also consisted of a chromia layer. The microstructure of the chromia scales was found to depend on the reaction atmosphere. The chromia scales grown in hydrogen/argon atmospheres formed oxide whiskers and oxide ridges at the surface of the scales, while the chromia scales grown in air formed larger oxide grains near the surface. This difference in oxide microstructure was due to the vaporization of chromium species from the chromia scales grown in air. Two different growth mechanisms are proposed for the growth of oxide whiskers. The growth rate of the chromia scales was independent of the oxygen activity. This is explained by a growth mechanism of the chromia scales, where the growth is governed by the diffusion of interstitial chromium. The addition of silicon to the iron-chromium alloy resulted in the formation of silica particles beneath the chromia scale. The presence of silicon in the alloy was found to decrease the growth rate of the chromia scale. This is explained by a blocking mechanism, where the silica particles beneath the chromia scale partly block the outwards diffusion of chromium from the alloy to the chromia scale. The addition of cerium to the iron-chromium alloy improved the adhesion of the chromia scale to the alloy and decreased the growth rate of chromia. It was observed that the minimum concentration of cerium in the alloy should be 0.3 at.% in order to observe an effect of the cerium addition. The effect of cerium is explained by the &apos

  11. Influence of tungsten and titanium on the structure of chromium cast iron

    Directory of Open Access Journals (Sweden)

    D. Kopyciński

    2012-01-01

    Full Text Available The paper analyses the as-cast state structure of chromium cast iron designed for operation under harsh impact-abrasive conditions. In the process of chromium iron castings manufacture, very strong influence on the structure of this material have the parameters of the technological process. Among others, adding to the Fe-Cr-C alloy the alloying elements like tungsten and titanium leads to the formation of additional carbides in the structure of this cast iron, which may favourably affect the casting properties, including the resistance to abrasive wear.

  12. Effect of boron carbide on primary crystallization of chromium cast iron

    Directory of Open Access Journals (Sweden)

    A. Studnicki

    2008-04-01

    Full Text Available In the paper results of the influence of boron carbide (B4C as inoculant of abrasion-resisting chromium cast iron (about 2,8% carbon and 18% chromium on primary crystallization researches are presented. Boron carbide dispersion was introduced at the bottom of pouring ladle before tap of liquid cast iron. In this investigations were used three different quantities of inoculant in amounts 0,1%; 0,2% and 0,3% with relation to bath weight. It has been demonstrated that such small additions of boron carbide change primary crystallization parameters, particularly temperature characteristic of process, their time and kinetics.

  13. MICROBIAL LEACHING OF CHROMIUM FROM SOLIDIFIED WASTE FORMS – A KINETIC STUDY

    OpenAIRE

    Carmalin Sophia Ayyappan

    2015-01-01

    In this study, Thiobacillus thiooxidans (T. thiooxidans) was used to study the microbial stability / degradation of cement-based waste forms. The waste forms contained a chromium salt (CrCl3·6H2O), cement and other additives viz., lime and gypsum in two different proportions. The experimental samples of all the simulated waste forms showed evidence of microbial growth as indicated by substantial increase in sulfate. Chromium leached from the waste forms was found to be lowest in cement – lime...

  14. Serum chromium levels in gestational diabetes mellitus

    Directory of Open Access Journals (Sweden)

    P G Sundararaman

    2012-01-01

    Full Text Available Objective: To measure serum chromium level in women with gestational diabetes mellitus (GDM from Chennai, South India. Materials and Methods: Thirty women with gestational diabetes, 60 age matched controls. Inclusion criteria: Gestational age 22-28 weeks, age group 20-35 years. Exclusion Criteria: Gestational age beyond 28 weeks, malnutrition or presence of infection. Serum chromium was measured using inductive couple plasma emission spectrometer. Results: Serum chromium levels of women with GDM, 1.59+/-0.02 ng/ml (range: 0.16-4.0 ng/ml were lower than in controls (4.58+/-0.62 ng/ml; range 0.82-5.33 ng/ml (P < 0.001. However, there were no significant differences among cases and controls when subdivided by parity. Conclusions: Women with GDM from a South Indian city had lower levels of serum chromium compared to pregnant women without GDM. Studies may be done whether chromium supplementation is useful in this group of women.

  15. Surface Chemistry and Spectroscopy of Chromium in Inorganic Oxides

    NARCIS (Netherlands)

    Weckhuysen, B.M.; Wachs, I.E.; Schoonheydt, R.A.

    1996-01-01

    Focuses on the surface chemistry and spectroscopy of chromium in inorganic oxides. Characterization of the molecular structures of chromium; Mechanics of hydrogenation-dehydrogenation reactions; Mobility and reactivity on oxidic surfaces.

  16. Thermodynamic studies of chromium adsorption on iron species generated by electrocoagulation

    Energy Technology Data Exchange (ETDEWEB)

    Parga, J.R.; Vazquez, V.; Gonzalez, G.; Cisneros, M.M. [Metallurgy and Materials Science Department, Institute Technology of Saltillo (Mexico)

    2010-10-15

    The protection of the global environment and in particular, the provision of a sustainable source of clean water is a necessity for human survival. Specifically, large quantities of chromium containing compounds are being discharged into the environment. This study has been carried out to determine the feasibility of chromium adsorption on iron species by an Electrocoagulation (EC) process using the Langmuir Isotherm. The full potential of EC with air injection as an alternative wastewater treatment technique to remove chromium from well water shows more than 99 % removal without the addition of any chemical reagents. In this study, X-Ray Diffraction, Scanning Electron Microscopy, Moessbauer Spectroscopy and Fourier Transform Infrared Spectroscopy are used to characterize the solid products that reveal the expected crystalline iron oxides, i.e., lepidocrocite, magnetite, gohetite, and iron oxide. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

  17. Serum chromium levels sampled with steel needle versus plastic IV cannula. Does method matter?

    DEFF Research Database (Denmark)

    Penny, Jeannette Ø; Overgaard, Søren

    2010-01-01

    PURPOSE: Modern metal-on-metal (MoM) joint articulations releases metal ions to the body. Research tries to establish how much this elevates metal ion levels and whether it causes adverse effects. The steel needle that samples the blood may introduce additional chromium to the sample thereby...... causing bias. This study aimed to test that theory. METHODS: We compared serum chromium values for two sampling methods, steel needle and IV plastic cannula, as well as sampling sequence in 16 healthy volunteers. RESULTS: We found statistically significant chromium contamination from the steel needle...... with mean differences between the two methods of 0.073 ng/mL, for the first sample, and 0.033 ng/mL for the second. No difference was found between the first and second plastic sample. The first steel needle sample contained an average of 0.047 ng/mL more than the second. This difference was only borderline...

  18. Analysis of the structure of castings made from chromium white cast iron resistant to abrasive wear

    Directory of Open Access Journals (Sweden)

    D. Kopyciński

    2009-10-01

    Full Text Available It has been proved that an addition of boron carbide and disintegrated steel scrap introduced as an inoculant to the chromium white cast iron changes the structure of castings. The said operation increases the number of crystallization nuclei for dendrites of the primary austenite. In this case, the iron particles act as substrates for the nucleation of primary austenite due to a similar crystallographic lattice. The more numerous are the dendrites of primary austenite and the structure more refined and the mechanical properties higher. Castings after B4C inoculation revealed a different structure of fine grained fracture. Primary precipitates of chromium carbide also appeared, reducing the mechanical properties of as-cast parts. Properly established heat treatment regime makes chromium iron castings regain their, originally high, mechanical properties.

  19. Residual Chromium in Leather by Instrumental Neutron Activation Analysis

    OpenAIRE

    S. Okoh; I. O. Okunade; D. J. Adeyemo; Ahmed, Y A; A. A. Audu; E. Amali

    2012-01-01

    Problem statement: Most tanning processes employ the use of chromium sulphate. For chromium tanned leather, finished products may contain high amount of residual chromium. This may pose some health hazards, since chromium is known to be toxic at elevated concentration. This justifies the need for the study. Approach: Various samples of leather were collected from a tannery, a leather crafts market, a leather dump site and from local tanners all in Kano, Nigeria in 2009. The samples were irrad...

  20. Hexavalent and trivalent chromium in leather: What should be done?

    Science.gov (United States)

    Moretto, Angelo

    2015-11-01

    Trivalent chromium compounds are used for leather tanning, and chromium may be released during use of leather goods. In certain instances, small amounts of hexavalent chromium can be formed and released. Both trivalent and hexavalent chromium can elicit allergic skin reaction in chromium sensitised subjects, the latter being significantly more potent. Induction of sensitisation only occurs after exposure to hexavalent chromium. A minority of subjects are sensitised to chromium, and in a fraction of these subjects allergic skin reaction have been described after wearing leather shoes or, less frequently, other leather goods. The evidence that in all these cases the reaction is related to hexavalent chromium is not always strong. The content of hexavalent chromium in leather is regulated in European Union, but rate of release rather than content is relevant for allergic skin reaction. The role of trivalent chromium appear much less relevant if at all. Modern tanning procedure do not pose significant risk due to either hexavalent or trivalent chromium. Dismissing bad quality and worn-off leather goods is relevant in reducing or eliminating the skin reaction. It should also be pointed out that shoe components or substances other than chromium in leather may cause allergic/irritative skin reactions.

  1. Standard Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625), Nickel-Chromium-Molybdenum-Silicon Alloy (UNS N06219), and Nickel-Chromium-Molybdenum-Tungsten Alloy (UNS N06650) Rod and Bar

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2014-01-01

    Standard Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625), Nickel-Chromium-Molybdenum-Silicon Alloy (UNS N06219), and Nickel-Chromium-Molybdenum-Tungsten Alloy (UNS N06650) Rod and Bar

  2. Studying chromium biosorption using arabica coffee leaves

    Directory of Open Access Journals (Sweden)

    Luis Carlos Florez García

    2010-05-01

    Full Text Available This work was aimed at providing an alternative for removing heavy metals such as chromium from waste water (effluent from the leather industry and galvanoplasty (coating with a thin layer of metal by electrochemical means, using coffee leaves as bio- mass. Using arabica coffee (Castle variety leaves led to 82% chromium removal efficiency for 1,000 mg/L synthetic dissolutions in 4 pH dissolution operating conditions, 0 rpm agitation, 0.149 mm diameter biomass particle size and 0.85 g/ml biomass / dissolution volume ratio.

  3. New mixed aluminium–chromium diarsenate

    Directory of Open Access Journals (Sweden)

    Mohamad Alem Bouhassine

    2017-03-01

    Full Text Available Potassium chromium aluminium diarsenate, KCr1/4Al3/4As2O7, was prepared by solid-state reaction. The structure consists of (Cr1/4/Al3/4O6 octahedra and As2O7 diarsenate groups sharing corners to build up a three-dimensional anionic framework. The potassium cations are located in wide channels running along the c-axis direction. The crystal structure is isostructural with the triclinic AIMIIIX2O7 (AI = alkali metal; MIII = Al, Cr, Fe; X = As, P compounds. However, the MIII octahedrally coordinated site is 25% partially occupied by chromium and 75% by aluminium.

  4. Strategies for chromium bioremediation of tannery effluent.

    Science.gov (United States)

    Garg, Satyendra Kumar; Tripathi, Manikant; Srinath, Thiruneelakantan

    2012-01-01

    Bioremediation offers the possibility of using living organisms (bacteria, fungi, algae,or plants), but primarily microorganisms, to degrade or remove environmental contaminants, and transform them into nontoxic or less-toxic forms. The major advantages of bioremediation over conventional physicochemical and biological treatment methods include low cost, good efficiency, minimization of chemicals, reduced quantity of secondary sludge, regeneration of cell biomass, and the possibility of recover-ing pollutant metals. Leather industries, which extensively employ chromium compounds in the tanning process, discharge spent-chromium-laden effluent into nearby water bodies. Worldwide, chromium is known to be one of the most common inorganic contaminants of groundwater at pollutant hazardous sites. Hexavalent chromium poses a health risk to all forms of life. Bioremediation of chromium extant in tannery waste involves different strategies that include biosorption, bioaccumulation,bioreduction, and immobilization of biomaterial(s). Biosorption is a nondirected physiochemical interaction that occurs between metal species and the cellular components of biological species. It is metabolism-dependent when living biomass is employed, and metabolism-independent in dead cell biomass. Dead cell biomass is much more effective than living cell biomass at biosorping heavy metals, including chromium. Bioaccumulation is a metabolically active process in living organisms that works through adsorption, intracellular accumulation, and bioprecipitation mechanisms. In bioreduction processes, microorganisms alter the oxidation/reduction state of toxic metals through direct or indirect biological and chemical process(es).Bioreduction of Cr6+ to Cr3+ not only decreases the chromium toxicity to living organisms, but also helps precipitate chromium at a neutral pH for further physical removal,thus offering promise as a bioremediation strategy. However, biosorption, bioaccumulation, and

  5. Chromium allergy and dermatitis: prevalence and main findings

    DEFF Research Database (Denmark)

    Bregnbak, David; Johansen, Jeanne D.; Jellesen, Morten Stendahl;

    2015-01-01

    The history of chromium as an allergen goes back more than a century, and includesan interventional success with national legislation that led to significant changes inthe epidemiology of chromium allergy in construction workers. The 2015 EU Leather Regulation once again put a focus on chromium...... allergy, emphasizing that the investigation of chromium allergy is still far from complete. Our review article on chromium focuses on the allergen’s chemical properties, its potential exposure sources, and the allergen’s interaction with the skin, and also provides an overview of the regulations...

  6. Pharmacokinetic Modeling of Trivalent and Hexavalent Chromium Based on Ingestion and Inhalation of Soluble Chromium Compounds.

    Science.gov (United States)

    1991-12-01

    be largely Cr(III) although some Cr(VI) exposure probably also occurs. Stainless-steel welders are exposed to nickel as well as to chromium compounds...welders are equivocal with respect to involvement of chromium, particularly since nickel in some chemical forms is an established lung carcinogen (Stern...microglobulin (Lindberg and Vesterberg, 1983), retinol-binding protein (Franchini and Mutti , 1988), B-glucuronidase ( Mutti et al., 1979), and kidney brush border

  7. Biological groundwater treatment for chromium removal at low hexavalent chromium concentrations.

    Science.gov (United States)

    Mamais, Daniel; Noutsopoulos, Constantinos; Kavallari, Ioanna; Nyktari, Eleni; Kaldis, Apostolos; Panousi, Eleni; Nikitopoulos, George; Antoniou, Kornilia; Nasioka, Maria

    2016-06-01

    The objective of this work is to develop and evaluate biological groundwater treatment systems that will achieve hexavalent chromium reduction and total chromium removal from groundwater at hexavalent chromium (Cr(VI)) groundwater concentrations in the 0-200 μg/L range. Three lab-scale units operated, as sequencing batch reactors (SBR) under aerobic, anaerobic and anaerobic-aerobic conditions. All systems received groundwater with a Cr(VI) content of 200 μg/L. In order to support biological growth, groundwater was supplemented with milk, liquid cheese whey or a mixture of sugar and milk to achieve a COD concentration of 200 mg/L. The results demonstrate that a fully anaerobic system or an anaerobic-aerobic system dosed with simple or complex external organic carbon sources can lead to practically complete Cr(VI) reduction to Cr(III). The temperature dependency of maximum Cr(VI) removal rates can be described by the Arrhenius relationship. Total chromium removal in the biological treatment systems was not complete because a significant portion of Cr(III) remained in solution. An integrated system comprising of an anaerobic SBR followed by a sand filter achieved more than 95% total chromium removal thus resulting in average effluent total and dissolved chromium concentrations of 7 μg/L and 3 μg/L, respectively.

  8. The electronic structure of antiferromagnetic chromium

    DEFF Research Database (Denmark)

    Skriver, Hans Lomholt

    1981-01-01

    The author has used the local spin density formalism to perform self-consistent calculations of the electronic structure of chromium in the non-magnetic and commensurate antiferromagnetic phases, as a function of the lattice parameter. A change of a few per cent in the atomic radius brings...

  9. A Kinetic Model of Chromium in a Flame

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Chromium has been identified as a carcinogenic metal.Incineration is the useful method for disposal of toxic chromium hazard waste and a chromium kinetic model in a flame is very important to study chromium oxidation.Chromium chemical kinetics over a range of temperatures of a hydrogen/air flame is proposed.Nine chromium compounds and fifty-eight reversible chemical reactions were considered The forward reaction rates are calculated based on the molecular collision approach for unknown ones and Arrhenius's Law for known ones.The backward reaction rates were calculated according to forward reaction rates, the equilibrium constants and chemical thermodynamics.It is verified by several equilibrium cases and is tested by a hydrogen/air diffusion flame.The results show that the kinetic model could be used in cases in which the chromium kinetics play an important role in a flame

  10. Chromium, chromium isotopes and selected trace elements, western Mojave Desert, USA

    Energy Technology Data Exchange (ETDEWEB)

    Izbicki, John A. [U.S. Geological Survey, 4165 Spruance Road, Suite O, San Diego, CA 92123 (United States)], E-mail: jaizbick@usgs.gov; Ball, James W. [U.S. Geological Survey, 3215 Marine Street, Boulder, Colorado, CO 80303 (United States); Bullen, Thomas D. [U.S. Geological Survey, 345 Middlefield Road, Building 15, McKelvey Building, MS-420, Menlo Park, CA 94025 (United States); Sutley, Stephen J. [Denver Federal Center, P.O. Box 25046, MS-964, Denver, CO 80225-0046 (United States)

    2008-05-15

    Chromium(VI) concentrations in excess of the California Maximum Contaminant Level (MCL) of 50 {mu}g/L occur naturally in alkaline, oxic ground-water in alluvial aquifers in the western Mojave Desert, southern California. The highest concentrations were measured in aquifers eroded from mafic rock, but Cr(VI) as high as 27 {mu}g/L was measured in aquifers eroded from granitic rock. Chromium(VI) concentrations did not exceed 5 {mu}g/L at pH < 7.5 regardless of geology. {delta}{sup 53}Cr values in native ground-water ranged from 0.7 to 5.1 per mille and values were fractionated relative to the average {delta}{sup 53}Cr composition of 0 per mille in the earth's crust. Positive {delta}{sup 53}Cr values of 1.2 and 2.3 per mille were measured in ground-water recharge areas having low Cr concentrations, consistent with the addition of Cr(VI) that was fractionated on mineral surfaces prior to entering solution. {delta}{sup 53}Cr values, although variable, did not consistently increase or decrease with increasing Cr concentrations as ground-water flowed down gradient through more oxic portions of the aquifer. However, increasing {delta}{sup 53}Cr values were observed as dissolved O{sub 2} concentrations decreased, and Cr(VI) was reduced to Cr(III), and subsequently removed from solution. As a result, the highest {delta}{sup 53}Cr values were measured in water from deep wells, and wells in discharge areas near dry lakes at the downgradient end of long flow paths through alluvial aquifers. {delta}{sup 53}Cr values at an industrial site overlying mafic alluvium having high natural background Cr(VI) concentrations ranged from -0.1 to 3.2 per mille . Near zero {delta}{sup 53}Cr values at the site were the result of anthropogenic Cr. However, mixing with native ground-water and fractionation of Cr within the plume increased {delta}{sup 53}Cr values at the site. Although {delta}{sup 53}Cr was not necessarily diagnostic of anthropogenic Cr, it was possible to identify the extent

  11. Effect of recasting on the elastic modulus of metal-ceramic systems from nickel-chromium and cobalt-chromium alloys

    Directory of Open Access Journals (Sweden)

    Mirković Nemanja

    2007-01-01

    Full Text Available Background/Aim. Elastic modulus of metal-ceramic systems determines their flexural strength and prevents damages on ceramics during mastication. Recycling of basic alloys is often a clinical practice, despite the possible effects on the quality of the future metal-ceramic dentures. This research was done to establish recasting effects of nickel-chromium and cobalt-chromium alloys on the elastic modulus of metalceramic systems in making fixed partial dentures. Methods. The research was performed as an experimental study. Six metal-ceramic samples of nickel-chromium alloy (Wiron 99 and cobalt-chromium alloy (Wirobond C were made. Alloy residues were recycled through twelve casting generations with the addition of 50% of new alloy on the occasion of every recasting. Three- point bending test was used to determine elastic modulus, recommended by the standard ISO 9693:1999. Fracture load for damaging ceramic layer was recorded on the universal testing machine (Zwick, type 1464, with the speed of 0,05 mm/min. Results. The results of this research revealed significant differences between elasticity modules of metal-ceramic samples in every examined recycle generation. Recasting had negative effect on the elastic modulus of the examined alloys. This research showed the slight linear reduction of elastic modulus up to the 6th generation of recycling. After the 6th recycling there was a sudden fall of elastic modulus. Conclusion. Recasting of nickelchromium and cobalt-chromium alloys is not recommended because of the reduced elastic modulus of these alloys. Instead of reusing previously recasted alloys, the alloy residues should be returned to the manufacturer. .

  12. Electroanalytical sensing of chromium(III) and (VI) utilising gold screen printed macro electrodes.

    Science.gov (United States)

    Metters, Jonathan P; Kadara, Rashid O; Banks, Craig E

    2012-02-21

    We report the fabrication of gold screen printed macro electrodes which are electrochemically characterised and contrasted to polycrystalline gold macroelectrodes with their potential analytical application towards the sensing of chromium(III) and (VI) critically explored. It is found that while these gold screen printed macro electrodes have electrode kinetics typically one order of magnitude lower than polycrystalline gold macroelectrodes as is measured via a standard redox probe, in terms of analytical sensing, these gold screen printed macro electrodes mimic polycrystalline gold in terms of their analytical performance towards the sensing of chromium(III) and (VI), whilst boasting additional advantages over the macro electrode due to their disposable one-shot nature and the ease of mass production. An additional advantage of these gold screen printed macro electrodes compared to polycrystalline gold is the alleviation of the requirement to potential cycle the latter to form the required gold oxide which aids in the simplification of the analytical protocol. We demonstrate that gold screen printed macro electrodes allow the low micro-molar sensing of chromium(VI) in aqueous solutions over the range 10 to 1600 μM with a limit of detection (3σ) of 4.4 μM. The feasibility of the analytical protocol is also tested through chromium(VI) detection in environmental samples.

  13. Biomonitoring for chromium and arsenic in timber treatment plant workers exposed to CCA wood Preservatives.

    Science.gov (United States)

    Cocker, J; Morton, J; Warren, N; Wheeler, J P; Garrod, A N I

    2006-07-01

    This study reports a survey of occupational exposure to copper chrome arsenic (CCA) based wood preservatives during vacuum pressure timber impregnation. The survey involved biological monitoring based on analysis of chromium and arsenic in urine samples collected from UK workers. The aim of the study was to determine the extent of occupational exposure to arsenic and chromium in the UK timber treatment industry. The objectives were to collect and analyse urine samples from as many workers as possible, where CCA wood preservatives might be used, at 6 monthly intervals for 2 years. In addition, to investigate day-to-day variations in urinary excretion of chrome and arsenic by collecting and analysing three samples a week for 3 weeks in subsets of workers and controls (people not occupationally exposed). All urine samples were analysed for chromium and inorganic arsenic. To investigate any residual interference every sample was accompanied by a short questionnaire about recent consumption of seafood and smoking. The analytical methods for arsenic used a hydride generation technique to reduce interference from dietary sources of arsenic and also a technique that would measure total arsenic concentration in urine. The main findings show that workers exposed to CCA wood preservatives have concentrations of inorganic arsenic and chromium in urine that are significantly higher than those from non-occupationally exposed people but below biological monitoring guidance values that would indicate inhalation exposure at UK occupational exposure limits for chromium and arsenic. The effects of consumption of seafood on urinary arsenic were not significant using the hydride generation method for inorganic arsenic but were significant if 'total' arsenic was measured. The 'total' arsenic method could not distinguish CCA workers from controls and is clearly unsuitable for assessment of occupational exposure to arsenic. There was a significant increase in the urinary concentration of

  14. 77 FR 6627 - National Emission Standards for Hazardous Air Pollutant Emissions: Hard and Decorative Chromium...

    Science.gov (United States)

    2012-02-08

    ... aluminum to provide resistance to corrosion. The chromium anodizing process is used to coat aircraft parts... Hazardous Air Pollutant Emissions: Hard and Decorative Chromium Electroplating and Chromium Anodizing Tanks... Pollutant Emissions: Hard and Decorative Chromium Electroplating and Chromium Anodizing Tanks; and...

  15. CHROMIUM INDUCED CYTOTOXICITY IN BLACKGRAM (VIGNA MUNGO L.

    Directory of Open Access Journals (Sweden)

    A. Chidambaram ، P. Sundaramoorthy ، A. Murugan ، K. Sankar Ganesh ، L. Baskaran

    2009-01-01

    Full Text Available Chromium is known to be highly toxic to biological systems. This study was designed to determine the mutagenic effects of different concentrations (0, 10, 25, 50, 100 and 200 mg/L of hexavalent chromium on root tip cells of blackgram (Vigna mungo L. Hepper. The blackgram seeds were equi-spacially arranged in sterilized petriplates lined with filter paper and they were treated with different concentrations of chromium solution. In germination studies, the morphological growth parameters such as germination percentage, root length, shoot length fresh weight and dry weight of blackgram seedlings were decreased with increasing dose of chromium concentrations. No germination of blackgram seeds was recorded at 300mg/l chromium concentration. Chromosome aberration assay was used to determine the mitotic indices and rate of chromosome aberration in blackgram root tip cells due to chromium treatment. The results showed that the mitotic indices were complicated due to different concentrations of chromium. However, the increase in chromium concentration has led to a gradual increase in the percentage of chromosomal aberration and mitotic index. The chromosome length, absolute chromosome length and average chromosome lengths were gradually found to decrease. There was no considerable change in 2n number of chromosome with the increase in chromium concentrations. It is concluded that the hexavalent chromium has significant mutagenic effect on the root tip cells of blackgram.

  16. Influences of copper on solidification structure and hardening behavior of high chromium cast irons

    Institute of Scientific and Technical Information of China (English)

    WANG Jun; XIONG Ji; FAN Hong-yuan; SHEN Bao-luo; GAO Sheng-ji

    2008-01-01

    The influences of copper on microstructure and the hardening behavior of high chromium cast irons subjected to sub-critical treatment were investigated.The results show that the mierostructure of the as-cast high chromium cast irons consists of retained austenite,martensite and M7 C3 type eutectic carbide.When copper is added into high chromium cast irons,austenite and carbide contents are increased.The increased addition of copper content from 0%to 1.84%leads to the increase of austenite and carbide from 15.9%and 20.0% to 61.0%and 35.5%,respectively.In the process of sub-critical treatment,the retained austenite in the matrix can be precipitated into secondary carbides and then transforms into martensite in cooling process,which causes the secondary hardening of the alloy under sub-critical treatment.High chromium cast irons containing copper in sub-critical treatment appear the second hardening curve peak due to the precipitation of copper from supersaturated matrix.

  17. Hexavalent chromium reduction by aerobic heterotrophic bacteria indigenous to chromite mine overburden

    Directory of Open Access Journals (Sweden)

    Dey Satarupa

    2013-01-01

    Full Text Available Microbiological analysis of overburden samples collected from chromite mining areas of Orissa, India revealed that they are rich in microbial density as well as diversity and dominated by Gramnegative (58% bacteria. The phenotypically distinguishable bacterial isolates (130 showed wide degree of tolerance to chromium (2-8 mM when tested in peptone yeast extract glucose agar medium. Isolates (92 tolerating 2 mM chromium exhibited different degrees of Cr+6 reducing activity in chemically defined Vogel Bonner (VB broth and complex KSC medium. Three potent isolates, two belonging to Arthrobacter spp. and one to Pseudomonas sp. were able to reduce more than 50 and 80% of 2 mM chromium in defined and complex media respectively. Along with Cr+6 (MIC 8.6-17.8 mM, the isolates showed tolerance to Ni+2, Fe+3, Cu+2 and Co+2 but were extremely sensitive to Hg+2 followed by Cd+2, Mn+2 and Zn+2. In addition, they were resistant to antibiotics like penicillin, methicillin, ampicillin, neomycin and polymyxin B. During growth under shake-flask conditions, Arthrobacter SUK 1201 and SUK 1205 showed 100% reduction of 2 mM Cr+6 in KSC medium with simultaneous formation of insoluble precipitates of chromium salts. Both the isolates were also equally capable of completely reducing the Cr+6 present in mine seepage when grown in mine seepage supplemented with VB concentrate.

  18. Selective Leaching of Chromium from Hanford Tank Sludge 241-U-108

    Energy Technology Data Exchange (ETDEWEB)

    Rapko, Brian M.; Vienna, John D.

    2002-09-09

    This study evaluated the oxidants permanganate, MnO4-, and peroxynitrite, ONOO-, as selective chromium-leaching agents from washed 241-U-108 tank sludge under varying conditions of hydroxide concentration, temperature, and time. The mass changes and final sludge compositions were evaluated using glass-property models to ascertain the relative impacts of the various oxidative alkaline leach conditions on the amount of borosilicate glass required to immobilize a given amount of washed 241-U-108 Hanford tank sludge. Only permanganate leaching removes sufficient chromium to make the chromium concentration in the oxidatively alkaline leached solids non-limiting. In the absence of added oxidants, continued washing or caustic leaching have no beneficial effects. Peroxynitrite addition reduces the amount of glass required to immobilize a given amount of washed 241-U-108 tank sludge by approximately a factor of two. Depending on the leach conditions and the exact chromium concentration limits, contact with alkaline permanganate solutions reduces the amount of immobilized high-level waste glass by a factor of 10 to 30.

  19. Chromium Mobilization by Microbially-Driven Iron and Manganese Redox Cycling

    Science.gov (United States)

    Garcia Arredondo, M.; Hausladen, D.; Ying, S.; Fendorf, S. E.

    2014-12-01

    Chromium, a naturally occurring contaminant, poses a significant threat to California groundwater quality when ultramafic rocks weather leaving Cr-enriched serpentine soils. Benign and of limited solubility, Cr(III) can oxidize into soluble and carcinogenic Cr(VI). Under most environmental conditions, Mn-oxides are the principal oxidant of Cr(III). Here we investigate Cr(III) oxidation by both abiotically synthesized birnessite and biogenically produced Mn-oxides. Further, we explore chromium dynamics within artificial soil aggregates composed of Cr(OH)3- and Cr0.25Fe0.75(OH)3-coated quartz grains surrounded by aerated solute flow. Abiotic aggregates contained synthetic birnessite, while biotic aggregates were inoculated with Leptothrix cholodnii, a manganese-oxidizing bacterium, and Shewanella putrefaciens, an iron-reducing bacterium. Results show aqueous Cr(VI) concentrations scaling with Cr-mineral solubility. When Leptothrix sp.-inoculated Cr(III),Fe(III)-aggregates are supplied with aqueous Mn(II), Mn-oxides precipitate in the aerobic aggregate. Cr(VI) production occurs similar to that via synthetic birnessite. With the addition of Shewanella sp., coupled biotic and abiotic processes occur causing the reduction, and subsequent immobilization, of chromium by microbial metabolites (e.g., Fe(II)). This study shows the importance of microbial community composition on chromium dynamics within diffusion-limited zones, and suggests the potential for biological immobilization of Cr even in the presence of Mn-oxidizing bacteria.

  20. Interactions of chromium with microorganisms and plants.

    Science.gov (United States)

    Cervantes, C; Campos-García, J; Devars, S; Gutiérrez-Corona, F; Loza-Tavera, H; Torres-Guzmán, J C; Moreno-Sánchez, R

    2001-05-01

    Chromium is a highly toxic non-essential metal for microorganisms and plants. Due to its widespread industrial use, chromium (Cr) has become a serious pollutant in diverse environmental settings. The hexavalent form of the metal, Cr(VI), is considered a more toxic species than the relatively innocuous and less mobile Cr(III) form. The presence of Cr in the environment has selected microbial and plant variants able to tolerate high levels of Cr compounds. The diverse Cr-resistance mechanisms displayed by microorganisms, and probably by plants, include biosorption, diminished accumulation, precipitation, reduction of Cr(VI) to Cr(III), and chromate efflux. Some of these systems have been proposed as potential biotechnological tools for the bioremediation of Cr pollution. In this review we summarize the interactions of bacteria, algae, fungi and plants with Cr and its compounds.

  1. Effect of polyethylene glycol on electrochemically deposited trivalent chromium layers

    Institute of Scientific and Technical Information of China (English)

    Joo-Yul LEE; Man KIM; Sik-Chol KWON

    2009-01-01

    The structural characteristics of the trivalent chromium deposits and their interfacial behavior in the plating solution with and without polyethylene glycol molecules were observed by using various electrochemical methods such as cyclic voltammetry, open circuit potential transition, electrochemical impedance spectroscopy, scanning electron microscopy and X-ray photoelectron spectrometry. It is shown that the polyethylene glycol molecules make the reductive current density lower in the trivalent chromium plating system and promote a hydrogen evolution reaction through their adsorption on the electrode surface. And the trivalent chromium layer formed from the polyethylene glycol-containing solution has somewhat higher density of cracks on its surface and results in a lower film resistance, lower polarization resistance, and higher capacitance in a corrosive atmosphere. It is also revealed that the formation of chromium carbide layer is facilitated in the presence of polyethylene glycol, which means easier electrochemical codeposition of chromium and carbon, not single chromium deposition.

  2. Speciation and recovery of chromium from chromite ore processing residues.

    Science.gov (United States)

    Sreeram, K J; Ramasami, T

    2001-10-01

    The processing of chromite ore is associated with the generation of large quantities of solid wastes containing chromium, which have been disposed of as landfill for many years. The mobilization and operational speciation of chromium contained in soils contaminated with metal salts are important in terms of the environment. Several methods have been employed for the extraction and recovery of solid wastes. Chromium contained in contaminated soils and solid wastes can be categorized as exchangeable, oxidizable, carbonate-bound, reducible and residual. The results from this study indicate a need for efficient leaching methodologies in chromite ore processing plants to decrease the non-detrital fractions of chromium in the residue. Aggressive methodologies are required to recover chromium from the detrital fractions. The potential benefits of employing sodium peroxide for the complete recovery of chromium from chromite residue have been demonstrated, and the need to ensure the safety of the process has been emphasized.

  3. Chromium Toxicity: Reductive Enzymes in Humans.

    Science.gov (United States)

    2007-11-02

    internal organs (e.g. lungs, liver, kidneys) [24,27,64], pulmonary fibrosis and chronic bronchitis [2], skin ulcers and allergic dermatitis [2], and...cross the skin [2] and are readily transported across cell membranes [18] via an anion carrier [6]. Cr compounds are also mutagenic [67], and the bulk of...reduced nicotinamide adenine dinucleotide phosphate-cytochrome P450 oxidoreductase- dependent chromium(VI) reduction. Analyst 120:935-938. 42. Miura, A

  4. Dimensionally Controlled Lithiation of Chromium Oxide

    Energy Technology Data Exchange (ETDEWEB)

    Fister, Tim T. [Argonne National Lab. (ANL), Argonne, IL (United States); Hu, Xianyi [Northwestern Univ., Evanston, IL (United States); Esbenshade, Jennifer [Univ. of Illinois, Urbana-Champaign, IL (United States); Chen, Xiao [Northwestern Univ., Evanston, IL (United States); Wu, Jinsong [Northwestern Univ., Evanston, IL (United States); Dravid, Vinayak [Northwestern Univ., Evanston, IL (United States); Bedzyk, Michael [Northwestern Univ., Evanston, IL (United States); Long, Brandon [Argonne National Lab. (ANL), Argonne, IL (United States); Gewirth, Andrew A. [Univ. of Illinois, Urbana-Champaign, IL (United States); Shi, Bing [Argonne National Lab. (ANL), Argonne, IL (United States); Schlepütz, Christian M. [Argonne National Lab. (ANL), Argonne, IL (United States); Fenter, Paul [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-01-12

    Oxide conversion reactions are an alternative approach for high capacity lithium ion batteries but are known to suffer from structural irreversibility associated with the phase separation and reconstitution of reduced metal species and Li2O. In particular, the morphology of the reduced metal species is thought to play a critical role in the electrochemical properties of a conversion material. Here we use a model electrode with alternating layers of chromium and chromium oxide to better understand and control these phase changes in real-time and at molecular length scales. Despite lacking crystallinity at the atomic scale, this superstructure is observed (with X-ray reflectivity, XR) to lithiate and delithiate in a purely one-dimensional manner, preserving the layered structure. The XR data show that the metal layers act as nucleation sites for the reduction of chromium in the conversion reaction. Irreversibility during delithiation is due to the formation of a ternary phase, LiCrO2, which can be further delithiated at higher potentials. The results reveal that the combination of confining lithiation to nanoscale sheets of Li2O and the availability of reaction sites in the metal layers in the layered structure is a strategy for improving the reversibility and mass transport properties that can be used in a wide range of conversion materials.

  5. Processes affecting the remediation of chromium-contaminated sites.

    OpenAIRE

    Palmer, C.D.; Wittbrodt, P R

    1991-01-01

    The remediation of chromium-contaminated sites requires knowledge of the processes that control the migration and transformation of chromium. Advection, dispersion, and diffusion are physical processes affecting the rate at which contaminants can migrate in the subsurface. Heterogeneity is an important factor that affects the contribution of each of these mechanisms to the migration of chromium-laden waters. Redox reactions, chemical speciation, adsorption/desorption phenomena, and precipitat...

  6. AQUIFER TESTING AND REBOUND STUDY IN SUPPORT OF THE 100-H DEEP CHROMIUM INVESTIGATION

    Energy Technology Data Exchange (ETDEWEB)

    SMOOT JL

    2010-11-05

    The 100-HR-3 Groundwater Operable Unit (OU) second Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) 5-year review (DOEIRL-2006-20, The Second CERCLA Five-Year Review Report for the Hanford Site) set a milestone to conduct an investigation of deep hexavalent chromium contamination in the sediments of the Ringold upper mud (RUM) unit, which underlies the unconfined aquifer in the 100-H Area. The 5-year review noted that groundwater samples from one deep well extending below the aquitard (i.e., RUM) exceeded both the groundwater standard of 48 parts per billion (ppb) (Ecology Publication 94-06, Model Toxics Control Act Cleanup Statute and Regulation) and the federal drinking water standard of 100 {mu}g/L for hexavalent chromium. The extent of hexavalent chromium contamination in this zone is not well understood. Action 12-1 from the 5-year review is to perform additional characterization of the aquifer below the initial aquitard. Field characterization and aquifer testing were performed in the Hanford Site's 100-H Area to address this milestone. The aquifer tests were conducted to gather data to answer several fundamental questions regarding the presence of the hexavalent chromium in the deep sediments of the RUM and to determine the extent and magnitude of deeper contamination. The pumping tests were performed in accordance with the Description of Work for Aquifer Testing in Support of the 100-H Deep Chromium Investigation (SGW-41302). The specific objectives for the series of tests were as follows: (1) Evaluate the sustainable production of the subject wells using step-drawdown and constant-rate pumping tests. (2) Collect water-level data to evaluate the degree of hydraulic connection between the RUM and the unconfined (upper) aquifer (natural or induced along the well casing). (3) Evaluate the hydraulic properties of a confined permeable layer within the RUM.; (4) Collect time-series groundwater samples during testing to

  7. Stabilization and solidification of chromium-contaminated soil

    Energy Technology Data Exchange (ETDEWEB)

    Cherne, C.A.; Thomson, B.M. [Univ. of New Mexico, Albuquerque, NM (United States). Civil Engineering Dept.; Conway, R. [Sandia National Labs., Albuquerque, NM (United States)

    1997-11-01

    Chromium-contaminated soil is a common environmental problem in the United States as a result of numerous industrial processes involving chromium. Hexavalent chromium [Cr(VI)] is the species of most concern because of its toxicity and mobility in groundwater. One method of diminishing the environmental impact of chromium is to reduce it to a trivalent oxidation state [Cr(III)], in which it is relatively insoluble and nontoxic. This study investigated a stabilization and solidification process to minimize the chromium concentration in the Toxicity Characteristic Leaching Procedure (TCLP) extract and to produce a solidified waste form with a compressive strength in the range of 150 to 300 pounds per square inch (psi). To minimize the chromium in the TCLP extract, the chromium had to be reduced to the trivalent oxidation state. The average used in this study was an alluvium contaminated with chromic and sulfuric acid solutions. The chromium concentration in the in the in situ soil was 1212 milligrams per kilogram (mg/kg) total chromium and 275 mg/kg Cr(VI). The effectiveness of iron, ferrous sulfate to reduce Cr(VI) was tested in batch experiments.

  8. Chromium poisoning in (La,Sr)MnO3 cathode: Three-dimensional simulation of a solid oxide fuel cell

    Science.gov (United States)

    Miyoshi, Kota; Iwai, Hiroshi; Kishimoto, Masashi; Saito, Motohiro; Yoshida, Hideo

    2016-09-01

    A three-dimensional numerical model of a single solid oxide fuel cell (SOFC) considering chromium poisoning on the cathode side has been developed to investigate the evolution of the SOFC performance over long-term operation. The degradation model applied in the simulation describes the loss of the cathode electrochemical activity as a decrease in the active triple-phase boundary (TPB) length. The calculations are conducted for two types of cell: lanthanum strontium manganite (LSM)/yttria-stabilized zirconia (YSZ)/Ni-YSZ and LSM-YSZ/YSZ/Ni-YSZ. Their electrode microstructures are acquired by imaging with a focused ion beam scanning-electron microscope (FIB-SEM). The simulation results qualitatively reproduce the trends of chromium poisoning reported in the literature. It has been revealed that the performance degradation by chromium is primarily due to an increase in the cathode activation overpotential. In addition, in the LSM-YSZ composite cathode, TPBs in the vicinity of the cathode-electrolyte interface preferentially deteriorate, shifting the active reaction site towards the cathode surface. This also results in an increase in the cathode ohmic loss associated with oxide ion conduction through the YSZ phase. The effects of the cell temperature, the partial pressure of steam at the chromium source, the cathode microstructure, and the cathode thickness on chromium poisoning are also discussed.

  9. Novel high chromium containing braze filler metals for heat exchanger applications

    Energy Technology Data Exchange (ETDEWEB)

    Rangaswamy, S.; Fortuna, D. [Sulzer Metco, Troy (United States)

    2007-07-01

    A new family of boron-free, high chromium containing braze filler metal compositions were developed (Amdry 105, Amdry 108, Amdry 805). Filler metal properties including metallurgical phases, melting range, flow, corrosion resistance and high temperature oxidation resistance are reported. Additionally, the technical and economical advantages of using these new filler metals in fabricating flat plate type of heat exchangers and metallic catalytic converters is discussed. (orig.)

  10. Biosorption and removal of chromium from water by using moringa seed cake (Moringa oleifera Lam.)

    OpenAIRE

    Ana Paula Meneghel; Affonso Celso Gonçalves Jr.; Leonardo Strey; Fernanda Rubio; Daniel Schwantes; Juliana Casarin

    2013-01-01

    This study evaluated the adsorption capacity of chromium from contaminated aqueous solutions by using Moringa oleifera Lam. seeds. Parameters such as solution pH, adsorbent mass, contact time between solution and adsorbent, isotherms, thermodynamic, kinetics, and desorption were evaluated. The maximum adsorption capacity (Qm) calculated to be 3.191 mg g-1 for the biosorbent. Activated carbon was used for comparison purposes in addition to the biosorbent. The best fit was obtained by the Langm...

  11. Determination of Trace Amounts of Chromium(III) in Water Samples Using Online Flow Injection Catalytic Spectrophotometry

    Science.gov (United States)

    Zhao, Z. X.; Zhang, X. S.

    2017-01-01

    A new online flow injection spectrophotometric method for the determination of trivalent chromium was developed. This method is based on the property of trivalent chromium to be a catalyst for the oxidation of Indigo Carmine (IC) with potassium periodate and to lose its color in the presence of ethylenediaminetetraacetic acid and sodium tripolyphosphate. It was shown that Tween-20 serves as an additional accelerator of the catalytic oxidation. The linear dynamic range of the determination of Cr(III) was 1-40.0 μg/L, while the limit of detection was 0.05 μg/L. The correlation coefficient r was 0.998, while the relative standard deviation for 5 μg/L of the Cr(III) solution was 3.83%. The feasibility of this method was checked by its application to trivalent chromium determination in real water samples.

  12. Isolation of a hexanuclear chromium cluster with a tetrahedral hydridic core and its catalytic behavior for ethylene oligomerization.

    Science.gov (United States)

    Alzamly, Ahmed; Gambarotta, Sandro; Korobkov, Ilia; Murugesu, Muralee; Le Roy, Jennifer J H; Budzelaar, Peter H M

    2014-06-16

    A chromium complex [2-(NHCH2PPh2)C5H4N]CrCl3·THF2 (1) of the ligand PyNHCH2PPh2 has been synthesized, characterized, and examined for its catalytic behavior toward ethylene oligomerization. When complex 1 was treated with (i-Bu)3Al, an unprecedented divalent polyhydride chromium cluster μ,κ(1),κ(2),κ(3)-N,N,P-{[2-(NCH2PPh2)C5H4N]Cr(μ-H)}4[(μ-Cl)Cr(μ-Cl)Al(i-Bu)2Cl]2 (2) was obtained. The complex contains a Cr4H4 core, which is expected to be diamagnetic, and which remains coordinated to two additional divalent high-spin Cr atoms via bridging interactions. Two aluminate residues remain bonded to the peripheral chromium atoms. The structure, magnetism, and electronic configuration are herein discussed.

  13. Diffusion of hexavalent chromium in chromium-containing slag as affected by microbial detoxification.

    Science.gov (United States)

    Wang, Yunyan; Yang, Zhihui; Chai, Liyuan; Zhao, Kun

    2009-09-30

    An electrochemical method was used to determine the diffusion coefficient of chromium(VI) in chromium-containing slag. A slag plate was prepared from the original slag or the detoxified slag by Achromobacter sp. CH-1. The results revealed that the apparent diffusion coefficient of Cr(VI) was 4.4 x 10(-9)m(2)s(-1) in original slag and 2.62 x 10(-8)m(2)s(-1) in detoxified slag. The results implied that detoxification of chromium-containing slag by Achromobacter sp. CH-1 could enhance Cr(VI) release. Meanwhile, the results of laboratory experiment showed that the residual total Cr(VI) in slag decreased from an initial value of 6.8 mg g(-1) to 0.338 mg g(-1) at the end of the detoxification process. The Cr(VI) released from slag was also reduced by Achromobacter sp. CH-1 strain since water soluble Cr(VI) in the leachate was not detected after 4 days. Therefore, Achromobacter sp. CH-1 has potential application for the bio-detoxification of chromium-containing slag.

  14. Food additives

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/002435.htm Food additives To use the sharing features on this page, please enable JavaScript. Food additives are substances that become part of a food ...

  15. ALUMINUM AND CHROMIUM LEACHING WORKSHOP WHITEPAPER

    Energy Technology Data Exchange (ETDEWEB)

    McCabe, D; Jeff Pike, J; Bill Wilmarth, B

    2007-04-25

    A workshop was held on January 23-24, 2007 to discuss the status of processes to leach constituents from High Level Waste (HLW) sludges at the Hanford and Savannah River Sites. The objective of the workshop was to examine the needs and requirements for the HLW flowsheet for each site, discuss the status of knowledge of the leaching processes, communicate the research plans, and identify opportunities for synergy to address knowledge gaps. The purpose of leaching of non-radioactive constituents from the sludge waste is to reduce the burden of material that must be vitrified in the HLW melter systems, resulting in reduced HLW glass waste volume, reduced disposal costs, shorter process schedules, and higher facility throughput rates. The leaching process is estimated to reduce the operating life cycle of SRS by seven years and decrease the number of HLW canisters to be disposed in the Repository by 1000 [Gillam et al., 2006]. Comparably at Hanford, the aluminum and chromium leaching processes are estimated to reduce the operating life cycle of the Waste Treatment Plant by 20 years and decrease the number of canisters to the Repository by 15,000-30,000 [Gilbert, 2007]. These leaching processes will save the Department of Energy (DOE) billions of dollars in clean up and disposal costs. The primary constituents targeted for removal by leaching are aluminum and chromium. It is desirable to have some aluminum in glass to improve its durability; however, too much aluminum can increase the sludge viscosity, glass viscosity, and reduce overall process throughput. Chromium leaching is necessary to prevent formation of crystalline compounds in the glass, but is only needed at Hanford because of differences in the sludge waste chemistry at the two sites. Improving glass formulations to increase tolerance of aluminum and chromium is another approach to decrease HLW glass volume. It is likely that an optimum condition can be found by both performing leaching and improving

  16. Safety, absorption, and antioxidant effects of chromium histidine

    Science.gov (United States)

    Supplemental chromium has been shown to be involved in the alleviation of the metabolic syndrome, glucose intolerance, polycystic ovary syndrome, depression, excess body fat, and gestational, steroid-induced, and type 2 diabetes. Chromium amino acid complexes that contained histidine displayed cons...

  17. Mechanisms of bacterial resistance to chromium compounds.

    Science.gov (United States)

    Ramírez-Díaz, Martha I; Díaz-Pérez, César; Vargas, Eréndira; Riveros-Rosas, Héctor; Campos-García, Jesús; Cervantes, Carlos

    2008-06-01

    Chromium is a non-essential and well-known toxic metal for microorganisms and plants. The widespread industrial use of this heavy metal has caused it to be considered as a serious environmental pollutant. Chromium exists in nature as two main species, the trivalent form, Cr(III), which is relatively innocuous, and the hexavalent form, Cr(VI), considered a more toxic species. At the intracellular level, however, Cr(III) seems to be responsible for most toxic effects of chromium. Cr(VI) is usually present as the oxyanion chromate. Inhibition of sulfate membrane transport and oxidative damage to biomolecules are associated with the toxic effects of chromate in bacteria. Several bacterial mechanisms of resistance to chromate have been reported. The best characterized mechanisms comprise efflux of chromate ions from the cell cytoplasm and reduction of Cr(VI) to Cr(III). Chromate efflux by the ChrA transporter has been established in Pseudomonas aeruginosa and Cupriavidus metallidurans (formerly Alcaligenes eutrophus) and consists of an energy-dependent process driven by the membrane potential. The CHR protein family, which includes putative ChrA orthologs, currently contains about 135 sequences from all three domains of life. Chromate reduction is carried out by chromate reductases from diverse bacterial species generating Cr(III) that may be detoxified by other mechanisms. Most characterized enzymes belong to the widespread NAD(P)H-dependent flavoprotein family of reductases. Several examples of bacterial systems protecting from the oxidative stress caused by chromate have been described. Other mechanisms of bacterial resistance to chromate involve the expression of components of the machinery for repair of DNA damage, and systems related to the homeostasis of iron and sulfur.

  18. Observational Approach to Chromium Site Remediation - 13266

    Energy Technology Data Exchange (ETDEWEB)

    Scott Myers, R. [Washington Closure Hanford, 2620 Fermi, Richland, Washington 99354 (United States)

    2013-07-01

    Production reactors at the U.S. Department of Energy's (DOE) Hanford Site in Richland, Washington, required massive quantities of water for reactor cooling and material processing. To reduce corrosion and the build-up of scale in pipelines and cooling systems, sodium dichromate was added to the water feedstock. Spills and other releases at the makeup facilities, as well as leaks from miles of pipelines, have led to numerous areas with chromium-contaminated soil and groundwater, threatening fish populations in the nearby Columbia River. Pump-and-treat systems have been installed to remove chromium from the groundwater, but significant contamination remain in the soil column and poses a continuing threat to groundwater and the Columbia River. Washington Closure Hanford, DOE, and regulators are working on a team approach that implements the observational approach, a strategy for effectively dealing with the uncertainties inherent in subsurface conditions. Remediation of large, complex waste sites at a federal facility is a daunting effort. It is particularly difficult to perform the work in an environment of rapid response to changing field and contamination conditions. The observational approach, developed by geotechnical engineers to accommodate the inherent uncertainties in subsurface conditions, is a powerful and appropriate method for site remediation. It offers a structured means of quickly moving into full remediation and responding to the variations and changing conditions inherent in waste site cleanups. A number of significant factors, however, complicate the application of the observational approach for chromium site remediation. Conceptual models of contamination and site conditions are difficult to establish and get consensus on. Mid-stream revisions to the design of large excavations are time-consuming and costly. And regulatory constraints and contract performance incentives can be impediments to the flexible responses required under the

  19. Atom Lithography with a Chromium Atomic Beam

    Institute of Scientific and Technical Information of China (English)

    ZHANG Wen-Tao; LI Tong-Bao

    2006-01-01

    @@ Direct write atom lithography is a new technique in which resonant light is used to pattern an atomic beam and the nanostructures are formed when the atoms deposit on the substrate. We design an experiment setup to fabricate chromium nanolines by depositing an atomic beam of 52 Cr through an off-resonant laser standing wave with the wavelength of 425.55 nm onto a silicon substrate. The resulting nanolines exhibit a period of 215 ± 3 nm with height of 1 nm.

  20. The fate of chromium during tropical weathering

    DEFF Research Database (Denmark)

    Berger, Alfons; Frei, Robert

    2014-01-01

    We performed a mineral, geochemical and Cr–Sr–Pb isotope study on a laterite profile developed on ca. 540 Ma old tonalitic bedrock in Madagascar with special emphasis on the behavior of chromium during tropical weathering. The observed strong depletions of Ca, Si, and P, and enrichment of Fe and Al......, in the soil, relative to bedrock and underlying saprolite, are the characteristic features pertinent to laterites. The enrichment of Fe in topsoil horizon can be correlated with enrichment of P, and the redox sensitive elements Mn and Cr, and indicates redistribution of these elements related to oxidation...

  1. Bioleaching of chromium from tannery sludge by indigenous Acidithiobacillus thiooxidans.

    Science.gov (United States)

    Wang, Yuan-Shan; Pan, Zhi-Yan; Lang, Jian-Min; Xu, Jian-Miao; Zheng, Yu-Guo

    2007-08-17

    Chromium in tannery sludge will cause serious environmental problems and is toxic to organisms. The acidophilic sulfur-oxidizing Acidithiobacillus thiooxidans can leach heavy metals form urban and industrial wastes. This study examined the ability of an indigenous sulfur-oxidizing A. thiooxidans to leach chromium from tannery sludge. The results showed that the pH of sludge mixture inoculated with the indigenous A. thiooxidans decreased to around 2.0 after 4 days. After 6 days incubation in shaking flasks at 30 degrees C and 160 rpm, up to 99% of chromium was solubilized from tannery sludge. When treated in a 2-l bubble column bioreactor for 5 days at 30 degrees C and aeration of 0.5 vvm, 99.7% of chromium was leached from tannery sludge. The results demonstrated that chromium in tannery sludge can be efficiently leached by the indigenous A. thiooxidans.

  2. The Theory for the Mechanism of Chromium Plating: The Theory for the Physical Characteristics of Chromium Plate

    Science.gov (United States)

    1947-01-01

    deposits arc pro- duced as the coll potential is successively raised. The sulfato ion "hus has an extremely important effect in the chromium plating...and sulfato iDU in the bath wore then used in an attempt to obtain more satisfactory hexagonal chromium deposits. The data obtained are summarUod

  3. Dissolution of chromium in sulfuric acid

    Directory of Open Access Journals (Sweden)

    J. P. POPIC

    2002-11-01

    Full Text Available By combining electrochemical corrosion rate measurements and spectrophotometric analysis of the electrolyte it was shown that at room temperature chromium dissolves in deaerated 0.1 M Na2SO4 + H2SO4 (pH 1 solution as Cr(II and Cr(III ions in he ratio Cr(II : Cr(III @ 7 : 1. This process was stable over 4 h without any detectable change. The total corrosion rate of chromium calculated from the analytical data is about 12 times higher, than that determined electrochemically by cathodic Tafel line extrapolation to the corrosion potential. This finding was confirmed by applying the weight-loss method for the determination of the corrosion rate. This enormous difference between these experimentally determined corrosion rates can be explained by the rather fast, “anomalous” dissolution process proposed by Kolotyrkin and coworkers (chemical reaction of Cr with H2O molecules occurring simultaneously with the electrochemical corrosion process.

  4. Electrochemical modification of chromium surfaces using 4-nitro- and4-fluorobenzenediazonium salts

    DEFF Research Database (Denmark)

    Hinge, Mogens; Cecatto, Marcel; Kingshott, Peter;

    2009-01-01

    Chromium surfaces can be electrografted with organic surface films using 4-nitro- or 4-fluorobenzenediazonium salts, despite the fact that the surfaces are covered with a protective chromium oxide layer......Chromium surfaces can be electrografted with organic surface films using 4-nitro- or 4-fluorobenzenediazonium salts, despite the fact that the surfaces are covered with a protective chromium oxide layer...

  5. Standard Specification for Pressure Consolidated Powder Metallurgy Iron-Nickel-Chromium-Molybdenum (UNS N08367), Nickel-Chromium-Molybdenum-Columbium (Nb) (UNS N06625), Nickel-Chromium-Iron Alloys (UNS N06600 and N06690), and Nickel-Chromium-Iron-Columbium-Molybdenum (UNS N07718) Alloy Pipe Flanges, Fittings, Valves, and Parts

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2015-01-01

    Standard Specification for Pressure Consolidated Powder Metallurgy Iron-Nickel-Chromium-Molybdenum (UNS N08367), Nickel-Chromium-Molybdenum-Columbium (Nb) (UNS N06625), Nickel-Chromium-Iron Alloys (UNS N06600 and N06690), and Nickel-Chromium-Iron-Columbium-Molybdenum (UNS N07718) Alloy Pipe Flanges, Fittings, Valves, and Parts

  6. Chromium supplementation in patients with type 2 diabetes and high risk of type 2 diabetes: a meta-analysis of randomized controlled trials

    Directory of Open Access Journals (Sweden)

    Ismael San Mauro Martín

    Full Text Available Introduction: Chromium is an essential trace mineral for carbohydrate and lipid metabolism, which is currently prescribed to control diabetes mellitus. Results of previous systematic reviews and meta-analyses of chromium supplementation and metabolic profiles in diabetes have been inconsistent. Aim: The objective of this meta-analysis was to assess the effects on metabolic profiles and safety of chromium supplementation in type 2 diabetes mellitus and cholesterol. Methods: Literature searches in PubMed, Scopus and Web of Science were made by use of related terms-keywords and randomized clinical trials during the period of 2000-2014. Results: Thirteen trials fulfilled the inclusion criteria and were included in this systematic review. Total doses of Cr supplementation and brewer's yeast ranged from 42 to 1,000 µg/day, and duration of supplementation ranged from 30 to 120 days. The analysis indicated that there was a significant effect of chromium supplementation in diabetics on fasting plasma glucose with a weighted average effect size of -29.26 mg/dL, p = 0.01, CI 95% = -52.4 to -6.09; and on total cholesterol with a weighted average effect size of -6.7 mg/dL, p = 0.01, CI 95% = -11.88 to -1.53. Conclusions: The available evidence suggests favourable effects of chromium supplementation on glycaemic control in patients with diabetes. Chromium supplementation may additionally improve total cholesterol levels.

  7. Workshop on effects of chromium coating on Nb{sub 3}Sn superconductor strand: Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    1994-04-12

    This report discusses the following topics: Chromium coating on superconductor strand -- an overview; technology of chromium plating; comparison of wires plated by different platers; search for chromium in copper; strand manufactures` presentations; chromium plating at the Lawrence Livermore National Laboratory; a first look at a chromium plating process development project tailored for T.P.X. and I.T.E.R. strand; and influence of chromium diffusion and related phenomena on the reference ratios of bare and chromium plated Nb{sub 3}Sn strand.

  8. Bioavailability of a potato chromium complex to the laboratory rat

    Energy Technology Data Exchange (ETDEWEB)

    Gilbert, H.K.

    1985-01-01

    Research objectives were to study the effect of food source, preparation method and chemical form on bioavailability of chromium. Chromium concentration in potatoes was determined and tubers labeled either intrinsically or extrinsically with radioactive chromate. A labeled chromium complexes was isolated from preparations of raw, baked or fried potatoes and chromatographed on gel permeation media. Availability of the potato chromium complex to the rat was examined in three feeding studies. Animals were dosed with radioactive extrinsically or intrinsically labeled potato extract or with chromate. A labeled chromium complex was isolated from gastrointestinal contents of rats and chromatographed. Potato pulp and peel contained 1.63 and 2.70 ..mu..g Cr/g tissue respectively. True and apparent absorption from extrinsically labeled feedings were 33.4 +/- 4.7 and 29.8 +/- 11.2% respectively, and no differences existed between absorption from raw and cooked potatoes. Absorption from the extrinsic labeled potatoes differed significantly from absorption of inorganic chromatium. Apparent absorption of raw (11.1 +/- 7.9%) and cooked (-0.7 +/- 2.8%) intrinsically labeled feedings differed significantly. Absorption of inorganic chromium was 17.8% (true) and 11.5% (apparent). Examination of the chromium complex isolated from gastrointestinal tract contents showed enlargement of the complex in the stomach after consumption.

  9. Chromium Content in the Human Hip Joint Tissues

    Institute of Scientific and Technical Information of China (English)

    Barbara Brodziak-Dopiera; Jerzy Kwapuliski; Krzysztof Sobczyk; Danuta Wiechua

    2015-01-01

    Objective Chromium has many important functions in the human body. For the osseous tissue, its role has not been clearly defined. This study was aimed at determining chromium content in hip joint tissues. Methods A total of 91 hip joint samples were taken in this study, including 66 from females and 25 from males. The sample tissues were separated according to their anatomical parts. The chromium content was determined by the AAS method. The statistical analysis was performed with U Mann-Whitney's non-parametric test, P≤0.05. Results The overall chromium content in tissues of the hip joint in the study subjects was as follows:5.73 µg/g in the articular cartilage, 5.33 µg/g in the cortical bone, 17.86 µg/g in the cancellous bone, 5.95 µg/g in the fragment of the cancellous bone from the intertrochanteric region, and 1.28 µg/g in the joint capsule. The chromium contents were observed in 2 group patients, it was 7.04 µg/g in people with osteoarthritis and 12.59 µg/g in people with fractures. Conclusion The observed chromium content was highest in the cancellous bone and the lowest in the joint capsule. Chromium content was significantly different between the people with hip joint osteoarthritis and the people with femoral neck fractures.

  10. Mode of occurrence of chromium in four US coals

    Science.gov (United States)

    Huggins, Frank E.; Shah, N.; Huffman, G.P.; Kolker, A.; Crowley, S.; Palmer, C.A.; Finkelman, R.B.

    2000-01-01

    The mode of occurrence of chromium in three US bituminous coals and one US subbituminous has been examined using both X-ray absorption fine structure (XAFS) spectroscopy and a selective leaching protocol supplemented by scanning electron microscopy (SEM) and electron microprobe measurements. A synthesis of results from both methods indicates that chromium occurs principally in two forms in the bituminous coals: the major occurrence of chromium is associated with the macerals and is not readily leached by any reagent, whereas a second, lesser occurrence, which is leachable in hydrofluoric acid (HF), is associated with the clay mineral, illite. The former occurrence is believed to be a small particle oxyhydroxide phase (CrO(OH)). One coal also contained a small fraction (<5%) of the chromium in the form of a chromian magnetite, and the leaching protocol indicated the possibility of a similar small fraction of chromium in sulfide form in all three coals. There was little agreement between the two techniques on the mode of occurrence of chromium in the subbituminous coal; however, only a limited number of subbituminous coals have been analyzed by either technique. The chromium in all four coals was trivalent as no evidence was found for the Cr6+ oxidation state in any coal.

  11. Removal of chromium from tannery effluents by adsorption.

    Science.gov (United States)

    Fadali, O A; Magdy, Y H; Daifullah, A A M; Ebrahiem, E E; Nassar, M M

    2004-01-01

    Tannery effluent is characterized not only by heavy loads but also with toxic heavy metals especially chromium ions. Chromium is considered an important source of contamination due to large volume of exhaust liquid discharged and solid sludge produced. Details on adsorption studies were carried out using synthetic chromium salts (chromium chloride) as adsorbate, and cement kiln dust (a waste from white cement industry) as adsorbent. Equilibrium isotherms have been determined for the adsorption of chromium ions on cement kiln dust. Kinetic study provided that the adsorption process is diffusion controlled. The experimental results have been fitted using Freundlich, Langmuir, and Redlich Peterson isotherms. The maximum adsorption capacity of cement kiln dust was found to be 33 mg/g. Industrial tannery effluent (22-mg/L chromium and COD 952 mg/L) was also treated by cement dust. The treated effluent (using 20 g cement dust per 1 L) contains only 0.6 mg/L chromium and COD 200 mg/L.

  12. Chromium-induced membrane damage: protective role of ascorbic acid

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Importance of chromium as environmental toxicant is largely due to impact on the body to produce cellular toxicity. The impact of chromium and their supplementation with ascorbic acid was studied on plasma membrane of liver and kidney in male Wistar rats (80 - 100gbody weight). It has been observed that the intoxication with chromium ( i. p. ) at the dose of 0.8 mg/100g body weight per day for a period of 28 days causes significant increase in the level of cholesterol and decrease in the level of phospbolipid of both liver and kidney. The alkaline pbosphatase, total ATPase and Na + -K + -ATPase activities were significantly decreased in both liver and kidney after chromium treatment,except total ATPase activity of kidney. It is suggested that chromium exposure at the present dose and duration induce for the alterations of structure and function of both liver and kidney plasma membrane. Ascorbic acid ( i.p. at the dose of 0.5 mg,/100g body weight per day for period of 28 days) supplementation can reduce these structural changes in the plasma membrane of liver and kidney. But the functional changes can not be completely replenished by the ascorbic acid supplementation in response to chromium exposure. So it is also suggested that ascorbic acid (nutritional antioxidant) is useful free radical scavenger to restrain the chromium-induced membrane damage.

  13. AQUIFER TESTING AND REBOUND STUDY IN SUPPORT OF THE 100-H DEEP CHROMIUM INVESTIGATION

    Energy Technology Data Exchange (ETDEWEB)

    SMOOT JL

    2010-11-05

    The 100-HR-3 Groundwater Operable Unit (OU) second Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) 5-year review (DOEIRL-2006-20, The Second CERCLA Five-Year Review Report for the Hanford Site) set a milestone to conduct an investigation of deep hexavalent chromium contamination in the sediments of the Ringold upper mud (RUM) unit, which underlies the unconfined aquifer in the 100-H Area. The 5-year review noted that groundwater samples from one deep well extending below the aquitard (i.e., RUM) exceeded both the groundwater standard of 48 parts per billion (ppb) (Ecology Publication 94-06, Model Toxics Control Act Cleanup Statute and Regulation) and the federal drinking water standard of 100 {mu}g/L for hexavalent chromium. The extent of hexavalent chromium contamination in this zone is not well understood. Action 12-1 from the 5-year review is to perform additional characterization of the aquifer below the initial aquitard. Field characterization and aquifer testing were performed in the Hanford Site's 100-H Area to address this milestone. The aquifer tests were conducted to gather data to answer several fundamental questions regarding the presence of the hexavalent chromium in the deep sediments of the RUM and to determine the extent and magnitude of deeper contamination. The pumping tests were performed in accordance with the Description of Work for Aquifer Testing in Support of the 100-H Deep Chromium Investigation (SGW-41302). The specific objectives for the series of tests were as follows: (1) Evaluate the sustainable production of the subject wells using step-drawdown and constant-rate pumping tests. (2) Collect water-level data to evaluate the degree of hydraulic connection between the RUM and the unconfined (upper) aquifer (natural or induced along the well casing). (3) Evaluate the hydraulic properties of a confined permeable layer within the RUM.; (4) Collect time-series groundwater samples during testing to

  14. Use of adsorption using granular activated carbon (GAC) for the enhancement of removal of chromium from synthetic wastewater by electrocoagulation.

    Science.gov (United States)

    Vivek Narayanan, N; Ganesan, Mahesh

    2009-01-15

    The present work deals with removal of hexavalent chromium from synthetic effluents in a batch stirred electrocoagulation cell with iron-aluminium electrode pair coupled with adsorption using granular activated carbon (GAC). Several working parameters such as pH, current density, adsorbent concentration and operating time were studied in an attempt to achieve higher removal capacity. Results obtained with synthetic wastewater revealed that most effective removal capacities of chromium (VI) could be achieved when the initial pH was near 8. The removal of chromium (VI) during electrocoagulation, is due to the combined effect of chemical precipitation, coprecipitation, sweep coagulation and adsorption. In addition, increasing current density in a range of 6.7-26.7mA/cm2 and operating time from 20 to 100min enhanced the treatment rate to reduce metal ion concentration below admissible legal levels. The addition of GAC as adsorbent resulted in remarkable increase in the removal rate of chromium at lower current densities and operating time, than the conventional electrocoagulation process. The method was found to be highly efficient and relatively fast compared to existing conventional techniques.

  15. Spectroscopic analysis of chromium bioremediation products

    Science.gov (United States)

    Varadharajan, C.; Nico, P. S.; Yang, L.; Marcus, M. A.; Steefel, C.; Larsen, J. T.; Beller, H. R.; Brodie, E. L.

    2010-12-01

    Remediation of chromium contamination frequently involves reducing the toxic and soluble hexavalent form, Cr(VI), to the relatively harmless and mostly immobile trivalent state, Cr(III). The objective of this study is to identify the biogeochemical reactions that control in situ chromium reduction in the presence of different dominant electron acceptors, i.e., NO3-, Fe(III), and SO42-. It was hypothesized that indirect, abiotic reduction of Cr(VI) by reduced metabolic products [Fe(II) and sulfides] would dominate over direct enzymatic reduction by denitrifying, iron-reducing, or sulfate-reducing bacteria. It is further hypothesized that the enzymatic reduction of Cr(VI) would produce relatively pure chromium hydroxide precipitates, whereas indirect reduction would result in mixed Cr-Fe hydroxide solid phases. Flow-through columns containing homogenized sediments from the 100H site at Hanford, WA were subjected to nitrate-, sulfate- or iron-reducing conditions in the presence of 5 µM Cr(VI) and 5 mM lactate. Cr(VI) was depleted in the effluent solutions from the nitrate- and sulfate-reducing columns; however only a small amount of Cr(VI) was removed under iron-reducing conditions. Preliminary analysis of micro X-ray absorption spectra indicate that the untreated and iron-reducing column sediments contained pre-existing Cr in the form of primary minerals, e.g. chromite and/or Cr-bearing micas. However, there was an increase in the relative abundance of mixed-phase Cr-Fe hydroxides, i.e., Cr1-xFex(OH)3 in the nitrate- and sulfate-treated columns. A possible explanation for the observations is that the production of Fe(II) was enhanced under the nitrate- and sulfate- reducing conditions, and was most likely sulfide-driven in the latter case. The Fe(II) was subsequently available for reduction of Cr(VI) resulting in the mixed-phase precipitates. The results from the spectroscopic analysis support the hypothesis that Fe(II)-mediated Cr reduction prevails over direct

  16. Mutagenic and carcinogenic actions of chromium and its compounds.

    Science.gov (United States)

    Mamyrbaev, Arstan Abdramanovich; Dzharkenov, Timur Agataevich; Imangazina, Zina Amangalievna; Satybaldieva, Umit Abulkhairovna

    2015-05-01

    Numerous experimental observations have been made on microorganisms and culture of the cells of mammals as well as the accounting of the chromosomal aberrations in the bone marrow cells of the mammals and of human cells displayed that the chromium and its compounds possess a pronounced mutagenic effect. Translocation test, induction record of DNA damage and repair systems in the mammalian and human cells with greater precision proves the presence of the mutagenic effect of the chromium and its compounds, which in turn is dependent on dose and time of this metal intoxication. Chromium and its compounds have pronounced mutagenic effect, on increased admission to organism of mammals and protozoa.

  17. Microbial biotechnology for remediation of aquatic habitats polluted with chromium

    OpenAIRE

    Viorica Coşier; I. Valentin Petrescu-Mag

    2008-01-01

    Chromium may occur in nine different forms of oxidation ranging from ?II to +VI, with forms II, III and VI as the most commonly encountered. In Cluj county, chromium pollution dates well back in time and has caused important dysfunction to the mechanical-biological wastewater purification station of the city of Cluj (Coşier & Diţă 1996). The purpose of this study was to develop one microbial method able to reduce hexavalent chromium (mobile, permeable to cell membrane, carcinogenic and mutage...

  18. Microbial Diversity of Chromium-Contaminated Soils and Characterization of Six Chromium-Removing Bacteria

    Science.gov (United States)

    He, Zhiguo; Hu, Yuting; Yin, Zhen; Hu, Yuehua; Zhong, Hui

    2016-06-01

    Three soil samples obtained from different sites adjacent to a chromium slag heap in a steel alloy factory were taken to examine the effect of chromium contamination on soil bacterial diversity as determined by construction of 16S rDNA clone libraries and sequencing of selected clones based on restriction fragment length polymorphism (RFLP) analysis. Results revealed that Betaproteobacteria, Gammaproteobacteria, Firmicutes, and Alphaproteobacteria occurred in all three soil samples, although the three samples differed in their total diversity. Sample 1 had the highest microbial diversity covering 12 different classes, while Sample 3 had the lowest microbial diversity. Strains of six different species were successfully isolated, one of which was identified as Zobellella denitrificans. To our knowledge, this is the first report of a strain belonging to the genus Zobellella able to resist and reduce chromium. Among all isolates studied, Bacillus odysseyi YH2 exhibited the highest Cr(VI)-reducing capability, with a total removal of 23.5 % of an initial Cr(VI) concentration of 350 mg L-1.

  19. [Blood and urine chromium: compared values between chromium exposed workers and common people].

    Science.gov (United States)

    Provenzani, A; Verso, M G; Picciotto, D

    2008-01-01

    Aim of present study is the valutation and quantification of chromium in blood and urine. We compared 3 groups of persons formed by building workers, in particular masons, because cement contains potassium chromate that is dangerous for health, and by common people: urban population and outside the town population. In fact, exposure to CrVI risk is high for people who live near chromate industries. We maked a medical examination, blood and instrumental tests, chromium measuring in blood (recent exposure indicator) and urine (recent and previous indicator). Then we used statistical methods to estimate obtained values of blood and urine chromium among professional exposed people and common people. At the end we think that preventive measures in working environment reduced exposure to CrVI but environmental exposure (for example road dust from catalytic converter erosion, from brake lining erosion, cement dust and tobacco smoke), in the last years, has increased. So there are no difference between urban population and outside the town population and there are also no difference with professional exposed people for work prevention according to law in force, that let down professional risk using safe limits.

  20. Chromium accumulation, microorganism population and enzyme activities in soils around chromium-containing slag heap of steel alloy factory

    Institute of Scientific and Technical Information of China (English)

    HUANG Shun-hong; PENG Bing; YANG Zhi-hui; CHAI Li-yuan; ZHOU Li-cheng

    2009-01-01

    The environmental risk of chromium pollution is pronounced in soils adjacent to chromate industry. It is important to investigate the functioning of soil microorganisms in ecosystems exposed to long-term contamination by chromium. 45 soil samples obtained from different places of the slag heap in a steel alloy factory were analyzed for chromium contamination level and its effect on soil microorganisms and enzyme activities. The results show that the average concentrations of total Cr in the soil under the slag heap, adjacent to the slag heap and outside the factory exceed the threshold of Secondary Environmental Quality Standard for Soil in China by 354%, 540% and 184%, respectively, and are 15, 21 and 9 times higher than the local background value, respectively. Elevated chromium loadings result in changes in the activity of the soil microbe, as indicated by the negative correlations between soil microbial population and chromium contents. Dehydrogenase activity is greatly depressed by chromium in the soil. The results imply that dehydrogenase activity can be used as an indicator for the chromium pollution level in the area of the steel alloy factory.

  1. Possible adverse effect of chromium in occupational exposure of tannery workers.

    Science.gov (United States)

    Kornhauser, Carlos; Wróbel, Katarzyna; Wróbel, Kazimierz; Malacara, Juan Manuel; Nava, Laura Eugenia; Gómez, Leobardo; González, Rita

    2002-04-01

    Our aim was to investigate the adverse effects of occupational exposure to trivalent chromium. We measured chromium and iron levels in serum and urine and hemoglobin levels in tannery workers and unexposed persons. We studied three groups of subjects. Group 1 included 15 non-smoking male tannery workers highly exposed to chromium from tanning and retanning departments. Group 2 included 14 non-smoking male tannery workers with moderate chromium exposure from dying, drying and finishing departments. Group 3 included 11 healthy, non-smoking male subjects without direct chromium exposure. Higher serum chromium levels were observed in groups 1 and 2 with respect to group 3 (mean values respectively: 0.43; 0.25 and 0.13 microg x l(-1)). Urine chromium levels in group 1 were higher than those in controls (mean values: 1.78 and 1.35 microg x l(-1)). In group 1 an inverse association was found between serum chromium and urine iron (-0.524), urine chromium and hemoglobin (-0.594) and between the urine chromium to iron ratio and hemoglobin (-0.693, p<0.05). The results suggest a chromium adverse effect on iron metabolism, possibly associated with excessive body chromium accumulation. In conclusion, chromium urine test could be recommended for diagnosis of chromium adverse effect on iron metabolism. Further studies are needed to quantify the relationship between urine chromium and hemoglobin metabolism.

  2. Abrasive Performance of Chromium Carbide Reinforced Ni3Al Matrix Composite Cladding

    Institute of Scientific and Technical Information of China (English)

    LI Shang-ping; LUO He-li; FENG Di; CAO Xu; ZHANG Xi-e

    2009-01-01

    The Microstructure and room temperature abrasive wear resistance of chromium carbide reinforced NiM3Al matrix composite cladding at different depth on nickel base alloy were investigated. The results showed that there is a great difference in microstructure and wear resistance of the Ni3 Al matrix composite at different depth. Three kinds of tests, designed for different load and abrasive size, were used to understand the wear behaviour of this material. Under all three wear conditions, the abrasion resistance of the composite cladding at the depth of 6 mm, namely NC-M2, was much higher than that of the composite cladding at the depth of 2 mm, namely NC-M1. In addition, the wear-resistant advantage of NC-M2 was more obvious when the size of the abrasive was small. The relative wear resistance of NC-M2 increased from 1.63 times to 2.05 times when the size of the abrasive decreased from 180 μm to 50μm. The mierostructure of the composite cladding showed that the size of chromium carbide particles, which was mainly influenced by cooling rate of melting pool, was a function of distance from the interface between the coating and substrate varied gradually. The chromium carbide particles near the interface were finer than that far from inter-face, which was the main reason for the different wear resistance of the composite cladding at different depth.

  3. Comparison of chromium and nickel uptake of plants grown in different soils

    Energy Technology Data Exchange (ETDEWEB)

    Vago, I. [University of Agriculture, Faculty of Agronomy, H-4015 Debrecen, P.O. Box 36 (Hungary); Gyoeri, Z. [University of Agriculture, Faculty of Agronomy, H-4015 Debrecen, P.O. Box 36 (Hungary); Loch, J. [University of Agriculture, Faculty of Agronomy, H-4015 Debrecen, P.O. Box 36 (Hungary)

    1996-03-01

    The chromium and nickel uptake of ryegrass has been examined in pot experiments in extremely different soils, poor sandy and fertile black chernozem. The effect of calcium carbonate doses and nitrogen supply on heavy metal uptake of the plant has been studied for chromium and nickel loadings (0-100 mg/kg Cr{sup 3+} or Ni{sup 2+}) applied as inorganic salts. The ability to uptake Cr{sup 3+} and Ni{sup 2+} differs significantly and is highly affected by the characteristics of soils, and depends on the metal investigated. The heavy metal uptake of the plant differs significantly in acid, colloid deficient sandy soils; while artificial chromium contamination did not modify the dry-matter production in the pots in either soil, a large quantity of nickel reduced the yields significantly. Nitrogen application did not change significantly the uptake of heavy metals. Lime application reduced the Ni{sup 2+} uptake of plants considerably, especially in sandy soil. In case of a calcium carbonate addition the dry-matter production of the plant was not affected by nickel. In chernozem soil the effect of lime application - i.e., the reduction of nickel uptake - was of a lesser degree. The significantly lesser Cr{sup 3+} uptake was further limited by a calcium carbonate application for both soils studied. A graphic presentation of these effects is given. (orig.). With 3 figs., 3 tabs.

  4. The Incorporation of Chromium in Rice Straw Fermented with Ganoderma lucidum

    Directory of Open Access Journals (Sweden)

    F. Agustin

    2013-04-01

    Full Text Available The research was designed to evaluate chromium incorporation by Ganoderma lucidum in rice straw substrate supplemented with chromium chloride. Treatments were combination of Cr level (0, 500, 1000, 1500, 2000, 25000, and 3000 ppm and fermentation time (0, 2, 3, and 4 wk. The treatments were arranged in a factorial 7 x 4 and allocated in completely randomized design with three replications. G. lucidum was grown in potato dextrose agar (PDA medium for 10 days and was inoculated to the substrate which have been sterilized and mixed with CrCl3.6H2O. The moisture of substrate was maintained at 70%. Fiber and protein components of growth media of G. lucidum was determined and analyzed for their Cr content. The finding result showed that addition of Cr up to 3000 ppm into the substrate stimulated the G. lucidum growth. Chromium was incorporated into the fiber and protein components of the growth substrate of G. lucidum during fermentation. Incorporation of Cr into the protein of substrate containing 3000 ppm Cr was highest when fermented for 4 wk. Protein component of substrate contained 9.29% Cr while in NDF and ADF was 27.20% and 10.55% Cr, respectively. It is concluded that Cr was incorporated into the G. lucidum cells during fermentation.

  5. Additivity dominance

    Directory of Open Access Journals (Sweden)

    Paul Rozin

    2009-10-01

    Full Text Available Judgments of naturalness of foods tend to be more influenced by the process history of a food, rather than its actual constituents. Two types of processing of a ``natural'' food are to add something or to remove something. We report in this study, based on a large random sample of individuals from six countries (France, Germany, Italy, Switzerland, UK and USA that additives are considered defining features of what makes a food not natural, whereas ``subtractives'' are almost never mentioned. In support of this, skim milk (with major subtraction of fat is rated as more natural than whole milk with a small amount of natural vitamin D added. It is also noted that ``additives'' is a common word, with a synonym reported by a native speaker in 17 of 18 languages, whereas ``subtractive'' is lexicalized in only 1 of the 18 languages. We consider reasons for additivity dominance, relating it to omission bias, feature positive bias, and notions of purity.

  6. Potlining Additives

    Energy Technology Data Exchange (ETDEWEB)

    Rudolf Keller

    2004-08-10

    In this project, a concept to improve the performance of aluminum production cells by introducing potlining additives was examined and tested. Boron oxide was added to cathode blocks, and titanium was dissolved in the metal pool; this resulted in the formation of titanium diboride and caused the molten aluminum to wet the carbonaceous cathode surface. Such wetting reportedly leads to operational improvements and extended cell life. In addition, boron oxide suppresses cyanide formation. This final report presents and discusses the results of this project. Substantial economic benefits for the practical implementation of the technology are projected, especially for modern cells with graphitized blocks. For example, with an energy savings of about 5% and an increase in pot life from 1500 to 2500 days, a cost savings of $ 0.023 per pound of aluminum produced is projected for a 200 kA pot.

  7. Effects of chromium nanoparticle dosage on growth, body composition, serum hormones and tissue chromium in Sprague-Dawley rats

    Institute of Scientific and Technical Information of China (English)

    ZHA Long-ying; XU Zi-rong; WANG Min-qi; GU Liang-ying

    2007-01-01

    This 6-week study was conducted to evaluate the effects of seven different levels of dietary chromium (Cr) (0, 75, 150,300, 450, 600, and 1200 ppb Cr) in the form of Cr nanoparticle (CrNano) on growth, body composition, serum hormones and tissue Cr in Sprague-Dawley (SD) rats. Seventy male SD rats (average initial body weight of (83.2±4.4) g) were randomly assigned to seven dietary treatments (n=10). At the end of the trial, body composition was assessed via dual energy X-ray absorptiometry (DEXA). All rats were then sacrificed to collect samples of blood, organs and tissues for determination of serum hormones and tissue Cr contents. The results indicated that lean body mass was significantly increased (P<0.05) due to the addition of 300 and 450 ppb Cr from CrNano. Supplementation of 150, 300, 450, and 600 ppb Cr decreased (P<0.05) percent body fat significantly. Average daily gain was increased (P<0.05) by addition of 75, 150, and 300 ppb Cr and feed efficiency was increased (P<0.05) by supplementation of 75, 300, and 450 ppb Cr. Addition of 300 and 450 ppb Cr decreased (P<0.05) the insulin level in serum greatly. Cr contents in liver and kidney were greatly increased (P<0.05) by the addition of Cr as CrNano in the dosage of from 150 ppb to 1200 ppb. In addition, Supplementation of 300, 450, and 600 ppb Cr significantly increased (P<0.05) Cr content in the hind leg muscle. These results suggest that supplemental CrNano has beneficial effects on growth performance and body composition, and increases tissue Cr concentration in selected muscles.

  8. Additivity dominance

    OpenAIRE

    2009-01-01

    Judgments of naturalness of foods tend to be more influenced by the process history of a food, rather than its actual constituents. Two types of processing of a ``natural'' food are to add something or to remove something. We report in this study, based on a large random sample of individuals from six countries (France, Germany, Italy, Switzerland, UK and USA) that additives are considered defining features of what makes a food not natural, whereas ``subtractives'' are almost never mentioned....

  9. Thermodynamic Equilibrium Diagrams of Sulphur-Chromium System

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The chemical and electrochemical equilibria in the presence of gaseous phase were investigated. Many substances, which consisted of sulphur and chromium, were considered. Various thermodynamic equilibria were calculated in different pressures. Calculation results were shown as log p―1/T and E―T diagrams. These diagrams may be used to study the corrosion of chromium in sulphur-containing circumstances. The diagrams are also used to thermodynami-cally determine the existence area of various substances and so on.

  10. Stereology of carbide phase in modified hypereutectic chromium cast iron

    Directory of Open Access Journals (Sweden)

    J. Suchoń

    2010-04-01

    Full Text Available In paper are presented results of studies of carbide phase stereology modified hypereutectic wear resistance chromium cast iron which contains carbon about 3,5% and chromium about 25%. Three substances were applied to the modification: boron carbide (B4C, ferroniobium (FeNb and mixture of ferroniobium and rare-earth (RE. The measurements of geometrical features of carbides were conducted on microsection taken from castings wich were cooled with various velocities.

  11. SCIENCE AND TECHNOLOGY ACTIVITIES FOR CHROMIUM IN THE 100 AREAS

    Energy Technology Data Exchange (ETDEWEB)

    PETERSEN SW

    2009-07-02

    {sm_bullet} Primary Objective: Protect the Columbia River - Focus is control and treatment of contamination at or near the shoreline, which is influenced by bank storage {sm_bullet} Secondary Objective: Reduce hexavalent chromium to <48 parts per billion (ppb) in aquifer (drinking water standard) - Large plumes with isolated areas of high chromium concentrations (> 40,000 ppb), - Unknown source location(s); probably originating in reactor operation areas

  12. Chromium Ions Improve Moisure Resistance of Epoxy Resins

    Science.gov (United States)

    St. Clair, A. K.; St. Clair, T. L.; Stoakley, D. M.; Singh, J. J.; Sprinkle, D. R.

    1986-01-01

    Broad spectrum of thermosetting epoxy resins used on commercial and military aircraft, primarily as composite matrices and adhesives. In new technique, chromium-ion containing epoxy with improved resistance to moisture produced where chromium ions believed to prevent absorption of water molecules by coordinating themselves to hydroxyl groups on epoxy chain. Anticipated that improved epoxy formulation useful as composite matrix resin, adhesive, or casting resin for applications on commercial and advanced aircraft. Improvement made without sacrifice in mechanical properties of polymer.

  13. Performance of chromium nitride based coatings under plastic processing conditions

    OpenAIRE

    Cunha, l.; Andritschky, M.; Pischow, K.; Wang, Z.(Institute of High Energy Physics, Beijing, China); Zarychta, A.; Miranda, A. S.; A.M. Cunha

    2000-01-01

    Chromium nitride based coatings were produced in the form of monolithic and multilayer coatings, by DC and RF reactive magnetron sputtering. These coatings were deposited onto stainless steel and tool steel substrates. Chromium nitride coatings have;proved to be wear and corrosion resistant. The combination of these characteristics was necessary to protect surfaces during plastic processing. In order to select the best coatings, some mechanical and tribological tests were performed. Har...

  14. 40 CFR Appendix Xii to Part 266 - Nickel or Chromium-Bearing Materials that may be Processed in Exempt Nickel-Chromium Recovery...

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Nickel or Chromium-Bearing Materials that may be Processed in Exempt Nickel-Chromium Recovery Furnaces XII Appendix XII to Part 266... FACILITIES Pt. 266, App. XII Appendix XII to Part 266—Nickel or Chromium-Bearing Materials that may...

  15. Isolation and characterization of a chromium-resistant bacterium Serratia sp. Cr-10 from a chromate-contaminated site

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Kundi; Li, Fuli [Chinese Academy of Sciences, Qingdao (China). Qingdao Inst. of Bioenergy and Bioprocess Technology

    2011-05-15

    A novel bacterium, Cr-10, was isolated from a chromium-contaminated site and capable of removing toxic chromium species from solution by reducing hexavalent chromium to an insoluble precipitate. Sequence analysis of 16S rRNA gene of strain Cr-10 showed that it was most closely related to Serratia rubidaea JCM 1240{sup T} (97.68%). Physiological and chemotaxonomic data also supported that strain Cr-10 was identified as Serratia sp., a genus which was never specially reported chromate-resistant before. Serratia sp., Cr-10 was tolerant to a concentration of 1,500 mg Cr(VI) L{sup -1}, which was the highest level reported until now. The optimum pH and temperature for reduction of Cr(VI) by Serratia sp. Cr-10 were found to be 7.0 and 37 C, respectively. The Cr(VI) reduction was significantly influenced by additional carbon sources, and among them fructose and lactose offered maximum reduction, with a rate of 0.28 and 0.25 mg Cr(VI) L{sup -1} h{sup -1}, respectively. The cell-free extracts and filtrate of the culture were able to reduce Cr(VI) while concentration of total chromium remained stable in the process, indicating that the enzyme-catalyzed mechanism was applied in Cr(VI) reduction by the isolate. Additionally, it was found that there was hardly any chromium on the cell surface of the strain, further supporting that reduction, rather than bioadsorption, plays a major role in the Cr(VI) removal. (orig.)

  16. Lime enhanced chromium removal in advanced integrated wastewater pond system.

    Science.gov (United States)

    Tadesse, I; Isoaho, S A; Green, F B; Puhakka, J A

    2006-03-01

    The removal of trivalent chromium from a combined tannery effluent in horizontal settling tanks and subsequent Advanced Integrated Wastewater Pond System (AIWPS) reactors was investigated. The raw combined effluent from Modjo tannery had pH in the range of 11.2-12. At this pH, a trivalent chromium removal of 46-72% was obtained in the horizontal settling tanks after a one-day detention time. Trivalent chromium precipitated as chromium hydroxide, Cr(OH)3. 58-95% Cr(III) was removed in the advanced facultative pond (AFP) where the water column pH of 7.2-8.4 was close to pH 8, which is the optimum precipitation pH for trivalent chromium. Chromium removals in the secondary facultative pond (SFP) and maturation pond (MP) were 30-50% and 6-16%, respectively. With Cr(III) concentration of 0.2-0.8 mg/l in the final treated effluent, the AIWPS preceded by horizontal settling tanks produced effluent that could easily meet most of the current Cr(III) discharge limits to receive water bodies.

  17. Effect of Chromium on Microstructure and Mechanical Properties of Cold Rolled Hot-dip Galvanizing DP450 Steel

    Institute of Scientific and Technical Information of China (English)

    Yun HAN; Shuang KUANG; Hua-sai LIU; Ying-hua JIANG; Guang-hui LIU

    2015-01-01

    Two cold rolled hot-dip galvanizing dual phase (DP) 450 steels with different amounts of chromium were designed and the effects of the chromium concentration and galvanizing processes on the microstructure and mechanical properties were also investigated. The results show that the experimental steels exhibit typical dual phase microstructure character. However, the ferrite phase of steel with higher chromium is more regular and its boundaries are clearer. Meanwhile, martensite austenite (MA) island in steel No. 2 is diffused and no longer distributes along the grain boundary as net or chain shape. More MA islands enriched with Cr element can be found in the ferrite grains, and the increment of Cr element improves the stablity of the austenite so that the austenite has been reserved in MA islands. In addition, the experimental steel with higher chromium exhibits better elongation, lower yield ratio and better formability. The mean hole expanding ratio of steels No. 1 and No. 2 is 161.70% and 192.70%, respectively.

  18. Electrochemical removal of hexavalent chromium from wastewater using Platinum-Iron/Iron-carbon nanotubes and bipolar Electrodes

    Directory of Open Access Journals (Sweden)

    Hoshyar Hossini

    2015-01-01

    Full Text Available Background: In recent decades, electrocoagulation (EC has engrossed much attention as an environmental-friendly and effectiveness process. In addition, the EC process is a potential suitable way for treatment of wastewater with concern to costs and environment. The object of this study was electrochemical evaluation of chromium removal from industrial wastewater using Platinum and carbon nanotubes electrodes. Materials and Methods: The effect of key variables including pH (3–9, hexavalent chromium concentration (50–300 mg/l, supporting electrolyte (NaCl, KCl, Na2CO3 and KNO3 and its dosage, Oxidation-Reduction variations, sludge generation rate and current density (2–20 mA/cm2 was determined. Results: Based on experimental data, optimum conditions were determined in 20, 120 min, pH 3, NaCl 0.5% and 100 mg/L initial concentration of chromium. Conclusions: Removal of hexavalent chromium from the wastewater could be successfully performanced using Platinum-Iron/Iron-carbon nanotubes and bipolar Electrodes.

  19. Experimental skin deposition of chromium on the hands following handling of samples of leather and metal

    DEFF Research Database (Denmark)

    Bregnbak, David; Thyssen, Jacob P.; Jellesen, Morten Stendahl;

    2016-01-01

    Background: Chromium is an important skin sensitizer. Exposure to it has been regulated in cement, and recently in leather. Studies on the deposition of chromium ions on the skin as a result of handling different chromium-containing materials are sparse, but could improve the risk assessment...... of contact sensitization and allergic contact dermatitis caused by chromium. Objectives: To determine whether the handling of chromium-containing samples of leather and metal results in the deposition of chromium onto the skin. Methods: Five healthy volunteers participated. For 30 min, they handled samples...... of leather and metal known to contain and release chromium. Skin deposition of chromium was assessed with the acid wipe sampling technique. Results: Acid wipe sampling of the participants' fingers showed chromium deposition on the skin in all participants who had been exposed to leather (range 0.01–0.20 µg...

  20. [Chromium content in foods and dietary intake estimation in the Northwest of Mexico].

    Science.gov (United States)

    Grijalva Haro, M I; Ballesteros Vázquez, M N; Cabrera Pacheco, R M

    2001-03-01

    Chromium is an indispensable nutrient for the carbohydrates and lipids metabolism. In this study the chromium content in the twenty main foods of the diet from Northwestern Mexico was determined, as well as the daily mean intake which was estimated based on the food intake basket of this region. Chromium content was analyzed by atomic absorption spectrophotometry using the graphite furnace technique and previous digestion of foods in microwave oven. The chromium mean intake was estimated considering the chromium daily mean intake for person per day and the chromium content of the foods analyzed in this study. The range chromium content in the foods analyzed was between 0.0004 and 0.1641 microgram/g dry weight. White cheese showed the highest chromium content followed by pasta soup, wheat tortilla, bread and meat. The main foods chromium contributors in the diet were: wheat tortilla (20%), white cheese (11%), corn tortilla (11%), pasta soup (10%), milk (10%), meat (9%) and white bread (8%). The daily chromium intake was 30.43 +/- 1.6 micrograms/d. Chromium values obtained in the food analyzed are considered low. Moreover, chromium intake obtained from the diet is not enough to meet the safety and adequate daily chromium intake. Therefore, the population from the Northwestern Mexico has a suboptimal dietary chromium intake.

  1. Spectroscopic analysis of the interaction between chromium (III) and apoovotransferrin

    Energy Technology Data Exchange (ETDEWEB)

    Li Yingqi [Department of Chemistry, College of Chemistry and Chemical Engineering, Shanxi University, Taiyuan 030006 (China); Key Laboratory of Chemical Biology and Molecular Engineering of Ministry of Education, Institute of Molecular Science, Shanxi University, Taiyuan 030006 (China); Liu Bin [Key Laboratory of Chemical Biology and Molecular Engineering of Ministry of Education, Institute of Molecular Science, Shanxi University, Taiyuan 030006 (China); Yang Binsheng, E-mail: yangbs@sxu.edu.c [Key Laboratory of Chemical Biology and Molecular Engineering of Ministry of Education, Institute of Molecular Science, Shanxi University, Taiyuan 030006 (China)

    2010-12-15

    Ovotransferrin (OTf) is a main member of the transferrin family that functions both as an iron transporter and an antibacterial agent. In this study, the thermodynamic property of the interaction between chromium (III) and ovotransferrin was investigated. The conditional binding constants for Cr{sup 3+} binding to the protein were determined by difference UV spectroscopy and were found to be log K{sub C}=13.08{+-}0.24 and log K{sub N}=5.65{+-}0.12. It was found that Cr{sup 3+} preferentially binds to the C-terminal site over the N-terminal site under these experimental conditions. The conformational changes in apoovotransferrin (apoOTf) during Cr{sup 3+} binding were studied by fluorescence spectroscopy using 2-p-toluidinylnaphthalene-6-sulfonate (TNS) as the fluorescence probe and by circular dichroism (CD) spectroscopy. The results show that a large conformational change in apoOTf can be attributed to binding of Cr{sup 3+} to the N-terminal site, instead of the C-terminal site. In addition, the binding of Cr{sup 3+} to apoOTf stabilizes the structure of OTf as determined by guanidine hydrochloride denaturation studies. These findings help advance our understanding of the biological effects of Cr{sup 3+}.

  2. Solution growth of silicon carbide using unary chromium solvent

    Science.gov (United States)

    Miyasaka, Ryo; Kawanishi, Sakiko; Narumi, Taka; Sasaki, Hideaki; Yoshikawa, Takeshi; Maeda, Masafumi

    2017-02-01

    Solution growth of silicon carbide (SiC) using unary chromium (Cr) solvent was studied because the system enables a high solubility difference and a low degree of supersaturation, which would lead to rapid growth with a stabilized growth interface. The liquidus composition at SiC saturation in a quasi-binary Cr-SiC system was studied at 1823-2173 K. The measured carbon (C) contents are in good agreement with the thermodynamic evaluation using the sub-regular solution model. In addition, growth experiments using a unary Cr solvent were performed by the bottom-seeded travelling solvent method. The obtained growth rates at 1803-1923 K with a temperature difference of 15-70 K were proportional to the solubility difference between the seed and source temperatures, indicating that the growth was controlled by the mass transfer of C in the solution. The maximum growth rate of 720 μm/h at 1803 K was much higher than the growth rate by Si-rich solvents, suggesting that the Cr-rich solvent is suitable for the rapid growth at a low temperature.

  3. Kinetics of hexavalent chromium reduction by iron metal

    Institute of Scientific and Technical Information of China (English)

    Huijing QIAN; Yanjun WU; Yong LIU; Xinhua XU

    2008-01-01

    The kinetics of Cr(Ⅵ) reduction to Cr(Ⅲ) by metallic iron (Fe0) was studied in batch reactors for a range of reactant concentrations, pH and temperatures. Nearly 86.8% removal efficiency for Cr(Ⅵ) was achieved when Fe0 concentration was 6 g/L (using commercial iron powder (200 mesh) I n 120 min). The reduction ofhexavalent chro-mium took place on the surface of the iron particles following pseudo-first order kinetics. The rate of Cr(Ⅵ) reduction increased with increasing Fe0 addition and temperature but inversely with initial pH. The pseudo-first-order rate coeffi-cients (kobs) were determined as 0.0024, 0.010, 0.0268 and 0.062 8 min-1 when iron powder dosages were 2, 6, 10 and 14 g/L at 25℃ and pH 5.5, respectively. According to the Arrehenius equation, the apparent activation energy of 26.5 kJ/mol and pre-exponential factor of 3 330 min-1 were obtained at the temperature range of 288-308 K. Different Fe0 types were compared in this study. The reactivity was in the order starch-stabilized Fe0 nanoparticlesFe0 nano-particlesFe0 powderFe0 filings. Electrochemical analysis of the reaction process showed that Cr(Ⅲ) and Fe(Ⅲ) hydroxides should be the dominant final products.

  4. Alleviation of chromium toxicity by hydrogen sulfide in barley.

    Science.gov (United States)

    Ali, Shafaqat; Farooq, Muhammad Ahsan; Hussain, Sabir; Yasmeen, Tahira; Abbasi, G H; Zhang, Guoping

    2013-10-01

    A hydroponic experiment was carried out to examine the effect of hydrogen sulfide (H2 S) in alleviating chromium (Cr) stress in barley. A 2-factorial design with 6 replications was selected, including 3 levels of NaHS (0 μM, 100 μM, and 200 μM) and 2 levels of Cr (0 μM and 100 μM) as treatments. The results showed that NaHS addition enhances plant growth and photosynthesis slightly compared with the control. Moreover, NaHS alleviated the inhibition in plant growth and photosynthesis by Cr stress. Higher levels of NaHS exhibited more pronounced effects in reducing Cr concentrations in roots, shoots, and leaves. Ultrastructural examination of plant cells supported the facts by indication of visible alleviation of cell disorders in both root and leaf with exogenous application of NaHS. An increased number of plastoglobuli, disintegration, and disappearance of thylakoid membranes and starch granules were visualized inside the chloroplast of Cr-stressed plants. Starch accumulation in the chloroplasts was also noticed in the Cr-treated cells, with the effect being much less in Cr + NaHS-treated plants. Hence, it is concluded that H2 S produced from NaHS can improve plant tolerance under Cr stress.

  5. Chromium-chromium interaction in a binuclear mixed-valent Cr(I)-Cr(II) complex.

    Science.gov (United States)

    Alzamly, Ahmed; Gorelsky, Serge I; Gambarotta, Sandro; Korobkov, Ilia; Le Roy, Jennifer; Murugesu, Muralee

    2014-11-03

    A mixed-valent Cr(I)-Cr(II) binuclear complex, {κ(1),κ(2),κ(3)-N,P,P-cyclo[(Ph)PCH2N(CH2Ph)CH2]}2(CrCl2)[Cr(μ-Cl)(AlClMe2)]·4toluene (1), of a P2N2 cyclic ligand was obtained upon treatment of the chromium precursor with alkylaluminum. Complex 1 was accessible from either its trivalent or divalent precursors, and density functional theory calculations revealed the presence of only σ- and π-orbital interactions in the Cr-Cr bond.

  6. Environmental Factors Affecting Chromium-Manganese Oxidation-Reduction Reactions in Soil

    Institute of Scientific and Technical Information of China (English)

    D.O.P.TREBIEN; L.BORTOLON; M.J.TEDESCO; C.A.BISSANI; F.A.O.CAMARGO

    2011-01-01

    Disposal of chromium (Cr) hexavalent form, Cr(Ⅵ), in soils as additions in organic fertilizers, liming materials or plant nutrient sources can be dangerous since Cr(Ⅵ) can be highly toxic to plants, animals, and humans. In order to explore soil conditions that lead to Cr(Ⅵ) generation, this study were performed using a Paleudult (Dystic Nitosol) from a region that has a high concentration of tannery operations in the Rio Grande do Sul State, southern Brazil. Three laboratory incubation experiments were carried out to examine the influences of soil moisture content and concentration of cobalt and organic matter additions on soil Cr(Ⅵ) formation and release and manganese (Mn) oxide reduction with a salt of chromium chloride (CrCl3) and tannery sludge as inorganic and organic sources of Cr(Ⅲ), respectively. The amount of Cr(Ⅲ) oxidation depended on the concentration of easily reducible Mn oxides and the oxidation was more intense at the soil water contents in which Mn(Ⅲ/Ⅳ) oxides were more stable. Soluble organic compounds in soil decreased Cr(Ⅵ) formation due to Cr(Ⅲ) complexation. This mechanism also resulted in the decrease in the oxidation of Cr(Ⅲ) due to the tannery sludge additions. Chromium(Ⅲ) oxidation to Cr(Ⅵ) at the solid/solution interface involved the following mechanisms:the formation of a precursor complex on manganese (Mn) oxide surfaces, followed by electron transfer from Cr(Ⅲ) to Mn(Ⅲ or Ⅳ),the formation of a successor complex with Mn(Ⅱ) and Cr(Ⅵ), and the breakdown of the successor complex and release of Mn(Ⅱ) and Cr(Ⅵ) into the soil solution.

  7. CALVES GROWTH INFANT OF BREED NELLORE SUPPLEMENTED WITH CHROMIUM

    Directory of Open Access Journals (Sweden)

    C. C. Lima

    2016-11-01

    Full Text Available The present study evaluated the growth of nursling Nelore calves supplemented with chromium during creep feeding. The study was conducted using 131 Nelore calves with an average age of 60 days and average adjusted initial weight of 75 kg; considering that all calves were accompanied by their mothers. Therefore, the experimental groups were defined as T1: 35 males supplemented with chromium; T2: 34 males without chromium, T3: 30 females supplemented with chromium and T4: 32 females supplemented without chromium. The experimental period lasted from 60 days of age to 210 days (weaning, the animals were kept in two pickets of Panicum maximum cv. Mombasa provided with troughs for the creep feeding system, which permitted calves exclusive access to the concentrate formula based on 75% of TDN and 20% of crude protein, with 35% of soybean meal, 63% of corn and 2% of mineral nucleus containing 10 mg of chromium chelate for each kg of the product. The data were subjected to the analysis of variance, using the software R (R Development Core Team, 2013. In the evaluation of the live weight at 150 days of age, no significant difference was found in the use of chromium in males and females (regardless of sex. However, in the analysis between sexes, females’ live weights were lower than males’ live weight (p = 0.04, being 131.1 kg and 138.1 kg respectively. In the evaluation of live weight at 210 days there was no significant difference between males and females (p = 0.07, but there was a difference (p = 0.03 in the use of chrome in the evaluated treatments. So, it could be concluded that the creep feeding system with chrome chelate supplementation promoted an improvement in male and females calves’ growth for average daily weight gain and weaning weight, with a positive influence on the weight of cows.

  8. Nitridation of chromium powder in ammonia atmosphere

    Institute of Scientific and Technical Information of China (English)

    Ling Li; Qiang Zhen; Rong Li

    2015-01-01

    CrN powder was synthesized by nitriding Cr metal in ammonia gas flow, and its chemical reaction mechanism and nitridation process were studied. Through thermodynamic calculations, the Cr−N−O predominance diagrams were constructed for different tempera-tures. Chromium nitride formed at 700−1200°C under relatively higher nitrogen and lower oxygen partial pressures. Phases in the products were then investigated using X-ray diffraction (XRD), and the Cr2N content varied with reaction temperature and holding time. The results indicate that the Cr metal powder nitridation process can be explained by a diffusion model. Further, Cr2N formed as an intermediate product because of an incomplete reaction, which was observed by high-resolution transmission electron microscopy (HRTEM). After nitriding at 1000°C for 20 h, CrN powder with an average grain size of 63 nm was obtained, and the obtained sample was analyzed by using a scanning electron microscope (SEM).

  9. Chromium increases pancreatic metallothionein in the rat.

    Science.gov (United States)

    Solis-Heredia, M J; Quintanilla-Vega, B; Sierra-Santoyo, A; Hernández, J M; Brambila, E; Cebrián, M E; Albores, A

    2000-01-03

    The ability of chromium (Cr) salts to increase metallothionein (MT) levels in rat liver, kidney and pancreas, and its relationship with the presence of toxic effects are reported here. Rats were injected subcutaneously with 0, 10, 20, 30, 40, or 50 mg K2Cr2O7/kg and sacrificed 24 h later. Total Cr accumulation followed a dose-dependent pattern, levels in kidney being higher than those in liver or pancreas, suggesting different tissue bioavailabilities and accumulation patterns. Cr(IV) administration resulted in a tissue-specific MT induction: pancreas and liver showed five- and 3.5-fold MT increases, respectively; no increase was observed in the kidney. A positive correlation was observed between zinc and MT concentrations in liver, and between total Cr and MT concentrations in pancreas. Serum alpha-amylase activity showed a dose-dependent increase starting from 20 mg/kg, whereas serum glucose levels increased at doses higher than 30 mg/kg. Serum aspartate aminotransferase and alanine aminotransferase activities were increased in a dose-dependent manner, from 20 and 30 mg/kg, respectively. Our results showed that treatment with Cr(VI) can induce MT synthesis in pancreas and suggests a subsequent binding of Cr to MT. Also, pancreas is a target organ for Cr toxicity, and the usefulness of alpha-amylase activity as a sensitive biomarker of Cr toxicity in human exposed populations merits further study.

  10. Can elevated chromium induce somatopsychic responses?

    Science.gov (United States)

    Lovrincevic, I; Leung, F Y; Alfieri, M A; Grace, D M

    1996-01-01

    The possible somatopsychological effects of chromium (Cr) was investigated in a population of patients, from a surgical ward of our hospital, who required total parenteral nutrition (TPN) solutions, and who became exposed to various amounts of this metal from this treatment. The study involved a questionnaire as well as biochemical tests which included serum Cr and other selected trace metals. The renal status for all eligible patients was within normal parameters. The patient population varied in age, pathology, surgical treatment, and duration on TPN. The results showed that every patient who received TPN had an increased serum Cr level; some increases were up to 50-fold above the normal reference level for serum Cr. Although statistical analysis failed to show any significant statistical relationship between an increased serum Cr and the investigated somatopsychological disturbances, this effect cannot be ruled out since one case did show all the dream disturbances. Considering these cases, the action of sedative medications that may suppress the effects of Cr, cannot be ruled out. As Cr(III) may be potentially genotoxic at high concentrations, infusion of this metal over long time periods should be avoided. Supplementation of Cr in TPN solutions appears to be unnecessary for short-term TPN because this metal is a known contaminant of these solutions. Efforts are required to find TPN nutrients with low or no Cr contamination.

  11. 污染场地六价铬的还原和微生物稳定化研究%Bioremediation of Chromium (Ⅵ(Contaminated Site by Reduction and Microbial Stabilization of Chromium

    Institute of Scientific and Technical Information of China (English)

    郑家传; 张建荣; 刘希雯; 许倩; 施维林

    2014-01-01

    Chromium(Ⅵ) contaminated soil samples were collected from a chemical plant in Suzhou. Firstly, the reduced soil was prepared by adding reagent (Stone-sulfure reagent) into polluted soil to transfer most chromium(Ⅵ) into chromium(Ⅲ), then a nutrient solution was introduced into the reduced soil, and the stabilized soil was obtained after 60 days culturing. The chromium(Ⅵ) content of the three kinds of soil was analyzed. The results showed that the chromium(Ⅵ) content in toxicity characteristic leaching liquid ( TCLL) dropped by 96. 8% ( from 8. 26 mg·L-1 to 0. 26 mg·L-1 ) , and the total chromium content dropped by 95. 7% ( from 14. 66 mg·L-1 to 0. 63 mg·L-1 ) after bioremediation in 5% nutrient solution. Additionally, the durability of chromium stabilization was tested by potassium permanganate oxidation and sterilization of microbe-treated soil. After oxidation, the chromium(Ⅵ) content in TCLL of the reduced soil was increased from 8. 26 mg·L-1 to 14. 68 mg·L-1 . However, the content after bioremediation was decreased to 2. 68 mg·L-1 . The results of sterilization demonstrated that the death of microbe had no significant effect on the stabilization of chromium. Consequently, the research in this paper demonstrated the feasibility of bioremediation of chromium (Ⅵ) polluted soil through reduction followed by stabilization/soilidification, and provided a technique with low cost but high efficiency.%通过采集苏州某化工原址场地铬污染土壤,首先加入石硫合剂使大部分六价铬[ Cr(Ⅵ)]还原,再加入营养液促进土著微生物大量生长,利用微生物还原稳定化土壤中的铬.培养60 d后,通过毒性浸出、土壤中剩余Cr(Ⅵ)测定等实验确定稳定化效果,结果表明,加入5%营养液培养后,土壤毒性浸出液中Cr(Ⅵ)浓度由原来的8.26 mg·L-1降低到0.26 mg·L-1,降低了96.8%,总铬浓度由原来14.66 mg·L-1降低到0.63 mg·L-1,降低了95.7%.另外,通过高锰酸钾氧化

  12. Hexavalent Chromium Reduction and Its Distribution in the Cell and Medium by Chromium Resistant Fusarium solani

    Directory of Open Access Journals (Sweden)

    Mousumi Sen

    2013-01-01

    Full Text Available In the present work, batch biosorption of Cr(VI was studied using the fungal strain isolated from soil. The fungal strain was characterized as Fusarium solani. The total Cr distribution in the biomass (fungus and in the media obtained from the experiment conducted at 500 mg l -1 initial Cr(VI concentration and pH 5.0. The results indicated both intracellular and extracellular accumulation and enzymatic reduction of Cr(VI and this was supported by the Transmission Electron Microscopic (TEM observation at the same Cr(VI concentration and pH value. Chromium elution from Fusarium solani containing Cr was then tried out using a number of chromium eluting reagents and a maximum Cr could be eluted using 0.5N sodium hydroxide solution without destructing the biomass structure. The total Cr was recovered by pH adjustment from both biomass and media was found to be 44% of the initial Cr(VI concentration (500 mg l-1.

  13. Effects of RE, V, Ti and B composite modification on the microstructure and properties of high chromium cast iron containing 3 % molybdenum

    Institute of Scientific and Technical Information of China (English)

    GUO Erjun; WANG Lihua; WANG Liping; HUANG Yongchang

    2009-01-01

    The effects of RE, V, Ti and B on the microstructure and properties of high chromium cast iron containing 3% molybdenum under as-cast and heat treatment conditions were investigated with the method of comparing experiments. The results show that with the increase of RE content, the primary austenite of high chromium east iron is obviously refined. The morphology of carbide is changed from netlike and lath to small multiangular isolated blocks or massive blocks, the isolated degree of carbide is improved obviously, and the size is significantly re-fined. The addition of V and B into high chromium cast iron can refine the microstructure, reduce coarse columnar crystals and make the carbide smaller and uniform. Through composite modification with RE, V, Ti and B, the hardness, wear resistance and impact toughness of high chromium cast iron are increased conspicuously. After heat treatment, the hardness of high chromium iron is increased significantly, but the toughness and wear resistance do not show great improvement.

  14. Performance Study of Chromium (VI Removal in Presence of Phenol in a Continuous Packed Bed Reactor by Escherichia coli Isolated from East Calcutta Wetlands

    Directory of Open Access Journals (Sweden)

    Bhaswati Chakraborty

    2013-01-01

    Full Text Available Organic pollutants, like phenol, along with heavy metals, like chromium, are present in various industrial effluents that pose serious health hazard to humans. The present study looked at removal of chromium (VI in presence of phenol in a counter-current continuous packed bed reactor packed with E. coli cells immobilized on clay chips. The cells removed 85% of 500 mg/L of chromium (VI from MS media containing glucose. Glucose was then replaced by 500 mg/L phenol. Temperature and pH of the MS media prior to addition of phenol were 30°C and 7, respectively. Hydraulic retention times of phenol- and chromium (VI-containing synthetic media and air flow rates were varied to study the removal efficiency of the reactor system. Then temperature conditions of the reactor system were varied from 10°C to 50°C, the optimum being 30°C. The pH of the media was varied from pH 1 to pH 12, and the optimum pH was found to be 7. The maximum removal efficiency of 77.7% was achieved for synthetic media containing phenol and chromium (VI in the continuous reactor system at optimized conditions, namely, hydraulic retention time at 4.44 hr, air flow rate at 2.5 lpm, temperature at 30°C, and pH at 7.

  15. Microbial reduction of hexavalent chromium under vadose zone conditions.

    Science.gov (United States)

    Oliver, Douglas S; Brockman, Fred J; Bowman, Robert S; Kieft, Thomas L

    2003-01-01

    Hexavalent chromium [Cr(VI)] is a common contaminant associated with nuclear reactors and fuel processing. Improper disposal at facilities in and and semiarid regions has contaminated underlying vadose zones and aquifers. The objectives of this study were to assess the potential for immobilizing Cr(VI) using a native microbial community to reduce soluble Cr(VI) to insoluble Cr(III) under conditions similar to those in the vadose zone, and to evaluate the potential for enhancing biological Cr(VI) reduction through nutrient addition. Batch microcosm and unsaturated flow column experiments were performed. Native microbial communities in subsurface sediments with no prior Cr(VI) exposure were shown to be capable of Cr(VI) reduction. In both the batch and column experiments, Cr(VI) reduction and loss from the aqueous phase were enhanced by adding high levels of both nitrate (NO3-) and organic C (molasses). Nutrient amendments resulted in up to 87% reduction of the initial 67 mg L(-1) Cr(VI) in an unsaturated batch experiment. Molasses and nitrate additions to 15 cm long unsaturated flow columns receiving 65 mg L(-1) Cr(VI) resulted in microbially mediated reduction and immobilization of 10% of the Cr during a 45-d experiment. All of the immobilized Cr was in the form of Cr(III), as shown by XANES analysis. This suggests that biostimulation of microbial Cr(VI) reduction in vadose zones by nutrient amendment is a promising strategy, and that immobilization of close to 100% of Cr contamination could be achieved in a thick vadose zone with longer flow paths and longer contact times than in this experiment.

  16. Microbial reduction of hexavalent Chromium under vadose zone conditions

    Energy Technology Data Exchange (ETDEWEB)

    Oliver, D S.(unknown); Brockman, Fred J.(BATTELLE (PACIFIC NW LAB)); Bowman, Robert (VISITORS); Kieft, Thomas L.(BATTELLE (PACIFIC NW LAB))

    2003-01-01

    Hexavalent chromium[Cr(VI)] is a common constituent of wastes associated with nuclear reactor operation and fuel processing. Improper disposal at facilities in arid and semi-arid regions has led to contamination of underlying vadose zones and aquifers. The objectives of this study were to assess the potential for immobilizing Cr(VI) contamination using a native microbial community to reduce soluble Cr(VI) to insoluble Cr(III) under conditions similar to those found in the vadose zone, and to evaluate the potential for enhancing biological reduction of Cr(VI) through the addition of nutrients. Batch microcosm and unsaturated flow column experiments were performed. Native microbial communities in subsurface sediments with no prior Cr(VI) exposure were shown to be capable of Cr(VI) reduction. In both the batch and column experiments, Cr(VI) reduction and loss from the aqueous phase were enhanced by adding high levels of both nitrate (NO3-) and organic carbon (molasses). Nutrient amendments resulted in up to 87% Cr(VI) reduction in unsaturated batch experiments. Molasses and nitrate additions to 15-cm length unsaturated flow columns receiving 65 mg L-1 Cr(VI) resulted in microbially mediated reduction and immobilization of 10% of the Cr during a 45-day experiment. All of the immobilized Cr was in the form of Cr (III), as shown by XANES analysis. This suggests that biostimulation of microbial Cr(VI) reduction in vadose zones by nutrient amendment is a promising strategy; and that immobilization of close to 100% of Cr contamination could be achieved in a thick vadose zone with longer flow paths and longer contact times than in this experiment.

  17. Spectroscopic study for a chromium-adsorbed montmorillonite

    Science.gov (United States)

    Nurtay, Maidina ·; Tuersun, Maierdan ·; Cai, Yuanfeng; Açıkgöz, Muhammed; Wang, Hongtao; Pan, Yuguan; Zhang, Xiaoke; Ma, Xiaomei

    2017-02-01

    Samples of purified montmorillonite with trace amounts of quartz were subjected to different concentrations of chromium sulphate solutions for one week to allow cation exchange. The chromium-bearing montmorillonites were verified and tested using powder X-ray diffractometry (XRD), X-ray fluorescence spectrometry, electron spin resonance (ESR) spectrometry and Fourier transformation infrared (FTIR) spectroscopy to explore the occupation sites of the chromium. The ESR spectra recorded before and after the chromium exchange show clear differences: a strong and broad resonance with two shoulders at the lower magnetic field side was present to start, and its intensity as well as that of the ferric iron resonance, increased with the concentration of added chromium. The signals introduced by the chromium, for example at g = 1.975 and 2.510 etc., suggested that the chromium had several occupational sites. The ESR peak with g = 2.510 in the second derivative spectrum suggested that Cr3+ was weakly bounded to TOT with the form of [Cr(H2O)3]3+ in hexagonal cavities. This was verified by comparing the FTIR spectra of the pure and modified montmorillonite. The main resonance centred at g = 1.975 indicated that the majority of Cr3+ occupied the interlayer region as [Cr(H2O)6]3+. The substitution of Ca2 + by Cr3+ also greatly affected the vibration of the hydrogens associate to water, ranged from 3500 to 2600 cm-1 in FTIR. Furthermore, the presence of two diffraction lines in the XRD results (specifically those with d-values of 1.5171 and 1.2673 nm) and the calculations of the size of the interlayer space suggested the presence of two types of montmorillonite with different hydration cations in the sample exposed to 0.2 M chromium sulphate. The two diffraction lines were assigned to [Cr(H2O)6]3+ and [Cr(H2O)3O3]3+, respectively. This also suggested that the species of hydration cation was constrained by the concentration of the chromium solution.

  18. Effects of chromium(III and VI) on spring barley and maize biomass yield and content of nitrogenous compounds.

    Science.gov (United States)

    Wyszkowski, Mirosław; Radziemska, Maja

    2010-01-01

    The aim of this study was to (1) determine the effects of trivalent Cr(III) or hexavalent chromium Cr(VI) soil contamination on biomass yield and nitrogenous compound content of spring barley (Hordeum vulgare L.) as the main crop and subsequently maize (Zea mays L.) grown successively, and (2) examine whether the neutralizing additives applied (compost, zeolite, and calcium oxide) may be effective in reducing adverse impact of chromium (Cr) on crops. Spring barley yield was markedly decreased by Cr compounds, particularly Cr(VI). In contrast, maize yield was significantly increased by Cr(VI). Hexavalent Cr exerted a greater effect than the Cr(III) form on nitrogen levels in spring barley. Chromium significantly increased ammonia nitrogen content in maize. The accumulation of NO(3)(-)-N in plants treated with Cr(VI) was lower than in controls. The application of compost, zeolite, and calcium oxide onto the soil increased yield of maize only in pots containing Cr(III). Neutralizing additives exerted a positive, increased effect on the N-total content of maize but not spring barley, which was apparent with calcium oxide. Accumulation of NH(4)(+)-N in maize in pots with Cr(VI) was increased by all additives applied. The content of nitrate nitrogen in spring barley was predominantly affected by addition of compost and calcium oxide into the soil, producing a significant rise in NO(3)(-)-N content. Chromium, especially Cr(VI), used at doses of 100 and 150 mg/kg soil exerted adverse effects in treated plants, particularly spring barley.

  19. A possible role for chromium(III) in genotoxicity

    Energy Technology Data Exchange (ETDEWEB)

    Snow, E.T. (New York Univ. Medical Center, Tuxedo (United States))

    1991-05-01

    Chromium is found in the environment in two major forms: reduced Cr{sup III} and Cr{sup VI}, or chromate. Chromate, the most biologically active species, is readily taken up by living cells and reduced intracellularly, via reactive intermediates, to stable Cr{sup III} species. Cr{sup III}, the most abundant form of chromium in the environment, does not readily cross cell membranes and is relatively inactive in vivo. However, intracellular Cr{sup III} can react slowly with both nucleic acids and proteins and can be genotoxic. The authors have investigated the genotoxicity of Cr{sup III} in vitro using a DNA replication assay and in vivo by CaCl{sub 2}-mediated transfection of chromium-treated DNA into Escherichia coli. These results suggest that Cr{sup III} alters the interaction between the DNA template and the polymerase such that the binding strength of the DNA polymerase is increased and the fidelity of DNA replication is decreased. These interactions may contribute to the mutagenicity of chromium ions in vivo and suggest that Cr{sup III} can contribute to chromium-mediated carcinogenesis.

  20. Low-chromium reduced-activation ferritic steels for fusion

    Energy Technology Data Exchange (ETDEWEB)

    Klueh, R.L.; Alexander, D.J.; Kenik, E.A. [Oak Ridge National Laboratory, TN (United States)

    1996-04-01

    Development of reduced-activation ferritic steels has concentrated on high-chromium (8-10 wt% Cr) steels. However, there are advantages for a low-chromium steel, and initial ORNL studies on reduced-activation steels were on compositions with 2.25 to 12% Cr. Those studies showed an Fe-2.25Cr-2W-0.25V-0.1C (2 1/4Cr-2WV) steel to have the highest strenglth of the steels studied. Although this steel had the best strength, Charpy impact properties were inferior to those of an Fe-9Cr-2W-0.25V-0.07Ta-0.1C (9Cr-2WVTa) and an Fe-2.25Cr-2W-0.1C (2 1/4Cr-2W) steel. Therefore, further development of the low-chromium Cr-W steels was required. These results indicate that it is possible to develop low-chromium reduced-activation ferritic steels that have tensile and impact properties as good or better than those of high-chromium (7-9% Cr) steels. Further improvement of properties should be possible by optimizing the composition.

  1. Enhancement of chromium uptake in tanning using oxazolidine.

    Science.gov (United States)

    Sundarapandiyan, S; Brutto, Patrick E; Siddhartha, G; Ramesh, R; Ramanaiah, B; Saravanan, P; Mandal, A B

    2011-06-15

    Monocyclic and bicyclic oxazolidines were offered at three different junctures of chrome tanning process viz. prior to BCS offer, along with BCS and after basification. It was found that oxazolidine when offered after basification brought about better chromium uptake and reduction of chromium load in the wastewater. Offer of oxazolidine was also varied. Increase in offer of oxazolidine from 0.25% to 1% was found to enhance the chromium uptake and decrease the chromium load in wastewater. But the increase in uptake was not proportionate to the increase in oxazolidine offer more than 0.75%. Offer of 1% Zoldine ZA 78 (monocyclic oxazolidine) and Zoldine ZE (bicyclic oxazolidine) after basification brought about 63.4% and 73.1% enhancement in chrome content in leather compared to control where oxazolidine was not offered. The tone of the wetblue was found to be altered moderately. However this did not call for any process adjustments in wet-finishing. The oxazolidine treated leathers were found to be immensely fuller and tighter. It was found experimentally that offer of 1% of oxazolidine facilitated reduction in the offer of syntans administered for filling and grain tightening by around 46%. Oxazolidine could bring about significant reduction in cost of chemicals apart from resulting environmental benefits due to enhancement of chromium uptake during tanning.

  2. Bioaccumulation and biosorption of chromium by Aspergillus niger MTCC 2594.

    Science.gov (United States)

    Sandana Mala, John Geraldine; Unni Nair, Balachandran; Puvanakrishnan, Rengarajulu

    2006-06-01

    Chromium toxicity is of prime concern due to chrome tanning processes in the leather sector. Chrome tanning results in the discharge of toxic levels of chromium causing pollution hazards. Chromium levels of Cr(III) and Cr(VI) were high above permissible limits in chrome samples after chrome tanning. The potential of Aspergillus niger MTCC 2594 to accumulate chromium as well as its biosorption capacity is investigated in this study. Bioaccumulation of Cr(III) and Cr(VI) in the spent chrome liquor has resulted in a 75-78% reduction of the initial Cr content in 24-36 h. A. niger biomass is found to be very effective in the biosorption of Cr(III) and Cr(VI) in spent chrome liquor. Maximum adsorption of 83% for biosorption of Cr(III) at 48 h and 79% of Cr(VI) at 36 h in spent chrome liquor is observed. The biosorption characteristics fit well with Langmuir and Freundlich isotherms and the adsorption parameters are evaluated. The biosorption of Cr also follows Lagergren kinetics. A. niger biomass is effectively used for the biosorption of chromium with 79-83% Cr removal in 36-48 h.

  3. Microbial exudate promoted dissolution and transformation of chromium containing minerals

    Science.gov (United States)

    Saad, E. M.; Sun, J.; Tang, Y.

    2015-12-01

    Because of its utility in many industrial processes, chromium has become the second most common metal contaminant in the United States. The two most common oxidation states of chromium in nature are Cr(III), which is highly immobile, and Cr(VI), which is highly mobile and toxic. In both natural and engineered environments, the most common remediation of Cr(VI) is through reduction, which results in chromium sequestration in the low solubility mixed Cr(III)-Fe(III) (oxy)hydroxide phases. Consequently, the stability of these minerals must be examined to assess the fate of chromium in the subsurface. We examined the dissolution of mixed Cr(III)-Fe(III) (oxy)hydroxides in the presence of common microbial exudates, including the siderophore desferrioxamine B (DFOB; a common organic ligand secreted by most microbes with high affinity for ferric iron and other trivalent metal ions) and oxalate (a common organic acid produced by microbes). The solids exhibited incongruent dissolution with preferential leaching of Fe from the solid phase. Over time, this leads to a more Cr rich mineral, which is known to be more soluble than the corresponding mixed mineral phase. We are currently investigating the structure of the reacted mineral phases and soluble Cr(III) species, as well as the potential oxidation and remobilization of the soluble Cr species. Results from this study will provide insights regarding the long term transport and fate of chromium in the natural environment in the presence of microbial activities.

  4. Effective bioleaching of chromium in tannery sludge with an enriched sulfur-oxidizing bacterial community.

    Science.gov (United States)

    Zeng, Jing; Gou, Min; Tang, Yue-Qin; Li, Guo-Ying; Sun, Zhao-Yong; Kida, Kenji

    2016-10-01

    In this study, a sulfur-oxidizing community was enriched from activated sludge generated in tannery wastewater treatment plants. Bioleaching of tannery sludge containing 0.9-1.2% chromium was investigated to evaluate the effectiveness of the enriched community, the effect of chromium binding forms on bioleaching efficiency, and the dominant microbes contributing to chromium bioleaching. Sludge samples inoculated with the enriched community presented 79.9-96.8% of chromium leaching efficiencies, much higher than those without the enriched community. High bioleaching efficiencies of over 95% were achieved for chromium in reducible fraction, while 60.9-97.9% were observed for chromium in oxidizable and residual fractions. Acidithiobacillus thiooxidans, the predominant bacteria in the enriched community, played an important role in bioleaching, whereas some indigenous heterotrophic species in sludge might have had a supporting role. The results indicated that A. thiooxidans-dominant enriched microbial community had high chromium bioleaching efficiency, and chromium binding forms affected the bioleaching performance.

  5. Development of a coprecipitation system for the speciation/preconcentration of chromium in tap waters

    Energy Technology Data Exchange (ETDEWEB)

    Karatepe, Aslihan, E-mail: karatepea@gmail.com [Nevsehir University, Faculty of Science and Arts, Department of Chemistry, 50000 Nevsehir (Turkey); Korkmaz, Esra [Bozok University, Faculty of Science and Arts, Department of Chemistry, Yozgat (Turkey); Soylak, Mustafa [Erciyes University, Faculty of Science and Arts, Chemistry Department, 38039 Kayseri (Turkey); Elci, Latif [Pamukkale University, Faculty of Science and Arts, Department of Chemistry, 20020 Denizli (Turkey)

    2010-01-15

    A method for the speciation of chromium(III), chromium(VI) and determination of total chromium based on coprecipitation of chromium(III) with dysprosium hydroxide has been investigated and applied to tap water samples. Chromium(III) was quantitatively recovered by the presented method, while the recovery values for chromium(VI) was below 10%. The influences of analytical parameters including amount of dysprosium(III), pH, centrifugation speed and sample volume for the quantitative precipitation were examined. No interferic effects were observed from alkali, earth alkali and some transition metals for the analyte ions. The detection limits (k = 3, N = 15) were 0.65 {mu}g/L for chromium(III) and 0.78 {mu}g/L for chromium(VI). The validation of the presented method was checked by the analysis of certified reference materials.

  6. CHROMIUM ELECTROANALYSIS AT SCREEN PRINTED ELECTRODE MODIFIED BY THIN FILMS OF NICKEL

    Science.gov (United States)

    A rapid and potentially cost-effective electrochemical method is reported for analysis of chromium (VI) and Chromium(III) using a nickel modified screen printed carbon ink electrode. Electrochemical characteristics of nickel modified electrode as well voltammetric behavior f...

  7. Magnetite nanoparticle (NP) uptake by wheat plants and its effect on cadmium and chromium toxicological behavior

    Energy Technology Data Exchange (ETDEWEB)

    López-Luna, J., E-mail: jlol_24@hotmail.com [Instituto de Estudios Ambientales, Universidad de la Sierra Juárez, Ixtlán de Juárez 68725, Oaxaca (Mexico); Silva-Silva, M.J. [Instituto de Estudios Ambientales, Universidad de la Sierra Juárez, Ixtlán de Juárez 68725, Oaxaca (Mexico); Martinez-Vargas, S. [Facultad de Ingeniería, Universidad Autónoma del Carmen, Ciudad del Carmen 24115, Campeche (Mexico); Mijangos-Ricardez, O.F. [Instituto de Estudios Ambientales, Universidad de la Sierra Juárez, Ixtlán de Juárez 68725, Oaxaca (Mexico); González-Chávez, M.C. [Colegio de Postgraduados en Ciencias Agrícolas, Carr. México–Texcoco km 36.5, Montecillo 56230, Estado de México (Mexico); Solís-Domínguez, F.A. [Facultad de Ingeniería, Universidad Autónoma de Baja California, Mexicali 21280, Baja California Norte (Mexico); Cuevas-Díaz, M.C. [Facultad de Ciencias Químicas, Universidad Veracruzana, Coatzacoalcos 96535, Veracruz (Mexico)

    2016-09-15

    The aim of this work was to assess the uptake of citrate-coated magnetite nanoparticles (NPs) by wheat plants and its effect on the bioaccumulation and toxicity of individual and joint Cd{sup 2+} and Cr{sup 6+} levels. Seven-day assays were conducted using quartz sand as the plant growth substrate. The endpoints measured were seed germination, root and shoot lengths, and heavy metal accumulation. Magnetite exhibited very low toxicity, regardless of the wheat seedling NP uptake and distribution into roots and shoots. The seed germination and shoot length were not sensitive enough, while the root length was a more sensitive toxicity endpoint. The root length of wheat seedlings exposed to individual metals decreased by 50% at 2.67 mg Cd{sup 2+} kg{sup −1} and 5.53 mg Cr{sup 6+} kg{sup −1}. However, when magnetite NPs (1000 mg kg{sup −1}) were added, the root length of the plants increased by 25 and 50%. Cd{sup 2+} and Cr{sup 6+} showed similar and noninteractive joint action, but strongly impaired the wheat seedlings. In contrast, an interactive infra-additive or antagonistic effect was observed upon adding magnetite NPs. Thus, cadmium and chromium accumulation in vegetable tissues was considerately diminished and the toxicity alleviated. - Highlights: • We assessed the effect of nanomagnetite on heavy metal toxicity in wheat plants. • Citrate-coated magnetite nanoparticles (NPs) exerted very low toxicity to plants. • Cadmium was more toxic than chromium and toxicity was mitigated by magnetite NPs. • Cadmium and chromium had a similar and noninteractive joint action on plants. • Metals showed an interactive infra-additive joint effect by adding magnetite NPs.

  8. Evaluation of effect of recasting of nickel-chromium alloy on its castability using different investment materials: An in vitro study

    Directory of Open Access Journals (Sweden)

    Abhinav Sharma

    2016-01-01

    Conclusions: Within the limitations of the study, it was concluded that there was no significant difference found in castability of different percentage combinations of new and once casted alloy using two investment materials. The addition of new alloy during recasting to maintain the castability of nickel-chromium alloy may therefore not be required.

  9. Effect Of Oxidation On Chromium Leaching And Redox Capacity Of Slag-Containing Waste Forms

    Energy Technology Data Exchange (ETDEWEB)

    Almond, P. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Stefanko, D. B. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Langton, C. A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2013-03-01

    The rate of oxidation is important to the long-term performance of reducing salt waste forms because the solubility of some contaminants, e.g., technetium, is a function of oxidation state. TcO4- in the salt solution is reduced to Tc(IV) and has been shown to react with ingredients in the waste form to precipitate low solubility sulfide and/or oxide phases [Shuh, et al., 1994, Shuh, et al., 2000, Shuh, et al., 2003]. Upon exposure to oxygen, the compounds containing Tc(IV) oxidize to the pertechnetate ion, Tc(VII)O4-, which is very soluble. Consequently the rate of technetium oxidation front advancement into a monolith and the technetium leaching profile as a function of depth from an exposed surface are important to waste form performance and ground water concentration predictions. An approach for measuring contaminant oxidation rate (effective contaminant specific oxidation rate) based on leaching of select contaminants of concern is described in this report. In addition, the relationship between reduction capacity and contaminant oxidation is addressed. Chromate was used as a non-radioactive surrogate for pertechnetate in simulated waste form samples. Depth discrete subsamples were cut from material exposed to Savannah River Site (SRS) field cured conditions. The subsamples were prepared and analyzed for both reduction capacity and chromium leachability. Results from field-cured samples indicate that the depth at which leachable chromium was detected advanced further into the sample exposed for 302 days compared to the sample exposed to air for 118 days (at least 50 mm compared to at least 20 mm). Data for only two exposure time intervals is currently available. Data for additional exposure times are required to develop an equation for the oxidation front progression. Reduction capacity measurements (per the Angus-Glasser method, which is a measurement of the ability of a material to chemically reduce Ce(IV) to Ce

  10. Reduction of chromium oxide from slags

    Directory of Open Access Journals (Sweden)

    Gutiérrez-Paredes, J.

    2005-12-01

    Full Text Available Experimental and theoretical work were performed to estimate the effect of slag basicity and amount of reducing agents on the reduction of chromium oxide from the slag which interacted with molten steel at 1,600 °C. The slag system contained CaO, MgO, SiO2, CaF2 and Cr2O3 together with Fe-alloys (Fe-Si and Fe-Si-Mg. The CaF2 and MgO contents in the slags were 10 mass % each; Cr2O3 was 25%. The amount of the ferroalloys ranged from 12.5 to 50 g per 100 g of slag. The (CaO+MgO/SiO2 ratio was held at 1 and 2. The Cr yield was determined using both Fe-alloys as reducing agents. Some estimations were made to determine the theoretical effect of temperature, slag basicity, (CaO+MgO/SiO2, and amount of reducing agents in the slag on the chromium recovery. The FACT (Facility for the Analysis of Chemical Thermodynamics computational package is used to determine the equilibrium between the slag and molten steel.

    En el presente trabajo se realiza un estudio teórico y experimental para determinar el efecto de la basicidad de la escoria y la cantidad de agentes reductores sobre la reducción de óxidos de cromo contenidos en la escoria, la cual está en contacto con acero líquido a 1.600 °C. La escoria se prepara con los reactivos CaO, MgO, SiO2, CaF2 y ferroaleaciones (Fe-Si y Fe-Si-Mg. Los contenidos de CaF2 y MgO en la escoria son de 10 %, cada uno, y el de Cr2O3 es 25 %. La cantidad de la ferroaleación varía de 12,5 a 50 g por cada 100 g de escoria. La relación (CaO+MgO/SiO2 tiene los valores de 1 y 2. Se determina la eficiencia de recuperación de cromo empleando los dos tipos de ferroaleaciones. Se realizaron cálculos para determinar el efecto teórico de la temperatura, la basicidad de la escoria, (CaO+MgO/SiO2, y la cantidad de agentes reductores sobre la reducci

  11. Effects of irradiation on chromium's behavior in ferritic/martensitic FeCr alloy

    Institute of Scientific and Technical Information of China (English)

    Xinfu HE; Wen YANG; Zhehao QU; Sheng FAN

    2009-01-01

    The effects of irradiation on chromium performance under different temperatures in Fe-20at%Cr were modeled by modified Marlowe code. Chromium precipitation was observed in FeCr alloy after irradiation; interstitial Chromium atoms are the preferred formation of mixed FeCr dumbbells in the direction ofand; interstitial chromium atoms congregated on {111} and {110} plane. The results are compared with experiment observations and are useful to understanding the irradiation performances of FeCr alloy.

  12. A study of the process of desorption of hexavalent chromium

    Directory of Open Access Journals (Sweden)

    W.B. Amorim

    2003-09-01

    Full Text Available In this work the process of desorption of hexavalent chromium, a toxic metal ion, from the marine algae Sargassum sp, following biosorption experiments 2³ factorial design was studied. A technique was applied to three eluents: HCl, H2SO4 and EDTA. Three factors of importance were evaluated: concentration of eluent, the ratio between mass of biosorbent and volume of eluent (S/L and process time. A statistical analysis of the experimental results showed that the three variables evaluated are significant for all three eluents. The models for chromium desorption were validated, as the results agreed well with the observed values. Through use of the response surface methodology, a factorial design based optimization technique; it was possible to identify the most suitable eluent and the interval of values for the process variables that resulted in the most significant desorption of chromium, which is relevant information for work aiming at process optimization.

  13. Bioabsorption of chromium from retan chrome liquor by cyanobacteria.

    Science.gov (United States)

    Pandi, M; Shashirekha, V; Swamy, Mahadeswara

    2009-01-01

    The bioaccumulation of chromium from retan chrome liquor by Spirulina fusiformis was investigated under laboratory as well as field conditions. At the optimal conditions, metal ion uptake increased with initial metal ion concentration up to 300mg/l. The effect on various physico-chemical parameters like total solids (TS), total dissolved solids (TDS), total suspended solids (TSS), chlorides, sulphates, phenols, biochemical oxygen demand (BOD) and chemical oxygen demand (COD) and biochemical studies related to biomass, chlorophyll-a and protein were also carried out. The present study indicates that S. fusiformis is very effective in removal of chromium (93-99%) besides removing other toxicants from retan chrome liquor. The sodium dodecyl sulphate-polyacrylamide gel electrophoresis (SDS-PAGE) and FTIR studies indicate the interaction/complexation between Cr and alga. The mechanism involved in bioaccumulation of chromium is also discussed. The process when upgraded can be applied for detoxification of tannery effluents.

  14. Extraction of Chromium from Carbon Ferrochromium Residual Wastes

    Science.gov (United States)

    Lazarevskiy, P. P.; Gizatulin, R. A.; Romanenko, Yu E.; Valuev, D. V.; Valueva, A. V.; Serikbol, A.

    2015-09-01

    This work reports the problem of processing residual wastes after producing carbon ferrochrome by recycling dust using a hydrometallurgical method with the purpose of extracting the basic component - chromium, The X-ray diffraction analysis results, chemical and granulometric compositions of dust from the carbon ferrochrome production are given, The method for the production of chemical-enrichment concentrate (CEC) by processing ferrous dust is described, with obtaining a middling product - sodium mono-chromate with its further reduction to chromium hydroxide, followed by autoclave leaching, and resulting in the production of chemically enriched chrome concentrate, The plant used for autoclave leaching and filtering is schematically depicted, The smelting process of metallic chromium using the ladle aluminothermic method is described,

  15. Studies of removal of chromium by model constructed wetland

    Directory of Open Access Journals (Sweden)

    C. Mant

    2005-09-01

    Full Text Available Chromium is a pollutant present in tannery wastewater, its removal is necessary for protection of the environment. Penisetum purpureum, Brancharia decumbens and Phragmites australis were grown hydroponically in experimental gravel beds to determine their potential for the phytoremediation of solutions containing 10 and 20 mg Cr dm-3. These concentrations, similar to tannery wastewater after initial physico-chemical treatment were used with the aim of developing an economic secondary treatment to protect the environment. All the systems achieved removal efficiencies of 97 - 99.6% within 24 hours. P. purpureum and B. decumbens removed 78.1% and 68.5% respectively within the first hour. Both P. purpureum and B. decumbens were tolerant of the concentrations of chromium applied, but P. purpureum showed the greatest potential because its faster growth and larger biomass achieved a much greater chromium removal over the whole length of time of the experiment.

  16. Electron magnetic resonance investigation of chromium diffusion in yttria powders

    Energy Technology Data Exchange (ETDEWEB)

    Biasi, R.S. de, E-mail: rsbiasi@ime.eb.b [Secao de Engenharia Mecanica e de Materiais, Instituto Militar de Engenharia, Pr. General Tiburcio, 80, 22290-270 Rio de Janeiro, RJ (Brazil); Grillo, M.L.N., E-mail: mluciag@uerj.b [Instituto de Fisica, Universidade do Estado do Rio de Janeiro, 20550-013 Rio de Janeiro, RJ (Brazil)

    2010-03-01

    The electron magnetic resonance (EMR) technique was used to investigate the diffusion of chromium in yttria (Y{sub 2}O{sub 3}) powders. The EMR absorption intensity was measured for several annealing times and three different temperatures of isothermal annealing: 1273, 1323 and 1373 K. The activation temperature for diffusion, calculated from the experimental data using a theoretical model based on the Fick equation, was found to be E{sub A}=342+-5 kJ mol{sup -1}. This value is larger than the activation energy for the diffusion of chromium in rutile (TiO{sub 2}), periclase (MgO) and cobalt monoxide (CoO) and smaller than the activation energy for the diffusion of chromium in chrysoberyl (BeAl{sub 2}O{sub 4}).

  17. Chromium Resistant Bacteria: Impact on Plant Growth in Soil Microcosm

    Directory of Open Access Journals (Sweden)

    Sayel Hanane

    2014-07-01

    Full Text Available Three chromium resistant bacterial strains, Pseudomonas fluorescens PF28, Enterobacter amnigenus EA31 and Enterococcus gallinarum S34 isolated from tannery waste contaminated soil were used in this study. All strains could resist a high concentration of K2Cr2O7 that is up to 300 mg/L. The effect of these strains on clover plants (Trifolium campestre in the presence of two chromium salts CrCl3 and K2Cr2O7 was studied in soil microcosm. Application of chromium salts adversely affected seed germination, root and shoot length. Bacterial inoculation improved the growth parameters under chromate stress when compared with non inoculated respective controls. There was observed more than 50% reduction of Cr(VI in inoculated soil microcosms, as compared to the uninoculated soil under the same conditions. The results obtained in this study are significant for the bioremediation of chromate pollution.

  18. Improvement on simultaneous determination of chromium species in aqueous solution by ion chromatography and chemiluminescence detection

    DEFF Research Database (Denmark)

    Gammelgaard, Bente; Liao, Y.P.; Jons, O.

    1997-01-01

    A sensitive method for the simultaneous determination of chromium(III) and chromium(VI) was chromatography and chemiluminescence detection. Two Dionex ion-exchange guard columns in series, CG5 and AG7, were used to separate chromium(III) from chromium(VI). Chromium(VI) was reduced by potassium......, the stabilities of reductant and luminol solutions were studied. The linear range of the calibration curve for chromium(III) and chromium(VI) was 1-400 mu g l(-1). The detection limit was 0.12 mu g l(-1) for chromium(III) and 0.09 mu g l(-1) for chromium(VI), respectively. The precision at the 20 mu g l(-1) level...... was 1.4% for chromium(III) and 2.5% for chromium(VI), respectively. The accuracy of the chromium(III) determination was determined by analysis of the NIST standard reference material 1643c, Trace elements in water with the result 19.1 +/- 1.0 mu g Cr(III) l(-1) (certified value 19.0 +/- 0.6 mu g Cr...

  19. Experimental study on 830 MPa grade pipeline steel containing chromium

    Institute of Scientific and Technical Information of China (English)

    Yi Ren; Shuai Zhang; Shuang Wang; Wen-yue Liu

    2009-01-01

    The diversity of microstructure and properties of 830 Mpa grade pipeline steel containing chromium was investigated by optical microscope and transmission electron microscopy. The main microstructures were multiple configurations, containing lath bainite and granule bainite. Mechanical properties test results showed that the yield strength and tensile strength improved with in-creasing chromium content. The toughness and elongation decreased at the same time, so temper process was introduced. Appling proper temper parameters, the values of toughness and elongation were improved dramatically, and the strength decreased slightly.

  20. Fractionation behavior of chromium isotopes during coprecipitation with calcium carbonate

    DEFF Research Database (Denmark)

    Rodler, Alexandra; Sánchez-Pastor, Nuria; Fernández-Díaz, Lurdes;

    2015-01-01

    Interest in chromium (Cr) isotope incorporation into carbonates arises from the observation that Cr isotopic composition of carbonates could be used as a paleoclimate proxy to elucidate past fluctuations of oxygen contents in atmosphere and hydrosphere. The use of Cr isotopes to track paleoenviro......Interest in chromium (Cr) isotope incorporation into carbonates arises from the observation that Cr isotopic composition of carbonates could be used as a paleoclimate proxy to elucidate past fluctuations of oxygen contents in atmosphere and hydrosphere. The use of Cr isotopes to track...

  1. Use of chitosan for chromium removal from exhausted tanning baths.

    Science.gov (United States)

    Cesaro, Raffaele; Fabbricino, Massimiliano; Lanzetta, Rosa; Mancino, Anna; Naviglio, Biagio; Parrilli, Michelangelo; Sartorio, Roberto; Tomaselli, Michele; Tortora, Gelsomina

    2008-01-01

    A novel approach, based on chitosan heavy-metal sequestrating ability, is proposed for chromium(III) removal from spent tanning liquor. Experimental results, obtained at lab-scale using real wastewater, are presented and discussed. Resulting efficiencies are extremely high, and strongly dependent on chitosan dose and pH value. Comparative analyses with other polysaccharides is also carried out showing that amine groups are more efficient than carboxyl and sulphate ones. Chromium recovery from sorption complexes and chitosan regeneration is finally proposed to optimize the whole process.

  2. Primary and secondary crystallization of modified hypoeutectic chromium cast iron

    Directory of Open Access Journals (Sweden)

    A. Studnicki

    2010-04-01

    Full Text Available The paper presents investigations of crystallization of modified hypoeutectic wear resistant chromium cast iron which contains carbon about 2% and chromium on three levels (12%, 18% and 25%. Three substances were applied to the modification ( boron carbide (B4C, ferroniobium (FeNb and mixture of ferroniobium and mischmetal (RE. The investigations of crystallization were conducted the DTA method in DTA-C and DTA-Is testers. The influence on the course of the process of primary and secondary crystallization was observed.

  3. Urinary levels of nickel and chromium associated with dental restoration by nickel-chromium based alloys.

    Science.gov (United States)

    Chen, Bo; Xia, Gang; Cao, Xin-Ming; Wang, Jue; Xu, Bi-Yao; Huang, Pu; Chen, Yue; Jiang, Qing-Wu

    2013-03-01

    This paper aims to investigate if the dental restoration of nickel-chromium based alloy (Ni-Cr) leads to the enhanced excretions of Ni and Cr in urine. Seven hundred and ninety-five patients in a dental hospital had single or multiple Ni-Cr alloy restoration recently and 198 controls were recruited to collect information on dental restoration by questionnaire and clinical examination. Urinary concentrations of Ni and Cr from each subject were measure by graphite furnace atomic absorption spectrometry. Compared to the control group, the urinary level of Ni was significantly higher in the patient group of dental restoration. Potential short- and long-term effects of Ni-Cr alloy restoration need to be investigated.

  4. Fertilizers and Mixed Crop Cultivation of Chromium Tolerant and Sensitive Plants under Chromium Toxicity

    Directory of Open Access Journals (Sweden)

    B. Dheeba

    2015-01-01

    Full Text Available Zea mays (maize and Vigna radiata (green gram are found to be the chromium (Cr tolerant and sensitive plants, respectively. In the present paper, we investigate the reduction of the toxicity of Cr in the sensitive plants by the mixed crop cultivation in the field using various amendments. Further, the potassium dichromate was used as the source of hexavalent Cr. The results indicated that Cr adversely affects both the growth and yield of plants. The soil properties vary with Cr and different fertilizer amendments and the yield of both plants were affected by Cr. We conclude that metal accumulation of seeds of green gram was higher than corn and the application of single fertilizer either farm yard manure (FYM or nitrogen, phosphorous, and potassium (NPK enhances the growth and yield of both the tolerant and sensitive plants in the mixed crop cultivations.

  5. Spatial distribution of chromium in soils contaminated by chromium-containing slag

    Institute of Scientific and Technical Information of China (English)

    HUANG Shun-hong; PENG Bing; YANG Zhi-hui; CHAI Li-yuan; XU You-ze; SU Chang-qing

    2009-01-01

    To evaluate the metal chromium (Cr) contamination of soil at a chromium-containing slag site by ferrochromium production, the contaminated sites, under slag heap, in the vicinity of slag heap and arable soils near the outlet of sewer channel, and unpolluted site 5 km away from one ferroalloy plant in Hunan Province, China, were selected. The concentrations of total Cr and water soluble Cr in bulk soil samples and profile depth samples were determined. The results show that the soils in the vicinity of slag heap have the highest total Cr content followed by the soils under the slag heap and near the outlet of sewer channel of the factory. The mean concentrations of total Cr in the top soils at above three contaminated locations exceed the critical level of Secondary Environmental Quality Standard for Soil in China by 3.5, 5.4 and 1.8 times. In most Cr polluted soils, total Cr has a relative accumulation in soil depth of 40-60 cm, but this trend is not found in unpolluted soils. The average concentrations of water soluble Cr (Ⅵ) in top soils under slag heap and in the vicinity of slag heap are 176.9 times and 52.7 times higher than that in the uncontaminated soils, respectively. However, water soluble Cr (Ⅵ) contents in soils near sewer channel are all low and the values are close to that in the uncontaminated soils. Although water soluble Cr (Ⅵ) content in soil profiles decreases with soil depths, it in soils under slag heap maintains a high level even at a depth of 100-150 cm. The results imply that the transportation of Cr (Ⅵ) can result in a potential risk of groundwater system in this area.

  6. Lysozyme adsorption on the colloidal chromium(III) oxide surface: Its impact on the system stability

    Energy Technology Data Exchange (ETDEWEB)

    Szewczuk-Karpisz, Katarzyna, E-mail: k.szewczuk-karpisz@wp.pl; Wiśniewska, Małgorzata; Myśliwiec, Dawid

    2015-08-30

    Highlights: • Lysozyme adsorption mechanism on the chromium(III) oxide surface was determined. • Surface charge density as well as zeta potential of Cr{sub 2}O{sub 3} particles were measured. • Turbidimetric method was used to estimate the suspension stability. • Depending on the pH value, lysozyme increases or decreases the system stability. - Abstract: This paper describes the lysozyme (LSZ) presence effect on the chromium(III) oxide (Cr{sub 2}O{sub 3}) suspension stability. First, the electrokinetic properties of the examined system, i.e. surface charge density and zeta potential of solid particles in the absence and presence of LSZ, were determined. The lysozyme addition reduces the metal oxide surface charge, which may be related to the interaction of the LSZ protonated amino groups with the adsorbent surface moieties. The LSZ macromolecules undergo adsorption on the Cr{sub 2}O{sub 3} surface only under electrostatic attraction. At the LSZ concentrations above 50 ppm the macromolecules cover completely the particle surface, which is evidenced by the observed zeta potential values. The LSZ influence on the Cr{sub 2}O{sub 3} suspension stability depends on the solution pH value. At pH 3, 4.6 and 7.6, the LSZ addition improves the system stability. In turn, at pH 9 it is associated with the slight suspension destabilization.

  7. Inhibition of nitrate reduction by chromium (VI) in anaerobic soil microcosms

    Energy Technology Data Exchange (ETDEWEB)

    Kourtev, P. S.; Nakatsu, C. H.; Konopka, Allan

    2009-10-01

    Chromium (VI) is often found as a co-contaminant at sites polluted with organic compounds. We used microcosms amended with glucose or protein, nitrate and increasing concentrations of chromium to study nitrate reduction in Cr(VI) polluted soils. Organic carbon stimulated bacterial activity, but the addition of Cr(VI) caused a lag and then slower rates 5 of CO2 accumulation. Nitrate reduction only occurred after Cr(VI) had been reduced. Bacterial activity was again inhibited when Cr(VI) was added a second time; thus not all Cr-sensitive bacteria were removed in the first phase. Glucose and protein selected for relatively similar bacterial communities, as assayed by PCR-DGGE of the 16S rRNA gene; this selection was modified by the addition of 10 Cr(VI). Cr-resistant bacteria isolated from microcosms were closely related to members of Bacillus, Enterococcus and Propionibacterium sp. Our results indicate that carbon utilization and nitrate reduction in these soils in the presence of Cr(VI) are contingent upon the reduction of the added heavy metal by a limited subset of the bacterial community. The amount of Cr(VI) required to inhibit nitrate reduction was 10-fold less than for aerobic catabolism of the same 15 substrate. We hypothesize that the resistance level of a microbial process is directly related to the diversity of microbes capable of conducting it.

  8. Effect of chromium on the corrosion behaviour of powder-processed Fe–0·45 wt% P alloys

    Indian Academy of Sciences (India)

    Yashwant Mehta; Shefali Trivedi; K Chandra; P S Mishra

    2010-08-01

    The corrosion behaviour of Fe–0·45P with/without addition of chromium, prepared by powder forging route was studied in different environments. The corrosion studies in acidic (0·25 M H2SO4 solution of pH 0·6) and neutral/marine (3·5% NaCl solution of pH 6·8) solutions were conducted using Tafel Extrapolation method. The rate of corrosion in alkaline medium (0·5 M Na2CO3 + 1·0 M NaHCO3 solution of pH 9·4) was measured using linear polarization technique. The studies compare electrolytic Armco iron with Fe–P alloys. It was observed that, chromium improved the resistance to corrosion in acidic and marine environments. The corrosion rates were minimal in alkaline medium and low in neutral solution.

  9. Remanent life assessment of creep resistant modified 12% chromium steels: microstructural analysis and microstructural development models

    Energy Technology Data Exchange (ETDEWEB)

    Lundin, L.; Andren, H.O. [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Physics; Norell, M.; Nyborg, L. [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Engineering Metals

    1996-09-01

    In this report, an overview of the current status of the development work, physical metallurgy and creep properties of 9-12% chromium steels is given. These steels find their application mainly in the power generating industry, at high temperatures. In Sweden, a co-operation between research groups specialized at microanalysis and modelling of 9-12% chromium steels has been initiated. This co-operation is outlined in this report, as well as the most important results achieved so far. The microstructure of four different alloys have been studied in detail with different analytical methods including atom-probe field-ion microscopy, electron microscopy and Auger electron spectroscopy. The role of different elements on precipitation processes and the composition of all relevant phases have been studied. Furthermore, segregation of impurity elements to creep cavities and creep fracture surfaces have been studied for two of the alloys. Models for the microstructural development of 9-12% chromium steels during heat treatment and creep testing are currently being produced. The work has been focused on modelling the nucleation and growth of MN and M{sub 23}C{sub 6} precipitates during tempering, and the first results from these studies are currently being compared to microscopy observation. In addition, equilibrium phase calculations have been made and been found to predict existing phases to a high degree. A complete description of the creep properties of these steels must also include a model of the relationship between microstructure and creep behaviour. However, the microstructural development models will form an important basis for complete models of this kind. 57 refs

  10. Hemocompatibility Improvement of Chromium-Bearing Bare-Metal Stent Platform After Magnetoelectropolishing

    Science.gov (United States)

    Rokicki, Ryszard; Haider, Waseem; Maffi, Shivani Kaushal

    2015-01-01

    Research was undertaken to determine the influence of the increased content of chromium in the outermost passive layer of magneto-electrochemically refined Co-Cr alloy L-605 surface on its hemocompatibility. The chemistry, roughness, surface energy, and wettability of conventionally electropolished (EP) and magnetoelectropolished (MEP) samples were studied with x-ray photoelectron spectroscopy (XPS), open circuit potential, atomic force microscopy, and contact angle meter. In vitro hemocompatibility of tested material surfaces was assessed using two important indicators of vascular responses to biomaterial, namely endothelialization and platelets adhesion. The endothelialization was assessed by seeding and incubating samples with human umbilical vein endothelial cells (HUVEC) for 3 days before counting and observing them under a fluorescent microscope. The platelet (rich plasma blood) adhesion and activation test on EP and MEP L-605 alloy surfaces was assessed using a laser scanning confocal microscope. The XPS analysis of MEP samples showed significant enrichment of the passive layer with Cr and O when compared with the EP one. The amount of other elements in the passive layer did not show a significant difference between EP and MEP treatments. The adhesion of HUVEC cells shows remarkable affinity to surfaces enriched in Cr (MEP) with almost 100% confluency. In addition, the number of platelets that adhered to standard EP surfaces was higher compared to the MEP surface. The present study shows that the chromium-enriched surface of cobalt-chromium alloy L-605 by the magnetoelectropolishing process tremendously improves surface hemocompatibility with regard to stent functionality by enhanced endothelialization and lower platelet adhesion and should be taken under consideration as an alternative surface of biodegradable polymer drug-eluting stents, polymer-free drug-eluting stents as well as bare-metal stents.

  11. Techniques for Achieving Zero Stress in Thin Films of Iridium, Chromium, and Nickel

    Science.gov (United States)

    Broadway, David M.; O'Dell, Stephen L.; Ramsey, Brian D.; Weimer, Jeffrey

    2015-01-01

    We examine techniques for achieving zero intrinsic stress in thin films of iridium, chromium, and nickel deposited by magnetron sputter deposition. The intrinsic stress is further correlated to the microstructural features and physical properties such as surface roughness and optical density at a scale appropriate to soft X-ray wavelengths. The examination of the stress in these materials is motivated by efforts to advance the optical performance of light-weight X-ray space telescopes into the regime of sub-arcsecond resolution through various deposition techniques that rely on control of the film stress to values within 10-100 MPa. A characteristic feature of the intrinsic stress behavior in chromium and nickel is their sensitivity to the magnitude and sign of the intrinsic stress with argon gas pressure and deposition rate, including the existence of a critical argon process pressure that results in zero film stress which scales linearly with the atomic mass of the sputtered species. While the effect of stress reversal with argon pressure has been previously reported by Hoffman and others for nickel and chromium, we report this effect for iridium. In addition to stress reversal, we identify zero stress in the optical functioning iridium layer shortly after island coalescence for low process pressures at a film thickness of approximately 35nm. The measurement of the low values of stress during deposition was achieved with the aid of a sensitive in-situ instrument capable of a minimum detectable level of stress, assuming a 35nm thick film, in the range of 0.40-6.0 MPa for oriented crystalline silicon substrate thicknesses of 70-280 microns, respectively.

  12. Survey of Nano filtration Performance for Hexavalent Chromium Removal fromWater Containing Sulfate

    Directory of Open Access Journals (Sweden)

    Gh.R Moussavi

    2010-10-01

    Full Text Available "n "n "nBackgrounds and Objectives: Geological situation and/or anthropogenic contamination contain an increased concentration of ions such as hexavalent chromium as well as some other dissolved components such as sulfate in the upper of the establishedMCLs (50µg/L. In this paper, simultaneous removal of Cr (VI and sulfate from water was investigated using nanofiltration as a promising method for reaching drinking water standards."nMaterials and Methods: For varying pressure, pH , anion and cation solution effect, Sulfate and Cr (VI concentration which have chosen were levels found in drinking water sources (Cr=0.1- 0.5mg/L and (SO4-2= 100-800mg/L.Experiments were performed using NaCl, Na2SO4,K2 Cr2O7and anhydrous CrCl3. 6H2O which prepared with de mineralized water on procedure detailed in standard methods. All salts were purchased from Merck Corporation with purity over 99'."nResults: The results for hexavalent chromium experiments showed that when the concentration decreases, the chromate anions were given a better retention to 4 bars (96'. But when the concentration increases, concentration polarization led to increased removal of Cr (VI (98'. For Cr (III the influences of the ionic strength as well as the concentrations were strongly dependant on rejection but operating pressure were found weak. In addition, with increasing total dissolved solids, perfect rejection of chromium was seen. The effect of pH showed that better retention was obtained at natural and basic pH."nConclusion: This study indicates that the nature of anions and cations, driven pressure and pH have significant effect on nano filtration operation. Research findings show that it seems nano filtration is a very good promising method of simultaneous removal of Cr (VI and sulfate from water.

  13. Effect of molybdenum, vanadium, boron on mechanical properties of high chromium white cast iron in as-cast condition

    Science.gov (United States)

    Nurjaman, F.; Sumardi, S.; Shofi, A.; Aryati, M.; Suharno, B.

    2016-02-01

    In this experiment, the effect of the addition carbide forming elements on high chromium white cast iron, such as molybdenum, vanadium and boron on its mechanical properties and microstructure was investigated. The high chromium white cast iron was produced by casting process and formed in 50 mm size of grinding balls with several compositions. Characterization of these grinding balls was conducted by using some testing methods, such as: chemical and microstructure analysis, hardness, and impact test. From the results, the addition of molybdenum, vanadium, and boron on high chromium white cast iron provided a significant improvement on its hardness, but reduced its toughness. Molybdenum induced fully austenitic matrix and Mo2C formation among eutectic M7C3 carbide. Vanadium was dissolved in the matrix and carbide. While boron was played a role to form fine eutectic carbide. Grinding balls with 1.89 C-13.1 Cr-1.32 Mo-1.36 V-0.00051 B in as-cast condition had the highest hardness, which was caused by finer structure of eutectic carbide, needle like structure (upper bainite) matrix, and martensite on its carbide boundary.

  14. Physiological, biochemical and histometric responses of Nile tilapia (Oreochromis niloticus L.) by dietary organic chromium (chromium picolinate) supplementation

    OpenAIRE

    2014-01-01

    Chromium has been recognized as a new and important micro-nutrient, essential for both human and animal nutrition. This study was conducted to evaluate the appropriateness and/or the use of safety level of dietary chromium picolinate (Cr-Pic), and its effects on the physiological responses, the histometric characteristics, and the chemical analysis of dorsal muscles of mono-sex Nile tilapia, Oreochromis niloticus. A total of 420 fingerlings (28.00 ± 0.96 g) were randomly distributed into 21 f...

  15. Chromium(VI) release from leather and metals can be detected with a diphenylcarbazide spot test

    DEFF Research Database (Denmark)

    Bregnbak, David; Johansen, Jeanne D.; Jellesen, Morten Stendahl

    2015-01-01

    Along with chromium, nickel and cobalt are the clinically most important metal allergens. However, unlike for nickel and cobalt, there is no validated colorimetric spot test that detects chromium. Such a test could help both clinicians and their patients with chromium dermatitis to identify culprit...... at 0.5 ppm without interference from other pure metals, alloys, or leather. A market survey using the test showed no chromium(VI) release from work tools (0/100). However, chromium(VI) release from metal screws (7/60), one earring (1/50), leather shoes (4/100) and leather gloves (6/11) was observed. We...

  16. Reactor target from metal chromium for "pure" high-intensive artificial neutrino source

    Science.gov (United States)

    Gavrin, V. N.; Kozlova, Yu. P.; Veretenkin, E. P.; Logachev, A. V.; Logacheva, A. I.; Lednev, I. S.; Okunkova, A. A.

    2017-01-01

    The paper presents the first results of development of manufacturing technology of metallic chromium targets from highly enriched isotope 50Cr for irradiation in a high flux nuclear reactor to obtain a compact high intensity neutrino source with low content of radionuclide impurities and minimum losses of enriched isotope. The main technological stages are the hydrolysis of chromyl fluoride, the electrochemical reduction of metallic chromium, the hot isostatic pressing of chromium powder and the electrical discharge machining of chromium bars. The technological stages of hot isostatic pressing of chromium powder and of electrical discharge machining of Cr rods have been tested.

  17. The oxidation and reduction of chromium of stainless steels in an eletric arc furnace

    Directory of Open Access Journals (Sweden)

    B. Arh

    2011-07-01

    Full Text Available The oxidation of chromium during the elaboration of stainless steels occurs with oxygen in solution blown inthe melt and with oxides in the slag. A higher content of silicon in the furnace charge decreases the extent of oxidation of chromium, however, the efficient reduction of chromium from the slag is of essential importance for a minimal loss of chromium. In this survey, the theory of the oxidation of chromium, its reduction from the slag and the conditions for the formation of foaming slag are discussed.

  18. The chromium isotope composition of reducing and oxic marine sediments

    Science.gov (United States)

    Gueguen, Bleuenn; Reinhard, Christopher T.; Algeo, Thomas J.; Peterson, Larry C.; Nielsen, Sune G.; Wang, Xiangli; Rowe, Harry; Planavsky, Noah J.

    2016-07-01

    The chromium (Cr) isotope composition of marine sediments has the potential to provide new insights into the evolution of Earth-surface redox conditions. There are significant but poorly constrained isotope fractionations associated with oxidative subaerial weathering and riverine transport, the major source of seawater Cr, and with partial Cr reduction during burial in marine sediments, the major sink for seawater Cr. A more comprehensive understanding of these processes is needed to establish global Cr isotope mass balance and to gauge the utility of Cr isotopes as a paleoredox proxy. For these purposes, we investigated the Cr isotope composition of reducing sediments from the upwelling zone of the Peru Margin and the deep Cariaco Basin. Chromium is present in marine sediments in both detrital and authigenic phases, and to estimate the isotopic composition of the authigenic fraction, we measured δ53Cr on a weakly acid-leached fraction in addition to the bulk sediment. In an effort to examine potential variability in the Cr isotope composition of the detrital fraction, we also measured δ53Cr on a variety of oxic marine sediments that contain minimal authigenic Cr. The average δ53Cr value of the oxic sediments examined here is -0.05 ± 0.10‰ (2σ, n = 25), which is within the range of δ53Cr values characteristic of the bulk silicate Earth. This implies that uncertainty in estimates of authigenic δ53Cr values based on bulk sediment analyses is mainly linked to estimation of the ratio of Cr in detrital versus authigenic phases, rather than to the Cr-isotopic composition of the detrital pool. Leaches of Cariaco Basin sediments have an average δ53Cr value of +0.38 ± 0.10‰ (2σ, n = 7), which shows no dependency on sample location within the basin and is close to that of Atlantic deepwater Cr (∼+0.5‰). This suggests that authigenic Cr in anoxic sediments may reliably reflect the first-order Cr isotope composition of deepwaters. For Peru Margin samples

  19. Chromium(VI) transport and fate in unsaturated zone and aquifer: 3D Sandbox results.

    Science.gov (United States)

    Zhao, Xingmin; Sobecky, Patricia A; Zhao, Lanpo; Crawford, Patrice; Li, Mingtang

    2016-04-01

    The simulation of Cr(VI) behavior in an unsaturated zone and aquifer, using a 3D experimental set-up were performed to illustrate the distribution, transport and transformation of Cr(VI), and further to reveal the potential harm of Cr(VI) after entering the groundwater. The result indicated that chromium(VI) was transported in the vertical direction, meanwhile, was transported in the horizontal direction under the influence of groundwater flow. The direction and distance away from the pollution source zone had great effect on the chromium(VI) concentration. At the sampling sites near the pollution source zone, there was a sudden increase of chromium(VI) concentration. The concentration of chromium(III) concentration in some random effluent samples was not detected. Chromium had not only transported but also had fraction and specie transformation in the unsaturated zone and aquifer. The relative concentration of residue fraction chromium was decreased with time. The content of Fe-Mn oxide fraction chromium was increased with time. The relative content of exchangeable and carbonate-bound fraction chromium was lower and the content variations were not obvious. Chromium(VI) (91-98%) was first reduced to chromium(III) rapidly. The oxidation reaction occurred later and the relative content of chromium(VI) was increased again. The presence of manganese oxides under favorable soil conditions can promote the reoxidation of Cr(III) to Cr(VI).

  20. 75 FR 67100 - Superalloy Degassed Chromium From Japan

    Science.gov (United States)

    2010-11-01

    ... superalloy degassed chromium from Japan (70 FR 76030). The Commission is conducting a review to determine..., subparts A, D, E, and F (19 CFR part 207), as most recently amended at 74 FR 2847 (January 16, 2009). \\1... rule 201.15(b)(19 CFR 201.15(b)), 73 FR 24609 (May 5, 2008). This advice was developed in...

  1. 76 FR 8773 - Superalloy Degassed Chromium From Japan

    Science.gov (United States)

    2011-02-15

    ... applicable deadline.'' (75 FR 80457). Accordingly, pursuant to section 751(c) of the Tariff Act of 1930 (19 U... COMMISSION Superalloy Degassed Chromium From Japan AGENCY: United States International Trade Commission... Japan would be likely to lead to continuation or recurrence of material injury. On December 22,...

  2. Effects of chromium picolinate supplementation in type 2 diabetic patients

    Directory of Open Access Journals (Sweden)

    Niladê Rosinski Rocha

    2014-10-01

    Full Text Available The effects of chromium picolinate in Type 2 diabetic patients are investigated.  Seventeen Type 2 diabetic patients were randomly divided into two groups. The experimental group received fiber-rich hypocaloric diet and chromium picolinate whereas the control group received fiber-rich hypocaloric diet and placebo. The chromium picolinate was offered twice a day at the dose of 100 μg. Anthropometric data such as blood pressure, fasting glycemia and glycated hemoglobin (HbA1c were measured and these parameters were evaluated again after 90 days. No difference was reported in rates of body weight, waist, hip, body mass index, blood pressure and fasting glycemia (Control vs. Experimental groups after treatment. However, a decrease (p = 0.0405 of HbA1c occurred in the experimental group when the pre- and post-treatment rates were compared. HbA1c data showed that chromium picolinate improved the glycemic control in Type 2 diabetes.

  3. Cobalt chromium stents versus stainless steel stents in diabetic patients

    Directory of Open Access Journals (Sweden)

    Mahmoud Ahmed Tantawy

    2014-03-01

    Conclusions: We concluded that no significant statistical difference was found between the two stents (cobalt-chromium alloy bare metal stent versus conventional bare metal stainless steel stent in diabetic patients regarding (initial procedural success, in-hospital complications, the incidence of ISR at follow up, event-free survival at follow up.

  4. Domestic Production Issues in Chromium and Platinum-Group Metals

    Science.gov (United States)

    1988-09-01

    Protection Agency. OPA 87-005. Washington: Government Printing Office, May 1987. 16. Foley, Jeffrey Y. and James C. Barker . Chromite Deposits Along...Mining, Metallurgical, and Petroleum Engineers, 1976. 52. Stowe, Clive W. Evolution of Chromium Ore Fields. New York: Van Nostrand Reinhold Company

  5. Spin-wave and critical neutron scattering from chromium

    DEFF Research Database (Denmark)

    Als-Nielsen, Jens Aage; Axe, J.D.; Shirane, G.

    1971-01-01

    Chromium and its dilute alloys are unique examples of magnetism caused by itinerant electrons. The magnetic excitations have been studied by inelastic neutron scattering using a high-resolution triple-axis spectrometer. Spin-wave peaks in q scans at constant energy transfer ℏω could, in general, ...

  6. New alloys to conserve critical elements. [replacing chromium in steels

    Science.gov (United States)

    Stephens, J. R.

    1978-01-01

    Previous studies and surveys on availability of domestic reserves have shown that chromium is a most critical element within the U.S. metal industry. More precisely, the bulk of chromium is consumed in the production of stainless steels, specifically Type 304 stainless steel (304SS) which contains 18% Cr. The present paper deals with means of reducing chromium in commercial stainless steels by substituting more abundant or less expensive elements with the intent of maintaining the properties of 304SS. The discussion focuses on some of the oxidation and corrosion properties of new substitute stainless steels with only 12% Cr, which represents a potential saving of 33% of the chromium consumed in the production of 304SS. The alloying elements substituted for Cr in 304SS are selected according to their potential for protective oxide formation during high-temperature oxidation; these are Al, Si, Ti, Y, and misch metal which is 99.7% rare-earth metals containing 50 to 55% cerium. Other alloying elements to impart corrosion resistance are Mn, Mo, and V.

  7. Microbial biotechnology for remediation of aquatic habitats polluted with chromium

    Directory of Open Access Journals (Sweden)

    Viorica Coşier

    2008-12-01

    Full Text Available Chromium may occur in nine different forms of oxidation ranging from ?II to +VI, with forms II, III and VI as the most commonly encountered. In Cluj county, chromium pollution dates well back in time and has caused important dysfunction to the mechanical-biological wastewater purification station of the city of Cluj (Coşier & Diţă 1996. The purpose of this study was to develop one microbial method able to reduce hexavalent chromium (mobile, permeable to cell membrane, carcinogenic and mutagenic (Ishikawa et al 1994 to the trivalent form (insoluble and an essential element for humans (Song et al 2006. Different sources of chromium-reducing bacteria and many sources of carbon and energy added to the Kvasnikov mineral basal medium (Komori et al 1990 with increasing amount of chromate (200- 1000 mg/l were tested. Two bacterial strains, able to reduce even 1000 mg chromate/l, were isolated in pure culture. For one of these bacterial strains, we determined the optimum conditions for the reduction of Cr (VI.

  8. DANGER OF HEXAVALENT CHROMIUM AND STRATEGY FOR THE REMEDITATION

    Directory of Open Access Journals (Sweden)

    Aniruddha Roy

    2013-02-01

    Full Text Available Some metals as micronutrients have a major role in the life and growth process of plants and animals. However, certain forms of some metals may also act as toxic material even in relatively small quantities. Chromium is such a metal, whose concentration above a certain limit may cause a serious problem to the health of living organisms. Chromium (Cr may occur in several chemical forms in organic and inorganic systems. In biological systems only Cr (III and Cr (VI are significant. Among these two states, trivalent chromium (Cr-III is considered as an essential component, while hexavalent Chromium (Cr-VI in biological system has been detected as responsible for so many diseases, even some specific forms of cancer. This paper intends to present the adverse effect of Cr(VI on environment as well as on human beings and also try to find a way out to dissolve the problem by a newly developed efficient and cost effective technique.

  9. FEATURES OF CHROMIUM DOPING OF WEAR-RESISTANT CAST IRON

    Directory of Open Access Journals (Sweden)

    V. V. Netrebko

    2013-01-01

    Full Text Available The aim of this work analysis of the influence of chromium on the process of carbide formation, changes in chemical composition of the metal substrate in the areas adjacent to the carbides and at the hardness of iron while economy nickel and manganesealloying.

  10. Structure and morphology studies of chromium film at elevated temperature in hypersonic environment

    Indian Academy of Sciences (India)

    G M Hegde; V Kulkarni; M Nagaboopathy; K P J Reddy

    2012-06-01

    This paper presents the after shock heated structural and morphological studies of chromium film coated on hypersonic test model as a passive drag reduction element. The structural changes and the composition of phases of chromium due to shock heating (2850 K) are characterized using X-ray diffraction studies. Surface morphology changes of chromium coating have been studied using scanning electron microscopy (SEM) before and after shock heating. Significant amount of chromium ablation and sublimation from the model surface is noticed from SEM micrographs. Traces of randomly oriented chromium oxides formed along the coated surface confirm surface reaction of chromium with oxygen present behind the shock. Large traces of amorphous chromium oxide phases are also observed.

  11. Ailanthus Altissima and Phragmites Australis for chromium removal from a contaminated soil.

    Science.gov (United States)

    Ranieri, Ezio; Fratino, Umberto; Petrella, Andrea; Torretta, Vincenzo; Rada, Elena Cristina

    2016-08-01

    The comparative effectiveness for hexavalent chromium removal from irrigation water, using two selected plant species (Phragmites australis and Ailanthus altissima) planted in soil contaminated with hexavalent chromium, has been studied in the present work. Total chromium removal from water was ranging from 55 % (Phragmites) to 61 % (Ailanthus). After 360 days, the contaminated soil dropped from 70 (initial) to 36 and 41 mg Cr/kg (dry soil), for Phragmites and Ailanthus, respectively. Phragmites accumulated the highest amount of chromium in the roots (1910 mg Cr/kg(dry tissue)), compared with 358 mg Cr/kg(dry tissue) for Ailanthus roots. Most of chromium was found in trivalent form in all plant tissues. Ailanthus had the lowest affinity for Cr(VI) reduction in the root tissues. Phragmites indicated the highest chromium translocation potential, from roots to stems. Both plant species showed good potentialities to be used in phytoremediation installations for chromium removal.

  12. Bioaccumulation and depuration of chromium in the selected organs and whole body tissues of freshwater fish Cirrhinus mrigala individually and in binary solutions with nickel

    Institute of Scientific and Technical Information of China (English)

    PL. RM. Palaniappan; S. Karthikeyan

    2009-01-01

    Contamination of aquatic ecosystems with heavy metals has been receiving increased worldwide attention due to their harmful effects on human health and other organisms in the environment.Most of the studies dealing with toxic effects of metals deal with single metal species, while the aquatic organisms are typically exposed to mixtures of metals.Hence, in order to provide data supporting the usefulness of freshwater fish as indicators of heavy metal pollution, it has been proposed in the present study to investigate the bioaccumulation and depuration of chromium in the selected organs of freshwater fingerlings Cirrhinus mrigala, individually and in binary solutions with nickel.The results show that the kidney is a target organ for chromium accumulation, which implies that it is also the "critical" organ for toxic symptoms.The results further show that accumulation of nickel in all the tissues of C.mrigala is higher than that of chromium.In addition, the metal accumulations of the binary mixtures of chromium and nickel are substantially higher than those of the individual metals, indicating synergistic interactions between the two metals.Theoretically the simplest explanation for an additive joint action of toxicants in a mixture is that they act in a qualitatively similar way.The observed data suggest that C.mrigala could be suitable monitoring organisms to study the bioavailability of water-bound metals in freshwater habitats.

  13. Laboratory scale studies on removal of chromium from industrial wastes

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    Chromium being one of the major toxic pollutants is discharged from electroplating and chrome tanning processes and is also found in the effluents of dyes, paint pigments, manufacturing units etc. Chromium exists in aqueous systems in both trivalent (Cr 3+) and hexavalent (Cr 6+) forms. The hexavalent form is carcinogenic and toxic to aquatic life, whereas Cr3+ is however comparatively less toxic. This study was undertaken to investigate the total chromium removal from industrial effluents by chemical means in order to achieve the Pakistan NEQS level of 1 mg/L by the methods of reduction and precipitation. The study was conducted in four phases.In phase I, the optimum pH and cost effective reducing agent among the four popular commercial chemicals was selected. As a result, pH of 2 was found to be most suitable and sodium meta bisulfate was found to be the most cost effective reducing agent respectively. Phase II showed that lower dose of sodium meta bisulfate was sufficient to obtain 100 % efficiency in reducing Cr6+ to Cr3+, and it was noted that reaction time had no significance in the whole process. A design curve for reduction process was established which can act as a tool for treatment of industrial effluents.Phase III studies indicated the best pH was 8.5 for precipitation of Cr 3+ to chromium hydroxide by using lime. An efficiency of 100 % was achievable and a settling time of 30 minutes produced clear effluent. Finally in Phase IV actual waste samples from chrome tanning and electroplating industries, when precipitated at pH of 12 gave 100 % efficiency at a settling time of 30 minutes and confirmed that chemical means of reduction and precipitation is a feasible and viable solution for treating chromium wastes from industries.

  14. Activated carbon adsorption for chromium treatment and recovery; Adsorbimento di cromo su carboni attivi a scopo di recupero e decontaminazione

    Energy Technology Data Exchange (ETDEWEB)

    Baroncelli, F.; Castelli, S.; De Francesco, M. [ENEA, Casaccia (Italy). Area Energia e Innovazione

    1994-05-01

    The capability of actived carbon systems to adsorb chromium from wastewater of galvanic industry is valued. Batch tests and column tests are carried out with good results. An activated carbon with acidic surface oxides can adsorb both chromate and chromium (III); chromate is reduced in situ and then adsorbed as chromium (III). Chromium can be desorbed from carbon by an acid or basic treatment obtaining respectively chromium (III) or chromate solutions. Carbon can be regenerated many times without evident signs of deterioration.

  15. Reduction of hexavalent chromium by ferrous iron: A process of chromium isotope fractionation and its relevance to natural environments

    DEFF Research Database (Denmark)

    Døssing, Lasse Nørbye; Dideriksen, Knud; Stipp, Susan Louise Svane;

    2011-01-01

    Stable chromium (Cr) isotopes can be used as a tracer for changing redox conditions in modern marine systems and in the geological record. We have investigated isotope fractionation during reduction of Cr(VI)aq by Fe(II)aq. Reduction of Cr(VI)aq by Fe(II)aq in batch experiments leads to significant...

  16. Raman spectroscopy of supported chromium oxide catalysts : determination of chromium-oxygen bond distances and bond orders

    NARCIS (Netherlands)

    Weckhuysen, B.M.; Wachs, I.E.

    1996-01-01

    An empirical correlation is described for relating Raman stretching frequencies of chromium—oxygen (Cr—O) bonds to their bond lengths in chromium oxide reference compounds. An exponential fit of crystallographically determined Cr—O bond lengths to Cr—O Raman symmetric stretching frequencies (800–130

  17. Chromium removal from water by activated carbon developed from waste rubber tires.

    Science.gov (United States)

    Gupta, Vinod Kumar; Ali, Imran; Saleh, Tawfik A; Siddiqui, M N; Agarwal, Shilpi

    2013-03-01

    Because of the continuous production of large amount of waste tires, the disposal of waste tires represents a major environmental issue throughout the world. This paper reports the utilization of waste tires (hard-to-dispose waste) as a precursor in the production of activated carbons (pollution-cleaning adsorbent). In the preparation of activated carbon (AC), waste rubber tire (WRT) was thermally treated and activated. The tire-derived activated carbon was characterized by means of scanning electron microscope, energy-dispersive X-ray spectroscopy, FTIR spectrophotometer, and X-ray diffraction. In the IR spectrum, a number of bands centred at about 3409, 2350, 1710, 1650, and 1300-1000 cm(-1) prove the present of hydroxyl and carboxyl groups on the surface of AC in addition to C═C double bonds. The developed AC was tested and evaluated as potential adsorbent removal of chromium (III). Experimental parameters, such as contact time, initial concentration, adsorbent dosage and pH were optimized. A rapid uptake of chromium ions was observed and the equilibrium is achieved in 1 h. It was also found that the adsorption process is pH dependent. This work adds to the global discussion of the cost-effective utilization of waste rubber tires for waste water treatment.

  18. Supercritical water oxidation of tannery sludge: stabilization of chromium and destruction of organics.

    Science.gov (United States)

    Zou, Daoan; Chi, Yong; Dong, Jun; Fu, Chao; Wang, Fei; Ni, Mingjiang

    2013-10-01

    The supercritical water oxidation (SCWO) of industrial tannery sludge was investigated to understand the simultaneous destruction of organic pollutants and recovery of high content chromium. Experiments were performed in a batch reactor at temperatures of 350-500 °C, reaction time of 150-300 s and different oxygen ratios, to exhibit the effect of operation conditions. Results showed that removal efficiency of chemical oxygen demand (COD) increased with higher temperature, larger oxidant amount and reaction time; a maximum value of 96% was obtained. Meanwhile, destruction yield was much higher under supercritical conditions than that in subcritical water. In addition, removal efficiency of Cr from sludge reached more than 98% under all conditions; higher temperature played a positive role. Further, leaching toxicity tests of heavy metals in solid products were conducted based on toxicity characteristic leaching procedure. All heavy metals except nickel showed a greatly reduced leaching toxicity through their stabilization. The chromium oxide recovered in ash was amorphous below 550 °C, so that the structure of Cr could not be identified by X-ray diffraction pattern. Special attention should be paid on nickel as its leaching toxicity increased due to the corrosion of reactor surface under severe reaction conditions.

  19. DRY AND WET GRINDING KINETICS OF CHROMIUM ORE AND EFFECT OF PULP DENSITY

    Directory of Open Access Journals (Sweden)

    Alper ÖZKAN

    2006-01-01

    Full Text Available In this study, the kinetics of dry and wet grinding of various feed sizes of chromium ore has been determined using a laboratory scale ceramic ball mill. In addition, the effect of pulp density on the spesific rate of breakage (Si and net production rate to finer than specified size were investigated. The dry and wet grinding of all the size intervals of chromium ore followed the first-order breakage law, and the Si values increased as the feed sizes became coarser. Moreover, the wet grinding of these various feed sizes gave higher Si values by a factor of 2.0 to 2.6 comparing to the dry Si values. From the experimental studies performed on the effect of pulp density on the grinding process, the highest Si value was obtained at a pulp density of 45 % solids by volume. At the same pulp density value, the rate of net production of -75 µm particle size also reached the highest value.

  20. Effect of preferential dissolution on erosion-corrosion for chromium steel in alkali slurry

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    An investigation was carried out concerning the effect of preferential dissolution on the erosion-corrosion for a chromium steel in 1mol/L NaOH. Preliminary tests using a potentiodynamic technique were performed in order to establish the presence of preferential dissolution in the alkali solution with and without the alumina particles at different rotation speeds. For purposes of quantifying the observed phenomena a potentiostatic mass loss method was also used. The results show that the active peaks occur at potential between +0.4 and +0.5V on the polarization curves, which indicates that there is a preferential dissolution for chromium steel under erosion-corrosion conditions and the ferrite phase acts as a sacrificial anode in favor of (Fe,Cr)7C3 phase. Addition of particles can promote the preferential dissolution at different rotation speeds. The combined effects of erosion-corrosion results in total mass loss rates to be greater than the sum effects of each process taken alone, thus showing a strong synergism between erosion and corrosion due to preferential dissolution.

  1. The influence of chromium on mechanical properties of austempered ductile cast iron

    Science.gov (United States)

    Bartosiewicz, L.; Singh, I.; Alberts, F. A.; Krause, A. R.; Putatunda, S. K.

    1995-02-01

    An investigation was carried out to examine the influence of microstructure and chromium on the tensile properties and plane strain fracture toughness of austempered ductile cast iron (ADI). The investigation also examined the growth kinetics of ferrite in these alloys. Compact tension and round cylindrical tensile specimens were prepared from ductile cast iron with Cr as well as without Cr. These specimens were then given four different heat treatments to produce four different microstructures. Tensile tests and fracture toughness tests were carried out as per ASTM standards E-8 and E-399. The crack growth mechanism during fracture toughness tests was also determined. The test results indicate that yield strength, tensile strength, and fracture toughness of ADI increases with an increase in the volume fractions of ferrite, and the fracture toughness reaches a peak when the volume fractions of the ferrite are approximately 60% in these alloys. The Cr addition was found to reduce the fracture toughness of ADI at lower hardness levels (<40 HRC); at higher hardness levels (≥40 HRC), the effect of chromium on the fracture toughness was negligible. The crack growth mechanism was found to be a combination of quasi-cleavage and microvoid coalescences, and the crack trajectories connect the graphite nodules along the way.

  2. MICROBIAL LEACHING OF CHROMIUM FROM SOLIDIFIED WASTE FORMS – A KINETIC STUDY

    Directory of Open Access Journals (Sweden)

    Carmalin Sophia Ayyappan

    2015-06-01

    Full Text Available In this study, Thiobacillus thiooxidans (T. thiooxidans was used to study the microbial stability / degradation of cement-based waste forms. The waste forms contained a chromium salt (CrCl3·6H2O, cement and other additives viz., lime and gypsum in two different proportions. The experimental samples of all the simulated waste forms showed evidence of microbial growth as indicated by substantial increase in sulfate. Chromium leached from the waste forms was found to be lowest in cement – lime solidified waste forms (0.061 mg·l-1 and highest in cement gypsum waste forms (0.22 mg·l-1 after 30 days of exposure. These values were lower than the toxicity characteristic leaching procedure (TCLP, regulatory limit (5 mg·l-1. Model equations based on two shrinking core models (acid dissolution and bulk diffusion model, were used to analyze the kinetics of microbial degradation of cement based waste forms. The bulk diffusion model was observed to fit the data better than the acid dissolution model, as indicated by good correlation coefficients.

  3. Effects of Si on the Microstructures and Mechanical Properties of High-Chromium Cast Iron

    Science.gov (United States)

    Lai, J. P.; Pan, Q. L.; Peng, H. J.; Cui, H. R.; Xiao, C. A.

    2016-11-01

    Effect of Si on the microstructures and mechanical properties of high-chromium cast iron was investigated. The eutectic carbides are refined greatly and a transformation of matrix from austenitic matrix to pearlite is observed with increase in Si content from 0.5 to 1.5 wt.%. The refinement of eutectic microstructure is attributed to the decrease in the eutectic temperature, while the transformation from austenite matrix to pearlite is associated with the increase in solubility of carbon in the matrix. In the pearlite matrix, two types of pearlite are observed: one with lamellar pearlite, distributing at the periphery, and the second one with granular pearlite at the center. The density of secondary carbides precipitated from the matrix increases greatly with addition of Si from 0.5 to 1.5 wt.%, which is associated with more carbon and chromium elements confined in the matrix in the alloy containing 1.5 wt.%. More rod-like particles are observed in the alloy containing 0.5 wt.% Si, while the morphology of secondary carbides of alloy containing 1.5 wt.% is granular. The mechanical properties are improved with a 7% increase in tensile strength from 586 to 626 MPa and impact toughness from 5.8 to 7.3 J cm-2.

  4. Zinc-oxide charge trapping memory cell with ultra-thin chromium-oxide trapping layer

    Directory of Open Access Journals (Sweden)

    Nazek El-Atab

    2013-11-01

    Full Text Available A functional zinc-oxide based SONOS memory cell with ultra-thin chromium oxide trapping layer was fabricated. A 5 nm CrO2 layer is deposited between Atomic Layer Deposition (ALD steps. A threshold voltage (Vt shift of 2.6V was achieved with a 10V programming voltage. Also for a 2V Vt shift, the memory with CrO2 layer has a low programming voltage of 7.2V. Moreover, the deep trapping levels in CrO2 layer allows for additional scaling of the tunnel oxide due to an increase in the retention time. In addition, the structure was simulated using Physics Based TCAD. The results of the simulation fit very well with the experimental results providing an understanding of the charge trapping and tunneling physics.

  5. Zinc-oxide charge trapping memory cell with ultra-thin chromium-oxide trapping layer

    Energy Technology Data Exchange (ETDEWEB)

    El-Atab, Nazek; Rizk, Ayman; Nayfeh, Ammar [Institute Center for Microsystems – iMicro, Department of Electrical Engineering and Computer Science (EECS), Masdar Institute of Science and Technology Abu Dhabi (United Arab Emirates); Okyay, Ali K. [Department of Electrical and Electronics Engineering, Bilkent University, 06800 Ankara (Turkey); UNAM-National Nanotechnology Research Center and Institute of Materials Science and Nanotechnology, Bilkent University, 06800 Ankara (Turkey)

    2013-11-15

    A functional zinc-oxide based SONOS memory cell with ultra-thin chromium oxide trapping layer was fabricated. A 5 nm CrO{sub 2} layer is deposited between Atomic Layer Deposition (ALD) steps. A threshold voltage (V{sub t}) shift of 2.6V was achieved with a 10V programming voltage. Also for a 2V V{sub t} shift, the memory with CrO{sub 2} layer has a low programming voltage of 7.2V. Moreover, the deep trapping levels in CrO{sub 2} layer allows for additional scaling of the tunnel oxide due to an increase in the retention time. In addition, the structure was simulated using Physics Based TCAD. The results of the simulation fit very well with the experimental results providing an understanding of the charge trapping and tunneling physics.

  6. Zinc-oxide charge trapping memory cell with ultra-thin chromium-oxide trapping layer

    Science.gov (United States)

    El-Atab, Nazek; Rizk, Ayman; Okyay, Ali K.; Nayfeh, Ammar

    2013-11-01

    A functional zinc-oxide based SONOS memory cell with ultra-thin chromium oxide trapping layer was fabricated. A 5 nm CrO2 layer is deposited between Atomic Layer Deposition (ALD) steps. A threshold voltage (Vt) shift of 2.6V was achieved with a 10V programming voltage. Also for a 2V Vt shift, the memory with CrO2 layer has a low programming voltage of 7.2V. Moreover, the deep trapping levels in CrO2 layer allows for additional scaling of the tunnel oxide due to an increase in the retention time. In addition, the structure was simulated using Physics Based TCAD. The results of the simulation fit very well with the experimental results providing an understanding of the charge trapping and tunneling physics.

  7. Study of a New Chromium-Free Conversion Coating Formed on ZnAl Alloy

    Institute of Scientific and Technical Information of China (English)

    LONG Jin-ming; GUO Zhong-cheng; HAN Xia-yun; YANG Ning

    2004-01-01

    A new chromium-free conversion film was obtained on surface of a ZnAl alloy by chemical conversion process.Influence of the additives in treating solution containing cerium salt on the corrosion protection of the conversion film formed on zinc alloy was investigated. Corrosion tests and electrochemical measurements in sodium chloride solution were performed. The microstructure and composition of the coatings were examined by means of SEM, EDS and XRD. It was found that the corrosion protection capabilities of the conversion film are markedly increased with the cerium nitride plus additives (hydrogen fluoride acid and an organic inhibitor) treating process. The modified conversion film is an organic/inorganic composite coating and is much more corrosion resistant than the conventional chromate conversion coating and the single cerium conversion coating.

  8. Study of a New Chromium-Free Conversion Coating Formed on ZnAl Alloy

    Institute of Scientific and Technical Information of China (English)

    LONGJin-ming; GUOZhong-cheng; HANXia-yun; YANGNing

    2004-01-01

    A new chromium-free conversion film was obtained on surface of a ZnA1 alloy by chemical conversion process. Influence of the additives in treating solution containing cerium salt on the corrosion protection of the conversion film formed on zinc alloy was investigated. Corrosion tests and electrochemical measurements in sodium chloride solution were performed. The microstructure and composition of the coatings were examined by means of SEM, EDS and XRD. It was found that the corrosion protection capabilities of the conversion film are markedly increased with the cerium nitride plus additives (hydrogen fluoride acid and an organic inhibitor) treating process. The modified conversion film is an organic/inorganic composite coating and is much more corrosion resistant than the conventional chromate conversion coating and the single cerium conversion coating.

  9. Hexavalent chromium reduction in contaminated soil: A comparison between ferrous sulphate and nanoscale zero-valent iron.

    Science.gov (United States)

    Di Palma, L; Gueye, M T; Petrucci, E

    2015-01-01

    Iron sulphate (FeSO4) and colloidal nano zero-valent iron (nZVI) as reducing agents were compared, with the aim of assessing their effectiveness in hexavalent chromium [Cr(VI)] removal from a contaminated industrial soil. Experiments were performed on soil samples collected from an industrial site where a nickel contamination, caused by a long-term productive activity, was also verified. The influence of reducing agents amount with respect to chromium content and the effectiveness of deoxygenation of the slurry were discussed. The soil was fully characterized before and after each test, and sequential extractions were performed to assess chemico-physical modifications and evaluate metals mobility induced by washing. Results show that both the reducing agents successfully lowered the amount of Cr(VI) in the soil below the threshold allowed by Italian Environmental Regulation for industrial reuse. Cr(VI) reduction by colloidal nZVI proved to be faster and more effective: the civil reuse of soil [Cr(VI)hydroxide fraction, thus confirming a mechanism of chromium-iron hydroxides precipitation. In addition, a decrease of nickel (Ni) and lead (Pb) content in soil was also observed when acidic conditions were established.

  10. A computational investigation of boron-doped chromium and chromium clusters by density functional theory

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    The geometries,stabilities and electronic properties of Crn and CrnB(n=2-9) clusters have been systematically investigated by density functional theory.The results suggest that the lowest energy structures for CrnB clusters can be obtained by substituting one Cr atom in Crn+1 clusters with B atom.The geometries of CrnB clusters are similar to that of Crn+1 clusters except for local structural distortion.The second-order difference and fragmentation energy show Cr4,Cr6,Cr8,Cr3B,Cr5B and Cr8B cluster are the most stable among these studied clusters.The impurity B increases the stabilities of chromium cluster.When B is doped on the Crn clusters,cluster geometry does dominate positive role in enhancing their stability.The doped B atom does not change the coupling way of the Cr site in Crn clusters,but breaks the symmetry and the Cr atoms are no longer equivalent.The doped B atom increases the total magnetic moments of Crn in most cases.

  11. Urinary levels of nickel and chromium associated with dental restoration by nickel-chromium based alloys

    Institute of Scientific and Technical Information of China (English)

    Bo Chen; Gang Xia; Xin-Ming Cao; Jue Wang; Bi-Yao Xu; Pu Huang; Yue Chen; Qing-Wu Jiang

    2013-01-01

    This paper aims to investigate if the dental restoration of nickel-chromium based alloy (Ni-Cr) leads to the enhanced excretions of Ni and Cr in urine. Seven hundred and ninety-five patients in a dental hospital had single or multiple Ni-Cr alloy restoration recently and 198 controls were recruited to collect information on dental restoration by questionnaire and clinical examination. Urinary concentrations of Ni and Cr from each subject were measure by graphite furnace atomic absorption spectrometry. Compared to the control group, the urinary level of Ni was significantly higher in the patient group of 〈 1 month of the restoration duration, among which higher Ni excretions were found in those with either a higher number of teeth replaced by dental alloys or a higher index of metal crown not covered with the porcelain. Urinary levels of Cr were significantly higher in the three patient groups of 〈1, 1 to 〈3 and 3 to 〈6 months, especially in those with a higher metal crown exposure index. Linear curve estimations showed better relationships between urinary Ni and Cr in patients within 6-month groups. Our data suggested significant increased excretions of urinary Ni and Cr after dental restoration. Potential short- and long-term effects of Ni-Cr alloy restoration need to be investigated.

  12. A metastable chromium carbide powder obtained by carburization of a metastable chromium oxide

    Energy Technology Data Exchange (ETDEWEB)

    Loubiere, S. [Univ. Paul-Sabatier, Toulouse (France). Lab. de Chimie des Materiaux Inorganique; Laurent, C. [Univ. Paul-Sabatier, Toulouse (France). Lab. de Chimie des Materiaux Inorganique; Bonino, J.P. [Univ. Paul-Sabatier, Toulouse (France). Lab. de Chimie des Materiaux Inorganique; Rousset, A. [Univ. Paul-Sabatier, Toulouse (France). Lab. de Chimie des Materiaux Inorganique

    1996-10-15

    A metastable Cr{sub 3}C{sub 2-x} carbide powder is prepared by carburization of a metastable chromium oxide in H{sub 2}-CH{sub 4} atmosphere under the appropriate conditions (temperature, dwell time and CH{sub 4} content). A very high specific surface area (greater than 210 m{sup 2} g{sup -1}) of the starting oxide is necessary to avoid the formation of the sole stable Cr{sub 3}C{sub 2} phase. The transformation from the stable Cr{sub 3}C{sub 2} to the metastable Cr{sub 3}C{sub 2-x} is observed for the first time. The driving force could be an epitaxial effect between Cr{sub 3}C{sub 2-x} and the surrounding graphite layer. This is consistent with the observation that the formation of graphite layers by CH{sub 4} cracking is easier in the Cr{sub 3}C{sub 2-x}-containing powders. (orig.)

  13. Chromium(VI) but not chromium(III) species decrease mitoxantrone affinity to DNA.

    Science.gov (United States)

    Nowicka, Anna M; Stojek, Zbigniew; Hepel, Maria

    2013-01-31

    Binding of mitoxantrone (MXT) to double-stranded DNA has been investigated as a model drug-DNA binding system to evaluate the effects of various forms of chromium on the binding properties. We have found that Cr(III), which binds strongly to DNA, does not affect the MXT affinity to DNA. In contrast, Cr(VI), in the form of chromate ions CrO(4)(2-), decreases the MXT affinity to DNA despite electrostatic repulsions with phosphate-deoxyribose chains of DNA. The MXT-DNA binding constant was found to decrease from (1.96 ± 0.005) × 10(5) to (0.77 ± 0.018) × 10(5) M(-1) for Cr(VI) concentration changing from 0 to 30 μM. The influence of Cr(VI) on MXT-DNA binding has been attributed to the oxidation of guanine residue, thus interrupting the intercalation of MXT into the DNA double helix at the preferential CpG intercalation site. This supposition is corroborated by the observed increase in the MXT binding site size from 2 bp (base pairs) to 4-6 bp in the presence of Cr(VI). The measurements of the MXT-DNA binding constant and the MXT binding site size on a DNA molecule have been carried out using spectroscopic, voltammetric, and nanogravimetric techniques, providing useful information on the mechanism of the interactions.

  14. Maximum availability and mineralogical control of chromium released from AOD slag.

    Science.gov (United States)

    Li, Junguo; Liu, Bao; Zeng, Yanan; Wang, Ziming; Gao, Zhiyuan

    2017-03-01

    AOD (argon oxygen decarburization) slag is the by-product in the stainless steel refining process. Chromium existing in AOD slag can leach out and probably poses a serious threat to the environment. To assess the leaching toxicity of chromium released from AOD slag, the temperature-dependent maximum availability leaching test was performed. To determine the controlling mineralogical phases of chromium released from AOD slag, a Visual MINTEQ simulation was established based on Vminteq30 and the FactSage 7.0 database. The leaching tests indicated that the leaching availability of chromium was slight and mainly consisted of trivalent chromium. Aging of AOD slag under the atmosphere can oxidize trivalent chromium to hexavalent chromium, which could be leached out by rainwater. According to the simulation, the chromium concentration in leachates was controlled by the freely soluble pseudo-binary phases in the pH = 7.0 leaching process and controlled by the Cr2O3 phase in the pH = 4.0 leaching process. Chromium concentrations were underestimated when the controlling phases were determined to be FeCr2O4 and MgCr2O4. Facilitating the generation of the insoluble spinel-like phases during the cooling and disposal process of the molten slag could be an effective approach to decreasing the leaching concentration of chromium and its environmental risk.

  15. Hexavalent chromium exposure and control in welding tasks.

    Science.gov (United States)

    Meeker, John D; Susi, Pam; Flynn, Michael R

    2010-11-01

    Studies of exposure to the lung carcinogen hexavalent chromium (CrVI) from welding tasks are limited, especially within the construction industry where overexposure may be common. In addition, despite the OSHA requirement that the use of engineering controls such as local exhaust ventilation (LEV) first be considered before relying on other strategies to reduce worker exposure to CrVI, data on the effectiveness of LEV to reduce CrVI exposures from welding are lacking. The goal of the present study was to characterize breathing zone air concentrations of CrVI during welding tasks and primary contributing factors in four datasets: (1) OSHA compliance data; (2) a publicly available database from The Welding Institute (TWI); (3) field survey data of construction welders collected by the Center for Construction Research and Training (CPWR); and (4) controlled welding trials conducted by CPWR to assess the effectiveness of a portable LEV unit to reduce CrVI exposure. In the OSHA (n = 181) and TWI (n = 124) datasets, which included very few samples from the construction industry, the OSHA permissible exposure level (PEL) for CrVI (5 μg/m(3)) was exceeded in 9% and 13% of samples, respectively. CrVI concentrations measured in the CPWR field surveys (n = 43) were considerably higher, and 25% of samples exceeded the PEL. In the TWI and CPWR datasets, base metal, welding process, and LEV use were important predictors of CrVI concentrations. Only weak-to-moderate correlations were found between total particulate matter and CrVI, suggesting that total particulate matter concentrations are not a good surrogate for CrVI exposure in retrospective studies. Finally, in the controlled welding trials, LEV reduced median CrVI concentrations by 68% (p = 0.02). In conclusion, overexposure to CrVI in stainless steel welding is likely widespread, especially in certain operations such as shielded metal arc welding, which is commonly used in construction. However, exposure could be

  16. Transformation behavior in low carbon 13% chromium-3% copper stainless steel; Tei C-13%Cr-3%Cu ko no hentai kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Hara, T.; Uemori, R.; Miyasaka, A. [Nippon Steel Corp., Tokyo (Japan)

    2000-10-01

    Martensitic transformation and {gamma} {yields} {alpha} transformation behavior were investigated in low carbon 13% chromium stainless steels containing 2% nickel or 3% copper. The main conclusions are as follows: (1) Hardness of 2% nickel added low carbon 13% chromium steel was independent of cooling rate after hot working at large reduction. Structure of the steel was martensitic even after being subjected to such large reduction of 75%. This result suggests that ferritic transformation was hard to occur under an usual cooling rate because austenite phase was sufficiently stablized by the addition of chromium and nickel. (2) Austenite to ferrite transformation occurred only for the low carbon 13% chromium 3% copper steel without nickel even at the small cooling rate, such as 0.01K/s. This result was mainly attributed to the unstabilization of austenite phase which caused by the precipitation of {epsilon}-Cu. Furthermore, austenite of the steel becomes easy to transform to ferrite due to heavy hot working. This phenomenon was seemed to be caused by the increase in the area of austenite grain boundary owing to recrystallization. Thus, it was considered that the nucleation of {epsilon}-Cu at the grain boundaries promoted ferrite formation. (author)

  17. A FACTORIAL DESIGN APPLIED TO THE STUDY OF CHROMIUM TOXICITY ON THE GLUTATHIONE LEVELS OF Brachiaria brizantha AND Brachiaria ruziziensis SEEDLINGS

    Directory of Open Access Journals (Sweden)

    Rafael Marques

    2015-08-01

    Full Text Available Chromium toxicity affects redox reactions within plant cells, generating detrimental reactive oxygen species. Glutathione is an antioxidant peptide and also a substrate for the production of phytochelatins, which are chelating peptides reported to mitigate Cr3+ toxicity in plants. In this study, Brachiaria brizantha (B. brizantha and Brachiaria ruziziensis (B. ruziziensis seedlings were evaluated for physiological responses and glutathione production following the addition of zero or 5 mg L-1 Cr3+ to the nutrient solution. Glutathione levels were determined by colorimetric analysis at 412 nm using 5,5'-dithio-bis(2-nitrobenzoic acid as a chromophore reagent and recovery with glutathione reductase (with evaluations at days 10 and 20 of continuous growth. The assessments were carried out in a completely randomized design with 2 authentic replications, and arranged in a 23 factorial. Cr3+ caused an average increase of 0.76 mg g-1 in the initial glutathione content. However, by day 20 there was an average reduction of 3.63 mg g-1. Chromium-affected physiological detrimental responses, albeit detected in both species, were less-pronounced in B. ruziziensis, along with a much higher level of glutathione. This study indicates that B. ruziziensis has a greater tolerance for chromium toxicity than B. brizantha, and that glutathione is likely to be involved in the mitigation of chromium stress in B. ruziziensis.

  18. Accurate quantification of total chromium and its speciation form Cr(VI) in water by ICP-DRC-IDMS and HPLC/ICP-DRC-IDMS.

    Science.gov (United States)

    Markiewicz, Barbara; Komorowicz, Izabela; Barałkiewicz, Danuta

    2016-05-15

    Two analytical procedures have been developed for the determination of total chromium (TCr) and its highly toxic species, i.e. Cr(VI) in water samples using the following methods: inductively coupled plasma dynamic reaction cell isotope dilution mass spectrometry (ICP-DRC-IDMS) and high performance liquid chromatography inductively coupled plasma dynamic reaction cell isotope dilution mass spectrometry (HPLC/ICP-DRC-IDMS). Spectral interferences, predominantly occurring in chromium determination, were removed using a dynamic reaction cell (DRC). The presented procedures facilitate the quantification of trace amounts - below 1 µg L(-1) of TCr and individual Cr species - in various water matrices including drinking water and still bottled water with different mineral composition. Special attention has been paid to the adequate preparation of isotopically enriched (53)Cr(VI) standard solution in order to avoid artifacts in chromium speciation. Both procedures were fully validated as well as establishing the traceability and estimation of the uncertainty of measurement were carried out. Application of all of the above mentioned elements and of the isotope dilution technique, which provides the highest quality of metrological traceability, allowed to obtain reliable and high quality results of chromium determination in water samples. Additionally, the comparison of two methods: HPLC/ICP-DRC-MS and HPLC/ICP-DRC-IDMS for Cr(VI) determination, was submitted basing on the validation parameters. As a result, the lower values for these parameters were obtained using the second method.

  19. Removal of Chromium with The Complexing Agents from Industrial Effluents

    Directory of Open Access Journals (Sweden)

    J. L. Prameena Sheeja

    2016-08-01

    Full Text Available Human activities and consequent developments have brought about the spectre of an overwhelming degradation of all facets of the natural environment-physical, chemical, biological and social. Environmental pollution, especially by chemicals, is one of the most significant factors in the degradation of the biosphere components. Among all chemical contaminants, heavy metals are believed to be of special ecological, biological and health significance. Unlike organic pollutants, the majority of which are susceptible to biological degradation, metal ions do not degrade into harmless end products. Chemical precipitation is a simple and economical method, and hence, has been widely used. The reduction of chromium (VI to chromium (III can be done with the help of ferrous sulphate. The precipitation was carried out in the presence and absence of complexing agents such as ammonium chloride, tartrate and citrate.

  20. Internal Friction In The PFN Ceramics With Chromium Dopand

    OpenAIRE

    Zachariasz R.; Bochenek D.; Bruś B.

    2015-01-01

    An aim of this work was to determine an influence of an admixture, the chromium (for x from 0.01 to 0.06), on the mechanical properties of the PFN ceramics. The ceramics with chemical composition Pb(Fe0.5−xCrxNb0.5)O3 was synthesized in two steps from simple oxides PbO, Fe2O3, Nb2O5, Cr2O3. The first stage was based on obtaining the FeNbO4 from the Fe2O3 and Nb2O5 simple oxides. At this stage an admixture in a form the Cr2O3 chromium oxide was added to the solution. In the second stage the Pb...

  1. Preparation of Silica Modified with 2-Mercaptoimidazole and its SorptionProperties of Chromium(III

    Directory of Open Access Journals (Sweden)

    Harry Budiman

    2009-01-01

    Full Text Available Modified silica gel was prepared to remove the heavy metal of chromium(III from water sample. Silica gel was used as supporting material and the 2-mercaptoimidazole was immobilized onto surface silica so that the silica would have selective properties to adsorb the heavy metal chromium(III through the formation of coordination compound between the 2-mercaptoimidazole and chromium(III. The characterization of modified silica gel was carried out by analyzing the Fourier Transform Infrared Spectrum of this material in order to ensure the immobilization of 2-mercaptoimidazole onto the surface. The effect of pH solution, initial concentration of chromium(III, and interaction time were investigated in batch mode to find the adsorption properties of chromium(III onto modified silica. The condition optimum of these parameters was applied to determine the removal percentage of chromium(III in water sample using the modified silica gel

  2. Biological monitoring of occupational exposure to different chromium compounds at various valency states

    Energy Technology Data Exchange (ETDEWEB)

    Mutti, A.; Pedroni, C.; Arfini, G.; Franchini, I.; Minoia, C.; Micoli, G.; Baldi, C.

    1984-01-01

    Chromium concentrations in the air were measured in seven different workroom environments, where exposure to water soluble hexavalent or trivalent compounds was expected. Urinary excretion of chromium was measured before and after the same arbitrarily chosen working day. End-of-shift urinary chromium and its increase above pre-exposure levels were closely related to the concentration of water soluble chromium (VI) in the air. The values corresponding to 50 micrograms m-3 in the air, which is the current threshold limit value in most countries, were 29.8 and 12.2 micrograms g-1 of creatinine, respectively. Urinary chromium in workers exposed to water insoluble chromates or to water soluble chromic (III) sulphate was definitely higher than that observed in subjects not occupationally exposed to chromium compounds, but it cannot be recommended as short-term exposure test for evaluation of the job-related hazard.

  3. Bioconcentration of chromium in edible mushrooms: influence of environmental and genetic factors.

    Science.gov (United States)

    García, M A; Alonso, J; Melgar, M J

    2013-08-01

    Chromium concentrations were determined in 167 samples of wild edible mushrooms, collected from three different sites (urban, traffic and pastureland areas) in Lugo (NW Spain). The hymenophore (H) and the rest of the fruiting body (RFB) were analysed separately. The analyses were performed using inductively coupled plasma optical emission spectrometry (ICP-OES). The highest mean chromium levels (mg/kg dry weight) of 3.5 and 8.0, 4.5 and 6.2, and 6.2 and 4.3 were found in Lycoperdon utriforme, Coprinus comatus and Agaricus campestris in H and RFB, respectively. The highest concentrations of chromium were observed in terrestrial saprophytic species in relation to mycorrhizal species. With respect to the underlying substrates, chromium concentration was lowest in the pastureland area (24.6 mg/kg dw). All mushroom species were bioexclusors of chromium (BCFmushrooms harvested from the areas investigated poses no toxicological risk to human health due to chromium.

  4. Innovative soil treatment process design for removal of trivalent chromium

    Energy Technology Data Exchange (ETDEWEB)

    Stallings, J.H. [Air Force, Wright-Patterson AFB, OH (United States). Aeronautical Systems Center; Durkin, M.E. [Hughes Missile Systems Co., Tucson, AZ (United States)

    1997-12-31

    A soil treatment process has been developed as part of a US Air Force environmental compliance project at Air Force Plant 44, Tucson, AZ for treating soil contaminated with heavy metals including trivalent chromium, cadmium, copper, and nickel. The process was designed to treat a total of 133,000 tons of soil in a 400 ton per day facility. Features of the soil treatment process include physical treatment and separation, and a chemical treatment process of the remaining fines using a hypochlorite leach allowing chromium to be solubilized at a high pH. After treating, fines are washed in three stage countercurrent thickeners and chromium hydroxide cake is recovered as a final produce from the leach solution. Treatability studies were conducted, laboratory and a pilot plant was built. Process design criteria and flow sheet, material balances, as well as preliminary equipment selection and sizing for the facility have been completed. Facility was designed for the removal of Cr at a concentration of an average of 1230 mg/kg from the soil and meeting a risk based clean-closure limit of 400 mg/kg of Cr. Capital costs for the 400 tpd plant were estimated at 9.6 million with an operating and maintenance cost of $54 per ton As process is most economic for large quantities of soil with relatively low concentrations of contaminants, it was not used in final closure when the estimated volume of contaminated soil removed dropped to 65,000 tons and concentration of chromium increased up to 4000 mg/kg. However, the process could have application in situations where economics and location warrant.

  5. Chromium speciation in solid matrices and regulation: a review

    Energy Technology Data Exchange (ETDEWEB)

    Unceta, N. [University of the Basque Country, Department of Analytical Chemistry, Faculty of Pharmacy, Vitoria-Gasteiz (Spain); Seby, F. [Ultra Traces Analyses Aquitaine (UT2A), Helioparc Pau-Pyrenees, Pau (France); Malherbe, J.; Donard, O.F.X. [Universite de Pau et des Pays de l' Adour, Helioparc Pau-Pyrenees, Laboratoire de Chimie Analytique Bio-Inorganique et Environnement, IPREM, UMR CNRS 5254, Pau (France)

    2010-06-15

    In recent years, the extensive use of chromium in industrial processes has led to the promotion of several directives and recommendations by the European Union, that try to limit and regulate the presence of Cr(VI) in the environment and to protect industrial workers using chromium and end-users of manufactured products. As a consequence, new standard methods and analytical procedures have been published at the EU level for Cr(VI) determination in soil, sludge, sediment, and similar waste materials, workplace atmospheres, cement, packaging materials, industrially produced samples, and corrosion-protection layers on some components of vehicles and electrical and electronic equipment. The objective of this article is to summarize the different directives and recommendations and to critically review the currently existing standard methods and the methods published in the literature for chromium speciation in the above mentioned solid matrices, putting the emphasis on the different extraction procedures which have been developed for each matrix. Particular attention has been paid to Cr(III) and Cr(VI) inter-conversions that can occur during extraction and efforts to minimize these unwanted reactions. Although the use of NaOH-Na{sub 2}CO{sub 3} solutions with hot plate extraction seems to be the more widespread procedure, species transformation can still occur and several studies suggest that speciated isotope-dilution mass spectrometry (SIDMS) could be a suitable tool for correction of these interconversions. Besides, recent studies have proved the role of Cr(III) in chromium toxicology. As a consequence, the authors suggest an update of standard methods in the near future. (orig.)

  6. Technology Demonstration of the Zero Emissions Chromium Electroplating System

    Science.gov (United States)

    2008-02-01

    blanket technology for electroplating tanks. When no liquid blanket is used, evaporation of water, especially during warm weather conditions, requires...0.007 0.004 0.002 Tank 12A had noticeable blobs floating on the surface and also at the interfacial layer of PRD fluid and the chromium acid solution...Tank 12B did not have any such blobs . All the parts removed after plating looked fairly good. There were no visible streaks, water breaks, etc. The

  7. THE WEAR RESISTANCE INCREASE OF CHROMIUM CAST IRON

    Directory of Open Access Journals (Sweden)

    V. M. Ilyushenko

    2016-01-01

    Full Text Available The article presents the results of the tests on the wear resistance of chromium cast irons of different compositions obtained in sand forms. It has been shown that increase of the wear resistance and mechanical properties of the cast iron is possible to obtain using the casting in metal molds. A further increase in wear resistance of parts produced in metal molds is possible by changing the technological parameters of casting and alloying by titanium.

  8. Evidence of weak ferromagnetism in chromium(III) oxide particles

    Energy Technology Data Exchange (ETDEWEB)

    Vazquez-Vazquez, Carlos E-mail: qfmatcvv@usc.es; Banobre-Lopez, Manuel; Lopez-Quintela, M.A.; Hueso, L.E.; Rivas, J

    2004-05-01

    The low temperature (4chromium(III) oxide particles have been studied. A clear evidence of the presence of weak ferromagnetism is observed below 250 K. The magnetisation curves as a function of the applied field show coercive fields due to the canted antiferromagnetism of the particles. Around 55 K a maximum is observed in the zero-field-cooled curves; this maximum can be assumed as a blocking temperature, similarly to ultrafine ferromagnetic particles.

  9. Chromium related degradation of solid oxide fuel cells; Chrom-bezogene Degradation von Festoxid-Brennstoffzellen

    Energy Technology Data Exchange (ETDEWEB)

    Neumann, Anita

    2011-05-04

    Solid Oxide Fuel Cells (SOFCs) offer a high potential for application as an auxiliary power unit (APU) for heavy goods vehicles as well as combined heat and power (CHP) systems. SOFCs are especially attractive due to their high efficiencies and the use of different fuel types. However, optimization in terms of long term stability and costs are still necessary. This work characterized the degradation of SOFCs with lanthanum strontium manganite (LSM) cathodes under chromium influence. Galvanostatic cell tests were carried out at 800 C with operation times from 250 - 3000 h and variation of the chromium source and current density. The current densities of j = 0 (A)/(cm{sup 2}), j = 0,3 (A)/(cm{sup 2}) and j = 0,5 (A)/(cm{sup 2}) were applied. The high temperature ferritic alloy Crofer22APU was used as a chromium source. Variation of the chromium source was realized by coating the Crofer22APU insert with the chromium retention layer Mn{sub 3}O{sub 4} and the cathode contact layer LCC10. Cell degradation was analyzed with regard to cell voltage, current density and area specific resistance (ASR). Microstructural alterations of the cathode as well as chromium content and distribution across the cell were investigated after completion of the cell tests. For cells with a chromium source present and operation with a nonzero current density, the course of cell degradation was divided into three phases: a run-in, weak linear degradation and strong linear degradation. A decrease of the chromium release rate by means of different coatings stretched the course of degradation along the timescale. Strong degradation, which is characterized by a significant increase in ASR as well as a decrease of current density at the operating point, was only observed when a chromium source in the setup was comb ined with operation of the cell with a non-zero current density. Operation of the cell with a chromium source but no current density caused a degradation of current density at the

  10. Adsorptive stripping voltammetric determination of chromium in gallium.

    Science.gov (United States)

    Palrecha, M M; Mathur, P K

    1997-12-19

    The electroanalytical chemistry of trace metals has progressed strongly with the development of cathodic stripping voltammetry (CSV) preceded by adsorption collection of organic metal complexes. A sensitive method for the determination of trace amount of chromium in gallium is described. Gallium is dissolved in sodium hydroxide containing hydrogen peroxide. The method is based on the catalytic activity of nitrate ions on the reduction of Cr(III)TTHA (triethylene tetramine-N,N,N',N'',N''',N'''-hexaacetic acid) complex. The sensitivity of this method is further improved by adsorption preconcentration of Cr(III)TTHA complex at a hanging mercury drop electrode (HMDE). The Cr(III) formed at the electrode surface by the reduction of Cr(VI), which is present in the bulk solution, is immediately complexed by TTHA. The adsorbed complex is then reduced at a peak potential of - 1.26 V, and the peak height of Cr(III) reduction is measured. The determination limit was restricted by the amount of chromium present in the reagent blank solution. The method is suitable for the determination of chromium at level as low as 0.2 mug g(-1) (with about 50 mg of sample) and a relative standard deviation of 15%.

  11. The chromium site in doped glassy lithium tetraborate

    Energy Technology Data Exchange (ETDEWEB)

    Kelly, T.D. [Department of Engineering Physics, Air Force Institute of Technology, 2950 Hobson Way, Wright Patterson Air Force Base, OH 45433 (United States); Echeverria, E.; Beniwal, Sumit [Department of Physics and Astronomy, 855 North 16th Street, Theodore Jorgensen Hall, University of Nebraska-Lincoln, Lincoln, NE 68588-0299 (United States); Adamiv, V.T.; Burak, Ya. V.; Enders, Axel [Institute of Physical Optics, 23 Dragomanov Street, Lviv 79005 (Ukraine); Petrosky, J.C.; McClory, J.W. [Department of Engineering Physics, Air Force Institute of Technology, 2950 Hobson Way, Wright Patterson Air Force Base, OH 45433 (United States); Dowben, P.A., E-mail: pdowben1@unl.edu [Department of Physics and Astronomy, 855 North 16th Street, Theodore Jorgensen Hall, University of Nebraska-Lincoln, Lincoln, NE 68588-0299 (United States)

    2014-10-15

    Using extended X-ray absorption fine structure (EXAFS) spectroscopy, we find that Cr substitutes primarily in the Li{sup +} site as a dopant in lithium tetraborate Li{sub 2}B{sub 4}O{sub 7} glasses, in this case 98.4Li{sub 2}B{sub 4}O{sub 7}–1.6Cr{sub 2}O{sub 3} or nominally Li{sub 1.98}Cr{sub 0.025}B{sub 4}O{sub 7}. This strong preference for a single site is nonetheless accompanied by site distortions and some site disorder, helping explain the optical properties of chromium doped Li{sub 2}B{sub 4}O{sub 7} glasses. The resulting O coordination shell has a contraction of the Cr–O bond lengths as compared to the Li–O bond lengths. There is also an increase in the O coordination number. - Graphical abstract: Lithium tetraborate: labeled are the B1 and B2 sites, where the latter correspond to BO{sub 3} and BO{sub 4} structures respectively. - Highlights: • Adoption of the Li + site for chromium dopants in lithium tetraborate identified. • Increased oxygen coordination for glass over the crystalline lithium tetraborate. • Distortions about the doping chromium characterized. • Local bond order is preserved in spite of the glassy nature.

  12. Chromium and manganese interactions in streptozocin-diabetic rats

    Energy Technology Data Exchange (ETDEWEB)

    Davis, M.L.; Jarrett, C.R.; Adeleye, B.O.; Stoecker, B.J. (Oklahoma State Univ., Stillwater (United States))

    1991-03-15

    Weanling male rats were fed casein-based diets low in chromium and manganese ({minus}Cr-MN) or supplemented with 1 ppm chromium as chromium chloride (+Cr) and/or 55 ppm manganese as manganous carbonate in a factorial design. After 7 weeks on the experimental diets, half of the rats in each group were injected on 2 consecutive days with 55 mg/kg streptozocin (STZ) in citrate buffer pH 4. Four weeks after injection, serum glucose in the diabetic group supplement with both Cr and Mn was not different from non-diabetic animals; however, diabetic animals in {minus}Cr groups or in the +Cr-Mn group had significantly elevated serum glucose. Serum insulin was reduced by STZ. A significant interaction between Mn and diabetes affected serum cortisol concentrations. More new tissue was formed on a polyvinyl sponge inserted under the skin in +Mn animals. In this study, the STZ animals were more sensitive than the control animals to dietary Cr and Mn concentrations.

  13. Magnesium, zinc, and chromium nutriture and physical activity.

    Science.gov (United States)

    Lukaski, H C

    2000-08-01

    Magnesium, zinc, and chromium are mineral elements required in modest amounts to maintain health and optimal physiologic function. For physically active persons, adequate amounts of these micronutrients are needed in the diet to ensure the capacity for increased energy expenditure and work performance. Most physically active individuals consume diets that provide amounts of magnesium and zinc sufficient to meet population standards. Women tend to consume less of these minerals than is recommended, in part because they eat less food than men. Inadequate intakes of magnesium and zinc have been reported for participants in activities requiring restriction of body weight. Dietary chromium is difficult to estimate because of a lack of appropriate reference databases. Acute, intense activity results in short-term increases in both urine and sweat losses of minerals that apparently diminish during recovery in the days after exercise. Supplemental magnesium and zinc apparently improve strength and muscle metabolism. However, evidence is lacking as to whether these observations relate to impaired nutritional status or a pharmacologic effect. Chromium supplementation of young men and women does not promote muscle accretion, fat loss, or gains in strength. Physically active individuals with concerns about meeting guidelines for nutrient intake should be counseled to select and consume foods with high nutrient densities rather than to rely on nutritional supplements. The indiscriminate use of mineral supplements can adversely affect physiologic function and impair health.

  14. Fabrication of chitosan-magnetite nanocomposite strip for chromium removal

    Science.gov (United States)

    Sureshkumar, Vaishnavi; Kiruba Daniel, S. C. G.; Ruckmani, K.; Sivakumar, M.

    2016-02-01

    Environmental pollution caused by heavy metals is a serious threat. In the present work, removal of chromium was carried out using chitosan-magnetite nanocomposite strip. Magnetite nanoparticles (Fe3O4) were synthesized using chemical co-precipitation method at 80 °C. The nanoparticles were characterized using UV-visible spectroscopy, fourier transform infrared spectroscopy, X-ray diffraction spectrometer, atomic force microscope, dynamic light scattering and vibrating sample magnetometer, which confirm the size, shape, crystalline nature and magnetic behaviour of nanoparticles. Atomic force microscope revealed that the particle size was 15-30 nm and spherical in shape. The magnetite nanoparticles were mixed with chitosan solution to form hybrid nanocomposite. Chitosan strip was casted with and without nanoparticle. The affinity of hybrid nanocomposite for chromium was studied using K2Cr2O7 (potassium dichromate) solution as the heavy metal solution containing Cr(VI) ions. Adsorption tests were carried out using chitosan strip and hybrid nanocomposite strip at different time intervals. Amount of chromium adsorbed by chitosan strip and chitosan-magnetite nanocomposite strip from aqueous solution was evaluated using UV-visible spectroscopy. The results confirm that the heavy metal removal efficiency of chitosan-magnetite nanocomposite strip is 92.33 %, which is higher when compared to chitosan strip, which is 29.39 %.

  15. Foam separation of chromium (Ⅵ) from aqueous solution

    Institute of Scientific and Technical Information of China (English)

    JIAO Cai-shan; DING Yan

    2009-01-01

    Removal of chromium (Ⅵ) dissolved in water by intermittent foam separation was implemented with cetyl trimethy-ammonium bromide as surfactant. The influence of various factors on removal efficiency was systematically studied. The removal efficiency has a maximum value near pH 4.0; thus, most experiments were carried out at pH 4.0. The orthogonal experiment was conducted to confirm the optimal operating parameters. The orthogonal experimental results show that when the liquid feed concentration is 10 mg/L, the pH value of feed solution is 4.00, air flow rates 0.9 L/min, surfactant dosage is 300 mg/L, the maximum removal efficiency of chromium (Ⅵ) reaches 97.80%, and condense multiple reaches 1711. The kinetic test indicates that the foam separation of chromium is a first-order process. The equivalent rate constant calculated from the slope is 0.406 4, and the equivalent rate equation is obtained.

  16. Fabrication of Carbon Nanotube - Chromium Carbide Composite Through Laser Sintering

    Science.gov (United States)

    Liu, Ze; Gao, Yibo; Liang, Fei; Wu, Benxin; Gou, Jihua; Detrois, Martin; Tin, Sammy; Yin, Ming; Nash, Philip; Tang, Xiaoduan; Wang, Xinwei

    2016-03-01

    Ceramics often have high hardness and strength, and good wear and corrosion resistance, and hence have many important applications, which, however, are often limited by their poor fracture toughness. Carbon nanotubes (CNTs) may enhance ceramic fracture toughness, but hot pressing (which is one typical approach of fabricating CNT-ceramic composites) is difficult to apply for applications that require localized heat input, such as fabricating composites as surface coatings. Laser beam may realize localized material sintering with little thermal effect on the surrounding regions. However, for the typical ceramics for hard coating applications (as listed in Ref.[1]), previous work on laser sintering of CNT-ceramic composites with mechanical property characterizations has been very limited. In this paper, research work has been reported on the fabrication and characterization of CNT-ceramic composites through laser sintering of mixtures of CNTs and chromium carbide powders. Under the studied conditions, it has been found that laser-sintered composites have a much higher hardness than that for plasma-sprayed composites reported in the literature. It has also been found that the composites obtained by laser sintering of CNTs and chromium carbide powder mixtures have a fracture toughness that is ~23 % higher than the material obtained by laser sintering of chromium carbide powders without CNTs.

  17. Simultaneously Recovering High-Purity Chromium and Removing Organic Pollutants from Tannery Effluent

    OpenAIRE

    Jie Zong; Yan-Chun Li; Kang Hu

    2016-01-01

    Chromium pollution is a serious issue because of carcinogenic toxicities of the pollutants and low recovery rate of chromium because of the presence of organic, such as protein and fat. In this work, high recovery rate and high purity of the chromium ion were successfully prepared by the way of acid enzyme, flocculant, and Fenton oxidation. The experiments were characterized by TG, TOC, UV-VIS, and SEM. In the work, the tannery waste chrome liquor was used as experimental material. The result...

  18. Adsorption of Chromium(VI) from Aqueous Solutions by Coffee Polyphenol-Formaldehyde/Acetaldehyde Resins

    OpenAIRE

    2013-01-01

    Removal of chromium(VI) from wastewater is essential as it is toxic. Thus, removal of chromium(VI) was performed using coffee polyphenol-formaldehyde/acetaldehyde resins as adsorbents. Adsorbent resins were prepared by condensation of decaffeinated coffee powder with formaldehyde/acetaldehyde and used for the removal of Cr(VI) ions from aqueous solutions. A simple and sensitive solid phase extraction procedure was applied for the determination of chromium at trace levels by spectroscopic meth...

  19. Chromium(III, VI) speciation analysis with preconcentration on a maleic acid-functionalized XAD sorbent

    Energy Technology Data Exchange (ETDEWEB)

    Yalcin, Sibel; Apak, Resat

    2004-03-03

    Chromium may exist in environmental waters as Cr(III) and Cr(IV), the latter being the toxic and carcinogenic form. Since atomic absorption spectrometry (AAS) and inductively coupled plasma atomic emission spectrometry can only yield information on total Cr concentration, a polymer resin bearing O,O-donor chelating groups such as the maleic acid-functionalized XAD-(CO)CH-CH-COOH resin was synthesized to selectively retain Cr(III) at pH 4.0-5.5. The dynamic breakthrough capacity of the resin for Cr(III) at pH 5.0 was 7.52 mg g{sup -1}, and the preconcentration factor extended to 250-300. Chromium(III) in the presence of 250-fold Cr(VI)--which was not retained--could be effectively preconcentrated on the NH{sub 4}{sup +}-form of the resin and determined by AAS or diphenylcarbazide (DPC) spectrophotometry. When Cr(VI) was reduced to Cr(III) with Na{sub 2}SO{sub 3} solution brought to pH 1 by the addition of 1 M H{sub 2}SO{sub 4}, and preconcentrated on the resin, total Cr could be determined. The developed method was validated with a blended coal sample CRM-1632. Since the adsorption behavior as a function of pH of possible interferent metal ions, e.g. Ni(II), Co(II), Cu(II), Cd(II), Zn(II), Pb(II) and Fe(III), was similar to that of Cr(III), selective elution of Cr(III) from the resin was realized using a mixture of 1 wt.% H{sub 2}O{sub 2}+1 M NH{sub 3}. The eluate containing Cr as chromate could be directly analyzed by diphenyl carbazide spectrophotometry without any adverse effect from the common interferents of this method, i.e. Fe(III), Cu(II) Hg(II), VO{sub 3}{sup -}, MoO{sub 4}{sup 2-} and WO{sub 4}{sup 2-}. Various synthetic waste solutions typical of electroplating bath effluents containing Cr, Cu, Ni, Zn, Na, Ca, cyanide (and chemical oxidation demand (COD), achieved by glucose addition) were subjected to pretreatment procedures such as hypochlorite oxidation (of cyanide) and catalytic oxidation (of COD) with peroxodisulfate. Chromium determination gave

  20. Antiferromagnetism in chromium alloy single crystals

    DEFF Research Database (Denmark)

    Bjerrum Møller, Hans; Trego, A.L.; Mackintosh, A.R.

    1965-01-01

    The antiferromagnetism of single crystals of dilute alloys of V, Mn and Re in Cr has been studied at 95°K and 300°K by neutron diffraction. The addition of V causes the diffraction peaks to decrease in intensity and move away from (100), while Mn and Re cause them to increase and approach (100) so...

  1. USE OF TWO DIGESTION METHODS IN THE EVALUATION OF CHROMIUM CONTENT IN CATTLE'S MEAT SUPPLEMENTED WITH CHROMIUM CHELATES

    Directory of Open Access Journals (Sweden)

    R. L. T. de Andrade

    2015-06-01

    Full Text Available The present study aimed to analyze the chromium content in beef using two digestion methods. There were used samples from 24 18-month-old male cattle, and twelve of them were supplemented and twelve were not supplemented with chromium chelate. These samples were evaluated by atomic absorption spectroscopy, previously submitted to digestion method using nitric acid (65% with hydrogen peroxide (35% and to digestion method, using solution of nitric perchloric acid in the proportion 3:1. Immediately after the slaughter, the carcasses were sent to sanitary maturation. After 24 hours, samples between 12th and 13th rib in the muscle Longissimus Thoracis were taken. For evaluation, it was used completely randomized design (Die and analysis of variance (ANOVA at 5% of significance level. The results didn't evidenced any significant difference (p>0,05 between the (cromo content, regardless the supplementation. The same happened with the digestion methods used.

  2. Assessment of Hexavalent Chromium Natural Attenuation for the Hanford Site 100 Area

    Energy Technology Data Exchange (ETDEWEB)

    Truex, Michael J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Szecsody, James E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Qafoku, Nikolla P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Sahajpal, Rahul [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Zhong, Lirong [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lawter, Amanda R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lee, Brady D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2015-09-01

    Hexavalent chromium (Cr(VI)) plumes are present in the 100 Area at the Hanford Site. Remediation efforts are under way with objectives of restoring the groundwater to meet the drinking-water standard (48 µg/L) and protecting the Columbia River by ensuring that discharge of groundwater to the river is below the surface-water quality standard (10 µg/L). Current remedies include application of Pump-and-Treat (P&T) at the 100-D, 100-H, and 100-K Areas and Monitored Natural Attenuation (MNA) at the 100-F/IU Area. Remedy selection is still under way at the other 100 Areas. Additional information about the natural attenuation processes for Cr(VI) is important in all of these cases. In this study, laboratory experiments were conducted to demonstrate and quantify natural attenuation mechanisms using 100 Area sediments and groundwater conditions.

  3. Biosorption and removal of chromium from water by using moringa seed cake (Moringa oleifera Lam.

    Directory of Open Access Journals (Sweden)

    Ana Paula Meneghel

    2013-01-01

    Full Text Available This study evaluated the adsorption capacity of chromium from contaminated aqueous solutions by using Moringa oleifera Lam. seeds. Parameters such as solution pH, adsorbent mass, contact time between solution and adsorbent, isotherms, thermodynamic, kinetics, and desorption were evaluated. The maximum adsorption capacity (Qm calculated to be 3.191 mg g-1 for the biosorbent. Activated carbon was used for comparison purposes in addition to the biosorbent. The best fit was obtained by the Langmuir model for both adsorbents. The average desorption value indicated that both the biosorbent and activated carbon have a strong interaction with the metal. The results showed that the biosorbent has advantages owing to its low cost and efficiency in Cr3+ removal from contaminated waters.

  4. Chromium and copper influence on the nodular cast iron with carbides microstructure

    Directory of Open Access Journals (Sweden)

    G. Gumienny

    2010-10-01

    Full Text Available In this paper chromium to 1,00% and copper to 1,50% influence at constant molybdenum content of about 1,50% on the nodular cast ironwith carbides microstructure has been presented. It was found, that as a result of synergic addition of above-mentioned elements there isthe possibility obtaining an ausferrite in nodular cast iron with carbides castings. Conditions have been given, when in nodular cast iron with carbides at cooling at first in the form, then air-cooling austenite transformation to upper bainite, its mixture with lower bainite, martensite or ausferrite takes place. Transformations proceed during cooling and the crystallization of cast iron have been determined and the casting hardness has been presented.

  5. Corrosion of High Chromium Ferritic/Martensitic Steels in High Temperature Water. a Literature Review

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez, P.; Lapena, J.; Blazquez, F. [Ciemat, Madrid (Spain)

    2000-07-01

    Available literature concerning corrosion of high-chromium ferritic/martensitic steels in high temperature water has been reviewed. The subjects considered are general corrosion, effect of irradiation on corrosion, stress corrosion cracking (SCC) and irradiation-assisted stress corrosion cracking (IASCC). In addition some investigations about radiation induced segregation (RIS) are shown in order to know the compositional changes at grain boundaries of these alloys and their influence on corrosion properties. The data on general corrosion indicate moderate corrosion rates in high temperature water up to 350 degree centigree. Considerably larger corrosion rates were observed under neutron irradiation. The works concerning to the behaviour of these alloys to stress corrosion cracking seem to conclude that in these materials is necessary to optimize the temper temperature and to carry out the post-weld heat treatments properly in order to avoid stress corrosion cracking. (Author) 40 refs.

  6. Influence of promoters and oxidants on propane dehydrogenation over chromium-oxide catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Lapidus, A.L.; Agafonov, Yu.A.; Shaporeva, N.Yu.; Trushin, D.V.; Gaidai, N.A.; Nekrasov, N.V. [Russian Academy of Sciences, Moscow (Russian Federation). N.D. Zelinsky Inst. of Organic Chemistry

    2010-12-30

    Possibilities for increasing the efficiency of supported on SiO{sub 2} chromium-oxide catalysts in propane oxidative dehydrogenation in CO{sub 2} presence are investigated: the introduction of Li, Na, K, Ca in catalysts and the addition of O{sub 2} in the reaction mixture. It was been found that the positive role of K - the increase of the selectivity to propene and stability of catalysts at long-duration tests - appeared at the relation of Cr:K=20. It was shown that the presence of little amount of O{sub 2} (2%) in the reaction mixtures of propane and carbon dioxide resulted in the increase of propene yield and catalyst stability. (orig.)

  7. Microstructure and wear resistance of high chromium cast iron containing niobium

    Directory of Open Access Journals (Sweden)

    Zhang Zhiguo

    2014-05-01

    Full Text Available In the paper, the effect of niobium addition on the microstructure, mechanical properties and wear resistance of high chromium cast iron has been studied. The results show that the microstructure of the heat-treated alloys is composed of M7C3 and M23C6 types primary carbide, eutectic carbide, secondary carbide and a matrix of martensite and retained austenite. NbC particles appear both inside and on the edge of the primary carbides. The hardness of the studied alloys maintains around 66 HRC, not significantly affected by the Nb content within the selected range of 0.48%-0.74%. The impact toughness of the alloys increases with increasing niobium content. The wear resistance of the specimens presents little variation in spite of the increase of Nb content under a light load of 40 N. However, when heavier loads of 70 and 100 N are applied, the wear resistance increases with increasing Nb content.

  8. Advantages and Disadvantages of Chromium Salt%铬盐功过论(续)

    Institute of Scientific and Technical Information of China (English)

    王全杰

    2012-01-01

    对铬及其对人类的利害关系进行了详细的论述,包括铬与人体健康,铬在畜禽业中的应用,富铬农副产品的应用,铬鞣剂的不可取代性等。%Chromium as well as its advantages and disadvantages were introduced in detail,including chromium and human health,application in Livestock and Poultry Industry,Rich chromium agricultural and sideline products,Irreplaceable performance of chromium tanning agent,etc.

  9. Advantages and Disadvantages of Chromium Salt%铬盐功过论

    Institute of Scientific and Technical Information of China (English)

    王全杰

    2012-01-01

    Chromium as well as its advantages and disadvantages were introduced in detail, including chromium and human health, application in Livestock and Poultry Industry, Rich chromium agricultural and sideline products, Irreplaceable performance of chromium tanning agent, etc.%对铬及其对人类的利害关系进行了详细的论述,包括铬与人体健康,铬在畜禽业中的应用,富铬农副产品的应用,铬鞣剂的不可取代性等。

  10. Determination of total chromium in tanned leather samples used in car industry.

    Science.gov (United States)

    Zeiner, Michaela; Rezić, Iva; Ujević, Darko; Steffan, Ilse

    2011-03-01

    Despite the high competition of synthetic fibers leather is nowadays still widely used for many applications. In order to ensure a sufficient stability of the skin matrix against many factors, such as microbial degradation, heat and sweat, a tanning process is indispensable. Using chromium (III) for this purpose offers a multitude of advantages, thus this way of tanning is widely applied. During the use of chromium tanned leather as clothing material as well as for decoration/covering purposes, chromium is extracted from the leather and may then cause nocuous effects to human skin, e.g. allergic reactions. Thus the knowledge of the total chromium content of leather samples expected to come into prolonged touch with human skin is very important. In car industry leather is used as cover for seats, steering wheel and gearshift lever The chromium contents often chromium tanned leather samples used in car industry were determined. First all samples were dried at 65 degrees C overnight and then cut in small pieces using a ceramic knife, weighed and analyzed by inductively coupled plasma--optical emission spectrometry (ICP-OES) after acidic microwave assisted digestion. The total chromium amounts found were in the range from 19 mg/g up to 32 mg/g. The extraction yield of chromium from leather samples in sweat is approximately 2-7%. Thus especially during long journeys in summer chromium can be extracted in amounts which may cause nocuous effects for example on the palm of the hands or on the back.

  11. Chromium status and glucose tolerance in Saudi men with and without coronary artery disease.

    Science.gov (United States)

    Alissa, Eman M; Bahjri, Suhad M; Ahmed, Waqar H; Al-Ama, Nabeel; Ferns, Gordon A A

    2009-12-01

    Chromium deficiency is associated with impaired glucose tolerance (IGT) and dyslipidemia. Hence, the objective of the current study was to investigate chromium status among Saudi men with and without established cardiovascular disease (CVD) and its relationship to glucose tolerance, lipid profile and other established CVD risk factors. We measured serum and urine chromium concentrations, fasted lipid profile, plasma glucose, and serum lipid peroxide in 130 Saudi men with an established history of myocardial infarction and 130 age-matched controls without established CVD. Patients with established CVD had higher serum triglycerides (p < 0.05) and plasma glucose (p < 0.0001) and lower serum and urinary chromium concentrations (p < 0.0001) than controls. Serum chromium was inversely correlated with plasma glucose among cases and controls (r = -0.189, p < 0.05 and r = -0.354, p < 0.00001, respectively). Plasma glucose (OR 1.127, CI 1.0-1.269, p < 0.05), serum chromium (OR 0.99, CI 0.985-0.995, p < 0.0001), and urinary chromium (OR 0.988, CI 0.981-0.995, p < 0.001) were independently associated with the presence of established coronary disease applying this model. While chromium metabolism appears to be altered in individuals with CVD, it is unclear whether chromium supplementation would be effective in CVD prevention among patients with IGT. This would need to be tested in long-term outcome trials.

  12. The risk implications of the distribution of chromium forms in environmental media

    Energy Technology Data Exchange (ETDEWEB)

    Mahoney, L.A.; Petroff, D.M.; Batey, J.C. [Eckenfelder Inc., Nashville, TN (United States)

    1996-12-31

    Chromium exhibits multiple oxidation (valence) states, ranging from ({minus}2) to (+6). Under natural conditions, however, chromium typically exists in the Cr(III) (trivalent) and/or Cr(VI) (hexavalent) form, with the hexavalent form exhibiting higher solubility and much greater toxicity than the trivalent form. Due to the large differences in toxicity, the distribution of chromium oxidation states (Cr(III) and Cr(VI)) in site media is potentially of great importance to the calculation of site risk levels, and thus ultimately to cleanup activities. Despite its importance, chromium oxidation states are often not available for media samples collected at waste sites. Typical assumptions regarding the chromium distribution in site media are presented. Actual chromium distribution data from media from baseline investigations of several waste sites are also presented for groundwater, surface water, and soil and compared in terms of background chromium levels and the nature of site wastes. The differences in toxicity of Cr(III) and Cr(VI) are briefly discussed. Risk estimates and risk-based cleanup levels generated using different assumptions for the distribution of chromium in site media for a selected example site are then given. These risk-based cleanup levels are compared to various state regulatory limits, MCLs, and Practical Quantitation Limits (PQLs) for chromium.

  13. The prevalence of chromium allergy in Denmark is currently increasing as a result of leather exposure

    DEFF Research Database (Denmark)

    Thyssen, J P; Jensen, P; Carlsen, B C;

    2009-01-01

    previously been demonstrated among Danish construction workers. OBJECTIVES: To investigate the development of chromium allergy among patients with dermatitis tested between 1985 and 2007 in Denmark. Furthermore, to determine causative exposures in patients with chromium allergy. PATIENTS AND METHODS......: A retrospective analysis of patch test data was performed (n = 16,228) and charts from patients with chromium allergy were reviewed. Comparisons were made using a chi(2) test. Logistic regression analyses were used to test for associations. RESULTS: The prevalence of chromium allergy decreased significantly from...

  14. Chromium Isotopes in Marine Carbonates - an Indicator for Climatic Change?

    Science.gov (United States)

    Frei, R.; Gaucher, C.

    2010-12-01

    Chromium (Cr) stable isotopes experience an increased interest as a tracer of Cr (VI) reduction in groundwater and thus showed their potential as a monitor of remediation of anthropogenic and natural contamination in water (Berna et al., 2009; Izbicki et al., 2008). Chromium stable isotopes in Fe-rich chemical sediments (BIFs and Fe-cherts) have recently also been used as a tracer for Earth's atmospheric oxygenation through time (Frei et al., 2009). We have applied the Cr isotope system to organic-rich carbonates from a late Ediacaran succession in Uruguay (Polanco Formation), from which we have previously analyzed BIFs with extremely fractionated (δ53Cr up to 5.0 ‰) Cr isotope signatures that are part of an underlying deep water clastic sediment (shale-dominated) sequence (Yerbal Formation) deposited in a glacio-marine environment (Gaucher et al.,2004). δ53Cr values of organic rich carbonates correlate with positive and negative carbon isotope excursions (δ13C PDB between -3 and +3 ‰) and with systematic changes in strontium isotope compositions, commonly interpreted as to reflect fluctuations in organic (photosynthetic algae) production related to fluctuations in atmospheric oxygen and weathering intensities, respectively. Slightly positively fractioned δ53Cr values (up to +0.25‰), paralleling positive (δ13C PDB and 87Sr/86Sr ratio excursions would thereby trace elevated atmospheric oxygen levels/pulses possibly related to glacier retreat/melting stages that caused bioproductivity to increase. While the causal link between these multiple isotopic tracers and the mechanisms of Cr stripping into carbonates has to be further investigated in detail, the first indications from this study point to a potentially promising use of stable Cr isotopes in organic-rich carbonates to monitor fluctuations of atmospheric oxygen, particularly over the Neoproterozoic and Phanerozoic ice age periods. E.C. Berna et al. (2010) Cr stable isotopes as indicators of Cr

  15. Analysis of the bioavailability of Cr(III and Cr(VI based on the determination of chromium in Mentha piperita by graphite furnace atomic absorption spectrometry

    Directory of Open Access Journals (Sweden)

    SVETLANA ĐOGO

    2011-01-01

    Full Text Available Mentha piperita L. (Lamiaceae was cultivated under the controlled laboratory conditions in the presence of varying levels of trivalent and hexavalent chromium in order to determine its capacity to control chromium uptake and its tolerance limit. The plants were grown in pots at 25 °C with controlled soil moisture (about 80 % of the water retention capacity. The soil was treated with increasing concentrations of Cr(NO33 (40, 80, 120, and 200 mg kg-1 and K2Cr2O7 (2.5, 5, 10, and 15 mg kg-1. A control group of plants was grown without the addition of chromium to the soil. For each concentration, three acidity levels were tested: natural, one pH unit below and one above the natural acidity of the soil (pH2 6, pH1 5 and pH3 7. The plant samples were digested according to the standard procedure and chromium content was determined by GFAAS. For all plants, the transportation index was calculated and the results (expressed in mg kg-1 at pH1, pH2 and pH3, respectively, were: 0.21–0.80, 0.06–1.06 and 0.04–0.52. The recoveries were good (72.73–115.3 % as evidenced by the analysis of certified reference materials (NIST SRM 8433 – Corn Bran and NIST SRM 1547 – Peach Leaves. The mobility of chromium through the plants tissues is discussed in regard to its competition with iron and manganese for transport binding sites; hence Mn and Fe were also determined.

  16. Problems of phase identification in high-nitrogen chromium-manganese cast steel

    Directory of Open Access Journals (Sweden)

    Z. Pirowski

    2008-03-01

    Full Text Available An atzcrnpt has been madc to offcr an intcrprctation of ihc rnicrostructurc of chromium-mangancx cast stccl aftcr adding to 1his stccla targc amount of nitrogcn as an alloying clcrncnr. Nitropcn was addcd 10 rhc cast stccl by two mcthods: rhc first mcthod consistcrl inadding a nitridcd fcrrornangancsc, the second method in rcmclting thc nitrogen-rscc alloy undcr rhc atrnosphcrc of nitrogen maintaininghigh N1 prcssurc abovc the mctal meSt (33 MPa.Somc imponant diffcrcnces in the microstructurc of rhc cxamincd cast sleet havc bccn observed. dcpcnding on how the nitrogcn wasintroduced to Ihc alloy. Whcn melting was carried out undcr thc armosphcric prcssurc adding thc nitridcd fcrroaIloys. the matrix was composedof nitridcd nustcnitc, and numerous nitrides (carboni~rides wcrc forming a wcll-dcvclopcd ncrwork along tbc grain boundaries.Mcl t ing of alloy iindcr thc high prcsairc or nirrogcn enabPcs oblaining much highcr concentrarion of this clclncnt in lncral. Thc network ofprccipilarcs along lhc grain houndwics is obscrvcd to cxist no longcr. and thc Pamellar stmcturc occupics now practically ihc cnrirc mctalvolumc. Whcn :illoys arc mcltctt in rhc air, only small fragments oh the lamellar structurc, forming thc. so ca!lcd. "Chincse script" and localclusters arc! prcscnt.At this stagc of thc rcscarch. an artcmpa has bcen mad& to identify thc phascs in chromium-~nnngn~icsc cnst stccl u s i n ~a transmissionclectron rnicroscopc. Thc conducrcd slzldics pnnly confirrncd rhc conclusions resulting from ~ h ccx nminntions cnrricd out prcvioi~slyu ndcrthc optical rnicroscopc. So far. howcvcr, no consistcna answer has bccn found to thc qucstion of what typc arc Z ~ pCrc cipi~alcsp rcscnt inthe structurc of thc cxamincrh alloy.Attcmpts at furthcr intcrprcintion of thc obtained tcsults will hc taken at the next stage of thc work with n~tcntionfo ci~sscdo n thc prccipitatcsformed during rhc proccss of wlidilicat ion of thc cxnmincd chromium-manganese cast

  17. Iron-rich Oklahoma clays as a natural source of chromium in monitoring wells.

    Science.gov (United States)

    Scott, Dane; Apblett, Allen; Materer, Nicholas F

    2011-12-01

    Water samples, drawn from groundwater monitoring wells located southeast of Oklahoma City, OK, were found to contain elevated concentrations of total chromium with an apparent source localized to the area surrounding each well. Since these monitoring wells are located in areas with no historic chromium usage, industrial sources of chromium were ruled out. Water testing was performed on twelve monitoring wells in the area that historically had elevated total chromium concentrations ranging from 10-4900 micrograms per litre. Filtered water samples were found to be free of chromium contamination, indicating that the source of the chromium is the suspended solids. Analysis of these solids by acid digestion and a sequential extraction technique revealed that the chromium was primarily associated with iron-containing solids. X-ray diffraction identified goethite, an iron oxide hydroxide, as the dominant iron-containing phase in the suspended solids. The mineralogy in this region is dominated by interbedded red-bed sandstone and mudstone whose mineral content includes mixed-layer illite-smectite, hematite, goethite, gypsum and dolomite. Elemental analysis of soil samples collected as a function of depth in the locale of the monitoring wells indicated that the iron rich clays contain a natural source of chromium. The elevated levels of total chromium are most likely due to the dissolution of silica and alumina from the chromium containing iron clays in the basic well water, resulting in the release of fine suspended solids that naturally have high chromium concentrations. These results should be applicable to other areas containing iron-rich clays.

  18. Influence of rare earth nanoparticles and inoculants on performance and microstructure of high chromium cast iron

    Institute of Scientific and Technical Information of China (English)

    HOU Yuncheng; WANG You; PAN Zhaoyi; YU Lili

    2012-01-01

    The high chromium cast irons (HCCIs) with rare earth (RE) nanoparticles or inoculants were fabricated in the casting process.The phase compositions and microstructure were analyzed by X-ray diffraction (XRD) and optical microscopy (OM),respectively.The hardness and impact toughness were tested by Rockwel-hardmeter and impacting test enginery.And then,the morphology of fracture was researched by scanning electron microscopy (SEM).The results demonstrated that the phase compositions of HCCIs with addition of RE nanoparticles or inoculants which were M7C3 carbides + α -Fe did not change obviously.However,the prime M7C3 carbides morphology had great changes with the increase of RE nanoparticles,which changed from long lath to granular or island shape.When the content of RE nanoparticles was 0.4 wt.%,the microstructure of high chromium cast iron was refined greatly.The microstructure of carbides was coarser when the addition of RE nanoparticles was higher than 0.4 wt.%.The hardness and impact toughness of HCCIs were improved by addition of RE nanoparticles or inoculants.The impact toughness of HCCIs was increased 36.4% with RE nanoparticles of 0.4 wt.%,but the hardness changed slightly.In addition,the adding of RE nanoparticles or inoculants could reduce the degree of the brittle fracture.Fracture never seemed regular,instead,containing lots of laminates and dimples with the increase of the RE nanoparticles.The results also indicated that the optimal addition amonnt of the RE nanoparticles was 0.4%,under this composition,the microstructure and mechanical property achieved the best cooperation.In addition,through the study of erosion wear rate,when adding 0.4% RE nanoparticles into the HCCIs,the erosion wear rate got the minimum 0.32×10-3 g/mm2,which could increase 51.5% compared with that without any RE nanoparticles.

  19. Dehydrogenation of propane in the presence of CO{sub 2} over polyacid chromium oxide catalysts modified by Mo, W and Mn

    Energy Technology Data Exchange (ETDEWEB)

    Lapidus, A.L.; Agafonov, Yu.A.; Gaidai, N.A.; Nekrasov, N.V.; Davydov, P.E. [Russian Academy of Sciences, Moscow (Russian Federation). N.D. Zelinsky Institute of Organic Chemistry

    2013-11-01

    Effective chromium oxide catalysts without additions and with addition of Mo, W and Mn were prepared and tested in long-duration experiments for propane dehydrogenation in the presence of CO{sub 2}. The optimal concentrations of metals were found. It was shown that the best combination of acid-base and redox properties necessary for a decrease of aggregation of chromium-oxide particles was observed over the following catalyst: (3.0 wt.%Cr-1.5 wt.% Mn)/SiO{sub 2}. This catalyst worked stably in durable tests (500 h). Mechanism of propane oxidative dehydrogenation was studied using unstationary response method. It was shown that the process mechanism was similar over all studied catalysts but the catalysts were differed by the adsorption capacity of the reaction components: CO{sub 2} was tied more firmly than C{sub 3}H{sub 6} over Cr and Cr-Mn, C{sub 3}H{sub 6} was tied more strongly than CO{sub 2} over Cr-W. The reverse water-gas shift reaction proceeded in more extent over chromium-oxide catalysts without additions. (orig.)

  20. Noncarcinogenic effects of chromium: Update to health-assessment document. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Victery, W.; Lee, S.D.; Mushak, P.; Piscator, M.

    1990-04-01

    The document updates the 1984 Health Assessment Document for Chromium by addressing issues regarding noncarcinogenic health effects of chromium: oxidation states and persistence of these states in the environment, sampling and analytical methodology to differentiate these oxidation states and amounts at submicrogram ambient air levels, the degree of human exposure to chromium in the environment, both short-term and long-term, in vivo reduction of Cr (VI) to Cr (III), and effects from environmentally relevant levels on pulmonary function and renal function. Trivalent chromium is chemically stable; Cr (VI) is readily reduced to Cr (III). Oxidation state of chromium in ambient air depends on proximity to sources emitting one form over the other. Reliable monitoring methods to speciate oxidation states at ambient air levels below 1 microgram/cu m are not available. Ambient levels of total chromium (obtained from EPA's National Air Data Branch) range from a high of 0.6 microgram/cu m to below the detection limit of 0.005 microgram/cu m. Reduction of hexavalent chromium in vivo occurs in several organ systems and therefore, small amounts of inhaled Cr (VI) will be reduced before systemic absorption can occur. Trivalent chromium is an essential trace metal which potentiates actions of insulin-mediated glucose transport.

  1. Measuring cytotoxicity by bioluminescence imaging outperforms the standard chromium-51 release assay.

    Directory of Open Access Journals (Sweden)

    Mobin A Karimi

    Full Text Available The chromium-release assay developed in 1968 is still the most commonly used method to measure cytotoxicity by T cells and by natural killer cells. Target cells are loaded in vitro with radioactive chromium and lysis is determined by measuring chromium in the supernatant released by dying cells. Since then, alternative methods have been developed using different markers of target cell viability that do not involve radioactivity. Here, we compared and contrasted a bioluminescence (BLI-based cytotoxicity assay to the standard radioactive chromium-release assay using an identical set of effector cells and tumor target cells. For this, we stably transduced several human and murine tumor cell lines to express luciferase. When co-cultured with cytotoxic effector cells, highly reproducible decreases in BLI were seen in an effector to target cell dose-dependent manner. When compared to results obtained from the chromium release assay, the performance of the BLI-based assay was superior, because of its robustness, increased signal-to-noise ratio, and faster kinetics. The reduced/delayed detection of cytotoxicity by the chromium release method was attributable to the association of chromium with structural components of the cell, which are released quickly by detergent solubilization but not by hypotonic lysis. We conclude that the (BLI-based measurement of cytotoxicity offers a superior non-radioactive alternative to the chromium-release assay that is more robust and quicker to perform.

  2. The temperature gradient on section of casting in process of primary crystallization of chromium cast iron

    Directory of Open Access Journals (Sweden)

    A. Studnicki

    2008-08-01

    Full Text Available The methodology of defining in article was introduced the temperature gradient in process of primary crystallization during cooling the casting from chromium cast iron on basis of measurements of thermal field in test DTA-K3. Insert also the preliminary results of investigations of influence temperature gradient on structure of studied wear resistance chromium cast iron.

  3. Hexavalent chromium removal from wastewater using aniline formaldehyde condensate coated silica gel.

    Science.gov (United States)

    Kumar, P Albino; Ray, Manabendra; Chakraborty, Saswati

    2007-05-08

    A resinous polymer, aniline formaldehyde condensate (AFC) coated on silica gel was used as an adsorbent in batch system for removal of hexavalent chromium from aqueous solution by considering the effects of various parameters like reaction pH, dose of AFC coated silica gel, initial Cr(VI) concentration and aniline to formaldehyde ratio in AFC synthesis. The optimum pH for total chromium [Cr(VI) and Cr(III)] adsorption was observed as 3. Total chromium adsorption was second order and equilibrium was achieved within 90-120 min. Aniline to formaldehyde ratio of 1.6:1 during AFC synthesis was ideal for chromium removal. Total chromium adsorption followed Freundlich's isotherm with adsorption capacity of 65 mg/g at initial Cr(VI) 200mg/L. Total chromium removal was explained as combinations of electrostatic attraction of acid chromate ion by protonated AFC, reduction of Cr(VI) to Cr(III) and bond formation of Cr(III) with nitrogen atom of AFC. Almost 40-84% of adsorbed chromium was recovered during desorption by NaOH, EDTA and mineral acids. AFC coated silica gel can be effectively used for treatment of chromium containing wastewaters as an alternative.

  4. Environmental optimization of chromium recovery from tannery sludge using a life cycle assessment approach.

    Science.gov (United States)

    Kiliç, Eylem; Puig, Rita; Baquero, Grau; Font, Joaquim; Colak, Selime; Gürler, Deniz

    2011-08-15

    Life cycle assessment (LCA) was used to evaluate the environmental impact of an oxidative chromium recovery method from tannery sludge, in comparison with the usual landfilling process. Three improvement options (water reduction, byproduct use and anaerobic sludge digestion) were considered. The results showed that the proposed chromium recovery process would be better environmentally than conventional landfilling in all the evaluated impact categories if the amount of chromium recovered was 43 kg per ton of sludge. This amount could be recovered if the chromium concentration was about 20 times higher than that considered in this study. Alternatively, a lower chromium concentration would produce a better result if the recovery method was optimized and implemented at industrial rather than laboratory scale, and if more accurate data were provided on environmental credits for avoiding the chromium production process. Thus, the recovery method is environmentally beneficial when tannery sludge contains a chromium concentration of about 100,000 ppm. According to the literature, such concentrations are not unusual. The results could serve as the basis for further environmental improvements in chromium recovery and tannery sludge management and should be used in decision-making processes, especially for end-of-pipe treatments.

  5. The temperature gradient on section of casting in process of primary crystallization of chromium cast iron

    OpenAIRE

    2008-01-01

    The methodology of defining in article was introduced the temperature gradient in process of primary crystallization during cooling the casting from chromium cast iron on basis of measurements of thermal field in test DTA-K3. Insert also the preliminary results of investigations of influence temperature gradient on structure of studied wear resistance chromium cast iron.

  6. Tribological properties of the two-step thermally deposited chromium films

    NARCIS (Netherlands)

    Lazauskas, A.; Baltrusaitis, J.; Grigaliunas, V.; Baltusnikas, A.; Abakeviciene, B.; Polcar, T.

    2013-01-01

    Chromium thin films were prepared on glass substrate via a two-step thermal deposition and their structural, chemical and tribological properties were determined. The X-ray diffraction pattern of the two-step thermally deposited chromium film showed the presence of well-defined body-centered cubic C

  7. Leaching behavior of chromium in chrome shaving generated in tanning process and its stabilization.

    Science.gov (United States)

    Erdem, Mehmet; Ozverdi, Arzu

    2008-08-15

    In this study, leaching properties and pollution potential of chromium in chrome shaving (CS), which is a solid residue of leather industry, containing 2.27% Cr were investigated and thermal stabilization procedure was applied to the CS for chromium immobilization. For this purpose, firstly, effects of the liquid/solid ratio, contact time, pH and sequential extraction on the leaching behavior of chromium in the CS were studied. It was determined that the CS-caused chromium pollution is a hazardous material for environment. Thermal stabilization procedure was applied to the CS in the temperature range of 250-500 degrees C for the chromium immobilization. Effective stabilization of chromium in the CS was achieved by heating of CS at 350 degrees C under CO(2) atmosphere. Leaching experiments were also carried out with the samples obtained from the stabilization process and the results compared with that of the CS. Also, TCLP test method was applied to the samples to determine pollution potentials and discharge situations of the CS and its stabilization products. While the chromium concentrations in the test solutions of all samples stabilized thermally at above 350 degrees C were below the USEPA regulatory limit of 5 mg/l, the concentration of chromium leached out from the CS was 30-fold bigger than the USEPA regulatory limit.

  8. Kinetics of chromium ion absorption by cross-linked polyacrylate films

    Science.gov (United States)

    May, C. E.

    1984-01-01

    Three cross-linked ion exchange membranes were studied as to their ability to absorb chromium ion from aqueous chromium III nitrate solutions. Attention was given to the mechanism of absorption, composition of the absorbed product, and the chemical bonding. The membranes were: calcium polyacrylate, polyacrylic acid, and a copolymer of acrylic acid and vinyl alcohol. For the calcium polyacrylate and the copolymer, parabolic kinetics were observed, indicating the formation of a chromium polyacrylate phase as a coating on the membrane. The rate of absorption is controlled by the diffusion of the chromium ion through this coating. The product formed in the copolymer involves the formation of a coordination complex of a chromium ion with 6 carboxylic acid groups from the same molecule. The absorption of the chromium ion by the polyacrylic acid membranes appears to be more complicated, involving cross-linking. This is due to the coordination of the chromium ion with carboxylic acid groups from more than one polymer molecule. The absorption rate of the chromium ion by the calcium salt membrane was found to be more rapid than that by the free polyacrylic acid membrane.

  9. Redox Equilibria of Chromium in Calcium Silicate Base Melts

    Science.gov (United States)

    Mirzayousef-Jadid, A.-M.; Schwerdtfeger, Klaus

    2009-08-01

    The oxidation state of chromium has been determined at 1600 °C in CaO-SiO2-CrO x melts with CaO/SiO2 ratios (mass pct) of 0.66, 0.93, and 1.10, and 0.15 to 3.00 pct Cr2O3 (initial). A few experiments were also carried out with CaO-SiO2-Al2O3-CrO x melts at 1430 °C. The slag samples were equilibrated with gas phases of controlled oxygen pressure. Two techniques were applied to determine the oxidation state: thermogravimetry and quenching of the samples with subsequent wet chemical analysis. In the low-oxygen pressure range, the chromium is mainly divalent. In the high-oxygen pressure range, it is trivalent and hexavalent. It was found that the Cr3+/Cr2+ and Cr6+/Cr3+ ratios depend on oxygen pressure at a constant CaO/SiO2 ratio and a constant content of total chromium, according to the ideal law of mass action. According to the respective chemical reactions, these ratios change proportional to p_{{{text{O}}2 }}{}^{1/4} or p_{{{text{O}}_{ 2} }}{}^{3/4}, respectively. They also increase with increasing basicity. The data are used to compute the fractions of the different ions in the melt. There is a certain range of oxygen pressure in which all three valence states, Cr2+, Cr3+, and Cr6+, coexist. The color of the solidified slag samples is described and is explained with the help of transmission spectra.

  10. Chromium speciation in coal and biomass co-combustion products.

    Science.gov (United States)

    Stam, Arthur F; Meij, Ruud; Te Winkel, Henk; Eijk, Ronald J van; Huggins, Frank E; Brem, Gerrit

    2011-03-15

    Chromium speciation is vital for the toxicity of products resulting from co-combustion of coal and biomass. Therefore, understanding of formation processes has been studied using a combination of X-ray absorption fine structure (XAFS) spectroscopy and thermodynamic equilibrium calculations. The influence of cofiring on Cr speciation is very dependent on the type of fuel. Cr(VI) contents in the investigated fly ash samples from coal and cofiring average around 7% of the total chromium. An exception is cofiring 7-28% wood for which ashes exhibited Cr(VI) concentrations of 12-16% of the total chromium. Measurements are in line with thermodynamic predictions: RE factors of Cr around 1 are in line with volatile Cr only above 1400 °C; lower Cr(VI) concentrations with lower oxygen content and Cr(III) dissolved in aluminosilicate glass. Stability of Cr(VI) below 700 °C does not correlate with Cr(VI) concentrations found in the combustion products. It is indicated that Cr(VI) formation is a high-temperature process dependent on Cr evaporation (mode of occurrence in fuel, promoted by organic association), oxidation (local oxygen content), and formation of solid chromates (promoted by presence of free lime (CaO) in the ash). CaCrO(4)(s) is a probable chemical form but, given different leachable fractions (varying from 25 to 100%), different forms of Cr(VI) must be present. Clay-bound Cr is likely to dissolve in the aluminosilicate glass phase during melting of the clay.

  11. Chromium(III) complexes of naturally occurring ligands

    Science.gov (United States)

    El-Shahawi, M. S.

    1995-02-01

    Chromium(III) complexes prepared from CrCl 3Py 3 and anhydrous CrCl 3 with L(-)-threonine, nicotinic acid, glycine, D(-)-penicillamine, L(-)-cysteine and L(-)-cystine have been characterized. The magnetic moments (3.4-4.05 B.M.) are close to the spin only value for a d3 chromium(III) ion in octahedral or pseudo octahedral symmetry. In the electronic spectra two sharp peaks are observed at (15.9-19.8) × 10 3 and (22.0-26.7) × 10 3 cm -1 and are assigned to d-d transitions in the pseudo octahedral configuration. The parameters ( Dq, B, β35) and the interelectronic repulsion parameter with the ionic charge, Z∗, are calculated and place the ligand in the middle of the spectrochemical series. In the circular dichroism spectra three Cotton effects are observed in the forbidden band of the optically active chelates and are assigned to the 2E( 2Eg), 2A 2( 2T 1g) and2E( 2T 1g) while that in the spin allowed band are a result of the splitting of the 4A 2g( 4T 2g) to 4A 1( 4T 2g) and4E( 4T 2g) transitions. The structure of threonine, cystine and cysteine chelates are likely to be fac since strong and well defined Cotton effects are observed. The Cotton effects of penicillamine chelates are weak suggesting formation of the mer structure. Prolonged heating or bubbling air through the solution of CrCl 3Py 3 containing L(-)-threonine, glycine or nicotinic acid for several hours enhances chromium(VI) formation.

  12. Chromium Isotopes Record Fluctuations in Precambrian Biospheric Oxygenation

    Science.gov (United States)

    Frei, R.; Gaucher, C.; Poulton, S. W.; Canfield, D. E.

    2009-12-01

    There is a direct relationship between life, oxygen, and the surface chemistry of the Earth. Geochemical data suggest that oxygenation of the Earth's atmosphere occurred in two broad steps, near the beginning and the end of the Proterozoic Eon (2500 to 542 million years ago), but the details of this history are unclear. The geochemical behaviour of chromium (Cr) is highly sensitive to the redox state of the surface environment as oxidative weathering processes produce the oxidised hexavalent [Cr(VI)] form. Oxidation of reduced trivaltent [Cr(III)] chromium on land is accompanied by an isotopic fractionation, leading to enrichment of the mobile hexavalent form in the heavier isotope. The fractionated Cr isotope signature is then tranfered by riverine transport to the sea. Here, we use Cr stable isotopes from banded iron formations (BIFs) to track the presence of Cr(VI) in Precambrian oceans, providing a time-resolved picture of the oxygenation history of Earth’s atmosphere-hydrosphere system. Fractionated Cr isotopes indicate the accumulation of Cr(VI) in ocean surface waters ~2.8 to 2.6 billion years (Gyr) ago and a likely transient elevation in atmospheric and surface ocean oxygen prior to the first great rise of oxygen 2.45-2.2 Gyr ago (the Great Oxidation Event; GOE). In contrast, Cr isotopes in ~1.88 Gyr old BIFs are not fractionated, indicating a major decline in atmospheric oxygen and demonstrating that the GOE did not lead to a unidirectional stepwise increase in atmospheric oxygen. In the late Neoproterozoic, ~800 to 542 million years (Myr) ago, we observe strong positive fractionations in Cr isotopes (δ53Cr up to +4.9 ‰) providing independent support for increased surface oxygenation at this time. This may have stimulated rapid evolution of macroscopic multicellular life. Our chromium isotope data thus provide new insights into the oxygenation history of the Earth, and highlight its use as a powerful redox tracer in aquatic systems.

  13. Chromium removal from electroplating wastewater by coir pith.

    Science.gov (United States)

    Suksabye, Parinda; Thiravetyan, Paitip; Nakbanpote, Woranan; Chayabutra, Supanee

    2007-03-22

    Coir pith is a by-product from padding used in mattress factories. It contains a high amount of lignin. Therefore, this study investigated the use of coir pith in the removal of hexavalent chromium from electroplating wastewater by varying the parameters, such as the system pH, contact time, adsorbent dosage, and temperature. The maximum removal (99.99%) was obtained at 2% (w/v) dosage, particle size <75microm, at initial Cr(VI) 1647mgl(-1), system pH 2, and an equilibrium time of 18h. The adsorption isotherm of coir pith fitted reasonably well with the Langmuir model. The maximum Cr(VI) adsorption capacity of coir pith at 15, 30, 45 and 60 degrees C was 138.04, 197.23, 262.89 and 317.65mgCr(VI)g(-1) coir pith, respectively. Thermodynamic parameters indicated an endothermic process and the adsorption process was favored at high temperature. Desorption studies of Cr(VI) on coir pith and X-ray absorption near edge structure (XANES) suggested that most of the chromium bound on the coir pith was in Cr(III) form due to the fact that the toxic Cr(VI) adsorbed on the coir pith by electrostatic attraction was easily reduced to less toxic Cr(III). Fourier transform infrared (FT-IR) spectrometry analysis indicated that the carbonyl (CO) groups and methoxy (O-CH(3)) groups from the lignin structure in coir pith may be involved in the mechanism of chromium adsorption. The reduced Cr(III) on the coir pith surface may be bound with CO groups and O-CH(3) groups through coordinate covalent bonding in which a lone pair of electrons in the oxygen atoms of the methoxy and carbonyl groups can be donated to form a shared bond with Cr(III).

  14. Chromium removal from electroplating wastewater by coir pith

    Energy Technology Data Exchange (ETDEWEB)

    Suksabye, Parinda [The Joint School of Energy and Environment, King Mongkut' s University of Technology Thonburi, 91 Pracha-Utit Road, Bangmod, Thungkru, Bangkok 10140 (Thailand); Thiravetyan, Paitip [Division of Biotechnology, School of Bioresources and Technology, King Mongkut' s University of Technology Thonburi, 83 Moo. 8 Thakham, Bangkhuntien, Bangkok 10150 (Thailand)]. E-mail: paitip.thi@kmutt.ac.th; Nakbanpote, Woranan [Pilot Plant Development and Training Institute, King Mongkut' s University of Technology Thonburi, 83 Moo. 8 Thakham, Bangkhuntien, Bangkok 10150 (Thailand); Chayabutra, Supanee [Department of Chemistry, Faculty of Science, Silpaorn University, 6 Rajamankhanai Road, Amphoe Muang, Nakorn Pathom Province, Bangkok 73000 (Thailand)

    2007-03-22

    Coir pith is a by-product from padding used in mattress factories. It contains a high amount of lignin. Therefore, this study investigated the use of coir pith in the removal of hexavalent chromium from electroplating wastewater by varying the parameters, such as the system pH, contact time, adsorbent dosage, and temperature. The maximum removal (99.99%) was obtained at 2% (w/v) dosage, particle size <75 {mu}m, at initial Cr(VI) 1647 mg l{sup -1}, system pH 2, and an equilibrium time of 18 h. The adsorption isotherm of coir pith fitted reasonably well with the Langmuir model. The maximum Cr(VI) adsorption capacity of coir pith at 15, 30, 45 and 60 deg. C was 138.04, 197.23, 262.89 and 317.65 mg Cr(VI) g{sup -1} coir pith, respectively. Thermodynamic parameters indicated an endothermic process and the adsorption process was favored at high temperature. Desorption studies of Cr(VI) on coir pith and X-ray absorption near edge structure (XANES) suggested that most of the chromium bound on the coir pith was in Cr(III) form due to the fact that the toxic Cr(VI) adsorbed on the coir pith by electrostatic attraction was easily reduced to less toxic Cr(III). Fourier transform infrared (FT-IR) spectrometry analysis indicated that the carbonyl (C=O) groups and methoxy (O-CH{sub 3}) groups from the lignin structure in coir pith may be involved in the mechanism of chromium adsorption. The reduced Cr(III) on the coir pith surface may be bound with C=O groups and O-CH{sub 3} groups through coordinate covalent bonding in which a lone pair of electrons in the oxygen atoms of the methoxy and carbonyl groups can be donated to form a shared bond with Cr(III)

  15. MICROSTRUCTURE AND CORROSION RESISTANCE OF CHROMIUM NITRIDES OBTAINED BY VACUUM GAS NITRIDING OF ELECTROLYTIC CHROMIUM DEPOSITED ON AISI H13 STEEL

    Directory of Open Access Journals (Sweden)

    H. Cifuentes

    2013-06-01

    Full Text Available In this scientific research paper, the microstructure and corrosion resistance of chromium nitrides obtained from a duplex treatment consisting of an electroplated hard chromium coating applied on a steel AISI H13 follow by a thermochemical treatment in vacuum using NH3 as precursor gas of nitrogen, is evaluated. This type of duplex treatments combine the benefits of each individual treatment in order to obtain, with this synergic effect, compounds type CrxN more economic than those obtained by other kind of treatments e.g. physical vapor deposition (PVD. The results obtained by X-Ray Diffraction (XRD indicate the surface and subsurface transformation of the electrolytic hard chromium coating by formation of CrN and Cr2N phases. Likewise, potentiodynamic polarization tests indicate an increase in corrosion resistance of such kind of compounds in comparison with the obtained results with electroplated hard chromium.

  16. Chromium removal by zeolite-rich materials obtained from an exhausted FCC catalyst: Influence of chromium incorporation on the sorbent structure.

    Science.gov (United States)

    Gonzalez, Maximiliano R; Pereyra, Andrea M; Torres Sánchez, Rosa M; Basaldella, Elena I

    2013-10-15

    A spent FCC catalyst was converted into a zeolitic mixture, and the product obtained was afterward used as trapping material for Cr(III) species frequently found in aqueous solutions. Eventual changes in the sorbent structure produced by Cr incorporation were studied by different characterization techniques such as point of zero charge determinations (PZC), X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX), and infrared absorption (FTIR). The XRD and FTIR analyses indicated that chromium incorporation produces an amorphization of the material, and PZC measurements show no surface adsorption of charged chromium species. SEM and EDX analyses clearly show that after chromium sorption, the initial microspheroidal catalyst morphology was maintained, and the presence of chromium species was mainly detected in the outer microsphere surface, where the zeolite crystals were hydrothermally grown.

  17. Type 2 diabetic rats on diet supplemented with chromium malate show improved glycometabolism, glycometabolism-related enzyme levels and lipid metabolism.

    Directory of Open Access Journals (Sweden)

    Weiwei Feng

    Full Text Available Our previous study showed that chromium malate improved the regulation of blood glucose in mice with alloxan-induced diabetes. The present study was designed to evaluate the effect of chromium malate on glycometabolism, glycometabolism-related enzymes and lipid metabolism in type 2 diabetic rats. Our results showed that fasting blood glucose, serum insulin level, insulin resistance index and C-peptide level in the high dose group had a significant downward trend when compared with the model group, chromium picolinate group and chromium trichloride group. The hepatic glycogen, glucose-6-phosphate dehydrogenase, glucokinase, Glut4, phosphor-AMPKβ1 and Akt levels in the high dose group were significantly higher than those of the model, chromium picolinate and chromium trichloride groups. Chromium malate in a high dose group can significantly increase high density lipoprotein cholesterol level while decreasing the total cholesterol, low density lipoprotein cholesterol and triglyceride levels when compared with chromium picolinate and chromium trichloride. The serum chromium content in chromium malate and chromium picolinate group is significantly higher than that of the chromium trichloride group. The results indicated that the curative effects of chromium malate on glycometabolism, glycometabolism-related enzymes and lipid metabolism changes are better than those of chromium picolinate and chromium trichloride. Chromium malate contributes to glucose uptake and transport in order to improved glycometabolism and glycometabolism-related enzymes.

  18. Microstructure and properties of Ti–Nb–V–Mo-alloyed high chromium cast iron

    Indian Academy of Sciences (India)

    Youping Ma; Xiulan Li; Yugao Liu; Shuyi Zhou; Xiaoming Dang

    2013-10-01

    The correlations of microstructure, hardness and fracture toughness of high chromium cast iron with the addition of alloys (titanium, vanadium, niobium and molybdenum) were investigated. The results indicated that the as-cast microstructure changed from hypereutectic, eutectic to hypoeutectic with the increase of alloy contents. Mo dissolved in austenite and increased the hardness by solid solution strengthening. TiC and NbC mainly existed in austenite and impeded the austenite dendrite development. V existed in multicomponent systems in forms of V alloy compounds (VCrFe8 and VCr2C2).With the increase of alloy additions, carbides size changed gradually from refinement to coarseness, hardness and impact toughness were increased and then decreased. Compared with the fracture toughness (6 J/cm2) and hardness (50.8HRC) without any alloy addition, the toughness and hardness at 0.60 V–0.60Ti–0.60Nb–0.35Mo (wt%) additions were improved and achieved to 11 J/cm2 and 58.9HRC, respectively. The synergistic roles of Ti, Nb, V and Mo influenced the solidification behaviour of alloy. The refinement of microstructure and improvement of carbides morphologies, size and distribution improved the impact toughness.

  19. Chromium Renderserver: Scalable and Open Source Remote RenderingInfrastructure

    Energy Technology Data Exchange (ETDEWEB)

    Paul, Brian; Ahern, Sean; Bethel, E. Wes; Brugger, Eric; Cook,Rich; Daniel, Jamison; Lewis, Ken; Owen, Jens; Southard, Dale

    2007-12-01

    Chromium Renderserver (CRRS) is software infrastructure thatprovides the ability for one or more users to run and view image outputfrom unmodified, interactive OpenGL and X11 applications on a remote,parallel computational platform equipped with graphics hardwareaccelerators via industry-standard Layer 7 network protocolsand clientviewers. The new contributions of this work include a solution to theproblem of synchronizing X11 and OpenGL command streams, remote deliveryof parallel hardware-accelerated rendering, and a performance analysis ofseveral different optimizations that are generally applicable to avariety of rendering architectures. CRRSis fully operational, Open Sourcesoftware.

  20. Evaluating Foraminifera as an Archive for Seawater Chromium Isotopic Composition

    Science.gov (United States)

    Wang, X.; Planavsky, N.; Hull, P. M.; Tripati, A.; Reinhard, C.; Zou, H.; Elder, L. E.; Henehan, M. J.

    2015-12-01

    In recent years there has been growing interest in using chromium isotopes (δ53Cr) as a proxy to investigate the redox evolution of Earth's ocean-atmosphere system throughout geological history. Potential archives for seawater δ53Cr that have been identified to date include iron formations and organic-rich siliciclastic sediments. However, these types of sediments are not common and they are discontinuous over geologic time. As a result, alternative types of archives are needed. Here we evaluate the utility of foraminifera tests as a recorder of seawater δ53Cr. Core-tops used were from different ocean basins. Mono-specific samples of Globigerinoides sacculifer, Orbulina universa, Pulleniatina obliquiloculata, Globoratalia crassula-crassaformis, Globoratalia truncatulinoides, and Globigerinella siphonifera were isolated to investigate inter-species isotope fractionation. Chromium concentrations were measured by isotope dilution method to be 0.1-0.3 μg/g. The δ53Cr values of these species range from 0.2‰ to 2.4‰, with an analytical uncertainty of 0.3‰ (95% confidence). Despite the high analytical uncertainty due to the extremely low levels of Cr present, there is still large detectable variation in foraminiferal δ53Cr values, which overlap presently available seawater values (Bonnand et al., 2013; Scheiderich et al., 2015). Possible explanations for such variations in foraminiferal δ53Cr values include heterogeneity of seawater δ53Cr in the modern oceans, and/or photobiochemical redox cycling of Cr in the surface oceans. Therefore, care should be taken when using foraminifera to reconstruct past seawater δ53Cr values. ReferencesBonnand, P., James, R., Parkinson, I., Connelly, D., Fairchild, I., 2013. The chromium isotopic composition of seawater and marine carbonates. Earth and Planetary Science Letters, 382: 10-20. Scheiderich, K., Amini, M., Holmden, C., Francois, R., 2015. Global variability of chromium isotopes in seawater demonstrated by Pacific

  1. Adsorption of chromium ion (VI) by acid activated carbon

    OpenAIRE

    A. A. Attia; Khedr,S. A.; Elkholy,S. A.

    2010-01-01

    The activated carbon produced from olive stones was chemically activated using sulfuric acid, (OS-S), and utilized as an adsorbent for the removal of Cr(VI) from aqueous solution in the concentration range 4-50 mg/L. Adsorption experiments were carried out in a batch process and various experimental parameters such as effect of contact time, initial chromium ion concentration, carbon dosage, and pH on percentage removal have been studied. Adsorption results obtained for activated carbon (OS-S...

  2. Structural, morphological and optical properties of chromium oxide nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Babukutty, Blessy; Parakkal, Fasalurahman; Nair, Swapna S., E-mail: swapna.s.nair@gmail.com [School of Mathematical and Physical Sciences, Department of Physics, Central University of Kerala, Kasaragod 671314 (India); Bhalero, G. M. [UGC-DAE, IGCAR, Kalpakkam, TamilNadu (India); Aravind, P. B. [Cochin University of Science and Technology(CUSAT), Cochin (India)

    2015-06-24

    Chromium oxide nanoparticles are synthesized by reduction route from chloride precursors with surfactant, trioctylphosphine oxide (TOPO). Structural and morphological characterization are analyzed using X-ray Diffraction (XRD) and Transmission Electron Microscopy (TEM). Transmission Electron micrographs show that the average grain size lies in the range 5nm to 10nm. Optical characterization has been done by UV-VIS spectrophotometer. Distinct optical absorptions of Cr{sup 3+} ions show hinting towards the presence of Cr{sub 2}O{sub 3}. Presence of oxygen is also confirmed from Electron Energy Loss Spectroscopy (EELS) studies.

  3. MODELING THE RATE-CONTROLLED SORPTION OF HEXAVALENT CHROMIUM.

    Science.gov (United States)

    Grove, D.B.; Stollenwerk, K.G.

    1985-01-01

    Sorption of chromium VI on the iron-oxide- and hydroxide-coated surface of alluvial material was numerically simulated with rate-controlled reactions. Reaction kinetics and diffusional processes, in the form of film, pore, and particle diffusion, were simulated and compared with experimental results. The use of empirically calculated rate coefficients for diffusion through the reacting surface was found to simulate experimental data; pore or particle diffusion is believed to be a possible rate-controlling mechanism. The use of rate equations to predict conservative transport and rate- and local-equilibrium-controlled reactions was shown to be feasible.

  4. CHROMIUM EXTRACTION BY MICROEMULSIONS IN TWO- AND THREE-PHASE SYSTEMS

    Directory of Open Access Journals (Sweden)

    K. R. O. Melo

    2015-12-01

    Full Text Available Abstract Microemulsion systems were used to remove chromium from an aqueous solution obtained from acid digestion of tannery sludge. The systems were composed by: coconut oil soap as surfactant, 1-butanol as cosurfactant, kerosene as the oil phase, and chromium solution as the aqueous phase. Two- and three-phase microemulsion extraction methods were investigated in the experiments. Viscosity, effective diameter of the droplets, and extraction and re-extraction efficiencies were evaluated for each system. Two- and three-phase systems showed small variations in droplet diameter, which can be attributed to the formation of micellar structures. Chromium recovery efficiencies for the studied systems were over 96%. The re-extraction step showed that the stripping solution used can release more than 96% of the chromium from the microemulsion phase. Experimental results confirm that chromium can be recovered efficiently using microemulsion systems.

  5. Detergents and bleaches are sources of chromium contact dermatitis in Israel

    DEFF Research Database (Denmark)

    Ingber, A; Gammelgaard, Bente; David, M

    1998-01-01

    Total chromium levels were determined in 38 detergents and 12 bleaches on the market in Israel (45 locally produced, 5 imported). The samples were analyzed by Zeeman-corrected graphite furnace atomic absorption spectrophotometry. Chromium levels were higher than 5 ppm in 28 (56%) of the 50 products......, from 1 to 5 ppm in 16 (32%), and lower than 1 ppm in only 6 (12%). Among the 5 imported products, only 1 had a chromium level below 1 ppm and the other 4 (1 from Germany, 3 from the USA) had high levels. Since a most 90% of the detergents and bleaches examined contained chromium levels higher than 1...... ppm, it is concluded that these consumer products may be the cause of the high incidence of chromium sensitivity in Israel....

  6. Development of Alkaline Oxidative Dissolution Methods for Chromium (III) Compounds Present in Hanford Site Tank Sludges

    Energy Technology Data Exchange (ETDEWEB)

    NN Krot; VP Shilov; AM Fedoseev; NA Budantseva; MV Nikonov; AB Yusov; AYu Garnov; IA Charushnikova; VP Perminov; LN Astafurova; TS Lapitskaya; VI Makarenkov

    1999-07-02

    The high-level radioactive waste sludge in the underground storage tanks at the Hanford Site contains various chromium(III)solid phases. Dissolution and removal of chromium from tank waste sludges is desirable prior to high-level waste vitrification because increased volume is required to incorporate the residual chromium. Unfortunately, dissolution of chromium from the sludge to form Cr(OH){sub 4}{sup {minus}} through treatment with heated NaOH solution (also used to dissolve aluminum phases and metathesize phosphates to sodium salts) generally has been unsuccessful in tests with both simulated and genuine Hanford waste sludges. Oxidative dissolution of the Cr(III) compounds to form soluble chromate has been proposed as an alternative chromium solid phase dissolution method and results of limited prior testing have been reported.

  7. Bioremediation of the soils contaminated with cadmium and chromium, by the earthworm Eisenia fetida.

    Directory of Open Access Journals (Sweden)

    E Aseman

    2016-01-01

    Results: There was a significant correlation between the reduction of chromium and cadmium metals in the soils and the accumulation of chromium and cadmium metals in the worm’s body. A significant decline of chromium levels of the soil was observed in the days 21 and 42 during the study compared to the initial amount of 0.1 mg/g. On the other hand, chromium concentration of the soil decreased from 0.14 to 0.1 mg/g after 42 days. Conclusion: said the research indicated that increased mortality of worms in the soil at a concentration of 0.08 mg/g of chromium, using the worms for bioremediation is not recommended. Although, this method is effective to remove cadmium from the soils having cadmium with concentrations of 0.04 and 0.08 mg/g but it needs further investigation.

  8. Chromium related degradation of solid oxide fuel cells; Chrom-bezogene Degradation von Festoxid-Brennstoffzellen

    Energy Technology Data Exchange (ETDEWEB)

    Neumann, Anita

    2011-05-04

    Solid Oxide Fuel Cells (SOFCs) offer a high potential for application as an auxiliary power unit (APU) for heavy goods vehicles as well as combined heat and power (CHP) systems. SOFCs are especially attractive due to their high efficiencies and the use of different fuel types. However, optimization in terms of long term stability and costs are still necessary. This work characterized the degradation of SOFCs with lanthanum strontium manganite (LSM) cathodes under chromium influence. Galvanostatic cell tests were carried out at 800 C with operation times from 250 - 3000 h and variation of the chromium source and current density. The current densities of j = 0 (A)/(cm{sup 2}), j = 0,3 (A)/(cm{sup 2}) and j = 0,5 (A)/(cm{sup 2}) were applied. The high temperature ferritic alloy Crofer22APU was used as a chromium source. Variation of the chromium source was realized by coating the Crofer22APU insert with the chromium retention layer Mn{sub 3}O{sub 4} and the cathode contact layer LCC10. Cell degradation was analyzed with regard to cell voltage, current density and area specific resistance (ASR). Microstructural alterations of the cathode as well as chromium content and distribution across the cell were investigated after completion of the cell tests. For cells with a chromium source present and operation with a nonzero current density, the course of cell degradation was divided into three phases: a run-in, weak linear degradation and strong linear degradation. A decrease of the chromium release rate by means of different coatings stretched the course of degradation along the timescale. Strong degradation, which is characterized by a significant increase in ASR as well as a decrease of current density at the operating point, was only observed when a chromium source in the setup was comb ined with operation of the cell with a non-zero current density. Operation of the cell with a chromium source but no current density caused a degradation of current density at the

  9. Standard specification for Nickel-Chromium-Iron alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045 and N06696), Nickel-Chromium-Cobalt-Molybdenum alloy (UNS N06617), and Nickel-Iron-Chromium-Tungsten alloy (UNS N06674) plate, sheet and strip

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2011-01-01

    Standard specification for Nickel-Chromium-Iron alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045 and N06696), Nickel-Chromium-Cobalt-Molybdenum alloy (UNS N06617), and Nickel-Iron-Chromium-Tungsten alloy (UNS N06674) plate, sheet and strip

  10. Standard specification for Nickel-Chromium-Iron alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696), Nikel-Chromium-Cobalt-Molybdenum alloy (UNS N06617), and Nickel-Iron-Chromium-Tungsten alloy (UNS N06674) seamless pipe and tube

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2011-01-01

    Standard specification for Nickel-Chromium-Iron alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696), Nikel-Chromium-Cobalt-Molybdenum alloy (UNS N06617), and Nickel-Iron-Chromium-Tungsten alloy (UNS N06674) seamless pipe and tube

  11. Standard specification for Nickel-Chromium-Iron alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696), Nickel-Chromium-Cobalt-Molybdenum alloy (UNS N06617), and Nickel-Iron-Chromium-Tungsten alloy (UNS N06674) rod, bar, and wire

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2011-01-01

    Standard specification for Nickel-Chromium-Iron alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696), Nickel-Chromium-Cobalt-Molybdenum alloy (UNS N06617), and Nickel-Iron-Chromium-Tungsten alloy (UNS N06674) rod, bar, and wire

  12. The Effect of Slag on the Effectiveness of Phosphorus Removal from Ferrous Alloys Containing Carbon, Chromium and Nickel

    Directory of Open Access Journals (Sweden)

    Kawecka-Cebula E.

    2016-03-01

    Full Text Available The aim of this study was to determine the impact of slag composition on phosphorus removal from ferrous solutions containing carbon, chromium and nickel. Additions of cryolite, Na3AlF6, were applied for better fluxing and higher phosphate capacity of the slag. An X-ray analysis of final slags formed during dephosphorization of ferrous solutions containing chromium and nickel with CaO-CaF2 or CaO-CaF2-Na3AlF6 mixtures of different chemical compositions was carried out. The equilibrium composition of the liquid and the solid phase while cooling the slags from 1673K to 298K was computed using FactSage 6.2 software. The performed equilibrium computations indicated that the slags were not entirely liquid at those temperatures. The addition of cryolite causes a substantial increase of the liquid phase of the slag. It also has a favourable effect on the dephosphorization grade of hot metal. The obtained results were statistically processed and presented in the form of regression equations.

  13. Airborne exposure to inhalable hexavalent chromium in welders and other occupations: Estimates from the German MEGA database.

    Science.gov (United States)

    Pesch, Beate; Kendzia, Benjamin; Hauptmann, Kristin; Van Gelder, Rainer; Stamm, Roger; Hahn, Jens-Uwe; Zschiesche, Wolfgang; Behrens, Thomas; Weiss, Tobias; Siemiatycki, Jack; Lavoué, Jerome; Jöckel, Karl-Heinz; Brüning, Thomas

    2015-07-01

    This study aimed to estimate occupational exposure to inhalable hexavalent chromium (Cr(VI)) using the exposure database MEGA. The database has been compiling Cr(VI) concentrations and ancillary data about measurements at German workplaces. We analysed 3659 personal measurements of inhalable Cr(VI) collected between 1994 and 2009. Cr(VI) was determined spectrophotometrically at 540 nm after reaction with diphenylcarbazide. We assigned the measurements to pre-defined at-risk occupations using the information provided about the workplaces. Two-thirds of the measurements were below the limit of quantification (LOQ) and multiply imputed according to the distribution above LOQ. The 75th percentile value was 5.2 μg/m(3) and the 95th percentile was 57.2 μg/m(3). We predicted the geometric mean for 2h sampling in the year 2000, and the time trend of Cr(VI) exposure in these settings with and without adjustment for the duration of measurements. The largest dataset was available for welding (N = 1898), which could be further detailed according to technique. The geometric means were above 5 μg/m(3) in the following situations: spray painting, shielded metal arc welding, and flux-cored arc welding if applied to stainless steel. The geometric means were between 1 μg/m(3) and 5 μg/m(3) for gas metal arc welding of stainless steel, cutting, hard-chromium plating, metal spraying and in the chemical chromium industry. The exposure profiles described here are useful for epidemiologic and industrial health purposes. Exposure to Cr(VI) varies not only between occupations, but also within occupations as shown for welders. In epidemiologic studies, it would be desirable to collect exposure-specific information in addition to the job title.

  14. Speciation of chromium in bread and breakfast cereals.

    Science.gov (United States)

    Mathebula, Mpho Wendy; Mandiwana, Khakhathi; Panichev, Nikolas

    2017-02-15

    Bread and breakfast cereals are a major constituents of the human diet, yet their Cr(VI) content is not known. Chromium(VI) was determined in these products by high resolution continuum source atomic absorption spectrometer (HR-CS AAS) after leaching Cr(VI) with 0.10molL(-1) Na2CO3. The results showed that 33-73% of total Cr (58.17±5.12μgkg(-1)-156.1±6.66μgkg(-1)) in bread exist as Cr(VI) and the highest total Cr content was found in brown bread. It was shown that Cr(III) is oxidized to Cr(VI) during toasting of bread. Chromium(VI) content in breakfast cereals ranged between 20.4±4μgkg(-1) and 470.4±68μgkg(-1). Therefore, it can be concluded that bread and breakfast cereals contains Cr(VI) which does not exceed maximum acceptable concentration (MAC) of 0.003mgkg(-1)bw(-1)day(-1) through daily consumption of half a bowl (65g) of breakfast cereal and four slices of toasted (122g) or untoasted bread (160g).

  15. Biosorption of aqueous chromium(VI) by Tamarindus indica seeds.

    Science.gov (United States)

    Agarwal, G S; Bhuptawat, Hitendra Kumar; Chaudhari, Sanjeev

    2006-05-01

    The effectiveness of low cost agro-based materials namely, Tamarindus indica seed (TS), crushed coconut shell (CS), almond shell (AS), ground nut shell (GS) and walnut shell (WS) were evaluated for Cr(VI) removal. Batch test indicated that hexavalent chromium sorption capacity (q(e)) followed the sequence q(e)(TS) > q(e)(WS) > q(e)(AS) > q(e)(GS) > q(e)(CS). Due to high sorptive capacity, tamarind seed was selected for detailed sorption studies. Sorption kinetic data followed first order reversible kinetic fit model for all the sorbents. The equilibrium conditions were achieved within 150 min under the mixing conditions employed. Sorption equilibria exhibited better fit to Freundlich isotherms (R>0.92) than Langmuir isotherm (R approximately = 0.87). Hexavalent chromium sorption by TS decreased with increase in pH, and slightly reduced with increase in ionic strength. Cr(VI) removal by TS seems to be mainly by chemisorption. Desorption of Cr(VI) from Cr(VI) laden TS was quite less by distilled water and HCl. Whereas with NaOH, maximum desorption achieved was about 15.3%. When TS was used in downflow column mode, Cr(VI) removal was quite good but head loss increased as the run progressed and was stopped after 200 h.

  16. Structural effects of metallic chromium on its electrochemical behavior

    Directory of Open Access Journals (Sweden)

    VELIMIR RADMILOVIC

    2007-06-01

    Full Text Available Chromium dissolution in aqueous sulfuric acid solution of pH 1 was studied electrochemically on chromium electrodes with different crystallographic structures. A slow potentiodynamic method was used for the electrochemical measurements in deaerated solutions (purgedwith nitrogen,while the Cr(III ions in the solution after the corrosion were determined by atomic absorption spectrometry. Three electrode materials with a very dominant crystallite orientation resembling single crystal structures (i.e., 111 and 110 confirmed by the electron backscattering diffraction (EBSD, were used in the experiments. The (111 structures were somewhat more active electrochemically (both anodic and cathodic than the (110 structure. However, Cr electrochemically deposited in standard plating bath, assumed from literature data to has also the (111 structure, was more than 4 times active for anodic dissolution and, by the same number, less active for cathodic hydrogen evolution. The concentrations of Cr(III ions determined in the solution after definite times of corrosion of all the materials showed almost two times larger dissolution rates than observed electrochemically by three different electrochemical methods (Wagner–Traud, Stern–Geary, electrochemical impedance spectroscopy. This is explained by the simultaneous occurrence of potential independent chemical dissolution of Cr, by a direct reaction of metallic Cr with H2O molecules, proposed a long time ago by Kolotyrkin and coworkers.

  17. Pseudo-Stem Banana Fibers: Characterization and Chromium Removal

    Directory of Open Access Journals (Sweden)

    Helena Becker

    2013-11-01

    Full Text Available In this work, pseudo-stems of the banana tree were collected, characterized and used as adsorbent materials for the removal of the chromium ions from aqueous solution. The characterization of pseudo-stems by FTIR suggests the presence of cellulose, hemicellulose and lignin. The predominant groups were carbonyls (0.312 ± 0.010 mmol g–1 adsorbent, phenols (0.237 ± 0.021 mmol g–1 adsorbent, lactones (0.041 ± 0.003 mmol g–1 adsorbent and basic groups (0.096 ± 0.006 mmol g–1 adsorbent. The textural propriety of the adsorbent, surface area, pore volume and pore diameter were found to be 0.383 m2 g–1, 0.003525 cm3 g–1 and 368.3 Å, respectively. The pHpzc value was found 7.5 and so the adsorption assays of chromium removal from solution were more efficiently at acidic pH values. The experiments show that approximately 95% and 78% of the Cr (VI was removed from solution by untreated and treated fiber, respectively, in 300 minutes of the contact time.

  18. Internal Friction In The PFN Ceramics With Chromium Dopand

    Directory of Open Access Journals (Sweden)

    Zachariasz R.

    2015-09-01

    Full Text Available An aim of this work was to determine an influence of an admixture, the chromium (for x from 0.01 to 0.06, on the mechanical properties of the PFN ceramics. The ceramics with chemical composition Pb(Fe0.5−xCrxNb0.5O3 was synthesized in two steps from simple oxides PbO, Fe2O3, Nb2O5, Cr2O3. The first stage was based on obtaining the FeNbO4 from the Fe2O3 and Nb2O5 simple oxides. At this stage an admixture in a form the Cr2O3 chromium oxide was added to the solution. In the second stage the PbO lead oxide and the doped FeNbO4 (obtained earlier were synthetized. The sintering of ceramic samples PFCN type was carried out by free sintering method. Temperature measurements of the internal friction were conducted on a computer-controlled automatic resonant mechanical spectrometer (heating cycle with 3 deg/min.

  19. Study of effect of chromium on titanium dioxide phase transformation

    Indian Academy of Sciences (India)

    A Bellifa; L Pirault-Roy; C Kappenstein; A Choukchou-Braham

    2014-05-01

    MTi samples with different atomic chromium percentages were synthesized by sol–gel method and calcined at 400 °C under air. The effects of Cr and temperature on titanium dioxide phase transition were studied. In situ measurement showed the presence of anatase phase for all samples at temperature < 500 °C. Without Cr content, the anatase–rutile transition takes place at 600 °C and the rutile fraction increases with increase of temperature. In the presence of Cr content, rutile phase appeared at 700 °C. Cr2O3 phase was shown only in the case of CrTi20 content at 800 °C which indicates that the segregation remains modest. We have also studied the anatase–rutile transition kinetics by using in situ X-ray measurements. It was found that the anatase phase stability increases as the chromium content increases. Results confirm that the transformation of anatase–rutile is of first order.

  20. Soil microbial community response to hexavalent chromium in planted and unplanted soil.

    Science.gov (United States)

    Ipsilantis, Ioannis; Coyne, Mark S

    2007-01-01

    Theories suggest that rapid microbial growth rates lead to quicker development of metal resistance. We tested these theories by adding hexavalent chromium [Cr(VI)] to soil, sowing Indian mustard (Brassica juncea), and comparing rhizosphere and bulk soil microbial community responses. Four weeks after the initial Cr(VI) application we measured Cr concentration, microbial biomass by fumigation extraction and soil extract ATP, tolerance to Cr and growth rates with tritiated thymidine incorporation, and performed community substrate use analysis with BIOLOG GN plates. Exchangeable Cr(VI) levels were very low, and therefore we assumed the Cr(VI) impact was transient. Microbial biomass was reduced by Cr(VI) addition. Microbial tolerance to Cr(VI) tended to be higher in the Cr-treated rhizosphere soil relative to the non-treated systems, while microorganisms in the Cr-treated bulk soil were less sensitive to Cr(VI) than microorganisms in the non-treated bulk soil. Microbial diversity as measured by population evenness increased with Cr(VI) addition based on a Gini coefficient derived from BIOLOG substrate use patterns. Principal component analysis revealed separation between Cr(VI) treatments, and between rhizosphere and bulk soil treatments. We hypothesize that because of Cr(VI) addition there was indirect selection for fast-growing organisms, alleviation of competition among microbial communities, and increase in Cr tolerance in the rhizosphere due to the faster turnover rates in that environment.

  1. Chromium treatment has no effect in patients with type 2 diabetes in a Western population : a randomized, double-blind, placebo-controlled trial

    NARCIS (Netherlands)

    Kleefstra, N.; Houweling, S.T.; Bakker, S.J.; Gans, R.O.; Meyboom-de Jong, B.; Bilo, H.J.

    2007-01-01

    OBJECTIVE: Chromium treatment has been reported to improve glycemic control in patients with type 2 diabetes. However, concern exists about the possible toxic effects of chromium picolinate. The aim of this study was to determine the effect of chromium treatment in the form of chromium yeast on glyc

  2. Chromium treatment has no effect in patients with type 2 diabetes in a western population - A randomized, double-blind, placebo-controlled trial

    NARCIS (Netherlands)

    Kleefstra, Nanne; Gans, Rijk O. B.; Houweling, Sebastiaan T.; Meyboom-de Jong, Betty; Bakker, Stephan J. L.; Bilo, Henk J. G.; Verhoeven, Simon

    2007-01-01

    OBJECTIVE - Chromium treatment has been reported to improve glycemic control in patients with type 2 diabetes. However, concern exists about the possible toxic effects of chromium picolinate. The aim of this study was to determine the effect of chromium treatment in the form of chromium yeast on gly

  3. Investigation of total and hexavalent chromium in filtered and unfiltered groundwater samples at the Tucson International Airport Superfund Site

    Science.gov (United States)

    Tillman, Fred; McCleskey, R. Blaine; Hermosillo, Edyth

    2016-01-01

    Potential health effects from hexavalent chromium in groundwater have recently become a concern to regulators at the Tucson International Airport Area Superfund site. In 2016, the U.S. Geological Survey sampled 46 wells in the area to characterize the nature and extent of chromium in groundwater, to understand what proportion of total chromium is in the hexavalent state, and to determine if substantial differences are present between filtered and unfiltered chromium concentrations. Results indicate detectable chromium concentrations in all wells, over 75 % of total chromium is in the hexavalent state in a majority of wells, and filtered and unfiltered results differ substantially in only a few high-turbidity total chromium samples.

  4. Retention of chromium by modified Al-Bentonite Retenção de cromo por Al-bentonita modificada

    Directory of Open Access Journals (Sweden)

    C. Volzone

    2002-09-01

    Full Text Available Retention of chromium (III from a tanning wastewater by modified Al-bentonites was studied. One bentonite from San Juan province, Argentina, was used. Al-bentonite was prepared by contact of bentonite with hydrolyzed OH-Al solutions (0.10 M in Al for 24 hours. The modified Al-bentonites were obtained by: a treatment with 0.5 M sodium chloride; b with 0.5 M sodium chloride adjusted at pH 8; and c treatment with an hexametaphosphate solution after sodium addition. Then, the samples were dried at 100 °C and heated at 500 °C. The chromium (III retention by samples was carried out in batch system putting in contact the material with a 2000 ppm Cr tannery waste at different times. The retained chromium was characterized by analyzing the supernatant using UV-visible spectroscopy. The different chromium retention was correlated with structural characteristics of the solids.Foi estudada a retenção de cromo (III de águas residuais por meio de Al-bentonitas modificadas. Foi usada uma bentonita da província de San Juan, Argentina. As bentonitas-Al forma preparadas colocando-as em contato com soluções (0,10 M Al hydrolizadas de OH-Al durante 24 horas. As bentonitas-Al modidicadas foram obtidas por meio de: a tratamento com cloreto de sódio 0,5 M; b com cloreto de sódio 0,5 M sodium com pH ajustado para 8; e c tratamento com uma solução de hexametafosfato após a adição de sódio. As amostras foram então secas a 100 °C e aquecidas a 500 °C. A retenção do cromo (III pelas amostras foi feita em lotes colocando o material em contato em diferentes tempos com um resíduo contendo 2000 ppm de cromo. O cromo retido foi caracterizado por meio de análise do sobrenadante usando espectroscopia UV-visível. As diferentes retenções de cromo foram correlacionadas com características estruturais dos sólidos.

  5. Solid waste removes toxic liquid waste: adsorption of chromium(VI) by iron complexed protein waste.

    Science.gov (United States)

    Fathima, Nishtar Nishad; Aravindhan, Rathinam; Rao, Jonnalagadda Raghava; Nair, Balachandran Unni

    2005-04-15

    The leather processing industry generates huge amounts of wastes, both in solid and liquid form. Fleshing from animal hides/skins is one such waste that is high in protein content. In this study, raw fleshing has been complexed with iron and is used for removal of chromium(VI). The effect of pH and the initial concentration of chromium(VI) on the removal of Cr(IV) by iron treated fleshing is presented. Iron treatment is shown to greatly improve adsorption of the fleshing for hexavalent chromium. The ultimate adsorption capacity of iron treated fleshing is 51 mg of chromium(VI) per gram of fleshing. That of untreated fleshing is 9 mg/g such that iron treatment increases the adsorption capacity of fleshing by 10-fold. The measured adsorption kinetics is well described by a pseudo-second-order kinetic model. The uptake of chromium(VI) by fleshing is best described by the Langmuir adsorption isotherm model. X-ray photoelectron spectroscopic (XPS) studies show that the iron is incorporated into the protein matrix. Shifts in XPS spectra suggest that dichromate binding occurs with iron at active adsorption sites and that iron treated fleshing removes chromium(VI) without reducing it to chromium(III).

  6. Removal of chromium(VI) from aqueous solutions by polymer inclusion membranes.

    Science.gov (United States)

    Kozlowski, Cezary A; Walkowiak, Wladyslaw

    2002-11-01

    The transport through polymer inclusion membranes (PIMs) was found as the effective and selective method of chromium(VI) anions removal from chloride acidic aqueous solutions. The optimal PIMs content was as follows: 41 wt% of cellulose triacetate as the support, 23 wt% of tri-n-octylamine as the ionic carrier, and 36 wt% of o-nitrophenyl pentyl ether as the plasticizer. The results obtained show a linear decrease of permeability coefficient and initial flux values with source phase pH increase. Also linear decrease of initial flux in log-log scale with chromium(VI) concentration increase was observed. Value of slope of this relationship was found to be 0.96 which indicates a first order of chromium(VI) reaction with tri-n-octylamine at membrane/aqueous source interface. Transport of chromium(VI) through PIMs reduces the concentration of chromium(VI) in source aqueous phase from 1.0 to 0.0028 ppm, which is below permissible limit in drinking water in Poland. Competitive transport of chromium(VI), cadmium(II), zinc(II), and iron(III) from acidic aqueous solution across PIMs was found to be efficient for chromium(VI) (99%), and cadmium(II) (99%).

  7. [In vitro percutaneous absorption of chromium powder and the effect of skin cleanser].

    Science.gov (United States)

    D'Agostin, F; Crosera, M; Adami, G; Malvestio, A; Rosani, R; Bovenzi, M; Maina, G; Filon, F Larese

    2007-01-01

    Occupational chromium dermatitis occurs frequently among cement and metal workers, workers dealing with leather tanning and employees in the ceramic industry. The present study, using an in-vitro system, evaluated percutaneous absorption of chromium powder and the effect of rapid skin decontamination with a common detergent. Experiments were performed using the Franz diffusion cell method with human skin. Physiological solution was used as receiving phase and a suspension of chromium powder in synthetic sweat was used as donor phase. The tests were performed without or with decontamination using the cleanser 30 minutes after the start of exposure. The amount of chromium permeated through the skin was analysed by Inductively Coupled Plasma Atomic Emission Spectroscopy and Electro Thermal Atomic Absorption Spectroscopy. Speciation analysis and measurements of chromium skin content were also performed. We calculated a permeation flux of 0.843 +/- 0.25 ng cm(-2) h(-1) and a lag time of 1.1 +/- 0.7 h. The cleaning procedure significantly increased chromium skin content, whereas skin passage was not increased. These results showed that chromium powder can pass through the skin and that skin decontamination did not decrease skin absorption. Therefore, it is necessary to prevent skin contamination when using toxic agents.

  8. Efficiency of Removing Chromium from Plating Industry Wastewater using the Electrocoagulation Method

    Directory of Open Access Journals (Sweden)

    Borghe-ei S.M.1 PhD,

    2015-06-01

    Full Text Available Aims Chromium is one of the most important metallic pollutants in plating industry wastewater. This toxic metal is a serious threat to human health and to the environment due to its cumulative effects and non-degradability. This research intended to study the effects of pH, contact time, and voltage on the degree of chromium removal from wastewater of plating industry by using the electrocoagulation method. Materials & Methods This laboratory research conducted from late May to late November 2012. A 1000cc reactor at laboratory scale was used that included 4 aluminum electrodes of 90% purity, dimensions of 5 by 10cm, and thickness of 1mm, with parallel arrangement. Synthetic chromium-bearing wastewater was prepared at the initial concentration of 50mg/l. The process is done at pH values of 3, 7, and 9, electric potentials of 20, 30, and 40 volts contact durations of 20, 40, 60, and 80 minutes. Findings The degree of chromium reduction did not change linearly with time in the solution and strongly depended on the pH. The efficiency of chromium removal in the samples had an ascending trend with increases in voltage from 20 to 30 and 40 volts. The degree of chromium removal increased at longer contact times. Conclusion Lower pH, more contact time and higher voltages are effective factors in the chromium removal from wastewater by coagulation method.

  9. Chromium in water, suspended particles, sediments and biota in the Iraja River estuary

    Energy Technology Data Exchange (ETDEWEB)

    Pfeiffer, W.C.; Fiszman, M.; de Lacerda, L.D.; van Weerfelt, M.; Carbonell, N.

    1982-11-01

    Analyses of chromium concentrations in waters, suspended particles, bottom sediments, fish (Poecilia reticulata), plants (Paspalum vaginatum, Sesuvium portulacastrum, Philoxeros vermicularis), soils and barnacles (Balanus sp.) were performed from August 1976 to September 1980 in samples collected from the Iraja River and inside its estuary in Guanabara Bay (Rio de Janeiro, Brazil). Sediments and water from the Iraja River showed chromium concentrations of 17536 and 23.39 ppm--a thousand times higher than the published data for freshwater systems. Chromium removed from solution by bottom sediments reaches Guanabara Bay linked to particulate matter. Fish and emergent grass inside the river concentrate chromium from water and/or sediment, returning the metal to the system as detritus. Soil and plants inside the estuary concentrate chromium thirty and ten times higher than in the control area. The vegetal community exhibits a concentration factor smaller than that related to soil and prevents the return of chromium to the estuarine waters. Inside the Guanabara Bay, Balanus sp. appears to be an effective biological monitor as it concentrates chromium in soft tissues 10/sup 3/ times higher than values found in suspended particles (0.012 ..mu..g ml/sup -1/).

  10. High Chromium Tolerant Bacterial Strains from Palar River Basin: Impact of Tannery Pollution

    Directory of Open Access Journals (Sweden)

    K. Sundar

    2010-04-01

    Full Text Available The basic survey study on tanneries and its pollution in the Palar river basin of Vellore District showed that it has been contaminated with heavy metals especially chromium and salts. This study is to improve our understanding to find the Cr contamination level and the ecology of heavy metal tolerance of the native bacterial flora of our study area. Chromium tolerant strains were isolated from contaminated sediments, water and effluents of various tanneries. The minimum and maximum concentration of chromium sediments was in the range of 47.4 and 682.4 mg/L, with an average of 306.285 mg/L in the study area. Sixty-eight chromium resistant bacterial strains were isolated and Maximum Tolerance Concentration (MTC studies have indicated that the tolerance concentrations of the isolates were in the range of 100-3300 mg/L. These bacterial isolates were also checked for their resistance to other heavy metals like Ni, Pb, Zn, Fe and Cd. Eighty percent of the isolates showed resistance to Ni, Pb, Zn, Fe at 100 ppm level and 45% had shown resistance to Cd. The isolates also had shown tolerance to salt (NaCl up to 9%. Significant note was found in the concentration of chromium and in the chromium tolerance ability of the bacteria in the study area and these chromium tolerance bacteria can be used as the indicator for the Cr contamination.

  11. Determination of Chromium(III), Chromium(VI), and Chromium(III) acetylacetonate in water by ion-exchange disk extraction/metal furnace atomic absorption spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Kamakura, Nao, E-mail: minnie04_tb@yahoo.co.jp; Inui, Tetsuo; Kitano, Masaru; Nakamura, Toshihiro

    2014-03-01

    A new method for the separate determination of Chromium(III) (Cr(III)), Chromium(VI) (Cr(VI)), and Cr(III) acetylacetonate (Cr(acac){sub 3}) in water was developed using a cation-exchange extraction disk (CED) and an anion-exchange extraction disk (AED) combined with metal furnace atomic absorption spectrometry (MFAAS). A 100-mL water sample was adjusted to pH 5.6 and passed through the CED placed on the AED. Cr(acac){sub 3} and Cr(III) were adsorbed on the CED, and Cr(VI) was adsorbed on the AED. The adsorbed Cr(acac){sub 3} was eluted with 50 mL of carbon tetrachloride, followed by the elution of Cr(III) with 50 mL of 3 mol L{sup −1} nitric acid. Cr(VI) was eluted with 50 mL of 3 mol L{sup −1} nitric acid. The chemical species of Cr eluted from the CED with carbon tetrachloride was identified as Cr(acac){sub 3} using infrared spectroscopy. The eluate of Cr(acac){sub 3} was diluted to 100 mL with carbon tetrachloride, and those of Cr(III) and Cr(VI) were diluted to 100 mL with deionized water. All of the solutions were subsequently analyzed by MFAAS. The calibration curve for the Cr(acac){sub 3} aqueous solutions exhibited good linearity in the range of 0.1 to 1 ng. The detection limit of Cr, which corresponded to three times the standard deviation (n = 10) of the blank values, was 20 pg. The recovery test for Cr(III), Cr(VI), and Cr(acac){sub 3} exhibited desirable results (96.0%–107%) when 5 μg of each species (50 μg L{sup −1}) was added to 100 mL water samples (i.e., tap water, rainwater, and bottled drinking water). In a humic acid solution, Cr(acac){sub 3} was quantitatively recovered (103%), but Cr(III) and Cr(VI) exhibited poor recoveries (i.e., 84.8% and 78.4%, respectively). - Highlights: • A determination method of Cr(III), Cr(VI), and Cr(III) acetylacetonate in water was developed. • The combination of ion-exchange resin disks with metal furnace AAS was used. • No effect of humic acid on the recovery of Cr(III) acetylacetonate was

  12. Technological progress on detoxification and comprehensive utilization of chromium-containing slag

    Institute of Scientific and Technical Information of China (English)

    柴立元; 何德文; 于霞; 刘恢; 闵小波; 陈为亮

    2002-01-01

    Chromium salt is an important industrial material, but vast waste slag containing chrome(Ⅵ) is brought out in the process of its production. The slag is seriously harmful to environments and human health. The technologies on detoxification and comprehensive utilization of chromium-containing slag were summarized abroad and at home. And various methods were also described for the detoxification mechanism, technology process, and practical application effects in detail. A new concept for detoxification of chromium-containing slag, furthermore, was put forward by using microorganism.

  13. Analysis of Nanometer Structure for Chromium Atoms in Gauss Standing Laser Wave

    Institute of Scientific and Technical Information of China (English)

    ZHANG Wen-Tao; ZHU Bao-Hua; XIONG Xian-Ming

    2010-01-01

    @@ The equation of motion of two-level chromium atoms in Gauss standing laser wave is discussed and the distribution of chromium atoms is given under different transverse velocity conditions.The results show that the focusing position of atoms will be affected by the transverse velocity of atoms.Based on the four-order Runge-Kutta method,the locus of chromium atoms in Gauss standing laser wave is simulated.The three-dimensional characteristics of nanometer structures are stimulated under perfect and emanative conditions.

  14. STUDY ON MORPHOLOGY OF CHROMIUM IN CHILLED Cu-0.14%-2.0%Cr ALLOYS

    Institute of Scientific and Technical Information of China (English)

    H.W.Yang; Z.K.Fan

    2004-01-01

    The morphology of chromium in chilled Cu-Cr alloys with 0.14%-2.0% Cr has been studied. The results showed that eutectic Cr phase takes a fibrous shape, and pre-eutectic Cr is dendritic in the studied chilled Cu-Cr alloy. During solute treatment of the eutectic and super-eutectic Cu-Cr alloys, only part of chromium particles dissolved in copper phase,some fiber and dendritic chromium still remained. Forging before solute treatment can reduce the size of primary Cr particles, which benefits the aging structure.

  15. Peat and coconut fiber as biofilters for chromium adsorption from contaminated wastewaters

    OpenAIRE

    2015-01-01

    Batch adsorption experiments were performed for the removal of chromium (III) and chromium (VI) ions from aqueous solutions using Canadian peat and coconut fiber. The Langmuir model was used to describe the adsorption isotherm. The maximum adsorption for peat reached 18.75 mg/g for Cr(III) and 8.02 mg/g for Cr(VI), whereas the value for fiber was slightly higher and reached 19.21 mg/g for Cr(III) and 9.54 mg/g for Cr(VI). Both chromium forms could be easily eluted from the materials. The adso...

  16. Growth of magnetic cobalt/chromium nano-arrays by atom-optical lithography

    Energy Technology Data Exchange (ETDEWEB)

    Atoneche, F; Malik, D; Kirilyuk, A; Toonen, A J; Etteger, A F van; Rasing, Th, E-mail: f.atoneche@science.ru.nl [Radboud University Nijmegen, Institute for Molecules and Materials, Heyendaalseweg 135, 6525 AJ, Nijmegen (Netherlands)

    2011-07-06

    Arrays of magnetic cobalt/chromium (Co-Cr) nanolines are grown by depositing an atomic beam of Co-Cr alloy through a laser standing wave (SW) at {lambda}/2 = 212.8 nm onto a substrate. During deposition, only the chromium atoms are resonantly affected by the optical potential created by the SW, causing a periodic modulation of the chromium concentration and consequently of the magnetic properties. Magnetic force microscopy and magneto-optical Kerr effect studies reveal a patterned magnetic structure on the substrate surface.

  17. Growth of magnetic cobalt/chromium nano-arrays by atom-optical lithography

    Science.gov (United States)

    Atoneche, F.; Malik, D.; Kirilyuk, A.; Toonen, A. J.; van Etteger, A. F.; Rasing, Th

    2011-07-01

    Arrays of magnetic cobalt/chromium (Co-Cr) nanolines are grown by depositing an atomic beam of Co-Cr alloy through a laser standing wave (SW) at λ/2 = 212.8 nm onto a substrate. During deposition, only the chromium atoms are resonantly affected by the optical potential created by the SW, causing a periodic modulation of the chromium concentration and consequently of the magnetic properties. Magnetic force microscopy and magneto-optical Kerr effect studies reveal a patterned magnetic structure on the substrate surface.

  18. Proposed adsorption-diffusion model for characterizing chromium(VI) removal using dried water hyacinth roots

    Energy Technology Data Exchange (ETDEWEB)

    Sarkar, Debasish; Mukherjee, Paramartha; Bandyopadhyay, Amitava [Department of Chemical Engineering, University of Calcutta, Kolkata (India); Das, Sudip Kumar [Department of Chemical Technology, University of Calcutta, Kolkata (India)

    2010-08-15

    Experiments have been carried out to characterize the adsorption of chromium(VI) in the aqueous phase onto dried roots of water hyacinth. Results revealed a very high degree of removal efficiency ({proportional_to}100%). Theoretical analyzes are also made for describing the sorption and diffusion processes. The effective pore diffusivity of chromium(VI) in the water hyacinth roots is determined by a suitable global optimization technique. The depth of penetration, on the other hand, has been estimated for various initial concentrations of chromium(VI). Theoretically predicted concentration profiles are in excellent agreement with the experimental values. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

  19. Effect of chromium oxide as active site over TiO2-PILC for selective catalytic oxidation of NO.

    Science.gov (United States)

    Zhang, Jingxin; Zhang, Shule; Cai, Wei; Zhong, Qin

    2013-12-01

    This study introduced TiO2-pillared clays (TiO2-PILC) as a support for the catalytic oxidation of NO and analyzed the performance of chromium oxides as the active site of the oxidation process. Cr-based catalysts were prepared by a wet impregnation method. It was found that the 10 wt.% chromium doping on the support achieved the best catalytic activity. At 350 degrees C, the NO conversion was 61% under conditions of GHSV = 23600 hr(-1). The BET data showed that the support particles had a mesoporous structure. H2-TPR showed that Cr(10)TiP (10 wt.% Cr doping on TiO2-PILC) clearly exhibited a smooth single peak. EPR and XPS were used to elucidate the oxidation process. During the NO + O2 adsorption, the intensity of evolution of superoxide ions (O2(-)) increased. The content of Cr3+ on the surface of the used catalyst was 40.37%, but when the used catalyst continued adsorbing NO, the Cr3+ increased to 50.28%. Additionally, O(alpha)/O(beta) increased markedly through the oxidation process. The NO conversion decreased when SO2 was added into the system, but when the SO2 was removed, the catalytic activity recovered almost up to the initial level. FT-IR spectra did not show a distinct characteristic peak of SO4(2-).

  20. Effect of vibration frequency on microstructure and performance of high chromium cast iron prepared by lost foam casting

    Directory of Open Access Journals (Sweden)

    Wen-qi Zou

    2016-07-01

    Full Text Available In the present research, high chromium cast irons (HCCIs were prepared using the lost foam casting (LFC process. To improve the wear resistance of the high chromium cast irons (HCCIs, mechanical vibration was employed during the solidification of the HCCIs. The effects of vibration frequency on the microstructure and performance of the HCCIs under as-cast, as-quenched and as-tempered conditions were investigated. The results indicated that the microstructures of the LFC-produced HCCIs were refined due to the introduction of mechanical vibration, and the hardness was improved compared to that of the alloy without vibration. However, only a slight improvement in hardness was found in spite of the increase of vibration frequency. In contrast, the impact toughness of the as-tempered HCCIs increased with an increase in the vibration frequency. In addition, the wear resistance of the HCCIs was improved as a result of the introduction of vibration and increased with an increase in the vibration frequency.

  1. Absorption of Nickel, Chromium, and Iron by the Root Surface of Primary Molars Covered with Stainless Steel Crowns

    Directory of Open Access Journals (Sweden)

    David Keinan

    2010-01-01

    Full Text Available Objective. The purpose of this study was to analyze the absorption of metal ions released from stainless steel crowns by root surface of primary molars. Study Design. Laboratory research: The study included 34 primary molars, exfoliated or extracted during routine dental treatment. 17 molars were covered with stainless-steel crowns for more than two years and compared to 17 intact primary molars. Chemical content of the mesial or distal root surface, 1 mm apically to the crown or the cemento-enamel junction (CEJ, was analyzed. An energy dispersive X-ray spectrometer (EDS was used for chemical analysis. Results. Higher amounts of nickel, chromium, and iron (5-6 times were found in the cementum of molars covered with stainless-steel crowns compared to intact molars. The differences between groups were highly significant (<.001. Significance. Stainless-steel crowns release nickel, chromium, and iron in oral environment, and the ions are absorbed by the primary molars roots. The additional burden of allergenic metals should be reduced if possible.

  2. Physicochemical and biological quality of soil in hexavalent chromium-contaminated soils as affected by chemical and microbial remediation.

    Science.gov (United States)

    Liao, Yingping; Min, Xiaobo; Yang, Zhihui; Chai, Liyuan; Zhang, Shujuan; Wang, Yangyang

    2014-01-01

    Chemical and microbial methods are the main remediation technologies for chromium-contaminated soil. These technologies have progressed rapidly in recent years; however, there is still a lack of methods for evaluating the chemical and biological quality of soil after different remediation technologies have been applied. In this paper, microbial remediation with indigenous bacteria and chemical remediation with ferrous sulphate were used for the remediation of soils contaminated with Cr(VI) at two levels (80 and 1,276 mg kg(-1)) through a column leaching experiment. After microbial remediation with indigenous bacteria, the average concentration of water-soluble Cr(VI) in the soils was reduced to less than 5.0 mg kg(-1). Soil quality was evaluated based on 11 soil properties and the fuzzy comprehensive assessment method, including fuzzy mathematics and correlative analysis. The chemical fertility quality index was improved by one grade using microbial remediation with indigenous bacteria, and the biological fertility quality index increased by at least a factor of 6. Chemical remediation with ferrous sulphate, however, resulted in lower levels of available phosphorus, dehydrogenase, catalase and polyphenol oxidase. The result showed that microbial remediation with indigenous bacteria was more effective for remedying Cr(VI)-contaminated soils with high pH value than chemical remediation with ferrous sulphate. In addition, the fuzzy comprehensive evaluation method was proven to be a useful tool for monitoring the quality change in chromium-contaminated soils.

  3. Methylene blue photocatalytic mineralization under visible irradiation on TiO2 thin films doped with chromium

    Science.gov (United States)

    Diaz-Uribe, Carlos; Vallejo, William; Ramos, Wilkendry

    2014-11-01

    We studied changes in structural, optical and photocatalytic properties of TiO2 thin films due to doping process with chromium. Powders of undoped TiO2 and chromium-doped TiO2 (Cr:TiO2) were synthesized by sol-gel method and, thin films were deposited by doctor blade method. The properties of the thin films were studied by X-ray diffraction (XRD), infrared spectroscopy (IR) and diffuse reflectance. The XRD patterns indicated that doping process changed the crystalline phases radio of TiO2 thin films, furthermore, the optical analysis showed that band gap value of Cr:TiO2 thin films was 31% fewer than undoped TiO2 thin films. Along, Langmuir-Hinshelwood model was used to obtain kinetic information of the photo-mineralization process; results indicated that photocatalytic activity of Cr:TiO2 thin films were four times better than undoped TiO2 thin films; finally the synergic effect was tested by addition of the H2O2, photocatalytic yield was improved from 26% to 61% when methylene blue photo-mineralization was assisted with slightly amount of H2O2.

  4. Effect of vibration frequency on microstructure and performance of high chromium cast iron prepared by lost foam casting

    Institute of Scientific and Technical Information of China (English)

    Wen-qi Zou; Zhi-guo Zhang; Hao Yang; Wei Li

    2016-01-01

    In the present research, high chromium cast irons (HCCIs) were prepared using the lost foam casting (LFC) process. To improve the wear resistance of the high chromium cast irons (HCCIs), mechanical vibration was employed during the solidiifcation of the HCCIs. The effects of vibration frequency on the microstructure and performance of the HCCIs under as-cast, as-quenched and as-tempered conditions were investigated. The results indicated that the microstructures of the LFC-produced HCCIs were reifned due to the introduction of mechanical vibration, and the hardness was improved compared to that of the aloy without vibration. However, only a slight improvement in hardness was found in spite of the increase of vibration frequency. In contrast, the impact toughness of the as-tempered HCCIs increased with an increase in the vibration frequency. In addition, the wear resistance of the HCCIs was improved as a result of the introduction of vibration and increased with an increase in the vibration frequency.

  5. Photosynthesis performance, antioxidant enzymes, and ultrastructural analyses of rice seedlings under chromium stress.

    Science.gov (United States)

    Ma, Jing; Lv, Chunfang; Xu, Minli; Chen, Guoxiang; Lv, Chuangen; Gao, Zhiping

    2016-01-01

    The present study was conducted to examine the effects of increasing concentrations of chromium (Cr(6+)) (0, 25, 50, 100, and 200 μmol) on rice (Oryza sativa L.) morphological traits, photosynthesis performance, and the activities of antioxidative enzymes. In addition, the ultrastructure of chloroplasts in the leaves of hydroponically cultivated rice (O. sativa L.) seedlings was analyzed. Plant fresh and dry weights, height, root length, and photosynthetic pigments were decreased by Cr-induced toxicity (200 μM), and the growth of rice seedlings was starkly inhibited compared with that of the control. In addition, the decreased maximum quantum yield of primary photochemistry (Fv/Fm) might be ascribed to the decreased the number of active photosystem II reaction centers. These results were confirmed by inhibited photophosphorylation, reduced ATP content and its coupling factor Ca(2+)-ATPase, and decreased Mg(2+)-ATPase activities. Furthermore, overtly increased activities of antioxidative enzymes were observed under Cr(6+) toxicity. Malondialdehyde and the generation rates of superoxide (O2̄) also increased with Cr(6+) concentration, while hydrogen peroxide content first increased at a low Cr(6+) concentration of 25 μM and then decreased. Moreover, transmission electron microscopy showed that Cr(6+) exposure resulted in significant chloroplast damage. Taken together, these findings indicate that high Cr(6+)concentrations stimulate the production of toxic reactive oxygen species and promote lipid peroxidation in plants, causing severe damage to cell membranes, degradation of photosynthetic pigments, and inhibition of photosynthesis.

  6. Hot Corrosion Behavior of High-Chromium, High-Carbon Cast Irons in NaCl-KCl Molten Salts

    Directory of Open Access Journals (Sweden)

    S. Vuelvas-Rayo

    2012-01-01

    Full Text Available A study on the corrosion behavior of a series of experimental high-chromium (18.53–30.48 wt.%, high-carbon (3.82–5.17% cast irons in NaCl-KCl (1 : 1 M at 670°C has been evaluated by using weight loss technique and compared with a 304-type stainless steel. It was found that all castings had a higher corrosion rate than conventional 304SS and that the addition of Cr increased the degradation rate of the cast irons. Additionally, corrosion rate increased by increasing the C contents up to 4.29%, but it decreased with a further increase in its contents. Results are discussed in terms of consumption of the Cr2O3 layer by the melt.

  7. Ultrasound-assisted cloud point extraction for speciation and indirect spectrophotometric determination of chromium(III) and (VI) in water samples

    Science.gov (United States)

    Hashemi, Mahdi; Daryanavard, Seyed Mosayeb

    Ultrasound-assisted cloud point extraction (UACPE) procedure was developed for speciation and indirect spectrophotometric determination of chromium(III) and (VI) in environmental water samples. The method is based on the reduction of Cr(VI) by iodide in acidic media and subsequently formation of I3- anion. The I3- formed can further react with cetyltrimethylammonium bromide (CTAB) and induce its clouding due to formation of an ion-association complex. The formed complex was separated from solution and dissolved in ethanol for spectrophotometric measurement. Cerium(IV) ammonium sulphate was chosen as an oxidizing reagent for pre-oxidation step of Cr(III) to Cr(VI) species before the addition of iodide to the system, up to chromium in trivalent can be determined by the procedure. Experimental parameters for both spectrophotometric reaction and extraction procedure have been optimized. Under optimized conditions Cr(VI) can be determined in the range 20-400 ng mL-1 (R2 = 0.999). Detection limit, preconcentration factor and relative standard deviation were 12 ng mL-1, 20.0 and 2.2% (n = 5), respectively with 10 mL sample volumes. The proposed method has been successfully applied for determination of chromium(V) in spiked water, synthetic seawater and electroplating wastewater samples with average recoveries of 100.1, 99.4 and 99.1%, respectively.

  8. Role of Geitlerinema sp. DE2011 and Scenedesmus sp. DE2009 as Bioindicators and Immobilizers of Chromium in a Contaminated Natural Environment

    Directory of Open Access Journals (Sweden)

    Laia Millach

    2015-01-01

    Full Text Available The aim of this work was to study the potential of the two phototrophic microorganisms, both isolated from Ebro Delta microbial mats, to be used as bioindicators and immobilizers of chromium. The results obtained indicated that (i the Minimum Metal Concentration (MMC significantly affecting Chlorophyll a intensity in Geitlerinema sp. DE2011 and Scenedesmus sp. DE2009 was 0.25 µM and 0.75 µM, respectively, these values being lower than those established by current legislation, and (ii Scenedesmus sp. DE2009 was able to immobilize chromium externally in extracellular polymeric substances (EPS and intracellularly in polyphosphate (PP inclusions. Additionally, this microorganism maintained high viability, including at 500 µM. Based on these results, we postulate that Geitlerinema sp. DE2011 and Scenedesmus sp. DE2009 are good chromium-indicators of cytotoxicity and, further, that Scenedesmus sp. DE2009 plays an important role in immobilizing this metal in a contaminated natural environment.

  9. Stabilisation of nanoscale zero-valent iron with biochar for enhanced transport and in-situ remediation of hexavalent chromium in soil.

    Science.gov (United States)

    Su, Huijie; Fang, Zhanqiang; Tsang, Pokeung Eric; Fang, Jianzhang; Zhao, Dongye

    2016-07-01

    In this study, a biochar-supported nanoscale zero-valent iron (nZVI@BC) material was used for in situ remediation of hexavalent chromium-contaminated soil. Sedimentation tests and column experiments were used to compare the stability and mobility of nZVI@BC and bare-nZVI. The immobilisation efficiency of chromium, toxic effect of chromium and the content of iron were assessed through leaching tests and pot experiments. Sedimentation tests and transport experiments indicated that nZVI@BC with nZVI to BC mass ratio of 1:1 exhibited better stability and mobility than that of bare-nZVI. The immobilisation efficiency of Cr(VI) and Crtotal was 100% and 92.9%, respectively, when the soil was treated with 8 g/kg of nZVI@BC for 15 days. Moreover, such remediation effectively reduced the leachability of Fe caused by bare-nZVI. In addition, pot experiments showed that such remediation reduced the phytotoxicity of Cr and the leachable Fe and was favourable for plant growth.

  10. Electrochemical reduction of hexavalent chromium in ground water

    Energy Technology Data Exchange (ETDEWEB)

    Bansal, S. [Lawrence Livermore National Lab., CA (United States)

    1994-12-01

    Electrochemical reduction of hexavalent chromium (Cr{sup +6}) to its trivalent state (Cr{sup +3}) is showing promising results in treating ground water at Lawrence Livermore National Laboratory`s (LLNL`s) Main Site. An electrolytic cell using stainless-steel and brass electrodes has been found to offer the most efficient reduction while yielding the least amount of precipitate. Trials have successfully lowered concentrations of Cr{sup +6} to below 11 parts per billion (micrograms/liter), the California state standard. We ran several trials to determine optimal voltage for running the cell; each trial consisted of applying a voltage between 6V and 48V for ten minutes through samples obtained at Treatment Facility C(TFC). No conclusive data has been obtained yet.

  11. Fracture and Delamination of Chromium Thin Films on Polymer Substrates

    Science.gov (United States)

    Cordill, M. J.; Taylor, A.; Schalko, J.; Dehm, G.

    2010-04-01

    New emerging technologies in the field of flexible electronic devices require that metal films adhere well and flex with polymer substrates. Common thin film materials used for these applications include copper (Cu) with an adhesion interlayer of chromium (Cr). Copper can be quite ductile and easily move with the polymer substrate. However, Cr is more brittle and fractures at lower strains than Cu. This study aims to examine the fracture and subsequent buckling and delamination of strained Cr films on polyimide (PI). In-situ scanning electron microscope (SEM) straining is used to systematically study the influence of film thickness on fracture and buckling strains. Film fracture and delamination depend on film thickness, and increases in crack and buckle density with decreasing thickness are explored by a shear lag model.

  12. Hexavalent Chromium Removal by Litchi chinensis Sonn Peel

    Directory of Open Access Journals (Sweden)

    Ismael Acosta-Rodriguez

    2012-01-01

    Full Text Available Problem statement: We studied the Chromium (VI removal capacity in aqueous solution by the litchi peel. Approach: We use the diphenylcarbazide method to evaluate the metal concentration. Results: The highest biosorption of the metal (50 mg L-1 occurs within 6 min, at pH of 1 and 28°C. According to temperature, the highest removal was observed at 40 and 50°C, in 45 min, when the metal (1 g L-1 was completely adsorbed. At the analyzed concentrations of Cr (VI, litchi peel, showed excellent removal capacity, besides it removes efficiently the metal in situ (100% removal, 5 days of incubation, 5 and 10 g of biomass. After 1 h of incubation the studied biomass reduces 1.0 g of Cr (VI with the simultaneous production of Cr (III. Conclusion: The shell can be used to eliminate it from industrial wastewater."

  13. Investigation of hexavalent chromium sorption in serpentine sediments

    Science.gov (United States)

    Mpouras, Thanasis; Chrysochoou, Maria; Dermatas, Dimitris

    2017-02-01

    In this study the removal of hexavalent chromium (Cr6 +) by serpentine sediments was investigated in order to delineate Cr6 + sorption behavior in aquifers with ultramafic geologic background. Batch experiments were conducted in order to determine the influence of several parameters on Cr6 + removal, including the pH of the sediment solution, mineralogy, sediment's particle size and Cr6 + initial concentration. The results showed that Cr6 + removal was due to both adsorption and reduction phenomena. Reduction was attributed to the presence of a magnetic fraction in the sediment, mostly related to magnetite, which contributed almost 50% of the total removal in the pH range 3-7. Adsorption behavior was dominated by the finer sediment fraction (d transport modeling.

  14. Polyaniline coating with various substrates for hexavalent chromium removal

    Science.gov (United States)

    Qiu, Bin; Xu, Cuixia; Sun, Dezhi; Wang, Qiang; Gu, Hongbo; Zhang, Xin; Weeks, Brandon L.; Hopper, Jack; Ho, Thomas C.; Guo, Zhanhu; Wei, Suying

    2015-04-01

    Hexavalent chromium (Cr(VI)) contamination is increasingly serious in surface water and groundwater, therefore, its removal attracts increasing attention due to its highly toxic to human health. The cost effective and sustainable adsorbents are urgently needed for the remediation of Cr(VI) pollution. Polyanline (PANI), a conductive polymer, has demonstrated a great performance on Cr(VI) removal. But the recycling is the challenge for its application due to its small size. The PANI coating with various substrates is an effective approach to solve this problem. The synthesis methods and applications of the PANI coated magnetic Fe3O4, carbon fabric and cellulose composites for the Cr(VI) removal were reviewed. Finally, this review analyzed the Cr(VI) removal mechanisms by the PANI composites considering the substrate and the PANI coating.

  15. Chromium Renderserver: scalable and open remote rendering infrastructure.

    Science.gov (United States)

    Paul, Brian; Ahern, Sean; Bethel, E Wes; Brugger, Eric; Cook, Rich; Daniel, Jamison; Lewis, Ken; Owen, Jens; Southard, Dale

    2008-01-01

    Chromium Renderserver (CRRS) is software infrastructure that provides the ability for one or more users to run and view image output from unmodified, interactive OpenGL and X11 applications on a remote, parallel computational platform equipped with graphics hardware accelerators via industry-standard Layer 7 network protocols and client viewers. The new contributions of this work include a solution to the problem of synchronizing X11 and OpenGL command streams, remote delivery of parallel hardware accelerated rendering, and a performance analysis of several different optimizations that are generally applicable to a variety of rendering architectures. CRRS is fully operational, Open Source software. imagery and sending it to a remote viewer.

  16. Tuning ferromagnetism in zinc oxide nanoparticles by chromium doping

    Science.gov (United States)

    Kaur, Palvinder; Pandey, S. K.; Kumar, Sanjeev; Negi, N. S.; Chen, C. L.; Rao, S. M.; Wu, M. K.

    2015-11-01

    Zn1- x Cr x O nanoparticles with x = 0.0, 0.01, 0.03 and 0.05 were synthesized by the sol-gel technique. Powder X-ray diffraction (XRD) studies reveal that chromium (Cr) incorporates into the ZnO crystal lattice without disturbing the parent hexagonal (wurtzite) structure. Transmission electron microscopy (TEM) measurements show that the average size of these nanoparticles is in the range 15-25 nm. Optical absorption studies show that the band gap of ZnO nanoparticles varies with Cr doping. Photoluminescence (PL) studies depict the presence of defects in Cr-doped nanoparticles. Undoped ZnO exhibits diamagnetic behavior while Cr-doped ZnO samples exhibit weak ferromagnetism to anti-ferromagnetism depending on the Cr content.

  17. Nanotwin hardening in a cubic chromium oxide thin film

    Directory of Open Access Journals (Sweden)

    Kazuma Suzuki

    2015-09-01

    Full Text Available NaCl-type (B1 chromium oxide (CrO has been expected to have a high hardness value and does not exist as an equilibrium phase. We report a B1-based Cr0.67O thin film with a thickness of 144 nm prepared by pulsed laser deposition as an epitaxial thin film on a MgO single crystal. The thin film contained a number of stacking faults and had a nanotwinned structure composed of B1 with disordered vacancies and corundum structures. The Cr0.67O thin film had a high indentation hardness value of 44 GPa, making it the hardest oxide thin film reported to date.

  18. Identification Trial of Crystallization Parameters of Modified Chromium Cast Iron

    Directory of Open Access Journals (Sweden)

    A. Studnicki

    2007-07-01

    Full Text Available In the paper results of researches of abrasion-resisting chromium cast iron inoculated with boron carbide B4C primary crystallization are presented. The main aim of work was make an attempt to identification of crystallization parameters that changed in reason of inoculation. Essential primary crystallization parameters, with the help of which, will be possible to evaluate the inoculation capacity were searched. It was found that in the result of inoculant actions characteristic temperatures were changed and time of primary crystallization was decreased. For tests the new broadened Derivative Thermal Analysis method, in which three samples with different solidification module were applied, was used. Thanks to this inoculation capacity in casts with significant diversified self-cooling ranges was possible to observe.

  19. Tetravalent chromium doped laser materials and NIR tunable lasers

    Science.gov (United States)

    Alfano, Robert R. (Inventor); Petricevic, Vladimir (Inventor); Bykov, Alexey (Inventor)

    2008-01-01

    A method is described to improve and produce purer Cr.sup.4+-doped laser materials and lasers with reduced co-incorporation of chromium in any other valence states, such as Cr.sup.3+, Cr.sup.2+, Cr.sup.5+, and Cr.sup.6+. The method includes: 1) certain crystals of olivine structure with large cation (Ca) in octahedral sites such as Cr.sup.4+:Ca.sub.2GeO.sub.4, Cr.sup.4+:Ca.sub.2SiO.sub.4, Cr.sup.4+:Ca.sub.2Ge.sub.xSi.sub.1-xO.sub.4 (where 0NIR laser applications.

  20. Semisolid Slurry Preparation of Die Steel with High Chromium Content

    Institute of Scientific and Technical Information of China (English)

    MAO Wei-min; ZHAO Ai-min; ZHANG Li-juan; ZHONG Xue-you

    2004-01-01

    The semisolid slurry preparation of die steels Cr12 and Cr12MoV with high chromium content was studied. The results show that the semisolid slurry of both steels with solid of 40 %-60 % can be made by electromagnetic stirring method and is easy to be discharged from the bottom little hole of the stirring chamber. The sizes of the spherical primary austenite in the slurry of die steels Cr12 and Cr12MoV are 50-100 μm and 80-150 μm, respectively. The homogeneous temperature field and solute field for both steel melts are obtained. The strong temperature fluctuation in the melt with many fine primary austenite grains occurs and the remelting of the secondary arm roots at the same time is accelerated because of the electromagnetic stirring. These are the most important reasons for deposition of spherical primary austenite grains.

  1. Characterization of electrocoagulation for removal of chromium and arsenic

    Energy Technology Data Exchange (ETDEWEB)

    Parga, J.R.; Valverde, V. [Institute of Technology of Saltillo, Dept. of Metallurgy and Materials Science, V. Carranza 2400, Saltillo Coah., C.P. 25280 (Mexico); Cocke, D.L.; Gomes, J.A.G.; Kesmez, M.; Moreno, H. [Lamar University, Gill Chair of Chemistry and Chemical Engineering, Beaumont, TX 77710 (United States); Weir, M.; Mencer, D. [Wilkes University, Dept. of Chemistry, Wilkes-Barre, PA 18766 (United States)

    2005-05-01

    Protection of the global environment and, in particular, providing a sustainable source of clean water is a necessity for human survival. The wide use of heavy metals by modern industries has generated by-products containing heavy metals. Specifically, large quantities of chromium and arsenic containing compounds are being discharged into the environment. This study has been conducted to determine the feasibility of an electrocoagulation (EC) process using air injection to remove these inorganic elements with iron electrodes. Powder X-ray diffraction, scanning electron microscopy, and transmission Moessbauer spectroscopy were used to characterize the solid products formed at iron electrodes during EC. The results of this study suggest that magnetite particles and amorphous iron oxyhydroxides are present in the examined EC products. The field pilot-scale study demonstrated the removal of Cr(VI)/Cr(III) and As(III)/As(V) with an efficiency of more than 99 % from both wastewater and wells. (Abstract Copyright [2005], Wiley Periodicals, Inc.)

  2. Adsorption of hexavalent chromium by graphite–chitosan binary composite

    Indian Academy of Sciences (India)

    RAJENDRA S DONGRE

    2016-06-01

    Graphite chitosan binary (GCB) composite was prepared for hexavalent chromium adsorption from studied water. GCB was characterized by TGA, FTIR, SEM and X-ray diffraction techniques.Wide porous sorptive surface of 3.89 m$^2$ g$^{−1}$ and absorptive functionalities of GCB was due to 20% (w/w) graphite support on chitosan evidenced from FTIR and SEM that impart maximum adsorption at pH 4, agitation with 200 rpm for 180 min. Adsorption studies revealed intraparticle diffusion models and best-fitted kinetics was pseudo 2nd order one. A wellfitted Langmuir isotherm model suggested monolayer adsorption with an adsorption capacity ($q_m$) of 105.6 mg g$^{−1}$ and $R^2 = 0.945$. Sorption mechanisms based on metal ionic interactions, intrusion/diffusion and chemisorptions onto composite. This graphite chitosan binary composite improve sorbent capacity for Cr(VI).

  3. Microbial reduction of hexavalent chromium by landfill leachate.

    Science.gov (United States)

    Li, Yarong; Low, Gary K-C; Scott, Jason A; Amal, Rose

    2007-04-02

    The reduction of hexavalent chromium (Cr(VI)) in municipal landfill leachates (MLL) and a non-putrescible landfill leachate (NPLL) was investigated. Complete Cr(VI) reduction was achieved within 17 days in a MLL when spiked with 100 mg l(-1) Cr(VI) or less. In the same period, negligible Cr(VI) reduction was observed in NPLL. In MLL, Cr(VI) reduction was demonstrated to be a function of initial Cr(VI) concentration and bacterial biomass and organic matter concentrations. The bacteria were observed to tolerate 250 mg l(-1) Cr(VI) in MLL and had an optimal growth activity at pH 7.4 in a growth medium. The MLL also possessed an ability to sequentially reduce Cr(VI) over three consecutive spiking cycles.

  4. Chromium as resonant donor impurity in PbTe

    Science.gov (United States)

    Nielsen, M. D.; Levin, E. M.; Jaworski, C. M.; Schmidt-Rohr, K.; Heremans, J. P.

    2012-01-01

    We synthesize and perform structural, thermoelectric, magnetic, and 125Te NMR characterization measurements on chromium-doped PbTe. 125Te NMR and magnetic measurements show that Pb1-xCrxTe is a solid solution up to x = 0.4 at.% and forms an n-type dilute paramagnetic semiconductor. The Cr level is resonant and pins the Fermi level about 100 meV into the conduction band at liquid nitrogen temperatures and below, but it moves into the gap as the temperature increases to 300 K. 125Te NMR spectra exhibit a Knight shift that correlates well with Hall effect measurements and resolve peaks of Te near Cr. Magnetic behavior indicates that Cr exists mainly as Cr2+. No departure from the Pisarenko relation for PbTe is observed. Secondary Cr2Te3 and Cr3+δTe4 phases are present in samples with x > 0.4%.

  5. Chromium as Resonant Donor Impurity in PbTe

    Energy Technology Data Exchange (ETDEWEB)

    Nielsen, M.D.; Levin, Evgenii; Jaworski, C.M.; Schmidt-Rohr, Klaus; Heremans, J.P.

    2012-01-25

    We synthesize and perform structural, thermoelectric, magnetic, and 125Te NMR characterization measurements on chromium-doped PbTe. 125Te NMR and magnetic measurements show that Pb1−xCrxTe is a solid solution up to x = 0.4 at.% and forms an n-type dilute paramagnetic semiconductor. The Cr level is resonant and pins the Fermi level about 100 meV into the conduction band at liquid nitrogen temperatures and below, but it moves into the gap as the temperature increases to 300 K. 125Te NMR spectra exhibit a Knight shift that correlates well with Hall effect measurements and resolve peaks of Te near Cr. Magnetic behavior indicates that Cr exists mainly as Cr2+. No departure from the Pisarenko relation for PbTe is observed. Secondary Cr2Te3 and Cr3+δTe4 phases are present in samples with x > 0.4%.

  6. Stepwise construction of manganese-chromium carbonyl chalcogenide complexes: synthesis, electrochemical properties, and computational studies.

    Science.gov (United States)

    Shieh, Minghuey; Miu, Chia-Yeh; Huang, Kuo-Chih; Lee, Chung-Feng; Chen, Bao-Gun

    2011-08-15

    When trigonal-bipyramidal clusters, [PPN][E(2)Mn(3)(CO)(9)] (E = S, Se), were treated with Cr(CO)(6) and PPNCl in a molar ratio of 1:1:2 or 1:2:2 in 4 M KOH/MeCN/MeOH solutions, mono-Cr(CO)(5)-incorporated HE(2)Mn(3)-complexes [PPN](2)[HE(2)Mn(3)Cr(CO)(14)] (E = S, [PPN](2)[1a]; Se, [PPN](2)[1b]), respectively, were formed. X-ray crystallographic analysis showed that 1a and 1b were isostructural and each displayed an E(2)Mn(3) square-pyramidal core with one of the two basal E atoms externally coordinated with one Cr(CO)(5) group and one Mn-Mn bond bridged by one hydrogen atom. However, when the TMBA(+) salts for [E(2)Mn(3)(CO)(9)](-) were mixed with Cr(CO)(6) in a molar ratio of 1:1 in 4 M KOH/MeOH solutions and refluxed at 60 °C, mono-Cr(CO)(3)-incorporated E(2)Mn(3)Cr octahedral clusters [TMBA](3)[E(2)Mn(3)Cr(CO)(12)] (E = S, [TMBA](3)[2a]; Se, [TMBA](3)[2b]), respectively, were obtained. Clusters 2a and 2b were isostructural, and each consisted of an octahedral E(2)Mn(3)Cr core, in which each Mn-Mn or Mn-Cr bond of the Mn(3)Cr plane was semibridged by one carbonyl ligand. Clusters 1a and 1b (with [TMBA] salts) underwent metal core closure to form octahedral clusters 2a and 2b upon treatment with KOH/MeOH at 60 °C. In addition, 1a and 1b were found to undergo cluster expansion to form di-Cr(CO)(5)-incorporated HE(2)Mn(3)-clusters [HE(2)Mn(3)Cr(2)(CO)(19)](2-) (E = S, 3a; Se, 3b), respectively, upon the addition of 1 or 2 equiv of Cr(CO)(6) heated in refluxing CH(2)Cl(2). Clusters 3a and 3b were structurally related to clusters 1a and 1b, but with the other bare E atom (E = S, 3a; Se, 3b) further externally coordinated with one Cr(CO)(5) group. The nature, cluster transformation, and electrochemical properties of the mixed manganese-chromium carbonyl sulfides and selenides were systematically discussed in terms of the chalcogen elements, the introduced chromium carbonyl group, and the metal skeleton with the aid of molecular calculations at the BP86 level of the

  7. N-acetylcysteine attenuates hexavalent chromium-induced hypersensitivity through inhibition of cell death, ROS-related signaling and cytokine expression.

    Directory of Open Access Journals (Sweden)

    Yu-Hsuan Lee

    Full Text Available Chromium hypersensitivity (chromium-induced allergic contact dermatitis is an important issue in occupational skin disease. Hexavalent chromium (Cr (VI can activate the Akt, Nuclear factor κB (NF-κB, and Mitogen-activated protein kinase (MAPK pathways and induce cell death, via the effects of reactive oxygen species (ROS. Recently, cell death stimuli have been proposed to regulate the release of inflammatory cytokines, such as tumor necrosis factor-α (TNF-α and interleukin-1 (IL-1. However, the exact effects of ROS on the signaling molecules and cytotoxicity involved in Cr(VI-induced hypersensitivity have not yet been fully demonstrated. N-acetylcysteine (NAC could increase glutathione levels in the skin and act as an antioxidant. In this study, we investigated the effects of NAC on attenuating the Cr(VI-triggered ROS signaling in both normal keratinocyte cells (HaCaT cells and a guinea pig (GP model. The results showed the induction of apoptosis, autophagy and ROS were observed after different concentrations of Cr(VI treatment. HaCaT cells pretreated with NAC exhibited a decrease in apoptosis and autophagy, which could affect cell viability. In addition, Cr (VI activated the Akt, NF-κB and MAPK pathways thereby increasing IL-1α and TNF-α production. However, all of these stimulation phenomena could be inhibited by NAC in both of in vitro and in vivo studies. These novel findings indicate that NAC may prevent the development of chromium hypersensitivity by inhibiting of ROS-induced cell death and cytokine expression.

  8. The protective and toxic effects of rhubarb tannins and anthraquinones in treating hexavalent chromium-injured rats: the Yin/Yang actions of rhubarb.

    Science.gov (United States)

    Zeng, Ling-na; Ma, Zhi-jie; Zhao, Yan-ling; Zhang, Lin-dong; Li, Rui-sheng; Wang, Jia-bo; Zhang, Ping; Yan, Dan; Li, Qi; Jiang, Bing-qian; Pu, Shi-biao; Lü, Yang; Xiao, Xiao-he

    2013-02-15

    Chromium nephrotoxicity (CrNT) is thought to occur through the oxidant lesion mechanism. There is still a lack of specific remedies against CrNT. We primarily screened Chinese herbal medicines with a potential protective effect against CrNT, e.g., rhubarb (Rheum palmatum L.). However, the active constituents in rhubarb and its mechanisms remain unclear. In this study, the total rhubarb extract (TR) was successively separated into three parts: total anthraquinone extract (TA), total tannin extract (TT) and remaining component extract (RC). The effects of each extract on the potassium dichromate (K(2)Cr(2)O(7))-induced nephrotoxicity in rats were comparatively assessed. The results showed that only the administration of TT protected the kidney function in K(2)Cr(2)O(7)-injured rats. Besides, TT showed significant activity to scavenge hydroxyl radicals, which is considered to be the dominant lesion product generated by hexavalent chromium. TT also showed a reduced ability to transform toxic high valence chromium ions into non-toxic low valence ions. And TT was able to further precipitate chromium ions. These results suggested that rhubarb tannins treat CrNT as a free radical scavenger, reductant, and metal precipitant. The multiple protective routes of the plant tannins reveal a superior option for development into a promising natural remedy against CrNT. In addition, the opposite effects of rhubarb anthraquinones in treating CrNT were observed compared to rhubarb tannins, which suggested the duo-directional effects (Yin and Yang) of herbal medicines should be addressed.

  9. Effect of Chromium on Corrosion Behavior of P110 Steels in CO2-H2S Environment with High Pressure and High Temperature

    Directory of Open Access Journals (Sweden)

    Jianbo Sun

    2016-03-01

    Full Text Available The novel Cr-containing low alloy steels have exhibited good corrosion resistance in CO2 environment, mainly owing to the formation of Cr-enriched corrosion film. In order to evaluate whether it is applicable to the CO2 and H2S coexistence conditions, the corrosion behavior of low-chromium steels in CO2-H2S environment with high pressure and high temperature was investigated using weight loss measurement and surface characterization. The results showed that P110 steel suffered localized corrosion and both 3Cr-P110 and 5Cr-P110 steels exhibited general corrosion. However, the corrosion rate of 5Cr-P110 was the highest among them. The corrosion process of the steels was simultaneously governed by CO2 and H2S. The outer scales on the three steels mainly consisted of FeS1−x crystals, whereas the inner scales on Cr-containing steels comprised of amorphous FeS1−x, Cr(OH3 and FeCO3, in contrast with the amorphous FeS1−x and FeCO3 mixture film of P110 steel. The more chromium the steel contains, the more chromium compounds the corrosion products contain. The addition of chromium in steels increases the uniformity of the Cr-enriched corrosion scales, eliminates the localized corrosion, but cannot decrease the general corrosion rates. The formation of FeS1−x may interfere with Cr-enriched corrosion scales and lowering the corrosion performance of 3Cr-P110 and 5Cr-P110 steels.

  10. Ab initio calculation of chromium oxide containing Ti dopant

    Energy Technology Data Exchange (ETDEWEB)

    Maldonado, Frank [Grupo de Fisicoquimica de Materiales, Universidad Tecnica Particular de Loja, Apartado 11-01-608, Loja (Ecuador); Novillo, Corina [Escuela de Ingenieria Quimica, Universidad Tecnica Particular de Loja, Apartado 11-01-608, Loja (Ecuador); Stashans, Arvids, E-mail: arvids@utpl.edu.ec [Grupo de Fisicoquimica de Materiales, Universidad Tecnica Particular de Loja, Apartado 11-01-608, Loja (Ecuador)

    2012-01-17

    Highlights: Black-Right-Pointing-Pointer Microstructure changes in chromium oxide due to the Ti doping. Black-Right-Pointing-Pointer Discovery of magnetism in Ti-doped {alpha}-Cr{sub 2}O{sub 3} crystal. Black-Right-Pointing-Pointer Explanation of the origin of n-type electrical conductivity. Black-Right-Pointing-Pointer Detailed analysis of electronic properties and density of states. Black-Right-Pointing-Pointer As to authors' knowledge, Ti-doped crystal is studied for the first time by the DFT. - Abstract: First-principles computations based on the density functional theory within the generalised gradient approximation and introduced intra-atomic interaction term for strongly correlated electrons (DFT + U method) has been used in this work. Ti impurity doping in the {alpha}-Cr{sub 2}O{sub 3} crystal has been carried out considering single defect model within the periodic crystalline structure. Atomic displacements, Bader charges on atoms have been computed showing that Ti dopant converts the chemical bonding in its neighbourhood into more ionic one. The defect-local microstructure is such as there exist general tendency of atomic rearrangements away with respect to the Ti imperfection. It is found that defect incorporation produces some local changes upon the band structure of the material and also induces a metallic state. That implies n-type electrical conductivity in the Ti-doped {alpha}-Cr{sub 2}O{sub 3} crystals and relates our work directly to a number of experimental studies in this area. Our results provide evidence over change in magnetic moments in the vicinity of defect, which means that the chromium oxide doped with Ti impurity might not act as an antiferromagnetic substance.

  11. Fluctuations in Precambrian atmospheric oxygenation recorded by chromium isotopes

    Science.gov (United States)

    Frei, Robert; Gaucher, Claudio; Poulton, Simon W.; Canfield, Don E.

    2009-09-01

    Geochemical data suggest that oxygenation of the Earth's atmosphere occurred in two broad steps. The first rise in atmospheric oxygen is thought to have occurred between ~2.45 and 2.2Gyr ago, leading to a significant increase in atmospheric oxygen concentrations and concomitant oxygenation of the shallow surface ocean. The second increase in atmospheric oxygen appears to have taken place in distinct stages during the late Neoproterozoic era (~800-542Myr ago), ultimately leading to oxygenation of the deep ocean ~580Myr ago, but details of the evolution of atmospheric oxygenation remain uncertain. Here we use chromium (Cr) stable isotopes from banded iron formations (BIFs) to track the presence of Cr(VI) in Precambrian oceans, providing a time-resolved picture of the oxygenation history of the Earth's atmosphere-hydrosphere system. The geochemical behaviour of Cr is highly sensitive to the redox state of the surface environment because oxidative weathering processes produce the oxidized hexavalent [Cr(VI)] form. Oxidation of reduced trivalent [Cr(III)] chromium on land is accompanied by an isotopic fractionation, leading to enrichment of the mobile hexavalent form in the heavier isotope. Our fractionated Cr isotope data indicate the accumulation of Cr(VI) in ocean surface waters ~2.8 to 2.6Gyr ago and a likely transient elevation in atmospheric and surface ocean oxygenation before the first great rise of oxygen 2.45-2.2Gyr ago (the Great Oxidation Event). In ~1.88-Gyr-old BIFs we find that Cr isotopes are not fractionated, indicating a decline in atmospheric oxygen. Our findings suggest that the Great Oxidation Event did not lead to a unidirectional stepwise increase in atmospheric oxygen. In the late Neoproterozoic, we observe strong positive fractionations in Cr isotopes (δ53Cr up to +4.9‰), providing independent support for increased surface oxygenation at that time, which may have stimulated rapid evolution of macroscopic multicellular life.

  12. Probing neutrino nature at Borexino detector with chromium neutrino source

    Energy Technology Data Exchange (ETDEWEB)

    Sobkow, W.; Blaut, A. [University of Wroclaw, Institute of Theoretical Physics, Wroclaw (Poland)

    2016-10-15

    In this paper, we indicate a possibility of utilizing the intense chromium source (∝370 PBq) in probing the neutrino nature in low energy neutrino experiments with the ultra-low threshold and background real-time Borexino detector located near the source (∝8 m). We analyse the elastic scattering of electron neutrinos (Dirac or Majorana, respectively) on the unpolarised electrons in the relativistic neutrino limit. We assume that the incoming neutrino beam is the superposition of left-right chiral states produced by the chromium source. Left chiral neutrinos may be detected by the standard V - A and non-standard scalar S{sub L}, pseudoscalar P{sub L}, tensor T{sub L} interactions, while right chiral ones partake only in the exotic V + A and S{sub R}, P{sub R}, T{sub R} interactions. Our model-independent study is carried out for the flavour (current) neutrino eigenstates. We compute the expected event number for the standard V - A interaction of the left chiral neutrinos using the current experimental values of standard couplings and in the case of left-right chiral superposition. We show that the significant decrement in the event number due to the interference terms between the standard and exotic interactions for the Majorana neutrinos may appear. We also demonstrate how the presence of the exotic couplings affects the energy spectrum of outgoing electrons, both for the Dirac and Majorana cases. The 90 % C.L. sensitivity contours in the planes of corresponding exotic couplings are found. The presence of interferences in the Majorana case gives the stronger constraints than for the Dirac neutrinos, even if the neutrino source is placed outside the detector. (orig.)

  13. High-valent imido complexes of manganese and chromium corroles.

    Science.gov (United States)

    Edwards, Nicola Y; Eikey, Rebecca A; Loring, Megan I; Abu-Omar, Mahdi M

    2005-05-16

    The oxidation reaction of M(tpfc) [M = Mn or Cr and tpfc = tris(pentafluorophenyl)corrole] with aryl azides under photolytic or thermal conditions gives the first examples of mononuclear imido complexes of manganese(V) and chromium(V). These complexes have been characterized by NMR, mass spectrometry, UV-vis, EPR, elemental analysis, and cyclic voltammetry. Two X-ray structures have been obtained for Mn(tpfc)(NMes) and Cr(tpfc)(NMes) [Mes = 2,4,6-(CH(3))(3)C(6)H(2)]. Short metal-imido bonds (1.610 and 1.635 Angstroms) as well as nearly linear M-N-C angles are consistent with triple M triple-bond NR bond formation. The kinetics of nitrene [NR] group transfer from manganese(V) corroles to various organic phosphines have been defined. Reduction of the manganese(V) corrolato complex affords phosphine imine and Mn(III) with reaction rates that are sensitive to steric and electronic elements of the phosphine substrate. An analogous manganese complex with a variant corrole ligand containing bromine atoms in the beta-pyrrole positions, Mn(Br(8)tpfc)(NAr), has been prepared and studied. Its reaction with PEt(3) is 250x faster than that of the parent tpfc complex, and its Mn(V/IV) couple is shifted by 370 mV to a more positive potential. The EPR spectra of chromium(V) imido corroles reveal a rich signal at ambient temperature consistent with Cr(V) triple-bond NR (d(1), S = 1/2) containing a localized spin density in the d(xy) orbital, and an anisotropic signal at liquid nitrogen temperature. Our results demonstrate the synthetic utility of organic aryl azides in the preparation of mononuclear metal imido complexes previously considered elusive, and suggest strong sigma-donation as the underlying factor in stabilizing high-valent metals by corrole ligands.

  14. 40 CFR 749.68 - Hexavalent chromium-based water treatment chemicals in cooling systems.

    Science.gov (United States)

    2010-07-01

    ... proprietorship, association, or any other business entity; any State or political subdivision thereof; any municipality; any interstate body; and any department, agency, or instrumentality of the Federal Government... the following language: WARNING: This product contains hexavalent chromium. Inhalation of...

  15. Methods to Develop Inhalation Cancer Risk Estimates for Chromium and Nickel Compounds

    Science.gov (United States)

    This document summarizes the approaches and rationale for the technical and scientific considerations used to derive inhalation cancer risks for emissions of chromium and nickel compounds from electric utility steam generating units.

  16. Preconcentration and Determination of Chromium Species Using Octadecyl Silica Membrane Disks and Flame Atomic Absorption Spectrometry

    Institute of Scientific and Technical Information of China (English)

    MOGHIMI Ali; SABER-TEHRANI Mohammad; WAQIF-HUSAIN Syed; MOHAMMADHOSSEINI Majid

    2007-01-01

    A novel and selective method for the fast determination of trace amounts of chromium species in water samples has been developed.The procedure is based on the selective formation of chromium diethyldithiocarbamate complexes at different pH in the presence of Mn(Ⅱ) as an enhancement agent of chromium signals followed by elutionwith organic eluents and determination by atomic flame absorption spectrometry.The maximum capacity of the employed disks was found to be (3964±3) μg and (376±2) μg for Cr(Ⅲ) and Cr(Ⅵ),respectively.The detection limit of the proposed method is 49 and 43 ng·L-1 for Cr(Ⅲ) and Cr(Ⅵ),respectively.The proposed method was successfully applied for determination of chromium species Cr(Ⅲ) and Cr(Ⅵ) in different water samples.

  17. EXPERIMENTAL INVESTIGATION ON CHROMIUM(VI REMOVAL FROM AQUEOUS SOLUTION USING ACTIVATED CARBON RESORCINOL FORMALDEHYDE XEROGELS

    Directory of Open Access Journals (Sweden)

    Eghe A. Oyedoh

    2016-10-01

    Full Text Available The adsorption of chromium(VI metal ion in aqueous solutions by activated carbon resorcinol formaldehyde xerogels (ACRF was investigated. The results showed that pore structure, surface area and the adsorbent surface chemistry are important factors in the control of the adsorption of chromium(VI metal ions. The isotherm parameters were obtained from plots of the isotherms and from the application of Langmuir and Freundlich Isotherms. Based on regression analysis, the Langmuir isotherm model was the best fit. The maximum adsorption capacity of ACRF for chromium (VI was 241.9 mg/g. The pseudo-second-order kinetic model was the best fit to the experimental data for the adsorption of chromium metal ions by activated carbon resorcinol formaldehyde xerogels. The thermodynamics of Cr(VI ions adsorption onto ACRF was a spontaneous and endothermic process.

  18. Remediation of Nitrate and ChromiumContaminated Groundwater by Zero-valent IronPRB

    Institute of Scientific and Technical Information of China (English)

    2015-01-01

    Through continuous flow experimentation, the reactivity characteristics of zero-valent iron (Fe0)-PRB with ground watercontaminated by nitrate, chromium and the combination of nitrate and chromium were investigated. The results showed thatnitrate could be effectively deoxidized by zero-valent iron. NO2- -N was the transitional deoxidization product, while NH4+-Nwas the main final product in the effluent. Chromium could be deoxidized by zero-valent iron more effectively for the chromiumcontaminated ground water which was treated by PRB. The redox products such as Fe3+ and Cr(III) precipitated on the packingmedia during the process. For the treatment of ground water contaminated by both nitrate and chromium, the results showed thatthe Cr(VI) removal efficiency by the zero-valent iron was not affected by the co-existence of NO3- -N, while the NO3- -N removalefficiency decreased with the existence of Cr(VI).

  19. THE INVESTIGATION ON PLASMA ARC TREATMENT OF CHROMIUM PLATED ALLOY STRUCTURE STEEL

    Institute of Scientific and Technical Information of China (English)

    X.M. Fan; J.W. Huang; K.H. Wang; Q. Liu

    2005-01-01

    The technology of plasma arc was used to modify the interface adhesion between chromium coating and steel substrate. The interface microstructure was studied as a function of plasma arc processing parameters. Microstructure analysis was performed by optical microscopy,scanning electron microscopy and electron probe. The microhardness distribution along the depth of a cross-section of the chromium coating and the substrate was measured. The results show the energy density of transferred plasma arc is obviously higher than plasma non-transferred arc. The molten interface was obtained by plasma transferred arc. Interfaces between chromium coating and steel substrate can be divided by plasma non-transferred arc into three classes: non-molten, a little molten and molten. Good interface bonding was obtained by proper process parameters. The microhardness of chromium coating decreases with increasing energy density of plasma arc.

  20. Mechanoactivation of chromium silicide formation in the SiC-Cr-Si system

    Directory of Open Access Journals (Sweden)

    Vlasova M.

    2002-01-01

    Full Text Available The processes of simultaneous grinding of the components of a SiC-Cr-Si mixture and further temperature treatment in the temperature range 1073-1793 K were studied by X-ray phase analysis, IR spectroscopy, electron microscopy, and X-ray microanalysis. It was established that, during grinding of the mixture, chromium silicides form. A temperature treatment completes the process. Silicide formation proceeds within the framework of the diffusion of silicon into chromium. In the presence of SiO2 in the mixture, silicide formation occurs also as a result of the reduction of silica by silicon and silicon carbide. The sintering of synthesized composite SiC-chromium silicides powders at a high temperature under a high pressure (T = 2073 K, P = 5 GPa is accompanied by the destruction of cc-SiC particles, the cc/3 transition in silicon carbide and deformation distortions of the lattices of chromium silicides.

  1. Ecotoxicological tests with cadmium and chromium using postlarvae of silverside Odontesthes (Austromenidia regia regia Hildebrand

    Directory of Open Access Journals (Sweden)

    Giovana Vera

    2014-06-01

    Full Text Available In the present paper, the mean effective concentrations (EC50% of cadmium (Cd+2 and chromium (Cr+6 using postlarvae of the silverside fish Odontesthes (Austromenidia regia regia were determined. The postlarvae were exposed to different concentrations of the metals, between 0,142 and 1,208 mg.L–1 of cadmium and between 0,53 and 33,74 mg.L–1 of chromium. The mean effective concentrations (EC50% obtained were 0,648 mg.L–1 of cadmium (at 96 h and 2,68 mg.L–1 of chromium (at 96 h. Comparatively, cadmium is more toxic than chromium, and silverside is more tolerant than other organisms.

  2. Intracellular chromium localization and cell physiological response in the unicellular alga Micrasterias

    Energy Technology Data Exchange (ETDEWEB)

    Volland, Stefanie, E-mail: Stefanie.Volland@stud.sbg.ac.at [Plant Physiology Division, Cell Biology Department, University of Salzburg, Hellbrunnerstr 34, 5020 Salzburg (Austria); Luetz, Cornelius, E-mail: cornelius.luetz@uibk.ac.at [Institute of Botany, University of Innsbruck, Sternwartestrasse 15, 6020 Innsbruck (Austria); Michalke, Bernhard, E-mail: bernhard.michalke@helmholtz-muenchen.de [Helmholtz Zentrum Muenchen, German Research Centre for Environmental Health, Institute of Ecological Chemistry, Ingolstaedter Landstrasse 1, 85764 Neuherberg (Germany); Luetz-Meindl, Ursula, E-mail: ursula.luetz-meindl@sbg.ac.at [Plant Physiology Division, Cell Biology Department, University of Salzburg, Hellbrunnerstr 34, 5020 Salzburg (Austria)

    2012-03-15

    Various contaminants like metals and heavy metals are constantly released into the environment by anthropogenic activities. The heavy metal chromium has a wide industrial use and exists in two stable oxidation states: trivalent and hexavalent. Chromium can cause harm to cell metabolism and development, when it is taken up by plants instead of necessary micronutrients such as for example iron. The uptake of Cr VI into plant cells has been reported to be an active process via carriers of essential anions, while the cation Cr III seems to be taken up inactively. Micrasterias denticulata, an unicellular green alga of the family Desmidiaceae is a well-studied cell biological model organism. Cr III and VI had inhibiting effects on its cell development, while cell division rates were only impaired by Cr VI. Transmission electron microscopy (TEM) revealed ultrastructural changes such as increased vacuolization, condensed cytoplasm and dark precipitations in the cell wall after 3 weeks of Cr VI treatment. Electron energy loss spectroscopy (EELS) and electron spectroscopic imaging (ESI) were applied to measure intracellular chromium distribution. Chromium was only detected after 3 weeks of 10 {mu}M Cr VI treatment in electron dense precipitations found in bag-like structures along the inner side of the cell walls together with iron and elevated levels of oxygen, pointing toward an accumulation respectively extrusion of chromium in form of an iron-oxygen compound. Atomic emission spectroscopy (EMS) revealed that Micrasterias cells are able to accumulate considerable amounts of chromium and iron. During chromium treatment the Cr:Fe ratio shifted in favor of chromium, which implied that chromium may be taken up instead of iron. Significant and rapid increase of ROS production within the first 5 min of treatment confirms an active Cr VI uptake. SOD and CAT activity after Cr VI treatment did not show a response, while the glutathione pool determined by immuno-TEM decreased

  3. Bioremediation of the Soils Contaminated with Cadmium and Chromium, by the Earthworm Eisenia fetida

    Directory of Open Access Journals (Sweden)

    Elham Aseman- Bashiz1

    2014-07-01

    Full Text Available One of the most important environmental problems in the world is the soils contamination by heavy metals in the industrial areas, and especially the contamination of the agricultural lands. The use of earthworms to bioremediate the soils results in reducing the pollutants concentration through a bioaccumulation mechanism on the contaminants in the earthworm's body. Hence, the present study aimed to prove the biological effectiveness of Eisenia fetida earthworms in bioremediation the soils contaminated with chromium and cadmium. Concentration of chromium and cadmium pollution in soil was determined to be 0.04 mg/g and 0.08 mg/g respectively. 30 worms were added to 500 g soil samples. Chromium and cadmium concentration in soil and in the body of worms was measured at two time periods of 21 and 42 days. To measure the concentration of chromium and cadmium we used ICP spectrometry. Software in usage was SPSS version 17. There was a significant correlation between the reduction of chromium and cadmium metals in the soils and the accumulation of chromium and cadmium metals in the worm’s body. A significant decline of chromium levels of the soil was observed in the days 21 and 42 during the study compared to initial amount of 0.1 mg/g. on the other hand chromium concentration of the soil decreased from 0.14 mg/g to 0.1 mg/g after 42 days. Comparison of mortality in two different time periods showed that by passing the time and by increase in soil chromium and cadmium concentrations the death toll of worms rises. The increased mortality of worms in the soil at a concentration of 0.08 mg/g of chromium, say that using the worms for bioremediation is not recommended at such concentration of chromium but using the worms for the removal of cadmium at concentrations of 0.04 mg/g and 0.08 mg/g in the soil is recommended.

  4. Physiological, biochemical and histometric responses of Nile tilapia (Oreochromis niloticus L.) by dietary organic chromium (chromium picolinate) supplementation.

    Science.gov (United States)

    Mehrim, Ahmed I

    2014-05-01

    Chromium has been recognized as a new and important micro-nutrient, essential for both human and animal nutrition. This study was conducted to evaluate the appropriateness and/or the use of safety level of dietary chromium picolinate (Cr-Pic), and its effects on the physiological responses, the histometric characteristics, and the chemical analysis of dorsal muscles of mono-sex Nile tilapia, Oreochromis niloticus. A total of 420 fingerlings (28.00 ± 0.96 g) were randomly distributed into 21 fiberglass tanks representing seven treatments at a rate of 20 fish m(-3). The control fish group (T1) was fed a Cr-Pic free basal diet. Other fish groups were fed the basal diet supplemented with 200 (T2), 400 (T3), 600 (T4), 800 (T5), 1000 (T6) and 1200 μg Cr-Pic kg(-1) diet (T7). Diets were offered to fish at a feeding rate of 3% of life body weight for 12 weeks. Results revealed that blood hematological parameters (hemoglobin, red blood cells, packed cell volume, mean corpuscular hemoglobin concentration, blood platelets, and white blood cells lymphocytes); serum biochemical measurements (total testosterone, high density lipoprotein, total protein, albumin, and globulin); and the dry matter and crude protein of the fish dorsal muscles all have significantly increased (P ⩽ 0.05) in the T3 treatment compared with the other treatments. Meanwhile, no significant differences were found among all treatments with regard to the histometric characteristics. It can be concluded that Cr-Pic at 400 μg kg(-1) diet (T3) seems to be the most appropriate level for O. niloticus fingerlings.

  5. Physiological, biochemical and histometric responses of Nile tilapia (Oreochromis niloticus L. by dietary organic chromium (chromium picolinate supplementation

    Directory of Open Access Journals (Sweden)

    Ahmed I. Mehrim

    2014-05-01

    Full Text Available Chromium has been recognized as a new and important micro-nutrient, essential for both human and animal nutrition. This study was conducted to evaluate the appropriateness and/or the use of safety level of dietary chromium picolinate (Cr-Pic, and its effects on the physiological responses, the histometric characteristics, and the chemical analysis of dorsal muscles of mono-sex Nile tilapia, Oreochromis niloticus. A total of 420 fingerlings (28.00 ± 0.96 g were randomly distributed into 21 fiberglass tanks representing seven treatments at a rate of 20 fish m−3. The control fish group (T1 was fed a Cr-Pic free basal diet. Other fish groups were fed the basal diet supplemented with 200 (T2, 400 (T3, 600 (T4, 800 (T5, 1000 (T6 and 1200 μg Cr-Pic kg−1 diet (T7. Diets were offered to fish at a feeding rate of 3% of life body weight for 12 weeks. Results revealed that blood hematological parameters (hemoglobin, red blood cells, packed cell volume, mean corpuscular hemoglobin concentration, blood platelets, and white blood cells lymphocytes; serum biochemical measurements (total testosterone, high density lipoprotein, total protein, albumin, and globulin; and the dry matter and crude protein of the fish dorsal muscles all have significantly increased (P ⩽ 0.05 in the T3 treatment compared with the other treatments. Meanwhile, no significant differences were found among all treatments with regard to the histometric characteristics. It can be concluded that Cr-Pic at 400 μg kg−1 diet (T3 seems to be the most appropriate level for O. niloticus fingerlings.

  6. Microcalorimetric Study on Effect of Chromium(Ⅲ) and Chromium(Ⅵ) Species on the Growth of Escherichia coli

    Institute of Scientific and Technical Information of China (English)

    YAO,Jun; WANG,Yan-Xin; TIAN,Lin; WANG,Fei; CHEN,Hui-Lun; XU,Chao-Qian; SU,Chun-Li; CAI,Ming-Fa; MASKOW,Thomas; ZARAY,Gyula

    2008-01-01

    The effects of Cr(Ⅲ) and Cr(Ⅵ) species ( Cr2O2-7, CrO2-4 and Cr3+) on the growth of Escherichia coli (E.coli) have been investigated in detail by microcalorimetry at 37 ℃. Parameters including the growth rate constant (k),inhibitory ratio (Ⅰ), half-inhibitory concentration (IC50), total heat output (Qtotal), time of the maximum heat production (tlog) in the log phase have been obtained. The results showed that Cr(Ⅵ) and Cr(Ⅲ) had the inhibition effect on the growth of E. coli in aquatic environment; however, the inhibitory ratio of Cr(Ⅲ) to E. coli was smaller than that of Cr(Ⅵ). The k values of E. coli in the presence of Cr(Ⅵ) and at high concentrations of Cr(Ⅲ) were decreased with increasing the concentrations of these chromium species. Among the three chromium species investigated,Cr2O2-7 was found to be the most poisonous species against E. coli with an IC50 value of 35.52 μg·mL-1. CrO42- exhibited moderate toxicity on E. coli with an IC50 of 50.24 μg·mL-1, and Cr3+ had the lowest toxicity with an IC50 of 84.30 μg·mL-1. Microcalorimetry can provide a convenient, sensitive and reliable method to study the effect of various metal species on the growth of bacteria or other microorganisms.

  7. Mechanical Property of Low Chromium Semi-Steel Grinding Ball Prepared by Cross Rolling

    Institute of Scientific and Technical Information of China (English)

    CHANG Li-min; MENG De-liang; NIE Pu-lin; LIU Jian-hua

    2004-01-01

    The preparing method, rolling technology and mechanical properties of low chromium semi-steel grinding ball by cross rolling were studied. The results show that when the low chromium semi-steel bar is forged from 55 mm to 50 mm, cross-rolled into grinding ball at 1 000-1 050 ℃, air cooled and tempered at 550 ℃ for 2 h, the best mechanical properties, especially the abrasive resistance under the action of hard abrasive, can be obtained.

  8. Microstructure and Property of High Carbonic-Chromium Cast Steel with Different Hot Deformation Ratio

    Institute of Scientific and Technical Information of China (English)

    XU Tao; WANG Jiu-liang; ZHANG Run-jun; CHAO Guo-hua; LIU Jian-hua

    2004-01-01

    The microstructure and properties of high carbonic-chromium cast steel subjected to different hot deformation ratios were studied. The experimental results show that the microstructure and properties of high carbonic-chromium cast steel are obviously improved after hot deformation, and the best mechanical properties of the cast steel can be obtained under hot deformation ratio of 40 %-50 %, which leads to the morphology change of eutectic carbide and the precipitation of granular carbides.

  9. Biodegradation of nickel and chromium from space maintainers: An in vitro study

    OpenAIRE

    Bhaskar V; Subba Reddy V

    2010-01-01

    Band materials are often used in the practice of pediatric dentistry. Nickel and Chromium are the main ingredients of these materials. The potential health hazards of nickel and chromium and their compounds have been the focus of attention for more than 100 years. It has established that these metals could cause hypersensitivity. The study was undertaken to analyze in vitro biodegradation of space maintainers made out of stainless steel band materials from manufacturers Dentaurum and Unitek. ...

  10. Characterization of the chromium retention potential of non polluted aquifer solids in an industrial site

    OpenAIRE

    Reynal, Caroline; Kedziorek, Monika A.M.; Rollin, Claire; Bourg, Alain.C.M.

    2003-01-01

    National audience; A hydrogeochemical study of an industrial site where sulfuric acid and copper sulfate ("bouillie bordelaise") are manufactured showed that the phreatic aquifer is contaminated by copper, sulfate, chromium, arsenic and has an acid pH Field observations and laboratory experiments, both necessary if we are to understand the processes controlling tranfers at the solid-liquid interface, were used to investigate the behaviour of chromium. In the field, monitoring the mixing of po...

  11. Peat and coconut fiber as biofilters for chromium adsorption from contaminated wastewaters.

    Science.gov (United States)

    Henryk, Kołoczek; Jarosław, Chwastowski; Witold, Żukowski

    2016-01-01

    Batch adsorption experiments were performed for the removal of chromium (III) and chromium (VI) ions from aqueous solutions using Canadian peat and coconut fiber. The Langmuir model was used to describe the adsorption isotherm. The maximum adsorption for peat reached 18.75 mg/g for Cr(III) and 8.02 mg/g for Cr(VI), whereas the value for fiber was slightly higher and reached 19.21 mg/g for Cr(III) and 9.54 mg/g for Cr(VI). Both chromium forms could be easily eluted from the materials. The adsorption of chromium forms to organic matter could be explained in terms of formation of donor-acceptor chemical covalent bound with hydroxyl groups as ligands and chromium as the central atom in the formed complex. The chromate-reducing activities were monitored with the use of electron paramagnetic resonance spectroscopy. The results showed that both adsorption and reduction occurred simultaneously and the maximum adsorption capacity of hexavalent chromium being equal to 95% for fiber and 92% for peat was obtained at pH 1.5. The reduction of Cr(VI) in wastewaters began immediately and disappeared after 20 h. Both materials contained yeast and fungi species which can be responsible for reduction of chromium compounds, due to their enzymatic activity (Chwastowski and Koloczek (Acta Biochim Pol 60: 829-834, 2013)). The reduction of Cr(VI) is a two-phase process, the first phase being rapid and based on chemical reaction and the second phase having biological features. After the recovery step, both types of organic materials can be used again for chromium adsorption without any loss in the metal uptake. Both of the materials could be used as biofilters in the wastewater treatment plants.

  12. Self-focusing in chromium-doped potassium niobate single ceramic crystal

    Energy Technology Data Exchange (ETDEWEB)

    Castillo T, J.; Gonzalez M, S.; Aguirre L, A.; Hernandez, M.B.; Aguilar M, J.A. [Instituto de Fisica y Matematicas, Universidad Tecnologica de la Mixteca, 69000, Huajuapan de Leon, Oaxaca (Mexico); Hernandez A, J. [lFUNAM, PO Box 20-364, 01000 Mexico, DF (Mexico)]. e-mail: jaimec@mixteco.utm.mx

    2006-07-01

    The self-focusing and nonlinear optical absorption in a chromium-doped potassium niobate single ceramic crystal have been investigated. The third-order electric susceptibility X{sup (3)} at continuous 532 nm radiation is estimated based on a band transport model describing photo refractive properties for this electro-optic material. An anisotropic behavior on its nonlinear optical absorption properties has also been observed due to the presence of chromium ions. (Author)

  13. The influence of solidification speed during heating on allotropic transformations of chromium cast iron casting

    Directory of Open Access Journals (Sweden)

    M. Przybył

    2008-08-01

    Full Text Available The unique stand to founding dilatometric samples ("on ready” which solidify with different cooling speeds was presented. The dilatometric investigations, X-ray, metallographic they disclosed the occurrence in matrix of chromium cast iron of considerable quantity of austenite in dependence from concentration of chromium (18% and 23% and the speed of solidification. Castings these despite large part of austenite mark with high hardness in raw state.

  14. Effect of Chromium(VI Toxicity on Enzymes of Nitrogen Metabolism in Clusterbean (Cyamopsis tetragonoloba L.

    Directory of Open Access Journals (Sweden)

    Punesh Sangwan

    2014-01-01

    Full Text Available Heavy metals are the intrinsic component of the environment with both essential and nonessential types. Their excessive levels pose a threat to plant growth and yield. Also, some heavy metals are toxic to plants even at very low concentrations. The present investigation (a pot experiment was conducted to determine the affects of varying chromium(VI levels (0.0, 0.5, 1.0, 2.0, and 4.0 mg chromium(VI kg−1 soil in the form of potassium dichromate on the key enzymes of nitrogen metabolism in clusterbean. Chromium treatment adversely affect nitrogenase, nitrate reductase, nitrite reductase, glutamine synthetase, and glutamate dehydrogenase in various plant organs at different growth stages as specific enzyme activity of these enzymes decreased with an increase in chromium(VI levels from 0 to 2.0 mg chromium(VI kg−1 soil and 4.0 mg chromium(VI kg−1 soil was found to be lethal to clusterbean plants. In general, the enzyme activity increased with advancement of growth to reach maximum at flowering stage and thereafter decreased at grain filling stage.

  15. The influence of substrate temperature on the tribo- mechanical properties of chromium nitride thin films

    Science.gov (United States)

    Merie, V. V.; Negrea, G.; Modi, E.

    2016-08-01

    Different nitrides such as titanium nitride, chromium nitride and so on are used in a widespread range of applications such as cutting tools, medical implants, and microelectromechanical devices and all that due to their mechanical, physical and chemical properties. The aim of this study is to obtain chromium nitride thin films and to characterize them by atomic force microscopy investigations. The chromium nitride thin films were deposited by reactive magnetron sputtering on silicon substrates. During the deposition process, the discharge current, the argon and nitrogen flows, the pressure inside the chamber and the deposition time were kept constant. A chromium target with a purity of 99.95 % was used. Some of the films were deposited after a chromium buffer layer was previously deposited on the silicon substrate. The deposition was carried out when substrate temperature was at room temperature, at 300 and 500°C respectively. Once the films were deposited, atomic force microscopy investigations were performed in order to emphasize the influence of the substrate temperature on the topographical, mechanical and tribological characteristics. The results pointed out an important influence of the substrate temperature on topographical, mechanical and tribological properties of the investigated chromium nitride thin films.

  16. Fabrication of Unique Magnetic Bionanocomposite for Highly Efficient Removal of Hexavalent Chromium from Water

    Science.gov (United States)

    Zhong, Yunlei; Qiu, Xun; Chen, Dongyun; Li, Najun; Xu, Qingfeng; Li, Hua; He, Jinghui; Lu, Jianmei

    2016-08-01

    Biotreatment of hexavalent chromium has attracted widespread interest due to its cost effective and environmental friendliness. However, the difficult separation of biomass from aqueous solution and the slow hexavalent chromium bioreduction rate are bottlenecks for biotechnology application. In this approach, a core-shell structured functional polymer coated magnetic nanocomposite was prepared for enriching the hexavalent chromium. Then the nanocomposite was connected to the bacteria via amines on bacterial (Bacillus subtilis ATCC-6633) surface. Under optimal conditions, a series of experiments were launched to degrade hexavalent chromium from the aqueous solution using the as-prepared bionanocomposite. Results showed that B. subtilis@Fe3O4@mSiO2@MANHE (BFSM) can degrade hexavalent chromium from the water more effectively (a respectable degradation efficiency of about 94%) when compared with pristine B. subtilis and Fe3O4@mSiO2@MANHE (FSM). Moreover, the BFSM could be separated from the wastewater by magnetic separation technology conveniently due to the Fe3O4 core of FSM. These results indicate that the application of BFSM is a promising strategy for effective treating wastewater containing hexavalent chromium.

  17. Chromium (III Removal and Recovery from Tannery Wastewater by Precipitation Process

    Directory of Open Access Journals (Sweden)

    Abass Esmaeili

    2005-01-01

    Full Text Available Chromium (III salts are the most widely used chemicals for tanning processes, but 60-70% of total chromium salts reacts with the hides. In the other word, about 30-40% of the chromium amount remains in the solids and liquid wastes (especially spent tanning solutions. Therefore, the removal and recovery of the chromium content of these wastewaters are necessary for environmental protection and economic reasons. Removal and recovery of chromium were carried out by using precipitation process. For this purpose, three precipitating agents calcium hydroxide, sodium hydroxide and magnesium oxide were used. The effects of pH, stirring time, settling rate and sludge volume were studied in batch experiments. Results show that the optimum pH is 8-9 and the good sludge with high settling rate and lower volume obtain by the MgO precipitating agent. Hence the MgO is a good precipitating agent for removal and recovery of chromium from tanning wastewater.

  18. Chromium redistribution in thermally aged and irradiated ferritic-martensitic steels

    Energy Technology Data Exchange (ETDEWEB)

    Camus, E.; Wanderka, N.; Welzel, S.; Wollenberger, H. [Hahn-Meitner-Institut Berlin GmbH (Germany); Materna-Morris, E. [Forschungszentrum Karlsruhe, Postfach 3640, D-76021 Karlsruhe (Germany)

    1998-07-15

    Ferritic-martensitic steels containing 8-12 at.% chromium are considered as structural materials for spallation sources and fusion reactors. Materials will be subjected to intense damage rates, e.g. 50-100 dpa per year at full power. Therefore, the behavior under irradiation of these steels must be investigated. Our earlier dual-beam irradiation results on the DIN 1.4914 steel showed a decomposition into chromium-enriched and chromium-depleted regions. The mean concentration of the chromium-depleted regions was found to be 5.19{+-}0.32 at.% after irradiation at 500 C to a fluence of 50 dpa, as measured by atom probe field-ion microscopy. The chromium distribution in the matrix of the DIN 1.4914 steel after thermal ageing at temperatures between 400 and 600 C has been investigated for times up to 17000 h. The carbides were characterized by means of transmission electron microscopy and extraction replicas. The concentrations of the constituents of the matrix were measured by means of atom probe. The mean chromium concentrations in the matrix are found to be 8.66{+-}0.32, 4.5{+-}0.3, and 7.2{+-}0.4 at.%, after ageing at 400, 500, and 600 C, respectively. The matrix contains virtually no carbon. The results are discussed in terms of phase decomposition and species segregation. (orig.) 15 refs.

  19. Alpha -tocopherol supplementation on chromium toxicity : a study on rat liver and kidney cell membrane

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    Membrane damage is one of the important consequence of chromium, an environmental toxicant, to produce cytotoxicity. α-tocopherol, a membrane protectant can be used to reduce the chromium-induced membrane damage. In the present study, the impact of chromium in presence and absence of α-tocopherol was studied on plasma membrane of liver and kidney in male Wistar rats (80 - 100g body weight). Significant increase in membrane cholesterol level as well as significant decrease in membrane phospholipid level in chromium exposed ( 0.8 mg /100g body weight/d, i.p., for 4 weeks) animals suggest structural alteration of both liver and kidney plasma memebrane. The alkaline phosphatase, total ATPase and Na+-K+-ATPase activities of plasma membrane were significantly decreased in both liver and kidney after chromium treatment. However, α-tocopherol (30 mg / 100g diet) supplementation can restrict the changes in these membrane-bound enzyme activities. Thus, the usefulness of dietary supplementation of α-tocopherol to restrain the chromium-induced membrane damage is suggested.

  20. Influence of dietary supplementation of chromium on the carcass traits of crossbred pigs

    Directory of Open Access Journals (Sweden)

    Guikinglung Pamei

    2014-09-01

    Full Text Available This study was conducted to assess the influence of chromium on the carcass traits in crossbred (Large White Yorkshire X Landrace pigs fed with swill feeding for a period of 5 months. Early-weaned crossbred piglets (n=24 were selected for this study, and the piglets were randomly divided into three equal groups; Group I, II, and III. The piglets were reared by following standard health coverage protocols. The feeds of Group I and II were supplemented with chromium in the form of chromium tripicolinate at 0.1 and 0.2 mg/kg of swill feed respectively, and Group III was kept as control. Carcass weight, carcass length, and bone percentage showed no significant difference among the three groups. However, better dressing percentage was observed in Group I (p<0.05. Liver and kidney weights were reduced in chromium supplemented groups (p<0.05. Chromium supplemented groups showed lower backfat thickness and fat percentage (p<0.01; whereas, loin eye areas and muscle percentage were increased as compared to the control group. Thus, it was concluded that chromium supplementation in feed of crossbred piglets influenced positively in their carcass traits.

  1. Ability of Bacillus mucilaginosus GY03 Strain to Adsorb Chromium Ions

    Institute of Scientific and Technical Information of China (English)

    CHEN Ye; LIAN Bin

    2005-01-01

    A research with Bacillus mucilaginosus cultured in nitrogen-free medium for forming a flocculant material to adsorb Cr+6 was conducted to determine the effects of different pH, volume, treatment time, and chromium (Ⅵ) concentrations on chromium (Ⅵ) adsorption by microbial flocculant (MBF), which was produced from the B. mucilaginosus GY03 strain. The results showed that MBF had outstanding flocculation on chromium (Ⅵ). Based on the results of a oneway experiment and actual wastewater treatment conditions, the optimum conditions, obtained by using orthogonal experiments, for chromium (Ⅵ) adsorption by MBF were: Cr6+ solution pH of 9, flocculant material volume of 15 mL,treatment time of 12 h and chromium ion concentration of 30 mg L-1. The results demonstrated that the MBF produced from GY03 could be used in the chromium-containing wastewater treatment. Meanwhile, after extraction and analysis of the MBF polysaccharides, it was found that MBF was mainly composed of glycoprotein. Analysis on constituents of monosaccharide showed that polysaccharides of B. mucilaginosus were composed of rhamnose, glucose etc. Thus, because it was applied over a wide range of pH, in small amounts and had a rapid flocculation speed the flocculant used in this experiment had a vast field of application potential.

  2. Photocatalysis with chromium-doped TiO2: bulk and surface doping.

    Science.gov (United States)

    Ould-Chikh, Samy; Proux, Olivier; Afanasiev, Pavel; Khrouz, Lhoussain; Hedhili, Mohamed N; Anjum, Dalaver H; Harb, Moussab; Geantet, Christophe; Basset, Jean-Marie; Puzenat, Eric

    2014-05-01

    The photocatalytic properties of TiO2 modified by chromium are usually found to depend strongly on the preparation method. To clarify this problem, two series of chromium-doped titania with a chromium content of up to 1.56 wt % have been prepared under hydrothermal conditions: the first series (Cr:TiO2) is intended to dope the bulk of TiO2, whereas the second series (Cr/TiO2) is intended to load the surface of TiO2 with Cr. The catalytic properties have been compared in the photocatalytic oxidation of formic acid. Characterization data provides evidence that in the Cr/TiO2 catalysts chromium is located on the surface of TiO2 as amorphous CrOOH clusters. In contrast, in the Cr:TiO2 series, chromium is mostly dissolved in the titania lattice, although a minor part is still present on the surface. Photocatalytic tests show that both series of chromium-doped titania demonstrate visible-light-driven photo-oxidation activity. Surface-doped Cr/TiO2 solids appear to be more efficient photocatalysts than the bulk-doped Cr:TiO2 counterparts.

  3. Cathodic cage nitriding of AISI 409 ferritic stainless steel with the addition of CH4

    Directory of Open Access Journals (Sweden)

    Rômulo Ribeiro Magalhães de Sousa

    2012-04-01

    Full Text Available AISI 409 ferritic stainless steel samples were nitrided using the cathodic cage plasma nitriding technique (CCPN, with the addition of methane to reduce chromium precipitation, increase hardness and wear resistance and reduce the presence of nitrides when compared to plasma carbonitriding. Microhardness profiles and X-Ray analysis confirm the formation of a very hard layer containing mainly ε-Fe3N and expanded ferrite phases.

  4. Lead-chromium carbonyl complexes incorporated with group 8 metals: synthesis, reactivity, and theoretical calculations.

    Science.gov (United States)

    Shieh, Minghuey; Chu, Yen-Yi; Hsu, Miao-Hsing; Ke, Wei-Ming; Lin, Chien-Nan

    2011-01-17

    The trichromium-lead complex [Pb{Cr(CO)5}3](2-) (1) was isolated from the reaction of PbCl2 and Cr(CO)6 in a KOH/MeOH solution, and the new mixed chromium-iron-lead complex [Pb{Cr(CO)5}{Fe(CO)4}2](2-) (3) was synthesized from the reaction of PbCl2 and Cr(CO)6 in a KOH/MeOH solution followed by the addition of Fe(CO)5. X-ray crystallography showed that 3 consisted of a central Pb atom bound in a trigonal-planar environment to two Fe(CO)4 and one Cr(CO)5 fragments. When complex 1 reacted with 1.5 equiv of Mn(CO)5Br, the Cr(CO)4-bridged dimeric lead-chromium carbonyl complex [Pb2Br2Cr4(CO)18](2-) (4) was produced. However, a similar reaction of 3 or the isostructural triiron-lead complex [Pb{Fe(CO)4}3](2-) (2) with Mn(CO)5Br in MeCN led to the formation of the Fe3Pb2-based trigonal-bipyramidal complexes [Fe3(CO)9{PbCr(CO)5}2](2-) (6) and [Fe3(CO)9{PbFe(CO)4}2](2-) (5), respectively. On the other hand, the Ru3Pb2-based trigonal-bipyramidal complex [Ru3(CO)9{PbCr(CO)5}2](2-) (7) was obtained directly from the reaction of PbCl2, Cr(CO)6, and Ru3(CO)12 in a KOH/MeOH solution. X-ray crystallography showed that 5 and 6 each had an Fe3Pb2 trigonal-bipyramidal core geometry, with three Fe(CO)3 groups occupying the equatorial positions and two PbFe(CO)4 or PbCr(CO)5 units in the axial positions, while 7 displayed a Ru3Pb2 trigonal-bipyramidal geometry with three equatorial Ru(CO)3 groups and two axial PbCr(CO)5 units. The complexes 3-7 were characterized spectroscopically, and their nature, formation, and electrochemistry were further examined by molecular orbital calculations at the B3LYP level of density functional theory.

  5. Embryotoxicity hazard assessment of methylmercury and chromium using embryonic stem cells.

    Science.gov (United States)

    Stummann, T C; Hareng, L; Bremer, S

    2007-12-05

    The embryonic stem cell test (EST) has been scientifically validated (2001) as an in vitro embryotoxicity test, showing a good overall test accuracy of 78%. Methylmercury (MeHg) was the most significant outlayer identified, as the metal was the only strong in vivo embryotoxicant falsely predicted to be non-embryotoxic. The EST misclassification of MeHg, and the potential environmental exposure and developmental toxic hazards of heavy metals gave us the rationale to investigate whether the EST can correctly predict the embryotoxic potential of two heavy metals different from MeHg. The EST correctly classified trivalent chromium to be non-embryotoxic and hexavalent chromium to be embryotoxic, while we confirmed the misclassification of MeHg. MeHg causes developmental abnormalities in the brain. We therefore aimed to improve the in vitro prediction of MeHg embryotoxicity by including a neuronal ES cell differentiation assay. Differentiation of neuronal-like cells was demonstrated by real-time PCR experiments, showing up-regulation of several neuronal marker genes, and immunohistochemistry, demonstrating the appearance of nestin, neurofilament medium polypeptide, beta-tubulin III and microtubule-associated protein 2 (Mtap2) positive cells. We identified Mtap2 mRNA expression as a sensitive toxicological endpoint for MeHg-induced neuronal embryotoxicity, as Mtap2 mRNA was down-regulated in the presence of non-cytotoxic concentrations of MeHg. Noticeably, several other neuronal marker genes were unaffected by MeHg and Mtap2 expression was not affected until day 14 of differentiation. This implies that the total neuronal-like cell number was unchanged and that the down-regulation of Mtap2 expression reflects neuron-specific toxicity, i.e. instability of the neuron-specific microtubules, and arrest of the neuronal maturation. The fact, that most marker genes were unaffected by MeHg, stresses the importance of including an array of marker genes. In conclusion, our results

  6. Magnetic face-to-face interaction and electrocommunication in chromium sandwich compounds.

    Science.gov (United States)

    Elschenbroich, Christoph; Kanellakopulos, Basil; Köhler, Frank H; Metz, Bernhard; Lescouëzec, Rodrigue; Mitzel, Norbert W; Strauss, Werner

    2007-01-01

    The reaction of [{(C5Me5)CrCl2}2] with [2.2](1,4)cyclophane gave [(C5Me5)Cr{[2.2](1,4)cyclophane}] (1) and [(C5Me5)Cr{[2.2](1,4)cyclophane}Cr(C5Me5)] (2), depending on the reaction conditions. X-ray structure analysis showed 2 to be a ministack which in turn is stacked in the lattice. The chromium atoms are 6.035 A apart, and the distortion of the benzene rings to boat-shaped moieties is less pronounced than in parent [2.2](1,4)cyclophane. The NMR and EPR spectra were consistent with a S=1/2 ground state for 1 and with two interacting S=1/2 centers in 2. Spin density was found in the ligand pi systems, where its sign was negative when the pi system was adjacent to chromium, while on the nonbonded benzene moiety of 1 it was positive. Cyclic voltammograms showed reductions to 1- and 2(2-), as well as oxidations to 1+, 2+, and 2(2+) which were quasireversible, whereas oxidations to 1(2+) and 2(3+) were irreversible. Interaction between the metal ions was revealed by a 260 mV separation of the redox waves belonging to 2+, and 2(2+). Both cations were isolated as [B(C6H5)4]- salts, which in solution decomposed to [2.2](1,4)cyclophane and [(C5Me5)Cr{(eta6-C6H5)B(C6H5)3}] (3). The 1H and 13C NMR spectra of 3 were in accordance with an S=1 ground state. Solid-state magnetic measurements of the dimetallic compounds showed antiferromagnetic interaction with J=-122 cm-1 for 2, J=-31 cm-1 for 2+ (ground state S=1/2), and J=-23.5 cm-1 for 2(2+) (with H=-JS1S2). The decrease of J in the series 2, 2+, and 2(2+) was traced to the number of unpaired electrons and, for the mixed-valent cation 2+, to additional double exchange.

  7. Effect of some non functional surfactants and electrolytes on the hexavalent chromium reduction by glycerol. A mechanistic study

    Energy Technology Data Exchange (ETDEWEB)

    Basu, A.; Ghosh, S.K.; Saha, R.; Nandi, R.; Saha, B. [Burdwan Univ., WB (India). Dept. of Chemistry; Gosh, T. [A.B.N. Seal College, Coochbehar, WB (India). Dept. of Chemistry

    2011-11-15

    Hexavalent chromium is a widespread environmental contaminant and a known human carcinogen. Kinetics of reduction of hexavalent chromium by bio-molecule glycerol in micellar media have been studied spectrophotometrically. The cytoplasmic reduction of hexavalent chromium to trivalent chromium occurs in micro-heterogeneous systems. In vitro, the micelles are considered to mimic the cellular membranes. The electron transfer processes occurring in the micellar systems is considered as model to obtain insight into the electron transport process prevailing in biological systems. Micellar media is also a probe to establish the mechanistic paths of reduction of hexavalent chromium to trivalent chromium. Effects of electrolytes common to biological system are studied to establish the proposed reaction mechanism strongly. (orig.)

  8. Effect of clay minerals and nanoparticles on chromium fractionation in soil contaminated with leather factory waste.

    Science.gov (United States)

    Taghipour, Marzieh; Jalali, Mohsen

    2015-10-30

    This study was conducted to investigate the effect of time, clay minerals and nanoparticles (NPs) on chromium (Cr) fractionation in a soil contaminated with leather factory waste (LFW). Soil was mixed with LFW, then, the contaminated soils were treated with clay minerals (bentonite and zeolite) and nanoparticles (MgO, TiO2 and ZnO) at 5% and 1%, respectively. The samples were incubated for 15-180 days at 25 °C and constant moisture. After incubation, Cr in control and treated soils was fractionated by the sequential extraction procedure. The distribution of various Cr fractions in control soil indicated that the greatest amounts of Cr were found in the residual fraction (RES) followed by the carbonate (CAR), organic matter (OM) and exchangeable (EXC) fractions. The addition of LFW in soils increased Cr concentration in all fractions. The higher proportion of EXC fraction in the soil treated with LFW indicates its higher potential of leaching and runoff transport. In all treated soils, the RES fraction was increased, while EXC and OM fractions were decreased during incubation. The results indicated that NPs are effective adsorbent for the removal of Cr ions from LFW treated soil, and they could be useful in reducing their environment risk.

  9. A quantum Monte Carlo study of the ground state chromium dimer

    CERN Document Server

    Hongo, Kenta

    2011-01-01

    We report variational and diffusion quantum Monte Carlo (VMC and DMC) studies of the binding curve of the ground-state chromium dimer. We employed various single determinant (SD) or multi-determinant (MD) wavefunctions multiplied by a Jastrow fuctor as a trial/guiding wavefunction. The molecular orbitals (MOs) in the SD were calculated using restricted or unrestricted Hartree-Fock or density functional theory (DFT) calculations where five commonly-used local (SVWN5), semi-local (PW91PW91 and BLYP), and hybrid (B1LYP and B3LYP) functionals were examined. The MD expansions were obtained from the complete-active space SCF, generalized valence bond, and unrestricted configuration interaction methods. We also adopted the UB3LYP-MOs to construct the MD expansion (UB3LYP-MD) and optimized their coefficients at the VMC level. In addition to the wavefunction dependence, we investigated the time-step bias in the DMC calculation and the effects of pseudopotentials and backflow transformation for the UB3LYP-SD case. Some...

  10. Microstructural characterization of 5-9% chromium reduced-activation steels

    Energy Technology Data Exchange (ETDEWEB)

    Jayaram, R. [Univ. of Pittsburgh, PA (United States); Klueh, R.L. [Oak Ridge National Lab., TN (United States)

    1997-08-01

    The microstructures of a 9Cr-2W-0.25-0.1C (9Cr-2WV), a 9Cr-2W-0.25V-0.07Ta-0.1C (9Cr-2WVTa), a 7Cr-2W-0.25V-0.07Ta-0.1C (7Cr-2WVTa), and a 5Cr-2W-0.25V-0.07Ta-0.1C (5Cr-2WVTa) steel (all compositions are in weight percent) have been characterized by Analytical Electron Microscopy (AEM) and Atom Probe Field Ion Microscopy (APFIM). The matrix in all four reduced-activation steels was 100% martensite. In the two 9Cr steels, the stable precipitates were blocky M{sub 23}C{sub 6} and small spherical MC. The two lower-chromium steels contained blocky M{sub 7}C{sub 3} and small needle-shaped carbonitrides in addition to M{sub 23}C{sub 6}. AEM and APFIM analysis revealed that in the steels containing tantalum, the majority of the tantalum was in solid solution. The experimental observations were in good agreement with phases and compositions predicted by phase equilibria calculations.

  11. Investigation of Hexavalent Chromium Flux to Groundwater at the 100-C-7:1 Excavation Site

    Energy Technology Data Exchange (ETDEWEB)

    Truex, Michael J.; Vermeul, Vincent R.; Fritz, Brad G.; Mackley, Rob D.; Horner, Jacob A.; Johnson, Christian D.; Newcomer, Darrell R.

    2012-11-16

    Deep excavation of soil has been conducted at the 100-C-7 and 100-C-7:1 waste sites within the 100-BC Operable Unit at the Department of Energy (DOE) Hanford Site to remove hexavalent chromium (Cr(VI)) contamination with the excavations reaching to near the water table. Soil sampling showed that Cr(VI) contamination was still present at the bottom of the 100-C-7:1 excavation. In addition, Cr(VI) concentrations in a downgradient monitoring well have shown a transient spike of increased Cr(VI) concentration following initiation of excavation. Potentially, the increased Cr(VI) concentrations in the downgradient monitoring well are due to Cr(VI) from the excavation site. However, data were needed to evaluate this possibility and to quantify the overall impact of the 100-C-7:1 excavation site on groundwater. Data collected from a network of aquifer tubes installed across the floor of the 100-C-7:1 excavation and from temporary wells installed at the bottom of the entrance ramp to the excavation were used to evaluate Cr(VI) releases into the aquifer and to estimate local-scale hydraulic properties and groundwater flow velocity.

  12. [The determination of chromium in feeds by flame atomic absorption spectrophotometry].

    Science.gov (United States)

    Wang, Jian; Jia, Bin; Guo, Li-ping; Lin, Qiu-ping

    2005-07-01

    Chromium in feeds is regulated by China Standard GB 13078-2001. A method of flame atomic absorption spectrophotometry for the determination of Cr in feeds has been developed in allusion to shortage of China standard method. Several acetylene flow-rate, burner-high and the additive of interference suppressor NH4Cl were studied respectively on the effect of sensitivities of Cr(III) and Cr(VI). The two sets analytical average results of Cr in feed sample determined by calibration curves of Cr(III) and Cr(VI) were tested by t test, no marked discrepancy was found. Optimum instrumental conditions of Cr(III) and Cr(VI) with same sensitivity were confirmed. Sensitivity was 0.014 microg x mL(-1) with detection limit 0.70 mg x kg(-1). The recoveries were 94.4%-104.9%. Relative standard deviation of sample determination (5-6 times) was 1.90%-4.08%. This method is simply, fast and exact, the detection limit was answered for Cr limit in feeds regulated by GB 13078-2001, it can be applied to the analysis of Cr in feeds.

  13. Chromium geochemistry of serpentinous sediment in the Willow core, Santa Clara County, California

    Science.gov (United States)

    Oze, Christopher J.; LaForce, Matthew J.; Wentworth, Carl M.; Hanson, Randall T.; Bird, Dennis K.; Coleman, Robert G.

    2003-01-01

    A preliminary investigation of Cr geochemistry in serpentinous sediment completed for a multiple-aquifer ground-water monitoring well (Willow core of Santa Clara County, CA) determined sediment at depths >225 meters contains Cr concentrations ranging from 195 to 1155 mg/kg. Serpentinous sediment from this site is a potential source of non-anthropogenic Cr contamination. Chromium-bearing minerals such as Cr-spinel appear to be the main source of Cr in the sediment; however, Cr-bearing silicates and clay minerals are additional Cr sources. Aqueous Cr concentrations in the sediment are <4.6 mg/L; however, the valence of Cr was not identified in the solutions or in the sediment. Although there is no indication of Cr(VI) contamination derived from the serpentinous sediment, elevated Cr concentrations in the sediment, the observed ‘dissolution’ textures of the Cr-bearing minerals, the estimated redox environment, and water chemistry indicate the formation of Cr(VI) is potentially favorable.

  14. Hexavalent chromium reduction and energy recovery by using dual-chambered microbial fuel cell.

    Science.gov (United States)

    Gangadharan, Praveena; Nambi, Indumathi M

    2015-01-01

    Microbial fuel cell (MFC) technology is utilized to treat hexavalent chromium (Cr(VI)) from wastewater and to generate electricity simultaneously. The Cr(VI) is bioelectrochemically reduced to non-toxic Cr(III) form in the presence of an organic electron donor in a dual-chambered MFC. The Cr(VI) as catholyte and artificial wastewater inoculated with anaerobic sludge as anolyte, Cr(VI) at 100 mg/L was completely removed within 48 h (initial pH value 2.0). The total amount of Cr recovered was 99.87% by the precipitation of Cr(III) on the surface of the cathode. In addition to that 78.4% of total organic carbon reduction was achieved at the anode chamber within 13 days of operation. Furthermore, the maximum power density of 767.01 mW/m² (2.08 mA/m²) was achieved by MFCs at ambient conditions. The present work has successfully demonstrated the feasibility of using MFCs for simultaneous energy production from wastewater and reduction of toxic Cr(VI) to non-toxic Cr(III).

  15. Effect of the Chromium Ion Adsorption on the Photoluminescent Properties of Titanium Dioxide

    Directory of Open Access Journals (Sweden)

    V.V. Shimanovska

    2016-03-01

    Full Text Available We have studied the photoluminescence (PL of nanocrystalline titanium dioxide (TiO2, synthesized by the thermal hydrolysis in the form of anatase (A or rutile (R, the surface of which has been modified by adsorption of chromium ions (Cr3+. The samples were characterized by X-ray diffraction, X-ray fluorescence, Raman spectroscopy and optical absorption. PL spectra were excited by a nitrogen UV laser. It was found that the processes of the PL emission and optical absorption near the band gap edge of anatase and rutile TiO2 occur with the same electronic transitions. In the Cr3+-doped R/TiO2, the process of nonradiative Auger recombination leads to the quenching of the PL intensity. The Cr3+ ion doping in А/TiO2 leads to short-wave and long-wave shifts of the PL peaks due to the Burstein-Moss effect and due to the contribution of radiation "tails" of the electron density of states, respectively. PL intensity of the Cr3+-doped A/TiO2 at low concentration of Cr3+ (up to 0.5 at. % increases in comparison with the undoped A/TiO2 due to the formation of additional centers of radiative recombination of carriers. With increasing concentration of Cr3+ (~ 1.0 at. %, the TiO2 PL intensity decreases due to the concentration quenching.

  16. Magnetite nanoparticle (NP) uptake by wheat plants and its effect on cadmium and chromium toxicological behavior.

    Science.gov (United States)

    López-Luna, J; Silva-Silva, M J; Martinez-Vargas, S; Mijangos-Ricardez, O F; González-Chávez, M C; Solís-Domínguez, F A; Cuevas-Díaz, M C

    2016-09-15

    The aim of this work was to assess the uptake of citrate-coated magnetite nanoparticles (NPs) by wheat plants and its effect on the bioaccumulation and toxicity of individual and joint Cd(2+) and Cr(6+) levels. Seven-day assays were conducted using quartz sand as the plant growth substrate. The endpoints measured were seed germination, root and shoot lengths, and heavy metal accumulation. Magnetite exhibited very low toxicity, regardless of the wheat seedling NP uptake and distribution into roots and shoots. The seed germination and shoot length were not sensitive enough, while the root length was a more sensitive toxicity endpoint. The root length of wheat seedlings exposed to individual metals decreased by 50% at 2.67mgCd(2)(+)kg(-1) and 5.53mgCr(6+)kg(-1). However, when magnetite NPs (1000mgkg(-1)) were added, the root length of the plants increased by 25 and 50%. Cd(2+) and Cr(6+) showed similar and noninteractive joint action, but strongly impaired the wheat seedlings. In contrast, an interactive infra-additive or antagonistic effect was observed upon adding magnetite NPs. Thus, cadmium and chromium accumulation in vegetable tissues was considerately diminished and the toxicity alleviated.

  17. [Food additives and healthiness].

    Science.gov (United States)

    Heinonen, Marina

    2014-01-01

    Additives are used for improving food structure or preventing its spoilage, for example. Many substances used as additives are also naturally present in food. The safety of additives is evaluated according to commonly agreed principles. If high concentrations of an additive cause adverse health effects for humans, a limit of acceptable daily intake (ADI) is set for it. An additive is a risk only when ADI is exceeded. The healthiness of food is measured on the basis of nutrient density and scientifically proven effects.

  18. Insulin sensitizing effects of oligomannuronate-chromium (III complexes in C2C12 skeletal muscle cells.

    Directory of Open Access Journals (Sweden)

    Cui Hao

    Full Text Available BACKGROUND: It was known that the insulin resistance in skeletal muscle is a major pathogenic factor in diabetes mellitus. Therefore prevention of metabolic disorder caused by insulin resistance and improvement of insulin sensitivity are very important for the therapy of type 2 diabetes. In the present study, we investigated the ability of marine oligosaccharides oligomannuronate and its chromium (III complexes from brown alga to enhance insulin sensitivity in C2C12 skeletal muscle cells. METHODOLOGY/PRINCIPAL FINDINGS: We demonstrated that oligomannuronate, especially its chromium (III complexes, enhanced insulin-stimulated glucose uptake and increased the mRNA expression of glucose transporter 4 (GLUT4 and insulin receptor (IR after their internalization into C2C12 skeletal muscle cells. Additionally, oligosaccharides treatment also significantly enhanced the phosphorylation of proteins involved in both AMP activated protein kinase (AMPK/acetyl-CoA carboxylase (ACC and phosphoinositide 3-kinase (PI3K/protein kinase B (Akt signaling pathways in C2C12 cells, indicating that the oligosaccharides activated both the insulin signal pathway and AMPK pathways as their mode of action. Moreover, oligosaccharides distributed to the mitochondria after internalization into C2C12 cells and increased the expression of transcriptional regulator peroxisome proliferator-activated receptor γ coactivator-1α (PGC-1α, carnitine palmitoyl transferase-1 (CPT-1, and phosphorylated acetyl-CoA carboxylase (p-ACC, which suggested that the actions of these oligosaccharides might be associated with mitochondria through increasing energy expenditure. All of these effects of marine oligosaccharides were comparable to that of the established anti-diabetic drug, metformin. In addition, the treatment with oligosaccharides showed less toxicity than that of metformin. CONCLUSIONS/SIGNIFICANCE: Our findings indicate that oligomannuonate and its chromium (III complexes improved

  19. Investigation of the weldability of iron-aluminum-chromium overlay coatings for corrosion protection in oxidizing/sulfidizing environments

    Science.gov (United States)

    Regina, Jonathan R.

    The current study investigated the effect of chromium additions on the hydrogen cracking susceptibility of Fe-Al weld overlay claddings containing chromium additions. It was found that the weldability of FeAlCr claddings was a function of both the aluminum and chromium concentrations of the weld coatings. Weld overlay compositions that were not susceptible to hydrogen cracking were identified and the underlying mechanism behind the hydrogen cracking phenomenon was investigated further. It was concluded that the cracking behavior of the FeAlCr welds depended strongly on the microstructure of the weld fusion zone. Although it was found that the cracking susceptibility was influenced by the presence of Fe-Al intermetallic phases (namely Fe3 Al and FeAl), the cracking behavior of FeAlCr weld overlay claddings also depended on the size and distribution of carbide and oxide particles present within the weld structure. These particles acted as hydrogen trapping sites, which are areas where free hydrogen segregates and can no longer contribute to the hydrogen embrittlement of the metal. It was determined that in practical applications of these FeAlCr weld overlay coatings, carbon should be present within these welds to reduce the amount of hydrogen available for hydrogen cracking. Based on the weldability results of the FeAlCr weld claddings, coating compositions that were able to be deposited crack-free were used for long-term corrosion testing in a simulated low NOx environment. These alloys were compared to a Ni-based superalloy (622), which is commonly utilized as boiler tube coatings in power plant furnaces for corrosion protection. It was found that the FeAlCr alloys demonstrated superior corrosion resistance when compared to the Ni-based superalloy. Due to the excellent long-term corrosion behavior of FeAlCr weld overlays that were immune to hydrogen cracking, it was concluded that select FeAlCr weld overlay compositions would make excellent corrosion resistant

  20. Genesis and transport of hexavalent chromium in the system ophiolitic rocks - groundwater

    Science.gov (United States)

    Shchegolikhina, Anastasia; Guadagnini, Laura; Guadagnini, Alberto

    2015-04-01

    Our study aims at contributing to the quantification and characterization of chromium transport processes from host rocks and soil matrices to groundwater. We focus on dissolved hexavalent chromium detected in groundwaters of geological regions with ophiolitic rocks (ophiolites and serpentinites) inclusions due to its critical ecological impact. (Oze et al., 2004). Despite the large number of analyses on the occurrence of high concentrations of hazardous hexavalent chromium ions in natural waters, only few studies were performed with the objective of identifying and investigating the geochemical reactions which could occur in the natural system rock - groundwater - dissolved chromium (Fantoni et al., 2002, Stephen and James, 2004, Lelli et al., 2013). In this context, there is a need for integration of results obtained from diverse studies in various regions and settings to improve our knowledge repository. Our theoretical analyses are grounded and driven by practical scenarios detected in subsurface reservoirs exploited for civil and industrial use located in the Emilia-Romagna region (Italy). Available experimental datasets are complemented with data from other international regional-scale settings (Altay mountains region, Russia). Modeling of chromium transformation and migration particularly includes characterization of the multispecies geochemical system. A key aspect of our study is the analysis of the complex competitive sorption processes governing heavy metal evolution in groundwater. The results of the research allow assessing the critical qualitative features of the mechanisms of hexavalent chromium ion mobilization from host rocks and soils and the ensuing transformation and migration to groundwater under the influence of diverse environmental factors. The study is then complemented by the quantification of the main sources of uncertainty associated with prediction of heavy metal contamination levels in the groundwater system explored. Fantoni, D

  1. Fluctuations in Precambrian atmospheric oxygenation recorded by chromium isotopes.

    Science.gov (United States)

    Frei, Robert; Gaucher, Claudio; Poulton, Simon W; Canfield, Don E

    2009-09-10

    Geochemical data suggest that oxygenation of the Earth's atmosphere occurred in two broad steps. The first rise in atmospheric oxygen is thought to have occurred between approximately 2.45 and 2.2 Gyr ago, leading to a significant increase in atmospheric oxygen concentrations and concomitant oxygenation of the shallow surface ocean. The second increase in atmospheric oxygen appears to have taken place in distinct stages during the late Neoproterozoic era ( approximately 800-542 Myr ago), ultimately leading to oxygenation of the deep ocean approximately 580 Myr ago, but details of the evolution of atmospheric oxygenation remain uncertain. Here we use chromium (Cr) stable isotopes from banded iron formations (BIFs) to track the presence of Cr(VI) in Precambrian oceans, providing a time-resolved picture of the oxygenation history of the Earth's atmosphere-hydrosphere system. The geochemical behaviour of Cr is highly sensitive to the redox state of the surface environment because oxidative weathering processes produce the oxidized hexavalent [Cr(VI)] form. Oxidation of reduced trivalent [Cr(III)] chromium on land is accompanied by an isotopic fractionation, leading to enrichment of the mobile hexavalent form in the heavier isotope. Our fractionated Cr isotope data indicate the accumulation of Cr(VI) in ocean surface waters approximately 2.8 to 2.6 Gyr ago and a likely transient elevation in atmospheric and surface ocean oxygenation before the first great rise of oxygen 2.45-2.2 Gyr ago (the Great Oxidation Event). In approximately 1.88-Gyr-old BIFs we find that Cr isotopes are not fractionated, indicating a decline in atmospheric oxygen. Our findings suggest that the Great Oxidation Event did not lead to a unidirectional stepwise increase in atmospheric oxygen. In the late Neoproterozoic, we observe strong positive fractionations in Cr isotopes (delta(53)Cr up to +4.9 per thousand), providing independent support for increased surface oxygenation at that time, which may

  2. Chromium uptake by Saccharomyces cerevisiae and isolation of glucose tolerance factor from yeast biomass

    Indian Academy of Sciences (India)

    Vlatka Gulan Zetic; Vesna Stehlik-Tomas; Slobodan Grba; Lavoslav Lutilsky; Damir Kozlek

    2001-06-01

    Fermentations with yeast Saccharomyces cerevisiae in semiaerobic and in static conditions with the addition of chromic chloride into the used molasses medium were analysed. It was proved that the addition of optimal amounts of CrCl3 into the basal medium enhanced the kinetics of alcohol fermentations. The addition of 200 mg/l CrCl3 into the medium stimulated both the yeast growth and the ethanol production in all experimental conditions. On the other hand, the results showed that Cr3+ ions were incorporated into yeast cells during fermentation. Under these conditions the accumulation of Cr3+ ions was performed by yeast cells during the exponential growth phase, and with enriched amounts of 30–45 g/gd.m. of cells. Yeast biomass enriched with chromium ions was extracted with 0.1 mol/l NH4OH assuming that the extracts had the glucose tolerance factor (GTF). Then the extracts were passed through a gel-filtration column in order to isolate and purify the GTF. The presence of GTF in the purified fractions was determined by measuring the absorbance at 260 nm. It is evident from the obtained results that the added purified fractions enhanced the rates of CO2 production as well as the glucose utilization during alcoholic fermentation. As expected, the enhancement of both rates depended on the amounts of extracts added to the fermentation substrate. Thus, it is evident that purified extracts contained the GTF compound, and that Cr3+ ions were bonded to the protein molecule.

  3. Double shroud delivery of silica precursor for reducing hexavalent chromium in welding fume.

    Science.gov (United States)

    Wang, Jun; Kalivoda, Mark; Guan, Jianying; Theodore, Alexandros; Sharby, Jessica; Wu, Chang-Yu; Paulson, Kathleen; Es-Said, Omar

    2012-01-01

    The welding process yields a high concentration of nanoparticles loaded with hexavalent chromium (Cr(6+)), a known human carcinogen. Previous studies have demonstrated that using tetramethylsilane (TMS) as a shielding gas additive can significantly reduce the Cr(6+) concentration in welding fume particles. In this study, a novel insulated double shroud torch (IDST) was developed to further improve the reduction of airborne Cr(6+) concentration by separating the flows of the primary shielding gas and the TMS carrier gas. Welding fumes were collected from a welding chamber in the laboratory and from a fixed location near the welding arc in a welding facility. The Cr(6+) content was analyzed with ion chromatography and X-ray photoelectron spectroscopy (XPS). Results from the chamber sampling demonstrated that the addition of 3.2 ≈ 5.1% of TMS carrier gas to the primary shielding gas resulted in more than a 90% reduction of airborne Cr(6+) under all shielding gas flow rates. The XPS result confirmed complete elimination of Cr(6+) inside the amorphous silica shell. Adding 100 ≈ 1000 ppm of nitric oxide or carbon monoxide to the shielding gas could also reduce Cr(6+) concentrations up to 57% and 35%, respectively; however, these reducing agents created potential hazards from the release of unreacted agents. Results of the field test showed that the addition of 1.6% of TMS carrier gas to the primary shielding gas reduced Cr(6+) concentration to the limitation of detection (1.1 μg/m(3)). In a worst-case scenario, if TMS vapor leaked into the environment without decomposition and ventilation, the estimated TMS concentration in the condition of field sampling would be a maximum 5.7 ppm, still well below its flammability limit (1%). Based on a previously developed cost model, the use of TMS increases the general cost by 3.8%. No visual deterioration of weld quality caused by TMS was found, although further mechanical testing is necessary.

  4. Production of materials with alumina and ashes from incineration of chromium tanned leather shavings: environmental and technical aspects.

    Science.gov (United States)

    Basegio, T; Haas, C; Pokorny, A; Bernardes, A M; Bergmann, C P

    2006-09-21

    The leather tannery industry produces a significant amount of solid and hazardous wastes. Chromium-containing wastes like tanned shavings used to be incinerated in order to recover energy. The incineration process generates ashes that must be disposed of. This paper is a report on the results of the evaluation of technological properties and environmental compatibility of products made of alumina and ashes from incinerated chrome tanned shavings. The raw materials, tannery ashes and alumina were mixed together in different proportions. The ceramic bodies were molded using a hydraulic press and fired with a heating rate of 100 K/h until 1400 degrees C for 4 h in a muffle furnace. The ceramic specimens were characterized regarding physical, mechanical and thermal properties. Leaching tests, according to Brazilian, German and Dutch regulations, were performed on ceramic bodies containing different additions of ash. Results show that the ceramic materials produced are acceptable for refractory applications.

  5. Trivalent chromium removal from aqueous solutions by a sol–gel synthesized silica adsorbent functionalized with sulphonic acid groups

    Energy Technology Data Exchange (ETDEWEB)

    Gomez-Gonzalez, Sergio Efrain [Departamento de Ingeniería Química, Universidad de Guadalajara, Blvd. Marcelino García Barragán # 1421, esq. Calzada Olímpica, C.P. 44430 Guadalajara, Jalisco (Mexico); Carbajal-Arizaga, Gregorio Guadalupe [Departamento de Química, CUCEI, Universidad de Guadalajara, Blvd. Marcelino García Barragán # 1421, esq. Calzada Olímpica, C.P. 44430 Guadalajara, Jalisco (Mexico); Manriquez-Gonzalez, Ricardo [Departamento de Madera, Celulosa y Papel, CUCEI, Universidad de Guadalajara, Km 15.5, carretera Guadalajara-Nogales, Las Agujas, C.P. 45020 Zapopan, Jalisco (Mexico); De la Cruz-Hernandez, Wencel [Centro de Nanociencias y Nanotecnología, Universidad Nacional Autónoma de México, Km 107 carretera Tijuana-Ensenada, C.P. 22830 Ensenada, Baja California (Mexico); Gomez-Salazar, Sergio, E-mail: sergio.gomez@cucei.udg.mx [Departamento de Ingeniería Química, Universidad de Guadalajara, Blvd. Marcelino García Barragán # 1421, esq. Calzada Olímpica, C.P. 44430 Guadalajara, Jalisco (Mexico)

    2014-11-15

    Highlights: • Corpuscular sulphonic acid-functionalized silica holds improved uptake of chromium. • Mesopores on adsorbent facilitate (CH{sub 3}COO){sub 2}Cr{sup +} ion uptake on sulphonate sites. • Formation of chromium acetate sulphonate complex proposed from XPS results. • Fixed bed chromium uptake results suggest potential industrial use. - Abstract: A high capacity hybrid silica adsorbent was synthesized via sol–gel processing with sulphonic acid groups as trivalent chromium complex ions chelators from aqueous solutions. The synthesis included co-condensation of tetraethoxysilane (TEOS) with 3-(mercaptopropyl)trimethoxysilane (MPS), and oxidation of thiol to sulphonic acid groups. Chromium uptake kinetic, batch and fixed-bed experiments were performed to assess the removal of this metal from aqueous solutions. {sup 13}C, {sup 29}Si CPMAS NMR, FTIR, XPS were used to characterize the adsorbent structure and the nature of chromium complexes on the adsorbent surface. Chromium maximum uptake was obtained at pH 3 (72.8 mg/g). Elemental analysis results showed ligand density of 1.48 mmol sulphonic groups/g. About 407 mL of Cr(III) solution (311 mg/L) were treated to breakthrough point reaching ≤0.06 mg/L at the effluent. These results comply with USEPA regulation for chromium concentration in drinking water (≤0.1 mg/L). The adsorbent shows potential to be used in chromium separations to the industrial level.

  6. Study on the Cultivation of Chromium-enriched Yeast%富铬酵母的研制

    Institute of Scientific and Technical Information of China (English)

    王盛良; 黄杰; 黄薇; 孙桂菊

    2001-01-01

    This paper offered a method to get organic chromium nutrient bycultivating chromium-enriched yeast. It was found that the solution of low consistency promoted the growth of yeast, and with increasing the chromium concentration in culture,the chromium content of chromium-enriched yeast would increase. The solution of chromium-enriched and normal brewer' s yeast was measured by ultraviolet spectrometry with in 200~320nm wavelength range. A characteristic ultraviolet absorption peak appeared at 260nm. The organic chromium was about 97.6% of the total chromium in chromium-enriched yeast.%研究了富铬酵母的培养方法,发现培养基中低浓度的铬(<100mg/kg)对酵母生长起促进作用,且随着铬浓度的增加酵母对铬的富集作用亦增加。用200~320nm波长范围对富铬酵母及普通酵母溶液进行紫外扫描,发现在260nm处有一特征的吸收峰。富铬酵母中有机铬占总铬量的97.6%.

  7. Additives in yoghurt production

    Directory of Open Access Journals (Sweden)

    Milna Tudor

    2008-02-01

    Full Text Available In yoghurt production, mainly because of sensory characteristics, different types of additives are used. Each group, and also each substance from the same group has different characteristics and properties. For that reason, for improvement of yoghurt sensory characteristics apart from addition selection, the quantity of the additive is very important. The same substance added in optimal amount improves yoghurt sensory attributes, but too small or too big addition can reduce yoghurt sensory attributes. In this paper, characteristics and properties of mostly used additives in yoghurt production are described; skimmed milk powder, whey powder, concentrated whey powder, sugars and artificial sweeteners, fruits, stabilizers, casein powder, inulin and vitamins. Also the impact of each additive on sensory and physical properties of yoghurt, syneresis and viscosity, are described, depending on used amount added in yoghurt production.

  8. Quantification of total and hexavalent chromium in lager beers: variability between styles and estimation of daily intake of chromium from beer.

    Science.gov (United States)

    Vieira, Elsa; Soares, M Elisa; Kozior, Marta; Krejpcio, Zbigniew; Ferreira, Isabel M P L V O; Bastos, M Lourdes

    2014-09-17

    A survey of the presence of total and hexavalent chromium in lager beers was conducted to understand the variability between different styles of lager beer packaged in glass or cans and to estimate daily intake of total Cr and hexavalent chromium from beer. Graphite-furnace atomic absorption spectroscopy using validated methodologies was applied. Selective extraction of hexavalent chromium was performed using a Chromabond NH2/500 mg column and elution with nitric acid. The detection limits were 0.26 and 0.68 μg L(-1) for total Cr and Cr(VI), respectively. The mean content of total Cr ranged between 1.13 μg L(-1) in canned pale lager and 4.32 μg L(-1) in low-alcohol beers, whereas the mean content of Cr(VI) was beer, beer consumption can contribute approximately 2.28-8.64 and 1.6-6.17% of the recommended daily intake of chromium for women and men, respectively.

  9. Beneficial effect of chromium-rich yeast on glucose tolerance and blood lipids in elderly subjects.

    Science.gov (United States)

    Offenbacher, E G; Pi-Sunyer, F X

    1980-11-01

    Twenty-four volunteers, mean age 78, including eight mildly non-insulin-dependent diabetics, were randomly allocated to one of two groups and were fed (daily for 8 wk) 9 g of either chromium-rich brewers' yeast (experimental) or chromium-poor torula yeast (control). Before and after yeast supplementation, the serum glucose and insulin response to 100 g oral glucose was measured at 30 min intervals for 2 h. Fasting serum cholesterol, total lipids, and triglycerides were also determined. In the total experimental group (normals + diabetics) and in both the diabetic and nondiabetic experimental subgroups, glucose tolerance improved significantly and insulin output decreased after supplementation. Cholesterol and total lipids fell significantly after supplementation in the total experimental group. The cholesterol decrease was particularly marked in hypercholesterolemic subjects (cholesterol > 300 mg/dl). In the control group, no significant change in glucose tolerance, insulin, triglycerides, or total lipids was found. Cholesterol was significantly lowered in the nondiabetic but not in the diabetic group. Thus, chromium-rich brewers' yeast improved glucose tolerance and total lipids in elderly subjects, while chromium-poor torula yeast did not. An improvement in insulin sensitivity also occurred with brewers' yeast supplementation. This supports the thesis that elderly people may have a low level of chromium and that an effective source for chromium repletion, such as brewers' yeast, may improve their carbohydrate tolerance and total lipids. The improvement in serum cholesterol in some control subjects, as well as in the total experimental group, also suggests the presence of a hypocholesterolemic factor other than chromium in both brewers' and torula yeast.

  10. Influence of the chromium and ytterbium co-doping on the photoluminescence of zinc selenide crystals

    Institute of Scientific and Technical Information of China (English)

    I Radevici

    2014-01-01

    The luminescent properties of ZnSe, ZnSe:Cr (0.05 at.%Cr), ZnSe:Yb (0.03 at.%Yb) and ZnSe:Cr:Yb (0.05 at.%Cr, 0.05 at.%Yb) crystals, doped during the growth process by the chemical vapor transport method, were studied within the temperature in-terval of 6-300 K. At the 6 K temperature in the visible spectral range 2 bands were observed:a band in the excitonic spectral region and a band of self-activated luminescence. It was shown that co-doping of zinc selenide crystals with the chromium and ytterbium led to the combination of the impurities influence on the photoluminescent properties. At the liquid helium temperature in the middle in-frared range of the spectra of the ytterbium and chromium co-doped crystal a band with the maximum localized at 1.7 µm was ob-served, which was overlapped with a complex band in the middle-IR spectral range, characteristic for the chromium doped ZnSe crys-tals. On the basis of obtained data an interaction mechanism of the chromium and ytterbium co-doping impurities was proposed. Guided by the existent model of the ytterbium ion incorporation in the selenide sublattice of the ZnSe crystals, an assumption about stabilization of single charged chromium ions in the zinc sublattice crystal nodes, by means of formation of the local charge compen-sating clusters, was made. It was assumed that the resonant energy transfer from one chromium ion to another, which led to the con-centration quenching of the IR emission in the ZnSe:Cr PL spectra, would lead to the broadening of the IR emission in the spectra of ytterbium and chromium co-doped zinc selenide crystals.

  11. Photocatalysis with chromium-doped TiO2: Bulk and surface doping

    KAUST Repository

    Ould-Chikh, Samy

    2014-04-15

    The photocatalytic properties of TiO2 modified by chromium are usually found to depend strongly on the preparation method. To clarify this problem, two series of chromium-doped titania with a chromium content of up to 1.56 wt % have been prepared under hydrothermal conditions: the first series (Cr:TiO2) is intended to dope the bulk of TiO2, whereas the second series (Cr/TiO2) is intended to load the surface of TiO2 with Cr. The catalytic properties have been compared in the photocatalytic oxidation of formic acid. Characterization data provides evidence that in the Cr/TiO2 catalysts chromium is located on the surface of TiO2 as amorphous CrOOH clusters. In contrast, in the Cr:TiO 2 series, chromium is mostly dissolved in the titania lattice, although a minor part is still present on the surface. Photocatalytic tests show that both series of chromium-doped titania demonstrate visible-light-driven photo-oxidation activity. Surface-doped Cr/TiO2 solids appear to be more efficient photocatalysts than the bulk-doped Cr:TiO2 counterparts. It\\'s classified! The photocatalytic properties of TiO2 modified by chromium depend strongly on the preparation method. To clarify this problem, two types of modified titania are discussed: one with CrIII doped in the bulk and one with CrOOH clusters on the TiO2 surface (see picture). Both series show visible-light-driven photo-oxidation activity. However, surface modification appears to be a more efficient strategy. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. Selective and sensitive detection of chromium(VI) in waters using electrospray ionization mass spectrometry.

    Science.gov (United States)

    Weldy, Effie; Wolff, Chloe; Miao, Zhixin; Chen, Hao

    2013-09-01

    From 2000 through 2011, there were 14 criminal cases of violations of the Clean Water Act involving the discharge of chromium, a toxic heavy metal, into drinking and surface water sources. As chromium(VI), a potential carcinogen present in the environment, represents a significant safety concern, it is currently the subject of an EPA health risk assessment. Therefore, sensitive and selective detection of this species is highly desired. This study reports the analysis of chromium(VI) in water samples by electrospray ionization mass spectrometry (ESI-MS) following its reduction and complexation with ammonium pyrrolidinedithiocarbamate (APDC). The reduction and subsequent complexation produce a characteristic [Cr(III)O]-PDC complex which can be detected as a protonated ion of m/z 507 in the positive ion mode. The detection is selective to chromium(VI) under acidic pH, even in the presence of chromium(III) and other metal ions, providing high specificity. Different water samples were examined, including deionized, tap, and river waters, and sensitive detection was achieved. In the case of deionized water, quantification over the concentration range of 3.7 to 148ppb gave an excellent correlation coefficient of 0.9904 using the enhanced MS mode scan. Using the single-reaction monitoring (SRM) mode (monitoring the characteristic fragmentation of m/z 507 to m/z 360), the limit of detection (LOD) was found to be 0.25ppb. The LOD of chromium(VI) for both tap and river water samples was determined to be 2.0ppb. A preconcentration strategy using simple vacuum evaporation of the aqueous sample was shown to further improve the ESI signal by 15 fold. This method, with high sensitivity and selectivity, should provide a timely solution for the real-world analysis of toxic chromium(VI).

  13. Wire + Arc Additive Manufacturing

    OpenAIRE

    Williams, Stewart W.; Martina, Filomeno; Addison, Adrian C.; Ding, Jialuo; Pardal, Goncalo; Colegrove, Paul A.

    2016-01-01

    Depositing large components (>10 kg) in titanium, aluminium, steel and other metals is possible using Wire + Arc Additive Manufacturing. This technology adopts arc welding tools and wire as feedstock for additive manufacturing purposes. High deposition rates, low material and equipment costs, and good structural integrity make Wire+Arc Additive Manufacturing a suitable candidate for replacing the current method of manufacturing from solid billets or large forgings, especially with regards to ...

  14. Pressure-driven formation and stabilization of superconductive chromium hydrides

    Science.gov (United States)

    Yu, Shuyin; Jia, Xiaojing; Frapper, Gilles; Li, Duan; Oganov, Artem R.; Zeng, Qingfeng; Zhang, Litong

    2015-01-01

    Chromium hydride is a prototype stoichiometric transition metal hydride. The phase diagram of Cr-H system at high pressures remains largely unexplored due to the challenges in dealing with the high activation barriers and complications in handing hydrogen under pressure. We have performed an extensive structural study on Cr-H system at pressure range 0 ∼ 300 GPa using an unbiased structure prediction method based on evolutionary algorithm. Upon compression, a number of hydrides are predicted to become stable in the excess hydrogen environment and these have compositions of Cr2Hn (n = 2–4, 6, 8, 16). Cr2H3, CrH2 and Cr2H5 structures are versions of the perfect anti-NiAs-type CrH with ordered tetrahedral interstitial sites filled by H atoms. CrH3 and CrH4 exhibit host-guest structural characteristics. In CrH8, H2 units are also identified. Our study unravels that CrH is a superconductor at atmospheric pressure with an estimated transition temperature (T c) of 10.6 K, and superconductivity in CrH3 is enhanced by the metallic hydrogen sublattice with T c of 37.1 K at 81 GPa, very similar to the extensively studied MgB2. PMID:26626579

  15. Chromium Extraction from Sewage Sludge Using Polyepoxysuccinic Acid

    Institute of Scientific and Technical Information of China (English)

    ZHANG Li-Hua; ZHU Zhi-Liang

    2012-01-01

    An environmentally benign biodegradable chelant,polyepoxysuccinic acid (PESA),was used to separate heavy metals from sewage sludge from the Shanghai Taopu Wastewater Treatment Plant,China,based on chemical extraction technology.The extraction of chromium (Cr) from sewage sludge with an aqueous solution of PESA was studied under various conditions.It was found that the extraction of Cr using PESA was more efficient than that using ethylenediaminetetraacetic acid (EDTA) and S,S-ethylenediaminedisuccinic acid (EDDS) under similar conditions.PESA was capable of extracting Cr from the sewage sludge,and the extraction efficiency was obviously dependent on both the pH and the concentration of the chelating reagent.The extraction efficiency decreased gradually with increasing pH,and the dependence on pH decreased as the concentration of PESA increased.The extraction efficiency reached 58% under conditions of pH =4 and a ratio of PESA to total heavy metals of 10∶1.The extraction efficiency was maintained above 40% within the pH range from 1 to 7 at the high ratio of PESA to total heavy metals of 10∶1.Comparing the contents of heavy metals in the sewage sludge before and after the extraction,it was found that the extracted Cr came mainly from the reducible and oxidizable fractions.

  16. Inhibition by chromium and cadmium of anaerobic acidogenesis.

    Science.gov (United States)

    Yu, H Q; Fang, H H

    2001-01-01

    The effects of chromium (III) and cadmium on the anaerobic acidogenesis of a simulated dairy waste were examined using serum vials. At Cd dosages less than 20 mg/l, the acidogenesis process was enhanced by the dosage, resulting in a higher degree of acidification, protein conversion, and hydrogen production than the control. At dosages over 20-mg/l, Cd inhibited the acidogenesis. The Cr (III) dosage of 5 mg/l reduced overall volatile fatty acid and alcohol generation, degree of acidification, conversions of lactose, lipid and protein, and total biogas production, with the exception of accumulation of hydrogen and propionate. At dosages exceeding 5 mg/l, Cr (III) had a severe inhibition on the acidogenesis. The Cd concentrations which caused a 50% reduction in total volatile fatty acid and alcohol production, degree of acidification and cumulative gas production were higher than the corresponding values caused by Cr (III), suggesting that Cr (III) was more toxic to acidogenic bacteria than Cd.

  17. Enhanced chromium adsorption capacity via plasma modification of natural zeolites

    Science.gov (United States)

    Cagomoc, Charisse Marie D.; Vasquez, Magdaleno R., Jr.

    2017-01-01

    Natural zeolites such as mordenite are excellent adsorbents for heavy metals. To enhance the adsorption capacity of zeolite, sodium-exchanged samples were irradiated with 13.56 MHz capacitively coupled radio frequency (RF) argon gas discharge. Hexavalent chromium [Cr(VI)] was used as the test heavy metal. Pristine and plasma-treated zeolite samples were soaked in 50 mg/L Cr solution and the amount of adsorbed Cr(VI) on the zeolites was calculated at predetermined time intervals. Compared with untreated zeolite samples, initial Cr(VI) uptake was 70% higher for plasma-treated zeolite granules (50 W 30 min) after 1 h of soaking. After 24 h, all plasma-treated zeolites showed increased Cr(VI) uptake. For a 2- to 4-month period, Cr(VI) uptake increased about 130% compared with untreated zeolite granules. X-ray diffraction analyses between untreated and treated zeolite samples revealed no major difference in terms of its crystal structure. However, for plasma-treated samples, an increase in the number of surface defects was observed from scanning electron microscopy images. This increase in the number of surface defects induced by plasma exposure played a crucial role in increasing the number of active sorption sites on the zeolite surface.

  18. Adsorption of chromium ion (VI by acid activated carbon

    Directory of Open Access Journals (Sweden)

    A. A. Attia

    2010-03-01

    Full Text Available The activated carbon produced from olive stones was chemically activated using sulfuric acid, (OS-S, and utilized as an adsorbent for the removal of Cr(VI from aqueous solution in the concentration range 4-50 mg/L. Adsorption experiments were carried out in a batch process and various experimental parameters such as effect of contact time, initial chromium ion concentration, carbon dosage, and pH on percentage removal have been studied. Adsorption results obtained for activated carbon (OS-S were compared with the acid-treated commercial activated carbon (CAC-S. The optimum efficiency shows that the Cr(VI uptake being attained at pH 1.5. The equilibrium adsorption data was better fitted to the Langmuir adsorption model. The results of kinetic models showed that the pseudo-first-order kinetic model was found to correlate the experimental data well. It was concluded that activated carbon produced from olive stones (OS-S has an efficient adsorption capacity compared to (CAC-S sample.

  19. Microstructure Evolution and Grain Growth Kinetics in Annealed Nanocrystalline Chromium

    Energy Technology Data Exchange (ETDEWEB)

    Chojnowski, Grzegorz [Warsaw University; Przenioslo, Radoslaw [Warsaw University; Sosnowska, Izabela [Warsaw University; Bukowski, Mirko [University of Saarbrucken, Saarbrucken, Germany; Natter, Harald [University of Saarbrucken, Saarbrucken, Germany; Hempelmann, Rolf [University of Saarbrucken, Saarbrucken, Germany; Fitch, Andrew [European Synchrotron Radiation Facility (ESRF); Urban, Volker S [ORNL

    2007-01-01

    The kinetics of thermal evolution of the microstructure of nanocrystalline chromium (nano-Cr) has been studied by time-resolved synchrotron radiation techniques: high-resolution powder diffraction and small-angle X-ray scattering (SAXS). The as-prepared electrodeposited nano-Cr with average grain size of 27 nm shows the same bcc structure as {alpha}-Cr. The nano-Cr cubic lattice parameter thermal expansion is the same as that of reference polycrystalline {alpha}-Cr. Annealing of nano-Cr at temperatures above 400 C leads to a grain growth process with the final grain size not exceeding 125 nm even at a temperature of 700 C. The single power-law behavior is observed by SAXS in as-prepared nano-Cr changes during annealing above 400 C. In nano-Cr samples annealed at temperatures between 400 and 700 C, the low-q part of the SAXS signal shows a Porod-type behavior while the high-q part shows a power-law Q-{alpha} with the exponent {alpha} < 4. This effect is probably due to changes of the grain surface roughness during grain growth.

  20. Elementary surface processes during reactive magnetron sputtering of chromium

    Energy Technology Data Exchange (ETDEWEB)

    Monje, Sascha; Corbella, Carles, E-mail: carles.corbella@rub.de; Keudell, Achim von [Research Group Reactive Plasmas, Ruhr-University Bochum, Universitystr. 150, 44801 Bochum (Germany)

    2015-10-07

    The elementary surface processes occurring on chromium targets exposed to reactive plasmas have been mimicked in beam experiments by using quantified fluxes of Ar ions (400–800 eV) and oxygen atoms and molecules. For this, quartz crystal microbalances were previously coated with Cr thin films by means of high-power pulsed magnetron sputtering. The measured growth and etching rates were fitted by flux balance equations, which provided sputter yields of around 0.05 for the compound phase and a sticking coefficient of O{sub 2} of 0.38 on the bare Cr surface. Further fitted parameters were the oxygen implantation efficiency and the density of oxidation sites at the surface. The increase in site density with a factor 4 at early phases of reactive sputtering is identified as a relevant mechanism of Cr oxidation. This ion-enhanced oxygen uptake can be attributed to Cr surface roughening and knock-on implantation of oxygen atoms deeper into the target. This work, besides providing fundamental data to control oxidation state of Cr targets, shows that the extended Berg's model constitutes a robust set of rate equations suitable to describe reactive magnetron sputtering of metals.

  1. Chromium Diffusion Doping on ZnSe Crystals

    Science.gov (United States)

    Journigan, Troy D.; Chen, K.-T.; Chen, H.; Burger, A.; Schaffers, K.; Page, R. H.; Payne, S. A.

    1997-01-01

    Chromium doped zinc selenide crystal have recently been demonstrated to be a promising material for near-IR room temperature tunable lasers which have an emission range of 2-3 micrometers. In this study a new diffusion doping process has been developed for incorporation of Cr(+2) ion into ZnSe wafers. This process has been successfully performed under isothermal conditions, at temperatures above 800 C. Concentrations in excess of 10(exp 19) Cr(+2) ions/cu cm, an order of magnitude larger than previously reported in melt grown ZnSe material, have been obtained by diffusion doping, as estimated from optical absorption measurements. The diffusivity was estimated to be about 10(exp -8) sq cm/sec using a thin film diffusion model. Resistivity was derived from current-voltage measurements and in the range of 10(exp 13) and 10(exp 16) omega-cm. The emission spectra and temperature dependent lifetime data will also be presented and discussed.

  2. Extractive removal of chromium (VI) from industrial waste solution.

    Science.gov (United States)

    Agrawal, Archana; Pal, Chandana; Sahu, K K

    2008-11-30

    Extractive removal of Cr (VI) was carried out from chloride solutions using cyanex 923 mixed with kerosene. The efficiency of this extractant was studied under various experimental conditions, such as concentration of different mineral acids in the aqueous phase, concentration of cyanex 923 and Cr (VI) present in the initial aqueous feed, temperature and time of extraction, organic to aqueous (O/A) phase ratio. Percentage Cr (VI) extraction decreases with the increase in temperature at varying concentration of cyanex 923. The interference of the impurities usually associated with Cr (VI) such as Cr (III), Cu, Ni, Fe (II), Zn, Chloride and sulphate, etc., were examined under the optimized conditions and only Zn was found to interfere. Under the optimum experimental conditions 98.6-99.9% of Cr (VI) was extracted in 3-5 min at O/A of 2 with the initial feed concentration of 1g/L of Cr (VI). The extracted Cr (VI) was quantitatively stripped with 1M NaOH and the organic phase obtained after the stripping of Cr (VI) was washed with dilute HCl solution to neutralize any NaOH trapped/adhered to the solvent and then with distilled water. This regenerated solvent was reused in succeeding extraction of chromium (VI). Finally a few experiments were performed with the synthetic effluent from an electroplating industry.

  3. Probing neutrino nature at Borexino detector with chromium neutrino source

    CERN Document Server

    Sobków, W

    2016-01-01

    In this paper, we indicate a possibility of utilizing the intense chromium source ($\\sim 370 PBq$) in probing the neutrino nature in low energy neutrino experiments with the ultra-low threshold and background real-time Borexino detector located near the source ($\\sim 8 m$). We analyze the elastic scattering of electron neutrinos (Dirac or Majorana, respectively) on the unpolarized electrons in the relativistic neutrino limit. We assume that the incoming neutrino beam is the superposition of left-right chiral states. Left chiral neutrinos may be detected by the standard $V A$ and non-standard scalar $S_L$, tensor $T_L$ interactions, while right chiral ones partake only in the exotic $V + A$ and $S_R, T_R$ interactions. Our model-independent study is carried out for the flavour (current) neutrino eigenstates. We compute the expected event number for the standard $V-A$ interaction of the left chiral neutrinos using the current experimental values of standard couplings and in the case of left-right chiral superpo...

  4. Distribution of chromium contamination and microbial activity in soil aggregates.

    Science.gov (United States)

    Tokunaga, Tetsu K; Wan, Jiamin; Hazen, Terry C; Schwartz, Egbert; Firestone, Mary K; Sutton, Stephen R; Newville, Matthew; Olson, Keith R; Lanzirotti, Antonio; Rao, William

    2003-01-01

    Biogeochemical transformations of redox-sensitive chemicals in soils can be strongly transport-controlled and localized. This was tested through experiments on chromium diffusion and reduction in soil aggregates that were exposed to chromate solutions. Reduction of soluble Cr(VI) to insoluble Cr(II) occurred only within the surface layer of aggregates with higher available organic carbon and higher microbial respiration. Sharply terminated Cr diffusion fronts develop when the reduction rate increases rapidly with depth. The final state of such aggregates consists of a Cr-contaminated exterior, and an uncontaminated core, each having different microbial community compositions and activity. Microbial activity was significantly higher in the more reducing soils, while total microbial biomass was similar in all of the soils. The small fraction of Cr(VI) remaining unreduced resides along external surfaces of aggregates, leaving it potentially available to future transport down the soil profile. Using the Thiele modulus, Cr(VI) reduction in soil aggregates is shown to be diffusion rate- and reaction rate-limited in anaerobic and aerobic aggregates, respectively. Thus, spatially resolved chemical and microbiological measurements are necessary within anaerobic soil aggregates to characterize and predict the fate of Cr contamination. Typical methods of soil sampling and analyses that average over redox gradients within aggregates can erase important biogeochemical spatial relations necessary for understanding these environments.

  5. Characterization of Two ODS Alloys: Chromium-18 ODS and Chromium-9 ODS

    Science.gov (United States)

    Goddard, Julianne

    ODS alloys, or oxide dispersion strengthened alloys, are made from elemental or pre-alloyed metal powders mechanically alloyed with oxide powders in a high-energy attributor mill, and then consolidated by either hot isostatic pressing or hot extrusion causing the production of nanometer scale oxide and carbide particles within the alloy matrix; crystalline properties such as creep strength, ductility, corrosion resistance, tensile strength, swelling resistance, and resistance to embrittlement are all observed to be improved by the presence of nanoparticles in the matrix. The presented research uses various methods to observe and characterize the microstructural and microchemical properties of two experimental ODS alloys, 18Cr ODS and 9Cr ODS. The results found aid in assessing the influence of chemical and structural variations on the effectiveness of the alloy, and further aid in the optimization of these advanced alloys for future use in nuclear cladding and structural applications in Generation IV nuclear reactors. Characterization of these alloys has been conducted in order to identify the second-phase small precipitates through FESEM, TEM, EDS, Synchrotron X-ray diffraction analysis, and CuKalpha XRD analysis of bulk samples and of nanoparticles after extraction from the alloy matrix. Comparison of results from these methods allows further substantiation of the accuracy of observed nanoparticle composition and identification. Also, TEM samples of the two alloys have been irradiated in-situ with 1 MeV Kr and 300 keV Fe ions to various doses and temperatures at the IVEM-Tandem TEM at Argonne National Laboratory and post-irradiated characterization has been conducted and compared to the pre-irradiated characterization results in order to observe the microstructural and microchemical evolution of nanoparticles under irradiation. Overall in the as-received state, the initial Y2O3 is not found anymore and in addition to oxide particles the alloys contain carbides

  6. Polylactides in additive biomanufacturing.

    Science.gov (United States)

    Poh, Patrina S P; Chhaya, Mohit P; Wunner, Felix M; De-Juan-Pardo, Elena M; Schilling, Arndt F; Schantz, Jan-Thorsten; van Griensven, Martijn; Hutmacher, Dietmar W

    2016-12-15

    New advanced manufacturing technologies under the alias of additive biomanufacturing allow the design and fabrication of a range of products from pre-operative models, cutting guides and medical devices to scaffolds. The process of printing in 3 dimensions of cells, extracellular matrix (ECM) and biomaterials (bioinks, powders, etc.) to generate in vitro and/or in vivo tissue analogue structures has been termed bioprinting. To further advance in additive biomanufacturing, there are many aspects that we can learn from the wider additive manufacturing (AM) industry, which have progressed tremendously since its introduction into the manufacturing sector. First, this review gives an overview of additive manufacturing and both industry and academia efforts in addressing specific challenges in the AM technologies to drive toward AM-enabled industrial revolution. After which, considerations of poly(lactides) as a biomaterial in additive biomanufacturing are discussed. Challenges in wider additive biomanufacturing field are discussed in terms of (a) biomaterials; (b) computer-aided design, engineering and manufacturing; (c) AM and additive biomanufacturing printers hardware; and (d) system integration. Finally, the outlook for additive biomanufacturing was discussed.

  7. Additive Gaussian Processes

    CERN Document Server

    Duvenaud, David; Rasmussen, Carl Edward

    2011-01-01

    We introduce a Gaussian process model of functions which are additive. An additive function is one which decomposes into a sum of low-dimensional functions, each depending on only a subset of the input variables. Additive GPs generalize both Generalized Additive Models, and the standard GP models which use squared-exponential kernels. Hyperparameter learning in this model can be seen as Bayesian Hierarchical Kernel Learning (HKL). We introduce an expressive but tractable parameterization of the kernel function, which allows efficient evaluation of all input interaction terms, whose number is exponential in the input dimension. The additional structure discoverable by this model results in increased interpretability, as well as state-of-the-art predictive power in regression tasks.

  8. Effect of Chromium Supplementation on Element Distribution in a Mouse Model of Polycystic Ovary Syndrome.

    Science.gov (United States)

    Chen, Tsung-Sheng; Chen, Yi-Ting; Liu, Chia-Hsin; Sun, Chi-Ching; Mao, Frank Chiahung

    2015-12-01

    Polycystic ovary syndrome (PCOS) is a complex endocrine disorder and one of the most common causes of anovulatory infertility. In addition, insulin resistance is commonly associated with PCOS and contributed to pathophysiology connected to dietary minerals including chromium (Cr), copper (Cu), iron (Fe), and zinc (Zn). The aims of this study were to explore whether PCOS in mice alters levels of these elements and determine if Cr supplementation resolves changes. Twenty-four female BALB/c mice were divided into three groups of eight mice [normal control (NC), PCOS+placebo milk (PP), and PCOS+Cr-containing milk (PCr)]. Each group received a high-fat diet for 4 weeks. Our results show significantly higher levels of dehydroepiandrosterone (DHEA) (p<0.001), fasting glucose (p<0.05), and fasting insulin (p<0.05) in the PP group compared with both NC and PCr group. However, Cr levels were significantly lower in muscle, bone, and serum in the PP group (p<0.05) compared with NC and PCr groups. In liver, bone, and serum, Fe levels were significantly higher in the PP group compared with the NC group (p<0.05). In addition, we found significant correlations between Cu/Zn ratio and fasting insulin in all mice (r=0.61; p=0.002). Given that significant research shows that Cr supplementation improves fasting glucose, fasting insulin, and metal metabolism disorders for PCOS mice, our data suggest that trace element levels can serve as biomarkers to prescribe therapeutic supplementation to maintain a healthy metabolic balance and treat disease conditions.

  9. Microbeam x-ray absorption spectroscopy study of chromium in large-grain uranium dioxide fuel

    Science.gov (United States)

    Mieszczynski, C.; Kuri, G.; Bertsch, J.; Martin, M.; Borca, C. N.; Delafoy, Ch; Simoni, E.

    2014-09-01

    Synchrotron-based microprobe x-ray absorption spectroscopy (XAS) has been used to study the local atomic structure of chromium in chromia-doped uranium dioxide (UO2) grains. The specimens investigated were a commercial grade chromia-doped UO2 fresh fuel pellet, and materials from a spent fuel pellet of the same batch, irradiated with an average burnup of ~40 MW d kg-1. Uranium L3-edge and chromium K-edge XAS have been measured, and the structural environments of central uranium and chromium atoms have been elucidated. The Fourier transform of uranium L3-edge extended x-ray absorption fine structure shows two well-defined peaks of U-O and U-U bonds at average distances of 2.36 and 3.83 Å. Their coordination numbers are determined as 8 and 11, respectively. The chromium Fourier transform extended x-ray absorption fine structure of the pristine UO2 matrix shows similar structural features with the corresponding spectrum of the irradiated spent fuel, indicative of analogous chromium environments in the two samples studied. From the chromium XAS experimental data, detectable next neighbor atoms are oxygen and uranium of the cation-substituted UO2 lattice, and two distinct subshells of chromium and oxygen neighbors, possibly because of undissolved chromia particles present in the doped fuels. Curve-fitting analyses using theoretical amplitude and phase-shift functions of the closest Cr-O shell and calculations with ab initio computer code FEFF and atomic clusters generated from the chromium-dissolved UO2 structure have been carried out. There is a prominent reduction in the length of the adjacent Cr-O bond of about 0.3 Å in chromia-doped UO2 compared with the ideal U-O bond length in standard UO2 that would be expected because of the change in effective Coulomb interactions resulting from replacing U4+ with Cr3+ and their ionic size differences. The contraction of shortest Cr-U bond is ~0.1 Å relative to the U-U bond length in bulk UO2. The difference in the

  10. Hard Chromium Electroplating and Improvement the Properties by the Thermo Chemical Treatments (Solid Carburizing of Low Carbon Steel

    Directory of Open Access Journals (Sweden)

    Ahmed Salloum Abbas

    2009-01-01

    Full Text Available In this research the hard chromium electroplating process, which is one of the common methods of overlay coating was used, by using chromium acid as source of chromium and sulphuric acid as catalyst since the ratio between chromic acid and sulphuric acid is (100 : 1 consequently. Plating process was made by applying current of density (40 Amp / dm2 and the range of solution temperature was (50 – 55oC with different time periods (1-5 hr. A low carbon steel type (Ck15 was used as substrate for hard chromium electroplating. Solid carburization was carried out for hard chromium plating specimen at temperature (925oC with time duration (2 hr to be followed with quenching and tempering. The phase analysis was conducted by using X– ray diffraction. The examination results show that the chromium carbides in plating layer were (Cr23C6, Cr7C3. The microhardness of hard chromium plating specimen was measured, and the results show that the high hardness was about (907HV. After solid carburization the hardness values increase and the results show that the higher hardness for chromium plating layer on low carbon steel surface was (1276 HV. Wear apparatus type (Pin on Disc was used to study dry sliding wear properties of low carbon steel (As received and hard chromium plating specimens and solid carburized. The effect of applied normal load on wear rate was studied with weighting method using five normal loads (5, 10, 15, 20, 25 N at constant sliding speed (2.198 m / sec. The results reveal that the wear rate increases with the increasing of applied normal load. A good improvement in wear resistance was noticed for hard chromium plating specimens as compared with substrate specimen. It was also seen that, the improvement in wear resistance was (94% as compared with substrate metal when carburizing treatment is carried out on hard chromium plating specimens.

  11. Effects of Single and Combinative Pollutions of Lead, Cadmium and Chromium on the Germination of Brassica chinensis L.%铅、镉、铬单一和复合污染对青菜种子萌发的生物学效应

    Institute of Scientific and Technical Information of China (English)

    任安芝; 高玉葆

    2000-01-01

    Germiantion of Bra.s.sica chinensis L. grown in the solution with different concentrations of lead, cadmium and chromium (single and combinative) was investigated. Root lengths decreased with the increase of lead, cadmium and chromium in hydroponic solution. The physiological toxicity order for these three ions was Cr6+>Cd2+>Pb2 +. The uptake of Pb by Bras.sica chinensis was enhanced with Pb addition. The toxicity of Cr and Pb was reduced due to precipitation of Cr2O72- and Pb2+ .The toxicity of Cd to plant decreased when Cr6+ was added.

  12. Simultaneously Recovering High-Purity Chromium and Removing Organic Pollutants from Tannery Effluent

    Directory of Open Access Journals (Sweden)

    Jie Zong

    2016-01-01

    Full Text Available Chromium pollution is a serious issue because of carcinogenic toxicities of the pollutants and low recovery rate of chromium because of the presence of organic, such as protein and fat. In this work, high recovery rate and high purity of the chromium ion were successfully prepared by the way of acid enzyme, flocculant, and Fenton oxidation. The experiments were characterized by TG, TOC, UV-VIS, and SEM. In the work, the tannery waste chrome liquor was used as experimental material. The results showed that the percentage of reduction of TOC in the tannery waste chrome liquor by method of Fenton oxidation, acid enzyme, and the flocculant was 71.15%, 65.26%, and 22.05%, respectively. Therefore, the organism content of chrome tanning waste liquid was greatly reduced through the pretreatment. And the application experiment showed that the properties and grain surface and fibers of the tanned leather with commercial chromium powder and chrome tanning agent prepared from the chromium waste liquid treated with Fenton are nearly the same.

  13. Thermodynamics of chromium in UO{sub 2} fuel: A solubility model

    Energy Technology Data Exchange (ETDEWEB)

    Riglet-Martial, Ch., E-mail: chantal.martial@cea.fr [Commissariat à l’Energie Atomique et aux Energies Alternatives, Direction de l’Energie Nucléaire, Département d’Etudes des Combustibles, Centre d’Etudes de Cadarache, 13108 Saint-Paul-lez-Durance Cedex (France); Martin, Ph. [Commissariat à l’Energie Atomique et aux Energies Alternatives, Direction de l’Energie Nucléaire, Département d’Etudes des Combustibles, Centre d’Etudes de Cadarache, 13108 Saint-Paul-lez-Durance Cedex (France); Testemale, D. [Université Grenoble Alpes, Institut NEEL, F-38042 Grenoble (France); CNRS, Institut NEEL, F-38042 Grenoble (France); Sabathier-Devals, C.; Carlot, G.; Matheron, P.; Iltis, X.; Pasquet, U.; Valot, C. [Commissariat à l’Energie Atomique et aux Energies Alternatives, Direction de l’Energie Nucléaire, Département d’Etudes des Combustibles, Centre d’Etudes de Cadarache, 13108 Saint-Paul-lez-Durance Cedex (France); Delafoy, C. [AREVA NP SAS, 10 rue Juliette Recamier, 69456 Lyon Cedex 06 (France); Largenton, R. [EDF R and D, Mechanics and Material Component Department, Avenue des Renardières, 77818 Moret sur Loing Cedex (France)

    2014-04-01

    The solubility and speciation of chromium in doped uranium oxide are measured in carefully controlled temperature and oxygen potential conditions using electron probe microanalysis (EPMA) and scanning electron spectroscopy (SEM). The examination of the samples by X-ray Absorption Spectroscopy (XAS) provides evidence that (i) chromium is soluble in the UO{sub 2} matrix under the +3 oxidation state only regardless of the sintering conditions which is in accordance with a soluble species of type CrO{sub 3/2} and (ii) soluble chromium exhibits octahedral symmetry with 6 atoms of oxygen forming CrO{sub 6} patterns in the UO{sub 2} structure. In consistency with all available experimental information including previously published data, the solubility of chromium in UO{sub 2} corresponding to each two-phase field with either Cr, CrO and Cr{sub 2}O{sub 3} may be described in the ranges 1500 °C < T < 2000 °C and −460 < μ{sub O2} < −360 kJ/mol using the standard thermodynamic equations governing solubility equilibria. The characteristic parameters of the solubility laws in UO{sub 2} for the three chromium phases are derived.

  14. Competition of Chromium on Iron binding sites in the biological system

    Directory of Open Access Journals (Sweden)

    *F. S. Rehmani

    2011-09-01

    Full Text Available Hexavalent chromium is mutagenic and neurotoxic. Trivalent Chromium is involved in the enzymes of glucose metabolism. Chromium is generally found in +3 oxidation state and sometimes it competes for the binding sites of iron in the biological system, when the concentration of chromium exceeds above the normal, it inhibits the absorption of iron and iron deficiency leads diseases such as anemia, tinnitus and depression. Salicylicdhydroxamic acid a hydroxamate type siderophore is used as a drug in the chelation therapy of iron overload patients. The complex formation of Cr(III and Fe(III with salicyclic hydroxamate were studied potentiometrically at different temperatures and data was subjected to computer programs. The stability constant (log beta values and thermodynamic stabilities were calculated. It was found that salicyclic hydroxamate forms 1:1 complex at pH 3 and 1:2 complex at pH 4 with Cr(III and Fe(III, respectively. The stability constant (Log beta and thermodynamic stabilities of Cr(III Salicyclic hydroxamate complexes are close to Fe(III Salicyclic hydroxamate complexes. It was observed from the stability constant values that after chelating therapy the concentration of chromium become low and deficiency symptoms appear resulting diabetes.

  15. REMOVAL OF CHROMIUM FROM AQUEOUS SOLUTION USING LOCALLY AVAILABLE INEXPENSIVE TARO AND WATER HYACINTH AS BIOSORBENT

    Directory of Open Access Journals (Sweden)

    Shahjalal Khandaker

    2016-04-01

    Full Text Available In this investigation, locally available and inexpensive Taro and Water Hyacinth were used as biosorbents to remove chromium from synthetic wastewater. The removal of this metal ion from water in the batch and column method have been studied and discussed. Adsorption kinetics and equilibrium isotherm studies were also carried out. The material exhibits good adsorption capacity and the data follow both Freundlich and Langmuir models. Scanning Electronic Microscopic image was also used to understand the surface characteristics of biosorbent before and after biosorption studies. Effects of various factors such as pH, adsorbent dose, adsorbate initial concentration, particle size etc. were analyzed. The initial concentrations of chromium were considered 5-30mgL-1 in batch method and only 4mgL-1 in column method. The maximum chromium adsorbed was 1.64 mgg-1 and 4.44 mgg-1 in Batch method and 1.15 mgg-1 and 0.75 mgg-1 in Column method. Batch and Column desorption and regeneration studies were conducted. Column desorption studies indicated that both of these biosorbents could be reused for removing heavy metals. Results of the laboratory experiments show that the performance of Taro and Water Hyacinth prove that they can effectively be used as low cost biosorbents for the removal of chromium from wastewater.KEYWORDS:   adsorption; chromium removal; Taro; water hyacinth; batch method; column studies

  16. Sodium corrosion behavior of austenitic alloys and selective dissolution of chromium and nickel

    Science.gov (United States)

    Suzuki, T.; Mutoh, I.; Yagi, T.; Ikenaga, Y.

    1986-06-01

    The corrosion behavior of six austenitic alloys and reference Type 316 stainless steel (SS) has been examined in a flowing sodium environment at 700°C for up to about 4000 h. The alloys with a range of nickel content between ~ 15 and 43 wt% were designed and manufactured with an expectation of improved swelling resistance during fast neutron irradiation, compared to reference Type 316 SS. The corrosion loss of the alloys at zero downstream position and the concentrations of chromium, nickel and iron in the surface region were determined as a function of corrosion time. The selective dissolution of nickel and chromium played an important role in sodium corrosion of the alloys. During the initial period, accelerated corrosion took place and selective dissolution of chromium and nickel proceeded at a rapid rate. During the subsequent period, the overall corrosion rate and depletion of chromium and nickel decreased with increasing time until the corrosion rate and the surface concentrations of chromium, nickel and iron, which depended on composition of the alloys, reached the steady-state after about 2000 h. Also, the corrosion rate increased with increasing original nickel content of the alloys. Microstructural examination revealed surface attack of the alloys with higher nickel contents, in particular for the two precipitation strengthened Fe-Ni alloys. The alloys showed a trend of increasing carbon and nitrogen contents.

  17. Removal of chromium and toxic ions present in mine drainage by Ectodermis of Opuntia

    Energy Technology Data Exchange (ETDEWEB)

    Barrera, Hector [Universidad Autonoma del Estado de Mexico, Facultad de Quimica, Paseo Colon interseccion Paseo Tollocan S/N, C.P. 50120, Toluca, Estado de Mexico (Mexico); Urena-Nunez, Fernando [Instituto Nacional de Investigaciones Nucleares, A.P.18-1027, Col. Escandon, Delegacion Miguel Hidalgo, C.P. 11801, Mexico, D.F. (Mexico); Bilyeu, Bryan [University of North Texas, Department of Materials Science and Engineering, P.O. Box 305310, Denton, TX 76203-5310 (United States); Barrera-Diaz, Carlos [Universidad Autonoma del Estado de Mexico, Facultad de Quimica, Paseo Colon interseccion Paseo Tollocan S/N, C.P. 50120, Toluca, Estado de Mexico (Mexico)]. E-mail: cbarrera@uaemex.mx

    2006-08-25

    This work presents conditions for hexavalent and trivalent chromium removal from aqueous solutions using natural, protonated and thermally treated Ectodermis of Opuntia. A removal of 77% of Cr(VI) and 99% of Cr(III) can be achieved. The sorbent material is characterized using scanning electron microscopy, energy dispersive X-ray spectroscopy, infrared spectroscopy, thermogravimetric analysis, before and after the contact with the chromium containing aqueous media. The results obtained from the characterization techniques indicate that the metal ion remains on the surface of the sorbent material. The percentage removal is found to depend on the initial chromium concentration and pH. The Cr(VI) and Cr(III) uptake process is maximum at pH 4, using 0.1 g of sorbent per liter of aqueous solution. The natural Ectodermis of Opuntia showed a chromium adsorption capacity that was adequately described by the Langmuir adsorption isotherm. Finally, an actual mine drainage sample that contained Cd, Cr, Cu, Fe Zn, Ni and Pb was tested under optimal conditions for chromium removal and Ectodermis of Opuntia was found to be a suitable sorbent material. The use of this waste material for the treatment of metal-containing aqueous solutions as well as mine drainage is effective and economical.

  18. Anaerobic bio-removal of uranium (VI) and chromium (VI): Comparison of microbial community structure

    Energy Technology Data Exchange (ETDEWEB)

    Martins, Monica [Centro de Ciencias do Mar, Universidade do Algarve, Campus de Gambelas, 8005-139 Faro (Portugal); Faleiro, Maria Leonor [IBB - Centro de Biomedicina Molecular e Estrutural, Universidade do Algarve, Campus de Gambelas, 8005-139 Faro (Portugal); Chaves, Sandra; Tenreiro, Rogerio [Universidade de Lisboa, Faculdade de Ciencias, Centro de Biodiversidade, Genomica Integrativa e Funcional (BioFIG), Campus de FCUL, Campo Grande 1749-016 Lisboa (Portugal); Santos, Erika [Centro de Ciencias do Mar, Universidade do Algarve, Campus de Gambelas, 8005-139 Faro (Portugal); Costa, Maria Clara, E-mail: mcorada@ualg.pt [Centro de Ciencias do Mar, Universidade do Algarve, Campus de Gambelas, 8005-139 Faro (Portugal)

    2010-04-15

    Several microbial communities, obtained from uranium contaminated and non-contaminated samples, were investigated for their ability to remove uranium (VI) and the cultures capable for this removal were further assessed on their efficiency for chromium (VI) removal. The highest efficiency for removal of both metals was observed on a consortium from a non-contaminated soil collected in Monchique thermal place, which was capable to remove 91% of 22 mg L{sup -1} U(VI) and 99% of 13 mg L{sup -1} Cr(VI). This study revealed that uranium (VI) removing communities have also ability to remove chromium (VI), but when uranium (VI) was replaced by chromium (VI) several differences in the structure of all bacterial communities were observed. TGGE and phylogenetic analysis of 16S rRNA gene showed that the uranium (VI) removing bacterial consortia are mainly composed by members of Rhodocyclaceae family and Clostridium genus. On the other hand, bacteria from Enterobacteriaceae family were detected in the community with ability for chromium (VI) removal. The existence of members of Enterobacteriaceae and Rhodocyclaceae families never reported as chromium or uranium removing bacteria, respectively, is also a relevant finding, encouraging the exploitation of microorganisms with new abilities that can be useful for bioremediation.

  19. Synchrotron-based analysis of chromium distributions in multicrystalline silicon for solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Jensen, Mallory Ann; Hofstetter, Jasmin; Morishige, Ashley E.; Coletti, Gianluca; Lai, Barry; Fenning, David P.; Buonassisi, Tonio

    2015-05-18

    Chromium (Cr) can degrade silicon wafer-based solar cell efficiencies at concentrations as low as 10(10) cm(-3). In this contribution, we employ synchrotron-based X-ray fluorescence microscopy to study chromium distributions in multicrystalline silicon in as-grown material and after phosphorous diffusion. We complement quantified precipitate size and spatial distribution with interstitial Cr concentration and minority carrier lifetime measurements to provide insight into chromium gettering kinetics and offer suggestions for minimizing the device impacts of chromium. We observe that Cr-rich precipitates in as-grown material are generally smaller than iron-rich precipitates and that Cri point defects account for only one-half of the total Cr in the as-grown material. This observation is consistent with previous hypotheses that Cr transport and CrSi2 growth are more strongly diffusion-limited during ingot cooling. We apply two phosphorous diffusion gettering profiles that both increase minority carrier lifetime by two orders of magnitude and reduce [Cr-i] by three orders of magnitude to approximate to 10(10) cm(-3). Some Cr-rich precipitates persist after both processes, and locally high [Cri] after the high-temperature process indicates that further optimization of the chromium gettering profile is possible. (C) 2015 AIP Publishing LLC.

  20. Compliance of a cobalt chromium coronary stent alloy – the COVIS trial

    Directory of Open Access Journals (Sweden)

    Schwinger Robert HG

    2005-10-01

    Full Text Available Abstract Background Cobalt chromium coronary stents are increasingly being used in percutaneous coronary interventions. There are, however, no reliable data about the characteristics of unfolding and visibility of this stent alloy in vivo. The aim of this study is to compare cobalt chromium coronary stents with conventional stainless steel stents using intracoronary ultrasound. Methods Twenty de novo native coronary stenoses ≤ 20 mm in length (target vessel reference diameter ≥ 2.5 and ≤ 4.0 mm received under sequential intracoronary ultrasound either a cobalt chromium stent (Multi-Link Vision®; n = 10 or a stainless steel stent (Multi-Link Zeta®; n = 10. Results For optimal unfolding, the cobalt chromium stent requires a higher balloon deployment pressure (13.90 ± 2.03 atm than the stainless steel stent (11.50 ± 2.12 atm. Furthermore, the achieved target vessel diameter of the cobalt chromium stent (Visibility-Index QCA/IVUS Multi-Link Vision®1.13 / Multi-Link Zeta® 1.04 is more easily overrated by Quantitative Coronary Analysis. Conclusion These data indicate that stent material-specific recommendations for optimal implantation pressure and different stent material with an equal design should both be considered in interpreting QCA-analysis.