WorldWideScience

Sample records for chromium 54 reactions

  1. Surface Reactions Limiting Chromium(VI) Generation from Naturally Derived Chromium(III) Minerals

    Science.gov (United States)

    Hausladen, D.; Fendorf, S. E.

    2015-12-01

    Chromium(III)-bearing minerals, commonly found in serpentinite and ultramaphic rocks, are ubiquitous in California soils and along convergent plate boundaries worldwide. Elevated concentrations of carcinogenic Cr(VI) have been measured in groundwater throughout the state, even in aquifers untouched by anthropogenic contamination. In most natural systems, manganese oxides are the only known, kinetically viable, oxidant of Cr(III). Numerous laboratory studies have demonstrated a finite capacity of Mn-oxides to generate Cr(VI) before surface alterations inhibit further Cr-oxidation. The extent to which these processes dictate the inhibition, and subsequent regeneration, of Mn-oxidation capacity within structured soils and sediments is not well understood. Here we use artificial soil aggregates made of Fe(III),Cr(III)-hydroxide-coated quartz sand and surrounded by aerated solute flow (pH 8, 30mM HEPES, 10mM HCO3-) to investigate C(VI) generation within ultramafic rock derived sediment and processes inhibiting manganese reactivity. We found that while Cr(VI)-production scaled with Cr-mineral solubility; Cr(VI) effluent concentrations from aggregates of both lower and higher solubility Cr(III)-minerals peaked very soon after reaction with birnessite (within 2 days and 4 days, respectively). Once Cr(VI) production plateaued (t=22 days) aggregate influent was acidified (pH 5, 30mM C2H3O2-). Despite increasing Cr(III) solubility at lower pH, aqueous Cr(VI) production further decreased. A secondary pulse of Cr(VI) generation was seen only after the surrounding solute returned to initial conditions (pH 8). As with the initial pulse, Cr(VI) concentration scaled with mineral solubility. Collectively, our results demonstrate the extent that natural fluctuations in groundwater composition, both as a result of irrigation or precipitation events, have the potential to both regenerate and inhibit Mn-oxide surfaces. These synthetic soil aggregates provide insight into how fluctuating

  2. Reaction Process of Chromium Slag Reduced by Industrial Waste in Solid Phase

    Institute of Scientific and Technical Information of China (English)

    SHI Yu-min; DU Xing-hong; MENG Qing-jia; SONG Shi-wei; SUI Zhi-tong

    2007-01-01

    M, a particular industrial waste, was selected to detoxify chromium slag at a high temperature. The carbon remaining in M reduced Cr (Ⅵ) of Na2CrO4 borne in the chromium slag to Cr (Ⅲ) in the solid phase reaction, and its thermodynamics and kinetics were studied. The reduction process of Na2CrO4 by carbon produced CO, which was endothermic. Under the experimental condition, the apparent activation energy was 4.41 kJ·mol-1, the apparent order of reaction for Na2CrO4 was equal to one, and the partial pressure of CO was only 0.22 Pa at 1 330 ℃.

  3. Redox reactions involving chromium, plutonium, and manganese in soils

    International Nuclear Information System (INIS)

    As a result of atmospheric testing of nuclear devices at the Nevada Test Site in southern Nevada, the soil and vegetation of several areas on the test site are contaminated with transuranic elements, particularly Pu and Am. A program is being developed to monitor the dispersion and bioavailability of transuranics, especially plutonium, in the environment. Cr reactions in soil were investigated as a possible general model for Pu reactions in soil, since it was postulated that the redox chemistries of the two elements should be similar. Chemical fractionation methods were used to determine the redox states of Pu in a Nevada Test Site soil and the amounts of Pu associated with various soil components in order to deduce possible reactions between the various Pu species and soil components so that weathering and dispersion by chemical mechanisms can be predicted. Chemical fractionation and kinetics experiments were performed to study reactions of Cr with soil, manganese oxides, and fulvic acids in order to provide information to eventually develop a qualitative, predictive model for Pu behavior in soil. The fractionation of soil Pu revealed that only a few percent of the total soil Pu was associated with organic matter and/or iron oxides with the remainder probably existing as stable PuO2. Oxidized Pu was found in the soil, but the presence of oxidized Pu appeared to be due to Pu dissolved by the extracting solutions reacting with the soil manganese oxides. The amount of oxidized Pu found was a very small fraction of the total soil Pu, although carbonate-rich waters dissolving PuO2 in the presence of manganese oxides could result in oxidized Pu leaching through the soil profile

  4. Measurements of the Fe-54 (n,p) Mn-54 Reaction Cross Section in the Neutron Energy Range 2.3-3.8 MeV

    International Nuclear Information System (INIS)

    We have measured the 54Fe (n, p) 54Mn reaction cross section using a surface barrier detector to record the number of protons released in the reaction. The neutron flux was determined by means of a hydrogenous radiator, detecting the scattered protons with the solid state detector, and calculating the number of impinging neutrons from the well known n-p scattering cross section. The 54Fe (n, p) 54Mn reaction cross section is found to increase from 25 mb at 2.3 MeV to 208 mb at 3.5 MeV

  5. The behaviour of cesium 137, chromium 51, cobalt 60, Manganese 54, sodium 22 and zinc 65 in simulated estuarine environments. Effects of suspended mineral particles and dissolved organic matters

    International Nuclear Information System (INIS)

    This laboratory investigation studied the retention of 6 radionuclides (cesium 137, chrome 51, cobalt 60, manganese 54, sodium 22 and zinc 65) on three types of clay particles (kaolinite, illite, montmorillonite) and on sediments, suspended in media with salinities ranging between 0 and 34 per mill, with or without organic matters. Measurement of the radioactivity retained by the particles after 5 days' contact with the radionuclide made it possible to calculate the percentages retained and the distribution coefficients, and to follow their evolution versus salinity. Parallel experiments studied the behaviours of the 6 radionuclides as a function of experimental factors (wall effect, contact time..). An exhaustive bibliographic review gives the state-of-the-art of the knowledge. The following conclusions were derived: - the retention of all the radionuclides but chromium 51 decreased as soon as a low salinity appeared. Chromium (available as Cr3+) precipitated quickly and strongly during fixation whatever the surfaces or the conditions: - as for the role of the clay type, illite showed a strong affinity for cesium 137; manganese 54 had a particular behaviour with montmorillonite that enhanced its precipitation into MnO2; with cobalt, sodium and zinc, the percentages retained were always <= 20% and the type of clay had little effect; - dissolved organic matters had little effect on the behaviour of cesium or chromium; for sodium and zinc, strong complexation occured with the organic matter which was retained on the particles; cobalt and manganese gave intermediate results; - attempts to modeling emphasized the specific feature of the various reactions (adsorption by exchange with some compensating cations, absorption in the crystal lattice, surface retention of particular compounds)

  6. Level density and mechanism of deuteron-induced reactions on 54,58,56Fe

    Science.gov (United States)

    Ramirez, A. P. D.; Voinov, A. V.; Grimes, S. M.; Byun, Y.; Brune, C. R.; Massey, T. N.; Akhtar, S.; Dhakal, S.; Parker, C. E.

    2015-07-01

    Deuteron elastic cross sections, as well as neutron, proton, and α -particle emission spectra, from d + 54,58,56Fe reactions have been measured with deuteron beam energies of 5, 7, and 9 MeV. Optical model parameters have been tested against our experimental data. The fraction of total reaction cross section responsible for the formation of compound nuclei has been deduced from the angular distributions. The degree of discrepancy between calculated and experimental compound cross sections was found to increase with increasing neutron number. The nuclear level densities of the residual nuclei 57Co, 55Co, 57Fe, 55Fe, 52Mn, 54Mn have been deduced from the compound double differential cross sections. The Gilbert-Cameron model with Iljinov parameter systematics [A. S. Iljinov and M. V. Mebel, Nucl. Phys. A 543, 517 (1992)], 10.1016/0375-9474(92)90278-R was found to have a good agreement with our results.

  7. The role of interstitial nitrogen in the precipitation hardening reactions in high-chromium ferritic steels

    International Nuclear Information System (INIS)

    The effects of exposure to temperatures in the range 475 - 800 C on the hardness and associated microstructure of high chromium ferritic steels has been investigated. Low-carbon 26Cr-1Mo steels containing 0,02 - 0,04% nitrogen were found to constitute an age hardening system when quenched from a temperature of nitrogen solubility and exposed at temperatures in the range 600 - 700 C. TEM observations on thin foils revealed that hardening was associated with the formation of a high density of Cr-N zones. Ageing at 475 C and 550 C produced hardening due to the formation of chromium-rich ferrite phases α' as result of the miscibility gap in the Fe-Cr phase diagram. However the presence of interstitial nitrogen in solution in the steel considerably reduced the rate of hardening, especially at 475 C. This type of decomposition occurs by a mechanism of nucleation and growth, forming zones similar to those formed during an ageing at 600 C. When depleted of interstitial nitrogen, the specimens aged at 475 C underwent spinodal decomposition. Thus nitrogen in solid solution was found to have a significant effect on the 475 C hardening reaction. Precision X-ray diffraction measurements revealed the presence of secondary diffraction peaks associated with the Bragg peaks, which confirmed the formation of Cr-rich phases during ageing at 475 C. The calculated associated lattice parameter measurements allowed estimates of the compositions of the decomposition phases to be made. These were calculated to be about 6-18% Cr in the Fe-rich and 60-80% Cr in the Cr-rich phases of the 26Cr-1Mo steel

  8. Reactions of the excited state of polypyridyl chromium(III) ion

    Energy Technology Data Exchange (ETDEWEB)

    Steffan, C.

    1990-09-21

    There has been much recent interest in the photochemistry and photophysics of transition metal polypyridine complexes due to the possibility of their use in solar energy conversion systems. The excited state of these compounds are known to undergo useful electron transfer and energy transfer reactions. This work attempts to elucidate the mechanism of the quenching of *CrL{sub 3}{sup 3+} (where L = 2,2{prime}-bipyridine, 4,4{prime}-dimethyl-2,2{prime}-bipyridine, 1,10-phenanthroline, 5-chloro-1,10-phenanthroline, 5-methyl-1,10-phenanthroline) by oxalate ions in neutral pH. Evidence suggests an ion-pairing pre-equilibrium followed by rate limiting electron transfer to produce CrL{sub 3}{sup 2+} and CO{sub 2}{sup {minus}} can then react with ground state chromium(III) species to produce another mole of the reduced product or it can produce a secondary transient as in the case of phenanthroline and substituted phenanthroline complexes. The secondary transient reacts to produce CrL{sub 3}{sup 2+} in a subsequent reaction. 85 refs., 24 figs., 7 tabs.

  9. Thermal and Photochemical Reactions of NO2 on a Chromium (III) Oxide Surface

    Science.gov (United States)

    Nishino, N.; Finlayson-Pitts, B. J.

    2011-12-01

    Chromium oxide (Cr2O3) is a major component of the oxide layer on stainless steel surfaces. It is also widely used as pigment in paints and roofs and as a protective coating on various surfaces. While many studies have focused on the catalytic activity of Cr2O3 surfaces for selective catalytic reduction (SCR), less attention has been paid to its surface chemistry involving atmospherically important species such as NO2 under atmospheric conditions. In this study, we have investigated thermal and photochemical reactions of NO2 in the presence and the absence of water vapor, using a thin layer of Cr2O3 as a model for the surface of stainless steel as well as other similarly coated surfaces in the boundary layer. A 30 nm thick Cr2O3 film was deposited on a germanium attenuated total reflectance (ATR) crystal, and the changes in the surface species were monitored by Fourier Transform Infrared (FTIR) spectroscopy. Upon NO2 adsorption, nitrate (NO3-) ions appeared likely coordinated to Cr3+ ion(s). The NO3- peaks reversibly shifted when water vapor was added, suggesting that NO3- become solvated. Irradiation at 311 nm led to a decrease in NO3- ions under both dry and humid conditions. The major gas-phase species formed by the irradiation was NO under dry conditions, while NO2 was mainly formed in the presence of H2O. Possible mechanisms and the implications for heterogeneous NO2 chemistry in the boundary layer will be discussed. The results will also be compared to similar chemistry on other surfaces.

  10. Novel Substitution Reactions of 5-(4-Nitrophenyl)-10,15,20-triphenyl porphyrin with Nucleophilic Reagents

    Institute of Scientific and Technical Information of China (English)

    SHAO,Zhi-Jun; CHEN,Zhang-Ping; OUYANG,Yan; ZENG,Dan-Li

    2004-01-01

    @@ Substitution reactions of 5-(4-nitrophenyl)-10,15,20-triphenylporphyrin (1)and its Ni(Ⅱ) complexe 2 with different nucleophilic reagents were studied for preparing asymmetric porphyrin. The reaction products are different with the nucleophilic reagents changing. Diporphyrin (3) was obtained when compound 1 reacted with sodium phenoxide or diphenoxide ion in DMF solution. Whereas the nitro group was reduced and 5-(4-amino-phenyl)-10,15,20-triphenylporphyrinato Nickel(Ⅱ) (4) was achieved when compound 2 reacted with above nuleophilic reagents in the same condition. The reductive product 5-(4-aminophenyl)-10,15,20-triphenylporphyrin (5) was also achieved when 1 reacted with mercaptoethanol or thiophene and lithium hydroxide. While the nitro group was substituted by cyanide anion and 5-(4-nitrilephenyl)-10,15,20-triphenylporphyrin (6) was achieved when 1 reacted with sodium cyanide.

  11. Laser Double Ablation Reactions of Chromium(Iron) and Sulfur Clusters

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    @@ Introduction The sulfides of transitional metals chromium[1-3] and iron[4] are of great importance in material and biology sciences due to their characteristic structures and properties. So the study on the properties of Cr-S and Fe-S clusters will give many contributions to the understanding of physical and chemical behavior of those compounds.

  12. Calculation of excitation functions of the 54,56,57,58Fe(, ) reaction from threshold to 30 MeV

    Indian Academy of Sciences (India)

    Damewan Suchiang; J Joseph Jeremiah; B M Jyrwa

    2014-10-01

    The cross-sections for the formation of 54,56,57,58Co in the 54,56,57,58Fe(, ) reaction from threshold to 30 MeV protons have been theoretically calculated using the TALYS-1.4 nuclear model code, whereby we have studied major nuclear reaction mechanisms, including direct, preequilibrium and compound nuclear reaction. Subsequently, the level density and shell damping parameters have been adjusted and at the same time, the odd–even effects are well comprehended. The excitation functions have been compared with experimental nuclear data. It is observed that the theoretical cross-sections match fairly well. Proton-induced reaction cross-sections provide clues to understand the nuclear structure and offers a good testing ground for ideas about nuclear forces. In addition, complete information in this field is very much required for application in accelerator-driven subcritical system.

  13. Environmental Factors Affecting Chromium-Manganese Oxidation-Reduction Reactions in Soil

    Institute of Scientific and Technical Information of China (English)

    D.O.P.TREBIEN; L.BORTOLON; M.J.TEDESCO; C.A.BISSANI; F.A.O.CAMARGO

    2011-01-01

    Disposal of chromium (Cr) hexavalent form, Cr(Ⅵ), in soils as additions in organic fertilizers, liming materials or plant nutrient sources can be dangerous since Cr(Ⅵ) can be highly toxic to plants, animals, and humans. In order to explore soil conditions that lead to Cr(Ⅵ) generation, this study were performed using a Paleudult (Dystic Nitosol) from a region that has a high concentration of tannery operations in the Rio Grande do Sul State, southern Brazil. Three laboratory incubation experiments were carried out to examine the influences of soil moisture content and concentration of cobalt and organic matter additions on soil Cr(Ⅵ) formation and release and manganese (Mn) oxide reduction with a salt of chromium chloride (CrCl3) and tannery sludge as inorganic and organic sources of Cr(Ⅲ), respectively. The amount of Cr(Ⅲ) oxidation depended on the concentration of easily reducible Mn oxides and the oxidation was more intense at the soil water contents in which Mn(Ⅲ/Ⅳ) oxides were more stable. Soluble organic compounds in soil decreased Cr(Ⅵ) formation due to Cr(Ⅲ) complexation. This mechanism also resulted in the decrease in the oxidation of Cr(Ⅲ) due to the tannery sludge additions. Chromium(Ⅲ) oxidation to Cr(Ⅵ) at the solid/solution interface involved the following mechanisms:the formation of a precursor complex on manganese (Mn) oxide surfaces, followed by electron transfer from Cr(Ⅲ) to Mn(Ⅲ or Ⅳ),the formation of a successor complex with Mn(Ⅱ) and Cr(Ⅵ), and the breakdown of the successor complex and release of Mn(Ⅱ) and Cr(Ⅵ) into the soil solution.

  14. Projectile influence on production cross section for ^48Ca-, ^50Ti-, and ^54Cr- induced fusion-evaporation reactions

    Science.gov (United States)

    Mayorov, D. A.; Werke, T. A.; Alfonso, M. C.; Bennett, M. E.; Folden, C. M., III

    2013-04-01

    Evaporation residue excitation functions for ^48Ca, ^50Ti + ^159Tb and ^48Ca, ^54Cr + ^162 Dy were measured at Texas A&M University using the vacuum spectrometer MARS. The produced residues are weakly deformed nuclei near the N = 126 shell closure. However, the production cross sections are insensitive to the associated shell stabilization to the fission barrier, an observation previously reported in literature. The ratio of maximum production cross sections between the ^48Ca/^50Ti and ^48Ca/^54Cr reactions is 47 and 7100, respectively. These substantial differences can be reproduced in theoretical calculations by inclusion of collective enhancements during de-excitation of the compound nucleus. The competition between quasifission and complete fusion further contributes to the observed separation in the excitation functions. Model-dependent estimates of the compound nucleus formation probability, PCN, yield ratios of PCN(^48Ca + ^159 Tb) / PCN(^50Ti + ^159 Tb) 2.5 and PCN(^48Ca + ^162Dy) / PCN(^54Cr + ^162Dy) 5. Heavy-ion fusion reactions with ^48Ca, ^50Ti, and ^54Cr projectiles are of interest due to modern-day efforts to synthesize superheavy elements 119 and 120 in warm fusion reactions with projectiles having Z 20.

  15. Speciation, Dissolution, and Redox Reactions of Chromium Relevant to Pretreatment and Separation of High-Level Tank Wastes

    International Nuclear Information System (INIS)

    Chromium, one of the problematic elements in tank sludges, is considered the most important constituent in defining the total volume of high-level radioactive waste (HLW) glass. Current sludge washing processes (e.g. caustic leaching, 3 M NaOH) are not effective in removing Cr. This inefficient removal would result in production of an unacceptably large volume of HLW glass and thus a tremendous increase in the cost of waste disposal. This proposed research seeks to develop fundamental data for chromium (Cr) reactions that are not currently available but are essential for developing effective methodologies for removing Cr form high-level waste (HLW). Our objectives are to study (1) the dissolution of several solid phases (e.g., CrOOH, Cr2O3(c), Cr(OH)3, and Fe and Cr, binary hydroxides, identified to be important from sludge leaching studies) in highly alkaline solutions and in the presence of other electrolytes (e.g., carbonate, phosphate, sulfate, nitrite), and (2) the effect of the nature of Cr solid phases and aqueous species on their redox reactivity with a variety of potential oxidants (e.g., H2o2, persulfate, O2, and ferrate). This information will provide critical support for developing enhanced pretreatment strategies for removing Cr from HLW and will achieve a major cost reduction HLW disposal

  16. Kinetics and Mechanism of the Reaction between Chromium(III and 2,3-Dihydroxybenzoic Acid in Weak Acidic Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Athinoula L. Petrou

    2010-01-01

    Full Text Available The reaction between chromium(III and 2,3-dihydroxybenzoic acid (2,3-DHBA takes place in at least three stages, involving various intermediates. The ligand (2,3-DHBA-to-chromium(III ratio in the final product of the reaction is 1 : 1. The first stage is suggested to be the reaction of [Cr(H2O5(OH]2+ with the ligand in weak acidic aqueous solutions that follows an Id mechanism. The second and third stages do not depend on the concentrations of chromium(III, and their activation parameters are ΔH≠=61.2±3.1 kJmol−1, ΔS≠=−91.1±11.0 JK−1mol−1, ΔH≠=124.5±8.7 kJmol−1, and ΔS≠=95.1±29.0 JK−1mol−1. These two stages are proposed to proceed via associative mechanisms. The positive value of ΔS≠ can be explained by the opening of a four-membered ring (positive entropy change and the breaking of a hydrogen bond (positive entropy change at the associative step of the replacement of the carboxyl group by the hydroxyl group at the chromium(III center (negative entropy change in associative mechanisms. The reactions are accompanied by proton release, as shown by the pH decrease.

  17. Search for proton emission in {sup 54}Ni and multi-nucleon transfer reactions in the actinide region

    Energy Technology Data Exchange (ETDEWEB)

    Geibel, Kerstin

    2012-06-15

    The first part of the thesis presents the investigation of fusion-evaporation reactions in order to verify one-proton emission from the isomeric 10{sup +} state in the proton rich nucleus {sup 54}Ni. Between the years 2006 and 2009 a series of experimental studies were performed at the Tandem accelerator in the Institut fuer Kernphysik (IKP), University of Cologne. These experiments used fusion-evaporation reactions to populate {sup 54}Ni via the two-neutron-evaporation channel of the compound nucleus {sup 56}Ni. The cross section for the population of the ground state of {sup 54}Ni was predicted to be in orders of microbarn. This required special care with respect to the sensitivity of the experimental setup, which consisted of a double-sided silicon-strip detector (DSSSD), a neutron-detector array and HPGe detectors. In two experiments the excitation functions of the reactions ({sup 32}S+{sup 24}Mg) and ({sup 28}Si+{sup 28}Si) were determined to find the optimal experimental conditions for the population of {sup 54}Ni. A final experiment employed a {sup 28}Si beam at an energy of 70 MeV, impinging on a {sup 28}Si target. With a complex analysis it is possible to obtain a background-free energy spectrum of the DSSSD. An upper cross section limit for the population of the 10{sup +} state in {sup 54}Ni is established at σ({sup 54}Ni(10{sup +})) ≤ (13.9 ± 7.8) nbarn. In the second part of the thesis the population of actinide nuclei by multi-nucleon transfer reactions is investigated. Two experiments, performed in 2007 and 2008 at the CLARA-PRISMA setup at the Laboratori Nazionali di Legnaro, are analyzed with respect to the target-like reaction products. In both experiments {sup 238}U was used as target. A {sup 70}Zn beam with 460 MeV and a {sup 136}Xe beam with 926 MeV, respectively, impinged on the target, inducing transfer reactions. Kinematic correlations between the reaction partners are used to obtain information on the unobserved target-like reaction

  18. On texture formation of chromium electrodeposits

    DEFF Research Database (Denmark)

    Nielsen, Christian Bergenstof; Leisner, Peter; Horsewell, Andy

    1998-01-01

    The microstructure, texture and hardness of electrodeposited hard, direct current (DC) chromium and pulsed reversed chromium has been investigated. These investigations suggest that the growth and texture of hard chromium is controlled by inhibition processes and reactions. Further, it has been e...... established that codeposition of Cr2O3 nanoparticles is a general feature of DC chromium electrodeposition....

  19. Substoichiometric extraction of chromium

    International Nuclear Information System (INIS)

    Substoichiometric extraction of chromium with tetraphenylarsonium chloride (TPACl), tri-n-octylamine (TNOA), diethylammonium diethyldithiocarbamate (DDDC) and ammonium pyrrolidinedithiocarbamate (APDC) was examined in detail. Chromium can be extracted substoichiometrically in a pH range, which is 1.1-2.6 for the TPACl compound, 0.6-2.3 for the TNOA compound, 5.1-6.4 for the DDDC chelate and 3.9-4.9 for the APDC chelate. Chromium in high-purity calcium carbonate, Orchard Leaves (NBS SRM-1571) and Brewers Yeast (NBS SRM-1569) was determined by neutron activation analysis combined with substoichiometric extraction by DDDC and APDC. The values of 2.0+-0.02 ppm and 2.6+-0.2 ppm were obtained for Brewers Yeast and Orchard Leaves, respectively. These values were in good agreement with those reported by NBS. The reaction mechanism and the reaction ratio between hexavalent chromium and dithiocarbamate are also discussed. (author)

  20. Mechanistic aspects of the copolymerization reaction of carbon dioxide and epoxides, using a chiral salen chromium chloride catalyst.

    Science.gov (United States)

    Darensbourg, Donald J; Yarbrough, Jason C

    2002-06-01

    The air-stable, chiral (salen)Cr(III)Cl complex (3), where H(2)salen = N,N'-bis(3,5-di-tert-butyl-salicylidene)-1,2-cyclohexene diamine, has been shown to be an effective catalyst for the coupling of cyclohexene oxide and carbon dioxide to afford poly(cyclohexenylene carbonate), along with a small quantity of its trans-cyclic carbonate. The thus produced polycarbonate contained >99% carbonate linkages and had a M(n) value of 8900 g/mol with a polydispersity index of 1.2 as determined by gel permeation chromatography. The turnover number (TON) and turnover frequency (TOF) values of 683 g of polym/g of Cr and 28.5 g of polym/g of Cr/h, respectively for reactions carried out at 80 degrees C and 58.5 bar pressure increased by over 3-fold upon addition of 5 equiv of the Lewis base cocatalyst, N-methyl imidazole. Although this chiral catalyst is well documented for the asymmetric ring-opening (ARO) of epoxides, in this instance the copolymer produced was completely atactic as illustrated by (13)C NMR spectroscopy. Whereas the mechanism for the (salen)Cr(III)-catalyzed ARO of epoxides displays a squared dependence on [catalyst], which presumably is true for the initiation step of the copolymerization reaction, the rate of carbonate chain growth leading to copolymer or cyclic carbonate formation is linearly dependent on [catalyst]. This was demonstrated herein by way of in situ measurements at 80 degrees C and 58.5 bar pressure. Hence, an alternative mechanism for copolymer production is operative, which is suggested to involve a concerted attack of epoxide at the axial site of the chromium(III) complex where the growing polymer chain for epoxide ring-opening resides. Preliminary investigations of this (salen)Cr(III)-catalyzed system for the coupling of propylene oxide and carbon dioxide reveal that although cyclic carbonate is the main product provided at elevated temperatures, at ambient temperature polycarbonate formation is dominant. A common reaction pathway for

  1. Chromium complexes of an isomeric N-donor ligand, 2-[(N-arylamino)phenylazo]pyridine: amination reactions, X-ray structure, and redox properties.

    Science.gov (United States)

    Kamar, Kunal K; Saha, Amrita; Castiñeiras, Alfonso; Hung, Chen-Hsiung; Goswami, Sreebrata

    2002-08-26

    The chromium chemistry of two positional isomers of the ligand 2-[(N-arylamino)phenylazo]pyridine (HL(1)and HL(2)) are described. While the ligand HL(1) coordinates as a bischelating tridentate N,N,N-donor, [L(1)](-), with deprotonation of the amine nitrogen, its isomer HL(2) coordinates as a neutral bidentate N,N-donor. The amine nitrogen in this case remains protonated. Thus the reaction of CrCl(3).nH(2)O with HL(1) produced the brown cationic complex, [Cr(L(1))(2)](+), [1](+). The representative X-ray structure of [1a](ClO(4)) is reported. The two azo nitrogens of the anioinc tridentate ligand approach the metal center closest with Cr(1)-N(azo) av 1.862(6) A. There is a significant degree of ligand backbone conjugation in the coordinated ligands, which resulted in shortening of the C-N distances and also in lengthening of the diazo (N=N) distances. Two synthetic approaches for the synthesis of chromium complexes of HL(2) are investigated. The first approach is based on the substitution reaction, wherein all the coordinated CO ligands of Cr(CO)(6) were completely substituted by the three bidentate HL(2) ligands to produce a violet complex [Cr(HL(2))(3)]. The second approach is based on para-amination reaction of coordinated 2-(phenylazo)pyridine (pap). Thus the reaction of an inert complex, [CrCl(2)(pap)(2)], with ArNH(2) yields a mixed ligand complex, [CrCl(2)(pap)(HL(2))], 3. In this reaction one of the two coordinated pap ligands in [CrCl(2)(pap)(2)] undergoes amination at the para carbon (with respect to the diazo function) to yield HL(2) in situ. This metal-promoted transformation is authenticated by the X-ray structure determination of a representative complex, [CrCl(2)(pap)(HL(2a))], 3a. Notable differences in bond distances along the ligand backbones of the two coordinated ligands in 3a indicate different levels of metal-ligand overlap in this complex. All the chromium complexes of HL(2) are characterized by their intense blue-violet color. The

  2. Nuclear tracks in PADC induced by neutron, heavy ion and energetic fragments formed in the reaction {sup 54}Cr + {sup 208}Pb, at 320 MeV

    Energy Technology Data Exchange (ETDEWEB)

    Barbui, M. [INFN Laboratori Nazionali di Legnaro, I-35020 Legnaro (Pd) (Italy); Fabris, D.; Moretto, S.; Nebbia, G. [Dipartimento di Fisica and Sezione INFN Padova, I-35131 Padova (Italy); Nemeth, P. [Departamento de Fisica, Universidad Simon Bolivar, Caracas 1080A (Venezuela, Bolivarian Republic of); Palfalvi, J. [Atomic Energy Research Institute P.O. Box 49, H-1525 Budapest (Hungary); Pesente, S. [Dipartimento di Fisica and Sezione INFN Padova, I-35131 Padova (Italy); Prete, G. [INFN Laboratori Nazionali di Legnaro, I-35020 Legnaro (Pd) (Italy); Sajo-Bohus, L., E-mail: sajobhus@gmail.co [Departamento de Fisica, Universidad Simon Bolivar, Caracas 1080A (Venezuela, Bolivarian Republic of); Viesti, G. [Dipartimento di Fisica and Sezione INFN Padova, I-35131 Padova (Italy)

    2009-10-15

    Passive nuclear track detectors in the study of multi fragmentation and compound nucleus fission in the fusion reaction {sup 54}Cr + {sup 208}Pb, leading to composite systems with Z = 106 is given. Results indicate that mostly nuclear tracks are related to fragments with low atomic number and less than 11% to beam like particles in opposition to the expected distribution.

  3. Nuclear tracks in PADC induced by neutron, heavy ion and energetic fragments formed in the reaction 54Cr + 208Pb, at 320 MeV

    International Nuclear Information System (INIS)

    Passive nuclear track detectors in the study of multi fragmentation and compound nucleus fission in the fusion reaction 54Cr + 208Pb, leading to composite systems with Z = 106 is given. Results indicate that mostly nuclear tracks are related to fragments with low atomic number and less than 11% to beam like particles in opposition to the expected distribution.

  4. Chromium in aqueous nitrate plutonium process streams: Corrosion of 316 stainless steel and chromium speciation

    International Nuclear Information System (INIS)

    This study was undertaken to determine if chromium(+6) could exist in plutonium process solutions under normal operating conditions. Four individual reactions were studied: the rate of dissolution of stainless steel, which is the principal source of chromium in process solutions; the rate of oxidation of chromium(+3) to chromium(+6) by nitric acid; and the reduction of chromium(+6) back to chromium(+3) by reaction with stainless steel and with oxalic acid. The stainless steel corrosion rate was found to increase with increasing nitric acid concentration, increasing hydrofluoric acid concentration, and increasing temperature. Oxidation of chromium(+3) to chromium(+6) was negligible at room temperature and only became significant in hot concentrated nitric acid. The rate of reduction of chromium(+6) back to chromium(+3) by reaction with stainless steel or oxalic acid was found to be much greater than the rate of the reverse oxidation reaction. Based on these findings and taking into account normal operating conditions, it was determined that although there would be considerable chromium in plutonium process streams it would rarely be found in the (+6) oxidation state and would not exist in the (+6) state in the final process waste solutions

  5. Chromium Reaction Mechanisms for Speciation using Synchrotron in-Situ High-Temperature X-ray Diffraction.

    Science.gov (United States)

    Low, Fiona; Kimpton, Justin; Wilson, Siobhan A; Zhang, Lian

    2015-07-01

    We use in situ high-temperature X-ray diffraction (HT-XRD), ex-situ XRD and synchrotron X-ray absorption near edge structure spectroscopy (XANES) to derive fundamental insights into mechanisms of chromium oxidation during combustion of solid fuels. To mimic the real combustion environment, mixtures of pure eskolaite (Cr(3+)2O3), lime (CaO) and/or kaolinite [Al2Si2O5(OH)4] have been annealed at 600-1200 °C in air versus 1% O2 diluted by N2. Our results confirm for the first time that (1) the optimum temperature for Cr(6+) formation is 800 °C for the coexistence of lime and eskolaite; (2) upon addition of kaolinite into oxide mixture, the temperature required to produce chromatite shifts to 1000 °C with a remarkable reduction in the fraction of Cr(6+). Beyond 1000 °C, transient phases are formed that bear Cr in intermediate valence states, which convert to different species other than Cr(6+) in the cooling stage; (3) of significance to Cr mobility from the waste products generated by combustion, chromatite formed at >1000 °C has a glassy disposition that prevents its water-based leaching; and (4) Increasing temperature facilitates the migration of eskolaite particles into bulk lime and enhances the extent to which Cr(3+) is oxidized, thereby completing the oxidation of Cr(3+) to Cr(6+) within 10 min. PMID:26055512

  6. Production of radon and thorium isotopes near N=126 shell closure in 48Ca and 54Cr induced fusion reactions on 162Dy

    Science.gov (United States)

    Mayorov, Dmitriy; Werke, Tyler; Alfonso, Marisa; Folden, Charles

    2012-03-01

    Production of spherical evaporation residues (EVRs) near N=126 shell in 48Ca and 54Cr induced reactions on a 162Dy target was investigated at the Texas A&M University Cyclotron Institute using the vacuum separator MARS. For the 54Cr+162Dy reaction, only upper limits for the 4n exit-channel cross section were measured; this can be attributed to a sizably increased fissility of the 216Th compound nucleus relative to 210Rn formed in the 48Ca bombardment. A factor of > 7300 separates the production cross sections of the 4n EVRs from each reaction. A semi-empirical estimate of the lower limit on the fusion probability, PCN, ratio between the two heavy ion projectiles is PCN(48Ca+162Dy)/PCN(54Cr+162Dy) > 1.2. Investigation of spherical nuclei produced by heavy ion fusion reactions is of current interest due to efforts to synthesize superheavy nuclei near Z=120, N=184 nucleon shells. EVRs produced near the N=126 shell closure have previously revealed surprisingly low survival probabilities despite stabilization from shell effects. Similarly, enhancement of the fission channel in the de-excitation cascade of 210Rn and 216Th is observed in this work and this result can be well modeled by the inclusion of collective effects into the statistical decay of excited nuclei calculations. These results suggest that cross sections for production of superheavy nuclei near predicted Z=120, N=184 closed shells may be small regardless of the anticipated strong shell effects.

  7. Hexavalent and trivalent chromium in leather: What should be done?

    Science.gov (United States)

    Moretto, Angelo

    2015-11-01

    Trivalent chromium compounds are used for leather tanning, and chromium may be released during use of leather goods. In certain instances, small amounts of hexavalent chromium can be formed and released. Both trivalent and hexavalent chromium can elicit allergic skin reaction in chromium sensitised subjects, the latter being significantly more potent. Induction of sensitisation only occurs after exposure to hexavalent chromium. A minority of subjects are sensitised to chromium, and in a fraction of these subjects allergic skin reaction have been described after wearing leather shoes or, less frequently, other leather goods. The evidence that in all these cases the reaction is related to hexavalent chromium is not always strong. The content of hexavalent chromium in leather is regulated in European Union, but rate of release rather than content is relevant for allergic skin reaction. The role of trivalent chromium appear much less relevant if at all. Modern tanning procedure do not pose significant risk due to either hexavalent or trivalent chromium. Dismissing bad quality and worn-off leather goods is relevant in reducing or eliminating the skin reaction. It should also be pointed out that shoe components or substances other than chromium in leather may cause allergic/irritative skin reactions.

  8. Hexavalent and trivalent chromium in leather: What should be done?

    Science.gov (United States)

    Moretto, Angelo

    2015-11-01

    Trivalent chromium compounds are used for leather tanning, and chromium may be released during use of leather goods. In certain instances, small amounts of hexavalent chromium can be formed and released. Both trivalent and hexavalent chromium can elicit allergic skin reaction in chromium sensitised subjects, the latter being significantly more potent. Induction of sensitisation only occurs after exposure to hexavalent chromium. A minority of subjects are sensitised to chromium, and in a fraction of these subjects allergic skin reaction have been described after wearing leather shoes or, less frequently, other leather goods. The evidence that in all these cases the reaction is related to hexavalent chromium is not always strong. The content of hexavalent chromium in leather is regulated in European Union, but rate of release rather than content is relevant for allergic skin reaction. The role of trivalent chromium appear much less relevant if at all. Modern tanning procedure do not pose significant risk due to either hexavalent or trivalent chromium. Dismissing bad quality and worn-off leather goods is relevant in reducing or eliminating the skin reaction. It should also be pointed out that shoe components or substances other than chromium in leather may cause allergic/irritative skin reactions. PMID:26361854

  9. Peat and coconut fiber as biofilters for chromium adsorption from contaminated wastewaters.

    Science.gov (United States)

    Henryk, Kołoczek; Jarosław, Chwastowski; Witold, Żukowski

    2016-01-01

    Batch adsorption experiments were performed for the removal of chromium (III) and chromium (VI) ions from aqueous solutions using Canadian peat and coconut fiber. The Langmuir model was used to describe the adsorption isotherm. The maximum adsorption for peat reached 18.75 mg/g for Cr(III) and 8.02 mg/g for Cr(VI), whereas the value for fiber was slightly higher and reached 19.21 mg/g for Cr(III) and 9.54 mg/g for Cr(VI). Both chromium forms could be easily eluted from the materials. The adsorption of chromium forms to organic matter could be explained in terms of formation of donor-acceptor chemical covalent bound with hydroxyl groups as ligands and chromium as the central atom in the formed complex. The chromate-reducing activities were monitored with the use of electron paramagnetic resonance spectroscopy. The results showed that both adsorption and reduction occurred simultaneously and the maximum adsorption capacity of hexavalent chromium being equal to 95% for fiber and 92% for peat was obtained at pH 1.5. The reduction of Cr(VI) in wastewaters began immediately and disappeared after 20 h. Both materials contained yeast and fungi species which can be responsible for reduction of chromium compounds, due to their enzymatic activity (Chwastowski and Koloczek (Acta Biochim Pol 60: 829-834, 2013)). The reduction of Cr(VI) is a two-phase process, the first phase being rapid and based on chemical reaction and the second phase having biological features. After the recovery step, both types of organic materials can be used again for chromium adsorption without any loss in the metal uptake. Both of the materials could be used as biofilters in the wastewater treatment plants.

  10. A Kinetic Model of Chromium in a Flame

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Chromium has been identified as a carcinogenic metal.Incineration is the useful method for disposal of toxic chromium hazard waste and a chromium kinetic model in a flame is very important to study chromium oxidation.Chromium chemical kinetics over a range of temperatures of a hydrogen/air flame is proposed.Nine chromium compounds and fifty-eight reversible chemical reactions were considered The forward reaction rates are calculated based on the molecular collision approach for unknown ones and Arrhenius's Law for known ones.The backward reaction rates were calculated according to forward reaction rates, the equilibrium constants and chemical thermodynamics.It is verified by several equilibrium cases and is tested by a hydrogen/air diffusion flame.The results show that the kinetic model could be used in cases in which the chromium kinetics play an important role in a flame

  11. Synthesis of Bioactive 2-(Arylaminothiazolo[5,4-f]-quinazolin-9-ones via the Hügershoff Reaction or Cu- Catalyzed Intramolecular C-S Bond Formation

    Directory of Open Access Journals (Sweden)

    Damien Hédou

    2016-06-01

    Full Text Available A library of thirty eight novel thiazolo[5,4-f]quinazolin-9(8H-one derivatives (series 8, 10, 14 and 17 was prepared via the Hügershoff reaction and a Cu catalyzed intramolecular C-S bond formation, helped by microwave-assisted technology when required. The efficient multistep synthesis of the key 6-amino-3-cyclopropylquinazolin-4(3H-one (3 has been reinvestigated and performed on a multigram scale from the starting 5-nitroanthranilic acid. The inhibitory potency of the final products was evaluated against five kinases involved in Alzheimer’s disease and showed that some molecules of the 17 series described in this paper are particularly promising for the development of novel multi-target inhibitors of kinases.

  12. Characteristics of chromium-allergic dermatitis patients prior to regulatory intervention for chromium in leather

    DEFF Research Database (Denmark)

    Bregnbak, David; Thyssen, Jacob P; Zachariae, Claus;

    2014-01-01

    BACKGROUND: Chromium-tanned leather articles currently constitute the most important cause of contact allergy to chromium in Denmark. A regulation on the content of hexavalent chromium in leather was adopted in November 2013 by the EU member states. OBJECTIVES: To characterize patients...... with chromium allergy and their disease, to serve as a baseline for future studies on the potential effect of the new regulation on chromium in leather. METHODS: A questionnaire case-control study was performed on 155 dermatitis patients with positive patch test reactions to potassium dichromate and a matched...... control group of 621 dermatitis patients. Comparisons were made by use of a χ(2) -test and the Mann-Whitney U-test. Logistic regression analyses were used to test for associations. RESULTS: Sixty-six per cent of chromium-allergic patients had a positive history of contact dermatitis caused by leather...

  13. Chromium in diet

    Science.gov (United States)

    The best source of chromium is brewer's yeast. However, many people do not use brewer's yeast because it causes bloating ( abdominal distention ) and nausea . Other good sources of chromium include ...

  14. Chromium and Genomic Stability

    OpenAIRE

    Wise, Sandra S.; Wise, John Pierce

    2011-01-01

    Many metals serve as micronutrients which protect against genomic instability. Chromium is most abundant in its trivalent and hexavalent forms. Trivalent chromium has historically been considered an essential element, though recent data indicate that while it can have pharmacological effects and value, it is not essential. There are no data indicating that trivalent chromium promotes genomic stability and, instead may promote genomic instability. Hexavalent chromium is widely accepted as high...

  15. A Green Approach to the Synthesis of Biologically Important Indeno[2,1-e]pyrazolo[5,4-b]pyridines via Microwave-assisted Multi-component Reactions in Water

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    A green approach to the synthesis of biologically important indeno[2,1-e]pyrazolo[5,4-b]pyridines was suc-cessfully realized via multi-component reactions of aldehyde, 3-methyl-l-phenyl-1H-pyrazol-5-amine and 1,3-indanedione in water under microwave irradiation without catalyst. This protocol has the prominent advantages of environmental-friendliness, short reaction time, excellent yields, low cost, easy operation as well as broad scope of applicability.

  16. Processes affecting the remediation of chromium-contaminated sites.

    OpenAIRE

    Palmer, C.D.; Wittbrodt, P R

    1991-01-01

    The remediation of chromium-contaminated sites requires knowledge of the processes that control the migration and transformation of chromium. Advection, dispersion, and diffusion are physical processes affecting the rate at which contaminants can migrate in the subsurface. Heterogeneity is an important factor that affects the contribution of each of these mechanisms to the migration of chromium-laden waters. Redox reactions, chemical speciation, adsorption/desorption phenomena, and precipitat...

  17. AEROSOL BEHAVIOR IN CHROMIUM WASTE INCINERATION

    Institute of Scientific and Technical Information of China (English)

    Suyuan Yu

    2003-01-01

    Cr2O3 is considered as the dominant incineration product during the combustion disposal of chromium waste. A hydrogen/air diffusion flame was employed to simulate the industrial process of incineration. Cr2O3 aerosols were generated inside the flame by the gas phase reaction of chromium and oxygen. Chromium came from the rapid decomposition of chromium hexacarbonyl (Cr(CO)6) at room temperature and was carried into the combustion chamber by hydrogen. Aerosol and clusters can then be easily formed in the flame by nucleation and coagulation. A two dimensional Discrete-Sectional Model (DSM) was adopted to calculate the Cr2O3 aerosol behavior. The experimental measurement method was Dynamic Light Scattering. The numerically predicted results agreed well with those of the experimental measurement. Both results show that the Cr2O3 aerosol size reached about 70 nanometers at the flame top.

  18. Spin-flip (p,n) reactions on 26Mg, 54Fe, and 56Fe at selected proton bombarding energies in the range of 17 to 25 MeV

    International Nuclear Information System (INIS)

    New data are presented for the 26Mg(p,n)26Al reaction at E/sub p/ = 19.12 and 24.97 MeV, for the 54Fe(p,n)54Co reaction at E/sub p/ = 17.20, 18.60, and 24.60 MeV, and for the 56Fe(p,n)56Co reaction at E/sub p/ = 19.12 and 24.59 MeV. Data were taken with the LLNL Cyclograaff at 16 angles from 3.50 to 159.00. A large detector at 23.80 with a long neutron flight path collected high resolution spectra. This large detector also collected separate 00 high resolution data on the 26Mg and 56Fe(p,n) reactions at E/sub p/ = 19 MeV. Absolute differential (p,n) cross sections were extracted for 1+ states in 26Al, 54Co, and 56Co, for the 0+ isobaric analong state (IAS) in 54Co and 56Co, for a 2+ state in each residual nucleus, and for the 0.199 MeV 7+ state of 54Co. No new experimental states were identified. Only relative cross sections were extracted at 00. Experimental angle-integrated cross sections were obtained for all but one state. DWBA79 was used, with the G-matrix effective nucleon-nucleon interaction of Bertsch et al. (with the central triplet-odd component V/sub to/ = O) and the Livermore shell model wave functions to calculate differential (p,n) cross sections to 1+ states and to the 54Co and 56Co IAS. Normalization of the DWBA angle-integrated cross sections to measurements for the 54Co and 56Co IAS (at E/sub p/ = 24.6 MeV) yielded the renormalized V/sub tau/ = 21.4 +- 2.1 MeV. Normalization of the DWBA angle-integrated cross sections to measurements for the 24.6 MeV 54Co and 56Co 1+ states, coupled with the normalization of the wave functions to previously experimentally determined GT strength, yield the renormalized V/sub sigmatau/ = 12.3 +- 1.2 MeV. The experimental Gamow-Teller strength B(GT)/sub exp./ of the T = 1 26Al state at 9.44 MeV was found to be 0.69; B(GT)/sub exp/ of the T = 1 26Al state at 10.47 MeV was found to be 0.39

  19. Influence of Chelating Agents on Chromium Fate in Sediment

    Institute of Scientific and Technical Information of China (English)

    WANGXIAOCHANG; SUNJINHE; 等

    1996-01-01

    A laboratory investigation on reaction between chelating agents and chromium was conducted to evaluate the effect of chelating agents on the adsorption and desorption of chromium in sediment.The amount of adsorbed chromium(VI) in sediment decreased slightly by 5%-10% because of addition of chelating agents.Chelating agents inhibited the removal of Cr(Ⅲ)by sediment from solutions and the inhibiting effect was in the order:citric acid>tartaric acid>EDTA,Salicylic acid.No effect of chelating agents on desorption of chromium in sediment was observed.

  20. Effect of polyethylene glycol on electrochemically deposited trivalent chromium layers

    Institute of Scientific and Technical Information of China (English)

    Joo-Yul LEE; Man KIM; Sik-Chol KWON

    2009-01-01

    The structural characteristics of the trivalent chromium deposits and their interfacial behavior in the plating solution with and without polyethylene glycol molecules were observed by using various electrochemical methods such as cyclic voltammetry, open circuit potential transition, electrochemical impedance spectroscopy, scanning electron microscopy and X-ray photoelectron spectrometry. It is shown that the polyethylene glycol molecules make the reductive current density lower in the trivalent chromium plating system and promote a hydrogen evolution reaction through their adsorption on the electrode surface. And the trivalent chromium layer formed from the polyethylene glycol-containing solution has somewhat higher density of cracks on its surface and results in a lower film resistance, lower polarization resistance, and higher capacitance in a corrosive atmosphere. It is also revealed that the formation of chromium carbide layer is facilitated in the presence of polyethylene glycol, which means easier electrochemical codeposition of chromium and carbon, not single chromium deposition.

  1. Coexistance of C40 and C54 TiSi2 during the solid state reaction of Ti/Mo/Si system

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The effect of a 0.9 nm Mo interlayer at the interface of Ti film depositedon a Si substrate on phase formation of TiSi2 during annealing has been studiedby using transmission electron micro-diffraction technique. When Ti/Mo/Si was an-nealed at low temperature as 550℃ for 30 min in Ar ambient, a metastable phase, i.e.,hexagonal C40 TiSi2, and the equilibrium phase, i.e., orthorhombic C54 TiSi2, wereboth detected. The experimental patterns of the C40 and C54 compare well with thesimulated ones.

  2. Synthesis of chromium containing pigments from chromium galvanic sludges.

    Science.gov (United States)

    Andreola, F; Barbieri, L; Bondioli, F; Cannio, M; Ferrari, A M; Lancellotti, I

    2008-08-15

    In this work the screening results of the scientific activity conducted on laboratory scale to valorise chromium(III) contained in the galvanic sludge as chromium precursor for ceramic pigments are reported. The valorisation of this waste as a secondary raw material (SRM) is obtained by achievement of thermal and chemical stable crystal structures able to color ceramic material. Two different pigments pink CaCr(0.04)Sn(0.97)SiO(5) and green Ca(3)Cr(2)(SiO(4))(3) were synthesized by solid-state reactions using dried Cr sludge as chromium oxide precursor. The obtained pigments were characterized by X-ray diffraction and SEM analysis. Furthermore the color developed in a suitable ceramic glaze was investigated in comparison with the color developed by the pigments prepared from pure Cr(2)O(3). The characterization carried out corroborates the thermal and chemical stability of the synthesized pigments and, especially for the Cr-Sn pink pigment, the powders develop an intense color that is very similar to the color developed by the pigments obtained starting from pure Cr(2)O(3). PMID:18289775

  3. Synthesis of chromium containing pigments from chromium galvanic sludges

    Energy Technology Data Exchange (ETDEWEB)

    Andreola, F.; Barbieri, L. [Dipartimento di Ingegneria dei Materiali e dell' Ambiente, Universita di Modena e Reggio Emilia, Via Vignolese 905, 41100 Modena (Italy); Bondioli, F. [Dipartimento di Ingegneria dei Materiali e dell' Ambiente, Universita di Modena e Reggio Emilia, Via Vignolese 905, 41100 Modena (Italy)], E-mail: bondioli.federica@unimore.it; Cannio, M. [Dipartimento di Ingegneria dei Materiali e dell' Ambiente, Universita di Modena e Reggio Emilia, Via Vignolese 905, 41100 Modena (Italy); Ferrari, A.M. [Dipartimento di Scienza e Metodi dell' Ingegneria, Universita di Modena e Reggio Emilia, Viale Amendola 2, 42100 Reggio Emilia (Italy); Lancellotti, I. [Dipartimento di Ingegneria dei Materiali e dell' Ambiente, Universita di Modena e Reggio Emilia, Via Vignolese 905, 41100 Modena (Italy)

    2008-08-15

    In this work the screening results of the scientific activity conducted on laboratory scale to valorise chromium(III) contained in the galvanic sludge as chromium precursor for ceramic pigments are reported. The valorisation of this waste as a secondary raw material (SRM) is obtained by achievement of thermal and chemical stable crystal structures able to color ceramic material. Two different pigments pink CaCr{sub 0.04}Sn{sub 0.97}SiO{sub 5} and green Ca{sub 3}Cr{sub 2}(SiO{sub 4}){sub 3} were synthesized by solid-state reactions using dried Cr sludge as chromium oxide precursor. The obtained pigments were characterized by X-ray diffraction and SEM analysis. Furthermore the color developed in a suitable ceramic glaze was investigated in comparison with the color developed by the pigments prepared from pure Cr{sub 2}O{sub 3}. The characterization carried out corroborates the thermal and chemical stability of the synthesized pigments and, especially for the Cr-Sn pink pigment, the powders develop an intense color that is very similar to the color developed by the pigments obtained starting from pure Cr{sub 2}O{sub 3}.

  4. Toxicity and adaptation of Dictyosphaerium chlorelloides to extreme chromium contamination.

    Science.gov (United States)

    Sánchez-Fortún, Sebastián; López-Rodas, Victoria; Navarro, Macarena; Marvá, Fernando; D'ors, Ana; Rouco, Mónica; Haigh-Florez, David; Costas, Eduardo

    2009-09-01

    Metals are often spilled by industries into inland water environments, with adverse consequences. Numerous papers have reported that heavy metals produce massive destruction of algae. Nevertheless, algal populations seem to become tolerant when they have had previous exposures to heavy metals. Because the mechanisms allowing heavy metal tolerance of algae are not yet known, the present study analyzed the effect of hexavalent chromium on growth and photosynthetic performance of Dictyosphaerium chlorelloides, stressing on the adaptation mechanisms to chromium contamination. Growth and photosynthetic performance of algal cells were inhibited by Cr(VI) at 10 mg/L, and the 72-h median inhibition concentration was established as 1.64 and 1.54 mg/L, respectively. However, after further incubation for a three month period in an environment with 25 mg/L of chromium, some rare, chromium-resistant cells occasionally were found. A Luria-Delbrück fluctuation analysis was performed to distinguish between resistant algae arising from rare, spontaneous mutations and resistant algae arising from physiological adaptation and other adaptive mechanisms. Resistant cells arose only by spontaneous mutations before the addition of chromium, with a rate of 1.77 x 10(-6) mutants per cell division. From a practical point of view, the use of both chromium-sensitive and chromium-resistant genotypes could make possible a specific algal biosensor for chromium. PMID:19323601

  5. The carcinogenicity of chromium

    OpenAIRE

    Norseth, Tor

    1981-01-01

    The carcinogenicity of chromium compounds is reviewed with specific attention to the gaps in knowledge for risk estimation and research needs. The most important problems at present are whether trivalent chromium compounds cause cancer, and whether there is a difference in cancer causing effects between the soluble and the slightly soluble hexavalent compounds in the practical exposure situation. Dose estimates for risk estimation based on epidemiological investigations are also lacking. Pres...

  6. Study of the e+e- → μ+μ-γ reaction at center-of-mass energies between 54 and 64 GeV

    International Nuclear Information System (INIS)

    The cross section and forward-backward muon charge asymmetry for the e+e-→μ+μ-γ reaction were measured to be σ = 2.82 ± 0.35 pb and A = 0.34 ± 0.10 with the VENUS detector at TRISTAN at = 59.2 GeV for an integrated luminosity of 53.5 pb-1. The measured cross section agrees with the theoretical prediction. The asymmetry result is consistent with the electroweak prediction but not with the QED prediction at the level of 2σ. (orig.)

  7. Obtaining decorative chromium plating from trivalent chromium solutions

    OpenAIRE

    Óscar Javier Suárez García

    2010-01-01

    The present work was aimed at a qualitative evaluation, in the laboratory, of different alternatives for assembling and operating a trivalent chromium bath for decorative chromium plating. Different chromium concentration solutions and different complexing agents were used. The initial result of this analysis was that chloride, formate and acetate solutions produced the best results. Solution preparation conditions were evaluated: temperature, chromium III complex formation time and also ...

  8. Skin permeation and cutaneous hypersensitivity as a basis for making risk assessments of chromium as a soil contaminant.

    OpenAIRE

    Bagdon, R E; Hazen, R E

    1991-01-01

    A literature review of experimental and human exposure studies of skin permeation and cutaneous hypersensitivity reactions evoked by chromium was carried out to provide a basis for making a risk assessment of chromium as a soil contaminant. In vitro and in vivo studies demonstrated that 1 to 4% of the applied dose of hexavalent and trivalent chromium to guinea pig skin penetrated skin within 5 to 24 hr after application. Ultrastructural investigations showed that hexavalent chromium localized...

  9. Chromium reduction from slag on electromelting of stainless steel

    International Nuclear Information System (INIS)

    Specific features of chromium reduction from the slag on electromelting of stainless steel type Kh18N10T according to one- or two-slag procedure were studied. It was shown that one-slag melting technology allows double decrease of chromium losses in the form of incompletely reduced oxides. This occurs due to additional chemical reactions between metal and slag on their combined pouring into the ladle. 1 ref.; 3 figs

  10. The analytical biochemistry of chromium.

    OpenAIRE

    Katz, S A

    1991-01-01

    The essentiality and carcinogenicity of chromium depend on its chemical form. Oxidation state and solubility are particularly important in determining the biological effects of chromium compounds. For this reason, total chromium measurements are of little value in assessing its nutritional benefits or its toxicological hazards. Aqueous sodium carbonate-sodium hydroxide solutions have been successfully used for extracting hexavalent chromium from a variety of environmental and biological matri...

  11. Structure and morphology studies of chromium film at elevated temperature in hypersonic environment

    Indian Academy of Sciences (India)

    G M Hegde; V Kulkarni; M Nagaboopathy; K P J Reddy

    2012-06-01

    This paper presents the after shock heated structural and morphological studies of chromium film coated on hypersonic test model as a passive drag reduction element. The structural changes and the composition of phases of chromium due to shock heating (2850 K) are characterized using X-ray diffraction studies. Surface morphology changes of chromium coating have been studied using scanning electron microscopy (SEM) before and after shock heating. Significant amount of chromium ablation and sublimation from the model surface is noticed from SEM micrographs. Traces of randomly oriented chromium oxides formed along the coated surface confirm surface reaction of chromium with oxygen present behind the shock. Large traces of amorphous chromium oxide phases are also observed.

  12. Chromium in potatoes

    International Nuclear Information System (INIS)

    Chromium concentration in potatoes was determined, and tubes were labeled either intrinsically or extrinsically with radioactive chromate (51Cr). A labeled chromium complex was isolated from preparations of raw, baked, or fried potatoes and chromatographed on gel permeation media. Potato pulp and peel contained 1.63 and 2.70 μg of Cr/g tissue, respectively. There was no correlation between the two, nor did they respond similarly to changes of variety or locations. No significant differences were apparent in relative migration of the isolated complexes except between raw and cooked extrinsically labeled preparations

  13. CHROMIUM(II) AMIDES - SYNTHESIS AND STRUCTURES

    NARCIS (Netherlands)

    EDEMA, JJH; GAMBAROTTA, S; MEETSMA, A; SPEK, AL; SMEETS, WJJ; CHIANG, MY

    1993-01-01

    A novel class of mono- and di-meric chromium(II) amides has been prepared and characterized. Reaction of [CrCl2(thf)2] (thf = tetrahydrofuran) with 2 equivalents of M(NR2) (R = C6H11, Pr(i), Ph, or phenothiazinyl; M = Li or Na) allowed the formation of the homoleptic amides [{Cr(mu-NR2)(NR2)}2] (R =

  14. Production of basic chromium sulfate by using recovered chromium from ashes of thermally treated leather.

    Science.gov (United States)

    Dettmer, Aline; Nunes, Keila Guerra Pacheco; Gutterres, Mariliz; Marcílio, Nilson Romeu

    2010-04-15

    Leather wastes tanned with chromium are generated during the production process of leather, hence the wastes from hand crafted goods and footwear industries are a serious environmental problem. The thermal treatment of leather wastes can be one of the treatment options because the wastes are rich in chromium and can be used as a raw material for sodium chromate production and further to obtain several chromium compounds. The objective of this study was to utilize the chromium from leather wastes via basic chromium sulfate production to be subsequently applied in a hide tanning. The obtained results have shown that this is the first successful attempt to achieve desired base properties of the product. The result was achieved when the following conditions were applied: a molar ratio between sodium sulfite and sodium dichromate equal to 6; reaction time equal to 5 min before addition of sulfuric acid; pH of sodium dichromate solution equal to 2. Summarizing, there is an opportunity to utilize the dangerous wastes and reused them in the production scheme by minimizing or annulling the environmental impact and to attend a sustainable process development concept.

  15. Production of basic chromium sulfate by using recovered chromium from ashes of thermally treated leather.

    Science.gov (United States)

    Dettmer, Aline; Nunes, Keila Guerra Pacheco; Gutterres, Mariliz; Marcílio, Nilson Romeu

    2010-04-15

    Leather wastes tanned with chromium are generated during the production process of leather, hence the wastes from hand crafted goods and footwear industries are a serious environmental problem. The thermal treatment of leather wastes can be one of the treatment options because the wastes are rich in chromium and can be used as a raw material for sodium chromate production and further to obtain several chromium compounds. The objective of this study was to utilize the chromium from leather wastes via basic chromium sulfate production to be subsequently applied in a hide tanning. The obtained results have shown that this is the first successful attempt to achieve desired base properties of the product. The result was achieved when the following conditions were applied: a molar ratio between sodium sulfite and sodium dichromate equal to 6; reaction time equal to 5 min before addition of sulfuric acid; pH of sodium dichromate solution equal to 2. Summarizing, there is an opportunity to utilize the dangerous wastes and reused them in the production scheme by minimizing or annulling the environmental impact and to attend a sustainable process development concept. PMID:20031309

  16. Dimensionally Controlled Lithiation of Chromium Oxide

    Energy Technology Data Exchange (ETDEWEB)

    Fister, Tim T. [Argonne National Lab. (ANL), Argonne, IL (United States); Hu, Xianyi [Northwestern Univ., Evanston, IL (United States); Esbenshade, Jennifer [Univ. of Illinois, Urbana-Champaign, IL (United States); Chen, Xiao [Northwestern Univ., Evanston, IL (United States); Wu, Jinsong [Northwestern Univ., Evanston, IL (United States); Dravid, Vinayak [Northwestern Univ., Evanston, IL (United States); Bedzyk, Michael [Northwestern Univ., Evanston, IL (United States); Long, Brandon [Argonne National Lab. (ANL), Argonne, IL (United States); Gewirth, Andrew A. [Univ. of Illinois, Urbana-Champaign, IL (United States); Shi, Bing [Argonne National Lab. (ANL), Argonne, IL (United States); Schlepütz, Christian M. [Argonne National Lab. (ANL), Argonne, IL (United States); Fenter, Paul [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-01-12

    Oxide conversion reactions are an alternative approach for high capacity lithium ion batteries but are known to suffer from structural irreversibility associated with the phase separation and reconstitution of reduced metal species and Li2O. In particular, the morphology of the reduced metal species is thought to play a critical role in the electrochemical properties of a conversion material. Here we use a model electrode with alternating layers of chromium and chromium oxide to better understand and control these phase changes in real-time and at molecular length scales. Despite lacking crystallinity at the atomic scale, this superstructure is observed (with X-ray reflectivity, XR) to lithiate and delithiate in a purely one-dimensional manner, preserving the layered structure. The XR data show that the metal layers act as nucleation sites for the reduction of chromium in the conversion reaction. Irreversibility during delithiation is due to the formation of a ternary phase, LiCrO2, which can be further delithiated at higher potentials. The results reveal that the combination of confining lithiation to nanoscale sheets of Li2O and the availability of reaction sites in the metal layers in the layered structure is a strategy for improving the reversibility and mass transport properties that can be used in a wide range of conversion materials.

  17. Chromium(VI) transport and fate in unsaturated zone and aquifer: 3D Sandbox results.

    Science.gov (United States)

    Zhao, Xingmin; Sobecky, Patricia A; Zhao, Lanpo; Crawford, Patrice; Li, Mingtang

    2016-04-01

    The simulation of Cr(VI) behavior in an unsaturated zone and aquifer, using a 3D experimental set-up were performed to illustrate the distribution, transport and transformation of Cr(VI), and further to reveal the potential harm of Cr(VI) after entering the groundwater. The result indicated that chromium(VI) was transported in the vertical direction, meanwhile, was transported in the horizontal direction under the influence of groundwater flow. The direction and distance away from the pollution source zone had great effect on the chromium(VI) concentration. At the sampling sites near the pollution source zone, there was a sudden increase of chromium(VI) concentration. The concentration of chromium(III) concentration in some random effluent samples was not detected. Chromium had not only transported but also had fraction and specie transformation in the unsaturated zone and aquifer. The relative concentration of residue fraction chromium was decreased with time. The content of Fe-Mn oxide fraction chromium was increased with time. The relative content of exchangeable and carbonate-bound fraction chromium was lower and the content variations were not obvious. Chromium(VI) (91-98%) was first reduced to chromium(III) rapidly. The oxidation reaction occurred later and the relative content of chromium(VI) was increased again. The presence of manganese oxides under favorable soil conditions can promote the reoxidation of Cr(III) to Cr(VI).

  18. Evaluation of Some (n,n'), (n,γ), (n,p), (n,2n) and (n,3n) Reaction Excitation Functions for Fission and Fusion Reactor Dosimetry Applications; Evaluation of the Excitation Functions for the 54Fe(n,p)54Mn, 58Ni(n,2n)57Ni, 67Zn(n,p)67Cu, 92Mo(n,p)92mNb, 93Nb(n,γ)94Nb, 113In(n,n')113mIn, 115In(n,γ) 116mIn, and 169Tm(n,3n)167Tm Reactions. Progress Report on Research Contract No 16242

    International Nuclear Information System (INIS)

    Cross section data for the 54Fe(n,p)54Mn, 58Ni(n,2n)57Ni, 67Zn(n,p)67Cu, 92Mo(n,p)92mNb, 93Nb(n,γ)94Nb, 113In(n,n')113mIn, 115In(n,γ)116mIn, 169Tm(n,3n)167Tm reactions are needed to solve a wide spectrum of scientific and technical tasks. Activation detectors based on these reactions may be used in the field of reactor dosimetry. Furthermore, the 54Fe(n,p)54Mn reaction is often used in experimental nuclear physics as a monitor reaction for measurements of unknown cross sections by means of the activation method over the neutron energy range from 5 to 15 MeV. The 93Nb(n,γ)94Nb reaction is also very promising for using in retrospective neutron dosimetry for determination of total neutron fluence during a campaign of a reactor. In the existing version of the International Reactor Dosimetry File and the new extended version named as IRDFF data for excitation functions of 67Zn(n,p)67Cu, 92Mo(n,p)92mNb, 113In(n,n')113mIn, and 169Tm(n,3n)167Tm reactions are absent. Data for these reactions are also absent in the JENDL/D-99 dosimetry file. Excitation functions of 67Zn(n,p)67Cu and 169Tm(n,3n)167Tm are presented in the TENDL-2012, EAF-2010, JENDL-4.0, JEFF-3.1/A, MENDL-2 libraries. Cross section data for the 67Zn(n,p)67Cu reaction up to 20 MeV are given also in the JENDL/HE-2007 library. Excitation functions of the 92Mo(n,p)92mNb and 113In(n,n')113mIn reactions are evaluated in the EAF-2010 and JEFF-3.1/A libraries. Cross section data for the 113In(n,n')113mIn reaction are given also in the TENDL-2010 library. It is necessary to note that neutron data in the JEFF-3.1/A and JENDL-4.0 libraries were evaluated up to 20 MeV. Neutron data in the TENDL-2012, EAF-2010, MENDL-2 and TENDL-2010 libraries had been evaluated up to 30 MeV, 60 MeV, 100 MeV and 200 MeV, respectively. Neutron cross sections in the MENDL-2, TENDL-2010 and TENDL-2012 libraries had been obtained on the basis of pure theoretical model calculations and are not appropriate for reactor and fusion dosimetry

  19. Groundwater contaminant by hexavalent chromium

    Energy Technology Data Exchange (ETDEWEB)

    Parsons, C. [Univ. of Texas, Austin, TX (United States)

    1995-11-01

    Oxidation of trivalent chromium to hexavalent chromium has been investigated as a function of total manganese in soils as well as various incubation conditions. Chromium and manganese contents were analyzed by atomic absorption (graphite furnace and flame emission respectively) following acid digestion. Total hexavalent chromium generation capacity was determined by addition of 0.001 M CrCL3, incubation, and analysis by s-diphenyl carbazide. Samples were then leached with CaSO{sub 4} and MgSO{sub 4} and incubated in various environments (oven, freeze-drier, field moist, ultrafreeze) to test for geogenic generation of Cr(IV). The degree of geogenic generation of hexavalent chromium was compared with total Mn and Cr content as well as hexavalent generational capacity.

  20. Electron transfer. 75. Reduction of carboxylato-bound chromium(V) with vanadium(IV). Intervention of chromium(IV)

    International Nuclear Information System (INIS)

    The chelated (carboxylato)chromium(V) anion bis(2-hydroxy-2-ethylbutyrato)oxochromate(V) (I), [(Lig)2Cr(O)]-, reacts with oxovanadium(IV) to form a strongly absorbing species (lambda/sub max/ = 515 nm; epsilon = 1.7 x 103 M-1) in the presence of 2-hydroxy-2-ethylbutyric acid buffers (pH 2-4). EPR data support 1:1 stoichiometry with VO2+ in deficiency, indicating the formation of a chromium(IV) species by reduction. With excess VO2+ a chromium(III) product was obtained. Spectral and ion-exchange properties of this product correspond to those observed for the titanium(III) and iron(II) reductions of chromium(V) and are consistent with the formulation of the product as a bis(hydroxycarboxylate) chelate of (H2O)2Cr/sup III/. With excess vanadium(IV), the reaction exhibits triphasic kinetics. The remaining step of the reaction is the reduction of the chromium(IV) intermediate with VO2+. Rates for all steps increase with decreasing [H+] and level off at low [H+]. The limiting rate constants for the formation of the chromium(IV) intermediate by the (Lig)3Cr(O)2- and (Lig)2Cr(O)- pathways are 2.8 x 103 and 2.2 x 102 M-1s-1. The bimolecular limiting rate constant for the reduction of chromium(IV) is computed to be 7.7 x 102 M-1 s-1. 33 references, 7 tables

  1. Determination of total chromium in tanned leather samples used in car industry.

    Science.gov (United States)

    Zeiner, Michaela; Rezić, Iva; Ujević, Darko; Steffan, Ilse

    2011-03-01

    Despite the high competition of synthetic fibers leather is nowadays still widely used for many applications. In order to ensure a sufficient stability of the skin matrix against many factors, such as microbial degradation, heat and sweat, a tanning process is indispensable. Using chromium (III) for this purpose offers a multitude of advantages, thus this way of tanning is widely applied. During the use of chromium tanned leather as clothing material as well as for decoration/covering purposes, chromium is extracted from the leather and may then cause nocuous effects to human skin, e.g. allergic reactions. Thus the knowledge of the total chromium content of leather samples expected to come into prolonged touch with human skin is very important. In car industry leather is used as cover for seats, steering wheel and gearshift lever The chromium contents often chromium tanned leather samples used in car industry were determined. First all samples were dried at 65 degrees C overnight and then cut in small pieces using a ceramic knife, weighed and analyzed by inductively coupled plasma--optical emission spectrometry (ICP-OES) after acidic microwave assisted digestion. The total chromium amounts found were in the range from 19 mg/g up to 32 mg/g. The extraction yield of chromium from leather samples in sweat is approximately 2-7%. Thus especially during long journeys in summer chromium can be extracted in amounts which may cause nocuous effects for example on the palm of the hands or on the back.

  2. Chromium trace determination in inorganic, organic and aqueous samples with isotope dilution mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Goetz, A.; Heumann, K.G.

    1988-06-01

    It is shown that chromium traces in different inorganic, organic and aqueous samples can be determined over a wide concentration range with isotope dilution mass spectrometry. Electrolytic or chromatographic isolation steps are added to a system of sample preparation units for oligo-element determinations to analyse chromium besides other heavy metals. The isotope ratio /sup 52/Cr//sup 53/Cr is measured in a thermal quadrupole mass spectrometer using a single-filament ion source with additions of silica gel and boric acid. In water samples, which contain humic substances, chromium concentrations of a few ng/g and less can be determined with relative standard deviations of about 1% and better. A differentiation is possible into the total chromium content and into chromium species which carry out isotope exchange reactions and those which are inert for an isotope exchange reaction. The chromium concentrations of four standard reference materials (two plants BCR 60 and 61, one tissue BCR 278, one sewage sludge BCR 144), which are not certified for chromium, are determined to be 29.4 ..mu..g/g, 534 ..mu..g/g, 0.78 ..mu..g/g, and 466.1 ..mu..g/g, respectively. In three different sediments total chromium concentrations between 100 ..mu..g/g and 180 ..mu..g/g are analysed with relative standard deviations of 0.6%-1.2%.

  3. Chromium reduction in Pseudomonas putida.

    OpenAIRE

    Ishibashi, Y.; Cervantes, C; Silver, S

    1990-01-01

    Reduction of hexavalent chromium (chromate) to less-toxic trivalent chromium was studied by using cell suspensions and cell-free supernatant fluids from Pseudomonas putida PRS2000. Chromate reductase activity was associated with soluble protein and not with the membrane fraction. The crude enzyme activity was heat labile and showed a Km of 40 microM CrO4(2-). Neither sulfate nor nitrate affected chromate reduction either in vitro or with intact cells.

  4. Chronic occupational exposure to hexavalent chromium causes DNA damage in electroplating workers

    Directory of Open Access Journals (Sweden)

    Ren Xiao-Bin

    2011-04-01

    Full Text Available Abstract Background Occupational exposure to chromium compounds may result in adverse health effects. This study aims to investigate whether low-level hexavalent chromium (Cr(VI exposure can cause DNA damage in electroplating workers. Methods 157 electroplating workers and 93 control subjects with no history of occupational exposure to chromium were recruited in Hangzhou, China. Chromium levels in erythrocytes were determined by graphite furnace atomic absorption spectrophotometer. DNA damage in peripheral lymphocytes was evaluated with the alkaline comet assay by three parameters: Olive tail moment, tail length and percent of DNA in the comet tail (tail DNA%. Urinary 8-OHdG levels were measured by ELISA. Results Chromium concentration in erythrocytes was about two times higher in electroplating workers (median: 4.41 μg/L than that in control subjects (1.54 μg/L, P P P P Conclusion The findings in this study indicated that there was detectable chromium exposure in electroplating workers. Low-level occupational chromium exposure induced DNA damage.

  5. STS-54 Crew Portrait

    Science.gov (United States)

    1992-01-01

    Astronauts pictured in the STS-54 crew portrait from left to right are: Mario Runco, Jr., mission specialist; John H. Casper, commander; Donald R. McMonagle, pilot; and mission specialists Susan J. Helms, and Gregory J. Harbaugh. Launched aboard the Space Shuttle Endeavour on January 13, 1993 at 8:59:30 am (EST), the crew deployed the fifth Tracking and Data Relay Satellite (TDRS-6).

  6. Hexavalent chromium removal from wastewater using aniline formaldehyde condensate coated silica gel.

    Science.gov (United States)

    Kumar, P Albino; Ray, Manabendra; Chakraborty, Saswati

    2007-05-01

    A resinous polymer, aniline formaldehyde condensate (AFC) coated on silica gel was used as an adsorbent in batch system for removal of hexavalent chromium from aqueous solution by considering the effects of various parameters like reaction pH, dose of AFC coated silica gel, initial Cr(VI) concentration and aniline to formaldehyde ratio in AFC synthesis. The optimum pH for total chromium [Cr(VI) and Cr(III)] adsorption was observed as 3. Total chromium adsorption was second order and equilibrium was achieved within 90-120 min. Aniline to formaldehyde ratio of 1.6:1 during AFC synthesis was ideal for chromium removal. Total chromium adsorption followed Freundlich's isotherm with adsorption capacity of 65 mg/g at initial Cr(VI) 200mg/L. Total chromium removal was explained as combinations of electrostatic attraction of acid chromate ion by protonated AFC, reduction of Cr(VI) to Cr(III) and bond formation of Cr(III) with nitrogen atom of AFC. Almost 40-84% of adsorbed chromium was recovered during desorption by NaOH, EDTA and mineral acids. AFC coated silica gel can be effectively used for treatment of chromium containing wastewaters as an alternative.

  7. Effect of some non functional surfactants and electrolytes on the hexavalent chromium reduction by glycerol. A mechanistic study

    Energy Technology Data Exchange (ETDEWEB)

    Basu, A.; Ghosh, S.K.; Saha, R.; Nandi, R.; Saha, B. [Burdwan Univ., WB (India). Dept. of Chemistry; Gosh, T. [A.B.N. Seal College, Coochbehar, WB (India). Dept. of Chemistry

    2011-11-15

    Hexavalent chromium is a widespread environmental contaminant and a known human carcinogen. Kinetics of reduction of hexavalent chromium by bio-molecule glycerol in micellar media have been studied spectrophotometrically. The cytoplasmic reduction of hexavalent chromium to trivalent chromium occurs in micro-heterogeneous systems. In vitro, the micelles are considered to mimic the cellular membranes. The electron transfer processes occurring in the micellar systems is considered as model to obtain insight into the electron transport process prevailing in biological systems. Micellar media is also a probe to establish the mechanistic paths of reduction of hexavalent chromium to trivalent chromium. Effects of electrolytes common to biological system are studied to establish the proposed reaction mechanism strongly. (orig.)

  8. Galvanic cells including cobalt-chromium alloys.

    Science.gov (United States)

    Gjerdet, N R

    1980-01-01

    Galvanic cells may be created when dentures made of cobalt-chromium alloys are placed on teeth with metallic restorations. The power of such cells was evaluated in an in vitro galvanic using amalgams, gold alloy, and nickel-chromium alloys. The amalgams and one of the nickel-chromium alloys revealed high corrosion currents when placed in contact with cobalt-chromium alloy, the conventional amalgam showing the highest values. The gold alloy and another nickel-chromium alloy exhibited low corrosion currents and they were noble with respect to cobalt-chromium.

  9. Hydrogen permeation through chromium

    International Nuclear Information System (INIS)

    Steady state and non-steady state measurements of hydrogen permeation through metallic chromium are reported. The experiments have been conducted by use of hydrogen and deuterium within a pressure range of 10-8 - 1 bar and temperatures between 600 - 8000C. Numerical values for the physical quantities permeability, diffusion constant and solubility could be derived. At an upstream pressure above around 10-3 bar classical Sieverts-low was found (permeation rate proportional √p) with activation energies Qsub(perm) = 65 kJoule/mole, Qsub(Diff) = 4-8 kJoule/mole, Qsub(Sol) = 57-61 kJoule/mole for the respective processes involved. The isotopic effect between H and D of the permeabilities could be represented by a factor of 1,5 independence on temperature. All non steady-state measurements could be approximated reasonably well by classical diffusion kinetics. Below up-stream pressures of approx.= 10-7 bar the kinetics was no longer diffusion controlled, the dependence on up-stream pressure changed from √p -> p, the activation energy for permetation increased to 127 kJoule/mole and the isotopic factor resulted in about 2-3. (orig.)

  10. Characterisation of exposure to total and hexavalent chromium of welders using biological monitoring.

    NARCIS (Netherlands)

    Scheepers, P.T.J.; Heussen, G.A.; Peer, P.G.M.; Verbist, K.; Anzion, R.; Willems, J.

    2008-01-01

    Inhalation exposure to total and hexavalent chromium (TCr and HCr) was assessed by personal air sampling and biological monitoring in 53 welders and 20 references. Median inhalation exposure levels of TCr were 1.3, 6.0, and 5.4 microg/m(3) for welders of mild steel (MS, <5% alloys), high alloy st

  11. Ferrous sulphate mono and heptahydrate reduction of hexavalent chromium in cement: effectiveness and storability

    OpenAIRE

    Valverde, J. L.; Lobato, J.; I. Fernández; Marijuán, L.; Pérez-Mohedano, S.; Talero, R.

    2005-01-01

    In Community legislation, substances containing hexavalent chromium are classified as carcinogenic, mutagenic and sensitizing. In cement, hexavalent chromium intensifies sensitization and may set off severe allergic reactions in workers in routine contact with the product, whether in the factory or on construction sites. The allergic or contact dermatitis causes is a very painful disease that may lead to permanent worker disability. According to Directive 2003/53/EC of the European Parliament...

  12. MODELING THE RATE-CONTROLLED SORPTION OF HEXAVALENT CHROMIUM.

    Science.gov (United States)

    Grove, D.B.; Stollenwerk, K.G.

    1985-01-01

    Sorption of chromium VI on the iron-oxide- and hydroxide-coated surface of alluvial material was numerically simulated with rate-controlled reactions. Reaction kinetics and diffusional processes, in the form of film, pore, and particle diffusion, were simulated and compared with experimental results. The use of empirically calculated rate coefficients for diffusion through the reacting surface was found to simulate experimental data; pore or particle diffusion is believed to be a possible rate-controlling mechanism. The use of rate equations to predict conservative transport and rate- and local-equilibrium-controlled reactions was shown to be feasible.

  13. Neutron-rich chromium isotope anomalies in supernova nanoparticles

    CERN Document Server

    Dauphas, Nicolas; Chen, James; Roskosz, Mathieu; Papanastassiou, Dimitri; Stodolna, Julien; Guan, Yunbin; Ma, Chi; Eiler, John

    2010-01-01

    Neutron-rich isotopes with masses near that of iron are produced in type Ia and II supernovae. Traces of such nucleosynthesis are found in primitive meteorites in the form of variations in the isotopic abundance of 54Cr, the most neutron-rich stable isotope of chromium. The hosts of these isotopic anomalies must be presolar grains that condensed in the outflows of supernovae, offering the opportunity to study the nucleosynthesis of iron-peak nuclei in ways that complement spectroscopic observations and can inform models of stellar evolution. However, despite almost two decades of extensive search, the carrier of 54Cr anomalies is still unknown, presumably because it is fine-grained and is chemically labile. Here we identify in the primitive meteorite Orgueil the carrier of 54Cr-anomalies as nanoparticles, most likely spinels that show large enrichments in 54Cr relative to solar composition (54Cr/52Cr ratio >3.6xsolar). Such large enrichments in 54Cr can only be produced in supernovae. The mineralogy of the gr...

  14. Chromium(III) -- chromium(VI) interconversions in seawater

    NARCIS (Netherlands)

    Weijden, C.H. van der; Reith, M.

    1982-01-01

    The stable form of dissolved chromium in oxygenated seawater is Cr(VI). But Cr(III)-species are also present at an analytically significant level. It is shown that Cr(III) is oxidized only slowly by dissolved oxygen, and that manganese oxide is a strong catalyst for such oxidation. However, the low

  15. Investigation of the reactions (n,p) and (n,n'p) on 27Al, 28Si, 50Cr, 54Fe, 56Fe, 58Ni and Ni at 14.1 MeV neutron energy

    International Nuclear Information System (INIS)

    Investigation of the nuclear reactions (n,p) and (n,n'p) on 14 MeV neutrons, apart form its applied value, is also fundamental for correcting the systematics of cross-sections and other values, as well as for comparisons with models of nuclei and nuclear reactions. In this work the authors measured the energy and angular distributions of the products of the reactions (n,p) and (n,n'p) for elements contained in constructional materials. In addition, they determined the cross-sections of these reactions and compared them with the results of other works and recommended data. A charged-particle spectrometer was used in the experiment, the neutron source was a NG-200 generator, and the reaction employed was 3H(d,n)4He. (author). 24 refs, 8 figs, 2 tabs

  16. Iron monosulfide as a scavenger for dissolved hexavalent chromium and cadmium.

    Science.gov (United States)

    Jo, S; Lee, J Y; Kong, S H; Choi, J; Park, J W

    2008-09-01

    Iron sulfide minerals are common components of soil/sedimentary environments. Reactions near the surfaces of iron sulfides play important roles in metal retention, mobility, and bioavailability. A series of batch experiments was conducted to study the removal of aqueous chromium and cadmium by iron monosulfide. Hexavalent chromium was reduced to Cr(III) by iron monosulfide with simultaneous precipitation of chromium and iron oxyhydroxide. In contrast to chromium, the primary retention mechanism of cadmium by iron monosulfide was lattice exchange. Surface adsorption to iron monosulfide and precipitation with sulfide on the iron monosulfide surface also contributed to the removal of aqueous cadmium. New phases of both chromium and cadmium were confirmed with transmission electron microscopy. The solution pH was an important factor in this research; it can change particle surface charge and metal species, hence affecting the removal of chromium, but not cadmium. Ferrous ions without FeS exhibited less Cr(VI) removal than with FeS, which might be owing to sulfides from FeS and the existence of the solid phase. Iron monosulfide exhibited higher removal efficiency for chromium and cadmium than zero valent iron and other iron oxide minerals, and the synergistic effect of ferrous iron and sulfide appeared to cause this result.

  17. Determination of chromium combined with DNA, RNA and protein in chromium-rich brewer's yeast

    International Nuclear Information System (INIS)

    The contents of chromium in the DNA, RNA and protein fractions separated from chromium-rich and normal brewer's yeast were determined with the neutron activation analysis in order to study the combination of Cr with DNA, RNA and protein in chromium-rich brewer's yeast. The results showed that the extracting rats and concentrations of DNA, RNA and protein had no significant difference in two types of yeast, but the chromium contents of DNA, RNA and protein in the chromium-rich yeast were significantly higher than those in the normal. In addition, the content of chromium in DNA was much higher than that in RNA and protein, which indicated that the inorganic chromium compounds entered into the yeast cell, during the yeast cultivation in the culture medium containing chromium were converted into organic chromium compounds combined with DNA, RNA and protein

  18. The effect of chronic chromium exposure on the health of Chinook salmon (Oncorhynchus tshawytscha)

    Energy Technology Data Exchange (ETDEWEB)

    Farag, Aida M. [United States Geological Survey, Columbia Environmental Research Center, Jackson Field Research Station, P.O. Box 1089, Jackson, WY 83001 (United States)]. E-mail: aida_farag@usgs.gov; May, Thomas [United States Geological Survey, Columbia Environmental Research Center, Columbia, MO 65201 (United States); Marty, Gary D. [Department of Anatomy, Physiology, and Cell Biology, School of Veterinary Medicine, University of California, 1 Shields Ave., Davis, CA 95616-8732 (United States); Easton, Michael [International EcoGen Inc., 2015 McLallen Court, North Vancouver, BC, Canada V7P 3H6 (Canada); Harper, David D. [United States Geological Survey, Columbia Environmental Research Center, Jackson Field Research Station, P.O. Box 1089, Jackson, WY 83001 (United States); Little, Edward E. [United States Geological Survey, Columbia Environmental Research Center, Columbia, MO 65201 (United States); Cleveland, Laverne [United States Geological Survey, Columbia Environmental Research Center, Columbia, MO 65201 (United States)

    2006-03-10

    This study was designed to determine fish health impairment of Chinook salmon (Oncorhynchus tshawytscha) exposed to chromium. Juvenile Chinook salmon were exposed to aqueous chromium concentrations (0-266 {mu}g l{sup -1}) that have been documented in porewater from bottom sediments and in well waters near salmon spawning areas in the Columbia River in the northwestern United States. After Chinook salmon parr were exposed to 24 and 54 {mu}g Cr l{sup -1} for 105 days, neither growth nor survival of parr was affected. On day 105, concentrations were increased from 24 to 120 {mu}g Cr l{sup -1} and from 54 to 266 {mu}g Cr l{sup -1} until the end of the experiment on day 134. Weight of parr was decreased in the 24/120 {mu}g Cr l{sup -1} treatment, and survival was decreased in the 54/266 {mu}g Cr l{sup -1} treatment. Fish health was significantly impaired in both the 24/120 and 54/266 {mu}g Cr l{sup -1} treatments. The kidney is the target organ during chromium exposures through the water column. The kidneys of fish exposed to the greatest concentrations of chromium had gross and microscopic lesions (e.g. necrosis of cells lining kidney tububules) and products of lipid peroxidation were elevated. These changes were associated with elevated concentrations of chromium in the kidney, and reduced growth and survival. Also, variations in DNA in the blood were associated with pathological changes in the kidney and spleen. These changes suggest that chromium accumulates and enters the lipid peroxidation pathway where fatty acid damage and DNA damage (expressed as chromosome changes) occur to cause cell death and tissue damage. While most of the physiological malfunctions occurred following parr exposures to concentrations {>=}120 {mu}g Cr l{sup -1}, nuclear DNA damage followed exposures to 24 {mu}g Cr l{sup -1}, which was the smallest concentration tested. The abnormalities measured during this study are particularly important because they are associated with impaired growth

  19. Laboratory scale studies on removal of chromium from industrial wastes

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    Chromium being one of the major toxic pollutants is discharged from electroplating and chrome tanning processes and is also found in the effluents of dyes, paint pigments, manufacturing units etc. Chromium exists in aqueous systems in both trivalent (Cr 3+) and hexavalent (Cr 6+) forms. The hexavalent form is carcinogenic and toxic to aquatic life, whereas Cr3+ is however comparatively less toxic. This study was undertaken to investigate the total chromium removal from industrial effluents by chemical means in order to achieve the Pakistan NEQS level of 1 mg/L by the methods of reduction and precipitation. The study was conducted in four phases.In phase I, the optimum pH and cost effective reducing agent among the four popular commercial chemicals was selected. As a result, pH of 2 was found to be most suitable and sodium meta bisulfate was found to be the most cost effective reducing agent respectively. Phase II showed that lower dose of sodium meta bisulfate was sufficient to obtain 100 % efficiency in reducing Cr6+ to Cr3+, and it was noted that reaction time had no significance in the whole process. A design curve for reduction process was established which can act as a tool for treatment of industrial effluents.Phase III studies indicated the best pH was 8.5 for precipitation of Cr 3+ to chromium hydroxide by using lime. An efficiency of 100 % was achievable and a settling time of 30 minutes produced clear effluent. Finally in Phase IV actual waste samples from chrome tanning and electroplating industries, when precipitated at pH of 12 gave 100 % efficiency at a settling time of 30 minutes and confirmed that chemical means of reduction and precipitation is a feasible and viable solution for treating chromium wastes from industries.

  20. Brief report on thermodynamics of chromium slags and kinetic modelling of chromite reduction (1995-96)

    Energy Technology Data Exchange (ETDEWEB)

    Xiao Yamping; Holappa, L. [Helsinki Univ. of Technology, Otaniemi (Finland). Lab. of Metallurgy

    1996-12-31

    This article summaries the research work on thermodynamics of chromium slags and kinetic modelling of chromite reduction. The thermodynamic properties of FeCr slag systems were calculated with the regular solution model. The effects of CaO/MgO ratio, Al{sub 2}0{sub 3} amount as well as the slag basicity on the activities of chromium oxides and the oxidation state of chromium were examined. The calculated results were compared to the experimental data in the literature. In the kinetic modelling of the chromite reduction, the reduction possibilities and tendencies of the chromite constitutes with CO were analysed based on the thermodynamic calculation. Two reaction models, a structural grain model and a multi-layers reaction model, were constructed and applied to simulate the chromite pellet reduction and chromite lumpy ore reduction, respectively. The calculated reduction rates were compared with the experimental measurements and the reaction mechanisms were discussed. (orig.) SULA 2 Research Programme; 4 refs.

  1. Innovative soil treatment process design for removal of trivalent chromium

    Energy Technology Data Exchange (ETDEWEB)

    Stallings, J.H. [Air Force, Wright-Patterson AFB, OH (United States). Aeronautical Systems Center; Durkin, M.E. [Hughes Missile Systems Co., Tucson, AZ (United States)

    1997-12-31

    A soil treatment process has been developed as part of a US Air Force environmental compliance project at Air Force Plant 44, Tucson, AZ for treating soil contaminated with heavy metals including trivalent chromium, cadmium, copper, and nickel. The process was designed to treat a total of 133,000 tons of soil in a 400 ton per day facility. Features of the soil treatment process include physical treatment and separation, and a chemical treatment process of the remaining fines using a hypochlorite leach allowing chromium to be solubilized at a high pH. After treating, fines are washed in three stage countercurrent thickeners and chromium hydroxide cake is recovered as a final produce from the leach solution. Treatability studies were conducted, laboratory and a pilot plant was built. Process design criteria and flow sheet, material balances, as well as preliminary equipment selection and sizing for the facility have been completed. Facility was designed for the removal of Cr at a concentration of an average of 1230 mg/kg from the soil and meeting a risk based clean-closure limit of 400 mg/kg of Cr. Capital costs for the 400 tpd plant were estimated at 9.6 million with an operating and maintenance cost of $54 per ton As process is most economic for large quantities of soil with relatively low concentrations of contaminants, it was not used in final closure when the estimated volume of contaminated soil removed dropped to 65,000 tons and concentration of chromium increased up to 4000 mg/kg. However, the process could have application in situations where economics and location warrant.

  2. Tissues and urinary chromium concentrations in rats fed high-chromium diets

    International Nuclear Information System (INIS)

    Complete text of publication follows. Chromium is an essential trace elements and enhances the function of insulin as a form of chromodulin. In the subjects with a certain type of diabetics, 200 to 1,000 μg/d of chromium is administered to reduced the symptoms of diabetics. However, although there are not any health-promotive effects of chromium-administration in healthy subjects, various types of chromium supplements are commercially available in many countries; the adverse effects caused by an excessive chromium intake are feared. In the present study, to clarify the tolerable upper limit of chromium, tissue and urinary chromium concentrations, liver function and iron status were examined in rats fed high-chromium diets. Thirty-six male 4-weeks Wistar rats were divided into six groups and fed casein-based diets containing 1, 10 or 100 μg/g of chromium as chromium chloride (CrCl3) or chromium picolinate (CrPic) for 4 weeks. After the feeding, chromium concentrations in liver, kidney, small intestine and tibia were determined by inductively coupled plasma-mass spectrometry. In addition, urine samples were collected on 3rd to 4th week and their chromium concentrations were also determined. Chromium concentrations in liver, kidney, small intestine and tibia were elevated with increase of dietary chromium concentration. Urinary chromium excretion was also elevated with the increase of dietary chromium and the rate of urinary chromium excretion was less than 2% to dietary chromium intake in all the experimental groups. In the administration of 100 μg/g of chromium, rats given CrCl3 showed significantly higher tibia chromium concentration and lower urinary chromium excretion than those given CrPic. There were not any differences in iron status among the experimental groups. Activities of serum aspartate aminotransferase and alanine aminotransferase in rats fed diet containing 100 μg/g of chromium as CrPic were significantly higher than those in rats fed other diets.

  3. Reductive activation with cysteine represents a chromium(III)-dependent pathway in the induction of genotoxicity by carcinogenic chromium(VI).

    Science.gov (United States)

    Zhitkovich, Anatoly; Quievryn, George; Messer, Joseph; Motylevich, Zhanna

    2002-10-01

    Induction of DNA damage by carcinogenic hexavalent chromium compounds [Cr(VI)] results from its reduction to lower oxidation states. Reductive metabolism of Cr(VI) generates intermediate Cr(V/IV)species, organic radicals, and finally Cr(III), which forms stable complexes with many biological ligands, including DNA. To determine the biological significance of different reaction products, we examined genotoxic responses and the formation of DNA damage during reduction of Cr(VI) by its biological reducer, cysteine. We have found that cysteine-dependent activation of Cr(VI) led to the formation of Cr-DNA and cysteine-Cr-DNA adducts as well as interstrand DNA cross-links. The yield of binary and ternary DNA adducts was relatively constant at different concentrations of Cr(VI) and averaged approximately 54 and 45%, respectively. Interstrand DNA cross-links accounted on average for 1% of adducts, and their yield was even less significant at low Cr(VI) concentrations. Reduction of Cr(VI) in several commonly used buffers did not induce detectable damage to the sugar-phosphate backbone of DNA. Replication of Cr(VI)-modified plasmids in intact human fibroblasts has shown that cysteine-dependent metabolism of Cr(VI) resulted in the formation of mutagenic and replication-blocking DNA lesions. Selective elimination of Cr-DNA adducts from Cr(VI)-treated plasmids abolished all genotoxic responses, indicating that nonoxidative, Cr(III)-dependent reactions were responsible for the induction of both mutagenicity and replication blockage by Cr(VI). The demonstration of the mutagenic potential of Cr-DNA adducts suggests that these lesions can be explored in the development of specific and mechanistically important biomarkers of exposure to toxic forms of Cr.

  4. A mathematical model for the iron/chromium redox battery

    Science.gov (United States)

    Fedkiw, P. S.; Watts, R. W.

    1984-01-01

    A mathematical model has been developed to describe the isothermal operation of a single anode-separator-cathode unit cell in a redox-flow battery and has been applied to the NASA iron/chromium system. The model, based on porous electrode theory, incorporates redox kinetics, mass transfer, and ohmic effects as well as the parasitic hydrogen reaction which occurs in the chromium electrode. A numerical parameter study was carried out to predict cell performance to aid in the rational design, scale-up, and operation of the flow battery. The calculations demonstrate: (1) an optimum electrode thickness and electrolyte flow rate exist; (2) the amount of hydrogen evolved and, hence, cycle faradaic efficiency, can be affected by cell geometry, flow rate, and charging procedure; (3) countercurrent flow results in enhanced cell performance over cocurrent flow; and (4) elevated temperature operation enhances cell performance.

  5. Soils contaminated with hexavalent chromium

    OpenAIRE

    Fonseca, Bruna Catarina da Silva

    2011-01-01

    Tese de doutoramento em Engenharia Química e Biológica The interest in environmental soil science has been growing in the last years due to the continuous degradation of this major natural resource. With this in mind, and because chromium and lead are two of the most toxic heavy metals frequently detected as soil contaminants in the Portuguese territory, the study and development of few remediation techniques and the indissociable description of the sorption and migration of...

  6. Simultaneous determination of chromium(III) and chromium(VI) in aqueous solutions by ion chromatography and chemiluminescence detection

    DEFF Research Database (Denmark)

    Gammelgaard, Bente; Jøns, O; Nielsen, B

    1992-01-01

    A method for the simultaneous determination of chromium(iii) and chromium(vi) in a flow system based on chemiluminescence was developed. A Dionex cation-exchange guard column was used to separate chromium(iii) from chromium(vi), and chromium(vi) was reduced by potassium sulfite, whereupon both sp...

  7. Inoculation of chromium white cast iron

    Directory of Open Access Journals (Sweden)

    D. Kopyciński

    2009-01-01

    Full Text Available It has been proved that an addition of boron carbide introduced as an inoculant to the chromium white cast iron changes the structureof castings. Castings after inoculation revealed a different structure with numerous grains. Primary precipitates of chromium carbide also appeared, reducing the mechanical properties of as-cast parts. Properly established heat treatment regime makes chromium iron castings regain their, originally high, mechanical properties.

  8. REMOVAL OF HEXAVALENT CHROMIUM FROM DRINKING WATER

    OpenAIRE

    A. R. Asgari ، F. Vaezi ، S. Nasseri ، O. Dördelmann ، A. H. Mahvi ، E. Dehghani Fard

    2008-01-01

    Removal of chromium can be accomplished by various methods but none of them is cost-effective in meeting drinking water standards. For this study, granular ferric hydroxide was used as adsorbent for removal of hexavalent chromium. Besides, the effects of changing contact time, pH and concentrations of competitive anions were determined for different amounts of granular ferric hydroxide. It was found that granular ferric hydroxide has a high capacity for adsorption of hexavalent chromium from ...

  9. Hexavalent chromium and lung cancer in the chromate industry: a quantitative risk assessment.

    Science.gov (United States)

    Park, Robert M; Bena, James F; Stayner, Leslie T; Smith, Randall J; Gibb, Herman J; Lees, Peter S J

    2004-10-01

    The purpose of this investigation was to estimate excess lifetime risk of lung cancer death resulting from occupational exposure to hexavalent-chromium-containing dusts and mists. The mortality experience in a previously studied cohort of 2,357 chromate chemical production workers with 122 lung cancer deaths was analyzed with Poisson regression methods. Extensive records of air samples evaluated for water-soluble total hexavalent chromium were available for the entire employment history of this cohort. Six different models of exposure-response for hexavalent chromium were evaluated by comparing deviances and inspection of cubic splines. Smoking (pack-years) imputed from cigarette use at hire was included in the model. Lifetime risks of lung cancer death from exposure to hexavalent chromium (assuming up to 45 years of exposure) were estimated using an actuarial calculation that accounts for competing causes of death. A linear relative rate model gave a good and readily interpretable fit to the data. The estimated rate ratio for 1 mg/m3-yr of cumulative exposure to hexavalent chromium (as CrO3), with a lag of five years, was RR=2.44 (95% CI=1.54-3.83). The excess lifetime risk of lung cancer death from exposure to hexavalent chromium at the current OSHA permissible exposure limit (PEL) (0.10 mg/m3) was estimated to be 255 per 1,000 (95% CI: 109-416). This estimate is comparable to previous estimates by U.S. EPA, California EPA, and OSHA using different occupational data. Our analysis predicts that current occupational standards for hexavalent chromium permit a lifetime excess risk of dying of lung cancer that exceeds 1 in 10, which is consistent with previous risk assessments. PMID:15563281

  10. In situ Carica papaya stem matrix and Fusarium oxysporum (NCBT-156) mediated bioremediation of chromium.

    Science.gov (United States)

    Amatussalam, A; Abubacker, M N; Rajendran, R Babu

    2011-12-01

    Removal of heavy metal chromium was carried out using the fungus Fusarium oxysporum NCBT-156 strain isolated from soil of leather tanning effluent in in situ condition using potassium dichromate solution with 10 per cent Czapek-dox liquid medium. Biosorbent matrix was developed using Carica papaya plant dry stem to colonize the fungal strain to facilitate bioabsorption process. Bioabsorption of chromium was by metabolically mediated intracellular accumulation process. Maximum efficiency of chromium removal by biosorption upto 90 per cent was achieved at the end of 5th day of incubation (120 h of contact time) for 100 and 200 ppm concentration, upto 80 per cent for 300 and 400 ppm, and upto 65 per cent for 500 ppm to 1000 ppm concentrations with pH ranging from 5.8, 5.6, 5.5, 5.4 and 5.2, respectively for 100, 200, 300, 400, 500-1000 ppm concentration. SDS-PAGE protein profile showed significant difference in 34 kDa protein band after chromium absorption by the fungus. FTIR spectroscopic analysis revealed that the main functional groups involved in the uptake of chromium by F. oxysporium strain were carbonyl, carboxyl, amino and hydroxyl groups. PMID:22403866

  11. Permeation of chromium salts through human skin in vitro

    DEFF Research Database (Denmark)

    Gammelgaard, Bente; Fullerton, A; Avnstorp, C;

    1992-01-01

    of the dichromate solution. Chromium skin levels increased with increasing concentrations of applied chromium salts up to 0.034 M Cr. The amount of chromium in recipient phase and skin layers increased with increasing pH when the applied solution contained potassium dichromate. This was ascribed to a decreased skin...... barrier function of the skin. The amount of chromium found in all skin layers after application of chromium chloride decreased with increasing pH due to lower solubility of the salt. The % of chromium found in the recipient phase as chromium(VI) increased with increasing total chromium concentration...... indicating a limited reduction ability of the skin in vitro....

  12. Solution-phase synthesis of chromium-functionalized single-walled carbon nanotubes

    KAUST Repository

    Kalinina, Irina V.

    2015-03-01

    The solution phase reactions of single-walled carbon nanotubes (SWNTs) with Cr(CO)6 and benzene-Cr(CO)3 can lead to the formation of small chromium clusters. The cluster size can be varied from less than 1 nm to about 4 nm by increasing the reaction time. TEM images suggest that the clusters are deposited predominantly on the exterior walls of the nanotubes. TGA analysis was used to obtain the Cr content and carbon to chromium ratio in the Cr-complexed SWNTs. It is suggested that the carbon nanotube benzenoid structure templates the condensation of chromium atoms and facilitates the loss of carbon monoxide leading to well defined metal clusters.

  13. Electrodeposition of chromium from trivalent chromium urea bath containing sulfate and chloride

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    The reduction of Cr( Ⅲ) to Cr( Ⅱ ) on copper electrode in trivalent chromium urea bath containing chromium sulfate and chromium chloride as chromium source has been investigated by potentiodynamic sweep. The transfer coefficient α for reduction of Cr( Ⅲ ) to Cr( Ⅱ ) on copper electrode was calculated as 0.46. The reduction is a quasi-reversible process. J-t responses at different potential steps showed that the generation and adsorption characteristics of carboxylate bridged oligomer are relevant to cathode potential. The interface behavior between electrode and solution for Cr( Ⅲ ) complex is a critical factor influencing sustained electrode position of chromium. The hypotheses of the electro-inducing polymerization of Cr( Ⅲ ) was proposed. The potential scope in which sustained chromium deposits can be prepared is from- 1.3 V to- 1.7 V (vs SCE) in the urea bath. Bright chromium deposits with thickness of 30 μm can be prepared in the bath.

  14. Alkane dehydrogenation over supported chromium oxide catalysts

    NARCIS (Netherlands)

    Weckhuysen, B.M.; Schoonheydt, R.A.

    1999-01-01

    The dehydrogenation of alkanes over supported chromium oxide catalysts in the absence of oxygen is of high interest for the industrial production of propene and isobutene. In this review, a critical overview is given of the current knowledge nowadays available about chromium-based dehydrogenation ca

  15. Tidal asteroseismology: Kepler's KOI-54

    OpenAIRE

    Burkart, Joshua; Quataert, Eliot; Arras, Phil; Weinberg, Nevin N.

    2011-01-01

    We develop a general framework for interpreting and analyzing high-precision lightcurves from eccentric stellar binaries. Although our methods are general, we focus on the recently discovered Kepler system KOI-54, a face-on binary of two A stars with $e=0.83$ and an orbital period of 42 days. KOI-54 exhibits strong ellipsoidal variability during its periastron passage; its lightcurve also contains ~20 pulsations at perfect harmonics of the orbital frequency, and another ~10 nonharmonic pulsat...

  16. Avaliação da resistência da pele de tilápia do Nilo (Oreochrmis niloticus nos sentidos longitudinal, transversal e diagonal, depois de submetida ao curtimento com sais de cromo e recurtimento com agentes - DOI: 10.4025/actascianimsci.v28i3.54 Evaluation of resistance of the Nile tilapia (Oreochromis niloticus skin in longitudinal, transversal and diagonal position after tanning with chromium salts and retanning with different tanning substances - DOI: 10.4025/actascianimsci.v28i3.54

    Directory of Open Access Journals (Sweden)

    Karla Fabrícia de Oliveira

    2006-01-01

    Full Text Available O objetivo do trabalho foi avaliar a resistência da pele da Tilápia do Nilo (Oreochromis niloticus no sentido longitudinal, transversal e diagonal, depois de curtida com sais de cromo e recurtida por diferentes técnicas de recurtimento. As peles foram distribuídas em delineamento inteiramente casualizado, em fatorial 3x3, sendo 3 técnicas de recurtimento (T1 = com 4% de sais de cromo; T2 = 6% com taninos vegetais e T3 = com 6% de taninos sintéticos e 3 posições de retirada dos corpos-de-prova (P1 = longitudinal; P2 = transversal e P3 = diagonal, com 6 repetições por tratamento, em triplicata. O couro foi considerado a unidade experimental. Para os testes de determinação da resistência à tração, ao alongamento e ao rasgamento progressivo, foi utilizado o dinamômetro EMIC. A espessura dos couros variou de 1,00 a 1,20 mm, não diferindo entre as técnicas de recurtimento. Não houve diferença significativa para tração quanto às técnicas de recurtimento, porém, quanto à posição de retirada dos corpos-de-prova, foi significativamente maior para transversal (11,92 N/mm2. A técnica de recurtimento e a posição não influenciaram no rasgamento progressivo (variou de 24,47 a 29,12 N/mm. O couro na posição transversal apresentou maior alongamento independentemente da técnica aplicada, não diferindo apenas na técnica T2 para a posição longitudinal. A pele recurtida com sais de cromo e no sentido transversal apresentou maior resistência à tração e ao alongamento. O recurtimento e a posição não interferiram no rasgamento progressivo.The objective of this experiment was to evaluate the resistance of the Nile tilapia (Oreochromis niloticus skin in longitudinal, transversal and diagonal sections after tanning with chromium salts and re-tanning with different tanning substances. Skins were distributed in a totally randomized design, 3 by 3, with three re-tanning techniques (T1 = with 4% chromium salts; T2 = 6% vegetal

  17. Electron microscopic study on pyrolysis of CCA (chromium, copper and arsenic oxide)-treated wood

    NARCIS (Netherlands)

    Hata, T.; Bronsveld, P.M; Vystavel, T.; Kooi, B.J.; de Hosson, J.T.M.; Kakitani, T.; Otono, A.; Imamura, Y.

    2003-01-01

    The effectiveness of pyrolysis as a possible technique for disposing of CCA (chromium, copper and arsenic oxide)-treated wood was studied. A CCA-treated sample given an extra heat treatment at 450 degreesC for 10 min was thoroughly investigated in order to establish the details of the reaction in wh

  18. High temperature oxidation of iron-chromium alloys

    Energy Technology Data Exchange (ETDEWEB)

    Mikkelsen, Lars

    2003-06-15

    The high temperature oxidation of the ferritic alloy Fe78Cr22 has been investigated in the present work. The effect of small alloying additions of cerium and/or silicon was also investigated. The alloys were oxidized at 973, 1173 and 1373 K in either air or a hydrogen/argon mixture. The various reaction atmospheres contained between 0.02 and 50% water vapour. The oxide scales formed on the various alloys at 973 K consisted of thin chromia layers. The oxide scales grown on the alloys at 1173 K also consisted of a chromia layer. The microstructure of the chromia scales was found to depend on the reaction atmosphere. The chromia scales grown in hydrogen/argon atmospheres formed oxide whiskers and oxide ridges at the surface of the scales, while the chromia scales grown in air formed larger oxide grains near the surface. This difference in oxide microstructure was due to the vaporization of chromium species from the chromia scales grown in air. Two different growth mechanisms are proposed for the growth of oxide whiskers. The growth rate of the chromia scales was independent of the oxygen activity. This is explained by a growth mechanism of the chromia scales, where the growth is governed by the diffusion of interstitial chromium. The addition of silicon to the iron-chromium alloy resulted in the formation of silica particles beneath the chromia scale. The presence of silicon in the alloy was found to decrease the growth rate of the chromia scale. This is explained by a blocking mechanism, where the silica particles beneath the chromia scale partly block the outwards diffusion of chromium from the alloy to the chromia scale. The addition of cerium to the iron-chromium alloy improved the adhesion of the chromia scale to the alloy and decreased the growth rate of chromia. It was observed that the minimum concentration of cerium in the alloy should be 0.3 at.% in order to observe an effect of the cerium addition. The effect of cerium is explained by the &apos

  19. [Bioremediation of chromium (VI) contaminated site by reduction and microbial stabilization of chromium].

    Science.gov (United States)

    Zheng, Jia-Chuan; Zhang, Jian-Rong; Liu, Xi-Wen; Xu, Qian; Shi, Wei-Lin

    2014-10-01

    Chromium (VI) contaminated soil samples were collected from a chemical plant in Suzhou. Firstly, the reduced soil was prepared by adding reagent (Stone-sulfure reagent) into polluted soil to transfer most chromium (VI) into chromium (III), then a nutrient solution was introduced into the reduced soil, and the stabilized soil was obtained after 60 days culturing. The chromium (VI) content of the three kinds of soil was analyzed. The results showed that the chromium (VI) content in toxicity characteristic leaching liquid (TCLL) dropped by 96. 8% (from 8.26 mg · L(-1) to 0.26 mg · L(-1)), and the total chromium content dropped by 95.7% (from 14.66 mg · L(-1) to 0.63 mg · L(-1)) after bioremediation in 5% nutrient solution. Additionally, the durability of chromium stabilization was tested by potassium permanganate oxidation and sterilization of microbe-treated soil. After oxidation, the chromium (VI) content in TCLL of the reduced soil was increased from 8.26 mg · L(-1) to 14.68 mg · L(-1). However, the content after bioremediation was decreased to 2.68 mg · L(-1). The results of sterilization demonstrated that the death of microbe had no significant effect on the stabilization of chromium. Consequently, the research in this paper demonstrated the feasibility of bioremediation of chromium (VI) polluted soil through reduction followed by stabilization/soilidification, and provided a technique with low cost but high efficiency.

  20. Low-chromium reduced-activation chromium-tungsten steels

    Energy Technology Data Exchange (ETDEWEB)

    Klueh, R.L.; Alexander, D.J.; Maziasz, P.J. [Oak Ridge National Lab., TN (United States)

    1996-10-01

    Bainitic microstructures formed during continuous cooling can differ from classical upper and lower bainite formed during isothermal transformation. Two types of non-classical bainite were observed depending on the cooling rate: carbide-free acicular bainite at rapid cooling rates and granular bainite at slower cooling rates. The Charpy impact toughness of the acicular ferrite was found to be considerably better than for the granular bainite. It was postulated that alloying to improve the hardenability of the steel would promote the formation of acicular bainite, just as increasing the cooling rate does. To test this, chromium and tungsten were added to the 2 1/4Cr-2W and 2 1/4Cr-2WV steel compositions to increase their hardenability, and the microstructures and mechanical properties were examined.

  1. Bainitic chromium-tungsten steels with 3 pct chromium

    International Nuclear Information System (INIS)

    Previous work on 3Cr-1.5MoV (nominally Fe-3Cr-2.5Mo-0.25V-0.1C), 2.25Cr-2W (Fe-2.25Cr-2W-0.1C), and 2.25Cr-2WV (Fe-2.25Cr-2W-0.25V-0.1C) steels indicated that the impact toughness of these steels depended on the microstructure of the bainite formed during continuous cooling from the austenization temperature. Microstructures formed during continuous cooling can differ from classical upper and lower bainite formed during isothermal transformation. Two types of nonclassical microstructures were observed depending on the cooling rate: carbide-free acicular bainite at rapid cooling rates and granular bainite at slower cooling rates. The Charpy impact toughness of the acicular ferrite was considerably better than for the granular bainite. It was postulated that alloying to improve the hardenability of the steel would promote the formation of acicular bainite, just as increasing the cooling rate does. To test this, chromium and tungsten were added to the 2.25Cr-2W and 2.25Cr-2WV steel compositions to increase their hardenability. Charpy testing indicated that the new 3Cr-W and 3Cr-WV steels had improved impact toughness, as demonstrated by lower ductile-brittle transition temperatures and higher upper-shelf energies. This improvement occurred with less tempering than was necessary to achieve similar toughness for the 2.25Cr steels and for high-chromium (9 to 12 pct Cr) Cr-W and Cr-Mo steels

  2. Chromium

    Science.gov (United States)

    ... 6+), a toxic form that results from industrial pollution. This fact sheet focuses exclusively on trivalent (3+) ... 1 medium 1 Banana, 1 medium 1 Green beans, ½ cup 1 What are recommended intakes of ...

  3. Reproductive toxicological aspects of chromium in males

    International Nuclear Information System (INIS)

    To expand our present understanding of the effects of chromium on male fertility a number of studies were designed to achieve this through the use of chromium intoxicated experimental animals and through investigation of sexual hormones and sperm quality in welders. Also in view of the lack of an experimental model for effects of noxious substance on the epididymal spermatozoa the main objectives of the series of studies reviewed here were: A. To establish a model for evaluation of epididymal sperm count and motility in the rat. B. To investigate and compare the effects of tri- and hexavalent chromium on epididymal spermatozoa. Further to describe the effects of low-dose long-time exposure of rats to the most toxicological interesting chromium oxidative state - hexavalent chromium. C. By the use of autoradiography and γ-countinuing to expand the present knowledge on the distribution of chromium in the body with special reference to the male reproductive organs. D. To describe the effects of exposure to hexavalent chromium in welding fume on levels of sexual hormones and semen parameters in welders. (EG)

  4. Chromium(VI) reduction by ascorbate: role of reactive intermediates in DNA damage in vitro.

    OpenAIRE

    Stearns, D M; Courtney, K D; Giangrande, P H; Phieffer, L S; Wetterhahn, K E

    1994-01-01

    Reaction of chromium(VI) with one equivalent of ascorbate was studied by electron paramagnetic resonance spectroscopy in the presence of 0.10 M 5,5-dimethyl-1-pyrroline-1-oxide (DMPO) at room temperature in 0.10 M (N-[2-hydroxyethyl]piperazine-N'-[2-ethanesulfonic acid]) (HEPES) and 0.05 M tris(hydroxymethyl)aminomethane hydrochloride (Tris-HCl) buffers (pH 7.0 room temperature). Chromium(V), ascorbyl radical, and carbon-based DMPO-radical adducts were observed. A higher level of Cr(V) was ob...

  5. Synthesis of Chromium (Ⅲ) 5-aminosalicylate

    Institute of Scientific and Technical Information of China (English)

    LI Wei; HAO Er-jun; JIANG Yu-qin

    2004-01-01

    As we all known that diabetes is a chronic disease with major health consequences.Research has revealed that the occurrence of diabetes have great thing to do with the chromium deficient. Almost 40 years after the first report of glucose tolerance factor(GTF) [1], no conclusive evidence for an isolable ,biologically active form of chromium exited. Three materials have been proposed to be the biologically active form of chromium: "glucose tolerance factor", chromium Picolinate and low-molecular-weight chromium-binding substance (LWMCr) [2] . So there is potential for the design of new chromium drugs .5-Aminosalicylic acid (5-ASA) is identified as an active component in the therapy of inflammatory bowel disease (IBD) such as Crohn's disease and ulcerative colitis . The therapeutic action of 5-ASA is believed to be coupled to its ability to act as a free radical scavenger [3-4],acting locally on the inflamed colonic mucosa [5-7]. However, the clinical use of 5-ASA is limited, since orally administered 5-ASA is rapidly and completely absorbed from the upper gastrointestinal tract and therefore the local therapeutic effects of 5-ASA in the colon is hardly expected.In this paper, we report the synthesis of chromium(Ⅲ)5-aminosalicylate from 5-ASA and CrCl3. 6H2O.The synthesis route is as follow:The complex has been characterized by elemental analysis, IR spectra, X-ray powder diffractionand TG-DTA . They indicate that the structure is tris(5-ASA) Chromium . Experiments show that thecomplex has a good activity for supplement tiny dietary chromium, lowering blood glucose levels,lowering serum lipid levels and in creasing lean body mass .

  6. Wet skins tanning with chromium in dense CO2 under pressure

    International Nuclear Information System (INIS)

    An ancestral gesture steadily improved through the centuries, the transformation of skins into leather includes several stages of which the principal one is tanning. Today, 90 % of the world's leather products are tanned with chromium. However, this stage is an environmental liability, and reducing the volume and chromium content of the waste has become a major issue. A first study on skin degreasing by dense CO2 helped sharply reduce the volume of the fatty effluents. To replace water by dense CO2 as the tanning medium was the logical next step. The present study was carried out in cooperation with three tanneries in the Rhone-Alpes-Auvergne area of France and a manufacturer of tanning materials. The difficulty of the study was the chemically opposed character of the two media involved. CO2 is a non-polar and lipophilic solvent while inorganic chromium is insoluble. The water present in the treated skin is a polar and ionic reaction medium and one of the reagents in tanning chemistry. The mixture of these two partially miscible compounds gives a pH 3 by carbonic acid formation. Tanning is based on the reactivity of collagen, the main component of the skin, with hydroxylated complexes of chromium. Collagen is a protein containing some chemical functions, amines (R-NH2) and carboxylic (R-COOH) for example. These functions impart an amphoteric character to the compound. The WERNER theory of complex salts explains the formation of hydroxylated complexes of chromium and their fixing on the carboxylic functions of collagen by oxolation. pH is the key parameter in tanning. The success of the process demands chromium impregnation without fixing it at a pH lower than 5, and then to fix it by increasing the pH. This opened two alternatives for transferring chromium in the skin: solubilize chromium in CO2 via soluble organometallic complexes; or put the chromium salt into suspension without solubilizing it. The best results were obtained with the second option, which is

  7. Genesis and transport of hexavalent chromium in the system ophiolitic rocks - groundwater

    Science.gov (United States)

    Shchegolikhina, Anastasia; Guadagnini, Laura; Guadagnini, Alberto

    2015-04-01

    Our study aims at contributing to the quantification and characterization of chromium transport processes from host rocks and soil matrices to groundwater. We focus on dissolved hexavalent chromium detected in groundwaters of geological regions with ophiolitic rocks (ophiolites and serpentinites) inclusions due to its critical ecological impact. (Oze et al., 2004). Despite the large number of analyses on the occurrence of high concentrations of hazardous hexavalent chromium ions in natural waters, only few studies were performed with the objective of identifying and investigating the geochemical reactions which could occur in the natural system rock - groundwater - dissolved chromium (Fantoni et al., 2002, Stephen and James, 2004, Lelli et al., 2013). In this context, there is a need for integration of results obtained from diverse studies in various regions and settings to improve our knowledge repository. Our theoretical analyses are grounded and driven by practical scenarios detected in subsurface reservoirs exploited for civil and industrial use located in the Emilia-Romagna region (Italy). Available experimental datasets are complemented with data from other international regional-scale settings (Altay mountains region, Russia). Modeling of chromium transformation and migration particularly includes characterization of the multispecies geochemical system. A key aspect of our study is the analysis of the complex competitive sorption processes governing heavy metal evolution in groundwater. The results of the research allow assessing the critical qualitative features of the mechanisms of hexavalent chromium ion mobilization from host rocks and soils and the ensuing transformation and migration to groundwater under the influence of diverse environmental factors. The study is then complemented by the quantification of the main sources of uncertainty associated with prediction of heavy metal contamination levels in the groundwater system explored. Fantoni, D

  8. Chromium in leather footwear-risk assessment of chromium allergy and dermatitis

    DEFF Research Database (Denmark)

    Thyssen, Jacob P; Strandesen, Maria; Poulsen, Pia B;

    2012-01-01

    Background. Chromium-tanned leather footwear, which releases >3 ppm hexavalent Cr(VI), may pose a risk of sensitizing and eliciting allergic dermatitis. Objectives. To determine the content and potential release of chromium in leather footwear and to discuss the prevention of chromium contact...... allergy and dermatitis. Methods. Sixty pairs of leather shoes, sandals and boots (20 children's, 20 men's, and 20 women's) were purchased in Copenhagen and examined with X-ray fluorescence spectroscopy. Chromium was extracted according to the International Standard, ISO 17075. The detection level for Cr......(VI) was 3 ppm. Results. Chromium was identified in 95% of leather footwear products, the median content being 1.7% (range 0-3.3%). No association with store category or footwear category was found. A tendency for there to be a higher chromium content in footwear with high prices was shown (p(trend) = 0...

  9. 5-(4-氯苯基偶氮)-8-苯基磺酰氨基喹啉与铜(Ⅱ)的荧光反应及分 析应用研究%Study on the Fluorescence Reaction of Copper(Ⅱ) with 5 -(4-Chlorophenylazo)-8-Benzenesultonamidoquinoline and Its Analytical Appl ications

    Institute of Scientific and Technical Information of China (English)

    叶艳青; 曹秋娥; 徐其亨

    2001-01-01

    A fluorescence reaction of copper(Ⅱ) with 5-(4-chlorophenylazo)-8-benzenesu ltona-midoquinoline (CPBSQ) was firstly studied.CPBSQ could react with Cu(Ⅱ) in the medium of Na2B4O7-NaH2PO4 buffer solution (pH=7.5) to form a1 ∶2 complex,which showed an intensive fluorescence at λex/λ em=327nm/368nm.Based on this fluorescence reaction,a sensitive and selective f luorescent method for the determination of Cu(Ⅱ) was developed.The linearity ra nge of this method is over 0.10—50μg/L with a detection limit of 1.06ng/L. The method has been successfully used to the determination of copper in waste water,hair and food samples.%研究了一种新试剂:5-(4-氯苯基偶氮)-8-苯基磺酰氨基喹啉(CPBSQ)在聚乙烯醇存在下与铜(Ⅱ)的荧光反应。结果表明,在pH=7.5的硼砂-磷酸二氢钠缓冲溶液中,铜(Ⅱ)与CPBSQ 形成1∶2的稳定配合物,在λex/λem=327nm/368nm产生强荧光。依 此建立一种高灵敏和选择性的荧光分析方法,该法能检测0.10—50μg/L Cu(Ⅱ),其检 出限为1.06ng/L。用此法测定了废水、人发和食品中铜的含量,结果令人满意。

  10. Selective and sensitive detection of chromium(VI) in waters using electrospray ionization mass spectrometry.

    Science.gov (United States)

    Weldy, Effie; Wolff, Chloe; Miao, Zhixin; Chen, Hao

    2013-09-01

    From 2000 through 2011, there were 14 criminal cases of violations of the Clean Water Act involving the discharge of chromium, a toxic heavy metal, into drinking and surface water sources. As chromium(VI), a potential carcinogen present in the environment, represents a significant safety concern, it is currently the subject of an EPA health risk assessment. Therefore, sensitive and selective detection of this species is highly desired. This study reports the analysis of chromium(VI) in water samples by electrospray ionization mass spectrometry (ESI-MS) following its reduction and complexation with ammonium pyrrolidinedithiocarbamate (APDC). The reduction and subsequent complexation produce a characteristic [Cr(III)O]-PDC complex which can be detected as a protonated ion of m/z 507 in the positive ion mode. The detection is selective to chromium(VI) under acidic pH, even in the presence of chromium(III) and other metal ions, providing high specificity. Different water samples were examined, including deionized, tap, and river waters, and sensitive detection was achieved. In the case of deionized water, quantification over the concentration range of 3.7 to 148ppb gave an excellent correlation coefficient of 0.9904 using the enhanced MS mode scan. Using the single-reaction monitoring (SRM) mode (monitoring the characteristic fragmentation of m/z 507 to m/z 360), the limit of detection (LOD) was found to be 0.25ppb. The LOD of chromium(VI) for both tap and river water samples was determined to be 2.0ppb. A preconcentration strategy using simple vacuum evaporation of the aqueous sample was shown to further improve the ESI signal by 15 fold. This method, with high sensitivity and selectivity, should provide a timely solution for the real-world analysis of toxic chromium(VI).

  11. Surface Microstructure and Component Changes of Chromium-resistant Enterobacter Cloacae CYS-25 Strain

    Institute of Scientific and Technical Information of China (English)

    MA Xiao-Yan; CHENG Yang-Jian; ZHENG Jing; YANG Chun-Peng; LI Bin; LI Dong-Song; LIN Zhang; HUANG Feng

    2008-01-01

    Enterobacter cloacae CYS-25 strain was isolated from a chromate plant. This bacte-rium was capable of resisting high hexavalent chromium concentration and reducing Cr(Ⅵ) under aerobic condition. CrO42- stimulated the increase of bacterial size and production of compact convex paths containing chromium on the bacterial surface. The increase of bacterial size was caused by integrative growth but not extracellular polymeric substance hyperplasia. IR and SDS-PAGE analyses showed the extraeellular polymeric substance (EPS) components were mainly proteins and had no obvious changes whether the strains were induced by Cr(Ⅵ) or not. The EPS was amorphous and contained trivalent chromium. Under CrO42- growth condition, the extracellular substance of Enterobacter cloacae CYS-25 strains and Cr(Ⅵ) had redox reaction. The products were Cr3+-protein complexes which formed a piece of compact convex paths on the surface of bacteria and prevented Cr(Ⅵ) from entering into cells.

  12. Potentiometry: A Chromium (III) -- EDTA Complex

    Science.gov (United States)

    Hoppe, J. I.; Howell, P. J.

    1975-01-01

    Describes an experiment that involves the preparation of a chromium (III)-EDTA compound, a study of its infrared spectrum, and the potentiometric determination of two successive acid dissociation constants. (Author/GS)

  13. Localized Corrosion of Chromium Coated Steel

    NARCIS (Netherlands)

    Zhang, X.; Beentjes, P.; Mol, A.; Terryn, H.

    2006-01-01

    In this paper, we report on the studies of the local corrosion behaviour of chromium-coated ultra low carbon steel in NaCl solution using polarization, electrochemical impedance spectroscopy (EIS) and SVET.

  14. Synthesis, characterization and catalytic activity of chromium substituted cobalt ferrospinels

    International Nuclear Information System (INIS)

    Chromium substituted cobalt ferrospinels were prepared by soft citrate gel method. The synthesized material was characterized by various physico-chemical methods. All the samples showed a single-phase cubic structure. Lattice constant varies from 8.389 to 8.323 A. Transmission electron microscopic study indicated the nanostructure of the catalysts while homogenous grain distribution was presented by scanning electron microscopic studies. The catalytic activity of the samples was investigated towards acetylation of phenols. The presence of active centers on the surface of the material was confirmed through pyridine adsorption studies. The surface acidity of the catalyst is responsible for better catalytic performance. The material was found to serve as a promising catalyst for acylation and benzoylation of phenols under solvent free condition. These catalysts are ∼100% selective towards o-acylation of phenols, a promising reaction for perfumery intermediates. The catalysts were seen to be reusable without any further treatment. Catalytic activities of cobalt, chromium and iron oxides were also investigated for comparison. The cobalt ferrospinel was found to have better catalytic activity as compared to the Cr-substituted ferrospinels and the pure oxides. Cobalt ferrite catalyst offers high yields in a short reaction time under solvent-free conditions.

  15. Synthesis, characterization and catalytic activity of chromium substituted cobalt ferrospinels

    Energy Technology Data Exchange (ETDEWEB)

    Hankare, P.P., E-mail: p_hankarep@rediffmail.com [Department of Chemistry, Shivaji University, Kolhapur, Maharashtra, 416 004 (India); Sankpal, U.B., E-mail: sankpalumesh@gmail.com [Department of Chemistry, Shivaji University, Kolhapur, Maharashtra, 416 004 (India); Patil, R.P. [Department of Chemistry, Shivaji University, Kolhapur, Maharashtra, 416 004 (India); Lokhande, P.D. [Department of Chemistry, University of Pune, Pune, Maharashtra, 411 007 (India); Sasikala, R. [Chemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400 085 (India)

    2011-02-15

    Chromium substituted cobalt ferrospinels were prepared by soft citrate gel method. The synthesized material was characterized by various physico-chemical methods. All the samples showed a single-phase cubic structure. Lattice constant varies from 8.389 to 8.323 A. Transmission electron microscopic study indicated the nanostructure of the catalysts while homogenous grain distribution was presented by scanning electron microscopic studies. The catalytic activity of the samples was investigated towards acetylation of phenols. The presence of active centers on the surface of the material was confirmed through pyridine adsorption studies. The surface acidity of the catalyst is responsible for better catalytic performance. The material was found to serve as a promising catalyst for acylation and benzoylation of phenols under solvent free condition. These catalysts are {approx}100% selective towards o-acylation of phenols, a promising reaction for perfumery intermediates. The catalysts were seen to be reusable without any further treatment. Catalytic activities of cobalt, chromium and iron oxides were also investigated for comparison. The cobalt ferrospinel was found to have better catalytic activity as compared to the Cr-substituted ferrospinels and the pure oxides. Cobalt ferrite catalyst offers high yields in a short reaction time under solvent-free conditions.

  16. Synthesis and Characterization of Chromium Oxide Nanoparticles

    OpenAIRE

    Vivek Sheel Jaswal; Avnish Kumar Arora; Joginder Singh; Mayank Kinger; Vishnu Dev Gupta

    2014-01-01

    Chromium oxide nanoparticles (NPs)have been rapidly synthesized by precipitation method using ammomia as precipitating agent and are characterized by using X-ray Diffraction (XRD), Thermo Gravimetric Analysis (TGA), UV-Visible absorption (UV), Infrared Spectoscopy (IR), Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM). XRD studies show that chromium oxide NP is formed as Cr2O3 and it has hexagonal structure. The shape and particle size of the synthesized Cr2O3 NP...

  17. Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2015-01-01

    Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod

  18. Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, Low-Carbon Nickel-Chromium-Molybdenum-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Tungsten, and Low-Carbon Nickel-Molybdenum-Chromium Alloy Plate, Sheet, and Strip

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2015-01-01

    Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, Low-Carbon Nickel-Chromium-Molybdenum-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Tungsten, and Low-Carbon Nickel-Molybdenum-Chromium Alloy Plate, Sheet, and Strip

  19. Bioremediation of chromium solutions and chromium containing wastewaters.

    Science.gov (United States)

    Malaviya, Piyush; Singh, Asha

    2016-08-01

    Cr(VI) represents a serious threat to human health, living resources and ecological system as it is persistent, carcinogenic and toxic, whereas, Cr(III), another stable oxidation state of Cr, is less toxic and can be readily precipitated out of solution. The conventional methods of Cr(VI) removal from wastewaters comprise of chemical reduction followed by chemical precipitation. However, these methods utilize large amounts of chemicals and generate toxic sludge. This necessitates the need for devising an eco-technological strategy that would use the untapped potential of the biological world for remediation of Cr(VI) containing wastewaters. Among several viable approaches, biotransformation of Cr(VI) to relatively non-toxic Cr(III) by chromium resistant bacteria offers an economical- and environment-friendly option for its detoxification. Various studies on use of Cr(VI) tolerant viable bacterial isolates for treatment of Cr(VI) containing solutions and wastewater have been reported. Therefore, a detailed account of mechanisms and processes involved in bioreduction of Cr(VI) from solutions and wastewaters by bacterial isolates are the focus of this review article in addition to a discussion on toxicity of Cr(VI) on bacterial strains and various factors affecting Cr(VI) bioreduction. PMID:25358056

  20. Kinetics of Voluminal Reduction of Chromium Ore Fines Containing Coal by Microwave Heating

    Institute of Scientific and Technical Information of China (English)

    CHEN Jin; WANG She-bin; ZHANG Meng; LIU Jin-ying; ZHOU Jian-xiong

    2008-01-01

    The kinetics of voluminal reduction of chromium ore fines containing coal(COFCC)by microwave heating was studied.When the molar ratio of carbon to oxygen was 0.84 and that of CaO to SiO2 was 0.39 in COFCC,the temperature-rising rate of COFCC by microwave heating was 62.5℃/min,68.75℃/min,70.59℃/rain,and 72.22℃/min at 1 000℃,1100℃,1200℃,and 1300℃,respectively.The results show that the voluminal reduction of COFCC by microwave heating at solid-solid phase is first order reaction,with the apparent activation energy of 51.480 kJ/mol.The limiting step of reaction rate for the overall reaction is the mass transfer of CO in the reduced product layer between dielectric particles of chromium ore and coal.

  1. Direct access to macroporous chromium nitride and chromium titanium nitride with inverse opal structure.

    Science.gov (United States)

    Zhao, Weitian; DiSalvo, Francis J

    2015-03-21

    We report a facile synthesis of single-phase, nanocrystalline macroporous chromium nitride and chromium titanium nitride with an inverse opal morphology. The material is characterized using XRD, SEM, HR-TEM/STEM, TGA and XPS. Interconversion of macroporous CrN to Cr2O3 and back to CrN while retaining the inverse opal morphology is also demonstrated.

  2. Diminishing Chromium Use on Combined Chromium-Gambier Tanning Process Upon the Characteristics of Tanned Leather

    Directory of Open Access Journals (Sweden)

    A. Kasim

    2014-04-01

    Full Text Available The research was aimed to investigate the influence of minimizing chromium use on combined chromium-gambier process upon the characteristics of tanned leather. At the first stage of tanning process, chromium was used and in the second stage it was replaced by gambier. The raw material used was dried saline-preserved goat skin. The treatments applied on the tanning process were the different concentrations of chromium ranging from the highest level of 6% to the lowest level of 1% which was then re-tanned by using 8% concentration of gambier. The examination parameters included chemical and physical properties as well as visual investigation on the tanned leather in accordance with SNI-06-0463-1989-A. The result showed that the tanning process by using 2% chromium in the first step and 8% gambier in the second step was a treatment combination producing tanned leather that met the standard. The examination on tanned leather resulted from such treatment showed 56.33% rawhide, 17.45% of bound tannin, 31.22% of tanning level, tensile strength 386.30 kg/cm2, flexibility 31.91%, leather width 1.3 mm, density 0.75 g/cm3, the leather was quite elastic with light brownish color. In conclusion, minimizing the use of chromium in the combined tanning process of chromium and gambier can be implemented to the lowest of 2% chromium concentration and 8% gambier in the first and second step, respectively.

  3. Lateral stress evolution in chromium sulfide cermets with varying excess chromium

    Science.gov (United States)

    Petel, O. E.; Appleby-Thomas, G. J.; Wood, D. C.; Capozzi, A.; Nabavi, A.; Goroshin, S.; Frost, D. L.; Hazell, P. J.

    2016-04-01

    The shock response of chromium sulfide-chromium, a cermet of potential interest as a matrix material for ballistic applications, has been investigated at two molar ratios. Using a combustion synthesis technique allowed for control of the molar ratio of the material, which was investigated under near-stoichiometric (cermet) and excess chromium (interpenetrating composite) conditions, representing chromium:sulfur molar ratios of 1.15:1 and 4:1, respectively. The compacts were investigated via the plate-impact technique, which allowed the material to be loaded under a one-dimensional state of strain. Embedded manganin stress gauges were employed to monitor the temporal evolution of longitudinal and lateral components of stress in both materials. Comparison of these two components has allowed assessment of the variation of material shear strength both with impact pressure/strain-rate and time for the two molar ratio conditions. The two materials exhibited identical material strength despite variations in their excess chromium contents.

  4. Nuclear Data Sheets for A = 54

    Energy Technology Data Exchange (ETDEWEB)

    Dong, Yang; Junde, Huo

    2014-09-15

    The 2005 evaluation for A=54 (2006Hu08) has been updated. Detailed experimental nuclear structure data and decay data for all nuclei with mass chain A=54 are presented in this current evaluation. The new data and information are given in following datasets: {sup 54}Ca: {sup 9}Be({sup 76}Ge, X) and Be({sup 55}Sc, p), ({sup 56}Ti, 2p) {sup 54}Sc: {sup 54}Ca β{sup −} decay and {sup 54}Sc IT decay {sup 54}Ti: {sup 54}Sc β{sup −} decay {sup 54}Cr: {sup 54}Mn ε decay, {sup 56}Fe(μ, nupng), and {sup 238}U({sup 64}Ni, Xγ) {sup 54}Mn: {sup 51}V({sup 20}Ne, Xγ), {sup 55}Mn(p, pn), and {sup 56}Fe(μ, nu2ng) {sup 54}Fe: {sup 58}Ni α decay, {sup 9}Be({sup 55}Co, Xγ), {sup 54}Fe(e, e'), {sup 54}Fe(p, p'), and Coulomb Excitation {sup 54}Co: {sup 54}Ni ε decay, {sup 55}Cu εp decay, {sup 28}Si({sup 32}S, αpnγ), {sup 54}Fe(p,n), and {sup 54}Fe({sup 3}He, t) {sup 54}Ni: {sup 54}Ni IT decay, {sup 55}Zn εp decay, {sup 9}Be({sup 55}Ni, Xγ), and {sup 24}Mg({sup 32}S, Xγ) {sup 54}Zn: Ni({sup 58}Ni, X)

  5. Serum chromium levels in gestational diabetes mellitus

    Directory of Open Access Journals (Sweden)

    P G Sundararaman

    2012-01-01

    Full Text Available Objective: To measure serum chromium level in women with gestational diabetes mellitus (GDM from Chennai, South India. Materials and Methods: Thirty women with gestational diabetes, 60 age matched controls. Inclusion criteria: Gestational age 22-28 weeks, age group 20-35 years. Exclusion Criteria: Gestational age beyond 28 weeks, malnutrition or presence of infection. Serum chromium was measured using inductive couple plasma emission spectrometer. Results: Serum chromium levels of women with GDM, 1.59+/-0.02 ng/ml (range: 0.16-4.0 ng/ml were lower than in controls (4.58+/-0.62 ng/ml; range 0.82-5.33 ng/ml (P < 0.001. However, there were no significant differences among cases and controls when subdivided by parity. Conclusions: Women with GDM from a South Indian city had lower levels of serum chromium compared to pregnant women without GDM. Studies may be done whether chromium supplementation is useful in this group of women.

  6. Flashlamp-pumped lasing of chromium-doped GSG garnet

    International Nuclear Information System (INIS)

    The implications for the practical use of chromium:GSGG in lamp-pumped tunable lasers are discussed in this paper. The authors report here some major improvements in the performance of the flashlamp-pumped chromium:GSGG laser

  7. Structural effects of metallic chromium on its electrochemical behavior

    Directory of Open Access Journals (Sweden)

    VELIMIR RADMILOVIC

    2007-06-01

    Full Text Available Chromium dissolution in aqueous sulfuric acid solution of pH 1 was studied electrochemically on chromium electrodes with different crystallographic structures. A slow potentiodynamic method was used for the electrochemical measurements in deaerated solutions (purgedwith nitrogen,while the Cr(III ions in the solution after the corrosion were determined by atomic absorption spectrometry. Three electrode materials with a very dominant crystallite orientation resembling single crystal structures (i.e., 111 and 110 confirmed by the electron backscattering diffraction (EBSD, were used in the experiments. The (111 structures were somewhat more active electrochemically (both anodic and cathodic than the (110 structure. However, Cr electrochemically deposited in standard plating bath, assumed from literature data to has also the (111 structure, was more than 4 times active for anodic dissolution and, by the same number, less active for cathodic hydrogen evolution. The concentrations of Cr(III ions determined in the solution after definite times of corrosion of all the materials showed almost two times larger dissolution rates than observed electrochemically by three different electrochemical methods (Wagner–Traud, Stern–Geary, electrochemical impedance spectroscopy. This is explained by the simultaneous occurrence of potential independent chemical dissolution of Cr, by a direct reaction of metallic Cr with H2O molecules, proposed a long time ago by Kolotyrkin and coworkers.

  8. Determination of chromium combined with DNA, RNA and proteins in chromium-rich brewer's yeast by NAA

    International Nuclear Information System (INIS)

    The content of chromium in the DNA, RNA and protein fractions separated from chromium-rich and normal brewer's yeast was determined by neutron activation analysis (NAA). Our results show that the extracted relative amounts and concentrations of DNA, RNA and proteins have no significant difference for two types of yeast, but the chromium content in DNA, RNA and proteins fractions extracted from the chromium-rich yeast are substantially higher than those from the normal. In addition, the concentration of chromium in DNA is much higher than that in RNA and proteins. It is evident that the inorganic chromium compounds can enter the yeast cell during the yeast cultivation in the chromium-containing culture medium and are converted into organic chromium species, which are combined with DNA, RNA and proteins. (author)

  9. Chromium allergy and dermatitis: prevalence and main findings

    DEFF Research Database (Denmark)

    Bregnbak, David; Johansen, Jeanne D.; Jellesen, Morten Stendahl;

    2015-01-01

    The history of chromium as an allergen goes back more than a century, and includesan interventional success with national legislation that led to significant changes inthe epidemiology of chromium allergy in construction workers. The 2015 EU Leather Regulation once again put a focus on chromium...

  10. Thermodynamic properties of chromium bearing slags and minerals. A review

    Energy Technology Data Exchange (ETDEWEB)

    Xiao Yanping; Holappa, L.

    1996-12-31

    In this report, the thermodynamic properties of chromium bearing slags and minerals were reviewed based on the available information in the literature. It includes the analysing methods for oxidation state of chromium in slags, oxidation state of chromium and activities of chromium oxides in slags and minerals. The phase diagrams of chromium oxide systems and chromium distributions between slag and metal phases are also covered ill this review. Concerning the analysing methods, it was found that most of the available approaches are limited to iron free slag systems and the sample preparation is very sensitive to the analysing results. In silicate slags under reducing atmosphere, divalent and trivalent chromium co-exist in the slags. It is agreed that the fraction of divalent chromium to total chromium increases with higher temperature, lower slag basicity and oxygen potential. For the slags under oxidising atmosphere, trivalent, pentavalent and hexavalent states were reported to be stable. The activities of CrO and CrO{sub 1.5} were concluded to have positive deviation from ideal solution. Slag basicity has a positive effect and temperature has a negative effect on the activities of chromium oxides. The phase diagrams of the Cr-O, binary, and ternary chromium containing oxide systems have been examined systematically. The analysis shows that the data on the quaternary and quinary systems are insufficient, and require further investigation. The most important features of the chromium containing silicate slags are the large miscibility gaps and the stability of the chromite spinel. (orig.) (76 refs.)

  11. 21 CFR 73.1015 - Chromium-cobalt-aluminum oxide.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Chromium-cobalt-aluminum oxide. 73.1015 Section 73... LISTING OF COLOR ADDITIVES EXEMPT FROM CERTIFICATION Drugs § 73.1015 Chromium-cobalt-aluminum oxide. (a) Identity. The color additive chromium-cobalt-aluminum oxide is a blue-green pigment obtained by calcining...

  12. Collisional properties of trapped cold chromium atoms

    CERN Document Server

    Pavlovich, Z; Côté, R; Sadeghpour, H R; Pavlovic, Zoran; Roos, Bjoern O.; Côté, Robin

    2004-01-01

    We report on calculations of the elastic cross section and thermalization rate for collision between two maximally spin-polarized chromium atoms in the cold and ultracold regimes, relevant to buffer-gas and magneto-optical cooling of chromium atoms. We calculate ab initio potential energy curves for Cr2 and the van der Waals coefficient C6, and construct interaction potentials between two colliding Cr atoms. We explore the effect of shape resonances on elastic cross section, and find that they dramatically affect the thermalization rate. Our calculated value for the s-wave scattering length is compared in magnitude with a recent measurement at ultracold temperatures.

  13. Studying chromium biosorption using arabica coffee leaves

    Directory of Open Access Journals (Sweden)

    Luis Carlos Florez García

    2010-05-01

    Full Text Available This work was aimed at providing an alternative for removing heavy metals such as chromium from waste water (effluent from the leather industry and galvanoplasty (coating with a thin layer of metal by electrochemical means, using coffee leaves as bio- mass. Using arabica coffee (Castle variety leaves led to 82% chromium removal efficiency for 1,000 mg/L synthetic dissolutions in 4 pH dissolution operating conditions, 0 rpm agitation, 0.149 mm diameter biomass particle size and 0.85 g/ml biomass / dissolution volume ratio.

  14. Strategies for chromium bioremediation of tannery effluent.

    Science.gov (United States)

    Garg, Satyendra Kumar; Tripathi, Manikant; Srinath, Thiruneelakantan

    2012-01-01

    Bioremediation offers the possibility of using living organisms (bacteria, fungi, algae,or plants), but primarily microorganisms, to degrade or remove environmental contaminants, and transform them into nontoxic or less-toxic forms. The major advantages of bioremediation over conventional physicochemical and biological treatment methods include low cost, good efficiency, minimization of chemicals, reduced quantity of secondary sludge, regeneration of cell biomass, and the possibility of recover-ing pollutant metals. Leather industries, which extensively employ chromium compounds in the tanning process, discharge spent-chromium-laden effluent into nearby water bodies. Worldwide, chromium is known to be one of the most common inorganic contaminants of groundwater at pollutant hazardous sites. Hexavalent chromium poses a health risk to all forms of life. Bioremediation of chromium extant in tannery waste involves different strategies that include biosorption, bioaccumulation,bioreduction, and immobilization of biomaterial(s). Biosorption is a nondirected physiochemical interaction that occurs between metal species and the cellular components of biological species. It is metabolism-dependent when living biomass is employed, and metabolism-independent in dead cell biomass. Dead cell biomass is much more effective than living cell biomass at biosorping heavy metals, including chromium. Bioaccumulation is a metabolically active process in living organisms that works through adsorption, intracellular accumulation, and bioprecipitation mechanisms. In bioreduction processes, microorganisms alter the oxidation/reduction state of toxic metals through direct or indirect biological and chemical process(es).Bioreduction of Cr6+ to Cr3+ not only decreases the chromium toxicity to living organisms, but also helps precipitate chromium at a neutral pH for further physical removal,thus offering promise as a bioremediation strategy. However, biosorption, bioaccumulation, and

  15. Standard Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625), Nickel-Chromium-Molybdenum-Silicon Alloy (UNS N06219), and Nickel-Chromium-Molybdenum-Tungsten Alloy (UNS N06650) Rod and Bar

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2014-01-01

    Standard Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625), Nickel-Chromium-Molybdenum-Silicon Alloy (UNS N06219), and Nickel-Chromium-Molybdenum-Tungsten Alloy (UNS N06650) Rod and Bar

  16. A chromium nitride/carbon nitride containing graphitic carbon nanocapsule hybrid as a Pt-free electrocatalyst for oxygen reduction.

    Science.gov (United States)

    Zhao, Lu; Wang, Lei; Yu, Peng; Zhao, Dongdong; Tian, Chungui; Feng, He; Ma, Jing; Fu, Honggang

    2015-08-11

    Chromium nitride nanoparticles supported on graphitic carbon nanocapsules containing carbon nitride (CrN/GC) have been synthesized by a solvothermal-assisted ion-exchange route. As a Pt-free catalyst, the CrN/GC hybrid exhibits superior activity, stability, methanol immunity and a dominant 4-electron pathway towards oxygen reduction reaction.

  17. Molecular aspects of glucose dehydration by chromium chlorides in ionic liquids.

    Science.gov (United States)

    Zhang, Yanmei; Pidko, Evgeny A; Hensen, Emiel J M

    2011-05-01

    A combined experimental and computational study of the ionic-liquid-mediated dehydration of glucose and fructose by Cr(II) and Cr(III) chlorides has been performed. The ability of chromium to selectively dehydrate glucose to 5-hydroxymethylfurfural (HMF) in the ionic liquid 1-ethyl-3-methyl imidazolium chloride does not depend on the oxidation state of chromium. Nevertheless, Cr(III) exhibits higher activity and selectivity to HMF than Cr(II) . Anhydrous CrCl(2) and CrCl(3)⋅6 H(2)O readily catalyze glucose dehydration with HMF yields of 60 and 72%, respectively, after 3 h. Anhydrous CrCl(3) has a lower activity, because it only slowly dissolves in the reaction mixture. The transformation of glucose to HMF involves the formation of fructose as an intermediate. The exceptional catalytic performance of the chromium catalysts is explained by their unique ability to catalyze glucose to fructose isomerization and fructose to HMF dehydration with high selectivity. Side reactions leading to humins by means of condensation reactions take predominantly place during fructose dehydration. The higher HMF selectivity for Cr(III) is tentatively explained by the higher activity in fructose dehydration compared to Cr(II) . This limits the concentration of intermediates that are involved in bimolecular condensation reactions. Model DFT calculations indicate a substantially lower activation barrier for glucose isomerization by Cr(III) compared to Cr(II) . Qualitatively, glucose isomerization follows a similar mechanism for Cr(II) and Cr(III) . The mechanism involves ring opening of D-glucopyranose coordinated to a single Cr ion, followed by a transient self-organization of catalytic chromium complexes that promotes the rate-determining hydrogen-shift step.

  18. Oxygen and chromium self-diffusion in Cr sub(2)O sub(3)

    International Nuclear Information System (INIS)

    The oxygen and chromium diffusivities in Cr sub(2)O sub(3) single crystals and polycrystals were determined by ion implantation, thick film methods, and isotopic exchange, using the sup(54)Cr, sup(5)Cr and sup(18)O isotopes. Depth profiling was made by SIMS, and the diffusion coefficients were computed using a general solution of the Fick's law taking into account evaporation and exchange at the surface. Lattice and grain boundary self-diffusion coefficients were determined as a function of temperature and oxygen pressure. (author)

  19. 7 CFR 900.54 - Docket number.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Docket number. 900.54 Section 900.54 Agriculture... Governing Proceedings on Petitions To Modify or To Be Exempted From Marketing Orders § 900.54 Docket number. Each proceeding, immediately following its institution, shall be assigned a docket number by...

  20. 28 CFR 54.405 - Housing.

    Science.gov (United States)

    2010-07-01

    ... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Housing. 54.405 Section 54.405 Judicial... Activities Prohibited § 54.405 Housing. (a) Generally. A recipient shall not, on the basis of sex, apply... benefits related to housing, except as provided in this section (including housing provided only to...

  1. 46 CFR 503.54 - Original classification.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 9 2010-10-01 2010-10-01 false Original classification. 503.54 Section 503.54 Shipping... Program § 503.54 Original classification. (a) No Commission Member or employee has the authority to... require classification, or receives any foreign government information as defined in section 1.1(d)...

  2. 27 CFR 31.54 - Hospitals.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Hospitals. 31.54 Section 31.54 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF... Registration And/or Recordkeeping § 31.54 Hospitals. Hospitals and similar institutions furnishing liquors...

  3. 28 CFR 54.310 - Recruitment.

    Science.gov (United States)

    2010-07-01

    ... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Recruitment. 54.310 Section 54.310... in Admission and Recruitment Prohibited § 54.310 Recruitment. (a) Nondiscriminatory recruitment. A... recruitment and admission of students. A recipient may be required to undertake additional recruitment...

  4. 28 CFR 54.510 - Recruitment.

    Science.gov (United States)

    2010-07-01

    ... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Recruitment. 54.510 Section 54.510... in Employment in Education Programs or Activities Prohibited § 54.510 Recruitment. (a) Nondiscriminatory recruitment and hiring. A recipient shall not discriminate on the basis of sex in the...

  5. 28 CFR 54.540 - Advertising.

    Science.gov (United States)

    2010-07-01

    ... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Advertising. 54.540 Section 54.540... in Employment in Education Programs or Activities Prohibited § 54.540 Advertising. A recipient shall not in any advertising related to employment indicate preference, limitation, specification,...

  6. 40 CFR 68.54 - Training.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 15 2010-07-01 2010-07-01 false Training. 68.54 Section 68.54... ACCIDENT PREVENTION PROVISIONS Program 2 Prevention Program § 68.54 Training. (a) The owner or operator... covered process have been trained or tested competent in the operating procedures provided in § 68.52...

  7. 49 CFR 195.54 - Accident reports.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Accident reports. 195.54 Section 195.54... PIPELINE Annual, Accident, and Safety-Related Condition Reporting § 195.54 Accident reports. (a) Each operator that experiences an accident that is required to be reported under § 195.50 shall as soon...

  8. 7 CFR 906.54 - Effective time.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Effective time. 906.54 Section 906.54 Agriculture... RIO GRANDE VALLEY IN TEXAS Order Regulating Handling Miscellaneous Provisions § 906.54 Effective time. The provisions of this subpart, or any amendment thereto, shall become effective at such time as...

  9. 40 CFR 205.54 - Test procedures.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Test procedures. 205.54 Section 205.54 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) NOISE ABATEMENT PROGRAMS TRANSPORTATION EQUIPMENT NOISE EMISSION CONTROLS Medium and Heavy Trucks § 205.54 Test procedures. The procedures...

  10. 10 CFR 54.43 - Criminal penalties.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Criminal penalties. 54.43 Section 54.43 Energy NUCLEAR... General Provisions § 54.43 Criminal penalties. (a) Section 223 of the Atomic Energy Act of 1954, as amended, provides for criminal sanctions for willful violations of, attempted violation of, or...

  11. 42 CFR 21.54 - Students.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 1 2010-10-01 2010-10-01 false Students. 21.54 Section 21.54 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES PERSONNEL COMMISSIONED OFFICERS Appointment § 21.54 Students. A potential candidate for appointment in the Regular Corps who is pursuing a course of instruction which, upon completion,...

  12. 28 CFR 54.525 - Fringe benefits.

    Science.gov (United States)

    2010-07-01

    ... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Fringe benefits. 54.525 Section 54.525... in Employment in Education Programs or Activities Prohibited § 54.525 Fringe benefits. (a) “Fringe benefits” defined. For purposes of these Title IX regulations, fringe benefits means: Any medical,...

  13. 47 CFR 54.516 - Auditing.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 3 2010-10-01 2010-10-01 false Auditing. 54.516 Section 54.516... SERVICE Universal Service Support for Schools and Libraries § 54.516 Auditing. (a) Recordkeeping... records of equipment purchased as components of supported internal connections services sufficient...

  14. 28 CFR 345.54 - Overtime compensation.

    Science.gov (United States)

    2010-07-01

    ... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Overtime compensation. 345.54 Section 345.54 Judicial Administration FEDERAL PRISON INDUSTRIES, INC., DEPARTMENT OF JUSTICE FEDERAL PRISON INDUSTRIES (FPI) INMATE WORK PROGRAMS Inmate Pay and Benefits § 345.54 Overtime compensation. An...

  15. 45 CFR 86.54 - Compensation.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 1 2010-10-01 2010-10-01 false Compensation. 86.54 Section 86.54 Public Welfare... in Employment in Education Programs or Activities Prohibited § 86.54 Compensation. A recipient shall... of pay or other compensation; (b) Results in the payment of wages to employees of one sex at a...

  16. 7 CFR 15a.54 - Compensation.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 1 2010-01-01 2010-01-01 false Compensation. 15a.54 Section 15a.54 Agriculture Office... Activities Prohibited § 15a.54 Compensation. A recipient shall not make or enforce any policy or practice which, on the basis of sex: (a) Makes distinctions in rates of pay or other compensation; (b) Results...

  17. 28 CFR 54.515 - Compensation.

    Science.gov (United States)

    2010-07-01

    ... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Compensation. 54.515 Section 54.515... in Employment in Education Programs or Activities Prohibited § 54.515 Compensation. A recipient shall... of pay or other compensation; (b) Results in the payment of wages to employees of one sex at a...

  18. 7 CFR 1700.54 - Electric Program.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 11 2010-01-01 2010-01-01 false Electric Program. 1700.54 Section 1700.54 Agriculture... GENERAL INFORMATION Loan and Grant Approval Authorities § 1700.54 Electric Program. (a) Administrator: The... Administrator, Electric Program, has the authority to approve the following loans, loan guarantees, and...

  19. 7 CFR 54.1033 - Confidential treatment.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Confidential treatment. 54.1033 Section 54.1033 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... and Poultry Products § 54.1033 Confidential treatment. Every design review specialist...

  20. 7 CFR 989.54 - Marketing policy.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Marketing policy. 989.54 Section 989.54 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... CALIFORNIA Order Regulating Handling Marketing Policy § 989.54 Marketing policy. (a) Trade demand. On...

  1. Electrodeposition of black chromium thin films from trivalent chromium-ionic liquid solution

    OpenAIRE

    Eugénio, S.; Vilar, Rui; C. M. Rangel; Baskaran, I.

    2009-01-01

    In the present study, black chromium thin films were electrodeposited from a solution of 1-butyl-3- methylimidazolium tetrafluoroborate ([BMIm][BF4] ionic liquid containing trivalent chromium (Cr(III)). Homogeneous and well adherent coatings have been obtained on nickel, copper and stainless steel substrates. The nucleation and growth of the films were investigated by cyclic voltammetry and current-density/time transient techniques. SEM/EDS, XPS and XRD were used to study the morphology, chem...

  2. Reduction of Hexavalent Chromium by Viable Cells of Chromium Resistant Bacteria Isolated from Chromite Mining Environment

    OpenAIRE

    Satarupa Dey; Baishali Pandit; A. K. Paul

    2014-01-01

    Environmental contamination of hexavalent chromium [Cr(VI)] is of serious concern for its toxicity as well as mutagenic and carcinogenic effects. Bacterial chromate reduction is a cost-effective technology for detoxification as well as removal of Cr(VI) from polluted environment. Chromium resistant and reducing bacteria, belonging to Arthrobacter, Pseudomonas, and Corynebacterium isolated from chromite mine overburden and seepage samples of Orissa, India, were found to tolerate 12–18 mM Cr(VI...

  3. Reduction of Chromium-VI by Chromium Resistant Lactobacilli: A Prospective Bacterium for Bioremediation

    OpenAIRE

    Mishra, Ritesh; Sinha, Vartika; Kannan, Ambrose; Upreti, Raj K.

    2012-01-01

    Chromium is a toxic heavy metal, which primarily exists in two inorganic forms, Cr (VI) and Cr (III). Highly soluble hexavalent chromium is carcinogenic due to its oxidizing nature. It is well established that the intestinal bacteria including Lactobacilli have regulatory effect on intestinal homeostasis and a breakdown in the relationship between intestinal cells and bacteria results in the manifestation of gastrointestinal (GI) disorders. In this study Cr (VI) resistance was developed in La...

  4. The electronic structure of antiferromagnetic chromium

    DEFF Research Database (Denmark)

    Skriver, Hans Lomholt

    1981-01-01

    The author has used the local spin density formalism to perform self-consistent calculations of the electronic structure of chromium in the non-magnetic and commensurate antiferromagnetic phases, as a function of the lattice parameter. A change of a few per cent in the atomic radius brings...

  5. Flashlamp-pumped lasing of chromium: GSGG

    International Nuclear Information System (INIS)

    Lasing action in chromium-doped gadolinium scandium gallium garnet (Cr:GSGG) is well established for both CW/sup (1)/ and flashlamp/sup (2)/ pumping. This paper describes an investigation of flashlamp-pumped Cr:GSGG lasers and indicates some of the factors which limit performance

  6. Defect structure of electrodeposited chromium layers

    CERN Document Server

    Marek, T; Vertes, A; El-Sharif, M; McDougall, J; Chisolm, C U

    2000-01-01

    Positron annihilation spectroscopy was applied to study the effects of pre-treatment and composition of substrates on the quality and defect structure of electrodeposited thick chromium coatings. The results show that both parameters are important, and a scenario is proposed why the mechanically polished substrate gives more defective film than the electro polished one.

  7. 29 CFR 1910.1026 - Chromium (VI).

    Science.gov (United States)

    2010-07-01

    ... Enhancements In Lieu of LEV Retrofitting • Eductors. Many chemical baths are currently mixed via air agitation... requirements of the Hazard Communication Standard, 29 CFR 1910.1200. (3) Cleaning and replacement. (i) The... CFR 1910.141. Where skin contact with chromium (VI) occurs, the employer shall provide...

  8. Biological groundwater treatment for chromium removal at low hexavalent chromium concentrations.

    Science.gov (United States)

    Mamais, Daniel; Noutsopoulos, Constantinos; Kavallari, Ioanna; Nyktari, Eleni; Kaldis, Apostolos; Panousi, Eleni; Nikitopoulos, George; Antoniou, Kornilia; Nasioka, Maria

    2016-06-01

    The objective of this work is to develop and evaluate biological groundwater treatment systems that will achieve hexavalent chromium reduction and total chromium removal from groundwater at hexavalent chromium (Cr(VI)) groundwater concentrations in the 0-200 μg/L range. Three lab-scale units operated, as sequencing batch reactors (SBR) under aerobic, anaerobic and anaerobic-aerobic conditions. All systems received groundwater with a Cr(VI) content of 200 μg/L. In order to support biological growth, groundwater was supplemented with milk, liquid cheese whey or a mixture of sugar and milk to achieve a COD concentration of 200 mg/L. The results demonstrate that a fully anaerobic system or an anaerobic-aerobic system dosed with simple or complex external organic carbon sources can lead to practically complete Cr(VI) reduction to Cr(III). The temperature dependency of maximum Cr(VI) removal rates can be described by the Arrhenius relationship. Total chromium removal in the biological treatment systems was not complete because a significant portion of Cr(III) remained in solution. An integrated system comprising of an anaerobic SBR followed by a sand filter achieved more than 95% total chromium removal thus resulting in average effluent total and dissolved chromium concentrations of 7 μg/L and 3 μg/L, respectively. PMID:26971177

  9. Chromium(III) and chromium(VI) surface treated galvanized steel for outdoor constructions: environmental aspects.

    Science.gov (United States)

    Lindström, David; Hedberg, Yolanda; Odnevall Wallinder, Inger

    2010-06-01

    The long-term degradation of chromium(III) (Zn-Cr(III)) and chromium(VI)-based (Zn-Cr(VI)) surface treatments on galvanized steel and their capacities to hinder the release of zinc induced by atmospheric corrosion at nonsheltered urban and marine exposure conditions for 2 years are investigated. Compared to bare zinc sheet, both surface treatments revealed high corrosion protection abilities and capacities to hinder the release of zinc, still evident after 2 years of exposure. The zinc barrier properties of the thinner Zn-Cr(VI) (10 nm) treatment were during the first 100 days of urban exposure slightly improved compared with Zn-Cr(III) (35 nm). However, their long-term protection capacities were inverse. Released concentrations of total chromium correspond to annual release rates less than 0.000032 (Zn-Cr(III)) and 0.00014 g Cr m(-2) yr(-1) (Zn-Cr(VI)) after 1 year of urban exposure. Aging by indoor storage of the surface treatments prior to outdoor exposure reduced the released Cr concentrations from the surface treatments. No Cr(VI) was released from the aged surfaces but from the freshly exposed Zn-Cr(VI). Marine exposure conditions resulted in a faster reduction of chromate to chromium(III)oxide compared with urban conditions, and a significantly lower amount of both chromium(III) and chromium(VI) released from Zn-Cr(VI) at the marine site compared with the urban site. PMID:20462267

  10. Impact of incorporation of chromium on electrochemical properties of LiFePO4/C for Li-ion batteries

    OpenAIRE

    Naik Amol; Zhou Jian; Gao Chao; Liu Guizhen; Wang Lin

    2015-01-01

    LiFe0.95Cr0.05PO4/C was successfully synthesized by one-step solid-state reaction using a single mode microwave reactor. The effect of incorporation of chromium on LiFePO4 lattice parameters was systematically investigated by X-ray diffraction. Surface analysis was done by scanning electron microscopy and transmission electron microscopy. The ratio of amorphous to graphitic carbon was determined from Raman spectroscopic data. The influence of chromium incorporation on electrochemical properti...

  11. Assessment of chromium biostabilization in contaminated soils using standard leaching and sequential extraction techniques

    International Nuclear Information System (INIS)

    The iron reducing microorganism Desulfuromonas palmitatis was evaluated as potential biostabilization agent for the remediation of chromate contaminated soils. D. palmitatis were used for the treatment of soil samples artificially contaminated with Cr(VI) at two levels, i.e. 200 and 500 mg kg-1. The efficiency of the treatment was evaluated by applying several standard extraction techniques on the soil samples before and after treatment, such as the EN12457 standard leaching test, the US EPA 3060A alkaline digestion method and the BCR sequential extraction procedure. The water soluble chromium as evaluated with the EN leaching test, was found to decrease after the biostabilization treatment from 13 to less than 0.5 mg kg-1 and from 120 to 5.6 mg kg-1 for the soil samples contaminated with 200 and 500 mg Cr(VI) per kg soil respectively. The BCR sequential extraction scheme, although not providing accurate estimates about the initial chromium speciation in contaminated soils, proved to be a useful tool for monitoring the relative changes in element partitioning, as a consequence of the stabilization treatment. After bioreduction, the percentage of chromium retained in the two least soluble BCR fractions, i.e. the 'oxidizable' and 'residual' fractions, increased from 54 and 73% to more than 96% in both soils

  12. Attenuation of Chromium toxicity in mine waste water using water hyacinth

    Directory of Open Access Journals (Sweden)

    Mohanty M.

    2011-12-01

    Full Text Available The mine waste water at South Kaliapani chromite mining area of Orissa (India showed high levels of toxic hexavalent chromium (Cr+6. Cr+6 contaminated mine waste water poses potential threats for biotic community in the vicinity. The current field based phytoremediation study is an in situ approach for attenuation of Cr+6 from mine waste water using water hyacinth (Eichhornia crassipes weeds by rhizofiltration method. The weeds significantly reduced (up to 54% toxic concentrations of Cr+6 from contaminated mine waste water when passed through succeeding water hyacinth ponds. The reduction of toxic chromium level varied with the plant age and passage distance of waste water. Chromium phytoaccumulation and Bio-Concentration Factor (BCF was maximum at growing stage of plant i.e. 75 days old plant. High BCF (10,924 and Transportation Index (32.09 for water hyacinth indicated that the weeds can be used as a tool of phytoremediation to combat the problem of in situ Cr contamination in mining areas.

  13. Chromium poisoning in (La,Sr)MnO3 cathode: Three-dimensional simulation of a solid oxide fuel cell

    Science.gov (United States)

    Miyoshi, Kota; Iwai, Hiroshi; Kishimoto, Masashi; Saito, Motohiro; Yoshida, Hideo

    2016-09-01

    A three-dimensional numerical model of a single solid oxide fuel cell (SOFC) considering chromium poisoning on the cathode side has been developed to investigate the evolution of the SOFC performance over long-term operation. The degradation model applied in the simulation describes the loss of the cathode electrochemical activity as a decrease in the active triple-phase boundary (TPB) length. The calculations are conducted for two types of cell: lanthanum strontium manganite (LSM)/yttria-stabilized zirconia (YSZ)/Ni-YSZ and LSM-YSZ/YSZ/Ni-YSZ. Their electrode microstructures are acquired by imaging with a focused ion beam scanning-electron microscope (FIB-SEM). The simulation results qualitatively reproduce the trends of chromium poisoning reported in the literature. It has been revealed that the performance degradation by chromium is primarily due to an increase in the cathode activation overpotential. In addition, in the LSM-YSZ composite cathode, TPBs in the vicinity of the cathode-electrolyte interface preferentially deteriorate, shifting the active reaction site towards the cathode surface. This also results in an increase in the cathode ohmic loss associated with oxide ion conduction through the YSZ phase. The effects of the cell temperature, the partial pressure of steam at the chromium source, the cathode microstructure, and the cathode thickness on chromium poisoning are also discussed.

  14. CHROMIUM INDUCED CYTOTOXICITY IN BLACKGRAM (VIGNA MUNGO L.

    Directory of Open Access Journals (Sweden)

    A. Chidambaram ، P. Sundaramoorthy ، A. Murugan ، K. Sankar Ganesh ، L. Baskaran

    2009-01-01

    Full Text Available Chromium is known to be highly toxic to biological systems. This study was designed to determine the mutagenic effects of different concentrations (0, 10, 25, 50, 100 and 200 mg/L of hexavalent chromium on root tip cells of blackgram (Vigna mungo L. Hepper. The blackgram seeds were equi-spacially arranged in sterilized petriplates lined with filter paper and they were treated with different concentrations of chromium solution. In germination studies, the morphological growth parameters such as germination percentage, root length, shoot length fresh weight and dry weight of blackgram seedlings were decreased with increasing dose of chromium concentrations. No germination of blackgram seeds was recorded at 300mg/l chromium concentration. Chromosome aberration assay was used to determine the mitotic indices and rate of chromosome aberration in blackgram root tip cells due to chromium treatment. The results showed that the mitotic indices were complicated due to different concentrations of chromium. However, the increase in chromium concentration has led to a gradual increase in the percentage of chromosomal aberration and mitotic index. The chromosome length, absolute chromosome length and average chromosome lengths were gradually found to decrease. There was no considerable change in 2n number of chromosome with the increase in chromium concentrations. It is concluded that the hexavalent chromium has significant mutagenic effect on the root tip cells of blackgram.

  15. Chromium supplementation improved post-stroke brain infarction and hyperglycemia.

    Science.gov (United States)

    Chen, Wen-Ying; Mao, Frank Chiahung; Liu, Chia-Hsin; Kuan, Yu-Hsiang; Lai, Nai-Wei; Wu, Chih-Cheng; Chen, Chun-Jung

    2016-04-01

    Hyperglycemia is common after acute stroke and is associated with a worse outcome of stroke. Thus, a better understanding of stress hyperglycemia is helpful to the prevention and therapeutic treatment of stroke. Chromium is an essential nutrient required for optimal insulin activity and normal carbohydrate and lipid metabolism. Beyond its nutritional effects, dietary supplement of chromium causes beneficial outcomes against several diseases, in particular diabetes-associated complications. In this study, we investigated whether post-stroke hyperglycemia involved chromium dynamic mobilization in a rat model of permanent focal cerebral ischemia and whether dietary supplement of chromium improved post-stroke injury and alterations. Stroke rats developed brain infarction, hyperglycemia, hyperinsulinemia, glucose intolerance, and insulin resistance. Post-stroke hyperglycemia was accompanied by elevated secretion of counter-regulatory hormones including glucagon, corticosterone, and norepinephrine, decreased insulin signaling in skeletal muscles, and increased hepatic gluconeogenesis. Correlation studies revealed that counter-regulatory hormone secretion showed a positive correlation with chromium loss and blood glucose increased together with chromium loss. Daily chromium supplementation increased tissue chromium levels, attenuated brain infarction, improved hyperglycemia, and decreased plasma levels of glucagon and corticosterone in stroke rats. Our findings suggest that stroke rats show disturbance of tissue chromium homeostasis with a net loss through urinary excretion and chromium mobilization and loss might be an alternative mechanism responsible for post-stroke hyperglycemia. PMID:26477944

  16. Improvement on simultaneous determination of chromium species in aqueous solution by ion chromatography and chemiluminescence detection

    DEFF Research Database (Denmark)

    Gammelgaard, Bente; Liao, Y.P.; Jons, O.

    1997-01-01

    A sensitive method for the simultaneous determination of chromium(III) and chromium(VI) was chromatography and chemiluminescence detection. Two Dionex ion-exchange guard columns in series, CG5 and AG7, were used to separate chromium(III) from chromium(VI). Chromium(VI) was reduced by potassium su...

  17. Interactions of chromium ions with starch granules in an aqueous environment.

    Science.gov (United States)

    Szczygieł, Jadwiga; Dyrek, Krystyna; Kruczała, Krzysztof; Bidzińska, Ewa; Brożek-Mucha, Zuzanna; Wenda, Elżbieta; Wieczorek, Jerzy; Szymońska, Joanna

    2014-06-26

    In this study, interactions of dichromate ions with potato starch granules in highly acidic aqueous solutions and at different temperatures were investigated. It was found that the process underwent a reduction of Cr(2)O(7)(2-) to Cr(3+) accompanied by the formation of intermediate Cr(5+) ions detected by electron paramagnetic resonance (EPR) spectroscopy. The reactions took place after the attachment of dichromate anions to the granules and resulted in a lowering of the Cr(2)O(7)(2-) initial content in the solution. The newly formed Cr(3+) ions were both accumulated by the granules or remained in the solution. It was observed for the first time that the quantity of such ions taken by the granules from the solution was noticeably higher than that delivered by trivalent chromium salt solution. It was revealed by scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM-EDX) that the chromium ions were not only adsorbed on the granule surface but also introduced into the granule interior and evenly distributed there. An activation energy of the reduction reaction equal to 65 kJ·mol(-1) and the optimal parameters of the process were established. The proposed mechanism could be useful for the bioremediation of industrial effluents polluted by hexavalent chromium compounds.

  18. [Experimental study on the remediation of chromium contaminated groundwater with PRB media].

    Science.gov (United States)

    Zhu, Wen-Hui; Dong, Liang-Fei; Wang, Xing-Run; Zhai, Ya-Li

    2013-07-01

    Due to the surface reaction between zero-valent iron and Cr(VI), iron cannot be fully utilized in the Fe(0)-Permeable Reactive Barrier(PRB), and the PRB is prone to compaction and blockage. In order to resolve these problems, iron powder coated with different polymer was tested in the treatment of chromium-polluted groundwater. Experimental results demonstrated that sodium alginate (SA) was the best package materials. According to analysis with FEI and EDX, pore structures were created by cross-linking of SA with Ca2+, in which a lot of attaching points exist, and through which Cr(VI) could react with interior iron powder. SA coating cast iron (SAC) and reduced iron (SAR) were tested in the treatment of chromium-polluted groundwater individually; the results showed that the removal efficiency of Cr( VI) by SAC was double that by SAR. After optimization of technology parameters of SAC, the Cr(VI) removal process follows the pseudo first-order kinetics. Based on dynamic experiments with SAC, Cr(VI)/Fe(0) was up to 32.25 mg x g(-1) and the PRB maintained high permeability coefficient (2.38 cm x s(-1)) after complete reaction. Compared with cast iron media is feasible in the remediation of chromium contaminated groundwater. PMID:24028003

  19. Femtosecond laser surface structuring and oxidation of chromium thin coatings: Black chromium

    International Nuclear Information System (INIS)

    Highlights: • Oxidation of the chromium thin film to chromium oxide by femtosecond laser with a fundamental wavelength of 1064 nm. • Solar absorber from chromium oxide that low percentage reflectance. • Femtosecond laser oxidation, with a de-focused laser. • Chromium oxide formation by femtosecond laser in normal ambient. - Abstract: In view of their potential applications as selective solar absorbers, chromium coatings on float glass substrates were nano/micro structured by femtosecond laser in air. Raman and X-rays diffraction investigations confirmed the formation of an ultra-porous α-Cr2O3 layer at the surface; higher is the input laser power, enhanced is the crystallinity of the α-Cr2O3 layer. The α-Cr2O3 layer with the Cr underneath it in addition to the photo-induced porosity acted as a classical ceramic–metal nano-composite making the reflectance to decrease significantly within the spectral range of 190–1100 nm. The average reflectance decreased from 70 to 2%

  20. Femtosecond laser surface structuring and oxidation of chromium thin coatings: Black chromium

    Energy Technology Data Exchange (ETDEWEB)

    Kotsedi, L., E-mail: Kotsedi@tlabs.ac.za [UNESCO-UNISA Africa Chair in Nanosciences-Nanotechnology, College of Graduate Studies, University of South Africa, Muckleneuk Ridge, P.O. Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, Somerset West 7129, P.O. Box 722, Somerset West, Western Cape (South Africa); Nuru, Z.Y. [UNESCO-UNISA Africa Chair in Nanosciences-Nanotechnology, College of Graduate Studies, University of South Africa, Muckleneuk Ridge, P.O. Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, Somerset West 7129, P.O. Box 722, Somerset West, Western Cape (South Africa); Mthunzi, P. [National Laser Centre, Council for Scientific and Industrial Research, 0001 Pretoria (South Africa); Muller, T.F.G. [University of the Western Cape, Physics Department, Bellville, 7535 Cape Town (South Africa); Eaton, S.M. [Physics Department, Politecnico di Milano, Piazza Leonardo Da Vinci, 32, 20133 Milano (Italy); Julies, B. [University of the Western Cape, Physics Department, Bellville, 7535 Cape Town (South Africa); Manikandan, E. [UNESCO-UNISA Africa Chair in Nanosciences-Nanotechnology, College of Graduate Studies, University of South Africa, Muckleneuk Ridge, P.O. Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, Somerset West 7129, P.O. Box 722, Somerset West, Western Cape (South Africa); Ramponi, R. [Physics Department, Politecnico di Milano, Piazza Leonardo Da Vinci, 32, 20133 Milano (Italy); Maaza, M. [UNESCO-UNISA Africa Chair in Nanosciences-Nanotechnology, College of Graduate Studies, University of South Africa, Muckleneuk Ridge, P.O. Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, Somerset West 7129, P.O. Box 722, Somerset West, Western Cape (South Africa)

    2014-12-01

    Highlights: • Oxidation of the chromium thin film to chromium oxide by femtosecond laser with a fundamental wavelength of 1064 nm. • Solar absorber from chromium oxide that low percentage reflectance. • Femtosecond laser oxidation, with a de-focused laser. • Chromium oxide formation by femtosecond laser in normal ambient. - Abstract: In view of their potential applications as selective solar absorbers, chromium coatings on float glass substrates were nano/micro structured by femtosecond laser in air. Raman and X-rays diffraction investigations confirmed the formation of an ultra-porous α-Cr{sub 2}O{sub 3} layer at the surface; higher is the input laser power, enhanced is the crystallinity of the α-Cr{sub 2}O{sub 3} layer. The α-Cr{sub 2}O{sub 3} layer with the Cr underneath it in addition to the photo-induced porosity acted as a classical ceramic–metal nano-composite making the reflectance to decrease significantly within the spectral range of 190–1100 nm. The average reflectance decreased from 70 to 2%.

  1. 32 CFR 842.54 - Attorney fees.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 6 2010-07-01 2010-07-01 false Attorney fees. 842.54 Section 842.54 National... CLAIMS Military Claims Act (10 U.S.C. 2733) § 842.54 Attorney fees. In the settlement of any claim pursuant to 10 U.S.C. 2733 and this subpart, attorney fees will not exceed 20 percent of any award...

  2. Synthesis and Characterization of Chromium Oxide Nanoparticles

    Directory of Open Access Journals (Sweden)

    Vivek Sheel Jaswal

    2014-06-01

    Full Text Available Chromium oxide nanoparticles (NPshave been rapidly synthesized by precipitation method using ammomia as precipitating agent and are characterized by using X-ray Diffraction (XRD, Thermo Gravimetric Analysis (TGA, UV-Visible absorption (UV, Infrared Spectoscopy (IR, Scanning Electron Microscopy (SEM and Transmission Electron Microscopy (TEM. XRD studies show that chromium oxide NP is formed as Cr2O3 and it has hexagonal structure. The shape and particle size of the synthesized Cr2O3 NPs is determined by SEM and TEM. The images showed that the size of NPs of Cr2O3 varied from 20 nm to 70 nm with average crystalline size 45 nm. UV-Visible absorption and IR spectoscopy confirm the formation of nanosized Cr2O3. TGA verifies that the Cr2O3 NPs are thermally stable upto 1000 °C.

  3. Optical and structural properties of chromium impurities in niobium–gallium oxide

    Energy Technology Data Exchange (ETDEWEB)

    Costa, G.K.B. [Instituto de Física, Universidade do Estado do Rio de Janeiro, Rio de Janeiro, RJ 20559-900 (Brazil); Departamento de Física, Pontifícia Universidade Católica do Rio de Janeiro, Rio de Janeiro, RJ 22453-900 (Brazil); López, A. [Instituto de Física, Universidade do Estado do Rio de Janeiro, Rio de Janeiro, RJ 20559-900 (Brazil); Carvalho, I.C.S. [Departamento de Física, Pontifícia Universidade Católica do Rio de Janeiro, Rio de Janeiro, RJ 22453-900 (Brazil); Nakamura, O. [Instituto de Física, Universidade Federal da Bahia, Salvador, BA 40210-340 (Brazil); Cella, N. [Instituto Politécnico, Universidade do Estado do Rio de Janeiro, P.O. Box 97282, Nova Friburgo, RJ 28601-970 (Brazil); Sosman, L.P., E-mail: sosman@uerj.br [Instituto de Física, Universidade do Estado do Rio de Janeiro, Rio de Janeiro, RJ 20559-900 (Brazil)

    2014-12-15

    In this work, the optical properties of the gallium–niobium oxide doped with chromium ions were investigated. The samples were obtained by wet chemical and solid-state methods, investigated by X-ray powder diffraction and the data were refined by Rietveld methods. The morphology was determined by scanning electron microscope (SEM) images. The photoluminescence, excitation and photoacoustic measurements showed broad and intense bands in the red region of the spectrum, associated with energy transitions of chromium ions in octahedral sites. From the optical spectra and using the crystal field theory, the energy parameters were obtained. - Highlights: • Cr{sup 3+} doped niobium–gallium oxides were prepared by solid state reaction and wet chemical method. • We show bands in red region. • Spectra are associated to Cr{sup 3+} ions in octahedral sites.

  4. Stainless chromium-nickel steels. Chapter I

    International Nuclear Information System (INIS)

    The chemical composition is tabulated of 90 chromium-nickel stainless steels and alloys given in volume %. The values are also given of the corrosion resistance of the steels and alloys. The tables show data on the surface condition or the methods of material working, types and chemical composition of the medium where corrosion resistance tests were carried out, temperature, pressure, time of tests, corrosion rates, corrosion types, and literature references. A total of 35 references is given. (J.B.)

  5. Chromium--a material for fusion technology

    International Nuclear Information System (INIS)

    Due to their low neutron-induced radioactivity chromium based materials are considered to be candidates for structure materials in fusion technology. In this paper investigations are presented of unirradiated chromium with a purity of 99.96% (DUCROPUR) and a dispersion strengthened chromium alloy Cr5Fe1Y2O3 (DUCROLLOY). Both materials have been produced in a powder metallurgical route. Mechanical tests of smooth and pre-cracked specimens have been performed in a wide temperature range. Below 280 deg. C the fracture toughness values of DUCROPUR are very low (1/2), above the transition temperature they exceed 500 MPa m1/2. Large plastic deformations have been observed. DUCROLLOY does not indicate such a significant increase of fracture toughness in the tested temperature range. But above 400 deg. C large plastic deformations can be obtained in bending samples, too. The fatigue crack propagation behaviour of DUCROPUR at 300 deg. C is similar to that of a ductile metal

  6. Chromium Enrichment on P11 Ferritic Steel by Pack Cementation

    Directory of Open Access Journals (Sweden)

    Fauzi F. A.

    2016-01-01

    Full Text Available The future thermal power plant is expected to operate at higher temperature to improve its efficiency and to reduce greenhouse gas emission. This target requires better corrosion properties of ferritic steels, which commonly used as materials for superheater and reheater of boiler tubes. In this work, chromium enrichment on the surface of ferritic steel is studied. The deposited chromium is expected to become a reservoir for the formation of chromia protective layer. Chromium was deposited on the substrate of steel by pack cementation process for two hours at the temperature of 850ºC, 950ºC and 1050ºC, respectively. XRD analysis indicated that chromium was successfully deposited at all temperatures. Somehow, SEM cross sectional image showed that continuous layer of chromium was not continuously formed at 850oC. Therefore, this research clarify that chromium enrichment by pack cementation may be conducted at the temperature above 950°C.

  7. New technology for comprehensive utilization of aluminum-chromium residue from chromium salts production

    Institute of Scientific and Technical Information of China (English)

    LI Xiao-bin; QI Tian-gui; JIANG Xin-min; ZHOU Qiu-sheng; LIU Gui-hua; PENG Zhi-hong; HAN Deng-lun; ZHANG Zhong-yuan; YANG Kun-shan

    2008-01-01

    Colloidal aluminum-chromium residue(ACR) was mass-produced in chromate production process, and the large energy consumption and high recovery cost existed in traditional methods of utilizing such ACR. To overcome those problems, a new comprehensive method was proposed to deal with the ACR, and was proven valid in industry. In the new process, the chromate was separated firstly from the colloidal ACR by ripening and washing with additives, by which more than 95% hexavalent chromium was recovered. The chromium-free aluminum residue(CFAR), after properly dispersed, was digested at 120-130 ℃ and more than 90% alumina can be recovered. And then the pregnant aluminate solution obtained from digestion was seeded to precipitate aluminum hydroxide. This new method can successfully recover both alumina and sodium chromate, and thus realize the comprehensive utilization of ACR from chromate industry.

  8. Liquid Phase Sintering of Boron-Containing Powder Metallurgy Steel with Chromium and Carbon

    Science.gov (United States)

    Wu, Ming-Wei; Fan, Yu-Chi; Huang, Her-Yueh; Cai, Wen-Zhang

    2015-11-01

    Liquid phase sintering is an effective method to improve the densification of powder metallurgy materials. Boron is an excellent alloying element for liquid phase sintering of Fe-based materials. However, the roles of chromium and carbon, and particularly that of the former, on liquid phase sintering are still undetermined. This study demonstrated the effects of chromium and carbon on the microstructure, elemental distribution, boride structure, liquid formation, and densification of Fe-B-Cr and Fe-B-Cr-C steels during liquid phase sintering. The results showed that steels with 0.5 wt pct C densify faster than those without 0.5 wt pct C. Moreover, although only one liquid phase forms in Fe-B-Cr steel, adding 0.5 wt pct C reduces the formation temperature of the liquid phase by about 50 K (°C) and facilitates the formation of an additional liquid, resulting in better densification at 1473 K (1200 °C). In both Fe-B-Cr and Fe-B-Cr-C steels, increasing the chromium content from 1.5 to 3 wt pct raises the temperature of liquid formation by about 10 K (°C). Thermodynamic simulations and experimental results demonstrated that carbon atoms dissolved in austenite facilitate the eutectic reaction and reduce the formation temperature of the liquid phase. In contrast, both chromium and molybdenum atoms dissolved in austenite delay the eutectic reaction. Furthermore, the 3Cr-0.5Mo additive in the Fe-0.4B steel does not change the typical boride structure of M2B. With the addition of 0.5 wt pct C, the crystal structure is completely transformed from M2B boride to M3(B,C) boro-carbide.

  9. Analysis of molybdenum, chromium, vanadium and iron by polarographic techniques

    International Nuclear Information System (INIS)

    The application of direct current Tast polarograph, differential pulse polarography and phase-selective alternative current Tast polarography to the problem of determining molybdenum, chromium, vanadium and iron in various supporting electrolytes is reported. The effect of the supporting electrolyte on the wave/peak potential and sensitivity of the metal ion have been examined. The polarographic methods were applied for simultaneous determination of chromium (3)/chromium (6), vanadium (4), vanadium (5) and iron (2)/iron (3) in different supporting electrolytes

  10. A REVIEW OF BIOSORPTION OF CHROMIUM IONS BY MICROORGANISMS

    OpenAIRE

    Inga Zinicovscaia

    2012-01-01

    Due to its widespread industrial use, chromium has become a serious pollutant in diverse environmental settings. The main source of chromium pollution including the Republic o Moldova is industry. It is a great need to develop new eco-friendly methods of chromium removal. Biosorption of heavy metals is a most promising technology involved in the removal of toxic metals from industrial waste streams and natural waters. This article is an extended abstract of a communication presented at the...

  11. CHROMIUM INDUCED CYTOTOXICITY IN BLACKGRAM (VIGNA MUNGO L.)

    OpenAIRE

    A. Chidambaram ، P. Sundaramoorthy ، A. Murugan ، K. Sankar Ganesh ، L. Baskaran

    2009-01-01

    Chromium is known to be highly toxic to biological systems. This study was designed to determine the mutagenic effects of different concentrations (0, 10, 25, 50, 100 and 200 mg/L) of hexavalent chromium on root tip cells of blackgram (Vigna mungo L. Hepper). The blackgram seeds were equi-spacially arranged in sterilized petriplates lined with filter paper and they were treated with different concentrations of chromium solution. In germination studies, the morphological growth parameters such...

  12. Production of a chromium Bose-Einstein condensate

    OpenAIRE

    Griesmaier, Axel; Stuhler, Jürgen; Pfau, Tilman

    2005-01-01

    The recent achievement of Bose-Einstein condensation of chromium atoms [1] has opened longed-for experimental access to a degenerate quantum gas with long-range and anisotropic interaction. Due to the large magnetic moment of chromium atoms of 6 {$\\mu$}B, in contrast to other Bose- Einstein condensates (BECs), magnetic dipole-dipole interaction plays an important role in a chromium BEC. Many new physical properties of degenerate gases arising from these magnetic forces have been predicted in ...

  13. Increase of chromium utilization in stainless steel melting

    International Nuclear Information System (INIS)

    The processes of deoxidizing when melting stainless 18-10 steels in electric are furnaces by the method of remelting with wastes are investigated. The dependences of amount of reduced chromium on silicon consumption are made more precise. It is shown that it is useful to apply aluminium for deoxidation of acid high-chromium slags. Based on the data on pilot melts the extent to which aluminium can be used as a reducing agent for chromium is estimated. 3 refs., 2 figs

  14. Cutaneous and systemic hypersensitivity reactions to metallic implants

    DEFF Research Database (Denmark)

    Basko-Plluska, Juliana L; Thyssen, Jacob P; Schalock, Peter C

    2011-01-01

    , and vasculitic eruptions may occur. Also, more complex immune reactions may develop around the implants, resulting in pain, inflammation, and loosening. Nickel, cobalt, and chromium are the three most common metals that elicit both cutaneous and extracutaneous allergic reactions from chronic internal exposure...

  15. Chromium depletion from stainless steels during vacuum annealing

    International Nuclear Information System (INIS)

    The behaviour of chromium during selective evaporation by high temperature vacuum annealing has been investigated by means of energy dispersive X-ray analysis and by neutron activation analysis. It was established that the rate of chromium loss from austenitic stainless steels 316 and 321 is controlled by chromium inter-diffusion rather than tracer diffusion in the alloy. Two important parameters in selective removal of chromium from alloy steels are the variation in the chromium surface concentration with time and the depletion profile in the alloy. The present work gives support for the model in which loss of chromium is dependent on its diffusivity in the alloy and on an interface transfer coefficient. The results showed that the surface concentration of chromium decreased with increasing vacuum annealing time. The chromium depletion profile in the metal was in accord with the previous derived model, apart from an anomalous near surface region. Here the higher resolution of a neutron activation technique indicated a region within approximately 2 microns of the surface where the chromium concentration decreased more steeply than expected. (author)

  16. Stabilization and solidification of chromium-contaminated soil

    Energy Technology Data Exchange (ETDEWEB)

    Cherne, C.A.; Thomson, B.M. [Univ. of New Mexico, Albuquerque, NM (United States). Civil Engineering Dept.; Conway, R. [Sandia National Labs., Albuquerque, NM (United States)

    1997-11-01

    Chromium-contaminated soil is a common environmental problem in the United States as a result of numerous industrial processes involving chromium. Hexavalent chromium [Cr(VI)] is the species of most concern because of its toxicity and mobility in groundwater. One method of diminishing the environmental impact of chromium is to reduce it to a trivalent oxidation state [Cr(III)], in which it is relatively insoluble and nontoxic. This study investigated a stabilization and solidification process to minimize the chromium concentration in the Toxicity Characteristic Leaching Procedure (TCLP) extract and to produce a solidified waste form with a compressive strength in the range of 150 to 300 pounds per square inch (psi). To minimize the chromium in the TCLP extract, the chromium had to be reduced to the trivalent oxidation state. The average used in this study was an alluvium contaminated with chromic and sulfuric acid solutions. The chromium concentration in the in the in situ soil was 1212 milligrams per kilogram (mg/kg) total chromium and 275 mg/kg Cr(VI). The effectiveness of iron, ferrous sulfate to reduce Cr(VI) was tested in batch experiments.

  17. Defect transformation in GSGG crystals during chromium ion activation

    International Nuclear Information System (INIS)

    Absorption and induced absorption spectra, dose dependence of induced absorption, thermoluminescence of GSGG crystals, nominally pure and activated with chromium and neodymium ions in different concentrations, are investigated. It is shown that it is chromium ion presence in large concentration that decreases the induced coloration in GSGG crystals after γ-irradiation at 300 K. Optimum concentration of chromium ions for the minimum of induced coloration are found. The mechanism of decrease of induced coloration consisting in Fermi level displacement by chromium ion activation is established. Defect concentration and localization and recombination possibilities of electrons and holes in GSGG crystals are estimated by computer simulation

  18. Tribological Characteristics of Chromium-active Carbon Electroplated Composite Coatings

    Institute of Scientific and Technical Information of China (English)

    GUKa-fi; HUAMeng; Yi-min

    2004-01-01

    A process of chromium electroplating using a standard bath with additives and active carbon particles was reported, and the tribological behaviors of the composite coatings using the pin-on-disk tester and the table wear tester were i nvestig(aed. Experimental results indicate that the electroplated chromium-active carbon composite coatings exhibited the low friction coefficient anti excellent anti-wear properties whets coffered with the normal chromium electroplated ones. The formation of active carbon particles within the chromium matrices can be explained by SEM analysis and the mechanis of wear resistance of the composite coatings were studied.

  19. Method of trivalent chromium concentration determination by atomic spectrometry

    Science.gov (United States)

    Reheulishvili, Aleksandre N.; Tsibakhashvili, Neli Ya.

    2006-12-12

    A method is disclosed for determining the concentration of trivalent chromium Cr(III) in a sample. The addition of perchloric acid has been found to increase the atomic chromium spectrometric signal due to Cr(III), while leaving the signal due to hexavalent chromium Cr(VI) unchanged. This enables determination of the Cr(III) concentration without pre-concentration or pre-separation from chromium of other valences. The Cr(III) concentration may be measured using atomic absorption spectrometry, atomic emission spectrometry or atomic fluorescence spectrometry.

  20. 28 CFR 54.500 - Employment.

    Science.gov (United States)

    2010-07-01

    ... subjected to discrimination in employment, or recruitment, consideration, or selection therefor, whether... §§ 54.500 through 54.550 apply to: (1) Recruitment, advertising, and the process of application for..., layoff, termination, application of nepotism policies, right of return from layoff, and rehiring;...

  1. 47 CFR 54.417 - Recordkeeping requirements.

    Science.gov (United States)

    2010-10-01

    ...) UNIVERSAL SERVICE Universal Service Support for Low-Income Consumers § 54.417 Recordkeeping requirements. (a... resellers that purchase Lifeline discounted wholesale services to offer discounted services to low-income...-income consumers, it constitutes the eligible telecommunications carrier referenced in §§ 54.405(c),...

  2. 40 CFR 30.54 - Quality assurance.

    Science.gov (United States)

    2010-07-01

    ... ADMINISTRATIVE REQUIREMENTS FOR GRANTS AND AGREEMENTS WITH INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, AND OTHER NON-PROFIT ORGANIZATIONS Post-Award Requirements Reports and Records § 30.54 Quality assurance. If the... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Quality assurance. 30.54 Section...

  3. 38 CFR 3.54 - Marriage dates.

    Science.gov (United States)

    2010-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Marriage dates. 3.54..., Compensation, and Dependency and Indemnity Compensation Relationship § 3.54 Marriage dates. A surviving spouse may qualify for pension, compensation, or dependency and indemnity compensation if the marriage to...

  4. 34 CFR 106.54 - Compensation.

    Science.gov (United States)

    2010-07-01

    ... 34 Education 1 2010-07-01 2010-07-01 false Compensation. 106.54 Section 106.54 Education... Compensation. A recipient shall not make or enforce any policy or practice which, on the basis of sex: (a) Makes distinctions in rates of pay or other compensation; (b) Results in the payment of wages...

  5. 9 CFR 54.1 - Definitions.

    Science.gov (United States)

    2010-01-01

    ..., partnership, company, corporation, or any other legal entity who has legal or rightful title to animals... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Definitions. 54.1 Section 54.1 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE...

  6. 15 CFR 923.54 - Mediation.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 3 2010-01-01 2010-01-01 false Mediation. 923.54 Section 923.54... Mediation. (a) Section 307(h) of the Act provides for mediation of serious disagreement between any Federal... cases, mediation by the Secretary, with the assistance of the Executive Office of the President, may...

  7. 21 CFR 640.54 - Processing.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Processing. 640.54 Section 640.54 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) BIOLOGICS ADDITIONAL... storage system. A combination of dry ice and organic solvent may be used for freezing: Provided, That...

  8. Photocatalytic Removal of Hexavalet Chromium and Divalent Nickel fromAqueous Solution by UV Irradiation in the Presence of Titanium Dioxide Vanoparticles

    Directory of Open Access Journals (Sweden)

    M.R Samarghandi

    2010-10-01

    Full Text Available "n "n "nBackgrounds and Objectives: Industrial wastewater included the heavy metal is one of the important sources of environmental pollution. Hexavalent chromiumand divalent nickel are founded in plating wastewater which is harmful for human health and environment. Therefore, the purpose of this research is investigation of photocatalytic removal of hexavalent chromium and divalent nickel from aqueous solution using UV/TiO2 process in a batch system."nMaterials andMethods: At first, reactor was designed. Then, optimumdosage of TiO2 was obtained equal to 1 g/L, with variation TiO2 dosage at constant pH and initial concentrations of hexavalent chromium and divalent nickel. The effect of pH, contact time and initial concentration of hexavalent chromium was studied at the constant amount of TiO2 (1gr/L."nResults: The result showed that photocatalytic removal efficiency increased with increasing reaction time and TiO2 dosage. In addition, it was found that removal efficiency of hexavalent chromium was decreased by increasing initial chromium concentration and pH. But, photocatalytic removal efficiency of nickel ion was increased and decreased by increasing of pH and initial nickel concentration, respectively."nConclusion: The results showed that UV/TiO2 was an effective method in removal of hexavalent chromium and divalent nickel from aqueous solutions

  9. Dehydrogenation of propane in the presence of carbon dioxide over chromium and gallium oxides catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Lapidus, A.L.; Agafonov, Yu.A.; Gaidai, N.A.; Nekrasov, N.V.; Menshova, M.V.; Kunusova, R.M. [Russian Academy of Sciences, Moscow (Russian Federation). N.D. Zelinsky Inst. of Organic Chemistry

    2011-07-01

    Effective chromium and gallium oxides supported catalysts were prepared and tested in longduration experiments for propane dehydrogenation in the presence of CO{sub 2}. The optimal concentrations of active metals were found. It was shown that the activity, selectivity and stability of chromium oxides catalysts were higher than these parameters for gallium ones. Mechanism of propane oxidative dehydrogenation was studied over both catalysts using unstationary and spectroscopic methods. The employment of these methods allowed to establish the differences in process mechanism. It was shown that surface hydroxides took participation in propene formation over Cr-catalysts and hydrides - over Ga-ones. Propane and carbon dioxide participated in the reaction from the adsorbed state over both catalysts but they were differed by the adsorption capacity of the reaction components: CO2 was tied more firmly than C{sub 3}H{sub 6} over both catalysts, CO{sub 2} and C{sub 3}H{sub 6} were tied more strongly with Cr-catalysts than with Ga-ones. It was shown that CO{sub 2} took active participation in reverse watergas shift reaction and in oxidation of catalyst surface over chromium oxides catalysts. The main role of CO{sub 2} in propane dehydrogenation over gallium catalysts consisted in a decrease of coke formation. Step-schemes of propene and cracking products formation were proposed on the basis of literature and obtained data: via the redox mechanism over Cr-catalysts and through a heterolytic dissociation reaction pathway over Ga-ones. (orig.)

  10. Heterogeneous kinetics of the reduction of chromium (VI) by elemental iron

    International Nuclear Information System (INIS)

    Zero valent iron (ZVI) has been extensively used as a reactive medium for the reduction of Cr(VI) to Cr(III) in reactive permeable barriers. The kinetic rate depends strongly on the superficial oxidation of the iron particles used and the preliminary washing of ZVI increases the rate. The reaction has been primarily modelled using a pseudo-first-order kinetics which is inappropriate for a heterogeneous reaction. We assumed a shrinking particle type model where the kinetic rate is proportional to the available iron surface area, to the initial volume of solution and to the chromium concentration raised to a power α which is the order of the chemical reaction occurring at surface. We assumed α = 2/3 based on the likeness to the shrinking particle models with spherical symmetry. Kinetics studies were performed in order to evaluate the suitability of this approach. The influence of the following parameters was experimentally studied: initial available surface area, chromium concentration, temperature and pH. The assumed order for the reaction was confirmed. In addition, the rate constant was calculated from data obtained in different operating conditions. Digital pictures of iron balls were periodically taken and the image treatment allowed for establishing the time evolution of their size distribution.

  11. A Study of Chromium Adsorption on Natural Goethite Biomineralized with Iron Bacteria

    Institute of Scientific and Technical Information of China (English)

    SUN Zhenya; ZHU Chunshui; HUANG Jiangbo; GONG Wenqi; CHEN Hesheng; MU Shanbin

    2006-01-01

    Goethite, especially biogenic goethite, has high specific surface area and great capacity for the adsorption of many contaminants including metal ions and organic chelates. Chromium is a redox actively toxic metal ion that exists as either CrⅢ or CrⅥ in nature, and as such it is essential to understand its behavior of adsorption on natural goethite mineralized by iron bacteria, as Gallionella and Leptothrix in water body. The adsorption of Cr3+ and CrⅥ on naturally biomineralized goethite is studied in this paper. The results show that both Langmuir and Freundlich adsorption isothermal models are able to accurately describe the adsorption of these two ions. Investigation of SEM/EDS,TEM/EDS indicates that the two ions do not adsorb homogeneously on goethite owing to the different microstructures of goethite, and that the microspherical goethite has a greater adsorption capacity for chromium ions than the helical one. XPS data show that redox reaction of chromium on the surface of biomineralized goethite takes place in the adsorption of both Cr3+ and CrⅥ. The CrⅥ adsorbed on biogoethite is much easier to transform into CrⅢ than the oxidization of CrⅢ on the bio-goethite.

  12. IRIS Toxicological Review of Hexavalent Chromium (2010 External Review Draft)

    Science.gov (United States)

    [UPDATE] New Schedule for IRIS Hexavalent Chromium Assessment In Feb 2012, EPA developed a new schedule for completing the IRIS hexavalent chromium assessment. Based on the recommendations of the external peer review panel, which met in May 2011 to review the dra...

  13. Chromium and Polyphenols From Cinnamon Improve Insulin Sensitivity

    Science.gov (United States)

    Naturally occurring compounds that have been shown to improve insulin sensitivity include chromium and polyphenols found in cinnamon. These compounds also have similar effects on insulin signaling and glucose control. The signs of chromium deficiency are similar to those for the metabolic syndrome ...

  14. Safety, absorption, and antioxidant effects of chromium histidine

    Science.gov (United States)

    Supplemental chromium has been shown to be involved in the alleviation of the metabolic syndrome, glucose intolerance, polycystic ovary syndrome, depression, excess body fat, and gestational, steroid-induced, and type 2 diabetes. Chromium amino acid complexes that contained histidine displayed cons...

  15. Residual Chromium in Leather by Instrumental Neutron Activation Analysis

    Directory of Open Access Journals (Sweden)

    S. Okoh

    2012-01-01

    Full Text Available Problem statement: Most tanning processes employ the use of chromium sulphate. For chromium tanned leather, finished products may contain high amount of residual chromium. This may pose some health hazards, since chromium is known to be toxic at elevated concentration. This justifies the need for the study. Approach: Various samples of leather were collected from a tannery, a leather crafts market, a leather dump site and from local tanners all in Kano, Nigeria in 2009. The samples were irradiated for 6 h in the inner site of the Nigerian Research Reactor (NIRR-1 at a flux of 5×1011 ncm-2 sec-1. Results: After evaluating the spectrum, the mean results for chromium in the samples were determined as 2.33±0.3, 2.23±0.3 and 2.93±0.4% for samples from the tannery, leather crafts market and leather dump sites respectively. Chromium concentration in samples collected from local tanners who use tannins from Acacia nilotica as tanning agent was below the detection limit of Instrumental Neutron Activation Analysis (INAA technique used in the study. Conclusion: Although, the concentrations of chromium in the analysed samples were not much higher than what were obtained in literature, they may be enough to sensitize the population that is allergic to chromium.

  16. 47 CFR 54.615 - Obtaining services.

    Science.gov (United States)

    2010-10-01

    ... provided under § 54.621, that the requester cannot obtain toll-free access to an Internet service provider... thing of value; (6) If the service or services are being purchased as part of an aggregated...

  17. CHROMIUM BIOACCUMULATION FROM COMPOSTS AND VERMICOMPOSTS BASED ON TANNERY SLUDGES

    Directory of Open Access Journals (Sweden)

    Krzysztof GONDEK

    2008-07-01

    Full Text Available Storage of waste substances is not indifferent to ecological equilibrium in the environment therefore should not be the ultimate way to limit waste arduousness. Therefore, the conducted investigations aimed to determine the effect of tannery composts and vermicomposts loaded with chromium on this element bioaccumulation in earthworm bodies and biomass of selected plants. Chromium in composts and vermicomposts based on tannery sludges occurred in small quantities and easily soluble compounds. Chromium concentrations in redworm biomass points to this metal accumulation in Eisenia fetida body tissues. This element content in redworm biomass was signifi cantly positively correlated with its content in composts. Chromium content in plants was diversifi ed and on treatments was generally smaller than on mineral treatment or farmyard manure. Chromium absorbed by plants was stored mainly in the root systems, and over the norm content of this element found in vermicomposts did not cause its excessive accumulation in plant biomass.

  18. Bioleaching of chromium from tannery sludge by indigenous Acidithiobacillus thiooxidans.

    Science.gov (United States)

    Wang, Yuan-Shan; Pan, Zhi-Yan; Lang, Jian-Min; Xu, Jian-Miao; Zheng, Yu-Guo

    2007-08-17

    Chromium in tannery sludge will cause serious environmental problems and is toxic to organisms. The acidophilic sulfur-oxidizing Acidithiobacillus thiooxidans can leach heavy metals form urban and industrial wastes. This study examined the ability of an indigenous sulfur-oxidizing A. thiooxidans to leach chromium from tannery sludge. The results showed that the pH of sludge mixture inoculated with the indigenous A. thiooxidans decreased to around 2.0 after 4 days. After 6 days incubation in shaking flasks at 30 degrees C and 160 rpm, up to 99% of chromium was solubilized from tannery sludge. When treated in a 2-l bubble column bioreactor for 5 days at 30 degrees C and aeration of 0.5 vvm, 99.7% of chromium was leached from tannery sludge. The results demonstrated that chromium in tannery sludge can be efficiently leached by the indigenous A. thiooxidans.

  19. Biosorption potency of Aspergillus niger for removal of chromium (VI).

    Science.gov (United States)

    Srivastava, Shaili; Thakur, Indu Shekhar

    2006-09-01

    Aspergillus niger isolated from soil and effluent of leather tanning mills had higher activity to remove chromium. The potency of Aspergillus niger was evaluated in shake flask culture by absorption of chromium at pH 6 and temperature 30 degrees C. The results of the study indicated removal of more than 75% chromium by Aspergillus niger determined by diphenylcarbazide colorimetric assay and atomic absorption spectrophotometry after 7 days. Study of microbial Cr(VI) reduction and identification of reduction intermediates has been hindered by the lack of analytical techniques that can identify the oxidation state with subcellular spatial resolution. Therefore, removal of chromium was further substantiated by transmission electron microscopy (TEM), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDX), which indicated an accumulation of chromium in the fungal mycelium. PMID:16874547

  20. Natural occurrence of hexavalent chromium in a sedimentary aquifer in Urânia, State of São Paulo, Brazil

    Directory of Open Access Journals (Sweden)

    Christine Bourotte

    2009-06-01

    Full Text Available Anomalous concentrations of hexavalent chromium have been detected in ground-water of the Adamantina Aquifer inat least 54 municipalities located in the northwestern region of the State of São Paulo, southeast Brazil, occasionallyexceeding the permitted limit for human consumption (0.05 mg.L-1. An investigation was conducted in the municipality of Urânia, where the highest concentrations of chromium were detected regionally. It was defined that the originof this contamination is natural, since high concentrations of chromium were detected in aquifer sandstones (averageof 221 ppm and also in pyroxenes (6000 ppm, one of the main heavy minerals found in the sediments. Besides, noother possible diffuse or point sources of contamination were observed in the study area. Stratification of ground-waterquality was observed and the highest concentrations of Cr6+ were detected at the base of the aquifer (0.12 mg.L-1,where ground-water shows elevated values for redox potential (472.5 mV and pH (8.61. The origin of Cr6+ in water may be associated with the weathering of pyroxene (augite, followed by the oxidation of Cr3+ by manganese oxides. The highest concentrations of Cr6+ are probably related to desorption reactions, due to the anomalous alkaline pHfound in ground-water at the base of the aquifer.Concentrações anômalas de cromo hexavalente foram detectadas em águas subterrâneas do Aqüífero Adamantina em pelo menos 54 municipalidades localizadas na região noroeste do Estado de São Paulo, sudeste do Brasil, algumas vezes ultrapassando o limite máximo permitido para consumo humano (0,05 mg.L-1. Um estudo foi realizado no município de Urânia, onde as mais elevadas concentrações de cromo da região foram detectadas. A origem da contaminação foi definida como natural, pois foram detectadas concentrações de cromonos arenitos do aqüífero (média 221 ppm e em piroxênios (6000 ppm, um dos principais minerais pesados encontrados nos sedimentos

  1. Selenium protection from cadmium and chromium poisoning

    International Nuclear Information System (INIS)

    The interaction of selenium with cadmium and chromium was studied in 168 chicken-broilers (DWCxWR) divided into four equal groups. Eight-week old control animals received an intravenous dose of /sup 115m/Cd Chloride 370 KBq/Kg (Group I), or 51Cr Chloride 370 KBq/Kg (Group II). The kinetics of these isotopes were studied by scintillation spectrometry (NaI/TI) carried out for whole blood, plasma, plasma proteins, urine, feces and homogenates of all organs at various time intervals. Animals in Groups III and IV received eight subcutaneous doses of sodium selenate (5ug) at 8-week intervals prior to /sup 115m/Cd or 51Cr. The kinetics of these elements were studied as in the previous two groups. It was found that selenium affected those kinetics in two ways: (a) by increasing the excretion of Cd by 11 +/- 3% (P < 0.001) and that of Cr by 7 +/- 1% (P < 0.001); and (b) by favoring redistribution of those elements, with significant (P < 0.001) reductions in liver, endocrine glands and kidney and increases (P < 0.01) in bone. The study suggests that selenium protects the animals' vital organs from environmental pollutants, such as cadmium and chromium

  2. Hexavalent chromium reduction with scrap iron in continuous-flow system. Part 2: Effect of scrap iron shape and size.

    Science.gov (United States)

    Gheju, M; Balcu, I

    2010-10-15

    Hexavalent chromium reduction with scrap iron has the advantage that two wastes are treated simultaneously. The reduction of hexavalent chromium by scrap iron was investigated in continuous system, using as reducing agent the following scrap iron shapes and sizes: (1) spiral fibers, (2) shavings, and (3) powder. The shape and size of scrap iron were found to have a significant influence on chromium and iron species concentration in column effluent, on column effluent pH and on Cr(VI) reduction mechanism. While for large scrap iron particles (spiral fibers) homogeneous reduction is the dominant Cr(VI) reduction process, for small scrap iron particles (powder) heterogeneous reduction appears to be the dominant reaction contributing to Cr(VI) reduction. All three shapes and sizes investigated in this work have both advantages and disadvantages. If found in sufficient quantities, scrap iron powder seem to be the optimum shape and size for the continuous reduction of Cr(VI), due to the following advantages: (1) the greatest reduction capacity, (2) the most important pH increase in column effluent (up to 6.3), (3) no chromium was detected in the column effluent during the first 60 h of the experiment, and (4) the lowest steady-state Cr(VI) concentration observed in column effluent (3.7 mg/L). But, despite of a lower reduction capacity in comparison with powder particles, spiral fibers and shavings have the advantage to result in large quantities from the mechanic processing of steel.

  3. Kinetics of hexavalent chromium reduction by iron metal

    Institute of Scientific and Technical Information of China (English)

    Huijing QIAN; Yanjun WU; Yong LIU; Xinhua XU

    2008-01-01

    The kinetics of Cr(Ⅵ) reduction to Cr(Ⅲ) by metallic iron (Fe0) was studied in batch reactors for a range of reactant concentrations, pH and temperatures. Nearly 86.8% removal efficiency for Cr(Ⅵ) was achieved when Fe0 concentration was 6 g/L (using commercial iron powder (200 mesh) I n 120 min). The reduction ofhexavalent chro-mium took place on the surface of the iron particles following pseudo-first order kinetics. The rate of Cr(Ⅵ) reduction increased with increasing Fe0 addition and temperature but inversely with initial pH. The pseudo-first-order rate coeffi-cients (kobs) were determined as 0.0024, 0.010, 0.0268 and 0.062 8 min-1 when iron powder dosages were 2, 6, 10 and 14 g/L at 25℃ and pH 5.5, respectively. According to the Arrehenius equation, the apparent activation energy of 26.5 kJ/mol and pre-exponential factor of 3 330 min-1 were obtained at the temperature range of 288-308 K. Different Fe0 types were compared in this study. The reactivity was in the order starch-stabilized Fe0 nanoparticlesFe0 nano-particlesFe0 powderFe0 filings. Electrochemical analysis of the reaction process showed that Cr(Ⅲ) and Fe(Ⅲ) hydroxides should be the dominant final products.

  4. Standard Specification for Pressure Consolidated Powder Metallurgy Iron-Nickel-Chromium-Molybdenum (UNS N08367), Nickel-Chromium-Molybdenum-Columbium (Nb) (UNS N06625), Nickel-Chromium-Iron Alloys (UNS N06600 and N06690), and Nickel-Chromium-Iron-Columbium-Molybdenum (UNS N07718) Alloy Pipe Flanges, Fittings, Valves, and Parts

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2015-01-01

    Standard Specification for Pressure Consolidated Powder Metallurgy Iron-Nickel-Chromium-Molybdenum (UNS N08367), Nickel-Chromium-Molybdenum-Columbium (Nb) (UNS N06625), Nickel-Chromium-Iron Alloys (UNS N06600 and N06690), and Nickel-Chromium-Iron-Columbium-Molybdenum (UNS N07718) Alloy Pipe Flanges, Fittings, Valves, and Parts

  5. 75 FR 65067 - National Emission Standards for Hazardous Air Pollutant Emissions: Hard and Decorative Chromium...

    Science.gov (United States)

    2010-10-21

    ... Decorative Chromium Electroplating and Chromium Anodizing Tanks; Group I Polymers and Resins; Marine Tank...: Hard and Decorative Chromium Electroplating and Chromium Anodizing Tanks; Group I Polymers and Resins... Tanks. Group I Polymers and Resins Production.. Scott Throwe, (202) 564-7013,...

  6. Chromium-induced membrane damage: protective role of ascorbic acid

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Importance of chromium as environmental toxicant is largely due to impact on the body to produce cellular toxicity. The impact of chromium and their supplementation with ascorbic acid was studied on plasma membrane of liver and kidney in male Wistar rats (80 - 100gbody weight). It has been observed that the intoxication with chromium ( i. p. ) at the dose of 0.8 mg/100g body weight per day for a period of 28 days causes significant increase in the level of cholesterol and decrease in the level of phospbolipid of both liver and kidney. The alkaline pbosphatase, total ATPase and Na + -K + -ATPase activities were significantly decreased in both liver and kidney after chromium treatment,except total ATPase activity of kidney. It is suggested that chromium exposure at the present dose and duration induce for the alterations of structure and function of both liver and kidney plasma membrane. Ascorbic acid ( i.p. at the dose of 0.5 mg,/100g body weight per day for period of 28 days) supplementation can reduce these structural changes in the plasma membrane of liver and kidney. But the functional changes can not be completely replenished by the ascorbic acid supplementation in response to chromium exposure. So it is also suggested that ascorbic acid (nutritional antioxidant) is useful free radical scavenger to restrain the chromium-induced membrane damage.

  7. Bioavailability of a potato chromium complex to the laboratory rat

    International Nuclear Information System (INIS)

    Research objectives were to study the effect of food source, preparation method and chemical form on bioavailability of chromium. Chromium concentration in potatoes was determined and tubers labeled either intrinsically or extrinsically with radioactive chromate. A labeled chromium complexes was isolated from preparations of raw, baked or fried potatoes and chromatographed on gel permeation media. Availability of the potato chromium complex to the rat was examined in three feeding studies. Animals were dosed with radioactive extrinsically or intrinsically labeled potato extract or with chromate. A labeled chromium complex was isolated from gastrointestinal contents of rats and chromatographed. Potato pulp and peel contained 1.63 and 2.70 μg Cr/g tissue respectively. True and apparent absorption from extrinsically labeled feedings were 33.4 +/- 4.7 and 29.8 +/- 11.2% respectively, and no differences existed between absorption from raw and cooked potatoes. Absorption from the extrinsic labeled potatoes differed significantly from absorption of inorganic chromatium. Apparent absorption of raw (11.1 +/- 7.9%) and cooked (-0.7 +/- 2.8%) intrinsically labeled feedings differed significantly. Absorption of inorganic chromium was 17.8% (true) and 11.5% (apparent). Examination of the chromium complex isolated from gastrointestinal tract contents showed enlargement of the complex in the stomach after consumption

  8. Stabilization of chromium salt in ordinary portland cement

    Indian Academy of Sciences (India)

    Damir Barbir; Pero Dabić; Petar Krolo

    2012-12-01

    Ordinary Portland cement (OPC) samples containing the chromium salt have been investigated using differential microcalorimetry, conductometry and Fourier transform infrared spectroscopic analysis. The effect of chromium on OPC hydration was evaluated by continuous observing of early hydration. The microcalorimetrical results show that with increasing the share of chromium salt, heat maximums assume lower values and the occurrence of the maximum registered in the earlier hydration times. Conductometrical measurements show that with increasing addition of chromium salt, curve did not show any specific shape, immediate drop in specific conductivity is noticed and the maximum is reached earlier. This coincides with microcalorimetrical results. It can be concluded that the addition of chromium does not affect the mechanism of the hydration process, but it does affect the kinetic parameters and dynamics of the cement hydration process. It was found that chromium salt addition to the cement–water system is acceptable up to 2 wt.%. According to standard EN 196-3 for OPC, the beginning of binding time should occur after 60 minutes. Increased amount of chromium over 2 wt.% significantly accelerate the beginning of binding time and for the system it is not acceptable.

  9. Chromium speciation in rainwater: temporal variability and atmospheric deposition

    Energy Technology Data Exchange (ETDEWEB)

    Kieber, R.J.; Willey, J.D.; Zvalaren, S.D. [University of North Carolina at Wilmington, Wilmington, NC (United States). Dept. of Chemistry

    2002-12-15

    Chromium is released into the atmosphere by a variety of anthropogenic activities which include steel manufacturing, leather tanning, wood presentation and fossil fuel combustion. The concentrations of the various chromium species were determined in 89 rainwater samples collected in Wilmington, NC from October 1, 1999 to December 31, 2001. Volume weighted annual average concentrations of Cr{sub total}, particulate Cr, Cr(III)(aq), and Cr(VI)(aq) were 4.6, 2.2, 0.8 and 1.2 nM, respectively. There was distinct seasonal and diurnal variability in the concentrations of the various chromium species. Chromium emissions to the global atmosphere by both natural and anthropogenic sources are estimated to be 2.2 x 10{sup 9} mol/yr. Using rainwater concentration data along with other published rainwater Cr concentrations and an estimate for total global annual rain, the total global flux of chromium removed from the atmosphere via wet deposition is 2.1 x 10{sup 9} mol/yr. This represents complete removal of Cr and indicates that essentially all chromium released into the global atmosphere is removed via rain. About half this chromium is dissolved with roughly equal concentrations of toxic Cr(VI) and relatively harmless Cr(III) species. 48 refs., 4 figs., 3 tabs.

  10. Workshop on effects of chromium coating on Nb3Sn superconductor strand: Proceedings

    International Nuclear Information System (INIS)

    This report discusses the following topics: Chromium coating on superconductor strand -- an overview; technology of chromium plating; comparison of wires plated by different platers; search for chromium in copper; strand manufactures' presentations; chromium plating at the Lawrence Livermore National Laboratory; a first look at a chromium plating process development project tailored for T.P.X. and I.T.E.R. strand; and influence of chromium diffusion and related phenomena on the reference ratios of bare and chromium plated Nb3Sn strand

  11. Workshop on effects of chromium coating on Nb{sub 3}Sn superconductor strand: Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    1994-04-12

    This report discusses the following topics: Chromium coating on superconductor strand -- an overview; technology of chromium plating; comparison of wires plated by different platers; search for chromium in copper; strand manufactures` presentations; chromium plating at the Lawrence Livermore National Laboratory; a first look at a chromium plating process development project tailored for T.P.X. and I.T.E.R. strand; and influence of chromium diffusion and related phenomena on the reference ratios of bare and chromium plated Nb{sub 3}Sn strand.

  12. Fertilizers and Mixed Crop Cultivation of Chromium Tolerant and Sensitive Plants under Chromium Toxicity

    OpenAIRE

    B. Dheeba; Sampathkumar, P; Kannan, K.

    2015-01-01

    Zea mays (maize) and Vigna radiata (green gram) are found to be the chromium (Cr) tolerant and sensitive plants, respectively. In the present paper, we investigate the reduction of the toxicity of Cr in the sensitive plants by the mixed crop cultivation in the field using various amendments. Further, the potassium dichromate was used as the source of hexavalent Cr. The results indicated that Cr adversely affects both the growth and yield of plants. The soil properties vary with Cr and differe...

  13. Wet skins tanning with chromium in dense CO{sub 2} under pressure; Tannage au chrome de peaux humides en CO{sub 2} dense sous pression

    Energy Technology Data Exchange (ETDEWEB)

    Saldinari, L. [Tanneries Roux SA, 26 - Romans Sur Isere (France)]|[Tanneries du Puy (France)]|[Tanneries d' Annonay, 07 (France); Dutel, Ch. [Societe ATC (France); Perre, Ch. [CEA Centre de Pierrelatte (DCC/DTE/SLC), 26 (France)

    2000-07-01

    An ancestral gesture steadily improved through the centuries, the transformation of skins into leather includes several stages of which the principal one is tanning. Today, 90 % of the world's leather products are tanned with chromium. However, this stage is an environmental liability, and reducing the volume and chromium content of the waste has become a major issue. A first study on skin degreasing by dense CO{sub 2} helped sharply reduce the volume of the fatty effluents. To replace water by dense CO{sub 2} as the tanning medium was the logical next step. The present study was carried out in cooperation with three tanneries in the Rhone-Alpes-Auvergne area of France and a manufacturer of tanning materials. The difficulty of the study was the chemically opposed character of the two media involved. CO{sub 2} is a non-polar and lipophilic solvent while inorganic chromium is insoluble. The water present in the treated skin is a polar and ionic reaction medium and one of the reagents in tanning chemistry. The mixture of these two partially miscible compounds gives a pH 3 by carbonic acid formation. Tanning is based on the reactivity of collagen, the main component of the skin, with hydroxylated complexes of chromium. Collagen is a protein containing some chemical functions, amines (R-NH{sub 2}) and carboxylic (R-COOH) for example. These functions impart an amphoteric character to the compound. The WERNER theory of complex salts explains the formation of hydroxylated complexes of chromium and their fixing on the carboxylic functions of collagen by oxolation. pH is the key parameter in tanning. The success of the process demands chromium impregnation without fixing it at a pH lower than 5, and then to fix it by increasing the pH. This opened two alternatives for transferring chromium in the skin: solubilize chromium in CO{sub 2} via soluble organometallic complexes; or put the chromium salt into suspension without solubilizing it. The best results were obtained

  14. Delta(54) flavor phenomenology and strings

    CERN Document Server

    Carballo-Perez, Brenda; Ramos-Sanchez, Saul

    2016-01-01

    Delta(54) can serve as a flavor symmetry in particle physics, but remains almost unexplored. We show that in a classification of semi-realistic Z3xZ3 heterotic string orbifolds, Delta(54) turns out to be the most natural flavor symmetry, providing additional motivation for its study. We revisit its phenomenological potential from a low-energy perspective and subject to the constraints of string models. We find that Delta(54) arising from heterotic orbifolds leads to the Gatto-Sartori-Tonin relation for quarks and charged-leptons. Additionally, in the neutrino sector, it generically leads to a normal hierarchy for neutrino masses and a correlation between the reactor and the atmospheric mixing angles, the latter taking values in the second octant and being compatible at three sigmas with experimental data.

  15. Analytical investigation of chromium and zinc in sweet, sour and bitter tasting fruits, vegetables and medicinal plants

    Directory of Open Access Journals (Sweden)

    Syed Ahmad Tirmizi

    2007-01-01

    Full Text Available Sweet, sour and bitter tasting fruits, vegetables and medicinal plants are an important component of human diet. The role of chromium and zinc in carbohydrate metabolism for control of diabetes is highlighted in selected commodities. Average levels of chromium and zinc in sweet taste were 0.69 ± 0.48 mg kg-1 and 4.81 ± 4.31 mg kg-1 respectively with correlation of 0.545, while in sour taste the values were 22.5 ± 22.0 mg kg-1 and 24.5 ± 11.8 mg kg-1 respectively with the correlation of 0.239 and in bitter taste, 0.61 ± 0.33 mg kg-1 and 4.70 ± 3.54 mg kg-1 respectively with correlation of 0.343. Overall, sour tasting commodities were found higher in levels of chromium and zinc and are recommended as food supplement for diabeties. None of these species contain metals above the toxic level.

  16. Microbial Diversity of Chromium-Contaminated Soils and Characterization of Six Chromium-Removing Bacteria

    Science.gov (United States)

    He, Zhiguo; Hu, Yuting; Yin, Zhen; Hu, Yuehua; Zhong, Hui

    2016-06-01

    Three soil samples obtained from different sites adjacent to a chromium slag heap in a steel alloy factory were taken to examine the effect of chromium contamination on soil bacterial diversity as determined by construction of 16S rDNA clone libraries and sequencing of selected clones based on restriction fragment length polymorphism (RFLP) analysis. Results revealed that Betaproteobacteria, Gammaproteobacteria, Firmicutes, and Alphaproteobacteria occurred in all three soil samples, although the three samples differed in their total diversity. Sample 1 had the highest microbial diversity covering 12 different classes, while Sample 3 had the lowest microbial diversity. Strains of six different species were successfully isolated, one of which was identified as Zobellella denitrificans. To our knowledge, this is the first report of a strain belonging to the genus Zobellella able to resist and reduce chromium. Among all isolates studied, Bacillus odysseyi YH2 exhibited the highest Cr(VI)-reducing capability, with a total removal of 23.5 % of an initial Cr(VI) concentration of 350 mg L-1.

  17. A REVIEW OF BIOSORPTION OF CHROMIUM IONS BY MICROORGANISMS

    Directory of Open Access Journals (Sweden)

    Inga Zinicovscaia

    2012-12-01

    Full Text Available Due to its widespread industrial use, chromium has become a serious pollutant in diverse environmental settings. The main source of chromium pollution including the Republic o Moldova is industry. It is a great need to develop new eco-friendly methods of chromium removal. Biosorption of heavy metals is a most promising technology involved in the removal of toxic metals from industrial waste streams and natural waters. This article is an extended abstract of a communication presented at the Conference Ecological Chemistry 2012

  18. Iron(II modified natural zeolites for hexavalent chromium removal from contaminated water

    Directory of Open Access Journals (Sweden)

    Lofù Antonio

    2016-03-01

    Full Text Available Three different types of Fe(II-modified natural zeolites were tested as supports in continuous-flow columns for the treatment of Cr(VI contaminated water. The natural zeolites chosen as support were commercially available Zeosand (80% clinoptilolite, ATZ (79% phillipsite/chabazite, and ZS-55RW (90% Chabazite. All the examined modified zeolites turned out active for hexavalent chromium abatement, lowering its concentration below the European regulation level, even at relatively high flow rates (40 mL/h, linear velocity 15 cm/h. Zeosand, having a broader pH range of stability, was found to be the best one in terms of both Fe(II uptake (0.54 wt% and Cr removal (90 mg Cr/Kg zeolite.

  19. Cosmic ray half life of 54Mn

    International Nuclear Information System (INIS)

    A search for the β+ decay of 54Mn has established an upper limit of 4.4 x 10-8 for this branching ratio, and a lower limit of 13.3 for the log ft value for this second forbidden unique transition. Assuming that the β- decay branch has the same log ft value, then its partial half life must be greater than 4 x 104 years. Experiments to directly measure the β- decay rate of 54Mn are now in progress. 6 refs., 2 figs

  20. Thermal incorporation behavior during the reduction and stabilization of chromium wastes

    OpenAIRE

    Yang, Jun; 楊駿

    2015-01-01

    The possibility of employing periclase to stabilize chromium in chromium wastes into spinel-based ceramics through thermal method was investigated by heating mixture of simulated chromium waste and magnesium oxide. Different types of magnesium oxide precursors were introduced to incorporate chromium oxide into magnesiochromite (MgCr2O4) ranging from 550 ºC to 1350 ºC. Magnesium oxide precursors of both types can effectively incorporate chromium oxide but via different mechanisms. Three main f...

  1. Effects of Supplemental Dietary Chromium on Yield and Nutrient Digestibility of Laying Hens Under Low Temperature

    OpenAIRE

    ŞAHİN, Kazım; ERTAŞ, O. Nihat; GÜLER, Talat; ÇİFTÇİ, Mehmet

    2001-01-01

    This study was conducted to determine the effects of chromium picolinate (CrPi) added into diet containing 710.3 ppb chromium on yield and nutrient digestibility of laying hens at low temperature. Forty-six-week-old laying hens were randomly assigned to four groups of 30 hens per group. Treatment groups were fed different supplemental dietary chromium levels. Thus, hens were fed diets with no supplemental chromium (Control Group), 100 ppb of supplemental chromium (100 Group), 200 ppb of s...

  2. The fate of chromium during tropical weathering

    DEFF Research Database (Denmark)

    Berger, Alfons; Frei, Robert

    2014-01-01

    We performed a mineral, geochemical and Cr–Sr–Pb isotope study on a laterite profile developed on ca. 540 Ma old tonalitic bedrock in Madagascar with special emphasis on the behavior of chromium during tropical weathering. The observed strong depletions of Ca, Si, and P, and enrichment of Fe and Al...... of the soil profile relative to stage one altered saprolite. This gain in Cr is accompanied by decreasing δ53Cr values and can be explained by partial immobilization (possibly by adsorption/coprecipitation on/with Fe-oxy-hydroxides) of mobile Cr(III) during upward transport in the weathering profile....... The negatively fractionated δ53Cr values measured in the weathering profile relative to the unaltered tonalitic bedrock characterized by a high temperature magmatic inventory Cr isotope signature are consistent with loss of a positively fractionated Cr(VI) pool formed during weathering. The predicted existence...

  3. Evaluation of chromium in red blood cells as an indicator of exposure to hexavalent chromium: An in vitro study.

    Science.gov (United States)

    Devoy, Jérôme; Géhin, Antoine; Müller, Samuel; Melczer, Mathieu; Remy, Aurélie; Antoine, Guillaume; Sponne, Isabelle

    2016-07-25

    Chromium(VI) compounds are classified as carcinogenic to humans. Whereas chromium measurements in urine and whole blood (i.e., including plasma) are indicative of recent exposure, chromium in red blood cells (RBC) is attributable specifically to Cr(VI) exposure. Before recommending Cr in RBC as a biological indicator of Cr(VI) exposure, in-vitro studies must be undertaken to assess its reliability. The present study examines the relationship between the chromium added to a blood sample and that subsequently found in the RBC. After incubation of total blood with chromium, RBC were isolated, counted and their viability assessed. Direct analysis of chromium in RBC was conducted using Atomic Absorption Spectrometry. Hexavalent, but not trivalent Cr, was seen to accumulate in the RBC and we found a strong correlation between the Cr(VI) concentration added to a blood sample and the amount of Cr in RBC. This relationship appears to be independent of the chemical properties of the human blood samples (e.g., different blood donors or different reducing capacities). Even though in-vivo studies are still needed to integrate our understanding of Cr(VI) toxicokinetics, our findings reinforce the idea that a single determination of the chromium concentration in RBC would enable biomonitoring of critical cases of Cr(VI) exposure. PMID:27178267

  4. Chromium accumulation, microorganism population and enzyme activities in soils around chromium-containing slag heap of steel alloy factory

    Institute of Scientific and Technical Information of China (English)

    HUANG Shun-hong; PENG Bing; YANG Zhi-hui; CHAI Li-yuan; ZHOU Li-cheng

    2009-01-01

    The environmental risk of chromium pollution is pronounced in soils adjacent to chromate industry. It is important to investigate the functioning of soil microorganisms in ecosystems exposed to long-term contamination by chromium. 45 soil samples obtained from different places of the slag heap in a steel alloy factory were analyzed for chromium contamination level and its effect on soil microorganisms and enzyme activities. The results show that the average concentrations of total Cr in the soil under the slag heap, adjacent to the slag heap and outside the factory exceed the threshold of Secondary Environmental Quality Standard for Soil in China by 354%, 540% and 184%, respectively, and are 15, 21 and 9 times higher than the local background value, respectively. Elevated chromium loadings result in changes in the activity of the soil microbe, as indicated by the negative correlations between soil microbial population and chromium contents. Dehydrogenase activity is greatly depressed by chromium in the soil. The results imply that dehydrogenase activity can be used as an indicator for the chromium pollution level in the area of the steel alloy factory.

  5. Accurate quantification of total chromium and its speciation form Cr(VI) in water by ICP-DRC-IDMS and HPLC/ICP-DRC-IDMS.

    Science.gov (United States)

    Markiewicz, Barbara; Komorowicz, Izabela; Barałkiewicz, Danuta

    2016-05-15

    Two analytical procedures have been developed for the determination of total chromium (TCr) and its highly toxic species, i.e. Cr(VI) in water samples using the following methods: inductively coupled plasma dynamic reaction cell isotope dilution mass spectrometry (ICP-DRC-IDMS) and high performance liquid chromatography inductively coupled plasma dynamic reaction cell isotope dilution mass spectrometry (HPLC/ICP-DRC-IDMS). Spectral interferences, predominantly occurring in chromium determination, were removed using a dynamic reaction cell (DRC). The presented procedures facilitate the quantification of trace amounts - below 1 µg L(-1) of TCr and individual Cr species - in various water matrices including drinking water and still bottled water with different mineral composition. Special attention has been paid to the adequate preparation of isotopically enriched (53)Cr(VI) standard solution in order to avoid artifacts in chromium speciation. Both procedures were fully validated as well as establishing the traceability and estimation of the uncertainty of measurement were carried out. Application of all of the above mentioned elements and of the isotope dilution technique, which provides the highest quality of metrological traceability, allowed to obtain reliable and high quality results of chromium determination in water samples. Additionally, the comparison of two methods: HPLC/ICP-DRC-MS and HPLC/ICP-DRC-IDMS for Cr(VI) determination, was submitted basing on the validation parameters. As a result, the lower values for these parameters were obtained using the second method. PMID:26992546

  6. Effects of Chromium(VI) and Chromium(III) on Desulfovibrio vulgaris Cells

    Energy Technology Data Exchange (ETDEWEB)

    M.E. Clark; A. Klonowska; S.B. Thieman; B. Giles; J.D. Wall; and M.W. Fields

    2007-04-19

    Desulfovibrio vulgaris ATCC 29579 is a well studied sulfate reducer that has known capabilities of reducing heavy metals and radionuclides, like chromium and uranium. Cultures grown in a defined medium (i.e. LS4D) had a lag period of approximately 40 h when exposed to 50 μMof Cr(VI). Substrate analysis revealed that although chromium is reduced within the first 5 h, growth does not resume for another 35 h. During this time, small amounts of lactate are still utilized but the reduction of sulfate does not occur. Sulfate reduction occurs concurrently with the accumulation of acetate approximately 40 h after inoculation, when growth resumes. Similar amounts of hydrogen are produced during this time compared to hydrogen production by cells not exposed to Cr(VI); therefore an accumulation of hydrogen cannot account for the utilization of lactate. There is a significant decrease in the carbohydrate to protein ratio at approximately 25 h, and this result indicated that lactate is not converted to glycogen. Most probable number analysis indicated that cell viability decreased steadily after inoculation and reached approximately 6 x 104 cells/ml 20 h post-chromium exposure. Regeneration of reducing conditions during chromium exposure does not induce growth and in fact may make the growth conditions even more unfavorable. This result suggested that an increase in Eh was not solely responsible for the decline in viability. Cell pellets collected 10 h after chromium-exposure were unable to resume growth when suspended into fresh medium. Supernatants from these pellets were able to support cell growth upon re- inoculation. D. vulgaris cells treated with a non-dose dependent addition of ascorbate at the same time of Cr(VI) addition did not enter a lag period. Ascorbate added 3 h post-Cr(VI) exposure did not prevent the growth lag. These results indicated that Desulfovibrio utilized lactate to reduce Cr(VI) without the reduction of sulfate, that the decline in cell viability and

  7. Effect of the Detoxification on the Shrinkage Temperature and pH of Chromium Leather Waste, Another Promising Way for the Tannery Pollution

    Directory of Open Access Journals (Sweden)

    A. Malek

    2008-01-01

    Full Text Available The leather tannery industry produces a significant amount of solid chromium waste. Environmental concerns and escalating landfill costs are becoming increasingly serious problems to the leather industry and alternative disposal methods are needed. This research describes the possibility of decrease of the shrinkage temperature and to increase the pH value of leather waste by detoxification treatment with use of tartrate potassium. Through this investigation, we have established that is more possible to reduce the shrinkage temperature and neutralizing the acidity of this waste without his degradation or digestion and with decreasing of his chromium content about 95%. The use of reaction time of 72 h generates the optimal decreasing of the shrinkage temperature of waste leather about 42°C close to the one of hide at native state (before tanning process which reveal another ecological and simple way for the treatment of the chromium containing leather waste.

  8. Study of structural transformations occuring in low carbon chromium-molybdenum ferritic steels: influence of small additions of vanadium and niobium

    International Nuclear Information System (INIS)

    This study has been carried out on several low carbon chromium-molybdenum ferritic steels: 2,25%0C to 13000C. In the case of alloys with high chromium concentration and additions of vanadium and niobium, the austenitic transformation is partial, and heat treating at higher temperatures results in increased delta transformation, a phenomenon which is accentuated by an important sensitivity to decarburization. Austenitic transformation during cooling leads to two types of CCT curves according to chromium content. Variations in chemical composition and austenitizing temperature significantly modify these diagrams, in particular those of the niobium stabilized steels. The morphology of the structures produced are very diverse, without important presence of residual austenite. The tempering behaviour in anisothermal and isothermal conditions was followed, and the temperature range limits within which precipitation reactions occur were determined in view of characterizing for each alloy the different types of precipitates formed and their influence on the mechanical resistance of the alloy after tempering

  9. Scientific Opinion on ChromoPrecise® cellular bound chromium yeast added for nutritional purposes as a source of chromium in food supplements and the bioavailability of chromium from this source

    Directory of Open Access Journals (Sweden)

    EFSA Panel on Food Additives and Nutrient Sources added to Food (ANS

    2012-11-01

    Full Text Available The Panel on Food Additives and Nutrient Sources added to Food (ANS provides a scientific opinion re-evaluating the safety of ChromoPrecise® cellular bound chromium yeast added for nutritional purposes as a source of chromium in food supplements and the bioavailability of chromium from this source. ChromoPrecise® is a yeast preparation with an enriched trivalent chromium content, obtained by culture of Saccharomyces cerevisiae in the presence of chromium chloride. A daily intake of 100 µg chromium(III. There are limited data on the nature and identity of the organic chromium(III compounds contained in chromium-enriched yeast and on their toxicokinetic and toxicodynamic behaviour in the body. Overall, the Panel concluded that the bioavailability in man of chromium from chromium-enriched yeast is potentially up to approximately ten times higher than that of chromium from chromium chloride. A NOAEL of 2500 mg/kg bw/day ChromoPrecise® was identified in a 90-day feeding study in rats; no evidence of adverse effects of chromium yeasts were reported in other animal studies investigating the effects of dietary supplementation with chromium yeast. ChromoPrecise® chromium yeast was non-genotoxic in a range of in vitro genotoxicity studies. Although no information was available on the chronic toxicity, carcinogenicity or reproductive toxicity of ChromoPrecise® chromium yeast, the ANS Panel has previously concluded that trivalent chromium is not carcinogenic, and limited data on other chromium yeasts provide no evidence of an effect on reproductive endpoints. No adverse effects have been reported in clinical efficacy trials with chromium yeasts. The Panel concluded that the use of ChromoPrecise® chromium yeast in food supplements is not of concern, despite the lack of data on the nature and identity of the organic chromium(III compounds contained in the product, provided that the intake does not exceed 250 μg/day, as recommended by the WHO.

  10. 17 CFR 200.54 - Constitutional obligations.

    Science.gov (United States)

    2010-04-01

    ... 17 Commodity and Securities Exchanges 2 2010-04-01 2010-04-01 false Constitutional obligations... ORGANIZATION; CONDUCT AND ETHICS; AND INFORMATION AND REQUESTS Canons of Ethics § 200.54 Constitutional... against any infringement of the constitutional rights, privileges, or immunities of those who are...

  11. 47 CFR 54.401 - Lifeline defined.

    Science.gov (United States)

    2010-10-01

    ... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES (CONTINUED) UNIVERSAL SERVICE Universal Service Support for Low-Income Consumers § 54.401 Lifeline defined. (a) As used in this...-income consumers; (2) For which qualifying low-income consumers pay reduced charges as a result...

  12. 7 CFR 1786.54 - Eligibility criteria.

    Science.gov (United States)

    2010-01-01

    ... AGRICULTURE (CONTINUED) PREPAYMENT OF RUS GUARANTEED AND INSURED LOANS TO ELECTRIC AND TELEPHONE BORROWERS Special Discounted Prepayments on RUS Direct/Insured Loans § 1786.54 Eligibility criteria. To be eligible to prepay RUS Notes at the Discounted Present Value a borrower must comply with the...

  13. 40 CFR 79.54 - Tier 3.

    Science.gov (United States)

    2010-07-01

    ... testing may be indicated if the results of the In vivo Micronucleus Assay, required under § 79.64, the In... FUELS AND FUEL ADDITIVES Testing Requirements for Registration § 79.54 Tier 3. (a) General Criteria for Requiring Tier 3 Testing. (1) Tier 3 testing shall be required of a manufacturer or group of...

  14. STS-54 Crew Arrival for TCDT

    Science.gov (United States)

    1992-01-01

    Footage shows the crew of STS-54, Commander John H. Casper, Pilot Donald R. McMonagle, and Mission Specialists Mario Runco, Jr., Gregory J. Harbaugh, and Susan J. Helms landing and emerging from several T-38 aircraft during the Terminal Countdown and Demonstration Test (TCDT). Commander Casper introduces the crew and they each make a brief statement about the mission.

  15. 7 CFR 54.25 - Superseded certificates.

    Science.gov (United States)

    2010-01-01

    ... null and void and shall not thereafter be deemed to show the class, grade, other quality, or compliance... AGRICULTURAL MARKETING ACT OF 1946 AND THE EGG PRODUCTS INSPECTION ACT (CONTINUED) MEATS, PREPARED MEATS, AND MEAT PRODUCTS (GRADING, CERTIFICATION, AND STANDARDS) Regulations Appeal Service § 54.25...

  16. 7 CFR 54.24 - Appeal certificates.

    Science.gov (United States)

    2010-01-01

    ... certificate and stating the class, grade, other quality, or compliance of the products as shown by the appeal... AGRICULTURAL MARKETING ACT OF 1946 AND THE EGG PRODUCTS INSPECTION ACT (CONTINUED) MEATS, PREPARED MEATS, AND MEAT PRODUCTS (GRADING, CERTIFICATION, AND STANDARDS) Regulations Appeal Service § 54.24...

  17. 47 CFR 54.508 - Technology plans.

    Science.gov (United States)

    2010-10-01

    ... that the Department of Education adopts future technology plan requirements that require one or more of... covered by the future Department of Education technology plan requirements. (c) Timing of certification... 47 Telecommunication 3 2010-10-01 2010-10-01 false Technology plans. 54.508 Section...

  18. Contingency plans for chromium utilization. Publication NMAB-335

    International Nuclear Information System (INIS)

    The United States depends entirely on foreign sources for the critical material, chromium, making it very vulnerable to supply disruptions. This vulnerability results because chromium is essential for the fabrication of corrosion-resisting steels and high-temperature, oxidation-resisting alloys in applications that are vital to the nation's technological well-being; because no substitutes are known for these materials in those applications; and because the known, substantial deposits of chromite ore are only in a few geographical locations that could become inaccessible to the United States as a result of political actions. The effectiveness of programs such as stockpiling, conservation, and research and development for substitutes to reduce the impact of disruption of imports of chromite and ferrochromium are discussed. Alternatives for decreasing chromium consumption also are identified for chromium-containing materials in the areas of design, processing, and substitution

  19. Fabrication of high rate chromium getter sources for fusion applications

    International Nuclear Information System (INIS)

    Design and fabrication techniques are described for the manufacture of large-capacity chromium getter sources, analogous to the commercially available titanium getter source known as Ti-Ball, manufactured by Varian Associates

  20. IRIS Toxicological Review of Hexavalent Chromium (Peer Review Plan)

    Science.gov (United States)

    EPA is conducting a peer review of the scientific basis supporting the human health hazard and dose-response assessment of hexavalent chromium that will appear on the Integrated Risk Information System (IRIS) database.

  1. Chromium and Polyphenols from Cinnamon and Insulin Sensitivity

    Science.gov (United States)

    Factors that improve insulin sensitivity usually lead to improvements in risk factors associated with the metabolic syndrome, diabetes, and cardiovascular diseases. Naturally occurring bioactive compounds that have been shown to improve insulin sensitivity include chromium and polyphenols found in ...

  2. The diffusion of chromium in a duplex alloy steel

    International Nuclear Information System (INIS)

    Diffusion of chromium in a duplex stainless steel containing approximately 8% ferrite has been investigated in the temperature range 600 to 10000C using the standard serial sectioning technique. The resulting concentration profiles exhibited up to four distinct regions. The two main regions are attributed to volume diffusion in the austenite and ferrite phases, the other zones being due to short circuiting paths. Volume diffusion in the austenite phase is in good agreement with chromium diffusion in Type 316 steel. The chromium diffusion coefficient in the ferrite phase of approximate composition 25 wt % Cr, 5 wt % Ni is given by: Dsub(α) = (6.0(+11,-3)) x 10-6 exp - ((212+-5)/RT) m2s-1 the activation energy being expressed in kJ.mol-1. Little evidence was found for enhanced chromium diffusion along austenite/ferrite interface boundaries. (author)

  3. Grafted chromium 13-membered dioxo-macrocyclic complex into aminopropyl-based nanoporous SBA-15

    Energy Technology Data Exchange (ETDEWEB)

    Tarlani, Aliakbar, E-mail: Tarlani@ccerci.ac.ir [Inorganic Nanostructures and Catalysts Research Laboratory, Chemistry and Chemical Engineering Research Center of Iran, Pajoohesh Boulevard, km 17, Karaj Highway, Tehran 14968-13151 (Iran, Islamic Republic of); Joharian, Monika; Narimani, Khashayar [Inorganic Nanostructures and Catalysts Research Laboratory, Chemistry and Chemical Engineering Research Center of Iran, Pajoohesh Boulevard, km 17, Karaj Highway, Tehran 14968-13151 (Iran, Islamic Republic of); Muzart, Jacques [Institut de Chimie Moléculaire de Reims, CNRS-Université de Reims Champagne-Ardenne, BP 1039, 51687 Reims Cedex 2 (France); Fallah, Mahtab [Inorganic Nanostructures and Catalysts Research Laboratory, Chemistry and Chemical Engineering Research Center of Iran, Pajoohesh Boulevard, km 17, Karaj Highway, Tehran 14968-13151 (Iran, Islamic Republic of)

    2013-07-15

    In a new approach, chromium (III) tetraaza dioxo ligand was grafted onto functionalized SBA-15 after four step reactions by using coordinating ability of anchored amino functionalized SBA-15. After the termination of each step, the obtained product was characterized by FT-IR, low-angle X-ray diffraction (LA-XRD), N{sub 2} adsorption–desorption isotherms (Brunauer–Emmett–Teller (BET)–Barret–Joyner–Halenda (BJH)) and thermogravimetric analysis (TGA), and used as catalyst for the efficient and regioselective alcoholysis of styrene oxide to 2-alkoxy-1-phenylethanol product at ambient temperature. - Graphical abstract: Chromium (III) tetraaza dioxo ligand was grafted onto functionalized SBA-15 using coordinating ability of anchored amino functionalized SBA-15. Preparation of the catalyst is depicted in Scheme 1. - Highlights: • Dioxo tetraazachromium macrocyclic complex grafted into the SBA-15-NH{sub 2} channels. • The bond is created by coordinating ability of anchored amino functionalized SBA-15. • The prepared nanocatalyst has superior activity in the alcoholysis of styrene oxide. • The catalyst is reusable at ambient temperature for the mentioned reaction.

  4. Biosorption of Chromium (VI) from Aqueous Solutions onto Fungal Biomass

    OpenAIRE

    Ismael Acosta R.; Xöchitl Rodríguez; Conrado Gutiérrez; Ma. de Guadalupe Moctezuma

    2004-01-01

    The biosorption of chromium (VI) on eighteen different natural biosorbents: Natural sediment, chitosan, chitin, Aspergillus flavus I-V, Aspergillus fumigatus I-ll, Helmintosporium sp, Cladosporium sp, Mucor rouxii mutant, M. rouxii IM-80, Mucor sp-I and 2, Candida albicans and Cryptococcus neoformans was studied in this work. It was found that the biomass of C. neoformans, natural sediment, Helmintosporium sp and chitosan was more efficient to remove chromium (VI) (determined spectrophotometr...

  5. Stereology of carbide phase in modified hypereutectic chromium cast iron

    Directory of Open Access Journals (Sweden)

    J. Suchoń

    2010-04-01

    Full Text Available In paper are presented results of studies of carbide phase stereology modified hypereutectic wear resistance chromium cast iron which contains carbon about 3,5% and chromium about 25%. Three substances were applied to the modification: boron carbide (B4C, ferroniobium (FeNb and mixture of ferroniobium and rare-earth (RE. The measurements of geometrical features of carbides were conducted on microsection taken from castings wich were cooled with various velocities.

  6. Thermodynamic Equilibrium Diagrams of Sulphur-Chromium System

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The chemical and electrochemical equilibria in the presence of gaseous phase were investigated. Many substances, which consisted of sulphur and chromium, were considered. Various thermodynamic equilibria were calculated in different pressures. Calculation results were shown as log p―1/T and E―T diagrams. These diagrams may be used to study the corrosion of chromium in sulphur-containing circumstances. The diagrams are also used to thermodynami-cally determine the existence area of various substances and so on.

  7. Stereology of carbide phase in modified hypereutectic chromium cast iron

    OpenAIRE

    J. Suchoń; A. Studnicki; M. Przybył

    2010-01-01

    In paper are presented results of studies of carbide phase stereology modified hypereutectic wear resistance chromium cast iron which contains carbon about 3,5% and chromium about 25%. Three substances were applied to the modification: boron carbide (B4C), ferroniobium (FeNb) and mixture of ferroniobium and rare-earth (RE). The measurements of geometrical features of carbides were conducted on microsection taken from castings wich were cooled with various velocities.

  8. SCIENCE AND TECHNOLOGY ACTIVITIES FOR CHROMIUM IN THE 100 AREAS

    Energy Technology Data Exchange (ETDEWEB)

    PETERSEN SW

    2009-07-02

    {sm_bullet} Primary Objective: Protect the Columbia River - Focus is control and treatment of contamination at or near the shoreline, which is influenced by bank storage {sm_bullet} Secondary Objective: Reduce hexavalent chromium to <48 parts per billion (ppb) in aquifer (drinking water standard) - Large plumes with isolated areas of high chromium concentrations (> 40,000 ppb), - Unknown source location(s); probably originating in reactor operation areas

  9. Genetic Predisposition for Dermal Problems in Hexavalent Chromium Exposed Population

    OpenAIRE

    Priti Sharma; Vipin Bihari; Agarwal, Sudhir K.; Goel, Sudhir K.

    2012-01-01

    We studied the effect of genetic susceptibility on hexavalent chromium induced dermal adversities. The health status of population was examined from the areas of Kanpur (India) having the elevated hexavalent chromium levels in groundwater. Blood samples were collected for DNA isolation to conduct polymorphic determination of genes, namely: NQO1 (C609T), hOGG1 (C1245G), GSTT1, and GSTM1 (deletion). Symptomatic exposed subjects (n = 38) were compared with asymptomatic exposed subjects (n = 108)...

  10. Performance of chromium nitride based coatings under plastic processing conditions

    OpenAIRE

    Cunha, l.; Andritschky, M.; Pischow, K.; Wang, Z.(Institute of High Energy Physics, Beijing, China); Zarychta, A.; Miranda, A. S.; A.M. Cunha

    2000-01-01

    Chromium nitride based coatings were produced in the form of monolithic and multilayer coatings, by DC and RF reactive magnetron sputtering. These coatings were deposited onto stainless steel and tool steel substrates. Chromium nitride coatings have;proved to be wear and corrosion resistant. The combination of these characteristics was necessary to protect surfaces during plastic processing. In order to select the best coatings, some mechanical and tribological tests were performed. Har...

  11. DANGER OF HEXAVALENT CHROMIUM AND STRATEGY FOR THE REMEDITATION

    OpenAIRE

    Aniruddha Roy; Ayan Das; Nirmal Paul

    2013-01-01

    Some metals as micronutrients have a major role in the life and growth process of plants and animals. However, certain forms of some metals may also act as toxic material even in relatively small quantities. Chromium is such a metal, whose concentration above a certain limit may cause a serious problem to the health of living organisms. Chromium (Cr) may occur in several chemical forms in organic and inorganic systems. In biological systems only Cr (III) and Cr (VI) are signifi...

  12. Removal of hexavalent chromium in carbonic acid solution by oxidizing slag discharged from steelmaking process in electric arc furnace

    Science.gov (United States)

    Yokoyama, Seiji; Okazaki, Kohei; Sasano, Junji; Izaki, Masanobu

    2014-02-01

    Hexavalent chromium (Cr(VI)) is well-known to be a strong oxidizer, and is recognized as a carcinogen. Therefore, it is regulated for drinking water, soil, groundwater and sea by the environmental quality standards all over the world. In this study, it was attempted to remove Cr(VI) ion in a carbonic acid solution by the oxidizing slag that was discharged from the normal steelmaking process in an electric arc furnace. After the addition of the slag into the aqueous solution contained Cr(VI) ion, concentrations of Cr(VI) ion and total chromium (Cr(VI) + trivalent chromium (Cr(III)) ions decreased to lower detection limit of them. Therefore, the used slag could reduce Cr(VI) and fix Cr(III) ion on the slag. While Cr(VI) ion existed in the solution, iron did not dissolve from the slag. From the relation between predicted dissolution amount of iron(II) ion and amount of decrease in Cr(VI) ion, the Cr(VI) ion did not react with iron(II) ion dissolved from the slag. Therefore, Cr(VI) ion was removed by the reductive reaction between Cr(VI) ion and the iron(II) oxide (FeO) in the slag. This reaction progressed on the newly appeared surface of iron(II) oxide due to the dissolution of phase composed of calcium etc., which existed around iron(II) oxide grain in the slag.

  13. Effect of Arsenic and Chromium on the Serum Amino-Transferases Activity in Indian Major Carp, Labeo rohita

    Directory of Open Access Journals (Sweden)

    Anjaneyulu Yerramilli

    2007-09-01

    Full Text Available Arsenic and hexavalent chromium toxicity results from their ability to interact with sulfahydryl groups of proteins and enzymes, and to substitute phosphorus in a variety of biochemical reactions. Alanine aminotransferase (ALT; E.C: 2.6.1.2 and Aspartate amino transferase (AST; EC 2.6.1.1 play a crucial role in transamination reactions and can be used as potential biomarkers to indicate hepatotoxicity and cellular damage. While histopathological studies in liver tissue require more time and expertise, simple and reliable biochemical analysis of ALT and AST can be used for a rapid assessment of tissue and cellular damage within 96 h. The main objective of this study was to determine the acute effects of arsenic and hexavalent chromium on the activity of ALT and AST in the Indian major carp, Labeo rohita for 24 h and 96 h. Significant increase in the activity of ALT (P < 0.01 from controls in arsenic exposed fish indicates serious hepatic damage and distress condition to the fish. However, no such significant changes were observed in chromium-exposed fish suggesting that arsenic is more toxic to the fish. These findings indicate that ALT and AST are candidate biomarkers for arsenic-induced hepatotoxicity in Labeo rohita.

  14. Removal of Chromium and Lead from Industrial Wastewater Using

    Directory of Open Access Journals (Sweden)

    Mohamed Hilal

    2013-04-01

    Full Text Available In this research an attempt is made on the ability of aerobic treatment of synthetic solutions containing lead and chromium using effective microorganisms within the reactor. To achieve the desired objectives of the research, synthetic aqueous solutions of lead and chromium was used in the concentration of chromium and lead ions of 5, 10,50 and 100 mg / l .The work was done at constant pH equal to 4.5 and temperature of 30 ± 1 º C. Effective microorganisms solutions was added to the reactor at Vol.% of 1/50 ,1/100 ,1/500 and 1/1000, with retention time was 24 hours to measure the heavy metals concentration the atomic absorption device was used. The experimental results showed that each 1mg / l of lead and chromium ions need 24 mg of effective microorganisms to achieve removal of 92.0% and 82.60% for lead and chromium respectively. Increasing the concentration of effective microorganisms increases the surface of adsorption and thus increasing the removal efficiency. It is found that the microorganisms activity occur in the first five hours of processing and about 94% of adsorption capacity of biomass will take place. It is also found the selectivity of microorganisms to lead ions is higher than for chromium ions.

  15. Evaluating trivalent chromium toxicity on wild terrestrial and wetland plants.

    Science.gov (United States)

    Lukina, A O; Boutin, C; Rowland, O; Carpenter, D J

    2016-11-01

    Elevated chromium levels in soil from mining can impact the environment, including plants. Mining of chromium is concentrated in South Africa, several Asian countries, and potentially in Northern Ontario, Canada, raising concerns since chromium toxicity to wild plants is poorly understood. In the first experiment, concentration-response tests were conducted to evaluate effects of chromium on terrestrial and wetland plants. Following established guidelines using artificial soil, seeds of 32 species were exposed to chromium (Cr(3+)) at concentrations simulating contamination (0-1000 mg kg(-1)). This study found that low levels of chromium (250 mg kg(-1)) adversely affected the germination of 22% of species (33% of all families), while higher levels (500 and 1000 mg kg(-1)) affected 69% and 94% of species, respectively, from 89% of the families. Secondly, effects on seedbanks were studied using soil collected in Northern Ontario and exposed to Cr(3+) at equivalent concentrations (0-1000 mg kg(-1)). Effects were less severe in the seedbank study with significant differences only observed at 1000 mg kg(-1). Seeds exposed to Cr(3+) during stratification were greatly affected. Seed size was a contributing factor as was possibly the seed coat barrier. This study represents an initial step in understanding Cr(3+) toxicity on wild plants and could form the basis for future risk assessments. PMID:27543852

  16. Lime enhanced chromium removal in advanced integrated wastewater pond system.

    Science.gov (United States)

    Tadesse, I; Isoaho, S A; Green, F B; Puhakka, J A

    2006-03-01

    The removal of trivalent chromium from a combined tannery effluent in horizontal settling tanks and subsequent Advanced Integrated Wastewater Pond System (AIWPS) reactors was investigated. The raw combined effluent from Modjo tannery had pH in the range of 11.2-12. At this pH, a trivalent chromium removal of 46-72% was obtained in the horizontal settling tanks after a one-day detention time. Trivalent chromium precipitated as chromium hydroxide, Cr(OH)3. 58-95% Cr(III) was removed in the advanced facultative pond (AFP) where the water column pH of 7.2-8.4 was close to pH 8, which is the optimum precipitation pH for trivalent chromium. Chromium removals in the secondary facultative pond (SFP) and maturation pond (MP) were 30-50% and 6-16%, respectively. With Cr(III) concentration of 0.2-0.8 mg/l in the final treated effluent, the AIWPS preceded by horizontal settling tanks produced effluent that could easily meet most of the current Cr(III) discharge limits to receive water bodies.

  17. Experimental skin deposition of chromium on the hands following handling of samples of leather and metal

    DEFF Research Database (Denmark)

    Bregnbak, David; Thyssen, Jacob P.; Jellesen, Morten Stendahl;

    2016-01-01

    Background: Chromium is an important skin sensitizer. Exposure to it has been regulated in cement, and recently in leather. Studies on the deposition of chromium ions on the skin as a result of handling different chromium-containing materials are sparse, but could improve the risk assessment...... of contact sensitization and allergic contact dermatitis caused by chromium. Objectives: To determine whether the handling of chromium-containing samples of leather and metal results in the deposition of chromium onto the skin. Methods: Five healthy volunteers participated. For 30 min, they handled samples...... of leather and metal known to contain and release chromium. Skin deposition of chromium was assessed with the acid wipe sampling technique. Results: Acid wipe sampling of the participants' fingers showed chromium deposition on the skin in all participants who had been exposed to leather (range 0.01–0.20 µg...

  18. Ferrous sulphate mono and heptahydrate reduction of hexavalent chromium in cement: effectiveness and storability

    Directory of Open Access Journals (Sweden)

    Valverde, J. L.

    2005-09-01

    Full Text Available In Community legislation, substances containing hexavalent chromium are classified as carcinogenic, mutagenic and sensitizing. In cement, hexavalent chromium intensifies sensitization and may set off severe allergic reactions in workers in routine contact with the product, whether in the factory or on construction sites. The allergic or contact dermatitis causes is a very painful disease that may lead to permanent worker disability. According to Directive 2003/53/EC of the European Parliament and the Council, Governments of all member countries will be required to prohibit the marketing and use, as of 17 January 2005, of any cement or cement preparation containing more than 2 ppm of chromium (VI. Hexavalent chromium can be reduced with ferrous sulphate to trivalent chromium, which is water-insoluble and therefore innocuous to the skin. The present paper reports the effects of adding ferrous sulphate mono- or heptahydrate to a commercial cement and the storage time of the mix on the concentration of hexavalent chromium. The salts studied were found to effectively reduce hexavalent chromium in cement for at least three months.

    Las sustancias que contienen cromo hexavalente están clasificadas en la legislación comunitaria como sustancias carcinogénicas, mutagénicas y sensibilizantes. El cromo hexavalente del cemento potencia la sensibilización y provoca graves reacciones alérgicas que sufren bastante a menudo los trabajadores que lo manipulan habitualmente, ya sea en fábrica o en el sector de la construcción. La dermatitis alérgica o de contacto que produce es muy dolorosa y puede dejar a los trabajadores en estado de discapacidad. La Directiva 2003/53/CE del Parlamento Europeo y del Consejo, exige a los Gobiernos de los países miembros, que a partir del 17 de enero de 2005, prohiban el uso y la comercialización de todos aquellos cementos y preparados que contengan cemento, cuyo contenido en cromo (VI soluble, una vez hidratados

  19. Influence of promoters and oxidants on propane dehydrogenation over chromium-oxide catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Lapidus, A.L.; Agafonov, Yu.A.; Shaporeva, N.Yu.; Trushin, D.V.; Gaidai, N.A.; Nekrasov, N.V. [Russian Academy of Sciences, Moscow (Russian Federation). N.D. Zelinsky Inst. of Organic Chemistry

    2010-12-30

    Possibilities for increasing the efficiency of supported on SiO{sub 2} chromium-oxide catalysts in propane oxidative dehydrogenation in CO{sub 2} presence are investigated: the introduction of Li, Na, K, Ca in catalysts and the addition of O{sub 2} in the reaction mixture. It was been found that the positive role of K - the increase of the selectivity to propene and stability of catalysts at long-duration tests - appeared at the relation of Cr:K=20. It was shown that the presence of little amount of O{sub 2} (2%) in the reaction mixtures of propane and carbon dioxide resulted in the increase of propene yield and catalyst stability. (orig.)

  20. USE OF TWO DIGESTION METHODS IN THE EVALUATION OF CHROMIUM CONTENT IN CATTLE'S MEAT SUPPLEMENTED WITH CHROMIUM CHELATES

    OpenAIRE

    R. L. T. Andrade; P.S.A. Moreira; R. Arruda; F. J. Lourenço; C. Palhari, F. F. Faria, V. B. Arevalo; Faria, F. F.; V. B. Arevalo

    2015-01-01

    The present study aimed to analyze the chromium content in beef using two digestion methods. There were used samples from 24 18-month-old male cattle, and twelve of them were supplemented and twelve were not supplemented with chromium chelate. These samples were evaluated by atomic absorption spectroscopy, previously submitted to digestion method using nitric acid (65%) with hydrogen peroxide (35%) and to digestion method, using solution of nitric perchloric acid in the proportion 3:1. Immedi...

  1. Activation of bentonite to remove the chromium from waste water produced by panning industry, and studying the chromium recovery efficiency

    International Nuclear Information System (INIS)

    The fast development of tanning industry led to an increase in environmental problems resulting from discharging its wastes to the surrounding environment. Thus solving this problem became one of the most important aims that the researchers work on. The chromium content of the industrial water wastes of the tanning industry considered as the main pollutant for the environment. The Aleppo Bentonite is used in early research to remove the chromium from the industrial waste water.The current research aims to find a method to activate the Aleppo Bentonite in order to increase the effective removal of chromium from the industrial waste water which is produced by tanning industry, as well as to specify the optimal conditions for chromium recovery.This study used the Aleppo Bentonite, whose origin is Tal Ajar-Aleppo to study the activation aspects using Sulfuric Acid, Hydrochloric Acid and Nitric Acid, in addition to study the recovery aspects using the same acids and hydrogen peroxide and to specify the optimal conditions for chromium recovery through applying some experiments based on three main factors: concentration, settling time and temperature.It was observed from the applied experiments that it is possible to recover chromium from Bentonite efficiently up to (80% - 90%) by treating the Bentonite with hydrogen peroxide(33% concentration) at room temperature, or by treating it with hydrogen peroxide(8.25% concentration) at 75oC, while the settling time factor proved that full recovery of chromium is obtained during the first hour, and increasing the time factor does not affect the efficiency of chromium recovery. (author)

  2. Internal bremsstrahlung endpoint energy of 54Mn

    International Nuclear Information System (INIS)

    For 54Mn there is a discrepancy between the QEC obtained from the endpoint energy of the internal bremsstrahlung (IB) spectrum which accompanies the electron capture decay (QEC=1353±8 keV) and that obtained from the accepted mass differences (QEC=1377±1 keV). This Q value is needed to deduce the partial-half life of the astrophysically interesting β- decay of 54Mn from the recently measured β+ partial half-life. To resolve this discrepancy, we have remeasured the endpoint energy of the IB spectrum, by recording coincidences between the IB and the 835-keV γ ray, both detected in Compton-suppressed Ge detectors. The QEC we deduce is 1379±8 keV, in agreement with the accepted mass differences. (c) 2000 The American Physical Society

  3. Enhancing collagen stability through nanostructures containing chromium(III) oxide.

    Science.gov (United States)

    Sangeetha, Selvam; Ramamoorthy, Usha; Sreeram, Kalarical Janardhanan; Nair, Balachandran Unni

    2012-12-01

    Stabilization of collagen for various applications employs chemicals such as aldehydes, metal ions, polyphenols, etc. Stability against enzymatic, thermal and mechanical degradation is required for a range of biomedical applications. The premise of this research is to explore the use of nanoparticles with suitable functionalization/encapsulation to crosslink with collagen, such that the three dimensional architecture had the desired stability. Collagen solution prepared as per standard protocols is treated with chromium(III) oxide nanoparticules encapsulated within a polymeric matrix (polystyrene-block-polyacrylic acid copolymer). Selectivity towards encapsulation was ensured by the reaction in dimethyl sulfoxide, where the PS groups popped out and encapsulated the Cr(2)O(3). Subsequently when immersed in aqueous solution, PAA units popped up to react with functional groups of collagen. The interaction with collagen was monitored through techniques such as CD, FTIR, viscosity measurements, stress analysis. CD studies and FTIR showed no degradation of collagen. Thermal stability was enhanced upon interaction of nanostructures with collagen. Self-assembly of collagen was delayed but not inhibited, indicating a compete binding of the metal oxide encapsulated polymer to collagen. Metal oxide nanoparticles encapsulated within a polymeric matrix could provide thermal and mechanical stability to collagen. The formed fibrils of collagen could serve as ideal material for various smart applications such as slow/sustained drug release. The study is also relevant to the leather industry in that the nanostructures can diffuse through the highly networked collagen fibre bundles in skin matrix easily, thus overcoming the rate limiting step of diffusion. PMID:22766281

  4. Low energy spin excitations in chromium metal

    Energy Technology Data Exchange (ETDEWEB)

    Pynn, R. [Los Alamos National Lab., NM (United States); Azuah, R.T. [Hahn-Meitner-Inst., Berlin (Germany); Stirling, W.G. [Univ. of Liverpool (United Kingdom). Dept. of Physics; Kulda, J. [Inst. Laue Langevin, Grenoble (France)

    1997-12-31

    Neutron scattering experiments with full polarization analysis have been performed with a single crystal of chromium to study the low-energy spin fluctuations in the transverse spin density wave (TSDW) state. A number of remarkable results have been found. Inelastic scattering observed close to the TSDW satellite positions at (1 {+-} {delta},0,0) does not behave as expected for magnon scattering. In particular, the scattering corresponds to almost equally strong magnetization fluctuations both parallel and perpendicular to the ordered moments of the TSDW phase. As the Neel temperature is approached from below, scattering at the commensurate wavevector (1,0,0) increases in intensity as a result of critical scattering at silent satellites (1,0, {+-} {delta}) being included within the spectrometer resolution function. This effect, first observed by Sternlieb et al, does not account for all of the inelastic scattering around the (1,0,0) position, however, Rather, there are further collective excitations, apparently emanating from the TSDW satellites, which correspond to magnetic fluctuations parallel to the ordered TSDW moments. These branches have a group velocity that is close to that of (1,0,0) longitudinal acoustic (LA) phonons, but assigning their origin to magneto-elastic scattering raises other unanswered questions.

  5. 46 CFR 54.01-35 - Corrosion (modifies UG- 25).

    Science.gov (United States)

    2010-10-01

    ... (incorporated by reference; see 46 CFR 54.01-1) except as noted otherwise in this section. (b) The pressure... 46 Shipping 2 2010-10-01 2010-10-01 false Corrosion (modifies UG- 25). 54.01-35 Section 54.01-35... General Requirements § 54.01-35 Corrosion (modifies UG- 25). (a) Vessels or portions of vessels subject...

  6. 46 CFR 54.25-5 - Corrosion allowance.

    Science.gov (United States)

    2010-10-01

    ... Construction With Carbon, Alloy, and Heat Treated Steels § 54.25-5 Corrosion allowance. The corrosion allowance must be as required in 46 CFR 54.01-35. ... 46 Shipping 2 2010-10-01 2010-10-01 false Corrosion allowance. 54.25-5 Section 54.25-5...

  7. Hexavalent Chromium Reduction and Its Distribution in the Cell and Medium by Chromium Resistant Fusarium solani

    Directory of Open Access Journals (Sweden)

    Mousumi Sen

    2013-01-01

    Full Text Available In the present work, batch biosorption of Cr(VI was studied using the fungal strain isolated from soil. The fungal strain was characterized as Fusarium solani. The total Cr distribution in the biomass (fungus and in the media obtained from the experiment conducted at 500 mg l -1 initial Cr(VI concentration and pH 5.0. The results indicated both intracellular and extracellular accumulation and enzymatic reduction of Cr(VI and this was supported by the Transmission Electron Microscopic (TEM observation at the same Cr(VI concentration and pH value. Chromium elution from Fusarium solani containing Cr was then tried out using a number of chromium eluting reagents and a maximum Cr could be eluted using 0.5N sodium hydroxide solution without destructing the biomass structure. The total Cr was recovered by pH adjustment from both biomass and media was found to be 44% of the initial Cr(VI concentration (500 mg l-1.

  8. Low-chromium reduced-activation ferritic steels for fusion

    Energy Technology Data Exchange (ETDEWEB)

    Klueh, R.L.; Alexander, D.J.; Kenik, E.A. [Oak Ridge National Laboratory, TN (United States)

    1996-04-01

    Development of reduced-activation ferritic steels has concentrated on high-chromium (8-10 wt% Cr) steels. However, there are advantages for a low-chromium steel, and initial ORNL studies on reduced-activation steels were on compositions with 2.25 to 12% Cr. Those studies showed an Fe-2.25Cr-2W-0.25V-0.1C (2 1/4Cr-2WV) steel to have the highest strenglth of the steels studied. Although this steel had the best strength, Charpy impact properties were inferior to those of an Fe-9Cr-2W-0.25V-0.07Ta-0.1C (9Cr-2WVTa) and an Fe-2.25Cr-2W-0.1C (2 1/4Cr-2W) steel. Therefore, further development of the low-chromium Cr-W steels was required. These results indicate that it is possible to develop low-chromium reduced-activation ferritic steels that have tensile and impact properties as good or better than those of high-chromium (7-9% Cr) steels. Further improvement of properties should be possible by optimizing the composition.

  9. Bioaccumulation and biosorption of chromium by Aspergillus niger MTCC 2594.

    Science.gov (United States)

    Sandana Mala, John Geraldine; Unni Nair, Balachandran; Puvanakrishnan, Rengarajulu

    2006-06-01

    Chromium toxicity is of prime concern due to chrome tanning processes in the leather sector. Chrome tanning results in the discharge of toxic levels of chromium causing pollution hazards. Chromium levels of Cr(III) and Cr(VI) were high above permissible limits in chrome samples after chrome tanning. The potential of Aspergillus niger MTCC 2594 to accumulate chromium as well as its biosorption capacity is investigated in this study. Bioaccumulation of Cr(III) and Cr(VI) in the spent chrome liquor has resulted in a 75-78% reduction of the initial Cr content in 24-36 h. A. niger biomass is found to be very effective in the biosorption of Cr(III) and Cr(VI) in spent chrome liquor. Maximum adsorption of 83% for biosorption of Cr(III) at 48 h and 79% of Cr(VI) at 36 h in spent chrome liquor is observed. The biosorption characteristics fit well with Langmuir and Freundlich isotherms and the adsorption parameters are evaluated. The biosorption of Cr also follows Lagergren kinetics. A. niger biomass is effectively used for the biosorption of chromium with 79-83% Cr removal in 36-48 h.

  10. Chromium propionate enhances adipogenic differentiation of bovine intramuscular adipocytes

    Directory of Open Access Journals (Sweden)

    Rebecca eTokach

    2015-09-01

    Full Text Available In vitro experiments were performed to determine the effects of increasing concentrations of chromium propionate on mRNA and protein abundance of different enzymes and receptors. Intramuscular and subcutaneous preadipocytes and bovine satellite cells were isolated from the longissimus muscle to determine the effect of treatment on glucose transporter type 4 (GLUT4 and peroxisome proliferator-activated receptor γ mRNA and GLUT4 protein abundance. Preadipocyte cultures were treated with differentiation media plus either sodium propionate or different concentrations of chromium propionate (CrPro for 96, 120, and 144 h before harvest. This study indicated adipogenesis of the bovine intramuscular adipocytes were more sensitive to the treatment of chromium propionate as compared to subcutaneous adipocytes. Enhancement of adenosine monophosphate-activated protein kinase and GLUT4 mRNA by CrPro treatment may enhance glucose uptake in intramuscular adipocytes. Chromium propionate decreased GLUT4 protein levels in muscle cell cultures suggesting those cells have increased efficiency of glucose uptake due to exposure to increased levels of CrPro. In contrast, each of the two adipogenic lines had opposing responses to the CrPro. It appeared that CrPro had the most stimulative effect of GLUT4 response in the intramuscular adipocytes as compared to subcutaneous adipocytes. These findings indicated opportunities to potentially augment marbling in beef cattle fed chromium propionate during the finishing phase.

  11. Anthropogenic chromium emissions in china from 1990 to 2009.

    Science.gov (United States)

    Cheng, Hongguang; Zhou, Tan; Li, Qian; Lu, Lu; Lin, Chunye

    2014-01-01

    An inventory of chromium emission into the atmosphere and water from anthropogenic activities in China was compiled for 1990 through to 2009. We estimate that the total emission of chromium to the atmosphere is about 1.92×10⁵ t. Coal and oil combustion were the two leading sources of chromium emission to the atmosphere in China, while the contribution of them showed opposite annual growth trend. In total, nearly 1.34×10⁴ t of chromium was discharged to water, mainly from six industrial categories in 20 years. Among them, the metal fabrication industry and the leather tanning sector were the dominant sources of chromium emissions, accounting for approximately 68.0% and 20.0% of the total emissions and representing increases of 15.6% and 10.3% annually, respectively. The spatial trends of Cr emissions show significant variation based on emissions from 2005 to 2009. The emission to the atmosphere was heaviest in Hebei, Shandong, Guangdong, Zhejiang and Shanxi, whose annual emissions reached more than 1000t for the high level of coal and oil consumption. In terms of emission to water, the largest contributors were Guangdong, Jiangsu, Shandong and Zhejiang, where most of the leather production and metal manufacturing occur and these four regions accounted for nearly 47.4% of the total emission to water. PMID:24505309

  12. Anthropogenic chromium emissions in china from 1990 to 2009.

    Directory of Open Access Journals (Sweden)

    Hongguang Cheng

    Full Text Available An inventory of chromium emission into the atmosphere and water from anthropogenic activities in China was compiled for 1990 through to 2009. We estimate that the total emission of chromium to the atmosphere is about 1.92×10⁵ t. Coal and oil combustion were the two leading sources of chromium emission to the atmosphere in China, while the contribution of them showed opposite annual growth trend. In total, nearly 1.34×10⁴ t of chromium was discharged to water, mainly from six industrial categories in 20 years. Among them, the metal fabrication industry and the leather tanning sector were the dominant sources of chromium emissions, accounting for approximately 68.0% and 20.0% of the total emissions and representing increases of 15.6% and 10.3% annually, respectively. The spatial trends of Cr emissions show significant variation based on emissions from 2005 to 2009. The emission to the atmosphere was heaviest in Hebei, Shandong, Guangdong, Zhejiang and Shanxi, whose annual emissions reached more than 1000t for the high level of coal and oil consumption. In terms of emission to water, the largest contributors were Guangdong, Jiangsu, Shandong and Zhejiang, where most of the leather production and metal manufacturing occur and these four regions accounted for nearly 47.4% of the total emission to water.

  13. Enhancement of chromium uptake in tanning using oxazolidine.

    Science.gov (United States)

    Sundarapandiyan, S; Brutto, Patrick E; Siddhartha, G; Ramesh, R; Ramanaiah, B; Saravanan, P; Mandal, A B

    2011-06-15

    Monocyclic and bicyclic oxazolidines were offered at three different junctures of chrome tanning process viz. prior to BCS offer, along with BCS and after basification. It was found that oxazolidine when offered after basification brought about better chromium uptake and reduction of chromium load in the wastewater. Offer of oxazolidine was also varied. Increase in offer of oxazolidine from 0.25% to 1% was found to enhance the chromium uptake and decrease the chromium load in wastewater. But the increase in uptake was not proportionate to the increase in oxazolidine offer more than 0.75%. Offer of 1% Zoldine ZA 78 (monocyclic oxazolidine) and Zoldine ZE (bicyclic oxazolidine) after basification brought about 63.4% and 73.1% enhancement in chrome content in leather compared to control where oxazolidine was not offered. The tone of the wetblue was found to be altered moderately. However this did not call for any process adjustments in wet-finishing. The oxazolidine treated leathers were found to be immensely fuller and tighter. It was found experimentally that offer of 1% of oxazolidine facilitated reduction in the offer of syntans administered for filling and grain tightening by around 46%. Oxazolidine could bring about significant reduction in cost of chemicals apart from resulting environmental benefits due to enhancement of chromium uptake during tanning. PMID:21536383

  14. Lepton flavor model from Δ(54) symmetry

    International Nuclear Information System (INIS)

    We present the lepton flavor model with Δ(54), which appears typically in heterotic string models on the T2/Z3 orbifold. Our model reproduces the tri-bimaximal mixing in the parameter region around degenerate neutrino masses or two massless neutrinos. We predict the deviation from the tri-bimaximal mixing by putting the experimental data of neutrino masses in the normal hierarchy of neutrino masses. The upper bound of sin 2θ13 is 0.01. There is the strong correlation between θ23 and θ13. Unless θ23 is deviated from the maximal mixing considerably, θ13 remains to be tiny.

  15. Reduction of chromium oxide from slags

    Directory of Open Access Journals (Sweden)

    Gutiérrez-Paredes, J.

    2005-12-01

    Full Text Available Experimental and theoretical work were performed to estimate the effect of slag basicity and amount of reducing agents on the reduction of chromium oxide from the slag which interacted with molten steel at 1,600 °C. The slag system contained CaO, MgO, SiO2, CaF2 and Cr2O3 together with Fe-alloys (Fe-Si and Fe-Si-Mg. The CaF2 and MgO contents in the slags were 10 mass % each; Cr2O3 was 25%. The amount of the ferroalloys ranged from 12.5 to 50 g per 100 g of slag. The (CaO+MgO/SiO2 ratio was held at 1 and 2. The Cr yield was determined using both Fe-alloys as reducing agents. Some estimations were made to determine the theoretical effect of temperature, slag basicity, (CaO+MgO/SiO2, and amount of reducing agents in the slag on the chromium recovery. The FACT (Facility for the Analysis of Chemical Thermodynamics computational package is used to determine the equilibrium between the slag and molten steel.

    En el presente trabajo se realiza un estudio teórico y experimental para determinar el efecto de la basicidad de la escoria y la cantidad de agentes reductores sobre la reducción de óxidos de cromo contenidos en la escoria, la cual está en contacto con acero líquido a 1.600 °C. La escoria se prepara con los reactivos CaO, MgO, SiO2, CaF2 y ferroaleaciones (Fe-Si y Fe-Si-Mg. Los contenidos de CaF2 y MgO en la escoria son de 10 %, cada uno, y el de Cr2O3 es 25 %. La cantidad de la ferroaleación varía de 12,5 a 50 g por cada 100 g de escoria. La relación (CaO+MgO/SiO2 tiene los valores de 1 y 2. Se determina la eficiencia de recuperación de cromo empleando los dos tipos de ferroaleaciones. Se realizaron cálculos para determinar el efecto teórico de la temperatura, la basicidad de la escoria, (CaO+MgO/SiO2, y la cantidad de agentes reductores sobre la reducci

  16. Electrochemical modification of chromium surfaces using 4-nitro- and4-fluorobenzenediazonium salts

    DEFF Research Database (Denmark)

    Hinge, Mogens; Cecatto, Marcel; Kingshott, Peter;

    2009-01-01

    Chromium surfaces can be electrografted with organic surface films using 4-nitro- or 4-fluorobenzenediazonium salts, despite the fact that the surfaces are covered with a protective chromium oxide layer...

  17. FORMATION AND DESTRUCTION OF HEXAVALENT CHROMIUM IN A LABORATORY SWIRL FLAME INCINERATOR

    Science.gov (United States)

    The partitioning of chromium (Cr) in combustion systems was investigated theoretically and experimentally. Theoretical predictions were based on chemical equilibrium and suggested that hexavalent chromium [Cr(VI)] was favored by the presence of chlorine (Cl) and diminished by the...

  18. Effective bioleaching of chromium in tannery sludge with an enriched sulfur-oxidizing bacterial community.

    Science.gov (United States)

    Zeng, Jing; Gou, Min; Tang, Yue-Qin; Li, Guo-Ying; Sun, Zhao-Yong; Kida, Kenji

    2016-10-01

    In this study, a sulfur-oxidizing community was enriched from activated sludge generated in tannery wastewater treatment plants. Bioleaching of tannery sludge containing 0.9-1.2% chromium was investigated to evaluate the effectiveness of the enriched community, the effect of chromium binding forms on bioleaching efficiency, and the dominant microbes contributing to chromium bioleaching. Sludge samples inoculated with the enriched community presented 79.9-96.8% of chromium leaching efficiencies, much higher than those without the enriched community. High bioleaching efficiencies of over 95% were achieved for chromium in reducible fraction, while 60.9-97.9% were observed for chromium in oxidizable and residual fractions. Acidithiobacillus thiooxidans, the predominant bacteria in the enriched community, played an important role in bioleaching, whereas some indigenous heterotrophic species in sludge might have had a supporting role. The results indicated that A. thiooxidans-dominant enriched microbial community had high chromium bioleaching efficiency, and chromium binding forms affected the bioleaching performance.

  19. CHROMIUM ELECTROANALYSIS AT SCREEN PRINTED ELECTRODE MODIFIED BY THIN FILMS OF NICKEL

    Science.gov (United States)

    A rapid and potentially cost-effective electrochemical method is reported for analysis of chromium (VI) and Chromium(III) using a nickel modified screen printed carbon ink electrode. Electrochemical characteristics of nickel modified electrode as well voltammetric behavior f...

  20. Performance enhancement of iron-chromium redox flow batteries by employing interdigitated flow fields

    Science.gov (United States)

    Zeng, Y. K.; Zhou, X. L.; Zeng, L.; Yan, X. H.; Zhao, T. S.

    2016-09-01

    The catalyst for the negative electrode of iron-chromium redox flow batteries (ICRFBs) is commonly prepared by adding a small amount of Bi3+ ions in the electrolyte and synchronously electrodepositing metallic particles onto the electrode surface at the beginning of charge process. Achieving a uniform catalyst distribution in the porous electrode, which is closely related to the flow field design, is critically important to improve the ICRFB performance. In this work, the effects of flow field designs on catalyst electrodeposition and battery performance are investigated. It is found that compared to the serpentine flow field (SFF) design, the interdigitated flow field (IFF) forces the electrolyte through the porous electrode between the neighboring channels and enhances species transport during the processes of both the catalyst electrodeposition and iron/chromium redox reactions, thus enabling a more uniform catalyst distribution and higher mass transport limitation. It is further demonstrated that the energy efficiency of the ICRFB with the IFF reaches 80.7% at a high current density (320 mA cm-2), which is 8.2% higher than that of the ICRFB with the SFF. With such a high performance and intrinsically low-cost active materials, the ICRFB with the IFF offers a great promise for large-scale energy storage.

  1. Chromium isotope composition of reducing and anoxic sediments from the Peru Margin and Cariaco Basin

    Science.gov (United States)

    Gueguen, B.; Planavsky, N.; Wang, X.; Algeo, T. J.; Peterson, L. C.; Reinhard, C. T.

    2014-12-01

    Chromium isotope systematics in marine sediments are now being used as a new redox proxy of the modern and ancient Earth's surface. Chromium is primarily delivered to the oceans by riverine inputs through weathering of Cr(III)-rich minerals present in the continental crust and oxidation of insoluble Cr(III) to soluble Cr(VI) species. Since oxidation-reduction reactions fractionate Cr isotopes whereby oxidized Cr(VI) species are preferentially enriched in heavy Cr isotopes, the Cr isotope composition of marine sediments may be useful tracers of redox conditions at the Earth's surface through geological time. Chromium is quantitatively removed in organic-rich sediments where reducing conditions prevail and promote reduction of Cr(VI) to Cr(III), and thus, these sediments should capture the ambient seawater Cr isotope composition. However, the isotopic composition of modern organic-rich sediments is poorly documented so far, and this step is essential for further modeling the global oceanic Cr isotope mass balance and assessing the effects of sedimentation and post-depositional processes on the marine Cr isotopes archive. In this study, we have characterized modern marine organic-rich sediments for their Cr isotope composition (δ53/52Cr) from two different settings, the Peru margin upwelling zone and the anoxic Cariaco Basin (Venezuela). Chromium isotopes were measured on a MC-ICP-MS (Nu Plasma) using a double-spike correction method. The authigenic fraction of shallow samples from the Peru margin sedimentary sequence with a high Total Organic Carbon (TOC) content (>10 wt%) yield an average δ53/52Crauthigenic value of +0.67 ±0.05 ‰ (2sd). However, although this value is close to the seawater value (Atlantic Ocean) and to Cariaco basin sediments (~ +0.6 ‰), reducing sediments from the Peru margin are on average isotopically slightly heavier, especially in samples having a low authigenic fraction and a low TOC content (δ53/52Crauthigenic values up to +1.30

  2. Reduction and immobilization of hexavalent chromium by microbially reduced Fe-bearing clay minerals

    Science.gov (United States)

    Bishop, Michael E.; Glasser, Paul; Dong, Hailiang; Arey, Bruce; Kovarik, Libor

    2014-05-01

    Hexavalent chromium (Cr6+) is a major contaminant in the environment. As a redox-sensitive element, the fate and toxicity of chromium is controlled by reduction-oxidation (redox) reactions. Previous research has shown the ability of structural Fe(II) in naturally present and chemically reduced clay minerals to reduce Cr6+ to Cr(III) as a way of immobilization and detoxification. However, it is still poorly known whether or not structural Fe(II) in biologically reduced clay minerals exhibits a similar reactivity and if so, what the kinetics and mechanisms of Cr6+ reduction are. The objective of this study was to determine the kinetics and possible mechanisms of Cr6+ reduction by structural Fe(II) in microbially reduced clay minerals and the nature of reduced Cr(III). Structural Fe(III) in nontronite (NAu-2), montmorillonite (SWy-2), chlorite (CCa-2), and clay-rich sediments from the Ringold Formation of the Hanford site of Washington State, USA was first bioreduced to Fe(II) by an iron-reducing bacterium Geobacter sulfurreducens with acetate as the sole electron donor and anthraquinone-2,6-disulfonate (AQDS) as electron shuttle in synthetic groundwater (pH 7). Biogenic Fe(II) was then used to reduce aqueous Cr6+ at three different temperatures, 10, 20, and 30 °C, in order to determine the temperature dependence of the redox reaction between Cr6+ and clay-Fe(II). The results showed that nontronite and montmorillonite were most effective in reducing aqueous Cr6+ at all three temperatures. In contrast, most Fe(II) in chlorite was not reactive towards Cr6+ reduction at 10 °C, though at 30 °C there was some reduction. For all the clay minerals, the ratio of total Fe(II) oxidized to Cr6+ reduced was close to the expected stoichiometric value of 3. Characterization of the Cr-clay reaction product with scanning electron microscopy with focused ion beam and transmission electron microscopy with electron energy loss spectroscopy revealed that reduced chromium was possibly

  3. Reduction And Immobilization Of Hexavalent Chromium By Microbially Reduced Fe-bearing Clay Minerals

    Energy Technology Data Exchange (ETDEWEB)

    Bishop, Michael E.; Glasser, Paul; Dong, Hailiang; Arey, Bruce W.; Kovarik, Libor

    2014-05-15

    Hexavalent chromium (Cr6+) is a major contaminant in the environment. As a redox-sensitive element, the fate and toxicity of chromium is controlled by reduction-oxidation (redox) reactions. Previous research has shown the ability of structural Fe(II) in naturally present and chemically reduced clay minerals to reduce Cr6+ to Cr(III) as a way of immobilization and detoxification. However, it is still poorly known whether or not structural Fe(II) in biologically reduced clay minerals exhibits a similar reactivity and if so, what the kinetics and mechanisms of Cr6+ reduction are. The objective of this study was to determine the kinetics and possible mechanisms of Cr6+ reduction by structural Fe(II) in microbially reduced clay minerals and the nature of reduced Cr(III). Structural Fe(III) in nontronite (NAu-2), montmorillonite (SWy-2), chlorite (CCa-2), and clay-rich sediments from the Ringold Formation of the Hanford site of Washington State, USA was first bioreduced to Fe(II) by an iron-reducing bacterium Geobacter sulfurreducens with acetate as the sole electron donor and anthraquinone-2,6-disulfate (AQDS) as electron shuttle in synthetic groundwater (pH 7). Biogenic Fe(II) was then used to reduce aqueous Cr6+ at three different temperatures, 10°, 20°, and 30°C, in order to determine the temperature dependence of the redox reaction between Cr6+ and clay-Fe(II). The results showed that nontronite and montmorillonite were most effective in reducing aqueous Cr6+ at all three temperatures. In contrast, most Fe(II) in chlorite was not reactive towards Cr6+ reduction at 10°C, though at 30°C there was some reduction. For all the clay minerals, the ratio of total Fe(II) oxidized to Cr6+ reduced was close to the expected stoichiometric value of 3. Characterization of the Cr-clay reaction product with scanning electron microscopy with focused ion beam and transmission electron microscopy with electron energy loss spectroscopy revealed that reduced chromium was possibly

  4. Scientific Opinion on chromium(III lactate tri-hydrate as a source of chromium added for nutritional purposes to foodstuff

    Directory of Open Access Journals (Sweden)

    EFSA Panel on Food Additives and Nutrient Sources added to Food (ANS

    2012-10-01

    Full Text Available

    The Panel on Food Additives and Nutrient Sources added to Food provides a scientific opinion on the safety and bioavailability of chromium(III lactate tri-hydrate as a source of chromium(III added for nutritional purposes to foodstuffs. The safety of chromium itself, in terms of the amounts that may be consumed, is outside the remit of this Panel. No new data have been provided as regards the safety and bioavailability of chromium from chromium(III lactate tri-hydrate. The Panel concurs with its earlier views stating that no evidence was provided supporting the bioavailability of chromium from chromium(III lactate tri-hydrate. Chromium(III lactate tri-hydrate is claimed to be freely soluble in water, however, chromium(III lactate tri-hydrate exists as a weak complex that may influence the bioavailability of chromium(III in the gastrointestinal tract. The Panel re-iterates that because of the complex chemistry of chromium(III lactate tri-hydrate in aqueous solutions and its limited solubility at pH >5, the bioavailability of chromium(III from chromium(III lactate tri-hydrate is low. Based on a conservative exposure estimate, the Panel calculated the combined intake of chromium(III from supplements and from foods fortified with chromium(III lactate tri-hydrate, for both adults and children, to be approximately 240 μg chromium(III/day, which is below the value of 250 µg/day established by the WHO for supplemental intake of chromium that should not be exceeded. The Panel noted that the use of chromium(III lactate tri-hydrate in the form of a premix with lactose, added to foods, would result in an exposure at the mean for adults of approximately 7-37 mg lactose/day (0.12-0.62 μg lactose/kg bw/day and to 36-192 μg lactate/day (0.60-3.20 μg/kg bw/day. Given that subjects with lactose maldigestion will tolerate up to 12 g of lactose with no or minor symptoms, these levels are not of safety concern.

  5. Biosorption of hexavalent chromium in a tannery industry wastewater using fungi species

    OpenAIRE

    Sivakumar, D.

    2016-01-01

    The isolated fungi species of different kinds from chromium contaminated soil sites located in Nagalkeni, Chennai were used for reducing chromium(VI) in a tannery industry wastewater of Nagalkeni, Chennai.  The experiments were conducted to know biosorption potential of isolated fungi species for removing chromium(VI) in a tannery industry wastewater against the different pH, fungi biomass and chromium(VI) concentration (dilution ratio).  The results of this study indicated that the order of ...

  6. Investigation of hexavalent chromium removal from Synthetic wastewater by using Peaganum

    OpenAIRE

    Ali Akbar Taghizadeh; Maryam khodadadi; Taher Shahriary; Hadighe Dorri; mahla zaferanieh; rasoul khosravi

    2012-01-01

    Background and Aim: Discharge of industrial wastewater containing hexavalent chromium into the environment can have harmful effects to the types of organisms. So, chromium should remove before discharging to the environment with an effective method. The purpose of this study of is hexavalent chromium removed with Peganum harmala granular seeds(PGS).   Materials and Methods: In this experimental study, The removal of hexavalent chromium with using PGS, with changes in time, pH, adsorbent dose,...

  7. Influence of chromium, oxygen, carbon and nitrogen on iron viscosity

    International Nuclear Information System (INIS)

    Kinetic viscosity of 70 beforehand melted iron samples with additions of chromium (up to 2%) and carbon (up to 1%) has been investigated. Different conditions of melting brought about differences in oxygen and nitrogen contents. Viscosity of most samples has been determined in the 1550-1650 deg C temperature range. It is stated that small additions to pure iron of each of the investigated elements (O, Cr, C, N) decrease its viscosity. Combined effect of these additions on viscosity is inadditive. Simultaneous introduction of oxygen and carbon may result in increase of melt viscosity. The same fact is observed at combined introduction of chromium and nitrogen. Simultaneous introduction of other impurities-chromium with oxygen or carbon, nitrogen with oxygen causes amplification of their individual effect. Reasons for the observed regularities result from changes in energies of interparticle interactions in the melt and therefore rebuilding of structure of its short-range order

  8. A study of the process of desorption of hexavalent chromium

    Directory of Open Access Journals (Sweden)

    W.B. Amorim

    2003-09-01

    Full Text Available In this work the process of desorption of hexavalent chromium, a toxic metal ion, from the marine algae Sargassum sp, following biosorption experiments 2³ factorial design was studied. A technique was applied to three eluents: HCl, H2SO4 and EDTA. Three factors of importance were evaluated: concentration of eluent, the ratio between mass of biosorbent and volume of eluent (S/L and process time. A statistical analysis of the experimental results showed that the three variables evaluated are significant for all three eluents. The models for chromium desorption were validated, as the results agreed well with the observed values. Through use of the response surface methodology, a factorial design based optimization technique; it was possible to identify the most suitable eluent and the interval of values for the process variables that resulted in the most significant desorption of chromium, which is relevant information for work aiming at process optimization.

  9. Structural and magnetic properties of chromium doped zinc ferrite

    International Nuclear Information System (INIS)

    Zinc chromium ferrites with chemical formula ZnCrxFe2−xO4 (x = 0.0, 0.2, 0.4, 0.6, 0.8, 1.0) were prepared by Sol - Gel technique. The structural as well as magnetic properties of the synthesized samples have been studied and reported here. The structural characterizations of the samples were analyzed by using X – Ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscope (SEM), and Transmission Electron Microscope (TEM). The single phase spinel cubic structure of all the prepared samples was tested by XRD and FTIR. The particle size was observed to decrease from 18.636 nm to 6.125 nm by chromium doping and induced a tensile strain in all the zinc chromium mixed ferrites. The magnetic properties of few samples (x = 0.0, 0.4, 1.0) were investigated using Vibrating Sample Magnetometer (VSM)

  10. Chromium Resistant Bacteria: Impact on Plant Growth in Soil Microcosm

    Directory of Open Access Journals (Sweden)

    Sayel Hanane

    2014-07-01

    Full Text Available Three chromium resistant bacterial strains, Pseudomonas fluorescens PF28, Enterobacter amnigenus EA31 and Enterococcus gallinarum S34 isolated from tannery waste contaminated soil were used in this study. All strains could resist a high concentration of K2Cr2O7 that is up to 300 mg/L. The effect of these strains on clover plants (Trifolium campestre in the presence of two chromium salts CrCl3 and K2Cr2O7 was studied in soil microcosm. Application of chromium salts adversely affected seed germination, root and shoot length. Bacterial inoculation improved the growth parameters under chromate stress when compared with non inoculated respective controls. There was observed more than 50% reduction of Cr(VI in inoculated soil microcosms, as compared to the uninoculated soil under the same conditions. The results obtained in this study are significant for the bioremediation of chromate pollution.

  11. Electron magnetic resonance investigation of chromium diffusion in yttria powders

    Energy Technology Data Exchange (ETDEWEB)

    Biasi, R.S. de, E-mail: rsbiasi@ime.eb.b [Secao de Engenharia Mecanica e de Materiais, Instituto Militar de Engenharia, Pr. General Tiburcio, 80, 22290-270 Rio de Janeiro, RJ (Brazil); Grillo, M.L.N., E-mail: mluciag@uerj.b [Instituto de Fisica, Universidade do Estado do Rio de Janeiro, 20550-013 Rio de Janeiro, RJ (Brazil)

    2010-03-01

    The electron magnetic resonance (EMR) technique was used to investigate the diffusion of chromium in yttria (Y{sub 2}O{sub 3}) powders. The EMR absorption intensity was measured for several annealing times and three different temperatures of isothermal annealing: 1273, 1323 and 1373 K. The activation temperature for diffusion, calculated from the experimental data using a theoretical model based on the Fick equation, was found to be E{sub A}=342+-5 kJ mol{sup -1}. This value is larger than the activation energy for the diffusion of chromium in rutile (TiO{sub 2}), periclase (MgO) and cobalt monoxide (CoO) and smaller than the activation energy for the diffusion of chromium in chrysoberyl (BeAl{sub 2}O{sub 4}).

  12. Catalysis of Manganese(Ⅱ) on Chromium(Ⅵ) Reduction by Citrate

    Institute of Scientific and Technical Information of China (English)

    LI Chen; LAN Ye-Qing; DENG Bao-Lin

    2007-01-01

    The catalysis of manganese(Ⅱ) (Mn2+) on chromium(Ⅵ) (Cr6+) reduction by citrate was studied through batch experiments with the concentration of citrate greatly in excess of Cr6+ at 25℃ and in pH ranges of 4.0 to 5.0. Results showed that at pH 4.5 within 22 h direct reduction of Cr6+ by citrate was not observed, but for the same time when Mn2+ (50 to 200 μmol L-1 was added,nearly all Cr6+ was rdeuced ,with the higher initial Mn2+ concentration having faster Cr6+ reduction. In the initial stage of the reaction, the Cr6+ reduction could be described with a pseudo-first-order kinetics equation. In the later stage of the reaction, plots of lnc(Cr6+) versus t, where c(Cr6+) is the Cr6+ concentration in the reaction and t is the reaction time, deviated from the initial linear trend. The deviations suggested that the pseudo-first-order kinetics did not apply to the whole experimental period and that some reaction intermediates could have greatly accelerated Cr6+ reduction by citrate. The catalysis of the intermediates increased with the reaction time and gradually reached stability. Then, the plot of lnc(Cr6+) versus t in the presence of Mn2+ was linear again, with the rate constant increasing by 102 times compared with the absence of Mn2+. Complexation between Mn2+ and citrate was likely a prerequisite for the catalysis of Mn2+ on the reaction. Additional experiments showed that introducing ethylenediaminetetraacetic acid (EDTA) into the reaction system strongly suppressed the catalysis of Mn2+.

  13. Chromium accumulation by the hyperaccumulator plant Leersia hexandra Swartz.

    Science.gov (United States)

    Zhang, Xue-Hong; Liu, Jie; Huang, Hai-Tao; Chen, Jun; Zhu, Yi-Nian; Wang, Dun-Qiu

    2007-04-01

    Leersia hexandra Swartz (Gramineae), which occurs in Southern China, has been found to be a new chromium hyperaccumulator by means of field survey and pot-culture experiment. The field survey showed that this species had an extraordinary accumulation capacity for chromium. The maximum Cr concentration in the dry leaf matter was 2978 mg kg(-1) on the side of a pond near an electroplating factory. The average concentration of chromium in the leaves was 18.86 times as that in the pond sediment, and 297.41 times as that in the pond water. Under conditions of the nutrient solution culture, it was found that L. hexandra had a high tolerance and accumulation capacity to Cr(III) and Cr(VI). Under 60 mg l(-1) Cr(III) and 10 mg l(-1) Cr(VI) treatment, there was no significant decrease of biomass in the leaves of L. hexandra (p>0.05). The highest bioaccumulation coefficients of the leaves for Cr(III) and Cr(VI) were 486.8 and 72.1, respectively. However, L. hexandra had a higher accumulation capacity for Cr(III) than for Cr(VI). At the Cr(III) concentration of 10 mg l(-1) in the culture solution, the concentration of chromium in leaves was 4868 mg kg(-1), while at the same Cr(VI) concentration, the concentration of chromium in leaves was only 597 mg kg(-1). These results confirmed that L. hexandra is a chromium hyperaccumulator which grows rapidly with a great tolerance to Cr and broad ecological amplitude. This species could provide a new plant resource that explores the mechanism of Cr hyperaccumulation, and has potential for usage in the phytoremediation of Cr-contaminated soil and water. PMID:17207838

  14. 21 CFR 73.3110a - Chromium-cobalt-aluminum oxide.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Chromium-cobalt-aluminum oxide. 73.3110a Section... LISTING OF COLOR ADDITIVES EXEMPT FROM CERTIFICATION Medical Devices § 73.3110a Chromium-cobalt-aluminum oxide. (a) Identity. The color additive chromium-cobalt-aluminum oxide (Pigment Blue 36) (CAS Reg....

  15. 75 FR 60454 - Draft Toxicological Review of Hexavalent Chromium: In Support of Summary Information on the...

    Science.gov (United States)

    2010-09-30

    ... AGENCY Draft Toxicological Review of Hexavalent Chromium: In Support of Summary Information on the..., ``Toxicological Review of Hexavalent Chromium: In Support of Summary Information on the Integrated Risk..., 2010. The listening session on the draft assessment for hexavalent chromium will be held on November...

  16. 76 FR 20349 - Draft Toxicological Review of Hexavalent Chromium: In Support of Summary Information on the...

    Science.gov (United States)

    2011-04-12

    ... AGENCY Draft Toxicological Review of Hexavalent Chromium: In Support of Summary Information on the..., ``Toxicological Review of Hexavalent Chromium: In Support of Summary Information on the Integrated Risk... workshop on the draft assessment for Hexavalent Chromium will be held on May 12, 2011, beginning at 8:30...

  17. 77 FR 61431 - Hexavalent Chromium Standards; Extension of the Office of Management and Budget's (OMB) Approval...

    Science.gov (United States)

    2012-10-09

    ... Occupational Safety and Health Administration Hexavalent Chromium Standards; Extension of the Office of...) approval of the information collection requirements specified in the Hexavalent Chromium Standards for... requirements specified in the Hexavalent Chromium (Cr(VI)) Standards for General Industry (29 CFR...

  18. Speciation dependent radiotracer studies on chromium preconcentration using iron doped calcium alginate biopolymer

    International Nuclear Information System (INIS)

    The work aims to study the differential attitude of Ca-alginate (CA) and Fe-doped calcium alginate (Fe-CA) and towards Cr(III) and Cr (IV) so that, depending on the oxidation state of chromium effluent, environmentally sustainable methodologies can be prescribed for removal of chromium. Throughout the experiment 51Cr has been used as the precursor of stable chromium

  19. Evaluation of flexural bond strength of porcelain to used nickel-chromium alloy in various percentages

    Directory of Open Access Journals (Sweden)

    VNV Madhav

    2012-01-01

    Fresh nickel-chromium alloy shows the greatest porcelain adherence.There is no significant change in bond strength of ceramic to alloy with up to 75% of used nickel-chromium alloy.At least 25%- of new alloy should be added when recycled nickel-chromium alloy is being used for metal ceramic restorations.

  20. Fertilizers and Mixed Crop Cultivation of Chromium Tolerant and Sensitive Plants under Chromium Toxicity.

    Science.gov (United States)

    Dheeba, B; Sampathkumar, P; Kannan, K

    2015-01-01

    Zea mays (maize) and Vigna radiata (green gram) are found to be the chromium (Cr) tolerant and sensitive plants, respectively. In the present paper, we investigate the reduction of the toxicity of Cr in the sensitive plants by the mixed crop cultivation in the field using various amendments. Further, the potassium dichromate was used as the source of hexavalent Cr. The results indicated that Cr adversely affects both the growth and yield of plants. The soil properties vary with Cr and different fertilizer amendments and the yield of both plants were affected by Cr. We conclude that metal accumulation of seeds of green gram was higher than corn and the application of single fertilizer either farm yard manure (FYM) or nitrogen, phosphorous, and potassium (NPK) enhances the growth and yield of both the tolerant and sensitive plants in the mixed crop cultivations. PMID:25709647

  1. Urinary levels of nickel and chromium associated with dental restoration by nickel-chromium based alloys.

    Science.gov (United States)

    Chen, Bo; Xia, Gang; Cao, Xin-Ming; Wang, Jue; Xu, Bi-Yao; Huang, Pu; Chen, Yue; Jiang, Qing-Wu

    2013-03-01

    This paper aims to investigate if the dental restoration of nickel-chromium based alloy (Ni-Cr) leads to the enhanced excretions of Ni and Cr in urine. Seven hundred and ninety-five patients in a dental hospital had single or multiple Ni-Cr alloy restoration recently and 198 controls were recruited to collect information on dental restoration by questionnaire and clinical examination. Urinary concentrations of Ni and Cr from each subject were measure by graphite furnace atomic absorption spectrometry. Compared to the control group, the urinary level of Ni was significantly higher in the patient group of dental restoration. Potential short- and long-term effects of Ni-Cr alloy restoration need to be investigated.

  2. Primary and secondary crystallization of modified hypoeutectic chromium cast iron

    Directory of Open Access Journals (Sweden)

    A. Studnicki

    2010-04-01

    Full Text Available The paper presents investigations of crystallization of modified hypoeutectic wear resistant chromium cast iron which contains carbon about 2% and chromium on three levels (12%, 18% and 25%. Three substances were applied to the modification ( boron carbide (B4C, ferroniobium (FeNb and mixture of ferroniobium and mischmetal (RE. The investigations of crystallization were conducted the DTA method in DTA-C and DTA-Is testers. The influence on the course of the process of primary and secondary crystallization was observed.

  3. Use of chitosan for chromium removal from exhausted tanning baths.

    Science.gov (United States)

    Cesaro, Raffaele; Fabbricino, Massimiliano; Lanzetta, Rosa; Mancino, Anna; Naviglio, Biagio; Parrilli, Michelangelo; Sartorio, Roberto; Tomaselli, Michele; Tortora, Gelsomina

    2008-01-01

    A novel approach, based on chitosan heavy-metal sequestrating ability, is proposed for chromium(III) removal from spent tanning liquor. Experimental results, obtained at lab-scale using real wastewater, are presented and discussed. Resulting efficiencies are extremely high, and strongly dependent on chitosan dose and pH value. Comparative analyses with other polysaccharides is also carried out showing that amine groups are more efficient than carboxyl and sulphate ones. Chromium recovery from sorption complexes and chitosan regeneration is finally proposed to optimize the whole process.

  4. Water-Rock Interaction and the Hydrogeochemistry of Chromium in Groundwater from Multilevels Monitoring Wells in Urania, SP, Brazil

    OpenAIRE

    Reginaldo Antonio Bertolo; Leonardo Nobuo Oshima Marcolan; Christine Laure Marie Bourotte

    2009-01-01

    Anomalous natural concentrations of chromium, sometimes exceeding the potability limit (0.05 mg.L-1), have been detectedin the groundwater of Adamantina Aquifer in the municipality of Urânia, and in a wide region of the western part ofthe State of São Paulo. In order to identify the possible geochemical reactions that may explain the occurrence of chromiumin groundwater, chemical and mineralogical analyses were conducted in rock samples collected from deep boreholes drilledin the city of Urân...

  5. 47 CFR 54.405 - Carrier obligation to offer Lifeline.

    Science.gov (United States)

    2010-10-01

    ... (CONTINUED) UNIVERSAL SERVICE Universal Service Support for Low-Income Consumers § 54.405 Carrier obligation... service, as defined in § 54.401, to qualifying low-income consumers, and (b) Publicize the availability...

  6. 47 CFR 54.519 - State telecommunications networks.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 3 2010-10-01 2010-10-01 false State telecommunications networks. 54.519 Section 54.519 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES... telecommunications networks. (a) Telecommunications services. State telecommunications networks may secure...

  7. Preparation of Chromium Oxide Coatings on Aluminum Borate Whiskers by a Hydrothermal Deposition Process

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Aluminum borate whiskers (9Al2O32B2O3) can be used to reinforce aluminum alloys to produce light and strong composites. However, the adverse interfacial reactions between the whiskers and the aluminum alloys inhibit their practical uses; therefore, a protective coating is needed on whiskers. In this work, aluminum borate whiskers were coated with chromium-coating deposits in a hydrothermal solution containing CrCl3, Na2C4H4O6, NaPH2O2, and H3BO3. The presence of the impurity P in the hydrothermal deposits can be avoided by reducing the amount of NaPH2O2 in the coating solution. Thermodynamic analysis was used to discuss the behavior of ions in the coating process. The subsequent heating of the hydrothermal products in air at 800 ℃ yielded smooth Cr2O3 films with a thickness of 0.060.07 μm.

  8. A FACTORIAL DESIGN APPLIED TO THE STUDY OF CHROMIUM TOXICITY ON THE GLUTATHIONE LEVELS OF Brachiaria brizantha AND Brachiaria ruziziensis SEEDLINGS

    Directory of Open Access Journals (Sweden)

    Rafael Marques

    2015-08-01

    Full Text Available Chromium toxicity affects redox reactions within plant cells, generating detrimental reactive oxygen species. Glutathione is an antioxidant peptide and also a substrate for the production of phytochelatins, which are chelating peptides reported to mitigate Cr3+ toxicity in plants. In this study, Brachiaria brizantha (B. brizantha and Brachiaria ruziziensis (B. ruziziensis seedlings were evaluated for physiological responses and glutathione production following the addition of zero or 5 mg L-1 Cr3+ to the nutrient solution. Glutathione levels were determined by colorimetric analysis at 412 nm using 5,5'-dithio-bis(2-nitrobenzoic acid as a chromophore reagent and recovery with glutathione reductase (with evaluations at days 10 and 20 of continuous growth. The assessments were carried out in a completely randomized design with 2 authentic replications, and arranged in a 23 factorial. Cr3+ caused an average increase of 0.76 mg g-1 in the initial glutathione content. However, by day 20 there was an average reduction of 3.63 mg g-1. Chromium-affected physiological detrimental responses, albeit detected in both species, were less-pronounced in B. ruziziensis, along with a much higher level of glutathione. This study indicates that B. ruziziensis has a greater tolerance for chromium toxicity than B. brizantha, and that glutathione is likely to be involved in the mitigation of chromium stress in B. ruziziensis.

  9. The oxidation and reduction of chromium of stainless steels in an eletric arc furnace

    Directory of Open Access Journals (Sweden)

    B. Arh

    2011-07-01

    Full Text Available The oxidation of chromium during the elaboration of stainless steels occurs with oxygen in solution blown inthe melt and with oxides in the slag. A higher content of silicon in the furnace charge decreases the extent of oxidation of chromium, however, the efficient reduction of chromium from the slag is of essential importance for a minimal loss of chromium. In this survey, the theory of the oxidation of chromium, its reduction from the slag and the conditions for the formation of foaming slag are discussed.

  10. 46 CFR 111.54-3 - Remote control.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Remote control. 111.54-3 Section 111.54-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Circuit Breakers § 111.54-3 Remote control. Remotely controlled circuit breakers must have...

  11. 47 CFR 54.415 - Consumer qualification for Link Up.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 3 2010-10-01 2010-10-01 false Consumer qualification for Link Up. 54.415 Section 54.415 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES (CONTINUED) UNIVERSAL SERVICE Universal Service Support for Low-Income Consumers § 54.415...

  12. 29 CFR 70.54 - Employee Benefits Security Administration.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 1 2010-07-01 2010-07-01 true Employee Benefits Security Administration. 70.54 Section 70.54 Labor Office of the Secretary of Labor PRODUCTION OR DISCLOSURE OF INFORMATION OR MATERIALS Public Records and Filings § 70.54 Employee Benefits Security Administration. (a) The annual financial...

  13. 49 CFR 386.54 - Administrative Law Judge.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 5 2010-10-01 2010-10-01 false Administrative Law Judge. 386.54 Section 386.54... General Rules and Hearings § 386.54 Administrative Law Judge. (a) Powers of an Administrative Law Judge. The Administrative Law Judge may take any action and may prescribe all necessary rules and...

  14. 40 CFR 205.54-2 - Sound data acquisition system.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Sound data acquisition system. 205.54-2 Section 205.54-2 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) NOISE ABATEMENT PROGRAMS TRANSPORTATION EQUIPMENT NOISE EMISSION CONTROLS Medium and Heavy Trucks § 205.54-2...

  15. 19 CFR 151.54 - Testing by Customs laboratory.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 2 2010-04-01 2010-04-01 false Testing by Customs laboratory. 151.54 Section 151.54 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF... Other Metal-Bearing Materials § 151.54 Testing by Customs laboratory. Samples taken in accordance...

  16. 36 CFR 7.54 - Theodore Roosevelt National Park.

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 1 2010-07-01 2010-07-01 false Theodore Roosevelt National Park. 7.54 Section 7.54 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR SPECIAL REGULATIONS, AREAS OF THE NATIONAL PARK SYSTEM § 7.54 Theodore Roosevelt National Park....

  17. 30 CFR 47.54 - Availability of an MSDS.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Availability of an MSDS. 47.54 Section 47.54 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR EDUCATION AND TRAINING HAZARD COMMUNICATION (HazCom) Material Safety Data Sheets (MSDS) § 47.54 Availability of an MSDS. The operator must make MSDSs accessible to...

  18. 26 CFR 54.4980B-4 - Qualifying events.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 17 2010-04-01 2010-04-01 false Qualifying events. 54.4980B-4 Section 54.4980B... EXCISE TAXES (CONTINUED) PENSION EXCISE TAXES § 54.4980B-4 Qualifying events. The determination of what constitutes a qualifying event is addressed in the following questions and answers: Q-1: What is a...

  19. 9 CFR 54.3 - Animals eligible for indemnity payments.

    Science.gov (United States)

    2010-01-01

    ... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Animals eligible for indemnity payments. 54.3 Section 54.3 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE... SCRAPIE Scrapie Indemnification Program § 54.3 Animals eligible for indemnity payments. (a) Indemnity...

  20. 9 CFR 54.7 - Procedures for destruction of animals.

    Science.gov (United States)

    2010-01-01

    ... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Procedures for destruction of animals. 54.7 Section 54.7 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT... SCRAPIE Scrapie Indemnification Program § 54.7 Procedures for destruction of animals. (a)...

  1. 40 CFR 424.54-424.56 - [Reserved

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 28 2010-07-01 2010-07-01 true 424.54-424.56 Section 424.54-424.56 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS FERROALLOY MANUFACTURING POINT SOURCE CATEGORY Other Calcium Carbide Furnaces Subcategory §§ 424.54-424.56...

  2. 7 CFR 201.54 - Number of seeds for germination.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Number of seeds for germination. 201.54 Section 201.54... REGULATIONS Germination Tests in the Administration of the Act § 201.54 Number of seeds for germination. At least 400 seeds shall be tested for germination; except that in mixtures, 200 seeds of each of...

  3. 40 CFR 425.54 - New source performance standards (NSPS).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false New source performance standards (NSPS). 425.54 Section 425.54 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS LEATHER TANNING AND FINISHING POINT SOURCE CATEGORY No Beamhouse Subcategory § 425.54 New source performance standards...

  4. Friction and wear behavior of chromium carbide coatings

    International Nuclear Information System (INIS)

    Chromium carbides, tungsten carbide, and chromium oxide have been tested and evaluated as coatings to protect high-temperature gas-cooled reactor (HTGR) steam generator and other HTGR components from adhesion, galling associated with sliding wear or from fretting. Tests were performed in commercially-pure helium and in helium doped with various gaseous impurities (H2, H2O, CH4, CO) to simulate the primary coolant of an HTGR. Several types of chromium carbide coatings including Cr3C2, Cr7C3, and Cr23C6, were tested for wear resistance and resistance to long-term spalling. Tungsten carbide and chromium oxide coatings were tested in sliding wear tests. Cr23C6-NiCr coatings showed the best performance (from 400 to 8160C) whether they were applied by detonation gun or plasma gun spraying methods. The presence of the Cr23C6-NiCr coatings did not affect the creep rupture properties of Alloy 800H substrates at temperatures up to 7600C. Low-cycle fatigue life of similar specimens at 5930C was reduced to 10 to 20% when tested in the 1 to 0.6% strain range

  5. Porosity of detonation coatings on the base of chromium carbide

    International Nuclear Information System (INIS)

    Porosity of detonation coatings on the base of chromium carbide is estimated by the hydrostatic weighing. The open porosity value dependence on the distance of spraying, depth of the charge, ratio and volume of the detonator barrie filing with gas components is established. Pore distribution in the cross section of a specimen tested for porosity is studied by the methods of metallographic analysis

  6. Intestinal absorption of chromium as affected by wheat bran

    Energy Technology Data Exchange (ETDEWEB)

    Keim, K.S.; Holloway, C.L.; Hegsted, M.

    1986-03-01

    This study was designed to investigate the influence of dietary fiber, as found in wheat bran, on the absorption of chromium. Twenty male Sprague-Dawley rats were divided into two groups of 10. The control was fed a semi-purified diet containing casein, methionine, cornstarch, sucrose, corn oil, mineral and vitamin mix, and choline bitartrate. The experimental group was fed the same diet but with soft red winter wheat bran added to a level of 35% of the diet at the expense of sucrose. To determine chromium absorption and uptake by selected tissues, rats were fasted for 24 hr, fed 5 g of the respective diet, 2 hr later intubated with 100..mu..Ci of Cr-51of sacrificed 24 hr later. The rats wee housed in metabolic cages after the Cr-51 intubation. The addition of wheat brand to the diet did not significantly affect chromium absorption as measured by percent dose of Cr-51 in the 24 hr urine. The percent dose in the control group was 0.68 +/- 0.20% (mean +/- SEM) and in the experimental group 0.63 +/- 0.24% (mean +/-SEM) (N.S.). The cr-51 uptake of liver, spleen, jejunum, and blood was not statistically different between groups. These results indicate that dietary fiber as found in wheat bran does not impair intestinal absorption of chromium.

  7. Microbial biotechnology for remediation of aquatic habitats polluted with chromium

    Directory of Open Access Journals (Sweden)

    Viorica Coşier

    2008-12-01

    Full Text Available Chromium may occur in nine different forms of oxidation ranging from ?II to +VI, with forms II, III and VI as the most commonly encountered. In Cluj county, chromium pollution dates well back in time and has caused important dysfunction to the mechanical-biological wastewater purification station of the city of Cluj (Coşier & Diţă 1996. The purpose of this study was to develop one microbial method able to reduce hexavalent chromium (mobile, permeable to cell membrane, carcinogenic and mutagenic (Ishikawa et al 1994 to the trivalent form (insoluble and an essential element for humans (Song et al 2006. Different sources of chromium-reducing bacteria and many sources of carbon and energy added to the Kvasnikov mineral basal medium (Komori et al 1990 with increasing amount of chromate (200- 1000 mg/l were tested. Two bacterial strains, able to reduce even 1000 mg chromate/l, were isolated in pure culture. For one of these bacterial strains, we determined the optimum conditions for the reduction of Cr (VI.

  8. 75 FR 67100 - Superalloy Degassed Chromium From Japan

    Science.gov (United States)

    2010-11-01

    ... superalloy degassed chromium from Japan (70 FR 76030). The Commission is conducting a review to determine..., subparts A, D, E, and F (19 CFR part 207), as most recently amended at 74 FR 2847 (January 16, 2009). \\1... rule 201.15(b)(19 CFR 201.15(b)), 73 FR 24609 (May 5, 2008). This advice was developed in...

  9. 76 FR 8773 - Superalloy Degassed Chromium From Japan

    Science.gov (United States)

    2011-02-15

    ... applicable deadline.'' (75 FR 80457). Accordingly, pursuant to section 751(c) of the Tariff Act of 1930 (19 U... COMMISSION Superalloy Degassed Chromium From Japan AGENCY: United States International Trade Commission... Japan would be likely to lead to continuation or recurrence of material injury. On December 22,...

  10. Intestinal absorption of chromium as affected by wheat bran

    International Nuclear Information System (INIS)

    This study was designed to investigate the influence of dietary fiber, as found in wheat bran, on the absorption of chromium. Twenty male Sprague-Dawley rats were divided into two groups of 10. The control was fed a semi-purified diet containing casein, methionine, cornstarch, sucrose, corn oil, mineral and vitamin mix, and choline bitartrate. The experimental group was fed the same diet but with soft red winter wheat bran added to a level of 35% of the diet at the expense of sucrose. To determine chromium absorption and uptake by selected tissues, rats were fasted for 24 hr, fed 5 g of the respective diet, 2 hr later intubated with 100μCi of Cr-51of sacrificed 24 hr later. The rats wee housed in metabolic cages after the Cr-51 intubation. The addition of wheat brand to the diet did not significantly affect chromium absorption as measured by percent dose of Cr-51 in the 24 hr urine. The percent dose in the control group was 0.68 +/- 0.20% (mean +/- SEM) and in the experimental group 0.63 +/- 0.24% (mean +/-SEM) (N.S.). The cr-51 uptake of liver, spleen, jejunum, and blood was not statistically different between groups. These results indicate that dietary fiber as found in wheat bran does not impair intestinal absorption of chromium

  11. Invariant coefficients of diffusion in iron-chromium-nickel system

    Energy Technology Data Exchange (ETDEWEB)

    Mokrov, A.P.; Akimov, V.K.; Golubev, V.G.

    1984-02-01

    The temperature and concentration dependences of the Dsub(c) coefficients in the ..gamma..-phase of iron-chromium-nickel system are determined. It is proposed to described mutual diffusion in multicomponent systems using invariant, i.e. independent of the choice of solvent, coefficients of diffusion. The assumption that their temperature dependence follows the Arrhenius law is confirmed by the experiment.

  12. Invariant coefficients of diffusion in iron-chromium-nickel system

    International Nuclear Information System (INIS)

    The temperature and concentration dependences of the Dsub(c) coefficients in the γ-phase of iron-chromium-nickel system are determined. It is proposed to described mutual diffusion in mul-- ticomponent systems using invariant, i. e. independent of the choice of solvent, coefficients of diffusion. The assumption that their temperature dependence follows the Arrhenius law is confirmed by the experiment

  13. Differents remediation methodos for lead, chromium and cadmium contaminated soils

    International Nuclear Information System (INIS)

    The usage of phosphates in the remediation of plots contaminated with heavy metals appears to be a good strategy to lessen the danger of these metals. This study analyses the effect of the mobilization of: Lead, chromium and cadmium by utilizing diverse forms of phosphates in contaminated soils of three different origins with ph modification and without it

  14. IRIS TOXICOLOGICAL REVIEW OF HEXAVALENT CHROMIUM (INTERAGENCY SCIENCE CONSULTATION DRAFT)

    Science.gov (United States)

    On Septemeber 30, 2010, the draft Toxicological Review of Hexavalent Chromium and the charge to external peer reviewers were released for external peer review and public comment. The Toxicological Review and charge were reviewed internally by EPA and by other federal agenc...

  15. Chromium isotope fractionation during coprecipitation with calcium carbonate

    DEFF Research Database (Denmark)

    Rodler, Alexandra; Sánchez-Pastor, Nuria; Fernández-Díaz, Lurdes;

    The chromium (Cr) isotopic composition of carbonates can potentially be used as a paleoclimate proxy to elucidate past fluctuations of oxygen contents in atmosphere and hydrosphere. The use of Cr isotopes to track paleoenvironmental changes, for example related to the rise of oxygen during...

  16. Fractionation behavior of chromium isotopes during coprecipitation with calcium carbonate

    DEFF Research Database (Denmark)

    Rodler, Alexandra; Sánchez-Pastor, Nuria; Fernández-Díaz, Lurdes;

    2015-01-01

    Interest in chromium (Cr) isotope incorporation into carbonates arises from the observation that Cr isotopic composition of carbonates could be used as a paleoclimate proxy to elucidate past fluctuations of oxygen contents in atmosphere and hydrosphere. The use of Cr isotopes to track...

  17. Discovery of Chromium, Manganese, Nickel, and Copper Isotopes

    OpenAIRE

    Garofali, K.; Robinson, R; Thoennessen, M

    2010-01-01

    Twenty-seven chromium, twenty-five manganese, thirty-one nickel and twenty-six copper isotopes have so far been observed and the discovery of these isotopes is discussed. For each isotope a brief synopsis of the first refereed publication, including the production and identification method, is presented.

  18. Chromium stable isotope fractionation in modern biogeochemical cycling

    DEFF Research Database (Denmark)

    Paulukat, Cora Stefanie

    Chromium (Cr) is, due to its redox-sensitive properties, a powerful tracer for redox processes in environmental studies. Changes in its preferred oxidation state (III and VI) are accompanied by Crisotope fractionation. The Cr-isotope system is a promising tool to reconstruct the evolution of free...

  19. FEATURES OF CHROMIUM DOPING OF WEAR-RESISTANT CAST IRON

    Directory of Open Access Journals (Sweden)

    V. V. Netrebko

    2013-01-01

    Full Text Available The aim of this work analysis of the influence of chromium on the process of carbide formation, changes in chemical composition of the metal substrate in the areas adjacent to the carbides and at the hardness of iron while economy nickel and manganesealloying.

  20. Production performance of quails given chromium organic in ration

    Directory of Open Access Journals (Sweden)

    Deden Sudrajat

    2014-12-01

    Full Text Available Egg production of quails depends on quality of ration. Nutrient manipulation by chromiun inclusion in ration is a possible way to improve production. It is known that chromium mineral in form of GTF in blood has a role not only in enhancement of glucose entering cells through improvement of insulin activity but also in metabolism of lipid and synthesis of protein and elimination of heat stress to improve egg production. This study aimed at assessing egg production of quails fed ration containing chromium-yeast. Sixty-four quails aged 40 days were used. A completely randomized design with 4 treatments and 4 replication was applied in this study. Treatment consisted of commercial ration + Cr 0 ppm (R1, commercial ration + Cr 0.5 ppm (R2, commercial ration + Cr 1 ppm (R3, and commercial ration+ Cr 1.5 ppm (R4. Measurements were taken on feed intake, egg weight, egg mass production, hen day, feed conversion rate, egg index, and egg shell thickness. Results showed that A ration containing organic chromium as much as 1,5 ppm did not affect feed intake, egg production, egg weight, and eggshell thickness, however lowered feed conversion rate by up to 32.25% from that of control. Supplementation of 0,5 ppm chromium in the ration lowered the value of eggs index in the fourth week.

  1. Chromium toxicity to nitrifying bacteria: implications to wastewater treatment

    Science.gov (United States)

    Chromium, a heavy metal that enters wastewater treatment plants (WWTPs) through industrial discharges, can be toxic to microorganisms carrying out important processes within biological wastewater treatment systems. The effect of Cr(III) and Cr(VI) on ammonia dependent specific ox...

  2. DANGER OF HEXAVALENT CHROMIUM AND STRATEGY FOR THE REMEDITATION

    Directory of Open Access Journals (Sweden)

    Aniruddha Roy

    2013-02-01

    Full Text Available Some metals as micronutrients have a major role in the life and growth process of plants and animals. However, certain forms of some metals may also act as toxic material even in relatively small quantities. Chromium is such a metal, whose concentration above a certain limit may cause a serious problem to the health of living organisms. Chromium (Cr may occur in several chemical forms in organic and inorganic systems. In biological systems only Cr (III and Cr (VI are significant. Among these two states, trivalent chromium (Cr-III is considered as an essential component, while hexavalent Chromium (Cr-VI in biological system has been detected as responsible for so many diseases, even some specific forms of cancer. This paper intends to present the adverse effect of Cr(VI on environment as well as on human beings and also try to find a way out to dissolve the problem by a newly developed efficient and cost effective technique.

  3. Effects of chromium picolinate supplementation in type 2 diabetic patients

    Directory of Open Access Journals (Sweden)

    Niladê Rosinski Rocha

    2014-10-01

    Full Text Available The effects of chromium picolinate in Type 2 diabetic patients are investigated.  Seventeen Type 2 diabetic patients were randomly divided into two groups. The experimental group received fiber-rich hypocaloric diet and chromium picolinate whereas the control group received fiber-rich hypocaloric diet and placebo. The chromium picolinate was offered twice a day at the dose of 100 μg. Anthropometric data such as blood pressure, fasting glycemia and glycated hemoglobin (HbA1c were measured and these parameters were evaluated again after 90 days. No difference was reported in rates of body weight, waist, hip, body mass index, blood pressure and fasting glycemia (Control vs. Experimental groups after treatment. However, a decrease (p = 0.0405 of HbA1c occurred in the experimental group when the pre- and post-treatment rates were compared. HbA1c data showed that chromium picolinate improved the glycemic control in Type 2 diabetes.

  4. Determination of Chromium in Beef Heifers Nellore Supplemented with Chelate Chrome

    Directory of Open Access Journals (Sweden)

    P.S.A Moreira

    2013-11-01

    Full Text Available The objective of this work was to determine the amount of total chromium in beef heifers supplemented with chelated chromium in the rearing and finishing. We used 80 Nelore heifers at 12 months of age with mineral supplementation associated or not to chelate chromium, with average live weight of 220 kg. Were selected 36 heifer seach experimental group for analysis of meat samples. For the determination of chromium residue in the muscle tissue of the sample was1.5 g digested in a mixture of 5 ml 65% nitric acid and 1 ml of 30% hydrogen peroxide at 120° C for 12 hours block microdigestor. The total content of chromium was determined by spectrophotometry of atomic absorption flame. The experimental design was completely randomized and the results were analyzed by analysis of variance (ANOVA at 5% significance. It is concluded that the inclusion of chromium in the chelate heifers mineral supplementation increased the chromium content in the meat

  5. Contribution of photoelectron spectrometry and infrared spectrometry to the study of various oxidised forms of chromium

    International Nuclear Information System (INIS)

    Securate knowledge of internal surface of primary coolant circuits of PWR is required for an estimation of dissolution of used materials and for estimation of decontamination efficiency. The binding energies of various electron levels of chromium were determined by photoelectron spectrometry (ESCA), both for the metal and for certain compounds. Because of the intensities of the signals obtained the 2 p 3/2 level alone can be used for analytical purposes. Owing to a possible interference between this level due to hexavalent chromium and a satellite peak caused by trivalent chromium the method is not able to show up small amounts of chromium VI in chromium III. Simultaneous detection of the hexavalent and trivalent forms was achieved by infrared spectrometry. The problem of revealing traces of chromium VI in surface layers of trivalent chromium oxide has thus been solved

  6. Arsenic and chromium topsoil levels and cancer mortality in Spain.

    Science.gov (United States)

    Núñez, Olivier; Fernández-Navarro, Pablo; Martín-Méndez, Iván; Bel-Lan, Alejandro; Locutura, Juan F; López-Abente, Gonzalo

    2016-09-01

    Spatio-temporal cancer mortality studies in Spain have revealed patterns for some tumours which display a distribution that is similar across the sexes and persists over time. Such characteristics would be common to tumours that shared risk factors, including the chemical soil composition. The objective of the present study is to assess the association between levels of chromium and arsenic in soil and the cancer mortality. This is an ecological cancer mortality study at municipal level, covering 861,440 cancer deaths in 7917 Spanish mainland towns from 1999 to 2008. Chromium and arsenic topsoil levels (partial extraction) were determined by ICP-MS at 13,317 sampling points. To estimate the effect of these concentrations on mortality, we fitted Besag, York and Mollié models, which included, as explanatory variables, each town's chromium and arsenic soil levels, estimated by kriging. In addition, we also fitted geostatistical-spatial models including sample locations and town centroids (non-aligned data), using the integrated nested Laplace approximation (INLA) and stochastic partial differential equations (SPDE). All results were adjusted for socio-demographic variables and proximity to industrial emissions. The results showed a statistical association in men and women alike, between arsenic soil levels and mortality due to cancers of the stomach, pancreas, lung and brain and non-Hodgkin's lymphomas (NHL). Among men, an association was observed with cancers of the prostate, buccal cavity and pharynx, oesophagus, colorectal and kidney. Chromium topsoil levels were associated with mortality among women alone, in cancers of the upper gastrointestinal tract, breast and NHL. Our results suggest that chronic exposure arising from low levels of arsenic and chromium in topsoil could be a potential risk factor for developing cancer.

  7. Sorption of chromium in soils of the Cerrado Goias, Brazil

    Directory of Open Access Journals (Sweden)

    Welershon José de Castro

    2010-08-01

    Full Text Available Land application of tannery sludge, which usually contain high levels of chromium, and considerable amounts of organic matter, macronutrients and micronutrients may contribute to the improvement of soil fertility and plant nutrition, and constitutes a form of disposal residue in the environment. The objective of this work was to determine the sorption isotherms of metal chromium (Cr+3 in a Ultisol, Oxisol Typic Acrustox, Quartzipsamment and Kandic Oxisol, identify soil classes that are prone to chromium mobility, and characterize the potential of agricultural soils of Goiás that are subject to groundwater contamination by the potentially toxic metal. For the establishment of sorption isotherms, solutions were prepared at 1:10 in volume. Air dried samples of 5.0 cm3 of each class of soil were placed in triplicates in beakers of 250.0 cm3. A solution containing 50.0 cm3 of the potentially toxic metal was added to solution. The solutions were prepared in CaCl2.(2H2O (0.01 mol.L-1 as electrolyte support and employing the basic chromium sulphate as a source of metal. Adjustments were made to the polynomial regression between the concentrations of potentially toxic levels of metal contaminants in the solution depending on the concentration of metal in the filtered solution after equilibrium. The Quartzipsamment showed lower retention compared to other classes of soils. Therefore it is more vulnerable to groundwater contamination if industrial wastes containing trivalent chromium are used as fertilizer.

  8. Analysis list: lin-54 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available lin-54 Larvae + ce10 http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/target/lin-54....1.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/target/lin-54.5.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/target/lin...-54.10.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/colo/lin-54.Larvae.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/colo/Larvae.gml ...

  9. in 54 Mother-Child Dyads

    Directory of Open Access Journals (Sweden)

    Helene Werner

    2011-01-01

    Full Text Available This study describes parental expectations for sleep-wake patterns in healthy kindergarten children and explores their relation to children’s sleep quality and parental distress. Data analysis of 54 mother-child dyads (age range of the children: 4–7 years indicated that parental expectations for children’s sleep-wake patterns differ between scheduled and free days and depend on children’s chronotype. Mothers of children with late chronotype showed less adequate expectations for children’s sleep onset time than mothers of children with early chronotype (e.g., morning types. Furthermore, children of mothers with less adequate expectations for children’s sleep onset time on scheduled days had longer settling periods during which sleep rituals may take place (r=0.31, P≤0.05, spent more time in bed than they actually sleep (r=0.35, P≤0.01, and had more frequently difficulties falling asleep (r=0.33, P≤0.01. However, less adequate expectations for children’s sleep onset time were not associated with parental distress (P>0.05. We conclude that parental expectations about their children’s sleep play a key role in understanding normal and abnormal sleep during childhood.

  10. Resultados da microcirurgia em 54 aneurismas intracranianos

    Directory of Open Access Journals (Sweden)

    Paulo Niemeyer

    1974-09-01

    Full Text Available O autor apresenta sua experiência em 54 aneurismas arteriais intracranianos operados com técnica microcirúrgica, no período de janeiro de 1971 a março de 1974. Em 40 doentes classificados nos grupos I, II e III, não houve mortalidade. Incluindo 8 doentes do grupo IV, onde ocorreram 3 óbitos, a mortalidade foi de 6,2%. Nos doentes do grupo V, a mortalidade continua proibitiva, seja qual for a técnica usada. Os doentes foram operados com microscópio cirúrgico de fabricação brasileira, sendo usados clips de Yasargil, Scoville, Mayfield e de modelo do autor. Comparando os resultados atuais de microcirurgia (1971-1974, com a experiência anterior, baseada em cerca de 400 casos, no período de 1949 a 1970, o autor conclui que a cirurgia dos aneurismas com auxílio do microscópio é benigna e sem mortalidade nos doentes de bom risco cirúrgico. Considera a existência de espasmo o maior problema e julga que o momento mais oportuno de operar é quando surgem as melhoras clínicas, coincidindo com o desaparecimento do espasmo, entre o 7º e 10º dia, geralmente.

  11. Chromium, chromium isotopes and selected trace elements, western Mojave Desert, USA

    Energy Technology Data Exchange (ETDEWEB)

    Izbicki, John A. [U.S. Geological Survey, 4165 Spruance Road, Suite O, San Diego, CA 92123 (United States)], E-mail: jaizbick@usgs.gov; Ball, James W. [U.S. Geological Survey, 3215 Marine Street, Boulder, Colorado, CO 80303 (United States); Bullen, Thomas D. [U.S. Geological Survey, 345 Middlefield Road, Building 15, McKelvey Building, MS-420, Menlo Park, CA 94025 (United States); Sutley, Stephen J. [Denver Federal Center, P.O. Box 25046, MS-964, Denver, CO 80225-0046 (United States)

    2008-05-15

    Chromium(VI) concentrations in excess of the California Maximum Contaminant Level (MCL) of 50 {mu}g/L occur naturally in alkaline, oxic ground-water in alluvial aquifers in the western Mojave Desert, southern California. The highest concentrations were measured in aquifers eroded from mafic rock, but Cr(VI) as high as 27 {mu}g/L was measured in aquifers eroded from granitic rock. Chromium(VI) concentrations did not exceed 5 {mu}g/L at pH < 7.5 regardless of geology. {delta}{sup 53}Cr values in native ground-water ranged from 0.7 to 5.1 per mille and values were fractionated relative to the average {delta}{sup 53}Cr composition of 0 per mille in the earth's crust. Positive {delta}{sup 53}Cr values of 1.2 and 2.3 per mille were measured in ground-water recharge areas having low Cr concentrations, consistent with the addition of Cr(VI) that was fractionated on mineral surfaces prior to entering solution. {delta}{sup 53}Cr values, although variable, did not consistently increase or decrease with increasing Cr concentrations as ground-water flowed down gradient through more oxic portions of the aquifer. However, increasing {delta}{sup 53}Cr values were observed as dissolved O{sub 2} concentrations decreased, and Cr(VI) was reduced to Cr(III), and subsequently removed from solution. As a result, the highest {delta}{sup 53}Cr values were measured in water from deep wells, and wells in discharge areas near dry lakes at the downgradient end of long flow paths through alluvial aquifers. {delta}{sup 53}Cr values at an industrial site overlying mafic alluvium having high natural background Cr(VI) concentrations ranged from -0.1 to 3.2 per mille . Near zero {delta}{sup 53}Cr values at the site were the result of anthropogenic Cr. However, mixing with native ground-water and fractionation of Cr within the plume increased {delta}{sup 53}Cr values at the site. Although {delta}{sup 53}Cr was not necessarily diagnostic of anthropogenic Cr, it was possible to identify the extent

  12. Raman spectroscopy of supported chromium oxide catalysts : determination of chromium-oxygen bond distances and bond orders

    NARCIS (Netherlands)

    Weckhuysen, B.M.; Wachs, I.E.

    1996-01-01

    An empirical correlation is described for relating Raman stretching frequencies of chromium—oxygen (Cr—O) bonds to their bond lengths in chromium oxide reference compounds. An exponential fit of crystallographically determined Cr—O bond lengths to Cr—O Raman symmetric stretching frequencies (800–130

  13. Reduction of hexavalent chromium by ferrous iron: A process of chromium isotope fractionation and its relevance to natural environments

    DEFF Research Database (Denmark)

    Døssing, Lasse Nørbye; Dideriksen, Knud; Stipp, Susan Louise Svane;

    2011-01-01

    Stable chromium (Cr) isotopes can be used as a tracer for changing redox conditions in modern marine systems and in the geological record. We have investigated isotope fractionation during reduction of Cr(VI)aq by Fe(II)aq. Reduction of Cr(VI)aq by Fe(II)aq in batch experiments leads to significant...

  14. Activated carbon adsorption for chromium treatment and recovery; Adsorbimento di cromo su carboni attivi a scopo di recupero e decontaminazione

    Energy Technology Data Exchange (ETDEWEB)

    Baroncelli, F.; Castelli, S.; De Francesco, M. [ENEA, Casaccia (Italy). Area Energia e Innovazione

    1994-05-01

    The capability of actived carbon systems to adsorb chromium from wastewater of galvanic industry is valued. Batch tests and column tests are carried out with good results. An activated carbon with acidic surface oxides can adsorb both chromate and chromium (III); chromate is reduced in situ and then adsorbed as chromium (III). Chromium can be desorbed from carbon by an acid or basic treatment obtaining respectively chromium (III) or chromate solutions. Carbon can be regenerated many times without evident signs of deterioration.

  15. The effect of dietary supplementation with different forms and levels of organic chromium on broilers meat quality

    OpenAIRE

    Keleman Svetlana P.; Kevrešan Slavko E.; Supić Boriša; Perić Lidija; Strugar Vladimir

    2006-01-01

    This paper deals with the effect of supplementation with the three different preparations of organic chromium complexes: the ethylenediaminetetraacetic acid complex with chromium; chromium (III)­lysine and chromium picolinate, on broilers meat quality. In every preparation supplementing broilers diet chromium was present at the three different levels: 0.2; 0.4 and 0.6 mg/kg. The meat quality was monitored with respect to the following parameters: the contents of fat, protein, minerals and wat...

  16. Radiative proton capture cross sections in the mass range 40-54

    Science.gov (United States)

    Chakraborty, Dipti; Dutta, Saumi; Gangopadhyay, G.; Bhattacharyya, Abhijit

    2016-07-01

    Proton capture cross sections in the energy range of astrophysical interest for mass region 40-54 have been calculated in the Hauser-Feshbach formalism with the reaction code talys1.6. The density-dependent M3Y effective nucleon-nucleon interaction folded with target radial matter densities from the relativistic mean field approach is used to obtain the semimicroscopic optical potential. A definite normalization of potential well depths has been used over the entire mass region. The (p ,γ ) rates of some reactions, important in the astrophysical scenario, are calculated using the potential in the relevant mass region.

  17. Effect of recasting on the thickness of metal-ceramic interface of nickel-chromium and cobalt-chromium alloys

    Directory of Open Access Journals (Sweden)

    Mirković Nemanja

    2008-01-01

    Full Text Available Introduction/Aim. This research was done to establish recasting effects of nickel-chromium and cobalt-chromium alloys on the thickness of their metal-ceramic interface in making fixed partial dentures. Metal-ceramic interface determines their functional integrity and prevents damages on ceramics during mastication. Investigation of metal-ceramic samples is supposed to show if base metal alloys for metalceramics are successfully recycled without any risk of reduction of metal-ceramic interface thickness. Methods. The research was performed as an experimental study. Per six metal-ceramic samples of nickel-chromium alloy (Wiron99 and cobalt-chromium alloy (Wirobond C were made each. Alloy residues were recycled through twelve casting generations with the addition of 50% of new alloy on the occasion of every recasting. Analysis Energy Dispersive X-ray (EDX (Oxford Instruments and Scanning Electon Microscop (SEM analysis (JEOL were used to determine thickness of metal-ceramic interface together with PC Software for quantification of visual information's (KVI POPOVAC. Results. Results of this research introduced significant differences between thickness of metal-ceramic interface in every examined recycle generation. Recasting had negative effect on thickness of metal-ceramic interface of the examined alloys. This research showed almost linear reduction of elastic modulus up to the 12th generation of recycling. Conclusion. Recasting of nickel-chromium and cobaltchromium alloys is not recommended because of reduced thickness of metal-ceramic interface of these alloys. Instead of recycling, the alloy residues should be returned to the manufacturers.

  18. Bioadsorption and bioaccumulation of chromium trivalent in Cr(III)-tolerant microalgae: a mechanisms for chromium resistance.

    Science.gov (United States)

    Pereira, M; Bartolomé, M C; Sánchez-Fortún, S

    2013-10-01

    Anthropogenic activity constantly releases heavy metals into the environment. The heavy metal chromium has a wide industrial use and exists in two stable oxidation states: trivalent and hexavalent. While hexavalent chromium uptake in plant cells has been reported that an active process by carrying essential anions, the cation Cr(III) appears to be taken up inactively. Dictyosphaerium chlorelloides (Dc1M), an unicellular green alga is a well-studied cell biological model organism. The present study was carried out to investigate the toxic effect of chromium exposures on wild-type Cr(III)-sensitive (Dc1M(wt)) and Cr(III)-tolerant (Dc1M(Cr(III)R30)) strains of these green algae, and to determine the potential mechanism of chromium resistance. Using cell growth as endpoint to determine Cr(III)-sensitivity, the IC₅₀(₇₂) values obtained show significant differences of sensitivity between wild type and Cr(III)-tolerant cells. Scanning electron microscopy (SEM) showed significant morphological differences between both strains, such as decrease in cell size or reducing the coefficient of form; and transmission electron microscopy (TEM) revealed ultrastructural changes such as increased vacuolization and cell wall thickening in the Cr(III)-tolerant strain with respect to the wild-type strain. Energy dispersive X-ray analysis (SEM/XEDS) revealed that Cr(III)-tolerant D. chlorelloides cells are able to accumulate considerable amounts of chromium distributed in cell wall (bioadsorption) as well as in cytoplasm, vacuoles, and chloroplast (bio-accumulation). Morphological changes of Cr(III)-tolerant D. chlorelloides cells and the presence of these electron-dense bodies in their cell structures can be understood as a Cr(III) detoxification mechanism. PMID:23810518

  19. Chromium(VI) but not chromium(III) species decrease mitoxantrone affinity to DNA.

    Science.gov (United States)

    Nowicka, Anna M; Stojek, Zbigniew; Hepel, Maria

    2013-01-31

    Binding of mitoxantrone (MXT) to double-stranded DNA has been investigated as a model drug-DNA binding system to evaluate the effects of various forms of chromium on the binding properties. We have found that Cr(III), which binds strongly to DNA, does not affect the MXT affinity to DNA. In contrast, Cr(VI), in the form of chromate ions CrO(4)(2-), decreases the MXT affinity to DNA despite electrostatic repulsions with phosphate-deoxyribose chains of DNA. The MXT-DNA binding constant was found to decrease from (1.96 ± 0.005) × 10(5) to (0.77 ± 0.018) × 10(5) M(-1) for Cr(VI) concentration changing from 0 to 30 μM. The influence of Cr(VI) on MXT-DNA binding has been attributed to the oxidation of guanine residue, thus interrupting the intercalation of MXT into the DNA double helix at the preferential CpG intercalation site. This supposition is corroborated by the observed increase in the MXT binding site size from 2 bp (base pairs) to 4-6 bp in the presence of Cr(VI). The measurements of the MXT-DNA binding constant and the MXT binding site size on a DNA molecule have been carried out using spectroscopic, voltammetric, and nanogravimetric techniques, providing useful information on the mechanism of the interactions.

  20. Urinary levels of nickel and chromium associated with dental restoration by nickel-chromium based alloys

    Institute of Scientific and Technical Information of China (English)

    Bo Chen; Gang Xia; Xin-Ming Cao; Jue Wang; Bi-Yao Xu; Pu Huang; Yue Chen; Qing-Wu Jiang

    2013-01-01

    This paper aims to investigate if the dental restoration of nickel-chromium based alloy (Ni-Cr) leads to the enhanced excretions of Ni and Cr in urine. Seven hundred and ninety-five patients in a dental hospital had single or multiple Ni-Cr alloy restoration recently and 198 controls were recruited to collect information on dental restoration by questionnaire and clinical examination. Urinary concentrations of Ni and Cr from each subject were measure by graphite furnace atomic absorption spectrometry. Compared to the control group, the urinary level of Ni was significantly higher in the patient group of 〈 1 month of the restoration duration, among which higher Ni excretions were found in those with either a higher number of teeth replaced by dental alloys or a higher index of metal crown not covered with the porcelain. Urinary levels of Cr were significantly higher in the three patient groups of 〈1, 1 to 〈3 and 3 to 〈6 months, especially in those with a higher metal crown exposure index. Linear curve estimations showed better relationships between urinary Ni and Cr in patients within 6-month groups. Our data suggested significant increased excretions of urinary Ni and Cr after dental restoration. Potential short- and long-term effects of Ni-Cr alloy restoration need to be investigated.

  1. A computational investigation of boron-doped chromium and chromium clusters by density functional theory

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    The geometries,stabilities and electronic properties of Crn and CrnB(n=2-9) clusters have been systematically investigated by density functional theory.The results suggest that the lowest energy structures for CrnB clusters can be obtained by substituting one Cr atom in Crn+1 clusters with B atom.The geometries of CrnB clusters are similar to that of Crn+1 clusters except for local structural distortion.The second-order difference and fragmentation energy show Cr4,Cr6,Cr8,Cr3B,Cr5B and Cr8B cluster are the most stable among these studied clusters.The impurity B increases the stabilities of chromium cluster.When B is doped on the Crn clusters,cluster geometry does dominate positive role in enhancing their stability.The doped B atom does not change the coupling way of the Cr site in Crn clusters,but breaks the symmetry and the Cr atoms are no longer equivalent.The doped B atom increases the total magnetic moments of Crn in most cases.

  2. A metastable chromium carbide powder obtained by carburization of a metastable chromium oxide

    Energy Technology Data Exchange (ETDEWEB)

    Loubiere, S. [Univ. Paul-Sabatier, Toulouse (France). Lab. de Chimie des Materiaux Inorganique; Laurent, C. [Univ. Paul-Sabatier, Toulouse (France). Lab. de Chimie des Materiaux Inorganique; Bonino, J.P. [Univ. Paul-Sabatier, Toulouse (France). Lab. de Chimie des Materiaux Inorganique; Rousset, A. [Univ. Paul-Sabatier, Toulouse (France). Lab. de Chimie des Materiaux Inorganique

    1996-10-15

    A metastable Cr{sub 3}C{sub 2-x} carbide powder is prepared by carburization of a metastable chromium oxide in H{sub 2}-CH{sub 4} atmosphere under the appropriate conditions (temperature, dwell time and CH{sub 4} content). A very high specific surface area (greater than 210 m{sup 2} g{sup -1}) of the starting oxide is necessary to avoid the formation of the sole stable Cr{sub 3}C{sub 2} phase. The transformation from the stable Cr{sub 3}C{sub 2} to the metastable Cr{sub 3}C{sub 2-x} is observed for the first time. The driving force could be an epitaxial effect between Cr{sub 3}C{sub 2-x} and the surrounding graphite layer. This is consistent with the observation that the formation of graphite layers by CH{sub 4} cracking is easier in the Cr{sub 3}C{sub 2-x}-containing powders. (orig.)

  3. STS-54 Space Shuttle mission report

    Science.gov (United States)

    Fricke, Robert W., Jr.

    1993-03-01

    The STS-54 Space Shuttle Program Mission Report is a summary of the Orbiter, External Tank (ET), Solid Rocket Booster/Redesigned Solid Rocket Motor (SRB/RSRM), and the Space Shuttle Main Engine (SSME) subsystems performance during this fifty-third flight of the Space Shuttle Program, and the third flight of the Orbiter vehicle Endeavour (OV-105). In addition to the Orbiter, the flight vehicle consisted of an ET, which was designated ET-51; three SSME's, which were serial numbers 2019, 2033, and 2018 in positions 1, 2, and 3, respectively; and two retrievable and reusable SRB's which were designated BI-056. The lightweight RSRM's that were installed in each SRB were designated 360L029A for the left SRB, and 360L029B for the right SRB. The primary objectives of this flight were to perform the operations to deploy the Tracking and Data Relay Satellite-F/Inertial Upper Stage payload and to fulfill the requirements of the Diffuse X-Ray Spectrometer (DXS) payload. The secondary objective was to fly the Chromosome and Plant Cell Division in Space (CHROMEX), Commercial Generic Bioprocessing Apparatus (CGBA), Physiological and Anatomical Rodent Experiment (PARE), and the Solid Surface Combustion Experiment (SSCE). In addition to presenting a summary of subsystem performance, this report also discusses each Orbiter, ET, SSME, SRB, and RSRM in-flight anomaly in the applicable section of the report. The official tracking number for each in-flight anomaly, assigned by the cognizant project, is also shown. All times are given in Greenwich mean time (G.m.t.) and mission elapsed time (MET).

  4. Lead-chromium carbonyl complexes incorporated with group 8 metals: synthesis, reactivity, and theoretical calculations.

    Science.gov (United States)

    Shieh, Minghuey; Chu, Yen-Yi; Hsu, Miao-Hsing; Ke, Wei-Ming; Lin, Chien-Nan

    2011-01-17

    The trichromium-lead complex [Pb{Cr(CO)5}3](2-) (1) was isolated from the reaction of PbCl2 and Cr(CO)6 in a KOH/MeOH solution, and the new mixed chromium-iron-lead complex [Pb{Cr(CO)5}{Fe(CO)4}2](2-) (3) was synthesized from the reaction of PbCl2 and Cr(CO)6 in a KOH/MeOH solution followed by the addition of Fe(CO)5. X-ray crystallography showed that 3 consisted of a central Pb atom bound in a trigonal-planar environment to two Fe(CO)4 and one Cr(CO)5 fragments. When complex 1 reacted with 1.5 equiv of Mn(CO)5Br, the Cr(CO)4-bridged dimeric lead-chromium carbonyl complex [Pb2Br2Cr4(CO)18](2-) (4) was produced. However, a similar reaction of 3 or the isostructural triiron-lead complex [Pb{Fe(CO)4}3](2-) (2) with Mn(CO)5Br in MeCN led to the formation of the Fe3Pb2-based trigonal-bipyramidal complexes [Fe3(CO)9{PbCr(CO)5}2](2-) (6) and [Fe3(CO)9{PbFe(CO)4}2](2-) (5), respectively. On the other hand, the Ru3Pb2-based trigonal-bipyramidal complex [Ru3(CO)9{PbCr(CO)5}2](2-) (7) was obtained directly from the reaction of PbCl2, Cr(CO)6, and Ru3(CO)12 in a KOH/MeOH solution. X-ray crystallography showed that 5 and 6 each had an Fe3Pb2 trigonal-bipyramidal core geometry, with three Fe(CO)3 groups occupying the equatorial positions and two PbFe(CO)4 or PbCr(CO)5 units in the axial positions, while 7 displayed a Ru3Pb2 trigonal-bipyramidal geometry with three equatorial Ru(CO)3 groups and two axial PbCr(CO)5 units. The complexes 3-7 were characterized spectroscopically, and their nature, formation, and electrochemistry were further examined by molecular orbital calculations at the B3LYP level of density functional theory.

  5. A Study of the High Temperature on Chromium Carbide

    International Nuclear Information System (INIS)

    The oxidation rates of chromium carbide have been measured at 900 to 1300 .deg. C and oxygen pressures between 2x10-2 8 x 10-2 Pa using thermogravimetric analysis method. Oxidation behavior of chromium carbide appeared to change very sensitively with both temperature and oxygen pressure. In case with the oxygen pressure lower than 8 x 10-2 Pa, the weight gain in the specimen due to the formation of chromium oxide occurred linearly with time at the every temperature studied, but when the oxygen pressure was increased up to 8 x 10-2Pa, the weight gain behavior versus time showed entirely different tendency. That is, in the temperature range of 900 .deg. C to 1000 .deg. C weight gain occurred, however in the range of 1000 .deg. C to 1300 .deg. C weight lost was observed. The reason for the observed linear kinetics could be inferred as follows. As the oxidation of carbide proceeded carbon monoxide would build up at the interface of the chromium oxide and carbide. If the equilibrium pressure of carbon monoxide at the interface exceeds the gas pressure at the outer specimen surface, the oxide scale formed on it might be cracked exposing new carbide sites on which oxidation could occur successively. Through a thermodynamic consideration it was judged that the above deduction was reasonable. On the other hand, the weight lost mentioned above was explained that it could occur mainly due to the further oxidation of Cr2O3 to the volatile CrO3 at the corresponding experimental conditions. Weight loss phenomenon mentioned before which was observed in the oxidation of chromium carbide was also clearified by X-ray diffraction method and SEM. That is, at 900 .deg. C stable oxide of chromium, (Cr2O3) was identified easily on the specimen surface. However, at 1300 .deg. C, only a few amount of this stable oxide could be found on to specimen surface, indicating Cr2O3 had been evaporated to CrO3 gas

  6. Application of high performance liquid chromatography with inductively coupled plasma mass spectrometry (HPLC-ICP-MS) for determination of chromium compounds in the air at the workplace.

    Science.gov (United States)

    Stanislawska, Magdalena; Janasik, Beata; Wasowicz, Wojciech

    2013-12-15

    The toxicity and bioavailability of chromium species are highly dependable on the form or species, therefore determination of total chromium is insufficient for a complete toxicological evaluation and risk assessment. An analytical method for determination of soluble and insoluble Cr (III) and Cr (VI) compounds in welding fume at workplace air has been developed. The total chromium (Cr) was determined by using quadruple inductively coupled plasma mass spectrometry (ICP-MS) equipped with a dynamic reaction cell (DRC(®)). Soluble trivalent and hexavalent chromium compounds were determined by high performance liquid chromatography with inductively coupled plasma mass spectrometry (HPLC-ICP-MS). A high-speed, reversed-phase CR C8 column (PerkinElmer, Inc., Shelton, CT, USA) was used for the speciation of soluble Cr (III) and soluble Cr (VI). The separation was accomplished by interaction of the chromium species with the different components of the mobile phase. Cr (III) formed a complex with EDTA, i.e. retained on the column, while Cr (VI) existed in the solutions as dichromate. Alkaline extraction (2% KOH and 3% Na2CO3) and anion exchange column (PRP-X100, PEEK, Hamilton) were used for the separation of the total Cr (VI). The results of the determination of Cr (VI) were confirmed by the analysis of the certified reference material BCR CRM 545 (Cr (VI) in welding dust). The results obtained for the certified material (40.2±0.6 g kg(-1)) and the values recorded in the examined samples (40.7±0.6 g kg(-1)) were highly consistent. This analytical method was applied for the determination of chromium in the samples in the workplace air collected onto glass (Whatman, Ø 37 mm) and membrane filters (Sartorius, 0.8 μm, Ø 37 mm). High performance liquid chromatography with inductively coupled plasma mass spectrometry is a remarkably powerful and versatile technique for determination of chromium species in welding fume at workplace air. PMID:24209303

  7. Finished leather waste chromium acid extraction and anaerobic biodegradation of the products.

    Science.gov (United States)

    Ferreira, Maria J; Almeida, Manuel F; Pinho, Sílvia C; Santos, Isabel C

    2010-06-01

    Due to the amounts of chromium in the leachate resulting from leather leaching tests, chromium sulfate tanned leather wastes are very often considered hazardous wastes. To overcome this problem, one option could be recovering the chromium and, consequently, lowering its content in the leather scrap. With this objective, chromium leather scrap was leached with sulfuric acid solutions at low temperature also aiming at maximizing chromium removal with minimum attack of the leather matrix. The effects of leather scrap dimension, sulfuric acid and sodium sulfate concentration in the solutions, as well as extraction time and temperature on chromium recovery were studied, and, additionally, organic matrix degradation was evaluated. The best conditions found for chromium recovery were leather scrap conditioning using 25mL of concentrated H(2)SO(4)/L solution at 293 or 313K during 3 or 6days. Under such conditions, 30-60+/-5% of chromium was recovered and as low as 3-6+/-1% of the leather total organic carbon (TOC) was dissolved. Using such treatment, the leather scrap area and volume are reduced and the residue is a more brittle material showing enhanced anaerobic biodegradability. Although good recovery results were achieved, due to the fact that the amount of chromium in eluate exceeded the threshold value this waste was still hazardous. Thus, it needs to be methodically washed in order to remove all the chromium de-linked from collagen.

  8. Investigation of the surface composition of electrodeposited black chromium by X-ray photoelectron spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Survilienė, S., E-mail: sveta@ktl.mii.lt; Češūnienė, A.; Jasulaitienė, V.; Jurevičiūtė, I.

    2015-01-01

    Highlights: • Black chromium electrodeposited from a Cr(III) bath is composed of oxide, hydroxide and metallic chromium. • Metallic phase is absent in black chromium electrodeposited from a Cr(III) + ZnO bath. • The near-surface layer is rich in hydroxides, whereas oxides of both metals predominate in the depth of the coatings. - Abstract: The paper reviews black chromium electrodeposited from a trivalent chromium bath containing ZnO as a second main component. The chemical compositions of the top layers of the black chromium coatings were studied by the X-ray photoelectron spectroscopy method. The surface of black chromium was found to be almost entirely covered with organic substances. To gain information on the state of each element in the deposit bulk, the layer-by-layer etching of the black chromium surface with argon gas was used. Analysis of XPS spectra has shown that the top layers of black chromium without zinc are composed of various Cr(III) components, organic substances and metallic Cr, whereas metallic Cr is almost absent in black chromium containing some amount of Zn(II) compounds. The ratios of metal/oxide phases were found to be 10/27 and 2/28 for black chromium without and with zinc, respectively. It has been determined that owing to the presence of ZnO in the Cr(III) bath, the percentage of metallic chromium is substantially reduced in black chromium which is quite important for good solar selective characteristics of the coating. The results confirm some of earlier observations and provide new information on the composition of the near-surface layers.

  9. Investigation of the surface composition of electrodeposited black chromium by X-ray photoelectron spectroscopy

    International Nuclear Information System (INIS)

    Highlights: • Black chromium electrodeposited from a Cr(III) bath is composed of oxide, hydroxide and metallic chromium. • Metallic phase is absent in black chromium electrodeposited from a Cr(III) + ZnO bath. • The near-surface layer is rich in hydroxides, whereas oxides of both metals predominate in the depth of the coatings. - Abstract: The paper reviews black chromium electrodeposited from a trivalent chromium bath containing ZnO as a second main component. The chemical compositions of the top layers of the black chromium coatings were studied by the X-ray photoelectron spectroscopy method. The surface of black chromium was found to be almost entirely covered with organic substances. To gain information on the state of each element in the deposit bulk, the layer-by-layer etching of the black chromium surface with argon gas was used. Analysis of XPS spectra has shown that the top layers of black chromium without zinc are composed of various Cr(III) components, organic substances and metallic Cr, whereas metallic Cr is almost absent in black chromium containing some amount of Zn(II) compounds. The ratios of metal/oxide phases were found to be 10/27 and 2/28 for black chromium without and with zinc, respectively. It has been determined that owing to the presence of ZnO in the Cr(III) bath, the percentage of metallic chromium is substantially reduced in black chromium which is quite important for good solar selective characteristics of the coating. The results confirm some of earlier observations and provide new information on the composition of the near-surface layers

  10. Hyperfine field on Fe, Rh, Cd and Sn nucleus probes in chromium host

    Directory of Open Access Journals (Sweden)

    S. Sirousi

    2005-03-01

    Full Text Available   The incommensurate spin -density –wave magnetism of Cr has attracted great interest since its discovery via neutron scattering. Although the existence of spin- density –wave has been confirmed by experiment but the calculations which have been carried out have not been able to predict the correct ground state magnetic phase for chromium yet. To predict the magnetic hyperfine field at nucleus of different impurities in Cr host, we calculated the hyperfine field on Cd, Sn, Rh and Fe probes in the first step. Our calculations were performed within the framework of density functional theory, using the full-potential-linearized augmented plane-wave method. We used a supercell constructed from 8 bcc unit cells with impurity concentratin of 6.25 % and to analysise the supercell size effect on different magnetic quantities we repeated our calculation using a supercell with 54 atoms. The result of this effort showed that the magnetic hyperfine field and magnetic moment of nearesrt Cr is very little influenced by the size of supercell, so we can calculate the magnetic hyperfine field if it’s quantity is known in different alloys. we showed that the local properties such as hyperfine field, are calculated with acceptable accuracy by using small supercells. Meanwhile, we studied the structural and magnetic properties of different alloys and showed that the Fe alloy has two defferent magnetic phase.

  11. Chemical Insight into the Adsorption of Chromium(III) on Iron Oxide/Mesoporous Silica Nanocomposites.

    Science.gov (United States)

    Egodawatte, Shani; Datt, Ashish; Burns, Eric A; Larsen, Sarah C

    2015-07-14

    Magnetic iron oxide/mesoporous silica nanocomposites consisting of iron oxide nanoparticles embedded within mesoporous silica (MCM-41) and modified with aminopropyl functional groups were prepared for application to Cr(III) adsorption followed by magnetic recovery of the nanocomposite materials from aqueous solution. The composite materials were extensively characterized using physicochemical techniques, such as powder X-ray diffraction, thermogravimetric and elemental analysis, nitrogen adsorption, and zeta potential measurements. For aqueous Cr(III) at pH 5.4, the iron oxide/mesoporous silica nanocomposite exhibited a superior equilibrium adsorption capacity of 0.71 mmol/g, relative to 0.17 mmol/g for unmodified mesoporous silica. The aminopropyl-functionalized iron oxide/mesoporous silica nanocomposites displayed an equilibrium adsorption capacity of 2.08 mmol/g, the highest adsorption capacity for Cr(III) of all the materials evaluated in this study. Energy-dispersive spectroscopy (EDS) with transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS) experiments provided insight into the chemical nature of the adsorbed chromium species. PMID:26134074

  12. Dehydrogenation of propane in the presence of CO{sub 2} over polyacid chromium oxide catalysts modified by Mo, W and Mn

    Energy Technology Data Exchange (ETDEWEB)

    Lapidus, A.L.; Agafonov, Yu.A.; Gaidai, N.A.; Nekrasov, N.V.; Davydov, P.E. [Russian Academy of Sciences, Moscow (Russian Federation). N.D. Zelinsky Institute of Organic Chemistry

    2013-11-01

    Effective chromium oxide catalysts without additions and with addition of Mo, W and Mn were prepared and tested in long-duration experiments for propane dehydrogenation in the presence of CO{sub 2}. The optimal concentrations of metals were found. It was shown that the best combination of acid-base and redox properties necessary for a decrease of aggregation of chromium-oxide particles was observed over the following catalyst: (3.0 wt.%Cr-1.5 wt.% Mn)/SiO{sub 2}. This catalyst worked stably in durable tests (500 h). Mechanism of propane oxidative dehydrogenation was studied using unstationary response method. It was shown that the process mechanism was similar over all studied catalysts but the catalysts were differed by the adsorption capacity of the reaction components: CO{sub 2} was tied more firmly than C{sub 3}H{sub 6} over Cr and Cr-Mn, C{sub 3}H{sub 6} was tied more strongly than CO{sub 2} over Cr-W. The reverse water-gas shift reaction proceeded in more extent over chromium-oxide catalysts without additions. (orig.)

  13. Internal Friction In The PFN Ceramics With Chromium Dopand

    OpenAIRE

    Zachariasz R.; Bochenek D.; Bruś B.

    2015-01-01

    An aim of this work was to determine an influence of an admixture, the chromium (for x from 0.01 to 0.06), on the mechanical properties of the PFN ceramics. The ceramics with chemical composition Pb(Fe0.5−xCrxNb0.5)O3 was synthesized in two steps from simple oxides PbO, Fe2O3, Nb2O5, Cr2O3. The first stage was based on obtaining the FeNbO4 from the Fe2O3 and Nb2O5 simple oxides. At this stage an admixture in a form the Cr2O3 chromium oxide was added to the solution. In the second stage the Pb...

  14. Hexavalent chromium effects on carbon assimilation in Selenastrum capricornutum

    International Nuclear Information System (INIS)

    One of the difficulties in assessing toxic substances such as metals and complex organic compounds is the duration of the necessary tests. It would be beneficial to have available standardized tests of short duration that would allow a reduction in necessary manpower and overall cost as well as provide a method to evaluate chemicals that are readily degraded (i.e., within a few hours). One method available is the short-term photosynthesis response of algae to a given toxicant. Photosynthesis is not only a critical physiological response but is also one for which standard, accurate methods are available. The 14C method has been used to study the effects of chromium on algae. More recently, it was proposed that the 14C method be used to measure short-term photosynthetic response as a standard algal bioassay. The present study was designed to further evaluate, via photosynthetic response, the potential effects of hexavalent chromium on Selenastrum capricornutum

  15. Microwave-assisted Fenton-like decolorization of methyl orange solution using chromium compounds

    Institute of Scientific and Technical Information of China (English)

    LIU Zuo-hua; TAO Chang-yuan; DU Jun; SUN Da-gui; LI Bai-zhan

    2008-01-01

    Azo dyes discharged in the environment are persistent organic pollutants (POPs), which are very difficult to remove. We developed a microwave-assisted Fenton-like process to degrade methyl orange (MO), an azo dye, with hydrogen peroxide (H2O2) catalyzed by chromium compounds coexisting with MO in the solution. Comparison between the Cr(III)-H2O2 and Cr(VI)-H2O2 systems shows that Cr(VI) has a stronger and more stable catalytical activity than Cr(III), and Cr(III) is more susceptible to a change in the acidity or alkalinity of the reaction system. With a Cr(VI) concentration of 10 mmol L-1 or a Cr(III) concentration of 12 mmol L-1 in the solution under the microwave irradiation of a power larger than 300 W for 3 min, 10 mmol L-1 H2O2 can degrade more than 95% of 1 000 mg L-1 methyl orange; when the microwave power is increased to 700 W, the same amount of H2O2 can degrade all methyl orange in the solution with the same amount of Cr(VI) catalyst. Ultraviolet-visible spectrography indicates the cleavage of the azo bond in methyl orange after treatment, suggesting the potential of this Fenton-like process to degrade azo dye POPs. Reusing waste chromium compounds coexisting with dyestuff in wastewater to catalyze the degradation of azo dyes could be a cost-effective technique for azo dyes and chromate manufacturers and/or users to treat their wastewater and prevent POPs from endangering the environment. This is of particular importance to controlling the water quality of the Three Gorges Reservoir.

  16. CHROMIUM (VI ADSORPTION ONTO ACTIVATED KRAFT LIGNIN PRODUCED FROM ALFA GRASS (STIPA TENACISSIMA

    Directory of Open Access Journals (Sweden)

    Nassima Tazrouti

    2009-05-01

    Full Text Available Activated lignin having a surface area of 1023 m2 g-1 has been prepared from sulfate lignin that was treated by 30% H2O2 and carbonized at 300 °C in order to test the chromium (VI adsorption from aqueous solution. The influence of contact time, pH, initial concentrations of adsorbent and adsorbate, and temperature on the adsorption capacity were investi-gated. The maximum removal of Cr(VI was found to be 92.36 % at pH=2 and a contact time of 80 min. Optimal concentration of lignin and Cr(VI were found to be 3.8 g L-1 and 180 mg L-1, respectively. The adsorption kinetics data fitted well with a pseudo-second-order equation, and the rate of removal of chromium was found to speed up with increasing temperature. Activation energy for the adsorption process was found to be 18.19 kJ mol-1. The Langmuir and Freundlich adsorption isotherm models were applied to describe the isotherm and isotherm constants for the adsorption of Cr (VI on lignin. These constants and correlation coefficients of the isotherm models were calculated and compared. Results indicated that Cr (VI uptake could be described by the Langmuir adsorption model. The maximum adsorption capacity (qm of Cr (VI on lignin was 75.75 mg g-1 at 40°C. The dimensionless equilibrium parameter (RL signified a favorable adsorption of Cr (VI on lignin and was found to be between 0.0601 and 0.818 (0reaction was spontaneous and endothermic in nature. This study indicates that lignin has the potential to become an effective and economical adsorbent for removal Cr (VI from waste water.

  17. Hexavalent chromium removal and bioelectricity generation by Ochrobactrum sp. YC211 under different oxygen conditions.

    Science.gov (United States)

    Chen, Chih-Yu; Cheng, Chiu-Yu; Chen, Ching-Kuo; Hsieh, Min-Chi; Lin, Ssu-Ting; Ho, Kuo-Ying; Li, Jo-Wei; Lin, Chia-Pei; Chung, Ying-Chien

    2016-01-01

    Bioremediation is an environmentally friendly method of reducing heavy metal concentration and toxicity. A chromium-reducing bacterial strain, isolated from the vicinity of an electroplate factory, was identified as Ochrobactrum sp. YC211. The efficiency and capacity per time of Ochrobactrum sp. YC211 for hexavalent chromium (Cr(VI)) removal under anaerobic conditions were superior to those under aerobic conditions. An acceptable removal efficiency (96.5 ± 0.6%) corresponding to 30.2 ± 0.8 mg-Cr (g-dry cell weight-h)(-1) was achieved by Ochrobactrum sp. YC211 at 300 mg L(-1) Cr(VI). A temperature of 30°C and pH 7 were the optimal parameters for Cr(VI) removal. By examining reactivated cells, permeabilized cells, and cell-free extract, we determined that Cr(VI) removal by Ochrobactrum sp. YC211 under anaerobic conditions mainly occurred in the soluble fraction of the cell and can be regarded as an enzymatic reaction. The results also indicated that an Ochrobactrum sp. YC211 microbial fuel cell (MFC) with an anaerobic anode was considerably superior to that with an aerobic anode in bioelectricity generation and Cr(VI) removal. The maximum power density and Cr(VI) removal efficiency of the MFC were 445 ± 3.2 mW m(-2) and 97.2 ± 0.3%, respectively. Additionally, the effects of coexisting ions (Cu(2+), Zn(2+), Ni(2+), SO4(2-), and Cl(-)) in the anolyte on the MFC performance and Cr(VI) removal were nonsignificant (P > 0.05). To our knowledge, this is the first report to compare Cr(VI) removal by different cells and MFC types under aerobic and anaerobic conditions. PMID:26889692

  18. Low energy magnetic fluctuations in the TSDW phase of chromium

    Energy Technology Data Exchange (ETDEWEB)

    Azuah, R.T. [Hahn-Meitner Inst., Berlin (Germany); Kulda, J. [Inst. Laue Langevin, Grenoble (France); Pynn, R. [Los Alamos National Lab., NM (United States); Stirling, W.G. [Univ. of Liverpool (United Kingdom). Dept. of Physics

    1997-12-01

    A polarized neutron study of chromium carried out in a field of 6T applied to a single-domain single-Q crystal indicates that the inelastic intensity observed close to the transverse spin density wave (TSDW) satellite positions (1 {+-} {delta}, 0,0) does not behave as expected for spin-wave scattering. In particular, the signal corresponds to magnetization fluctuations of almost equal magnitude both parallel and perpendicular to the ordered moments in the TSDW phase.

  19. Study of Chromium Oxide Activities in EAF Slags

    Science.gov (United States)

    Yan, Baijun; Li, Fan; Wang, Hui; Sichen, Du

    2016-02-01

    The activity coefficients of chromium in Cu-Cr melts were determined by equilibrating liquid copper with solid Cr2O3 in CO-CO2 atmosphere. The temperature dependence of the activity coefficients of chromium in Cu-Cr melts could be expressed as lg γ_{Cr}(s)^{0} = { 3 2 5 9( ± 1 8 6} )/T - 0. 5 9( { ± 0. 1} ). Based on the above results, the activities of bivalent and trivalent chromium oxide in some slags at 1873 K (1600 °C) were measured. The slags were equilibrated with Cu-Cr melts under two oxygen partial pressures ( {p_{O}_{ 2} }} } = 6.9 × 10-4 and 1.8 × 10-6 Pa, respectively). The morphology of the quenched slags and the solubility of chromium oxide in the melts were investigated by EPMA, SEM, and XRD. Under both oxygen partial pressures, the slags were saturated by the solid solution MgAl2- x Cr x O4- δ . At the low oxygen partial pressure (1.8 × 10-6 Pa), the content of Cr in the liquid phase varied from 0.4 to 1.6 mass pct with the total Cr content in the slags increasing from 1.3 to 10.8 mass pct. At the high oxygen partial pressure (6.9 × 10-4 Pa), the content of Cr in the liquid phase decreased to the level of 0.2 to 0.6 mass pct. Both the activities of CrO and Cr2O3 in slag were found to increase approximately linearly with the increase of the total Cr content in slag. While the oxygen partial pressure had minor effect on the activity of Cr2O3 in the slag, it had significant effect on the activity of CrO.

  20. Fretting damage of high carbon chromium bearing steel

    OpenAIRE

    Kuno, Masato

    1988-01-01

    This thesis consists of four sections, the fretting wear properties of high carbon chromium bearing steel; the effect of debris during fretting wear; an introduction of a new fretting wear test apparatus used in this study; and the effects of fretting damage parameters on rolling bearings. The tests were operated under unlubricated conditions. Using a crossed cylinder contact arrangement, the tests were carried out with the normal load of 3N, slip amplitude of 50µm, and frequency of 30Hz ...

  1. Chromium propionate enhances adipogenic differentiation of bovine intramuscular adipocytes

    OpenAIRE

    Rebecca eTokach; Flavio eRibeiro; Ki Yong eChung; Whitney eRounds; Johnson, Bradley J.

    2015-01-01

    In vitro experiments were performed to determine the effects of increasing concentrations of chromium propionate on mRNA and protein abundance of different enzymes and receptors. Intramuscular and subcutaneous preadipocytes and bovine satellite cells were isolated from the longissimus muscle to determine the effect of treatment on glucose transporter type 4 (GLUT4) and peroxisome proliferator-activated receptor γ mRNA and GLUT4 protein abundance. Preadipocyte cultures were treated with diffe...

  2. Chromium Propionate Enhances Adipogenic Differentiation of Bovine Intramuscular Adipocytes

    OpenAIRE

    Tokach, Rebecca J.; Ribeiro, Flavio R. B.; Chung, Ki Yong; Rounds, Whitney; Johnson, Bradley J.

    2015-01-01

    In vitro experiments were performed to determine the effects of increasing concentrations of chromium propionate (CrPro) on mRNA and protein abundance of different enzymes and receptors. Intramuscular (IM) and subcutaneous (SC) preadipocytes and bovine satellite cells were isolated from the longissimus muscle to determine the effect of treatment on glucose transporter type 4 (GLUT4) and peroxisome proliferator-activated receptor γ mRNA and GLUT4 protein abundance. Preadipocyte cultures were t...

  3. Recovery of Chromium from Waste Taning Liquors by Magnesium Oxide

    Directory of Open Access Journals (Sweden)

    Mahmood M. Barbooti

    2010-10-01

    Full Text Available This is a case study of AL-Za’afaraniya tanning factory, 15 km to the south of Baghdad, to spot light on simple chemical treatment of the discharged water to solve the environmental problems associated with its chromium content management. The treatment was extended to the recovery and reuse of chromium. Chromium was precipitated by the addition of magnesium oxide which also aid as a neutralizer for the acidic effluent. The laboratory treatment was carried out to find the optimum conditions. The wastewater samples were taken from the outline area of the tannery. Box-Wilson method was adopted to find useful relationships between the operating variables (temperature, mixing period and magnesium oxide dose and the pH and chromium content of effluent. The experimental data were successfully fitted to second order polynomial mathematical models for the treatment. The most favorable operating conditions for the treatment were: temperature, 30 ºC; mixing period, 50 min and magnesium oxide concentration, 3000 mg/L. On using the optimum conditions a mathematical model simulating the operation for the treatment was obtained as follows:Cr = 6.0848 – 0.001839 X11 – 0.105334 X12 – 0.041038 X13pH = 10.29086 – 0.001223 X11 – 0.140043 X12 – 0.00953 X13Experimentally Cr concentration was decreased to about (0.5 mg/L in wastewater after raising the pH value to (7.35 by adding magnesium oxide.

  4. Soils contaminated with hexavalent chromium : sorption, migration and remediation

    OpenAIRE

    Fonseca, Bruna

    2011-01-01

    The interest in environmental soil science has been growing in the last years due to the continuous degradation of this major natural resource. In this work, a representative sample of a typical loamy sand soil was collected in Porto, Portugal, in a zone of intensive agriculture activity. This soil was used for a series of tests concerning the adsorption, transport and fate of hexavalent chromium. The adsorption equilibrium and sorption kinetics were evaluated through the fitting of several m...

  5. Bioleaching of hexavalent chromium from soils using acidithiobacillus thiooxidans

    OpenAIRE

    Fonseca, Bruna; Rodrigues, Joana; Queiroz, A.M.; Tavares, Teresa

    2010-01-01

    The continuous and growing degradation of the environment, due to several anthropogenic activities, is a main concern of the scientific community. Consequently, the development of low cost techniques to clean air, water and soils are under intense investigation. In this study, the focused problem is the soil contamination by hexavalent chromium, which is known for its several industrial applications - production of stainless steel, textile dyes, wood preservation and leather tanning - its hig...

  6. Biosorption of Hexavalent Chromium from Aqueous Medium with Opuntia Biomass

    OpenAIRE

    José A. Fernández-López; Angosto, José M.; María D. Avilés

    2014-01-01

    The biosorption of hexavalent chromium from aqueous solutions by Opuntia cladodes and ectodermis from cactus fruits was investigated. Both types of biomass are considered low-cost, natural, and ecofriendly biosorbents. Batch experiments were carried out to determine Cr(VI) biosorption capacity and the efficiency of the biosorption process under different pH, initial Cr(VI) concentration, and sorbent dosage. The biosorption of Cr(VI) by Opuntia biomass was highly pH dependent, favoring higher ...

  7. Fabrication and characterisation of uranium, molybdenum, chromium, niobium and aluminium

    International Nuclear Information System (INIS)

    This paper describes fabrication of binary uranium alloys by melting and casting. The following alloys with nominal composition were obtained by melting in the vacuum furnace: uranium with niobium contents from 0.5%- 4.0% and uranium with molybdenum contents from 0.4% - 1.2%. Uranium alloys with chromium content from 0.4% - 1.2% and uranium alloy with 0.12% of aluminium were obtained by vacuum induction furnace (electric arc melting)

  8. Intragranular Chromium Nitride Precipitates in Duplex and Superduplex Stainless Steel

    OpenAIRE

    Iversen, Torunn Hjulstad

    2012-01-01

    Intragranular chromium nitrides is a phenomenon with detrimental effects on material properties in superduplex stainless steels which have not received much attention. Precipitation of nitrides occurs when the ferritic phase becomes supersaturated with nitrogen and there is insufficient time during cooling for diffusion of nitrogen into austenite. Heat treatment was carried out at between 1060◦C and 1160◦C to study the materials susceptibility to nitride precipitation with...

  9. Evidence of weak ferromagnetism in chromium(III) oxide particles

    Energy Technology Data Exchange (ETDEWEB)

    Vazquez-Vazquez, Carlos E-mail: qfmatcvv@usc.es; Banobre-Lopez, Manuel; Lopez-Quintela, M.A.; Hueso, L.E.; Rivas, J

    2004-05-01

    The low temperature (4chromium(III) oxide particles have been studied. A clear evidence of the presence of weak ferromagnetism is observed below 250 K. The magnetisation curves as a function of the applied field show coercive fields due to the canted antiferromagnetism of the particles. Around 55 K a maximum is observed in the zero-field-cooled curves; this maximum can be assumed as a blocking temperature, similarly to ultrafine ferromagnetic particles.

  10. Chronic Maternal Dietary Chromium Restriction Modulates Visceral Adiposity

    OpenAIRE

    Padmavathi, Inagadapa J.N.; Rao, K Rajender; Venu, Lagishetty; Ganeshan, Manisha; Kumar, K. Anand; Rao, Ch. Narasima; Harishankar, Nemani; Ismail, Ayesha; Raghunath, Manchala

    2009-01-01

    OBJECTIVE We demonstrated previously that chronic maternal micronutrient restriction altered the body composition in rat offspring and may predispose offspring to adult-onset diseases. Chromium (Cr) regulates glucose and fat metabolism. The objective of this study is to determine the long-term effects of maternal Cr restriction on adipose tissue development and function in a rat model. RESEARCH DESIGN AND METHODS Female weanling WNIN rats received, ad libitum, a control diet or the same with ...

  11. Chromium and manganese interactions in streptozocin-diabetic rats

    Energy Technology Data Exchange (ETDEWEB)

    Davis, M.L.; Jarrett, C.R.; Adeleye, B.O.; Stoecker, B.J. (Oklahoma State Univ., Stillwater (United States))

    1991-03-15

    Weanling male rats were fed casein-based diets low in chromium and manganese ({minus}Cr-MN) or supplemented with 1 ppm chromium as chromium chloride (+Cr) and/or 55 ppm manganese as manganous carbonate in a factorial design. After 7 weeks on the experimental diets, half of the rats in each group were injected on 2 consecutive days with 55 mg/kg streptozocin (STZ) in citrate buffer pH 4. Four weeks after injection, serum glucose in the diabetic group supplement with both Cr and Mn was not different from non-diabetic animals; however, diabetic animals in {minus}Cr groups or in the +Cr-Mn group had significantly elevated serum glucose. Serum insulin was reduced by STZ. A significant interaction between Mn and diabetes affected serum cortisol concentrations. More new tissue was formed on a polyvinyl sponge inserted under the skin in +Mn animals. In this study, the STZ animals were more sensitive than the control animals to dietary Cr and Mn concentrations.

  12. Magnesium, zinc, and chromium nutriture and physical activity.

    Science.gov (United States)

    Lukaski, H C

    2000-08-01

    Magnesium, zinc, and chromium are mineral elements required in modest amounts to maintain health and optimal physiologic function. For physically active persons, adequate amounts of these micronutrients are needed in the diet to ensure the capacity for increased energy expenditure and work performance. Most physically active individuals consume diets that provide amounts of magnesium and zinc sufficient to meet population standards. Women tend to consume less of these minerals than is recommended, in part because they eat less food than men. Inadequate intakes of magnesium and zinc have been reported for participants in activities requiring restriction of body weight. Dietary chromium is difficult to estimate because of a lack of appropriate reference databases. Acute, intense activity results in short-term increases in both urine and sweat losses of minerals that apparently diminish during recovery in the days after exercise. Supplemental magnesium and zinc apparently improve strength and muscle metabolism. However, evidence is lacking as to whether these observations relate to impaired nutritional status or a pharmacologic effect. Chromium supplementation of young men and women does not promote muscle accretion, fat loss, or gains in strength. Physically active individuals with concerns about meeting guidelines for nutrient intake should be counseled to select and consume foods with high nutrient densities rather than to rely on nutritional supplements. The indiscriminate use of mineral supplements can adversely affect physiologic function and impair health.

  13. Structure and growth of oxide on iron-chromium alloys

    International Nuclear Information System (INIS)

    Several oxides form during the initial stages of oxidation of iron-chromium alloys at 400 to 6000C in CO2-1%CO gas. The nature of the oxidation product depends upon crystallographic orientation and composition of the substrate, and can be explained by considering the maximum solubility of chromium in different oxide phases together with interfacial and strain energy factors. Kinetics of oxidation together with micrographic observations indicate that, as oxidation proceeds spinel oxide M3O4 nucleates at sites on the substrate surface associated with asperities. The spinel nuclei grow laterally and vertically until they coalesce and the scale subsequently thickens according to a parabolic rate law. The duplex structure of scales is interpreted in terms of an outward diffusion of cations together with simultaneous growth of an inner layer in the space created by this outward movement. Scale porosity provides a route for gas-phase transport of oxidant to support the growth of the inner layer. Regularly spaced lamellar voids which may form in the inner layer are believed to be associated with a cyclic vacancy condensation process. Enrichment of the inner layer in chromium is explained by analysis of the possible diffusion path networks in close-packed oxides. Some comments are made concerning possible practical applications of these data. (author)

  14. Study on anaerobic treatment of wastewater containing hexavalent chromium.

    Science.gov (United States)

    Xu, Yan-bin; Xiao, Hua-hua; Sun, Shui-yu

    2005-06-01

    A self-made anaerobic bio-filter bed which was inoculated with special sludge showed high efficiency in removing hexavalent chromium. When pump flow was 47 ml/min and COD(Cr) of wastewater was about 140 mg/L, it took 4 h to decrease the Cr6+ concentrations from about 60 mg/L to under 0.5 mg/L, compared with 14 h without carbon source addition. Cr6+ concentrations ranged from 64.66 mg/L to 75.53 mg/L, the system efficiency was excellent. When Cr6+ concentration reached 95.47 mg/L, the treatment time was prolonged to 7.5 h. Compared with the contrast system, the system with trace metals showed clear superiority in that the Cr6+ removal rate increased by 21.26%. Some analyses also showed that hexavalent chromium could probably be bio-reduced to trivalent chromium, and that as a result, the chrome hydroxide sediment was formed on the surface of microorganisms.

  15. Study on anaerobic treatment of wastewater containing hexavalent chromium*

    Science.gov (United States)

    Xu, Yan-bin; Xiao, Hua-hua; Sun, Shui-yu

    2005-01-01

    A self-made anaerobic bio-filter bed which was inoculated with special sludge showed high efficiency in removing hexavalent chromium. When pump flow was 47 ml/min and CODCr of wastewater was about 140 mg/L, it took 4 h to decrease the Cr6+ concentrations from about 60 mg/L to under 0.5 mg/L, compared with 14 h without carbon source addition. Cr6+ concentrations ranged from 64.66 mg/L to 75.53 mg/L, the system efficiency was excellent. When Cr6+ concentration reached 95.47 mg/L, the treatment time was prolonged to 7.5 h. Compared with the contrast system, the system with trace metals showed clear superiority in that the Cr6+ removal rate increased by 21.26%. Some analyses also showed that hexavalent chromium could probably be bio-reduced to trivalent chromium, and that as a result, the chrome hydroxide sediment was formed on the surface of microorganisms. PMID:15909347

  16. Study on anaerobic treatment of wastewater containing hexavalent chromium

    Institute of Scientific and Technical Information of China (English)

    XU Yan-bin; XIAO Hua-hua; SUN Shui-yu

    2005-01-01

    A self-made anaerobic bio-filter bed which was inoculated with special sludge showed high efficiency in removing hexavalent chromium. When pump flow was 47 ml/min and CODCr ofwastewater was about 140 mg/L, it took 4 h to decrease the Cr6+ concentrations from about 60 mg/L to under 0.5 mg/L, compared with 14 h without carbon source addition. Cr6+ concentrations ranged from 64.66 mg/L to 75.53 mg/L, the system efficiency was excellent. When Cr6+ concentration reached 95.47 mg/L,the treatment time was prolonged to 7.5 h. Compared with the contrast system, the system with trace metals showed clear superiority in that the Cr6+ removal rate increased by 21.26%. Some analyses also showed that hexavalent chromium could probably be bio-reduced to trivalent chromium, and that as a result, the chrome hydroxide sediment was formed on the surface of microorganisms.

  17. Response of soil catalase activity to chromium contamination

    Institute of Scientific and Technical Information of China (English)

    Zofia St(e)pniewska; Agnieszka Woli(n)ska; Joanna Ziomek

    2009-01-01

    The impact of chromium (III) and (VI) forms on soil catalase activity is presented.The Orthic Podzol, Haplic Phaeozem and Mollic Gleysol from different depths were used in the experiment.The soil samples were amended with solution of Cr(III) using CrCl3, and with Cr(VI) using K2Cr2O7 in the concentration range from 0 to 20 mg/kg, whereas the samples without the addition of chromium served as control.Catalase activity was assayed by one of the commonly used spectrophotometric methods.As it is demonstrated in the experiment, both Cr(III) and Cr(VI) forms have ability to reduce soil catalase activity.A chromium dose of 20 mg/kg caused the inhibition of catalase activity and the corresponding contamination levels ranged from 75% to 92% for Cr(III) and 68% to 76% for Cr(VI), with relation to the control.Catalase activity reached maximum in the soil material from surface layers (0-25 cm), typically characterized by the highest content of organic matter creating favorable conditions for microorganisms.

  18. Fabrication of chitosan-magnetite nanocomposite strip for chromium removal

    Science.gov (United States)

    Sureshkumar, Vaishnavi; Kiruba Daniel, S. C. G.; Ruckmani, K.; Sivakumar, M.

    2016-02-01

    Environmental pollution caused by heavy metals is a serious threat. In the present work, removal of chromium was carried out using chitosan-magnetite nanocomposite strip. Magnetite nanoparticles (Fe3O4) were synthesized using chemical co-precipitation method at 80 °C. The nanoparticles were characterized using UV-visible spectroscopy, fourier transform infrared spectroscopy, X-ray diffraction spectrometer, atomic force microscope, dynamic light scattering and vibrating sample magnetometer, which confirm the size, shape, crystalline nature and magnetic behaviour of nanoparticles. Atomic force microscope revealed that the particle size was 15-30 nm and spherical in shape. The magnetite nanoparticles were mixed with chitosan solution to form hybrid nanocomposite. Chitosan strip was casted with and without nanoparticle. The affinity of hybrid nanocomposite for chromium was studied using K2Cr2O7 (potassium dichromate) solution as the heavy metal solution containing Cr(VI) ions. Adsorption tests were carried out using chitosan strip and hybrid nanocomposite strip at different time intervals. Amount of chromium adsorbed by chitosan strip and chitosan-magnetite nanocomposite strip from aqueous solution was evaluated using UV-visible spectroscopy. The results confirm that the heavy metal removal efficiency of chitosan-magnetite nanocomposite strip is 92.33 %, which is higher when compared to chitosan strip, which is 29.39 %.

  19. Selective Chromium(VI) Ligands Identified Using Combinatorial Peptoid Libraries

    Science.gov (United States)

    Knight, Abigail S.; Zhou, Effie Y.; Pelton, Jeffrey G.; Francis, Matthew B.

    2013-01-01

    Hexavalent chromium (Cr(VI)) is a world-wide water contaminant that is currently without cost-effective and efficient remediation strategies. This is in part due to a lack of ligands that can bind it amid an excess of innocuous ions in aqueous solution. We present herein the design and application of a peptoid-based library of ligand candidates for toxic metal ions. A selective screening process was used to identify members of the library that can bind to Cr(VI) species at neutral pH and in the presence of a large excess of spectator ions. Eleven sequences were identified, and their affinities were compared using titrations monitored with UV-Vis spectroscopy. To identify the interactions involved in coordination and specificity, we evaluated the effects of sequence substitutions and backbone variation in the highest affinity structure. Additional characterization of the complex formed between this sequence and Cr(VI) was performed using NMR spectroscopy. To evaluate the ability of the developed sequences to remediate contaminated solutions, the structures were synthesized on a solid-phase resin and incubated with environmental water samples that contained simulated levels of chromium contamination. The synthetic structures demonstrated the ability to reduce the amount of toxic chromium to levels within the range of the EPA contamination guidelines. In addition to providing some of the first selective ligands for Cr(VI), these studies highlight the promise of peptoid sequences as easily-prepared components of environmental remediation materials. PMID:24195610

  20. Eolian transport of geogenic hexavalent chromium to ground water

    Science.gov (United States)

    Wood, W.W.; Clark, D.; Imes, J.L.; Councell, T.B.

    2010-01-01

    A conceptual model of eolian transport is proposed to address the widely distributed, high concentrations of hexavalent chromium (Cr+6) observed in ground water in the Emirate of Abu Dhabi, United Arab Emirates. Concentrations (30 to more than 1000 μg/L Cr+6) extend over thousands of square kilometers of ground water systems. It is hypothesized that the Cr is derived from weathering of chromium-rich pyroxenes and olivines present in ophiolite sequence of the adjacent Oman (Hajar) Mountains. Cr+3 in the minerals is oxidized to Cr+6 by reduction of manganese and is subsequently sorbed on iron and manganese oxide coatings of particles. When the surfaces of these particles are abraded in this arid environment, they release fine, micrometer-sized, coated particles that are easily transported over large distances by wind and subsequently deposited on the surface. During ground water recharge events, the readily soluble Cr+6 is mobilized by rain water and transported by advective flow into the underlying aquifer. Chromium analyses of ground water, rain, dust, and surface (soil) deposits are consistent with this model, as are electron probe analyses of clasts derived from the eroding Oman ophiolite sequence. Ground water recharge flux is proposed to exercise some control over Cr+6 concentration in the aquifer.

  1. Bioremediation of hexavalent chromium by a cyanobacterial mat

    Science.gov (United States)

    Shukla, Dhara; Vankar, Padma S.; Srivastava, Sarvesh Kumar

    2012-12-01

    The study comprises the use of cyanobacterial mat (collected from tannery effluent site) to remove hexavalent chromium. This mat was consortium of cyanobacteria/blue-green algae such as Chlorella sp., Phormidium sp. and Oscillatoria sp. The adsorption experiments were carried out in batches using chromium concentrations 2-10, 15-30 and 300 ppm at pH 5.5-6.2. The adsorption started within 15 min; however, 96 % reduction in metal concentration was observed within 210 min. The adsorption phenomenon was confirmed by Fourier transform-infrared spectroscopy and energy dispersive X-ray analysis. This biosorption fitted Freundlich adsorption isotherm very well. It was observed that the best adsorption was at 4 ppm, and at 25 ppm in the chosen concentration ranges. Scanning electron micrograph showed the physiology of mat, indicating sites for metal uptake. The main focus was collection of the cyanobacterial mat from local environments and its chromium removal potential at pH 5.5-6.2.

  2. Fabrication of Carbon Nanotube - Chromium Carbide Composite Through Laser Sintering

    Science.gov (United States)

    Liu, Ze; Gao, Yibo; Liang, Fei; Wu, Benxin; Gou, Jihua; Detrois, Martin; Tin, Sammy; Yin, Ming; Nash, Philip; Tang, Xiaoduan; Wang, Xinwei

    2016-03-01

    Ceramics often have high hardness and strength, and good wear and corrosion resistance, and hence have many important applications, which, however, are often limited by their poor fracture toughness. Carbon nanotubes (CNTs) may enhance ceramic fracture toughness, but hot pressing (which is one typical approach of fabricating CNT-ceramic composites) is difficult to apply for applications that require localized heat input, such as fabricating composites as surface coatings. Laser beam may realize localized material sintering with little thermal effect on the surrounding regions. However, for the typical ceramics for hard coating applications (as listed in Ref.[1]), previous work on laser sintering of CNT-ceramic composites with mechanical property characterizations has been very limited. In this paper, research work has been reported on the fabrication and characterization of CNT-ceramic composites through laser sintering of mixtures of CNTs and chromium carbide powders. Under the studied conditions, it has been found that laser-sintered composites have a much higher hardness than that for plasma-sprayed composites reported in the literature. It has also been found that the composites obtained by laser sintering of CNTs and chromium carbide powder mixtures have a fracture toughness that is ~23 % higher than the material obtained by laser sintering of chromium carbide powders without CNTs.

  3. The chromium site in doped glassy lithium tetraborate

    Energy Technology Data Exchange (ETDEWEB)

    Kelly, T.D. [Department of Engineering Physics, Air Force Institute of Technology, 2950 Hobson Way, Wright Patterson Air Force Base, OH 45433 (United States); Echeverria, E.; Beniwal, Sumit [Department of Physics and Astronomy, 855 North 16th Street, Theodore Jorgensen Hall, University of Nebraska-Lincoln, Lincoln, NE 68588-0299 (United States); Adamiv, V.T.; Burak, Ya. V.; Enders, Axel [Institute of Physical Optics, 23 Dragomanov Street, Lviv 79005 (Ukraine); Petrosky, J.C.; McClory, J.W. [Department of Engineering Physics, Air Force Institute of Technology, 2950 Hobson Way, Wright Patterson Air Force Base, OH 45433 (United States); Dowben, P.A., E-mail: pdowben1@unl.edu [Department of Physics and Astronomy, 855 North 16th Street, Theodore Jorgensen Hall, University of Nebraska-Lincoln, Lincoln, NE 68588-0299 (United States)

    2014-10-15

    Using extended X-ray absorption fine structure (EXAFS) spectroscopy, we find that Cr substitutes primarily in the Li{sup +} site as a dopant in lithium tetraborate Li{sub 2}B{sub 4}O{sub 7} glasses, in this case 98.4Li{sub 2}B{sub 4}O{sub 7}–1.6Cr{sub 2}O{sub 3} or nominally Li{sub 1.98}Cr{sub 0.025}B{sub 4}O{sub 7}. This strong preference for a single site is nonetheless accompanied by site distortions and some site disorder, helping explain the optical properties of chromium doped Li{sub 2}B{sub 4}O{sub 7} glasses. The resulting O coordination shell has a contraction of the Cr–O bond lengths as compared to the Li–O bond lengths. There is also an increase in the O coordination number. - Graphical abstract: Lithium tetraborate: labeled are the B1 and B2 sites, where the latter correspond to BO{sub 3} and BO{sub 4} structures respectively. - Highlights: • Adoption of the Li + site for chromium dopants in lithium tetraborate identified. • Increased oxygen coordination for glass over the crystalline lithium tetraborate. • Distortions about the doping chromium characterized. • Local bond order is preserved in spite of the glassy nature.

  4. Preparation of Silica Modified with 2-Mercaptoimidazole and its SorptionProperties of Chromium(III

    Directory of Open Access Journals (Sweden)

    Harry Budiman

    2009-01-01

    Full Text Available Modified silica gel was prepared to remove the heavy metal of chromium(III from water sample. Silica gel was used as supporting material and the 2-mercaptoimidazole was immobilized onto surface silica so that the silica would have selective properties to adsorb the heavy metal chromium(III through the formation of coordination compound between the 2-mercaptoimidazole and chromium(III. The characterization of modified silica gel was carried out by analyzing the Fourier Transform Infrared Spectrum of this material in order to ensure the immobilization of 2-mercaptoimidazole onto the surface. The effect of pH solution, initial concentration of chromium(III, and interaction time were investigated in batch mode to find the adsorption properties of chromium(III onto modified silica. The condition optimum of these parameters was applied to determine the removal percentage of chromium(III in water sample using the modified silica gel

  5. Biological monitoring of occupational exposure to different chromium compounds at various valency states

    Energy Technology Data Exchange (ETDEWEB)

    Mutti, A.; Pedroni, C.; Arfini, G.; Franchini, I.; Minoia, C.; Micoli, G.; Baldi, C.

    1984-01-01

    Chromium concentrations in the air were measured in seven different workroom environments, where exposure to water soluble hexavalent or trivalent compounds was expected. Urinary excretion of chromium was measured before and after the same arbitrarily chosen working day. End-of-shift urinary chromium and its increase above pre-exposure levels were closely related to the concentration of water soluble chromium (VI) in the air. The values corresponding to 50 micrograms m-3 in the air, which is the current threshold limit value in most countries, were 29.8 and 12.2 micrograms g-1 of creatinine, respectively. Urinary chromium in workers exposed to water insoluble chromates or to water soluble chromic (III) sulphate was definitely higher than that observed in subjects not occupationally exposed to chromium compounds, but it cannot be recommended as short-term exposure test for evaluation of the job-related hazard.

  6. Determination of Chromium(III) Picolinate Using High Performance Liquid Chromatography-Ultraviolet Spectrophotometry

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sung Il; Woo, Dong Jin; Kang, Dae Kyung [EASY BIO System, Inc, Chonan (Korea, Republic of); Lee, Myung Hee [Pollin, Inc, Seoul (Korea, Republic of); Woo, Gun Jo [Korea Food and Drug Administration, Seoul (Korea, Republic of); Cha, Ki Won [Inha University, Incheon (Korea, Republic of)

    2003-10-15

    Cr-(pic){sub 3} has been widely used as food additives, drugs, and feed additives. Accordingly, its determination method should be established. In the present paper, we have studied the determination method of chromium(III) picolinate accurately using ESI-MS on-lined with HPLC. Chromium(III) picolinate in feed products was determined successfully. Chromium(III) is very well known as an essential mineral. It is suggested as a cofactor in the maintenance of both normal lipid and carbohydrate metabolism by assisting the action of insulin on a cell membrane. According to the National Research Council, the daily recommended intake of chromium(III) is 50-200 μg. Several organic chromium(III) complexes have been reported to have significantly higher absorption and tissue incorporation activity than inorganic salts such as chromium(III) chloride.

  7. Chemical composition and structural transformations of amorphous chromium coatings electrodeposited from Cr(III) electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Safonova, Olga V. [Swiss-Norwegian Beamlines at European Synchrotron Radiation Facility, 38043 Grenoble Cedex (France); Vykhodtseva, Ludmila N. [Department of Electrochemistry, Faculty of Chemistry, Moscow State University, 119991 Moscow (Russian Federation); Polyakov, Nikolai A. [A.N. Frumkin Institute of Physical Chemistry and Electrochemistry, Russian Academy of Sciences, 119991 Moscow (Russian Federation); Swarbrick, Janine C. [European Synchrotron Radiation Facility, 38043 Grenoble Cedex (France); Sikora, Marcin [European Synchrotron Radiation Facility, 38043 Grenoble Cedex (France); Department of Solid State Physics, Faculty of Physics and Applied Computer Science, AGH University of Science and Technology, Av. Mickiewicza 30, 30-059 Krakow (Poland); Glatzel, Pieter [European Synchrotron Radiation Facility, 38043 Grenoble Cedex (France); Safonov, Viktor A., E-mail: safon@elch.chem.msu.r [Department of Electrochemistry, Faculty of Chemistry, Moscow State University, 119991 Moscow (Russian Federation)

    2010-12-15

    Amorphous chromium coatings were electrodeposited from Cr(III)-based solutions containing organic (HCOONa) or phosphorus-containing (NaH{sub 2}PO{sub 2}) additives. Their structure was studied by a combination of X-ray diffraction (XRD), valence-to-core X-ray emission spectroscopy (XES) and X-ray absorption spectroscopy (XAS) at the Cr K-edge. Metalloid atoms (C or P) incorporated in electroplates structure are chemically bonded to chromium (i.e. are located in the first coordination shell). Upon annealing at elevated temperatures in vacuum, these amorphous coatings crystallize into a mixture of phases containing metallic chromium and chromium carbides or chromium phosphides. Quantitative analysis of valence-to-core XES data demonstrates that the average local structure of chromium in the amorphous coatings does not change significantly during crystallization.

  8. Chromium related degradation of solid oxide fuel cells; Chrom-bezogene Degradation von Festoxid-Brennstoffzellen

    Energy Technology Data Exchange (ETDEWEB)

    Neumann, Anita

    2011-05-04

    Solid Oxide Fuel Cells (SOFCs) offer a high potential for application as an auxiliary power unit (APU) for heavy goods vehicles as well as combined heat and power (CHP) systems. SOFCs are especially attractive due to their high efficiencies and the use of different fuel types. However, optimization in terms of long term stability and costs are still necessary. This work characterized the degradation of SOFCs with lanthanum strontium manganite (LSM) cathodes under chromium influence. Galvanostatic cell tests were carried out at 800 C with operation times from 250 - 3000 h and variation of the chromium source and current density. The current densities of j = 0 (A)/(cm{sup 2}), j = 0,3 (A)/(cm{sup 2}) and j = 0,5 (A)/(cm{sup 2}) were applied. The high temperature ferritic alloy Crofer22APU was used as a chromium source. Variation of the chromium source was realized by coating the Crofer22APU insert with the chromium retention layer Mn{sub 3}O{sub 4} and the cathode contact layer LCC10. Cell degradation was analyzed with regard to cell voltage, current density and area specific resistance (ASR). Microstructural alterations of the cathode as well as chromium content and distribution across the cell were investigated after completion of the cell tests. For cells with a chromium source present and operation with a nonzero current density, the course of cell degradation was divided into three phases: a run-in, weak linear degradation and strong linear degradation. A decrease of the chromium release rate by means of different coatings stretched the course of degradation along the timescale. Strong degradation, which is characterized by a significant increase in ASR as well as a decrease of current density at the operating point, was only observed when a chromium source in the setup was comb ined with operation of the cell with a non-zero current density. Operation of the cell with a chromium source but no current density caused a degradation of current density at the

  9. Tuberculin reaction and BCG scar

    DEFF Research Database (Denmark)

    Timmermann, Clara Amalie Gade; Biering-Sørensen, Sofie; Aaby, Peter;

    2015-01-01

    rate ratio (MRR) comparing children with a BCG scar with those without was 0.42 (95% CI = 0.19; 0.93). There was a similar tendency for TST positivity: MRR = 0.47 (95% CI = 0.14; 1.54). For LBW children who had both a positive TST reaction and a scar, the MRR was 0.22 (95% CI = 0.05; 0.87). For NBW...

  10. Caracterización Fitoquímica y Efecto Hipoglucemiante de Tecoma stans y su Relación con la Presencia del Cromo como Factor de Tolerancia a la Glucosa Phytochemical Characterization and Hypoglycemic Effect of the Tecoma stans and its Relationship to the Presence of Chromium as a Factor for Glucose Tolerance

    Directory of Open Access Journals (Sweden)

    Ma. de J Ibarra

    2009-01-01

    Full Text Available Se realizó la caracterización fitoquímica y la determinación del cromo en hojas de Tecoma stans, observando su efecto hipoglucemiante en animales con diabetes mellitus inducida en forma experimental. Como hiperglucemiante se utilizó estreptozotocina en ratas machos Sprague-Dawley a una dosis de 45 mg/kg de peso. Los tratamientos experimentales, todos por vía oral, fueron los siguientes para grupos diabéticos y grupos no diabéticos: agua, infusión de la planta, picolinato de cromo, e infusión combinada con picolinato de cromo. Se encontró cromo en T. stans (54 µg/100g, la hiperglucemia disminuyó hasta 33.5 % con T. stans, 10.1% con picolinato de cromo y 32.3% con la combinación de T. stans y picolinato de cromo, en 45 días. Con este estudio se confirma el efecto hipoglucemiante de T. stans.Phytochemical characterization of Tecoma stans leaves, determination of chromium and their hypoglucemiant action in experimental animals with induced diabetes was done. The hyperglucemiant streptozotocin was employed in Sprague Dawley male rats at a dose of 45 mg/kg. The experimental treatments, all orally delivered, were the following for both diabetic and non diabetic groups: water, infusion of the plant, chromium picolinate and infusion combined with chromium picolinato. Chromium was found in T. stans (54 µg/100g, glucose levels decreased up to 33, 5 % with T. stans, 10, 1% with chromium picolinate and 32, 3% with the combination of T. stans and chromium picolinate, in 45 days. The hypoglucemiant effect of T. stans was confirmed with this study.

  11. USE OF TWO DIGESTION METHODS IN THE EVALUATION OF CHROMIUM CONTENT IN CATTLE'S MEAT SUPPLEMENTED WITH CHROMIUM CHELATES

    Directory of Open Access Journals (Sweden)

    R. L. T. de Andrade

    2015-06-01

    Full Text Available The present study aimed to analyze the chromium content in beef using two digestion methods. There were used samples from 24 18-month-old male cattle, and twelve of them were supplemented and twelve were not supplemented with chromium chelate. These samples were evaluated by atomic absorption spectroscopy, previously submitted to digestion method using nitric acid (65% with hydrogen peroxide (35% and to digestion method, using solution of nitric perchloric acid in the proportion 3:1. Immediately after the slaughter, the carcasses were sent to sanitary maturation. After 24 hours, samples between 12th and 13th rib in the muscle Longissimus Thoracis were taken. For evaluation, it was used completely randomized design (Die and analysis of variance (ANOVA at 5% of significance level. The results didn't evidenced any significant difference (p>0,05 between the (cromo content, regardless the supplementation. The same happened with the digestion methods used.

  12. Characteristics of Aerosols Containing Chromium and Nickel From Some Thermal Spraying Operations

    OpenAIRE

    Bohgard, Mats; Welinder, Hans; Akselsson, Roland

    1983-01-01

    Characterization of aerosols, emitted from five methods of thermal spraying with materials containing chromium and nickel were carried out. The characterization procedure includes the determinations of the metal content, the particle size distribution, the oxidation state of chromium and a measure of the solubility of chromium. Three different kinds of samplers and the analytical methods PIXE (Particle Induced X-ray Emission analysis), ESCA (Electron Spectroscopy for Chemical Analysis), AAS (...

  13. Optimization and Modeling of Hexavalent Chromium Removal from Aqueous Solution Via Adsorption on Multiwalled Carbon Nanotubes

    OpenAIRE

    Mina Gholipour; Hassan Hashemipour Rafsanjani; Ataollah Soltani Goharrizi

    2011-01-01

    Hexavalent chromium and its derivatives are potential pollutant due to their mortal affects. Therefore, It is essential to remove these components from wastewaters before disposal. Adsorption can be effective and versatile method for removing of hexavalent chromium. In this article, removal of hexavalent chromium via adsorption on multiwalled carbon nanotubes was investigated as a function of adsorbent dosage, initial solution pH, initial Cr(VI) concentrations, contact time and temperature. T...

  14. Enhancing phytoremediation of chromium-stressed soils through plant-growth-promoting bacteria

    OpenAIRE

    Munees Ahemad

    2015-01-01

    Chromium, specifically hexavalent chromium is one of the most toxic pollutants that are released into soils by various anthropogenic activities. It has numerous adverse effects not only on plant system but also on beneficial soil microorganisms which are the indicators of soil fertility and health. Recent emergence of phytoremediation as an environmental friendly and economical approach to decontaminate the chromium stressed soils has received wider attention. But major drawback of this proce...

  15. Removal of hexavalent chromium of contaminated soil by coupling electrokinetic remediation and permeable reactive biobarriers

    OpenAIRE

    Fonseca, Bruna; Pazos, M.; Tavares, M. T.; Sanromán, M. A.

    2012-01-01

    PURPOSE: In this study, a novel and ecological alternative have been developed to treat soils contaminated with hexavalent chromium coupling two well-known systems: electrokinetic remediation and permeable reactive biobarriers. The electric field promotes the electromigration of the hexavalent chromium oxyanions towards the anode. The biobarriers were placed before the anode electrode, in order to promote the reduction and retention of the chromium migrating in its direction. Thus, this t...

  16. Determination of Chromium Content in Human Skin by Means of Neutron Activation Analysis

    International Nuclear Information System (INIS)

    Chromium eczema is a well-known phenomenon in dermatological practice. Different explanations may be given for it. According to one of these the specific texture of the skin of patients is assumed to allow more chromium to pass through the upper layers. As a result, the chromium accumulates faster in the dermis of patients so that a critical value is reached sooner. Another explanation might be that die sensitivity threshold for chromium in patients is lower than in normal persons and can more easily be exceeded. To distinguish between these possibilities and to obtain more information, an investigation was started in which the chromium content in the skin was compared for eczema patients and normal people. The sample weight (10 mg) and the chromium content (0.2 - 0.4 ppm) involved require a sensitive technique. Neutron activation analysis is well suited to this purpose. Under our operation conditions (irradiation time 10 days, neutron flux 1014n/cm2s) it is possible to determine quantities as low as 5 x 10-11 g of chromium. Preliminary experiments show relatively large variations in chromium content of comparable samples, even in skin samples taken from the back of a single person. It is further suggested by the results of these experiments that the chromium content in the skin of eczema patients is lower than in that of normal patients. The results of the analysis may be seriously affected by chromium contamination during sample preparation. Therefore chromium-free instruments must be used. To avoid chromium migration in the skin due to degeneration processes, samples must be taken from persons alive or shortly after their death. (author)

  17. SYNTHESIS AND ANTIBACTERIAL ACTIVITY OF NEW SULFONAMIDE ISOXAZOLO[5,4-b]PYRIDINE DERIVATIVES.

    Science.gov (United States)

    Poręba, Krystyna; Pawlik, Krzysztof; Rembacz, Krzysztof P; Kurowska, Ewa; Matuszyk, Janusz; Długosz, Anna

    2015-01-01

    A series of novel sulfonamide isoxazolo[5,4-b]pyridines were synthesized. The substrates for their synthesis were 3-aminoisoxazolo[5,4-b]pyridine and selected aryl sulfonic chlorides, chlorosulfonic acid and selected amines. Reactions were carried out using the classical and microwave methods. Selected compounds were tested towards antibacterial and antiproliferative activity. The structure of the obtained new derivatives was determined by elemental analysis and acquired IR and 1H NMR spectra. Among the tested compounds: N- isoxazolo[5,4-b]pyridine-3-yl-benzenesulfonamide (2) and N-isoxazolo[5,4-b]pyridine-3-yl-4-methylbenzene-sulfonamide (5) showed antimicrobial activity towards Pseudomonas aeruginosa (ATCC 27853) and Escherichia coli (ATCC 25922) at doses: 125, 250 and 500 µg. Both compounds showed a 50% inhibition of proliferation of breast carcinoma cell line MCF7 at concentrations of 152.56 µg/mL and 160 161.08 µg/mL, respectively. PMID:26647630

  18. Chromium Isotopes in Marine Carbonates - an Indicator for Climatic Change?

    Science.gov (United States)

    Frei, R.; Gaucher, C.

    2010-12-01

    Chromium (Cr) stable isotopes experience an increased interest as a tracer of Cr (VI) reduction in groundwater and thus showed their potential as a monitor of remediation of anthropogenic and natural contamination in water (Berna et al., 2009; Izbicki et al., 2008). Chromium stable isotopes in Fe-rich chemical sediments (BIFs and Fe-cherts) have recently also been used as a tracer for Earth's atmospheric oxygenation through time (Frei et al., 2009). We have applied the Cr isotope system to organic-rich carbonates from a late Ediacaran succession in Uruguay (Polanco Formation), from which we have previously analyzed BIFs with extremely fractionated (δ53Cr up to 5.0 ‰) Cr isotope signatures that are part of an underlying deep water clastic sediment (shale-dominated) sequence (Yerbal Formation) deposited in a glacio-marine environment (Gaucher et al.,2004). δ53Cr values of organic rich carbonates correlate with positive and negative carbon isotope excursions (δ13C PDB between -3 and +3 ‰) and with systematic changes in strontium isotope compositions, commonly interpreted as to reflect fluctuations in organic (photosynthetic algae) production related to fluctuations in atmospheric oxygen and weathering intensities, respectively. Slightly positively fractioned δ53Cr values (up to +0.25‰), paralleling positive (δ13C PDB and 87Sr/86Sr ratio excursions would thereby trace elevated atmospheric oxygen levels/pulses possibly related to glacier retreat/melting stages that caused bioproductivity to increase. While the causal link between these multiple isotopic tracers and the mechanisms of Cr stripping into carbonates has to be further investigated in detail, the first indications from this study point to a potentially promising use of stable Cr isotopes in organic-rich carbonates to monitor fluctuations of atmospheric oxygen, particularly over the Neoproterozoic and Phanerozoic ice age periods. E.C. Berna et al. (2010) Cr stable isotopes as indicators of Cr

  19. Progress in the chemistry of chromium(V) doping agents used in polarized target materials

    Energy Technology Data Exchange (ETDEWEB)

    Krumpolc, M. (Illinois Univ., Chicago, IL (USA)); Hill, D. (Argonne National Lab., IL (USA)); Struhrmann, H.B. (Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany, F.R.). Hamburger Synchrotronstrahlungslabor)

    1990-01-01

    We wish to report progress in two areas of the chromium (V)-based doping agents: Two commonly used chromium (V) complexes, I and II, have been synthesized in perdeuterated form (i.e., all hydrogens replaced by deuterium). They are sodium bis(2-ethyl-2-deuteroxy-butyrato)oxochromate(V)monodeuterate, IV, (acronym EDBA-Cr(V)), and sodium bis(2-deuteroxy-2-methylpropionato)oxochromate(V), III, (acronym DMPA-Cr(V)). A synthetic route leading to the preparation of stable, chromium(III)-free solutions of chromium(V) in diols (1,2-ethanediol/ethylene glycol/and 1,2-propanediol/propylene glycol/) has been outlined.

  20. Hexavalent chromium and its effect on health: possible protective role of garlic (Allium sativum Linn).

    Science.gov (United States)

    Das, Kusal K; Dhundasi, Salim A; Das, Swastika N

    2011-01-01

    Hexavalent chromium or chromium (VI) is a powerful epithelial irritant and a confirmed human carcinogen. This heavy metal is toxic to many plants, aquatic animals, and bacteria. Chromium (VI) which consists of 10%-15% total chromium usage, is principally used for metal plating (H2Cr2O7), as dyes, paint pigments, and leather tanning, etc. Industrial production of chromium (II) and (III) compounds are also available but in small amounts as compared to chromium (VI). Chromium (VI) can act as an oxidant directly on the skin surface or it can be absorbed through the skin, especially if the skin surface is damaged. The prooxidative effects of chromium (VI) inhibit antioxidant enzymes and deplete intracellular glutathione in living systems and act as hematotoxic, immunotoxic, hepatotoxic, pulmonary toxic, and nephrotoxic agents. In this review, we particularly address the hexavalent chromium-induced generation of reactive oxygen species and increased lipid peroxidation in humans and animals, and the possible role of garlic (Allium sativum Linn) as a protective antioxidant. PMID:22865357

  1. Biosorption and biotransformation of chromium by Serratia sp. isolated from tannery effluent.

    Science.gov (United States)

    Srivastava, Shaili; Thakur, Indu Shekhar

    2012-01-01

    A bacterium isolated from soil and sediment ofa leather tanning mill's effluent was identified as Serratia sp. by the analysis of 16S rDNA. Scanning electron microscopy-energy dispersive X-ray analysis (SEM-EDX) and transmission electron microscopy (TEM) were used to assess morphological changes and confirm chromium biosorption in Serratia sp. both in a shake-flask culture containing chromium and in a tannery wastewater. The SEMEDX and the elemental analysis of the chromate-containing samples confirmed the binding of chromium with the bacterial biomass. The TEM exhibited chromium accumulation throughout the bacterial cell, with some granular deposits in the cell periphery and in the cytoplasm. X-ray diffraction analysis (XRD) was used to quantify the chromium and to determine the chemical nature of the metal-microbe interaction. The XRD data showed the crystalline character of the precipitates, which consisted of mainly calcium chromium oxide, chromium fluoride phosphate and related organo-Cr(III) complex crystals. The XRD data also revealed a strong involvement of cellular carboxyl and phosphate groups in chromium binding by the bacterial biomass. The results of the study indicated that a combined mechanism of ion-exchange, complexation, croprecipitation and immobilization was involved in the biosorption of chromium by bacterial cells in contaminated environments. PMID:22519094

  2. Chromium recovery from exhausted baths generated in plating processes and its reuse in the tanning industry.

    Science.gov (United States)

    Torras, Josep; Buj, Irene; Rovira, Miquel; de Pablo, Joan

    2012-03-30

    Chromium plating used for functional purposes provides an extremely hard, wear and corrosion resistant layer by means of electrolytic deposition. Typical layer thicknesses range between 2.5 and 500 μm. Chromium electroplating baths contain high concentrations of Cr(VI) with chromium trioxide (CrO(3)) as the chromium source. When because of technical or economic reasons a bath gets exhausted, a waste containing mainly chromium as dichromate as well as other heavy metals is generated. Chromium may then be purified for use in other industrial processes with different requirements. In this work, a sustainable system for using galvanic wastes as reagents in the leather tanning industry, thus reducing quantity of wastes to be treated, is presented. Metal cations present in the chromium exhausted bath were precipitated with NaOH. Then, the solution containing mainly soluble Cr(VI) was separated. By means of sodium sulphite in acidic conditions, Cr(VI) was reduced to Cr(III) as chromium (III) sulphate. From chromium (III) sulphate a basic Cr(III) sulphate may be obtained, which is one of most used compounds in the tanning industry. Cr(III) concentration in the final solution allows its reuse without concentration, but with a slight dilution. PMID:22326242

  3. Simultaneous Speciation of Arsenic, Selenium, and Chromium by HPLC-ICP-MS

    Science.gov (United States)

    Wolf, Ruth E.; Morman, Suzette A.; Morrison, Jean M.; Lamothe, Paul J.

    2008-01-01

    An adaptation of an analytical method developed for chromium speciation has been utilized for the simultaneous determination of As(III), As(V), Se(IV), Se(VI), Cr(III), and Cr(VI) species using high performance liquid chromatography (HPLC) separation with ICP-MS detection. Reduction of interferences for the determination of As, Se, and Cr by ICP-MS is a major consideration for this method. Toward this end, a Dynamic Reaction Cell (DRC) ICP-MS system was used to detect the species eluted from the chromatographic column. A variety of reaction cell gases and conditions may be utilized, and the advantages and limitations of the gases tested to date will be presented and discussed. The separation and detection of the As, Se, and Cr species of interest can be achieved using the same chromatographic conditions in less than 2 minutes by complexing the Cr(III) with EDTA prior to injection on the HPLC column. Practical aspects of simultaneous speciation analysis will be presented and discussed, including issues with HPLC sample vial contamination, standard and sample contamination, species stability, and considerations regarding sample collection and preservation methods. The results of testing to determine the method's robustness to common concomitant element and anion effects will also be discussed. Finally, results will be presented using the method for the analysis of a variety of environmental and geological samples including waters, soil leachates and simulated bio-fluid leachates.

  4. Kinetics and mechanism of hexavalent chromium removal by basic oxygen furnace slag.

    Science.gov (United States)

    Han, Chong; Jiao, Yanan; Wu, Qianqian; Yang, Wangjin; Yang, He; Xue, Xiangxin

    2016-08-01

    Basic oxygen furnace slag (BOFS) has the potential to remove hexavalent chromium (Cr(VI)) from wastewater by a redox process due to the presence of minerals containing Fe(2+). The effects of the solution pH, initial Cr(VI) concentration, BOFS dosage, BOFS particle size, and temperature on the removal of Cr(VI) was investigated in detail through batch tests. The chemical and mineral compositions of fresh and reacted BOFS were characterized using scanning electron microscope (SEM) equipped with an energy dispersive spectrometer (EDS) system and X-ray diffractometer (XRD). The results show that Cr(VI) in wastewater can be efficiently removed by Fe(2+) released from BOFS under appropriate acidic conditions. The removal of Cr(VI) by BOFS significantly depended on the parameters mentioned above. The reaction of Cr(VI) with BOFS followed the pseudo-second-order kinetic model. Fe(2+) responsible for Cr(VI) removal was primarily derived from the dissolution of FeO and Fe3O4 in BOFS. When H2SO4 was used to adjust the solution acidity, gypsum (CaSO4·2H2O) could be formed and become an armoring precipitate layer on the BOFS surface, hindering the release of Fe(2+) and the removal of Cr(VI). Finally, the main mechanism of Cr(VI) removal by BOFS was described using several consecutive reaction steps. PMID:27521937

  5. THE INFLUENCE OF CHEMICAL COMPOSITION OF HIGH-CHROMIUM CAST IRONS ON THE MACHINABILITY

    Directory of Open Access Journals (Sweden)

    V. V. Netrebko

    2016-02-01

    Full Text Available Purpose. This research is aimed to obtain the regression dependence of the machinability on the chemical composition of pig iron (C, Cr, Mn and Ni in cast state. Methodology. The method of active experiment planning was used to build a mathematical model. Cast irons of composition 1.09…3.91 % С; 11.43…25.57 % Cr; 0.6…5.4 % Mn; 0.19…3.01 % Ni were studied. Cutting tools with plates 10х10 mm out of ВК8 according to State Standard 19051-80 were used for turning. Cutting modes: cutting depth – 0.8 mm, longitudinal feed – 0.15 mm/rot., spindle’s rotation frequency during turning – 200…360 rot./min. Lubricating and cooling liquids were not applied. Evaluation of iron workability was produced by determining the linear tool flank wear per unit length of the cutting path. Findings. Mathematically probabilistic equation of the regression dependence of the cutting tool’s wear on the C, Cr, Mn and Ni content in the machined cast iron were obtained. It was established that with the increase of Cr content in the cast iron to 14.8 % the cutting tool’s wear decreased as a result of formation of carbide eutectic which destroyed the doped ledeburite continuous frame. Further increase of chromium content promoted appearing of chromic carbides with high microhardness which considerably increased the tool’s wear. The conducted research shown that the minimum cutting tool’s wear 0,18 mkm/m was observed during the machining of cast iron containing: 1.09 % C, 14.8 % Cr, 2.3 % Mn and 1.2 % Ni; and the maximum wear is 48,96 mkm/m – when the content was: 3.91 % C, 11.43 % Cr, 5.4 % Mn and 0.19 % Ni. The tool’s wear reached 47.61 mkm/m during the treatment of cast iron containing 3.91 % C, 25.57 % Cr, 5.4 % Mn and 0.19 % Ni. Originality. Mathematically probabilistic model of the dependence of the cutting tool’s wear on the C, Cr, Mn and Ni content in the machined cast iron has been elaborated by the author. Practical value. The model

  6. Safety and efficacy of cobalt chromium alloy based sirolimus-eluting stent with bioabsorbable polymer in porcine model

    Institute of Scientific and Technical Information of China (English)

    WU Yi-zhe; SHEN Li; WANG Qi-bing; HU Xi; XIE Jian; QIAN Ju-ying; GE Jun-bo

    2012-01-01

    Background First generation drug-eluting stents (DESs) were based on 316L stainless steel and coated with a permanent polymer.The vessel wall of these DESs was inflammatory and late in-stent thrombosis was reported.Hence,cobalt chromium based DES coated with a bioabsorbable polymer was an alternate choice.Methods Cobalt chromium based DES with bioabsorbable polymer (Simrex stent) as well as control stents (Polymer stent and EXCELTM stent) were implanted into porcine arteries.At a designated time,angiography,quantitative coronary angiography (QCA) analysis,histomorphometry,and electron-microscopical follow-up were performed.Results A total of 98 stents of all the three groups were harvested.At week 24,percent diameter stenosis (%DS),late loss (LL),and percent area stenosis (%AS) of Simrex was (12.9±0.4)%,(0.35±0.02) mm,and (24.5±4.2)%,respectively,without significant difference in comparison to commercialized EXCELTM stent.Slight inflammatory reaction was seen around the stent strut of Simrex,just as in the other two groups.Electron-microscopical follow-up suggested that it might take 4-12 weeks for Simrex to complete its re-endothelialization process.Conclusions Cobalt chromium based,bioabsorbable polymer coated sirolimus-eluting stent showed excellent biocompatibility.During 24 weeks observation in porcine model,it was proved that this novel DES system successfully inhibited neointima hyperplasia and decreased in-stent stenosis.It is feasible to launch a clinical evaluation to improve the current prognosis of DES implantation.

  7. Airborne exposure to inhalable hexavalent chromium in welders and other occupations: Estimates from the German MEGA database.

    Science.gov (United States)

    Pesch, Beate; Kendzia, Benjamin; Hauptmann, Kristin; Van Gelder, Rainer; Stamm, Roger; Hahn, Jens-Uwe; Zschiesche, Wolfgang; Behrens, Thomas; Weiss, Tobias; Siemiatycki, Jack; Lavoué, Jerome; Jöckel, Karl-Heinz; Brüning, Thomas

    2015-07-01

    This study aimed to estimate occupational exposure to inhalable hexavalent chromium (Cr(VI)) using the exposure database MEGA. The database has been compiling Cr(VI) concentrations and ancillary data about measurements at German workplaces. We analysed 3659 personal measurements of inhalable Cr(VI) collected between 1994 and 2009. Cr(VI) was determined spectrophotometrically at 540 nm after reaction with diphenylcarbazide. We assigned the measurements to pre-defined at-risk occupations using the information provided about the workplaces. Two-thirds of the measurements were below the limit of quantification (LOQ) and multiply imputed according to the distribution above LOQ. The 75th percentile value was 5.2 μg/m(3) and the 95th percentile was 57.2 μg/m(3). We predicted the geometric mean for 2h sampling in the year 2000, and the time trend of Cr(VI) exposure in these settings with and without adjustment for the duration of measurements. The largest dataset was available for welding (N = 1898), which could be further detailed according to technique. The geometric means were above 5 μg/m(3) in the following situations: spray painting, shielded metal arc welding, and flux-cored arc welding if applied to stainless steel. The geometric means were between 1 μg/m(3) and 5 μg/m(3) for gas metal arc welding of stainless steel, cutting, hard-chromium plating, metal spraying and in the chemical chromium industry. The exposure profiles described here are useful for epidemiologic and industrial health purposes. Exposure to Cr(VI) varies not only between occupations, but also within occupations as shown for welders. In epidemiologic studies, it would be desirable to collect exposure-specific information in addition to the job title. PMID:25979374

  8. 41 CFR 105-54.308 - Responsibilities of the Administrator.

    Science.gov (United States)

    2010-07-01

    ... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Responsibilities of the Administrator. 105-54.308 Section 105-54.308 Public Contracts and Property Management Federal Property... of the Administrator. The Administrator must ensure: (a) Compliance with the Federal...

  9. 27 CFR 5.4 - Delegations of the Administrator.

    Science.gov (United States)

    2010-04-01

    ... the Administrator's Authorities in 27 CFR Part 5, Labeling and Advertising of Distilled Spirits. You... Administrator. 5.4 Section 5.4 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU... the Administrator. Most of the regulatory authorities of the Administrator contained in this part...

  10. 42 CFR 488.54 - Temporary waivers applicable to hospitals.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 5 2010-10-01 2010-10-01 false Temporary waivers applicable to hospitals. 488.54... Requirements § 488.54 Temporary waivers applicable to hospitals. (a) General provisions. If a hospital is found to be out of compliance with one or more conditions of participation for hospitals, as specified...

  11. 27 CFR 21.54 - Formula No. 27-B.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Formula No. 27-B. 21.54... OF THE TREASURY LIQUORS FORMULAS FOR DENATURED ALCOHOL AND RUM Specially Denatured Spirits Formulas and Authorized Uses § 21.54 Formula No. 27-B. (a) Formula. To every 100 gallons of alcohol add:...

  12. 32 CFR 516.54 - Witnesses for the United States.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 3 2010-07-01 2010-07-01 true Witnesses for the United States. 516.54 Section 516.54 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY AID OF CIVIL AUTHORITIES AND PUBLIC RELATIONS LITIGATION Release of Information and Appearance of Witnesses Scope Status, Travel, and Expenses of Witnesses §...

  13. 49 CFR 230.54 - Testing and maintenance.

    Science.gov (United States)

    2010-10-01

    ..., DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS Boilers and Appurtenances Water Glasses and Gauge Cocks § 230.54 Testing and maintenance. (a) Testing. All water glasses must be... 49 Transportation 4 2010-10-01 2010-10-01 false Testing and maintenance. 230.54 Section...

  14. Registration of EL54 and EL55 sugarbeet germplasms

    Science.gov (United States)

    EL54 (PI 654357) is a sugarbeet germplasm derived from wild beet (Beta vulgaris ssp. maritima) accession WB879 (PI 540625), released in the interest of broadening the genetic base of sugar beet. The parent accession WB879, collected in 1989 from Port-de-Houet, France. EL54 has shown excellent Aphan...

  15. 40 CFR 406.54 - Pretreatment standards for existing sources.

    Science.gov (United States)

    2010-07-01

    ... introduces process wastewater pollutants into a publicly owned treatment works must comply with 40 CFR part... sources. 406.54 Section 406.54 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GRAIN MILLS POINT SOURCE CATEGORY Normal Rice Milling Subcategory §...

  16. 28 CFR 54.130 - Effect of employment opportunities.

    Science.gov (United States)

    2010-07-01

    ... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Effect of employment opportunities. 54... § 54.130 Effect of employment opportunities. The obligation to comply with these Title IX regulations is not obviated or alleviated because employment opportunities in any occupation or profession are...

  17. 42 CFR 71.54 - Etiological agents, hosts, and vectors.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 1 2010-10-01 2010-10-01 false Etiological agents, hosts, and vectors. 71.54..., INSPECTION, LICENSING FOREIGN QUARANTINE Importations § 71.54 Etiological agents, hosts, and vectors. (a) A... any arthropod or other animal host or vector of human disease, or any exotic living arthropod or...

  18. 44 CFR 5.54 - Denial of request of records.

    Science.gov (United States)

    2010-10-01

    ... 44 Emergency Management and Assistance 1 2010-10-01 2010-10-01 false Denial of request of records. 5.54 Section 5.54 Emergency Management and Assistance FEDERAL EMERGENCY MANAGEMENT AGENCY... within a specified number of days, when the search or examination is expected to be complete. The...

  19. 7 CFR 905.54 - Marketing, research and development.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Marketing, research and development. 905.54 Section 905.54 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE...

  20. 46 CFR 310.54 - General requirements for eligibility.

    Science.gov (United States)

    2010-10-01

    ...), Merchant Marine Act, 1936, as amended (46 U.S.C. 1114(b)); Pub. L. 97-31 (August 6, 1981); 49 CFR 1.66) ....54 Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION TRAINING MERCHANT MARINE TRAINING Admission and Training of Midshipmen at the United States Merchant Marine Academy § 310.54...

  1. 50 CFR 86.54 - How must I submit proposals?

    Science.gov (United States)

    2010-10-01

    ... 50 Wildlife and Fisheries 6 2010-10-01 2010-10-01 false How must I submit proposals? 86.54 Section...) PROGRAM How States Apply for Grants § 86.54 How must I submit proposals? (a) You may apply for either Tier One funding or Tier Two funding or both. (b) You may submit more than one project proposal within...

  2. 33 CFR 401.54 - Interference with navigation aids.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Interference with navigation aids. 401.54 Section 401.54 Navigation and Navigable Waters SAINT LAWRENCE SEAWAY DEVELOPMENT CORPORATION... with navigation aids. (a) Aids to navigation shall not be interfered with or used as moorings. (b)...

  3. 41 CFR 105-54.203-2 - Active charters file.

    Science.gov (United States)

    2010-07-01

    ... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Active charters file. 105-54.203-2 Section 105-54.203-2 Public Contracts and Property Management Federal Property Management... charters file. The GSA Committee Management Officer retains each original signed charter in a file...

  4. 7 CFR 1218.54 - Programs, plans, and projects.

    Science.gov (United States)

    2010-01-01

    ... marketing of fresh and processed blueberries, and the creation of new products thereof, to the end that the... 7 Agriculture 10 2010-01-01 2010-01-01 false Programs, plans, and projects. 1218.54 Section 1218.54 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL...

  5. 27 CFR 8.54 - Criteria for determining retailer independence.

    Science.gov (United States)

    2010-04-01

    ... retailer independence. 8.54 Section 8.54 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND... determining retailer independence. The criteria specified in this section are indications that a particular practice, other than those in §§ 8.52 and 8.53, places retailer independence at risk. A practice need...

  6. 42 CFR 54a.5 - Religious character and independence.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 1 2010-10-01 2010-10-01 false Religious character and independence. 54a.5 Section... ABUSE PREVENTION AND TREATMENT SERVICES § 54a.5 Religious character and independence. A religious organization that participates in an applicable program will retain its independence from Federal, State,...

  7. 29 CFR 1960.54 - Training of top management officials.

    Science.gov (United States)

    2010-07-01

    ... PROGRAMS AND RELATED MATTERS Training § 1960.54 Training of top management officials. Each agency shall provide top management officials with orientation and other learning experiences which will enable them to... 29 Labor 9 2010-07-01 2010-07-01 false Training of top management officials. 1960.54 Section...

  8. The sigma(54) regulon (sigmulon) of Pseudomonas putida

    DEFF Research Database (Denmark)

    Cases, I.; Ussery, David; de Lorenzo, V.

    2003-01-01

    methods, the sigma(54) regulon has been studied both in Escherichia coli, Salmonella typhimurium and several species of the Rhizobiaceae. Here we present the analysis of the sigma(54) regulon (sigmulon) in the complete genome of Pseudomonas putida KT2440. We have developed an improved method for the...

  9. 22 CFR 96.54 - Placement standards in outgoing cases.

    Science.gov (United States)

    2010-04-01

    ... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Placement standards in outgoing cases. 96.54 Section 96.54 Foreign Relations DEPARTMENT OF STATE LEGAL AND RELATED SERVICES ACCREDITATION OF AGENCIES... print, media, and internet resources designed to communicate with potential prospective adoptive...

  10. 47 CFR 54.502 - Supported telecommunications services.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 3 2010-10-01 2010-10-01 false Supported telecommunications services. 54.502 Section 54.502 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES... telecommunications services. For purposes of this subpart, supported telecommunications services provided...

  11. 7 CFR 54.1016 - Advance information concerning service rendered.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Advance information concerning service rendered. 54..., Processing, and Packaging of Livestock and Poultry Products § 54.1016 Advance information concerning service... MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE...

  12. 7 CFR 54.15 - Advance information concerning service rendered.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Advance information concerning service rendered. 54.15... Service § 54.15 Advance information concerning service rendered. Upon request of any applicant, all or any... SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED)...

  13. 26 CFR 54.4980G-4 - Calculating comparable contributions.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 17 2010-04-01 2010-04-01 false Calculating comparable contributions. 54.4980G-4 Section 54.4980G-4 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY... calendar year. (c) Model notice. Employers may use the following sample language as a basis in...

  14. 46 CFR 54.30-5 - Limitations and requirements.

    Science.gov (United States)

    2010-10-01

    ... VIII of the ASME Boiler and Pressure Vessel Code (incorporated by reference; see 46 CFR 54.01-1) and have a ratio of yield to ultimate tensile strength not greater than 0.8. For example: A-537 steels... out at a pressure higher than that required by § 54.30-10(a)(1) and an experimental strain analysis...

  15. 7 CFR 925.54 - Special purpose shipments.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Special purpose shipments. 925.54 Section 925.54 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing... entering the channels of trade for other than the specific purposes authorized by this section....

  16. Water-Rock Interaction and the Hydrogeochemistry of Chromium in Groundwater from Multilevels Monitoring Wells in Urania, SP, Brazil

    Directory of Open Access Journals (Sweden)

    Reginaldo Antonio Bertolo

    2009-06-01

    Full Text Available Anomalous natural concentrations of chromium, sometimes exceeding the potability limit (0.05 mg.L-1, have been detectedin the groundwater of Adamantina Aquifer in the municipality of Urânia, and in a wide region of the western part ofthe State of São Paulo. In order to identify the possible geochemical reactions that may explain the occurrence of chromiumin groundwater, chemical and mineralogical analyses were conducted in rock samples collected from deep boreholes drilledin the city of Urânia. Multilevel monitoring wells were installed in the boreholes, and stratifi ed groundwater samples werecollected for chemical analyses. The analyses of the borehole samples indicated the occurrence of a geochemical anomaly ofchromium (average concentrations of 221 ppm and pointed to chrome-diopside containing from 1,000 to 6,000 ppm Cr as themain reactive mineral that contributes to this anomaly. Groundwater chemical analyses indicated the occurrence of a hydrochemicalstratifi cation of the aquifer: waters from the base of the aquifer are alkaline (pH higher than 10 whereas in the shallowzone of the aquifer, pH is neutral to mildly acid. Chromium has been identifi ed in its hexavalent form, and prevails in theaquifer, reaching the maximum concentration of 0.13 mg.L-1. The geochemical reactions that explain the release of chromiumfrom the solid phase to the water probably involve the dissolution of Cr3+ minerals such as diopside, followed by a redox reactionthat oxidizes Cr3+ to Cr6+ and reduces manganese oxide minerals. Additionally, adsorption reactions may take place, anddesorption and mobilization of Cr6+ may be favored in some portions of the deep aquifer where pH is anomalously alkaline.

  17. Influence of cobalt and chromium additions on the precipitation processes in a Cu-4Ti alloys; Influencia de la adicion de cobalto y cromo en el proceso de precipitacion en una aleacion de Cu-4Ti

    Energy Technology Data Exchange (ETDEWEB)

    Donoso, E.

    2010-07-01

    The influence of 0.5% atomic cobalt and 1% atomic chromium additions on the precipitation hardening of Cu-4Ti alloy was studied by differential scanning calorimetry (DSC) and microhardness measurements. The analysis of the calorimetric curves, for binary alloy, shows the presence of two overlapping exothermic reactions (stages 1 and 2) attributed to the formation of Cu{sub 4}Ti and Cu{sub 3}Ti particles in the copper matrix, respectively. DSC curves for Cu-4Ti-0.5Co alloy shows three exothermic effects (overlapping stages 3 and 4 and stage 5) associated to the formation of phases Ti{sub 2}Co, TiCo and Cu{sub 4}Ti, respectively. DSC curves for Cu-4Ti1Cr alloy shows three exothermic reactions (stages 6, 7 and 9) and one endothermic peak (stage 8). The exothermic reactions correspond to the formation of phases Cr{sub 2}Ti, Cu{sub 4}Ti and Cu{sub 3}Ti, respectively, and the endothermic reactions are attributed to the Cr{sub 2}Ti dissolution. The activation energies calculated using the modified Kissinger method were lower than the ones corresponding to diffusion of cobalt, chromium, and titanium in copper. Kinetic parameters were obtained by a convolution method based on the Johnson-Mehl-Avrami (JMA) formalism. Microhardness measurements confirmed the formation of the mentioned phases. Also, these measurements confirmed the effect of cobalt and chromium addition on the binary alloy hardness. (Author). 31 refs.

  18. Impact of incorporation of chromium on electrochemical properties of LiFePO4/C for Li-ion batteries

    Directory of Open Access Journals (Sweden)

    Naik Amol

    2015-12-01

    Full Text Available LiFe0.95Cr0.05PO4/C was successfully synthesized by one-step solid-state reaction using a single mode microwave reactor. The effect of incorporation of chromium on LiFePO4 lattice parameters was systematically investigated by X-ray diffraction. Surface analysis was done by scanning electron microscopy and transmission electron microscopy. The ratio of amorphous to graphitic carbon was determined from Raman spectroscopic data. The influence of chromium incorporation on electrochemical properties was studied by recording charge/discharge cycles combined with electrochemical impedance spectroscopy (EIS and cyclic voltammetry. It was found that Cr incorporation significantly enhanced the electrochemical performance of LiFePO4 at all current densities up to 10 C. LiFe0.95Cr0.05PO4/C prepared exhibited the best performance with an initial specific discharge capacity of 157.7, 144.8, 138.3, 131.0, 124.1 and 111.1 mAh·g−1 at 0.1 C, 0.5 C, 1.0 C, 2.0 C, 5 C and 10 C, respectively. The doped sample displayed excellent capacity retention, which was substantially superior than that of pristine LiFePO4/C at a higher current rate.

  19. Magnetic and structural properties of nanosize Ni-Zn-Cr ferrite particles synthesized by combustion reaction

    Energy Technology Data Exchange (ETDEWEB)

    Gama, L. [Department of Materials Engineering, Federal University of Campina Grande, 58970-000 Campina Grande, PB (Brazil)]. E-mail: lucianna@dema.ufcg.edu.br; Hernandez, E.P. [Department of Physics, Federal University of Pernambuco, 50670-901 Recife, PE (Brazil); Cornejo, D.R. [Institute of Physics, University of Sao Paulo, 05508-900 Sao Paulo, SP (Brazil)]. E-mail: cornejo@macbeth.if.usp.br; Costa, A.A. [Department of Physics, Federal University of Pernambuco, 50670-901 Recife, PE (Brazil)]. E-mail: aac@df.ufpe.br; Rezende, S.M. [Department of Physics, Federal University of Pernambuco, 50670-901 Recife, PE (Brazil)]. E-mail: rezende@df.ufpe.br; Kiminami, R.H.G.A. [Department of Materials Engineering, Federal University of Sao Carlos, 13565-905 Sao Carlos, SP (Brazil)]. E-mail: ruth@powder.ufscar.br; Costa, A.C.F.M. [Department of Materials Engineering, Federal University of Campina Grande, 58970-000 Campina Grande, PB (Brazil)]. E-mail: anacristina@dema.ufcg.edu.br

    2007-10-15

    This paper reports on Cr{sup 3+}-doped and undoped Ni-Zn nanosize ferrite obtained by reaction combustion synthesis. The powders resulting from this synthesis were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM), and their magnetic properties examined with an alternative gradient magnetometer (AGM) and by ferromagnetic resonance (FMR). The XRD results confirmed the formation of Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} bulk spinel and small quantities of second phase hematite ({alpha}Fe{sub 2}O{sub 4}) to the powders without chromium. However, the powders containing 0.1 mol of chromium showed only a Ni-Zn ferrite cubic phase. The Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} and Ni{sub 0.5}Zn{sub 0.5}Fe{sub 1.9}Cr{sub 0.1}O{sub 4} showed average crystallite sizes of 20.7 and 22.7 nm, respectively. The SEM micrographs of the powders to the sample without chromium reveals nanoparticles with a regular morphology without pre-sintering and with the presence of soft agglomerations. The powder with 0.1 mol of chromium displays homogeneous and finer nanoparticles, which are more reactive and hence more agglomerated. Saturation magnetization of the phase without Cr{sup 3+} was 61.97 emu/g, while that of the powder with chromium was 40.56 emu/g. The inclusion of chromium caused the magnetization index to drop by 34% and decreased the coercive field, H {sub c}, by 77%. It is known that the inclusion of chromium is advantageous for high-frequency transformer applications.

  20. Thermal stabilization of chromium(VI) in kaolin.

    Science.gov (United States)

    Wei, Yu-Ling; Chiu, Shu-Yuan; Tsai, Hsien-Neng; Yang, Yaw-Wen; Lee, Jyh-Fu

    2002-11-01

    Reduction of Cr(VI) by heating may be a useful detoxification mechanism for thermal immobilization. Using X-ray absorption spectroscopy, the change of speciation of chromium in 105 degrees C dried 3.7% Cr(VI)-sorbed kaolin further heated at 500, 900, or 1100 degrees C was studied. The 105 degrees C dried 3.7% Cr(VI)-sorbed kaolin sample was prepared by mixing 1.5 L of 0.257 M CrO3 solution (pH 0.71) with 0.5 kg of kaolin powder for 48 h, and then the slurry was heated (dried) at 105 degrees C until a constant weight was reached. The toxicity characteristic leaching procedure method was used to determine the percentage of leached chromium from all heated samples. In all 500-900 degrees C heated Cr(VI)-sorbed kaolin samples, Cr2O3 transformed from the hydrated Cr(VI) by a 4-h heat application was identified by the X-ray absorption near edge structure and extended X-ray absorption fine structure (EXAFS) spectroscopy as the key species that is leaching-resistant due to its low solubility. For the 1100 degrees C heated Cr(VI)-sorbed kaolin sample, the Fourier transform of its EXAFS spectrum indicates that the intensity of the peaks at 2.45 (Cr-Cr shell of Cr2O3) and 5.00 A (Cr-Cr and Cr-O shells of Cr2O3) without phase shift correction is either relatively smaller or disappearing, compared with that of the 500-900 degrees C heated Cr(VI)-sorbed kaolin samples. It is suggested that chromium octahedra were bridged to silica tetrahedra and incorporated in minerals formed at 1100 degrees C, such as mullite or sillimanite, since these phases were detected by XRD. Cr of this form is not easily leached. PMID:12433175

  1. Chromium Isotopes Record Fluctuations in Precambrian Biospheric Oxygenation

    Science.gov (United States)

    Frei, R.; Gaucher, C.; Poulton, S. W.; Canfield, D. E.

    2009-12-01

    There is a direct relationship between life, oxygen, and the surface chemistry of the Earth. Geochemical data suggest that oxygenation of the Earth's atmosphere occurred in two broad steps, near the beginning and the end of the Proterozoic Eon (2500 to 542 million years ago), but the details of this history are unclear. The geochemical behaviour of chromium (Cr) is highly sensitive to the redox state of the surface environment as oxidative weathering processes produce the oxidised hexavalent [Cr(VI)] form. Oxidation of reduced trivaltent [Cr(III)] chromium on land is accompanied by an isotopic fractionation, leading to enrichment of the mobile hexavalent form in the heavier isotope. The fractionated Cr isotope signature is then tranfered by riverine transport to the sea. Here, we use Cr stable isotopes from banded iron formations (BIFs) to track the presence of Cr(VI) in Precambrian oceans, providing a time-resolved picture of the oxygenation history of Earth’s atmosphere-hydrosphere system. Fractionated Cr isotopes indicate the accumulation of Cr(VI) in ocean surface waters ~2.8 to 2.6 billion years (Gyr) ago and a likely transient elevation in atmospheric and surface ocean oxygen prior to the first great rise of oxygen 2.45-2.2 Gyr ago (the Great Oxidation Event; GOE). In contrast, Cr isotopes in ~1.88 Gyr old BIFs are not fractionated, indicating a major decline in atmospheric oxygen and demonstrating that the GOE did not lead to a unidirectional stepwise increase in atmospheric oxygen. In the late Neoproterozoic, ~800 to 542 million years (Myr) ago, we observe strong positive fractionations in Cr isotopes (δ53Cr up to +4.9 ‰) providing independent support for increased surface oxygenation at this time. This may have stimulated rapid evolution of macroscopic multicellular life. Our chromium isotope data thus provide new insights into the oxygenation history of the Earth, and highlight its use as a powerful redox tracer in aquatic systems.

  2. Light induced electron transfer reactions of metal complexes

    International Nuclear Information System (INIS)

    Properties of the excited states of tris(2,2'-bipyridine) and tris(1,10-phenanthroline) complexes of chromium(III), iron(II), ruthenium(II), osmium(II), rhodium(III), and iridium(III) are described. The electron transfer reactions of the ground and excited states are discussed and interpreted in terms of the driving force for the reaction and the distortions of the excited states relative to the corresponding ground states. General considerations relevant to the conversion of light into chemical energy are presented and progress in the use of polypyridine complexes to effect the light decomposition of water into hydrogen and oxygen is reviewed

  3. Ultrasound-assisted cloud point extraction for speciation and indirect spectrophotometric determination of chromium(III) and (VI) in water samples

    Science.gov (United States)

    Hashemi, Mahdi; Daryanavard, Seyed Mosayeb

    Ultrasound-assisted cloud point extraction (UACPE) procedure was developed for speciation and indirect spectrophotometric determination of chromium(III) and (VI) in environmental water samples. The method is based on the reduction of Cr(VI) by iodide in acidic media and subsequently formation of I3- anion. The I3- formed can further react with cetyltrimethylammonium bromide (CTAB) and induce its clouding due to formation of an ion-association complex. The formed complex was separated from solution and dissolved in ethanol for spectrophotometric measurement. Cerium(IV) ammonium sulphate was chosen as an oxidizing reagent for pre-oxidation step of Cr(III) to Cr(VI) species before the addition of iodide to the system, up to chromium in trivalent can be determined by the procedure. Experimental parameters for both spectrophotometric reaction and extraction procedure have been optimized. Under optimized conditions Cr(VI) can be determined in the range 20-400 ng mL-1 (R2 = 0.999). Detection limit, preconcentration factor and relative standard deviation were 12 ng mL-1, 20.0 and 2.2% (n = 5), respectively with 10 mL sample volumes. The proposed method has been successfully applied for determination of chromium(V) in spiked water, synthetic seawater and electroplating wastewater samples with average recoveries of 100.1, 99.4 and 99.1%, respectively.

  4. BIOSORPTION OF CHROMIUM (VI) FROM INDUSTRIAL EFFLUENT BY WILD ANDMUTANT TYPE STRAIN OF SACCHAROMYCES CEREVISIAE AND ITS IMMOBILIZED FORM

    OpenAIRE

    K Selvam, K Arungandhi, B Vishnupriya, T Shanmuga priya and M Yamuna

    2013-01-01

    Biosorption of chromium was studied by wild type Saccharomyces cerevisiae strain, mutant strain, immobilized-wild type and mutant strain. Chromium absorption pattern was observed in all experimental conditions. Hexavalent chromium (VI) was analyzed by diphenyl carbazide method, by oxidizing the trivalent chromium (III). The percentage efficiency of wild type S. cerevisiae and its mutant strain, immobilized-wild type and mutant strain were 94.8%, 98.7%, 97.4% and 100% respectively. S. cerevisi...

  5. Isocyanide and Phosphine Oxide Coordination in Binuclear Chromium Pacman Complexes.

    Science.gov (United States)

    Stevens, Charlotte J; Nichol, Gary S; Arnold, Polly L; Love, Jason B

    2013-12-01

    The new binuclear chromium Pacman complex [Cr2(L)] of the Schiff base pyrrole macrocycle H4L has been synthesized and structurally characterized. Addition of isocyanide, C≡NR (R = xylyl, (t)Bu), or triphenylphosphine oxide donors to [Cr2(L)] gives contrasting chemistry with the formation of the new coordination compounds [Cr2(μ-CNR)(L)], in which the isocyanides bridge the two Cr(II) centers, and [Cr2(OPPh3)2(L)], a Cr(II) phosphine oxide adduct with the ligands exogenous to the cleft.

  6. Chromium Renderserver: Scalable and Open Source Remote RenderingInfrastructure

    Energy Technology Data Exchange (ETDEWEB)

    Paul, Brian; Ahern, Sean; Bethel, E. Wes; Brugger, Eric; Cook,Rich; Daniel, Jamison; Lewis, Ken; Owen, Jens; Southard, Dale

    2007-12-01

    Chromium Renderserver (CRRS) is software infrastructure thatprovides the ability for one or more users to run and view image outputfrom unmodified, interactive OpenGL and X11 applications on a remote,parallel computational platform equipped with graphics hardwareaccelerators via industry-standard Layer 7 network protocolsand clientviewers. The new contributions of this work include a solution to theproblem of synchronizing X11 and OpenGL command streams, remote deliveryof parallel hardware-accelerated rendering, and a performance analysis ofseveral different optimizations that are generally applicable to avariety of rendering architectures. CRRSis fully operational, Open Sourcesoftware.

  7. Study on anaerobic treatment of wastewater containing hexavalent chromium*

    OpenAIRE

    Xu, Yan-Bin; Xiao, Hua-hua; Sun, Shui-yu

    2005-01-01

    A self-made anaerobic bio-filter bed which was inoculated with special sludge showed high efficiency in removing hexavalent chromium. When pump flow was 47 ml/min and CODCr of wastewater was about 140 mg/L, it took 4 h to decrease the Cr6+ concentrations from about 60 mg/L to under 0.5 mg/L, compared with 14 h without carbon source addition. Cr6+ concentrations ranged from 64.66 mg/L to 75.53 mg/L, the system efficiency was excellent. When Cr6+ concentration reached 95.47 mg/L, the treatment ...

  8. Alkaline stress corrosion of iron-nickel-chromium austenitic alloys

    International Nuclear Information System (INIS)

    This research thesis reports the study of the behaviour in stress corrosion of austenitic iron-nickel-chromium alloys by means of tensile tests at imposed strain rate, in a soda solution at 50 pc in water and 350 degrees C. The author shows that the mechanical-chemical model allows the experimental curves to be found again, provided the adjustment of characteristic parameters, on the one hand, of corrosion kinetics, and on the other hand, of deformation kinetics. A classification of the studied alloys is proposed

  9. Chromium Doped ZnS Nanostructures: Structural and Optical Characteristics

    Science.gov (United States)

    Gogoi, D. P.; Das, U.; Ahmed, G. A.; Mohanta, D.; Choudhury, A.; Stanciu, G. A.

    2009-06-01

    Chromium doped ZnS nanoparticles arranged in the form of fractals were fabricated by using inexpensive physico-chemical route. The Cr:ZnS samples were characterized by diffraction and spectroscopic techniques. Unexpected growth of fractals with several micrometer dimensions and of core size 1 μm (tip to tip) was confirmed through TEM micrographs. At higher magnification, we found that individual fractals consist of spherical nanoparticles of average size leading to such organized structures describing fractal pattern is encountered in this work.

  10. Evaluating Foraminifera as an Archive for Seawater Chromium Isotopic Composition

    Science.gov (United States)

    Wang, X.; Planavsky, N.; Hull, P. M.; Tripati, A.; Reinhard, C.; Zou, H.; Elder, L. E.; Henehan, M. J.

    2015-12-01

    In recent years there has been growing interest in using chromium isotopes (δ53Cr) as a proxy to investigate the redox evolution of Earth's ocean-atmosphere system throughout geological history. Potential archives for seawater δ53Cr that have been identified to date include iron formations and organic-rich siliciclastic sediments. However, these types of sediments are not common and they are discontinuous over geologic time. As a result, alternative types of archives are needed. Here we evaluate the utility of foraminifera tests as a recorder of seawater δ53Cr. Core-tops used were from different ocean basins. Mono-specific samples of Globigerinoides sacculifer, Orbulina universa, Pulleniatina obliquiloculata, Globoratalia crassula-crassaformis, Globoratalia truncatulinoides, and Globigerinella siphonifera were isolated to investigate inter-species isotope fractionation. Chromium concentrations were measured by isotope dilution method to be 0.1-0.3 μg/g. The δ53Cr values of these species range from 0.2‰ to 2.4‰, with an analytical uncertainty of 0.3‰ (95% confidence). Despite the high analytical uncertainty due to the extremely low levels of Cr present, there is still large detectable variation in foraminiferal δ53Cr values, which overlap presently available seawater values (Bonnand et al., 2013; Scheiderich et al., 2015). Possible explanations for such variations in foraminiferal δ53Cr values include heterogeneity of seawater δ53Cr in the modern oceans, and/or photobiochemical redox cycling of Cr in the surface oceans. Therefore, care should be taken when using foraminifera to reconstruct past seawater δ53Cr values. ReferencesBonnand, P., James, R., Parkinson, I., Connelly, D., Fairchild, I., 2013. The chromium isotopic composition of seawater and marine carbonates. Earth and Planetary Science Letters, 382: 10-20. Scheiderich, K., Amini, M., Holmden, C., Francois, R., 2015. Global variability of chromium isotopes in seawater demonstrated by Pacific

  11. Environmental optimization of chromium recovery from tannery sludge using a life cycle assessment approach.

    Science.gov (United States)

    Kiliç, Eylem; Puig, Rita; Baquero, Grau; Font, Joaquim; Colak, Selime; Gürler, Deniz

    2011-08-15

    Life cycle assessment (LCA) was used to evaluate the environmental impact of an oxidative chromium recovery method from tannery sludge, in comparison with the usual landfilling process. Three improvement options (water reduction, byproduct use and anaerobic sludge digestion) were considered. The results showed that the proposed chromium recovery process would be better environmentally than conventional landfilling in all the evaluated impact categories if the amount of chromium recovered was 43 kg per ton of sludge. This amount could be recovered if the chromium concentration was about 20 times higher than that considered in this study. Alternatively, a lower chromium concentration would produce a better result if the recovery method was optimized and implemented at industrial rather than laboratory scale, and if more accurate data were provided on environmental credits for avoiding the chromium production process. Thus, the recovery method is environmentally beneficial when tannery sludge contains a chromium concentration of about 100,000 ppm. According to the literature, such concentrations are not unusual. The results could serve as the basis for further environmental improvements in chromium recovery and tannery sludge management and should be used in decision-making processes, especially for end-of-pipe treatments.

  12. Evaluation of chromium concentration in cattle feces using different acid digestion and spectrophotometric quantification techniques

    Directory of Open Access Journals (Sweden)

    N.K.P. Souza

    2013-10-01

    Full Text Available The objective of this work was to evaluate combinations between acid digestion techniques and spectrophotometric quantification to measure chromium concentration in cattle feces. Digestion techniques were evaluated based on the use of nitric and perchloric acids, sulfuric and perchloric acids, and phosphoric acid. The chromium quantification in the solutions was performed by colorimetry and by atomic absorption spectrophotometry (AAS. When AAS was used, the addition of calcium chloride to the solutions as a releasing agent was also evaluated. Several standard samples containing known chromium contents were produced (0, 2, 4, 6, 8 and 10g of chromium per kg of feces using cattle feces obtained from three different animals to evaluate the accuracy of the different combinations of techniques. The accuracy was evaluated by adjusting a simple linear regression model of the estimated values on the actual values of chromium content in the standard samples. Regardless of the digestion technique, the chromium content estimates in the standard samples obtained by colorimetry were not accurate (P0.05. The use of the digestion technique in phosphoric acid provided incomplete recovery of the fecal chromium (P0.05 fecal chromium contents.

  13. Determination of hexavalent chromium in cosmetic products by ion chromatography and postcolumn derivatization.

    Science.gov (United States)

    Kang, Eun Kyung; Lee, Somi; Park, Jin-Hee; Joo, Kyung-Mi; Jeong, Hye-Jin; Chang, Ih Seop

    2006-05-01

    Chromium hydroxide green [Cr(2)O(OH)(4)] and chromium oxide green (Cr(2)O(3)) are colouring agents for use in cosmetic products. These colourants may contain chromium (VI), which cause skin allergies through percutaneous adsorption on the skin. Eye shadow is a representative cosmetic product in which significant colourants are used. We analysed the chromium (VI) in the eye shadows by ion chromatography and post column derivatization. We optimize conditions of chromium (VI) analysis in eye shadows. During the pretreatment procedure, there are no exchange of chromium (III) to chromium (VI). This method has a limit of quantification for chromium (VI) of 1.0 microg l(-1), recovery rate of 100 +/- 3% and analysis time less than 10 min. This result is 300 times more sensitive than the high-performance liquid chromatography method. We applied the optimized method to analyse 22 eye shadows and 6 colouring agents. 2 out of 22 of the products contained more than 5 mg l(-1). In our previous work, 5 mg l(-1) of Cr represented a threshold level. There was much more Cr(VI) in the colouring agents. The Cr(VI) in one of the colouring agents was 97.6 mg l(-1). PMID:16689807

  14. Suppression of interference in the AAS determination of chromium by use of ammonium bifluoride.

    Science.gov (United States)

    Purushottam, A; Naidu, P P; Lal, S S

    1973-07-01

    Addition of 1% of ammonium bifluoride successfully suppresses interference by diverse ions in the atomic-absorption determination of chromium(VI). If the sample solutions also contain chromium(III) addition of 1% of ammonium bifluoride and 0.2% of sodium sulphate is recommended for the suppression.

  15. Leaching behavior of chromium in chrome shaving generated in tanning process and its stabilization.

    Science.gov (United States)

    Erdem, Mehmet; Ozverdi, Arzu

    2008-08-15

    In this study, leaching properties and pollution potential of chromium in chrome shaving (CS), which is a solid residue of leather industry, containing 2.27% Cr were investigated and thermal stabilization procedure was applied to the CS for chromium immobilization. For this purpose, firstly, effects of the liquid/solid ratio, contact time, pH and sequential extraction on the leaching behavior of chromium in the CS were studied. It was determined that the CS-caused chromium pollution is a hazardous material for environment. Thermal stabilization procedure was applied to the CS in the temperature range of 250-500 degrees C for the chromium immobilization. Effective stabilization of chromium in the CS was achieved by heating of CS at 350 degrees C under CO(2) atmosphere. Leaching experiments were also carried out with the samples obtained from the stabilization process and the results compared with that of the CS. Also, TCLP test method was applied to the samples to determine pollution potentials and discharge situations of the CS and its stabilization products. While the chromium concentrations in the test solutions of all samples stabilized thermally at above 350 degrees C were below the USEPA regulatory limit of 5 mg/l, the concentration of chromium leached out from the CS was 30-fold bigger than the USEPA regulatory limit.

  16. The impact of humic acid on chromium phytoextraction by aquatic macrophyte Lemna minor.

    Science.gov (United States)

    Kalčíková, Gabriela; Zupančič, Marija; Jemec, Anita; Gotvajn, Andreja Žgajnar

    2016-03-01

    Studies assessing chromium phytoextration from natural waters rarely consider potential implications of chromium speciation in the presence of ubiquitous humic substances. Therefore, the present study investigated the influence of environmentally relevant concentration of humic acid (TOC = 10 mg L(-1)) on chromium speciation (Cr = 0.15 mg L(-1)) and consequently on phytoextraction by aquatic macrophyte duckweed Lemna minor. In absence of humic acid, only hexavalent chromium was present in water samples and easily taken up by L. minor. Chromium uptake resulted in a significant reduction of growth rate by 22% and decrease of chlorophyll a and chlorophyll b contents by 48% and 43%, respectively. On the other hand, presence of humic acid significantly reduced chromium bioavailability (57% Cr uptake decrease) and consequently it did not cause any measurable effect to duckweed. Such effect was related to abiotic reduction of hexavalent chromium species to trivalent. Hence, findings of our study suggest that presence of humic acid and chromium speciation cannot be neglected during phytoextraction studies. PMID:26766370

  17. 76 FR 71926 - Defense Federal Acquisition Regulation Supplement: Applicability of Hexavalent Chromium Policy to...

    Science.gov (United States)

    2011-11-21

    ... Acquisition Regulation Supplement: Applicability of Hexavalent Chromium Policy to Commercial Items (DFARS Case... hexavalent chromium. DATES: Comment Date: Comments on the proposed rule should be submitted in writing to the.... SUPPLEMENTARY INFORMATION: I. Background DoD published a final rule at in the Federal Register at 76 FR 25569...

  18. 77 FR 39141 - Defense Federal Acquisition Regulation Supplement: Applicability of Hexavalent Chromium Policy to...

    Science.gov (United States)

    2012-06-29

    ... Acquisition Regulation Supplement: Applicability of Hexavalent Chromium Policy to Commercial Items (DFARS Case... material containing hexavalent chromium. DATES: Effective Date: June 29, 2012. FOR FURTHER INFORMATION... published a final rule (DFARS Case 2009-D004) in the Federal Register at 76 FR 25569 on May 5, 2011,...

  19. 75 FR 69064 - Draft Toxicological Review of Hexavalent Chromium: In Support of Summary Information on the...

    Science.gov (United States)

    2010-11-10

    ... AGENCY Draft Toxicological Review of Hexavalent Chromium: In Support of Summary Information on the... period on September 30, 2010 (75 FR 60454) for the external review draft human health assessment titled, ``Toxicological Review of Hexavalent Chromium: In Support of Summary Information on the Integrated...

  20. The temperature gradient on section of casting in process of primary crystallization of chromium cast iron

    Directory of Open Access Journals (Sweden)

    A. Studnicki

    2008-08-01

    Full Text Available The methodology of defining in article was introduced the temperature gradient in process of primary crystallization during cooling the casting from chromium cast iron on basis of measurements of thermal field in test DTA-K3. Insert also the preliminary results of investigations of influence temperature gradient on structure of studied wear resistance chromium cast iron.