WorldWideScience

Sample records for chosa nenryo denchi

  1. Survey on commercial use of fuel cells; Nenryo denchi ni kansuru jitsuyoka no tame no chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The basic survey was carried out for the future approach to R & D of fuel cells. Phosphoric acid fuel cell (PAFC) is in the stage of demonstration research and field test supported by subsidy after the end of Sunshine project. Its reliability and durability problems are being solved, and its cost reduction is only one problem for practical use. Distributed systems or on-site systems will be used utilizing its excellent environmental characteristics. Molten carbonate fuel cell (MCFC), solid oxide one (SOFC) and polymer electrolyte one (PEFC) under development were thus surveyed. The following are surveyed: (1) Contribution to a human society such as improvement of energy demand/supply structure and environmental protection, (2) Technological items such as outlook for R & D, validity of developmental issues, comparison between various R & D and significance in industrial promotion, (3) Economic items such as profitability and feasible period, and (4) Social items such as sociability, compatibility to needs, possibility of locations, international meaning, market scale and promotion scenario. 90 refs., 67 figs., 96 tabs.

  2. FY 1999 report on the survey of the trend of the technology development of fuel cell vehicles; 1999 nendo chosa hokokusho. Nenryo denchi jidosha gijutsu kaihatsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    For the contribution to the introduction/spread of fuel cell vehicles, survey was conducted of the trend of technology development of fuel cell vehicles and the related infrastructure, the situation of the regulation/criteria, etc. As a typical project on the D and R of fuel cell vehicles in the U.S., cited is 'Partnership for a New Generation of Vehicles (PNGV)' which was commenced mainly by the US government and three US automobile manufacturers. The US DOE determined the introduction of a gasoline reforming type and has completed some prototype systems. In Europe, cited are 'Munich Airport Hydrogen Project,' Daimler-Chrysler's 'Transport Energy Strategy,' etc. In Japan, the introduction/promotion are being discussed in 'The New Sunshine Project' and 'The Millennium Project' proposed by former prime minister Obuchi. As to fuel cell vehicles, there are still many uncertain elements in performance, safety, economical efficiency, etc. Accordingly, the continued efforts should be made for the technology development for improvement of power performance, safety and economical efficiency and for the environmental arrangement of the infrastructure, introduction supporting system, etc. (NEDO)

  3. FY 1999 report on the survey of the trend of the technology development of fuel cell vehicles; 1999 nendo chosa hokokusho. Nenryo denchi jidosha gijutsu kaihatsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    For the contribution to the introduction/spread of fuel cell vehicles, survey was conducted of the trend of technology development of fuel cell vehicles and the related infrastructure, the situation of the regulation/criteria, etc. As a typical project on the D and R of fuel cell vehicles in the U.S., cited is 'Partnership for a New Generation of Vehicles (PNGV)' which was commenced mainly by the US government and three US automobile manufacturers. The US DOE determined the introduction of a gasoline reforming type and has completed some prototype systems. In Europe, cited are 'Munich Airport Hydrogen Project,' Daimler-Chrysler's 'Transport Energy Strategy,' etc. In Japan, the introduction/promotion are being discussed in 'The New Sunshine Project' and 'The Millennium Project' proposed by former prime minister Obuchi. As to fuel cell vehicles, there are still many uncertain elements in performance, safety, economical efficiency, etc. Accordingly, the continued efforts should be made for the technology development for improvement of power performance, safety and economical efficiency and for the environmental arrangement of the infrastructure, introduction supporting system, etc. (NEDO)

  4. Survey on construction of the database for new energy technology development. Fuel cell; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Nenryo denchi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    As a part of the data related to technological development of new energy, the database for fuel cells was prepared. The major international conferences held in fiscal 1996 were reviewed. As the atmosphere of the whole conference, phosphoric acid fuel cell (PAFC) is in a stage just before practical use, and molten carbonate fuel cell (MCFC) is in a stage of the demonstration study of MW class one. The study on solid oxide fuel cell (SOFC) and polymer electrolyte fuel cell (PEFC) is in considerable progress. In particular, the application of PEFC to automobiles is in real investigation. For the database, kinds and features of various fuel cells, operation principles, system configurations of FC plants, application fields, and characteristics were arranged. Field test examples for public and industrial uses were separately arranged, and in particular, the application examples of PAFC were presented together with developmental conditions of the other fuel cells. Overseas situations were equal to domestic ones, and their marketability was predicted. The Japanese subsidy policy and some U.S. policies were also arranged. 28 refs., 51 figs., 37 tabs.

  5. Investigation on preparing data collections related to new energy technology development. Fuel cells; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Nenryo denchi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    With an objective to put data related to fuel cells systematically into order, related data were collected comprehensively. Reviewing large international conferences impresses dawn of commercialization in phosphoric acid fuel cells (PAFC), take-off of megawatt-class molten carbonate fuel cells (MCFC), and remarkable advancement in studies on solid oxide fuel cells (SOFC) and polymer electrolyte fuel cells (PEFC). The data collection may be compiled as follows: basic principles, features, operation principles, system configurations, utilization fields, and characteristics were summarized on fuel cell power generation systems using phosphoric acid, polymer, molten carbonate, solid oxide, and alkaline fuel cells; major installation examples in Japan and overseas countries were summarized; investigations were given on developing other fuel cells such as alkaline type and direct methanol type fuel cells; and marketability, subsidies operations in Japan, and states of policy implementation in the U.S.A. were investigated and put into order. 22 refs., 24 figs., 21 tabs.

  6. Fiscal 1994 survey report. Survey of factors causing degradation of phosphoric acid fuel cells; 1994 nendo rinsangata nenryo denchi no cell rekka yoin chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    This survey aims to effectively promote studies for evaluating phosphoric acid fuel cell degradation. Data of time-dependent changes in voltage are collected from 58 plants now in operation (for 17,500 hours at the maximum). Half of them exhibit a degradation rate of 0.25-1%/1000 hours while degradation is abruptly accelerated midway in the other half. Causes for voltage drop are not known clearly. Since but a little systematically collected test data are available concerning the mechanism of cell degradation, it is decided that tests be conducted using small test model cells sharing the same specifications. Primary test conditions (combination of temperature, current, and pressure with test reference levels), performance evaluating methods (conditions of data collection), and methods of investigation by dismantling (items and frequency of investigations) are determined, and guidelines are provided for element tests for complementing the said test items and for studying their relations with the degradation mechanism. Based on acceleration-related factors to be obtained by common specification test cells, corporations involved will develop their own accelerated test methods. Small cells are fabricated for testing parameters, and model cells are specified. (NEDO)

  7. Data book on new energy technology development in FY 1997. Fuel cells; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Nenryo denchi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The purpose of this survey is to grasp the trends of technology development of fuel cells and their market, and to provide data required for supporting the introduction and diffusion of fuel cells. This report consists of Part 1 titled as `Trends of development of fuel cells in FY 1997`, and Part 2 titled as `Compiled data`. The Part 1 consists of three chapters, i.e., Chapter 1 titled as `Introduction`, Chapter 2 as `Development trends of fuel cells for on-site power generation`, and Chapter 3 as `Trends of development of fuel cells for mobile objects and fuel cell-powered vehicles`. The introductory chapter not only outlines the development trends but also describes the results of the 5th Grove Fuel Cell Symposium noticed as the major global international symposium on fuel cell in general and the environmental problems discussed at the COP3 Kyoto Conference, both held in TY 1997. The Part 2 contains the principles, system configurations and applications of fuel cells, PAFC, MCFC, SOFC, PEFC, modifier, DMFC, development trend of fuel cell-powered vehicles, and national policies for fuel cells in Japan. The Appendix features a report of the new technique investigation working group and information on fuel cells from newspapers. 100 refs., 4 figs.

  8. Fiscal 1998 research report. Survey on data collection for development of new energy technology (fuel cell); 1998 nendo chosa hokokusho. Shin energy gijutsu kaihatsu kankei data shu sakusei chosa (nenryo denchi)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report is composed of Part 1: the development trend of fuel cells in fiscal 1998, and Part 2: the collected data and appendices. Part 1 includes 4 chapters, (1) The outline of the development trend, (2) Stationary fuel cell, (3) The development trend of fuel cell vehicles, and (4) The development trend of small transportable fuel cells. The report newly includes the development trend of small-capacity fuel cells and the report on 1998 Fuel Cell Seminar notable as an international conference on fuel cell summarizing the trend of fuel cells in fiscal 1998, as compared with the fiscal 1997 report. Part 2 is the collected data on domestic and foreign demonstration operation results of fuel cells, and technical development of every fuel cell. In addition to various collected data on the whole of fuel cells and their use techniques, Part 2 includes the principle, features, system configuration, performance simulation technique, application and market analysis of fuel cells, and the national policy and concerned laws on a subsidy system for introduction of fuel cells, for example. (NEDO)

  9. Fiscal 2000 research report on the energy consumption survey for popularizing stationary fuel cell systems; 2000 nendo teichiyo nenryo denchi no fukyu wo mokutekito shita energy no shohi ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A survey was conducted about the current state of domestic energy consumption for studying the feasibility of a stationary energy system using the polymer electrolyte fuel cell. A study relative to domestic energy consumption dealt with transition in the energy consumption rate, dependence on locality, and the effect of the makeup of residences. The monthly and hourly patterns of demand for heat for hot-water supply were referred to power consumption data broken down by time zone, and it was found that approximately 1kW output would be suitable for this purpose. A study was made about the pattern of operation that such a fuel cell system should follow, and it was learned that a pattern in which 'the system operates according to the imposed load starting at seven o'clock in the morning when the electricity rate switches to the higher and the output does not exceed what is necessary to meet the daily demand for heat.' This method was found to assure the most efficient way of operation covering more than 80% of the need for hot water and electricity. In a study of consumption of energy for business, feasibility was suggested to exist in the installation of systems of 30kW or less at small hotels, barber shops and beauty parlors, restaurants, schools equipped with minor-scale food service, small hospitals, clinics, and the like. (NEDO)

  10. Survey for making a data book related to the development of new energy technology. Fuel cell; 1999 nendo shin energy gijutsu kaihatsu kankei data shu sakusei chosa hokokusho. Nenryo denchi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    To proceed with the systematical arrangement of the new energy related data, this survey collected the data relating to fuel cells, and systematized them with the aim of making a data book related to fuel cells. Further, fuel cells are still developing, and therefore, the trend of development in this one year was roughly seen to make it the data toward the future development. This data book is composed of Part 1 (the world development trend in FY 1999) and Part 2 (data book). Part 1 was divided into the fixed power system (Chapter 1), fuel cell vehicle (Chapter 2), and selection of fuel (Chapter 3). The book has a big feature that the selection of fuel was added as an individual chapter, which is a difference from that of FY 1998. In the description of the developmental trend of fuel cell vehicle (FCV) in Chapter 2, the results of the present development and the trend were described in line with the subjects in achieving the commercialization of FCV. Part 2 is a data book which indicates the state of technology development of each of various fuel cells such as actual results of the demonstrative operation of fuel cells in Japan and abroad. (NEDO)

  11. FY 1994 Report on the results of the joint research project for optimum introduction of development of fuel cell technologies for urban energy centers; 1994 nendo toshi energy center nado nenryo denchi gijutsu kaihatsu saiteki donyu chosa seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-01

    Described herein are the FY 1994 results of the joint research project for optimum introduction of development of fuel cell technologies for urban energy centers or the like. The necessary economic conditions for introduction of a fuel cell system to be competitive with the conventional system which individually supplies electric power and heat are 250,000 yen/kW as the construction unit cost, 0.10m{sup 2}/kW as the installation area, 5 years as the cell body life, use of an inexpensive fuel gas (2 to 6 yen/Mcal). Moreover, it is an indoor system which shall have the operational characteristics to follow daily demand fluctuations while operating under the optimum conditions in the urban redevelopment area considered. A 5,000kW-class fuel cell plant burning fuel gas (2 yen/Mcal) will need a total floor area of approximately 400,000 m{sup 2} in an energy-intensive office type demand area. These conditions shall be met in order to economically introduce the 5,000kW-class plant. It is also necessary to compare the plant with the competitive cogeneration plants. The specifications for the prototype now under consideration are sufficient for the energy-saving effect, and it is premised that these specifications and characteristics are secured. (NEDO)

  12. Fuel cell heat utilization system; Nenryo denchi netsuriyo sochi

    Energy Technology Data Exchange (ETDEWEB)

    Urata, T. [Tokyo (Japan); Omura, T. [Tokyo (Japan)

    1995-07-04

    In the conventional fuel cell heat utilization system, the waste heat is recovered to be utilized by either the waste heat recovery heat exchanger or the waste heat recovery steam. In the employment of the waste heat recovery heat exchanger system, however, the utility value is decreased when the temperature of the waste heat is lowered. Contrarily, in the employment of the waste heat recovery steam system, the supplementary water requirement is increased corresponding to the amount of waste heat recovery steam, resulting in the cost increase for water treatment. This invention solves the problem. In the invented fuel cell heat utilization system, a pressurized water from the steam separator is introduced into the second circuit to utilize directly the heat in the heat utilization system without employing the heat exchanger. If a blowdown valve is installed between the second circuit heat utilization system and the steam separator, the heat loss due to the blowdown can be reduced, since the low temperature water is blown down after being utilized in the heat utilization system. 4 figs.

  13. Survey report on the status of new energy in the U.S. On-site research centering on fuel cell, hydrogen energy, and wind energy (4th World Energy Engineering Congress); Beikoku shin energy jijo chosa hokokusho. Nenryo denchi, suiso furyoku energy wo chushin to suru jicchi chosa (dai 4 kai World Energy Engineering Congress)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-02-01

    A survey group dispatched by the New Energy Industrial Forum technical development committee conduct researches into the status of technologies in the U.S. relative to fuel cells, hydrogen energy, and wind energy. The group also attend the 4th World Energy Engineering Congress. As for the research and development of the phosphoric acid fuel cell, it is undertaken by the United Technology Corporation, Westinghouse Electric Corporation, and the Engelhard Corporation, each having its own peculiar technologies and thereby avoiding competition with others in one and the same domain. As for the molten carbonate fuel cell, the Argonne National Laboratory is entrusted with the control of technology development, and the Laboratory in turn requests the United Technology Corporation and Westinghouse Electric Corporation to develop technologies and systems. As for the solid oxide fuel cell, the Westinghouse Electric Corporation is entrusted with its development through the intermediary of the Argonne National Laboratory. As for hydrogen energy, the General Electric Company and Westinghouse Electric Corporation develop hydrogen production systems and the Brookhaven National Laboratory develops hydrogen storage systems using metallic hydrides. As for wind power generation, a Bendix-made 3,000kW wind power plant is visited and discussion is held on it. (NEDO)

  14. Survey report on the status of new energy in the U.S. On-site research centering on fuel cell, hydrogen energy, and wind energy (Westinghouse Electric Corporation); Beikoku shin energy jijo chosa hokokusho. Nenryo denchi, suiso furyoku energy wo chushin to suru jicchi chosa (Westinghouse Electric Corporation hen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-02-01

    Under the auspices of the New Energy Foundation and the New Energy Industrial Forum technical development committee, a survey team is sent to the U.S. and conducts investigations there about fuel cells, hydrogen production, wind power generation, etc. Visited in the U.S. are the Advanced Energy System Division of the Westinghouse Electric Corporation. As for the phosphoric acid fuel cell, research and development is under way so that two 7.5MW demonstration plants will start service operation by 1987. As for the solid oxide fuel cell, a performance test has completed for a 15-cell model, and a life test is now under way. There is a plan to construct a 500kW plant in 1988. In the production of hydrogen by means of the sulfur hybrid decomposition process, a laboratory model with a capacity of 2L/min was built in 1978, and a life test is now under way for the constituent materials and catalysts. In the field of wind power, the Westinghouse Electric Corporation has developed a 200kW generator, which is now in operation in Mexico, Puerto Rico, Rhode Island, and Hawaii. (NEDO)

  15. Fiscal 1994 report on technological results. Development of fuel cell technology such as urban energy center (Survey for practical development of optical system of decentralized power source for residential use); 1994 nendo toshi energy center nado nenryo denchi gijutsu kaihatsu seika hokokusho. Minseiyo bunsangata dengen saiteki system jitsuyoka kaihatsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-01

    Feasibility study was conducted on the technology for practical application of a several kW class fuel cell for the people's livelihood, particularly, for residential use. The study was made in six areas consisting of study on the present state of technology, conceptual design of a small fuel cell, survey on a promising market, basic concept of cell for residential use, feasibility study on application and on introduction. There is no record of development of the several kW class; while the fuel cell excels in the efficiency of energy utilization and the environmental conservation, its performance greatly deteriorates by start and stop under the present technology. Accordingly, it is a prerequisite that the equipment is for an electric heat combined type and for system interconnection. Also, while it is proper that the cell is phosphate type and that the fuel is natural gas, an innovation is necessary in the technology for reforming the cell and the fuel. The conceptual design revealed the possibility of a power generation system having a generating efficiency of 32%, exhaust heat recovery rate of 30%, and dimension of 75x65x150 cm. On the basis of a feasibility study on the application to the combination of a house and a beauty parlor, an advantage was recognized in the fuel unit cost of 5 yen/meal and the equipment cost of 200-250 thousand yen/kW, with demand estimated for 2.5 million installations nationwide including 950 thousand in natural gas supply districts. (NEDO)

  16. Fiscal 1991 report. International Fuel Cell Conference; Nenryo denchi kokusai symposium hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    Lectures, presentations, and questions given at the event involved items 1) Plenary session, 2) Technology development strategies, 3) Phosphoric acid fuel cell (PAFC), 4) Molten carbonate fuel cell (MCFC), 5) Solid oxide fuel cell (SOFC), 6) Other fuel cells, and item 7) Closing session. Under item 1), current states and prospects of technological development were reported by Agency of Industrial Science and Technology of Japan and by industrial technology developing organizations of the U.S. and Europe. Under item 2), a report was given by the U.S. about a fuel cell-driven automobile developing program. Under item 3), a report was given on the exchange of information about plant operation, maintenance, and inspection with importance attached to accuracy. Under item 4), reports were given about a 70kW stack operating program of the U.S. and a 1MW stack pilot plant program of Japan. Under item 5), some NEDO (New Energy and Industrial Technology Development Organization) projects and a 25kW stack operating test of Westinghouse Electric Corporation were reported. What were learned through participation in this conference are mentioned below. Japan is in the forefront as far as the development of PAFC and MCFC technologies are concerned. The U.S. is ahead of Japan in the development of SOFC while also in Japan efforts to develop element technologies for SOFC are in progress steadily. The U.S. and European countries lead Japan in the development of the polymer electrolyte fuel cell (PEFC). (NEDO)

  17. Water supply method to the fuel cell cooling water system; Nenryo denchi reikyakusuikei eno kyusui hoho

    Energy Technology Data Exchange (ETDEWEB)

    Urata, T. [Tokyo (Japan); Nishida, S. [Tokyo (Japan)

    1996-12-17

    The conventional fuel cell has long cooling water piping ranging from the fuel cell exit to the steam separator; in addition, the supply water is cooler than the cooling water. When the amount of supply water increases, the temperature of the cooling water is lowered, and the pressure fluctuation in the steam separator becomes larger. This invention relates to the water supply method of opening the supply water valve and supplying water from the supply water system to the cooling water system in accordance with the signal of the level sensor of the steam separator, wherein opening and closing of the supply valve are repeated during water supply. According to the method the pressure drop in every water supply becomes negligibly small; therefore, the pressure fluctuation of the cooling water system can be made small. The interval of the supply water valve from opening to closing is preferably from 3 seconds to 2 minutes. The method is effective when equipment for recovering heat from the cooling water is installed in the downstream pipeline of the fuel cell. 2 figs.

  18. Development of MCFC and PEFC technologies; Jisedai nenryo denchi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Hori, M; Ozu, H; Sonai, A [Toshiba Corp. Tokyo (Japan)

    1996-06-01

    Next-generation fuel cells under development by Toshiba Corporation are outlined. The molten carbonate fuel cell (MCFC) has become stable in performance, which results from the conversion of the matrix group from the {gamma}-type to {alpha}-type LiAlO2. The cathode material is expected to withstand the elution of electrolyte for 20000 hours. The soft structure separator developed for stack constitution is expected to improve electrical contact and reduce the cost of stack. An appliance has been completed to tentatively produce every element concerned. During an actual operation, the structural soundness of the 2-cell stack was confirmed by thermal load tests. As for the polymer electrolyte fuel cell (PEFC), an interior humidification method has been developed using a porous material for supplying water to the polymer film. The amount of moisture can be controlled, which will enable a larger-area cell. A 1kW-class stack with a world-record-level 1200cm{sup 2} electrode area has been developed, which stack has shown that the target output has been attained. Furthermore, the power generation efficiency of the system including fuel treatment has been examined. 10 figs.

  19. Manufacturing method of molten carbonate fuel cell. Yoyu tansan prime en nenryo denchi no seizo hoho

    Energy Technology Data Exchange (ETDEWEB)

    Muneuchi, Atsuo; Murata, Kenji

    1989-09-14

    An fuel electrode of a molten carbonate fuel cell is preliminarily dipped with molten carbonate. This operation is troublesome and reduces the productivity because this operation is made by the fuel electrode unit. In this invention, the carbonate is dipped in the process of temperature elevation after the assembly of the fuel cell. In other words, the carbonate electrode is buried in a groove formed in the fuel electrode leaving a gas flowing space; this fuel electrode is layer-built with a matrix and an oxidant electrode to form a unit cell; this unit cell is assembled to compose a fuel cell; while an anti-oxidant gas is fed to a groove of the fuel electrode, temperature is raised up to the operation level, wherein the carbonnate in the groove is molten to be dipped into the fuel electrode. The anti-oxidant gas is such inactive ones as carbon dioxide, nitrogen, argon and helium. 2 figs.

  20. Gas replacement system for fuel cell. Nenryo denchi no gas chikan hoshiki

    Energy Technology Data Exchange (ETDEWEB)

    Sugiyama, T

    1990-02-14

    When stopping the operation of a fuel cell, the gas in the reaction gas system is purged using such an inert gas as nitrogen for inactivation. A gas source such as inert gas bomb must be prepared beforehand for the purpose. This invention relates to a method of production of inert gas from the air collected from atmosphere to use it as the purge gas. The air collected from the atmosphere is passed through an oxygen remover filled with oxidation catalyst to remove oxygen, and dehumidified by a dehumidifier filled with drying agent, the obtained inert drying gas with nitrogen as the main constituent being used as the purge gas. Copper system catalyst supported by silica is used as the oxidation catalyst, and silica gel as the drying agent. After the operation of the fuel cell is re-started, a part of the high temperature fuel gas extracted from the reaction gas system is introduced to the oxygen remover for the reduction of oxidation catalyst and for heat regeneration of dehumidifying agent by the contained hydrogen. 1 fig.

  1. Molten carbonate fuel cell power generation system. Yoyu tansan prime en gata nenryo denchi hatsuden sochi

    Energy Technology Data Exchange (ETDEWEB)

    Uematsu, K; Hatori, S [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1991-11-01

    In an indirect internal reforming type molten carbonate fuel cell, the reforming temperature is limited less than the operating temperature of the fuel cell, as the heat source for reforming is depended on the reaction heat at about 650 {degree} C of the fuel cell. To improve the reforming rate at the low temperature range, it is considered to increase S/C (ratio of steam to carbon), but this scheme will cause such problems as to increase the voltage drop of the anode, to drop the heat recovery ratio on the cogenerator, to increase the capacity of the heat exchanger, etc. In this invention, in the power generating plant of a molten carbonate fuel cell the inert gas is added to the reforming raw gas, and in addition to the above the gas is mixed with steam and led into the reforming chamber of the plant. When the inert gas which is not directly concerned in the reforming reaction is added to, total mol number increases and the reforming reaction is acceralated. Consequently, the reforming rate can be raised, though the reforming temperature is low. 2 figs.

  2. FY 1999 Report on research and development of power generation by solid electrolyte fuel cell. Research and development of solid electrolyte fuel cell; 1999 nendo nenryo denchi hatsuden gijutsu kaihatsu kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu kenkyu seika

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-06-01

    This project is aimed at establishment of the module basic technology and commercialization of the solid electrolyte fuel cell in the early stage by designing, construction, operation and performance evaluation of a several kW-class module which incorporates the cylindrical cell fabricated by the wet process. The FY 1999 R and D efforts include (1) cell performance demonstration study: the cylindrical single cell fabricated by the wet process is demonstration-tested to determine the initial performance and durability for continuous operation, thereby comparing the external reforming with internal reforming in output, with the internal reforming rate as the parameter, (2) development of a several kW-class module: the adequate cell arrangement structure within the module is studied by the computer-aided simulation, and the tests for confirming thermal cycle durability of the modified bundle are conducted using the module power generation unit and the several kW-class module is tested, and (3) development of the technology for designing a thermally supported module: the effects of, e.g., air and fuel supply conditions on the module performance are analyzed using the analytical model as the base. Expansion of the module level to the process simulation model has been completed, based on these results. (NEDO)

  3. Achievement report on research and development in the Sunshine Project in fiscal 1979. Research on fuel cells (Research on aqueous alkaline solution electrolyte fuel cells); 1979 nendo nenryo denchi no kenkyu seika hokokusho. Arukari suiyoeki denkaishitsu nenryo denchi no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-03-01

    This paper describes achievements in fiscal 1979 in research on aqueous alkaline solution electrolyte fuel cells. Trial fabrication and tests for an oxygen electrode were performed on a catalytic electrode added with silver using carbonblack and graphites as carriers having excellent corrosion resistance and large surface area. Characteristics not inferior to electrodes using activated carbon as a carrier were obtained in both of the initial characteristics and continuous discharge characteristics. A platinum added electrode also showed the same performance as the silver added electrode. A hydrogen electrode containing Zr and iron among those containing Raney-Ni was found to have high oxidation resistance and stability in terms of life. A platinum added electrode using graphite as a carrier provided satisfactory initial characteristics as a hydrogen electrode. Research on a single cell construction has used and tested eight-cell laminated cells with an area of 1,000 cm{sup 2} using bipolar sheets made of carbon. The test verified appropriate the removal of produced water and heat using mainly the hydrogen circulation, which has been discussed in the summary design. The paper describes heat cycles, for which tests of ten and odds times in total were performed to have demonstrated that they are free of any anomaly. Furthermore, a manifold was attached as a means to improve the volume efficiency. Its function was also tested. (NEDO)

  4. FY 1993 report on the results of the commissioned research and development project. R and D of SOFC (solid oxide fuel cells); 1983 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. SOFC kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-05-01

    The research and development project is carried out for fuel cell power generation technologies and solid electrolyte type fuel cells, and the reports on the FY 1993 results issued by the participant organizations are summarized. For R and D of the modules, Fuji Electric conducted the R and D for the large-area, cell-stacked type, and Sanyo Electric for the composite cell-stacked type. For R and D of the materials and fundamental technologies, Fine Ceramics Center conducted the R and D for microscopic structures of the electrode, Fujikura for electrode structures produced by spraying or the like, Mitsubishi Heavy Industries for multi-functional fuel electrodes, Murata Seisakusho for co-sintering technologies, and Mitsui Shipbuilding for current collecting technologies. For R and D of the systems, Central Research Institute of Electric Power Industry conducted the R and D for the systems, Electric Power Development and Mitsubishi Heavy Industries jointly for designs of the cell peripheries, and the Japan Research and Development Center for Metals for elementary technologies for the peripheral devices. (NEDO)

  5. FY 1992 report on the results of the commissioned research and development project. R and D of SOFC (solid oxide fuel cells); 1992 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. SOFC kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-05-01

    The research and development project is carried out for fuel cell power generation technologies and solid electrolyte type fuel cells, and the reports on the FY 1992 results issued by the participant organizations are summarized. For R and D of the modules, Fuji Electric conducted the R and D for the large-area, cell-stacked type, and Sanyo Electric for the composite cell-stacked type. For R and D of the materials and fundamental technologies, Fine Ceramics Center is conducted the R and D for microscopic structures of the electrode, Fujikura for electrode structures produced by spraying or the like, Mitsubishi Heavy Industries for multi-functional fuel electrodes, Murata Seisakusho for co-sintering technologies, and Mitsui Shipbuilding for current collecting technologies. For R and D of the systems, Central Research Institute of Electric Power Industry conducted the R and D for the systems, Electric Power Development and Mitsubishi Heavy Industries jointly for designs of the cell peripheries, and the Japan Research and Development Center for Metals for elementary technologies for the peripheral devices. (NEDO)

  6. FY 2000 report on development of the infrastructure to promote use of fuel cells for automobiles. Standardization of FCEVs; 2000 nendo nenryo denchi fukyu kiban seibi jigyo jidoshayo nenryo denchi fukyu kiban seibi seika hokokusho. FCEV hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the results of the FY 2000 activities for standardization of fuel cell powered vehicles and development of the infrastructures related to participation in ISO. Fuel cell powdered vehicles are believed to be the most favored vehicles of the next generation for their low emissions and fuel efficiency. The world leading automakers, including Japanese makers, have announced plans to commercialize these vehicles in 2003 to 2004. Under these situations, the discussion has been initiated to move forward standardization of the fuel cell powdered vehicles at the international conferences, e.g., ISO (International Standardization Organization) and IEC (International Electrotechnical Commission). At ISO/TC22/SC21 (Electric Vehicles) for which the Japan Electric Vehicle Association (JEVA) is in charge as the domestic council, the proposal has been made and approved to begin working towards the standardization at the conference in November 1999. Consequently, FCEV special subcommittee consisting of public organizations (including academic organizations and Ministry of Economy, Trade and Industry), automakers, automotive parts manufacturers and other organizations related to the automotive industry has been established in February 2000 under the JEVA standardization section and started the activities. The Japanese proposals for safety and fuel cell vehicle terminology will be presented to the ISO meetings to be held in May 2001 in Tokyo. (NEDO)

  7. Achievement report on research and development in the Sunshine Project in fiscal 1980. Research on fuel cells (Research on aqueous alkaline solution electrolyte fuel cells); 1980 nendo nenryo denchi no kenkyu seika hokokusho. Arukari suiyoeki denkaishitsu nenryo denchi no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This paper describes the achievements in fiscal 1980 in the Sunshine Project on developing aqueous alkaline solution electrolyte fuel cells. The oxygen electrode is a silver catalyst electrode using as carriers carbon lack and graphite powders having good corrosion resistance. A continuous discharge test was performed on the electrode for 3,000 hours. Furnace black having large surface area and naturally colloidal graphite showed stable performance. The hydrogen electrode, which is a catalyst electrode made of Raney-Ni containing third elements was given a 3000-hour continuous discharge test, where Zr addition presented stable performance. Activated carbon was found a good carrier in platinum added electrodes. For electrodes operating under high pressure gases, electrodes attached with sintered nickel film are suitable. With regard to prototype cells, laminated cells with high volume efficiency structured mainly with gasket seals were designed and fabricated. The IV characteristics measurement and continuous discharge test thereon revealed no functional problems. Furthermore, cells having electrode area of 100 cm{sup 2} and using bipolar sheets made of carbon were verified capable of withstanding 2000-hour continuous discharge. A non-conductive resin mold was proposed to prevent electrolytic corrosion of the carbon sheets. Discussions were given also on corrosion resistance of bonding agents. (NEDO)

  8. FY 1998 annual report on the development of fuel cell power generation techniques. Research and development of solid electrolyte fuel cells (research results); 1998 nendo nenryo denchi gijutsu kaihatsu. Kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Described herein are the FY 1998 research and development results of solid electrolyte fuel cells. For R and D of the tubular type cell by the wet processing technique, the tests are conducted to evaluate the initial performance and long-term durability for continuous operation of the single tubular cell. For development of the several-kW class modules, computer-aided simulations are conducted. For R and D of material and substrate techniques, the thermal cycle characteristics, cell characteristics and stress of the cell modules are evaluated, in order to evaluate their reliability. The thermal cycle test results indicate that performance of the single-stage cell is unaffected by the thermal cycles. It is found by the stress evaluation that use of the separator plate having a higher thermal expansion coefficient than the electrolyte plate and use of the sealant having a thermal expansion coefficient close to that of the electrolyte plate are effective means to reduce stresses. For the research to reduce costs of the cell materials, their chemical, mechanical and thermal characteristics are evaluated. For the system research, the areas for which the compact systems are suitable and their optimization are studied. (NEDO)

  9. Fiscal 1993 international research cooperation project. Feasibility study of finding out the seeds of international joint research (technology for environmental preservation using biotechnology, technology for effective use unused hydrocarbon resource, technology of solid electrolyte fuel cells for high-efficient electric vehicles); 1993 nendo kokusai kenkyu kyoryoku jigyo. Kokusai kyodo kenkyu seeds hakkutsu no tame no FS chosa (biotechnology ni yoru kankyo taisaku gijutsu, miriyo tanka suiso shigen no yuko riyo gijutsu, kokoritsu denki jidosha no kotai denkaishitsu nenryo denchi gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    This project is aimed at internationally cooperating in the R and D of industrial technology and improving industrial technology of Japan. For it, the following three technologies were investigated: 1) environmental preservation technology using biotechnology, 2) technology for effective use of unused hydrocarbon resource, 3) solid electrolyte fuel cell (SOFC) technology for high-efficient electric vehicles. In 1), bio-remediation is a choice as the result of trially using technologies for remediation of the environment polluted by pollutant, but it is not a technically completed one, but one which will be improved by trial and error. By the application of gene engineering, the use of gene recombination enables wide spread of decomposition genes. In 2), technical subjects were studied such as superheavy distillate, oil shale, coalhead methane and methane hydrate. In 3), designed were cylinder type and planar type SOFC of 850degC operation and 10kW output. Accumulation and weight of a total SOFC system are 81 liters and 100 kg in cylinder type and 136 liters and 200 kg in planar type. The vehicle can be equipped with the SOFC. 171 refs., 72 figs., 54 tabs.

  10. Study on fuel supplying method and methanol concentration sensor for the high efficient operation of methanol fuel cells. Methanol nenryo denchi no unten ni okeru nenryo kyokyu hoho no kento to methanol nodo sensor no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tsukui, Tsutomu; Doi, Ryota; Yasukawa, Saburo; Kuroda, Osamu [Hirachi, Ltd., Tokyo, (Japan)

    1990-01-20

    A fuel supplying method was studied and demonstrated, essential to the high efficient operation of methanol fuel cells. Methanol and water were supplied independently from each tank to an anordic electrolyte tank in a circulating system, detecting a methanol concentration and liquid level of anordic electrolyte by each sensor, respectively. A methanol sensor was also developed to detect accurately the concentration based on electrochemical reaction under a constant voltage. A detection control circuit was insulated from a constant-voltage power supply to prevent external noises. The methanol sensor output was compensated for temperature, and a new level sensing method was adopted to send out a command comparing different responses to electrolyte shortage. As the methanol fuel cell was operated with this fuel supplying system, the stable characteristics of the cell were obtained within the variation of {plus minus} 0.1mol/l from the specified methanol concentration. 6 refs., 17 figs., 1 tab.

  11. Survey report for fiscal 1998. Achievement report on research and development of direct methanol fuel cell; 1998 nendo direct methanol nenryo denchi no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-12-01

    Research and development has been performed on a direct methanol fuel cell (DMFC) to generate electric power through direct chemical reaction of methanol not being given modification as a fuel cell to be used for automotive engines. This paper summarizes the achievements in fiscal 1998. In the research of the membranes to conduct ions for the DMFC, an ion conduction membrane which introduces POSS group as the methanol eliminating functional group was prepared to achieve enhancement in tensile strength, heat resistance, and ion conductivity. In the power generation characteristics of the DMFC, verification was given on power generation performance with as high main power density as 0.1 W/cm{sup 2} by using the available electrolytic membranes and electrode catalysts. The characteristics showed effectiveness of the DMFC as the electric power supply source. In addition, fundamental findings were obtained on factors affecting the power generation characteristics of the DMFC as a result of generating power under different conditions. Research and development was given also on the water-methanol-ion exchange polymeric membrane, ion exchange membranes provided with lipophilic and water repellent electrolyte, solid polymeric membranes having high proton conductivity and low methanol permeability, and a new micro-porous filling type polymeric membrane. (NEDO)

  12. FY 2000 report on the results of the R and D of solid oxide fuel cells (SOFC); 2000 nendo kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    Development of fuel cell power generation technology and R and D of solid oxide fuel cells were carried out, and reports of the FY 2000 results of companies were summed up. As to the R and D of the cell module, the R and D on the wet type cylinder module were made jointly by Toto Ltd., Kyushu Electric Power Co. and Nippon Steel Corp. As to the R and D of materials/basic technology, the following were conducted: evaluation of reliability of the cell module (evaluation of thermal cycle characteristics, etc.) by Chubu Electric Power Co., evaluation of reliability of the cell module (cell characteristics/stress evaluation) by Tokyo Gas Co. Ltd., cost reduction of cell materials (evaluation of chemical characteristics) by Central Research Institute of Electric Power Industry, and cost reduction of cell materials (evaluation of mechanical/thermal characteristics) by Japan Fine Ceramics Center. Concerning the system study, study of the system (adaptation fields of the small system and the optimization) was conducted by Nippon Steel Corp. (NEDO)

  13. Achievement report for fiscal 1997 on research and development of solid electrolyte fuel cells; Kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu 1997 nendo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-07-01

    This paper describes the achievements in fiscal 1997 on research and development of solid electrolyte fuel cells. Fuji Electric has demonstrated possibilities of film type cells of predominantly metallic flat plate supporting type of a large-area cell lamination system, and seal-less stack structure. Sanyo Electric has discussed making thinner the composite cell lamination type anode, optimization in sintering temperature, and sealing materials. The Fine Ceramic Center has performed a 1,000-hour test on an La(Sr) MnO{sub 3}-YSZ electrode, in which A-site defect amount was decreased to 0.1-0.02 to stabilize micro-structure air electrodes for an extended period of time. Fujikura has discussed functional materials for high dispersion and slanting in a fuel electrode Ni/YSZ. Mitsubishi Heavy Industries has fabricated MgO-based fuel electrodes on a trial basis, and performed internal reformation and power generation tests by using full-size stacks. Murata Manufacturing Company has verified long-term power generation properties and stability of a three-layered co-sintered film of flat plate type. Mitsui Shipbuilding has reached a near final conclusion on the basic structure of gas separator cells. The Central Electric Power Research Institute has completed a conceptual design on a 300-MW class composite power generation system in which SOFC and gas turbines are combined. The Electric Power Development Company has discussed problems in SOFC composite power generation development using coal gasified fuel. (NEDO)

  14. Electrolyte loss mechanism of molten carbonate fuel cells. 1; Yoyu tansan`engata nenryo denchi ni okeru denkaishitsu loss kiko ni tsuite. 1

    Energy Technology Data Exchange (ETDEWEB)

    Sonai, A; Murata, K [Toshiba Research and Development Center, Kawasaki (Japan)

    1993-11-01

    During a single-cell disassembly test of molten carbonate fuel cells having been operated for 90 hours to 5500 hours, correlativity was discovered between decrease in the retained amount of electrolyte due to decrease in pore capacity of electrodes and electrolyte plates and the electrolyte loss. The electrolyte loss amount cannot be explained with the conventional mechanisms, thereby a new model was proposed. The cathode has shown very little change in the capacity change in pores with diameters smaller than 2 {mu}m per unit area. The anode has remained almost constant after 1000 hours, but the electrolyte plates have shown remarkable decrease. Therefore, it is possible to estimate that the electrolyte plates should have been the major cause for the electrolyte loss. The result of measuring the electrolyte loss amount agreed well with that estimated using pore capacity curves. This fact suggests that the electrolyte loss can be explained by a new mechanism that hypothesizes the existence of a largest size of retaining pores that can support carbonates and defines that the electrolyte loss is generated from decrease in the pore capacity. 7 refs., 8 figs., 1 tab.

  15. Sintering behavior of porous electrolyte supporting matrix for molten carbonate fuel cells; Yoyu tansan`en nenryo denchi denkaishitsu hojiso no shoketsu kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Sonai, A; Murata, K [Toshiba Research and Development Center, Kawasaki (Japan)

    1993-11-01

    Considerations were given on pore distribution in lithium aluminate that supports electrolyte in molten carbonate fuel cells under cell operating condition, and its sintering mechanism by measuring time-based change in the linear contraction. The following findings were obtained: Pore capacity in the lithium aluminate layer has decreased in 1000-hour operation, creating pores with diameters greater than 2 {mu}m in which no carbonates have been filled; the cross-leak in reaction gases and ion resistance in the electrolyte retaining layer have increased resulting in degraded cell performance; the lithium aluminate layer has generated initial quick densification as a result of melting of the carbonates, with the more the liquid phase, the larger the linear contraction; and pores with diameters greater than 2 {mu}m are thought to have been generated as the densification of the lithium aluminate due to dissolution and reprecipitation progresses. The densification can be explained well if this is regarded to consist of a slow densification process in association with sintering of lithium aluminate particles, and progress in a sintering mechanism where solid phase has solubility against liquid phase. 9 refs., 8 figs.

  16. Fundamental analysis of thermally regenerative fuel cell utilizing solar heat; Taiyonetsu wo riyosuru netsu saiseigata nenryo denchi no kiso tokusei no kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Ando, Y; Tanaka, T; Takashima, T; Doi, T [Electrotechnical Laboratory, Tsukuba (Japan); Aosawa, T; Kogoshi, S [Science University of Tokyo, Tokyo (Japan)

    1997-11-25

    Study was made on a thermally regenerative fuel cell using solar heat. The thermally regenerative fuel cell was devised which is composed of 2-propanol liquid-phase endothermic dehydrogenation at nearly 100degC, and acetone liquid- phase exothermic hydrogenation at nearly 30degC as reverse reaction. This low-temperature dehydrogenation can relatively easily utilize a flat solar heat concentrator. 2-propanol dehydrogenation generates acetone and hydrogen. Generated acetone generates electric power in hydrogenation, generating propanol. This propanol regenerates acetone and hydrogen in dehydrogenation. The activity of Ru and Pt composite catalyst was considerably higher than that of Ru or Pt single catalyst. The activity was also higher in carbon felt or carbon cloth carrier than carbon plate carrier. The open circuit voltage of the fuel cell was estimated to be 110-120mV, nearly consisting with theoretical values. Short circuit current was also estimated to be 9-11mA, suggesting reduction of its internal resistance as an important subject. 4 refs., 5 figs., 2 tabs.

  17. Heat recovery properties from fuel cell system for telecommunications use; Tsushin`yo nenryo denchi system ni okeru hainetsu kaishu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Ishizawa, M.; Iida, S.; Abe, I.; Yamamoto, M. [NTT Integrated Information and Energy Systems Laboratories, Tokyo (Japan)

    1997-08-20

    NTT is developing a phosphoric-acid fuel-cell energy system for telecommunication co-generation systems to reduce energy costs and help preserve the environment. Fuel cells are used to provide electrical power to telecommunication equipment and the heat energy that is generated is used by the absorption refrigerators to cool the telecommunication rooms throughout the year. We field-tested this fuel-cell energy system in a telephone office. Two heat recovery methods were applied in the test: one uses direct steam heat recovery from fuel-cell stack coolant to keep the heat recovery temperature high and to avoid requiring a heat exchanger for the recovery; the other uses heat recovery from the reformer exhaust gas that is directly in contact with the heat recovery water to recover heat more economically. Our field tests confirmed that the average efficiency of heat recovery from fuel-cell stack coolant is 16%, and from the reformer exhaust gas is 9% under 80-kW continuous operation. Maximum total efficiency including electrical power efficiency was confirmed to be about 73% under the condition of 100-kW and an S/C ratio of 2.5 in the winter period: heat recovery from the fuel-cell stack coolant was 23%, from the reformer exhaust gas was 10%, and from electrical conversion was about 40%. 9 refs., 12 figs., 1 tab.

  18. Hear recovery properties from fuel cell system for telecommunications use; Tsushin`yo nenryo denchi system no fuirudotesuto ni okeru hainetsu kaishu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Ishizawa, M.; Iida, S.; Abe, I.; Amanuma, H. [NTT Integrated Information and Energy Systems Laboratories Tokyo (Japan); Uekusa, T.; Waragai, S. [NTT Power and Building Eacilities Inc., Tokyo (Japan)

    1997-12-20

    NTT is developing a phosphoric acid fuel cell energy system for telecommunication co-generation systems to reduce energy costs and help preserve the environment. Fuel cells are used to provide electrical power to telecommunication equipment and the heat energy that is generated is used by the absorption refrigerator to cool the telecommunication rooms throughout the year. We fieldtested this fuel cell energy system in a telephone office for three years. Heat recovered water from fuel cell stack coolant was supplied to the absorption refrigerator and further extra-heat was recovered by a heat exchanger. The toral heat recovery amount was about 86000 kca/h (the heat recovery efficiency was 20%) under 200kW operation. The absorption refrigerator was supplied about 49000kcal/h of heat and operated with 0.7 of coefficient of performance throughtout the year. The electrical efficiency was maintained more than 38% after 13000h operation. 12 refs., 10 figs., 3 tabs.

  19. Collection of summaries of polymer electrolyte fuel cell research and development reports presented at fiscal 2000 meeting; 2000 nendo kotai kobunshigata nenryo denchi kenkyu kaihatsu seika hokokukai yoshishu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-08

    Contained in this book are the summaries of 26 essays presented at an achievement reporting conference on polymer electrolyte fuel cell (PEFC) research and development held in Tokyo on March 8, 2000. In the development of high-efficiency energy systems for transportation and residential/commercial sectors, 6 essays are summarized, involving ion exchange membranes, normal pressure operation type several kW class power source systems for home use, and so forth. For the practical application of high-efficiency fuel cell systems, 12 essays are summarized, involving technologies of PEFC low cost electrodes, PEFC module manufacturing, hydrogen separation type reforming, PEFC system manufacturing, and so forth. In relation to the establishment of technologies for a fuel cell popularization infrastructure and development of key technologies for high-efficiency fuel cells, 2 essays are summarized, involving the construction of a popularization infrastructure and development of evaluation test equipment, and the like, for automotive fuel cells. In relation to the development of key technologies and verification thereof for the practical application of fuel cells, 6 essays are summarized, covering the research and development of hydrogen producing liquid fuels and hydrogen absorbing alloys. (NEDO)

  20. Electrolyte loss mechanism of molten carbonate fuel cells. 2.; Application to the cell with matrix electrolyte layer; Yoyu tansan`engata nenryo denchi ni okeru denkaishitsu loss kiko ni tsuite. 2.; Matrix gata denkaishitsuso wo yusuru denchi eno oyo

    Energy Technology Data Exchange (ETDEWEB)

    Sonai, A; Murata, K [Toshiba Research and Development Center, Kawasaki (Japan)

    1993-11-01

    A single cell of molten carbonate fuel cell using a matrix electrolyte layer fabricated by using the doctor blade process has been operated for several thousand hours, measured of electrolyte loss amount, and analyzed by using a new electrolyte loss mechanism. The result may be summarized as follows: according to a result of measuring the matrix layer pore distribution, the average pore size has increased little by little; pores with diameters greater than 2 {mu}m at which no electrolyte retention becomes possible remain at nearly constant ratio up to 1800 hours, but increased after 2500 hours; the pore capacity in ports with the largest electrolyte retaining diameter of 2 {mu}m or less showed slight decrease with time in the anode, and an initial decrease followed by flatness, and then a sharp decrease after 1800 hours in the matrix layer; the electrolyte loss measurement values have remained nearly constant for 25 hours to 1800 hours, but increased sharply thereafter; and the electrolyte loss in this single cell due to pore capacity decrease in pores as power generating parts with diameters smaller than 2 {mu}m was explained quantitatively by a new electrolyte loss mechanism. 11 refs., 6 figs.

  1. Achievement report for 1st phase (fiscal 1974-80) Sunshine Program research and development - Hydrogen energy. Research on fuel cell (Research on high-temperature solid electrolyte fuel cell); 1974-1980 nendo suiso energy seika hokokusho. Nenryo denchi no kenkyu (koon kotai denkaishitsu nenryo denchi no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    Relative to the research and development of technologies for fabricating, and assessing, materials for the constitution of high-temperature solid electrolyte fuel cells, stabilized zirconia solid electrolyte fuel cell manufacturing technologies are developed by use of thin film formation techniques such as high-frequency sputtering, plasma CVD (chemical vapor deposition), and the thermolysis of organic zirconia compound coating. As the result, it is found that high-frequency sputtering produces thin film which is satisfying in terms of cost efficiency. Furthermore, it is found that defects in solid electrolytic thin film formed by the high-frequency sputtering method, that is, pinholes and cracks, will be remedied when the coating thermolysis method is jointly applied. In the research on fuel cell power systems, column-type high-temperature solid electrolyte fuel cells are built, and a power generation test is conducted. The test is successfully completed when the output of a fuel cell of the 9-column module structure gradually increases until a maximum output of 110W is achieved. (NEDO)

  2. Report on achievement in developing fuel cell power generation technology in fiscal 1998. Research and development of molten carbonate fuel cell power generation system (Test of the research result report); 1998 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. Yoyu tansan'engata nenryo denchi hatsuden system no kenkyu kaihatsu (kenkyu seika no honbun)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    This paper summarizes the text of the research result report in the separate volume II-1 from among the fiscal 1998 report on the achievement made on researching and developing a molten carbonate fuel cell (MCFC) power generation system. For the AC-DC type system whose high performance and large capacity stacks are being developed, detail designs were made on 250-kW class stack module assembly and installation procedure. At the same time, processing and forming were continued on such main components as electrodes, electrolyte plates and separators. The cells were assembled as modules, sintered, installed and adjusted. Aids were given by the process and control (PAC) test on devices and piping of the fuel cell system block. Cell life extension is also under study. For the parallel flow type stack, two 250-kW stacks were fabricated, and an overall adjustment test was begun thereon in March. For the reformer, an internal reforming system was developed for the 200-kW class system, whose adjustment test is scheduled for April 1999. Capacity increase is also under discussion. For practical use of MCFC, stack life of 40,000 hours is said required. The current status is at the level of exceeding 10,000 hours, but the necessity is seen in suppressing voltage drop associated with lapse of time. (NEDO)

  3. Achievement report for fiscal 1997 on joint research to develop fuel cell technologies for urban energy centers. Research on evaluating life of phosphoric acid fuel cells; 1997 nendo toshi energy center nado nenryo denchi gijutsu kaihatsu kyodo kenkyu seika hokokusho. Rinsangata nenryo denchi jumyo hyoka kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    This paper discusses life evaluation on phosphoric acid fuel cells of urban energy center type for regional energy supply and on-site type to be installed in buildings. Operation characteristics tests and disassembly checks allow to identify factors for voltage decrease, and estimate the life therefrom particularly if the voltage decrease is caused from catalyst activity. The time before 10% decrease value is reached is now about 40,000 hours. The creep analysis method that has been developed recently can predict deformation in full-size reformers nearly exactly, and is effective in operating the reformer and evaluating the life at the design stage. Creep buckling is the critical value, which is caused by ecliptic deformation of internal tubes in the second catalyst layer. In a heat exchanger for fuel gas preheating, carbon in the reformed gas is carbonized and deposited due to catalytic action of nickel in the brazing material that bonds plates and fins in the heat exchanger. Iron also has a possibility of performing catalytic action. In the on-site type 1,000-kW class fuel cells, no structural problems have been presented even after the operation has been stopped. In order to extend time interval between phosphoric acid supply into the cells, it is necessary to reduce difference in the remaining phosphoric acid amounts in the stack lamination direction and in the cell flat surface. (NEDO)

  4. FY 1999 Report on the technical results. Part 2-1. Development of fuel cell power generation technologies (Research and development of molten carbonate fuel cell power generation system); 1999 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. 2-1. Yoyu tansan'engata nenryo denchi (hatsuden system no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    This research and development project is aimed at modification and improvement of the stacking technologies, to improve service life and performance of the molten carbonate fuel cell power generation system and reduce its cost. For the cross-flow type stack, optimization of the anode firing conditions leads to controlled reduction of the fine pores, and incorporation of the cathode with MgO successfully leads to controlled elution of NiO and Ni short-cut. For the separator, the service life is extended by treatment of the material with Al and controlling its rigidity. The cell life prediction method is improved to enhance its accuracy. The cell life of -4.3mV/1,000h is achieved by these technologies. For the parallel-flow type stack, the electrodes are improved to achieve the cell life of -1.4mV/1,000h, the technologies for producing the separator for a 1m{sup 2} class unit are developed, and the basic structures of a large-capacity stack are designed. For the internal reforming type, a 200kW class reforming stack is constructed, and operated for 5,259 hours. The causes for electrolyte loss are analyzed by developing the relationships between operating temperature and electrolyte loss, electrolyte mass and sustainability of the cell characteristics, and steam partial pressure over the cathode and electrolyte loss, and also by testing the Ni short-cut. (NEDO)

  5. General report on the results of the development of fuel cell technology such as urban energy center. Evaluation study of life of phosphoric acid fuel cells (fiscal 1995 and 1996); Toshi energy center nado nenryo denchi gijutsu kaihatsu kenkyu seika sogo hokokusho. Rinsangata nenryo denchi jumyo hyoka kenkyu (1995 kara 1996 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Receiving subsidies from MITI, NEDO carried out this project in fiscal 1995 and 1996 as a joint research with Technology Research Association for Phosphoric Acid Fuel Cell Power Generation System and others. The project aimed at developing the accelerated test method which can evaluate in a short time the cell life of phosphoric acid fuel cells (PAFC) and the lowering of characteristics. The accelerated test method of PAFC life is thought to be a tool indispensable for the promotion of commercialization, but the accelerated test method like the usual material evaluation has not yet been established. To solve this problem, procedures were developed to rationally plan the accelerated test on short stacks of full scale based on the small cell test data. Here, to rationally estimate the operational state under actual conditions based on the data on the accelerated test, it is necessary to fully understand the mechanism of deterioration of PAFC. By conducting in parallel the element study for the basic elucidation of cell deterioration phenomena, obtained was the useful information/knowledge which back up the results of the accelerated test scientifically. 168 figs., 33 tabs.

  6. Fiscal 1997 development of fuel cell power generation technology. Part 3. Supplementary explanation to R and D of molten carbonate fuel cell and power generation system; 1997 nendo nenryo denchi hatsuden gijutsu kaihatsu hosoku setsumeisho. 3. Yoyu tansan'engata nenryo denchi (hatsuden system no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-05-01

    A supplementary explanation was compiled for the results of a commissioned project reported in fiscal 1997 (development of fuel cell power generation technology, and R and D (3) of molten carbonate fuel cell and power generation system). The supplementary explanation was given on the development of parallel flow stack, design/manufacturing of 250 kW stacks, design and manufacturing of 250 kW stacks in connection with installation/adjustment. (NEDO)

  7. Achievement report for fiscal 1998 on development of power generation using fuel cells. Research and development of molten carbonate fuel cell (II-2, text of the achievement); 1998 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. Yoyu tansan'engata nenryo denchi hatsuden system no kenkyu kaihatsu (II-2, kenkyu seika no honbun)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    The effort aims at developing a 1000kW-class power plant and also at using gasified coal as fuel in the future. The fuel system facilities include a high-temperature blower. The exhaust heat recovery facilities comprise a heat recovery steam generator (HRSG) and a turbine compressor. As for the electrical system facilities, an inverter is installed, tested, and adjusted. Control system facilities are also tested and adjusted. In relation with the operation of the plant, coordination is conducted about technological and process-related matters with the Kawagoe thermal power station of Chubu Electric Power Co., Inc., where the fuel cell power plant is to be constructed, which is for the smooth execution of a test run. Ceramic-based cathode materials are being developed, which is for the fabrication of stacks improved in performance, higher in current density, longer in life, and lower in cost. Also exerted are efforts at developing multiple-function electrolyte plates and metallic materials (for example for separator plating). The extent of the acceptability of impurities concentration and gas refining systems are also under study, which is to prepare for future coal gasification. Reference is also made to the study of a total system. (NEDO)

  8. FY 2000 report on the results of the infrastructure construction project for spreading high-efficiency fuel cell systems/development of test apparatuses for evaluation of fuel cell systems for automobiles; 2000 nendo kokoritsu nenryo denchi system kiban gijutsu kaihatsu / jidoshayo nenryo denchi system hyoka shiken sochi no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This project studies the testing/evaluation methods for spreading fuel cells for automobiles. Described herein are the FY 2000 results. The problems involved in evaluation of the single cell units are classified into those involved in the cell construction and methods of evaluating the operation performances of the single cell units. These problems are analyzed mainly by literature survey. The mode simulation tests will be greatly simplified, if the system can be tested on the bench without being actually boarded on the vehicle. Therefore, this project is aimed at development of a comprehensive mode simulator which can be automatically operated corresponding to the running modes of various countries, to test the performance of FCEV and to examine the effects of each component independently on the vehicle performance. The factors required to reproduce the actual driving states of an FCEV on the bench are analyzed, and the conceptual designs are drawn for the controlling algorithms. It is necessary to standardize the stack and reformer testing methods, in order to evaluate the fuel cell system components. For these objects, the prototype units are constructed to evaluate 10kW direct hydrogen type stacks and 5kW methanol reformers. The units are also constructed to evaluate the high-pressure (1MPa) reformer reactors and hydrogen separation membrane systems. (NEDO)

  9. Report on achievement in developing fuel cell power generation technology in fiscal 1998. Research and development of molten carbonate fuel cell power generation system (Summary of the research result); 1998 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. Yoyu tansan'engata nenryo denchi hatsuden system no kenkyu kaihatsu (kenkyu seika no yoyaku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Based on the achievement made in the second term plan of researching and developing a molten carbonate fuel cell power generation system, attempts are made on extending the service life, improving the performance, and reducing the cost. At the same time, lamination, cooling and operation technologies will be established, and a 1000-kW class power generation plant will be developed. Realization of use of coal gasified fuel in the future is aimed. Stack materials and their processing technologies will be developed, the cell durability will be improved, and the total system research will be carried out. This paper describes the achievements made during fiscal 1998. A process and control (PAC) test was performed on the fuel system facilities in the 1000-kW class generation plant, and its result was analyzed. The fuel system facilities had the test program using simulated fuel cells set from the system side digested nearly completely, verifying that actions can be taken for operation using actual fuel cells to be executed in fiscal 1999. Analysis of the test result presented raw material conversion rate of 96.6% or higher, generation of hydrogen plus CO of 740 m{sup 3} N/h, and NOx generation of 10 ppm or less. Stable combustion of a low calorie gas (500 kcal/m{sup 3} N) was achieved, completing all of the research objectives planned for fiscal 1998. (NEDO)

  10. FY 2000 report on development of the infrastructure to promote use of fuel cells for automobiles. Development of the infrastructure to spread stationary polymer electrolyte fuel cell (PEFC) systems; 2000 nendo nenryo denchi fukyu kiban seibi seika hokokusho. Teichiyo kotai kobunshigata nenryo denchi no fukyu kiban seibi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the results of the FY 2000 studies on development of the infrastructures necessary for introduction and spread of stationary polymer electrolyte fuel cell (PEFC) systems. This project is aimed at establishment of testing and evaluation methods for safety, reliability, performance and so on, and collection of the data, both domestic and foreign, for drafting rules and standardization. The methods are studied to collect the data for the start-up/shut-down operations and rated-load/partial-load operations; establishing the methods for safety evaluation when inert gas purging is dispensed with; and dependence of the cell stack on current, carbon monoxide concentration and cell temperature to establish the basic performance testing methods. The makers are independently developing the stationary PEFC systems, and the data of the selected systems are collected individually as the test systems. The cell stacks also adopt different humidification and cooling methods by makers, and they are tested and their data are collected and analyzed, in order to establish the common testing methods. (NEDO)

  11. Achievement report for fiscal 1998 on development of power generation using fuel cells. Research and development of molten carbonate fuel cell (II-2, text of the achievement); 1998 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. Yoyu tansan'engata nenryo denchi hatsuden system no kenkyu kaihatsu (II-2, kenkyu seika no honbun)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    The effort aims at developing a 1000kW-class power plant and also at using gasified coal as fuel in the future. The fuel system facilities include a high-temperature blower. The exhaust heat recovery facilities comprise a heat recovery steam generator (HRSG) and a turbine compressor. As for the electrical system facilities, an inverter is installed, tested, and adjusted. Control system facilities are also tested and adjusted. In relation with the operation of the plant, coordination is conducted about technological and process-related matters with the Kawagoe thermal power station of Chubu Electric Power Co., Inc., where the fuel cell power plant is to be constructed, which is for the smooth execution of a test run. Ceramic-based cathode materials are being developed, which is for the fabrication of stacks improved in performance, higher in current density, longer in life, and lower in cost. Also exerted are efforts at developing multiple-function electrolyte plates and metallic materials (for example for separator plating). The extent of the acceptability of impurities concentration and gas refining systems are also under study, which is to prepare for future coal gasification. Reference is also made to the study of a total system. (NEDO)

  12. FY 1999 Report on the technical results. Part 1. Development of fuel cell power generation technologies (Research and development of molten carbonate fuel cell power generation system); 1999 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. 1. Yoyu tansan'engata nenryo denchi (hatsuden system no kenknyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    This research and development project is aimed at development of the stacking, cooling and operating technologies for the molten carbonate fuel cell power generation systems, to improve service life and performance of these systems and reduce their cost, based on the results obtained so far by the FY 1993. The R and D efforts are directed to (1) technologies for improving stack performance, (2) development of the plant system by operating a 1,000kW class power generation system, and (3) support technologies, e.g., those for stack materials. The item (1) studies 3 stack types, cross-flow, parallel-flow and internal reforming types, including the electrodes, electrolyte-supporting bases and improvement of performance and service life by separator reforming for the cross-flow and parallel-flow types, and installation and operation of a 200kW class stack system for the internal reforming type, where cells are assembled into the system and tested for their operability, after the auxiliary units are PAC-tested. The item (2) installs a 1,000kW class plant, which is operated, after clearing the requirements set by the related laws, e.g., Electric Utility Industry Law, for starting the operation, to achieve the intended targets. The item (3) includes development of the technologies for stack materials, technologies for handling gases produced by coal gasification, and studies on the total systems. (NEDO)

  13. Report on results of development of fuel cell power generation technology 1998. Research and development on polymer electrolyte fuel cell (technological development of element, research on ion exchange membrane for practicability of high performance cell); 1998 nendo seika hokokusho. Nenryo denchi hatsuden gijutsu kaihatsu, kotai kobunshigata nenryo denchi no kenkyu kaihatsu, yoso kenkyu kaihatsu (koseino denchi jitsuyoka no tame no ion kokan maku ni kansuru kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper explains the results during fiscal 1998 of ion exchange membranes in the development of polymer electrolyte fuel cells. Studies were made on three kinds of standard and two kinds of experimental membranes selected among the Flemion membranes, which are perfluorosulfonic acid membranes made by Asahi Glass Co.,Ltd., and also on the Nafion membranes by Dupon as reference. As the resistance evaluation of the environmental cycle for the membranes, a temperature cycle test was carried out, with the characteristics measured such as moisture content, membrane resistance, mechanical properties, and gas permeability, so that the effects were examined of the temperature cycle on the membranes. Evaluation was also commenced on the water permeability, an important substance-moving characteristic of ion exchange membranes. In the evaluation of the characteristics of membrane-electrode assemblies, the environmental cycle test was performed by joining electrodes to membranes, with the evaluation similarly made as for the membranes alone. On the basis of a correlation between the water permeability and the cell performance, studies were made on the effect of thickness of the membranes on the cell performances. A continuous stability/durability operation of 3,500 hours was verified using Flemion R. As for membrane reinforcement, studies were continued on the cloth and fibril reinforcements as in the previous year.(NEDO)

  14. Fiscal 1996 achievement report. Development of liquid fuel conversion technology (Feasibility study project on liquid fuel conversion); 1996 nendo ekitai nenryo tenkan gijutsu kaihatsu seika hokokusho. Ekitai nenryo tenkan kanosei chosa nado jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This article comprises Part 1 on 'surveys of gas fields fit for a new methanol manufacturing process' and Part 2 'reports on overseas surveys of gas fields fit for a new methanol manufacturing process.' In Part 1, surveys are conducted on the existence, exploitation, and the actual utilization of natural gas resources, and on the status of natural gas industry related infrastructures in the Middle East. Proved natural gas reserves in Iran were 742tcf (trillion cubic feet) as of 1996-end, which was the largest in the world next to Russia. As for Kuwaiti natural gas resources, they all accompany oil production, with the proved reserves marking 52.4tcf as of 1996-end or the smallest in the Middle East. In Egypt, there were proved reserves of 20.4tcf as of 1996-end, and further existence of 30-40tcf is predicted. Proved reserves in Yemen are approximately 15tcf. Proved reserves in Oman were 30tcf as of 1996-end. It is expected that there will be a 1.4% increase in the demand for methanol for automobiles. The annual demand for methanol for power generation is 720,000 tons. In Part 2, on-site surveys of infrastructures and the like indispensable for methanol plant installation are reported. (NEDO)

  15. Fiscal 1996 achievement report. Development of liquid fuel conversion technology (Feasibility study project on liquid fuel conversion); 1996 nendo ekitai nenryo tenkan gijutsu kaihatsu seika hokokusho. Ekitai nenryo tenkan kanosei chosa nado jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This article comprises Part 1 on 'surveys of gas fields fit for a new methanol manufacturing process' and Part 2 'reports on overseas surveys of gas fields fit for a new methanol manufacturing process.' In Part 1, surveys are conducted on the existence, exploitation, and the actual utilization of natural gas resources, and on the status of natural gas industry related infrastructures in the Middle East. Proved natural gas reserves in Iran were 742tcf (trillion cubic feet) as of 1996-end, which was the largest in the world next to Russia. As for Kuwaiti natural gas resources, they all accompany oil production, with the proved reserves marking 52.4tcf as of 1996-end or the smallest in the Middle East. In Egypt, there were proved reserves of 20.4tcf as of 1996-end, and further existence of 30-40tcf is predicted. Proved reserves in Yemen are approximately 15tcf. Proved reserves in Oman were 30tcf as of 1996-end. It is expected that there will be a 1.4% increase in the demand for methanol for automobiles. The annual demand for methanol for power generation is 720,000 tons. In Part 2, on-site surveys of infrastructures and the like indispensable for methanol plant installation are reported. (NEDO)

  16. FY 1998 annual report on the conversion of fuel at Igumnovskaya thermal power plant; Igumnovskaya hatsudensho nenryo tenkan 1998 nendo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    As part of the industrially advanced countries' joint action on the basis of the United Nations Framework Convention on Climate Change (UNFCCC), a thermal power plant in Igumnovskaya (I-plant), Russia was selected as the candidate for rationalization by conversion of fuel from coal to natural gas and introduction of combined-cycle generation, for investigation of the effect on reduction of greenhouse gas generation. The I-plant is located in one of the Russia's largest chemical industry regions, supplying power and steam to the factories in the region. The draft rationalization plan adopts a combination of a coal-fired 300,000 kWh plant that has not been completed and obsolete facilities in the I-plant as the reference case. The plan is drafted to construct a 450,000 kWh combined cycle unit and 3-200 t/h boilers, while effectively utilizing the existing facilities. It requires an investment of US$340 million. The construction works are scheduled to start in 2002 for the initial start-up in 2004. It is expected to reduce CO2 emissions by 1.8 million tons a year and cumulatively 52.7 million tons in the 30-year period from 2005. (NEDO)

  17. FY 1998 annual report on the conversion of fuel at Igumnovskaya thermal power plant; Igumnovskaya hatsudensho nenryo tenkan 1998 nendo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    As part of the industrially advanced countries' joint action on the basis of the United Nations Framework Convention on Climate Change (UNFCCC), a thermal power plant in Igumnovskaya (I-plant), Russia was selected as the candidate for rationalization by conversion of fuel from coal to natural gas and introduction of combined-cycle generation, for investigation of the effect on reduction of greenhouse gas generation. The I-plant is located in one of the Russia's largest chemical industry regions, supplying power and steam to the factories in the region. The draft rationalization plan adopts a combination of a coal-fired 300,000 kWh plant that has not been completed and obsolete facilities in the I-plant as the reference case. The plan is drafted to construct a 450,000 kWh combined cycle unit and 3-200 t/h boilers, while effectively utilizing the existing facilities. It requires an investment of US$340 million. The construction works are scheduled to start in 2002 for the initial start-up in 2004. It is expected to reduce CO2 emissions by 1.8 million tons a year and cumulatively 52.7 million tons in the 30-year period from 2005. (NEDO)

  18. Research report for fiscal 1998. Research into the trends of low-carbon automotive fuel manufacturing technologies; 1998 nendo jidoshayo teitanso nenryo no seizo gijutsu doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Studies are made of optimum materials and methods for manufacturing low-carbon fuels for reduction in greenhouse gas emissions. When their thermal dynamic limits and the technological maturity are considered, it is inferred that no extensive improvement will be achieved by merely improving on the efficiency of the existing fuels. The use of various high-efficiency driving power sources utterly different in mechanism from the conventional ones, such as those for fuel cell-powered automobiles, and the promotion of the use of low-carbon fuels such as methanol and methane for all kinds of driving power sources including those for the said fuel cell-powered automobiles, will become necessary. The use will also be necessary of recyclable materials. The biomass resources, in particular, since they absorb CO2 gas in their growing process by virtue of photosynthesis, may be said to be free of CO2 gas emissions. They have their own problems, however, which involve the economy of energy consumed for their production, harvesting, transportation, and conversion into fuels. It is therefore required that their whole life cycle be studied before their greenhouse gas reduction effect may be correctly assessed. The quantities of resources available for the production of automotive low-carbon fuels, manufacturing technologies, etc., are first of all put in order for easy perusal. An effective way is assessed for the whole including the life cycle. (NEDO)

  19. Fiscal 1997 survey report. Basic survey on trends of waste use type production facilities and waste fuel production facilities; 1997 nendo chosa hokokusho. Haikibutsu riyogata seizo shisetsu oyobi haikibutsu nenryo seizo shisetsu doko kiso chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This survey was made to obtain the basic data for future spread and promotion of No.6 type (waste use type production facilities) and No.7 type (waste fuel production facilities) which were added to the objects having been subsidized since fiscal 1997 under `the environmental harmony type energy community project.` In the former, the kiln in the cement industry and the blast furnace in the steel industry can be extremely large places to receive waste plastic since the facilities are distributed in every area and the treatment capacity is large. However, the effective collection, transportation and sorting of large quantity of waste plastic, especially the problem of removal of vinyl chloride, is a big bottleneck. As to the use of waste plastic using gasification technology, there are no actual results on the commercial basis. That is, however, appropriate for treatment of the waste difficult in treatment, and can be expected of the usage in the chemical industry. In the latter, in the facilities using industrial waste raw materials as fuel, solidification and liquefaction are both operated on a commercial basis. In relation to the solidification and use as fuel of general waste, the treatment of combustion ash is preventing the expansion of use of waste in the industrial field because of a large quantity of chlorine included in the products. 92 refs., 54 figs., 35 tabs.

  20. NEDO Forum 2001. Session on hydrogen/PEFC (Toward realization of hydrogen/fuel cell society); NEDO Forum 2001. Suiso PEFC session (suiso nenryo denchi shakai no jitsugen ni mukete)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-20

    The presentations made at the above-named session of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. Introduced in a lecture entitled 'March toward hydrogen/fuel cell society' were NEDO's PEFC (polymer electrolyte fuel cell) related project of its hydrogen energy technology development office and the WE-NET (World Energy Network) hydrogen program. Reported in a lecture entitled 'Toward the practical application of PEFC' were Yamanashi University Clean Energy Center's achievements in the study of polymer electrolyte film, electrodes and separators for PEFC, removal of carbon monoxide by selective oxidation, and so forth. Discussed in a lecture entitled 'Development of high efficiency energy system technologies for transportation and residential/commercial sectors' were the development of a hydrogen-fueled 1kW stack and the result of efforts to develop element technologies for power generation systems fueled by natural gas, methanol, etc. Explained also were the outline and the progress of the project in relation with the fuel cell popularization infrastructure construction project and the fiscal 2001 research and development and the future outlook in relation with the 2nd-phase technology development for WE-NET. (NEDO)

  1. Simulation of PV/FC power hybrid system. Change of system capacity with load form factor; Taiyoko hatsuden nenryo denchi hybrid system no simulation. Fuka keijoritsu ni yoru system yoryo no henka

    Energy Technology Data Exchange (ETDEWEB)

    Sekiguchi, N.; Tani, T. [Science University of Tokyo, Tokyo (Japan)

    1997-11-25

    Study is conducted of a photovoltaic/fuel-cell hybrid system whose power storage is a hydrogen storage that uses a hydrogen absorbing alloy. In a simulation in this research, the solar cell conversion efficiency is changed from 15.0% to 21.0% and the fuel cell power conversion efficiency from 40.0% to 50.0%, and the resultant changes in the capacity and operation rate are investigated for each of the devices in the system. The findings follow. A 1.0% change in the solar cell conversion efficiency results in a 4.8kW change in the solar cell capacity and a 1.6-ton change in the hydrogen storage capacity. With a 1.0% change in the fuel cell power conversion efficiency, there is a 14.7kW change in the solar cell capacity and a 5.3-ton change in the hydrogen storage capacity. The fuel cell capacity is not dependent on the solar cell conversion efficiency or fuel cell power conversion efficiency but on the maximum load in each of the load form factors. The rate of occurrence of an operation rate of less than 30% is 54.7% both in DC/DC converter and hydrogen generator, 24.6% in fuel cells, and 16.7% in the DC/DC inverter. 7 refs., 7 figs., 1 tab.

  2. Fiscal 1996 survey report. Data collection and evaluation analysis in the project on field tests on the fuel cell generation; 1996 nendo kenkyu hokokusho. Nenryo denchi hatsuden field test jigyo ni okeru data shuyaku oyobi hyoka kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper installed fuel cell power generation equipment experimentally at various facilities which are the final diffusion form of the new energy power generation, conducted long-term operation under the actual load, collected/analyzed various data, arranged them as data useful for full scale introduction/diffusion, aiming at forming the base for general diffusion of the fuel cell power generation. The number of the systems installed for field test execution has been 24 places/28 units since the start of the project, and the system capacity totaled 4,250kW. The actual operation hours in five years are 6,000-28,000. In fiscal 1996, the average cumulative accumulated operational rate was approximately 68%, a little over that in fiscal 1995, 65%. The average load factor was 69% in fiscal 1995 and 70% in fiscal 1996. The utilization rate increased as a whole to about 57% on average if seeing only fiscal 1996, as compared with that in fiscal 1995, about 48%. The power generating efficiency was approximately 34% on average. As to the status of shutdown of the fuel cell power generation, the paper surveyed the average interval of failure, the rate of frequency of shutdown, the analysis of shutdown, etc. 250 figs., 29 tabs.

  3. FY 1994 report on the results of the R and D of solid oxide fuel cells (SOFC); 1994 nendo SOFC kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-01

    Development of fuel cell power generation technology and R and D of solid oxide fuel cells were carried out, and reports of the FY 1994 results of companies were summed up. As to the R and D of the cell module, R and D were conducted of 'large area cell' by Fuji Electric Corporate R and D, Ltd. and 'combined cell module' by Sanyo Electric Co. As to the R and D of materials/basic technology, the following were conducted: 'R and D of the electrode micro structure' by Japan Fine Ceramics Center, 'R and D of the electrode structure by thermal spraying method by Fujikura Ltd., 'R and D of the multi-functional fuel electrode' by Mitsubishi Heavy Industries, Ltd., 'R and D of the cofiring technology' by Murata Mfg. Co., and 'R and D of the current collecting technology' by Mitsui Engineering and Shipbuilding Co. Concerning the R and D of the system, 'the system study' by Central Research Institute of Electric Power Industry' and 'development of element technology for periphery devices' by The Japan Research and Development Center for Metals. (NEDO)

  4. Fiscal 1999 research cooperation project. Research cooperation on community-oriented practical photovoltaic power systems (Practical methane gas fermentation fuel cell power systems); 1999 nendo metan hakko gas nenryo denchi hatsuden system no jitsuyoka ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report describes the research cooperation with developing countries on practical methane gas fermentation fuel cell power systems in 1999-2002. This research aims to construct the methane gas fermentation fuel cell power facility using livestock excreta which can supply power to the facility and peripheral areas. The facility controls various substance concentrations in waste water within environmental standards, and uses waste as compost. This project is very promising in use of environment-friendly energy, effective use of unused energy and power supply to unelectrified areas for China under serious conditions such as rapid increase in energy demand and various environment problems. There are such various issues to achieve this target as securing livestock (pig breeders) and excreta, and fermentation and recovery of suitable methane gas necessary for fuel cell power systems from excreta. This report is composed of 2 parts, (1) Current use of energy resources and use of unused energy in Guangdong province, and (2) Technical requirements for practical methane gas fermentation fuel cell power systems. (NEDO)

  5. FY1992 research report on the evaluation and analysis of data collected in fuel cell power generation field test project; 1992 nendo nenryo denchi hatsuden field test jigyo ni okeru shushu data hyoka kaiseki kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This paper describes the achievements in fiscal 1992 in the field tests on fuel cell power generation systems. The three locations subjected to the present analysis are all installed with 50-kW systems, whereas power generation efficiency of around 35% such as 35.3, 34.2 and 34.6% was obtained when the systems were operated at the rated output. When the load gets to below a certain load band (about 30 kW), the power generation efficiency decreases proportionately with the load. The overall efficiency including heat supply was 77.8, 70.7 and 80.3% respectively at about the rated output, showing a trend that the higher the thermal efficiency, the higher the overall efficiency. The case of generating both electric power and heat simultaneously has higher efficiency than the case of heat supply alone. The contribution rate of the fuel cell as a base load was 2.8, 4.6 and 13.6%, respectively. The system with as high value as 13.6% takes a power load following type operation mode, in which power is generated during a time band with large load during weekdays, and no power is generated at nighttime and in holidays when load is smaller, playing a role of peak responding power supply. Only one trouble has occurred in an auxiliary generator in the heat recovery system. (NEDO)

  6. FY 2000 report on development of the infrastructure to promote use of fuel cells for automobiles. For safety and environmental factors; 2000 nendo jidoshayo nenryo denchi no fukyu kiban seibi seika hokokusho. Anzensei shuhen kankyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the results of the FY 2000 activities for safety and environmental factors involved in fuel cell powdered vehicles. The current technical standards and specifications for CNG and LPG fueled vehicles are investigated, to extract the factors necessary to establish the safety evaluation guidelines when these fuels are replaced by hydrogen fuel. The rules extracted and studied include those related to collision and resultant fuel leakage, removal of spark and hot sources, leakage in the fuel system, leakage into containers and passenger rooms, and materials. For the rules on test methods of fuel tanks, the investigated items include fire resistance, impact resistance and permeation loss of fuel from the tanks. For system safety, the investigated items include possible unusual situations, leakage of the electrolytes and electrical shock. The basic data are collected for destruction of the fuel tanks, spout of hydrogen from and electrification of the hydrogen-occluding alloys, flame retardancy of high-voltage wires for automobiles, and hydrogen diffusion simulation. The safety-related technical trends are followed by hearing the related organizations, including automakers. Literature survey and hearing are conducted to investigate the environmental effects of radio wave interference and noise. (NEDO)

  7. FY 1994 report on the results of the R and D of solid oxide fuel cells (SOFC); 1994 nendo SOFC kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-01

    Development of fuel cell power generation technology and R and D of solid oxide fuel cells were carried out, and reports of the FY 1994 results of companies were summed up. As to the R and D of the cell module, R and D were conducted of 'large area cell' by Fuji Electric Corporate R and D, Ltd. and 'combined cell module' by Sanyo Electric Co. As to the R and D of materials/basic technology, the following were conducted: 'R and D of the electrode micro structure' by Japan Fine Ceramics Center, 'R and D of the electrode structure by thermal spraying method by Fujikura Ltd., 'R and D of the multi-functional fuel electrode' by Mitsubishi Heavy Industries, Ltd., 'R and D of the cofiring technology' by Murata Mfg. Co., and 'R and D of the current collecting technology' by Mitsui Engineering and Shipbuilding Co. Concerning the R and D of the system, 'the system study' by Central Research Institute of Electric Power Industry' and 'development of element technology for periphery devices' by The Japan Research and Development Center for Metals. (NEDO)

  8. FY 2000 report on the results of development of technology for commercializing high-efficiency fuel cell systems. Development of technology for commercializing high-efficiency fuel cell systems (Development of technology for effective utilization of power produced by polymer electrolyte fuel cell systems); 2000 nendo kokoritsu nenryo denchi system jitsuyoka gijutsu kaihatsu seika hokokusho. Kotai kobunshigata nenryo denchi no shutsuryoku yuko riyo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This project is aimed at development of technologies for effective utilization of power produced by polymer electrolyte fuel cell (PEFC) systems and waste heat, to spread cogeneration systems incorporating PEFC systems for residential purposes. Described herein are the FY 2000 results. The program for high-efficiency peripherals for residential PFEC systems attempts use of GaN-FET as the semiconductor device of wide band gap and high breakdown voltage to realize conversion efficiency over 90% by improving inverter efficiency. Two types of the prototype heat recovery systems are developed for the PEFC, one incorporating a latent heat cooling system and the other a water cooling system, to improve heat recovery efficiency and increase heat recovery temperature. The program for technology to fit PEFC output to energy demand develops hot water supply systems provided with a hot water storage function for stable supply of hot water irrespective of the heat recovery conditions, and also with a back-up function with burners. The program also develops the PEFC system of fine load following characteristics, for which pure hydrogen is used as the fuel to allow the system to instantaneously follow fluctuating loads. The program for high-efficiency partial load operation technology studies a 1kW-class residential PEFC cogeneration system incorporating a power storage device for high-efficiency operation at partial loads, where the former operates in a high output mode while the latter absorbs fluctuating loads. (NEDO)

  9. Fiscal 1996 result reports of the researches under consignment from NEDO. Developments of fuel cell technology, polymer electrolyte fuel cell, fuel cell power generation system technology, and high-voltage type several tens kW class distributed power source system; Shin energy sangyo gijutsu sogo kaihatsu kiko itaku gyomu 1996 nendo seika hokokusho. Nenryo denchi gijutsu kaihatsu, kotai kobunshigata nenryo denchi no kenkyu kaihatsu, hatsuden system gijutsu kaihatsu, koden`atsugata suju kW kyu bunsan dengen system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This paper precisely reports the research result on development of fuel cell technology in fiscal 1996. On verification of cell durability, the cell test result in hydrogen including CO of 100ppm using Pt-Ru catalyst as CO resistant catalyst showed that the loss percent of cell voltage decreases with an increase in Ru content. On development of stack technology, the carbon humidification plate superior in chemical stability was developed as one of the parts for layered stacks. The separator with a water- permeable carbon plate and serpentine flow fields was fabricated for highly layered stacks, and achieved the target performance in single cell power generation test. On establishment of design basis for compact fuel processor, the bench-scale test was conducted of Ru/{gamma}-Al2O3 and Pt-Ru/{gamma}-Al2O3 catalysts as advanced CO selective oxidation catalyst for CO reducers. On demonstration test for the several tens kW class stationary power plant, the system configuration of power generation plants using natural gas as fuel was studied. 106 figs., 38 tabs.

  10. Technological development for super-high efficiency solar cells. Survey on the commercialization on analysis; Chokokoritsu taiyo denchi no gijutsu kaihatsu. Jitsuyoka kaiseki ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the survey results on analysis of super-high efficiency solar cells for practical use in fiscal 1994. (1) On the survey on crystalline compound solar cells, it was pointed out that the present study target is III-V compound semiconductor solar cell, and efficiencies of 36-39% are theoretically expected by use of two-junction cells. (2) On structure of super-high efficiency solar cells of 40%, selection of upper and lower cell materials for multi-junction cells, high-efficiency tandem Si solar cells, and the merit and possibility of light collection operation were surveyed, and their issues were discussed. (3) On physical properties of mixed crystalline semiconductors and characteristic evaluation of solar cells, impurities, trap center, minority carrier life, and applicability of supper lattice structure to high-efficiency solar cells were surveyed. (4) On fabrication technology of compound semiconductor solar cells, various problems of and approaches to electrode formation and antireflection film technologies, the meaning and issues of thin film substrate technology and continuous process, trial calculation of costs, safety, and resource problem were surveyed.

  11. FY 2000 report on development of the infrastructure to promote use of fuel cells for automobiles. Establishment of the base data for fuel quality standardization; 2000 nendo jidoshayo nenryo denchi no fukyu kiban seibi seika hokokusho. Nenryo seijo kikakuka no tame no base data chikuseki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This project is aimed at studies on the effects of impurities and additives in hydrogen and methanol fuels, to establish the base data for fuel quality standardization and thereby to promote use of fuel cells for automobiles. Described herein are the FY 2000 results. Literature survey is conducted for the effects of the impurities on performance of the cells and hydrogen-occluding alloys, and various additives for improving safety, e.g., odorants, flame visualizers for hydrogen, and fuel colorants and flame visualizers for methanol. Under the present standards, the cell and alloy performance may be affected by the impurities, e.g., CO and sulfur compounds. The commercial products are sampled, to analyze the impurity components and their concentrations. Hydrogen produced by various processes contains a high proportion of CO before being refined, which may adversely affect the performance. Methanol sampled from less frequently used refilling stations contains high proportions of carbonyl compounds, and it is necessary to confirm their effects of the reformer. In order to investigate the effects of impurities, the performance tests are conducted using the test apparatuses for performance evaluation of power generation by fuel cells and hydrogen-occluding alloys. Propane is found to be an effective flame visualizer for hydrogen, but should be contained at 5% or more to visualize the flame. (NEDO)

  12. Research on the general analytical method of fossil fuel cycle from a viewpoint of the global environment. 3; Chikyu kankyo kara mita sogoteki kaseki nenryo cycle bunseki hyoka shuho no chosa. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The general analysis/assessment method of a fossil fuel cycle was studied. Seven kinds of power generation plants such as LNG cycle and coal cycle ones, and four kinds of transport and treatment systems of recovered CO2 such as ocean and underground systems were studied as case studies on life cycle analysis. As data necessary for life cycle analysis, the database was constructed which stores the facilities and operational energy required for a total energy system from mining of fossil fuel to treatment of recovered CO2, and the quantity of environmental waste such as CO2 emission. As a result, the decrease rate of energy balance defined as ratio of input energy to power plant output was estimated to be 14-43% and 20-60% in LNG cycle and coal cycle, respectively. Even if the recovery rate of CO2 in power plants reached 80-90%, reduction of total CO2 emission was limited to only 20-40% because of CO2 emission during mining, liquefaction and transport of fuel. 168 refs., 48 figs., 102 tabs.

  13. Report on the survey of the commercialization of wood biomass energy. Project on the production of wood pellet fuel; 2001 nendo mokushitsu baiomasu energy jigyoka chosa hokokusho. Mokushitsu peretto nenryo seizo jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-02-01

    For the purpose of regenerating forestry and contributing to the policy for prevention of global warming, a potential study was made of the commercialization of the wood pellet using low-quality wood materials such as thinnings and wood pieces from lumber mill. In the study, based on the survey of raw materials of wood pellet and the demand amount, the scale of pellet production was assumed, and subjects were arranged toward the basic design of plant, evaluation of economical efficiency and commercialization. As a result of the study, the following subjects were extracted. In the study, the supply of lumbers of 2,800 t/y and securing of demand of about 1,600 t/y were set forth as a premise, but the subject was to secure the initial demand. The pellet combustor was higher in price than the kerosene combustor, and for the imported combustion equipment, the combustion of white pellet was supposed. It is necessary to develop combustor of pellets including the bark. In the trial calculation of the unit price of heat utilization (yen/Mcal), the pellet stove was about 3.3 times as high in price as the kerosene stove. It is necessary to reduce the pellet price down to 30 yen/kg or so by decreasing the cost of pellet production. (NEDO)

  14. FY 1999 report on the model project on the effective utilization of waste-base biomass fuels. Basic survey for the feasibility; 1999 nendo haikibutsukei biomass nenryo yuko riyo model jigyo jisshi kanosei kiso chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Survey on the waste biomass was conducted for Thailand, Malaysia, Indonesia, Vietnam, Laos, Nepal, Butan, Myanmar and Cambodia to study feasibility of the project for the concrete utilization of biomass resources. In Thailand, it is expected to construct large-scale model plants for biomass resources such as rice hulls, bagasse, wood waste and oil palm. In Malaysia, expected are the cogeneration at 5MW class palm oil plant, large-scale power plant using wood waste, plant using the biomass from waste palm oil, etc. In Indonesia, there is a great potentiality, but it is necessary to handle it carefully in consideration of the unstable situation of the society. In Vietnam, the detailed survey of feasibility is needed on the project for efficiency heightening at state-run plants, the assumed national plants (recommended by the government), etc. In Laos, small-scale power generation using the forestry waste such as sawdust is expected. (NEDO)

  15. FY 2000 report on the results of the development of transportation use and residential/commercial use high efficiency energy system technology. R and D of polymer electrolyte cells (Research on ion exchange membranes for commercialization of highly durable cells); 2000 nendo unyu minsei you kokoritsu energy system gijutsu kaihatsu seika hokokusho. Kotai kobunshigata nenryo denchi no kenkyu kaihatsu (Kotaikyusei denchi jitsuyoka no tame no ion kokanmaku ni kansuru kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As to ion exchange membranes for fuel cells, the R and D were made with the aim of clarifying the characteristics of the membrane required to realize highly durable modules and of demonstrating durability of membrane, and the FY 2000 results were reported. Concerning the low ion exchange capacity thin membrane, the following were confirmed: in perfluorosulfonic acid with ion exchange capacity of 0.84-1.0, the lower the ion exchange capacity is, the greater characteristics of mechanical strength are improved; the optimization of membrane thickness makes the design which satisfies cell characteristics and mechanical strength characteristics possible. In the durability test by medium-/long-term continued operation using each of small unit cell and large unit cell, the results of the stable operation of 5,000 hours using S1102 and S1201Q membranes were obtained. About effects of methanol, changes were observed in creep characteristics and piercing strength in the test on the environmental cycle at -40 degrees C to 80 degrees C. The membrane of low ion exchange capacity kept high elastic modulus even after the treatment at 120 degrees C, which indicated its usability for the higher temperature operation. (NEDO)

  16. Development of technology for thin substrate polycrystalline solar cells for practical use. Survey on analysis for practical use; Usugata takessho taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Jitsuyoka kaiseki ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the survey results on the manufacturing technology trend of thin substrate solar cells for practical use in fiscal 1994. In production of Si raw material, as electron beam melting and ingot production are combined, C, P, Ca and Al are removed by evaporation, while Fe and Ti by solidifying segregation. As the basic technology of continuous casting for substrate production, a drop coagulation method for Si melt is under investigation which is more advantageous in unidirectional solidification and cell conversion efficiency than conventional methods. The cost and future of single crystal Si and polycrystal Si were compared on the basis of document survey. Every institute commonly uses FZ substrates to produce single crystal Si cells, and SiO2 for surface passivation. New cell structure, hetero-structure, thin cell, crystalline defect and lifetime are under investigation for ultrahigh-efficiency solar cells. The technology trend was also surveyed through academic societies and conferences. 5 tabs.

  17. Research and development of evaluation system for photovoltaic power generation system. Survey on research and development of solar cell evaluation system; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. Taiyo denchi hyoka system no kenkyu kaihatsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the survey results on R and D of solar cell evaluation systems in fiscal 1994. The performance/reliability evaluation subcommittee continuously analyzed technical issues and discussed solution measures from the last fiscal year. On development of performance evaluation methods, improvement of measurement accuracy for laminated solar cells is the study issue to be solved. Although laminated solar cells are measured by multiple light source solar simulator, difficult spectrum compensation causes measurement errors. Collection and analysis of data for determining atmospheric conditions, and outdoor measurement experiment under the atmospheric conditions for reference solar light were carried out. The study on incident angle characteristics of laminated solar cells clarified that the deviation from COS characteristics is 1.0% or less at an incident angle of 30{degree}. The study on generated energy in solar cell module level in field clarified that generated energy and generation efficiency are proportional to intensity of solar radiation. 1 tab.

  18. Research on fabrication technology for thin film solar cells for practical use. Survey on the commercialization analysis; Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Jitsuyoka kaiseki ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the survey results on the technological trend, safety and latest technologies of thin film solar cells in fiscal 1994. As the fabrication technology for amorphous film solar cells, three-electrode plasma CVD was surveyed as fabrication method for high-mobility materials, and hydrogen radical CVD as fabrication method for high-photostable films. Current foreign and domestic reliability tests were surveyed for reliability evaluation of solar cells. In order to ascertain the performance, efficiency, physical properties and optimum structure of polycrystalline Si thin film solar cells, previously reported test results on physical properties such as carrier concentration, carrier lifetime and mobility of films were surveyed together with device simulation results. In addition, technologies for high-efficiency CuInSe2 system and CdTe system solar cells, technologies for cost reduction and mass production, and environmental influence were surveyed. Estimation of production costs for cell modules, and safety of thin film solar cells were also surveyed.

  19. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of solar cell evaluation system (Survey of research and development of solar cell evaluation system); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo denchi hyoka system no kenkyu kaihatsu (taiyo denchi hyoka system no kenkyu kaihatsu chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The fiscal 1999 results of survey and research conducted for the establishment of solar cell performance evaluation and reliability evaluation methods are reported. In the development of a super high fidelity (broad spectrum) solar simulator for cell evaluation, a prototype was tested for performance evaluation, and initially set values were achieved. In the development of a large-area module evaluation technology, the radiation area was increased to be 1.0m times 1.0m large. Outdoor exposure tests continued at 5 sites in Japan, 3 sites in Australia, and 1 site in Oman, and analyses and databasing were carried out for the outputs of various types of solar cell modules. As for the problem of coloring of fillers which are module constituents, coloring in the U.S. was attributed to high temperature and intensive insolation, and in Austria to an oxidation inhibitor. In the development of a photo-accelerated degradation testing method for Si-based solar cells, application of the cycled illumination test was found feasible. In this test method, an amorphous silicon solar cell retains 70% of the initial Pmax value even after the passage of a period equivalent to 30 years. (NEDO)

  20. Report on commissioned business for fiscal 1997. Development of new power storage system for cells and development of technology for distributed power storage (research for a zinc/air cell system for automobiles); 1997 nendo itaku gyomu hokokusho. Shingata denchi denryoku chozo system kaihatsu bunsangata denryoku chozo gijutsu kaihatsu (denki jidoshayo aen kuki denchi system chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Concerning the above, it is discussed whether such a system is feasible in Japan. A zinc/air cell system requires some special plants for zinc regeneration, etc. It is necessary to build a zinc refining plant and to install dozens of electrode replacing facilities in an area dozens of kilometers in diameter with the plant at the center. For such a system to be functional, there have to be several tens of thousands of automobile users in a limited area. In Japan, so large a number will not be found anywhere even if the appeal is directed to those in the postal service and electric utilities. There will be no economic success in Japan, different from in Germany. As for the economic comparison between a zinc/air cell system and natural gas system, the two will be equivalent to each other as far as the use of the quick filling stations for the natural gas automobiles remains as it is. When the number in consideration is so large as several tens of thousands, however, the natural gas system will turn out to be economically superior to the zinc/air cell system. 19 figs., 29 tabs.

  1. Fiscal 2000 survey report. Development of novel battery power storage system (Development of distributed power storage technology - Marketability of lithium storage battery); 2000 nendo gyomu hokokusho. Shingata denchi denryoku chozo system kaihatsu - Bunsangata denryoku chozo gijutsu kaihatu (Ritium niji denchi no shijosei chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A survey is conducted of the current status of storage batteries and the marketability of the lithium ion battery. In the study of future marketability of storage batteries for electric vehicles, the small vehicle Hypermini currently loaded with a lithium ion battery is taken up and it is assumed that each carries a 10 kWh battery, and then it is estimated that there will be an approximately 2200 times 10{sup 3} kWh market in Japan in 2020. As for hybrid vehicles each loaded with a 1 kWh battery, it is estimated that 3997 times 10{sup 3} kWh will be on the market in 2020. For the fuel cell powered vehicle, similarly, there will be approximately 2,500 times 10{sup 3} kWh on the market in 2020. As for power storage facilities for power load shaving, the demand for cells in 2020 is estimated at 1,032-3,924 times 10{sup 3} kWh on the assumption that they operate 4 hours in the daytime. As for the uninterruptible power supply, it is estimated that 800 times 10{sup 3} kWh will be required by those installed at data centers in 2020. It is also estimated that 252 times 10{sup 3} kWh will be necessary in the form of storage batteries for motored wheelchairs in 2020. As for distributed power source systems such as those dealing with wind power or photovoltaic power, there are a number of technical problems that have to be settled. (NEDO)

  2. Fiscal 1994 achievement report. Development of photovoltaic power generation system practicalization technology - Development of ultrahigh-efficiency solar cell technology (Development of new photoelectric conversion material technology - Research on future feasibility of wet-type solar cells); Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Chokokoritsu taiyo denchi no gijutsu kaihatsu (shinkoden henkan zairyo no gijutsu kaihatsu (shisshiki taiyo denchi no shoraiteki kanosei no chosa))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    A survey is conducted of wet-type solar cells that may constitute an important field in solar chemistry. The wet type solar cell made known by Graetzel et al. in 1991 is a combination of ultrafine TiO{sub 2} grains and a sensitizing dye. The ultrafine grain surface structure enlarges the area of an electrode for the absorption of 46% of incident solar radiation of which 80% or more is converted into electric power. The fill factor at 520nm of a cell fabricated for an additional test turns out to be 40% against the 76% mentioned in technical literature, and the conversion efficiency 10%. The Titanyl sulfate is also tested because it is low in price as material for titanium oxide. Functional groups are experimentally introduced for the generation of bonds on the substrate to be effective in the injection of a sensitizing dye. A sensitizing dye with two carboxyl groups and two bipyridine rings as ligand is allowed to be supported by TiO{sub 2}. IR (infrared) spectrometry is performed, and then formation is found of ester-like bonds or chelate bonds due to the interaction of carboxyl groups and the substrate surface. This is enhanced by surface treatment. (NEDO)

  3. Fiscal 1999 report. Development of an electric power storage system using new type batteries, and development of a discrete type electric power storage technology (Survey on trend in developing batteries for electric power storage); 1999 nendo shingata denchi denryoku chozo system kaihatsu bunsangata denryoku chozo gijutsu kaihatsu hokokusho. Denryoku chozoyo denchi no kaihatsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Demand is increasing in recent years in Japan on batteries for electric power storage to respond to load variation in electric power supply. If electric power storage batteries are applied for practical use, nighttime excess power can be stored appropriately, which can be discharged during day time when the demand is increased, so that the demand variation can be handled adequately. Secondary batteries, if used, are characterized by having much greater energy density and output density because of storing the electric energy as chemical energy than in pumped-storage power generation which stores the energy as the positional energy of water. Therefore, this paper describes the surveys performed on the trend of developing the power storage batteries inside and outside the country. Section 1 shows the current status of annual load rates in other countries, and the current conception on power storage in these countries. Section 2 states the current status of practical application of power storage batteries having been developed in Germany and the U.S.A. and performed of demonstration tests. Section 3 reports the current status of developing new type power storage batteries. Section 4 describes the current status of developing the power storage batteries for power users. (NEDO)

  4. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Research and survey of peripheral element technologies (Research on practical application of set solar cell); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu / shuhen yoso gijutsu ni kansuru chosa kenkyu (shisshiki taiyo denchi jitsuyoka kanosei chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Possibility of practical application of dye-sensitized solar cells (Graezel cells) is discussed. Fine titania particle preparation conditions and titania thin-film electrodes were optimized and an energy conversion efficiency of 7.7% was accomplished. The screen printing method was applied to the manufacture of dye-sensitized electrodes, and performance governing factors were grasped. The use of the screen printing method resulted in a conversion efficiency of 6-8.4% when the factors were optimized. Though lower than the 10% in the Graezel report, values near that were obtained. The status of latest research and development is compiled involving studies about electron transfer dynamics in dye-sensitized solar cells, manufacture of sensitizing dyes and mesoscopic metal oxide thin-film, electron transfer layers and their physical properties, and solidification of hole transfer layers. Research was conducted aiming at their practical application, and tasks and problems in each of the said items were point out. A logical approach to achieve high conversion efficiency was deliberated, and studies were made about how to propel forward endeavors involving design guidelines for high-performance sensitizing dyes, design and preparation guidelines for thin film for electrodes, analysis of stability, solidification of the redox electrolyte, etc. (NEDO)

  5. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology (Survey of peripheral element technologies - Survey of environmental adaptation of next-generation solar cell development); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (shuhen yoso gijutsu ni kansuru chosa kenkyu - jisedai taiyo denchi kaihatsu kankyo tekioka chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Surveys are conducted of photovoltaic power system development projects and their utilization in Japan and overseas, and a discussion is made on the progress, technical challenges, effects, and implementation systems relating to the solar cell application technology development project under the New Sunshine Program. Compiled in the report are the results of surveys of the research and development of photovoltaic power systems and their diffusion in the U.S. and European nations, and the research and development strategies for and the trends of the development of various types of solar cells in these countries. The trends of research and development of non-conventional type solar cells are also collected, which include 3 cases of TPV (thermophotovoltaic) devices, 5 cases of new inorganic materials, 1 case of new organic materials, and 4 cases of dye-sensitized solar cells. In relation to the status of resources of crystalline compound-based solar cell materials, raw materials for solar cells other than silicon are taken up, and their reserves, manufacturing methods, quantities yielded and consumed, costs, etc., are surveyed. These are all taken into consideration in discussing the basic approach to the study of future research and development as it ought to be. (NEDO)

  6. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology (Survey of peripheral element technologies - Survey of novel voltaic cell structure solar cell development); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (shuhen yoso gijutsu ni kansuru chosa kenkyu - shinhatsuden soshi kozo taiyo denchi kaitaku no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The present state and trend are surveyed of organic ferroelectric thin films, new carbon materials, fullerene compounds, and thermophotovoltaic (TPV) power. In the study of organic ferroelectric thin-film solar cells, the effort still remains at the basic stage, with the conversion rate as low as 3% in Europe and 2% in Japan. The progress of basic studies, however, is worth attention. It is deemed that 15% is the photoconversion rate to be currently expected from new carbon material solar cells. Fullerene compounds include some semiconductors whose bandgap values may be controlled across a 0.75-1.95eV range, and they may find their place in thin-film solar cells. However, their physical properties are not fully known, and their development into devices such as solar cells is scarcely reported. The research and development of TPV in the U.S. is led by NASA (National Aeronautics and Space Administration) and NREL (National Renewable Energy Laboratory), with their efforts concentrated on the development of portable power sources utilizing combustion heat. In Europe, TPV application to small-scale residential cogeneration systems is under study. (NEDO)

  7. New Sunshine Program for fiscal 2000. Development of photovoltaic power system commercialization technology (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Surveys and studies of peripheral key technologies/Feasibility study of wet-type solar cell commercialization); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu, Shuhen yoso gijutsu ni kansuru chosa kenkyu - Shissiki taiyo denchi jitsuyoka kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Dye-sensitized solar cell commercialization was studied for feasibility. Studies were made about photoelectric conversion efficiency and various factors supposedly to affect the life and other properties, and a wet-type (dye-sensitized type) solar cell was fabricated. In an endurance test, the dye-sensitized solar cell retained its initial performance after 3,500 hours of continuous irradiation. A 16 cm{sup 2}-large integrated type Graetzel cell was fabricated, and it achieved a photoelectric conversion efficiency of 4.6%. Furthermore, in the study of Graetzel cells, possibility of the creation of new electrolytic solutions was discussed, a non-TiO{sub 2} dye-sensitized solar cell was fabricated based on the self-assembled electrodeposition of the ZnO dye, and the feasibility was deliberated of a dye-sensitized solar sell using a composite oxide semiconductor. Concerning their development in the future, it was concluded that dye-sensitized solar cells including the Graetzel cell were equipped with the basic characteristics of a next-generation solar cell that would be requested to be low in cost and high in performance. (NEDO)

  8. New Sunshine Program for fiscal 2000. Development of photovoltaic power system commercialization technology (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Surveys and studies of peripheral key technologies/Surveys of ultrahigh-efficiency solar cell application fields); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu, Shuhen yoso gijutsu ni kansuru chosa kenkyu (Chokokoritsu taiyo denchi tou oyo bunya kaitaku chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Surveys and studies were conducted in order to make propositions concerning the fields of application wherein the merits of ultrahigh-efficiency solar cells would be fully utilized. A questionnaire was held about solar cell application fields, and studies were made about new systems based on the need in the market for specific solar cell goods and capable of supporting their mass diffusion. Proposed as the result was the establishment of a rental (lease) system for photovoltaic power systems, a local photovoltaics advisory system, a market for used photovoltaic power systems, and so forth. In the feasibility study of photovoltaic power generation on unused land in agricultural villages, surveys were conducted concerning energy problems, the energy structure, the actual state of energy consumption, the abandoned farm and its utilization, and so forth. Propositions involving photovoltaic power feasibility were then made, which covered power consumption for greenhouse culture, energy supply for producing methanol out of biomass, power sources for insect incapacitating yellow fluorescent lamps, power sources for livestock barn air-conditioning, power sources for animal excretion treatment, and so forth. (NEDO)

  9. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Research and survey of peripheral element technologies (Research and survey for development of solar cell of new power generation device structure); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu / shuhen yoso gijutsu ni kansuru chosa kenkyu (shinhatsuden soshi kozo taiyo denchi kaitaku no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Attention is paid to behavior at the molecular level with reference taken to the photosynthetic mechanism, and a behavioral mechanism is proposed, which incorporates, in place of the conventional band model, a concept of a molecular structure based on electron transfer, excitation energy transfer, and reactions of oxidation and reduction. Discussion is then made on elements of technology development for the embodiment of high-efficiency organic ferroelectric thin-film solar cells. The elements taken up include the feasibility of organic ferroelectric thin-film cells, photoelctric conversion systems of plants and photosynthetic bacteria, solar cells using donor-acceptor type dyes, organic thin-film solar cells using conductive polymers, and efficient photoexcitation of organic dyes. Fullerene compounds are semiconductive and their band gaps may be controlled to stay within the range of 0.75-1.9eV, and this justifies a hope that they will serve as solar cells. As for TPV (thermophotovoltaic) conversion, it is under development mainly at NASA (National Aeronautics and Space Administration) as a transportable power source based on heat of combustion. Efforts are also being exerted since 1990 in five European countries to develop TPV systems for small-scale cogeneration. (NEDO)

  10. FY 1974 report on the results of the Sunshine Project. Comprehensive study of hydrogen use subsystem and study on the periphery technology (Study on fuel cell system); 1974 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Nenryo denchi system kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-03-01

    In this paper, surveys were conducted on 'the developmental situation of the body of fuel cell' and 'the performance required for the inverter connecting fuel cell and electric power system and the peripheral device, and fuel cell.' However, the economical evaluation was to be made at an appropriate time, and the FY 1974 survey was limited to the technology. The results of the investigational study made based on the above-mentioned policy were described in and after Chapter 2. In Chapter 2, described were the prospects of fuel cell and the guide for this fiscal year. In Chapter 3, the relative evaluation of various kinds of fuel cells in terms of the following: electrode structure, catalyst, cell stack, auxiliary machine, dynamic characteristics of cell, efficiency, life, reliability, maintenance, safety, environmental safety, construction cost, maintenance/running cost, and material cost. In Chapter 4, the present technical situation of inverter and the peripheral device, and the situation of the future R and D in Japan and abroad. In Chapter 5, the positioning of the fuel cell system in the hydrogen energy system, and various kinds of performance required for structural elements. (NEDO)

  11. Fiscal 2001 achievement report. Development of coal gas production technology for fuel cells - Research using pilot test facility - for public release (Test result report - 1/3); 2001 nendo seika hokokusho (Kokai you). Nenryo denchi you sekitan gas seizo gijutsu kaihatsu - Pilot shiken setsubi ni yoru kenkyu (Shiken kekka hokokusho 1/3)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the development of a coal gasification furnace optimum for fuel cells, a pilot test facility was constructed, and the results of tests and inspections conducted therefor are put together. They include a test of the motor-operated valve, individual test of the gasification furnace circulation water pump, individual test of the motor for the same, individual test of the SGC (syngas cooler) circulation water pump, individual test of the coal feeder rotary valve, individual test of the foreign matters extraction rotary valve, individual test of the foreign matters classifier, individual test of the char feeder rotary valve, individual test of the slag conveyer, individual test of the slag vibrator, individual test of the slag crusher, individual test of the slag separation tank exhaust blower, individual test of the slag separator water pump, test of gasification furnace interlocking, verification test of alert for the same, test of gasification furnace system pressure rise, test of oxygen line ventilation, test of comprehensive purge master sequence, verification test of distribution performance of the distributor, test on char system rock hopper pressure application and pressure release, test of pneumatic actuator valve loop, actual operational test of the soot blower, and an individual test of the receiving conveyer. (NEDO)

  12. Fiscal 2001 achievement report. Development of coal gas production technology for fuel cells - Research using pilot test facility - for public release (Test result report - 3/3); 2001 nendo seika hokokusho (Kokai you). Nenryo denchi you sekitan gas seizo gijutsu kaihatsu - Pilot shiken setsubi ni yoru kenkyu (Shiken kekka hokokusho 3/3)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the development of a coal gasification furnace optimum for fuel cells, a pilot test facility was constructed, and the results of tests and inspections conducted therefor are put together. They include a test operation of the expansion turbine in the air separation facility, test operation of the lubricating oil pump for the expansion turbine in the same, test operation of the oxygen compressor in the same, test operation of the medium pressure nitrogen compressor in the same, test operation of the lubricating oil pump for the medium pressure nitrogen compressor in the same, test operation of the high pressure nitrogen compressor in the same, performance verification test for the air separation facility, sequence test for upper/lower stage normal pressure coal hopper purge master in the gasification facility, sequence test for upper/lower stage initial coal loading master in the same, sequence test for char system rock hopper pressure application master in the same, sequence test for gasification furnace light oil leak check master in the same, sequence test for coal rock hopper pressure application master in the same, sequence test for upper/lower coal rock hopper coal reception master in the same, sequence test for slag hopper quenching operation master in the same, and sequence test for gasification steam drum water filling master in the same. (NEDO)

  13. 1998 Annual Study Report. Research and development of solid polymer type fuel cells (Development of techniques for power generation systems and several tens kW class, distributed power source systems); 1998 nendo seika hokokusho. Kotai kobunshigata nenryo denchi no kenkyu kaihatsu (hatsuden system gijutsu no kaihatsu / koden'atsugata su 10kW kyu bunsan dengen system no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The cells are tested using a CO-containing synthetic reforming gas in 1998, to verify the long-term characteristics of the solid polymer type fuel cells. The cells, equipped with the anode catalyst developed therefor, are tested for extended periods, to confirm the performance and stability in the synthetic gas flow. For development of the catalyst, the optimum content of Ru in the Pt and Ru alloy composition is determined. For the cell tests, the single- and 3-cell units are tested for extended periods. For verification of commercial viability of the stacked cell systems, the cell-humidifying techniques are developed, which can uniformly humidify each cell in the stacked unit with a number of cells, after investigating the effects of temporal changes in water permeability, pretreatment conditions and film thickness. These techniques are used to develop and operate a 10kW, stacked cell unit, which successfully generates power of 10.6 kW at the rated current density, exceeding the target of 10 kW. For development of design bases for compact fuel treatment system, the techniques which allow reduction of CO concentration to 10 ppm or less at high repeatability are developed. (NEDO)

  14. Achievement report on research and development in the Sunshine Project in fiscal 1976. Comprehensive discussion on hydrogen utilizing subsystems and researches on peripheral technologies (Research on fuel cell systems); 1976 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Nenryo denchi system kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-03-01

    This paper discusses hydrogen fuel cell systems. In the economic performance of fuel cells, the ratio of fuel cost accounting for in the power generation cost is as very high as 66% or higher to 82%, if hydrogen unit cost is in the range of 20 to 50 yen per Nm{sup 3}. Enhancing the power generation efficiency contributes more greatly to reduction of the power generation cost than by reducing the construction cost. There should be no much influence on the power generation cost if a system lasts four to five years. The paper also discusses the discrete type power generation system. Discussions were given on a waste heat recovering fuel cell system using as the model an office building of 16 stories above the ground, with one basement and a total floor area of 16,000 m{sup 2}. If the system can be constructed in such a way that the fuel cell capacity is made slightly larger than that corresponds to power load, and whole air conditioning load can be taken care only by waste heat by using a heat pump, the auxiliary heat source can be made smaller, and the overall fuel conservation ratio can be larger, thus the fuel was found saved by 40% than in existing systems. In using hydrogen in automobiles, weight problem will emerge if high-pressure hydrogen or metallic hydride is used for hydrogen storage. Liquefied hydrogen is light in weight, but large in volume. Development is desired on high-performance hydrogen absorbing alloys. (NEDO)

  15. 1998 Annual Study Report. Research and development of solid polymer type fuel cells (Development of techniques for power generation systems and several tens kW class, distributed power source systems); 1998 nendo seika hokokusho. Kotai kobunshigata nenryo denchi no kenkyu kaihatsu (hatsuden system gijutsu no kaihatsu / koden'atsugata su 10kW kyu bunsan dengen system no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The cells are tested using a CO-containing synthetic reforming gas in 1998, to verify the long-term characteristics of the solid polymer type fuel cells. The cells, equipped with the anode catalyst developed therefor, are tested for extended periods, to confirm the performance and stability in the synthetic gas flow. For development of the catalyst, the optimum content of Ru in the Pt and Ru alloy composition is determined. For the cell tests, the single- and 3-cell units are tested for extended periods. For verification of commercial viability of the stacked cell systems, the cell-humidifying techniques are developed, which can uniformly humidify each cell in the stacked unit with a number of cells, after investigating the effects of temporal changes in water permeability, pretreatment conditions and film thickness. These techniques are used to develop and operate a 10kW, stacked cell unit, which successfully generates power of 10.6 kW at the rated current density, exceeding the target of 10 kW. For development of design bases for compact fuel treatment system, the techniques which allow reduction of CO concentration to 10 ppm or less at high repeatability are developed. (NEDO)

  16. Fiscal 1997 report on the results of the international standardization R and D. R and D of the standardization of a method to test acceleration life of phosphorous acid fuel cells; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Rinsangata nenryo denchi no kasoku jumyo shiken hoho no hyojunka ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    As for fuel cells, which are expected as a new clean energy, the R and D are being proceeded with in various fields of the world, but the standardization has not been made both in Japan and abroad. In Japan, the situation is that the information on technical terms, indication method, performance test method, and environment/safety test methods of the phosphorous acid fuel cell power generation is publicly spread. In relation to the international promotion of fuel cells to be predicted, it is necessary to internationally standardize cells themselves which are a key component of fuel cell power generation facilities. Phosphorous acid fuel cells are expected of the earliest commercialization of all, but the common test method to evaluate life characteristics of the cell stack has not been established yet. In the R and D, for the purpose of internationally standardizing test methods to evaluate life characteristics of the cell stack, a study on the acceleration life test method of phosphoric acid fuel cells was conducted in terms of the technical trend, data, standard, etc. A plan was prepared on general rules of the method to test acceleration life at the cell reaction part of the small cell, and activities also were started for setting up a technical committee for the fuel cell power system in President`s Advisory Committee on Future Technology. 29 figs., 20 tabs.

  17. Achievement report for fiscal 2000 on the phase II research and development for hydrogen utilizing international clean energy system technology (WE-NET). Task 6. Development of fuel cell of pure hydrogen fueled solid polymer type; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 6. Junsuiso kyokyu kotai kobunshigata nenryo denchi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper describes the achievements in fiscal 2000 from the WE-NET Phase II for research and development Task-6. The objective is to verify performance and reliability, by means of field tests, of a power generation plant using fuel cells of pure hydrogen fueled solid polymer type with power transmission terminal efficiency of 45% and output of 30 kW. The fuel cells were developed by using the cathode humidification process as a humidification method suitable for operation at high utilization rates. With a three-cell stack made by using this humidification process (having an effective area of 289 cm{sup 2}), verification was made on the current density of 0.2A/cm{sup 2}, the characteristics of 0.75V or higher, and the uniform voltage distribution performance being the immediate targets. In order to mitigate the hydrogen utilization in the fuel cells, discussions were given on the serial flow system that divides the laminated cells into two blocks. Thus, operation was found possible with the utilization rate in each block reduced to about 80% by selecting an adequate division rate even if the hydrogen utilization rate is 96% in the entire stack. Stable operation has been performed in the 5-kW class power generation test using the cathode interior humidifying system. Specifications for 30-kW class power plant, system configuration, safety, and material balance were discussed. The basic design was made on the hydrogen gas humidity adjusting system. (NEDO)

  18. Fiscal 1999 phase 2 R and D report of WE-NET (International Clean Energy Network Using Hydrogen Conversion). Task 6. Development of the polymer electrolyte membrane fuel cell supplied with pure hydrogen; 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu seika hokokusho. Task 6. Junsuiso kyokyu kotai kobunshigata nenryo denchi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 research result on development of element technologies for a pure hydrogen fuel cell power system of nearly 45% in efficiency at terminal, and demonstration test result on the 30kW class polymer electrolyte membrane fuel cell system supplied with pure hydrogen. On cell voltage characteristics in high-utilization operation, study was made on degradation and corrosion caused by short supply of hydrogen by using a single cell. As a result, it was found out that reverse polarization of -3.0V has small effect, however, that of -0.7V causes corrosion and deterioration of cell characteristics in a short time. In operation using actual-size cells for the 30kW class plant, it was effective to wet cells on the air side. On hydrogen high-utilization operation technique, study was made on hydrogen recovery and recycle operation, anode outlet line closed operation, and anode recycle operation. In addition, some studies were made on specifications of auxiliary facilities for fuel cells, safety measures for fuel cells and humidity control of supplied hydrogen gas. (NEDO)

  19. Fiscal 2000 achievement report. Development of coal gas production technology for fuel cells (Research using pilot test facility - for public release); 2000 nendo seika hokokusho (Kokai you). Nenryo denchi you sekitan gas seizo gijutsu kaihatsu - Pilot shiken setsubi ni yoru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the development of a coal gasification furnace optimum for fuel cells, research and development was conducted of a coal gas production technology using the oxygen-blown coal gasification technology, and the fiscal 2000 results are put together. In the construction of the pilot test facility, part of the road in the site was constructed as continued from the preceding fiscal year. In the construction of the coal gasification facility, some of the devices were built, which were the coal feeding system, coal gasification furnace, heat recovery boiler, and the char recovery device, and some of the thus-built devices and procured devices were installed. In the study of the control of the operation of the oxygen-blown coal gasification system, the pilot test facility was divided into unit devices and, for each of the unit devices, detailed procedures for pre-start preparation, start, stop, and for the stop of accessorise were deliberated, and important operating steps were worked out. Timing charts were prepared for the operation of each of the facilities during plant start/stop operations. In the effort to deal with serious accidents, special operation procedures were studied and prepared on the case-by-case basis. (NEDO)

  20. Fiscal 2001 achievement report. Development of coal gas production technology for fuel cells - Research using pilot test facility - for public release (Test result report - 2/3); 2001 nendo seika hokokusho (Kokai you). Nenryo denchi you sekitan gas seizo gijutsu kaihatsu - Pilot shiken setsubi ni yoru kenkyu (Shiken kekka hokokusho 2/3)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the development of a coal gasification furnace optimum for fuel cells, a pilot test facility was constructed, and the results of tests and inspections conducted therefor are put together. They include an individual test of the receiving pit hopper vibrator, individual test of the pulverized coal related rotary valve, individual test of the pretreatment compressed air fan, individual test of the coal pulverizer lubricating device, individual test of the coal pulverizer pressure device, individual test of the coal pulverizer, individual test of the coal pulverizer motor, individual test of the coal feeder, individual test of the pulverized coal bunker exhaust fan, individual test of the pulverized coal bunker exhaust fan motor, test of capacity for pulverized coal, individual test of the pulverized coal conveyer blower, test of the sequence of the same, test of pulverizer inert clearing, individual test of the pretreatment condensed water pump in the coal pretreatment device, test of airborne conveyance in the same, verification test of inter-hopper transfer in the same, test of coal pulverization in the same, test operation of the raw material air/low pressure nitrogen compressor in the air separation facility, test operation of the raw material air freezer in the same, and a test operation of the MS adsorber/MS regeneration electric heater. (NEDO)

  1. Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on fuel cell system); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Nenryo denchi system kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1976-03-01

    In fiscal 1974, the domestic and overseas developmental states of fuel cell bodies were surveyed, and some problems on the interconnection between a fuel cell system and power system were studied. Since the maximum outputs of conventional fuel cells are only nearly 10kW, however, those from several hundreds kW to several ten thousands kW are required for buildings or commercial power facilities, in the fiscal 1975, some supposed problems derived from such scale- up of fuel cells were extracted to study their solutions. Study was made on 4 kinds of fuel cells such as alkaline electrolyte, acidic electrolyte, molten salt electrolyte and solid electrolyte fuel cells, and fuel modifier for generating hydrogen. As preliminary modeling work for dynamic performance analysis of fuel cell systems, study was made on scale of the model, DC devices and equipment for customers, environmental impact, power supply reliability, various characteristics and problems in load variation including start and stop, and kinds of accidents and their measures. (NEDO)

  2. Achievement report (edition B) for fiscal 1999 on development of technology to manufacture coal gas for fuel cells. Studies by using pilot test facilities (Volumes for equipment fabrication and constructions, and trial run design); 1999 nendo seika hokokusho (B ban). Nenryo denchi you sekitan gas seizo gijutsu kaihatsu - Pilot setsubi ni yoru kenkyu (kisokoji kiki seisaku hen shiunten sekkei hen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to develop a coal gas manufacturing system for fuel cells, research and development has been performed on a oxygen-blown coal gasifier and researches on a technology to purify gases for fuel cells. This paper summarizes the achievements in fiscal 1999. The current fiscal year has performed, among other the pilot plant construction works, execution of the above-the-ground constructions for the operation center and compressor room building, construction of the cooling water tanks, and partial improvement of roads in the plant site. In the gasifier facilities, items of equipment were fabricated, some of the outsourced articles were procured, and the installations thereof were carried out. For the gas purifying equipment, installation of the gas analyzer room was executed. In the trial run design, discussions were given on the systematic improvements in the test items, the gas sampling procedures, the unit protecting interlock, and the facility protecting logic. For the trial run design, establishment has been implemented on the efficient and functional test plans by establishing priority on the tests to be executed, so that the development items demanded in the pilot test and research can be achieved within the limited test processes. (NEDO)

  3. Achievement report for fiscal 1998. Research and development of polymer electrolyte fuel cell module (Development of 10kW-class transportable power source system of high current density type); 1998 nendo seika hokokusho. Kotai kobunshigata nenryo denchi no kenkyu kaihatsu, kodenryu mitsudogata 10kW kyu kahangata dengen system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the development by the end of fiscal 2000 the above-named system which will operate on methanol/air (normal atmospheric pressure) yielding 0.3W/cm{sup 2} or more, efforts are exerted about a high-lamination type PEFC (polymer electrolyte fuel cell) module and a lamination type methanol reformer, this project carried over from fiscal 1997. In relation with the PEFC module, platinum loading was reduced (by 60% from the amount in fiscal 1997) by catalytic layer improvement, cell characteristics were improved, continuous load imposition was performed using a reformed simulation gas, life test was conducted consisting of frequent starts and stops, lamination was built using shaping separators, and a 2kW-class stack was built and evaluated for performance. Next to come is a test run of a 5kW-class stack. In relation with the lamination type methanol, element components were tested. A reformer section and a catalytic combustion section were designed, manufactured, and tested, and a vaporizer section and a CO reduction section were evaluated for performance and life. A 2kW-rate lamination type methanol reformer was designed and built by integrating the said element components, and was subjected to a test run for performance evaluation. (NEDO)

  4. FY 1999 Results of research and development project for polymer electrolyte fuel cells (PEFCs). Development of high current density type 10kW class portable power source systems; 1999 nendo kotai kobunshigata nenryo denchi no kenkyu kaihatsu seika hokokusho. Kodenryu mitsudogata 10kW kyu kahangata dengen system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Described herein are the FY 1999 results of the research and development project aimed at development of multi-stacked PEFC modules and plate-stack type methanol reformers, and researches on portable power source systems, for development of methanol-air 10kW class (over 0.3W/cm{sup 2}) PEFC systems for portable use by the end of the FY 2000. The programs for the multi-stacked PEFC modules include improvement of tolerance against CO by improvement of catalyst bed and gas passage structures; development of a multi-stacked 5kW class stack structured to prevent fuel starvation; endurance tests conducted at a constant load using a simulated methanol reformate gas; and development, on a trial basis, of the stack using a formed separator. The programs for the plate-stack type methanol reformers include development, on a trial basis, of reforming catalysts integrated with flow passages, combustion catalysts and CO oxidation catalysts, and endurance evaluation tests for the reformer elements. The researches on portable power source systems include studies on, e.g., system control/behavior and efficiency, and basic system designs. The performance and environment endurance tests are also conducted for auxiliary equipment, e.g., blowers. (NEDO)

  5. Fiscal 2001 achievement report. Development of coal gas production technology for fuel cells - Research using pilot test facility - for public release (Part 1 - Construction and test operation); 2001 nendo seika hokokusho (Kokai you). Nenryo denchi you sekitan gas seizo gijutsu kaihatsu - Pilot shiken setsubi ni yoru kenkyu (Sono 1 - Koji shiken unten hen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the development of a coal gasification furnace optimum for fuel cells, research and development was conducted of a coal gas production technology using the oxygen-blown coal gasification technology, and the fiscal 2001 results are put together. In the construction of the pilot test facility, work involved the road in the site, road illumination system installation in the site, and an unauthorized entry prevention system. In the construction of the coal gasification facility, work involved electrical instrumentation and painting for the coal feeding system, coal gasification furnace, heat recovery boiler, and so forth, and the installation of a series of devices was completed. In July following the completion, power was received and test operations were started, which included the operation of the coal gasification facility alone. Renting was started in August for the coal pretreatment facility, air separation facility, and the slag treatment device. In the study of the operation control technology for the oxygen-blown coal gasification furnace system, test operations were conducted based on the operating procedures prepared in the preceding fiscal year, which included a test operation performed for the pilot test facility alone. Parameters for equipment control obtained through the test operations, and improvements on operating steps carried out as required, were all reflected on the operating procedures. (NEDO)

  6. Solar cell. Taiyo denchi

    Energy Technology Data Exchange (ETDEWEB)

    Kamihara, T; Kondo, S; Mori, K [Matsushita Electric Industrial Co. Ltd., Osaka (Japan)

    1990-10-23

    This invention provides a solar cell having high resistance to strong incident light and high temperature preservability. Reason of performance degradation of the solar cell in high temperature atmosphere thermally diffuses at the boundary surface of the silicon with metal particles. The method of blocking this thermal diffusion is that the film thickness is of the level that the electrons can pass through the film by a quantum dynamical tunnel effect. In this invention, the construction is that a transparent substrate, a transparent electrode, a P-type amorphous silicon, an I-type amorphous silicon, silica and a collector electrode are sequentially laminated and receives the incident light, thus generating a voltage between the two electrodes. Thickness of silica film is 10-100 microns. Materials of the collector electrode are either single element or alloys of Cs, K, Na, Li, Ba, Mg, Cd, Ta, Al, Mo, Zr, Co, Fe, Cu, Ag, W, Cr, Au and Ni. 13 figs., 1 tab.

  7. Solar cell. Taiyo denchi

    Energy Technology Data Exchange (ETDEWEB)

    Amemiya, S.; Hashimoto, Y. (Canon Inc., Tokyo (Japan))

    1991-05-17

    This invention provides a cheap solar cell having a transparent surface protective layer which satisfies both controversial properties such as high electroconductivity and high water repellency and also abated the reduction of photoelectric conversion. In other words, this invention provides a solar cell having a surface-protective layer prepared by lamination of a mixture of a transparent water-repelling resin and a transparent electroconductive oxide powder; said protective layer is grounded at the surface resistance of 1 {times} 10 {sup 10} ohm or less and the contact angle of water on said protective layer is 90 degrees or more. The transparent water-repelling resin used is a fliorine resin such as PTFE and a silicone resin such as organopolysiloxane. The transparent electrodonductive oxide powder used is tin oxide, indium oxide or a complex compound of ton oxide and antimony oxide. The solar cell of this invention can be used for a long time because the adhesion of the dusts and the contamination by dirty water are restricted. 1 fig., 1 tab.

  8. FY 2001 report on the results of the survey of the formation promotion subsidy project on the environmentally friendly type energy community. Survey of the commercialization of high efficiency power generation using fuel of waste such as waste construction materials; 2001 nendo kankyo chowa gata energy komyuniti keisei sokushin hojo jigyo. Kensetsu haizai tou haikibutsu nenryo ni yoru kokoritsu hatsuden no jigyosei chosa chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    The paper studied a system for power generation and heat utilization using wood chips such as waste construction materials, used paper inappropriate for recycling and plastic refuse from neighboring local governments as fuel and assessed a potentiality of the commercialization. As to the system, the following were conducted: selection of the optimum combustor in the waste power generation, survey of the state of corrosion of boiler tube in the steam conditions and waste properties, selection of the optimum quality of boiler materials, etc. In the assessment of a potentiality of the commercialization, the commercialization was studied as in-house power generation/heat utilization business with a power generation scale of 9,950kW and a steam supply scale of 31.5t/h. As a result of the study, the energy conservation effect was found to be expected as follows: reduction of 33,000kL/y crude oil equivalent and reduction of 16,000t-CO2/y emission. As a result of studying the economical efficiency of business, the unit price of wood chip purchase and the unit price of waste plastic treatment which are required to recover the difference of the initial investment within 5 years were greatly different from the level as an aim. For the realization as business, a subsidy of 15% and more cost reduction were requested. (NEDO)

  9. FY 2001 report on the survey of the formation promotion subsidy project on the environmentally friendly type energy community. Potential survey of the introduction of a processing/power generation system using ASR in the South region of Tochigi Prefecture; 2001 nendo kankyo chowa gata energy komyuniti keisei sokushin hojo jigyo. Tochigi ken nanbu chiiki ni okeru ASR (Shuredda dust) wo nenryo to shita shori hatsuden system no donyu kanosei chosa chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the consistent processing of waste automobile in Tochigi Prefecture and the neighboring area, survey/study were made of the thermal recycle using shredder dust, ASR (automobile shredder residue), as fuel as well as the material recycle. As to the amount of material recycle of waste automobile, the amount of potential recycle of iron, copper, plastic, etc. was estimated, and it was found out that the potential recycle of parts such as engine was 40-45%, that of iron scrap 35-40%, and that of ASR 20-25%. The amount of fuel (ASR amount) to be thrown into the gasification power generation system was set up at 150t. As the gasification power generation system, the pyrolysis gasifier and shaft kiln gasification melting furnace were selected. In the study of economical efficiency of the gasification power generation system, the following were considered: ASR processing price, plant cost, subsidy, running cost, char receiving price, power selling price, etc., but even in the case of the pyrolysis gasifier with highest valuation, both payback years and IRR did not reach the target. (NEDO)

  10. Report on the results of the FY 1999 R and D of polymer electrolyte fuel cells. Development of the power system technology (Development of high voltage several 10 kW class dispersed generation system); 1999 nendo kotai kobunshigata nenryo denchi no kenkyu kaihatsu seika hokokusho. Hatsuden system gijutsu no kaihatsu (koden'atsugata suju kW kyu bunsan dengen system no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper described the results of the FY 1999 development of polymer electrolyte fuel cell and several 10 kW class dispersed generation system. The humidification of the cell body is the internal humidification method in which water is directly supplied to cell, which makes the cell life long. The cooling using latent heat of vaporization of the water supplied makes the temperature distribution inside the cell face homogeneous. In the test for long life, the system was stably operated at voltage lowering speed of 11mV/1000h. The optimization of water supply structure in the stack increases the latent heat cooling amount and makes the temperature distribution inside the cell face homogeneous. The reduction of CO concentration in reformed gas is extremely important for improvement of cell performance and long-term stabilization of cell voltage. By the two-stage structure selective oxidation device, the CO concentration at inlet, 5,000 ppm, can be reduced to below 10 ppm at outlet. In the demonstrative experiment on the several 10 kW class dispersed generation system, efforts for reduction in size of structural equipment and package were made, and a possible size of 200*150*180cm was obtained. Based on the chart of 30kW class system flow, the heat material balance was analyzed, and the power generation efficiency of 40% at a.c. sending end and overall efficiency of 80% were confirmed. (NEDO)

  11. FY 1999 Report on results of development of high-efficiency energy system technologies for transportation and domestic use. R and D of polymer electrolyte fuel cells, power system technologies, and several kW class domestic power systems operating at normal pressure; 1999 nendo un'yu minseiyo kokoritsu energy system gijutsu kaihatsu, kotai kobunshigata nenryo denchi no kenkyu kaihatsu, hatsuden system gijutsu kaihatsu, joatsu sadogata su kW kyu kateiyo dengen system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Described herein are the FY 1999 results of the research and development project aimed at development of fuel cell systems for power source systems suitable for domestic use. The programs for development of fuel cell body include improvement of the anode forming method for increasing its CO tolerance, enhancing cell performance at 0.5mg-metal/cm{sup 2} as the catalyst quantity to a level almost comparable to that obtainable at 0.9mg-metal/cm{sup 2}. The programs for development of the fuel supply system include studies on endurance of the elements, e.g., starting-up/shutting-down of the Ru/Al{sub 2}O{sub 3} catalyst, using a microreactor, confirming that it is serviceable for at least 1,000 hours. The natural gas reformer is developed and operated, on a trial basis, achieving stable supply of steam and fuel, and thermal efficiency of 82.7%. The operation researches include development and operation of a 1kW class module, achieving the performance surpassing the FY 1999 targets (average cell voltage: 0.70V, output: 1.27kW) with a simulated reformate gas at an air utilization rate of 20% and current density of 0.3A/cm{sup 2}. (NEDO)

  12. FY 2000 research cooperation project on the research cooperation for the commercialization of the regional adaptation type photovoltaic power generation system, etc. Research cooperation for the commercialization of the methane fermentation gas fuel cell power generation system; 2000 nendo kenkyu kyoryoku jigyo. Chiiki tekigogata taiyoko hatsuden system to no jitsuyoka ni kansuru kenkyu kyoryoku (Metan hakko gas nenryo denchi hatsuden system no jitsuyoka ni kansuru kenkyu kyoryoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research cooperation for the commercialization of methane fermentation gas fuel cell power generation system was made in a stock farm in Guangzhou city, China, and the FY 2000 results were summed up. In the project, the methane fermentation gas is recovered from animal faces, and a power generation system by fuel cell using the gas as fuel is constructed, and at the same time the waste is made compost and used as manure. In this fiscal year, the starting ceremony was made at the stock farm in Guangzhou city in June, and the main body of fuel cells was carried in and assembled. The trial operation of the system was successfully made in March 2001. At the same time, survey of the waste water from the farm and methane fermentation was made with accuracy. Survey was further made of the actual state of the recent energy supply/demand and the present situation of renewable energy as measures taken for non-electrification areas and environmental problems. As a result, the importance of further cooperation with the China side was emphasized in terms of the securing of animals/faces, optimum methane fermentation/recovery from animal faces, optimization of electric power of the area and environmental response, etc. (NEDO)

  13. Report of the FY 1995 research cooperation promotion projects (overall evaluation). Research cooperation in fuel cell utilization/district power generation system and village type technique for simplified continuous production of raw palm oil; 1995 nendo kenkyu kyoryoku suishin jigyo (sogo hyoka) hokokusho. Nenryo denchi katsuyo chiiki hatsuden system ni kansuru kenkyu kyoryoku / sonrakugata kan'i renzoku palm arayu seizo gijutsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The research cooperation project for fuel cell utilization/district power generation system is conducted under the research cooperation agreement between NEDO and Electricity Generating Authority of Thailand (EGAT), to demonstrate a 50 kW pilot plant constructed at EGAT's Bang Pakong power station. The fuel cell reforms self-spouted natural gas into H{sub 2} as the fuel. It has produced a total power of 341,921 kWh under the conditions of cumulative operating time: 8,115.4 hours, longest continuous operating time: 1,100 hours, service factor: 89.64%, load ratio: 86.13% and system utilization factor: 77.20%. The fuel technique will be acceptable for Thailand, if it is economically competitive. The project for producing raw palm oil is for Malaysia. The facilities introduced and tested for the new process are a continuous steam-heated fruit remover, fiber/nut separator, and shell cutter. The new process is evaluated to produce higher-quality raw palm oil in higher yield while consuming less energy. The new process, whose steps are automated, saves operating cost, and suitable for Malaysia which is suffering shortage of manpower. (NEDO)

  14. Research report for fiscal 1998. Development of advanced surface processing technology for methane-fueled aircraft engine members (Laser-aided advanced processing system technology); 1998 nendo chosa hokokusho. Methane nenryo kokukiyo engine buzai no kodo hyomen kako gijutsu kaihatsu (Laser oyo senshin kako system gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the research and development of erosion-resistant abradable materials for the methane-fueled aircraft engine front section, a laser-aided surface reform technology was developed for Ti alloys and the like. In relation with the article 'Intermetallic Compound Coating Formation Technology,' an NiTi sprayed coating containing excess Ni solid solution was found to be quite high in resistance to erosion, and similar to Ti-6Al-4V in resistance to oxidation at 300 degrees C. Furthermore, an MCrAlY erosion-resistant coating was formed capable of resisting oxidation at temperatures higher than 1000 degrees C. In relation with the article 'Spraying Phenomenon Evaluation Technology,' studies were made of combustion synthesis reaction during plasma spraying and of the prediction of flight trajectories of different powders, for which optical fiber dichroic temperature measuring, 2-dimensional imaging, and LDV (laser Doppler velocimetry) were applied in combination. Concerning the spraying of intermetallic compound coatings, a temperature rise occurred when heating by laser was performed simultaneously with the laser-induced combustion synthesis reaction. In relation with the article 'Technology of Multiple Spraying on Curved Substrate,' it was found that the gas cooled method works effectively when spraying an erosion-resistant coating onto a thin Ti alloy made turbine blade. (NEDO)

  15. FY 1991 report on the results of the demonstration test on the methanol conversion at oil-fired power plant. Feasibility study of a new system for the stabilized supply of fuel use methanol; 1991 nendo sekiyu karyoku hatsudensho metanoru tenkan tou jissho shiken. Nenryo you metanoru kyokyu antei ka no tameno shin system no kanosei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    As a part of the project on the demonstration test on the methanol conversion at oil-fired power plant, feasibility study was made of a new system for methanol production by using abundant hydraulic power energy overseas and by combining water electrolysis and coal gasification technology, and the FY 1991 results were summarized. As a result of the survey, the following were selected as water electrolysis facilities: high efficiency/high current density/simplification system and solid polyelectrolyte electrolysis system with a high purity of hydrogen gas. As the coal gasifier, the oxygen blown furnace was selected which has a high carbon utilization factor, is able to gasify coal at high pressure, has no unnecessary N{sub 2}, and is being used in the integrated coal gasification combined cycle power system. As methanol synthesis facilities, the MGC/MHI method super converter was selected. Assuming the output of hydroelectric power generation to be 4,000MW, conceptual design of the optimum system was made. The methanol cost was estimated under the conditions written below: cost of hydroelectric power generation at site: 2-5 yen/kWh, coal unit price at site: 5,000-6,000 yen/t, transportation distance: 5,000-10,000 km. (NEDO)

  16. FY 1992 report on the results of the demonstration test on the methanol conversion at oil-fired power plant. Feasibility study of a new system for the stabilized supply of fuel use methanol; 1992 nendo sekiyu karyoku hatsudensho metanoru tenkan tou jissho shiken. Nenryo you metanoru kyokyu antei ka no tameno shin system no kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    An investigational study was made of potentiality of a new system for methanol production by using abundant hydraulic power energy overseas and by combining water electrolysis and coal gasification technology, and the FY 1992 results were summarized. In this fiscal year, survey was made of the potential water power and coal in Malaysia, Canada and Brazil, and case study was also made. As a result of the study, the cost of methanol was 7.1 yen/10{sup 3}kcal in case of Malaysia, 8.6 yen/10{sup 3}kcal in case of Canada and 8.9 yen/10{sup 3}kcal in case of Brazil. It was found out that the cost was economically less advantageous as compared with the present methanol price of 3.0-5.5 yen/10{sup 3}kcal. In a comparison between the existing coal/oil/LNG thermal power generation and this system from viewpoints of the energy balance/CO2 emission amount, the energy balance of this system is worse than those of the above-mentioned power generation when adding the coal thrown, but the CO2 emission amount of the system was less than those of coal/oil thermal power generation. In conclusion, this system seems to be an effective means in the light of the promotion of development of the undeveloped hydraulic power, effective utilization of renewable energy and global environmental preservation. (NEDO)

  17. Research report for fiscal 1998. Basic research for promoting joint implementation, etc. (fuel change plan for No. 1 and No. 9 Irkutsk Heat and Power Co-Generation Plants, Irkutsk, Russia); 1998 nendo chosa hokokusho. Roshia renpo Irkuktsk shu dai 1 go oyobi dai 9 go Irkutsk netsu heikyu hatsudensho nenryo tenkan keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A research is conducted to find out if efficiency will increase and greenhouse gas will decrease when fuel is changed from coal to gas at the above-named plants, and the economics of the plan is reviewed. The No. 1 plant comprises 18 coal-fired boilers with a total design capacity of 2985 tons/hour, and 8 steam turbine generators rated at 185MW, constructed in the 1940s. The No. 9 plant was constructed in the 1960s and 1970s. Four different modifications programs are drafted to study the fuel change plan. As the result, it is found that the addition of natural gas burning facilities to the existing heat and power co-generation plants and the modification of the existing boiler-related facilities will be low in earning rate and reliability, though excellent in budget size and cost efficiency; and that to dismantle the existing plants and to newly construct heat and power plants operating on gas turbines will bring about a higher earning rate, fuel cost reduction effect, and reliability, though such will cost more. (NEDO)

  18. New Sunshine Program for fiscal 2000. Development of photovoltaic power system commercialization technology (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Surveys and studies of peripheral key technologies/Surveys of environmentally-friendliness enhancement for next-generation solar cell development); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (Shuhen yoso gijutsu ni kansuru kenkyu chosa, Jisedai taiyodenchi kaihatsu kankyo tekioka chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Though the trends of solar cell development are becoming increasingly diverse across the world, yet none has emerged to promise a stable solar cell supply in the future. Under the circumstances, studies were conducted to clarify strategies for solar cell technology development which would be well adapted to Japan's social environments, with the trends of development in the United States and European countries taken into consideration. The surveys covered the research and development and diffusion of photovoltaic power generation in the United States and European countries, and their solar cell research and development strategies and trends of development were put together. Surveys were also conducted into the research and development of unconventional types of solar cells, such as the dye-sensitized solar cell, organic solar cell, conjugate polymer solar cell, and the polymer/C{sub 60} based solar cell, and into the status of resources of materials for solar cells such as gallium, arsenic, cadmium, tellurium, indium, selenium, and germanium. Regarding the future of photovoltaic power generation research and development, it was concluded that commercialization technology development and basic research and development should continue. Also pointed out was the importance of the enlargement of the market for photovoltaic power generation systems. (NEDO)

  19. New Sunshine Program for fiscal 2000. Development of photovoltaic power system commercialization technology (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Surveys and studies of peripheral key technologies/Surveys of environmentally-friendliness enhancement for next-generation solar cell development); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (Shuhen yoso gijutsu ni kansuru kenkyu chosa, Jisedai taiyodenchi kaihatsu kankyo tekioka chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Though the trends of solar cell development are becoming increasingly diverse across the world, yet none has emerged to promise a stable solar cell supply in the future. Under the circumstances, studies were conducted to clarify strategies for solar cell technology development which would be well adapted to Japan's social environments, with the trends of development in the United States and European countries taken into consideration. The surveys covered the research and development and diffusion of photovoltaic power generation in the United States and European countries, and their solar cell research and development strategies and trends of development were put together. Surveys were also conducted into the research and development of unconventional types of solar cells, such as the dye-sensitized solar cell, organic solar cell, conjugate polymer solar cell, and the polymer/C{sub 60} based solar cell, and into the status of resources of materials for solar cells such as gallium, arsenic, cadmium, tellurium, indium, selenium, and germanium. Regarding the future of photovoltaic power generation research and development, it was concluded that commercialization technology development and basic research and development should continue. Also pointed out was the importance of the enlargement of the market for photovoltaic power generation systems. (NEDO)

  20. New Sunshine Program for fiscal 2000. Development of photovoltaic power system commercialization technology (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Survey and research of analysis of commercialization - Separate Volume: Survey of next-generation ultrahigh-efficiency solar cell system); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (Jitsuyoka kaiseki ni kansuru chosa kenkyu - Bessatsu : Jisedai chokokoritsu taiyodenchi system ni kansuru chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the preparation of a proposition concerning future research and development, surveys and studies were conducted centering about efficiency enhancement and cost reduction for the next generation ultrahigh-efficiency solar cell system. For improving the efficiency of the crystalline compound solar cell, studies were made about the prospects of the embodiment of a 3-junction and 4-junction types and of an increase in conversion efficiency expected to realize thanks to their light condensation behavior. It was inferred that anticipation of 29-47% conversion efficiency in 1 to 4-joint cells was theoretically acceptable. Four-joint structure cell fabrication would be a challenging task but would bring about an conversion efficiency of approximately 47% thanks to enhanced light condensation capability. As for cost reduction through the use of light condensation technology, surveys of overseas trends showed that the condensation-enhanced photovoltaic power system was characteristically fit for lower-price production. As for condensation and tracking systems, studies were made about cost calculation models of organizations involved in the United States and Europe, and then it was found that cost reduction in the optical system for condensation and in the tracking mechanism would be mandatory for the achievement of 75 yen/W. (NEDO)

  1. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Research and development of photovoltaic system evaluation technology (Research, development, and survey of crystalline solar cell evaluation system); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (kesshokei taiyo denchi hyoka system no kenkyu kaihatsu chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In the basic study of ultrahigh-efficiency cells, the technology of ribbon crystal growing is again attracting attention for shortage of Si material supply. The new technology and problems to solve for cost reduction for it are discussed. Concerning the bulk type crystalline Si which is a core material, recent trends are mentioned involving studies of basic substrate properties such as the photoabsorption coefficient and crystal defects for achieving higher efficiency, development of gettering and surface passivation technologies, enhancement of processing speeds, radiation concentration behavior, etc. Newly obtained findings about photodegradation are mentioned, and some remedial measures are described. Recent reports on the application of porous Si to solar cells are compiled. In connection with the development of low-cost quantity-production process technologies, a remarkable progress recently marked by polycrystalline Si solar cells is described. Furthermore, it is stated that new process technologies will be required in the fields of material refining, substrate manufacturing, and cell fabrication. A proposition is presented aiming at developing cell modules compatible with application systems and practicalizing modules that may be integrated with roofing materials. Reference is also made to surveys overseas. (NEDO)

  2. Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system (development of technology to manufacture thin film solar cells (surveys and researches on analyzing practical application )). Volume 1; 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    It is intended to identify and analyze quickly and accurately the technological trends inside and outside the country on thin film solar cells, to reflect the results effectively on research and development of practical application of the thin film solar cells for power use, and to aid the research on practical application of the technology to manufacture the thin film solar cells. This fiscal year introduced the new project of researching and developing the poly-crystal silicon-based thin film solar cells. Discussions were given on designing the solar cells, including setting of thickness of an active layer required to improve efficiency of the silicon-based thin film solar cells, the light confining technology, and surface passivation. Comparisons and discussions were given on the new amorphous/poly-crystal silicon thin film manufacturing method and the conventional plasma CVD process. A research development program was introduced for a super laboratory to aid establishing the practical application technology for the silicon-based thin film solar cells. Chalcopyrite compounds including CuInSe2, and CdTe have not shown deterioration even in a long-term outdoor exposure test, hence they are noted as materials for high-efficiency solar cells and studied actively. Although still small in area, the net conversion efficiency was found in the order of 17%. Technological development has started to search mass production processes and commercialization possibility in the future. (NEDO)

  3. Development in fiscal 1998 of silicon manufacturing process to rationalize energy usage. Surveys and researches on analysis of practical application of technology to manufacture silicon raw materials for solar cells; 1998 nendo energy shiyo gorika silicon seizo process kaihatsu seika hokokusho. Taiyo denchi silicon genryo seizo gijutsu no jitsuyoka kaiseki ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With an objective to develop a mass production technology to manufacture silicon raw materials for solar cells, and assist its practical application, surveys and analyses were performed on trends in development of the related technologies, the problems therein , market trends and industrial trends thereof. This paper summarizes the achievements in fiscal 1998. The worldwide production amount of solar cells in 1998 is estimated to have achieved 150 MW, and the silicon consumption reached the level of 2,300 tons. In spite of the economic recession environment, there was no change in the expansion trend. In developing an SOG-Si mass production and manufacturing technology, construction of pilot plants for each process has been completed, and entered into the operation research phase. In developing a technology to manufacture high quality poly-crystalline silicon substrates, fabrication has been completed on the on-line ingot cutting equipment and the plasma heating equipment, and the stage is now in operation research of continuous electromagnetic casting process. The conversion efficiency of the poly-crystalline silicon solar cells is 14 to 16% at the mass production level, whose enhancement requires indispensably the improvement in quality of the substrate. Discussions are required on the ingot manufacturing conditions in coordination with improvement in the cell manufacturing technology. (NEDO)

  4. Achievement report for fiscal 1997 on developing a silicon manufacturing process with reduced energy consumption. Investigation and research on analyzing practical application of a technology to manufacture solar cell silicon raw materials; 1997 nendo energy shiyo gorika silicon seizo process kaihatsu. Taiyo denchi silicon genryo seizo gijutsu no jitsuyoka kaiseki ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes the achievement in fiscal 1997 of analyzing practical application of a technology to manufacture solar cell silicon raw materials. Silicon consumption for solar cells in fiscal 1997 has increased to 2000-ton level, and the supply has been very tight. For drastic improvement in the demand and supply situation, development of SOG-Si manufacturing technology and its early practical application are desired. The development of the NEDO mass-production technology using melting and refining has completed constructing the process facilities in fiscal 1998, and will enter the stage of operational research. However, insufficiency in the basic data about behavior of impurities is inhibiting the development. In the substrate manufacturing technology, discussions have shown progress on use of diversifying silicons outside the standard by using the electromagnetic casting process. For slicing and processing the substrates, development of a high-performance slicing equipment and automatic rough rinsing machine is under way. Properties required on silicon raw materials vary considerably widely because of difference in cell making systems and conditions, which is attributable to unknown impurity behavior. When 1GW production is assumed, the cell module manufacturing cost is calculated as 137 yen/W, for which low-cost mass production for its realization, slicing productivity enhancement, and cost reduction are required. The paper also describes site surveys in overseas countries. (NEDO)

  5. Research and development of system to utilize photovoltaic energy. Survey on the high-durability and low-cost materials for constructing the solar-cell module and its structure; Taiyoko hatsuden riyo system no kenkyu. Taiyo denchi module yo kotaikyusei tei cost zairyo, kozo ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the results obtained during fiscal 1994 on a survey on the high-durability and low-cost materials for constructing the solar-cell module and on its structure. With respect to forms and materials used in the present solar-cell modules, identification was made on the current status of products commercially available and developed inside and outside Japan. Main types of solar cells used for electric power are of crystal-based silicon. Amorphous silicon and CdS-CdTe are used for consumer applications of indoor and outdoor use. As regards transparent resin materials, fluorine resin, PET, acryl, and polyimide are used as surface materials, and EVA, silicon and PVB are often used as fillers. Developments inside and outside Japan are limited to systems of polycarbonate, methacryl, fluorine, polyurethane, acryl and polyester. Butyl rubber and polyurethane are used as sealing materials. Developments are being performed on silicon rubber, polychloroprene rubber and EPT rubber for shaped materials, and silicon systems, urethane systems and polysulfide systems for non-shaped materials. 3 figs., 8 tabs.

  6. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology (Survey and research on practical application - Volume 1); 1999 nendo taiyoko hatsauden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu - 1)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A 'Sub-committee for investigation of crystalline compound semiconductor solar cells' was established with the participation of experts from the industrial, bureaucratic, and academic circles to support the manufacture of ultrahigh-efficiency crystalline compound solar cells, and a survey was conducted about technical trends relating to III-V group compound solar cells. In the study of the trends and tasks of the state of the art technology, it is stated that the III-V group compound semiconductor multi-junction solar cell was steadily improving in efficiency, that the InGaP/GaAs 2-junction cell on a Ge substrate and InGaP/GaAs/Ge 3-junction cell in particular were moving toward mass production, and that the target for the 4-junction cell to achieve was 40% or higher in efficiency. For cost reduction, investigations were made into the heteroepitaxial technology, dimensional enlargement, mass production, raw material cost reduction, feasibility of the polycrystalline thin-film technology, light concentration, etc. For efficiency improvement, boundary layer control, structure designs, etc., were studied. Investigations were also conducted into nitride semiconductors, superlattice construction, etc., which related to new materials for thin films. TPV (thermophotovoltaic) power, etc., were reviewed for their practical application. (NEDO)

  7. Achievement report for fiscal 1999 on the development of silicon manufacturing process rationalizing energy utilization. Research and study on analysis to put silicon raw material manufacturing technology for solar cells into practical use; 1999 nendo energy shiyo gorika silicon seizo process kaihatsu seika hokokusho. Taiyo denchi silicon genryo seizo gijutsu no jitsuyoka kaiseki ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In order to support the development and practical application of a mass production technology for manufacturing silicon raw materials for solar cells, research and study were performed on trends of developing the related technologies, and movements in markets and industries. This paper reports the achievements thereof in fiscal 1999. Markets for solar cells are growing favorably, and the worldwide solar cell production in 1999 was 200 MWp, of which 80% or more is occupied by crystalline silicon solar cell. While development of the manufacturing technology for SOG-Si mass-production is in the stage of operation research of pilot plants, it has been verified that problems of impurity contamination was resolved, and high-purity silicon can be manufactured. In developing the silicon scrap utilization technology and a technology to integrate silicon refinement with casting, a conversion efficiency of 14% or higher was acquired in prototype sample substrates. It has been verified that a variety of raw materials can be dealt with by using the above technology, which has a possibility of cost reduction. In developing a substrate manufacturing technology, a great progress has been made in enhancing the productivity and reducing the cost by developing the continuous casting in the electromagnetic casting and the automation technology. (NEDO)

  8. Fiscal 2000 project of inviting proposals for international joint research - invitation for international proposal (Power generation No.14). Achievement report on joint research for utilizing Russia's now-unused high-viscosity crude oil as fuel for power generation; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (hatsuden No.14). Russia miriyo konensei gen'yu no denryoku nenryo riyo kyodo kenkyu chosa seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The Russkoye high-viscosity oil field is located in the western part of Siberia, Russia. Joint research is under way to develop a technology for reducing the viscosity for the collection of crude oil through the utilization of a gas condensate discharged by a neighboring gas field. This report comprises eight chapters, namely, (1) the background, purpose, and contents of the research, (2) Russia's oil resources and oil industry, (3) high-viscosity oil fields in Russia, (4) analysis of Russkoye crude oil and gas condensates yielded in Russia, (5) methods for viscosity reduction, (6) evaluation of combustibility, (7) scenario for developing the Russkoye oil field, and (8) research results as summarized and future tasks. Studied in chapter (5) are approaches to viscosity reduction, methods for emulsification, and a method for viscosity reduction by use of a gas condensate. These are tested and the results after analysis clearly show that the Russkoye crude oil, when blended with a gas condensate, will turn transportable and will provide a fuel equivalent to fuel oil C. (NEDO)

  9. FY 2001 report on the results of the survey of the environmentally friendly type energy community project. Utilization of combustible waste as solid fuel in Shimizu City, Shizuoka Prefecture, and the wide spread sphere of municipalities (Facilities such as RDF+LNG combined use high efficiency waste power generation); 2001 nendo Shizuoka ken shimizu shi oyobi koiki shichoson ken ni okeru kanensei haikibutsu kokeika nenryo riyo kankyo chowa gata energy komyuniti keisei sokushin hojo jigyo chosa (RDF+LNG heiyo kokoritsu haikibutsu hatsuden tou shisetsu) chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    Survey/study were conducted of viability of an idea of the high efficiency power generation that combinedly use RDF from the refuse generated in Shizuoka/Yamanashi/Nagano prefectures and LNG from the LNG base in Shimizu City, Shizuoka Prefecture. In the survey of raw materials for RDF, the present amount that can be supplied to RDF power generation was estimated at 280 t/d in RDF and 4,300 Kcal/kg or more in heating value. As to the RDF/LNG combination power generation, combinations of RDF200t/d + 25MW (capacity of gas turbine power generation) or RDF200t/d + 70MW seem to be appropriate. And, 30% or more of RDF power generation efficiency is made possible. In the study of economical efficiency, expenses born by local governments were calculated supposing that the difference between the unit price of power selling and that of power generation in power generation is born by RDF suppliers. As a result, the share becomes approximately 8,600-12,000 yen/refuse t in 15-year operation, and was found lower than that in the existing small-/medium-scale refuse incineration treatment. The combustion flue gas associated with the power generation business becomes approximately 300,000 Nm{sup 3}/h. The gas turbine fuel is natural gas, and RDF is good in combustibility. Therefore, the effect on the environment is expected to be small. (NEDO)

  10. Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Development of solar beam power generation and utilization systems and ancillary technologies (Research and development of new building material integrated solar cell modules - investigation and research on analysis of practical application); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In order to promote the research to put new building material integrated solar cell modules into practical use, the following items were investigated: (1) functions and specifications for harmonizing with buildings, (2) new module materials that can respond to building materials, (3) marketability, (4) standardization of the assessment methods, (5) consistency with relevant legislation and related institutions, (6) effects on environment as building materials, and (7) investigation on technological trends inside and outside the country. In Item (1), the significance of developing the new building material integrated solar cell modules was made clear. In Item (2), the performance requirements on the currently used module materials were put into order. In Item (3), the market size was investigated, and assignments to establishing the market were put into order, such as the distribution and construction institutions, and assistance to the system introduction. In Item (4), standardization and unification of the assessment methods were discussed, and the items to be standardized were extracted. In Item (6), LCA on the currently used modules was performed. In Item (7), participation was made to the second solar beam power generation conference and EUROSUN '98; investigations were made on trends of developing the new building material integrated solar cell modules and how the recycling related legislation is being progressed; and the achievements in the development activities were confirmed, and the assignments were investigated at the new building material integrated solar cell module subcommittee. (NEDO)

  11. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power utilizing system and peripheral technologies (Research and development for enhancing reliability of photovoltaic power generation - Research on environmental measures for compound solar cell modules); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (taiyoko hatsuden no shinraisei kojo ni kansuru kenkyu kaihatsu - kagobutsu taiyo denchi module no kankyo taisaku no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research is conducted to properly deal with environmental problems, such as compromised solar cell safety, which may follow the mass introduction and diffusion of photovoltaic power systems. In the research of fiscal 1999 on technical literature on environmental measures against lead and animal tests, a need was found to reduce lead in power systems and to grasp lead elution characteristics for the establishment of environmental measures. In a safety test conducted for thin-film CIS (copper indium diselenide) based solar cells, basic data were collected about the vaporization rate of Se, the effect of moisture on the Se vaporization rate, etc. Basic data were also collected about the relationship between the combustion temperature and the amount of scattered lead in particular from the solder used as the conducting material in silicon based solar cells. In the evaluation of the environmental impact of thin-film CIS solar cells in case of fire, it was found that Se concentration below 10-20m in the plume was near the permissible concentration of 0.1mg/m{sup 3} as recommended by Japan Society for Occupational Health and that the concentration levels predicted for the periphery were two orders of magnitude smaller than the mandatory level. (NEDO)

  12. Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Volume 1. Development of thin film solar cell manufacturing technologies (Development of technologies to manufacture low-cost large-area modules and survey and research on analyzing how to put products into practical use); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu 1))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to assist research and development to put thin film solar cells for power use into practical use and a research to put thin film solar cell manufacturing technologies into practical use, survey and research have been performed on trends in the technologies inside and outside the country. Characteristic points in thin film solar cells during the current fiscal year include: expansion of production scale of amorphous silicon solar cells, rapid progress in poly-crystalline silicon thin film solar cell technologies, and enhancement of performance in large-area modules in the a-Si, CIGS, and CdTe systems. In the trends in research and development of amorphous systems, expectation is heightening on elucidation of optical deterioration phenomena, and establishment of suppression technologies thereof. Although the highest efficiency was not renewed in thin film solar cells of small areas, progress was seen in the post-stabilization efficiency in large-area modules. A thin film solar cell manufacturing plant having an annual production capacity of 20 MW was put into operation in October in Japan. Micro (poly) crystalline silicon based solar cells have high possibility of being compatible in cost reduction and performance improvement, and energetic researches are being carried out on them in recent years as the most promising candidate of the next generation solar cells. (NEDO)

  13. Report on diagnosis and survey on research cooperation in the research cooperation promotion project in fiscal 1994. Research cooperation on manufacturing clean fuel for consumer use from gasified coal gas / Research cooperation on a method for pulp manufacturing of low-pollution and energy saving type by using non-wood raw materials; 1994 nendo kenkyu kyoryoku suishin jigyo 'kenkyu kyoryoku shindan chosa' hokokusho. Sekitan gas ka gas kara no minseiyo clean nenryo seizo ni kansuru kenkyu kyoryoku / himokuzaikei genryo wo mochiita teikogai shoenegata pulp seizoho ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    In solving the problems in developing technologies peculiar to developing countries, Japan will provide cooperation. This paper describes the achievements in diagnosis and survey in fiscal 1994. Development will be made on a manufacturing process for dimethylether (DME), a synthesizable and portable clean fuel, by using coal produced in China. Annual DME production of 10,000 tons will make it possible to supply 50,000 households with the fuel of one year consumption, whereas return on the construction investment and profit can be expected. At the Shanxi Coal Chemistry Research Institute, a 500 tons a year plant making DME from gasified coal gas is scheduled to begin operation. Development will be made on a pulp manufacturing technology in China, in which environmental pollution due to waste water is largely reduced, and operation cost is reduced. Application of the oxygen-alkaline evaporation and decomposition process developed in Japan will be considered, which uses non-wood raw material such as rice straw, wheat straw and megass). The raw materials are immersed continually in low-concentration alkaline solution, dehydrated, and then lignin is oxidized and decomposed by using oxygen in a continuous oxidation reactor to make the material into pulp. China uses non-wood materials as paper raw materials at 80%, whereas effects are expected in waste water pollution prevention, energy saving, resource saving and economics. (NEDO)

  14. Achievement report for fiscal 1997 on development of practical application technology for photovoltaic power generation systems. Development of technologies to manufacture thin film solar cells (development of technologies to manufacture silicon crystal based high-quality materials and substrates / survey and research on analysis of practical application); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (zairyo kiban seizo gijutsu kaihatsu / silicon kesshokei kohinshitsu zairyo kiban no seizo gijutsu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    As a plan to develop technologies to manufacture materials and substrates for thin film solar cells, it is intended to reduce defect density, enhance film forming speed, largely improve the photo-electric conversion efficiency and increase manufacturing productivity. These goals will be realized by establishing methods to control defect density, crystal particle diameters and crystallization rate in silicon crystal systems. A technology to form micro-crystal silicon-based thin films will be developed, that have superior photo-stability, and are capable of realizing low cost and mass production. Discussions will be given on a high-density plasma control technology, a fundamental property evaluation technology for micro crystal silicon thin films, and a device design simulation technology. A technology will be developed to form amorphous silicon layer on a stainless steel substrate by using the plasma CVD process. At the same time, discussions will be given on optical annealing and thermal annealing as reformation methods. Fiscal 1997 has surveyed component technologies to identify and analyze quickly and accurately the technical trends inside and outside the country, and to mass produce thin film solar cells. The Material and Substrate System Technology Subcommittee (silicon crystals) was held to deliberate the four-year development program and its progress. (NEDO)

  15. Metal oxide/hydrogen battery; Kinzoku sankabutsu/suiso denchi

    Energy Technology Data Exchange (ETDEWEB)

    Kanda, M.; Niki, H. [Toshiba Research and Development Centre, Komukai, Kawasaki (Japan)

    1995-07-04

    The metal oxide-hydrogen battery consisting mainly of hydrogen storage alloy has high energy density and high volume efficiency. However, it is disadvantageous that the self-discharge takes place since the discharge capacity is lowered due to the delivery of stored hydrogen from the hydrogen electrode. This invention relates to the metal oxide-hydrogen battery consisting of hydrogen storage alloy. Hydrogen storage alloy which is composed of LaNi5 system homogeneous solid solution having an equilibrium plateau pressure of less than 1 atm at 20{degree}C is used. As a result, the battery voltage change and the self-discharge can be reduced, and the cell performance can be improved. Examples of LaNi5 system hydrogen storage alloy are ANi(5-x)Mx (A = La, Mm, and Ca, M = Al, Mn, Si, Ge, Fe, B, Ga, Cu, In, and Co). LaNi(4.7)Al(0.3) and MmNi(4.2)Mn(0.8) are preferable. 3 figs.

  16. Cell with scrolled electrodes. Uzumaki jo denkyokutai wo sonaeta denchi

    Energy Technology Data Exchange (ETDEWEB)

    Kamibayashi, M.; Morioka, Y. (Sanyo Electric Co. Ltd., Osaka (Japan))

    1990-10-03

    Non-sintered electrode plates produced by direct filling of paste state active materials in metal fiber felt type porous body are proposed recently for use as electrode plates for alkali cells and the like. Although this type of electrode plates can be produced with a simple facility because sintering process is not required, it has a shorcoming of internal short circuiting because metal fibers pass through the separator due to fuzzing of metal fiber. According to this invention, a sheet comprising metallic fibers oriented at right angles against the scrolled direction of the electrode plate is stacked on the surface of the metal fiber felt type porous body sheet when it is scrolled with the interposed separator. As the result, fibers are not bent and does not protrude from the surface of sheet to pass through the separator because each metallic fiber comprising the metallic sheet on the surface are arranged at a right angle against the direction of scrolling of the porous sheet. 2 figs., 1 tab.

  17. Solar cell driving device. Taiyo denchi kudo sochi

    Energy Technology Data Exchange (ETDEWEB)

    Yamazaki, K [Shibaura Engineering Works Co. Ltd., Tokyo (Japan)

    1991-01-24

    In driving a motor by a solar cell, if the sun light is weak, the motor cannot be started because of the fact that the start-up current of the motor is more than the current needed for driving. In this invention, a current limiting circuit is placed between the solar cell and the load, whereby the current limitation by said limiting circuit is released when the detected voltage of the solar cell reached the value required for starting the load. The current limiting circuit uses a semiconductor element such as a thyrister and a transistor which general limits a current. Such a current limiting circuit is controlled by a voltage detecting circuit and is so constructed that the cell limitation is released when a specific preset volatge of the solar cell is reached. 2 figs.

  18. Solar cell element, solar cell system, and illuminating system; Taiyo denchi soshi, taiyo denchi sochi oyobi shomei system

    Energy Technology Data Exchange (ETDEWEB)

    Oka, Y. [Toshiba Laytech Co. Ltd., Tokyo (Japan)

    1997-12-12

    This invention relates to provision of a photocatalytic film on the light intercepting surface for the solar cell substrate of the solar cell element, which transmits the lights in the wavelength region longer than ultraviolet, i.e. 410nm and longer wavelength lights, and intercepts the lights in ultraviolet wavelength region. This photocatalytic film retards the decrease in the light interception by the solar cell element, and simplifies the maintenance because it oxidizes and decomposes organic matters by the less than 410nm ultraviolet ray contained in the sunlight to prevent adhesion of organic substance on the light intercepting surface of the solar cell element. In addition, decomposed dirt composition is washed away to accelerate dirt removing performance by rain waterdrop adhesion on the intercepting surface when it is used outdoors. As to this photocatalytic film, the thickness from 0.01 to 0.5{mu}m is desirable, effective phtocatalytic activity can not be expected if the thickness is less than 0.01{mu}m, and transmission factor becomes smaller if the thickness exceeds 0.5{mu}m, producing no electromotive force. TiO2, ZnO, and FeTiO3 are used as such photocatalyst. 6 figs.

  19. Study of fuel control strategy based on an fuel behavior model for starting conditions; Nenryo kyodo model ni motozuita shidoji no nenryo hosei hosho ni tsuite no kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Nakajima, Y; Uchida, M; Iwano, H; Oba, H [Nissan Motor Co. Ltd., Tokyo (Japan)

    1997-10-01

    We have applied a fuel behavior model to a fuel injection system which we call SOFIS (Sophisticated and Optimized Fuel Injection System) so that we get air/fuel ratio control accuracy and good driveability. However the fuel behavior under starting conditions is still not clear. To meet low emission rules and to get better driveability under starting conditions, better air/fuel ratio control is necessary. Now we have understood the ignition timing, injection timing, and injection pulse width required in such conditions. In former days, we analyzed the state of the air/fuel mixture under cold conditions and made a new fuel behavior model which considered fuel loss such as hydrocarbons and dissolution into oil and so on. Al this time, we have applied this idea to starting. We confirm this new model offers improved air/fuel ratio control. 6 refs., 9 figs., 3 tabs.

  20. Hydrogen battery car developed in Matsuda; Matsuda suiso nenryo denchisha wo kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-06-01

    Matsuda announced that the hydrogen battery car 'Demio FCEV' was developed by the company. This new type car not only does not need an air humidifying machine, but also supplies the necessary electricity with an ultra capacitor of a large scale condenser. Its maximum output is 40 kw, the highest speed is 90 km per hour, and the accelerating time from the stop state to 40 m is about 5 seconds, the same level as a gasoline car. One time of hydrogen charging serves for 170 km running. As a hydrogen battery car, it is the third one in the world, following the DAIMURA in Germany and TOYOTA. (translated by NEDO)

  1. Methanol as moter fuel in 21 century; 21 seiki no jidosha nenryo to metanoru

    Energy Technology Data Exchange (ETDEWEB)

    Tominaga, H [Saitama Inst. of Technology, Saitama (Japan). Faculty of Engineering

    1996-02-01

    When the oil resources situation is taken into consideration, it is important to prepare now for the demand and supply situation of oil in the 21st century. The first method of the preparation is the noble-use of oil. The second method is the development and popularization of energies for transportation equipment which can take the place of petroleum. The candidates are synthetic liquid fuel, natural gas, and electricity (secondary batter). Methanol is the only synthetic liquid fuel which has the possibility of competing with petroleum both technologically and economically. By using methanol, cleaner combustion can be expected as compared with petroleum and coal. Methanol can be produced via synthetic gas not only from coal but also from natural gas, oil sand, oil shale, and biomass. From the technological point of view, innovation of quantity production technology of methanol is the first important subject. The second importance is the development of methanol vehicles and methanol fuel. Presently, methanol vehicles and fuels are in the stage of wide range and long-term verification test by running actual vehicles. 1 tab.

  2. Evaluation of PV modules integrated with roofing materials; Kenzai ittaigata taiyo denchi module no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Morizane, M.; Yagiura, T.; Nakashima, S.; Yagi, H.; Murata, K.; Uchihashi, K.; Tsuda, S.; Nakano, S. [Sanyo Electric Co. Ltd., Osaka (Japan); Ito, M.; Kurimoto, T.; Yamakawa, H.; Fujiwara, T. [Kubota Corp., Osaka (Japan)

    1997-11-25

    PV modules unified with building materials which are low in cost, easy to install and excellent in designing were developed and were evaluated in various tests. As to the basic structure of this module, seamless and unified construction with the back metal plate was adopted considering improvement in fire prevention and cost reduction. About the installation, module is easy to install by just fit connection with the frame, and easy to remove with no use of special tools. Concerning intensity and durability requested for this module, tests on reliability such as torsion strength and wind pressure resistance were conducted according to JIS standards, and it was confirmed that there were no problems. Also on the long-term durability, tests on long-term reliability were carried out by doubling test terms of the temperature/humidity cycle test, salt water resistance test, etc., and the reliability the same as that of the existing type was confirmed. In the verification test using a model house, no changes were seen in electrical characteristics and appearance, and waterproof was also favorable one and a half year after the installation. 4 refs., 7 figs., 5 tabs.

  3. Metal oxide/hydrogen secondary battery; Kinzoku sankabutsu/suiso niji denchi

    Energy Technology Data Exchange (ETDEWEB)

    Hosobuchi, H.; Ema, M.

    1995-12-12

    Since the shape of powder produced by crushing the hydrogen storage alloy containing rare earth element varies widely, the density of the negative electrode made by packing the alloy powder is low. As a result, the secondary battery employing this negative electrode has a small discharge capacity. This invention solves the problem. Employing the hydrogen storage alloy containing rare earth element composed of particle shape of aspect ratio, A, of over 1.0 and below 3.0 gives rise to the negative electrode with high packing density, improving the discharge capacity of the metal oxide - hydrogen secondary battery. The more the shape of powder of hydrogen storage alloy containing rare earth element is near to sphere, the higher the packing density of negative electrode made of the hydrogen storage alloy containing rare earth element becomes. The preferable aspect ratio, A, of the powder is 1.0 {le} A {le} 2.0. Such alloy powder can be produced by mechanically grinding the rare-earth-element-containing hydrogen alloy ingot, or grinding by hydration, or grinding by atomizing followed by sieving. 1 fig., 1 tab.

  4. Metal oxide-hydrogen secondary battery; Kinzoku sankabutsu-suiso niji denchi

    Energy Technology Data Exchange (ETDEWEB)

    Hosobuchi, H.; Edoi, M.; Katsumata, T.

    1995-06-06

    Recently, the metal oxide - hydrogen secondary battery characterized by employing the hydrogen storage alloy as the hydrogen negative electrode draws attention. However, the secondary batteries equipped with the negative electrode composed of hydrogen storage alloy powder have such shortcoming that the charge-discharge cycle life is rather short and it changes widely from battery to battery, as the hydrogen storage alloy is disintegrated. This invention solves the problem. Employing the alloy having a composition expressed as LmNi(w)Co(X)Mn(y)Al(z) (Lm = rare earth elements including La) can suppress the disintegration of hydrogen storage alloy powder during the charge-discharge cycle. In addition, controlling the oxygen content in the hydrogen storage alloy powder to 500 - 1500ppm can reduce the oxidation corrosion of the hydrogen storage alloy, resulting in suppression of its deterioration. 1 fig., 2 tabs.

  5. Both hydrogen and electricity chargeable battery; Suiso to denki de juden kanona denchi kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-06-01

    Kuriyama group of the Osaka Industrial Research Institute developed a new air-metallic hydride battery that is chargeable by both electricity and hydrogen gas. The battery uses a hydrogen storage alloy as the negative pole and uses active carbon coated with platinum as the positive pole. Potassium hydroxide aqueous solution is used as the electrolyte, and a space is arranged in the negative pole for contacting and absorbing the hydrogen with a good efficiency. The key point is the development of the hydride for energy storage that can well absorbs the hydrogen gas even it is dampened by the electrolyte. And the pole is prepared by pulverized the particles of rare earth hydrogen storage alloy having the particle size smaller than 150 micron meter, forming a Ni layer for a catalyst to absorb hydrogen, adding fluorinated resin dispersant for the sake of repellency and forming a sheet. In a test running, a half of hydrogen storage capacity is realized by charging for 30 minutes. And, 0.6 V electricity of 10 mA per unit pole area of 1cm{sup 2} is continuously obtained for 17 hours during discharging. While a third electrode is formed by nickel hydroxide, the battery is chargeable and dischargeable as the same as nickel hydrogen battery. Low cost and small size can be expected by a combination of respectively prepared fuel battery with nickel hydrogen battery. (translated by NEDO)

  6. To the partnership in Kanegafuchi Chemical Industry and solar cell; Kaneka, taiyo denchi de teikei he

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    Kanegafuchi Chemical Ind. clarified that the consultation was advanced in the direction in which the business cooperates with BP Amoco Corp. in international oil majors on the solar cell business on 11 th capital. In full amount fund subsidiary of the bell pool chemistry, the solar cell making and selling company is established in the joint venture in Europe and America, Asia, when the BP Amoco Corp. does capital participation in money mosquito solar tech which is the production marketer of solar cell. The plan which develops the amorphous solar cell of low cost which the bell pool chemistry developed in the world. The consultation of the partnership is also arranging prospect in the end June, and it seems to greatly jump by uniting with the BP Amoco Corp. of the largest hand. (translated by NEDO)

  7. PV glass curtain walls; Kenzai ittaigata taiyo denchi gaiheki no kaihatsu (glass curtain wall eno tekiyo)

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, T.; Iwai, T.; Ouchi, T.; Ito, T.; Nagai, T.; Shu, I. [Kajima Corp., Tokyo (Japan); Arai, T. [Showa Shell Sekiyu K.K., Tokyo (Japan); Ishikawa, N.; Tazawa, K.

    1997-12-20

    Reported in this article are PV (photovoltaic) modules now under development for integration into building walls. First of all, the power generating capability of PV modules and appropriate use of the generated power are studied, and the performance (resistance to fire or incombustibility, strength and durability, appearance and design, and dimensional standardization) that such outer wall materials are to be equipped with are determined. Next, module development, installation technique, computer graphics-aided facade designing, and real size module-using proof test are studied before installability, the power to be generated, and designs are finalized. In the development of modules, design evaluation involves the combining of various kinds of glass, solar cells, back sheets, and fillers, and the importance is confirmed of the prevention of insulation degradation around the modules. As for the methods of installation, the gasket method and aluminum sash method, etc., are tested. In the study of facade design, it is found that various expressions are possible by properly choosing gasket colors, module types, and kinds of glass to cover the openings. 1 ref., 6 figs., 3 tabs.

  8. Research on natural gas fuel injection system. Development of high-performance pressure regulator; Tennen gas yo nenryo funsha system no kenkyu kaihatsu. 1. Tennen gas nenryo funshayo no koseino regulator kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kato, S; Ishii, M; Takigawa, B; Makabe, K; Harada, S; Ono, H [Nippon Carburetor Co. Ltd., Tokyo (Japan)

    1997-10-01

    With the aim of further reducing the exhaust emissions of natural-gas vehicles, vigorous research and development work is under way today on multi point gas injection (MPGI) system. In this studies, a high-performance pressure regulator, which is one of the main components of this MPGI system, has been newly developed. The results showed that a significantly better accuracy of the regulated pressure level using this regulator was obtained under the wide range of operating conditions, including instantaneously greater changes of fuel flow rate. In addition, the advanced studies of gaseous fuel injectors (GFIs) would be also conducted. 4 refs., 8 figs.

  9. Technology assessment on a hydrogen fueled aircraft system; 1980 nendo suiso nenryo kokuki system ni kansuru technology assissment

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This paper describes technology assessment on a hydrogen fueled aircraft system. Indispensable as technological assignments are structuring different safety systems including prevention of leakage and ignition, not to speak of developing an airframe structure that considers cryogenic and brittle nature of liquefied hydrogen. Operation related industries would be subjected to increased burdens, such as purchase and servicing of new implements and materials, but the liquefied hydrogen industry will have a chance of growing largely with wide repercussions. In the environmental aspect, the aircraft will have less CO and SOx emission in exhaust gas and lower noise than the conventional jet aircraft. Technological problems to be solved in the development include the safety of fuel tanks, safety assurance measures, and liquefied hydrogen of the required amount to be supplied easily and at low cost. To meet these requirements, noticeable progress is demanded in hydrogen manufacturing technologies. What is also required is explosion-proof safety that does not have to require crews to take special considerations in take-off and landing, not to speak of during flight. This also applies to fuel feeding and servicing on the ground. Considerations must be given that rise in operation cost should not be excessive. (NEDO)

  10. Upgrading of brown coal by slurry-dewatering; Kattan no yuchu dassui ni yoru clean kotai nenryo no seizo

    Energy Technology Data Exchange (ETDEWEB)

    Okuma, O.; Shimizu, T.; Inoue, T.; Shigehisa, T.; Deguchi, T.; Katsushima, S. [Kobe Steel, Ltd., Kobe (Japan)

    1996-10-28

    This paper describes an outline of solid fuel production process from brown coal and the investigation results of its elemental techniques. Dried coal is produced by this process which consists of a dewatering of crushed brown coal in oil-based solvent, a solid and liquid separation of slurry, and a remained oil recovery by heating. This process is characterized by the higher thermal efficiency compared with usual drying and the restraint of spontaneous combustion of product coal. It was revealed that solid fuel with low moisture, low ash, low sulfur, and suppressed spontaneous combustion property can be produced from Australian brown coal through this process. From the comparison between kerosene and fuel oil A, it was confirmed that the oil content during dewatering was smaller and the oil recovery by heating was easier by using a solvent with lower boiling point. It was also confirmed that the spontaneous combustion property can be suppressed using small amount of asphalt by solving asphalt in the solvent and adsorbing asphalt on the surface of brown coal. From these results, low rank coals including brown coal, which are difficult to use, are expected to be used as clean coal with low ash and low sulfur through this process. 2 refs., 7 figs., 2 tabs.

  11. Fabricating method of gas diffusion electrode for fuel cell. Nenryo denchiyo gas kakusan denkyoku no seizo hoho

    Energy Technology Data Exchange (ETDEWEB)

    Harada, H [Yokohama (Japan)

    1994-01-28

    Cation exchange film is pressure bonded by hot-pressing on an aluminium foil for the solid high polymer electrolyte fuel cell which uses the cation exchange film as the electrolyte (PEMFC), but the conditions for the hot-pressing are severe because the softening temperature of polytetrafluoroethylene used as the binder for the bonding is higher than that of the cation exchange film. This invention is concerned with a method of improving adhesion and binding between the cation exchange film surface and the electrode catalyst layer, wherein K or Na type perfluorosulfonic acid system copolymer of the same material as that used for the cation exchange film is used as the binder in preparing the electrode catalyst layer of PEMFC, and the softening temperature of the cation exchange film itself is increased to enable high temperature hot-pressing. It is desirable to use the cation exchange film with the dry film thickness from 50 to 150[mu] and ion exchange capacity from 0.83 to 1.43 milli-equivalent/g (dry resin). 1 fig.

  12. Fabricating method of gas diffusion electrode for fuel cell. Nenryo denchiyo gas kakusan denkyoku no seizo hoho

    Energy Technology Data Exchange (ETDEWEB)

    Harada, H [Yokohama (Japan)

    1994-01-28

    When the cation exchange film of the solid high polymer electrolyte fuel cell which uses the cation exchange film as the electrolyte (PEMFC) is bonded with the electrode catalyst layers for the anode and cathode, the hot-press conditions are severe and satisfactory bonding is hard to be achieved because the softening temperature of polytetrafluoroethylene used as the binder for the bonding is higher than that of the cation exchange film. This invention is concerned with a means of obtaining PEMFC which can generate high cell voltage, wherein perfluorosulfonic acid system copolymer solution or dispersed solution similar to that used for the cation exchange film is used as the binder when bonding carbon cloth or carbon paper coated with electrode catalyst layers for anode and cathode to the cation exchange film, setting of hot-pressing conditions is made easier, and the adhesion and bonding of the cation exchange film surface and the electrode catalyst layers are improved. 1 fig.

  13. Analysis of fuel spray characteristics for premixed lean diesel combustion; Kihaku yokongo diesel kikan ni okeru nenryo funmu kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, S; Harada, a; Miyamoto, T; Akagawa, H; Tsujimura, K

    1997-10-01

    Premixed lean diesel combustion (PREDIC) makes it possible to achieve low NOx emission. It is an important factor to make the homogeneous spray formation for PREDIC. In this paper presents I the effect of the spray dispersion on emission characteristic were analyzed with the spray observation and engine test. Pintle type nozzle, which has different feature from orifice type nozzle, are used to form the hollow cone spray. As a result, the pintle type nozzle having grooves to generate the swirl flow, makes the reduced penetration in comparison with the hole nozzle under low ambient gas pressure. And it could improve THC, CO emissions at low NOx emission condition. 7 refs., 12 figs., 1 tab.

  14. Development of coal gas production technology acceptable for fuel cells; Nenryo denchiyo sekitan gas seizo gijutsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T [Center for Coal Utilization, Japan, Tokyo (Japan); Kimura, N; Omata, K [Electric Power Development Co. Ltd., Tokyo (Japan)

    1996-09-01

    In utilizing coal for high-efficiency direct power generation using fuel cells, it is necessary that coal be fed into the fuel cells after having been made into ash-free gaseous fuel. Research and development works are being carried out with an objective to develop a coal gasification furnace most suitable for fuel cells and establish a system to refine coal up to the one that can be fed into fuel cells. Fiscal 1995 has conducted investigations on coal gasification technologies, air separation technologies, and gas refining technologies as the important element technologies, and a trial design on integrated coal gasification fuel cell (IGFC) systems. This paper reports from among the above items the result of the trial design on an IGFC system using molten carbonate fuel cells. The paper describes system comparison on paths of produced gases and anode waste gas, comparison on refining processes using a wet system and a dry system, and parameter studies on oxygen concentration in gasifying agents. It was made clear that the suitable furnace is an oxygen blown coal gasification furnace, and the power generation efficiency at the system terminal can be higher than 53%. 11 figs., 6 tabs.

  15. Development of ceramic roller bush for diesel fuel injection pump; Nenryo funsha pump yo ceramics sei roller bush no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Noda, K; Kamiya, S; Fujimura, M; Tsuzuki, M [Toyota Motor Corp., Aichi (Japan); Taniguchi, K [Denso Corp., Aichi (Japan)

    1997-10-01

    Silicon nitride ceramics have been applied to roller bush for diesel fuel injection pump in order to improve the seizure resistance. It was found that ceramic roller bush made it possible to improve the seizure load by more than three times as compared to conventional metal roller bush when the kerosene was used as lubricant The ceramic roller bush proved to be durable under engine operating conditions. 6 refs., 13 figs., 1 tab.

  16. Research study of conjugate materials; Conjugate material no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper reported an introductory research on possibilities of new glass `conjugate materials.` The report took up the structure and synthetic process of conjugate materials to be researched/developed, classified them according to structural elements on molecular, nanometer and cluster levels, and introduced the structures and functions. Further, as glasses with new functions to be proposed, the paper introduced transparent and high-strength glass used for houses and vehicles, light modulation glass which realizes energy saving and optical data processing, and environmentally functional glass which realizes environmental cleaning or high performance biosensor. An initial survey was also conducted on rights of intellectual property to be taken notice of in Japan and abroad in the present situation. Reports were summed up and introduced of Osaka National Research Institute, Electrotechnical Laboratory, and National Industrial Research Institute of Nagoya which are all carrying out leading studies of conjugate materials. 235 refs., 135 figs., 6 tabs.

  17. Fiscal 1999 geothermal development promotion survey. Development potentiality survey - Strategic survey/nation-wide survey (Report on districts in Fukushima Prefecture); 1999 nendo chinetsu kaihatsu sokushin chosa. Kaihatsu kanosei chosa - senryakuteki chosa zenkoku chosa (Fukushimaken chiiki hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-08-01

    For the effective implementation of the survey, data in existence were reanalyzed for the Bandai-Azuma district and Minami-Aizu/Nasu district, and a wide area geothermal model was built. Using the model, exploitable resources were assessed and a prioritized survey introduction program was worked out for the promotion of geothermal development. In compliance with the strategic survey implementation manual, the Bandai-Azuma district was assessed, and the northeastern-eastern foot area of Azuma Volcano and the northern foot area of Adatara Volcano were extracted as areas promising geothermal energy development. The Monte Carlo method was applied to the prioritized survey area at the northeastern foot of Azuma Volcano, and then it was estimated that, with a probability of not less than 90%, the exploitable resources would be 6.4MWe in the case of data accuracy of 0.5 or more and 12.0MWe in the case of data accuracy of 0.4 or more. Selected as promising areas in the Minami-Aizu/Nasu district were the Yanaizu-Nishiyama area, the neighborhood of Nasudake-Chausudake, and the neighborhood of Shiobara-Fuji. (NEDO)

  18. Research report of fiscal 1997. Study on total energy and material control (feasibility study on circulating society); 1997 nendo chosa hokokusho. Total energy and material control ni kansuru chosa (junkangata shakai kochiku kanosei chosa) chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In order to construct real sustainable global environment and human society in the 21st century called the century of environment, not only the innovation of manufacturing processes technically supporting such the construction but also the conception including the innovation of the whole society from a wide viewpoint are essential. As a total energy and material control system (TEMCOS) concept, the view of an energy-saving circulating society is attempted which minimizes a total energy and material flow in Japan, and the role and issue of manufacturing industry, in particular, material industry are extracted. As one of the targets of such a concept, the conception of an eco-town is also described. Paying attention on some important material industries including a mass material flow and consuming a large amount of energy such as metal, plastics and automobile industries, the study result on a material flow for every industry is arranged, and some effective issues contributing to minimize a material flow and control energy consumption and CO2 emission are extracted. 80 refs., 67 figs., 30 tabs.

  19. Fiscal 1999 research on geothermal energy development promotion. Research report on development feasibility (Strategic survey - nationwide survey); 1999 nendo chinetsu kaihatsu sokushin chosa hokokusho. Kaihatsu kanosei chosa (senryakuteki chosa zenkoku chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-10-01

    Analysis and assessment were conducted for each of promising geothermal regions over large areas so as to contribute to the drafting of survey implementation plans and estimation of the amounts of recoverable geothermal reserves under the geothermal energy development promotion project. In this fiscal year, based on the manual compiled in the preceding fiscal year, studies were made on the six areas, which were the eastern part of Hokkaido, Toyoha-Niseko area, Iburi area, Bandai-Azuma area, Minamiaizu-Nasu area, and the island area. In region 1 in the eastern part of Hokkaido, a 48km{sup 2} was extracted in the vicinity of Mount Musa, with the amount of resources per 1km{sup 2} estimated at 12.34-56.02MWe. In region 2 in the eastern part of Hokkaido, promising geothermal regions I, II, III, and IV were extracted, with the amounts of resources per 1km{sup 2} estimated at 50MWe or more at III and part of IV. In the Toyoha-Niseko area, promising regions I and II were extracted, the amounts of resources estimated at 50MWe or more in both regions. For the Iburi area, it was concluded that there was a probability of not less than 90% that the amount of resources was 50MWe or more and it was proposed that an additional survey be conducted. As for the Bandai-Azuma, Minamiaizu-Nasu, and island areas, need of further surveys was pointed out. (NEDO)

  20. Fiscal 1999 geothermal development promotion survey. Development potentiality survey - Strategic survey/nation-wide survey (Report on Hokkaido region); 1999 nendo chinetsu kaihatsu sokushin chosa. Kaihatsu kanosei chosa - senryakuteki chosa zenkoku chosa (Hokkaido chiiki hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-08-01

    For the effective implementation of the survey, an analysis was conducted into areas expected to be successfully developed for geothermal energy, and promising areas and prioritized survey areas were selected. Data then in existence were collected at the Doto district 1, Doto district 2, Toyoha-Niseko district, and the Iburi district and subjected to reanalysis, and a wide area geothermal system conceptual model was built. Using the model, development-promising areas were extracted, the amount of resources was assessed, and an optimum survey program was prepared. One promising area was selected in the Doto district 1, four in the Doto district 2, two in the Toyoha-Niseko district, and one in the Iburi district. As prioritized survey areas, Musadake was selected in the Doto district 1; Yoichidake, Yunosawa, and Takinosawa in the Toyoha-Niseko district; and Raibadake in the Iburi district. A Monte Carlo analysis was conducted, and the result indicated that Musakake had 93-121MWe in resources of which 55MWe would be exploitable with a probability of not less than 90%. (NEDO)

  1. Verification test for an electric vehicle using capacitor-battery series connection for battery load levelling; Denchi no fuka heijunka no tame no kyapashita to denchi no chokuretsu setsuzoku hoshiki wo saiyoshita denki jidosha no jissho shiken

    Energy Technology Data Exchange (ETDEWEB)

    Miyaoka, K.; Takehara, J.; Kato, S. [Chugoku Electric Power Co. Inc., Hiroshima (Japan)

    1998-03-25

    For the prolongation of the distance that an electric vehicle (EV) can cover on a single charge and of the service life of the EV battery unit, a system is developed, in which the battery unit and the capacitor unit are connected in series for the levelling-off of battery peak loads, and the system is tested aboard a running real vehicle. Installed on the real vehicle is a battery unit that is a series connection of 20 12V-38Ah seal-type lead-acid batteries, each battery consisting of two cells connected in parallel. Driving the vehicle is a DC brushless motor capable of a maximum operation of 9000rpm. Also installed is a capacitor unit that is a parallel connection of 40 2.3V-1800F capacitors, each capacitor consisting of two capacitors connected in parallel. Findings are described below. In a 0-400m acceleration test, 22.5 seconds is recorded with the capacitor unit in operation, meaning an improvement of 0.7 seconds. The maximum speed remains unchanged at 110km/h, which agrees with the pre-calculated value. Although the battery peak load reduction rate in a 15-mode drive pattern marks 23%, the distances covered on a single charge in this drive pattern turn out to be almost the same whether the capacitor unit is in operation or not. 3 refs., 15 figs., 3 tabs.

  2. Research report of fiscal 1997. Feasibility research on domestic wind farms; 1997 nendo chosa hokokusho. Kokunai wind farm kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research was made on large-scale wind power generation projects under planning or construction. Issues of the following 5 areas were arranged considering topographic, geographic and meteorological conditions, and the type of municipal corporations: Tomamae town, Hokkaido, Tachikawa town, Yamagata prefecture (third-sector), Hisai city, Mie prefecture, Otoyo town, Kochi prefecture, and Kishuku town, Nagasaki prefecture (third-sector). These projects are supported by MITI`s local new energy introduction promotion project subsidy started in fiscal 1997 covering a half of construction cost (within 200 million yen/year). Requirements for this subsidy are that an applicant is either a municipal corporation or a third-sector, and that a total generating capacity is not less than 1200kW. Another subsidy system covering 1/3 of construction cost and a debt guarantee system are prepared for large-scale private projects not less than 800kW. Hearing was made on some private projects in Esashi town, Akita city and Hasaki town. Technical requirements, specifications, guideline and some examples for system interconnection are also summarized. 10 figs., 24 tabs.

  3. Fiscal 1995 geothermal development promotion survey. Natural environment survey report; 1995 nendo chinetsu kaihatsu sokushin chosa. Shizen kankyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    In Candidate C area for the geothermal development survey, the natural environment was surveyed and `the secondary landscape assessment` was summed up in which places proposed for drilling of large-size wells and for construction of power generation facilities are extracted and a simulation of the landscape is conducted. The area for survey is the Shiramizu-gawa region in the south of Lake Akan, Akan-cho, Akan-gun, Hokkaido. The field survey was carried out about three items of landscape, plants and animals during the June-November period, 1995. As to the flora, diverse florae including vegetation unique to alpine areas, wetlands, and fumarole surrounding areas were found in the region, which is covered with summer-green broad-leaved forests or mixed forests of coniferous and broad-leaved trees. As to the fauna, faunae inhabitant of the highly natural forests were found including black woodpeckers and mountain hawk eagles. As a result of studying the places proposed for geothermal development from the above-mentioned survey, two places were picked up in the west of the survey area, where geothermal development is comparatively less influential in the natural environment and landscape and there is a high locational adaptability. 19 refs., 56 figs., 49 tabs.

  4. FY 1998 survey report. Petroleum substituting energy metering analysis survey; 1998 nendo chosa hokokusho. Sekiyu daitai energy keiryo bunseki chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In this survey, metering models in the Asian/Pacific region where energy demand is rapidly increasing were constructed which are used for the comprehensive analysis of the relations between changes in social structure such as economic growth, change in industrial structure, and progress in energy conservation technology and new energy technology, and the energy supply/demand structure. The survey was carried out aiming at contributing to the international development of Japan's energy policy in future by quantitatively analyzing/evaluating influences of various energy policies/economic policies on the economy and energy supply/demand, through various kinds of simulation models. In FY 1998, information collection for modeling was made in China and Korea out of the Asian/Pacific region. At the same time, pilot models were constructed, and simulation was made for the standard case. Moreover, an analysis was conducted of the relation between economic growth and motorization in each country of the world as the basic data preparation on energy consumption in the transportation sector. (NEDO)

  5. FY 1998 survey report. Petroleum substituting energy metering analysis survey; 1998 nendo chosa hokokusho. Sekiyu daitai energy keiryo bunseki chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In this survey, metering models in the Asian/Pacific region where energy demand is rapidly increasing were constructed which are used for the comprehensive analysis of the relations between changes in social structure such as economic growth, change in industrial structure, and progress in energy conservation technology and new energy technology, and the energy supply/demand structure. The survey was carried out aiming at contributing to the international development of Japan's energy policy in future by quantitatively analyzing/evaluating influences of various energy policies/economic policies on the economy and energy supply/demand, through various kinds of simulation models. In FY 1998, information collection for modeling was made in China and Korea out of the Asian/Pacific region. At the same time, pilot models were constructed, and simulation was made for the standard case. Moreover, an analysis was conducted of the relation between economic growth and motorization in each country of the world as the basic data preparation on energy consumption in the transportation sector. (NEDO)

  6. Influence of angle of inclination on power of solar module; Taiyo denchi module no keisha kakudo to shutsuryoku tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Tsutsumi, K.; Nishitani, M. [Dai Ichi University, College of Technology, Kagoshima (Japan)

    1997-11-25

    Experiment/study were conducted on the influence of angle of inclination on output of solar modules. In the experiment, changing the angle of inclination of the photovoltaic module installed on the top of school building to 0, 30, 60 and 90 degC, the global radiation on an inclined surface was measured by pyranometer equipped with the module, and at the same time output characteristics were measured by I-V curve tracer. In the I-V curve tracer, voltage, current, and output capability diagram are illustrated automatically changing bias voltage to get the maximum output. The global radiation on an inclined surface and the maximum output indicated an almost proportional relation and were expressed in a recursion method. Moreover, measurement of the global radiation is usually conducted using the amount of global radiation on a horizontal surface, and the global radiation on an inclined surface is calculated as a sum of the direct solar radiation amount and the sky solar radiation amount after determining a penetration rate by the relational equation. By calculating the global radiation on an inclined surface, it becomes possible to calculate the maximum output of photovoltaic modules by this recursion method. 1 ref., 6 figs., 1 tab.

  7. Influence of spectral solar radiation to the generating power of photovoltaic module; Taiyo denchi shutsuryoku eno taiyoko supekutoru eno eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Minaki, S.; Ishihara, Y.; Todaka, T.; Harada, K. [Doshisha University, Kyoto (Japan); Oshiro, T.; Nakamura, H. [Japan quality Assurance Organization, Tokyo (Japan)

    1997-11-25

    As to the influence of spectral solar radiation to generating power of solar cells, a study was conducted from the aspects of season, time zone, intensity of solar radiation, etc. In the study, spectral responsive variation correction coefficients were introduced as evaluation values expressing the influence of spectral solar radiation. For the spectral distribution, an all sky spectral pyranometer by wavelength was used, and data were used which were obtained in the measurement in experimental facilities of the solar techno center. Concerning solar cell relative spectral sensitivity values, used were relative spectral sensitivity values of monocrystal and amorphous standard solar cells to the short-circuit current. Spectral response variation correction coefficients are coefficients correcting variations in conversion efficiency of solar cells due to changes in the spectral distribution. The changes of spectral responsive variation correction coefficients were studied using data obtained during April 1994 and March 1996. As a result, it was found that the coefficients showed large changes in summer and small ones in winter and that amorphous solar cells indicate this trend conspicuously. 3 refs., 6 figs., 3 tabs.

  8. Development of nickel-hydrogen battery for electric vehicle; Denki jidoshayo nickel-suiso denchi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Research and development of battery, a main part of electric vehicle, have been promoted. Various batteries, such as lead battery, nickel-cadmium battery, nickel-hydrogen battery, lithium ion battery and so on, have been investigated for electric vehicles. Among these, nickel-hydrogen battery is superior to the others from the points of energy density, lifetime, low-temperature properties, and safety. It is one of the most prospective batteries for electric vehicle. Research and development of the nickel-hydrogen battery with higher energy density and longer lifetime have been promoted for the practical application by Tohoku Electric Power Co., Inc. This article shows main performance of the developed nickel-hydrogen battery for electric vehicle. The nominal voltage is 12 V, the rated capacity is 125 Ah, the outside dimension is L302{times}W170{times}H245 mm, the weight is 25.5 kg, the energy density is 60 Wh/kg, the output density is 180 W/kg, and the available environment temperature is between -20 and 60 {degree}C. 1 fig., 1 tab.

  9. High place working vehicles for nickel hydrogen battery powered distribution construction; Nikkeru suiso denchi kudoshiki haiden kojiyo kosho sagyosha

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-06-01

    The Tohoku Electric Power Co. Ltd., in combination with the Aichi Corporation, developed a low noise and no-exhaust gas high place working vehicle that uses NiH battery as a power for lifting or falling a bucket and cutting off electric wires. It is the first in the world that the large scaled NiH battery is used in the application field other than used as a running power of an electric automobile. The main characters of the battery may be pointed out as follows. (1) It has the energy density as 2 times as a lead battery, so 2 times of working time may be obtained by the same weight battery. (2) It is maintenance-free (a periodic maintenance is necessary for a lead battery). (3) Reduction of charging efficiency caused by the heat generated during the charging can be prevented by development of a battery cooling system. (4) As the battery is low noise and no exhaust gas, it does not trouble inhabitant anytime. The new type battery has been used in the Mizusawa business office and tested there by the end of 1998. (translated by NEDO)

  10. Nickel-hydrogen battery and hydrogen storage alloy electrode; Nikkeru suiso denchi oyobi suiso kyuzo gokin denkyoku

    Energy Technology Data Exchange (ETDEWEB)

    Ono, T. [Furukawa Electric Co. Ltd., Tokyo (Japan); Furukawa, J. [The Furukawa Battery Co. Ltd., Yokohama (Japan)

    1996-03-22

    Hermetically sealed nickel-hydrogen battery has such problem that the inner pressure of the battery elevates when it is overcharged since the oxygen gas evolves from the positive electrode. This invention relates to the hermetically sealed nickel-hydrogen battery consisting of positive electrode composed mainly of nickel hydroxide and negative electrode composed mainly of hydrogen storage alloy. According to the invention, the negative electrode contains organic sulfur compound having carbon-sulfur bond. As a result, the elevation of battery inner pressure due to the hydrogen gas evolution, the decrease in discharge capacity due to the repetition of charge and discharge, and the lowering of voltage after charging can be suppressed. The adequate content of the organic sulfur compound is 0.05 - 1 part in weight to 100 part in weight of hydrogen storage alloy. As for the organic sulfur compound, n-butylthiol, ethylthioethane, phenyldithiobenzene, trimethylsulfonium bromide, thiobenzophenone, 2,4-dinitrobenzenesulfenyl chloride, and ethylene sulphidic acid are employed. 2 figs., 1 tab.

  11. Hydrogen storage alloy and alkaline battery employing it; Suiso kyuzo gokin denkyoku to sorewo mochiita arukari niji denchi

    Energy Technology Data Exchange (ETDEWEB)

    Ono, T. [Furukawa Electric Co. Ltd., Tokyo (Japan); Furukawa, J. [The Furukawa Battery Co. Ltd., Yokohama (Japan)

    1997-01-28

    The invented hydrogen storage alloy electrode is produced in the following way: The hydrogen storage alloy powder is mixed with conductive material and rubber-like elastomer. A certain amount of viscosity modifier aqueous solution such as aqueous solution of carboxymethylcellulose is added to the said mixture to prepare a mixed paste. The said paste is dried and rolled after being filled in the current collector to be held by the current collector. The rubber-like elastomer has a strong bonding force, though it is soft. Both hydrophobic and hydrophilic groups are contained in its molecule. Example of such material is a partly fluorinated or chlorinated acrylonitrile-butadiene rubber. The addition of fluorine or chlorine atom is done to its double bond. The addition of the rubber-like elastomer is controlled to 0.05 - 10 wt% of hydrogen storage alloy powder to suppress the elevation of inner-battery pressure at the time of overcharge. 2 tabs.

  12. Estimation of the charge quantity from solar cell to battery; Taiyo denchi ni yoru chikudenchi eno juden yosoku

    Energy Technology Data Exchange (ETDEWEB)

    Tsutsumi, K; Nishitani, M [Daiichi University, College of Technology, Kagoshima (Japan)

    1996-10-27

    In performing an experiment of running a small electric vehicle by installing solar cells in it and by charging the storage battery at a specific voltage, an estimation was made on the charge quantity to the battery for each solar altitude and inclination of a module at different hours. The solar altitude was determined at Daiichi University, College of Technology, according to the month and the time of day from a formula using day-declination and time equation of a chronological table of science. The quantity of global solar radiation was determined by resolving the solar radiation into its direct and diffuse components on the basis of the extra-terrestrial solar radiation quantity with the change in radius vector taken into consideration; and then, the global solar radiation on the inclined face was obtained from the angle of inclination and incidence. On the roof of a Daiichi University building, solar cell modules were installed facing north and south at 0{degree}, 30{degree}, 45{degree}, 60{degree} and 90{degree} each, so that a short-circuit current was measured for each differently inclined angle. As a result of the experiment, shown in an regression formula is a relation between the temperature conversion value of the maximum output of the solar cell at the standard temperature of 25{degree}C and the quantity of solar radiation on the inclined surface. Consequently, it enabled the prediction of a charging quantity, in the case of running a small vehicle with solar cells installed, from the quantity of solar radiation on the inclined surface in the clear weather. 2 refs., 4 figs., 2 tabs.

  13. Stabilized efficiency of stacked a-Si solar cell; Sekisogata a-Si taiyo denchi no anteika koritsu

    Energy Technology Data Exchange (ETDEWEB)

    Takahisa, K; Kojima, T; Nakamura, K; Koyanagi, T; Yanagisawa, T [Electrotechnical Laboratory, Tsukuba (Japan)

    1997-11-25

    Different types of tests combining light and temperature were carried out in a laboratory on predicting long-term performance of stacked amorphous silicon solar cells. Cell terminals were left open, xenon was used as an irradiation light source, and cell temperature was controlled within {+-} 2 degC of the setting. The result of the experiment may be summarized as follows: with regard to the deterioration characteristics, the speed in which the efficiency changes reached a maximum within 10 hours, and thereafter the change has slowed down gradually in the case of temperature at 50 degC; in the case of 25 degC, the maximization is reached between 500 and 1000 hours; the stabilization efficiency turns out to be a pessimistic value according to the saturated value derived from an experimental expression, hence the value would have to be expressed by specifying cell temperatures, light intensities and elapsed time; the minimum value of seasonal variation may be estimated at about 85% as a pessimistic value; for recovery characteristics, the saturated value for the recovery tends to become lower as the lower the value immediately before the recovery; and if the light intensity is varied, the deterioration characteristic shifts to that at an individual light intensity. 4 refs., 11 figs., 2 tabs.

  14. On practicality of a hybrid car with solar cells; Taiyo denchi wo tosaishita hybrid car no jitsuyosei ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, K; Nagayoshi, H; Kamisako, K [Tokyo University of Agriculture and Technology, Tokyo (Japan)

    1997-11-25

    The paper stated a development of a hybrid car which is a parallel type with gasoline engine and electric motor as driving source (connecting each according to the situation) and is also equipped with solar cells. Specifications are gasoline engine of 1200cc, induction motor of 5.5kW, lead battery of 288V and 7.2kWh, monocrystal silicon solar cells of 180W maximum output, and body weight of 1100kg. The rear wheel is driven by electric motor, and the front wheel by gasoline engine. The car is loaded with battery charge use solar cells on hood and roof. To enhance cleaning degree, 1.6kW solar cells are installed as an installed power system and used for battery charge. Even by an electric motor with output less than that of the usual electric car, harmful exhaust gas emitted in start-up can be controlled. This is because the electric motor can be used in accelerating. It was confirmed that the power required for it could be supplied by solar cells installed on the car. The hybrid car is practically useful for prevention of local air pollution. 5 refs., 4 figs., 2 tabs.

  15. Forced-circulation solar water heater using a solar battery; Taiyo denchi wo mochiita kyosei junkahshiki taiyonetsu onsuiki

    Energy Technology Data Exchange (ETDEWEB)

    Asai, S; Mizuno, T [Yazaki Corp., Tokyo (Japan)

    1997-11-25

    Optimal operation control was discussed on a forced-circulation solar water heater using solar cells not only as the power supply of a heat collecting pump, but also for controlling operation of the heat collecting pump. With this system, when the amount of power generated by solar cells reaches a sufficient level for operating the heat collecting pump, the heat collecting pump starts operation, wherein the heat collecting medium circulates in the system. The discussion was given by using simulation based on experimental expressions such as the relation expression between insolation and heat collecting medium flow rate as derived from the result of the system`s heat collecting performance test. As a result, the following conclusions were obtained: optimal insolation for activating the discussed system is from 50 to 100 W/m {sup 2}, and the heat collected within this range is within -1.5% of the collected heat amount at an optimum value; optimal activating insolation for the case of 1000 to 2000 W/m {sup 2} with low daily cumulative insolation is from 0 to 50 W/m {sup 2}, whereas the optimal activating insolation amount increases as the daily cumulative insolation amount increases; and the optimal activating insolation amount increases as water to be supplied requires higher temperature. 1 ref., 17 figs., 2 tabs.

  16. Development of a Fe-Ni battery for electric vehicle use. Denki jidoshayo tetsu nickel denchi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Onozuka, T.; Okuda, K. (The Tohoku Electric Power Co. Inc., Sendai (Japan))

    1993-08-11

    Development has been made on an iron-nickel battery as a low polluting electric vehicle battery that is superior in low-temperature performance to lead-acid batteries. This paper summarizes the battery. The battery uses NiOOH for positive electrodes, Fe for negative electrodes, and alkaline aqueous solution for electrolyte. The battery was manufactured in the following manners to make it suit the electric vehicle application: The iron electrode was manufactured by mixing reduced iron powder having grain sizes from 5[mu] to 6[mu] with electrolyzed iron powder with grain sizes from 20[mu] to 30[mu] in a bonding agent, and sintered at temperatures from 750[degree]C to 800[degree]C in H2 atmosphere; iron electrodes that have superior life and material utilization factor were found to have reduced iron powder ratios from 20% to 30%; the nickel electrode consists of a substrate obtained by coating metallic Ni powder on a sheet and sintering it and filling it with NiOH; the electrolyte is composed of KOH containing LiOH and KS; the separator uses a ribbed PVC porous sheet; the container is made of PP; performance evaluation tests were conducted on discharge performance, energy density, output density, temperature characteristics, charge efficiency, and cycle life; and the results of vehicle driving tests surpassed those from lead-acid batteries. 6 refs., 18 figs., 6 tabs.

  17. Forced-circulation solar water heater using a solar battery; Taiyo denchi wo mochiita kyosei junkanshiki taiyonetsu onsuiki

    Energy Technology Data Exchange (ETDEWEB)

    Asai, S; Mizuno, T [Yazaki Resources Co. Ltd., Shizuoka (Japan)

    1996-10-27

    For the purpose of satisfying demands for qualitative improvement on tapwater temperature and pressure, an indirect-type solar water heater using solar cells, in which a closed type hot water storage tank connected directly to the water supply is integrated with a solar collector, was examined for its characteristics and performance. The heat collecting medium is a water solution of polypropylene glycol, which circulates through the solar collector pump, cistern, solar collector, and heat exchanger (hot water storage tank). The results of the test are summarized below. When comparison is made between the two solar collector pump control methods, the solar cells direct connection method and the differential thermo method utilizing temperature difference between the solar collector and the hot water storage tank, they are alike in collecting heat on clear days, but on cloudy days the latter collects 5% more than the former. In winter, when the heat exchanger heat transfer area is 0.4m{sup 2} large, a further increase in the area improves but a little the heat collecting efficiency. An increase in the medium flow rate and temperature, or in the Reynolds number, enhances the heat collecting efficiency. 13 figs., 6 tabs.

  18. Solar cell array for driving MOS type FET gate. MOS gata EFT gate kudoyo taiyo denchi array

    Energy Technology Data Exchange (ETDEWEB)

    Murakami, S; Yoshida, K; Yoshiki, T; Yamaguchi, Y; Nakayama, T; Owada, Y

    1990-03-12

    There has been a semiconductor relay utilizing MOS type FET (field effect transistor). Concerning the solar cells used for a semiconductor relay, it is required to separate the cells by forming insulating oxide films first and to form semiconductor layers by using many mask patterns, since a crystal semiconductor is used. Thereby its manufacturing process becomes complicated and laminification as well as thin film formation are difficult, In view of the above, this invention proposes a solar cell array for driving a MOS type FET gate consisting of amorphous silicon semiconductor cells, which are used for a semiconductor relay with solar cells generating electromotive power by the light of a light emitting diode and a MOS type FET that the power output of the above solar cells is supplied to its gate, and which are connected in series with many steps. 9 figs.

  19. Technological development for super-high efficiency solar cells. Technological development for crystalline compound solar cells (high-efficiency III-V tandem solar cells); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Kessho kagobutsu taiyo denchi no gijutsu kaihatsu (III-V zoku kagobutsu handotai taiyo denchi no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on technological development of III-V compound semiconductor solar cells in fiscal 1994. (1) On development of epitaxial growth technology of lattice mismatching systems, the optimum structure of InGaAs strain intermediate layers was studied for reducing a dislocation density by lattice mismatching of GaAs layer grown on Si substrate and difference in thermal expansion coefficient. The effect of strain layer on dislocation reduction was found only at 250dyne/cm in strain energy. Growth of GaAs layers on the Si substrate treated by hydrofluoric acid at low temperature was attempted by MBE method. As a dislocation distribution was controlled by laying different atoms at hetero-interface, the dislocation density of growing layer surfaces decreased by concentration of dislocation at hetero-interface. (2) On development of high-efficiency tandem cell structure, tunnel junction characteristics, cell formation process and optimum design method of lattice matching tandem cells were studied, while thin film cell formation was basically studied for lattice mismatching tandem cells. 45 figs., 8 tabs.

  20. Technological development for super-high efficiency solar cells. Technological development for super-high efficiency singlecrystalline silicon solar cells (super-high efficiency singlecrystalline Si solar cells); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Chokokoritsu tankessho silicon taiyo denchi no gijutsu kaihatsu (chokokoritsu tankessho silicon taiyo denchi cell no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on technological development of super-high efficiency singlecrystalline silicon solar cells in fiscal 1994. (1) On development of high-performance light receiving layer, the fine electrode for receiving surfaces was designed to reduce serial resistance, and the high-quality oxide passivation film was studied to reduce surface recombination velocity. (2) On development of forming technology of back heterojunction, the high-quality cell with B-doped fine crystalline Si film on its back was studied by heat treatment of the fine crystalline Si film, and the cell structure with high back reflectance of light was also studied. (3) On analysis for high-efficiency cells, the relation between the back recombination velocity at the interface between p-type substrate and back passivation film, and the internal collection efficiency as probe light was injected from the back, was calculated by numerical simulation. As a result, the cell back recombination velocity could be evaluated by measuring the spectral internal collection efficiency to back injection. 15 figs., 6 tabs.

  1. NEDO fuel/storage technology subcommittee. 18th project report meeting; NEDO nenryo chozo gijutsu bunkakai. Dai 18 kai jigyo hokokukai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    Taro Yamayasu, a NEDO (New Energy and Industrial Technology Development Organization) director, reports fuel and storage technologies, taking reference to the research and development of technologies relating to fuel cell power generation, cell power storage system of a novel type, ceramic gas turbine, superconductor-generated power application, wide-area energy utilization network system (urbane eco-energy system), high-temperature superconductor-supported flywheel power storage, demonstration of a novel method of load levelling, demonstration test for the establishment of a centralized control system, and so forth. Reported also is research and development involving a molten carbonate fuel cell power generation system, current status of distributed cell power storage system development (large lithium secondary storage battery technology development), current status of superconductor-generated power application technology, regenerative cycle type 2-shaft ceramic gas turbine for a 300kW-class cogeneration system, high-density latent heat transportation, and so forth. (NEDO)

  2. Design of hydroprocessing catalyst for the production of ultra clean fuels. Super clean nenryo wo mezashita jushitsu tanka suiso seisei shokubai no kokinoka

    Energy Technology Data Exchange (ETDEWEB)

    Shimada, Hiromichi (National Chemical Lab. for Industry,Tsukuba, (Japan))

    1990-02-01

    In order to develop high function catalyst for the ultra clean fuel refining and other purposes, the catalyst was studied in correlation between the function and structure. Hydrogenation power of aromatic ring and hydrogenolysis power of carbon-carbon bonding, which are principal functions of catalyst in the hydrogenation refining, were evaluated with model material. 30 kinds of catalyst were figure shown in classification result of evaluation. As for the mutual operation of molybdenum and carrier, it is necessary for molybdenum sulfide to be highly dispersed on carrier in order to heighten the hydrogenation activity. While the hydrogenolysis activity, as necessitating electrically negative molybdenum type to be formed on carrier, is manifested by the formation of Bronsted acidity point with hydrogen sulfide, adhering thereto. As for the molybdenum sulfide catalyst, mainly hydrogenation activity point, in case that structure, similar to molybdenum disulfide, is dispersed as a single layer on carrier, and hydrogenolysis activity point, in case that it forms a multi-layer structure thereon, are formed in edge part of respective crystal. The lowering in activity under a long time sevre condition, which mainly are carbonic material deposition, matallic adhesion, etc., is also influenced by the structural change in catalyst. 10 refs., 5 figs. 2 tabs.

  3. Effects of fuel and air mixing on WOT output in direct injection gasoline engine; Chokufun gasoline kikan ni okeru nenryo to kuki no kongo to shutsuryoku seino

    Energy Technology Data Exchange (ETDEWEB)

    Noda, T; Iriya, Y; Naito, K; Mitsumoto, H; Iiyama, A [Nissan Motor Co. Ltd., Tokyo (Japan)

    1997-10-01

    The effects of in-cylinder charge motion and the characteristics of the fuel spray and piston crown shape on WOT output in a direct injection gasoline engine are investigated. The fuel and air mixing process in a cylinder is analyzed by computer simulation and LIF method visualization. As a result, the technical factors to achieve enough mixing in a DI gasoline engine equipped with bowl in piston optimized for stratified combustion are clarified. 7 refs., 9 figs., 1 tab.

  4. Numerical simulation of fuel sprays and combustion in a premixed lean diesel engine; Kihaku yokongo diesel kikan ni okeru nenryo funmu to nensho no suchi simulation

    Energy Technology Data Exchange (ETDEWEB)

    Miyamoto, T; Harada, A; Sasaki, S; Shimazaki, N; Hashizume, T; Akagawa, H; Tsujimura, K

    1997-10-01

    Fuel sprays and combustion in a direct injection Premixed lean Diesel Combustion (PREDIC) engine, which can make smokeless combustion with little NOx emission, is studied numerically. Numerical simulation was carried out by means of KIVA II based computer code with a combustion submodel. The combustion submodel describes the formation of combustible fuel vapor by turbulent mixing and four-step chemical reaction which includes low temperature oxidation. Comparison between computation and experiment shows qualitatively good agreement in terms of heat release rate and NO emission. Computational results indicate that the combustion is significantly influenced by fuel spray characteristics and injection timing to vary NO emission. 10 refs., 8 figs., 1 tab.

  5. Effect of fuel composition on poly aromatic hydrocarbons in particulate matter from DI diesel engine; Particulate chu no PAH ni oyobosu nenryo sosei no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, S; Tatani, T; Yoshida, H; Takizawa, H; Miyoshi, K; Ikebe, H [COSMO Research Institute, Tokyo (Japan)

    1997-10-01

    The effect of fuel composition on poly aromatic hydrocarbons (PAH) in particulate matter from DI diesel engine was investigated by using deeply desulfurized fuel and model fuel which properties are not interrelated. It was found that the deeply desulfurized fuel have effect on reducing PAH emissions. Furthermore, it was suggested that poly aromatics in the fuel affect PAH emissions and the influence of tri-aromatics in the fuel was promoted by the coexistence of mono-aromatics or naphthene. PAH formation scheme from each fuel component was proposed by chemical thermodynamic data. 4 refs., 8 figs., 3 tabs.

  6. Soot and NOx simultaneous reduction by use of CO2 mixed fuel; Ekika CO2 yokai nenryo ni yoru diesel kikan no susu, NOx no doji teigen

    Energy Technology Data Exchange (ETDEWEB)

    Senda, J; Yokoyama, T; Ikeda, M; Fujimoto, H [Doshisha University, Kyoto (Japan); Ifuku, Y [Kubota Corp., Osaka (Japan)

    1997-10-01

    We propose the new fuel injection system by use of diesel fuel dissolved with CO2 to reduce both soot and NOx simultaneously. In this paper spray combustion characteristics of CO2 mixed fuel is reported. It is revealed that flame temperature and KL factor at the CO2 mixed fuel combustion are lower than at the only n-tridecane combustion due to separation or partly flashing of CO2component. And the result of exhaust gas measurement shows the capability that CO2 mixed fuel is able to reduce both soot and NOx simultaneously. 12 refs., 7 figs., 1 tab.

  7. Improvement of lean combustion characteristics of heavy-hydrocarbon fuels with hydrogen addition; Suiso tenka ni yoru kokyu tanka suisokei nenryo no kihaku nensho no kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Sakai, Y. [Saitama Institute of Technology, Saitama (Japan); Ishizuka, S. [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

    1999-09-25

    The Lewis numbers of lean heavy-hydrocarbon fuels are larger than unity, and hence, their flames are prone to extinction in a shear flow, which occurs in a turbulent combustion. Here, propane is used as a representative fuel of heavy-hydrocarbon fuels because the Lewis number of lean propane/air mixtures is larger than unity, and an attempt to improve its combustion characteristics by hydrogen addition has been made. A tubular flame burner is used to evaluate its improvement, since a rotating, stretched vortex flow is established in the burner. The results show that with' hydrogen addition, the fuel concentration, the flame diameter and the flame temperature at extinction are reduced and its combustion characteristics are improved. However, it is found that the effective equivalence ration at extinction cannot become so small as that of lean methane/air mixture, which has a Lewis number less than unity. (author)

  8. Effect of oxygenated fuel on premixed lean diesel combustion; Kihaku yokongo diesel nensho ni oyobosu gansanso nenryo kongo keiyu no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, S.; Miyamoto, T.; Harada, A.; Akagawa, H.; Tsujimura, K. [New ACE Institute Co. Ltd., Tokyo (Japan)

    1998-05-01

    Because injection timing in diesel engines is early in a premixed lean diesel combustion system using early fuel injection, ignition timing is determined by ignitability of the fuel used. The conventional diesel fuel, which has good ignitability, causes excessively early ignition, thus aggravating fuel consumption. In order to reduce cylinder temperature with an aim of delaying ignition timing to improve the fuel consumption, attempts are being made on using low cetane fuels to reduce CO2 gas supply or compression ratio, and to vary ignitability of the fuels. The present study investigated ignition timing control and properties of exhausts by mixing different types of oxygenated fuels into light oil. Mixing the oxygenated fuels into light oil proved that the ignition timing can be controlled, and mixing such low cetane fuels as ethanol and MTBE achieved improvement in fuel consumption. Trial use of the oxygenated fuels aggravated CO concentration, which is caused because the cylinder temperature was reduced. Numerical calculations suggest that use of fuels with faster evaporation speed and lower cetane number is effective in improving the fuel consumption and the exhausts. 12 refs., 9 figs., 2 tabs.

  9. Study of fuel spray characteristics for premixed lean diesel combustion; Kihaku yokongo diesel kikan ni okeru nenryo funmu keisei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, S.; Miyamoto, T.; Harada, A.; Akagawa, H.; Tsujimura, K. [New ACE Institute Co. Ltd., Tokyo (Japan)

    1998-05-01

    A study is being made on premixed lean diesel combustion (PREDIC) by means of early fuel injection in diesel engines. The PREDIC makes it possible to largely reduce NOx emission, but has such problems as ignition control and increase in THC and CO generation. In order to clarify the relationship between fuel spray characteristics in the PREDIC and properties of gas mixture and exhausts, the present study has investigated spread and internal structure of the spray by means of spray observation experiment using a pintle swirl nozzle. Based on the result therefrom, simulations were used to investigate effects of spatial dispersion characteristics of the spray on properties of the gas mixture and exhausts before ignition. The pintle swirl nozzle forms conical spray having an air layer inside the spray, where penetration is suppressed even under low atmospheric pressure. By forming hollow spray or solid spray in the conical spray, a possibility was indicated that equivalent ratio distribution of the gas mixture can be controlled and NO emission may be reduced. 8 refs., 12 figs., 1 tab.

  10. Cavitation characteristics of multihole diesel-fuel nozzles in high-speed oil flows. Diesel kikan yo nenryo tako nozzle no abura cavitation tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Yokota, M. (Shimonoseki Univ. of Fisheris, Yamaguchi (Japan)); Ito, Y. (Hachinohe Inst. of Tech., Aomori (Japan)); Aoki, H. (Xexel-Gleason U.S.A. Inc., New York (U.S.A))

    1991-07-25

    Recently, since higher velocity and higher pressure are required for diesel injection systems, cavitation behaviors in high velocity oil flows are strongly interested in such as 100 to 500 m/s for oil flow velocity and less than the cavitation factor {sigma} of 0.01. In this paper, oil cavitation characteristics at the injection part of multihole nozzles, especially on the flow characteristics, were studied systematically using fuel injection multihole nozzles for an actual use. As a result, it was clarified that subcavitation area (sub C), transition area, and supercavitation area (SC) could be existing in C{sub d}-{sigma} relation, which was similar to that specified cavitation conditions could be exisiting in the actual working area of multihole nozzles. And it was also clarified that flow coefficient C{sub d} relied on Reynolds number R{sub e} in the transition of {sigma}{ge}{sigma}{sub cr} and in {sub C} area, and mainly relied on {sigma} in SC area of {sigma}<{sigma}{sub cr}. Moreover, it was also confirmed that such tendency was similar to the one of the two-dimensional contraction of an area. 22 refs., 10 figs., 1 tab.

  11. Study of recent fuel oil cost in air lines (Part 2). Saikin no airline no nenyuhi ni kansuru ichikosatsu (2); Nenryo shohi to hiyo tai koka

    Energy Technology Data Exchange (ETDEWEB)

    Tanabe, Yoshikazu.

    1989-03-01

    Through an arrangement of published data about American air lines during 1985 through 1987, the overall expense vs. transportation fee (expense vs. effect) was studied as a main viewpoint. As a result, the fuel oil cost, even in case of wide fuselage plane, high in transportation efficiency, was high in ratio, 32 to 52% (3 to 5 times as high as that 12 to 14 years ago), and fluctuated connectedly with the oil price. While the jet fuel price fluctuated connectedly with the oil price per equal volume with 1.3 to 1.4 of price ratio. Further, the flight range ratio was recorded to be approx. 0.06 to 0.24 km/kg. While the transportation efficiency was lower than approx. 5000kg*km/kg with a wide range of overall expense, approx. 9 to 87 cents per compensative transportation ton*km. Because even a sudden decrease in transportation quantity did not decrease the overall expense, it was known to be important in management to secure the transportation quantity. 30 refs., 15 figs., 1 tab.

  12. Trend survey of the global environment adaptation type industrial technology. Chikyu kankyo tekiogata sangyo gijutsu doko chosa. ; Chikyu kankyo kanren kenkyu doko no chosa (nisanka tanso no kankyo fuka teigensaku ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    1992-03-01

    The paper studies the measures for reduction of environmental load of CO2 from the standpoint of chemical technology. As for methanol synthesis from CO2, accelerating of the reaction using Cu base compound catalyst is reported. Also, CO2 is methanated at high speed by low temperature waste heat using Ni-La2O3-Ru catalyst. Discussions are given on the subject for development of catalyst reaction relating to hydrogen production technology by methane reforming reaction using steam or CO2. Synthesis of polymetric materials by use of CO2 is also described. The paper mentions that it is indispensable to design high-function electrode and elucidate the reaction mechanism of electrochemical CO2 reduction for electrochemical and photochemical CO2 reduction measures. Moreover, in case of using solar energy, it is required to study photovoltaic excitation process in semiconductor electrode/ electrolyte solution interface. For production of hydrogen from CO2 by photosynthetic organisms and solar energy, the problem is control of inhibiting effect of oxygen combinedly produced. Described are production of polyhydroxy butyric acid and biodegradable polymer from CO2 and hydrogen by bacteria, and CO2 fixation imitating the enzyme reaction. 267 refs., 79 figs., 32 tabs.

  13. Fiscal 2000 survey report. Refuse-fueled power generation introduction technology, etc. Part 2. Survey of general refuse-fueled power generation; 2000 nendo chosa hokokusho. Haikibutsu hatsuden donyu gijutsu chosa to - Ippan haikibutsu hatsuden chosa Part 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Surveys were conducted of the effect on waste quality of the Law for Promotion of Sorted Collection and Recycling of Containers and Packaging, diffusion of PFI (private finance initiative) involving refuse-fueled power generation, recycling of slag, etc. Questionnairing was conducted for the survey of the effect on waste of the effectuation of the recycling law, size of population supplying the waste and the amount actually incinerated, actually measured data of the composition of incinerated waste, assorted collection programs, amount reducing measures, and the like. Studies were made as to if the empirical formulas applied in the survey of the preceding fiscal year would remain applicable after the coming into force of the recycling law. In the survey of PFI popularization, it was found that the rate it was taken into account for concrete projects was so low as 13.8% though most of the autonomous bodies had cognizance of PFI. It was requested that it be clearly stipulated that 'the conventional subsidies and grants apply also to PFI projects.' In the survey of conversion of residue into molten slag in refuse-fueled power generation and its reuse, four kinds of slag specimens were examined for physical properties, elution, and analyzed for ingredients, and then it was found that they posed no problems like heavy metal elution. (NEDO)

  14. Fiscal 1997 survey report. Feasibility study of the environmentally friendly type coal utilization system (survey of the coal utilization in Pakistan); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Pakistan ni okeru sekitan riyo gaikyo chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper made a literature survey, hearing survey, site survey/study on the coal in Pakistan such as the coal utilization system and the environmental situation, etc., and aimed at pre-examination for the survey of the introduction of the environmentally friendly type coal utilization system to be planned in Pakistan in the future. The examination, data collection and preparation were conducted in terms of the following items: the structure of coal consumption in energy supply, structure of coal consumption, mainly of domestic brown coal consumption, the situation of coal utilization by industry and by region, environmental problems caused by coal utilization such as air pollution, the trend of policies of environmental regulation, etc. The literature on the following was obtained and surveyed: the situation of economy/energy in Pakistan, coal utilization technology by industrial field, and environmental protection technology. The hearing survey was made to institutions concerned, corporation groups and men of learning and experience. Site surveys were conducted for the typically selected coal utilization equipment and existing environmental protection equipment. 66 figs., 56 tabs.

  15. FY1997 report on test well drilling and well investigation for the Akinomiya area survey in the geothermal development promotion survey; 1997 nendo chinetsu sokushin chosa. Akinomiya chiiki chosa shisui kussaku koji oyobi kosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In order to extract promising areas with high geothermal feasibility, the Akinomiya area was surveyed by drilling test wells. In the N9-AY-3 excavating work, the first stage (depth from 15 to 33 m) used the water-free excavation to prevent adverse effects on the water sources. The second stage (depth from 33 to 409 m) reached the targeted depth with slanted excavation. The third stage drilled into depths from 409 to 1,006 m. The fourth stage was targeted to drill down to 1,802 m, but an entire lost returns have occurred at the depth of 1,598 m, whereas lost water drilling was performed by using fresh water, and the drilling was terminated at the targeted depth. The AY-4 excavation was also advanced with the first, second, third and fourth stage method, and when the entire lost returns have occurred at 1,196 m, the lost water drilling was carried out by using fresh water, and the drilling was terminated at the scheduled 1,505 m. The AY-5 excavation was also advanced with the first, second, third and fourth stage method. The first and second stages used water-free excavation (using air hammers) to avoid influence on the nearby spa areas. The third stage went down to 405 m performing coring, but the entire lost returns occurred at 298 m. The excavation rate was very high, and the core recovery rate reached 100%. The fourth stage presented the same coring condition as that for the third stage down to 1,002 m. (NEDO)

  16. FY 1992 report on the survey of geothermal development promotion. Geochemical survey (No. A-1 - Haneyama area); 1992 nendo chinetsu kaihatsu sokushin chosa chijo chosa hokokusho futai shiryo. Chikagaku chosa hokokusho (No. A-1 Haneyama chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-05-01

    For the purpose of studying an expanse and characteristics of the geothermal system and a possibility of geothermal development in the Haneyama area, Oita Prefecture, geochemical survey was conducted. In the survey, various kinds of analyses were made for 13 specimens of hot spring water and 5 specimens of surface water in the area of about 280km{sup 2} at 402 measuring points of the concentration of Hg in soil gas. The results of the survey were as follows: In this survey area, it was thought that the HCO{sub 3} type geothermal water of a comparatively low temperature which was heated by the wide-spread conduction heat from the depths was widely distributed deeper than the depth of 500-700m, and it was presumed that a possibility was low of existence of a high geothermal potential which can be used for the geothermal power generation in the part deeper than the drilling depth of 700m. In the Noya area in the southwest part of the survey area, the high temperature deep geothermal reservoir was confirmed. In this area, the high temperature neutral-alkalescent Cl-SO{sub 4} type geothermal water was distributed in the depth of several 100 meters or deeper. The geothermal water seemed to flow from NE to SW along the structure in the NE-SW direction, and it was concluded that the area was the most promising one. (NEDO)

  17. FY 1992 report on the survey of geothermal development promotion. Geochemical survey (Survey of geothermal water) (No.36 - Hongu area); 1992 nendo chinetsu kaihatsu sokushin chosa. Chikagaku chosa (Nessui no chosa) hokokusho (No.36 Hongu chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-07-01

    The test on jetting of geothermal water by the induced jetting, sampling of geothermal water and analysis/survey were carried out in the structure drilling well of N4-HG-2 in the Hongu area, Wakayama Prefecture. The induced jetting of the well was conducted by the Swabbing method up to the total pumping amount of 459.9m{sup 3} that is equal to about 24 times as much as the inner quantity of the well, but it did not result in jetting. The maximum temperature of geothermal water was 65.6 degrees C, pH was 6.6-7.5, electric conductivity was 2,800-2,900 {mu}S/cm, and Cl concentration was 500-700ppm. The geothermal water was classified into the HCO{sub 3} type that is neutral, and the spring quality and liquidity were the same as those of existing hot springs in this area. In the Hongu area, the distribution of new volcanic rocks has not known. The K-Ar age of quartz porphyry intrusive rocks was made about 13Ma, and it was considered that a possibility was low of the rocks being heat sources of geothermal activities. It was also considered that the geothermal water/hot spring water in this area, which originate in the surface water, were heated in heat transfer by magma activities in the deep underground and were flowing forming a small scale of hydrothermal convection system. (NEDO)

  18. Report on the achievements in the Sunshine Project in fiscal 1987. Surveys on coal selection and coal types (Surveys on coal resources for liquefaction); 1987 nendo tanshu sentei chosa tanshu chosa seika hokokusho. Ekikayo sekitan shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The survey purpose is to identify availability of coal resources for liquefaction in major coal producing countries in the Pacific basin area. Therefore, collection is carried out on such data as coal existing conditions, coal qualities, production quantities, and infrastructures on coal mines being operated and projects under development or investigation. Coal samples are collected in wide range and exhaustively unbiased to particular coal fields and mines to acquire data to perform selection and evaluation of coals that can be fed to coal liquefying plants. The present survey was intended to acquire fundamental data for the liquefying coal selection, such as coal existing conditions, natures, and infrastructures for the coal resources, taking up as the survey object countries the State of Alaska, U.S.A. and Indonesia. The coal types as the object of the survey are mainly sub-bituminous coal, and additionally brown coal and partly bituminous coal. The amount of coal deposit as the subject of the investigation is 100 million tons or more as the verified reserve. The subject areas cover coal mines in the State of Alaska, U.S.A. (Northern Alaska, Nenana, Beluga, and Matanuska coal fields), and Indonesia (the Sumatra and Kalimantan islands). The survey items are made up of 14 items (see the coal mine survey tables in JN0040851). (NEDO)

  19. Surveys for promoting development of overseas coals in fiscal 1999. Surveys on international coal situation; 1999 nendo kaigaitan kaihatsu kodoka nado chosa (kaigaitan kaihatsu sokushin chosa). Kokusai sekitan jijo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Detailed surveys were performed on Britain, Germany and Spain being the major coal producing countries in Europe with regard to a general view on the status of energy demand and supply, the status of demand and supply of coal, business institutions, and related policies in each country. The status of demand and supply of coal, and related policies in the three countries may be summarized as follows: In Britain, the ratio of coal accounted for in the primary energy supply is 18.0% in 1998, and the coal production amounted to 35.5 mill.TCE/year; closure of underground mining coal mines is discussed recently; the congress is deliberating re-introduction of the subsidy system which had been once discontinued; in Germany, the ratio of coals accounted for in the primary energy supply in 1997 was 14% in bituminous coal and 11% in brown coal; the quantities of production of bituminous coal and brown coal in 1998 were 41.8 and 50.6 mill.TCE/year, respectively; the number of mines has decreased because of the unification; the subsidy policy is in continuation; in Spain, the ratio of coal accounted for in the primary energy supply was 13.5% in 1997 and the quantity of coal production in 1998 was 12.5 mill.TCE/year; unification of coal operators has not been advanced as far as in Germany; and the subsidy is provided as in Germany. (NEDO)

  20. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of application type novel-structure thin-film solar cell manufacturing technology - Development of static micro-concentrator solar cell manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu (micro shukogata taiyo denchi no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    An acorn type concentrator is a 2-dimensional system and realizes relatively high magnification power, but it requires a special assembly process for modularization because the cells and the concentration system are quite small. Under the circumstances, studies are conducted on a prism array concentrator (PAC) which will demand a smaller burden for modularization. A PAC system is basically a 1-dimensional concentrator in terms of light collection performance. The cell to be attached to one plane in the longitudinal direction of the long triangular prism is so small as 5mm in width, yet it may be as long as 50-100mm, and the conventional flat plate assembly process may be made use of. A concentration efficiency of 82% and a conversion efficiency of 10.9% were obtained from a minimodule with a light intercepting area of 5cm times 4cm. Furthermore, a conversion efficiency of 19.7-21.4% was obtained when a small 5mm-wide cell applicable to a PAC type concentration was used. Since a prism type concentrator optical system will cost much for its molding and strengthening when it is built of glass, inexpensive EVA (ethylene-vinyl acetate copolymer) was utilized as an adhesive filler. (NEDO)

  1. Survey and research on patent and information. Survey of standard terms (Hydrogen energy); Kijun yogo chosa tokkyo joho chosa kenkyu. Suiso energy (kento shiryo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    Collected in this glossary are terms for use in the development of hydrogen energy technologies. This glossary has been compiled, in view of the current situation where terms are used without standardization or distinction in various recent reports and publications relating to the development of hydrogen energy technologies, to prevent confusion and to help enhance research and development under the Sunshine Program. This is a 3-year endeavor that was started in 1979, undertaken by a committee consisting mainly of men of learning and experience representing organizations associated with the Sunshine Program. The terms are collected from research achievement reports and other materials covering the period of fiscal 1974-1979 relating to hydrogen energy projects under the Sunshine Program. Approximately 200 terms were picked up in the first fiscal year, and 85 in the second fiscal year. Attached to each of the Japanese terms are the pronunciation, a corresponding English term, and a brief explanation in the Japanese language. (NEDO)

  2. Research report of fiscal 1997. Basic research on the commercialization of innovative energy technologies; 1997 nendo chosa hokokusho. Kakushinteki energy gijutsu no jitsuyoka ni kansuru kiso chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper summarizes the research result in fiscal 1997 from the basic research results on the commercialization of innovative energy technologies. The target of a photovoltaic power generation market includes isolated power sources (several kWp) for distant places or developing countries, and those (several tens kWp) for personal residences or public facilities. Although the former is mainly promoted in the West, while the latter over the world, their profitability is unsolved. Power plants over several hundreds kWp are in demonstration test. Solar heat power generation of several tens to hundreds MWp is most profitable, however, small-scale one is poor in feasibility. Australia takes an interest in distributed photovoltaic power generation directly connected with actual lives of residents, and has a dominant opinion that desert is useless as large-scale site. This country lays emphasis on protection and maintenance rather than positive use of desert based on a basic cognition that desert is easily changed and broken. The Australian government announced power company`s obligation to use renewable energy by 2%, and a strong organization is scheduled to be newly established. 59 figs., 57 tabs.

  3. Initial-stage research report on business of drawing up regional new energy vision for Shibecha Town; Shibechacho shin energy vision sakutei jigyo chosa shoki dankai chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The vision includes (1) the buildup of foundations for comfortable living circumstances by utilizing new energy, (2) the development of local industries that befriend themselves with nature by utilizing new energy, and (3) the practice of education and training on environment through the intermediary of new energy. Concerning item (1), in the construction of public facilities, residential houses, and roads, all of which constitute the foundations of daily life, plans will be promoted to use energy produced by the utilization of natural energy resources such as solar rays, solar heat, and wind force, and other energy produced by utilizing heat from refuse incineration and heat latent in the sewage, for the establishment of comfortable living conditions with CO2 emissions reduced. Concerning item (2), studies will be made to install biogas-utilizing plants for excrement treatment and recycling in dairy and animal husbandry; and wind power generation and small-scale hydroelectric power generation will be introduced for supplying power in connection with the effort to complete programs for constructing resort country sites and public meadows. Concerning item (3), for the development of the eco-museum concept, new energy facilities utilizing solar rays, solar heat, wind force, etc., will be introduced into school buildings. (NEDO)

  4. Fiscal 1992 report. Overseas surveys out of surveys for coal hydrogasification technology development; 1992 nendo sekitan suiten gaska gijutsu kaihatsu chosa ni okeru kaigai chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-12-01

    As part of the coal hydrogasification technology development survey project, overseas surveys were carried out as in the preceding fiscal year. With an emphasis placed on the process materials and resources, and on product utilization technologies, surveys and studies were conducted about the trends of development of coal and natural gas resources, and information was collected on energy-related matters in Indonesia and Australia. The need of hydrogasification technology was investigated from the viewpoint of natural resources. Moreover, Japanese engineers were dispatched to APEC (Asia-Pacific Economic Cooperation Conference) New Energy Seminar, Indonesia. Visits were made for information on the natural gas resources at an LNG base in East Kalimantan, Indonesia; coal gasification, energy, and others at CSIRO (Commonwealth Scientific and Industrial Research Organization), Australia; coal bed and methane resources at Warren Center, University of Sydney, Australia; coal bed and methane resources at the Brisbane office, Mitsubishi Gas Chemical Company, Inc.; and coal resources at coal mines of Idemitsu South Queensland Coal Pty Ltd. (NEDO)

  5. FY 2000 report on the analytical survey of the basic data by area; 2000 nendo chosa hokoku. Chiiki betsu kiso data bunseki chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    From a viewpoint of the spread of energy conservation technology, etc. that Japan owns, following the previous fiscal year, data collection/study were made of 51 countries and 1 area including 49 countries (17 Asian developing countries, 13 Middle East countries and 19 countries in East Europe/Former U.S.S.R.) and 2 countries (Japan/the U.S.) and 1 area (the EU) that were added for comparison with developed countries. Items for study were the general situation, economic/trade indicators, administration/general situation, energy situation, economic/technical cooperation from Japan, implementing situation of NEDO's model project, AIJ implementing situation in each country, etc. To keep the continuity, data were numerically obtained from the same data source as that used in the previous fiscal year as a rule. The input data were made as consistent in each item as possible, and the same table was obtained from a single data source as a rule. The data in the previous fiscal year were reviewed, and the data were adopted from which data on as many countries as possible could be acquired through the same data source. (NEDO)

  6. Basic survey for coal resources exploitation for Fiscal 1998. Coal GIS survey; 1998 nendo seitan shigeh kaihatsu kiso chosa. Sekitan GIS chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the construction of a coal mine assessment technology system, surveys are conducted on the current state and technology trends of resources-related GIS (geographical information system) in other countries. When one ponders over coal-rich areas to be newly explored and developed in one's study on the stable exploitation of coal abroad and its import to this country, what interests one gradually shifts from known superior large-scale coal mine areas to next-generation coal mine areas yet to be exploited. Accordingly, it is mandatory to build an assessment-oriented comprehensive technology system capable of promptly dealing with any changes in natural, geological conditions that may be presented by coal mines to be exploited. Although GIS is recognized as a useful means not only in the field of natural science but also in other fields whose data may be plotted on a map, its position is not yet established when it comes to coal resources. It is therefore necessary to promptly introduce GIS into the field of coal. In fiscal 1998, on-site surveys were conducted not only in Japan but also in the U.S., Canada, and Australia who are senior to Japan in terms of GIS application. Also, information was collected from literature and via Internet, surveys were conducted about the use of GIS in the field of earth science especially in the field of coal resources, and the state of the digital data utilizing setup indispensable for the proper operation of GIS was investigated. (NEDO)

  7. Research report of fiscal 1997. Basic research on joint implementation for preventing global climate changes; 1998 nendo chosa hokokusho. Kyodo jisshi kiso chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research was made to promote Activities Implemented Jointly Japan Program. Joint Implementation (JI) is the methodology for preventing global climate changes by collaboration of countries. The countries take cooperative actions for reduction, absorption and fixation of greenhouse gases, and effectively distribute the reduction credits among relevant parties. This was decided in the first session of the Conference of Parties (COP) held in March, 1995. In COP3, Japan`s assigned reduction amount in 2008-2012 was determined as 6% of the emission level in 1990. The protocol defines JI between parties as dealings of emission reduction units, and JI between developing countries as clean development mechanism. The rules for a base line and credit distribution are necessary before full-scale implementation. Although JI is regarded as an important cost-effective project, it is important to decide where and how the JI projects should been promoted. The present state and issues of the primary approved project of Japan Program are arranged. In particular, various terms related to developing countries remain to be solved. 21 figs., 32 tabs.

  8. Fiscal 1998 research report. Feasibility study on international cooperation for technology transfer; 1998 nendo chosa hokokusho. Gijutsu iten ni kakawaru kokusai kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    CTI (Climate Technology Initiative) is a framework for use by developed countries in international cooperation and voluntary promotion of the development and diffusion of technologies contributory to reduction of greenhouse gas emissions. The CTI's activity goal is to accelerate the transfer and diffusion of technologies for climate change control. As the first step toward personnel development programs relating to energy efficiency, CTI organized its workshop on that theme. The results of the workshop have been examined, and its achievements were reported at COP4 meeting, while responses by participatory countries were studied to evaluate the potential of international cooperation with regard to personnel development for reducing greenhouse gas emissions. In fiscal 1998, the CTI workshop 'Energy Efficiency' was held. The participants from developing countries understood the necessity and importance of energy saving enough through discussions in the workshop, and announced their message toward the world at COP4 meeting. (NEDO)

  9. Report on the achievements in the Sunshine Project in fiscal 1986. Surveys on coal type selection (coal type survey); 1986 nendo tanshu sentei chosa seika hokokusho. Tanshu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-03-01

    The purpose of the present study is to elucidate coal quality features of different types of coals and identify the relationship between the coal quality features and the liquefaction characteristics by performing liquefaction characteristic evaluation tests. Based on the result therefrom, a method is established for coal field assessment that can estimate yield of liquefaction in coal fields and coal mines to serve for selection of coal types suitable for liquefaction. Coal quality feature surveys and liquefaction characteristics evaluation tests under the standard conditions have been completed on 48 coal types including Canadian, Australian and American coals. Elucidating the coal quality features of different coals can specify parameters for the coal quality features related to the liquefaction characteristics. Coal ranks elucidate the vitrinite reflectance, structure constituent factors the vitrinite content, composite factors the volatile matter content, quantity of heat generation, and number of H/C and O/C atoms. Investigating the relationship between the coal quality features and the liquefaction characteristics can provide fundamental data for primary screening of raw material coals for liquefaction. The result of the liquefaction characteristics evaluation test under the standard conditions can be the detailed comparative data relative to data derived from the simplified liquefaction characteristics test that is performed to estimate liquefaction yield of specific coal field and coal mine. (NEDO)

  10. Latest groundwater investigating methods and measuring techniques. 1. ; Investigation on aquifer distribution (investigation method). Saikin no chikasui chosa hoho to keisoku gijutsu. 1. ; Taisuiso no bunpu chosa (tansaho)

    Energy Technology Data Exchange (ETDEWEB)

    Yamai, T [Asia Air Survey Co. Ltd., Tokyo (Japan)

    1993-06-30

    This paper explains groundwater investigating methods, introducing particularly two methods. The resistivity tomography is a method to measure potential distribution generated when current is applied around an area to be investigated. Using the measurement result as projection data, the resistivity distribution is restructured within the area of the investigation. The paper summarizes the measurement method (measuring equipment, electrode arrangement, etc.), the analytic method (establishment of an initial model, and the alpha-center method to calculate theoretical potentials corresponding to the model), and an application example of the method in which the resistivity change was observed using permeation of salt tracers. The resistivity imaging method (two-dimensional resistivity analysis method) is superior in practicability to the above method under the present state of the art. This method does not differ from the conventional resistivity method in methodology, but improves the analytic accuracy over the conventional electrical investigation method as a result of analysis combining the simplified two-dimensional analysis method with the alpha-center method. A summary is given on the measuring and analyzing methods. 13 refs., 10 figs.

  11. Fiscal 1998 research report. Survey on energy consumption in a residential sector; 1998 nendo chosa hokokusho. Minsei bumon energy shohi jittai chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    On energy consumption in a residential sector, the report reports the document survey result including new documents, and the result of the systematic national questionnaire survey carried out in small and medium cities to prepare the basic data for future development and introduction of petroleum substituting energy. The electric power consumption rate of detached houses (A) is larger by 0.6- 1.6Gcal/household/year than that of apartment houses (B) in every district. The gas consumption rate of A is smaller than that of B in Hokkaido, Kanto and Kyushu. The LPG consumption rate of Kinki district is largest in both A and B. The kerosene consumption rate of A is larger than that of B. In Hokkaido, the kerosene consumption is extremely large in heating, showing a ratio of 60% or more in A. In the other districts, the kerosene consumption is largest in hot water supply, showing 30% or more. Every consumption rate increases with annual household income. The average consumption rate of 4 districts is 11,137Mcal/household/year. (NEDO)

  12. Fiscal 1990 report. Overseas surveys out of surveys for coal hydrogasification technology development; 1990 nendo sekitan suiten gaska gijutsu kaihatsu chosa ni okeru kaigai chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-12-01

    For the selection and evaluation of coal gasification processes suitable for substitute natural gas (SNG) production, visits were made to overseas business corporations, research institutes, etc., engaged in the development of coal gasification technology, surveys were conducted of the status of development abroad, and information was collected. Visited were Westfield Development Center, British Gas plc; Midlands Research Station, British Gas plc; IEA Coal Research; IFP (Institut Francais de Petrole); and DMT-FP (DMT-Gesellschaft fur Forschung und Prufung mbH). The Westfield Development Center uses coal from near-by open cut mines and supplies town gas to the Scottish region. The slagging Lurgi process, etc., were investigated. At Midlands Research Station, where a coal hydrogasification process is under development, the history of development and the cold model test were summarized, a test plan using a 5 tons/day pilot plant and the modification of test facilities were explained, and the 5 tons/day pilot plant was visited for study. (NEDO)

  13. Technical surveys on MHD combustors. Surveys on incorporation of pressurized coal partial combustion furnaces; MHD combustor gijutsu chosa. Kaatsugata sekitan bubun nenshoro no donyu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    The pressurized coal partial combustion (PCPC) furnace is surveyed/studied for its incorporation in MHD generation. The technical development of the atmospheric CPC has been basically completed, and the concept is demonstrated using a test system of commercial size. Many techniques developed for the atmospheric CPC are applicable to the PCPC system. These include structures of the CPC furnace walls, and slag handling and simulation techniques. Combination of PFBC with PCPC or IGCC can bring about many merits, e.g., enhanced efficiency and abated NOx emissions for the combined cycle power generation. These topping cycles, therefore, should be developed in the early stage. MHD power generation is one of the concepts that can enhance efficiency. In particular, the techniques for closed cycle MHD generation have notably advanced recently. The PCPC techniques are useful for coal combustors for MHD generation. Full-scale development works for the direct coal combustion gas turbine systems have been just started for the IGCC systems of the next generation, and the PCPC-related techniques are expected to serve as the central techniques for these turbine systems. (NEDO)

  14. Report on the FY 1998 survey for preservation of Jozankei Hot Spring. Hot spring variation survey; 1998 nendo Jozankei onsen hozen chosa. Onsen hendo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    Of the FY 1998 survey for preservation of Jozankei Hot Spring, a survey was conducted with the aim of grasping the state of variation in ingredients of hot spring, etc. in the area and of elucidating the causes of hot spring variation. During the period from October 27, 1998 to August 28, 1999, the following were carried out: sampling of specimens of spring water at 6 spring sources, river water at 2 points and precipitation at 2 points; measurement of temperature, spring temperature, pH, electric conductivity, etc.; analyses of Na, Ca, CL, HCO{sub 3}, SiO{sub 2}, etc. The results of the analysis are as follows. As to spring sources, A-2, A-7 and B-1, the precipitation or river water flow rate seem to largely affect the variation in hot spring measuring values. As to spring resources, A-6 and B-4, the relation with the precipitation or river water flow rate is not clear, but a big change is recognized in the snow-melting season. The tendency to the two variations seems to be caused by the difference between the spring with which the river water is greatly concerned by the crack system of the spring having reached the river and the spring which was closed on the earth surface. The temperature variation of springs was considered to be affected by the river water which flowed into the springs. (NEDO)

  15. Research report. Environmentally friendly energy community research business for Fujieda district (Refuse energy utilization); Fujieda chiku kankyo chowagata energy community chosa jigyo (haikibutsu energy riyo shisetsu) chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    An environmentally friendly refuse energy utilizing business, for which RDF (refuse derived fuel) produced out of wastes discharged by industries belonging to a Fujieda city environmental protection council will provide the heat source, is proposed by the said council. The proposal is subjected to a study, a basic plan is drafted, and a decision is made on its profitability. In the study, surveys are conducted on the actualities of wastes and of demand for heat, and specifications are worked out relating to transportation and storage of RDF, production of steam by an RDF-fired boiler, routing of pipes for transmitting the steam to the industries in the district, facility costs, operating costs, etc. It is found that the amount of RDF produced out of the wastes discharged by the council member industries is so small that it can meet the demand of only one industry and that, even if more wastes are collected from a wider area, the increased amount will but meet the demand of two industries and a hot water pool. It is found that the system will be economically feasible, however, if the shortage of RDF-generated energy is covered by an oil-fired boiler and thereby impartiality is established in steam distribution and steam production unit price is reduced. In view of the intensification of control over dioxin, etc., the business will be gaining profit in 2002 and after. (NEDO)

  16. Survey report for fiscal 2000. Survey on lifelong education system for chemical engineers; 2000 nendo chosa hokokusho. Kagaku gijutsusha shogai kyoiku system chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective to identify social needs for continuous education of chemical engineers, a questionnaire survey was performed on member corporations and research institutes in chemical industries. The result of the survey revealed that, among the 1,032 replies, about 60% of the corporations are conducting the continuous education systematically, and 73% is planning to continue it into the future. With regard to its implementation, about 70% of them use the combination of in-house and outside educational organizations, while in using the outside organizations, expectation toward academic societies is as overwhelmingly high as about 60%. Themes of the seminars include the 'latest waste water treatment', 'latest air pollution preventing technologies', and 'latest industrial wastes recovery and treatment technologies' occupying the top three ranks, followed by the 'safety evaluation' and 'safe design' indicating high interest in environment and safety. For engineer ethics, planning and personnel departments showed as high interest as about 80% or higher, but it is about 60% in manufacturing departments. It was revealed that academic societies in Europe and America are paying efforts in the continuous education of member engineers, which, in turn, contribute to financial bases of the academic societies. (NEDO)

  17. Fiscal 1998 research report. Research on energy conversion technology using biomass resources; 1998 nendo chosa hokokusho. Biomass shigen wo genryo to suru energy henkan gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Feasibility study was made on construction of the new energy production system by thermochemical conversion or combination of thermochemical and biological conversions of agricultural, fishery and organic waste system biomass resources. This report first outlines types and characteristics of biomass over the world, proposes the classification method of biomass from the viewpoint of biomass energy use, and shows the introduction scenario of biomass energy. The energy potential is calculated of agricultural waste, forestry waste and animal waste as the most promising biomass energy resources, and the biomass energy potential of energy plantation is estimated. The present and future of biochemical energy conversion technologies are viewed. The present and future of thermochemical energy conversion technologies are also viewed. Through evaluation of every conversion technology, the difference in feature between each conversion technology was clarified, and the major issues for further R and D were showed. (NEDO)

  18. FY1998 survey of overseas coal import base arrangement promotion. Survey of the international coal situation; 1998 nendo kaigaitan yunyu kiban seibi sokushin chosa. Kokusai sekitan jijo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The paper summarized in a fixed form the coal situation of the major coal producing countries (exporting countries) in the world and major European countries. The survey outlined general circumstances, economy/industry/trade, etc. of each country. As to the coal relation, described are coal reserves, production/supply-demand/export, properties of the main brands, the mining industry law, foreign investment control, working custom, etc. In Part 1, the paper selected the following as coal exporting countries: Australia, Canada, China, Columbia, Indonesia, New Zealand, Poland, Russia, South Africa, the U.S., and Venezuela. In Part 2, the paper described coal trends in the main European countries such as France, Germany, the U.K., and Spain, in terms of maps, general circumstances, main economic indexes, changes in imports/exports, imports/exports from/to the main countries, trade configuration by item, recent energy policy and coal policy, changes in coal supply/demand and future, coal-related governmental organizations, etc. (NEDO)

  19. Report on the survey of geothermal development at Okushiri Island, Hokkaido. Geochemical survey (Finger print method); Hokkaido Okushiritou chinetsu kaihatsu chosa chikagaku chosa (Finga print ho) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-07-01

    The geochemical survey by the finger print method was carried out in the Okushiri Island area, Hokkaido, and places of fracture existence were extracted and districts of possible geothermal existence were estimated. The finger print method is a geochemical survey method of soil gas, and the soil gas was collected along the main roads and mountain streams at measuring intervals of 100-300m. The gas collector was buried 30cm deep from the ground surface for 17 days, and the soil gas that rose from deep underground was adsorbed/accumulated into activated carbon. The gas analysis was made by the high sensitivity Curie point pyrolysis/quadrupole mass spectrometer. As a result of the survey analysis, the existence of fracture zone was presumed in the district along the Shiromizusawa that is a branch of the Horonai River, district along the road of the Okushiri Island line and district 1.5km WSW from the 5.8K Pass. Further, out of all 12 specimens, 6 specimens of Type X were distributed in a group in the district 1km square in north, south, east and west with the top of Mt. Shokan almost as the center. The possible existence of geothermal reservoirs was presumed. (NEDO)

  20. Survey of regional new energy vision formulation for Shimizu town. Report on initial stage survey; Shimizucho chiiki shin energy vision sakutei chosa. Shoki dankai chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    Shimizu town, Hokkaido, is a 11,000-strong town, located in the northwestern part of the Tokachi plains and consuming 1.7 times 10{sup 4} Gcal in energy. Discussion is held for new energy which will make the most of the local characteristics of the town while the basics of town building are considered and confirmed. The results of the survey are summarized in four chapters which are (1) the purpose of regional energy vision formulation, (2) local characteristics, (3) state of new energy in existence, (4) and the course to follow for the introduction of new energy (draft). Chapter (4) is constituted of the purpose of new energy introduction and the basic policy, and the course along which new energy will be adopted. Proposed in relation with the course of new energy introduction are the effective utilization of biomass resources, utilization of cold heat energy (ice) involving agriculture, introduction of a symbolic small scale water energy system, introduction of a symbolic wind energy system, extensive introduction of solar energy, and the deployment of popularizing and enlightening activities. A project is mentioned of experimentally introducing biogas facilities that makes use of farm animals' excretion. (NEDO)

  1. FY 1999 basic survey of coal resource development. Coal GIS survey; 1999 nendo sekitan shigen kaihatsu kiso chosa. Sekitan GIS chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The purpose of this survey is to construct a comprehensive coal field assessment technology system which can promptly cope with any natural conditions/geological situations of coal field. As to the GIS (geographical information system) which can unifiedly manage/analyze various data being used in other fields, survey was conducted of present situations/technology trends of the resource related GIS, and at the same time the survey is aimed at applying it to the coal resource field. In the survey in this fiscal year, based on the survey made in FY 1998, applicability of GIS function was verified for Australia where the coal GIS is prepared. And the fundamental design was made to construct a coal GIS considered of concrete application in the stage of coal resource exploration and resource assessment. In the fundamental design, prototypes of individual functions of the system were made. Making the analysis using the actual data, expansion and complication of the system size were advanced step by step toward the completion of the system. Such prototypical development method was adopted. (NEDO)

  2. Research report of fiscal 1997. Survey on strategies of export of environment technology in overseas countries; 1997 nendo chosa hokokusho. Shogaikoku no kankyo gijutsu yushutsu senryaku chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For active environment technology export to OECD countries, needs for environmental measures in developing countries were surveyed. Both collection of environment technology needs in developing countries and preparation of technology seeds information of Japanese enterprises, and promotion of environmental projects by adding an information dispatch function are important. Active preparation and exchange of experiences and know-how of concerned enterprises, local governments and national organizations are also necessary. For development and possible export of small- and medium-sized ventures with excellent technologies and know-how, a suitable consulting system is essential for risks. For smooth promotion of warming prevention by international cooperation, active development of monitoring technology is also important. To support developing countries, OJT of persons in charge in technology transfer sites, and preparation of information infrastructure are necessary. Japan with much know-how on environmental preservation should positively participate in international standardization activities such as ISO. 10 refs., 14 figs., 56 tabs.

  3. FY 2000 report on the analytical survey of the basic data by area; 2000 nendo chosa hokoku. Chiiki betsu kiso data bunseki chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    From a viewpoint of the spread of energy conservation technology, etc. that Japan owns, following the previous fiscal year, data collection/study were made of 51 countries and 1 area including 49 countries (17 Asian developing countries, 13 Middle East countries and 19 countries in East Europe/Former U.S.S.R.) and 2 countries (Japan/the U.S.) and 1 area (the EU) that were added for comparison with developed countries. Items for study were the general situation, economic/trade indicators, administration/general situation, energy situation, economic/technical cooperation from Japan, implementing situation of NEDO's model project, AIJ implementing situation in each country, etc. To keep the continuity, data were numerically obtained from the same data source as that used in the previous fiscal year as a rule. The input data were made as consistent in each item as possible, and the same table was obtained from a single data source as a rule. The data in the previous fiscal year were reviewed, and the data were adopted from which data on as many countries as possible could be acquired through the same data source. (NEDO)

  4. Fiscal 1997 report on a feasibility study of international joint researches in the Asian region; 1997 nendo chosa hokokusho (Asia chiiki kokusai kyodo kenkyu kanosei chosa (4)hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    It is thought that the energy consumption in Asian countries with ASEAN and China as center will a marked growth also in future together with a rapid economic growth, but harmony with environmental problems and economic growth is being taken as a serious problem. This is an important issue also to Japan from viewpoints of secure energy supply and regional response to the environmental issue. Accordingly, strongly desired is positive response to global environmental issues and promotion in development/spread of new energy/energy conservation in these countries. For the spread of the technologies, actual construction/operation of plants by joint researches with Japan are effective from aspects of personnel raising, technical improvement, PR effects, etc. This is also helpful for Japan in terms of technological development because Japan can also get the unobtainable data from the operation under appropriate conditions. This is a report on the studies of the trends of global environmental problems in Thailand, Indonesia, Malaysia, the Philippines, India and China. 3 figs., 72 tabs.

  5. Fiscal 1998 research report. Feasibility survey on offshore wind power generation in Japan; 1998 nendo chosa hokokusho. Nippon ni okeru yojo furyoku hatsuden no donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This survey studied the feasibility of large-scale offshore wind power generation in Japan. Attempt was also made on preparation of outline maps of offshore wind around Japan. The cost of future offshore wind power generation systems is roughly dependent on technical issues and environmental issues. As technical issues, 'installation site,' 'foundation,' 'system interconnection' and 'maintenance/management' were summarized based on applications in Europe. As a result, it was clarified that technical issues can be solved with existing technologies to a certain extent, however, those relate to economical problems closely. The previous environment impact assessments say that wind power generation has no problems on the environmental issues. As relatively strong wind coastal areas, the outline maps of offshore wind point out Western Hokkaido area, Japan Sea area of Tohoku district, Pacific ocean area of the central part of Honshu, Genkai Nada area, Western Kyushu area and Southwest islands area, and suggest that these areas are promising for offshore wind power generation. (NEDO)

  6. FY 1997 report on the field survey on country situations including efficient energy consumption. Vietnam; 1997 nendo chosa hokokusho (energy shohi koritsuka nado chiiki josei genchi chosa). Vietnam

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Field survey was made on the current state of and issues on energy in Vietnam. In Vietnam, firewood is in wide use as non-commercial energy, and sums to a half of total energy consumption. Other energies such as hydroelectric power, petroleum, natural gas and coal are self-sustainable. Commercial energy consumption in 1995 is estimated at 10,070,000t in oil equivalent, which is broken down into 23% for coal, 42% in oil, 5% for natural gas and 30% for electricity. Abundant water resources will form the mainstay of future electric power supply. Commercial production of oil started in 1986 becoming an oil exporting country. Several promising natural gas fields were discovered as the result of the exploration by foreign capital. Coal deposits are estimated to be nearly 3.5 billion tons, and most of them are anthracite. Electric power demand is growing at a higher rate than the economic growth of Vietnam. The growth rate of electric power demand is set to be 1.3 times that of GDP. Since construction funds for new plants cannot be satisfied with the national budget and domestic investment alone, the country is expecting foreign capitals. 21 figs., 36 tabs.

  7. Fiscal 1997 report on the investigational research on intelligent social infrastructure technology; 1997 nendo chosa hokokusho (chiteki shakai kiban kogaku gijutsu no chosa kenkyu hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper first described an aim and outline of intelligent social infrastructure technology, summed up the system of social infrastructure and the situation in Japan in terms of the structure, lifeline, moving bodies such as railroad and automobiles, communication, security, and maintenance. Considering this present situation, the paper next described a concept of the intelligent social infrastructure technology to be newly constructed and a course of the development. Besides, as subjects required to study for the development of intelligent social infrastructure technology, it reported on risk management, methods of definition/collection/transfer/supply of information, infrastructure applicable at emergency, normal/emergency dual course system, privacy, robustness, and additionally the problems to be caused pertaining to architecture/civil engineering, traffic, security, communication, etc. when the infrastructure develops as a social system. Moreover, as element technology, the intelligent system related technology and data communication technology were described in detail. Examples of the research project were also reported. 101 refs., 70 figs., 42 tabs.

  8. FY1997 geothermal development promotion survey. Development feasibility study 'Ashiro area'; 1997 nendo chinetsu kaihatsu sokushin chosa. Kaihatsu kanosei chosa (Ashiro chiiki) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-01

    With regard to the Ashiro Town area in Iwate Prefecture, this paper reports the result of evaluations based on temperature and pressure logging after a lapse of an extended period of time (well No.2) and a steam jet test (well No.1). These activities were performed as the survey on promotion of geothermal development and survey on development feasibility in fiscal 1997. As a result of the overall analysis based on the present survey and ones in the past, the geothermal system model in the surveyed area may be conceived as follows: in both of the N7-AR-1 and N7-AR-2 wells drilled in the southern part of the surveyed area, temperature as high as 250 degrees C or higher was confirmed; the underground temperature is 200 degrees C or higher at an altitude level of zero meter and 250 degrees C at around -500 m, leading to a belief that the high temperature area spreads to south; as a fracture system holding geothermal fluid, a fault was identified at the N7-AR-1 well drilling depth of 1710 m; in the steam jet test, a geothermal reservoir (a shallow geothermal reservoir) was confirmed to exist; the geothermal fluid that has jetted out shows alkaline Na-SO{sub 4} type; and the deep geothermal reservoir has high temperature and is presumed to be in the two-phase condition, presenting promising factors as the geothermal resources. (NEDO)

  9. Survey report for fiscal 2000. Survey on lifelong education system for chemical engineers; 2000 nendo chosa hokokusho. Kagaku gijutsusha shogai kyoiku system chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective to identify social needs for continuous education of chemical engineers, a questionnaire survey was performed on member corporations and research institutes in chemical industries. The result of the survey revealed that, among the 1,032 replies, about 60% of the corporations are conducting the continuous education systematically, and 73% is planning to continue it into the future. With regard to its implementation, about 70% of them use the combination of in-house and outside educational organizations, while in using the outside organizations, expectation toward academic societies is as overwhelmingly high as about 60%. Themes of the seminars include the 'latest waste water treatment', 'latest air pollution preventing technologies', and 'latest industrial wastes recovery and treatment technologies' occupying the top three ranks, followed by the 'safety evaluation' and 'safe design' indicating high interest in environment and safety. For engineer ethics, planning and personnel departments showed as high interest as about 80% or higher, but it is about 60% in manufacturing departments. It was revealed that academic societies in Europe and America are paying efforts in the continuous education of member engineers, which, in turn, contribute to financial bases of the academic societies. (NEDO)

  10. Fiscal 1999 research report. Survey on geothermal development sites (Survey on natural environment); 1999 nendo chinetsu kaihatsu sokushin chosa. Shizen kankyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the result on selecting sites for large-caliber production wells, and landscape characteristic evaluation for simulation, based on the landscape survey on C candidate site for geothermal development. Field survey was made on landscape, plants and animals in the Kirishima Eboshidake area. It was clarified that this area has diverse flora including some rare species such as rein orchid and monkshood which are listed as endangered species. In addition, not a few epiphytes were identified. The zoological survey result showed that planted forests of evergreen coniferous trees which cover a wide range of the surveyed area, and peripheral grassland, scrub and natural forests provide good habitats for mammals such as sika deer and wild boars. On the other hand, no animal species in need of special protection were found. Geologically some traces of landslide occurrence in the past were detected in the northern part of the surveyed area relatively. As the survey result, some promising sites suitable for geothermal development were selected, which are judged to have a relatively small impact on natural environment and landscape. (NEDO)

  11. Report on technological trend survey in fiscal 2000. Survey on bio-technology development strategy; 2000 nendo gijutsu doko nado chosa hokokusho. Bio technology gijutsu kaihatsu senryaku chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Survey and research have been performed on bio-technologies as to their seeds of technological development projects to be worked on by the government from the viewpoint of industrial utilization technologies. In the survey on the trends of research and development and technological development on human-genomes, the survey has been done on the status of execution in the Millennium Genome Project, and how the works related to human-genomes are done at the bio-related government based research organizations and the private sector research organizations. Trends related to the human-genome research in overseas countries were also surveyed. With regard to the future prospect of research and development in the post genome age, discussions were given on the result of the questionnaire survey on opinion leaders in the industrial, governmental and academic areas. In discussing the viewpoint of the industrial utilization technologies related to human genomes, candidates assumed usable in the genome related application fields were discussed, and a basic framework of a technological map was prepared. Based on the results thereof, the technological development areas anticipated to be important in the future were extracted, and the technological development themes were discussed. (NEDO)

  12. Fiscal 1991 report. Overseas surveys out of surveys for coal hydrogasification technology development; 1991 nendo sekitan suiten gaska gijutsu kaihatsu chosa ni okeru kaigai chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-11-01

    For the selection and evaluation of coal gasification processes suitable for substitute natural gas (SNG) production, visits were made to business corporations, research institutes, etc., engaged in the development of coal gasification technology abroad, and surveys were conducted of the development status overseas and information was collected. Visits were made and information was collected on the Lurgi process, a commercial SNG plant, and others at Dakota Gasification Company, U.S.; U-gas process and others at Institute of Gas Technology; energy-related matters at U.S. Department of Energy; coal hydrogasification process and others at Midlands Station, British Gas plc; Shell coal gasification process and others at Amsterdam Research Institute, Royal Dutch Shell; coal gasification, high-temperature desulfurization, and others at KEMA, Holland; and IGCC (integrated gasification combined cycle) verification plant with the Shell coal gasification process incorporated thereinto, now under construction at Demkolec. (NEDO)

  13. Fiscal 1999 survey on conservation of Jozankei hot spring. Survey report of hot spring alteration; 1999 nendo jozankei onsen hozen chosa. Onsen hendo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-06-01

    As a part of fiscal 1999 survey on conservation of Jozankei hot spring, a survey was made on the change of water composition in hot springs and rivers for the purpose of elucidating the cause of hot spring alteration. In the survey, sampling and water quality analysis were conducted once a month at four sources and one river point on the upstream side of Tsukimibashi bridge on the Toyohira river and at two sources and one river point between Tsukimibashi bridge and Takayamabashi bridge. Also carried out were sampling and constituent analysis at five points for river water of a wide area. The survey results were as follows. The pattern of change in spring water temperature was recognized such that it tended to rise in summer when river temperature was high and to fall in winter. Spring water temperature rose greatly at the time of higher water level like the thaw in some sources but conversely fell in other sources. The fluctuation trend in PH values was such that they mostly went up in April of snow melting time and in early August of much rain and went down in winter of little rain and less snowmelt. As for electric conductivity and dissolved constituents, it was recognized that the conductivity lowered and that the constituents decreased in concentration, all concurrently at the time of snowmelt and much rain. (NEDO)

  14. Fiscal 2000 survey report. Survey and study of constellation satellites technology; 2000 nendo chosa hokokusho. Konsutereshon eisei gijutsu ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Demands for constellation satellites were surveyed and satellite systems were studied for extracting basic technical tasks relative to constellation satellite systems and for drafting space verification plans. For a constellation satellite system to accomplish its missions, two or more satellites have to be simultaneously navigated. It is assumed that its field of application will cover earth observation, information communication, risk management, disaster prevention, and the like. With such applications taken into consideration, surveys and studies were conducted about the need and marketability of constellation satellites, need of state-level involvement, and requests for missions to be imposed on a constellation system. For plural satellites to satisfy mission requests by coordinating with each other, it will be necessary to develop basic technologies, such as navigational guidance, communications control, system autonomous management, and operation on the ground. Functions and performance that a constellation satellite system are requested to have and basic technologies to be studied and developed were extracted, and space verification plans were drafted. (NEDO)

  15. Fiscal 1998 research report. Feasibility study on international cooperation for technology transfer; 1998 nendo chosa hokokusho. Gijutsu iten ni kakawaru kokusai kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    CTI (Climate Technology Initiative) is a framework for use by developed countries in international cooperation and voluntary promotion of the development and diffusion of technologies contributory to reduction of greenhouse gas emissions. The CTI's activity goal is to accelerate the transfer and diffusion of technologies for climate change control. As the first step toward personnel development programs relating to energy efficiency, CTI organized its workshop on that theme. The results of the workshop have been examined, and its achievements were reported at COP4 meeting, while responses by participatory countries were studied to evaluate the potential of international cooperation with regard to personnel development for reducing greenhouse gas emissions. In fiscal 1998, the CTI workshop 'Energy Efficiency' was held. The participants from developing countries understood the necessity and importance of energy saving enough through discussions in the workshop, and announced their message toward the world at COP4 meeting. (NEDO)

  16. Report on survey of promotion of activities implemented jointly in China in FY 1997; 1997 nendo chosa hokokusho (Chugoku ni okeru kyodo jisshi katsudo no suishin chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Rapid economy growth has been observed in Asia including Japan. On the other hand, problems of population and environment grew even worse with the economic growth. Especially, China is the second CO2 emission country in the world. Large energy demand is still forecasted with its economic growth in the future. It is well-known that the energy consumption per unit GDP is very large. Therefore, it is very significant to promote the activities implemented jointly with China for mitigating the emission of greenhouse gases including CO2, which provides a significant meaning for solving global environmental issues as well as for improving regional environmental issues. It is necessary for the above to recognize the appropriate current situations and to promote the activities implemented jointly suitable for the country. Based on the discussions and information exchanges about environmental issues with staffs concerning environmental policies and scientists as well as the field surveys, methods for the activities implemented jointly were investigated to provide some proposals. 4 figs., 8 tabs.

  17. FY 2000 report on the survey of energy conservation technology in Japan; 2000 nendo chosa hokoku. Nihon kokunai no sho energy gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of supporting self-help efforts to deal with energy environmental problems in developing countries in the Asian region, etc. and making the transfer of the energy conservation technology and petroleum substituting energy technology that are at a practical stage and are owned by Japan, evaluation of each technology was conducted in terms mainly of applicability for a model project. The existing survey data were supplemented/deleted. As the model project supposing the application to developing countries in Asia, types of industry for survey were selected as follows: iron/steel, nonferrous metal, chemical industry, oil refining, ceramics/earthware, paper/pulp, foodstuffs, textile/spinning, electricity (power generation)/gas, technologies common to all industry types. Technologies for survey were energy saving production facilities and energy saving equipment at plant with a regular scale to which the applicability as the model project was supposed. The energy saving effect was all calculated in TOE, and the method to calculate the effect was also described. The paper further described possibilities of introduction/spread of the said technologies to developing countries in Asia, introduction limitation/preconditions, cost vs. effect, etc. (NEDO)

  18. Fiscal 1997 survey report. Survey on the innovative well drilling technology; 1997 nendo chosa hokokusho. Kakushinteki kosei kussaku gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In the geothermal drilling, reduction of the cost of well drilling is an important subject for technical development. The geothermal resource development tends to be made at higher temperatures and at deeper wells. In the present drilling technology, the cost is rising with the exponentially increasing depth and temperature, and there is also occurring the technical limit. Accordingly, the survey clarified the limit of the present drilling technology/cost to point out the research trend of the drilling technology as substitute for the present one, possibilities of the introduction, and the R and D target and subjects. As to latest drilling systems abroad and in Japan, the following were surveyed to study and extract promising technologies and systems: improvement/application of drilling equipment/materials (enhancement of heat resistance of the main drilling equipment, etc., cooling effects of top drive, heat resistance verification of MWD tools, PDM, tricone bits, multi-stage cementing tools, etc.), heightening of drilling rates, trend surveys of slim hole drilling, control drilling, well maintenance/workover, and well design technology. 68 refs., 73 figs., 40 tabs.

  19. FY 1998 annual report on the geothermal development promotion survey. Report on landscape survey; 1998 nendo chinetsu kaihatsu sokushin chosa hokokusho. Shizen kankyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Described herein are results of the natural environment surveys, carried out in the Shitanotai Region in Yuzawa City, Akita Pref., where Geothermal Development Promotion Survey C is scheduled. On-the-spot surveys, conducted from June to November, covered 3 items of landscape, vegetation and animals. The Shimonotai Region has a number of ponds and swamps, some of which are used as fields for Brasenia shreberi, and wet shield plant communities in places reflecting these environments. The zoological survey results show that moderate to dry deciduous forests of Japanese beeches (Fagus crenata) and Mongolian oaks (Quercus mongolica var. grossesserrata) in this region provide sound habitats for large mammalian wild animals, e.g., moon bears (Selenarctos thibetanus). For birds, there are some areas extracted indicating high possibility of being inhabited by honey buzzards (Pernis ptilorhyncus), which are listed as a near threatened species by the Environment Agency. Geologically, traces of landslide occurrence in the past have been detected widely, indicating need for more detailed investigation for land stability. These surveys have extracted several areas whose natural environments and landscapes are damaged relatively little by geothermal development. (NEDO)

  20. Report on fiscal 1998 investigation of Jozankei hot spring conservation and hot spring structure; 1998 nendo Jozankei onsen hozen chosa. Onsen kozo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-10-01

    With the purpose of evaluating recoverable hot water quantity and elucidating the change over a long term, investigations were carried out, with the results summarized, on the geology, alteration zone, gravitational analysis, fluid geochemistry and hydraulics in the area. The investigations covered the area of 7 km x 6 km in about 30 km southwest of Sapporo City and were performed for the period from September 10, 1998 to October 31, 1999. The results were as follows. In the Jozankei area, with the Usubetu layer in the Old Tertiary system as the basement, layers are superposed from the Palaeogene Oligocene to the Quaternary Pleistocene. Distributing in various places between Yunosawa vicinity and Jozankei Hot Spring area are acid to neutral geothermal alteration zones. The hot spring gushing-out zone in the Jozankei hot spring area is supposed to be regulated by side-by-side cracks in the NE-SW direction. It was inferred from tritium concentration and a minor component ratio that, as the mechanism of forming a hot spring, water of precipitation origin circulating and residing for a long time on the Usubetsu layer which is marine sediment is heated by a volcanic heat source latent in the depth. (NEDO)

  1. Fiscal 1998 research report. Feasibility survey on offshore wind power generation in Japan; 1998 nendo chosa hokokusho. Nippon ni okeru yojo furyoku hatsuden no donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This survey studied the feasibility of large-scale offshore wind power generation in Japan. Attempt was also made on preparation of outline maps of offshore wind around Japan. The cost of future offshore wind power generation systems is roughly dependent on technical issues and environmental issues. As technical issues, 'installation site,' 'foundation,' 'system interconnection' and 'maintenance/management' were summarized based on applications in Europe. As a result, it was clarified that technical issues can be solved with existing technologies to a certain extent, however, those relate to economical problems closely. The previous environment impact assessments say that wind power generation has no problems on the environmental issues. As relatively strong wind coastal areas, the outline maps of offshore wind point out Western Hokkaido area, Japan Sea area of Tohoku district, Pacific ocean area of the central part of Honshu, Genkai Nada area, Western Kyushu area and Southwest islands area, and suggest that these areas are promising for offshore wind power generation. (NEDO)

  2. FY 1998 survey report. Examinational research on the construction of body function database; 1998 nendo chosa hokokusho. Shintai kino database no kochiku ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The body function database is aimed at supplying and supporting products and environment friendly to aged people by supplying the data on body function of aged people in case of planning, designing and production when companies supply the products and environment. As a method for survey, group measuring was made for measurement of visual characteristics. For the measurement of action characteristics, the moving action including posture change was studied, the experimental plan was carried out, and items of group measurement and measuring methods were finally proposed. The database structure was made public at the end of this fiscal year, through the pre-publication/evaluation after the trial evaluation conducted using pilot database. In the study of the measurement of action characteristics, the verification test was conducted for a small-size group. By this, the measurement of action characteristics was finally proposed. In the body function database system, subjects on operation were extracted/bettered by trially evaluating pilot database, and also adjustment of right relations toward publication and preparation of management methods were made. An evaluation version was made supposing its publication. (NEDO)

  3. Analysis of output characteristics of PV modules under natural sunlight; Shizen taiyokoka ni okeru taiyo denchi module shutsuryoku tokusei no kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Murai, Y.; Igari, S. [Japan Quality Assurance of Organization, Tokyo (Japan)

    1997-11-25

    The paper measured current/voltage characteristics of various PV modules under natural light and analyzed various characteristics such as generated output and module power generation efficiency. In the experiment, installing various PV modules at the solar techno center located at north latitude 34.7deg and east longitude 137.6deg, measurement was made by I-V curve tracer, pyranometer, and thermocouple buried on the module back. As a result, the following were confirmed: As to the monthly mean power generation efficiency, the crystalline system is lowest in summer and highest in winter, and the amorphous system highest in summer and lowest in winter. Concerning the power generation efficiency and illuminance, the gap of power generation efficiency between at high illuminance and at low illuminance is large in the crystalline system and small in amorphous system. Relating to the azimuth angle of module installation and the generated output, the installation inclined 15deg angle west in summer and 15deg angle east in fall/winter generates more power in the crystalline system. On the contrary, the installation on the south face generates more power in the amorphous system. 4 refs., 8 figs., 3 tabs.

  4. Study of installation of PV systems at campus; Campus ni okeru taiyoko hatsuden donyu ni kansuru kenkyu (taiyo denchi nomi wo secchishita baai no yobi kento)

    Energy Technology Data Exchange (ETDEWEB)

    Tsuboi, N.; Tanaka, H.; Okumiya, M. [Nagoya University, Nagoya (Japan)

    1997-11-25

    In terms of energy consumption, environmentality and economical efficiency in the case of installing the photovoltaic power system on the rooftop of the university campus, a comparative study was conducted with other power generation systems. As objects to be comparatively studied, selected were the all-electric type centralized space heating/cooling system, cogeneration system, nighttime heat storage system and centralized system with solar cells installed. The panel area of the PV system is 10,000m{sup 2} on the rooftop and 7,000{sup 2} on the outer wall. About data on solar radiation, average values obtained in Nagoya were used. Assessment was made in terms of energy consumption amount at the time of operation, system COP, emission amounts of CO2, NOx and SOx at the time of manufacturing and operation, initial cost, running cost, etc. As a result of the study, an effect of reducing global warming gas was admitted in the PV system. However, the initial cost of the solar cell panel was high, and the life cycle cost of the PV system was lower than other systems. 1 ref., 7 figs., 3 tabs.

  5. Method for estimation of the spectral distribution that influence electric power of PV module; Taiyo denchi shutsuryoku ni eikyo wo ataeru bunko nissha bunpu no suiteiho

    Energy Technology Data Exchange (ETDEWEB)

    Yamagami, Y.; Tani, T. [Science University of Tokyo, Tokyo (Japan)

    1997-11-25

    A method was proposed for estimating the spectral distribution using air mass, precipitable water, and clear indexes which are generally obtainable, and a comparative study was made between the spectral distribution obtained by this method and the measured data using output power of PV modules, etc. as indexes. When solar light comes into the atmosphere, it dissipates receiving scattering/absorption by various gases and aerosols. Direct light component and scattered light component which arrive at the earth surface become functions of air mass and precipitable water. The wavelength distribution of scattered light in cloudy sky is not dependent upon air mass, but affected strongly by absorption band by steam of clouds. By relational equations considered of these, output power and short-circuit current of PV modules are obtained to make a comparison with the measured data. As a result, it was found that this method estimated the spectral distribution with accuracy. Further, seasonal changes in the spectral distribution were well reproduced. The simulation of the module output in Sapporo and Okinawa brought a result that the output in Okinawa is 1.93% larger than in Okinawa. 5 refs., 5 figs., 6 tabs.

  6. Development of sealed nickel-cadmium battery for linear motor car (Maglev). Linear motor car yo Ni-Cd denchi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kono, K; Yoshimura, H; Yufu, H [Yuasa Corp., Osaka (Japan)

    1993-10-29

    Development was made of a linear motor car use battery which is strong in repetition of quick charging/discharging and characterized as follows: Its volumetric energy density is 42Wh/kg which is 1.3 times as high as the conventional one. It excels in high efficiency charging/discharging characteristics. High tension steel sheet is used for it, which is incombustible. To lighten the weight, paste type electrodes and high yield point materials were used for the positive and negative electrodes, and jar materials, respectively. To heighten the charging/discharging characteristics, used were electrodes heightened in current collecting effect. To lengthening the life, unwoven nylon cloth was used as a separator. Also to heighten the thermal discharge characteristics, the electrodes were made metallic with a fitting of cooling fins. The battery characteristics as tested gave the following result: At a capacity ratio of 100%, the discharging factor cleared its target value of development also with a high discharging voltage. The charging/discharging characteristics hardly fall in the high temperature region. The charging characteristics include quick charging made possible. As a result of cyclic simulation presuming the linear motor car, the fall in capacity per cycle was as good as 1.5%. 11 figs., 2 tabs.

  7. Hydrogen storage alloy electrode and the nickel-hydrogen secondary battery using the electrode; Suiso kyuzo gokin denkyoku to sorewo mochiita nikkeru/suiso niji denchi

    Energy Technology Data Exchange (ETDEWEB)

    Ono, T. [Furukawa Electric Co. Ltd., Tokyo (Japan); Furukawa, J. [The Furukawa Battery Co. Ltd., Yokohama (Japan)

    1997-02-14

    With respect to the conventional nickel-hydrogen secondary battery, pulverization of the hydrogen storage alloy due to repetition of charging-discharging cycles can be prevented by using a fluorocarbon resin as a binder in manufacture of the hydrogen storage alloy electrode; however, the inner pressure increase of the battery in case of overcharging can not be fully controlled. The invention relates to control of the inner pressure increase of the nickel-hydrogen secondary battery in case of overcharging. As to the hydrogen storage alloy electrode, the compound comprising the hydrogen storage alloy powder as a main ingredient is supported by a current collector; further, the compound particularly comprises a fluororubber as a binder. The nickel-hydrogen secondary battery equipped with the hydrogen storage alloy electrode can control the inner pressure increase of the battery in case of overcharging, and lessen decrease of the battery capacity due to repetition of charging-discharging cycles over long time. The effects are dependent on the use of the fluororubber as a binder which has good flexibility, and strong binding capacity as well as water repellency. 1 tab.

  8. Study on hydrogen storage alloy for NiMH EV battery; EV yo NiMH denchi no suiso kyuzogokin ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kanemoto, M.; Tanaka, T.; Furukawa, K.; Watada, M.; Oshitani, M. [Yuasa Corp., Osaka (Japan)

    1998-10-30

    We have developed a high performance hydrogen storage alloy (MH alloy) suited to NiMH batteries for EV use. During the course of the development, the effects of alloy composition and structure (B/A ratio in AB{sub 5}) on cycle life and high-rate discharge of MH electrodes were investigated using mainly SEM, XRD, TEM analysis. It was found that Co content and B/A ratio (5.1/5) of MH alloy have significant effects on corrosion resistance and high-rate discharge at low temperature. Further, the surface treatments of MH alloy with weak acids and hydrophobic agents were effective for improving the initial activation and for depressing the cell internal pressure build-up. (author)

  9. Hydrogen storage alloy for battery, manufacturing method and nickel-hydorogen secondary battery; Denchiyo suiso kyuzo gokin, sono seizo hoho oyobi nikkerusuiso niji denchi

    Energy Technology Data Exchange (ETDEWEB)

    Inaba, T.; Sawa, T.; Inada, S.; Kawashima, F.; Sato, N.; Sakamoto, T.; Okamura, M.; Arai, T.; Hasimoto, K.

    1997-04-08

    The invention relates to a hydrogen storage alloy for a battery which has a high electrode capacity, and particularly can realize a long battery life. The hydrogen storage alloy of the LaNi5 type with the general formula: ABx is used in the invention. Here, A comprises La, Ce, Pr and Nd, and La and Nd in A account for 70 to 90 wt % and less than 5 wt %, respectively; B is at least one of the elements selected from Ni, Co, Fe, Cr, Mn, Cu, Al, Ga, Si, Ge, Bi, Sn, In, P, V, Nb, Ta, Mo and W; x shows the atomic ratio in the range, 4.5{<=}x{<=}5.6. Since rare earth elements constituting the alloy, and types and compositions of the elements substituting Ni are properly determined, the hydrogen storage alloy for a battery with excellent hydrogen storage characteristics and corrosion resistance is obtained. When the alloy is used as an anode material, the battery capacity is expanded, the alloy pulverization and deterioration are prevented. 3 figs., 1 tab.

  10. Prismatic lithium/thionyl chloride cells, EP series''. Kakugata enka thionylter dot lithium denchi EP series''

    Energy Technology Data Exchange (ETDEWEB)

    Kogure, M.; Ide, M.; Mizutani, M. (Japan Storage Battery Co. Ltd., Kyoto (Japan))

    1990-06-25

    This paper reports on a new type lithium-thionyl chloride cell of high safety. Its structure and characteristics are summerized as follows: first, a porous solid of carbon black, that is the positive electrode, including electrolyte solution of SOCl {sub 2} occupies central part of the interio of a prismatic case made of a stainless steel plate, that is the negative electrode, and a thin plate of lithium covers the inner surface of the steel plate, a glass fibre layer being placed in between the lithium plate and the carbon black solid; second, the cell continues to discharge at constant voltage (3.6V) until its life finishes, for instance, for over 10 years when connected to a risistor of 150k {omega}, third, the cell is effectively used at temperatures between {minus} 55 and 85 centigrade; fourth, the cell is preserved for a long duration without scarcely suffering in its efficiency, its capacity decrea-sing at the rate of 0.5 - 1.0% per year; fifth, the cell does not burst, catch fire or explode even if it is short-circuited, swing violently and then fallen from a height of 1.9m to concrete floor, crushed and, in particular, heated in various ways (it is so de-vised that SOCl {sub 2} vapor escapes through the glass seal adjacent to the positive terminal at temperatures about 160 centigrade). 2 refs., 10 figs.

  11. Shunt and series resistance of photovoltaic module evaluated from the I-V curve; I-V tokusei kara hyokashita taiyo denchi no shunt teiko to chokuretsu teiko

    Energy Technology Data Exchange (ETDEWEB)

    Asano, K; Kawamura, H; Yamanaka, S; Kawamura, H; Ono, H [Meijo University, Nagoya (Japan)

    1997-11-25

    With an objective of discussing I-V characteristics when a shadow has appeared on part of a photovoltaic module, evaluations were given as a first stage of the study on saturation current, shunt resistance and series resistance for the solar cell module. As a result of measuring change in amount of power generated in a sunny day with a shadow appearing over the solar cell module, reduction in power generation capability of about 23% was verified. In other words, the I-V characteristics of the solar cell module change largely because of existence of the shadow caused on the module. The I-V characteristics curve may be expressed and calculated as a function of the shunt resistance and series resistance. By curve-fitting measurement data for a case of changing insolation without existence of partial shadow, values of the shunt resistance and series resistance were derived. As a result, it was found that the calculations agree well with measurements. It was made also clear that each parameter shows temperature dependence. 6 refs., 10 figs., 1 tab.

  12. Temperature dependence of the early degradation in a-Si solar cells; Amorphous Si taiyo denchi no shoki rekka no ondo izonsei

    Energy Technology Data Exchange (ETDEWEB)

    Takahisa, K; Kojima, T; Nakamura, K; Koyanagi, T; Yanagisawa, T [Electrotechnical Laboratory, Tsukuba (Japan)

    1997-11-25

    Discussions were given on early degradation in up to about ten minutes in amorphous silicon solar cells. The experiment has used a model cell of single junction layer for power use with a Glass/ITO/P-i-n:a-Si/Al structure. Test samples were annealed at 130 degC for 30 minutes to eliminate hysteresis of degradation during storage. Xenon was used as an irradiation light source, and the temperatures were varied from 0 to 100 degC and the measurement time was set to 0.1 to 500 minutes. The result of the experiment may be summarized as follows: with regard to time-based degradation pattern for conversion efficiency, the tilt of a pattern to express degradation rate varies with temperature conditions, and changes in 10 to 20 minutes of light irradiation as a boundary; in long-term degradation after 20 minutes, the higher the environmental temperature, the lower the degradation is suppressed, but the rate of initial degradation up to about 10 minutes is higher as the higher the temperature; and the degradation rate increases as the higher the temperature in the initial degradation of about 10 minutes, whereas, corresponding to this fact, it is estimated that a phenomenon is involved, in which carrier recombination defect may increase. 4 refs., 7 figs., 1 tab.

  13. Concentration characteristics and cell arrangement in luminescent concentrator PV modules; Keiko shukogata taiyo denchi module no cell haichi to shuko tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Inamura, A [Science University of Tokyo, Tokyo (Japan); Sakuta, K [Electrotechnical Laboratory, Tsukuba (Japan)

    1997-11-25

    A luminescent concentrator PV module requires no tracking equipment and can use scattered light. A mini PV module was prepared from a luminescent plate of 100times100times3mm, and a single-crystalline PV cell of 100times20mm. Characteristics of various prototype modules with different PV cell areas and cell arrangements were also measured. Four kinds of edge reflecting materials with different reflectances by various white coating were applied to Al sashes for module frames, and each sash was fixed on one edge of the luminescent plate. In experiment, 3 other edges were covered with black tapes to reduce each reflectance to 0%. Although PV module output was affected by reflectance of edges, the output was satisfactory at 90% or more in reflectance showing no difference in output. A concentrating efficiency decreased with an increase in luminescent plate (concentrator) area, while it was improved by cell arrangement with short optical pass length, and cell arrangement hardly affected by edge reflection. 4 refs., 7 figs.

  14. Control method for light deterioration of amorphous solar cell. 2. Temperature effect method; Amorphous taiyo denchi no hikari rekka yokuseiho. 2. Ondo kokaho

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, H; Itsumi, J; Sano, N [Kumamoto Institute of Technology, Kumamoto (Japan)

    1997-11-25

    Experimental studies have been carried out on suppressing early deterioration in amorphous silicon solar cells. The amorphous silicon solar cell is characterized by deterioration due to light irradiation and restoration due to temperature rise. An exposure experiment was performed under three conditions: installation in natural environment, installation with rear side of the solar cells covered with an insulating material, and installation with rear side of the solar cells covered with warming elements and an insulating material. Tests were made on suppressing progress of the early deterioration caused by temperature conditions. As a result, the efficiency in the natural condition was found to decrease as largely as 32% in an open circuit condition and 58% in a short circuit condition. The efficiency reduction rate was smaller in the open circuit condition when the insulation material was installed, but in the short circuit condition, resistance characteristics caused by rain water and electrolytic corrosion were exhibited. For the case with warming elements installed, the reduction in the efficiency was more remarkable, contrary to the expectation. The cause was determined that water existing between the rear side and the warming elements was warmed up, accelerating the electrolytic action, and resulting in deterioration advanced over a wide area in the rear side. 6 refs., 6 figs., 3 tabs.

  15. Sony Co., Ltd.: An outlook is made for merchandising of the manganese acid lithium ion battery; Mangansan richiumuion denchi no shohinka ni medo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-31

    Sony Co., Ltd. sells the manganese acid lithium ion battery that a battery is 1 by 2 as to the next generation lithium ion during 99 years. It is characteristics that a price is restrained because manganese is used for the proper pole material instead of cobalt of the rare metal. It becomes mass production by Koriyama factory where a lithium ion battery is being manufactured improving an existent production line. It is seen when some percents of manufacture cost goes down more than cobalt acid battery of news file before. A manganese acid lithium ion battery uses manganese acid lithium for the proper pole of the battery. The efficiency of the charge of the usual lithium ion battery is good, and composition is easy, and uses cobalt acid lithium, which is easy to produce. One side where a material fee is cheap, the stability at the high temperature of manganese acid is low, and composition is difficult. Only NEC Moli Energy corporation who is the subsidiary company of NEC succeeds in the mass production. NEC Moli Energy corporation is extending market share by the price competition power. It seems to have the possibility that manganese acid becomes the main force with a battery by two by new entering of Sony Co., Ltd. of the lithium ion battery extreme big enterprises. (translated by NEDO)

  16. Indirect solar-pumped laser diode using a solar cell; Taiyo denchi wo mochiita taiyoko kansetsu reikigata handotai laser no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kanamori, Y.; Yugami, H.; Naito, H.; Arashi, H. [Tohoku University, Sendai (Japan). Faculty of Engineering

    1996-10-27

    This paper describes the operating characteristics of a stabilizing circuit using commercial electricity, those of a stabilizing circuit using solar cells, relation between the quantity of solar radiation and the maximum output of a semiconductor laser diode (LD), and simulation results of annual LD output in Sendai City. The stabilizing circuit for the solar-cell driven LD was structured such that the output of the solar cell panels was guided to a DC/DC converter, that the voltage was set at a prescribed value and that the current was stabilized with the use of power MOSFET. The solar cells used in the experiment were monocrystal silicone solar cells with the maximum output of 53W each. In the experiment, the LD was protected by stabilizing the current at a set value when an excess current was supplied to the stabilizing circuit. As a result of the simulation of the annual LD output from the meteorological data of Sendai City, it was predicted that a solar cell of approximately 1kW was able to provide an annual output of 102MJ and that the efficiency was highest with four sheets of the solar cell. Consequently, consistency proved to be essential between the LD and the solar cell output. 3 refs., 7 figs.

  17. Control method for light deterioration of amorphous solar cell. Temperature effect method; Amorphous taiyo denchi no hikari rekka yokuseiho. Ondo kokaho

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, H.; Yokoyama, S.; Itsumi, J. [Kumamoto Institute of Technology, Kumamoto (Japan)

    1996-10-27

    This paper describes a proposed method for suppressing light deterioration (temperature effect method), in which an annealing effect was always expected by laminating an NEM element and a heat insulation material on the back side of a-Si solar cell module and thereby raising the temperature in the back side of the module, and also describes an outdoor exposure test device completed for the method. The NEM element consisted of conductive potassium titanate and high molecular polymer and was a self temperature-controlling organic exothermic body that required no outside temperature control device. It was provided with a heat generating temperature of 45-75{degree}C as the exothermic property of the element and capable of generating heating temperature arbitrarily according to the purpose. The NEM element varied a resistance value against the ambient temperature and kept the element temperature constant. Measurement was commenced starting April 19, 1996, using the completed outdoor exposure test device and a measuring circuit. The deterioration phenomenon was and from then on continuously examined under the following conditions: (1) measurements were those of clear days only, and (2) measurements to be used were those between 10:00 and 14:00 with the quantity of solar radiation on a constant level. 4 refs., 4 figs., 1 tab.

  18. Development of measurement device for evaluation of solar cell module output. 2; Taiyo denchi module shutsuryoku hyokayo sokuteiki no kaihatsu. 2

    Energy Technology Data Exchange (ETDEWEB)

    Minoda, M.; Itsumi, J. [Kumamoto Institute of Technology, Kumamoto (Japan)

    1996-10-27

    Enhancement in design efficiency may be attained as well as utilization in maintenance if on-the-spot data is made available, for the purpose of flexibly dealing with changes in design or matching with a house structure, in calculating the power generation output of a solar cell (PV) module. Under the circumstances, a small-sized compound measuring device was produced as a prototype which, using an I-V curve tracer, measured output and condition of a roof at the time of installation, compared with the optimum operation and predicted the power generation. The device was structured with the main body consisting of a computing part, measurement controller and power supply and with various sensor modules. The electron load control method was employed in order to measure I-V characteristics of the PV module, since it was desirable to use a variable load and to cover the range from the release voltage of a solar cell to the short-circuit state through the maximum output point. The reference module method was used for the system evaluation. The device was presumably applicable to a PV system design by incorporating a sensor module for measuring design environment data, which was essential at the time of a system design, in addition to those for measuring output. 9 refs., 4 figs., 3 tabs.

  19. Effect of PV module output power on module temperature; Taiyo denchi no shutsuryoku henka ga module hyomen ondo ni oyobosu eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Hongo, T; Kitamura, A [Kansai Electric Power Co. Inc., Osaka (Japan); Igaki, K; Mizumoto, T [Kanden Kako Co. Inc., Osaka (Japan)

    1996-10-27

    Effect of the photovoltaic (PV) module output power variation on the module surface temperature has been investigated by field measurements. PV modules with capacity of 54 W were used for the temperature measurements. Three 2 kW-class PV systems were operated. T-type thermocouples were used for measuring temperatures. Measurement time intervals were 15 minutes, 30 minutes, 60 minutes, and 24 hours. Measurement period was between May 25, 1995 and June 25, 1996. The surface temperature increased during non-loaded PV output, and decreased during load-carrying PV output. Difference of the surface temperature between non-loaded PV output and load-carrying PV output was 3.5{degree}C at maximum through a year. The surface temperature was saturated within 30 minutes. When PV output was changed in 30 or 60 minutes interval, the variation of surface temperature was distinctly observed. When PV output was changed in 15 minutes interval, it was not observed distinctly. There was no difference of the surface temperatures during the time zones with less solar radiation, such as in the morning and evening, and at night. Except these time zones, difference of the surface temperatures was 3.5{degree}C at maximum. 4 figs.

  20. Study on property-gradient polymer electrolyte for rechargeable lithium batteries; Lithium niji denchi no tame no keisha tokusei kobunshi denkaishitsu no sosei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kokumi, Z; Kanemura, S; Inaba, M; Takehara, Z; Yao, K; Uchimoto, Y [Kyoto University, Kyoto (Japan)

    1997-02-01

    This paper describes the fundamental experiments for creating property-gradient polymer electrolyte for rechargeable lithium batteries. The rechargeable lithium battery is composed of an anodic composite agent section with high ion conductivity, a separator equivalent section with high mechanical strength (high bridging degree), and a section surpressing the precipitation of metal lithium by contacting with it. The continuous property-gradient polymer electrolyte was tried to be synthesized by means of the plasma polymerization method. As a result, plasma polymerization electrolyte with high ion conductivity could be prepared from the liquid phase by using a monomer with low vapor pressure. Porous material simulating the anodic composite agent was impregnated by the monomer, which was plasma-polymerized. As a result, it was found that the bridging degree decreased from the surface towards the inside of the plasma-polymerized porous material. In addition, polymer was prepared using fluorine-base monomer. Thus, LiF thin film could be prepared through the reaction between the polymer and metal lithium. 3 figs.

  1. Needs/seeds research committee of welfare apparatus; Fukushi kiki needs seeds tekigo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    As to the development of welfare apparatus, a study was made on the present status of the periphery environment, problems, measures and policies. As subjects in production, the following were pointed out: small scale of the market, lots of brands/small quantity of production, various corporate sizes in the industry, no competition among countries, modular structuring, etc. As to the standardization, the necessity was asserted for the following: rationalization of production/consumption, security of product quality, provision of standards for accurate judgement of the purchase, simplification of inspection under the Pharmaceutical Law, benefit systems. In relation to evaluation/technical guidance, details of the evaluation, persons involved in the evaluation, and the evaluation form were arranged including not only the evaluation of individual tools, but grasp of the needs, selection of themes, and technical guidance under the development. The fundamental development of the welfare apparatus is being conducted in universities, national research institutes, etc., and necessities were pointed out for a study of trial use of the apparatus as a step next to the prototype making, and a system to support makers for the period from after the development up to the commercialization. 5 refs., 8 figs., 26 tabs.

  2. Faults survey by 3D reflection seismics; Sanjigen hanshaho jishin tansa ni yoru danso chosa

    Energy Technology Data Exchange (ETDEWEB)

    Tsuchiya, T; Ejiri, T; Yamada, N; Narita, N; Aso, H; Takano, H; Matsumura, M [Dia Consultants Company, Tokyo (Japan)

    1996-10-01

    This paper describes fault survey by 3D seismic reflection exploration. Survey has been conducted mainly at flat land area without pavement not in urban area in Japan. Subsurface structure is complicated with intersecting multiple faults. In this area, a lot of geological investigations have been done prior to the seismic reflection exploration. Fairly certain images of faults have been obtained. However, there were still unknown structures. Survey was conducted at an area of 170m{times}280m in the CDP range. Measurements were carried out by using 100 g of dynamite per seismic generation point combined with 40 Hz velocity geophones. Fixed distribution consisting of lattice points of 12{times}12 was adopted as an observation method. In and around the lattice, a great number of explosions were carried out. The CDP stacking method and the method of migration after stacking were used for the data processing. The 3D structures of six horizons and five faults could be interpreted. Interpreted horizons were well agreed with the logging results. 3 figs.

  3. Investigational report on the trend of control technology; Seigyo gijutsu doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    For the purpose of corresponding to changes of the industrial structure and making full use of the control technology, the paper investigated the state of the application. High-grade automation in the manufacturing industry has reached the spread of use at big companies for these 10 years. The hierarchical structure of business/process/DCS has been completed, and the optimal control and the advanced control have been realized. The development and spread to the much wider field is anticipated. The soft structure system is needed for equipment improvement in view of the life cycle of equipment and toward the elimination of bottlenecking. For the design of the control system, commercial tools began to be much used, and it is expected in future to accumulate and recycle the knowledge/knowhow for effective design work. Further, strict simulation models based material balance and heat balance have also been on the rise, and the advance in technology is expected. Because of the total productivity of the production equipment, the control technology is anticipated not only for the pursuit of controllability but for the use as supporting technology in the operation/driving/failure diagnosis for working out, carrying out and evaluating the optimum operation plan. 18 refs., 99 figs., 100 tabs.

  4. Research report on human media; Human media no chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The human multimedia technology corresponding to users` subjective characteristics was researched to realize information environment producing a sense of unity with human. The human media technology realizes a human sensitive information processing model and a common database easily acceptable sensitively by various users. This technology also should be able to fairly accept and transmit individual`s information and knowledge as multimedia information, and in addition it is required to supply a virtual space with presence. In fiscal 1995, the research committee studied the concrete developmental issue for integrating these advanced fundamental technologies, and as practical images planned the prototype systems such as human media interactive plant operation, supply of environment supporting personal intelligent activities, and virtual medical center. The research committee also discussed development of space mobile media to secure energy-saving and safety of automobiles, and an environment simulation system with participation of many people. 34 figs., 2 tabs.

  5. Investigation on food sanitation controlling technologies; Shokuhin eisei kanri gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    Doi, Y [Hokkaido Electric Power Co. Inc., Sapporo (Japan); Nishioka, J

    2000-03-24

    Investigation has been made on the current status of food sanitation controlling technologies. Eighty percent of food poisoning is caused by bacte such as Salmonera, enteritis vibrio, staphylococcus, and pathogenic colibacillus. Putrefaction as the cause for food poisoning occurs from proliferation of different microorganisms. Heating sterilization is the main method being performed, but non-heating method may include sterilization by flash and high voltage pulse discharge in addition to ultra-high pressure and ultraviolet ray sterilization. As a result of the questionnaire survey, what is extracted as the problems in the food sanitation controlling technologies is to establish a rinsing and sterilizing method with large sterilization effect, an effective sterilizing method and thawing of processed marine products, and a cooling method in food processing. Increasingly demanded for the future is to develop a foodstuff sanitation control system using as the core the hazard analysis critical control point (HACCP, a quality control program developed by the U.S. NASA to ensure safety in manufacturing space food), and micro-organism control and sterilizing technologies to support the above system. The flash pulse and high-voltage pulse sterilizing technologies as the non-heating sterilizing technology are more effective than the conventional heating sterilization methods also from the aspect of quality retention after sterilization. More active development thereof is desired. (NEDO)

  6. Report on an analytical survey on the Pacific energy information; Taiheiyo energy joho bunseki chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    For the purpose of collecting and arranging energy information in the Asia and Pacific region, this survey has been conducted for many fiscal years. The Asia and Pacific region is classified into the Chinese area, the Southeast Asia area including Brunei, Indonesia, the Philippine, Singapore and Thailand, the East Asia area including Japan, Korea, Taiwan and Hong Kong, the North America area including the U.S. and Canada, and the Oceania area including Australia and New Zealand. As to the primary energy supplied from 1980 to 1993, China largely increased its share by 3.1%. The Southeast Asia also increased its share by 2.1%, and the East Asia by 2.5%. To the contrary, the North America area largely declined its share by 7.8%, but still has approximately 60% in the Asia and Pacific area. By kind of energy, coal increased the share while oil decreased. 16 figs., 7 tabs.

  7. Feasibility study of Copahue geothermal development project, Argentina; Aruzenchin kyowakoku Copahue chiiki no chinetsu kaihatsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    Abe, M.; Yamada, M.; Nakanishi, S.; Todaka, N. [Electric Power Development Co. Ltd., Tokyo (Japan); Fujita, T.

    1996-03-15

    Geothermal resources have been evaluated in the Copahue district. For this survey administrated by JICA, drilling of a deep test well with a small bore (COP-3) and blowout tests were conducted. This district is located at the east side of the Andes elongated in the N-S direction. Volcanoes with similar active periods and active states are distributed in the N-S direction, which forms a divide with the Pacific Ocean side. The Copahue-Caviahue composite volcano in the surveyed area is located nearly in the central part of the volcanic zone, which forms a special ring topography. Geology of the Copahue district consists of volcanic effusive rocks during the Tertiary and Quaternary periods. There are five prospecting fields with geothermal indications in the surveyed area. From the survey, an area of about 13 km{sup 2} was evaluated as a geothermal resource field. Especially, in the area of about 4 km{sup 2} including COP-1, 2 and 3 wells, the steam predominant type reservoirs were found out. As a result of estimation of the geothermal resource potential by the volumetric method, a highly prospective power generation potential of 30 MW was evaluated in the field where the steam predominant type reservoirs were confirmed by the boring wells. 7 refs., 13 figs., 1 tab.

  8. Ground water contamination by electrical prospecting; Denki tansaho ni yoru chikasui osen chosa

    Energy Technology Data Exchange (ETDEWEB)

    Irie, S; Fujii, Y; Sakaguchi, S; Ushijima, K [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1996-05-01

    A report is made about the result of vertical electric sounding conducted in the MK district, Fukuoka City, where Kyushu University is about to move. As for the method of electrical prospecting, in consideration of the need for probing a depth of 50m at the shallowest, vertical electrical sounding with a Schlumberger array of electrodes was employed. Measurements were made for 57 locations on the planar ground, the interval between electrodes gradually increased from 1 to 200m. In the 2D structure model analysis, a 2D inversion program was utilized in the ABIC minimization method. Also investigated were the relationship of electric prospecting and the geology, geological conditions, water level in the well, water quality, salt water, and pore rate from the previously-conducted investigative boring. As the result, it was estimated that the boundary between the first and second layers detected by electric prospecting reflected the level of underground water and that the boundary between the second and third layers reflected the portion where the N-value sharply increases. 4 refs., 8 figs.

  9. Survey of technological trends in functional membrane materials; Kinosei makuzai ni kansuru gijutsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1979-03-01

    Materials for membranes with novel functions are surveyed. The survey is focused on 10 subjects, which are high-performance RO (reverse osmosis)/UF (ultrafiltration) membranes; development of an energy-efficient secondary treatment system for urban wastewater using pollution-free membranes; high-performance ion exchange membranes; artificial lung membranes; hydrogen separation membranes (hydrogen as energy); development of an energy-efficient combustion system using gas separation membranes (oxygen-enriched membranes); organic matter separation membranes; enzyme-aided chemical reaction membranes and their application; development of a distilling ship; and functional membranes making use of photosynthesis. Discussed in this connection are the outlines of the technologies, the need of their development, methods and contents of the development efforts, and the effects and impacts of their development. The survey further concerns the particulars of the trends in novel technologies about functional membrane materials development, covering gas separation and liquid separation technologies; chemical reaction membranes; and enzyme-aided chemical reaction membranes and their application systems. As for their application, the survey covers the field of application of desalinated or ultrapure water; field of application of food fermentation technologies; industrial wastewater, valuable materials recovery, and urban wastewater treatment; and application to medical systems. (NEDO)

  10. Fiscal 1998 research report on super compiler technology; 1998 nendo super konpaira technology no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For next-generation super computing systems, research was made on parallel and distributed compiler technology for enhancing an effective performance, and concerned software and architectures for enhancing a performance in coordination with compilers. As for parallel compiler technology, the researches of scalable automated parallel compiler technology, parallel tuning tools, and an operating system to use multi-processor resources effectively are pointed out to be important as concrete technical development issues. In addition, by developing these research results to the architecture technology of single-chip multi-processors, the possibility of development and expansion of the PC, WS and HPC (high-performance computer) markets, and creation of new industries is pointed out. Although wide-area distributed computing is being watched as next-generation computing industry, concrete industrial fields using such computing are now not clear, staying in the groping research stage. (NEDO)

  11. Survey of advanced composite material technology; Senshin fukugo zairyo gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Results of functions and examples are investigated and described for more than 190 fiber reinforced composite materials. There should be a new viewpoint for even the same material when changing the point to observe it, and new industries will be expected if the viewpoint is adequate. This report has proposed a new concept of `composite functions.` The development works based on non-strength functions which will differentiate the other materials have been stressed. After describing the brief history of the advanced composite materials and significance of composite functions, the present situations and future possibilities of such functions as heat resistance, electricity-electromagnetism, chemicals-proof, adsorption, vibration-proof and resistance, tribology, erosion, sound, adaptability to living bodies and etc. have been examined based on the practical examples. As the future important subjects, adapting possibility of materials having composite functions to marine structures, and possibility of water cleaning system are described. 59 refs., 4 figs., 10 tabs.

  12. Econometric analysis on oil-substituting energy; Sekiyu daigae energy keiryo bunseki chosa

    Energy Technology Data Exchange (ETDEWEB)

    1992-03-01

    This is a fiscal 1991 report on the investigation having been carried out for the past 6 years by the Institute of energy Economics contracting with NEDO. The report is to make an overall evaluation of various aspects seen in the development of petroleum substitution energy in relation with the environmental problem. Various kinds of simulations are conducted by developing the industrial related model which can analyse effects of CO{sub 2} emmission control measures exerted on Japan{prime}s microeconomics such as the industrial structure, based on the analytical model which was developed by the fiscal 1990. For example, in establishment of 4 cases such as a standard case, a carbon tax imposition case, an industrial structure arrangement case and a high efficiency-new energy promotion case, signs are seen like that the primary energy supply in 2010 will decrease with heightening of energy price and improvement of consumption efficiency from 740 million kl in crude oil in the standard case to 620 million kl in the high efficiency-new energy promotion case, and CO{sub 2} emission will decrease from 440 million tons to 350 million tons. 14 refs., 65 figs., 114 tabs.

  13. Econometric analysis on oil-substituting energy. Sekiyu daigae energy keiryo bunseki chosa

    Energy Technology Data Exchange (ETDEWEB)

    1992-03-01

    This is a fiscal 1991 report on the investigation having been carried out for the past 6 years by the Institute of energy Economics contracting with NEDO. The report is to make an overall evaluation of various aspects seen in the development of petroleum substitution energy in relation with the environmental problem. Various kinds of simulations are conducted by developing the industrial related model which can analyse effects of CO{sub 2} emmission control measures exerted on Japan{prime}s microeconomics such as the industrial structure, based on the analytical model which was developed by the fiscal 1990. For example, in establishment of 4 cases such as a standard case, a carbon tax imposition case, an industrial structure arrangement case and a high efficiency-new energy promotion case, signs are seen like that the primary energy supply in 2010 will decrease with heightening of energy price and improvement of consumption efficiency from 740 million kl in crude oil in the standard case to 620 million kl in the high efficiency-new energy promotion case, and CO{sub 2} emission will decrease from 440 million tons to 350 million tons. 14 refs., 65 figs., 114 tabs.

  14. Research report of FY 1997 on the clean coal technology promotion project and region model survey. Measures for environmental load reduction: feasibility survey on the environmental load reduction-type utilization Energy Center (interim report); 1997 nendo chosa hokokusho. Clean coal technology suishin jigyo chiiki model chosa `kankyo fuka teigen taisaku: kankyo fuka teigengata sekitan riyo energy center feasibility chosa` chosa hokokusho (chukan hokoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The survey has given an eye to the coal that it can be easily burnt together with combustible waste and supplements unstable generation of waste. Thus, the establishment of the Energy Center at the place where infrastructure of coal will be arranged, a lot of combustible waste will be expected to generate and a considerable aniybt if energy will be used, has been planned, and this survey is intended to study the scale of Energy Center, its economy and the problems to be solved. In power plant project using RDF for above-mentioned local governments, the construction of power plant and the renewal time of the existing incinerator to RDF facility can be planned separately in this system. The power plant will be economically constructed and the amount of coal can be decreased in accordance with increased RDF to meet wide range of refuse treatment. In FY 1997, the actual situation of the waste treatment and the infrastructure of coal supply was surveyed, and selection of the place suitable for the Energy Center and its scale was studied. 69 figs., 50 tabs.

  15. Survey and research on applications of parallel compiler; Heiretsu compiler tekiyorei ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-31

    An urgent proposition is made that an advanced computing software program development and maintenance system be set up, and activities are conducted in search of strategies and guidelines for the establishment of such a system. Out of recognition that it is important to develop software programs such as operation systems for supercomputers, a survey is conducted of software technology development strategies especially involving application software programs. It is proposed that efforts be positively exerted to develop strategic software developing programs for advanced computing for concentratedly enhancing the development now under way of strategic software programs. In concrete terms, named as strategic software programs to be developed are a next-generation semiconductor TCAD (technology computer-aided design) system, protein structure/function analysis system, fatigue simulation system, next-generation fluid analysis system, chemical reaction simulator, grid computing, and a nanodevice surface analysis system. (NEDO)

  16. Report of 'Survey on Asian environmental information networks'; 'Asia kankyo joho network chosa' ni kansuru hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    This project is implemented to survey the current statuses and future trends of the Asian district environment-related information networks, for the (research cooperation project for development of environmental condition measuring laser radar systems), being promoted by NEDO. First, current statuses of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, major domestic nodes and internationally connected conditions are surveyed mainly for internet-connected networks, for surveying the current statuses and future trends of the research networks in Asian countries. Second, current statuses in Indonesia of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, domestic node sites and managing organizations, charge systems and institutions, types/reliability/ stability of the circuits, and conditions of restriction of use, if any, for surveying the current statuses and future trends in Indonesia. Third, conditions of and needs for network utilization by researchers for Asian district environments. (NEDO)

  17. Feasibility study on the introduction of hybrid buses; Hybrid bus donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The purpose of this research is to design pilot projects for introducing hybrid buses into the public transportation sector. This research also covers contents regarding hybrid buses with a trolley-collector motor and a diesel engine, to identify technical and economical problems and to analyze cost beneficiation using hybrid buses. The trolley parallel hybrid system has been employed for the feasibility study. This system has abundant operation results in Europe and the USA. Its battery is small or is not necessary, and the maintenance cost is also low. As a result of the feasibility study, reduction effects of CO2 emission were found out. When the CO2 generation at the power plant is not counted, the reduction effect was estimated to be 32% compared with the CO2 emission from diesel buses. When the CO2 generation at the power plant is considered, it was estimated to be 18%. The cost beneficiation was investigated for the cases of the transportations using trolley system surrounding a medium-scale terminal among large-scale housing development, tourist resort, and stations. The annual income is estimated to be larger than the annual payment in each case. It was found that the hybrid bus is economically established. 17 refs., 48 figs., 41 tabs.

  18. Investigational report on the trend of measures for global warming; Chikyu ondanka taisaku doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    To know the trend of measures taken for global warming, conducted were overseas surveys, participation in academic society meetings, and literature surveys. The phaseout time of all ozone depleting substances responsible for the ozonospherial destruction was determined for both developed and developing countries in the 7th Meeting of countries which concluded the Montreal Protocol. As information on measures for protecting the ozonosphere, introduced was activities under United Nations Environment Programme (UNEP). New fluorine containing ethers were introduced as cleaning solvent which causes no ozonospherial destruction and is low in global warming index. Toxicity data were obtained on HFC-236ea and HFC-236fa which are promising substitutes in HCFC foaming and refrigerant fields. The paper introduced an outline of the 1st Meeting of countries which concluded the Framework Convention on Climate Change held in 1995. According to the report on the National Institute of Public Health and Environmental Protection of the Netherlands, the amount of emission of fluorine containing greenhouse effect gas (in CO2 conversion) reached 8-14% of all the amount of greenhouse effect gas emitted in 1990 unless the control is reinforced. An outline of the TEWI-3 project was introduced which is useful for comparing effects of substitution technologies on global warming. 14 refs., 11 figs., 29 tabs.

  19. Research study on highly functional carbon related materials; Tansokei kokino zairyo no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The study results on highly functional carbon related materials are reported as a part of the leading research in fiscal 1996. Synthesis of these novel materials is outlined, and R & D results on the following materials are described: diamond, hetero-diamond, graphite, amorphous carbon, carbyne, fullerences, carbon nitride and chemically modified carbon materials. Their issues, future possibility and market in 2010 are also described. The markets are predicted of such electronic materials as electronic emitter, sensor, solid device and heat sink, such optical materials as X-ray lithography, and such chemical materials as electrode and catalyst. Promising characteristics of light-weight and high-hardness machine materials are presented, and some issues such as material synthesis, and intensive machining and application technologies are described. The future markets are predicted of their applications to tools, dies, information equipment, glass, automobiles, aircraft, spacecraft and industrial machines. Problems and their break through techniques of these novel materials are also presented. 220 refs., 68 figs., 16 tabs.

  20. Study on the current status of biomass energy development; Bio mass energy no kaihatsu jokyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    A survey was conducted on the present status of biomass energy in Japan and abroad and the developmental trend of the latest biomass energy technology. Brazil and the U.S. are most advancing in the biomass energy utilization. Brazil uses sugar cane which is plenty in supply as a raw material, and the U.S. does corn which is the surplus crop. Both countries use the conventional ethanol fermentation technology and produce the petroleum substitution liquid fuel which is in greatest need. As to the technology to convert biomass resource into energy, attention has so far been paid to the development of the production process of the liquid fuel. The latest technology for ethanol fermentation using saccharin and starch as raw materials has already been established in Japan, and the energy-saving type alcohol recovery technology has also reached the stage of practical application. Moreover, as to the ethanol conversion technology with cellulose substrate, the development of the saccharification process will be needed in future. 15 figs., 10 tabs.

  1. FY 1998 Annual report on researcher exchange project; 1998 nendo kenkyu koryu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Surveys were conducted on, e.g., problems involved in and current state of receiving foreign students and exchanging researchers, and US systems for these activities, in order to help establish the effective systems for these activities while focusing on global utilization of researchers. For problems involved in the atmospheres in Japan for receiving foreign students and researchers, the surveyed items include those problems involved in the academic atmospheres, living/employment, administrative systems, and establishment/enrichment of the systems for receiving foreign students. Opinions of foreign students studying at their expenses are also included. For problems involved in exchanging Asian researchers, the surveyed items include current state of researchers crossing the borders and obstacles to the international exchange. For the US systems receiving foreign researchers and sending American students to foreign countries, the surveyed items include current state of Americans studying in foreign countries, foreign students and teachers in advanced educational institutes, backward flow of scientists and engineers to the Asian countries, and international comparison in training scientists and engineers in advanced educational institutes. (NEDO)

  2. Investigation into the emission of greenhouse effect gases; Onshitsu koka gas no haishutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper grasped the situation of greenhouse effect gas emissions of advanced countries based on the reports from them. The advanced countries which concluded the U.N. Framework Convention on Climate Change (OECD member countries, the former U.S.S.R., and East European countries) are to be reported to the office concerned with work for the framework the situation of their greenhouse effect gas emissions according to the obligation of the framework. In and after April 1997, they made the second report. The paper summarized changes in emission amount, the future trend, and the policies/measures mainly taken of nine countries which have already presented the second report (the U.S., the U.K., Germany, Holland, Italy, Norway, Sweden, Finland, and New Zealand) and one country (Russia) which has made only the first report. Moreover, the literature was collected and summed up concerning the mechanism and coefficients of the emission of nitrous oxide and methane. The collected literature was classified into all fields/plural number of fields, energy relation, industrial process relation, relation with the use of organic solvent and other products, agricultural relation, relation with changes in land use and forests, and waste relation. 4 figs., 228 tabs.

  3. Research report of fiscal 1997. Basic research project on energy saving in developing countries (cooperative research on oil saving / basic research on the industry of Thailand); 1997 nendo chosa hokokusho. Hatten tojokoku energy shohi koritsuka kiso chosa nado jigyo sekiyu shohi koritsuka kyoryoku chosa (Taikoku sangyo kiso chosa hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Field research was made for oil saving in Thailand. To promote energy saving in a textile industry as main export industry, its motivation for production stuff is essential in business improvement. Proposal for work improvement, supply system of bonuses, and small-group activity are effective. Management of an energy consumption rate is essential in business management. Use of efficient waste water treatment equipment is also one of the issues. In food factories, various scopes for improvement are still found by mass/heat balance analysis in production process. As an example, a large amount of water is consumed in vain for washing raw rice in a rice powder factory, and separation of SS precipitate from waste water should be improved. Because of lagoon treatment, an effluent standard is not achieved in spite of consumption of wasteful aeration power. This treatment is reasonable because of its scale and site, although the standard can be achieved by activated sludge method. Reconsideration of the standard is also necessary based on a local total BOD load capacity. The profitability of a methane fermentation method should be examined. 72 figs., 95 tabs.

  4. Advanced technology trend survey of micromachines in Europe; Oshu ni okeru micromachine sentan gijutsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    In this research survey, the development trend of micromachine technology in Europe was surveyed, development level of micromachine technology of European companies was grasped, and practical application fields of their target were investigated. Technology development level of private companies in Japan`s national projects and practical application fields of Japan`s target were arranged. Trends of micromachine technology development are compared between Japanese companies and European companies. Among micromachine technology development projects in Europe, ``8520 MUST`` is a part of the ESPRIT Project. About 40,000 companies among about 170,000 companies in whole Europe are relating to the MUST Project. The main fields include the manufacturing technology, process control of machines, technology of safety, sensor technology in environmental fields, and automotive technology. The marketing fields of application include the automobile, military technology, home automation, industrial process, medical technology, environmental technology, and games. The results can be compared with the direction of research and development in Japan. 22 figs., 8 tabs.

  5. Investigation research on autonomous responsive materials; Jiritsu oto zairyo ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    A survey was made on autonomous responsive materials as a new material which reversibly change molecular structures and the aggregation state according to external stimuli. Autonomous responsive materials imitate environmental responsibility in the living organism system and have sensing, control and active functions for external stimuli. The materials are highly efficient and environmentally friendly. In biomimetic materials for soft actuators, drastic changes by temperature of elastic modulus of water-swollen hydrogel are used to the motion. In order to molecularly design stimulus-responsible polymer gel, studied are the relation between the micro structure and stimulus responsibility, dynamic correlation between the micro structure and the macro structure, etc. In the biomedical field, new cure and diagnosis using innovative materials are expected, and the application of autonomous responsive materials to the field is studied. For example, using hydrogel responding the temperature and the surface and controlling by temperature the interaction with components of the organism such as protein and cells, drug delivery in the organism is optimized. Also studied is the application of hydrophilic/hydrophobic changes by temperature to the chromatography. 215 refs., 47 figs., 11 tabs.

  6. Soil surveying using electromagnetic methods; Denji tansaho wo mochiita jiban chosa

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, I; Kawauchi, K; Goto, N [Muroran Institute of Technology, Hokkaido (Japan); Takahashi, N; Yamada, T [Zukohsya Co. Ltd., Hokkaido (Japan)

    1997-10-22

    Electromagnetic surveying method is applied in Muroran Institute of Technology`s site for power transmission steel towers for the locating of structures buried in the ground and for the study of obstruction to the application of the method. The devices employed are the EM31 and EM38 which are portable conductivity measuring instruments manufactured by GEONICS Company. With the probeable depth in the horizontal dipole mode being approximately half that in the vertical dipole mode, depths of 0.5m, 1m, 3m, and 6m may be explored using the two instruments. In the measurement test, the devices are used to determine a reinforced concrete-made multi-purpose duct that accommodates water pipes, sewers, various electric wires, and heating pipes and is buried at a depth of 2-3m in the ground. In the measurement for a 3m-deep level, a spot high in conductivity due to the reinforced concrete is detected, and the result roughly corresponds to the lay of the duct. In the measurement for a 6m-deep level, no high-conductivity spot is found, meaning there is no such structure at this depth. Although there are some other high conductivity values recorded, they are attributed to manhole covers or steel tower bases on the ground surface. 3 refs., 8 figs.

  7. Survey on development of brown coal liquefaction techniques; Kattan ekika gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-09-01

    Described herein are results of literature survey on brown coal liquefaction reactions and elementary techniques. Liquefaction of brown coal in the presence of CO and steam, or CO, H{sub 2} and steam has been investigated. It is not clear by the literature survey whether it is superior to the normal process which uses hydrogen. Brown coal contains moisture at high contents, and the drying techniques are necessary to be developed for its liquefaction. The future coal liquefaction plant will be much larger than the past one, and there are a number of problems to be solved, such as those involved in the designs of large-sized high-pressure slurry pumps, heat exchangers and preheaters. It is also necessary to develop the materials of and production techniques for large reactors which are serviceable under severe conditions. The solid-liquid separation for liquefaction products involves a number of the elementary techniques characteristic of coal liquefaction processes, and needs many technological developments. The one-stage brown coal liquefaction process is compared with the two-stage process for the secondary hydrogenation of SCR, but no clear conclusions are reached. (NEDO)

  8. Investigational research on welfare equipment needs/seeds adaptation; Fukushi kiki needs seeds tekigo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    At the advent of the aging society, investigated are images of welfare equipment to be developed. In the range where the use of welfare equipment is to be studied, the following are included: self care, excretion, transfer, and support of work other than care, as assistance to daily life; exercise function, communication function, and environment arrangement, as assistance to social participation. Of the images of the welfare equipment classified by the overall evaluation, the following are cited as what supports daily life: a lift usable even in the existing houses, a bump remover by which bumps in the house are removed without making large repairs, a urine collector for females, a training device to prevent urinary incontinence, reduction in the bed-fast elderly, a device to prevent bedsore, a system for safely watching demented old people, a system in which clothes are automatically washed, dried, and hanged on a hanger, etc. What supports social participation are a system for sports experience by virtual reality, sound user interface, etc. For the aged to be healthy physically and mentally, it is essential to be taken good care of and create things to live for by participating the society. For this, it is necessary that the government establish the public policies and that a people be conscious of welfare. 9 figs., 33 tabs.

  9. Investigations on an environmental technology transfer information network; Kankyo gijutsu iten joho network chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    With developing countries (APEC countries) as the main objects, investigations were carried out to issue environmental technology transfer information that Japan has accumulated, and advance exchanges of technical information with persons related inside and outside Japan. As a result of the investigations, it was found that the environmental technology information that serves more effectively for the developing countries is the technical information that has been developed by repeating improvements, has provided actual results in work sites, and is actually used, rather than the state-of-art technologies. Based on this result, business entities having factories and operation centers located in Mie Prefecture and the city of Yokkaichi were asked to provide data for the actually used environmental technologies. Out of 51 items provided by 17 companies, nine items were selected to be used as prototype database materials for an information network. The objects of information sources will be expanded to a nationwide scale in the future to improve the contents of the database. Problems of handling information copyrights and technical know-hows were presented in the course of data collection, urging the necessity of due considerations on the matter. Necessity was indicated on maintenance and management of data base as well as its quantitative expansion. 1 ref., 4 figs.

  10. Survey of the development of industrial technology in Japan; Sangyo gijutsu rekishi keisho chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Conditions for creating Japan`s type technologies have been investigated by extracting technologies and experiences meriting the succession to the next generation among the industrial technologies in Japan after World War II. Technological creativity of Japan began to appear from the 1970`s. Quartz watch of SEIKO, U-Matic VTR of SONY, ladle refinery method of DAIDO Steel, PAN-based carbon fiber of TORAY, continuous annealing of Nippon Steel, calculating machine using liquid crystal of SHARP, ASA-400 high sensitivity film of FUJI FILM, and Japanese word-processor of TOSHIBA are the examples. The basic ability to create those products and technology lays in the diversity of firms in electronic device and fine machinery industries consisting the boundary between general and electrical machinery, the systematizing ability and inter-industrial cooperation which were promoted through quality control, automatization of assembly and production control by computer, and the research and development capability which has been brought up during the high economic growth as a learning process of technology. The society and industries have to make efforts to create the new creative conditions for younger generations. Otherwise, Japan`s technology will not develop. 134 refs., 19 figs., 8 tabs.

  11. Survey of Joint Implementation activities in China; Chugoku ni okeru kyodo jisshi katsudo kanren chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    It is a large task for Japan to positively promote the Joint Implementation activities related to the United Nations Framework Convention on Climate Change. Rapid increase in the emission of greenhouse-effect gases, especially CO2, is predicted in China with remarkable economic growth and population of 1.2 billion. It is essential to promote the Joint Implementation activities in China. In this survey, framework, organization, problems and tasks were investigated to effectively promote the Joint Implementation activities in China. Construction of framework for the real Joint Implementation activities has been proposed. Current problems for promoting the Joint Implementation activities in China are that the distinct guideline for the Joint Implementation is not established in the government, that the receiving system including receiving, planning and arranging sections is not established, and that the burden problems for the costs of project evaluation, data acquisition, monitoring, and verification are not solved. 5 refs., 21 figs., 6 tabs.

  12. Study of the O2/CO2 combustion technology; Sanso nensho gijutsu ni kakawaru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kato, M [Center for Coal Utilization, Japan, Tokyo (Japan); Kiga, T; Yamada, T [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan); Arai, K [Nippon Sanso K.K., Tokyo (Japan); Mori, T [Inst. of Research and Innovation, Tokyo (Japan); Kimura, N; Okawa, M [Electric Power Development Co. Ltd., Tokyo (Japan)

    1996-09-01

    This study is being progressed during a period from 1992 to 1999 as part of the NEDO`s clean coal technology program. This paper describes what has been discussed to date. The absorption method and the adsorption method may be used to recover CO2 as means to deal with the problem of global warming resulted from burning coals. These methods, however, have problems in economy caused from concentration of CO2 in flue gas being low. The present study is intended to raise the CO2 concentration in flue gas by using oxygen plus circulated flue gas in the place of combustion air, so that CO2 may be recovered as it is without being separated from the flue gas. Therefore, an oxygen-blown pulverized coal fired power generation plant having a cryogenic oxygen manufacturing equipment was designed to discuss the plant operability and economy, and the pulverized coal combustion technology by using a dynamic simulation. A large number of findings have been obtained already, and the study has reached a level at which grasping the whole image is now possible. 13 figs.

  13. Research for a database of alternative energy technologies; Miriyo energy ni kansuru data shu sakusei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The paper collects and arranges data on the unused energy in terms of examples of the introduction in Japan and other countries, policies, laws and rules, subsidy systems, etc. In the overview of the system, described was typical heat supply systems utilizing unused energy. As to concrete examples of the introduction in Japan, the examples were arranged by unused energy source, by temperature level, and by region, and a detailed data book of the typical introduction examples was made. As to examples overseas, data were arranged on the introduction mainly in Europe and the U.S. With relation to policies, laws and rules, and subsidy systems in Japan and overseas, investigated were policies, laws and rules, and subsidy systems concerning unused energy mostly in Japan, Europe and the U.S. As to the production quantity, the actual amount of introduction, and the predicted amount of introduction, survey on the effect and arrangement of the data were conducted in terms of typical two heat supply facilities utilizing unused energy. The paper adds information pertaining to the cost, main related companies and groups, the distribution cost, etc.

  14. Survey of agent for intelligent information retrieval; Chiteki kensaku no tame no agent no chosa

    Energy Technology Data Exchange (ETDEWEB)

    Yazawa, T [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1996-09-01

    Development of agent systems has been surveyed, to classify and arrange characteristic functions of the agents, and to grasp the realization situation of these agents in their development. In addition, prospective functions of information retrieval systems using the agents at maximum and functions to be developed among these in the future are clarified. The agents are characterized by the expression function, communication function, planning function, adaptive function, and learning function. The agents are desired to be classified into interface agents whose works are to respond to individual workers, coordinator agents which conduct works with high pervasion, such as assignment of works and their control, and task agents which conduct specialized works for individual examples. Thus, design and configuration of the agent system, and improvement and expansion of system functions can be effectively and easily conducted. 52 refs., 5 figs., 3 tabs.

  15. Survey on the cost of the photovoltaic power system; Taiyoko hatsuden cost chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Comparisons were made of the power generation cost in Indonesia and Thailand between the photovoltaic power system and other power systems. From the difference in technical standards with Japan, trially calculated were the amount of the potential introduction and the possibly reduced cost. In Indonesia, a plan has started for the introduction of a 50W system to 1 million houses in the unelecrified area, but the introduction has not been so promoted as planned. In Thailand, a plan is being carried out for the introduction of the battery charge station system, but the introduction has remained small-scaled. Comparisons were made among the solar home system in Indonesia, the battery charge station system in Thailand, the diesel engine power generation, and the grid connection with the existing power distribution system. The result concluded that the solar home system is low-priced though it depends on the distance from the existing distribution line and the power consumption amount. Moreover, it was found that the system would be more economical than in the case of Japan if obeying international standards for the photovoltaic power system. 6 refs., 15 figs., 56 tabs.

  16. Survey to promote an action implemented jointly project; Kyodo jisshi katsudo project suishin chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    In the 1st (1995) conference of the nations which concluded the Framework Convention on Climate Change, decided on was a trial implementation of an action implemented jointly (AIJ) project with developing countries on the voluntary basis. In the Asia region, emission of greenhouse effect gas is remarkably increasing in accordance with rapid development of economy, and it is important to appropriately support through this project both economic development and energy demand in Asia. Taking the circumstance into consideration, the survey was conducted to contribute to activating the AIJ Japan Program. As the AIJ of leading developed countries, recognized were 25 (U.S.), 6 (Holland), 8 (Germany), 2 (Norway) projects. As to the AIJ in Southeast Asia, China and India, Indonesia is actively participating in the project, but others less actively. Concerning the project needs in every country, heightening of power plant efficiency, enhancement of efficiency in the transportation sector, new energy utilization, recovery of methane gas, etc. acquire a priority. 21 figs., 31 tabs.

  17. Survey of energy load leveling system in Europe; Energy fuka heijunka taisaku ni kansuru Europe chosa

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, Y. [Setsunan University, Osaka (Japan). Faculty of Engineering

    1998-05-05

    This paper describes the survey of energy load leveling systems in Europe. In Denmark, especially regional heating is remarkably diffused, and they have 350 plants. With extending the service areas, the energy load leveling has been promoted. For the cogeneration plants of SK Power, the largest electric power company, they have hot water heat storage tanks for regional heat supply with a total capacity 2,200 MWh. The regional heating system in Goeteborg City of Sweden supplies 80% of the total heat demand of the city. Unused energy sources derived from petroleum refining, sewage treatment, and garbage burning are utilized. In Uppsala, they have seasonal heat storage systems using solar heat. The Vienna Regional Heat Supply Corporation supplies heat equivalent to 5,000 GWh a year. Cogeneration plants and garbage burning plants are used as heat sources, and 25% of the total heating in the city is supplied. In Austria, they have an electric power demand with a peak in winter, and they have a pumped-storage power station in Kaprun for the annual load leveling using dump power in summer. This paper also introduces a compressed air storage gas turbine plant at Huntorf of Germany, and a large-scale underground natural gas storage of Gaz de France. 6 figs.

  18. Survey of selecting the promising drilling points out of the ground survey of the FY 1992 geothermal development promotion survey. Soil gas survey (No.C-1 - Shirotori area); 1992 nendo chinetsu kaihatsu sokushin chosa. Chijo chosa no uchi yubo kussaku chiten sentei chosa (Dojo gas chosa) hokokusho (No. C-1 Shirotori chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    As a part of the survey of selecting promising drilling points, survey was made using soil gas to grasp the area of existence of geothermal fluid in the area for careful examination and the locational distribution of fractures controlling the behavior of fluid. In the survey, the concentration of Hg in soil gas/carbon isotopic ratio of CO2 were measured at 247 measuring points. Generally speaking, there existed the hydrothermal fluid along the structure controlling geothermal activities in the area where the concentration of Hg in soil gas is high, and the volcanic gas as a heating source of geothermal fluid was rising in the area where the carbon isotopic ratio is high. In the survey, areas where both the Hg concentration and the carbon isotopic ratio were high were extracted as promising areas where the high temperature geothermal fluid possibly exists. The promising areas extracted were the periphery of the Daiichi (No.1) Shirotori Hot Spring, periphery of KT-4, southern periphery of N4-ST-2, periphery of 54E-OBN-1 - 54E-OBN-2, and periphery of N4-ST-2. Besides, a possibility of existence of geothermal fluid was indicated in the northeast of N4-ST-1 and in the northeast of KT-9. (NEDO)

  19. Report on the analytical survey of the Pacific energy information; Taiheiyo energy joho bunseki chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Arrangement, investigation and analysis of an energy information exchange system were conducted, with the aim of coping with the development in the whole Asia/Pacific area, the stabilization of energy supply/demand, and the environmental problem and of realizing effective cooperation of every country in the area. Concerning the trend of the domestic primary energy supply/demand, there are some patterns. Countries which show high growth rates are developing countries such as Thailand and China, and NIES such as Korea and Taiwan. Countries where growth rates are slowing down and lowering are developed countries such as Australia, Canada, Japan and the U.S. Countries where energy supply/demand is not stabilized are Singapore, Hong Kong, Indonesia and Chile which are suffering from variations in import/export. The ultimate energy consumption is the domestic primary energy supply from which the conversion loss in the conversion sector was deducted, and indicates almost the same trend as the primary energy supply. It is divided into a stabilized type of developed countries and a rapidly increasing type and a stagnant type. However, there are some exceptions. Total data in the quarter of the year cannot be the yearly data by itself, but requires a year-end tax arrangement. 40 tabs.

  20. Petroleum substitution energy measuring analysis survey; Sekiyu daitai energy keiryo bunseki chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For analytical evaluation of effects of environmental protection measures, energy conservation measures, new energy promotion measures, etc., a very-long term energy supply/demand model was developed and used for a simulational study. The model is composed of the models of macro economics, secondary energy prices, new energy introduction, and energy supply/demand. The feature is that the amount of new energy introduction is measuringly analyzed based on the cost and market scale, and integratedly estimated in a frame of energy supply/demand of the whole Japan. As a result of the simulation, energy source as of 2030 is composed of coal (17%), oil (44%) and nuclear power (15%) in the case of the economic growth as viewed optimistically. Contrarily, in the case of it as viewed pesimistically, energy source is composed of coal (11%), oil (40%) and nuclear power (22%). CO2 emission is -12.4% in the case of the new energy promotion than in the standard case. 7 refs., 79 figs., 107 tabs.

  1. International research on energy conservation techniques; Energy shiyo gorika shuho kokusai chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    In order to utilize energy reasonably over the whole life cycle of products, the life cycle assessment (LCA) was researched including assessment of the quantity of environmental load. LCA is composed of the inventory analysis which analyzes objectively the amount of input and output of all substances and energy due to their gathering, mining, transport, production, use, recycling and scrapping, and the impact analysis to environment based on the inventory analysis. The inventory analysis of refrigerators was conducted. The unit amount of CO2 emission generated by production of materials was estimated on the basis of previous papers. In particular, CO2 emission due to overseas production of imported raw metals reached nearly 80% in Al and 70% in copper. Recycling of materials and heat recovery by combustion of waste were also considered. Environmental effect was next assessed using the inventory data in three stages of classification, characterization and valuation. Although the weight factor of environmental effect is necessary for every emission, European and American data are now used. 59 refs., 68 figs., 81 tabs.

  2. Research report for establishment of NEDO vision; NEDO vision no sakutei ni muketa chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Because of an increase in energy demand due to economic growth and industrial structure change in the Asian area and its effect on global environment, the economic evolution harmonizing with energy and environment (3E) of the Asian area is required. The role of Japan, in particular, NEDO for achieving such 3E was studied from an international viewpoint. The following are thus surveyed: The history of energy demands, economic growth, an increase in energy consumption and their effect on global environment in the Asian area, and the policies, measures and future plans of Asian countries corresponding to the above situations. The role of NEDO is first of all R & D of biomass toward practical use, and development of effective use technology of biomass energy. Positive approach to control of CO2 emission and immobilization of CO2 is also required in industrial and traffic fields. As technology transfer from Japan, promotion of joint researches and establishment of an economic support scheme are expected together with transfer of the basement technology and training. 79 figs., 13 tabs.

  3. FY 1981 report on the Coal Kind Survey Committee; 1981 nendo tanshu chosa iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    For the purpose of establishing coal liquefaction/gasification technology, investigational survey on the usable coal resource in Japan was made to collect/file the data on the state of coal existence, coal kind, etc. by the Coal Kind Survey Committee and the section. In the 1st committee meeting, an idea of the coal kind survey was discussed, and in the 2nd committee meeting, a summary of activities in this fiscal year was reported. In the section meeting, the following were carried out: discussion of a course of the coal kind survey in the 1st meeting; discussion about how to proceed with the coal kind survey/items of data filing in the 2nd meeting; examinational study of items of data filing in the 3rd meeting; summary of activities in this fiscal year in the 4th meeting. As examples of the coal kind survey, the following were cited: special study report on coal resource and gasification/liquefaction characteristics by Science and Technology Agency; results of the survey by Joint Coal Board and Queensland Coal Board in Australia; Report of 1978 by The Fuel Society of Japan; Report of 1976 by Pennsylvania State University; data on process raw coal by The Iron and Steel Institute of Japan, etc. (NEDO)

  4. Investigations on forests from viewpoints of global environment; Shinrin no chikyu kankyoteki shiten kara no chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Forests have become drawing attention as an absorption source of carbon dioxide, a greenhouse effect gas. This paper discusses significance of forests from viewpoints of their roles as diverse ecological systems and socio-economic values. Forest is a place for living and resting of all kinds of living organisms including plants, animals and microorganisms. Living forms in forests being affluent in kinds and large in amount bring great favor to human societies. Forests play diversified roles other than biological roles in addition to largely affecting heat distribution on the ground through evapotranspiration. These roles include suppression of erosion on ground surface, alleviation of micro climate by reducing wind velocity on the ground, and disaster prevention. Forests have an aspect of supply source of production resources for societies as well as an aspect of unused lands. Efficiency of converting solar energy by plants looks inferior to that of solar cells. Biomass may be regarded as regenerative energy limited to a case where excess production is utilized. 142 refs., 56 figs., 44 tabs.

  5. Research on harmonized molecular materials; Bunshi kyocho zairyo ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Harmonized molecular materials (HMM) were researched to create functional materials adaptable to needs such as environmental harmony and high-efficient conversion in post-industrial society and aging society. Superior mechanisms function efficiently in organisms for perception, transmission and processing of information, and transport and conversion of substances. These functions are caused by harmonization between organic molecules, or organic molecule and metal or inorganic substance. HMM is a key substance to realize these functions similar to those of organisms artificially. It is the purpose of this research to develop HMMs, reform production process by innovating separation and conversion technologies, and finally realize molecular chemical plants. This research also develops high-efficient devices to contribute to the information society, and progresses the industry of bio-functional materials such as high-sensitive bio-sensor. The functions, applications and creation technologies of three kinds of HMM such as assembly, mesophase and microporous materials were researched in fiscal 1995. 956 refs., 128 figs., 13 tabs.

  6. Investigation into the situation of technology succession; Gijutsu keisho jokyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The paper made a fundamental investigation to promote historical succession and creative use of the industrial scientific technology. As for the wind power generation, the large-scaling became centralized wind power plants, and the downsizing became the distribution to remote areas. The solar power generation shifted from the thermal power generation to the light power generation. There is also a method to use solar heat directly. As to power systems and the distribution of electric power, the subjects are a combination of energy source, geographical energy transportation, and heightening of consumption efficiency. It was indicated that the subjects changed with a lapse of time under technical/social/systematical conditions, and under the developable energy amount prescribed by those conditions. Heightening of efficiency, which can be realized even by a paper simulation, was realized partly helped by the developing measuring technology. The environmental problem becomes historically severe as a condition of the technical development. However, aimed at was the process where discharged matters and by-products are effectively used and disused matters are not produced. In the coal-thermal power generation, for example, a load of flue gas purification was reduced by the conversion to LNG. 253 refs., 65 figs., 12 tabs.

  7. Survey on econometric analysis of oil substitute energy; Sekiyu daitai energy keiryo bunseki chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    For the econometric analysis of petroleum substitution energy, a domestic econometric model was developed which can concretely and econometrically grasp and analyze effects of measures taken for environmental policies, energy conservation, promotion of new energy, etc. The model was made so synthetic as to catch a relationship between energy supply/demand and changes of econosocial structures in economic growth, industrial structure, life style, etc. which are extremely important elements for catching future energy demand. The model is composed of a secondary energy price model, a new energy introduction model, and an energy supply/demand model. As case parameters, selected were the price of crude oil, introduction of new energy, GDP and energy conservation, and the following cases were assumed: standard case, high price energy case, new energy introduction promotion case, low economic growth case, energy conservation case, and low energy demand case. The results of simulating each of these cases were indicated. 91 figs., 110 tabs.

  8. Coal rank survey committee report for fiscal 1981; 1981 nendo tanshu chosa iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    A coal type research project is started under which data concerning the coal resources that Japan can make use of are to be gathered, which are necessary for determining their fitness-for-use in a coal liquefaction or gasification process, and the gathered data are to be compiled into files which are easy to use. As for the buildup of a computer-aided data bank, since the number of coal types is not yet large, only part of the data is taken into consideration this fiscal year. In the study of compiling the data into files, it is decided that the files be divided into two categories, one for grasping the status of the development project as a whole and the other for defining the positions of the individual coal specimens. Provided in the former are outlines covering the name of coal mine or project, location, entrepreneur, states of the mining area and geology, state of production, infrastructure-related matters, etc. Described in the latter are the details that enable the identification of given specimens such as the coal bed or coal brand, location and method of collection, collector, date, amount of the specimen, method of treatment, etc. (NEDO)

  9. Research study on harmonized molecular materials (HMM); Bunshi kyocho zairyo ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    As functional material to satisfy various needs for environmental harmonization and efficient conversion for information-oriented and aging societies, HMM were surveyed. Living bodies effectively carry out transmission/processing of information, and transport/conversion of substances, and these functions are based on harmonization between organic molecules, and between those and metal or inorganic ones. HMM is a key substance to artificially realize these bio-related functions. Its R & D aims at (1) Making a breakthrough in production process based on innovation of material separation/conversion technology, (2) Contribution to an information-oriented society by high-efficiency devices, and (3) Growth of a functional bio-material industry. HMM is classified into three categories: (1) Assembly materials such as organic ultra-thin films (LB film, self-organizing film), and organic/inorganic hybrid materials for optoelectronics, sensors and devices, (2) Mesophase materials such as functional separation membrane and photo-conductive material, and (3) Microporous materials such as synthetic catalyst using guest/host materials. 571 refs., 88 figs., 21 tabs.

  10. Investigational research on eco-smart engines; Eco-smart engine no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper investigated the trend of research on eco-smart engines into which optimization function of engine performance, high environmental-adaptability, etc. are integrated. The investigation was made in Japan and abroad on technologies of combustion, structure/material, control, design/analysis, systematization, etc. In case of Japan, specifications were established for three types of engines, subsonic, supersonic and hypersonic aircraft, and the research subjects to fulfil the specifications were extracted. In case of the U.S. and Europe, the survey was made of combustion, materials, noise, design concept, control, etc. Important subjects are selected in priority order. Namely, for the enhancement of efficiency, the following were taken up: three-dimensional fiber-reinforced large-size light-weight structure application technology, heat-resistant advanced-material structure damage-tolerant design technology, pseudo-vesicular structure transpiration cooling technology, etc. For the reduction of NOx emission, the paper took up technologies of environmentally optimization combustion, AI combustion control, and non-cooling combustor liner application. For the noise reduction, technologies of new inclination hole orientation noise absorbing structure material application, super noise control, and innovative CFD utilization low noise aerodynamics. Moreover, the results of fiscal 1997 were outlined to indicate the research in the next fiscal year. 14 figs., 10 tabs.

  11. Investigational research on the design of computational materials; Keisanki zairyo sekkei no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Computer chemistry was investigationally studied. The advance of theoretical chemistry is indispensable to the design of materials, and the theory and high speed computational method are expected which can simulate the real system with more accuracy. It is basic to simulate structures and physical properties of structural molecules and the aggregate, but the meso region, the intermedium region between structural molecules and the aggregate, has became regarded as important. Rough visualization models in high polymer materials and the progress of computational software/hardware of quantum chemistry/molecular dynamics such as catalyst become necessary. Seamless zooming is proposed as a concept of the software which simulates materials from micro/macro/meso viewpoints. Moreover, to make the most of computer chemistry, an integrated system is necessary which generally handles computational software, database, etc. For the development of software, indispensable is the demonstrative verification by a combination of experiments and researchers. Under a commission from NEDO, the investigational research was conducted as a leading study during fiscal 1996 and 1997 to view the course of the research. 17 refs., 37 figs., 5 tabs.

  12. Liquefaction induced by earthquakes in Japan. Jiban no ekijoka/ekijoka saigai chosa kenkyu no seika

    Energy Technology Data Exchange (ETDEWEB)

    Tono, I [Nation Inst. for Enviromental Studies, Tsukuba (Japan)

    1992-09-01

    Disaster caused by liquefaction is an important problem for the development of water-front because most of the places suffered from liquefaction disasters recently are located on sandy grounds. The damaged cases in the past due to liquefaction induced by earthquakes are grouped into: subsidence and inclination caused by the loss of supporting force of the ground, coming to the surface of buried structures due to excess pore hydrostatic pressure, destruction of lifeline accompanying the fluidization of ground, breakdown of bulkhead, retaining wall, etc. by increased earth pressure, sinking of soil structures, ground fissure, sliding, and immersion in floods and submergence of farms due to spouting of underground water. As regards prediction of liquefaction, description is made on the prediction of the occurrence of liquefaction and liquefaction prediction for which sedimentation environment is taken into consideration. Open-cut investigation can be said as the most effective means for accurate learning of the depth, thickness and sedimentation structure of liquefied layers. Liquefaction layers found in remains are also introduced. 16 refs., 6 figs.

  13. Survey and research on precision polymerization polymeric materials; Seimitsu jugo kobunshi zairyo ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Survey and research on the precision control of primary structure of polymeric materials and the precision evaluation technology have been conducted to develop advanced polymeric materials. It is proposed that the three basic processes of polymer synthesis, i.e., addition, condensation, and biomimesis, in forming the precision polymerization skeleton are to be covered through a centralized joint research effort with participation of industry, academia, and the government institute and under the leadership of researchers from academic institutions as the team leaders. For the study of technology trends, international conferences held in UK, Germany, and Hawaii are introduced, and domestic meetings, i.e., Annual Polymer Congress and Polymer Conference, are summarized. In addition, Precision Polymerization Forum and International Workshop on Precision Polymerization were held. The basic studies include a quantum-chemical elucidation of the elementary process in polymerization reaction, time-resolved analysis of polymerization process and polymer properties, synthesis of polymers with controlled microstructures by coordination polymerization using metal complexes, synthesis of polymer with controlled microstructures by precision polycondensation, molecular recognition in catalyst-reaction site, and synthesis of imprinting polymers. 246 refs., 117 figs., 14 tabs.

  14. Recent surveys and researches on pollinosis in Japan; Kafunsho ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Shido, T. [The Inst. of Public Health, Tokyo (Japan)

    1998-05-31

    In this paper, recent investigations and researches on pollinosis are summarized as centering on the investigation entrusted by the Ministry of Health and Welfare and executed since 1992, and especially the surveys on Japanese cedar pollinosis during 1995 to 1996. The quantity of pollen surveyed in 1995 is the greatest in the survey history of nationwide flying pollen. Particularly, the quantity of cedar and hinoki pollen is 10 to 40 times as many as that in the year before. Consequently, since the sensitization and onset due to the cedar pollen increased greatly, the objects of the surveys and the researches were mainly in respect to the analysis of onset factors of pollinosis, clarification of its natural process, evaluation on the effectiveness of desensitization therapy, the clinical subjects including the confirmation of pharynx symptom and asthma symptom, and the discovery of naturally sensitizing dog. A fact that the quantity of flying pollen concerns the occurrence and degree of the clinical symptom has already been indicated by a clinical observation carried out for a long period of time. In respect to specific prophylaxis and therapy, for the first time the pollen masks and glasses sold on the market are investigated, and the necessity of the verification thereof is described. 27 refs., 7 figs., 5 tabs.

  15. Metrical analysis survey of petroleum substituting energy; Sekiyu daitai energy keiryo bunseki chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper conducted the modeling on the economic/industrial structure giving the economic frame for energy supply/demand forecast, and made some simulations. In the simulation, assumed were a standard case, aging/hollowing case, and technical innovation case. As to macroeconomic models, macro items such as the economic growth rate, prices and IS balance were determined by giving foreign factors, financial factors, population factors, etc. In long-term energy supply/demand models, data on demand by use in commercial/residential and transportation sectors were estimated using various statistics. About the calculation result of a standard case of the former sector, the existing industries which markedly ebbed are primary products, the material system, construction/civil engineering, etc. Contrarily, the production industry such as general machines, electrical machines and automobiles increased the share. New and highly growing industries are new production industries like electronics and communication and new services like finance, insurance and communication. The GDP rate grows by 2.3% per year on average and lowers in each ten years hereafter. 53 figs., 83 tabs.

  16. Preliminary survey of `Green Recycling System`; Jigyo jizen chosa `green recycle system`

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This report describes the construction of `Green Recycling System` which aims to change deserts to lush lands and to stabilize food supply. A cross-linked polymer produced by irradiating the gooey threads of natto (fermented soybeans) with gamma rays can absorb and hold up to 5,000 times its own weight of water. This biodegradable polymer may be used to develop seed gels and pellets to grow soybean, rice and wheat to improve the productivity of deserts and to protect threatened lands from desertification. This technology will be of great value in establishing stable supply of food resources, especially for the Middle East where deserts are expanding as well as for Africa where serious food shortage is already in place. To undertake the Green Recycling System Project, it is indispensable to develop technologies for producing PGA polymer in large quantity, mass production process of bridged PGA through radiation, chemical cross-linkers, new technologies for growing plants using water retainers, water-retaining materials for arid areas, general systems for growing plants in arid areas, and environmentally benign industrial infrastructures. 76 refs., 59 figs., 29 tabs.

  17. History of technological activities of Japanese industry; Sangyo gijutsu rekishi keisho chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    History of technological activities of Japanese industry has been recorded, preserved, compiled and systematized. The purpose is to make international contribution by transmitting Japanese experience and knowledge to the world, and to bring up the human resource for researches by teaching the history of passion and efforts of the predecessors and by arousing interests and creative volitions of science and technology of young persons. However, memorial matters, data and witnesses relating to the history of industrial science and technology are rapidly being lost day by day. When leaving as it is, succession of the history to next generation becomes hard. Under such a situation, basic survey has been conducted to succeed the history of industrial science and technology and promote the creative utilization of them. This is in the third stage of the survey. This report contains the development of new cold rolled steel sheet for cars, plant engineering technology in Mitsubishi Heavy Industries, electronics, electric power distribution technology in Kansai Electric Power Co., Inc., development of the PAN carbon fibers, four cycle and low speed marine diesel engines, production of electrolytic copper foil, development of jet engines, camera makers, and production of office machinery. 86 refs., 12 figs., 9 tabs.

  18. Feasibility study on the wind farm; Wind farm no kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For assessment of the possibility of the wind farm (collective wind power facility) in Japan, site conditions, business plans and various issues in development were arranged using some projects in a planning stage. The case study of a system design was also conducted for a typical site. Four sites were selected based on geographical conditions, topographic features and weather conditions. Scales of every site are as large as 1000-3000kW and 400- 750kW in wind turbine capacity. Every developer expects a subsidy, and governmental economic support is indispensable for the wind farm. In the case of Hisai city, Mie prefecture with the most favorable wind condition in Japan, the annual mean wind velocity of the site is valued at nearly 8m/s, suggesting that it is promising for the wind farm. From the planned scale of 750kWtimes4, the annual generated power and availability factor are valued at 9,800,000kWh/y and 37%, respectively. From the construction cost of 1 billion yen including a subsidy of its half, the generation cost is valued at 14.5 yen/kWh in durability of 15 years, and 12.2 yen/kWh in 20 years, and the profitability is dependent on the purchase price of a power company. 27 figs., 36 tabs.

  19. Research on the proficient machine system. Theoretical part; Jukutatsu machine system no chosa kenkyu. Rironhen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The basic theory of the proficient machine system to be developed was studied. Important proficient techniques in manufacturing industries are becoming extinct because of insufficient succession to next generation. The proficient machine system was proposed to cope with such situation. This machine system includes the mechanism for progress and evolution of techniques and sensibilities to be adaptable to environmental changes by learning and recognizing various motions such as work and process. Consequently, the basic research fields are composed of thought, learning, perception and action. This machine requires not only deigned fixed functions but also introduction of the same proficient concept as human being to be adaptable to changes in situation, purpose, time and machine`s complexity. This report explains in detail the basic concept, system principle, approaching procedure and practical elemental technologies of the proficient machine system, and also describes the future prospect. 133 refs., 110 figs., 7 tabs.

  20. Survey on the succession situation of technologies; Gijutsu keisho jokyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The basic survey was carried out to promote the succession and creative use of the previous industrial science and technology. The following 5 themes were summarized in fiscal 1993. On `Fuel technology policy and technological development,` Navy Fuel Depot, Chemical Research Institute at University of Kyoto, Central Laboratory of South Manchuria Railway Co., and Fuel Research Laboratory of the Ministry of Agriculture and Commerce played important roles, and the 1000atm continuous hydrogenation system was completed in 1941. On `Technology of long-distance power transmission,` high-voltage insulation technology finally reached an international level after World War II. On `Unification of frequency and electrical technology,` the two-frequency system for eastern and western areas was established before World War II, and construction of Sakuma Frequency Conversion Station allowed power interchange between two areas. On `Organization of national research laboratories,` the Agency of Industrial Science and Technology distinguished the roles of new and existing laboratories. On `Wind power technology in Europe and America,` comparison between American and Danish approaches is the most important issue today. 146 refs., 20 figs., 13 tabs.

  1. Analysis and evaluation for practical application of photovoltaic power generation system. Analysis and evaluation for development of extra-high efficiency solar cells (fundamental research on extra-high efficiency Si solar cells); Taiyoko hatsuden system jitsuyoka no tame no kaiseki hyoka. Chokokoritsu taiyo denchi no gijutsu kaihatsu no tame no kaiseki hyoka (chokokoritsu silicon taiyo denchi gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Sekikawa, T; Suzuki, E; Ishikawa, K; Takato, H; Yui, N; Shimokawa, R [Electrotechnical Laboratory, Tsukuba (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for analysis and evaluation for development of extra-high efficiency silicon solar cells. It is necessary for development of extra-high efficiency Si solar cells to extend as far as possible service life of minority carriers and to develop the evaluation techniques. Noting photoluminescence (PL) observable even with Si, the method of evaluating characteristics of minority carriers, which are not limited in samples, is developed to experimentally determine their service life from transitional response of the PL characteristics. Si has an extremely low quantum effect, because it is an indirect transitional semiconductor, and needs measurement of very high sensitivity. A rapid heat annealing apparatus and others to generate carriers in the infrared and ultraviolet regions are provided in consideration that these are possible means to increase efficiency. These possibilities will be pursued by developing the annealing techniques. 1 fig.

  2. Analysis and evaluation for practical application of photovoltaic power generation system. Analysis and evaluation for thin substrate polycrystalline solar cells (compound semiconductors and their fabrication technologies); Taiyoko hatsuden system jitsuyoka no tame no kaiseki hyoka. Usumaku taiyo denchi jitsuyoka no tame no kaiseki hyoka (kagobutsu taiyo denchi zairyo oyobi seisaku gijutsu no kaiseki hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    Oyagi, H; Okada, Y; Yamaguchi, H; Shiota, T; Kuroda, S; Igarashi, O; Tanino, H; Makita, Y; Yamada, A; Kimura, S; Ohara, A; Niki, S; Shibata, H; Fons, P [Electrotechnical Laboratory, Tsukuba (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for analysis and evaluation for thin-film compound semiconductor solar cells. The study on epitaxial growth and optical properties of the thin films of CuInSe2 and CuGaSe2 evaluates the thin epitaxial films grown under various conditions, showing morphology of the defects at the interface of heteroepitaxial growth. These results are used to set the growth conditions under which a thin film of high luminescence by exciter recombination is produced. The study also gives information of luminescence transition in the vicinity of the band ends and of energy level between the bands. The study on structural analysis of the epitaxially grown thin films of CuInSe2 investigates dependence of lattice constants of the MBE-grown CIS layer on film thickness by the X-ray diffractometry based on the bond method. The study on epitaxial growth by the Se(CH3)2-halogen transfer method tests epitaxial growth of the single-crystalline Mo on a substrate of single-crystalline sapphire. 5 figs.

  3. Leveling of battery load and extension of battery life by serial connection of electric double layer capacitors with batteries for electric vehicles. Experimental results on the small model; Denki jidoshayo denchi to denki nijuso capacitor no chokuretsu setsuzoku ni yoru denchi futan no heijunka oyobi denchijumyo no enshinka. (kogata model ni yoru jikken seika). Kogata model ni yoru jikken seika

    Energy Technology Data Exchange (ETDEWEB)

    Takehara, J.; Okubo, N.; Miyaoka, K. [Chugoku Electric Power Co. Inc., Hiroshima (Japan)

    1996-10-25

    The load leveling method of batteries for electric vehicles was studied for extension of a battery life and mileage every charging. Under large load fluctuation conditions such as deceleration and acceleration, use of electric power sources other than battery for peek load at acceleration can improve a battery life, output power capacity and mileage every charging. Combination of effective recovery of regenerative power at deceleration with its discharge at acceleration is one of the effective methods. The electric double layer capacitors are serially connected with the batteries, regenerative power is charged only into the capacitors, and both voltages of the battery and capacitor are applied to a power circuit. Battery load is reduced by load on the capacitor. Until the capacitor is re-charged by regenerative power after full discharge, power is supplied only by battery through a diode. Capacitor power is used as effectively as possible until approaching considerably low voltage. As peak load of the battery is reduced by 30%, the mileage increases by 5.7%, and the battery cycle life becomes 1.5 times longer. 7 refs., 5 figs., 3 tabs.

  4. Research on fabrication technology for thin film solar cells for practical use. Technological development for qualitative improvement (CuInSe2 based PV cell); Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Kohinshitsuka gijutsu (CuInSe2 taiyo denchi seizo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on the fabrication technology of CuInSe2 based PV cell in fiscal 1994. (1) On formation of high-quality CIGS thin films by bilayer method, Mo film was deposited on a glass substrate by sputtering, and CIGS film with different Ga/In ratios was next formed on the substrate by quaternary simultaneous deposition at different In and Ga deposition speeds. In addition, CdS film was deposited on the CIGS film, and ZnO and ITO films were finally deposited on it by sputtering to complete solar cell. This solar cell offered the maximum conversion efficiency among cells using CIGS film. (2) On formation of high-quality CIGS thin films by three-stage method, a certain correlation was found between substrate temperature and CIGS film composition by monitoring substrate temperature in film forming process. This phenomenon allowed rigorous control of CIS film compositions important for CIS thin film solar cells. (3) On low-cost process technology for thin film formation, Cu(In,Ga)S2 solid solution film was fabricated by expanded selenic process. 3 figs.

  5. Research on fabrication technology for thin film solar cells for practical use. Research on low-cost fabrication technology for large-area modules (production technology for amorphous silicon solar cell modules); Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Daimenseki module no tei cost seizo gijutsu (amorphous taiyo denchi module seizo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on the fabrication technology of amorphous Si solar cell modules in fiscal 1994. (1) On process technology for prototype film substrate solar cells, an advanced preprocessing equipment for film substrates, stepping roll type film forming technology, and prototype submodules were studied. A conversion efficiency of 7.2% was achieved by use of the submodule formed in an effective region of 40 {times} 40cm{sup 2}. (2) On efficiency improvement technology for film substrate solar cells, p/i and n/i interfaces, forming condition for Ag film electrodes, film thickness of transparent electrode ITO, and optimum transmissivity were studied. (3) On technology for advanced solar cells, high-quality a-SiGe: H film, ion control in plasma CVD, and a-Si film formation by plasma CVD using SiH2Cl2 were studied as production technology of narrow gap materials. (4) On advanced two-layer tandem solar cells, the defect density in optical degradation of a-Si cells by reverse bias dark current was evaluated, and outdoor exposure data were analyzed. 4 figs., 1 tab.

  6. Research on fabrication technology for thin film solar cells for practical use. Research on low-cost fabrication technology for large-area modules (CdS/CdTe solar cell modules); Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Daimenseki module no tei cost seizo gijutsu (CdTe taiyo denchi module seizo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on the fabrication technology of CdS/CdTe solar cell modules in fiscal 1994. (1) On the fabrication technology for high-efficiency large-area solar cells, high-quality CdTe active layer was studied. S content taken in the active layer at sintering of CdTe decreased with an increase in formed CdTe, resulting in improvement of Voc of cells. (2) On the window layer with wide band gap, the solar cell superior in collection efficiency and photoelectric characteristics could be obtained using the newly developed mixed crystal film of Cd(1-x)Zn(x)S. (3) On the forming technology of large-area coating/sintering films, improvement of CdS film quality was studied by pressurized processing of printed CdS films. As a result, improvement of film density and light transmissivity was confirmed. (4) On the leveling process technology of CdTe films, smooth surface films were obtained by experiment using an equipment simultaneously exciting samples in all directions as one of uniform coating methods of films. 7 figs.

  7. Technological development for super-high efficiency solar cells. Technological development for crystalline compound solar cells (research and development of composite materials on solar cells under microgravity environment); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Kessho kagobutsu taiyo denchi no gijutsu kaihatsu (bisho juryoku kankyo wo riyoshita taiyo denchiyo zairyo kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on development of composite materials for solar cells under microgravity environment in fiscal 1994. (1) On a thin film capillary method, 26 experiments of GaSb thin film crystal growth were conducted using the especially prepared high-accuracy electric furnace under microgravity. The wettability of thin film crystals was improved by refining equipment. Rhombus crystal planes and large crystal grains were observed in GaSb thin film crystals prepared under microgravity. (2) On a liquid phase method, the effect of the gravity on crystal structure and grain morphology was studied for synthesis of CdS fine grains. (3) On technological development of composite materials, the solidification experiment of Cu-In-Se melt was conducted under short time microgravity of 10{sup -4}g for 10 sec. As a result, more uniform texture and more high crystallinity were obtained under microgravity, and In in melt was concentrated by surface tension effect. It was suggested that high-quality CIS thin films will be obtained by Se doping into Cu-In composite films under microgravity environment.

  8. Research on fabrication technology for thin film solar cells for practical use. Technological development for qualitative improvement (development of fabrication technology of thin film polycrystalline Si solar cell); Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Kohinshitsuka gijutsu (usumaku takessho silicon kei taiyo denchi seizo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on the fabrication technology of thin film polycrystalline Si solar cells in fiscal 1994. (1) On the fabrication technology of high-quality Si thin films, the new equipment was studied which allows uniform stable melting recrystallization over a large area. The new equipment adopted a heating method based on RTP system, and is now under adjustment. (2) On the fabrication technology of light/carrier confinement structure, degradation of hydrogen-treated thin film Si solar cells by light irradiation was examined. As a result, since any characteristic degradation was not found even by long time light irradiation, the high quality of the cells was confirmed regardless of hydrogen-treatment. Fabrication of stable reproducible fine texture structure became possible by using fabrication technology of light confinement structure by texture treatment of cell surfaces. (3) On low-cost process technology, design by VEST process, estimation of cell characteristics by simulation, and characteristics of prototype cells were reported. 33 figs., 1 tab.

  9. Research on fabrication technology for thin film solar cells for practical use. Technological development for qualitative improvement (improvement of conversion efficiency of amorphous silicon solar cells after degradation); Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Kohinshitsuka gijutsu (amorphous taiyo denchi no shoki rekkago koritsu kojo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on technological development for qualitative improvement of a-Si solar cells after initial degradation in fiscal 1994. On the fabrication technology of light-stable a-Si films, the film formation method possible to control combined hydrogen by repetitive formation/treatment was developed. The obtained high-quality light-stable a-Si film was featured by low defect density in a wide optical band gap range, and defect density of nearly 3 {times} 10{sup 16}/cm{sup -3} after light irradiation. The light degradation rate of the cell where the a-Si film was applied to i layer was relatively stable by 10% or less. The a-Si/a-Si double-layer tandem cell fabricated by this technology produced a high conversion efficiency of 10.5%. By applying {mu}c-Si material to photoactive layer as narrow band gap material, the cell with optical sensitivity even in long wavelength ranges more than 1000nm was obtained. The a-Si/{mu}c-Si double-layer tandem cell produced an initial efficiency of 8.0% and an efficiency after degradation of 7.5%. 12 figs., 3 tabs.

  10. Technological development for super-high efficiency solar cells. Technological development of solar-high efficiency singlecrystalline silicon solar cells (high quality singlecrystalline silicon substrates); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Chokokoritsu tankessho silicon taiyo denchi no gijutsu kaihatsu (kohinshitsu tankessho silicon kiban no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on technological development for high quality efficiency singlecrystalline silicon substrates in fiscal 1994. (1) On electromagnetic casting/once FZ bath method, a Si single crystal of 600mm long was successfully obtained by improvement of power source frequency and furnace parts. High carbon content resulted in no single crystal including solids. In undoped electromagnetic casting ingots, resistivities over 1500ohm-cm were obtained because of effective preventive measures from contaminants. (2) On electromagnetic melting CZ method, since vibration and temperature control of melt surface by magnetic shield was insufficient for stable pulling of single crystals, its practical use was hopeless. (3) On electron beam melting CZ method, a Si single crystal of 25mm in diameter was obtained by preventive measures from evaporation of Si and influence of deposits, and improved uniform deposition distribution in a furnace. The oscillation circuit constant of power source, and water-cooling copper crucible structure were also analyzed for the optimum design of electromagnetic melting furnaces. 3 figs., 1 tab.

  11. Achievement report on Sunshine Program research and development for fiscal 1981. Research and development of amorphous solar cells (Research and development of integrated type amorphous solar cells); 1981 nendo amorphous taiyo denchi no kenkyu kaihatsu seika hokokusho. Shusekigata amorphous taiyo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    An a-SiC (amorphous SiC) material with a wider band gap adds to the conventional hydrogen- and fluorine-based a-Si materials in the study for device efficiency enhancement, and the a-SiC is found suitable as a wide-gap window material. The separated formation technique is found to work effectively for improvement on cell characteristics because it prevents the mixing of impurities of different types. A p-i-n (positive-intrinsic-negative) type amorphous solar cell is subjected to analysis, and a theoretical efficiency of 12.5% is obtained in photoelectric conversion. A conversion efficiency not less than 7% is obtained from an ITO (indium-tin oxide)/p(SiC)-i-n/Al cell on a glass substrate. Design is optimized for area enlargement for an integrated type device, which results in an experimental 10cm-square integrated type solar cell with a conversion efficiency of not less than 5%. As for modularization, a glass substrate for integrated type device is used, as is, as a light-receiving surface protecting board, and studies are conducted thereon. It is then found that the amorphous solar cell experiences some degradation in reliability at the beginning of an irradiation test but that no extensive degradation in reliability is observed even after the passage of 1,000 hours from the beginning of the test. The separated formation technique is found suitable for use in mass production. (NEDO)

  12. Achievement report for fiscal 1981 on Sunshine Program research and development of photovoltaic power systems. Research and development of amorphous solar cells (Research and development of technologies for enlarging amorphous solar cell area); 1981 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Amorphous taiyo denchi no kenkyu kaihatsu (amorphous taiyo denchi no daimensekika gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    In the basic studies of large-area a-Si film formation technologies, the validity is discussed of the evaluation technique using plasma optical emissions spectrometry (OES) employed for the achievement of the intended film qualities. The film forming condition that exerts the greatest influence on the plasma state relative to OES is the power of discharge, and correlations are found to exist between specific emission intensity, infrared absorption level, and photoconductivity of the film. It is found that a P- or B-doped Si:H/SiC:H film is suitable as the material for the window layer on the light-receiving surface of the solar cell. Materials are studied for the i-layer responsible for photo carrier generation, isolation, and acceleration. Studies are also conducted on fluorine-containing film. In the efforts at designing and building solar cells, ITO (indium-tin oxide)/n-i-p/SS (reversed type) cells are analyzed, designing is carried out for transparent electrode film thickness optimization, window effect in stainless substrate cells is improved, glass substrate cells are experimentally built and analyzed, large-area solar cell properties are improved, interaction between the substrate and a-Si is studied, and reliability tests are conducted. For cost reduction, it is necessary to develop technologies of automated production of simplified-structure modules using low-cost materials. Basic matters are taken up for discussion. (NEDO)

  13. Achievement report for fiscal 1981 on Sunshine Program research and development. Research and development of amorphous solar cells (Research and development of amorphous solar cells on flexible film substrates); 1981 nendo amorphous taiyo denchi no kenkyu kaihatsu seika hokokusho. Kadosei film wo kiban to suru amorphous taiyo denchi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-31

    Efforts will be made to reduce the cost, increase efficiency, and enlarge cell areas and, at the same time, to establish the foundation of a roll-up type solar cell manufacturing process which is required for the implementation of mass production. In an inverted pin/ITO (indium-tin oxide) hetero-face structure cell installed on a polymer film substrate, a conversion efficiency of 5.33% is achieved in the case of a solar cell whose n-layer is of the amorphous phase, and 6.36% in the case of a cell of the microcrystallized phase. A roll-up type glow discharge CVD (chemical vapor deposition) unit is designed and experimentally built, which is for the realization of large area cells. It is now duly expected that an undoped (i-type) a-Si:H film will be deposited to a thickness of approximately 5000A. As the result of a first-step screening conducted in search of amorphous solar cell sealing materials, some applicable plastic materials are selected. The future is bright of amorphous solar cells on polymer film substrates. (NEDO)

  14. Fiscal 1993 achievement report on New Sunshine Program. Development of photovoltaic power generation system practicalization technology (Development of ultrahigh-efficiency solar cell technology - Development of crystalline compound solar cell technology); 1993 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu taiyo denchi no gijutsu kaihatsu (kessho kagobutsu taiyo denchi no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Efforts are made to enhance InGaP cell efficiency (target 16%) on a GaAs substrate by prolonging the InGaP minor carrier life span. In preparation of InGaP cell fabrication on silicon, a study is made of epitaxial growth of a wide band gap layer. By improving on the conditions of InGaP heteroepitaxial growth under the MOCVD (metal-organic chemical vapor deposition) method on a GaAs substrate, the InGaP cell base layer minority carrier life span is increased to be longer than 5ns. The use of epitaxial crystals greatly improves on the efficiency of InGaP cells on a GaAs substrate. Furthermore, cell structure improvement and the like are accomplished, which results in the achievement of an efficiency rate of 17.4%. As a basic technology for the fabrication of InGaP/Si tandem cells, experiments are conducted of growing a wide gap layer for the growth of Ln{sub 1-x}Ga{sub x}P on an silicon substrate. For the evaluation of epitaxial crystals and interfaces, time resolution photoluminescence measurement is performed and the result is compared with the result of simulation. (NEDO)

  15. FY 1998 annual report on the fuel/storage working group. 19th R and D activity report; 1998 nendo nenryo chozo gijutsu bunkakai. Dai 19 kai jigyo hokokukai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    Summarized herein are the FY 1998 R and D activities by the fuel/storage working group, extracted from the 19th R and D activity report by NEDO. Mr. Kadoi, a NEDO's director, outlined the R and D activities for development of techniques for fuel cell power generation, development of decentralized cell power storage systems, demonstration of new load-leveling techniques, development of techniques for superlow-loss type power system components, development of techniques for ceramic gas turbines, pioneer R and D for MGC superhigh-efficiency turbine system techniques, demonstration tests for establishing centralized load controlling systems, development of techniques for network systems utilizing wide-area energy, development of techniques for application of superconductor-aided power systems, R and D for power storage aided by a high-temperature, superconducting flywheel, R and D for basic techniques for applying superconductors, and pioneer R and D for basic techniques for AC superconducting power equipment. The individual NEDO's researchers reported their results, which include outline of the fuel/storage technique development group, and current statuses of fuel cell technique development, new cell-aided power storage technique development, and superconductor technique development. (NEDO)

  16. Dynamic programming for reduction of fuel consumption in a photovoltaic/wind/diesel generating system; Doteki keikakuho ni yoru taiyoko/furyoku/diesel hatsuden system no nenryo shohiryo no sakugen

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, K.; Kenmoku, Y.; Sakakibara, T. [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S. [Maizuru National College of Technology, Kyoto (Japan); Kawamoto, T. [Shizuoka University, Shizuoka (Japan)

    1997-11-25

    Dynamic programming is employed in the study of the operation of the diesel engine in a photovoltaic/wind-force/diesel-engine power generating system, which aims at reduction in the system fuel consumption and at determining an optimum system constitution. The parameters set in this system are the photovoltaic/wind-force supply rate, photovoltaic/wind-force power generation ratio, and battery capacity. An island in Ise Bay, with an annual load power of approximately 1.59-million kWh and mean daily load power of approximately 4336kWh is assumed as the location for the system. Observation data of Ommaezaki Weather Station are utilized for the calculation of the amount of photovoltaic/wind-force power generation. It is found as the result that the fuel consumption of the diesel engine in this system decreases to 82-84% when the natural energy supply rate is 20%. It is also found that the fuel consumption of the system records the minimum at a photovoltaic/wind-force ratio of 60/40, irrespective of the battery capacity or natural energy supply rate, and this ratio is the optimum ratio. 3 refs., 9 figs., 1 tab.

  17. Activation of charcoal made from japanese cypress as oxygen electrode in fuel cell by deposition of Pd-metal/Heteropolyacids of the micropores; Kinzokuparajiumu-heteroporisan no bunsan tanzi niyoru hinoki mokutan no nenryo denchisansokyoku to shiteno kinouka

    Energy Technology Data Exchange (ETDEWEB)

    Yumine, Takuya.; Kominami, Hiroshi.; Kera, Yoshiya. [Kinki University, osaka (Japan); Abe, Ikuo. [Osaka Municipal Technology Research Institute, Osaka (Japan)

    1998-12-31

    Pd- and Pt-metal were observed by TEM to be highly disperdsed on charcoal prepared from Japanese Cypress [Hinoki] at 900degreeC (Pd, Pt/H2). Nafion-sheet was hot-pressed with Pd/H2 and Pt/H2 disc-pellets placed in the other sides to make a fuel cell-electrode unit. The 1-V curve in the H{sub 2}-O{sub 2} fuel were measured : The voltage certainly grew with increase in the amount of Pd-metal (1{yields}13wt%) and with a mixing of [Nafion] powder (11wt%). The discharge character was greatly improved with the addition of heteropolyacid (H{sub 3}PMo{sub 11}VO{sub 42};PVMo{sub 11}). When a charcoal prepared from Hinoki at 2400degreeC (HG) was used, the inner resistivity was about 10-times lower than the case of H2 used, although the dispersed states of Pd-metal became considerably poor on HG rather than H2. The actuvuty also increased further with the addition of Nafion and PVMo{sub 11}. (author)

  18. Secretive production of long-chain fatty acids, triacylglycerols and n-alkane-2-ones by fermentation processes; Hakkoho ni yoru ekitai nenryo no seisan wa kanoka (shishitsu no bunpi seisan)

    Energy Technology Data Exchange (ETDEWEB)

    Fukui, S. [University of Fukuyama, Hiroshima (Japan). Faculty of Engineering

    1995-10-20

    Secretive production of lipids, which are useful source for engine-driving fuel, by microbial process using carbohydrate biomasses as substrate has been investigated in our laboratory. This review consists of four parts concerning breedings and selection of lipid-secretive microorganisms : (1) breedings of long-chain fatty acid-secretive strains from Candida lipolytica L-1 by a step-wise mutagenesis process, (2) selection of a triacylglycerol (TG)-secretive and accumulative yeast strain Trichosporon sp. SH45Y, (3) breedings of mutants, SH45Y-derivatieves, having potent ability to produce TG secretively from glucose, a typical biomass charbohydrate, and (4) selection of microorganisms which produce liquid-n-alkane in culture medium by utilizing long-chain fatty acids and TG; a strain of Penicillium decumbens can produce liquid alkalis with a yield of approximately 60 % in weight from palm kernel oil, a commercial TG. 10 refs., 7 figs., 7 tabs.

  19. Attempt of lean burn of a 4 cycle gasoline engine by the aid of low pressure air assisted in-cylinder injection; Tonai kuki nenryo funsha ni yoru lean burn no kokoromi

    Energy Technology Data Exchange (ETDEWEB)

    Hatakeyama, S; Kondo, M; Sekiya, Y; Murayama, T [Hokkaido Automotive Engineering College, Hokkaido (Japan)

    1997-10-01

    Comparable performance and exhaust emission with conventional carburetor was obtained by a low Pressure air assisted in-cylinder injection system. And lean burn of idling and light load operation till A/F=70 was realized by installing a spark Plug and a reed type injection nozzle in a divided combustion chambaer of a 4 cycle gasoline engine. 2 refs., 10 figs.

  20. Fiscal 1996 achievement report. Development of liquid fuel conversion technology (Development for practical application of a new production process); 1996 nendo ekitai nenryo tenkan gijutsu kaihatsu seika hokokusho. Shinseizo process jitsuyoka kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The research and development aims to establish, through verification tests, practical application technologies for two methods, namely, a 'low-temperature liquid phase method' by which cost will be reduced thanks to simplified plant facilities and a 'vapor phase fluidized bed method' in which a composite reforming process may be combined for better economics of scale with a vapor phase fluidized methanol synthesizing method whose facilities may be built to be very large. For the former method, development efforts are made to enable catalyst performance characterization and low-temperature liquid phase methanol production using a small pyrolysis reactor. In the research on pyrolysis reaction, a Raney copper/KOMe/MeOH-based catalyst is used, and this attains a raw material gas conversion efficiency of 92.7%. In the construction of a low temperature liquid phase process, it is found that a single spun conversion efficiency of not less than 90% may be achieved using a heterogeneous catalyst. For the latter method, studies are conducted for the development of, and for the establishment of technologies for designing, synthetic gas production technologies in the development of a heat exchanger type composite reforming furnace and a fluidized bed methanol production process, the development of a catalyst manufacturing technology for fluidized bed practical application, the development of a fluidized bed methanol production technology, and the optimization of the process and its economic efficiency. (NEDO)

  1. Achievement report for 1st phase (fiscal 1974-80) Sunshine Program research and development - Hydrogen energy. Research on hydrogen-fueled engine; 1974-1980 nendo suiso energy seika hokokusho. Suiso nenryo gendoki no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    The research aims to acquire data necessary for designing an engine, which is fueled by hydrogen stored in metal hydrides, for an automobile power plant. It covers the characteristics of hydrogen and their theoretical examination, basic studies on the turbulent mixing and combustion of hydrogen, research using a single-cylinder engine, changes brought into engine performance upon addition of hydrogen, etc. When hydrogen is burned in a spark ignition engine, flashback to the induction system is prone to occur. But this is prevented by directly injecting nothing but hydrogen into the cylinder. In the case of hydrogen fuel, there is the problem of thermal NO generation. Since a hydrogen/air flame is higher in temperature than flames in the case of other fuels, it generates more NO. As techniques for lowering the flame temperature, there are lean fuel combustion, water vapor injection, delayed ignition timing, etc. For the improvement of power and performance, increasing the engine revolution and pressurizing the inlet air are the methods, but both have their own shortcomings. An engine equipped with a third valve is experimentally constructed in this research, which is theoretically free of flashback, suppresses a reduction in the inlet air volume, and necessitates no high-pressure injection system. (NEDO)

  2. Report for fiscal 1998 on results of research and development of silicon-based polymeric material. Material research for the liquid methane fueled aircraft engine; 1998 nendo keisokei kobunshi zairyo no kenkyu kaihatsu seika hokokusho. Methane nenryo kokukiyo engine kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Research was conducted for the purpose of establishing basic technology concerning molecular design, synthesis, material formation, and evaluation of silicon-based polymers which are expected to provide superior electronic/optical functions, high heat/combustion resistance and dynamic properties. The research subjects were such as following: research and development of silicon-based polymeric materials with sea-island microstructures; research and development of silicon-based polymeric materials with sea-island microstructures; research and development on IPN formation with silicon-based polymers; research and development of hybrid silicon polymers with organometallic compounds; research and development of silicon containing polymer materials with ring structures; general committee for investigation and research; the optimized low-temperature Wurtz synthesis and modification of polysilanes; study of unsaturated and hypercoordinate organosilicon compounds; basic studies on the synthesis and properties of silicon-based high polymers; studies of new monomer-synthesis and their polymerization reaction; studies on new method of preparation and functionalization of polysilanes; novel applications of silicon-based polymers in imaging devices for information display, memory, and recordings; and molecular design of silicon-containing {pi}-conjugated and {sigma}-conjugated compounds. (NEDO)

  3. Numerical simulation of growth of flames formed in two-dimensional mixing layer. 2nd Report. Effect of dilution of fuel; Nijigen kongo sonai ni keiseisareta kaen no seicho ni kansuru suchi simulation. 2. Nenryo no kishaku ni yoru eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Noda, S [Toyohashi University of Technology, Aichi (Japan); Hashimoto, K [Sumitomo Metal Industries, Ltd., Osaka (Japan); Nakajima, T [Kobe University, Kobe (Japan). Faculty of Engineering

    1994-07-25

    The effect of fuel dilution on growth of flames formed in 2-D mixing layers was studied by numerical simulation. The methane mass fraction of fuel was adjusted to 1.0, 0.3 and 0.2 through dilution by nitrogen, while the oxygen mass fraction of an oxidizer was fixed at 0.27. Flame structure was complicated due to the flows separated by flame at the leading edge of flames, and three peaks of the second Damkohler number were observed. Fuel dilution by nitrogen caused blow-off of flames, and the mixing ratio of the fuel and oxidizer at the leading edge of flames was essential to blow-off of diffused flames. In the case where vortices were observed in a flow field, the first Damkohler number was important which was determined by the hydrodynamic characteristic time of coherent vortices and the chemical characteristic time of flame propagation based on the mixing ratio of the fuel and oxidizer at the leading edge of flames. The diffused flames were elongated by shearing force, and an exothermic reaction was suppressed and a flame stabilization decreased with a decrease in second Damkohler number. 10 refs., 9 figs., 1 tab.

  4. Stability of diffusion flame formed in a laminar flat plate boundary layer. Effect of fuel dilution; Soryu heiban kyokai sonai ni keiseisareru kakusan kaen no anteisei. Nenryo kishaku no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Takeuchi, M [National Institute for Resources and Environment, Tsukuba (Japan); Ueda, T; Mizumoto, M [Keio University, Tokyo (Japan). Faculty of Science and Technology; Amari, T [Keio University, Tokyo (Japan)

    1998-10-25

    A stability limit of the diffusion flame with fuel injection from a porous wall in a laminar flat plate boundary layer is measured as functions of fuel (CH4) concentration of CH4/N2 injectant mixture ({chi}) and its injection velocity (v). The free stream velocity (U{infinity}) is set as 0.6 m/s. The thermal condition at the wall is controlled by setting temperature at the upstream end of the porous wall as a reference temperature. When v >20 mm/s, the flame becomes unstable with the separation of leading flame edge with decreasing {chi}. The value of {chi} at the stability limit is constant without regard to v as long as the wall temperature is kept constant. As the wall temperature is decreased the value of {chi} increases. The separation is supposed to take place as a result of the limit of the reaction rate. When v <20 mm/s, the flame becomes unstable with the oscillation. The value of {chi} at the stability limit increases drastically with decreasing v. The oscillation takes place mainly due to the repeat of the extinction due to heat loss to the wall and the flame propagation in the combustible layer. 10 refs., 8 figs., 1 tab.

  5. FY 2000 report on research and development of combustion technology utilizing microgravity conditions for fuel diversification; 2000 nendo bisho juryoku kankyo wo riyoshita nenryo tayoka nensho gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This project is aimed at development of optimum combustion technology with diversified fuels, e.g., naphtha and LCO, for gas turbines and others as power sources for topographical energy supply. The combustion under the microgravity is also investigated using the underground facilities at Japan Microgravity Center. Described herein are the FY 2000 results. For construction of combustion model and simulation, the combustion reactions for various liquid fuels are simplified to calculate ignition delay, adiabatic flame temperature and laminar burning velocity with an error less than about 3%. The microgravity combustion experiments are conducted for spray dispersed into a cylinder, to find flame propagation velocities changing with the vaporization characteristics of liquid fuels, and also to construct the combustion models. The premixed turbulent combustion simulation program is developed using a probability density function and analyzed. Development of new combustion technologies includes the study themes of flame propagation and combustion of the air mixture of the multi-component fuel in which the spray exists, combustion characteristics of the droplets of diversified fuels, and combustion of gas turbines with diversified fuels. A propane/air mixture shows different flame propagation characteristics whether it contains kerosene or LCO droplets. The effects of electrical field intensity in the combustion zone on combustion of fuel droplets are elucidated. (NEDO)

  6. Proceedings of the Joint Meeting of The Fuel Society of Japan (1991). 28th Coal Science Conference/91st Coke Meeting; (Sha) nenryo kyokai godo taikai happyo ronbunshu (1991). Dai 28 kai sekitan kagaku kaigi dai 91 kai cokes tokubetsukai

    Energy Technology Data Exchange (ETDEWEB)

    1991-11-07

    Relating to coke, studies are made on the rapid coke production method, oven investigation during carbonization, and operational management/control. As to coal science, studies are mainly on the brown coal two-stage liquefaction (BCL) method, and data on the pilot plant and PSU are reported. Concerning bituminous coal liquefaction, PSU data mostly including the NEDOL process, and characteristics of liquefaction residue and its effective utilization by thermal decomposition are reported. Regarding the liquefaction mechanism, an experimentally extensive study on catalyst, solvent and reaction conditions is made using model materials and coal itself on the bench scale and also in the pilot plant. Engineering subjects on residue, solvent deashing, scale attachment and coprocessing are also reported. Relations of decomposition process to coal chemical structure changes and reaction conditions are investigated. As to coal gasification, studies, which are not many, are conducted on material balance, heat balance, and image characteristics of char for gasification and factors controlling reactivity.

  7. Study of a fuel injection quantity sensor in diesel engine. Part 3. Experimental evaluation of the improved type micro turbine sensor; Diesel kikan ni okeru nenryo funsharyo sensor no kenkyu. 3. Funsharyo keisoku no seido kojo ni kansuru jikken hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Maehara, H; Iwasaki, T; Kobayashi, T [Zexel Corp., Tokyo (Japan)

    1997-10-01

    A Micro Turbine Sensor has been developed to measure fuel injection quantity and injection rate. Previous reports described results of experiments on the MTS which were carried out under steady and unsteady flow conditions. The MTS has been improved in shape of a holder tip and a detecting procedure for rotating speed of a turbine. As a result revolution speed of the turbine increased 18% over the conventional type holder under steady flow condition. Furthermore the measurement resolution of the MTS came up to about 2(mm{sup 3}/pulse) at 20(mm{sup 3}/stroke) under intermittent spray conditions using fuel injection pump. 11 refs., 11 figs., 1 tab.

  8. Three-dimensional analysis of internal flow characteristics in the injection nozzle tip of direct-injection diesel engines; Sanjigen suchi kaiseki ni yoru DI diesel kikan no nenryo funsha nozzle nai ryudo tokusei no kaimei

    Energy Technology Data Exchange (ETDEWEB)

    Ogawa, H; Matsui, Y; Kimura, S [Nissan Motor Co. Ltd. Tokyo (Japan)

    1997-10-01

    To reduce the exhaust emissions and fuel consumption of direct-injection diesel engines, it is essential to optimize the fuel injection equipment closely related to combustion and emission characteristics. In this study, three-dimensional computation has been applied to investigate the effects of the injection nozzle specifications (e.g., sac volume, round shape at the inlet of the nozzle hole) and needle tip deviation on internal flow characteristics. The computational results revealed that the effects of the nozzle specifications and needle tip deviation with a smaller needle lift on internal flow characteristics and a general approach to optimize the injection nozzle specifications were obtained. 3 refs., 10 figs., 1 tab.

  9. Spray characteristics of dimethyl ether (D.M.E.) as on alternative fuel for diesel engine; Daitai diesel nenryo to shite no dimethyl ether (D.M.E.) no funmu tokusei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Wakai, K; Nishida, K; Yoshizaki, T; Hiroyasu, H [Hiroshima University, Hiroshima (Japan)

    1997-10-01

    D.M.E. which was paid attention to as on alternative fuel for a diesel engine, was injected by using Bosch type injection pump and a hole nozzle into a high pressure and high temperature vessel. The spray was observed by using schlieren photography. Spray characteristics, such as, the tip penetration, the cone angle and the volume of the spray were and were compared with a diesel fuel spray. The following thing, and so on were found out as a results. The spray angle of the DME spray of atmosphere pressure Pa=0.1Mpa spreads out large in comparison with the diesel fuel spray, and the way of the change by the pressure is contrary to the case of the diesel fuel spray. 3 refs., 6 figs., 1 tab.

  10. Injection and spray characteristics of a variable orifice nozzle applied the jerk type fuel injection pump for DI diesel engine; Jerk shiki nenryo funsha pump wo mochiita kahen funko nozzle no funsha funmu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Hasegawa, T; Matsui, K; Iwasaki, T; Kobayashi, T [Zexel Corp., Tokyo (Japan); Matsumoto, Y [The University of Tokyo, Tokyo (Japan)

    1997-10-01

    A Variable Orifice Nozzle (VON) by changing a cross-sectional area of the nozzle injection hole, for improving a rate of injection and injection duration, has been developed to study its injection and spray characteristics. The nozzle geometry was optimized to analyze a nozzle internal flow by computational method. Results show that, injection and spray pattern responded to the nozzle orifice cross-sectional area which is changing larger to smaller in the part load range. This results suggest to contribute a combustion improvement which decreasing NOx and soot. 14 refs., 10 figs.

  11. Life cycle assessment for next generating vehicles. Feasibility study of alternative fuel vehicles and electric vehicles; Jisedai jidosha no life cycle assessment. Daitai nenryo jidosha oyobi denki jidosha no feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Hanyu, T; Iida, N [Keio University, Tokyo (Japan)

    1997-10-01

    To show environmental assessment of introduction of substitute fuel vehicles is important information to formulate the future vehicles policy. Life cycle assessment (LCA) is put forward to simulate such potential, allows us to state the reduction environmental impacts of substitute vehicles on their total life cycle. The purpose of this study is assessment and analysis of the life cycle CO2 emission for substitute fuel vehicles, such as, alternative fuel vehicles, electric vehicles, and hybrid electric vehicles. 8 refs., 9 figs., 3 tabs.

  12. Assessment of effects of maturity of Japan`s economy and society and improvement in automotive fuel consumption on demand for automotive fuels; Nippon keizai shakai no seijukuka to nenpi kaizen ga jidoshayo nenryo juyo ni ataeru eikyo hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Shimomura, S. [The Institute of Energy Economics, Tokyo (Japan)

    1998-04-01

    This paper evaluates impacts of the maturity of Japan`s economy and society and the improvement in automotive fuel efficiency on the demand for automotive fuels by FY 2010. Standard case and lower order case were examined. When the traffic volume of passenger cars in FY 1995 is assumed to be 100, it become 121 and 119 in standard and lower order cases, respectively. The traffic volume of lorries become 106 and 102 in standard and lower order cases, respectively, which showed a rather small growth. Deterioration rate of the fuel consumption was estimated by considering the difference in fuel consumption of new cars and existing cars. Although the fuel consumption will be lowered by FY 2000 when the cassation rate of ordinary passenger cars will rapidly increase, the impact will be lowered after that. For lorries for commercial use, the running fuel consumption will be gradually lowered due to the increased carrying capacity and vehicle weight a lorry with improving the transportation efficiency. Decreased running speed by traffic jam is also a cause of the deterioration of fuel consumption. When a policy of improvement in the fuel consumption is promoted in a background of CO2 issues, the fuel consumption of each vehicle will be gradually improved. The peak of fuel demand will be in FY 2005 by considering the changes in economical and social structures and the improvement in fuel consumption for the environmental protection. 5 figs., 3 tabs.

  13. Technologies for simulation improvement of NOx and PM emissions and fuel consumption of future diesel engines for heavy-duty trucks; Shorai no ogatasha diesel engine ni okeru NOx, PM, nenryo shohi no kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Shimoda, M.; Shimokawa, K.; Uchida, N.; Tsuji, Y.; Yokotaa, H.; Hosoya, M. [Hino Motors, Ltd., Tokyo (Japan)

    1999-01-01

    Future diesel engines for heavy-duty trucks are required to have significantly low NO{sub x} and PM emissions and fuel consumption characteristics. In order to improve these characteristics, various technologies including high pressure fuel injection systems, combustion optimization. high boost pressure turbocharging, EGR homogeneous charge compression ignition combined with multiple injections, and aftertreatment are discussed. As each technology has a number of challenges to overcome, it will take long before engines with these technologies are commercially available. In this paper, the research activities accomplished to date are reported. (author)

  14. New concept for low emission diesel combustion. 2nd Report. Combustion improvement by applying EGR and oxygenated fuel; Teikogai diesel engine no nensho concept. EGR, gansanso nenryo ni yoru nensho kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Yokota, H.; Nakajima, H.; Kakegawa, T. [Hino Motors, Ltd., Tokyo (Japan)

    1998-05-01

    Described herein are performance of a new concept of premixed, multiple injection combustion, in which part of the fuel is injected into the combustion chamber at the early stage and the remainder is injected in the ordinary manner, and characteristics of the exhaust gases. Also described are the effects of EGR and oxygenated fuel on reduced HC emissions and fuel consumption. The ordinary premixed, multiple injection combustion system has problems related to fuel efficiency, and HC and particulate missions. When combined with an EGR system, this system reduces HC emissions to one-third. MTBE shows an effect of improving fuel efficiency, when mixed with diesel fuel. No particulate matter is exhausted and fuel efficiency is improved by 6%, when MTBE is present in the fuel at 30% by weight. The pre-mixture is less homogeneous in the absence of EGR and oxygenated fuel, producing a luminous flame observed in the fuel-rich region. No such a flame is observed, when MTBE is added to the fuel and suction air temperature is increased to the level corresponding to that associated with EGR, conceivably resulting from increased suction air temperature and lower boiling point of MTBE, which together make the pre-mixture leaner and more homogeneous. 7 refs., 9 figs., 2 tabs.

  15. Study on initial stage of diesel spray formation. Effects of the condition inside the nozzle sac; Diesel funmu no shoki keisei katei ni kansuru kenkyu. Sac nai nenryo no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, N.; Tsujimura, K. [Nissan Diesel Motor Co. Ltd., Saitama (Japan); Komori, M.

    1996-06-25

    To realize clean diesel exhaust, it is very important to clarify the atomization phenomena of the fuel spray. In this study, the initial stage of the atomization process of a diesel injection fuel spray was analyzed with a high-speed image converter camera under the conditions of atmospheric gas pressure and room temperature. As a result, it was found that the initial spray formation was greatly affected lay the condition inside the nozzle sac. In the case in which fuel existed in the sac, pin-like structure spray formation was observed at the initial injection stage. This phenomenon was not observed in the case in which no fuel was present in the sac, and a widely spread fuel spray formation was observed at the initial injection stage. The relatively low-speed fuel spray injected in the initial low-sac-pressure condition was pushed away by the subsequent fuel spray injected in the high-sac-pressure condition. 7 refs., 12 figs., 1 tab.

  16. Fiscal 1993 achievement report on next-generation industrial structure technology (Advanced materials for extreme environments - Development of methane fueled aeroengine); 1993 nendo chotaikankyosei senshin zairyo no kenkyu kaihatsu seika hokokusho. Methane nenryo kokukiyo engine no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Efforts were exerted to develop advanced materials for use under extreme environments, which were intermetallic compounds and fiber reinforced intermetallic compound composite materials excellent in heat resistance, specific strength, oxidation resistance, or the like. For the development of intermetallic compounds, efforts were made to develop Ti-Al-X (X=metal) high specific strength intermetallic compounds and Nb-Al-X (X=metal) high melting point intermetallic compounds. Ternary phase diagrams were prepared and the effect of added elements on basic characteristics was investigated. Basics of element technologies (texture control, melting, casting, and isothermal rolling) for manufacturing panel materials were studied and, in the case of Ti-Al-X systems, Ti-Al thin panels were fabricated. In the case of Nb-Al-X systems, items were experimentally fabricated by casting in an effort to study precision casting technology optimization. For the development of composite materials, efforts were made to develop SiC based and SiMC (M=metal) based fibers, and studies were carried out to complex them with Ti-Al based matrices. (NEDO)

  17. Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of technologies to manufacture applied type thin film solar cells with new structure and development of high-efficiency hybrid thin film/sheet solar cells); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (oyogata shin kozo usumaku taiyo denchi no seizo gijutsu kaihatsu (kokoritsu hybrid gata usumaku / sheet taiyo denchi no seizo gijutsu kaihatsu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to develop low-cost and high-efficiency hybrid thin film/sheet solar cells, research and development has been performed. This paper summarizes the achievements in fiscal 1999. The research is related to a hybrid construction, in which the upper cells of amorphous silicon thin film are formed on the lower cells bonded with micro-crystalline silicon thin film relative to a poly-crystalline silicon sheet. In the technology to form the upper cells, a pin-construction using amorphous silicon thin film made by using the plasma CVD process was adopted, whereas an open circuit voltage of 1.45V, a short circuit current of 13.6 mA/cm{sup 2}, and a conversion efficiency of 13.5% were obtained. In the technology to form the substrate for the lower cells, formation of flat silicon thin plate that can be peeled off was identified as a result of adopting the construction in which a graphite substrate is provided on a rotating cooling body of 12-prism type. With regard to the technology to bond and form the lower cells, electrical properties of hetero-bonded cells were discussed, and an open circuit voltage of 0.605V and a conversion efficiency of 14.3% were obtained as a result of enhancing the film quality and optimizing the film thickness. (NEDO)

  18. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of next-generation thin-film solar cell module manufacturing technology - Development of CIS solar cell module manufacturing technology - Development of high-quality film enlargement technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / jisedai usumaku taiyo denchi module no seizo gijutsu kaihatsu / CIS taiyo denchi module no seizo gijutsu kaihatsu / kohinshitsumaku no daimensekika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The project aims to establish a manufacturing process that enables both high-quality CuInSe{sub 2} (CIS) film solar cell enlargement and cost reduction and to develop a device structure which uses less heavy metal for the purposes of increasing the CIS thin-film solar cell size and efficiency and decreasing environmental impact. Several element technologies have been established for increasing the area of high-efficiency Cu(In, Ga)Se{sub 2} (CIGS) solar cells. Concerning the enlargement of the photoabsorption layer which is to assume the most important role, it is found that a high-quality CIGS film, which is near homogeneous though within a 10cm times 10cm area, is fabricated by an in-line vapor deposition method. As for dead area reduction and high-speed patterning, it is found that laser scribing works effectively in the patterning of the window layer and photoabsorption layer. As for reduction in the use of heavy metal, a high efficiency of 16.2% is attained in a cell not using a CdS film as expected in the case of a cell using a CdS film, this thanks to a CIGS film surface reforming technique. The technique of junction formation for CIGS solar cells is improved, and then a true efficiency of 18.5% is achieved. (NEDO)

  19. Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system/development of technology to manufacture thin film solar cells/development of technology to manufacture low-cost large-area modules/development of technology to manufacture next generation thin film solar cells (development of technology to manufacture applied type thin film solar cells with new construction); 1997 nendo tiayoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module esizo gijutsu kaihatsu (jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu, oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A thin film single crystal silicon solar cell module is developed, in which a porous silicon layer is formed on the surface of a long-sized single crystal silicon substrate, a single crystal silicon film is integrated on the layer by epitaxially growing the film thereon to form a solar cell, and the solar cell is peeled off from the silicon substrate and transferred to a plastic film substrate. The achievements during this fiscal year may be summarized as follows: simultaneous formation of a porous silicon layer on a silicon substrate, reduction of anode formation current density from 200 mA/cm{sup 2} to 10 mA/cm{sup 2}, development of a silicon epitaxial device using a carbon heater, and attainment of aperture conversion efficiency of 11.8% in a thin film single crystal silicon solar cell. Three kinds of methods were developed to peel off the solar cell. A method was developed to grind silicon substrate surface from which the solar cell has been peeled off. A technology was developed to obtain a long-sized silicon substrate of about 30 cm times 10 cm times 0.1 cm from a 4-inch silicon ingot by using a wire saw. (NEDO)

  20. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost large-area module manufacturing technology - Development of next-generation thin-film solar cell manufacturing technology - Development of CIS solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu / jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu / CIS taiyo denchi module no seizo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This research aims to achieve a conversion efficiency of 13% and a manufacturing cost of 140 yen/Wp with a 30cm times 30cm Cu(InGa)Se{sub 2}-based thin-film solar cell submodule. Ga and sulfur are combined and a film fabrication technology was developed which would improve on Voc. Concerning Ga, a laminated precursor layer was fabricated and evaluated, which comprised a Cu-25wt%Ga alloy layer and a Ga source which was a Cu-48%Ga alloy layer. Concerning sulfur, the vapor phase selenization temperature and the selenization retention time in an H{sub 2}Se gas atmosphere was allowed to vary for a change in Cu(InGa)Se{sub 2} calcopyrite crystallinity for the study of relations between the amount of sulfur taken in and the solar cell characteristics, and the relations were assessed by EPMA (electron probe microanalyzer). Technologies were developed for the fabrication of high-resistivity buffer layers by solution growth, for the fabrication of window layers (transparent, conductive ZnO film) by sputtering, and for their patterning. Submodules of a ZnO/Zn(O,S,OH)x/Mo structure were fabricated, 10cm times 30cm and 30cm times 30cm in size. The former achieved 12.5% in conversion efficiency, and the latter 11.6%. (NEDO)

  1. Achievement report for fiscal 1997 on development of technologies for practical photovoltaic system under New Sunshine Program. Manufacture of thin-film solar cell / low-cost and large-area module / next-generation thin-film solar cell (Manufacture of thin-film polycrystalline solar module); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu, jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (usumaku takessho taiyo denchi module no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Fiscal 1997 is the first year of another 4-year-long research and development phase. In addition to researches for improving on thin-film polycrystalline Si cell efficiency that have been under way, new efforts are started, which include the development of practicality-conscious thin film producing technologies aiming at higher throughput and yield and the development of modularization process technologies which are necessary for putting thin-film cells to practical use. Concerning the formation of a power generation layer on a polycrystalline Si thin film formed by the ZMR (zone-melting recrystallization) process, studies are conducted for improvement on its throughput and yield using a new CVD (chemical vapor deposition) unit. A method of modularization is evaluated, which involves a laminate of a thin-film cell attached to a resin-coated, reinforced glass substrate and an EVA (ethylene vinyl acetate) back film. A remarkable achievement is earned toward the practicalization of technologies of thin film formation enhanced in quality and throughput and technologies of thin film modularization. (NEDO)

  2. Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost large-area module manufacturing technologies, and development of technologies to manufacture amorphous silicon/thin film poly-crystalline silicon hybrid thin film solar cells); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo kaihatsu (oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu (amorphous silicon / usumaku takessho silicon hybrid usumaku taiyo denchi no seizo gijutsu kaihatsu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Developmental research has been performed on large-area low-cost manufacturing technologies on hybrid thin film solar cells of amorphous silicon and poly-crystalline silicon. This paper summarizes the achievements in fiscal 1999. The research has been performed on a texture construction formed naturally on silicon surface, and thin film poly-crystalline silicon cells with STAR structure having a rear side reflection layer to increase light absorption. The research achievements during the current fiscal year may be summarized as follows: the laser scribing technology for thin film poly-crystalline silicon was established, which is important for modularization, making fabrication of low-cost and large-area modules possible; a stabilization efficiency of 11.3% was achieved in a hybrid mini module comprising of ten-stage series integrated amorphous silicon and thin film poly-crystalline silicon; structures different hybrid modules were discussed, whereas an initial efficiency of 10.3% (38.78W) was achieved in a sub-module having a substrate size of 910 mm times 455 mm; and feasibility of forming large-area hybrid modules was demonstrated. (NEDO)

  3. Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture application type thin film solar cells with new structure (development of technologies to manufacture amorphous silicon and thin film poly-crystal silicon hybrid thin film solar cells); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu (amorphous silicon/usumaku takessho silicon hybrid usumaku taiyo denchi no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research and development was performed with an objective to manufacture amorphous silicon and thin film poly-crystal silicon hybrid solar cells with large area and at low cost, being a high-efficiency next generation solar cell. The research was performed based on a principle that low-cost substrates shall be used, that a manufacturing process capable of forming amorphous silicon films with large area shall be based on, and that silicon film with as thin as possible thickness shall be used. Fiscal 1997 has started research and development on making the cells hybrid with amorphous silicon cells. As a result of the research and development, such achievements have been attained as using texture structure on the rear layer in thin poly-crystal silicon film solar cells with a thickness of two microns, and having achieved conversion efficiency of 10.1% by optimizing the junction interface forming conditions. A photo-deterioration test was carried out on hybrid cells which combine the thin poly-crystal silicon film cells having STAR structure with the amorphous silicon cells. Stabilization efficiency of 11.5% was attained after light has been irradiated for 500 hours or longer. (NEDO)

  4. Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost large-area module manufacturing technologies, next generation thin film solar cell module manufacturing technologies, development of thin film poly-crystalline solar cell module manufacturing technologies); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (usumaku takessho taiyo denchi module no seizo gijutsu kaihatsu)))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development has been performed on a high throughput forming technology and a modularization technology for thin film poly-crystalline solar cell modules. This paper summarizes the achievements in fiscal 1999. In developing the high throughput forming technology for a high-quality thin film, research has been made on a low-cost VEST process to re-utilize substrates by separating the thin film from the substrate. In the melting re-crystallization process, it was discovered that plasticity deformation of the substrate can be reduced greatly by raising the substrate heating temperatures. It was also found out that substrate warping amount can be reduced to about one-fifth of the conventional amount by making the thickness greater than 1.5 mm and raising the heating temperatures higher than 1300 degree C. In developing the thin film modularization technology, it was indicated that the property improving effect remains the same even if the hydrogen passivation method is changed from the hydrogen ion injection to the hydrogen plasma processing. In the trial fabrication of the thin film modules, a conversion efficiency of 13.1% was achieved in nine-cell structured modules. (NEDO)

  5. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost large-area module manufacturing technology - Development of next-generation thin-film solar cell manufacturing technology - Development of thin-film polycrystalline solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu / jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (usumaku takessho taiyo denchi module no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The aim is to realize the practical application of the above-named solar module expected to exhibit higher efficiency and reliability and achieve cost reduction through consumption of less materials. In fiscal 1998, 1) technologies were developed to reduce substrate warpage during recrystallization for the higher-throughput fabrication of high-quality thin films and 2) technologies were also developed for the realization of higher-throughput fabrication of thin films and for efficiency improvement for thin-film modules. Under item 1), experiments were conducted by simulation for reducing warpage to occur in thin-film polycrystalline Si substrates during fabrication by melting and recrystallization. Under item 2), for the development of thin-film cell high-throughput technologies, studies were started on a more practical hydrogen plasma process to challenge the conventional process of crystal defect inactivation by hydrogen ion injection with which achievement of high throughputs is difficult. For the development of technologies for the enhancement of thin-film module efficiency, efforts were exerted to realize a 10cm times 10cm square shape for the enhancement of efficiency in the process of filling modules with cells. These efforts achieved a great step toward future practical application. (NEDO)

  6. Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost large-area module manufacturing technologies, next generation thin film solar cell module manufacturing technologies, development of CIS solar cell module manufacturing technologies); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (jisedai usumaku taiyo denchi no seizo gijutsu kaihtsu (CIS taiyo denchi module no seizo gijutsu kaihatsu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development has been performed on a technology to manufacture CIS-based thin film solar cells. This paper summarizes the achievements in fiscal 1999. In the research of a large-area light absorbing layer manufacturing technology, investigation was made on light absorbing layers in manufacturing sub-modules with a size of 30 cm times 30 cm. With regard to the temperature condition in the light absorbing layer forming process, it was found that the cooling rate affects particularly the adhesion in the connecting interface of the light absorbing layer and the Mo rear electrode layer. In addition, it was revealed that the sulfur take-in amount can be increases by extending the retention time at the sulfurizing temperature and by decreasing the temperature to turn the gas phase into selenium. In the research of elementary technologies to establish the mass production process, developments were performed on the high-resistance buffer layer manufacturing technology, the high-quality window layer film manufacturing technology, and the technology to manufacture rear electrode layer made of high-quality metals. In developing the patterning technology, two kinds of the existing patterning devices were modified and adjusted for patterning the substrates with a size of 30 cm times 30 cm. In addition, a processing device was installed in the conventional manually operated process for module finishing. (NEDO)

  7. Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture thin film solar cells, development of technologies to manufacture low-cost large-area modules, development of technologies to manufacture next-generation thin film solar cells (development of technologies to manufacture CIS solar cell modules); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu, jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (CIS taiyo denchi module no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research and development was made with an objective to achieve conversion efficiency of 13% in a 30 cm times 30 cm size submodule of a CIS-based thin film solar cell, and to develop a manufacturing technology that can achieve 140 yen/Wp. This paper describes the achievements attained during fiscal 1997. In fiscal 1997, based on the achievements reached during the previous year, a submodule with a size of 10 cm times 30 cm was fabricated for an attempt of improving the open voltage and short circuit current density. Simultaneously, the applicability thereof to a module with an area as large as 30 cm times 30 cm was evaluated. As a result of experimental discussions, enhancement in the open voltage was verified by increasing amount of Ga or sulfur, but it was not possible to achieve 600 mV or higher. In the research of component technologies to establish a mass production process, research and development was made on a high-resistance buffer layer film forming technology, a high-quality window layer film forming technology, a high-quality metallic rear electrode film forming technology, and patterning technologies. The outdoor exposure test was continued on laminated mini-modules with a size of 10 cm times 10 cm. (NEDO)

  8. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost large-area module manufacturing technology - Development of application type novel-structure thin-film solar cell manufacturing technology - Development of amorphous silicon/thin-film polycrystalline silicon hybrid thin-film solar cell manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu / amorphous silicon/usumaku takessho silicon hybrid usumaku taiyo denchi no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The project aims to manufacture the above for the development of low-cost high-efficiency practical cells. Technologies were developed to homogeneously fabricate films with an average efficiency of 10% or more in a 100mm times 85mm area in a STAR (naturally surface texture and enhanced absorption with a back reflector) structure thin-film polycrystalline silicon (poly-Si) solar cell. The texture shape was improved for a higher light trapping effect and a STAR structure cell highly sensitive to long wavelengths and fit for use for a hybrid cell bottom layer was obtained. Various cells were examined for temperature characteristics, and it was found that thin-film poly-Si cells present a temperature coefficient equal to or less than that of bulk single-crystal silicon systems, and hybrid cells a temperature coefficient similar to that of a-Si systems. The technology was applied to a hybrid solar cell in which an a-Si cell was placed on STAR structure thin film poly-Si cells, and a resultant 3-layer a-Si/poly-Si/poly-Si cell exhibited a stabilization factor of 12.0% after 550 hours of optical irradiation. (NEDO)

  9. Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system/development of technology to manufacture thin film solar cells (development of technology to manufacture applied type thin film solar cells with new construction) (development of technology to manufacture micro light collection type solar cells); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu (micro shukogata taiyo denchi no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    These technological developments are intended to demonstrate module efficiency of a micro light collection type solar cell of 15% by fiscal 2000, and obtain prospect on the module manufacturing cost of 140 yen per watt. Discussions given during fiscal 1997 are as follows: development has been performed on a design method to decide construction of a non-tracking micro light collection type module; in the state of cells being integrated on the module, the cells are arranged minutely and discretely, whereas, with discussions on a method to form them and assessment of the optical system as the main objective, single crystal silicon solar cells with a size smaller than 5 mm were fabricated on a trial basis; problems of forming micro cells by using the wafer cutting process were clarified; micro cells operating on light collection were fabricated trially to extract technological problems in light collecting operation and discuss technical problems in mass production; and development was performed on an evaluation method to analyze the cells' light collecting operation, and discussions were given on a method to estimate power generation amount from the light collection type modules. (NEDO)

  10. Fiscal 1999 geothermal energy development promotion survey. Report on environmental impact survey - 5 (Musadake area); 1999 nendo chinetsu kaihatsu sokushin chosa. Kankyo eikyo chosa hokokusho (No.B-5 Musadake chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-01-01

    For the purpose of clarifying the environmental impact to result from the digging of borehole N11-MD-3 in Shibetsu-gun, Hokkaido, a survey was conducted of changes in (1) hot spring water quality, (2) noise/vibration pollution, and (3) air pollution due to hydrogen sulfide, before and after the digging period. Under item (1), measurements were made at four hot springs, which involved weather, air temperature, water temperature, amount of welled-up water, pH, electric conductivity, etc. Although minor changes were observed during the measuring period, none was found related to the digging process. Under item (2), noise levels were measured during the drilling period along the site boundary, at a point 500m from N11-MD-3, the Kawakita hot spring, and the entrance of Sekiyunosawa. Along the site boundary, they were 55-60 dB during the drilling period, and there was an increase of 30dB attributable to the drilling. At the 500m point, there was a 15-20dB increase attributable to the same. Vibration levels during the drilling period were 40dB along the site boundary and less than the observable minimum at the other points. Under item (3), at four points along the site boundary (50m), hydrogen sulfide concentration in the air fluctuated by 0.01-0.21ppm when the steam discharge rate was 4.47-7.20t/h. (NEDO)

  11. Confirmation study of the effectiveness of prospect techniques for deep geothermal resources. Deep-seated geothermal resources survey report (Fiscal year 1993); 1993 nendo chinetsu tansa gijutsu nado kensho chosa. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Drilling and survey of deep geothermal exploration wells were conducted in order to grasp the existing situation of deep geothermal resource and the whole image of geothermal systems in the area where geothermal resource was already developed. Following fiscal 1992, the well was drilled in fiscal 1993 down to depths of 605m-1505m, and a 13-3/8 inch casing was inserted down to a depth of 1500m. In the drilling, four cores including oriented cores were sampled, and microscopic observation, X-ray diffraction analysis, fluid inclusion survey, core property test, etc. were conducted. In the FMI logging, detected were 273 bedding planes, 483 fractures, etc. Further made were a velocity structure survey, a gravity survey in the area of 270 km{sup 2} including deep exploration wells, a quality survey of the Kakkonda river water, etc. As to geothermal structure models in the Kakkonda area, results of the drilling were added to prediction models before drilling deep exploration wells, but the revision was not very much. Besides, studies were made of a survey method using microearthquakes, a survey technique using resistivity, etc. 61 refs., 259 figs., 95 tabs.

  12. Fiscal 1995 report on the survey of making models for introducing petroleum substituting energy systems. 2; 1995 nendo chosa hokokusho (sekiyu daitai energy system donyu model sakusei ni kansuru chosa). 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    In the promotion of measures taken for energy conservation, it is necessary to give local governments, entrepreneurs, etc. guidance for introducing energy systems which meet with features of the buildings and courses for how to construct infrastructures of towns or cities in case of development, redevelopment, etc. In fiscal 1995, each of the petroleum substituting energy systems was studied more detailedly, and the trend of building facilities for the introduction was studied and arranged. Energy systems by the following were set up paying attention to energy sources, energy conversion and energy transportation as factors composing a petroleum substituting energy system: photovoltaic power generation, use of solar energy, use of wind energy, use of geothermal energy, use of biomass energy, use of waste, use of temperature difference energy, cogeneration, load levelling, wide-area energy supply, etc. Also studied and arranged were energy demand, location, the recent trend, the point of introduction of energy systems, examples of introduction, etc. in relation to indoor sport facilities, hospitals, hotels, multiple dwelling apartments, commercial facilities, offices, plants, etc. 52 figs., 55 tabs.

  13. Leading research report for fiscal 1998. Research and study of 3-dimensional cell structure module engineering; 1998 nendo sendo chosa kenkyu hokokusho. Sanjigen saibo soshiki module kogaku chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the formation of cellular tissues to replace bionic tissues, researches were conducted about technologies of forming bionic tissue modules by culturing various kinds of cells. As for the materials and methods for constructing cellular tissues, researches were conducted about the trends of research and development of 3-dimensional tissue culturing matrices and materials for micromanipulation. As for the development of technologies for the functionalization of 3-dimensionally structured cells, research and study were conducted about the technology of 3-dimensional cell structure organization through application of physical stimulation, the biochemical technology of differentiation inducing, and the differentiation inducing technology for hetero tissue culturing. As for the development of technologies for evaluation using 3-dimensionally structured cells, light CT (computer tomography), analysis and evaluation using spectroscopy and the like, feasibility of the biochemical analysis of the cell state using biosensors, technologies for measuring the secretion of carcinogenic and toxic substances, etc., were studied. In addition, the development of organic models to replace test animals, industrial evolution of 3-dimensional tissue module engineering, etc., were investigated. (NEDO)

  14. FY 1998 report on the verification survey of geothermal exploration technology, etc. 1/2. Survey of deep geothermal resource; 1998 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 1/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-12-01

    For the purpose of commercializing deep geothermal resource, a deep exploration well of 4000m class was drilled in the existing geothermal development area to survey the situation of deep geothermal resource existence and the availability. Concretely, the deep geothermal exploration well was drilled for study in the Kakkonda area, Shizukuishi town, Iwate prefecture, to clarify the situation of deep geothermal resource existence and the whole image of geothermal system. Consideration was made of the deep geothermal exploration method, systematization of deep high temperature drilling technology, and availability of deep geothermal resource. The results of the survey were summed up as follows: 1) general remarks; 2) deep exploration well drilling work; 3) details of the study. 1) and 2) were included in this report, and 3) in the next report. In 1), the items were as follows: the study plan/gist of study execution, the details and results of the deep geothermal resource survey, the outline of the deep exploration well drilling work, and the outline of the results of the FY 1998 study. In 2), the drilling work plan/the actual results of the drilling work were summed up. As to the results of the study, summarized were the acquisition of survey data on deep exploration well, heightening of accuracy of the deep geothermal resource exploration method, etc. (NEDO)

  15. Fiscal 2000 report on financially supported geological structure survey overseas. Basic survey for coal resource exploitation (Research on underground probing technology); 2000 nendo kaigai chishitsu kozo chosahi nado hojokin (sekitan shigen kaihatsu kiso chosa) konai tansa gijutsu chosa hokokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the work of searching for coal beds, comparison is made between the geological structure of the object area, which is predicted, before actual investigation, by a close scrutiny of the result of oceanic pilot boring conducted in the past, result of geophysical exploration, and the geological features of galleries already in presence in the vicinity, and the result obtained from galleries drilled actually for the investigation. The investigation was conducted at the Ikeshima coal mine, Nagasaki Prefecture. In this fiscal year, 5 investigation galleries were drilled, totalling 1640m in length, and, in the mine, geological surveys, survey and measurement, coal quality evaluation, water emergence investigation, boring for coal, etc., were carried out. Comparison was made, and, though in the 2nd Minami No. 06 air duct there was no important difference detected between the prediction and the actual result, some faults were found to exist which had not been predicted by seismic exploration on the ocean. In the 2nd Minami No. 5 air duct, the actual geology was not different from the predicted geology, this endorsing the usefulness of boring for coal. In the 2nd Minami No. 01 gallery, direction and inclination were not greatly different from what had been predicted, but some faults which had not been predicted were discovered. These faults had escaped the scrutiny of neighboring coal beds and pilot boring. (NEDO)

  16. Leading research and study report for fiscal 1998. Report on leading research and study on intelligent fiber; 1998 nendo sendo chosa kenkyu hokokusho. Inteligent fiber sendo chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Researches were conducted with a view to organizing projects for developing intelligent fibers, equipped with environmental friendliness and amenity without being deprived of their original properties as structural and clothing materials, the ultimate goal of the effort being the creation of harbingers of next-generation fibers which would contribute to the advance of industries related to environments, medicine and welfare, and information. What were learned from fiscal 1998 researches are mentioned below. The strength that the general-purpose fibers currently in use exhibit is so small as to be but several percent of what is theoretically predicted for them. Demand will increase a great deal if the actual strength is doubled, for which new technologies have to be developed including those involving super-fiber texture control. For providing the fiber with such functions as environment-friendliness, amenity, etc., it is necessary to develop phasal structure control technologies with regard to fiber morphology, surface texture, etc. For success in practical application in the future of such super-fiber materials, each specimen needs to be manufactured in the order of kilogram by way of trial. Moreover, fiber evaluation techniques have to be developed in the three domains of software, hardware, and interface. (NEDO)

  17. Basic investigation on promotion of joint implementation in fiscal 2000. Survey on energy saving and CO2 emission reduction in Cilacap Refinery; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Cilacap seiyusho ni okeru shoene CO2 sakugen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective of saving energy and reducing greenhouse gas emission, a basic survey has been performed on the atmospheric crude oil distillation units and the high vacuum distillation units at Cilacap Refinery in Indonesia. The first site survey in September 2000 has carried out a survey on the situation of the facilities and operation upon obtaining the facility data and operation information from Pertamina. As a result, it was revealed that there is a room of improvement in the heat recovery, whereas a modification design was executed on the improvement proposals on the heat exchanger system. However, the second site survey in November 2000 has revealed that Pertamina had executed in 1998 through 1999 the de-bottlenecking project on the crude oil atmospheric distillation units (two units) and the high vacuum distillation units (two units), by which the capability has been expanded, and the heat recovery rate has been increased. It is not possible to look for extremely large enhancement of the heat recovery rate beyond that point, and the reduction of CO2 emission would also be small. As a result of discussions, the present project was found capable of reducing annually the CO2 emission by 36,500 tons. (NEDO)

  18. Report on fiscal 2000 geothermal development promotion survey. No. C-5 Appi district environmental impact survey (1st phase); 2000 nendo chinetsu kaihatsu sokushin chosa hokokusho - No.C-5. 1. Appi chiiki kankyo eikyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-08-01

    For the survey of weather in the Appi district, Iwate Prefecture, observation data covering the last decade were collected at weather stations and the like, and characteristics of weather, climate, and natural earthquakes were learned. In the survey of fluctuation in the spa water level, studies were made about fluctuation in water temperature, spring water, and river water, and basic data were collected for the examination of the impact to be generated by geothermal exploration well boring and short-term discharge tests. In the survey of animal and vegetables, the habitation and distribution of animals and vegetables at sites planned for geothermal well boring were investigated, and data were collected for the evaluation of the impact to be imposed on them by well boring or the like. In the survey dealing with nature conservation and landscape, laws and regulations governing nature conservation were collected and put in an easy-to-use order, and seasonal changes in the natural landscape were photographed and recorded. In the survey of noise/vibration and ground fluctuation, the background values were measured prior to the implementation of geothermal well boring, discharge tests, and so forth. (NEDO)

  19. Report on fiscal 1999 survey for geothermal exploration technology verification. Survey of deep-seated geothermal resources; 1999 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    To promote the development of deep-seated geothermal resources in a rationalized way, studies were conducted about deep-seated geothermal resource assessment techniques, development guidelines, and the like. For the development of techniques for estimating deep-seated geothermal reservoir parameters, the Uenotai district, Akita Prefecture, and the Hatchobaru district, Oita Prefecture, were designated as model fields, and a geothermal system conceptual model was fabricated. Data of the two districts were registered in a database. Using these data, verification was performed of the validity of stochastic estimation techniques, large area flow simulation, rock/water equilibrium reaction simulation, and the like. As for the technique of deep-seated resource amount estimation, a simplified reservoir model was experimentally constructed based on parameters determined by the stochastic estimation of deep-seated reservoirs and on the conceptual model, and a method was studied for TOUGH2-based production prediction. Studies were also made about deep-seated geothermal resource development guidelines, such as exploration guidelines, exploration well boring guidelines, and geothermal fluid production guidelines. (NEDO)

  20. Fiscal 1994 entrusted task report. Surveys of advanced natural gas development and efficient utilization (Survey of coal hydrogasification technology development); 1994 nendo tennen gas kodo kaihatsu yuko riyo chosa tou itaku gyomu hokokusho. Sekitan suiten gaska gijutsu kaihatsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    For the establishment of a practical process for substitute natural gas (SNG) production, technological and economical assessments were made, and tasks to discharge for the development were discussed. In this fiscal year, the results of surveys conducted in the past five-year period were compiled, and studies were made to prepare for a smooth transition to the element research stage. Findings obtained are described below. SNG producing technologies need to be developed, with the demand for SNG increasing sharply, to further stabilize the base for SNG supply; coal which is abundantly available should be used as the material for SNG; and coal hydrogasification, among various methods for producing SNG from coal, is the most suitable in view of efficiency and cost performance. It was also found after a prolonged study for the improvement of efficiency and cost performance that probabilities were high that the yield of BTX (benzene, toluene, xylene) would increase and cost performance would improve. Besides, a basic plan and an element technology research plan were prepared for the development of the ARCH (advanced rapid coal hydrogasification) process. (NEDO)

  1. Survey report of FY 1997 on the trends of novel CO2 fixation technology using bacteria and microalgae; 1997 nendo chosa hokokusho (saikin sorui wo riyoshita atarashii nisanka tanso kotei gijutsu no doko chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For this survey, the latest technology trends relating to microbial functions are summarized to recover and effectively utilize CO2, typical greenhouse effect gas, using microbial functions. Systematic survey and analysis are conducted concerning the microorganisms useful for fixing CO2, CO2 uptake mechanism during the microbial reactions, utilization methods of solar light and useful energy sources except solar light, highly efficient production of useful materials, and usage of produced useful materials. Research has concentrated on use of biological activities for this purpose through design of bioreactors using microorganisms (bacteria and microalgae) for efficient CO2 fixation. For the process to have net CO2 fixation as assessed by its life cycle and to make the process economically feasible, it is essential not only to fix CO2 merely in the form of biomass but in addition to convert it to useful materials by the catalytic activities of the organisms. Three categories were set for the survey, i.e., microorganisms with CO2 fixation ability, available energy for CO2 fixation, and target CO2 fixation products. 169 refs., 49 figs., 14 tabs.

  2. Report on a fiscal 1995 basic survey of the environmental engineering. Investigational survey on the improvement of the waste treatment system; 1995 nendo kankyo business no engineering ka kiso chosa hokokusho. Haikibutsu shori system no kodoka ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-05-01

    The paper described the present situation of the waste treatment system for the environmental engineering and the problems. The final waste treatment plants are in the tighter and tighter condition, and therefore the waste treatment system ought to be changed to a system in which importance is placed on the size reduction, weight reduction, and recycle. Accordingly, the waste treatment system becomes more characterized as a resource feedback process, and should be given more credit as a system for production of secondary resource. The problem is arrangement of conditions of technology, cost and legislation system for smoothing such recycling flow. Of course, it is natural that the most important subject of the system is to secure the environmental preservation by the waste treatment. As future subjects, needed are understanding of the waste treatment as a resource reproductive system, relation with other industries, and review of the legislation system. In consideration of technology, cost and environmental loads, required are proposal of validity of the recycle level limit and a future image of the system structure, and policies for promoting and supporting the recycle business. 47 figs., 104 tabs.

  3. Report for fiscal 2000 on surveys on foundation to establish industrial technology strategy. Surveys on foundation to assist activation of research and development; 2000 nendo sangyo gijutsu senryaku sakutei kiban chosa hokokusho. Kenkyu kaihatsu kasseika shien kiso chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to help discuss the measures to activate researches and developments in private corporations, surveys were made on barriers and factors related to industrial technology research and development by fields, and discussions were given on structuring research and development models. Factors impeding research and development processes relate to a case of each phase in the fundamental research, applied research, and product development, and a case of human resources, funds and information. A policy of structuring models was determined to make quantitative the effects of different aiding systems of the government for researches and developments in private corporations. Case analyses were conducted by using a pilot model. In the present research, a questionnaire survey was carried out to acquire such data as R and D time lag, and to identify the effects of the policies. Surveys were also performed on research and development programs in North America, by making interviews to concerned corporations. As a result of the surveys, such problems were extracted as research and development fund, freer flow of human resources, research and development systems, handling of results of researches performed by consortiums, accounting systems, and sale of the government owned patents. (NEDO)

  4. Fiscal 1998 research report. Feasibility study on next-generation environment-friendly urban transport systems; 1998 nendo chosa hokokusho. Jisedai kankyo kyosei toshi kotsu system donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This research arranges recent public transport system technologies such as LRT, and clarifies their technical issues to be overcome and developmental courses, and the improvement effect of their energy efficiency and CO{sub 2} reduction effect by such measures to contribute to development of next-generation public transport systems. The outlines and features of LRT, monorail/trolley bus and AGT as existing public transport systems are arranged. In the EU, development of tramways using rubber tires is in promotion. The concept of a next-generation environment- friendly urban transport system is prepared based on features of every public transport system. Since a trolley system causes traffic congestion and environment deterioration, introduction of an independent transport system with fuel cell is necessary in the future. The technical issues and solutions for construction of the next-generation transport systems are analyzed. Fuel cell and ITS are important candidates. Substitution of the next-generation transport system for existing buses showed a CO{sub 2} reduction effect of 3.91 Mton/y in Japan. (NEDO)

  5. Fiscal 1999 survey report. Survey of environmental effect pertaining to survey for geothermal development and promotion (Hakusuigoe area); 1999 nendo chinetsu kaihatsu sokushin chosa no uchi kankyo eikyo chosa (Hakusuigoe chiiki) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This survey of environmental effect was intended to grasp actual state concerning some environmental factors that should agree with survey/development and also to assess its effect on the surrounding environment, particularly as a part of the 'stage C' in the 'survey for geothermal development and promotion', which was implemented by the Government for the purpose of guiding geothermal development by enterprises. This report compiles the plan details of the environmental effect survey to be conducted in the Hakusuigoe district, and presents proposals. The survey area is in the north of Makizono-cho, Aira-gun, in Kagoshima prefecture and situated about 3 km west of Onaminoike in Karakunidake, one of the peaks in the Kirishima mountain range. The Ogiri geothermal power plant is in the west of the site, a tourist spot Ebino Heights about 4 km northeast, and the Kirishima hot-spring about 4 km southeast. The location is in the national park, with a part designated as No. 2 and 3 class special areas. The environmental effect survey was divided broadly into such categories as fauna/flora, hot-spring water alteration and inland water, landscape, noise/vibration/subsoil, and air/water, and was further subdivided in accordance with the actual operations. (NEDO)

  6. General evaluation survey report on fiscal 1998 investigation of geothermal development and promotion. No.C-3 Akinomiya area (Third); 1998 nendo chinetsu kaihatsu sokushin chosa sogo hyoka chosa hokokusho. No.C-3. Akinomiya chiiki (dai 3 ji)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-01-01

    With Akinomiya area (11.4 km{sup 2}) selected in Akita prefecture as the survey C area in fiscal 1996, the first survey was conducted. This paper is a summary of memorandum from an advisory standpoint on the evaluation survey concerning the fiscal 1998 investigation results. The contents of the survey are geological investigation, precision gravity exploration, soil gas investigation, electromagnetic exploration, fluid chemical investigation, well drilling and short-term eruption test. An alteration zone was recognized around the place where clay minerals used to be mined, with the center of the zone situated 500-600 m east of a fault. The alteration condition of Akinomiya area seems to be different from that of Doroyu Wasabisawa area. The supplementary gravity survey was carried out at total 58 points in fiscal 1998. It is desirable to set supplementary measuring points over a wide surrounding area for a depth structure analysis. Also performed was a study of mercury concentration in the soil gas. While CSAMT and TDEM methods were employed for the electromagnetic exploration, a suitable method should be carefully selected for a wide area high-density exploration. Consistency with adjacent areas is essential in preparing investigation items particularly for a geothermal model. (NEDO)

  7. FY 2000 report on the investigational study of neutron resistance of high functional semiconductor parts. Summary; Chosa hokokusho. Kokino handotai buhin no chuseisisen taisei no chosa kenkyu(Yoyaku ban)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Soft error induced by cosmic ray was becoming a problem also on the earth surface together with more integration/minuteness of memory device, and therefore, survey of the research trend and extraction of R and D subjects were carried out as to the difference in the state of occurrence of single event upset (SEU) and the evaluation method using neutron beam. Concerning the state of SEU occurrence, survey was made paying attention to the field test, accelerator test and airplane test. There were few reports on the field test, and it was found that it was difficult to arrange environmental parameters. Relating to the mechanism of SEU occurrence, confirmed was a possibility that there was a difference in SEU between proton beam and neutron beam. Further, as to the measurement and simulation of neutron spectra, it was found that there was no enough accuracy. About the evaluation method for neutron beam resistance, it was found that the high energy neutron beam emission device was becoming usable. The paper also outlined the SEU evaluation method. (NEDO)

  8. Feasibility survey of the environmentally-friendly coal utilization system. Feasibility survey of the environmentally-friendly coal utilization system in the Philippines; Kankyo chowagata sekitan riyo system kanosei chosa. Philippines ni okeru kankyo chowagata sekitan riyo system kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    With relation to the coal of the Philippines, where the expansion of the use of coal as a substitute for petroleum/plant fuel is aimed at, the paper grasped the situation of coal production/development, the trend of coal import and domestic distribution, the coal utilization trend, and environmental problems, and analyzed the situation of coal utilization/spread by industry including the commercial/residential use. The purpose of the survey is to draw up a master plan for the introduction of the environmentally-friendly coal utilization system. As to the use of environmentally-friendly coal technology which should be adopted to the coal mining industry and commercial/residential sector, cited are the introduction of coal preparation technology and power transmission technology, and the development/spread of briquette as a firewood substituting fuel. In the electric power sector, the problem is the treatment of ash after combustion and the effective use. Relating to the treatment of flue gas, there is no installation at all of desulfurization facilities and denitrification facilities. In the cement industry sector, they wish to return fuel from heavy oil to coal. For it, it is necessary to study dust preventive measures. In the other sectors, coal hasn`t been used very much. An increase in coal demand is not expected also in the future, and big problems concerning coal haven`t occurred. 42 figs., 64 tabs.

  9. Fiscal 1997 verification and survey of geothermal prospecting technology etc. 2/2. Survey report on deep-seated geothermal resources; 1997 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 2/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-02-01

    For the purpose of reducing the risk to accompany the exploitation of deep-seated geothermal resources, investigations are conducted into the three factors that govern the formation of geothermal resources at deep levels, that is, the supply of heat from heat sources, the supply of geothermal fluids, and the development of fracture systems contributing to the constitution of reservoir structures. In the evaluation and study of reservoirs and the amount of resources, a reservoir simulation is conducted to grasp the characteristics of reservoirs and the amount of resources. For this purpose, the origin and history of the Kakkonda geothermal field are studied, with special attention paid to the origin of the difference in temperature between the shallow-seated and deep-seated reservoirs, the geometry of granite at Kakkonda, the region of recharge of meteoric water, the distribution of saline concentration in the natural state and the cause of the occurrence, the amount of supply of fluids and heat from the depth to the reservoirs, etc. In the evaluation and study of the economic effectiveness of the exploitation of deep-seated geothermal resources, it is learned that, if a 50MW geothermal power station is to be built at a deep level (drilled depth of 3000m on the average) with a rate of 50% attained in drilling, the steam amount required at such a deep level (presumed to be 75t/h) will be more than twice that required at a shallow level (presumed to be 35/h). (NEDO)

  10. FY 2000 report on the survey of the freon recovery/treatment technology for construction use heat insulating materials; 2000 nendo chosa hokokusho. Kenchiku yo dannetsuzai furon kaishu shori gijutsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    An investigational study was made of the quantity of the specified freon remaining in the construction use heat insulating material, the rational method for the recovery/treatment, etc. As to the standardization of the method to analyze the remaining freon quantity, the tube furnace - GC method and the MS method were proposed, and the basic items that can be developed to JIS (Japanese Industrial Standard) were standardized. In the estimation of the remaining freon quantity, the actual state of the use of heat insulating materials was surveyed from the statistics on the start of construction work, survey of the heat insulating area in actual buildings and listening to heat insulation workers/cold store construction companies, etc. Further, the remaining quantity was analyzed of samples collected from various buildings nationwide and by years of completion. As a result, it was found out that, even in samples before 1995, HCFC is used in about 10% and that, in case of limiting to the specified freon (CFC), the freon remaining quantity was more than 1-4 wt% even after a lapse of 30 years. The paper arranged subjects on the freon recovery/treatment in each stage of the life cycle and the required conditions for technology/equipment. (NEDO)

  11. Fiscal 1997 verification and survey of geothermal prospecting technology etc. 1/2. Survey report on deep-seated geothermal resources; 1997 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 1/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-02-01

    For the purpose of reducing the risk to accompany the exploitation of deep-seated geothermal resources, investigations are conducted into the three factors that govern the formation of geothermal resources at deep levels, that is, the supply of heat from heat sources, the supply of geothermal fluids, and the development of fracture systems contributing to the constitution of reservoir structures. In fiscal 1997, a fumarolic gas test is conducted at the deep-seated geothermal well WD-1b which was drilled in the preceding fiscal year. In the test, chemical and isotopic characteristics are compared between the fluids of the WD-1b and the other existing deep-seated wells, and it is found that the fluids from the WD1b originates in surface water just like the fluids from the others and that the constitution of its gas is not greatly affected by magmatic fluids. A PTS (Pressure, Temperature, Spinner flowmeter) logging is performed to observe conditions in the well with the fluids being discharged and to know the inflow point and rate the fumarolic fluids, and the result is utilized to presume the 3-dimensional stress in the vicinity of the WD-1. An isotopic measurement of water included in the fluids is conducted to examine the origin of the geothermal fluids, constant observation and analysis of micro-earthquakes are carried out, and the fluid flow and fluid hydraulic characteristics are also studied. (NEDO)

  12. FY 2000 Research and development of technology for medical and welfare equipment. Report on the comprehensive survey on welfare equipment; 2000 nendo iryo fukushi kiki gijutsu kenkyu kaihatsu chosa hokokusho. Fukushi kiki sogo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The survey is conducted on the advanced basic and application technologies for medical and welfare equipment, e.g., biotechnology and drug delivery systems, to promote development of these technologies. For development of the gene-aided diagnostic system equipment for clinical purposes, surveys are conducted on current medical equipment and related technologies, and the results are summarized and pigeonholed for each equipment type. Also summarized are the small- to medium-sized enterprises which are considered to have techniques needed for development of sensors for heart disease treatment systems. For usability of welfare-related equipment products, investigations are made viewed from the designs oriented to human adaptability, human adaptable designs in the aging societies, and welfare-related problems in the aging societies and usability. The latest information on leading organizations and researchers is collected, for continuation and development of the usability programs for welfare-related equipment products, and also for inviting the current related technologies and researchers on life supporting for the aged in Japan to the programs. (NEDO)

  13. FY 1998 report on the verification survey of geothermal exploration technology, etc. 2/2. Survey of deep geothermal resource; 1998 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 2/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-12-01

    For the purpose of commercializing deep geothermal resource, a deep exploration well of 4000m class was drilled in the existing geothermal development area to survey the situation of deep geothermal resource existence and the availability. Concretely, the deep geothermal exploration well was drilled for study in the Kakkonda area, Shizukuishi town, Iwate prefecture, to clarify the situation of deep geothermal resource existence and the whole image of geothermal system. Consideration was made of the deep geothermal exploration method, systematization of deep high temperature drilling technology, and availability of deep geothermal resource. The results of the survey were summed up as follows: 1) general remarks; 2) deep exploration well drilling work; 3) details of the study. This report contained 3). In 3), the items were as follows: heightening of accuracy of the deep geothermal resource exploration method, making of a geothermal model in the Kakkonda area, study of deep drilling technology, study of deep fluid utilization technology, and making of a guide for deep geothermal resource exploration/development in the Kakkonda area. As to the technology of high temperature deep geothermal well drilling, studies were made of the borehole cooling method, mud water cooling method, survey of deterioration of casing with age, etc. (NEDO)

  14. Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education (civil engineering); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (Doboku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, surveys and discussions were given on the external accreditation system for engineer education such as in universities and other organizations. In the field of civil engineering, a special sub-committee was organized, and in advance to a trial examination, surveys and discussions were executed by participating in the actual examination of the engineer educational program at the engineering department of Auckland University, and by participating in the ABET trial examination by the civil engineering department of Kansas State University and the engineering department of Stanford University in the U.S.A. The trial examination was performed upon selecting the engineer educational programs of the civil engineering department of Kinki University and Tottori University. This paper describes the fundamental policies on the educational program examination work for the field of civil engineering, the self-assessment under the educational program, the direction of engineering qualification and educational accreditation, the fundamental concept of examination and accreditation and evaluation process, the works done by the civil engineering section of the science and engineering department of Kinki University, and the works done by the civil engineering section of the engineering department of Tottori University. (NEDO)

  15. Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education (electronic information communications); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (Denshi joho tsushin)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, surveys were performed on the external accreditation system for engineer education such as in universities and other organizations. In the field of electronic information communications, a committee to correspond to JABEE was established to perform system build-up, where the discussions were advanced. This field was classified into the following four specified areas: general aspect of electric/electronic/information communication engineering, electronics, information communications, and information systems. A supplementary explanation was given on the educational contents except for the information systems, based on which the self-assessment criteria and the evaluation table (for trial use) were prepared. For the examiner training, instructors were invited from ABET in the U.S.A., and training meetings were held. In addition, two committee members were sent as observers to the examinations being carried out at ABET. The trial experiments were conducted for the information communications program at the engineering department of Niigata University, and the electronic system engineering class at Sendai Radio Wave Industrial College. This paper summarizes the results of the examinations. (NEDO)

  16. Research report for fiscal 1998. Basic research for the promotion of joint implementation etc. (Ryazanskaya thermal power station modification program); 1998 nendo kyodo jisshi nado suishin kiso chosa Ryazanskaya karyoku hatsudensho kaishu keikaku chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Under study is the modification of the four antiquated 300MW brown coal-fired power plants of the Ryanzanskaya thermal power station. Under the modification program, the plants will be burning a mixture of 60% coal and 40% natural gas for an increase in efficiency and for a great decrease in greenhouse gas emission. The amount of greenhouse gas emission of 6,858,592 tons/year before the modification will be reduced by 19.4% to 5,532,198 ton/year. The budget for the modification will call for 719,731,700 US dollars. EIRR (economical internal rate of return) is calculated based on the figures provided by the Russian office concerned about the current fuel cost and the current rates for the supply of electricity and heat. It is found that EIRR fluctuates depending on the ruble/dollar exchange rate. Although it does not pay at the current exchange rate, yet, when a US dollar is worth 13.0 rubles, an EIRR of 15% will realize at an availability factor of 70%. The same result is obtained when the availability factor is 80% and a US dollar is worth 14.8 rubles. There is a plan to fire the plants with 100% natural gas in the future. If the plan is implemented, a modification to incorporate gas turbine combined cycle will become feasible. (NEDO)

  17. Report on the survey of geothermal development at Okushiri Island, Hokkaido. Geochemical survey (GC/MS and MS method); Hokkaido Okushiritou chinetsu kaihatsu chosa chikagaku chosa (GC/MS and MS ho) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-09-01

    To elucidate chemical components of soil gas in the Okushiri Island area, soil gas was collected by the method using charcoal adsorbent, and analysis was made by the GC/MS method. Out of the 19 measuring points, 17 points were set up near the measuring points in the FY 1998 survey by the finger print method. At the same measuring points, analytical survey by the MS method was also conducted to sort the type of soil gas. As a result of the GC/MS analysis, xylene or ethyl benzene was detected at 12 measuring points of all 19 measuring points, and from the distribution, it was predicted that there were anomaly zones in the district along the road of the Okushiri Island line and the district southward from the 5.8K Pass. These results were in harmony with the results of the survey by the finger print method. As to the sorting of soil gas based on the results of the MS analysis, the results were different at 8 measuring points from those of the survey by the finger print method in FY 1998. It was considered that the cause was the accidental vaporization of a large quantity of acetaldehyde, and acetaldehyde was regarded as a noise gas component that does not reflect the geothermal structure. (NEDO)

  18. Investigation of geothermal development and promotion for fiscal 1997. Investigation report on geological/alteration zone (No. B-5 Musadake area); 1997 nendo chinetsu kaihatsu sokushin chosa. Chishitsu henshitsutai chosa hokokusho (No.B-5 Musadake chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This investigation was intended to clarify the possibility of existence of geothermal reservoir layer by elucidating the underground structure and thermal source forming the geothermal system around Musadake, in the area extending over Nakashibetu-cho and Shibetu-cho, Shibetu district, Hokkaido, and further by grasping the distribution and properties of the geothermal alteration zone. The geothermal system of the subject area seems to be governed by Musadake - Mt. Shitabanupuri fault, its incidental bent zone, and the graben extending to the southeast side. The thermal source is presumably a magma reservoir that evolved Musa volcano. The depth hot water is presumed to exist in the underground depth around Mt. Imora; and it seems that the thermal conduction and volcanic ejecta are caused by a chain of volcano-related magma reservoirs around Musadake, the thermal source presumably. The depth hot water is estimated to be not less than 250 degrees C and a high Cl concentration. Within the graben, mudstones are distributed such as Kawakita layer and Yokoushigawa geological layer. Moreover, it is possible that an impermeable layer due to alteration is spread. (NEDO)

  19. Report on surveys in fiscal 2000 on the survey on foundation to establish industrial technology strategy. Survey on lifetime education for mechanical engineers; 2000 nendo sangyo gijutsu senryaku sakusei kiban chosa hokokusho. Kikai gijutsusha shogai kyoiku chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective to set up a system for full-scale lifetime education, a feasibility study has been performed on preparing new educational materials and performing seminars. The continuing education program developed by the Japan Society of Mechanical Engineers is intended to assist engineers studied under the new engineer system to accumulate actual work experience after having acquired the qualification, and motivate ability maintenance and self-enlightenment after having acquired the engineer qualification, mainly through the training meetings and lecture meetings held by the Japan Society of Mechanical Engineers. The education items in the major field course include dynamics of materials and machines, energy and flow, information and control, and design and production. The items in the general common course include presentation and communication, kinetics learned from actual cases, engineer ethics, product liability and product safety. The seminar was held for two days for engineers graduated from undergraduate departments and experienced in actual works for two years or longer as the object. The actual status survey related to the continuing education by corporations revealed that 83% of the corporations has implemented intra-corporation training, and encouraged positive participation to outside seminars. (NEDO)

  20. Fiscal 1999 geothermal development promotion survey. Structural boring survey work and analysis report (No.B-6 - Tsujinodake area); 1999 nendo chinetsu kaihatsu sokushin chosa. Kozo shisui chosa koji oyobi kaiseki hokokusho (No.B-6 Tsujinodake chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-12-01

    Cuttings from bores N11-TD-2 and N11-TD-3 drilled for the purpose of confirming the existence of geothermal resources in the Tsujinodake area were examined and tested, and the results of temperature logging, electrical logging, and water injection tests carried out during the structural boring work were analyzed. Activities were conducted in the four fields of (1) test boring work, (2) survey and measurement, (3) core cutting examination, and (4) comprehensive analysis. In bore N11-TD-2 positioned in the northern part of Tsujinodake, a sharp temperature rise was detected in the clay converted alteration zone between 200m above sea level and 200m below sea level. A high temperature of 215 degrees C was recorded at 200m below sea level, and it was found that high temperature geothermal water was in reserve at the bottom of the clay converted alteration zone between 100m above sea level and 200m below sea level. In bore N11-TD-3 in the southern wall of the Ata caldera, a convection type low temperature profile was observed at a shallow level and low temperature convection of underground water was detected there. (NEDO)

  1. FY 1998 geothermal development promotion survey. Report on the environmental effect survey (animals/plants, No. B-7 Kuwanosawa area); 1998 nendo chinetsu kaihatsu sokushin chosa. Kankyo eikyo chosa hokokusho (doshokubutsu, No.B-7 Kuwanosawa chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This survey was conducted to estimate effects of drilling of geothermal exploration well on the environment, aiming at grasping the present state of environmental elements before the survey/development. As a result of the literature survey, the following distribution were confirmed in the fauna: 5 orders 10 families 19 species in the mammalia, 10 orders 25 families 73 species in the aves, 1 order 3 families 6 species in the reptilia, 2 orders 6 families 9 species in the amphibia, and 17 orders 179 families 719 species in the insecta. In the flora, a distribution of 132 families 670 species was confirmed. The results of studying the above indicated that in the fauna, there were 10 species such as antelope as valuable animal in the area surveyed and that it is necessary to pay much attention to the environmental preservation of the habitat for those animals in the well drilling associated with geothermal survey. In the flora, the 13 valuable animals selected as animal having a fear of extinction in the 'plant-version red list' were confirmed in the area surveyed and the periphery. Further, as to the plant colony, there are no important colonies in terms of preservation. In well drilling, important things are efforts exerted to restore to the original state of the area altered, prevention of the washed-away of mud water, etc., and efforts exerted to preserve the environment of vegetation. (NEDO)

  2. Survey report of FY 1996 on the questionnaires related to new energies for local governments in Kinki district; 1996 nendo chosa hokokusho (shin energy ni kansuru Kinki chiiki jichitai anketo chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The photovoltaic (PV) power generation system having a lot of merits for environment and energy has been put into a diffusion stage from the viewpoint of its technology due to its progressive technology innovation. However, it is not widely diffused in the whole society due to its high cost. Systematic investigation for the future PV power generation was conducted through the verification of factors obstructing the diffusion promotion and the investigation of the problems. Then, questionnaires were conducted for local governments in the Kinki district. Proportion of the local governments positively promoting the introduction of PV power generation was 3.4%. Among new energies, 45.7% of the governments were interested in solar heat utilization, and 43.1% were interested in PV power generation. Proportion of the local governments understanding the subsidy system of MITI was 57.7%. For the explanation meeting of new energy introduction promotion, 55.4% of the local governments wanted to participate. Among the interesting themes, 61.0% were interested in the introduction examples, 52.4% were in the introduction support, 52.1% were in the introduction of fundamental knowledge, and 30.0% were in the latest technology trends and in the guide for introduction

  3. Research and survey report of FY 1997 on the CO2 balance for high-temperature CO2 fixation and utilization technology; 1997 nendo chosa hokokusho (nisanka tanso koon bunri gijutsu ni okeru CO2 balance ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The purpose of this research is to clarify the application condition and effectiveness of high-temperature CO2 fixation and utilization technology. To evaluate the present process, it was compared with others, such as separation using a polymer membrane, physico-chemical absorption process, adsorption process, hydrogen contact reduction process, and biological fixation. The development trends of absorption, membrane, adsorption, and cryogenic separation were investigated. The questionnaire was carried out about the separation technologies which are in the stage of performance test using actual gas, to arrange and compare the data and information. The current trends of chemical and biological CO2 fixation and utilization technology were also investigated for arranging the subjects. High-temperature CO2 disposal by the carbonation in concrete waste has been studied, to clarify its application conditions and effectiveness. In order to compare the separation technologies, treatment processes of CO2 in the exhaust gas from boilers of LNG power generation and coal fired power generation were simulated. These processes were simulated by ASPEN PLUS for the modeling. Trends of application of ASPEN PLUS and collection of information were surveyed by participating in the ASPEN WORLD. 103 refs., 51 figs., 55 tabs.

  4. Fiscal 1997 report on the survey project on planning to execute `The New Earth 21`; 1997 nendo chosa hokokusho (`chikyu saisei keikaku` no jisshi keikaku sakusei ni kansuru chosa jigyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Japan proposed in the Houston Summit the New Earth 21 to be carried out with technology development and technology transfer, and to make a concrete development of the project, Japan also proposed in the Tokyo Summit a TREE Plan for working out comprehensive strategies of the innovative technology development. In the CO3 Kyoto Conference in 1997, numerical targets for developed countries were determined which have legal binding force for control/reduction of greenhouse gas emissions in the term of 2008-2012. It was agreed to urge developing countries also to play a certain part in the project through the clean development. Therefore, the paper made quantitative analysis of important CO2 prevention technologies, technology transfer costs, and economical assessment by energy conservation. As a model, the DNE 21 model was upgraded and used into which CO2 prevention technologies, energy, economy and climate changes were integrated. In fiscal 1997, the following were carried out: collection of data on important CO2 prevention technologies and systems and analytical assessment using the DNE 21 model, CO2 reduction and selection of energy technology, assessment of energy system costs, construction of the unified DNE 21 model, and opening of the international workshop. 62 refs., 98 figs., 34 tabs.

  5. Report on fiscal 2000 survey for geothermal exploration technology verification. Survey of deep-seated geothermal resources; 2000 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    To promote the development of deep-seated geothermal resources in a rationalized way, studies are conducted about deep-seated geothermal resource assessment techniques, development guidelines, and the like. Data were collected at the Sumikawa-Onuma district, Ogiri district, Mori district, Yanaizu-Nishiyama district, and the Onikobe district, and compiled into a database to be open to the public. Studies were made about methods for estimating parameters for deep-seated geothermal reservoirs. The resultant findings indicate that, in the Uenotai and Sumikawa-Onuma districts where geothermal reservoirs are governed mainly by a fracture network, the relaxation method and extrapolation will be effective for deep-seated reservoir temperature estimation, and the ascending current analysis method and extrapolation for permeability estimation. The findings also indicate that the expanse of deep-seated reservoirs will be suitably estimated using a method similar to that applied to shallow-seated reservoirs. In the study of the estimation of the amount of deep-seated geothermal resources, it is concluded that the simplified model A will be effective in dealing with a geothermal district where there is a well-developed fracture network and the simplified model B in dealing with a geothermal district where supply of deep-seated fluid governed by an extensive fault prevails. (NEDO)

  6. Basic project on the cooperation in enhancement of the international energy consumption efficiency. Survey of energy conservation potential by industry; 2000 nendo kokusai energy shohi koritsuka chosa nado kyoryoku kiso jigyo hokokusho. Gyoshubetsu sho energy potential chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of looking for measures to promote the effective energy conservation in China, the potential energy conservation amount in general plants was surveyed and analyzed by industry. Activities were made in the following fields: 1) survey of the actual state of energy in main industries; 2) energy conservation potential in the cement industry in China; 3) energy conservation potential in thermal power plants in China. In 1), survey was made on 8 industries including the iron/steel industry and oil refining industry. In 2), survey was made of the actual state of the Liulihe cement plant and Shitou cement plant. The subjects extracted were the arrangement of instrumentation equipment such as the exhaust gas analyzer needed for combustion management, improvement of the air/fuel ratio of kiln, enhancement of cooling efficiency of clinker cooler, etc. In 3), the actual state of the Qinling power plant was surveyed, and it was made clear that high efficiency of 38% or more can be maintained if the appropriate use/maintenance management is made (coal unit consumption: 383g/kWh in Qinling and 309g/kWh). (NEDO)

  7. Report on the FY 1992 basic survey for industrialization related to the survey of overseas geological structure (Embalut West area, Indonesia); 1996 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa hokokusho (Indonesia Embalut nishi chiku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    The paper reported the FY 1992 basic survey for the coal mine development/industrialization in the Embalut West area of Indonesia. The geological structure in the survey area is under the Loa Haur Syncline which lies approximately north and south to the west of the area, and is regarded as the stabilized structure having no faults. The three beams from the upper part, S14, S13 and S12, are assumed to be the coal seams to be drilled. The average seam thickness is 1.17, 2.35 and 3.09m, respectively, and the continuity is good. In S14 beam, which is thin, it is difficult to mine coal using equipment. The theoretical minable reserve of the three coal seams is 18,859,000 tons. The recoverable coal reserve is 12,258,000 tons at a mining recovery of 65%. In case of annual production of 0.4 million tons, it is possible to mine more than 30 years. The coal is classified into a subbituminous coal-brown coal rank of the JIS coal classification. It is high in water content and medium in heating value, but is an environmental protection type with low ash and low sulfur content. In the case of mines in the Mahakam River basin, barge transport is indispensable. For sea transportation, the following should be studied in the light of the international price competition: reinforcement of shipping facilities on Mahakam River, increase in barge size, joint use of Balikpapan Coal Center, etc. (NEDO)

  8. Report on the FY 1998 geological structure survey. North Hay Gulch area, State of Colorado, the U.S.; 1998 nendo kaigaitan kaihatsu kanosei chosa hojo jigyo chishitsu kozo chosa hokokusho. Beikoku Colorado shu North Hay Gulch chiiki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-02-01

    Test boring at 21 places and core sampling were conducted during September-November 1998 along the ridge to the west of Hay Gulch and in the direction crossing the northwest of the drainage canal and National King Coal Mine (NKC coal mine). It was found that A layer which NKC coal mine is now drilling is the upper part of A coal seam where the seam bifurcates. The boundary to the west of the thick A coal seam is not clear, and there is a possibility that more reserve from the thick coal seam and single seam exists toward Cherry Creek. In the existing coal drilling area, the lower A seam existing under the upper A seam becomes thin rapidly, and the seam thickness becomes less than 1 foot. The average thickness of thick coal seams is 9.9 feet, and the area is 780 acres along the ridge. The upper A coal seam except the above is 5.5 feet in average seam thickness and 910 acres in area. The reserve is 23 million tons. As to the quality of thick coal seam, the average heating value is 7,089 kcal/kg, sulfur content 0.68%, and ash content 7.50%. As coal drilling conditions, the same level as or higher than those of NKC coal mine is expected. (NEDO)

  9. Fiscal 1996 verification and survey of geothermal prospecting technology etc. 1/2. Survey report on deep-seated geothermal resources; 1996 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 1/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of reducing the risk to accompany the exploitation of deep-seated geothermal resources, investigations are conducted into the three factors that govern the formation of geothermal resources at deep levels, that is, the supply of heat from heat sources, the supply of geothermal fluids, and the development of fracture systems contributing to the constitution of reservoir structures. In fiscal 1996, the deep-seated exploration well WD-1a is sidetracked for penetration for a target newly assigned at the 3,000m-deep level. Carried out in a survey of well geology are the naked-eye and microscopic observation of core cuttings, X-ray powder method, examination of inclusions in fluids, chemical analysis of whole rocks, analysis of isotopes in minerals, analysis of core fracturing, etc. Also, data are collected from a survey of mud log, survey of water in the well before digging, and from well logging. Furthermore, pressure monitoring etc. are conducted in order to determine the interference in pressure between the deep-seated and shallow-seated wells that accompanies multiple outbursts from the Kakkonda No. 2 machine, to know the water permeability between the shallow-seated and deep-seated parts, and to grasp the anisotropy in permeability in shallow-seated reservoirs. (NEDO)

  10. Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education (general); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (Zentai)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, trials and discussions were performed on the external accreditation system for engineer education such as in universities and other organizations. The current fiscal year has performed the trials of examination and accreditation at 19 universities and for 20 programs covering eight fields including chemistry, machinery, civil engineering, electrical, electronic, information communications, information processing, materials, resources and agricultural engineering. In performing the trials, the purpose and the basic policies were identified, the guidebook for actual examinations was prepared, and the program check book and the trial examination report were also compiled. Two assembly training meetings were held to train about 130 examiners, of which 65 examiner chiefs and examiners have participated in the trials for 20 schools to work for the examination. As a result of the trials, the training was found capable of having served for improvement of the engineer education program in high-level education institutions, and improvement of the accreditation criteria and examination methods to establish the external accreditation system. (NEDO)

  11. FY 2000 report on the basic survey to promote Joint Implementation, etc. Survey on the energy conservation of the Lianyuan Iron and Steel Group Complex, China; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Lianyuan tekko sho energy chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of conserving energy and reducing greenhouse effect gas emission, a feasibility study was carried out of the installation of energy conservation facilities at the steelworks of Lianyuan Iron and Steel Group Complex, Loudi City, Hunan Province, China. The installation of the following facilities was studied: coke dry quenching (CDQ) equipment, coal moisture control (CMC) equipment, sintering ignition furnace equipment, cooler exhaust heat recovery equipment, top pressure recovery turbine (TRT), and hot stove exhaust heat recovery equipment. As a result of the study, the energy conservation amount was 20,000 toe/y by CDQ, 2,530 toe/y by CMC, 900 toe/y by improvement of ignition furnace in the sintering process, 12,300 toe/y by sintering cooler, 13,200 toe/y by TRT, and 10,300 toe/y by hot stove exhaust heat recovery equipment. Further, the amount of greenhouse effect gas reduction was 61,022 t-CO2/y, 7,843 t-CO2/y, 2,896 t-CO2/y, 38,060 t-CO2/y, 55,295 t-CO2/y, and 40,621 t-CO2/y, respectively. In the estimation of effects vs. expenses, the sintering ignition furnace, sintering cooler exhaust heat recovery, and hot stove exhaust heat recovery indicated the comparatively favorable values. (NEDO)

  12. Fiscal 1998 research report. Research on the possibility of promoting CDM project through technology transfer with plant exports; 1998 nendo chosa hokokusho. Plant yushutsugata gijutsu iten wo tsujita CDM project suishin kanosei ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Study was made on promotion of CDM (clean development mechanism) project through technology transfer with plant exports. Although CDM system was provided in COP3 on climate change held in Kyoto in 1997, its detailed rules including project approval are yet undecided, and only the schedule to provide the detailed rules until COP6 in 2000 was decided in COP4 in 1998. The common recognition that the CDM project with plant exports produces various merits for both Japan and the partner country is increasing. However, from the viewpoint of forming concrete CDM projects, most Japanese enterprises are passive in approach to the CDM project because of no detailed design of CDM, uncertain profitability and procedures, and avoidance of additional burdens. Plant export is also difficult because of the fact that assessment of a new project is difficult. Enterprises' deeper recognition on the CDM project, and a governmental integrated support system are desirable. (NEDO)

  13. Fiscal 1997 report on a feasibility survey of cooperation in relation to the joint implementation activities in Southeast Asian countries (6 nations); 1997 nendo chosa hokokusho (Tonan Asia chiikikoku (rokkakoku) ni okeru kyodo jisshi katsudo kanren no kyoryoku kanosei chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In the COP3 Conference on Global Warming held in Kyoto in December 1997, the framework on greenhouse gases was agreed in discussions comprehensively made among Japan, the U.S. and the E.U. As a result, it is for 6 gases including CO2 and methane, and total emissions in developed countries are to be reduced 5% at least during 2008-2012 from the 1990 level. Target of each country is determined by gaps, and Japan`s reduction target is 6%. Therefore, to pass the numerical target agreed, it is necessary to take measures such as rationalization of the energy use by energy saving, etc. in the country and also measures such as promotion of the greenhouse gas emission control in developing countries. Accordingly, for the future development of NEDO`s AIJ project, a possibility of cooperation in the joint implementation was surveyed such as the state of greenhouse gas emissions of countries which are objects of GAP in Southeast Asian countries and neighboring countries, policies of the countries after the COP3 agreement, technological transfer for the emission control, etc. Countries for survey are Thailand, Indonesia, the Philippines, Malaysia, Vietnam and Myanmar. 21 figs., 15 tabs.

  14. Fiscal 1994 survey of the base arrangement promotion for foreign coal import. Investigation on the trend of coal demand in Central and South American countries; 1994 nendo kaigaitan kiban seibi sokushin chosa. Chunanbei shokoku ni okeru sekitan jukyu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Focusing on the present status and future of coal demand in Central/South American countries and the coal trade between Central/South American countries and the U.S., the paper described the present status and future of coal demand there and the effects on Japan. Export of Colombian coal will amount to approximately 30-35 million tons in 2000. Venezuelan coal 10-20 million tons. The U.S. imported good-quality general coal low in sulfur content, 3.08 tons from Columbia and 1.39 tons from Venezuela. Coal export from the U.S. to Central/South America was mostly of raw material coal, 5 million tons in 1993 and 5.39 million tons in 1994. General coal was 180,000 tons. The U.S. has no plans of increasing US coal export to Central/South America. But it is safely predicted that Columbia and Venezuela will increase coal export to Europe in the future. It will bring about decrease in export of US coal to Europe, which connects with increasing pressure for the coal trade amount of Japan. 21 figs., 47 tabs.

  15. Report for fiscal 1998 on basic commercialization survey related to geological structure surveys in overseas countries (Manguerra, the Philippines); 1998 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa (Philippines Manguerra) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Commercialization survey was performed on the mines in the Manguerra district in the Philippines by means of geological structure surveys. The site surveys included geological and test drilling surveys, and those on conditions for developing underground mining mines, and infrastructures. The geological survey area spread out about 5 km{sup 2}, two test wells were drilled (to depths of 330 m and 290 m), trench survey was performed on 58 locations, and coal sample collection and analysis were carried out on eight locations. Furthermore, surveys were extended to the Manguerra mine operating status, on-the-ground facilities, roads for transportation, marketing, and related laws and regulations. As a result of the surveys, the Manguerra district was suggested of frequent sea water inundation into the coal field, leading to a view that the district is unstable from the viewpoint of development of coal beds. However, samples collected from the existing mining area indicated to have less water content and ash and high calorific power. The coal has high product value. The result of coal quantity calculation indicated 320122 tons as the total of defined and estimated quantity. The great depth mining plan was prepared from the viewpoints of actual yield, productivity, safety aspects, technological enhancement, and suppression of additional investments to minimum. (NEDO)

  16. Fiscal 1997 survey report on technology to reduce the amount of greenhouse gas emitted from automobiles; 1997 nendo chosa hokokusho (jidosha kara no onshitsu koka gas haishutsuryo teigen gijutsu no chosa). 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    As to intelligent transport systems (ITS), the paper views the outline of the R and D and diffusion in Europe, the U.S. and Japan and trially estimated the effect of reduction in greenhouse gas, and worked out visions/scenario for diffusion of ITS. As developmental fields contributing to reduction in greenhouse gas, the following were taken up: 1) AVCS (advanced vehicle control system), 2) automatic rates receiving system, 3) traffic management, 4) plans of operation management/allocation of commercial cars, 5) modal shift of the material flow, and 6) public traffic in passenger transportation. As effects by developmental field, 1) and 5) are especially effective. 4) is promising because of its easiness in introduction, and 2) is also a promising technology as a tool to introduce an electronic road pricing system on general roads in future in addition to the effect of reducing heavy traffic by its introduction to expressways. However, the higher the service level on the facility side becomes, the more the traffic demand amount becomes. By how to introduce ITS, it possibly occurs that improvement of the situation will not be made at all on the future vehicle traffic system. 38 refs., 42 figs., 52 tabs.

  17. Fiscal 1999 geothermal development promotion survey report. Structural boring survey work and analysis (No. B-5 - Musadake region); 1999 nendo chinetsu kaihatsu sokushin chosa. Kozo shisui chosa koji oyobi kaiseki hokokusho - No. B-5 Musadake chiiki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-12-01

    For geothermal development in the Musadake region, Shibetsu-gun, Hokkaido, structural boring was carried out and boreholes were inspected. In the structural boring survey, borehole N11-MD-3 was drilled as deep as 2,001.18 m, and borehole N11-MD-4 2001.44 m. Performed or tested for each of the two boreholes were temperature logging, electrical logging, temperature recovery, reinjection, core cutting examination, and so forth. The result of the temperature logging shows that temperature rise is slower at levels deeper than 1280 m in borehole N11-MD-3, with the maximum temperature marking 274 degrees C, and, in borehole N11-MD-4, the maximum temperature is 198 degrees C. No reinjection test is carried out because the ground pressure is too high to allow the replacement of the borehole content with fresh water. Analysis results lead to a conclusion that the hot fluid in this region originates in fossil seawater and in meteoric water, the latter arriving after a long-term permeation process, heated by thermal conduction to 270 degrees C or higher. It is inferred that the geothermal fluid flows in a fissure in the vicinity of the Musadake/Mt. Shitabanupuri fault and a fault orthogonally crossing the said fault for the formation of a high-temperature geothermal storage. (NEDO)

  18. Leading research report for fiscal 1998. Research and study of ozone-aided technologies for creating amenity-rich environments; 1998 nendo sendo chosa kenkyu hokokusho. Ozon riyo kaiteki kankyo sozo gijutsu no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Researches were conducted aiming at the establishment of an ozone-aided highly efficient decomposition process for the persistent organic matters in municipal sewage and industrial wastewater. Tested for verification were advanced water treatment technologies of the biological function acceleration type and the effect of their combination with the accelerated oxidation method, conditions necessary for efficient operation, and water treatment apparatuses and systems for operating them at high efficiency. Some findings are stated below. With an ozone-aided process performed at the first stage of biological treatment, biological decomposition is accelerated for a rise in the persistent organic matter decomposition rate. This is nothing but a finding in the laboratory, however, and much remains to be disclosed concerning the optimum conditions, reforming of sludge to be generated, volume reduction of the same, etc. Another finding involves the acceleration of decomposition of persistent organic matters using ozone in combination with hydrogen peroxide, ultraviolet radiation, titanium oxide, and the like. There still remain numerous tasks to carry out, however, which relate to the investigation of the reaction mechanism, establishment of operating conditions and criteria for selecting oxidants, etc. As for ozone, remaining to be solved are the problems of generation cost, storage and preservation, and safety. (NEDO)

  19. Survey report for fiscal 1998. Survey of trends of new CO{sub 2} fixation technology using bacteria and algae (II); 1998 nendo chosa hokokusho. Saikin sorui wo riyoshita atarashii nisanka tanso kotei gijutsu no doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The trend of technology is surveyed from a standpoint that, in the process of CO2 fixation using microbes for the production of useful substances, it is essential, in view of income/outgo balance and economy, to utilize their catalytic function. The survey centers about the feasibility of the utilization of organic wastes, cellulose wastes in particular, as an energy source. Special attention is paid to the energy of artificial light and laser beams. From a point of view that it is important to suppress cell multiplication and to effectively utilize only catalytic activity for the production of useful substances, the cell division mechanism of the Corynebacterium is analyzed, and the findings are compiled to facilitate the study as to whether the division may be controlled. A report is also prepared on the metabolic mechanism of a photosynthesizing bacterium that is judged to be the most promising species. Reference is made to aerobic and anaerobic bacteria. Shown are the organic compounds that are formed by CO2 gas fixation thanks to microbial or enzymatic reactions. To emphasize their importance as an energy source and to explain the conversion of biomass into useful substances, the technology and economy of conversion into fuel compounds are surveyed. The production of ethanol out of organic wastes is evaluated in the way of LCA (life cycle assessment). (NEDO)

  20. FY 2000 survey on technical trends. Survey of technical trends on materials for heightening of performance for power generation facility use; 2000 nendo gijutsu doko nado chosa. Hatsuden shisetsuyo koseinoka zairyo ni kakawaru gijutsu doko nado chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As to high performance/high function plastic materials used in power generation facilities, technical trends were surveyed on the recycle situation and recycle R and D to study the subjects to be solved. For wire covering materials, vinyl chloride, polyethylene, rubber, etc. are used, and the recycle of resin has not been advanced. Concerning the generation of waste plastic, the existence of a lot of plastics different in characteristics makes the recycle difficult. As to the use of waste plastic as resource, the material recycle and recovery of combustion energy are being made, but only a part of the plastic is reused as chemical raw materials. Relating to the R and D of the chemical recycle technology, there are sample studies on the pyrolysis of polyolefine, dechlorination of chlorine base resins, etc. Recently, the following have been made public: proposal of depolymerization monomer based on the cyclic monomer, study of liquefaction of approximately 100% of the thermosetting resin, approach to the solvolysis by supercritical solvent. (NEDO)

  1. Survey report on project for drawing district energy-saving visions for Town of Aizu Wakamatsu. Preliminary survey; 2000 nendo Aizu Wakamatsu shi chiiki sho energy vision sakutei nado jigyo (shoki dankai chosa) chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    The feasibility study is conducted for introduction of the district energy-saving measures in City of Aizu Wakamatsu, for which the actual situations of energy consumption and promising energy-saving measures are surveyed. The city has a typical basinal weather, cold in winter and very hot and humid in summer, and tends to have a longer air-condition period in a year. It is considered that there are many wasteful energy consumption items to be studied for reduction. In the area of moving means, dependence on public transportation systems is considered to be relatively low, suggesting that there are much space of reducing transportation energy by the measures such as self-imposed control on use of private cars, promotion of utilizing public transportation systems and fuel-saving type driving throughout the city. The promising energy-saving measures studied to verify the effects include introduction of PVM analyzers for establishing better cost/effect relationship between power consumed by air-conditioners and pleasantness; introduction of garbage power generation, co-generation and high-efficiency illuminators; improvement of power-factor; and demand control for air conditioning, rationalization of power-receiving facilities, introduction of systems for saving flushing water and improvement of air conditioners' outdoor facilities. (NEDO)

  2. Fiscal 1996 survey for the upgrading of the Asia/Pacific coal development. Survey of the coal infrastructure propagation in Indonesia; 1996 nendo Asia Taiheiyo sekitan kaihatsu kodoka chosa. Indonesia ni okeru sekitan infura seibi chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-01

    Phase 1 survey in fiscal 1996 was conducted based on `Agreement on the comprehensive survey of a coal transportation system in South Sumatra` concluded between NEDO and the Ministry of Mine and Energy in Indonesia. In the survey, conducted were collection of data on coal fields and site surveys, collection of data on inland transportation and site surveys, collection of data on harbors and site surveys, and worked out were a simplified database and a coal transportation plan by optimization of the coal chain system. The area for survey is the periphery of the Musi River of South Sumatra. The results of the simulation by LP models were as follows: When the coal of Bukit Asam coal mine is $25/t in price, only coal of 5500Kcal/kg is profitable, and when $27/t in price, coal of 4500Kcal/kg also becomes profitable. This shows that if the coal is of good quality, it can pay arriving at Suralaya, independent of the distance of transportation. 47 figs., 63 tabs.

  3. 1998 Annual Study Report. Surveys on seeds for global environmental technologies, including those for energy saving; 1998 nendo chosa hokokusho. Sho energy nado chikyu kankyo taisaku gijutsu no seeds ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The energy-saving and other global environmental technologies are surveyed by collecting relevant information from various institutes, both abroad and domestic, to contribute to development of ceramic gas turbines. USA has announced a climate change plan, based on the five principles, to promote utilization of high-efficiency technologies and development of new clean technologies. UK is promoting to improve energy efficiency, along with liberalization of its energy markets. Germany concentrates its efforts in the 'Program for Energy Research and Energy Technologies.' France places emphasis on prevention of air pollution and rational use of energy. The R and D trends at public institutes, e.g., universities, for global environmental technologies are surveyed, from which a total of 14 themes are extracted as the seed technologies. At the same time, a total of 9 techniques potentially applicable to the seeds are extracted by mainly reviewing JICST and patent information, and assessed. The R&D trends of the IPCC-related researchers are also surveyed, but provide no theme directly applicable to the seeds. Most of the related themes at the private and public institutes surveyed, both domestic and abroad, are concentrated on carbon dioxide. (NEDO)

  4. Basic research on promotion of joint implementation. Research on the overseas trend of activities implemented jointly; Kyodo jisshi suishin kiso chosa jigyo. Kyodo jisshi katsudo ni kakawaru kaigai doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The pilot phase of the activities implemented jointly (AIJ) was approved in 1995 in the 1st Conference of the Parties (COPI) of the United Nations Framework Convention on Climate Change to reduce greenhouse gas emission. In order to promote the AIJ Japan program smoothly, some practical examples in every preceding country and the situations and demands of Asian countries were researched. It was confirmed that since larger cost-effectiveness is achieved just in countries lower in emission control cost, AIJ can enhance the cost-effectiveness and promote environmental technology transfer. Japanese government had studied establishment of the framework for AIJ, and decided the basic framework of the AIJ Japan program in 1995. The government also approved the evaluation guidelines of this program which include confirmed and considered matters necessary for government offices related to this program to evaluate and approve each project.

  5. Research report for fiscal 1998. Research about feasibility of CO{sub 2} reduction program construction for Pan-Japan sea resources; 1998 nendo chosa hokokusho. Kannihonkai shigen CO{sub 2} sakugen program kochiku kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The research aims to construct a recyclable resources distribution network in coordination with other Japan Sea countries so as to establish measures for the effective utilization of resources originating in Japan. The research covers the needs in China and in Russia's Far East provinces for used electrical home appliances and the supply capability of Japan's four prefectures on Japan Sea including Akita Prefecture. Demand in the countries on the other side of the sea for three major categories of electrical home appliances (color television sets, washing machines, and refrigerators) for 2010 and 2025 is predicted. Part of the predicted demand is specified to be for used items, and a scenario is built based on the reuse substitution rate. On the other hand, in view of the life time of such commodities and the rate of reusables in the amount of waste generated, a conclusion is reached that probabilities are that all such appliances from the four Japanese prefectures will be put to reuse. When the reuse rate is estimated at 10% for goods under the three major categories from the four prefectures, approximately 20,000 articles out of each of the three categories will be put to reuse, and this will lead to a reduction of CO2 emissions of 7700 tons a year. (NEDO)

  6. Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education (information); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (Joho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, surveys and discussions were performed on the external accreditation system for engineer education such as in universities and other organizations. In the survey on the information field, a trial was attempted on the information related course at Kyoto University and Osaka University based on the accreditation criteria discussed with an objective of establishing the external accreditation system. The trial was performed on computer science for Kyoto University and software engineering for Osaka University. The activity has provided the examiner side with an opportunity to actually experience the accreditation work, and the examiners had a feeling that the work can help improve the education. The side receiving the accreditation indicated problems in the present system including the concern about the system becoming a mere shell. In addition, participation in the accreditation examiner training work for the information field in the U.S.A. has provided useful information such as thoroughgoing observation of the duty of confidentiality. (NEDO)

  7. FY 1999 report on the study of the future course, etc. of 'the basic survey for promotion of Joint Implementation, etc.'; 1999 nendo 'kyodo jisshi nado suishin kiso chosa' no kongo no hokosei nado ni kansuru kento chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The paper conducted the demonstration of the multiplier effect of 'the model project for heightening of the international energy consumption efficiency, etc.' carried out by NEDO and its subsidiary project, 'the project on the basic survey for promotion of Joint Implementation (JI),' and the comparative study between these projects and the JI/CDM projects proposed in the world. In the quantitative evaluation of the multiplier effect, in the case of making the demonstration of the same technology in the same area both in the model project and the basic survey for promotion of JI, it becomes possible to grasp the CO2 reduction effect with high accuracy, but the CO2 reducible amount is small. Inversely, as to the technology for which the basic survey for promotion of JI is studied, but the model project is not carried out, it becomes possible to grasp the CO2 reduction effect with low accuracy, the CO2 reducible amount is large. In the comparison with the JI/CDM projects proposed in the world, the CO2 reduction amount was approximately $2.7 billion, 250 million tons, in the UNFCCC project, and approximately $5.0 billion, 500 million tons, in the IJ project. There was no very big difference in the cost effect. (NEDO)

  8. FY 1999 report on the investigational study of the actual state of the utilization of clean energy vehicles for the transport business use; 1999 nendo chosa hokokusho. Unso jigyo yo clean energy jidosha no shiyo jittai ni kakawaru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of promoting the utilization of clean energy vehicles (CEV), survey was made on the assessment of the pollution by the CEVs introduced by now, subjects on the utilization, etc. As to the transport business use CEV running in the market, CNG vehicle is mostly used, and therefore, the gas emitted from them was tested. As a result, it was found out that CNG vehicle emits fewer NOx, PM and soot/smoke than diesel cars and contributes to improving the air pollution in large cities. However, it emits more CO2 than diesel car, and accordingly, it is necessary to reduce the fuel consumption. The practicality in the limited running distance is almost the same as that of diesel car, but it is desirable to improve startability, acceleration and gradability. Further, the occurrence of any troubles was pointed out in a third of the total numbers of CEV vehicle. Improvement in reliability is a must. CEV is higher in car cost than diesel car, and for the spread/promotion, it is necessary to prepare for assistance such as subsidy. Moreover, there are many requests for improvement in number, business hours, supply capacity, etc. of fuel supply station. (NEDO)

  9. Survey report of FY 1997 on the feasibility of microbial biotechnology for reuse of environmental pollutants; 1997 nendo chosa hokokusho (kankyo osen busshitsu no shigenka no tame no biseibutsu bio technology no riyo kanosei chi kansuru chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    An investigation was conducted with the aim of elucidating the foundations for effective utilization of environmental pollutants or unused resources which are likely to be causal substances of environmental pollutants, as resources, using biotechnology. Composting of agricultural waste, production of microbial mycelium proteins and microbial fermentation materials were suggested as main examples of effective utilization of unused resources by microorganisms. Selection of active microorganisms in the livestock waste, clarification of the mechanism of action and the establishment of treatment conditions are essential to new developments in this field. In the field of marine products industry, it was pointed out that the recycling of waste using microorganisms and enzyme treatment is the most promising approach to the effective utilization of resources. In the field of food industry, applications as the culture media for mushrooms, for enzyme production and for the production of physiologically active materials as well as fuel were clarified. Was also pointed out the significance of studies on the microorganisms and enzymes in resources containing cellulose, hemicellulose and lignin, and the waste from these resources, lignocellulose. Were also proposed the composting of household waste, methane fermentation, and fermentative production of organic acid and hydrogen from waste. Possibility and significance of fermentative production of organic acid from sewage sludge were suggested. 314 refs., 46 figs., 33 tabs.

  10. Research report for fiscal 1998. Research for 'New Earth 21' project implementation program preparation; 1998 nendo chosa hokokusho. 'Chikyu saisei keikaku' no jisshi keikaku sakusei ni kansuru chosa jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the establishment of a CO2 measures introduction scenario which the world would accept, the latest information was collected, the DNE21 (Dynamic New Earth 21) model was improved, and simulation was reviewed. In fiscal 1998, simulation was performed for each district using an LDNE21 (Linear Dynamic New Earth 21) model, and an energy flow chart, energy balance table, and trade table were prepared and subjected to detailed deliberation. Studied were also conducted about the changes to occur in methanol production when the natural gas reserves and plant cost data were given different values. In the DNE21 model, the 'macro economy model' and 'warming damage function' were integrated, and simulation was performed for verification. Using a standard model compatible with COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change), comparison was made between a case in which different CO2 emission constraints were imposed on the advanced area and developing area separately and a case in which one and the same constraint was imposed on the world as a whole, and calculations were made about CDM (Clean Development Mechanism). (NEDO)

  11. FY 1997 report on the survey of potential impacts of enlarging ASEAN on political and economic systems in South East Asia; 1997 nendo chosa hokokusho (ASEAN kakudai no Higashi Asia no seiji keizai chitsujo eno eikyo chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This report surveys potential impacts of ASEAN (Association of South East Asian Nations) on inter-ASEAN affairs and its external relations when ASEAN will enlarge its members to include all nations in South East Asia, and thus fully represent the region. For this purpose, the survey was conducted on Vietnam, Myanmar, Laos and Cambodia, which joined in 1995, from the viewpoint of their economic and political system, and their relations with other member countries. The nature of ASEAN has gradually transformed, in which all the countries in the region have increased and internal economic issues have been tackled. It has an aim to stimulate inter-ASEAN trade and induce foreign direct investment into ASEAN as a whole by reducing import duties on intra-ASEAN trade. Underlying in these, new development is a concern about growing economic and military power of China. ASEAN solidarity will work an leverage against China should change toward worse, and ASEAN will function as a regional stabilization factor. ASEAN is needed for the stability of both in economic and political order in East Asia. Japan has to further promote its cooperation with ASEAN to help its solidarity as an association. 24 refs., 21 figs., 25 tabs.

  12. Report on the FY 1986 potential survey of overseas coal development. Survey of coal fields in India and Thailand; 1986 nendo kaigaitan kaihatsu kanosei chosa hokokusho. Indo oyobi Tai kau tanden chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-03-01

    The paper surveyed the coal situation and energy situation in India and Thailand. The Indian coal is bad in quality. The subject is how to drill and treat the coal with such quality in future in accordance with changes in demand for coals as a coking material and as materials for the chemical industry. For it, it is a must to make studies for coal quality, reforming technology, and utilization method. It is also necessary to reinforce transportation facilities for carrying coal to places for consumption. However, even it is the technology introduction or the geological survey, the Indian people won't accept it unless they are convinced of it. On the contrary, engineers of Thailand have a methodical side, but on the other hand they have considerable flexibility. They accept the technology and maintenance introduced as they are. Concerning how to use it, they have strength which is more than that in the country which transferred technology. In Thailand, there are various kinds of rich energy resources, and therefore, it is thought that their ignite policy will be changed. More increase in ignite production depends upon how much the consumption of energy except electric power will increase. (NEDO)

  13. Report for fiscal 1980 on comprehensive survey for nationwide geothermal resources. Survey on Curie point method (Associated material - operation flight report); 1980 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Curie tenho chosa (futai shiryo sagyo shinchoku hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-10-01

    With an objective to identify the status of distribution of deep underground thermal structure, aerial magnetism investigations were executed in the south Kyushu area, and data used in the Curie point method were collected. This paper summarizes the progresses and achievements of the work during the investigation. The report for April 1981 summarized preparation of equipment and materials by EG and G Geometrics Corporation, and the work schedules with the Idemitsu Geothermal Development, Petroleum Resources Development, and Naka-Nippon Airways. The report for April 22 compiled the site preparation and the test flight. The report for April 28 compiled the calibration and magnetism compensation flight. The report for May 5 compiled the implementation of the second flight , and the result of survey for 292 km in total. The report for May 10 compiled the implementation of the third to fifth flights, and the results of measurements for 584 km, 519 km and 360 km, respectively. The report for May 18 compiled the implementation of the sixth to eighth (final) flights, and the results of measurements for 513 km, 584 km and 68 km, respectively. (NEDO)

  14. Report on the FY 1993 basic survey for industrialization related to the survey of overseas geological structure (Tebulan East area, Malaysia); 1993 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa (Malaysia Tebulan higashi chiku) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The survey was conducted based on 'Scope of work for detailed coal exploration in the Tebulan East block of the Merit Pila coal field, Sarawak, Malaysia' concluded on June 19, 1993 between NEDO and Global Mineral which owns the mining right. The field survey was for the geological survey, survey of conditions of open pit mining, and infrastructure survey. The confirmed/estimated coal amount totaled 22,65 million tons in 4 coal seams. The all sulfur content is low, approximately 0.12%. The heating value is 5,820 kcal/kg. As to the infrastructure, various conditions are good for transportation, shipping facilities, etc. from mine site to truck transport/barge transport/external route shipping. The drilling was planned to be made by open pit mining by the truck and shovel system, and the scale of the planned production was 0.3 million tons. The ash is low in amount, and there was no coal preparation. Clean coal is produced by crushing, sieving and washing. Attached were the borehole log (JN9940782), route map, and trench sketch (JN9940783). (NEDO)

  15. Fiscal 1998 research report. Survey on the current trend of private R and D efforts; 1998 nendo chosa hokokusho. Minkan no kenkyu kaihatsu doko no jittai ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For promotion of the R and D system of technologies creating new industries, this survey collected the basic data and information on the trend of private R and D efforts and industries, and arranged every data and information obtained. The data on United States, Germany, France and U.K. in addition to Japan were collected. Survey was made first on the administrative support system for private R and D efforts. The R and D-related budget, R and D support program and private R and D-related fund of Japan, United States and U.K. are mainly outlined. Survey was made next on private R and D activities. The R and D-related fund, researcher and patent of main countries are outlined in international comparison. Survey was also made on the current state of various industries. The industry scale and structure of every Japanese manufacturing industry are outlined. Finally, the industrial statistics are given concerning Japanese 'chemical industry,' 'communication-electronics-electric measuring instrument industry' and 'automobile industry' with a high rate of R and D-related expenditures. (NEDO)

  16. Investigations in fiscal 1986 on promotion of geothermal development. Part 2. Report on precision structural test well drilling and investigation works in Otaki area; 1986 nendo chinetsu kaihatsu sokushin chosa hokokusho. 2. Otaki chiiki seimitsu kozo shisui oyobi chosa koji

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-09-01

    With an objective of promotion of geothermal development in the Otaki area in Nagano Prefecture, precision structural test well drilling and investigation works have been carried out, and the result thereof reported. The investigated area is an inclined land with an area of 70 km{sup 2} at altitudes of 1,000 to 2,000 m in the southern foot of the Mitake volcano having Otaki River as the southern border. The investigation has performed during the period from March 2 to September 30, 1987 the drilling of the N61-OT-5 test well hole (depth of 502.0 m), temperature logging, temperature restoration test, water injection test, and core test. The result of the investigation may be summarized as follows: existence of the stratigraphic succession as predicted by ground surface investigation, and existence of the Mesozoic and Palaeozoic strata of the Mino belt were verified; the Mesozoic and Palaeozoic strata of the Mino belt being the base bed have only small cracks, and very little alteration can be identified; X-ray diffraction of powder from test drilled cores recognized very little minerals altered by hot water; and the temperature logging and temperature restoration test identified no temperature indication that clearly indicates existence of heat sources. As a conclusion, there is no alteration due to hot water down to 500 m below the surface in the vicinity of the investigation well, and the possibility of a geothermal reservoir to exist is extremely low. (NEDO)

  17. FY 1997 report on the investigation on the actual status of international research information exchange in research organizations in Japan and U.S.A; 1997 nendo chosa hokokusho (Nichibei kenkyu kikan ni okeru kokusai kenkyu koryu jittai chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    An investigation was made on the actual status of utilizing researchers from foreign countries and internationally exchanging researchers with views on technological researchers in universities and public institutes in Japan and the U.S.A. Foreign researchers at 39 research institutes in the Tsukuba area are from Asian region at 43%, and European and North American regions at 43%. Asian researchers are dominated overwhelmingly by Chinese and Korean people. Researchers from Europe and North America have a high ratio of working at institutes belonging to the Ministry of International Trade and Industry, and many of them are of short period staying type. On the other hand, many of those from African regions intend to study diplomatic and cultural exchange, and those from Middle and South American regions to study agricultural and fishery industries. About 8.4% of the scientists and engineers who obtained doctorates in America in 1995 is foreign nationals, and about 83.3% of them is of long period staying type. Foreign students in the U.S.A. account for 3.1% of students in institutions of higher education. The higher the education level, the higher the foreign student ratio, whereas the ratio reaches 33.0% in doctoral courses. Persons who obtained doctorates in the department of science and engineering are, in decreasing order, Chinese, Taiwanese, Indian and Korean. 32 figs., 47 tabs.

  18. FY 2000 report on the investigation of environmental effects in the geothermal development promotion survey. Tertiary. No.B-7 Kuwanosawa area; 2000 nendo chinetsu kaihatsu sokushin chosa. Kankyo eikyo chosa hokokusho - No. B-7 Kuwanosawa chiiki (Dai 3 ji)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-01-01

    In the Kuwanosawa area, Yuzawa city, Akita prefecture, survey was conducted to grasp effects of drilling for structural boring in the geothermal survey on the peripheral environment. In the survey of animals, there were 5 orders/10 families/19 species of mammals and 10 orders/25 families/73 species of birds. Three kinds of precious animals were confirmed. There were 132 families/6,670 species in the flora. Three kinds of precious plants and three kinds of precious floras were confirmed. During the survey, drilling for structural boring was conducted. At three spas for survey, there were recognized some survey items of which there were great fluctuations. However, those are seasonal valuations or valuations related to the situation of the inside of hot springs. It is not recognized that the fluctuations were caused by the drilling work and pumping-up of geothermal water. The noise made during the well drilling was reduced around the well as theoretical values indicated. At a spot 200m away from the well, the noise was reduced from the environmental standard, and accordingly, it seems that there are few effects on the peripheral environment. The vibration was reduced around the well more than theoretical values indicated. That was below the control level at a spot 25m away from the well, and it seems that there are few effects on the peripheral environment. (NEDO)

  19. Report on survey of international cooperation possibility on chemical CO2 fixation and utilization technology in FY 1997; 1997 nendo chosa hokokusho (kagakuteki CO2 koteika yuko riyo gijutsu ni kakawaru kokusai kyoryoku kanosei chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This survey focused on the end of the more promising companion and promoting the international cooperation on chemical CO2 fixation and utilization technology. As a result, the way of the carrying-forward of the international cooperation with more than one companion could be arranged beforehand. It led to getting an arrangement about a secrecy agreement respectively with Lurgi company and ABB company in Europe, and to providing a catalyst sample developed by RITE to implement an examination by the other party and to show related technical information. In addition, it concluded a cooperation agreement about a total system of the chemical CO2 fixation and utilization technology and methanol synthesis with ZSW. In Australia, negotiation about international cooperation with CSIRO which is a federal research organization and CRC (Cooperative Research Centre) for renewable energy has been started. The ideal circumstances are being ready for the chemical CO2 fixation project for which the international cooperation with the country where the natural energy is rich like Australia is essential when coming to practical use. To do alternating current with further high density in the following year it is desired to build a concrete study cooperation system. 1 fig., 4 tabs.

  20. Confirmation study of the effectiveness of prospect techniques for geothermal resources. Deep-seated geothermal resources survey report (Fiscal year 1994); 1994 nendo chinetsu tansa gijutsu nado kensho chosa. Shinbu chinetsu shigen chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Drilling and survey of deep geothermal exploration wells were conducted to grasp the existing situation of deep geothermal resource and the whole image of geothermal systems in the area where geothermal resource was already developed. In the drilling work in fiscal 1994, 4000m-class rigs and the top drive system were planned to be used for drilling of 12-1/4 inch wells, but 9-5/8 inch liners were used for drilling down to depths of 2550m or deeper since the amount of lost circulation is large and the withdrawal of devices may be very difficult. And in 8-1/2 inch wells, the well was drilled down to a depth of 2950m. As to the deep resistivity exploration technology using electromagnetic method, studies were made of a multiple-frequency array induction logging (MAIL) method, a vertical electromagnetic profiling (VEMP) method, a joint analysis method, etc. Concerning the synthetic fluid inclusion logging technology, containers were lowered into the well and a comparison was made between data of the homogenization temperature analysis of the formed fluid inclusion and those of the temperature log analysis. With relation to the making of deep geothermal structural models, revision was made according to the determination of depths of Miocene formations, Pre-tertiary formations, and the Kakkonda granite. 65 refs., 268 figs., 79 tabs.

  1. Fiscal 1997 report on the survey of biological CO2 fixation using arid land and oligotrophic waters; 1997 nendo chosa hokokusho (kansochi, hin`eiyo kaiiki wo riyoshita seibutsuteki CO2 kotei ni kansuru chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This survey is aimed to investigate various measures to be taken for biological CO2 fixation, to synthetically study feasibilities of the measures from various aspects of CO2 fixation mechanism, scale, speed, and environmental effects and technical problems in case of introducing those, and to assess the measures quantitatively. In this fiscal year, a study was proceeded with of possibilities of carbon fixation by afforestation and that by fertilization into ocean. The paper defined significance of afforestation in arid land, and especially advantages in conducting researches in West Australia. Relationships were examined among afforestation, precipitation and topography. The result of the survey was described of water- and salt-transfer simulation methods. Studies of arid land were made in terms of photosynthetic speed, transpiration speed, soil characteristics, measuring methods for precipitation and vaporization amount, and the examples. Seven places of Leonora where water source and water quality were examined were selected, and the measuring results were described. The paper summed up the state of utilization of biomass energy obtained from forest and commented on a scenario on tree-planting. Finally, a possibility was stated of the carbon fixation by fermentation into ocean. 178 refs., 121 figs., 53 tabs.

  2. FY 1998 geothermal development promotion survey. Report on the environmental effect survey (No. A-4 Kunbetsu-dake area); 1998 nendo chinetsu kaihatsu sokushin chosa. Kankyo eikyo chosa hokokusho (No.A-4 Kunbetsudake chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-30

    Of the FY 1998 geothermal development promotion survey, the primary environmental effect survey in the Kunbetsu-dake area was conducted, and the results were arranged. In the well drilling survey, etc., the survey was made aiming at extracting areas to be preserved from an environmental aspect. The results of the survey were summarized as follows: As to the mammalia, 12 families 46 species were confirmed in the area surveyed and the periphery by literature survey. Out of them, the noticeable species which are considered important from an academic viewpoint are 10 families 19 species. As to the aves, 55 families 340 species were confirmed, of which 29 families 79 species are noticeable species. About the amphibia/reptilia, 3 families 3 species in the amphibia and 4 families 6 species in the reptilia were confirmed by literature and hearing survey. The noticeable species is 1 family 1 species in the amphilia. Concerning the terrestrial insecta, 135 families 873 species were confirmed, and the noticeable species is 11 families 20 species. As to the flora, 115 families 1055 species were confirmed, and the noticeable species is 46 families 126 species. Relating to the living vegetation, the one higher than 9 in nature reserves shows a substantial rate, and the periphery of Kaibetsu-dake is designated as the specified flora colony. (NEDO)

  3. FY 1992 report on the survey of geothermal development promotion. Electromagnetic exploration (TDEM method) (No. A-1 - Haneyama area); 1992 nendo chinetsu kaihatsu sokushin chosa chijo chosa hokokusho futai shiryo. Denji tansa (TDEM ho) hokokusho (No. A-1 Haneyama chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    For the purpose of elucidating a possibility of existence of geothermal reservoirs in the Haneyama area, Oita Prefecture, Electromagnetic survey by the TDEM method was conducted. The survey was made for the area of 80km{sup 2} at 105 measuring points in the south of the Haneyama area, and the resistivity structure reaching the depth of 4,000m from the earth surface was made clear. The resistivity structure in this area is composed of 4 layers: upper medium resistivity layer, central medium resistivity layer, central low resistivity layer and lower high resistivity layer. The resistivity structure discontinuous line ranges between the uplift zone of basement and the sedimentation zone, and the greater part of the alteration zone is distributed and arranged concomitant with the position and direction of the line. As the region with high potential of geothermal existence, cited were the low resistivity zone distributed in the west of the resistivity structure discontinuous line that continues from Mt. Fukuman to the south, the low resistivity zone distributed in the north of the resistivity structure discontinuous line from Noya to the west, and the low resistivity zone distributed in the north of Hosenji and lying between resistivity structure discontinuous lines. (NEDO)

  4. Researches regarding a constructing problem of a PV system. Part 1. Conscious investigation by means of a questionnaire survey; Taiyoko hatsuden system ni okeru kenchikuteki shomondai no kenkyu. 1. Anketo chosa ni yoru ishiki chosa

    Energy Technology Data Exchange (ETDEWEB)

    Nakajima, Y; Yamazaki, R; Kuroki, T [Kogakuin University, Tokyo (Japan)

    1996-10-27

    The installation and introduction of photovoltaic power generation systems (PVS) in buildings are growingly expected in the construction field from now, coupled with the marketing of a solar cell module as a product for a construction material in the form of an external wall or a roof material for example. For this purpose, it is necessary at first to summarize problems that may arise at the time of or after the installation of PVS as a product. This paper examines an opinion poll, degree of recognition, current problems, etc., of PVS as a result of a questionnaire survey given to engineers and architects engaged in the actual construction business. The degree of recognition and interest was very high. Consultation or request for PVS installation was much more than predicted in numbers. Roughly 50% of the respondents reacted positively for the future installation request of PVS and, combined with the respondents who answered to look into the installation tentatively, not less than 90% were of a forward-looking opinion. The 85% of the respondents was not aware of the monitor business system for residential PVS. Further, the survey clearly brought out the importance of cost problems. 1 ref., 11 figs., 3 tabs.

  5. FY 1998 annual report on the survey and research on methodology for estimating reduced amounts of greenhouse effect gas emissions; Onshitsu koka gas haishutsu sakugenryo santei hoho ni kansuru chosa kenkyu 1998 nendo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Although introduction of Joint Implementation (JI) and Clean Development Mechanism (CDM) have been adopted in the COP3, the details of how to set up the baseline for calculating the emission reduction amounts have not been established. This survey/research project has sorted out various concept menus for setting the baseline, verify each menu, and positively propose the methodology in an international arena, in which merits and demerits involved in simplified approaches, which try to simplify the works for setting the baseline, are analyzed, and their effectiveness is investigated. At the same time, both FCCC AIJ and NEDO AIJ projects are analyzed, to understand characteristics of baseline-setting method adopted by each project. There are many project types, to which direct application of any simplified approach is difficult. It is therefore realistic to analyze the situations case by case for the time being, and pursue for possibility of standardization of the baseline-setting methods after sufficient experience and data are accumulated to allow classification of the projects by common features. (NEDO)

  6. Fiscal 1996 verification and survey of geothermal prospecting technology etc. 2/2. Survey report on deep-seated geothermal resources; 1996 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 2/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of reducing the risk to accompany the exploitation of deep-seated geothermal resources, investigations are conducted into the three factors that govern the formation of geothermal resources at deep levels, that is, the supply of heat from heat sources, the supply of geothermal fluids, and the development of fracture systems contributing to the constitution of reservoir structures. In the study of deep-seated geothermal models for the Kakkonda area, a reservoir structure model, a thermal structure model, and a geothermal fluid/hydraulic structure model are deliberated. Then, after studying the relations of the said three structure models to fracture systems, the boundary between the geothermal fluid convection region and the thermal conduction region near the 3,100m-deep level, the existence of high-salinity fluids and the depth of gas inflow, the ranges of shallow-seated reservoirs and deep-seated reservoirs, the trend of reduction in reservoir pressure and the anisotropy in water permeability in shallow-seated reservoirs, etc., a latest reservoir model is constructed into which all the findings obtained so far are incorporated. As for guidelines for deep-seated thermal resources survey and development, it is so decided that deep-seated geothermal survey guidelines, deep-seated fluid production guidelines, and deep-seated well drilling guidelines be prepared and that assessment be made of their economic effectiveness. (NEDO)

  7. Survey on acceleration of geothermal development in fiscal 1998. Report on survey for influence on environment (No. B-7, Kuwanosawa district); 1998 nendo chinetsu kaihatsu sokushin chosa.Kankyo eikyo chosa hokokusho (No. B-7 Kuwanosawa chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    A survey was performed on the current situation in the Kuwanosawa district in Akita Prefecture to identify influence on the surrounding environment due to drilling of geothermal structure testing wells. The survey on animals covered mammals of five divisions, 10 families and 19 species, Aves of ten divisions, 25 families and 73 species, reptiles of one division, 3 families and 6 species, Amphibia of two divisions, 6 families, 9 species, and Insects of 17 divisions, 179 families and 719 species. Precious animals of a several species including black salamander were identified. In the plant survey, 132 families and 670 species were identified, with several species listed as the precious plants. In the survey of hot springs, those at three locations were all high-temperature hot springs at as high as 53.8 to 96.9 degrees C. Amount of discharge, pH and electrical conductivity differ largely by the hot springs. The hot spring in Takamatsu did not show large variation throughout the survey period. The Ogura Inn at Doroyu Spa has small variation in pH and hot spring temperature, but large variation in the amount of discharge and Al{sup 3+} concentration. Correlation was recognized between hot spring temperature and amount of discharge, between hot spring temperature and anion, between amount of discharge and electric conductivity, and between amount of discharge and anion. (NEDO)

  8. FY 1999 report on the geothermal development promotion survey - Akinomiya area survey. Temperature/pressure logging before the long-term jetting test; 1999 nendo chinetsu kaihatsu sokushin chosa Akinomiya chiiki chosa hokokusho. Choki funshutsu shikenmae no ondo atsuryoku kenso

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-06-01

    As a part of the FY 1999 geothermal development promotion survey - Akinomiya area survey, the rising speed/vertical permeability of the fluid associated with the natural flow were calculated by grasping the temperature of geologic layers/reservoir pressure in the survey area and the temperature distribution for vertical depth. In the survey of boreholes in the Akinomiya area: N9-AY-3, N10-AY-6, N10-AY-7, N10-AY-8, temperature/pressure logging was conducted in the stationary state at the time when a lot of time passed after drilling, water-filling test and jetting test having been finished. In the temperature/pressure logging, the continued measurement was made using PTS logging device to simultaneously measure temperature/pressure/impeller revolution number and lowering measuring device. As a result of the survey, it was assumed that there is a possibility of occurrence of the borehole fluid flow around the depth of 980-1290m and 1320-1540m of N9-AY-3 and around the depth of 880-1090m of N10-AY-8. The rising speed and permeability of fluid from each well indicated the same order at three wells. (NEDO)

  9. Fiscal 1997 research report. International energy use rationalization project (Analytical tool research project for energy consumption efficiency improvement in Asia); 1997 nendo kokusai energy shiyo gorika nado taisaku jigyo chosa hokokusho. Asia energy shohi koritsuka bunseki tool chosa jigyo (honpen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    Efforts have been under way to prepare inter-industry relations tables and energy data for four Asian countries, namely, China, Taiwan, Singapore and Malaysia, and a tool for energy consumption efficiency analysis has been developed and improved. In Chapter 1, energy supply and demand in the above-named four countries is reviewed on the basis of recent economic situations in these countries. In Chapter 2, bilateral inter-industry relations tables usable under the project are employed for the analysis of the economic status of each of the countries and energy transactions between them, and a method is described of converting the tables into one-nation inter-industry relations tables which meet the need of this project. In Chapter 3, national characteristics reflected on the respective energy input tables are described, and a method is shown of converting a nationally characterized unit energy table into a common unit energy input table for registration with a database. In Chapter 4, the constitution of the Asian energy consumption efficiency improvement analyzing tool and a system using the tool are explained. In Chapter 5, some examples of analyses conducted by use of the analyzing tool are shown, in which the energy saving effect and CO2 emission reduction effect are estimated for Indonesia by use of the analyzing tool. (NEDO)

  10. Report for fiscal 1999 on the fundamental survey on promotion of joint implementation. Modernization of Bakabad Cement Factory; 1999 nendo kyodo jisshi nado suishin kiso chosa Bekbad cement kojo kindaika chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes the result in fiscal 1999 of the feasibility study applied with the COP3 clean development mechanism for Bekabad Cement Factory in the Republic of Uzbekistan. One of the existing three old type kilns were diverted and converted into a dry NSP type kiln (having the same production capacity as the present of 726,000 tons a year). This arrangement was intended to enhance the productivity, save the energy, and reduce emission of greenhouse gases and different pollutants by renewing the upper and lower stream facilities and installing such environmental devices as electric dust collectors and bag filters. The total construction cost is US$84,432,000. Reducible energy consumption and reduction quantity of greenhouse gases would be 73,232 toe/year and 176,528 toe/year, respectively, in the single fiscal 2006. The cumulative quantity over twenty-year period until 2025 would be 1,464,640 toe and 3,530,560 toe, respectively. The energy saving effect per US$1,000 would be 17.87 toe, and the greenhouse gas reduction effect would be 43.08 t. In the case of using a soft loan such as the special yen loan for environment application, the internal profit rate after tax would be 7.63%, which is not high as the business enterprise profitability. However, the profit and loss statement indicates creation of profit after two years of operation, hence there is a relative realization possibility. (NEDO)

  11. Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Survey by region/industry in India; Kankyo chowagata sekitan riyo system kanosei chosa. Indo ni okeru sekitan riyo gaikyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A survey was made in India which is a coal producing/consuming country following China in Asia and where coal is used for about 60% of the primary commercial energy. The survey was conducted on coal production/distribution/utilization and environmental issues, aiming at studying feasibility of introducing the environmentally friendly coal utilization system into every industry including the residential/commercial one, and at implementing a comprehensive master plan including Japan`s international cooperation. Total power source facilities in fiscal 1995 are 83.3 million kW, 64% of which are coal thermal power facilities and generated 260 TWh, 69% of the total output energy. Main commercial energy sources are coal, oil and natural gas, and oil is self-sufficient. The survey this time did not examine very well the actual state of the environmental pollution problem caused by the coal utilization. Indian coal is high in ash content but low in sulfur content, and therefore, SOx polluting air has not been a very important problem so far, but soot/smoke is almost the problem. Further, ash treatment after combustion at boilers, etc. is expected to be a big problem in the future. 49 figs., 88 tabs.

  12. FY 2000 report on the investigational study of the general PR method for spreading clean energy vehicles and letting people know them; 2000 nendo chosa hokokusho. Clean energy jidosha fukyu keihatsu no tameno ippan koho shuho ni kansuru kento chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The details were outlined of the PR event 'Clean Energy Festa' which was carried out for PR activities for spread of new energy and clean energy vehicles. The festa was implemented in Yokote (Akita prefecture), Nagoya, Osaka, Yokohama and Hiroshima. The details of each place were reported in terms of the following: outline of the implementation, map of the place and booths, opening ceremony, management at entrance, dome theater, place for enjoying/relaxing, festival plaza, parking lot, PR related works, etc. In Festa in Yokote, more people gathered than expected. The reasons seem to be: the festa was held in the existing amusement facilities; the show using costumes of popular characters and gifts of the lottery were effective. As to new energy and clean energy vehicles, appeal was made mainly by stamp rally and questionnaire survey. By moving people inside the place, it helped people to have an understanding of clean energy vehicles. Almost the same effects were recognized also in the other places. (NEDO)

  13. Feasibility survey of the environmentally-friendly coal utilization system. Feasibility survey of the environmentally-friendly coal utilization system in Indonesia; Kankyo chowagata sekitan riyo system kanosei chosa. Indonesia ni okeru kankyo chowagata sekitan riyo system kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    With relation to the coal of Indonesia, where the expansion of the use of coal as a substitute for petroleum/plant fuel is aimed at, the paper grasped the situation of coal production/distribution/utilization and environmental problems, and analyzed the situation of the coal utilization/spread by industry including the commercial/residential use. The purpose of the survey is to work out a comprehensive master plan including Japan`s international cooperation for introducing the environmentally-friendly coal utilization system to Indonesia. Coal utilization systems, the introduction of which Indonesia should study in future, were picked up, according to the surveys in fiscal 1993 and 1994. In commercial/residential and small-scale industry sectors, needed is improvement of carbonization technology for production of coal carbonization briquette. Moreover, the introduction of bio-briquette should be studied in the future. In the power generation sector, studies should be made on the introduction of technology for SOx/NOx reduction and technology for coal ash treatment including the effective use of coal ash. For the introduction of coal boilers, the combustion mixed with bagasse, which is abundant in amount, is also necessary. In the coal production sector, coal preparation technology is studied, and a method to select the optimum process was proposed through the simulation. 76 figs., 43 tabs.

  14. Research report of fiscal 1997. Survey on creation of high-efficiency renewable resources, and bioconversion technology; 1997 nendo chosa hokokusho. Kokoritsu saisei kano shigen no sosei narabi ni bioconversion gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Survey was made on material production technology using creation technology of high-efficiency renewable resources (photosynthesis reaction of plants). Industrially usable plant resources in overseas countries and Japan were arranged, and plant resources unused for food were also surveyed. The present state of genetic engineering necessary for metabolic engineering of higher plants such as fit and high-expression technology of genes, plant cell cultivation, and control technology of plant cell multiplication is described, and elementary technologies required for future gene-recombined plants are predicted. Survey was also made on the trend of creation technology of industrial plants for fat and oil, biodegradable polyester, amino acid, cellulose, fiber (cotton) and forest wood. A patent list on plant biotechnology was prepared, and study on bioconversion of plant resources was also surveyed. Overseas R & D trends on conversion and effective use technologies of renewable bio- resources are reported, and process design and its profitability were evaluated through a case study. 414 refs., 87 figs., 55 tabs.

  15. Research report for fiscal 1998 on the analysis of spread effect of technologies approved as international standards. Value web analysis and research; 1998 nendo kokusai hyojun ni ninteisareta gijutsu no hakyu koka bunseki chosa hokokusho. Value wave bunseki chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For contributing to the formulation of technology development programs, an analysis is conducted based on the concept of value web into which the economic spread effect is incorporated. As information technology plays an important role in the fields of automobiles and chemical materials, there are various fields the research and development efforts exerted in which are common to many others. As to what additional values are created when such separately developed technologies cross each other, a discussion is conducted using techniques of industry-oriented analyses. Findings obtained are mentioned below. When the numbers of essays relative to the respective industries are compared, it is found that 63% of the total number of biotechnological essays fall on agriculture, the drug industry, and the food industry. On the other hand, when it comes to the produce, related industries larger in marketing scale is more strongly influenced by the spread effect. The spread effect of biotechnology is distinguished in the drug industry, and that of information/communication technology in the information industry, electric and electronic industries, and in the semiconductor industry. (NEDO)

  16. Fiscal 1992 research report. Research trend survey of research and development of advanced materials for extreme environments (Carbon composite material); 1992 nendo chotaikankyosei senshin zairyo no kenkyu kaihatsu chosa hokokusho. Tansokei fukugo zairyo ni kakawaru kenkyu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    Trends of research on carbon based composite materials were surveyed through studying various reports and technical literature and evaluation of the project named above was conducted through holding interviews with researchers. In the survey of research trends for which technical literature perusal was the main tool, it was found that in most technical articles the important task was the enhancement of oxidation resistance, that SiC coating was in use for this purpose, that the technology would meet its limit at 1,600-1,700 degrees C, and that it would turn useless at temperatures beyond 1,800 degrees C. For the evaluation of the project, interviews were held with nine researchers not taking part in the project. The researchers favored the project as far as the popularity of the project and the main implementing body and system were concerned, but they negatively evaluated the project's goal of using such materials at 2,000 degrees C in the atmosphere. This research report comprises four chapters which cover (1) trends of research on C/C (carbon/carbon) composites, (2) a summarized research report on C/C composites, (3) survey of patents associated with C/C composites, and (4) opinions expressed toward the project and the results of evaluation conducted on the same. (NEDO)

  17. Research report for fiscal 1998. Survey on the researchers and research institutes for the effects of global warming and its countermeasures; 1998 nendo onshitsu koka gas ni yoru kankyo eikyo nado ni kansuru kenkyusha kenkyu kikan chosa chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Researchers and research institutes across the world (except those in Japan), engaged in the study of global warming and measures to deal with the phenomenon, are extracted in compliance with certain specified standards, and the latest information on them is appropriately arranged and listed. It is further developed into an electronic database for the convenience of users. The collected information includes more than 230 research institutes and more than 1,000 researchers. The endeavor is exerted by extracting essays and institutes mainly out of the on-line databases. More than 1,000 essays and 130 institutes are covered. Visits are made to five institutes in the U.S. and four in Europe who are most actively engaged in the study of global warming, and detailed researches are conducted and information is exchanged. The Argonne National Institute copes with all energy problems related to global warming. Descriptions are given about environmental impact surveys and CO2 isolation in the ocean at the Center for Global Science of the Massachusetts Institute of Technology. At the Oak Ridge National Laboratory, the visitors heard explanations of technologies related to renewable energies and so forth. Researches are made into ecosystems at the University of California, and into natural energies at the University of Hawaii. Also visited are research institutes in Australia, Germany, Netherlands, and Britain. (NEDO)

  18. Achievement report on research and development in the Sunshine Project in fiscal 1977. Surveys and studies on patents and information (Surveys on patent information); 1977 nendo tokkyo joho chosa kenkyu seika hokokusho. Tokkyo joho chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-03-01

    This paper describes achievements in fiscal 1977 of patent information surveys on hydrogen technologies. Japan is most enthusiastic in developing the thermo-chemical hydrogen manufacturing method. While no noticeable patents were found on the electrolytic method, researches on membranes and electrodes are expected. With regard safety assurance, it is necessary to establish safety assuring technologies suitable for each stage of hydrogen manufacture according the flow of manufacturing, liquefaction, storage, transportation and utilization of hydrogen. Development of mechanisms to prevent hydrogen embrittlement and destruction (leakage) is especially demanded. Enhancement of economic performance and reliability of hydrogen fuel cells requires research and development in the whole fuel cell configuration and also in the fields of auxiliary devices, in addition to that for catalysts and electrodes. Few patents are applied for in solid electrolyte and molten salt fuel cells. The most noticeable problems in hydrogen combustion devices are prevention of reverse ignition, safety measures for colorless flame, and positive utilization of hydrogen combustion characteristics in mixed combustion. Inventions tackling squarely with these problems can hardly be found. It was difficult to discover contributive and effective technologies because the hydrogen combustion characteristics are widely different from those of other fuels. (NEDO)

  19. Report for fiscal 1981 on comprehensive survey for nationwide geothermal resources. Survey on radar imaging method - geothermal analysis conception design (Appendix); 1981 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Radar eizoho chosa (chinetsu kaiseki gainen sekkei furoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-10-01

    This paper explains different theoretical calculation methods used in gravity and magnetic force data analysis in geothermal resources survey. Analyzing the gravity data and the magnetic force data is capable of being applied with the potential theory. The increased speed and capacity of recent computers make easier the conversion of data into wave number zone. In relation with heavy magnetic force analysis, the paper explains such items as basic handling, IGRF remainder calculation, methods for topographic correction, conversion of primary and secondary polar magnetism and conversion of pseudo-gravity, coherent analysis, spectral ratio method, estimation of spectra by using MEM, spectrum moment method, heavy magnetic force simultaneously analyzing type modeling, constraint inversion method, and other methods. The paper further explains the sequential approximation method in magnetization calculation, methods for calculating equivalent magnetization distribution (methods by Bhattacharyya and Chan, and Nakatsuka), method for calculating equivalent magnetization distribution (method by O'Brien), primary and secondary polar magnetism conversion relation formulas, and theoretical calculation of spectral ratio. (NEDO)

  20. Research report for fiscal 1998. Research for 'New Earth 21' project implementation program preparation; 1998 nendo chosa hokokusho. 'Chikyu saisei keikaku' no jisshi keikaku sakusei ni kansuru chosa jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the establishment of a CO2 measures introduction scenario which the world would accept, the latest information was collected, the DNE21 (Dynamic New Earth 21) model was improved, and simulation was reviewed. In fiscal 1998, simulation was performed for each district using an LDNE21 (Linear Dynamic New Earth 21) model, and an energy flow chart, energy balance table, and trade table were prepared and subjected to detailed deliberation. Studied were also conducted about the changes to occur in methanol production when the natural gas reserves and plant cost data were given different values. In the DNE21 model, the 'macro economy model' and 'warming damage function' were integrated, and simulation was performed for verification. Using a standard model compatible with COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change), comparison was made between a case in which different CO2 emission constraints were imposed on the advanced area and developing area separately and a case in which one and the same constraint was imposed on the world as a whole, and calculations were made about CDM (Clean Development Mechanism). (NEDO)

  1. FY 2000 report on the basic survey to promote Joint Implementation, etc. Survey of gas-fired cogeneration in Samarkand City; 2000 nendo kyodo jisshii nado suishin kiso chosa hokokusho. Samarkand shi gas daki cogeneration chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In the existing heat supply plant in Samarkand City in Uzbekistan, feasibility study was conducted of the project aimed at energy conservation and reduction in greenhouse effect gas emission by introducing the repair/cogeneration system of the regional pipes superannuated. In the project, the following were planned: introduction of two units of 6MW class gas turbine cogeneration, introduction of boiler which can realize 90% of the thermal efficiency, replacement of the existing regional pipes with pre-insulated pipes with less water leak/heat loss, etc. As a result of the study, the energy conservation amount was 21,006 toe, and the amount of greenhouse effect gas reduction was 64,998 t-CO2/y. As to the effects vs. expenses, the energy conservation was 2.80 toe/million yen, and the greenhouse effect gas reduction was 8.66 t-CO2-y/million yen. The initial investment amount was 7.51 billion yen, the business profit was 468 million yen/y, and the internal earning rate was 1.133%. It was judged that great profitability was not expected for the project, but the profit was returnable on investment. (NEDO)

  2. Investigations in fiscal 1983 on promotion of geothermal development. Part 1. Report on investigation of fumarolic environmental effects in Oku-Aizu area; 1983 nendo chinetsu kaihatsu sokushin chosa. 1. Okuaizu chiiki funkichu kankyo eikyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-01

    As part of the investigations on promotion of geothermal development, surveys have been carried out in the Oku-Aizu area to identify the existence and/or extent of effects of collecting geothermal fluids above the ground imposed on the environment, such as the natural ecological system. The investigated area is an area of 60 km{sup 2} covering Kawanuma County and Onuma County in Fukushima Prefecture, a mountainous area with undulations. The investigation result may be summarized as follows: the area shows the inland climate and has snow fall as much as 2 m in winter; according to the H2S diffusion prediction, the concentration thereof on the land in seasonal average is 0.7 ppm at maximum, which is a value presenting no problems. No fumarolic effects of SO2 were identified, and floating dust and Hg showed values that present no problems. With regard to water quality during and after the blowout test, no effects of blowout return were identified. The noise level was 41 to 45 phones at a place 100 m distant, and the vibration level has become the lower detection limit at a place 50 m distant. Leveling has discovered no ground movement. No variation in major constituents in thermal spring water was verified before and after the blowout test. (NEDO)

  3. FY 1997 report of survey on the intellectual property in international collaboration research project; 1997 nendo chosa hokokusho (kokusai kyodo kenkyu ni okeru chiteki zaisanken ni tsuite no chosa hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In promoting international collaboration research project, coordination of the patent system of each country which participants to the project belong to has broad implications in concluding the contract for the project. For example, in Japan, 100% of the patent belongs to the government for contrast or collaboration project with the government. While, in the USA, the patent developed by the private company belongs to the private company even for the contrast project. In Japan, the shared patent can not be transferred to the third party or implemented without agreement with the partner. While, in the USA, the shared patent can be transferred to the third party or implemented without agreement with the partner. Due to such a difference, some projects can not be established by ill coordination of intellectual property even when the meaning of the projects is well understood. In this survey, was investigated the outline of patent systems of major countries to study about what should well balanced treatment of intellectual property in international collaboration research project be in the future. 4 figs., 8 tabs.

  4. Survey and research achievement report for fiscal 1980 on patent and information under Sunshine Program. Survey of information on new energy technology development (Solar energy); 1980 nendo tokkyo joho chosa kenkyu seika hokokusho. Shin energy gijutsu kaihatsu joho chosa (taiyohen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    Solar energy as defined by the United States includes hydroelectric power, biomass, and the ocean. The short-term strategy deals with passive solar air-conditioning, hydroelectric power, and biomass direct combustion. The medium-term strategy involves positive heating and wind power. The long-term strategy covers heat for agriculture, photovoltaic power, and OTEC (ocean thermal energy conversion), and the ultralong-term strategy covers power generation in space and photochemical conversion. Canada is behind other countries in the conversion of solar energy into power, and solar energy is used but passively as heat source, this because this country is rich in other resources. In West Germany, solar energy may be exploited for hot-water supply and heating at high latitudes, but it is not likely that it will be used for power generation. Home heating offers some appeal since potential demand for it is great. In Britain, the use of solar energy is not a pressing matter, this because systems for effective use of coal have long been established at homes, society, and industries in this country, rich in coal resources and enjoying oil from the North Sea oil field. France's efforts include biomass exploitation. In its development efforts, importance is attached to home heating, hot-water supply, and biomass. Next comes the conversion into power of solar energy. Photocells are also a subject of research and development. (NEDO)

  5. Fiscal 1998 research report. Feasibility study on improvement of the thermal efficiency of existing coal- fired thermal power plants in China; 1998 nendo chosa hokokusho. Chugoku kisetsu sekitan karyoku hatsudensho koritsu kojo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Feasibility study was made on the improvement project of the thermal efficiency of existing coal-fired thermal power plants in China to relate it to Japanese clean development mechanism. General study was made on the facility and operation of existing 300MW coal-fired thermal power plant units, and on-site study was also made on improvement of the thermal efficiency of some typical power plants. Based on these studies, effective improvement measures were identified, and general evaluation was carried out based on a cost effectiveness. The study result showed that the total efficiency improvement measures improve the plant efficiency of a standard 300MW unit by nearly 4%, and reduce CO{sub 2} emission by 184 ktons/y. The efficiency improvement measures for 10 300MW units by 2010 are estimated to reduce CO{sub 2} emission by 1.84 Mtons/y in 2010. This reduced emission is equivalent to annual emission of one 300MW unit. This project is reasonable enough if the cooperation range between Japan and the other country, and a source of funds are clarified. (NEDO)

  6. Fiscal 1999 geothermal energy development promotion survey. Report on survey of structural boring (No. B-7 Kuwanosawa area); 1999 nendo chinetsu kaihatsu sokushin chosa. Kozo shisui chosa koji oyobi kaiseki hokokusho (No.B-7 Kuwanosawa chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    Borehole N11-KN-1 was digged and investigated for clarifying the geothermal structure of the Kuwanosawa area, with attention fully paid to the existing survey results. The hole is inclined, 1,802.30m deep in total, with a casing pipe installed down to the 1,101.76m level. Temperature was measured and electrical logging was performed at levels 410m, 1,110m, and 1,802.23m while the hole walls were still exposed bear. The maximum temperature of 161 degrees C was observed at the hole bottom, and the product of permeability - layer thickness transmission coefficient was described by 3.72 to 4.75 times 10{sup -1} darcy.m. The geothermal structures in presence in the south-western part of the survey area and along the Wasabizawa fault were made clear, and it was found that there exists no high-temperature water system in the vicinity of borehole N11-NK-1. As tasks for the future, it was proposed that a geothermal survey of the south-eastern part which includes borehole N57-YO-2 and a geochemical survey of fluids including hot spring water and surface be conducted. (NEDO)

  7. Research report on promotion of geothermal energy exploitation for fiscal 1997. Fluid geochemical research (No.B-6 Tsujinodake district); 1997 nendo chinetsu kaihatsu sokushin chosa. Ryutai chikagaku chosa hokokusho (No.B-6 Tsujinodake chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-07-01

    The research covers the Tsujinodake district spreading over Yamakawa-cho and Ibusuki-shi, Kagoshima Prefecture. Hot spring water in the district is of the neutral Cl type, heated mainly by conduction and containing seawater. The thermal water layer of the highest geothermal potential exists in the vicinity of the Nishi district of Ibusuki-shi. It spreads widely in the westward part and may be linked with the Unagiike district. The temperature of the deep-seated thermal water layer is estimated at 220-230 degrees C, yet it may be higher. In addition to the layer in the vicinity of the Nishi and Unagiike districts, there is a shallow-seated hot spring aquifer in the Nagasakibana district, where the deep-seated thermal water is probably prevented from lifting in the presence of an aquiclude. In the Narikawa district, possibilities are low that the thermal water just beneath will come up. As for hot spring water in the Oyama and Okachogamizu districts, there are no signs of high-temperature thermal water infiltration. In these two districts, it appears that hot spring water is heated by conduction over a large area. For the disclosure of linkage of hot water systems and deep-seated geothermal structures which cannot be detected by geochemical investigations conducted into hot spring water, etc., it is necessary to resort to geological and geophysical researches, and to carry out test drilling. (NEDO)

  8. FY 2001 report on the initial-stage survey of the project for working out the new energy vision of the Okinawa City area; 2001 nendo Okinawa shi chiiki shin energy vision sakutei chosa. shoki dankai chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-02-01

    For working out a new energy vision in Okinawa City, an investigational survey was conducted, as the initial-stage survey, of the state of energy demand of the city, estimated amount of existence of new energy, proposed project (draft) on new energy introduction, etc. The energy demand amount of Okinawa City was estimated at 6,865 x 10{sup 6} MJ/y. By sector, it consisted of 41.6% in the transportation sector, 35.6% in the commercial/residential sector and 22.8% in the industrial sector. The rate of energy source was 50.5% of petroleum-base fuel, 31.0% of electric power and 9.5% of LP gas. The expected minable amount of new energy was estimated at 318,513 x 10{sup 3} MJ/y, which is equivalent to 17 x the energy consumption amount/day of the city. As the proposed project (draft) for new energy introduction, study was made of the introduction of photovoltaic power system/solar heat utilization system to the children future zone park/elementary school/junior high school/kindergarten/public hall, introduction of clean energy vehicle to official vehicle of the city, refuse incineration power generation/utilization of incineration heat at Kurahama sanitary facilities, and others. (NEDO)

  9. FY 2000 report on the geothermal development promotion survey - No.C-4 Shiro-mizukoshi area. Resource survey (Primary); 2000 nendo chinetsu kaihatsu sokushin chosa. No. C-4 Shiromizukoshi chiiki shigen chosa hokokusho (Dai 1 ji)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-01-01

    As a part of the FY 2000 geothermal development promotion survey, survey was conducted in the Shiro-mizukoshi area (about 10km{sup 2}), Kagoshima prefecture, the gradually-inclined area located at the southwest foot of Volcano Kirishima, and the results were summed up. In the survey, the following were carried out: surface survey such as geology/alteration zone/fracture system, high-density gravity exploration, electromagnetic exploration, geochemical fluid survey, core test by drilling three exploration boreholes, temperature log, temperature recovery test, water injection test, short-term jetting test, etc. N12-SZ-1 came across the reservoir associated with the ENE-WSW system fault at a depth of 1,085m. The result of the temperature log and the geochemical temperature indicated that the temperature of the reservoir was between 230 and 240 degrees C. However, the reservoir was regarded as the vapor heating reservoir heated by the high-temperature vapor which is thought to be the shallow ground water separated from the deep reservoir. N12-SZ-2 was a large lost circulation zone at a depth between 1,325 and 1,486m, which indicated that N12-SZ-2 came across the ENE-WSW system Shiro-mizukoshi fault. N12-SZ-3 seems to be the area into which ground water flows. (NEDO)

  10. Fiscal 1997 survey report on the trend of global warming protection measures of substituting freons; 1997 nendo chosa hokokusho (daitai freon no chikyu ondanka taisaku doko ni kansuru chosa hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The trend survey was conducted of global warming protection measures by participation in international conferences, scientific society meetings and lecture meetings, and by literature surveys. We participated in the international conference on ozonosphere protection measures. In the 9th meeting of the nations which concluded the Montreal Protocol, the strengthening of restrictions on methyl bromide was decided on. In the UNEP solvent technology selection conference and the OORG conference of the World Bank, reports were made on substituting solvents in Japan, activities supporting developing countries, and the developmental trend of urethane use foaming agent. In the international conference on ozonosphere protection measures, introduced were the present status of Japan`s ODA for developing countries and examples of success of the substitution in the solvent field. The paper included nine reports on CFC destruction technology related literature made public in the past one year. The paper also introduced a comparative study of de-HCFC substituting technology at U.S. Oak Ridge National Laboratory, U.S. EPA`s prediction of emission of fluorine 3 gas, the predicted value of HFC emission and trial calculation of contributing rate in all greenhouse gases by IIR, Green Peace and Elf Atochem, and NOAA`s measured data on SF6 in the atmosphere. 49 refs., 46 figs., 26 tabs.

  11. Report on the achievements in fiscal 1999. Surveys on the foundation for establishing industrial technology strategies (Foundation and environment improving strategies - an overall survey); 1999 nendo sangyo gijutsu senryaku sakutei kiban chosa hokokusho. Kiban kankyo seibi senryaku (zentai chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Surveys were performed on the foundation for technological innovation in Japan and other countries. Main findings obtained from the actual state survey were compiled from the two aspects of 'items having difference in international comparison' and 'main findings by nucleuses and functions'. In order to activate the economy stagnated in the 1980's, America has developed strong industrial technology policies under the initiative of the government to strengthen the competitive edge, and the result thereof appears linking with the briskness in the today's U.S. economy. In Japan, the non-competitive fund distributed uniformly to national universities and national research institutes accounts for the majority in the governmental research fund. In contrast, many of the research funds of the U.S. government are the competitive fund, whereas researchers perform their research works using these funds, including their own labor cost, and the competition is intense. America is regarded to have put a huge amount of national defense research expense and space development research expense into private business entities, which are playing a large role in developing advanced technologies. A great amount of governmental fund is injected concentratedly into researches of health, medical and bio-technologies. (NEDO)

  12. Report on surveys in fiscal 1999. Foundational survey for establishing strategies for industrial technology (surveys on strategies for establishing priorities and improving intellectual foundation); 1999 nendo sangyo gijutsu senryaku sakutei kiban chosa. Jutenka senryaku chiteki kiban seibi chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to promote technological developments smoothly, surveys and discussions were given on how the improvements in intellectual foundations are worked out inside and outside the country. In surveying the status of improving the databases inside and outside the country, it was disclosed that the databases both inside and outside the country are arranged under the auspices of the governments. The reason for this is considered because the intellectual foundation improvement is difficult to be established as a business. In order to structure a framework to put together and publicize the data including those possessed by the private sector, surveys and discussions were given on the interest among titles to intellectual properties, contractual relationship between the database improving parties and the data providing parties, relationship with taxation systems, and how the incentives should be provided for publicizing the data. In discussing a model case to utilize data acquired by the private sector, it was concluded that assistance by the governments is indispensable for the organizations for structuring and maintaining the databases to continue their activities independently. Among the data measured and managed at the national level, problems in the publicizing method thereof were discussed especially on the data related to ocean information. (NEDO)

  13. Fiscal 1999 geothermal energy development promotion survey. Report on survey of introduction of techniques for predicting impact on hot springs; 1999 nendo chinetsu kaihatsu sokushin chosa hokokusho. Onsen eikyo yosoku shuho donyu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-08-01

    In an effort to find guidelines on how to proceed with geothermal energy development so that it may coexist with hot springs, investigations are conducted into cases of impacts on hot springs imposed by geothermal energy development activities. An impact is judged to exist when geothermal development results in a decrease or depletion of pumped or spontaneously welling hot spring water, change in the concentration of dissolved chemical ingredients, fall in water temperature, or in an increase in the amount of discharged steam. Keyword-aided retrieval of data from databases is performed, and geothermal magazines are referred to for information. There are articles reporting impacts imposed by geothermal development on hot springs in the Palinpinon area (Philippines) and 12 others and in the Corwin Springs area (U.S.) and 13 others. These articles carrying outlines and impacts of geothermal development are collected, put in order, and analyzed. Cases in which such impacts are found to exist are categorized into four groups and, in each group, episodes are differentiated from each other by the type of mechanism linking the aquifer and the reservoir which is the object of development. (NEDO)

  14. FY1998 survey on preparation of data collection related to new energy technology development (cogeneration); 1998 nendo shin energy gijutsu kaihatsu kankei data shu sakusei chosa (cogeneration) chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    New energy technologies have had the subsidy institutions established in association with advancement of the technologies, and such introduction promoting measures developed as the introduction assistance and advisory project. To promote this development more effectively, it is necessary that different data related to new energies are put into order comprehensively and systematically to be retained as the basic data. Therefore, this paper collects and puts into order the latest published data on cogeneration from among other new energy technology areas, with main regard to system listing, specific introduction examples, subsidy institutions, and how other countries are working on the technologies. Hydroelectric power generation uses up head energy of water by installing power plants along a river from higher location to lower location. Similarly the cogeneration is a kind of multi-stage energy utilization (cascade utilization) system that uses up energy serially from as high oil and natural gas combustion temperature as 1,500 degrees C or higher down to temperature levels used for hot water supply and air conditioning as low as 45 to 50 degrees C. It generates electric power by using a thermal engine, and utilizes waste heat effectively. (NEDO)

  15. Report on the achievements in fiscal 1999. Surveys on the foundation for establishing industrial technology strategies (Foundation and environment improving strategies - an overall survey); 1999 nendo sangyo gijutsu senryaku sakutei kiban chosa hokokusho. Kiban kankyo seibi senryaku (zentai chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Surveys were performed on the foundation for technological innovation in Japan and other countries. Main findings obtained from the actual state survey were compiled from the two aspects of 'items having difference in international comparison' and 'main findings by nucleuses and functions'. In order to activate the economy stagnated in the 1980's, America has developed strong industrial technology policies under the initiative of the government to strengthen the competitive edge, and the result thereof appears linking with the briskness in the today's U.S. economy. In Japan, the non-competitive fund distributed uniformly to national universities and national research institutes accounts for the majority in the governmental research fund. In contrast, many of the research funds of the U.S. government are the competitive fund, whereas researchers perform their research works using these funds, including their own labor cost, and the competition is intense. America is regarded to have put a huge amount of national defense research expense and space development research expense into private business entities, which are playing a large role in developing advanced technologies. A great amount of governmental fund is injected concentratedly into researches of health, medical and bio-technologies. (NEDO)

  16. Fiscal 2000 survey report on technological trends. Survey on trend of high-density energy beam technology concerning conservation of energy; 2000 nendo gijutsu doko nado chosa hokokusho. Energy shiyo gorika ni kakawaru komitsudo energy beam technology no doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    There is a possibility that machining technology using high-density energy beam will bring an epoch-making change to micro-nano area processing. In particular, a laser beam having high controllability is indispensable. This is a report of the fiscal 2000 survey. The survey was conducted on laser beam generation, control and nano-diagnostic techniques, micro-nano optics technologies and machining technologies, with the development problems and targets summarized. Laser beam generation/control technologies, which become the basic tools for micro-nano manufacturing, were investigated, as were inspection technologies for the purpose of checking the functions of nano structures created. Particularly, the investigation elucidated the significance of development of a femtosecond solid state laser based on a semiconductor laser and the control techniques of their phase. Further, necessity was emphasized in developing X-ray probing, infrared and terahertz spectroscopy which are essential for nano-diagnostic techniques. In optics technologies, the paper described the importance of photonic crystals which enable less-than-wavelength machining or electrical beam control using interference effect. The possibility of fabricating photocatalysts with nano-particles was also mentioned, as was the manufacturing of nano-functional structures. (NEDO)

  17. Report on a commercialization fundamental investigation (in Batulicin Area, Indonesia) in relation to FY 1997 investigations on geological structures in overseas countries; 1997 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa (Indonesia Batulicin chiku) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A fundamental coal mine development investigation was carried out in Batulicin Area, Kalimantan, the Republic of Indonesia. The investigation included ground surface surveys, preparation of topographical maps and geological maps, trial drilling investigation, physical logging, chemical analysis, and infrastructure investigation. The trial drilling investigation was intended to identify the existence conditions of coal beds and coal quality, and was performed by forming grids with about 500-meter interval, and using 21 trial drillings to depths of 104 to 240 meters for a total drilling length of 3463 meters. The physical logging included electric logging, radioactivity logging and pore size logging, and the trial drilling cores were subjected to chemical analysis. For infrastructures, investigations were carried out on necessity of modifying existing roads, privilege relationship, the current status of barge loading points, water depths, and land acquisition. The result of the investigation revealed that minable coal quantity in underground mining of the coal bed B would be 13.189 million tons, and that annual production of original coal at 733,000 tons would be possible by adopting a long-wall type mechanized coal mining system. 14 refs., 99 figs., 25 tabs.

  18. Report on the survey in fiscal 1998. Basic survey on promotion of joint project implementation (Khabarovsk thermal power plant modification plan); 1998 nendo chosa hokokusho. Kyodo jisshi nado suishin kiso chosa (Khabarovsk karyoku hatsudensho kaishu keikaku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Discussions were given on the modification plan for Khabarovsk Thermal Power Plant as part of the basic survey on promotion of joint project implementation based on the COP3. The plan calls for shutting down the overaged power plant No. 1 (462.5 MW) and newly building the power plant No. 4 with high efficiency to reduce CO2 emission. The plant will use coal, which is mined extensively in the region. The plant will be a combined heat and power plant with a total power generation output of 576 MW and a total thermal output of 1140 Gcal/h. Effect of reducing CO2 emission as the result of this modification plan will be as much as about 1.2 million tons annually. The plant will use coal as fuel in the beginning, but if it uses natural gas in the future, for which pipeline construction from Sakhalin has been planned recently, the CO2 emission reducing effect will reach 2.4 million tons. Internal profitability was calculated with the CO2 price set at zero US dollars and with the foreign exchange rate varied, for a case of firing coal for 30 years. The profitability may vary largely according to the foreign exchange level, such as profit rate of 5.47% at 20 roubles to a US dollar, 11.04% at 12 roubles, and 21.22% at 6 roubles. The profitability should be judged somewhat low under the current exchange rate of 20 roubles to a dollar. Financial provision with a favorable condition is strongly desired. (NEDO)

  19. Investigation under international cooperation on the mentality/intellect-based technology. Development of mind-based technology; Shinsei chisei kiban gijutsu kokusai kyodo kenkyu chosa. Mind-Based Technology no kaihatsu ni kakawaru kenkyu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The mind-based technology (MBT) was investigated to be developed, for materializing the world where the human race and machinery live together without sense of incompatibility. Based on the human mind, the MBT is a technology to support the personal expression which respects the value judgment, diversity and individuality in the human life. For it, it is important to technologically comprehend the human mind and physiological/psychological state, and particularly, control the human will. In order to structure the social system in which the human race and technology live together, it is also important to build a life system information processing model which simulates the formation process to integrate the feeling, knowledge and conscience, together with an action system to be established. As an image to which the MBT is applied, support will be extended to the life fulfillment, personal expression and hearty communication. Development is expected toward the social security technology with robots living in the human society. Pursuing the mental richness and worthwhile life, the high-grade mature society needs the technology to communicate with the machinery gentle to the human race on the mutual interface. 21 refs., 8 figs.

  20. Fiscal 1996 research report. Basic research on energy consumption efficiency improvement for developing countries (Industry related survey for energy analysis); 1996 nendo hatten tojokoku energy shohi koritsuka kiso chosa jigyo hokokusho. Energy bunsekiyo sangyo renkan chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-05-01

    Inter-industry relations tables and energy statistics are combined for Asian countries for the preparation of energy analysis oriented inter-industry relations tables, which are used to metrically analyze Aisan nations' industrial structures and energy consumption structures for the ultimate purpose of grasping the magnitude of each industry's demand for energy. The tables prepared this year cover Korea, Indonesia, Thailand, and the Philippines. In Korea, the self-sufficiency rate of mineral fuels is low at 23.1%, which is due to its import of crude oil from abroad. It consumes 177.92-million tons (in terms of oil) of energy for its economic activities, with energy saving measures expected to work effectively here. Indonesia's mineral fuel self-sufficiency rate is high at 84.3% because it is an oil producing country. The energy it consumes for its economic activities is 179.37-million tons (in terms of oil), and energy saving measures will work effectively here. Thailand is a crude oil importing country. Its mineral fuel self-sufficiency rate is 33.4% and the energy its economic activities consume is 53.08-million tons (in terms of oil), and energy saving measures will work effectively in this country. The Philippines is a crude oil importing country and its mineral fuel self-sufficiency rate is as low as 4.8%. It consumes 22.71-million tons of energy (in terms of oil) for its economic activities, and energy-saving measures are expected to take effect here. (NEDO)

  1. Achievement report on research and development in the Sunshine Project in fiscal 1978. Surveys and studies on patents and information (Surveys on progress in research and development); 1978 nendo tokkyo joho chosa kenkyu seika hokokusho. Kenkyu kaihatsu suichoku jokyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1979-03-01

    This paper describes the surveys in fiscal 1978 on the status of progress in research and development in the Sunshine Project. Identification, evaluation and analysis were given on the status of progress in research and development and developed technologies in each project. Items of information were provided to related organizations for the purpose of mutual information exchange. The subjects include solar heat power generation, solar beam power generation, solar energy air conditioning, hot water supply systems, geothermal applications, and coals. Project teams were organized to discuss more precise identification of the current status of research and development, and increase in efficiency of the research activities. Since the Sunshine Project (which had begun in 1974) is coming close to completing the interim programs in the first term in fiscal 1980, it is thought necessary to provide assistance such as provision of items of information both for each group and on the collective basis. The basic issues at the end of the first term include presentation of the second term conception to the persons responsible of the program management, clarification of the evaluation criteria, strengthening of horizontal communication and adjustment functions in general, and feeding back of the surveys on the status of progress. Putting the basic problems in individual projects into order indicates necessity of discussion on the voucher control system, procedures of disposing of facilities after the related researches have been completed, issues of creating initial market, and expansion of technological discussions. (NEDO)

  2. Report on fiscal 2000 basic survey for coal resource exploration. Survey for development of new exploration technology (Exploration of shallow layers on the land); 2000 nendo sekitan shigen kaihatsu kiso chosa hokokusho. Shintansa gijutsu chosa kaihatsu (rikuiki senso tansa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-01

    Efforts are made to develop a high-precision high-resolution seismic reflection method, high-efficiency method for measurement in the bored hole, coal potentiality assessment system, and so forth. For the development of the seismic reflection method, studies are conducted to properly deal with a situation where there are high-velocity layers at levels shallower than the object coal bed, and a conclusion is reached that quake generation based on the pseudorandom binary sequence code will be the best for the purpose. The system was tested for verification in a producing coal mine. As for measurement in the bored hole, an on-site test was conducted for a geophysical logging system capable of determining the total sulfur content, ash, and the like, and the system was found to supply high-quality data. In developing the coal potentiality assessment system, studies were made about the basic concept of the coordination of the system with the coal GIS (geographical information system) dealing with spatial data and about the functions of the system, and a conceptual design was prepared. (NEDO)

  3. Leading research and study report for fiscal 1998. Research and study of 3-dimensional ion processing technologies; 1998 nendo sendo chosa kenkyu hokokusho. Sanjigen ion kako gijutsu no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Reported are the results of 'Research of 3-Dimensional Ion Processing Technologies.' Tasks to solve before the practical application of 3-dimensional technologies are extracted, and the possible effects of the new technologies on the creation of novel industries are investigated. In the field of new processing technologies, the special characteristics, current state, and tasks to solve are reported concerning the implantation technology, film formation technology, and hybridization which utilize plasma ion implantation. In the field of element technologies for device development, the current state and tasks of high-density plasma generation, homogeneous implantation, etc., are taken up, and the need is mentioned of inductively coupled plasma and surface wave excited plasma. As regards homogeneous implantation, the need is mentioned of technologies for forming matrix sheaths and pulsed plasma. In the field of 3-dimensional ion processing technologies application to the production of commercial goods, large items and their components such as automobiles, rollers, turbines, etc., are taken up, and the surface reforming technologies are reported, with reference made to their current state, tasks, predicted future market, concurrent technologies, feasibility of their application, the hopes and expectations they have aroused, etc. (NEDO)

  4. Survey report for fiscal 1998. Survey of creation of highly efficient renewable resources and bioconversion technologies; 1998 nendo chosa hokokusho. Kokoritsu saisei kano shigen no sosei narabini bio conversion gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A survey is conducted concerning environmentally friendly industrial technologies that utilize renewable resources, which are technologies of creating highly renewable resources and converting renewable resources by breeding industrial vegetation. In relation with the creation technologies, the state of research and development of basic technologies is surveyed, which involves the fabrication of environmental stress resisting vegetation, studies for the application of the gene expression control mechanism, introduction of multigenes and site-directed genes, etc. Concerning the respective target products expected to be produced by industrial vegetation, as much information as possible relative to genes is collected on the current state of production, metabolism in vegetation and microbials, and biosynthesis. Surveyed in relation with the bioconversion technology are the conversion of vegetation-derived polymers, construction of environmentally friendly ligno-bioprocess, conversion of sugar, production of biofuels, etc. Furthermore, the technology of treating ligneous wastes with supercritical water is surveyed, this to determine the practicality of the technology at the current stage. (NEDO)

  5. Report on technological survey in fiscal 1999. Demonstration test for smoothing grid interconnection (Collection of information by surveys in overseas countries); 1999 nendo keito renkei enkatsuka jissho shiken chosa hokokusho. Kaigai chosa ni yoru joho shushu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Surveys were performed on the institutional aspects of establishment and operation of grid interconnection guidelines in the countries advanced in introduction of discrete power supply systems. The survey items for America include: (1) summary of the status related to grid interconnection, (2) grid interconnection process, (3) methods for paying expenses for increasing power transmission facilities by means of grid interconnection, (4) dispute processing, (5) information release, and (6) software. The survey items for England, Germany, and France include: (1) summary of electricity business, (2) regulation patterns in electricity business, (3) summary of grid operating organizations, (4) connection to grid interconnection systems, and (5) the future liberalization programs. America is establishing standards for grid interconnection in discrete power supplies including photovoltaic power generation and energy storage under SCC21 of IEEE, whose conclusion will be drawn in the end of 2000. The Energy Department has an intention to give the standards the legal bases to operate them under unified requirements. Germany, England and France have all established standards for operating the grid interconnection. Market liberalization for electric power retailing is advancing in the order of America, England, Germany, and France. (NEDO)

  6. Fiscal 1997 survey report on the project on energy conservation by effectively using building energy in Indonesia; 1997 nendo chosa hokokusho (Indonesia ni okeru biru energy yuko riyo ni yoru sho energy ka project chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    As an energy conservation method for a model building, the following eight methods were selected and trially calculated of the effects. 1) adoption of high efficient illumination apparatus, 2) introduction of an illuminance control system, 3) cooling water secondary pump with invertor, 4) ventilation control for parking lots, 5) heightening of the established temperature, 6) improvement of the 24-hour run chiller, 7) elevator with invertor, and 8) introduction of the photovoltaic power generation. As a result, it was found out that energy was totally reduced by about 3,837.4 MWh/yr or 25.6%. If viewed from the amount of reduction in greenhouse gas, the amount of CO2 emitted from office buildings, approximately 0.22 million t-C/yr, decreases to approximately 0.16 million t-C/yr. Further, approximately 0.93 million t-C/yr, the amount of CO2 emitted from commercial use facilities such as office buildings, department stores and hotels is reduced to about 0.69 million t-C/yr, thanks to the effect of the project on energy saving buildings, which made a CO2 reduction by approximately 0.24 million t-C/yr possible. Validity of the project on energy conservation in Indonesia was confirmed. 2 refs., 55 figs., 38 tabs.

  7. FY 1990 report on the survey of geothermal development promotion. Survey of geothermal water (No.34 - Kaminoyu/Santai area); 1990 nendo chinetsu kaihatsu sokushin chosa. Nessui no chosa hokokusho (No.34 Kaminoyu Santai chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-12-01

    For the contribution to elucidation of the structure of geothermal reservoir in the Kaminoyu/Santai area in the southwest part of Hokkaido, jetting test/sampling of geothermal fluid/analysis of properties were carried out in Structural Drilling Well N2-KS-2. The induced jetting of N2-KS-2 was conducted by the air lift method in consideration of the well temperature, state of lost circulation while drilling and results of the water pouring test. As a result, the mean jetting amount of geothermal water was 202.4L/min. The total pumping amount was 559kL, which is equal to approximately 119 times as much as the volume of well. The maximum temperature was 95.9 degrees C, resulting in no steam jetting. The pH of geothermal water was 7.41-8.44, electric conductivity was 9,620-10,450 {mu}s/cm, and the Cl ion concentration was 2,204-2,545 mg/L, which are almost stable. Properties of geothermal water is classified into an alkalescent CL-SO{sub 4} type. As a result of the study, the geothermal reservoir of N2-KS-2 is basically formed by a mechanism of a mixture of the surface water and the deep geothermal water that is similar in isotope to the geothermal water of Nigorikawa production well, which indicated a tight relation in the origin with the group of Kaminoyu hot spring. (NEDO)

  8. FY 1993 report on the survey of geothermal development promotion. Survey of geothermal water (No.36 - Amemasu-dake area); 1993 nendo chinetsu kaihatsu sokushin chosa. Nessui no chosa hokokusho (No.36 Amemasu dake chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-01-01

    As a part of the survey of geothermal development promotion in FY 1993, survey of geothermal fluid was made using a precise structure drilling well N5-AM-5 as exploration well in the Amemasu-dake area, Hokkaido. The induced jetting of geothermal fluid was carried out by the Swabbing method in the total number of times of 185 in 11 days at 10-20 times/day, but did not result in the jetting of geothermal water. The sampling of geothermal water was conducted by guiding the geothermal water that overflowed the guide pipe to the tank. The temperature of geothermal water indicated approximately 20 degrees C in the 1st time and 40-60 degrees C in and after the 2nd time every day. The electric conductivity of geothermal water was 2.033 mS/cm, chlorine ion concentration was 420-500 ppm, and pH value was 7.17-7.72. As a result of the survey, it was presumed that the geothermal water of this well originated in the meteoric water around the area and formed slightly supported by emitted volcanic matters. As to the geochemical temperature, the silica temperature indicated about 120 degrees C and the alkali ratio temperature did about 180 degrees C. It was considered that there possibly existed geothermal reservoirs of approximately 180 degrees C in alkali ratio temperature around the well. (NEDO)