WorldWideScience

Sample records for chishitsu kozo nado

  1. FY 1999 report on the survey of the overseas geological structure, etc. Japan-Indonesia joint Tanjung Enim coal exploration project; 1999 nendo kaigai chishitsu kozo nado chosa hokokusho. Nippon Indonesia sekitan kyodo tansa Tanjung Enim project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper summed up the FY 1999 results of the survey conducted based on the agreement on the Tanjung Enim IV coal exploration project which was concluded between NEDO and Indonesia's Ministry of Mining Energy. The survey was made for an area of approximately 40km{sup 2} which is a north block of the south Arahan region, Tanjung Enim, South Sumatra, Indonesia. To grasp the succession of strata/rock facies/geological structure and the state of existence of the coal seams to be drilled, surveys were conducted on ground surface and boreholes. A total of 10 holes was test-drilled, and all the boreholes were physically logged. As a result of the survey, each of A1, A2, B, C and E coal seams was confirmed as main seams. A1, A2 and B seams are low in ash and sulfur contents with heating values of approximately 4,800 kcal/kg, C seam is high in sulfur content, and E seam is high in heating value, 6,000 kcal/kg. As coal seams for open pit mining, existence of A, B and C seams is expected which lay in the shallow part from ground surface to sea level of 0m and in the range of depth of approximately 100m. The proved coal reserves of these coals were estimated at 189 million tons. (NEDO)

  2. Fiscal 2000 report on financially supported geological structure survey overseas. Basic survey for coal resource exploitation (Research on underground probing technology); 2000 nendo kaigai chishitsu kozo chosahi nado hojokin (sekitan shigen kaihatsu kiso chosa) konai tansa gijutsu chosa hokokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the work of searching for coal beds, comparison is made between the geological structure of the object area, which is predicted, before actual investigation, by a close scrutiny of the result of oceanic pilot boring conducted in the past, result of geophysical exploration, and the geological features of galleries already in presence in the vicinity, and the result obtained from galleries drilled actually for the investigation. The investigation was conducted at the Ikeshima coal mine, Nagasaki Prefecture. In this fiscal year, 5 investigation galleries were drilled, totalling 1640m in length, and, in the mine, geological surveys, survey and measurement, coal quality evaluation, water emergence investigation, boring for coal, etc., were carried out. Comparison was made, and, though in the 2nd Minami No. 06 air duct there was no important difference detected between the prediction and the actual result, some faults were found to exist which had not been predicted by seismic exploration on the ocean. In the 2nd Minami No. 5 air duct, the actual geology was not different from the predicted geology, this endorsing the usefulness of boring for coal. In the 2nd Minami No. 01 gallery, direction and inclination were not greatly different from what had been predicted, but some faults which had not been predicted were discovered. These faults had escaped the scrutiny of neighboring coal beds and pilot boring. (NEDO)

  3. FY 2000 survey of the geological structure overseas, etc. Japan-China joint coal exploration - Yu Xian project; 2000 nendo kaigai chishitsu kozo nado chosa - futai shiryoshu. Nippon Chugoku sekitan kyodo tansa Yu Xian project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This data book summarized the proceedings and the technical report of the management committee on the Japan-China geological structure survey based on the consultation concluded between NEDO and China's bureau of coal field geology and a report meeting on the Yu Xian project. In the exploration, conducted were the boring survey of 10 boreholes, seismic survey of 2D (71 traverse lines, 180.105km) and 3D (1.5km{sup 2}), VSP (6 holes (345 shots)) and the low velocity band survey (2,072 shots). The geological structure of the area presented the syncline structure with a gentle line associated with foldings and a number of faults and was classified into the medium class or the class of a little complication in the Chinese standard. The number of the faults confirmed in this exploration totaled 57. Coal reserves by coal seam were 157.22 million tons at No. 5 seam and 102.57 million tons at No. 1 seam. The total amount of the two seams was 79.1% of the total coal amount in all area. The coal quality of Nos. 1 and 5 was brown coal - flame coal in the Chinese classification, and subbituminous coal B - subbituminous coal C in the ASTM classification. The coal, however, cannot be used for process raw coal. There is a technical potentiality of the fixed bed pressurized gasification. (NEDO)

  4. Report on the FY 1992 basic survey for industrialization related to the survey of overseas geological structure (Embalut West area, Indonesia); 1996 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa hokokusho (Indonesia Embalut nishi chiku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    The paper reported the FY 1992 basic survey for the coal mine development/industrialization in the Embalut West area of Indonesia. The geological structure in the survey area is under the Loa Haur Syncline which lies approximately north and south to the west of the area, and is regarded as the stabilized structure having no faults. The three beams from the upper part, S14, S13 and S12, are assumed to be the coal seams to be drilled. The average seam thickness is 1.17, 2.35 and 3.09m, respectively, and the continuity is good. In S14 beam, which is thin, it is difficult to mine coal using equipment. The theoretical minable reserve of the three coal seams is 18,859,000 tons. The recoverable coal reserve is 12,258,000 tons at a mining recovery of 65%. In case of annual production of 0.4 million tons, it is possible to mine more than 30 years. The coal is classified into a subbituminous coal-brown coal rank of the JIS coal classification. It is high in water content and medium in heating value, but is an environmental protection type with low ash and low sulfur content. In the case of mines in the Mahakam River basin, barge transport is indispensable. For sea transportation, the following should be studied in the light of the international price competition: reinforcement of shipping facilities on Mahakam River, increase in barge size, joint use of Balikpapan Coal Center, etc. (NEDO)

  5. Report for fiscal 1998 on basic commercialization survey related to geological structure surveys in overseas countries (Manguerra, the Philippines); 1998 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa (Philippines Manguerra) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Commercialization survey was performed on the mines in the Manguerra district in the Philippines by means of geological structure surveys. The site surveys included geological and test drilling surveys, and those on conditions for developing underground mining mines, and infrastructures. The geological survey area spread out about 5 km{sup 2}, two test wells were drilled (to depths of 330 m and 290 m), trench survey was performed on 58 locations, and coal sample collection and analysis were carried out on eight locations. Furthermore, surveys were extended to the Manguerra mine operating status, on-the-ground facilities, roads for transportation, marketing, and related laws and regulations. As a result of the surveys, the Manguerra district was suggested of frequent sea water inundation into the coal field, leading to a view that the district is unstable from the viewpoint of development of coal beds. However, samples collected from the existing mining area indicated to have less water content and ash and high calorific power. The coal has high product value. The result of coal quantity calculation indicated 320122 tons as the total of defined and estimated quantity. The great depth mining plan was prepared from the viewpoints of actual yield, productivity, safety aspects, technological enhancement, and suppression of additional investments to minimum. (NEDO)

  6. FY 1999 Report on overseas geological structure surveys. Joint Japan-China Yu Xian exploitation project (Attachments); 1999 nendo kaigai chishitsu kozo nado chosa futai shiryo. Nippon Chugoku sekitan kyodo tansa Yu Xian project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This reports provides the attachments for the report JN0041264. The contents include (1) minutes of the fourth steering committee, (2) technical reports presented to the fourth steering committee (I: report on FY 1998 joint exploitation works, and II: report on FY 1999 joint exploitation works), (3) minutes of the fifth steering committee, and (4) technical reports presented to the fifth steering committee (I: report on FY 1999 joint exploitation works, and II: report on planned FY 2000 joint exploitation works). The item (1) includes approval of the reports on FY 1998 and 1999 joint exploitation works. The item (2)-I report includes seismic exploitation test works, observation work results and quality evaluation thereof; drilling exploitation work results, quality evaluation thereof, exploitation results and evaluation thereof; exploitation results and evaluation thereof; and proposals. The item (2)-II report includes seismic exploitation, drilling exploitation, and man-hours of the workers from the both countries. The item (3) includes approval of the reports on FY 1999 joint exploitation works and planned FY 2000 joint exploitation works. The (4)-I report includes seismic exploitation work results and evaluation thereof, seismic exploitation test works, drilling exploitation work results, quality evaluation thereof, exploitation results and evaluation thereof, and proposals for the future works. The (4)-II report includes seismic and drilling exploitation plans, and numbers and periods of the workers from the both countries. (NEDO)

  7. Report on the FY 1993 basic survey for industrialization related to the survey of overseas geological structure (Tebulan East area, Malaysia); 1993 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa (Malaysia Tebulan higashi chiku) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The survey was conducted based on 'Scope of work for detailed coal exploration in the Tebulan East block of the Merit Pila coal field, Sarawak, Malaysia' concluded on June 19, 1993 between NEDO and Global Mineral which owns the mining right. The field survey was for the geological survey, survey of conditions of open pit mining, and infrastructure survey. The confirmed/estimated coal amount totaled 22,65 million tons in 4 coal seams. The all sulfur content is low, approximately 0.12%. The heating value is 5,820 kcal/kg. As to the infrastructure, various conditions are good for transportation, shipping facilities, etc. from mine site to truck transport/barge transport/external route shipping. The drilling was planned to be made by open pit mining by the truck and shovel system, and the scale of the planned production was 0.3 million tons. The ash is low in amount, and there was no coal preparation. Clean coal is produced by crushing, sieving and washing. Attached were the borehole log (JN9940782), route map, and trench sketch (JN9940783). (NEDO)

  8. Fiscal 1998 overseas geological structure survey. Japan-China joint coal survey Mei-Xian project; 1998 nendo kaigai chishitsu kozo nado chosa hokokusho. Nippon Chugoku sekitan kyodo tansa Mei-Xian project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Japan-China joint coal survey was made through seismic prospecting by Japanese group and drilling prospecting by Chinese group. Mei-Xian mine property includes coal seams of the Jurassic period, and is covered with the quaternary period stratum without any coal seam. The base of the quaternary period stratum exists at depth of 50-400m, while the coal seams at depth of 300-700m. Among 11 existing seams, the 1st and 5th seams are main objects for prospecting. The 5th seam of 0.2-8.96m (2.95m in average) thick is the most expected important one, distributing all over the mine property. The 5th seam also has branch seams spreading over 2.5km from east to west and 1.2km from south to north in the center part of the mine property. The 1st seam of 0-8.62m (2.90m in average) thick is most thick in the south part of the mine property. The theoretical amount of coal deposits in the whole coal seam is estimated to be nearly 290,000,000t by Chinese group (nearly 50% of it in the 5th seam). That is also estimated to be nearly 346,000,000t by Japanese group (155,000,000t in the 5th seam). Both 1st and 5th seams are composed of sub-bituminous coal. (NEDO)

  9. Fiscal 2000 survey of geological structures overseas. Exchange of engineers with Indonesia (Coal mining technology); 2000 nendo kaigai chishitsu kozo nado chosa hokokusho. Gijutsusha koryu jigyo (tanko gijutsu bun'ya) Indonesia

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Indonesia rich in coal resources consumed 70-million tons of coal in 1999, which covered 17% of its total energy demand. It is estimated that as much as 120-million tons will be produced in 2005, and it is expected that underground mining will increase. Under such circumstances, Indonesia strongly desires that Japan's underground mining technologies be transferred to Indonesia. For the transfer of technologies especially involving production control and management out of Japan's underground mining technologies, Japan dispatched engineers to Indonesia under a mining engineer exchange project, and received and trained Indonesian engineers. Under the engineer exchange project, five engineers were dispatched to Indonesia and gave lectures and on-site training in the period July 9 through August 5, 2000. Japan received seven engineers, who were given lectures and training at the Ikeshima mining field of Matsushima Coal Mining Company in the period November 12 through December 12, 2000. (NEDO)

  10. FY 2000 report on the survey of the overseas geological structure. Japan-China joint coal exploration - Yu Xian project; 2000 nendo kaigai chishitsu kozo nado chosa hokokusho. Nippon Chugoku sekitan kyodo tansa Yu Xian project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The geological survey was carried out which is needed for coal mine design in the Yu Xian coal mine area, Yu Xian coal field, Hebei province, China. The term of survey was 5 years from 1996 to 2000. Activities are mainly for seismic survey and boring survey. Japan was in charge of the seismic survey, and China in charge of the boring survey. Both attained the goal. The results of the activities were summed up in the following 7 items: 1) outline of the survey; 2) general investigation; 3) state of the exploration related materials/machinery; 4) field survey; 5) items of survey; 6) results of the survey; 7) conclusion. In 6), the geological analysis, coal quality survey and coal amount survey were conducted. In the geological analysis, analyzed were the succession of strata, geological structure, and the situation of existence of coal seams. In 7), the following were made clear: geological structure of the survey area, coal seam, coal quality, hydrological geology, other conditions of drilling technology, and coal amount. The coal amount was 328.34 million tons in a total of A/B/C class coals. The total coal amount of Nos. 1 and 5 coal seams was 259.79 million tons, which was 79.1% of the total coal amount in all area. The average thickness of Nos. 1 and 5 coal seams, which are the main minable coal seams, was 3.10m and 2.66m, respectively. (NEDO)

  11. Report on a commercialization fundamental investigation (in Batulicin Area, Indonesia) in relation to FY 1997 investigations on geological structures in overseas countries; 1997 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa (Indonesia Batulicin chiku) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A fundamental coal mine development investigation was carried out in Batulicin Area, Kalimantan, the Republic of Indonesia. The investigation included ground surface surveys, preparation of topographical maps and geological maps, trial drilling investigation, physical logging, chemical analysis, and infrastructure investigation. The trial drilling investigation was intended to identify the existence conditions of coal beds and coal quality, and was performed by forming grids with about 500-meter interval, and using 21 trial drillings to depths of 104 to 240 meters for a total drilling length of 3463 meters. The physical logging included electric logging, radioactivity logging and pore size logging, and the trial drilling cores were subjected to chemical analysis. For infrastructures, investigations were carried out on necessity of modifying existing roads, privilege relationship, the current status of barge loading points, water depths, and land acquisition. The result of the investigation revealed that minable coal quantity in underground mining of the coal bed B would be 13.189 million tons, and that annual production of original coal at 733,000 tons would be possible by adopting a long-wall type mechanized coal mining system. 14 refs., 99 figs., 25 tabs.

  12. Fiscal 1998 geological survey overseas. Report on Tanjung Enim project for Japan-Indonesia joint coal exploration; 1998 nendo kaigai chishitsu kozo nado chosa hokokusho. Nippon Indonesia sekitan kyodo tansa Tanjung Enim project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For disclosing stratigraphy and lithofacies and for clarifying the status of coal beds in the southern Arahan area (55km{sup 2}), South Sumatra, ground surface exploration, borehole drilling, borehole geophysical logging, and seismic reflection monitoring were carried out. The survey covered a rectangular area, 11km from east to west and 5km from north to south and 60m to 130m in elevation. In the ground surface exploration effort, trenching was performed at three spots in coal bed outcrops in an quasi-accurate survey with route gaps of roughly 1,200m. Ten boreholes were drilled. The deepest one was 282.20m deep and the shallowest one 117.80m deep, with the total drilled length measuring 1,643.70m. Seismic reflection monitoring was implemented using three traverse lines (two running north to south and one running from east to west), with the three lines measuring 10.92km in total. VSP (vertical seismic profiling) was carried for borehole ASN17 only. The findings are that there are four kinds of coal beds, that is, A2, B, C, and E spreading all over the area, that their thicknesses are estimated to be 12m, 18m, 7m, and 6-8m, respectively, and that coal beds A2, B, and C are packed into between 80m-deep and 150m-deep levels. (NEDO)

  13. FY 1998 annual report on the survey on overseas geological structures. Project for exchanging engineers (coal mining technology area) (Vietnam); 1998 nendo kaigai chishitsu kozo nado chosaa. Gijutsusha koryu jigyo (tanko gijutsu bun'ya) (Vietnam)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The project for exchanging engineers has been implemented, in order to improve production and managemental techniques of coal mining engineers in the Asia-Pacific region, promote smooth and efficient projects for surveying overseas geological structures, and facilitate stable supply of overseas coal to Japan. The FY 1998 project was concentrated on Vietnam, to which Japanese coal mining engineers were sent, and from which production management engineers were invited to Japan as trainees. The Japanese engineers sent to Vietnam educated the underground coal mining techniques. The Vietnamese management engineers invited were trained for, e.g., production management techniques (e.g., those for workplaces and organizations) in the Japanese mines, administrative management techniques, and techniques to improve safety and productivity in the mines. Coal Energy Center and Taiheiyo Mining's Kushiro Mine provided training facilities. (NEDO)

  14. FY 1999 Report on overseas geological structure surveys. Joint Japan-China Yu Xian exploitation project; 1999 nendo kaigai chishitsu kozo nado chosa hokokusho. Nippon Chugoku sekitan kyodo tansa Yu Xian project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This project is based on the (agreement of the joint exploitation project for Yu Xian block in Yu Xian coal mine, Province of Hepei by Japan's NEDO and China's Coal Geological Bureau), signed on October 4, 1996. The joint project mainly comprises seismic exploitation and test drilling, Japan being mainly responsible for the former and China for the latter. The final report will be drawn jointly for the geological survey results necessary for designing coal mines. The Yu Xian block contains the Jurassic coal seams, which are covered by the Quaternary bed and not exposed to the surface. The Quaternary bed base is 50 to 400 m deep from the surface, and coal seams are 300 to 700 m deep also from the surface. A total of 11 coal seams are located in the Xiahuayuan strata as the coal-bearing strata. The first and fifth seams are most promising ones. In particular, the fifth seam is thick (0.2 to 6.91 m thick) and distributed throughout the block. It is estimated that 8 coal seams have a total coal quantity of approximately 346 million tons. (NEDO)

  15. Fiscal 1998 overseas geological structure survey report on the engineer interchange project (coal mine technology field), Indonesia; 1998 nendo kaigai chishitsu kozo nado chosa gijutsusha koryu jigyo (tanko gijutsu bun'ya), Indonesia hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project aims at improvement of coal mining technology and productivity in Indonesia by Japanese production control technology and business management technology for underground coal mining, through interchange of coal engineers between Japan and Indonesia. This project is composed of the short- term and long-term dispatch project of engineers to Indonesia, and the training project of Indonesian engineers in Japan. In fiscal 1998, the short-term dispatch was made for the training in Indonesia on underground coal mine development (development planning, pit mouth selection, main gallery design, mining system selection, transport planning, ventilation planning, under-river mining, mine water proofing, drainage). The long-term dispatch was made for contact and negotiation with concerned Indonesian organizations, support of the training project, and collection of information on the trend of Indonesian economy and energy, and the present and trend of the coal industry for conducting smooth and effective engineer interchange. (NEDO)

  16. Report for fiscal 1999 on basic commercialization survey related to geological structure surveys in overseas countries (Kalewa area, Myanmar); 1999 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa (Myanmar Kalewa chiku) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Commercialization survey was performed on the coal beds in the Kalewa area in the Union of Myanmar by means of geological structure surveys. The site surveys included on-the-ground survey, test drilling survey, sample collection and analysis, and infrastructure survey. The on-the-ground survey area spread out about 5.5 km{sup 2}, wherein nine test wells were drilled (for total distance of 2,046.74 m), and coal and rock sample collection and analysis were carried out on six samples. The infrastructure survey was performed on coal transporting roads, and barge loading planned points and facilities. As a result of the test drilling survey, existence of coal beds with thickness of 4 ft, 9 ft and 6ft was identified. Since the 9-ft bed in particular exists stably with inclination of 40 to 42 degrees over the whole subject area, it was made clear that the bed can be the object of mining as the main coal bed. The coal is the ordinary coal with such good qualities as ash content of 4.72%, total sulfur content of 0.22%, and total calorific power of 6,500 to 6,570 kcal/kg. The defined coal quantity for the 9-ft bed is four million tons, or 7.7 million tons in total if the estimated coal quantity is added. The quantity will amount to 15.3 million tons when those of the 4-ft and 6-ft beds are added. (NEDO)

  17. FY 2000 report on the survey of geological structures overseas, etc. Volume 1. 'Tanjung Enim IV Coal Exploration Project between Japan and Indonesia'; 2000 nendo kaigai chishitsu kozo nado chosa hokokusho. 1. Nippon Indonesia sekitan kyodo tansa Tanjung Enim project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The paper summarized the results of the surveys in the final fiscal year (FY 2000) and in the past five years of the Tanjung Enim IV Coal Exploration Project between Japan and Indonesia. In FY 2000, conducted in the South Arahan area were the surface reconnaissance (50km+ACI-2), boring survey (11 holes, 1,847m), borehole physical logging (11 holes), reflection method seismic survey (3 traverse lines), pumping test, coal analysis (112 specimens), etc. As a result of the exploration/study made during 5 years, coal reserves in the South Arahan area were 223 million tons in north block (proved coal reserves: 213 million tons) and 332 million tons (proved coal reserves: 303 million tons) in south block. The coal in the area is in the depth of {+-}0m from surface, and the coal reserve is enough for large scale open pit mining. Further, coal reserves in the Banjarsari area were 442 million tons (proved coal reserves: 330 million tons) in the whole area and 223 million tons (proved coal reserves: 214 million tons) in the syncline part. About the syncline part promising as that for open pit mining, the overburden ratio was divided into three for calculation: 2:1, 3:1 and 4:1 or below. (NEDO)

  18. Report on the FY 1993 basic survey for industrialization related to the survey of overseas geological structure (Muara Lakitan area, Indonesia). Tables and drawings; 1993 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa hokokusho (Indonesia Muara Lankin chiku). Hyo oyobi zumen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    These are tables and drawings for the FY 1993 basic survey for the coal mine development/industrialization in the Muara Lakitan area of Indonesia. The geological structure in the survey area is under six sets of the anticline/syncline structure which have an NW-SE axis of fold, and exposes the Muaraenim seam repeatedly. The theoretical coal reserve in the depth down to 200m of each of the seams, Nos. 1, 2, 5, 12 and 13, which are great in coal seam change and exist relatively stably, is 143 million tons. The depth for adoption of the shovel/truck system open pit mining seems to be 50m or shallower, and the production is to be approximately 70 million tons. The coal is classified into a subbituminous coal-brown coal rank of the JIS classification. As tables, included were a table of the calculation of coal amount by seam and a table of the analytical result of coal by seam. As drawings, included were borehole logs of coal seam by boring, diagrams of thickness by seam such as the seam thickness/diagrams of thickness by seam such as the coal thickness, diagrams of range of calculating the coal amount, etc. Besides, in relation to coal properties, the report included value diagrams by seam of the inherent moisture, the ash, the volatile matter, the fixed carbon, the heating value, and the total sulfur content. (NEDO)

  19. Report on the FY 1995 basic survey for industrialization related to the survey of overseas geological structure (Pondok Labu East area, Indonesia). Data attached 3 (BIP survey report); 1995 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa (Indonesia Pondok Labu higashi chiku) hokokusho. Tenpu shiryo 3 (BIP chosa hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The survey was conducted based on 'Scope of work for detailed coal exploration in the Pondok Labu East area of East Kalimantan Province, Kalimantan, Indonesia' concluded on June 16, 1995 between NEDO and P.T. Tanito Harum which owns the mining right. This is a BIP survey report. The strike/dip read from the isobath diagram drawn from the result of the boring little agreed with the stratification in the BIP survey. The BIP stratification is greater in strike and dip than in depth. The latter possibly includes false beds and surfaces cut-off/separated by channel, but roughly speaking the structure becomes such a structure as in the isobath diagram. It suggests that there is local undulation everywhere. Judging from the appearance frequency of open type cracks and the size of hole, there are no problems of the crack type decline at frequency of less than one per 5m at the time of drilling mine roadway. The state of upper/lower basement was not good. Refer to the paper (JN9940854). (NEDO)

  20. Report on technological achievements in fiscal 1999. Survey on geological structures in overseas countries, 'Japan-Vietnam joint coal exploration project on Red River delta'; 1999 nendo kaigai chishitsu kozo nado chosa hokokusho. Nippon Vietnam sekitan kyodo tansa Red River delta project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-06-01

    With an objective to identify stratigraphy, geological structures, coal bed existing status, and coal quality of major coal beds in the north and central district of the area to be surveyed in the Red River delta, test well drilling, physical and seismic exploration, and coal composition analyses were performed. The area to be surveys is a typical delta where irrigation canals are running in all directions. Three test wells were drilled with drilling lengths of 640 m for TD3, 700 m for TD4 and 900 m for TD5. Coring was performed to depths greater than the Tertiary deposit. The seismic exploration was executed along three exploration lines. Total distance was 25 km. In addition, the VSP investigation was carried out on TD3 and TD5. The stratigraphy is composed from below of the Phu Cu bed (Neogene period: marine deposit) , the Tien Hung bed (Neogene period: continental deposit), and the Tai Doung bed (quaternary deposit), in which the bed that holds coal beds is the Tien Hung bed. The beds are very stable as the geological structure, but the constituting rocks are soft and fragile. Anticipated coal beds exist in depths greater than 1000 m. The coal quality is of low ash, low sulfur, medium in calorific power, and contains little gas. (NEDO)

  1. 2D resistivity survey in complex geological structure area. Application to the volcanic area; Fukuzatsuna chishitsu kozo chiiki ni okeru hiteiko nijigen tansa. Kazangan chiiki deno tekiorei

    Energy Technology Data Exchange (ETDEWEB)

    Asakawa, S; Ikuma, T; Tanifuji, R [DIA Consultants Co. Ltd., Tokyo (Japan)

    1996-05-01

    Introduced herein is an application of 2D resistivity survey to a volcanic rock area where the survey result is difficult to interpret because of its complex geological structure. In a dam site survey, main problems involve the permeability of water through faults and weathered, altered zones. At this site, a 2D resistivity survey was conducted, a 2D geological structure was deduced from the resistivity section, and the result was examined. It was found that resistivity distribution was closely related to hydrographic factors, but no obvious correlation was detected between rock classes and R, Q, and D. In conducting investigations into a section planned for a highway tunnel, it was learned that the problem was a volcanic ash layer to collapse instantly upon absorbing water, and the distribution of the ash layer, not to be disclosed by boring, was subjected to a 2D resistivity survey. The survey was conducted into the structure above where the tunnel would run, and further into the face, and studies were made about what layer was reflected by the resistivity distribution obtained by analysis. The result of the analysis agreed with the details of the layer that was disclosed afterward. 4 figs., 1 tab.

  2. Report on the FY 1998 geological structure survey. North Hay Gulch area, State of Colorado, the U.S.; 1998 nendo kaigaitan kaihatsu kanosei chosa hojo jigyo chishitsu kozo chosa hokokusho. Beikoku Colorado shu North Hay Gulch chiiki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-02-01

    Test boring at 21 places and core sampling were conducted during September-November 1998 along the ridge to the west of Hay Gulch and in the direction crossing the northwest of the drainage canal and National King Coal Mine (NKC coal mine). It was found that A layer which NKC coal mine is now drilling is the upper part of A coal seam where the seam bifurcates. The boundary to the west of the thick A coal seam is not clear, and there is a possibility that more reserve from the thick coal seam and single seam exists toward Cherry Creek. In the existing coal drilling area, the lower A seam existing under the upper A seam becomes thin rapidly, and the seam thickness becomes less than 1 foot. The average thickness of thick coal seams is 9.9 feet, and the area is 780 acres along the ridge. The upper A coal seam except the above is 5.5 feet in average seam thickness and 910 acres in area. The reserve is 23 million tons. As to the quality of thick coal seam, the average heating value is 7,089 kcal/kg, sulfur content 0.68%, and ash content 7.50%. As coal drilling conditions, the same level as or higher than those of NKC coal mine is expected. (NEDO)

  3. Borehole geophysics for delineating the geological structure in the Sakonishi prospect, the Hida area, Japan; Hida chiiki Sako nishi chiku ni okeru boring ko riyo butsuri tansa ni yoru chishitsu kozo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Katayama, H.; Hishida, H.; Yoshioka, K. [Metal Mining Agency of Japan, Tokyo (Japan)

    1997-05-27

    In order to discuss effectiveness of physical exploration in the Sakonishi prospect in the Hida area, physical exploration was carried out by utilizing bored wells. This area contains the Kamioka mine, one of the major base metal mines in Japan, where electrical exploration has been attempted several times in the past. No effective results have been obtained, however, because specific resistance contrast between mine beds and base rocks is too small, and the topography is too steep making site workability inferior. As part of the investigations on geological structures over wide areas, electrical logging (specific resistance and natural potential) was performed in fiscal 1995 and 1996 by utilizing the boreholes. Induced polarization logging was also conducted on the same boreholes. A traverse line on the ground with a length of 600 m and boreholes were used to execute specific resistance tomography. Clear extraction was possible on a fault structure which is thought related with limestone distribution and mine bed creation. However, it was not possible to identify upward continuity of zinc ores expected in the exploration. Because of not large a specific resistance contrast between zinc ores and base rocks, it is difficult to find mine bed locations only from the information on the specific resistance. 5 refs., 5 figs., 1 tab.

  4. Fiscal 2000 survey report on overseas geological structure, etc. Project for exchanging experts - Exploration technology (Indonesia); 2000 nendo kaigai chishitsu kozo to chosa hokokusho. Gijutsusha koryu jigyo - Tansa gijutsu bunya (Indonesia)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the stabilization of coal supply/demand in the APEC (Asia-Pacific Economic Cooperation Conference) region and for the stable supply of coal to Japan, Japanese engineers and experts were dispatched to Indonesia, where coal production was remarkably increasing and efforts were being actively exerted to develop new coal mining fields, for training Indonesian specialists there, and Indonesian specialists were invited to Japan for training here. Japanese instructors on dispatch delivered lectures on coal geology, exploration, and exploitation at the human resource development center of Bandung City during the period July 20 through August 4, 2000, which was followed by a coal outcrop survey training session in the field. The trainees were from Kalimantan, Sumatra, Java, etc., and numbered 30. The trainees invited to Japan received lectures and training related to coal geology, exploration, and mining programs during the period October 19 through November 18, 2000, at the Geological Survey of Japan, Agency of Industrial Science and Technology, Ministry of International Trade and Industry; Matsushima Coal Mining Co., Ltd.; Enzan Plant, Tone Corporation; DIA Consultants Co., Ltd.; and Mitsubishi Materials Corporation. (NEDO)

  5. FY 1992 report on the survey of geothermal development promotion. Geological structure (geology/alteration zone) survey (No. A-1 - Haneyama area); 1992 nendo chinetsu kaihatsu sokushin chosa chijo chosa hokokusho futai shiryo. Chishitsu kozo (chishitsu henshitsutai) chosa hokokusho (No. A-1 Haneyama chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-05-01

    For the purpose of elucidating a possibility of existence of geothermal reservoirs in the Haneyama area, Oita Prefecture, survey of the geological structure (geology/alteration zone) was conducted. The survey was made for the area of 280km{sup 2} lying from Kusu Town to Kokonoe Town, Oita Prefecture in terms of the route survey of 174km, fabrication/judgement of 52 rock slices, whole rock chemical analysis of 21 rocks, age determination, analysis of rock mineral, X-ray diffraction, literature collection, etc. As a result of the survey, the following conclusion was obtained. When considering a possibility of existence of heat source near this area, the area near the present volcanic front was regarded as promising. The fracture structure in the depths seen in the gravity structure (part of sharp dip of gravity) is more closely related to activity of geothermal water than the active structure of E-W system near the earth surface newly formed and is important when considering the existence of geothermal resource. The periphery of the Shishimuta sedimentation zone where Takigami, Oodake, Hacchobaru and Oguni are located was especially regarded as an area propmising of geothermal energy. In the survey area, the geothermal potential was the highest near Noya - Mizuwake Pass. (NEDO)

  6. Desempenho em 200 m nado crawl: índice de coordenação, tempo propulsivo e cinemática de nado

    Directory of Open Access Journals (Sweden)

    Marcos Franken

    2016-07-01

    Full Text Available DOI: http://dx.doi.org/10.5007/1980-0037.2016v18n3p311   O objetivo deste estudo foi comparar índice de coordenação, tempo propulsivo, duração das fases da braçada e parâmetros cinemáticos ao longo de 200 m nado crawl. Variáveis foram comparadas entre os quatro trechos de 50 m (T1 a T4 em quinze nadadores competitivos (idade: 21,1 ± 7,1 anos; estatura: 180,1 ± 6,1 cm; envergadura: 187,3 ± 8,1 cm; massa corporal: 72,1 ± 10,1 kg; melhor desempenho na prova: 77,5 ± 4,7% do recorde mundial. Obtiveram-se os dados com duas câmeras de vídeo (60 Hz - acopladas a um carrinho sobre trilhos na lateral da piscina, para imagens simultâneas do plano sagital do nadador: abaixo da linha da água e acima da linha da água. Frequência média de ciclos, comprimento de braçada (assumida como a distância média percorrida pelo corpo a cada ciclo e velocidade média de nado foram obtidos com cronometragem manual. Ao longo dos 200 m, o índice de coordenação não se alterou (p > 0,05, mas houve incremento da frequência de ciclos (p < 0,05 e redução da distância percorrida por ciclo (p < 0,05. Entre T1 e T2, houve incremento do tempo propulsivo (p < 0,05 e entre T1 e T4, da duração da fase de puxada (p < 0,05. Velocidade de nado diminuiu apenas entre T1 e T2 (p < 0,05. Ao longo de 200 m nado crawl, nadadores bem treinados incrementam tempo propulsivo, duração da fase de puxada e frequência de ciclos de braçadas, tais mudanças podem ser devidas à tentativa de manutenção da velocidade ao longo dos 200 m.

  7. Flotabilidad y similitud del nado de Manta birostris(Elasmobranchii: Myliobatidae con el ciclo de vuelo de Columba livia(Aves: Columbidae

    Directory of Open Access Journals (Sweden)

    Iván Meza Vélez

    2013-12-01

    Full Text Available Se analizó la física de la flotación en la mantarraya Manta birostrisy se comparó el nado con el ciclo de vuelo de la paloma doméstica Columba livia, con la finalidad de encontrar similitudes y diferencias en las locomociones y las leyes físicas que intervienen. Se demostró que uno de los dos ciclos de nado estudiados de esta especie posee tres de las cuatro fases principales del ciclo de vuelo de la paloma doméstica. También se demostró un “efecto paracaídas” en M. birostris, el cual le ofrece una ventaja en su locomoción. Adicionalmente, se describió cómo el concepto físico de torque se aplica al giro de esta especie.

  8. FY 2000 report on the survey of geological structures overseas, etc. Volume 2. 'Tanjung Enim IV Coal Exploration Project between Japan and Indonesia'; 2000 nendo kaigai chishitsu kozo chosa hokokusho. 2. Nippon Indonesia sekitan kyodo tansa Tanjung Enim project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The survey was finished in the final fiscal year (FY 2000) of the Tanjung Enim IV Coal Exploration Project between Japan and Indonesia, and a report was summarized on the preliminary coal mining plan. In the design of the optimum mining area and pit, in terms of 3 cases of coal price of $8, $10, and $12/ton, the pit design was made considering rivers, houses, power transmission lines, etc., and the actual coal yield was asked. In the case of coal price of $8/ton, the actual coal yield in pit was 315 million tons in north block and 171 million tons in south block. In the case of coal price of $10/ton, pits are expandable in north block, but not in south block. For all the pit shapes designed, long-term mining plans were worked out. In each of the cases of coal production amount of 1 million, 3 million and 5 million tons, indicated were secular changes in overburden amount and coal quality because of the difference in mining direction. Further studies were made on the deposition plan, simulation of models of mining heavy machines, coal mine facilities, economical efficiency of coal mines, etc. (NEDO)

  9. Freestyle swimming technique variations using a parachute Variaciones en la técnica de crol durante el nado resistido con paracaídas

    Directory of Open Access Journals (Sweden)

    J.M. García

    2010-09-01

    Full Text Available

    The appearance of new assistance materials like the parachute make it necessary for coaches to know about the impact that such devices have in swimming. To study this theme 16 national and international swimmers between 19 and 24 years old have been selected. The swimmers participated in four tests that consisted in freestyle (crawl stroke swimming for 10 and 45 seconds at maximum intensity, both with and without the parachute. These tests analysed stroke frequency and stroke length. A within-subjects design has been applied and a study of the facts has been made with an AVAR with repeat measures. The results indicate that the stroke frequency decreases (p<0.05 in the parachute swim during the 10 and 45 second tests, compared with the normal swim. It was also observed that the stroke frequency is higher (p<0.01 in the 10 second test than in the 45 second test. The stroke length is higher (p<0.01 in the normal swim test than in the parachute test. With respect to the swim periods of time, the stroke length is higher (p<0.01 in the 45 second test than in the 10 second test. The parachute swim produces important changes in stroke frequency and stroke length in both the 10 and 45 second tests in subjects swimming the freestyle at maximum intensity.
    KEY WORDS: swimming, swim resistance, parachute, crawl, freestyle,. stroke frequency, stroke length.

    La aparición de nuevos materiales auxiliares, como el paracaídas, hace necesario que los entrenadores conozcan las modificaciones que estos producen durante el nado. Para conseguir este objetivo se seleccionaron a 16 nadadores de nivel nacional e internacional comprendidos entre los 19 y 24 años. Éstos realizaron cuatro pruebas que consistieron en nadar a crol durante 10 y 45 segundos a máxima intensidad, utilizando el nado normal (NN y el nado resistido con paracaídas (NRCP. En estas pruebas se analizaron las variables

  10. Efeitos comportamentais e imunológicos da fluoxetina em ratos submetidos ao nado forçado

    Directory of Open Access Journals (Sweden)

    Eduardo Vignoto Fernandes

    Full Text Available No presente trabalho, os efeitos comportamentais e imunomoduladores da fluoxetina foram avaliados num modelo animal de depressão, o nado forçado. Nesse, o comportamento de flutuar é sensível a antidepressivos e é usado como índice de desespero comportamental. Foram utilizados dois grupos experimentais, sendo um grupo controle tratado com salina e outro grupo teste tratado com a fluoxetina, ambos administrados por via intra-peritoneal. Os animais foram tratados três vezes ao dia por 12 dias. Adicionalmente, a resposta imune humoral a uma imunoestimulação (hemácias de carneiro foi avaliada. A fluoxetina provocou aumento no tempo em flutuação, queda na massa corporal e menor produção total de anticorpos. Os resultados indicam uma modulação simultânea do comportamento e do sistema imunológico pela fluoxetina.

  11. Comparación de los efectos del D-004, imipramina y sertralina en el modelo de nado forzado en ratones

    Directory of Open Access Journals (Sweden)

    Daisy Carbajal Quintana

    2012-09-01

    Full Text Available Introducción: La finasterida, inhibidor de la 5 a-reductasa, se emplea en el tratamiento de la hiperplasia prostática benigna, y ocasiona entre sus efectos adversos un aumento de cuadros de depresión. El D-004 es un extracto lipídico extraído a partir del fruto de la palma real (Roystonea regia, inhibe la 5 a-reductasa y previene la hiperplasia prostática benigna, y muestra un efecto antidepresivo moderado en el ensayo de nado forzado y suspensión por la cola. Objetivo: comparar el efecto del D-004 con la imipramina y la sertralina sobre la duración de las conductas de inmovilidad, nado y escalado en el ensayo de nado forzado. Métodos: se distribuyeron los ratones en ocho grupos: control (vehículo, tres tratados con D-004 (100, 250 y 500 mg/kg, dos con sertralina y dos con imipramina (30 y 50 mg/kg respectivamente. Estos se colocaron en un cilindro de cristal que contenía agua a una altura de 6 cm y se cuantificaron las conductas. Resultados: la administración oral de D-004 (100, 250 y 500 mg/kg durante 14 días redujo significativamente el tiempo de inmovilidad con respecto al grupo control (17, 22 y 25 % y aumentó significativamente la conducta de nado en 1,58, 1,68 y 1,74 veces. Este efecto resulta moderado (25 % comparado con las reducciones alcanzadas por la sertralina y la imipramina (³ 60 %. Las dosis mayores (250 y 500 mg/kg ocasionaron incrementos de la conducta de escalado, 2,79 y 3,55 veces superiores a la del grupo control, lo que mostró semejanza con la imipramina, aunque con una menor eficacia. Conclusiones: el D-004 ejerce un moderado efecto antidepresivo, lo que pudiera contribuir al manejo de los pacientes con hiperplasia prostática benigna en los cuales se informa coincidencia de cuadros depresivos.

  12. Antidepressant behavioral effects of duloxetine and fluoxetine in the rat forced swimming test Efeitos antidepressivos da duloxetina e da fluoxetina no teste do nado forçado em ratos

    Directory of Open Access Journals (Sweden)

    Leandro Ciulla

    2007-10-01

    Full Text Available PURPOSE: To compare the effects of the antidepressant drugs duloxetine and fluoxetine on depressive behaviors in rodents. METHODS: Eighteen male Wistar rats were given systemic injections of duloxetine, fluoxetine, or saline prior to a Forced Swimming Test (FST. Immobility and number of stops were measured. RESULTS: Rats given injections of fluoxetine displayed significantly less immobility (p = 0.02 and fewer stops than the control group (p = 0.003. Duloxetine significanlty reduced the number of stops (p = 0.003, but did not effect immobility (p = 0.48. CONCLUSION: Duloxetine and fluoxetine reduced depressive behaviors in the Forced FST. However, our findings suggest that fluoxetine is more effective than duloxetine.OBJETIVO: Comparar o efeito antidepressivo da droga cloridrato de duloxetina com a fluoxetina. MÉTODOS: O teste do nado forçado, teste comportamental que avalia a atividade antidepressiva em ratos, foi utilizado em 18 ratos Wistar, machos adultos, divididos em três grupos iguais: duloxetina, fluoxetina e controle. RESULTADOS: Os dados do teste do nado forçado foram analisados pelo teste One-way ANOVA, Mann Whitney e Kruskall-Wallis.Houve diferença significativa (p = 0,003 entre o número de paradas dos grupos duloxetina e fluoxetina e o grupo controle. CONCLUSÃO: A duloxetina e a fluoxetina tiveram frequência de paradas similares. A fluoxetina mostrou ser mais efetiva que a duloxetina no teste do nado forçado em ratos.

  13. Transtorno do comportamento alimentar em atletas de elite de nado sincronizado Eating disorders in elite synchronized swimmers

    Directory of Open Access Journals (Sweden)

    Talita Adão Perini

    2009-02-01

    Full Text Available OBJETIVOS: O objetivo do presente estudo foi identificar a presença de transtorno do comportamento alimentar (TCA ou síndromes precursoras e o grau de distorção da imagem corporal em atletas de elite de nado sincronizado. Essa modalidade é considerada de risco para desenvolvimento de TCA por valorizar, além de outros aspectos, a leveza e beleza de movimentos que, de certa forma, estão associados a baixa massa corporal. MÉTODOS: Foram avaliadas 27 atletas de nado sincronizado, sendo 19 da categoria juniores (15,6 ± 0,8 anos e oito da categoria de seniores (19,0 ± 1,3 anos que compunham a seleção brasileira na época do estudo (2000. Um grupo de 32 adolescentes não-atletas (15,0 ± 1,6 anos foi usado para comparação com as atletas. Os procedimentos metodológicos adotados foram: aplicação de três instrumentos de auto-relato, validados. 1 EAT-26 - presença de comportamentos alimentares inadequados; 2 BITE - presença de atitudes sugestivas de bulimia nervosa; e 3 BSQ - insatisfação da auto-imagem corporal. RESULTADOS: Embora tanto o grupo de atletas, quanto o de não-atletas tenham apresentado parâmetros antropométricos compatíveis com padrões saudáveis para a idade e sexo, os resultados evidenciam a presença de insatisfação com a auto-imagem corporal e a adoção de práticas patológicas de controle da massa corporal, sobretudo entre atletas da categoria juniores e entre as adolescentes não-atletas. CONCLUSÕES: Os resultados encontrados no presente estudo retratam uma tendência mundial de preocupação com a aparência entre adolescentes capaz de levá-las à adoção de condutas não-saudáveis.OBJECTIVES: The aim of the present study was to identify the Eating Behavior Disorder (EBD or precursory syndromes and the level of distortion of the body image of elite synchronized swimming athletes. This sport modality is considered of risk for development of eating disorders for valuing, among other aspects, the

  14. Efeito do treino com elástico cirúrgico na melhora do desempenho de jovens nadadores na distância de 50 metros na técnica de crol : efeito da utilização de tarefas de treino de velocidade de nado resistido com elástico cirúrgico na melhora do resultado obtido num teste de 50 metros de crol em jovens nadadores

    OpenAIRE

    Rezende, Mônica dos Anjos Costa de

    2010-01-01

    Dissertação de mestrado em Biocinética, apresentada à Faculdade de Ciências do Desporto e Educação Física da Universidade de Coimbra Este estudo consiste na avaliação do efeito de treino com nado resistido, através do uso de um elástico cirúrgico (série 3x4x20” três vezes por semana), durante um período de cinco semanas sobre a força propulsiva e a velocidade de nado numa prova de 50 metros nado de crol. A amostra constou de 22 jovens atletas de dois países, 10 (5 masculino, 16,0 anos ±0,3...

  15. Efeito do destreinamento sobre variáveis cinemáticas relacionadas ao desempenho do nado crawl com diferentes estratégias de respiração

    OpenAIRE

    Pereira, Bernardo Maia Farage

    2012-01-01

    Sabe-se que o destreinamento acarreta em perda das adaptações do sistema cardiorrespiratório e neuromuscular adquiridas com o treinamento físico, inclusive na natação. Apesar de diversos estudos terem investigado o efeito do destreinamento do ponto de vista fisiológico, ainda não foi encontrado na literatura estudos que tenham investigado o efeito do destreinamento em variáveis cinemáticas durante o nado. Sabendo disso esse trabalho foi desenvolvido com objetivo de verificar se há efeito do d...

  16. Surface swimming behavior of the curculionid Ochetina uniformis Pascoe (Erirhininae, Stenopelmini and Ludovix fasciatus (Gyllenhal (Curculioninae, Erodiscini Comportamento de nado superficial exibido pelos Curculionidae Ochetina uniformis Pascoe (Erirhininae, Stenopelmini e Ludovix fasciatus (Gyllenhal (Curculioninae, Erodiscini

    Directory of Open Access Journals (Sweden)

    Wesley Oliveira de Sousa

    2007-03-01

    Full Text Available The swimming behavior exhibited by specimens of L. fasciatus and O. uniformis was analyzed frame-by-frame with video observation recorded with a digital camera, attached to a stereomicroscope. Adults of O. uniformis, an aquatic insect, swim with all three pairs of legs. During the process of swimming the majority of the abdomen and rostrum remain submerged, part of the fore and hind tibiae remain above the surface, while the mid tibiae remain submerged. The mesothoracic legs, during the power-stroke stage, provide the greatest thrust while the metathoracic legs provide the least forward propulsion. The prothoracic legs, extended forward, help to direct the swimming. The semi-aquatic specie L. fasciatus shows the same swimming style as O. uniformis, that is, with movement of all the three pairs of legs; the mesothoracic legs are responsible for the main propulsion. The insect body remains on the water surface during the process of swimming, while the legs remain submerged. Both species complete a swimming cycle in 0.33 and 0.32 seconds, respectively, with an average speed of 1.38 cm/s and a maximum and minimum swimming duration time of 11.15 and 5.05 minutes, respectively, for L. fasciatus. The swimming behavior exhibited by O. uniformis and L. fasciatus corresponds to the style known as a breast strokelike maneuver. This is the first record of this kind of swimming for both species here observed and increases to seven the number of genera of Curculionidae exhibiting this behavior.O comportamento de nado exibido por indivíduos de L. fasciatus e O. uniformis foi analisado quadro a quadro através de imagens obtidas com o auxílio de uma câmera fotográfica digital com opção de vídeo, acoplada a um estereomicroscópio. Foi demonstrado que O. uniformis, espécie aquática, nada com o auxílio dos três pares de pernas. Durante este processo a maior parte do abdome e rostro localizam-se abaixo da superfície da água, parte das t

  17. Research report for fiscal 1998. Research of feasibility of energy supply/demand structure overseas improvement (research of feasibility of more effective energy use for Russian energy consuming industries); 1998 nendo kaigai energy jukyu kozo kodoka jisshi kanosei chosa. Roshia no energy tashohi sangyo ni okeru energy yuko riyo nado jigyo jisshi kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A report is made outlining the economic situation and industrial policies in Russia and the actual state of energy consuming industries (thermoelectric power generation, oil refining, and iron making) in that country. In Russia, energy efficiency is much lower than in advanced countries in the West, and the improvement of energy efficiency is a serious task to solve in the Russian fuel energy department. Cited to explain the poor efficiency are facilities growing antiquated, delay in the introduction of new technologies and instruments, insufficient maintenance, and the weak consciousness of energy saving. Although the electric power circle and energy related departments are conscious of the need of endeavors for improving energy efficiency, yet it is too difficult for corporations themselves to invest heavily in facilities. When Japan implements a model project for saving energy in Russia, it will be greatly contributing to the improvement of energy supply/demand in Russia, to the stabilization of social and economic states in that country, and to the prevention of global warming. (NEDO)

  18. Comparación de los efectos del D-004, imipramina y sertralina en el modelo de nado forzado en ratones Comparative effects of D-004, Imipramine and Sertraline in the forced swimming test in mice

    Directory of Open Access Journals (Sweden)

    Daisy Carbajal Quintana

    2012-09-01

    Full Text Available Introducción: La finasterida, inhibidor de la 5 a-reductasa, se emplea en el tratamiento de la hiperplasia prostática benigna, y ocasiona entre sus efectos adversos un aumento de cuadros de depresión. El D-004 es un extracto lipídico extraído a partir del fruto de la palma real (Roystonea regia, inhibe la 5 a-reductasa y previene la hiperplasia prostática benigna, y muestra un efecto antidepresivo moderado en el ensayo de nado forzado y suspensión por la cola. Objetivo: comparar el efecto del D-004 con la imipramina y la sertralina sobre la duración de las conductas de inmovilidad, nado y escalado en el ensayo de nado forzado. Métodos: se distribuyeron los ratones en ocho grupos: control (vehículo, tres tratados con D-004 (100, 250 y 500 mg/kg, dos con sertralina y dos con imipramina (30 y 50 mg/kg respectivamente. Estos se colocaron en un cilindro de cristal que contenía agua a una altura de 6 cm y se cuantificaron las conductas. Resultados: la administración oral de D-004 (100, 250 y 500 mg/kg durante 14 días redujo significativamente el tiempo de inmovilidad con respecto al grupo control (17, 22 y 25 % y aumentó significativamente la conducta de nado en 1,58, 1,68 y 1,74 veces. Este efecto resulta moderado (25 % comparado con las reducciones alcanzadas por la sertralina y la imipramina (³ 60 %. Las dosis mayores (250 y 500 mg/kg ocasionaron incrementos de la conducta de escalado, 2,79 y 3,55 veces superiores a la del grupo control, lo que mostró semejanza con la imipramina, aunque con una menor eficacia. Conclusiones: el D-004 ejerce un moderado efecto antidepresivo, lo que pudiera contribuir al manejo de los pacientes con hiperplasia prostática benigna en los cuales se informa coincidencia de cuadros depresivos.Introduction: Finasteride is a 5 a-reductase inhibitor to treat benign prostatic hyperplasia (BPH and one of the adverse effects is the increase of depressive symptoms. D-004 is a lipid extract from the real palm

  19. Desempenho e pacing na prova de 200 m nado borboleta: variabilidade e relações dos tempos parciais de 50 m com o tempo final

    Directory of Open Access Journals (Sweden)

    F.A. de Souza Castro

    2017-12-01

    Full Text Available Resumo: Objetivo: Analisar o desempenho e o pacing de prova dos semifinalistas da prova de 200 m nado borboleta do 15.° Campeonato Mundial de Natação da Federação Internacional de Natação (FINA. Método: Os dados foram obtidos da página eletrônica da FINA. Os 32 tempos da etapa semifinal, masculina e feminina, foram divididos em 4 grupos: 8 homens classificados para a final (G1M, 8 homens não classificados (G2M, 8 mulheres classificadas para a final (G1F e as 8 mulheres não classificadas (G2F. A velocidade de nado, para cada parcial de 50 m, foi estimada pelo quociente entre 50 m e o respectivo tempo. Foram calculados os coeficientes de variação de tempo das 4 parciais de 50 m e comparados entre os grupos (ANOVA. Tamanho de efeito foi verificado com d de Cohen. Correlacionou‐se o desempenho (tempo total com o tempo de cada parcial de 50 m (r de Pearson. Resultados: O coeficiente de variação para as parciais de 50 m foi menor nos grupos dos finalistas de ambos os sexos (G1M e G1F e menor para as mulheres. A terceira parcial de 50 m apresentou maior correlação com o desempenho final em ambos os sexos. A velocidade média caiu ao longo da prova em ambos os grupos. Conclusão: O pacing para o melhor desempenho na prova é evitar variações de tempo ao longo dos 200 m nado borboleta e os treinamentos devem ser direcionados ao aprimoramento condicionante dessa parcial (150‐200 m. Resumen: Objetivo: Analizar el desempeño y pacing durante la prueba de semifinalistas de 200 m mariposa del 15.° Campeonato Mundial de Natación de la Federación Internacional de Natación (FINA. Método: Los datos fueron retirados de la página electrónica de la FINA. Los 32 tiempos de la semifinal masculina y femenina fueron divididos en cuatro grupos: ocho varones clasificados para el final de la prueba analizada (G1M, ocho varones no clasificados (G2

  20. Análise dos parâmetros cinemáticos determinantes do desempenho na prova de 200 m nado livre Analysis of the determinant kinematical parameters for performance in the 200-m freestyle swimming event

    Directory of Open Access Journals (Sweden)

    Maria Inês Ferreira

    2012-06-01

    Full Text Available Os objetivos deste estudo foram: i caracterizar o nado submáximo e máximo do ponto de vista cinemático; ii verificar a influência das variáveis cinemáticas na prova máxima de 200 metros crawl. Nove nadadores de elite nacionais realizaram dois testes: um submáximo, descontínuo de intensidade progressiva; outro máximo, que consistiu em uma simulação de uma prova de 200 m crawl. Foram estudados os parâmetros cinemáticos gerais da mecânica da braçada, a duração de cada fase do ciclo gestual, a velocidade do centro de massa e a variação intracíclica da velocidade horizontal. Verificaram-se diferenças cinemáticas significativas da frequência gestual, velocidade de deslocamento do centro de massa, duração total do ciclo gestual, duração da ação subaquática propulsora e da velocidade do centro de massa na fase de recuperação entre os testes. Identificou-se associações significativas entre o teste máximo e algumas variáveis cinemáticas como a velocidade do centro de massa e índice de nado.The main aims of this study were i to perform a kinematic characterization of sub and maximal swimming speed; ii to investigate the associations between the kinematic profiles and the 200 m front crawl style. Nine national level male swimmers performed two speed tests: a submaximal discontinuous speed trial of progressive speed intensity, and a maximal one, simulating a 200 m front crawl style. The stroke general kinematic parameters, the phases duration of the stroke cycle, the velocity of the centre of mass and the intra cyclic variation of the horizontal velocity were herein studied. Significant kinematic differences in relation to stroke rate, horizontal velocity of the centre of mass, total cycle duration, absolute and relative duration of the propulsive sub aquatic action and the velocity of the centre of mass during the arms recovery were compared between the speed tests. Significant correlations between the performance in

  1. Antidepressant behavioral effects of duloxetine and amitriptyline in the rat forced swimming test Efeitos antidepressivos da duloxetina e da amitriptilina no teste do nado forçado em ratos

    Directory of Open Access Journals (Sweden)

    Honório Sampaio Menezes

    2008-10-01

    Full Text Available PURPOSE: To compare the effects of the antidepressant drugs duloxetine and amitriptyline on depressive behaviors in rats. METHODS: Fifteen male Wistar rats were given systemic injections of duloxetine, amitriptyline or saline prior to a Forced Swimming Test (FST. Immobility and number of stops were measured. Data were analyzed by one-way ANOVA and Kruskall-Wallis. RESULTS: Rats given injections of duloxetine displayed fewer stops than the amitriptyline and control group (pOBJETIVO: Comparar o efeito antidepressivo da droga cloridrato de duloxetina com a amitriptilina. MÉTODOS: O teste do nado forçado, teste comportamental que avalia a atividade antidepressiva em ratos, foi utilizado em 15 ratos Wistar, machos adultos, divididos em três grupos iguais: duloxetina, amitriptilina e controle. Os dados foram analisados pelo teste One-way ANOVA e Kruskall-Wallis. RESULTADOS: Houve diferença significativa entre o número de paradas (p <0,05 entre os grupos duloxetina e amitriptilina e o grupo controle. Grupo amitriptilina e controle não apresentaram diferença (p=0,8. CONCLUSÃO: A duloxetina reduziu o comportamento depressivo sendo mais efetiva do que a amitriptilina.

  2. Neonatal treatment with fluoxetine reduces depressive behavior induced by forced swim in adult rats Tratamento neonatal com fluoxetina reduz o comportameto depressivo induzido pelo nado forçado em ratos adultos

    Directory of Open Access Journals (Sweden)

    Cristiano Mendes-da-Silva

    2002-12-01

    Full Text Available Serotonin plays a role at the pathophysiology of depression in humans and in experimental models. The present study investigated the depressive behavior and the weigh evolution in adult rats (60 days treated from the 1st to the 21st postnatal day with fluoxetine, a selective serotonin reuptake inhibitor (10 mg/kg, sc, daily. The depressive behavior was induced by the forced swim test (FST. The animals were submitted to two sessions of FST: 1st session for 15 min and the 2nd session 24h later, for 5 min. During the 2nd session the Latency of the Attempt of Escape (LAE and Behavioral Immobility (BI were appraised. The Fluoxetine group when compared to the Control group, showed an increase in LAE and a decrease in BI. The neonatal administration of fluoxetine reduced the depressive behavior in adult rats, possibly by increase in the brain serotonergic activity. This alteration can be associated to process of neuroadaptation.Estudos em humanos e em modelos experimentais demonstram que a serotonina (5-HT participa da fisiopatologia da depressão. O presente estudo investigou o comportamento depressivo e a evolução ponderal de ratos adultos jovens (60 dias tratados do 1º ao 21º dia pós-natal com fluoxetina, um inibidor seletivo de recaptação da serotonina, (10 mg/kg, sc, diariamente. A depressão experimental foi induzida através do teste de nado forçado (NF. Os animais foram submetidos a duas sessões de NF, a primeira por 15 min e a segunda após 24 h, por 5 min. Durante os 5 min de NF a latência da tentativa de fuga (LTF e o tempo de imobilidade (TI foram avaliados. O grupo tratado com fluoxetina apresentou aumento da LTF e redução do TI comparado ao controle. A administração neonatal de fluoxetina reduziu o comportamento depressivo em ratos adultos, possivelmente em função do aumento da atividade serotoninérgica cerebral. Esta alteração poderá estar relacionada a processos neuroadaptativos.

  3. Estudio preliminar de la expresión proteómica cerebral de la región hipocampal de ratas expuestas a diferentes niveles de estrés inducido por el nado forzado Preliminary study of cerebral proteomics expression of hippocampal region from rats exposed to different stress levels induced by forced swimming

    Directory of Open Access Journals (Sweden)

    Guerrero Nasser

    2012-04-01

    Full Text Available Introducción: en general, los estímulos estresores pueden inducir respuestas adaptativas o mal adaptativas dependiendo, entre otras cosas, de su intensidad y la duración. Sin embargo, no se han llevado a cabo estudios que relacionen cuantitativa y cualitativamente la intensidad de estrés al que es expuesto un animal y la expresión de proteínas del hipocampo. Objetivo: evaluar la expresión diferencial de proteínas hipocampales en ratas Wistar-UIS, expuestas a diferentes niveles de estrés inducido por el nado forzado. Materiales y métodos: se utilizaron 30 ratas Wistar-UIS machos distribuidas aleatoriamente en 3 grupos según el tiempo de exposición al nado forzado como estímulo estresor (0, 5 y 15 minutos. Después de 24 horas se extrajeron los hipocampos dorsales y se realizó electroforesis bidimensional de las proteínas extraídas. A continuación, se llevó a cabo el procesamiento de las imágenes de los geles obtenidos utilizando el software PDQUEST 2D. Aquellas proteínas en las se detectaron intensidades asociadas a los tiempos de exposición al estímulo, se identificaron de manera presuntiva utilizando la base de datos bioinformática Export Protein Analysis System (EXPASY. Resultados: de acuerdo con el análisis proteómico y bioinformático se identificaron 60 proteínas, de las cuales, 38 eran comunes al hipocampo derecho e izquierdo; 13 del hipocampo derecho y 9 del izquierdo. Conclusión: se encontraron diferencias en la expresión de proteínas entre el hipocampo derecho e izquierdo del tipo dosis dependientes decrecientes después de haber sometido a los animales a diferentes niveles de estrés inducido por la prueba de nado forzado. Salud UIS 2012; 44 (1: 17-27Introduction: in general stressful stimuli can induce adaptive maladaptive responses, depending among other things, of their intensity and duration. However, no studies were found in the literature that link quantitatively and qualitatively the intensity of

  4. Optimization of sustaining swimming speed of matrinxã Brycon amazonicus: performance and adaptive aspects Otimização da velocidade de nado sustentado em matrinxã Brycon amazonicus: rendimento e aspectos adaptativos

    Directory of Open Access Journals (Sweden)

    Gustavo Arbeláez-Rojas

    2010-01-01

    ,5 comprimentos corporais - BL por segundo. As melhores velocidades de nadado estiveram entre 1,0 e 1,5 BL s–1, nas quais o crescimento dos peixes foi 20% maior que nas outras. A hemoglobina e as células vermelhas do sangue em 1,5 BL s–1 aumentaram 24% e 18% respectivamente; o hematócrito foi 17 % maior em todos os peixes exercitados; o conteúdo de proteína do músculo branco em 1,0 BL s–1 foi 2% maior; a deposição de lipídio no músculo vermelho em 1,0 BL s–1 foi 22% maior e a retenção de água foi 3% menor. Os níveis de energia bruta aumentaram 10% em todos os peixes exercitados; a retenção de água no fígado foi 6 % menor em 1,0 BL s–1; a composição de lipídio no fígado foi 29% maior do que o controle e 34% maior do que a 1,5 BL s–1; a energia bruta no fígado aumentou em 1.0 BL s–1 comparada com o controle e 2,5 BL s–1. A deposição de lipídio no músculo ventral foi 9% maior em 2,0 BL s–1. Embora alta deposição de lipídio em matrinxã tenha sido obtida em velocidades moderadas de nado, os lipídios podem ser a fonte de combustível principal para manter as exigências metabólicas de matrinxã em exercício. A melhor velocidade de nado para obter o melhor crescimento em matrinxã está entre 1,0 e 1,5 BL s–1.

  5. Structures of bats; Komori no kozo

    Energy Technology Data Exchange (ETDEWEB)

    Natori, M. [Institute of the Space and Astronautical Science,Tokyo (Japan); Kishimoto, N. [The University of Tokyo, Tokyo (Japan)

    1999-12-05

    This paper gives an outline of the structures of bats. Unlike birds, bats have a wing membrane structure. The membrane constituted of the skin is spread between five fingers to form the wing. The wing membrane is seen in the forelimbs and the tail. In the chest and the shoulder, the ligament sheet supports the muscles. The wing membrane is about 0.5mm in thickness, with a fiber net woven through reflecting a tension field in flying. The fiber net is composed of compound materials of elastin and collagen. The shoulder joints consists of the clavicle, scapula and humerus, which is close to human beings. The elbow joints rotate only inside the plane of the wings. The leg joints are hook-shaped, with the tendon sheath provided with ruggedness. The carpus is made up of eight bones and is characterized by the ability of spreading and storing the wings. At the time of storing the wing membrane, the finger joints are stored and, during the flight after the wings are spread, it forms the flapping wing plane. Lightweight and formation of the sturdy front edge are characteristics common to other flying creatures. The spreading and the storing are possible through the direct motion of the hands. The shoulder joints and the carpus of the human beings are closer to those of bats than to those of birds. (NEDO)

  6. Aplicación de volúmenes de nado para las categorías 11 - 12 y 13 -14 años de los atletas de la escuela de natación de Pinar del Río

    Directory of Open Access Journals (Sweden)

    Zaylen Serralta Hernández

    2011-12-01

    Full Text Available La presente investigación es un estudio realizado con los atletas de las categorías 11-12 y 13-14 años de La Escuela de Natación de Pinar de Río, tomando como muestra a todos los alumnos de estas categorías a partir del curso 2007-2008. Se analiza detalladamente los volúmenes de nado propuestos por el Programa de Preparación del Deportista (PPD, donde se aprecia que los atletas de la provincia no logran cumplir lo indicado por el mismo, siendo el inicio tardío en la práctica del deporte, la carencia de piscinas con un funcionamiento estable y las bajas temperaturas en el periodo invernal, los que más afectan el proceso. Provocando esto que no se alcancen resultados satisfactorios y con ello desmotivación y deserción por parte de los alumnos. La aplicación de los nuevos volúmenes inferiores a los PPD nos permitió obtener una mejor progresión y resultados satisfactorios en los eventos que se participa en las distintas competencias.

  7. Efecto del D-004, un extracto del fruto de Roystonea regia y omega-3 en el modelo de nado forzado en ratones Effect of D-004, a fruit extact from Roystonea regia and Omega-3 in a model of forced swimming in mice

    Directory of Open Access Journals (Sweden)

    Daisy Carbajal Quintana

    2010-03-01

    Full Text Available La depresión se encuentra entre las principales causas de morbilidad y mortalidad de la población adulta y su manejo farmacológico incluye, entre otras opciones alternativas, el uso de la medicina complementaria, como es el caso del aceite de pescado rico en ácidos grasos omega-3 (AGw3. El D-004, extracto lipídico de los frutos de la palma real (Roystonea regia que consiste en una mezcla de ácidos grasos, ha mostrado poseer una moderada acción antidepresiva. El objetivo de este trabajo consistió en comparar los efectos del tratamiento oral con D-004, con los AGw3 y con su terapia combinada en el modelo del nado forzado en ratones. Para ello, ratones machos se distribuyeron en 8 grupos: uno control tratado con el vehículo, dos con D-004 (250 y 500 mg/kg , dos con AGw3 (250 y 500 mg/kg, dos con la combinación y uno con imipramina (10 mg/kg i.p.. Todos los tratamientos disminuyeron significativamente el tiempo de inmovilidad con respecto al control, sin diferencias entre dosis similares de los respectivos tratamientos. En conclusión, el D-004, los AGw3 y su terapia combinada resultaron igualmente efectivos en reducir el tiempo de inmovilidad de los ratones, sin manifestarse efectos aditivos o sinérgicos con la administración conjunta de ambas sustancias.Depression is among the major causes of morbidity and mortality of adult population and its pharmacologic management includes among other alternative options, the use of the complementary medicine, e.g. the fish oil rich in Omega-3 fatty acids (AGw3. The D-004, a lipid extract of Real Palm fruits (Roystonea regia consisting of a fatty acid mixture, has a moderate antidepressant action. The aim of present paper was to compare the effects of oral treatment using D-004 with the AGw3 and with its combined therapy in forces swimming in mice. Thus, the male mice were distributed into 8 groups: one as control treated with vehicle, two with D-004 (250 and 500 mg.kg, two with AGw3 (250 and 500

  8. Ne nado obizhatsja na Karzaja / Sven Mikser

    Index Scriptorium Estoniae

    Mikser, Sven, 1973-

    2008-01-01

    Afganistani presidendi Hamid Karzai arvates on liitlasvägede Helmandi provintsis viibimise ajal olukord provintsis halvenenud. Autori arvates on Eesti rahukaitseväed teinud oma tööd Afganistani olukorra stabiliseerimisel hästi, ja seda jätkatakse

  9. Troihh nado ubrat, reshil komissar / Boris Tuch

    Index Scriptorium Estoniae

    Tuch, Boris, 1946-

    2004-01-01

    4. märtsil esilinastus mängufilm "Täna öösel me ei maga" : stsenaristid Kristian Taska, Jaan Tätte : režissöör Ilmar Taska : operaator Istvan Borbas : produtsent Kristian Taska : peaosades Carmen Kass, Peter Franzen; Maria Avdjushko, Priit Võigemast : Taska Productions

  10. Comportamento de variáveis fisiológicas em atletas de nado sincronizado durante uma sessão de treinamento na fase de preparação para as Olimpíadas de Atenas 2004 Comportamiento de variábles fisiológicas en atletas de nado sincronizado durante una sesion de entrenamiento en la fase de preparación para las Olimpíadas de Atenas 2004 Behavior of physiological variables in synchronized swimming athletes during a training session preparing for the Athens 2004 Olympic Games

    Directory of Open Access Journals (Sweden)

    Marina Guimarães Antunes Pazikas

    2005-12-01

    Full Text Available O objetivo do presente estudo foi avaliar o comportamento de variáveis fisiológicas durante uma sessão de treino de nado sincronizado realizada na fase de preparação para as Olimpíadas de Atenas 2004. MATERIAIS E MÉTODOS: A amostra utilizada foi constituída pelo dueto (24 ± 0 anos representante do Brasil em Atenas 2004. A coleta de dados foi realizada durante uma sessão de treinamento com duração de 198 minutos. O treino se iniciou com a parte física, seguida da parte técnica. Para a determinação da glicemia e da concentração de beta-hidroxibutirato foi utilizado o monitor Optium® com suas respectivas tiras. As concentrações de cortisol e das enzimas lactato desidrogenase (LDH e creatina quinase (CK foram determinadas por radioimunoensaio (DPC© e kits comerciais (CELM®, respectivamente. O acompanhamento da freqüência cardíaca (FC foi realizado com o freqüêncimetro Advantage Polar®. RESULTADOS: Foi observada redução (~2% do peso corporal. A glicemia também apresentou queda (~30% em comparação ao valor obtido no início do treino. Em contrapartida, foi observada elevação na concentração de cortisol (salivar 22% e plasmática 29% e de beta-hidroxibutirato (~340%. Não foi observada alteração significativa na concentração plasmática de CK e de LDH. O acompanhamento da FC demonstrou que dos 198 minutos que constituíram a sessão de treino, 36,5 ± 0,7 minutos foram realizados em intensidade leve; 103,5 ± 0,7 minutos em intensidade moderada, 54,0 ± 2,1 minutos em intensidade alta e 4,0 ± 0,0 minutos em intensidade muito alta. CONCLUSÕES: A perda de peso indica que a reposição hídrica não foi adequada. A redução na glicemia e o aumento na concentração de corpos cetônicos e de cortisol reforçam a importância da suplementação de carboidrato durante o treino de longa duração. O comportamento da FC demonstra que a sessão de treinamento foi realizada em uma intensidade moderada, porém com

  11. Proposta de teste incremental baseado na percepção subjetiva de esforço para determinação de limiares metabólicos e parâmetros mecânicos do nado livre Propuesta de un test adicional basado en la percepción subjetiva del esfuerzo para determinar los límites metabólicos y los parámetros mecánicos del nado libre Incremental test proposal based on the rating of perceived exertion to determine metabolic thresholds and mechanical parameters of free style

    Directory of Open Access Journals (Sweden)

    Manoel Carlos Spiguel Lima

    2006-10-01

    Full Text Available A percepção subjetiva de esforço (PSE é determinada de forma não invasiva e utilizada juntamente com a resposta lactacidêmica como indicadores de intensidade durante teste incremental. Em campo, especialmente na natação, há dificuldades nas coletas sanguíneas; por isso, utilizam-se protocolos alternativos para estimar o limiar anaeróbio. Assim, os objetivos do estudo foram: prescrever um teste incremental baseado na PSE (Borg 6-20 visando estimar os limiares metabólicos determinados por métodos lactacidêmicos [ajuste bi-segmentado (V LL, concentração fixa-3,5mM (V3,5mM e distância máxima (V Dmáx]; relacionar a PSE atribuída em cada estágio com a freqüência cardíaca (FC e com parâmetros mecânicos de nado [freqüência (FB e amplitude de braçada (AB], analisar a utilização da escala 6-20 na regularidade do incremento das velocidades no teste e correlacionar os limiares metabólicos com a velocidade crítica (VC. Para isso, 12 nadadores (16,4 ± 1,3 anos realizaram dois esforços máximos (200 e 400m; os dados foram utilizados para determinar a VC, velocidade de 400m (V400m e a freqüência crítica de braçada (FCb; e um teste incremental com intensidade inicial baseada na PSE, respectivamente, 9, 11, 13, 15 e 17; sendo monitorados em todos os estágios a FC, lactacidêmia e os tempos de quatro ciclos de braçadas e das distâncias de 20m (parte central da piscina e 50m. Posteriormente, foram calculadas as velocidades dos estágios, FB, AB, V LL, V3,5mM e V Dmáx. Utilizaram-se ANOVA e correlação de Pearson para análise dos resultados. Não foram encontradas diferenças entre VC, V Dmáx e V LL, porém a V3,5mM foi inferior às demais velocidades (P La Percepción Subjetiva del Esfuerzo (PSE es determinada de forma no invasiva y utilizada juntamente con la respuesta lactacidémica como indicadores de intensidad durante un test de incremento. En campo, especialmente en la natación, hay dificultades en las colectas

  12. Imaging of salt structure; Gan`enso kozo no imaging

    Energy Technology Data Exchange (ETDEWEB)

    Akama, K; Saeki, T [Japan National Corp., Tokyo (Japan). Technology Research Center; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan)

    1996-10-01

    Due to the improvement of algorithm and the advancement of calculation performance, the imaging by depth migration before stacking is being put into practice from the viewpoint of both calculation cost and accuracy. A lot of imaging examples have been already reported from the survey areas with complicated velocity structures, such as the North Sea and the Gulf of Mexico. Effectiveness of the method has been confirmed. For imaging techniques in Japan National Oil Corporation and Japan Petroleum Exploration Co., Ltd., high-speed depth migration before stacking and high efficiency velocity structure estimation technique have been investigated. This paper describes necessary care to be taken when using depth focusing analysis (DFA) for correcting a velocity model, as an interim stage of case study. The results of depth migration before stacking using dip moveout (DMO) velocity were further inferior to the section obtained by the migration after tracking. Tendency of velocity errors was distinctly deviated with the variation of depth and horizontal position. It was not suitable for modifying the velocity model using DFA. 4 refs., 4 figs.

  13. Magnetic structure of volcanic neck; Kazangankei no jiki kozo

    Energy Technology Data Exchange (ETDEWEB)

    Makino, M; Okuma, S; Morijiri, R; Nakatsuka, T [Geological Survey of Japan, Tsukuba (Japan)

    1997-05-27

    This paper describes the summary and result of magnetic exploration on the Kabutoyama volcano in the city of Nishinomiya, Hyogo Prefecture, Japan. It also states the interpretation and discussion on magnetic anomaly in the volcanic conduit of the mountain by using a three-dimensional magnetic structure model. Terrain surface magnetic exploration for the Kabutoyama volcano was performed by using six traverse lines each in different azimuths with the triangulation point at the summit as the basic point and by using a proton magnetometer. The exploration results of the six traverse lines around the Kabutoyama volcano may be generalized as follows: magnetic anomaly in the vicinity of the summit is moderate with little change, but it increases to 500 nT to 2,500 nT in the vicinity of the distances of 150 m to 200 m; a peak is formed with a width of a few tens of meters; and the magnetic anomaly showed a trend of rapidly decreasing at outer sides of the peak. The results of the magnetic exploration and the magnetization intensity measurement leads to a belief that such a magnetic anomalous band of an annular form would exist corresponding to the boundary or its vicinity of andesite and granite, and the Rokko granite having magnetization intensity as small as can be neglected would be distributed at outer sides of the boundary. The result of the three-dimensional magnetic structure model calculation, which assumes the internal structure of the magnetic structure to be non-uniformly magnetized, reproduced the magnetic anomaly patterns well as compared with the observation results. 1 ref., 5 figs.

  14. Analysis of automotive tire construction. Jidosha tire no kozo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Ishihara, K. (Toyo Tire and Rubber Co. Ltd., Osaka (Japan))

    1993-06-15

    This paper introduces features and trends of analyzing performance and construction of automotive tires. Tires are demanded of high durability, high motion performance, good comfort performance for vibration and noise, and low fuel consumption performance. A feature of analyzing the construction is to execute a modelling assuming that a tire has air-rigid flexible structure and rubber materials show hyperelastic behavior, hypothesizing a strain energy density function. In addition, a tire is highly incompressible. Visco elasticity and anti-friction performance are also important points. Rubber and cord layers have elastic characteristic of three-dimensional perpendicular anisotropy as well as non-linearity with which characteristics change according to transformation. A structural analysis must cover from static analysis to steady dynamic analysis, non-steady dynamic analysis, and eigenvalue analysis. Thermal analysis of tires simulates phenomena by combining dynamical analysis with thermal analysis. Super-computers have now come to be used for formulating equilibrium equations using finite element methods, developing finite elements, and performing heat or visco elasticity analysis and applied analysis. 35 refs., 3 figs.

  15. Aircraft fatigue failures and duties of structural reliability analysis. Kokuki kozo no hiro hakai to kozo shinraisei kaiseki no yakuwari

    Energy Technology Data Exchange (ETDEWEB)

    Fujiwara, G [Japan Airlines Co. Ltd., Tokyo (Japan)

    1992-10-05

    The use of a commercial jet transport airplane over its life of 20 years has been increasing because of intestified competition after cancellation of the regulations. It is necessary that users of the airplane adopt such a positive way as they themselves maintain safety of their airplanes rather than they wait for feedback or technical instructions from manufacturers. This paper outlines the points at issue regarding the problem of fatigue strength which is fundamental to the safety problem, explaining by various examples that the fatigue strength problem includes phenomena of which theoretical elucidation has not been obtained. Consequently, some points to be paid attention to are cited. For instance, in the analysis of reliability in case of determining the period for initial inspection (safety life), reliability should be 95-99% which have been advised by Boeing and others, even if confidence level is 95% as usual In case of considering a fleet number in the reliability analysis, the fleet number should be reflected by grouping significant in fatigue analysis. 30 refs., 10 figs., 1 tab.

  16. Application of VSP to geological investigation; P ha oyobi S ha VSP wo mochiita shinso chishitsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    Kinugasa, Y [Geological Survey of Japan, Tsukuba (Japan); Feng, S; Sugiyama, T; Ishikawa, K [Chuoh Kaihatsu Corp., Tokyo (Japan)

    1997-05-27

    Discussed in this paper are the P-wave and S-wave zero-offset VSPs carried out utilizing boreholes located in Nada Ward, Kobe City, and Hokudan-cho, Hyogo Prefecture, as part of the deep layer boring survey following Hanshin Earthquake Disaster. This effort aims at the elucidation of P-wave and S-wave velocity structures, high-precision identification of data obtained by the surface reflection method, and collection of basic data for active faults investigation in the future. Among the velocity structures obtained for various layers, the S-wave velocity structures in particular agree with the stratigraphy excellently and may be utilized in seismic analyses to be conducted in the future. Reflection from geological boundaries is received with precision, providing accurate information about correlation between reflection and geological cross sections. The records will be useful in formulating plans for reflection surveys for instance of the boundary between the Osaka group and Kobe group. Generally speaking, reflection coefficients are large when the reflection is from a boundary where difference is great in elastic wave impedance (mainly difference in velocity). In the case of the boundary between the Kobe group and granite in Awaji Island, however, no strong reflection is found despite the great difference in velocity. This is attributed to the complicated, sharp inclination of the basement rock and to its weathering. 4 refs., 8 figs.

  17. Increased dialogue between NADOs and academics – challenges and possibilities

    DEFF Research Database (Denmark)

    Gleaves, John; Christiansen, Ask Vest

    2015-01-01

    More than just repositories of knowledge, academics have an obligation to also forge new paths of discovery. As the boundary between what we know and what we still do not know expands, academics are not required to ask “what applied value does this discovery have.” Galileo’s curiosity in the time...... it took a chandelier to swing, measured only by his heartbeat, was not intended to help create modern timepieces, though it did through the discovery of the tautochrone nature of a pendulum. It was simple curiosity driven by unanswered questions and the human desire to know. We should pursue truth...

  18. Vallo Reimaa : "Statussu regionalnogo tsentra nado sootvetstvovat i za nego nado borotsja" / Vallo Reimaa ; interv. Aleksei Starkov

    Index Scriptorium Estoniae

    Reimaa, Vallo

    2007-01-01

    Regionaalminister vastab küsimustele, mis puudutavad Jõhvi gümnaasiumi juurdeehituse rajamist ja riigilt selleks toetuse taotlemist, linnade konkurentsi regionaalkeskuse staatuse saamiseks, Ida-Viru maavanema kandidaate. Minister on seisukohal, et tuleb toetada kõike, mis tugevdab Jõhvi kui regionaalkeskuse staatust, ja regionaalne gümnaasium on just selline objekt

  19. Subsurface geology by shallow seismic reflection survey and microgravity survey in Kobe area; Senso hanshaho danseiha tansa oyobi seimitsu juryoku tansa ni yoru Kobe chiiki no chika chishitsu

    Energy Technology Data Exchange (ETDEWEB)

    Endo, H; Makino, M; Murata, Y; Watanabe, S [Geological Survey of Japan, Tsukuba (Japan)

    1996-05-01

    This paper reports discussions on subsurface structure of the Kobe area by means of microgravity survey. A Bouguer anomaly distribution graph was obtained (which is close to a near straight line) by measuring the gravity at measurement points with an interval of about 25 m along a traverse line (with a total length of about 1.7 km) in an approximately NNW-SSE direction crossing the downtown of the city of Kobe. Viewing the residuals to a straight line linking the values at both ends of the traverse line revealed that the gradient in the Bouguer anomaly distribution changes as if it is bent at a point near the center of the traverse line as a boundary. Deriving the residuals from fine changes seen in a distribution graph for the residuals made clear that this residual distribution has two discontinuous points. The paper indicates that the bending point in the former case corresponds to a reverse fault in a base bed of a flat land as compared with the result of model calculation on the base structure and gravity distribution. The discontinuous points in the latter case agree with positions of fault distribution derived by a reflection elastic wave survey. 6 refs., 4 figs.

  20. Change in pore structure of coals by activation with KOH; KOH fukatsushita sekitan no saiko kozo

    Energy Technology Data Exchange (ETDEWEB)

    Maruyama, K.; Yoshizawa, N.; Ishikawa, E.; Kobayashi, M.; Toda, Y.; Yamada, Y.; Shiraishi, M. [National Institute for Resources and Environment, Tsukuba (Japan)

    1996-10-28

    Three typical Japanese coals of non-coking coal, coking coal and anthracite were heat-treated with KOH, and change in their pore structure was examined by absorption of N2, X-ray diffraction and TEM observation. In addition, the relation between a coal rank and pore structure was also studied by absorption experiment of N2. In experiment, the mixture of coal and KOH in a nickel holder was heat-treated in N2 gas flow at heating rate of 2{degree}C/min, and held at a fixed temperature for one hour. To clarify the pore structure, N2 absorption isotherms were measured at -196{degree}C under nearly 76cmHg using a commercially available full-automatic absorption measurement equipment. Based on the X-ray diffraction and TEM observation results on activated coals, the relation between the N2 absorption and pore structure was studied. The results are summarized as follows: (1) The yield and absorption ability of coals increase with a coal rank, (2) The specific surface area of coals reaches its peak at 800{degree}C in activation temperature regardless of a coal rank, and (3) The activation behavior of coals is dependent on a coal rank. 5 refs., 7 figs., 1 tab.

  1. Dissipative structure of mechanically stimulated reaction; Kikaiteki reiki hanno ni okeru san`itsu kozo

    Energy Technology Data Exchange (ETDEWEB)

    Hida, M. [Okayama Univ., Okayama (Japan). Faculty of Engineering

    1994-12-20

    Recently various studies have been conducted concerning the state changes of materials obtained through mechanical alloying (MA) or mechano-chemical (MC) processing. What is noticeable is the quasi-steady state of almost all the materials obtained through various processes including MA and MC, and that the super cooling, supersaturating and high residue distortion realized under unbalanced conditions have not been clarified. In other words, the tracing capability to the external binding conditions is low. In this report, the appearance of the high temperature phase and high pressure phase obtained through MA or MC processing, the forming of amorphous, the mesomerism of the amorphous materials, the interesting phenomena generated by combination between the mechanical disturbance and chemical reactions were discussed with concrete examples, and a steady dissipative organization theory was approached from the viewpoint of dissipative structure development which is equal to the forming process of the quasi-steady phase. 34 refs., 2 figs.

  2. Structure and reaction of electrolytic solution. Denkaishitsu yoeki no kozo to hanno

    Energy Technology Data Exchange (ETDEWEB)

    Otaki, H. (Okazaki National Research Inst., Aichi (Japan))

    1990-07-05

    An electrolytic solution has been recognized as an ion transporting system since the oldest time in the history of electrochemistry, and the chemistry related thereto forms the most basic field of electrochemistry. In this article, the progress of chemistry concerning electrolytic solutions since M. Faraday is briefly stated, and in view of very scanty structural knowledge available on other solutions in comparison with the structure of water on which extensive studies have been made, the respective structures of such non-aqueous solutions as the mixed solvent of N,N-dimethylformamide (DMF)-acetonitrile (AN) and the mixed solvent of dimethylsulfoxide (DMSO)-2,2,2-triphloroethanol (TFE) are studied. In addition, concerning the solvation when ions exist in such a non-aqueous solvent mixed system, the selective solvation of Cu {sup 2+} ions in the DMF-AN and Cu {sup 2+} as well as Cl {sup {minus}} ions in the DMSO-TFE is respectively explained, and the solvent effect, etc. of Cu {sup 2+} ions and Cl {sup {minus}} ions on the complex forming reaction are discussed. 17 refs., 8 figs., 2 tabs.

  3. Mathematical structure of ocean container transport systems; Kaiyo container yuso system no suriteki kozo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Shinkai, A [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Chikushi, Y [Nippon Telegraph and Telephone Corp., Tokyo (Japan)

    1997-10-01

    Mathematical structure of a vessel arrangement program was discussed in order to learn roles of container ships in ocean transport systems among China, NIES/ASEAN countries and Japan. Formulation is possible on a mathematical handling method for sailing route connection diagrams between ports, a transport network to indicate container movements, a service network to indicate sailing routes, and a network generalizing them. This paper describes an analysis made on the container transport system between Japan and China, taken as an example. Four ports were selected each from Japan and China, and the statistical database for fiscals 1996 and 1994 was utilized to set models for: (a) the liner network system with transshipment at the port of Shanghai and (b) the cruising route system going through the ports of Yokohama, Nagoya and Kobe. A hypothesis was set that a consortium (coordinated ship allocation) can be implemented ideally and completely. The transport network (a) is lower by 10% in total cost than the transport network (b), resulting in 1.6 times greater productivity. Actual service network is closer to the network (b), but the system can be utilized for discussing guidelines on vessel arrangement programs with which shipping companies pursue better management efficiency under a condition that the consortium can be formed. 10 refs., 6 figs., 2 tabs.

  4. Today and tomorrow on optimization of structural systems. Kozo system saitekika no genjo to shorai

    Energy Technology Data Exchange (ETDEWEB)

    1992-07-20

    It has been 30 years since a conception structurally optimized design method'' was advocated as a new structural design system which links three factors; mathematical programming, a finite element method, and computers. This paper summarizes the current states in the optimizing technologies in Japan and views over their future, with reference mainly to the two symposiums held in the past as an activity of the subcommittee for structural system optimization in the Japan Society of Civil Engineers. The summary covers the following matters: Optimizing algorithms for structural designs, fuzzy theories, practical use of expert systems and AI, maintenance and management systems for structures, vibration control, shock resistant designs, inverse problems and structure identifying problems, and designs of underground and off-shore structures. For instance, examples of bridge designs include a minimum mass design on a pedestrians' bridge incorporating vibration sensitivities into restricting conditions, comparisons of economics in suspension bridges using a multi-stage determination method, and many others. Optimizing technologies are believed to advance greatly in the future and be used as a very routine design tool. 145 refs., 1 fig., 3 tabs.

  5. Fault structure analysis by means of large deformation simulator; Daihenkei simulator ni yoru danso kozo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Murakami, Y.; Shi, B. [Geological Survey of Japan, Tsukuba (Japan); Matsushima, J. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

    1997-05-27

    Large deformation of the crust is generated by relatively large displacement of the mediums on both sides along a fault. In the conventional finite element method, faults are dealt with by special elements which are called joint elements, but joint elements, elements microscopic in width, generate numerical instability if large shear displacement is given. Therefore, by introducing the master slave (MO) method used for contact analysis in the metal processing field, developed was a large deformation simulator for analyzing diastrophism including large displacement along the fault. Analysis examples were shown in case the upper basement and lower basement were relatively dislocated with the fault as a boundary. The bottom surface and right end boundary of the lower basement are fixed boundaries. The left end boundary of the lower basement is fixed, and to the left end boundary of the upper basement, the horizontal speed, 3{times}10{sup -7}m/s, was given. In accordance with the horizontal movement of the upper basement, the boundary surface largely deformed. Stress is almost at right angles at the boundary surface. As to the analysis of faults by the MO method, it has been used for a single simple fault, but should be spread to lots of faults in the future. 13 refs., 2 figs.

  6. Magnetic structure of Akita-Yakeyama volcano; Akita Yakeyama chiiki no jikiteki kozo

    Energy Technology Data Exchange (ETDEWEB)

    Okuma, S [Geological Survey of Japan, Tsukuba (Japan)

    1996-10-01

    Akita-Yakeyama is a Quaternary volcano located in the north-western part of the Sengan geothermal area. Geothermal resource surveys have been performed from the middle of the 1970s in the Sengan geothermal area, and the Sumikawa geothermal power plant started its operation in 1995. By the analysis, the magnetic basement depth became lower in the north of Yakeyama body. However, the distribution including low magnetic anomaly in the south of Yakeyama body could not be explained only by a simple magnetic structure model. In this study, the magnetic anomaly in this area was analyzed in detail, and a construction of the magnetic structure model was intended by taking borehole data into account. The low magnetic intensity zone with low amplitude agreed well with the geothermal alteration zone. The high magnetic intensity zone and the low magnetic intensity zone corresponded with the distributions of volcanic rocks magnetized normally and reversely, respectively. Kakkonda and Matsukawa geothermal power plants were located in the distinct low magnetic intensity zones. There was a low magnetic intensity zone with long wave length over the whole Sengan geothermal area. A high magnetic intensity zone was observed in the northern foot of this area. From the magnetic measurements of borehole sample rocks, this was found to correspond with the newly formed granite body. 9 refs., 4 figs.

  7. Surface structures and optical functions of living things. Seibutsu no hyomen kozo to kogaku kino

    Energy Technology Data Exchange (ETDEWEB)

    Kumazawa, K.; Takimoto, J.; Tanaka, S.; Tabata, H. (Nissan Motor Co. Ltd., Tokyo (Japan))

    1993-12-24

    This paper describes the following matters as one example of structural coloring of non-motional nature on the coloring mechanism in wings of Morpho sulkouskyi butterfly: The structure of scales on butterfly wings may be modelled into such a structure of a right angle frame of reference having a cyclic arrangement (with an interval of 0.7 [mu]m) of a zigzagged protrusion in the 'x' direction called a ridge (with a height of 1.8 [mu]m and a width of 0.54 [mu]m, the shape not changing in the 'y' direction), and having a plurality of protrusions of a ridge form called lamella in the 'z' (height) direction. A simple multi-layered thin film model was assumed that has lamella layers and air layers laminated alternately in the 'z' direction. The model was used to calculate reflection spectra on vertically incident light based on thickness and refractive index of material layers determined by a structural analysis of the scales. The result was considerably close to the reflection spectra of scales measured by using a microscopic spectrophotometer when the number of layers is set to six. The paper describes briefly examples of motility structural coloring (skin cells of rainbow color in tropical fish). 7 refs., 12 figs.

  8. Imaging of salt structure. 2; Gan`enso kozo no imaging. 2

    Energy Technology Data Exchange (ETDEWEB)

    Akama, K; Saeki, T [Japan National Oil Corp., Tokyo (Japan). Technology Research Center; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan)

    1997-05-27

    With respect to a velocity model structuring method using depth focusing analysis (DFA) as a depth image processing technology used for elastic wave exploration, its practicability was discussed. First, synthetic data were used to extract problems in the DFA. The problems were extracted by using a model with constant velocity as an initial model, deciding on the sequential structures from the higher order, and estimating velocity and depth of each layer by using a model fitting type method. In its application to field data, characteristic records include those for rock salt beds distributed in a sheet form and the folding structure associated with the growth thereof, as acquired in offshore seismic exploration carried out in the eastern part of Gulf of Mexico. The conclusion is that the DFA is a method that can derive a velocity model with required accuracy by using a minimum number of repetition even against relatively complex structures. Particularly, the quick convergence from the initial model with a constant velocity until a certain accuracy is reached is a noteworthy advantage. 3 refs., 6 figs.

  9. High resolution resistivity profiling using STRATAGEM system; Stratagem wo mochiita kobunkainohi teiko kozo tansarei

    Energy Technology Data Exchange (ETDEWEB)

    Yamane, K; Inoue, J; Takasugi, S [GERD Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Inazaki, T [Public Works Research Institute, Tsukuba (Japan)

    1997-05-27

    A tensor type CSMT method (STRATAGEM) was introduced for the purpose of investigating shallow subsurface, and a field test has been carried out thereon. This system consists of a transmission section, and a sensor section and a data acquisition and processing section to observe waveforms in a responsive electromagnetic field. The signal source is a semi-circular air loop with a radius of a little smaller than 2 m. The measuring points were selected at locations about 200 m apart from the signal source to measure two electric field components and two magnetic field components by using sensors installed on the ground surface. The field test was performed at the Yutsubo area in Oita Prefecture, Japan. The electric field dipole is basically 5 m long, while S and E lines are 10 m long. The measurement frequency ranges from 96 kHz to 1000 kHz. The measurement time was about five minutes, and the whole measurement work including apparatus set-up and withdrawal was completed in about 15 minutes to minimize interference with the field which is a meadow. The field test result revealed that resistivity profile in shallow subsurface can be obtained much more easily than with the conventional CSMT method. 2 refs., 10 figs.

  10. Countermeasures for increasing sequence continuous casting; Renchu kinosei taikabutsu zaishitsu, kozo kaizen ni yoru renrenchusu kojosaku

    Energy Technology Data Exchange (ETDEWEB)

    Tsuda, Masato; Shinagawa, Hiroaki; Kamada, Ryuji; Hiraga, Yutaka; Hara, Takayasu [Nippon Steel Corp., Tokyo (Japan)

    1999-06-01

    In the second continuous casting line of Kure Iron Works, Nisshin Steel Co., Ltd. improvement of the continuous casting counts per tundish was attempted for a target of max. 20. The results are as follows: (1) Non-SiO{sub 2} conversion of material for the long nozzle immersed part: About 20% improvement of durability compared with a conventional material to clear 0.059 mm/min of the targeted erosion speed when 20 CCC/TD is realized, (2) Durability improvement of SN plate: About 20% durability improvement was attained compared with a conventional material by the adoption of a non-SiO{sub 2} material, (3) Erosion resistance improvement of the immersed nozzle slug line part: Castable period was extended to 1 ch life improvement by increasing zirconia content, (4) Rise of stopper full open position: The rise of the full open position produced less variation of melt level than the conventional structure without increase of the SN opening, enabling plugging prevention between the stopper head and the upper nozzle which was an objective of this improvement, (5) Structure improvement of the upper nozzle: This improvement successfully prevented leaks from damage of the casting stop nozzle metal case and enabled casting under low gas flow even in TD nozzle plugging. These improvements gave a possibility to achieve max. 20 CCC/TD. (NEDO)

  11. Coherent structure in geostrophic flow under density stratification; Mippei seisoka ni aru chikoryu no soshiki kozo

    Energy Technology Data Exchange (ETDEWEB)

    Tsujimura, S.; Iida, O.; Nagano, Y. [Nagoya Institute of Technology, Nagoya (Japan)

    1998-10-25

    The coherent structure and relevant heat transport in geostrophic flows under various density stratification has been studied by using both direct numerical simulation and rapid distortion theory. It is found that in a neutrally stratified flow under system rotation, the temperature fluctuations become very close to two-dimensional and their variation is very small in the direction parallel to the axis of rotation. Under the stable stratification, the velocity and temperature fluctuations tend to oscillate with the Brunt-Vaisala frequency. Under the unstable stratification, on the other hand, vortex columns are formed in the direction parallel to the axis of rotation. However, the generation of the elongated vortex columns cannot be predicted by the rapid distortion theory. The non-linear term is required to generate these characteristic vortex columns. 11 refs., 18 figs., 1 tab.

  12. Leading research of smart structural system; Chiteki kozo system no sendo kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The technology trend was surveyed to clarify the themes of smart structural system towards its R and D. The smart structural system is a structural system which incorporates functions of perception, judgment and learning by integrating functions, structures and information, to ensure the structural soundness at real time and control the active-adaptive of shapes. The final goal of it is to make materials and structures similar to organic systems. It has a self-repair function which can detect the generation and propagation of cracks and prevent the destruction positively with conducting self-diagnosis. High performance, high efficiency and energy saving are expected by combining the conversion of design concept into destruction control and the regulation of vibration, noise and shape. Especially, it is effective for the safety of aerospace systems, earthquake disaster measures, and extension of machine life. This report describes the background, purpose, R and D activities in Japan and foreign countries, and basic development themes. In addition, it arranges the needs of various industrial fields systematically, and proposes a concrete concept. Furthermore, the effects expected by the application of smart structural systems and the outline of international technical cooperation are presented. 110 refs., 164 figs., 19 tabs.

  13. Fatigue of cable anchorage of large cable stayed bridge; Daikibo shachokyo cable teichaku kozo no hiro

    Energy Technology Data Exchange (ETDEWEB)

    Endo, T.; Matsumoto, T. [Honshu-Shikoku Bridge Authority, Tokyo (Japan); Tsukahara, H. [Yokogawa Bridge Corp., Tokyo (Japan); Miki, C. [Tokyo Institute of Technology, Tokyo (Japan)

    1995-10-21

    Design considerations such as design schemes, the assemblage and welding of steel plates, and safety for fatigue of welded connections have to be taken for the cable anchorages of the steel cable stayed bridges. In this study, two full scale models, which have different shape of box anchorages welded to the web of the main girder, were made to investigate fatigue characteristics as well as assemblage of plate and gelding details. Finite element analyses for both test models and actual bridges here carried out to compare stress distribution. It was confirmed that the assemblage and welding of both types of box anchorage were attainable kith required quality and accuracy. According to the fatigue test, fatigue cracks originated from the weldings of the bearing plate to which the load from cable socket applied directly were caused by out-of-plane bending of the bearing plate. It was proved that the slight modifications of the details around the bearing plate resulted in sufficient fatigue strength in both types of anchorage. 1 ref., 23 figs., 2 tabs.

  14. Hybrid structure in civil engineering construction.; Doboku bun`ya ni okeru fukugo kozo.

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, S. [Yokohama National Univ. (Japan). Faculty of Engineering

    1995-03-30

    The structure of steel-concrete hybrid structure which is recently attracting attention is outlined quoting some examples. The effects of steel-concrete hybrid structure are classified according to the characteristics. The Normandie Bridge completed in January this year near the mouth of the Seine River in France is a cable stayed bridge with the world largest span, and it has a hybrid structure of ingeniously combined steel and concrete. The Dole Bridge in France is a hybrid bridge with 7 continuous spans having steel corrugated sheets in the web. Hybrid structure has come to be applied to many structures other than the superstructure works of bridges. The substructures of bridges are applied to immersed tunnels, and the usefulness has come to be recognized widely. The features of hybrid structure can contribute well to the reinforcement of existing structures. In addition, adoption of hybrid structure has been studied as the best method for repairing and reinforcing structures damaged by earthquakes. 8 refs., 6 figs., 1 tab.

  15. A influência de palmares e parachute na coordenação dos nados

    OpenAIRE

    Thiago Telles

    2012-01-01

    Resumo: A natação é uma modalidade esportiva que, ao longo dos anos, sofreu modificações, atingindo um alto nível de exigência, o que é refletido nas sessões de treinamentos e nas pesquisas sobre a modalidade. Sendo assim, para otimizar o deslocamento nos nadadores pode-se otimizar a força propulsora. Para isso, pode-se utilizar palmares e parachute. Os palmares tem como função promover o aumento artificial da área da mão, desta maneira, aumenta-se a área frontal da mão do sujeito em contato ...

  16. Vladimir Panov : obvinenija nado dokazõvat / Vladimir Panov ; interv. Jana Toom

    Index Scriptorium Estoniae

    Panov, Vladimir, 1941-

    2008-01-01

    Pistisevõtmises süüdistatud Tallinna endine abilinnapea Vladimir Panov vastab küsimustele, mis puudutavad viieaastast kohtuprotsessi ning Äripäeva ja meedia suhtumist talle esitatud süüdistusse. Kommenteerivad: Tarmu Tammerk, Andrus Saar, Edgar Savisaar

  17. "Estoniju v JeS zashtshishtshat ne nado!" / Signe Ratso ; interv. Eteri Kekelidze

    Index Scriptorium Estoniae

    Ratso, Signe, 1960-

    2004-01-01

    Majandus- ja kommunikatsiooniministeeriumi asekantsleri Signe Ratso sõnul ei too Eesti liitumine Euroopa Liiduga mingeid ootamatusi, Eesti ja EL muutuvad üheks majandusruumiks koos sellest tulenevate tagajärgedega. Tabel: Import kolmandatest riikidest 2003. a. 11 kuu jooksul

  18. 77 FR 42465 - Special Local Regulations, Cruce a Nado Internacional, Ponce Harbor; Ponce, PR

    Science.gov (United States)

    2012-07-19

    ... effect on the human environment. This proposed rule involves special local regulations issued in.... Dated: June 7, 2012. D.W. Pearson, Captain, U.S. Coast Guard, Captain of the Port San Juan. [FR Doc...

  19. Industry brief letter; Kasupikaioki sekiyu koku kaihatsu sekiyu shigen kaihatsu nado sannyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-02-01

    4 companies of Petroleum Resources Development, Indonesia Petroleum, Teikoku Petroleum an Itochu Petroleum Development will sign petroleum exploration and development contract in petroleum mining property offshore of Caspian Sea with Azerbaijan National Petroleum Company, Sokar Company. In another mining property, Mitsui group reached conclusion with Sokar Company in mining right. Resource development competition between existing international petroleum majors and Japanese petroleum companies around Caspian Sea may be further intensified. (translated by NEDO)

  20. Fjodor Berman : "Nado umet terjat dengi" / Fjodor Berman ; interv. Liana Turpakova

    Index Scriptorium Estoniae

    Berman, Fjodor, 1951-

    2006-01-01

    BLRT Grupp ühendab 61 firmat kuues riigis, aktsionärid on aastate jooksul kogu teenitud raha suunanud kontserni arengusse. BLRT Grupi arengust, probleemidest kvalifitseeritud tööjõuga, majandus- ja kommunikatsiooniministeeriumi suhtumisest. Juhatuse esimehe Fjodor Bermani karjäärist Eestis, puhkusest ja vaba aja veetmisest, perekonnast

  1. Samozvantsev nam ne nado, komandirom budu ja / Maksim Shmeljov, Aleksandr Tshaplõgin, Leivi Sher

    Index Scriptorium Estoniae

    Shmeljov, Maksim

    2007-01-01

    Kas Konstitutsioonipartei nimekirjas parlamendivalimistel kandideeriv Dmitri Linter ja tema kaaslased võivad kasutada liikumise Notshnoi dozor brändi ND omakasupüüdlikel eesmärkidel, küsivad autorid

  2. Geological structure of Osaka basin and characteristic distributions of structural damage caused by earthquake; Osaka bonchi kozo to shingai tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Nakagawa, K; Shiono, K; Inoue, N; Senda, S [Osaka City University, Osaka (JP. Faculty of Science); Ryoki, K [Osaka Polytechnic Collage, Osaka (Japan); Shichi, R [Nagoya University, Nagoya (Japan). Faculty of Science

    1996-05-01

    The paper investigates relations between the damage caused by the Hyogo-ken Nanbu earthquake and the deep underground structures. A characteristic of the earthquake damage distribution is that the damage concentrated near faults. Most of the damages were seen on the side of faults` relatively falling rather than right above the faults and of their slightly slanting to the seaside. Distribution like this seems to be closely related to underground structures. Therefore, a distribution map of the depth of basement granite in Osaka sedimentary basin was drawn, referring to the data on basement rock depth obtained from the distribution map of gravity anomaly and the result of the survey using the air gun reflection method. Moreover, cubic underground structures were determined by 3-D gravity analysis. The result was concluded as follows: when observing the M7 zone of the low land, in particular, where the damage was great from an aspect of gravity anomaly, the basement rock below the zone declined near the cliff toward the sea, which indicates a great possibility of its being a fault. There is a high possibility that the zone suffered mostly from the damage caused by focusing by refraction and total reflection of seismic wave rays. 3 refs., 8 figs.

  3. Velocity structure of Nojima-fault by VSP method; VSP ho ni yoru Nojima danso no sokudo kozo

    Energy Technology Data Exchange (ETDEWEB)

    Kuwahara, Y; Ito, H; Kiguchi, T; Miyazaki, T [Geological Survey of Japan, Tsukuba (Japan)

    1996-05-01

    In order to investigate in detail structures of the fractured fault band, the VSP tests were conducted using a 750m deep borehole penetrating the Nojima fault in Awaji Island. The borehole penetrates the fault clay band at a depth of 624m in the Hirabayashi area. The offset VSP survey, conducted by the aid of hydrophone through the naked borehole, detects many characteristic phenomena resulting from the fault fracture. Largely fractured lithofacies are found by the core observation at a depth in a range from 557 to 673m. P-waves propagate at 4.6 and 5.1km/s above and below the fractured band, respectively. The fractured band is subdivided into 2 sections, both being of low speed of 4.5 and 3.1km/s. The X1 and X2 phases resulting from the fault fracture are also observed, above and below the fractured band. The causes for these wave phases are now under investigation. 4 figs.

  4. Structural study of synthetic polymers by MALDI-TOFMS; MALDI-TOFMS ni yoru gosei kobunshi no kozo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Noguchi, K.; Hirayama, K. [Ajinomoto Co. Inc., Tokyo (Japan)

    1998-08-01

    As observation results on the time-dependent change in the ring-opening reaction of novolac epoxy resin with acetic acid by MALDI-TOFMS, the epoxy ring was opened with reaction time, the hydroxy group formed by the ring-opening reaction was acetylated, those components were measured. In the case of the FABMS/MS observation of materials and the reaction products, the estimation structure could be confirmed from the measured results of MALDI-TOFMS. In the polymerization of bisphenol A epoxy resin with N, N`-dimethylethylenediamine, it was observed by MALDI-TOFMS that many kinds of polymers with high molecular weight were formed with an increase of reaction time. In this case, the LSIMS/MS observation of materials and the reaction products was carried out, the estimation structure could be confirmed from the measured results of MALDI-TOFMS. 19 refs., 8 figs.

  5. Change of unit skeletons during an artificial coalification; Jinko sekitanka katei ni okeru tan`i kokkaku kozo no henka

    Energy Technology Data Exchange (ETDEWEB)

    Sugimoto, Y.; Miki, Y.; Hayamizu, K. [National Institute of Materials and Chemical Research, Tsukuba (Japan); Okada, K. [Coal Mining Research Center, Tokyo (Japan); Suzuki, Y. [Geological Survey of Japan, Tsukuba (Japan)

    1996-10-28

    In order to obtain knowledge about formation and growth of condensed ring structure in a coalification process, discussions were given on product skeleton structure by using hydrogenation and hydrocracking of heated cellulose. In underwater heating of cellulose, reaction of dehydration has occurred at 200{degree}C or lower, that of decarbonation at 250{degree}C or higher, and that of demethanizing at 300{degree}C, resulting in production of a dark-brown coal-like substance. The substance has lower H/C value and higher O/C value than coal. As the underwater heating temperature rises, the hydrogenation reactivity of the heated substance decreases, and so does the ratio of conversion into toluene solubles. These phenomena are related to strength of cross-linking bond between unit skeleton structures. A substance heated at an underwater heating temperature of 200{degree}C turns toluene-soluble almost completely even during the hydrogenation reaction (350{degree}C for 2 hours), but the soluble product decreases at underwater heating temperatures of 250 and 300{degree}C. However, soluble product of more than 90% was obtained when hydrocracking (at 425{degree}C for one hour) was performed. The toluene-soluble product in the heated substance is only 50% when the underwater heating temperature reaches 350{degree}C even if the hydrocracking is carried out. 3 refs., 5 figs.

  6. Studies of structure change of iron sulfates and its catalysis; Ryusantetsukei shokubai no kozo henka to sono shokubai sayo

    Energy Technology Data Exchange (ETDEWEB)

    Ogata, E.; Horie, K. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering; Nishijima, A. [National Institute of Materials and Chemical Research, Tsukuba (Japan)

    1996-10-28

    Since a huge amount of coal containing inorganic ash is treated for the commercial hydroliquefaction process, cheap catalysts widely distributing on the earth with large reserves are desired rather than expensive catalysts. This paper describes the effects of addition of sulfur on the catalysis of iron sulfates during the hydroconversion of 1-methylnaphthalene (1-MN). Reactions of 1-MN were conducted at the same charging amount of iron in the reaction system. Sulfur was directly added in the reaction system using ferrous sulfate (FeSO4) as precursor. Consequently, it was found that FeSO4 provides lower but similar catalytic activity to the synthetic pyrite catalyst prepared through the complex processes with the precise control. Thus, it was revealed that high performance pyrrhotite (Fe(1-x)S) catalyst can be prepared for the hydrogenation of aromatic-rings by adding solid sulfur into the reaction system using commercial reagent, FeSO4 as a precursor of the catalyst. 9 figs.

  7. Coal Liquefaction characteristics and chemical structure of product oil; Sekitan ekika hanno tokusei to seiseibutsu no kagaku kozo

    Energy Technology Data Exchange (ETDEWEB)

    Endo, H.; Sato, M.; Chiba, T.; Hattori, H. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology; Sasaki, M. [Hokkaido National Industrial Research Institute, Sapporo (Japan)

    1996-10-28

    Through the hydrogenolysis of Wandoan coal and Tanito Harum coal which are used for the NEDOL process, differences of liquefaction characteristics between them were found. The purpose of this study is to grasp these differences as differences of chemical structures of oil fractions. The compound type analysis was conducted for oil fractions obtained at varied reaction temperature for varied reaction time. Coal liquefaction characteristics of these coals were discussed by relating oil yields and chemical structures. For Tanito Harum coal, yields of gas and oil were considered to be lower than those for Wandoan coal, which reflected that the contents of partially hydrogenated hydroaromatics in oil fraction from the former were lower than those from the latter, and that the remarkable change of composition did not occur with the progress of the reaction. For both the coals, the remarkable changes in the average molecular weight of oil fraction were not observed with the progress of the reaction. While, the content of methane gradually increased with the progress of the reaction, which suggested that oil was gradually dealkylated. 5 figs.

  8. Report on the FY 1999 basic research on intelligent structure; 1999 nendo kozo chinoka no kiso kenkyu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A concept of a system is constructed in which a series of the flow from the construction of structures to the shape and control in structural phase, repair, and dismantlement is made effective and controllable by giving a function of intelligent structure to structural systems in aerospace/architecture/civil engineering fields. For it, fundamental technologies required for the systems were extracted for construction of the technology system. Further, in relation to the intelligent machinery system including the control method, manipulation, and communication of the structure under the micro-gravity environment required for this system, the basic experiment was conducted at the ground gravity-free experimental center to acquire the effective data. As to the base technology, three fields were studied of the intelligent machinery system including the behavior/control of materials and structure, intelligent robot, and communication. In the experiment on micro-gravity environment, experiments were carried out on the behavior of micro-gravity rover for small planetary probe, inter-satellite group communication, capture of trouble-satellite, development of inflatable structure, and hopping robot. The valuable data were obtained. (NEDO)

  9. Structure of non-equilibrium seeded plasma excited with microwave; Micro ha reiki hiheiko seed plasma no kozo

    Energy Technology Data Exchange (ETDEWEB)

    Miyakawa, M.; Murakami, T.; Suekane, T.; Okuno, Y.; Kabashima, S. [Tokyo Institute of Technology, Tokyo (Japan)

    1996-10-20

    Structure of non-equilibrium cesium seeded argon plasma excited with microwave power is simulated numerically. The plasmas produced at suitable microwave powers are found to consist of three regimes, that is, the region limited by charged particle loss toward the wall, the full seed ionization and the diffusion limited regions. The fully ionized seed plasma is produced within the skin-depth determined by the electrical conductivity of the plasma, and the thickness of the fully ionized seed plasma depends on the seed fractions gas pressure and microwave power. 15 refs., 6 figs.

  10. Geometrical relaxation of excitations in one-dimensional conjugated polymers; Giichijigen kyoeki kobunshi reiki jotai no shusa kozo kanwa

    Energy Technology Data Exchange (ETDEWEB)

    Yoshizawa, M. [Tohoku University, Sendai (Japan). Faculty of Engineering

    1995-12-15

    Large ultrafast optical nonlinearities in conjugated polymers have attracted much attention because of possible applications to nonlinear optical devices. One-dimensional systems such as conjugated polymers have localized excited states with geometrical relaxation. In this study, photoexcited states in polydiacetylene has been investigated by femtosecond Raman gain spectroscopy with 300-fs resolution. A new photoinduced Raman peak with lifetime of 1.5 ps has been observed at 1200cm{sup -1} for the first time. This peak indicates acetylene-like structure of the main chain relaxes to butatriene-like structure due to the formation of self-trapped exciting with the geometrical relaxation. The formation and decay kinetics of the Raman signals is consistent with the relaxation processes of exciting observed by femtosecond absorption spectroscopy. 8 refs., 5 figs.

  11. Adaptation of topology optimization on truck-structure; Kinshitsukaho ni yoru iso saitekika shuho no truck kozo eno tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Tachibana, H; Kojima, A; Chiba, S [Mitsubishi Motors Corp., Tokyo (Japan)

    1997-10-01

    An optimization using the homogenization method has been applied to a truck-structure on the concept design stage. A truck-structure is grouped into 3 classes (thin plate structure , thick plate structure and solid structure), then example, effectiveness and method for the application for the purpose of weight reduction , high rigidity and high eigen-frequency are introduced. 3 refs., 24 figs., 1 tab.

  12. Structure analysis of ultra-thin films. STM/AFM. Chousumaku no kozo kaiseki. STM/AFM

    Energy Technology Data Exchange (ETDEWEB)

    Nozoe, H; Yumura, M [National Institute of Materials and Chemical Research, Tsukuba (Japan)

    1994-03-30

    Fullerene (C60) and carbon nanotubes are expected as new carbon structures. This article describes the observation results of C60 and carbon nanotubes by means of STM (scanning tunnel microscope). The STM images of C60 thin films are illustrated, which have been obtained by annealing at 290 centigrade. It was confirmed that C60 monomolecular thin films are formed which conform to the substrate and have high regularity. The step height of C60 monomolecular thin films coincided with the step height of Cu (111) plane, which suggested that the step of films is reflected in that of Cu substrate. For the STM images under bias voltages, various images of C60 with three-fold axis of symmetry were observed. On the other hand, from STM observation of carbon nanotubes with diameter of about 30 nm which were separated and purified from the cathode deposits during the preparation process of C60, it was found that they have concentric multilayer structure. 18 refs., 7 figs.

  13. Structural analyses of very large semi-submersibles in waves; Choogata hansensuishiki futai no harochu kozo oto kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Iijima, K.; Yoshida, K.; Suzuki, H. [The University of Tokyo, Tokyo (Japan)

    1997-08-01

    An analysis method in which the technique of a vehicle obtained when a three-dimensional singular point distribution method and Kagemoto`s mutual interaction theory are combined was expanded for the fluid area was proposed as the structural analysis of very large semi-submersibles in waves. A partial structure method is used for the structure. In a fluid area, the number of unknown quantities appearing in a final expression could be largely reduced by introducing the new concept of a group body. In this process, both hydro-elasticity and hydrodynamic mutual interaction are considered. As a result, floating bodies that could not be previously calculated can be modeled as a three-dimensional frame structure and the response analysis in waves can be carried out without damaging the accuracy. The calculation result is used as the input data required for analyzing the structural fatigue locally during structural design of very large semi-submersibles in the 3,000 (m) class. This study can present a series of procedures between the response analysis of very large floating bodies in waves and the structural design. 11 refs., 14 figs., 1 tab.

  14. Structural changes in deashed coals induced by heat treatment; Kanetsu shori ni yoru dakkaitan no kozo henka

    Energy Technology Data Exchange (ETDEWEB)

    Sugano, M.; Sekita, M.; Muramatsu, Y.; Mashimo, K.; Wainai, T. [Nihon University, Tokyo (Japan). College of Science and Technology

    1996-10-28

    Change in structures of 3 kinds of coals with different coal ranks and their deashed coals was studied by heat treatment below 200{degree}C. In experiment, crushed Adaro, Taiheiyo and Huaibei coals below 200mesh and their deashed coals were used as specimens. The coal and deashed coal specimens dried in vacuum at 110{degree}C for 3 hours were filled into an autoclave, and the heat-treated coal specimens were prepared by holding them under initial nitrogen pressure of 2kg/cm{sup 2} at a fixed temperature for 30min. Extraction using pyridine as solvent, volumetric swelling using methanol or benzene as solvent, and measurement of the amount of carboxyl and phenolic hydroxyl functional groups were conducted for these coal specimens. The experimental results are as follows. Huaibei coal has developed aromatic ring structure, and its structure is hardly affected by heat treatment. The oxygen containing functional groups decrease by heat treatment over 100{degree}C in Adaro coal and 150{degree}C in Taiheiyo coal, and PS, MQ and BQ also decrease due to aggregation between molecules. 5 refs., 2 figs.

  15. Study on spontaneous potential exploration considering resistivity structures; Hiteiko kozo wo koryoshita shizen den`iho tansa

    Energy Technology Data Exchange (ETDEWEB)

    Sato, H; Sakurai, K; Shimada, H [OYO Corp., Tokyo (Japan)

    1996-10-01

    Spontaneous potential (SP) was measured on the known traverse line of resistivity structure crossing Hanaori fault in Ohara area, Kyoto city to observe change in SP around the fault and to examine the possibility of fault position exploration. The supposed causes of generation of SP are as follows: the existence of sulfide mineral deposit including polarized minerals, underground fluid flow, and the existence of stratum including chemical compositions from hot springs. The SP method estimates underground structures based on measured surface potential distributions using DC component under anomaly of SP. FEM modeling clarified that a fault fracture zone is one of the causes of generation of SP, by considering SP measurement and resistivity structure strongly affecting observed SP. Consequently, combination of SP measurement with resistivity structure exploration allows a reliable fault estimation method. Under the assumption that anomaly of SP is caused by polarization around fault, the horizontal dipole model based on polarization of current source dipole along fault can well explain the measured data. 2 refs., 6 figs.

  16. Three-dimensional analysis of the magnetic structure in Hokkaido, Japan; Hokkaido no sanjigen jiki kozo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Makino, M [Geological Survey of Japan, Tsukuba (Japan)

    1996-10-01

    The magnetic structure in Hokkaido was quantitatively analyzed by the magnetic anomaly distribution. This paper describes its characteristics. Detection of structural boundaries and 3-D analysis of double-layer structure were conducted for the regional magnetic data in a region with about 500 km square. There was not so large difference in patterns of magnetic anomaly distribution between the case that the direction of magnetization was set at 45{degree} to the west during the geomagnetic conversion according to Segawa and Oshima and the case that it was set as same as the current geomagnetic direction. The method of Blakely and Simpson was useful to detect the boundaries of magnetic structures. The structural boundaries obtained were more linear than the iso-magnetic contour lines. A new method has been conceived in which the approximation of 3-D magnetic structure analysis can be deduced, and the irregularity of magnetic basement can be determined by the repeated calculation. In practice, this method was applied to the magnetic data in the whole Hokkaido. The calculation was stably converged. It was found that the magnetic structure obtained in the Kamuikotan/Ishikari-Kitakami magnetic belt exhibited a fault structure having steep slopes accompanied by the basin structure in the western boundaries. 19 refs., 6 figs.

  17. Resistivity structures imaging using time-domain electromagnetic data; TDEM ho ni yoru chika hiteiko kozo no imaging

    Energy Technology Data Exchange (ETDEWEB)

    Noguchi, K [Waseda University, Tokyo (Japan). School of Science and Engineering; Endo, M [Waseda University, Tokyo (Japan)

    1996-10-01

    The kernel function for transient vertical magnetic dipole was defined for semi-infinite uniform medium, and the 1-D imaging algorithm by TDEM (time-domain electromagnetic) method was developed for underground resistivity structure. Electromagnetic migration method directly images sectional resistivity profiles from the data observed by frequency-domain MT method, and determines underground resistivity profiles by integral equation of MT field using the concept of return travel time in reflection seismic exploration. The method reported in this paper is also one of the EM migration methods. The imaging algorithm of 2-D resistivity structure was developed by correcting 1-D imaging in consideration of the effect of 2-D anomaly on 1-D imaging (the resistivity of anomaly can be obtained from the resistivity contrast between anomaly and medium). The conventional methods require enormous forward computation, while this method can obtain underground resistivity structure in extremely short computation time, resulting in superior practicability. 12 refs., 7 figs.

  18. Deep sedimentary structure model beneath the Osaka plain; Osaka heiya ni okeru shinbu chika kozo no model ka

    Energy Technology Data Exchange (ETDEWEB)

    Miyakoshi, K; Kagawa, T; Echigo, T [Osaka Soil Test, Osaka (Japan)

    1997-05-27

    Restructuring was carried out on a sedimentary basin structure model of the Osaka plain including Osaka Bay by using newly obtained underground structural data. After the Hygoken-nanbu Earthquake of 1995, a large number of underground structure investigations have been performed in Osaka Bay and urban areas of Kobe and Osaka. However, very few surveys have been done in areas peripheral to Osaka Prefecture, such as the Ikoma area. Therefore, an attempt has been made to increase the number of measuring points to acquire underground structural data of these areas. Estimation of basic rock depths has utilized the dominant cycles in H/V spectra obtained from micro vibration survey, and good correlation of the base rock depths derived by a refraction exploration and a deep-bed boring investigation. With regard to bed division and P- and S- wave velocities in sedimentary beds in the Osaka sedimentary basin, an underground structure model was prepared, which was divided into four beds according to the refraction exploration and the micro vibration investigation. Data obtained by using this model agreed well with depth data acquired from physical exploration and other types of investigations. However, no good agreement was recognized in the data for such areas where the basic depth changes abruptly as the Rokko fault and the Osaka bay fault. 6 refs., 8 figs., 2 tabs.

  19. Structure of poly (. beta. -alanine) polymerized in the solid state. Koso jugo shita. beta. -alanine no kozo

    Energy Technology Data Exchange (ETDEWEB)

    Sakabe, Hiroshi; Nakamura, Hiroyoshi; Kimura, Hirokazu; Konishi, Takashi [Kyoto Inst. of Tech., Kyoto (Japan). Faculty of Textile Science

    1989-12-05

    The structure of poly({beta}-alanine) polymerized in the solid state was studied. This polymerization was carried out on a single crystal of {beta}-alanine at 170 centigrade for 40 h in an evacuated tube. The crystal structure of the polymer was assigned to I-type crystal of Nylon 3. The polymer chains were oriented vertical to the crystal side and different to monomer crystal orientation. This may be caused by the molecular layer slipping along the cleavage plane of monomer crystal. A scanning electron microscope(SEM) showed the band structure of hundreds nm width of same orientation, but X ray showed only unoriented rings, so that they are estimated to be the structure of fine fibril like assembly or necklace like continuous chain structure of grains. Near the surface, whiskers which were thought to be oligomer of low degree of polymerization, were observed. The SEM of end view of the etched surface did not show the laminated structure but showed the network structure of about 1 mu-m which is thought to be fibril precursor. 12 refs., 10 figs.

  20. Evaluation on lifetime risk in reinforced concrete structure; RC kozo no lifetime risk no hyoka ni kansuru kisoteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, M. [Public Works Research Institute, Tsukuba (Japan); Adachi, H. [Taisei Corp., Tokyo (Japan); Akakura, Y. [Ministry of Transport, Tokyo (Japan); Ibayashi, K.; Ozaka, Y. [Tohoku Gakuin Univ., Sendai (Japan)

    1996-02-15

    To evaluate the risk during longevity of reinforced concrete structure subjected to earthquake motions, called lifetime risk, damage and safety were estimated by means of the earthquake risk analysis and earthquake response analysis. For the earthquake risk analysis, historical earthquake data with relatively low accuracy were efficiently taken into account, to determine the annual mean generation probability against the earthquake motion strength in ten main cities. A new damage index with load hysteresis was defined as an anti-earthquake evaluation index where accumulative damage is taken into consideration. Assuming that the damage transits from `certain state` to `certain state` every time the earthquake motion generates at the noticeable place, damage transition matrix expressing transition probability was calculated by using the results of earthquake risk analysis and the accumulative damage index. The lifetime risk was calculated from the damage transition matrix and the earthquake motion generation probability, to evaluate the safety. 21 refs., 10 figs., 8 tabs.

  1. Development of simulator for studying formation process of crustal structure. 1; Chikaku kozo keisei simulator no kaihatsu. 1

    Energy Technology Data Exchange (ETDEWEB)

    Matsushima, J. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering; Murakami, Y.; Okubo, Y.; Matsubayashi, O.; Tanaka, A.; Nakajima, Y.; Morijiri, R. [Geological Survey of Japan, Tsukuba (Japan); Rokugawa, S. [The University of Tokyo, Tokyo (Japan)

    1997-05-27

    The purpose of this study is to combine seismic activity and volcanic activity by reproducing the formation process of the crustal structure from a physical viewpoint or developing as its extension a numerical simulator which can predict the future. The phenomenon to which attention is especially paid at present is a relation between the dynamic process and the thermal process in the domain including the crust or the upper mantle. Namely, to elucidate the formation process of the crust structure, diastrophism also including seismic activity, igneous activity, etc., it is important to evaluate effects of the behavior of heat supplied from the deep on the dynamic process. In the finite element method, it is not easy to make the effect of gravity reflect to the calculation for boundary conditions. Accordingly, it is general to pay attention to stress difference, considering that stress by gravity is in proportion to static rock pressure stress. Further, to realize interaction between the thermal process and the dynamic process, effects of thermal stress are expressed combining the heat conducting analysis and the plastic flow analysis. 3 refs., 7 figs.

  2. Georesistivity structure in the central part of North-Eastern Japan Arc; Tohoku chiho chubu chiiki no denki dendodo kozo

    Energy Technology Data Exchange (ETDEWEB)

    Fujinawa, Y. [National Research Institute for Disaster Prevention, Tsukuba (Japan); Kawakami, N. [GERD Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Ueshima, M. [The University of Tokyo, Tokyo (Japan). Earthquake Research Institute; Honkura, Y. [Tokyo Institute of Technology, Tokyo (Japan)

    1998-03-13

    MT measurement of transects was made in the central part of North-Eastern Japan Arc to clarify tectonics of subduction zones. 1-D, 2-D and 3-D resistivity structures are observed in surface layers, and zones shallower and deeper than a Conrad surface, respectively. A main structure direction is S-N or NNE-SSW. Ishinomaki-Chokai tectonic line and low- resistivity zones due to Quaternary volcanos (Naruko, Onikobe) exist in a backbone range region. Resistivity is 100{Omega}{center_dot}m or less by Bostick Inversion except Mesozoic and Palaeozoic layers in the southern Kitakami mountainous region, resulting in a good agreement with previous results in a north transect. Resistivity is several {Omega}{center_dot}m and depth is several km around Shinjo basin and in surface layers of Kitakami River region. The backbone range region shows complex resistivity structures because of volcanic activity and wide-area hot water activity. High-resistivity layers correspond to stable Mesozoic and Palaeozoic land layers. Seismic velocity increases in the low-resistivity zone. Earthquake generally occurs at the boundary between resistivity structures. 68 refs., 9 figs., 2 tabs.

  3. Deep geological strucure of a volcano verified by seismic wave. Jishinha de mita kazan no shinbu kozo

    Energy Technology Data Exchange (ETDEWEB)

    Hasegawa, A. (Tohoku University, Sendai (Japan). Faculty of Science)

    1991-09-01

    Three dimensional structure of seismic wave velocity for the crest and upper mantle under the North East Japan is determined by the seismic tomography which is prepared by the natural earthquakes confirmed by the observation network for micro earthquakes, indicating that the low velocity region exists just under the corresponding volcano to the upper mantle. Further, the following contents can be verified: Any micro earthquakes which are verified by the above observation network and occur at the depth of 25-40km show the lower generation rate less than 1% and the low dominant frequency compared with the conventional inland earthquake(lower limit of depth is 15km) in the same region and occur around volcanos. The existence of the remarkable reflection surface for S wave which is found at the depth of 10-20km seems to be caused by the melting mass. The above mentioned low velocity region is estimated to correspond to the lifting region of high temperature magma, micro earthquakes of low frequency to the magma activity around that magma and the reflection surface for S wave to the part of the magma. 8 refs., 4 figs.

  4. Study on the structural characteristics of extradosed concrete bridges; Ekusutoradozudo kyo no kozo tokusei ni kansuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Oka, Y. [Japan Highway Public Corp., Tokyo (Japan); Kasuga, A. [Sumitomo Construction Co. Ltd., Tokyo (Japan); Yamazaki, J. [Nihon Univ., Tokyo (Japan). Coll. of Science and Engineering

    1997-03-31

    Parameters are analyzed to provide data for deciding, in the planning and designing stages, whether a cable stayed bridge or an extradosed bridge should be adopted. Comparative investigation of the vibration properties of both types of bridges is also referred to. The result of the study on the structural properties of the cable stayed road bridge and the extradosed road bridge is introduced. Based on the concept of the extradosed bridge, designers are now able to select without restraint the after load sharing rate of the diagonal members. Parameter analysis of a diagonal member reinforced 3-span continuous beam is performed. By introducing indices showing the load sharing rate of the diagonal member, the cable stayed bridge can be distinguished logically from the extradosed bridge in designing. It is found important that the height of the main tower is set to approximately 10% the length of the center span for the construction of the extradosed bridge. The vibration properties of the cable stayed bridge and the extradosed bridge of the same scale are compared. 7 refs., 18 figs., 6 tabs.

  5. Consideration on the dynamic behavior and the structural design of large scale floating structure. 2nd Report. Stability of elastic structure and design of elastic response; Choogata futai no kozo kyodo oyobi kozo sekkei ni kansuru kosatsu. 2. Dansei henkei wo koryoshita fukugensei oyobi kozo oto no sekkei

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, H.; Yoshida, K. [The University of Tokyo, Tokyo (Japan)

    1996-12-31

    A policy of improving a very large floating body was planned based on its dynamic characteristics, and a proposal was made thereon. Furthermore, discussions were given on stability that considers effect of elastic deformation required when a structure is mounted on a floating body. With respect to a structural design of a very large floating body in which elastic response is governing, and upon modeling the very large floating body into an aeolotropic plate on an elastic supporting floor, it was shown that the existing range of natural vibration speed in the elastic response is in higher range than the natural vibration speed of heave. It was also indicated that the peak height of response to waves in resonance is inversely proportional to wave frequency, and furthermore, degree of flowing in of vibration energy during the resonance is determined by an inner product of spatial vibration patterns of wave force and the excited mode shape. A proposal was made on a floating body improved of excessive response in the floating body edges by changing the characteristics of the floating body edges. In addition, discussions were given on stability that considers elastic deformation of a floating body that becomes necessary when a structure, such as a building, is built on a very large floating body. 9 refs., 9 figs., 3 tabs.

  6. Consideration on the dynamic behavior and the structural design of large scale floating structure. 2nd Report. Stability of elastic structure and design of elastic response; Choogata futai no kozo kyodo oyobi kozo sekkei ni kansuru kosatsu. 2. Dansei henkei wo koryoshita fukugensei oyobi kozo oto no sekkei

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, H; Yoshida, K [The University of Tokyo, Tokyo (Japan)

    1997-12-31

    A policy of improving a very large floating body was planned based on its dynamic characteristics, and a proposal was made thereon. Furthermore, discussions were given on stability that considers effect of elastic deformation required when a structure is mounted on a floating body. With respect to a structural design of a very large floating body in which elastic response is governing, and upon modeling the very large floating body into an aeolotropic plate on an elastic supporting floor, it was shown that the existing range of natural vibration speed in the elastic response is in higher range than the natural vibration speed of heave. It was also indicated that the peak height of response to waves in resonance is inversely proportional to wave frequency, and furthermore, degree of flowing in of vibration energy during the resonance is determined by an inner product of spatial vibration patterns of wave force and the excited mode shape. A proposal was made on a floating body improved of excessive response in the floating body edges by changing the characteristics of the floating body edges. In addition, discussions were given on stability that considers elastic deformation of a floating body that becomes necessary when a structure, such as a building, is built on a very large floating body. 9 refs., 9 figs., 3 tabs.

  7. Processing of the reflection seismic data which were acquired in the continental shelf off the north-west Australia; Australia hokusei tairikudana chiiki ni oite shutokusareta hanshaho chishitsu tansa data no shori ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Amano, H [Japan National Oil Corp., Tokyo (Japan)

    1996-05-01

    Reflection exploration of earthquakes was conducted in the continental shelf off the north-west Australia, and a report is made concerning the processing of the acquired data. A GI gun was used as the vibration source, and a wave quite similar to a pulse was generated. Hydrophones were arranged with group intervals of 12.5m, and high-resolution field data were acquired. An analog low cut filter was used to suppress the large-amplitude swell noise attributable to sea conditions. A digital filter was designed for the purpose of eliminating coherent noises from other survey ships. At the ultimate stage the f-k filter was applied to each of the shot records, and the effectiveness was verified. The traverse line was as long as 6700km and therefore the design window was set relatively long at 2.0-4.0s in the residual static correction phase. It was found that this setup is effective in improving the continuity of the reflection surface. 5 figs., 1 tab.

  8. Investigation of geothermal development and promotion for fiscal 1997. Investigation report on geological/alteration zone (No. B-5 Musadake area); 1997 nendo chinetsu kaihatsu sokushin chosa. Chishitsu henshitsutai chosa hokokusho (No.B-5 Musadake chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This investigation was intended to clarify the possibility of existence of geothermal reservoir layer by elucidating the underground structure and thermal source forming the geothermal system around Musadake, in the area extending over Nakashibetu-cho and Shibetu-cho, Shibetu district, Hokkaido, and further by grasping the distribution and properties of the geothermal alteration zone. The geothermal system of the subject area seems to be governed by Musadake - Mt. Shitabanupuri fault, its incidental bent zone, and the graben extending to the southeast side. The thermal source is presumably a magma reservoir that evolved Musa volcano. The depth hot water is presumed to exist in the underground depth around Mt. Imora; and it seems that the thermal conduction and volcanic ejecta are caused by a chain of volcano-related magma reservoirs around Musadake, the thermal source presumably. The depth hot water is estimated to be not less than 250 degrees C and a high Cl concentration. Within the graben, mudstones are distributed such as Kawakita layer and Yokoushigawa geological layer. Moreover, it is possible that an impermeable layer due to alteration is spread. (NEDO)

  9. Outline of tectonic geology of the cenozoic Pacific volcanic zone concerned with geothermal areas in the central America; Chubei ni okeru chinetsutai wo tomonau shinseidai Taiheiyo kazantai no chishitsu gaisetsu

    Energy Technology Data Exchange (ETDEWEB)

    Yamasaki, T [Kyushu University, Fukuoka (Japan); Matsumoto, Y [Yamaguchi University, Yamaguchi (Japan)

    1994-09-16

    For the purpose of technological cooperation on geothermal development, investigations and discussions have been given on the geological background in the geothermal areas in Central America where the Pacific volcanic zone stretches. The geology in Central America is divided largely into three geological structures distributed in a band form in the east-west direction. Among these structure, the Pacific Volcanic Province is a Caenozoic volcanic area ranging along the Pacific Ocean coast in the south-east direction, where young and active Quarternary volcanoes are lined straight over a distance of 1,400 km. The geological structure is such that continuously traceable rift valley or pit structure agrees with the array of volcanoes. The long and wide rift valley that governs this volcanic activity forms the base of the geothermal areas dotted in the above structure. Guatemala had been proceeding with a 24-MW power plant plan in Zunil, the most important point, but the construction has been delayed because of a landslide that caused impediment to the productive wells. The plant completion is now scheduled for 1995. El Salvador is the most advanced country in geothermal power generation, which operates three plants in the Ahuachapa geothermal area, with the output reaching 95 MW. The geothermal condition per production well is 110 tons per hour at 250{degree}C. Nicaragua had been successful in generating power of 70 KW with two plants in Momtombo by 1989. 22 refs., 8 figs., 4 tabs.

  10. FY 2000 survey on technical trends. Survey of technical trends on materials for heightening of performance for power generation facility use; 2000 nendo gijutsu doko nado chosa. Hatsuden shisetsuyo koseinoka zairyo ni kakawaru gijutsu doko nado chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As to high performance/high function plastic materials used in power generation facilities, technical trends were surveyed on the recycle situation and recycle R and D to study the subjects to be solved. For wire covering materials, vinyl chloride, polyethylene, rubber, etc. are used, and the recycle of resin has not been advanced. Concerning the generation of waste plastic, the existence of a lot of plastics different in characteristics makes the recycle difficult. As to the use of waste plastic as resource, the material recycle and recovery of combustion energy are being made, but only a part of the plastic is reused as chemical raw materials. Relating to the R and D of the chemical recycle technology, there are sample studies on the pyrolysis of polyolefine, dechlorination of chlorine base resins, etc. Recently, the following have been made public: proposal of depolymerization monomer based on the cyclic monomer, study of liquefaction of approximately 100% of the thermosetting resin, approach to the solvolysis by supercritical solvent. (NEDO)

  11. FY 1999 report on the study of the future course, etc. of 'the basic survey for promotion of Joint Implementation, etc.'; 1999 nendo 'kyodo jisshi nado suishin kiso chosa' no kongo no hokosei nado ni kansuru kento chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The paper conducted the demonstration of the multiplier effect of 'the model project for heightening of the international energy consumption efficiency, etc.' carried out by NEDO and its subsidiary project, 'the project on the basic survey for promotion of Joint Implementation (JI),' and the comparative study between these projects and the JI/CDM projects proposed in the world. In the quantitative evaluation of the multiplier effect, in the case of making the demonstration of the same technology in the same area both in the model project and the basic survey for promotion of JI, it becomes possible to grasp the CO2 reduction effect with high accuracy, but the CO2 reducible amount is small. Inversely, as to the technology for which the basic survey for promotion of JI is studied, but the model project is not carried out, it becomes possible to grasp the CO2 reduction effect with low accuracy, the CO2 reducible amount is large. In the comparison with the JI/CDM projects proposed in the world, the CO2 reduction amount was approximately $2.7 billion, 250 million tons, in the UNFCCC project, and approximately $5.0 billion, 500 million tons, in the IJ project. There was no very big difference in the cost effect. (NEDO)

  12. Report on the present situation of the FY 1998 technical literature database; 1998 nendo gijutsu bunken database nado genjo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    To study database which contributes to the future scientific technology information distribution, survey/analysis were conducted of the present status of the service supply side. In the survey on the database trend, the trend of relations between DB producers and distributors was investigated. As a result, there were seen the increase in DB producers, expansion of internet/distribution/service, etc., and there were no changes in the U.S.-centered structure. Further, it was recognized that the DB service in the internet age now faces the time of change as seen in existing producers' response to internet, on-line service of primary information source, creation of new on-line service, etc. By the internet impact, the following are predicted for the future DB service: slump of producers without strong points and gateway type distributors, appearance of new types of DB service, etc. (NEDO)

  13. Efeitos antidepressivos da duloxetina e da fluoxetina no teste do nado forçado em ratos

    OpenAIRE

    Ciulla, Leandro; Menezes, Honório Sampaio; Bueno, Bárbara Beatriz Moreira; Schuh, Alexandre; Alves, Rafael José Vargas; Abegg, Milena Pacheco

    2007-01-01

    PURPOSE: To compare the effects of the antidepressant drugs duloxetine and fluoxetine on depressive behaviors in rodents. METHODS: Eighteen male Wistar rats were given systemic injections of duloxetine, fluoxetine, or saline prior to a Forced Swimming Test (FST). Immobility and number of stops were measured. RESULTS: Rats given injections of fluoxetine displayed significantly less immobility (p = 0.02) and fewer stops than the control group (p = 0.003). Duloxetine significanlty reduced the nu...

  14. Report on the present situation of the FY 1998 technical literature database; 1998 nendo gijutsu bunken database nado genjo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    To study database which contributes to the future scientific technology information distribution, survey/analysis were conducted of the present status of the service supply side. In the survey on the database trend, the trend of relations between DB producers and distributors was investigated. As a result, there were seen the increase in DB producers, expansion of internet/distribution/service, etc., and there were no changes in the U.S.-centered structure. Further, it was recognized that the DB service in the internet age now faces the time of change as seen in existing producers' response to internet, on-line service of primary information source, creation of new on-line service, etc. By the internet impact, the following are predicted for the future DB service: slump of producers without strong points and gateway type distributors, appearance of new types of DB service, etc. (NEDO)

  15. 78 FR 28167 - Special Local Regulation, Cruce a Nado Internacional de la Bahia de Ponce Puerto Rico, Bahia de...

    Science.gov (United States)

    2013-05-14

    ... individually or cumulatively have a significant effect on the human environment. This proposed rule involves..., 2013. D.W. Pearson, Captain, U.S. Coast Guard, Captain of the Port San Juan. [FR Doc. 2013-11360 Filed...

  16. El proceso del parpadeo ocular como indicador de emoción en la prueba de nado forzado

    Directory of Open Access Journals (Sweden)

    Samuel Bautista Peña

    2012-11-01

    Full Text Available The relaxed posture of the eyelids keeps the eyes closed, the eyes open is part of the active behavior in living organisms, the activity gives rise to the blinking eye, that for the majority goes unnoticed. You can classify several types of eyeblink, blinking is a response that participates in the facial expression of the emotions. The muscle of the eyelid is essentially involved in emotional responses, as shown during the surprise, fear, or startle. We have studied the eyeblinking linked to aversive events of short duration. We need to know what is happening with the blinking eye to aversive stimuli with longer duration. The forced swimming test (PNF, stimulation provides a sharp, intense and prolonged by 15 minutes. Then we assess the response of eye blinking under the effect of the aversive stimulation provided by the PNF. We used 10 type Wistar male rats experimentally naive, with a weight next to the 300 g were housed with boxes-individual room and free access to food and water. The response of blinking eye was defined as: the behavior of closing and opening in a short period that the eyelids cover the eyes of the rat. We used a modified procedure of the PNF in establishing as a criterion of time 15 minutes for each of the two trials. The first assay began to put the rat in the cylinder with water. The second assay was performed 24 hours after the first assay. The sessions were videotaped, of which the recordings were obtained. The graph shows us a process of change in the blinkin eye, this suggests to us that this is a eyeblinking emotional, which passes through: the surprise; anxiety; and something like depression. It is a complex of processes in which they are involved a variety of mechanisms. We compare our results with other researches of blinking. The descriptors process involved in the anxiety-depression, are at different levels and can go from its link with physiological states until the mechanisms at the biochemical level responsible for that behavior.

  17. Production of ethanol, fat and oil and methane gas from several crops. Sushu sakumotsu nado no energygen toshite no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Uehara, Tsuyoshi; Suganuma, Hirotoshi

    1988-05-01

    Aiming at production of ethanol, fat and oil and so on, ten kinds of miscellaneous cereal crops such as pearl-millet, soybean and so on were grown, and comparative investigation of the production rate which was considered utilization of whole plants were carried out. The suitability of vegetable wastes as methane fermentation materials for the methane gas production was investigated by the constituent analyses and methane fermentation experiments. Nine kinds of the grasses and vegetable wastes such as tomatoe buds, broccoli leaves were used for the investigation. As the results, the estimated yield of ethanol per 10 are from pearl-millet was 690 liter, the estimated yield of fat and oil per 10 are was 70 liter from soybean, The results of the analyses of nine kinds of the farm residues were as follows: (1) carbon content of about 40 %, (2) C/N ratio of 13 av., (3) C/P ratio of 91 av., and (4) the content of C,N and P was roughly appropriate. 680 to 760 milliliter of methane gas was produced from one gram of the dry matter of tomatoe bods, and in case of broccoli leaves, 424 milliliter of methane gas was produced, it was found that these values were not inferior to animal dung. (4 figs, 15 tabs, 6 refs)

  18. Report on evaluation/selection surveys on coal species, processes and others; Tanshu process nado hyoka sentei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This program analyzes the applicable coal species centered by Australia's Victoria brown coal and Chinese coal, which are promising alternative fuel sources for Japan for their reserves, prices, availability, suitability for liquefaction, etc, in order to clarify the possible problems, and commercialize the liquefaction techniques in the early stage. This report consists of 6 chapters. Chapter 1 describes development situations of brown coal, specifically for Australia's Victoria brown coal and Chinese coal. Chapter 2 describes characteristics of the reactions involved in the brown coal liquefaction. Chapter 3 describes current status of various liquefaction processes (solvolysis, solvent extraction, direct hydrogenation and C-SRC) under development in Japan, and problems involved in their future developments. Chapter 4 describes current status of the elementary techniques, e.g., those for slurry pretreatment (e.g., dehydration and crushing), solid/liquid separation, secondary hydrogenation, product upgrading and gasification. Chapter 5 describes the related techniques, and Chapter 6 discusses the demonstration survey results of de-ashing, primary/secondary hydrogenation, and dehydration of brown coal. (NEDO)

  19. Report on evaluation/selection surveys on coal species, processes and others; Tanshu process nado hyoka sentei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This program analyzes the applicable coal species centered by Australia's Victoria brown coal and Chinese coal, which are promising alternative fuel sources for Japan for their reserves, prices, availability, suitability for liquefaction, etc, in order to clarify the possible problems, and commercialize the liquefaction techniques in the early stage. This report consists of 6 chapters. Chapter 1 describes development situations of brown coal, specifically for Australia's Victoria brown coal and Chinese coal. Chapter 2 describes characteristics of the reactions involved in the brown coal liquefaction. Chapter 3 describes current status of various liquefaction processes (solvolysis, solvent extraction, direct hydrogenation and C-SRC) under development in Japan, and problems involved in their future developments. Chapter 4 describes current status of the elementary techniques, e.g., those for slurry pretreatment (e.g., dehydration and crushing), solid/liquid separation, secondary hydrogenation, product upgrading and gasification. Chapter 5 describes the related techniques, and Chapter 6 discusses the demonstration survey results of de-ashing, primary/secondary hydrogenation, and dehydration of brown coal. (NEDO)

  20. Avaliação da resposta imune humoral e análise comportamental de ratos Wistar submetidos a natação forçada e tratados com fluoxetina

    OpenAIRE

    Eduardo Vignoto Fernandes

    2012-01-01

    A fluoxetina é amplamente utilizada para tratamento de transtornos comportamentais. O teste do nado forçado é um modelo experimental de estudo da depressão em ratos, no qual drogas antidepressivas revertem o comportamento passivo de flutuação em repetidas imersões em água. O objetivo deste estudo foi verificar os efeitos da fluoxetina no comportamento do teste do nado forçado e sobre a imunidade. Primeiramente, foi investigado o efeito do teste de nado forçado em relação ao tratamento com flu...

  1. FY 1999 report on the survey of the basic cooperation project of enhancement of the international energy consumption efficiency. Project on promotion of exchanges with the persons concerned with government agencies, etc.; 1999 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo, kokusai energy shohi koritsuka chosa nado kyoryoku kiso jigyo chosa hokokusho. Seifu kikan nado kankeisha koryu sokushin jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of promoting the understanding of effective energy utilization and constructing corporative relations between countries, the persons concerned with government agencies of India, China, Indonesia, Vietnam, Myanmar and Thailand were invited to Japan, and exchanges of opinions were made on policies, technical development, the state of the introduction, etc. The persons concerned with governments of India, China and Indonesia participate in NEDO Forum 2001 to give lectures on the energy policy of their own. The persons sent from the Vietnamese government paid visits for survey to NEDO, Obayashi Corp., Kawasaki Heavy Industries, Ltd., Mitsubishi Materials Corp. and Taiheiyo Cement Corp. as reference of the model project on cement sintering plant power reduction. The persons sent from the Myanmar government paid visits for survey to NEDO, ECCJ, Chiyoda Corp., Yokogawa Electric Corp. and Cosmo Oil Co. as reference of the model project on energy conservation at fertilizer plant. The persons concerned with the Thai government paid visits for survey to the plants concerned with the model project on residue combustion waste heat recovery facilities at paper mills and the model project on waste heat recovery at steel material heating furnace. (NEDO)

  2. Micropropagation of five species of Campanula growing on the territory of Botanical Garden named prof. B.M. Kozo-Polyansky of Voronezh State University

    Directory of Open Access Journals (Sweden)

    O. A. Zemlyanukhina

    2016-01-01

    Full Text Available The development of evidence-based methods of reproduction of protected and highly decorative species that are in high demand for use in landscaping, as well as the establishment of gene pools of species and varieties of plants in actively growing collection corresponds to the main direction of the state coordination program for the development of biotechnology in the Russian Federation until 2020 «BIO 2020». The on-standing research developed and optimized the conditions for obtaining actively proliferating cultures of 5 disappearing species; Campanula rotundifolia L., Campanula persicifolia L., Campanula trachelium L., Campanula rapunculoides L., Campanula glomerata L. Optimized conditions of rhizogenesis. The effect of the different sterilization and antibiotics concentration (kanamycin, benzyl penicillin, gentamicin, klaforan on the growth and development of adventitious plants has been studied. Solutions of antibiotics for sterilization in addition to chlorine-containing agent («Belizna» and mercury (thimerosal are needed. The possible negative effects of the addition of antibiotics in incubation solution lead to increasing of somaclonal variation, neсrosis, disturbance of chlorine synthesis («fatal lack of chlorophyll», slow down the growth of adventitious shoots, and others. It is proposed LED lighting culture in a rack 16 hour period lighting LED strip 12 V power 4.5 W/m (3 LED 10 cm tape, general illumination of 2500–3000 lux. Each shelf is added with red tape photodiodes. The results allow, if necessary, to obtain plantation quantity of these kinds of Campanula in a short time.

  3. Travel time and ray path computation in 2D-heterogeneous structures; Fukinshitsu kozo ni okeru jishinha soji oyobi hasen no atarashii keisan hoho

    Energy Technology Data Exchange (ETDEWEB)

    Fujie, G; Kasahara, J; Sato, T; Mochizuki, K [The University of Tokyo, Tokyo (Japan). Earthquake Research Institute

    1996-05-01

    Methods were studied for determining the initial travel time and ray paths with stability when an non-linear travel time inversion is performed in an inhomogeneous structure. The travel time calculation was based on Faria and Stoffa`s method. First, the 2-dimension space was sectioned by grids, and `slowness` was assigned to all the lattice points. Starting from the vibration source, travel time at each lattice point is sequentially calculated. This method calculates travel time for any structure without breakup. In this study, an algorithm more sophisticated than the method of Faria, et al., was developed, and the improvement of travel time calculation accuracy led to the accurate determination of the direction of incidence into the lattice points during the initial motion. The calculation of ray paths was effected by tracing back from the receiving points the incidence into the lattice points or by following back the ray paths to the vibration source. This method performs stable calculation for a heavily inhomogeneous structure and, with the algorithm being simple, do the parallel programming as well. 1 ref., 6 figs., 1 tab.

  4. Subsurface interpretation based on geophysical data set using geothermal database system `GEOBASE`; Chinetsu database system `GEOBASE` wo riyoshita Kakkonda chinetsu chiiki no chika kozo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Osato, K; Sato, T; Miura, Y; Yamane, K [Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Doi, N [Japan Metals and Chemicals Co. Ltd., Tokyo (Japan); Uchida, T [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

    1996-05-01

    This paper reports application of a geothermal database system (GEOBASE) to analyzing subsurface structure in the Kakkonda geothermal area. Registered into the GEOBASE to analyze specific resistance structure in this area were depth information (well track and electric logging of existing wells), three-dimensional discretization data (two-dimensional analysis cross section using the MT method and distribution of micro-earthquake epicenters), and two-dimensional discretization data (altitude, and depth to top of the Kakkonda granite). The GEOBASE is capable of three-dimensional interpolation and three-dimensional indication respectively on the three-dimensional discretization data and the depth information table. The paper presents a depth compiling plan drawing for 2000 m below sea level and an SE-NE cross section compiling cross sectional drawing. The paper also indicates that the three-dimensional interpolation function of the GEOBASE renders comparison of spatial data capable of being done freely and quickly, thereby exhibiting power in the comprehensive analysis of this kind. 3 refs., 8 figs., 2 tabs.

  5. Relationship between herbicide's fate of the river flowing into lake Teganuma and its molecular structure. Teganuma ryunyu kasen ni okeru josozai no dotai to bunshi kozo no kankei

    Energy Technology Data Exchange (ETDEWEB)

    Tamura, J [Nishi Tokyo University, Yamanashi (Japan). Faculty of Science and Engineering; Ogura, N [Tokyo University o Agriculture and Technology, Tokyo (Japan). Faculty of Agriculture

    1994-04-10

    Environmental profiles of agricultural chemicals in a river flowing into Lake Teganuma were surveyed. Their dissolution and adsorption were investigated by using indoor experiments, and their behaviors were discussed from a viewpoint of molecular structure in the compounds. The herbicides detected in the river contained CNP and Benthiocarb were at high concentration at the time of spraying, but decreased sharply thereafter. The CNP had lower concentration than Benthiocarb in the river, indicating little amount flowing out from paddy fields. These differences in the environmental profiles should be attributable to natures of the herbicides. An indoor experiment has revealed that Benthiocarb has lower solubility and higher absorption strength than CNP. It was found with respect to the chemical structures that polarity increases if hetero atoms and hydrophilic substituents exist in moleculars; the solubility of Benthiocarb grows higher than that of hydrocarbons; and adsorption power relates to the area of contact with absorbing media, and absorption rate relates to the solubility, absorption power, and three-dimensional structure. 23 refs., 7 figs., 4 tabs.

  6. FY1995 study of very flexible software structures based on soft-software components; 1995 nendo yawarankana software buhin ni motozuku software no choju kozo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The purpose of this study is to develop the method and tools for changing the software structure flexibly along with the continuous continuous change of its environment and conditions of use. The goal is the software of very high adaptability by using soft-software components and flexible assembly. The CASE tool platform Sapid based on a fine-grained repository was developed and enforced for raising the abstraction level of program code and for mining potential flexible components. To reconstruct the software adaptable to a required environment, the SQM (Software Quark Model) was used in managing interconnectivity and other semantic relationships of among components. On these two basic systems, we developed various methods and tools such as those for static and dynamic analysis of very flexible software structures, program transformation description, program pattern extraction and composition component optimization by partial evaluation, component extraction by function slicing, code encapsulation, and component navigation and application. (NEDO)

  7. FY 1998 report on the results of the project on the next generation structure housing development; 1998 nendo jisedai kozo jutaku kaihatsu jigyo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The purpose of this project is to develop/verify technology to design/construct a structural body of multiple dwelling house which is highly durable and usable at maximum of the limited space with no projections of poles/beams, and is also to develop/verify a composite system of a structure and each house in which residential space can freely be changed horizontally/vertically in response to the leveling-up of living and changes in life style. The following were conducted: construction of an experimental house group with next generation structure; development of technology of effective space utilization/high durability body construction; development of technology of structural analysis/design systematization of antiseismic/damping system; development of commercialization of technology to heighten frame durability, development of technology to heighten durability of finishing materials of a body; development of low cost construction technology; development of technology of interface between a body and each house; verification of housing performance using a next generation body system; generalization of next generation frame system/house system. To reflect the results of the research quickly, the details of the research are systematized, and a draft is worked out of a guide for constructing the next generation frame system/house system which were arranged between the current architecture related laws and business as a general multiple dwelling house. (NEDO)

  8. Mesoporous activated carbons with metal-oxide particles prepared from Morwell coal; Morwell tan wo genryo to shita kinzoku sankabutsu tanji kasseitan no saiko kozo

    Energy Technology Data Exchange (ETDEWEB)

    Yoshizawa, N.; Yamada, Y.; Shiraishi, M. [National Institute for Resources and Environment, Tsukuba (Japan); Kojima, S.; Tamai, H.; Yasuda, H. [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

    1996-10-28

    The metal dependence of mesoporous activated carbons with various metal acetylacetonate (acac) particles prepared from Morwell coal was studied. In experiment, the mixture of Morwell coal and acac metal complexes were dissipated into tetrahydrofuran, and after agitation in Ar atmosphere, the solvent was removed by vacuum distillation. Coal specimens with Fe(acac)3, Ni(acac)2 and Co(acac)2 as acac complexes were activated by exchanging flow gas with water vapor after heat treatment in N2 gas flow at 900{degree}C. The pore sizes of the specimens were obtained from N2 adsorption isotherms by BET method and BJH method. Conditions of pores and metals in the specimens were examined by XRD measurement and TEM observation. The relation between the above conditions and pore characteristics obtained from adsorption experiment was also examined. As a result, the difference in mesopore ratio between the specimens and blank specimens was larger in the order of Fe, Co and Ni, and the effect of added metal complexes was also larger in this order. 3 refs., 3 figs., 3 tabs.

  9. Bond cleavage reactions of the bridge structure in coal in the presence of hydrogen donating compounds; Suiso kyoyosei kagobutsu sonzaika deno sekitanchu no kakyo kozo no kairetsu hanno

    Energy Technology Data Exchange (ETDEWEB)

    Bando, N.; Kidena, K.; Murata, S.; Nomura, M. [Osaka University, Osaka (Japan). Faculty of Engineering

    1996-10-28

    In this paper, bond cleavage reactions are discussed in relation to the softening and solubilization of coal. Were used 9,10-dihydroanthracene (DHA) and 9,10-dihydrophenanthrene (DHP) as models of hydrogen donating compounds in coal, and bibenzyl, 1,2-diethane, benzylphenylether, and 1,5-dibenzylnaphthalene were used as models of bridge structure compounds. They were compared mutually, as to reactivity of coal against DHA and DHP. For the homolytic cleavage of bridges, DHA with excellent radical supplement performance provided excellent hydrogen donating performance. While, for the ipso-position cleavage of bridges, it was found that DHP can act as an effective hydrogen donor. For the reaction between coal and hydrogenated aromatic compounds, cleavage of relatively weak bonds, such as ether linkage and dimethylene linkage, occurred at about 380{degree}C, and hydrogen from DHA or DHP was consumed. On the other hand, the results suggested that the cleavage reaction at ipso-position affected by hydrogen donating solvent is also important at temperature range around 420{degree}C. 2 refs., 3 figs., 1 tab.

  10. Optimum stamping die structure based on analytical method of die deformation during draw process; Seikei katei no kanagata henkei kaiseki ni motozuku, press kanagata kozo no saitekika

    Energy Technology Data Exchange (ETDEWEB)

    Nakahara, T; Tamai, H [Mazda Motor Corp., Hiroshima (Japan)

    1997-10-01

    We measured an actual deformation and pressure distribution in draw process of bending cam, and analyzed deformation process of die structure, in order to eliminate adjusting work considering die deformation by stamping force. We studied die structure improvement with simulation based on analytical method. This report describes a sample of die structure improvement based on a simulation and actual measurement. 1 ref., 11 figs., 1 tab.

  11. Characteristic analysis of turbulent heat diffusion in a multi-compartment structure; Takukakuka kukan kozo ni okeru ranryunetsu kakusan gensho no kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Hu, C; Fukuchi, N [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1997-10-01

    An analysis was made on turbulent heat diffusion in a multi-compartment structure necessary for designing calorific power and environment for functional systems used in marine vessels and off-shore structures. In a multi-compartment structure, the diffusion phenomenon is complex because of movement of air flow in turbulence and buoyancy resulted from non-isothermal condition. The phenomenon is largely affected by space shapes and walls, and the conditions in heat diffusion field is governed also by shapes of opening connecting the compartments. An analysis was made by using the SIMPLE method on turbulent heat diffusion in a multi-compartment space with high Raleigh number in which natural convection is dominant. If the opening is small, the Coanda effect appears, in which air flow passing through the opening rises along the wall, wherein a high-temperature layer is formed near the ceiling, making the heat diffusion inactive. If the opening is large, a jetting flow from the opening and a large circulating flow are created, which cause active advection mixture, making temperature gradient smaller in the upper layer. Heat transfer intensity in an opening on a partition wall decays in proportion with 1/4th power of the opening ratio. 7 refs., 11 figs.

  12. Fiscal 1994 survey report. Survey of energy supply/demand structure sophistication and global environmental impact; 1994 nendo energy jukyu kozo kodoka chikyu kankyo eikyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Outlines of various energy supply/demand analytical models are surveyed. With environmental problems gathering importance, a number of models are being introduced in which energy supply/demand structures, long-term climate changes, and impacts of policy options on social economy are linked to each other. Some socioeconomic impact models cover a single country and others the whole world. They are various in type, ranging from dynamic optimization models to static balance models. Twenty-four models are chosen, and grouped into two types respectively covering Japan and the whole world from a geographical viewpoint and into three groups in view of their structures. Under an optimization model, such optimization is accomplished as economic growth maximization and energy cost minimization and so forth under given energy supply restrictions. Under a general balance type econometric model, an adjustment process in which capital and labor and production are coordinated across multiple departments is expressly stated. Under a partial balance type econometric model, a demand function for goods is given and optimum behavior such as consumption maximization is indirectly described. (NEDO)

  13. Fabrication of low cost high performance large size composite structures by electron beam curing (EBC); Denshisen koka (EBC) ni yoru tei cost koseino ogata fukugozai kozo no seizo

    Energy Technology Data Exchange (ETDEWEB)

    Kamimura, K.; Parrot, P.

    1996-03-15

    This article introduces the electron beam curing (EBC), which is high speed non-heating cure technique for the high performance resin for structures, conducted by Aerospacial Co., Ltd. In this technique, very strong electron beam and X-ray are used in response to the thickness of curing region of members, and the muzzle has energy of 10 MeV as permeation control energy and power of 20 kW as cure time control power. Advantages of fabrication of composite products by EBC is derived from the elimination of exoergic and heating curing processes and the local cure molding. For the EBC, the residual stress is not generated, the size is stable, the insertion of different materials is easy without mismatch of thermal expansion between the composites and metals, the homogeneous bridge can be obtained to stabilize the material quality, the processing time can be shortened, it is suitable to mass production, and the cure of products can be controlled. About 30% to 40% of the cost of products can be reduced. 1 ref., 6 figs., 1 tab.

  14. Basic investigation on deflection wave propagation and strength of very large floating structures; Choogata futai kozo no tawami hado denpa kyodo to kyodo ni kansuru kisoteki kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tsubogo, T.; Okada, H. [University of Osaka Prefecture, Osaka (Japan). Faculty of Engineering

    1997-08-01

    The response strength in which deflection waves propagating in the elastic body of a large floating structure with an order of km in length and width was investigated. Attention was paid to the waves propagating the place fully away from the boundary of a very large floating body so as to obtain the dispersion relation of waves and the relation between incident waves and deflection waves. Next, the frequency response was checked from the aspect of the displacement amplitude and strength for beams and plates. The dispersion relation of waves propagating the place fully away from the boundary of a very large floating body and the relation between the waves and infinite-point incident waves were represented by an expression. Similarly, the waves propagates more than the infinite-point incident waves in frequency, wavelength, and speed. A lower-limit value exists in the propagation speed. The displacement and stress amplitudes are represented by a relational expression. For plates, the displacement amplitude increases when the wave direction coincides with the small-rigidity direction. The stress amplitude is maximized when the waves corresponding to the ``wave below a floating body = size of a characteristic wave number`` reach the large-rigidity direction. 10 refs., 10 figs., 2 tabs.

  15. Extension of the Fukaya fault and deep structure of the Konan terrace; Fukaya danso no encho to Konan daichi no chika kozo

    Energy Technology Data Exchange (ETDEWEB)

    Yamaguchi, K; Kano, N; Yokokura, T; Kiguchi, T; Yokota, T; Tanaka, A [Geological Survey of Japan, Tsukuba (Japan); Sato, H [The University of Tokyo, Tokyo (Japan). Earthquake Research Institute

    1997-10-22

    With an objective to elucidate the relationship between the central tectonic line in the Kanto area and the active faults appearing in topography, seismic exploration using the reflection method has been carried out. The course of traverse was set in the south west to north east direction starting from the north east part of the Kanto mountainous area to the Menuma lowland passing through the Konan high plain. The line crosses nearly perpendicularly the direction in which the general beds in this area run. A 400-kg weight was used as a vibration source in the western half of the course of travel, and the MinivibT15000 (made by IVI Corporation) in the eastern half. Considerations given based on the preliminary CMP polymerization time cross section may be summarized as follows: the Fukaya fault cannot be tracked topographically further to the south east side than Mikejiri in Kumagaya City, but the reflection face from CMP 2050 to about 2100 shows an inclined bed on the south west side and a horizontal bed on the north east side; judging from change in the inclination in the beds, the Fukaya fault is thought to extend to the south east direction; the location of inclination change on the cross section turns to the south west side as the depth increases; and, if this is regarded as the fault face, the Fukaya fault could be said an inverse fault. 5 refs., 2 figs.

  16. Simulation of fault-bend fold by incompressible Newtonian fluid; Hiasshukusei Newton ryutai ni yoru danso oremagari shukyoku kozo no simulation

    Energy Technology Data Exchange (ETDEWEB)

    Tamagawa, T; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan); Tsukui, R [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-10-22

    Incompressible Newtonian fluid simulation is experimentally applied to faults typical of the compression and extension fields. A fault-bend folding structure of the flat-ramp flat fault in the compression field and a folding structure of a normal fault in the extension field are studied, and the results are compared with those obtained by the balanced cross section method. The result of calculation indicates that the velocity gradient with the ramp angle set at 30deg is correspondent to stress and that stress concentration is taking place at the ramp section of the fault. This solution is an approximation and does not necessary support the conservation of area but, when the ramp angle is allowed to change from 10 through 40deg, it is found that the conservation of area holds though roughly. It is found that the configuration of the folding structure formed by a flat-ramp flat fault is positioned between the anomalous-mode layer parallel shear typical of a balanced cross section and the folding structure formed by a vertical shear. 7 refs., 7 figs.

  17. Estimation of underground structures in Kyoto city by seismic-array observations of microtremors; Bido no array kansoku ni yoru Kyoto shinai no chika kozo tansa

    Energy Technology Data Exchange (ETDEWEB)

    Miyakoshi, K; Kagawa, T; Akazawa, T [Osaka Soil Test, Osaka (Japan); Ogawa, Y; Shimizu, K [Osaka Gas Corp., Osaka (Japan); Ejiri, J [Obayashi Corp., Tokyo (Japan)

    1997-10-22

    Observations of microtremors were carried out to estimate the S-wave velocity structure by using arrays of seismographs around the Kyoto Research Park. The observation points were so arranged that equilateral triangle arrays may be formed with maximum radii at 0.2 km, 0.4 km and 0.8 km respectively with the premises of the Kyoto Research Park as the center. The seismographs have used seven vertical movement components (PELS), and were adjusted to a period of eight seconds. In addition, high-cut filters of 4 Hz were used because the observation areas are located in urban areas with heavy traffic. The analysis has used the spatial self-correlation method as a means to estimate phase velocity of surface waves contained in microtremors. As a result, phase velocity estimation has become possible for frequencies from about 0.4 Hz to 2 Hz, whereas the S-wave velocity structure was estimated to a depth of down to about 900 m by using as reference the result of the reflection method exploration having been carried out in the present areas. In addition, it was suggested that microtremors with frequencies higher than 1 Hz are in unsteady state in terms of time or space. 4 refs., 7 figs., 1 tab.

  18. Experimental analysis of the structure attenuation characteristics on engine noise by pseudo cylinder pressure excitation; Giji tonaiatsu kashin ni yoru engine kozo no soon tokusei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Ozawa, H; Nakada, T [Isuzu Advanced Engineering Center, Tokyo (Japan)

    1997-10-01

    The engine structure attenuation has been experimentally analyzed by the newly developed in-cylinder excitation system. It can reproduce the complete cylinder pressure in non-running engine conditions by adopting the hydraulic and the piezoelectric actuator. The structure attenuation measured in this system has a good coincidence with the ones measured in actually engine operating conditions, meanwhile the current method, which applied only high frequency components as the excitation pressure, was shown to have the unsatisfied agreement. As a result, the proposed system has been concluded to be very useful to estimate the engine noise characteristics in non-running conditions. 4 refs., 11 figs., 1 tab.

  19. Geoelectrical structure by electrical logs and Schlumberger sounding at the Akinomiya geothermal field, Akita Prefecture; Denki kenso oyobi Schlumberger ho ni yoru Akinomiya chinetsu chiiki no hiteiko kozo

    Energy Technology Data Exchange (ETDEWEB)

    Kajiwara, T; Takemoto, S

    1997-05-27

    Based on the electrical logging data of the existed well and Schlumberger sounding data obtained in 1974, a two-dimensional inversion analysis of the specific resistance profile was conducted at the Akinomiya geothermal field, Akita Prefecture. From the electrical logging data, relationships between the geology and the specific resistance were illustrated. The specific resistance values of basement rocks showed more than 100 ohm-m, which were higher than those of the other seams. Intrusive rocks and tuffs in the basement rocks showed locally low values less than 100 ohm-m. Younger volcanic rocks showed low values around 10 ohm-m. As a result of the two-dimensional inversion analysis, the basement rocks could be detected as high specific resistance layers. Accordingly, it was considered that the basement rocks in this field can be detected as high specific resistance layers by analyzing the results of field survey sufficiently. Low specific resistance zones were observed in the shallow depth, which corresponded to the fumarolic gases. There were some layers with remarkably varied specific resistance values, which were considered to be related with alteration. 6 refs., 3 figs.

  20. Efficient calculation of potential distribution in two-layer earth; Niso kozo daichikei ni okeru denki tansa no tame no koritsuteki den`i keisan shuho

    Energy Technology Data Exchange (ETDEWEB)

    Kataoka, M; Okamoto, Y [Chiba Institute of Technology, Chiba (Japan); Endo, M; Noguchi, K [Waseda University, Tokyo (Japan); Teramachi, Y; Akabane, H [University of Industrial Technology, Kanagawa (Japan); Agu, M [Ibaraki University, Ibaraki (Japan)

    1997-05-27

    An efficient calculation method of potential distribution in the presence of an embedded body in multi-layer earth has been proposed by expanding the method of image with a consideration of multiple reflection between the ground surface and each underground boundary. For this method, when solving boundary integral equation with the potential of embedded body surface as only one unknown, i.e., when obtaining discretization equation, ordinary boundary element program developed for analyzing the finite closed region can be used. As an example, numerical calculation was conducted for the two-layer earth. The analysis expression of potential distribution in the case of the certain embedded body in two-layer earth has never published. Accordingly, the calculated results were compared with those by the integral equation method. As a result, it was concluded that the primary potential obtained from the present method agreed well with that obtained from the integral equation method. However, there was a disregarded difference in the secondary potential. For confirming the effectiveness, it was necessary to compare with another numerical calculation method, such as finite element method. 5 refs., 5 figs.

  1. Subsurface interpretation based on geophysical data set using geothermal database system `GEOBASE`. 2; Chinetsu database system `GEOBASE` wo riyoshita Kakkonda chinetsu chiiki no chika kozo kaiseki. 2

    Energy Technology Data Exchange (ETDEWEB)

    Osato, K; Sato, T; Miura, Y; Yamane, K [GERD Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Doi, N [Japan Metals and Chemicals Co. Ltd., Tokyo (Japan); Uchida, T [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

    1997-05-27

    Five cross sections were applied as a result of MT method investigations in addition to the results of conventional analyses at the Kakkonda geothermal area; three-dimensional resistivity distribution was made into a database by using the Kriging method which makes a matching with anisotropy of seismic center distribution in micro-earthquakes; and the database was compared with the data derived from surveys on the pilot survey well WD-1a and the side-truck well WD-1b thereof. As a result, it was found that the well WD 1b which encountered a water loss zone had the water loss zone exist in a region with relatively lower resistivity than in the well WD-1a which did not encounter a water loss zone. The region in which the water loss zone was encountered existed in a very steep slope region going from the high resistivity region in the west side toward the low resistivity region in the east side. This fact suggests a possibility that fractures have developed in this region with sharp slope in the resistivity in this area. Adding three-dimensional complementary function to the GEOBASE database by using a simple Kriging allowed the direction of anisotropy in spatial data to be freely and quickly decided. It was learned that this capability exhibits strong power in a mapping work in structures where such anisotropy as a geothermal zone is highly dominant. 5 refs., 8 figs., 2 tabs.

  2. X-ray diffraction analysis and MO calculations of 1H-tetrazole; 1H-tetorazoru no Xsen kessho kozo kaiseki to bunshi kido keisan

    Energy Technology Data Exchange (ETDEWEB)

    Ono, Yoshio.; Akutsu, Yoshiaki.; Arai, Mitsuru.; Tamura, Masamitsu. [The University of Tokyo, Tokyo (Japan). School of Engineering; Matsunaga, Takehiro. [National Institute of Materials and Chemical Research, Tsukuba (Japan)

    1999-02-28

    The X-ray diffraction analysis and the MO calculations of 1H-tetrazole were carried out, in order to explain its high stability. From the X-ray diffraction analysis, five bonds in the ring have intermediate lengths between single and double bond lengths. Therefore, 1H-tetrazole is quite stable because of its aromaticity. The N1-C5 distance of 1.315A is significantly short. The molecular structure which was calculated by the ab initio MO calculation of one 1H-tetrazole molecule at MP2/6-31G* level, showed a good agreement with our experimental one, except for the abnormal short N1-C5 distance. From the calculations of dimers and trimers, 1H-tetrazole is shown to be stabilized by a strong intermolecular electrostatic interaction between the protons and the delocalized electrons over the ring. (author)

  3. Fiscal 2000 report on result of the full-length cDNA structure analysis; 2000 nendo kanzen cho cDNA kozo kaiseki seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper explains the results of research on full-length cDNA structure analysis for the period from April, 2000 to March, 2001. The outline of human genome sequence was published in June, 2000. In Japan, human gene analysis was such that, as the basic technology of the bio industry, a millennium project was decided in the budget of fiscal 2000. The full-length cDNA structure analysis is the core of the project. The libraries of cDNA were prepared using full-length and more than 4-5kbp-long cDNAs by oligo-capping method. It began from determining partial sequence data at end cDNA, and then, with new clones selected therefrom, full-length human cDNA sequence data were determined. The partial sequence data determined by fiscal 2000 were 1,035,000 clones while the full-length sequence data were 12,144 clones. The sequence data obtained were analyzed by homology search and translated into amino acid coding sequences, with predictions conducted on protein functions. A clustering method was examined that selects new clones from partial sequences. Database was constructed on gene expression profiles and disease-related gene sequence data. (NEDO)

  4. Buckling collapse analysis of framed structures by using adaptively shifted integration technique. Junnogata shifted intergration ho ni yoru honegumi kozo no zakutsu hokai kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Toi, Y.; Isobe, D. (The University of Tokyo, Tokyo (Japan). Institute of Industrial Science)

    1993-09-01

    This paper describes the following matters on application of an adaptively shifted integration technique to a buckling collapse analysis of framed structures: This method is a method in a finite element analysis using three-dimensional girder elements to arrange value integration points at optimal locations in a linear analysis if the elements are in an elastic transform condition on the whole. The method then moves the value integration points so that plastic hinge will occur in these locations immediately after part of the elements has yielded. The method was applied to analyzing an elastic buckling problem in several loading patterns for either a both-end supported or a one-end fixed beam member. A result was obtained that a number of elements required for one member is four at minimum. In a buckling analysis of framed structures, a satisfactory result was obtained by using an automatic element segmenting algorithm, which begins the analysis with one element one member, and immediately after a member is determined with a possibility of generation of buckling, splits that member only into four elements. 6 refs., 5 figs.

  5. Structural studies on reaction centers from thermophilic photosynthetic bacteria and its functional utilizations. Tainetsusei kogosei saikin ni yuraisuru kogosei hanno chushin no kozo kaimei to kino kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Nozawa, T; Morishita, Y; Kobayashi, M; Kanno, S [Tohoku University, Sendai (Japan). Faculty of Engineering

    1992-10-31

    This paper describes the results of the experiment in which crystallization of protein of reactive center purified from the photosynthetic film of thermophilic purple sulfur photosynthetic bacterium Chromatium tepidum whose hyrogen donor in photosynthesis is H2S instead of H2O was attempted. Crystallization was carried out by the vapor diffusion method and particularly by using ethylene glycol as precipitator at 4[degree]C after various investigations on the conditions of crystallization. By X-ray diffraction, this crystal was found to belong to the rhombic system, and it was estimated that the lattice constants, a, b, c equal to 140[angstrom], 190[angstrom] and 80[angstrom] respectively. This bacterium is a thermophilic bacterium having the optimum growth temperature of 48-50 [degree]C and utilizes CO2 or H2CO3 as corbon source, ammonium, urea etc. as nitrogen source and thiosulfate as sulfur source. Moreover, another purpose of this investigation was to determine the thermophilic location by elucidating its configuration (although, as a result, the analysis of configuration had no sufficient resolution). It was confirmed that the enzyme system of photosynthetic film and its cytoplasm obtained by ultrasonic spallation of this cell have CO2 fixing activity utilizing light energy. 23 refs., 14 figs., 3 tabs.

  6. Life prolongation and cost reduction of steel ladles with improving refractories and their structure; Taikabutsu zaishitsu to kozo kaizen ni yoru shuka taikabutsu no chojumyoka to kosuto teigen

    Energy Technology Data Exchange (ETDEWEB)

    Nakai, Masato; Kasahara, Hajime; Fukutani, Fujio; Imai, Hiroyuki [Nippon Steel Corp., Tokyo (Japan)

    1999-06-01

    Steel Making Plant, Hirohata Iron Works, Nippon Steel Corp. succeeded to reduce the cost of furnace materials by measures described below down to 49% compared to that in 1992. (1) For tuyre bricks, cleanability against oxygen was improved by compacting by vacuum cast forming. (2) For SL bricks, the cost was reduced by applying imported bricks and optimization of the range of use. (3) For alumina-magnesia amorphous refractories for side walls, low expansion and breaking resistance were improved by optimization of magnesia quantity and silica ultra fine powder quantity. (4) For side wall structure, improvement of tie-in between the ground part and the side wall and lining with efficient thickness were carried out. (NEDO)

  7. Nonlinear effects and vortical structures in homogeneous rotating turbulence under stable density stratification; Antei seisoka ni aru kaiten ichiyo ranryu no hisenkei koka to uzu kozo

    Energy Technology Data Exchange (ETDEWEB)

    Tsujimura, S.; Iida, O.; Nagano, Y. [Nagoya Institute of Technology, Nagoya (Japan)

    2000-02-25

    The generation mechanism of the vertical vortices associated with the baroclinic instability and the effects of nonlinear term on the vortices are investigated by using both direct numerical simulation (DNS) and rapid distortion theory (RDT). Two kinds of the anisotropic flow fields are used as initial conditions. As a result, the initial anisotropy of Reynolds stresses is found to affect asymmetry of the vertical vortices. In the cases where the initial vertical velocity is set to be zero, the p. d. f. of the vertical vorticity tends to incline toward the anticyclonic side. When the vertical component of initial velocity is larger than the horizontal one, the cyclonic vortices are more enhanced. By comparing DNS and RDT, it is found that in both cases of the initial conditions the enhanced vortices of DNS are stretched in the vertical direction, which is not observed in the RDT results. This should be because the nonlinear vortex-stretching term intensifies and elongates vertical vortices in the vertical direction. The anticyclones are markedly augmented in low Prandtl number fluids, while the cyclones become dominant in the high Prandtl number case. In particular, the flow field becomes almost two-dimensionalized and Taylor columns are formed in the vertical direction in the low Prandtl number case. However, neither two-dimensionalization nor Taylor column is observed in the RDT analysis which neglects the nonlinear terms. (author)

  8. Coal structure construction system with construction knowledge and partial energy evaluation; Kochiku chishiki to bubunteki energy hyoka ni yoru sekitan bunshi kozo kochiku system

    Energy Technology Data Exchange (ETDEWEB)

    Okawa, T.; Sasai, T.; Komoda, N. [Osaka University, Osaka (Japan). Faculty of Engineering

    1996-10-28

    The computer aided coal structure construction system is proposed, and a computational construction example is presented. The coal structure construction engine of this system fabricates molecular structure by connecting fragments sequentially inputted through a user interface. The best structure candidate is determined using construction knowledge and partial energy evaluation every addition of one fragment, and this process is subsequently repeated. The structure evaluation engine analyzes the 3-D conformation candidate by molecular dynamics, and evaluates the conformation by determining the energy value of an optimum structure. As an example, this system was applied to construction of coal molecular structure based on the actual data of partial structure composed of 26 structures from 2l kinds of aromatic cluster structures, 27 bonds from 2 kinds of bridged bonds, and 16 groups from 2 kinds of terminal substitutional groups. As a result, this system could construct a superior structure according to expert knowledge from the viewpoint of energy. 6 refs., 5 figs., 2 tabs.

  9. Correlation between the structural relaxation and the functionality of optically functional glasses; Kokinosei glass ni okeru kozo kanwa to kinosei no sokan

    Energy Technology Data Exchange (ETDEWEB)

    Nishida, T [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1994-12-15

    A discussion was given to elucidate the correlation between the crystallization of infrared ray permeating glass and the infrared ray permeability. The elucidation used infrared ray permeation spectrum, infrared ray absorption spectrum, and the Mosbauer effect. Reduction in permeability due to heat treatment of aluminate glass was discussed from the crystallization mechanism. Ultrafine crystals of mayenite phase having a composition ratio of CaO/Al2O3 = 1.7 diffuse and grow from the glass surface into interior as a result of heat treatment. The crystal growth is triggered by severance of Al-O tetrahedron. Gallate glass has CaGa2O4 and small amount of CaFe2O4 phase deposited when it is heat-treated in the vicinity of Tg. Although the infrared ray permeability decreases in association with the crystallization, the decrease is limited to crystallization on the glass surface, hence the permeability will not fall to zero. Laser irradiation on the gallate glass causes crystallization, resulting in reduced infrared ray permeability. Semi-stable Ca3Ga4O7 phase remains, however, because the heat energy amount is not large. Tellurite glass has {alpha}-TeO2 and a small amount of telluric acid iron deposit when heat-treated. 29 refs., 10 figs.

  10. Integration of the market of the European Community and the change of the industrial structure; EC shijo togo to sangyo kozo no henka

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, T; Uno, K; Tanimoto, T; Yamashita, T [Osaka Sangyo University, Osaka (Japan). Institute for Industrial Research

    1994-11-22

    This paper describes progress of the cooperation as to the integration of EC market and the change of industrial structure. For the structural change in the industry and economy accompanied by the integration of EC, effects of the Maastricht Treaty on the economic structure of EC are described. It is considered that the EC countries are affected by the political and economical restrictions due to the agreement of this treaty. For the change in the distribution structure accompanied by the integration of EC, obstruction factors of the deregulation of EC transportation market are especially investigated. Differences in the distribution capacity, various regulations and standards, and labor condition among individual countries are pointed out as the obstruction factors. For the unity of Germany and its economical and administrative influence, various problems are pointed out as to the economical confusion, progress in the de-nationalization of enterprises, management of real estate and land, etc. For the structural change in the road freight market in the member nations of EC, the structure of road freight market is made clear for the previous West Germany before the integration of European market. It is confirmed that the internationalization of the German domestic market is being promoted.

  11. Integration of the market of the European community and the change of the industrial structure. EC shijo togo to sangyo kozo no henka

    Energy Technology Data Exchange (ETDEWEB)

    Tanimoto, T; Uno, K; Nakamura, T; Yamashita, S [Osaka Sangyo University, Osaka (Japan). Institute for Industrial Research

    1992-11-20

    This paper considers problems in the change of the industrial structure as a result of the EC market integration, and the change of the physical distribution structure, mainly in cargo transportation. The market integration is being moved forward mainly on liberalization of flows in people, materials, and currencies, but the material flow liberalization has not progressed noticeably because of difficulty in deregulations. Changes in the transportation structure on the whole in the EC countries would not see a complete removal of barriers supported by the transportation licensing system because of issues in protecting domestic transportation markets and sharing the road expenses, even if the tariff barrier has been removed as a result of the market integration. Amid the predictions on deregulated legislations and intensified competition associated with the integration, the French trucking industry is indicated of its direction toward a two-layer structure comprising large-scale enterprises and medium-to-small companies. The German unification created problems in transferring from the socialistic command economy to the capitalistic market economy. The paper gives considerations on the real state of affairs in the privatization policy of the people-owned enterprises in the former East Germany, and its economic and managerial problems that should be solved amid the large-area EC market integration based on the mutualism over and above the economic system transition.

  12. Crustal temperature structure derived from a ground temperature gradient chart of Hokkaido; Hokkaido no chion kobaizu kara motometa chikakunai ondo kozo

    Energy Technology Data Exchange (ETDEWEB)

    Okubo, Y. [Geological Survey of Japan, Tsukuba (Japan); Akita, F. [Hokkaido Geological Survey, Sapporo (Japan); Nagumo, S. [Oyo Corp., Tokyo (Japan)

    1997-05-27

    The Hokkaido Underground Resources Investigation Institute has prepared in 1995 a detailed temperature gradient chart that shows local anomalies around volcanoes. This paper describes an attempt to derive crustal temperature structure of Hokkaido from the above data. The model was hypothesized as a primary model in which no thermal convection exists. In volcanic and geothermal areas which show a temperature gradient of more than 100 {degree}C km {sup -1}, a solidus temperature is reached at a depth shallower than 10 km. Below the volcanic chain forming the Chishima arc, a partially melted region exists in a width of about 100 km. Most of the areas in the southern Hokkaido have the temperature reached the solidus temperature in the crust. On the other hand, in most of the areas of the forefront side, no solidus temperature is reached in the crust. In the temperature structure of a cross section crossing almost orthogonally with the volcanic front passing through Mt. Daisetsu, a high temperature area reaches to a shallow portion beneath Mt. Daisetsu, where the depth at which the solidus temperature is reached is 10 km or shallower. The range of area where the solidus depth is shallower than 10 km has a south-west width of about 40 km. This means that a partially melted area with a size of 40 km in the horizontal direction exists at a depth of several kilometers. 20 refs., 3 figs.

  13. Bayesian reliability analysis for non-periodic inspection with estimation of uncertain parameters; Bayesian shinraisei kaiseki wo tekiyoshita hiteiki kozo kensa ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Itagaki, H. [Yokohama National University, Yokohama (Japan). Faculty of Engineering; Asada, H.; Ito, S. [National Aerospace Laboratory, Tokyo (Japan); Shinozuka, M.

    1996-12-31

    Risk assessed structural positions in a pressurized fuselage of a transport-type aircraft applied with damage tolerance design are taken up as the subject of discussion. A small number of data obtained from inspections on the positions was used to discuss the Bayesian reliability analysis that can estimate also a proper non-periodic inspection schedule, while estimating proper values for uncertain factors. As a result, time period of generating fatigue cracks was determined according to procedure of detailed visual inspections. The analysis method was found capable of estimating values that are thought reasonable and the proper inspection schedule using these values, in spite of placing the fatigue crack progress expression in a very simple form and estimating both factors as the uncertain factors. Thus, the present analysis method was verified of its effectiveness. This study has discussed at the same time the structural positions, modeling of fatigue cracks generated and develop in the positions, conditions for destruction, damage factors, and capability of the inspection from different viewpoints. This reliability analysis method is thought effective also on such other structures as offshore structures. 18 refs., 8 figs., 1 tab.

  14. Global environment assessment survey by advancing the energy demand and supply structure. 4; Energy jukyu kozo kodoka chikyu kankyo eikyo chosa. 4

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    To investigate the energy demand and supply structure in Japan, the international trend of approaches to global warming problems and the mitigation options to global warming in the energy related sectors have been surveyed. For the United Nations Framework Convention on Climate Change, an Ad-hoc Group has discussed relevant topics after the 1st conference of the Parties. Meetings of the Group primarily focused on what objectives to set for the reduction of greenhouse gas (GHG) emissions in and in and after 2000. IPCC completed their Technical Paper in November 1996 in which technologies and measures to reduce GHG emissions and to enhance GHG sinks were analyzed and evaluated in various aspects. This Paper discusses about each sector of institutional buildings sector, transport sector, industrial sector, and energy supply sector. Especially, in the energy supply sector, promising approaches to reduce future emission include more efficient conversion of fossil fuels, switching to low-carbon fossil fuels, decarbonization of flue gas and fuels, CO2 storage, switching to nuclear energy, and switching to renewable sources of energy. 5 refs., 2 figs., 14 tabs.

  15. Studies on surface structures and mechanism of photocatalytic action of semiconductor oxides; Handotai hikari shokubai no hyomen kozo seigyo to sayo kiko kaimei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Takeuchi, H; Sona, S; Koike, H; Hori, H; Negishi, N; Kohara, H; Ibusuki, A [National Institute for Resources and Environment, Tsukuba (Japan); Vakhtin, A; Borovkov, V [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

    1997-02-01

    Studies are made to define the working mechanism of semiconductor photocatalysts such as TiO2 and to establish designing guidelines for improving on their activity and functions. TiO2 in the air actively produces oxygen seeds for the oxidation and removal of NOx, etc. It is desired that a catalyst have a specific surface area large enough to retain the product of its action. To meet the need, a thin-film photocatalyst which is an aggregate of TiO2 crystals is produced by burning a film of a sol/gel system of reaction doped with macromolecules. This product has a larger specific surface area and is higher in pollutant-removing performance, and may be put into practical use. In another experiment, metal-carrying particles TiO2 suspended in water are employed for the reduction of CO2. Though the main product of catalysts carrying Pt or Pd is methane, a photocatalyst carrying RuO2 produces acetic acid mainly and loses less activity with the passage of time. A hybrid photocatalyst is composed of an organic pigment and inorganic semiconductor, synthesized through a covalent bond between a sililated-surface thin TiO2 film and porphyrin. It is confirmed that the newly developed process brings about an increase in electron migration efficiency. 3 figs.

  16. Survey of effects of enhancement of the energy supply/demand structure on the global environment. 3; Energy jukyu kozo kodoka chikyu kankyo eikyo chosa. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    For the purpose of studying how the energy supply/demand structure in Japan should be, a report on the secondary IPCC (Intergovernmental Panel on Climate Change) evaluation was analyzed. Possibilities of reducing the world CO2 emissions in association with the energy consumption were studied in the five assumed cases. Every case says that CO2 can be reduced to 1/3 of the 1990 level by 2100. In a case of the use of biomass as main fuel (1), the use of primary energy is suppressed to two times the 1990 level, and photovoltaic/wind/biomass power generation is introduced in a large quantity. Synthetic methanol and hydrogen are used for transportation and commercial/residential use fuels. There are four more assumed cases: the use of nuclear power as a substitute for renewable energy in the power generation in (1), the use of natural gas of 1.5 times that used in (1), the substitution of coal for biomass used in (1), and the assumption that the demand for primary energy in 2100 will be twice that used in (1). In Japan it is assumed that basically the nuclear power generation will be expanded, that the photovoltaic and waste power generation will be introduced in a large quantity, and that synthetic methanol and hydrogen are mainly used as transportation and commercial/residential use fuels. It is necessary, therefore, to analyze conditions under which the quantity introduction of such non-fossil energy is made possible. 11 figs., 31 tabs.

  17. NEDO coal mining structure adjustment subcommittee. 18th project report meeting; NEDO sekitan kogyo kozo chosei bunkakai. Dai 18 kai jigyo hokokukai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    Concerning the subject matter, a NEDO (New Energy and Industrial Technology Development Organization) director Keishiro Kawamo reports on NEDO's projects designed to smoothly implement the 'new coal policy'. Nobuaki Terasaka, chief of the planning division, coal and new energy department, Agency of Natural Resources and Energy, takes up the current status of the coal policy and the tasks it faces, and discusses, predicting the development of the coal policy, the assurance of stable supply of coal from abroad, development of clean coal technologies that will rightly deal with the world-wide environmental problems, and the international diffusion of the clean coal technologies and the completion of the basement therefor. Concerning the 'development of zeolite-related commodities,' a report is delivered on the manufacture of a soil improving material and a deodorant for fish grill from zeolite found rich in coal layers of Pacific Coal Mine Co., Ltd. Concerning the 'polycrystalline diamond manufacturing project,' a polycrystalline diamond synthesizing method making use of the blasting technique employed at coal mines is reported. (NEDO)

  18. Report on fiscal 1998 investigation of Jozankei hot spring conservation and hot spring structure; 1998 nendo Jozankei onsen hozen chosa. Onsen kozo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-10-01

    With the purpose of evaluating recoverable hot water quantity and elucidating the change over a long term, investigations were carried out, with the results summarized, on the geology, alteration zone, gravitational analysis, fluid geochemistry and hydraulics in the area. The investigations covered the area of 7 km x 6 km in about 30 km southwest of Sapporo City and were performed for the period from September 10, 1998 to October 31, 1999. The results were as follows. In the Jozankei area, with the Usubetu layer in the Old Tertiary system as the basement, layers are superposed from the Palaeogene Oligocene to the Quaternary Pleistocene. Distributing in various places between Yunosawa vicinity and Jozankei Hot Spring area are acid to neutral geothermal alteration zones. The hot spring gushing-out zone in the Jozankei hot spring area is supposed to be regulated by side-by-side cracks in the NE-SW direction. It was inferred from tritium concentration and a minor component ratio that, as the mechanism of forming a hot spring, water of precipitation origin circulating and residing for a long time on the Usubetsu layer which is marine sediment is heated by a volcanic heat source latent in the depth. (NEDO)

  19. Learning model of eye movement system based on anatomical structure; Kaibogakuteki kozo ni motozuita gakushu kino wo motsu gankyu undo system to sono tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, X.; Wakamatsu, H. [Tokyo Medical and Dental University, Tokyo (Japan)

    1998-07-01

    A learning system is proposed to explain the adaptive function of an eye movement consisting of compensatory and optokinetic reflex, and pursuit movements based on the brain anatomy and physiology. Thereby, the learning system is synthesized as an artificial neural network based on the structure and function of the biological neural network of flocculus. The role of neural paths into flocculus from stretch receptors of ocular muscles are discussed in detail from the viewpoint of system control engineering. The mathematical learning process is also shown taking into account the adaptive mechanism and the anatomical structure of vestibular nuclei. The experimental results through simulation confirm the validity of the hypothesis and the appropriateness of the inference process in connection with the proposed mathematical model. 18 refs., 11 figs.

  20. Hybrid structure in civil engineering construction. Composite types of steel and concrete; Doboku bun`ya ni okeru fukugo kozo. Kozai to concrete no ittai keishiki

    Energy Technology Data Exchange (ETDEWEB)

    Sato, T. [JR Railway Technical Research Inst. Tokyo (Japan)

    1995-03-30

    In connection with hybrid structures in civil engineering construction, classification and application of composite types of steel and concrete are discussed. H steel embedded beam is a composite beam in which the H shape steel of the main beam is connected to rolled or welded H shape steel using cross beams. Composite structure columns are grouped into the composite column and the steel pipe concrete column. SRC piers are often adopted from the viewpoints of constraints for execution of works and vibration proof. Steel and concrete hybrid structure is a kind of structural system in which various kinds of materials such as steel, RC, or PC members are connected. The cable stayed bridge utilizes characteristics of steel and concrete effectively. For the piers of municipal expressway viaducts, there are executed cases of mixed structures which have RC, SRC columns for T shape piers and S structure for the bridges. SRC structure and composite columns are adopted often for structures of subway stations. 7 refs., 7 figs.

  1. Some studies on structural planning of long-span cable stayed bridge; Choshikan shachokyo no kozo keikaku ni kansuru 2,3 no kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Endo, T. [NKK Corp., Tokyo (Japan)

    1997-06-20

    Feasibility of cabled-stayed bridges with 1000m-grade spans is discussed while re-examining the plan for constructing a Great Tatara Bridge to connect Honshu and Shikoku, Japan, and in this process various tasks and questions are isolated. Some which will be problems in designing the new bridge structure are taken up, including the load-bearing capability of the bridge as a whole, vibration of long cables, resistance to long-period earthquakes, and accuracy management during the construction work. Findings are stated below. A cable-stayed bridge is not significantly different from a suspension bridge and is sufficiently feasible until the span exceeds 1500m. When the span is longer, however, the bridge beam cross section needs be designed very prudently in view of the great axial force and wind load to be imposed on it. Effective for the assurance of load-bearing capability for a long-span cabled-stayed bridge is a structure in which load is elastically confined in the direction of the bridge axis. In connection with vibration damping for very long cables, it is verified that a new dimpled cable suits the purpose of suppressing wind load from increasing without reduction in damping effect. 28 refs., 23 figs., 7 tabs.

  2. Creep analysis and torsional vibration analysis of cable-stayed bridges with two edge composite girders; Nishuketa gosei kozo shachokyo no creep kaiseki to nejiri shindo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Hoshino, M. [Nihon University, Tokyo (Japan). College of Science and Technology

    1996-07-21

    This paper describes the creep analysis and torsional vibration analysis of cable-stayed bridges with two edge composite girders. The girder is composed of the concrete slab and the steel girder. I-girders are placed at both edges of the profile. Such a type of bridge was investigated. As the stress migrates by the creep of concrete slab, it is necessary to evaluate the influence of this creep precisely in designing. In the analysis, the composite girder was expressed not by the single member, but by the binary member consisting of concrete member and steel member. Two methods were employed, i.e., method A in which both members are connected by the rigid body beam and method B in which the profile of concrete is converted into the profile of steel. The method A provided better accuracy, but the method B was often sufficient. Torsional rigidity of the open profile structure was much smaller than that of the box profile. As the torsional natural frequency was low, proper torsional vibration analysis was indispensable especially from the viewpoint of wind resistance. Two methods were employed, which utilize the vibration analysis method for general space frame structures. Results of both methods were agreed mutually, but the second method provided better calculation efficiency. 10 refs., 9 figs., 6 tabs.

  3. Studies on connecting structure between steel shell and steel reinforced concrete; Kokaku to tekkotsu tekkin concrete tono ketsugo kozo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Morimoto, A. [Kinki University, Osaka (Japan). Faculty of Science and Engineering; Morikawa, H.; Ito, N. [Metropolitan Expressway Public Corp., Tokyo (Japan)

    1996-02-15

    On the insert reinforcing bar structure for the connecting part of the main tower of cable stayed bridges, this paper reports verification results on a load resistant safety with a full-scale model, structure analysis and construction work. The basic structure was composed of a drilled steel shell, inserted reinforcing bars, fixing structure of bars in lining concrete of the shell and a pressure bearing plate. As an experimental result, the connecting part had a sufficient load carrying capacity against both tensile and compressive loads. The shear stress of the insert reinforcing bar structure was estimated successfully under von Mises`s condition. The shear spring constant in deformation characteristics was linearly proportional to an inserted reinforcing bar ratio. In earthquake, nearly 60% of an allowable compressive load was transferred to concrete through the pressure bearing plate. The analytical results of load resistant deformation characteristics of the connecting part well agreed with experimental ones, and the proposed analytical model was applicable to estimation of a dynamic behavior. 5 refs., 22 figs., 4 tabs.

  4. Proposal and study of a long-span composite cable-stayed bridge with new hybrid girder; Atarashii gosei kozo shuketa wo mochiita chodai fukugo shachokyo no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, K.; Hishiki, Y.; Furuichi, K. [Kajima Corp., Tokyo (Japan)

    1999-09-30

    A hybrid or mixed structure (composite structures) are a matter of increasing concern which takes in each advantage of steel and concrete. A field of bridges is no exception, with the plan and construction carried out for the new type of composite bridge, such as a composite cable-stayed bridge and a composite extra dose bridge as a long span bridge, and a composite truss bridge and a corrugated steel plate web bridge as a medium-span bridge, with technological development becoming active in this field. In such a technological trend, a hybrid two-girder structure was devised, a structure consisting of a concrete filled steel pipe for a girder and a precast (PC) floor plate for a floor board, as the girder structure of a long-span cable-stayed bridge in the subject research; also, applicability was examined using, as an example, the composite cable-stayed bridge with hybrid girders employed for the span. This paper reports the result of the analysis of the entire system, the analysis made for the purpose of examining the characteristic and the feasibility of this hybrid girder. The analysis revealed the structural feasibility of the long-span composite cable-stayed bridge using two hybrid girders of concrete-filled steel pipes thus devised. (NEDO)

  5. Bayesian reliability analysis for non-periodic inspection with estimation of uncertain parameters; Bayesian shinraisei kaiseki wo tekiyoshita hiteiki kozo kensa ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Itagaki, H [Yokohama National University, Yokohama (Japan). Faculty of Engineering; Asada, H; Ito, S [National Aerospace Laboratory, Tokyo (Japan); Shinozuka, M

    1997-12-31

    Risk assessed structural positions in a pressurized fuselage of a transport-type aircraft applied with damage tolerance design are taken up as the subject of discussion. A small number of data obtained from inspections on the positions was used to discuss the Bayesian reliability analysis that can estimate also a proper non-periodic inspection schedule, while estimating proper values for uncertain factors. As a result, time period of generating fatigue cracks was determined according to procedure of detailed visual inspections. The analysis method was found capable of estimating values that are thought reasonable and the proper inspection schedule using these values, in spite of placing the fatigue crack progress expression in a very simple form and estimating both factors as the uncertain factors. Thus, the present analysis method was verified of its effectiveness. This study has discussed at the same time the structural positions, modeling of fatigue cracks generated and develop in the positions, conditions for destruction, damage factors, and capability of the inspection from different viewpoints. This reliability analysis method is thought effective also on such other structures as offshore structures. 18 refs., 8 figs., 1 tab.

  6. Achievement report for fiscal 1998 on research and development of multifunction members structure control technologies. Development of advanced surface treatment technologies for methane-fueled aero engines (1. Microstructure control technologies for ultrahigh temperature members); 1998 nendo fukugo kino buzai kozo seigyo gijutsu no kenkyu kaihatsu. Methane nenryo kokukiyo engine buzai no kodo hyomen kako gijutsu kaihatsu (chokoon buzai mikuro kozo seigyo gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The carbon fiber reinforced carbon composite materials (C/C composites) strong at ultrahigh temperatures are taken up. So as to improve on its resistance to oxidation, corrosion, and abrasion as well as on its strength at ultrahigh temperatures, an ion engineering-assisted technique is used to reform the C/C composite surface layer and a technology is developed for thin coating formation on the C/C composite surface. Next, technologies are developed for multifunction coating formation on top of the surface, for defect prevention or removal from the C/C composite, and for adhesion enhancement between the C/C composite fibers and the matrix. Technologies are further developed for evaluating hostile environment withstanding capabilities at ultrahigh temperatures. In this fiscal year, in the study of microstructure controlling multilayer coating technologies, development is conducted of technologies of ion engineering-assisted surface control and reform and of technologies of forming multifunctional coatings high in reliability and resistance to corrosion. In the field of microstructure control composition, 3-dimensional carbon fiber reinforced carbon composite materials are manufactured by way of trial and evaluated, and their behavior under rigorous conditions is evaluated. (NEDO)

  7. FY 2000 report on the results of the research and development project for new industry creation type industrial science technologies. R and D of the intellectual material and structural systems (R and D of the intellectual material and structural systems); 2000 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki kozo system no kenkyu kaihatsu (chiteki kozo system no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 2000 results of the R and D project for development of intellectual materials and structural systems, where the fibrous or leafy sensor material or element (muscle) is integrated with a structure of an advanced material (skeleton) to process and control information (brain). The program for development of the health monitoring technologies successfully improves the fine FRG (Fiber Bragg Grating) as the high-performance sensor, equipped with a connector which allows the sensor to be easily connected to the normal diameter one, and develops various prototype sensors. The program for self-diagnosis of structural soundness and controlling damages verifies detection effectiveness of the embedded fine FRG sensor. The impact-related characteristics and damages of the reinforced flat plate are detected by embedding the optical fiber sensor. The program for developing the actuator materials and elements prepares the 20{mu}m thick piezoelectric sheet of adequate strength and toughness by dispersing the PNN-PZT system with partially stabilized zirconia (PSZ). The program for the function-gradient systems prepares the FGM driven at normal temperature, characterized by its structure of more evenly distributed stress, to evaluate its characteristics. It is proved to have high durability. The results of the comprehensive survey are also described. (NEDO)

  8. Study on fabrication methods of composite structures (1st. report); Joule effect curing of CFRP composite structures and its application to bonding and repair. Fukugo zai kozo no seikei kako ho ni kansuru kenkyu (Dai 1po); CFRP kozo no Joule koka wo riyo shita cure ho to setsugoter dot hoshu e no oyo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Moriya, K. (The National Defense Academy, Kanagawa (Japan))

    1990-07-05

    A method for curing CFRP composite structures by using Joule effect is presented. Due to the presence of fiber to fiber contact, CFRP composites and their prepregs exhibit electrical conductivity in the direction transverse to fibers as well as in the fiber direction, and they can be considered as electrically homogeneous on a gross scale. Therefore, passing an electric current through a CFRP prepreg, it is self-heated due to the Joule effect. Feedback current control maintains the prepreg temperature at a desired level and makes the prepreg be cured by a specified cure cycle. Experimental verifiactions have been carried out to demonstrate the feasibility of the present technique. The applications to the bonding of CFRP components and to the patch repairs of effective CFRP structure are also described. 12 refs., 12 figs.

  9. Exploration of underground basement structures in Kanto plain using the spatial autocorrelation method. 1. S-wave velocity structure along the line from Hatoyama, Saitama to Noda, Chiba; Kukan jiko sokanho ni yoru Kanto heiya no kiban kozo tansa. 1. Saitamaken Hatoyama machi - Chibaken Nodashi kan no S ha sokudo kozo

    Energy Technology Data Exchange (ETDEWEB)

    Matsuoka, T; Umezawa, N; Shiraishi, H [Saitama Institute of Environmental Pollution, Saitama (Japan)

    1997-05-27

    The Saitama prefectural government has been conducting basement structure exploration using the spatial autocorrelation method by dividing the entire plain area into meshes, for the purpose of improving the accuracy of estimating large-scale seismic damages. This paper reports the result of explorations on meshes in the east-west direction in the central part of Saitama Prefecture. The present exploration was intended on ten meshes in the east-west direction along the north latitude 36-degree line. The number of exploration points is 13 comprising three points on the hilly area bordering on the eastern edge of the Kanto mountainous area and ten points on the plain area. The arrangement constitutes a traverse line with a total distance of about 33 km from the west edge (Hatoyama-machi in Saitama Prefecture) to the east edge (Noda City in Chiba Prefecture). The phase velocities were estimated from the result of the array microtremor observations using the spatial autocorrelation method applied with the FET. The phase velocities were used to estimate underground structures by using an inverse analysis. As a result, detailed two-dimensional S-wave velocity structures were revealed on the traverse line. The velocity cross section expresses change in the basement structures with sufficient resolution, and at the same time the information is judged highly harmonious with existing deep boring data and the result of artificial earthquake exploration. 15 refs., 6 figs.

  10. Field experiment in jointed rock mass with electro-magnetic tomography. Challenge for 50m energy penetration and an interpretation with additional geological data; Denjiha tomography ni yoru setsurisei ganban no tansa. Kokan kyori 50m no sokutei to chishitsu kaishaku no kokoromi

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, K; Koga, K; Nishiyama, E; Yamamoto, T [Kawasaki Geological Engineering, Co. Ltd., Tokyo (Japan)

    1996-05-01

    With the purpose of extending an exploring distance in electromagnetic tomography, a prototype was made as a device to receive and transmit continuous waves in a borehole, so that a tomographic observation was carried out on a jointed rock mass that had a conventionally short exploring distance. The device consisted of a transmitter, receiver, antenna, cable and surface controller, with a personal computer used for displaying and storing data. The prototype antenna was provided with a size insertable into a VP50 vinyl chloride tube. In order to determine a relative permittivity of a rock, a boring core was shaped and an impedance was measured. The measurement of tomography was carried out at 1m spaces apart in the bore holes with a distance of 50m in between. The received waveforms were stored in a floppy disk built in the personal computer. As a result of the analysis, a tomographic cross-section of the electromagnetic wave velocity was obtained, showing the distribution of sandstone with a high electromagnetic wave velocity and little joints, shale with a low electromagnetic wave velocity, chart with a high electromagnetic wave velocity, etc. 2 refs., 4 figs., 1 tab.

  11. Report on fiscal 1998 investigation of geothermal development and promotion and on supplementary investigation concerning data processing (geology/decomposed zone investigation and gravitational probing). No. B-7 Kuwanosawa area; 1998 nendo chinetsu kaihatsu sokushin chosa. Data shori ni kakawaru hosoku chosa (chishitsu henshitsutai chosa oyobi juryoku tansa) hokokusho (No.B-7 Kuwanosawa chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-30

    A geology/alteration zone investigation and gravitational probing were carried out, with the results summarized, for the purpose of elucidating the structure of geothermal reservoir structure in the Kuwanosawa area. The investigation was implemented in the southeast part of Akita prefecture including Yuzawa city and Ogachimachi during the period between June 9 and August 31, 1999. The results were as follows. The geology of the investigation area consists of granite, as the base rock, and the covering Doroyu layer, Minasegawa layer, Sanzugawa layer and intrusive rocks in the Neo Tertiary system as well as Kabutosan layer and volcanic rocks in the Quaternary system. No wide area alteration zone existed, while vein-like alterations and hydrothermal veins along cracks were recognized, with the fluid inclusion homogenizing temperature showing 240-260 degrees C, which presumably indicates the existence of local hydrothermal activity until comparatively recently. The geothermal structure of the subject area is very likely dependent on thermal conduction from a deep thermal source existing in the Wasabizawa district. In the underground depth, it is inferred that a hydrothermal system is formed in the NW fault structure, lower part of cracks accompanying NS hydrothermal vein, and in the NNW/NE structures inferable from the gravitational probing. (NEDO)

  12. ONRASIA Scientific Information Bulletin. Volume 17, Number 4, October-December 1992

    Science.gov (United States)

    1992-12-01

    Singapore will soon etc.) but enabling technologies. We join Japan as the only Asian have to bear in mind that new Dr. Scow Boon Quek countries with...Thomas F. 3-237 Donoghue, Michael 1-137 Lu, Stephen 4-063 Flynn, Anita 2-099 Meyer, Robert A. 3-173 Fujii, Kozo 4-099 Moffett, Jonathan D. 1-061 Gibor

  13. Basic survey on the residence using hybrid energy in snowy cold regions; Sekisetsu kanreichi ni okeru hybrid energy katsuyogata jutaku nado ni kansuru kiso chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The conceptual model and feasibility of the hybrid energy system for residences and public facilities in snowy cold regions were studied. Based on the existing data, the existing and available amounts of natural energy and unused energy in the target area, Sapporo were estimated. Based on the predicted energy demands of 4 kinds of building models, the energy systems for such models were studied. The use of the following energies was considered: photovoltaic power generation and solar heat for all the models, household sewage energy for the multiple-dwelling house model, and wind power generation for the public facility model. The annual energy balance was calculated to evaluate it. The use of additional commercial electricity was necessary, while surplus solar heat energy was found in summer which can push up the self-sufficiency rates of the residence and public facility models to 70% and 44%, respectively. The multiple- dwelling house model which can use a large amount of household sewage energy could utilize 80% of new energy, while the other 3 models utilized only 60-70% of that. 81 figs., 42 tabs.

  14. Fiscal 2000 collection of manuscripts for technology development committee on hydrogen energy and the like; 2000 nendo suiso energy nado kanren gijutsu kaihatsu iinkai yokoshu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-07

    The subjects listed in the collection are (1) the research and development of international clean energy system technology utilizing hydrogen (WE-NET - World Energy Network), including the outline of the project as a whole; research on system evaluation; research and development of safety measures; development of technologies for liquid hydrogen transportation and storage; research on low-temperature materials; development of hydrogen supply station and hydrogen-driven automobile system; development of supply station for hydrogen produced by electrolysis of water; development of hydrogen fuel system; development of hydrogen production technology; development of hydrogen absorbing alloys for dispersed hydrogen transportation and storage; development of polymer electrolyte fuel cell fed with pure hydrogen; and the development of power generation technology, (2) the development of closed type high-efficiency turbine technology capable of carbon dioxide recovery, and (3) the development of frontier technology of carburation using sensible heat in coke oven gas. (NEDO)

  15. Research report for fiscal 1998. Study of utilization of biomass including foods in energy industry; 1998 nendo shokubutsu nado no biomass no energy riyo ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Rice being produced as food is taken up out of various types of biomass, and a feasibility study from the viewpoints of technology and economy is conducted as to its use in the energy industry. The production of ethanol from rice, though it has no past record worth discussion, is similar to the production of ethanol from other biomass resources in terms of technology and economy. The problem is that the production cost of rice is far higher than those of other materials. It is expected, however, that there will a large-scale production cost reduction and an increase in the yield when novel cultivation techniques are introduced in the future. It is also expected that alcohol from rice will be sufficiently competitive with alcohol from molasses or the like when the exploitation of cellulose-family by-products such as husks becomes feasible. The study on this occasion deals solely with the effective use of farmland and the surplus rice. A confrontation between rice as a biomass resource and rice as a food has to be avoided as much as possible in the long term because it may cause a price rise and compromise the security of food supply. That is, in discussing this matter, it is mandatory to draw a very definite line between rice as a food and rice as an alcohol production material. (NEDO)

  16. Survey of the waste-fueled power generation introducing technology. Case study 1 (fiscal 1996); Haikibutsu hatsuden donyu gijutsu chosa nado. Case study no jisshi 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A case study on A city was conducted aiming at making a detailed manual for introducing the waste-fueled power generation. The study was made in terms of a large-capacity waste-fueled power plant, estimation of the waste amount considering wide-area processing, size of facilities, comparison of four types of combustion furnace, steam condition/seawater cooling/power generating efficiency, etc. As a result, the following were proposed: As to the size of facilities, a capacity as large as possible is recommended in the light of the scale merit of costs of the waste-fueled power plant and final disposal site and the environmental preservation. Concerning the high efficient power generation, recommended are 450degC and 60-80 ata which are steam conditions for coping with high temperature corrosion. In respect to seawater cooling, the adoption is recommended making good use of locational conditions since the output energy increases by approximately 16%. Any furnace types including the fluidized bed furnace are equal. The amount of dioxin becomes below 0.1ng/Nm{sup 3} because of the control of furnace combustion temperature, residence time, catalytic desulfurization facilities, blowing of activated coal into the flue, etc. 172 figs., 78 tabs.

  17. Achievement report for fiscal 2000 on development of technology to evaluate reliability of petroleum refining facilities; 2000 nendo sekiyu seisei setsubi shinraisei hyoka nado gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper reports the achievements in fiscal 2000 in development of a technology to evaluate reliability of petroleum refining facilities. The development efforts were made mainly on analyses by simulation and neural net (NN) that utilize computers. In the high-temperature system facilities, the creep damage generation is governed by different factors including impurities. The evaluation on joint life requires simultaneous use of low temperature zone long-time test. Verification was made on application of non-destructive inspection, such as use of ultrasonic waves in the accelerated creep zone. Defect detecting capability was identified when an ultrasonic wave flaw detection model is used for buried piping. In the pulse eddy current flaw detection, a coil most superb in totality was selected by means of simulation, by which corrosion and wall thickness of piping and devices were detected from outside the sheathing materials. Development was made on a technology to diagnose and evaluate corrosion of tank in operation by using the AE method. The remaining life of transformers is determined by how seriously the coil insulating paper has been deteriorated, and furfural in the oil was found effective for the parameters. Particularly, application of the NN was revealed to be effective in estimating electric motor deterioration. A high-temperature sulfide corrosion rate estimating model was developed from the operation and measurement data of the facilities by applying the NN and TCBM. (NEDO)

  18. Fiscal 2000 survey report on regional new energy vision formulation for Kawanabe town, Kagoshima Prefecture; 2000 nendo Kawabecho chiiki shin energy vision sakutei nado chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A regional new energy vision has been formulated for Kawanabe town, Kagoshima Prefecture, to be participated in by inhabitants and beneficial to both natural environment protection and inhabitants. The results of the survey are described in six chapter which involve (1) the basic philosophy of vision formulation, (2) outline of new energy, (3) environmental characteristics and townspeople's awareness, (4) energy situation and the amount of new energy existing in Kawanabe town, (5) regional new energy vision for Kawanabe town region, and (6) future tasks. After a study of the existing amount of new energy, energy demand, and people's requests, it is concluded that photovoltaic power generation, wind power generation, hot spring heat utilization, small scale water energy, and refuse-derived energy be the types to be preferably introduced into the town. Projects are established and concrete plans are prepared thereunder, which concern the reinforcement of public relations and enlightening activities, installation of a wind power system as one of enlightening activities, study of Kawanabe town's own subsidy system for encouraging the introduction of photovoltaic power systems and solar heaters for domestic use, and the introduction of photovoltaic power systems into public facilities such as school houses. In conclusion, it is hoped that, since financial difficulties will be a strong factor to impede new energy introduction, the subsidy system will be a solid one. (NEDO)

  19. Fiscal 1999 survey report. Fiscal 1998 basic survey for promotion of joint implementation, etc. (Analysis of results); 1998 nendo kyodo jisshi nado suishin kiso chosa kekka no bunseki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The 40 'Surveys for promotion of joint implementation, etc.' conducted by NEDO (New Energy and Industrial Technology Development Organization) in fiscal 1998 aimed to pick out projects that would positively utilize the flexible measures (three Kyoto mechanisms) for the achievement of greenhouse gas reduction targets defined at COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change). In this paper, concerning these 40 surveys, studies are conducted for reaching conclusions about setting baselines for the future, execution of similar feasibility studies in the future, application of flexible measures, and opinions towards project implementation. The 40 surveys were, concretely speaking, conducted not to work out policies for actualization of given projects but to consider philosophies of project actualization and baseline formation for the future. In this paper, project outlines, environmental impact assessment, and economic assessment (investment assessment) are put in order for each of the surveys, and relations between amounts of global warming gas reduced and project costs, and project profitability, are analyzed for each of the surveys. (NEDO)

  20. Report on new energy vision establishment project in Higashi Naruse Village area; Higashinarusemura chiiki shin energy vision sakutei nado jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A new energy vision was established in the Higashi Naruse Village in Akita Prefecture. The population of the village is continuing the decreasing trend since 1950 to 3,390 persons as of 2000. The annual energy demand in this village is about 320,000 GJ, accounted for by the consumer department at about 40%, the transportation department at about 36% and the industrial department at about 24%. The carbon dioxide emission amount therefrom is estimated 6,300 t-C annually. The expected usable quantity of new energies in the village would be available, in the decreasing order, in the wind power as the most promising source, forestry bio-mass, snow cold heat energy, agricultural bio-mass, and solar beam (heat). The total quantity would be 514,330 GJ annually in heat utilization, and 85,305 MWh in electric power. The new energy introducing project includes introduction of photovoltaic and wind power generation into Kurikoma Mountain Villa, introduction of wind power generation into the Junes skiing area and Oyanagi Natural Park, introduction of photovoltaic power generation and heat utilization into primary and middle schools, introduction of clean energy fueled automobiles into the village office, and introduction of photovoltaic power generation into general houses. (NEDO)

  1. Report on evaluation/selection surveys on coal species, processes and others. Appendix; Tanshu process nado hyoka sentei chosa hokokusho. Furoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This report, consisting of 7 chapters, summarizes literature related to liquefaction of coal. Chapter 1 describes the results of the (Project Lignite), i.e., development of the concept of two-stage liquefaction of lignite. Chapter 2 describes the COSTEAM process, which uses synthesis gas (CO-H{sub 2}) as the reducing agent and coal moisture as the hydrogen source for liquefaction of coal of low degree of carbonization, e.g., brown coal. Chapter 3 describes solubilization of coal with alcohol, where coal is reacted with ethanol and NaOH at 300 to 420 degrees C. Chapter 4 describes liquefaction of coal and production of lighter products with tetrahydroquinoline as the hydrogen donor. Chapter 5 describes low-temperature carbonization as the process for liquefying coal, in particular brown coal. Chapter 6 describes possibility of development of new liquefaction techniques for brown coal, including solvolysis for liquefaction, role, recovery and reuse of catalysts, short contact time processes, and coal pretreatment. Chapter 7 describes economic viability of the secondary hydrogenation. (NEDO)

  2. Fiscal 2000 survey report on regional new energy vision formulation for Kito village; 2000 nendo Kitoson chiiki shin energy vision sakutei nado chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A regional new energy vision has been formulated for Kito village, Tokushima Prefecture, in the hope that it will trigger off an effort to build a mentally affluent community. Kito village is a 2,000-strong village situated in a mountainous region, and consumed 1.3 times 10{sup 5} GJ in energy in fiscal 1999. The results of activities conducted in this connection are summarized in four chapters which are (1) the outline of survey, (2) local characteristics, (3) existing amount of new energy, and (4) plans for promoting new energy introduction and energy conservation. Discussed as plans for promoting new energy introduction and energy conservation are a business of commercialization feasibility survey, plot to construct a natural energy operated school building, and a plan for promoting energy conservation. Discussed in relation to commercialization feasibility survey are a small scale hydroelectric power generation utilizing a sand-trap dam, small scale hydroelectric power generation utilizing waste water from a fish farm, regional heat supply business utilizing ligneous biomass, manufacture of ligneous pellet fuel, and so forth. In relation to the promotion of energy conservation, a drive will be launched to positively bring photovoltaic power generation into daily life. (NEDO)

  3. Achievement report for fiscal 2000 on development of technologies to reduce pollutants in oil refining; 2000 nendo sekiyu seisei osen busshitsu teigen nado gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development has been made on technologies to reduce sulfur content in light oil and on optimization of light oil quality. This paper summarizes the achievements in fiscal 2000. In the study of enhancing the desulfurization rate in gas oil deep hydrodesulfurization process, it was found that NiHY zeolite having Ni introduced by using the ion exchange method shows stable activity, whereas the target of sulfur content of 50 ppm or lower was achieved by adding the third constituent and by optimizing the impregnation solution to pH3. In the study of the Ni, Mo/alumina catalyst, the desulfurization activity was enhanced by optimization of carrier pore size to 120 to 140 angstroms and by addition of phosphorus and silica, having the target of sulfur content of 50 ppm or lower achieved. In the research of manufacturing low-sulfur light oil using heavy oil desulfurization and hydrocracking, optimization was performed on the catalyst used in the latter stage of heavy oil desulfurization, and evaluation was given on the performance in combination of commercially available hydrometallation catalyst/middle part HDS catalyst/bottom part HDS catalyst. As a result, achievement of the target of sulfur content in the desulfurized light oil of 300 ppm or lower was verified. Life evaluation test is in continuation on the heavy oil hydrocracking catalyst. (NEDO)

  4. Research report for fiscal 1998. Promotion of activities implemented jointly etc. in China; 1998 nendo Chugoku ni okeru kyodo jisshi katsudo nado suishin chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The Kyoto Protocol allows some flexibility in the implementation of methods for achieving the goal, such as emission trading, activities implemented jointly (AIJ) among advanced countries, construction of clean development mechanisms (CDM) with developing countries, etc., and Japan intends to positively make use of them for the achievement of the goal. For China, who holds second place in the list of greenhouse gas emitting countries in the world, the promotion of CDM is quite important. With the situation taken into consideration, interaction was effected with Chinese officers and scientists of government agencies and academic institutes involved in environmental matters, and researches were conducted. Views and information were exchanged regarding environmental problems and, after on-site investigations, researches were conducted and suggestions were presented as to how AIJ and CDM should be. The suggestions covered Chinese policies toward AIJ and CDM, current state of AIJ projects in China and systems for their promotion, means for enhancing such projects, and discovery of candidates for AIJ and CDM project application. (NEDO)

  5. Fiscal 1998 achievement report. Research and development of simplified dioxin analyzing technology, etc.; 1998 nendo dioxin kan'i bunseki gijutsu nado kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A simplified method is developed, which measures dioxins in flue gas without using GC/MS (gas chromatography/mass spectrometry) of the double focusing type. The sampling device is built of two collecting bottles, containing water and diethylene glycol, and uses no XAD-2 (cross-linked amberlight divinyl benzene) resin. Such a design does not need time consuming Soxlet extraction in the sampling process and shortens the processing time. An HPLC (high performance liquid chromatography) system replaces the convenient column chromatography system in the cleanup process, and this enables automation and rapid treatment. For the measurement of toxicity equivalent, GC/MS is used to separate and quantify 17 kinds of toxic isomers as in the conventional method. The GC/MS is of the quadruple focusing type, however, and this reduces the device cost at the initial stage and shortens the time for operators to acquire the skills of maintenance and operation. Though the quadruple focusing type is inferior to the double focusing type in sensitivity, the shortcoming is compensated for by massive specimen injection using a PTV (programmable temperature vaporizer). The result of a JIS (Japanese Industrial Standard) method and the result of this newly developed method are found to agree excellently with each other. This method is simple and efficient, suitable for use in the analysis of small incinerator flue gas. (NEDO)

  6. Fiscal 1998 joint promotion basic research report. Energy saving project for Achinsk refinery in Russia; 1998 nendo kyodo jisshi nado suishin kiso chosa. Roshia Achinsuku seiyujo shoene project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For prevention of global warming by greenhouse effect gas, study was made on energy saving measures for Achinsk refinery in Russia. Achinsk refinery is a relatively new plant put into operation in 1983, however, because of no various equipment for use combustion heat effectively, its average thermal efficiency is as low as 60%-70%, resulting in fuel consumption more than necessary one. Based on the study result, the following remodeling designs were made: Improvement of a heat exchange efficiency by relocation of heat exchangers to reduce fuel consumption of a heating furnace as much as possible, conversion of an existing heating furnace based on an old design concept to an advanced one, installation of a waste heat recovery system including a preheating convection unit and air preheater, reinforcement of heating furnace wall insulator, installation of an optimum control system for furnace operation, and improvement of a fuel supply system efficiency. This design showed possible reduction of heating furnace load, and possible furnace thermal efficiency of 90%. (NEDO)

  7. Survey on Pacific area energy policies by information collection. Laos and Myanmar; Taiheiyo energy seisaku joho nado genchi shushu chosa. Laos, Myanmar

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For planning the Pacific area energy policy of Japan, the field survey on energy situations was carried out in Laos and Myanmar. Since Laos is rich in hydraulic resources, the future electric power development is expected. Development of oil and coal resources is yet in a planning stage. Electricite du Laos (EdL) is in charge of electricity business, and its power generation capacity amounts to 220MW (including hydroelectric one of 93%), and a half of it is exported. Based on the predicted growth rate of 9%/y for domestic power demand, development of the capacity to 440MW by fiscal 2002 is scheduled. Myanmar has natural gas and various mineral resources, and is rich in hydroelectric resources. Myanmar Electric Power Enterprise (MEPE) is in charge of electricity business. The power generation capacity amounts to 1.34GW (including private one of 26%). The power generation facility is composed of gas turbine one of 53% and hydroelectric one of 33%. Based on the predicted growth rate of 11.5%/y for domestic power demand, development of the capacity to 1.6GW by 2001 is scheduled. For the present, conversion of previous gas-firing power plants to efficient combined cycle ones is a main issue. 21 figs., 43 tabs.

  8. FY1998 research report on the R and D on recycling technology. Part 1; 1998 nendo recycle nado kankyo gijutsu kekyu kaihatsu seika hokokusho. 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project aims to develop recycling technology for reduction of environmental burden caused by waste, and promotion of recycling of wastes. As for advanced recycling technology for PET bottles, the facility was improved for improvement of a facility operability and product quality. Study was made on the effect of a raw bale quality and recycled flake colors on a product quality, the forming test with PS or PET labels, and the concentration and effect of washing liquid circulated in flake washing process. As for recycling technology of hard-to-dispose waste plastics, facility improvement and demonstration test were made for continuous operation of dry-distillation/gasification of shredder dusts and separation of nonferrous metals and glass. Study was also made on pulverizing and recycling technologies of FRP bath tubs, and such pulverization costs were estimated. As for production technology of chemical feed and fuel from wastes, study was made on removal technology of non-flammable substances, development of alkaline additives, reacting condition, development of reactors, and use technology as chemical feed. (NEDO)

  9. Project report on drawing district energy-saving visions for Town of Nishi Senboku; Nishi Senboku machi sho energy vision sakutei nado jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Studied in this project are concrete energy-saving procedures, and potentially saved energy and abated CO2 emissions in Town of Nishi Senboku, to promote energy saving and abatement of gas emissions which cause global warming. The energy-saving procedures studied include co-generation, utilization of waste heat, wind power generation, utilization of low-temperature heat by snow, fuel-efficient vehicles, use of insulators for houses, energy-saving type electric appliances, energy-saving activities, and eco-driving. The results indicate that the energy-saving activities and eco-driving can potentially more contribute to energy saving than the others. The study on introduction of energy-saving facilities in the 'Nukumori Hot Spring/Umeria' project indicates that the heat pump plus co-generation case is the most advantageous, because it can potentially reduce primary energy by 2,845,215MJ/y and CO2 emissions by 22,688kg-C/y. Introduction of energy-saving facilities is also studied for an information center in the Nishi-Senboku service area for the Akita Highway. The results indicate that the introduction can potentially reduce primary energy and CO2 emissions by 25 and 13%, respectively. (NEDO)

  10. Fiscal 2000 survey report on regional new energy vision formulation for Oki town; 2000 nendo Okicho chiiki shin energy vision sakutei nado chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    Efforts are in progress to build a resource circulation type town symbiotic with natural environments at Oki town, Fukuoka Prefecture, which is an agricultural community where creeks run in every direction. A new energy vision has been worked out for the town, which centers about a plan for building a resource circulation type community. The survey results are summarized in six chapters dealing with (1) the survey outline, (2) local conditions relative to energy, (3) energy supply/demand structure, (4) amount of new energy in existence, (5) records and analysis of inhabitants' approach to energy conservation, and (6) a new energy introduction plan. The new energy introduction plan consists of four items involving a short term plan or a key project, a project for medium/long term surveys or feasibility study for the commercialization of new energy, plans for reducing energy consumption, and so forth. Discussed in relation to the short term plan are the introduction of photovoltaic power generation into public facilities, installation of a photovoltaic power station to be jointly utilized by the inhabitants, establishment of a grant system for the installation of solar water heaters for domestic use, creation of an additional subsidy system for domestic photovoltaic power generation, and the like. (NEDO)

  11. Fiscal 2000 report on regional new energy vision formulation project for Yunomae town, Kumamoto prefecture; 2000 nendo Yunomaecho chiiki shin energy vision sakutei nado jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A regional new energy vision has been formulated for Yunomae town, Kumamoto Prefecture, from the standpoint that local autonomies are required to work out measures compatible with Government energy policies and thereby to wrestle with environmental measures being undertaken across the world. The results of activities conducted for this purposed are stated in six chapters, which cover (1) the meaning of regional new energy vision formulation and its position, (2) outline of Yunomae town, (3) energy and environments, (4) energy situation in Yunomae town, (5) Yunomae town's regional new energy vision, and (6) plans for promoting the embodiment of the vision. In chapter (5), basic policies toward new energy utilization, overall plan, leading projects, and energy conservation measures are stated. The types of new energy taken up for discussion are photovoltaic power, wind power, biomass power, refuse-derived energy, and hydraulic energy. Projects are subjected to study, which relate to photovoltaic power generation, solar heat utilization, small scale hydroelectric power, small scale wind power, and the introduction of clean energy vehicles. It is expected that these projects when carried out will cover approximately 10% of the current energy consumption of the town. (NEDO)

  12. Driver`s behavior and the motion of motorized wheelchair when driving over rough surfaces; Dansa nado fuseichi sokoji no dendo kurumaisu no undo to join no kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Enomoto, A; Yokomori, M; Yamaguchi, S [Meijo University, Aichi (Japan)

    1997-10-01

    We analyzed about the motion of motorized wheelchairs and the driver`s behavior when passing over the small obstacles in place of the rough surface road or the gateway of house and road by experiment. The tested two type wheelchairs are the front wheel drive and the rear wheel drive. The lean angle of head and the pulse rate of driver, the feeling for stability and the yaw angle and the roll angle of the wheelchair bodies, and the deflection angle of front wheels of rear drive. 4 refs., 11 figs., 1 tab.

  13. Fiscal 1995 verification survey of geothermal exploration technology. Report on a deep geothermal resource survey; 1995 nendo chinetsu tansa gijutsu nado kensho chosa. Shinbu chinetsu shigen hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    For the purpose of reducing the risk of deep geothermal resource development, the paper investigated three factors for the formation of geothermal resource in the deep underground, that is, heat supply from heat source, supply of geothermal fluids, and the developmental status of fracture systems forming reservoir structures. The survey further clarified the status of existence of deep geothermal resource and the whole image of the geothermal system including shallow geothermal energy in order to research/study usability of deep geothermal resource. In the deep geothermal resource survey, drilling/examination were made of a deep geothermal exploration well (`WD-1,` target depth: approximately 3,000-4,000m) in the already developed area, with the aim of making rationalized promotion of the geothermal development. And the status of existence of deep geothermal resource and the whole image of the geothermal system were clarified to investigate/study usability of the geothermal system. In fiscal 1995, `WD-1` in the Kakkonda area reached a depth of 3,729m. By this, surveys were made to grasp the whole image of the shallow-deep geothermal system and to obtain basic data for researching usability of deep geothermal resource. 22 refs., 531 figs., 136 tabs.

  14. FY 1997 report on the field survey on country situations including efficient energy consumption. Vietnam; 1997 nendo chosa hokokusho (energy shohi koritsuka nado chiiki josei genchi chosa). Vietnam

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Field survey was made on the current state of and issues on energy in Vietnam. In Vietnam, firewood is in wide use as non-commercial energy, and sums to a half of total energy consumption. Other energies such as hydroelectric power, petroleum, natural gas and coal are self-sustainable. Commercial energy consumption in 1995 is estimated at 10,070,000t in oil equivalent, which is broken down into 23% for coal, 42% in oil, 5% for natural gas and 30% for electricity. Abundant water resources will form the mainstay of future electric power supply. Commercial production of oil started in 1986 becoming an oil exporting country. Several promising natural gas fields were discovered as the result of the exploration by foreign capital. Coal deposits are estimated to be nearly 3.5 billion tons, and most of them are anthracite. Electric power demand is growing at a higher rate than the economic growth of Vietnam. The growth rate of electric power demand is set to be 1.3 times that of GDP. Since construction funds for new plants cannot be satisfied with the national budget and domestic investment alone, the country is expecting foreign capitals. 21 figs., 36 tabs.

  15. Report on technological trend survey in fiscal 2000. Survey on bio-technology development strategy; 2000 nendo gijutsu doko nado chosa hokokusho. Bio technology gijutsu kaihatsu senryaku chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Survey and research have been performed on bio-technologies as to their seeds of technological development projects to be worked on by the government from the viewpoint of industrial utilization technologies. In the survey on the trends of research and development and technological development on human-genomes, the survey has been done on the status of execution in the Millennium Genome Project, and how the works related to human-genomes are done at the bio-related government based research organizations and the private sector research organizations. Trends related to the human-genome research in overseas countries were also surveyed. With regard to the future prospect of research and development in the post genome age, discussions were given on the result of the questionnaire survey on opinion leaders in the industrial, governmental and academic areas. In discussing the viewpoint of the industrial utilization technologies related to human genomes, candidates assumed usable in the genome related application fields were discussed, and a basic framework of a technological map was prepared. Based on the results thereof, the technological development areas anticipated to be important in the future were extracted, and the technological development themes were discussed. (NEDO)

  16. Report on `Survey of commercialization of intellectual ownership such as patent rights`; `Tokkyoken nado chiteki shoyuken no jitsuyoka ni kansuru chosa` hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A survey was conducted on research results in industrial circles, universities, etc. in the U.S., Europe and Japan, especially the state of how intellectual ownership such as patent rights is handled and the present situation of the commercialization of intellectual ownership, proposing problems and measures to be taken for promotion of practical use of excellent research results in Japan. The most important thing obtained from the survey is that study jointly by industrial circles and universities in the U.S. and Europe is much more advancing than that in Japan and is firmly established not only in industrial circles, universities and national research institutes, but in the whole society, actually producing a lot of favorable results. For Japan to catch up with the U.S. and Europe, needed is not only accumulation of the ideas in the past, but drastic measures to be taken from a new point of view. Concretely, it was proposed that by belonging intellectual properties such as patent rights to universities/research institutes and transferring their disposal rights to them, royalties of licenses are given back to inventors as incentives, and that as a body promoting the transfer to the industrial circle, `management organization` to which private vitality is introduced is established in universities/research institutes in order to promote interconnection between the industrial circle and universities. 15 refs., 35 figs., 36 tabs.

  17. FY1998 report on the research on support for practical recycling technologies. Part 1; 1998 nendo recyle gijutsu nado jitsuyoka shien kenkyu seika hokokusho. 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project aims at development, demonstration and utilization of waste recycling technologies. This report summarizes the fiscal 1998 results. The test/demonstration plant for separation and removal of foreign materials was constructed for effective use of waste building wood, and its optimum operation condition was studied. Although some foreign materials exists, 90% of waste building wood chips were separated and recovered through some improvements for the plant. An advanced separation technology is expected. As for fibering technology, fibers with target compression strength were obtained from cedar chips through a disintegration experiment using a newly developed refiner plate. Although the compression strength of fibers obtained from waste building wood chips was slightly poor, it is attained by increasing the target specific gravity of light- weight wooden materials by nearly 10% from 0.1. As for fiber orientation technology, as the tension of a forming belt was adjusted to achieve sufficient width compression, nearly 90% of the target compression strength was attained. A width compression method remains to be solved. (NEDO)

  18. FY 2000 report on the survey of the stabilization of wind power generation power system, etc.; 2000 nendo furyoku hatsuden denryoku keito anteika nado chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of elucidating effects of output fluctuations at the time of quantity introduction of wind power generation, conducted were observation of wind characteristics in Hokkaido and analysis of the characteristics, estimation of fluctuations in wind power output, analysis of fluctuations in system frequency, etc. In the observation of wind characteristics, wind velocity/wind direction were measured at observation posts of 30 wind turbines installed at 16 sites in Hokkaido. Concerning the conversion into wind power output, 10 cases were selected such as the case of passage of low atmospheric pressure, etc., and the generator unit and wind firm were simulated in detail. In the estimation of wind power output, good agreement with the results estimated was confirmed at points very near to posts of observation of wind characteristics. As to the evaluation of effects of wind power generation to the system, power system frequencies were simulated using the models constructed and using capacity and kinds of frequency adjusted power source as parameter. As a result, it was indicated that there was a possibility of frequency's sharply fluctuating in case the surplus energy in frequency adjustment is reduced by fluctuations in demand and further in case wind power output is fluctuated. (NEDO)

  19. Fiscal 2000 report on regional new energy vision formulation project for Yoron town; 2000 nendo Yoroncho chiiki shin energy vision sakutei nado jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A regional new energy vision has been formulated for Yoron town, Kagoshima Prefecture, which will serve as guidelines for building an Environmentally Friendly Island. Yoron town is a town of approximately 6,000 inhabitants as of fiscal 2000, its energy consumption is equivalent to 61,427 drums in terms of crude oil, and it receives electric power from Yoron Power Plant of Kyushu Electric Power Co., Inc. The results of activities conducted in this connection are summarized in seven chapters, which are (1) coping with new energy vision formulation (2), energy supply and demand, (3) estimation of existing amount of new energy, (4) basic policy toward new energy introduction, (5) projects for introducing new energy, (6) existing energy systems, and (7) reference materials. Named as projects are the construction of a water supply power source (for storage pump) for the Furusato district; power source for farmland irrigation pumps; power sources for the integrated sports park and municipal library; power source for a farmyard compost center; wind power, photovoltaic power, and combined power generation facilities for streetlights; and the utilization of bagasse. (NEDO)

  20. Report for fiscal 2000 on establishment of new energy vision in Fujino Town; 2000 nendo Fujino chiiki shin energy vision sakutei nado hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective to show specifically the efforts of working on new energies in Fujino Town in Kanagawa Prefecture, the existence quantity of new energies centering on the sun and woods was made clear to discuss the possibilities of utilizing them. Furthermore, investigations were performed on the energy demand and supply structure and possibilities of introducing new energies, and the specific new energy introduction plan was established. The activity achievements were put into order by the following six items: 1) the basic conception of the new energy vision, 2) various conditions of Fujino Town related to new energies, 3) energy demand and supply structure, 4) utilizable quantity of new energies, 5) toward the introduction of new energies, and 6) specific new energy facilities to discuss the introduction. Item 6 includes facilities to be built by defining model areas, facilities to discuss the full-swing introduction into facilities managed by the township, facilities to be discussed of full-swing introduction and to be composed in relation with the overall plan including large size hot water supply devices used at the spa, firewood boilers, a heat recovery system, and a large-scale photovoltaic power generation system. (NEDO)

  1. Report on regional new energy vision formulation project for Kahoku town, Kumamoto Prefecture; Kahokucho chiiki shin energy vision sakutei nado jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A regional new energy vision has been formulated for Kahoku town, Kumamoto Prefecture, for the realization of an energy resource circulation type regional community in which people earnestly strive to be symbiotic with nature. The results of related activities are shown in six chapters, which are (1) the prerequisites to the plan, (2) outline of the Kahoku town region, (3) surveys of the existing amount and expectedly available amount of new energy, (4) feasibility of new energy introduction, (5) assessment of new energy introduction plans and their effect, and (6) tasks to discharge, and policies to follow, for new energy introduction. In chapter (5), new energy introduction plans and introduction policies are shown. Plans are made for the incorporation of photovoltaic power facilities, small hydroelectric power facilities, and bamboo chip boilers into public facilities; the installation of 750 kW class wind power facilities; and the adoption of hybrid vehicles to serve as official special vehicles. It is expected that these plans when implemented will bring about a 1,400 t-c/year reduction in CO2 emissions. As for the introduction of wind power generation, the dimensions are determined by taking into consideration the prerequisites to a NEDO (New Energy and Industrial Technology Development Organization) grant. (NEDO)

  2. FY1995 studies on surface structures and mechanism of photocatalytic action of semiconductor oxides; 1995 nendo handotai hikari shokubai no hyomen kozo seigyo to sayo kiko kaimei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Development of the semiconductor photocatalyst such as titanium dioxide is important for photo-energy conversion and purification of the environment. We make clear that the mechanism of the photocatalysis using a spectroscopic or physico-chemical methods, and we developed the new photocatalyst with the control of the surface area, porosity, infinitesimal content, and surface modification of the catalyst surface. Titanium dioxide thin film photocatalysts were prepared by the dip coating method. Surface structure of the thin film was formed by the aggregated TiO{sub 2} anatase particle, its size was around 5 nm. This thin films effectively oxidazed NO, its photocatalytic activity is higher than that of commercial photocatalyst. Metal oxide anchored TiO{sub 2} photocatalysts (RuO{sub 2}/TiO{sub 2}) were prepared by the co-precipitation method. Effective charge separation of the RuO{sub 2}/TiO{sub 2} were confirmed by the measurement of ESR. The RuO{sub 2}/TiO{sub 2} photocatalyst successfully reduced CO{sub 2} and preserved its activity for much longer period than metal loaded catalyst. Hybrid photofunctionalized material was prepared by anchoring porphyrin moieties on the titanium dioxide surface. The relative quantum yield of electron transfer from porphyrin to the titanium dioxide conduction band has been markedly increased by water treatment of quanternized porphyrin-titanium dioxide covalently linked systems owing to removal of adsorbed porphyrin domains. (NEDO)

  3. Optimization of dynamic source depth for seismic surveys. Part 7; Dynamite shingen no hasshin shindo no saitekika ni tsuite (hyoso kozo no suitei (kusssetsuho jishin tansa oyobi denki denjiho tansa)). 7

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, H; Murayama, R; Mitsuhata, Y; Ishikawa, H [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1996-05-01

    For the improvement of quality of data collected by reflection aided seismic exploration using dynamite as the seismic source, information has to be collected about the surface layer structure before the charge depth is determined. For this purpose, refraction, electric, and electromagnetic exploration methods were tried. In the refraction method, an impactor was used as the seismic source. In the records, the surface wave prevails because vibration was generated on the surface. Analysis was made by the use of the initial travel time tomography. In the electric exploration, a double pole array was used to measure resistivity. The measured data was subjected to a fully automatic inversion for analysis. As the result, it was disclosed that it was useful to know the deep-level structure directly by use of tomographic methods in refraction seismic exploration so as to find the optimum charge level. Furthermore, about the electric and electromagnetic exploration techniques, it was found that these methods can be applied making use of resistivity to the evaluation of groundwater saturation. 7 refs., 5 figs., 3 tabs.

  4. Convenient method for estimating underground s-wave velocity structure utilizing horizontal and vertical components microtremor spectral ratio; Bido no suiheido/jogedo supekutoru hi wo riyoshita kan`i chika s ha sokudo kozo suiteiho

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, H; Yoshioka, M; Saito, T [Iwate University, Iwate (Japan). Faculty of Engineering

    1996-05-01

    Studies were conducted about the method of estimating the underground S-wave velocity structure by inversion making use of the horizontal/vertical motion spectral ratio of microtremors. For this purpose, a dynamo-electric velocity type seismograph was used, capable of processing the east-west, north-south, and vertical components integratedly. For the purpose of sampling the Rayleigh wave spectral ratio, one out of all the azimuths was chosen, whose horizontal motion had a high Fourier frequency component coherency with the vertical motions. For the estimation of the underground S-wave velocity structure, parameters (P-wave velocity, S-wave velocity, density, and layer thickness) were determined from the minimum residual sum of squares involving the observed microtremor spectral ratio and the theoretical value calculated by use of a model structure. The known boring data was utilized for the study of the S-wave velocity in the top layer, and it was determined using an S-wave velocity estimation formula for the Morioka area constructed using the N-value, depth, and geological classification. It was found that the optimum S-wave velocity structure even below the top layer well reflects the S-wave velocity obtained by the estimation formula. 5 refs., 6 figs.

  5. Estimation of shallow ground structure using short-period microtremors array observation. Results in Morioka area; Tanshuki bido no array kansoku ni yoru senbu chika kozo no suitei. Moriokashiiki ni okeru kekka

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, H; Obuchi, T; Saito, T; Iwamoto, K [Iwate University, Iwate (Japan). Faculty of Engineering; Yoshida, Y [OYO Corp., Tokyo (Japan)

    1996-05-01

    The velocity structure in the shallow ground structure was evaluated by observing microtremors of 1-10Hz in the Morioka City area. Plural wave sections free of vehicle noises or the like were selected out of the collected microtremor records, and the Fourier spectrum and coherence were calculated. Records sufficiently supporting the correlation between seismographs were chosen for the analysis. The phase velocity was calculated for each observation spot from plural array records by use of the F-K spectrum. The underground velocity structure was estimated by the inversion process using the matrix method. In this method, an early model was built on the basis of the observed phase velocity and the optimum underground velocity structure was determined by alternately performing two inversion processes: one for the case wherein the S-wave velocity is the sole parameter and the other for the case wherein the layer thickness is the sole parameter. As the result, a shallow underground velocity structure, which has good agreement with the available boring data in the Morioka City area, was successfully estimated, verifying the validity of this method. 4 refs., 7 figs.

  6. On the fault system and basement structure in and around the epicentral region of the 1995 Hyogo-ken Nanbu earthquake; 1995 nen Hyogoken nanbu jishin shingen shuhen no danso kiso kozo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Yokokura, T; Kano, N; Yamaguchi, K; Miyazaki, T [Geological Survey of Japan, Tsukuba (Japan); Ikawa, T; Ota, Y; Kawanaka, T [Japex Jeoscience Institute, Tokyo (Japan)

    1996-05-01

    A reflection elastic wave seismic survey was carried out as part of the emergency survey of active faults in relation with the Hyogo-ken Nanbu Earthquake. This paper presents an interim report on the survey covering a wide area with deep structure as the survey object. The paper mentions that processing the survey data has been nearly completed, and is in the stage of making analyses and interpretations of the result of the processing, and that the survey was an attempt of making a unified survey over land areas, shallow sea areas, and seas by setting twelve traverse lines in and around the epicenter region. The paper also introduces briefly what has been found on hypocenters used, vibration receivers, vibration intervals, and CPD intervals, and on shapes of faults, particularly the continuity (the relationship of the Ashiya fault, Koyo fault and Osaka bay fault with the above two faults, branching of the Osaka bay fault, faults between the Wada promontory fault, Awaji Island and the Osaka bay fault, the fault off the east coast at the central part of Awaji Island, the Shichiku fault on the west coast of Awaji Island, and the basement fault). Mention is given also on the basement structure chart of the Osaka bay prepared preliminarily for the purpose of reference. 2 figs.

  7. Fiscal 1999 geothermal development promotion survey. Structural boring survey work and analysis report (No.B-6 - Tsujinodake area); 1999 nendo chinetsu kaihatsu sokushin chosa. Kozo shisui chosa koji oyobi kaiseki hokokusho (No.B-6 Tsujinodake chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-12-01

    Cuttings from bores N11-TD-2 and N11-TD-3 drilled for the purpose of confirming the existence of geothermal resources in the Tsujinodake area were examined and tested, and the results of temperature logging, electrical logging, and water injection tests carried out during the structural boring work were analyzed. Activities were conducted in the four fields of (1) test boring work, (2) survey and measurement, (3) core cutting examination, and (4) comprehensive analysis. In bore N11-TD-2 positioned in the northern part of Tsujinodake, a sharp temperature rise was detected in the clay converted alteration zone between 200m above sea level and 200m below sea level. A high temperature of 215 degrees C was recorded at 200m below sea level, and it was found that high temperature geothermal water was in reserve at the bottom of the clay converted alteration zone between 100m above sea level and 200m below sea level. In bore N11-TD-3 in the southern wall of the Ata caldera, a convection type low temperature profile was observed at a shallow level and low temperature convection of underground water was detected there. (NEDO)

  8. FY 1997 report on the study on the formation condition of hetero-structure of single-crystalline semiconductor thin films; 1997 nendo chosa hokokusho (tankessho no handotai usumaku hetero kozo no keisei joken ni kansuru kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Since ion implantation causes material degradation by formation of crystalline defects, and hydrogen embrittlement deteriorates material strength, reduction of such defects has been positively studied. Study was made on a new active application of hydrogen separation into ion implantation defects. After H ion implantation of a proper depth into single-crystalline Si and SiC and successive annealing, single-crystalline films of sub-micron to several micron thick were obtained by hydrogen-induced delamination at the implantation depth due to hydrogen embrittlement in crystalline defects. The implantation depth is dependent on implantation energy. H atom forms (111) face defect through connection with dangling bond of crystalline defects. This crystal face defect forms a delamination plane through (100) face cleavage. This hydrogen embrittlement delamination by ion implantation is applicable to production of light-weight high-efficiency single-crystalline Si solar cells, and large single-crystalline SiC wafers as new resource saving process. 33 refs., 19 figs., 2 tabs.

  9. Acoustic excitation of diffusion flames with coherent structure in a plane shear layer.; Effects of acoustic excitation on combustion properties; Soshiki kozo wo tomonau sendan kakusan kaen no onkyo reiki.; Onkyo reiki ni yoru nensho tokusei no henka

    Energy Technology Data Exchange (ETDEWEB)

    Ishino, Y.; Kojima, T.; Oiwa, N.; Yamaguchi, S. [Nagoya Institute of Technology, Nagoya (Japan)

    1993-10-25

    This paper reports on experiments for acoustic excitation of plane shear structured flame. Flows of air separated into the higher velocity side and the lower velocity side by a partition on the center of a flow path merge at the measuring point to form a mixed layer with coherent structure. Fuel is supplied to this mixed layer with the flows so adjusted that the generated flame will attach to the partition on the lower velocity side. Acoustic excitation (at a sound pressure level of 100 dB to 120 dB) is performed in a speaker fitted on a wall on the higher velocity side. The paper mentions the results of the experiments as follows: the acoustic excitation produces such changes to diffusion flame in the plane shear layer as shorter flame and blue flame combustion and clarification of flame structures; as seen from spectral characteristics of temperature change in the flames, a flame acoustically excited strongly presents remarkable improvements in periodicity of the structure; as seen from sound pressure distribution in the flow direction at the measuring point, the flame zone of the flame acoustically excited strongly is positioned at the middle of the node and loop of a standing wave. 6 refs., 9 figs., 1 tab.

  10. FY 1999 report on the results of the research cooperative project on the research cooperation in promotion of reforming the structure of the Asian economy; 1999 nendo Asia keizai kozo kaikaku sokushin kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    This project aims at making the best possible of vitality of private companies in Asia, producing the technical results which directly connect to commercialization in a short term, and leading them to reinforcement of developmental ability of their own technologies in the country. In the first fiscal year, eight projects were carried out in five ASEAN countries, and the developmental results with high potential of commercialization were obtained. The names of project are as follows: 1) development of Thai material type seasoning (Thailand), 2) development of electronic ceramics sintering technology by the domestic production (Thailand), 3) study of small-/medium-scale activated coal production technology for depopulated areas in Indonesia (Indonesia), 4) development of a fiber material procurement supply chain management system connecting among Asian countries by Web, 5) development of large plastic formed products adopting gas injection blow molding method (The Philippines), 6) joint R and D on the increase in power transmission capacity using the existing overhead transmission line in Malaysia, 7) development of local site application type asbesto substituting construction materials (Vietnam), 8) low temperature storing technology for Japanese species rice produced in Vietnam (Vietnam). All the projects were proposed by Japanese companies. (NEDO)

  11. Joint stiffness identification of body structure using neural network. Jointed part composed of 2 beams; Neural network ni yoru shatai kozo no ketsugo gosei dotei. Buzai 2 hon kara naru ketsugobu no baai

    Energy Technology Data Exchange (ETDEWEB)

    Okabe, A; Tomioka, N [Nihon University, Tokyo (Japan)

    1997-10-01

    The method to obtain a joint stiffness value from displacements of jointed part using hierarchical neural networks in case of a jointed part composed of two beams were proposed. First, the sample data of displacements of jointed part vs. joint stiffness are prepared as learned data. Second, the relations between displacements of jointed part and joint stiffness are constructed from these learned data using a hierarchical neural networks. It was found that the value of joint stiffness can be obtained from displacement of jointed part by the trained neural network. 4 refs., 9 figs., 2 tabs.

  12. Fiscal 1999 geothermal development promotion survey report. Structural boring survey work and analysis (No. B-5 - Musadake region); 1999 nendo chinetsu kaihatsu sokushin chosa. Kozo shisui chosa koji oyobi kaiseki hokokusho - No. B-5 Musadake chiiki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-12-01

    For geothermal development in the Musadake region, Shibetsu-gun, Hokkaido, structural boring was carried out and boreholes were inspected. In the structural boring survey, borehole N11-MD-3 was drilled as deep as 2,001.18 m, and borehole N11-MD-4 2001.44 m. Performed or tested for each of the two boreholes were temperature logging, electrical logging, temperature recovery, reinjection, core cutting examination, and so forth. The result of the temperature logging shows that temperature rise is slower at levels deeper than 1280 m in borehole N11-MD-3, with the maximum temperature marking 274 degrees C, and, in borehole N11-MD-4, the maximum temperature is 198 degrees C. No reinjection test is carried out because the ground pressure is too high to allow the replacement of the borehole content with fresh water. Analysis results lead to a conclusion that the hot fluid in this region originates in fossil seawater and in meteoric water, the latter arriving after a long-term permeation process, heated by thermal conduction to 270 degrees C or higher. It is inferred that the geothermal fluid flows in a fissure in the vicinity of the Musadake/Mt. Shitabanupuri fault and a fault orthogonally crossing the said fault for the formation of a high-temperature geothermal storage. (NEDO)

  13. FY 1998 Report on development project of structural residence of the next generation. Attachment 4. Frame analysis system manual; 1998 nendo jisedai kozo jutaku kaihatsu jigyo shiryohen. 4. Kako kaiseki system manual

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Attachment 4 of the FY 1998 report on development project of structural residence of the next generation describes the frame analysis system manual. NAPISOS is a program for analyzing static and dynamic responses of three-dimensional structures. The dynamic response is calculated by numerical integration in the time region. Dynamic load can handle dynamic exciting force, uniform seismic input and forced displacement at a node, and analyze linear elasticity and non-linear properties. The static load can handle nodal force, static seismic coefficient and forced displacement at a node, and analyze linear elasticity and non-linear properties. The static analysis also can perform analysis based on the time history response displacement method as the special case. The program implementation procedures fall into 4 general steps; first: inputting/processing of structural data, second: eigen value analysis or equivalent nodal force calculation, third: response calculation by direct integration, preparation of equivalent damping matrix or pre-stress analysis, and fourth: outputting the results. The input data related to control, structure and load are also described. (NEDO)

  14. Investigations in fiscal 1986 on promotion of geothermal development. Part 2. Report on precision structural test well drilling and investigation works in Otaki area; 1986 nendo chinetsu kaihatsu sokushin chosa hokokusho. 2. Otaki chiiki seimitsu kozo shisui oyobi chosa koji

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-09-01

    With an objective of promotion of geothermal development in the Otaki area in Nagano Prefecture, precision structural test well drilling and investigation works have been carried out, and the result thereof reported. The investigated area is an inclined land with an area of 70 km{sup 2} at altitudes of 1,000 to 2,000 m in the southern foot of the Mitake volcano having Otaki River as the southern border. The investigation has performed during the period from March 2 to September 30, 1987 the drilling of the N61-OT-5 test well hole (depth of 502.0 m), temperature logging, temperature restoration test, water injection test, and core test. The result of the investigation may be summarized as follows: existence of the stratigraphic succession as predicted by ground surface investigation, and existence of the Mesozoic and Palaeozoic strata of the Mino belt were verified; the Mesozoic and Palaeozoic strata of the Mino belt being the base bed have only small cracks, and very little alteration can be identified; X-ray diffraction of powder from test drilled cores recognized very little minerals altered by hot water; and the temperature logging and temperature restoration test identified no temperature indication that clearly indicates existence of heat sources. As a conclusion, there is no alteration due to hot water down to 500 m below the surface in the vicinity of the investigation well, and the possibility of a geothermal reservoir to exist is extremely low. (NEDO)

  15. Research and development of photovoltaic power system. Study on structural defects in silicon-based amorphous materials; Taiyoko hatsuden system no kenkyu kaihatsu. Amorphous silicon kei zairyo no kozo kekkan ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, T [Kanazawa University, Ishikawa (Japan). Faculty of Engineering

    1994-12-01

    Described herein are the results of the FY1994 research program for structural defects of silicon-based amorphous materials for solar cells. The study on light generation defects of the a-Si:H system and rejuvenation process by annealing establishes the effects of light irradiation time on changed neutral dangling bond density as a result of light irradiation at varying temperature of 77K, room temperature and 393K. The study on annealing to rejuvenate light generation defects of various types of a-Si-H systems establishes the activation energy distribution with respect to annealing to remove light-induced defects, showing that hydrogen affects the distribution of light-induced defects. The study on decaying process of light-induced ESR for undoped and N-doped a-Si:H systems observes the decaying process of light-induced ESR, after light is cut off, extending for a period of several seconds to several hours at 77K for the a-Si-H systems containing N in a range from 0 to 12at%. The other results presented are space distribution of neutral defects of light-irradiated a-Si-H systems, and rejuvenation process of light-induced spin for the a-Si(1-x)N(x):H composition. 6 figs.

  16. FY 1974 Report on results of Sunshine Project. Research and development of methods for wide-area thermal structure exploitation; 1974 nendo koiki netsu kozo chosaho no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-05-28

    The project of (research and development of methods for wide-area thermal structure exploitation) is to pursue (1) development of heat flow rate analyzers, and researches on the methods for measurement/analysis of heat flow rates, (2) researches on geological thermometers with the cores collected from test bores as the samples, (3) observation/analysis of microearthquakes, and application of the results to the geothermal structure exploitation, and (4) development, on a trial basis, small, light air drilling machines. The method for clearly elucidating thermal structures has not been well established. Therefore, a test bore was drilled to measure temperature and collect the core samples in the wide-area geothermal district at Kita Yahata-daira as the model district, for measurement of heat flows, and analysis of the cores to estimate temperature at which they are formed. Microearthquakes, which frequently occur in geothermal areas, are also observed for extended periods. This project of (research and development of methods for wide-area thermal structure exploitation) is aimed at, based on the above efforts, to estimate/elucidate depth of thermal sources by the geological, geophysical and geochemical studies, relationships between geological structures and high-temperature zones, geothermal propagation structures, and geothermal reserves. This report summarizes the R and D results in the initial year of the 6-year plan. (NEDO)

  17. Investigation on the dynamic response and strength of very long floating structures by beam modeling on an elastic foundation; Dansei shishojo no hari model ni yoru chodai futai kozo no doteki tawami kyodo tokusei ni kansuru kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tsubogo, T.; Okada, H. [University of Osaka Prefecture, Osaka (Japan). Faculty of Engineering

    1997-08-01

    A very large floating structure was replaced with the beam on an elastic foundation to examine the response characteristics in waves. Another evidence was regularly and numerically given for the basic characteristics of a very large floating body Suzuki found. New information was also obtained. The frequency response is mainly classified into a wave number control area and proper frequency control area when buoyancy elasticity exists. When the buoyancy structure is long and flexible, the proper frequency becomes continuous and the frequency control area becomes a resonance area. In the wave number control area, the Suzuki`s characteristic wave number becomes a control parameter, and various characteristic values are indicated by characteristic wave numbers. The response in the wave number control area becomes quasi-static when the distribution mass of buoyancy is fully small. The design in which the distribution mass of buoyancy is fully large must be avoided. In the displacement amplitude, the mass on the free end is severest. The proper frequency of vertical vibration relatively moves to the high-frequency side when buoyancy is considered as an elastic foundation. Attention must be thus paid to the proper frequency of vibration on the horizontal surface. 9 refs., 12 figs., 3 tabs.

  18. Thermal structure of east and Southeast Asia. Comparison of results of Curie point depth analysis and heat flow data; Totonan Asia chiiki no ondo kozo. Curie ten shindo kaiseki kekka to chikaku netsu ryuryo tono hikaku

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, A; Okubo, Y; Matsubayashi, O [Geological Survey of Japan, Tsukuba (Japan)

    1997-10-22

    This paper describes the distribution of Curie point depth and its characteristics determined from the spectral analysis of magnetic anomaly data in East and Southeast Asia. It also describes relationships between the Curie point depth and the other geophysical information such as topography, heat flow data and tectonics. The Curie point depths are shallower than about 10 km at volcanic and geothermal areas, between 15 and 25 km at island arcs and back arc rifts, deeper than 20 km at continents, and deeper than 30 km at trenches. The Curie point depth (Dc) estimated from the heat flow data can be expressed by Dc=k{theta}c/q where k is thermal conductivity, q is heat flow, and {theta}c is Curie point. Based on the Curie point depths obtained from Curie point depth analysis in the cross section of northeast Japan and the averaged values of heat flow at individual points, they are distributed along a line of k{theta}c=1500[Wm{sup -1}]. Values of k{theta}c are small near the axis of Japan trench and large in the northeast Japan. It is considered that local anomalies can not be grasped from the spectral analysis. 21 refs., 3 figs.

  19. Distribution of strong ground motion from uppermost crustal structure. Comparison with disaster from the Hyogo-ken Nanbu Earthquake; Yaya fukai chika kozo no henka ni yoru kyoshindo bunpu. Hyogoken nanbu jishin ni yoru higai bunpu tono hikaku

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Z; Okubo, R [Kawasaki Geological Engineering Co. Ltd., Tokyo (Japan)

    1997-10-22

    It was intended to elucidate characteristics of distribution of damages caused by an earthquake which occurs directly below an urban area. Therefore, numerical simulation using the pseudo-spectral method was performed on characteristics of seismic wave propagation in non-homogenous media composed of rock beds and sediment beds, and of seismic wave amplitudes on ground surface. The simulation has utilized information on underground structures disclosed by using the latest physical exploration method. The underground structure model assumed a two-dimensional model hypothesizing presence of upper, middle and lower beds in the Osaka bed group on granite, using as reference the information on S-wave velocity underground structure revealed by the microtremor exploration method. With an objective to elucidate characteristics of distribution of collapse ratio in the area from 8-chome, Okamoto, Higashinada Ward, Kobe City to 2-chome of Sakanasaki Minamicho, as damages suffered from the Hyogo-ken Nanbu Earthquake, a simulation has been performed varying the structure model based on the results derived by the microtremor exploration method and the reflection method. As a result, it was shown that the characteristics of the maximum amplitude distribution of displacement of ground surface, velocity and acceleration agree well with those of the collapse ratio distribution, and that the simulation using the pseudo-spectral method is an effective means to analyze the ground surface collapse ratio distribution. 5 refs., 3 figs.

  20. Characterization of subsurface structure at Soultz HDR field by the triaxial drill-bit VSP; Sanjiku drill bit VSP ho ni yoru Soultz HDR field no chika kozo suitei

    Energy Technology Data Exchange (ETDEWEB)

    Asanuma, H; Niitsuma, H; Liu, H [Tohoku University, Sendai (Japan); Baria, R

    1997-10-22

    Triaxial drill-bit VSP (vertical seismic profiling) method is applied to the Soultz HDR (hot dry rock) field, France, where an artificial reservoir is provided inside the bedrock, and the structure inside the rockbed is estimated. An elastic wave detector is installed in the rockbed in this field, and data are acquired having frequency components up to approximately 1kHz. The trajectory of particles due to excavation noise is analyzed, and it is found that the drill-bit is the primary source of noise during excavation and that the SV-wave dominates in the emitted noise. Estimating the subsurface structure aided by the principle of the triaxial drill-bit VSP method, the lower part is detected of the artificial reservoir formed by hydraulic fracturing. As is reported in this paper, when the principle of the subject VSP method is considered, it has to be said that it is quite difficult to employ this method to extensively estimate the subsurface structure on the basis of measurements of the inside of the rockbed. There is a plan for a future study of a technique for accurately and extensively estimating subsurface structures by use of a small number of sensors. 8 refs., 7 figs.

  1. Estimation of a subsurface structure by using shallow seismic engineering exploration system with multiple function (SWS); Takino danseiha tansa sochi (SWS) ni yoru senbu chika kozo tansa ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Y [Beijing Shuidian Research Institute of Geophysical Surveying, Beijing (China); Ling, S [Nihon Nessui Corp., Tokyo (Japan); Okada, H [Hokkaido University, Sapporo (Japan)

    1997-10-22

    The Beijing Shuidian Research Institute of Geophysical Surveying has performed ocean seismic exploration in the area where the Fujian Pingtan bridge was planned to be constructed. The elastic wave exploration device is of a multi-functional type. The device has functions of acquiring, processing and analyzing data in seismic exploration using the reflection method, and can visualize subsurface conditions at the same time as performing the exploration. The planned bridge building area spans over a sea area of about 3500 m long with water depths from several meters to 30 meters. The foundation bed consists of dacite lithologic tuff and granodiorite. The seal level varies from 4.0 m to 4.8 m between high and low tides. According to the result of other measurements, the elastic wave propagation velocities of the sea water were found from 1475 to 1485 m/s, and the elastic wave propagation velocities at the surface bed of the sea bottom were from 1550 to 1700 m/s. The exploration used a workboat which moves at a constant speed while maintaining the offset between a transmitting source and a receiving source constant, executing vibration transmitting, receiving and recording all on the sea. The result of the exploration revealed that neither obstacles such as sunken ships nor marks of occurrence of ocean bottom landslides were present. 1 ref., 5 figs.

  2. Study on deep crustal resistivity structure using wideband magnetotellurics. In the case of eastern part of Hokkaido, Japan; Kotaiiki MT ho wo mochiita shinbu chikakuhi teiko kozo no kenkyu. Hokkaido Tobu chiiki ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Sato, H; Tanimoto, K; Maeda, T; Nishida, Y [Hokkaido University, Sapporo (Japan); Takada, M; Tamura, M [Hokkaido University, Sapporo (Japan). Research Center of Earthquake Prediction; Ogawa, Y [Geological Survey of Japan, Tsukuba (Japan); Nagao, T [Tokai Univ., Tokyo (Japan)

    1997-10-22

    Wide-range MT (magnetotelluric) observation is conducted to collect knowledge of the middle and lower parts of the crust of the above-named region, about which but a little information is available, for comparison with information about Kurile islands arc tectonics. Three traverse lines crossing the Kurile islands roughly in the north-south direction and two lines running from east to west are used, with the observation stations totalling 48. The distance between observation stations is 7-8km on the Nijibetsu line, and approximately 15km on the Nakashibetsu and Akan lines. A very wide frequency range of 320-0.0005Hz is used for measuring, and these results in detection with success of resistivity structure details from shallow to deep layers in the crust. The collected data are analyzed, and it is estimated that the northern and central parts have a high-low-high three-layer structure while the southern part has a low-high two-layer structure. Since the data obtained at observation stations at the middle of the lines, in particular, have an extremely low apparent value of several ohm/m at about 1Kz in the absence of splits in the TM (transverse magnetic) and TE (transverse electric) modes, it is inferred that the low-resistivity layer is considerably thick and is distributed rather uniformly. 13 refs., 5 figs.

  3. Formation of porous carbon materials from phenol-formaldehyde resin and their adsorption characteristics; Fenoru/horumu arudehido jushi kara erareta takosei tanso zairyo no kogeki kozo to sono kyuchaku tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Oda, H.; Tojo, R.; Nomura, A. [Kansai Univ., Osaka (Japan). Faculty of Engineering

    1997-05-15

    In this study, preparation of porous adsorbent with developed micro-pores and meso pores and open pores on the external surface is tried. Namely, PFR-sawdust activated carbon is produced by carbonizing the PFR-sawdust composite materials obtained by adding KOH-immersed wood powders in the preparation of phenol-formaldehyde resin(PFR). Additionally, as a comparative test, KOH is added directly into PFR and PFR-KOH activated carbon is prepared by carbonization. Simultaneously with the clarification of the difference of pore structure between said two kinds of activated carbons, a various kinds of adsorbing tests are carried out to evaluate the adsorbing effects thereof. PFR-KOH activated carbon having a high specific surface area of 3500 m{sup 2}/g and a large number of micro-pore and meso pores is extremely effective in absorption of gas phase while the yield and particle strength are low. PFR-sawdust has a specific surface area of 1500 m{sup 2}/g which is the same level of activated carbons on the market, but the yield thereof is twice as that of PFR-KOH. 9 refs., 5 figs., 3 tabs.

  4. Solubilization of meso-carbon microbeads by potassium- or dibutylzinc-promoted butylation and structural analysis of the butylated products; Mesocarbon microbeads no butyl ka ni yoru kayoka to erareta butyl kabutsu no kozo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Murata, S.; Zhang, Y.; Kidena, K.; Nomura, M. [Osaka University, Osaka (Japan). Faculty of Engineering

    1996-10-28

    Tetrahydrofuran (THF) solubility and structure of the butylated products of meso-carbon microbeads (MCMB) were studied experimentally. In experiment, MCMB-A and MCMB-B obtained from two kinds of coal-tar pitch were used as specimens. MCMBs were butylated by BZ method using dibutylzinc-butyl iodide and KT method using K-butyl iodide-THF, and the butylated products were successfully obtained. The butylated products were investigated through THF solubility test, {sup 13}C-NMR measurement and gel permeation chromatography (GPC) measurement. As the experimental result, a BZ method produced the butylated products at a yield of nearly 170%, while a KT method produced them at a yield of nearly 130%. The THF solubility was estimated to be 89-97%. As the study result of molecular weight distributions by GPC measurement of solvent solubles, the molecular weight of raw material MCMB was estimated to be 590-770 in terms of polystyrene. 6 refs., 2 figs., 1 tab.

  5. Thermal relaxation of bituminous coal to improve donation ability of hydrogen radicals in flash pyrolysis; Sekitan kozo kanwa ni yoru suiso radical kyoyo noryoku no kojo wo mezashita netsubunkai mae shori

    Energy Technology Data Exchange (ETDEWEB)

    Mori, T.; Isoda, T.; Kusakabe, K.; Morooka, S. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Hayashi, J. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology

    1996-10-28

    In terms of coal conversion reaction, the behavior of bituminous coal heated beyond a glass transition point was examined on the basis of pyrolyzed products, and the effect of an increase in proton mobility on promotion of coal decomposition was evaluated. In experiment, after Illinois bituminous coal specimen was heated up to a specific temperature in N2 or He gas flow at a rate of 5K/min, the specimen was directly transferred to a pyrolyzer for instantaneous pyrolysis. As the experimental result, the glass transition temperature of the Illinois coal specimen was calculated to be 589K from a differential scanning calorimetry (DSC) profile. From the pyrolysis result of the Illinois coal specimen heated up to 623K, the char yield decreased by 3kg as compared with that of the original coal, while the tar yield increased by 4kg up to 27kg per 100kg of the original coal. This tar increase was larger than that of cooled coal. These results suggested that the donation of hydrogen radicals to coal fragments is improved with an increase in proton mobility. 4 refs., 4 figs., 1 tab.

  6. Studies of initial stage in coal liquefaction. 4. Radical formation and structural change with thermal decomposition of coal; Ekika hanno no shoki katei ni kansuru kenkyu. 4. Netsubunkai ni tomonau radical seisei kyodo to kozo henka

    Energy Technology Data Exchange (ETDEWEB)

    Kanaji, M.; Kaneko, T.; Shimasaki, K. [Nippon Brown Coal Liquefaction Co. Ltd., Tokyo (Japan); Kumagai, H.; Chiba, T. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology

    1996-10-28

    In relation to coal liquefaction reaction, the effect of the coexistence of transferable hydrogen (TH) from process solvent on reduction of radical concentration and the effect of pre-heat treatment on average structure of coals were studied. In experiment, change in radical concentration with temperature rise was measured using the system composed of Yallourn coal and process solvent. The results are as follows. Process solvent with a wide boiling point range of 180-420{degree}C is effective in suppressing an increase in radical concentration even at higher temperature. The effect of hydrogen-donating solvent increases with TH. It was also suggested that high-boiling point constituents in solvent stabilize radicals even over 400{degree}C by vapor phase hydrogenation. The experimental results of pre-heat treatment are as follows. Although the conversion improvement effect of TH is equivalent to that of the model solvent, TH tends to produce soluble products with smaller ring numbers. It was thus suggested that pre-heat treatment in process solvent is effective to inhibit retrogressive reactions. 6 refs., 5 figs., 1 tab.

  7. Fiscal 1999 geothermal energy development promotion survey. Report on survey of structural boring (No. B-7 Kuwanosawa area); 1999 nendo chinetsu kaihatsu sokushin chosa. Kozo shisui chosa koji oyobi kaiseki hokokusho (No.B-7 Kuwanosawa chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    Borehole N11-KN-1 was digged and investigated for clarifying the geothermal structure of the Kuwanosawa area, with attention fully paid to the existing survey results. The hole is inclined, 1,802.30m deep in total, with a casing pipe installed down to the 1,101.76m level. Temperature was measured and electrical logging was performed at levels 410m, 1,110m, and 1,802.23m while the hole walls were still exposed bear. The maximum temperature of 161 degrees C was observed at the hole bottom, and the product of permeability - layer thickness transmission coefficient was described by 3.72 to 4.75 times 10{sup -1} darcy.m. The geothermal structures in presence in the south-western part of the survey area and along the Wasabizawa fault were made clear, and it was found that there exists no high-temperature water system in the vicinity of borehole N11-NK-1. As tasks for the future, it was proposed that a geothermal survey of the south-eastern part which includes borehole N57-YO-2 and a geochemical survey of fluids including hot spring water and surface be conducted. (NEDO)

  8. FY 1999 report on the results of the development of technology of super metal. Development of nano/amorphous structure control materials; 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Nano amorphous kozo seigyo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of reducing the amount of energy consumption of transportation equipment such as automobiles, the development is made of innovative metal materials enabling the weight reduction of members relatively on the basis of simple chemical components and by making more substantial improvement of characteristics such as strength and toughness than in the existing metals. For it, the following R and D are conducted in which nano crystal structure and non-equilibrium phase structure such as amorphous are controlled to the limits: 1) particle micro-dispersion technology; 2) high speed super plastic formation technology; 3) high density energy utilization control technology; 4) control cooling technology. In 1), study was made of alloy components and effects of the creation process which are needed for achievement of the nano level of crystal grain. In 2), conditions of vapor deposition and production in high speed particle deposition method are optimally selected, and amorphous and nano crystal structures can easily be produced. In 3), high corrosion-resistant amorphous alloy bulk materials with 5mm thickness and 10mm diameter were successfully trially manufactured. In 4), a bulk amorphous specimen with 10mm outer diameter, 6mm inner diameter and 1mm thickness which was fabricated in the forging method indicated favorable magnetic properties. A method to make a specimen which is more stable is being studied. (NEDO)

  9. On the calculation of scattered fields by 3-D structure in the time-domain electromagnetic (TDEM) method; Jikan ryoiki denjiho ni okeru sanjigen kozo kara no sanranba no keisan ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Murakami, Y [Geological Survey of Japan, Tsukuba (Japan); Saito, A; Oya, T [Mitsui Mineral Development Engineering Co. Ltd., Tokyo (Japan)

    1996-10-01

    This paper describes the calculation method of 3-D underground structures in TDME method which measures only field components. Recently, FDTD method was developed as calculation method in time domain difference calculus, and the forward analysis accuracy of 3-D fields was rapidly improved. The survey results using a large-scale loop (600m{times}360m) were numerically analyzed by FDTD method. 16 measuring lines were prepared in both X and Y directions, and measuring points were prepared on intersection points of the measuring lines. Since signal current is staircase one, step and impulse responses of the ground were determined by calculating magnetic field and its time differentiation. The rectangular body (120m{times}120m{times}100m) of 0.2S/m in conductivity (5 ohm m in resistivity) was installed 160m under the ground as 3-D resistivity anomaly. The ground of 0.01S/m (100 ohm m) was assumed. Time variation in horizontal magnetic field vector plot of impulse responses of the uniform ground could be observed. The position of the resistivity anomaly could be also determined from spacial differentiation of magnetic field of grid pattern measuring points. 1 ref., 6 figs.

  10. Fault-related-folding structures and reflection seismic sections. Study by seismic modeling and balanced cross section; Danso ga kaizaisuru shukyoku kozo no keitai to jishin tansa danmen. 2. Seismic modeling oyobi balanced cross section ni yoru study

    Energy Technology Data Exchange (ETDEWEB)

    Tamagawa, T; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan); Tsukui, R [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-05-27

    It occasionally happens that there exists a part where reflection near the thrust is not clearly observed in a thrust zone seismic survey cross section. For the effective interpretation of such an occurrence, the use of geological structures as well as the reflected pattern is effective. When the velocity structures for a fold structure having a listric fault caused anticline (unidirectionally inclined with a backlimb, without a forelimb) and for a fault propagation fold are involved, a wrong interpretation may be made since they look alike in reflection wave pattern despite their difference in geological structure. In the concept of balanced cross section, a check is performed, when the stratum after deformation is recovered to the time of deposition, as to whether the geologic stratum area is conserved without excess or shortage. An excess or shortage occurs if there is an error in the model, and this shows that the fault surface or fold structure is not correctly reflected. Positive application of geological knowledge is required in the processing and interpreting of data from a seismic survey. 6 refs., 6 figs.

  11. Fault-related-folding structure and reflection seismic sections. Construction of earth model using balanced cross section; Danso ga kaizaisuru shukyoku kozo no keitai to jishin tansa danmen. 1. Balanced cross section wo mochiita chika model no kochiku

    Energy Technology Data Exchange (ETDEWEB)

    Matsuoka, T; Tamagawa, T [Japan Petroleum Exploration Corp., Tokyo (Japan); Tsukui, R [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-05-27

    Pre-stacking depth migration treatment is studied for the estimation of the fold configuration from seismic survey cross sections. The estimation of a velocity structure is necessary for the execution of such treatment, and the utilization of structural-geological knowledge is required for its interpretation. The concept of balanced cross section in relation to the fault-bend fold constructs a stratum structure model under conditions that the deformation during fold and fault formation is a planar strain, that there is no change in volume due to deformation, and that a fold is a parallel fold. In addition to the above geometric and kinetic approach, there is another fold formation process simulation model using a Newtonian fluid for study from the viewpoint of dynamics. This simulation stands on the presumption that the boundary contains a ramp that had been in presence before fold formation and that an incompressible viscous matter is mounted on the top surface. The viscous matter flows and deforms for the formation of an anticline on the ramp. Such enables the reproduction of a fault-bend fold formation process, and helpful discussion may be furthered on the dynamic aspect of this simulation. 5 refs., 4 figs.

  12. Estimation of subsurface structures in a Minami Noshiro 3D seismic survey region by seismic-array observations of microtremors; Minami Noshiro sanjigen jishin tansa kuikinai no hyoso kozo ni tsuite. Bido no array kansoku ni yoru suitei

    Energy Technology Data Exchange (ETDEWEB)

    Okada, H; Ling, S; Ishikawa, K [Hokkaido University, Sapporo (Japan); Tsuburaya, Y; Minegishi, M [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-05-27

    Japan National Oil Corporation Technology Research Center has carried out experiments on the three-dimensional seismic survey method which is regarded as an effective means for petroleum exploration. The experiments were conducted at the Minami Noshiro area in Akita Prefecture. Seismometer arrays were developed in radii of 30 to 300 m at seven points in the three-dimensional seismic exploration region to observe microtremors. The purpose is to estimate S-wave velocities from the ground surface to the foundation by using surface waves included in microtremors. Estimation of the surface bed structure is also included in the purpose since this is indispensable in seismic exploration using the reflection method. This paper reports results of the microtremor observations and the estimation on S-wave velocities (microtremor exploration). One or two kinds of arrays with different sizes composed of seven observation points per area were developed to observe microtremors independently. The important point in the result obtained in the present experiments is that a low velocity bed suggesting existence of faults was estimated. It will be necessary to repeat experiments and observations in the future to verify whether this microtremor exploration method has that much of exploration capability. For the time being, however, interest is addressed to considerations on comparison with the result of 3D experiments using the reflection method. 4 refs., 7 figs.

  13. Estimation of underground structures in the Osaka-Kobe area by array-network observations of microtremors; Bido no array kansoku ni yoru Osaka-Hyogo chiiki no chika kozo no suitei

    Energy Technology Data Exchange (ETDEWEB)

    Okada, H; Ishikawa, K; Ling, S [Hokkaido University, Sapporo (Japan); Sasabe, K [Ministry of Construction, Tokyo (Japan)

    1997-05-27

    Microtremor observations have been carried out with an objective to estimate underground structures including the foundation depth in the Osaka-Kobe area which has been greatly damaged by the Hyogoken-nanbu earthquake in 1995. Different organizations have made seismic surveys and boring investigations in this area, by which elucidation has been made on the underground structures. The present observations are intended to identify S-wave velocity distribution in a wide area from the ground surface to the foundation, which is difficult to be verified by using conventional surveys and investigations. Methods to detect surface waves which are contained in microtremors include the frequency-wave number method (the F-K method) and the spatial autocorrelation method (the SPAC method). The SPAC method can estimate phase velocities of longer waves for the size of an array than with the F-K method, and is more advantageous in estimating ground structures at greater depths. S-wave velocity structure was estimated down to the foundation rocks existing in depths of about 0.5 to 2.0 km. For estimating the phase velocities in Raleigh waves, the SPAC method and the expanded spatial autocorrelation method were used. The underground structures thus derived showed a good agreement with the results of explorations using other methods. 8 figs., 1 tab.

  14. Relationship between surface structure of silicon containing steel and adhesion of hot dip galvanized coating; Si gan'yu koban no hyomen kozo to yoyu aen mekki micchakuseino kankei

    Energy Technology Data Exchange (ETDEWEB)

    Tsuchiya, Y.; Hashimoto, S.; Ishibashi, Y. [Kokan Keisoku K.K., Kawasaki (Japan); Inagaki, J. [NKK Corp., Tokyo (Japan); Fukuda, Y. [Shuibuoka University, Shizuoka (Japan)

    2000-06-01

    The surface of the annealed steel and the exfoliated interface of the coating for the hot dip galvanized Si containing steel sheets was characterized by using SEM (Scanning Electron Microscope), AES (Auger Electron Spectroscopy) and TEM (Transmission Electron Microscopy). The adhesion of the coatings have depended on the Si content of the steel. It have been found that MnSiO{sub 3} particles are formed at the surface of the annealed steels having high Si content and that two types of grain having different distribution of the oxide exist in the steels. Large oxide particles have been formed in one type of grain and small particles are formed in the other type of grain. The different type of Fe-Zn alloy are formed on two types of grains. It have been observed that the oxide particles exist at the interface of exfoliated coatings after the adhesion test for the steels with high Si content. The distribution of the oxide particles observed at the bottom of the exfoliated coating is quite similar to that of the surface oxide of the annealed steel. From these results, the exfoliation of the coating has initiated at the oxide particles of the steel surface that has been not reduced during the hot dip galvanizing. (author)

  15. FY 1994 report on the survey of geothermal development promotion. Investigative construction and analysis for structural boring (No. A-1 - Haneyama area); 1994 nendo chinetsu kaihatsu sokushin chosa. Kozo shitsui chosakoji oyobi kaiseki hokokusho (No. A-1 Haneyama chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-08-01

    For the contribution to elucidation of the geothermal structure in the Haneyama area, Oita Prefecture, the paper carried out the drilling of structural boring exploration wells, N6-HN-1 (1,605m) and N6-HN-2 (1,402m), and the well exploration. In the well exploration, the following were conducted: measurement of earth temperature, temperature recovery test, electrical log, simple water injection test, core/cutting observation, core test, powder X-ray diffraction analysis, physical property test, measurement of homogenization temperature of fluid inclusion, etc. In the temperature log and temperature recovery test, the terminal temperature at a 1,600m depth of N6-HN-1 well and at a 1,400m depth of N6-HN-2 well was 139.6 degrees C and 26.2 degrees C, respectively. The homogenization temperature of fluid inclusion was relatively higher, +70 degrees C to +100 degrees C, than that in the results of the temperature log, but was on the side of lower temperature, -30 degrees C to -100 degrees C, in a comparison with the saturated boiling curve of the earth surface and ground water level. Namely, it was thought that around the N6-HN-1 well, there used to exist the high temperature fluid of 250 degrees C or higher at the peak period of geothermal activities, but there only existed the geothermal water of approximately 140 degrees C at the present time. (NEDO)

  16. Characteristic analysis on the deformation behaviour of shell-like lattice structures subjected to follower forces; Judo kaju wo ukeru kosa arch kozo no daihenkei kyodo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Fukuchi, N.; Okada, K. [Kyushu University, Fukuoka (Japan); Fujii, M. [Namura Shipbuilding Co. Ltd., Osaka (Japan); Shiraki, M. [Toyota Motor Corp., Aichi (Japan)

    1998-09-04

    The deformation mechanisms of submerged shell-like lattice structures with membrane are in principle of a non-conservative nature since the follower type hydrostatic pressure. In the region of large deformations, especially in the case of geometrically deep shell-like lattice structures, the system could be much more accurately defined in a mono-clinically convected coordinate description than the conventional spatial description. Also, a complete analysis of a non-conservative system requires a criterion since the system can have multiple ranges of stability and instability involving buckling and snapping. This paper presents the development of the governing equations for the finite deformations of shell-like lattices defined in a mono-clincally convected coordinate description and applies the same to different cases of lattice deformations. The validity of the formulations is verified for finite deformation. The examples of some geometrically special shell-like lattice structures are presented as well to show the feasibility of the present formulation. 5 refs., 11 figs.

  17. X-ray diffraction study on microstructure of Li20-TeO2 glasses; Xsen kaisetsuho ni yoru Li{sub 2}O-TeO{sub 2} kei garasu no mikuro kozo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Iwadate, Y; Hattori, T; Nishiyama, S; Fukushima, K; Sugawara, Y [Chiba Univ. (Japan); Noda, K. [Japan Atomic Energy Research Inst., Tokyo (Japan)] Tatsumisuna, M. [Osaka Prefectural Univ., Sakai (Japan)] Umesaki, M. [Osaka Industrial Research Inst., Osaka (Japan)

    1998-07-10

    Li2O-TeO2 glasses attract attention because of unique properties such as high density, high refractive index, large dielectric constants and high infrared transmittance. The short range structures of two samples of Li2O-TeO2 glasses (15:85 mol% Li2O-TeO2 and 25:75 mol% Li2O-TeO2) were investigated by X-ray diffraction technique. Interpretation of the obtained radial distribution functions was performed on the basis of the strength comparison method. The following conclusions were obtained: Two types of Te-O bond lengths of 0.18nm and 0.20nm are found in TeO4 tetragonal bipyramid. As network forming units, the TeO4 tetragonal bipyramids and TeO3 trigonal bipyramids are observed. The TeO4 tetragonal bipyramid units are transformed into the TeO3 trigonal bipyramids through the transient species of polyhedral with non-bridging oxygen atoms with increasing content of Li2O. The lone pair of Te atom does not contribute to the formation of the glass network. 17 refs., 6 figs., 2 tabs.

  18. Structural response analysis of very large floating structures in waves using one-dimensional finite element model; Ichijigen yugen yoso model ni yoru choogata futai no harochu kozo oto kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Fujikubo, M.; Yao, T.; Oida, H. [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

    1996-12-31

    Formulation was made on a one-dimensional beam finite element which is effective in analyzing structural response of very large floating structures by modeling them on beams on an elastic foundation. This element allows strict solution of vibration response in the beams on the elastic foundation to be calculated efficiently for a case where mass and rigidity change in the longitudinal direction. This analysis method was used to analyze structural response of a large pontoon-type floating structure to investigate mass in the end part for the structural response and the effect of decay while passing the structure. With a pontoon-type floating structure, reduction in bends and bending stress in the end part of the floating structure is important in designing the structure. Reducing the mass in the end part is effective as a means to avoid resonance in these responses and reduce the responses. Increase in rigidity of a floating structure shifts the peak in quasi-static response to lower frequency side, and reduces response in resonance, hence it is advantageous for improving the response. Since incident waves decay while passing through the floating structure, response in the lower wave side decreases. The peak frequency in the quasi-static response also decreases at the end part of the structure in the upper wave side due to decay in wave force. 7 refs., 11 figs., 1 tab.

  19. Proceedings of the Spring Meeting of the Society of Naval Architects of Japan (1996). Part 2. Structure, materials, welding, construction, and design; Nihon zosen gakkai (1996 nen) shunki koen ronbun maezuri. 2. Kozo, zairyo, yosetsu, kosaku, sekkei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    This is a proceedings of the Spring Meeting of the Society of Naval Architects of Japan made public on May 15 and 16, 1996. In the basic research, the following are included: Basic studies on computer aided concurrent engineering for hull structure design and piping design; Fundamental study on the new method to estimate vibration level on a ship; Flat plate approximation in the three-dimensional slamming; Development of new finite element by source method, etc. As to fracture and cracks, Equivalent CTOD concept based on the local approach and its application to fracture performance evaluation of welded joints; Fracture mechanical modeling of brittle crack propagation and arrest of steel; An evaluation method for ductile crack propagation in pre-strained plates; Multiple fatigue cracks propagating in a stiffened panel, etc. Relating to fatigue strength, Fatigue life estimation of welded joints of an aluminum alloy under superimposed random load waves; Study on unified fatigue strength assessment method for welded structure, etc.

  20. Synthesis and structure of porous alumina precursors derived from n-alkylamine-AlCl3 system; Chokusa alkylamine-AlCl{sub 3} kei wo mochiiru takoshitsu alumina zenkutai no gosei to kozo

    Energy Technology Data Exchange (ETDEWEB)

    Yoshimura, M.; Machida, M.; Kijima, T. [Miyazaki Univ. (Japan)

    1998-06-01

    Alumina precursors have been prepared from AlCl3 by using n-alkylamines (C{sub n}H{sub 2n+1}NH2) as precipitant at pH 9.6 and pH 6.2, and the structure, composition, microstructure, and thermal decomposition behavior are investigated. The effects of the structure of the precursor on the decomposition behavior and on the surface area of porous alumina are also investigated. When alkylamines n{>=}6 are used, long periodicity phases are produced corresponding to larger than d=2.0nm spacing which can not be attributed to bayerite or pseudo-boehnite. Long periodicity phase is formed uniquely near the water content of about 50mass% (H2O/Al=4.5), and the spacing varies depending on the alkyl chainlength of amine. When the precipitate prepared at pH 6.2 is heated, water is desorbed at near 100degC, pseudo-baehnite phase is pyrolyzed at 300degC, and the precipitate changed into {gamma}-alumina at temperatures higher than 500degC. 16 refs., 9 figs.

  1. Proceedings of the Spring Meeting of the Society of Naval Architects of Japan (1996). Part 2. Structure, materials, welding, construction, and design; Nihon zosen gakkai (1996 nen) shunki koen ronbun maezuri. 2. Kozo, zairyo, yosetsu, kosaku, sekkei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    This is a proceedings of the Spring Meeting of the Society of Naval Architects of Japan made public on May 15 and 16, 1996. In the basic research, the following are included: Basic studies on computer aided concurrent engineering for hull structure design and piping design; Fundamental study on the new method to estimate vibration level on a ship; Flat plate approximation in the three-dimensional slamming; Development of new finite element by source method, etc. As to fracture and cracks, Equivalent CTOD concept based on the local approach and its application to fracture performance evaluation of welded joints; Fracture mechanical modeling of brittle crack propagation and arrest of steel; An evaluation method for ductile crack propagation in pre-strained plates; Multiple fatigue cracks propagating in a stiffened panel, etc. Relating to fatigue strength, Fatigue life estimation of welded joints of an aluminum alloy under superimposed random load waves; Study on unified fatigue strength assessment method for welded structure, etc.

  2. Structural response analysis of very large floating structures in waves using one-dimensional finite element model; Ichijigen yugen yoso model ni yoru choogata futai no harochu kozo oto kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Fujikubo, M; Yao, T; Oida, H [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

    1997-12-31

    Formulation was made on a one-dimensional beam finite element which is effective in analyzing structural response of very large floating structures by modeling them on beams on an elastic foundation. This element allows strict solution of vibration response in the beams on the elastic foundation to be calculated efficiently for a case where mass and rigidity change in the longitudinal direction. This analysis method was used to analyze structural response of a large pontoon-type floating structure to investigate mass in the end part for the structural response and the effect of decay while passing the structure. With a pontoon-type floating structure, reduction in bends and bending stress in the end part of the floating structure is important in designing the structure. Reducing the mass in the end part is effective as a means to avoid resonance in these responses and reduce the responses. Increase in rigidity of a floating structure shifts the peak in quasi-static response to lower frequency side, and reduces response in resonance, hence it is advantageous for improving the response. Since incident waves decay while passing through the floating structure, response in the lower wave side decreases. The peak frequency in the quasi-static response also decreases at the end part of the structure in the upper wave side due to decay in wave force. 7 refs., 11 figs., 1 tab.

  3. FY 1998 annual report on the project of basic survey for improving energy consumption efficiency in developing countries and programs of international conferences including IPCC. Report on CDM workshop; Hatten tojokoku energy shohi koritsuka kiso chosa nado jigyo / IPCC nado kokusai kaigi jigyo (CDM workshop hokokusho) 1998 nendo jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    It is decided in the COP4 that the concrete schemes for the (Kyoto Mechanism) should be boiled down towards the end of 2000. Of the many outstanding issues concerned, those related to the clean development mechanism (CDM) involve a number of problems awaiting solution. In particular, setting the baselines for amounts of the greenhouse effect gas emissions in projects not existing, which are essential for identifying reduced amounts of emissions (or credits), poses serious difficulty because of wide arbitrariness involved in the methodology. Therefore, (standardization) of the procedures is demanded for the accurate identification. In actuality, however, no methodology has been established as to what methods will be possibly applicable to widely diversified types of projects. This workshop, therefore, has focused the discussions on the (baseline problems), expecting to serve as a trigger for the future directions by presenting international researches and promoting the discussions thereon to deepen recognition of these problems, where the AIJ experiences have served as one of the bases. (NEDO)

  4. Report on achievement in the preceding research related to global industry technologies for the global industry technology research and development project. Research on gas systems substituting global warming gases such as PFC used in manufacturing semiconductors; 1998 nendo chikyu kankyo sangyo gijutsu ni kakawaru sendo kenkyu. Handotai seizo nado ni shiyosuru PFC nado no chikyu ondanka gas no daitai gas system no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The present semiconductor manufacturing process uses a great amount of PFC having large global warming coefficients and extremely long atmospheric life. A research was made particularly on reduction of its emission from etching processes. After introducing how the semiconductor industry has been working conventionally on protection of the global environment, this paper makes clear the purpose and positioning of this preceding research, as well as how it is moved forward. The paper also reports the results of analyzing and discussing the exhaust gases from etching devices using several kinds of substitute PFC gases. Survey results are reported on the possibilities of new substitute gases, plasma decomposition and treatment of exhaust gases, reaction process simulation, and in-situ analyzing and evaluating technologies. Investigations were made on the possibility of using no PFC in wiring processes which consume greater amount of PFC, as well as on wiring techniques using inter-layer insulation film with low dielectric rate, a new wiring structure forming technology, new functional elements, circuits and systems in a wide range. Proposals were given on specific research and development themes and plans that begin in fiscal 1999. (NEDO)

  5. FY 1999 report on the study of the future course, etc. of 'the basic survey for promotion of Joint Implementation, etc.'; 1999 nendo 'kyodo jisshi nado suishin kiso chosa' no kongo no hokosei nado ni kansuru kento chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The paper conducted the demonstration of the multiplier effect of 'the model project for heightening of the international energy consumption efficiency, etc.' carried out by NEDO and its subsidiary project, 'the project on the basic survey for promotion of Joint Implementation (JI),' and the comparative study between these projects and the JI/CDM projects proposed in the world. In the quantitative evaluation of the multiplier effect, in the case of making the demonstration of the same technology in the same area both in the model project and the basic survey for promotion of JI, it becomes possible to grasp the CO2 reduction effect with high accuracy, but the CO2 reducible amount is small. Inversely, as to the technology for which the basic survey for promotion of JI is studied, but the model project is not carried out, it becomes possible to grasp the CO2 reduction effect with low accuracy, the CO2 reducible amount is large. In the comparison with the JI/CDM projects proposed in the world, the CO2 reduction amount was approximately $2.7 billion, 250 million tons, in the UNFCCC project, and approximately $5.0 billion, 500 million tons, in the IJ project. There was no very big difference in the cost effect. (NEDO)

  6. FY 2000 International energy use rationalization project. International technology dissemination project for improving energy consumption efficiency (Green helmet project for steel heating furnaces in Thailand); 2000 nendo kokusai energy shiyo gorika nado taisaku jigyo chosa hokokusho. Kokusai energy shohi koritsuka nado gijutsu fukyu jigyo (Green helmet jigyo (Tai: kozai kanetsuro))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The project for energy saving dissemination activities and technological assistance for Thailand is carried out, and the FY 2000 results are reported. For Siam Iron and Steel (SISCO), the experts are dispatched for reviewing the operating conditions of the facilities constructed by the model project, their maintenance and examination, time series diagnosis of the recuperator performance, and providing technical assistance for fuel consumption and high-load combustion of the downstream unit. Furthermore, the site survey and technical assistance are provided for two newly selected Thai steel enterprises, Sahaviriya Steel Industries Public Co. (SSI) and the Bangkok Iron and Steel Works Co. (BISW). For SSI, it is predicted that energy of approximately 50Mcal/ton can be saved by, e.g., enhancement of waste heat recovery, enhancement of heat insulation of skid pipes, introduction of steel discharging temperature prediction system, and combustion control. For BISW, it is predicted that energy of approximately 25Mcal/ton can be saved by, e.g., enhancement of waste heat recovery and reduction of heat loss in the waste gas. (NEDO)

  7. Fiscal 2000 survey report on rationalization project for international energy conservation, technological dissemination project for international energy conservation, and Green Helmet Project. Japan-China alternative energy seminar/waste disposal; 2000 nendo kokusai energy shiyo gorika nado taisaku jigyo, kokusai energy shohi koritsuka nado gijutsu fukyu jigyo, green helmet jigyo chosa hokokusho. Nicchu sekiyu daitai energy seminar haikibutsu shori

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper explains the Japan-China alternative energy seminar (February 28 and March 1, 2001, at Beijing). The purpose of the seminar is to introduce systematic and three-dimensional or land/sea/air measures for waste disposal including recycling in Japan, to provide guidance of measures in improving recognition and methods for waste disposal in China, and also to contribute to the dissemination and promotion of a model project for effectively utilizing waste heat from rubbish incineration, a project being implemented in Harbin City now. The activities of NEDO were introduced, with emphasis placed on a model program, called Green Aid Project, for managing heat from waste incineration. On the subjects of sustainable development, urban environment, and energy, the policy of China's tenth five-year plan was demonstrated, and the treatment of wastes in China was also explained. The present state of waste processing in Japan was introduced, as was its maintenance of the facilities. Concerning Japan's waste processing technologies and characteristics of the equipment, there were presented non-incineration processing including crushing/separating, RDF, compost, methane fermentation, etc.; incineration plants; and each of the technologies such as combustion, exhaust gas, ash treatment, use of remaining heat, and gasification melting. (NEDO)

  8. Fiscal 2000 report on cooperative basic project on international energy consumption improvement/International conference project such as IPCC. International Symposium on the Kyoto Mechanisms; 2000 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo / IPCC nado kokusai kaigi jigyo Kyoto mechanism ni kansuru symposium hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-06-01

    The above-named symposium was held at United Nations University in the period April 12-13, 2001, and the conference is outlined in this report. The symposium aimed to contribute to the progress of international rule making and to the enhancement of mutual understanding through the exchange of views and opinions by negotiators representing their countries over the Kyoto mechanisms, the rule of emissions trading in particular, and through the analysis of negotiators' options; to discuss how international rules should be from a practical viewpoint with the participation of people related to the market or industries and engaged actively in the implementation of the mechanisms; to enrich Japanese people's knowledge about the mechanisms and to enhance their understanding of greenhouse gas emissions reduction techniques making use of the mechanism of the market; and so forth. The conference included Session 1: Current status of international negotiations and views from parties, Session 2: Toward credible and workable scheme of the mechanisms (Parts 1 and 2), and Session 3: Emissions trading - Outstanding issues and options. (NEDO)

  9. FY 1999 survey report on the survey of destruction technology of HFC, etc. for rationalization of energy use. Survey of the actual state of use/recovery/emissions of HFC, etc.; 1999 nendo energy shiyo gorika HFC nado hakai shori gijutsu chosa hokokusho. HFC nado shiyo kaishu haishutsu jittai chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This survey was aimed at collecting the basic data for studying a possibility of conversion of the recovery system of refrigerant freons, mostly DFC, into HFC, etc., which has been proceeded with in Japan. Of HFCs, PFCs and SF{sub 6} used for survey, only SF{sub 6} is now being recovered and processed. As to HFCs, HFC-134a was arranged, and the recovery/destruction to meet users' handling methods are requested because of the diverse usage and users. The points of the control of emissions of chemical substances into the atmosphere are the decrease in number of times of transport/filling-up at the time of materials handling and the closed system in plants and installation. If considering the heightening of efficiency of materials flow, requested are the decrease in number of times of transport/filling-up, the increase in quantity received by users, and measures to be taken for leakage at the time of receiving. In relation to the conversion of the recovery system of refrigerant freons, mainly CFC, into HFC, etc., all the industries concerned with the generation of the used substances to the materials flow have to promote the technical development for the structure and recovery in cooperation with each other. (NEDO)

  10. Research and development of utilization technology of solar thermal system for industrial and other use. Development of passive solar system (research and development of advanced glazing); Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Passive solar system no kaihatsu (chokozai nado no kenkyu kaihatsu (advanced grazing no kenkyu kaihatsu))

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for advanced glazing in which solar energy is efficiently utilized. The peripheral techniques are surveyed for evaluation of characteristics of large-size dimming glass, optimization of film compositions and scaling up. The dimming device, made on a trial basis, attains a target controllable rage of at least 50% for visible light transmittance. The suitable components include WO3 as the electrochromic material producing color under a reducing atmosphere, NiO as the counter electrode producing color under an oxidative atmosphere, and hydrated SbOx as the proton-conducting electrolyte. The test results indicate possibility of the dimming glass stably operable while being irradiated with a quantity of sun ray of around 10 years. The study on scaling up the dimmer glass develops, on a trial basis, a process for producing large-size glass and evaluates its characteristics, where the film parameters are investigated. It also investigates the peripheral techniques for assembling the devices for the large-size glass, and develops useful techniques, such as those for sealants and improved sealing methods. 1 fig., 1 tab.

  11. Fiscal 2000 report on cooperative basic project on international energy consumption improvement/International conference project such as IPCC. International Symposium on the Kyoto Mechanisms; 2000 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo / IPCC nado kokusai kaigi jigyo Kyoto mechanism ni kansuru symposium hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-06-01

    The above-named symposium was held at United Nations University in the period April 12-13, 2001, and the conference is outlined in this report. The symposium aimed to contribute to the progress of international rule making and to the enhancement of mutual understanding through the exchange of views and opinions by negotiators representing their countries over the Kyoto mechanisms, the rule of emissions trading in particular, and through the analysis of negotiators' options; to discuss how international rules should be from a practical viewpoint with the participation of people related to the market or industries and engaged actively in the implementation of the mechanisms; to enrich Japanese people's knowledge about the mechanisms and to enhance their understanding of greenhouse gas emissions reduction techniques making use of the mechanism of the market; and so forth. The conference included Session 1: Current status of international negotiations and views from parties, Session 2: Toward credible and workable scheme of the mechanisms (Parts 1 and 2), and Session 3: Emissions trading - Outstanding issues and options. (NEDO)

  12. Fiscal 1999 technical survey report. Basic project on international cooperation on energy consumption improvement, etc. (Japan International Cooperation Center project on promotion of exchange of specialists); 1999 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo / kokusai energy shohi koritsuka chosa nado kyoryoku kiso jigyo chosa hokokusho. Kokusai kyoryoku center jigyo suishin senmonka koryu sokushin jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    Specialist related to the governments of Thailand, Malaysia, and Indonesia where NEDO (New Energy and Industrial Technology Development Organization) implements its model projects were invited. They exchanged opinions with officials of the Japanese Government and affiliated organizations over measures for effective energy utilization. Opinions were also exchanged over the response of energy-consuming industries, development of technologies, and the status of their adoption. Activities of government-related participants are described below. Under a Model Project for Utilization of Waste Heat from Incineration of Industrial Waste at Industrial Estate, five Thai people with Industrial Estate of Thailand visited Ministry of International Trade and Industry, NEDO, NKK Corporation, Toyota Motor Corporation, and Keiyo Food Industrial Park. Under a model project on the recovery of waste heat from paper sludge incineration, four Malaysian people with Ministry of Energy, Communications and Multimedia or with Energy Center visited Ministry of International Trade and Industry, NEDO, NKK Corporation, Toyota Motor Corporation, and Japan Paperboard Industries Co., Ltd. Under a model project on the utilization of paper sludge and solid waste, four Indonesian people with Ministry of Industry and Trade or with Ministry of Mines and Energy visited Ministry of International Trade and Industry, NEDO, Babcock-Hitachi K.K., and Oji Paper Co., Ltd. (NEDO)

  13. Report for fiscal 1999 on the international and fundamental cooperation project for energy consumption efficiency improvement and the international conference project such as IPCC. The meetings of IPCC specialists and IPCC symposiums; 1999 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo / IPCC nado kokusai kaigi jigyo. IPCC senmonka kaigo oyobi IPCC symposium hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-10-01

    This paper reports the meetings of specialists and the symposiums by the inter-governmental panels for climate change (IPCC) in fiscal 1999. Three working groups were established for evaluation on climate change from scientific aspects, evaluation on effects and countermeasures from socio-economic aspects, and evaluation on mitigation measures from socio-economic aspects. The working groups have started preparing the third evaluation reports. Common problems are handled in a unified framework as the traversable problems. Specialist meetings are held for several important themes. Especially for the cost problems, preparation of a guidance paper has started, that include the costs and benefits by territories and departments. The themes for the specialist meetings include: cost problems related to effects and countermeasures for climate change and mitigation measures; the IPCC activities for the cost evaluation in the past and an outline of the traversable problems; problems in effects, applicable measures, and mitigation measures; and unification of the cost evaluations. The themes for the symposiums are the frontier line of the climate change problems, and include the outline of IPCC, the current status and issues in the working groups and the special reports for each group. (NEDO)

  14. FY 2000 report on the basic survey to promote Joint Implementation, etc. Prevention of emissions of gasoline vapor from oil depots in Indonesia; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Indonesia sekiyu kichi nado kara no gasoline joki hoshutsu no boshi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A field survey was conducted of oil shipment depots in Java and Bali islands owned by Indonesia's state-run oil company to study measures for reduction in greenhouse effect gas emissions. Studies were made on the grasp of the amount of the hydrocarbon vapor emitted into the air, the amount of the gasoline recovered in case of adopting the vapor emission preventive technology, equipment cost/operational cost, etc. Concretely, the following three were studied: change of the gasoline storage tank to the inner floating roof type, and prevention of evaporation loss at the time of receiving and breathing loss caused by temperature changes; replacement with the vapor recovery type loading arm to recover gasoline vapor generated at the time of shipment/filling, and installation of the vapor recovery unit to recover vapor as gasoline; vapor balance system to recover in underground tank the gasoline vapor generated at the time of filling gasoline at gas station. As a result of the study, the recovered gasoline amount was 66,393 Kl/y and the CO2 reduction amount was 14,474 t/y at oil shipment depots and approximately 650 gasoline stations in Jakarta and Surabaya. (NEDO)

  15. FY 1999 report on the results of the investigation of feasibility of joint implementation promotion through plant-related technology transfer to Central/Eastern European countries; 1999 nendo Chu Too nado chiiki ni okeru plant yushutsugata gijutsu iten wo tsujita kyodo jisshi nado suishin kanosei ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Feasibility of joint implementation promotion through plant-related technology transfer is investigated for 15 Central and Eastern European countries. Emissions of the greenhouse effect gases can be relatively easily abated in these countries by improving energy utilization efficiency, because they have more advanced infrastructures than developing countries, and are behind the developed countries in modernization of the facilities. Therefore, European and North American countries have been positively promoting the AIJ programs in these countries, and there are fierce competitions for promising projects. It will be necessary for Japan to provide public loans, e.g., environmental yen loans, to promote the plant-related JI/CDM projects in these countries. Many of these countries have not drawn plans for reducing emissions of the greenhouse effect gases, and expect establishment of the international cooperation systems for exchanging information related to global warming problems, and introducing the Japanese technologies and policies. (NEDO)

  16. Report on the achievements in the Sunshine Project in fiscal 1987. Collection of data from coal liquefaction processes, and development of a disposal system; 1987 nendo sekitan ekika process nado no data no shushu, shori system nado no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The present study is intended to investigate the current status of the information control system in the coal liquefaction technology development project, and structure a coal liquefaction database system to manage and utilize comprehensively the items of information provided by the system. Section 2 shows the result of epitomizing opinions on the purpose of the coal liquefaction database by means of a questionnaire survey to NEDO, and opinions of people of experience and academic standing. Section 3 depicts the basic conception of a coal database total system. Section 4 summarizes the conceptual idea of the fundamental database by washing out the data input and output, and the contents recorded in the database. Section 5 summarizes the basic sub-system required for management and utilization of the database, and different application systems for data analysis required in each stage of performing the coal liquefaction technology development, and for operation assistance. Section 6 summarizes a general technological information retrieval system, in which general information on coal liquefaction is recorded, processed, and registered and accumulated in the database, and then the information retrieval and the original information providing service are carried out. Section 7 summarizes philosophies on development and operation of the coal liquefaction database, operating institutions, and problems to be solved. (NEDO)

  17. Project for rationalization measures for international energy conservation. Model project concerning efficient consumption of energy for international energy conservation (Model project of waste heat recovery on billet reheating furnace); 1999 nendo kokusai energy shiyo gorika nado taisaku jigyo seika hokokusho. Kokusai energy shohi koritsuka nado model jigyo (kozai kanetsuro hainetsu kaishu model jigyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of curtailing energy consumption in the steel industry, a heavy energy consuming industry in Thailand, a model project was carried out for waste heat recovery on a billet reheating furnace, with the fiscal 1999 results compiled. This model project is to install a high efficiency recuperator and the latest combustion control system in the existing furnace in a SISCO (The Siam Iron and Steel Co., Ltd.) plant in Thailand. This year, following the preceding year, the construction manual was prepared, as were the test run manual, performance verification manual, operation and maintenance manual, etc. Supervisors were also dispatched to the site, giving guidance of the installation work, test run and the demonstrative operation, on the basis of these documents. Operation for verifying performance of the equipment was implemented on November 17, 1999, with the intended results obtained. Subsequently, operation maintenance instructors were dispatched, with energy saving effect proved through the collection/analysis of operation data and monitoring, for example. Further, as the dissemination activities, pamphlets and videos were prepared, and seminars were held, among others. (NEDO)

  18. Report on the fiscal 1993 investigational study of the environmental technology development trend in Japan. Trend survey of the introduction policy of environmentally friendly products; 1993 nendo Nippon ni okeru kankyo gijutsu kaihatsu doko nado ni kansuru chosa kenkyu hokokusho. Kankyo chowagata seihin no donyu hosaku nado doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-05-01

    An investigation was conducted into the systematical scheme for the introduction and promotion of environmentally friendly products mostly to the U.S., Europe and China. In the U.S., the introduction policy is given to one and all fields of the industry. The introduction policy of the U.S. has a characteristic that the introduction is left to the market principle by DSM or permit dealing, etc. except the preferential tax system and systematical finance in which the government is concerned. The policy of European countries is characterized by the idea preceding, standards or rules are first given, and the whole is pushed on to them. Accordingly, it seems that there is few atmosphere of expecting to receive the government side economic incentives from the corporate side. Legal regulations on the environment in China were prepared in a comparatively early time (1979), but the supervision of obeying the regulations and the appearance/spread of environmentally friendly product menus have just started. Accordingly, as the introduction policy on environmentally friendly products, there was found nothing valuable but the regulations. 12 refs., 3 figs., 15 tabs.

  19. Report on achievement in researching aids for practical application of recycling technologies in fiscal 1998. Development of a technology to treat hard-to-decompose chemical substances in incineration ash; 1998 nendo recycle gijutsu nado jitsuyoka shien kenkyu seika hokokusho. Shokyakubaichu no nanbunkaisei kagaku busshitsu nado no shori gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    This paper describes development of a technology to decompose dioxins in incineration fly ash. Experiments were carried out during fiscal 1998 by using a bench-scale plant and a laboratory-scale plant of the installed supercritical water treatment equipment designed and fabricated in fiscal 1997. With the bench-scale plant, operation methods were discussed, whereas high temperature and pressure operation of 25 MPa and a temperature internal to the reactor of 350 degrees C were achieved. An alcohol combustion test and a preliminary slurry delivery test were also performed. With the laboratory-scale plant, operating methods were discussed, and combustion tests were carried out by using different organic matters as fuels for the supercritical water oxidation reactor. Investigations were executed on the effects of reactive operation parameters on organic matter decomposition rates, produced gas compositions, and reactor wall temperatures. The intensity of hydrogen bond between solvent and water has decreased to almost half of the normal temperature and pressure water in the vicinity of the critical point. However, strong interaction still remained in terms of per unit density. A portable equipment (650 degrees C and 25 MPa at the maximum, and standard treatment quantity of dry fly ash of 1 kg/h) was operated for demonstration. Operation methods and organic matter decomposition characteristics were identified in alcohol operation and slurry operation. (NEDO)

  20. Report on the achievements in the Sunshine Project in fiscal 1988. Development of a collection and processing system for data of the coal liquefaction process; 1988 nendo sekitan ekika process nado no data no shushu, shori system nado no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-03-01

    Storing and managing comprehensively a huge amount of data acquired in developing the coal liquefaction technologies would greatly contribute to moving forward the development of the coal liquefaction technologies, and realizing a commercial plant being the ultimate goal. It is intended to investigate the current status of information management systems used for development projects being implemented or planned in developing the coal liquefaction technologies. It is also intended to structure a coal liquefaction database system to utilize comprehensively and effective the information discovered by the above investigation. The current fiscal year has performed developments on the following items to structure a coal liquefaction database system by using a computer: (1) conceptual design of the fundamental database, and (2) basic design on a general technological information retrieval system. The development during the current fiscal year established a method to classify levels of data accommodation for the fundamental database based on the investigation and analysis of the experimental data. In addition, with regard to the general technological information retrieval system, summarization was performed on the specifications of the hardware and software, the basic configuration, the input and output specifications, and the retrieval screens. (NEDO)

  1. FY 1999 report on the results of the research and development project for new industry creation type industrial science technologies. R and D of the intellectual material and structural systems (R and D of the intellectual material and structural systems); 1999 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki zairyo kozo system no kenkyu kaihatsu (chiteki zairyo kozo system no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 1999 results of the R and D project for development of intellectual materials and structural systems, where the fibrous or leafy sensor material or element (muscle) is integrated with a structure of an advanced material (skeleton) to process and control information (brain). The program for development of the health monitoring technologies develops the fine optical fiber (diameter: 40{mu}m), which is on a level with the conventional 125{mu}m-diameter fiber in strength and fatigue characteristics, for the high-performance sensor systems. The self-diagnosis of soundness, e.g., detection of impact loads and damages, is attempted using the fine optical fibers embedded in the composite structures. The program for active-adaptive control of smart structures investigates control of vibration and noise for beam structure elements, using the theoretical model developed for shape memory alloys. The vibration tests are conducted, where a distribution type sensor is used for active-adaptive control of soft structures, and the good results are produced. The program for development of actuator materials and elements produces high-strength, high-toughness PZT and PNN-PZT sheets of uniformly distributed thickness by the doctor blade method. (NEDO).

  2. FY 1993 research and development of the technology for controlling structures of functional composite members. R and D of advanced surface processing for methane-fueled aircraft engine members (Technology for controlling the microscopic structures of superhigh-temperature members); 1993 nendo fukugo kino buzai kozo seigyo gijutsu no kenkyu kaihatsu (methane nenryo kokukiyo engine buzai no kodo hyomen kako gijutsu kaihatsu). Chokoon buzai micro kozo seigyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Described herein are the results of the FY1993 research and development project, implemented for development of the technologies for modification of material surfaces and interfaces, with the objectives to develop the optimum members for methane-fueled aircraft engines. For R and D of multi-layered films with controlled microscopic structures, the tests are conducted for forming thin-film layers by, e.g., ion implantation, ion mixing and implantation of large quantities of ions as the surface controlling/modification techniques based on, e.g., ionic techniques. The tests are conducted for, e.g., chemical vapor-phase reaction evaporation and low-pressure plasma spraying as the technologies for forming multi-functional films of, e.g., high reliability and resistance to corrosion. For development of the technologies for controlling/compositing the microscopic structures, the tests are conducted for, e.g., selection of the matrix materials, and prevention/removal of defects by the chemical vapor-phase reaction penetration treatment effected for extended periods. For development of the technologies for evaluation of the characteristics under superhigh-temperature environments, the tests are conducted to investigate the mechanical characteristics of isotropically uniform metallic materials under multi-dimensional stresses and evaluation thereof, and mechanical and thermal characteristics of carbon-fiber-reinforced carbon composites and evaluation thereof. (NEDO)

  3. ¿Alcoholismo en Galicia: un camiño sen esperanza?

    OpenAIRE

    Folgar de la Calle, José María; Martín Sánchez, Rita

    2012-01-01

    O alcoholismo en Galicia é un mal endémico, polo que os enfermos non son considerados marxi­ nados. Os dous filmes que comentamos tentan chamar a atención e concienciar á sociedade sobre o carácter atípico deste problema.

  4. "It's not the size of the ship…"

    DEFF Research Database (Denmark)

    Christiansen, Ask Vest; Gleaves, John

    2013-01-01

    the challenge and reflected upon the conference theme "What do we (really) know about doping?" in their presentations. Not only as regards to the reliability of official statistics and the information that flows from organisations, NADOs and other stakeholders in sport, but also the more demanding task...

  5. Simulation of the Tornado Event of 22 March, 2013 over ...

    Indian Academy of Sciences (India)

    2013-03-22

    Mar 22, 2013 ... nagar and Akhaura upazila of Brahmanbaria district (DMIC 2013). Other damages of this tor- nado event were the damages and/or collapses of electric lines and poles, boundary wall, entrance gate, communication systems, breaking down of numerous trees, etc. The location of Brahmanbaria. (23.95.

  6. School Principals and Racism: Responding to Aveling

    Science.gov (United States)

    Charles, Claire; Mahoney, Caroline; Fox, Brandi; Halse, Christine

    2016-01-01

    This study responds to Nado Aveling's call in "Anti-racism in Schools: A question of leadership?" ("Discourse: Studies in the Cultural Politics of Education," 2007, 28(1), 69-85) for further investigation into racism in Australian schools. Aveling's interview study concluded that an overwhelming number of school principals…

  7. Element analysis of Japanese traditional papers by PIXE method

    International Nuclear Information System (INIS)

    Suzuki, Tatsuya; Yasuda, Keisuke; Tani, Teruhiro

    2000-01-01

    The Japanese papers, 'washi', are made from the bast fibers of the plants. Since washi have the informations of the raw material plants, there is potentiality of the identification of the production place by the element analysis of the washi. Three kinds of washi made of kozo, which have different habitats, were prepared. The elements in their washi were measured by the PIXE. It was confirmed that the amount of elements included in the washi depend on the habitats of their raw material plants. (author)

  8. Confirmation study of the effectiveness of prospect techniques for deep geothermal resources. Deep-seated geothermal resources survey report (Fiscal year 1993); 1993 nendo chinetsu tansa gijutsu nado kensho chosa. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Drilling and survey of deep geothermal exploration wells were conducted in order to grasp the existing situation of deep geothermal resource and the whole image of geothermal systems in the area where geothermal resource was already developed. Following fiscal 1992, the well was drilled in fiscal 1993 down to depths of 605m-1505m, and a 13-3/8 inch casing was inserted down to a depth of 1500m. In the drilling, four cores including oriented cores were sampled, and microscopic observation, X-ray diffraction analysis, fluid inclusion survey, core property test, etc. were conducted. In the FMI logging, detected were 273 bedding planes, 483 fractures, etc. Further made were a velocity structure survey, a gravity survey in the area of 270 km{sup 2} including deep exploration wells, a quality survey of the Kakkonda river water, etc. As to geothermal structure models in the Kakkonda area, results of the drilling were added to prediction models before drilling deep exploration wells, but the revision was not very much. Besides, studies were made of a survey method using microearthquakes, a survey technique using resistivity, etc. 61 refs., 259 figs., 95 tabs.

  9. FY 1998 report on the verification survey of geothermal exploration technology, etc. 1/2. Survey of deep geothermal resource; 1998 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 1/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-12-01

    For the purpose of commercializing deep geothermal resource, a deep exploration well of 4000m class was drilled in the existing geothermal development area to survey the situation of deep geothermal resource existence and the availability. Concretely, the deep geothermal exploration well was drilled for study in the Kakkonda area, Shizukuishi town, Iwate prefecture, to clarify the situation of deep geothermal resource existence and the whole image of geothermal system. Consideration was made of the deep geothermal exploration method, systematization of deep high temperature drilling technology, and availability of deep geothermal resource. The results of the survey were summed up as follows: 1) general remarks; 2) deep exploration well drilling work; 3) details of the study. 1) and 2) were included in this report, and 3) in the next report. In 1), the items were as follows: the study plan/gist of study execution, the details and results of the deep geothermal resource survey, the outline of the deep exploration well drilling work, and the outline of the results of the FY 1998 study. In 2), the drilling work plan/the actual results of the drilling work were summed up. As to the results of the study, summarized were the acquisition of survey data on deep exploration well, heightening of accuracy of the deep geothermal resource exploration method, etc. (NEDO)

  10. Fiscal 1997 report on the cooperative research on the preservation and sustainable utilization of biological diversification; Seibutsu tayosei hozen to jizokuteki riyo nado ni kansuru kenkyu kyoryoku (1997 nendo hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Cooperative researches were conducted between Japan and Thailand, Indonesia and Malaysia for the purpose of the technology development to make developing countries themselves preserve bioresources existing in tropical forests and use those sustainably. The research subjects for Thailand are a strategical study on eating of the primates, improvement of a microorganism culture collection system, preservation of biological diversification using an artificial ecosystem, bioresource utilization, etc. The subjects for Indonesia are a study of a microorganism culture collection system, study of plant preservation technology, study of microorganism utilization technology, study of plant utilization technology, promotion of the founding of the Indonesia tropical bioresource information center, etc. The subjects for Malaysia are biological diversification database and gene bank, assessment/monitoring of the ocean ecosystem, assessment and inventory of the ecosystem using hi-tech technology, search/separation of bioactive substances originated from microorganism/plant, etc. 26 refs., 24 figs., 81 tabs.

  11. Fiscal 1998 research report. Popularization project of the proper treatment technology of industrial wastes in Asian regions; 1998 nendo chosa hokokusho. Asia chiiki sangyo haikibutsu tekiseika shori gijutsu nado fukyu sokushin jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Study was made on popularization of the proper treatment technology of industrial wastes in Asian regions. In principle, industrial wastes should be recycled in a country concerned, however, because of a difference in technology and industrial location, treatment of all industrial wastes in a country concerned is impossible. International cooperation is thus indispensable to promote proper efficient practical measures for environment. For studying the possibility of the international cooperation between Japan and Asian countries concerned for further recognition and solution of industrial waste problems, 'International Symposium on the Asian Industrial Waste Issue' have been held in Tokyo since 1997 for governmental staffs. In fiscal 1998, Malaysia was invited in addition to China, Philippines and Thailand for popularization of the proper treatment and recycling of industrial wastes in Asian regions. In every Asian countries, poor collection of discharge, treatment and disposal data is an obstacle to effective treatment. Technical cooperation and financial support by developed countries are demanded. (NEDO)

  12. Report for fiscal 1998 on industrial waste optimized treatment technologies dissemination and promotion business for asian region. Holding a symposium; 1998 nendo chosa hokokusho. Asia chiiki sangyo haikibutsu tekiseika shori gijutsu nado fukyu sokushin jigyo (symposium kaisai)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    An International Symposium on the Asian Industrial Waste Issue was held in Tokyo on 4 February 1999, where lectures were delivered by participants representing China, the Philippines, Thailand, Malaysia, and Japan. More 150 people attended the event, with questions and answered animatedly exchanged between the lecturers and the audience. The progress of urbanization is quite rapid in China, with the quantity of waste increasing every years to justify the anticipation that there will be a very sharp increase in refuse incineration in the near future. Raising a serious problem in China these days is the plastic waste. In the Philippines, there are no private-sector waste treatment/disposal facilities and corporations are not obliged to take care of their waste. Consequently, very little treatment or recycling is being undertaken. In Thailand, although waste treatment/disposal centers are in operation financed by the Government and private sectors, the cost is very high, and the Government policy is that private investment will be encouraged and supported in future. In Malaysia, privatization is in progress of the business of managing waste in the solidified form. A comprehensive waste treatment/disposal plant was completed in 1998 by the endeavors of a Denmark-Malaysia consortium, and is in operation since then. (NEDO)

  13. Basic investigation on promotion of joint implementation in fiscal 2000. Survey on energy saving and CO2 emission reduction in Cilacap Refinery; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Cilacap seiyusho ni okeru shoene CO2 sakugen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective of saving energy and reducing greenhouse gas emission, a basic survey has been performed on the atmospheric crude oil distillation units and the high vacuum distillation units at Cilacap Refinery in Indonesia. The first site survey in September 2000 has carried out a survey on the situation of the facilities and operation upon obtaining the facility data and operation information from Pertamina. As a result, it was revealed that there is a room of improvement in the heat recovery, whereas a modification design was executed on the improvement proposals on the heat exchanger system. However, the second site survey in November 2000 has revealed that Pertamina had executed in 1998 through 1999 the de-bottlenecking project on the crude oil atmospheric distillation units (two units) and the high vacuum distillation units (two units), by which the capability has been expanded, and the heat recovery rate has been increased. It is not possible to look for extremely large enhancement of the heat recovery rate beyond that point, and the reduction of CO2 emission would also be small. As a result of discussions, the present project was found capable of reducing annually the CO2 emission by 36,500 tons. (NEDO)

  14. Report on fiscal 1999 survey for geothermal exploration technology verification. Survey of deep-seated geothermal resources; 1999 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    To promote the development of deep-seated geothermal resources in a rationalized way, studies were conducted about deep-seated geothermal resource assessment techniques, development guidelines, and the like. For the development of techniques for estimating deep-seated geothermal reservoir parameters, the Uenotai district, Akita Prefecture, and the Hatchobaru district, Oita Prefecture, were designated as model fields, and a geothermal system conceptual model was fabricated. Data of the two districts were registered in a database. Using these data, verification was performed of the validity of stochastic estimation techniques, large area flow simulation, rock/water equilibrium reaction simulation, and the like. As for the technique of deep-seated resource amount estimation, a simplified reservoir model was experimentally constructed based on parameters determined by the stochastic estimation of deep-seated reservoirs and on the conceptual model, and a method was studied for TOUGH2-based production prediction. Studies were also made about deep-seated geothermal resource development guidelines, such as exploration guidelines, exploration well boring guidelines, and geothermal fluid production guidelines. (NEDO)

  15. FY 1998 report on the results of R and D projects by local consortiums for immediate effects. Development of woody ceramics and application to building parts; 1998 nendo woody ceramics no sosei to kenchiku buzai nado eno oyo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D project has been implemented for developing materials for, e.g., light, highly heat-insulating and energy-saving type building parts (e.g., roofing tiles and tiles), and light tableware having warmness of wood. The stock materials for china and porcelain, roofing tile clay, tiles and cement are dispersed with hollow microcapsules as the filler, which are of glassy balloons thermally treated to be highly functional, in order to develop superlight, highly heat insulating and high-strength materials. For development of the woody ceramic materials, the microcapsules are investigated for size, thickness, thermal shrinkage, fusibility, compressive stress, reinforcing mechanisms, and monodispersibility. Also investigated are optimization of material formability, development of commercial ceramics and evaluation of their marketability, decoration techniques, antimicrobial membrane materials and their immobilization techniques, development of antimicrobial ceramic tiles, evaluation of the antimicrobial membranes, evaluation of resistance to microwaves, and so on. The efforts are also directed to researches on fundamental techniques for woody tile clay, and R and D of the application techniques and products of the woody cement. (NEDO)

  16. Report for fiscal 1994 on commissioned operation for research cooperation related to simplified purification system for industrial waste water; 1994 nendo sangyo haisui nado no kan'i joka system ni kansuru kenkyu kyoryoku hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    With an objective to serve for environmental preservation in developing countries, joint researches have been performed on anaerobic waste water treatment systems utilizing bio-technology. This paper summarizes the achievements in fiscal 1994. In the research cooperation with Thailand, a reactor applicability test was performed by using a pilot plant to determine the operating conditions, and necessary data were obtained. The pilot plant was completed of installation in November. In the research cooperation with Indonesia, Tofu manufacturing waste water was selected as the object of pilot plant research. In the detailed design the Tofu manufacturing waste water shall be treated anaerobically, and the kitchen waste water shall be treated aerobically to acquire the intended water quality. In the research cooperation with Malaysia, as a result of visiting six industries and 22 factories for investigation, waste waters from chemical and foodstuff factories were selected as the object waste waters for the research. Three researchers from Thailand and Indonesia respectively were received in Japan to provide education including experimental training and visits to waste water treatment facilities. (NEDO)

  17. FY 1999 report on the development of technology to recycle architectural waste materials, glass, etc. Development of technology to recycle architectural waste materials; 1999 nendo kenchiku haizai glass nado recycle gijutsu kaihatsu seika hokokusho. Kenchiku haizai recycle gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    Waste wood materials in the materials discharged from architectural disassembly were regarded as a potential wood resource, and the R and D of the technology to recycle these were conducted. Studies were made on the technology to finely grind waste wood materials, technology to compress/form waste wood materials and ground wood powder, verification of strength characteristics/dimension stability of the formed wood materials, etc. As to the wood materials which were badly degraded under ultra violet rays, they were coloring-processed by the steam treatment, and a possibility of coating substitution was confirmed. In relation to the technology to produce compressed wood materials, the optimization of heat treatment conditions was experimentally conducted. About the technology to give dimensional stability, dimensional stability was improved as a result of the improvement of chemicals feeding and the development of chemically processed drugs. In the development of light formed products, the board was successfully formed which is light in weight using lignocelluloses/inorganic hydrates and has the bending strength higher than that of the plaster board. In the development of interior materials, the technology was developed in which ground wood powder and thermo-plastic resin are mixed for die molding, and the OA floor using this was commercialized. (NEDO)

  18. Basic investigation on promotion of joint implementation in fiscal 2000. Efficiency improvement and energy conservation at Uong Bi power plant; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Uong Bi hatsudensho no koritsuka to sho energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Discussions have been given on energy conservation, and reduction in greenhouse gas emission through efficiency improvement at the Uong Bi coal burning power plant in Vietnam. The Uong Bi power plant, which has become using coal of lower quality than the design value, has had incomplete combustion, resulting in increase of unburned components in ash, and decrease of the boiler efficiency to 65 to 70%. Clinker hopper troubles have been occurring frequently, causing plant shutdown at a number of times. The turbine efficiency also shows as very low value as 26 to 27%. The plan has envisaged replacement of combustion parts of the boilers, withdrawal and replacement of the turbine generation systems, new installation of electric dust collectors, modification of the ash treatment system, additional installation of the re-circulation system, new installation of waste water treatment facilities, and modification of the waste water treatment equipment in the plant premises. As a result of the discussions, the annual energy saving quantity was found to be 62,936 tons of crude oil equivalent for the case where only one turbine is renewed, and 93,298 tons for the case where both of the two turbines are renewed. The annual reduction quantity of the greenhouse gas emission was found to be 251,215 tons and 372,402 t-CO2, respectively. (NEDO)

  19. Fiscal 1997 verification and survey of geothermal prospecting technology etc. 2/2. Survey report on deep-seated geothermal resources; 1997 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 2/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-02-01

    For the purpose of reducing the risk to accompany the exploitation of deep-seated geothermal resources, investigations are conducted into the three factors that govern the formation of geothermal resources at deep levels, that is, the supply of heat from heat sources, the supply of geothermal fluids, and the development of fracture systems contributing to the constitution of reservoir structures. In the evaluation and study of reservoirs and the amount of resources, a reservoir simulation is conducted to grasp the characteristics of reservoirs and the amount of resources. For this purpose, the origin and history of the Kakkonda geothermal field are studied, with special attention paid to the origin of the difference in temperature between the shallow-seated and deep-seated reservoirs, the geometry of granite at Kakkonda, the region of recharge of meteoric water, the distribution of saline concentration in the natural state and the cause of the occurrence, the amount of supply of fluids and heat from the depth to the reservoirs, etc. In the evaluation and study of the economic effectiveness of the exploitation of deep-seated geothermal resources, it is learned that, if a 50MW geothermal power station is to be built at a deep level (drilled depth of 3000m on the average) with a rate of 50% attained in drilling, the steam amount required at such a deep level (presumed to be 75t/h) will be more than twice that required at a shallow level (presumed to be 35/h). (NEDO)

  20. Fiscal 2000 survey report. On-site survey of local state of affairs such as energy efficiency enhancement (Mongolia); 2000 nendo energy shohi koritsuka nado chiiki josei genchi chosa hokokusho. Mongoru

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Information was collected and surveys were conducted in Mongolia in an effort to acquire information necessary for energy related technical cooperation. The results were arranged in four fields which are (1) the current state of economy and the future trend, (2) current state of energy production/consumption and the future trend, (3) current state of power supply/demand and power facilities and the future trend, and (4) the current state of energy efficiency enhancement and the future trend. Mongolia has a population of 2.45 million at a density of 1.57/km{sup 2}, with Ulan Bator the capital inhabited by 0.69-million people. The mean air temperature is -10 degrees C in the period November through March, which makes heating indispensable. Power stations are of the heat and power cogeneration type. Power is supplied by the Eastern, Central, and Western systems, with the Central system producing 80% or more and independent power sources 10%. Its economy has already recovered from the confusion that followed the change of its national constitution. Mongolia's demand for power lingers low, however, and its facilities can produce more electricity than what is now wanted. Energy efficiency enhancing activities should start with the upgrading, reinforcement, and maintenance of the existing facilities and with independent power sources. (NEDO)

  1. New energy vision for Ginoza village. Fiscal 2000 survey report on new energy vision formulation project for Ginoza village; Ginozason shin energy vision. 2000 nendo Ginozason shin energy vision sakutei nado jigyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A new energy vision has been formulated for Ginoza village, Okinawa Prefecture, for the realization of symbiosis with nature. It is a 5,000-strong entirely farming village situated along the eastern coast at the middle of the main island of the Ryukyus, with energy consumption of 9,982 kl in terms of crude oil in fiscal 1999. The results of activities in this connection are summarized in six chapters, which are (1) the state of the village and new energy, (2) current state of energy supply/demand and outlook for the future, (3) existing amount of new energy, (4) trends of types of new energy under study, (5) feasibility of new energy introduction, and (6) Ginoza village's new energy vision. Chapter (6) is constituted of the general principles of new energy introduction into Ginoza village and a long-term vision of new energy introduction for each field, and discusses the introducible types which are photovoltaic power generation, wind power generation, small scale hybrid power source systems, fuel cells, natural gas fired cogeneration, refuse fueled power generation, and clean energy vehicles. (NEDO)

  2. Fiscal 1997 verification and survey of geothermal prospecting technology etc. 1/2. Survey report on deep-seated geothermal resources; 1997 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 1/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-02-01

    For the purpose of reducing the risk to accompany the exploitation of deep-seated geothermal resources, investigations are conducted into the three factors that govern the formation of geothermal resources at deep levels, that is, the supply of heat from heat sources, the supply of geothermal fluids, and the development of fracture systems contributing to the constitution of reservoir structures. In fiscal 1997, a fumarolic gas test is conducted at the deep-seated geothermal well WD-1b which was drilled in the preceding fiscal year. In the test, chemical and isotopic characteristics are compared between the fluids of the WD-1b and the other existing deep-seated wells, and it is found that the fluids from the WD1b originates in surface water just like the fluids from the others and that the constitution of its gas is not greatly affected by magmatic fluids. A PTS (Pressure, Temperature, Spinner flowmeter) logging is performed to observe conditions in the well with the fluids being discharged and to know the inflow point and rate the fumarolic fluids, and the result is utilized to presume the 3-dimensional stress in the vicinity of the WD-1. An isotopic measurement of water included in the fluids is conducted to examine the origin of the geothermal fluids, constant observation and analysis of micro-earthquakes are carried out, and the fluid flow and fluid hydraulic characteristics are also studied. (NEDO)

  3. FY 1998 report on the verification survey of geothermal exploration technology, etc. 2/2. Survey of deep geothermal resource; 1998 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 2/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-12-01

    For the purpose of commercializing deep geothermal resource, a deep exploration well of 4000m class was drilled in the existing geothermal development area to survey the situation of deep geothermal resource existence and the availability. Concretely, the deep geothermal exploration well was drilled for study in the Kakkonda area, Shizukuishi town, Iwate prefecture, to clarify the situation of deep geothermal resource existence and the whole image of geothermal system. Consideration was made of the deep geothermal exploration method, systematization of deep high temperature drilling technology, and availability of deep geothermal resource. The results of the survey were summed up as follows: 1) general remarks; 2) deep exploration well drilling work; 3) details of the study. This report contained 3). In 3), the items were as follows: heightening of accuracy of the deep geothermal resource exploration method, making of a geothermal model in the Kakkonda area, study of deep drilling technology, study of deep fluid utilization technology, and making of a guide for deep geothermal resource exploration/development in the Kakkonda area. As to the technology of high temperature deep geothermal well drilling, studies were made of the borehole cooling method, mud water cooling method, survey of deterioration of casing with age, etc. (NEDO)

  4. FY 1999 research cooperation project - the research cooperation on the protection of biodiversity and sustainable use, etc. Follow-up; 1999 nendo seibutsu tayosei hozen to jizokuteki riyo nado ni kansuru kenkyu kyoryoku. Follow up

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The follow-up for the research cooperation for Indonesia, Malaysia and Thailand was conducted to make it possible that developing countries themselves protect biological resources in the tropical area, etc. and make the sustainable use of biological resources using bio-technology. In Indonesia, the follow-up was to be made for proceeding with the joint study for 'The study on the plant utilization technology - search for useful plant ingredients' reported by Professor Koshimizu, Kinki University. In Malaysia, considering that equipment is enough installed there and research leaders are very excellent, it is considered that the country is suitable for the partner of future joint research on microorganisms with Japan. Moreover, the merit in joint study is the cooperation in study of information system and culture collection. In Thailand, Japan told them that the study theme has to be made smaller toward the culture collection rich in content and the search for useful plants/bacteria. (NEDO)

  5. Research report for fiscal 1998. Basic research for the promotion of joint implementation etc. (Ryazanskaya thermal power station modification program); 1998 nendo kyodo jisshi nado suishin kiso chosa Ryazanskaya karyoku hatsudensho kaishu keikaku chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Under study is the modification of the four antiquated 300MW brown coal-fired power plants of the Ryanzanskaya thermal power station. Under the modification program, the plants will be burning a mixture of 60% coal and 40% natural gas for an increase in efficiency and for a great decrease in greenhouse gas emission. The amount of greenhouse gas emission of 6,858,592 tons/year before the modification will be reduced by 19.4% to 5,532,198 ton/year. The budget for the modification will call for 719,731,700 US dollars. EIRR (economical internal rate of return) is calculated based on the figures provided by the Russian office concerned about the current fuel cost and the current rates for the supply of electricity and heat. It is found that EIRR fluctuates depending on the ruble/dollar exchange rate. Although it does not pay at the current exchange rate, yet, when a US dollar is worth 13.0 rubles, an EIRR of 15% will realize at an availability factor of 70%. The same result is obtained when the availability factor is 80% and a US dollar is worth 14.8 rubles. There is a plan to fire the plants with 100% natural gas in the future. If the plan is implemented, a modification to incorporate gas turbine combined cycle will become feasible. (NEDO)

  6. Report on the site surveys in fiscal 1999 on the regional situations such as energy consumption efficiency improvement. The north-western part of China; 1999 nendo energy shohi koritsuka nado chiiki josei genchi chosa hokokusho. Chugoku seihokubu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper reports the site surveys in fiscal 1999 on the energy consumption efficiency improvement in the north-western part of China. Although blessed with affluent natural resources, the regional development is delayed because of geographical restrictions and harsh climate conditions. Power generation facilities include hydroelectric power plants with output of 7.81 million kW, thermal power plants with 13.89 million kW, and power wind power plants with 70 thousand kW. The demand is estimated to increase by 4.6% annually in average. Thermal power plants are those made by the former Soviet Union, having poor power generation efficiency, which is scheduled to be improved by facility modification. Automation is also behind the times. These situations have brought about low reliability, delay in building electric power network in agricultural districts, and transmission wire loss (reducing 8.1% loss to 6% is planned). The electric power charge systems also have various problems. Environmental measures are also an issue. Dissolution of energy shortage as a result of developing the north-western area can be said a key to the future development of China. Xinjiang Electric Power Company is considering wind power generation as the center of new energy utilization. Representative facilities utilize affluent wind power available in the topography of the Tenzan mountain range in the suburb of Urumqi, the facilities being made of Denmark. Photovoltaic power generation is exiguous in realizability for the time being in terms of cost. Expectation is placed on fuel cells. (NEDO)

  7. Fiscal 1999 international energy conservation model project. Report on result of demonstrative research concerning cement clinker cooling system; 1999 nendo kokusai energy shohi koritsuka nado model jigyo seika hokokusho. Cement clinker reikyaku sochi ni kakawaru jissho kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of reducing energy consumption and CO2 discharge in a cement plant in Indonesia, R and D was conducted on new clinker cooling system, high performance kiln combustion system, and technology for steady kiln operation and control, with the fiscal 1999 results reported. In the research on the optimum clinker cooling system, a new type clinker cooling system (CCS) was developed in which air beams are applied only to stationary grate rows, in an air beam type clinker cooling system where cooling air is fed to each block, with grate plates used as the air duct. This year, in an actual machine testing equipment (capacity 2,500 t/d), the whole heat recuperation area was modified for the CCS, with the operation started since February, 1999, aiming at the optimal clinker cooling effect and high heat recovery efficiency. The heat quantity for the entire system showed a decrease of 60 kcal/kg in the heat consumption rate through CCS modification, kiln burner adjustment, etc. So long as the demonstration plant is concerned, design of a new type burner and study/design for the kiln stabilization were nearly completed. (NEDO)

  8. Basic investigation on promotion of joint implementation in fiscal 2000. Energy conservation and modernization plan for Chhatak Cement Co., Ltd.; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Chhatak Cement sha shoene, kindaika keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective of saving energies and reducing greenhouse gas emission, discussions were given on a modernization plan for the Chhatak cement factory in The People's Republic of Bangladesh. The Chhatak cement factory having a nominal production capability of 267,000 tons a year uses mainly wet-type long kilns of old type, consuming a great amount of natural gas. The present plan has discussed adoption of the Japanese energy saving technologies. The technologies use a vertical roller mill for raw material pulverization, a suspension preheater and a short kiln for clinker sintering, a grate cooler for clinker cooling, and the pre-crushing system. The result of the discussions provided the prospects of reduction in the natural gas consumption at 50%, and reduction of electric power consumption at 16%. This will mean the annual reduction of about 22,000 tons as converted to crude oil. The CO2 reduction amount would reach 51,800 tons a year. The total investment amount would be US$37,327,000. The result of the financial analysis according to the case studies appears severe, wherein reduction of the various expenses is desired possibly by the finance from Japan with generous conditions.(NEDO)

  9. Report on investigations in fiscal 2000 on the basic investigation on promotion of joint implementation. Effective utilization of associated gas as CNG; 2000 nendo kyodo jisshi nado kiso chosa hokokusho. Zuihan gas no CNG to shite no yuko riyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The Back Ho oilfield is the largest oilfield in Vietnam and at the same time is producing the largest amount of natural gas (associated gas) in Vietnam. Although the majority of the associated gas has been used in the power generation plant, a large amount of surplus gas is not effectively used because of shortage of fund and technologies. Accordingly, a feasibility study has been executed for a project to compress 20% of the associated gas into CNG, and use it effectively as automobile and factory fuel. As a result of the site survey, it was found that, although Vietnam consumes less amount of energy and emits less amount of CO2, the nation has a strong interest and a large amount of knowledge about global warming and CDM because the country is subjected to large effect of warming. Furthermore, it has been reconfirmed that introducing CNG into this territory is highly effective. Discussions have been made on places of installing the facilities, effective surplus gas utilization systems, facility specifications, utilities, and number of workers. Calculations were made on approximate cost of the facilities and the running cost. As a result of the surveys and discussions, it was determined that technological support from Japan and the Yen loan for environment with low interest rate are necessary. (NEDO)

  10. Basic investigation project for energy consumption efficiency improvement in developing countries. Invitation of engineers from developing countries (Vietnam, Philippines, and India); Hatten tojokoku energy shohi koritsuka kiso chosa nado jigyo. Hatten tojokoku gijutsusha shohei jigyo (Betonamu, Philippines, Indo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The International Center of Environmental Technology Transfer has invited seven engineers from Vietnam, eight from Philippines and two from India for human resource education project for environmental preservation in developing countries. Those who were invited are administrative officials and engineers who work at administrative agents, research institutes and corporations related to energy conservation and environment preservation. In this invitation program, lecturers were invited from governmental offices, universities and corporations according to their expertise fields to carry out lectures and site training. With respect to energy conservation, lectures were given on a `summary of energy saving methods` by a lecturer invited from the Chubu Governmental Department of Trade and Industry, and on an `introduction to new energies` by Prof. Shimizu at the Engineering Faculty of the Mie University. Both lecturers emphasized the necessity of energy conservation, and importance of new energies as clean energies. The trainees showed strong interest when they visited a `cement factory` and a `coal burning thermal power plant` as the key industries. Their experience would be reflected strongly on guiding operations of factories in their own countries. 56 figs., 15 tabs.

  11. Report on fiscal 2000 survey for geothermal exploration technology verification. Survey of deep-seated geothermal resources; 2000 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    To promote the development of deep-seated geothermal resources in a rationalized way, studies are conducted about deep-seated geothermal resource assessment techniques, development guidelines, and the like. Data were collected at the Sumikawa-Onuma district, Ogiri district, Mori district, Yanaizu-Nishiyama district, and the Onikobe district, and compiled into a database to be open to the public. Studies were made about methods for estimating parameters for deep-seated geothermal reservoirs. The resultant findings indicate that, in the Uenotai and Sumikawa-Onuma districts where geothermal reservoirs are governed mainly by a fracture network, the relaxation method and extrapolation will be effective for deep-seated reservoir temperature estimation, and the ascending current analysis method and extrapolation for permeability estimation. The findings also indicate that the expanse of deep-seated reservoirs will be suitably estimated using a method similar to that applied to shallow-seated reservoirs. In the study of the estimation of the amount of deep-seated geothermal resources, it is concluded that the simplified model A will be effective in dealing with a geothermal district where there is a well-developed fracture network and the simplified model B in dealing with a geothermal district where supply of deep-seated fluid governed by an extensive fault prevails. (NEDO)

  12. FY 2000 report on the basic survey to promote the joint implementation. Conversion of raw materials in fertilizer plants and energy conservation in India; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Indo hiryo plant genryo tenkan to shoene

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As a project contributing to reduction in greenhouse effect gas emissions by introducing energy conservation technology of Japan to India and to sustainable economic development in India, study of 'conversion of raw materials in fertilizer plants in India' was made, and the results were reported. The Indian government has been controlling the retail price of fertilizer by the subsidy policy for the protection of the domestic fertilizer production. Therefore, plants, which use coal/heavy oil/naphtha with much greenhouse gas emission as raw materials, have been behind improvement and now have no competitive force in the international market. In this project, concerning ZIL's fertilizer plant, the ammonia production capacity was set at 750 t/d and the urea production capacity at 1,300 t/d, and the energy conservation technology and the conversion of raw materials from naphtha to natural gas were studied. As a result, the amount of energy conservation was 55,705 toe/y, and the amount of CO2 reduction was 245,139 t-CO2/y. Further, this project indicated that profits were expected to increase and the cash flow would change for the better. (NEDO)

  13. Basic project on the cooperation in enhancement of the international energy consumption efficiency. Survey of energy conservation potential by industry; 2000 nendo kokusai energy shohi koritsuka chosa nado kyoryoku kiso jigyo hokokusho. Gyoshubetsu sho energy potential chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of looking for measures to promote the effective energy conservation in China, the potential energy conservation amount in general plants was surveyed and analyzed by industry. Activities were made in the following fields: 1) survey of the actual state of energy in main industries; 2) energy conservation potential in the cement industry in China; 3) energy conservation potential in thermal power plants in China. In 1), survey was made on 8 industries including the iron/steel industry and oil refining industry. In 2), survey was made of the actual state of the Liulihe cement plant and Shitou cement plant. The subjects extracted were the arrangement of instrumentation equipment such as the exhaust gas analyzer needed for combustion management, improvement of the air/fuel ratio of kiln, enhancement of cooling efficiency of clinker cooler, etc. In 3), the actual state of the Qinling power plant was surveyed, and it was made clear that high efficiency of 38% or more can be maintained if the appropriate use/maintenance management is made (coal unit consumption: 383g/kWh in Qinling and 309g/kWh). (NEDO)

  14. Fiscal 1996 achievement report. Development of liquid fuel conversion technology (Feasibility study project on liquid fuel conversion); 1996 nendo ekitai nenryo tenkan gijutsu kaihatsu seika hokokusho. Ekitai nenryo tenkan kanosei chosa nado jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This article comprises Part 1 on 'surveys of gas fields fit for a new methanol manufacturing process' and Part 2 'reports on overseas surveys of gas fields fit for a new methanol manufacturing process.' In Part 1, surveys are conducted on the existence, exploitation, and the actual utilization of natural gas resources, and on the status of natural gas industry related infrastructures in the Middle East. Proved natural gas reserves in Iran were 742tcf (trillion cubic feet) as of 1996-end, which was the largest in the world next to Russia. As for Kuwaiti natural gas resources, they all accompany oil production, with the proved reserves marking 52.4tcf as of 1996-end or the smallest in the Middle East. In Egypt, there were proved reserves of 20.4tcf as of 1996-end, and further existence of 30-40tcf is predicted. Proved reserves in Yemen are approximately 15tcf. Proved reserves in Oman were 30tcf as of 1996-end. It is expected that there will be a 1.4% increase in the demand for methanol for automobiles. The annual demand for methanol for power generation is 720,000 tons. In Part 2, on-site surveys of infrastructures and the like indispensable for methanol plant installation are reported. (NEDO)

  15. Fiscal 1996 verification and survey of geothermal prospecting technology etc. 1/2. Survey report on deep-seated geothermal resources; 1996 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 1/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of reducing the risk to accompany the exploitation of deep-seated geothermal resources, investigations are conducted into the three factors that govern the formation of geothermal resources at deep levels, that is, the supply of heat from heat sources, the supply of geothermal fluids, and the development of fracture systems contributing to the constitution of reservoir structures. In fiscal 1996, the deep-seated exploration well WD-1a is sidetracked for penetration for a target newly assigned at the 3,000m-deep level. Carried out in a survey of well geology are the naked-eye and microscopic observation of core cuttings, X-ray powder method, examination of inclusions in fluids, chemical analysis of whole rocks, analysis of isotopes in minerals, analysis of core fracturing, etc. Also, data are collected from a survey of mud log, survey of water in the well before digging, and from well logging. Furthermore, pressure monitoring etc. are conducted in order to determine the interference in pressure between the deep-seated and shallow-seated wells that accompanies multiple outbursts from the Kakkonda No. 2 machine, to know the water permeability between the shallow-seated and deep-seated parts, and to grasp the anisotropy in permeability in shallow-seated reservoirs. (NEDO)

  16. FY 2000 report on the basic survey to promote Joint Implementation, etc. Survey on the energy conservation of the Lianyuan Iron and Steel Group Complex, China; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Lianyuan tekko sho energy chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of conserving energy and reducing greenhouse effect gas emission, a feasibility study was carried out of the installation of energy conservation facilities at the steelworks of Lianyuan Iron and Steel Group Complex, Loudi City, Hunan Province, China. The installation of the following facilities was studied: coke dry quenching (CDQ) equipment, coal moisture control (CMC) equipment, sintering ignition furnace equipment, cooler exhaust heat recovery equipment, top pressure recovery turbine (TRT), and hot stove exhaust heat recovery equipment. As a result of the study, the energy conservation amount was 20,000 toe/y by CDQ, 2,530 toe/y by CMC, 900 toe/y by improvement of ignition furnace in the sintering process, 12,300 toe/y by sintering cooler, 13,200 toe/y by TRT, and 10,300 toe/y by hot stove exhaust heat recovery equipment. Further, the amount of greenhouse effect gas reduction was 61,022 t-CO2/y, 7,843 t-CO2/y, 2,896 t-CO2/y, 38,060 t-CO2/y, 55,295 t-CO2/y, and 40,621 t-CO2/y, respectively. In the estimation of effects vs. expenses, the sintering ignition furnace, sintering cooler exhaust heat recovery, and hot stove exhaust heat recovery indicated the comparatively favorable values. (NEDO)

  17. Fiscal 2000 survey report. Basic survey of promotion of joint implementation, etc. Rehabilitation of KESC gas turbine power plant; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. KESC/gas turbine hatsudensho rihabiri

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    KESC (Karachi Electric Power Supply Corporation) facilities supplying electricity to Karachi, Pakistan, were examined for rehabilitation aiming at energy conservation and greenhouse gas reduction. The rehabilitation program covered power generation facilities, fuel supply facilities, instrument control systems, and their layout. Discussed were a schedule for the production, transportation, and installation of facilities, sharing of burdens between KESC and Japan, and the economic and environmental merits expected to ensue from energy conservation and greenhouse gas reduction. The results are mentioned below. Project implementation will take approximately 18 months, and Japan will be responsible only for dispatching specialists to elaborate on CDM (clean development mechanism) and engineers. In Case 1, the amount of initial investment is estimated at 84-million US dollars, the economical efficiency of energy conservation at 107t/year/million yen, and the economical efficiency of greenhouse gas reduction at 330t-CO2/year/million yen. It is found in the study of profitability that the loan will be collected in 10 years after project implementation and the initial investment in 22 years. (NEDO)

  18. Basic investigation on promotion of joint implementation in fiscal 2000. Modernization project for North Bangkok Thermal Power Plant in Thailand; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Tai North Bangkok karyoku hatsusensho kindaika jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective of saving energy and reducing greenhouse gas emission, a modernization project has been discussed on the North Bangkok heavy oil burning thermal power plant owned by Electricity Generating Authority of Thailand (EGAT). The present project plans to withdraw the existing units No. 1, 2 and 3, and install two new generating facilities with the rated output of 358.3 MW using natural gas as fuel. The present feasibility survey has performed detailed comparative discussions on four cases, whereas a proposal was selected to withdraw all of the boilers, steam turbines, and generators, and install two single axis combined cycle systems whose output has been increased by using the existing fuel tank area. The energy saving effect by this project can reduce fuel consumption annually by 514 kt of crude oil equivalent. The greenhouse gas can be reduced annually by 2,680 kt-CO2. The project will require a total fund of about 57 billion yen. The profitability assessment calls for the internal profitability of 8.413% and the investment fund efficiency of 1.69%. The economic investment payback effect of this project is determined sufficient. (NEDO)

  19. Survey report on project for drawing district energy-saving visions for Town of Aizu Wakamatsu. Preliminary survey; 2000 nendo Aizu Wakamatsu shi chiiki sho energy vision sakutei nado jigyo (shoki dankai chosa) chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    The feasibility study is conducted for introduction of the district energy-saving measures in City of Aizu Wakamatsu, for which the actual situations of energy consumption and promising energy-saving measures are surveyed. The city has a typical basinal weather, cold in winter and very hot and humid in summer, and tends to have a longer air-condition period in a year. It is considered that there are many wasteful energy consumption items to be studied for reduction. In the area of moving means, dependence on public transportation systems is considered to be relatively low, suggesting that there are much space of reducing transportation energy by the measures such as self-imposed control on use of private cars, promotion of utilizing public transportation systems and fuel-saving type driving throughout the city. The promising energy-saving measures studied to verify the effects include introduction of PVM analyzers for establishing better cost/effect relationship between power consumed by air-conditioners and pleasantness; introduction of garbage power generation, co-generation and high-efficiency illuminators; improvement of power-factor; and demand control for air conditioning, rationalization of power-receiving facilities, introduction of systems for saving flushing water and improvement of air conditioners' outdoor facilities. (NEDO)

  20. FY 1999 report on the results of the R and D on high performance industrial furnace, etc.; 1999 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In the development of high performance industrial furnace, initial targets were achieved such as energy saving of 30%, downsizing of 20%, and a remarkable NOx reduction. To verify the achievement, the test field project is being worked on by NEDO. In FY 1998, 23 heating furnaces, 29 heat treat furnaces and 6 melting furnaces were under the project at energy saving effect of 52,000 kl converted to crude oil. In FY 1999, 18 heating furnaces, 26 heat treat furnaces and 7 melting furnaces are now under the project at energy saving effect of 57,000 kl. The project was awarded 'The 9th Nikkei Global Environmental Technology Prize.' The themes for the R and D are as follows: high efficiency exhaust heat utilization system, self-completion type high temperature/high radiation heating technology, technology to make heat transfer in steel heating suitable under non-stationary state, high efficiency heat transfer technology, technology to optimize the shape of heating furnace, high performance atmosphere heat treat furnace, high efficiency heat transfer technology by high temperature jet flame heating, technology of high efficiency aluminum melting furnace, technology to improve soaking degree in steel heating, high performance tubular heating furnace in oil refining, optimum combustion control technology of regenerative burner furnace, and laser measuring method inside industrial furnace. (NEDO)

  1. New energy vision for Nomura town. Fiscal 2000 survey report on regional new energy vision formulation project for Nomura town, Ehime Prefecture; Nomuracho shin energy vision. 2000 nendo Nomuracho chiiki shin energy vision sakutei nado jigyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    An effort is being exerted to build a town which will generate but a little environmental impact, with symbiosis with nature established as the highest priority target of the town administrative activities. Under the Nomura town new energy vision, a basic policy and measures are established toward the promotion of new energy introduction, with local features, existence of new energy resources, and the feasibility of new energy adoption taken into consideration. Surveys were made and the results are compiled into seven chapters, which involve (1) the trend of new energy, (2) local features, (3) existing amount and available amount of new energy, (4) basic policy toward the introduction of new energy, (5) main projects for the introduction of new energy, (6) details of the basic policy toward the introduction of new energy, and (7) the Nomura Town Deliberation Committee on New Energy Vision Formulation. Chapter (6) covers the assessment of new energy introduction feasibility, promotion of concretized introduction projects, public relations/enlightening/popularizing activities, and assistance for new energy introduction. Studied for introduction are photovoltaic power generation, solar heat utilization, wind power generation, biomass power generation, and the like. (NEDO)

  2. Fiscal 2000 report of investigation. Project for promoting international cooperation for global environment/Project for assessment on effect of climate change; 2000 nendo chikyu kankyo kokusai kyoryoku suishin jigyo / kiko hendo eikyo hyoka nado jigyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Assessment and examination were conducted on the scientific/technological aspect, environmental aspect and economic/social aspect concerning measures for mitigating climate change, as a part of international cooperation in global warming issues. In the development of assessment methods for cost analysis, it revealed that, in the activities for mitigating emission of greenhouse effect gases (GHG) or for increasing carbon sequestration, benefits of the mitigation sometimes surpassed their cost, allowing the society to benefit from the mitigation. In the examination of problems in technology transfer and their solutions, it was found that, in order to attain successful transfer, partnership among the parties interested was essential and that each government was capable of promoting such partnership. In the assessment of various policy options, the situation in the U.S. is such that the market aspect of GHG emission permit and credit trading is rather weak because of immaturity in a legal framework on GHG emission trading and because of undefinedness in the systems of the Kyoto Protocol and in the possibility of its validation. However, the reason enterprises are actively participating in the early market is that they plan a risk-hedge for example in anticipation of tighter regulations in the future. (NEDO)

  3. 1998 Annual Study Report. Surveys on seeds for global environmental technologies, including those for energy saving; 1998 nendo chosa hokokusho. Sho energy nado chikyu kankyo taisaku gijutsu no seeds ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The energy-saving and other global environmental technologies are surveyed by collecting relevant information from various institutes, both abroad and domestic, to contribute to development of ceramic gas turbines. USA has announced a climate change plan, based on the five principles, to promote utilization of high-efficiency technologies and development of new clean technologies. UK is promoting to improve energy efficiency, along with liberalization of its energy markets. Germany concentrates its efforts in the 'Program for Energy Research and Energy Technologies.' France places emphasis on prevention of air pollution and rational use of energy. The R and D trends at public institutes, e.g., universities, for global environmental technologies are surveyed, from which a total of 14 themes are extracted as the seed technologies. At the same time, a total of 9 techniques potentially applicable to the seeds are extracted by mainly reviewing JICST and patent information, and assessed. The R&D trends of the IPCC-related researchers are also surveyed, but provide no theme directly applicable to the seeds. Most of the related themes at the private and public institutes surveyed, both domestic and abroad, are concentrated on carbon dioxide. (NEDO)

  4. Fiscal 1999 survey report. Project of promoting international cooperation on global environments/Project of assessing climate change impacts; 1999 nendo chikyu kankyo kokusai kyoryoku suishin jigyo chosa hokokusho. Kiko hendo eikyo hyoka nado jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    As part of international cooperation concerning global warming, an assessment is conducted of climate change mitigating measures, from the viewpoints of technology, environment, economy, and community, in coordination with the IPCC (Intergovernmental Panel on Climate Change) 3rd working group responsible for energy policy and technological development. It aims to contribute to the preparation of a 3rd assessment report, and covers (1) the development of an assessment technique relating to cost analysis, (2) problems in the transfer of technology and solutions for them, and (3) the assessment of various policy options. Under item (1), studies are made about modelling techniques, common parameters and their values, potentials for effect, control of warming, etc. Under item (2), factors impeding the transfer and diffusion of technology are extracted and solutions therefor and the establishment of new incentives are deliberated, with analysis and investigation focused on tasks and solutions for furthering global transfer of technology with attention paid to various specific cases. Under item (3), concrete and feasible policy options are discussed on the basis of the outcome of the above-named endeavors, in view of characteristics of each of the regions, departments, and techniques. (NEDO)

  5. Fiscal 1999 report on results. Development item, 'development of evaluation technique for biocompatibility and the like of porous materials'; 1999 nendo takozairyo no seitai tekigosei nado hyoka gijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of establishing fundamental technologies for ceramic porous materials that are excellent for artificial bone for a living body, evaluation technologies were developed for mechanical properties and biocompatibility, with fiscal 1999 results compiled. Performed for the examination of the mechanical properties were flexural test, compression test, tensile test, shearing test, torsion test, fatigue test, etc., with an evaluation testing method studied assuming that ceramic porous materials were applicable to implanting members. In the evaluation of biocompatibility, five kinds of osteoblast-like cell lines were cultured on a plastic disk and a dense hydroxyapatite disk, with adhesion and proliferation of the cells compared. Since these osteoblast-like cell lines adhere and proliferate on the surface and in the pore of hydroxyapatite, evaluation of the biocompatibility such as cell affinity was found possible with this in vitro method. With the view of obtaining principles for designing new bioactive ceramics, a method was developed for evaluating apatite-forming abilities of metal oxide gels having different compositions and structures in simulated body fluid. (NEDO)

  6. Fiscal 1999 research report. Survey on development trends of natural gas conversion technologies into liquefied fuel in Russia; 1999 nendo Roshia ni okeru tennen gas no ekitai nenryoka gijutsu no kaihtsu doko nado ni kansuru chosa kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Russia having world-largest natural gas resources is promoting the forefront basic research on liquefaction technology of natural gas, in particular, Fischer-Tropsch (FT) synthetic process positively. For 3 years from fiscal 1998, this project surveys the trend of R and D on catalytic technology for liquefaction of natural gas in Russia, and fabricates the prototype FT catalyst effective for liquefaction of natural gas at a Russian research institute to evaluate its practical applicability experimentally. In fiscal 1999, based on the research result in fiscal 1998, the project carried out continuous survey on the research activity of research institutes in Russia, the research trend of liquefaction technology and the concrete results of contract researches on catalyst, and summarized the evaluation result of research results. In addition, continuous world-wide document survey on FT synthetic process was made to confirm R and D trends based on the trend of liquefaction research projects in the world, and to collect basic information on catalytic reactors for FT synthetic process by document survey. (NEDO)

  7. Report on evaluation of research and development of methods for producing basic chemicals from carbon monoxide and other stocks; Issanka tanso nado wo genryo to suru kiso kagakuhin no seizoho no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-08-01

    This project was aimed at developing methods for producing basic chemicals from carbon monoxide and other stocks (the so-called C1 chemistry), in order to establish the techniques that could promote stable supply of basic chemicals from the new carbon resources in place of oil. It was a 7-year national project beginning in FY 1980, jointly implemented by the government, academic and industrial circles. Described herein are the overall evaluation of the results. There are several carbon resources other than oil, e.g., coal, natural gas, oil shale and tar sand. They are abundantly occurring, although unevenly, and various countries are developing these resources. They can be advantageously utilized as stocks for chemicals, after being converted into synthesis gases. In Japan, they have been efficiently developed cooperatively by national institutes, enterprises, academic circles and chemical industry, to produce the world's results, e.g., gas separation/purification techniques and new catalysts for new synthesis methods. This project was terminated because of the relaxed oil supply/demand situations and lowered crude prices in the middle of the 80's, which made stock conversion less urgent. (NEDO)

  8. FY 2000 report on the basic survey to promote Joint Implementation, etc. Project for the modernization of the Tashkent cogeneration plant; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Tashkent netsuheikyu hatsudensho kindaika keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    An investigational study was carried out of the project for energy conservation and greenhouse effect gas emission reduction by introducing the newest and most powerful gas turbine cogeneration facilities to the Tashkent cogeneration plant in Uzbekistan. At the Tashkent cogeneration plant, each of the facilities is being superannuated, which leads to lowering of operational reliability and increase in cost of repairs. In the project, studied was the introduction of the newest and most powerful gas turbine cogeneration facilities with heat output of 100 Gcal/h equivalent to that of one can of the existing hot water boiler and with generated output of 80MW. As a result of the study, obtained were the energy conservation amount of 83.9 ktoe/y and the greenhouse effect gas reduction amount of 179.7 kt-CO2/y. The initial investment amount was 10.003 billion yen. Expenses vs. effects were 8.39 toe/y-million yen in energy conservation amount and 18.0 t-CO2/y-million yen in greenhouse effect gas reduction amount. In the study of profitability, the internal earning rate was 9.24% after tax, the return yield of capital was 41.26%, and the period of ROI was 16.9 years. (NEDO)

  9. Fiscal 1996 verification survey of geothermal exploration technology. Development of the fracture type reservoir exploration method (development of the elastic wave use exploration method); 1996 nendo chinetsu tansa gijutsu nado kensho chosa. Danretsugata choryuso tansaho kaihatsu (danseiha riyo tansaho kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of exploring accurately fracture groups greatly restricting the fluid flow of geothermal reservoirs, technical development was made for applying the elastic wave exploration technology such as the high precision reflection method, VSP, elastic wave tomography to the geothermal exploration. The Okiri area, Kagoshima prefecture was selected as a demonstrative field of a typical type where the steep and predominant fracture rules the geothermal reservoir, and experiments were conducted using the high precision reflection method and VSP. Fracture models were made, and the analysis results were studied by a survey using the array CSMT/MT method and by a comparison with existing data. Reformation of the underground receiving system used for VSP and elastic tomography is made for improvement of its viability, and was applied to the VSP experiment. The treatment/analysis system of the core analyzer was improved, and cores of the demonstrative field were analyzed/measured. Further, the exploration results, core analysis results and existing data were synthetically analyzed, and fracture models of the demonstrative field were constructed. Also, effectiveness and viability of the elastic wave use exploration method were studied. 90 refs., 418 figs., 24 tabs.

  10. Fiscal 1997 research report on the data collection, evaluation and analysis in the PV power generation field test project for public facilities; 1997 nendo kokyo shisetsu nado yo taiyoko hatsuden field test jigyo ni okeru shushu data hyoka kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    As a part of the field test project for diffusing PV power generation into public facilities generally, evaluation and analysis were made on the collected data from 105 sites installed during fiscal 1993-1996. Analysis of operation characteristics was made by using parameters obtained by developing a basic equation for every component. 94% of all the sites fell under the total solar irradiation of 3.0- 4.5kWh/m{sup 2}/D. 83% of those fell under the equivalent array operation time of 2.5-4.0h/D. 70% of those fell under the equivalent system operation time of 2.5-3.5h/D. 72% of those fell under the system operation time of 9.0-12.0h/D. 78% of those fell under the effective inverter efficiency of 0.84- 0.96. 68% of those fell under the inverter load factor of 0.25-0.35. 85% of those fell under the array performance ratio of 0.7-1.0. 83% of those fell under the system performance ratio of 0.6-0.9. The generation cost decreased from 270yen/kWh in 1993 to 100yen/kWh in 1996 because reduction of an installation cost largely contributed to reduction of the total cost. (NEDO)

  11. Confirmation study of the effectiveness of prospect techniques for geothermal resources. Deep-seated geothermal resources survey report (Fiscal year 1994); 1994 nendo chinetsu tansa gijutsu nado kensho chosa. Shinbu chinetsu shigen chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Drilling and survey of deep geothermal exploration wells were conducted to grasp the existing situation of deep geothermal resource and the whole image of geothermal systems in the area where geothermal resource was already developed. In the drilling work in fiscal 1994, 4000m-class rigs and the top drive system were planned to be used for drilling of 12-1/4 inch wells, but 9-5/8 inch liners were used for drilling down to depths of 2550m or deeper since the amount of lost circulation is large and the withdrawal of devices may be very difficult. And in 8-1/2 inch wells, the well was drilled down to a depth of 2950m. As to the deep resistivity exploration technology using electromagnetic method, studies were made of a multiple-frequency array induction logging (MAIL) method, a vertical electromagnetic profiling (VEMP) method, a joint analysis method, etc. Concerning the synthetic fluid inclusion logging technology, containers were lowered into the well and a comparison was made between data of the homogenization temperature analysis of the formed fluid inclusion and those of the temperature log analysis. With relation to the making of deep geothermal structural models, revision was made according to the determination of depths of Miocene formations, Pre-tertiary formations, and the Kakkonda granite. 65 refs., 268 figs., 79 tabs.

  12. Report on FY 2000 project for drawing district energy-saving visions for Village of Satomi; 2000 nendo Satomi-mura chiiki sho energy vision sakutei nado jigy hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The district energy-saving visions are drawn for Village of Satomi, aimed at construction of an energy-saving, resources-recycling type farming village in mountains, friendly to the environments, and the implementation organization is established. The activities include (1) questionnaire survey for energy saving, with the questionnaires sent to the citizens and enterprises, (2) actual situations of energy consumption, (3) setting the hardware and software targets achievable in 5 years, (4) setting the projects for introducing energy-saving facilities, and (5) establishment of the energy-saving spreading committee, and drawing the action programs. Insufficient practices are pointed out, and necessity for the spread/enlightenment activities are clarified. At the same time, it is estimated that the energy consumption can be potentially reduced by 8% in 5 years. It is decided to introduce a co-generation system in the biomass recycling center, systems for photovoltaic power generation and production of hot water by solar heat in the integrated day-care center, and wind power system in Plateau Satomi. (NEDO)

  13. FY 2000 Project report on survey for drawing district energy-saving visions for City of Oguchi; 2000 nendo Oguchi-shi chiiki sho energy vision sakutei nado jigyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    The energy-saving visions are drawn for City of Oguchi to help spread the energy-saving practices through the citizens, based on the studies on more efficient and realizable energy-saving measures, including effective utilization of district energy. The energy-saving activities cover the following 6 areas: (1) energy demand trends and current status of energy-saving measures, (2) basic environmental conditions related to energy saving in the district, (3) prediction of energy demands, (4) basic conception of the district energy saving, and introduction methodology, (5) energy-saving implementation plans, and (6) promotion of and problems involved in introduction of the energy-saving measures. The energy-saving implementation plans cover the public facilities, household, schools and private enterprises, and the energy-saving measures studied for the public facilities include introduction of microhydroelectric power generation systems for service water and sewer systems, revolving doors for libraries, high-efficiency illumination systems, and various types of solar systems. Those for household include economic utilization of home electric appliances and automobiles, and those for cooperation by the administration and citizens include thorough separation of garbage. (NEDO)

  14. Research and development of utilization technology of solar thermal energy system for industrial and other use. International joint technology development for solar energy utilization systems; Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Taiyo energy riyo system kokusai kyodo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for international joint technology development for solar energy utilization systems. The joint study with an Indonesian research institute takes a model of lumber drying plant for the design and feasibility study. All the parts it needs are technically available in Indonesia, except carbon fiber sheets and electronic devices for controlling purposes. The drying cost is higher than that of a plant which procures charge-free wood fuel, but lower than that of a plant which procures fuel at 30$/t. A cacao drying plant model is also studied. The feasibility study shows that the initial investment for the blowing-up model is much higher by 60% to 100% than that for the conventional plant. Its fuel cost is lower by 11% than that of residual oil but 27% higher than that of wood. 4 figs.

  15. New Sunshine Project for fiscal 1997 on the international cooperation project. Cooperation in solar energy technologies among Japan, Australia and other countries; 1997 nendo new sunshine keikaku kokusai kyoryoku jigyo. Nichigo nado taiyo energy gijutsu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes the state of progress in the cooperation in solar energy technologies among Japan, Australia and other country, the memorandum concluded for the new project, and the activity report on the NEDO/MUERI project. The progress in the cooperation in solar energy technologies among Japan, Australia and other country is divided into that of the new project and that of the continued project. The former relates to the start of the long-term endurance test project for photovoltaic solar modules in Oman. The location of the endurance test is the Sultan Qaboos University in the suburb of Muscat. Modules subjected to the endurance test consist of ten modules of five types. The test will be performed on air temperature, humidity, wind directions, insolation on horizontal surface, insolation on slanted surface, ultraviolet ray intensity, module temperatures, and electric characteristics of the modules. The continued project is an outdoor endurance test for the photovoltaic solar modules begun in fiscal 1996, which is executed by the Murdock University Energy Research Institute (MUERI). The endurance test locations were selected at Darwin, Alice Springs and Perth. This paper reports the photovoltaic solar module endurance test and investigation, as well as the periodical consultations as the activity report of the NEDO/MUERI project. (NEDO)

  16. Survey on utilization of database for research and development of global environmental industry technology; Chikyu kankyo sangyo gijutsu kenkyu kaihatsu no tame no database nado no riyo ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    1993-03-01

    To optimize networks and database systems for promotion of the industry technology development contributing to the solution of the global environmental problem, studies are made on reusable information resource and its utilization methods. As reusable information resource, there are external database and network system for researchers` information exchange and for computer use. The external database includes commercial database and academic database. As commercial database, 6 agents and 13 service systems are selected. As academic database, there are NACSIS-IR and the database which is connected with INTERNET in the U.S. These are used in connection with the UNIX academic research network called INTERNET. For connection with INTERNET, a commercial UNIX network service called IIJ which starts service in April 1993 can be used. However, personal computer communication network is used for the time being. 6 figs., 4 tabs.

  17. Fiscal 1996 verification and survey of geothermal prospecting technology etc. 2/2. Survey report on deep-seated geothermal resources; 1996 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 2/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of reducing the risk to accompany the exploitation of deep-seated geothermal resources, investigations are conducted into the three factors that govern the formation of geothermal resources at deep levels, that is, the supply of heat from heat sources, the supply of geothermal fluids, and the development of fracture systems contributing to the constitution of reservoir structures. In the study of deep-seated geothermal models for the Kakkonda area, a reservoir structure model, a thermal structure model, and a geothermal fluid/hydraulic structure model are deliberated. Then, after studying the relations of the said three structure models to fracture systems, the boundary between the geothermal fluid convection region and the thermal conduction region near the 3,100m-deep level, the existence of high-salinity fluids and the depth of gas inflow, the ranges of shallow-seated reservoirs and deep-seated reservoirs, the trend of reduction in reservoir pressure and the anisotropy in water permeability in shallow-seated reservoirs, etc., a latest reservoir model is constructed into which all the findings obtained so far are incorporated. As for guidelines for deep-seated thermal resources survey and development, it is so decided that deep-seated geothermal survey guidelines, deep-seated fluid production guidelines, and deep-seated well drilling guidelines be prepared and that assessment be made of their economic effectiveness. (NEDO)

  18. Fiscal 1999 achievement report. Research and technology of important regional technologies (Development of combustion control system technology for rationalizing energy use); 1999 nendo energy shiyo gorika nensho nado seigyo system gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For upgrading and optimizing combustion control systems, research and development is conducted for materializing SiC devices capable of high-temperature operation. In the development of basic technologies common to various types of SiC semiconductor devices, XeCl excimer laser annealing is applied to SiC implanted with Al ions, and low-damage ion implantation is studied. In the development of techniques for forming SiC single crystals into substrates, warpage of 20{mu} or less, surface coarseness of 5{mu}m or less, etc., are achieved in 1-inch and 2-inch wafers. In the development of SiC sensor technology, techniques of heteroepitaxial growth of 3C-SiC on Si substrates and of 6H-SiC on 6H-SiC wafers are established and an optical sensor is built experimentally. A high-temperature UV sensor, switching device for control, rectification device for control, etc., are built of nitrogen ion implanted 6H-SiC. In the effort to develop combustion control system technology, the principle of system operation of the combustion control method proposed under this project is verified. (NEDO)

  19. FY 1999 survey report on the survey to grasp new technologies for destruction of freons, etc. in Japan; 1999 nendo Nippon no atarashii freon nado hakai gijutsu no haaku chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    At the end of 1995, a total abolition of the production of the specified freons (CFC) was achieved. In future, it will be important to proceed with the appropriate recovery/destruction of the CFC, etc. which has been used so far, not only for the protection of ozone layer, but for the prevention of global warming. For the international study of facilities (technology) for destruction CFC, etc., the Technical Assessment Committee (TAC) was installed for destruction technology of ozone layer depletion substances (ODS) under the United Nations Environment Programme (UNEP), and the destruction efficiency (DE) of ODS was set up. In Japan, more than 30 facilities are already handling the destruction of CFC on a commercial basis. The number is expected to increase by the promotion of protection of ozone layer and prevention of global warming. This survey indicated quantitatively and qualitatively based on the TAC DE what the facilities for destruction of CFC should be which were considered of domestic laws in Japan, and was made a guide for existing facilities and ones to be newly installed. (NEDO)

  20. Study of immersed heat exchange surface for high efficiency heat recovery from wire rim tires in a fluidized bed boiler; Hai tire nado kara no kokoritsu netsukaishuyo ryudosho boiler no sonai dennetsukan no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Oshita, T; Nagato, S; Miyoshi, N; Hosoda, S [Ebara Corp., Tokyo (Japan)

    1996-07-10

    In an ICFB boiler, the fluidized bed is separated by a partition into the main combustion and the heat recovery chambers. The flows in these chambers are generated by using silica sand as the fluidizing medium. To determine the overall heat transfer coefficient (HTC) of the boiler`s panel type immersed heat transfer tulles, combustion tests were performed with wire rim tires. The overall HTC of a panel tube array was lower than that of a zigzag tube arrangement. In practice, the heat absorbed by the fins makes the coefficients of either type of tube array almost identical. The air flow rate in the circulating bed at the loot Tom of the heat recovery chamber can be changed to control the overall HTC to a value virtually identical with that of a zigzag tube array. The combustion of wire rim tires leads to a buildup of wires in the zigzag array hampering the transfer of heat. Yet, the panel type array showed no buildup so that it was possible to maintain steady operation with this type of tube arrangement. 8 refs., 10 figs., 2 tabs.

  1. FY 1999 report on the results of the technology development for abatement of pollutants related to oil refining; 1999 nendo sekiyu seisei osen busshitsu teigen nado gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The technologies are developed for efficiently, economically improving quality of automobile fuels by, e.g., abatement of environmental pollutants present in the oil products. For improvement of hydrodesulfurization rate of gas oil deep hydrodesulfurization process, the catalyst components high in isomerization ability of the hard-to-desulfurize compounds are investigated, and effectiveness of zeolite is confirmed. For production of low-sulfur gas oil by hydrodesulfurization and hydrocracking of heavy oil, the catalyst with small pores is preferable for desulfurization of gas oil as the co-product of the treatment of heavy oil in the presence of catalyst for heavy oil desulfurization. For hydrocracking, the catalysts are prepared, on a trial basis, for achieving the target gas oil sulfur content of 10ppm or less by optimizing the zeolite and matrix properties. For suitability of gas oil qualities, it is found that the hydrogenation step is the rate-determining step among the reaction routes involved in the hydrogenation of difficult-to-desulfurize compounds. The data of low-sulfur gas oil qualities in Europe are collected. (NEDO)

  2. Fiscal 1997 research report. International energy use rationalization project (Analytical tool research project for energy consumption efficiency improvement in Asia); 1997 nendo kokusai energy shiyo gorika nado taisaku jigyo chosa hokokusho. Asia energy shohi koritsuka bunseki tool chosa jigyo (honpen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    Efforts have been under way to prepare inter-industry relations tables and energy data for four Asian countries, namely, China, Taiwan, Singapore and Malaysia, and a tool for energy consumption efficiency analysis has been developed and improved. In Chapter 1, energy supply and demand in the above-named four countries is reviewed on the basis of recent economic situations in these countries. In Chapter 2, bilateral inter-industry relations tables usable under the project are employed for the analysis of the economic status of each of the countries and energy transactions between them, and a method is described of converting the tables into one-nation inter-industry relations tables which meet the need of this project. In Chapter 3, national characteristics reflected on the respective energy input tables are described, and a method is shown of converting a nationally characterized unit energy table into a common unit energy input table for registration with a database. In Chapter 4, the constitution of the Asian energy consumption efficiency improvement analyzing tool and a system using the tool are explained. In Chapter 5, some examples of analyses conducted by use of the analyzing tool are shown, in which the energy saving effect and CO2 emission reduction effect are estimated for Indonesia by use of the analyzing tool. (NEDO)

  3. Report for fiscal 1999 on the fundamental survey on promotion of joint implementation. Modernization of Bakabad Cement Factory; 1999 nendo kyodo jisshi nado suishin kiso chosa Bekbad cement kojo kindaika chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes the result in fiscal 1999 of the feasibility study applied with the COP3 clean development mechanism for Bekabad Cement Factory in the Republic of Uzbekistan. One of the existing three old type kilns were diverted and converted into a dry NSP type kiln (having the same production capacity as the present of 726,000 tons a year). This arrangement was intended to enhance the productivity, save the energy, and reduce emission of greenhouse gases and different pollutants by renewing the upper and lower stream facilities and installing such environmental devices as electric dust collectors and bag filters. The total construction cost is US$84,432,000. Reducible energy consumption and reduction quantity of greenhouse gases would be 73,232 toe/year and 176,528 toe/year, respectively, in the single fiscal 2006. The cumulative quantity over twenty-year period until 2025 would be 1,464,640 toe and 3,530,560 toe, respectively. The energy saving effect per US$1,000 would be 17.87 toe, and the greenhouse gas reduction effect would be 43.08 t. In the case of using a soft loan such as the special yen loan for environment application, the internal profit rate after tax would be 7.63%, which is not high as the business enterprise profitability. However, the profit and loss statement indicates creation of profit after two years of operation, hence there is a relative realization possibility. (NEDO)

  4. Research report for fiscal 1988. Basic research for the promotion of joint implementation etc. (plan for using combined cycle at Konakovo Power Station, Russia); 1998 nendo kyodo jisshi nado suishin kiso chosa. Roshia renpo KONAKOVO hatsudensho combined cycle ka keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    On the basis of Kyoto Protocol-provided flexible measures such as joint implementation and clean development mechanisms, a study is conducted for introducing combined cycle into Konakovo Power Plant of Russia currently equipped with antiquated eight 300MW power plants constructed in the 1960's for which early renovation is necessary. The power station is an important power source connecting to the Moscow-Petersburg main. The gas turbine combined facilities to be newly installed will comprise 250MW-class state-of-the-art gas turbines arranged in four blocks, capable of a total output of 1600MW at a thermal efficiency of 58% (with simultaneous supply of heat). Four units capable of 1200MW out of the existing units will stay in operation for load adjusting. Since the price of power is set low under government control, the accounting capital/internal return rate is as low as 2.3%. The rate recalculated under the financing conditions of special yen credit for environmental protection, however, is as high as 19%, so high as to make the renovation an economically feasible project. It is expected that there will be an annual CO2 reduction of 2.3-million tons or a reduction of 57.50-million tons in 25 years (the life span of the new facilities). The renovation may be a joint implementation project to which both Japan and Russia will attach the highest priority. (NEDO)

  5. Fiscal 1998 intellectual infrastructure project utilizing civil sector functions. Development of systems for marine organism resources classification and utilization (Achievement report); 1998 nendo kaiyo seibutsu nado shigen no bunrui riyo system no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Genetic resources and databases involving microbes and the like were conserved and amplified for the reinforcement of biotechnology industries. In the maintenance of marine microalga culture collection, 16S rDNA sequences were determined for 120 strains of Cyanophyceae isolated by Marine Biotechnology Institute Co., Ltd., and databases were prepared containing the results of molecule classification, history of each strain, and pictures obtained using optical microscopes. In the maintenance of marine bacterium culture collection, methods for identifying by molecule classification bacteria separated from the sea were simplified and unified, and genera were identified for 776 strains. In the development of systems for classifying and conserving subtropical microbial resources, base sequences were analyzed for 14 strains of six kinds of microbes such as Aspergillus awamori conserved at Institute of Applied Microbiology of University of Tokyo. Other efforts included the enrichment of marine microalga collections, construction of an embryo bank system, advanced classification of microbes, and development of a DNA (deoxyribonucleic acid) analyzing system. (NEDO)

  6. Report for fiscal 1998 on commissioned operation for research cooperation related to simplified purification system for industrial waste water; 1998 nendo sangyo haisui nado no kan'i joka system ni kansuru kenkyu kyoryoku hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With an objective to serve for environmental preservation in developing countries, joint researches have been performed on anaerobic waste water treatment systems utilizing bio-technology. This paper summarizes the achievements in fiscal 1998. This fiscal year has performed the bench scale test and the operation research of an anaerobic waste water treatment pilot plant jointly with the Standards and Industrial Research Institute in Malaysia on waste waters from the vegetable fat and oil chemical industry. In the bench scale test, data were collected on the oil removing effect of the pressurization and flotation treatment, and the characteristics of the anaerobic treatment. Operation research was performed in the pilot plant by using the anaerobic waste water treatment plant and the aerobic treatment facility. In addition, a feasibility study was carried out to evaluate an optimal treatment system. Furthermore, three researchers were received from Malaysia to whom lectures were given on the Japanese anaerobic treatment technologies, and visits and operation training on the waste water treatment facilities. (NEDO)

  7. Achievement report for fiscal 1998. Development of control system technologies such as combustion with energy consumption rationalized; 1998 nendo seika hokokusho. Energy shiyo gorkika nensho nado seigyo system gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    To improve and optimize fuel control systems, basic technologies were studied for building SiC devices capable of high-temperature operation. The technologies involved the construction of single-crystal SiC substrates, development of element technologies such as conduction control, experimental production of SiC devices, and systems incorporating SiC devices for controlling, for example, combustion. The subjects of research and development for fiscal 1998 included the technologies related to common SiC semiconductor substrates (SiC substrate crystallinity evaluation by X-ray topography, thermal oxidation acceleration by ion irradiation, and annealing of ion-implanted SiC by excimer laser ), technologies of forming an SiC single crystal into a substrate, technologies related to SiC sensors, technologies related to SiC devices capable of operation at high temperature and high speed, technologies related to SiC devices for controlling, and technologies for controlling, for example, combustion. The subjects of basic researches at universities and research institutes included new crystal growing methods, ion beam-aided SiC synthesis, effect of irradiation of SiC with neutrons, and nuclear conversion implantation. (NEDO)

  8. Research report for fiscal 1998. Survey on the researchers and research institutes for the effects of global warming and its countermeasures; 1998 nendo onshitsu koka gas ni yoru kankyo eikyo nado ni kansuru kenkyusha kenkyu kikan chosa chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Researchers and research institutes across the world (except those in Japan), engaged in the study of global warming and measures to deal with the phenomenon, are extracted in compliance with certain specified standards, and the latest information on them is appropriately arranged and listed. It is further developed into an electronic database for the convenience of users. The collected information includes more than 230 research institutes and more than 1,000 researchers. The endeavor is exerted by extracting essays and institutes mainly out of the on-line databases. More than 1,000 essays and 130 institutes are covered. Visits are made to five institutes in the U.S. and four in Europe who are most actively engaged in the study of global warming, and detailed researches are conducted and information is exchanged. The Argonne National Institute copes with all energy problems related to global warming. Descriptions are given about environmental impact surveys and CO2 isolation in the ocean at the Center for Global Science of the Massachusetts Institute of Technology. At the Oak Ridge National Laboratory, the visitors heard explanations of technologies related to renewable energies and so forth. Researches are made into ecosystems at the University of California, and into natural energies at the University of Hawaii. Also visited are research institutes in Australia, Germany, Netherlands, and Britain. (NEDO)

  9. FY 1999 report on the results of the R and D on the assessment of reliability of oil refining facilities; 1999 nendo sekiyu seisei setsubi shinraisei hyoka nado gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    At present, in oil refineries in Japan, the term of the continued operation in oil refining facilities is shorter than that in Europe and America because of the regulation on the open inspection period for boilers and hazardous material storage tanks. As a result, the refining cost is comparatively higher than in Europe and America due to the increase in inspection/repair cost and decrease in operational rate. Therefore, it is becoming important to effectively supply petroleum products by keeping stability in oil refining facilities of the whole Japan and prolonging the term of the continued operation of oil refining facilities, etc. In this R and D, the technical development is conducted which is needed for the long-term continued operation of oil refining facilities. The items for the R and D are as follows: assessment technology of reliability of oil refining high temperature system facilities, assessment technology of reliability of piping/storage facilities in oil refinery, assessment technology of reliability of oil refining power system facilities, technology of management support system in oil refining facilities. In this fiscal year, technical survey, data collection, and construction of the basic concept of developmental technology were mostly conducted. Also conducted were trial manufacture of various probes for non-fracture inspection use, oscillators, etc., and basic design of inspection equipment and trial manufacture of a part of them. And the data acquired were analyzed. (NEDO)

  10. FY 2000 report on the basic survey to promote Joint Implementation, etc. Survey of gas-fired cogeneration in Samarkand City; 2000 nendo kyodo jisshii nado suishin kiso chosa hokokusho. Samarkand shi gas daki cogeneration chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In the existing heat supply plant in Samarkand City in Uzbekistan, feasibility study was conducted of the project aimed at energy conservation and reduction in greenhouse effect gas emission by introducing the repair/cogeneration system of the regional pipes superannuated. In the project, the following were planned: introduction of two units of 6MW class gas turbine cogeneration, introduction of boiler which can realize 90% of the thermal efficiency, replacement of the existing regional pipes with pre-insulated pipes with less water leak/heat loss, etc. As a result of the study, the energy conservation amount was 21,006 toe, and the amount of greenhouse effect gas reduction was 64,998 t-CO2/y. As to the effects vs. expenses, the energy conservation was 2.80 toe/million yen, and the greenhouse effect gas reduction was 8.66 t-CO2-y/million yen. The initial investment amount was 7.51 billion yen, the business profit was 468 million yen/y, and the internal earning rate was 1.133%. It was judged that great profitability was not expected for the project, but the profit was returnable on investment. (NEDO)

  11. Basic investigation on promotion of joint implementation in fiscal 2000. Project for modification of Pridneprovskaya power plant in Ukraine; 2000 nendo kyodo jisshi nado kiso chosa hokokusho. Ukraine Pridneprovskaya hatsudensho kaishu jigyo keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With objectives of saving energy and reducing greenhouse gas emission at the Pridneprovskaya power plant in Ukraine, a scrap and build project has been discussed. This project will abolish the unit No.12 among the eight units in the existing coal burning power generation facilities, and install a natural gas burning combined cycle plant comprising of three units each with an output of 100 MW. The new plant facilities will consist of gas turbines, steam turbines, HRSG and auxiliary devices, and an air-cooled synchronous power generator with a capacity of 119 MVA. Use of natural gas as fuel reduces generation of soot, sulfur oxides, nitrogen oxides, and CO. In addition, the hot effluent and waste liquor effluent will decrease from those at the present plant. The required fund will be 30,107 million yen. The energy saving effect of this project is reduction of about 7.5 million tons of crude oil equivalent as a total in 40 years. The greenhouse effect gas will decrease by about 39 million tons as a total in 40 years. The profitability estimation calls for the number of investment recovery year of 16 years, and internal profit rate of 7.32%, wherein the implementation of the project cannot be expected as a project to be carried out by private funds. (NEDO)

  12. Report on investigations in fiscal 2000 on the basic investigation on promotion of joint implementation. Rehabilitation of ICE/SAN ANTONIO power plant; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. ICE/SAN ANTONIO hatsudensho rihabiri

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Costa Rica takes a power generation system using hydro power generation as the main source, and possesses medium-capacity gas turbines to supplement needs in the dry season and the peak load. However, a problem has come up that, in addition to the cost rise in gas turbine fuel, the power generation efficiency has been aggravating due to aged deterioration of the generators being used. In association therewith, the problem is now a factor to increase CO2 emission, which is a worldwide problem. Keeping in mind to link it to the clean development mechanism (CDM), the present project is, taking up the SAN ANTONIO power plant as the investigation object, intended to perform a comprehensive discussion on the CO2 emission reducing effect, profitability, and proliferation effect, by executing the conceptual plant design. The up-grading plan for thermal power generation systems in Costa Rica consists of replacement of the gas turbines, handling of phase modifiers, and achievement of the combined cycle. The plan agrees with the present feasibility study intended of CO2 emission reduction, consisting of the modification plan of the SAN ANTONIO power plant, that is the plan to replace the over-aged gas turbines at the power plant. Its necessity has been identified. It was disclosed that the project has the effects of reducing CO2 of 82,000 tons annually, and the investment can be recovered in nine years. (NEDO)

  13. Fiscal 1996 achievement report. Development of liquid fuel conversion technology (Feasibility study project on liquid fuel conversion); 1996 nendo ekitai nenryo tenkan gijutsu kaihatsu seika hokokusho. Ekitai nenryo tenkan kanosei chosa nado jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This article comprises Part 1 on 'surveys of gas fields fit for a new methanol manufacturing process' and Part 2 'reports on overseas surveys of gas fields fit for a new methanol manufacturing process.' In Part 1, surveys are conducted on the existence, exploitation, and the actual utilization of natural gas resources, and on the status of natural gas industry related infrastructures in the Middle East. Proved natural gas reserves in Iran were 742tcf (trillion cubic feet) as of 1996-end, which was the largest in the world next to Russia. As for Kuwaiti natural gas resources, they all accompany oil production, with the proved reserves marking 52.4tcf as of 1996-end or the smallest in the Middle East. In Egypt, there were proved reserves of 20.4tcf as of 1996-end, and further existence of 30-40tcf is predicted. Proved reserves in Yemen are approximately 15tcf. Proved reserves in Oman were 30tcf as of 1996-end. It is expected that there will be a 1.4% increase in the demand for methanol for automobiles. The annual demand for methanol for power generation is 720,000 tons. In Part 2, on-site surveys of infrastructures and the like indispensable for methanol plant installation are reported. (NEDO)

  14. Fiscal 1998 research cooperation project. Research cooperation on diversity preservation and sustainable use for living organisms; 1998 nendo seibutsu tayosei hozen to jizokuteki riyo nado ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report describes the titled research cooperation. Joint R and D with Thailand, Indonesia and Malaysia was made on collection and preservation of bio-resources such as tropical rain forest, and sustainable use of them by developing countries themselves. The project includes the simple identification and preservation technology of biospecies such as microorganism, assessment and monitoring technology of ecosystem, search of useful functions of biospecies, and construction of a bio-resource information network. This project promotes conversion of excessive hunting into resource conservation in agriculture, forestry and fisheries industries, and establishment of the basis of new product development in chemical and pharmaceutical industries. This project also contributes to preparation of the basic scheme of developed countries including Japan to countries holding bio-resources in addition to industrial basis preparation of every country. Until 1997, basis establishment has been made such as training of researchers, preparation of equipment and technical guidance, and in the final 1998, various results such as extraction of promising samples from microorganisms were obtained. (NEDO)

  15. FY 1994 Report on the results of the joint research project for optimum introduction of development of fuel cell technologies for urban energy centers; 1994 nendo toshi energy center nado nenryo denchi gijutsu kaihatsu saiteki donyu chosa seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-01

    Described herein are the FY 1994 results of the joint research project for optimum introduction of development of fuel cell technologies for urban energy centers or the like. The necessary economic conditions for introduction of a fuel cell system to be competitive with the conventional system which individually supplies electric power and heat are 250,000 yen/kW as the construction unit cost, 0.10m{sup 2}/kW as the installation area, 5 years as the cell body life, use of an inexpensive fuel gas (2 to 6 yen/Mcal). Moreover, it is an indoor system which shall have the operational characteristics to follow daily demand fluctuations while operating under the optimum conditions in the urban redevelopment area considered. A 5,000kW-class fuel cell plant burning fuel gas (2 yen/Mcal) will need a total floor area of approximately 400,000 m{sup 2} in an energy-intensive office type demand area. These conditions shall be met in order to economically introduce the 5,000kW-class plant. It is also necessary to compare the plant with the competitive cogeneration plants. The specifications for the prototype now under consideration are sufficient for the energy-saving effect, and it is premised that these specifications and characteristics are secured. (NEDO)

  16. Report on achievements in fiscal 1999 of New Sunshine Project. Development of superconductor power applied technologies. Research on total system; 1999 nendo chodendo denryoku oyo gijutsu kaihatsu gyomu seika hokokusho. Total system nado no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    To deal effectively with problems being actualized in electric power systems, it is necessary to introduce superconductor technologies into power devices, and achieve higher efficiency, density and stability in the power systems. To achieve the goal, development is being made on superconductor power applied technologies, whereas investigative researches are given on the effects of introducing the superconductor power applied devices to proceed the development effectively and smoothly. This project is also given evaluations on its research achievements. In the practical application of superconductor generators, all of the verification tests have been completed, with the model generator system linkage test as the final test. Design and fabrication technologies were established on a 200,000-kW class pilot generator after having gone through analyses made after the tests. Not only having achieved the initial technical value targets, the result presented reliability required for practical use of the superconductor generator, having exceeded the expectation. The research and development of the superconductor generator technologies under this project is concluded successful. The AC superconductor devices were developed by effectively utilizing the results of the leading researches on fundamental technologies for AC superconductor power device technologies as well as other results of the world's highest levels. (NEDO)

  17. Report on evaluation of research and development of methods for producing basic chemicals from carbon monoxide and other stocks; Issanka tanso nado wo genryo to suru kiso kagakuhin no seizoho no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-08-01

    This project was aimed at developing methods for producing basic chemicals from carbon monoxide and other stocks (the so-called C1 chemistry), in order to establish the techniques that could promote stable supply of basic chemicals from the new carbon resources in place of oil. It was a 7-year national project beginning in FY 1980, jointly implemented by the government, academic and industrial circles. Described herein are the overall evaluation of the results. There are several carbon resources other than oil, e.g., coal, natural gas, oil shale and tar sand. They are abundantly occurring, although unevenly, and various countries are developing these resources. They can be advantageously utilized as stocks for chemicals, after being converted into synthesis gases. In Japan, they have been efficiently developed cooperatively by national institutes, enterprises, academic circles and chemical industry, to produce the world's results, e.g., gas separation/purification techniques and new catalysts for new synthesis methods. This project was terminated because of the relaxed oil supply/demand situations and lowered crude prices in the middle of the 80's, which made stock conversion less urgent. (NEDO)

  18. Report on the wind power development field test project in the off-shore park in Daitocho Town in fiscal 1997. System design; 1997 nendo Daitocho kaiyo koen nado ni okeru furyoku kaihatsu field test jigyo hokokusho. System sekkei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    This paper reports the wind power development field test project in the off-shore park in Daitocho Town in Shizuoka Prefecture. The annual average wind velocity was 4.2 m/s (at height of 20 m above the ground), where the facility utilization rates for 300 and 500 kW class plants were 15.1 and 16.7%, respectively. Both of the annual average wind velocity and the facility utilization rate do not meet the criteria established by NEDO. Although the location is adjacent to the Natural Park, there is no restricting condition for installation. The substation to which system linkage is to be performed is the Daito substation 3 km north of the planned location. The major load is the Daito Spa in the park facility. Ground bed at depth of 5 m will be used as the windmill foundation supporting bed. There is little electromagnetic wave hazard. The location is 380 m away from the nearest residential house, presenting no windmill noise problem. The amount of power to be generated was assumed 281,000 kWh. Specifications for nine models of 300-kW class windmills that can be introduced into Japan were discussed to select a model. The project cost was calculated to be 128.5 million yen. The construction cost will be 428,000 yen and the power generation cost 38.1 yen/kWh. Its economy is poor when the current unit price for surplus power purchase is considered, but the effect of enlightenment may be expected. (NEDO)

  19. FY 1998 basic survey to promote the joint execution, etc. Plan for repair of Schekinskaya thermal power plant; 1998 nendo kyodo jisshi nado suishin kiso chosa. Schekinskaya karyoku hatsudensho kaishu keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project is a feasibility study to get effects of reducing greenhouse effect gas by repairing Units 8, 9, and 10 (330MW in total) of Schekinskaya thermal power plant and Units 1-7 (450MW in total) of Novomoskovskaya thermal power plant. Both are very old brown coal fired thermal power plants which were constructed during 1947-1967. At present, they are run fired by natural gas. Being very superannuated, they need repair of the facilities. In the adjustment of opinions with Russia, the plan was aimed at substantial reduction of greenhouse effect gas by increasing thermal efficiency of power plant. For it, a 800MW class gas turbine combined cycle power plant is constructed at Novomoskovskaya power plant where there are existing buildings and space for equipment and where gas fuel can be used. As a result of the study, it was indicated that the reduction amount of greenhouse effect gas after the repair becomes 1,853,966 tons/yr as against 3,590,514 tons/yr before the repair. (NEDO)

  20. Fiscal 2000 survey report on technological trends. Survey on trend of high-density energy beam technology concerning conservation of energy; 2000 nendo gijutsu doko nado chosa hokokusho. Energy shiyo gorika ni kakawaru komitsudo energy beam technology no doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    There is a possibility that machining technology using high-density energy beam will bring an epoch-making change to micro-nano area processing. In particular, a laser beam having high controllability is indispensable. This is a report of the fiscal 2000 survey. The survey was conducted on laser beam generation, control and nano-diagnostic techniques, micro-nano optics technologies and machining technologies, with the development problems and targets summarized. Laser beam generation/control technologies, which become the basic tools for micro-nano manufacturing, were investigated, as were inspection technologies for the purpose of checking the functions of nano structures created. Particularly, the investigation elucidated the significance of development of a femtosecond solid state laser based on a semiconductor laser and the control techniques of their phase. Further, necessity was emphasized in developing X-ray probing, infrared and terahertz spectroscopy which are essential for nano-diagnostic techniques. In optics technologies, the paper described the importance of photonic crystals which enable less-than-wavelength machining or electrical beam control using interference effect. The possibility of fabricating photocatalysts with nano-particles was also mentioned, as was the manufacturing of nano-functional structures. (NEDO)

  1. Fiscal 1999 research report. Basic research on joint implementations promotion (Feasibility study of modification for Tehran Cement Co., Ltd., Iran); 1999 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Iran koku Teheran cement sha kaizo F/S

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The feasibility study was started upon a request made by the Iranian Ministry of Energy involving the No. 7 kiln of the above said company. It was then concluded, after assessing the degree of urgency of supply and demand and the magnitude of loss due to reduced production because of the on-site modification work, that it was not practical to begin the project immediately. Under the circumstances, various studies were made about the feasibility of modification of the whole production process of the No. 1 kiln through No. 7 kiln, and a procedure was presented, to be described below. The procedure will consist of Phase I wherein the No. 3 wet kiln is converted into an NSP (new suspension preheater) dry kiln, Phase II wherein the No. 7 SP (suspension preheater) dry kiln is converted in to an NSP kiln, and Phase III wherein the No. 4 SP dry kiln is converted into a clinker cooler. Under this procedure, the modernization of the Tehran Cement Co., Ltd., facilities will be accomplished without causing production loss. After the completion of the project, an annual yield of 3.6-million tons will be achieved, with productivity to be improved by 26.4% over the current theoretical capacity or by 54.8% over the actual average for the past 5 years. There will be a sustained conservation of 25,356 tons/year in terms of oil. Application of CDM (clean development mechanism) to this project will be extremely effective in reducing greenhouse gas and in improving profitability. (NEDO)

  2. Report on the survey in fiscal 1998. Basic survey on promotion of joint project implementation (Khabarovsk thermal power plant modification plan); 1998 nendo chosa hokokusho. Kyodo jisshi nado suishin kiso chosa (Khabarovsk karyoku hatsudensho kaishu keikaku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Discussions were given on the modification plan for Khabarovsk Thermal Power Plant as part of the basic survey on promotion of joint project implementation based on the COP3. The plan calls for shutting down the overaged power plant No. 1 (462.5 MW) and newly building the power plant No. 4 with high efficiency to reduce CO2 emission. The plant will use coal, which is mined extensively in the region. The plant will be a combined heat and power plant with a total power generation output of 576 MW and a total thermal output of 1140 Gcal/h. Effect of reducing CO2 emission as the result of this modification plan will be as much as about 1.2 million tons annually. The plant will use coal as fuel in the beginning, but if it uses natural gas in the future, for which pipeline construction from Sakhalin has been planned recently, the CO2 emission reducing effect will reach 2.4 million tons. Internal profitability was calculated with the CO2 price set at zero US dollars and with the foreign exchange rate varied, for a case of firing coal for 30 years. The profitability may vary largely according to the foreign exchange level, such as profit rate of 5.47% at 20 roubles to a US dollar, 11.04% at 12 roubles, and 21.22% at 6 roubles. The profitability should be judged somewhat low under the current exchange rate of 20 roubles to a dollar. Financial provision with a favorable condition is strongly desired. (NEDO)

  3. Basic investigation on promotion of joint implementation in fiscal 2000. Efficiency improvement project for gas turbine power plant in Iran; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Iran gas turbine hatsuden plant no koritsu kaizen project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Investigations and discussions have been given on measures to improve energy conservation and efficiency at a power plant of Kish Water and Power Company (KWPC) in Iran. The site has high ambient temperature throughout a year, making the gas turbine power plant capable of generating power only at about 70% of the rated output, with the power generation efficiency decreasing. The project has analyzed the current situation at the plant, and evaluated different means that appear effective in improving the efficiency, including the gas turbine absorbed air cooling system, the steam injection system, and the combined cycle. As a result of the discussions, it was revealed that energy saving effect can be obtained at 145 TJ with the gas turbine absorbed air cooling system, 224 TJ with the steam injection system, and 1017 TJ with the combined cycle. The annual reduction of greenhouse gas emission due to the above energy conservation would be about 11 thousand tons, 16.5 thousand tons, and 75 thousand tons, respectively. However, the investment payback period would be about 2.45 years, 8.31 years, and 14.21 years, respectively. Therefore, the profitability does not appear very attractive because of low fuel unit cost. (NEDO)

  4. Fiscal 2000 achievement report. Development of technologies for waste treatment and recycling (Development of technologies for appropriate treatment of air bags); 2000 nendo haikibutsu recycle kanren gijutsu kaihatsu seika hokokusho. Air bag tekisei shori gijutsu no kaihatsu nado

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A centralized treatment process respecting environmental protection and safety for unused air bags aboard disused automobiles is developed. In concrete terms, a heating facility owned by Daicel Chemical Industries, Ltd., is used, which includes an apparatus for examining exhaust gas dioxins and an exhaust gas treatment apparatus and, with this facility, studies are made for appropriately treating waste gas and waste water to be generated when air bag modules undergo centralized heating. Endeavors in fiscal 2000 center about (1) the development of waste gas treatment technologies, (2) development of waste water treatment technologies, (3) chemical analysis of waste water sludge, dusts and air bag residues, and (4) the study of appropriate treatment of non-azide air bag modules. As to the development of exhaust gas treatment technology, it was proved that the exhaust gas treatment system consisting of secondary incineration furnace, exhaust gas cooling tower and bag filter worked effectively. (NEDO)

  5. FY 1998 report on the results of the development in recycling technology for building materials such as waste concrete; 1998 nendo hai concrete nado kenzai recycle gijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For increasing fields of application of concrete rubble discharged as construction waste, the recycled aggregate is recovered by heating and rubbing/grinding. To meet the recycling demand effectively, a unit was made a transfer type. Equipment with treatment capacity of 3 tons/h was manufactured and confirmed of its motion. As to the heating equipment, the low-energy consumption structure aiming at homogeneous filling and appropriate ventilation was adopted to control uneven heating and increase in packed bed pressure loss. A tube mill type of the coarse aggregate recovery device was designed/manufactured considering the size of medium and discharge of mortal particles. An attriter type was designed/manufactured considering smooth particle discharge. As to the fine aggregate recovery system, a tube mill type was designed considering the discharge of powder and using coarse aggregate as medium. Moreover, the appropriate transportation of the generated powder and storage method are also considered. The transfer type equipment (unit frame, etc.) was designed/manufactured to make it a unit considered of layout at the time of transporting and assembling the auxiliary equipment such as supply hopper. The noise prevention device was also equipped with. (NEDO)

  6. Fiscal 1998 research report on the development trends of natural gas conversion technologies into liquefied fuel in Russia; 1998 nendo Roshia ni okeru tennen gas no ekitai nenryoka gijutsu no kaihatsu doko nado ni kansuru chosa kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Russia having natural gas resources largest in the world is actively promoting the basic research on liquefaction technology of natural gas such as Fischer-Tropsch (FT) synthetic catalyst, and its research potential is extremely high. This 3-year research project surveys the R and D trends of catalyst technology for liquefaction of natural gas, and fabricates the prototype FT synthetic catalyst based on the idea of Russian researchers to evaluate its feasibility experimentally. This report summarizes the following to clarify the research background: (1) The technology system for liquefaction of natural gas, and its future R and D trend, (2) The R and D trends of liquefaction technology of natural gas in the world, (3) The R and D trends of liquefaction technology of natural gas in Russia, (4) The research system of catalyses in Russia, (5) The activities of Russian catalysis research institutes, (6) The fuel liquefaction technologies of Russian major research institutes, and (7) The proposals from Russian research institutes. (NEDO)

  7. Fiscal 1998 research report on development of the advanced industrial furnace (R and D on the advanced industrial furnace). Volume 3; 1998 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report summarizes the research results of the chapter 4 and 5 (experimental database) from the research report on development of the advanced industrial furnace. The chapter 4 summarizes functions of the temperature performance evaluation simulator of the advanced continuous heating furnace for the database system, and various research results obtained by the simulator. This chapter also summarizes the research result on the applicability of high-temperature air combustion to other industries, the patent research result on heat storage combustion technology, the basic technology research result, and the reaction analysis result by FLUENT. The chapter 5 summarizes the combustion experiment data collection by developing self-completion high-temperature high-radiation heating technology. As for R and D on technology optimizing the profile of heating furnaces, the following data are summarized: measurement data of heat transfer in furnaces and heat flux data at right overhead furnace temperature under cold air and preheated air combustion in conventional furnaces, and heat storage combustion. (NEDO)

  8. International measures project for rational energy use (Survey project of the analysis tool of Asian energy consumption efficiency). List of errata; 1998 nendo kokusai energy shiyo gorika nado taisaku jigyo seigohyo. Asia energy shohi koritsuka bunseki tool chosa jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The list of errata was prepared for the data book of the international measures project for rational energy use (Survey project of the analysis tool of Asian energy consumption efficiency). Corrected pages of the data book 1 (1990) are as follows: 187-190, 223-226, 259-262, 295- 298, 369-370, 387-388 and 405-406 on Malaysian data. Corrected pages of the data book 2 (1985) are as follows: 102-105 on Chinese data, 154 on common data, and 187-190, 223-226, 259-262, 295-298, 369-370, 387-388 and 405-406 on Malaysian data. (NEDO)

  9. Report on fundamental surveys for such as cases and effects in relation with development of new energy technologies in fiscal 1999; 1999 nendo shin energy gijutsu kaihatsu ni kakawaru jirei koka nado kiso chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes the fundamental surveys in fiscal 1999 on cases and effects in relation with development of new energy technologies. Among the projects having been performed by NEDO in commemoration of the 20th anniversary of the NEDO foundation, the economic and social situations in the times in which the projects have been carried out with the focus placed particularly on new energies were put into order and analyzed to make clear the positioning of the project significance in the nation's energy policies. In addition, the roles of NEDO were recognized afresh to use them as the fundamental materials to serve for the future policy development. For the past thirty years before and after the oil crises, the time division that can be used universally for the project evaluation was established, based on the trends inside and outside the country, social currents, related indexes, and the status of development execution. Work hypotheses were presented regarding the basic conception in the evaluation, specific evaluation viewpoints, and their contents. Based on the hypotheses, three subjects were taken up as representative cases, that is, photovoltaic power generation, coal liquefaction, and phosphoric acid type fuel cell technology development. Time points that are considered as the important turning points were specified to give evaluations at respective turning points. Analyses were also made on decision making factors for project planning, continuation, direction change, suspension, and completion. (NEDO)

  10. FY1999 technological development of wind power generation systems for islands. Development of wind power generation systems in islands; 1999 nendo ritoyo furyoku hatsuden system nado gijutsu kaihatsu. Rito ni okeru furyoku hatsuden system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective of developing wind power generation systems that suit small to medium size islands in Japan, conceptual design was made on a 100-kW class wind mill to satisfy such requirements as no need of large heavy machines, and gust resisting performance. Investigations were performed on sites suitable for demonstration tests thereof. This paper reports the achievements in fiscal 1999. In investigating the site location feasibilities, which took small to medium size islands in Okinawa Prefecture as the discussion objects, environmental investigation, wind condition forecast and investigation, and system linkage investigation were carried out, whereas one point each in three islands were extracted as the promising sites. The system discussion and design called for wind velocity resistance of 80 m/s, system linkage percentage of 40% at maximum, power generation cost of 20 yen per kWh, design life of 20 years, constructability of requiring no large heavy machines, and operation mode of diesel hybrid use. Along with these specifications, conceptual design was performed on the system constituting elements, such as wind mill blades, generators, electric power control devices, and towers. In the blade aerodynamic test, wind tunnel tests were executed by using three types of blade wings. Sample blades were fabricated for the preparation of blade material tests. (NEDO)

  11. Fiscal 1998 research report on information structuring technology for advanced use of NEDO research reports; 1998 nendo NEDO seika hokokusho nado no kodo riyo ni hitsuyona joho kozoka gijutsu no chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Research was made on electronic NEDO research reports corresponding to the recent extending trend of Internet. The logical structure and electronic format of NEDO research reports as document were first studied considering document disclosure and reuse of technical information. HTML as electronic format for Internet is unfortunately insufficient to describe the logical structure of NEDO research reports because of HTML's restricted description. Thus, XML which is being watched because of its possible definition of original tags was studied in place of HTML. As a result, because at present preparation of standards on XML and a compatibility for implementation of standards are insufficient, it was concluded that construction of the electronic document system for NEDO research reports is still too early. However, since adoption of XML as document format is important from the viewpoint of a property succession on Internet, preparation of the XML format file of NEDO research reports is essential. (NEDO)

  12. Survey on actual status of R and D fund assistance in the U.S.A.; Beikoku ni okeru kenkyu kaihatsu shikin enjo no jittai nado ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    As a basic survey to serve for establishment of science and technology policies, a survey was carried out on the actual status of R and D fund assistance in the U.S.A., roles of the government and civil sectors, and how they are interrelated. The survey was performed in detail on the following items: the assistance and cooperation measures taken by the U.S. government, and technological policies of the U.S. government; fund subsidies and policies toward technological research and development provided by the U.S. government; research and development plans and projects being the object of the subsidies given by the U.S. government; assistance and cooperation of private organizations for financing research and development activities in the U.S.A.; cooperation and joint works among industries, the government and universities (research consortiums) in the research and development activities; legal assistance policies for research and development in the U.S.A., the favorable tax system for research and development, the 1984 National Joint Research Act, and the actual status and analysis of the legal assistance policies in the U.S.A. for aiding research and development tests. (NEDO)

  13. FY 2000 report on the basic survey to promote the joint implementation. Project on the repair of the Bobovdol thermal power plant, Bulgaria; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Bobovdol karyoku hatsudensho kaishu jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As to the Bobovdol thermal power plant, Bulgaria, a plan for repair of power plant was worked out with the aim of energy conservation and greenhouse effect gas emissions, and the results of the feasibility study were reported. The existing power plant, 3 x 210MW unit, totals 630MW, approximately 130,000 hours in cumulative operation hour. In the repair plan, the plant is replaced with high efficiency gas combined cycle power generation facilities based on gas turbines by scrap and build. In the plan, the repair of existing units Nos. 1 and 2 for life elongation is urgently conducted, and new facilities are to be built every 5 years. As a result of the study, the energy conservation effect will be reduced by 16.37 million toe tons in 41 years after the repair, and the CO2 emission will be reduced by 105.18 million tons in 41 years after the repair. As to the profitability, the internal economical profitability is 5.66% in case of setting the CO2 emission trade at zero. This is the level on which the project is barely profitable by soft loans raised by Japan Bank for International Cooperation (JBIC), etc. (NEDO)

  14. Surveys for promoting development of overseas coals in fiscal 1999. Surveys on international coal situation; 1999 nendo kaigaitan kaihatsu kodoka nado chosa (kaigaitan kaihatsu sokushin chosa). Kokusai sekitan jijo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Detailed surveys were performed on Britain, Germany and Spain being the major coal producing countries in Europe with regard to a general view on the status of energy demand and supply, the status of demand and supply of coal, business institutions, and related policies in each country. The status of demand and supply of coal, and related policies in the three countries may be summarized as follows: In Britain, the ratio of coal accounted for in the primary energy supply is 18.0% in 1998, and the coal production amounted to 35.5 mill.TCE/year; closure of underground mining coal mines is discussed recently; the congress is deliberating re-introduction of the subsidy system which had been once discontinued; in Germany, the ratio of coals accounted for in the primary energy supply in 1997 was 14% in bituminous coal and 11% in brown coal; the quantities of production of bituminous coal and brown coal in 1998 were 41.8 and 50.6 mill.TCE/year, respectively; the number of mines has decreased because of the unification; the subsidy policy is in continuation; in Spain, the ratio of coal accounted for in the primary energy supply was 13.5% in 1997 and the quantity of coal production in 1998 was 12.5 mill.TCE/year; unification of coal operators has not been advanced as far as in Germany; and the subsidy is provided as in Germany. (NEDO)

  15. Report for fiscal 1994 on commissioned operation for research cooperation related to simplified purification system for industrial waste water; 1994 nendo sangyo haisui nado no kan'i joka system ni kansuru kenkyu kyoryoku hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    With an objective to serve for environmental preservation in developing countries, joint researches have been performed on anaerobic waste water treatment systems utilizing bio-technology. This paper summarizes the achievements in fiscal 1994. In the research cooperation with Thailand, a reactor applicability test was performed by using a pilot plant to determine the operating conditions, and necessary data were obtained. The pilot plant was completed of installation in November. In the research cooperation with Indonesia, Tofu manufacturing waste water was selected as the object of pilot plant research. In the detailed design the Tofu manufacturing waste water shall be treated anaerobically, and the kitchen waste water shall be treated aerobically to acquire the intended water quality. In the research cooperation with Malaysia, as a result of visiting six industries and 22 factories for investigation, waste waters from chemical and foodstuff factories were selected as the object waste waters for the research. Three researchers from Thailand and Indonesia respectively were received in Japan to provide education including experimental training and visits to waste water treatment facilities. (NEDO)

  16. FY 1999 research cooperation project - the research cooperation on the protection of biodiversity and sustainable use, etc. Follow-up; 1999 nendo seibutsu tayosei hozen to jizokuteki riyo nado ni kansuru kenkyu kyoryoku. Follow up

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The follow-up for the research cooperation for Indonesia, Malaysia and Thailand was conducted to make it possible that developing countries themselves protect biological resources in the tropical area, etc. and make the sustainable use of biological resources using bio-technology. In Indonesia, the follow-up was to be made for proceeding with the joint study for 'The study on the plant utilization technology - search for useful plant ingredients' reported by Professor Koshimizu, Kinki University. In Malaysia, considering that equipment is enough installed there and research leaders are very excellent, it is considered that the country is suitable for the partner of future joint research on microorganisms with Japan. Moreover, the merit in joint study is the cooperation in study of information system and culture collection. In Thailand, Japan told them that the study theme has to be made smaller toward the culture collection rich in content and the search for useful plants/bacteria. (NEDO)

  17. Fiscal 1998 research report. Survey on R and D, and application technology of biotechnology; 1998 nendo chosa hokokusho. Bio technology no kenkyu kaihatsu, sangyoka gijutsu nado ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Survey was made mainly on use of biotechnology as resource saving and energy saving processes. Biotechnology is in wide use in a pharmaceutical field, while its application is on the increase in agriculture, food, chemistry, energy and environment fields. The USA is ahead of Japan and Europe. In the USA, there are more than 1000 ventures, and R and D of biotechnology, in particular, gene analysis and manipulation techniques are in progress together with acquisition of patents. In biomass energy, production of ethanol from corn, and development of biodiesel are in progress in the USA and Europe, respectively. Use of biomass should be promoted because of its global environment compatibility and sustainable productivity. In the future bio-market, genome analysis and its application are most important, however, Japan is behind in such technology in the world. The Joint approach by industry, university and government is necessary from the viewpoint of a future marketability and international competitiveness. Promotion of a public acceptance and nurture of creative talents are also important. (NEDO)

  18. FY 2000 report on the basic survey to promote Joint Implementation, etc. Survey on the repair plan for Fenchugangi fertilizer plant in Bangladesh; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Bangladesh koku Fenchugangi hiryo kojo kaishu keikaku chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of conserving energy and reducing greenhouse effect gas emission, survey was conducted for the repair plan for Fenchugangi fertilizer plant in Bangladesh. In the survey, studied were measures to increase production, measures to prolong the plant life, energy conservation measures and environmental measures. As a result of the study, it was confirmed that if the production amount targeted at first is recovered and the consumption amount of natural gas can be reduced down to the original target by rehabilitating the superannuated equipment/machines and by supplying/preparing the spare parts in shortage, the reduction in greenhouse effect gas emission is achieved and the production cost of urea fertilizer is lowered. Further, it was found that by carrying out this, energy efficiency can be heightened at the parts which can be replaced with the newest processes. The energy conservation amount calculated was 25,890 toe/y, and the amount of greenhouse effect gas reduction 60,448 t-CO2/y. The investment amount was approximately $19,106,000. The total interest is to be raised by soft loan, and the internal earning rate was 9.04% with the present prices of natural gas and urea. (NEDO)

  19. FY 1998 basic survey to promote the joint execution, etc. Overall repair plan of thermal power plants in Maritime Province of Russia; 1998 nendo kyodo jisshi nado suishin kiso chosa. Roshia Enkaishu ni okeru karyoku hatsudensho sogo kaishu keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For thermal power plants in Maritime Province of Russia, a repair plan for effective reduction of emission of greenhouse effect gas was worked out as a draft plan for the joint execution. The project is to be implemented for the additional installation/replacement of boilers at Vladivostok No. 2 power plant, construction of a power plant as a substitute for Partizansk power plant, and new construction of Ussuriisk power plant. The draft plan includes the new installation of two gas-fired boilers/replacement of existing boilers at Vladivostok No. 2 power plant, construction of 200MW cogeneration facility at Partizansk power plant, construction of 180MW cogeneration facility at Ussuriisk power plant, abolition of small-sized boiler station, etc. The reduction amount of the greenhouse effect gas emission based on this repair plan totaled 338 million tons in project. The effect against cost is US$ 4.75 per 1 CO2 ton at Vladivostok. (NEDO)

  20. FY1998 survey report on the site surveys on regional situations in improvement in energy consumption (Cambodia and Bangladesh); 1998 nendo energy shohi koritsuka nado chiiki josei genchi chosa hokokusho (Cambodia, Bangladesh) chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In order to promote technical cooperation of Japan with Asia in the energy aspect, site surveys were carried out on improvement in energy consumption efficiency. Electric power supply in Cambodia is made mostly from EDC, whose power generation amount in 1997 was 310 million kwh, while the power sold was 230 million kwh, with 26.1% of the total generation amount, or 80 million kwh being wasted as the loss. Existing power generation facilities are old and small in scale, made by the former Soviet Union making the repair difficult. The loss is enormous because of aging in power distribution facilities, overload operation, and power stealing. The efficiency is extremely poor, whereas improvement in efficiency of the existing facilities is indispensable to cope with the anticipated increase in the demand. In Bangladesh, 90% of the power is generated by using natural gas produced in the eastern part of the country. Many power plants are experiencing decreased efficiency due to the facility aging and insufficient and improper maintenance. The power transmission and distribution departments have had a large loss in power, which has become one of the most important issues. The loss exceeds 30%. The government is trying to achieve efficiency improvement in the electric power business through introducing the principle of competition by establishing new private companies. However, this approach is facing severe objection from the governmental and public labor unions, making the future development opaque. (NEDO)

  1. Fiscal 2000 achievement report. Development of comprehensive technologies for environmental conservation including prevention of global warming by the carbonization of wood, etc.; 2000 nendo jumoku nado no tanka ni yoru ondanka boshinado fukugo kankyo taisaku gijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are exerted to develop new technologies whereby carbon dioxide is absorbed by and fixed in rapidly growing trees. The trees are felled and subjected to high-efficiency carbonization, and the thus-obtained carbonized material is used for environmental purification or the like and then buried in the ground. Studies are under way to find out if the cycle (operations) may be organized into an industry. Activities are conducted in the five fields of (1) carbonized materials, (2) carbonization, (3), industrial use of charcoal, (4) stabilization of charcoal, and (5) reports on surveys (mainly overseas). In field (2), following an introduction consisting of the carbonization mechanism and the definition of terms, surveys are conducted of the existence of carbonizable resources in Japan, distribution channels of imported charcoal and activated charcoal in Japan, various carbonization apparatuses, carbonization equipment incorporated into gasifying fusion furnaces, carbonization furnace as a system, and the trends of development of pyroligneous acid and development of its use. In field (3), studies are made on its use in industries, on its application to agriculture, forestry, and livestock industry, and on the utilization of its electromagnetic properties. (NEDO)

  2. Fiscal 1999 report on results. Development item, 'development of evaluation technique for biocompatibility and the like of porous materials'; 1999 nendo takozairyo no seitai tekigosei nado hyoka gijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of establishing fundamental technologies for ceramic porous materials that are excellent for artificial bone for a living body, evaluation technologies were developed for mechanical properties and biocompatibility, with fiscal 1999 results compiled. Performed for the examination of the mechanical properties were flexural test, compression test, tensile test, shearing test, torsion test, fatigue test, etc., with an evaluation testing method studied assuming that ceramic porous materials were applicable to implanting members. In the evaluation of biocompatibility, five kinds of osteoblast-like cell lines were cultured on a plastic disk and a dense hydroxyapatite disk, with adhesion and proliferation of the cells compared. Since these osteoblast-like cell lines adhere and proliferate on the surface and in the pore of hydroxyapatite, evaluation of the biocompatibility such as cell affinity was found possible with this in vitro method. With the view of obtaining principles for designing new bioactive ceramics, a method was developed for evaluating apatite-forming abilities of metal oxide gels having different compositions and structures in simulated body fluid. (NEDO)

  3. Basic survey project for joint implementation. Feasibility study for the diffusion of fluidized bed cement kiln system in China; 1998 nendo kyodo jisshi nado suishin kiso chosa. Chugoku ni okeru ryudosho cement kirun fukyu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Discussions were given on conversion of shaft kilns mainly used at Tianjin Cement and Huaxin Cement to the fluidized bed cement kiln of the most advanced type. Possibility of energy conservation in China, that is reduction of carbon dioxide emission, was evaluated. This system has been developed by the Center for Coal Utilization, Japan. The system is characterized by reduction of greenhouse effect gas emission, elimination of the problem of dust scattering from sintering facilities, stabilized production of high-quality clinker, capability of using low-grade coal and anthracite, and reduction of cement production cost. As a result of the discussions, the reduction rate of greenhouse effect gases was found about 17 to 33%. The cost effect may be calculated as 2 to 5 thousand yen per ton of CO2 reduction amount assuming the system life of 20 years. If this process has been diffused into China, the quantity of CO2 to be reduced will reach about four million tons annually assuming a diffusion rate of 10%. This project shows as high profitability as about 20% at IRR, and the system is more advantageous economically than the shaft kiln. (NEDO)

  4. Report on research results of the development of high efficient boilers in fiscal 1996. Research development of high efficient industrial furnaces, etc; Koseino boiler no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Out of the developments of high efficient boilers which have been continued since fiscal 1993, the paper reported the result of the development conducted in fiscal 1996. The oxygen combustion (the oxygen enrichment combustion including 100% oxygen combustion) decreases the amount of flue gas and reduces heat loss of the flue gas, and is also effective as NOx reduction measures. The experiment was conducted using testing furnace. The boiler efficiency rapidly increased with the increasing concentration of oxygen enrichment. In the pure oxygen combustion, the overall boiler efficiency of a 106% level (low heating value standard) is expected. Since the boiler wet flue gas is decreased, the NOx emission is reduced. The boiler can raise the combustion temperature with no fear of NOx and can be reduced in size. CO2 decreases in proportion to the energy saving effect. The development of a condensation flue gas heat exchanger is aimed at recovering heat down to the low temperature. Prediction of heat transfer in the steam condensation region becomes possible, and the size reduction can be expected. Dew point corrosion resistant materials were also selected. As to the high speed combustion control, a simple type using micro-processor was developed. Obtained were high speed, compactness, electric power saving, and high controllability. 14 refs., 306 figs., 88 tabs.

  5. FY 2000 report on the basic survey to promote Joint Implementation, etc. Upgrading of energy utilization in the cement production process; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Cement seizo kotei ni okeru energy kodoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    An investigational study was conducted of a project for energy conservation and greenhouse effect gas reduction by introducing the steam injection gas turbine generator to production facilities of the Siam Cement Industry Corporation (SCI) in Thailand. In the project, studies were made on the following: no purchases of electric power by introduction of the steam injection gas turbine generator; additional heating by gas turbine exhaust gas by introduction of the kiln combustion air heater; remodeling of the preheater of raw materials, and the partial calcination before kiln sintering by introduction of the calcination furnace. As a result of the study, the energy conservation amount was 1,200 toe/y, and the greenhouse effect gas reduction amount was approximately 8,000 t-CO2/y, which led to the reserve power for increased production of clinker by about 18%. The size of investment was 314.5 million Baht in total. As to the evaluation of economical efficiency of the investment, the actual period of ROI was a little less than 5 years, and the internal earning rate was 17.7%, which substantially met with SCI's standards for equipment investment. However, there are problems on the gas supply infrastructure, recovery of the white cement demand, etc. (NEDO)

  6. FY 1999 report on the results of the R and D of the environmental technology of recycling, etc. 1; 1999 nendo recycle nado kankyo gijutsu kenkyu kaihatsu seika hokokusho. 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of reducing environmental loads of waste and recycling waste, etc., the R and D were carried out, and the FY 1999 results were summarized. In the study of the technology for high-grade recycling of PET bottles, construction work for stabilization of the quality of drainage water was done of a demonstration plant with a treating capacity of 8,000t/y which was constructed in FY 1996, and the stability in long-term operation was examined. In the survey of fluctuations in flake quality, the verification data indicated that the plant could be stably operated. As to the alteration of the bottle cleaning process from wet method to dry method, stabilization of the label separation performance was recognized. By the above-mentioned matters, the technology to recycle/treat PET bottles was established. In the development of the technology to recycle waste plastics which are difficult to treat, assessment was made of the treatment capacity in dry distillation gasification furnace of shredder dust and gasification characteristics. As to the removal of wire harness, separation of glass from fine copper wire, etc., methods which are promising were proposed, and it was concluded that those were not valid as a treatment method in the plant scale in terms of economical efficiency. (NEDO)

  7. Fiscal 2000 report on entrusted follow-up project for research cooperation on simplified industrial wastewater purification system; 2000 nendo sangyo haisui nado no kan'i joka system ni kansuru kenkyu kyoryoku follow up gyomu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The Research Cooperation Project on Simplified Industrial Wastewater Purification System carried out in cooperation with Indonesia and Malaysia was terminated in fiscal 1998. A follow-up check was conducted for spreading the fruits of the project. In concrete terms, for the study of problems to solve for the dissemination across Malaysia of the results of the project implemented in that country, technical guidance was provided relative to the study of operation performed by the counterpart operating their own pilot plant and the like. International Meeting for Technical Exchange was participated in, convened in Thailand in the period March 6-8, 2001. The contents of research activities included the two fields of (1) the selection of coagulants and (2) the study of pilot plant operation. In field (1), PAC (poly-aluminum chloride) and aluminum sulfate were compared with each other in terms of performance and cost in case they were used as coagulants, and then it was made clear that PAC was superior. In field (2), operation was studied using UASB (upflow anaerobic sludge blanket) type facilities of Southern Acid Plant. (NEDO)

  8. Study on ease of handling automobile secondary controls. Part 1. Procedure to seek numbers on radio station selecting buttons; Radio, eakon nado no sosasei. 1. Radio senkyoku button no shikibetsu

    Energy Technology Data Exchange (ETDEWEB)

    Ikemura, S [Meijo University, Nagoya (Japan); Noda, K [Ryowa Sheet Metal Processing Co. Ltd., Aichi (Japan); Nozaki, H

    1997-10-01

    Times to recognize the numbers on the radio station selecting buttons about horizontal straight 6 layout were measured using electro-oculogram. There are two kinds of basic pattern to seek numbers. One is that recognition times of both end numbers are shorter than those of central numbers. The other is that recognition times of all numbers are nearly same. How the subjects seek the numbers was studied using the amount of information and entropy. 6 refs., 8 figs., 5 tabs.

  9. Fiscal 1998 research report. Popularization project of the proper treatment technology of industrial wastes in Asian regions; 1998 nendo chosa hokokusho. Asia chiiki sangyo haikibutsu tekiseika shori gijutsu nado fukyu sokushin jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Study was made on popularization of the proper treatment technology of industrial wastes in Asian regions. In principle, industrial wastes should be recycled in a country concerned, however, because of a difference in technology and industrial location, treatment of all industrial wastes in a country concerned is impossible. International cooperation is thus indispensable to promote proper efficient practical measures for environment. For studying the possibility of the international cooperation between Japan and Asian countries concerned for further recognition and solution of industrial waste problems, 'International Symposium on the Asian Industrial Waste Issue' have been held in Tokyo since 1997 for governmental staffs. In fiscal 1998, Malaysia was invited in addition to China, Philippines and Thailand for popularization of the proper treatment and recycling of industrial wastes in Asian regions. In every Asian countries, poor collection of discharge, treatment and disposal data is an obstacle to effective treatment. Technical cooperation and financial support by developed countries are demanded. (NEDO)

  10. Reports on research achievements in developing high-performance industrial furnaces in fiscal 1998 (Research and development of high-performance industrial furnaces). Volume 1; 1998 nendo koseino kogyoro nado ni kansuru kenkyu kaihatsu seika hokokusho. 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    From the reports on research achievements in developing high-performance industrial furnaces in fiscal 1998, the report volume 1 was prepared as a research achievement report of each working group, detailing fundamental researches, heating furnaces, and heat treatment furnaces. The fundamental researches have researched combustion evaluating technology, characteristics of the area in the vicinity of a combustor, characteristics of combustion of high-temperature air, heating characteristics of a furnace to investigate effect of local heat absorption, and combustion evaluation. For the heating furnaces, the following subjects were studied: development of an in-furnace combustion model, summary of an experiment for evaluating high-temperature air combustion, furnace height relative to combustion heat transfer characteristics, heat loss minimizing technology, combustion heat transfer characteristics of liquid fuels, optimal operation of the high-temperature air combustion, basic control in heating control, and steel piece heating control. Studies were performed for the heat treatment furnaces on the case of a direct firing furnace in evaluating the heat transfer characteristics, the case of a radiant tube furnace, application of thermal fluid simulation technology, furnace averaging technology, soot reducing technology, control technology, and trial design on a high-performance heat treatment furnace. (NEDO)

  11. Verification survey of geothermal exploration technology, etc. Report on the result of the developmental research on the development of the fracture type reservoir exploration method; Chinetsu tansa gijutsu nado kensho chosa. Danretsugata choryuso tansaho kaihatsu kenkyu kaihatsu seika sokatsu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of grasping fracture groups forming geothermal reservoirs with accuracy, the development of the fracture type reservoir exploration method has advanced the technical development of exploration methods of seismic wave use, electromagnetic induction use, and micro-earthquake use. This paper summarized main results of the development and problems to be solved in the future. In the development of the seismic wave use exploration method, the high accuracy reflection method using seismic wave, VSP and seismic tomography were adopted to the geothermal field, and technology effective for the exploration of fracture type reservoirs was developed. In the development of the electromagnetic induction use exploration method, the array CSMT method which can measure multiple stations along the traverse line at the same time was developed with the aim of grasping effectively and accurately fracture groups forming geothermal reservoirs as changes of resistivity in the shallow-deep underground. In the fracture group forming geothermal reservoirs, micro-earthquakes are generated by movement of thermal water and pressure variations. In the development of the micro-earthquake use exploration method, developed was the micro-earthquake data processing and analysis system (MEPAS). 179 refs., 117 figs., 28 tabs.

  12. FY 1999 achievement report on the development of high performance boilers. R and D on high performance industrial furnaces, etc.; 1999 nendo koseino boiler no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This project started in FY 1993 to survey the actual state of industrial use boilers. Based on the results of the survey, in fiscal 1995, 1996 and 1997, no improvement of the present technology which has limits, but the development was made of the oxygen combustion and element technology which are factors for heightening boiler performance with a new idea first in the world. In fiscal 1998, a target for the overall thermal efficiency of 105% was settled by testing a pilot plant where the element technology was integrated into the small once-through boiler, flue/smoke tube boiler, water tube boiler, etc. In fiscal 1999, the target of the overall thermal efficiency of boiler was reached by a pilot plant test to clarify combustion characteristics, heat transfer characteristics, environmental characteristics, etc. Further, effects of energy saving were increased by the adoption method of oxygen supply equipment. Concretely, an overall boiler efficiency of 105.73% exceeding the targeted value of 105% was achieved at a pilot plant of actual scale, by concentrating the results of each of the element technologies such as 'oxygen combustion,' 'condensation type flue gas heat exchanger,' 'high performance combustion control device,' and 'rapid rotating auxiliary machine.' (NEDO)

  13. Fiscal 2000 report on entrusted follow-up project for research cooperation on simplified industrial wastewater purification system; 2000 nendo sangyo haisui nado no kan'i joka system ni kansuru kenkyu kyoryoku follow up gyomu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The Research Cooperation Project on Simplified Industrial Wastewater Purification System carried out in cooperation with Indonesia and Malaysia was terminated in fiscal 1998. A follow-up check was conducted for spreading the fruits of the project. In concrete terms, for the study of problems to solve for the dissemination across Malaysia of the results of the project implemented in that country, technical guidance was provided relative to the study of operation performed by the counterpart operating their own pilot plant and the like. International Meeting for Technical Exchange was participated in, convened in Thailand in the period March 6-8, 2001. The contents of research activities included the two fields of (1) the selection of coagulants and (2) the study of pilot plant operation. In field (1), PAC (poly-aluminum chloride) and aluminum sulfate were compared with each other in terms of performance and cost in case they were used as coagulants, and then it was made clear that PAC was superior. In field (2), operation was studied using UASB (upflow anaerobic sludge blanket) type facilities of Southern Acid Plant. (NEDO)

  14. Survey report 1998. Survey on actual condition of science parks and similar facilities in Asian countries; 1998 nendo chosa hokokusho. Asia shokoku chiiki ni okeru science park nado no jittai chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Implemented at NEDO, on such technical development issues peculiar to developing nations as are difficult to solve by their research and development ability alone, has been a consistent research cooperation with countries in question, such as installation of plants and research facilities, joint research operation, and training of researchers, while Japanese technological skill and research and development know how are utilized, as the international cooperation projects. In this survey, an actual condition was investigated including potential of science parks and similar facilities in Asian countries (Thailand, Indonesia, Malaysia and India), for the purpose of unearthing the needs, seeds, etc., of the future international research cooperation projects. The parks and facilities selected for the survey are as follows. The Thai technology/science parks are the Thai Science Park and four other parks; the Indonesian technology parks are Bukit Indah Industrial City and eleven other parks; the major Malaysian technology parks are Technology Park Malaysia and fourteen other parks; the major Indian technology parks are Electronics City and fifteen other parks. (NEDO)

  15. Report on the project for spread/promotion of technology for the industrial waste optimized treatment in the Asian region; Asia chiiki sangyo haikibutsu tekiseika shori gijutsu nado fukyu sokushin jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The International Symposium `98 on the industrial waste problem in the Asian region was held in Tokyo on February 18, 1998. MITI commented on the present situation of the industrial waste problem in Japan and Japan`s environmental tackling toward the Asian region, and also Asian countries (China, the Philippines, Thailand and Korea) made reports. Japan reported on environmental preservation measures taken in the industrial circle, the industrial waste problem at companies which advanced into Asian countries, effects of the Basel Convention (which restricts border-crossing movement of harmful wastes) on recycle activities, Japan`s role in Asia, etc. In the panel discussion, discussions were made on human interchange in the informatization, recycling technology, shortage of personnel concerned with environmental protection, construction of a network in the Asian region and Japan` s role, etc. As to the treatment system for waste, the necessity was recognized of studying systems which meet with actual states of each country. It is also necessary to go on with discussing how the system should be for cooperation between governments and private companies. Importance of the recycle and information exchange was emphasized. 10 refs., 14 figs., 27 tabs.

  16. Report on the project for spread/promotion of technology for the industrial waste optimized treatment in the Asian region (International Symposium `98); Asia chiiki sangyo haikibutsu tekiseika shori gijutsu nado fukyu sokushin jigyo (symposium kaisai) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In Japan and Asian countries, the optimized treatment of industrial waste is the problem with the economic growth. Border-crossing movement of the waste for promotion of the renewable use is also a problem. Therefore, the International Symposium `98 on the industrial waste problem in the Asian region was held. China, Thailand, the Philippines and Korea were invited to Japan to give lectures. MITI of Japan reported on the present situation of Japan and the cooperation with Asian countries. The industrial circle reported on efforts for environmental protection measures to be taken, the industrial waste problem at companies which advanced into Asian countries, effects of the Basel Convention on recycling activities, Japan`s role in Asia, etc. In the panel discussion, promotion of cooperation for recycling technology and Japan`s support for formulating strategy on the industrial waste were requested to Japan, and the construction of an Asian area network was proposed. Concerning the cooperative system between governments and private companies, it was concluded that it was necessary to discuss it considering the actual state of each country. Importance of recycle and information exchange was realized again. 10 refs., 15 figs., 27 tabs.

  17. Fatores intrínsecos do custo energético da locomoção durante a natação Factores intrínsecos del desgaste energético de locomoción durante la natación Intrinsic factors of the locomotion energy cost during swimming

    Directory of Open Access Journals (Sweden)

    Fabrizio Caputo

    2006-12-01

    Full Text Available A quantidade de energia metabólica gasta em transportar a massa corporal de um sujeito por unidade de distância tem sido definida como custo energético da locomoção, ou especificamente para natação, o custo de nado. As diferenças no custo de nado entre os indivíduos parecem ser influenciadas por dois principais fatores, a resistência hidrodinâmica e habilidade técnica do nadador. O menor custo de nado apresentado pelas mulheres tem sido atribuído a menor resistência hidrodinâmica decorrente de menor tamanho corporal, maior percentagem de gordura e melhor posicionamento horizontal. Porém, essas diferenças no custo de nado entre homens e mulheres desaparecem quando corrigidos para o tamanho corporal. Em relação às crianças, o maior custo de nado comparado com o dos adultos quando corrigidos para o tamanho corporal pode ser explicado principalmente por menor habilidade técnica apresentada por elas. Para indivíduos com as mesmas características antropométricas, melhor habilidade técnica e maior tamanho da superfície de propulsão, associados a aumento na eficiência propulsiva, podem reduzir o custo de nado. Quando se comparam os diferentes estilos, o mais econômico é o crawl seguido pelo de costas em qualquer velocidade de nado. O borboleta é o estilo menos econômico a baixas velocidades (La cantidad de energía metabólica gastada en transportar la masa corporal de un individuo por unidad de distancia ha sido definida como el desgaste energético de locomoción, o específicamente para la natación, el desgaste de nado. Las diferencias en el desgaste de nado entre los individuos parecen ser influenciadas por dos principales factores, la resistencia hidrodinámica y la habilidad técnica del nadador. El menor desgaste de nado presentado por las mujeres ha sido atribuido a una menor resistencia hidrodinámica proveniente de un menor tamaño corporal, mayor porcentaje de grasa, y mejor posicionamiento horizontal. Sin

  18. FY 1999 report on the results of the superconductive energy application technology development/research on a total system, etc. Survey of potentiality of the commercialization of superconductive technology, effects of the introduction, etc. (Future course of the superconductive technology development in Japan); 1999 nendo chodendo denryoku oryokuyo gijutsu kaihatsu total system nado no kenkyu. Chodendo gijutsu no jitsuyoka kanosei oyobi donyu koka nado no chosa (Nippon ni okeru chodendo gijutsu kaihatsu no kongo no hokosei)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    By the use of superconductive technology, the following are aimed at: marked reduction in power loss of electrical equipment and power transmission path, and size/weight reduction in electrical devices by high current/magnetic flux density. The superconductive technology has advantages such as great energy saving effect, CO2 reduction and global environmental preservation. As an example, concerning the superconductive generator now being developed under the New Sunshine Project, power loss can be reduced by half, and by the use of high magnetic field, size/weight can be reduced such as reduction in rotor diameter and reduction in weight by half. Further, as an innovative system, cited are the superconducting magnetic energy storage system (SMES) and flywheel energy storage system. The superconducting magnetic levitation railway, medical use MRI, etc. have also innovativity which is difficult to get in the conventional technology. Effects are also expected of introducing the process development using superconducting magnet such as magnetic separation, electromagnetic metallurgy, electromagnetic agitation and monocrytal growth convection control. Also cited is Josephson electronic device. High performance SQUID in bio-magnetic/non-destructive inspection is also expected to be developed. (NEDO)

  19. FY 2000 report on the survey project on the policy for international energy utilization rationalization, etc. - model project on the heightening of international energy consumption efficiency. Viability survey of the project on energy conservation in the urea synthesis process in India; 2000 nendo kokusai energy shiyo gorika nado taisaku jigyo - kokusai energy shohi koritsuka nado model jigyo chosa hokokusho. Indo ni okeru nyoso gosei process sho energy jigyo jisshi kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of conserving energy and reducing greenhouse effect gas, a remodeling project was studied of urea plants constructed from the 1960s to the 1970s. Conditions for being companies for study are as follows: company has a production scale of more than 0.2 million t/y, adopts the complete circulation method, and will continue operation. And, Duncans Industries Ltd. (DIL) was selected. DIL owns the ammonia plant of 3 series x 400 t/d and the urea plant of 3 series x 682 t/d. In the modeling, stripper and carbamate condenser are added to the existing reactor as the main equipment. As a result of the study, the energy conservation effect was 13,667 toe/y, and the amount of reduction in greenhouse effect gas was 42,289 t-CO2/y. The total amount of this project was roughly estimated at 1.517 billion yen. By carrying out the project, the urea production cost is reduced approximately $9/t, but the project becomes unprofitable if the urea price is based on $188.1/t. (NEDO)

  20. Report on a survey in fiscal 1999. Supplementary survey on research and development of carbon dioxide fixation and effective utilization technologies utilizing bacteria and algae (the survey on feasibility of bio-technologies to create economic effects, such as the biological CO2 fixation technology); 1999 nendo saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu futai chosa. Keizaiteki koka wo soshutsusuru seibutsuteki CO{sub 2} koteigijutsu nado no biotechnology no kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Bio-technologies including the biological CO2 fixation technology, or the green bio-technologies (GBT) are the technologies indispensable in realizing the change to a resource circulating and environment harmonizing society that accompanies economical growth, or in other words, the 'sustainable development'. In quantifying the feasibility of these technologies, the GBTs that contribute to creating Japan's international competitive power and employment were specified, and an approach to establish the realization target in 2010 was adopted, upon identifying the general condition of the related markets inside and outside the country. The GBT is the technology that makes the best use of Japan's independent strength created by combining the enzyme engineering and fermentation engineering with the 'genome science' (HEART). The targets are to substitute four million kiloliters of petroleum with a resource circulation type energy generated by the bio-technology; apply the bio-technology to about 30% of products and processes produced or used in Japan's chemical industries; and aim at creating markets by using environmental measurement and analysis, treatment of hard-to-decompose substances, and supports on tree planting as the three pillars. A simulation on return on investment in GBT business suggests the effect of promoting PFI. (NEDO)

  1. Advanced research and development of gas hydrate resources. R and D of exploration and others - R and D of excavation technologies and others - surveys/researches on methods of evaluating environmental effects - surveys/researches on application systems; Gas hydrate shigenka gijutsu sendo kenkyu kaihatsu. Tansa nado ni kansuru kenkyu kaihatsu / kussaku gijutsu nado ni kansuru kenkyu kaihatsu / kankyo eikyo hyokaho no chosa kenkyu / riyo system ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Gas hydrate is a clathrate compound in a gaseous molecule as the host, stable under relatively mild environments. It is deposited in the 600m or deeper sea bottoms to form the gas hydrate deposit and massively occurring in the sea areas around Japan. This deposit has been studied viewed from natural gas resources, causes for natural hazards and contribution to the global warming. This project excavates a well in the deposit, to study possibilities of the technologies for decomposing, fluidizing and lifting the hydrate as the gas source, and for establishing the natural gas transporting/mooring systems in which its characteristics are utilized. The R and D activities are directed to the 4 areas, (1) development of the exploration technologies to determine the deposit sea area, quantity and conditions, (2) development of the stable well-excavation technologies, (3) studies on the effects of gas production on the environments, and development of the system for predicting the effects, (4) and studies on the application systems. The item (3) finds out the transportation/storage system possibly more economical than the current freezing/liquefaction technologies. The item (3) has the development themes of evaluating the geohazards caused by excavation and gas production, and their effects on the ecological systems. (NEDO)

  2. Report on a survey in fiscal 1999. Supplementary survey on research and development of carbon dioxide fixation and effective utilization technologies utilizing bacteria and algae (the survey on feasibility of bio-technologies to create economic effects, such as the biological CO2 fixation technology); 1999 nendo saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu futai chosa. Keizaiteki koka wo soshutsusuru seibutsuteki CO{sub 2} koteigijutsu nado no biotechnology no kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Bio-technologies including the biological CO2 fixation technology, or the green bio-technologies (GBT) are the technologies indispensable in realizing the change to a resource circulating and environment harmonizing society that accompanies economical growth, or in other words, the 'sustainable development'. In quantifying the feasibility of these technologies, the GBTs that contribute to creating Japan's international competitive power and employment were specified, and an approach to establish the realization target in 2010 was adopted, upon identifying the general condition of the related markets inside and outside the country. The GBT is the technology that makes the best use of Japan's independent strength created by combining the enzyme engineering and fermentation engineering with the 'genome science' (HEART). The targets are to substitute four million kiloliters of petroleum with a resource circulation type energy generated by the bio-technology; apply the bio-technology to about 30% of products and processes produced or used in Japan's chemical industries; and aim at creating markets by using environmental measurement and analysis, treatment of hard-to-decompose substances, and supports on tree planting as the three pillars. A simulation on return on investment in GBT business suggests the effect of promoting PFI. (NEDO)

  3. FY 2000 report on the results of the technology development of energy use reduction of machine tools, etc. Technology development of environmental load reduction related to water soluble lubricating oil, etc. (R and D of low energy coolant degradation prevention technology and waste liquid processing technology); 2000 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Suiyosei junkatsuyu ni kakawaru kankyo fuka teigen nado gijutsu kanri (tei energy coolant fuhai boshi gijutsu oyobi haieki shori gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The R and D were carried out on a system by which the long life of coolant of machine tools can be achieved and a system to process waste efficiently, economically and with less environmental loads, and the FY 2000 results were summed up. In the R and D of a system to prevent degradation of low energy coolant, measurement was made of effects of the degradation prevention system at a laboratory level, and it was found out that propagation of bacteria causing the degradation can be prevented with pH kept high. Further, it was admitted that the alkali effect on metal formability was not very much. As to the coolant processing, in the present situation, most of the coolant is taken back by industrial waste processing dealers. So, the development of the low energy waste liquid processing system is earnestly desired. In the R and D of the low energy waste liquid processing system, test on characteristics evaluation was conducted about each method of systems. Subjects to be improved/solved were extracted such as the point that volatile organic matters are included in condensed water after evaporation of waste liquid and there seems to be a possibility of needing the secondary processing. (NEDO)

  4. Report on the achievements in fiscal 1999. Technology to use gas hydrate as a resource (Research and development for exploration, research and development on drilling technologies, investigative research on an environment influence evaluation method, and investigative research on a utilization system); 1999 nendo gas hydrate shigenka gijutsu sendo kenkyu kaihatsu seika hokokusho. Tansa nado ni kansuru kenkyu kaihatsu, kussaku gijutsu nado ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no chosa kenkyu, riyo system ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The contents of the research and development performed in the current fiscal year are as follows: (1) research and development for exploration, (2) research and development on drilling technologies, (3) investigative research on an environment influence evaluation method, and (4) investigative research on a utilization system. In Item (1), element analysis data are used to study a method to estimate production environment of hydrate ore beds by using an inorganic ion analyzer and a trace amount element analyzer, the crust thermal flow measuring method is used to discuss a method to analyze the hydrate stability zones together with the data of sea area exploration records, and conceptual design is made on a resource potential evaluation system. In Item (2), experiments and analytical discussions are performed on decomposition control of the gas hydrate solid-liquid interface according to such conditions for the drilling fluid as temperatures and flow rates. Elucidation is given on the initial process of bubble generation for behavior of decomposed gas bubbles. Observation and elucidation are made on two-phase flow behavior of non-Newtonian fluid. In Item (3), conceptual design is carried out on a system to detect elements of shape change in each bed due to fluid movement in a gas hydrate bed and an upper bed. In Item (4), discussions are given on the optimizing conditions for generation and dissociation of gas hydrates. Investigation is made also on a possibility of the transportation and storage system. (NEDO)

  5. Report on survey for possibility of applying bio-technologies to biomass in fiscal 1999. Aiming at developing a kitchen refuse and waste water treatment and energy production system that can be installed as an ancillary facility of buildings; 1999 nendo biomass eno bio technology oyo kanosei chosa hokokusho. Biru nado no futai setsubi to shite secchi kanona, chukai, haisui nado no shori narabi ni energy seisan system no kaihatsu wo mezashite

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes the survey and discussion on a system to treat microorganisms generated from organic wastes and recover bio-gas energy as an ancillary facility of buildings. The roof of a building is the most suitable location in terms of open space and odor problem, and because the waste liquid after energy recovery can be flown into the city sewage system. Suitable processes for energy recovery are the primary fermentation, followed further by second stage fermentation purposed of reducing BOD. Since rapid enhancement of the efficiency cannot be expected from the present methane fermentation technologies, it is worth discussing to convert the first step from methane fermentation to hydrogen fermentation, for which technological development is indispensable. Permission by the national or local government would be an important condition. Organic wastes treatment systems with different scales may be considered from wastes treatment in each house to treatment of wastes after collection on the whole city basis. Treating wastes with high water content, such as kitchen refuses and human waste is beneficial among organic wastes being collected and treated by local governments. It is beneficial because sorted collection for that purpose can be carried out, and existing incineration systems can be operated more efficiently. (NEDO)

  6. Fiscal 1998 R and D project on global environmental industrial technology. Research result report on DNA analysis and information processing technology for photosynthesis microorganisms (Development of CO{sub 2} fixation and effective use technology by using bacteria and algae); 1998 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo. Kogosei biseibutsu nado DNA kaiseki joho shori gijutsu no kenkyu (saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report summarizes the fiscal 1998 research result on DNA analysis and information processing technology for photosynthesis microorganisms. On the study on DNA analysis technology by triple-strand formation method, as the comparison study result of a READ method, stable triple- strand formation method and hairpin method, a READ method showed the highest triple-strand formation efficiency for target DNA. On the study on accurate separation technology of specific genes, establishment of protocols was promoted for solid-phase probe technology, subtract technology and leveling technology. On the study on DNA microarray analysis technology by high-efficiency hybridization method, the analysis technology of genes by hybridization method using DNA chips is under investigation. In addition, the high- efficiency analysis technology of specific DNA segments by using an affinity sensor, and the high-accuracy cloning technology for DNA with altered primary structure were also studied. (NEDO)

  7. Fiscal 1997 survey report / R and D of important region technology. R and D of technologies giving multi-functional characteristics to C/C composites (development of high-grade surface processing technology for engine members for methane fueled air craft. 1. control technology of micro structures of ultra-high temperature members); 1997 nendo seika hokokusho juyo chiiki gijutsu kenkyu kaihatsu. Fukugo kino buzai kozo seigyo gijutsu no kenkyu kaihatsu (methane nenryo kokukiyo engine buzai no kodo hyomen kako gijutsu kaihatsu). 1. chokoon buzai micro kozo seigyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of developing members most suitable for aircraft use engines with methane as fuel, the R and D were conducted of technology to reform surfaces and interfaces of materials. In the R and D, the paper took up carbon fiber reinforced carbon composite materials (C/C composites). In the surface control and reformation technology using the ion engineering method, etc., in the sealing processing of C/C composites, tried was the formation of a C/SiC/Si3N4 composite layer which was formed by Si3N4 much smaller in thermal expansion coefficient than SiC. Further, technologies on ion injection, thin film formation, giving of oxidation resistance/corrosion resistance, improving/giving of thermal shock resistance, etc. In the multi-functional coating formation technology such as high liability and corrosion resistance, the study was carried out of the dense composite functionally-gradient layer as thermal stress relaxation layer and the fiber reinforced layer by carbon fiber using pores. Besides, studies were made of technologies of the micro structure control combination, evaluation of ultra-high temperature resistant environmental characteristics, etc. 61 refs., 198 figs., 44 tabs.

  8. Buoyancy and similarity of the swimming of Manta birostris(Elasmobranchii: Myliobatidae) with the flying cycle of Columba livia(Aves: Columbidae)

    OpenAIRE

    Meza Vélez, Iván

    2013-01-01

    Se analizó la física de la flotación en la mantarraya Manta birostrisy se comparó el nado con el ciclo de vuelo de la paloma doméstica Columba livia, con la finalidad de encontrar similitudes y diferencias en las locomociones y las leyes físicas que intervienen. Se demostró que uno de los dos ciclos de nado estudiados de esta especie posee tres de las cuatro fases principales del ciclo de vuelo de la paloma doméstica. También se demostró un “efecto paracaídas” en M. birostris, el cual le ...

  9. Políticas do presente em Carlos Ríos e César Aira

    Directory of Open Access Journals (Sweden)

    Antonio Carlos Santos

    2013-06-01

    Full Text Available Em Manigua, Pripyat e A la sombra de Chaki Chan, Carlos Ríos nos mostra uma face da con­temporaneidade: três territó­rios na mar­gem do Império, um aban­do­nado depois de um aci­dente na Usina Nuclear de Chernobil e habitado por seres con­tami­nados pela radia­ção, outro dispu­tado por etnias em vias de desapareci­mento e um terceiro disputado por gru­pos de catadores de alumínio. São relatos que se fazem com fragmentos catados na Internet, nomes, listas de palavras, peda­ços de histórias reutilizados em uma literatura que se faz com os restos de modos de vida que resis­tem em meio ao caos da guerra permanente.

  10. Interferência dos ácidos graxos ômega-3 nos lipídeos sangüíneos de ratos submetidos ao exercício de natação Omega-3 fatty acids interference on the blood lipids of rats subjected to swimming exercise

    Directory of Open Access Journals (Sweden)

    Bettina Moritz

    2008-12-01

    Full Text Available OBJETIVO: Investigar os efeitos da suplementação com ácidos graxos ômega-3, nas doses de 0,5 e 1,0g/kg/dia, nos lipídeos sangüíneos de ratos submetidos ou não ao protocolo do nado. MÉTODOS: Ratos Wistar foram divididos em grupos: controle, controle+nado, ácidos graxos ômega-3 e ácidos graxos ômega-3+nado. Os ácidos graxos ômega-3 e ácidos graxos ômega-3+nado receberam suplementação; os demais receberam água por gavagem. Os controle+nado e ácidos graxos ômega-3+nado foram submetidos ao exercício. Foram avaliadas as concentrações plasmáticas de colesterol total, triglicérides e lipoproteína de alta densidade, antes e após os procedimentos experimentais. RESULTADOS: No protocolo de 0,5g/kg/dia, em relação às concentrações de colesterol total, foi observada redução significativa proporcionalmente maior no grupo ácidos graxos ômega-3+nado, apesar de o grupo controle+nado e o ácidos graxos ômega-3 também terem apresentado diminuição. No ensaio de 1,0g/kg/dia todos os grupos apresentaram uma diminuição que foi maior, respectivamente, no ácidos graxos ômega-3+nado e, a seguir, no ácidos graxos ômega-3. Quanto aos triglicérides, foram encontradas reduções em todos os grupos experimentais, que foi maior no grupo ácidos graxos ômega-3+nado, do protocolo de 0,5g/kg/dia, enquanto que no de 1,0g/kg/dia a diminuição foi significativa apenas nos grupos ácidos graxos ômega-3 e ácidos graxos ômega-3+nado. Quanto ao HDL, no protocolo de 0,5g/kg/dia foi encontrado aumento nos animais que não foram suplementados, enquanto que em todos os grupos de 1,0g/kg/dia houve uma diminuição do HDL. CONCLUSÃO: A suplementação com ácidos graxos ômega-3 nas doses 0,5 ou 1,0g/kg/dia, associada ao nado, reduzem as concentrações plasmáticas de colesterol total e triglcérides, mas estudos adicionais, também com outras doses, são necessários para a compreensão da relação entre a ingestão de óleo de peixe e

  11. FY 1999 report on the results of the technology development of super metal. Development of technology of high corrosion resistant iron-base fine structure controlling metal materials; 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Kotaishokusei tetsukei bisai kozo seigyo kinzoku zairyo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of developing iron/steel materials which enable remarkable improvement of maintenance loads and longevity of oil field developmental materials, study was conducted for remarkable improvement of strength and corrosion resistance by making crystal grain of iron/steel materials micro-fine to the limit, and the FY 1999 results were summed up. The study was conducted on the technology of fine structure formation using strong magnetic field and technology to predict material quality of micro structure using computational science. As a result, it was found that the fine grain even in size can be obtained by a combination of magnetic field orientation and recrystallization. By this, an image was constructed of the industrialization process of fine grained steel production which was combined with warm rolling process and applied strong magnetic field. Using the method to homogenize the finite element method, the basement was established for the method to evaluate an effect of the second phase on mechanical characteristics of fine multi-phase structure steel. The cementite single-phase film which is an important structural phase of carbon steel was successfully formed, and the Young's modulus and Poison ratio were determined as basic data for material design. (NEDO)

  12. Report on achievements in fiscal 1999 on the project for development of an energy use rationalizing technology. Development of a basic technology to design and fabricate an innovative light-weight structure; 1999 nendo kakushinteki keiryo kozo sekkei seizo kiban gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes the achievements in fiscal 1999 on development of a basic technology to design and fabricate an innovative light-weight structure. Taking CFRP and aluminum alloy having excellent specific strength as the main object materials, weight reduction and reliability enhancement in aircraft structure are intended, while reducing largely the number of parts. In particular, the wings, the nose and the leading edge construction of civilian aircraft are of the structure assembled with a large number of parts, and are suitable as the research objects. A new conception will be introduced that structural members are fabricated by utilizing the characteristics of integrally formed CFRP, which will be assembled into a whole structure. Large structural metallic members currently used have such drawbacks as the use of great number of parts, complexity in manufacturing processes, low reliability, weight increase and corrosion due to rivet jointing. In order to solve these problems, development will be made on technologies for thin-wall large-size precision casting, and high-accuracy high-quality welding. To combine different kinds of members, and optimize strength, weight and economic performance of the entire structure, high-efficiency integration technologies will be discussed, and prototype full-size structure will be fabricated. The current fiscal year has started up the technology committee and its operation, analyzed technological problems in the entire structure, and established the action programs. An investigation was performed on the technological trends in overseas countries. (NEDO)

  13. Fiscal 1998 achievement report on regional consortium research and development project. Venture business fostering regional consortium in its 2nd year--Creation of key industries (Development of processing of new structure-designed high-performance polymer alloy); 1998 nendo shinkina kozo seigyo koseino kobunshi alloy no seikei kako ni kansuru kenkyu kaihatsu seika hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Efforts are exerted to make novel recyclable polymer alloys excellent in material characteristic and to develop a technology for processing them, for which liquid crystalline polymers equipped with a self-alignment capability are combined with thermoplastic resins. In the research on the alloying of polyethylene terephthalate (PET) and liquid crystal polymers (LCP), studies are conducted about inorganic nucleating additives, thermostabilizers, and mold releasing lubricants, and a success is attained in the manufacture of excellent alloyed pellets. In the injection molding of alloys of PET and LCP, a product is obtained, among those produced with the rate of LCP varied, which behaves excellently even at a high resin temperature of 285 degrees C. It is found about PET/LCP alloys that improvement is achieved with additional LCP in terms of the warpage temperature under load, bending property, strength, and dimensional stability upon exposure to heat. In the study of the response of LCP-diffused PET to a process demanding distortion, an injection-molded product containing 10-20% of LCP is found to exhibit excellent ductility. It is also found that PET/LCP alloys may be cut and machined easily and that therefore their crushing for the recycling purpose will be easy. (NEDO)

  14. Sensing of subsurface faults based on an imaging technique for teleseismic waveform data. 2. Feasibility study for application to oblique incidence, multi-event and noise data; Enchi jishin hakei data wo mochiita chika kozo imaging ni yoru chichu danso kenshutsu no kokoromi. 2. Naname nyusha, multi event, noise wo fukumu hakei eno tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Murakoshi, T; Takenaka, H; Saita, T [Kyushu University, Fukuoka (Japan). Faculty of Science; Suetsugu, D [Building Research Institute, Tokyo (Japan); Furumura, T [Hokkaido University of Education, Sapporo (Japan)

    1996-05-01

    An examination was made on the method in which imaging of subsurface was carried out with teleseismic waveform data for sensing of faults. In the examination, an experiment was done on the sensing of faults with higher precision, by applying oblique incidence as well as perpendicular upward incidence of SH plane waves, and thereby stacking the imaging in plural events. In numerical experiments, 28 observation points were arranged at 500m spaces apart on the surface, and the incident waves were made the SH plane waves having a bell-shaped time function, with incidence made at an angle varied as 0{degree}, +15{degree} and -15{degree} from the lowest layer of a model. In the calculation of the wave motion field, a difference calculus with secondary accuracy was used for both time and space. In addition, data was prepared with a random noise added to a synthesized waveform to be used as observation data. The calculated waveform data were likened to the observation waveform, to which the method for imaging faults was applied. Consequently, it was noted that satisfactory results were obtained compared with the case where faults were sensed by one event alone. 5 refs., 4 figs.

  15. Project for surveying improvement in energy demand and supply structure (comprehensive survey on improvement in energy demand and supply). FY1998 report on achievements of Technical survey on pyroelectric power generation systems; Energy jukyu kozo kodoka chosa jigyo (energy jukyu kodoka sogo chosa). Shoden hatsuden system no gijutsu chosa 1998 nendo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    This paper reports the achievements on research of pyroelectric power generation systems in fiscal 1998. In the research, a small continuous pyroelectric conversion equipment was fabricated and experimented. The experiment using an aluminum foil electrode revealed that the foil melts during discharge opening holes, thus making it impossible to increase net conversion efficiency. The net conversion efficiency was derived in an experiment using foil evaporated with indium instead of the aluminum foil. Indium has inferior electric conductivity to aluminum, but is melting point is as low as 145.6 degrees C. Therefore, if a pyroelectric film had electric fatigue due to use over an extended period of time, indium may be melted to make recovering and reusing pyroelectric copolymer possible. Thus, the indium electrode was found suitable for pyroelectric conversion. Analysis of the experimental data indicated that the final possible net output can be 7.6 W/m{sup 2} if each operation variable considered possible in the future is superimposed on the pyroelectric film. This survey revealed that low-temperature waste heat can be converted to high voltage continually by using the pyroelectric conversion equipment at CANMET Energy Technology Centre. (NEDO)

  16. Fiscal 1999 achievement report on research and development of industrial technology of new industry creation type. Research and development of intelligent material and structural system (Development of energy use rationalization technology); 1999 nendo chiteki zairyo kozo system no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Fiber or foil shaped sensor materials and actuator devices were integrated with composite materials and composite material structures for processing and controlling information, and then studies were conducted about materials and structural systems for enabling real-time detection of damage in materials and structures, examination of soundness, control of noise and vibration, and the like. Concerning optical fiber sensors in the development of smart manufacturing technologies, the impact imposed on composite materials by sensors embedded therein was investigated, and the scope of their applicability was determined. In the development of actuator materials and devices, ceramic actuators were fabricated by microwave sintering, and it was found that they were higher in performance by 30% than actuators of the conventional design. In the testing of demonstrators, molded body monitor basic tests using optical fiber sensors were conducted for jet engine static vane models, and temperature dependence of optical intensity was understood. (NEDO)

  17. Basic studies on design supporting system of offshore structure. Part 2. Implementation of structural design supporting system of offshore structures; Kaiyo kozobutsu wo taisho to shita sekkei shien system ni kansuru kisoteki kenkyu. 2. Kaiyo kozobutsu no kozo sekkei shien system no kochiku

    Energy Technology Data Exchange (ETDEWEB)

    Nomoto, T.; Hamada, K.; Aoyama, K. [The University of Tokyo, Tokyo (Japan)

    1996-12-31

    In order to improve the existing design-supporting system for offshore structures, new functions are added to evaluate information of the products, especially those for structural designs. The structural analysis system should be provided with a function of design modification, to efficiently support the structural analysis of these structures. The new system adds hierarchy of various offshore structure models and three-dimensional dimensions to clarify structural and geometrical constraints and design-modification function. The design-modification function is included by use of the hierarchy. The other new functions are finite element analysis systems for the main structure and components, and rigidity calculation for the main structure. The main structure and functional element models are confirmed to be useful also for utilization of information, and provide necessary information of the product models. 11 refs., 11 figs.

  18. FY 1999 research and development of technologies for creating original high-function materials. Development of technologies for functionalized materials for power generating facilities (Report on the R and D results of controlling precise structures of polycondesed systems); 1999 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo koseinoka zairyo gijutsu kaihatsu (shukugokei seimitsu kozo seigyo no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The research and development project is implemented for the polymerization catalysts and precise polymerization processes which can freely control the primary structures, e.g., molecular weight, regularity, branching and terminal group structures, of the polymers produced by polycondensation and ring-opening polymerization, in order to drastically improve their functions, and the FY 1999 results are reported. The basic studies on the precise polycondensation successfully lead to chemoselective synthesis of polymers by the direct polymerization, and synthesis of polyamides of narrow molecular weight distribution and high-molecular-weight aliphatic polyesters. The other items studied include precisely, regularly sequential polymerization by amine activation, innovative synthesis of polycarbonate, precise control of branching structures, regioselective oxidative coupling polymerization, and matrix polycondensation. The basic studies on the controlled ring-opening polymerization cover cationic ring-opening polymerization behavior of 6-membered thiocarbonate derivative having an ester group, to generalize the polymerization controlled by neighboring group participation. The other items studied include precise control of branching structures, molecular weights, network polymer structures, and polymer unit sequences. (NEDO)

  19. Research report of FY 1997 on the industrial science and technology development. Technology development of super-metal (technology development of nano-amorphous structural control materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (nano-amorphous kozo seigyo zairyo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research and development of the innovative metals have been conducted, by which the weight reduction of members can be done by drastically improving the strength compared with conventional metals. For the high-rate cluster deposition and super plastic forming technologies, research and development of aluminum-based light-weight materials have been conducted, which provides excellent strength, toughness, and super plastic formability at room temperature. For the high-density energy utilization and control technology (amorphous-A), super-metals have been investigated as high dew point and corrosion resistance materials used for waste incinerators operated under the very severe conditions. These are expected to be applied to the apparatuses and equipment due to their excellent properties. For the controlled cooling technology (amorphous-B), super-metals with excellent soft magnetic characteristics and degree of shape freedom have been investigated for high performance and high efficiency devices including electric/electronic/communication devices, power transmission devices, and various industrial devices and parts. These are expected to contribute to the creation of new markets and the improvement of international competitive force. 123 refs., 160 figs., 33 tabs.

  20. Report on results concerning development of supermetal technology, R and D of offshore oil production supporting system, and development of technology for aluminum-based high-anticorrosive microstructured metallic material (FY2000); Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Kaitei sekiyu seisan shien system kenkyu kaihatsu (Aluminium kei kotaishokusei bisai kozo seigyo kinzoku zairyo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of developing high strength and high-anticorrosive aluminum-based material through microstructure control, R and D was conducted, with fiscal 2000 results compiled. In the research of grain refinement mechanism, molten metal rolled stock was experimentally produced in which Mg content was varied 0-2.5 mass % with Al-2.5 mass % Mn as its base. As a result, a microstructure with an average grain size of about 3 {mu}m was obtained by processing the alloy through homogenization at 550 degrees C, cold rolling by 91% and the final treatment at 350 degrees C without Mg addition. Addition of Mg increased square grain boundaries in the microstructure, raising proof stress to about 180 MPa in Al-2.5%Mn-2.5%Mg alloy. In the research of development of the machining process, a rapid heating process was performed on a typical aluminum alloy, with the effect examined, by an alloy system or a plate thickness, on the electric power used and on the temperature reached. A rapidly heated aluminum alloy plate turned to have a microstructure with equi-axed grains of a uniform size, compared with a salt bath processed material heated at the same temperature. (NEDO)

  1. Acoustic excitation of diffusion flames with coherent structure in a plane shear layer. ; Application of active combustion control to two-dimensional phase-locked arranging measurements. Soshiki kozo wo tomonau heimen sendai kakusan kaen no onkyo reiki. ; Nijigen iso heikin bunpu sokutei eno active nensho seigyo no oyo

    Energy Technology Data Exchange (ETDEWEB)

    Ishino, Y.; Kojima, T.; Oiwa, N.; Yamaguchi, S. (Nagoya Institute of Technology, Nagoya (Japan))

    1993-11-25

    The acoustic excitation of a plane diffusion flame enhances the periodicity of organized eddy controlled combustion. In this study, to clarify an effectiveness of application of active combustion control, phase characteristics of the excited eddy flames with high periodicity have been examined. A computer-aided phase-locked averaging method was employed to obtain graphical two-dimensional contour maps of the instantaneous profiles of temperature and CH emission. Both maps consisting of eight consecutive phases indicated clearly not only the periodic behavior of the organized eddy flame, but also the gas dynamic properties peculiar to those flames with coherent structure. In addition, the profiles of local contribution of the sound field to the combustion process were examined by calculating the two-dimensional distribution of the local Rayleigh index. Calculation results of the two-dimensional distribution of the local Rayleigh index indicated that the organized eddy flames have high sensitivity to sound, and play an important role in an interaction of sound and flame. 6 refs., 9 figs.

  2. FY 1999 report on the results of the technology development of super metal (R and D of the undersea oil production support system). Development of technology of aluminum-base high corrosion resistant fine structure controlling metal materials; 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Kaitei sekiyu seisan shien system kenkyu kaihatsu (aluminium kei kotaishokusei bisai kozo seigyo kinzoku zairyo gijutsu kaihtsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of developing aluminum materials excellent in industrial characteristics, a study was conducted to create large-sized aluminum materials having mesoscopic crystal structure, and the FY 1999 results were summarized. In this fiscal year, to create the fine crystal grain structure, the following were conducted: fundamental study of high strain accumulation process, study of a mechanism of fine crystal grain formation, development of the processing method, and development of evaluation technology. In the study of high strain accumulation process, effects were examined of conditions of molten metal rolling on castability. Fundamental studies were also made of innovative technologies such as ECAP method, pre-forged structure controlling rolling, accumulative roll bonding and thermomechanical treatment. In the study of the mechanism of fine crystal grain structure formation, the following were conducted: Al-Mn base alloys produced by molten metal rolling, 6061 alloys by warm rolling with different peripheral speed rolling, and 7000 group alloys by warm rolling. As to the processing method, study was made on low-temperature rolling technology and rapid heat treatment technology. As to the evaluation technology, study was made on evaluation of crystal grain diameter by EBSP. (NEDO)

  3. Fiscal 1998 research report. Industrial science and technology research project / R and D on creative advanced functional materials (structure-controlled materials) / Harmonized molecular materials; 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) seika hokokusho. Bunshi kyocho zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    R and D on harmonized molecular materials aim at establishment of the technology fabricating self-assembled organic molecular films on solid surfaces which have potentials of mechanical response to electric fields, electroluminescence or optical functions. Molecule harmonization expresses new structures and functions difficult to be expressed by each molecule alone, by cooperative interaction between molecules due to noncovalent bond. Functional thin films were developed by controlling alignment and/or arrangement of molecules with an aid of self-assembling processes. Thiol compounds with larger dielectric anisotropy were synthesized as electric field responsive self-assembled films. {pi}-conjugated compounds composed of phenyl-capped oligothiophenes were synthesized as electroluminescent self-assembled films, and their high crystallinity and efficient electroluminescence were found. Heat- and solvent-resistant lyotropic liquid crystalline (LLC) aligning polymers such as polyamine and polyimine were synthesized as new optically functional LLC dye self-assembled films. (NEDO)

  4. Developments of DPF systems with mesh laminated structures. Performances of DPF systems which consist of the metal-mesh laminated filter combustion with the alumina-fiber mesh, and the combustion device of trapped diesel particles; Mesh taso kozo no DPF no kaihatsu. Kinzokusen to arumina sen`i mesh ni yoru fukugo filter to filter heiyo heater ni yoru DPF no seino

    Energy Technology Data Exchange (ETDEWEB)

    Kojima, T; Tange, A; Matsuda, K [NHK Spring Co. Ltd., Yokohama (Japan)

    1997-10-01

    For the purpose of continuous run without any maintenance, new DPF (diesel particulate filter)systems laminated by both metal-wire mesh and alumina-fiber mesh alternately, are under the developments. The perfect combustion of trapped diesel particulate can be achieved by a couple of the resistance heating devices inserted into the filter. 5 refs., 7 figs., 3 tabs.

  5. Fiscal 1998 R and D on original advanced material creation technology (development of precise structure control materials for oil refinery improvement). R and D result report on multi-dimensional polymers; 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (sekiyu seisei kodoka seimitsu kozo seigyo zairyo kaihatsu) seika hokokusho. Tajigen kukan polymer no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For development of radical-controlled synthesis technology of aromatic compounds using enzyme-related catalysts and synthesis technology of ordered compounds, and development of synthesis technology of new polymer groups with non-covalent bond linkages and new topological structures, this R and D on multi-dimensional polymers is promoting 2 research themes, (1) precise polymer synthesis technology using enzyme-related catalysts, and (2) chemical synthesis technology for polymers with non-covalent bond linkages and new topological structures. The joint research on (1) precise polymer synthesis technology using enzyme-related catalysts established the high-yield synthesis technology of phenol dimer first in the world. The joint research first studied the synthesis using 2,6-dimethylphenol as monomer through synthesis of phenol groups using ferrosalen, and obtained the mixture of polymer components more than 10,000 in molecular weight and low-molecular weight components by using 1,4- dioxane as solvent. (NEDO)

  6. Structure and coke preventing characteristics of Ca-Ni-Mo/Al sub 2 O sub 3 catalyst for hydrogenation of brown coal liquid bottoms. Kattan ekikaabura suisokayo Ca-Ni-Mo/Al sub 2 O sub 3 shokubai no kozo to tansoshitsu seisei yokusei sayo

    Energy Technology Data Exchange (ETDEWEB)

    Kimura, T. (Cosmo Oil Co. Ltd., Tokyo (Japan)); Kaneko, T.; Kageyama, Y. (Mitsubishi Kasei Corp., Tokyo (Japan). Research Center); Kawai, S. (Nippon Brown Coal Liquefaction Co. Ltd., Tokyo (Japan))

    1990-09-01

    Operating a 50 t/d fixed bed pilot plant, hydroprocessing of de-ashed coal liquid bottoms (DAO) derived from Victorial Brown coal liquefaction has been carried out in Australia using a newly developed Ca-Ni-Mo/Al {sub 2} O {sub 3} catalyst. This catalyst has a great advantage compared with conventional molybdenum catalysts in that there is less coke formation using this catalyst as indicated by 5,000 h runs in a 0.1 t/d bench scale plant. In this paper, the catalyst active center and the role of Ca in the Ca-Ni-Mo/Al {sub 2} O {sub 3} catalyst were analyzed using Raman, TPS-XPS, EXAFS and AES methods. Molybdenum is loaded as CaMoO {sub 4} and X-ray diffraction data. But the oxide is changed to MoS {sub 2} after sulfiding treatment. Data of the Mo-S bond obtained from EXAFS analysis indicated that MoS {sub 2} has a tendency to pile up on the Ca-Ni-Mo/Al {sub 2} O {sub 3} catalyst. 20 refs., 12 figs., 5 tabs.

  7. Report on results concerning development of supermetal technology (FY2000). Development of technology for high-anticorrosive iron-based microstructured metallic material; Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Kotaishokusei tetsukei bisai kozo seigyo kinzoku zairyo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of greatly improving strength and corrosion-resistance through ultra-refinement of crystal grains of steel materials, research was conducted on microstructure refinement technology utilizing strong magnetic fields and on mechanical property estimation technology for ultra-refined structure steel using computational science, with fiscal 2000 results compiled. In the research for grain refinement utilizing magnetic fields, an inline experiment of transformation was carried out and, as a result, equi-axed grains of 1.6 {mu}m were attained on a 3 mm thick steel plate of commercially used composition by a method of recrystallization after cold rolling. The experiment revealed that the 1 {mu}m grains could be obtained by setting cold-rolling work load to 80%. In addition, data were acquired relating to conditions such as steel composition affecting the formation of orientation in structures, work load and rolling temperature for areas to be recrystallized, holding temperature and time in the magnetic field, and intensity of the magnetic field. In the research for estimating mechanical properties of microstructures by computational science, a Monte Carlo simulation was carried out by employing the result of a polycrystal plasticity method program as the initial value, with a prototype established of the integrated simulation method from the deformation to the microstructure formation. (NEDO)

  8. Basic studies on design supporting system of offshore structure. Part 2. Implementation of structural design supporting system of offshore structures; Kaiyo kozobutsu wo taisho to shita sekkei shien system ni kansuru kisoteki kenkyu. 2. Kaiyo kozobutsu no kozo sekkei shien system no kochiku

    Energy Technology Data Exchange (ETDEWEB)

    Nomoto, T; Hamada, K; Aoyama, K [The University of Tokyo, Tokyo (Japan)

    1997-12-31

    In order to improve the existing design-supporting system for offshore structures, new functions are added to evaluate information of the products, especially those for structural designs. The structural analysis system should be provided with a function of design modification, to efficiently support the structural analysis of these structures. The new system adds hierarchy of various offshore structure models and three-dimensional dimensions to clarify structural and geometrical constraints and design-modification function. The design-modification function is included by use of the hierarchy. The other new functions are finite element analysis systems for the main structure and components, and rigidity calculation for the main structure. The main structure and functional element models are confirmed to be useful also for utilization of information, and provide necessary information of the product models. 11 refs., 11 figs.

  9. FY 2000 report on the results of the research and development project for new industry creation type industrial science technologies. R and D of the intellectual material and structural systems (Development of technologies for rational use of energy); 2000 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki zairyo kozo system no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 2000 results of the R and D project for development of intellectual materials and structural systems, as part of development of technologies for rational use of energy. The program for development of health monitoring technologies produces the bright prospects for commercialization of the fine FBG (Fiber Bragg Grating) sensor which can be embedded in a CFRP prepreg, and establishes the crack detecting method. The program for development of smart manufacturing technologies describes the dielectric constant sensor capable of monitoring the curing process, detection of the cured conditions by the optical fiber sensor, and development of the performs by RTM (Resin Transfer Molding). The program for technological development of the active-adaptive structures conducts the vibration- and noise-controlling tests for the small-size structural elements, confirming that the damping coefficient is improved by at least 20% and acoustic power is reduced by at least 30%. The program for developing the actuator materials and elements improves the piezoelectric characteristics of the PZT-based materials by hybrid sintering, and develops the actuators of high-durability FGM (Function-Gradient Materials). It also develops the foil- and belt-shaped shape memory alloys by arc-aided dissolution and rapid solidification of Ti-Ni-Cu-based alloys. (NEDO)

  10. Fiscal 1998 research report on the R and D on industrial science and technology for creating new industries. R and D on intelligent material and structure systems (Development of practical technology for rational use of energy); 1998 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki zairyo kozo system no kenkyu kaihatsu (energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    As a part of development of intelligent material/structure systems, study was made on practical technology for rational use of energy. For resource saving and energy saving (smartening) for large and complex machines and structure systems, light-weight long-life materials/structures are indispensable. Study was thus made on the basic technology of material/structure systems equipped with realtime defect detection function, structural integrity diagnosis function and control function of noise and vibration through information processing and control by integrating composite material/structure and fiber or film sensor material/device. For development of smartening technology, sensing technology was studied to detect the interior structure of composite material/structure compacts. The basic fabrication technology of ceramic actuator materials/devices, and shape memory alloy system actuators were put into development. Smooth connection and cooperation among groups were promoted through the technical committee and research on domestic and overseas trends for forming common knowledge. (NEDO)

  11. Correlation between interstitial flow and pore structure in packed bed. 1st Report. Axial velocity measurement using MRI and visualization of axial channel flow; Juten sonai ryudo to kugeki kozo no sokan. 1. MRI ni yoru jikuhoko ryusoku bunpu no keisoku to jikiuhoko channel ryu no kashika

    Energy Technology Data Exchange (ETDEWEB)

    Ogawa, K; Yokouchi, Y; Hirai, S [Tokyo Institute of Technology, Tokyo (Japan)

    2000-02-25

    Structure and velocity measurements using magnetic resonance imaging (MRI) have been performed experimentally to obtain a correlation between pore structure and interstitial flow through the packed bed of 5 mm diameter in the tube of 36 mm ID. To measure axial velocity maps of water flow through the packed bed, the phase method of using the phase difference of water spin magnetization between flowing and stagnant fluids by applying magnetic fields with bipolar gradients was employed. The spatial resolution of the obtained map in 0.2 mm x 0.2 mm x 0.5 mm. It was made clear from the obtained axial velocity maps that channel flows with higher axial velocity were induced not only near the wall but also in the internal region of the packed bed. Furthermore, pore structure of the packed bed was characterized from multi-slice images by partitioning of void space and combining of each pore section along the axial direction to analyze the structure-flow correlation. It was found from image analysis that axial channels with long and straight void space existed in the pore structure, and that most of the channel flows with higher axial velocity were induced in the axial channels. The flow rate through an axial channel depends on the square of the averaged cross section of the axial channel. (author)

  12. Research report on promotion of geothermal energy exploitation for fiscal 1997. Test drilling into the structure, construction work for research, and analysis (No.B-4 Kuenohira district); 1997 nendo chinetsu kaihatsu sokushin chosa. Kozo shisui chosa koji oyobi kaiseki hokokusho (No.B-4 Kuenohirayama chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-06-01

    Cuttings from a test drilling in the Kuenohira district, Oita Prefecture, are subjected to analysis. The result of ground surface investigation suggested the presence of a magma reservoir to serve as heat source and a highly permeable zone along a fault to help the formation of a thermal water retention system. At the N9-KH-1 drilling site, however, no geothermal reservoir is found along the periphery of the subsidence in the western part of the research area. In this district, it is deemed, no geothermal reservoir has been formed due to shortage of heat supply from the heat source and insufficient geothermal water activity. It is also deemed that the district, in which fractures of the E-W system, NNW-SSE system, and NE-SW system are distributed, is a region at which meteoric water flows into larger convection systems. As for the westward stretch of the geothermal reservoir (where the N9-KH-1 site is situated) that has developed on the swell of the basement, detected to exist at N2-MW-2 and N3-MW-6 in the eastern part of the research area, it is found to be not so extensive. (NEDO)

  13. Application of forking genetic algorithm to the estimation of an S-wave-velocity structure from Rayleigh-wave dispersion data. With special reference to an exploration method using microtremors; Rayleigh ha no bunsan data kara S ha sokudo kozo wo suiteisuru inversion mondai eno kotaigun tansaku bunkigata identeki algorithm no tekiyo. Bido tansaho ni kanrenshite

    Energy Technology Data Exchange (ETDEWEB)

    Cho, I; Nakanishi, I [Kyoto University, Kyoto (Japan); Ling, S [Nihon Nessui Corp., Tokyo (Japan); Okada, H [Hokkaido University, Sapporo (Japan)

    1997-10-22

    Discussions were given on a genetic algorithm as a means to solve simultaneously the problems related to stability of solution and dependence on an initial model in estimating subsurface structures using the microtremor exploration method. In the study, a forking genetic algorithm (fGA) to explore solid substance groups was applied to the optimizing simulations for a velocity structure model to discuss whether the algorithm can be used practically. The simulation No. 1 was performed by making the number of layers four for both of the given velocity structure and the optimizing model. On the other hand, the simulation No. 2 was executed by making the number of layers for the given velocity structure greater than that for the optimizing model. As a result, it was verified that wide range exploration may be possible for the velocity structure model, and that a large number of candidates for the velocity structure model may be proposed. In either case, the exploration capability of the fGA exceeded that of the standard simple genetic algorithm. 8 refs., 4 figs., 2 tabs.

  14. Study of reciprocating engine with Z mechanism. Part 1. Discussion of effect on the performances of new concept engine; Yodo shiten riron wo mochiita ofuku do engine ni kansuru kenkyu. 1. Shinkihon kozo no donyu ni yoru seino kojo no suisatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yoshizawa, Y; Fukuzaki, S; Kanno, M [Yoshiki Industrial Co. Ltd., Yamagata (Japan)

    1997-10-01

    A new reciprocating engine was developed as an application of new mechanism named as `Z mechanism.` In this new engine, the piston motion is described by a simple sine function and gives lower velocity around top dead center than that in conventional piston engines. Thus, the mode of combustion in this engine is closer to constant-volume process and gives higher thermal efficiency than ordinary engines. Use of Z-mechanism also eliminated high-order components of vibration that ordinary engines suffer. Development high-performance engine was successfully conducted with this new mechanism. 4 refs., 11 figs., 1 tab.

  15. Research and development of a technology to create original high-function materials in fiscal 1998 (development of precision structure controlling materials by improving petroleum refining). Report on achievements in research and development of precision catalytic polymerization; 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho. Sekiyu seisei kodoka seimitsu kozo seigyo zairyo kaihatsu (seimitsu shokubai jugo no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Research and development on precision catalytic polymerization aims at developing polymerizing catalysts that can control arbitrarily the molecular weight and three-dimensional regularity by which rapid enhancement can be expected in performance of additional polymerization type polymers, and the primary structure of terminal groups. Works are being done on two sub-themes of ultimate additional polymerization and orientation catalyst polymerization. The research and development of the ultimate additional polymerization included structural control in polymerization reaction in vinyl chloride, vinylester and acrylic monomers, radical polymerization with precision orientation control, anionic polymerization with precision structural control, and precision polymerization utilizing asymmetric metal porphyrin complexes. In the research and development of the orientation catalyst polymerization, the orientation catalyst polymerization was researched and developed, elementary reaction of metallocene was elucidated, high-performance carrier catalysts were developed, advanced function polymers were synthesized at high precision based on metathesis, and improvement of functions of polyolefin was researched and developed. Surveys and studies were carried out on fundamental technologies common to the above two themes re-commissioned to five universities. (NEDO)

  16. Fiscal 1999 achievement report on the venture business assisting type regional consortium - Minor business creation base type. Development of hypersensitive photocatalyst using oxide semiconductor thin film having nanostructure; 1999 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Nano bisai kozo wo yusuru sankabutsu handotai usumaku ni yoru chokokando hikari shokubai no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The thin film structure of photocatalytic titanium oxide, capable of efficiently decomposing hazardous pollutants or the like, is refined to have a nanometric scale structure for a larger specific surface for the development of a photocatalytic thin film or powder film and for the development of decomposition capable air cleaner using a thus developed photocatalytic film. Described in this report are the results of a study conducted to elucidate the fabrication conditions, nanostructures, and photocatalytic features of titanium oxide thin films formed by spray thermolysis, RF (radio frequency) sputtering, reactive sputtering, and sol-gel process, a study of hazardous pollutant decomposing capability and nanostructure, the establishment of fabrication technologies, and the construction of a prototype air cleaner with the results of the said studies applied thereto. Among the various fabrication methods, the technology involving a hypersensitive thin film photocatalyst was established by combining the reactive sputtering method and the sol-gel method. It was found that the formation of prismatic crystals in the sol-gel method was the most important in achieving high performance in the hypersensitive thin film photocatalyst. (NEDO)

  17. Fiscal 1999 achievement report. Important regional technology research and development--Research and development of eco-tailored tribo-material creation process technology (High-order composite structure material creation process technology); 1999 nendo eco tailored tribo material sosei process gijutsu seika hokokusho. Koji fukugo kozo material sosei process gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development is carried out for the creation of tribo-materials light in weight and free of harmful substances for the manufacture of brakes and rolling bearings for transportation equipment. In the study of the manufacture of tribo-materials by the powder sintering process, various intermetallic compound powers of Fe, Ti, and Al are prepared and sintered by the mechanical alloying method and the gas atomization method, and the compounds are examined for mechanical and tribological properties. In the study of the melting method, different specimens of the same alloy are melted and cast using high frequency, plasma arc, etc., and their mechanical properties and tribological properties are measured. In the study of the manufacture of brake disk materials and the manufacturing process, a small high-temperature abrasion tester is experimentally built and installed, and friction test materials free of Cu and Sb, suitable for the construction of light-weight rotors, are manufactured and tested for abrasion. In the study of the manufacture of materials for roller bearings and the manufacturing process, candidate materials are selected, pulverized by gas atomization, mechanical alloying, etc., and then sintered, and are tested for their bonding capability. (NEDO)

  18. Applicability of the spatial autocorrection method for estimation of basement structure in Kanto plain. Array measurements of microtremors close to the Iwatsuki and Shimosa deep borehole observatory; Kanto heiya no kiban kozo suitei no tame no kukan jiko sokanho no tekiyosei. Iwatsuki Shimosa jiban katsudo kansokusei ni okeru array bido kansoku

    Energy Technology Data Exchange (ETDEWEB)

    Matsuoka, T; Umezawa, N; Shiraishi, H [Saitama Institute of Environmental Pollution, Saitama (Japan)

    1996-10-01

    To investigate applicability of the spatial autocorrection method which is a microtremors exploration method for the estimation of basement structure, array measurements of microtremors were performed using the Iwatsuki and Shimosa deep borehole observatory where detailed structures were clarified as well as the Fuchu and Koto deep borehole observatory. In this study, estimated velocity structures of S-wave were compared with the geological sequence and results of acoustic velocity logging. The phase velocity was estimated by the spatial autocorrection method using FFT. The phase velocity with a smooth normal dispersion was observed in the periodic range from 0.5 to 5 sec in Iwatsuki, and from 0.5 to 4 sec in Shimosa by the combination of four-point circular arrays with radii of 100, 300, and 600 m. The underground structures estimated from the phase velocities coincided well with the geological sequence, and results of acoustic velocity logging and velocity logging for each borehole. For the Iwatsuki borehole, the basement velocity was also estimated properly in the periodic range of observation. While, for the Shimosa borehole, measurements with the period around 6 sec were required to estimate the basement velocity more accurately. 13 refs., 11 figs., 1 tab.

  19. FY1998 results report on the priority area research and development of 'innovative processing technologies for producing ecologically tailored tribo-materials'. Innovation processing technologies for producing high-order composite structured material; 1998 nendo eco tailored tribo material sosei process gijutsu seika hokokusho. Koji fukugo kozo material sosei process gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With research and development conducted for the purpose of improving performance of tribology-related parts in outdoor industrial equipment and transportation machinery, the results for fiscal 1998 were summarized. In the trial manufacturing of tribo-materials by a powder metallurgical method, since Fe-Ti-Al based intermetallic compound was promising, four kinds of powder samples were manufactured by mechanical alloying. Tribo-materials by a melting and casting method were also manufactured using the same samples and found to be inferior to the powder sintered materials in dynamic properties. In the evaluation of trial manufacturing of materials for brake disks, the result of measurement on abrasion loss and a friction coefficient by a high temperature abrasion tester revealed that Ti-Al based alloys were promising as composition metal. In the examination of the trial manufacturing of materials for bearings, in dealing with high loading of bearings, investigations were conducted on the physical properties of a low carbon steel backing with heating and rolling applied as well as on overlay materials. For materials for bearing alloys, Cu based powders were examined which were manufactured by a gas atomizing method. (NEDO)

  20. Fiscal 2000 report on result of R and D of industrial science and technology that creates new industry. Development of supermetal technology (development of nano-amorphous structured material); 2000 nendo super metal no gijutsu kaihatsu seika hokokusho. Nano amorphous kozo seigyo zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    R and D was conducted for the purpose of manufacturing innovative iron-based alloy materials that excel in high temperature strength, toughness and superplastic forming, with fiscal 2000 results compiled. In the technological study on high-speed grain accumulation and superplastic forming, the researchers were engrossed in developing an aluminum bulk material of nano-crystals. This year, an Al-Fe two-element based alloy using Fe element was evaluated in the composition, thermal processing conditions and physical properties, with a bulk material obtained having a grain size of several tens in nm at 2at% Fe level, a strength of 750-850 MPa and a tenacity (Kc value) of 45-65 MPa(center dot)m{sup 1/2}. In the research of technologies for utilizing and controlling high density energy, design of materials was progressed for strong-acid resistant dew point corrosion materials, leading to the discovery of an alloy composition Ni-10Cr-5Nb-16P-4B whose subcooled liquid zone was wider than the Ta-added alloy of the previous year. Use of He gas as injection gas enabled a quality amorphous powder to be obtained in kg units. In the development of bulk amorphous producing technologies, this powder was thermostatically rolled to make a dense bulk amorphous plate of 2.8 mm thick and about 100 mm long. (NEDO)

  1. Fiscal 1998 research report on the R and D on industrial science and technology for creating new industries. R and D on intelligent material and structure systems; 1998 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki zairyo kozo system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project aims at development of the basic technology of the structure system which has the same intelligent functions as living body such as perception, decision and response through information processing/control (brain) by integrating advanced complex material structure (skeleton), fiber or film sensor material/device (nerve) and actuator material/device (muscle). This report describes the fiscal 1998 research result. On health monitoring technology, study was made on development of high-performance sensors, and a damage detection and self-diagnosis system for structural integrity. On active adaptive structure technology, study was made on improvement of a quasi-elastic behavior model for shape memory alloys, and a candidate actuator for noise and vibration reduction. On actuator materials and devices, study was made on the relation between electronic properties and dielectric/electro-strictive characteristics of the latest advanced ceramic materials available. Creation of silent smart structure was also clarified. Smooth connection and cooperation among groups were promoted through the technical committee and research on domestic and overseas trends. (NEDO)

  2. FY 2000 report on the results of the research and development project for utilization of information of high-molecular-weight structures in a living body. Survey on the technological trends of utilizing the reactions with metals in a living body; 2000 nendo seitai kobunshi kozo joho riyo gijutsu kaihatsu chosa hokokusho. 'Seitai kinzoku hanno riyo gijutsu' ni kansuru gijutsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 2000 results of the survey on the technological trends of utilizing the reactions with metals in a living body, noting the bio-processes effectively coping with the environmental problems. The effects of heavy metals on microorganisms have been investigated on the molecular biology level, but are not fully elucidated. Recently, the microorganisms capable of converting inorganic metal ions in water into the insoluble compounds have been known, leading to possibility of bioremediation to solve pollution by heavy metals, which have detrimental effects on human health. Heavy metals must be recovered, because they are not extinct by decomposition. The plant aided purification has been attracting attention to cope with heavy metals accumulated in soil. Application of bacteria-aided leaching, which is adopted as one ore smelting process, to the technologies for utilizing metals in a living body has been expected, because diversified activities of inanimate matters in extreme environments have been known. Recently, bio-machining of metals aided by Thiobacillus ferrooxidans, one species of independent nutrient bacteria capable of eating metals, has been developed to a potentially viable stage. (NEDO)

  3. Research and development of system to utilize photovoltaic energy. Survey on the high-durability and low-cost materials for constructing the solar-cell module and its structure; Taiyoko hatsuden riyo system no kenkyu. Taiyo denchi module yo kotaikyusei tei cost zairyo, kozo ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the results obtained during fiscal 1994 on a survey on the high-durability and low-cost materials for constructing the solar-cell module and on its structure. With respect to forms and materials used in the present solar-cell modules, identification was made on the current status of products commercially available and developed inside and outside Japan. Main types of solar cells used for electric power are of crystal-based silicon. Amorphous silicon and CdS-CdTe are used for consumer applications of indoor and outdoor use. As regards transparent resin materials, fluorine resin, PET, acryl, and polyimide are used as surface materials, and EVA, silicon and PVB are often used as fillers. Developments inside and outside Japan are limited to systems of polycarbonate, methacryl, fluorine, polyurethane, acryl and polyester. Butyl rubber and polyurethane are used as sealing materials. Developments are being performed on silicon rubber, polychloroprene rubber and EPT rubber for shaped materials, and silicon systems, urethane systems and polysulfide systems for non-shaped materials. 3 figs., 8 tabs.

  4. Study on unified fatigue strength assessment method for welded structure. Hot spot stress evaluating method for various combinations of plate thickness and weld leg length; Yosetsu kozo no toitsutekina hiro kyodo hyokaho ni kansuru kenkyu. Itaatsu to yosetsu ashinaga no kumiawase ni taisuru hot spot oryoku sanshutsu ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Nihei, K.; Inamura, F.; Koe, S. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

    1996-12-31

    There has been tried to apply unified assessment method using hot spot stress, which is effective to evaluate fatigue strength of fillet welded structures for ships and marine structures. This method can be applied to complicated structures and is independent of welding processes. In this study, first, stress analysis has been conducted for two-dimensional fillet welded joint models with various combinations of plate thickness and weld leg length of general fillet structures by means of boundary element method. Then, critical position, which is not affected by local stress concentration due to bead, was determined from the detailed stress distribution in the vicinity of weld toe. As a result, a general equation has been proposed to estimate the hot spot stress by one-point representative method. Second, the fatigue tests of typical fillet welded joints have been conducted by applying this method. Consequently, it was demonstrated that the unified fatigue strength can be evaluated by the S-N data based on hot spot stress range determined from the proposed equation, independent of structural stress concentration. 22 refs., 14 figs.

  5. 1998 report on results of technological development of super metal. Innovative technological development for producing advanced structure controlled metallic material (high-speed large reduction rolling technology); 1998 nendo super metal no gijutsu kaihatsu seika hokokusho. Kodo soshiki kozo seigyo kinzoku zairyo sosei gijutsu kaihatsu (kosoku daiatsuka atsuen gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A report was made on the 1998 results concerning technological development of super metal. In the 'research and development of super metal', metallurgical examination has been made on crystal grain super refining process using a machining simulator, with studies carried out on crystal grain refining by utilizing large-strain deformation with more than 50% deformation for a single pass and a diploid structure. As a result, it was found that the crystal grain size can be refined to approximately 1{mu}m. Consequently, in fiscal 1998, a high-speed large reduction rolling test equipment was developed capable of rendering a sheathing technology in a mechanically testable size by a rolling method. This test equipment has such capacity as the maximum load of 1,000 ton and the maximum torque of 95 ton/m and is a rolling mill whose scale is largest in the nation on the laboratory level. The rolling speed can be 120mpm, a very fast speed for a large sized rolling mill. Moreover, equipped with an immediate water cooling facility adjacent to the rolls and an automatic operating system for example, it is a high function rolling mill capable of cooling and rolling that render the complex and delicate sheathing technology of super metal. (NEDO)

  6. Energy supply/demand structure development survey project / comprehensive survey on energy supply/demand development. FY1997 survey on techniques for pyroelectric power generation systems; Energy jukyu kozo kodoka chosa jigyo / energy jukyu kodoka sogo chosa. 1997 nendo shoden hatsuden system no gijutsu chosa seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    Pyroelectric conversion systems were surveyed as the techniques for effective utilization of low-temperature waste heat sources. Described herein are the principle of pyroelectric power generation, including pyroelectric phenomenon, origin of pyroelectricity in polymers, and pyroelectric polymers and copolymers; utilization of the pyroelectric phenomenon, including hysteresis of pyroelectric materials, general pyroelectric conversion principle, pyroelectric conversion cycle, analysis of power output by an Olsen cycle, comparison with a steam engine, and power outputting methods; pyroelectric conversion systems, including heat regeneration method, plate type pyroelectric conversion devices using the heat regeneration method, and voltage controlling methods; and pyroelectric conversion outputting, including calculations of power output and loss, conduction-caused loss, pumping loss, and pyroelectric converter efficiency. Other items described herein include conceptual designs of 1 and 100 kW pyroelectric converters for utilization of waste heat, and current status of pyroelectric converter development at CANMET Energy Technology Center. (NEDO)

  7. Fiscal 2000 achievement report on the important regional technology research and development. Research and development of eco-tailored tribo-material creation process technology (Higher order composite structure material creation process); 2000 nendo juyo chiiki gijutsu kenkyu kaihatsu seika hokokusho. Eco tailored tribo material sosei process gijutsu (koji fukugo kozo material sosei process gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are made to develop novel tribo-material creation processes through the application of an inclined constitution/structure control, a nonstoichiometric constitution control, or the like, to the manufacture of materials having excellent tribological characteristics for the purpose of improving on the performance of tribology related parts. In fiscal 2000, activities are conducted in the four fields of (1) the experimental manufacture of tribo-materials by powder sintering and the review of the process, (2) the experimental manufacture of tribo-materials by melting and the review of the process, (3) the experimental manufacture of brake disk materials and the review of the process, and (4) the experimental manufacture of bearing materials and the review of the process. In field (1), the preparation of an Fe{sub 3}Al/FeAl intermetallic compound powder by mechanical alloying and gas atomization and the conditions of pressure sintering by HIP (hot isostatic press) or the like are established. Concerning the melting method, basic techniques are established and an experimentally built rotor is evaluated for braking characteristics. In field (3), efforts are made to develop Cu/Sb free brake linings that will match TiAl-made rotors and then an MgO/C system is discovered, which is found to be on the same level as the conventional materials. (NEDO)

  8. Achievement report for fiscal 1998 on the development of super-metal technology. Development of technology of high corrosion-resistance iron base controlled microstructure materials; 1998 nendo super metal no gijutsu kaihatsu. Kotaishokusei tetsukei bisai kozo seigyo kinzoku zairyo gijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    During ultrafine structure formation due to transformation from austenite to ferrite in an intense magnetic field, the transformation is accelerated by the thermodynamic stabilization of the ferrite phase which is ferromagnetic. The application of an intense magnetic field works effectively during the generation of nuclei. When a magnetic field is applied during reverse transformation, a honeycomb 2-phase structure is formed oriented toward the direction of the magnetic field and, when the structure is vertically compressed, the recrystallized structure is made ultrafine effectively. In pearlite transformation, hardening occurs when carbon atoms supersaturated in density are introduced in the presence of a magnetic field gradient, and curing further promotes precipitation hardening. In a ferrite complex phase system, wherein ultrafine globular cementite is uniformly distributed, plastic instability becomes explicit in a tensile test. There is a good possibility that an ultrafine structure recrystallization model may be built by calculation, into which the distribution of energy stored prior to recrystallizing nucleus formation is incorporated. The profile of a conceptual process of off-line or in-line integration of heavy-strain process and intense magnetic field application has become tangible. (NEDO)

  9. Mechanism of spark generation from Japanese toy firework (senko-hanabi). ; Structural-Oxidizing reaction of micro graphite crystals in molten K sub 2 Sn. Senko hanabi no jikkenteki kosatsu. ; Yoyu K sub 2 Sn chu no sekiboku bikessho no kozo teki sanka hanno

    Energy Technology Data Exchange (ETDEWEB)

    Ito, H. (The University, of Tokyo, Tokyo (Japan))

    1991-12-20

    Considerations were given on the spark generating mechanism of graphite particles in molten salt polysulfide through experiments on Japanese sparklers. The firework composition mixed consisted of two kinds: KNO{sub 3}, S, amorphous carbons, charcoal and lamp black, and K{sub 2}CO{sub 3}, S, charcoal and lamp black. The main constituent in fire balls is molten salt polysulfide. The O{sub 2} generated from combustion oxidizes C and S, whereas the generated K{sub 2}CO{sub 3} reacts with S to produce K{sub 2}Sn. In the KNO{sub 3} system, the calorific power reaches the maximum with lamp black contained at 10-15%. This is thought because the K{sup +} expands the space between the graphite crystal layers making the oxidation to take place more easily into their inner sides. On the one hand, the calorific power reduced with the lamp black at more than 16% would be because the lamp black clogging the crystalline spaces restricting the oxidation. It is thought that condensation and decomposition of micro graphite crystals occur simultaneously in the fire balls. It is also believed that the micro graphite crystals jumped out as a result of gas pressure from inside the crystals generated with the progress of oxidation break off at once because of the resistance of air together with the effect of the K{sup +} in the salt polysulfide (mutual separation of each layer). 9 refs., 6 figs., 1 tab.

  10. FY 1998 annual report on the results of new industry creation type industrial science and technology research and development on the research and development of supermetals. Development of techniques for controlling structures of nano-amorphous materials; 1998 nendo super metal no gijutsu kaihatsu. Nano amorphous kozo seigyo zairyo no gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Described herein are the FY 1998 results of the development of techniques for controlling structures of nano-amorphous materials. For the development of techniques for finely dispersing fine particles, mechanical alloying (MA) and mechanical milling (MM) are investigated, to structure nano-crystals in common steel, for which hot isostatic pressing is evaluated as a consolidation process for the MA- and MM-prepared powders in the FY 1998. For researches on high-speed particle deposition and super plastic forming, an Al-Ni, Al-Fe and Al-Ti alloy are selected as the nano-structure materials to be prepared by evaporation, and various compositions of these systems are evaporated, in order to investigate their microstructures, mechanical properties and thermal stabilities. For researches on techniques for controlling phases with the aid of high-density energy, the R and D efforts are directed to exploration of composition of high resistance to corrosion by acid at dew point, preparation of non-equilibrium (e.g., amorphous) powders, and development of solidification and forming techniques, with the target of creation of an amorphous alloy showing corrosion resistance at least twice as high as that of the commercial corrosion-resistance material and formable into a bulk shape having a thickness of at least 1 mm. For researches on controlled cooling techniques, the basic data are collected. (NEDO)

  11. Study on unified fatigue strength assessment method for welded structure. Hot spot stress evaluating method for various combinations of plate thickness and weld leg length; Yosetsu kozo no toitsutekina hiro kyodo hyokaho ni kansuru kenkyu. Itaatsu to yosetsu ashinaga no kumiawase ni taisuru hot spot oryoku sanshutsu ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Nihei, K; Inamura, F; Koe, S [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

    1997-12-31

    There has been tried to apply unified assessment method using hot spot stress, which is effective to evaluate fatigue strength of fillet welded structures for ships and marine structures. This method can be applied to complicated structures and is independent of welding processes. In this study, first, stress analysis has been conducted for two-dimensional fillet welded joint models with various combinations of plate thickness and weld leg length of general fillet structures by means of boundary element method. Then, critical position, which is not affected by local stress concentration due to bead, was determined from the detailed stress distribution in the vicinity of weld toe. As a result, a general equation has been proposed to estimate the hot spot stress by one-point representative method. Second, the fatigue tests of typical fillet welded joints have been conducted by applying this method. Consequently, it was demonstrated that the unified fatigue strength can be evaluated by the S-N data based on hot spot stress range determined from the proposed equation, independent of structural stress concentration. 22 refs., 14 figs.

  12. Utilização do intercepto-y na avaliação da aptidão anaeróbia e predição da performance de nadadores treinados El uso del intercepto-y en la evaluación de adaptacion anaeróbica en la predicción de la performance de nadadores especializados Use of the y-intercept in the evaluation of the anaerobic fitness and performance prediction of trained swimmers

    Directory of Open Access Journals (Sweden)

    Marcelo Papoti

    2005-04-01

    Full Text Available O objetivo desse estudo foi verificar a utilização do intercepto-y na avaliação da aptidão anaeróbia e predição da performance de nadadores treinados. Foram participantes do estudo 14 nadadores com idade entre 15 e 18 anos. Os atletas realizaram o teste de nado atado, performance máxima e velocidade crítica (VC para determinação da capacidade de nado anaeróbio (CTA, todos em nado crawl em um período de três dias. 1 O teste de nado atado consistiu em realizar esforço máximo durante 30 segundos amarrado a um aparato de medição com células de carga para mensuração da força pico (Fpic, aptidão anaeróbia (AP ANA e concentração de lactato pico ([la-]pic conforme Papoti et al. (11; 2 Os participantes realizaram também performances máximas nas distâncias de 100, 200, 300, 400 e 600 m, com intervalo mínimo de duas horas entre cada nado; 3 E o teste de VC foi aplicado para determinação da CTA utilizando todas as combinações possíveis dos resultados das performances máximas, através do modelo de regressão linear entre distância versus tempo. Foi encontrada média de 25,07± 4,22 m nas 16 combinações de CTAs encontradas e coeficiente de regressão linear variando entre 0,99 e 1,00 e erro de coeficiente linear de 19,30± 5,9%. Não foram encontradas correlações significativas entre as CTAs e performances máximas, Fpic (227,81± 63,02 N, AP ANA (86,55± 13,05 N e [la-]pic (6,80± 1,03 mM. Contudo, foram encontradas correlações significativas entre a AP ANA e as performances máximas. Desse modo, é possível concluir que a CTA representada pelo intercepto-y da relação distância versus tempo de nado, parece não ser um bom parâmetro na avaliação da aptidão anaeróbia e predição de performances entre 100 m e 600 m nado crawl.El objetivo de ese estudio fue verificar el uso del intercepto-y en la evaluación anaeróbica de la aptitud y predicción de la performance de los nadadores especializados. Los

  13. Descrição da aptidão inicial para natação em lesionados medulares Description of initial swimming ability in patients with spinal cord injury

    Directory of Open Access Journals (Sweden)

    Ana Cláudia Raposo Melo

    2009-12-01

    Full Text Available Este estudo tem por objetivos verificar o retorno à natação após a lesão medular e descrever a aptidão inicial de lesionados medulares para o nado como parte das atividades do programa de reabilitação no Hospitalar Sarah-Centro. MÉTODOS: Foram avaliados 170 pacientes com diagnóstico de paraplegia e tetraplegia, em três etapas - levantamento de dados em prontuário, entrevista oral e avaliação do padrão do nado. Os resultados apontaram que grande parte dos pacientes não entrou na piscina ou realizou nado após a lesão medular. A avaliação da adaptação ao meio líquido após a lesão medular demonstrou que grande parte dos pacientes realizou a imersão e flutuação de forma independente, porém, apresentando dificuldade em mudar de decúbito dentro da água. Apenas uma pequena porcentagem retomou a natação após a lesão medular; foi também verificada redução no total dos sujeitos que nadavam regularmente antes. A avaliação apontou que os nados crawl e de costas foram realizados por metade dos avaliados; apenas uma pequena parte realizou nado de peito. CONCLUSÃO: Após a avaliação dos relatos dos pacientes, verificou-se redução na prática da natação, seja como atividade esportiva, física ou de lazer após a lesão medular, apesar de a aptidão para o nado não ter sofrido grandes alterações.Pysical activity, particularly swimming, that brings a lot of benefits to subjects with spinal cord injury, can be started during rehabilitation. The aims of this study were to describe the initial ability to swim of patients with spinal cord injury during the rehabilitation program at the Sarah Hospital - Center. METHODS: 170 patients were evaluated in three steps - medical records data collection, oral interview and swimming evaluation. The results showed that a large proportion of patients did not enter the swimming pool or swam after spinal cord injury. Only a small part returned to swimming after the spinal cord

  14. Quistes radiculares. Posibilidad de tratamiento endodóncico

    OpenAIRE

    Canalda Sahli, Carlos; Canalda Piera, Carlos

    1981-01-01

    Las principales complicaciones apicales y periapicales de la gan­grena pulpar, son la periodontitis apical crónica y el quiste radicular. Representan el 90 por ciento del total de lesiones apicales (BHASKAR). El 10 por ciento restante, corresponde a lesiones mucho menos habi­tuales: cementoma, absceso alveolar, quiste residual, tumor de células gigantes, etc. El tratamiento del granuloma y del quiste radicular ha evolucio­nado en el tiempo en un sentido más conservador. La existencia de una l...

  15. Sexualidad y transexualidad - Desafíos en la formación en pedagogía

    OpenAIRE

    Marques Santos, Vera Márcia; cnte

    2016-01-01

    Este texto defiende la urgencia de refutar la intolerancia y la discriminación, abordando reflexiones que explicitan la dinámica de una asignatura en la licenciatura:Conversando sobre la Sexualidad Adolescente. El mencio nado texto refleja el dramade profesionales de la educación, dentro del proceso de formación inicial, en la discusión del tema sexualidad en la adolescencia, especialmente, en lo que se refiere a  transexualidad, mostrando cómo estas académicas percibieron y sintieron el tema...

  16. Efectos sobre el sistema nervioso central del extracto etanólico y fracciones de hygrophila tyttha leonard

    OpenAIRE

    Ariza, Sandra Y; Rincon, Javier; Guerrero, Mario F

    2008-01-01

    Se evaluó en ratones albinos ICR el perfil de actividad que sobre el sistema nervioso central ejercen el extracto etanólico y las fracciones acuosa, clorofórmica, metanólica y hexánica obtenidas de Hygrophila tyttha (Acanthaceae. NV: amansamachos). Para tal fin se utilizaron pruebas destinadas a detectar posible actividad ansiolítica (laberinto en cruz elevado), antidepresiva (nado forzado), anticonvulsivante (pentilentetrazol, electrochoque) e hipnótica (potenciación de sueño inducido por pe...

  17. Biorremediacion de suelos contaminados con hidrocarburos

    OpenAIRE

    Ortiz, E.; Núñez, R.; Fonseca, E.; Oramas, J.; Almazán, V.; Cabranes, Y.; Miranda, A.; Barbán, O.; Martínez, C.; Díaz, Y.; Borges, G.

    2005-01-01

    En la actualidad los suelos contaminados con hidrocarburos representan el 70% del total de los eco-sistemas impactados. A partir del aislamiento, selección y conservación de bacterias marinas degra-dadoras de hidrocarburos y productoras de sustancias tensioactivas se formuló un producto denomi-nado BIOIL-FC. Este producto ha sido aplicado satisfactoriamente en derrames de hidrocarburos en el mar. En el presente trabajo fue evaluada la factibilidad del uso de los procesos de biorremediación “e...

  18. Breve historia reglamentaria del estilo pecho

    OpenAIRE

    Britez, Julián

    2013-01-01

    La natación a nivel mundial se ha convertido en un espectáculo único acaparando la mirada de todos durante los Juegos Olímpicos y Mundiales, esto ha sido sostenido principalmente por la pulverización constante de records. El estilo Pecho o Braza, es considerado el más lento de los cuatro estilos de nado reconocidos por la Federación Internacional de Natación. Pero con el avance de los años, la organización rectora de la natación a nivel mundial ha ido incorporando cambios y modificaciones con...

  19. Report on a survey in fiscal 1999. Survey on possibilities of environmental cooperation in relation with proliferation of environment preservation technologies and institutions in developing countries; 1999 nendo kankyo taisaku gijutsu seido nado no tojokoku fukyu ni kakawaru kankyo kyoryoku kanoseichosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Cooperation in energy and environment aspects with developing countries is considered very important in view of the following points: (1) the cooperation will help developing countries to grow economically while minimizing the damages from industrial pollution and environmental problems; (2) conservation of energies and promotion of use of new energies will contribute to solving pollution problems associated with energy production, and will result in assurance of stability of primary energy availability for Japan; (3) preservation of environments in countries exporting foods to Japan will link to maintaining health of Japanese people and increasing their welfare; and (4) Japanese industrial pollution preventing technologies and knowledge whose levels are high worldwide may be utilized to create new business chances for Japanese business entities. The present survey has discussed the importance by territories, the importance by cooperation modes, and sharing of roles by governmental and private organizations, and performed case studies. Considerations were given from the discussion results on how the environmental projects should be planned in the environment cooperation, the contents to be of win/win from the viewpoint of motivation, the project image for subjected territories being composite and comprehensive, and the cases from the viewpoint of mutual coexistence referred to as prevention of global warming and assurance of food and energy resources. (NEDO)

  20. FY 2000 report on the basic survey to promote Joint Implementation, etc. Energy conservation by modernization of a cement plant (Double Horse Cement Co.) in China; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Chugoku cement kojo (Double Horse Cement) kindaika ni yoru sho energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    An investigational study was conducted of possibilities of energy conservation and greenhouse effect gas emission reduction in the cement production process of Double Horse Cement Co., Mianyang City, Sichuan Province, China. Double Horse Cement adopts the wet type long kiln production system and has a production ability of approximately 1.5 million t/y. In the project, as to three production lines out of the six production lines, improvement was planned to be made of the technologies on the following: mixing of raw materials, grinding of raw materials, NSP, clinker cooler, clinker pre-grinder, high-efficiency separator, waste heat use power generation, etc. As a result of the study, it was found that the energy conservation amount obtained was 54,646 toe/y. And, the amount of greenhouse effect gas reduction was 169,086 t-CO2/y. The total fund required for this project was approximately 5.553 billion yen and the internal earning rate was 7.36% after tax. When the project is carried out, expenses vs. effects are 9.8 toe/million yen in energy conservation amount and 30.4 t-CO2/million yen in greenhouse effect gas reduction. (NEDO)

  1. FY 2000 report on the basic survey to promote Joint Implementation, etc. Survey for prevention of pollution by caustic soda in the mercury process and for heightening of efficiency; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Suiginho kasei soda kogai boshi koritsu kojo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In relation to facilities of Azerchimia, state concern, in Sumgait City, Azerbaijan, an investigational study was conducted of the project for energy conservation and greenhouse effect gas emission reduction by converting the caustic soda plant from the mercury process to the ion exchange process. The facilities of Azerchimia are badly superannuated and consume much more electric power than those in the newest technology. Moreover, the soil pollution by the plant using the mercury process is becoming a big problem. By carrying out this project, energy conservation can be achieved by reducing the amount of purchased power from thermal power plants outside. As a result of the study, the amount of the fuel used at the power plant was reduced to 40,700 toe/y. And, the amount of greenhouse effect gas emission was reduced to 131,000 t-CO2/y. In the study of the profitability, the internal earning rate of investment after tax was 8.6% and the internal earning rate of fund was 40% in the case of soft loans. In the case of commercial loans, however, they were 8.6% and 9.4%, respectively, which indicated that the materialization of the project was low. (NEDO)

  2. Fiscal 1998 research report. International measures project for rational energy use (Survey project of the analysis tool of Asian energy consumption efficiency); 1998 nendo chosa hokokusho. Kokusai energy shiyo gorika nado taisaku jigyo (Asia energy shohi koritsuka bunseki tool chosa jigyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-02-01

    This project aims to prepare the inter-industry relations table and analysis model for energy analysis for every Asian country, and analyze the relation between energy consumption and industrial structure or final demand structure. The 1985 and 1990 inter-industry relations tables of each country were prepared in cooperation with the governmental organizations of China, Korea, Taiwan, Philippines, Thailand, Malaysia, Singapore and India. However, the 1987 and 1990 tables were prepared for China. In fiscal 1998, the project invited the representatives of each concerned organization, and held the international workshop together with Japanese specialists to discuss various issues related to not only table preparation but also data analysis. The following items were analyzed for every country: a change in final energy consumption, a dependence on coal in primary energy consumption, transfer of energy consumption to other energy resources, and an energy consumption rate in the whole industry. (NEDO)

  3. Report on FY 1998 project for international energy utilization rationalization, etc. (Project of the analytical tool survey for making energy consumption effective in Asia); 1998 nendo chosa hokokusho. Kokusai energy shiyo gorika nado taisaku jigyo (Asia energy shohi koritsuka bunseki tool chosa jigyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In the Asian region, for the purpose of grasping effects of both economic growth and effective energy consumption, an analytical tool added with a computational function was developed with the interindustrial relations table as database for the analysis of the present situation and the simulational analysis. In the analysis of the present situation, changes between the two time-points, 1985 and 1990, were analyzed using the developed energy consumption table and the CO2 emission table. The energy consumption amount is increasing with the growing economy. However, the energy unit consumption is decreasing in countries except Korea, the Philippines, Singapore and Malaysia. The trend is that the energy consumption is becoming effective and the CO2 emission amount is decreasing. As an example of simulating the introduction effect of energy saving technology, the simulation was conducted on the three: iron steel, paper/pulp, and cement in Indonesia. As a result, the decrease in energy consumption was shown in paper/pulp by 48%, in cement by 16%, and in iron/steel by 16%. The same was also indicated in CO2 emission. (NEDO)

  4. Fiscal 1997 industrial technology R and D project. Research report on development of use technology of bio- resources such as complex biosystem (Development of use and production technologies of complex biosystems); 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei riyo seisan gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This project aims to establish production technology of functional substances, oil degradation and purification technology, and use technology of unused oil fraction through development of cultivation control technology of complex biosystems. For functional material production technology, as functional substances some specific marine bacteria inhibitors, antibreeding substances of microalgae, and UV absorption substances were isolated. The productivity of korormicin as specific inhibitor against marine bacteria was improved considerably by cultivation method. For research on molecular genetic analysis technology, a new identification technology and a simple automatic analysis system of microeucaryotes using genes were developed. For global environment purification technology such as efficient degradation of pollutants, study was made on cultivation control technology of phenol- degrading consortia, population dynamics of oil-degrading microbial consortia and a restoration method of oil pollution by complex biosystem at lower temperature, and the demonstration experiment of oil degradation were carried out. (NEDO)

  5. FY 1998 annual summary report on project for international energy consumption rationalization. Survey on analysis tool for improving efficiency of Asian energy consumption (data book 2 for 1985); 1998 nendo kokusai energy shiyo gorika nado taisaku jigyo chosa hokokusho. Asia energy shohi koritsuka bunseki tool chosa jigyo (shiryoshu 2 1985 nen data)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The data book is compiled, based on common industrial classifications, as the tool for analyzing, e.g., the mutual ripple effects of economic growth and increased efficiency of energy consumption throughout the Asia-Pacific region. This book summarizes the industrial-related and energy-related tables for 8 Asian countries and Japan. The book II is for the 1985 data (1987 data for China), comparing with the book I for the 1990 data. The industry-related tables are composed of the tables for transaction bases, input coefficients, final demand converters, importation coefficients, inverse matrices, sensitivity/influence coefficients, production inducement levels, production inducement coefficients, degrees of dependence on production inducement, importation inducement levels, importation inducement coefficients, and degrees of dependence on importation inducement. Energy-related tables are composed of the tables for, e.g., energy input, energy consumption, emissions, and CO2 emissions. (NEDO)

  6. Basic survey project of advanced efficiency of energy consumption in developing countries. Cooperation survey of efficient consumption of petroleum (survey of industrial foundation in the Philippines); Hatten tojokoku energy shohi koritsuka kiso chosa nado jigyo sekiyu shohi koritsuka kyoryoku chosa. Philippine koku sangyo kiso chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The purpose of the survey is to promote the international research cooperation projects from the survey stage, via demonstration research stage to the diffusion stage. Field surveys have been conducted to find out the needs of energy saving and environmental technology for the efficient consumption of petroleum in the developing countries with mass-consumption of petroleum in the future. The survey was conducted in the Philippines in the FY 1996. Next developing themes were proposed. The first theme was developing method of sugar plant. The magnesia method has been developed as a basic technology for cleaning sugar solution process instead of using lime. By the recycling method, the waste cake amount can be remarkably reduced. The second theme was electron beam exhaust gas treatment by a dry method of simultaneous desulfurization and denitrification of high concentration SOx and NOx in the fertilizer production plants. The third theme was the energy saving technology for SOx reduction of heating furnace for iron-steel by using an ultra energy saving-type regenerative burner. The last theme was chlorine bypass technology in cement industry, which would become an advanced technology development for the use of chlorine containing fuels in the near future. 40 refs., 36 figs., 79 tabs.

  7. Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy (Textile technology field)); 1999 nendo choki energy gijutsu senryku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (sen'i gijutsu bun'ya))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 basic research result on industrial technology strategy of a textile technology field. Social demand and constraint in the 21st century restrict human life and industrial activity, however, include huge business chances. This technology strategy aims at construction of textile business contributing to the society, and improvement of the international competitiveness of Japanese textile industry. Analysis was made on the current international competitiveness of the textile industry in comparison between Japanese and American productivity. As factors hindering technological innovation, the following were pointed out: poor cooperation among industry, academia and government, poor cooperation among different kinds of industries, poor preparation of basic technology, knowledge base and creation base, and poor deregulation. As the future target and strategy, 7 technology targets, 2 creation targets, and every target year were showed. 4 proposals were also showed as follows: preparation of a technology base, creation base, talent education and knowledge base, and protection of intellectual property rights. (NEDO)

  8. Fiscal 1998 research report on the demand forecast of rare element minerals, recycling technology of rare elements from waste, and substitute rare element minerals; 1998 nendo chosa hokokusho. Kisho genso koseki no juyo yosoku, kisho genso no haikibutsu kara no kaishu gijutsu oyobi daitai kisho genso koseki nado ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Rare element mineral is indispensable material for functionalization of high-tech raw materials. Its deposit is poor, an increase in its future demand is expected, and its information disclosure is insufficient because of strategic important material. To solve these problems, the following were studied systematically, and urgent research themes on rare element minerals were clarified: (1) High-efficiency recycling technology of rare elements, (2) Waste treatment system after recycling of rare elements from the viewpoint of environmental measures, (3) Establishment of the database of rare element minerals, and development of new substitute rare element minerals, and (4) Design method of substitute materials possible to generate various existing functions without any rare elements. Among them, in particular, precise separation of 46 kinds of rare elements from waste of high-tech raw materials, and recycling of rare elements from zinc refining waste and pyrite ore deposit containing copper were pointed out as important themes. (NEDO)

  9. Fiscal 1997 report on the results of the New Sunshine Project subsidiary operation. Development of a geothermal water use power plant, etc. / technical development of the hot dry rock power generation system (development of electric technology); 1997 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (koon gantai hatsuden system no gijutsu kaihatsu (yoso gijutsu no kaihatsu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of using hot dry rock energy to power generation, the R and D was continued of element technology of the hot dry rock power generation. In fiscal 1997, the construction of ground facilities, etc. for long-term circulation experiment was proceeded with to make data analysis for study of the experimental results. As for preparation for the long-term circulation experiment, design/fabrication/construction of experimental facilities were commenced, and review/fabrication of the monitoring system were conducted to strengthen the monitoring network of microearthquakes. In relation to the analytical research, using models connecting reservoirs and wells, relationships were studied among the distance between injection well and production well, production flow rate, and long-term thermal extraction characteristics of reservoirs. Further, to study structures of shallow/deep reservoirs at the Hijiori hot dry rock experimental field, re-determined were mechanism solutions of AE in deep hydraulic fracturing experiments, three well circulation tests, and preliminary circulation tests, and at the same time stress fields were studied. Fracture models were made and the simulation program was revised. 18 refs., 82 figs.

  10. Basic survey project for joint implementation in fiscal 1998. Study of BFG mono-firing gas turbine combined cycle power plant application for the steel mill of China; 1998 nendo kyodo jisshi nado suishin kiso chosa. Chugoku seitetsu kaishamuke koro gas sensho combined cycle hatsuden setsubi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Discussions were given on application to the steel mills in China of a 1100-degree C class high-efficiency combined cycle power plant (CCPP) exclusively firing blast furnace gas developed jointly by Kawasaki Heavy Industries Ltd. of Japan and ABB Corporation of Switzerland. The CCPP can utilize the energy possessed by a fuel without waste from high temperature zones to low temperature zones, being capable of attaining high efficiency that cannot be achieved with the single cycle. The CCPP has the efficiency exceeding that of the BTGP by about 10% or more in absolute value. The investigations and discussions were given on Shougang General Corporation, Anshan Steel Corporation and Wuhan Steel Corporation. As a result, in the plan for the power plant of Shougang General Corporation on which both parties have agreed, the project implementation can be expected to result in electric power generation of 110 MW in annual average, factory air supply of about 100 tons per hour in annual average, and annual reduction of carbon dioxide of 841 kilo tons. Wuhan Steel and Anshan Steel will require implementation of further detailed investigation, but the possibility of realization is considered high (NEDO)

  11. FY 1998 report on the verification survey of geothermal survey technology, etc./Development of the reservoir fluctuation survey method (Summary). Theme 3. Development of the electric/electromagnetic survey method; 1998 nendo chinetsu tansa gijutsu nado kensho chosa choryuso hendo tansaho kaihatsu hokokusho (yoyaku). 3. Denki denjiki tansaho kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Three observation wells were drilled in the Ogiri experimental field. The depth of drilling was 101-120m. In the self-potential observation, admitted were fluctuations, etc. caused by daily changes (tidal changes and earth current), earth current by external magnetic field induction, well drilling noise and injection well. In the resistivity structure survey, the whole area indicated a three-layer (high/low/high) structure, and the shallow high-resistivity layer was correspondent with the new unaltered volcanic rock, and the medium-depth low-resistivity layer with the clayey alteration. On the assumption that the reservoir model is improved by properties of geothermal water and 35% of the returning geothermal water goes back to the production region, pressure/chlorine concentration were satisfactorily explained. Changes in chlorine concentration by the returning geothermal water are estimated at 22% within production reservoir and at 52% in injection region, and when considering temperature changes, it was predicted that fluctuations of the resistivity underground are within 20%. The accuracy of the MT method was studied by using the MT method with the existing MT method. The accuracy was not enough to detect a resistivity of 10%, and therefore, the repeated measurement by fixed electrode or the continued MT method monitoring is needed. (NEDO)

  12. Achievement report for fiscal 1996 on the research and development of technologies for important region. Development of control system technology for combustion with energy use rationalized, etc.; 1996 nendo juyo chiiki gijutsu kenkyu kaihatsu seika hokokusho. Energy shiyo gorika nensho nado seigyo system gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The goal is to develop basic technologies to build an SiC device capable of service amid high-temperature surroundings for the advancement and optimization of combustion control systems. In an SiC semiconductor, the Si-C bond is broken when irradiated with ions, and this makes the occurrence of thermal oxidation easy to occur. In the study to form SiC into single-crystal substrates, a substrate with warpage of 10 micrometers or less and surface coarseness of 10 nanometers or less is realized. In the development of sensor technologies, the high-speed CVD (chemical vapor deposition) method is applied for the growth of crystals further on a 3C-SiC layer epitaxially grown by MBE (molecular beam epitaxy) surface control, which improves on layer characteristics. Element technologies are developed for the construction of a 3-terminal element (FET: field effect transistor), which is for the construction of a high-temperature, high-speed SiC device. An effort is made at achieving 3C-SiC hetero-epitaxial growth, etc., on a 3-inch Si substrate using an SiC crystal film formation experimenting apparatus, which aims at constructing a control device. Concerning the combustion control system, the relations between the air/fuel ratio and the emission spectra of radicals OH, CH, and C2 in a flame are made clear. Also referred to are the basic studies being conducted at research institutes such as universities and a survey of technological trends abroad.

  13. Report on the surveys in fiscal 1999 on the long term energy technology strategy investigations. Investigations on foundations to establish industrial technology strategies (Structuring of emphasizing strategies and the circulation type economic society harmonizing with environment); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (jutenka senryaku (kankyo to chowashita junkangata keizai shakai no kochiku))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper is a survey report for fiscal 1999 on structuring of the circulation type economic society harmonizing with environment. In order for Japan in the 21st century to solve various problems while maintaining sustainable development of the industries and economy, structuring the industrial technology strategies is indispensable. In order to establish targets to structure the circulation type society harmonizing with environment, small targets were broken down and specific technological examples were extracted as seen from categories based on flows of goods and the policy aspects. Then, from the viewpoints of extrication from wastes, reduction of risks caused by harmful substances, and growth under suppression of the global warming, case studies were performed on policy aspects toward the year 2010. Based on these studies, images of the emphasizing strategies were prepared, that are built on three pillars of 'R', the reduction, reuse and recycling. Specific technological examples were extracted comprehensively and specifically from research and development themes in research institutions inside and outside Japan to prepare a fundamental material for establishing the small targets. Furthermore, the examples were classified from the aspects of the three Rs. Areas of technological development seeds and areas with fewer seeds were made clear successfully. (NEDO)

  14. FY 2000 report on the verification survey of geothermal exploration technology, etc. Development of the reservoir fluctuation exploration method - Phase 2 (Feasibility survey); 2000 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. Choryuso hendo tansaho kaihatsu phase 2 F/S chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of developing the technology to grasp the behavior of geothermal fluids flowing inside the deep-seated reservoir, study of subjects was made for the reservoir fluctuation exploration method - Phase 2. In the overview of the reservoir fluctuation exploration method - Phase 1, various element technologies being developed in Phase 1 were arranged in terms of the overview of technology, results concretely obtained, present subjects, achievement of technical development, etc. In the overview of geothermal fields, domestic geothermal fields and overseas geothermal fields were outlined of which demonstrative tests in Phase 2 can be made. In the survey, data on characteristics of reservoirs at the sites proposed, existing data usable for the project and information of the existing facilities were covered in terms of the those that can be collected being based on the public data. In the study of demonstrative testing fields, to make selection of demonstrative testing fields in Phase 2, selection of conditions was made from the two points of view: 'necessary conditions for demonstrative testing field' and 'comparison in adaptability of geothermal fields by method.' (NEDO)

  15. Achievement report for fiscal 1997 on joint research to develop fuel cell technologies for urban energy centers. Research on evaluating life of phosphoric acid fuel cells; 1997 nendo toshi energy center nado nenryo denchi gijutsu kaihatsu kyodo kenkyu seika hokokusho. Rinsangata nenryo denchi jumyo hyoka kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    This paper discusses life evaluation on phosphoric acid fuel cells of urban energy center type for regional energy supply and on-site type to be installed in buildings. Operation characteristics tests and disassembly checks allow to identify factors for voltage decrease, and estimate the life therefrom particularly if the voltage decrease is caused from catalyst activity. The time before 10% decrease value is reached is now about 40,000 hours. The creep analysis method that has been developed recently can predict deformation in full-size reformers nearly exactly, and is effective in operating the reformer and evaluating the life at the design stage. Creep buckling is the critical value, which is caused by ecliptic deformation of internal tubes in the second catalyst layer. In a heat exchanger for fuel gas preheating, carbon in the reformed gas is carbonized and deposited due to catalytic action of nickel in the brazing material that bonds plates and fins in the heat exchanger. Iron also has a possibility of performing catalytic action. In the on-site type 1,000-kW class fuel cells, no structural problems have been presented even after the operation has been stopped. In order to extend time interval between phosphoric acid supply into the cells, it is necessary to reduce difference in the remaining phosphoric acid amounts in the stack lamination direction and in the cell flat surface. (NEDO)

  16. Project in fiscal 2000 of developing international standards for supporting new industries. Standardization of communication interface for open robots in production system; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Seisan system nado ni okeru open robot yo tsushin interface no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to realize the open use between robot controllers and personal computers on the communication level, R and D has been performed on the standard API required for structuring the applications to use robot information on the personal computers. A draft of the international standard was prepared. This paper summarizes the achievements in fiscal 2000. The current fiscal year has executed improvements on the standard API software, as well as the demonstration tests. The following achievements were obtained: problems in practical use based on the demonstration tests of RAO ver. 0.5 were extracted and rectified; the standard API (Ver0.9) given additional functions including file transfer was developed; the specifications for the standard API (Ver1.0) were compiled based on the result of discussions on the major application functions; as a result of the demonstration test on reliability of the standard API (Ver0.9), performances were verified when the API is connected under different structural and using conditions; and a resolution was made at the ISO/TC184/SC2 international conference that 'continuation is encouraged on the present R and D expected as a proposal for the new work items'. (NEDO)

  17. FY 1999 project on the development of new industry support type international standards. Standardization of a method to evaluate the performance of open robot use communication interface in production system, etc.; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Seisan system nado ni okeru open robot yo tsushin interface no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of standardizing the communication interface system between personal computers and robots, the R and D were conducted on ORiN (Open Robot Interface for the Network), and the FY 1999 results were summed up. ORiN is composed of the provider part, kernel part and application logic part. The provider absorbs differences in expression and protocols of robot controller data of each company and conveys them to the kernel part. The kernel part is composed of RAO and RDF. RAO adopts the disperse object model DCOM technology and supplies the network transparency and common access method to robot. RDF supplies files with expansion of robot structure models using XML. By this, ORiN was made adoptable for future, permitting differences in each robot. In the International Robot Exhibition held in October 26-29, 1999, the prototype of ORiN was jointly demonstrated by each company. (NEDO)

  18. Survey report for fiscal 1998. International project for rationalizing energy use (a project for investigating analyzing a tool to improve energy consumption efficiency in Asia) (Data collection 1 (Year 1990 data)); 1998 nendo kokusai energy shiyo gorika nado taisaku jigyo chosa hokokusho. Asia energy shohi koritsuka bunseki tool chosa jigyo (shiryoshu 1 1990 nen data)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With an objective to identify quantitatively the mutually influencing effect of economical development and energy consumption efficiency improvement in the entire Asia-Pacific region, a data collection was prepared according to the common industry classification as a tool to analyze energy consumption improvement in Asia. This data collection summarizes the industry relation tables and the energy relation tables available in eight Asian countries (Korea, Indonesia, Thailand, Philippines, China, Taiwan, Singapore and Malaysia) and Japan. Both kinds of the tables are unified in conception among the nations, hence comparable. The industry relation table consists of a basic transaction table, a charged coefficient table, a final demand converter table, an import coefficient table, a reverse matrix table, a sensitivity coefficient able, an influence force coefficient table, a production inducing amount table, a production inducing coefficient table, a production induction dependence table, an import inducing amount table, an import induction coefficient table, and an import induction dependence table. The energy table consists of an energy input table, an energy consumption table, and an emission table. (NEDO)

  19. Fiscal 1997 research report on development of use technology of bio-resources such as complex biosystem (Development of use and production technologies of complex biosystems); 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho (fukugo seibutsukei riyo seisan gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This report summarizes the fiscal 1997 research results on production technology of functional materials, and the research study result for utilizing substance production and decomposition by complex biosystem for industries. For detecting technique of microorganisms in soil, staining by CFDA-AM was suitable, and allowed visualization of sulfate- reducing bacteria during culture. For research on functional analysis technology, study was made on atomic force microscope technology to detect microorganisms in environment and observe their fine structures. For research on detection, separation and cultivation technology of difficult-to-culture microorganisms, a molecular genetic analysis method of microbial communities and a determination method of their viability were selected. For functional substance production technology, study was made on technical utilization of bioflocculant produced by microbial consortia as environment-friendly oil removal reagent, and on gene transfer control in microbial consortia. For the research study for the project, survey was made on useful substances produced by complex biosystem. (NEDO)

  20. Report on the FY 1999 survey on long-term energy technology strategy/basic survey for working out industrial technology strategy. Technology strategy by field (formed raw material field); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (sokeizai bun'ya))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper described the results of the survey of the formed raw material field in relation to the FY 1999 long-term energy technology strategy. In the advancing international specialization, efforts are being made for the secure basic base technology force and cost reduction required for competition, and at the same time the aim is not to retain/improve all the formed raw material technologies, but to discriminate the materials in the aspects except the cost. By promoting the reformation into the proposed type industry, it is necessary to work out the bold strategy including the review of the system/structure for promoting the strategic technology innovation by aiming at the important formed raw material technology which can be a life line for the assembly industry, in particular. Concretely, the comprehensive technology system which concentrated a variety of engineering knowledge/information was constructed. The system is shifted to the one that adopted information/communication technology. The conversion in the early time to the proposed type industry is attempted. Japan acquires capability for heightening the level of technology, by which Japan will continue leading the formed raw material technology to the world's top level. Japan realizes the network consisting of the industry, university and government. The environment is realized where new personnel will naturally enter the formed raw material industry and bottom up the total technology force. (NEDO)

  1. FY 1996 report on the results of the development of superconductor power application technology. Study of a total system, etc. (Investigational study of the introductory effect); 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. Total system nado no kenkyu (donyu koka no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Under the secondary interim assessment made in FY 1995 between the assessment committee of the energy/environment technology development sectional meeting of the Industrial Technology Deliberation Council and NEDO, in this project, the following were conducted in FY 1996: study of trial manufacture of superconductor motor model machine and R and D of element technology (conductor technology/refrigerator technology). The study was proceeded mainly with Super-GM, and as to the motor, the preparation for test on a part of the model machines was finished. Considering FY 1998 which is the final year of this project, the investigational study in FY 1996 aims at accumulating/arranging/analyzing the data which help judge how to proceed with the future R and D of superconductor power application technology continuously based on the secondary interim assessment. For superconductor motor and various superconductor power appliance, economical/technical feasibilities and methods of R and D and surveys of trends in Japan and abroad for the R and D were made important items. Further, 'R and D of the basement of superconductor power application' proposed in the secondary interim assessment (R and D of the combination of elements which become the basement of equipment technology over a stage of parallel R and D of element technology of conductor, etc.) targeted the presentation of concrete details. (NEDO)

  2. Fiscal 1998 New Sunshine Project research report. Development of separation technology of hetero-compounds from coal-derived oil, and use methods of them; 1998 nendo sekitan ekikayuchu no tetero kagobutsu nado no bunri gijutsu to yoto no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project develops the efficient separation technology of compounds including hetero-atoms such as O and N from coal- derived oil, and researches effective use methods of them. Study is made on the concrete applications and problems of the following separation technologies of hetero-compounds: Distillation/refrigeration, extraction, supercritical gas extraction, pressurized crystallization, crystallization, adsorption, and membrane separation technologies. Based on the study result, the applicability of such various separation technologies of hetero-compounds from coal-derived oil fractions is confirmed experimentally. By using the newly developed bench-scale test equipment of an optimum separation process, the process performance is confirmed, and various engineering data are collected. Study is also made on the effective use method of the hetero-compounds separated by the above equipment. In fiscal 1998, as the electric membrane dialysis experiment result on phenolates derived from phenols in Kashima pilot naphtha and atmospheric light oil, the existence of substances (Ca, Fe, SO{sub 4}) deteriorating membranes was confirmed. Preventive measures against contamination of these bivalent cations and anions are one of future issues. (NEDO)

  3. FY 2000 Report on technological trend surveys. Surveys regarding construction of the co-production techniques for substance and electric power; 2000 nendo gijutsu doko nado chosa hokokusho. Busshitsu to denryoku heisan ni yoru co-production gijutsu no kochiku ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This project is aimed at surveys on the elementary and peripheral techniques necessary to construct the systems, with the objective to draw the conceptual designs of the total system for co-production of a substance and electric power. In a general reaction process, substances are produced under an advantageous condition that is dependent on reaction rate and equilibrium, where most of the energy is dissipated in the form of sensible and latent heat without being used for the chemical reaction. The co-production system under consideration uses high temperature of 500 degrees C or higher exhausted from a power station or industrial unit to produce macromolecules or synthesis gases, wherein the exothermic reaction increases temperature of the heat source, which is recovered in the form of steam for driving the steam turbine to produce electric power. On the other hand, low-temperature waste heat of around 150 degrees C is converted into a liquid fuel or other value-added products by the liquid phase pressurized system. The elementary techniques to construct these processes are surveyed, and the thermal processes are analyzed. The investigated items include substance production processes, electric power production processes and total systems. (NEDO)

  4. FY 2000 report on the survey of policies on cooperation in new energy/energy conservation for developing countries by developed countries/international organizations. Survey of collection/analysis of information on effective energy utilization, etc.; 2000 nendo senshinkoku kokusai kikan no tai tojokoku shin energy sho energy kyoryoku seisaku ni kakawaru chosa hokokusho. Energy yuko riyo nado joho shushu bunseki chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Looking for measures for cooperation in effective energy conservation for developing countries, the paper arranged characteristics of the policies, systems and organizations in relation to energy conservation/new energy policies in developed countries and international organizations excluding Japan. Concretely, survey was made of the following 5 fields: 1) new energy cooperation (project) for developing countries by developed countries and international organizations excluding Japan; 2) outline of activities by aid giving organizations; 3) energy conservation policies of developing countries and cooperation of developed countries and international organizations; 4) policies of new energy introduction in developed countries; 5) study to reinforce cooperation for helping developing countries by Japan and developed countries/international organizations excluding Japan. In 1), survey is composed of case study of the main project and study of the outline of activities by aid giving organizations. The activities by the following aid giving organizations were surveyed: the World Bank group, International Finance Corporation (IFC), United Nations Development Program (UNDP), the European Committee and the Asian Development Bank (ADB). (NEDO)

  5. FY 2000 report on the survey on the long-term energy technology strategy, etc. - Basement technology for implementation of industrial technology strategy. Survey on the extraction of preferential important technical subjects in FY 2002; 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho - sangyo gijutsu senryaku sakutei kiban chosa. 2002 nendo yusenteki juyo gijutsu kadai no chushutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This survey is to investigate the consciousness of researchers and engineers of enterprises, universities, etc, of the importance of about 100 important technical subjects in 'the industrial technology strategy' prepared by the Ministry of Economy, Trade and Industry. In the questionnaire survey, the following were selected: 1)systematization of policy in consideration of the social needs and R and D of the technology to realize it; 2) R and D of the technology to advance the future frontier; 3) technical subjects that the government should promptly start to tackle in each classification in arrangement of the intellectual basis. Answers to the following items were obtained: 'selection reasons' for why it was considered important in each technical subject, 'lead time' toward the time of the industrialization, 'international positioning' of Japan against Western countries, 'possibility of heightening/maintaining the international competitive force,' and 'items that the government should participate in.' In 1), the following four big targets were arranged: 'security/safety,' 'informatization,' 'environment' and 'energy'. In 2), the following technical subjects were arranged: 'biotechnology,' 'information communication technology,' 'production technology,' 'materials/process technology,' 'energy/environment' and 'new blending/traversable/integrated technology.' In the results of the survey, analyzed were big targets, and trends and characteristics at technical field levels. (NEDO)

  6. Fiscal 1999 research and verification of geothermal energy exploring technologies and the like. Development of reservoir mass and heat flow characterization (Electrical and electromagnetic monitoring technology - Summary); 1999 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho (yoyaku). Choryuso hendo tansaho kaihatsu (denki denjiki tansaho kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Facilities for monitoring self-potential and resistivity are installed in the Ogiri district, Kagoshima Prefecture, where the Ogiri geothermal power plant is situated, and studies are made about relations between hot water production/reinjection and potential/resistivity at the power plant for the development of a high-performance numerical simulation system for the reservoir. The activities cover the development of (1) a self-potential monitoring system, (2) the development of a resistivity monitoring system, and (3) the development of a reservoir change prediction technique using self-potential and resistivity. Under item (1), eight self-potential monitoring stations are newly installed for the monitoring effort to continue now at a total of 50 stations. Potential has risen by 20 mV in two years since the drilling of a production replenishment well in February of 1999, with the domain of change in potential also expanding. Under item (2), the 3D MT (3-dimensional magnetotelluric) technique is used for resistivity profile investigation at 80 monitoring stations and preliminary monitoring tests are conducted to deliberate positions for resistivity monitoring. Under item (3), tracer tests are conducted for constructing a high-precision reservoir model for predicting changes in temperature, etc., attributable to the return of reinjected hot water, and a natural state reservoir simulation model is fabricated. (NEDO)

  7. FY 1998 report on the waste processing/recycling related technology, 'The R and D of lead-free solder standardization'; 1998 nendo haikibutsu shori recycle kanren gijutsu seika hokokusho. Namari free handa kikakuka nado kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    To reduce the environmental pollution caused by lead eluted from the electronic equipment waste, the R and D on lead-free solder were conducted and the results were summarized. As to the basic characteristics, the evaluation test method was studied in terms of the range of melting temperature, mechanical strength, wettability and joint strength, to select a uniform test method. As the lead-free solder, Sn-Ag alloys were mainly used and mixed in a combination of Cu, Bi and In. Changes in characteristics were made clear by adding trace elements such as Ge, Mn and P. Relating to the applied characteristics, in selection of solder materials, materials were selected for which evaluation of the commercialization is proceeded with from a viewpoint of promotion of commercialization. Concerning the experimental evaluation of characteristics of lead-free solder in mounted substrates, it was indicated that basically lead-free solder can be practically used. Further, it was indicated that the Sn-Ag-Cu-Bi system depends not on solder composition but on active force, printing accuracy and flux characteristic of solder paste, that improvement of solder paste has an effect on mounting characteristics. (NEDO)

  8. Fiscal 1999 survey report on survey of long-term strategy on energy technology. Long-term energy technological strategy survey (Long-term energy technological strategy survey); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Choki energy gijutsu senryaku chosa (choki energy gijutsu senryaku chosa))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    To enhance still more effectively the research and development of energy-related/environmental technologies, research and development strategies have to be worked out from a long-term view point and policy resources such as investment in research and development should be optimally distributed after clarifying and defining the course to follow toward the achievement of research and development goals. This project aims to conduct studies, and to show the course to follow in the future, towards the establishment of a long-term energy technological strategy by investigating energy systems for around 2050, interim energy systems at the intermediate stage, and innovative energy technologies for realizing such energy systems. In Chapter 1, the position of the survey and its purpose and prerequisites are shown. In Chapter 2, the history of social and economic conditions surrounding energy/environmental technologies and of energy situation up to the present time is compiled, and the outlook is analyzed and predicted. In Chapter 3, formulation of a long-term energy technological strategy is discussed. In Chapter 5, how to embody such a strategy is shown. (NEDO)

  9. Fiscal 1999 achievement report. Development of technology for machine tool with energy consumption rationalized (Research and development of environment-conscious grinding system); 1999 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Kankyo taiogata kensaku kako system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A large quantity of coolant is used in the grinding process for ensuring high accuracy and quality in the work. This presents a serious problem from the viewpoint of environmental impact or energy conservation, and now environment-conscious grinding methods requiring no or less coolant are sought for. With a view to answering the demand, efforts are exerted to put to practical use, and improve, an EcoloG grinding technique. The goal is to reduce to half the energy that the grinding process is now consuming. The EcoloG technique is a grinding method under which vegetable oil mist is cooled for lubrication and a small amount of cooling water is fed to the point of grinding for removing chips. In fiscal 1999, a survey was conducted on technical literature, patents, and the like in and out of Japan for the study of the actual state of dry machining, and then the course of future studies was clearly established. Studies were also carried out aiming at the practical application and improvement of the EcoloG grinding technique, and the technique achieved a quality level as high as that of the conventional coolant-aided method in a process of grinding a shaft to have an accurate outer diameter by use of an ordinary wheel head. (NEDO)

  10. General report on the results of the development of fuel cell technology such as urban energy center. Evaluation study of life of phosphoric acid fuel cells (fiscal 1995 and 1996); Toshi energy center nado nenryo denchi gijutsu kaihatsu kenkyu seika sogo hokokusho. Rinsangata nenryo denchi jumyo hyoka kenkyu (1995 kara 1996 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Receiving subsidies from MITI, NEDO carried out this project in fiscal 1995 and 1996 as a joint research with Technology Research Association for Phosphoric Acid Fuel Cell Power Generation System and others. The project aimed at developing the accelerated test method which can evaluate in a short time the cell life of phosphoric acid fuel cells (PAFC) and the lowering of characteristics. The accelerated test method of PAFC life is thought to be a tool indispensable for the promotion of commercialization, but the accelerated test method like the usual material evaluation has not yet been established. To solve this problem, procedures were developed to rationally plan the accelerated test on short stacks of full scale based on the small cell test data. Here, to rationally estimate the operational state under actual conditions based on the data on the accelerated test, it is necessary to fully understand the mechanism of deterioration of PAFC. By conducting in parallel the element study for the basic elucidation of cell deterioration phenomena, obtained was the useful information/knowledge which back up the results of the accelerated test scientifically. 168 figs., 33 tabs.

  11. FY 1999 Industrial science and technology research and development project. Report on the results of research and development of the technologies for genome informatics (Acceleration of analysis of green mold transcription control information); 1999 nendo genome infomatics gijutsu kenkyu kaihatsu seika hokokusho. Koji kabi no tensha seigyo joho no kaiseki kasokuka nado

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A total of 49 budding yeast transcription factor disruptants and one conditional transcription over expression strain are produced, to elucidate the gene regulation networks using the gene expression profile data, and to measure the systematic and high-quality gene expression profiles using the Affymetrix's GeneChip system. The program is also developed for accurately predicting the base sequences which regulate expression of given gene groups, based on the uniqueness of the upstream sequences. The analysis with the aid of the program predicts 8 gene expression regulation sequences, which are considered to be novel, from the gene groups of retarded expression by the transcription factor disruptants. The time course gene expression data are produced from the transcription factor SW14 conditional over expression strain. The analysis of the data indicates that the analysis of the subtracted genes using the gene expression profiles from the wild type strain is useful for clarifying the effects of the derived transcription factor over expression. (NEDO)

  12. FY 1999 Report on research and development of energy utilization rationalization superhigh-technological liquid crystal technologies. Superhigh-technological electronic technology development promotion project for new functional electronic material design, control and analysis technologies; 1999 nendo energy shiyo gorika chosentan ekisho gijutsu kaihatsu seika hokokusho. Chosentan denshi gijutsu kaihatsu sokushin jigyo shinkino denshi zairyo sekkei seigyo bunseki nado gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-04-01

    Described herein are the FY 1999 results of the liquid crystal technology development project. For the researches on multi-layer reflection, composite panels of flattened resins of different refractive index are developed to improve 2-layer monochromic contrast ratio. The guest/host liquid crystal compositions of high orientation order are investigated as the those useful for high contrast. Compounds are pursued for superanisotropic light absorption, and modification with a substituent is found to be effective. Molecular orientation controlling is also studied. For researches on memory-sustaining type liquid crystals, the studied items include formation of thin ferroelectric films on glass substrates, improvement of voltage-sustaining characteristics by composites (including compounds), and doping of trace quantities of ionic impurities. For development of image element colors, the studied items include multi-lattice-structured, oriented HPDLC devices, composites of high birefringence (high order light scattering), and light interference, high order light scattering type light control devices. The multi-dimensionally anisotropic structure of configuration divided into 3 parts of R, G and B is developed to create directive reflection which improves brightness of the reflection type color liquid crystal. A group of compounds are pursued to develop liquid crystal compositions of high refractive index anisotropy, and promising ones are found. The results of the comprehensive investigations are also described. (NEDO)

  13. FY 1997 R/D project of industrial and scientific technologies contracted with NEDO. Report on technology development of utilization of biological resources such as bioconsortia (development of analytical techniques of bioconsortia); 1997 nendo sangyo gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu (fukugo seibutsukei kaiseki gijutsu no kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Bioconsortia are microbial composites composing of more than two kinds of microorganisms with special functions. To utilize their advanced functions, some techniques have been developed for analyzing their functions and interactions, and for identification, separation and incubation of the constituent microbial groups. In FY 1997, an investigation was made on technology trends, domestic researchers, and research topics related to bioconsortia. To manage and promote the progress of research at the National Institute of Bioscience and Human-Technology where the centralized management of this project is conducted, meetings are held once a month to examine the progress at the institute, in which reports are made and discussions are held on how each research item is progressing. In addition, meetings of the committee to promote research are held every other month to consider and examine measures required for promoting the research. Re-entrustment of research has been made on two subjects, i.e., `Studies on biological significance of symbiotic microorganisms` by Prof. Ishikawa of the University of Tokyo, and `Study on the relationship between the biosynthesis of useful terpenic materials of plant origin and the differentiation of plant tissues, and their effective production by plant cell cultures` by Prof. Inoue of Gifu Pharmaceutical University. 27 refs., 13 figs., 1 tab.

  14. Report on investigations in fiscal 2000 on the basic investigation on promotion of joint implementation. Rehabilitation of gas turbine power plants owned by Myanmar Electric Power Enterprise (MEPE); 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. MEPE/gas turbine hatsudensho rihabiri

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Myanmar generates majority of the whole electric power by using thermal power plants consisting of single gas turbines, and gas and steam composite turbines. However, because of chronic power shortage and fund unavailability, the major gas turbines are being operated in quite inadequate environment. As a result, reduction in power generation efficiency has become manifest due to aged deterioration, increasing the quantity of CO2 emission. The present project is, in order to link it to the 'Clean Development Mechanism' being carried out with developing countries, and placing Tharkayta Power Plant as the object, intended to comprehensively discuss a rehabilitation program to renew the existing gas turbines with advanced ones, in relation with feasibility of the project implementation including the effect of CO2 emission reduction, profitability, and proliferation effects. A prospect was acquired that, by replacing the gas turbines alone with 25-MW class gas turbines, the plant output will increase to 97.2 MW (78.5 MW in the existing facilities) and the plant efficiency to 43.3% (36.5% in the existing facilities). The energy saving effect during a period of 40 years would be 708,000 (toe) as heat consumption converted to crude oil, and the CO2 emission reducing effect would be 2,160,000 (t-CO2), respectively. (NEDO)

  15. FY 2000 report on the basic survey to promote Joint Implementation, etc. Survey of the effective use of wastes at palm oil refineries; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Palm oil seisei kojo ni okeru haikibutsu yuko riyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As to empty fruit bunches (EFB) which are wasted at the Lahad Datu plant of Felda Vegetable Oil Products Co. in Malaysia, a project was studied for energy substitution and greenhouse effect gas reduction by fluidized bed cogeneration facilities using this as fuel. In the project, studied was the introduction of on-site cogenerator of 7,800kW in generating-end output, and that of IPP cogenerator of 16,000kW as reference. As a result of the study, the energy substitution amount in toe in 20 years was approximately 376 k tons in case of on-site power generation/fluidized bed boiler and approximately 695 k tons in case of IPP and fluidized bed boiler. The amount of greenhouse effect gas emission in toe in 20 years was approximately 5,757 k tons and 11,654 k tons, respectively. Concerning the profitability, the internal earning rate was 3.32-8.47% in case of on-site power generation/fluidized bed boiler and 9.13-14.65% in case of IPP/fluidized bed boiler. It indicated the materialization of the project. (NEDO)

  16. Report on achievements in proliferation project to assist introduction of environment harmonizing type coal utilization system in fiscal 1998. Joint demonstration project for CMG recovery and utilization system in fiscal 1998 (utilization facilities); Kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo seika hokokusho. 1998 nendo CMG kaishu riyo system kyodo jissho jigyo (riyo setsubi)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    This paper describes the achievements of the discussions in fiscal 1998 on the utilization facilities related to the coal bed methane gas supply plan for the city of Tieling in China. The gas quality standard calls for 3,500 kcal/m{sup 3} or more (methane concentration of 41% or higher). The supply is planned to start in December 1999, and continue the supply of 141,000 Nm{sup 3}/day in 2000, and 212,000 Nm{sup 3}/day in 2001 and thereafter. A gas supply center to collect gases recovered from each mine will be installed in the vicinity of the existing gas holder located about 2 km east of the Tiefa Mining Bureau. The Japanese side bears the cost of installing a gas compression and transportation facility for gas supply to the city of Tieling, a monitoring system, and devices for comprehensive surveillance system. This paper shows the overall plan drawings, the drain separator room building plan, the plans for arranging devices in the machine room, and the piping scheme. In addition, the piping plan around the gas holder, and the basic device plan are shown. Also appearing in the paper are the machine summary drawings, summarized flow charts, gas holder plan, de-humidifier plan, and electricity and instrumentation plans. The main body and supporting structure for the gas holder, and the foundation strength calculation sheets are also shown. Descriptions are given also on the facilities to deal with variation in demand quantity and supply quantity. (NEDO)

  17. Fiscal 2000 research achievement report on the development of super-advanced liquid crystal technology for energy use rationalization. Development promotion project for super-advanced electronic technology - Design, control, analysis, etc., of electronic materials having novel functions; 2000 nendo energy shiyo gorika chosentan ekisho gijutsu kaihatsu seika hokokusho. Chosentan denshi gijutsu kaihatsu sokushin jigyo (shinkino denshi zairyo sekkei seigyo bunseki nado gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-04-01

    Efforts are focused on the verification of target devices under the respective subjects, and activities are conducted with the development system reinforced. Three newly proposed reflection type liquid crystal devices achieve the target specifications of a reflection factor of 60% or higher and a contrast ratio of 15:1 or higher. Studies are conducted involving the five fields of (1) multilayer reflection devices, (2) memory retention liquid crystal devices, (3) single pixel color devices, (4) directional reflection devices, and (5) joint research. Research and development in field (1) covers ultra-anisotropic optical materials, ultrahigh reliability host liquid crystal materials for guest-host liquid crystals - mixed system, low voltage driven/high load holding liquid crystal compound systems, and new liquid crystal molecule orientation control technology; in field (2), low temperature fabrication of ferroelectric thin film, and ultrahigh purity high reliability liquid crystal compounds; in field (3), materials capable of controlling optical interference and higher order light scattering, photoregulation devices, highly birefringent liquid crystal materials - mixed system, and ultrahigh efficiency light scattering liquid crystal compounds; and, in field (4), multi-dimensional anisotropic structure fabrication technology and ultra-anisotropic optical materials. (NEDO)

  18. FY 2000 report on the survey of long-term energy technology strategy, etc. - Fundamental survey to work out the industrial technology strategy. Research survey on technology innovation indices to be worked out; 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (gijutsu kakushin shihyo no sakutei ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For technology innovation, it is indispensable to arrange the environment where the continuous and spontaneous technology innovations are generated. >From this point of view, the paper re-confirmed functions of enterprises, universities and national research institutes that are main bodies of technology innovation. For the use for working out measures for activation as the basic data, conducted were the making of indices for surveying the whole system of technology innovation in Japan, and the study of the data to be prepared as statistics and the survey method. In the 1st stage, about 450 figure/table data related to technology innovation were collected for making them database from official statistic data and publications of governments and international organizations in Japan and European countries. Further, using official statistic data, about 240 figure/tables were made which seem to be important as indices of technology innovation. In the 2nd stage, on the basis of this database, the details of the activities were analyzed, and from the indices, the actual situation/subjects were considered. At last, the paper explained the index system of 'Oslo Manual' which is a guideline of working out OECD's innovation indices. (NEDO)

  19. Basic investigation on promotion of joint implementation in fiscal 2000. Energy saving projects at two steel making companies in Fushun City in China; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Chugoku Fushun shi ni okeru tekko gaisha 2 sha no shoene project chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective of saving energy and reducing greenhouse gas emission, investigations and discussions were given on two steel making companies in China. Discussions were given for Fushun Special Steel Co., Ltd. on abolishment and unification of four electric furnaces into two new electric furnaces, and for Fushun New Steel Co., Ltd. on installation of a granulation reinforcing facility, a segregation reinforcing device, and cooler waste heat recovery boilers for the sintering machine, installation of sensors including the waste gas oxygen concentration meter, adoption of a process computer, and optimization of the furnace temperature patterns for the heating furnace. As a result of the discussions, it was revealed that the unit requirement for electric power used at Fushun Special Steel can be reduced largely, and so can the fuel used at Fushun New Steel. The annual energy saving effect would be about 500 million yen relative to the investment amount of 2.8 billion yen at Fushun Special Steel, and about 400 million yen relative to the investment amount of about 400 million yen at Fushun New Steel. The greenhouse gas emission would be reduced annually by 40,000 t-CO2 and 60,000 t-CO2 respectively. Fushun Special Steel will execute an international bid in May this year. (NEDO)

  20. FY 2000 report on the basic survey to promote Joint Implementation, etc. Project for the modernization of general industry use boilers at the industrial complex in Namping City, Fujian Province, China; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Chugoku Fukkensho Namping shi danchi no ippan sangyoyo boiler kindaika jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    An investigational study was conducted of the project for energy conservation and greenhouse effect gas reduction by introducing the energy utilization system combined with CCS equipment and cogeneration system to general industry plants at the industrial complex in Namping City, Fujian Province, China. As a result of the field survey, it was concluded that the capacity suitable for CCS center was 200,000 t/y and the size suitable for pulverized coal boiler at each site was 35 t/h. The energy conservation amount in this project was the coal use reduction amount by 88,000 t/y (48,000 toe/y), and the greenhouse effect gas reduction amount was approximately 90,000 t-CO2/y. As to the economical efficiency of the project, the period of ROI was about 5.1 years, and the internal earning rate at each site was 14-23%. The materialization of the project was confirmed. However, in the case of raising the required funds from city banks in China, financing conditions are strict, and the financing seems to be difficult at each site. It is necessary to raise low-interest funds such as the special environment yen credit. (NEDO)

  1. Fiscal 1997 report on the survey of verification of geothermal exploration technology, etc. 1. Development of the reservoir variation exploration method (development of the fracture hydraulic exploration method); 1997 nendo chinetsu tansa gijutsu nado kensho chosa. Choryuso hendo tansaho kaihatsu (danretsu suiri tansaho kaihatsu) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described the fiscal 1997 result of the fracture hydraulic exploration method as the variation exploration method of geothermal reservoirs. By elucidating hydraulic characteristics of the fracture system forming reservoir, technologies are established which are effective for the reservoir evaluation in early stages of development, maintenance of stable power after operational start-up, and extraction of peripheral reservoirs. As for the pressure transient test method, a test supporting system was basically designed to obtain high accuracy hydraulic parameters. As to the tiltmeter fracture monitoring method, a simulation was made for distribution of active fractures and evaluation of hydraulic constants without drilling wells. In relation to the two-phase flow measuring method, for stable steam production, the use of the orifice plate, the existing flow measuring method, etc. was forecast as a simple measuring method of the two-phase state of reservoir. Concerning the hydrophone VSP method, a feasibility study was made of the practical VSP for high temperature which can analyze hydraulic characteristics and geological structures around the well at the same time which the existing methods were unable to grasp, and brought the results. Moreover, to make high accuracy reservoir modeling possible, Doppler borehole televiewer was made in each reservoir. 80 refs., 147 figs., 22 tabs.

  2. FY 1998 report on the verification survey of geothermal survey technology, etc./Development of the reservoir fluctuation survey method (Summary). Theme 5-1. Technology to predict reservoir fluctuations; 1998 nendo chinetsu tansa gijutsu nado kensho chosa choryuso hendo tanhsaho kaihatsu hokokusho (yoyaku ). 5-1. Choryuso hendo (choryuso hendo yooku gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The existing gravity post processor was improved and a feasibility study of downhole gravity profile measurement was conducted. As compared with the earth surface, great fluctuations could be observed in the downhole, indicating a possibility of acquiring the useful information on underground steam zones. The existing self-potential post processor was improved, which made the history matching analysis easy. A geochemical post processor was developed which can analyze geochemical fluctuations. Changes in resistivity in reservoir associated with production/injection of geothermal fluids were calculated, and a feasibility was shown of developing the resistivity post processor into which the existing MT forward calculation method was efficiently integrated. From the data on effects of changes in temperature/fluid phase on seismic wave velocity and damping, usability of the seismic wave post processor was made clear. From the reservoir fluctuation analysis using gravity/self-potential post processor, it was found out that gravity fluctuations at Onikobe had already finished and presently there are less fluctuations. Self-potential is still in fluctuations and becomes indices of reservoir fluctuations. Study was made also on Sumikawa where steam is dominant. (NEDO)

  3. Fiscal 1997 report on the verification survey of geothermal exploration technology. 5-1. Development of the reservoir variation survey method (technology of prediction of reservoir variation); 1997 nendo chinetsu tansa gijutsu nado kensho chosa. Choryuso hendo tansaho kaihatsu (choryuso hendo yosoku gijutsu) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the reservoir evaluation at an initial developmental stage and stabilization/maintenance of power after the start of operation, the fiscal 1997 result was described of the study of technology of prediction of reservoir variation. Using the conventional post processor, feasibilities were computed of reservoir models and behavior after the development, and gravity/self potential/resistivity variation. Variation in the seismic wave speed structure was large in travel time change distribution. The measuring accuracy of 1m sec is required to get enough detection resolving power. A conceptual design of the post processor development was conducted to study a system operated on Windows. Based on the reservoir numerical simulation technology, by taking in variation parameters such as gravity and self potentials as new model constraint conditions, the reservoir modeling technology which increased in accuracy by history matching was trially developed. Using the conventional reservoir model in the Oguni area, predictably computed were reservoir behaviors during 50 years which simulated a 20 MW development. Effectiveness of the post processor were able to be shown though influenced by characteristics such as permeability and resistivity. 74 refs., 95 refs., 12 tabs.

  4. Fiscal 1997 Project related to research and development of global environment industrial technologies. Report on the results of works commissioned for research and development of technology for reducing carbon dioxide emissions; 1997 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu kanren jigyo. Nisanka tanso nado haishutsu teigen gijutsu kenkyu kaihatsu itaku gyomu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    With an objective of achieving reduction in emission of carbon dioxide and fluorocarbons, the `research and development on technologies to reduce emission of carbon dioxide and other substances` consisting of eight projects were conducted. In research and development of waste water treatment technologies using submerged combustion, studies were performed on removal by combustion of such pollutants as organic compounds, nitrogen compounds, and sulfur compounds. The development targets were achieved on each item. In research and development related with thermal electric power generation elements, semiconductor single crystals were fabricated in order to acquire technical knowledge on thermal power generation elements intended of utilizing industrial waste heat, whereas a simulation technology for designing was developed. In other projects, research and development works were carried out on high-performance heat insulating materials, and a movable methanol reformer for fuel cells. Developments were conducted on a large pressure reducing valve, and a cooling and heating turbo heat pump for regional air conditioning facilities. Research and development were made on Peltier elements, all efforts having achieved results respectively. 134 figs., 65 tabs.

  5. Survey on the long-term energy technology strategy. 2. Survey of the basement of the industrial technology strategy settlement (Environmental basement arrangement strategy); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa. 2. Sangyo gijutsu senryaku sakutei kiban chosa (kankyo kiban seibi senryaku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the Japanese industry to cope properly with the age of great competition and to secure the technology competitive force, it is indispensable to collect/analyze a lot of information and develop policies, that is, strategies, for industrial technology. For study of types of technology innovation system, a survey was conducted in FY 1999 of samples of products with comparatively high competitive force. Concept of the product concerned was examined in terms of the enterprise (person) which created the product, enterprise which commercialized it first in the world, etc. As to each of the technologies, factors to get a top share were analyzed. Based on the analyses, factors to get a large share were classified, and the relations with technology were analyzed. With 'Study of industrial technology strategy' issued in March 1999 as reference, 54 of the products of which the world share is more than 75% were extracted. In the table, about the items on creation of technology, technology was classified into the basic technology, similar technology, traditional technology, and combined technology. About the items on improvement/application, it was classified into improvement and usage development. The other items were classified into production technology, users, and development/production cooperation infrastructure. (NEDO)

  6. Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy). Machine industry technology field (Machine tool); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijjtsu senryaku) kikai sangyo gijutsu bun'ya (kosaku kikai bun'ya)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 basic research result on industrial technology strategy of a machine tool field. Corresponding to construction of an environment-friendly recycling economic society and economic growth as estimated change in social and industrial structure during 2010-2025, major themes are reuse of machine tools, energy saving, environment design, chip treatment and resource recovery. With preparation of information infrastructures in an advanced information society, major issues are 3D-CAD, remote diagnosis, remote control and self-restoration. Because of decline of the birth rate, positive employment of aged persons and women is desirable. New machining technology for new materials, and fusion of various machining technologies are important. For micro-technology, study should be made on the concept and effect of micro-factory (energy saving, space saving, cost reduction, higher accuracy and higher speed). For higher-accuracy machine tool, static, dynamic, thermal and movement characteristics are the key for improving the proper technology. For faster machining. fine basic structural element, faster main spindle and faster feed are important. (NEDO)

  7. Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy). Aerospace technology field (Aircraft technology field); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (kokuki gijutsu bun'ya))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 basic research result on industrial technology strategy of an aircraft technology field. In an aircraft field, since the major theme is application of new technologies to new airframe development, with joining in international cooperative development of aircraft, Japanese initiative development of airframes based on the domestic market demands and profitability should be started as early as possible. Because there is no airframe development by only one country including U.S.A., Japan is profitable to unite with some overseas companies, and invest selectively in specific leading fields. Positive technical support to safety, reliability, comfort and environment harmony are also important. More important theme than establishment of elementary technologies is preparation of an integrated flight demonstration system to expand application chances of development results, and preparation of various test facilities for tests required during development activities. Application of information technologies to the whole aircraft industry, and organic cooperation between the private and public sectors are also important. (NEDO)

  8. FY 1998 result report. Report on the results of the examinational research on the trend of technology development in the iron/steel industry; 1998 nendo seika hokokusho. Tekko sangyo no gijutsu kaihatsu doko nado ni kansuru chosa kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The trend of the technology development in the Japanese iron/steel industry was compared with those in foreign countries and surveyed to increase the international competitive strength. From the viewpoints of technology, industry and goods, the iron/steel field was characterized based on the statistic data, and especially automobile use steel materials were selected such as cold rolling high tension steel sheet, surface treated steel sheet, and bearing sheet. The analysis of factors of competitive superiority was conducted, and the following were presented: measures for process continuation, and measures taken from the age of equipment and cost indexes. The paper also surveyed the trend of pig iron making/steel making technology in Asia. The present international technical competitiveness in the iron/steel industry in Japan, especially of automobile use steel sheet, is very high. This is because of the well-functioned demand-oriented development, and also as a result of the mutually influentially conducted equipment development such as process continuation and development of new goods, supposing the iron/steel continuous process and reduction in impurities. However, fears are the stagnation in the recent technical development strength and the saturation of new equipment. Moreover, the further heightening is needed of the international cost competitive strength of general-purpose products. (NEDO)

  9. Research achievement report for fiscal 1998 on the development of high-performance industrial furnaces. Research and development of high-performance industrial furnaces and the like (2); 1998 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu (2)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Volume 2 named above contains part of research achievement reports and individual research achievement reports. The aluminum melting furnace working group research achievement report covers aluminum melting furnace operating patterns, concentrated impinging flame mode and dispersed impinging flame mode, and honeycomb and ball structures in heat storing bodies. The tubular heater working group report mentions the application of this facility to oil heating furnaces, studies and investigations for the embodiment of real systems using the tubular heater, and tests conducted in a furnace with plural heating tube lines. The individual research achievement reports elaborate on the development of technologies of heat transfer optimization under unsteady conditions in the steel material heating process, research and development of high-efficiency heat transfer technologies, development of heating furnace geometry optimization technologies, research and development of a high-performance controlled atmosphere heat treatment furnace, development of high-efficiency heat transfer technologies in high-temperature jet flame heating, development of heat uniformity improvement technologies for example for the steel material heating process, construction of optimum combustion control technologies for the regenerative burner furnace,