WorldWideScience

Sample records for chemical yield determination

  1. Determination of the chemical yield on the Fricke dosimetry for 192Ir sources used in brachytherapy

    International Nuclear Information System (INIS)

    David, M.G.; Albuquerque, M.A.G.; Almeida, C.E. de; Rosado, P.H.

    2015-01-01

    With the aim of developing a primary standard for the absorbed dose to water, for the 192 Ir sources used in high dose rate brachytherapy, this work focuses on the determination of the chemical yield, G(Fe +3 ), using Fricke dosimetry, for the energy of those sources . The G(Fe +3 ) were determined the for three qualities of x-ray beams (150, 250 and 300 kV ) and for 60 Co energy. The G(Fe +3 ) value for the average energy of 192 Ir was obtained by linear fit, the found value was 1,555 ± 0,015 μmol/J. (author)

  2. Neutron activation analysis of biological materials for sub PPM amount of mercury without determining the chemical yield

    International Nuclear Information System (INIS)

    Foldzinska, A.; Dybczynski, R.

    1976-01-01

    A simple method for the determination of sub ppm amounts of mercury in various biological materials by neutron activation analysis is described. Irradiated samples were decomposed with H 2 SO 4 - fuming HNO 3 mixture and mercury selectively isolated by ion exchange chromatography using Dowex 50X2(H + ) and Dowex 1X4(Br - ) columns in HBr medium. Finally the activity of 197 Hg fixed on an anion exchange resin was measured either with a Ge(Li) or a NaI (Tl) detector. Both the high radiochemical purity of mercury and the practically quantitative recovery were achieved thus eliminating the necessity of determining the chemical yield. The method was used for the determination of mercury in flour, milk, butter, margarine, fish, etc. Total time of analysis (including counting) amounted to 6-7 hrs and several samples could be simultaneously analysed by one technician. (T.G.)

  3. Chemical yield determination for 59Ni, 63Ni and 56Fe in low and intermediate nuclear wastes by ICP-AES

    International Nuclear Information System (INIS)

    Franco, Milton B.; Santos Neto, Francisco C. dos; Reis Junior, Aluisio S.; Temba, Eliane S.C.; Monteiro, Roberto P.G.

    2011-01-01

    Iron and nickel are constituents of a wide range of metallic materials used in nuclear reactor construction and their corresponding activation products are often encountered in reactor-derived solid low and intermediate-level wastes. The most significant radioisotopes of iron and nickel, in terms of quantity and half life, are 55 Fe (t 1/2 =2.73y), 59 Ni (t 1/2 =7.6x10 4 y) and 63 Ni (t 1/2 =10 2 y) and they are activation products of stable iron and nickel. 59 Ni is an X-ray - emitting and 55 Fe and 63 Ni are β-particle-emitting radionuclides and so they are radionuclides of interest for the performance of assessment studies of waste storage or disposal. For their determination in the radioactive wastes is necessary to know the chemical yield for the radiochemical separation procedures prior analytical measurements. In this work Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) technique was used for this aim. Total nickel and iron in waste samples from nuclear power plants were determined before and after the radiochemical separation at specific wavelengths, 231.604 nm and 259.940 nm respectively. The chemical yields for nickel and iron recovery were around 82 % for iron and 59 % for nickel according the analytical methodology adopted. (author)

  4. Track models and radiation chemical yields

    International Nuclear Information System (INIS)

    Chatterjee, A.; Magee, J.L.

    1987-01-01

    The authors are concerned only with systems in which single track effects dominate and radiation chemical yields are sums of yields for individual tracks. The authors know that the energy deposits of heavy particle tracks are composed of spurs along the particle trajectory (about one-half of the energy) and a more diffuse pattern composed of the tracks of knock-on electrons, called the penumbra (about one-half of the energy). The simplest way to introduce the concept of a unified track model for heavy particles is to consider the special case of the track of a heavy particle with an LET below 0.2-0.3eV/A, which in practice limits us to protons, deuterons, or particles with energy above 100 MeV per nucleon. At these LET values, to a good approximation, spurs formed by the main particle track can be considered to remain isolated throughout the radiation chemical reactions

  5. Yield stress determination of a physical gel

    DEFF Research Database (Denmark)

    Hvidt, Søren

    2013-01-01

    Pluronic F127 solutions form gels in water with high elastic moduli. Pluronic gels can, however, only withstand small deformations and stresses. Different steady shear and oscillatory methods traditionally used to determine yield stress values are compared. The results show that the yield stresses...... values of these gels depend on test type and measurement time, and no absolute yield stress value can be determined for these physical gels....

  6. Cover Crops Effects on Soil Chemical Properties and Onion Yield

    Directory of Open Access Journals (Sweden)

    Rodolfo Assis de Oliveira

    2016-01-01

    Full Text Available ABSTRACT Cover crops contribute to nutrient cycling and may improve soil chemical properties and, consequently, increase crop yield. The aim of this study was to evaluate cover crop residue decomposition and nutrient release, and the effects of these plants on soil chemical properties and on onion (Allium cepa L. yield in a no-tillage system. The experiment was carried out in an Inceptisol in southern Brazil, where cover crops were sown in April 2012 and 2013. In July 2013, shoots of weeds (WD, black oats (BO, rye (RY, oilseed radish (RD, oilseed radish + black oats (RD + BO, and oilseed radish + rye (RD + RY were cut at ground level and part of these material from each treatment was placed in litter bags. The litter bags were distributed on the soil surface and were collected at 0, 30, 45, 60, 75, and 90 days after distribution (DAD. The residues in the litter bags were dried, weighed, and ground, and then analyzed to quantify lignin, cellulose, non-structural biomass, total organic carbon (TOC, N, P, K, Ca, and Mg. In November 2012 and 2013, onion crops were harvested to quantify yield, and bulbs were classified according to diameter, and the number of rotted and flowering bulbs was determined. Soil in the 0.00-0.10 m layer was collected for chemical analysis before transplanting and after harvesting onion in December 2012 and 2013. The rye plant residues presented the highest half-life and they released less nutrients until 90 DAD. The great permanence of rye residue was considered a protection to soil surface, the opposite was observed with spontaneous vegetation. The cultivation and addition of dry residue of cover crops increased the onion yield at 2.5 Mg ha-1.

  7. Using Simulation to Increase Yields in Chemical Engineering

    Directory of Open Access Journals (Sweden)

    William C. Conley

    2003-06-01

    Full Text Available Trying to increase the yields or profit or efficiency (less pollution of chemical processes is a central goal of the chemical engineer in theory and practice. Certainly sound training in chemistry, business and pollution control help the engineer to set up optimal chemical processes. However, the ever changing demands of customers and business conditions, plus the multivariate complexity of the chemical business can make optimization challenging. Mathematical tools such as statistics and linear programming have certainly been useful to chemical engineers in their pursuit of optimal efficiency. However, some processes can be modeled linearly and some can not. Therefore, presented here will be an industrial chemical process with potentially five variables affecting the yield. Data from over one hundred runs of the process has been collected, but it is not known initially whether the yield relationship is linear or nonlinear. Therefore, the CTSP multivariate correlation coefficient will be calculated for the data to see if a relationship exists among the variables. Then once it is proven that there is a statistically significant relationship, an appropriate linear or nonlinear equation can be fitted to the data, and it can be optimized for use in the chemical plant.

  8. Chemical intervention in plant sugar signalling increases yield and resilience

    Science.gov (United States)

    Griffiths, Cara A.; Sagar, Ram; Geng, Yiqun; Primavesi, Lucia F.; Patel, Mitul K.; Passarelli, Melissa K.; Gilmore, Ian S.; Steven, Rory T.; Bunch, Josephine; Paul, Matthew J.; Davis, Benjamin G.

    2016-12-01

    The pressing global issue of food insecurity due to population growth, diminishing land and variable climate can only be addressed in agriculture by improving both maximum crop yield potential and resilience. Genetic modification is one potential solution, but has yet to achieve worldwide acceptance, particularly for crops such as wheat. Trehalose-6-phosphate (T6P), a central sugar signal in plants, regulates sucrose use and allocation, underpinning crop growth and development. Here we show that application of a chemical intervention strategy directly modulates T6P levels in planta. Plant-permeable analogues of T6P were designed and constructed based on a ‘signalling-precursor’ concept for permeability, ready uptake and sunlight-triggered release of T6P in planta. We show that chemical intervention in a potent sugar signal increases grain yield, whereas application to vegetative tissue improves recovery and resurrection from drought. This technology offers a means to combine increases in yield with crop stress resilience. Given the generality of the T6P pathway in plants and other small-molecule signals in biology, these studies suggest that suitable synthetic exogenous small-molecule signal precursors can be used to directly enhance plant performance and perhaps other organism function.

  9. Radiation-chemical yields of molecular hydrogen formation in cyclohexane based alcohols

    International Nuclear Information System (INIS)

    Val'ter, A.I.; Kovalev, G.V.

    1988-01-01

    Molecular hydrogen radiation-chemical yields in γ-irradiated cyclohexanol, 1.2-cis- and 1.2-trans-cyclohexandiols and inositol are determined within the general problem frameworks of radiolysis mechanism for cyclohexanering-base alcohols. Irradiation was conducted at 77 and 293 K, dose rate - 4 Gy/s. Hydrogen concentration in all irradiated alcohols depends linearly on the dose. Radiation-chemical yields of H 2 and of stabilized radicals, as well, in the irradiated crystalline alcohols are analyzed depending on the irradiation temperature, alcohol molecular structure

  10. Comparison of the methods for determination of scintillation light yield

    CERN Document Server

    Sysoeva, E; Zelenskaya, O

    2002-01-01

    One of the most important characteristics of scintillators is the light yield. It depends not only on the properties of scintillators, but also on the conditions of measurements. Even for widely used crystals, such as alkali halide scintillators NaI(Tl) and CsI(Tl), light yield data, obtained by various authors, are different. Therefore, it is very important to choose the convenient method of the light yield measurements. In the present work, methods for the determination of the physical light yield, based on measurements of pulse amplitude, single-electron pulses and intrinsic photomultiplier resolution are discussed. These methods have been used for the measurements of light yield of alkali halide crystals and oxide scintillators. Repeatability and reproducibility of results were determined. All these methods are rather complicated in use, not for measurements, but for further data processing. Besides that, they demand a precise determination of photoreceiver's parameters, as well as determination of light ...

  11. Determination of experimental K-shell fluorescence yield for ...

    Indian Academy of Sciences (India)

    X-ray; fluorescence yield; cross-section and chemical effects; potassium; cal- ... The X-ray production cross-section in Ti, V, Cr, Mn, Fe, Co, Ni and Cu .... where µinc (cm2 g−1) and µemt (cm2 g−1) are the mass attenuation coefficients at the.

  12. Determination of the yield locus by means of temperature measurement

    NARCIS (Netherlands)

    Banabic, D.; Huetink, Han

    2006-01-01

    The paper presents a theoretical background of the thermo-graphical method of determining the yield locus. The analytical expression of the temperature variation of the specimen deformed in the elastic state is determined starting from the first law of thermodynamics. The experimental method for

  13. The Effects of Organic, Chemical and Biological Fertilizers on Seed Yield and Yield Components of Dwarf Chicory (Cichorium pumilum Jacq.

    Directory of Open Access Journals (Sweden)

    Farima Doaei

    2017-08-01

    Full Text Available Introduction: In order to response to greater demand for wild medicinal plants consumption, it has been recommended that wild medicinal plants can be brought into cultivation systems. Cichorium pumilum Jacq. is an annual species of Asteraceae family, that has a long history of herbal use and is especially of great value for its tonic effects upon the liver and digestive tract. The root and the leaves of chicory are digestive, hypoglycemic, diuretic, laxative and tonic. Using chemical fertilizers can be easily lost from soils through fixation, leaching or gas emission that can lead to reduced fertilizer efficiency. The applications of organic fertilizers such as compost and vermicompost can be considered as a good management practice to increase cropping system sustainability, reducing soil erosion and improving soil physical, chemical and biological properties. Soil microorganisms have a significant role in regulating the dynamics of organic matter breakdown and the availability of plant nutrients such as nitrogen, phosphate and sulfur. Materials and Methods: For evaluating the effects of organic, mineral and biological fertilizers on seed yield and yield components of dwarf chicory (Cichorium pumilum Jacq., a field experiment was conducted at the Agricultural Research Station, the Ferdowsi University of Mashhad (36016/ N, 59036/ E, elevation 985 m during growing season of 2011-2012. The experimental layout was factorial based on randomized complete block design with four replications. The experimental treatments were all combination of organic and chemical fertilizers (compost 4 t/ha, vermicompost 4 t/ha, urea fertilizer 130 kg/ha and control and biological fertilizer (biosulfur biofertilizer + pure sulfur 100 kg/ ha and control. Before conducting the experiment, soil sample were taken from the depth of 0-30 cm, and physical and chemical characteristics of the soil and also used compost and vermicompost were determined. All fertilizer

  14. Determination of experimental K-shell fluorescence yield for ...

    Indian Academy of Sciences (India)

    calcium compounds using a Si(Li) X-ray detector system (FWHM=5.96 keV at 160 eV). The samples were excited by 5.96 keV photons produced by a 55Fe radioisotope source. The experimental values are systematically lower than the theoretical values. Keywords. X-ray; fluorescence yield; cross-section and chemical ...

  15. Neem ( Azadirachta indica a. Juss) fruit yield determination in ...

    African Journals Online (AJOL)

    This study determined fruit yield of Neem (Azadirachta indica A. Juss) in the guinea savanna of Nigeria at Makurdi. Fifteen mature neem trees which had no overlapping canopies and had not been previously pruned were purposively selected out of 207 stands growing at the study site. All ripped fruits felling from the ...

  16. Determinants of sovereign debt yield spreads under EMU: Pairwise approach

    NARCIS (Netherlands)

    Fazlioglu, S.

    2013-01-01

    This study aims at providing an empirical analysis of long-term determinants of sovereign debt yield spreads under European EMU (Economic and Monetary Union) through pairwise approach within panel framework. Panel gravity models are increasingly used in the cross-market correlation literature while

  17. Determinants of bond yield spread changes in South Africa | Radier ...

    African Journals Online (AJOL)

    This paper offers an emerging market perspective on the determinants of bond yield spread changes. The study covers the period 2005-2013 and it is based on a sample of 106 corporate vanilla bonds listed on the South African market. To capture the impact of the financial crisis of 2007-2008, the sample period is split into ...

  18. Spatial distribution of the chemical properties of the soil and of soybean yield in the field

    Directory of Open Access Journals (Sweden)

    Alexandre Gazolla-Neto

    2016-06-01

    Full Text Available ABSTRACT The aim of this study was to evaluate the spatial dependence between chemical properties of the soil and yield components in the soybean using precision farming techniques. Samples of the soil and plants were taken from georeferenced points to determine the chemical properties of the soil and the yield components. The results were submitted to Pearson correlation analysis, descriptive statistics and geostatistics. The coefficient of variation showed a wide range of distribution for the chemical attributes of the soil, with the highest indices being found for the levels of available phosphorus (102% and potassium (72.65%. Soil pH and organic matter showed a coefficient of variation of 5.96 and 15.93% respectively. Semivariogram analysis of the yield components (productivity, 1,000-seed weight and number of seeds and the chemical properties of the soil (organic matter, pH, phosphorus, potassium, calcium, magnesium, boron, manganese and zinc fitted the spherical model with moderate spatial dependence, with values ranging from 200 to 700 m. Spatial distribution by means of map interpolation was efficient in evaluating spatial variability, allowing the identification and quantification of regions of low and high productivity in the production area, together with the distribution of soil attributes and their respective levels of availability to the soybean plants.

  19. Non-Equilibrium Heavy Flavored Hadron Yields from Chemical Equilibrium Strangeness-Rich QGP

    OpenAIRE

    Kuznetsova, Inga; Rafelski, Johann

    2008-01-01

    The yields of heavy flavored hadrons emitted from strangeness-rich QGP are evaluated within chemical non-equilibrium statistical hadronization model, conserving strangeness, charm, and entropy yields at hadronization.

  20. The effects of vermicompost and chemical fertilizers on yield and yield components of marshmallow (Altheae officinalis L.)

    OpenAIRE

    A.A. Sadeghi; K. Bakhsh Kelarestaghi; K. Hajmohammadnia Ghalibaf

    2016-01-01

    In order to investigate the effects of vermicompost and chemical fertilizers on growth characteristics, yield and yield components of marshmallow (Altheaeofficinalis L.), a field experiment was conducted as factorial layout based on a randomized complete block design with three replications at Faculty of Agriculture, Ferdowsi University of Mashhad, Iran, during growing season of 2012. Experimental treatments were designed based on 3 levels of vermicompost (0, 5 and 10 t ha-1) and 5 levels of ...

  1. Nuclear yield determinations using isotope-separator-on-line arrangements

    International Nuclear Information System (INIS)

    Rudstam, G.

    1975-01-01

    The delay between the formation of a nuclear reaction product and its collection in front of measuring equipment in ISOL arrangements using integrated target-ion source systems has been analyzed. It is shown that a typical delay function takes the form const x (1-esup(-γt))esup(-μt) with γ >> μ. The results can be used for decay corrections in nuclear yield determinations. (Auth.)

  2. Determination of the alcohol-yielding capacity of cereals. A method for the determination of the alcohol-yielding capacity

    Energy Technology Data Exchange (ETDEWEB)

    Frey, A; Hoppe, W

    1957-01-01

    A laboratory method is reported for the determination of the alcohol yielding capacity of starch-containing distillery raw materials. The starch is inverted with dilute HCl under pressure, after which the material is fermented with yeast at pH 5.4. After distillation, the alcohol is determined pyknometrically. The influence of such factors as amount of yeast was determined experimentally. Analysis of the time curves for the hydrolysis of starch (by paper-chromatographic techniques) in relation to pH showed glucose to be the principal reaction product, with only slight amounts of maltose and higher sugars being formed.

  3. effects of preharvest treatments on yield and chemical composition

    African Journals Online (AJOL)

    Administrator

    altitude of 1197 m above sea level and lies at 9o6'N ... widest point form the upper, middle and lower part of the plant was ... heated in boiling water bath for sufficient time until the ..... al., 1970 reported yield increase in tomato due to nitrogen ...

  4. Determination of secondary electron yields from low pressure breakdown

    International Nuclear Information System (INIS)

    Maric, D; Zivanov, S.; Strinic, A.; Malovic, G.; Djuric, M.; Petrovic, Z. Lj.

    2000-01-01

    In order to model accurately the secondary yields in gas breakdown and collisional plasmas both the numerous processes discussed in related experiments must be included and also proper determination of γ (E/n) must be provided. In addition to the application of the correct ionization rate it is also essential to include the nonequilibrium region where electrons gain energy and achieve hydrodynamics equilibrium. For lower values of E/n, greater values of γ than those based on the literature data for αn(E/n) have been found, possibly due to existence of the photoelectric effects

  5. Applications of pressurized cation exchange chromatography for fission yield determination

    International Nuclear Information System (INIS)

    Yan Shuheng; Lin Fa; Zhang Hongdi; Li Xueliang; Zhang Shulan

    1988-01-01

    In order to determine the fission yields of lanthanides precisely, lanthanides with carriers of 1-2 mg per element are separated from each other by means of pressurized cation exchange chromatography - αHIBA concentration gradient elution. The effect of initial loading technique, concentration gradient, flow rate, and temperature on separation were investigated in detail. Under the optimum conditions adapted according to the results given in this work, all the lanthanides can be completely separated within about 90 minutes with a recovery of more than 95% and purity higher than 99%. (author) 3 refs.; 6 figs

  6. The effects of vermicompost and chemical fertilizers on yield and yield components of marshmallow (Altheae officinalis L.

    Directory of Open Access Journals (Sweden)

    A.A. Sadeghi

    2016-05-01

    Full Text Available In order to investigate the effects of vermicompost and chemical fertilizers on growth characteristics, yield and yield components of marshmallow (Altheaeofficinalis L., a field experiment was conducted as factorial layout based on a randomized complete block design with three replications at Faculty of Agriculture, Ferdowsi University of Mashhad, Iran, during growing season of 2012. Experimental treatments were designed based on 3 levels of vermicompost (0, 5 and 10 t ha-1 and 5 levels of nitrogen fertilizer (0, 25, 50, 75 and 100% of 200 kg N ha-1. Results indicated that applied vermicompost had significant effects on increasing leaf area, flower weight per plant and grain yield of marshmallow. Flower weight per plant and grain yield of marshmallow was increased by 2 to 3 times by applying vermicompost at 10 t. ha-1, as compared to control treatment. In addition, nitrogen fertilizer had a significant effect on increasing flower weight per plant and grain, mucilage and oil yields of marshmallow. It seems that applying vermicompost can be suitable strategy in reducing the problems caused by excessive using of chemical fertilizers.

  7. Cacao Crop Management Zones Determination Based on Soil Properties and Crop Yield

    Directory of Open Access Journals (Sweden)

    Perla Silva Matos de Carvalho

    Full Text Available ABSTRACT: The use of management zones has ensured yield success for numerous agricultural crops. In spite of this potential, studies applying precision agricultural techniques to cacao plantations are scarce or almost nonexistent. The aim of the present study was to delineate management zones for cacao crop, create maps combining soil physical properties and cacao tree yield, and identify what combinations best fit within the soil chemical properties. The study was conducted in 2014 on a cacao plantation in a Nitossolo Háplico Eutrófico (Rhodic Paleudult in Bahia, Brazil. Soil samples were collected in a regular sampling grid with 120 sampling points in the 0.00-0.20 m soil layer, and pH(H2O, P, K+, Ca2+, Mg2+, Na+, H+Al, Fe, Zn, Cu, Mn, SB, V, TOC, effective CEC, CEC at pH 7.0, coarse sand, fine sand, clay, and silt were determined. Yield was measured in all the 120 points every month and stratified into annual, harvest, and early-harvest cacao yields. Data were subjected to geostatistical analysis, followed by ordinary kriging interpolation. The management zones were defined through a Fuzzy K-Means algorithm for combinations between soil physical properties and cacao tree yield. Concordance analysis was carried out between the delineated zones and soil chemical properties using Kappa coefficients. The zones that best classified the soil chemical properties were defined from the early-harvest cacao yield map associated with the clay or sand fractions. Silt content proved to be an inadequate variable for defining management zones for cacao production. The delineated management zones described the spatial variability of the soil chemical properties, and are therefore important for site-specific management in the cacao crop.

  8. Applicability and methodology of determining sustainable yield in groundwater systems

    Science.gov (United States)

    Kalf, Frans R. P.; Woolley, Donald R.

    2005-03-01

    There is currently a need for a review of the definition and methodology of determining sustainable yield. The reasons are: (1) current definitions and concepts are ambiguous and non-physically based so cannot be used for quantitative application, (2) there is a need to eliminate varying interpretations and misinterpretations and provide a sound basis for application, (3) the notion that all groundwater systems either are or can be made to be sustainable is invalid, (4) often there are an excessive number of factors bound up in the definition that are not easily quantifiable, (5) there is often confusion between production facility optimal yield and basin sustainable yield, (6) in many semi-arid and arid environments groundwater systems cannot be sensibly developed using a sustained yield policy particularly where ecological constraints are applied. Derivation of sustainable yield using conservation of mass principles leads to expressions for basin sustainable, partial (non-sustainable) mining and total (non-sustainable) mining yields that can be readily determined using numerical modelling methods and selected on the basis of applied constraints. For some cases there has to be recognition that the groundwater resource is not renewable and its use cannot therefore be sustainable. In these cases, its destiny should be the best equitable use. sostenible. Las razones son: (1) los conceptos y definiciones actuales son ambiguos y sin base física de modo que no pueden usarse para aplicación cuantitativa, (2) existe necesidad de eliminar interpretaciones variables y mal interpretaciones y aportar bases sanas para aplicación, (3) la noción de que todos los sistemas de aguas subterráneas son o pueden ser sostenibles no esvalida, (4) frecuentemente existen un numero excesivo de factores ligados a la definición de producción sostenible los cuales no son fácil de cuantificar, (5) frecuentemente existe confusión entre la producción optima de un establecimiento y la

  9. Residual Effect of Chemical and Animal Fertilizers and Compost on Yield, YieldComponents, Physiological Characteristics and Essential Oil Content of Matricaria chamomilla L. under Drought Stress conditions

    Directory of Open Access Journals (Sweden)

    a Ahmadian

    2011-02-01

    Full Text Available Abstract The residual effect of inorganic and organic fertilizers on growth and yield of plants is one of the important problems in nutrition. This study was conducted to determine the residual effect of different fertilizers on yield, yield components, physiological parameters and essential oil percentage of Matricaria chamomilla under drought stress. A split plot arrangement based on randomized completely block design (RCBD with three replication was conducted in 2009, at the University of Zabol. Treatments included W1 (non stress, W2 (75% FC and W3 (50% FC as main plot and three types of residual’s fertilizers: F1 (non fertilizer, F2 (chemical fertilizer, F3 (manure fertilizer and F4 (compost as sub plot. Results showed that water stress at W3 treatment reduced dry flower yield. Low water stress increased essential oil percentage and the highest oil was obtained in W2. In this experiment, free proline and total soluble carbohydrate concentration were increased under water stress. The residual’s manure and compost enhanced flower yield, percentage and yield of essential oil of chamomile at the second year. At a glance, animal manure application and light water stress (75% FC was recommended to obtain best quantitative and qualitative yield. Keywords: Water Stress, Fertilizer, Carbohydrate, Proline, Chamomile

  10. Spectroscopy characterization and quantum yield determination of quantum dots

    International Nuclear Information System (INIS)

    Ortiz, S N Contreras; Ospino, E Mejía; Cabanzo, R

    2016-01-01

    In this paper we show the characterization of two kinds of quantum dots: hydrophilic and hydrophobic, with core and core/shell respectively, using spectroscopy techniques such as UV-Vis, fluorescence and Raman. We determined the quantum yield in the quantum dots using the quinine sulphate as standard. This salt is commonly used because of its quantum yield (56%) and stability. For the CdTe excitation, we used a wavelength of 549nm and for the CdSe/ZnS excitation a wavelength of 527nm. The results show that CdSe/ZnS (49%) has better fluorescence, better quantum dots, and confirm the fluorescence result. The quantum dots have shown a good fluorescence performance, so this property will be used to replace dyes, with the advantage that quantum dots are less toxic than some dyes like the rhodamine. In addition, in this work we show different techniques to find the quantum dots emission: fluorescence spectrum, synchronous spectrum and Raman spectrum. (paper)

  11. Investigation of Yield and Yield Components of Canary Seed Forage (Phalaris canariensis L. in Response to Different Levels of Irrigation, Organic and Chemical Fertilizers and their integration

    Directory of Open Access Journals (Sweden)

    V Varnaseri Ghandali

    2016-12-01

    Full Text Available Introduction Canary seed (Phalaris canariensis L. is a forage plant from Poaceae family. This plant is drought tolerant. Canary seed is originally a native to Mediterranean region, which can be grown commercially in several parts of the word, especially in semi-arid conditions. Increasing growth of population and lack of ability of pastures to satisfy the food requirement of animal has led to more interest in cultivating forage plants. In this regard, Canary seed having properties such as high yield per unit area, high tillering power, very fast growth and appropriate nutritional value, is of considerable importance and its cultivation development especially in arid and semi-arid regions can be effective in providing part of the country forage needs. Optimum water requirement is considered as one the important factors to obtain a high growth and yield of the product. On the other hand, Iran is located in arid and semi-arid climate region of the world . Therefore, determination of appropriate amount of irrigation water can lead to the improvement of water use efficiency and preventing the water loss. In order to achieve a high yield and desirable quality in plants one of the important requirements in agricultural planning is the evaluation of different systems of plant feeding. By applying an appropriate method in soil productivity, in addition to protecting the environment, optimization of water usage, reduction of erosion and protection of biodiversity can be increased. Therefore, gradually replacing chemical fertilizers with biological and organic fertilizers will result in providing feed requirements of plants, improvement of physical, chemical and biological conditions of soil and reduction of adverse environmental effects resulting from application of chemical inputs. The aim of this research was to study the effects of deficit irrigation and fertilizer management based on sole chemical and organic fertilizers or their integrated

  12. DETERMINATION THE EFFECT OF DEFOLIATION TIMING ON COTTON YIELD AND QUALITY

    Directory of Open Access Journals (Sweden)

    Karademir Emine

    2007-12-01

    Full Text Available This study was carried out for determining the effect of different application times at 40, 50, 60 and 70 % boll opening and untreated plot of the defoliant on cotton yield, earliness and technological properties in Southeast Anatolia Region conditions in Turkey. Maras 92 cotton variety was used as plant material in the experiment field of the Southeast Anatolia Agricultural Research Institute during 2000-2001. Defoliant was including thidiazuron + diuron chemical substance. The result of this study showed that ginning percentage, 100 seed weight, seed germination percentage, fiber fineness, fiber length, fiber strength, reflectance, elongation and seed cotton yield were not affected by the treatment; plant height and first picking percentage in 2001, fiber uniformity in 2000 were 5 % significantly affected. This study showed that application of defoliant didn’t affect significantly yield and technological properties of cotton and after 40 % boll opening the defoliant can be used.

  13. Influence of tumbling and phosphate on the yield, sensory and chemical characteristics of pork liver loaf

    NARCIS (Netherlands)

    Percel, P.J.; Parrett, N.A.; Plimpton, R.F.; Ockerman, H.W.; Krol, B.; Roon, P.S. van

    1982-01-01

    Yield, sensory and chemical properties of pork liver loaves manufactured using varying processing treatments (tumbling vs immersion) and phosphate levels (0 vs 6.4%) were studied. Tumbling significantly improved liver cure uptake, total cure and loaf cooked yield when compared to immersion as a

  14. Determination of fission gas yields from isotope ratios

    DEFF Research Database (Denmark)

    Mogensen, Mogens Bjerg

    1983-01-01

    This paper describes a method of calculating the actual fission yield of Kr and Xe in nuclear fuel including the effect of neutron capture reactions and decay. The bases for this calculation are the cumulative yields (ref. 1) of Kr and Xe isotopes (or pairs of isotopes) which are unaffected...... by neutron capture reactions, and measured Kr and Xe isotope ratios. Also the burnup contribution from the different fissile heavy isotopes must be known in order to get accurate fission gas yields....

  15. Lawrence Livermore National Laboratory seismic yield determination for the NPE

    Energy Technology Data Exchange (ETDEWEB)

    Rohrer, R. [Lawrence Livermore National Lab., CA (United States)

    1994-12-31

    The Lawrence Livermore National Laboratory recorded seismic signals from the Non-Proliferation experiment at the Nevada Test Site on September 22, 1993, at seismic stations near Mina, Nevada; Kanab Utah; Landers, California; and Elko, Nevada. Yields were calculated from these recorded seismic amplitudes at the stations using statistical amplitude- yield regression curves from earlier nuclear experiments performed near the Non-Proliferation experiment. The weighted seismic yield average using these amplitudes is 1.9 kt with a standard deviation of 19%. The calibrating experiments were nuclear, so this yield is equivalent to a 1.9-kt nuclear experiment.

  16. Effects of Chemical and Organic Fertilizers on Growth, Yield and Yield Component of Tomato (Lycopersicon sculentum L.

    Directory of Open Access Journals (Sweden)

    R Mirzaei Talarposhti

    2017-03-01

    Full Text Available Introduction Although using animal manures and crop residues as a traditional method for increasing soil fertility and crop yield has a long history but Conventional agricultural systems rely on the use of chemical fertilizer due to its immediate availability of nutrients. In many of modern agricultural systems using chemical fertilizers as a fast and easiest way to reduce nutrient deficiency and increasing soil fertility is considered. Intensive and continuous use of chemical fertilizers leads to decreasing the stability and sustainability of agricultural systems and also poses major threat to environment and human health. Organic fertilizers have positive effects on physiochemical and biological attributes of soil and could be classified in three different groups (i.e. Animal manures, green manure and composts.Using animal manure not only increase soil fertility but also could result in increasing infiltration, aeration and water holding capacity of soil. The main role of these fertilizers is related to physical change in soil. Different types of composts such as municipal waste compost and vermicompost also have similar positive effects, but usually the farmers observe the main effect of these organic fertilizers in long term. In order to investigate the effects of different types of organic fertilizers on growth indexes, yield and yield component of tomato (Lycopersicon sculentum L. current experiment was conducted. Materials and Methods The experiment was conducted based on randomized complete block design (RCBD with three replications and six treatments in the research station of Shahid Beheshti University. The experimental treatments were: Control or no fertilizer (NF, chemical fertilizer (CF, cow manure (CM, poultry manure (PM, vermicompost (VC and municipal waste compost (MC. Considering nitrogen concentration in all of the treatments different amounts of these fertilizers were used based on nitrogen recommendation for the field, so in

  17. Determination of ontogenetic selection criteria for grain yield in ...

    African Journals Online (AJOL)

    STORAGESEVER

    2009-06-03

    Jun 3, 2009 ... spring barley in cool and short-season environments. Key words: ... Many researchers have used a linear correlation analysis ... of each yield component on grain yield from the indirect ... ANOVA was carried out using the SPSS statistics programme ..... stable characteristic in barley (Gallagher et al., 1975),.

  18. Test of two methods for determining herbaceous yield and botanical ...

    African Journals Online (AJOL)

    Above-ground herbaceous yield was estimated using the comparative yield method to win + 10% (p < 0,05) of the harvested mean using 150 harvested and 600 rated quadrats of 50 x 50 cm. The number of quadrats can be substantially reduced by improved observer rating. Using the dry mass rank method and 240 ...

  19. The Effect of Chemical, Biological and Organic Nutritional Treatments on Sunflowers Yield and Yield Components under the Influence of Water Deficit Stress

    Directory of Open Access Journals (Sweden)

    fatemeh soleymani

    2016-07-01

    Azospirilium lipoferum was impregnated with seeds. Vermicompost was mixed with the soil before planting based on the recommendation of the producer company (15 t.ha-1. After determining evapotranspiration of the reference plant (ET0 by FAO- Penman-Monteith method and crop coefficients (Kc in different stages of crop growth, plant water requirement was determined (Allen et al., 1998. Finally, the irrigation water volume was estimated according to the effective rainfall, irrigation efficiency (60% and 45% depletion of soil moisture in the root zone (Doorenbos & Kassam, 1979. Results and discussion Water deficit stress and nutrient treatments significantly affected all measured traits except the harvest index. Water deficit stress significantly reduced head diameter by 24% in comparison with optimum irrigation. The maximum diameter (17.03 cm was obtained in vermicompost treatment. One thousand seed weight of sunflower under optimum irrigation was 1.3 times as much as water deficit treatment. Combined treatment of vermicompost and half of recommended chemical fertilizer yielded maximum 1000- seed weight (56.67 g. Under optimum irrigation, the highest weight of the head was achieved from 100% chemical fertilizer application, while under water stress, maximum head weight (830.67 g was obtained in vermicompost treatment and the minimum value (485.33 g was obtained from chemical fertilizer + vermicompost + phospho nitro kara. In both irrigation levels, the highest biological yield was obtained from full application of chemical fertilizer, but this treatment in stress condition did not have significant difference with combined application of vermicompost and half of chemical fertilizer, vermicompost and 50% of chemical fertilizer. 100% recommended chemical fertilizer in optimum irrigation, had a maximum grain yield (693.67 g.m-2. Organic fertilizers by increasing soil organic matter, improving soil chemical properties such as pH and CEC, increasing the activity of microorganisms and

  20. Kinetics of methane fermentation yield in biogas reactors: Genetic variation and association with chemical composition in maize

    International Nuclear Information System (INIS)

    Grieder, Christoph; Mittweg, Greta; Dhillon, Baldev S.; Montes, Juan M.; Orsini, Elena; Melchinger, Albrecht E.

    2012-01-01

    Maize (Zea mays L.) is the most competitive crop for methane production in Germany. Methane fermentation yield per unit of dry matter (MFY) is a determinant of methane yield, but little information is available on this trait. Our objectives were to investigate the kinetics of MFY during fermentation of maize, estimate quantitative-genetic parameters for different traits related to MFY and examine the relationship of MFY with chemical composition and silage quality. Whole-plant material of 16 inbreds and their 32 testcrosses was analyzed for MFY over 35 days of fermentation using a discontinuous laboratory assay. Data were also generated on chemical composition and in vitro digestible organic matter (IVDOM). Significant genotypic variances and high heritabilities were observed for MFY at early fermentation stages (up to 5 days) probably due to different concentrations of easily degradable chemical components. However, genotypic variances and heritability of MFY reduced as fermentation progressed, because of complete or partial degradation of all chemical components. Further, there were strong correlations of MFY with chemical components at early fermentation stages but not at later stages. Therefore, MFY at later stages, which is closer to potential MFY, does not seem to be amenable to selection. High heritability of IVDOM and its strong correlation with MFY in testcrosses indicated its possible use for preliminary or indirect selection. Keeping in view the magnitude of genetic variance that was low for MFY and high for dry matter yield (DMY), the other component of methane yield, more emphasis on breeding for DMY seems appropriate. -- Highlights: ► We investigated methane fermentation yield (MFY) of diverse germplasm of maize. ► The kinetics of MFY and its correlations with chemical composition were examined. ► Genetic variance and heritability for MFY decreased with fermentation time. ► Complete fermentation (35 d) reduced correlations of MFY with chemical

  1. Determining the Most Important Soil Properties Affecting the Yield of Saffron in the Ghayenat Area

    Directory of Open Access Journals (Sweden)

    amir ranjbar

    2016-02-01

    Full Text Available Introduction: Saffron is one of the most important economic plants in the Khorasan province. Awareness of soil quality in agricultural lands is essential for the best management of lands and for obtaining maximum economic benefit. In general, plant growth is a function of environmental factors especially chemical and physical properties of soil (20. It has been demonstrated that there was a positive and high correlation between soil organic matter and saffron yield. Increasing the yield of saffron due to organic matter is probably due to soil nutrient, especially phosphorous and nitrogen and also improvement of soil physical quality (6, 28, 29. The yield of saffron in soils with high nitrogen as a result of vegetative growth is high (8. Shahandeh (6 found that most of the variation of saffron yield depends on soil properties. Due to the economic importance of saffron and the role of soil properties on saffron yield, this research was conducted to find the relationship between saffron yield and some soil physical and chemical properties, and to determine the contribution of soil properties that have the greatest impact on saffron yield in the Ghayenat area. Materials and Methods: This research was performed in 30 saffron fields (30 soil samples of the Ghayenat area (longitude 59° 10΄ 10.37˝ - 59° 11΄ 38.41˝ and latitude 33° 43΄ 35.08˝ - 33΄ 44΄ 02.78˝, which is located in the Khrasan province of Iran. In this research, 21 soil properties were regarded as the total data set (TDS. Then the principal component analysis (PCA was used to determine the most important soil properties affecting saffron yield as a minimum data set (MDS and the stepwise regression to estimate saffron yield. To estimate the yield of saffron in stepwise regression method, saffron yield was considered as a dependent variable and soil physical and chemical properties were considered to be independent variables. Results and Discussion: According to the PCA method

  2. Protein Structure Determination Using Chemical Shifts

    DEFF Research Database (Denmark)

    Christensen, Anders Steen

    is determined using only chemical shifts recorded and assigned through automated processes. The CARMSD to the experimental X-ray for this structure is 1.1. Å. Additionally, the method is combined with very sparse NOE-restraints and evolutionary distance restraints and tested on several protein structures >100...

  3. Determination of the chemical composition, the physicochemical ...

    African Journals Online (AJOL)

    The chemical composition of the seed of Telfairia occidentalis (fluted pumpkin), the physicochemical properties of the seed oil and the amino acids profiles of the seed protein have been determined. In proximate composition, the crude fat content of 58.41% indicates that the plant seed is an oil seed. Its protein content of ...

  4. Predicting oil and gas compositional yields via chemical structure-chemical yield modeling (CS-CYM): Part 1 - Concepts and implementation

    Energy Technology Data Exchange (ETDEWEB)

    Freund, H.; Walters, C.C.; Kelemen, S.R.; Siskin, M.; Gorbaty, M.L.; Curry, D.J.; Bence, A.E. [ExxonMobil Research & Engineering Co., Annandale, NJ (United States)

    2007-07-01

    We have developed a method to calculate the amounts and composition of products resulting from the thermal decomposition of a solid complex carbonaceous material. This procedure provides a means of using laboratory measurements of complex carbonaceous solids to construct a representative model of its chemical structure (CS) that is then coupled with elementary reaction pathways to predict the chemical yield (CY) upon thermal decomposition. Data from elemental analysis, H, N, O, S, solid state {sup 13}C NMR, X-ray photoelectron spectroscopy (XPS), sulfur X-ray absorption structure spectroscopy (XANES), and pyrolysis-gas chromatography (GC) are used to constrain the construction of core molecular structures representative of the complex carbonaceous material. These core structures are expanded stochastically to describe large macromolecules ({gt} 10{sup 6} cores with similar to 10{sup 6} atoms) with bulk properties that match the experimental results. Gas, liquid and solid product yields, resulting from thermal decomposition, are calculated by identifying reactive functional groups within the CS stochastic ensemble and imposing a reaction network constrained by fundamental thermodynamics and kinetics. An expulsion model is added to the decomposition model to calculate the chemical products in open and closed systems. Product yields may then be predicted under a wide range of time-temperature conditions used in rapid laboratory pyrolysis experiments, refinery processes, or geologic maturation.

  5. significance of rice sheath photosynthesis: yield determination by c ...

    African Journals Online (AJOL)

    ACSS

    1State Key Laboratory of Hybrid Rice, Hunan Hybrid Rice Research Center, Changsha 410125, P.R. China. 2School of ... for contribution rates of sheath photosynthesis to economical yield. ..... related processes during ripening in rice plants.

  6. Effect of Non-chemical Procedures of Weed Management on Growth Characteristics and Yield of Cumin (Cuminnum cyminum L.

    Directory of Open Access Journals (Sweden)

    Surur Khorramdel

    2018-02-01

    weed infested control. Operation of tillage at night performed with moon light. Seed bed prepared, irrigated and weed removed at 28th February by using surface cultivation for false seed bed treatment. Cover crops removed and added to the soil at 5th March. After land preparation, 2.5 t.ha-1 crop residues of each species added to the soil. Cover crops planted as dense at 5th November then all plots irrigated and then seeding operation was done. Plant height, yield components, biological yield, seed yield, essential oil content and essential oil yield of cumin were measured accordingly. The treatments were run as an analysis of variance (ANOVA to determine if significant differences existed among treatments means. Multiple comparison tests were conducted for significant effects using the LSD test. Results and Discussion The results showed that the growth characteristics, yield components, biological yield, seed yield and essential oil yield of cumin were significantly affected by non-chemical management procedures (p≤0.01. The maximum biological and seed yield were observed in hairy vetch with 220.7 and 103.1 g. m-2 and these minimum were for control with 72.4 and 28.6 g. m-2, respectively. These traits enhanced more than 100% for all management treatments compared to control. The highest essential oil yield of cumin was recorded in hairy vetch (2.8 g. m-2 and the lowest was for control (0.6 g.m-2. Conclusion Non-chemical weed management strategies had significantly effect on plant height, yield components and yield of cumin. Cover crops and crop residues enhanced cumin yield due to physical and chemical soil characteristics, moisture conservation and cell swelling improvement that they increased growth and production of photosynthetic matters. Generally, cover crop is a safe and effective technique for weed control that may decrease the necessity for chemical approaches to crop and soil. Acknowledgement This research (24119.2 was funded by Vice Chancellor for

  7. Effect of Indigenous Pseudomonas sp. and Bacillus sp. Strains on Yield and Main Chemical Growth Parameters of Radicchio

    Directory of Open Access Journals (Sweden)

    Stanojković-Sebić Aleksandra

    2018-03-01

    Full Text Available Pseudomonas sp. and Bacillus sp. belong to plant growth promoting rhizobacteria which are able to colonize the plants roots and stimulate growth. In this study, the effect of two indigenous plant growth promoting rhizobacterial strains Pseudomonas sp. Q4 and Bacillus sp. Q10 and their mixture (mix Q4+Q10 on content of the main chemical growth parameters (nitrogen, phosphorus, potassium, calcium and magnesium and the yield of dry biomass of radicchio (Cichorium spp. var. rossa di treviso aerial parts and root, was investigated. The study was carried out with stagnosol type of soil in pot experiments under semi-controlled conditions in the Institute of Soil Science (Belgrade, in the period from July to October in 2013. Phosphorus was determined by spectrophotometer, potassium - by flame emission photometry and total nitrogen and carbon - using elemental CNS analyzer, while calcium and magnesium were determined by AAS. The data on yield of both aerial parts and root dry biomass of radicchio showed that its treatment with Q4 and Q10 strains, as well as with their mixture, caused noticeably increase in this parameter in relation to the control, whereby the strain Q4 was more effective for aerial parts, while mix Q4+Q10 - for roots. The obtained data on the studied chemical parameters of radicchio root and aerial parts were in total accordance with their yield. Concluding, studied strains have a potential in promoting the biomass yield and main chemical growth parameters of both aerial parts and root of radicchio.

  8. Significance of rice sheath photosynthesis: Yield determination by ...

    African Journals Online (AJOL)

    Using high-yielding hybrid rice Liangyopeijiu (LYP9), its male parent 9311 and hybrid rice Shanyou 63 (SY63) as the experimental materials, the photosynthesis of rice sheath was studied by 14C radio-autography. The results showed that rice sheath could trap sunlight and produce photosynthates, and these ...

  9. Yield stress determination from miniaturized disk bend test data

    International Nuclear Information System (INIS)

    Sohn, D.S.; Kohse, G.; Harling, O.K.

    1985-04-01

    Methodology for testing 3.0 mm diameter by 0.25 mm thick disks by bending in a punch and die has been described previously. This paper describes the analysis of load/deflection data from such miniaturized disk bend tests (MDBT) using a finite element simulation. Good simulation has been achieved up to a point just beyond the predominantly elastic response, linear initial region. The load at which deviation from linearity begins has been found to correlate with yield stress, and yield stress has been successfully extracted from disk bend tests of a number of known materials. Although finite element codes capable of dealing with large strains and large rotations have been used, simulation of the entire load/deflection curve up to fracture of the specimen has not yet been achieved

  10. Sequential Path Analysis for Determination of Relationship Between Yield and Yield Components in Bread Wheat (Triticum aestivum.L.

    Directory of Open Access Journals (Sweden)

    Mohtasham MOHAMMADI

    2014-03-01

    Full Text Available An experiment was conducted to evaluate 295 wheat genotypes in Alpha-Lattice design with two replications. The arithmetic mean and standard deviation of grain yield was 2706 and 950 (kg/ha,respectively. The results of correlation coefficients indicated that grain yield had significant and positive association with plant height, spike length, early growth vigor and agronomic score. Whereas there were negative correlation coefficients between grain yield and days to physiological maturity and canopy temperature before and during anthesis. Path analysis indicated agronomic score and plant height had high positive direct effects on grain yield, while canopy temperature before and during anthesis, and days to maturity, wes another trait having negative direct effect on grain yield. The results of sequential path analysis showed the traits that accounted as a criteria variable for high grain yield were agronomic score, plant height, canopy temperature, spike length, chlorophyll content and early growth vigor, which were determined as first, second and third order variables and had strong effects on grain yield via one or more paths. More important, as canopy temperature, agronomic score and early growth vigor can be evaluated quickly and easily, these traits may be used for evaluation of large populations.

  11. Determination of expected alcohol yield from molasses by laboratory fermentation

    Energy Technology Data Exchange (ETDEWEB)

    Medintseva, L L

    1960-01-01

    Molasses (750 g, 18 to 19% dry weight) in 31 media, supplemented with nutrients was fermented with the industrial yeast strain. The expected alcohol yield was calculated for 1 kg conventional starch as B = V/P..pi.. 0.95, where V is the amount of alcohol distilled from the fermented medium in ml, P is the weight of molasses in g, is the fermentable sugar content of the molasses in percent, and 0.95 is the conversion factor from sucrose to starch.

  12. Potential of commodity chemicals to become bio-based according to maximum yields and petrochemical prices

    NARCIS (Netherlands)

    Straathof, Adrie J.J.; Bampouli, A.

    2017-01-01

    Carbohydrates are the prevailing biomass components available for bio-based production. The most direct way to convert carbohydrates into commodity chemicals is by one-step conversion at maximum theoretical yield, such as by anaerobic fermentation without side product formation. Considering these

  13. Chemical yields from low-temperature pyrolysis of CCA-treated wood

    Science.gov (United States)

    Qirong Fu; Dimitris Argyropolous; Lucian Lucia; David Tilotta; Stan Lebow

    2009-01-01

    Low-temperature pyrolysis offers a feasible option for wood-waste management and the recovery of a variety of useful chemicals. The effect of chromated copper arsenate (CCA) wood preservative on the yield and composition of various pyrolysis products was investigated in the present research. A novel quantitative 31P nuclear magnetic resonance (...

  14. Slifers revisited: a method for determining yields independent of radiochemical measurements

    International Nuclear Information System (INIS)

    Rambo, J.T.

    1976-01-01

    It would be very desirable if an independent method other than radiochemical measurement were available to determine the yields of low-yield events in the alluviums and tuffs of areas 2, 9, and 10 at the Nevada Test Site. The successful application of slifers to the measurement of yields from high-yield events suggests that under some conditions they may also be usable with low-yield events. This view is supported by the evidence discussed here, which is based on direct experience with slifer yield measurements for low-yield events in porous media. Suggested methods for improving slifer yield determinations and a method for determining yields independent of radiochemical measurements are offered

  15. Determination of primary yields in the alpha radiolysis of alkaline water

    International Nuclear Information System (INIS)

    Auclair, Guy

    2001-01-01

    This work presents a fundamental study of the radiolysis of water within the framework of the management of nuclear waste. During their storage, the packages of cemented radioactive waste are likely to release molecular hydrogen. Indeed, interstitial water undergoes decomposition under irradiation. This phenomenon is called radiolysis. In order to envisage the impact of H 2 de-gasification on the security of the installations, it is necessary to determine the primary radiolytic yields in the cementing medium (characterised by a pH ranging between 12 and 14), which provides a basic simulations thus allowing us to obtain both the quantities of gas and the pressure in the pore. Such data is currently not available in the literature. Studies were undertaken with a beam of accelerated helium ions in order to reproduce the conditions of irradiation on solutions at pH = 13 in order to determine a first complete series of radiolytic yields.A more complete study was undertaken on the effects of LET and pH on the yield of molecular hydrogen. The results seem to show that the yield of this primary product is little influenced by pH. Such results were in good agreement with those obtained by Monte-Carlo simulations. These studies have shown that, contrary to γ irradiations, the irradiations with α-particles do not lead to the same characteristic times. The extrapolation of this data with respect to the problem of the packaging of nuclear waste is delicate due to the limited amount of results in the literature and also the chemical and physical complexity of the concretes. (author) [fr

  16. Determination of reduction yield of lithium metal reduction process

    International Nuclear Information System (INIS)

    Choi, In Kyu; Cho, Young Hwan; Kim, Taek Jin; Jee, Kwang Young

    2004-01-01

    Metal reduction of spent oxide fuel is the first step for the effective storage of spent fuel in Korea as well as transmutation purpose of long-lived radio-nuclides. During the reduction of uranium oxide by lithium metal to uranium metal, lithium oxide is stoichiometrically produced. By determining the concentration of lithium oxide in lithium chloride, we can estimate that how much uranium oxide is converted to uranium metal. Previous method to determine the lithium oxide concentration in lithium chloride is tedious and timing consuming. This paper describe the on-line monitoring method of lithium oxide during the reduction process

  17. Determination of 230Th (Ionium) in uranium ores and wastes from uranium reprocessing. IV. Calculation of ionium separation yield

    International Nuclear Information System (INIS)

    Galiano Sedano, J. A.; Acena Barrenechea, M. L.

    1974-01-01

    For determining ionium ( 2 30Th) in minerals and uranium processing wastes by precipitation with fluorhidric acid, using lanthanum as carrier, and selective extraction with tenoytrifluoroacetone (TTA) followed by radiometric determination of the isolated nuclide, it is necessary the use of a tracer since the chemical yield of the separation ranges between wide limits. In this paper, the use of the beta-emitter 2 34Th as the most convenient tracer is discussed. Equations are derived for correcting for counting errors introduced by other thorium isotopes which are present either in the sample or in the tracer, as well as for calculating the chemical yield of the separation. These equations have been experimentally checked by ionium determinations carried out with different types of samples. (Author) 18 refs

  18. Effect of Plant Growth Promoting Rhizobacteria on Yield and Yield Components of Garlic Medicinal Plant (Allium sativum L. under the Conditions of Different Organic and Chemical Fertilizers Application

    Directory of Open Access Journals (Sweden)

    Yaser Esmaeilian

    2018-03-01

    often underestimated. Garlic is easy to grow and can be grown year-round in mild climates. Garlic cloves are used for consumption (raw and cooked or for medicinal purposes. They have a pungent characteristic, spicy flavor that mellows and sweetens considerably with cooking. Materials and Methods: In order to evaluate the effect of biofertilizers and organic and chemical fertilizers on yield and yield components of garlic (Allium sativum L., a split plot experiment based on RCBD with three replications was conducted in 2015-2016 growing seasons, in Gonabad University, Iran. Main plot included different organic and chemical fertilizers (1- vermicompost, 2- cow manure, 3- chemical fertilizer and 4- control and sub plot included plant growth promoting rhizobacteria (nitroxin, biophosphorous and control. In order to determine physic-chemical properties of soil, sampling was performed at the depth of 0 to 30 cm. Before cultivation, 7 and 30 t.ha-1 vermicompost and cow manure were added to the soil, respectively. Nutrient requirement of garlic for nitrogen, phosphorous and potassium from the chemical source was considered 40, 50 and 60 kg.ha-1. For application of biofertilizers, bulblets inoculated with plant growth promoting rhizobacteria for 15 minutes. Distance in and between rows was considered 10 and 20 cm, respectively. Weeds were controlled manually three times. At the end of the growing season, economic yield, biological yield, plant height, shoot dry weight, bulb diameter, bulblet weight per plant, bulblet volume per plant and bulblet number per plant were measured. Analysis of data variance was performed by using SAS software (Ver 9.1. Results and Discussion: The results showed that simple effect of chemical fertilizer on bulb diameter was not significant but combined application of chemical fertilizer and biophosphorous increased bulb diameter as much as 18% compared to control. Combined application of nitroxin and cow manure increased bulblet weight per plant by 41

  19. High yield fabrication of chemically reduced graphene oxide field effect transistors by dielectrophoresis

    International Nuclear Information System (INIS)

    Joung, Daeha; Chunder, A; Zhai, Lei; Khondaker, Saiful I

    2010-01-01

    We demonstrate high yield fabrication of field effect transistors (FET) using chemically reduced graphene oxide (RGO) sheets. The RGO sheets suspended in water were assembled between prefabricated gold source and drain electrodes using ac dielectrophoresis. With the application of a backgate voltage, 60% of the devices showed p-type FET behavior, while the remaining 40% showed ambipolar behavior. After mild thermal annealing at 200 deg. C, all ambipolar RGO FET remained ambipolar with increased hole and electron mobility, while 60% of the p-type RGO devices were transformed to ambipolar. The maximum hole and electron mobilities of the devices were 4.0 and 1.5 cm 2 V -1 s -1 respectively. High yield assembly of chemically derived RGO FET will have significant impact in scaled up fabrication of graphene based nanoelectronic devices.

  20. Effect of mass loss on the chemical yields from massive stars

    Energy Technology Data Exchange (ETDEWEB)

    Chiosi, C; Caimmi, R [Padua Univ. (Italy). Istituto di Astronomia

    1979-01-01

    Recent results on the calculation of the chemical yields from massive stars, are rediscussed by taking into account the occurrence of mass loss by stellar wind during the core H- and He-burning phases. The new yields are found to be compatible with the observed distribution of chemical abundances in the solar system, except for He. The net enrichment of several elements over the galaxy's lifetime is found to be consistent with the current estimate of the star formation rate, if we adopt a two phase process of galaxy formation (halodisk). The relative He to heavy element enrichment rate ..delta..Y/..delta..Z turns out to agree with the observational value when mass loss by stellar wind is taken into account.

  1. Root-induced Changes in the Rhizosphere of Extreme High Yield Tropical Rice: 2. Soil Solution Chemical Properties

    Directory of Open Access Journals (Sweden)

    Mitsuru Osaki

    2012-09-01

    Full Text Available Our previous studies showed that the extreme high yield tropical rice (Padi Panjang produced 3-8 t ha-1 without fertilizers. We also found that the rice yield did not correlate with some soil properties. We thought that it may be due to ability of root in affecting soil properties in the root zone. Therefore, we studied the extent of rice root in affecting the chemical properties of soil solution surrounding the root zone. A homemade rhizobox (14x10x12 cm was used in this experiment. The rhizobox was vertically segmented 2 cm interval using nylon cloth that could be penetrated neither root nor mycorrhiza, but, soil solution was freely passing the cloth. Three soils of different origins (Kuin, Bunipah and Guntung Papuyu were used. The segment in the center was sown with 20 seeds of either Padi Panjang or IR64 rice varieties. After emerging, 10 seedlings were maintained for 5 weeks. At 4 weeks after sowing, some chemical properties of the soil solution were determined. These were ammonium (NH4+, nitrate (NO3-, phosphorus (P and iron (Fe2+ concentrations and pH, electric conductivity (EC and oxidation reduction potential (ORP. In general, the plant root changed solution chemical properties both in- and outside the soil rhizosphere. The patterns of changes were affected by the properties of soil origins. The release of exudates and change in ORP may have been responsible for the changes soil solution chemical properties.

  2. Processing yield and chemical composition of rainbow trout (Oncorhynchus mykiss with regard to body weight

    Directory of Open Access Journals (Sweden)

    Maria Luiza Rodrigues de Souza

    2015-05-01

    Full Text Available The influence of weight (W category of the rainbow trout on processing yield and chemical composition of the entire eviscerated fish and fish fillet was analyzed. A completely randomized design was employed for processing variables (W1 = 300 to 370 g and W2 = 371 to 440 coupled to a 2 x 2 factorial scheme for the chemical composition (W1 and W2 and forms of presentation: fillet and whole eviscerated fish. W1 showed higher yield for entire eviscerated fish (83.00% and head (13.27%, but a lower yield for the viscera (17.00%, when compared to W2. We did not affect abdominal muscle yield, fillet with or without skin, skin percentage and residues. There were significant differences between W for moisture (W1 = 72.30% and W2 = 71.15% and lipids (CP1 = 7.96% and CP2 = 9.04% rates. Fillet moisture contents (73.74% and crude protein (19.05% were higher (p < 0.01 than for entire eviscerated fish (69.71% and 17.81%, respectively. Ash (2.15% and lipid (10.48% rates were higher (p < 0.01 for entire fish when compared to those of fillets (1.16% and 6.52%, respectively. The slaughter of fish weighing between 300 and 370 g and their fillets are more adequate for the market.

  3. Yield of Peas Treated with Compost and Chemical Fertilizer Using 15N Technique

    International Nuclear Information System (INIS)

    El-Degwy, S.M.A.

    2011-01-01

    A field experiment was carried out to evaluate the yield of peas treated with organic compost and mineral N fertilizer under sandy soil conditions. The obtained results showed that all the tested vegetative growth parameters, i.e. fresh and dry weight of leaves, root and pods of pea plants, were significantly increased with increasing the levels of mineral N fertilizer from 20 up to 50 kg N ha-1 either solely or in combination with compost. Nitrogen, phosphorus and potassium uptake by pea plants were ranked as follow: chemical N fertilize > compost + chemical N fertilize > compost. Organic additives either alone or in combination with chemical fertilizer had enhanced Ndff uptake by pods over aerial parts and roots while reversible trend was noticed with sole application of chemical fertilizer. Nitrogen derived from compost (Ndfc) and uptake by aerial parts followed by pods were enhanced by addition of organic plus chemical fertilizers comparable to sole addition of organic compost. In other term, chemical fertilizer had enhanced the portion of N derived from organic compost

  4. Evaluation of Yield and Yield Components of Oilseed Rape in the Wheat-Oilseed Rape Strip Intercropping Influenced by Chemical and Biological Fertilizers

    Directory of Open Access Journals (Sweden)

    R Amirmardfar

    2015-01-01

    Full Text Available To evaluate the effects of wheat (Triticum aestivum and oilseed rape (Brassica napus strip intercropping on yield components, seed and biological yields of oilseed rape, field experiments were carried out as factorial based on randomized complete block design with three replications at Research Farm of Tabriz University, Tabriz, Iran during 2010-2012 cropping seasons. The first factor consisted of four types of wheat and oilseed rape cropping system, sole crop of oilseed rape (A1,: strip intercropping with 8:3 (A2, 12:4 (A3 and 16:5 (A4 of wheat and oilseed rape rows, respectively and the other factor consisted of two fertilizer levels, B1: 100% chemical fertilizers (urea and triple superphosphate and B2: 50% chemical fertilizers + biofertilizers (Nitrazhin and Barvar2. The results showed that strip intercropping of wheat- oilseed rape resulted in significant increase in yield components, seed yield per occupied unit area and biological yield per occupied unit area of oilseed rape as compared with mono-cropping. The number of silique per plant in intercropping systems was significantly higher than that of mono-cropping. The highest seed yield was obtained in the 16:5 rows of wheat-oilseed rape with 343.76 g.m-2 and the lowest mean was observed in mono-cropping of oilseed rape with 260.21 g.m-2. Biological yield per occupied unit area and seed yield per intercropped unit area in B1 were significantly greater than that of B2, but this treatment had no significant effect on the other traits. Because, B1 and B2 had no significant difference in seed yield per occupied unit area and due to the importance of reduction in chemical fertilizers consumption and food and environmental health care, strip intercropping of wheat-oilseed rape under 50% chemical fertilizers + biofertilizers can be recommended as a suitable cultural method.

  5. Resolving uncertainty in chemical speciation determinations

    Science.gov (United States)

    Smith, D. Scott; Adams, Nicholas W. H.; Kramer, James R.

    1999-10-01

    Speciation determinations involve uncertainty in system definition and experimentation. Identification of appropriate metals and ligands from basic chemical principles, analytical window considerations, types of species and checking for consistency in equilibrium calculations are considered in system definition uncertainty. A systematic approach to system definition limits uncertainty in speciation investigations. Experimental uncertainty is discussed with an example of proton interactions with Suwannee River fulvic acid (SRFA). A Monte Carlo approach was used to estimate uncertainty in experimental data, resulting from the propagation of uncertainties in electrode calibration parameters and experimental data points. Monte Carlo simulations revealed large uncertainties present at high (>9-10) and low (monoprotic ligands. Least-squares fit the data with 21 sites, whereas linear programming fit the data equally well with 9 sites. Multiresponse fitting, involving simultaneous fluorescence and pH measurements, improved model discrimination. Deconvolution of the excitation versus emission fluorescence surface for SRFA establishes a minimum of five sites. Diprotic sites are also required for the five fluorescent sites, and one non-fluorescent monoprotic site was added to accommodate the pH data. Consistent with greater complexity, the multiresponse method had broader confidence limits than the uniresponse methods, but corresponded better with the accepted total carboxylic content for SRFA. Overall there was a 40% standard deviation in total carboxylic content for the multiresponse fitting, versus 10% and 1% for least-squares and linear programming, respectively.

  6. Yield and Chemical Composition of Cucumber Treated by Nitrogen Levels and Doses of Gamma Rays

    International Nuclear Information System (INIS)

    Fath El-Bab, T.Sh.; Abo El-Khier, Om.M.; Abdallah, A.A.G.

    2013-01-01

    Two field experiments were performed at the Atomic Energy Authority, Experimental farm, Inshas, Egypt during 2010 and 2011 summer growing seasons in sandy soil. The experiments were conducted to study the effect of pre-sowing seeds which treated by gamma irradiation with different doses of 0, 2, 4 and 6 Gy. This was in combination with three rates of nitrogen, fertilizer i.e., 30, 60 and 90 Kg N/fed. The experiments were laid out using drip irrigation system. The obtained results indicated that gamma rays doses showed significant differences on cucumber yield per plot or per Fed., increasing doses of gamma rays gradually increased cucumber yield per plot up to highest dose, i.e., (6 Gy). The highest value of total yield was obtained with the highest nitrogen rate (90 Kg N/fed.). Doses of gamma rays significantly increased total soluble solids (T.S.S.), total Carbohydrates, fats, total protein, NPK and Ca of cucumber fruits. Application of 60 Kg N/fed. recorded the highest values of all above mentioned chemical characters except of total protein with 90 kg N/fed. every all dose treatments. The effect of interaction between doses and fertilizer levels on chemical characters were significant therefore, the highest values was found at 4 Gy and 60 Kg N/fed. treatment for protein, fat, nitrogen and potassium contents while the carbohydrate and calcium contents had the highest value with the treatment of 6 Gy and 60 Kg N/fed

  7. Effects of organic manure on soil chemical properties and yield of ...

    African Journals Online (AJOL)

    The experiment was conducted during the 1999 cropping season at University of Agriculture, Makurdi, Nigeria to determine the effects of organic manure on the yield components of ginger. There were five treatments, namely, two levels of cow dung (15t and 30t ha-1) and two levels of Poultry litter (10t and 20t ha-1). Organic ...

  8. Effect of Chemical Fertilizer, Cow Manure and Municipal Compost on Yield, Yield Components and Oil Quantity of three Sesame (Sesamum indicum L. Cultivars in Mashhad

    Directory of Open Access Journals (Sweden)

    P Rezvani Moghaddam

    2013-10-01

    Full Text Available In order to evaluate the effects of different organic and chemical fertilizers on yield, yield components and seed oil content of sesame an experiment was conducted in a split plot layout based on randomized complete block design with four replications at Research Station, Faculty of Agriculture, Ferdowsi University of Mashhad in year 2006. Four types of fertilizer, including chemical fertilizer, cow manure, municipal compost and no fertilizer (control were allocated as main plots and three sesame cultivars (two local varieties of Kalat and Esfarayen, and Oltan cultivar were used as sub plots. The results showed that fertilizer treatments had significant effect (P

  9. Red cabbage yield, heavy metal content, water use and soil chemical characteristics under wastewater irrigation.

    Science.gov (United States)

    Tunc, Talip; Sahin, Ustun

    2016-04-01

    The objective of this 2-year field study was to evaluate the effects of drip irrigation with urban wastewaters reclaimed using primary (filtration) and secondary (filtration and aeration) processes on red cabbage growth and fresh yield, heavy metal content, water use and efficiency and soil chemical properties. Filtered wastewater (WW1), filtered and aerated wastewater (WW2), freshwater and filtered wastewater mix (1:1 by volume) (WW3) and freshwater (FW) were investigated as irrigation water treatments. Crop evapotranspiration decreased significantly, while water use efficiency increased under wastewater treatments compared to FW. WW1 treatment had the lowest value (474.2 mm), while FW treatments had the highest value (556.7 mm). The highest water use efficiency was found in the WW1 treatment as 8.41 kg m(-3), and there was a twofold increase with regard to the FW. Wastewater irrigation increased soil fertility and therefore red cabbage yield. WW2 treatment produced the highest total fresh yield (40.02 Mg ha(-1)). However, wastewater irrigation increased the heavy metal content in crops and soil. Cd content in red cabbage heads was above the safe limit, and WW1 treatment had the highest value (0.168 mg kg(-1)). WW3 treatment among wastewater treatments is less risky in terms of soil and crop heavy metal pollution and faecal coliform contamination. Therefore, WW3 wastewater irrigation for red cabbage could be recommended for higher yield and water efficiency with regard to freshwater irrigation.

  10. FORAGE YIELD, CHEMICAL COMPOSITION AND IN VITRO GAS PRODUCTION OF YELLOW HYBRID MAIZE GROWN IN MEXICO

    Directory of Open Access Journals (Sweden)

    Lizbeth Esmeralda Roblez Jimenez

    2017-12-01

    Full Text Available Maize is the most important forage in feed cattle, due to its higher energy content, however, it is characterized by its wide range of varieties and the possibility of generating a large quantity of final products. The objective of the present study was to evaluate and compare the forage yield, chemical composition and in vitro gas production as fresh and hay of a local yellow criollo maize and six varieties of yellow hybrid maize (HIT13, CML460, PIONER, COPPER, CDMO80001 and CLO80902. Fresh and dry yield did not show differences between treatments (P>0.05, their chemical composition (g / kg DM showed differences (P ˂ 0.05 for the protein content by various storage methods ranging from 59.87 to 59.61 g kg-1 DM per conservation method, NDF ranged from 591 to 686 g kg-1 DM by variety and by the method ranged from 619 to 639 g kg -1 DM, ADF ranged from 298 to 345 g kg-1 DM by variety and 317 to 340 g kg-1 DM by conservation method; ADL ranged from 58 to 41 g kg-1 DM by variety and 41 to 57 g kg-1 DM by conservation method, in vitro gas production  there were no differences (P>0.05 between varieties and conservation method. It is concluded that according to the results obtained, the varieties studied show the same forage yields in both hay and fresh, chemical composition, and in vitro gas production.

  11. Inflow, Outflow, Yields, and Stellar Population Mixing in Chemical Evolution Models

    International Nuclear Information System (INIS)

    Andrews, Brett H.; Weinberg, David H.; Schönrich, Ralph; Johnson, Jennifer A.

    2017-01-01

    Chemical evolution models are powerful tools for interpreting stellar abundance surveys and understanding galaxy evolution. However, their predictions depend heavily on the treatment of inflow, outflow, star formation efficiency (SFE), the stellar initial mass function, the SN Ia delay time distribution, stellar yields, and stellar population mixing. Using flexCE, a flexible one-zone chemical evolution code, we investigate the effects of and trade-offs between parameters. Two critical parameters are SFE and the outflow mass-loading parameter, which shift the knee in [O/Fe]–[Fe/H] and the equilibrium abundances that the simulations asymptotically approach, respectively. One-zone models with simple star formation histories follow narrow tracks in [O/Fe]–[Fe/H] unlike the observed bimodality (separate high- α and low- α sequences) in this plane. A mix of one-zone models with inflow timescale and outflow mass-loading parameter variations, motivated by the inside-out galaxy formation scenario with radial mixing, reproduces the two sequences better than a one-zone model with two infall epochs. We present [X/Fe]–[Fe/H] tracks for 20 elements assuming three different supernova yield models and find some significant discrepancies with solar neighborhood observations, especially for elements with strongly metallicity-dependent yields. We apply principal component abundance analysis to the simulations and existing data to reveal the main correlations among abundances and quantify their contributions to variation in abundance space. For the stellar population mixing scenario, the abundances of α -elements and elements with metallicity-dependent yields dominate the first and second principal components, respectively, and collectively explain 99% of the variance in the model. flexCE is a python package available at https://github.com/bretthandrews/flexCE.

  12. Inflow, Outflow, Yields, and Stellar Population Mixing in Chemical Evolution Models

    Energy Technology Data Exchange (ETDEWEB)

    Andrews, Brett H. [PITT PACC, Department of Physics and Astronomy, University of Pittsburgh, Pittsburgh, PA 15260 (United States); Weinberg, David H.; Schönrich, Ralph; Johnson, Jennifer A., E-mail: andrewsb@pitt.edu [Department of Astronomy, The Ohio State University, 140 West 18th Avenue, Columbus, OH 43210 (United States)

    2017-02-01

    Chemical evolution models are powerful tools for interpreting stellar abundance surveys and understanding galaxy evolution. However, their predictions depend heavily on the treatment of inflow, outflow, star formation efficiency (SFE), the stellar initial mass function, the SN Ia delay time distribution, stellar yields, and stellar population mixing. Using flexCE, a flexible one-zone chemical evolution code, we investigate the effects of and trade-offs between parameters. Two critical parameters are SFE and the outflow mass-loading parameter, which shift the knee in [O/Fe]–[Fe/H] and the equilibrium abundances that the simulations asymptotically approach, respectively. One-zone models with simple star formation histories follow narrow tracks in [O/Fe]–[Fe/H] unlike the observed bimodality (separate high- α and low- α sequences) in this plane. A mix of one-zone models with inflow timescale and outflow mass-loading parameter variations, motivated by the inside-out galaxy formation scenario with radial mixing, reproduces the two sequences better than a one-zone model with two infall epochs. We present [X/Fe]–[Fe/H] tracks for 20 elements assuming three different supernova yield models and find some significant discrepancies with solar neighborhood observations, especially for elements with strongly metallicity-dependent yields. We apply principal component abundance analysis to the simulations and existing data to reveal the main correlations among abundances and quantify their contributions to variation in abundance space. For the stellar population mixing scenario, the abundances of α -elements and elements with metallicity-dependent yields dominate the first and second principal components, respectively, and collectively explain 99% of the variance in the model. flexCE is a python package available at https://github.com/bretthandrews/flexCE.

  13. Impact of humic acid and chemical fertilizer application on growth and grain yield of rainfed wheat (triticum aestivum l.)

    International Nuclear Information System (INIS)

    Khan, R.U.; Khan, M.S.

    2010-01-01

    The high cost of inorganic fertilizer, use of natural fertilizer resources for increasing crop production on sustainable basis has become imperative. Two field experiments were conducted to study the potential of humic acid (HA) as a low-cost natural fertilizer and to determine its effect on the yield of rainfed wheat crop (Triticum aestivum L. cv. Naseer) at the research farm of Arid Zone Research Institute, Dera Ismail Khan during two successive winter seasons, 2007-08 and 2008-09. The treatments consisted of HA alone (3 kg ha/sup -1/ or 1.5 kg ha/sup -1/) and in combination with full (60:40 kg ha/sup -1/) and half (30:20 kg ha/sup -1/) the recommended rates of NP fertilizers. Results showed that in the first growing season (2007-08), the combination of 3 kg ha/sup -1/ HA with half (30:20 kg ha-1) rate of NP produced the highest grain yield (1314 kg ha/sup -1/) and increased the yield by 46.9% over the control. In the second growing season (2008-09), application of 3 kg ha/sup -1/ HA alone produced significantly (P<0.05) higher grain yield (2999.9 kg ha/sup -1/) and increased the yield by 24% over the control and saved 100% cost of the chemical fertilizer. Results suggested that HA applied alone at 3 kg ha/sup -1/ or in combination with half (30:20 kg ha/sup -1/) rate of NP fertilizers appeared to be the most economical rate to obtain the maximum yield of wheat under the rainfed conditions of Dera Ismail Khan. HA has great potential as a low cost natural fertilizer to improve soil fertility on sustainable basis. (author)

  14. Evaluation of Yield and Chemical Characteristics of some Peanut Mutants Induced by Gamma Irradiation

    International Nuclear Information System (INIS)

    Abd El-daem, G.A.; Anwar, M.M.

    2013-01-01

    This study was conducted to evaluate some promising mutants in peanut for yielding ability over three generation (M5, M6 and M7) and to evaluate yield attributes as will as chemical characteristics of these mutants in M7 generation induced by 100 Gy gamma radiation. The obtained results showed that the increase of yield / plot over three generation as a percentage of control was 5% for mutant 7, 10.2 % for mutant 10; 22% for mutant 9 and 22.9% for mutant 8. This increase in yield may be due to increase of one or more of yield attributes for most mutant lines. The significant increase for. No .of pods and seeds/ plant, weight of pods and seeds/ plant and 100- seed weight in M7 as compared to the control. For saturated fatty acid composition, results revealed that total saturated fatty acids ranged from 17.79% for mutant 8 to 21.75 for mutant 2 compared to 24.21% for control. Reduction of total saturated fatty acid was noticed for different mutants compared to that of the original variety. However, for total unsaturated fatty acids, results indicated that total unsaturated fatty acid composition ranged from 77.95% for mutant 9 to 82.09% for mutant 8 compared to 75.49% for control. Higher total unsaturated fatty acids for all mutant lines were obtained than that of the control, however, total saturated (TS)/ total unsaturated (TU) ratio was decreased for all mutants compared to control. The physical and chemical contents of Peanut oils showed that the refractive indices were ranged from 1.4620 to 1.4718 specific gravity were in range of 0.9146 to 0.9177. Acid value was range from 0.54 to 0.89% lodine value was ranged from 94.56 to 101.85. Saponification value was ranged from 185.2 to 190.7 and unsaponifiable matter was ranged from 0.98 to 1.33. The peroxide values ranged from 1.15 to 2.33 meq/kg oil. Also, fortified yoghurt made with replaced mutant peanut oil by 50% as milk fat substitute. Data showed that chemical composition and organolyptic properties had the

  15. On a new method to determine the yield stress in lubricating grease

    NARCIS (Netherlands)

    Cyriac, F.; Lugt, Pieter Martin; Bosman, Rob

    2015-01-01

    An experimental study using both a controlled stress and a controlled strain rheometer has been undertaken to characterize lubricating grease in shear, creep, stress relaxation, and oscillatory flow, with a main focus on determining the yield stress. The yield stress was examined using a cone–plate

  16. Determination of yields of gaseous products of carbohydrates radiolysis by mass spectrometry method. [. gamma. rays

    Energy Technology Data Exchange (ETDEWEB)

    Ivko, A A; Gol' din, S I; Bondarenko, N T; Markevich, S V; Sharpatii, V A [AN SSSR, Moscow. Inst. Khimicheskoj Fiziki

    1977-01-01

    Possible complications are treated involved in the mass spectral study of the radiolytic products of deuterated carbohydrates. A method is proposed suitable for the evaluation of hydrogen isotopes relations and the content of deuterium in water. It has been possible to identify the major gaseous radiolytic products of glucose, polyglucan and dextran, and also to assess their radiation-chemical yields.

  17. Determination of yields of gaseous products of carbohydrates radiolysis by mass spectrometry method

    International Nuclear Information System (INIS)

    Ivko, A.A.; Gol'din, S.I.; Bondarenko, N.T.; Markevich, S.V.; Sharpatyj, V.A.

    1977-01-01

    Possible complications are treated involved in the mass spectral study of the radiolytic products of deuterated carbohydrates. A method is proposed suitable for the evaluation of hydrogen isotopes relations and the content of deuterium in water. It has been possible to identify the major gaseous radiolytic products of glucose, polyglucan and dextran, and also to assess their radiation-chemical yields [ru

  18. Diversity in chemical composition and yield of essential oil from two Iranian landraces of sweet basil

    Directory of Open Access Journals (Sweden)

    Ghasemi Pirbalouti Abdollah

    2014-01-01

    Full Text Available Ocimum basilicum L. belongs to the family Lamiaceae is an herb that is extensively cultivated in some countries. Areal parts, especially leaves of sweet basil are widely used to enhance the flavour of foods such as salads, pasta, tomato products, vegetables, pizza, meat, soups, marine foods, confectioneries and other products. Essential oil yield and chemical components of two Iranian landraces of sweet basil including “Purple” and “Green” grown south-central of Iran (Isfahan province were investigated. The hydro-distillated oils were analyzed by GC-MS. The oil yields were obtained from the aerial of Purple with 0.56 ml/100 g dry matter and the aerial of Green with 0.48 ml/100 g dry matter. Results indicated significant differences (p < 0.01 among the aerial for the main constituents in the essential oil from two Iranian landraces of sweet basil. The major constituents of the essential oil from the aerial of Purple landrace were methyl chavicol or estragol (63.32% and linalool (7.96%. The main compositions of the essential oil from the aerial of Green landrace were methyl chavicol (31.82%, geranial (24.60% and neral (22.65%. Genarlly, a comparison of our results with the previous reports suggests differences in the essential oil compositions and oil yield of the plant material could be attributed to genetic diversity in two Iranian landraces of sweet basil.

  19. Determination of electroless deposition by chemical nickeling

    Directory of Open Access Journals (Sweden)

    M. Badida

    2013-07-01

    Full Text Available Increasing of technical level and reliability of machine products in compliance with the economical and ecological terms belongs to the main trends of the industrial development. During the utilisation of these products there arise their each other contacts and the interaction with the environment. That is the reason for their surface degradation by wear effect, corrosion and other influences. The chemical nickel-plating allows autocatalytic deposition of nickel from water solutions in the form of coherent, technically very profitable coating without usage of external source of electric current. The research was aimed at evaluating the surface changes after chemical nickel-plating at various changes of technological parameters.

  20. The impact of lignin downregulation on alfalfa yield, chemical composition, and in vitro gas production.

    Science.gov (United States)

    Getachew, Girma; Laca, Emilio A; Putnam, Daniel H; Witte, Dave; McCaslin, Mark; Ortega, Kara P; DePeters, Edward J

    2018-02-06

    Lignin is a complex, phenolic polymer found in plant cell walls that is essential for mechanical support, water and mineral transport, and defense in vascular plants. Over ten different enzymes play a role in the synthesis of lignin in plants. Suppression of any one enzyme or combinations of these enzymes may change the concentration and composition of lignin in the genetically transformed plants. Two lines of alfalfa that were downregulated for caffeoyl coenzyme A O-methyltransferase were used to assess the impact of lignin downregulation on chemical composition and fermentation rate and extent using an in vitro gas production technique. A total of 64 samples consisting of two reduced lignin (RL) and two controls (CL), four field replicates, two cutting intervals (CIs; 28 and 35 days), and two cuts (Cut-1 and Cut-3) were used. No differences were detected in yield, crude protein, neutral detergent fiber (aNDF), and acid detergent fiber between the lines when harvested at the 28-day CI. The acid detergent lignin (ADL) concentration in RL alfalfa lines was significantly (P gas production and metabolizable energy content were greater in RL than in CL alfalfa. RL lines had 3.8% indigestible aNDF per unit ADL, whereas CL had 3.4% (P < 0.01). The positive effect of lignin downregulation was more pronounced when intervals between harvests were longer (35-day CI compared with the 28-day CI). Lignin downregulation in alfalfa offers an opportunity to extend harvesting time (CI) for higher yield without compromising the nutritional quality of the alfalfa forage for dairy and livestock feeding. However, the in vitro results reported here warrant further study using in vivo methods. © 2018 Society of Chemical Industry. © 2018 Society of Chemical Industry.

  1. Effect of Different Methods of Chemical Weed Control Irrigation Regimes on Weed Biomass and Safflower Yield

    Directory of Open Access Journals (Sweden)

    M. Matinfar

    2011-06-01

    Full Text Available In order to investigate the effects of different weed control methods and moisture regimes on safflower (Carthamus tinctorius, a field split plot experiment based on randomized complete block design with 4 replications was conducted in Takestan Iran, during growing seasons of 2007-8. Three irrigations regimes (normal irrigation, restricted irrigation at stem elongation and restricted irrigation at  flowering stage were assigned to the main plots and nine chemical weed control method (complete hand weeding, treflan with 2 L/ha as pre plant herbicide, sonalan with 3 L/ha ad pre plant herbicide, estomp with 3 L/ha as pre plant herbicide, gallant super with 0/75 L/ha as post emergence herbicide, treflan with 2 L/ha as pre plant herbicide+ gallant super with 0/75 L/ha as post emergence herbicide, sonalan with 3 L/ha as pre plant herbicide + gallant super with 0/75 L/ha as post emergence herbicide estomp with 3 L/ha as pre plant herbicide + gallant super with 0/75 L/ha as post emergence herbicide and without hand weeding to sub- plots. At the end of growing period traits like number of head   per plant, number of seed per head, 1000 grain weight, percent of seed oil, yield of seed oil and grain yield were measured. Results indicated that treflan + gallant super treatment in restricted irrigation at stem elongation stage had the lowest dry weight of weeds. In this study maximum grain yield (2927 Kg/ha was achieved from hand weeding + usual irrigation treatments. In general treflan + gallant super treatment was the most effective treatment on safflower yield and weed control.

  2. Radiation chemical yields for formation of molecular hydrogen in alcohols based on the cyclohexane ring

    International Nuclear Information System (INIS)

    Val'ter, A.I.; Kovalev, G.V.

    1989-01-01

    Within the framework of the general problem of studying the radiolysis mechanism for alcohols based on the cyclohexane ring, we have determined the yields of molecular hydrogen in γ-irradiated cyclohexanol, 1,2-cis- and 1,2-trans-cyclohexanediols, and inositol (cyclohexanehexol). The cyclohexanol and also powders of the polyols were placed into ampuls, deaerated in a vacuum apparatus and irradiated with 60 Co γ-rays at 77 K and 293 K. After irradiation, the samples were heated up to 373 K (the polyol crystals were heated until melting) and the hydrogen evolved from the liquid phase was determined by gas chromatography

  3. 78 FR 55326 - Determinations Regarding Use of Chemical Weapons in Syria Under the Chemical and Biological...

    Science.gov (United States)

    2013-09-10

    ... DEPARTMENT OF STATE [Public Notice 8460] Determinations Regarding Use of Chemical Weapons in Syria Under the Chemical and Biological Weapons Control and Warfare Elimination Act of 1991 AGENCY: Bureau of... Government has determined on August 2, pursuant to Section 306(a) of the Chemical and Biological Weapons...

  4. Association of total-mixed-ration chemical composition with milk, fat, and protein yield lactation curves at the individual level

    NARCIS (Netherlands)

    Caccamo, M.; Veerkamp, R.F.; Licitra, G.; Petriglieri, R.; Terra, La F.; Pozzebon, A.; Ferguson, J.D.

    2012-01-01

    The objective of this study was to examine the effect of the chemical composition of a total mixed ration (TMR) tested quarterly from March 2006 through December 2008 for milk, fat, and protein yield curves for 27 herds in Ragusa, Sicily. Before this study, standard yield curves were generated on

  5. Determination of low-energy ion-induced electron yields from thin carbon foils

    International Nuclear Information System (INIS)

    Allegrini, Frederic; Wimmer-Schweingruber, Robert F.; Wurz, Peter; Bochsler, Peter

    2003-01-01

    Ion beams crossing thin carbon foils can cause electron emission from the entrance and exit surface. Thin carbon foils are used in various types of time-of-flight (TOF) mass spectrometers to produce start pulses for TOF measurements. The yield of emitted electrons depends, among other parameters, on the energy of the incoming ion and its mass, and it has been experimentally determined for a few projectile elements. The electron emission yield is of great importance for deriving abundance ratios of elements and isotopes in space plasmas using TOF mass spectrometers. We have developed a detector for measuring ion-induced electron yields, and we have extended the electron yield measurements for oxygen to energies relevant for solar wind research. We also present first measurements of the carbon foil electron emission yield for argon and iron in the solar wind energy range

  6. Comparison of different methods for extraction from Tetraclinis articulata: yield, chemical composition and antioxidant activity.

    Science.gov (United States)

    Herzi, Nejia; Bouajila, Jalloul; Camy, Séverine; Romdhane, Mehrez; Condoret, Jean-Stéphane

    2013-12-15

    In the present study, three techniques of extraction: hydrodistillation (HD), solvent extraction (conventional 'Soxhlet' technique) and an innovative technique, i.e., the supercritical fluid extraction (SFE), were applied to ground Tetraclinis articulata leaves and compared for extraction duration, extraction yield, and chemical composition of the extracts as well as their antioxidant activities. The extracts were analyzed by GC-FID and GC-MS. The antioxidant activity was measured using two methods: ABTS(•+) and DPPH(•). The yield obtained using HD, SFE, hexane and ethanol Soxhlet extractions were found to be 0.6, 1.6, 40.4 and 21.2-27.4 g/kg respectively. An original result of this study is that the best antioxidant activity was obtained with an SFE extract (41 mg/L). The SFE method offers some noteworthy advantages over traditional alternatives, such as shorter extraction times, low environmental impact, and a clean, non-thermally-degraded final product. Also, a good correlation between the phenolic contents and the antioxidant activity was observed with extracts obtained by SFE at 9 MPa. Copyright © 2013 Elsevier Ltd. All rights reserved.

  7. Use of abrupt strain path change for determining subsequent yield surface

    DEFF Research Database (Denmark)

    Kuroda, Mitsutoshi; Tvergaard, Viggo

    1999-01-01

    is prescribed, which makes the stress point move quickly along the yield surface. It is assumed that a closed-loop testing machine is used for the experiment, so that the strain path can be prescribed according to strain gauge measurements. Relative to the standard method of determining yield surface shapes...... by probing in many different stress directions from the elastic region, using some chosen plastic strain offset, the main advantage of the proposed method is that elastic unloading is not needed prior to tracing the yield surface. The method is illustrated here by a few analyses, first for the simplest how...

  8. Yield strengths of tungsten-base composites determined from bend tests

    International Nuclear Information System (INIS)

    Zukas, E.G.; Eash, D.T.

    1976-08-01

    The variation in yield strength with either strain rate or temperature was determined for a number of tungsten-base composites by use of the simple three-point bend test. The yield strengths were comparable with those obtained in standard tensile tests. Additional studies on 1019 steel, either in the as-rolled or annealed condition, gave results in agreement with handbook values, as did two aluminum alloys. These results demonstrate that the bend test deserves wider acceptance in materials testing programs

  9. Evaluation of Effect of Chemical and Organic Fertilizers on Growth Characteristics, Yield and Yield components of three Sesame Ecotypes (Sesamum indicum L.

    Directory of Open Access Journals (Sweden)

    M Goldani

    2014-07-01

    Full Text Available Using organic fertilizers is cause increase soil fertility, improving crop growth and production. For this purpose a greenhouse experiment was carried out in factorial arrangement based on a completely randomized design with three replications during 2011 year. First factor included: three sesame ecotype (MSC3, MSC6, MSC7 and second factor was 6 fertilizer treatments that included: Incorporation manure and chemical fertilizer (216 g manure and 1 gram chemical fertilizer NPK, Chemical fertilizer (2 g NPK, Vermicompost (192 g, Manure ( 228 g, Compost Sulfur granules (192 g per vase and Control (without any manure or fertilizer. Results indicated that different manure treatments had significant effect on morphological and yield components traits, as the most number and length branch per plant was obtained from incorporation manure and chemical fertilizer treatment. Appling incorporation manure and chemical fertilizer treatment had the most biomass in MSC3 ecotype that in comparison of control treatment was increased almost 73 percent. Consuming incorporation manure and chemical fertilizer treatment in MSC3 ecotype was also obtained the most capsule per plant (21.2, number seed per capsule (54.4, 100-seed weight (0.257 g and seed per plant with (1.95 g. The least seed weight per plant with 0.450 g was observed in MSC7 ecotype from application of control treatment. Response of three sesame ecotype (MSC3, MSC6, MSC7 to applied vermin-compost manure was similar; as the amount of seed weight per plant was increased more than 1 g per plant in all these ecotypes and in others fertilizer treatments was not observed this trend. There was significant positive correlation between seed weight per plant and number of capsule per plant (r=0.83**, height (r=0.68** and biomass (r=0.51**. The results showed that incorporation manure and chemical fertilizer was improved on growth and yield characteristics of sesame plant.

  10. Assessing the Effect of Organic Compounds, Biofertilizers and Chemical Fertilizers on Morphological Properties,yield and Yield Components of Forage Sorghum (Sorghum bicolor

    Directory of Open Access Journals (Sweden)

    A.H Saeidnejad

    2012-12-01

    Full Text Available Recently, using the source of organic fertilizers and biofertilizers in sustainable crop production is growing. In order to evaluate the effect of organic compounds, biofertilizers and chemical fertilizer on morphological properties, yield and yield components of forage Sorghum (sorghum bicolor a field experiment was conducted in the Research Farm, College of Agriculture, Ferdowsi University of Mashhad in 2008.The treatments were seed inoculation with the combination of Azotobacter chroococcum and Azospirillum brasilense, Compost (15 t/ha, Vermicompost (10 t/ha, seed inoculation with Azotobacter and Azospirillum and compost (10t/ha, seed inoculation with Azotobacter chroococcum and Azospirillum brasilense and Vermicompost (7t/ha, seed inoculation with Pseudomonas flurescence, seed inoculation with Pseudomonas flurescence and Azotobacter chroococcum and Azospirillum brasilense combination, seed inoculation with Pseudomonas flurescence and compost (15t/ha, chemical fertilizer (80 kg/h urea fertilizer and 50 kg/h super phosphate fertilizer and control. Harvesting was performed in 2 cuts in flowering stage. Plant height, number of tiller per plant and SPAD reading was significantly affected by the treatments. Stem diameter was not affected by any treatments. There was a significant difference among all treatments in terms of fresh and dry forage yield. There were no significant differences among all treatments in terms of stem and leaf dry matter. In general, result of this experiment indicated that organic amendments and biofertilizers could be acceptable alternatives for chemical fertilizers.

  11. Effects of Chemical Fertilizer, Algea Compost and Zeolite on Green Bean Yield

    Directory of Open Access Journals (Sweden)

    Aysun Türkmen

    2017-03-01

    Full Text Available The present study used chemical fertilizer, brown algae compost and zeolite carried out in the field of Giresun Hazelnut Research Center between May-November 2014 in pots according to randomized blog design as three replicate each. Treatment groups were consist of eight different combinations as follow; G1-Control, G2-Zeolite, G3-Compost, G4-Chemical Fertilizer, G5-Zeolite+Compost, G6-Zeolite+Chemical Fertilizer, G7-Compost+ Chemical Fertilizer, G8-Compost+Zeolite+ Chemical Fertilizer. The brown algae (Cystoseira sp. were used as compost material. These combinations were applied to green beans (Phaseolus vulgaris. The green beans were seeded by hand to arrange planting depth of 5-6 cm and 20 seeds/m2. Except control group, each treatment was added fertilizers as 50 g zeolite, 50 g compost, and 25 g chemical according to treatment design. Half of the chemical fertilizers were added at seeding time and the rest after two weeks. Collected soil samples were analyzed right after harvest, the greatest values of treatment groups were determined as; Carbon% G1: 5.08, nitrogen G3: 0.09 ppm, sodium G5: 139 ppm, potassium G6 and G8: 5 ppm, magnesium G2: 1865 ppm, calcium G6: 8.33 ppm, manganese G2: 359 ppm, iron G6 : 16070 ppm, cobalt G6 and G7: 7.91 ppm, copper G2: 17.5 ppm, zinc G8: 28.0 ppm, selenium G7: 4.17 ppm, cadmium G5: 0.08 ppm, lead G4: 5.31 ppm. The greatest harvest value as g/m2 was obtained from zeolite only group G2 with 273 while the lowest was obtained from Compost only group G3 with 113 g/m2, obviously showing the effectiveness of zeolite only application moreover, also thinking that better results may get if the present study run for longer period.

  12. Effects of Organic and Chemical Fertilizers on Leaf Yield, Essential Oil Content and Composition of Lemon Verbena (Lippia citriodora Kunth

    Directory of Open Access Journals (Sweden)

    Mohammad Taghi Ebadi

    2017-02-01

    Full Text Available Introduction: Organic fertilizers with beneficial effects on soil structure and nutrient availability help maintain yield and quality, and they are less costly than synthetic fertilizers. Vermicompost and vermiwash are two organic fertilizers that they contain a biologically active mixture of bacteria, enzymes and phytohormones, also these organic fertilizers can supply the nutritional needs of plants. Lemon verbena (Lippia citriodora Kunth, Verbenaceae is an evergreen perennial aromatic plant. The lemon-scented essential oil from the lemon verbena has been widely used for its digestive, relaxing, antimalarial and lemony flavor properties. In order to decrease the use of chemical fertilizers for reduction of environmental pollution, this research was undertaken to determine effects of vermicompost and vermiwash in comparison with chemical fertilizer on leaf yield, essential oil content and composition of lemon verbena. Materials and Methods: A pot experiment based on a completely randomized design with six treatments and three replications on Lemon verbena was carried out in the experimental greenhouse of the Department of Horticulture Sciences, Tarbiat Modares University, 2012. Treatments consisted of 10, 20 and 30 % by volume of vermicompost and vermiwash (with an addition to irrigation in three steps, including: two weeks after the establishment of plants in pots, the appearing of branches and three weeks before harvest, complete fertilizer and control without any fertilizer. Each replication contained six pots and each pot contained one plant of Lemon verbena provided from Institute of Medicinal Plants, Karaj, therefore 108 pots were used in this experiment. The pots were filled up by a mixture contained 3/5 soil and 2/5 sand (v/v. After three months, plant aerial parts were harvested concomitantly at starting of the flowering stage. Aerial parts were dried at room temperature for 72 hours and dry weights of dried branches and leaves were

  13. Determination of ''226Ra by Alpha Spectrometry by Using ''225Ra as Yield Tracer

    International Nuclear Information System (INIS)

    Crespo, M. T.; Oller, O.

    1999-01-01

    A method for the determination of low-level ''226 Ra in environmental and geological samples by alpha spectrometry is described. The method is based on the use of ''225 Ra from ''229 Th as yield tracer and has been developed to analyze U, Th and Ra in the same sample. (Author) 12 refs

  14. Method for Determination of Neptunium in Large-Sized Urine Samples Using Manganese Dioxide Coprecipitation and 242Pu as Yield Tracer

    DEFF Research Database (Denmark)

    Qiao, Jixin; Hou, Xiaolin; Roos, Per

    2013-01-01

    A novel method for bioassay of large volumes of human urine samples using manganese dioxide coprecipitation for preconcentration was developed for rapid determination of 237Np. 242Pu was utilized as a nonisotopic tracer to monitor the chemical yield of 237Np. A sequential injection extraction chr...... and rapid analysis of neptunium contamination level for emergency preparedness....

  15. Determination of Chemical Constituents of the Marine Pulmonate ...

    African Journals Online (AJOL)

    Determination of Chemical Constituents of the Marine Pulmonate Slug, Paraoncidium reevesii. B Sun, H Shen, H Wu, L Yao, Z Cheng, Y Diao. Abstract. Purpose: To isolate and identify the chemical components of Paraoncidium reevesii. Methods: Silica gel column chromatography was used to isolate the components from ...

  16. A model independent determination of the B{yields}X{sub s}{gamma} decay rate

    Energy Technology Data Exchange (ETDEWEB)

    Bernlochner, Florian U. [Victoria Univ., BC (Canada); Lacker, Heiko [Humboldt-Universitaet, Berlin (Germany); Ligeti, Zoltan [California Univ., Berkeley, CA (United States). Ernest Orlando Lawrence Berkeley National Laboratory; Stewart, Iain W. [Massachusetts Institute of Technology, Cambridge, MA (United States). Center for Theoretical Physics; Tackmann, Frank J.; Tackmann, Kerstin [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany)

    2013-03-15

    The goal of the SIMBA collaboration is to provide a global fit to the available measurements of inclusive B{yields}X{sub s}{gamma} and B{yields}X{sub u}l{nu} decays. By performing a global fit one is able to simultaneously determine the relevant normalizations, i.e. the total B{yields}X{sub s}{gamma} rate and the CKM-matrix element vertical stroke Vub vertical stroke, together with the required hadronic parameters, most importantly the b-quark mass and the b-quark distribution function in the B-meson, called the shape function. In this talk, the current status on the model-independent determination of the shape function and vertical stroke C{sub 7}{sup incl}V{sub tb}V{sub ts}{sup *} vertical stroke, which parametrizes the total B{yields}X{sub s}{gamma} rate, from a global fit to the available B{yields}X{sub s}{gamma} measurements from Babar and Belle is presented. In particular, the theoretical uncertainties originating from variations of the different factorization scales are evaluated.

  17. Determining Rheological Parameters of Generalized Yield-Power-Law Fluid Model

    Directory of Open Access Journals (Sweden)

    Stryczek Stanislaw

    2004-09-01

    Full Text Available The principles of determining rheological parameters of drilling muds described by a generalized yield-power-law are presented in the paper. Functions between tangent stresses and shear rate are given. The conditions of laboratory measurements of rheological parameters of generalized yield-power-law fluids are described and necessary mathematical relations for rheological model parameters given. With the block diagrams, the methodics of numerical solution of these relations has been presented. Rheological parameters of an exemplary drilling mud have been calculated with the use of this numerical program.

  18. Three methods to determine the yields of DNA double-strand breaks

    International Nuclear Information System (INIS)

    Erzgraeber, G.; Lapidus, I.L.

    1985-01-01

    A possibility of determining the yield of DNA double-strand breaks in cells of the Chinese hamster (V79-4) by finding the amount of DNA released as a result of breaks and by determining the relative sedimentation velocity of DNA-membrane complexes affected by ionizing radiations with different physical characteristics is discussed. Results of the analysis are compared with the data obtained by a traditional method of sedimentation in the neutral sucrose density gradient. Comparative characterization of the methods is discussed. The yields of DNA double-strand breaks determined by the suggested independent methods are in good agreement, which opens possibilities of studying induction and repair of double-strand breaks by means of simpler and more reliable methods

  19. Rapid and reliable protein structure determination via chemical shift threading.

    Science.gov (United States)

    Hafsa, Noor E; Berjanskii, Mark V; Arndt, David; Wishart, David S

    2018-01-01

    Protein structure determination using nuclear magnetic resonance (NMR) spectroscopy can be both time-consuming and labor intensive. Here we demonstrate how chemical shift threading can permit rapid, robust, and accurate protein structure determination using only chemical shift data. Threading is a relatively old bioinformatics technique that uses a combination of sequence information and predicted (or experimentally acquired) low-resolution structural data to generate high-resolution 3D protein structures. The key motivations behind using NMR chemical shifts for protein threading lie in the fact that they are easy to measure, they are available prior to 3D structure determination, and they contain vital structural information. The method we have developed uses not only sequence and chemical shift similarity but also chemical shift-derived secondary structure, shift-derived super-secondary structure, and shift-derived accessible surface area to generate a high quality protein structure regardless of the sequence similarity (or lack thereof) to a known structure already in the PDB. The method (called E-Thrifty) was found to be very fast (often chemical shift refinement, these results suggest that protein structure determination, using only NMR chemical shifts, is becoming increasingly practical and reliable. E-Thrifty is available as a web server at http://ethrifty.ca .

  20. Yield gap determinants for wheat production in major irrigated cropping zones of punjab, pakistan

    International Nuclear Information System (INIS)

    Hussain, A.; Aujla, K.M.; Badar, N.

    2014-01-01

    Yield gap is useful measurement for crop productivity and the extent to which crop productivity falls below some potential level. The study was carried out to analyze the yield gap and determinants of wheat production in the Punjab province of Pakistan. It is based on cross sectional data from 210 farmers for the crop year 2009-10. Results suggest that farm level wheat yields are less than the potential yield level by 33.0%, 43.0% and 50.6% in the mixed-cropping, cotton-wheat and rice-wheat zones of the province, respectively. Ordinary least square regression analysis of wheat production by assuming Cobb-Douglas specification reveals that the number of irrigations, usage of farm yard manure and fertilizers contribute positively and significantly to wheat crop production. Coefficients of dummy variables for cropping zones indicate that farmers in the mixed cropping zone are obtaining better yield of the wheat crop as compared to their counterparts in other selected cropping zones. These results suggested that farmers can increase wheat productivity by increasing the use of factor inputs; however, poverty may be a constraint on realizing these gains. Thus, wheat production can be increased in the country by helping resource poor farmers through suitable support mechanisms. (author)

  1. Experimental determination of the yield stress curve of the scotch pine wood materials

    Science.gov (United States)

    Günay, Ezgi; Aygün, Cevdet; Kaya, Şükrü Tayfun

    2013-12-01

    Yield stress curve is determined for the pine wood specimens by conducting a series of tests. In this work, pinewood is modeled as a composite material with transversely isotropic fibers. Annual rings (wood grain) of the wood specimens are taken as the major fiber directions with which the strain gauge directions are aligned. For this purpose, three types of tests are arranged. These are tensile, compression and torsion loading tests. All of the tests are categorized with respect to fiber orientations and their corresponding loading conditions. Each test within these categories is conducted separately. Tensile and compression tests are conducted in accordance with standards of Turkish Standards Institution (TSE) whereas torsion tests are conducted in accordance with Standards Australia. Specimens are machined from woods of Scotch pine which is widely used in boat building industries and in other structural engineering applications. It is determined that this species behaves more flexibly than the others. Strain gauges are installed on the specimen surfaces in such a way that loading measurements are performed along directions either parallel or perpendicular to the fiber directions. During the test and analysis phase of yield stress curve, orientation of strain gauge directions with respect to fiber directions are taken into account. The diagrams of the normal stress vs. normal strain or the shear stress vs. shear strain are plotted for each test. In each plot, the yield stress is determined by selecting the point on the diagram, the tangent of which is having a slope of 5% less than the slope of the elastic portion of the diagram. The geometric locus of these selected points constitutes a single yield stress curve on σ1-σ2 principal plane. The resulting yield stress curve is plotted as an approximate ellipse which resembles Tsai-Hill failure criterion. The results attained in this work, compare well with the results which are readily available in the literature.

  2. Utility of reversed phase high performance liquid chromatography for on-line yield determination of radiochemical separations: Studies with cobalt

    International Nuclear Information System (INIS)

    Subramanian, S.; Woittiez, J.R.W.

    1993-01-01

    This article indicates the potentials of high performance liquid chromatography (HPLC) as a radiochemical technique for multielement separation of neutron irradiated samples. The focus lies on the convenience to use the detector signal of the eluted components to indicate the chemical yield of the analyte, which has often proved to be a crucial step in radiochemical separations. Two signals have been utilized. The UV signal of the metal-ligand complexes separated by reversed phase HPLC and the radioactive response as a result of sample irradiation of carrier-tracer addition. Change in ratio is discussed between the two signals, if any, for a specific sample. Losses of metal as much as 65% were simulated and corrected using the individual UV response. The method promises improved accuracy for elemental analysis despite losses suffered during the various chemical steps. The procedure omits the necessity of additional analytical steps for yield determination. The present article aims at the chromatographic part of the study. Cobalt as cobalt diethyldithiocarbamate has been used to demonstrate the viability of the concept. The separation was developed on c C18 reverse phase analytical column and optimized on a semi preparative one

  3. Estimation of Corn Yield and Soil Nitrogen via Soil Electrical Conductivity Measurement Treated with Organic, Chemical and Biological Fertilizers

    Directory of Open Access Journals (Sweden)

    H. Khalilzade

    2016-02-01

    Full Text Available Introduction Around the world maize is the second crop with the most cultivated areas and amount of production, so as the most important strategic crop, have a special situation in policies, decision making, resources and inputs allocation. On the other side, negative environmental consequences of intensive consumption of agrochemicals resulted to change view concerning food production. One of the most important visions is sustainable production of enough food plus attention to social, economic and environmental aspects. Many researchers stated that the first step to achieve this goal is optimization and improvement of resources use efficiencies. According to little knowledge on relation between soil electrical conductivity and yield of maize, beside the environmental concerns about nitrogen consumption and need to replace chemical nitrogen by ecological inputs, this study designed and aimed to evaluate agroecological characteristics of corn and some soil characteristics as affected by application of organic and biological fertilizers under field conditions. Materials and Methods In order to probing the possibility of grain yield and soil nitrogen estimation via measurement of soil properties, a field experiment was conducted during growing season 2010 at Research Station, Ferdowsi University of Mashhad, Iran. A randomized complete block design (RCBD with three replications was used. Treatments included: 1- manure (30 ton ha-1, 2-vermicompost (10 ton ha-1, 3- nitroxin (containing Azotobacter sp. and Azospirillum sp., inoculation was done according to Kennedy et al., 4- nitrogen as urea (400 kg ha-1 and 5- control (without fertilizer. Studied traits were soil pH, soil EC, soil respiration rate, N content of soil and maize yield. Soil respiration rate was measured using equation 1: CO2= (V0- V× N×22 Equation 1 In which V0 is the volume of consumed acid for control treatment titration, V is of the volume of consumed acid for sample treatment

  4. The effect of application of chemical and organic fertilizers on yield and yield components of sesame (Sesamum indicum L. in different plant densities

    Directory of Open Access Journals (Sweden)

    P. Rezvani Moghaddam

    2016-04-01

    Full Text Available In order to understand the effect of plant density and different fertilizers on sesame (Sesamum indicum L. production, an experiment was conducted as a factorial arrangement based on completely randomized block design with three replications. The experimental treatments were fertilizers in four levels (cow manure (30 t.ha-1, municipal compost (30 t.ha-1, chemical fertilizer (250 kg ammonium phosphate + 100 kg urea and control (no-fertilizer and plant density in four levels (20, 30, 40 and 50 plant.m-2. The results showed that all treatments increased the plant height, number of capsule per plant, plant biomass, seed yield, seed weight and number of seed per plant compared to control, significantly. The highest amount of the traits was obtained in manure treatment. The seed yield was increased by increasing plant density, but decreased the plant height, number of capsule per plant, plant biomass, seed yield and weight and number of seed per plant, significantly. 1000-seed weight, harvest index and weight of seed per capsule had no affected by treatments. Our result indicated that the density of 40 plant.m-2 among using manure was the most appropriate of cropping pattern in our experiment.

  5. Comparison the effect of organic and chemical fertilizers on yield and essential oil percentage of Basil (Ocimum basilicum L.

    Directory of Open Access Journals (Sweden)

    S.M.K. Tahami

    2016-04-01

    Full Text Available In order to have a sustainable agriculture it is necessary to use environmental friendly inputs to improve ecological aspects of environment. Basil (Ocimum basilicum L. is a medicinal and vegetable crop which is cultivated in different parts of the world. An experiment was conducted at Research Station, Faculty of Agriculture, Ferdowsi University of Mashhad, Iran, in year 2009. A complete randomized block design with six treatments, and three replications was used. The treatments were: control (no fertilizer, cow manure, sheep manure, hen manure, vermin-compost and NPK fertilizers. Results showed that all studied organic manures were high in measured characters in compare with chemical fertilizer. The highest plant height, leaf yield, fresh and dry matter were obtained at vermicompost. Treatments have no significant affect on Essential oil percentage. The highest essential oil yield was obtained in cow manure treatments. Third cut and the first cut had the maximum and the minimum of leaf yield, fresh and dry shoot yield, respectively. Essential oil percentage in the first cut was significantly more than other cuts, but essential oil yield, were the highest in third cut because this cut produced highest leaf yield. There was no significant difference between chemical fertilizers and control treatment in all characters except green area index and fresh and dry leaf weight in a plant.

  6. Determination of Selection Index of Cocoa (Theobroma Cacao L.) Yield Traits Using Regression Methods

    OpenAIRE

    Setyawan, Bayu; Taryono; Mitrowihardjo, Suyadi

    2016-01-01

    The increasing chocolate consumption has not been followed by growing production of dry cocoa beans. In order to support the increase in cocoa production, planting materials with high yield are needed. The objective of this research was to determine the components of cocoa traits affecting weight of dry cocoa beans, and set a selection index for superior cocoa trees. The experiment material were four cocoa hybrid populations of which their family ancestry were unknown, and were planted on Sam...

  7. Determination of polysaccharide yield from the fruiting bodies and mycelium of selected mushroom species

    International Nuclear Information System (INIS)

    Shaiful Azuar Mohamad; Mat Rasol Awang

    2006-01-01

    Numerous polysaccharides and polysaccharides-protein complexes have been isolated from mushrooms and used as a source of therapeutic agents. The mycelium of Pleurotus sajor caju, Pleurotus tuber-regium, black ganoderma, and the fruiting bodies of Pleurotus sajor caju and Pleurotus florida were used to determine the percentage of polysaccharides obtained from the mushroom raw material. Hot water extraction method was used followed by refrigerated centrifuge and lyophilization. The yield from the various species will be compared. (Author)

  8. Chemical, Biological, Radiological, Nuclear, and High-Yield Explosives Consequences Management

    Science.gov (United States)

    2006-10-02

    protective measures associated with such offensive operations. Since riot control agents and herbicides are not considered to be chemical warfare agents...control. Procedures to avoid, reduce, remove, or render harmless (temporarily or permanently) nuclear, radiological, biological, and chemical...destroying, neutralizing, making harmless , or removing chemical or biological agents, or by removing radioactive material clinging to or around it. (JP 1

  9. Effect of chemical and mechanical weed control on cassava yield, soil quality and erosion under cassava cropping system

    Science.gov (United States)

    Islami, Titiek; Wisnubroto, Erwin; Utomo, Wani

    2016-04-01

    Three years field experiments were conducted to study the effect of chemical and mechanical weed control on soil quality and erosion under cassava cropping system. The experiment were conducted at University Brawijaya field experimental station, Jatikerto, Malang, Indonesia. The experiments were carried out from 2011 - 2014. The treatments consist of three cropping system (cassava mono culture; cassava + maize intercropping and cassava + peanut intercropping), and two weed control method (chemical and mechanical methods). The experimental result showed that the yield of cassava first year and second year did not influenced by weed control method and cropping system. However, the third year yield of cassava was influence by weed control method and cropping system. The cassava yield planted in cassava + maize intercropping system with chemical weed control methods was only 24 t/ha, which lower compared to other treatments, even with that of the same cropping system used mechanical weed control. The highest cassava yield in third year was obtained by cassava + peanuts cropping system with mechanical weed control method. After three years experiment, the soil of cassava monoculture system with chemical weed control method possessed the lowest soil organic matter, and soil aggregate stability. During three years of cropping soil erosion in chemical weed control method, especially on cassava monoculture, was higher compared to mechanical weed control method. The soil loss from chemical control method were 40 t/ha, 44 t/ha and 54 t/ha for the first, second and third year crop. The soil loss from mechanical weed control method for the same years was: 36 t/ha, 36 t/ha and 38 t/ha. Key words: herbicide, intercropping, soil organic matter, aggregate stability.

  10. Effect of oxidant concentration, exposure time, and seed particles on secondary organic aerosol chemical composition and yield

    Directory of Open Access Journals (Sweden)

    A. T. Lambe

    2015-03-01

    This similarity in turn suggests that both in the flow reactor and in chambers, SOA chemical composition at low OH exposure is governed primarily by gas-phase OH oxidation of the precursors rather than heterogeneous oxidation of the condensed particles. In general, SOA yields measured in the flow reactor are lower than measured in chambers for the range of equivalent OH exposures that can be measured in both the flow reactor and chambers. The influence of sulfate seed particles on isoprene SOA yield measurements was examined in the flow reactor. The studies show that seed particles increase the yield of SOA produced in flow reactors by a factor of 3 to 5 and may also account in part for higher SOA yields obtained in the chambers, where seed particles are routinely used.

  11. Yields, photosynthetic efficiencies, and proximate chemical composition of dense cultures of marine microalgae. A subcontract report

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, W.H.; Seibert, D.L.R.; Alden, M.; Eldridge, P.; Neori, A.

    1983-07-01

    The yields, photosynthetic efficiencies, and proximate composition of several microalgae were compared in dense cultures grown at light intensities up to 70% sunlight. Yields ranged from 3.4 to 21.7 g dry weight/m/sup 2/ day. The highest yield was obtained with Phaeodactylum; the lowest in Botryococcus cultures. The same species had the highest and lowest efficiencies of utilization of photosynthetically active radiation. In nitrogen-sufficient cells of all but one species, most of the dry weight consisted of protein. Lipid content of all species was 20 to 29%, and carbohydrate content 11 to 23%. Lipid content increased somewhat in N-deficient Phaeodactylum and Isochrysis cells, but decreased in deficient Monallanthus cells. Because the overall dry weight yield was reduced by deficiency, lipid yields did not increase. However, since the carbohydrate content increased to about 65% in N-deficient Dunaliella and Tetraselmis cells, the carbohydrate yield increased. In Phaeodactylum the optimum light intensity was about 40% of full sunlight. Most experimets with this alga included a CUSO/sub 4/ filter to decrease infrared irradiance. When this filter was removed, the yield increased because more red light in the photosynthetically active spectral range was included. These results should prove useful to workers attempting to maximize yields and efficiencies, but additional studies are needed. 69 references, 27 figures, 18 tables.

  12. Researches on Determination Yield and Yield Components of Some Common Vetch (Vicia sativa L. Genotypes in Ecological Conditions of Diyarbakır

    Directory of Open Access Journals (Sweden)

    Seyithan SEYDOŞOĞLU

    2014-09-01

    Full Text Available The research was conducted to determine yield and yield components of some common vetch genotypes in order to examine some of the traits, during 2011-2013 seasons in GAP International Agricultural Research and Training Center was carried out on the experimental field. In the study, a total of 20 different genotypes were used common vetch, field trials randomized block design with 3 replications was established. In the study, herbage yield, hay yield and seed yield in addition to days to %50 flowering duration, plant height, main stem length, main stem number, pod number per plant, grain number per pod as affecting yield some properties were also investigated. In both years of the study, days to %50 flowering duration and grain number per pod characteristics examined, except among genotypes for all other parameters are determined significant differences in statistical terms. According to the average of two years result; days to %50 flowering duration, plant height, main stem length, main stem number, pod number per plant, grain number per pod, herbage yield, hay yield, seed yield, 1000 seed weight were changed between 157.8-174.0 days, 33.9-62.6 cm, 52.0-83.3 cm, 1.6-2.6 number, 13.5-21.2 number, 4.7-5.6 number, 1522.0-3232.3 kg da-1, 308.0-919.5 kg da-1, 92.2-293.7 kg da-1, 46.5-84.5 g, respectively. According to these results, under the climate and soil conditions of Diyarbakır; for the grass production common vetch genotypes "D-135" was suggested and for the seed production common vetch genotypes "IFVS-715" and "GAP-59998" were suggested.

  13. Determination of radiochemical yields of 186Re-labelled complexes using thin layer chromatography

    International Nuclear Information System (INIS)

    Konirova, R.; Kohlickova, M.; Jedinakova-Krizova, V.

    1999-01-01

    The reaction conditions for synthesis of three rhenium complexes 186 Re-methylendiphosphonate (MDP), 186 Re-hydroxyethylidendiphosphonate (HEDP) and 186 Re-citrate have been investigated. Radiochemical yield of complexation has been determined by thin layer chromatography and paper chromatography. The rhenium complexation with corresponding ligand is dependent on pH values of reaction mixture, concentration of studied ligand (MDP, HEDP and sodium citrate) and concentration of reducing agent. Stannous chloride with ascorbic acid (as antioxidant) was used for reduction of perrhenate. The labeling yield of 186 Re-MDP was about 90 %, of 186 Re-HEDP more than 80 % and more than 75 % for 186 Re-citrate under optimum conditions. Besides, the possibility of application of porphyrins as organic ligands for complexation with rhenium isotopes is examined. (authors)

  14. Determination of chemical solute transport parameters effecting radiostrontium interbed sediments

    International Nuclear Information System (INIS)

    Hemming, C.; Bunde, R.L.; Rosentreter, J.J.

    1993-01-01

    The extent to which radionuclides migrate in an aquifer system is a function of various physical, chemical, and biological processes. A measure of this migration rate is of primary concern when locating suitable storage sites for such species. Parameters including water-rock interactions, infiltration rates, chemical phase modification, and biochemical reactions all affect solute transport. While these different types of chemical reactions can influence solute transport in subsurface waters, distribution coefficients (Kd) can be send to effectively summarize the net chemical factors which dictate transport efficiency. This coefficient describes the partitioning of the solute between the solution and solid phase. Methodology used in determining and interpreting the distribution coefficient for radiostrontium in well characterized sediments will be presented

  15. Understanding Emerging Market Sovereign Bond Yield Spread: Role of Default and Non-Default Determinants

    Directory of Open Access Journals (Sweden)

    Adelia Surya Pratiwi

    2015-04-01

    Full Text Available This paper is motivated by the fact that emerging market assets size has been expanding and trying to use sovereign debt market as part of capital market as main research focus. It is highlighting the distinction between default and non-default determinants and examining their significance in explaining emerging market sovereign bond yield spread. Using Cross-Sectional Fixed-Effect Panel Estimator, we found that both default (as proxied by Credit Rating and Outlook Index and non-default (as proxied by 3-month Fed Funds Futures determinants has significant explanatory power to sovereign bond yield spread. Extensively, we also found the significance to add volatility of 3-month Fed Funds Futures and Fed Target Rate basis and volatility of advanced stock markets as variables to stand for non-default determinants in the model. The significance of the latter model is strengthened by higher forecasting as well as indicates the significant role of US market to emerging market sovereign bond market.

  16. [Effects of Chemical Fertilizers and Organic Fertilizer on Yield of Ligusticum chuanxiong Rhizome].

    Science.gov (United States)

    Liang, Qin; Chen, Xing-fu; Li, Yan; Zhang, Jun; Meng, Jie; Peng, Shi-ming

    2015-10-01

    To study the effects of different N, P, K and organic fertilizer (OF) on yield of Ligusticum chuanxiong rhizome, in order to provide the theoretical foundation for the establishment of standardization cultivation techniques. The field plot experiments used Ligusticum chuanxiong rhizome which planted in Pengshan as material, and were studied by the four factors and five levels with quadratic regression rotation-orthogonal combination design. According to the data obtained, a function model which could predict the fertilization and yield of Ligusticum chuanxiong rhizome accurately was established. The model analysis showed that the yields of Ligusticum chuanxiong rhizome were significantly influenced by the N, P, K and OF applications. Among these factors, the order of increase rates by the fertilizers was K > OF > N > P; The effect of interaction between N and K, N and OF, K and OF on the yield of Ligusticum chuanxiong rhizome were significantly different. High levels of N and P, N and organic fertilizer, K and organic fertilizer were conducive to improve the yield of Ligusticum chuanxiong rhizome. The results showed that the optimal fertilizer application rates of N was 148.20 - 172.28 kg/hm2, P was 511.92 - 599.40 kg/hm2, K was 249.70 - 282.37 kg/hm2, and OF was 940.00 - 1 104.00 kg/hm2. N, P, K and OF obviously affect the yield of Ligusticum chuanxiong rhizome. K and OF can significantly increase the yield of Ligusticum chuanxiong rhizome. Thus it is suggested that properly high mount of K and OF and appropriate increasing N are two favorable factors for cultivating Ligusticum chuanxiong.

  17. Determination of borneol and other chemical compounds of ...

    African Journals Online (AJOL)

    Purpose: To determine borneol and other chemical compounds of essential oil derived from the exudate of Dryobalanops aromatica in Malaysia. Methods: Exudate was collected from D. aromatica and subjected to fractional distillation to obtain essential oil. Gas chromatography-mass spectrometry (GC-MS) was performed ...

  18. Raman Spectral Determination of Chemical Reaction Rate Characteristics

    Science.gov (United States)

    Balakhnina, I. A.; Brandt, N. N.; Mankova, A. A.; Chikishev, A. Yu.; Shpachenko, I. G.

    2017-09-01

    The feasibility of using Raman spectroscopy to determine chemical reaction rates and activation energies has been demonstrated for the saponification of ethyl acetate. The temperature dependence of the reaction rate was found in the range from 15 to 45°C.

  19. Computer program determines chemical composition of physical system at equilibrium

    Science.gov (United States)

    Kwong, S. S.

    1966-01-01

    FORTRAN 4 digital computer program calculates equilibrium composition of complex, multiphase chemical systems. This is a free energy minimization method with solution of the problem reduced to mathematical operations, without concern for the chemistry involved. Also certain thermodynamic properties are determined as byproducts of the main calculations.

  20. Systematic determination of the JET absolute neutron yield using the MPR spectrometer

    International Nuclear Information System (INIS)

    Kronborg-Pettersson, N.

    2003-04-01

    This thesis describes the first high-statistics systematic analysis of JET neutron yield and rate measurements obtained by using data acquired with the Magnetic Proton Recoil (MPR) neutron spectrometer. The neutron yield and rate were determined by using the count-rate from the MPR neutron spectrometer together with neutron profile information from other neutron diagnostic systems. This has previously been done manually for a few pulses. To be able to do this in a more systematic way a part of the neutron spectrum evaluation code was extracted and put into a separate custom-made program and modifications were done to extract sets of MPR data automatically. The codes have been used for analysis of a large set of pulses from the deuterium-tritium campaign at JET in 1997. Several results were obtained, the most significant of which was the clear improvement seen when neutron profile corrections were applied. Neutron yield-rates derived from MPR count-rate are shown to be in excellent agreement with other JET neutron diagnostic data

  1. Systematic determination of the JET absolute neutron yield using the MPR spectrometer

    Energy Technology Data Exchange (ETDEWEB)

    Kronborg-Pettersson, N

    2003-04-01

    This thesis describes the first high-statistics systematic analysis of JET neutron yield and rate measurements obtained by using data acquired with the Magnetic Proton Recoil (MPR) neutron spectrometer. The neutron yield and rate were determined by using the count-rate from the MPR neutron spectrometer together with neutron profile information from other neutron diagnostic systems. This has previously been done manually for a few pulses. To be able to do this in a more systematic way a part of the neutron spectrum evaluation code was extracted and put into a separate custom-made program and modifications were done to extract sets of MPR data automatically. The codes have been used for analysis of a large set of pulses from the deuterium-tritium campaign at JET in 1997. Several results were obtained, the most significant of which was the clear improvement seen when neutron profile corrections were applied. Neutron yield-rates derived from MPR count-rate are shown to be in excellent agreement with other JET neutron diagnostic data.

  2. Determination of the distribution of graft yields following a radiation-induced graft copolymerization

    International Nuclear Information System (INIS)

    Schipschack, K.; Wagner, H.; Sawtschenko, L.

    1976-01-01

    In the radiation-induced graft copolymerization on solid initial polymers a distribution of graft yields takes place along the cross-sections of samples. Methods for determining this distribution, which are described in the literature, are reviewed. In our own investigations boards made of ethylene-vinyl acetate copolymers and grafted with vinyl chloride were used. Distributions of the grafted component obtained by infrared analysis of microtome cuts parallel to the surface are partly rather inhomogeneous, and are interpreted as dependent on the experimental parameters. (author)

  3. Regression models of ultimate methane yields of fruits and vegetable solid wastes, sorghum and napiergrass on chemical composition

    Energy Technology Data Exchange (ETDEWEB)

    Gunaseelan, V.N. [PSG College of Arts and Science, Coimbatore (India). Department of Zoology

    2007-04-15

    Several fractions of fruits and vegetable solid wastes (FVSW), sorghum and napiergrass were analyzed for total solids (TS), volatile solids (VS), total organic carbon, total kjeldahl nitrogen, total soluble carbohydrate, extractable protein, acid-detergent fiber (ADF), lignin, cellulose and ash contents. Their ultimate methane yields (B{sub o}) were determined using the biochemical methane potential (BMP) assay. A series of simple and multiple regression models relating the B{sub o} to the various substrate constituents were generated and evaluated using computer statistical software, Statistical Package for Social Sciences (SPSS). The results of simple regression analyses revealed that, only weak relationship existed between the individual components such as carbohydrate, protein, ADF, lignin and cellulose versus B{sub o}. A regression of B{sub o} versus combination of two variables as a single independent variable such as carbohydrate/ADF and carbohydrate + protein/ADF also showed that the relationship is not strong. Thus it does not appear possible to relate the B{sub o} of FVSW, sorghum and napiergrass with single compositional characteristics. The results of multiple regression analyses showed promise and the relationship appeared to be good. When ADF and lignin/ADF were used as independent variables, the percentage of variation accounted for by the model is low for FVSW (r{sup 2}=0.665) and sorghum and napiergrass (r{sup 2}=0.746). Addition of nitrogen, ash and total soluble carbohydrate data to the model had a significantly higher effect on prediction of B{sub o} of these wastes with the r{sup 2} values ranging from 0.9 to 0.99. More than 90% of variation in B{sub o} of FVSW could be accounted for by the models when the variables carbohydrate, lignin, lignin/ADF, nitrogen and ash (r{sup 2}=0.904), carbohydrate, ADF, lignin/ADF, nitrogen and ash (r{sup 2}=0.90) and carbohydrate/ADF, lignin/ADF, lignin and ash (r{sup 2}=0.901) were used. All the models have

  4. Biochemical methane potential, biodegradability, alkali treatment and influence of chemical composition on methane yield of yard wastes.

    Science.gov (United States)

    Gunaseelan, Victor Nallathambi

    2016-03-01

    In this study, the biochemical CH4 potential, rate, biodegradability, NaOH treatment and the influence of chemical composition on CH4 yield of yard wastes generated from seven trees were examined. All the plant parts were sampled for their chemical composition and subjected to the biochemical CH4 potential assay. The component parts exhibited significant variation in biochemical CH4 potential, which was reflected in their ultimate CH4 yields that ranged from 109 to 382 ml g(-1) volatile solids added and their rate constants that ranged from 0.042 to 0.173 d(-1). The biodegradability of the yard wastes ranged from 0.26 to 0.86. Variation in the biochemical CH4 potential of the yard wastes could be attributed to variation in the chemical composition of the different fractions. In the Thespesia yellow withered leaf, Tamarindus fruit pericarp and Albizia pod husk, NaOH treatment enhanced the ultimate CH4 yields by 17%, 77% and 63%, respectively, and biodegradability by 15%, 77% and 61%, respectively, compared with the untreated samples. The effectiveness of NaOH treatment varied for different yard wastes, depending on the amounts of acid detergent fibre content. Gliricidia petals, Prosopis leaf, inflorescence and immature pod, Tamarindus seeds, Albizia seeds, Cassia seeds and Delonix seeds exhibited CH4 yields higher than 300 ml g(-1) volatile solids added. Multiple linear regression models for predicting the ultimate CH4 yield and biodegradability of yard wastes were designed from the results of this work. © The Author(s) 2016.

  5. Cura Annonae-Chemically Boosting Crop Yields Through Metabolic Feeding of a Plant Signaling Precursor.

    Science.gov (United States)

    Vocadlo, David J

    2017-05-22

    The cream of the crop: With the world facing a projected shortfall of crops by 2050, new approaches are needed to boost crop yields. Metabolic feeding of plants with photocaged trehalose-6-phosphate (Tre6P) can increase levels of the signaling metabolite Tre6P in the plant. Reprogramming of cellular metabolism by Tre6P stimulates a program of plant growth and enhanced crop yields, while boosting starch content. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. Phosphorescence quantum yield determination with time-gated fluorimeter and Tb(III)-acetylacetonate as luminescence reference

    Energy Technology Data Exchange (ETDEWEB)

    Penzkofer, A., E-mail: alfons.penzkofer@physik.uni-regensburg.de [Fakultät für Physik, Universität Regensburg, Universitätsstrasse 31, D-93053 Regensburg (Germany)

    2013-03-29

    Highlights: ► Procedure for absolute phosphorescence quantum yield measurement is described. ► Experimental setup for absolute luminescence quantum yield standard calibration. ► Tb(acac){sub 3} proposed as phosphorescence quantum yield reference standard. ► Luminescence quantum yield of Tb(acac){sub 3} in cyclohexane measured. ► Luminescence lifetime of Tb(acac){sub 3} in cyclohexane measured. - Abstract: Phosphorescence quantum yield measurements of fluorescent and phosphorescent samples require the use of time-gated fluorimeters in order to discriminate against the fluorescence contribution. As reference standard a non-fluorescent luminescent compound is needed for absolute phosphorescence quantum yield determination. For this purpose the luminescence behavior of the rare earth chelate terbium(III)-acetylacetonate (Tb(acac){sub 3}) was studied (determination of luminescence quantum yield and luminescence lifetime). The luminescence quantum yield of Tb(acac){sub 3} was determined by using an external light source and operating the fluorimeter in chemo/bioluminescence mode with a fluorescent dye (rhodamine 6G in methanol) as reference standard. A procedure is developed for absolute luminescence (phosphorescence) quantum yield determination of samples under investigation with a time-gated fluorimeter using a non-fluorescent luminescent compound of known luminescence quantum yield and luminescence lifetime.

  7. Method and analysis for determining yielding of titanium alloy with nonlinear Rayleigh surface waves

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Shifeng; Zhang, Lei; Mirshekarloo, Meysam Sharifzadeh; Chen, Shuting; Chen, Yi Fan; Wong, Zheng Zheng; Shen, Zhiyuan; Liu, Huajun; Yao, Kui, E-mail: k-yao@imre.a-star.edu.sg

    2016-07-04

    Methods for determining yielding of titanium (Ti) alloy material with second harmonic Rayleigh ultrasonic wave are investigated. Both piezoelectric angle beam transducers and high frequency laser scanning vibrometer (LSV) are used to detect ultrasonic signals in the Ti alloy specimens with different plastic strain levels. Technical features and outcomes with use of piezoelectric transducers and LSV are compared. The method using piezoelectric transducers, with much higher signal-to-noise ratio than LSV, has been further improved by deploying two transducers with central frequencies corresponding to the fundamental and second order harmonic signals respectively to improve the testing reliability and accuracy. Both the techniques using piezoelectric transducer and LSV demonstrate consistently that the acoustic nonlinearity increases with plastic strain, and the second harmonic Rayleigh ultrasonic wave can be utilized for effective determination of yielding in Ti alloy. Our experiments further show that the acoustic nonlinearity increases gradually with plastic strain at small plastic strain level, and there is a more significant increase of acoustic nonlinearity when the plastic strain reaches a higher level. Microscopic investigations using scanning electron microscopy (SEM) and high resolution transmission electron microscopy (HRTEM) are conducted for clarifying the relationship between the observed acoustic nonlinearity and micro-structural changes.

  8. Chemical methods for the determination of composition of cryolite

    International Nuclear Information System (INIS)

    Shivarudrappa, V.; Patil, B.N.; Marathe, S.G.; Jain, H.C.

    1989-01-01

    Preparation of uranium and plutonium alloys containing aluminium involves the use of cryolite and many times, cryolite which may be contaminated with alpha activity has to be analysed for its purity. In view of this, chemical methods for the determination of composition of commercial cryolite samples have been developed. Methods are standardised for the determination of individual constituents of cryolite viz., aluminium, sodium, fluoride and major impurities, calcium and magnesium. Studies on the dissolution of the sample, effect of one or more components on the determination of the other and their elimination are carried out. Aluminium and sodium are determined gravimetrically as oxinate and triple acetate respectively. Fluoride is determined by a volumetric procedure after cation exchange separtion of soluble fluoride. Calcium and magnesium are determined by a sequential pH-metri titration. This report describes the details of the procedures and the results of these studies for two commercial cryolite samples. (author). 7 tabs

  9. Foliar application effects of beet vinasse on rice yield and chemical composition

    International Nuclear Information System (INIS)

    Tejada, M.; Garcia-Martinez, A. M.; Benitez, C.; Gonzalez, J. L.; Bautista, J.; Parrado, J.

    2009-01-01

    This study presents an account of rice (oriza sativa cv. Puntal) yield quality parameters as influenced by the foliar application of an industrial byproduct (beet vinasse). Beet (Beta vulgaris L. Subsp.vurgaris) vinasse is a product of great agricultural interest, because of its organic matter content, N and K concentrations. (Author)

  10. Influence of density on radiation-chemical yield of molecular hydrogen formed at radiolysis of aqueous solution of NaOH

    International Nuclear Information System (INIS)

    Jafarov, Y.D.; Hajiyeva, S.R.; Ramazanova, N.K.; Aliyev, S.M.; Alasgarov, A.M.

    2014-01-01

    Full text : In atom and nuclear energy the specialists knowledge about radiation-chemical yield of the initial products formed under the influence of ionizing rays on water is of great importance from the point of security. The radiation-chemical yields of molecular hydrogen have been defined according to the graph and the obtained results

  11. Determinants of Operational Efficiency at Chemical Cargo Terminals

    Directory of Open Access Journals (Sweden)

    T.A. Gúlcan

    2014-06-01

    Full Text Available In today’s globalized world, one of the requirements of global supply chains is efficient transportation systems. Approximately 80 per cent of world merchandise trade carried by sea and handled by ports worldwide. For this reason, maritime transport has the strategic economic importance. Loading of oil and gas has the biggest share (%30 in commodities carried by sea and 2.9 billion tons oil and gas loaded to ship in 2013. This study is focus on chemical cargo terminals which is a special terminal form where high and international levels of safety and quality elements applied. Unlike conventional bulk cargo and container cargo operations, chemical cargo operations include own priorities, applications, and the evaluation criteria. The aim of this study is to perform a qualitative research to determine the factors affecting the operational efficiency of ship, berth and warehousing operations in chemical cargo terminals.

  12. Evaluation of pulsed streamer corona experiments to determine the O* radical yield

    International Nuclear Information System (INIS)

    Van Heesch, E J M; Winands, G J J; Pemen, A J M

    2008-01-01

    The production of O* radicals in air by a pulsed streamer plasma is studied by integration of a large set of precise experimental data and the chemical kinetics of ozone production. The measured data comprise ozone production, plasma energy, streamer volume, streamer length, streamer velocity, humidity and gas-flow rate. Instead of entering input parameters into a kinetic model to calculate the end products the opposite strategy is followed. Since the amount of end-products (ozone) is known from the measurements the model had to be applied in the reverse direction to determine the input parameters, i.e. the O* radical concentration.

  13. Evaluation of pulsed streamer corona experiments to determine the O* radical yield

    Science.gov (United States)

    van Heesch, E. J. M.; Winands, G. J. J.; Pemen, A. J. M.

    2008-12-01

    The production of O* radicals in air by a pulsed streamer plasma is studied by integration of a large set of precise experimental data and the chemical kinetics of ozone production. The measured data comprise ozone production, plasma energy, streamer volume, streamer length, streamer velocity, humidity and gas-flow rate. Instead of entering input parameters into a kinetic model to calculate the end products the opposite strategy is followed. Since the amount of end-products (ozone) is known from the measurements the model had to be applied in the reverse direction to determine the input parameters, i.e. the O* radical concentration.

  14. Evaluation the effects of organic, biological and chemical fertilizers on morphological traits, yield and yield components of Basil (Ocimum basilicum L.

    Directory of Open Access Journals (Sweden)

    S. M.K Tahhami Zarandi

    2015-04-01

    Full Text Available The use of organic manure and biofertilizers containing beneficial microorganisms instead of chemical fertilizers are known to improve plant growth through supply of plant nutrients and can help sustain environmental health and soil productivity. Because of special priority of the medicinal plants production in sustainable agricultural systems and lack of studies on assessment of different sources of fertilizer on basil plants, an experiment was conducted at Research Station, Faculty of Agriculture, Ferdowsi University of Mashhad, Iran, in 2009. A complete randomize block design with ten treatments, and three replications was used. The treatments were: 1cow manure, 2sheep manure, 3hen manure, 4compost 5vermicompost, 6biological fertilizer nitroxin (consisting of Azotobacter and Azospirillum, 7biological fertilizer consisting of Phosphate Solubilizing Bacteria (Pseudomonas and Bacillus, 8mixture of biological fertilizer nitroxin and Phosphate Solubilizing Bacteria 9NPK fertilizers, and 10control (no fertilizer. Results showed plant height in sheep manure was higher than other treatments. Number of branches in vermicompost and number of inflorescence in cow manure were significantly higher than other treatments. The number of whorled flowers in compost, sheep and cow manure were more than other treatments. Highest leaf and green area index was observed in nitroxin treatment and biological yield in sheep manure have significant difference with other treatments (except cow manure. The highest seed yield were obtained from plants treated with compost (1945 kg/h and the lowest of that observed in NPK fertilizer and control treatments. In all measured traits (except number of inflorescence NPK fertilizer and control treatment did not have any significant difference.

  15. Nucleic acid helix structure determination from NMR proton chemical shifts

    Energy Technology Data Exchange (ETDEWEB)

    Werf, Ramon M. van der; Tessari, Marco; Wijmenga, Sybren S., E-mail: S.Wijmenga@science.ru.nl [Radboud University Nijmegen, Department of Biophysical Chemistry, Institute of Molecules and Materials (Netherlands)

    2013-06-15

    We present a method for de novo derivation of the three-dimensional helix structure of nucleic acids using non-exchangeable proton chemical shifts as sole source of experimental restraints. The method is called chemical shift de novo structure derivation protocol employing singular value decomposition (CHEOPS) and uses iterative singular value decomposition to optimize the structure in helix parameter space. The correct performance of CHEOPS and its range of application are established via an extensive set of structure derivations using either simulated or experimental chemical shifts as input. The simulated input data are used to assess in a defined manner the effect of errors or limitations in the input data on the derived structures. We find that the RNA helix parameters can be determined with high accuracy. We finally demonstrate via three deposited RNA structures that experimental proton chemical shifts suffice to derive RNA helix structures with high precision and accuracy. CHEOPS provides, subject to further development, new directions for high-resolution NMR structure determination of nucleic acids.

  16. Determination of yield related traits of sesame genotypes selected from world collection and mutant material

    International Nuclear Information System (INIS)

    Silme, R. S.; Cagirgan, M. I.

    2009-01-01

    Sesame (Sesamum indicum L.) is an important plant of Turkey that secondary gen center and very used of food industry's a lot of area. Mutation breeding of sesame research continued coordinately with IAEA since 1993. it is aimed in these breeding programmes to improve lines that have dehiscent capsule, determinate growth and resistance to wilting traits. This study was conducted in Antalya City, at Akdeniz University Agricultural Faculty experiment fields under second crop conditions in 2007. At this study, 19 genotypes selected from world sesame collection, 4 mutant genotypes and 2 local cultivars were sown. The experiments were conducted according to Complete Randomized Block Design with three replications. It was found that first flowering date varied between 35 to 45 days, 50% flowering date from 39 to 54 days, last flowering date from 63 to 88 days, first capsule date from 42 to 51 days, first capsule height from 44 to 116 cm, plant height from 102 to 177 cm, number of branch per plant from 0.1 to 2.7, number of pod per plant from 28 to 63, number of seeds in capsule 2.3-4.3 g, 1000 seed weight ranged from 2.3 to 4.3 g, seed yield per da from 18 to 77 kg. The highest yield per da (77 kg/da) was obtained from mutant genotype, wt-5.

  17. Positronium Yields in Liquids Determined by Lifetime and Angular Correlation Measurements

    DEFF Research Database (Denmark)

    Mogensen, O. E.; Jacobsen, F. M.

    1982-01-01

    hydrocarbons), 3.2 (average value for 8 aromatic hydrocarbons), 2.6 (average value for 5 alcohols). Values of this ratio for various other liquids are also given. The results for the mixtures show how I'3 and I'1, vary as the Ps formation is inhibited (CCl4 mixtures) or enhanced C6F6 mixtures). The most......Positron lifetime and angular correlation spectra were measured for 36 pure liquids, CCl4 mixtures with hexane and diethylether, and C6F6 mixtures with hexane. Apparent ortho-Ps yields, I'3, were determined as the intensity of the long-lived component in the lifetime spectra, while the apparent...... para-Ps yields, I'3, were obtained as the intensity of the narrowest gaussian in a three-gaussian fit to the angular correlation spectra. The ratio I'3/I1, expected to be 3, was found to be instead 2.3 (average value for 3 ethers), 2.5 (average value for 10 linear, branched, and cyclic aliphatic...

  18. Effect of animal manure on quantitative and qualitative yield and chemical composition of essential oil in cumin (Cuminum cyminum

    Directory of Open Access Journals (Sweden)

    ahmad ahmadiyan

    2009-06-01

    Full Text Available Animal manure on soil prepares essential elements and increase water holding capacity and quality of plants. To study the effects of animal manure on yield and its components, nutrients absorption, chemical composition and its percentages on Cuminum cyminum this experiment was conducted at the agricultural researcher station of Zahak-Zabol, during 2003 – 2004 in a randomized complete block design with four replications. Animal manure significantly enhanced number of umbers per plant, number of seed per plant, biological and seed yield. Use of animal manure had not significant affect on Ca, Mg, Fe, P, K, Mn, Zn, and Cu and protein percentage in cumin seed but decreased Na concentration. Animal manure significantly enhanced cumin aldehyde and ρ-cymene and decrease β-pinene, γ-terpinene and α-pinene in cumin oil. A relationship or correlation exists between the main components of cumin oil. This study showed that animal manure enhances seed yield, oil percentage and qualitative chemical composition in cumin oil.

  19. Olive oil pilot-production assisted by pulsed electric field: impact on extraction yield, chemical parameters and sensory properties.

    Science.gov (United States)

    Puértolas, Eduardo; Martínez de Marañón, Iñigo

    2015-01-15

    The impact of the use of pulsed electric field (PEF) technology on Arroniz olive oil production in terms of extraction yield and chemical and sensory quality has been studied at pilot scale in an industrial oil mill. The application of a PEF treatment (2 kV/cm; 11.25 kJ/kg) to the olive paste significantly increased the extraction yield by 13.3%, with respect to a control. Furthermore, olive oil obtained by PEF showed total phenolic content, total phytosterols and total tocopherols significantly higher than control (11.5%, 9.9% and 15.0%, respectively). The use of PEF had no negative effects on general chemical and sensory characteristics of the olive oil, maintaining the highest quality according to EU legal standards (EVOO; extra virgin olive oil). Therefore, PEF could be an appropriate technology to improve olive oil yield and produce EVOO enriched in human-health-related compounds, such as polyphenols, phytosterols and tocopherols. Copyright © 2014 Elsevier Ltd. All rights reserved.

  20. Determination of the shape factor of 90Sr by means of the cutoff energy yield method

    International Nuclear Information System (INIS)

    Grau Carles, A.; Kossert, K.; Grau Malonda, A.

    2008-01-01

    Usually, Kurie plots are used to analyze beta-spectra shape-factor functions measured by means of semiconductor and magnetic spectrometers. A drawback of these techniques is the occurrence of self-absorption within the samples through which the emission spectrum is altered. In liquid-scintillation samples self-absorption does not occur, but the poor energy resolution makes the analysis of the spectra difficult. To overcome this problem, two resolution-invariant observables are used for determining the shape-factor function of 90 Sr: (1) the maximum point energy and (2) the cutoff energy yield. The measured shape-factor function of 90 Sr agrees with the one which is predicted by theory for the first-forbidden unique transition

  1. Automatic chemical determination facility for plutonium and uranium

    International Nuclear Information System (INIS)

    Benhamou, A.

    1980-01-01

    A proposal for a fully automated chemical determination system for uranium and plutonium in (U, Pu)O 2 mixed oxide fuel, from the solid sample weighing operation to the final result is described. The steps completed to data are described. These include: test sample preparation by weighing, potentiometer titration system, cleaning and drying of glassware after titration. The process uses a Mettler SR 10 Titrator System in conjunction with others automatized equipment in corse of realization. Precision may reach 0.02% and is generally better than 0.1%. Accuracy in within +-0.1% of manual determination results or titration standards [fr

  2. Harnessing the respiration machinery for high-yield production of chemicals in metabolically engineered Lactococcus lactis

    DEFF Research Database (Denmark)

    Liu, Jianming; Wang, Zhihao; Kandasamy, Vijayalakshmi

    2017-01-01

    on metabolically engineered Lactococcus lactis strains to optimize the production of acetoin and (R,R)−2,3-butanediol (R-BDO). In the absence of an external electron acceptor, a surplus of two NADH per acetoin molecule is produced. We found that a fully activated respiration was able to efficiently regenerate NAD......+, and a high titer of 371 mM (32 g/L) of acetoin was obtained with a yield of 82% of the theoretical maximum. Subsequently, we extended the metabolic pathway from acetoin to R-BDO by introducing the butanediol dehydrogenase gene from Bacillus subtilis. Since one mole of NADH is consumed when acetoin...... is converted into R-BDO per mole, only the excess of NADH needs to be oxidized via respiration. Either by fine-tuning the respiration capacity or by using a dual-phase fermentation approach involving a switch from fully respiratory to non-respiratory conditions, we obtained 361 mM (32 g/L) R-BDO with a yield...

  3. Comparing milk yield, chemical properties and somatic cell count from organic and conventional mountain farming systems

    Directory of Open Access Journals (Sweden)

    Marcello Bianchi

    2010-01-01

    Full Text Available A study was undertaken to investigate the effects of farming systems (organic vs. conventional, diet (hay/concentrate vs. pasture and their interaction on milk yield, gross composition and fatty acid (FA profile of dairy cows bred in mountainous areas. For this purpose four dairy farms (two organic and two conventional were chosen in the alpine territory of Aosta Valley (NW Italy; individual milk yield was recorded daily and bulk milk samples were collected monthly from February to September 2007 to cover dietary variations. Higher levels of milk production (P<0.05 and lower milk protein amounts (P<0.01 were observed in the organic farms with respect to the conventional ones, while no significant differences were noticed in milk fat and lactose contents and in somatic cell count. Concerning fatty acids, only small differences were detected between organic and conventional milk and such differences seemed to be related mainly to the stabled period. Diet affected almost all variables studied: pasture feeding provided a significant improvement in the fatty acid composition in both organic and conventional systems leading to lower hypercholesterolemic saturated fatty acids, higher mono- and polyunsaturated fatty acids and conjugated linoleic acid amounts (P<0.001.

  4. Enhanced Soil Chemical Properties and Rice Yield in Acid Sulphate Soil by Application of Rice Straw

    Directory of Open Access Journals (Sweden)

    Siti Nurzakiah

    2012-01-01

    Full Text Available Swampland development such as acid sulphate soil for agricultural cultivation has various problem, including highsoil acidity, fluctuated and unpredictable water flooding and the presence of toxic elements such as Fe whichresulting in low crop yields. The research was conducted at the experimental station Belandean, Barito Kualaregency in dry season 2007. The objective of research was to study the effect of rice straw on the dynamic of soilpH, the concentration of iron and sulphate and yield on tidal land acid sulphate soil at two different water inletchannel. This research was designed in RCBD (Randomized Completely Block Design with five treatments (0, 2.5,5.0, 7.5 and 10 Mg ha-1 and four replications. Dolomite as much as 1 Mg ha-1 was also applied. This research wasdivided into two sub-units experiment i.e. two conditions of different water inlet channel. The first water channelswere placed with limestone and the second inlet was planted with Eleocharis dulcis. The results showed that (i ricestraw application did not affect the dynamic of soil pH, concentration of iron and sulphate, and (ii the highest yieldwas obtained with 7.5 Mg ha-1 of rice straw.

  5. Quantum dots assisted photocatalysis for the chemiluminometric determination of chemical oxygen demand using a single interface flow system

    Energy Technology Data Exchange (ETDEWEB)

    Silvestre, Cristina I.C.; Frigerio, Christian [Requimte, Department of Chemistry, Faculty of Pharmacy, Porto University, Rua Anibal Cunha 164, 4099-030, Porto (Portugal); Santos, Joao L.M., E-mail: joaolms@ff.up.pt [Requimte, Department of Chemistry, Faculty of Pharmacy, Porto University, Rua Anibal Cunha 164, 4099-030, Porto (Portugal); Lima, Jose L.F.C. [Requimte, Department of Chemistry, Faculty of Pharmacy, Porto University, Rua Anibal Cunha 164, 4099-030, Porto (Portugal)

    2011-08-12

    Highlights: {yields} A novel flow method for the determination of chemical oxygen demand is proposed. {yields} CdTe nanocrystals are irradiated with UV light to generate strong oxidizing species. {yields} Reactive species promote a fast catalytic degradation of organic matter. {yields} Luminol is used as a chemiluminescence probe for indirect COD assessment. {yields} A single interface flow system was implemented to automate the assays. - Abstract: A novel flow method for the determination of chemical oxygen demand (COD) is proposed in this work. It relies on the combination of a fully automated single interface flow system, an on-line UV photocatalytic unit and quantum dot (QD) nanotechnology. The developed approach takes advantage of CdTe nanocrystals capacity to generate strong oxidizing species upon irradiation with UV light, which fostered a fast catalytic degradation of the organic compounds. Luminol was used as a chemiluminescence (CL) probe for indirect COD assessment, since it is easily oxidized by the QD generated species yielding a strong CL emission that is quenched in the presence of the organic matter. The proposed methodology allowed the determination of COD concentrations between 1 and 35 mg L{sup -1}, with good precision (R.S.D. < 1.1%, n = 3) and a sampling frequency of about 33 h{sup -1}. The procedure was applied to the determination of COD in wastewater certified reference materials and the obtained results showed an excellent agreement with the certified values.

  6. chemical determination of burnup ratio in nuclear fuels

    International Nuclear Information System (INIS)

    Guereli, L.

    1997-01-01

    Measurements of the extent of fission are important to determine the irradiation performance of a nuclear fuel. The energy released per unit mass of uranium (burnup) can be determined from measurement of the percent of heavy atoms that have fissioned during irradiation.The preferred method for this determination is choosing a suitable fission monitor (usually ''1''4''8Nd) and its determination after separation from the fuel matrix. In thermal reactor fuels where the only heavy element in the starting material is uranium, uranium depletion can be used for burnup determination. ''2''3''5U depletion method requires measurement of uranium isotopic ratios of both irradiated and unirradiated fuel. Isotopic ratios can be determined by thermal ionization mass spectrometer following separation of uranium from the fuel matrix. Separation procedures include solvent extraction, ion exchange and anion exchange chromatography. Another fission monitor used is ''1''3''9La determination by HPLC. Because La is monoisotopic (''1''3''9La) in the fuel, it can be determined by chemical analysis techniques

  7. Chemical and Mechanical Weed Control Methods and Their Effects on Photosynthetic Pigments and Grain Yield of Kidney Bean

    Directory of Open Access Journals (Sweden)

    A.S Ghatari

    2015-11-01

    Full Text Available To evaluate the integrated management of weeds in red kidney bean, a split-plot experiment using randomized complete block design with three replications was conducted in 2013 in the Damavand County. In this experiment, the mechanical control treatments consisted of two levels (no cultivation and one cultivation asseigned to main plots and controlling chemical treatments consisted of six levels (non-application of herbicides, pre-emergence herbicide application of Pursuit with full dose of 1 liter per hectare, pre-emergence herbicide application of Pursuit a dose decreased 0.5 liters per hectare, post-emergence herbicide application of Pursuit dose reduced to 0.3 liters per hectare + 2 thousand citogate, post-emergence herbicide application of Pursuit with a reduced dose of 0.5 liters per hectare + 2 thousand citogate, post-emergence herbicide application of Pursuit full dose of 1 liter per hectar + 2 thousand citogate to subplots. The results showed that the effects of interaction between herbicide application and cultivation for traits of carotenoids, chlorophyll a, chlorophyll b and total chlorophyll contents, density of weeds and their dry weights were significant at 1 %, and grain yield at the 5% probability levels. The highest bean seed yield with an average of 5461.6 kg.ha-1 and lowest weed dry weight with an average of 345.9 kg.ha-1 were related to pre-emergence herbicide and cultivation with a dose of 1 liter per hectare treatment. The difference between full and reduced doses of chemical weed control was non-significant. It could be concluded that integrated mechanical and chemical weed control not only may increase seed yield but also reduce, environmental hazards.

  8. Sputtering yields and surface chemical modification of tin-doped indium oxide in hydrocarbon-based plasma etching

    Energy Technology Data Exchange (ETDEWEB)

    Li, Hu; Karahashi, Kazuhiro; Hamaguchi, Satoshi, E-mail: hamaguch@ppl.eng.osaka-u.ac.jp [Center for Atomic and Molecular Technologies, Osaka University, Yamadaoka 2-1, Suita 565-0871 (Japan); Fukasawa, Masanaga; Nagahata, Kazunori; Tatsumi, Tetsuya [Device and Material R& D Group, RDS Platform, Sony Corporation, Kanagawa 243-0014 (Japan)

    2015-11-15

    Sputtering yields and surface chemical compositions of tin-doped indium oxide (or indium tin oxide, ITO) by CH{sup +}, CH{sub 3}{sup +}, and inert-gas ion (He{sup +}, Ne{sup +}, and Ar{sup +}) incidence have been obtained experimentally with the use of a mass-selected ion beam system and in-situ x-ray photoelectron spectroscopy. It has been found that etching of ITO is chemically enhanced by energetic incidence of hydrocarbon (CH{sub x}{sup +}) ions. At high incident energy incidence, it appears that carbon of incident ions predominantly reduce indium (In) of ITO and the ITO sputtering yields by CH{sup +} and CH{sub 3}{sup +} ions are found to be essentially equal. At lower incident energy (less than 500 eV or so), however, a hydrogen effect on ITO reduction is more pronounced and the ITO surface is more reduced by CH{sub 3}{sup +} ions than CH{sup +} ions. Although the surface is covered more with metallic In by low-energy incident CH{sub 3}{sup +} ions than CH{sup +} ions and metallic In is in general less resistant against physical sputtering than its oxide, the ITO sputtering yield by incident CH{sub 3}{sup +} ions is found to be lower than that by incident CH{sup +} ions in this energy range. A postulation to account for the relation between the observed sputtering yield and reduction of the ITO surface is also presented. The results presented here offer a better understanding of elementary surface reactions observed in reactive ion etching processes of ITO by hydrocarbon plasmas.

  9. Yield of 73Se for various reactions and its chemical processing

    International Nuclear Information System (INIS)

    Nozaki, T.; Itoh, Y.; Ogawa, K.

    1979-01-01

    Excitation curves for the formation of 73 Se by the following reactions were measured up to proton energy of 50 MeV and 3 He- and α-particle energies of 40 MeV, together with those for byproduct formation reactions: (1) 75 As(p, 3n) 73 Se, (2) Ge + 3 He → 73 Se, and (3) Ge + α → 73 Se. The proton reaction has proved to be much superior to the other reactions both in yield and product purity. Volatilization of 73 Se from a solution of condensed polyphosphoric acid was found to give an excellent method of 73 Se separation from various arsenic targets without carrier. Also, solvent extraction of red selenium 73 Se with a minute amount of carrier was shown to be a useful separation method. (author)

  10. Effect of Biological and Chemical Fertilizers on Oil, Seed Yield and some Agronomic Traits of Safflower under Different Irrigation Regimes

    Directory of Open Access Journals (Sweden)

    Hamidreza Fanaei

    2017-08-01

    Full Text Available Introduction Safflower Carthamus tinctorius L. is a tolerant plant to water deficit due to long roots and capability for high water absorption from soil deeper parts. Safflower can growth successfully in regions with low soil fertility and temperature. Behdani and Mosavifar (2011 reported that drought stress affect on yield by reducing yield components and agronomic traits. Biofertilizer during a biological process chanced the nutrients from unusable to usable form for plants in soils (Aseretal, 2008. Mirzakhani et al. (2008 found that inoculation of seed with free-living bacterium azotobacter and a symbiotic fungus productive mycorrhiza addition to increasing oil and seed cause increasing resistance against two factors of unfavorable environmental and to improve quality of product. In order to study the effect of biological and chemical fertilizers on oil, seed yield and some of agronomic traits of Safflower under irrigation of different regimes an experimental design was conducted. Materials and methods In order to study the effect of biological and chemical fertilizers on oil, seed yield and some of agronomic traits of safflower under irrigation of different regimes an experiment was carried out split plot based on randomized complete block design (RCBD with three replications in experimental farm of payame-Noor university of Zabol during 2012-2013 growing season. Irrigation regime in three levels include: I1 (control irrigation in all growth stages, I2 stop irrigation from sowing to flowering (irrigation in growth stages flowering, and seed filling, I3 irrigation in growth stages rosset, stem elongation, heading and stop irrigation in flowering, and seed filling were as main plots and fertilizer resources in five levels included: F1 non application chemical fertilizer (control, F2 pure application chemical fertilizer (NPK 99, 44 and 123 kg.ha-1 respectively, F3 Nitroxin application (2 L.ha-1 F4 Azotobacter application (2 L.ha-1 and F5

  11. Determination of mercury in ppb level by activation analysis and chemical separation

    International Nuclear Information System (INIS)

    Requejo, C.S.

    1983-02-01

    A method for determining mercury in steel samples was developed. Activation analysis using thermal neutrons, followed by radiochemical separations to eliminate 75 Se interferences, were applied. Sixty hours after the end of the irradiation, the samples were processed and distillation of mercury and selenium bromides were carried out. Selenium was separated as an element and mercury sulfide was precipitaded. The chemical separation procedure was tested by using a tracer technique; the recovery yield was 99,2% + - 2,7%. (C.L.B.) [pt

  12. How to tackle chemical communication? Relative proportions versus semiquantitative determination of compounds in lizard chemical secretions.

    Science.gov (United States)

    García-Roa, Roberto; Sáiz, Jorge; Gómara, Belén; López, Pilar; Martín, José

    2018-02-01

    Knowledge about chemical communication in some vertebrates is still relatively limited. Squamates are a glaring example of this, even when recent evidences indicate that scents are involved in social and sexual interactions. In lizards, where our understanding of chemical communication has considerably progressed in the last few years, many questions about chemical interactions remain unanswered. A potential reason for this is the inherent complexity and technical limitations that some methodologies embody when analyzing the compounds used to convey information. We provide here a straightforward procedure to analyze lizard chemical secretions based on gas chromatography coupled to mass spectrometry that uses an internal standard for the semiquantification of compounds. We compare the results of this method with those obtained by the traditional procedure of calculating relative proportions of compounds. For such purpose, we designed two experiments to investigate if these procedures allowed revealing changes in chemical secretions 1) when lizards received previously a vitamin dietary supplementation or 2) when the chemical secretions were exposed to high temperatures. Our results show that the procedure based on relative proportions is useful to describe the overall chemical profile, or changes in it, at population or species levels. On the other hand, the use of the procedure based on semiquantitative determination can be applied when the target of study is the variation in one or more particular compounds of the sample, as it has proved more accurate detecting quantitative variations in the secretions. This method would reveal new aspects produced by, for example, the effects of different physiological and climatic factors that the traditional method does not show.

  13. Determination of uranium and thorium during chemical treatment of monazite

    International Nuclear Information System (INIS)

    El-Nadi, Y.A.; Daoud, J.A.; Aly, H.F.; Kregsamer, P.

    2000-01-01

    Total reflection x-ray fluorescence (TXRF) is a very useful technique for both qualitative and quantitative analysis because of its high detection power and its needed to small sample volumes (less than 100 μl are sufficient). In this work TXRF was used to determine the initial concentrations of the elements included in monazite sand and following up the chemical steps for treatment of monazite with special attention to uranium and thorium concentration as well as lanthanides. The results were compared to those obtained from EDXRF and ICP-MS techniques. (author)

  14. Chemical magnetization when determining Thellier paleointensity experiments in oceanic basalts

    Science.gov (United States)

    Tselebrovskiy, Alexey; Maksimochkin, Valery

    2017-04-01

    The natural remanent magnetization (NRM) of oceanic basalts selected in the rift zones of the Mid-Atlantic Ridge (MAR) and the Red Sea has been explored. Laboratory simulation shows that the thermoremanent magnetization and chemical remanent magnetization (CRM) in oceanic basalts may be separated by using Tellier-Coe experiment. It was found that the rate of CRM destruction is about four times lower than the rate of the partial thermoremanent magnetization formation in Thellier cycles. The blocking temperatures spectrum of chemical component shifted toward higher temperatures in comparison with the spectrum of primary thermoremanent magnetization. It was revealed that the contribution of the chemical components in the NRM increases with the age of oceanic basalts determined with the analysis of the anomalous geomagnetic field (AGF) and spreading theory. CRM is less than 10% at the basalts aged 0.2 million years, less than 50% at basalts aged 0.35 million years, from 60 to 80% at basalts aged 1 million years [1]. Geomagnetic field paleointensity (Hpl) has been determined through the remanent magnetization of basalt samples of different ages related to Brunhes, Matuyama and Gauss periods of the geomagnetic field polarity. The value of the Hpl determined by basalts of the southern segment of MAR is ranged from 17.5 to 42.5 A/m, by the Reykjanes Ridge basalts — from 20.3 to 44 A/m, by the Bouvet Ridge basalts — from 21.7 to 34.1 A/m. VADM values calculated from these data are in good agreement with the international paleointensity database [2] and PISO-1500 model [3]. Literature 1. Maksimochkin V., Tselebrovskiy A., (2015) The influence of the chemical magnetization of oceanic basalts on determining the geomagnetic field paleointensity by the thellier method, moscow university physics bulletin, 70(6):566-576, 2. Perrin, M., E. Schnepp, and V. Shcherbakov (1998), Update of the paleointensity database, Eos Trans. AGU, 79, 198. 3. Channell JET, Xuan C, Hodell DA (2009

  15. Determination of air pollutants by nuclear chemical analysis

    International Nuclear Information System (INIS)

    Lesny, J.; Toelgyessy, J.

    1975-01-01

    Nuclear analytical methods are discussed with a view to their applicability in the determination of air pollutants. It is shown that some methods (use of radioactive kryptonates in automatic analyzers, application of activation analysis, X-ray fluorescence methods) are developed in theory and proven in practice in such an extent to be widely used in the near future in the control of the environment. Many other methods are becoming increasingly important for the solution of specific problems of environmental protection (such as the control of sudden environmental contamination in the proximity of chemical plants and industrial centers). (author)

  16. Chemical evolution with rotating massive star yields - I. The solar neighbourhood and the s-process elements

    Science.gov (United States)

    Prantzos, N.; Abia, C.; Limongi, M.; Chieffi, A.; Cristallo, S.

    2018-05-01

    We present a comprehensive study of the abundance evolution of the elements from H to U in the Milky Way halo and local disc. We use a consistent chemical evolution model, metallicity-dependent isotopic yields from low and intermediate mass stars and yields from massive stars which include, for the first time, the combined effect of metallicity, mass loss, and rotation for a large grid of stellar masses and for all stages of stellar evolution. The yields of massive stars are weighted by a metallicity-dependent function of the rotational velocities, constrained by observations as to obtain a primary-like 14N behaviour at low metallicity and to avoid overproduction of s-elements at intermediate metallicities. We show that the Solar system isotopic composition can be reproduced to better than a factor of 2 for isotopes up to the Fe-peak, and at the 10 per cent level for most pure s-isotopes, both light ones (resulting from the weak s-process in rotating massive stars) and the heavy ones (resulting from the main s-process in low and intermediate mass stars). We conclude that the light element primary process (LEPP), invoked to explain the apparent abundance deficiency of the s-elements with A values of ^{12}C/^{13}C in halo red giants, which is rather due to internal processes in those stars.

  17. Effect of Pseudomonas and Bacillus bacteria on Yield and Nutrient Uptake in Comparison with Chemical and Organic Fertilizers in Wheat

    Directory of Open Access Journals (Sweden)

    A. Fallah Nosrat Abad

    2015-06-01

    Full Text Available The high cost of fertilizers in farming systems, soil pollution and degradation of soil are factors that caused to full use of available renewable nutrient sources of plant (organic and biological with optimal application of fertilizers in order to maintain fertility, structure, biological activity, exchange capacity and water-holding capacity of the water in soil. Therefore, in recent years, according to investigators biofertilizers and organic farming as an alternative to chemical fertilizers has been drawn. Through this study, we examined the effects of triple superphosphate, organic matters and phosphate solubilizing microorganisms on quantitative and qualitative yield of wheat and nutrient uptake. The experiment was carried out in the factorial based on randomized complete block design. The factors were: 1-phosphate solubilizing bacteria in three levels including control, Pseudomonas Putida and Bacillus Coagulans bacteria, 2- triple superphosphate in five levels of 0, 25%, 50%, 75% and 100% and 3-organic matter in 2 levels of 0 and 15 ton/ha in the soil with high phosphorous accessibility (13 mg/kg soil but lower than sufficient limit for plant 15 mg/kg soil. The results showed that the highest amount of yield has been recorded in Pseudomonas Putida bacteria treatment with organic matter and 25% phosphate fertilizer. As a result, at the conditions of this experiment phosphate solubilizing bacteria and organic matter significantly had higher yield than control and their combination with phosphate fertilizer had significant effect on reducing phosphate fertilizer use.

  18. Effect of Treated Wastewater Combined with Various Amounts of Manure and Chemical Fertilizers on Nutrient Content and Yield in Corn

    Directory of Open Access Journals (Sweden)

    Abolfazal Tavassoli

    2010-09-01

    Full Text Available In order to study the effects of treated wastewater combined with manure and chemical fertilizers on the nutrients content and forage yield in corn, field experiments were conducted in 2007. The experiments were conducted in a split plot design with three replications. The treatments were comprised of two levels of irrigation water (W1= well water and W2= wastewater in the main plot and five levels of fertilizer (F1= unfertilized, F2 = 100% manure, F3= 50% manure, F4= 100% fertilizer, and F5= 50% fertilizer in the subplot. Results showed that, compared to ordinary water, irrigation with treated wastewater significantly increased fresh and dry forage yield of corn. The treatment using treated wastewater also had a significant effect on N, P, and K contents in corn forage. However, wastewater had no significant effect on plant Fe, Mn, and Zn contents. Among the fertilizer treatments, the highest fresh and dry forage yields and the highest N, P and K contents belonged to the treatments using 100% fertilizer. The highest Fe, Mn, and Zn contents were observed in plants in the treatment with 100% manure.

  19. High Yield Chemical Vapor Deposition Growth of High Quality Large-Area AB Stacked Bilayer Graphene

    Science.gov (United States)

    Liu, Lixin; Zhou, Hailong; Cheng, Rui; Yu, Woo Jong; Liu, Yuan; Chen, Yu; Shaw, Jonathan; Zhong, Xing; Huang, Yu; Duan, Xiangfeng

    2012-01-01

    Bernal stacked (AB stacked) bilayer graphene is of significant interest for functional electronic and photonic devices due to the feasibility to continuously tune its band gap with a vertical electrical field. Mechanical exfoliation can be used to produce AB stacked bilayer graphene flakes but typically with the sizes limited to a few micrometers. Chemical vapor deposition (CVD) has been recently explored for the synthesis of bilayer graphene but usually with limited coverage and a mixture of AB and randomly stacked structures. Herein we report a rational approach to produce large-area high quality AB stacked bilayer graphene. We show that the self-limiting effect of graphene growth on Cu foil can be broken by using a high H2/CH4 ratio in a low pressure CVD process to enable the continued growth of bilayer graphene. A high temperature and low pressure nucleation step is found to be critical for the formation of bilayer graphene nuclei with high AB stacking ratio. A rational design of a two-step CVD process is developed for the growth of bilayer graphene with high AB stacking ratio (up to 90 %) and high coverage (up to 99 %). The electrical transport studies demonstrated that devices made of the as-grown bilayer graphene exhibit typical characteristics of AB stacked bilayer graphene with the highest carrier mobility exceeding 4,000 cm2/V·s at room temperature, comparable to that of the exfoliated bilayer graphene. PMID:22906199

  20. Determination of Dacarbazine Φ-Order Photokinetics, Quantum Yields, and Potential for Actinometry.

    Science.gov (United States)

    Maafi, Mounir; Lee, Lok-Yan

    2015-10-01

    The characterization of drugs' photodegradation kinetics is more accurately achieved by means of the recently developed Φ-order kinetics than by the zero-, first-, and/or second-order classical treatments. The photodegradation of anti-cancer dacarbazine (DBZ) in ethanol has been investigated and found to obey Φ-order kinetics when subjected to continuous and monochromatic irradiation of various wavelengths. Its photochemical efficiency was proven to be wavelength dependent in the 220-350 nm range, undergoing a 50-fold increase. Albeit this variation was well defined by a sigmoid pattern, the overall photoreactivity of DBZ was proven to depend also on the contributions of reactants and experimental attributes. The usefulness of DBZ to serve as a drug-actinometer has been investigated using the mathematical framework of Φ-order kinetics. It has been shown that DBZ in ethanol can represent a good candidate for reliable actinometry in the range 270-350 nm. A detailed and easy-to-implement procedure has been proposed for DBZ actinometry. This procedure could advantageously be implemented prior to the determination of the photodegradation quantum yields. This approach might be found useful for the development of many drug actinometers as alternatives to quinine hydrochloride. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

  1. Effect of Vermicompost, Sulfur and Thiobacillus on Some Soil Physico-chemical Properties, Yield and Yield Components of Maize (Zea mays L. in Jovain District

    Directory of Open Access Journals (Sweden)

    Mahmmud Ahmadi

    2018-02-01

    Full Text Available Introduction The excessive use of chemical fertilizers causes environmental pollution that is led to imbalance of essential elements in agricultural production system. Organic matter application as compost in the soil can improve chemical quality and biochemical properties that increase essential elements for plant nutrition. Application of organic manure can significantly increase the soil aggregate as well. Reported that application of 7 ton ha-1 of vermicompost increased number of leaves, stem dry weight, and corn plant height as compared to control and water holding capacity increases. Sulphur in plant is near to phosphorus (0.2%. Sulphur deficiency cause severe reduction in plant growth and due to participation in protein building and its deficiency cause yellowish in younger leaves. Sulphur can be applied as elemental sulphur, with ammonium and super phosphate to the soil. Iran is situated in arid and semi arid region of the world and need to reduce the pH with sulphur application due to high pH above 8 in some parts. The aim of this research was to study the effect of above factors in yield and yield components of maize and reducing environmental pollution. Materials and Methods This research carried out at 2012 in Jovein Distract suberb of Sabzevar city. Before conducting the research soil sample were collected from 0-30 cm depth and physical and chemical properties of the soil were estimated. Treatments including sulphur, thiobacillus and vermicompost were applied to soil and well mixed with soil before sowing. Each plot consists of five rows with six m length by 80 cm from each other. Seeds were sown at the depth of five cm and 20 cm from each other. This research carried out as a factorial experiment on the basis of randomized complete block design. In this research three factors including elemental sulphur, vermicompost and thiobacillus were used with three replications. Elemental sulphur in three levels (control, 500 kg ha-1 and

  2. Effect of Bio-fertilizers in Combination with Different Rates of Chemical Fertilizers on the Growth Characters and Sepals Yield of Roselle (Hibiscus sabdariffa L.

    Directory of Open Access Journals (Sweden)

    roghayeh mohammadpour vashvaei

    2017-10-01

    Full Text Available Roselle or Maki tea (Hibiscus sabdariffa L. is a subtropical medicinal and aromatic plant belongs to the family Malvaceae that sepals of it's due to its medicinal properties and culinary uses. To evaluate the effect of bio-fertilizers in combination with different rates of chemical fertilizers on the growth characters, sepals yield and yield components of roselle, an experiment was conducted in randomized coplete block design with three replications, at the Research Station in Zabol University, during 2012 and 2013. Experimental treatments were plant nutrition with NPK, biophosphate, biophosphate+25% NPK, biophosphate+50% NPK, biophosphate+ 100% NPK, nitroxin, nitroxin+25%NPK, nitroxin+50%NPK, nitroxin+100%NPK, nitroxin+biophosphate, nitroxin+ biophosphate+25% NPK, nitroxin+biophosphate+50% NPK, nitroxin+biophosphate+100% NPK and control (non-use of any fertilizer. Plant traits such as plant height, no. of branches.plant-1, fresh and dry weight of vegetative, roots fresh and dry weight, calyx no.plant-1, sepal dry weight, sepals yield of roselle were measured. The results of combined analysis of variance showed that the effect of fertilizer were significant (P≤0.01 for all studied traits. Calyx no.plant-1 was the most important component in determining the sepals yield. The highest of all studied triates belong to nitroxin+biophosphate+100% NPK treatment that its difference with nitroxin+ biophosphate+50% NPK treatment was not significant. Thus, with respect to the production of medicinal plants in cropping systems and attention to the cultivation of these plants in low input systems, to improve plant growth and increase the sepals yield of roselle, 50% of the recommended dose of fertilizers with bio-fertilizers is recommended.

  3. Modeling precipitation-runoff relationships to determine water yield from a ponderosa pine forest watershed

    Science.gov (United States)

    Assefa S. Desta

    2006-01-01

    A stochastic precipitation-runoff modeling is used to estimate a cold and warm-seasons water yield from a ponderosa pine forested watershed in the north-central Arizona. The model consists of two parts namely, simulation of the temporal and spatial distribution of precipitation using a stochastic, event-based approach and estimation of water yield from the watershed...

  4. Evaluation Of Yield And Chemical Properties Of Some Faba Bean (Vicia FABA L.) Mutants Induced By GAMMA Radiation And Ethyl Methane Sulphonate

    International Nuclear Information System (INIS)

    Sallam, E.M.; Nasr, E.H.; Attia, Z.M.; Shawki, H.A.

    2013-01-01

    This investigation aims to study the effect of physical and chemical mutagens on the yield and chemical properties as well as amino acids composition of defatted faba bean (Vicia faba L.) seeds meal as a control (Giza 2) compared with mutants produced by gamma radiation and ethyl methane sulphonate (EMS). Also, the functional properties of these samples were determined. The results indicated high differences between mutation for seed yield and its components than the untreated samples. In addition, radiation mutation of faba bean seeds showed slight increase in protein content as the main constituent of faba bean seeds as well as total oil percentages in some mutant of these seeds in return of decreasing in total carbohydrate. Furthermore, radiation mutation had detectable effects on the total amino acids contents of faba bean seeds meal which had a higher percentages on essential amino acids (EAA) and non-essential amino acids (NEAA) and mutant 3 was the highest values of EAA and NEAA as compared to the control. On the other hand, radiation mutation improved the protein functional properties of some mutant of faba bean meal flour than the other mutant samples as compared to local commercial variety

  5. Determinants of the Government Bond Yield in Spain: A Loanable Funds Model

    Directory of Open Access Journals (Sweden)

    Yu Hsing

    2015-07-01

    Full Text Available This paper applies demand and supply analysis to examine the government bond yield in Spain. The sample ranges from 1999.Q1 to 2014.Q2. The EGARCH model is employed in empirical work. The Spanish government bond yield is positively associated with the government debt/GDP ratio, the short-term Treasury bill rate, the expected inflation rate, the U.S. 10 year government bond yield and a dummy variable representing the debt crisis and negatively affected by the GDP growth rate and the expected nominal effective exchange rate.

  6. Nitrogen and water regime effects on corn yields determined by N-15 methodology

    International Nuclear Information System (INIS)

    Halitligil, M.B.; Akin, A.

    2002-01-01

    This investigation was carried out to determine the relationships between fertilizer N leaching and N fertilizer application time, method and irrigation rate by using 15 N methodology. Therefore, in the field experiments, the effects of three factors namely a) Irrigation rate (optimum 240 mm, high 360 mm), b) N application time (All at planting, 1/2 at planting and 1/2 after planting when plant heights were 50 cm), c) N application method (side dress and broadcast) were investigated. The field experiments were conducted using randomized block design as split-split plot and 4 replications. As the test plant hybrid corn was selected and at planting row spaces were arranged as 0.80 m x 0.25 m. Nitrogen was applied 120 kg N/ha to the all treatments as urea fertilizer (46 % N). In addition, to the sub-plots (which received half of N at planting and the other half when plant heights were 50 cm) 15 N labelled urea (2.63 % 15 N a.e. as 120 kg N/ha) was applied. After harvesting, total N and 15 N analyses were done for plant and soil samples. The results showed that the seed and total yields were increased with higher (360 mm) irrigation. When N application was side dressed the availability of N was increased, and also its loss by leaching from the active root zone was decreased. In conclusion, it was observed that at high irrigation rate was saved about 84 kg N/ha by side dressing rather than broadcasting of the applied N fertilizer

  7. Chemical determination of free radical-induced damage to DNA.

    Science.gov (United States)

    Dizdaroglu, M

    1991-01-01

    Free radical-induced damage to DNA in vivo can result in deleterious biological consequences such as the initiation and promotion of cancer. Chemical characterization and quantitation of such DNA damage is essential for an understanding of its biological consequences and cellular repair. Methodologies incorporating the technique of gas chromatography/mass spectrometry (GC/MS) have been developed in recent years for measurement of free radical-induced DNA damage. The use of GC/MS with selected-ion monitoring (SIM) facilitates unequivocal identification and quantitation of a large number of products of all four DNA bases produced in DNA by reactions with hydroxyl radical, hydrated electron, and H atom. Hydroxyl radical-induced DNA-protein cross-links in mammalian chromatin, and products of the sugar moiety in DNA are also unequivocally identified and quantitated. The sensitivity and selectivity of the GC/MS-SIM technique enables the measurement of DNA base products even in isolated mammalian chromatin without the necessity of first isolating DNA, and despite the presence of histones. Recent results reviewed in this article demonstrate the usefulness of the GC/MS technique for chemical determination of free radical-induced DNA damage in DNA as well as in mammalian chromatin under a vast variety of conditions of free radical production.

  8. Effects of extraction methods on the yield, chemical structure and anti-tumor activity of polysaccharides from Cordyceps gunnii mycelia.

    Science.gov (United States)

    Zhu, Zhen-Yuan; Dong, Fengying; Liu, Xiaocui; Lv, Qian; YingYang; Liu, Fei; Chen, Ling; Wang, Tiantian; Wang, Zheng; Zhang, Yongmin

    2016-04-20

    This study was to investigate the effects of different extraction methods on the yield, chemical structure and antitumor activity of polysaccharides from Cordyceps gunnii (C. gunnii) mycelia. Five extraction methods were used to extract crude polysaccharides (CPS), which include room-temperature water extraction (RWE), hot-water extraction (HWE), microwave-assisted extraction (MAE), ultrasound-assisted extraction (UAE) and cellulase-assisted extraction (CAE). Then Sephadex G-100 was used for purification of CPS. As a result, the antitumor activities of CPS and PPS on S180 cells were evaluated. Five CPS and purified polysaccharides (PPS) were obtained. The yield of CPS by microwave-assisted extraction (CPSMAE) was the highest and its anti-tumor activity was the best and its macromolecular polysaccharide (3000-1000kDa) ratio was the largest. The PPS had the same monosaccharide composition, but their obvious difference was in the antitumor activity and the physicochemical characteristics, such as intrinsic viscosity, specific rotation, scanning electron microscopy and circular dichroism spectra. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. Acid-yield measurements of the gas-phase ozonolysis of ethene as a function of humidity using Chemical Ionisation Mass Spectrometry (CIMS

    Directory of Open Access Journals (Sweden)

    K. E. Leather

    2012-01-01

    Full Text Available Gas-phase ethene ozonolysis experiments were conducted at room temperature to determine formic acid yields as a function of relative humidity (RH using the integrated EXTreme RAnge chamber-Chemical Ionisation Mass Spectrometry technique, employing a CH3I ionisation scheme. RHs studied were <1, 11, 21, 27, 30 % and formic acid yields of (0.07±0.01 and (0.41±0.07 were determined at <1 % RH and 30 % RH respectively, showing a strong water dependence. It has been possible to estimate the ratio of the rate coefficient for the reaction of the Criegee biradical, CH2OO with water compared with decomposition. This analysis suggests that the rate of reaction with water ranges between 1×10−12–1×10−15 cm3 molecule−1 s−1 and will therefore dominate its loss with respect to bimolecular processes in the atmosphere. Global model integrations suggest that this reaction between CH2OO and water may dominate the production of HC(OOH in the atmosphere.

  10. Determination of the compressive yield strength for nano-grained YAG transparent ceramic by XRD analysis

    International Nuclear Information System (INIS)

    Wang, H.M.; Jiang, J.S.; Huang, Z.Y.; Chen, Y.; Liu, K.; Lu, Z.W.; Qi, J.Q.; Li, F.; He, D.W.; Lu, T.C.; Wang, Q.Y.

    2016-01-01

    Nano-grained ceramics have their unique mechanical characteristics that are not commonly found in their coarse-grained counterparts. In this study, nano-grained YAG transparent ceramics (NG-YAG) were prepared by low-temperature high-pressure technique (LTHP). The peak profile analysis of the X-ray diffraction was employed to investigate the compressive yield strength of NG-YAG. During the temperature at 450 °C, the residual micro-strain (RMS) increased with increasing loading pressure. However when the loading pressure was exceeded to 4.0 GPa the RMS exhibited a severe negative slop. The temperature effects on the compressive yield strength were also studied. It shows that the compressive yield strength of NG-YAG is 4.0 GPa and 5.0 GPa respectively at 450 °C and 350 °C. More importantly according to this investigation, a feasible technique to study the nano-grained ceramics is provided. - Graphical abstract: Fig. 2 shows the significant slope changes of calculated residual micro-strain (RMS) associated with five selected pressure-temperature conditions. Another the grain size estimated from Scherrer's formula, especially when it changes with the pressure-temperature condition is also plotted in Fig. 2. - Highlights: • Prepared the nano-grained YAG transparent ceramic by high pressure technique. • Obtained the compressive yield with different temperature. • Obtained the compressive yield of nano-grained YAG transparent ceramic.

  11. Proton chemical shift tensors determined by 3D ultrafast MAS double-quantum NMR spectroscopy

    International Nuclear Information System (INIS)

    Zhang, Rongchun; Mroue, Kamal H.; Ramamoorthy, Ayyalusamy

    2015-01-01

    Proton NMR spectroscopy in the solid state has recently attracted much attention owing to the significant enhancement in spectral resolution afforded by the remarkable advances in ultrafast magic angle spinning (MAS) capabilities. In particular, proton chemical shift anisotropy (CSA) has become an important tool for obtaining specific insights into inter/intra-molecular hydrogen bonding. However, even at the highest currently feasible spinning frequencies (110–120 kHz), 1 H MAS NMR spectra of rigid solids still suffer from poor resolution and severe peak overlap caused by the strong 1 H– 1 H homonuclear dipolar couplings and narrow 1 H chemical shift (CS) ranges, which render it difficult to determine the CSA of specific proton sites in the standard CSA/single-quantum (SQ) chemical shift correlation experiment. Herein, we propose a three-dimensional (3D) 1 H double-quantum (DQ) chemical shift/CSA/SQ chemical shift correlation experiment to extract the CS tensors of proton sites whose signals are not well resolved along the single-quantum chemical shift dimension. As extracted from the 3D spectrum, the F1/F3 (DQ/SQ) projection provides valuable information about 1 H– 1 H proximities, which might also reveal the hydrogen-bonding connectivities. In addition, the F2/F3 (CSA/SQ) correlation spectrum, which is similar to the regular 2D CSA/SQ correlation experiment, yields chemical shift anisotropic line shapes at different isotropic chemical shifts. More importantly, since the F2/F1 (CSA/DQ) spectrum correlates the CSA with the DQ signal induced by two neighboring proton sites, the CSA spectrum sliced at a specific DQ chemical shift position contains the CSA information of two neighboring spins indicated by the DQ chemical shift. If these two spins have different CS tensors, both tensors can be extracted by numerical fitting. We believe that this robust and elegant single-channel proton-based 3D experiment provides useful atomistic-level structural and dynamical

  12. Effect of Azolla Based - Organic Fertilizer, Rock Phosphate and Rice Hull Ash on Rice Yield and Chemical Properties of Alfisols

    Directory of Open Access Journals (Sweden)

    Sudadi

    2014-07-01

    Full Text Available The application of chemical fertilizer for long time may adverse soil environment. Organic agriculture, for example combination use of azolla based-organic fertilizer, phosphate rock and rice hull ash, was one of ways that able to recover it. Research was conducted in Sukosari, Jumantono, Karanganyar while soi chemical properties analysis was analysed in Soil Chemistry and Fertility Laboratory, Fac. of Agriculture, Sebelas Maret University April to November 2013. Research design used was RAKL with 5 treatments, each repeated 5 times. The treatments applied were P0 (control, P1 ( azola inoculum dosage 250 g/m2 + phosphate rock + rice hull ash equal to 150 kg/ha KCl, P2 (azola inoculum dosage 500 g/m2 + phosphate rock equal to 150kg/ha, SP-36 + rice hull ash equal to 100 kg/ha KCl, P3 (manure dosage of 5 ton/ha,P4 (Urea 250 kg/ha + SP-36 150 kg/ha + KCl 100 kg/ha. Data analysed statistically by F test (Fisher test with level of confident 95% followed by DMRT (Duncan Multiple Range Test if any significant differences. The result showed that the treatment combination of azolla, phosphate rock and rice hull ash increase soil organic matter content, cation exchange capacity, available-P and exchangeable-K as well as rice yield ( (at harvest-dry grain weight and milled-dry grain weight.

  13. The Growth and Yield of Sweet Corn Fertilized by Dairy Cattle Effluents Without Chemical Fertilizers in Inceptisols

    Directory of Open Access Journals (Sweden)

    Yudi Sastro

    2011-05-01

    Full Text Available Several research has proven the role of dairy cattle effluents in improving the growth and yield of some crops. However, its role in supporting the growth and yield of sweet corn, especialy in Inceptisols, has not been reported. The study aims to determine the effect of dairy cattle effluents on growth and yield of sweet corn in Inceptisols. The pot study was conducted in a greenhouse of the Assessment Institute for Agriculture Technology of Jakarta. The treatments were fertilization using dairy cattle effluents (without dilution, dilution with water 1:1 and 1:2, a mixture of Urea, SP-36 and KCl (NPK, and without fertilizer. The experimental design was a completely randomized design with five replications. Compared to a without fertilizer treatment, dairy cattle effluents were significantly increased plant height (114%, leaf number (136%, cob weight (131%, cob length (124%, and cob diameters (128%. Base on cob weight, relative agronomic effectiveness (RAE of dairy cattle effluents reached 38.4% (without dilution, 47.5% (dilution with water 1:1, and 62.1% (dilution with water 1:2.

  14. Determination of the ultimate load in concrete slabs by the yield line finite element method

    International Nuclear Information System (INIS)

    Vaz, L.E.; Feijo, B.; Martha, L.F.R.; Lopes, M.M.

    1984-01-01

    A method for calculating the ultimate load in reinforced concrete slabs is proposed. The method follows the finite element aproach representating the continuum slab as an assembly of rigid triangular plates connected along their sides through yield line elements. This approach leads to the definition of the displacement configuration of the plate only as a function of the transversal displacement at the nodes of the mesh (1 DOF per node) reducing significantly the number of DOF's in relation to the conventional formulation by means of the finite element method (minimum of 3 DOF per node). Nonlinear behaviour of the reinforced concrete section is considered in the definition of the moment rotation curve of the yield lines. The effect of the in plane forces acting in the middle surface of the plate is also taken into account. The validity of the model is verified comparing the numerical solutions with the results of the classical yield line theory. (Author) [pt

  15. [Yield and chemical composition of the vegetal parts of the amaranth (Amaranthus hypochondriacus, L.) at different physiological stages].

    Science.gov (United States)

    Alfaro, M A; Martínez, A; Ramírez, R; Bressani, R

    1987-03-01

    The genus Amaranthus comprises species which, consumed as vegetables, provide essential nutrients to man; they also have a high acceptability among the population. These two factors justify the need to increase their cultivation. Therefore, the purpose of this research was to establish the most adequate physiological state of maturity, to harvest the leaves for human consumption. The field experiment utilized a randomized block design with three treatments and eight replications. These treatments consisted in harvesting the plants at 25, 40 and 60 days after emergence of the seedlings, samples which served to evaluate: plant height, number of leaves, leaf surface area, gross weight (leaves and stems), net weight (leaves), green matter and dry matter yield, as well as protein. The chemical composition of the harvested material was evaluated also in terms of moisture, protein, crude fiber, ether extract, ash, carbohydrate, calcium, phosphorus, iron, beta-carotene and oxalates. The results obtained in the agronomic study were subjected to analysis of variance for the respective design, with significant differences found between treatments for all the variables studied. In its turn, the results of the chemical analysis were analyzed by a completely randomized design, with significant differences obtained for most of the variables studied, except for ether extract, calcium, iron and oxalates. From the nutritional point of view, the first harvest was the most acceptable due to the chemical composition of the plant, in particular protein (29.5%), beta-carotene (33.7 mg%), calcium (2,356.1 mg%), phosphorus (759.1 mg%) and due to its low crude fiber content, only 11.1 g%. It did not occur so from the agronomic point of view, since during this stage, very low yields of green matter (575.9 kg/ha), dry matter (66.6 kg/ha) and protein (19.7 kg/ha) were obtained. At the second harvest, besides obtaining adequate yields of green matter (6,530.4 kg/ha), dry matter (681.8 kg

  16. Determination of Yield and Yield Components as a Second Crop of Some Sesame Genotypes Collected from Şanlıurfa Region

    Directory of Open Access Journals (Sweden)

    Hüseyin ARSLAN

    2014-09-01

    Full Text Available This research, was carried out to determine the performance of some sesame (Sesamum indicum L. lines/genotype (15 and Arslanbey, Özberk-82, Muganlı-57, Gölmarmara and Baydar-2001 standard varieties in the Southeastern Anatolia Region. The studies were conducted at two locations (GAP Agricultural Research Institute-Gündaş Research Station and Talat Demirören Research Station during the growing season in 2010 (13 lines/genotype and 2011 (15 lines/genotype. Trials randomized complete block design as three replications. Plots length were 6 m, each plot formed 4 rows, row spacing was 70 cm and row distance was 15 cm. In the experiments was taken plant height, number of lateral branches per plant, number of capsules per plant, seed yield and 1000-grain weight as the herbal properties of the observations. According to research results; Arslanbey sesame variety with amounts ranging from 1112 kg ha-1 to 548 kg ha- 1 seed yield, in Şanlıurfa climate and soil conditions as the second product compared to other prominent varieties and lines is easily recommended.

  17. Pair copula constructions to determine the dependence structure of Treasury bond yields

    Directory of Open Access Journals (Sweden)

    Marcelo Brutti Righi

    2015-12-01

    Full Text Available We estimated the dependence structure of US Treasury bonds through a pair copula construction. As a result, we verified that the variability of the yields decreases with a longer time of maturity of the bond. The yields presented strong dependence with past values, strongly positive bivariate associations between the daily variations, and prevalence of the Student's t copula in the relationships between the bonds. Furthermore, in tail associations, we identified relevant values in most of the relationships, which highlights the importance of risk management in the context of bonds diversification.

  18. Determination of some chemical and microbiological characteristics of Kaymak

    Directory of Open Access Journals (Sweden)

    Ökten, Sevtap

    2006-12-01

    Full Text Available Kaymak is a kind of concentrated cream, which is traditionally manufactured from buffalo or cow’s milk in Turkey. It is generally consumed with honey at breakfast and some traditional Turkish desserts. The aim of this study was to determine some chemical and microbiological properties of kaymak. The samples were obtained from different dairy plants producing kaymak from cow’s milk and local markets located in Zmir. They were examined for total solids and fat contents, acidity, pH and peroxide values, as well as counts of coliform bacteria, E. coli, yeast and moulds, and Staphylococci. Chemical characteristics of the samples were generally favorable for Turkish Food Codex. However, microbiological properties of some samples were very poor. Careful considerations should be given by the kaymak industry during manufacturing and storage of the product.Kaymak es una clase de crema concentrada, que se fabrica tradicionalmente de la leche del búfalo o de la vaca en Turquía. Se consume generalmente con la miel en el desayuno y en algunos postres turcos tradicionales. El objetivo de este estudio fue determinar algunas características químicas y microbiológicas del kaymak. Las muestras fueron obtenidas de diversas instalaciones lecheras productoras de kaymak de leche de vaca y de mercados locales situados en Zmir. Se analizó el contenido en sólidos totales y grasas, acidez, pH y valores de peróxido, además del conteo de tan bien como cuentas de las bacterias coliformes, E. coli, levadura y mohos, y estafilococos. Las características químicas de las muestras fueron generalmente aceptables para el Turkish Food Codex. Sin embargo, las características microbiológicas de algunas muestras fueron muy malas. La industria del kaymak debe ser extremadamente cuidadosa durante la fabricación y el almacenaje del producto.

  19. Yield-determining factors in high-solids enzymatic hydrolysis of lignocellulose

    Directory of Open Access Journals (Sweden)

    Felby Claus

    2009-06-01

    Full Text Available Abstract Background Working at high solids (substrate concentrations is advantageous in enzymatic conversion of lignocellulosic biomass as it increases product concentrations and plant productivity while lowering energy and water input. However, for a number of lignocellulosic substrates it has been shown that at increasing substrate concentration, the corresponding yield decreases in a fashion which can not be explained by current models and knowledge of enzyme-substrate interactions. This decrease in yield is undesirable as it offsets the advantages of working at high solids levels. The cause of the 'solids effect' has so far remained unknown. Results The decreasing conversion at increasing solids concentrations was found to be a generic or intrinsic effect, describing a linear correlation from 5 to 30% initial total solids content (w/w. Insufficient mixing has previously been shown not to be involved in the effect. Hydrolysis experiments with filter paper showed that neither lignin content nor hemicellulose-derived inhibitors appear to be responsible for the decrease in yields. Product inhibition by glucose and in particular cellobiose (and ethanol in simultaneous saccharification and fermentation at the increased concentrations at high solids loading plays a role but could not completely account for the decreasing conversion. Adsorption of cellulases was found to decrease at increasing solids concentrations. There was a strong correlation between the decreasing adsorption and conversion, indicating that the inhibition of cellulase adsorption to cellulose is causing the decrease in yield. Conclusion Inhibition of enzyme adsorption by hydrolysis products appear to be the main cause of the decreasing yields at increasing substrate concentrations in the enzymatic decomposition of cellulosic biomass. In order to facilitate high conversions at high solids concentrations, understanding of the mechanisms involved in high-solids product inhibition

  20. Determination of the optimum pressure for neutron yield with d2, in the PF facility dena

    International Nuclear Information System (INIS)

    Siahpoush, V.; Khorram, C.; Sobhanian, S.; Hamzeh Fafreshi, M. A.

    2003-01-01

    Using physical model, which describes the dynamics of plasma in the Filipov type plasma focus, we have simulated the pinch current for different voltages and pressures. The results show that for a specific voltage, there is an optimum pressure for which the pinch current has maximum value. A comparison between the simulated and the experimental data from dena shows that the maximum values of pinch current are obtained at the same pressure for which the maximum neutron yield is observed

  1. Determination of lower bound crystallographic yield loci of zircaloy-4 tubes

    International Nuclear Information System (INIS)

    Costa Viana, C.S. da

    1980-01-01

    The use of zircaloy-4 tubing in fuel elements of water cooled reactors is discussed with respect to its mechanisms of deformation and also its resulting anisotropic plastic behaviour. A method for obtaining lower bound crystallographic yield loci of α-Zr is presented and applied to individual crystal orientations and to a real texture described by the main components observed on a direct pole figure. (Author) [pt

  2. Nuclear Weapon Yield Determination through Nano Indentation of Thermally Degraded Automobile Paint

    Science.gov (United States)

    2011-03-01

    function of the layer. When less complicated paint systems were used, the primer filled the role of surfacer. As each layer of paint became more...majority of the property changes caused by the irradiation would be near the surface. Unfortunately, surface effects are complicated , difficult...are two values recorded in the bubble and whitening rows under the Highest Temperature not Observed because the experiment that yielded the

  3. Convenient determination of luminescence quantum yield using a combined electronic absorption and emission spectrometer

    Energy Technology Data Exchange (ETDEWEB)

    Prakash, John; Mishra, Ashok Kumar [Department of Chemistry, Indian Institute of Technology Madras, Chennai 600036 (India)

    2016-01-15

    It is possible to measure luminescence quantum yield in a facile way, by designing an optical spectrometer capable of obtaining electronic absorption as well as luminescence spectra, with a setup that uses the same light source and detector for both the spectral measurements. Employment of a single light source and single detector enables use of the same correction factor profile for spectral corrections. A suitable instrumental scaling factor is used for adjusting spectral losses.

  4. Efficient sampling to determine distribution of fruit quality and yield in a commercial apple orchard

    DEFF Research Database (Denmark)

    Martinez Vega, Mabel Virginia; Wulfsohn, D.; Zamora, I.

    2012-01-01

    In situ assessment of fruit quality and yield can provide critical data for marketing and for logistical planning of the harvest, as well as for site-specific management. Our objective was to develop and validate efficient field sampling procedures for this purpose. We used the previously reported...... ‘fractionator’ tree sampling procedure and supporting handheld software (Gardi et al., 2007; Wulfsohn et al., 2012) to obtain representative samples of fruit from a 7.6-ha apple orchard (Malus ×domestica ‘Fuji Raku Raku’) in central Chile. The resulting sample consisted of 70 fruit on 56 branch segments...... of yield. Estimated marketable yield was 295.8±50.2 t. Field and packinghouse records indicated that of 348.2 t sent to packing (52.4 t or 15% higher than our estimate), 263.0 t was packed for export (32.8 t less or -12% error compared to our estimate). The estimated distribution of caliber compared very...

  5. Efficient sampling to determine the distribution of fruit quality and yield in a commercial apple orchard

    DEFF Research Database (Denmark)

    Martinez, M.; Wulfsohn, Dvora-Laio; Zamora, I.

    2012-01-01

    In situ assessment of fruit quality and yield can provide critical data for marketing and for logistical planning of the harvest, as well as for site-specific management. Our objective was to develop and validate efficient field sampling procedures for this purpose. We used the previously reported...... 'fractionator' tree sampling procedure and supporting handheld software (Gardi et al., 2007; Wulfsohn et al., 2012) to obtain representative samples of fruit from a 7.6-ha apple orchard (Malus ×domestica 'Fuji Raku Raku') in central Chile. The resulting sample consisted of 70 fruit on 56 branch segments...... of yield. Estimated marketable yield was 295.8±50.2 t. Field and packinghouse records indicated that of 348.2 t sent to packing (52.4 t or 15% higher than our estimate), 263.0 t was packed for export (32.8 t less or -12% error compared to our estimate). The estimated distribution of caliber compared very...

  6. Impact of mechanical, chemical and enzymatic pre-treatments on the methane yield from the anaerobic digestion of switchgrass

    International Nuclear Information System (INIS)

    Frigon, Jean-Claude; Mehta, Punita; Guiot, Serge R.

    2012-01-01

    The conversion of cellulosic crops into biofuels, including methane, is receiving a lot of attention lately. Panicum vergatum, or switchgrass, is a warm season perennial grass well adapted to grow in North America. Different pre-treatments were tested in 0.5 l batch reactors, at 35 °C, in order to enhance the methane production from switchgrass, including temperature, sonication, alkalinization and autoclaving. The methane production on the basis of volatile solids (VS) added to the fermentation were 112.4 ± 8.4, 132.5 ± 9.7 and 139.8 ml g −1 after 38 days of incubation for winter harvested switchgrass (WHS) after grinding, grinding with alkalinization, and grinding with alkalinization and autoclaving, respectively. The methane production was higher for fresh summer harvested switchgrass (SHS), with a production of 256.6 ± 8.2 ml g −1 VS after mulching, alkalinization and autoclaving. The methane production from SHS was improved by 29 and 42% when applying lignin (LiP) or manganese peroxidase (MnP), at 202.1 ± 9.8 and 222.9 ± 22.5 ml g −1 VS, respectively. The combination of an alkali pre-treatment with the MnP increased the methane production furthermore at 297.7 ml g −1 VS. The use of pectinases without chemical pre-treatment showed promising yields at 287.4 and 239.5 ml g −1 VS for pectate-lyase and poly-galacturonase, respectively. An estimation of the methane yield per hectare of crop harvested resulted in net energy production of 29.8, 49.7 and 78.1 GJ for winter harvested switchgrass, mulched and pretreated summer harvested switchgrass, respectively. Switchgrass represents an interesting candidate as a lignocellulosic crop for methane production. -- Highlights: ► Switchgrass is a model energy crops for biofuels production. ► This study evaluated different pre-treatments to enhance methane production. ► Pre-treatments increase significantly the methane produced from switchgrass. ► Enzymatic pre-treatments were superior to physical and

  7. Determination of the fission products yields, lanthanide and yttrium, in the fission of 238U with neutrons of fission spectra

    International Nuclear Information System (INIS)

    Nicoli, I.G.

    1981-06-01

    A radiochemical investigation is performed to measure the cumulative fission product yields of several lantanides and yttrium nuclides in the 238 U by fission neutron spectra. Natural and depleted uranium are irradiated under the same experimental conditions in order to find a way to subtract the contribution of the 235 U fission. 235 U percentage in the natural uranium was 3.5 times higher than in the depleted uranium. Uranium oxides samples are irradiated inside the core of the Argonaut Reactor, at the Instituto de Engenharia Nuclear, and the lantanides and yttrium are chemically separated. The fission products gamma activities were detected, counted and analysed in a system constituted by a high resolution Ge(Li) detector, 4096 multichannel analyser and a PDP-11 computer. Cumulative yields for fission products with half-lives between 1 to 33 hours are measured: 93 Y, 141 La, 142 La, 143 Ce and 149 Nd. The chain total yields are calculated. The cumulative fission yields measured for 93 Y, 141 La, 142 La, 143 Ce and 149 Nd are 4,49%, 4,54%, 4,95%, 4,16% and 1,37% respectively and they are in good agreement with the values found in the literature. (Author) [pt

  8. Impact of vetch cover crop on runoff, soil loss, soil chemical properties and yield of chickpea in North Gondar, Ethiopia

    Science.gov (United States)

    Demelash, Nigus; Klik, Andreas; Holzmann, Hubert; Ziadat, Feras; Strohmeier, Stefan; Bayu, Wondimu; Zucca, Claudio; Abera, Atikilt

    2016-04-01

    Cover crops improve the sustainability and quality of both natural system and agro ecosystem. In Gumara-Maksegnit watershed which is located in Lake Tana basin, farmers usually use fallow during the rainy season for the preceding chickpea production system. The fallowing period can lead to soil erosion and nutrient losses. A field experiment was conducted during growing seasons 2014 and 2015 to evaluate the effect of cover crops on runoff, soil loss, soil chemical properties and yield of chickpea in North Gondar, Ethiopia. The plot experiment contained four treatments arranged in Randomized Complete Block Design with three replications: 1) Control plot (Farmers' practice: fallowing- without cover crop), 2) Chickpea planted with Di-ammonium phosphate (DAP) fertilizer with 46 k ha-1 P2O5 and 23 k ha-1 nitrogen after harvesting vetch cover crop, 3) Chick pea planted with vetch cover crop incorporated with the soil as green manure without fertilizer, 4) Chick pea planted with vetch cover crop and incorporated with the soil as green manure and with 23 k ha-1 P2O5 and 12.5 k ha-1 nitrogen. Each plot with an area of 36 m² was equipped with a runoff monitoring system. Vetch (Vicia sativa L.) was planted as cover crop at the onset of the rain in June and used as green manure. The results of the experiment showed statistically significant (P plant, above ground biomass and grain yield of chick pea. However, there was no statistically significant difference (P > 0.05) on average plant height, average number of branches and hundred seed weight. Similarly, the results indicated that cover crop has a clear impact on runoff volume and sediment loss. Plots with vetch cover crop reduce the average runoff by 65% and the average soil loss decreased from 15.7 in the bare land plot to 8.6 t ha-1 with plots covered by vetch. In general, this result reveales that the cover crops, especially vetch, can be used to improve chickpea grain yield in addition to reduce soil erosion in the

  9. The Effect of Organic and Chemical Fertilizers on Qualitative and Quantitative Yield of Indigo (Indigofera tinctoria L. at Irrigation Levels under Bam Climatic Conditions

    Directory of Open Access Journals (Sweden)

    N Modafe Behzadi

    2018-05-01

    and Discussion The results showed that at the first and second cuttings, the highest dry weight of leaf (with 751.11 and 769.24 g m-2, respectively and indigocarmin yield (with 4.62 and 4.66 g.m-2, respectively were observed for vermicopmost. Increasing soil water content from 60 to 100% FC at the first and second cuttings caused to increase dry weight of leaf (with 37 and 100%, respectively. Decreasing soil water content caused to reduce the dry matter yield of indigo and these highest yields were obtained in 100% FC with 1589.3 and 1829.3 g m-2, respectively. Also, increasing soil water content from 60 to 100% FC caused that indigocarmin content and indigocarmin yield increased with 36 and 18%, respectively. Relationship between soil nutrients and metabolic processes of medicinal plants causes to change of yield quantity or secondary metabolites contents. Therefore, we determined that the best growth condition for indigo was observed for manure and irrigation based on 80% FC. Conclusions It was concluded that cow manure could be a good choice for decreasing chemical fertilization application.

  10. Development of a Chemically Defined Medium for Better Yield and Purification of Enterocin Y31 from Enterococcus faecium Y31

    Directory of Open Access Journals (Sweden)

    Wenli Liu

    2017-01-01

    Full Text Available The macro- and micronutrients in traditional medium, such as MRS, used for cultivating lactic acid bacteria, especially for bacteriocin production, have not been defined, preventing the quantitative monitoring of metabolic flux during bacteriocin biosynthesis. To enhance Enterocin Y31 production and simplify steps of separation and purification, we developed a simplified chemically defined medium (SDM for the growth of Enterococcus faecium Y31 and production of its bacteriocin, Enterocin Y31. We found that the bacterial growth was unrelated to Enterocin Y31 production in MRS; therefore, both the growth rate and the Enterocin Y31 production were set as the index for investigation. Single omission experiments revealed that 5 g/L NaCl, five vitamins, two nucleic acid bases, MgSO4·7H2O, MnSO4·4H2O, KH2PO4, K2HPO4, CH3COONa, fourteen amino acids, and glucose were essential for the strain’s growth and Enterocin Y31 production. Thus, a novel simplified and defined medium (SDM was formulated with 30 components in total. Consequently, Enterocin Y31 production yield was higher in SDM as compared to either MRS or CDM. SDM improved the Enterocin Y31 production and simplified the steps of purification (only two steps, which has broad potential applications.

  11. A simple theoretical approach to determine relative ion yield (RIY) in glow discharge mass spectrometry (GDMS)

    Energy Technology Data Exchange (ETDEWEB)

    Born, Sabine [Degussa AG, Hanau (Germany); Matsunami, Noriaki [Nagoya Univ. (Japan). Faculty of Engineering; Tawara, Hiroyuki [National Inst. for Fusion Science, Toki, Gifu (Japan)

    2000-01-01

    Direct current glow discharge mass spectrometry (dc-GDMS) has been applied to detect impurities in metals. The aim of this study is to understand quantitatively the processes taking place in GDMS and establish a model to calculate the relative ion yield (RIY), which is inversely proportional to the relative sensitivity factor (RSF), in order to achieve better agreement between the calculated and the experimental RIYs. A comparison is made between the calculated RIY of the present model and the experimental RIY, and also with other models. (author)

  12. Why is it so difficult to determine the yield of indoor cannabis plantations? A case study from the Netherlands.

    Science.gov (United States)

    Vanhove, Wouter; Maalsté, Nicole; Van Damme, Patrick

    2017-07-01

    Together, the Netherlands and Belgium are the largest indoor cannabis producing countries in Europe. In both countries, legal prosecution procedure of convicted illicit cannabis growers usually includes recovery of the profits gained. However, it is not easy to make a reliable estimation of the latter profits, due to the wide range of factors that determine indoor cannabis yields and eventual selling prices. In the Netherlands, since 2005, a reference model is used that assumes a constant yield (g) per plant for a given indoor cannabis plant density. Later, in 2011, a new model was developed in Belgium for yield estimation of Belgian indoor cannabis plantations that assumes a constant yield per m 2 of growth surface, provided that a number of growth conditions are met. Indoor cannabis plantations in the Netherlands and Belgium share similar technical characteristics. As a result, for indoor cannabis plantations in both countries, both aforementioned yield estimation models should yield similar yield estimations. By means of a real-case study from the Netherlands, we show that the reliability of both models is hampered by a number of flaws and unmet preconditions. The Dutch model is based on a regression equation that makes use of ill-defined plant development stages, assumes a linear plant growth, does not discriminate between different plantation size categories and does not include other important yield determining factors (such as fertilization). The Belgian model addresses some of the latter shortcomings, but its applicability is constrained by a number of pre-conditions including plantation size between 50 and 1000 plants; cultivation in individual pots with peat soil; 600W (electrical power) assimilation lamps; constant temperature between 20°C and 30°C; adequate fertilizer application and plants unaffected by pests and diseases. Judiciary in both the Netherlands and Belgium require robust indoor cannabis yield models for adequate legal prosecution of

  13. Changes in Soil Chemical Properties and Lettuce Yield Response Following Incorporation of Biochar and Cow Dung to Highly Weathered Acidic Soils

    DEFF Research Database (Denmark)

    Agyei Frimpong, Kwame; Amoakwah, Emmanuel; Osei, Benjamin A

    2016-01-01

    imposed on two highly weathered, acidic soils from the coastal savanna and tropical rainforest agroecological zones of Ghana, respectively, to elucidate their effect on yield of lettuce. The study showed that application of biochar solely or in combination with cow dung increased soil pH, total organic...... carbon, and cation exchange capacity, and temporarily increased soil respiration and microbial biomass carbon. Further, incorporation of combined application of cow dung and biochar increased lettuce yield more than sole incorporation of either amendment. The study demonstrated that corn cob biochar can...... improve soil chemical properties and lettuce yield if applied solely or in combination with cow dung....

  14. Yield Loss Assessment and Determination of Control Thresholds for Anthracnose on Red Pepper

    Directory of Open Access Journals (Sweden)

    Ju-Hee Kim

    2015-03-01

    Full Text Available This study was carried out to develop control thresholds for anthracnose on red pepper. To investigate relationship between anthracnose incidence and diseased fruits, experimental plots with six treatments were established. There existed close correlation between rate of diseased fruits and yields in field (Y = -16.83X + 327.57, R² = 0.83, in rain shelter (Y = -4.92X + 361.02, R² = 0.84, and in rain shelter with rain (Y = -5.91X + 359.71, R² = 0.76. Control thresholds for anthracnose of pepper were 0.9% diseased fruits per plant in field and from 1.7 to 2.3% diseased fruits rate per plant in rain shelter.

  15. Effect of different methods of soil fertility increasing via application of organic, chemical and biological fertilizers on grain yield and quality of canola (Brassica napus L.

    Directory of Open Access Journals (Sweden)

    K. Mohammadi

    2016-05-01

    Full Text Available Different resource of fertilizers had an effect on grain yield, oil and grain quality. Information regarding the effect of simultaneous application of organic, chemical and biological fertilizers on canola (Brassica napus L. traits is not available. In order to study the effect of different systems of soil fertility on grain yield and quality of canola (Talayeh cultivar, an experiment was conducted at experimental farm of Agricultural Research Center of Sanandaj, Iran, during two growing seasons of 2007-2008 and 2008-2009. The experimental units were arranged as split plots based on randomized complete blocks design with three replications. Main plots consisted of five methods for obtaining the basal fertilizers requirement including (N1: farm yard manure; (N2: compost; (N3: chemical fertilizers; (N4: farm yard manure + compost and (N5: farm yard manure + compost + chemical fertilizers; and control (N6. Sub plots consisted four levels of biofertilizers were (B1: Bacillus lentus and Pseudomonas putida; (B2: Trichoderma harzianum; (B3: Bacillus lentus and Pseudomonas putida and Trichoderma harzianum; and (B4: control, (without biofertilizers. Results showed that basal fertilizers and biofertilizers have a significant effect on grain yield. The highest grain yield was obtained from N5 treatment in which organic and chemical fertilizers were applied simultaneously applied. Basal fertilizers, biofertilizers have a significant effect on leaf chlorophyll. The highest nitrogen content (42.85 mg.g-1 and least amount of (N/S were obtained from N5 treatment. The highest oil percent was obtained from N1 and N2 treatments and highest oil yield was obtained from N5 treatment. Finally, application of organic manure and biofertilizers with chemical fertilizer led to an increase in yield and quality of canola grain.

  16. Using chemical benchmarking to determine the persistence of chemicals in a Swedish lake.

    Science.gov (United States)

    Zou, Hongyan; Radke, Michael; Kierkegaard, Amelie; MacLeod, Matthew; McLachlan, Michael S

    2015-02-03

    It is challenging to measure the persistence of chemicals under field conditions. In this work, two approaches for measuring persistence in the field were compared: the chemical mass balance approach, and a novel chemical benchmarking approach. Ten pharmaceuticals, an X-ray contrast agent, and an artificial sweetener were studied in a Swedish lake. Acesulfame K was selected as a benchmark to quantify persistence using the chemical benchmarking approach. The 95% confidence intervals of the half-life for transformation in the lake system ranged from 780-5700 days for carbamazepine to benchmarking approach agreed well with those from the mass balance approach (1-21% difference), indicating that chemical benchmarking can be a valid and useful method to measure the persistence of chemicals under field conditions. Compared to the mass balance approach, the benchmarking approach partially or completely eliminates the need to quantify mass flow of chemicals, so it is particularly advantageous when the quantification of mass flow of chemicals is difficult. Furthermore, the benchmarking approach allows for ready comparison and ranking of the persistence of different chemicals.

  17. Development of eggplant hybrid cultivar ‘BATEM FILIZI’ and determination of yield performance

    Directory of Open Access Journals (Sweden)

    Hatice Filiz BOYACI

    2014-12-01

    Full Text Available Eggplant (Solanum melongena L. cultivation is an important part of vegetable production in Turkey. It is highly affected by abiotic stress factors such as low temperatures during growth and development. The present study was aimed to improve new hybrid varieties with high quality and fruit setting under undesirable environmental conditions in eggplant. The 39 inbred lines were developed from eggplant genepool by using pedigree breeding method at the Bati Akdeniz Agricultural Research Institute. They were characterized morphologically and evaluated for phylogenetic relationship among them. Selected seven lines were crossed each other to obtain F1 hybrids. Thirteen hybrids from these crosses were examined for their rate of heterosis and heterobeltiosis. These hybrids were not suitable for market demands although F1 hybrids including P350 as parental line had high heterosis rate. Oval fruit shaped P350 inbred line as female parent showed good performance and crossed with long fruit shaped P599 inbred line. The resultant F1 hybrid cultivar higher yielding, suitable for production under greenhouse and highly adaptable was registered with the name of BATEM FILIZI. It is recommended that this hybrid can be used in greenhouse production especially in single crop season.

  18. Yield Perceptions, Determinants and Adoption Impact of on Farm Varietal Mixtures for Common Bean and Banana in Uganda

    Directory of Open Access Journals (Sweden)

    Rose Nankya

    2017-07-01

    Full Text Available Crop variety mixtures (different varieties of a crop grown together in a single plot have been successfully deployed in pathogen and pest management for several crops including wheat, common bean and rice. Despite the available evidence, promotion of this approach has remained limited in many countries, including Uganda. The factors that influence farmers’ adoption of varietal mixtures for common bean and banana were assessed, as well as the perceptions of farmers on the effects of mixtures on yields, through household surveys and statistical modelling. A three-year yield increase in both common bean and banana varietal mixtures in farmer fields, of 5.2% and 28.6%, respectively, is realized using robust OLS estimates. The study reveals that accessing knowledge on the importance of crop varietal mixtures and the skills relating to the approach are crucial for their adoption. Location of the farm significantly determined the perceived yield change, which calls for more research into mixtures’ suitability under particular contexts in respect to compatibility of genotypes, management practices and appropriate acreage for maximum impact. The positive effects of mixtures on yields make it an effective bioeconomy strategy. Policies that minimize the adoption barriers could improve the adoption of crop varietal mixtures on a wider scale.

  19. Yield stress determines bioprintability of hydrogels based on gelatin-methacryloyl and gellan gum for cartilage bioprinting

    Science.gov (United States)

    Mouser, Vivian H. M.; Melchels, Ferry P.W.; Visser, Jetze; Dhert, Wouter J.A.; Gawlitta, Debby; Malda, Jos

    2016-01-01

    Bioprinting of chondrocyte-laden hydrogels facilitates the fabrication of constructs with controlled organization and shape for e.g. articular cartilage implants. Gelatin-methacryloyl (gelMA) supplemented with gellan gum is a promising bio-ink. However, the rheological properties governing the printing process, and the influence of gellan gum on the mechanical properties and chondrogenesis of the blend, are still unknown. Here, we investigated the suitability of gelMA/gellan for cartilage bioprinting. Multiple concentrations, ranging from 3-25% gelMA with 0-1.5% gellan gum, were evaluated for their printability, defined as the ability to form filaments and to incorporate cells at 15-37°C. To support the printability assessment, yield stress and viscosity of the hydrogels were measured. Stiffness of UV-cured constructs, as well as cartilage-like tissue formation by embedded chondrocytes, were determined in vitro. A large range of gelMA/gellan concentrations were printable with inclusion of cells and formed the bioprinting window. Addition of gellan gum improved filament deposition by inducing yielding behavior, increased construct stiffness, and supported chondrogenesis. High gellan gum concentrations, however, did compromise cartilage matrix production and distribution, and even higher concentrations resulted in too high yield stresses to allow cell encapsulation. This study demonstrates the high potential of gelMA/gellan blends for cartilage bioprinting and identifies yield stress as dominant factor for bioprintability. PMID:27431733

  20. Yield stress determines bioprintability of hydrogels based on gelatin-methacryloyl and gellan gum for cartilage bioprinting.

    Science.gov (United States)

    Mouser, Vivian H M; Melchels, Ferry P W; Visser, Jetze; Dhert, Wouter J A; Gawlitta, Debby; Malda, Jos

    2016-07-19

    Bioprinting of chondrocyte-laden hydrogels facilitates the fabrication of constructs with controlled organization and shape e.g. for articular cartilage implants. Gelatin-methacryloyl (gelMA) supplemented with gellan gum is a promising bio-ink. However, the rheological properties governing the printing process, and the influence of gellan gum on the mechanical properties and chondrogenesis of the blend, are still unknown. Here, we investigated the suitability of gelMA/gellan for cartilage bioprinting. Multiple concentrations, ranging from 3% to 20% gelMA with 0%-1.5% gellan gum, were evaluated for their printability, defined as the ability to form filaments and to incorporate cells at 15 °C-37 °C. To support the printability assessment, yield stress and viscosity of the hydrogels were measured. Stiffness of UV-cured constructs, as well as cartilage-like tissue formation by embedded chondrocytes, were determined in vitro. A large range of gelMA/gellan concentrations were printable with inclusion of cells and formed the bioprinting window. The addition of gellan gum improved filament deposition by inducing yielding behavior, increased construct stiffness and supported chondrogenesis. High gellan gum concentrations, however, did compromise cartilage matrix production and distribution, and even higher concentrations resulted in too high yield stresses to allow cell encapsulation. This study demonstrates the high potential of gelMA/gellan blends for cartilage bioprinting and identifies yield stress as a dominant factor for bioprintability.

  1. Partial Least Squares Regression for Determining the Control Factors for Runoff and Suspended Sediment Yield during Rainfall Events

    Directory of Open Access Journals (Sweden)

    Nufang Fang

    2015-07-01

    Full Text Available Multivariate statistics are commonly used to identify the factors that control the dynamics of runoff or sediment yields during hydrological processes. However, one issue with the use of conventional statistical methods to address relationships between variables and runoff or sediment yield is multicollinearity. The main objectives of this study were to apply a method for effectively identifying runoff and sediment control factors during hydrological processes and apply that method to a case study. The method combines the clustering approach and partial least squares regression (PLSR models. The case study was conducted in a mountainous watershed in the Three Gorges Area. A total of 29 flood events in three hydrological years in areas with different land uses were obtained. In total, fourteen related variables were separated from hydrographs using the classical hydrograph separation method. Twenty-nine rainfall events were classified into two rainfall regimes (heavy Rainfall Regime I and moderate Rainfall Regime II based on rainfall characteristics and K-means clustering. Four separate PLSR models were constructed to identify the main variables that control runoff and sediment yield for the two rainfall regimes. For Rainfall Regime I, the dominant first-order factors affecting the changes in sediment yield in our study were all of the four rainfall-related variables, flood peak discharge, maximum flood suspended sediment concentration, runoff, and the percentages of forest and farmland. For Rainfall Regime II, antecedent condition-related variables have more effects on both runoff and sediment yield than in Rainfall Regime I. The results suggest that the different control factors of the two rainfall regimes are determined by the rainfall characteristics and thus different runoff mechanisms.

  2. Evaluation of the Effect of Sulfur Application and Thiobacillus on Some Soil Chemical Characteristics and Yield of Canola in Wheat-Canola Rotation System

    Directory of Open Access Journals (Sweden)

    H. Besharati

    2016-09-01

    Dep. of Soil and Water Research Institute. In this research treatments were applied in two separate sites (each site contains 24 plots which their dimensions were 2.4×10 meter. For evaluating the residual effect of treatments, the experiment was carried out in constant plots in second year. Phosphorus, iron, zinc, manganese and sulfate, were not applied to any of the treatments except for T8, and the above mentioned treatments were just received 250 kg urea. These all treatments were applied only in the first year and on the second year of experiment their Residual effects on canola were evaluated. During the growing season agricultural practices such as irrigation, weed and pest control in all units were managed uniformly. Soil chemical data were obtained by analyzing of Ec, pH and bicarbonate each year in May. The leaf and seed samples were taken for essential analysis. When plants growth completed, each plot was harvested separately then canola yield and also the phosphorus, iron and zinc content of shoots and grain were measured. Results: The results of two years indicated that the treatments had no significant effects on pH and bicarbonate of soil while increasing sulfur application rate, caused a decrease in soil bicarbonate content. In addition to that, the treatments did not affect the yield of canola significantly. In the first year of experiment, treatments had shown significant effects (P=0.01 on glucosinolates, seed sulfur and Cu of leaf, whereas no effect determination was occurred about indices of leaf and seed of canola. the results also suggested an increase of 800 kg in the sixth treatment (600 kg sulfur consumption without Thiobacillus and canola seed yield of treatment T6 enhancedfrom 3446 kg to 4531 kg per ha. Fertilization treatment (T8 could not increase canola yield, so it confirms that the nutrient concentration in experiment sites were near the critical level for canola. Conclusion: In total results revealed that different sulfur treatments

  3. Growth and yield of cucumber as influenced by compost and nitrogen fertilizer in sandy soils using the nuclear technique for determination of nitrogen

    International Nuclear Information System (INIS)

    El-Sherif, M.F.A.

    2005-01-01

    this study was carried out during the period from 2002 to 2003 seasons, at the department of plant research, Nuclear Research Center (NRC,) Atomic Energy Authority (AEA), Egypt, on cucumber plants c.v. dp007 F1 (wafer). the main objective of this work was to study the effect of compost type, application level and nitrogen rate on vegetative growth, chemical composition, early and total yield and to determine the fertilizer nitrogen uptake and utilization by the cucumber plant and its parts, i.e., shoots and fruits . results revealed that the sugar cane bagasse compost (SC) gave a significantly higher response with most vegetative growth expressed as plant length, leaf number and dry weight of cucumber plant, compared with beet compost (BC). the application of compost from 2 up to 6 ton/fed

  4. Natural radiation, radioactive waste and chemical risk determinants

    International Nuclear Information System (INIS)

    Christensen, T.; Mustonen, R.; Edhwall, H.; Hansen, H.; Soerensen, A.; Stranden, E.

    1990-01-01

    Doses from natural radiation to the population in the Nordic countries are summarized, and man-made modifications of the natural radiation environment are discussed. An account is given for the radiological concequences of energy concervation by reduced ventilation. Risks from possible future releases of radioactivity from final depositories of spent nuclear fuel are compared to the risks from present natural radioactivity in the environment. The possibilities for comparison between chemical and radiological risks are discussed. 104 refs., 36 figs., 47 tabs

  5. Determination of the {eta} mass from the production threshold for the {gamma}p {yields} p{eta} reaction

    Energy Technology Data Exchange (ETDEWEB)

    Nikolaev, Alexander

    2012-09-06

    This thesis is dedicated to a new precise determination of the {eta} meson mass based on a measurement of the threshold for the {gamma}p {yields} p{eta} reaction. This experiment was performed in the years 2004/2005 using the Crystal Ball/TAPS detector setup and the recently developed tagger focal-plane microscope detector at the MAMI-B facility in the Institut fuer Kernphysik of the Johannes Gutenberg-Universitaet Mainz. The real photon beam was produced by Bremsstrahlung of the 883 MeV electrons from MAMI-B on a thin diamond radiator. The {eta} mesons were identified via their two main decay modes, {eta} {yields} 2{gamma} and {eta} {yields} 3{pi}{sup 0}, with the Crystal Ball/TAPS setup, which measured energies and emission angles of particles. The identification of the {eta} {yields} 2{gamma} decay was performed using events with two clusters detected as photons, ignoring all other particles, and the standard invariant mass analysis. Cuts were applied on the invariant and missing mass distributions. The identification of the {eta} {yields} 3{pi}{sup 0} {yields} 6{gamma} decay concentrated on events with six clusters detected as photons. Among fifteen possible combinations of six photons to be arranged in three pairs, the combination with the smallest {chi}{sup 2}-value for the three pion masses was assumed to be correct. Cuts were applied on the {chi}{sup 2}-distribution and on the invariant and missing mass distributions. The normalization of the total cross section was obtained from the target thickness, the intensity of the photon flux, the simulated acceptance of the Crystal Ball, and the branching ratios of the {eta} decays. The determination of the {eta} mass required a very precise measurement of the production threshold. This was obtained by fitting the measured cross section as a function of photon energy and gave the result for the {eta} mass, m{sub {eta}}=(547.851{+-}0.031{sub stat.}{+-}0.062{sub syst.}) MeV.

  6. MR-fluid yield surface determination in disc-type MR rotary brakes

    International Nuclear Information System (INIS)

    Farjoud, Alireza; Vahdati, Nader; Fah, Yap Fook

    2008-01-01

    Magneto-rheological (MR) fluids are currently attracting a great deal of attention because of their unique rheological behavior. Many devices have been designed using MR fluids, and of potential interest here are disc-type MR rotary brakes. The plug flow region in MR devices is defined as the region where the fluid is not flowing. The plug flow region plays an important role in design and analysis of MR devices. In MR dampers, the damping coefficient is a function of the plug thickness. In MR valves, the plug thickness is used to control the flow rate through, and the pressure drop across, the MR valve. A MR clutch is performing at the highest efficiency when the entire MR gap is the plug region. For an MR rotary brake, the highest restraining torque is obtained when the entire gap is the plug region as far as there are no wall slip effects. In this paper, using the Bercovier and Engelman constitutive model, the MR fluid flow in disc-type MR brakes is modeled to determine the plug flow region. The resulting system of equations is solved numerically. It is shown that the existence of a plug flow region in the brake will affect the control torque ratio. Better estimation of the plug flow region results in better estimation of the viscous torque

  7. Determinants of Operational Efficiency at Chemical Cargo Terminals

    OpenAIRE

    T.A. Gúlcan; S. Esmer; Y. Zorba; G. Şengónúl

    2014-01-01

    In today’s globalized world, one of the requirements of global supply chains is efficient transportation systems. Approximately 80 per cent of world merchandise trade carried by sea and handled by ports worldwide. For this reason, maritime transport has the strategic economic importance. Loading of oil and gas has the biggest share (%30) in commodities carried by sea and 2.9 billion tons oil and gas loaded to ship in 2013. This study is focus on chemical cargo terminals which is a special ter...

  8. Tritium distributing in stainless steel determined by chemical etchin

    International Nuclear Information System (INIS)

    Xiong Yifu; Luo Deli; Chen Changan; Chen Shicun; Jing Wenyong

    2009-01-01

    The depth distribution of tritium in stainless steel was measured by chemical etching. The results show that the method can more quantitatively evaluate the tritium distributing in stainless steel. The maximum amount of tritium which distributed in crystal lattice of stainless steel is limitted by its solubility at room temperature. The other form of tritium in stainless steel is gaseous tritium that are trapped by defects, impurities, fractures, etc. within it. The gaseous tritium is several times more than the solid-dissolved tritium. (authors)

  9. Evaluation of indigenous rhizobacterial strains with reduced dose of chemical fertilizer towards growth and yield of mustard (Brassica campestris under old alluvial soil zone of West Bengal, India

    Directory of Open Access Journals (Sweden)

    Shampa Dutta

    2017-12-01

    Full Text Available A field experiment had been carried out in the Crop Research and Seed Multiplication Farm of The University of Burdwan, West Bengal, India during the two consecutive winter seasons of 2011-2012 and 2012-2013 to study the effect of indigenous rhizospheric bacterial strains on growth, physiology and yield of mustard variety. Pseudomonas putida, Burkholderia cepacia, Burkholderia sp. and their mixture were used as seed inoculants for mustard cultivation. The experiment was laid down in a randomized complete block design (RCBD with three replications. Results revealed that indigenous inoculation (with reduced dose of chemical fertilizer significantly increased (p < 0.05 the yield of mustard as compared to uninoculated control (full recommended dose of NPK fertilizers. A combination treatment of biofertilizer and chemical fertilizer also increased plant height, plant biomass and other yield components compared to control. The comprehensive approach of plant growth promoting rhizobacteria (PGPR in agriculturally important crops should be carried out to explore the hidden potential of PGPR and to promote the quality and yield of crop under field conditions. Keywords: Indigenous rhizobacteria, Mustard, PGPR, Yield

  10. Effects of Single and Combined Application of Organic, Biological and Chemical Fertilizers on Quantitative and Qualitative Yield of Coriander (Coriandrum sativum

    Directory of Open Access Journals (Sweden)

    M. Aghhavani Shajari

    2016-07-01

    Full Text Available Introduction: Medicinal plants were one of the main natural resources of Iran from ancient times. Coriander (Coriandrum sativum L. is from Apiaceae family that it has cultivated extensively in the world. Management and environmental factors such as nutritional management has a significant impact on the quantity and quality of plants. Application of organic fertilizers in conventional farming systems is not common and most of the nutritional need of plants supply through chemical fertilizers for short period. Excessive and unbalanced use of fertilizers in the long period, reduce crop yield and soil biological activity, accumulation of nitrates and heavy metals, and finally cause negative environmental effects and increase the cost of production. The use of bio-fertilizers and organic matter are taken into consideration to reduce the use of chemical fertilizers and increase the quality of most crops. Stability and soil fertility through the use of organic fertilizers are important due to having most of the elements required by plants and beneficial effects on physical, chemical, biological and soil fertility. Therefore, the aim of this research was to evaluate the effects of organic, biological and chemical fertilizers on quality and quantity characteristics of coriander. Materials and Methods: In order to study the effects of single and combined applications of organic, biological and chemical fertilizers on quantitative and qualitative characteristics of Coriander (Coriandrum sativum, an experiment was conducted based on a randomized complete block design with three replications and 12 treatments at Research Station, Faculty of Agriculture, Ferdowsi University of Mashhad, Iran, in - 2011. Treatments included: (1 mycorrhizae (Glomus mosseae (2 biosulfur (Thiobacillus sp., (3 chemical fertilizer (NPK, (4 cow manure, 5( vermin compost, 6( mycorrhizae + chemical fertilizer, 7( mycorrhizae + cow manure, 8( mycorrhizae + vermicompost, 9( biosulfur

  11. Analysis of determination modalities concerning the exposure and emission limits values of chemical and radioactive substances

    International Nuclear Information System (INIS)

    Schieber, C.; Schneider, T.

    2002-08-01

    This document presents the generic approach adopted by various organizations for the determination of the public exposure limits values to chemical and radioactive substances and for the determination of limits values of chemical products emissions by some installations. (A.L.B.)

  12. Determination of chemical states of sulphur 35 obtained from the 35Cl (n, p)35S

    International Nuclear Information System (INIS)

    Rossi Filho, S.

    1980-01-01

    The chemical states of sulphur-35 obtained from the 35 Cl(n,p) 35 S reaction by the irradiation of potassium chloride without any previous treatment and with previous heating under vacuum, were determined. The influence of irradiation time and temperature after irradiation was examined. Paper electrophoresis technique was employed for the determination of the chemical states. (Author) [pt

  13. Investigating the Effect of Chemical Management on Weeds Population, Agronomical Traits and Yield of Garlic (Allium sativum L. in Mazandaran Province

    Directory of Open Access Journals (Sweden)

    Sobhan Mahzari

    2018-02-01

    Full Text Available Introduction: Garlic (Allium sativum L. is an important winter crop in northern of Iran with a total of 9580 ha which produces approximately 90, 197 tons per year. It is the second most widely cultivated species of the genus, Allium after onion (Allium cepa. Also, Garlic along with onions and leeks are three major cultivated species in Alliaceae family. This plant because of high economic and medicinal values is cultivated in 2610 hectares of agricultural lands of Mazandaran Province, Iran. Slow growth rate, low height, and a thin canopy that does not cover the soil enough to sup-press weeds make garlic a poor competitor against the latter until the beginning of spring. According results, reported 71% yield losses in garlic crop if weeds are allowed to grow during the crop season. Weed interference is affected by the time of weed emergence relative to the crop’s phenological development. The weeds, which emerge early or simultaneously with the crop, are highly competitive and should be managed by farmers. Most weed management strategies in cereals target seedlings, as they are the most sensitive stage of the weed. However, emergence of weed seedlings varies every year in timing, extent and intensity. Therefore in this study, the effect of chemical management on reducing the density and biomass of weeds, yield and agronomic characteristics of garlic were studied in Mazandaran Province, Iran. Materials and Methods: After the selection of location test, in order to determine the physical and chemical properties before the preparation of soil for planting, sampling from the soil was carried out from the depth of 0 to 30 cm at some point. The farm was plowed using a moldboard plow, then the used fertilizers in this study were added to the soil twice before planting and then the fertilizers were incorporated with the soil using a Disc. The amount of used fertilizers in this study according to soil test were including: 200 kg Urea per hectare that

  14. Behavioral determinants of occupational exposure to chemical agents.

    Science.gov (United States)

    Meijman, T F; Ulenbelt, P; Lumens, M E; Herber, R F

    1996-01-01

    In the demand-control model (see T. Theorell & R. A. Karasek, 1996), it is hypothesized that workers in active jobs (high demands-high decision latitude) can exert effective coping strategies when confronted with environmental stessors. Thus, when exposed to similar levels of a chemical agent, lower concentrations of this agent in blood could be expected in these workers in comparison with workers in passive jobs. This theory was tested in 2 studies of lead-exposed workers: 18 male Caucasian workers from an electric accumulatory factory and 18 male Caucasian workers from a lead smelting factory. The results did not follow the hypothesized outcomes. In the work environment of the workers in active jobs, lower concentrations of lead in air were measured, but higher levels of lead in blood were observed in these workers. The opposite was true of workers in passive jobs. Differences in hygienic behavior at work may explain these unexpected results.

  15. Chemical Composition and Yield of Six Genotypes of Common Purslane (Portulaca oleracea L.): An Alternative Source of Omega-3 Fatty Acids.

    Science.gov (United States)

    Petropoulos, Spyridon Α; Karkanis, Anestis; Fernandes, Ângela; Barros, Lillian; Ferreira, Isabel C F R; Ntatsi, Georgia; Petrotos, Konstantinos; Lykas, Christos; Khah, Ebrahim

    2015-12-01

    Common purslane (Portulaca oleracea L.) is an annual weed rich in omega-3 fatty acids which is consumed for its edible leaves and stems. In the present study six different genotypes of common purslane (A-F) were evaluated for their nutritional value and chemical composition. Nutritional value and chemical composition depended on genotype. Oxalic acid content was the lowest for genotype D, whereas genotypes E and F are more promising for commercial cultivation, since they have low oxalic acid content. Genotype E had a very good antioxidant profile and a balanced composition of omega-3 and omega-6 fatty acids. Regarding yield, genotype A had the highest yield comparing to the other genotypes, whereas commercial varieties (E and F) did not differ from genotypes B and C. This study provides new information regarding common purslane bioactive compounds as affected by genotype and could be further implemented in food industry for products of high quality and increased added value.

  16. Qualitative determination of chemical and nutritional composition of ...

    African Journals Online (AJOL)

    The oil has very high saponification value and hence would be useful in soap industry. Some simple reducing sugars, including lactose, were identified. Key words: Parkia bioglobosa, Qalitative determination, Industrial use, Saponification, underexploited. African Journal of Biotechnology Vol. 4 (8), pp. 812-815 ...

  17. Effect of three pretreatment techniques on the chemical composition and on the methane yields of Opuntia ficus-indica (prickly pear) biomass.

    Science.gov (United States)

    Calabrò, P S; Catalán, E; Folino, A; Sánchez, A; Komilis, D

    2018-01-01

    Opuntia ficus-indica (OFI) is an emerging biomass that has the potential to be used as substrate in anaerobic digestion. The goal of this work was to investigate the effect of three pretreatment techniques (thermal, alkaline, acidic) on the chemical composition and the methane yield of OFI biomass. A composite experimental design with three factors and two to three levels was implemented, and regression modelling was employed using a total of 10 biochemical methane potential (BMP) tests. The measured methane yields ranged from 289 to 604 NmL/gVS added ; according to the results, only the acidic pretreatment (HCl) was found to significantly increase methane generation. However, as the experimental values were quite high with regards to the theoretical methane yield of the substrate, this effect still needs to be confirmed via further research. The alkaline pretreatment (NaOH) did not noticeably affect methane yields (an average reduction of 8% was recorded), despite the fact that it did significantly reduce the lignin content. Thermal pretreatment had no effect on the methane yields or the chemical composition. Scanning electron microscopy images revealed changes in the chemical structure after the addition of NaOH and HCl. Modelling of the cumulated methane production by the Gompertz modified equation was successful and aided in understanding kinetic advantages linked to some of the pretreatments. For example, the alkaline treatment (at the 20% dosage) at room temperature resulted to a μ max (maximum specific methane production rate [NmLCH 4 /(gVS added ·d)]) equal to 36.3 against 18.6 for the control.

  18. Chemical composition and methane yield of reed canary grass as influenced by harvesting time and harvest frequency

    DEFF Research Database (Denmark)

    Kandel, Tanka Prasad; Sutaryo, Sutaryo; Møller, Henrik Bjarne

    2013-01-01

    This study examined the influence of harvest time on biomass yield, dry matter partitioning, biochemical composition and biological methane potential of reed canary grass harvested twice a month in one-cut (OC) management. The regrowth of biomass harvested in summer was also harvested in autumn...... as a two-cut management with (TC-F) or without (TC-U) fertilization after summer harvest. The specific methane yields decreased significantly with crop maturity that ranged from 384 to 315 and from 412 to 283 NL (normal litre) (kg VS)-1 for leaf and stem, respectively. Approximately 45% more methane...... was produced by the TC-F management (5430 Nm3 ha-1) as by the OC management (3735 Nm3 ha-1). Specific methane yield was moderately correlated with the concentrations of fibre components in the biomass. Larger quantity of biogas produced at the beginning of the biogas assay from early harvested biomass...

  19. Effect of Irrigation Timing on Root Zone Soil Temperature, Root Growth and Grain Yield and Chemical Composition in Corn

    Directory of Open Access Journals (Sweden)

    Xuejun Dong

    2016-05-01

    Full Text Available High air temperatures during the crop growing season can reduce harvestable yields in major agronomic crops worldwide. Repeated and prolonged high night air temperature stress may compromise plant growth and yield. Crop varieties with improved heat tolerance traits as well as crop management strategies at the farm scale are thus needed for climate change mitigation. Crop yield is especially sensitive to night-time warming trends. Current studies are mostly directed to the elevated night-time air temperature and its impact on crop growth and yield, but less attention is given to the understanding of night-time soil temperature management. Delivering irrigation water through drip early evening may reduce soil temperature and thus improve plant growth. In addition, corn growers typically use high-stature varieties that inevitably incur excessive respiratory carbon loss from roots and transpiration water loss under high night temperature conditions. The main objective of this study was to see if root-zone soil temperature can be reduced through drip irrigation applied at night-time, vs. daytime, using three corn hybrids of different above-ground architecture in Uvalde, TX where day and night temperatures during corn growing season are above U.S. averages. The experiment was conducted in 2014. Our results suggested that delivering well-water at night-time through drip irrigation reduced root-zone soil temperature by 0.6 °C, increase root length five folds, plant height 2%, and marginally increased grain yield by 10%. However, irrigation timing did not significantly affect leaf chlorophyll level and kernel crude protein, phosphorous, fat and starch concentrations. Different from our hypothesis, the shorter, more compact corn hybrid did not exhibit a higher yield and growth as compared with taller hybrids. As adjusting irrigation timing would not incur an extra cost for farmers, the finding reported here had immediate practical implications for farm

  20. Amendment of Tephrosia Improved Fallows with Inorganic Fertilizers Improves Soil Chemical Properties, N Uptake, and Maize Yield in Malawi

    Directory of Open Access Journals (Sweden)

    Maggie G. Munthali

    2014-01-01

    Full Text Available Maize production in Malawi is limited mainly by low soil N and P. Improved fallows of N-fixing legumes such as Tephrosia and Sesbania offer options for improving soil fertility particularly N supply. The interactions of Tephrosia fallows and inorganic fertilizers on soil properties, N uptake, and maize yields were evaluated at Chitedze Research Station in Malawi. The results indicated that the level of organic matter and pH increased in all the treatments except for the control. Total N remained almost unchanged while available P decreased in all plots amended with T. vogelii but increased in T. candida plots where inorganic P was applied. Exchangeable K increased in all the plots irrespective of the type of amendment. The interaction of N and P fertilizers with T. vogelii fallows significantly increased the grain yield. The treatment that received 45 kg N ha−1 and 20 kg P ha−1 produced significantly higher grain yields (6.8 t ha−1 than all the other treatments except where 68 kg N ha−1 and 30 kg P ha−1 were applied which gave 6.5 t ha−1 of maize grain. T. candida fallows alone or in combination with N and P fertilizers did not significantly affect grain yield. However, T. candida fallows alone can raise maize grain yield by 300% over the no-input control. Based on these results we conclude that high quality residues such as T. candida and T. vogelii can be used as sources of nutrients to improve crop yields and soil fertility in N-limited soils. However, inorganic P fertilizer is needed due to the low soil available P levels.

  1. MULTICOMPONENT DETERMINATION OF CHLORINATED HYDROCARBONS USING A REACTION-BASED CHEMICAL SENSOR .2. CHEMICAL SPECIATION USING MULTIVARIATE CURVE RESOLUTION

    NARCIS (Netherlands)

    Tauler, R.; Smilde, A. K.; HENSHAW, J. M.; BURGESS, L. W.; KOWALSKI, B. R.

    1994-01-01

    A new multivariate curve resolution method that can extract analytical information from UV/visible spectroscopic data collected from a reaction-based chemical sensor is proposed. The method is demonstrated with the determination of mixtures of chlorinated hydrocarbons by estimating the kinetic and

  2. Determination of contact maps in proteins: A combination of structural and chemical approaches

    Energy Technology Data Exchange (ETDEWEB)

    Wołek, Karol; Cieplak, Marek, E-mail: mc@ifpan.edu.pl [Institute of Physics, Polish Academy of Science, Al. Lotników 32/46, 02-668 Warsaw (Poland); Gómez-Sicilia, Àngel [Instituto Cajal, Consejo Superior de Investigaciones Cientificas (CSIC), Av. Doctor Arce, 37, 28002 Madrid (Spain); Instituto Madrileño de Estudios Avanzados en Nanociencia (IMDEA-Nanociencia), C/Faraday 9, 28049 Cantoblanco (Madrid) (Spain)

    2015-12-28

    Contact map selection is a crucial step in structure-based molecular dynamics modelling of proteins. The map can be determined in many different ways. We focus on the methods in which residues are represented as clusters of effective spheres. One contact map, denoted as overlap (OV), is based on the overlap of such spheres. Another contact map, named Contacts of Structural Units (CSU), involves the geometry in a different way and, in addition, brings chemical considerations into account. We develop a variant of the CSU approach in which we also incorporate Coulombic effects such as formation of the ionic bridges and destabilization of possible links through repulsion. In this way, the most essential and well defined contacts are identified. The resulting residue-residue contact map, dubbed repulsive CSU (rCSU), is more sound in its physico-chemical justification than CSU. It also provides a clear prescription for validity of an inter-residual contact: the number of attractive atomic contacts should be larger than the number of repulsive ones — a feature that is not present in CSU. However, both of these maps do not correlate well with the experimental data on protein stretching. Thus, we propose to use rCSU together with the OV map. We find that the combined map, denoted as OV+rCSU, performs better than OV. In most situations, OV and OV+rCSU yield comparable folding properties but for some proteins rCSU provides contacts which improve folding in a substantial way. We discuss the likely residue-specificity of the rCSU contacts. Finally, we make comparisons to the recently proposed shadow contact map, which is derived from different principles.

  3. Understanding N timing in corn yield and fertilizer N recovery: An insight from an isotopic labeled-N determination

    Science.gov (United States)

    de Almeida, Rodrigo Estevam Munhoz; Pierozan Junior, Clovis; Lago, Bruno Cocco; Trivelin, Paulo Cesar Ocheuze

    2018-01-01

    Early fertilizer nitrogen (N) application on cover crops or their residues during the off-season is a practice adopted in Brazil subtropical conditions under no-tillage corn (Zea mays L.) systems. However, the effect of early N application on yield, plant N content, and N recovery efficiency (NRE) for corn is not yet well documented. Five fertilizer N timings in an oat-corn system were evaluated in two studies utilizing an isotopic-labeled N determination, 15N isotope. The N fertilization timings were: (i) oat tillering, (ii) 15 days before corn planting time, over the oat residues, (iii) at corn planting time, (iv) in-season at the three-leaf growth stage (V3), and (v) in-season split application at V3 and six-leaf (V6) growth stages. Based on the statistical analysis, the N fertilization timings were separated into three groups: 1) N-OATS, designated to N applied at oat; 2) N-PLANT, referred to pre-plant and planting N applications; and 3) N-CORN, designated to in-season corn N applications. Corn yield was not affected by the N fertilization timing. However, the N-CORN N fertilization timings enhanced NRE by 17% and 35% and final N recovery system (plant plus soil) by 16% and 24% all relative to N-OATS and N-PLANT groups, respectively. Overall, N-OATS resulted in the largest N derived from fertilizer (NDFF) amount in the deeper soil layer, in overall a delta of 10 kg N ha-1 relative to the rest of the groups. Notwithstanding corn yield was not affected, early N fertilization under subtropical conditions is not a viable option since NRE was diminished and the non-recovery N increased relative to the in-season N applications. PMID:29462178

  4. Understanding N timing in corn yield and fertilizer N recovery: An insight from an isotopic labeled-N determination.

    Science.gov (United States)

    Maciel de Oliveira, Silas; Almeida, Rodrigo Estevam Munhoz de; Ciampitti, Ignacio A; Pierozan Junior, Clovis; Lago, Bruno Cocco; Trivelin, Paulo Cesar Ocheuze; Favarin, José Laércio

    2018-01-01

    Early fertilizer nitrogen (N) application on cover crops or their residues during the off-season is a practice adopted in Brazil subtropical conditions under no-tillage corn (Zea mays L.) systems. However, the effect of early N application on yield, plant N content, and N recovery efficiency (NRE) for corn is not yet well documented. Five fertilizer N timings in an oat-corn system were evaluated in two studies utilizing an isotopic-labeled N determination, 15N isotope. The N fertilization timings were: (i) oat tillering, (ii) 15 days before corn planting time, over the oat residues, (iii) at corn planting time, (iv) in-season at the three-leaf growth stage (V3), and (v) in-season split application at V3 and six-leaf (V6) growth stages. Based on the statistical analysis, the N fertilization timings were separated into three groups: 1) N-OATS, designated to N applied at oat; 2) N-PLANT, referred to pre-plant and planting N applications; and 3) N-CORN, designated to in-season corn N applications. Corn yield was not affected by the N fertilization timing. However, the N-CORN N fertilization timings enhanced NRE by 17% and 35% and final N recovery system (plant plus soil) by 16% and 24% all relative to N-OATS and N-PLANT groups, respectively. Overall, N-OATS resulted in the largest N derived from fertilizer (NDFF) amount in the deeper soil layer, in overall a delta of 10 kg N ha-1 relative to the rest of the groups. Notwithstanding corn yield was not affected, early N fertilization under subtropical conditions is not a viable option since NRE was diminished and the non-recovery N increased relative to the in-season N applications.

  5. Determination of road dust loadings and chemical characteristics using resuspension.

    Science.gov (United States)

    Chen, Jianhua; Wang, Wei; Liu, Hongjie; Ren, Lihong

    2012-03-01

    The contribution of fugitive dust from traffic to air pollution can no longer be ignored in China. In order to obtain the road dust loadings and to understand the chemical characteristics of PM(10) and PM(2.5) from typical road dust, different paved roads in eight districts of Beijing were selected for dust collection during the four seasons of 2005. Ninety-eight samples from 28 roads were obtained. The samples were resuspended using equipment assembled to simulate the rising process of road dust caused by the wind or wheels in order to obtain the PM(10) and PM(2.5) filter samples. The average road dust loading was 3.82 g m(-2), with the highest of 24.22 g m(-2) being in Hutongs in the rural-urban continuum during winter. The road dust loadings on higher-grade roads were lower than those on lower-grade roads. Attention should be paid to the pollution in the rural-urban continuum areas. The sums of element abundances measured were 16.17% and 18.50% for PM(10) and PM(2.5) in road dust. The average abundances of OC and EC in PM(10) and PM(2.5) in road dust were 11.52%, 2.01% and 12.50%, 2.06%, respectively. The abundance of elements, water-soluble ions, and OC, EC in PM(10) and PM(2.5) resuspended from road dust did not change greatly with seasons and road types. The soil dust, construction dust, dust emitted from burning coal, vehicle exhaust, and deposition of particles in the air were the main sources of road dust in Beijing. Affected by the application of snow-melting agents in Beijing during winter, the amount of Cl( - ) and Na( + ) was much higher during that time than in the other seasons. This will have a certain influence on roads, bridges, vegetations, and groundwater.

  6. The use of yield tracers for the determination of aplha-emitting actinides in the marine environment

    International Nuclear Information System (INIS)

    Harvey, B.R.; Lovett, M.B.

    1984-01-01

    The need for yield tracers and their general analytical application is briefly discussed and more fully expanded in the context of the radiochemical determination of alpha-emitting actinides. The important alpha-emitting nuclides of the actinide elements found in the marine environment are listed. The environmental significance and analytical implications arising from the multiplicity of valency states found amongst the earlier members of the actinide series are noted. The tracers that are available for analyses and their selection and suitability for particular applications are discussed and the general precautions that need to be observed in their use are given. Use of the dual tracer technique in the study of speciation of the actinides in the marine environment is discussed with special reference to plutonium in sea water. The limited applicability of plutonium as a yield tracer in the study of neptunium speciation is noted and the latest developments in the investigation of 235 Np as an alternative tracer for neptunium are given. The possibility of the joint use of americium and curium nuclides as tracers in the study of the speciation of these two elements is explored. (orig.)

  7. Regulatory role of OsMADS34 in the determination of glumes fate, grain yield and quality in rice

    Directory of Open Access Journals (Sweden)

    Deyong Ren

    2016-12-01

    Full Text Available Grasses produce seeds on spikelets, a unique type of inflorescence. Despite the importance of grass crops for food, the genetic mechanisms that control spikelet development remain poorly understood. In this study, we used m34-z, a new mutant allele of the rice (Oryza sativa E-class gene OsMADS34, to examine OsMADS34 function in determining the identities of glumes (rudimentary glume and sterile lemma and grain size. In the m34-z mutant, both the rudimentary glume and sterile lemma were homeotically converted to the lemma-like organs and acquired the lemma identity, suggesting that OsMADS34 plays important roles in the development of glumes. In the m34-z mutant, most of the grains from the secondary panicle branches were decreased in size, compared with grains from wild type, but no differences were observed in the grains from the primary panicle branches. The amylose content and gel consistency, and a seed-setting rate from the secondary panicle branches were reduced in the m34-z mutant. Interesting, transcriptional activity analysis revealed that OsMADS34 protein was a transcription repressor and it may influence grain yield by suppressing the expressions of BG1, GW8, GW2 and GL7 in the m34-z mutant. These findings revealed that OsMADS34 largely affects grain yield by affecting the size of grains from the secondary branches.

  8. Recent Microextraction Techniques for Determination and Chemical Speciation of Selenium

    Directory of Open Access Journals (Sweden)

    Ibrahim Ahmed S. A.

    2017-05-01

    Full Text Available Research designed to improve extraction has led to the development of microextraction techniques (ME, which involve simple, low cost, and effective preconcentrationof analytes in various matrices. This review is concerned with the principles and theoretical background of ME, as well as the development of applications for selenium analysis during the period from 2008 to 2016. Among all ME, dispersive liquid-liquid microextraction was found to be most favorable for selenium. On the other hand, atomic absorption spectrometry was the most frequently used instrumentation. Selenium ME have rarely been coupled to spectrophotometry and X-ray spectrophotometry methods, and there is no published application of ME with electrochemical techniques. We strongly support the idea of using a double preconcentration process, which consists of microextraction prior to preconcentration, followed by selenium determination using cathodic stripping voltammetry (ME-CSV. More attention should focus on the development of accurate, precise, and green methods for selenium analysis.

  9. Description of Some Ecological Factors in Three Forest Sites in Lorestan Province and Their Impact on Myrtle (Myrtus communis L. Essential Oil Yield and Chemical Components

    Directory of Open Access Journals (Sweden)

    Z. Mir-Azadi

    2013-03-01

    Full Text Available Due to the side effects of chemical drugs, special attention is given recently to pharmaceutical plants. Myrtle (Myrtus communis L. is one of the valuable pharmaceutical plants, which is distributed over the vast areas of Iran. Yield and components of essential oil of this plant is dependent on ecological and genetic factors. In order to describe some ecological factors that affect myrtle in Lorestan province, three forest sites (Sepiddasht, Chame-moord, and Hamzeh Camp were selected. Some effective ecological factors on type of essential oil were measured and compared among the sites. To compare the yield and components of essential oil, myrtle leaves were collected during flowering stage in each site. Leaves were dried in open air conditions and the oil was extracted by distillation. Yield of essential oil was calculated and its components were identified by GC and GC/MS. Results showed that maximum yield belongs to Sepiddasht site. The altitude and soil Na, P, and organic carbon content of this site is quite different from other two sites. The main components of essential oils of these three sites had considerable differences. The amount of 9,10 anthracenedione was 29.1% in Sepiddasht site, while it was not found in the oil of Chame-moord site. It seems that differences in ecological and soil properties of the tree sites could have major effect on essential oil yield and its composition.

  10. Determination of NABE in urine of high-yield dairy cows in early lactation in conditions of moderate heat stress

    Directory of Open Access Journals (Sweden)

    Fratrić Natalija

    2010-01-01

    Full Text Available The work presents the results of investigations of the effect of moderate heat stress on the acidobasal status in high-yield dairy cows in early lactation. Improving performance in high-yield dairy cows increases their inclination toward metabolic disorders. The most likely to be affected is the acid-base balance, in particular when cows are exposed to heat stress. Investigations so far have shown that the taking of urine samples and their analysis is the best and fastest way to diagnose disorders in the acid-base balance. Investigations were carried out on 7 clinically healthy cows of the Holstein- Friesian breed in the phase of early lactation, 30 to 40 days (on days 30, 33 and 40 following calving during the summer period, during the month of July, when there were significant variations in daily and nightly temperatures. The cows were in the second and fourth lactation, the annual milk yield was 8000 L milk per cow. The average daily milk production in the early phase of lactation ranged from 35 to 40 L. The cows were fed mixed rations (TMR twice daily. Lucerne hay in limited quantities was given to the cows prior to the mixed feed ration. The ration for this animal category was optimized on the grounds of the daily milk production. The balance of cations and anions in the feed ration stood at 95 mEq/kg DM. The results clearly demonstrate the cows' response to moderate heat stress through the defense parameters in urine (urine pH, NABE (net-acid-base-excretion, acids, bases, ammonium ion (NH4. The determination of the kidney NABE yields more correct data than the urine pH on acidotic conditions. The results of examinations of the urine pH do not show any digressions from physiological values and are approximately the same in all cows during the investigated periods. Normal NABE values are from 100-200 mmol/L. Burdening with acid products results in a NABE range from 0-100mmol/L, and metabolic acidosis results in NAB<0 mmol/L. NABE in the cows

  11. Determination of the shape factor of {sup 90}Sr by means of the cutoff energy yield method

    Energy Technology Data Exchange (ETDEWEB)

    Grau Carles, A. [Instituto de Matematicas y Fisica Fundamental (CSIC), Dcho. 211, C/Serrano 113b, 28006 Madrid (Spain)], E-mail: agrau@imaff.cfmac.csic.es; Kossert, K. [Physikalisch-Technische Bundesanstalt, Department 6.1, Bundesallee 100, D-38116 Braunschweig (Germany); Grau Malonda, A. [CIEMAT, Departamento de Proyectos Estrategicos, Avda. Complutense 22, 28040 Madrid (Spain)

    2008-06-15

    Usually, Kurie plots are used to analyze beta-spectra shape-factor functions measured by means of semiconductor and magnetic spectrometers. A drawback of these techniques is the occurrence of self-absorption within the samples through which the emission spectrum is altered. In liquid-scintillation samples self-absorption does not occur, but the poor energy resolution makes the analysis of the spectra difficult. To overcome this problem, two resolution-invariant observables are used for determining the shape-factor function of {sup 90}Sr: (1) the maximum point energy and (2) the cutoff energy yield. The measured shape-factor function of {sup 90}Sr agrees with the one which is predicted by theory for the first-forbidden unique transition.

  12. The effect of organic, biological and chemical fertilizers on yield, essential oil percentage and some agroecological characteristics of summer savory (Satureja hortensis L. under Mashhad conditions

    Directory of Open Access Journals (Sweden)

    E Gholami Sharafkhane

    2016-05-01

    , all studied characteristics including plant height, lateral branches, flowering shoot yield, stem yield, percentage of essential oil and dry matter yield were affected positively by cattle manure. The highest plant height and number of lateral branches resulted from vermicompost and combination of Nitroxin+Biophosphor+Biosulfur, respectively. Biosulfur fertilizer produced the highest dry matter yield, flowering shoot yield and stem yield. Percentage of essential oil was also significantly affected by fertilizer treatments as the most percentage of essential oil was obtained from Nitroxin, vermicompost and combination of Nitroxin+Biophosphor+Biosulfur. A positive and strong correlation was observed between dry mater yield and flowering shoot yield and stem yield, respectively. Conclusion The results indicated that application of organic and inoculation of biological fertilizers have positive effects on improvement of qualitative and quantitative traits of summer savory, so it could be considered as an alternative method for healthy production of summer savory. Acknowledgements The expenses for this research were funded by the Research and Technology Deputy of the Ferdowsi University of Mashhad, Faculty of agriculture. The financial support is appreciated. References Chen, J. 2006. The combined use of chemical and organic fertilizers and/or biofertilizer for crop growth and soil fertility. International Workshop on Sustained Management of the Soil-Rhizosphere System for Efficient Crop Production and Fertilizer Use. October 16-20. Thailand. 11 pp. Gliessman, S.R. 1998. Agroecology: Ecological Processes in Sustainable Agriculture. CRC Press. ISBN: 1-57504-043-3 Mahfouz, S.A., Sharaf- Eldin, A. 2007. Effect of mineral vs. biofertilizer on growth, yield, and essential oil content of fennel (Foeniculum vulgare Mill.. Agrophysics Journal 21: 361-366. Omidbeigi, R. 2000. Approaches to Production and Processing of Medicinal plants, vol. (3. Beh Nashr Publisher, Mashhad. (In

  13. Effect of Organic and Chemical Fertilizers on Yield and Essential Oil of Two Ecotypes of Savory (Satureja hortensis L. under Normal and Drought Stress Conditions

    Directory of Open Access Journals (Sweden)

    O Akrami nejad

    2016-02-01

    height, grain and biological yield, chlorophyll index, ionic leakage, relative water content, number of branches, essence percentage and essence amount were evaluated. Data were analyzed with SAS and MSTAT-C software and mean comparison was done using Duncan test at %5 level. Results and Discussion The results showed that drought stress reduced plant height, number of branches, oil yield, relative water content, SPAD index and increased ion leakage. Meanwhile, it had no significant effect on the percent of oil. Fertilizers increased plant height, number of branches, yield, chlorophyll index and oil yield, while it decreased ion leakage in contrast with control. Baher et al (2002 have reported that drought stress reduced plant height, grain yield, and branches number of Savory. As nutrients deficit is one of the main factors in control of plant height and yield, plant that were treated with control had the lowest growth. Organic fertilizers provide appropriate plant growth via gradual release of nutrients during growth season and saving water. Two ecotypes had significant differences for yield, number of branches and ionic leakage. Kerman ecotype showed better yield performance. The results showed that water stress reduced yield, number of branches and plant height of savory. Meanwhile fertilizers (especially cow and hen manure could reduce the effects of drought. Conclusions Generally, organic fertilizers, especially cow manure, produced higher yield and showed a better response to drought stress. It might be for higher moisture maintenance in contrast with chemical fertilizers. It seems that, using cow manure could be helpful to overcome the negative effects of drought stress.

  14. Protein energetic conformational analysis from NMR chemical shifts (PECAN) and its use in determining secondary structural elements

    Energy Technology Data Exchange (ETDEWEB)

    Eghbalnia, Hamid R.; Wang Liya; Bahrami, Arash [National Magnetic Resonance Facility at Madison, Biochemistry Department (United States); Assadi, Amir [University of Wisconsin-Madison, Mathematics Department (United States); Markley, John L. [National Magnetic Resonance Facility at Madison, Biochemistry Department (United States)], E-mail: eghbalni@nmrfam.wisc.edu

    2005-05-15

    We present an energy model that combines information from the amino acid sequence of a protein and available NMR chemical shifts for the purposes of identifying low energy conformations and determining elements of secondary structure. The model ('PECAN', Protein Energetic Conformational Analysis from NMR chemical shifts) optimizes a combination of sequence information and residue-specific statistical energy function to yield energetic descriptions most favorable to predicting secondary structure. Compared to prior methods for secondary structure determination, PECAN provides increased accuracy and range, particularly in regions of extended structure. Moreover, PECAN uses the energetics to identify residues located at the boundaries between regions of predicted secondary structure that may not fit the stringent secondary structure class definitions. The energy model offers insights into the local energetic patterns that underlie conformational preferences. For example, it shows that the information content for defining secondary structure is localized about a residue and reaches a maximum when two residues on either side are considered. The current release of the PECAN software determines the well-defined regions of secondary structure in novel proteins with assigned chemical shifts with an overall accuracy of 90%, which is close to the practical limit of achievable accuracy in classifying the states.

  15. Protein energetic conformational analysis from NMR chemical shifts (PECAN) and its use in determining secondary structural elements

    International Nuclear Information System (INIS)

    Eghbalnia, Hamid R.; Wang Liya; Bahrami, Arash; Assadi, Amir; Markley, John L.

    2005-01-01

    We present an energy model that combines information from the amino acid sequence of a protein and available NMR chemical shifts for the purposes of identifying low energy conformations and determining elements of secondary structure. The model ('PECAN', Protein Energetic Conformational Analysis from NMR chemical shifts) optimizes a combination of sequence information and residue-specific statistical energy function to yield energetic descriptions most favorable to predicting secondary structure. Compared to prior methods for secondary structure determination, PECAN provides increased accuracy and range, particularly in regions of extended structure. Moreover, PECAN uses the energetics to identify residues located at the boundaries between regions of predicted secondary structure that may not fit the stringent secondary structure class definitions. The energy model offers insights into the local energetic patterns that underlie conformational preferences. For example, it shows that the information content for defining secondary structure is localized about a residue and reaches a maximum when two residues on either side are considered. The current release of the PECAN software determines the well-defined regions of secondary structure in novel proteins with assigned chemical shifts with an overall accuracy of 90%, which is close to the practical limit of achievable accuracy in classifying the states

  16. Computational chemical imaging for cardiovascular pathology: chemical microscopic imaging accurately determines cardiac transplant rejection.

    Directory of Open Access Journals (Sweden)

    Saumya Tiwari

    Full Text Available Rejection is a common problem after cardiac transplants leading to significant number of adverse events and deaths, particularly in the first year of transplantation. The gold standard to identify rejection is endomyocardial biopsy. This technique is complex, cumbersome and requires a lot of expertise in the correct interpretation of stained biopsy sections. Traditional histopathology cannot be used actively or quickly during cardiac interventions or surgery. Our objective was to develop a stain-less approach using an emerging technology, Fourier transform infrared (FT-IR spectroscopic imaging to identify different components of cardiac tissue by their chemical and molecular basis aided by computer recognition, rather than by visual examination using optical microscopy. We studied this technique in assessment of cardiac transplant rejection to evaluate efficacy in an example of complex cardiovascular pathology. We recorded data from human cardiac transplant patients' biopsies, used a Bayesian classification protocol and developed a visualization scheme to observe chemical differences without the need of stains or human supervision. Using receiver operating characteristic curves, we observed probabilities of detection greater than 95% for four out of five histological classes at 10% probability of false alarm at the cellular level while correctly identifying samples with the hallmarks of the immune response in all cases. The efficacy of manual examination can be significantly increased by observing the inherent biochemical changes in tissues, which enables us to achieve greater diagnostic confidence in an automated, label-free manner. We developed a computational pathology system that gives high contrast images and seems superior to traditional staining procedures. This study is a prelude to the development of real time in situ imaging systems, which can assist interventionists and surgeons actively during procedures.

  17. Chemical composition and methane yield of reed canary grass as influenced by harvesting time and harvest frequency.

    Science.gov (United States)

    Kandel, Tanka P; Sutaryo, Sutaryo; Møller, Henrik B; Jørgensen, Uffe; Lærke, Poul E

    2013-02-01

    This study examined the influence of harvest time on biomass yield, dry matter partitioning, biochemical composition and biological methane potential of reed canary grass harvested twice a month in one-cut (OC) management. The regrowth of biomass harvested in summer was also harvested in autumn as a two-cut management with (TC-F) or without (TC-U) fertilization after summer harvest. The specific methane yields decreased significantly with crop maturity that ranged from 384 to 315 and from 412 to 283 NL (normal litre) (kgVS)(-1) for leaf and stem, respectively. Approximately 45% more methane was produced by the TC-F management (5430Nm(3)ha(-1)) as by the OC management (3735Nm(3)ha(-1)). Specific methane yield was moderately correlated with the concentrations of fibre components in the biomass. Larger quantity of biogas produced at the beginning of the biogas assay from early harvested biomass was to some extent off-set by lower concentration of methane. Copyright © 2012 Elsevier Ltd. All rights reserved.

  18. Chemical separation and ICP-AES determination of rare earths in Al2O3 matrix

    International Nuclear Information System (INIS)

    Argekar, A.A.; Kulkarni, M.J.; Page, A.G.; Manchanda, V.K.

    2005-01-01

    A chemical separation-ICP-AES method has been developed for determination of rare earths in alumina matrix. The quantitative separation of rare earths has also been confirmed using radiotracers. (author)

  19. Optimal cofactor swapping can increase the theoretical yield for chemical production in Escherichia coli and Saccharomyces cerevisiae

    DEFF Research Database (Denmark)

    King, Zachary A.; Feist, Adam

    2014-01-01

    Maintaining cofactor balance is a critical function in microorganisms, but often the native cofactor balance does not match the needs of an engineered metabolic flux state. Here, an optimization procedure is utilized to identify optimal cofactor-specificity "swaps" for oxidoreductase enzymes...... specificity of central metabolic enzymes (especially GAPD and ALCD2x) is shown to increase NADPH production and increase theoretical yields for native products in E. coli and yeast-including l-aspartate, l-lysine, l-isoleucine, l-proline, l-serine, and putrescine-and non-native products in E. coli-including 1...

  20. Development of a Chemically Defined Medium for Better Yield and Purification of Enterocin Y31 from Enterococcus faecium Y31

    OpenAIRE

    Liu, Wenli; Zhang, Lanwei; Yi, Huaxi

    2017-01-01

    The macro- and micronutrients in traditional medium, such as MRS, used for cultivating lactic acid bacteria, especially for bacteriocin production, have not been defined, preventing the quantitative monitoring of metabolic flux during bacteriocin biosynthesis. To enhance Enterocin Y31 production and simplify steps of separation and purification, we developed a simplified chemically defined medium (SDM) for the growth of Enterococcus faecium Y31 and production of its bacteriocin, Enterocin Y31...

  1. Determination of radiochemical yield of 99mTc radiopharmaceutical preparations using gamma counter and linear radiochromatography scanner

    International Nuclear Information System (INIS)

    Martins, Patricia de A.; Moura, Rebeca G.; Shiki, Andressa M.; Fukumori, Neuza T.O.; Matsuda, Margareth M.N.

    2013-01-01

    The radiochemical purity (RCP) evaluation is a prerequisite for radiopharmaceuticals before the administration in patients. RCP is defined as the proportion of the total radioactivity in the product that is present in the specified chemical form. The most widely used techniques for RCP determination in radiopharmaceutical preparations are thin layer chromatography (TLC-Al), instant thin layer chromatography (ITLC-SG) and paper chromatography (PC). These techniques combined with radioactivity detection are one of the most important tools in the RCP of the radiopharmaceutical compounds. Several methods are used for the determination of the spatial distribution of radioactivity on the strips. The aim of this study was to compare two methods for radioactivity measurement in the determination of RCP in 99m Tc radiopharmaceuticals using gamma counter and linear radiochromatography scanner. Lyophilized radiopharmaceuticals were labeled with 99m Tc. The analysis was carried out using TLC-Al and high performance thin layer chromatography (HPTLC-Cellulose) sheets, ITLC-SG and 3MM Whatman PC. The radioactivity distribution was determined by counting each strip during 1 minute in a radiochromatography TLC scanner. For comparison, the strips were cut into small pieces and each one was separately measured in a gamma-counter during 0.20 minutes in 70-210 KeV 99m Tc window. USP 36 and FDA specify that not less than 90% of the total radioactivity must be in the spot corresponding to 99m Tc labeled compound. In conclusion, the procedure for RCP determination of ALBUMINA-TEC, DEX500-TEC, ECD-TEC, MACRO-TEC and MIBI-TEC can be faster using radiochromatography. (author)

  2. Determination of radiochemical yield of {sup 99m}Tc radiopharmaceutical preparations using gamma counter and linear radiochromatography scanner

    Energy Technology Data Exchange (ETDEWEB)

    Martins, Patricia de A.; Moura, Rebeca G.; Shiki, Andressa M.; Fukumori, Neuza T.O.; Matsuda, Margareth M.N., E-mail: patyosborne@yahoo.com [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2013-07-01

    The radiochemical purity (RCP) evaluation is a prerequisite for radiopharmaceuticals before the administration in patients. RCP is defined as the proportion of the total radioactivity in the product that is present in the specified chemical form. The most widely used techniques for RCP determination in radiopharmaceutical preparations are thin layer chromatography (TLC-Al), instant thin layer chromatography (ITLC-SG) and paper chromatography (PC). These techniques combined with radioactivity detection are one of the most important tools in the RCP of the radiopharmaceutical compounds. Several methods are used for the determination of the spatial distribution of radioactivity on the strips. The aim of this study was to compare two methods for radioactivity measurement in the determination of RCP in {sup 99m}Tc radiopharmaceuticals using gamma counter and linear radiochromatography scanner. Lyophilized radiopharmaceuticals were labeled with {sup 99m}Tc. The analysis was carried out using TLC-Al and high performance thin layer chromatography (HPTLC-Cellulose) sheets, ITLC-SG and 3MM Whatman PC. The radioactivity distribution was determined by counting each strip during 1 minute in a radiochromatography TLC scanner. For comparison, the strips were cut into small pieces and each one was separately measured in a gamma-counter during 0.20 minutes in 70-210 KeV {sup 99m}Tc window. USP 36 and FDA specify that not less than 90% of the total radioactivity must be in the spot corresponding to {sup 99m}Tc labeled compound. In conclusion, the procedure for RCP determination of ALBUMINA-TEC, DEX500-TEC, ECD-TEC, MACRO-TEC and MIBI-TEC can be faster using radiochromatography. (author)

  3. Effect of Different Levels of Organic and Chemical Fertilizers on Yield, Harvest Index and Extract Percentage of Hemp (Cannabis sativa L.

    Directory of Open Access Journals (Sweden)

    S Laleh

    2018-02-01

    Full Text Available Introduction Hemp is a dioecious and annual plant. The most important use to this plant is in the food, drug, and natural fibers. Proper fertilizer management for a medicinal plant species is important for increasing its yield and maintaining the quality of active principles. Sustainable farming is on the basis of natural fertilizer application with the aim of decreasing chemical fertilizers. Various studies show that application of animal manure with chemical fertilizers (as N, P and … have positive effects on soil structure, microbial population, soil fertility, growth and yield of plant with the aim of protecting the environment. Therefore, the present study was under taken to evaluate the effect of organic amendments enriched with chemical fertilizers of nitrogen and phosphorus on yield and extract of hemp. Materials and Methods To study the effect of different levels of animal manure and chemical fertilizers, a split factorial experiment, based on complete randomized blocks design with three replications was conducted at the research Farm of Faculty of agriculture, University of Birjand, during the growing season 2014-2015. Experimental factors were animal manure (0, 10, 20 and 30 t. ha-1well rotted farmyard manure as the main plot, and factorial application of three levels of N (0, 50 and 100 kg N ha-1 as Urea with two levels of P (0 and 80 kg P2O5 ha-1 as triple and P was superphosphate as sub-plot. Animal manure, P and half of the N fertilizer were applied before planting and the other half of N were applied by top dressing. Hemp were planted 5 may on rows 60 cm apart, with 30 cm distance between each hemp on row, at the depth of 3-4 cm. Measured traits included leaf, stem and seed weights, stem height and diameter, 1000 seed weight, and leaves extract percentage per square meter in sub-plot for female plants of hemp. Also percentage of female plants calculated per sub-plot. Finally, all variables were analyzed by SAS software (V. 9

  4. INFLUENCE OF VERMICOMPOST ON THE PHYSICO-CHEMICAL AND BIOLOGICAL PROPERTIES IN DIFFERENT TYPES OF SOIL ALONG WITH YIELD AND QUALITY OF THE PULSE CROP-BLACKGRAM

    Directory of Open Access Journals (Sweden)

    K. Parthasarathi, M. Balamurugan, L. S. Ranganathan

    2008-01-01

    Full Text Available Field experiments were conducted during 2002-2003 on clay loam, sandy loam and red loam soil at Sivapuri, Chidambaram, Tamil Nadu, to evaluate the efficacy of vermicompost on the physico-chemical and biological characteristics of the soils and on the yield and nutrient content of blackgram - Vigna mungo, in comparison to inorganic fertilizers nitrogen, phosphorous, potassium. Vermicompost had increased the pore space, reduced particle and bulk density, increased water holding capacity, cation exchange capacity, reduced pH and electrical conductivity, increased organic carbon content, available nitrogen, phosphorous, potassium and microbial population and activity in all the soil types, particularly clay loam. The yield and quality (protein and sugar content in seed of blackgram was enhanced in soils, particularly clay loam soil. On the contrary, the application of inorganic fertilizers has resulted in reduced porosity, compaction of soil, reduced carbon and reduced microbial activity.

  5. Changes in growth and yield attributes of two selected maize varieties as influenced by application of chemical (npk) and organic (bat's manure) fertilizers in pala (chad) grown field

    International Nuclear Information System (INIS)

    Ridine, W.; Ngakou, A.; Mbaiguinam, M.; Namba, F.; Anna, P

    2014-01-01

    The present experiment was conducted in Pala, region of the Mayo-Kebi West division, in a contribution to improve maize production in Chad. The work was oriented towards the evaluation of the interactions between chemical (NPK) and organic (bat's manure) fertilizers on growth and yield attributes of TZEE-W and IB selected maize varieties. The experimental design was a (5x2)x4 factorial design in which the main factor was the proportion of organic/chemical fertilizer (%), and the maize variety as the secondary factor, comprising the following six treatments repeated four times: control (T0) with 0 % NPK and 0 % bat's manure; T1 with 100% NPK; T2 with 100% bat's manure; T3 with 75% NPK and 25% bat's manure; T4 with 75% bat's manure and 25% NPK; T5 with 50% bat's manure and 50% NPK. Results show a variation in experimental soils pH of treatments from 5.91 to 7.92, depending on the proportion of the fertilizers applied. There were significant yield differences among treatments, as well as maize varieties. The 50% NPK+50% bat's manure was found as the best treatment to significantly (p<0.0001) enhance the yield of IB (51.2 t/ha) and TZEE-W (37.9 t/ha) maize varieties compared to their respective controls (7.25 t/ha and 6.76 t/ha). These results suggest that the combination at equal proportion of NPK and bat's manure could be recommended to sustainably improve maize production in Pala-Chad, thus with a considerable alleviation of the pollution risks that have been attributed to chemical fertilizer. (author)

  6. Determination of 114Pd cumulative yield and investigation of the fine-structure at light peak in mass distribution of 252Cf spontaneous fission

    International Nuclear Information System (INIS)

    Yu Runlan; Li Xueliang; Cui Anzhi; Guo Jingru; Yan Shuhen; Tang Peijia; Liu Daming

    1991-07-01

    A rapid radiochemical procedure for Pd separation was developed. It was the first time to use radiochemical techniques to determine 114 Pd cumulative yield (2.50 ± 0.14)% in 252 Cf spontaneous fission. The cumulative yields of (3.50 ± 0.13)% and (3.70 ± 0.11)% for 112 Pd and 113g Ag were also obtained. These are in agreement with Skovorodkin's results. The cumulative yields determined show that there is a fine-structure at light peak of mass number A = 113 in the mass distribution of 252 Cf spontaneous fission

  7. Lime and rates and sources of phosphorus as influencing soybean yield and chemical properties of Pelotas soil (alfisol)

    International Nuclear Information System (INIS)

    Machado, M.O.

    1983-01-01

    The effect of five phosphates as sources of phosphorus for soybean (Bragg cultivar) was evaluated in two rates (100 and 200 Kg/ha of total P 2 O 5 ), on limed and unlimed soil condtions. The experiment was carried out under field conditions, during the soybean growing season of 1973/74, 1974/75, 1975/76 and 1976/77, at UEPAE Pelotas station. The pH and the exchangeable Ca + Mg content from the soil were increased with Gafsa phosphate, but mainly with lime, Thomas slag and Yoorin thermophosphate application. The exchangeable Al content was eliminated by lime application and decreased annually by application of Gafsa phosphate, Thomas slag and Yoorin thermophosphate, when the lime was not applied. Thomas slag and Yoorin thermophosphate were the best phosphates for grain yield and do without lime: however, under limed soil conditions all phosphates had some efficiency, except for the Gafsa phosphate in the first growing season. (Author) [pt

  8. DETERMINATION OF SUITABLE CHEMICAL EXTRACTION METHODS FOR AVAILABLE IRON CONTENT OF THE SOILS FROM EDIRNE PROVINCE IN TURKEY

    Directory of Open Access Journals (Sweden)

    A ADILOGLU

    2002-12-01

    Full Text Available The aim of this research was to determine the available iron (Fe content of the soils of Edirne Province and the most suitable chemical extraction method. Eight chemical extraction methods (0.005 M DTPA + 0.01 M CaCl2 + 0.1 M TEA; 0.05 M HCl + 0.012 M H2SO4; 1 M NH4OAc (pH: 4.8; 0.01 M EDTA + 1 M NH4OAc; 1 M MgCl2; 0.01 M EDTA + 1 M (NH42CO3; 0.005 M DTPA + 1 M NH4HCO3 and 0.001 M EDDHA methods and six biological indices (dry matter yield, Fe concentration, Fe uptake, relative dry matter yield, relative Fe concentration, relative Fe uptake were compared. Biological indices were determined with Barley (Hordeum vulgare L. grown under greenhouse conditions. At the end of the experiment, the highest correlation coefficients (r were determined to be between the 0.005 M DTPA + 0.01 M CaCl2 + 0.1 M TEA method and the biological indices and between the 0.005 M DTPA + 1 M NH4HCO3 method and the biological indices. The correlation coefficients (r for the 0.005 M DTPA + 0.01 M CaCl2 +0.1 M TEA method were r=0.621**; r=0.823**; r=0.810**; r=0.433**; r=0.558** and r=0.640** and for the 0.005 M DTPA + 1 M NH4HCO3 method r=0.618** ; r=0.520**; r=0.679**; r=0.521**; r=0.492** and r=0.641**, (**:p<0.01 respectively. These extraction methods, among all the methods tested were suggested for the determination of available Fe content of Edirne Province soils.

  9. Timing of Peripheral Blood Stem Cell Yield: Comparison of Alternative Methods with the Classic Method for CD34+ Cell Determination

    Directory of Open Access Journals (Sweden)

    I. Fatorova

    2014-01-01

    Full Text Available Hematopoietic stem cells (HSCs, still represent a certain mystery in biology, have a unique property of dividing into equal cells and repopulating the hematopoietic tissue. This potential enables their use in transplantation treatments. The quality of the HSC grafts for transplantation is evaluated by flow cytometric determination of the CD34+ cells, which enables optimal timing of the first apheresis and the acquisition of maximal yield of the peripheral blood stem cells (PBSCs. To identify a more efficient method for evaluating CD34+ cells, we compared the following alternative methods with the reference method: hematopoietic progenitor cells (HPC enumeration (using the Sysmex XE-2100 analyser, detection of CD133+ cells, and quantification of aldehyde dehydrogenase activity in the PBSCs. 266 aphereses (84 patients were evaluated. In the preapheretic blood, the new methods produced data that were in agreement with the reference method. The ROC curves have shown that for the first-day apheresis target, the optimal predictive cut-off value was 0.032 cells/mL for the HPC method (sensitivity 73.4%, specificity 69.3%. HPC method exhibited a definite practical superiority as compared to other methods tested. HPC enumeration could serve as a supplementary method for the optimal timing of the first apheresis; it is simple, rapid, and cheap.

  10. DETERMINATION OF THE YIELD OF COFFEE IN THE BASIC UNIT OF COOPERATIVE PRODUCTION (UBPC "LA JUBA" THROUGH ECONOMETRICS TECHNIQUE

    Directory of Open Access Journals (Sweden)

    Ramón Rodríguez-Betancourt

    2016-01-01

    Full Text Available In the Economic Program of the VI Congress of Comunist Party regarding the coffee agroindustry as agreement the following posittions: "To impel the development of the coffee activities to contribute to the gradual recovery of the traditional exportable funds". This sense, the process of planning the coffee harvest suggest the improvement of the fundamental indicators of this process. The coffee estimate is a primary indicator of harvest and other important indicators depend from him, among those the coffee production and the determination of other inputs of harvest. The objective of this work is to use econometrics technique, for the calculation of the coffee estimate in the Arabic variety in the UBPC "La Juba", belonging to the Coffee Company "Segundo Frente" It is demonstrated that using the econometrics technique the results comes closer to the real with more precision that the obtained by the  programmer, in 75 %. In a same way it is obtained as a result, the evaluation of the weight that it have in the yields the productive factors. In this case, when reconciling the analysis cost-benefit, with the study of the regression coefficients it was demonstrated that the most incident factor is the denominated Cultural Attentions. 

  11. NMR determination of chemically related metals in solution as a new method of inorganic analysis

    International Nuclear Information System (INIS)

    Fedorov, L.A.

    1989-01-01

    An NMR spectroscopic method for the determination of chemically related metals in solution is suggested. The metals are determined in complexes with specially selected polydentate ligands. Structural requirements to ligands, analytical properties and general limits of the application of the method are discussed. (orig.)

  12. Determination of kinetics and stoichiometry of chemical sulfide oxidation in wastewater of sewer networks

    DEFF Research Database (Denmark)

    Nielsen, Asbjørn Haaning; Vollertsen, Jes; Hvitved-Jacobsen, Thorkild

    2003-01-01

    A method for determination of kinetics and stoichiometry of chemical sulfide oxidation by dissolved oxygen (DO) in wastewater is presented. The method was particularly developed to investigate chemical sulfide oxidation in wastewater of sewer networks at low DO concentrations. The method is based...... be considered constant during the course of the experiments although intermediates accumulated. This was explained by an apparent slow oxidation rate of the intermediates. The method was capable of determining kinetics and stoichiometry of chemical sulfide oxidation at DO concentrations lower than 1 g of O2 m...... on continuous measurement of the reactants allowing the kinetics to be determined at varying reactant concentrations during the course of the experiment. The kinetics determined was simulated by a rate equation. The precision of the method was assessed in terms of the standard deviation of the kinetic...

  13. Influence of pre-sowing treatments by gamma rays on growth, yield and some chemical constituents of Sesamum indicum L

    Energy Technology Data Exchange (ETDEWEB)

    Hussein, O.S.; Hamideldin, N.

    2016-07-01

    The present work aims to improve the quantity and quality of seeds and/or seed oil by using low doses of radiation. Sesame seeds were exposed to ?- rays at levels of 30, 60 and 90 Gy. The results show that 30, 60 and 90 Gy doses activated most of growth and yield parameters significantly (weight of plant, number of capsules, weight of capsules/plant and weight of seeds/plant), with 60 Gy being the best dose. With regard to the total oil percentage in the produced crops, few changes have been observed, which did not reach the level of significance. The amount of unsaturated fatty acid (18:1, omega 9) was increase by 10.5% at a 30 Gy dose followed by 60 Gy (1.1%). The total of amino acid content showed that 30 Gy dose recorded the highest value (350.4 mg·g-1) followed by 60 Gy (285.6 mg·g-1) as compared to the control value (254.4 mg·g-1). The values of phosphorus, potassium magnesium and iron which represent the major minerals in sesame seeds were increased in the irradiated samples. (Author)

  14. Determination of solute organic concentration in contaminated soils using a chemical-equilibrium soil column system

    DEFF Research Database (Denmark)

    Gamst, Jesper; Kjeldsen, Peter; Christensen, Thomas Højlund

    2007-01-01

    using two soils with different content of organic carbon (f(oc) of 1.5 and 6.5%, respectively). A quadruple blind test of the ER-V system using glass beads in stead of soil showed an acceptable recovery (65-85%) of all of the 11 VOCs tested. Only for the most volatile compound (heptane, K-H similar...... to 80) an unacceptable recovery was found (9%). The contact time needed for obtaining chemical equilibrium was tested in the ER-H system by performing five test with different duration (1, 2, 4, 7 and 19 days) using the low organic carbon soil. Seven days of contact time appeared sufficient...... for determination of solute concentration in a contaminated soil were developed; (1) a chemical Equilibrium and Recirculation column test for Volatile organic chemicals (ER-V) and (2) a chemical Equilibrium and Recirculation column test for Hydrophobic organic chemicals (ER-H). The two test systems were evaluated...

  15. Exploratory study of fission product yield determination from photofission of 239Pu at 11 MeV with monoenergetic photons

    Science.gov (United States)

    Bhike, Megha; Tornow, W.; Krishichayan, Tonchev, A. P.

    2017-02-01

    Measurements of fission product yields play an important role for the understanding of fundamental aspects of the fission process. Recently, neutron-induced fission product-yield data of 239Pu at energies below 4 MeV revealed an unexpected energy dependence of certain fission fragments. In order to investigate whether this observation is prerogative to neutron-induced fission, a program has been initiated to measure fission product yields in photoinduced fission. Here we report on the first ever photofission product yield measurement with monoenergetic photons produced by Compton back-scattering of FEL photons. The experiment was performed at the High-Intensity Gamma-ray Source at Triangle Universities Nuclear Laboratory on 239Pu at Eγ=11 MeV. In this exploratory study the yield of eight fission products ranging from 91Sr to 143Ce has been obtained.

  16. Indirect Determination of Chemical Composition and Fuel Characteristics of Solid Waste

    DEFF Research Database (Denmark)

    Riber, Christian; Christensen, Thomas Højlund

    Determination of chemical composition of solid waste can be performed directly or indirectly by analysis of combustion products. The indirect methodology instrumented by a full scale incinerator is the only method that can conclude on elements in trace concentrations. These elements are of great...... interest in evaluating waste management options by for example LCA modeling. A methodology description of indirect determination of chemical composition and fuel properties of waste is provided and validated by examples. Indirect analysis of different waste types shows that the chemical composition...... is significantly dependent on waste type. And the analysis concludes that the transfer of substances in the incinerator is a function of waste chemical content, incinerator technology and waste physical properties. The importance of correct representation of rare items in the waste with high concentrations...

  17. Detailed balance method for chemical potential determination in Monte Carlo and molecular dynamics simulations

    International Nuclear Information System (INIS)

    Fay, P.J.; Ray, J.R.; Wolf, R.J.

    1994-01-01

    We present a new, nondestructive, method for determining chemical potentials in Monte Carlo and molecular dynamics simulations. The method estimates a value for the chemical potential such that one has a balance between fictitious successful creation and destruction trials in which the Monte Carlo method is used to determine success or failure of the creation/destruction attempts; we thus call the method a detailed balance method. The method allows one to obtain estimates of the chemical potential for a given species in any closed ensemble simulation; the closed ensemble is paired with a ''natural'' open ensemble for the purpose of obtaining creation and destruction probabilities. We present results for the Lennard-Jones system and also for an embedded atom model of liquid palladium, and compare to previous results in the literature for these two systems. We are able to obtain an accurate estimate of the chemical potential for the Lennard-Jones system at higher densities than reported in the literature

  18. Effect of jasmonic acid elicitation on the yield, chemical composition, and antioxidant and anti-inflammatory properties of essential oil of lettuce leaf basil (Ocimum basilicum L.).

    Science.gov (United States)

    Złotek, Urszula; Michalak-Majewska, Monika; Szymanowska, Urszula

    2016-12-15

    The effect of elicitation with jasmonic acid (JA) on the plant yield, the production and composition of essential oils of lettuce leaf basil was evaluated. JA-elicitation slightly affected the yield of plants and significantly increased the amount of essential oils produced by basil - the highest oil yield (0.78±0.005mL/100gdw) was achieved in plants elicited with 100μM JA. The application of the tested elicitor also influenced the chemical composition of basil essential oils - 100μM JA increased the linalool, eugenol, and limonene levels, while 1μM JA caused the highest increase in the methyl eugenol content. Essential oils from JA-elicited basil (especially 1μM and 100μM) exhibited more effective antioxidant and anti-inflammatory potential; therefore, this inducer may be a very useful biochemical tool for improving production and composition of herbal essential oils. Copyright © 2016 Elsevier Ltd. All rights reserved.

  19. Effect of gamma irradiation on growth, yield and chemical constituents for three tomato varieties and their crosses

    Energy Technology Data Exchange (ETDEWEB)

    Hassanien, E H; Abdeltawab, F M; Elsouedy, A [Department of Genetics, Faculty of Agriculture, Ain shams University, Cairo (Egypt); Sharabash, M T; Mahmoud, A A [National Center for Research and Radiation Technology, Atomic Energy Authority, Cairo (Egypt)

    1995-10-01

    Three tomato varieties named no. 10 (I); bison (II) and Kecskement (III),as well as their crosses and their reciprocal crosses were irradiated and involved in this investigation. Variety (II) was the earliest in flowering, The shortest stem with the least number of branches per plant. Whereas variety (III) was the latest latest in flowering, the longest stem with the highest number of branches per plant. Meanwhile, variety (I) was in the intermediate between the other 2 varieties. Generally, days for 50% flowering were decreased for all varieties and all genotypes as a function of gamma irradiation. This response reached the maximum in M2. Whereas, plant height and number of branches did not gain the same trend. Variety (I) produced the highest number of fruits per plant, while variety (III) gained the lowest. The average weight of fruit was in reversal correlation with the average number of fruits per plant. All crosses and their reciprocal crosses were almost intermediate between their parents in number of fruits per plant, average fruit weight, fruit yield per plant, and seed setting per fruit. Irradiating seeds of tomato varieties and expected crosses stimulated the fruit characters, however, they were still less than the best parent. This enhancement was extended to M2. Variety (I) verified the highest concentration of vitamin. C, and chlorophyll A, B and carotenoids in leaves, comparing to the other 2 varieties. Meanwhile, lycopene in fruits reached the maximum concentration in variety (III). All genotypes obtained could not exceed their respective parents in vitamin. C except the crosses (I x II), (I x III),(II x III) and (III x II) which overcame their original parents, particularly in M2. Meanwhile all crosses, as well as, their reciprocal crosses could not gain the prominancy in both lycopene and carotenoids over the best parent. Vitamin. C, and lycopene in fruits were decreased decreased in fruits as a function of gamma irradiation. (Abstract Truncated)

  20. Determination of trapping parameters and the chemical diffusion coefficient from hydrogen permeation experiments

    International Nuclear Information System (INIS)

    Svoboda, J.; Mori, G.; Prethaler, A.; Fischer, F.D.

    2014-01-01

    Highlights: • A modeling study for diffusion of hydrogen with traps is presented. • Introduction of a new chemical diffusion coefficient. • Density of traps and average depth of traps can be determined. • Lattice diffusion and sub-surface concentration of atomic hydrogen can be determined. - Abstract: An improved diffusion theory accounting for trapping effects is applied to evaluation of hydrogen permeation experiments performed for pure iron and pearlitic and martensitic steels. The trapping parameters as molar volume and depth of traps are determined by fitting experiments by simulations based on the theory. The concentration-dependent chemical diffusion coefficient of hydrogen is extracted indicating that the trapping effect on diffusion in pure iron and pearlitic steel is negligible. However, it is significant for martensitic steel, for which the chemical diffusion coefficient cannot be considered as concentration-independent as it is established in current standards

  1. [Research on determination of chemical purity of andrographolide by coulometric titration method].

    Science.gov (United States)

    Yang, Ning; Yang, Dezhi; Xu, Lishen; Lv, Yang

    2010-04-01

    The determination of chemical purity of andrographolide by coulometric titration method is studied in this paper. The coulometric titration was carried out in a mixture composed of 4 mol x L(-1) hydrochloric acid and 1 mol x L(-1) potassium bromide solution and 1 mol x L(-1) potassium nitrate solution (1:1). Bromine is electrogenerated at the anode and reacts with the andrographolide. The number of electrons involved in the eleatrode reaction is 2. Purity of andrographolide is 99.76% compared with 99.77% utilizing area normalization method by HPLC. The RSD are 0.33% and 0.02% respectively. The results from two methods are consistent, so the determination of chemical purity of andrographolide by coulometric titration method is scientific and feasible. The method is rapid, simple, convenient, sensitive and accurate. The reference material is not essential in the method. The method is suitable for determination of chemical purity of andrographolide.

  2. Determination of mustard and lewisite related compounds in abandoned chemical weapons (Yellow shells) from sources in China and Japan.

    Science.gov (United States)

    Hanaoka, Shigeyuki; Nomura, Koji; Wada, Takeharu

    2006-01-06

    Knowledge of the states of the contents in chemical munitions that Japanese Imperial Forces abandoned at the end of World War II in Japan and China is gravely lacking. To unearth and recover these chemical weapons and detoxify the contents safely, it is essential to establish analytical procedures to definitely determine the CWA contents. We established such a procedure and applied it to the analysis of chemicals in the abandoned shells. Yellow shells are known to contain sulfur mustard, lewisite, or a mixture of both. Lewisite was analyzed without thiol derivatization, because it and its decomposition products yield the same substances in the derivatization. Analysis using our new procedure showed that both mustard and lewisite remained as the major components after the long abandonment of nearly 60 years. The content of mustard was 43% and that of lewisite 55%. The viscous material found was suggested to be mostly oligomers of mustard. Comparison of the components in the Yellow agents with mustard recovered in both Japan and China showed a difference in the impurities between the CWAs produced by the former Imperial navy and those by the former Imperial army.

  3. Effect of gamma irradiation on growth, yield and chemical constituents for three tomato varieties and their crosses

    International Nuclear Information System (INIS)

    Hassanien, E.H.; Abdeltawab, F.M.; Elsouedy, A.; Sharabash, M.T.; Mahmoud, A.A.

    1995-01-01

    Three tomato varieties named no. 10 (I); bison (II) and Kecskement (III),as well as their crosses and their reciprocal crosses were irradiated and involved in this investigation. Variety (II) was the earliest in flowering, The shortest stem with the least number of branches per plant. Whereas variety (III) was the latest latest in flowering, the longest stem with the highest number of branches per plant. Meanwhile, variety (I) was in the intermediate between the other 2 varieties. Generally, days for 50% flowering were decreased for all varieties and all genotypes as a function of gamma irradiation. This response reached the maximum in M2. Whereas, plant height and number of branches did not gain the same trend. Variety (I) produced the highest number of fruits per plant, while variety (III) gained the lowest. The average weight of fruit was in reversal correlation with the average number of fruits per plant. All crosses and their reciprocal crosses were almost intermediate between their parents in number of fruits per plant, average fruit weight, fruit yield per plant, and seed setting per fruit. Irradiating seeds of tomato varieties and expected crosses stimulated the fruit characters, however, they were still less than the best parent. This enhancement was extended to M2. Variety (I) verified the highest concentration of vitamin. C, and chlorophyll A, B and carotenoids in leaves, comparing to the other 2 varieties. Meanwhile, lycopene in fruits reached the maximum concentration in variety (III). All genotypes obtained could not exceed their respective parents in vitamin. C except the crosses (I x II), (I x III),(II x III) and (III x II) which overcame their original parents, particularly in M2. Meanwhile all crosses, as well as, their reciprocal crosses could not gain the prominancy in both lycopene and carotenoids over the best parent. Vitamin. C, and lycopene in fruits were decreased decreased in fruits as a function of gamma irradiation. This was true for all

  4. Determination of the biogas and methane yield of selected energy crops. [NAchWAchsende ROhstoffe]; Ermittlung der Biogas- und Methanausbeute ausgewaehlter Nawaro

    Energy Technology Data Exchange (ETDEWEB)

    Ohl, Susanne

    2011-11-15

    The aim of this paper is the characterization of substrate quality and methane yield of different energy crops, which were cultivated in Schleswig-Holstein. The specific methane production of 224 variants was determined in with Hohenheim biogas yield test (HBT), 72 variants were investigated in a common batch test. The specific methane production (HBT) is 359-371 l{sub N}/kg{sub oDM} for wheat, 358-378 l{sub N}/kg{sub oDM} for maize and 341-372 l{sub N}/kg{sub oDM} for perennial ryegrass. The results for the specific methane production are due to a systematic offset in the batch experiment always below those of the HBT. Silages achieve higher gas yields than fresh substrates. The mass losses, which occur during ensiling, were compensated due to the higher gas yields. Maize is compared with other energy crops superior in terms of the yield per hectare. The experimentally determined methane yields showed a good agreement with calculated theoretical methane yields (method of WEIssBACH 2008, 2009).

  5. Determination of relative krypton fission product yields from 14 MeV neutron induced fission of 238U at the National Ignition Facility.

    Science.gov (United States)

    Edwards, E R; Cassata, W S; Velsko, C A; Yeamans, C B; Shaughnessy, D A

    2016-11-01

    Precisely-known fission yield distributions are needed to determine a fissioning isotope and the incident neutron energy in nuclear security applications. 14 MeV neutrons from DT fusion at the National Ignition Facility induce fission in depleted uranium contained in the target assembly hohlraum. The fission yields of Kr isotopes (85m, 87, 88, and 89) are measured relative to the cumulative yield of 88 Kr and compared to previously tabulated values. The results from this experiment and England and Rider are in agreement, except for the 85m Kr/ 88 Kr ratio, which may be the result of incorrect nuclear data.

  6. The application dosage of Azolla pinnata in fresh and powder form as organic fertilizer on soil chemical properties, growth and yield of rice plant

    Science.gov (United States)

    Setiawati, Mieke Rochimi; Damayani, Maya; Herdiyantoro, Diyan; Suryatmana, Pujawati; Anggraini, Derisfha; Khumairah, Fiqriah Hanum

    2018-02-01

    The yield of rice plants is strongly influenced by N fertilizer. Nitrogen in rice plants has roles in vegetative growth, tiller formation and increasing yield through rice protein formation. Nitrogen supplied from organic fertilizers is better than inorganic fertilizers that may have environmental problem effects. Organic fertilizers from Azolla pinnata water fern contain higher N than other organic fertilizers. Symbiosis between A. pinnata and the N-fixing cyanobacteria results in high content of nitrogen, 3 to 5%. A. pinnata can be added to the rice field as organic fertilizer in form of fresh biomass or composted. Composted form can be ground into powder which passes through 100 mesh sieve. Preparation of compost powder of A. pinnata is done to reduce the constraints of voluminous application of organic fertilizers and to improve the efficiency of its use. The objective of this research was to compare the effect of the use of fresh A. pinnata and compost powder of A. pinnata on some soil and plant chemical properties and rice yield. The treatments applied were fresh A. pinnata at the dose of 0, 10 and 20 ton ha-1 and A. pinnata compost powder at 12.5 and 25 kg ha-1. The results showed that incorporation of fresh A. pinnata at 20 tons ha-1 and its compost powder at 25 kg ha-1 increased the available P of soil, plant P content and tiller number, but did not affect the content of organic-C, total soil N, plant N content and rice yield. This study suggested the benefits of A. pinnata compost powder technology in organic fertilization of soil to increase the nutrient content of soil and rice plants.

  7. Determination of chemical oxygen demand (COD) using an alternative wet chemical method free of mercury and dichromate.

    Science.gov (United States)

    Kolb, Marit; Bahadir, Müfit; Teichgräber, Burkhard

    2017-10-01

    Worldwide, the standard methods for the determination of the important wastewater parameter chemical oxygen demand (COD) are still based on the use of the hazardous chemicals, mercury sulfate and chromium(VI). However, due to their properties they are meanwhile classified as "priority pollutants" and shall be phased out or banned in the frame of REACH (current European Chemical Law: Registration, Evaluation, Authorization and restriction of Chemicals) by the European Union. Hence, a new wet-chemical method free of mercury and chromium(VI) was developed. Manganese(III) was used as oxidant and silver nitrate for the removal of chloride ions. The quantification was performed by back titration of manganese(III) with iron(II) as done in the standard method. In order to minimize losses of organic substances during the precipitation of silver chloride, suspended and colloid organic matter had to be separated by precipitation of aluminum hydroxide in a first step. In these cases, two fractions, one of the suspended and colloid matters and a second of the dissolved organic substances, are prepared and oxidized separately. The method was tested with potassium hydrogen phthalate (KHP) as conventional COD reference substance and different types of wastewater samples. The oxidation of KHP was reproducible in a COD range of 20-500 mg/L with a mean recovery rate of 88.7% in comparison to the standard COD method (DIN 38409-41). Also in presence of 1000 mg/L chloride a recovery rate of 84.1% was reached. For a series of industrial and municipal wastewater samples a high correlation (R 2  = 0.9935) to the standard method with a mean recovery rate of 78.1% (±5.2%) was determined. Even though the results of the new method are not 100% of the standard method, its high correlation to the standard method and reproducibility offers an environmentally benign alternative method with no need to purchase new laboratory equipment. Copyright © 2017 Elsevier Ltd. All rights reserved.

  8. Method for Non-Invasive Determination of Chemical Properties of Aqueous Solutions

    Science.gov (United States)

    Todd, Paul W. (Inventor); Jones, Alan (Inventor); Thomas, Nathan A. (Inventor)

    2016-01-01

    A method for non-invasively determining a chemical property of an aqueous solution is provided. The method provides the steps of providing a colored solute having a light absorbance spectrum and transmitting light through the colored solute at two different wavelengths. The method further provides the steps of measuring light absorbance of the colored solute at the two different transmitted light wavelengths, and comparing the light absorbance of the colored solute at the two different wavelengths to determine a chemical property of an aqueous solution.

  9. A composite of complex and chemical hydrides yields the first Al-based amidoborane with improved hydrogen storage properties.

    Science.gov (United States)

    Dovgaliuk, Iurii; Jepsen, Lars H; Safin, Damir A; Łodziana, Zbigniew; Dyadkin, Vadim; Jensen, Torben R; Devillers, Michel; Filinchuk, Yaroslav

    2015-10-05

    The first Al-based amidoborane Na[Al(NH2 BH3 )4 ] was obtained through a mechanochemical treatment of the NaAlH4 -4 AB (AB=NH3 BH3 ) composite releasing 4.5 wt % of pure hydrogen. The same amidoborane was also produced upon heating the composite at 70 °C. The crystal structure of Na[Al(NH2 BH3 )4 ], elucidated from synchrotron X-ray powder diffraction and confirmed by DFT calculations, contains the previously unknown tetrahedral ion [Al(NH2 BH3 )4 ](-) , with every NH2 BH3 (-) ligand coordinated to aluminum through nitrogen atoms. Combination of complex and chemical hydrides in the same compound was possible due to both the lower stability of the AlH bonds compared to the BH ones in borohydride, and due to the strong Lewis acidity of Al(3+) . According to the thermogravimetric analysis-differential scanning calorimetry-mass spectrometry (TGA-DSC-MS) studies, Na[Al(NH2 BH3 )4 ] releases in two steps 9 wt % of pure hydrogen. As a result of this decomposition, which was also supported by volumetric studies, the formation of NaBH4 and amorphous product(s) of the surmised composition AlN4 B3 H(0-3.6) were observed. Furthermore, volumetric experiments have also shown that the final residue can reversibly absorb about 27 % of the released hydrogen at 250 °C and p(H2 )=150 bar. Hydrogen re-absorption does not regenerate neither Na[Al(NH2 BH3 )4 ] nor starting materials, NaAlH4 and AB, but rather occurs within amorphous product(s). Detailed studies of the latter one(s) can open an avenue for a new family of reversible hydrogen storage materials. Finally, the NaAlH4 -4 AB composite might become a starting point towards a new series of aluminum-based tetraamidoboranes with improved hydrogen storage properties such as hydrogen storage density, hydrogen purity, and reversibility. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Effect of molecular weight on radiation chemical degradation yield of chain scission of γ-irradiated chitosan in solid state and in aqueous solution

    International Nuclear Information System (INIS)

    Tahtat, Djamel; Mahlous, Mohamed; Benamer, Samah; Nacer Khodja, Assia; Larbi Youcef, Souad

    2012-01-01

    Chitosan A 1 , A 2 and A 3 with molecular weight of 471, 207 and 100 kDa respectively, produced from squid pen chitin was degraded by gamma rays in the solid state and in aqueous solution with various doses in air at ambient temperature. Effect of molecular weight on radiation chemical degradation yield of chain scission and degradation rate constants of γ-irradiated chitosan in solid state and in aqueous solution was investigated. The radiation chemical degradation yield G (s) and degradation rate values were calculated. The molecular weight changes were monitored by capillary viscometry method and the chemical structure changes were followed by UV analysis. The results showed that, the degradation of chitosan was faster in solution, than in solid state. The values of G (s) in solid state and in aqueous solution were respectively 1.1×10 −8 mol/J and 0.074×10 −7 mol/J for A 1 , 4.42×10 −8 mol/J and 0.28×10 −7 mol/J for A 2 and 6.08×10 −8 mol/J and 0.38×10 −7 mol/J for A 3 . Degradation rate constants values ranged from 0.41×10 −5 to 2.1×10 −5 kGy −1 in solid state, whereas in solution they ranged from 13×10 −5 to 68×10 −5 kGy −1 . The chitosan A 3 was more sensitive to radiolysis than A 1 and A 2 . The chain scission yield, G (s) and degradation rate constants seems to be greatly influenced by the initial molecular weight of the chitosan. Structural changes in irradiated chitosan are revealed by the apparition of absorption peaks at 261 and 295 nm, which could be attributed to the formation of carbonyl groups. In both conditions the peak intensity was higher in chitosan A 3 than in A 1 and A 2 , the oxidative products decreased with increasing molecular weight of chitosan. - Highlights: ► We investigated the effects of MW on G (s) value of γ-irradiated chitosan in solid and aqueous state. ► Chitosan with low molecular weight was more sensitive to radiolysis than high molecular weight. ► G (s) value and degradation rate

  11. YIELD CAPACITY AND CHEMICAL COMPOSITION OF GREEN BEANS IN CULTIVARS OF KIDNEY BEAN BRED AT OMSK AGRARIAN UNIVERSITY IN THE SOUTH FOREST-STEPPE OF WESTERN SIBERIA

    Directory of Open Access Journals (Sweden)

    N. G. Kazydub

    2017-01-01

    Full Text Available In  2014-2016  the  assessment of  kidney bean  cultivars bred at Omsk State Agrarian University on yield capacity, quality, and biochemical  chemical compounds  in green beans, such as proteins, zinc, iodine, iron and sucrose was carried  out  in  the  south  forest-steppe  of  Western Siberia. The technological  parameters of  green  beans: the  shape  of  cross-section  area; pulpiness,  fibrous  or non-fibrous,  and bean thickness were estimated. Threeyear study showed that all tested cultivars bred at Omsk State  Agrarian  University  surpassed  control  cultivar  in yield capacity,  chemical composition  and technological parameters of green beans. The cultivar ‘Pamiyaty Rizhovoy’ gave a highest yield: 563.4 g/m2  in 2014; 622.8 g/m2 in 2015; and 620.4 g/m2  in 2016. It is worth noticing that this cultivar is also distinguished by contents of micro and macroelements: 21.20-28.68  mg/kg  of zinc; 0.012-0.018 mg/kg of iodine; and 1.8-3.2 mg/kg of iron. In the course of the study, it was noticed the dependence of  yield  capacity  on  hydrothermal  coefficient  (HC. In 2014-2015 the yield capacity was a lowest when the moisturization was insufficient at 0.7 HC. With increase of HC the yield was higher. With sufficient moisturization at 1.0 HC the highest yield of green beans was observed in 2016.  The estimation  of  kidney  bean  cultivars  bred  at Omsk State  Agrarian University showed  that  all beans were  distinguished  by  high  quality  parameters  in  the phase  of  technical  maturity,  such  as  pulpiness,  nonfibrous, thickness 0.5 to  1.0 cm, and green and yellow colors.  The  highest  protein  content  comparing  to  the control  cultivar  ‘Zolushka’  was  detected  in  ‘Marusya’ 23.60%  in  2014,  20.94%  in  2015;  and  ‘Zoloto  Sibiry’ 19.79%  in  2016.  The  observed  results  confirmed  that contents  change of

  12. Chemical modifiers in electrothermal atomic absorption determination of Platinum and Palladium containing preparations in blood serum

    Directory of Open Access Journals (Sweden)

    Аntonina Alemasova

    2012-11-01

    Full Text Available The biological liquids matrixes influence on the characteristic masses and repeatability of Pt and Pd electrothermal atomic absorption spectroscopy (ETAAS determination was studied. The chemical modifiers dimethylglyoxime and ascorbic acid for matrix interferences elimination and ETAAS results repeatability improvement were proposed while bioliquids ETAAS analysis, and their action mechanism was discussed.

  13. Determination of yield and erosion damage functions using subjectively elicited data: application to smallholder tea in Sri Lanka

    OpenAIRE

    Ananda, Jayanath; Herath, Gamini; Chisholm, Anthony H.

    2001-01-01

    Tea has been Sri Lanka’s major export earner for several decades. However, soil erosion on tea‐producing land has had considerable on‐site and off‐site effects. This study quantifies soil erosion impacts for smallholder tea farms in Sri Lanka by estimating a yield damage function and an erosion damage function using a subjective elicitation technique. The Mitscherlich‐Spillman type of function was found to yield acceptable results. The study indicates that high rates of soil erosion require e...

  14. EDXRF for determination of chemical elements in the beetle Alphitobius diaperinus

    International Nuclear Information System (INIS)

    Cantinha, Rebeca S.; Farias, Emerson E.G. de; Magalhaes, Marcelo L.R. de; Franca, Elvis J. de; Cunha, Franklin M. da; Zacarias, Vyvyane L.

    2015-01-01

    Energy Dispersion X-Ray Fluorescence (EDXRF) spectrometry has been widely employed for chemical element determination of biological matrices, including insects. The beetle Alphitobius diaperinus is a major problem in poultry production, thereby infesting poultry litter and stored grains. Up to now, little is known about the behavior, physiology and environmental interactions of this insect. In this paper, EDXRF was applied to quantify the main chemical elements in A. diaperinus. For the quality of the analytical protocol, certified reference materials produced by National Institute of Standards and Technology - NIST were analyzed together with the samples. The technique was able to quantify Cl, P, S and Zn in this insect, presenting no significant variation at the 95% confidence level among the repetitions (n = 4). A different pattern of chemical element accumulation in this beetle was noticed compared to other Coleoptera species, in which the concentration of the chemical elements were markedly lower in A. diaperinus, probably associated to the restricted availability of chemical elements in food. Since no result has been found in the literature before, A. diaperinus was firstly chemically characterized in this paper. (author)

  15. EDXRF for determination of chemical elements in the beetle Alphitobius diaperinus

    Energy Technology Data Exchange (ETDEWEB)

    Cantinha, Rebeca S.; Farias, Emerson E.G. de; Magalhaes, Marcelo L.R. de; Franca, Elvis J. de, E-mail: rebecanuclear@gmail.com, E-mail: emersonemiliano@yahoo.com.br, E-mail: marcelo_rlm@hotmail.com, E-mail: ejfranca@cnen.gov.br [Centro Regional de Ciencias Nucleares do Nordeste (CRCN-NE/CNEN-PE), Recife, PE (Brazil); Cunha, Franklin M. da; Zacarias, Vyvyane L., E-mail: ukento@yahoo.com.br, E-mail: vyvyanebiologicas@gmail.com [Universidade Federal Rural de Pernambuco (UFRPE), Recife, PE (Brazil)

    2015-07-01

    Energy Dispersion X-Ray Fluorescence (EDXRF) spectrometry has been widely employed for chemical element determination of biological matrices, including insects. The beetle Alphitobius diaperinus is a major problem in poultry production, thereby infesting poultry litter and stored grains. Up to now, little is known about the behavior, physiology and environmental interactions of this insect. In this paper, EDXRF was applied to quantify the main chemical elements in A. diaperinus. For the quality of the analytical protocol, certified reference materials produced by National Institute of Standards and Technology - NIST were analyzed together with the samples. The technique was able to quantify Cl, P, S and Zn in this insect, presenting no significant variation at the 95% confidence level among the repetitions (n = 4). A different pattern of chemical element accumulation in this beetle was noticed compared to other Coleoptera species, in which the concentration of the chemical elements were markedly lower in A. diaperinus, probably associated to the restricted availability of chemical elements in food. Since no result has been found in the literature before, A. diaperinus was firstly chemically characterized in this paper. (author)

  16. k{sub 0}-INAA for determining chemical elements in bird feathers

    Energy Technology Data Exchange (ETDEWEB)

    Franca, Elvis J., E-mail: ejfranca@usp.b [CENA/USP, Centro de Energia Nuclear na Agricultura, Universidade of Sao Paulo, P.O. Box 97, 13400-970, Piracicaba, SP (Brazil); Fernandes, Elisabete A.N.; Fonseca, Felipe Y. [CENA/USP, Centro de Energia Nuclear na Agricultura, Universidade of Sao Paulo, P.O. Box 97, 13400-970, Piracicaba, SP (Brazil); Antunes, Alexsander Z. [IF, Instituto Florestal do Estado de Sao Paulo, Rua do Horto 931, Horto Florestal 02377-000, Sao Paulo, SP (Brazil); Bardini Junior, Claudiney; Bacchi, Marcio A.; Rodrigues, Vanessa S.; Cavalca, Isabel P.O. [CENA/USP, Centro de Energia Nuclear na Agricultura, Universidade of Sao Paulo, P.O. Box 97, 13400-970, Piracicaba, SP (Brazil)

    2010-10-11

    The k{sub 0}-method instrumental neutron activation analysis (k{sub 0}-INAA) was employed for determining chemical elements in bird feathers. A collection was obtained taking into account several bird species from wet ecosystems in diverse regions of Brazil. For comparison reason, feathers were actively sampled in a riparian forest from the Marins Stream, Piracicaba, Sao Paulo State, using mist nets specific for capturing birds. Biological certified reference materials were used for assessing the quality of analytical procedure. Quantification of chemical elements was performed using the k{sub 0}-INAA Quantu Software. Sixteen chemical elements, including macro and micronutrients, and trace elements, have been quantified in feathers, in which analytical uncertainties varied from 2% to 40% depending on the chemical element mass fraction. Results indicated high mass fractions of Br (max=7.9 mg kg{sup -1}), Co (max=0.47 mg kg{sup -1}), Cr (max=68 mg kg{sup -1}), Hg (max=2.79 mg kg{sup -1}), Sb (max=0.20 mg kg{sup -1}), Se (max=1.3 mg kg{sup -1}) and Zn (max=192 mg kg{sup -1}) in bird feathers, probably associated with the degree of pollution of the areas evaluated. In order to corroborate the use of k{sub 0}-INAA results in biomonitoring studies using avian community, different factor analysis methods were used to check chemical element source apportionment and locality clustering based on feather chemical composition.

  17. EDF's approach to determine specifications for nuclear power plant bulk chemicals

    International Nuclear Information System (INIS)

    Basile, Alix; Dijoux, Michel; Le-Calvar, Marc; Gressier, Frederic; Mole, Didier

    2012-09-01

    Chemical impurities in the primary, secondary and auxiliary nuclear power plants circuits generate risks of corrosion of the fuel cladding, steel and nickel based alloys. The PMUC (Products and Materials Used in plants) organization established by EDF intends to limit this risk by specifying maximum levels of impurities in products and materials used for the operation and maintenance of Nuclear Power Plants (NPPs). Bulk chemicals specifications, applied on primary and secondary circuit chemicals and hydrogen and nitrogen gases, are particularly important to prevent chemical species to be involved in the corrosion of the NPPs materials. The application of EDF specifications should lead to reasonably exclude any risk of degradation of the first and second containment barriers and auxiliary circuits Important to Safety (IPS) by limiting the concentrations of chlorides, fluorides, sulfates... The risk of metal embrittlement by elements with low melting point (mercury, lead...) is also included. For the primary circuit, the specifications intend to exclude the risk of activation of impurities introduced by the bulk chemicals. For the first containment barrier, to reduce the risk of deposits like zeolites, PMUC products specifications set limit values for calcium, magnesium, aluminum and silica. EDF's approach for establishing specifications for bulk chemicals is taking also into account the capacity of industrial production, as well as costs, limitations of analytical control methods (detection limits) and environmental releases issues. This paper aims to explain EDF's approach relative to specifications of impurities in bulk chemicals. Also presented are the various parameters taken into account to determine the maximum pollution levels in the chemicals, the theoretical hypothesis to set the specifications and the calculation method used to verify that the specifications are suitable. (authors)

  18. Impact of Addition of FGDB as a Soil Amendment on Physical and Chemical Properties of an Alkali Soil and Crop Yield of Maize in Northern China Coastal Plain

    Directory of Open Access Journals (Sweden)

    H.-L. Yu

    2015-01-01

    Full Text Available To evaluate the effect of Flue gas desulfurization byproduct( FGDB as a soil amendment on growth and yield of maize (Zea mays and to determine the impact of FGDB additions on soil fertility characteristics in alkaline clayey soils, a 2-year field experiment was conducted in Huanghua, in Northern China Coastal Plain. The experiment included five treatments in which the soil was amended with FGDB at 15 cm depth at the rates of 0 t·hm−2, 4.50 t·hm−2, 9.00 t·hm−2, 13.5 t·hm−2, and 18.00 t·hm−2, respectively, before maize was planted. The values of soil pH, exchangeable sodium percentage (ESP, and bulk density (BD of the soil decreased; however, values of electrical conductivity (EC, water holding capacity (WHC, and plant nutrients increased with FGDB application in the soil. Crop plants grow more readily in FGDB amended soils because of improved soil properties. The best ameliorative effect was obtained at the rate of 13.5 t·hm−2. The germination percentage, plant height, and crop yield successively increased in both years. The results indicated FGDB was an effective soil amendment for improving the physicochemical properties and nutrient balance, and enhancing crop germination, growth, and yield, particularly when applied at a suitable application rate.

  19. Determination of Gibbs energies of formation in aqueous solution using chemical engineering tools.

    Science.gov (United States)

    Toure, Oumar; Dussap, Claude-Gilles

    2016-08-01

    Standard Gibbs energies of formation are of primary importance in the field of biothermodynamics. In the absence of any directly measured values, thermodynamic calculations are required to determine the missing data. For several biochemical species, this study shows that the knowledge of the standard Gibbs energy of formation of the pure compounds (in the gaseous, solid or liquid states) enables to determine the corresponding standard Gibbs energies of formation in aqueous solutions. To do so, using chemical engineering tools (thermodynamic tables and a model enabling to predict activity coefficients, solvation Gibbs energies and pKa data), it becomes possible to determine the partial chemical potential of neutral and charged components in real metabolic conditions, even in concentrated mixtures. Copyright © 2016 Elsevier Ltd. All rights reserved.

  20. Determining the Threshold Value of Basil Yield Reduction and Evaluation of Water Uptake Models under Salinity Stress Condition

    OpenAIRE

    M. Sarai Tabrizi; H. Babazadeh; M. Homaee; F. Kaveh Kaveh; M. Parsinejad

    2016-01-01

    Introduction: Several mathematical models are being used for assessing the plant response to the salinity of the root zone. The salinity of the soil and water resources is a major challenge for agricultural sector in Iran. Several mathematical models have been developed for plant responses to the salinity stress. However, these models are often applicable in particular conditions. The objectives of this study were to evaluate the threshold value of Basil yield reduction, modeling Basil respon...

  1. Determining the Threshold Value of Basil Yield Reduction and Evaluation of Water Uptake Models under Salinity Stress Condition

    Directory of Open Access Journals (Sweden)

    M. Sarai Tabrizi

    2016-10-01

    Full Text Available Introduction: Several mathematical models are being used for assessing the plant response to the salinity of the root zone. The salinity of the soil and water resources is a major challenge for agricultural sector in Iran. Several mathematical models have been developed for plant responses to the salinity stress. However, these models are often applicable in particular conditions. The objectives of this study were to evaluate the threshold value of Basil yield reduction, modeling Basil response to salinity and to evaluate the effectiveness of available mathematical models for the yield estimation of the Basil . Materials and Methods: The extensive experiments were conducted with 13 natural saline water treatments including 1.2, 1.8, 2, 2.2, 2.5, 2.8, 3, 3.5, 4, 5, 6, 8, and 10 dSm-1. Water salinity treatments were prepared by mixing Shoor River water with fresh water. In order to quantify the salinity effect on Basil yield, seven mathematical models including Maas and Hoffman (1977, van Genuchten and Hoffman (1984, Dirksen and Augustijn (1988, and Homaee et al., (2002 were used. One of the relatively recent methods for soil water content measurements is theta probes instrument. Theta probes instrument consists of four probes with 60 mm long and 3 mm diameter, a water proof container (probe structure, and a cable that links input and output signals to the data logger display. The advantages that have been attributed to this method are high precision and direct and rapid measurements in the field and greenhouse. The range of measurements is not limited like tensiometer and is from saturation to wilting point. In this study, Theta probes instrument was calibrated by weighing method for exact irrigation scheduling. Relative transpiration was calculated using daily soil water content changes. A coarse sand layer with 2 centimeters thick was used to decrease evaporation from the surface soil of the pots. Quantity comparison of the used models was done

  2. The OsSPL16-GW7 regulatory module determines grain shape and simultaneously improves rice yield and grain quality.

    Science.gov (United States)

    Wang, Shaokui; Li, Shan; Liu, Qian; Wu, Kun; Zhang, Jianqing; Wang, Shuansuo; Wang, Yi; Chen, Xiangbin; Zhang, Yi; Gao, Caixia; Wang, Feng; Huang, Haixiang; Fu, Xiangdong

    2015-08-01

    The deployment of heterosis in the form of hybrid rice varieties has boosted grain yield, but grain quality improvement still remains a challenge. Here we show that a quantitative trait locus for rice grain quality, qGW7, reflects allelic variation of GW7, a gene encoding a TONNEAU1-recruiting motif protein with similarity to C-terminal motifs of the human centrosomal protein CAP350. Upregulation of GW7 expression was correlated with the production of more slender grains, as a result of increased cell division in the longitudinal direction and decreased cell division in the transverse direction. OsSPL16 (GW8), an SBP-domain transcription factor that regulates grain width, bound directly to the GW7 promoter and repressed its expression. The presence of a semidominant GW7(TFA) allele from tropical japonica rice was associated with higher grain quality without the yield penalty imposed by the Basmati gw8 allele. Manipulation of the OsSPL16-GW7 module thus represents a new strategy to simultaneously improve rice yield and grain quality.

  3. Determination of suitable chemical extraction methods for the available iron content of brown forest soils in Turkey

    Science.gov (United States)

    Adiloglu, Aydin

    2006-09-01

    The aim of this research was to determine the available iron (Fe) content of brown forest soils of Edirne Province and the most suitable chemical extraction method. Eight chemical extraction methods (the 0.005 M DTPA + 0.01 M CaCl2 + 0.1 MTEA, 0.05 M HCl + 0.012 M H2SO4, 1 M NH4OAc (pH: 4.8), 0.01 M EDTA + 1 M NH4OAc, 1 M MgCl2, 0.01 M EDTA + 1 M (NH4)2CO3, 0.005 M DTPA + 1 M NH4HCO3, and 0.001 M EDDHA methods) and six biological indices (the dry matter yield, Fe concentration, Fe uptake, relative dry matter yield, relative Fe concentration, and relative Fe uptake) were compared. The biological indices were determined with barley (Hordeum vulgare L.) grown under greenhouse conditions. At the end of the experiment, the highest correlation coefficients (r) were determined to be between the 0.005 M DTPA + 0.01 M CaCl2 + 0.1 M TEA method and the biological indices and between the 0.005 M DTPA + 1 M NH4HCO3 method and the biological indices. The corresponding correlation coefficients (r) for the 0.005 M DTPA + 0.01 M CaCl2 + 0.1 M TEA method and the six biological indices were 0.621**, 0.823**, 0.810** 0.433**, 0.558**, and 0.640**, respectively. For the 0.005 M DTPA + 1 M NH4HCO3 method, these coefficients were equal to 0.618**, 0.520**, 0.679**, 0.521**, 0.492**, and 0.641**, respectively (** indicate the validity of the relationships at p < 0.01) These extraction methods, out of all the methods tested, were suggested for the determination of the available Fe content of the brown forest soils.

  4. An efficient iterative grand canonical Monte Carlo algorithm to determine individual ionic chemical potentials in electrolytes.

    Science.gov (United States)

    Malasics, Attila; Boda, Dezso

    2010-06-28

    Two iterative procedures have been proposed recently to calculate the chemical potentials corresponding to prescribed concentrations from grand canonical Monte Carlo (GCMC) simulations. Both are based on repeated GCMC simulations with updated excess chemical potentials until the desired concentrations are established. In this paper, we propose combining our robust and fast converging iteration algorithm [Malasics, Gillespie, and Boda, J. Chem. Phys. 128, 124102 (2008)] with the suggestion of Lamperski [Mol. Simul. 33, 1193 (2007)] to average the chemical potentials in the iterations (instead of just using the chemical potentials obtained in the last iteration). We apply the unified method for various electrolyte solutions and show that our algorithm is more efficient if we use the averaging procedure. We discuss the convergence problems arising from violation of charge neutrality when inserting/deleting individual ions instead of neutral groups of ions (salts). We suggest a correction term to the iteration procedure that makes the algorithm efficient to determine the chemical potentials of individual ions too.

  5. Determination of the Rate Coefficients of the SO2 plus O plus M yields SO3 plus M Reaction

    Science.gov (United States)

    Hwang, S. M.; Cooke, J. A.; De Witt, K. J.; Rabinowitz, M. J.

    2010-01-01

    Rate coefficients of the title reaction R(sub 31) (SO2 +O+M yields SO3 +M) and R(sub 56) (SO2 + HO2 yields SO3 +OH), important in the conversion of S(IV) to S(VI),were obtained at T =970-1150 K and rho (sub ave) = 16.2 micro mol/cubic cm behind reflected shock waves by a perturbation method. Shock-heated H2/ O2/Ar mixtures were perturbed by adding small amounts of SO2 (1%, 2%, and 3%) and the OH temporal profiles were then measured using laser absorption spectroscopy. Reaction rate coefficients were elucidated by matching the characteristic reaction times acquired from the individual experimental absorption profiles via simultaneous optimization of k(sub 31) and k(sub 56) values in the reaction modeling (for satisfactory matches to the observed characteristic times, it was necessary to take into account R(sub 56)). In the experimental conditions of this study, R(sub 31) is in the low-pressure limit. The rate coefficient expressions fitted using the combined data of this study and the previous experimental results are k(sub 31,0)/[Ar] = 2.9 10(exp 35) T(exp ?6.0) exp(?4780 K/T ) + 6.1 10(exp 24) T(exp ?3.0) exp(?1980 K/T ) cm(sup 6) mol(exp ?2)/ s at T = 300-2500 K; k(sub 56) = 1.36 10(exp 11) exp(?3420 K/T ) cm(exp 3)/mol/s at T = 970-1150 K. Computer simulations of typical aircraft engine environments, using the reaction mechanism with the above k(sub 31,0) and k(sub 56) expressions, gave the maximum S(IV) to S(VI) conversion yield of ca. 3.5% and 2.5% for the constant density and constant pressure flow condition, respectively. Moreover, maximum conversions occur at rather higher temperatures (?1200 K) than that where the maximum k(sub 31,0) value is located (approximately 800 K). This is because the conversion yield is dependent upon not only the k(sup 31,0) and k(sup 56) values (production flux) but also the availability of H, O, and HO2 in the system (consumption flux).

  6. A laboratory manual for the determination of inorganic chemical contaminants and nutrients in sewage sludges

    International Nuclear Information System (INIS)

    Smith, R.

    1984-01-01

    In addition to a brief discussion on sewage sludge disposal, sludge contaminants, and the potential beneficial and adverse effects of the various inorganic chemical contaminants and nutrients commonly present in sewage sludge, this technical guide presents a scheme of analysis for the determination of the major inorganic contaminants and nutrients. Safety and simplicity were the main criteria considered in the selection of the various sample pretreatment procedures and analytical techniques

  7. Radioimmunoassay and chemical ionization/mass spectrometry compared for plasma cortisol determination

    International Nuclear Information System (INIS)

    Lindberg, C.; Johnson, S.; Hedner, P.; Gustafsson, A.

    1982-01-01

    A method is described for determination of cortisol in plasma and urine, based on chemical ionization/mass spectrometry with deuterium-labeled cortisol as the internal standard. The within-run precision (CV) was 2.5-5.7%, the between-run precision 4.6%. Results by this method were compared with those by a radioimmunological method (RIANEN Cortisol, New England Nuclear) for 395 plasma samples. The latter method gave significantly higher (approx. 25%) cortisol values

  8. Determination of alpha-naphthol by an oscillating chemical reaction using the analyte pulse perturbation technique

    International Nuclear Information System (INIS)

    Yang Wu; Sun Kanjun; Lv Weilian; Bo Lili; He Xiaoyan; Suo Nan; Gao Jinzhang

    2005-01-01

    An analytical method for the determination of alpha-naphthol (α-NP) is proposed by the sequential perturbation caused by different amounts of alpha-naphthol on the oscillating chemical system involving the Cu(II)-catalyzed oscillating reaction between hydrogen peroxide and sodium thiocyanate in an alkaline medium with the aid of continuous-flow stirred tank reactor (CSTR). The method relies on the linear relationship between the changes in the oscillation amplitude of the chemical system and the concentration of alpha-naphthol. The use of the analyte pulse perturbation technique permits sequential determinations in the same oscillating system owing to the expeditiousness with which the steady state is regained after each perturbation. The calibration curve obeys a linear equation very well when the concentration of alpha-naphthol is over the range 0.034-530 umol/L (r = 0.9991). Influences of temperature, injection points, flow rate and reaction variables on the oscillating system are investigated in detail and the possible mechanism of action of alpha-naphthol to the chemical oscillating system is also discussed. The method has been successfully used for the determination of α-naphthol in carbaryl hydrolysates

  9. Formation and Yield of Multi-Walled Carbon Nanotubes Synthesized via Chemical Vapour Deposition Routes Using Different Metal-Based Catalysts of FeCoNiAl, CoNiAl and FeNiAl-LDH

    Directory of Open Access Journals (Sweden)

    Mohd Zobir Hussein

    2014-11-01

    Full Text Available Multi-walled carbon nanotubes (MWCNTs were prepared via chemical vapor deposition (CVD using a series of different catalysts, derived from FeCoNiAl, CoNiAl and FeNiAl layered double hydroxides (LDHs. Catalyst-active particles were obtained by calcination of LDHs at 800 °C for 5 h. Nitrogen and hexane were used as the carrier gas and carbon source respectively, for preparation of MWCNTs using CVD methods at 800 °C. MWCNTs were allowed to grow for 30 min on the catalyst spread on an alumina boat in a quartz tube. The materials were subsequently characterized through X-ray diffraction, Fourier transform infrared spectroscopy, surface area analysis, field emission scanning electron microscopy and transmission electron microscopy. It was determined that size and yield of MWCNTs varied depending on the type of LDH catalyst precursor that is used during synthesis. MWCNTs obtained using CoNiAl-LDH as the catalyst precursor showed smaller diameter and higher yield compared to FeCoNiAl and FeNiAl LDHs.

  10. Determination of sulfonamides in meat by liquid chromatography coupled with atmospheric pressure chemical ionization mass spectrometry

    International Nuclear Information System (INIS)

    Kim, Dal Ho; Choi, Jong Oh; Kim, Jin Seog; Lee, Dai Woon

    2002-01-01

    Liquid chromatography/atmospheric pressure chemical ionization-mass spectrometry (LC-APCI-MS) has been used for the determination of sulfonamides in meat. Five typical sulfonamides were selected as target compounds, and beef meat was selected as a matrix sample. As internal standards, sulfapyridine and isotope labeled sulfamethazine ( 13 C 6 -SMZ) were used. Compared to the results of recent reports, our results have shown improved precision to a RSD of 1.8% for the determination of sulfamethazine spiked with 75 ng/g level in meat

  11. New method to enhance the extraction yield of rutin from Sophora japonica using a novel ultrasonic extraction system by determining optimum ultrasonic frequency.

    Science.gov (United States)

    Liao, Jianqing; Qu, Baida; Liu, Da; Zheng, Naiqin

    2015-11-01

    A new method has been proposed for enhancing extraction yield of rutin from Sophora japonica, in which a novel ultrasonic extraction system has been developed to perform the determination of optimum ultrasonic frequency by a two-step procedure. This study has systematically investigated the influence of a continuous frequency range of 20-92 kHz on rutin yields. The effects of different operating conditions on rutin yields have also been studied in detail such as solvent concentration, solvent to solid ratio, ultrasound power, temperature and particle size. A higher extraction yield was obtained at the ultrasonic frequency of 60-62 kHz which was little affected under other extraction conditions. Comparative studies between existing methods and the present method were done to verify the effectiveness of this method. Results indicated that the new extraction method gave a higher extraction yield compared with existing ultrasound-assisted extraction (UAE) and soxhlet extraction (SE). Thus, the potential use of this method may be promising for extraction of natural materials on an industrial scale in the future. Copyright © 2015 Elsevier B.V. All rights reserved.

  12. Evaluation of scission and crosslinking yields in γ-irradiated poly(acrylic acid) and poly(methacrylic acid) from weight- and Ζ-average molecular weights determined by sedimentation equilibrium

    International Nuclear Information System (INIS)

    Hill, D.J.T.; O'Donnell, J.H.; Winzor, C.L.; Winzor, D.J.

    1990-01-01

    Weight- and Ζ-average molecular weights, M-bar W (D) and M-bar Ζ (D), of poly(methacrylic acid) (PMMA) and poly(acrylic acid) (PAA) have been determined by sedimentation equilibrium in the ultracentrifuge after various doses D of γ-radiation in vacuum. Relationships between [M i (0)/M i (D)-1]/D and D (i=w or Ζ), derived recently by O'Donnell and coworkers, have been used to determine radiation chemical yields for scission and crosslinking of G(S)=6.0, G(X)=0 for PMAA and G(S)=0, G(X)=0.44 for PAA. Allowance was necessary for the effects of COOH decomposition on the average values of the molecular weight and partial specific volume for irradiated PAA. (author)

  13. ACC oxidase and miRNA 159a, and their involvement in fresh fruit bunch yield (FFB) via sex ratio determination in oil palm.

    Science.gov (United States)

    Somyong, Suthasinee; Poopear, Supannee; Sunner, Supreet Kaur; Wanlayaporn, Kitti; Jomchai, Nukoon; Yoocha, Thippawan; Ukoskit, Kittipat; Tangphatsornruang, Sithichoke; Tragoonrung, Somvong

    2016-06-01

    Oil palm (Elaeis guineesis Jacq.) is the most productive oil-bearing crop, yielding more oil per area than any other oil-bearing crops. However, there are still efforts to improve oil palm yield, in order to serve consumer and manufacturer demand. Oil palm produces female and male inflorescences in an alternating cycle. So, high sex ratio (SR), the ratio of female inflorescences to the total inflorescences, is a favorable trait in term of increasing yields in oil palm. This study aims to understand the genetic control for SR related traits, such as fresh fruit bunch yield (FFB), by characterizing genes at FFB quantitative trait loci (QTLs) on linkage 10 (chromosome 6) and linkage 15 (chromosome 10). Published oil palm sequences at the FFB QTLs were used to develop gene-based and simple sequence repeat (SSR) markers. We used the multiple QTL analysis model (MQM) to characterize the relationship of new markers with the SR traits in the oil palm population. The RNA expression of the most linked QTL genes was also evaluated in various tissues of oil palm. We identified EgACCO1 (encoding aminocyclopropane carboxylate (ACC) oxidase) at chromosome 10 and EgmiR159a (microRNA 159a) at chromosome 6 to be the most linked QTL genes or determinants for FFB yield and/or female inflorescence number with a phenotype variance explained (PVE) from 10.4 to 15 % and suggest that these play the important roles in sex determination and differentiation in oil palm. The strongest expression of EgACCO1 and the predicted precursor of EgmiR159a was found in ovaries and, to a lesser extent, fruit development. In addition, highly normalized expression of EgmiR159a was found in female flowers. In summary, the QTL analysis and the RNA expression reveal that EgACCO1 and EgmiR159a are the potential genetic factors involved in female flower determination and hence would affect yield in oil palm. However, to clarify how these genetic factors regulate female flower determination, more investigation

  14. EDXRF applied to the chemical element determination of small invertebrate samples

    International Nuclear Information System (INIS)

    Magalhaes, Marcelo L.R.; Santos, Mariana L.O.; Cantinha, Rebeca S.; Souza, Thomas Marques de; Franca, Elvis J. de

    2015-01-01

    Energy Dispersion X-Ray Fluorescence - EDXRF is a fast analytical technique of easy operation, however demanding reliable analytical curves due to the intrinsic matrix dependence and interference during the analysis. By using biological materials of diverse matrices, multielemental analytical protocols can be implemented and a group of chemical elements could be determined in diverse biological matrices depending on the chemical element concentration. Particularly for invertebrates, EDXRF presents some advantages associated to the possibility of the analysis of small size samples, in which a collimator can be used that directing the incidence of X-rays to a small surface of the analyzed samples. In this work, EDXRF was applied to determine Cl, Fe, P, S and Zn in invertebrate samples using the collimator of 3 mm and 10 mm. For the assessment of the analytical protocol, the SRM 2976 Trace Elements in Mollusk produced and SRM 8415 Whole Egg Powder by the National Institute of Standards and Technology - NIST were also analyzed. After sampling by using pitfall traps, invertebrate were lyophilized, milled and transferred to polyethylene vials covered by XRF polyethylene. Analyses were performed at atmosphere lower than 30 Pa, varying voltage and electric current according to the chemical element to be analyzed. For comparison, Zn in the invertebrate material was also quantified by graphite furnace atomic absorption spectrometry after acid treatment (mixture of nitric acid and hydrogen peroxide) of samples have. Compared to the collimator of 10 mm, the SRM 2976 and SRM 8415 results obtained by the 3 mm collimator agreed well at the 95% confidence level since the E n Number were in the range of -1 and 1. Results from GFAAS were in accordance to the EDXRF values for composite samples. Therefore, determination of some chemical elements by EDXRF can be recommended for very small invertebrate samples (lower than 100 mg) with advantage of preserving the samples. (author)

  15. EDXRF applied to the chemical element determination of small invertebrate samples

    Energy Technology Data Exchange (ETDEWEB)

    Magalhaes, Marcelo L.R.; Santos, Mariana L.O.; Cantinha, Rebeca S.; Souza, Thomas Marques de; Franca, Elvis J. de, E-mail: marcelo_rlm@hotmail.com, E-mail: marianasantos_ufpe@hotmail.com, E-mail: rebecanuclear@gmail.com, E-mail: thomasmarques@live.com.pt, E-mail: ejfranca@cnen.gov.br [Centro Regional de Ciencias Nucleares do Nordeste (CRCN-NE/CNEN-PE), Recife, PE (Brazil)

    2015-07-01

    Energy Dispersion X-Ray Fluorescence - EDXRF is a fast analytical technique of easy operation, however demanding reliable analytical curves due to the intrinsic matrix dependence and interference during the analysis. By using biological materials of diverse matrices, multielemental analytical protocols can be implemented and a group of chemical elements could be determined in diverse biological matrices depending on the chemical element concentration. Particularly for invertebrates, EDXRF presents some advantages associated to the possibility of the analysis of small size samples, in which a collimator can be used that directing the incidence of X-rays to a small surface of the analyzed samples. In this work, EDXRF was applied to determine Cl, Fe, P, S and Zn in invertebrate samples using the collimator of 3 mm and 10 mm. For the assessment of the analytical protocol, the SRM 2976 Trace Elements in Mollusk produced and SRM 8415 Whole Egg Powder by the National Institute of Standards and Technology - NIST were also analyzed. After sampling by using pitfall traps, invertebrate were lyophilized, milled and transferred to polyethylene vials covered by XRF polyethylene. Analyses were performed at atmosphere lower than 30 Pa, varying voltage and electric current according to the chemical element to be analyzed. For comparison, Zn in the invertebrate material was also quantified by graphite furnace atomic absorption spectrometry after acid treatment (mixture of nitric acid and hydrogen peroxide) of samples have. Compared to the collimator of 10 mm, the SRM 2976 and SRM 8415 results obtained by the 3 mm collimator agreed well at the 95% confidence level since the E{sub n} Number were in the range of -1 and 1. Results from GFAAS were in accordance to the EDXRF values for composite samples. Therefore, determination of some chemical elements by EDXRF can be recommended for very small invertebrate samples (lower than 100 mg) with advantage of preserving the samples. (author)

  16. Study of the Relationships between Technological and Productivity Elements that Determine Seed Yield in Birdsfoot Trefoil (Lotus Corniculatus L.

    Directory of Open Access Journals (Sweden)

    Neculai Dragomir

    2011-10-01

    Full Text Available During an experience performed to elaborate an efficient technology of seed production in birdsfoot trefoil, we observed a series of correlations between yield and the elements of productivity, which exert a strong influence on seed quantity. In this viewpoint, the matrix of correlations between the elements of fructification, in the case of the influence exerted by birdsfoot trefoil cultivation method, made evident the following correlation coefficients: r = 0.81**, between the number of pods/plant; r = 0.82**, between the number of generative sprigs and the number of pods/inflorescence; r = 0.98**, between the number of generative sprigs and the number of pods/plant.

  17. H + CH{sub 2}CO {yields} CH{sub 3} + CO at high temperature : a high pressure chemical activation reaction with positive barrier.

    Energy Technology Data Exchange (ETDEWEB)

    Hranisavljevic, J.; Kumaran, S. S.; Michael, J. V.

    1997-12-08

    The Laser Photolysis-Shock Tube (LP-ST) technique coupled with H-atom atomic resonance absorption spectrometry (ARAS) has been used to study reaction, H + CH{sub 2}CO {r_arrow} CH{sub 3} + CO, over the temperature range, 863-1400 K. The results can be represented by the Arrhenius expression, k = (4.85 {+-} 0.70) x 10{sup {minus}11} exp({minus}2328 {+-} 155 K/T) cm{sup 3} molecule{sup {minus}1} s{sup {minus}1}. The present data have been combined with the earlier low temperature flash photolysis-resonance fluorescence measurements to yield a joint three parameter expression, k = 5.44 x 10{sup {minus}14} T{sup 0.8513} exp({minus}1429 K/T) cm{sup 3} molecule{sup {minus}1} s{sup {minus}1}. This is a chemical activation process that proceeds through vibrationally excited acetyl radicals. However, due to the presence of a low lying forward dissociation channel to CH{sub 3} + CO, the present results refer to the high pressure limiting rate constants. Hence, transition state theory with Eckart tunneling is used to explain the data.

  18. Chemical aspects of the precise and accurate determination of uranium and plutonium from nuclear fuel solutions

    International Nuclear Information System (INIS)

    Heinonen, O.J.

    1981-01-01

    A method for the simultaneous or separate determination of uranium and plutonium has been developed. The method is based on the sorption of uranium and plutonium as their chloro complexes on Dowex 1x10 column. When separate uranium and plutonium fractions are desired, plutonium ions are reduced to Pu (III) and eluted, after which the uranium ions are eluted with dilute HCl. Simultaneous stripping of a mass ratio U/Pu approximately 1 fraction for mass spectrometric measurements is achieved by proper choice of eluant HC1 concentration. Special attention was paid to the obtaining of americium free plutonium fractions. The distribution coefficient measurements showed that at 12.5-M HCl at least 30 % of americium ions formed anionic chloro complexes. The chemical aspects of isotopic fractionation in a multiple filament thermal ionization source were also investigated. Samples of uranium were loaded as nitrates, chlorides, and sulphates and the dependence of the measured uranium isotopic ratios on the chemical form of the loading solution as well as on the filament material was studied. Likewise the dependence of the formation of uranium and its oxide ions on various chemical and instrumental conditions was investigated using tungsten and rhenium filaments. Systematic errors arising from the chemical conditions are compared with errors arising from the automatic evaluation of of spectra. (author)

  19. Determinants of job stress in chemical process industry: A factor analysis approach.

    Science.gov (United States)

    Menon, Balagopal G; Praveensal, C J; Madhu, G

    2015-01-01

    Job stress is one of the active research domains in industrial safety research. The job stress can result in accidents and health related issues in workers in chemical process industries. Hence it is important to measure the level of job stress in workers so as to mitigate the same to avoid the worker's safety related problems in the industries. The objective of this study is to determine the job stress factors in the chemical process industry in Kerala state, India. This study also aims to propose a comprehensive model and an instrument framework for measuring job stress levels in the chemical process industries in Kerala, India. The data is collected through a questionnaire survey conducted in chemical process industries in Kerala. The collected data out of 1197 surveys is subjected to principal component and confirmatory factor analysis to develop the job stress factor structure. The factor analysis revealed 8 factors that influence the job stress in process industries. It is also found that the job stress in employees is most influenced by role ambiguity and the least by work environment. The study has developed an instrument framework towards measuring job stress utilizing exploratory factor analysis and structural equation modeling.

  20. Accuracy and precision of protein-ligand interaction kinetics determined from chemical shift titrations

    Energy Technology Data Exchange (ETDEWEB)

    Markin, Craig J.; Spyracopoulos, Leo, E-mail: leo.spyracopoulos@ualberta.ca [University of Alberta, Department of Biochemistry (Canada)

    2012-12-15

    NMR-monitored chemical shift titrations for the study of weak protein-ligand interactions represent a rich source of information regarding thermodynamic parameters such as dissociation constants (K{sub D}) in the micro- to millimolar range, populations for the free and ligand-bound states, and the kinetics of interconversion between states, which are typically within the fast exchange regime on the NMR timescale. We recently developed two chemical shift titration methods wherein co-variation of the total protein and ligand concentrations gives increased precision for the K{sub D} value of a 1:1 protein-ligand interaction (Markin and Spyracopoulos in J Biomol NMR 53: 125-138, 2012). In this study, we demonstrate that classical line shape analysis applied to a single set of {sup 1}H-{sup 15}N 2D HSQC NMR spectra acquired using precise protein-ligand chemical shift titration methods we developed, produces accurate and precise kinetic parameters such as the off-rate (k{sub off}). For experimentally determined kinetics in the fast exchange regime on the NMR timescale, k{sub off} {approx} 3,000 s{sup -1} in this work, the accuracy of classical line shape analysis was determined to be better than 5 % by conducting quantum mechanical NMR simulations of the chemical shift titration methods with the magnetic resonance toolkit GAMMA. Using Monte Carlo simulations, the experimental precision for k{sub off} from line shape analysis of NMR spectra was determined to be 13 %, in agreement with the theoretical precision of 12 % from line shape analysis of the GAMMA simulations in the presence of noise and protein concentration errors. In addition, GAMMA simulations were employed to demonstrate that line shape analysis has the potential to provide reasonably accurate and precise k{sub off} values over a wide range, from 100 to 15,000 s{sup -1}. The validity of line shape analysis for k{sub off} values approaching intermediate exchange ({approx}100 s{sup -1}), may be facilitated by

  1. Accuracy and precision of protein–ligand interaction kinetics determined from chemical shift titrations

    International Nuclear Information System (INIS)

    Markin, Craig J.; Spyracopoulos, Leo

    2012-01-01

    NMR-monitored chemical shift titrations for the study of weak protein–ligand interactions represent a rich source of information regarding thermodynamic parameters such as dissociation constants (K D ) in the micro- to millimolar range, populations for the free and ligand-bound states, and the kinetics of interconversion between states, which are typically within the fast exchange regime on the NMR timescale. We recently developed two chemical shift titration methods wherein co-variation of the total protein and ligand concentrations gives increased precision for the K D value of a 1:1 protein–ligand interaction (Markin and Spyracopoulos in J Biomol NMR 53: 125–138, 2012). In this study, we demonstrate that classical line shape analysis applied to a single set of 1 H– 15 N 2D HSQC NMR spectra acquired using precise protein–ligand chemical shift titration methods we developed, produces accurate and precise kinetic parameters such as the off-rate (k off ). For experimentally determined kinetics in the fast exchange regime on the NMR timescale, k off ∼ 3,000 s −1 in this work, the accuracy of classical line shape analysis was determined to be better than 5 % by conducting quantum mechanical NMR simulations of the chemical shift titration methods with the magnetic resonance toolkit GAMMA. Using Monte Carlo simulations, the experimental precision for k off from line shape analysis of NMR spectra was determined to be 13 %, in agreement with the theoretical precision of 12 % from line shape analysis of the GAMMA simulations in the presence of noise and protein concentration errors. In addition, GAMMA simulations were employed to demonstrate that line shape analysis has the potential to provide reasonably accurate and precise k off values over a wide range, from 100 to 15,000 s −1 . The validity of line shape analysis for k off values approaching intermediate exchange (∼100 s −1 ), may be facilitated by more accurate K D measurements from NMR

  2. Accuracy and precision of protein-ligand interaction kinetics determined from chemical shift titrations.

    Science.gov (United States)

    Markin, Craig J; Spyracopoulos, Leo

    2012-12-01

    NMR-monitored chemical shift titrations for the study of weak protein-ligand interactions represent a rich source of information regarding thermodynamic parameters such as dissociation constants (K ( D )) in the micro- to millimolar range, populations for the free and ligand-bound states, and the kinetics of interconversion between states, which are typically within the fast exchange regime on the NMR timescale. We recently developed two chemical shift titration methods wherein co-variation of the total protein and ligand concentrations gives increased precision for the K ( D ) value of a 1:1 protein-ligand interaction (Markin and Spyracopoulos in J Biomol NMR 53: 125-138, 2012). In this study, we demonstrate that classical line shape analysis applied to a single set of (1)H-(15)N 2D HSQC NMR spectra acquired using precise protein-ligand chemical shift titration methods we developed, produces accurate and precise kinetic parameters such as the off-rate (k ( off )). For experimentally determined kinetics in the fast exchange regime on the NMR timescale, k ( off ) ~ 3,000 s(-1) in this work, the accuracy of classical line shape analysis was determined to be better than 5 % by conducting quantum mechanical NMR simulations of the chemical shift titration methods with the magnetic resonance toolkit GAMMA. Using Monte Carlo simulations, the experimental precision for k ( off ) from line shape analysis of NMR spectra was determined to be 13 %, in agreement with the theoretical precision of 12 % from line shape analysis of the GAMMA simulations in the presence of noise and protein concentration errors. In addition, GAMMA simulations were employed to demonstrate that line shape analysis has the potential to provide reasonably accurate and precise k ( off ) values over a wide range, from 100 to 15,000 s(-1). The validity of line shape analysis for k ( off ) values approaching intermediate exchange (~100 s(-1)), may be facilitated by more accurate K ( D ) measurements

  3. Alternative Bio-Based Solvents for Extraction of Fat and Oils: Solubility Prediction, Global Yield, Extraction Kinetics, Chemical Composition and Cost of Manufacturing

    Directory of Open Access Journals (Sweden)

    Anne-Gaëlle Sicaire

    2015-04-01

    Full Text Available The present study was designed to evaluate the performance of alternative bio-based solvents, more especially 2-methyltetrahydrofuran, obtained from crop’s byproducts for the substitution of petroleum solvents such as hexane in the extraction of fat and oils for food (edible oil and non-food (bio fuel applications. First a solvent selection as well as an evaluation of the performance was made with Hansen Solubility Parameters and the COnductor-like Screening MOdel for Realistic Solvation (COSMO-RS simulations. Experiments were performed on rapeseed oil extraction at laboratory and pilot plant scale for the determination of lipid yields, extraction kinetics, diffusion modeling, and complete lipid composition in term of fatty acids and micronutrients (sterols, tocopherols and tocotrienols. Finally, economic and energetic evaluations of the process were conducted to estimate the cost of manufacturing using 2-methyltetrahydrofuran (MeTHF as alternative solvent compared to hexane as petroleum solvent.

  4. Equity yields

    NARCIS (Netherlands)

    Vrugt, E.; van Binsbergen, J.H.; Koijen, R.S.J.; Hueskes, W.

    2013-01-01

    We study a new data set of dividend futures with maturities up to ten years across three world regions: the US, Europe, and Japan. We use these asset prices to construct equity yields, analogous to bond yields. We decompose the equity yields to obtain a term structure of expected dividend growth

  5. Determination of chemical composition, total phenolic content and antioxidant activity of xylanthemum macropodum

    International Nuclear Information System (INIS)

    Samiullah, A.; Tareen, R.B.; Khan, N.; Akber, A.; Ali, I.; Khan, A.K.

    2017-01-01

    Evaluation of the phytochemistry, total phenolic content and antioxidant activity of the endemic plant of northern Balochistan Xylanthemum Macropodum of the Asteraceae family, is reported for the first time in this document. Chemical composition of Xylanthemum Macropodum was determined using well-established chemical tests and modern spectroscopic techniques. Extracts were taken from the whole plant using methanol and the extracts were tested for phytochemicals (secondary metabolites), total phenolic content (TPC) and antioxidant activity. The phytochemical (biochemical) examination of Xylanthemum Macropodum exposed the presence of alkaloids, phenols, steroids, flavonoids, tannins, terpenoids, saponins, coumarins, carbohydrates, cardiac glycosides, reducing sugars, and quinines. TPC of crude methanolic extract (CME) of plant was determined using Folin-Ciocalteu's reagent. The TPC determined was 256mg of tannic acid Eq/g of extract. Antioxidant activities were determined spectrophotometrically using the DPPH assay and Ferric ion (Fe/sup +3/) reducing antioxidant power assay. The potency of the DPPH assay of Xylanthemum Macropodum extract was 68% for the 0.10 mg/ml concentration and the FRAP value of the extract was 3.368 mmol Fe/sup +2//g of extract. Xylanthemum Macropodum has proved to be very rich in secondary metabolites, natural phenolics and has a very potent antioxidant activity. (author)

  6. Determination of 233U, 235U, 238U and 239Pu fission yields induced by fission and 14.7 MeV neutrons

    International Nuclear Information System (INIS)

    Laurec, Jean; Adam, Albert; Bruyne, Thierry de.

    1981-12-01

    The 233 U, 235 U, 238 U, 239 Pu fission yields have been determined by a radiochemical method. A target and a fission chamber made of same fissible material are irradied together. The total fission number is measured from the fission chamber. The fission product activities are directly measured on the target using calibrated Ge-Li detectors. The fissible material masses are determined by alpha and mass spectrometries. The irradiations were made on the critical assemblies PROSPERO and CALIBAN and on the 14 MeV neutron generator of C.E. VALDUC. 3 to 5% fission yield errors are got for the most measured nuclides: 95 Zr, 97 Zr, 99 Mo, 103 Ru, 131 I, 132 Te, 140 Ba, 141 Ce, 143 Ce, 144 Ce, 147 Nd [fr

  7. CHEMICALS

    CERN Multimedia

    Medical Service

    2002-01-01

    It is reminded that all persons who use chemicals must inform CERN's Chemistry Service (TIS-GS-GC) and the CERN Medical Service (TIS-ME). Information concerning their toxicity or other hazards as well as the necessary individual and collective protection measures will be provided by these two services. Users must be in possession of a material safety data sheet (MSDS) for each chemical used. These can be obtained by one of several means : the manufacturer of the chemical (legally obliged to supply an MSDS for each chemical delivered) ; CERN's Chemistry Service of the General Safety Group of TIS ; for chemicals and gases available in the CERN Stores the MSDS has been made available via EDH either in pdf format or else via a link to the supplier's web site. Training courses in chemical safety are available for registration via HR-TD. CERN Medical Service : TIS-ME :73186 or service.medical@cern.ch Chemistry Service : TIS-GS-GC : 78546

  8. Determination of the thickness of chemically removed thin layers on GaAs VPE structures

    Energy Technology Data Exchange (ETDEWEB)

    Somogyi, K.; Nemeth-Sallay, M.; Nemcsics, A. (Research Inst. for Technical Physics, Hungarian Academy of Sciences, Budapest (Hungary))

    1991-01-01

    Thinning of epitaxial GaAs layers was studied during the surface etching, with a special attention to submicron epitaxial structures, like MESFET or varactor-type structures. Each chemical treatment influences the crystal surface during the device preparation processes, though the possible thinning of the active layer is small. Therefore a method allowing determination of thicknesses as small as at about 20 nm of the layer removed by chemical etching from GaAs VPE structures was applied. Using special multilayered structures and a continuous electrochemical carrier concentration depth profiling, the influence of the layer thickness inhomogeneity and of some measurement errors can be minimized. Some frequently used etchants and the influence of different - so called - non-etching processes were compared in different combinations. It was shown that besides the direct etching a change of the surface conditions occurs, which influences the etch rate in the succeeding etching procedure. (orig.).

  9. Determination of renewable energy yield from mixed waste material from the use of novel image analysis methods.

    Science.gov (United States)

    Wagland, S T; Dudley, R; Naftaly, M; Longhurst, P J

    2013-11-01

    Two novel techniques are presented in this study which together aim to provide a system able to determine the renewable energy potential of mixed waste materials. An image analysis tool was applied to two waste samples prepared using known quantities of source-segregated recyclable materials. The technique was used to determine the composition of the wastes, where through the use of waste component properties the biogenic content of the samples was calculated. The percentage renewable energy determined by image analysis for each sample was accurate to within 5% of the actual values calculated. Microwave-based multiple-point imaging (AutoHarvest) was used to demonstrate the ability of such a technique to determine the moisture content of mixed samples. This proof-of-concept experiment was shown to produce moisture measurement accurate to within 10%. Overall, the image analysis tool was able to determine the renewable energy potential of the mixed samples, and the AutoHarvest should enable the net calorific value calculations through the provision of moisture content measurements. The proposed system is suitable for combustion facilities, and enables the operator to understand the renewable energy potential of the waste prior to combustion. Copyright © 2013 Elsevier Ltd. All rights reserved.

  10. Determination of vanadium in mussels by electrothermal atomic absorption spectrometry without chemical modifiers

    Energy Technology Data Exchange (ETDEWEB)

    Saavedra, Y.; Fernandez, P. [Centro de Control do Medio Marino, Peirao de Vilaxoan s/n, Vilagarcia de Arousa, 36611 Pontevedra (Spain); Gonzalez, A. [Departamento de Quimica Analitica, Nutricion y Bromatologia, Facultad de Quimica, 15706, Santiago de Compostela (Spain)

    2004-05-01

    A method was developed for the quantitative determination of total vanadium concentration in mussels via electrothermal atomic absorption spectrometry (ETAAS). After the microwave digestion of the samples, a program using temperatures of 1600 C and 2600 C for ashing and atomization respectively, without any matrix modifiers, allowed us to obtain results that were satisfactory since they agreed closely with certified reference material values. The detection limit was 0.03 mg kg{sup -1} (dry weight), indicating that the method is suitable for the analysis of mussel samples. This determination was compared with matrix modifiers that have been reported previously. The method was applied to various cultivated and wild mussels from the Galician coast, yielding levels below 1 mg kg{sup -1} (wet weight). (orig.)

  11. Rapid determination of chemical composition and classification of bamboo fractions using visible-near infrared spectroscopy coupled with multivariate data analysis.

    Science.gov (United States)

    Yang, Zhong; Li, Kang; Zhang, Maomao; Xin, Donglin; Zhang, Junhua

    2016-01-01

    During conversion of bamboo into biofuels and chemicals, it is necessary to efficiently predict the chemical composition and digestibility of biomass. However, traditional methods for determination of lignocellulosic biomass composition are expensive and time consuming. In this work, a novel and fast method for quantitative and qualitative analysis of chemical composition and enzymatic digestibilities of juvenile bamboo and mature bamboo fractions (bamboo green, bamboo timber, bamboo yellow, bamboo node, and bamboo branch) using visible-near infrared spectra was evaluated. The developed partial least squares models yielded coefficients of determination in calibration of 0.88, 0.94, and 0.96, for cellulose, xylan, and lignin of bamboo fractions in raw spectra, respectively. After visible-near infrared spectra being pretreated, the corresponding coefficients of determination in calibration yielded by the developed partial least squares models are 0.994, 0.990, and 0.996, respectively. The score plots of principal component analysis of mature bamboo, juvenile bamboo, and different fractions of mature bamboo were obviously distinguished in raw spectra. Based on partial least squares discriminant analysis, the classification accuracies of mature bamboo, juvenile bamboo, and different fractions of bamboo (bamboo green, bamboo timber, bamboo yellow, and bamboo branch) all reached 100 %. In addition, high accuracies of evaluation of the enzymatic digestibilities of bamboo fractions after pretreatment with aqueous ammonia were also observed. The results showed the potential of visible-near infrared spectroscopy in combination with multivariate analysis in efficiently analyzing the chemical composition and hydrolysabilities of lignocellulosic biomass, such as bamboo fractions.

  12. Analytical applications of oscillatory chemical reactions: determination of some pharmaceuticaly and biologically important compounds

    Directory of Open Access Journals (Sweden)

    Pejić Nataša D.

    2012-01-01

    Full Text Available Novel analytical methods for quantitive determination of analytes based on perturbations of oscillatory chemical reactions realized under open reactor conditions (continuosly fed well stirred tank reactor, CSTR, have been developed in the past twenty years. The proposed kinetic methods are generally based on the ability of the analyzed substances to change the kinetics of the chemical reactions matrix. The unambiguous correlation of quantitative characteristics of perturbations, and the amount (concentration of analyte expressed as a regression equation, or its graphics (calibration curve, enable the determination of the unknown analyte concentration. Attention is given to the development of these methods because of their simple experimental procedures, broad range of linear regression ( 10-7 10-4 mol L-1 and low limits of detection of analytes ( 10-6 10-8 mol L1, in some cases even lower than 10-12 mol L-1. Therefore, their application is very convenient for routine analysis of various inorganic and organic compounds as well as gases. This review summarizes progress made in the past 5 years on quantitative determination of pharmaceutically and biologically important compounds.

  13. Radiometric sampling of bucked copper-nickel ores for determining chemical composition

    International Nuclear Information System (INIS)

    Komlev, V.N.; Eliseev, G.I.

    1978-01-01

    Presented are the results and the technique of experimental-methodical works on radiometric sampling of bucked copper-nickel ores for determining chemical composition with their selection and analysis by the neutron-gamma method and by the gamma-gamma method. The error is estimated according to the chosen conditions of sampling. It is found that the gamma-gamma method being more rapid but less accurate is applied for rapid control of ore current, whereas the neutron-gamma method is applied for quality control of ores extracted

  14. Determination of densities from chemical composition and X-Ray diffraction

    International Nuclear Information System (INIS)

    Azevedo, A.L.T. de

    1980-01-01

    X-ray diffraction method applied to retained austenite measurements gives volume per cent results, whereas the same kind of measurement made by Moessbauer Effect gives iron percentages. To compare both results one needs to convert the volume % to weight % or vice-versa. This necessitates, among other things, in determining the densities of the α and #betta# phases in the steel being studied. A method for calculating the densities, based on the application of the definition of density to just one unit cell, using X-ray diffraction and chemical results, are described. (Author) [pt

  15. Determination of hydration numbers of electrolytes from temperature dependence of PMR chemical shifts

    International Nuclear Information System (INIS)

    Subramanian, N.

    1979-01-01

    The method proposed by Malinowski et al. for the determination of effective hydration numbers (h) of electrolytes leads to a consistent incrrease in the observed values of 'h' with increase in solution concentration. An attempt is made to rationalize the experimental results by cosidering the simultaneous effects of temperature and concentration on the proton chemical shift. It is suggested that Malinowski's technique might yeld 'h' values very close to the true value for those ions for which there is a fortuitous cancellation of structure-making and structure-breaking properties. (Author) [pt

  16. Determination of the concentration profile of chemical elements in superheater pipes

    International Nuclear Information System (INIS)

    Aldape U, F.; Aspiazu F, J.

    1986-05-01

    This work has for object to determine the profile of concentration of chemical elements at trace level in a superheater pipe of Thermoelectric Plants using the X-ray emission spectroscopy technique induced by protons coming from the Accelerator of the Nuclear Center. In the X-ray detection, a Si Li detector was used. The technique was chosen because it allows a multielemental analysis, of high sensitivity and precision. The results can help to understand the problems that are had in the change of flexibility or of corrosion. This will be from utility to the Federal Electricity Commission (CFE). (Author)

  17. Biological and chemical tests of contaminated soils to determine bioavailability and environmentally acceptable endpoints (EAE)

    International Nuclear Information System (INIS)

    Montgomery, C.R.; Menzie, C.A.; Pauwells, S.J.

    1995-01-01

    The understanding of the concept of bioavailability of soil contaminants to receptors and its use in supporting the development of EAE is growing but still incomplete. Nonetheless, there is increased awareness of the importance of such data to determine acceptable cleanup levels and achieve timely site closures. This presentation discusses a framework for biological and chemical testing of contaminated soils developed as part of a Gas Research Institute (GRI) project entitled ''Environmentally Acceptable Endpoints in Soil Using a Risk Based Approach to Contaminated Site Management Based on Bioavailability of Chemicals in Soil.'' The presentation reviews the GRI program, and summarizes the findings of the biological and chemical testing section published in the GRI report. The three primary components of the presentation are: (1) defining the concept of bioavailability within the existing risk assessment paradigm, (2) assessing the usefulness of the existing tests to measure bioavailability and test frameworks used to interpret these measurements, and (3) suggesting how a small selection of relevant tests could be incorporated into a flexible testing scheme for soils to address this issue

  18. Depth distribution of chemical phase concentration determined by grazing incidence X-ray diffraction

    International Nuclear Information System (INIS)

    Novak, P.; Ballo, P.; Dobrocka, E.; Vallo, M.; Lalinsky, T.

    2013-01-01

    Grazing incidence geometry is widely used in X-ray diffraction analysis of thin films. Penetration depth of radiation can be easily changed by an appropriate selection of the angle of incidence α that enables obtaining information from different depths of the sample. This depth can be decreased up to a nanometer scale by approaching the critical angle α_c for total external reflection. This method therefore provides an efficient tool for the analysis of depth distribution of various structural properties, such as the crystallite size, the amorphous fraction, stress or the concentration of chemical phase. However, absorption of the radiation can be characterized by an average attenuation coefficient μ a special care has to be paid to the last property. Variation of chemical phase concentration with depth usually results in depth dependence on the attenuation coefficient. In this contribution a method for determination of depth distribution of a chemical phase is outlined. The method correctly takes into account the depth variation of the attenuation coefficient. The method is tested on thin oxidized Ir layers. The aim of this paper is a comparison two simple model cases with the experimental results. (authors)

  19. Determination of {sup 2}30Th (Ionium) in uranium ores and wastes from uranium reprocessing. IV. Calculation of ionium separation yield; Determinacion de {sup 2}39Th (Ionio) en minerales y residuos del procesado de Uranio. IV: Determinacion del rendimiento en la separacion del {sup 2}30 Th

    Energy Technology Data Exchange (ETDEWEB)

    Galiano Sedano, J A; Acena Barrenechea, M L

    1974-07-01

    For determining ionium ({sup 2}30Th) in minerals and uranium processing wastes by precipitation with fluorhidric acid, using lanthanum as carrier, and selective extraction with tenoytrifluoroacetone (TTA) followed by radiometric determination of the isolated nuclide, it is necessary the use of a tracer since the chemical yield of the separation ranges between wide limits. In this paper, the use of the beta-emitter {sup 2}34Th as the most convenient tracer is discussed. Equations are derived for correcting for counting errors introduced by other thorium isotopes which are present either in the sample or in the tracer, as well as for calculating the chemical yield of the separation. These equations have been experimentally checked by ionium determinations carried out with different types of samples. (Author) 18 refs.

  20. Determination of betulinic acid, oleanolic acid and ursolic acid from Achyranthes aspera L. using RP-UFLC-DAD analysis and evaluation of various parameters for their optimum yield.

    Science.gov (United States)

    Pai, Sandeep R; Upadhya, Vinayak; Hegde, Harsha V; Joshi, Rajesh K; Kholkute, Sanjiva D

    2016-03-01

    Achyranthes aspera L. is a well known herb commonly used in traditional system of Indian medicine to treat various disorders, such as cough, dysentery, gonorrhea, piles, kidney stone, pneumonia, renal dropsy, skin eruptions, snake bite, etc. Here, we used RP-UFLC-DAD method for determining triterpenoids betulinic acid (BA), oleanolic acid (OA) and ursolic acid (UA) from A. aspera. Optimum yield of these compounds were studied and evaluated using parameters viz., method of extraction, time of extraction, age of plant and plant parts (leaves, stem and roots). Linear relationships in RP-UFLC-DAD analysis were obtained in the range 0.05-100 µg/mL with 0.035, 0.042 and 0.033 µg/mL LOD for BA, OA and UA, respectively. Of the variables tested, extraction method and parts used significantly affected content yield. Continuous shaking extraction (CSE) at ambient temperature gave better extraction efficiency than exposure to ultra sonic extraction (USE) or microwave assisted extraction (MAE) methods. The highest content of BA, OA and UA were determined individually in leaf, stem and root extracts with CSE. Collective yield of these triterpenoids were higher in leaf part exposed to 15 min USE method. To best of our knowledge, the study newly reports UA from A. aspera and the same was confirmed using ATR-FT-IR studies. This study explains the distribution pattern of these major triterpenoids and optimum extraction parameters in detail.

  1. The yield of DNA double strand breaks determined after exclusion of those forming from heat-labile lesions predicts tumor cell radiosensitivity to killing.

    Science.gov (United States)

    Cheng, Yanlei; Li, Fanghua; Mladenov, Emil; Iliakis, George

    2015-09-01

    The radiosensitivity to killing of tumor cells and in-field normal tissue are key determinants of radiotherapy response. In vitro radiosensitivity of tumor- and normal-tissue-derived cells often predicts radiation response, but high determination cost in time and resources compromise utility as routine response-predictor. Efforts to use induction or repair of DNA double-strand-breaks (DSBs) as surrogate-predictors of cell radiosensitivity to killing have met with limited success. Here, we re-visit this issue encouraged by our recent observations that ionizing radiation (IR) induces not only promptly-forming DSBs (prDSBs), but also DSBs developing after irradiation from the conversion to breaks of thermally-labile sugar-lesions (tlDSBs). We employ pulsed-field gel-electrophoresis and flow-cytometry protocols to measure total DSBs (tDSB=prDSB+tlDSBs) and prDSBs, as well as γH2AX and parameters of chromatin structure. We report a fully unexpected and in many ways unprecedented correlation between yield of prDSBs and radiosensitivity to killing in a battery of ten tumor cell lines that is not matched by yields of tDSBs or γH2AX, and cannot be explained by simple parameters of chromatin structure. We propose the introduction of prDSBs-yield as a novel and powerful surrogate-predictor of cell radiosensitivity to killing with potential for clinical application. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

  2. Determination of Chemical States of Mercury on Activated Carbon Using XANES

    International Nuclear Information System (INIS)

    Takaoka, Masaki; Takeda, Nobuo; Oshita, Kazuyuki; Yamamoto, Takashi; Tanaka, Tsunehiro; Uruga, Tomoya

    2007-01-01

    Although the adsorption of mercury vapor onto activated carbon is a widely used technology to prevent environmental release, the adsorption mechanism is not clearly understood. In this study, we determined the chemical states of mercury on two kinds of activated carbon using X-ray absorption near-edge spectroscopy (XANES) to elucidate the adsorption mechanism. The adsorption experiments of elemental mercury onto activated carbon were conducted under air and nitrogen atmospheres at temperatures of 20 and 160 deg. C. Two types of activated carbon were prepared. X-ray absorption fine structure (XAFS) measurements were carried out on beamline BL01B1 at SPring-8. Hg-LIII edge XANES spectra suggested that chemical adsorption of elemental mercury on the activated carbon occurred in the 20-160 deg. C temperature range. According to the XANES spectra, a difference occurred in the chemical states of mercury between AC no. 1 and AC no. 2. The Hg XANES spectra on AC no. 1 were similar to those of Hg2Cl2 and HgS, and the Hg XANES spectra on AC no. 2 were similar to that of HgO, which suggested that nitric acid treatment removed sulfur from AC no. 1 and functional groups that were strong oxidizers on the surface of AC no. 2 created HgO. According to the EXAFS oscillation, a difference occurred in the chemical states of mercury on AC no. 1 between 20 and 160 deg. C. We found that impurities and oxidant functional groups on activated carbon play key roles in mercury adsorption

  3. Fission-product yields for thermal-neutron fission of 243Cm determined from measurements with a high-resolution low-energy germanium gamma-ray detector

    International Nuclear Information System (INIS)

    Merriman, L.D.

    1984-04-01

    Cumulative fission-product yields have been determined for 13 gamma rays emitted during the decay of 12 fission products created by thermal-neutron fission of 243 Cm. A high-resolution low-energy germanium detector was used to measure the pulse-height spectra of gamma rays emitted from a 77-nanogram sample of 243 Cm after the sample had been irradiated by thermal neutrons. Analysis of the data resulted in the identification and matching of gamma-ray energies and half-lives to individual radioisotopes. From these results, 12 cumulative fission product yields were deduced for radionuclides with half-lives between 4.2 min and 84.2 min. 7 references

  4. The use of aldehyde indicators to determine glutaraldehyde and alkaline glutaraldehyde contamination in chemical protective gloves.

    Science.gov (United States)

    Vo, Evanly; Zhuang, Zhenzhen

    2009-07-01

    The aim of this study was to assess the use of aldehyde indicator pads for detection of glutaraldehyde and alkaline glutaraldehyde permeation through chemical protective gloves under simulated in-use conditions. The quantitative analysis of glutaraldehyde permeation through a glove material was determined for Metricide, Wavicide, and 50% glutaraldehyde following a solvent-desorption process and gas chromatographic analysis. All glutaraldehyde solutions exhibited >99% adsorption (including both the glutaraldehyde oligomers of the reaction product and the excess glutaraldehyde) on the pads over the spiking range 0.05-5.0 microL. Breakthrough times for protective gloves were determined using the Thermo-Hand test method, and found to range from 76 to 150, from 170 to 230, and from 232 to 300 min for Metricide, Wavicide, and 50% glutaraldehyde, respectively. Glutaraldehyde recovery was calculated and ranged from 61 to 80% for all glutaraldehyde solutions. The mass of glutaraldehyde in these solutions at the time of breakthrough detection ranged from 17 to 18, from 18 to 19, and from 19 to 20 microg/cm(2) for Wavicide, 50% glutaraldehyde solution, and Metricide, respectively. Aldehyde indicator pads and the Thermo-Hand test method together should find utility in detecting, collecting, and quantitatively analyzing glutaraldehyde permeation samples through chemical protective gloves under simulated in-use conditions.

  5. Determining treatment frequency for controlling weeds on traffic islands using chemical and non-chemical weed control

    DEFF Research Database (Denmark)

    Rask, Anne Merete; Larsen, S.U.; Andreasen, Christian

    2013-01-01

    Many public authorities rely on the use of non-chemical weed control methods, due to stringent restrictions on herbicide use in urban areas. However, these methods usually require more repeated treatments than chemical weed management, resulting in increased costs of weed management. In order...... of treatments per year were required: glyphosate 2.5, hot water 3, flames 5, hot air/flames 5.5 and steam 5.5 treatments. The results demonstrate that the weed control should be adjusted to the prescribed quality for the traffic islands by regularly assessing the need for weed control. They also show...... to investigate the efficacy of four non-chemical weed control methods and glyphosate treatment, experiments were carried out on traffic islands in the growing seasons 2005 and 2006. Three trial sites were each divided into six treatment areas, which were either treated with glyphosate, flame, steam, hot air...

  6. Nuclear and chemical data

    Energy Technology Data Exchange (ETDEWEB)

    De Regge, P.

    1978-12-15

    The neutron fission yield and other nuclear and chemical data of interest to the nuclear applications of mass spectrometry (mainly in the field of burnup determination) are examined. The performance of those determinations and the achievable accuracy should match the needs of the users of the data produced. 3 figures, 2 tables. (RWR)

  7. Increased precision for analysis of protein-ligand dissociation constants determined from chemical shift titrations

    Energy Technology Data Exchange (ETDEWEB)

    Markin, Craig J.; Spyracopoulos, Leo, E-mail: leo.spyracopoulos@ualberta.ca [University of Alberta, Department of Biochemistry (Canada)

    2012-06-15

    NMR is ideally suited for the analysis of protein-protein and protein ligand interactions with dissociation constants ranging from {approx}2 {mu}M to {approx}1 mM, and with kinetics in the fast exchange regime on the NMR timescale. For the determination of dissociation constants (K{sub D}) of 1:1 protein-protein or protein-ligand interactions using NMR, the protein and ligand concentrations must necessarily be similar in magnitude to the K{sub D}, and nonlinear least squares analysis of chemical shift changes as a function of ligand concentration is employed to determine estimates for the parameters K{sub D} and the maximum chemical shift change ({Delta}{delta}{sub max}). During a typical NMR titration, the initial protein concentration, [P{sub 0}], is held nearly constant. For this condition, to determine the most accurate parameters for K{sub D} and {Delta}{delta}{sub max} from nonlinear least squares analyses requires initial protein concentrations that are {approx}0.5 Multiplication-Sign K{sub D}, and a maximum concentration for the ligand, or titrant, of {approx}10 Multiplication-Sign [P{sub 0}]. From a practical standpoint, these requirements are often difficult to achieve. Using Monte Carlo simulations, we demonstrate that co-variation of the ligand and protein concentrations during a titration leads to an increase in the precision of the fitted K{sub D} and {Delta}{delta}{sub max} values when [P{sub 0}] > K{sub D}. Importantly, judicious choice of protein and ligand concentrations for a given NMR titration, combined with nonlinear least squares analyses using two independent variables (ligand and protein concentrations) and two parameters (K{sub D} and {Delta}{delta}{sub max}) is a straightforward approach to increasing the accuracy of measured dissociation constants for 1:1 protein-ligand interactions.

  8. Targeting acetylcholinesterase: identification of chemical leads by high throughput screening, structure determination and molecular modeling.

    Directory of Open Access Journals (Sweden)

    Lotta Berg

    Full Text Available Acetylcholinesterase (AChE is an essential enzyme that terminates cholinergic transmission by rapid hydrolysis of the neurotransmitter acetylcholine. Compounds inhibiting this enzyme can be used (inter alia to treat cholinergic deficiencies (e.g. in Alzheimer's disease, but may also act as dangerous toxins (e.g. nerve agents such as sarin. Treatment of nerve agent poisoning involves use of antidotes, small molecules capable of reactivating AChE. We have screened a collection of organic molecules to assess their ability to inhibit the enzymatic activity of AChE, aiming to find lead compounds for further optimization leading to drugs with increased efficacy and/or decreased side effects. 124 inhibitors were discovered, with considerable chemical diversity regarding size, polarity, flexibility and charge distribution. An extensive structure determination campaign resulted in a set of crystal structures of protein-ligand complexes. Overall, the ligands have substantial interactions with the peripheral anionic site of AChE, and the majority form additional interactions with the catalytic site (CAS. Reproduction of the bioactive conformation of six of the ligands using molecular docking simulations required modification of the default parameter settings of the docking software. The results show that docking-assisted structure-based design of AChE inhibitors is challenging and requires crystallographic support to obtain reliable results, at least with currently available software. The complex formed between C5685 and Mus musculus AChE (C5685•mAChE is a representative structure for the general binding mode of the determined structures. The CAS binding part of C5685 could not be structurally determined due to a disordered electron density map and the developed docking protocol was used to predict the binding modes of this part of the molecule. We believe that chemical modifications of our discovered inhibitors, biochemical and biophysical

  9. Application of [sup 57]Fe emission Moessbauer spectroscopy to the investigation of the physico-chemical consequences of the double radioactive decay [sup 57]Ni[yields][sup 57]Co[yields][sup 57]Fe in the solid state

    Energy Technology Data Exchange (ETDEWEB)

    Devillers, M.; Ladriere, J. (Univ. Catholique de Louvain, Louvain-la-Neuve (Belgium). Lab. de Chimie Inorganique et Nucleaire)

    1994-04-01

    [sup 57]Fe emission Mossbauer spectroscopy is shown to be a useful technique for investigating the cumulative recoil and Auger after-effects associated with the double electron capture decay, [sup 57]Ni[yields][sup 57]Co''->[sup 57]Fe, in the solid state. Experimental results collected in several types of nickel-containing matrices are surveyed: conducting materials (Ni metal), ionic compounds with monoatomic ligands [potassium trifluoronickelate (II)] and coordination compounds with polyatomic ligands (carboxylates). (Author).

  10. Role of aquaporins in determining transpiration and photosynthesis in water-stressed plants: crop water-use efficiency, growth and yield.

    Science.gov (United States)

    Moshelion, Menachem; Halperin, Ofer; Wallach, Rony; Oren, Ram; Way, Danielle A

    2015-09-01

    The global shortage of fresh water is one of our most severe agricultural problems, leading to dry and saline lands that reduce plant growth and crop yield. Here we review recent work highlighting the molecular mechanisms allowing some plant species and genotypes to maintain productivity under water stress conditions, and suggest molecular modifications to equip plants for greater production in water-limited environments. Aquaporins (AQPs) are thought to be the main transporters of water, small and uncharged solutes, and CO2 through plant cell membranes, thus linking leaf CO2 uptake from the intercellular airspaces to the chloroplast with water loss pathways. AQPs appear to play a role in regulating dynamic changes of root, stem and leaf hydraulic conductivity, especially in response to environmental changes, opening the door to using AQP expression to regulate plant water-use efficiency. We highlight the role of vascular AQPs in regulating leaf hydraulic conductivity and raise questions regarding their role (as well as tonoplast AQPs) in determining the plant isohydric threshold, growth rate, fruit yield production and harvest index. The tissue- or cell-specific expression of AQPs is discussed as a tool to increase yield relative to control plants under both normal and water-stressed conditions. © 2014 John Wiley & Sons Ltd.

  11. X-ray induced singlet oxygen generation by nanoparticle-photosensitizer conjugates for photodynamic therapy: determination of singlet oxygen quantum yield

    OpenAIRE

    Clement, Sandhya; Deng, Wei; Camilleri, Elizabeth; Wilson, Brian C.; Goldys, Ewa M.

    2016-01-01

    Singlet oxygen is a primary cytotoxic agent in photodynamic therapy. We show that CeF3 nanoparticles, pure as well as conjugated through electrostatic interaction with the photosensitizer verteporfin, are able to generate singlet oxygen as a result of UV light and 8?keV X-ray irradiation. The X-ray stimulated singlet oxygen quantum yield was determined to be 0.79???0.05 for the conjugate with 31 verteporfin molecules per CeF3 nanoparticle, the highest conjugation level used. From this result ...

  12. Near infrared spectroscopy for determination of various physical, chemical and biochemical properties in Mediterranean soils.

    Science.gov (United States)

    Zornoza, R; Guerrero, C; Mataix-Solera, J; Scow, K M; Arcenegui, V; Mataix-Beneyto, J

    2008-07-01

    The potential of near infrared (NIR) reflectance spectroscopy to predict various physical, chemical and biochemical properties in Mediterranean soils from SE Spain was evaluated. Soil samples (n=393) were obtained by sampling thirteen locations during three years (2003-2005 period). These samples had a wide range of soil characteristics due to variations in land use, vegetation cover and specific climatic conditions. Biochemical properties also included microbial biomarkers based on phospholipid fatty acids (PLFA). Partial least squares (PLS) regression with cross validation was used to establish relationships between the NIR spectra and the reference data from physical, chemical and biochemical analyses. Based on the values of coefficient of determination (r(2)) and the ratio of standard deviation of validation set to root mean square error of cross validation (RPD), predicted results were evaluated as excellent (r(2)>0.90 and RPD>3) for soil organic carbon, Kjeldahl nitrogen, soil moisture, cation exchange capacity, microbial biomass carbon, basal soil respiration, acid phosphatase activity, β-glucosidase activity and PLFA biomarkers for total bacteria, Gram positive bacteria, actinomycetes, vesicular-arbuscular mycorrhizal fungi and total PLFA biomass. Good predictions (0.81fungi were not accurate enough to satisfactorily estimate these variables, only permitting approximate predictions (0.66chemical and biochemical soil properties for Mediterranean soils, including variables related to the composition of the soil microbial community composition.

  13. Rendimento, composição química e atividade antilisterial de óleos essenciais de espécies de Cymbopogon Yield, chemical composition and antilisterial activity of essential oils from Cymbopogon species

    Directory of Open Access Journals (Sweden)

    M.M.M Oliveira

    2011-01-01

    Full Text Available Objetivou-se determinar o rendimento, a composição química e avaliar a atividade antilisterial dos óleos essenciais de Cymbopogon citratus (DC. Stapf. (capim-limão e Cymbopogon nardus (L. Rendle (capim-citronela, puros e em combinação. A obtenção dos óleos essenciais foi realizada a partir de folhas frescas, empregando-se a técnica de hidrodestilação e utilizando-se aparelho de Clevenger modificado. Os rendimentos foram calculados a partir da massa obtida na extração e da umidade do material vegetal. A análise qualitativa foi realizada por cromatografia em fase gasosa acoplada à espectrometria de massas e a avaliação dos teores dos constituintes químicos por cromatografia em fase gasosa com detector de ionização de chamas. O efeito bacteriostático de diferentes concentrações dos óleos essenciais, puros e em combinação, foi determinado pela técnica de difusão em ágar. As concentrações mínimas inibitórias (CMIs foram utilizadas na determinação do tempo de ação bactericida. O rendimento, em base seca, foi de 1,39% (v/p para o óleo essencial de C. citratus e de 2,27% (v/p para o óleo essencial de C. nardus. Geranial e neral foram os constituintes majoritários do óleo essencial de C. citratus, enquanto, para C. nardus, foram citronelal, geraniol e citronelol. A maioria das concentrações utilizadas mostrou-se efetiva contra Listeria monocytogenes e observaram-se efeitos bactericidas nas CMIs. Óleos essenciais de C. citratus e C. nardus, puros e em combinação, constituem novas alternativas de antibacterianos naturais a serem utilizados no controle de L. monocytogenes na indústria de alimentos.The aim of this study was to determine the yield and the chemical composition of essential oils from Cymbopogon citratus (DC. Stapf. (lemongrass and Cymbopogon nardus (L. Rendle (citronella, and to evaluate their antilisterial activity when pure and combined. The essential oils were obtained from fresh leaves

  14. Chemometrics-assisted spectrophotometry method for the determination of chemical oxygen demand in pulping effluent.

    Science.gov (United States)

    Chen, Honglei; Chen, Yuancai; Zhan, Huaiyu; Fu, Shiyu

    2011-04-01

    A new method has been developed for the determination of chemical oxygen demand (COD) in pulping effluent using chemometrics-assisted spectrophotometry. Two calibration models were established by inducing UV-visible spectroscopy (model 1) and derivative spectroscopy (model 2), combined with the chemometrics software Smica-P. Correlation coefficients of the two models are 0.9954 (model 1) and 0.9963 (model 2) when COD of samples is in the range of 0 to 405 mg/L. Sensitivities of the two models are 0.0061 (model 1) and 0.0056 (model 2) and method detection limits are 2.02-2.45 mg/L (model 1) and 2.13-2.51 mg/L (model 2). Validation experiment showed that the average standard deviation of model 2 was 1.11 and that of model 1 was 1.54. Similarly, average relative error of model 2 (4.25%) was lower than model 1 (5.00%), which indicated that the predictability of model 2 was better than that of model 1. Chemometrics-assisted spectrophotometry method did not need chemical reagents and digestion which were required in the conventional methods, and the testing time of the new method was significantly shorter than the conventional ones. The proposed method can be used to measure COD in pulping effluent as an environmentally friendly approach with satisfactory results.

  15. Determination of chemical elements in Eucalyptus grandis, manured with Ballad's, by neutrons activation analysis

    International Nuclear Information System (INIS)

    Mateus, Natalina de Fatima; Madi Filho, Tufic

    2007-01-01

    The biosolid is a mud resulting from the biological treatment of wasted liquids. It is considered as a profitable alternative and important to minimize the environmental impact generated by the sewage thrown in to sanitary lands, in forest cultures like the Eucalyptus grandis. The objective of this work was to detect which chemical elements are present in Eucalyptus grandis samples, fertilized with different quantities of biosolid. The eucalyptuses of Estacao Experimental de Ciencias Florestais of Itatinga were planted in March of 1998 and collected with five years old. The used biosolid was produced by Station of Treatment of Sewer of Barueri - SP, classified as kind B. For the determination of the presence and quantity of chemical elements in the eucalyptus samples, an analysis technique by neutronic activation (NAA) was used followed by gamma rays spectroscopy. The samples were irradiated in the Nuclear Reactor IEA-R1 of IPEN-SP, followed by the measure of induced gamma rays activity, using a Detector HPGe. The presence, mainly of Br, Mn, Na and K, was detected in all analyzed samples. (author)

  16. Measurements of fission yields

    International Nuclear Information System (INIS)

    Denschlag, H.O.

    2000-01-01

    After some historical introductory remarks on the discovery of nuclear fission and early fission yield determinations, the present status of knowledge on fission yields is briefly reviewed. Practical and fundamental reasons motivating the pursuit of fission yield measurements in the coming century are pointed out. Recent results and novel techniques are described that promise to provide new interesting insights into the fission process during the next century. (author)

  17. Determination of solvents permeating through chemical protective clothing with a microsensor array.

    Science.gov (United States)

    Park, J; Zellers, E T

    2000-08-01

    The performance of a novel prototype instrument in determining solvents and solvent mixtures permeating through samples of chemical protective clothing (CPC) materials was evaluated. The instrument contains a mini-preconcentrator and an array of three polymer-coated surface-acoustic-wave (SAW) microsensors whose collective response patterns are used to discriminate among multiple permeants. Permeation tests were performed with a 2.54 cm diameter test cell in an open-loop configuration on samples of common glove materials challenged with four individual solvents, three binary mixtures, and two ternary mixtures. Breakthrough times, defined as the times required for the permeation rate to reach a value of 1 microg cm(-2) min(-1), determined by the instrument were within 3 min of those determined in parallel by manual sampling and gas chromatographic analysis. Permeating solvents were recognized (identified) from their response patterns in 59 out of 64 measurements (92%) and their vapor concentrations were quantified to an accuracy of +/- 31% (typically +/- 10%). These results demonstrate the potential for such instrumentation to provide semi-automated field or bench-top screening of CPC permeation resistance.

  18. Application of X-ray fluorescence (WDXRF): thickness and chemical composition determination of thin films

    International Nuclear Information System (INIS)

    Scapin, Valdirene de Oliveira.

    2004-01-01

    In this work a procedure is described for thickness and quantitative chemical composition of thin films by wavelength dispersion X-ray fluorescence (WDXRF) using Fundamental Parameters method. This method was validated according to quality assurance standard and applied sample Al, Cr, TiO2, Ni, ZrO2 (single thickness) and Ni/Cr (double thickness) on glass; Ni on steel and metallic zinc and TiO2 on metallic iron (single thickness), all the sample were prepared for physical deposition of vapor (PVD). The thickness had been compared with Absorption (FRX-A) and Rutherford Backscattering Spectrometry (RBS) methods; the result showed good efficiency of the fundamental parameters method. Sample structural characteristics analyzed by X ray diffraction (XRD) showed any influence in the thickness determinations. (author)

  19. Chemical Methods for the Determination of Soluble and Insoluble Non-Starch Polysaccharides - Review

    Directory of Open Access Journals (Sweden)

    Rodica Căpriţă

    2011-10-01

    Full Text Available Polysaccharides are macromolecules of monosaccharides linked by glycosidic bonds. Non-starch polysaccharides(NSP are principally non-α-glucan polysaccharides of the plant cell wall. They are a heterogeneous group ofpolysaccharides with varying degrees of water solubility, size, and structure. The water insoluble fiber fractioninclude cellulose, galactomannans, xylans, xyloglucans, and lignin, while the water-soluble fibers are the pectins,arabinogalactans, arabinoxylans, and β-(1,3(1,4-D-glucans (β-glucans. Both the enzymatic-gravimetric andenzymatic-chemical methods used for the determination of soluble and insoluble non-starch polysaccharides haveundergone a number of modifications and improvements, most occurring over the last 20 years.

  20. Technology assessment for the determination of chemical agent vapors in demilitarization facilities: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Maskarinec, M.P.; Wise, M.B.; Buchanan, M.V.

    1987-01-01

    A survey of analytical methods for the determination of chemical agents GB, VX, and HD was made. HD, or mustard, is bis-2-chloroethyl sulfide, and is classified as a blishtering agent. GB, or Sarin, is isopropyl methyl phosphonofluoridate. VX is O-ethyl-S-(2-diisopropylaminoethyl)methylphosphonothioate. Both GB and VX are nerve agents. Included were methods capable of providing for monitoring requirements at the time weighted average (TWA) and allowable stack concentration (ASC) levels in near real time. A review of the currently used automatic continuous air monitoring system (ACAMS) was made as well as a review of the recently developed atmospheric pressure ionization mass spectrometry (APIMS). This report recommends a strategy for research and development for near term and medium term improvement of the overall monitoring program. 12 refs., 1 tab.

  1. Using 1H and 13C NMR chemical shifts to determine cyclic peptide conformations: a combined molecular dynamics and quantum mechanics approach.

    Science.gov (United States)

    Nguyen, Q Nhu N; Schwochert, Joshua; Tantillo, Dean J; Lokey, R Scott

    2018-05-10

    Solving conformations of cyclic peptides can provide insight into structure-activity and structure-property relationships, which can help in the design of compounds with improved bioactivity and/or ADME characteristics. The most common approaches for determining the structures of cyclic peptides are based on NMR-derived distance restraints obtained from NOESY or ROESY cross-peak intensities, and 3J-based dihedral restraints using the Karplus relationship. Unfortunately, these observables are often too weak, sparse, or degenerate to provide unequivocal, high-confidence solution structures, prompting us to investigate an alternative approach that relies only on 1H and 13C chemical shifts as experimental observables. This method, which we call conformational analysis from NMR and density-functional prediction of low-energy ensembles (CANDLE), uses molecular dynamics (MD) simulations to generate conformer families and density functional theory (DFT) calculations to predict their 1H and 13C chemical shifts. Iterative conformer searches and DFT energy calculations on a cyclic peptide-peptoid hybrid yielded Boltzmann ensembles whose predicted chemical shifts matched the experimental values better than any single conformer. For these compounds, CANDLE outperformed the classic NOE- and 3J-coupling-based approach by disambiguating similar β-turn types and also enabled the structural elucidation of the minor conformer. Through the use of chemical shifts, in conjunction with DFT and MD calculations, CANDLE can help illuminate conformational ensembles of cyclic peptides in solution.

  2. Determination of chemical state of Al doping element in ZnO layer

    International Nuclear Information System (INIS)

    Csik, A.; Toth, J.; Lovics, R.; Takats, V.; Hakl, J.; Vad, K.

    2011-01-01

    profiling of these layered structures. After determination of the depth of the embedded AlO layer with the precision of 1 nm, we sputtered the upper ZnO atomic layers until the AlO layer was revealed and determined the chemical state of Al in the thin AlO layer by the XPS instrument. During the whole experiment the samples were in high vacuum so as to exclude the contamination of the surface. Acknowledgements. This work was supported by the National Office for Research and Technology (Grant nos. OTKA 73424 and TFSOLAR2).

  3. 6 CFR 27.205 - Determination that a chemical facility “presents a high level of security risk.”

    Science.gov (United States)

    2010-01-01

    ... 6 Domestic Security 1 2010-01-01 2010-01-01 false Determination that a chemical facility âpresents... SECURITY, OFFICE OF THE SECRETARY CHEMICAL FACILITY ANTI-TERRORISM STANDARDS Chemical Facility Security Program § 27.205 Determination that a chemical facility “presents a high level of security risk.” (a...

  4. Fission product yields

    International Nuclear Information System (INIS)

    Valenta, V.; Hep, J.

    1978-01-01

    Data are summed up necessary for determining the yields of individual fission products from different fissionable nuclides. Fractional independent yields, cumulative and isobaric yields are presented here for the thermal fission of 235 U, 239 Pu, 241 Pu and for fast fission (approximately 1 MeV) of 235 U, 238 U, 239 Pu, 241 Pu; these values are included into the 5th version of the YIELDS library, supplementing the BIBFP library. A comparison is made of experimental data and possible improvements of calculational methods are suggested. (author)

  5. Chemical preparation of biological materials for accurate chromium determination by isotope dilution mass spectrometry

    International Nuclear Information System (INIS)

    Dunstan, L.P.; Garner, E.L.

    1977-01-01

    The current interest in trace elements in biological materials has created a need for accurate methods of analysis. The source of discrepancies and variations in chromium concentration determinations is often traceable to inadequate methods of sample preparation. Any method of Cr analysis that requires acid digestion of a biological matrix must take into consideration the existence or formation of a volatile Cr component. In addition, because Cr is often present at concentrations less than 1 μg/g, the analytical blank becomes a potential source of error. Chemical procedures have been developed for the digestion of the biological matrix and the separation of Cr without either large analytical blanks or significant losses by volatilization. These procedures have been used for the analysis of NBS Standard Reference Material (SRM) 1569 Brewers Yeast; SRM 1577 Bovine Liver; SRM 1570 Spinach and other biological materials including human hair and nails. At this time, samples containing 1 μg of Cr can be determined with an estimated accuracy of 2 percent

  6. Precession technique and electron diffractometry as new tools for crystal structure analysis and chemical bonding determination

    International Nuclear Information System (INIS)

    Avilov, A.; Kuligin, K.; Nicolopoulos, S.; Nickolskiy, M.; Boulahya, K.; Portillo, J.; Lepeshov, G.; Sobolev, B.; Collette, J.P.; Martin, N.; Robins, A.C.; Fischione, P.

    2007-01-01

    We have developed a new fast electron diffractometer working with high dynamic range and linearity for crystal structure determinations. Electron diffraction (ED) patterns can be scanned serially in front of a Faraday cage detector; the total measurement time for several hundred ED reflections can be tens of seconds having high statistical accuracy for all measured intensities (1-2%). This new tool can be installed to any type of TEM without any column modification and is linked to a specially developed electron beam precession 'Spinning Star' system. Precession of the electron beam (Vincent-Midgley technique) reduces dynamical effects allowing also use of accurate intensities for crystal structure analysis. We describe the technical characteristics of this new tool together with the first experimental results. Accurate measurement of electron diffraction intensities by electron diffractometer opens new possibilities not only for revealing unknown structures, but also for electrostatic potential determination and chemical bonding investigation. As an example, we present detailed atomic bonding information of CaF 2 as revealed for the first time by precise electron diffractometry

  7. Hydrogen determination in chemically delithiated lithium ion battery cathodes by prompt gamma activation analysis

    Science.gov (United States)

    Alvarez, Emilio, II

    2007-12-01

    Lithium ion batteries, due to their relatively high energy density, are now widely used as the power source for portable electronics. Commercial lithium ion cells currently employ layered LiCoO2 as a cathode but only 50% of its theoretical capacity can be utilized. The factors that cause the limitation are not fully established in the literature. With this perspective, prompt gamma-ray activation analysis (PGAA) has been employed to determine the hydrogen content in various oxide cathodes that have undergone chemical extraction of lithium (delithiation). The PGAA data is complemented by data obtained from atomic absorption spectroscopy (AAS), redox titration, thermogravimetric analysis (TGA), and mass spectroscopy to better understand the capacity limitations and failure mechanisms of lithium ion battery cathodes. As part of this work, the PGAA facility has been redesigned and reconstructed. The neutron and gamma-ray backgrounds have been reduced by more than an order of magnitude. Detection limits for elements have also been improved. Special attention was given to the experimental setup including potential sources of error and system calibration for the detection of hydrogen. Spectral interference with hydrogen arising from cobalt was identified and corrected for. Limits of detection as a function of cobalt mass present in a given sample are also discussed. The data indicates that while delithiated layered Li1- xCoO2, Li1-xNi 1/3Mn1/3Co1/3O2, and Li1- xNi0.5Mn0.5O2 take significant amounts of hydrogen into the lattice during deep extraction, orthorhombic Li 1-xMnO2, spinel Li1- xMn2O4, and olivine Li1- xFePO4 do not. Layered LiCoO2, LiNi 0.5Mn0.5O2, and LiNi1/3Mn1/3Co 1/3O2 have been further analyzed to assess their relative chemical instabilities while undergoing stepped chemical delithiation. Each system takes increasing amounts of protons at lower lithium contents. The differences are attributed to the relative chemical instabilities of the various cathodes

  8. Latest Developments in Data Analysis and Structure Determination and Refinement: Software for Chemical Crystallography

    International Nuclear Information System (INIS)

    Dix, I.; Adam, M.; Jacob, H. F.; Roter, A.

    2003-01-01

    The introduction of a two-dimensional CCD X-ray detector nearly 10 years ago by Bruker started a revolution in chemical crystallography. Since then, crystallographers can accomplish a complete data collection even of small and poorly scattering crystals in a few hours instead of days. The launch of the kappa geometry by Nonius a few years ago beforehand equally revolutionized the field of single crystal diffractometry. Currently Bruker Nonius has far more than 500 CCD systems installed. The latest development of Bruker Nonius, the X8 APEX, is the powerful combination of both: the APEX CCD detector and the unique Kappa four-circle goniometer. The APEX 4K CCD detector provides the utmost sensitivity, while the Kappa four-circle goniometer offers a very open geometry, granting all the flexibility to align any crystallographic axis. This provides a more efficient data collection for axial photographs to investigate e.g. diffuse scattering or incommensurate structures. Even the crystal-detector distance is computer-controlled for precise and superior data collection. The X8 APEX software suite gives a whole new look to the CCD users interface. It not only has improved data collection abilities, but also guides the chemist or mineralogist through gathering the raw crystal data to producing the final crystal structure. It provides context-dependent menus, which are well-known from business software packages such as Outlook. The tools for unit cell determination, views into reciprocal space, optimisation of the data collection strategy, data integration, scaling and correcting (SADABS) as well as tools for structure solving and refining (SHELXTL package) will be presented. Low temperature work has become an essential tool for challenging samples. The Bruker Nonius Kryo-Flex cryogenic device makes chemical crystallography at low temperatures a routine method in your laboratory. Of course, the Kryo-Flex is fully controlled by the new graphical user interface of the X8 APEX

  9. Bond yield curve construction

    Directory of Open Access Journals (Sweden)

    Kožul Nataša

    2014-01-01

    Full Text Available In the broadest sense, yield curve indicates the market's view of the evolution of interest rates over time. However, given that cost of borrowing it closely linked to creditworthiness (ability to repay, different yield curves will apply to different currencies, market sectors, or even individual issuers. As government borrowing is indicative of interest rate levels available to other market players in a particular country, and considering that bond issuance still remains the dominant form of sovereign debt, this paper describes yield curve construction using bonds. The relationship between zero-coupon yield, par yield and yield to maturity is given and their usage in determining curve discount factors is described. Their usage in deriving forward rates and pricing related derivative instruments is also discussed.

  10. Comparison of Chemical Extraction Methods for Determination of Soil Potassium in Different Soil Types

    Science.gov (United States)

    Zebec, V.; Rastija, D.; Lončarić, Z.; Bensa, A.; Popović, B.; Ivezić, V.

    2017-12-01

    Determining potassium supply of soil plays an important role in intensive crop production, since it is the basis for balancing nutrients and issuing fertilizer recommendations for achieving high and stable yields within economic feasibility. The aim of this study was to compare the different extraction methods of soil potassium from arable horizon of different types of soils with ammonium lactate method (KAL), which is frequently used as analytical method for determining the accessibility of nutrients and it is a common method used for issuing fertilizer recommendations in many Europe countries. In addition to the ammonium lactate method (KAL, pH 3.75), potassium was extracted with ammonium acetate (KAA, pH 7), ammonium acetate ethylenediaminetetraacetic acid (KAAEDTA, pH 4.6), Bray (KBRAY, pH 2.6) and with barium chloride (K_{BaCl_2 }, pH 8.1). The analyzed soils were extremely heterogeneous with a wide range of determined values. Soil pH reaction ( {pH_{H_2 O} } ) ranged from 4.77 to 8.75, organic matter content ranged from 1.87 to 4.94% and clay content from 8.03 to 37.07%. In relation to KAL method as the standard method, K_{BaCl_2 } method extracts 12.9% more on average of soil potassium, while in relation to standard method, on average KAA extracts 5.3%, KAAEDTA 10.3%, and KBRAY 27.5% less of potassium. Comparison of analyzed extraction methods of potassium from the soil is of high precision, and most reliable comparison was KAL method with KAAEDTA, followed by a: KAA, K_{BaCl_2 } and KBRAY method. Extremely significant statistical correlation between different extractive methods for determining potassium in the soil indicates that any of the methods can be used to accurately predict the concentration of potassium in the soil, and that carried out research can be used to create prediction model for concentration of potassium based on different methods of extraction.

  11. Determine the Optimal Levels of Bio-fertilizers and Foliar Application of Iron on Yield and Quality Indices of Roselle (Hibiscus sabdariffa L.

    Directory of Open Access Journals (Sweden)

    zahra mir

    2018-02-01

    Full Text Available Introduction In conventional agricultural systems to obtain the highest performance continuous use of chemical fertilizers is inevitable. The health of the plant, soil and living matter depends on the rotation of food elements in the ecosystem. This cycle is disrupted as a result of the loss of soil fertility, its food imbalance and inappropriate cultivation practices. Bio-fertilizers are composed of beneficial microorganisms, each for a specific purpose, such as nitrogen fixation, release of phosphate ions, potassium, iron. It should be noted that most studies in the field for sour Roselle (Hibiscus sabdariffa are based on the use of various chemical fertilizers, but the reaction of this plant to bio-fertilizers and iron solubilization has not been considered. Therefore, this study aimed to investigate the effect of bio fertilizers and iron on yield and quality traits of Roselle in hot and dry weather conditions. Materials and Methods In order to investigate the effects of bio-fertilizers and foliar application iron on yield and quality indicators Roselle (Hibiscus sabdariffa experiment in Research field of Zabol University Agriculture Institute in 2015-2016 years was performed with split-plot based on completely randomized design and three replications. Treatments consisted of four levels of bio-fertilizers: control (without fertilizer, vermicompost, cow manure, seaweed and iron foliar applications include: lack of iron, foliar application at a rate of 3cc per thousand, 6cc per thousand was considered. As a source of bio-fertilizer treatments and foliar application iron levels were considered as sub plots. Before sowing Roselle seeds, vermicompost and manure were added to the soil and inoculation operation . Measurements were: economic yield, biological yield, harvest index, chlorophyll a, b and carotenoids, anthocyanins, carbohydrates and protein. Statistical analysis of data was done with SAS software version 9.1 and mean comparison with

  12. Quantitative chemical method for the determination of the disordered carbon component in pyrocarbon coatings of fuel particles

    International Nuclear Information System (INIS)

    Wolfrum, E.A.; Nickel, H.

    1977-01-01

    The chemical behavior of the surface of pyrocarbon (PyC) coatings of nuclear fuel particles was investigated in aqueous suspension by reaction with oxygen at room temperature. The concentration of the disordered material component, which has a large internal surface, can be identified by means of a pH change. Using this fact, a chemical method was developed that can be used for the quantitative determination of the concentration of this carbon component in the PyC coating

  13. Preparation and Determination of the Physical and Chemical Properties of Margarine

    Directory of Open Access Journals (Sweden)

    Habazin, S.

    2012-02-01

    Full Text Available Nutrition is one of the most basic needs of the human body. It ensures the introduction of substances needed to sustain life of the organism, its growth and proper development. In the food pyramid, fats together with carbohydrates are at the very top. One source of fat in human nutrition is margarine. Margarine comprises at least 82 % vegetable fats and 16 % water. The remainder consists of lecithin, sugar, salt, colours, and vitamins.The margarine production process involves hydrogenation of vegetable fats, assembling the margarine mixture, emulsifying, crystallization and packing.The objective of this study was to show that margarine could be prepared in a school laboratory under conditions that are applicable for such laboratory. Meaning:a In a school laboratory at normal pressure and at elevated temperature with nickel as catalyst, i.e. without the use of an autoclave, carry out the reaction of hydrogenation soybean and palm oil in order to obtain a vegetable fat that is the basic ingredient of margarine. During the preparation of margarine, the hydrogenation reaction was carefully monitored by determining the iodine value.b Preparation of margarine obtained from vegetable fats.c Determination and comparison of selected physical and chemical properties of the product with the same properties of several types of margarines available on the market. The following properties were determined:– Melting point, in order to obtain composition of fat phase and determine suitability for humanuse.– Acid value, as an indicator of the amount of free fatty acids that influence the taste.– Peroxide value, for insight into the oxidative stability of fats.This work has shown that it is possible to make vegetable fat in a school lab by hydrogenation of vegetable oils. Unlike the industrial process of hydrogenation carried out under a pressure of 0.36 to 2 atm, which takes about two hours, our reaction was carried out at atmospheric pressure but with a

  14. Yield Traits, Physico-chemical Characteristics and Nutritional Composition of MR219 M3 Generation and its Effect on Glycemic Index and Responses in Animal Model

    International Nuclear Information System (INIS)

    Asma Ilyani Kadar; Sobri Hussein; Abdul Rahim Harun; Fazliana Mohd Saaya

    2014-01-01

    Mutation technique is a conventional breeding technique and it is very effective in improving of main crop characteristics such as yield traits, resistance to diseases and pests and nutritional qualities. In this study, MR219 seeds were treated with Carbon ion radiation (60 Gy) by AVF-Cyclotron at the Japan Atomic Energy Research Institute (JAERI), Takasaki, Japan and were planted at the Malaysian Nuclear Agency up to third mutant generation (M3). Thirty one M3 mutant lines (ML1 to ML31) were evaluated on morphological, yield and yield components, and were compared to the parental variety, MR219. Analysis of variance revealed that there was a significant difference among mutant lines in culm height, days to flowering, number of tillers, number of panicles, 1000 grain weight, total grain weight, total of dry matter, alkaline spreading value, gel consistency, amylose content, ash, crude protein, fat, dietary fibre, carbohydrate and energy. Mutant line ML21 had the best performance in majority of yield components and vegetative traits as compared to others mutant lines and parental variety. For nutritional composition, mutant lines namely ML31, ML21, ML10, ML19 were improved in crude protein content, dietary fibre and carbohydrate content. The estimation of glycemic index revealed that two mutant lines namely ML3 and ML30 can be consumed by diabetics. (author)

  15. Determining airborne concentrations of spatial repellent chemicals in mosquito behavior assay systems.

    Directory of Open Access Journals (Sweden)

    Nicholas J Martin

    Full Text Available BACKGROUND: Mosquito behavior assays have been used to evaluate the efficacy of vector control interventions to include spatial repellents (SR. Current analytical methods are not optimized to determine short duration concentrations of SR active ingredients (AI in air spaces during entomological evaluations. The aim of this study was to expand on our previous research to further validate a novel air sampling method to detect and quantitate airborne concentrations of a SR under laboratory and field conditions. METHODOLOGY/PRINCIPAL FINDINGS: A thermal desorption (TD gas chromatography-mass spectrometry (GC-MS method was used to determine the amount of dichlorodiphenyltrichloroethane (DDT in samples of air. During laboratory experiments, 1 L volumes of air were collected over 10 min intervals from a three-chamber mosquito behavior assay system. Significantly higher levels of airborne DDT were measured in the chamber containing textiles treated with DDT compared to chambers free of AI. In the field, 57 samples of air were collected from experimental huts with and without DDT for onsite analysis. Airborne DDT was detected in samples collected from treated huts. The mean DDT air concentrations in these two huts over a period of four days with variable ambient temperature were 0.74 µg/m(3 (n = 17; SD = 0.45 and 1.42 µg/m(3 (n = 30; SD = 0.96. CONCLUSIONS/SIGNIFICANCE: The results from laboratory experiments confirmed that significantly different DDT exposure conditions existed in the three-chamber system establishing a chemical gradient to evaluate mosquito deterrency. The TD GC-MS method addresses a need to measure short-term (<1 h SR concentrations in small volume (<100 L samples of air and should be considered for standard evaluation of airborne AI levels in mosquito behavior assay systems. Future studies include the use of TD GC-MS to measure other semi-volatile vector control compounds.

  16. Application of FT NIR Spectroscopy in the Determination of Basic Physical and Chemical Properties of Sausages

    Directory of Open Access Journals (Sweden)

    Zuzana Procházková

    2010-01-01

    Full Text Available The objectives of this study were to develop calibration models for determination of water activity and the content of fat, dry matter, salt, non collagen muscle protein and pH in dry cooked sausages. Samples (n = 42 were scanned in FT-NIR Analyzer and simultaneously analyzed by standard methods. The spectra were measured in the reflectance mode with a compressive cell between 10 000 and 4 000 cm-1, averaging 100 scans. Calibration models were developed using the partial least squares (PLS method. These calibration models were checked later by crossvalidation. The following statistical values were obtained: R (correlation coefficient = 0.997 and SEC (standard error of calibration = 0.002 for water activity, R = 0.966 and SEC = 0.023 for pH, R = 0.995 and SEC = 0.970 for dry matter content, R = 0.995 and SEC = 0.045 for salt content, R = 0.965 and SEC = 0.652 for non collagen muscle protein, R = 0.996 and SEC = 0.559 for fat content. The results of the study showed that FT-NIR is a suitable method for rapid analysis of physical and chemical properties of sausages.

  17. Quantitative Determination of Catechin as Chemical Marker in Pediatric Polyherbal Syrup by HPLC/DAD.

    Science.gov (United States)

    Sheikh, Zeeshan A; Siddiqui, Zafar A; Naveed, Safila; Usmanghani, Khan

    2016-09-01

    Vivabon syrup is a balanced composition of dietary ingredients of phytopharmaceutical nature for maintaining the physique, vigor, vitality and balanced growth of children. The herbal ingredients of pediatric syrup are rich in bioflavonoid, proteins, vitamins, glycosides and trace elements. Vivabon is formulated with herbal drugs such as Phoenix sylvestris, Emblica officinalis, Withania somnifera, Centella asiatica, Amomum subulatum, Zingiber officinalis, Trigonella foenum-graecum, Centaurea behen and Piper longum Catechins are flavan-3-ols that are found widely in the medicinal herbs and are utilized for anti-inflammatory, cardio protective, hepato-protective, neural protection and other biological activities. In general, the dietary intake of flavonoids has been regarded traditionally as beneficial for body growth. Standardization of Vivabon syrup dosage form using HPLC/DAD has been developed for quantitative estimation of Catechin as a chemical marker. The method was validated as per ICH guidelines. Validation studies demonstrated that the developed HPLC method is quite distinct, reproducible as well as quick and fast. The relatively high recovery and low comparable standard deviation confirm the suitability of the developed method for the determination of Catechin in syrup. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  18. Desorption modeling of hydrophobic organic chemicals from plastic sheets using experimentally determined diffusion coefficients in plastics.

    Science.gov (United States)

    Lee, Hwang; Byun, Da-Eun; Kim, Ju Min; Kwon, Jung-Hwan

    2018-01-01

    To evaluate rate of migration from plastic debris, desorption of model hydrophobic organic chemicals (HOCs) from polyethylene (PE)/polypropylene (PP) films to water was measured using PE/PP films homogeneously loaded with the HOCs. The HOCs fractions remaining in the PE/PP films were compared with those predicted using a model characterized by the mass transfer Biot number. The experimental data agreed with the model simulation, indicating that HOCs desorption from plastic particles can generally be described by the model. For hexachlorocyclohexanes with lower plastic-water partition coefficients, desorption was dominated by diffusion in the plastic film, whereas desorption of chlorinated benzenes with higher partition coefficients was determined by diffusion in the aqueous boundary layer. Evaluation of the fraction of HOCs remaining in plastic films with respect to film thickness and desorption time showed that the partition coefficient between plastic and water is the most important parameter influencing the desorption half-life. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. Evaluating chemical extraction techniques for the determination of uranium oxidation state in reduced aquifer sediments

    Science.gov (United States)

    Stoliker, Deborah L.; Campbell, Kate M.; Fox, Patricia M.; Singer, David M.; Kaviani, Nazila; Carey, Minna; Peck, Nicole E.; Barger, John R.; Kent, Douglas B.; Davis, James A.

    2013-01-01

    Extraction techniques utilizing high pH and (bi)carbonate concentrations were evaluated for their efficacy in determining the oxidation state of uranium (U) in reduced sediments collected from Rifle, CO. Differences in dissolved concentrations between oxic and anoxic extractions have been proposed as a means to quantify the U(VI) and U(IV) content of sediments. An additional step was added to anoxic extractions using a strong anion exchange resin to separate dissolved U(IV) and U(VI). X-ray spectroscopy showed that U(IV) in the sediments was present as polymerized precipitates similar to uraninite and/or less ordered U(IV), referred to as non-uraninite U(IV) species associated with biomass (NUSAB). Extractions of sediment containing both uraninite and NUSAB displayed higher dissolved uranium concentrations under oxic than anoxic conditions while extractions of sediment dominated by NUSAB resulted in identical dissolved U concentrations. Dissolved U(IV) was rapidly oxidized under anoxic conditions in all experiments. Uraninite reacted minimally under anoxic conditions but thermodynamic calculations show that its propensity to oxidize is sensitive to solution chemistry and sediment mineralogy. A universal method for quantification of U(IV) and U(VI) in sediments has not yet been developed but the chemical extractions, when combined with solid-phase characterization, have a narrow range of applicability for sediments without U(VI).

  20. Original Inventions based on Chemical scaffolds and electro-physical activity-derived biosimilars interacting with specialties in biology yielding platforms for analysis in virology and antiviral compounds

    Directory of Open Access Journals (Sweden)

    Yamaji N

    2014-11-01

    Full Text Available Background: Original inventions in developing countries, in terms of number of patents filed, granted and that are taken to useful applications as well as in terms of publications of high impact remain relatively lower [1,2] compared to that of developed nations. The reasons could be attributed to lack of importance given to basic research in funding, the number of institutes involved, limited technical support or expertise available etc [1]. Though such initiatives may take a long time to yield fruits, one of the parallel steps we considered worth was to take the original inventions from Japan, born out of basic research in one field, taken through an application-oriented inter disciplinary interactive research in healthcare, thereby paving way for novel solutions. Thus was conceived, the Inventions- Inter-Disciplinary Interactions and Solutions (IIDIAS, an academic session as a part of the one-day International stem cell meet organized every year in the month of October by Nichi-In Centre for Regenerative Medicine (NCRM, an academic Institute based in Chennai, India. In the IIDIAS session, based on original invention(s presented as a prelude in brief, original interdisciplinary interactive research work based on the original invention by NCRM and/or its collaborators are presented by the faculty of the relevant institute. That will be followed by an interactive session in which the potential solutions based on the above accomplishments would be discussed. The IIDIAS session 2014 was based on the following two inventions: A bio-film-based biosimilar invented by an electro-physicist A unique polymer invented by a chemical engineer Inventions and Interdisciplinary Interactions: Invention –I: The bio-film-based biosimilar invented by an electro-physicist: An electro physicist with the Kyoto University, Japan, Dr Nobuyuki Yamaji observed during his experiments that plants and mammalian tissues secrete a layer of fluid after getting hit by

  1. Mass Spectrometric Determination of Chemical Warfare Agents in Indoor Sample Media Typically Collected During Forensic Investigations

    National Research Council Canada - National Science Library

    D'Agostino, P. A; Hancock, J. R; Chenier, C. L

    2005-01-01

    .... DRDC Suffield, in collaboration with the Royal Canadian Mounted Police, identified a need for analytical methods for chemical warfare agent identification in media, including flooring, wall surfaces...

  2. X-ray spectral determination of chemical state of phosphorus and sulfur in anodic oxide films on niobium

    International Nuclear Information System (INIS)

    Bokij, L.P.; Kostikov, Yu.P.

    1989-01-01

    Chemical forms of phosphorus and sulfur in niobium oxide anodic film, obtained by electrochemical technique using niobium in H 2 SO 4 and H 3 PO 4 aqueous solutions, are determined using data on chemical shifts of X-ray emission lines. Films represent Nb 2 O 5(1-γ) (SO 4 ) 5γ and Nb 2 O 5(1-γ) (PO 4 ) 10γ/3 (γ -share of oxygen substituted by acid anion) composition oxosalts. Electrolyte role in formation of niobium anodic oxide structure and effect of phosphorus and sulfur compounds on anodic film conductivity are determined

  3. An approach to the determination of physical-chemical limits of energy consumption for the transition to a stationary state

    International Nuclear Information System (INIS)

    Zimen, K.E.

    1975-02-01

    The paper gives a model of energy consumption and a programme for its application. Previous models are mainly criticized on the grounds that new technological developments as well as adjustments due to learning processes of homo sapiens are generally not sufficiently accounted for in these models. The approach of this new model is therefore an attempt at the determination of the physical-chemical limiting values for the capacity of the global HST (homo sapiens - Tellus) system or of individual regions with respect to certain critical factors. These limiting values determined by the physical-chemical system of the earth are independent of human ingenuity and flexibility. (orig./AK) [de

  4. Rendimentos do processamento e composição química de filés de surubim cultivado em tanques-rede Processing yield and chemical composition of fillets of surubim reared in net cages

    Directory of Open Access Journals (Sweden)

    Denilson Burkert

    2008-07-01

    three replicates. Five surubim fishes weighing from 1280 to 1340g were selected from each cage and unsensibilized and slaughtered for posterior determination of the processing yields of carcass with and without skin, head, total fillet, lateral and abdominal fillets, liver, skin and skeleton. Samples of lateral and abdominal fillets were colleted to determine their chemical analyses. No differences were observed between sexes for the principal processing yields, in a total of 22 females and 23 males. There was difference in the abdominal fillet and of the residues with and without skin among diets. There was difference in the abdominal fillet and of the residues with and without skin among diets. The use of different commercial diets during the raising period did not affect the amount and quality of principal edible cuts of surubim fish.

  5. Methods for the Determination of Chemical Contaminants in Drinking Water. Training Manual.

    Science.gov (United States)

    Office of Water Program Operations (EPA), Cincinnati, OH. National Training and Operational Technology Center.

    This training manual, intended for chemists and technicians with little or no experience in chemical procedures required to monitor drinking water, covers analytical methods for inorganic and organic chemical contaminants listed in the interim primary drinking water regulations. Topics include methods for heavy metals, nitrate, and organic…

  6. Using solid phase micro extraction to determine salting-out (Setschenow) constants for hydrophobic organic chemicals.

    NARCIS (Netherlands)

    Jonker, M.T.O.; Muijs, B.

    2010-01-01

    With increasing ionic strength, the aqueous solubility and activity of organic chemicals are altered. This so-called salting-out effect causes the hydrophobicity of the chemicals to be increased and sorption in the marine environment to be more pronounced than in freshwater systems. The process can

  7. A Quantitative Method to Determine Preservice Chemistry Teachers' Perceptions of Chemical Representations

    Science.gov (United States)

    Head, M. L.; Yoder, K.; Genton, E.; Sumperl, J.

    2017-01-01

    Chemical representations serve as a cornerstone to guide the teaching of chemistry concepts. The influence that a chemical representation has on instruction is largely dependent on how well the viewer interprets the information in the representation. Teachers serve as a guide to the students as they point out and make connections between the…

  8. Incremental Yield of Including Determine-TB LAM Assay in Diagnostic Algorithms for Hospitalized and Ambulatory HIV-Positive Patients in Kenya.

    Science.gov (United States)

    Huerga, Helena; Ferlazzo, Gabriella; Bevilacqua, Paolo; Kirubi, Beatrice; Ardizzoni, Elisa; Wanjala, Stephen; Sitienei, Joseph; Bonnet, Maryline

    2017-01-01

    Determine-TB LAM assay is a urine point-of-care test useful for TB diagnosis in HIV-positive patients. We assessed the incremental diagnostic yield of adding LAM to algorithms based on clinical signs, sputum smear-microscopy, chest X-ray and Xpert MTB/RIF in HIV-positive patients with symptoms of pulmonary TB (PTB). Prospective observational cohort of ambulatory (either severely ill or CD4<200cells/μl or with Body Mass Index<17Kg/m2) and hospitalized symptomatic HIV-positive adults in Kenya. Incremental diagnostic yield of adding LAM was the difference in the proportion of confirmed TB patients (positive Xpert or MTB culture) diagnosed by the algorithm with LAM compared to the algorithm without LAM. The multivariable mortality model was adjusted for age, sex, clinical severity, BMI, CD4, ART initiation, LAM result and TB confirmation. Among 474 patients included, 44.1% were severely ill, 69.6% had CD4<200cells/μl, 59.9% had initiated ART, 23.2% could not produce sputum. LAM, smear-microscopy, Xpert and culture in sputum were positive in 39.0% (185/474), 21.6% (76/352), 29.1% (102/350) and 39.7% (92/232) of the patients tested, respectively. Of 156 patients with confirmed TB, 65.4% were LAM positive. Of those classified as non-TB, 84.0% were LAM negative. Adding LAM increased the diagnostic yield of the algorithms by 36.6%, from 47.4% (95%CI:39.4-55.6) to 84.0% (95%CI:77.3-89.4%), when using clinical signs and X-ray; by 19.9%, from 62.2% (95%CI:54.1-69.8) to 82.1% (95%CI:75.1-87.7), when using clinical signs and microscopy; and by 13.4%, from 74.4% (95%CI:66.8-81.0) to 87.8% (95%CI:81.6-92.5), when using clinical signs and Xpert. LAM positive patients had an increased risk of 2-months mortality (aOR:2.7; 95%CI:1.5-4.9). LAM should be included in TB diagnostic algorithms in parallel to microscopy or Xpert request for HIV-positive patients either ambulatory (severely ill or CD4<200cells/μl) or hospitalized. LAM allows same day treatment initiation in patients at

  9. Drop drying on surfaces determines chemical reactivity - the specific case of immobilization of oligonucleotides on microarrays

    Science.gov (United States)

    2013-01-01

    Background Drop drying is a key factor in a wide range of technical applications, including spotted microarrays. The applied nL liquid volume provides specific reaction conditions for the immobilization of probe molecules to a chemically modified surface. Results We investigated the influence of nL and μL liquid drop volumes on the process of probe immobilization and compare the results obtained to the situation in liquid solution. In our data, we observe a strong relationship between drop drying effects on immobilization and surface chemistry. In this work, we present results on the immobilization of dye labeled 20mer oligonucleotides with and without an activating 5′-aminoheptyl linker onto a 2D epoxysilane and a 3D NHS activated hydrogel surface. Conclusions Our experiments identified two basic processes determining immobilization. First, the rate of drop drying that depends on the drop volume and the ambient relative humidity. Oligonucleotides in a dried spot react unspecifically with the surface and long reaction times are needed. 3D hydrogel surfaces allow for immobilization in a liquid environment under diffusive conditions. Here, oligonucleotide immobilization is much faster and a specific reaction with the reactive linker group is observed. Second, the effect of increasing probe concentration as a result of drop drying. On a 3D hydrogel, the increasing concentration of probe molecules in nL spotting volumes accelerates immobilization dramatically. In case of μL volumes, immobilization depends on whether the drop is allowed to dry completely. At non-drying conditions, very limited immobilization is observed due to the low oligonucleotide concentration used in microarray spotting solutions. The results of our study provide a general guideline for microarray assay development. They allow for the initial definition and further optimization of reaction conditions for the immobilization of oligonucleotides and other probe molecule classes to different

  10. 40 CFR 350.18 - Release of chemical identity determined to be non-trade secret; notice of intent to release...

    Science.gov (United States)

    2010-07-01

    ... determined to be non-trade secret; notice of intent to release chemical identity. 350.18 Section 350.18... INFORMATION: AND TRADE SECRET DISCLOSURES TO HEALTH PROFESSIONALS Trade Secrecy Claims § 350.18 Release of chemical identity determined to be non-trade secret; notice of intent to release chemical identity. (a...

  11. Functional Fit Evaluation to Determine Optimal Ease Requirements in Canadian Forces Chemical Protective Gloves

    National Research Council Canada - National Science Library

    Tremblay-Lutter, Julie

    1995-01-01

    A functional fit evaluation of the Canadian Forces (CF) chemical protective lightweight glove was undertaken in order to quantify the amount of ease required within the glove for optimal functional fit...

  12. Chemical sensors in natural water: peculiarities of behaviour of chalcogenide glass electrodes for determination of copper, lead and cadmium ions

    International Nuclear Information System (INIS)

    Seleznev, B.L.; Legin, A.V.; Vlasov, Yu.G.

    1996-01-01

    Specific features of chemical sensors (chalcogenide glass and crystal ion-selective electrodes) behaviour have been studied to determine copper (2), lead, cadmium and fluorine in the course of in situ measurements, including long-term uninterrupted testing, for solving the problem of inspection over natural water contamination. 16 refs., 3 figs., 2 tabs

  13. Determination of Students' Alternative Conceptions about Chemical Equilibrium: A Review of Research and the Case of Turkey

    Science.gov (United States)

    Ozmen, Haluk

    2008-01-01

    This study aims to determine prospective science student teachers' alternative conceptions of the chemical equilibrium concept. A 13-item pencil and paper, two-tier multiple choice diagnostic instrument, the Test to Identify Students' Alternative Conceptions (TISAC), was developed and administered to 90 second-semester science student teachers…

  14. Use of the nonsteady monotonic heating method for complex determination of thermophysical properties of chemically reacting mixture in the case of non-equilibrium proceeding of the chemical reaction

    International Nuclear Information System (INIS)

    Serebryanyj, G.Z.

    1984-01-01

    Theoretical analysis is made for the monotonic heating method as applied for complex determination of thermophysical properties of chemically reacting gases. The possibility is shown of simultaneous determination of frozen and equilibrium heat capacity, frozen and equilibrium heat conduction provided non-equilibrium occuring of the reaction in the wide range of temperatures and pressures. The monotonic heating method can be used for complex determination of thermophysical properties of chemically reacting systems in case of non-equilibrium proceeding of the chemical reaction

  15. Microplate-Based Evaluation of the Sugar Yield from Giant Reed, Giant Miscanthus and Switchgrass after Mild Chemical Pre-Treatments and Hydrolysis with Tailored Trichoderma Enzymatic Blends.

    Science.gov (United States)

    Cianchetta, Stefano; Bregoli, Luca; Galletti, Stefania

    2017-11-01

    Giant reed, miscanthus, and switchgrass are considered prominent lignocellulosic feedstocks to obtain fermentable sugars for biofuel production. The bioconversion into sugars requires a delignifying pre-treatment step followed by hydrolysis with cellulase and other accessory enzymes like xylanase, especially in the case of alkali pre-treatments, which retain the hemicellulose fraction. Blends richer in accessory enzymes than commercial mix can be obtained growing fungi on feedstock-based substrates, thus ten selected Trichoderma isolates, including the hypercellulolytic strain Trichoderma reesei Rut-C30, were grown on giant reed, miscanthus, or switchgrass-based substrates. The produced enzymes were used to saccharify the corresponding feedstocks, compared to a commercial enzymatic mix (6 FPU/g). Feedstocks were acid (H 2 SO 4 0.2-2%, w/v) or alkali (NaOH 0.02-0.2%, w/v) pre-treated. A microplate-based approach was chosen for most of the experimental steps due to the large number of samples. The highest bioconversion was generally obtained with Trichoderma harzianum Or4/99 enzymes (78, 89, and 94% final sugar yields at 48 h for giant reed, miscanthus, and switchgrass, respectively), with significant increases compared to the commercial mix, especially with alkaline pre-treatments. The differences in bioconversion yields were only partially caused by xylanases (maximum R 2  = 0.5), indicating a role for other accessory enzymes.

  16. Evaluation of Induced Mutants Using Irradiation and Chemical Mutagen in Lupin (Lupinus albus L.) for Earliness and Yield and Its Components

    International Nuclear Information System (INIS)

    Ragsb, A.I.; Boshra, S. A.; Mehany, A. L.; Darwish, A. A.; Khattab, M. M.

    2007-01-01

    This study was conducted in 2001 / 2002, 2002 /2003 and 2003/ 2004 seasons at the Experimental Farm of Nuclear Res. Center, Inshas. The objectives were to evaluate 23 induced mutants with gamma rays and EMS and two local cultivars Giza 1 and Giza 2 in the three generations (M3, M4, and M5) for earliness and seed yield and its components. The results were: It was found that earliness was observed for mutants 5, 11, 17, 21 and 22 as compared with Giza 1 and Giza 2 in the three generations with a maximum value of 19 days earlier than Giza 2. Highly significant increase for number of pods / plant was found for mutants 8, 15 and 19 as compared with the two local cultivars in the three generations. A considerable increase for no of seeds/plant was noticed only for mutant lines 8 and 15 as compared with the two local cultivars. A remarkable increase for seed index was only found for mutant lines 6, 12 and 21 as compared with the two local cultivars in the three generations. A considerable increase for seed yield / plant was revealed for mutant lines 1, 4, 7, 8, 15 and 19 as compared with the two local cultivars in the three generations.

  17. Use of 99mTc from a commercial 99Mo/9mTc generator as yield tracer for the determination of 99Tc at low levels

    DEFF Research Database (Denmark)

    Hou, Xiaolin; Jensen, Mikael; Nielsen, Sven Poul

    2007-01-01

    The concentrations of Tc-99 and impurity radionuclides in the Tc-99m tracer solution obtained from a commercial Mo-99/Tc-99m generator were measured by gamma spectrometry and liquid scintillation counting. Mo-99 and Ru-103 were found in the Tc-99m eluate. A simple separation using two extra alumina...... cartridges was investigated to purify the eluate to obtain a suitable Tc-99m tracer with low Tc-99 concentration. The activity ratio of Tc-99/Tc-99m in the prepared Tc-99m solution is lower than 15 x 10(-9), which is higher than the theoretical ratio of less than 10 x 10(-9). The possible reason is discussed....... The Tc-99 in the 20 kBq spiked Tc-99m tracer was found to be less than 0.3mBq, which is lower than the detection limit of the radiometric method used for environmental samples. The purified Tc-99m eluate is used as yield tracer for the determination of low levels of Tc-99 in environmental samples. (c...

  18. The importance of local factors and management in determining wheat yield variability in on-farm experimentation in Tigray, northern Ethiopia

    NARCIS (Netherlands)

    Kraaijvanger, R.; Veldkamp, A.

    2015-01-01

    Low crop yield in Tigray is one of the causes of food insecurity. Intervention work to increase yields, however, had only limited success and farmers often hesitated to adopt recommended practices. Considering this, we used participatory on-farm experimentation to arrive at best practices

  19. Determining

    Directory of Open Access Journals (Sweden)

    Bahram Andarzian

    2015-06-01

    Full Text Available Wheat production in the south of Khuzestan, Iran is constrained by heat stress for late sowing dates. For optimization of yield, sowing at the appropriate time to fit the cultivar maturity length and growing season is critical. Crop models could be used to determine optimum sowing window for a locality. The objectives of this study were to evaluate the Cropping System Model (CSM-CERES-Wheat for its ability to simulate growth, development, grain yield of wheat in the tropical regions of Iran, and to study the impact of different sowing dates on wheat performance. The genetic coefficients of cultivar Chamran were calibrated for the CSM-CERES-Wheat model and crop model performance was evaluated with experimental data. Wheat cultivar Chamran was sown on different dates, ranging from 5 November to 9 January during 5 years of field experiments that were conducted in the Khuzestan province, Iran, under full and deficit irrigation conditions. The model was run for 8 sowing dates starting on 25 October and repeated every 10 days until 5 January using long-term historical weather data from the Ahvaz, Behbehan, Dezful and Izeh locations. The seasonal analysis program of DSSAT was used to determine the optimum sowing window for different locations as well. Evaluation with the experimental data showed that performance of the model was reasonable as indicated by fairly accurate simulation of crop phenology, biomass accumulation and grain yield against measured data. The normalized RMSE were 3%, 2%, 11.8%, and 3.4% for anthesis date, maturity date, grain yield and biomass, respectively. Optimum sowing window was different among locations. It was opened and closed on 5 November and 5 December for Ahvaz; 5 November and 15 December for Behbehan and Dezful;and 1 November and 15 December for Izeh, respectively. CERES-Wheat model could be used as a tool to evaluate the effect of sowing date on wheat performance in Khuzestan conditions. Further model evaluations

  20. Quantum-chemical calculations of the metallofullerene yields in the X@C{sub 74}, L@C{sub 74}, and Z@C{sub 82} series

    Energy Technology Data Exchange (ETDEWEB)

    Uhlík, Filip [Faculty of Science, Charles University in Prague, Albertov 6, 128 43 Prague 2 (Czech Republic); Slanina, Zdeněk; Nagase, Shigeru [Department of Theoretical Molecular Science, Institute for Molecular Science, Myodaiji, Okazaki 444-8585, Aichi (Japan)

    2015-01-22

    The contribution reports computations for Al@C{sub 82}, Sc@C{sub 82}, Y@C{sub 82} and La@C{sub 82} based on encapsulation into the IPR (isolated pentagon rule) C{sub 2ν} C{sub 82} cage and also on Mg@C{sub 74}, Ca@C{sub 74}, Sr@C{sub 74} and Ba@C{sub 74} based on encapsulation into the only C{sub 74} IPR cage as well as for three selected lanthanoids La@C{sub 74}, Yb@C{sub 74}, and Lu@C{sub 74}. Their structural and energetic characteristics are used for evaluations of the relative production yields, using the encapsulation Gibbs-energy and saturated metal pressures. It is shown that the results can be well related to the ionization potentials of the free metal atoms.

  1. Determination of trace amounts of chemical warfare agent degradation products in decontamination solutions with NMR spectroscopy.

    Science.gov (United States)

    Koskela, Harri; Rapinoja, Marja-Leena; Kuitunen, Marja-Leena; Vanninen, Paula

    2007-12-01

    Decontamination solutions are used for an efficient detoxification of chemical warfare agents (CWAs). As these solutions can be composed of strong alkaline chemicals with hydrolyzing and oxidizing properties, the analysis of CWA degradation products in trace levels from these solutions imposes a challenge for any analytical technique. Here, we present results of application of nuclear magnetic resonance spectroscopy for analysis of trace amounts of CWA degradation products in several untreated decontamination solutions. Degradation products of the nerve agents sarin, soman, and VX were selectively monitored with substantially reduced interference of background signals by 1D 1H-31P heteronuclear single quantum coherence (HSQC) spectrometry. The detection limit of the chemicals was at the low part-per-million level (2-10 microg/mL) in all studied solutions. In addition, the concentration of the degradation products was obtained with sufficient confidence with external standards.

  2. Determination of chemical form of iodine with IC-ICP-MS system and its application to the environmental samples

    International Nuclear Information System (INIS)

    Yoshida, S.; Katou, S.; Sekimoto, H.; Muramatsu, Y.

    2005-01-01

    Iodine-129 is one of the important radionuclides possibly released into the environment from nuclear weapons testing and from the nuclear facilities such as nuclear fuel reprocessing plants. Because of its long half-life (1.57 x 10 7 y), knowing its long-term behavior in the environment is a major concern. As I-129 is expected to act together with stable iodine (I-127) in the environment after long time, the biogeochemical cycling of stable iodine in the environment can be used for the reliable safety assessment of I-129. Chemical form is the one of the important factors controlling the 'iodine behavior in the environment. Iodide (I - ) and iodate (IO 3 - ) are known to be the major chemical form in the aqueous solution. However, the information on the chemical form of iodine in the environmental sample is limited because of lack of reliable analytical technique for trace level of iodine in the environment. In this study, the analytical system by using ion chromatograph (IC) followed by inductively coupled plasma mass spectrometry (ICP-MS) was developed for the separate determination of I - and IO 3 - in the aqueous solution. The IC with anion exchange column (EXCELPAK ICS-A23) was used for the separation of I - and IO 3 - with 30 mM (NH 4 ) 2 CO 3 as eluent. Separated iodine was determined with ICP-MS on line. with the detection limit 0.1 - 1 μg/L. The total iodine concentration was also measured by the direct determination with ICP-MS. The iodine in the several environmental samples such as irrigation water in paddy field was successfully determined with information of chemical form. In incubation experiment with flooded soil, the change of the chemical form of iodine in the soil solution with change of Eh was observed. Detailed data will be discussed in the presentation.

  3. Sorptive capacities of lipids determined by passive dosing of non-polar organic chemicals

    DEFF Research Database (Denmark)

    Jahnke, Annika; Kierkegaard, Amelie; Bolinius, Damien

    VMS), chlorobenzenes and polychlorinated biphenyls via a common headspace over an olive oil donor phase to transfer the same chemical activity into the samples; iii) sampling of EOM and olive oil controls at different time points; iv) purge-and-trap extraction of the model chemicals onto ENV+ SPE cartridges, elution...... and GC/MS analysis; v) characterization of the lipid composition in all samples via NMR. Our experiments demonstrate that the sorptive capacities of the EOM samples do not differ significantly from the olive oil controls if the EOM consists of neutral lipids only. However, the EOM samples show small...

  4. Model nebulae and determination of the chemical composition of the Magellanic Clouds.

    Science.gov (United States)

    Aller, L H; Keyes, C D; Czyzak, S J

    1979-04-01

    An analysis of previously presented photoelectric spectrophotometry of HII regions (emission-line diffuse nebulae) in the two Magellanic Clouds is carried out with the aid of theoretical nebular models, which are used primarily as interpolation devices. Some advantages and limitations of such theoretical models are discussed. A comparison of the finally obtained chemical compositions with those found by other observers shows generally a good agreement, suggesting that it is possible to obtain reliable chemical compositions from low excitation gaseous nebulae in our own galaxy as well as in distant stellar systems.

  5. SLIFER measurement for explosive yield

    International Nuclear Information System (INIS)

    Bass, R.C.; Benjamin, B.C.; Miller, H.M.; Breding, D.R.

    1976-04-01

    This report describes the shorted location indicator by frequency of electrical resonance (SLIFER) system used at Sandia Laboratories for determination of explosive yield of under ground nuclear tests

  6. Development and application of Darwin X-ray diffraction theory for structure and chemical composition determination in multilayered crystals

    International Nuclear Information System (INIS)

    Wojcik, M.; Gaca, J.; Turos, A.; Strupinski, W.

    2000-01-01

    The method of investigation of the chemical composition for quaternary heterostructures has been developed. To this end X-ray high resolution diffractometry and RBS methods were applied. This method consists in finding a best fit between experimental diffraction pattern and theoretical one calculated, employing Darwin dynamical diffraction theory for a given model of heterostructure. This procedure was applied to determine the chemical profile in the growth direction for InGaAsP/InP superlattices that were grown by MOCVD technology on 001 InP substrate. The relations between the chemical composition of In x Ga 1-x As y P 1-y layer, its lattice parameter, optoelectronic properties and growth conditions were found. (author)

  7. Determination of the Ubiquitin Fitness Landscape under Seventeen Chemical Conditions in a Classroom Setting

    Science.gov (United States)

    Mavor, David Carl

    2017-01-01

    Ubiquitin is essential for eukaryotic life and varies in only 3 amino acid positions between yeast and humans. However, recent deep sequencing studies indicate that ubiquitin is highly tolerant to single mutations. We hypothesized that this tolerance would be reduced by chemically induced physiologic perturbations. To test this hypothesis, a class…

  8. Mechanisms of chemical generation of volatile hydrides for trace element determination (IUPAC Technical Report)

    Czech Academy of Sciences Publication Activity Database

    D'Ulivo, A.; Dědina, Jiří; Mester, Z.; Sturgeon, R. E.; Wang, Q.; Welz, B.

    2011-01-01

    Roč. 83, č. 6 (2011), s. 1283-1340 ISSN 0033-4545 Institutional research plan: CEZ:AV0Z40310501 Keywords : borane complexes * chemical generation of volatile hydrides (CHG) * volatile hydrides Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 2.789, year: 2011

  9. The effects of castration on the growth parameters, carcass yield and meat chemical composition of intensively reared Common Pheasant (Phasianus colchicus colchicus L.

    Directory of Open Access Journals (Sweden)

    Renata Baric-Rafaj

    2010-01-01

    Full Text Available The effects of castration on growth performance, carcass characteristics and chemical composition of m. iliotibilais cranialis and m. pectoralis superficialis of pheasants were examined. Forty pheasants reared in commercial pheasantry were included in the experiment. Half of the pheasants were castrated at 8 weeks of age. Values for live weight tended to be higher in castrated pheasants in the 24th week (P<0.1 and values for weight gain were significantly higher between the 16th and 24th weeks (P<0.05. Feed-to-gainratio (8th – 32nd week was significantly better (P<0.05 in castrated pheasants. Eviscerated weight and dressing percentage at 32nd week were not significantly different between treatments. The chemical composition of m. iliotibilais cranialis and m. pectoralis superficialis showed significantly higher values of fat (P<0.01 and moisture (P<0.05 in castrated pheasants in comparison with intact ones. Protein content of both muscles was higher in intact pheasants (P<0.05. Body part weights were not influenced by the treatment with the exception of heart weight, which was significantly higher in the intact pheasants (P<0.05. We concluded that castration tended to improve growth performance only in the first 24 weeks of the fattening period and, therefore, continuation of fattening after that period is no longer feasible. The most important characteristic of the castrated pheasant’s meat was an increased amount of fat. More studies under different feeding and alternative breeding systems are necessary to improve production.

  10. Effect of lime, N, P, and K amendments to surface-mined coal spoils on yield and chemical composition of common Bermuda grass

    Energy Technology Data Exchange (ETDEWEB)

    Ebelhar, M W; Barnhisel, R I; Akin, G W; Powell, J L

    1982-12-01

    Common Bermuda grass (Cynodon dactylon, L. Pers.) was used as an alternative to cool-season grasses such as tall fescue (Festuca arundinacea Schreb.) on acid sandstone surface-mine spoils in western Kentucky. Lime, N, P, and K fertilizer amendments were evaluated as to their effects in promoting Bermuda grass growth and development. The applied lime was effective in raising the pH from 3.4 to 4.6, 5.7, and 6.3 for the 18, 36 and 72 metric ton/ha treatments, respectively, over a 17-month period. Nitrogen was found to affect Bermuda grass production significantly and severe deficiency symptoms were observed where N was not applied. Dry matter yields increased significantly with each additional increment of N applied. Although the application of P and K increased the concentration of these ions in the plant tissues, the main influence of P and K was to increase the plants' resistance to winter killing; little effect on total dry matter production was observed. 19 references.

  11. A Single Transcriptome of a Green Toad (Bufo viridis Yields Candidate Genes for Sex Determination and -Differentiation and Non-Anonymous Population Genetic Markers.

    Directory of Open Access Journals (Sweden)

    Jörn F Gerchen

    Full Text Available Large genome size, including immense repetitive and non-coding fractions, still present challenges for capacity, bioinformatics and thus affordability of whole genome sequencing in most amphibians. Here, we test the performance of a single transcriptome to understand whether it can provide a cost-efficient resource for species with large unknown genomes. Using RNA from six different tissues from a single Palearctic green toad (Bufo viridis specimen and Hiseq2000, we obtained 22,5 Mio reads and publish >100,000 unigene sequences. To evaluate efficacy and quality, we first use this data to identify green toad specific candidate genes, known from other vertebrates for their role in sex determination and differentiation. Of a list of 37 genes, the transcriptome yielded 32 (87%, many of which providing the first such data for this non-model anuran species. However, for many of these genes, only fragments could be retrieved. In order to allow also applications to population genetics, we further used the transcriptome for the targeted development of 21 non-anonymous microsatellites and tested them in genetic families and backcrosses. Eleven markers were specifically developed to be located on the B. viridis sex chromosomes; for eight markers we can indeed demonstrate sex-specific transmission in genetic families. Depending on phylogenetic distance, several markers, which are sex-linked in green toads, show high cross-amplification success across the anuran phylogeny, involving nine systematic anuran families. Our data support the view that single transcriptome sequencing (based on multiple tissues provides a reliable genomic resource and cost-efficient method for non-model amphibian species with large genome size and, despite limitations, should be considered as long as genome sequencing remains unaffordable for most species.

  12. Moisture content prediction in poultry litter using artificial intelligence techniques and Monte Carlo simulation to determine the economic yield from energy use.

    Science.gov (United States)

    Rico-Contreras, José Octavio; Aguilar-Lasserre, Alberto Alfonso; Méndez-Contreras, Juan Manuel; López-Andrés, Jhony Josué; Cid-Chama, Gabriela

    2017-11-01

    The objective of this study is to determine the economic return of poultry litter combustion in boilers to produce bioenergy (thermal and electrical), as this biomass has a high-energy potential due to its component elements, using fuzzy logic to predict moisture and identify the high-impact variables. This is carried out using a proposed 7-stage methodology, which includes a statistical analysis of agricultural systems and practices to identify activities contributing to moisture in poultry litter (for example, broiler chicken management, number of air extractors, and avian population density), and thereby reduce moisture to increase the yield of the combustion process. Estimates of poultry litter production and heating value are made based on 4 different moisture content percentages (scenarios of 25%, 30%, 35%, and 40%), and then a risk analysis is proposed using the Monte Carlo simulation to select the best investment alternative and to estimate the environmental impact for greenhouse gas mitigation. The results show that dry poultry litter (25%) is slightly better for combustion, generating 3.20% more energy. Reducing moisture from 40% to 25% involves considerable economic investment due to the purchase of equipment to reduce moisture; thus, when calculating financial indicators, the 40% scenario is the most attractive, as it is the current scenario. Thus, this methodology proposes a technology approach based on the use of advanced tools to predict moisture and representation of the system (Monte Carlo simulation), where the variability and uncertainty of the system are accurately represented. Therefore, this methodology is considered generic for any bioenergy generation system and not just for the poultry sector, whether it uses combustion or another type of technology. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. Determining the sputter yields of molybdenum in low-index crystal planes via electron backscattered diffraction, focused ion beam and atomic force microscope

    Energy Technology Data Exchange (ETDEWEB)

    Huang, H.S., E-mail: 160184@mail.csc.com.tw [New Materials Research and Development Department, China Steel Corporation, 1 Chung Kang Road, Hsiao Kang, Kaohsiung 812, Taiwan, ROC (China); Chiu, C.H.; Hong, I.T.; Tung, H.C. [New Materials Research and Development Department, China Steel Corporation, 1 Chung Kang Road, Hsiao Kang, Kaohsiung 812, Taiwan, ROC (China); Chien, F.S.-S. [Department of Physics, Tunghai University, 1727, Sec. 4, Xitun Dist., Taiwan Boulevard, Taichung 407, Taiwan, ROC (China)

    2013-09-15

    Previous literature has used several monocrystalline sputtering targets with various crystalline planes, respectively, to investigate the variations of the sputter yield of materials in different crystalline orientations. This study presents a method to measure the sputtered yields of Mo for the three low-index planes (100), (110), and (111), through using an easily made polycrystalline target. The procedure was firstly to use electron backscattered diffraction to identify the grain positions of the three crystalline planes, and then use a focused ion beam to perform the micro-milling of each identified grain, and finally the sputter yields were calculated from the removed volumes, which were measured by atomic force microscope. Experimental results showed that the sputter yield of the primary orientations for Mo varied as Y{sub (110)} > Y{sub (100)} > Y{sub (111)}, coincidental with the ranking of their planar atomic packing densities. The concept of transparency of ion in the crystalline substance was applied to elucidate these results. In addition, the result of (110) orientation exhibiting higher sputter yield is helpful for us to develop a Mo target with a higher deposition rate for use in industry. By changing the deformation process from straight rolling to cross rolling, the (110) texture intensity of the Mo target was significantly improved, and thus enhanced the deposition rate. - Highlights: • We used EBSD, FIB and AFM to measure the sputter yields of Mo in low-index planes. • The sputter yield of the primary orientations for Mo varied as Y{sub (110)} > Y{sub (100)} > Y{sub (111)}. • The transparency of ion was used to elucidate the differences in the sputter yield. • We improved the sputter rate of polycrystalline Mo target by adjusting its texture.

  14. DETERMINING LIGHTFASTNESS PROPERTIES OF VEGETABLE TANNINS AND CHEMICAL PROPERTIES OF THE LEATHERS TANNED WITH MODIFIED MIMOSA AND QUEBRACHO

    Directory of Open Access Journals (Sweden)

    OMUR Sukru

    2016-05-01

    Full Text Available The vegetable tannins are the oldest tanning agents used in leather industry. They give their natural character and colour to the leathers which they are applied to, but they have the disadvantage of colour change when they are exposed to light for prolonged times. In this study light fastness properties of leathers tanned with mimosa, quebracho, valonea and chestnut tannins were measured. Lightfastness properties of mimosa and quebracho tannins were found lower. Then these tannins were modified with sulphitation, novalac synthesis and sulphomethylation processes. Lightfastness and determination of volatile matter, determination of matter soluble in dichloromethane, determination of sulphated total ash and sulphated water-insoluble ash, determination of water soluble matter, water soluble inorganic matter and water soluble organic matter, determination of nitrogen content and hide substance, calculation of degree of tannage determination of formaldehyde content analyses were performed to the leathers tanned with modified mimosa and quebracho tannins. From comparison of results, it was understood that sulpmethylation process can be used for production of leathers with higher lightfastness and without major change on chemical properties. When chemical properties of leathers tanned with modified quebracho and mimosa are considered: volatile matter, sulphated total ash and sulphated water- insoluble ash, water soluble matter, water soluble inorganic matter and water soluble organic matter, hide substance and formaldehyde contents were found compatible with standard mimosa and quebracho. However degree of tannage and matter soluble in dichloromethane values were found lower, which means some enhancements in modification or fatliquoring process should be considered.

  15. Ion-stimulated Gas Desorption Yields of Electropolished, Chemically Etched, and Coated (Au, Ag, Pd, TiZrV) Stainless Steel Vacuum Chambers and St707 Getter Strips Irradiated with 4.2 MeV/u lead ions

    CERN Document Server

    Mahner, E; Küchler, D; Malabaila, M; Taborelli, M

    2005-01-01

    The ion-induced desorption experiment, installed in the CERN Heavy Ion Accelerator LINAC 3, has been used to measure molecular desorption yields for 4.2 MeV/u lead ions impacting under grazing incidence on different accelerator-type vacuum chambers. Desorption yields for H2, CH4, CO, and CO2, which are of fundamental interest for future accelerator applications, are reported for different stainless steel surface treatments. In order to study the effect of the surface oxide layer on the gas desorption, gold-, silver-, palladium-, and getter-coated 316 LN stainless steel chambers and similarly prepared samples were tested for desorption at LINAC 3 and analysed for chemical composition by X-ray Photoemission Spectroscopy (XPS). The large effective desorption yield of 2 x 104 molecules/Pb53+ ion, previously measured for uncoated, vacuum fired stainless steel, was reduced after noble-metal coating by up to 2 orders of magnitude. In addition, pressure rise measurements, the effectiveness of beam scrubbing with le...

  16. Differential growth and yield by canola (Brassica napus L.) and wheat (Triticum aestivum L.) arising from alterations in chemical properties of sandy soils due to additions of fly ash.

    Science.gov (United States)

    Yunusa, Isa A M; Manoharan, Veeragathipillai; Harris, Rob; Lawrie, Roy; Pal, Yash; Quiton, Jonathan T; Bell, Richard; Eamus, Derek

    2013-03-30

    There is a need for field trials on testing agronomic potential of coal fly ash to engender routine use of this technology. Two field trials were undertaken with alkaline and acidic fly ashes supplied at between 3 and 6 Mg ha⁻¹ to acidic soils and sown to wheat and canola at Richmond (Eastern Australia) and to wheat only at Merredin (Western Australia). Ash addition marginally (PAPSIM at Richmond over a 100-year period (1909-2008) predicted yield increases in 52% of years with addition of ash at 3.0 Mg ha⁻¹ compared with 24% of years with addition of ash at 6.0 Mg ha⁻¹. The simulated yield increases did not exceed 40% over the control with addition of 6 Mg ha⁻¹ ash, but was between 40% and 50% with an addition rate of 3 Mg ha⁻¹. We found no evidence of phytotoxicity in either crop in this unusually dry year and there is still a need for further field assessment in years with favourable rainfall to enable development of clear recommendations on fly ash rates for optimum yield benefits. © 2012 Society of Chemical Industry.

  17. Influence of malaxation time of olive paste on oil extraction yields and chemical and organoleptic characteristics of virgin olive oil obtained by a centrifugal decanter at water saving

    Directory of Open Access Journals (Sweden)

    Serraiocco, A.

    2002-06-01

    Full Text Available Experimental tests were carried out to ascertain the influence of malaxation time of olive paste on extraction yields and qualitative characteristics of virgin olive oils obtained by a centrifugal decanter at water saving. Results show that malaxation time has to be no less than 45 minutes to have a satisfactory oil extraction yield. Furthermore, it was ascertained that the malaxation time, protracted up to 90 minutes, does not have influence upon qualitative and organoleptic characteristics of oils. Only the total phenols content of oils changed significantly when the malaxation time of olive paste increased from 15 to 90 minutes. However, in this research has been demonstrated that in some cases the total phenols content of oils increased during the first 30-45 minutes of malaxation and after it diminished. This is due to the variation of total phenols content of vegetable water that in the first time increased and after diminished very quickly. Because of the partition equilibrium law, the total phenols content of oil changed in the same way. Finally, results show that the composition of volatile substances of head-space of oils did not change increasing the malaxation time of olive paste obtained from good quality olive fruits.Se realizaron pruebas experimentales para verificar la influencia del tiempo de batido sobre los rendimientos en aceite y sobre las características de la calidad de los aceites obtenidos con un decanter centrifugo con ahorro de agua. Los resultados conseguidos indicaron que el tiempo de batido no debe ser inferior a 45 minutos para poder obtener rendimientos en aceite satisfactorios. Además, se pudo verificar que la operación de batido, aun siendo prolongada a 90 minutos, no influencia significativamente en las características cualitativas y organolépticas de los aceites. Solo el contenido de fenoles totales en los aceites disminuyó cuando el tiempo de batido fue incrementado de 15 a 90 minutos. Sin embargo, se

  18. Influence of fat and oil type on the yield, physico-chemical properties, and microstructure of fat, oil, and grease (FOG) deposits.

    Science.gov (United States)

    Del Mundo, Dann Marie N; Sutheerawattananonda, Manote

    2017-11-01

    Fat, oil, and grease (FOG) deposit, in the form of calcium soap, was found to cause sanitary sewer overflows due to its adhesion on pipe walls. To address this problem, laboratory-prepared calcium soaps have been used to investigate the formation mechanisms of FOG deposits. However, the fats and oils previously utilized were limited and some soap characteristics were not examined. This research attempted to probe through the properties of calcium soaps prepared from calcium chloride and the fats and oils of chicken, pork, palm olein, soybean, olive, and coconut to further understand FOG formation and stability. Results revealed that FOG deposits may occur as smooth, paste-like material or coarse, semi-solid substance depending on their exposure to excess fat/oil and calcium. The smooth soaps with more excess fat/oil demonstrated high apparent viscosity and consistency index, while the coarse soaps with large levels of calcium signified higher melting endset. Moreover, a soap microstructure showing evident networks and lesser void area displayed higher heat and rheological stability, respectively. Overall, fats and oils with higher oleic to palmitic acid ratio such as palm olein oil, olive oil, chicken fat, and pork fat produced soaps with greater yield and degree of saponification. Hence, establishments and authorities should be alert in managing and monitoring these wastes. On the other hand, soybean oil high in linoleic acid and coconut oil high in lauric acid do not pose an immediate threat to the sewer system since they only produced soaps in small quantity. However, their soaps showed high melting endset which could pose a serious effect when accumulated at large amount. On the whole, the fatty acid profile of fats and oils, the presence of excess fat/oil, and calcium content mainly dictate the appearance, melting, rheology, and microstructure of calcium soaps. Their distinct properties can be used as criteria in predicting the condition and stability of FOG

  19. Colorimetric sensor array for determination and identification of toxic industrial chemicals.

    Science.gov (United States)

    Feng, Liang; Musto, Christopher J; Kemling, Jonathan W; Lim, Sung H; Zhong, Wenxuan; Suslick, Kenneth S

    2010-11-15

    A low-cost yet highly sensitive colorimetric sensor array for the detection and identification of toxic industrial chemicals (TICs) has been developed. The sensor consists of a disposable array of cross-responsive nanoporous pigments whose colors are changed by diverse chemical interactions with analytes. Clear differentiation among 20 different TICs has been easily achieved at both their IDLH (immediately dangerous to life or health) concentration within 2 min of exposure and PEL (permissible exposure limit) concentration within 5 min of exposure with no errors or misclassifications. Detection limits are generally well below the PEL (in most cases below 5% of PEL) and are typically in the low ppb range. The colorimetric sensor array is not responsive to changes in humidity or temperature over a substantial range. The printed arrays show excellent batch to batch reproducibility and long shelf life (greater than 3 months).

  20. Odour as a determinant of persistent symptoms after a chemical explosion, a longitudinal study

    OpenAIRE

    Tjalvin, Gro; Magerøy, Nils; Bråtveit, Magne; Lygre, Stein Håkon Låstad; Hollund, Bjørg Eli; Moen, Bente Elisabeth

    2017-01-01

    Foul-smelling environmental pollution was a major concern following a chemical workplace explosion. Malodorous pollution has previously been associated with aggravated physical and psychological health, and in persons affected by a trauma, an incidence-related odour can act as a traumatic reminder. Olfaction may even be of significance in the development and persistence of post-traumatic stress symptoms (PTSS). The present longitudinal study assessed whether perceived smell related to malodor...

  1. Determination of physicochemical and optical parameters of xerogel layers for chemical sensing

    Czech Academy of Sciences Publication Activity Database

    Matějec, Vlastimil; Mrázek, Jan; Chomát, Miroslav; Skokánková, Jana; Raileanu, M.; Zaharescu, M.

    2003-01-01

    Roč. 12,3 P.IVSup.(2003), s. 1545-1554 ISSN 1224-9513. [Physical Chemistry Conference ROMPHYSCHEM /11./. Timisoara, 02.09.2003-05.09.2003] R&D Projects: GA ČR(CZ) GA102/02/0779; GA AV ČR(CZ) KSK2067107 Keywords : chemical sensor s * sol-gel processing * aerogels * gases Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering

  2. Construction of an experimental simplified model for determining of flow parameters in chemical reactors, using nuclear techniques

    International Nuclear Information System (INIS)

    Araujo Paiva, J.A. de.

    1981-03-01

    The development of a simplified experimental model for investigation of nuclear techniques to determine the solid phase parameters in gas-solid flows is presented. A method for the measurement of the solid phase residence time inside a chemical reactor of the type utilised in the cracking process of catalytic fluids is described. An appropriate radioactive labelling technique of the solid phase and the construction of an eletronic timing circuit were the principal stages in the definition of measurement technique. (Author) [pt

  3. Chemical compositions of magnetic, stony spherules from deep-sea sediments determined by instrumental neutron activation analysis

    International Nuclear Information System (INIS)

    Yamakoshi, Kazuo

    1984-01-01

    Chemical compositions of magnetic, stony spherules from deep sea sediments were determined by instrumental neutron activation analysis. High Ir, Au, Ni and Co contents indicate their extraterrestrial origin. The obtained compositions are considerably different from those of chondrites. It can be qualitatively interpreted, however, that cosmic matters having the compositions of chondrites are changed into magnetic, stony spherules by thermal degenerations during their atmospheric entry. (author)

  4. PIXE and GC–MS investigation for the determination of the chemical composition of Syrian Cuminum cyminum L

    International Nuclear Information System (INIS)

    Rihawy, M.S.; Bakraji, E.H.; Odeh, A.

    2014-01-01

    The chemical composition and concentration of Syrian cumin (Cuminum cyminum L.) were investigated. The particle-induced X-ray emission (PIXE) analytical technique was used to analyze a wide range of elements from Mg to Sr. The advantages and disadvantages of the PIXE technique in plant material elemental analysis are discussed. A high level of iron was detected in the cumin samples, clarifying the possible contribution of cumin to maintaining the immune system. The contribution of the elements in cumin seeds to the dietary recommended intakes (DRI) of elements was evaluated. Additionally, GC–MS measurements were performed to determine the chemical composition of cumin essential oil. Twenty-one components were identified, and cuminaldehyde, γ-terpinene, o-cymene, limonene and β-pinene were determined to be the major constituents. A correlation between the chemical composition of cumin seeds and their use as a traditional remedy is proposed. - Highlights: • To our knowledge, there is no published studies focus on the Syrian cumin composition (neither elemental nor essential oil components) in spite of its valuable medicinal importance in the country. • This work is basically dedicated to investigate both elemental content and essential oil component of the Syrian cumin seeds. • The elemental analysis was performed using PIXE, a very powerful elemental analysis technique and the essential oil components were determined using GC–MS

  5. Direct determination of cadmium in Orujo spirit samples by electrothermal atomic absorption spectrometry: Comparative study of different chemical modifiers

    Energy Technology Data Exchange (ETDEWEB)

    Vilar Farinas, M. [Departamento de Quimica Analitica, Nutricion y Bromatologia, Facultad de Ciencias, Universidad de Santiago de Compostela, Campus de Lugo, 27002 Lugo (Spain); Barciela Garcia, J. [Departamento de Quimica Analitica, Nutricion y Bromatologia, Facultad de Ciencias, Universidad de Santiago de Compostela, Campus de Lugo, 27002 Lugo (Spain); Garcia Martin, S. [Departamento de Quimica Analitica, Nutricion y Bromatologia, Facultad de Ciencias, Universidad de Santiago de Compostela, Campus de Lugo, 27002 Lugo (Spain); Pena Crecente, R. [Departamento de Quimica Analitica, Nutricion y Bromatologia, Facultad de Ciencias, Universidad de Santiago de Compostela, Campus de Lugo, 27002 Lugo (Spain); Herrero Latorre, C. [Departamento de Quimica Analitica, Nutricion y Bromatologia, Facultad de Ciencias, Universidad de Santiago de Compostela, Campus de Lugo, 27002 Lugo (Spain)]. E-mail: cherrero@lugo.usc.es

    2007-05-22

    In this work, several analytical methods are proposed for cadmium determination in Orujo spirit samples using electrothermal atomic absorption spectrometry (ETAAS). Permanent chemical modifiers thermally coated on the platforms inserted in pyrolytic graphite tubes (such as W, Ir, Ru, W-Ir and W-Ru) were comparatively studied in relation to common chemical modifier mixtures [Pd-Mg(NO{sub 3}){sub 2} and (NH{sub 4})H{sub 2}PO{sub 4}-Mg(NO{sub 3}){sub 2}] for cadmium stabilization. Different ETAAS Cd determination methods based on the indicated modifiers have been developed. In each case, pyrolysis and atomization temperatures, atomization shapes, characteristic masses and detection limits as well as other analytical characteristics have been determined. All the assayed modifiers (permanent and conventional) were capable of achieving the appropriate stabilization of the analyte, with the exception of Ru and W-Ru. Moreover, for all developed methods, recoveries (99-102%) and precision (R.S.D. lower than 10%) were acceptable. Taking into account the analytical performance (best detection limit LOD = 0.01 {mu}g L{sup -1}), the ETAAS method based on the use of W as a permanent modifier was selected for further direct Cd determinations in Orujo samples from Galicia (NW Spain). The chosen method was applied in the determination of the Cd content in 38 representative Galician samples. The cadmium concentrations ranged

  6. Direct determination of cadmium in Orujo spirit samples by electrothermal atomic absorption spectrometry: Comparative study of different chemical modifiers

    International Nuclear Information System (INIS)

    Vilar Farinas, M.; Barciela Garcia, J.; Garcia Martin, S.; Pena Crecente, R.; Herrero Latorre, C.

    2007-01-01

    In this work, several analytical methods are proposed for cadmium determination in Orujo spirit samples using electrothermal atomic absorption spectrometry (ETAAS). Permanent chemical modifiers thermally coated on the platforms inserted in pyrolytic graphite tubes (such as W, Ir, Ru, W-Ir and W-Ru) were comparatively studied in relation to common chemical modifier mixtures [Pd-Mg(NO 3 ) 2 and (NH 4 )H 2 PO 4 -Mg(NO 3 ) 2 ] for cadmium stabilization. Different ETAAS Cd determination methods based on the indicated modifiers have been developed. In each case, pyrolysis and atomization temperatures, atomization shapes, characteristic masses and detection limits as well as other analytical characteristics have been determined. All the assayed modifiers (permanent and conventional) were capable of achieving the appropriate stabilization of the analyte, with the exception of Ru and W-Ru. Moreover, for all developed methods, recoveries (99-102%) and precision (R.S.D. lower than 10%) were acceptable. Taking into account the analytical performance (best detection limit LOD = 0.01 μg L -1 ), the ETAAS method based on the use of W as a permanent modifier was selected for further direct Cd determinations in Orujo samples from Galicia (NW Spain). The chosen method was applied in the determination of the Cd content in 38 representative Galician samples. The cadmium concentrations ranged -1

  7. Iodine and Selenium Biofortification with Additional Application of Salicylic Acid Affects Yield, Selected Molecular Parameters and Chemical Composition of Lettuce Plants (Lactuca sativa L. var. capitata)

    Science.gov (United States)

    Smoleń, Sylwester; Kowalska, Iwona; Czernicka, Małgorzata; Halka, Mariya; Kęska, Kinga; Sady, Włodzimierz

    2016-01-01

    Iodine (I) and selenium (Se) are included in the group of beneficial elements. They both play important roles in humans and other animals, particularly in the regulation of thyroid functioning. A substantial percentage of people around the world suffer from health disorders related to the deficiency of these elements in the diet. Salicylic acid (SA) is a compound similar to phytohormones and is known to improve the efficiency of I biofortification of plants. The influence of SA on Se enrichment of plants has not, however, been recognized together with its effect on simultaneous application of I and Se to plants. Two-year studies (2014–2015) were conducted in a greenhouse with hydroponic cultivation of lettuce in an NFT (nutrient film technique) system. They included the application of I (as KIO3), Se (as Na2SeO3) and SA into the nutrient solution. KIO3 was used at a dose of 5 mg I⋅dm-3 (i.e., 39.4 μM I), while Na2SeO3 was 0.5 mg Se⋅dm-3 (i.e., 6.3 μM Se). SA was introduced at three doses: 0.1, 1.0, and 10.0 mg⋅dm-3 nutrient solutions, equivalent to 0.724, 7.24, and 72.4 μM SA, respectively. The tested combinations were as follows: (1) control, (2) I + Se, (3) I + Se + 0.1 mg SA⋅dm-3, (4) I + Se + 1.0 mg SA⋅dm-3 and (5) I + Se + 10.0 mg SA⋅dm-3. The applied treatments had no significant impact on lettuce biomass (leaves and roots). Depending on the dose, a diverse influence of SA was noted with respect to the efficiency of I and Se biofortification; chemical composition of leaves; and mineral nutrition of lettuce plants, including the content of macro- and microelements and selenocysteine methyltransferase (SMT) gene expression. SA application at all tested doses comparably increased the level of selenomethionine (SeMet) and decreased the content of SA in leaves. PMID:27803709

  8. Pea weevil damage and chemical characteristics of pea cultivars determining their resistance to Bruchus pisorum L.

    Science.gov (United States)

    Nikolova, I

    2016-04-01

    Bruchus pisorum (L.) is one of the most intractable pest problems of cultivated pea in Europe. Development of resistant cultivars is very important to environmental protection and would solve this problem to a great extent. Therefore, the resistance of five spring pea cultivars was studied to B. pisorum: Glyans, Modus; Kamerton and Svit and Pleven 4 based on the weevil damage and chemical composition of seeds. The seeds were classified as three types: healthy seeds (type one), damaged seeds with parasitoid emergence holes (type two) and damaged seeds with bruchid emergence holes (type three). From visibly damaged pea seeds by pea weevil B. pisorum was isolated the parasitoid Triaspis thoracica Curtis (Hymenoptera, Braconidae). Modus, followed by Glyans was outlined as resistant cultivars against the pea weevil. They had the lowest total damaged seed degree, loss in weight of damaged seeds (type two and type three) and values of susceptibility coefficients. A strong negative relationship (r = -0.838) between the weight of type one seeds and the proportion of type three seeds was found. Cultivars with lower protein and phosphorus (P) content had a lower level of damage. The crude protein, crude fiber and P content in damaged seeds significantly or no significantly were increased as compared with the healthy seeds due to weevil damage. The P content had the highest significant influence on pea weevil infestation. Use of chemical markers for resistance to the creation of new pea cultivars can be effective method for defense and control against B. pisorum.

  9. Chemical composition determination of Bohunice 1 and 2 RPVs and hardness measurements of RPVs material

    International Nuclear Information System (INIS)

    Kupca, L.; Brezina, M.; Beno, P.; Kniz, I.

    1994-01-01

    The base informations of all activities concerning the material properties recovery performed before and after annealing procedure on the first two units V-230 type in NPP V-1, are the topic of this paper. The samples of weld and base metal from both RPVs NPP V-1 were prepared by special apparatus in the very narrow gap between the outside surface of the RPV and the reactor thermal shielding in the reactor cavity, from the critical circumferential weld joint no.4. The chemical composition of the samples was analyzed in Nuclear Power Plants Research Institute (VUJE) laboratories. Except these results achieved from the analysis of the irradiated samples are presented the evaluation results of the chemical composition influence on the RPVs materials brittle fracture temperatures. All these results which served as input data for the irradiation embrittlement recovery evaluation of the both RPV NPP V-1 in Jaslovske Bohunice, are presented in the form of the trend curves for both RPVs. (author). 10 refs, 7 figs, 1 tab

  10. Atributos químicos do solo, crescimento radicular e produtividade do arroz de acordo com a aplicação de escórias Soil chemical attributes, root growth and rice yield according to slag application

    Directory of Open Access Journals (Sweden)

    Juliana Garcia Carvalho-Pupatto

    2004-12-01

    Full Text Available Resíduos industriais são fontes alternativas de nutrientes para as plantas e sua utilização decorre da necessidade de diminuir o acúmulo dos resíduos nos centros de produção. O objetivo deste trabalho foi avaliar o efeito de escórias de siderurgia nos atributos químicos do solo, no desenvolvimento e na produtividade de grãos do arroz de terras altas irrigado por aspersão. O delineamento experimental foi em blocos casualizados, com três tratamentos constituídos de duas escórias, alto-forno (196 g kg-1 de Si e aciaria (56 g kg-1 de Si, e a testemunha sem aplicação, com oito repetições. As escórias podem ser usadas como corretivo de acidez do solo e como fonte de silício. As alterações nos atributos químicos do solo estão relacionadas com a composição química das escórias. A escória de alto-forno proporcionou maior crescimento radicular em profundidade e melhor distribuição no perfil do solo e, conseqüentemente, maior produção de massa de matéria seca da parte aérea e produtividade de grãos de arroz.Use of industrial residues as alternative sources of nutrients to the plants is due to the necessity of reducing their accumulation in the production sites. The objective of this work was to evaluate the effect of metallurgy slag in soil chemical attributes, in development and in grain yield of upland rice sprinkler irrigated. The experiment was carried out in a randomized block design, with three treatments constituted by two scums, blast furnace (196 g kg-1 of Si and steel slag (56 g kg-1 of Si, and a control without application, with eight replications. The scums can be used as corrective of soil acidity and silicon source. Alterations in the soil chemical attributes are related to the chemical composition of the scums. Blast furnace slag resulted in higher root growth in depth and better distribution in the profile soil provides higher shoot dry matter yield and grain yield.

  11. Determination of complex reaction mechanisms: analysis of chemical, biological, and genetic networks

    National Research Council Canada - National Science Library

    Ross, John; Schreiber, Igor; Vlad, Marcel O

    2006-01-01

    ... Systems, 40 5 Response of Systems to Pulse Perturbations, 46 5.1 5.2 Theory, 46 An Example: The Glycolytic Pathway, 53 6 Experimental Test of the Pulse Perturbation Method for Determining Causa...

  12. Determination of beryllium in water using silica gel chemically modified with aminophosphonic acid

    International Nuclear Information System (INIS)

    Zajtseva, G.N.; Strelko, V.V.

    2001-01-01

    Considered are methods of Be determination based on Be isolation from the solutions using aminophosphonic acid covalently bound on silica gel surface (APA-SiO 2 ) and subsequent photometric or atomic-absorption determination of Be in eluate ( the limit of Be determination is 0.00005 mg/l or 0.00008 mg/l, respectively). APA-SiO 2 high efficiency and a possibility of beryllium ions extraction from diluted solutions by means of sorbent small weighed portions is shown. High efficiency of the sorbent both for concentration and waters purification from beryllium is shown. Methods are tested in analysis of waste water. To assess the accuracy of the proposed methods, parallel determination of beryllium in tests by means of the additions method was carried out. The given data testify to a sufficient accuracy and reproducibility of the proposed methods [ru

  13. Determination of chemical elements in africanized Apis mellifera (Hymenoptera: Apidae honey samples from the State of Piauí, Brazil

    Directory of Open Access Journals (Sweden)

    Geni da Silva Sodré

    2007-08-01

    Full Text Available Honey is a food used since the most remote times, appreciated for its characteristic flavor, considerable nutritional value and medicinal properties; however, little information exists about the presence of chemical elements in it. The objectives of this work were to determine the chemical elements present in 38 honey samples, collected directly from beekeepers from the State of Piauí, Brazil and to verify whether they presented any contamination. The chemical elements were determined by means of Total Reflection X-ray Fluorescence. The means of three replicates were: K (109.671 ± 17.487, Ca (14.471 ± 3.8797, Ti (0.112 ± 0.07, Cr (0.196 ± 0.11, Mn (0.493 ± 0.103, Fe (1.722 ± 0.446, Co (0.038, Ni (0.728 ± 0.706, Cu (0.179 ± 0.0471, Zn (0.967 ± 0.653, Se (not detected, Br (not detected, Rb (0.371 ± 0.097, Sr (0.145 ± 0.45, Ba (11.681, Hg (not detected, and Pb (0.863 µg g-1.

  14. Simultaneous determination of some ultraviolet-absorbing chemicals in sunscreen cosmetics using a high-performance liquid chromatography method.

    Science.gov (United States)

    Liu, T; Wu, D

    2011-10-01

    A method of gradient elution high-performance liquid chromatography (HPLC) for simultaneous determination of 11 different ultraviolet-absorbing chemicals of phenylbenzlmldazole sulphonic acid, 4-aminobenzoic acid, benzophenone-4, benzophenone-3, isoamyl p-methoxycinnamate, 4-methylbenzylidene camphor, octocrylene, ethylhexyl methoxycinnamate, homosalate, ethylhexyl salicylate, methylene bis-benzotriazolyl tetramethylbutyl phenol was developed for the application to sunscreen cosmetic products. In this study, an Agilent SB-C18 analytical column (250 × 4.6 mm, 5 μm) was utilized and methanol, tetrahydrofuran and perchloric acid aqueous solution (0.2 mL HClO(4) + 300 mL H(2)O) were used for gradient elution at a total flow rate of 1.0 mL min(-1). The optimum conditions for 11 different ultraviolet-absorbing chemicals analyses were investigated. All calibration curves showed good linear regression with UV detection (311 nm) within test ranges. The correlation coefficients were better than 0.999 in all cases. The assay was simple, selective, convenient and reproducible and is suitable for the determination of ultraviolet-absorbing chemicals in commercial sunscreen cosmetic products. The use frequency of 11 different ultraviolet absorbents in 100 sunscreen cosmetics was investigated and statistically analysed. The ultraviolet absorbent of maximum use frequency was ethylhexyl methoxycinnamate. © 2011 The Authors. ICS © 2011 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

  15. Use of the fluorescence quantum yield for the determination of the number-average molecular weight of polymers of epicatechin with 4β→8 interflavin bonds

    Science.gov (United States)

    D. Cho; W.L. Mattice; L.J. Porter; Richard W. Hemingway

    1989-01-01

    Excitation at 280 nm produces a structureless emission band with a maximum at 321-324 nm for dilute solutions of catechin, epicatechin, and their oligomers in l,4-dioxane or water. The fluorescence quantum yield, Q, has been measured in these two solvents for five dimers, a trimer, a tetramer, a pentamer, a hexamer, and a polymer in which the monomer...

  16. Determination of clebopride in plasma by capillary gas chromatography-negative-ion chemical ionization mass spectrometry.

    Science.gov (United States)

    Robinson, P R; Jones, M D; Maddock, J

    1988-11-18

    A procedure for the analysis of clebopride in plasma using capillary gas chromatography-negative-ion chemical ionization mass spectrometry has been developed. Employing an ethoxy analogue as internal standard, the two compounds were extracted from basified plasma using dichloromethane. Subsequent reaction with heptafluorobutyryl imidazole produced volatile monoheptafluorobutyryl derivatives whose ammonia negative-ion mass spectra proved ideal for selected-ion monitoring. The recovery of clebopride from plasma at 0.536 nmol/l was found to be 85.5 +/- 0.9% (n = 3) whilst measurement down to 0.268 nmol/l was possible with a coefficient of variation of 7.9%. Plasma levels of the compound are reported in two volunteers following ingestion of 1 mg of clebopride as the malate salt.

  17. Extraction tools for identification of chemical contaminants in estuarine and coastal waters to determine toxic pressure on primary producers.

    Science.gov (United States)

    Booij, Petra; Sjollema, Sascha B; Leonards, Pim E G; de Voogt, Pim; Stroomberg, Gerard J; Vethaak, A Dick; Lamoree, Marja H

    2013-09-01

    The extent to which chemical stressors affect primary producers in estuarine and coastal waters is largely unknown. However, given the large number of legacy pollutants and chemicals of emerging concern present in the environment, this is an important and relevant issue that requires further study. The purpose of our study was to extract and identify compounds which are inhibitors of photosystem II activity in microalgae from estuarine and coastal waters. Field sampling was conducted in the Western Scheldt estuary (Hansweert, The Netherlands). We compared four different commonly used extraction methods: passive sampling with silicone rubber sheets, polar organic integrative samplers (POCIS) and spot water sampling using two different solid phase extraction (SPE) cartridges. Toxic effects of extracts prepared from spot water samples and passive samplers were determined in the Pulse Amplitude Modulation (PAM) fluorometry bioassay. With target chemical analysis using LC-MS and GC-MS, a set of PAHs, PCBs and pesticides was determined in field samples. These compound classes are listed as priority substances for the marine environment by the OSPAR convention. In addition, recovery experiments with both SPE cartridges were performed to evaluate the extraction suitability of these methods. Passive sampling using silicone rubber sheets and POCIS can be applied to determine compounds with different structures and polarities for further identification and determination of toxic pressure on primary producers. The added value of SPE lies in its suitability for quantitative analysis; calibration of passive samplers still needs further investigation for quantification of field concentrations of contaminants. Copyright © 2013 Elsevier Ltd. All rights reserved.

  18. Determination of organic products resulting of chemical and radiochemical decompositions of bitumen. Applications to embedded bitumens

    International Nuclear Information System (INIS)

    Walczak, I.

    2000-01-01

    Bitumen can be used for embedding most of wastes because of its high impermeability and its relatively low reactivity with of chemicals. Bituminization is one of selected solutions in agreement with nuclear safety, waste compatibility and economic criteria. Bitumen, during storage, undergoes an auto-irradiation due to embedded radio-elements. During this stage,drums are not airtight then oxygen is present. In disposal configuration, water, which is a potential vector of radioactivity and organic matter, is an other hazard factor liable to deteriorate the containment characteristics of bitumen wastes. The generation of water-soluble organic complexing agents can affect the integrity of the wasteform due to an increase of the radionuclides solubility. The first aim of this work is the quantitative and qualitative characterisation of soluble organic matter in bitumen leachates. Different leaching solutions were tested (various pH, ionic strength, ratio S/V). When the pH of the leaching solutions increases, the total organic carbon released increases as well. Identified molecules are aromatics like naphthalene, oxidised compounds like alcohols, linear carbonyls, aromatics, glycols and nitrogen compounds. For the cement equilibrated solution (pH 13.5), the effect of ionic strength becomes significative and influences the release of soluble organic matter. This soluble organic matter can be bio-degraded if microorganisms can growth. The second aim of this work is to study the effect of radio-oxidative ageing on the bitumen confinement properties. During radio-oxidation, the chemical properties of bitumen are modified. The μ-IRTF analysis shows the formation of hydroxyl compounds and aromatic acids. The formation of these polar groups does not influence in our study the water uptake. However the organic matter release increases significantly with the irradiation dose. (author)

  19. Chemical and biological tracers to determine groundwater flow in karstic aquifer, Yucatan Peninsula

    Science.gov (United States)

    Lenczewski, M.; Leal-Bautista, R. M.; McLain, J. E.

    2013-05-01

    Little is known about the extent of pollution in groundwater in the Yucatan Peninsula; however current population growth, both from international tourism and Mexican nationals increases the potential for wastewater release of a vast array of contaminants including personal care products, pharmaceuticals (Rx), and pathogenic microorganisms. Pathogens and Rx in groundwater can persist and can be particularly acute in this region where high permeability of the karst bedrock and the lack of top soil permit the rapid transport of contaminants into groundwater aquifers. The objective of this research is to develop and utilize novel biological and chemical source tracking methods to distinguish between different sources of anthropogenic pollution in degraded groundwater. Although several methods have been used successfully to track fecal contamination sources in small scale studies, little is known about their spatial limitations, as source tracking studies rarely include sample collection over a wide geographical area and with different sources of water. In addition, although source tracking methods to distinguish human from animal fecal contamination are widely available, this work has developed source tracking distinguish between separate human populations is highly unique. To achieve this objective, we collected water samples from a series of drinking wells, cenotes (sinkholes), wastewater treatment plants, and injection wells across the Yucatan Peninsula and examine potential source tracers within the collected water samples. The result suggests that groundwater sources impacted by tourist vs. local populations contain different chemical stressors. This work has developed a more detailed understanding of the presence and persistence of personal care products, pharmaceuticals, and fecal indicators in a karstic system; such understanding will be a vital component for the protection Mexican groundwater and human health. Quantification of different pollution sources

  20. Determining the most important physiological and agronomic traits contributing to maize grain yield through machine learning algorithms: a new avenue in intelligent agriculture.

    Directory of Open Access Journals (Sweden)

    Avat Shekoofa

    Full Text Available Prediction is an attempt to accurately forecast the outcome of a specific situation while using input information obtained from a set of variables that potentially describe the situation. They can be used to project physiological and agronomic processes; regarding this fact, agronomic traits such as yield can be affected by a large number of variables. In this study, we analyzed a large number of physiological and agronomic traits by screening, clustering, and decision tree models to select the most relevant factors for the prospect of accurately increasing maize grain yield. Decision tree models (with nearly the same performance evaluation were the most useful tools in understanding the underlying relationships in physiological and agronomic features for selecting the most important and relevant traits (sowing date-location, kernel number per ear, maximum water content, kernel weight, and season duration corresponding to the maize grain yield. In particular, decision tree generated by C&RT algorithm was the best model for yield prediction based on physiological and agronomical traits which can be extensively employed in future breeding programs. No significant differences in the decision tree models were found when feature selection filtering on data were used, but positive feature selection effect observed in clustering models. Finally, the results showed that the proposed model techniques are useful tools for crop physiologists to search through large datasets seeking patterns for the physiological and agronomic factors, and may assist the selection of the most important traits for the individual site and field. In particular, decision tree models are method of choice with the capability of illustrating different pathways of yield increase in breeding programs, governed by their hierarchy structure of feature ranking as well as pattern discovery via various combinations of features.

  1. Production of granular activated carbon from agricultural wastes and determination of their physical, chemical and adsorption properties

    Energy Technology Data Exchange (ETDEWEB)

    Ayguen, A.; Duman, I. [Istanbul Technical Univ., Inst. of Science and Technology, Dept. of Metallurgical Engineering, Istanbul (Turkey); Yenisoy-Karakas, S. [TUeBITAK Marmara Research Center (MRC), Materials and Chemical Technologies Research Inst., Gebze Kocaeli (Turkey)

    2004-07-01

    The aim of this study is to produce activated carbons with good mechanical strength and high adsorption capacities toward various organics from food wastes such as walnut, almond, hazelnut shells and apricot stones. Turkey has huge amounts of these wastes in canning industry. The chemical activation with ZnCl{sub 2} was preferred to manufacture activated carbons. The best activation temperature and time were determined. Granular activated carbons were discussed with respect to their physical, chemical, surface area and adsorption properties. For all raw materials, the specific surface areas of greater than 730 m{sup 2} g{sup -1} were reached. As a result of the adsorption studies, adsorption capacities were in order of hazelnut> apricot stones> walnut> almond. The correlation coefficients obtained from Langmuir and Freundlich isotherms are in good agreement with the experimental results. (orig.)

  2. Determination of antioxidant activity in herbal ingredients for foods using new methods of chemical analysis

    Directory of Open Access Journals (Sweden)

    Katalina Muñoz

    2012-06-01

    Full Text Available A new procedure has been used to separate and quantify the free radical-scavenging activity of individual compounds 18 samples of Thymus vulgaris and 12 samples of Rosmarinus officinalis (both used as natural food preservatives, based on the combination of HPTLC (High Performance Thin Layer Chromatography and postchromatographic DPPH● radical derivatization. The compounds thymol and rosmarinic acid in T. vulgaris and R. officinalis, respectively, were identified by comparisons of their Rf values and UV spectra to standards analyzed under identical analytical conditions, while the quantitative data were calculated from their calibration curves. We found that not only that the biomass yield but also the metabolite content in herbs, depend on the ecotype (genetics and on the agro ecological conditions. The effect of the ambient on the metabolite content is extremely significant and also on their antioxidant activity (One-way ANOVA with Newman-Keuls Multiple Comparison post test was performed using GraphPad Prism version 4.00 for Windows, GraphPad Software. This work pretends to demonstrate the great importance of using new technologies for the selection of the best materials used as natural food preservatives.

  3. Chemical analytical considerations on the determination of burnup in irradiated nuclear fuels

    International Nuclear Information System (INIS)

    Cretella, R.F.; Servant, R.E.

    1989-01-01

    Burnup in an irradiated nuclear fuel may be defined as the energy produced per mass unit, from the time the fuel is introduced into the reactor and until a given moment. It is usually shown in megawatt/day or megawatt/hour generated per ton or kilo of fuel. It is also indicated as the number of fission produced per volume unit (cm 3 ) or per every 100 initial fissionable atoms. The yield of a power plant is directly related to the burnup of its fuel load and knowing the latter contributes to optimizing the economy in reactor operation and the related technologies. The development of nuclear fuels and the operation of reactors require doing with exact and accurate methods allowing to know the burnup. Errors in this measurement have an incidence upon the fuel design, the physical and nuclear calculations, the shielding requirements, the design of vehicles for the transportation of irradiated fuels, the engineering of processing plants, etc. All these factors, in turn, have an incidence upon the cost of nuclear power generation. (Author) [es

  4. Assessment of CREAMS [Chemicals, Runoff, and Erosion from Agricultural Management Systems] and ERHYM-II [Ekalaka Rangeland Hydrology and Yield Model] computer models for simulating soil water movement on the Idaho National Engineering Laboratory

    International Nuclear Information System (INIS)

    Laundre, J.W.

    1990-05-01

    The major goal of radioactive waste management is long-term containment of radioactive waste. Long-term containment is dependent on understanding water movement on, into, and through trench caps. Several computer simulation models are available for predicting water movement. Of the several computer models available, CREAMS (Chemicals, Runoff, and Erosion from Agricultural Management Systems) and ERHYM-II (Ekalaka Rangeland Hydrology and Yield Model) were tested for use on the Idaho National Engineering Laboratory (INEL). The models were calibrated, tested for sensitivity, and used to evaluate some basic trench cap designs. Each model was used to postdict soil moisture, evapotranspiration, and runoff of two watersheds for which such data were already available. Sensitivity of the models was tested by adjusting various input parameters from high to low values and then comparing model outputs to those generated from average values. Ten input parameters of the CREAMS model were tested for sensitivity. 17 refs., 23 figs., 20 tabs

  5. The Determination of Uranium and Trace Metal Impurities in Yellow Cake Sample by Chemical Method

    International Nuclear Information System (INIS)

    Busamongkol, Arporn; Rodthongkom, Chouvana

    1999-01-01

    The purity of uranium cake is very critical in nuclear-grade uranium (UO 2 ) and uranium hexafluoride (UF 6 ) production. The major element in yellow cake is uranium and trace metal impurities. The objective of this study is to determine uranium and 25 trace metal impurities; Aluminum, Barium, Bismuth, Calcium, Cadmium, Cobalt, Chromium, Copper, Iron, Potassium, Iithium, Magnesium, Manganese, Molybdenum, Sodium, Niobium, Nickel, Lead, Antimony, Tin, Strontium, Titanium, Vanadium, Zinc and Zirconium, Uranium is determined by Potassium dichromate titration, after solvent extraction with Cupferon in Chloroform, Trace metal impurities are determined by solvent extraction with Tributyl Phosphate in Carbon-tetrachloride ( for first 23 elements) and N-Benzoyl-N-Phenylhydroxylamine in Chloroform ( for last 2 elements), then analyzed by Atomic Absorption Spectrophotometer (AAS) compared with Inductively Couple Plasma Spectrophotometers (ICP). The accuracy and precision are studied with standard uranium octaoxide

  6. PHYSICO-CHEMICAL DETERMINATION OF CARBOHYDRATES IN THE FOODS AND BEVERAGES

    Directory of Open Access Journals (Sweden)

    I. I. Korenman

    2014-01-01

    Full Text Available Summary. The extraction of fructose, glucose, galactose, sucrose and lactose from aqueous salt solutions, hydrophilic solvents (aliphatic alcohols, alkyl acetates, ketones of double and triple mixtures has been studied. Under identical conditions set quantitative characteristics extraction has been established. It was found that from the all studied carbohydrateы most fully extracted disaccharides lactose and sucrose. The conditions of concentration and almost complete recovery of carbohydrates from aqueous salt solutions has beenoptimized. The technique of extraction-potentiometric selective determination of carbohydrates in foods and beverages has been developed. As a titrant was used isopropanol solution of boric acid. The developed method allows to determine separately the mono- or disaccharides in milk, which include those contained 5 or less carbohydrates. The complex of photocolorimetric, polarimetric, potentiometric and chromatographic methods for determining carbohydrates in aqueous media and food (diabetic confectionery, juices, dairy products, honey wasproposed. To determine the fructose, glucose and sucrose in natural juices us used optical methods (photoelectrocolorimeters, polarimetry. Method is express, does not require expensive equipment and reagents. Fructose and sucrose in diabetic confectionery was determined by ascending thin layer chromatography. Some diabetic products based on fructose, produced by Russian confectionery factorieshas beenanalyzed. Duration analysis, 50-60 minutes, selective determination of error within 5-7%. Extracts from honey and milk were analyzed potentiometrically. We have developed a technique characterized by the following advantages compared with state standards: rapidity (analysis time 30-35 min, accuracy (relative error within 5 %, does not require expensive equipment and reagents, as well as dilution and filtration of milk stage sampling.

  7. Passive Dosing to Determine the Speciation of Hydrophobic Organic Chemicals in Aqueous Samples

    DEFF Research Database (Denmark)

    Birch, Heidi; Gouliarmou, V.; Lützhøft, Hans-Christian Holten

    2010-01-01

    A new analytical approach to determine the speciation of hydrophobic organic analytes is presented. The freely dissolved concentration in a sample is controlled by passive dosing from silicone (poly(dimethylsiloxane)), and the total sample concentration at equilibrium is measured. The free fraction...... is determined as the ratio between measured concentrations in pure water and sample. C-14-labeled fluoranthene served as model analyte, and total sample concentrations were easily measured by liquid scintillation counting. The method was applied to surface water, stormwater runoff, and wastewater...... (SPME). This analytical approach combines simplicity with high precision, and it does not require any phase separation steps....

  8. Uncertainties combined in algae and water in chemical analysis in determinations with ICP-OES

    International Nuclear Information System (INIS)

    Souza, Poliana Santos de

    2014-01-01

    One way to determine if some trace elements in algae and water is through uncertainty calculations. Spectrometry and inductively coupled plasma optical emission (ICP-OES) is widely used in this procedure, because it allows the analysis in waters and areas of solid samples. Thus, some elements (Fe, Ca and Mg) were used to calculate the uncertainty. (author)

  9. Determination of microbiological and chemical properties of probiotic boza and its consumer acceptability.

    Science.gov (United States)

    Arslan, Sultan; Durak, Atike N; Erbas, Mustafa; Tanriverdi, Emel; Gulcan, Ummugulsum

    2015-01-01

    The aim of research was producing boza as a probiotic product with certificated probiotic starter cultures (Lactobacillus acidophilus LA-5 and Bifidobacterium bifidum BB-12 and Saccharomyces boulardii). Analysis were done in boza samples taken in fermentation and storage. Probiotic and non-probiotic bacteria were enumerated with pour plate technique and yeast enumerated spread plate technique. Sugar, organic acid and Water soluble vitamin content were determined by using of HPLC. Sensory analyses were done by two different types of panels, once comprised of trained panelists and the other of consumers. Shelf life was determined according the results of sensory analysis. It was determinated that S. boulardii and L acidophilius counts increased nearly 0.5 log unit during of boza fermentation. Lactic, acetic, citric, butyric and succinic acid as organic acids and thiamin, niacin, B6 and pantothenic acid as water soluble vitamin evaluated in boza samples. Shelf life of the probiotic boza determined as 12 days at +4°C fridge storage temperature. The boza samples had a probiotic effect because it had viable microorganisms more than 10(6) cfu/ml which was defined enough for functional foods. All boza samples had lower pH value than 4.5, so it is evaluated that boza is a safety food as its low pH preventing pathogen growth.

  10. Determination of rhenium in molybdenite by X-ray fluorescence: A combined chemical-spectrometric technique.

    Science.gov (United States)

    Solt, M W; Wahlberg, J S; Myers, A T

    1969-01-01

    Rhenium in molybdenite is separated from molybdenum by distillation of rhenium heptoxide from a perchloric-sulphuric acid mixture. It is concentrated by precipitation of the sulphide and then determined by X-ray fluorescence. From 3 to 1000 microg of rhenium can be measured with a precision generally within 2%. The procedure tolerates larger amounts of molybdenum than the usual colorimetric methods.

  11. Determination of rhenium in molybdenite by X-ray fluorescence. A combined chemical-spectrometric technique

    Science.gov (United States)

    Solt, M.W.; Wahlberg, J.S.; Myers, A.T.

    1969-01-01

    Rhenium in molybdenite is separated from molybdenum by distillation of rhenium heptoxide from a perchloric-sulphuric acid mixture. It is concentrated by precipitation of the sulphide and then determined by X-ray fluorescence. From 3 to 1000 ??g of rhenium can be measured with a precision generally within 2%. The procedure tolerates larger amounts of molybdenum than the usual colorimetric methods. ?? 1969.

  12. Determining the Chemical and Biological Availability of Zinc in Urban Stormwater Retention Ponds

    Science.gov (United States)

    Camponelli, K.; Casey, R.; Lev, S. M.; Landa, E. R.; Snodgrass, J.

    2005-12-01

    Highway runoff has the potential to negatively impact receiving systems due to transport of contaminants that accumulate on road surfaces. Metals such as copper and zinc are major components of automobile brake pads and tires, respectively. As these automobile parts are degraded, these metal containing particulates are deposited on the roadway and are washed into storm water retention ponds and surface water bodies during precipitation events. It has been estimated that 15 to 60% of the Zn in urban stormwater runoff comes from tire wear and that tire wear is a significant source of Zn to the environment with release inventories comparable to waste incineration sources. In urban and sub-urban systems, this large source of Zn can accumulate in stormwater retention ponds which serve as habitat for a variety of species. Understanding the chemical and biological availability of Zn to biota is integral to assessing the habitat quality of retention ponds. This study is a first effort to relate the amount and speciation of Zn in a retention pond to Zn inputs through highway-derived runoff events. In addition, results suggest that the chemical speciation and availability of particulate Zn can be related to the bioavailability and toxicity of Zn to pond organisms (i.e. larval amphibians). The study site in Owings Mills, MD is located next to a four-lane highway from which it receives runoff through a single culvert. Five species of anurans are known to utilize the pond as a breeding site and Zn in amphibian tissues and retention pond sediments were highly elevated at this site in 2001 and 2002. A recent analysis of pond sediments, soils, roadway dust and storm water collected at this site suggests that roadway particulate matter transported during runoff events is the dominant source of Zn in this system. Overall, Zn and other trace metals were found to be most abundant in the clay sized faction of pond sediments and soils. The pond cores were found to have higher Zn and Cu

  13. Radioisotopic methods - determination of action of toxic chemicals to food - digestion organs

    International Nuclear Information System (INIS)

    Saitmuratova, O.H.; Tursunov, E.A.

    2004-01-01

    Full text: It is known that poison chemicals used for agriculture enter in an organism of human and animal by various ways and affect key processes in cells and tissues. These processes are investigated insufficiently, nevertheless, investigating actions of chemicals on bodies and tissues it, is possible to define a degree of its toxicity. In the present work influence of defoliant drop and insecticide buldok on protein synthetic ability (PSA) of cells of digestive bodies (a liver, a stomach and duodenal gut) is investigated. Experiments carried out on white not purebred rats - males in weight 160-180 g, which entered drop in doze of 1/5 IC 50 5350 mg/kg, buldok 1/5 IC 50 400 mg/kg and 14 C-glutamine acid with the general activity 1 mk Curie (2.2*106 imp/min) in one hour up to slaughter. A control animal in parallel entered a physiological solution. In animals hammered in one hour and investigated inclusion 14 C- glutamine acids in structure of synthesized proteins of a liver, a stomach and duodenal gut. Action of preparations checked in 1, 24 and 72 hours after introduction. As have shown the received data drop suppresses PSA in cells of a liver on 14 % and 45 % in 24 and 72 hours accordingly; in a stomach - on 32 % and 34 %; in duodenal gut - on 39 % and 48 %. PSA it is more suppressed in a stomach. Further process is gradually restored in all bodies. Buldok in the same terms suppresses PSA in a liver on 4 % and 25 %; in a stomach of 4 % and 16 % and in duodenal gut on the contrary are raised with formation of protein on 27 %. The next day there is restoration PSA in all investigated bodies. From the received data it is visible, that defoliant drop as well as insecticide buldok influence on PSA cells, but action of drop is stronger, than buldok. It will be coordinated to earlier received data on change of morphological structures under influence of these pesticides. Though drop and buldok differ on dynamics of action on PSA digestive bodies, they are not strongly

  14. Determining octanol-water partition coefficients for extremely hydrophobic chemicals by combining "slow stirring" and solid-phase microextraction.

    Science.gov (United States)

    Jonker, Michiel T O

    2016-06-01

    Octanol-water partition coefficients (KOW ) are widely used in fate and effects modeling of chemicals. Still, high-quality experimental KOW data are scarce, in particular for very hydrophobic chemicals. This hampers reliable assessments of several fate and effect parameters and the development and validation of new models. One reason for the limited availability of experimental values may relate to the challenging nature of KOW measurements. In the present study, KOW values for 13 polycyclic aromatic hydrocarbons were determined with the gold standard "slow-stirring" method (log KOW 4.6-7.2). These values were then used as reference data for the development of an alternative method for measuring KOW . This approach combined slow stirring and equilibrium sampling of the extremely low aqueous concentrations with polydimethylsiloxane-coated solid-phase microextraction fibers, applying experimentally determined fiber-water partition coefficients. It resulted in KOW values matching the slow-stirring data very well. Therefore, the method was subsequently applied to a series of 17 moderately to extremely hydrophobic petrochemical compounds. The obtained KOW values spanned almost 6 orders of magnitude, with the highest value measuring 10(10.6) . The present study demonstrates that the hydrophobicity domain within which experimental KOW measurements are possible can be extended with the help of solid-phase microextraction and that experimentally determined KOW values can exceed the proposed upper limit of 10(9) . Environ Toxicol Chem 2016;35:1371-1377. © 2015 SETAC. © 2015 SETAC.

  15. Determination and analysis of the physical chemical characteristics of witness coupons of boral for the CNLV

    International Nuclear Information System (INIS)

    Gonzalez M, J.L.; Aguilar H, F.; Rivero G, T.; Carrillo M, R.

    2004-01-01

    The burnt fuel elements that are extracted in each charging of the Units 1 and 2 of the Nuclear Power Plant of Laguna Verde, are deposited in shelves placed in the storage reservoir designed for this end. Each cell or storage shelf has a structure type cage. Among the cells neutron absorber material is placed, (Boral), what allows to avoid the possible criticality that could settle down when accumulating in the storage the irradiated fuel elements. This boral has been designed to maintain its characteristics of thermal neutron absorber during a lifetime of the plant. To check that the wings and the Boral have not suffered some degradation or some change due to the environmental conditions in the warehouse, it is necessary to watch over their physical and chemical characteristics periodically, what is carried out by a surveillance program based on Badges or manufactured witness coupons of the same material that the wings. The badges witness are embedded in a special wing, which is placed in the place with more radiation in the pool. In this work the laboratory tests carried out in the ININ to the coupon witness 03 of the Unit 2, (II-03) are described, being presented the results and obtained conclusions. (Author)

  16. A physico-chemical characterisation technique for determining the pore-water chemistry in argillaceous rocks

    International Nuclear Information System (INIS)

    Baeyens, B.; Bradbury, M.H.

    1991-09-01

    A prerequisite for carrying out credible sorption studies is the definition of an aqueous phase composition which is in equilibrium with the solid phase. Experimental methods and data analysis procedures are described which enable an equilibrium water composition to be produced for argillaceous rocks which is not dependent on liquid to solid (L:S) ratios. Since a Valanginian marl formation is under consideration by Nagra as a potential rock for the disposal of low and short-lived medium level radioactive waste in Switzerland, samples of this material were chosen for this investigation. Aqueous phase and nickel ethylenediamine extraction experiments were carried out at different L:S ratios under controlled atmosphere conditions (P CO 2 =10 -2 bar, O 2 ≤ 5 ppm ). The results from these tests and petrographical examinations were combined to define the system in terms of the physico-chemical characteristics of the clay mineral component (CEC and cation occupancies) and the identities of highly soluble and solubility limited phases in the marl. The geochemical code PHREEQE was used in conjunction with the Gapon equations to calculate the pore water composition. This work clearly showed that pore water chemistries obtained from aqueous extracts alone may lead to an arbitrary water chemistry in argillaceous rock systems, particularly with respect to ionic composition and ionic strength, which may have important consequences for radionuclide speciation and sorption studies. (author) 11 figs., 12 tabs., 25 refs

  17. Determination of chemical availability of cadmium and zinc in soils using inert soil moisture samplers.

    Science.gov (United States)

    Knight, B P; Chaudri, A M; McGrath, S P; Giller, K E

    1998-01-01

    A rapid method for extracting soil solutions using porous plastic soil-moisture samplers was combined with a cation resin equilibration based speciation technique to look at the chemical availability of metals in soil. Industrially polluted, metal sulphate amended and sewage sludge treated soils were used in our study. Cadmium sulphate amended and industrially contaminated soils all had > 65% of the total soil solution Cd present as free Cd2+. However, increasing total soil Cd concentrations by adding CdSO4 resulted in smaller total soil solution Cd. Consequently, the free Cd2+ concentrations in soil solutions extracted from these soils were smaller than in the same soil contaminated by sewage sludge addition. Amendment with ZnSO4 gave much greater concentrations of free Zn2+ in soil solutions compared with the same soil after long-term Zn contamination via sewage sludge additions. Our results demonstrate the difficulty in comparing total soil solution and free metal ion concentrations for soils from different areas with different physiochemical properties and sources of contamination. However, when comparing the same Woburn soil, Cd was much less available as Cd2+ in soil solution from the CdSO4 amended soils compared with soil contaminated by about 36 years of sewage sludge additions. In contrast, much more Zn was available in soil solution as free Zn2+ in the ZnSO4 amended soils compared with the sewage sludge treated soils.

  18. Determination of chemical content of PM10 and TSP using SEM-EDAX

    International Nuclear Information System (INIS)

    Masitah Alias; Zaini Hamzah

    2007-01-01

    The growing concern over the workers safety and health has lead many factories and organizations do the air monitoring to ensure the airborne at their workplace is safe for the worker's health and complying the Occupational Safety and Health Act 1994 (Act 514). In this study, the monitoring covers an indoor air quality and chemical exposure to the workers in one of the power plant repair shop. A few workers from different sections namely blasting, welding, grinding, fitting and maintenance area were chosen to assist in the personal monitoring for 8 hours measurement. PM10 were measured at a few sampling points to collect dusts for 24 hours duration. The samples were brought back to the laboratory for gravimetric and SEM-EDAX analysis. The results were certainly exceed the limit for air quality, and many elements were detected such as Fe, Ni, Al, Si, Ca, K, Ba, S, Cr, Zn and Cl. The present of these elements shows that exposure to these particulate matters is quite risky and some measure needs to be taken for remedial action. (Author)

  19. The chemical component dictionary: complete descriptions of constituent molecules in experimentally determined 3D macromolecules in the Protein Data Bank

    OpenAIRE

    Westbrook, John D.; Shao, Chenghua; Feng, Zukang; Zhuravleva, Marina; Velankar, Sameer; Young, Jasmine

    2014-01-01

    Summary: The Chemical Component Dictionary (CCD) is a chemical reference data resource that describes all residue and small molecule components found in Protein Data Bank (PDB) entries. The CCD contains detailed chemical descriptions for standard and modified amino acids/nucleotides, small molecule ligands and solvent molecules. Each chemical definition includes descriptions of chemical properties such as stereochemical assignments, chemical descriptors, systematic chemical names and idealize...

  20. Comparison of wet-chemical methods for determination of lipid hydroperoxides

    DEFF Research Database (Denmark)

    Nielsen, Nina Skall; Timm Heinrich, Maike; Jacobsen, Charlotte

    2003-01-01

    Five methods for determination of lipid hydroperoxides were evaluated, including two iodometric procedures involving a titration and a spectrophotometric micro method, and three other spectrophotometric methods namely the ferro, International Dairy Federation (IDF) and FOX2 (ferrous oxidation...... in xylenol orange). Peroxide values determined in a range of food products by these five methods gave different results. The ferro method required large amounts of solvent (50 mL/sample); the FOX2 method had a low range (0.005-0.04 mumol hydroperoxide); the end point detection of the titration method...... was subjective and required a large amount of sample (1 g); and the micro method was sensitive to interruptions during execution. Therefore, only the modified IDF method was chosen for further testing and validation. Stability tests of the standard curve showed a variation coefficient of 4% and within runs...

  1. Determination of uranium in the red blood cells of the workers in the chemical processing of uranium ore

    International Nuclear Information System (INIS)

    Nosek, J.; Simkova, M.; Kukula, F.; Musil, K.

    1975-04-01

    Neutron activation analysis was used in determining uranium in the venous blood erythrocytes of controls and of workers exposed to occupational hazards in a uranium chemical treatment plant. While 4.1 +- 2.6 ppb of uranium was found in dry matter of the erythrocytes in controls, 6.5 +- 2.1 ppb of uranium was ascertained in dry matter of the erythrocytes in occupationally exposed workers of a wet preparation plant, and 37.2 +- 20.2 ppb of uranium in the erythrocytes in workers of a dry cleaning plant. (author)

  2. A simple wet chemical method for the determination of cation stoichiometry of YBa2Cu3O7-d

    International Nuclear Information System (INIS)

    Sahasranaman, S.; Premila, M.; Sreedharan, O.M.

    1996-01-01

    A comprehensive wet chemical procedure for the rapid analysis of yttrium, barium and copper ions in dilute HNO 3 medium has been developed to facilitate a precise and accurate determination of cation non-stoichiometry in high temperature ceramic superconducting materials Y 1±x Ba 2±y Cu 3±z O 7-d . The ease of analysis for copper by electrogravimetry and of yttrium and barium by a complexometric titration of the same aliquot against complexone III using arsenazo I as the indicator under appropriate pH has been demonstrated with the help of individual standard solutions and with synthetic mixtures. (author)

  3. A ω-mercaptoundecylphosphonic acid chemically modified gold electrode for uranium determination in waters in presence of organic matter.

    Science.gov (United States)

    Merli, Daniele; Protti, Stefano; Labò, Matteo; Pesavento, Maria; Profumo, Antonella

    2016-05-01

    A chemically modified electrode (CME) on a gold surface assembled with a ω-phosphonic acid terminated thiol was investigated for its capability to complex uranyl ions. The electrode, characterized by electrochemical techniques, demonstrated to be effective for the determination of uranyl at sub-μgL(-1) level by differential pulse adsorptive stripping voltammetry (DPAdSV) in environmental waters, also in presence of humic matter and other potential chelating agents. The accuracy of the measurements was investigated employing as model probes ligands of different complexing capability (humic acids and EDTA). Copyright © 2016 Elsevier B.V. All rights reserved.

  4. APPRECIATION OF QUALITY FOR SOME TOMATOES VARIETIES BY USING THE DETERMINATION OF PHYSICAL-CHEMICAL PARAMETERS

    Directory of Open Access Journals (Sweden)

    Daniela Giosanu

    2016-12-01

    Full Text Available The studies were done on three varieties of tomatoes from Spain (red cherry, yellow cherry and kumato cherry. The following parameters: pH, soluble solids, content of water (moisture, content of minerals (ash, titratable acidity and content of some bioactive compounds (vitamin C, polyphenols, flavonoids, anthocyanins and carotenoids were determinate in order to appreciate the quality of these products. The results showed the influence of the varieties on the values of bioactive compounds with antioxidant activity.

  5. An optical chemical sensor for thorium (IV) determination based on thorin

    International Nuclear Information System (INIS)

    Rastegarzadeh, S.; Pourreza, N.; Saeedi, I.

    2010-01-01

    A selective method for the determination of thorium (IV) using an optical sensor is described. The sensing membrane is prepared by immobilization of thorin-methyltrioctylammonium ion pair on triacetylcellulose polymer. The sensor produced a linear response for thorium (IV) concentration in the range of 6.46 x 10 -6 to 9.91 x 10 -5 mol L -1 with detection limit of 1.85 x 10 -6 mol L -1 . The regeneration of optode was accomplished completely at a short time (less than 20 s) with 0.1 mol L -1 of oxalate ion solution. The relative standard deviation for ten replicate measurements of 2.15 x 10 -5 and 8.62 x 10 -5 mol L -1 of thorium was 2.71 and 1.65%, respectively. The optode membrane exhibits good selectivity for thorium (IV) over several other ionic species and are comparable to those obtained in case of spectrophotometric determination of thorium using thorin in solution. A good agreement with the ICP-MS and spiked method was achieved when the proposed optode was applied to the determination of thorium (IV) in dust and water samples.

  6. An optical chemical sensor for thorium (IV) determination based on thorin.

    Science.gov (United States)

    Rastegarzadeh, S; Pourreza, N; Saeedi, I

    2010-01-15

    A selective method for the determination of thorium (IV) using an optical sensor is described. The sensing membrane is prepared by immobilization of thorin-methyltrioctylammonium ion pair on triacetylcellulose polymer. The sensor produced a linear response for thorium (IV) concentration in the range of 6.46 x 10(-6) to 9.91 x 10(-5)mol L(-1) with detection limit of 1.85 x 10(-6)mol L(-1). The regeneration of optode was accomplished completely at a short time (less than 20s) with 0.1 mol L(-1) of oxalate ion solution. The relative standard deviation for ten replicate measurements of 2.15 x 10(-5) and 8.62 x 10(-5)mol L(-1) of thorium was 2.71 and 1.65%, respectively. The optode membrane exhibits good selectivity for thorium (IV) over several other ionic species and are comparable to those obtained in case of spectrophotometric determination of thorium using thorin in solution. A good agreement with the ICP-MS and spiked method was achieved when the proposed optode was applied to the determination of thorium (IV) in dust and water samples.

  7. Method validation for chemical composition determination by electron microprobe with wavelength dispersive spectrometer

    Science.gov (United States)

    Herrera-Basurto, R.; Mercader-Trejo, F.; Muñoz-Madrigal, N.; Juárez-García, J. M.; Rodriguez-López, A.; Manzano-Ramírez, A.

    2016-07-01

    The main goal of method validation is to demonstrate that the method is suitable for its intended purpose. One of the advantages of analytical method validation is translated into a level of confidence about the measurement results reported to satisfy a specific objective. Elemental composition determination by wavelength dispersive spectrometer (WDS) microanalysis has been used over extremely wide areas, mainly in the field of materials science, impurity determinations in geological, biological and food samples. However, little information is reported about the validation of the applied methods. Herein, results of the in-house method validation for elemental composition determination by WDS are shown. SRM 482, a binary alloy Cu-Au of different compositions, was used during the validation protocol following the recommendations for method validation proposed by Eurachem. This paper can be taken as a reference for the evaluation of the validation parameters more frequently requested to get the accreditation under the requirements of the ISO/IEC 17025 standard: selectivity, limit of detection, linear interval, sensitivity, precision, trueness and uncertainty. A model for uncertainty estimation was proposed including systematic and random errors. In addition, parameters evaluated during the validation process were also considered as part of the uncertainty model.

  8. Determinants of Exposure to Fragranced Product Chemical Mixtures in a Sample of Twins

    Directory of Open Access Journals (Sweden)

    Matthew O. Gribble

    2015-01-01

    Full Text Available Fragranced product chemical mixtures may be relevant for environmental health, but little is known about exposure. We analyzed results from an olfactory challenge with the synthetic musk fragrance 1,3,4,6,7,8-hexahydro-4,6,6,7,8,8-hexamethyl-cyclopento-γ-2-benzopyran (HHCB, and a questionnaire about attitudes toward chemical safety and use of fragranced products, in a sample of 140 white and 17 black twin pairs attending a festival in Ohio. Data for each product were analyzed using robust ordered logistic regressions with random intercepts for “twin pair” and “sharing address with twin”, and fixed effects for sex, age, education, and “ever being bothered by fragrances”. Due to the small number of black participants, models were restricted to white participants except when examining racial differences. Overall patterns of association were summarized across product-types through random-effects meta-analysis. Principal components analysis was used to summarize clustering of product use. The dominant axis of variability in fragranced product use was “more vs. less”, followed by a distinction between household cleaning products and personal care products. Overall, males used fragranced products less frequently than females (adjusted proportionate odds ratio 0.55, 95% confidence interval 0.33, 0.93. This disparity was driven by personal care products (0.42, 95% CI: 0.19, 0.96, rather than household cleaning products (0.79, 95% CI: 0.49, 1.25 and was particularly evident for body lotion (0.12, 95% CI: 0.05, 0.27. Overall usage differed by age (0.64, 95% CI: 0.43, 0.95 but only hand soap and shampoo products differed significantly. “Ever being bothered by fragrance” had no overall association (0.92, 95% CI: 0.65, 1.30 but was associated with laundry detergent use (0.46, 95% CI: 0.23, 0.93. Similarly, black vs. white differences on average were not significant (1.34, 95% CI: 0.55, 3.28 but there were apparent differences in use of

  9. Determinants of Exposure to Fragranced Product Chemical Mixtures in a Sample of Twins

    Science.gov (United States)

    Gribble, Matthew O.; Bandeen-Roche, Karen; Fox, Mary A.

    2015-01-01

    Fragranced product chemical mixtures may be relevant for environmental health, but little is known about exposure. We analyzed results from an olfactory challenge with the synthetic musk fragrance 1,3,4,6,7,8-hexahydro-4,6,6,7,8,8-hexamethyl-cyclopento-γ-2-benzopyran (HHCB), and a questionnaire about attitudes toward chemical safety and use of fragranced products, in a sample of 140 white and 17 black twin pairs attending a festival in Ohio. Data for each product were analyzed using robust ordered logistic regressions with random intercepts for “twin pair” and “sharing address with twin”, and fixed effects for sex, age, education, and “ever being bothered by fragrances”. Due to the small number of black participants, models were restricted to white participants except when examining racial differences. Overall patterns of association were summarized across product-types through random-effects meta-analysis. Principal components analysis was used to summarize clustering of product use. The dominant axis of variability in fragranced product use was “more vs. less”, followed by a distinction between household cleaning products and personal care products. Overall, males used fragranced products less frequently than females (adjusted proportionate odds ratio 0.55, 95% confidence interval 0.33, 0.93). This disparity was driven by personal care products (0.42, 95% CI: 0.19, 0.96), rather than household cleaning products (0.79, 95% CI: 0.49, 1.25) and was particularly evident for body lotion (0.12, 95% CI: 0.05, 0.27). Overall usage differed by age (0.64, 95% CI: 0.43, 0.95) but only hand soap and shampoo products differed significantly. “Ever being bothered by fragrance” had no overall association (0.92, 95% CI: 0.65, 1.30) but was associated with laundry detergent use (0.46, 95% CI: 0.23, 0.93). Similarly, black vs. white differences on average were not significant (1.34, 95% CI: 0.55, 3.28) but there were apparent differences in use of shampoo (0

  10. Chemical compositions of subway particles in Seoul, Korea determined by a quantitative single particle analysis.

    Science.gov (United States)

    Kang, Sunni; Hwang, HeeJin; Park, YooMyung; Kim, HyeKyoung; Ro, Chul-Un

    2008-12-15

    A novel single particle analytical technique, low-Z particle electron probe X-ray microanalysis, was applied to characterize seasonal subway samples collected at a subway station in Seoul, Korea. For all 8 samples collected twice in each season, 4 major types of subway particles, based on their chemical compositions, are significantly encountered: Fe-containing; soil-derived; carbonaceous; and secondary nitrate and/or sulfate particles. Fe-containing particles are generated indoors from wear processes at rail-wheel-brake interfaces while the others may be introduced mostly from the outdoor urban atmosphere. Fe-containing particles are the most frequently encountered with relative abundances in the range of 61-79%. In this study, it is shown that Fe-containing subway particles almost always exist either as partially or fully oxidized forms in underground subway microenvironments. Their relative abundances of Fe-containing particles increase as particle sizes decrease. Relative abundances of Fe-containing particles are higher in morning samples than in afternoon samples because of heavier train traffic in the morning. In the summertime samples, Fe-containing particles are the most abundantly encountered, whereas soil-derived and nitrate/sulfate particles are the least encountered, indicating the air-exchange between indoor and outdoor environments is limited in the summer, owing to the air-conditioning in the subway system. In our work, it was observed that the relative abundances of the particles of outdoor origin vary somewhat among seasonal samples to a lesser degree, reflecting that indoor emission sources predominate.

  11. Determination of chemical parameters for the Schlema-Alberoda uranium tailings pile migration case study

    International Nuclear Information System (INIS)

    Bryan, N.; Vopalka, D.; Benes, P.; Stamberg, K.; Doubravova, K.

    2004-01-01

    A central aim of environmental chemistry is to develop an understanding of processes at the microscopic level, and to develop speciation models to simulate that behaviour, which may be used with transport codes to predict the fate of pollutants on the field scale. In fact, one objective of this HUPA project is to develop a coupled chemical transport computer code, which includes the effects of humic substances, and then apply it to three field scale test cases: 1. a deep hypothetical repository in a salt formation; 2. a shallow, sandy hypothetical repository; 3. a large pile of uranium mine tailings. This work concerns the third case study (U-tailings), which is based upon a real U-tailings pile at Schlema-Alberoda, near Dresden, Saxony, Germany. Environmental problems are inherently complex, and even apparently simple systems, such as a single metal ion interacting with a 'single' surface may be extremely complex. There have been considerable advances in computing power over the last few decades, unfortunately, in order to make calculations solvable in a reasonable time, the models used to simulate the chemistry of the system must be as simple as possible. The interaction between uranium and humic substances has been studied previously. However, the details of the interaction of uranyl cations with the material of the pile have not been modelled. Therefore, the objective here is to develop a simple model of this interaction, ready to use in the migration case study. Experiments were performed at the Czech Technical University, Prague and the data modelled at the University of Manchester. (orig.)

  12. Determination of the chemical properties of residues retained in individual cloud droplets by XRF microprobe at SPring-8

    International Nuclear Information System (INIS)

    Ma, C.-J.; Tohno, S.; Kasahara, M.; Hayakawa, S.

    2004-01-01

    To determine the chemical properties of residue retained in individual cloud droplets is primarily important for the understanding of rainout mechanism and aerosol modification in droplet. The sampling of individual cloud droplets were carried out on the summit of Mt. Taiko located in Tango peninsula, Kyoto prefecture, during Asian dust storm event in March of 2002. XRF microprobe system equipped at SPring-8, BL-37XU was applied to the subsequent quantification analysis of ultra trace elements in residues of individual cloud droplets. It was possible to form the replicas of separated individual cloud droplets on the thin collodion film. The two dimensional XRF maps for the residues in individual cloud droplets were clearly drawn by scanning of micro-beam. Also, XRF spectra of trace elements in residues were well resolved. From the XRF spectra for individual residues, the chemical mixed state of residues could be assumed. The chemical forms of Fe (Fe +++ ) and Zn (Zn + ) could be clearly characterized by their K-edge micro-XANES spectra. By comparison of Z/Si mass ratios of residues in cloud droplets and those of the original sands collected in desert areas in China, the aging of ambient dust particles and their in cloud modification were indirectly assumed

  13. Review of analytical techniques to determine the chemical forms of vapours and aerosols released from overheated fuel

    International Nuclear Information System (INIS)

    Bowsher, B.R.; Nichols, A.L.

    1989-12-01

    A comprehensive review has been undertaken of appropriate analytical techniques to monitor and measure the chemical effects that occur in large-scale tests designed to study severe reactor accidents. Various methods have been developed to determine the chemical forms of the vapours, aerosols and deposits generated during and after such integral experiments. Other specific techniques have the long-term potential to provide some of the desired data in greater detail, although considerable efforts are still required to apply these techniques to the study of radioactive debris. Such in-situ and post-test methods of analysis have been also assessed in terms of their applicability to the analysis of samples from the Phebus-FP tests. The recommended in-situ methods of analysis are gamma-ray spectroscopy, potentiometry, mass spectrometry, and Raman/UV-visible absorption spectroscopy. Vapour/aerosol and deposition samples should also be obtained at well-defined time intervals during each experiment for subsequent post-test analysis. No single technique can provide all the necessary chemical data from these samples, and the most appropriate method of analysis involves a complementary combination of autoradiography, AES, IR, MRS, SEMS/EDS, SIMS/LMIS, XPS and XRD

  14. Composição química e rendimento da carne ovina in natura e assada Chemical composition and yield of in natura and roast sheep meat

    Directory of Open Access Journals (Sweden)

    Rafael Silvio Bonilha Pinheiro

    2008-12-01

    Full Text Available Utilizou-se o músculo Triceps brachii de cordeiros não castrados ½ Ile de France ½ Santa Inês terminados em confinamento para a realização das análises físico-químicas. Foram determinados: a umidade, a proteína, a gordura, as cinzas e os carboidratos da carne, in natura e assada, destes animais, assim como o rendimento desta carne, após o processo de cocção. A carne assada apresentou valores maiores de gordura e proteína (7,49 e 33,67% em comparação com a carne in natura (5,36 e 18,85%, respectivamente. Os percentuais de cinzas e carboidratos não foram influenciados pelos tratamentos estudados, porém para os valores de umidade, a carne in natura obteve valores superiores ao da carne assada, 74,05 e 57,02%, respectivamente. A carne assada teve perdas durante o seu preparo por evaporação, por gotejamento e por cocção de 33,20, 1,36 e 35,20%, respectivamente. Concluiu-se que a carne assada apresenta valor nutricional mais elevado que a carne in natura, para os teores de gordura e proteína, pelo fato da carne in natura apresentar maior valor de umidade em relação à assada, ocasionando assim a concentração de gordura e de proteína na carne assada. O preparo da carne ocasionou perdas por cocção de 35,20%, por gotejamento e evaporação.Tríceps brachii muscle from non-castrated ½ Ile de France ½ Santa Inês lambs terminated in confinement was used for physical and chemical analyses. In natura and roast meat moisture, protein, fat, ashes, carbohydrates, and meat yield were determined after the cooking process. Roast meat presented higher fat and protein values (7,49 and 33,67%, compared to in natura meat (5,36 and 18,85%, respectively. Ashes and carbohydrates percentages were not influenced by the treatments studied; however, in natura meat presented higher moisture values than roast meat (74,05 and 57,02%, respectively. Roast meat presented losses of 33, 20, 1,36, and 35,20% from evaporation, dripping, and cooking

  15. Determination of Psub(K) values to the 172, 103 and 97 keV levels and the fluorescence yield. omega. sub(K) of Eu after electron capture by /sup 153/Gd

    Energy Technology Data Exchange (ETDEWEB)

    Singh, K; Grewal, B S; Sahota, H S [Punjabi Univ., Patiala (India). Dept. of Physics

    1985-03-01

    From an analysis of K x-ray-..gamma..-ray sum peaks observed with an intrinsic Ge detector the K-capture probabilities (Psub(K)) to the 172, 103 and 97 keV levels in the decay of /sup 153/Gd have been determined; these yield an electron-capture energy Qsub(EC)=245 +- 2. The K-capture probability to the 172 keV level differs significantly from that found in the literature. With these results the K-shell fluorescence yield of Eu is ..omega..sub(K)=0.935 +- 0.019.

  16. ICP-AES determination of rare earths in zirconium with prior chemical separation of the matrix

    International Nuclear Information System (INIS)

    Rajeswari, B.; Dhawale, B.A.; Page, A.G.; Sastry, M.D.

    2002-01-01

    Zirconium being one of the most important material in nuclear industry used as a fuel cladding in reactors and an additive in advanced fuels necessitates its characterization for trace metallic contents. Zirconium, as refractory in nature as the rare earth elements, has a complex spectrum comprising of several emission lines. Rare earths, which are high neutron absorbers have to be analysed at very low limits. Hence, to achieve the desired limits, the major matrix has to be separated prior to rare earth determination. The present paper describes the method developed for the separation of rare earths from zirconium by solvent extraction using Trioctyl Phosphine Oxide (TOPO) as the extractant followed by their determination using Inductively Coupled Plasma - Atomic Emission Spectrometric (ICP-AES) method. Initially, radiochemical studies were carried out using known amounts of gamma active tracers of 141 Ce, 152-154 Eu, 153 Gd and 95 Zr for optimisation of extraction conditions using Tl- activated NaI detector. The optimum conditions at 0.5 M TOPO/xylene in 6 M HCl so as to achieve a quantitative recovery of rare earth analytes alongwith a near total extraction of zirconium in the organic phase, was further extended to carry out the studies using ICP-AES method. The recovery of rare earths was found to be quantitative within experimental error with a precision better than 10% RSD. (author)

  17. Yield, chemical composition, in vitro digestibility and

    African Journals Online (AJOL)

    reza

    To provide balanced diets that include straw, it is important to know the nutritive value .... (2005) and Anderson & Hoffman (2006). .... the accuracy of voluntary DMI prediction of temperate, tropical crop residues and Mediterranean hays.

  18. Determination of chemical composition, and storage on dried fermented goat milk product (Oggtt

    Directory of Open Access Journals (Sweden)

    Badriah O. Al-Abdulkarim

    2013-06-01

    Full Text Available A sample of dried fermented goat milk product (Oggtt obtained from the local market of Riyadh city in The Kingdom of Saudi Arabia, was stored for 6 months at 4 °C and subjected to chemical composition analysis before and after storage. The result showed that the sample moisture increased significantly (P ⩽ 0.05 after storage from 7% to 10%, total ash decreased non-significantly (P ⩽ 0.05 from 8% to 7.6%, total carbohydrates decreased non-significantly (P ⩽ 0.05 from 35.5% to 33.8%, protein increased non-significantly (P ⩽ 0.05 from 16 to 16.1 g/l, fat content was found to have the same values in all samples before and after storage at 5%, lactose increased (P ⩽ 0.05 non-significantly from 28.4% to 29%, acidity decreased (P ⩽ 0.05 significantly from 0.45% to 0.39%, and pH decreased (P ⩽ 0.05 non-significantly from 4.3% to 4%. On the other hand, mineral composition showed (P ⩽ 0.05 non-significant results before and after storage. Ca concentration decreased from 118 to 1149 mg/kg and K concentration increased from 185.8 to 1888 mg/kg. While Mg increased from 105 to 123 mg/kg, Zn increased from 8.3 to 8.6 mg/kg, Mn and Fe were found to have the same values of concentrations before and after storage which were 0.2 and 0.1 mg/kg, respectively. Accordingly, we can conclude that Oggtt is a stable product and have a good nutritional value in comparison to daily required amounts for healthy human life.

  19. Standard Test Method to Determine Color Change and Staining Caused by Aircraft Maintenance Chemicals upon Aircraft Cabin Interior Hard Surfaces

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2001-01-01

    1.1 This test method covers the determination of color change and staining from liquid solutions, such as cleaning or disinfecting chemicals or both, on painted metallic surfaces and nonmetallic surfaces of materials being used inside the aircraft cabin. The effects upon the exposed specimens are measured with the AATCC Gray Scale for Color Change and AATCC Gray Color Scale for Staining. Note 1—This test method is applicable to any colored nonmetallic hard surface in contact with liquids. The selected test specimens are chosen because these materials are present in the majority of aircraft cabin interiors. 1.2This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  20. The chemical nature of phenolic compounds determines their toxicity and induces distinct physiological responses in Saccharomyces cerevisiae in lignocellulose hydrolysates

    Science.gov (United States)

    2014-01-01

    We investigated the severity of the inhibitory effects of 13 phenolic compounds usually found in spruce hydrolysates (4-hydroxy-3-methoxycinnamaldehyde, homovanilyl alcohol, vanillin, syringic acid, vanillic acid, gallic acid, dihydroferulic acid, p-coumaric acid, hydroquinone, ferulic acid, homovanillic acid, 4-hydroxybenzoic acid and vanillylidenacetone). The effects of the selected compounds on cell growth, biomass yield and ethanol yield were studied and the toxic concentration threshold was defined for each compound. Using Ethanol Red, the popular industrial strain of Saccharomyces cerevisiae, we found the most toxic compound to be 4-hydroxy-3-methoxycinnamaldehyde which inhibited growth at a concentration of 1.8 mM. We also observed that toxicity did not generally follow a trend based on the aldehyde, acid, ketone or alcohol classification of phenolic compounds, but rather that other structural properties such as additional functional groups attached to the compound may determine its toxicity. Three distinctive growth patterns that effectively clustered all the compounds involved in the screening into three categories. We suggest that the compounds have different cellular targets, and that. We suggest that the compounds have different cellular targets and inhibitory mechanisms in the cells, also compounds who share similar pattern on cell growth may have similar inhibitory effect and mechanisms of inhibition. PMID:24949277

  1. Sequential path analysis for determining interrelationships between yield and related traits in tobacco (Nicotiana tabacum L. under normal and abiotic stress conditions

    Directory of Open Access Journals (Sweden)

    Bayat Mahdi

    2014-01-01

    Full Text Available In the present work the relationships between yield and its related traits were investigated in tobacco genotypes under normal and abiotic stress conditions (Orobanche aegyptiaca weed at Urmia Tobacco Research Centre, Iran, during 2006-2009 cropping seasons. The experimental design was a randomized complete block design (RCBD with three replications in each condition every year. Analysis of variance revealed extent genetic variability among the genotypes for most of the traits studied. In comparison with normal condition, the mean value of studied traits decreased in stress condition. LAI and FD showed the maximum and minimum diminution in the mean values under stress condition compared to normal one so known as more sensitive and more tolerant traits, respectively. Based on CV values, the traits FD and DLYP showed the minimum and maximum variation among traits in both normal and stress conditions. Correlation analysis revealed significant and positive correlations between DLYP with all studied traits in both normal and stress conditions. Path analysis detected the traits including biomass, APDW and DWR as the first-order variables at normal condition and biomass, APDW, DWR and harvest index as the first-order variables under abiotic stress condition. Based on results, the traits such as biomass, APDW, DWR detected as more important factors in both conditions can be used in tobacco breeding programs for increasing yield. Abbreviation: aerial part fresh weight without leaves weight (APFW, aerial part dry weight without leaves weight (APDW, biomass (BIO, coefficient of variation (CV, dry weight of root (DWR, flowering date (FD, fresh weight of leaf (FWL, fresh weight of root (FWR, harvest index (HI, leaf area index (LAI, dry leaf yield per plant (DLYP, number of leaf (NL, plant height (PH, randomized complete block design (RCBD, standard deviation (Std.

  2. Determination of decimal reduction time (D value) of chemical agents used in hospitals for disinfection purposes

    Science.gov (United States)

    Mazzola, Priscila Gava; Penna, Thereza Christina Vessoni; da S Martins, Alzira M

    2003-01-01

    Background Prior to the selection of disinfectants for low, intermediate and high (sterilizing) levels, the decimal reduction time, D-value, for the most common and persistent bacteria identified at a health care facility should be determined. Methods The D-value was determined by inoculating 100 mL of disinfecting solution with 1 mL of a bacterial suspension (104 – 105 CFU/mL for vegetative and spore forms). At regular intervals, 1 mL aliquots of this mixture were transferred to 8 mL of growth media containing a neutralizing agent, and incubated at optimal conditions for the microorganism. Results The highest D-values for various bacteria were determined for the following solutions: (i) 0.1% sodium dichloroisocyanurate (pH 7.0) – E. coli and A. calcoaceticus (D = 5.9 min); (ii) sodium hypochlorite (pH 7.0) at 0.025% for B. stearothermophilus (D = 24 min), E. coli and E. cloacae (D = 7.5 min); at 0.05% for B. stearothermophilus (D = 9.4 min) and E. coli (D = 6.1 min) and 0.1% for B. stearothermophilus (D = 3.5 min) and B. subtilis (D = 3.2 min); (iii) 2.0% glutaraldehyde (pH 7.4) – B. stearothermophilus, B. subtilis (D = 25 min) and E. coli (D = 7.1 min); (iv) 0.5% formaldehyde (pH 6.5) – B. subtilis (D = 11.8 min), B. stearothermophilus (D = 10.9 min) and A. calcoaceticus (D = 5.2 min); (v) 2.0% chlorhexidine (pH 6.2) – B. stearothermophilus (D = 9.1 min), and at 0.4% for E. cloacae (D = 8.3 min); (vi) 1.0% Minncare® (peracetic acid and hydrogen peroxide, pH 2.3) – B. stearothermophilus (D = 9.1 min) and E. coli (D = 6.7 min). Conclusions The suspension studies were an indication of the disinfectant efficacy on a surface. The data in this study reflect the formulations used and may vary from product to product. The expected effectiveness from the studied formulations showed that the tested agents can be recommended for surface disinfection as stated in present guidelines and emphasizes the importance and need to develop routine and novel programs to

  3. Determination of decimal reduction time (D value of chemical agents used in hospitals for disinfection purposes

    Directory of Open Access Journals (Sweden)

    da S Martins Alzira M

    2003-10-01

    Full Text Available Abstract Background Prior to the selection of disinfectants for low, intermediate and high (sterilizing levels, the decimal reduction time, D-value, for the most common and persistent bacteria identified at a health care facility should be determined. Methods The D-value was determined by inoculating 100 mL of disinfecting solution with 1 mL of a bacterial suspension (104 – 105 CFU/mL for vegetative and spore forms. At regular intervals, 1 mL aliquots of this mixture were transferred to 8 mL of growth media containing a neutralizing agent, and incubated at optimal conditions for the microorganism. Results The highest D-values for various bacteria were determined for the following solutions: (i 0.1% sodium dichloroisocyanurate (pH 7.0 – E. coli and A. calcoaceticus (D = 5.9 min; (ii sodium hypochlorite (pH 7.0 at 0.025% for B. stearothermophilus (D = 24 min, E. coli and E. cloacae (D = 7.5 min; at 0.05% for B. stearothermophilus (D = 9.4 min and E. coli (D = 6.1 min and 0.1% for B. stearothermophilus (D = 3.5 min and B. subtilis (D = 3.2 min; (iii 2.0% glutaraldehyde (pH 7.4 – B. stearothermophilus, B. subtilis (D = 25 min and E. coli (D = 7.1 min; (iv 0.5% formaldehyde (pH 6.5 – B. subtilis (D = 11.8 min, B. stearothermophilus (D = 10.9 min and A. calcoaceticus (D = 5.2 min; (v 2.0% chlorhexidine (pH 6.2 – B. stearothermophilus (D = 9.1 min, and at 0.4% for E. cloacae (D = 8.3 min; (vi 1.0% Minncare® (peracetic acid and hydrogen peroxide, pH 2.3 – B. stearothermophilus (D = 9.1 min and E. coli (D = 6.7 min. Conclusions The suspension studies were an indication of the disinfectant efficacy on a surface. The data in this study reflect the formulations used and may vary from product to product. The expected effectiveness from the studied formulations showed that the tested agents can be recommended for surface disinfection as stated in present guidelines and emphasizes the importance and need to develop routine and novel programs to

  4. Determination and comparison of chemical characteristics of Arbutus unedo L. and Arbutus andrachnae L. (family Ericaceae) fruits.

    Science.gov (United States)

    Seker, Murat; Toplu, Celil

    2010-08-01

    The fruits and leaves of Arbutus species are well known in folk medicine as antiseptics, diuretics, and laxatives in many parts of Turkey. Some chemical properties including pH, soluble solid content, titratable acidity, protein, moisture, ash, ascorbic acid, fructose, glucose, sucrose, total phenols, total antioxidant activity, and minerals were determined in fully matured Arbutus unedo L. and Arbutus andrachnae L. fruits collected from different sites of Canakkale, Turkey in 2006 and 2007. Total soluble solids, titratable acidity, protein, moisture, and ash content of A. unedo and A. andrachnae berries were on average 16.0% and 14.0%, 0.4% and 0.6%, 2.38% and 3.77%, 47.21% and 38.21%, and 2.82% and 4.35%, respectively. The mean values of ascorbic acid were 270.50 mg/100 g for A. unedo and 140.30 mg/100 g for A. andrachnae, which suggested that Arbutus berries contain high amounts of vitamin C. In the strawberry tree fruits, fructose and glucose were determined to be the major sugars. The analysis showed that fructose and glucose occurred in concentrations of 24.09% and 19.09%, respectively. However, ripe A. andrachnae fruits contained small amounts of fructose (4.12%), glucose (2.73%), and sucrose (0.16%) detectable by high-performance liquid chromatography analysis. The general order of abundance of the minerals was K > Ca > P > Mg > Na in whole fruit of the strawberry tree. The chemical composition of Arbutus fruits indicates that the fruits are good sources of minerals and ascorbic acid and that they are high in phenolics and antioxidant capacity and low in soluble sugars, especially A. andrachnae. The data should be useful for research purposes and for compiling local food composition tables. In view of its chemical composition, the use of Arbutus fruits in some food products may be suggested.

  5. Chemical interactions in complex matrices: Determination of polar impurities in biofuels and fuel contaminants in building materials

    Science.gov (United States)

    Baglayeva, Ganna

    The solutions to several real-life analytical and physical chemistry problems, which involve chemical interactions in complex matrices are presented. The possible interferences due to the analyte-analyte and analyte-matrix chemical interactions were minimized on each step of the performed chemical analysis. Concrete and wood, as major construction materials, typically become contaminated with fuel oil hydrocarbons during their spillage. In the catastrophic scenarios (e.g., during floods), fuel oil mixes with water and then becomes entrained within the porous structure of wood or concrete. A strategy was proposed for the efficient extraction of fuel oil hydrocarbons from concrete to enable their monitoring. The impacts of sample aging and inundation with water on the extraction efficiency were investigated to elucidate the nature of analytematrix interactions. Two extraction methods, 4-days cold solvent extraction with shaking and 24-hours Soxhlet extraction with ethylacetate, methanol or acetonitrile yielded 95-100 % recovery of fuel oil hydrocarbons from concrete. A method of concrete remediation after contamination with fuel oil hydrocarbons using activated carbon as an adsorbent was developed. The 14 days remediation was able to achieve ca. 90 % of the contaminant removal even from aged water-submerged concrete samples. The degree of contamination can be qualitatively assessed using transport rates of the contaminants. Two models were developed, Fickian and empirical, to predict long-term transport behavior of fuel oil hydrocarbons under flood representative scenarios into wood. Various sorption parameters, including sorption rate, penetration degree and diffusion coefficients were obtained. The explanations to the observed three sorption phases are provided in terms of analyte-matrix interactions. The detailed simultaneous analysis of intermediate products of the cracking of triacylglycerol oils, namely monocarboxylic acids, triacyl-, diacyl- and

  6. Error estimation and global fitting in transverse-relaxation dispersion experiments to determine chemical-exchange parameters

    International Nuclear Information System (INIS)

    Ishima, Rieko; Torchia, Dennis A.

    2005-01-01

    Off-resonance effects can introduce significant systematic errors in R 2 measurements in constant-time Carr-Purcell-Meiboom-Gill (CPMG) transverse relaxation dispersion experiments. For an off-resonance chemical shift of 500 Hz, 15 N relaxation dispersion profiles obtained from experiment and computer simulation indicated a systematic error of ca. 3%. This error is three- to five-fold larger than the random error in R 2 caused by noise. Good estimates of total R 2 uncertainty are critical in order to obtain accurate estimates in optimized chemical exchange parameters and their uncertainties derived from χ 2 minimization of a target function. Here, we present a simple empirical approach that provides a good estimate of the total error (systematic + random) in 15 N R 2 values measured for the HIV protease. The advantage of this empirical error estimate is that it is applicable even when some of the factors that contribute to the off-resonance error are not known. These errors are incorporated into a χ 2 minimization protocol, in which the Carver-Richards equation is used fit the observed R 2 dispersion profiles, that yields optimized chemical exchange parameters and their confidence limits. Optimized parameters are also derived, using the same protein sample and data-fitting protocol, from 1 H R 2 measurements in which systematic errors are negligible. Although 1 H and 15 N relaxation profiles of individual residues were well fit, the optimized exchange parameters had large uncertainties (confidence limits). In contrast, when a single pair of exchange parameters (the exchange lifetime, τ ex , and the fractional population, p a ), were constrained to globally fit all R 2 profiles for residues in the dimer interface of the protein, confidence limits were less than 8% for all optimized exchange parameters. In addition, F-tests showed that quality of the fits obtained using τ ex , p a as global parameters were not improved when these parameters were free to fit the R

  7. Determination of heavy metal content and physico-chemical properties of soils in the vicinity of Tasik Chini, Pahang

    International Nuclear Information System (INIS)

    Sahibin Abdul Rahim; Muhd Barzani Gasim; Mohd Nizam Mohd Said; Wan Mohd Razi Idris; Azman Hashim; Sharilnizam Yusof; Masniyana Jamil

    2008-01-01

    This study was carried out to determine heavy metal content and physico-chemical properties of soils influencing heavy metal accumulation in some series surrounding the Chini Lakes. A total of 15 topsoil sample were collected randomly from 6 stations. The physical properties that were analyzed include particle size distribution and soil organic matter. Meanwhile, the chemical characteristics determined were pH, electrical conductivity and cation exchange capacity. It was found that heavy metal content of Cd, Cr, Cu, Co, Pb, Zn and Mn were low whereas Fe content was high. The textures of soil studied were clay, loamy sand, sandy loam, clay loam and silty clay loam. The mean of organic matter ranged from 2.68 to 11.46 %. The soil pH showed that the soil studied was acidic with values ranged between 3.36 to 3.72. The range of electrical conductivity mean was between 2150 μScm -1 to 2403 μScm -1 . Cation exchange capacity mean ranged from 2.85 until 8.59 cmol/ kg. Correlation analysis showed that there were positive and negative significant correlations between soils parameters heavy metal concentration. Analysis of variance (ANOVA) showed that there were significant differences in organic matter percentage, pH, cation exchange capacity and heavy metals except cadmium between sampling station. (author)

  8. Evaluation of Chemical and Physical-morphological Factors as Potential Determinants of Biomphalaria pfeifferi (Krauss, 1848 Distribution

    Directory of Open Access Journals (Sweden)

    Utzinger Jürg

    1997-01-01

    Full Text Available This study was carried out in five sites along a small perennial river system in south-central Tanzania, which had been identified as the focus for transmission of intestinal schistosomiasis in the area. Malacological surveys preceding the study showed a focal distribution of Biomphalaria pfeifferi, intermediate host snail of Schistosoma mansoni, the snails being present in three sites but absent from the other two sites. The objective of this study was to evaluate to what extent chemical and/or physical-morphological factors determine the distribution of B. pfeifferi between these five sites. It was found that none of the chemical constituents in the waters examined were outside the tolerance range of B. pfeifferi snails. Moreover, the composition of water from B. pfeifferi-free sites was not different from that in those sites where snails occurred. Furthermore, none of the physical-morphological constituents seemed likely to be a determinant for the absence of B. pfeifferi. In view of these findings, and those of previous studies, it is concluded that the focal distribution of B. pfeifferi cannot be associated with a single environmental factor and is rather the result of more complex interactions of habitat factors

  9. Determination of mixing characteristics of the river Kabul and the river Indus using physico-chemical and stable isotope parameters

    International Nuclear Information System (INIS)

    Qureshi, R.M.; Hussain, Q.M.; Sajjad, M.I.; Hussain, S.D.; Latif, Z.

    1990-11-01

    This report presents a comparative study on the usefulness of stable isotope parameters (hydrogen and oxygen) versus the physico-chemical parameters (electrical conductivity, temperature, pH value) of water to determine the extent of mixing of the river Kabul with the river Indus near Attock. In view of the sampling techniques employed in the present investigations, electrical conductivity and temperature are found to be the best field parameters for a quick estimate of mixing path length. However, the stable isotopes of the water molecule, due to their greater sensitivity and measuring accuracy, provide a better scenario of mixing characteristics as compared to the physico-chemical parameters. It appears that under normal flow condition, it takes about 5 km channel distance for complete mixing of the Kabul river water in the Indus river channel. A computer code MIXABC is developed to determine the percentage contribution of one river water along a mixing channel in the other river. Details of the source programs are presented. The code can be used on any IBM-compatible microsystem. (author)

  10. CHEMICAL DETERMINATION OF HEAVY METALS IN PB AND ZN CONCENTRATES OF TREPÇA (KOSOVO AND CORRELATIONS COEFFI CIENTS STUDY BETWEEN CHEMICAL DATA

    Directory of Open Access Journals (Sweden)

    Fatbardh Gashi

    2017-03-01

    Full Text Available Kosovo ore deposits are located in the Trepça belt which extends for over 80 km. The concentrate produced by the flotation process of the Trepça metallurgical corporation contains a considerable quantity of valuable metals, such as Pb, Zn, Fe and minor accompanying metals such as Cd, Cu, As, Sb, Bi, Ag, Au, etc. The subject of this work was to assess the concentration of major and minor metals in lead and zinc concentrates of Trepça and to study the correlation coefficients between metals. Chemical determination of concentrates was performed by using atomic absorption spectroscopy (AAS. In the content on lead concentrate samples, the following were found: Pb>Fe>Zn> Ag> As>Sb>Cd. In the content of zinc concentrate, the following were found: Zn>Fe>Pb>Ag>As>Cd. The program “Statistica ver. 6.0” has been used for calculations of basic statistical parameters, relationships between data and cluster analysis of R-mode. R-mode cluster analysis on lead concentrate samples showed that Pb has the closest linkages with Fe and they form one branch of the dendogram. On the zinc concentrate samples, Zn has the closest linkages with Fe and they form one branch of the dendogram.

  11. Determination of phosphorus in metals by neutron activation and chemical separation as hydride

    International Nuclear Information System (INIS)

    Rouchaud, J.C.; Fedoroff, M.

    1993-01-01

    Phosphorous at trace levels alters the properties of metals and alloys. Its determination was investigated by radiochemical neutron activation analysis. Separation by solvent extraction or by evolution as P 0 showed to be neither selective nor quantitative in presence of a metallic matrix. Therefore, a new method of separation by reduction to phosphorous hydride followed by liquid scintillation counting was investigated. This method is quantitative in the case of non-radioactive iron doped with radioactive phosphorus. At present, the separation is not quantitative for irradiation iron samples, owing probably to hot atom or radiation effects. A detection limit of 0.002 μg is expected. (author) 10 refs.; 1 fig.; 3 tabs

  12. Determination of chemical forms of 14C in liquid discharges from nuclear power plants.

    Science.gov (United States)

    Svetlik, I; Fejgl, M; Povinec, P P; Kořínková, T; Tomášková, L; Pospíchal, J; Kurfiřt, M; Striegler, R; Kaufmanová, M

    2017-10-01

    Developments of radioanalytical methods for determination of radiocarbon in wastewaters from nuclear power plants (NPP) with pressurized light water reactors, which would distinguish between the dissolved organic and inorganic forms have been carried out. After preliminary tests, the method was used to process pilot samples from wastewater outlets from the Temelín and Dukovany NPPs (Czech Republic). The results of analysis of pilot water samples collected in 2015 indicate that the instantaneous 14 C releases into the water streams would be about 7.10 -5 (Temelín) and 4.10 -6 (Dukovany) of the total quantity of the 14 C liberated into the environment. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. Determination of Botanical Origin of Propolis from Monte Region of Argentina by Histological and Chemical Methods.

    Science.gov (United States)

    Salasa, Ana; Mercadoc, María I; Zampini, Iris C; Ponessa, Graciela I; Isla, María I

    2016-05-01

    Propolis production by honey bees is the result of a selective harvest of exudates from plants in the neighborhood of the hive. This product is used in Argentina as a food supplement and alternative medicine. The aim of this study was to determine the botanical origin of propolis from the arid regions of Monte of Argentina using rapid histochemical techniques and by comparison of TLC and HPLC-DAD chromatographic profiles with extract profiles obtained from Zuccagnia punctata, Larrea divaricata and Larrea cuneifolia, plant species that grow in the study area as a natural community named "jarillal". Microscopical analysis revealed the presence of several Z. punctata structures, such as multicellular trichomes, leaflets, stems and young leaves. Remarkable was the richness of the propolis in two bioactive chalcones, also present in Z. punctata resin; these compounds can be regarded as possible markers for propolis identification and justify its use as a dietary supplement, functional food and medicinal product. This study indicates that the source of resin used by honey bees to produce propolis in the Monte region of Argentina is only Z. punctata, a native shrub widespread in this phytogeographical region, while other more abundant species (L. divaricata and L. cuneifolia) in the region were not found, indicating that this propolis could be defined as a mono-resin, type-Zuccagnia.

  14. Determination of the number of and classification of two-component ionic-covalent chemical compounds

    International Nuclear Information System (INIS)

    Vigdorovich, V.N.; Dzhuraev, T.D.; Khanin, V.A.

    1989-01-01

    The aim of this work was to determine the number of and to classify two-component compounds corresponding to the four-electron and full-valence concepts and characterized by the ionic-covalent type of bond, on which the metallic bond is superimposed to a greater lesser degree. At the same time it was proposed to verify the position of the axes in the periodic system. The presence of numerous compound analogs for the element prototypes of one axis of the Mendeleev periodic system [the group of noble (inert) gases] was confirmed by computer experiments. However, the other axis (the carbon group) is not so obvious and is evidently due, on account of the superimposition of the effect of noncharacteristic (possible) valences, to the elements of various groups (boron, aluminum, germanium, antimony, bismuth). In addition, the compound analogs for the element prototypes of the d block are numerous, i.e., the copper-silver-gold, manganese-technetium-rhenium, and iron and platinum families

  15. Generalized molybdenum oxide surface chemical state XPS determination via informed amorphous sample model

    Energy Technology Data Exchange (ETDEWEB)

    Baltrusaitis, Jonas, E-mail: job314@lehigh.edu [Department of Chemical Engineering, Lehigh University, B336 Iacocca Hall, 111 Research Drive, Bethlehem, PA 18015 (United States); PhotoCatalytic Synthesis group, MESA+ Institute for Nanotechnology, Faculty of Science and Technology, University of Twente, Meander 229, P.O. Box 217, 7500 AE Enschede (Netherlands); Mendoza-Sanchez, Beatriz [CRANN, Chemistry School, Trinity College Dublin, Dublin (Ireland); Fernandez, Vincent [Institut des Matériaux Jean Rouxel, 2 rue de la Houssinière, BP 32229, F-44322 Nantes Cedex 3 (France); Veenstra, Rick [PhotoCatalytic Synthesis group, MESA+ Institute for Nanotechnology, Faculty of Science and Technology, University of Twente, Meander 229, P.O. Box 217, 7500 AE Enschede (Netherlands); Dukstiene, Nijole [Department of Physical and Inorganic Chemistry, Kaunas University of Technology, Radvilenu pl. 19, LT-50254 Kaunas (Lithuania); Roberts, Adam [Kratos Analytical Ltd, Trafford Wharf Road, Wharfside, Manchester, M17 1GP (United Kingdom); Fairley, Neal [Casa Software Ltd, Bay House, 5 Grosvenor Terrace, Teignmouth, Devon TQ14 8NE (United Kingdom)

    2015-01-30

    Highlights: • We analyzed and modeled spectral envelopes of complex molybdenum oxides. • Molybdenum oxide films of varying valence and crystallinity were synthesized. • MoO{sub 3} and MoO{sub 2} line shapes from experimental data were created. • Informed amorphous sample model (IASM) developed. • Amorphous molybdenum oxide XPS envelopes were interpreted. - Abstract: Accurate elemental oxidation state determination for the outer surface of a complex material is of crucial importance in many science and engineering disciplines, including chemistry, fundamental and applied surface science, catalysis, semiconductors and many others. X-ray photoelectron spectroscopy (XPS) is the primary tool used for this purpose. The spectral data obtained, however, is often very complex and can be subject to incorrect interpretation. Unlike traditional XPS spectra fitting procedures using purely synthetic spectral components, here we develop and present an XPS data processing method based on vector analysis that allows creating XPS spectral components by incorporating key information, obtained experimentally. XPS spectral data, obtained from series of molybdenum oxide samples with varying oxidation states and degree of crystallinity, were processed using this method and the corresponding oxidation states present, as well as their relative distribution was elucidated. It was shown that monitoring the evolution of the chemistry and crystal structure of a molybdenum oxide sample due to an invasive X-ray probe could be used to infer solutions to complex spectral envelopes.

  16. Synthesis, three-dimensional structure, conformation and correct chemical shift assignment determination of pharmaceutical molecules by NMR and molecular modeling

    Energy Technology Data Exchange (ETDEWEB)

    Azeredo, Sirlene O.F. de; Sales, Edijane M.; Figueroa-Villar, José D., E-mail: jdfv2009@gmail.com [Instituto Militar de Engenharia (IME), Rio de Janeiro, RJ (Brazil). Grupo de Ressonância Magnética Nuclear e Química Medicinal

    2017-07-01

    This work includes the synthesis of phenanthrenequinone guanylhydrazone and phenanthro[9,10-e][1,2,4]triazin-3-amine to be tested as intercalate with DNA for treatment of cancer. The other synthesized product, 2-[(4-chlorophenylamino)methylene]malononitrile, was designed for future determination of its activity against leishmaniasis. A common problem about some articles on the literature is that some previously published compounds display error of their molecular structures. In this article it is shown the application of several procedures of nuclear magnetic resonance (NMR) to determine the complete molecular structure and the non questionable chemical shift assignment of the synthesized compounds, and also their analysis by molecular modeling to confirm the NMR results. To determine the capacity of pharmacological compounds to interact with biological targets is determined by docking. This work is to motivate the application of NMR and molecular modeling on organic synthesis, being a process that is very important for the study of the prepared compounds as interactions with biological targets by NMR. (author)

  17. Synthesis, three-dimensional structure, conformation and correct chemical shift assignment determination of pharmaceutical molecules by NMR and molecular modeling

    International Nuclear Information System (INIS)

    Azeredo, Sirlene O.F. de; Sales, Edijane M.; Figueroa-Villar, José D.

    2017-01-01

    This work includes the synthesis of phenanthrenequinone guanylhydrazone and phenanthro[9,10-e][1,2,4]triazin-3-amine to be tested as intercalate with DNA for treatment of cancer. The other synthesized product, 2-[(4-chlorophenylamino)methylene]malononitrile, was designed for future determination of its activity against leishmaniasis. A common problem about some articles on the literature is that some previously published compounds display error of their molecular structures. In this article it is shown the application of several procedures of nuclear magnetic resonance (NMR) to determine the complete molecular structure and the non questionable chemical shift assignment of the synthesized compounds, and also their analysis by molecular modeling to confirm the NMR results. To determine the capacity of pharmacological compounds to interact with biological targets is determined by docking. This work is to motivate the application of NMR and molecular modeling on organic synthesis, being a process that is very important for the study of the prepared compounds as interactions with biological targets by NMR. (author)

  18. Determination of Hot Springs Physico-Chemical Water Quality Potentially Use for Balneotherapy

    International Nuclear Information System (INIS)

    Zaini Hamzah; Nurul Latiffah Abd Rani; Ahmad Saat; Ab Khalik Wood

    2013-01-01

    Hot springs areas are attractive places for locals and foreigners either for excursion or for medical purposes such as for healing of various types of diseases. This is because the hot spring water is believed rich in salt, sulfur, and sulfate in the water body. For many thousands of years, people have used hot springs water both for cozy bathing and therapy. Balneotherapy is the term used where the patients were immersed in hot mineral water baths emerged as an important treatment in Europe around 1800s. In view of this fact, a study of hot springs water was performed with the objective to determine the concentration of Na + , K + , Ca 2+ , S, SO 4 2- and Cl - in hot springs water around the State of Selangor, Malaysia. Energy dispersive X-ray Fluorescent Spectrometry (EDXRF) was used to measure the concentrations of Na + , K + , Ca 2+ and S meanwhile for SO 4 2- and Cl - anion, Ion Chromatography (IC) was used. The concentration of Na + obtained for filtered and unfiltered samples ranged from 33.68 to 80.95 and 37.03 to 81.91 ppm respectively. Meanwhile, the corresponding concentrations of K + ranged from 1.47 to 45.72 and 1.70 to 56.81 ppm. Concentrations of Ca 2+ ranged from 2.44 to 18.45 and 3.75 to 19.77 ppm. The concentration of S obtained for filtered and unfiltered samples ranged from 1.87 to 12.41 and 6.25 to 12.86 ppm. The concentrations for SO 4 2- and Cl - obtained ranged from 0.15 to 1.51 ppm and 7.06 to 20.66 ppm for filtered samples. The data signified higher concentration of salt and other important nutrients in hot spring water. (author)

  19. Determining the chemical exchange saturation transfer (CEST) behavior of citrate and spermine under in vivo conditions

    Science.gov (United States)

    Basharat, Meer; deSouza, Nandita M.; Parkes, Harold G.

    2015-01-01

    Purpose To estimate the exchange rates of labile 1H in citrate and spermine, metabolites present in prostatic secretions, to predict the size of the citrate and spermine CEST effects in vivo. Methods CEST z‐spectra were acquired at high‐field [11.7 Tesla (T)] from citrate and spermine solutions at physiological pH (6.5) using saturation power 6 μT. CEST was performed at different temperatures to determine exchange regimes (slow, intermediate or fast). For low pH solutions of spermine, exchange rates were estimated from resonance line width, fitting z‐spectra using the Bloch equations incorporating exchange, and using quantifying exchange using saturation time experiments (QUEST). These rates were extrapolated to physiological pH. Results Citrate showed little CEST effect at pH 6.5 and temperature (T) = 310 K (maximum 0.001% mM‐1), indicating fast exchange, whereas spermine showed greater CEST effects (maximum 0.2% mM‐1) indicating intermediate‐to‐fast exchange. Extrapolating data acquired from low pH spermine solutions predicts exchange rates at pH 6.5 and T of 310 K of at least 2 × 104s‐1. Conclusion Citrate and spermine show minimal CEST effects at 11.7T even using high saturation power. These effects would be much less than 2% at clinical field‐strengths due to relatively faster exchange and would be masked by CEST from proteins. Magn Reson Med 76:742–746, 2016. © 2015 The Authors. Magnetic Resonance in Medicine published by Wiley Periodicals, Inc. on behalf of International Society for Magnetic Resonance in Medicine. This is an open access article under the terms of the Creative Commons Attribution License, which permits use, distribution and reproduction in any medium, provided the original work is properly cited. PMID:26467055

  20. A single sex pheromone receptor determines chemical response specificity of sexual behavior in the silkmoth Bombyx mori.

    Science.gov (United States)

    Sakurai, Takeshi; Mitsuno, Hidefumi; Haupt, Stephan Shuichi; Uchino, Keiro; Yokohari, Fumio; Nishioka, Takaaki; Kobayashi, Isao; Sezutsu, Hideki; Tamura, Toshiki; Kanzaki, Ryohei

    2011-06-01

    In insects and other animals, intraspecific communication between individuals of the opposite sex is mediated in part by chemical signals called sex pheromones. In most moth species, male moths rely heavily on species-specific sex pheromones emitted by female moths to identify and orient towards an appropriate mating partner among a large number of sympatric insect species. The silkmoth, Bombyx mori, utilizes the simplest possible pheromone system, in which a single pheromone component, (E, Z)-10,12-hexadecadienol (bombykol), is sufficient to elicit full sexual behavior. We have previously shown that the sex pheromone receptor BmOR1 mediates specific detection of bombykol in the antennae of male silkmoths. However, it is unclear whether the sex pheromone receptor is the minimally sufficient determination factor that triggers initiation of orientation behavior towards a potential mate. Using transgenic silkmoths expressing the sex pheromone receptor PxOR1 of the diamondback moth Plutella xylostella in BmOR1-expressing neurons, we show that the selectivity of the sex pheromone receptor determines the chemical response specificity of sexual behavior in the silkmoth. Bombykol receptor neurons expressing PxOR1 responded to its specific ligand, (Z)-11-hexadecenal (Z11-16:Ald), in a dose-dependent manner. Male moths expressing PxOR1 exhibited typical pheromone orientation behavior and copulation attempts in response to Z11-16:Ald and to females of P. xylostella. Transformation of the bombykol receptor neurons had no effect on their projections in the antennal lobe. These results indicate that activation of bombykol receptor neurons alone is sufficient to trigger full sexual behavior. Thus, a single gene defines behavioral selectivity in sex pheromone communication in the silkmoth. Our findings show that a single molecular determinant can not only function as a modulator of behavior but also as an all-or-nothing initiator of a complex species-specific behavioral sequence.

  1. A single sex pheromone receptor determines chemical response specificity of sexual behavior in the silkmoth Bombyx mori.

    Directory of Open Access Journals (Sweden)

    Takeshi Sakurai

    2011-06-01

    Full Text Available In insects and other animals, intraspecific communication between individuals of the opposite sex is mediated in part by chemical signals called sex pheromones. In most moth species, male moths rely heavily on species-specific sex pheromones emitted by female moths to identify and orient towards an appropriate mating partner among a large number of sympatric insect species. The silkmoth, Bombyx mori, utilizes the simplest possible pheromone system, in which a single pheromone component, (E, Z-10,12-hexadecadienol (bombykol, is sufficient to elicit full sexual behavior. We have previously shown that the sex pheromone receptor BmOR1 mediates specific detection of bombykol in the antennae of male silkmoths. However, it is unclear whether the sex pheromone receptor is the minimally sufficient determination factor that triggers initiation of orientation behavior towards a potential mate. Using transgenic silkmoths expressing the sex pheromone receptor PxOR1 of the diamondback moth Plutella xylostella in BmOR1-expressing neurons, we show that the selectivity of the sex pheromone receptor determines the chemical response specificity of sexual behavior in the silkmoth. Bombykol receptor neurons expressing PxOR1 responded to its specific ligand, (Z-11-hexadecenal (Z11-16:Ald, in a dose-dependent manner. Male moths expressing PxOR1 exhibited typical pheromone orientation behavior and copulation attempts in response to Z11-16:Ald and to females of P. xylostella. Transformation of the bombykol receptor neurons had no effect on their projections in the antennal lobe. These results indicate that activation of bombykol receptor neurons alone is sufficient to trigger full sexual behavior. Thus, a single gene defines behavioral selectivity in sex pheromone communication in the silkmoth. Our findings show that a single molecular determinant can not only function as a modulator of behavior but also as an all-or-nothing initiator of a complex species

  2. A study on chemical element determinations in human nails by neutron activation analysis

    International Nuclear Information System (INIS)

    Sanches, Thalita Pinheiro; Saiki, Mitiko

    2013-01-01

    Nail analyses have been the object of study in order to assess the levels of elements accumulated in the human organism and to use this tissue to monitor environmental and occupational exposure, to evaluate the nutritional status, to verify intoxication by toxic metals and to diagnose or to prevent diseases. Nail analyses present advantages due to easy sample collection, storage, transportation and this tissue provides element level accumulation over time. However, there is controversy regarding the application of nail analysis data due to difficulties to establish reliable reference values or element concentration ranges as control values. The objective of this study was to evaluate the factors that can affect nail element concentrations for further sample analyses of a group of individuals by applying neutron activation analysis (NAA). Fingernails and toenails collected from adult individuals of both genders, aged 18 to 71 years, living in the Sao Paulo Metropolitan Region were cut in small fragments, cleaned and dried for analyses. Samples and element standards were irradiated for 16 h under a thermal neutron flux of about 4.5 x 10 12 n cm -2 s -1 at the IEA-R1 nuclear research reactor followed by gamma ray spectrometry. Element concentrations for As, Br, Ca, Co, Cr, Cs, Fe, K, La, Na, Rb, Sb, Sc, Se and Zn were determined. For quality control of the analytical results, certified reference materials were analysed and the results showed good accuracy and precision with relative errors and relative standard deviations lower than 5.1 % and 11.6 %, respectively. Preliminary assays indicated that the contribution due to impurities from plastic involucres used in the irradiation as well as those from nail polishes is very low and could be considered negligible. Results from the nail sample cleaning process using distinct procedures indicated that HNO 3 solution may cause sample dissolution. Sample homogeneity was verified by analysis of a sample in replicate. A

  3. A study on chemical element determinations in human nails by neutron activation analysis

    International Nuclear Information System (INIS)

    Sanches, Thalita Pinheiro

    2012-01-01

    Nail analyses have been the object of study in order to assess the levels of elements accumulated in the human organism and to use this tissue to monitor environmental and occupational exposure, to evaluate the nutritional status, to verify intoxication by toxic metals and to diagnose or to prevent diseases. Nail analyses present advantages due to easy sample collection, storage, transportation and this tissue provides element level accumulation over time. However, there is controversy regarding the application of nail analysis data due to difficulties to establish reliable reference values or element concentration ranges as control values. The objective of this study was to evaluate the factors that can affect nail element concentrations for further sample analyses of a group of individuals by applying neutron activation analysis (NAA). Fingernails and toenails collected from adult individuals of both genders, aged 18 to 71 years, living in the Sao Paulo Metropolitan Region were cut in small fragments, cleaned and dried for analyses. Samples and element standards were irradiated for 16 h under a thermal neutron flux of about 4.5 x 10 12 n cm -2 s -1 at the IEA-R1 nuclear research reactor followed by gamma ray spectrometry. Element concentrations for As, Br, Ca, Co, Cr, Cs, Fe, K, La, Na, Rb, Sb, Sc, Se and Zn were determined. For quality control of the analytical results, certified reference materials were analysed and the results showed good accuracy and precision with relative errors and relative standard deviations lower than 5.1 % and 11.6 %, respectively. Preliminary assays indicated that the contribution due to impurities from plastic involucres used in the irradiation as well as those from nail polishes is very low and could be considered negligible. Results from the nail sample cleaning process using distinct procedures indicated that HNO 3 solution may cause sample dissolution. Sample homogeneity was verified by analysis of a sample in replicate. A

  4. A study on chemical element determinations in human nails by neutron activation analysis

    Energy Technology Data Exchange (ETDEWEB)

    Sanches, Thalita Pinheiro; Saiki, Mitiko, E-mail: thalitapsanches@usp.br, E-mail: mitiko@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2013-07-01

    Nail analyses have been the object of study in order to assess the levels of elements accumulated in the human organism and to use this tissue to monitor environmental and occupational exposure, to evaluate the nutritional status, to verify intoxication by toxic metals and to diagnose or to prevent diseases. Nail analyses present advantages due to easy sample collection, storage, transportation and this tissue provides element level accumulation over time. However, there is controversy regarding the application of nail analysis data due to difficulties to establish reliable reference values or element concentration ranges as control values. The objective of this study was to evaluate the factors that can affect nail element concentrations for further sample analyses of a group of individuals by applying neutron activation analysis (NAA). Fingernails and toenails collected from adult individuals of both genders, aged 18 to 71 years, living in the Sao Paulo Metropolitan Region were cut in small fragments, cleaned and dried for analyses. Samples and element standards were irradiated for 16 h under a thermal neutron flux of about 4.5 x 10{sup 12} n cm{sup -2} s{sup -1} at the IEA-R1 nuclear research reactor followed by gamma ray spectrometry. Element concentrations for As, Br, Ca, Co, Cr, Cs, Fe, K, La, Na, Rb, Sb, Sc, Se and Zn were determined. For quality control of the analytical results, certified reference materials were analysed and the results showed good accuracy and precision with relative errors and relative standard deviations lower than 5.1 % and 11.6 %, respectively. Preliminary assays indicated that the contribution due to impurities from plastic involucres used in the irradiation as well as those from nail polishes is very low and could be considered negligible. Results from the nail sample cleaning process using distinct procedures indicated that HNO{sub 3} solution may cause sample dissolution. Sample homogeneity was verified by analysis of a sample in

  5. Matéria seca de plantas de cobertura, produção de cebola e atributos químicos do solo em sistema plantio direto agroecológico Dry matter of cover crops, onion yield and soil chemical attributes in agroecological no-tillage system

    Directory of Open Access Journals (Sweden)

    Monique Souza

    2013-01-01

    treatments was implanted in April: weed vegetation (T1, Hordeum vulgare L. (2010/Avena strigosa L. (2011 (T2, Secale cereale L. (T3, Raphanus sativus L. (T4, Secale cereale L + Raphanus sativus L. (T5 e Hordeum vulgare L. (2010/Avena strigosa L. (2011 + Raphanus sativus L. (T6. At 60, 80 and 95 days after sowing (DAS of winter species, the cover crops were collected to determine the dry matter yield. In July the onion seedlings were transplanted and in November the yield was evaluated. After the rolling of winter cover crops and after onion harvest, soil was collected at 0-10cm for the evaluation of chemical attributes. The cultivation and deposition of waste from cover crops in no-tillage contributed to the growth and maintenance of the total production of onion over the years. The soil chemical attributes in 0-10cm layer, with the exception of exchangeable K, available P and CTCpH7,0 saturation values for bases, were not affected by cover crops cultivation and deposition of waste.

  6. Complete determination of neutron yield from 62 MeV protons on 9Be for the design of a low – power ADS

    Directory of Open Access Journals (Sweden)

    Schillaci Maria

    2014-03-01

    Full Text Available Within the European Partitioning & Transmutation research programs, infrastructures specifically dedicated to the study of fundamental reactor physics of future fast neutron-based reactors are very important. In this respect, an Accelerator Driven System low-power prototype, based on a 70 MeV proton beam impinging on a thick Beryllium converter, was recently proposed and designed within the INFN-E project. The world data on neutron yield from Be target are scarce in this proton energy range. This lack of data calls for a dedicated measurement which was performed at INFN Laboratori Nazionali del Sud, covering a wide angular range, from 0 to 150 degrees, and an almost complete neutron energy interval, from thermal up to the beam energy. In this contribution the results are discussed together with the description of the proposed ADS facility.

  7. Determination of the {tau}-lepton reconstruction and identification efficiency using Z {yields} {tau}{tau} events in first data at ATLAS

    Energy Technology Data Exchange (ETDEWEB)

    Fischer, Gordon

    2011-10-15

    The Large Hadron Collider (LHC) at CERN started operation in November 2009. At the same time the ATLAS experiment started data taking. Since this time a large number of Z-bosons is produced. An important decay channel of the Z-boson is the decay into two {tau} -leptons. The large mass of the {tau}-lepton allows the decay into pions or kaons. In many models considering new physics the {tau}-lepton is an important final state. The LHC is a proton-proton collider and for that reason, the hadronic {tau}-lepton decay is difficult to distinguish from QCD multi-jet background. For the selection of hadronically decaying {tau}-leptons, reconstruction and identification algorithms were developed in order to suppress this background. In order to measure the Z-boson production cross section or possible new particles decaying into {tau}-leptons, the estimation of the {tau}-lepton reconstruction and identification efficiency is required. Furthermore, for detector calibration the Z-boson as well as the {tau}-lepton are helpful probes. In this thesis two methods are discussed which provide an estimation of {tau}-lepton reconstruction and identification efficiencies from data. The full selection of Z {yields} {tau}{tau} events including data-driven techniques for background extraction is discussed. The semi-leptonic Z {yields} {tau}{tau} channel promises a good QCD multi-jet suppression because of the selected additional lepton. For that reason also the leptonically decaying {tau}-lepton is discussed. The Z-boson production cross section can be calculated with the estimated efficiencies. (orig.)

  8. Method for determining the optimum mode of operation of the chemical water regime in the water-steam-circuit of power plants

    International Nuclear Information System (INIS)

    Sommerfeldt, P.; Reisner, H.; Hartmann, G.; Kulicke, P.

    1988-01-01

    The method aims at increasing the lifetime of secondary coolant circuit components in nuclear power plants through the determination of the optimum mode of operation of the chemical water regime by help of radioisotopes

  9. Melhorias nas propriedades químicas de um solo salino-sódico e rendimento de arroz, sob diferentes tratamentos Improvement in chemical properties of saline-sodic soil and rice yield under under different treatments

    Directory of Open Access Journals (Sweden)

    Everaldo Mariano Gomes

    2000-12-01

    Full Text Available Instalou-se um experimento num solo salino-sódico no Perímetro Irrigado de São Gonçalo, com o objetivo de se avaliar o efeito de diferentes produtos condicionadores nas propriedades químicas do solo e seus reflexos nos componentes de produção e rendimento de grãos na cultura de arroz irrigado (Oryza sativa L.. O delineamento experimental foi inteiramente casualizado, com cinco tratamentos e cinco repetições. Os tratamentos estudados foram: gesso (20 Mg ha-1; casca de arroz (15 Mg ha-1; testemunha; vinhaça (40 m³ ha-1 e esterco de curral (40 Mg ha-1. Após aplicação dos tratamentos, o solo foi lixiviado durante 40 dias, mantendo uma lâmina de 8 cm de água nas parcelas. Os tratamentos mostraram efeitos positivos nas propriedades químicas do solo (percentagem de sódio trocável, condutividade elétrica do extrato de saturação e pH da pasta saturada sendo que o esterco de curral e gesso proporcionaram apreciáveis decréscimos em comparação aos outros tratamentos; entretanto, os produtos utilizados não mostraram efeitos significativos no número de panículas, peso de panículas e rendimento do arroz.An experiment was installed in a saline-sodic soil of the Irrigated Perimeter of São Gonçalo, with the objective of evaluating the effect of different amendments in the chemical properties of soil and its posterior reflexes in the components of production and grain yield of irrigated rice (Oryza sativa L.. The experiment consisted of five treatments with five replications in a completely randomized design. The treatments studied were: gypsum (20 Mg ha-1; rice husk (15 Mg ha-1; control; stillage (40 m³ ha-1 and farmyard manure (40 Mg ha-1. After incorporation of amendments, the soil was leached for 40 days, keeping an 8 cm depth of water in the plots. The treatments showed positive effects in the chemical properties of the soil (exchangeable sodium percentage, electrical conductivity of saturation extract and pH of saturation

  10. Development, implementation and validation of a practice-orientated method for the determination of yields of biogas or methane, respectively; Entwicklung, Implementierung und Validierung eines praxisnahen Verfahrens zur Bestimmung von Biogas- bzw. Methanertraegen

    Energy Technology Data Exchange (ETDEWEB)

    Fritz, Thomas

    2008-12-15

    The increasing number of the world population results in a pronounced ascent of the world-wide energy consumption. This problem additionally is strengthened by the release of carbon dioxide. In the contribution under consideration, the author develops a method with which the yields of fermentation gas or methane, respectively, reliably as well as practice-orientated can be determined. Different influences on the determination of these yields are described. Thus, the investigations in this area are to be standardised further. The comparability under laboratories is to be increased. (orig.) [German] Die steigende Zahl der Weltbevoelkerung fuehrt zu einem Ausgepraegten Anstieg des weltweiten Energieverbrauchs. Diese Problematik wird durch die Freisetzung von Kohlendioxid zusaetzlich verstaerkt. Im vorliegenden Beitrag entwickelt der Autor eine Methode, mit der die Ertraege von Biogas beziehungsweise Methan zuverlaesslich und praxisnah bestimmt werden koennen. Es werden verschiedene Einfluesse auf die Bestimmung dieser Ertraege dargestellt. Damit sollen die Untersuchungen auf diesem Gebiet weiter standardisiert und die Vergleichbarkeit unter Laboren erhoeht werden.

  11. Factors determining the concentration and chemical composition of particulate matter in the air of selected service facilities

    Science.gov (United States)

    Rogula-Kopiec, Patrycja; Pastuszka, Józef; Mathews, Barbara; Widziewicz, Kamila

    2018-01-01

    The link between increased morbidity and mortality and increasing concentrations of particulate matter (PM) resulted in great attention being paid to the presence and physicochemical properties of PM in closed rooms, where people spends most of their time. The least recognized group of such indoor environments are small service facilities. The aim of this study was to identify factors which determine the concentration, chemical composition and sources of PM in the air of different service facilities: restaurant kitchen, printing office and beauty salon. The average PM concentration measured in the kitchen was 5-fold (PM4, particle fraction ≥ 4 μm) and 5.3-fold (TSP, total PM) greater than the average concentration of these PM fractions over the same period. During the same measurement period in the printing office and in the beauty salon, the mean PM concentration was 10- and 4-fold (PM4) and 8- and 3-fold (TSP) respectively greater than the mean concentration of these PM fractions in outdoor air. In both facilities the main source of PM macro-components, especially organic carbon, were chemicals, which are normally used in such places - solvents, varnishes, paints, etc. The influence of some metals inflow from the outdoor air into indoor environment of those facilities was also recognized.

  12. Determinants of the Sensory Quality of Półgęsek in Relation to Volatile Compounds and Chemical Composition

    Directory of Open Access Journals (Sweden)

    Nowicka Katarzyna

    2017-12-01

    Full Text Available The objective of this study was to determine the sensory quality of a specific Polish traditional product made from cured and then smoked goose meat (półgęsek in relation to its volatile compounds and chemical composition. In general, the examined samples contained 66.2% water, 12.2% fat, 17.9% protein, 1.8% connective tissue, and 2.3% NaCl. Moreover, 47 volatile compounds were identified and quantified. The typical decomposition products derived from lipid oxidation, amino acid degradation, carbohydrate fermentation and microbial esterification were the main volatiles detected in all the samples. The volatiles generated by the smoking process and the ones originating from spices were also observed. The results of the sensory evaluation indicated that all the samples of the analyzed products were characterized by a high overall quality. Results of the Principal Component Analysis (PCA showed, however, that specific groups of products have their own unique sensory profile. Additionally, the sensory analysis confirmed the significant role of the chemical composition and volatile compounds in the development of the overall quality of półgęsek.

  13. Determination of chemical activities of Fe, Cr, Ni and Mn in stainless steel 316 by Knudsen effusion cell mass spectrometry

    International Nuclear Information System (INIS)

    Venugopal, V.; Kulkarni, S.G.; Subbanna, C.S.; Sood, D.D.

    1995-01-01

    Cold-worked austenitic stainless steel of the type AISI 316 is being used as the cladding and wrapper materials in fast reactor fuel pins. Knowledge of the thermodynamic activities of the steel constituents is necessary to predict the possibility of fuel-cladding, coolant-cladding or fission product-cladding chemical reactions. The thermodynamic activities of Fe, Cr, Ni and Mn for stainless steel 316 were determined by measuring their partial pressures in the temperature range 1293-2120 K, using Knudsen effusion cell mass spectrometry. High purity Ag was used as an internal calibrant. The chemical activities of Fe (a Fe ), Cr (a Cr ), Ni (a Ni ) and Mn (a Mn ) were evaluated using literature data for the vapour pressures of pure metals. log a Fe ±0.18=-1.586+2074/T (T=1293-1872 K)log a Cr ±0.30=-2.350+2612/T (T=1293-2120 K)log a Ni ±0.20=-2.140+1794/T (T=1468-1974 K)log a Mn ±0.23=-2.041-5478/T (T=1302-1894 K) ((orig.))

  14. Quantitative anomalous small-angle X-ray scattering - The determination of chemical concentrations in nano-scale phases

    International Nuclear Information System (INIS)

    Goerigk, G.; Huber, K.; Mattern, N.; Williamson, D.L.

    2012-01-01

    In the last years Anomalous Small-Angle X-ray Scattering became a precise quantitative method resolving scattering contributions two or three orders of magnitude smaller compared to the overall small-angle scattering, which are related to the so-called pure-resonant scattering contribution. Additionally to the structural information precise quantitative information about the different constituents of multi-component systems like the fraction of a chemical component implemented into the materials nano-structures are obtained from these scattering contributions. The application of the Gauss elimination algorithm to the vector equation established by ASAXS measurements at three X-ray energies is demonstrated for three examples from chemistry and solid state physics. All examples deal with the quantitative analysis of the Resonant Invariant (RI-analysis). From the integrals of the pure-resonant scattering contribution the chemical concentrations in nano-scaled phases are determined. In one example the correlated analysis of the Resonant Invariant and the Non-resonant Invariant (NI-analysis) is employed. (authors)

  15. Method for accurate determination of dissociation constants of optical ratiometric systems: chemical probes, genetically encoded sensors, and interacting molecules.

    Science.gov (United States)

    Pomorski, Adam; Kochańczyk, Tomasz; Miłoch, Anna; Krężel, Artur

    2013-12-03

    Ratiometric chemical probes and genetically encoded sensors are of high interest for both analytical chemists and molecular biologists. Their high sensitivity toward the target ligand and ability to obtain quantitative results without a known sensor concentration have made them a very useful tool in both in vitro and in vivo assays. Although ratiometric sensors are widely used in many applications, their successful and accurate usage depends on how they are characterized in terms of sensing target molecules. The most important feature of probes and sensors besides their optical parameters is an affinity constant toward analyzed molecules. The literature shows that different analytical approaches are used to determine the stability constants, with the ratio approach being most popular. However, oversimplification and lack of attention to detail results in inaccurate determination of stability constants, which in turn affects the results obtained using these sensors. Here, we present a new method where ratio signal is calibrated for borderline values of intensities of both wavelengths, instead of borderline ratio values that generate errors in many studies. At the same time, the equation takes into account the cooperativity factor or fluorescence artifacts and therefore can be used to characterize systems with various stoichiometries and experimental conditions. Accurate determination of stability constants is demonstrated utilizing four known optical ratiometric probes and sensors, together with a discussion regarding other, currently used methods.

  16. Proficiency Testing for Determination of Water Content in Toluene of Chemical Reagents by iteration robust statistic technique

    Science.gov (United States)

    Wang, Hao; Wang, Qunwei; He, Ming

    2018-05-01

    In order to investigate and improve the level of detection technology of water content in liquid chemical reagents of domestic laboratories, proficiency testing provider PT0031 (CNAS) has organized proficiency testing program of water content in toluene, 48 laboratories from 18 provinces/cities/municipals took part in the PT. This paper introduces the implementation process of proficiency testing for determination of water content in toluene, including sample preparation, homogeneity and stability test, the results of statistics of iteration robust statistic technique and analysis, summarized and analyzed those of the different test standards which are widely used in the laboratories, put forward the technological suggestions for the improvement of the test quality of water content. Satisfactory results were obtained by 43 laboratories, amounting to 89.6% of the total participating laboratories.

  17. Radiochemical studies in chemical separation and spectrographic determination of rare earths in thorium oxide matrix (Preprint No. RA.06)

    International Nuclear Information System (INIS)

    Adya, V.C.; Dhawale, B.A.; Rajeshwari, B.; Bangia, T.R.; Sastry, M.D.

    1989-01-01

    A chemical separation procedure was standardised for the separation of traces of rare earths from ThO 2 matrix using HDEHP (Di 2-ethyl hexyl phosphoric acid). The studies were carried out using both nitric acid and hydrochloric acid medium in different concentrations. The extraction studies were also carried out using radioactive isotopes of rare earths viz. 141 Ce, 152-154 Eu, 153 Gd, 170 Tm etc. The extraction was effective in both media. In 0.1 M HDEHP/xylene and 3 M HNO 3 , Ce was partially extracted into organic phase. So HCl/xylene medium was chosen for extraction purposes. The recovery was confirmed by both gamma counting and emission spectropgraphic method. It was found to be quantitative within experimental error. The separation procedure development here was used for determination of rare earths in thorium oxide matrix by emission spectrographic method. (author)

  18. Quaternary structure of the ATPase complex of human 26S proteasomes determined by chemical cross-linking

    DEFF Research Database (Denmark)

    Hartmann-Petersen, R; Tanaka, K; Hendil, K B

    2001-01-01

    and substrate specificity. Among the approximately 18 subunits of PA700 regulator, six are ATPases. The ATPases presumably recognize, unfold, and translocate substrates into the interior of the 26S proteasome. It is generally believed that the ATPases form a hexameric ring. By means of chemical cross......-linking, immunoprecipitation, and blotting, we have determined that the ATPases are organized in the order S6-S6'-S10b-S8-S4-S7. Additionally, we found cross-links between the ATPase S10b and the 20S proteasome subunit alpha6. Together with the previously known interaction between S8 and alpha1 and between S4 and alpha7......, these data establish the relative orientations of ATPases with respect to the 20S proteasome....

  19. Noninvasive Biomonitoring Approaches to Determine Dosimetry and Risk Following Acute Chemical Exposure: Analysis of Lead or Organophosphate Insecticide in Saliva

    International Nuclear Information System (INIS)

    Timchalk, Chuck; Poet, Torka S.; Kousba, Ahmed A.; Campbell, James A.; Lin, Yuehe

    2004-01-01

    There is a need to develop approaches for assessing risk associated with acute exposures t