WorldWideScience

Sample records for chemical industry waste

  1. Chemical Industry Waste water Treatment

    International Nuclear Information System (INIS)

    Nasr, F.A.; Doma, H.S.; El-Shafai, S.A.; Abdel-HaJim, H.S.

    2004-01-01

    Treatment of chemical industrial wastewater from building and construction chemicals factory and plastic shoes manufacturing factory was investigated. The two factories discharge their wastewater into the public sewerage network. The results showed the wastewater discharged from the building and construction chemicals factory was highly contaminated with organic compounds. The average values of COD and BOD were 2912 and 150 mg O 2 /l. Phenol concentration up to 0.3 mg/l was detected. Chemical treatment using lime aided with ferric chloride proved to be effective and produced an effluent characteristics in compliance with Egyptian permissible limits. With respect to the other factory, industrial wastewater was mixed with domestic wastewater in order to lower the organic load. The COD, BOD values after mixing reached 5239 and 2615 mg O 2 /l. The average concentration of phenol was 0.5 mg/l. Biological treatment using activated sludge or rotating biological contactor (RBe) proved to be an effective treatment system in terms of producing an effluent characteristic within the permissible limits set by the law

  2. Olefin Recovery from Chemical Industry Waste Streams

    Energy Technology Data Exchange (ETDEWEB)

    A.R. Da Costa; R. Daniels; A. Jariwala; Z. He; A. Morisato; I. Pinnau; J.G. Wijmans

    2003-11-21

    The objective of this project was to develop a membrane process to separate olefins from paraffins in waste gas streams as an alternative to flaring or distillation. Flaring these streams wastes their chemical feedstock value; distillation is energy and capital cost intensive, particularly for small waste streams.

  3. Chemical analysis for waste management in paint industries

    International Nuclear Information System (INIS)

    Nawaz, Z.; Naveed, S.; Shiekh, N.A.; Sagheer, K.

    2005-01-01

    The chemical analysis of paint industries waste has been carried out; the main emission sources are the heating of raw materials and lacquer. Also the waste from other applications and production contains high concentration of heavy metals, VOC's, COD, TDS with notable acidity and alkalinity. Based on the analysis it was observed that the major losses of production could be minimized. Further toxic effects of the waste material can be minimized. In this reference measures to minimize production losses should be adopted along with the proper management. These laboratory results also lead to the areas of emissions and waste production during manufacturing process. Solutions have been proposed for process development and integrated waste minimization. (author)

  4. Strategy of Construction and Demolition Waste Management after Chemical Industry Facilities Removal

    Science.gov (United States)

    Tashkinova, I. N.; Batrakova, G. M.; Vaisman, Ya I.

    2017-06-01

    Mixed waste products are generated in the process of irrelevant industrial projects’ removal if conventional techniques of their demolition and dismantling are applied. In Russia the number of unused chemical industry facilities including structures with high rate of wear is growing. In removing industrial buildings and production shops it is used conventional techniques of demolition and dismantling in the process of which mixed waste products are generated. The presence of hazardous chemicals in these wastes makes difficulties for their use and leads to the increasing volume of unutilized residues. In the process of chemical industry facilities’ removal this fact takes on special significance as a high level of hazardous chemicals in the waste composition demands for the realization of unprofitable measures aimed at ensuring environmental and industrial safety. The proposed strategy of managing waste originated from the demolition and dismantling of chemical industry facilities is based on the methodology of industrial metabolism which allows identifying separate material flows of recycled, harmful and ballast components, performing separate collection of components during removal and taking necessary preventive measures. This strategy has been tested on the aniline synthesis plant being in the process of removal. As a result, a flow of 10 wt. %, subjected to decontamination, was isolated from the total volume of construction and demolition waste (C&D waste). The considered approach allowed using the resource potential of more than 80wt. % of waste and minimizing the disposed waste volume.

  5. Industrial Waste

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund

    2011-01-01

    generation rates and material composition as well as determining factors are discussed in this chapter. Characterizing industrial waste is faced with the problem that often only a part of the waste is handled in the municipal waste system, where information is easily accessible. In addition part...... of the industrial waste may in periods, depending on market opportunities and prices, be traded as secondary rawmaterials. Production-specificwaste from primary production, for example steel slag, is not included in the current presentation. In some countries industries must be approved or licensed and as part...... of the system industry has to inform at the planning stage and afterwards in yearly reports on their waste arising and how the waste is managed. If available such information is very helpful in obtaining information about that specific industry. However, in many countries there is very little information...

  6. Chemical studies on some radionuclides in industrial wastes

    International Nuclear Information System (INIS)

    Ibrahim, M.F.A.

    2006-01-01

    in this thesis, there is much concern about the technologically enhanced-naturally occurring radioactive materials (TE-NORM) associated with phosphate fertilizers and chemical materials production in abu Zaabal Company, Egypt. the phosphogypsum (PG)wastes associated with the phosporic acid produced was found to contain high concentrations of radioactivity than that exists naturally (i.e., background). this chapter includes sufficient information about the different sources of the environmental radioactivities as well as TE-NORM associated with phosphate fertilizers and oil and gas production facilities . it includes also, information about the history, methods used in detection and measurements, limits, trials of TE-NORM treatment . it contains some aspects on the chemistry and radiochemistry of radium and radon. also, this chapter includes the aim of the present work.this chapter includes preparation of all required samples for analysis, as well as chemicals and reagents used in the experimental work .it includes also, description of the different spectroscopic instruments used. which are: HPGe γ-ray spectrometry,α-spectrometry, X-ray diffraction(XRD), x-ray fluorescence (XRF), and IR-spectrometry. the energy and efficiency calibrations of both γ and α-spectrometry are also presented

  7. Bioelectrochemical Integration of Waste Heat Recovery, Waste-to- Energy Conversion, and Waste-to-Chemical Conversion with Industrial Gas and Chemical Manufacturing Processes

    Energy Technology Data Exchange (ETDEWEB)

    Mac Dougall, James [Air Products and Chemicals, Inc., Allentown, PA (United States)

    2016-02-05

    Many U.S. manufacturing facilities generate unrecovered, low-grade waste heat, and also generate or are located near organic-content waste effluents. Bioelectrochemical systems, such as microbial fuel cells and microbial electrolysis cells, provide a means to convert organic-content effluents into electric power and useful chemical products. A novel biochemical electrical system for industrial manufacturing processes uniquely integrates both waste heat recovery and waste effluent conversion, thereby significantly reducing manufacturing energy requirements. This project will enable the further development of this technology so that it can be applied across a wide variety of US manufacturing segments, including the chemical, food, pharmaceutical, refinery, and pulp and paper industries. It is conservatively estimated that adoption of this technology could provide nearly 40 TBtu/yr of energy, or more than 1% of the U.S. total industrial electricity use, while reducing CO2 emissions by more than 6 million tons per year. Commercialization of this technology will make a significant contribution to DOE’s Industrial Technology Program goals for doubling energy efficiency and providing a more robust and competitive domestic manufacturing base.

  8. Review on Chemical treatment of Industrial Waste Water * OPSAHU

    African Journals Online (AJOL)

    MICHAEL HORSFALL

    water is used and lot of wastewater generated from industries due their processes and washing purpose. A large ..... for coagulation–precipitation of cosmetic wastewater industry (Aloui ..... Gregor, J.E., Nokes, C.J., Fenton, E., 1997. Optimising ...

  9. Physico-chemical and toxicological assessment of liquid wastes from olive processing-related industries.

    Science.gov (United States)

    Pierantozzi, Pierluigi; Zampini, Catiana; Torres, Mariela; Isla, María I; Verdenelli, Romina A; Meriles, José M; Maestri, Damián

    2012-01-30

    In the last few years, agricultural uses of waste waters from olive processing-related industries have been gaining interest mainly with a view to composting or bio-fertilizers. The present work examines physico-chemical, toxicological and geno-toxicological properties of three liquid wastes, namely olive mill wastewater (OMWW), olive wet husk and olive brine. The effect of OMWW spreading on soil microbial activity and biomass was also evaluated. Data from Artemia salina and Lactuca sativa toxicity tests indicated high levels of lethality, and inhibitory effects on seed germination and seedling growth of all olive wastes. The genotoxicity assays using Allium cepa tests showed contrasting results. At high concentrations, olive wastes caused inhibition or suppression of mitosis. However, they did not produce induced anaphase aberrations. Data on reversion of Salmonella thyphimurium strains using the Ames test indicated that the olive wastes did not present mutagenic activity. Results from the field experiment showed that OMWW at a 500 m(3) ha(-1) had the highest values of both soil microbial activity and biomass after 3 months of the amendment application. This work adds new data for environmental risk assessment of olive industrial wastes. Direct use of olive wastes for agricultural purposes should be limited owing to their possible chemotoxic, phytotoxic and antimicrobial effects. Copyright © 2011 Society of Chemical Industry.

  10. Status and direction of waste minimization in the chemical and petrochemical industries

    Energy Technology Data Exchange (ETDEWEB)

    Englande Junior, A.J. [Tulane Univ., New Orleans, LA (United States). School of Public Health and Tropical Medicine

    1993-12-31

    This paper presents an evaluation of the status and direction of toxic/hazardous waste reduction in chemical and petrochemical industries from an international perspective. In almost all cases studied savings have resulted. The importance of pollution prevention by `clean technologies` instead of remediation is stressed. 6 refs., 4 tabs.

  11. Status and direction of waste minimization in the chemical and petrochemical industries

    Energy Technology Data Exchange (ETDEWEB)

    Englande, Junior, A J [Tulane Univ., New Orleans, LA (United States). School of Public Health and Tropical Medicine

    1994-12-31

    This paper presents an evaluation of the status and direction of toxic/hazardous waste reduction in chemical and petrochemical industries from an international perspective. In almost all cases studied savings have resulted. The importance of pollution prevention by `clean technologies` instead of remediation is stressed. 6 refs., 4 tabs.

  12. Physico-chemical treatment of liquid waste on an industrial plant for electrocoagulation.

    Science.gov (United States)

    Mlakar, Matej; Levstek, Marjetka; Stražar, Marjeta

    2017-10-01

    Wastewater from washing, oil separators, the metal processing and detergent industries, was tested and treated for treatment of different types of liquid waste at industrial level at Domžale-Kamnik Wastewater Treatment Plant (WWTP). The effect of implementing the electrocoagulation (EC) and flotation processes, respectively, is analysed and includes the duration of the EC implementation, voltage, number of electrodes, and chemical addition, as well as the pH effect and conductivity. The tests were performed not only on various types of liquid waste, but also on different mixtures of liquid waste. Laboratory analysis of the samples before and after EC have shown an effective reduction not only in organic loads in accordance with the COD (chemical oxygen demand) parameter, but also in mineral oil content, toxic metal concentration, and surfactants. The COD in liquid waste from the detergent industry was reduced by 73% and the content of surfactants by 64%. In liquid waste from the metal processing industry, the COD decreased by up to 95%, while the content of toxic metals decreased from 59 to 99%. Similar phenomena were shown in liquid waste from oil separators, where the COD was reduced to 33% and the concentration of mineral oils by 99%. Some of the liquid wastes were mixed together in the ratio 1:1, thus allowing testing of the operation of EC technology in heterogeneous liquid waste, where the final result proved to be effective cleaning as well. After treatment in the process of EC, the limit values of the treated water proved appropriate for discharge into the sewerage system.

  13. ESTIMATION OF INDUSTRIAL WASTE SAFETY BY THE “CHEMICAL OXYGEN DEMAND” INDEX

    Directory of Open Access Journals (Sweden)

    A. S. Kayshev

    2015-01-01

    Full Text Available One of the indices of industrial waste safety including distillers grains is chemical oxygen demand (COD, and its value (53591÷64184 mg O/dm3 shows that it can be considered as unsustainable waste. This high value of COD is conditioned by the absence of toxins in distillers grains, and by concentration of biologically active substances after which isolation the distillers grains index lowers by 74%. This allows considering the distillers grains as environmentally safe. The results received evidence the necessity for consideration of COD index only as an index of oxidized substances, but not the criteria of waste pollution.

  14. Use of wastes in high-temperature processes of the chemical industry; Verwertung von Abfaellen in Hochtemperaturprozessen der chemischen Industrie

    Energy Technology Data Exchange (ETDEWEB)

    Seifert, H. [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany); Domschke, T.; Steinebrunner, K. [BASF AG, Ludwigshafen am Rhein (Germany)

    1998-09-01

    The examples presented in this paper from diverse application areas of the chemical industry serve as an illustration of the many different ways in which wastes can be used for high-temperature processes in this branch. A review of the environmentally friendly concepts implemented at BASF AG in Ludwigshafen in the course of the past five years gives an idea of the immense potential opened up by a consistent application of the four-stage model for the prevention, reduction, and utilisation of wastes. In this period it was possible to reduce waste arisings by 34%, down from a potential 2 million tons, physically recycle 51%, and convert 11.5% to energy. This left a comparatively small fraction of 3.5%, or 70,000 tons, to be disposed of in an environmentally acceptable way. Furthermore, the amount of pollutants produced per tonne of products sold fell from 40.6 kg in 1987 to 6.7 kg in 1997. [Deutsch] Die Beispiele aus den unterschiedlichsten Anwendungsbereichen der chemischen Industrie koennen als Auswahl der vielfaeltigen Verwertungsmoeglichkeiten von Abfaellen in Hochtemperaturprozessen der Chemie betrachtet werden. Das immense Potential, das sich durch konsequente Anwendung des 4-Stufen-Modells zur Vermeidung, Verminderung und Verwertung von Abfaellen eroeffnet, zeigt sich in einer Fuenfjahresbilanz der umgesetzten Umweltschutzbetrachtungen in der BASF AG in Ludwigshafen. So konnten in diesem Zeitraum von potentiellen 2 Mio t Abfall/a ca. 34% vermieden und vermindert, 51% stofflich und 11,5% energetisch verwertet werden, so dass nur noch ein geringer Anteil von 3,5%, entsprechend ca. 70000 t/a, umweltgerecht entsorgt werden musste. Dies fuehrte auch zu einer drastischen Reduktion der auf der Tonne Verkaufsprodukt bezogenen Menge an umweltbelastenden Stoffen von 40,6 kg im Jahre 1987 auf 6,7 kg im Jahre 1997. (orig.)

  15. Valorization of industrial waste and by-product streams via fermentation for the production of chemicals and biopolymers.

    Science.gov (United States)

    Koutinas, Apostolis A; Vlysidis, Anestis; Pleissner, Daniel; Kopsahelis, Nikolaos; Lopez Garcia, Isabel; Kookos, Ioannis K; Papanikolaou, Seraphim; Kwan, Tsz Him; Lin, Carol Sze Ki

    2014-04-21

    The transition from a fossil fuel-based economy to a bio-based economy necessitates the exploitation of synergies, scientific innovations and breakthroughs, and step changes in the infrastructure of chemical industry. Sustainable production of chemicals and biopolymers should be dependent entirely on renewable carbon. White biotechnology could provide the necessary tools for the evolution of microbial bioconversion into a key unit operation in future biorefineries. Waste and by-product streams from existing industrial sectors (e.g., food industry, pulp and paper industry, biodiesel and bioethanol production) could be used as renewable resources for both biorefinery development and production of nutrient-complete fermentation feedstocks. This review focuses on the potential of utilizing waste and by-product streams from current industrial activities for the production of chemicals and biopolymers via microbial bioconversion. The first part of this review presents the current status and prospects on fermentative production of important platform chemicals (i.e., selected C2-C6 metabolic products and single cell oil) and biopolymers (i.e., polyhydroxyalkanoates and bacterial cellulose). In the second part, the qualitative and quantitative characteristics of waste and by-product streams from existing industrial sectors are presented. In the third part, the techno-economic aspects of bioconversion processes are critically reviewed. Four case studies showing the potential of case-specific waste and by-product streams for the production of succinic acid and polyhydroxyalkanoates are presented. It is evident that fermentative production of chemicals and biopolymers via refining of waste and by-product streams is a highly important research area with significant prospects for industrial applications.

  16. Proceedings of the 3. International conference on waste management in the chemical and petrochemical industries. Volume 1 and 2.

    Energy Technology Data Exchange (ETDEWEB)

    Lima, Francisco F.; Pereira Filho, Francisco A.; Almeida, Sergio A.S. [eds.

    1993-12-31

    To produce without pollution is today a mandate for the preservation of our society. To produce cleaner means to conserve energy and natural resources, to reduce the use of toxic substances, to invest in the evolution of products and production processes towards a minimum of residues. The Third International Conference on Waste Minimization in the Chemical and Petrochemical Industries addresses these challenging questions regarding waste minimization

  17. Proceedings of the 3. International conference on waste management in the chemical and petrochemical industries. Volume 1 and 2.

    Energy Technology Data Exchange (ETDEWEB)

    Lima, Francisco F; Pereira Filho, Francisco A; Almeida, Sergio A.S. [eds.

    1994-12-31

    To produce without pollution is today a mandate for the preservation of our society. To produce cleaner means to conserve energy and natural resources, to reduce the use of toxic substances, to invest in the evolution of products and production processes towards a minimum of residues. The Third International Conference on Waste Minimization in the Chemical and Petrochemical Industries addresses these challenging questions regarding waste minimization

  18. Concept for Recycling Waste Biomass from the Sugar Industry for Chemical and Biotechnological Purposes.

    Science.gov (United States)

    Modelska, Magdalena; Berlowska, Joanna; Kregiel, Dorota; Cieciura, Weronika; Antolak, Hubert; Tomaszewska, Jolanta; Binczarski, Michał; Szubiakiewicz, Elzbieta; Witonska, Izabela A

    2017-09-13

    The objective of this study was to develop a method for the thermally-assisted acidic hydrolysis of waste biomass from the sugar industry (sugar beet pulp and leaves) for chemical and biotechnological purposes. The distillates, containing furfural, can be catalytically reduced directly into furfurayl alcohol or tetrahydrofurfuryl alcohol. The sugars present in the hydrolysates can be converted by lactic bacteria into lactic acid, which, by catalytic reduction, leads to propylene glycol. The sugars may also be utilized by microorganisms in the process of cell proliferation, and the biomass obtained used as a protein supplement in animal feed. Our study also considered the effects of the mode and length of preservation (fresh, ensilage, and drying) on the yields of furfural and monosaccharides. The yield of furfural in the distillates was measured using gas chromatography with flame ionization detector (GC-FID). The content of monosaccharides in the hydrolysates was measured spectrophotometrically using enzymatic kits. Biomass preserved under all tested conditions produced high yields of furfural, comparable to those for fresh material. Long-term storage of ensiled waste biomass did not result in loss of furfural productivity. However, there were significant reductions in the amounts of monosaccharides in the hydrolysates.

  19. Effect of an industrial chemical waste on the uptake of cations by green oat

    Directory of Open Access Journals (Sweden)

    HORTENSIA RADULESCU

    2007-06-01

    Full Text Available Calcium carbonate, obtained as a waste in the industrial manufacture of magnesium carbonate and magnesium oxide from dolomites, can be applied in agriculture. The appreciable amounts of calcium and magnesium in this waste, together with impurities such as iron, zinc, manganese, chromium and copper compounds can be useful in soil amendment and plant nutrition. This paper presents preliminary results of the testing of several waste doses on soil, pursuing their effect on the uptake of cations by green oat (Avena sativa L.. The obtained results show an increase in the amount of calcium, magnesium, zinc and copper found in green oat plants, as well as a decrease of the content of iron and manganese with increasing waste dose. These results may be explained by lower absorptions of iron andmanganese because of the antagonistic effect created by high amounts of calcium and magnesium, as well as by the presence of copper and zinc.

  20. Chemicals Industry Vision

    Energy Technology Data Exchange (ETDEWEB)

    none,

    1996-12-01

    Chemical industry leaders articulated a long-term vision for the industry, its markets, and its technology in the groundbreaking 1996 document Technology Vision 2020 - The U.S. Chemical Industry. (PDF 310 KB).

  1. Physical-chemical characteristics of an eco-friendly binder using ternary mixture of industrial wastes

    Directory of Open Access Journals (Sweden)

    Nguyen, Hoang-Anh

    2015-09-01

    Full Text Available This study explores the physical-chemical characteristics of paste and mortar with an eco-friendly binder named as SFC cement, produced by a ternary mixture of industrial waste materials of ground granulated blast furnace slag (S, Class F fly ash (FFA, and circulating fluidized bed combustion fly ash (CFA. To trigger the hydration, the CFA, which acted as an alkaline-sulfate activator, was added to the blended mixture of slag and FFA. The water to binder ratio (W/B, curing regime, and FFA addition significantly affected the engineering performances and shrinkage/expansion of the SFC pastes and mortars. The SFC mortars had higher workability than that of ordinary Portland cement (OPC. With similar workability, the SFC mortars had compressive strengths and expansions comparable to OPC mortars. The main hydration products of the hardened SFC cement were ettringite (AFt and C-S-H/C-A-S-H. The transformation of the AFt to the monosulfates was observed as the hydration time increased.Este trabajo estudia las características fisicoquímicas de pastas y morteros con un ligante eco-amigable llamado cemento SFC, producido por una mezcla ternaria de materiales a partir de residuos industriales tales como escorias granuladas de alto horno (S, ceniza volante clase F (FFA, y cenizas volantes de combustión en lecho fluidizado circulante (CFA. Para desencadenar la hidratación, el CFA que actuó como un activador alcalino-sulfato se añadió a la mezcla combinada de escoria y FFA. La relación de agua/ligante (W/B, el tipo de curado, y la adición de FFA afectaron significativamente a las prestaciones mecánicas así como a la retracción/expansión de pastas y morteros de SFC. Los morteros SFC presentaron una trabajabilidad mayor que los correspondientes de cemento de Portland (OPC. Con una trabajabilidad similar, los morteros SFC presentaron resistencias mecánicas y expansión comparables a los morteros de OPC. Los principales productos de hidratación del

  2. High-grade use of waste propane streams in the Dutch chemical industry. An exploratory study in the context of the Chemical Industry Roadmap; Hoogwaardig gebruik van reststromen propaan in de Nederlandse chemische industrie. Een verkenning binnen de Routekaart Chemie

    Energy Technology Data Exchange (ETDEWEB)

    De Buck, A.; Afman, M.R.; Croezen, H.J.; Van Lieshout, M.

    2012-09-15

    In the context of the Dutch chemical industry's Roadmap the industry is actively seeking concrete ways of improving the efficiency of its products and processes. One option is to make higher-grade use of current waste streams, as feedstocks for other products, for example. This study focuses on propane waste streams from the oil and gas processing industry. Today these are used partly as fuel (fuel gas) but there are no technical barriers to converting propane to propylene, which can then be used as a feedstock. Higher-grade use of this particular waste stream leads to CO2 emission reductions in the production chain. Given the high market price of propylene, such a move may also be economically attractive. The study focuses on the Rotterdam region, because propane suppliers and companies seeking propylene are in closest proximity there [Dutch] In het kader van de Routekaart Chemie is de chemische industrie actief op zoek naar concrete opties om in haar processen en producten de efficiency te verhogen. Een route is daarbij om reststromen hoogwaardiger te benutten en in te zetten als grondstof voor andere producten. Dit onderzoek richt zich op reststromen propaan uit de olie- en gasverwerkende industrie. Deze worden nu deels als brandstof (stookgas) ingezet maar technisch is het mogelijk propaan om te zetten in propeen, dat als grondstof voor de chemische industrie kan worden gebruikt. Door het hoogwaardiger benutten van deze reststroom wordt in de keten een reductie van CO2 gerealiseerd. Tegelijk kan het economisch interessant zijn, vanwege de hoge marktprijzen van propeen. De studie focust op de regio Rotterdam, omdat leveranciers van propaan en afnemers van propeen daar het meest dichtbij elkaar gevestigd zijn.

  3. Industrial wastes from the boat-building sector in the Marche Region (Italy): a parametric and chemical-physical characterization.

    Science.gov (United States)

    Carchesio, M; Tatàno, F; Tosi, G; Trivellone, C H

    2013-01-01

    Using the renowned leisure boat-building sector in the Marche Region (Italy) as a case-study, this paper addresses the characterization of (1) the industrial waste generation from the building of composite material-based boats and (2) some chemical-physical properties of representative types of boat-building residues (plastic foam, hardened resin, fibre-reinforced composite residues, and sanding dust). A parametric evaluation based on the number of employees gave a representative unit generation rate per employee (UGRpE) of 1.47 tons(waste) employee(-1) year(-1) for the entire Marche regional boatbuilding district, whereas evaluations carried out separately for three case-study companies provided values of 1.56, 3.07, and 1.12 tons(waste) employee(-1) year(-1) as representative for a mass-produced motor boat builder (case-study company '1'), a customized sailing boat builder (case-study company '2'), and a mould and structural component builder (case-study company '3'), respectively. The original proposal and evaluation of two additional generation rates based on physical characteristics intrinsic to the manufactured product, i.e. the unit generation rate per boat area (UGRpA) and per boat weight (UGRpW), confirmed the higher waste generation for the sailing boat builder(representative UGRpA and UGRpW values of 0.35 tons(waste) m(-2)(boat) year(-1) and 2. 71 tons(waste) tons(-1)(boat) year(-1), respectively) compared with the motor boat builder (representative UGRpA and UGRpW values of 0.06 tons(waste) m(-2)(boat) year(-1) and 0.49 tons(waste) tons(-1)(boat) year(-1), respectively). The chemical-physical property characterization of the selected residues revealed the following aspects: a general condition of low moisture contents; significant ash contents in the glass- and carbon-fibre composite residues and the correlated sanding dust; and relatively high energy content values in the overall range 14,144-32,479 kJ kg(-1), expressed as the lower heating value.

  4. Hazardous industrial waste management

    International Nuclear Information System (INIS)

    Quesada, Hilda; Salas, Juan Carlos; Romero, Luis Guillermo

    2007-01-01

    The appropriate managing of hazardous wastes is a problem little dealed in the wastes management in the country. A search of available information was made about the generation and handling to internal and external level of the hazardous wastes by national industries. It was worked with eleven companies of different types of industrial activities for, by means of a questionnaire, interviews and visits, to determine the degree of integral and suitable handling of the wastes that they generate. It was concluded that exist only some isolated reports on the generation of hazardous industrial wastes and handling. The total quantity of wastes generated in the country was impossible to establish. The companies consulted were deficient in all stages of the handling of their wastes: generation, accumulation and storage, transport, treatment and final disposition. The lack of knowledge of the legislation and of the appropriate managing of the wastes is showed as the principal cause of the poor management of the residues. The lack of state or private entities entrusted to give services of storage, transport, treatment and final disposition of hazardous wastes in the country was evident. (author) [es

  5. Chemical and Microbial Dynamics during Composting of Herbal Pharmaceutical Industrial Waste

    Directory of Open Access Journals (Sweden)

    Farhan Zameer

    2010-01-01

    Full Text Available A study was performed to analyze the dynamics of chemical, biochemical and microbial parameters during composting of herbal pharmaceutical waste. All the parameters were analyzed at three different intervals of composting (1st, 15th and 60th days. Temperature of the compost pile was initially high (46.2 °C and on 60th day it dropped to 33.3 °C. The pH of the sample was initially acidic (2.39 and with the progress of decomposition gradually changed to neutrality (7.55. Electrical conductivity (EC value was high (3.8 mS during last day of composting compared to other stages. The activity of degradative enzymes namely amylase, invertase and urease were initially high (4.1, 4.79 mg of glucose/g/h and 0.19 mg of ammonia/g/h respectively while it decreased with composting. The beneficial microbial load was initially low and very high at the last stages of decomposition. The bioassay studies using compost extracts revealed that the 60th day old sample was not phytotoxic in nature.

  6. Glassceramics obtained from industrial waste

    Energy Technology Data Exchange (ETDEWEB)

    Cimdins, R.; Rozenstrauha, I.; Berzina, L. [Riga Technical University, Faculty of Chemical Technology, Biomaterials R and D Laboratory, 14/24 Azenes St., LV-1048 Riga (Latvia); Bossert, J.; Buecker, M. [Technisches Institut Materialwissenschaft, Friedrich-Schiller Universitaet, Loebdegraben 32, 07743 Jena (Germany)

    2000-06-01

    Large areas of Latvia are contaminated with industrial waste: metallurgical slag, fly-ash, etching refuse, peat, and coal ash as well as glass waste which often contain dangerous substances. From the environmental point of view this waste should be neutralised. As this waste also contains valuable chemical compounds, it can be considered as a raw material for the generation of new materials. One method of utilisation is to produce recycled materials - street plates, decorative tiles, or floor tiles. Dense sintered glassceramics with a water uptake of 0.34-3.23 wt.%, a final density of 2.93-3.05 g/cm{sup 3}, and a bending strength of 80-96 MPa have been created from industrial waste. The mast chemically durable glassceramics contained clay additions. Thus, the material containing only waste had a durability (mass loss) of 3.02% in 0.1 N HCl, while the composition containing 30% clay addition had a durability of 0.2% in 0.1 N HCl.

  7. Glasses obtained from industrial wastes

    International Nuclear Information System (INIS)

    Bortoluzzi, D.; Oliveira Fillho, J.; Uggioni, E.; Bernardin, A.M.

    2009-01-01

    This paper deals with the study of the vitrification mechanism as an inertization method for industrial wastes contaminated with heavy metals. Ashes from coal (thermoelectric), wastes from mining (fluorite and feldspar) and plating residue were used to compose vitreous systems planed by mixture design. The chemical composition of the wastes was determined by XRF and the formulations were melted at 1450 deg C for 2h using 10%wt of CaCO 3 (fluxing agent). The glasses were poured into a mold and annealed (600 deg C). The characteristic temperatures were determined by thermal analysis (DTA, air, 20 deg C/min) and the mechanical behavior by Vickers microhardness. As a result, the melting temperature is strongly dependent on silica content of each glass, and the fluorite residue, being composed mainly by silica, strongly affects Tm. The microhardness of all glasses is mainly affected by the plating residue due to the high iron and zinc content of this waste. (author)

  8. Steel Industry Wastes.

    Science.gov (United States)

    Schmidtke, N. W.; Averill, D. W.

    1978-01-01

    Presents a literature review of wastes from steel industry, covering publications of 1976-77. This review covers: (1) coke production; (2) iron and steel production; (3) rolling operations; and (4) surface treatment. A list of 133 references is also presented. (NM)

  9. Radioactive wastes of Nuclear Industry

    International Nuclear Information System (INIS)

    1995-01-01

    This conference studies the radioactive waste of nuclear industry. Nine articles and presentations are exposed here; the action of the direction of nuclear installations safety, the improvement of industrial proceedings to reduce the waste volume, the packaging of radioactive waste, the safety of radioactive waste disposal and environmental impact studies, a presentation of waste coming from nuclear power plants, the new waste management policy, the international panorama of radioactive waste management, the international transport of radioactive waste, finally an economic analysis of the treatment and ultimate storage of radioactive waste. (N.C.)

  10. 2,3-Butanediol Production by Acetogenic Bacteria, an Alternative Route to Chemical Synthesis, Using Industrial Waste Gas ▿ †

    Science.gov (United States)

    Köpke, Michael; Mihalcea, Christophe; Liew, FungMin; Tizard, Joseph H.; Ali, Mohammed S.; Conolly, Joshua J.; Al-Sinawi, Bakir; Simpson, Séan D.

    2011-01-01

    2,3-Butanediol (23BD) is a high-value chemical usually produced petrochemically but which can also be synthesized by some bacteria. To date, the best microbial 23BD production rates have been observed using pathogenic bacteria in fermentation systems that depend on sugars as the carbon and energy sources for product synthesis. Here we present evidence of 23BD production by three nonpathogenic acetogenic Clostridium species—Clostridium autoethanogenum, C. ljungdahlii, and C. ragsdalei—using carbon monoxide-containing industrial waste gases or syngas as the sole source of carbon and energy. Through an analysis of the C. ljungdahlii genome, the complete pathway from carbon monoxide to 23BD has been proposed. Homologues of the genes involved in this pathway were also confirmed for the other two species investigated. A gene expression study demonstrates a correlation between mRNA accumulation from 23BD biosynthetic genes and the onset of 23BD production, while a broader expression study of Wood-Ljungdahl pathway genes provides a transcription-level view of one of the oldest existing biochemical pathways. PMID:21685168

  11. The renewable chemicals industry

    DEFF Research Database (Denmark)

    Christensen, Claus H.; Rass-Hansen, J.; Marsden, Charlotte Clare

    2008-01-01

    per kilogram of desired product to illustrate in which processes the use of renewable resources lead to the most substantial reduction of CO2 emissions. The steps towards a renewable chemicals industry will most likely involve intimate integration of biocatalytic and conventional catalytic processes......The possibilities for establishing a renewable chemicals industry featuring renewable resources as the dominant feedstock rather than fossil resources are discussed in this Concept. Such use of biomass can potentially be interesting from both an economical and ecological perspective. Simple...

  12. Gamma radiation treatment of waste waters from textile industries in ...

    African Journals Online (AJOL)

    Effects of gamma irradiation alone, and in combination with chemical treatment on color, odor, chemical oxyg-en demand (COD) and suspended solids in waste waters from textile industries in Ghana were studied to explore the potential of alternative and innovative processes for treatment of industrial waste waters. Waste ...

  13. Methods and instruments for the ecological assessment of the treatment of solvent wastes in the chemical industry; Methoden und Instrumente zur oekologischen Bewertung der Abfall-Loesungsmittelbehandlung in der chemischen Industrie

    Energy Technology Data Exchange (ETDEWEB)

    Capello, Ch.

    2006-07-01

    This final report for the Swiss Federal Office of Energy (SFOE) presents the results of a project which looked at the treatment of solvent wastes in the chemical industry and its ecological impact. The development of a method based on the life-cycle-analysis (LCA) approach is described. The LCA methodology is to provide support for decision-making in the area of solvent waste disposal in the chemical industry. Various methods of disposal, such as distillation or incineration are looked at. The results of calculations using a software tool called 'ecosolvent' are presented and discussed. The 15 most important solvents and their quantities as used in the 6 facilities examined, are listed. The functioning of the ecosolvent software is discussed and illustrated in a flow-diagram. Along with detailed results, a few qualitative rules of thumb are quoted for the treatment of solvent wastes.

  14. Chemical and petrochemical industry

    Science.gov (United States)

    Staszak, Katarzyna

    2018-03-01

    The potential sources of various metals in chemical and petrochemical processes are discussed. Special emphasis is put on the catalysts used in the industry. Their main applications, compositions, especially metal contents are presented both for fresh and spent ones. The focus is on the main types of metals used in catalysts: the platinum-group metals, the rare-earth elements, and the variety of transition metals. The analysis suggested that chemical and petrochemical sectors can be considered as the secondary source of metals. Because the utilization of spent refinery catalysts for metal recovery is potentially viable, different methods were applied. The conventional approaches used in metal reclamation as hydrometallurgy and pyrometallurgy, as well as new methods include bioleaching, were described. Some industrial solutions for metal recovery from spent solution were also presented.

  15. Disposal of mixed radioactive and chemical waste

    International Nuclear Information System (INIS)

    Moghissi, A.A.

    1986-01-01

    The treatment of waste by dilution was practiced as long as nature provided sufficient unpolluted air, water, and land. The necessity for treatment, including containment and disposal of wastes is, however, relatively new. Initially, waste products from manufacturing processes were looked upon as a potential resource. The industries of Western Europe, short of raw materials, tried to recover as many chemical compounds as possible from industrial waste. However, the availability of abundant and cheap petroleum during the fifties changes this practice, at least for a short period

  16. Waste management and chemical inventories

    Energy Technology Data Exchange (ETDEWEB)

    Gleckler, B.P.

    1995-06-01

    This section of the 1994 Hanford Site Environmental Report summarizes the classification and handling of waste at the Hanford Site. Waste produced at the Hanford Site is classified as either radioactive, nonradioactive, or mixed waste. Radioactive wastes are further categorized as transuranic, high-level, and low-level. Mixed waste may contain both radioactive and hazardous nonradioactive substances. This section describes waste management practices and chemical inventories at the site.

  17. Waste management and chemical inventories

    International Nuclear Information System (INIS)

    Gleckler, B.P.

    1995-01-01

    This section of the 1994 Hanford Site Environmental Report summarizes the classification and handling of waste at the Hanford Site. Waste produced at the Hanford Site is classified as either radioactive, nonradioactive, or mixed waste. Radioactive wastes are further categorized as transuranic, high-level, and low-level. Mixed waste may contain both radioactive and hazardous nonradioactive substances. This section describes waste management practices and chemical inventories at the site

  18. The problem of industrial wastes

    International Nuclear Information System (INIS)

    Hamdan, Fouad

    1998-01-01

    The paper is the result of a feasibility study conducted for the Green peace Office in Lebanon. The overall goal of the study was to work towards implementing a national waste management plan and to combat the import of hazardous wastes from developing countries.The author focuses on the illegal trade of industrial wastes from developed to under developed countries. The trade of toxic wastes causes on environmental pollution. As for Lebanese industries, the main problem is toxic industrial wastes. About 4000 tones/day of domestic wastes are produced in Lebanon. 326000 tones of industrial wastes contain toxic substances are annually produced and wastes growth rate is expected to increase to one million tone/year in 2010. A disaster is threatening Lebanon especially that no policy were taken to deal with the huge growth of wastes. This problem affect on population health especially in the region of Bourj Hammoud. Analysis of ground water in the region of Chekka, confirm the existence of water pollution caused by toxic materials In addition, analysis of Petro coke used in the National Lebanese Cement Industry, contain a high rate of Polycyclic Aromatic Hydrocarbons. Green peace is aware of the danger of wastes in air, water and land pollution and preventing environment of any source of pollution this will certainly lead to a sustainable development of the country

  19. Physico-Chemical Studies Involving Incorporation of Radioactive and Industrial Waste In Cement-Epoxy Resin Matrix

    International Nuclear Information System (INIS)

    Sayed, M.S.; Hafez, N.

    1999-01-01

    Cement and epoxy resin as chemical additives are proposed to incorporate different types of wastes. The study was extended to prepare different mixtures of cement and epoxy resin in presence of some toxic ions. The studied ions were Cd II, Ni II, Cu II, Fe III, Ce IV, 154+152 Eu, phenol and toluene. The physical, mechanical and leaching properties of the mixtures were studied. The thermal analysis and infrared spectra were also investigated. It was observed that all the studied properties of the epoxy modified cement as a disposal matrix was improved

  20. Ironing out industrial wastes

    International Nuclear Information System (INIS)

    Valenti, M.

    1996-01-01

    This article describes a hazardous waste treatment known as the catalytic extraction process, which also stabilizes and reduces low-level radioactive wastes to a fraction of their original volume, easing their disposal. It uses molten iron and other metals to convert hazardous wastes into useful materials

  1. Chemical Waste Management and Disposal.

    Science.gov (United States)

    Armour, Margaret-Ann

    1988-01-01

    Describes simple, efficient techniques for treating hazardous chemicals so that nontoxic and nonhazardous residues are formed. Discusses general rules for management of waste chemicals from school laboratories and general techniques for the disposal of waste or surplus chemicals. Lists specific disposal reactions. (CW)

  2. EXOPOLYSACCHARIDES SYNTHESIS ON INDUSTRIAL WASTES

    Directory of Open Access Journals (Sweden)

    T.P.

    2016-04-01

    Full Text Available Data from the literature and our own studies on the synthesis of microbial exopolysaccharides on various industrial waste (food industry, agricultural sector, biodiesel production, etc. are reviewed here. Utilization of industrial waste to obtain exopolysaccharides will solve not only the problem of secondary raw materials accumulation, but also will reduce the costs of the biosynthesis of practically valuable metabolites. In addition, some kinds of waste have a number of advantages compared to traditional carbohydrate substrates: aside from environmental health benefits, there are technological ones, like the presence of growth factors. There is also no need to use anti-foam substances and substrate sterilization in the latter case.

  3. Radioactive wastes. Their industrial management

    International Nuclear Information System (INIS)

    Lavie, J.M.

    1982-01-01

    This paper introduces a series that will review the present situation in the field of long-term management of radioactive wastes. Both the meaning and the purposes of an industrial management of radioactive wastes are specified. This short introduction is complemented by outline of data on the French problem [fr

  4. The use of ionizing radiations in the treatment of liquid and solid waste; biological and physico-chemical effects and industrial study

    International Nuclear Information System (INIS)

    Gallien, C.L.

    1977-01-01

    Short recycling of waste water and the use of liquid or dehydrated sludge as natural manure for agriculture, or animal supplement feed is of great economical and ecological interest. However, it requires strong disinfection. Treatment with ionizing radiation can be used as a complement to conventional methods in the treatment of liquid and solid wastes. An experiment conducted with a high-energy electron beam linear accellerator (10 MeV) is presented. Degradation of undesirable metabolites in wastes occurs at a dose of 50 krad. Undesirable seeds, present in sludge, are destroyed with a 200-krad dose. The same dose is sufficient for parasitic and bacterial disinfection (DL 90). Destruction of poliovirus (DL 90) is obtained at 400 krad. Higher doses (1000-2000 krad) produce mineralisation of toxic organic mercury or reduce some toxic chemical pollutants present in sludge and improve flocculation. Industrial study shows that waste treatment with high-energy electron beams is technically and economically feasible. The design for a treatment unit of 5 MCi cobalt-equivalent, with a capacity of 500 t/Mrad/24h is presented, with indicative cost calculation

  5. Utilization of inulin-containing waste in industrial fermentations to produce biofuels and bio-based chemicals.

    Science.gov (United States)

    Hughes, Stephen R; Qureshi, Nasib; López-Núñez, Juan Carlos; Jones, Marjorie A; Jarodsky, Joshua M; Galindo-Leva, Luz Ángela; Lindquist, Mitchell R

    2017-04-01

    Inulins are polysaccharides that belong to an important class of carbohydrates known as fructans and are used by many plants as a means of storing energy. Inulins contain 20 to several thousand fructose units joined by β-2,1 glycosidic bonds, typically with a terminal glucose unit. Plants with high concentrations of inulin include: agave, asparagus, coffee, chicory, dahlia, dandelion, garlic, globe artichoke, Jerusalem artichoke, jicama, onion, wild yam, and yacón. To utilize inulin as its carbon and energy source directly, a microorganism requires an extracellular inulinase to hydrolyze the glycosidic bonds to release fermentable monosaccharides. Inulinase is produced by many microorganisms, including species of Aspergillus, Kluyveromyces, Penicillium, and Pseudomonas. We review various inulinase-producing microorganisms and inulin feedstocks with potential for industrial application as well as biotechnological efforts underway to develop sustainable practices for the disposal of residues from processing inulin-containing crops. A multi-stage biorefinery concept is proposed to convert cellulosic and inulin-containing waste produced at crop processing operations to valuable biofuels and bioproducts using Kluyveromyces marxianus, Yarrowia lipolytica, Rhodotorula glutinis, and Saccharomyces cerevisiae as well as thermochemical treatments.

  6. Nuclear industry - challenges in chemical engineering

    International Nuclear Information System (INIS)

    Sen, S.; Sunder Rajan, N.S.; Balu, K.; Garg, R.K.; Murthy, L.G.K.; Ramani, M.P.S.; Rao, M.K.; Sadhukhan, H.K.; Venkat Raj, V.

    1978-01-01

    As chemical engineering processes and operations are closely involved in many areas of nuclear industry, the chemical engineer has a vital role to play in its growth and development. An account of the major achievements of the Indian chemical engineers in this field is given with view of impressing upon the faculty members of the Indian universities the need for taking appropriate steps to prepare chemical engineers suitable for nuclear industry. Some of the major achievements of the Indian chemical engineers in this field are : (1) separation of useful minerals from beach sand, (2) preparation of thorium nitrate of nuclear purity from monazite, (3) processing of zircon sand to obtain nuclear grade zirconium and its separation from hafnium to obtain zirconium metal sponge, (4) recovery of uranium from copper tailings, (5) economic recovery of nuclear grade uranium from low grade uranium ores found in India, (6) fuel reprocessing, (7) chemical processing of both low and high level radioactive wastes. (M.G.B.)

  7. Chemical Industry Bandwidth Study

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2006-12-01

    The Chemical Bandwidth Study provides a snapshot of potentially recoverable energy losses during chemical manufacturing. The advantage of this study is the use of "exergy" analysis as a tool for pinpointing inefficiencies.

  8. Exergetic comparison of food waste valorization in industrial bread production

    NARCIS (Netherlands)

    Zisopoulos, F.K.; Moejes, S.N.; Rossier Miranda, F.J.; Goot, van der A.J.; Boom, R.M.

    2015-01-01

    This study compares the thermodynamic performance of three industrial bread production chains: one that generates food waste, one that avoids food waste generation, and one that reworks food waste to produce new bread. The chemical exergy flows were found to be much larger than the physical exergy

  9. Industrial management of radioactive wastes

    International Nuclear Information System (INIS)

    Lavie, J.M.

    1984-01-01

    This article deals with the present situation in France concerning radioactive waste management. For the short and medium term, that is to say processing and disposal of low and medium level radioactive wastes, there are industrial processes giving all the guarantees for a safe containment, but improvements are possible. For the long term optimization of solution requires more studies of geologic formations. Realization emergency comes less from the waste production than the need to optimize the disposal techniques. An international cooperation exists. All this should convince the public opinion and should develop planning and realization [fr

  10. Quantitative and qualitative investigation of industrial solid waste in industrial plants located between Tehran and Karaj

    Directory of Open Access Journals (Sweden)

    M.R. Gohari

    2011-07-01

    Full Text Available Background and aims   Rapid population growth, industrial development, urbanization culture propagation and excessive material consumption are the most important factor which caused over increasing of municipal, industrial and agricultural waste in human society. Inappropriate disposal of generated waste in recent years created several environmental menace and crisis in human society.   methods   For investigation about existent situation of industrial waste generation questionnaire had been used. This questionnaire was catered by Iran environmental protection organization. Aforementioned questionnaire contained 45 questions about combination, quality and quantity of industrial waste. Total number of more than 50 personnel industry was 287 . But sample contained 50 randomly selected industries. Gathered data have been analyzed with spss 18.   Results  Total generated industrial waste was 123451KG per day which had volume equal to 781 cubic meters per day. Generated waste capitation per every worker was 5.8 KG. Maximum frequency of industrial was related to machinery and equipment group which maximum generated waste was related to this industrial group too. Maximum hazardous waste was for inflammable waste with 34 weight percent. Major hazardous waste generating industrial was chemical and plastic making industry.   Conclusion  yielded result from this investigation has shown that significant relation existed between waste production rate and personnel number. The more personnel are, the more waste production increase.

  11. Waste audit pada industri penyamakan kulit

    Directory of Open Access Journals (Sweden)

    Prayitno Prayitno

    1999-07-01

    Full Text Available Waste audit is new environmental activities. to the Indonesia public and the large part of industrial community it is one of the environmental audit activities. Waste audit aims to identify whether the waste that by the industry waste so that metods for minimizing the waste can be found. In the leather tanning industry wasted audit is performend for every step pg the process, started from the raw material strage to the fishing ptocess.

  12. Waste Management in Industrial Construction: Investigating Contributions from Industrial Ecology

    Directory of Open Access Journals (Sweden)

    Larissa A. R. U. Freitas

    2017-07-01

    Full Text Available The need for effective construction waste management is growing in importance, due to the increasing generation of construction waste and to its adverse impacts on the environment. However, despite the numerous studies on construction waste management, recovery of construction waste through Industrial Symbiosis and the adoption of other inter-firm practices, comprised within Industrial Ecology field of study, have not been fully explored. The present research aims to investigate Industrial Ecology contributions to waste management in industrial construction. The waste management strategies adopted in two industrial construction projects in Brazil are analyzed. The main waste streams generated are identified, recycling and landfilling diversion rates are presented and waste recovery through Industrial Symbiosis is discussed. A SWOT analysis was carried out. Results demonstrate that 9% of the waste produced in one of the projects was recovered through Industrial Symbiosis, while in the other project, waste recovery through Industrial Symbiosis achieved the rate of 30%. These data reveal Industrial Symbiosis’ potential to reduce landfilling of industrial construction wastes, contributing to waste recovery in construction. In addition, results show that industrial construction projects can benefit from the following synergies common in Industrial Ecology place-based approaches: centralized waste management service, shared waste management infrastructure and administrative simplification.

  13. Bioremediation of industrial waste through mushroom cultivation.

    Science.gov (United States)

    Kulshreshtha, Shweta; Mathur, Nupur; Bhatnagar, Pradeep; Jain, B L

    2010-07-01

    Handmade paper and cardboard industries are involved in processing of cellulosic and ligno-cellulosic substances for making paper by hand or simple machinery. In the present study solid sludge and effluent of both cardboard and handmade paper industries was collected for developing a mushroom cultivation technique to achieve zero waste discharges. Findings of present research work reveals that when 50% paper industries waste is used by mixing with 50% (w/w) wheat straw, significant increase (96.38%) in biological efficiency over control of wheat straw was observed. Further, cultivated basidiocarps showed normal morphology of stipe and pileus. Cross section of lamellae did not show any abnormality in the attachment of basidiospores, hymenal trama and basidium. No toxicity was found when fruiting bodies were tested chemically.

  14. The chemical industry of Ukraine

    International Nuclear Information System (INIS)

    Novikov, I.N.

    1995-01-01

    This work deals with the chemical industry of Ukraine and more particularly with the restructuring proposed by the Ministry of Industry. After having presented some generalities the author focuses on the restructuring programme which includes the improvement of the fertilizers supply for agriculture, the development of facilities for basic organic synthesis, the increase of petroleum based chemicals production, the increase of consumer products production and the reorientation of the chemical industry to more accessible and alternative sources of raw materials such as black and brown coal, oil shale, coke, oil-refining gases, plant raw materials... (O.L.)

  15. Chemical treatment of radioactive wastes

    International Nuclear Information System (INIS)

    Pottier, P.E.

    1968-01-01

    This is the third manual of three commissioned by the IAEA on the three principal techniques used in concentrating radioactive liquid wastes, namely chemical precipitation, evaporation and ion exchange. The present manual deals with chemical precipitation by coagulation-flocculation and sedimentation, commonly called ''chemical treatment'' of low-activity wastes. Topics discussed in the manual are: (i) principles of coagulation on flocculation and sedimentation and associated processes; (ii) process and equipment; (iii) conditioning and disposal of flocculation sludge; (iv) sampling and the equipment required for experiments; and (v) factors governing the selection of processes. 99 refs, 17 figs, 4 tabs

  16. Industrial waste heat for district heating

    International Nuclear Information System (INIS)

    Heitner, K.L.; Brooks, P.P.

    1982-01-01

    Presents 2 bounding evaluations of industrial waste heat availability. Surveys waste heat from 29 major industry groups at the 2-digit level in Standard Industrial Codes (SIC). Explains that waste heat availability in each industry was related to regional product sales, in order to estimate regional waste heat availability. Evaluates 4 selected industries at the 4-digit SIC level. Finds that industrial waste heat represents a significant energy resource in several urban areas, including Chicago and Los Angeles, where it could supply all of these areas residential heating and cooling load. Points out that there is a strong need to evaluate the available waste heat for more industries at the 4-digit level. Urges further studies to identify other useful industrial waste heat sources as well as potential waste heat users

  17. Characterization and environmental risk assessment of heavy metals in construction and demolition wastes from five sources (chemical, metallurgical and light industries, and residential and recycled aggregates).

    Science.gov (United States)

    Gao, Xiaofeng; Gu, Yilu; Xie, Tian; Zhen, Guangyin; Huang, Sheng; Zhao, Youcai

    2015-06-01

    Total concentrations of heavy metals (Cu, Zn, Pb, Cr, Cd, and Ni) were measured among 63 samples of construction and demolition (C&D) wastes collected from chemical, metallurgical and light industries, and residential and recycled aggregates within China for risk assessment. The heavy metal contamination was primarily concentrated in the chemical and metallurgical industries, especially in the electroplating factory and zinc smelting plant. High concentrations of Cd were found in light industry samples, while the residential and recycled aggregate samples were severely polluted by Zn. Six most polluted samples were selected for deep research. Mineralogical analysis by X-ray fluorescence (XRF) spectrometry and X-ray diffraction (XRD), combined with element speciation through European Community Bureau of Reference (BCR) sequential extraction, revealed that a relatively slight corrosion happened in the four samples from electroplating plants but high transfer ability for large quantities of Zn and Cu. Lead arsenate existed in the acid extractable fraction in CI7-8 and potassium chromium oxide existed in the mobility fraction. High concentration of Cr could be in amorphous forms existing in CI9. The high content of sodium in the two samples from zinc smelter plants suggested severe deposition and erosion on the workshop floor. Large quantities of Cu existed as copper halide and most of the Zn appeared to be zinc, zinc oxide, barium zinc oxide, and zincite. From the results of the risk assessment code (RAC), the samples from the electroplating factory posed a very high risk of Zn, Cu, and Cr, a high risk of Ni, a middle risk of Pb, and a low risk of Cd. The samples from the zinc smelting plant presented a high risk of Zn, a middle risk of Cu, and a low risk of Pb, Cr, Cd, and Ni.

  18. Hong kong chemical waste treatment facilities: a technology overview

    Energy Technology Data Exchange (ETDEWEB)

    Siuwang, Chu [Enviropace Ltd., Hong Kong (Hong Kong)

    1993-12-31

    The effective management of chemical and industrial wastes represents one of the most pressing environmental problems confronting the Hong Kong community. In 1990, the Hong Kong government contracted Enviropace Limited for the design, construction and operation of a Chemical Waste Treatment Facility. The treatment and disposal processes, their integration and management are the subject of discussion in this paper

  19. Hong kong chemical waste treatment facilities: a technology overview

    Energy Technology Data Exchange (ETDEWEB)

    Siuwang, Chu [Enviropace Ltd., Hong Kong (Hong Kong)

    1994-12-31

    The effective management of chemical and industrial wastes represents one of the most pressing environmental problems confronting the Hong Kong community. In 1990, the Hong Kong government contracted Enviropace Limited for the design, construction and operation of a Chemical Waste Treatment Facility. The treatment and disposal processes, their integration and management are the subject of discussion in this paper

  20. The chemical industry - friend to the environment?

    International Nuclear Information System (INIS)

    1992-01-01

    ''The Chemical Industry - Friend to the Environment?'' was a symposium organised by the North East Region committee of the Industrial Division of the Royal Society of Chemistry. This volume contains typescripts from all the lectures given at the symposium. The general public appreciate the material comforts the Chemical Industry provides, for example textiles, ceramics, steel, speciality chemicals, drugs, prosthetics etc. However, for many their comfort is spoiled by the chemical poisoning of the environment through slag heaps, beaches and countryside littered with non-biodegradable unsightly plastic containers, poor air quality through NO x , CO 2 and chlorofluorocarbon emissions, and of course, nuclear waste. The occasional spillage of hazardous chemicals through road, rail and sea accidents do nothing to improve the Industry's image. The majority of these topics were discussed, though no one presumed to know how to remove the problems entirely but many suggestions were put forward as to how this might be achieved. Of the 13 papers presented three were specifically concerned with recycling of plastics, 9 with the environmental impacts of chemicals and one, which is indexed separately, was concerned with radioactive discharges into the environment from the Sellafield reprocessing plant. (Author)

  1. Waste Management in Industrial Construction: Investigating Contributions from Industrial Ecology

    OpenAIRE

    Larissa A. R. U. Freitas; Alessandra Magrini

    2017-01-01

    The need for effective construction waste management is growing in importance, due to the increasing generation of construction waste and to its adverse impacts on the environment. However, despite the numerous studies on construction waste management, recovery of construction waste through Industrial Symbiosis and the adoption of other inter-firm practices, comprised within Industrial Ecology field of study, have not been fully explored. The present research aims to investigate Industrial Ec...

  2. Chemical decontamination of radioactive waste

    International Nuclear Information System (INIS)

    Mohamed, H.I.

    2006-01-01

    Radioactive wastes are generated in a number of different kinds of facilities and arise in a wide range of concentrations of radioactive materials and in a variety of physical and chemical forms. There is also a variety of alternatives for treatment and conditioning of the wastes prior disposal. The importance of treatment of radioactive waste for protection of human and environment has long been recognized and considerable experience has gained in this field. Generally, the methods used for treatment of radioactive wastes can be classified into three type's biological, physical and chemical treatment this physical treatment it gives good result than biological treatment. Chemical treatment is fewer hazards and gives good result compared with biological and physical treatments. Chemical treatment is fewer hazards and gives good result compared with biological and physical treatments. In chemical treatment there are different procedures, solvent extraction, ion exchange, electro dialysis but solvent extraction is best one because high purity can be optioned on the other hand the disadvantage that it is expensive. Beside the solvent extraction technique one can be used is ion exchange which gives reasonable result, but requires pretreatment that to avoid in closing of column by colloidal and large species. Electro dialysis technique gives quite result but less than solvent extraction and ion exchange technique the advantage is a cheep.(Author)

  3. Grand Rounds: An Outbreak of Toxic Hepatitis among Industrial Waste Disposal Workers

    OpenAIRE

    Cheong, Hae-Kwan; Kim, Eun A; Choi, Jung-Keun; Choi, Sung-Bong; Suh, Jeong-Ill; Choi, Dae Seob; Kim, Jung Ran

    2006-01-01

    Context Industrial waste (which is composed of various toxic chemicals), changes to the disposal process, and addition of chemicals should all be monitored and controlled carefully in the industrial waste industry to reduce the health hazard to workers. Case presentation Five workers in an industrial waste plant developed acute toxic hepatitis, one of whom died after 3 months due to fulminant hepatitis. In the plant, we detected several chemicals with hepatotoxic potential, including pyridine...

  4. Toxicological evaluation of complex industrial wastes: Implications for exposure assessment

    Energy Technology Data Exchange (ETDEWEB)

    DeMarini, D.M.; Gallagher, J.E.; Houk, V.S.; Simmons, J.E.

    1989-01-01

    A variety of short-term bioassays to construct a battery of tests that could be used for assessing the biological effects of potentially hazardous complex industrial wastes were evaluated. Ten samples were studied for hepatotoxicity: These samples and an additional five were studied for mutagenicity. Although the data are limited to these samples, the results suggest that the Salmonella assay (either TA98 or TA100) or a prophage-induction assay (both in the presence of S9) in combination with determination of relative liver weight and levels of a set of serum enzymes in rats would provide a battery of tests suitable to characterize complex industrial wastes for mutagenic and hepatotoxic potential. The biological activities exhibited by the wastes were not readily predicted by the chemical profiles of the wastes, emphasizing the importance of characterizing potentially hazardous complex industrial wastes by both chemical and biological means.

  5. The industrial waste landfill of Bonfol (Switzerland)

    Energy Technology Data Exchange (ETDEWEB)

    Arnold, C.G.; Bentz, R. [Ciba Specialty Chemicals Inc., Basel (Switzerland); Fischer, M.; Huerzeler, R.A.; Matter, B.; Munz, C.D.

    2003-07-01

    The landfill for industrial waste in Bonfol (Switzerland) was installed in 1961 in an waterproof clay pit and was run until 1976 by the bci, the Basel chemical industry, to dispose off their industrial waste originating from chemical production. For the first time in Europe chemical wastes were deposited in a special area selected according to geological criteria. Groundwater and surface waters have been continuously supervised since the beginning of the activities in Bonfol in 1961. After the landfill was totally filled up, it was covered by a clay layer. In the years 1980/81 the monitoring program discovered that the cover of the landfill was leaking and that the pit was slowly filled up with water. Some exfiltrations resulted. It was important to overcome the critical situation by the implementation of immediate measures, e.g. pumping and removal of leachate. Different remediation options were studied at that time, among other the excavation and final disposal of the contents of the landfill. On October 17, 2000 a voluntary agreement between the authorities and bci ws signed. On May 15, 2001, bci presented the result of the study of remedial options. Excavation / incineration in European incinerators or in-situ vitrification, with a suboption excavation/on-site vitrification, were seen as the most promising ones. At the end of 2001 the option of the in-situ vitrification was dropped because of the resulting public and political resistance towards this technology. The remaining options are being evaluated thoroughly at the moment to prepare the basis for a decision on the clean-up project. (orig.)

  6. Physical-Chemical Characterization of Solid Waste Generated in the Water Industry: Case Study of the Water Treatment Stations of the Metropolitan Region of Recife

    Directory of Open Access Journals (Sweden)

    Rosângela Gomes Tavares

    2017-12-01

    Full Text Available The objective of this research is to characterize the solid waste, commonly known as sludge, from the water treatment industry. Six main water treatment plants (Alto do Céu, Botafogo, Caixa d'água, Gurjaú, Suape and Tapacurá were selected from the Metropolitan Region of Recife, managed by Companhia Pernambucana de Saneamento. Nine samples were collected in the eleven month period in the discharge of the sludge from the decanters. These samples were characterized physico-chemically, based on the methodology of the Standard Methods for the Examination of Water and Wastewater (2012. The results indicated average humidity of 93%, average COD around 30 g/L and BOD of 4.5 g/L, indicating sludge of low biodegradability. The average values of total solids were 72 g/L, with 75% corresponding to fixed residues and 25% to volatiles. High concentrations of aluminum (1000 mg/L were observed, due to the use of aluminum sulphate as a coagulant, and iron, around 500 mg/L. This study assists the manager in the decision making of the sustainable management of the sludge, mainly in relation to the final disposal.

  7. Industrial waste and pollution in Mongolia

    Energy Technology Data Exchange (ETDEWEB)

    Dolgormaa, L. [Minstry of Nature and Environment, Ulaanbaatar (Mongolia)

    1996-12-31

    This paper very briefly outlines hazardous waste management issues, including regulations, in Mongolia. Air, water, and soil pollutants are identified and placed in context with climatic, social, and economic circumstances. The primary need identified is technology for the collection and disposal of solid wastes. Municipal waste problems include rapid urbanization and lack of sanitary landfills. Industrial wastes of concern are identified from the mining and leather industries. 4 refs., 2 tabs.

  8. Management of waste solvents in the chemical industry - An ecological comparison of distillation and incineration; Abfallloesungsmittelbewirtschaftung in der chemischen Industrie. Ein oekologischer Vergleich von Rektifikation und Verbrennung

    Energy Technology Data Exchange (ETDEWEB)

    Hofstetter, T.B.

    2002-07-01

    This final report for the Swiss Federal Office of Energy (SFOE) presents the results of a project in which two methods of dealing with solvent wastes were compared - distillation or incineration. The results of an analysis made of two case studies, a waste-solvent incineration plant and a batch distillation column, are presented. These were used to develop a simplified evaluation model for the two methods. The three methods used for the analysis of environmental impact are described - Eco-Indicator 99, ecological scarcity and primary energy demand. The authors note that the distillation model cannot be generally applied as the process is very dependent on the particular mixture of solvents being distilled and that the energy assessment method is dependent on the particular form of energy substituted by the energy produced in the incineration system. The evaluation model developed was used for 5 different mixtures of solvents. The results of the project show that apart from the availability of an accurate evaluation model, the life-cycle inventories for petrochemical production of solvents are limited and may compromise the applicability of the model to other mixtures of solvents.

  9. Nuclear industry - challenges in chemical engineering

    International Nuclear Information System (INIS)

    Sen, S.; Sunder Rajan, N.S.; Balu, K.; Garg, R.K.; Murthy, L.G.K.; Ramani, M.P.S.; Rao, M.K.; Sadhukhan, H.K.; Venkat Raj, V.

    1978-01-01

    Chemical engineering processes and operations are closely involved in every step of the nuclear fuel cycle. Starting from mining and milling of the ore through the production of fuel and other materials and their use in nuclear reactors, fuel reprocessing, fissile material recycle and treatment and disposal of fission product wastes, each step presents a challenge to the chemical engineer to evolve and innovate processes and techniques for more efficient utilization of the energy in the atom. The requirement of high recovery of the desired components at high purity levels is in itself a challenge. ''Nuclear Grade'' specifications for materials put a requirement which very few industries can satisfy. Recovery of uranium and thorium from low grade ores, of heavy water from raw water, etc. are examples. Economical and large scale separation of isotopes particularly those of heavy elements is a task for which processess are under various stages of development. Further design of chemical plants such as fuel reprocessing plants and high level waste treatment plants, which are to be operated and maintained remotely due to the high levels of radio-activity call for engineering skills which are being continually evolved. In the reactor, analysis of the fluid mechanics and optimum design of heat removal system are other examples where a chemical engineer can play a useful role. In addition to the above, the activities in the nuclear industry cover a very wide range of chemical engineering applications, such as desalination and other energy intensive processes, radioisotope and radiation applications in industry, medicine and agriculture. (auth.)

  10. Chemical products and industrial materials

    International Nuclear Information System (INIS)

    1995-12-01

    A compilation of all universities, industrial and governmental agencies in Quebec which are actively involved in research and development of chemical products and industrial materials derived from biomass products, was presented. Each entry presented in a standard format that included a description of the major research activities of the university or agency, the principal technologies used in the research, available research and analytical equipment, a description of the research personnel, names, and addresses of contact persons for the agency or university. Thirty entries were presented. These covered a wide diversity of activities including biotechnological research such as genetic manipulations, bioconversion, fermentation, enzymatic hydrolysis and physico-chemical applications such as bleaching, de-inking, purification and synthesis. tabs

  11. Irradiation in industrial waste treatment

    Energy Technology Data Exchange (ETDEWEB)

    Perkowski, J. (Politechnika Lodzka (Poland). Katedra Chemii Radiacyjnej); Kos, L.; Rouba, J. (Research and Development Centre of the Knitting Industry, Lodz (Poland))

    1984-09-01

    In this paper, the treatment by irradiation of some surface active agents (SAA) contained in aqueous solutions and industrial wastes, has been shown. Studies were carried out on selected SAA, namely Rokafenol N-6 and Pretepon G-extra, representatives of nonionic and anionic SAA, respectively. The aqueous solutions of these compounds were irradiated in radiation chamber, at the Institute of Applied Radiation Chemistry, in Lodz Polytechnic. Co/sup 60/ was used as a source of radiation. The kinetics and degree of destruction of these compounds at the doses ranging from 2 kGy to 110 kGy were investigated. The study was extended to attempts to remove SAA from textile effluents. Reduction of other parameters of contamination, including measurements of toxicity, were also evaluated.

  12. Applying industrial symbiosis to chemical industry: A literature review

    Science.gov (United States)

    Cui, Hua; Liu, Changhao

    2017-08-01

    Chemical industry plays an important role in promoting the development of global economy and human society. However, the negative effects caused by chemical production cannot be ignored, which often leads to serious resource consumption and environmental pollution. It is essential for chemical industry to achieve a sustainable development. Industrial symbiosis is one of the key topics in the field of industrial ecology and circular economy, which has been identified as a creative path leading to sustainability. Based on an extensively searching for literatures on linking industrial symbiosis with chemical industry, this paper aims to review the literatures which involves three aspects: (1) economic and environmental benefits achieved by chemical industry through implementing industrial symbiosis, (2) chemical eco-industrial parks, (3) and safety issues for chemical industry. An outlook is also provided. This paper concludes that: (1) chemical industry can achieve both economic and environmental benefits by implementing industrial symbiosis, (2) establishing eco-industrial parks is essential for chemical industry to implement and improve industrial symbiosis, and (3) there is a close relationship between IS and safety issues of chemical industry.

  13. Chemical sensors for nuclear industry

    International Nuclear Information System (INIS)

    Gnanasekaran, K.I.

    2012-01-01

    Development of chemical sensors for detection of gases at trace levels for applications in nuclear industry will be highlighted. The sensors have to be highly sensitive, reliable and rugged with long term stability to operate in harsh industrial environment. Semiconductor and solid electrolyte based electrochemical sensors satisfy the requirements. Physico-chemical aspects underlying the development of H 2 sensors in sodium and in cover gas circuit of the Fast breeder reactors for its smooth functioning, NH 3 and H 2 S sensors for use in Heavy water production industries and NO x sensors for spent fuel reprocessing plants will be presented. Development of oxygen sensors to monitor the oxygen level in the reactor containments and sodium sensors for detection of sodium leakages will also be discussed. The talk will focus the general aspects of identification of the sensing material for the respective analyte species, development of suitable chemical route for preparing them as fine powders, the need for configuring them in thick film or thin film geometries and their performance. Pulsed laser deposition method, an elegant technique to prepare the high quality thin films of multicomponent oxides is demonstrated for preparation of nanostructured thin films of complex oxides and its use in tailoring the morphology of the complex sensing material in the desired form by optimizing the in-situ growth conditions. (author)

  14. Chemical modeling of waste sludges

    International Nuclear Information System (INIS)

    Weber, C.F.; Beahm, E.C.

    1996-10-01

    The processing of waste from underground storage tanks at the Oak Ridge National Laboratory (ORNL) and other facilities will require an understanding of the chemical interactions of the waste with process chemicals. Two aspects of sludge treatment should be well delineated and predictable: (1) the distribution of chemical species between aqueous solutions and solids, and (2) potential problems due to chemical interactions that could result in process difficulties or safety concerns. It is likely that the treatment of waste tank sludge will begin with washing, followed by basic or acidic leaching. The dissolved materials will be in a solution that has a high ionic strength where activity coefficients are far from unity. Activity coefficients are needed in order to calculate solubilities. Several techniques are available for calculating these values, and each technique has its advantages and disadvantages. The techniques adopted and described here is the Pitzer method. Like any of the methods, prudent use of this approach requires that it be applied within concentration ranges where the experimental data were fit, and its use in large systems should be preceded by evaluating subsystems. While much attention must be given to the development of activity coefficients, other factors such as coprecipitation of species and Ostwald ripening must also be considered when one aims to interpret results of sludge tests or to predict results of treatment strategies. An understanding of sludge treatment processes begins with the sludge tests themselves and proceeds to a general interpretation with the aid of modeling. One could stop with only data from the sludge tests, in which case the table of data would become an implicit model. However, this would be a perilous approach in situations where processing difficulties could be costly or result in concerns for the environment or health and safety

  15. Industrial ecology: Environmental chemistry and hazardous waste

    Energy Technology Data Exchange (ETDEWEB)

    Manahan, S.E. [Univ. of Missouri, Columbia, MO (United States). Dept. of Chemistry

    1999-01-01

    Industrial ecology may be a relatively new concept -- yet it`s already proven instrumental for solving a wide variety of problems involving pollution and hazardous waste, especially where available material resources have been limited. By treating industrial systems in a manner that parallels ecological systems in nature, industrial ecology provides a substantial addition to the technologies of environmental chemistry. Stanley E. Manahan, bestselling author of many environmental chemistry books for Lewis Publishers, now examines Industrial Ecology: Environmental Chemistry and Hazardous Waste. His study of this innovative technology uses an overall framework of industrial ecology to cover hazardous wastes from an environmental chemistry perspective. Chapters one to seven focus on how industrial ecology relates to environmental science and technology, with consideration of the anthrosphere as one of five major environmental spheres. Subsequent chapters deal specifically with hazardous substances and hazardous waste, as they relate to industrial ecology and environmental chemistry.

  16. Kraft pulping of industrial wood waste

    Science.gov (United States)

    Aziz. Ahmed; Masood. Akhtar; Gary C. Myers; Gary M. Scott

    1998-01-01

    Most of the approximately 25 to 30 million tons of industrial wood waste generated in the United States per year is burned for energy and/or landfilled. In this study, kraft pulp from industrial wood waste was evaluated and compared with softwood (loblolly pine, Douglas-fir) and hardwood (aspen) pulp. Pulp bleachability was also evaluated. Compared to loblolly pine...

  17. ASSESSMENT OF TOXICITY OF INDUSTRIAL WASTES USING CROP PLANT ASSAYS

    OpenAIRE

    Carmen Alice Teacă; Ruxanda Bodîrlău

    2008-01-01

    Environmental pollution has a harmful action on bioresources, including agricultural crops. It is generated through many industrial activities such as mining, coal burning, chemical technology, cement production, pulp and paper industry, etc. The toxicity of different industrial wastes and heavy metals excess was evaluated using crop plant assays (germination and hydroponics seedlings growth tests). Experimental data regarding the germination process of wheat (from two cultivars) and rye seed...

  18. Valorization of GaN based metal-organic chemical vapor deposition dust a semiconductor power device industry waste through mechanochemical oxidation and leaching: A sustainable green process.

    Science.gov (United States)

    Swain, Basudev; Mishra, Chinmayee; Lee, Chan Gi; Park, Kyung-Soo; Lee, Kun-Jae

    2015-07-01

    Dust generated during metal organic vapor deposition (MOCVD) process of GaN based semiconductor power device industry contains significant amounts of gallium and indium. These semiconductor power device industry wastes contain gallium as GaN and Ga0.97N0.9O0.09 is a concern for the environment which can add value through recycling. In the present study, this waste is recycled through mechanochemical oxidation and leaching. For quantitative recovery of gallium, two different mechanochemical oxidation leaching process flow sheets are proposed. In one process, first the Ga0.97N0.9O0.09 of the MOCVD dust is leached at the optimum condition. Subsequently, the leach residue is mechanochemically treated, followed by oxidative annealing and finally re-leached. In the second process, the MOCVD waste dust is mechanochemically treated, followed by oxidative annealing and finally leached. Both of these treatment processes are competitive with each other, appropriate for gallium leaching and treatment of the waste MOCVD dust. Without mechanochemical oxidation, 40.11 and 1.86 w/w% of gallium and Indium are leached using 4M HCl, 100°C and pulp density of 100 kg/m(3,) respectively. After mechanochemical oxidation, both these processes achieved 90 w/w% of gallium and 1.86 w/w% of indium leaching at their optimum condition. Copyright © 2015 Elsevier Inc. All rights reserved.

  19. The management of industrial wastes in hydrology; La gestion des dechets industriels en hydrologie

    Energy Technology Data Exchange (ETDEWEB)

    Elbaz-Seboun, V.

    1998-07-08

    The industrial wastes are made of different kind of wastes: the inert wastes, the banal wastes (municipal wastes), the special wastes containing noxious elements with respect to human health and environment, and the radioactive wastes. Each industry generates its own effluents (sludges from water treatment plants and leachates from rubbish dumps). The main water pollutions are due to the fermentescible organic matters, nitrates and heavy metals from the industrial waste waters. The aim of the public water agencies is to better protect the environment and to give help to the industrialists in the management of their wastes: reduction at the source, selective collection, valorization, transportation and processing. Non-valorizable wastes must be processed: physico-chemical and biological processing (bio-filtering, coagulation-flocculation, membranes and industrial gases), incineration (organic wastes), disposal in class 1 technical burial centres after stabilization (ultimate wastes). Since July 2002, only the ultimate wastes will be disposed off and all class 2 and 3 dumps must have been rehabilitated. This work is divided into 2 parts: part 1 gives a presentation of the different types of industrial wastes and of their management (origin of wastes, effluents, heavy metals, environmental impact, legal aspects, wastes management, valorization). The second part describes the different processes for the treatment of industrial wastes (conventional processes, physico-chemical and biological processes, incineration, tipping, processing of radioactive wastes). (J.S.)

  20. Toxicological evaluation of complex industrial wastes: Implications for exposure assessment

    Energy Technology Data Exchange (ETDEWEB)

    DeMarini, D.M.; Gallagher, J.E.; Houk, V.S.; Simmons, J.E.

    1990-07-01

    We evaluated a variety of short-term bioassays to construct a battery of tests that could be used for assessing the biological effects of potentially hazardous complex industrial wastes. Ten samples were studied for hepatotoxicity; these samples and an additional five were studied for mutagenicity. Although the data are limited to these samples, the results suggest that the Salmonella assay (strain TA98) or a prophage-induction assay (both in the presence of S9) in combination with determination of relative liver weight and levels of a set of serum enzymes in rats may provide a battery of tests suitable to characterize complex industrial wastes for mutagenic and hepatotoxic potential. The biological activities exhibited by the wastes were not readily predicted by the chemical profiles of the wastes, emphasizing the importance of characterizing potentially hazardous complex industrial wastes by both chemical and biological means. DNA from liver, lung, and bladder of rats exposed to some of the wastes was analyzed by the 32P-postlabeling technique for the presence of DNA adducts. A waste that produced mutagenic urine produced a DNA adduct in bladder DNA. The implications of this approach for assessment of exposure to complex hazardous waste mixtures are discussed.

  1. Energy from wastes and the private waste contracting industry

    International Nuclear Information System (INIS)

    Burnett, J.S.

    1993-01-01

    The focus of this ongoing work is the utilisation of general non hazardous industrial and commercial waste as an energy or fuel source. Whereas much of the existing experience in energy from waste (EFW) is related to municipal solid wastes (MSW), there is very little direct experience with these other waste streams and the shortage of reliable information in this field is notoriously lacking. It is important to have a good understanding of the private waste contracting industry (pwci) in order to establish the conditions under which energy from waste technologies may play an economically and technically feasible role within that industry's development. The Non Fossil Fuel Obligation (NFFO) has encouraged entrepreneurial interest through premium payments for electricity generated from renewable sources. (author)

  2. Solid waste management in Khartoum industrial area

    International Nuclear Information System (INIS)

    Elsidig, N. O. A.

    2004-05-01

    This study was conducted in Khartoum industrial area (KIA). The study discusses solid waste generation issues in KIA as well as solid waste collection, storage, transport and final disposal methods. A focus on environmental impact resulting from the accumulation of solid waste was presented by reviewing solid waste management in developed as well as developing countries starting from generation to final disposal. Environmental health legislation in Sudan was investigated. The study covers all the (eight) industrial sub-sectors presented in KIA. The main objective of the study is to assess the situation of solid waste in KIA. To fulfill the objectives of the study the researcher deemed it necessary to explore problems related to solid waste generation and solid waste arrangement with special emphasis on final disposal methods. Practically, 31 (thirty-one) factories representing the different industrial sub-sectors in KIA were studied. This represents 25% of the total number of factories located in KIA. Data were obtained by, questionnaires, interviews and observations mainly directed to concerned officials, solid waste workers, pickers and brokers. Obtained data were stored, coded, tabulated and analyzed using the computer systems (excel and SPSS programmes). The obtained results should clear deficiency in the management of solid waste which led to great environmental deterioration in KIA and neighboring residential areas. The environment in studied area is continuously polluted due to high pollution loads and unproved solid waste management. In order to maintain health environment operating factories have to pretreated their solid waste according to the recognized standards and waste minimization techniques such as recycling and re use should be widely applied, moreover, running crash programme for environmental sanitation in Khartoum state should be expanded and improved to include special characteristics of solid waste from industries. Finally, increase awareness

  3. System analysis of industrial waste management: A case study of industrial plants located between Tehran and Karaj

    Directory of Open Access Journals (Sweden)

    Mohammad Amin Karami

    2015-01-01

    Full Text Available Aims: In this study, management of industrial waste in industries located between Tehran and Karaj in 2009-2010 was examined. Materials and Methods: This is a cross-sectional study which was done by site survey (Iranian environmental protection organization questionnaire usage and results analysis. This questionnaire was consisted of 45 questions about industrial waste, quantity, quality, and management. A total number of industries with over 50 employees was 283, and Stratified sampling method was used. Sample of size 50 was selected from 283cases. Results: The major hazardous waste-generating industries include chemical and plastic. Private sectors disposed 45% of generated waste. Majority of wastes were buried (62%, and only 17% of industrial waste was recycled. Conclusion: For hazardous waste reduction in this zone and health and economic attractions, the opportunity for reuse and recovery for these wastes must maximize in short-term and burial of industrial waste must be minimized. Industries such as chemical-plastic and electronics which have higher hazardous waste, in long-term, must be replaced with other industries such as wood cellulose and paper that have lower hazardous waste production rate.

  4. Assessment of industrial liquid waste management in Omdurman Industrial Area

    International Nuclear Information System (INIS)

    Elnasri, R. A. A.

    2003-04-01

    This study was conducted mainly to investigate the effects of industrial liquid waste on the environment in the Omdurman area. Various types of industries are found around Omdurman. According to the ISC the major industries are divided into eight major sub-sectors, each sub-sector is divided into types of industries. Special consideration was given to the liquid waste because of its effects. In addition to the available data, personal observation supported by photographs, laboratory analyses were carried on the industrial effluents. The investigated parameters in the analysis were, BOD, COD, O and G, Cr, TDS, TSS, pH, temp and conductivity. Interviews were conducted with waste handling workers in the industries, in order to assess the effects of industrial pollution. The results obtained showed that pollutants produced by all the factories were found to exceed the accepted levels of the industrial pollution control. The effluents disposed of in the sites allotted by municipal authorities have adverse effects on the surrounding environment and public health and amenities. Accordingly the study recommends that the waste water must be pretreated before being disposed of in site allotted by municipal authorities. Develop an appropriate system for industrial waste proper management. The study established the need to construct a sewage system in the area in order to minimize the pollutants from effluents. (Author)

  5. Assessment of industrial liquid waste management in Omdurman Industrial Area

    Energy Technology Data Exchange (ETDEWEB)

    Elnasri, R A. A. [Institute of Environmental Studies, University of Khartoum, Khartoum (Sudan)

    2003-04-15

    This study was conducted mainly to investigate the effects of industrial liquid waste on the environment in the Omdurman area. Various types of industries are found around Omdurman. According to the ISC the major industries are divided into eight major sub-sectors, each sub-sector is divided into types of industries. Special consideration was given to the liquid waste because of its effects. In addition to the available data, personal observation supported by photographs, laboratory analyses were carried on the industrial effluents. The investigated parameters in the analysis were, BOD, COD, O and G, Cr, TDS, TSS, pH, temp and conductivity. Interviews were conducted with waste handling workers in the industries, in order to assess the effects of industrial pollution. The results obtained showed that pollutants produced by all the factories were found to exceed the accepted levels of the industrial pollution control. The effluents disposed of in the sites allotted by municipal authorities have adverse effects on the surrounding environment and public health and amenities. Accordingly the study recommends that the waste water must be pretreated before being disposed of in site allotted by municipal authorities. Develop an appropriate system for industrial waste proper management. The study established the need to construct a sewage system in the area in order to minimize the pollutants from effluents. (Author)

  6. Valorization of GaN based metal-organic chemical vapor deposition dust a semiconductor power device industry waste through mechanochemical oxidation and leaching: A sustainable green process

    Energy Technology Data Exchange (ETDEWEB)

    Swain, Basudev, E-mail: Swain@iae.re.kr [Institute for Advanced Engineering (IAE), Advanced Materials & Processing Center, Yongin-Si 449-863 (Korea, Republic of); Mishra, Chinmayee; Lee, Chan Gi; Park, Kyung-Soo [Institute for Advanced Engineering (IAE), Advanced Materials & Processing Center, Yongin-Si 449-863 (Korea, Republic of); Lee, Kun-Jae [Department of Energy Engineering, Dankook University, Cheonan 330-714 (Korea, Republic of)

    2015-07-15

    Dust generated during metal organic vapor deposition (MOCVD) process of GaN based semiconductor power device industry contains significant amounts of gallium and indium. These semiconductor power device industry wastes contain gallium as GaN and Ga{sub 0.97}N{sub 0.9}O{sub 0.09} is a concern for the environment which can add value through recycling. In the present study, this waste is recycled through mechanochemical oxidation and leaching. For quantitative recovery of gallium, two different mechanochemical oxidation leaching process flow sheets are proposed. In one process, first the Ga{sub 0.97}N{sub 0.9}O{sub 0.09} of the MOCVD dust is leached at the optimum condition. Subsequently, the leach residue is mechanochemically treated, followed by oxidative annealing and finally re-leached. In the second process, the MOCVD waste dust is mechanochemically treated, followed by oxidative annealing and finally leached. Both of these treatment processes are competitive with each other, appropriate for gallium leaching and treatment of the waste MOCVD dust. Without mechanochemical oxidation, 40.11 and 1.86 w/w% of gallium and Indium are leached using 4 M HCl, 100 °C and pulp density of 100 kg/m{sup 3,} respectively. After mechanochemical oxidation, both these processes achieved 90 w/w% of gallium and 1.86 w/w% of indium leaching at their optimum condition. - Highlights: • Waste MOCVD dust is treated through mechanochemical leaching. • GaN is hardly leached, and converted to NaGaO{sub 2} through ball milling and annealing. • Process for gallium recovery from waste MOCVD dust has been developed. • Thermal analysis and phase properties of GaN to Ga{sub 2}O{sub 3} and GaN to NaGaO{sub 2} is revealed. • Solid-state chemistry involved in this process is reported.

  7. A laboratory study of the effects of acid rain on industrial waste and its impact on the physico-chemical properties of groundwater

    International Nuclear Information System (INIS)

    Dehaye, J.; Badillo, M.; Zikovsky, L.

    1988-01-01

    Column experiments were used to study the leaching of 4 samples of industrial waste and 5 soil samples by distilled water and by synthetic acid rain solutions (HNO 3 and H 2 SO 4 at pH 3). The pH, the electrical conductivity, the total dissolved solids and the concentration of Al, Ca, Cl, Cr, Fe, K, Mg, Mn and Na were measured in the resulting lixiviates. The pH of the water seems to have little effect on all these parameters but they are significantly influenced by the nature of the solid material. (author) 6 refs.; 2 tabs

  8. Physio-Chemical Analysis of Industrial Effluents in parts of Edo ...

    African Journals Online (AJOL)

    Physio-Chemical Analysis of Industrial Effluents in parts of Edo States Nigeria. ... Journal of Applied Sciences and Environmental Management ... particularly, surface water results from all activities of man involving indiscriminate waste disposal from industry such as effluents into waterways, waste, agricultural waste, and all ...

  9. Chemical investigation of the effluents of selected chemical industries in NWFP (Pakistan)

    International Nuclear Information System (INIS)

    Jan, M.R.; Shah, J.; Shah, H.

    2002-01-01

    Samples of effluents were collected from the waste water drains of selected chemical industries, located at small industries estate Kohat Road Peshawar on monthly basis from November 1994 to October 1995. These samples were studied for physico chemical properties and heavy metals like Pb, Ag, Cu, Zn, Fe, Cr, Cd, Mn and Ni using spectroscopic techniques. The results of our investigation are presented and discussed. (author)

  10. An outline of the Dutch chemical industry and petrochemical industry

    International Nuclear Information System (INIS)

    Heesen, Th.J.; Terwoert, J.; Hoefnagels, F.

    1996-03-01

    An overview is given of the most important processes and products of the chemical and petrochemical industry in the Netherlands. Also attention is paid to the material balance and the energy balance of those industries. refs

  11. The future of the chemical industries

    International Nuclear Information System (INIS)

    Shinnar, R.

    1991-01-01

    As Lincoln, we first must ask where we are before we ask whither. I'd therefore like to define where our industry is and how it got there before we look at the challenges facing us. If we view the chemical and petroleum industries through the glass of macroeconomics, they look very healthy. Let's start with size. Table 1 shows that these two industries each provide about 10% of the total U.S. manufacturing output. This paper shows the fraction of the total GNP contributed by the chemical industry and by the petroleum industry and compares them with total manufacturing. The authors note that total manufacturing grew more slowly than the total GNP, whereas over the last 40 years, the chemical industry grew close to the rate of the GNP. For a large industry, this is the best we can hope for. The chemical industry is one of the very few major industries that has consistently maintained a positive trade balance

  12. Chemical and mineralogical characterization of waste generated in the petroleum industry and its correlation with 226Ra and 228Ra contents

    International Nuclear Information System (INIS)

    Gazineu, M.H.P.; Hazin, C.H.; Godoy, J.M.O.

    2004-01-01

    Scales and sludge are commonly formed during oil and gas extracting and processing operations. They usually appear when injection and formation water with different chemical characteristics come into contact. When the produced water is brought to the surface alongside with the oil, the precipitate can be deposited on the walls of tubing and equipment, forming the so-called scales. Otherwise they can also accumulate in the form of sludge on the bottom of storage tanks, separators, and other equipment. Radium is the main radionuclide brought to the surface with oil and produced water and it co-precipitates with barium forming complex compounds of sulfates, carbonates and silicates. These compounds are the main constituents of scale and sludge. The objective of this work was to relate the radium content of scales and sludge to their chemical and mineralogical composition. Samples were taken from a PETROBRAS unit in the State of Sergipe, in Northeast Brazil. They were collected either from the inner surface of water pipes or from containers stored in the waste storage area of the unit. Oil was separated from the solid material in a Soxhlet extractor equipment by using aguarras as solvent. The concentrations of 226 Ra and 228 Ra were determined by gamma spectrometry. The mineralogical and the chemical composition of the samples were determined by x-ray diffraction and x-ray fluorescence, respectively, and used to characterize the samples as scales or sludge. The results have shown that scales are mainly formed by BaSO 4 and CaCO 3 while sludge has a higher content of SiO 2 and FeO 3 than that observed on the scale samples. The measured activity concentrations of 226 Ra and 228 Ra are strongly correlated for both kinds of samples. Based on the 228 Th/ 228 Ra ratio, ages between one and five years were estimated for the material stored in the waste area. (author)

  13. Guide for Industrial Waste Management

    Science.gov (United States)

    The purpose of the Guide is to provide facility managers, state and tribal regulators, and the interested public with recommendations and tools to better address the management of land-disposed, non-hazardousindustrial wastes.

  14. Industrial Water Waste, Problems and the Solution

    Directory of Open Access Journals (Sweden)

    Alif Noor Anna

    2004-01-01

    Full Text Available Recently, the long term development in Indonesia has changed agricultural sector to the industrial sector. This development can apparently harm our own people. This is due to the waste that is produced from factories. The waste from various factories seems to have different characteristics. This defference encourages us to be able to find out different of methods of managing waste so that cost can be reduced, especially in water treatment. In order that industrial development and environmental preservation can run together in balance, many institutions involved should be consider, especially in the industrial chain, the environment, and human resource, these three elements can be examined in terms of their tolerance to waste.

  15. Renewable energy recovery through selected industrial wastes

    Science.gov (United States)

    Zhang, Pengchong

    Typically, industrial waste treatment costs a large amount of capital, and creates environmental concerns as well. A sound alternative for treating these industrial wastes is anaerobic digestion. This technique reduces environmental pollution, and recovers renewable energy from the organic fraction of those selected industrial wastes, mostly in the form of biogas (methane). By applying anaerobic technique, selected industrial wastes could be converted from cash negative materials into economic energy feed stocks. In this study, three kinds of industrial wastes (paper mill wastes, brown grease, and corn-ethanol thin stillage) were selected, their performance in the anaerobic digestion system was studied and their applicability was investigated as well. A pilot-scale system, including anaerobic section (homogenization, pre-digestion, and anaerobic digestion) and aerobic section (activated sludge) was applied to the selected waste streams. The investigation of selected waste streams was in a gradually progressive order. For paper mill effluents, since those effluents contain a large amount of recalcitrant or toxic compounds, the anaerobic-aerobic system was used to check its treatability, including organic removal efficiency, substrate utilization rate, and methane yield. The results showed the selected effluents were anaerobically treatable. For brown grease, as it is already well known as a treatable substrate, a high rate anaerobic digester were applied to check the economic effect of this substrate, including methane yield and substrate utilization rate. These data from pilot-scale experiment have the potential to be applied to full-scale plant. For thin stillage, anaerobic digestion system has been incorporated to the traditional ethanol making process as a gate-to-gate process. The performance of anaerobic digester was applied to the gate-to-gate life-cycle analysis to estimate the energy saving and industrial cost saving in a typical ethanol plant.

  16. Glass-ceramics with multibarrier structure obtained from industrial waste

    Energy Technology Data Exchange (ETDEWEB)

    Berzina, L.; Cimdins, R.; Rozenstrauha, I. [Riga Tech. Univ. (Latvia). Fac. of Chem. Technol.; Bossert, J. [Technisches Inst.: Materialwissenschaft, Friedrich-Schiller-Univ., Jena (Germany); Kravtchenko, I. [Inst. for Problems of Material Science, Kiev (Ukraine)

    1997-12-31

    Recycling problem for various kind of waste is solved by processing the waste to ecological depositable products with multibarrier structure. In order to form a multibarrier structure the ecologically incompatible substances may be diluted and chemically bound until their recycling products gain a structure like natural mineral or glass (I. barrier). After that, remineralized materials are converted into a new product by melting or powder technology using an ecological compatible type of waste as a matrix phase (II. barrier). Waste which are treated this way could be applied to produce ceramic building materials and goods such as floor tiles, stone pavement and casting products. Industrial waste from the metallurgical factory in Latvia ``Liepajas metalurgs`` are metallurgical slag, filter dust, etching waste and sewage used in technologies. The main constituents of chemical compositions of these waste are: Fe, Ca, Si, Mg, Al, Mn etc. In some types of waste a small amount of ecologically risky elements such as Cr, Ni, Zr, Sn and Pb can occur. The combination of metallurgical waste with peat ashes from Riga thermal power station, oil shale ashes or glass waste under controlled sintering procedure gives bulk materials with surface or/and bulkcrystallization. The structure of glass-ceramics built this way may prevent the migration of ecologically risky elements into environment due to corrosion or friction. Physical-chemical properties and thermal behaviour (DTA, dilatometry, melting) of waste define the range of sintering for production of glass-ceramics (powder technology) and decorative glass-ceramic materials (melting and powder technology). (orig.) 5 refs.

  17. Industrial chemical exposure: guidelines for biological monitoring

    National Research Council Canada - National Science Library

    Lauwerys, Robert R; Hoet, Perrine

    2001-01-01

    .... With Third Edition of Industrial Chemical Exposure you will understand the objectives of biological monitoring, the types of biological monitoring methods, their advantages and limitations, as well...

  18. Industrial Waste Landfill IV upgrade package

    International Nuclear Information System (INIS)

    1994-01-01

    The Y-12 Plant, K-25 Site, and ORNL are managed by DOE's Operating Contractor (OC), Martin Marietta Energy Systems, Inc. (Energy Systems) for DOE. Operation associated with the facilities by the Operating Contractor and subcontractors, DOE contractors and the DOE Federal Building result in the generation of industrial solid wastes as well as construction/demolition wastes. Due to the waste streams mentioned, the Y-12 Industrial Waste Landfill IV (IWLF-IV) was developed for the disposal of solid industrial waste in accordance to Rule 1200-1-7, Regulations Governing Solid Waste Processing and Disposal in Tennessee. This revised operating document is a part of a request for modification to the existing Y-12 IWLF-IV to comply with revised regulation (Rule Chapters 1200-1-7-.01 through 1200-1-7-.08) in order to provide future disposal space for the ORR, Subcontractors, and the DOE Federal Building. This revised operating manual also reflects approved modifications that have been made over the years since the original landfill permit approval. The drawings referred to in this manual are included in Drawings section of the package. IWLF-IV is a Tennessee Department of Environmental and Conservation/Division of Solid Waste Management (TDEC/DSWM) Class 11 disposal unit

  19. Chemical decontamination method for radioactive metal waste

    International Nuclear Information System (INIS)

    Onuma, Tsutomu; Akimoto, Hidetoshi

    1991-01-01

    The invention relates to a decontamination method for radioactive metal waste products derived from equipment that handles radioactive materials whose surfaces have been contaminated; in particular it concerns a decontamination method that reduces the amount of radioactive waste by decontaminating radioactive waste substances to a level of radioactivity in line with normal waste products. In order to apply chemical decontamination to metal waste products whose surfaces are divided into carbon steel waste and stainless steel waste; the carbon steel waste is treated using only a primary process in which the waste is immersed in a sulfuric acid solution, while the stainless steel waste must be treated with both the primary process and then electrolytically reduces it for a specific length of time and a secondary process that uses a solution of sulfuric acid mixed with oxidizing metal salts. The method used to categorize metal waste into carbon steel waste and stainless steel waste involves determining the presence, or absence, of magnetism. Voltage is applied for a fixed duration; once that has stopped, electrolytic reduction repeats the operative cycle of applying, then stopping voltage until the potential of the radioactive metal waste is retained in the active region. 1 fig. 2 tabs

  20. Economic Aspects of the Chemical Industry

    Science.gov (United States)

    Koleske, Joseph V.

    Within the formal disciplines of science at traditional universities, through the years, chemistry has grown to have a unique status because of its close correspondence with an industry and with a branch of engineering—the chemical industry and chemical engineering. There is no biology industry, but aspects of biology have closely related disciplines such as fish raising and other aquaculture, animal cloning and other facets of agriculture, ethical drugs of pharmaceutical manufacture, genomics, water quality and conservation, and the like. Although there is no physics industry, there are power generation, electricity, computers, optics, magnetic media, and electronics that exist as industries. However, in the case of chemistry, there is a named industry. This unusual correspondence no doubt came about because in the chemical industry one makes things from raw materials—chemicals—and the science, manufacture, and use of chemicals grew up together during the past century or so.

  1. Education-industry partnership: the chemical industry experience

    International Nuclear Information System (INIS)

    Bricknell, D.J.

    1994-01-01

    The European Chemical Industry and the Nuclear Power Industry share similar problems and hopefully can share similar solutions to them. A recent survey of public opinion conducted on behalf of the chemical industry has shown that the general public knows little about the industry and does not trust it to behave responsibly. The industry is responding in two ways: firstly to demonstrate that it is a responsible member of the community by operating to the highest safety and environmental standards and by being open in its dealings with the public on such matters. Secondly the industry is working with the education system to ensure that the public has the opportunity to gain a good education in science, is able to make rational judgments about risks and benefits and is better able to understand and accept the role of the chemical industry in society

  2. Animal and industrial waste anaerobic digestion: USA status report

    Energy Technology Data Exchange (ETDEWEB)

    Lusk, P.D. [Resource Development Associates, Washington, DC (United States)

    1996-01-01

    Pollutants from unmanaged animal and bio-based industrial wastes can degrade the environment, and methane emitted from decomposing wastes may contribute to global climate change. One waste management system prevents pollution and converts a disposal problem into a new profit center. Case studies of operating systems indicate that the anaerobic digestion of animal and industrial wastes is a commercially available bioconversion technology with considerable potential for providing profitable coproducts, including a cost-effective renewable fuel. Growth and concentration of the livestock industry create opportunities to properly dispose of the large quantities of manures generated at dairy, swine, and poultry farms. Beyond the farm, extension of the anaerobic digestion process to recover methane has considerable potential for certain classified industries - with a waste stream characterization similar to livestock manures. More than 35 example industries have been identified, and include processors of chemicals, fiber, food, meat, milk, and pharmaceuticals. Some of these industries already recover methane for energy. This status report examines some current opportunities for recovering methane from the anaerobic digestion of animal and industrial wastes in the US. Case studies of operating digesters, including project and maintenance histories, and the operator`s {open_quotes}lessons learned,{close_quotes} are included as a reality check. Factors necessary for successful projects, as well as a list of reasons explaining why some anaerobic digestion projects fail, are provided. The role of management is key; not only must digesters be well engineered and built with high-quality components, they must also be sited at facilities willing to incorporate the uncertainties of a new technology. Anaerobic digestion can provide monetary benefits and mitigate possible pollution problems, thereby sustaining development while maintaining environmental quality.

  3. Exergetic comparison of food waste valorization in industrial bread production

    International Nuclear Information System (INIS)

    Zisopoulos, Filippos K.; Moejes, Sanne N.; Rossier-Miranda, Francisco J.; Goot, Atze Jan van der; Boom, Remko M.

    2015-01-01

    This study compares the thermodynamic performance of three industrial bread production chains: one that generates food waste, one that avoids food waste generation, and one that reworks food waste to produce new bread. The chemical exergy flows were found to be much larger than the physical exergy consumed in all the industrial bread chains studied. The par-baked brown bun production chain had the best thermodynamic performance because of the highest rational exergetic efficiency (71.2%), the lowest specific exergy losses (5.4 MJ/kg brown bun), and the almost lowest cumulative exergy losses (4768 MJ/1000 kg of dough processed). However, recycling of bread waste is also exergetically efficient when the total fermented surplus is utilizable. Clearly, preventing material losses (i.e. utilizing raw materials maximally) improves the exergetic efficiency of industrial bread chains. In addition, most of the physical (non-material related) exergy losses occurred at the baking, cooling and freezing steps. Consequently, any additional improvement in industrial bread production should focus on the design of thermodynamically efficient baking and cooling processes, and on the use of technologies throughout the chain that consume the lowest possible physical exergy. - Highlights: • Preventing material losses is the best way to enhance the exergetic efficiency. • Most of the physical exergy losses occur at the baking, cooling and freezing steps. • Par-baking “saves” chemical exergy but consumes an equal amount of physical exergy

  4. An essay on: management of industrial waste, an engineer's viewpoint

    International Nuclear Information System (INIS)

    Raphael, M.A.

    1995-01-01

    Industrial waste and industrial waste management are described, with economic considerations and recommendations for an industrial waste management program applicable in Lebanon. Different conceptual systems for industrial waste management are presented: - The O effluent industrial plant, an electric manufacturing plant with mass and energy balance. - The industrial complexing concept where environmentally balanced and compatible, industries are located in one area. Waste effluents from one plant can be used as raw material for another plant. - A standard petroleum waste recovery plant to cope with local requirements complementary to the proposed sanitary waste treatment plant in Lebanon. Major sources of industrial waste in Lebanon are analyzed:local process industries, hospitals, laboratories, petroleum industries and power generation, are the major sources cited. For each source the level of treatment is indicated. Tables and appendixes on waste treatment and management along with the ISO 9000 series are presented. 10 refs. 3 figs

  5. Control in the Chemical Industry

    Science.gov (United States)

    Jones, R. G.

    1974-01-01

    Discusses various control techniques used in chemical processes, including measuring devices, controller functions, control valves, and feedforward and feedback actions. Applications of control to a real chemical plant are exemplified. (CC)

  6. Chemical risks from nuclear waste repositories

    International Nuclear Information System (INIS)

    Persson, L.

    1988-01-01

    Studies concerning the chemical risks of nuclear waste are reviewed. The radiological toxicity of the material is of primary concern but the potential nonradiological toxicity should not be overlooked as the chemotoxic substances may reach the biosphere from a nuclear waste repository. In the report is concluded that the possible chemotoxic effects of a repository for nuclear waste should be studied as a part of the formal risk assessment of the disposal concept. (author)

  7. Hazardous chemical and radioactive wastes at Hanford

    International Nuclear Information System (INIS)

    Keller, J.F.; Stewart, T.L.

    1991-07-01

    The Hanford Site was established in 1944 to produce plutonium for defense. During the past four decades, a number of reactors, processing facilities, and waste management facilities have been built at Hanford for plutonium production. Generally, Hanford's 100 Area was dedicated to reactor operation; the 200 Area to fuel reprocessing, plutonium recovery, and waste management; and the 300 Area to fuel fabrication and research and development. Wastes generated from these operations included highly radioactive liquid wastes, which were discharged to single- and double-shell tanks; solid wastes, including both transuranic (TRU) and low-level wastes, which were buried or discharged to caissons; and waste water containing low- to intermediate-level radioactivity, which was discharged to the soil column via near-surface liquid disposal units such as cribs, ponds, and retention basins. Virtually all of the wastes contained hazardous chemical as well as radioactive constituents. This paper will focus on the hazardous chemical components of the radioactive mixed waste generated by plutonium production at Hanford. The processes, chemicals used, methods of disposition, fate in the environment, and actions being taken to clean up this legacy are described by location

  8. Hazardous chemical and radioactive wastes at Hanford

    International Nuclear Information System (INIS)

    Keller, J.F.; Stewart, T.L.

    1993-01-01

    The Hanford Site was established in 1944 to produce plutonium for defense. During the past four decades, a number of reactors, processing facilities, and waste management facilities were built at Hanford for plutonium production. Generally, Hanford's 100 Area was dedicated to reactor operation; the 200 Areas to fuel reprocessing, plutonium recovery, and waste management; and the 300 Area to fuel fabrication and research and development. Wastes generated from these operations included highly radioactive liquid wastes, which were discharged to single- and double-shell tanks; solid wastes, including both transuranic and low-level wastes, which were buried or discharged to caissons; and waste water containing low- to intermediate-level radioactivity, which was discharged to the soil column via near-surface liquid disposal units such as cribs, ponds, and retention basins. Virtually all of the wastes contained hazardous chemicals as well as radioactive constituents. This paper focuses on the hazardous chemical components of the radioactive mixed waste generated by plutonium production at Hanford. The processes, chemicals used, methods of disposition, fate in the environment, and actions being taken to clean up this legacy are described by location

  9. Waste Material Management: Energy and materials for industry

    Energy Technology Data Exchange (ETDEWEB)

    1993-05-01

    This booklet describes DOE`s Waste Material Management (WMM) programs, which are designed to help tap the potential of waste materials. Four programs are described in general terms: Industrial Waste Reduction, Waste Utilization and Conversion, Energy from Municipal Waste, and Solar Industrial Applications.

  10. Hazardous Waste Cleanup: Chemical Waste Management of NJ in Newark, New Jersey

    Science.gov (United States)

    Chemical Waste Management of NJ is located at 100 Lister Avenue in Newark, New Jersey. This section of Newark has been industrial since the late 1800s when the marshlands of the Passaic River were filled in with a mixture of coal ash, construction debris

  11. Characterization of low-level waste from the industrial sector, and near-term projection of waste volumes and types

    International Nuclear Information System (INIS)

    MacKenzie, D.R.

    1988-01-01

    A telephone survey of low-level waste generators has been carried out in order to make useful estimates of the volume and nature of the waste which the generators will be shipping for disposal when the compacts and states begin operating new disposal facilities. Emphasis of the survey was on the industrial sector, since there has been little information available on characteristics of industrial LLW. Ten large industrial generators shipping to Richland, ten shipping to Barnwell, and two whose wastes had previously been characterized by BNL were contacted. The waste volume shipped by these generators accounted for about two-thirds to three-quarters of the total industrial volume. Results are given in terms of the categories of LLW represented and of the chemical characteristics of the different wastes. Estimates by the respondents of their near-term waste volume projections are presented

  12. Characterization of low-level waste from the industrial sector, and near-term projection of waste volumes and types

    International Nuclear Information System (INIS)

    MacKenzie, D.R.

    1988-01-01

    A telephone survey of low-level waste generators has been carried out in order to make useful estimates of the volume and nature of the waste which the generators are shipping for disposal when the compacts and states begin operating new disposal facilities. Emphasis of the survey was on the industrial sector, since there has been little information available on characteristics of industrial LLW. Ten large industrial generators shipping to Richland, ten shipping to Barnwell, and two whose wastes had previously been characterized by BNL were contacted. The waste volume shipped by these generators accounted for about two-thirds to three-quarters of the total industrial volume. Results are given in terms of the categories of LLW represented and of the chemical characteristics of the different wastes. Estimates by the respondents of their near-term waste volume projections are presented

  13. Clearance level and industrial waste management

    International Nuclear Information System (INIS)

    Asano, Toichi

    1999-01-01

    Defining the clearance level enables the radioactive waste with lower radioactivity than a certain level to be the general industrial waste and therefore consideration for public acceptance is essential. For this, it is necessary to understand laws concerning not only atomic power and radioactivity but also disposal and cleaning of general waste. It is also necessary that the waste below the clearance level should be as much as possible handled in the modern common concept of recycling of resources. In 1996, the weight of industrial waste was about 400 million tons, of which 40% was disposed by burning and dehydration, 39% was re-used and 21% was subjected to the final disposal like reclamation. Reduction, re-use and recycling of the generated waste are required for making the society with recycling of resources. Scrap concrete materials below the clearance level of 0.6 million tons are estimated to be generated by dismantling the light water reactor of 1 million kW output and profitable technology for recycling the scrap is under investigation. (K.H.)

  14. An Assessment of Radioactivity of Selected Industrial Waste

    International Nuclear Information System (INIS)

    Huwait, M. A.; ElMongy, S.A.; Abdo, A.A.A.; Hassan, M.H.

    1999-01-01

    phosphogypsum (phph) is a by-product in the manufacture of phosphoric acid for the artificial fertilizer industry. In the present work, qualitative and quantitative radioactive analysis are carried for phph of National Company of Abuzabal for chemical fertilizers. Gamma ray spectroscopy techniques are applied. The present study reveals that the radioactivity resulted from these wastes is out of the international standards, and it is strongly not recommended to be used as a construction material or for dwellings

  15. Industrial Waste Landfill IV upgrade package

    International Nuclear Information System (INIS)

    1994-01-01

    This document consists of page replacements for the Y-12 industrial waste landfill. The cover page is to replace the old page, and a new set of text pages are to replace the old ones. A replacement design drawing is also included

  16. International Trade of Croatian Chemical Industry Summary

    Directory of Open Access Journals (Sweden)

    Goran Buturac

    2009-07-01

    Full Text Available In this paper Croatian chemical industry in international trade is analyzed by applying k-means cluster method. The work is oriented toward the role and contribution of individual product groups in total trade patterns of chemical industry. The RCA indicator, GL index, RUV indicator and the share of individual chemical products in the total export of chemical industry are used as variables. The products at the fourdigit level of the SITC are used as objects. The cluster of chemical products in which Croatia has comparative advantages contributes significantly in export structure. At the same time this cluster consists of a few product types thus indicating strong export concentration of Croatian chemical industry. Regarding of the value of RUV indicator, Croatian chemical industry benefits most in the international trade with antibiotics and medicines that contain antibiotics. Beside fertilizers, these two products have the greatest share in the export structure. The great majority of the chemical products have the low level of intra-industry trade specialization.

  17. Acoustic barriers obtained from industrial wastes.

    Science.gov (United States)

    Garcia-Valles, M; Avila, G; Martinez, S; Terradas, R; Nogués, J M

    2008-07-01

    Acoustic pollution is an environmental problem that is becoming increasingly more important in our society. Likewise, the accumulation of generated waste and the need for waste management are also becoming more and more pressing. In this study we describe a new material--called PROUSO--obtained from industrial wastes. PROUSO has a variety of commercial and engineering, as well as building, applications. The main raw materials used for this environmentally friendly material come from slag from the aluminium recycling process, dust from the marble industry, foundry sands, and recycled expanded polystyrene from recycled packaging. Some natural materials, such as plastic clays, are also used. To obtain PROUSO we used a conventional ceramic process, forming new mineral phases and incorporating polluted elements into the structure. Its physical properties make PROUSO an excellent acoustic and thermal insulation material. It absorbs 95% of the sound in the frequency band of the 500 Hz. Its compressive strength makes it ideal for use in ceramic wall building.

  18. Hazard ranking systems for chemical wastes and chemical waste sites

    International Nuclear Information System (INIS)

    Waters, R.D.; Parker, F.L.; Crutcher, M.R.

    1991-01-01

    Hazardous materials and substances have always existed in the environment. Mankind has evolved to live with some degree of exposure to toxic materials. Until recently the risk has been from natural toxins or natural background radiation. While rapid technological advances over the past few decades have improved the lifestyle of our society, they have also dramatically increased the availability, volume and types of synthetic and natural hazardous materials. Many of their effects are as yet uncertain. Products and manufacturing by-products that no longer serve a useful purpose are deemed wastes. For some waste products land disposal will always be their ultimate fate. Hazardous substances are often included in the waste products. One needs to classify wastes by degree of hazard (risk). Risk (degree of probability of loss) is usually defined for risk assessment as probability of an occurrence times the consequences of the occurrence. Perhaps even more important than the definition of risk is the choice of a risk management strategy. The choice of strategy will be strongly influenced by the decision criteria used. Those decision criteria could be utility (the greatest happiness of the greatest number), rights or technology based or some combination of the three. It is necessary to make such choices about the definition of risks and criteria for management. It is clear that these are social (i.e., political) and value choices and science has little to say on this matter. This is another example of what Alvin Weinberg has named Transcience where the subject matter is scientific and technical but the choices are social, political and moral. This paper shall deal only with the scientific and technical aspects of the hazardous waste problem to create a hazardous substances classification system

  19. Transformation Leadership in Chemical Industry

    KAUST Repository

    Alsherehy, Fahad A.

    2018-01-16

    SABIC is a global leader in diversified chemicals headquartered in Riyadh, Saudi Arabia. It manufactures on a global scale in the Americas, Europe, Middle East and Asia Pacific, making distinctly different kinds of products: chemicals, commodity and high performance plastics, agri-nutrients and metals. The company has more than 35,000 employees worldwide and operates in more than 50 countries, with innovation hubs in five key geographies ヨ USA, Europe, Middle East, South East Asia and North East Asia.

  20. Transformation Leadership in Chemical Industry

    KAUST Repository

    Alsherehy, Fahad A.

    2018-01-01

    SABIC is a global leader in diversified chemicals headquartered in Riyadh, Saudi Arabia. It manufactures on a global scale in the Americas, Europe, Middle East and Asia Pacific, making distinctly different kinds of products: chemicals, commodity and high performance plastics, agri-nutrients and metals. The company has more than 35,000 employees worldwide and operates in more than 50 countries, with innovation hubs in five key geographies ヨ USA, Europe, Middle East, South East Asia and North East Asia.

  1. Thermal desorption-gas chromatography-mass spectrometry methods and strategy for screening of chemical warfare agents, their precursors and degradation products in environmental, industrial and waste samples

    NARCIS (Netherlands)

    Terzic, O.

    2016-01-01

    The Organisation for the Prohibition of Chemical Weapons (OPCW) is the international organisation set to oversee the implementation of the Chemical Weapons Convention treaty that prohibits the development, production, acquisition, stockpiling, retention, transfer or use of chemical weapons by States

  2. Chemical aspects of nuclear waste treatment

    International Nuclear Information System (INIS)

    Bond, W.D.

    1980-01-01

    The chemical aspects of the treatment of gaseous, liquid, and solid wastes are discussed in overview. The role of chemistry and the chemical reactions in waste treatment are emphasized. Waste treatment methods encompass the chemistry of radioactive elements from every group of the periodic table. In most streams, the radioactive elements are present in relatively low concentrations and are often associated with moderately large amounts of process reagents, or materials. In general, it is desirable that waste treatment methods are based on chemistry that is selective for the concentration of radionuclides and does not require the addition of reagents that contribute significantly to the volume of the treated waste. Solvent extraction, ion exchange, and sorbent chemistry play a major role in waste treatment because of the high selectivity provided for many radionuclides. This paper deals with the chemistry of the onsite treatment methods that is typically used at nuclear installations and is not concerned with the chemistry of the various alternative materials proposed for long-term storage of nuclear wastes. The chemical aspects are discussed from a generic point of view in which the chemistry of important radionuclides is emphasized

  3. Bio-electrochemical system (BES) as an innovative approach for sustainable waste management in petroleum industry.

    Science.gov (United States)

    Srikanth, Sandipam; Kumar, Manoj; Puri, S K

    2018-02-15

    Petroleum industry is one of the largest and fast growing industries due to the ever increasing global energy demands. Petroleum refinery produces huge quantities of wastes like oily sludge, wastewater, volatile organic compounds, waste catalyst, heavy metals, etc., because of its high capacity and continuous operation of many units. Major challenge to this industry is to manage the huge quantities of waste generated from different processes due to the complexity of waste as well as changing stringent environmental regulations. To decrease the energy loss for treatment and also to conserve the energy stored in the chemical bonds of these waste organics, bio-electrochemical system (BES) may be an efficient tool that reduce the economics of waste disposal by transforming the waste into energy pool. The present review discusses about the feasibility of using BES as a potential option for harnessing energy from different waste generated from petroleum refineries. Copyright © 2018. Published by Elsevier Ltd.

  4. Waste processing of chemical cleaning solutions

    International Nuclear Information System (INIS)

    Peters, G.A.

    1991-01-01

    This paper reports on chemical cleaning solutions containing high concentrations of organic chelating wastes that are difficult to reduce in volume using existing technology. Current methods for evaporating low-level radiative waste solutions often use high maintenance evaporators that can be costly and inefficient. The heat transfer surfaces of these evaporators are easily fouled, and their maintenance requires a significant labor investment. To address the volume reduction of spent, low-level radioactive, chelating-based chemical cleaning solutions, ECOSAFE Liquid Volume Reduction System (LVRS) has been developed. The LVRS is based on submerged combustion evaporator technology that was modified for treatment of low-level radiative liquid wastes. This system was developed in 1988 and was used to process 180,000 gallons of waste at Oconee Nuclear Station

  5. Instructive of chemical residues waste administration

    International Nuclear Information System (INIS)

    Alfaro Vargas, Ariel

    2014-01-01

    An instructive is established for the waste management system of chemical residues generated at the Universidad de Costa Rica, ensuring the collection, separation, transportation, reuse, recycling and final disposal. The laboratory waste management system is conditioned to the volume and type of waste generated. The respective procedures are listed in data sheets according to the corresponding model: avoid, reduce, recycle, treat, delete. The materials are identified as: expired products, materials or damaged products, substances that have lost some of the required characteristics, waste from the regular activities of the lab, unused products that now no longer used because they are considered inadequate. The chemicals reagents or hazardous are transformed into small amounts of derivatives safe products, or less hazardous, to allow for removal or to pick up a spill of these without problem [es

  6. Chemical decontamination method for radioactive metal waste

    International Nuclear Information System (INIS)

    Onuma, Tsutomu; Tanaka, Akio; Shibuya, Sadao.

    1991-01-01

    When contaminants mainly composed of copper remained on the surface of stainless steel wastes sent from an electrolytic reduction as a first step are chemically decontaminated, metal wastes are discriminated to carbon steel wastes and stainless steel wastes. Then, the carbon steel wastes are applied only with the first step of immersing in a sulfuric acid solution, and stainless steel wastes are applied with a first step of immersing into a sulfuric acid solution for electrolytic reduction for a predetermined period of time and a second step of immersing into a liquid in which an oxidative metal salt is added to sulfuric acid. The decontamination liquid which is used for immersing the stainless steel wastes in the second step and the oxidation force of which is lowered is used as the sulfuric acid solution in the first step for the carbon steel wastes. In view of the above, the decontamination liquid of the second step can be utilized most effectively, enabling to greatly decrease the secondary wastes and to improve decontamination efficiency. (T.M.)

  7. Geohydrology of industrial waste disposal site

    International Nuclear Information System (INIS)

    Gaynor, R.K.

    1984-01-01

    An existing desert site for hazardous chemical and low-level radioactive waste disposal is evaluated for suitability. This site is characterized using geologic, geohydrologic, geochemical, and other considerations. Design and operation of the disposal facility is considered. Site characteristics are also evaluated with respect to new and proposed regulatory requirements under the Resource Conservation and Recovery Act (1976) regulations, 40 CFR Part 264, and the ''Licensing Requirements for Landfill Disposal of Radioactive Waste,'' 10 CRF Part 61. The advantages and disadvantages of siting new disposal facilities in similar desert areas are reviewed and contrasted to siting in humid locations

  8. Beyond petrochemicals: The renewable chemicals industry

    DEFF Research Database (Denmark)

    Vennestrøm, P.N.R.; Osmundsen, Christian Mårup; Christensen, C.H.

    2011-01-01

    From petroleum to bioleum: Since biomass is a limited resource, it is necessary to consider its best use. The production of select chemicals from biomass, rather than its use as fuel, could effectively replace the use of petroleum in the chemical industry, but the inherent functionality of biomas...

  9. Job Relocation is High in Chemical Industry.

    Science.gov (United States)

    Chemical and Engineering News, 1979

    1979-01-01

    The chances of an employee being relocated are higher in the chemical and plastics industries than in U.S. business as a whole. But the benefits provided by chemical and plastics companies to employees shifted to other locations are generally better than average. (Author/BB)

  10. The modern alchemy: The chemical industry

    International Nuclear Information System (INIS)

    Valencia Giraldo, Asdrubal

    2002-01-01

    A brief history is presented on the development of chemistry from the antiquity, through alchemy, iatrochemistry, electrochemistry, atomic theory and the XVII, XVIII, XIX and X X centuries discoveries up to modern chemistry, fine chemistry, chemical engineering and the modern chemical industry with all of its consequences

  11. Chemical compatibility of DWPF canistered waste forms

    International Nuclear Information System (INIS)

    Harbour, J.R.

    1993-01-01

    The Waste Acceptance Preliminary Specifications (WAPS) require that the contents of the canistered waste form are compatible with one another and the stainless steel canister. The canistered waste form is a closed system comprised of a stainless steel vessel containing waste glass, air, and condensate. This system will experience a radiation field and an elevated temperature due to radionuclide decay. This report discusses possible chemical reactions, radiation interactions, and corrosive reactions within this system both under normal storage conditions and after exposure to temperatures up to the normal glass transition temperature, which for DWPF waste glass will be between 440 and 460 degrees C. Specific conclusions regarding reactions and corrosion are provided. This document is based on the assumption that the period of interim storage prior to packaging at the federal repository may be as long as 50 years

  12. A Study on the Evaluation of Industrial Solid Waste Management ...

    African Journals Online (AJOL)

    Industrial solid waste is a serious health concern in Aba, South East Nigeria. This study was undertaken to assess the approaches of some industries toward some aspects of waste management in Aba. Interviews, observation and questionnaires administered to industry executives and waste managers were used to ...

  13. Chemical and Biological Catalytic Enhancement of Weathering of Silicate Minerals and industrial wastes as a Novel Carbon Capture and Storage Technology

    Science.gov (United States)

    Park, A. H. A.

    2014-12-01

    Increasing concentration of CO2 in the atmosphere is attributed to rising consumption of fossil fuels around the world. The development of solutions to reduce CO2 emissions to the atmosphere is one of the most urgent needs of today's society. One of the most stable and long-term solutions for storing CO2 is via carbon mineralization, where minerals containing metal oxides of Ca or Mg are reacted with CO2 to produce thermodynamically stable Ca- and Mg-carbonates that are insoluble in water. Carbon mineralization can be carried out in-situ or ex-situ. In the case of in-situ mineralization, the degree of carbonation is thought to be limited by both mineral dissolution and carbonate precipitation reaction kinetics, and must be well understood to predict the ultimate fate of CO2 within geological reservoirs. While the kinetics of in-situ mineral trapping via carbonation is naturally slow, it can be enhanced at high temperature and high partial pressure of CO2. The addition of weak organic acids produced from food waste has also been shown to enhance mineral weathering kinetics. In the case of the ex-situ carbon mineralization, the role of these ligand-bearing organic acids can be further amplified for silicate mineral dissolution. Unfortunately, high mineral dissolution rates often lead to the formation of a silica-rich passivation layer on the surface of silicate minerals. Thus, the use of novel solvent mixture that allows chemically catalyzed removal of this passivation layer during enhanced Mg-leaching surface reaction has been proposed and demonstrated. Furthermore, an engineered biological catalyst, carbonic anhydrase, has been developed and evaluated to accelerate the hydration of CO2, which is another potentially rate-limiting step of the carbonation reaction. The development of these novel catalytic reaction schemes has significantly improved the overall efficiency and sustainability of in-situ and ex-situ mineral carbonation technologies and allowed direct

  14. Methanization of domestic and industrial wastes

    International Nuclear Information System (INIS)

    2011-01-01

    After having recalled that methanization helps meeting objectives of the Grenelle de l'Environnement regarding waste valorisation and production of renewable heat and electricity, this publication presents the methanization process which produces a humid product (digestate) and biogas by using various wastes (from agriculture, food industry, cities, households, sludge and so on). The numbers of existing and planned methanization units are evoked. The publication discusses the main benefits (production of renewable energy, efficient waste processing, and compact installations), drawbacks (costs, necessary specific abilities, impossibility to treat all organic materials) and associated recommendations. Actions undertaken by the ADEME are evoked. In conclusion, the publication outlines some priorities related to the development of this sector, its benefits, and the main strategic recommendations

  15. Chemical pretreatment of lignocellulosic agroindustrial waste for methane production.

    Science.gov (United States)

    Pellera, Frantseska-Maria; Gidarakos, Evangelos

    2018-01-01

    This study investigates the effect of different chemical pretreatments on the solubilization and the degradability of different solid agroindustrial waste, namely winery waste, cotton gin waste, olive pomace and juice industry waste. Eight different reagents were investigated, i.e. sodium hydroxide (NaOH), sodium bicarbonate (NaHCO 3 ), sodium chloride (NaCl), citric acid (H 3 Cit), acetic acid (AcOH), hydrogen peroxide (H 2 O 2 ), acetone (Me 2 CO) and ethanol (EtOH), under three condition sets resulting in treatments of varying intensity, depending on process duration, reagent dosage and temperature. Results indicated that chemical pretreatment under more severe conditions is more effective on the solubilization of lignocellulosic substrates, such as those of the present study and among the investigated reagents, H 3 Cit, H 2 O 2 and EtOH appeared to be the most effective to this regard. At the same time, although chemical pretreatment in general did not improve the methane potential of the substrates, moderate to high severity conditions were found to generally be the most satisfactory in terms of methane production from pretreated materials. In fact, moderate severity treatments using EtOH for winery waste, H 3 Cit for olive pomace and H 2 O 2 for juice industry waste and a high severity treatment with EtOH for cotton gin waste, resulted in maximum specific methane yield values. Ultimately, the impact of pretreatment parameters on the different substrates seems to be dependent on their characteristics, in combination with the specific mode of action of each reagent. The overall energy balance of such a system could probably be improved by using lower operating powers and higher solid to liquid ratios. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. Waste energy boosts tomato industry at distillery

    Energy Technology Data Exchange (ETDEWEB)

    McColl, J

    1989-04-01

    A trial project aimed at using waste hot water from the cooling process at a Scottish whisky distillery to heat a glasshouse for tomato production is described. Later developments have involved the installation of a waste heat boiler to make use of the heat from the still burner flue gases. Steam from the boiler is used within the distillery and to supplement the glasshouse system. The payback within the distillery industry has been excellent, but tomato production, though continuing, was adversely affected by severe cutbacks in distillery production in the early eighties. Recently further significant savings have been made in the distillery industry by the installation of a regenerative burner in one of the stills and thermo-compressors in the cooling tower condensers to produce low pressure steam which can be fed back into the system. (U.K.).

  17. Chemicals Industry New Process Chemistry Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2000-08-01

    The Materials Technology I workshop was held in November 1998 to address future research needs for materials technology that will support the chemical industry. Areas covered included disassembly, recovery, reuse and renewable technology; new materials; and materials measurement and characterization. The Materials Technology II workshop was held in September 1999 and covered additives, modeling and prediction and an additional segment on new materials. Materials Technology Institute (MTI) for the Chemical Process Industries, Inc. and Air Products & Chemicals lead the workshops. The Materials Technology Roadmap presents the results from both workshops.

  18. Cleaner production for solid waste management in leather industry ...

    African Journals Online (AJOL)

    Cleaner production for solid waste management in leather industry. ... From the processes, wastes are generated which include wastewater effluents, solid wastes, and hazardous wastes. In developing countries including Ethiopia, many ... The solid waste inventory of the factory has been carried out. The major problems ...

  19. Alpha waste incineration prototype incinerator and industrial project

    International Nuclear Information System (INIS)

    Caramelle, D.; Meyere, A.

    1988-01-01

    To meet our requirements with respect to the processing of solid alpha wastes, a pilot cold incinerator has been used for R and D. This unit has a capacity of 5 kg/hr. The main objectives assigned to this incineration process are: a good reduction factor, controlled combustion, ash composition compatible with plutonium recovery, limited secondary solid and fluid wastes, releases within the nuclear and chemical standards, and in strict observance of the confinement and criticality safety rules. After describing the process we will discuss the major results of the incineration test campaigns with representative solid wastes (50 % PVC). We will then give a description of an industrial project with a capacity of 7 kg/hr, followed by a cost estimate

  20. Problems of placement of industrial wastes in landfills in the industrial city

    Directory of Open Access Journals (Sweden)

    STEPANOV Evgeniy Georgievich,

    2017-04-01

    Full Text Available The article shows that the anthropogenic transformation of the environment increases when production wastes and consumption are placed in landfills. Hygienic condition of the areas with high population density and developed industry is determined by the increased amount of household and industrial waste, mainly deposited in the numerous landfills. This situation is studied on the example of landfills used for industrial wastes produced by the enterprises JSC «Gazprom Neftekhim Salavat», JSC «Salavatsteklo», located in the city of Salavat of the Republic of Bashkortostan. The sources of industrial pollution in Salavat have been analyzed. One should note that the city-forming enterprise is the JSC «Gazprom Neftekhim Salavat» which share of the total amount of wastes generated in the city per year is 80%. Another company which contributes significantly to this process is the JSC «Salavatsteklo». To study the possible migration of contaminants to the aquifer an observation well has been made at the landfill site. The research of the water obtained from the observation well at the polygon identified maximum allowable concentrations for chemical oxygen demand (COD, phenol and oil products. The groundwater occurrence modes have been studied. The migration of the chemicals contained in the body of the landfill, to groundwater, has been revealed. That leads to contamination of surface water. Laboratory studies of water objects in the zone of influence of industrial waste landfill in Romodanovskomu career have been performed. It was determined that excess of maximum permissible concentration of benzene, and the presence of toluene, lead, phenol indicates the pollution of groundwater by substances stored in landfills Romanovskogo career, both by infiltration and subsequent migration to groundwater of adjacent aquifers and through surface runoff and infiltration from snowmelt and rainwater.

  1. Does industrial waste taxation contribute to reduction of landfilled waste? Dynamic panel analysis considering industrial waste category in Japan.

    Science.gov (United States)

    Sasao, Toshiaki

    2014-11-01

    Waste taxes, such as landfill and incineration taxes, have emerged as a popular option in developed countries to promote the 3Rs (reduce, reuse, and recycle). However, few studies have examined the effectiveness of waste taxes. In addition, quite a few studies have considered both dynamic relationships among dependent variables and unobserved individual heterogeneity among the jurisdictions. If dependent variables are persistent, omitted variables cause a bias, or common characteristics exist across the jurisdictions that have introduced waste taxes, the standard fixed effects model may lead to biased estimation results and misunderstood causal relationships. In addition, most existing studies have examined waste in terms of total amounts rather than by categories. Even if significant reductions in total waste amounts are not observed, some reduction within each category may, nevertheless, become evident. Therefore, this study analyzes the effects of industrial waste taxation on quantities of waste in landfill in Japan by applying the bias-corrected least-squares dummy variable (LSDVC) estimators; the general method of moments (difference GMM); and the system GMM. In addition, the study investigates effect differences attributable to industrial waste categories and taxation types. This paper shows that industrial waste taxes in Japan have minimal, significant effects on the reduction of final disposal amounts thus far, considering dynamic relationships and waste categories. Copyright © 2014 Elsevier Ltd. All rights reserved.

  2. Wireless sensor networks in chemical industry

    International Nuclear Information System (INIS)

    Minhas, A.A.; Jawad, S.

    2010-01-01

    Recent advances in wireless technology are a clear indication of the commercial promise of wireless networks. Industrial wireless sensing has now become more economical, efficient and secure as compared to traditional wired sensing. Wireless Sensor Networks (WSN) are successfully being used for process monitoring and control of many industrial plants. This paper explores how Chemical Industry in particular can benefit from the application of WSN technology. Various examples of successful implementation are cited. In order to address the industrial requirements, we propose a low power and low cost solution for process monitoring by implementing WSN. (author)

  3. Utilizing environmental management information systems to monitor chemical usage and facilitate waste minimization

    Energy Technology Data Exchange (ETDEWEB)

    Blazer, T.L.; Kinney, R.W. [Modern Technologies Corporation, Dayton, OH (United States)

    1996-10-01

    Waste minimization and pollution prevention activities have proven to be valuable to the chemical industry`s and the chemical user`s bottom line. Many companies have found that, with a modest initial capital investment and product modifications, mounds of bureaucratic liability can be removed and substantial cost savings can be realized.

  4. Waste to chemicals for a circular economy.

    Science.gov (United States)

    Iaquaniello, Gaetano; Centi, Gabriele; Annarita Salladini, Annarita; Palo, Emma; Perathoner, Siglinda

    2018-06-25

    The implementation of a circular economy is a fundamental step to create a greater and more sustainable future for a better use of resources and energy. Wastes and in particular municipal solid waste represent an untapped source of carbon (and hydrogen) to produce a large range of chemicals from methane to alcohols (as methanol or ethanol) or urea. The waste to chemical (WtC) process and related economics are assessed in this concept article to show the validity of such solution both from an economic point of view and from an environmental perspective considering the sensible reduction in greenhouse gas emissions with respect to conventional production from fossil fuels. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Failure analysis on a chemical waste pipe

    International Nuclear Information System (INIS)

    Ambler, J.R.

    1985-01-01

    A failure analysis of a chemical waste pipe illustrates how nuclear technology can spin off metallurgical consultant services. The pipe, made of zirconium alloy (Zr-2.5 wt percent Nb, UNS 60705), had cracked in several places, all at butt welds. A combination of fractography and metallography indicated delayed hydride cracking

  6. Logistic paradigm for industrial solid waste treatment processes

    OpenAIRE

    Janusz Grabara; Ioan Constantin Dima

    2014-01-01

    Due to the fact that industrial waste are a growing problem, both economic and environmental as their number is increasing every year, it is important to take measures to correctly dealing wi th industrial waste. This article presents the descriptive model of logistics processes concerning the management of industrial waste. In this model the flow of waste begins in the place of production and ends at their disposal. The article presents the concept of logistics model in graphical form...

  7. The treatment and disposal of liquid waste in the nuclear power industry

    International Nuclear Information System (INIS)

    Lewis, J.B.

    1978-01-01

    Paper presented by the head of the Industrial Chemistry Group at AERE Harwell at a symposium held by the University of Newcastle upon Tyne (UK) in association with the Institute of Water Pollution Control and the Institution of Chemical Engineers in September 1977. Main headings are as follows: general introduction; units of measurement of radioactivity; environmental considerations (disposal authorisations, natural background, critical path approach, discharges to the sea, discharges to rivers); types of liquid waste (general, high level wastes, wastes from chemical processing stages, wastes from nuclear power stations, miscellaneous wastes); treatment techniques (general, evaporation, chemical precipitation, ion exchange, reverse osmosis, electrodialysis); disposal of radioactive concentrates (high level wastes, sludges, exhausted ion exchangers, etc.). It is concluded that the main task remaining is to find the best means of ultimate disposal of high level wastes. (U.K.)

  8. Disintegration-wave method of recovery of industrial waste iron and steel industry enterprises

    Directory of Open Access Journals (Sweden)

    M. A. Vasechkin

    2016-01-01

    Full Text Available Rational use of raw materials and waste is one of the most important factors determining the effectiveness of any processing enterprise. Industrial wastes of mining and metallurgical industries are a valuable source of many elements. However, little activity of the mineral and inconsistent chemical and phase composition of the waste reduce their attractiveness for use as a secondary raw material, and the presence of heavy metals and water-soluble compounds is a serious environmental threat. Fractional excretion of elements that make up the slag can be carried out with the help of their recovery by disintegration-wave method. The paper presents a machine-hardware circuits for the implementation of recovery process of slag and disintegrator design. In conducting research on the example of slag samples of the enterprises in Stavropol and Krasnoyarsk territories, it was found out that the observed enrichment of slags on the composition of iron takes place, its physical and chemical activity increases and persists for a long period of time. These facts were noted in the study of the microstructure and the results of spectral analysis of the initial slags and subjected to recovery by disintegration-wave method. The results analysis led to the conclusion about the possibility of waste recovery of mining and metallurgical industries with by disintegration-wave method. Resulting in the processing materials with enhanced activity of the mineral part and certain chemical and phase composition, can be used as raw material for the production of metallurgical, cement and other industries.

  9. Metallurgical engineering and inspection practices in the chemical process industries

    International Nuclear Information System (INIS)

    Moller, G.E.

    1987-01-01

    The process industries, in particular the petroleum refining industry, adopted materials engineering and inspection (ME and I) practices years ago and regularly updated them because they were faced with the handling and refining of flammable, toxic, and corrosive feed stocks. These industries have a number of nonproprietary techniques and procedures, some of which may be applicable in the nuclear power generation field. Some specific inspection and engineering techniques used by the process industries within the framework of the guidelines for inspections and worthy of detailed description include the following: (1) sentry drilling or safety drilling of piping subject to relatively uniform corrosion, such as feedwater heater piping, steam piping, and extraction steam piping; (2) on-stream radiography for thickness measurement and detection of unusual conditions - damaged equipment such as valve blockage; (3) critical analysis of the chemical and refining processes for the relative probability of corrosion; (4) communication of valuable experience within the industry; (5) on-stream ultrasonic thickness testing; and (6) on-stream and off-stream crack and flaw detection. The author, trained in the petroleum refining industry but versed in electric utilities, pulp and paper, chemical process, marine, mining, water handling, waste treatment, and geothermal processes, discusses individual practices of these various industries in the paper

  10. Conversion of food industrial wastes into bioplastics.

    Science.gov (United States)

    Yu, P H; Chua, H; Huang, A L; Lo, W; Chen, G Q

    1998-01-01

    The usage of plastics in packaging and disposable products, and the generation of plastic waste, have been increasing drastically. Broader usage of biodegradable plastics in packaging and disposable products as a solution to environmental problems would heavily depend on further reduction of costs and the discovery of novel biodegradable plastics with improved properties. In the authors' laboratories, various carbohydrates in the growth media, including sucrose, lactic acid, butyric acid, valeric acid, and various combinations of butyric and valeric acids, were utilized as the carbon (c) sources for the production of bioplastics by Alcaligenes eutrophus. As the first step in pursuit of eventual usage of industrial food wastewater as nutrients for microorganisms to synthesize bioplastics, the authors investigated the usage of malt wastes from a beer brewery plant as the C sources for the production of bioplastics by microorganisms. Specific polymer production yield by A. Latus DSM 1124 increased to 70% polymer/cell (g/g) and 32 g/L cell dry wt, using malt wastes as the C source. The results of these experiments indicated that, with the use of different types of food wastes as the C source, different polyhydroxyalkanoate copolymers could be produced with distinct polymer properties.

  11. Nuclear techniques in coal and chemical industries

    International Nuclear Information System (INIS)

    Elbern, A.W.; Leal, C.A.

    1980-01-01

    The use of nuclear techniques for the determination of important parameters in industrial installations is exemplified; advantages of these techniques over other methods conventionally used are pointed out. The use of radiotracers in the study of physical and chemical phenomena occurring in the chemical industry is discussed. It is also shown that, using certain radioisotopes, it is possible to construct devices which enable, for example, the determination of the ash content in coal samples. These devices are economical and easy to be installed for the on-line control during coal transportation. (C.L.B.) [pt

  12. PHYSICO-CHEMICAL ANALYSIS OF THE WASTE FROM INSTALLATION OF SEMI-DRY FLUE GAS DESULFURIZATION OF INDUSTRIAL CHP PLANT IN JANIKOWO

    Directory of Open Access Journals (Sweden)

    Marta Plaskacz-Dziuba

    2014-10-01

    Full Text Available The paper presents results of the analysis of waste from semi-dry flue gas desulphurisation installation called Integrated Novel Desulphurisation (NID. A comprehensive analysis of the physicochemical properties was conducted, including analyzes of the content of ions SO32- and SO42- (relating to 2CaSO3·H2O i CaSO4·2H2O, moisture, SiO2 and R2O3 and SEM-EDX analysis. The original method for the determination of sulphates (IV using a potentiometric titrator was designed. Determined that the main component of both studied wastes was 2CaSO3·H2O, and its content is for NID 1 – 41,24±0,63%, for NID 2 – 45,53±0,33%. The content of CaSO4·2H2O, which was determined by gravimetric method amounted for the NID 1 – 8,92±0,12%, for the NID 2 – 8,27±0,08%. The moisture content for both tested materials was about 4%, the content of SiO2 was in the range of 8–10%, and R2O3 content was about 1%. It was also shown that the test material is not homogenous. Images from scanning electron microscope showed that in the waste occured irregularly agglomerates with a diameter between 30 and 100 microns. EDX analysis revealed that elements constituted NID wastes are oxygen, sulfur, calcium, chlorine, silicon, aluminum, copper and carbon.

  13. Ecotoxicity of waste water from industrial fires fighting

    Science.gov (United States)

    Dobes, P.; Danihelka, P.; Janickova, S.; Marek, J.; Bernatikova, S.; Suchankova, J.; Baudisova, B.; Sikorova, L.; Soldan, P.

    2012-04-01

    As shown at several case studies, waste waters from extinguishing of industrial fires involving hazardous chemicals could be serious threat primary for surrounding environmental compartments (e.g. surface water, underground water, soil) and secondary for human beings, animals and plants. The negative impacts of the fire waters on the environment attracted public attention since the chemical accident in the Sandoz (Schweizerhalle) in November 1986 and this process continues. Last October, special Seminary on this topic has been organized by UNECE in Bonn. Mode of interaction of fire waters with the environment and potential transport mechanisms are still discussed. However, in many cases waste water polluted by extinguishing foam (always with high COD values), flammable or toxic dangerous substances as heavy metals, pesticides or POPs, are released to surface water or soil without proper decontamination, which can lead to environmental accident. For better understanding of this type of hazard and better coordination of firemen brigades and other responders, the ecotoxicity of such type of waste water should be evaluated in both laboratory tests and in water samples collected during real cases of industrial fires. Case studies, theoretical analysis of problem and toxicity tests on laboratory model samples (e.g. on bacteria, mustard seeds, daphnia and fishes) will provide additional necessary information. Preliminary analysis of waters from industrial fires (polymer material storage and galvanic plating facility) in the Czech Republic has already confirmed high toxicity. In first case the toxicity may be attributed to decomposition of burned material and extinguishing foams, in the latter case it can be related to cyanides in original electroplating baths. On the beginning of the year 2012, two years R&D project focused on reduction of extinguish waste water risk for the environment, was approved by Technology Agency of the Czech Republic.

  14. Container for processing and disposing radioactive wastes and industrial wastes

    International Nuclear Information System (INIS)

    Araki, Kunio; Kasahara, Yuko; Kasai, Noboru; Sudo, Giichi; Ishizaki, Kanjiro.

    1978-01-01

    Purpose: To improve the performance of containers for radioactive wastes for ocean disposal and on-land disposal such as impact strength, chemical resistance, fire resistance, corrosion resistance, water impermeability and the like. Constitution: Steel fiber-reinforced concrete previously molded in a shape of a container is impregnated with polymerizable impregnating agent selected from the group consisting of a polymerizable monomer, liquid mixture of a polymerizable monomer and an oligomer, a polymer solution, a copolymer solution and the liquid mixture thereof. Then, the polymerizable impregnating agent is polymerized to solidify in the concrete by way of heat-polymerization or radiation-induced polymerization to form a waste container. The container thus obtained can be improved with the impact resistance and wear resistance and further improved with salt water resistance, acid resistance, corrosion resistance and solidity by the impregnation of the polymer, as well as can effectively be prevented from leaching out of radioactive substances. (Furukawa, Y.)

  15. Mixed waste chemical compatibility with packaging components

    International Nuclear Information System (INIS)

    Nigrey, P.J.; Conroy, M.; Blalock, L.B.

    1994-01-01

    In this paper, a chemical compatibility testing program for packaging of mixed wastes at will be described. We will discuss the choice of four y-radiation doses, four time durations, four temperatures and four waste solutions to simulate the hazardous waste components of mixed wastes for testing materials compatibility of polymers. The selected simulant wastes are (1) an aqueous alkaline mixture of sodium nitrate and sodium nitrite; (2) a chlorinated hydrocarbon mixture; (3) a simulant liquid scintillation fluid; and (4) a mixture of ketones. A selection of 10 polymers with anticipated high resistance to one or more of these types of environments are proposed for testing as potential liner or seal materials. These polymers are butadiene acrylonitrile copolymer, cross-linked polyethylene, epichlorhyarin, ethylene-propylene rubber, fluorocarbon, glass-filled tetrafluoroethylene, high-density poly-ethylene, isobutylene-isoprene copolymer, polypropylene, and styrene-butadiene rubber. We will describe the elements of the testing plan along with a metric for establishing time resistance of the packaging materials to radiation and chemicals

  16. Chemical decontamination method for radioactive metal waste

    International Nuclear Information System (INIS)

    Tanaka, Akio; Onuma, Tsutomu; Yamazaki, Sei; Miura, Haruki.

    1993-01-01

    The present invention provides a chemical decontamination method for radioactive metal wastes, which are generated from radioactive material handling facilities and the surfaces of which are contaminated by radioactive materials. That is, it has a feature of applying acid dissolution simultaneously with mechanical grinding. The radioactive metal wastes are contained in a vessel such as a barrel together with abrasives in a sulfuric acid solution and rotated at several tens rotation per minute. By such procedures for the radioactive metal wastes, (1) cruds and passive membranes are mechanically removed, (2) exposed mother metal materials are uniformly brought into contact with sulfuric acid and further (3) the mother metal materials dissolve the cruds and the passive membranes also chemically by a reducing dissolution (so-called local cell effect). According to the method of the present invention, stainless steel metal wastes having cruds and passive membranes can rapidly and efficiently be decontaminated to a radiation level equal with that of ordinary wastes. (I.S.)

  17. Assessment of logistic outlays in industrial solid waste management

    Directory of Open Access Journals (Sweden)

    Janusz Grabara

    2014-12-01

    Full Text Available Out of concern for environmental protection is an increasingly common practice. Companies thus have an additional task which is the correct organization of the industrial waste management. This is achieved through the use of logistics processes in industrial waste management, mainly such as warehousing, transport, storage and recovery. These processes involve the formation of logistics costs resulting from waste management. The paper presents a mathematical model for cost of logistics management of industrial waste resulting from the above-mentioned processes. It also shows the interpretation of these costs and the relations between them. The model can increase costefficiency in companies managing industrial waste, while increasing attention to the environment.

  18. Research and chemical industry in 90's

    International Nuclear Information System (INIS)

    Trapasso, I.

    1992-01-01

    This paper examines the importance of research with respect to changes taking place within the chemical industry. Specific areas having a significant impact on the future evolution of the industry are identified. The chemical industry is highly R ampersand D intensive with respect to its overall sales volume, as well as, to R ampersand D levels in other industries; and R ampersand D has been a dominant factor influencing the restructuring, on a global scale, of this industry. In the 90's, the industry is expected to have a supply model which is based on the production of marketable high-technology products and integrated systems, developed through coordinated research in multi-disciplinary scientific fields. The optimum strategic and organizational strategies which are to be adopted by the industry during this decade are discussed with reference to the directions being taken by a large multi-national firm in developing strategies in various areas, e.g., new prime materials, environmental protection, pharmacology, and biotechnology. A look is given at recent developments in the sector of advanced polymers, with attention given to processes involving polymer genetics, new products with a wide range of applications and those offering a high level of environmental compatibility. A review of new materials development includes an assessment of prospects for biodegradable plastics based on natural carbohydrates

  19. Safety Considerations in the Chemical Process Industries

    Science.gov (United States)

    Englund, Stanley M.

    There is an increased emphasis on chemical process safety as a result of highly publicized accidents. Public awareness of these accidents has provided a driving force for industry to improve its safety record. There has been an increasing amount of government regulation.

  20. Immobilization of industrial waste in cement–bentonite clay matrix

    Indian Academy of Sciences (India)

    Unknown

    Immobilization of industrial waste in cement–bentonite clay matrix. I B PLECAS* and S ... high structural integrity and minimizing the risk of escape by leaching. ..... Radioactive Waste Management and Nuclear Fuel Cycle 14. 195. Plecas I ...

  1. Recycled industrial and construction waste for mutual beneficial use.

    Science.gov (United States)

    2016-08-01

    Instead of going to landfills, certain waste materials from industry and building construction can be recycled in transportation infrastructure projects, such as roadway paving. The beneficial use of waste materials in the construction of transportat...

  2. ASSESSMENT OF TOXICITY OF INDUSTRIAL WASTES USING CROP PLANT ASSAYS

    Directory of Open Access Journals (Sweden)

    Carmen Alice Teacă

    2008-11-01

    Full Text Available Environmental pollution has a harmful action on bioresources, including agricultural crops. It is generated through many industrial activities such as mining, coal burning, chemical technology, cement production, pulp and paper industry, etc. The toxicity of different industrial wastes and heavy metals excess was evaluated using crop plant assays (germination and hydroponics seedlings growth tests. Experimental data regarding the germination process of wheat (from two cultivars and rye seeds in the presence of industrial wastes (thermal power station ash, effluents from a pre-bleaching stage performed on a Kraft cellulose – chlorinated lignin products or chlorolignin, along with use of an excess of some heavy metals (Zn and Cu are presented here. Relative seed germination, relative root elongation, and germination index (a factor of relative seed germination and relative root elongation were determined. Relative root elongation and germination index were more sensitive indicators of toxicity than seed germination. The toxic effects were also evaluated in hydroponics experiments, the sensitivity of three crop plant species, namely Triticum aestivum L. (wheat, Secale cereale (rye, and Zea mays (corn being compared. Physiological aspects, evidenced both by visual observation and biometric measurements (mean root, aerial part and plant length, as well as the cellulose and lignin content were examined.

  3. Laboratory scale studies on removal of chromium from industrial wastes.

    Science.gov (United States)

    Baig, M A; Mir, Mohsin; Murtaza, Shazad; Bhatti, Zafar I

    2003-05-01

    Chromium being one of the major toxic pollutants is discharged from electroplating and chrome tanning processes and is also found in the effluents of dyes, paint pigments, manufacturing units etc. Chromium exists in aqueous systems in both trivalent (Cr(3+)) and hexavalent (Cr(6+)) forms. The hexavalent form is carcinogenic and toxic to aquatic life, whereas Cr(3+) is however comparatively less toxic. This study was undertaken to investigate the total chromium removal from industrial effluents by chemical means in order to achieve the Pakistan NEQS level of 1 mg/L by the methods of reduction and precipitation. The study was conducted in four phases. In phase I, the optimum pH and cost effective reducing agent among the four popular commercial chemicals was selected. As a result, pH of 2 was found to be most suitable and sodium meta bisulfate was found to be the most cost effective reducing agent respectively. Phase II showed that lower dose of sodium meta bisulfate was sufficient to obtain 100% efficiency in reducing Cr(6+) to Cr(3+), and it was noted that reaction time had no significance in the whole process. A design curve for reduction process was established which can act as a tool for treatment of industrial effluents. Phase III studies indicated the best pH was 8.5 for precipitation of Cr(3+) to chromium hydroxide by using lime. An efficiency of 100% was achievable and a settling time of 30 minutes produced clear effluent. Finally in Phase IV actual waste samples from chrome tanning and electroplating industries, when precipitated at pH of 12 gave 100% efficiency at a settling time of 30 minutes and confined that chemical means of reduction and precipitation is a feasible and viable solution for treating chromium wastes from industries.

  4. Industrial waste utilization for foam concrete

    Science.gov (United States)

    Krishnan, Gokul; Anand, K. B.

    2018-02-01

    Foam concrete is an emerging and useful construction material - basically a cement based slurry with at least 10% of mix volume as foam. The mix usually containing cement, filler (usually sand) and foam, have fresh densities ranging from 400kg/m3 to 1600kg/m3. One of the main drawbacks of foam concrete is the large consumption of fine sand as filler material. Usage of different solid industrial wastes as fillers in foam concrete can reduce the usage of fine river sand significantly and make the work economic and eco-friendly. This paper aims to investigate to what extent industrial wastes such as bottom ash and quarry dust can be utilized for making foam concrete. Foam generated using protein based agent was used for preparing and optimizing (fresh state properties). Investigation to find the influence of design density and air-void characteristics on the foam concrete strength shows higher strength for bottom ash mixes due to finer air void distribution. Setting characteristics of various mix compositions are also studied and adoption of Class C flyash as filler demonstrated capability of faster setting.

  5. Radioactive waste management in the VS military nuclear industry

    International Nuclear Information System (INIS)

    Kobal'chuk, O.V.; Kruglov, A.K.; Sokolova, I.D.; Smirnov, Yu.V.

    1989-01-01

    Organization and plans of radioactive waste management in the US military nuclear industry, determining transition from the policy of temporal waste storage to their final and safe disposal are presented. Programs of long-term management of high-level, transuranium and low-level wastes, the problems of the work financing and the structure of management activities related to the radioactive waste processing military nuclear industry enterprises are considered

  6. Challenges in packaging waste management in the fast food industry

    Energy Technology Data Exchange (ETDEWEB)

    Aarnio, Teija [Digita Oy, P.O. Box 135, FI-00521 Helsinki (Finland); Haemaelaeinen, Anne [Department of Energy and Environmental Technology, Lappeenranta University of Technology, P.O. Box 20, FI-53851 Lappeenranta (Finland)

    2008-02-15

    The recovery of solid waste is required by waste legislation, and also by the public. In some industries, however, waste is mostly disposed of in landfills despite of its high recoverability. Practical experiences show that the fast food industry is one example of these industries. A majority of the solid waste generated in the fast food industry is packaging waste, which is highly recoverable. The main research problem of this study was to find out the means of promoting the recovery of packaging waste generated in the fast food industry. Additionally, the goal of this article was to widen academic understanding on packaging waste management in the fast food industry, as the subject has not gained large academic interest previously. The study showed that the theoretical recovery rate of packaging waste in the fast food industry is high, 93% of the total annual amount, while the actual recovery rate is only 29% of the total annual amount. The total recovery potential of packaging waste is 64% of the total annual amount. The achievable recovery potential, 33% of the total annual amount, could be recovered, but is not mainly because of non-working waste management practices. The theoretical recovery potential of 31% of the total annual amount of packaging waste cannot be recovered by the existing solid waste infrastructure because of the obscure status of commercial waste, the improper operation of producer organisations, and the municipal autonomy. The research indicated that it is possible to reach the achievable recovery potential in the existing solid waste infrastructure through new waste management practices, which are designed and operated according to waste producers' needs and demands. The theoretical recovery potential can be reached by increasing the consistency of the solid waste infrastructure through governmental action. (author)

  7. Characteristics and management of infectious industrial waste in Taiwan

    International Nuclear Information System (INIS)

    Huang, M.-C.; Lin, Jim Juimin

    2008-01-01

    Infectious industrial waste management in Taiwan is based on the specific waste production unit. In other countries, management is based simply on whether the producer may lead to infectious disease. Thus, Taiwan has a more detailed classification of infectious waste. The advantage of this classification is that it is easy to identify the sources, while the disadvantage lies in the fact that it is not flexible and hence increases cost. This study presents an overview of current management practices for handling infectious industrial waste in Taiwan, and addresses the current waste disposal methods. The number of small clinics in Taiwan increased from 18,183 to 18,877 between 2003 and 2005. Analysis of the data between 2003 and 2005 showed that the majority of medical waste was general industrial waste, which accounted for 76.9%-79.4% of total medical waste. Infectious industrial waste accounted for 19.3%-21.9% of total medical waste. After the SARS event in Taiwan, the amount of infectious waste reached 19,350 tons in 2004, an increase over the previous year of 4000 tons. Waste minimization was a common consideration for all types of waste treatment. In this study, we summarize the percentage of plastic waste in flammable infectious industrial waste generated by medical units, which, in Taiwan was about 30%. The EPA and Taiwan Department of Health have actively promoted different recycling and waste reduction measures. However, the wide adoption of disposable materials made recycling and waste reduction difficult for some hospitals. It has been suggested that enhancing the education of and promoting communication between medical units and recycling industries must be implemented to prevent recyclable waste from entering the incinerator

  8. Characterization of industrial process waste heat and input heat streams

    Energy Technology Data Exchange (ETDEWEB)

    Wilfert, G.L.; Huber, H.B.; Dodge, R.E.; Garrett-Price, B.A.; Fassbender, L.L.; Griffin, E.A.; Brown, D.R.; Moore, N.L.

    1984-05-01

    The nature and extent of industrial waste heat associated with the manufacturing sector of the US economy are identified. Industry energy information is reviewed and the energy content in waste heat streams emanating from 108 energy-intensive industrial processes is estimated. Generic types of process equipment are identified and the energy content in gaseous, liquid, and steam waste streams emanating from this equipment is evaluated. Matchups between the energy content of waste heat streams and candidate uses are identified. The resultant matrix identifies 256 source/sink (waste heat/candidate input heat) temperature combinations. (MHR)

  9. Waste incineration industry and development policies in China.

    Science.gov (United States)

    Li, Yun; Zhao, Xingang; Li, Yanbin; Li, Xiaoyu

    2015-12-01

    The growing pollution from municipal solid waste due to economic growth and urbanization has brought great challenge to China. The main method of waste disposal has gradually changed from landfill to incineration, because of the enormous land occupation by landfills. The paper presents the results of a study of the development status of the upstream and downstream of the waste incineration industry chain in China, reviews the government policies for the waste incineration power industry, and provides a forecast of the development trend of the waste incineration industry. Copyright © 2015 Elsevier Ltd. All rights reserved.

  10. Industrial aspects of radioactive waste management in Western Europe

    International Nuclear Information System (INIS)

    Marcus, F.R.

    1976-01-01

    Various aspects of waste management are discussed from the viewpoint of the nuclear industry. Future amounts of waste generated in the 15 Foratom countries in Western Europe are estimated. Industrial waste questions--as seen by electricity producers, reprocessors, and waste operators--are discussed; questions concerning decommissioning are also dealt with. A number of recommendations for further action, primarily on the part of national authorities and international organizations, are put forward. One conclusion of the study is that there is no reason for waste-management problems to impede the timely development of nuclear energy as a large-scale industrial activity in Western Europe

  11. Development of a master plan for industrial solid waste management

    International Nuclear Information System (INIS)

    Karamouz, M.; Zahraie, B.; Kerachian, R.; Mahjouri, N.; Moridi, A.

    2006-01-01

    Rapid industrial growth in the province of Khuzestan in the south west of Iran has resulted in disposal of about 1750 tons of solid waste per day. Most of these industrial solid wastes including hazardous wastes are disposed without considering environmental issues. This has contributed considerably to the pollution of the environment. This paper introduces a framework in which to develop a master plan for industrial solid waste management. There are usually different criteria for evaluating the existing solid waste pollution loads and how effective the management schemes are. A multiple criteria decision making technique, namely Analytical Hierarchy Process, is used for ranking the industrial units based on their share in solid waste related environmental pollution and determining the share of each unit in total solid waste pollution load. In this framework, a comprehensive set of direct, indirect, and supporting projects are proposed for solid waste pollution control. The proposed framework is applied for industrial solid waste management in the province of Khuzestan in Iran and a databank including GIS based maps of the study area is also developed. The results have shown that the industries located near the capital city of the province, Ahwaz, produce more than 32 percent of the total solid waste pollution load of the province. Application of the methodology also has shown that it can be effectively used for development of the master plan and management of industrial solid wastes

  12. Assessment and analysis of industrial liquid waste and sludge disposal at unlined landfill sites in arid climate

    International Nuclear Information System (INIS)

    Al Yaqout, Anwar F.

    2003-01-01

    Municipal solid waste disposal sites in arid countries such as Kuwait receive various types of waste materials like sewage sludge, chemical waste and other debris. Large amounts of leachate are expected to be generated due to the improper disposal of industrial wastewater, sewage sludge and chemical wastes with municipal solid waste at landfill sites even though the rainwater is scarce. Almost 95% of all solid waste generated in Kuwait during the last 10 years was dumped in five unlined landfills. The sites accepting liquid waste consist of old sand quarries that do not follow any specific engineering guidelines. With the current practice, contamination of the ground water table is possible due to the close location of the water table beneath the bottom of the waste disposal sites. This study determined the percentage of industrial liquid waste and sludge of the total waste dumped at the landfill sites, analyzed the chemical characteristics of liquid waste stream and contaminated water at disposal sites, and finally evaluated the possible risk posed by the continuous dumping of such wastes at the unlined landfills. Statistical analysis has been performed on the disposal and characterization of industrial wastewater and sludge at five active landfill sites. The chemical analysis shows that all the industrial wastes and sludge have high concentrations of COD, suspended solids, and heavy metals. Results show that from 1993 to 2000, 5.14±1.13 million t of total wastes were disposed per year in all active landfill sites in Kuwait. The share of industrial liquid and sludge waste was 1.85±0.19 million t representing 37.22±6.85% of total waste disposed in all landfill sites. Such wastes contribute to landfill leachate which pollutes groundwater and may enter the food chain causing adverse health effects. Lined evaporation ponds are suggested as an economical and safe solution for industrial wastewater and sludge disposal in the arid climate of Kuwait

  13. The conceptual design of waste repository for radioactive waste from medical, industrial and research facilities containing comparatively high radioactivity

    International Nuclear Information System (INIS)

    Yamamoto, Masayuki; Hashimoto, Naro

    2002-02-01

    Advisory Committee on Nuclear Fuel Cycle Backend Policy reported the basic approach to the RI and Institute etc. wastes on March 2002. According to it, radioactive waste form medical, industrial and research facilities should be classified by their radioactivity properties and physical and chemical properties, and should be disposed in the appropriate types of repository with that classification. For the radioactive waste containing comparatively high radioactivity generated from reactors, NSC has established the Concentration limit for disposal. NSC is now discussing about the limit for the radioactive waste from medical, industrial and research facilities containing comparatively high radioactivity. Japan Nuclear Cycle Development Institute (JNC) preliminary studied about the repository for radioactive waste from medical, industrial and research facilities and discussed about the problems for design on H12. This study was started to consider those problems, and to develop the conceptual design of the repository for radioactive waste from medical, industrial and research facilities. Safety assessment for that repository is also performed. The result of this study showed that radioactive waste from medical, industrial and research facilities of high activity should be disposed in the repository that has higher performance of barrier system comparing with the vault type near surface facility. If the conditions of the natural barrier and the engineering barrier are clearer, optimization of the design will be possible. (author)

  14. Hazardous and Industrial Wastes Management: a Case Study of Khazra Industrial Park, Kerman

    Directory of Open Access Journals (Sweden)

    Hossein Jafari Mansoorian

    2013-08-01

    Full Text Available Background & Aims of the Study: Increasing hazardous industrial wastes and lack of necessary regulations for management of them have led to serious problems in some parts of Iran. The aim of this study was to evaluate the situation of collection, transportation, recycling, and disposal of hazardous industrial wastes in the Khazra Industrial Park of Kerman, Iran. Materials & Methods: This study was a descriptive cross-sectional study that was done using questionnaires and local visits during year 2009. In this questionnaire, some information about the industrial wastes, production, storage on site , collection, transformation, sorting, recycling, and disposal were recorded. Results:   In the Khazra Industrial Park, 71,600 kg/day of different industrial waste is produced. The biggest proportion of waste includes metals, and construction and demolition waste which are about 16,500 tons a year. The smallest proportion is non-iron metal waste, which is produced at a rate of 8 tons per year. 88.7 percent of the active industries at the Khazra Industrial Park produce solid industrial waste. Most of the industrial units do not use a united and coordinated system for storing waste and have no specific place for temporary storage inside the industrial park. The majority of industrial waste collection, which is about 59.8%, is done by private contractors. The industrial units transfer their waste separately, and just 9 industrial units recycle their waste. Disposal of these wastes is mainly done by selling to trading agencies. Each day, 3 tons of hazardous industrial waste is produced in this park. The highest production belongs to the oil factory (Keyhan Motor. Conclusions: According to the results, the Khazra Industrial Park needs a unified system for storing, transporting and collecting the sorted waste, and it also needs to have a transportation station with basic facilities. The wastes of most industrial units at the Khazra Industrial Park have the

  15. INDUSTRIAL WASTE MANAGEMENT TO IMPROVE ENVIRONMENTAL SECURITY

    Directory of Open Access Journals (Sweden)

    V. A. Perfilov

    2016-01-01

    Full Text Available Aim. Disposal of industrial waste to improve the environmental safety by means of recycling and reusing in the manufacture of building materials.Materials and methods. We made a selection of new optimum compositions of fiber-concretes using industrial carbon black from heat generating productions, glass fibers, plasticizers, activated mixing water produced using an ultrasonic unit.Results. New fiber-reinforced concrete compositions were developed using carbon black as an additive. As a result of the processing of the experimental data, it has been revealed that introduction of carbon black as an additive contributed to the increase of the strength characteristics of nearly all fiber-reinforced concrete compositions. It has been found that microparticles of carbon black accumulate the products of hydration of portlandcement-hydrosilicate calcium on the surface and contribute to the formation of a solid microarming concrete structure.Conclusions. The use of industrial carbon black in fibrous concrete mixture using restructured water improves its rheological properties, reduces its segregation and improves the homogeneity of the concrete. Recycling and re-using carbon black in the production of building materials will improve the environmental ecology.

  16. Industrial solid and liquid waste treatment processes; Les procedes de traitement des dechets industriels solides et liquides

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    1995-11-01

    This catalogue gives information on 68 chemical, mechanical, magnetic, electrical, thermal, etc. techniques for the processing of solid, viscous and liquid, common or special, industrial wastes. The various processes are presented as files, which are easily retrievable through keywords, waste type or industry codes, processing types, distributors. Technologies, performances and applications of each techniques are presented, together with references and company contacts

  17. Industrial emerging chemicals in the environment

    Directory of Open Access Journals (Sweden)

    Vojinović-Miloradov Mirjana B.

    2014-01-01

    Full Text Available In the recent time, considerable interest has grown concerning the presence of the emerging industrial chemicals, EmIC. They are contaminants that have possible pathway to enter to the environment and they are dominantly released by industrial and anthropogenic activities. EmIC are applied in different fields using as industrial chemicals (new and recently recognized, global organic contaminants (flame retardant chemicals, pharmaceuticals (for both human and animal uses, endocrine-modulating compounds, biological metabolites, personal care products, household chemicals, nanomaterial (energy storage products, lubricants, anticorrosive and agriculture chemicals and others that are applied to a wide variety of everyday items such as clothing, upholstery, electronics and automobile interiors. NORMAN (Network of reference laboratories for monitoring of emerging environmental pollutants has established an open, dynamic, list of emerging substances and pollutants. EmIC have been recently detected in the environment due to their long-term presence, pseudo-persistence and increased use. Improvements in sophisticated analytical methods and time integrative passive sampling have enabled the identification and quantification of EmIC, in very low concentrations (ppb, ppt and lower, which likely have been present in all environmental mediums for decades. Passive technology is an innovative technique for the time-integrated measurement of emerging contaminants in water, sediment, soil and air. Passive samplers are simple handling cost-effective tool that could be used in environmental monitoring programmes. These devices are now being considered as a part of an emerging strategy for monitoring a range of emerging industrial chemicals and priority pollutants in the aquatic environment. EmIC are substances that are not included in the routine monitoring programmes and whose fate, behaviour and (ecotoxicological effects are still not well understood. Emerging

  18. Mechanical and chemical recycling of solid plastic waste.

    Science.gov (United States)

    Ragaert, Kim; Delva, Laurens; Van Geem, Kevin

    2017-11-01

    This review presents a comprehensive description of the current pathways for recycling of polymers, via both mechanical and chemical recycling. The principles of these recycling pathways are framed against current-day industrial reality, by discussing predominant industrial technologies, design strategies and recycling examples of specific waste streams. Starting with an overview on types of solid plastic waste (SPW) and their origins, the manuscript continues with a discussion on the different valorisation options for SPW. The section on mechanical recycling contains an overview of current sorting technologies, specific challenges for mechanical recycling such as thermo-mechanical or lifetime degradation and the immiscibility of polymer blends. It also includes some industrial examples such as polyethylene terephthalate (PET) recycling, and SPW from post-consumer packaging, end-of-life vehicles or electr(on)ic devices. A separate section is dedicated to the relationship between design and recycling, emphasizing the role of concepts such as Design from Recycling. The section on chemical recycling collects a state-of-the-art on techniques such as chemolysis, pyrolysis, fluid catalytic cracking, hydrogen techniques and gasification. Additionally, this review discusses the main challenges (and some potential remedies) to these recycling strategies and ground them in the relevant polymer science, thus providing an academic angle as well as an applied one. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. A Study on the Waste Water Treatment Technology for Steel Industry: Recycle And Reuse.

    OpenAIRE

    Sanjeev Kumar Sinha; Vikas Kumar Sinha; Samir Kr. Pandey; Anup Tiwari

    2016-01-01

    The steel industry is one of the most important and vital Industry of the present and the future. It is the asset of a nation. Steel plants use a tremendous amount of water for waste transfer, cooling and dust control. The steel plants have sintering mills, coke plants, blast furnaces, chemical byproducts and chemical processes, water cooled rolls, pumps, extrusion experiment, transfer lines for sludges and slurries. All these plants use a tremendous amount of water to cool the pr...

  20. Norm waste in oil and gas industry: The Syrian experience

    International Nuclear Information System (INIS)

    Al-Masri, M.S.; Suman, H.

    2001-01-01

    This paper describes the Syrian experience in respect to Naturally Occurring Radioactive Materials (NORM) waste in Syrian oil and gas industry. NORM can be concentrated and accumulated in tubing and surface equipment of oil and gas production lines in the form of scale and sludge. NORM waste (scale, sludge, production water) is therefore generated during cleaning, physical or chemical treatment of streams. Uncontrolled disposal of this type of waste could lead to environmental pollution, and thus eventually to exposure of members of the public. The presence of NORM in Syrian oil fields has been recognized since 1987 and AECS has initiated several studies, in cooperation with oil companies, to manage such type of waste. Three categories of NORM waste in Syrian oil fields were identified. Firstly, hard scales from either decontamination of contaminated equipment and tubular using high-pressure water systems or mechanical cleaning at site are considered to contain the highest levels of radium isotopes ( 226 Ra, 228 Ra, 224 Ra). Secondly, sludge wastes are generated with large amount but low levels of radium isotopes were found. Thirdly, contaminated soil with 226 Ra as a result of uncontrolled disposal of production water was also considered as NORM waste. The first waste type (scale) is stored in Standard storage barrels in a controlled area; the number of barrels is increasing with time. High levels of radium isotopes were found in these scales. The options for disposal of these wastes are still under investigations; one of the most predominant thinking is the re-injection into abundant wells. For sludge waste, plastic lined disposal pits were constructed in each area for temporary storage. Moreover, big gas power stations have been built and operated since the last ten years. Maintenance operations for these stations produce tens of tones of scales containing radon daughters, 210 Pb and 210 Po with relatively high concentrations. The common practice used to dispose

  1. Iron and aluminium oxides containing industrial wastes as adsorbents of heavy metals: Application possibilities and limitations.

    Science.gov (United States)

    Jacukowicz-Sobala, Irena; Ociński, Daniel; Kociołek-Balawejder, Elżbieta

    2015-07-01

    Industrial wastes with a high iron or aluminium oxide content are produced in huge quantities as by-products of water treatment (water treatment residuals), bauxite processing (red mud) and hard and brown coal burning in power plants (fly ash). Although they vary in their composition, the wastes have one thing in common--a high content of amorphous iron and/or aluminium oxides with a large specific surface area, whereby this group of wastes shows very good adsorbability towards heavy metals, arsenates, selenates, etc. But their physical form makes their utilisation quite difficult, since it is not easy to separate the spent sorbent from the solution and high bed hydraulic resistances occur in dynamic regime processes. Nevertheless, because of the potential benefits of utilising the wastes in industrial effluent treatment, this issue attracts much attention today. This study describes in detail the waste generation processes, the chemical structure of the wastes, their physicochemical properties, and the mechanisms of fixing heavy metals and semimetals on the surface of iron and aluminium oxides. Typical compositions of wastes generated in selected industrial plants are given. A detailed survey of the literature on the adsorption applications of the wastes, including methods of their thermal and chemical activation, as well as regeneration of the spent sorbents, is presented. The existing and potential ways of modifying the physical form of the discussed group of wastes, making it possible to overcome the basic limitation on their practical use, are discussed. © The Author(s) 2015.

  2. Chemical Education: A Tool for Wealth Creation from Waste ...

    African Journals Online (AJOL)

    This paper focuses on exposing the indispensible role of chemical education in wealth creation from waste. Every settlement of people has one type of waste or the other to dispose. The challenge of waste management has in recent time occupied researchers such that innovations are geared towards reducing wastes that ...

  3. Bioremediation of Industrial Waste Through Enzyme Producing Marine Microorganisms.

    Science.gov (United States)

    Sivaperumal, P; Kamala, K; Rajaram, R

    Bioremediation process using microorganisms is a kind of nature-friendly and cost-effective clean green technology. Recently, biodegradation of industrial wastes using enzymes from marine microorganisms has been reported worldwide. The prospectus research activity in remediation area would contribute toward the development of advanced bioprocess technology. To minimize industrial wastes, marine enzymes could constitute a novel alternative in terms of waste treatment. Nowadays, the evidence on the mechanisms of bioremediation-related enzymes from marine microorganisms has been extensively studied. This review also will provide information about enzymes from various marine microorganisms and their complexity in the biodegradation of comprehensive range of industrial wastes. © 2017 Elsevier Inc. All rights reserved.

  4. Decolorization of Industrial Waste Using Fenton Process and Photo Fenton

    OpenAIRE

    Wardiyati, Siti; Dewi, Sari Hasnah; Fisli, Adel

    2013-01-01

    Industrial waste water decolorization has been done using the method of Fenton and Photo Fenton. The experiment was conducted in order to obtain the optimum process conditions for industrial waste treatment method with Fenton and Photo Fenton. Industrial waste used in this experiment waste of blue batik making process derived from Rara Djograng Batik Yogyakarta. Factors were studied in this research are the effect of the amount of catalyst FeSO4.7H2O, the amount of oxidant H2O2, and the time ...

  5. Characterization study of industrial waste glass as starting material ...

    African Journals Online (AJOL)

    In present study, an industrial waste glass was characterized and the potential to assess as starting material in development of bioactive materials was investigated. A waste glass collected from the two different glass industry was grounded to fine powder. The samples were characterized using X-ray fluorescence (XRF), ...

  6. FY 1999 report on the results of the introductory study on the global environmental industry technology. Study of the technology to recycle organic waste as resource in the chemical industry; 1999 nendo chikyu kankyo sangyo gijutsu ni kakawaru sendo kenkyu seika hokokusho. Kagaku kogyo ni okeru yukisei haikibutsu no saishigenka gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    An investigational study was conducted of applicability/viability of the technology to recycle as resource the organic waste and CO2 discharged from the chemical industry, etc., and the FY 1999 results were summarized. As to the production of hydrogen from the organic waste, a bioreactor was developed which enables the production of hydrogen of 58 mmol/L/hr using Enterobactor aerogenes by the isolation bacteria method, and it successfully enabled the production of hydrogen from biomass resource. Further, the micro-flora method can be responded to a variety of substrates, but in this method the hydrogen production rate is not as high as in the isolation bacteria method at the present time. Concerning the method to convert CO2 to useful organic resource by the hydrogen produced, an experimental value of the maximum production rate of 149g/L/d which is high was obtained in case of acetic acid. Moreover, the paper described an outline and the basic concept of the recycle system of energy and carbon resource which integrates the production of energy from organic waste being considered at the present time and the production of useful matters from CO2. (NEDO)

  7. Logistic paradigm for industrial solid waste treatment processes

    Directory of Open Access Journals (Sweden)

    Janusz Grabara

    2014-12-01

    Full Text Available Due to the fact that industrial waste are a growing problem, both economic and environmental as their number is increasing every year, it is important to take measures to correctly dealing wi th industrial waste. This article presents the descriptive model of logistics processes concerning the management of industrial waste. In this model the flow of waste begins in the place of production and ends at their disposal. The article presents the concept of logistics model in graphical form together with an analysis of individual processes and their linkages, and opportunities to improve flow of industrial waste streams. Furthermore, the model allows for justification of the relevance of use logistics and its processes for waste management

  8. Long term industrial management of radioactive wastes in France

    International Nuclear Information System (INIS)

    Lavie, J.

    1981-01-01

    All human activities including energy generation entail the wastes. This definitely applies also to nuclear power generation. Currently the nuclear power program is very extensive, and the plans of fuel reprocessing proceed along this line. In consequence, the Government has decided on tackling the problem of industrial radioactive waste management in earnest. For the purpose, the National Radioactive Waste Management Agency (ANDRA) was created in November, 1979, within the French Atomic Energy Commission (CEA). Its main functions are the design, siting and construction of waste disposal centers and their management, the establishment of waste treatment and disposal standards, and the research and development. The following matters are described: the need for comprehensive industrial approach, the concept of industrial management, ANDRA business program, the industrial policy on waste disposal, and ANDRA financing. (J.P.N.)

  9. Bioprocessing applications in the management of nuclear and chemical wastes

    International Nuclear Information System (INIS)

    Genung, R.K.

    1988-01-01

    The projected requirements for waste management and environmental restoration activities within the United States will probably cost tens of billions of dollars annually during the next two decades. Expenditures of this magnitude clearly have the potential to affect the international competitiveness of many US industries and the continued operation of many federal facilities. It is argued that the costs of implementing current technology will be too high unless the standards and schedules for compliance are relaxed. Since this is socially unacceptable, efforts to improve the efficiency of existing technologies and to develop new technologies should be pursued. A sizable research, development, and demonstration effort can be easily justified if the potential for reducing costs can be shown. Bioprocessing systems for the treatment of nuclear and chemically hazardous wastes offer such promise. 11 refs

  10. Waste management in paint industries in Pakistan | Nawaz | Journal ...

    African Journals Online (AJOL)

    Chemical analyses of wastes in paint production and application have been carried out with the objective of minimizing production losses and ensuring waste management through integrated process design. The wastes contained high concentration of heavy metals, volatile organic compounds, dissolved solids and the ...

  11. Industrial waste recycling strategies optimization problem: mixed integer programming model and heuristics

    Science.gov (United States)

    Tang, Jiafu; Liu, Yang; Fung, Richard; Luo, Xinggang

    2008-12-01

    Manufacturers have a legal accountability to deal with industrial waste generated from their production processes in order to avoid pollution. Along with advances in waste recovery techniques, manufacturers may adopt various recycling strategies in dealing with industrial waste. With reuse strategies and technologies, byproducts or wastes will be returned to production processes in the iron and steel industry, and some waste can be recycled back to base material for reuse in other industries. This article focuses on a recovery strategies optimization problem for a typical class of industrial waste recycling process in order to maximize profit. There are multiple strategies for waste recycling available to generate multiple byproducts; these byproducts are then further transformed into several types of chemical products via different production patterns. A mixed integer programming model is developed to determine which recycling strategy and which production pattern should be selected with what quantity of chemical products corresponding to this strategy and pattern in order to yield maximum marginal profits. The sales profits of chemical products and the set-up costs of these strategies, patterns and operation costs of production are considered. A simulated annealing (SA) based heuristic algorithm is developed to solve the problem. Finally, an experiment is designed to verify the effectiveness and feasibility of the proposed method. By comparing a single strategy to multiple strategies in an example, it is shown that the total sales profit of chemical products can be increased by around 25% through the simultaneous use of multiple strategies. This illustrates the superiority of combinatorial multiple strategies. Furthermore, the effects of the model parameters on profit are discussed to help manufacturers organize their waste recycling network.

  12. Quantitative Characterization of Aqueous Byproducts from Hydrothermal Liquefaction of Municipal Wastes, Food Industry Wastes, and Biomass Grown on Waste

    Energy Technology Data Exchange (ETDEWEB)

    Maddi, Balakrishna; Panisko, Ellen; Wietsma, Thomas; Lemmon, Teresa; Swita, Marie; Albrecht, Karl; Howe, Daniel

    2017-01-27

    Hydrothermal liquefaction (HTL) is a viable thermochemical process for converting wet solid wastes into biocrude which can be hydroprocessed to liquid transportation fuel blendstocks and specialty chemicals. The aqueous byproduct from HTL contains significant amounts (20 to 50%) of the feed carbon, which must be used to enhance economic sustainability of the process on an industrial scale. In this study, aqueous fractions produced from HTL of industrial and municipal waste were characterized using a wide variety of analytical approaches. Organic chemical compounds present in these aqueous fractions were identified using two-dimensional gas chromatography equipped with time-of-flight mass spectrometry. Identified compounds include organic acids, nitrogen compounds, alcohols, aldehydes, and ketones. Conventional gas chromatography and liquid chromatography methods were employed to quantify the identified compounds. Inorganic species, in the aqueous stream of hydrothermal liquefaction of these aqueous byproducts, also were quantified using ion chromatography and inductively coupled plasma optical emission spectroscopy. The concentrations of organic chemical compounds and inorganic species are reported, and the significance of these results is discussed in detail.

  13. Arsenic in industrial waste water from copper production technological process

    OpenAIRE

    Biljana Jovanović; Milana Popović

    2013-01-01

    Investigation of arsenic in industrial waste water is of a great importance for environment. Discharge of untreated waste water from a copper production process results in serious pollution of surface water, which directly affects flora and fauna, as well as humans. There is a need for efficient and environmentally acceptable treament of waste waters containing heavy metals and arsenic. The paper presents an analyisis of the waste water from The Copper Smelter which is discharged into the Bor...

  14. Less is Better. Laboratory Chemical Management for Waste Reduction.

    Science.gov (United States)

    American Chemical Society, Washington, DC.

    An objective of the American Chemical Society is to promote alternatives to landfilling for the disposal of laboratory chemical wastes. One method is to reduce the amount of chemicals that become wastes. This is the basis for the "less is better" philosophy. This bulletin discusses various techniques involved in purchasing control,…

  15. Industrial waste heat utilization for low temperature district heating

    International Nuclear Information System (INIS)

    Fang, Hao; Xia, Jianjun; Zhu, Kan; Su, Yingbo; Jiang, Yi

    2013-01-01

    Large quantities of low grade waste heat are discharged into the environment, mostly via water evaporation, during industrial processes. Putting this industrial waste heat to productive use can reduce fossil fuel usage as well as CO 2 emissions and water dissipation. The purpose of this paper is to propose a holistic approach to the integrated and efficient utilization of low-grade industrial waste heat. Recovering industrial waste heat for use in district heating (DH) can increase the efficiency of the industrial sector and the DH system, in a cost-efficient way defined by the index of investment vs. carbon reduction (ICR). Furthermore, low temperature DH network greatly benefits the recovery rate of industrial waste heat. Based on data analysis and in-situ investigations, this paper discusses the potential for the implementation of such an approach in northern China, where conventional heat sources for DH are insufficient. The universal design approach to industrial-waste-heat based DH is proposed. Through a demonstration project, this approach is introduced in detail. This study finds three advantages to this approach: (1) improvement of the thermal energy efficiency of industrial factories; (2) more cost-efficient than the traditional heating mode; and (3) CO 2 and pollutant emission reduction as well as water conservation. -- Highlights: •We review situation of industrial waste heat recovery with a global perspective. •We present a way to analyze the potential to utilize industrial waste heat for DH. •Northern China has huge potential for using low-grade industrial waste heat for DH. •A demonstration project is introduced using the universal approach we propose. •It proves huge benefits for factories, heat-supply companies and the society

  16. Industrial and urban wastes in relation to Cadmium pollution

    International Nuclear Information System (INIS)

    Varavipour, M.; Akhondi, M.

    2002-01-01

    Disposal of urban, agricultural and industrial wastes is becoming a major problem in recent times. Ocean dumping, land fill applications and incineration are being considered as unsuitable. so application to agricultural lands is being increasingly used for this purpose. Application of wastes to soils can be beneficial in providing plant nutrients and organic matter. But, it also leads to harmful effects like introduction of heavy metals, toxic organics, danger of ground water pollution, etc. Cadmium buildup in soil and absorption into plants and then entering into food chain due to these wastes is of concern because of its higher mobility than most other heavy metals. Although discontinuation of sewage sludge disposal on crop land would stop further soil contamination, potential danger from metal accumulation by crops grown after termination of the practice is still a concern. Trace metals are relatively immobile in soil. Therefore, depending on biological and chemical equilibria established following terminal sludge application, sludge-borne Cd might change in plant availability with time

  17. Vacuum technology in the chemical industry

    CERN Document Server

    Jorisch, Wolfgang

    2015-01-01

    Based on the very successful German edition and a seminar held by the German Engineers` Association (VDI) on a regular basis for years now, this English edition has been thoroughly updated and revised to reflect the latest developments. It supplies in particular the special aspects of vacuum technology, applied vacuum pump types and vacuum engineering in the chemical, pharmaceutical and process industry application-segments. The text includes chapters dedicated to latest European regulations for operating in hazardous zones with vacuum systems, methods for process pressure control and regulati

  18. A new procedure for the treatment of an industrial waste containing flotation reagents

    Directory of Open Access Journals (Sweden)

    Milosavljević Milutin M.

    2014-01-01

    Full Text Available Flotation reagents can be transformed to industrial waste if they are stored for a long period of time. Also, if synthesis or drying process is not performed under defined conditions in industrial plants, which produce flotation reagents, batch of waste may arise and be stored as a waste. The chemical composition of this waste depends on the phase in which it was created, but typically includes: unreacted alkali hydroxide, solvent - alcohol and trithiocarbonate and oxidation product - dixanthogenate. In this paper a new laboratory procedure for the treatment of such wastes is described. The identification and separation of industrial waste components is also included. From the separated dixantogenate and xanthate a laboratory synthesis of thioncarbamates is given. In addition, a semi-industrial treatment of waste xanthate is presented. Synthesis of N-alkyl and N,N-dialkyl-O-isobutylthioncarbamates were obtained from the filtrate obtained in the first step. As a by-product, sodium thioglycolate was produced. This by-product is transformed to a thioglycolic acid by the addition of an acid. Also, the synthesis of thioncarbamates from dixanthogenates, isolated from industrial waste as a cake, is desribed. Described waste treatment is additionally interesting due to the production of sulphur as another by-product. Laboratory synthesis gave thioncarbamates in yields from 69.7 to 87.7 %, while the semi-industrial process for the selected batches produced thioncarbamates in yields from 74.2 to 80.5 %. Taking into account the importance of the synthesized compounds as selective flotation reagents, a new procedure of their synthesis from industrial waste is characterized by good yields and purity of the obtained compounds, the simplicity of process, low environmental impact and short reaction times of synthesis. [Projekat Ministarstva nauke Republike Srbije, br. III 43007

  19. Prospects for pyrolysis technologies in managing municipal, industrial, and DOE cleanup wastes

    Energy Technology Data Exchange (ETDEWEB)

    Reaven, S.J. [State Univ. of New York, Stony Brook, NY (United States)

    1994-12-01

    Pyrolysis converts portions of municipal solid wastes, hazardous wastes, and special wastes such as tires, medical wastes, and even old landfills into solid carbon and a liquid or gaseous hydrocarbon stream. Pyrolysis heats a carbonaceous waste stream typically to 290--900 C in the absence of oxygen, and reduces the volume of waste by 90% and its weight by 75%. The solid carbon char has existing markets as an ingredient in many manufactured goods, and as an adsorbent or filter to sequester certain hazardous wastes. Pyrolytic gases may be burned as fuel by utilities, or liquefied for use as chemical feedstocks, or low-pollution motor vehicle fuels and fuel additives. This report analyzes the potential applications of pyrolysis in the Long Island region and evaluates for the four most promising pyrolytic systems their technological and commercial readiness, their applicability to regional waste management needs, and their conformity with DOE requirements for environmental restoration and waste management. This summary characterizes their engineering performance, environmental effects, costs, product applications, and markets. Because it can effectively treat those wastes that are inadequately addressed by current systems, pyrolysis can play an important complementing role in the region`s existing waste management strategy. Its role could be even more significant if the region moves away from existing commitments to incineration and MSW composting. Either way, Long Island could become the center for a pyrolysis-based recovery services industry serving global markets in municipal solid waste treatment and hazardous waste cleanup. 162 refs.

  20. Prospects for pyrolysis technologies in managing municipal, industrial, and DOE cleanup wastes

    International Nuclear Information System (INIS)

    Reaven, S.J.

    1994-12-01

    Pyrolysis converts portions of municipal solid wastes, hazardous wastes, and special wastes such as tires, medical wastes, and even old landfills into solid carbon and a liquid or gaseous hydrocarbon stream. Pyrolysis heats a carbonaceous waste stream typically to 290--900 C in the absence of oxygen, and reduces the volume of waste by 90% and its weight by 75%. The solid carbon char has existing markets as an ingredient in many manufactured goods, and as an adsorbent or filter to sequester certain hazardous wastes. Pyrolytic gases may be burned as fuel by utilities, or liquefied for use as chemical feedstocks, or low-pollution motor vehicle fuels and fuel additives. This report analyzes the potential applications of pyrolysis in the Long Island region and evaluates for the four most promising pyrolytic systems their technological and commercial readiness, their applicability to regional waste management needs, and their conformity with DOE requirements for environmental restoration and waste management. This summary characterizes their engineering performance, environmental effects, costs, product applications, and markets. Because it can effectively treat those wastes that are inadequately addressed by current systems, pyrolysis can play an important complementing role in the region's existing waste management strategy. Its role could be even more significant if the region moves away from existing commitments to incineration and MSW composting. Either way, Long Island could become the center for a pyrolysis-based recovery services industry serving global markets in municipal solid waste treatment and hazardous waste cleanup. 162 refs

  1. Six Strategies for Chemical Waste Minimization in Laboratories.

    Science.gov (United States)

    Matteson, Gary C.; Hadley, Cheri R.

    1991-01-01

    Guidelines are offered to research administrators for reducing the volume of hazardous laboratory waste. Suggestions include a chemical location inventory, a chemical reuse facility, progressive contracts with chemical suppliers, internal or external chemical recycling mechanisms, a "chemical conservation" campaign, and laboratory fees for…

  2. Potential of waste heat in Croatian industrial sector

    Directory of Open Access Journals (Sweden)

    Bišćan Davor

    2012-01-01

    Full Text Available Waste heat recovery in Croatian industry is of the highest significance regarding the national efforts towards energy efficiency improvements and climate protection. By recuperation of heat which would otherwise be wasted, the quantity of fossil fuels used for production of useful energy could be lowered thereby reducing the fuel costs and increasing the competitiveness of examined Croatian industries. Another effect of increased energy efficiency of industrial processes and plants is reduction of greenhouse gases i.e. the second important national goal required by the European Union (EU and United Nations Framework Convention on Climate Change (UNFCCC. Paper investigates and analyses the waste heat potential in Croatian industrial sector. Firstly, relevant industrial sectors with significant amount of waste heat are determined. Furthermore, significant companies in these sectors are selected with respect to main process characteristics, operation mode and estimated waste heat potential. Data collection of waste heat parameters (temperature, mass flow and composition is conducted. Current technologies used for waste heat utilization from different waste heat sources are pointed out. Considered facilities are compared with regard to amount of flue gas heat. Mechanisms for more efficient and more economic utilization of waste heat are proposed. [Acknoledgment. The authors would like to acknowledge the financial support provided by the UNITY THROUGH KNOWLEDGE FUND (UKF of the Ministry of Science, Education and Sports of the Republic of Croatia and the World Bank, under the Grant Agreement No. 89/11.

  3. Principles of development of the industry of technogenic waste processing

    Directory of Open Access Journals (Sweden)

    Maria A. Bayeva

    2014-01-01

    Full Text Available Objective to identify and substantiate the principles of development of the industry of technogenic waste processing. Methods systemic analysis and synthesis method of analogy. Results basing on the analysis of the Russian and foreign experience in the field of waste management and environmental protection the basic principles of development activities on technogenic waste processing are formulated the principle of legal regulation the principle of efficiency technologies the principle of ecological safety the principle of economic support. The importance of each principle is substantiated by the description of the situation in this area identifying the main problems and ways of their solution. Scientific novelty the fundamental principles of development of the industry of the industrial wastes processing are revealed the measures of state support are proposed. Practical value the presented theoretical conclusions and proposals are aimed primarily on theoretical and methodological substantiation and practical solutions to modern problems in the sphere of development of the industry of technogenic waste processing.

  4. Physico chemical evaluation of coffee husk, wastes of enset (Enset ...

    African Journals Online (AJOL)

    Physico chemical evaluation of coffee husk, wastes of enset (Enset ventricosum), vegetable and khat (Catha edulis) through vermicomposting employing an epigeic earthworm Dendrobaena veneta (Rosa, 1886)

  5. Measurements and models for hazardous chemical and mixed wastes. 1998 annual progress report

    International Nuclear Information System (INIS)

    Holcomb, C.; Louie, B.; Mullins, M.E.; Outcalt, S.L.; Rogers, T.N.; Watts, L.

    1998-01-01

    'Aqueous waste of various chemical compositions constitutes a significant fraction of the total waste produced by industry in the US. A large quantity of the waste generated by the US chemical process industry is waste water. In addition, the majority of the waste inventory at DoE sites previously used for nuclear weapons production is aqueous waste. Large quantities of additional aqueous waste are expected to be generated during the clean-up of those sites. In order to effectively treat, safely handle, and properly dispose of these wastes, accurate and comprehensive knowledge of basic thermophysical property information is paramount. This knowledge will lead to huge savings by aiding in the design and optimization of treatment and disposal processes. The main objectives of this project are: Develop and validate models that accurately predict the phase equilibria and thermodynamic properties of hazardous aqueous systems necessary for the safe handling and successful design of separation and treatment processes for hazardous chemical and mixed wastes. Accurately measure the phase equilibria and thermodynamic properties of a representative system (water + acetone + isopropyl alcohol + sodium nitrate) over the applicable ranges of temperature, pressure, and composition to provide the pure component, binary, ternary, and quaternary experimental data required for model development. As of May, 1998, nine months into the first year of a three year project, the authors have made significant progress in the database development, have begun testing the models, and have been performance testing the apparatus on the pure components.'

  6. Economic analysis of waste-to-energy industry in China.

    Science.gov (United States)

    Zhao, Xin-Gang; Jiang, Gui-Wu; Li, Ang; Wang, Ling

    2016-02-01

    The generation of municipal solid waste is further increasing in China with urbanization and improvement of living standards. The "12th five-year plan" period (2011-2015) promotes waste-to-energy technologies for the harmless disposal and recycling of municipal solid waste. Waste-to-energy plant plays an important role for reaching China's energy conservation and emission reduction targets. Industrial policies and market prospect of waste-to-energy industry are described. Technology, cost and benefit of waste-to-energy plant are also discussed. Based on an economic analysis of a waste-to-energy project in China (Return on Investment, Net Present Value, Internal Rate of Return, and Sensitivity Analysis) the paper makes the conclusions. Copyright © 2015 Elsevier Ltd. All rights reserved.

  7. 2016 Annual Industrial Wastewater Reuse Report for the Idaho National Laboratory Site’s Materials and Fuels Complex Industrial Waste Ditch and Industrial Waste Pond

    Energy Technology Data Exchange (ETDEWEB)

    Cafferty, Kara Grace [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2017-02-01

    This report describes conditions, as required by the state of Idaho Industrial Wastewater Reuse Permit (WRU-I-0160-01, Modification 1, formerly LA 000160 01), for the wastewater reuse site at the Idaho National Laboratory Site’s Materials and Fuels Complex Industrial Waste Ditch and Industrial Waste Pond from November 1, 2015, through October 31, 2016.

  8. 2016 Annual Industrial Wastewater Reuse Report for the Idaho National Laboratory Site's Materials and Fuels Complex Industrial Waste Ditch and Industrial Waste Pond

    International Nuclear Information System (INIS)

    Cafferty, Kara Grace

    2017-01-01

    This report describes conditions, as required by the state of Idaho Industrial Wastewater Reuse Permit (WRU-I-0160-01, Modification 1, formerly LA 000160 01), for the wastewater reuse site at the Idaho National Laboratory Site's Materials and Fuels Complex Industrial Waste Ditch and Industrial Waste Pond from November 1, 2015, through October 31, 2016.

  9. Use of some industrial waste as energy storage media

    International Nuclear Information System (INIS)

    Tayeb, A.M.

    1996-01-01

    Solar energy is stored using different solid storage materials, both chemical and metallic industrial wastes. The materials tested in the present study are paraffin wax, copper slag, aluminium slag, iron slag, cast iron slag and copper chips. Solar energy is stored in these materials and energy ia then recovered with water stream at different flow rates and the storage capacity and period for different materials were compared. The same set of experiments is run on solid metallic materials mixed with wax. The results indicated that iron slag has the highest storage capacity followed by cast iron slag then aluminium slag and copper chips and copper slag. It is also noted that addition of paraffin wax to the solid metallic material improves its storage capacity and duration greatly. The storage efficiency of different units is calculated and compared. 5 figs

  10. 40 CFR 268.36 - Waste specific prohibitions-inorganic chemical wastes

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Waste specific prohibitions-inorganic chemical wastes 268.36 Section 268.36 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... generator may use knowledge of the waste. If the waste contains regulated constituents in excess of the...

  11. Optimal waste heat recovery and reuse in industrial zones

    International Nuclear Information System (INIS)

    Stijepovic, Mirko Z.; Linke, Patrick

    2011-01-01

    Significant energy efficiency gains in zones with concentrated activity from energy intensive industries can often be achieved by recovering and reusing waste heat between processing plants. We present a systematic approach to target waste heat recovery potentials and design optimal reuse options across plants in industrial zones. The approach first establishes available waste heat qualities and reuse feasibilities considering distances between individual plants. A targeting optimization problem is solved to establish the maximum possible waste heat recovery for the industrial zone. Then, a design optimization problem is solved to identify concrete waste heat recovery options considering economic objectives. The paper describes the approach and illustrates its application with a case study. -- Highlights: → Developed a systematic approach to target waste heat recovery potentials and to design optimal recovery and reuse options across plants in industrial zones. → Five stage approach involving data acquisition, analysis, assessment, targeting and design. → Targeting optimization problem establishes the maximum possible waste heat recovery and reuse limit for the industrial zone. → Design optimization problem provides concrete waste heat recovery and reuse network design options considering economic objectives.

  12. Environmental and Human Health Impacts of Usage of Oil Industry Products and Wastes as Alternative Fuel

    Directory of Open Access Journals (Sweden)

    Dilek BOLAT

    2016-03-01

    Full Text Available The need for oil industry products has been increasing in parallel to the rapid population growth and industrialization. Physical and chemical properties of these products change after usage based on the media and operating conditions. Then, these products lose the eligibility and turn into the form of waste. The most commonly used method for the disposal of waste oils is combustion due to its high calorific value. In this study, the possible effects on the environment and human health of combustion of oil industry products and wastes are evaluated. Poor combustion conditions lead emissions from the process depending on the ingredients of wastes in addition to incomplete combustion products such as particulate matter, carbon monoxide, volatile organic chemicals polyaromatic hydrocarbons, metals etc. that may occur according to the type of waste. These emissions are released into the environment and partition between soil, water and air media related to their physicochemical characteristics. In addition to environmental problems, these emissions are a risk factor for human health in terms of carcinogenicity and mutagenicity. Regulations and control measures should be put into practice in order to get rid of the effects of non-standard diesel like product named number 10 lube on human health and environment. In this context, emission measurements should be done simultaneously to determine the effects of combustion of these wastes and products of oil industry.

  13. Citric waste saccharification under different chemical treatments

    Directory of Open Access Journals (Sweden)

    Carlos Eduardo de Farias Silva

    2015-10-01

    Full Text Available Second generation ethanol from lignocellulose materials has been used in applications for food processing wastes. Since Brazil has a leading position in orange juice exports, the influence of acid and alkali pretreatments on liquor saccharification, solubilization of solid fraction and mass yield was evaluated. Time and Cacid or Calkaline at different concentrations of solids (low to moderate, 1 to 9% and high catalyst concentrations were analyzed. A hydrothermal pretreatment was conducted under the same conditions of acid and alkaline treatments to investigate the relative selectivity increase in using the catalysts. The chemical analyses of wastes indicated a 70% total carbohydrate level denoting a promising raw material for bioethanol production. Pretreatment caused acid saccharifications between 25 and 65% in total reducing sugars (TRS and mass yields (MY between 30 and 40%. In alkaline pretreatment, these rates ranged between 2 and 22.5% and between 30 and 80, respectively. In hydrothermal pretreatment, solubilized TRS varied between 3 and 37%, whereas MY remained between 45 and 60%, respectively. Cbiomass strongly influenced the three variables; in the same way, time affected MY.

  14. Arsenic in industrial waste water from copper production technological process

    Directory of Open Access Journals (Sweden)

    Biljana Jovanović

    2013-12-01

    Full Text Available Investigation of arsenic in industrial waste water is of a great importance for environment. Discharge of untreated waste water from a copper production process results in serious pollution of surface water, which directly affects flora and fauna, as well as humans. There is a need for efficient and environmentally acceptable treament of waste waters containing heavy metals and arsenic. The paper presents an analyisis of the waste water from The Copper Smelter which is discharged into the Bor river. The expected arsenic content in treated waste water after using HDS procedure is also presented.

  15. Blasting at a Superfund chemical waste site

    International Nuclear Information System (INIS)

    Burns, D.R.

    1991-01-01

    During the summer of 1989, Maine Drilling and Blasting of Gardiner, Maine was contracted by Cayer Corporation of Harvard, Massachusetts to drill and blast an interceptor trench at the Nyanza Chemical Superfund Site in Ashland, Massachusetts. The interceptor trench was to be 1,365 feet long and to be blasted out of granite. The trench was to be 12 feet wide at the bottom with 1/1 slopes, the deepest cut being 30 feet deep. A French drain 12 feet wide by 15 to 35 feet deep was blasted below the main trench on a 2% slope from its center to each end. A French drain is an excavation where the rock is blasted but not dug. The trench would be used as a perimeter road with any ground water flow going through the French drain flowing to both ends of the trench. Being a Superfund project turned a simple blasting project into a regulatory nightmare. The US Environmental Protection Agency performed all the chemical related functions on site. The US Army Corps of Engineers was overseeing all related excavation and construction on site, as was the Massachusetts Department of Environmental Quality Engineering, the local Hazardous Wastes Council, and the local Fire Department. All parties had some input with the blasting and all issues had to be addressed. The paper outlines the project, how it was designed and completed. Also included is an outline of the blast plan to be submitted for approval, an outline of the Safety/Hazardous Waste training and a description of all the problems which arose during the project by various regulatory agencies

  16. Microbial keratinases: industrial enzymes with waste management potential.

    Science.gov (United States)

    Verma, Amit; Singh, Hukum; Anwar, Shahbaz; Chattopadhyay, Anirudha; Tiwari, Kapil K; Kaur, Surinder; Dhilon, Gurpreet Singh

    2017-06-01

    Proteases are ubiquitous enzymes that occur in various biological systems ranging from microorganisms to higher organisms. Microbial proteases are largely utilized in various established industrial processes. Despite their numerous industrial applications, they are not efficient in hydrolysis of recalcitrant, protein-rich keratinous wastes which result in environmental pollution and health hazards. This paved the way for the search of keratinolytic microorganisms having the ability to hydrolyze "hard to degrade" keratinous wastes. This new class of proteases is known as "keratinases". Due to their specificity, keratinases have an advantage over normal proteases and have replaced them in many industrial applications, such as nematicidal agents, nitrogenous fertilizer production from keratinous waste, animal feed and biofuel production. Keratinases have also replaced the normal proteases in the leather industry and detergent additive application due to their better performance. They have also been proved efficient in prion protein degradation. Above all, one of the major hurdles of enzyme industrial applications (cost effective production) can be achieved by using keratinous waste biomass, such as chicken feathers and hairs as fermentation substrate. Use of these low cost waste materials serves dual purposes: to reduce the fermentation cost for enzyme production as well as reducing the environmental waste load. The advent of keratinases has given new direction for waste management with industrial applications giving rise to green technology for sustainable development.

  17. Deep Eutectic Solvents pretreatment of agro-industrial food waste.

    Science.gov (United States)

    Procentese, Alessandra; Raganati, Francesca; Olivieri, Giuseppe; Russo, Maria Elena; Rehmann, Lars; Marzocchella, Antonio

    2018-01-01

    Waste biomass from agro-food industries are a reliable and readily exploitable resource. From the circular economy point of view, direct residues from these industries exploited for production of fuel/chemicals is a winning issue, because it reduces the environmental/cost impact and improves the eco-sustainability of productions. The present paper reports recent results of deep eutectic solvent (DES) pretreatment on a selected group of the agro-industrial food wastes (AFWs) produced in Europe. In particular, apple residues, potato peels, coffee silverskin, and brewer's spent grains were pretreated with two DESs, (choline chloride-glycerol and choline chloride-ethylene glycol) for fermentable sugar production. Pretreated biomass was enzymatic digested by commercial enzymes to produce fermentable sugars. Operating conditions of the DES pretreatment were changed in wide intervals. The solid to solvent ratio ranged between 1:8 and 1:32, and the temperature between 60 and 150 °C. The DES reaction time was set at 3 h. Optimal operating conditions were: 3 h pretreatment with choline chloride-glycerol at 1:16 biomass to solvent ratio and 115 °C. Moreover, to assess the expected European amount of fermentable sugars from the investigated AFWs, a market analysis was carried out. The overall sugar production was about 217 kt yr -1 , whose main fraction was from the hydrolysis of BSGs pretreated with choline chloride-glycerol DES at the optimal conditions. The reported results boost deep investigation on lignocellulosic biomass using DES. This investigated new class of solvents is easy to prepare, biodegradable and cheaper than ionic liquid. Moreover, they reported good results in terms of sugars' release at mild operating conditions (time, temperature and pressure).

  18. Industrial waste needs assessment. Phase 1

    Energy Technology Data Exchange (ETDEWEB)

    Radel, R.J.; Willis, M.P. [eds.

    1993-10-01

    In January of 1992 a team was put together to begin the process of assessing the industrial waste needs of the Tennessee Valley. The team consisted of representatives from the various TVA Resource Group organizations. This initial team recommended as a starting point in the process a two-phase market research effort. A second team was then commissioned to conduct the first phase of this market research effort. The first phase of that marketing effort is now complete. This report contains an analysis of the data obtained through interviews of more than 168 individuals representing a similar number of organizations. A total of 37 TVA Resource Group employees were involved in the contact process from various organizations. In addition, the appendices provide summaries of the data used in designing the process and the reports of the Contact Coordinators (who were responsible for a series of visits). As a result of the data analysis, the Review Team makes the following recommendations: 1. Publish this report and distribute to the new management within TVA Resource Group as well as to all those participating as contacts, visitors, and contact coordinators. 2. The Resource Group management team, or management teams within each of the respective organizations within Resource Group, appoint Phase 2 assessement teams for as many of the problem areas listed in Table III as seem appropriate. We further recommend that, where possible, cross-organizational teams be used to examine individual problem areas. 3. Make this report available within Generating and Customer Groups, especially to the Customer Service Centers. 4. Establish a process to continue follow up with each of the contacts made in this assessment.

  19. Industrial waste needs assessment. Phase 1

    International Nuclear Information System (INIS)

    Radel, R.J.; Willis, M.P.

    1993-10-01

    In January of 1992 a team was put together to begin the process of assessing the industrial waste needs of the Tennessee Valley. The team consisted of representatives from the various TVA Resource Group organizations. This initial team recommended as a starting point in the process a two-phase market research effort. A second team was then commissioned to conduct the first phase of this market research effort. The first phase of that marketing effort is now complete. This report contains an analysis of the data obtained through interviews of more than 168 individuals representing a similar number of organizations. A total of 37 TVA Resource Group employees were involved in the contact process from various organizations. In addition, the appendices provide summaries of the data used in designing the process and the reports of the Contact Coordinators (who were responsible for a series of visits). As a result of the data analysis, the Review Team makes the following recommendations: 1. Publish this report and distribute to the new management within TVA Resource Group as well as to all those participating as contacts, visitors, and contact coordinators. 2. The Resource Group management team, or management teams within each of the respective organizations within Resource Group, appoint Phase 2 assessement teams for as many of the problem areas listed in Table III as seem appropriate. We further recommend that, where possible, cross-organizational teams be used to examine individual problem areas. 3. Make this report available within Generating and Customer Groups, especially to the Customer Service Centers. 4. Establish a process to continue follow up with each of the contacts made in this assessment

  20. APPLICATION OF CHEMICAL METHODS TO THE SOLID WASTE MANAGEMENT

    Directory of Open Access Journals (Sweden)

    C. P. Bulimaga

    2008-12-01

    Full Text Available The present article is a synthesis analysis of application of chemical methods for the development of technologies of hazardous waste management. Here are offered some technologies of neutralization of the waste containing hexacyanofferates, galvanic wastes and those with contain of vanadium, which are collected at Power Thermoelectric Plants.

  1. Defusing the Toxics Threat: Controlling Pesticides and Industrial Waste. Worldwatch Paper 79.

    Science.gov (United States)

    Postel, Sandra

    The use of pesticides in agriculture and the discarding of industrial chemical waste into the air, soil, and water constitute two major pathways of human exposure to toxic substances. It is argued that these practices release hundreds of millions of tons of potentially hazardous substances into the environment each year. Speculation continues into…

  2. Characterization of radioactive mixed wastes: The industrial perspective

    International Nuclear Information System (INIS)

    Leasure, C.S.

    1992-01-01

    Physical and chemical characterization of Radioactive Mixed Wastes (RMW) is necessary for determination of appropriate treatment options and to satisfy environmental regulations. Radioactive mixed waste can be classified as two main categories; contact-handled (low level) RMW and remote-handled RMW. Ibis discussion will focus mainly on characterization of contact handled RMW. The characterization of wastes usually follows one of two pathways: (1) characterization to determine necessary parameters for treatment or (2) characterization to determine if the material is a hazardous waste. Sometimes, however, wastes can be declared as hazardous waste without testing and then treated as hazardous waste. Characterization of radioactive mixed wastes pose some unique issues, however, that will require special solutions. Below, five issues affecting sampling and analysis of RMW will be discussed

  3. Chemical activation of tea waste and use for the removal of chromium (Vi) from aqueous solution

    International Nuclear Information System (INIS)

    Qureshi, K.; Bhatti, I.; Ansari, A.K.

    2009-01-01

    Tea waste is the residue left after the preparation of tea. At present the tea waste is regarded as a waste product having no use. In this study, tea waste is converted into an adsorbent. Tea waste is chemically activated with phosphoric acid at low temperature 450 degree C. This activated carbon is then utilized as an adsorbent for the removal of Chromium (VI) from aqueous solution. The various sorption parameters i.e pH, sorbent dose sorbate concentration, shaking time and shaking speed are first optimized. 75% of chromium from aqueous solution is effectively removed at pH 2. The best optimum conditions were obtained when 1 gm of sorbent was agitated at 100 rpm with 60 mg/l of sorbate for 50 minutes. Better results were obtained when low concentrations of sorbates were used. Hence tea waste could also be successfully used for the sorption of Chromium (VI), from industrial waste water. (author)

  4. Radiation purification of the chemical industry effluents and possibilities of realization of this method

    International Nuclear Information System (INIS)

    Petryaev, E.P.; Kovalevskaya, A.M.; Shlyk, V.G.; Savushkin, I.A.; Kazazyan, V.T.

    1977-01-01

    Radiation-chemical methods for synthetic fibre industry effluents purification from cyanides, sulphides and monomers, as well as for disinfection of circulation water and improvement in sedimental and filtering properties of waste active slurry in petrochemical industry are described. Chemical plant effluents are purified by 70-90% from cyanides at the dose rate of 0,3 - 0,5 Mrad, by 60 - 70% from sulphides and monomers at the dose of 0,2 Mrad. Circulation water of petroleum processing plant is disinfected at the dose of 0,08 Mrad; the rates of filtration and sedimentation of waste active slurry increase two and three fold, correspondingly, at the dose of 0,6 Mrad. The power of radiation sources required for the industrial realization of radiation purification of liquid wastes has been calculated

  5. Carbon source in the future chemical industries

    Science.gov (United States)

    Hofmann, Peter; Heinrich Krauch, Carl

    1982-11-01

    Rising crude oil prices favour the exploitation of hitherto unutilised energy carriers and the realisation of new technologies in all sectors where carbon is used. These changed economic constraints necessitate both savings in conventional petrochemistry and a change to oil-independent carbon sources in the chemical industry. While, in coal chemistry, the synthesis and process principles of petrochemistry — fragmentation of the raw material and subsequent buildup of molecular structures — can be maintained, the raw material structure largely remains unchanged in the chemistry of renewable raw materials. This lecture is to demonstrate the structural as well as the technological and energy criteria of the chemistry of alternative carbon sources, to forecast the chances of commercial realization and to discuss some promising fields of research and development.

  6. Ultrasonic filtration of industrial chemical solutions

    Science.gov (United States)

    Cosma, T.

    1974-01-01

    The practical results obtained as a result of filtering industrial chemical solutions under continuous flow conditions with the aid of an ultrasonic filter are presented. The main part of the assembly consists of an ultrasonic generator with an output power of about 400 W and the filtration assembly, in which there is a magnetostrictive amplifier constructed for 20.5 kHz. In addition to ensuring a continuous flow of filtered solution, ultrasonic filters can be replaced or cleaned at intervals of time that are 8-10 times greater than in the case of mechanical filters. They yield considerably better results as far as the size of the filtered particles is concerned. The parameters on which filtration quality depends are also presented.

  7. Factors influencing chemical durability of nuclear waste glasses

    International Nuclear Information System (INIS)

    Feng, Xiangdong; Bates, J.K.

    1993-01-01

    A short summary is given of our studies on the major factors that affect the chemical durability of nuclear waste glasses. These factors include glass composition, solution composition, SA/V (ratio of glass surface area to the volume of solution), radiation, and colloidal formation. These investigations have enabled us to gain a better understanding of the chemical durability of nuclear waste glasses and to accumulate.a data base for modeling the long-term durability of waste glass, which will be used in the risk assessment of nuclear waste disposal. This knowledge gained also enhances our ability to formulate optimal waste glass compositions

  8. Analytical methods for waste minimisation in the convenience food industry.

    Science.gov (United States)

    Darlington, R; Staikos, T; Rahimifard, S

    2009-04-01

    Waste creation in some sectors of the food industry is substantial, and while much of the used material is non-hazardous and biodegradable, it is often poorly dealt with and simply sent to landfill mixed with other types of waste. In this context, overproduction wastes were found in a number of cases to account for 20-40% of the material wastes generated by convenience food manufacturers (such as ready-meals and sandwiches), often simply just to meet the challenging demands placed on the manufacturer due to the short order reaction time provided by the supermarkets. Identifying specific classes of waste helps to minimise their creation, through consideration of what the materials constitute and why they were generated. This paper aims to provide means by which food industry wastes can be identified, and demonstrate these mechanisms through a practical example. The research reported in this paper investigated the various categories of waste and generated three analytical methods for the support of waste minimisation activities by food manufacturers. The waste classifications and analyses are intended to complement existing waste minimisation approaches and are described through consideration of a case study convenience food manufacturer that realised significant financial savings through waste measurement, analysis and reduction.

  9. Assessment of waste management in a brewing industry in Nigeria ...

    African Journals Online (AJOL)

    International Journal of Natural and Applied Sciences ... in the generation of offensive by – products in terms of industrial wastes in our environment. ... The obtained values were compared with the Federal Environmental Protection Agency ...

  10. Principles for disposal of radioactive and chemical hazardous wastes

    International Nuclear Information System (INIS)

    Merz, E. R.

    1991-01-01

    The double hazard of mixed wastes is characterized by several criteria: radioactivity on the one hand, and chemical toxicity, flammability, corrosiveness as well as chemical reactivity on the other hand. Chemotoxic waste normally has a much more complex composition than radioactive waste and appears in much larger quantities. However, the two types of waste have some properties in common when it comes to their long-term impact on health and the environment. In order to minimize the risk associated with mixed waste management, the material assigned for ultimate disposal should be thoroughly detoxified, inertized, or mineralized prior to conditioning and packaging. Good control over the environmental consequence of waste disposal requires that detailed criteria for tolerable contamination should be established, and that compliance with these criteria can be demonstrated. For radioactive waste, there has been an extensive international development of criteria to protect human health. For non-radioactive waste, derived criteria exist only for a limited number of substances

  11. Estimation of Pb from metal and electroplating industrial waste by ...

    African Journals Online (AJOL)

    The concentration of lead in sediment and liquid waste samples of selected metal electroplating industries was measured by atomic absorption spectrophotometer. The data obtained revealed that lead content in liquid wastes varies in the range of 0.582-14.97 mg L-1 and 1.300-757.8 mg Kg-1 in sediments. Removal of ...

  12. The radioactive wastes management of the little nuclear industry

    International Nuclear Information System (INIS)

    2008-01-01

    Among the ANDRA customers, more than one million are little producers: hospital, research centers and industries. They are called little producers because of the low volume of produced wastes. Meanwhile these wastes management need an appropriate technology which is presented in this document. (A.L.B.)

  13. Methods for waste waters treatment in textile industry

    OpenAIRE

    Srebrenkoska, Vineta; Zhezhova, Silvana; Risteski, Sanja; Golomeova, Saska

    2014-01-01

    The processes of production of textiles or wet treatments and finishing processes of textile materials are huge consumers of water with high quality. As a result of these various processes, considerable amounts of polluted water are released. This paper puts emphasis on the problem of environmental protection against waste waters generated by textile industry. The methods of pretreatment or purification of waste waters in the textile industry can be: Primary (screening, sedimentation, homo...

  14. Low carbon fuel and chemical production from waste gases

    Energy Technology Data Exchange (ETDEWEB)

    Simpson, S.; Liew, F.M.; Daniell, J.; Koepke, M. [LanzaTech, Ltd., Auckland (New Zealand)

    2012-07-01

    LanzaTech has developed a gas fermentation platform for the production of alter native transport fuels and commodity chemicals from carbon monoxide, hydrogen and carbon dioxide containing gases. LanzaTech technology uses these gases in place of sugars as the carbon and energy source for fermentation thereby allowing a broad spectrum of resources to be considered as an input for product synthesis. At the core of the Lanzatech process is a proprietary microbe capable of using gases as the only carbon and energy input for product synthesis. To harness this capability for the manufacture of a diverse range of commercially valuable products, the company has developed a robust synthetic biology platform to enable a variety of novel molecules to be synthesised via gas fermentation. LanzaTech initially focused on the fermentation of industrial waste gases for fuel ethanol production. The company has been operating pilot plant that uses direct feeds of steel making off gas for ethanol production for over 24 months. This platform technology has been further successfully demonstrated using a broad range of gas inputs including gasified biomass and reformed natural gas. LanzaTech has developed the fermentation, engineering and control systems necessary to efficiently convert gases to valuable products. A precommercial demonstration scale unit processing steel mill waste gases was commissioned in China during the 2{sup nd} quarter of 2012. Subsequent scale-up of this facility is projected for the 2013 and will represent the first world scale non-food based low carbon ethanol project. More recently LanzaTech has developed proprietary microbial catalysts capable of converting carbon dioxide in the presence of hydrogen directly to value added chemicals, where-in CO{sub 2} is the sole source of carbon for product synthesis. Integrating the LanzaTech technology into a number of industrial facilities, such as steel mills, oil refineries and other industries that emit Carbon bearing

  15. Solid industrial wastes and their management in Asegra (Granada, Spain)

    International Nuclear Information System (INIS)

    Casares, M.L.; Ulierte, N.; Mataran, A.; Ramos, A.; Zamorano, M.

    2005-01-01

    ASEGRA is an industrial area in Granada (Spain) with important waste management problems. In order to properly manage and control waste production in industry, one must know the quantity, type, and composition of industrial wastes, as well as the management practices of the companies involved. In our study, questionnaires were used to collect data regarding methods of waste management used in 170 of the 230 businesses in the area of study. The majority of these companies in ASEGRA are small or medium-size, and belong to the service sector, transport, and distribution. This was naturally a conditioning factor in both the type and management of the wastes generated. It was observed that paper and cardboard, plastic, wood, and metals were the most common types of waste, mainly generated from packaging (49% of the total volume), as well as material used in containers and for wrapping products. Serious problems were observed in the management of these wastes. In most cases they were disposed of by dumping, and very rarely did businesses resort to reuse, recycling or valorization. Smaller companies encountered greater difficulties when it came to effective waste management. The most frequent solution for the disposal of wastes in the area was dumping

  16. Performance of evaporators in high level radioactive chemical waste service

    International Nuclear Information System (INIS)

    Jenkins, C.F.

    1997-01-01

    Chemical processing of nuclear fuels and targets at Savannah River Site resulted in generation of millions of gallons of liquid wastes. The wastes were further processed to reduce volume and allow for extended temporary storage of a more concentrated material. Waste evaporators have been a central point for waste reduction for many years. Currently, the transfer and processing of the concentrated wastes for permanent storage requires dilution and results in generation of significant quantities of additional liquid wastes. A new round of volume reduction is required to fit existing storage capacity and to allow for removal of older vessels from service. Evaporator design, performance and repairs are discussed in this report

  17. IDENTIFICATION AND CLASSIFICATION OF INDUSTRIAL SOLID WASTES IN AMMONIA UNIT OF RAZI PETROCHEMICAL COMPLEX AND FEASIBILITY OF WASTE MINIMIZATION

    Directory of Open Access Journals (Sweden)

    F. Fakheri Raouf, R. Nabizadeh and N. Jafarzadeh

    2005-10-01

    Full Text Available Petrochemical industries are considered as strategic and important sectors in economic development of Iran. Razi petrochemical factory is one of complex in Iran, established in 1970 with 100 hectare. In this research, the possibility of waste minimization in the ammonia unit of Razi petrochemical complex with about 1000 tons per year was studied for a period of 18 months from September 2003 to April 2005. More than 20 site visits were conducted and the required information was collected. Factors such as industrial solid wastes quality and quantity, sources of generation, production period and the present management practice, were studied. Petrochemical solid wastes were classified based on the recommended method of the United Nations and appropriate policies were suggested for waste minimization. The collected results of this study show production of 185 tons of industrial solid wastes from 45 sources which contained 68.5% catalysts, 10.25% metal barrels, 18.61% aluminum ball, 2.62% plastic barrels and 0.02% paper. 93.3% of these wastes were generated as the result of catalysts change, 3.3% as the result of using chemicals and oils, 1.7% as the result of methanol solution amid application, and 1.1% because of aluminum ball changes. Based on the UNEP methods, the ammonia unit wastes classified as 19/7%hazadrous and 87,12% non hazardous. At present 87.12% of these wastes are being dumped in the area and 12.88% are sold. Proposed procedures for waste minimization contain 68.5% reuse and recycling and 31.5% recycling.

  18. Environmental impacts of waste management in the hospitality industry: Creating a waste management plan for Bergvik Kartano

    OpenAIRE

    Adigwe, Christopher

    2014-01-01

    Many hospitality industries find it difficult to control or manage solid wastes, such as food, containers, paper, cardboard and scrap metals, which are waste generated on a daily basis depending on the industry. Most hospitality industries tend to lag behind when it comes to the collection of waste. Only a fraction of the¬¬ waste collected receives proper disposal. When waste is not collected sufficiently and the disposal is inappropriate the waste can accumulate and cause water, land and air...

  19. Exploitation of Food Industry Waste for High-Value Products.

    Science.gov (United States)

    Ravindran, Rajeev; Jaiswal, Amit K

    2016-01-01

    A growing global population leads to an increasing demand for food production and the processing industry associated with it and consequently the generation of large amounts of food waste. This problem is intensified due to slow progress in the development of effective waste management strategies and measures for the proper treatment and disposal of waste. Food waste is a reservoir of complex carbohydrates, proteins, lipids, and nutraceuticals and can form the raw materials for commercially important metabolites. The current legislation on food waste treatment prioritises the prevention of waste generation and least emphasises disposal. Recent valorisation studies for food supply chain waste opens avenues to the production of biofuels, enzymes, bioactive compounds, biodegradable plastics, and nanoparticles among many other molecules. Copyright © 2015 Elsevier Ltd. All rights reserved.

  20. Determination of Heavy Metal Levels in Various Industrial Waste Waters

    Directory of Open Access Journals (Sweden)

    Mustafa Şahin Dündar

    2012-06-01

    Full Text Available Important part of the environmetal pollution consists of waste water and water pollution. The water polluted by anthropogenical, industrial, and agricultural originated sources are defined as waste waters which are the main pollution sources for reservoirs, rivers, lakes, and seas. In this work, waste waters of leather, textile, automotive side, and metal plating industries were used to determine the levels of Cu, Zn, Cr, Pb and Ni by using Flame Atomic Absorption Spectrometer. As a result, highest mean levels of copper in supernatants of plating and textile industries were observed as 377,18 ng ml-1, respectively 103 ng ml-1 lead and 963,6 ng ml-1 nickel in plating industry, 1068,2 ng ml-1 zinc and 14557,1 ng ml-1 chromium in plating and leather industries were determined.

  1. Manual on oil-gas industry waste utilization radioecological safety

    International Nuclear Information System (INIS)

    Kudryashev, V.A.; Lukashenko, S.N.; Tuleushev, A.Zh.; Marabaev, Zh.N.; Pasysaev, V.A.; Kayukov, P.G.; Kozhakhmetov, N.B.; Shevtsov, S.P.

    2003-01-01

    The development of a new document - 'Manual on radio-ecologically safe utilization of waste from oil-and-gas production' is carried out. This document regulates the whole cycle of environment protection measures at waste utilization for the named industry in Kazakhstan and is aimed on lowering the radiation risks and assurance of radioecological safety both at present and for the future. The document presents a set regulations necessary for radioactive wastes handling in the oil-gas industry. The normative document was agreed in both the Ministry of Health of the Republic of Kazakhstan (RK) and Ministry of Environment Protection of RK

  2. Waste to Wealth: Hidden Treasures in the Oil Palm Industry

    International Nuclear Information System (INIS)

    Loh Soh Kheang; Astimar Abdul Aziz; Ravigadevi Sambathamurthi; Mohd Basri Wahid

    2010-01-01

    The palm oil industry plays an important role in the creation of waste to wealth using the abundant oil palm biomass resources generated from palm oil supply chain i.e. upstream to downstream activities. The oil palm biomass and other palm-derived waste streams available are oil palm trunks (felled), fronds (felled and pruned), shell, mesocarp fibers, empty fruit bunches (EFB), palm oil mill effluent (POME), palm kernel expelled (PKE), palm fatty acid distillates (PFAD), used frying oil (UFO), residual oil from spent bleaching earth (SBE) and glycerol. For 88.5 million tonnes of fresh fruit bunches (FFB) processed in 2008, the amount of oil palm biomass generated was more than 25 million tones (dry weight basis) with the generation of 59 million tonnes of POME from 410 palm oil mills. Oil palm biomass consists of mainly lignocellulose materials that can be potentially and fully utilized for renewable energy, wood-based products and high value-added products such as pytonutrients, phenolics, carotenes and vitamin E. Oil palm biomass can be converted to bio energy with high combustible characteristics such as briquettes, bio-oils, bio-producer gas, boiler fuel, biogas and bio ethanol. Oil palm biomass can also be made into wood-based products such as composite and furniture, pulp and paper and planting medium. The recovery of phenolics from POME as valuable antioxidants has potential drug application. Other possible applications for oil palm biomass include fine chemicals, dietary fibers, animal feed and polymers. There must be a strategic and sustainable resource management to distribute palm oil and palm biomass to maximize the use of the resources so that it can generate revenues, bring benefits to the palm oil industry and meet stringent sustainability requirements in the future. (author)

  3. Using game theory to improve safety within chemical industrial parks

    CERN Document Server

    Reniers, Genserik

    2013-01-01

    Though the game-theoretic approach has been vastly studied and utilized in relation to economics of industrial organizations, it has hardly been used to tackle safety management in multi-plant chemical industrial settings. Using Game Theory for Improving Safety within Chemical Industrial Parks presents an in-depth discussion of game-theoretic modelling which may be applied to improve cross-company prevention and -safety management in a chemical industrial park.   By systematically analyzing game-theoretic models and approaches in relation to managing safety in chemical industrial parks, Using Game Theory for Improving Safety within Chemical Industrial Parks explores the ways game theory can predict the outcome of complex strategic investment decision making processes involving several adjacent chemical plants. A number of game-theoretic decision models are discussed to provide strategic tools for decision-making situations.   Offering clear and straightforward explanations of methodologies, Using Game Theor...

  4. Guidelines for generators of hazardous chemical waste at LBL and guidelines for generators of radioactive and mixed waste at LBL

    International Nuclear Information System (INIS)

    1993-10-01

    The purpose of this document is to provide the acceptance criteria for the transfer of hazardous chemical waste to LBL's Hazardous Waste Handling Facility (HWHF). Hazardous chemical waste is a necessary byproduct of LBL's research and technical support activities. This waste must be handled properly if LBL is to operate safely and provide adequate protection to staff and the environment. These guidelines describe how you, as a generator of hazardous chemical waste, can meet LBL's acceptance criteria for hazardous chemical waste

  5. Technological Proposals for Recycling Industrial Wastes for Environmental Applications

    Directory of Open Access Journals (Sweden)

    Isabel Romero-Hermida

    2014-08-01

    Full Text Available A two-fold objective is proposed for this research: removing hazardous and unpleasant wastes and mitigating the emissions of green house gasses in the atmosphere. Thus, the first aim of this work is to identify, characterize and recycle industrial wastes with high contents of calcium or sodium. This involves synthesizing materials with the ability for CO2 sequestration as preliminary work for designing industrial processes, which involve a reduction of CO2 emissions. In this regard, phosphogypsum from the fertilizer industry and liquid wastes from the green olive and bauxite industries have been considered as precursors. Following a very simple procedure, Ca-bearing phosphogypsum wastes are mixed with Na-bearing liquid wastes in order to obtain a harmless liquid phase and an active solid phase, which may act as a carbon sequestration agent. In this way, wastes, which are unable to fix CO2 by themselves, can be successfully turned into effective CO2 sinks. The CO2 sequestration efficiency and the CO2 fixation power of the procedure based on these wastes are assessed.

  6. Statistical study of chemical additives effects in the waste cementation

    International Nuclear Information System (INIS)

    Tello, Cledola C.O. de; Diniz, Paula S.; Haucz, Maria J.A.

    1997-01-01

    This paper presents the statistical study, that was carried out to analyse the chemical additives effect in the waste cementation process. Three different additives from two industries were tested: set accelerator, set retarder and super plasticizers, in cemented pates with and without bentonite. The experiments were planned in accordance with the 2 3 factorial design, so that the effect of each type of additive, its quantity and manufacturer in cemented paste and specimens could be evaluated. The results showed that the use of these can improve the cementation process and the product. The admixture quantity and the association with bentonite were the most important factors affecting the process and product characteristics. (author). 4 refs., 9 figs., 4 tabs

  7. Characterization of waste waters of tannery, fertilizer and textile industries in Multan region

    International Nuclear Information System (INIS)

    Ansan, T.M.; Malik, S.A.

    2001-01-01

    This study evaluates various physico-chemical characteristics such as pH, electrical conductivity, dissolved solids, hardness, apparent color, odor, elemental concentrations, chloride contents, carbonates, bicarbonates, residual sodium carbonate and sodium absorption ratio of waste waters of three major industries, i.e. tannery, fertilizer and textile, situated in Multan District of the Punjab province, Pakistan. Waste waters, in general, have been found to be hard, alkaline in nature and contain variable amounts of dissolved solids. High concentration of chromium (10.7 mg 1-1) was found in tannery wastewater. Zinc and copper concentrations were not quantifiable. Water quality classes (C4-S4), (C4-S1) and (C4-S1, C3-S1, C3-S4 and C3-S2) have been assigned to tannery, fertilizer and textile waste waters respectively. Results indicate that these untreated industrial waste waters are potential hazards to human health and unsuitable for irrigation usage. (author)

  8. Recycling industrial waste in brick manufacture. Part 1

    Directory of Open Access Journals (Sweden)

    Andreola, F.

    2005-12-01

    Full Text Available The ongoing accumulation of industrial waste speaks to the need to seek cost-effective disposal methods. Brick manufacture would appear to be particularly promising in this regard. The present study analyzes the possibility of recycling the sludge generated in porcelain tile polishing, as well as coal, steel and municipal incinerator ash to make a special type of facing brick whose properties readily accommodate a full analysis of all the problems deriving from the incorporation of residue in its manufacture. Physical-chemical, mechanical and structural analyses were performed on bricks made with varying percentages of the different types of waste considered. This first paper reports the results of the physical arid technological characterization of the products; the second part of the research will address their chemical, mechanical and structural properties.

    El continuo aumento de la cantidad de residuos (desechos que se generan en los procesos industriales induce a buscar nuevos métodos alternativos a la disposición final que sean altamente eficientes y a bajo costo. La industria manufac turera de ladrillos resulta muy prometedora desde este punto de vista. En este trabajo ha sido investigada la posibilidad de usar distintos residuos industriales, entre ellos barros de pulido del gres porcelánico. cenizas de carbón, cenizas de acerías y de incinerador municipal para la fabricación de ladrillos de exteriores. Fueron analizados los problemas que podrían derivar al introducir estos residuos en la pasta. En particular, en esta primera parte del trabajo se muestran los resultados derivados de la introducción de los residuos considerados, en distintos porcentajes, sobre las propiedades físicas y tecnológicas del producto final. En la segunda parte se desarrollarán los efectos causados sobre las propiedades químicas, mecánicas y microestructurales.

  9. Management of radioactive waste of scientific and industrial centers

    International Nuclear Information System (INIS)

    Sobolev, I.A.; Dmitriev, S.A.; Barinov, A.S.; Ojovan, M.I.; Timofeev, E.M.

    1995-01-01

    Available for the time being in the Russian Federation, a system of management of institutional and industrial radioactive waste (e.g. radioactive waste from industry, medicine, scientific organizations and other, which are not related to the nuclear fuel cycle or defense) provides for its collection, transportation, storage, treatment, immobilization and disposal by a network of special enterprises. Russia has 16 such enterprises. Moscow Scientific and Industrial Association Radon deals with the problems of radioactive waste from Central European part of Russia, which includes Moscow, Moscow Region and also Tverskaya, Yaroslavskaya, Vladimirskaya, Kostromskaya, Kaluzhskaya, Bryanskaya, Smolenskaya, Tulskaya, Ryazanskaya regions. The population of the central part of Russia constitutes about 40 million people. At the same time about 80% of the radioactive waste, which is collected for treatment and disposal from the territory of Russia, is included in this region. The average volume of the waste to be treated at SIA Radon is 3,000 m 3 per year for solid waste and 350 m 3 per year for liquid waste. Total radioactivity of processed waste is up to 4 PBq per year

  10. Product waste in the automotive industry : Technology and environmental management

    NARCIS (Netherlands)

    Groenewegen, Peter; Hond, Frank Den

    1993-01-01

    In this article the changes in technology and industry structure forced by waste management in the automotive industry are explored. The analysis is based on (1) a characterisation of corporate response to environmental issues, and (2) the management of technology applied to the car manufacturing

  11. Biological treatment of industrial wastes; Tratamiento biologico de residuos industriales

    Energy Technology Data Exchange (ETDEWEB)

    Ortiz de Zarate Apodaca, J.M.; Abia Aguila, L

    1997-04-01

    There are organic elements used in industrial processes which are not able to be recovered. The biological treatment is the alternative for eliminating the organic pollutants from industrial waste water. This technology is being widely accepted because of its low environmental impact. (Author)

  12. Analyzing solid waste management practices for the hotel industry

    Directory of Open Access Journals (Sweden)

    S.T. Pham Phu

    2018-01-01

    Full Text Available The current study aims to analyze waste characteristics and management practices of the hotel industry in Hoi An, a tourism city in the center of Vietnam. Solid wastes from 120 hotels were sampled, the face-to-face interviews were conducted, and statistical methods were carried out to analyze the data. The results showed that the mean of waste generation rate of the hotels was 2.28 kg/guest/day and strongly correlated to internal influencing factors such as the capacity, the price of the room, garden, and level of restaurant. The differences in waste generation rate of the hotels were proved to be statistically significant. The higher the scale of hotels, the higher the waste generation rate. Moreover, the waste composition of the hotels was identified by 58.5% for biodegradable waste, 25.8% for recyclables and 15.7% for others. The relative differences in the waste composition of the hotels by climate, the features of hotels, and the types of the guest were explained. Whereby, the higher size of the hotels, the higher percentage of biodegradable and less proportion of recyclable waste. Also, this study revealed that the implementation status of waste management practices of the hoteliers initially reaped quite positive achievements with 76% for sorting, 39% for recycling, 29% for reduction, and 0.8% for composting. The rate of waste management practices was proportional to the scale of the hotel. This study provided information on waste management practice of hotel industry and contributed to the overall assessment of municipal solid waste management practices of Hoi An city.

  13. An industrial ecology approach to municipal solid waste ...

    Science.gov (United States)

    Municipal solid waste (MSW) can be viewed as a feedstock for industrial ecology inspired conversions of wastes to valuable products and energy. The industrial ecology principle of symbiotic processes using waste streams for creating value-added products is applied to MSW, with examples suggested for various residual streams. A methodology is presented to consider individual waste-to-energy or waste-to-product system synergies, evaluating the economic and environmental issues associated with each system. Steps included in the methodology include identifying waste streams, specific waste components of interest, and conversion technologies, plus steps for determining the economic and environmental effects of using wastes and changes due to transport, administrative handling, and processing. In addition to presenting the methodology, technologies for various MSW input streams are categorized as commercialized or demonstrated to provide organizations that are considering processes for MSW with summarized information. The organization can also follow the methodology to analyze interesting processes. Presents information useful for analyzing the sustainability of alternatives for the management of municipal solid waste.

  14. Nasreya: a treatment and disposal facility for industrial hazardous waste in Alexandria, Egypt: phase I.

    Science.gov (United States)

    Ramadan, Adham R; Kock, Per; Nadim, Amani

    2005-04-01

    A facility for the treatment and disposal of industrial hazardous waste has been established in Alexandria, Egypt. Phase I of the facility encompassing a secure landfill and solar evaporation ponds is ready to receive waste, and Phase II encompassing physico-chemical treatment, solidification, and interim storage is underway. The facility, the Nasreya Centre, is the first of its kind in Egypt, and represents the nucleus for the integration, improvement and further expansion of different hazardous waste management practices and services in Alexandria. It has been developed within the overall legal framework of the Egyptian Law for the Environment, and is expected to improve prospects for enforcement of the regulatory requirements specified in this law. It has been developed with the overall aim of promoting the establishment of an integrated industrial hazardous waste management system in Alexandria, serving as a demonstration to be replicated elsewhere in Egypt. For Phase I, the Centre only accepts inorganic industrial wastes. In this respect, a waste acceptance policy has been developed, which is expected to be reviewed during Phase II, with an expansion of the waste types accepted.

  15. The chemical industry of uranium in France

    International Nuclear Information System (INIS)

    Goldschmidt, B.

    1955-01-01

    The actual CEA program is concerned with the construction of two large graphite reactors, each of those containing at least one hundred tons of uranium metal with nuclear purity. The uranium for these two reactors will be regularly supplied by new resources discovered in France and Madagascar in the last five years. The working and treatment of such ore have led to the creation of an important french industry of which the general outline and principle are described. The operated ores have got different natures and concentration, individual characteristics are described for the main ores.The most high-grade ore are transported to a central plant in Bouchet near Paris; the low-grade ore are concentrated by physical methods or chemical processes of which principles and economy are studied with constancy. The acid processes are the only used until now, although the carbonated alkaline processes has been studied in France. The next following steps after the acid process until the obtention of uranium rich concentrate are described. The purification steps of uranium compounds to nuclear purity material are described as well as the steps to elaborate metal of which the purity grade will be specify. Finally, the economic aspects of uranium production difficulty will be considered in relation with technical progresses which we can expect to achieve in the future. (M.P.)

  16. Interventions to Encourage and Facilitate Greener Industrial Chemicals Selection

    OpenAIRE

    Faulkner, David

    2017-01-01

    Despite their ubiquity in modern life, industrial chemicals are poorly regulated in the United States. Statutory law defines industrial chemicals as chemicals that are not foods, drugs, cosmetics, nor pesticides, but may be used in consumer products, and this distinction places them under the purview of the Toxic Substances Control Act (TSCA), which received a substantial update when the US congress passed a revision of the act in 2016. The revised law, the Frank R. Lautenberg Chemical Safety...

  17. Release of Waste Tire Comprehensive Utilization Industry Access Conditions

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    On July 31, 2012, the Ministry of Industry and Information Technology released the Tire Retread- ing lndustry Access Conditions and Waste Tire Comprehensive Utilization Industry Access Condi- tions with the No. 32 announcement of 2012. The state will lay a foundation for realizing the green, safe, efficient, eco-friendly and energy saving tar- gets in the "12th Five-year Plan" of the industry by raising access conditions, regulating industrial development order, strengthening environmental protection, promoting corporate optimizing and up- grading, improving resources comprehensive utiliza- tion technology and management level and guiding the "harmless recycling and eco-friendly utiliza- tion" of the industry.

  18. Vitrification of lead-rich solid ashes from incineration of hazardous industrial wastes

    International Nuclear Information System (INIS)

    Kavouras, P.; Kaimakamis, G.; Ioannidis, Th. A.; Kehagias, Th.; Komninou, Ph.; Kokkou, S.; Pavlidou, E.; Antonopoulos, I.; Sofoniou, M.; Zouboulis, A.; Hadjiantoniou, C.P.; Nouet, G.; Prakouras, A.; Karakostas, Th.

    2003-01-01

    Lead-rich solid industrial wastes were vitrified by the addition of glass formers in various concentrations, to produce non-toxic vitreous stabilized products that can be freely disposed or used as construction materials. Toxicity of both the as-received industrial solid waste and the stabilized products was determined using standard leaching test procedures. The chemically stable vitreous products were subjected to thermal annealing in order to investigate the extent of crystal separation that could occur during cooling of large pieces of glass. Leaching tests were repeated to investigate the relation between annealing process and chemical stability. X-ray, scanning and transmission electron microscopy techniques were employed to identify the microstructure of stabilized products before and after thermal treatment. Relation between synthesis and processing, chemical stability and microstructure was investigated

  19. Chemical precipitation processes for the treatment of aqueous radioactive waste

    International Nuclear Information System (INIS)

    1992-01-01

    Chemical precipitation by coagulation-flocculation and sedimentation has been commonly used for many years to treat liquid (aqueous) radioactive waste. This method allows the volume of waste to be substantially reduced for further treatment or conditioning and the bulk of the waste to de discharged. Chemical precipitation is usually applied in combination with other methods as part of a comprehensive waste management scheme. As with any other technology, chemical precipitation is constantly being improved to reduce cost to increase the effectiveness and safety on the entire waste management system. The purpose of this report is to review and update the information provided in Technical Reports Series No. 89, Chemical Treatment of Radioactive Wastes, published in 1968. In this report the chemical methods currently in use for the treatment of low and intermediate level aqueous radioactive wastes are described and illustrated. Comparisons are given of the advantages and limitations of the processes, and it is noted that good decontamination and volume reduction are not the only criteria according to which a particular process should be selected. Emphasis has been placed on the need to carefully characterize each waste stream, to examine fully the effect of segregation and the importance of looking at the entire operation and not just the treatment process when planning a liquid waste treatment facility. This general approach includes local requirements and possibilities, discharge authorization, management of the concentrates, ICRP recommendations and economics. It appears that chemical precipitation process and solid-liquid separation techniques will continue to be widely used in liquid radioactive waste treatment. Current research and development is showing that combining different processes in one treatment plant can provide higher decontamination factors and smaller secondary waste arisings. Some of these processes are already being incorporated into new and

  20. Fermentation of household wastes and industrial waste water; Vergaerung von haeuslichen Abfaellen und Industrieabwaessern

    Energy Technology Data Exchange (ETDEWEB)

    Edelmann, W [Arbeitsgemeinschaft Bioenergie ' arbi' , Maschwanden (Switzerland); Engeli, H [Probag AG, Dietikon (Switzerland); Glauser, M [Biol-Conseils SA, Neuchatel (Switzerland); Hofer, H [HTH-Verfahrenstechnik, Winterthur (Switzerland); Membrez, Y [EREP SA, Aclens (Switzerland); Meylan, J -H [Lausanne (Switzerland); Schwitzguebel, J -P [Swiss Federal Institute of Technology (EPFL), Genie biologique, Lausanne (Switzerland)

    1993-07-01

    This comprehensive brochure reviews various technologies for the environment-friendly treatment of organic wastes and residues. The principles of anaerobic digestion are discussed. Authorities, planners and engineers concerned with waste treatment are provided with an overview of current technology in the organic wastes area. The brochure emphasises the importance of fermentation processes in waste treatment, discusses the legal pre-requisites for biogas production, lists the biological and process-oriented fundamentals of fermentation and examines the energy potential of biogenic wastes and waste water. Further, details are given on the treatment of both industrial waste water and solid organic wastes and, finally, the economics of fermentation is examined. Useful data is presented in table form and the various processes described are illustrated by schematics and flow diagrams. An appendix lists suggestions for further reading on the subject.

  1. Opportunity Analysis for Recovering Energy from Industrial Waste Heat and Emissions

    Energy Technology Data Exchange (ETDEWEB)

    Viswanathan, Vish V.; Davies, Richard W.; Holbery, Jim D.

    2006-04-01

    United States industry consumed 32.5 Quads (34,300 PJ) of energy during 2003, which was 33.1% of total U.S. energy consumption (EIA 2003 Annual Energy Review). The U.S. industrial complex yields valuable goods and products. Through its manufacturing processes as well as its abundant energy consumption, it supports a multi-trillion dollar contribution to the gross domestic product and provides millions of jobs in the U.S. each year. Industry also yields waste products directly through its manufacturing processes and indirectly through its energy consumption. These waste products come in two forms, chemical and thermal. Both forms of waste have residual energy values that are not routinely recovered. Recovering and reusing these waste products may represent a significant opportunity to improve the energy efficiency of the U.S. industrial complex. This report was prepared for the U.S. Department of Energy Industrial Technologies Program (DOE-ITP). It analyzes the opportunity to recover chemical emissions and thermal emissions from U.S. industry. It also analyzes the barriers and pathways to more effectively capitalize on these opportunities. A primary part of this analysis was to characterize the quantity and energy value of the emissions. For example, in 2001, the industrial sector emitted 19% of the U.S. greenhouse gases (GHG) through its industrial processes and emitted 11% of GHG through electricity purchased from off-site utilities. Therefore, industry (not including agriculture) was directly and indirectly responsible for emitting 30% of the U.S. GHG. These emissions were mainly comprised of carbon dioxide (CO2), but also contained a wide-variety of CH4 (methane), CO (carbon monoxide), H2 (hydrogen), NMVOC (non-methane volatile organic compound), and other chemicals. As part of this study, we conducted a survey of publicly available literature to determine the amount of energy embedded in the emissions and to identify technology opportunities to capture and

  2. Food waste generation and industrial uses: A review.

    Science.gov (United States)

    Girotto, Francesca; Alibardi, Luca; Cossu, Raffaello

    2015-11-01

    Food waste is made up of materials intended for human consumption that are subsequently discharged, lost, degraded or contaminated. The problem of food waste is currently on an increase, involving all sectors of waste management from collection to disposal; the identifying of sustainable solutions extends to all contributors to the food supply chains, agricultural and industrial sectors, as well as retailers and final consumers. A series of solutions may be implemented in the appropriate management of food waste, and prioritised in a similar way to waste management hierarchy. The most sought-after solutions are represented by avoidance and donation of edible fractions to social services. Food waste is also employed in industrial processes for the production of biofuels or biopolymers. Further steps foresee the recovery of nutrients and fixation of carbon by composting. Final and less desirable options are incineration and landfilling. A considerable amount of research has been carried out on food waste with a view to the recovery of energy or related products. The present review aims to provide an overview of current debate on food waste definitions, generation and reduction strategies, and conversion technologies emerging from the biorefinery concept. Copyright © 2015 Elsevier Ltd. All rights reserved.

  3. Chemicals-Industry of the Future; Industrial Partnerships: Advancing Energy and Environmental Goals

    International Nuclear Information System (INIS)

    DOE Office of Industrial Technologies

    2001-01-01

    This tri-fold brochure describe the partnering activities of the Office of Industrial Technologies' (OIT) Industries of the Future (IOF) for Chemicals. Information on what works for the Chemicals industry, examples of successful partnerships, and benefits of partnering with OIT are included

  4. The use of the Kelor Seeds (Moringa oleifera) as alternative coagulant in waste delivery process of textile industrial waste

    Science.gov (United States)

    Rambe, AM; Pandia, S.; Ginting, MHS; Tambun, R.; Haryanto, B.

    2018-02-01

    This research is to know the influence of moringa seed as coagulant, pH of liquid waste textile industry (jeans wash), size of moringa seed particles to decrease of turbidity percentage. Measurements were made to Total Suspended Solid, Color Rate and Chemical Oxygen Demand for wastewater textile industry by coagulation - flocculation method. Variables of this study were conducted on dosage of moringa, with particle size 212 mesh. The results showed that moringa seeds as coagulant dose optimum is 1250 mg/L for the textile industry wastewater at pH 7.8. Moringa seed powder is about 212 mesh with a dose of 1250 mg/L can lower the turbidity of 77.77%, Total Suspended Solid amounted to 83.69% and Chemical Oxygen Demand amounted to 75.86%.

  5. Industrial Wastes as Auxiliary Additives to Cement/Lime Stabilization of Soils

    Directory of Open Access Journals (Sweden)

    Jijo James

    2016-01-01

    Full Text Available Chemical stabilization involves the use of chemical agents for initiating reactions within the soil for modification of its geotechnical properties. Cement and lime stabilization have been the most common stabilization methods adopted for soil treatment. Cement stabilization results in good compressive strengths and is preferred for cohesionless to moderately cohesive soil but loses effectiveness when the soil is highly plastic. Lime stabilization is the most preferred method for plastic clays; however, it proves to be ineffective in sulphate rich clays and performs poorly under extreme conditions. With such drawbacks, lots of researches have been undertaken to address the issues faced with each stabilization method, in particular, the use of solid wastes for soil stabilization. Solid waste reuse has gained high momentum for achieving sustainable waste management in recent times. Research has shown that the use of solid wastes as additives with and replacement for conventional stabilizers has resulted in better results than the performance of either individually. This review provides insight into some of the works done by earlier researchers on lime/cement stabilization with industrial wastes as additives and helps to form a sound platform for further research on industrial wastes as additives to conventional stabilizers.

  6. Industrial aspects of radioactive waste management in Western Europe

    International Nuclear Information System (INIS)

    Marcus, F.R.; Seynaeve, F.

    1977-01-01

    In 1980 there will be about 120 nuclear power reactors with 70,000 MWe in operation in Western Europe, and this number will be doubled by 1985, when the nuclear capacity in operation is expected to be 180,000 MWe. Predictions are made of the waste management requirements resulting from this nuclear expansion. Until a few years ago waste from nuclear research and from the use of isotopes in medicine has been the dominating source. Now there is a much larger proportion from the day to day operation of nuclear power reactors. Waste amounts from reprocessing of spent reactor fuel will rise more slowly. Waste production in other fuel cycle industries is relatively insignificant. There will be around 30 reactors and other nuclear plants to take out of operation in Western Europe around 1990. The large-scale handling of these wastes calls for overall management schemes, based on clear policies for storage and disposal. Questions are identified which have to be answered within the next few years in order to allow the orderly development of such large-scale waste management. These questions deal with: (i) rules and regulations, (ii) new technical evidence, (iii) administrative frameworks and responsibilities. Several areas of waste management are well suited to commercial waste operating firms, already established at present in a number of European countries. The scope for waste operators may include waste transportation, operating of own or government owned treatment and storage installations, and the carrying out of disposal operations. In the paper, development needs originally suggested by the Foratom waste study group will be discussed in the light of a late 1976 review to be carried through by European industry

  7. Industrial aspects of radioactive waste management in Western Europe

    International Nuclear Information System (INIS)

    Marcus, F.R.; Seynaeve, F.

    1977-01-01

    In 1980 about 120 nuclear power reactors with 70,000MW(e) will be in operation in Western Europe, and this number will be doubled by the second half of the 1980s, when the nuclear capacity in operation is expected to be 180,000MW(e). Predictions are made of the waste management requirements resulting from this nuclear expansion. Until a few years ago nuclear research and the use of isotopes in medicine have been the dominating source of radioactive waste. Now there is a much larger proportion from the day-to-day operation of nuclear power reactors. The amount of waste from reprocessing spent reactor fuel will rise more slowly. Waste production in other fuel cycle industries is relatively insignificant. Approximately 30 reactors and other nuclear plants will be taken out of operation in Western Europe by about 1990. The large-scale handling of these wastes calls for overall management schemes based on clear policies for storage and disposal. Questions are identified which will have to be answered within the next few years in order to allow the orderly development of such large-scale waste management. These questions deal with (i) rules and regulations, (ii) new technical evidence, (iii) administrative framework and responsibilities. Several areas of waste management are well suited to commercial waste operating firms already established in a number of European countries. The scope for waste operators may include transport of waste, operation of own or government-owned treatment and storage installations, and disposal operations. Development requirements originally suggested by the Foratom waste study group are discussed in the light of the latest developments as seen by European industry. (author)

  8. Bioprocessing of concentrated mixed hazardous industrial waste

    International Nuclear Information System (INIS)

    Wolfram, J.H.; Rogers, R.D.; Silver, G.; Attalla, A.; Prisc, M.

    1994-01-01

    The use of selected microorganisms for the degradation and/or the detoxification of hazardous organic compounds is gaining wide acceptance as an alternative waste treatment technology. This work describes the unique capabilities of an isolated strain of Pseudomonas for metabolizing methylated aromatic compounds. This strain of Pseudomonas putida Idaho is unique in that it can tolerate and grow under a layer of neat p-xylene. A bioprocess has been developed to degrade LLW and mixed wastes containing methylated aromatic compounds, i.e., pseudocumene, toluene and p-xylene. The process is now in the demonstration phase at a DOE facility and has been running for one year. Feed concentrations of 21200 ppm of the toxic organic substrate have been fed to the bioreactor. This report describes the results obtained thus far

  9. Radioactive waste: the poisoned legacy of the nuclear industry

    International Nuclear Information System (INIS)

    Rousselet, Y.

    2011-01-01

    The nuclear industry produces a huge amount of radioactive waste from one end to the other of the nuclear cycle: i.e. from mining uranium to uranium enrichment through reactor operating, waste reprocessing and dismantling nuclear power plants. Nuclear power is now being 'sold' to political leaders and citizens as an effective way to deal with climate change and ensure security of energy supplies. Nonetheless, nuclear energy is not a viable solution and is thus a major obstacle to the development of clean energy for the future. In addition to safety and security issues, the nuclear industry is, above all, faced with the huge problem of how to deal with the waste it produces and for which it has no solution. This ought to put a brake on the nuclear industry, but instead, against all expectations, its development continues to gather pace. (author)

  10. Industrial hazardous waste management in Turkey: Current state of the field and primary challenges

    International Nuclear Information System (INIS)

    Salihoglu, Gueray

    2010-01-01

    A holistic evaluation of a country's hazardous waste management (HWM) practices is useful in identifying the necessary actions to focus on. Based on an analysis of industrial hazardous waste (HW) generation in Turkey, this paper attempts to critically evaluate and report current Turkish HWM practices and discuss the primary challenges to be addressed. The generation of industrial HW for Turkey reported in 2004 was 1.195 million tons, which accounted for 7% of the total industrial solid waste (ISW) generated by the manufacturing industry, and for nearly 4.9% of the total solid waste generated in the country. The HW generated by the top five manufacturing product categories - basic metals, chemicals and chemical products, food and beverages, coke and refined petroleum, motor vehicles and trailers - accounted for 89.0% of total industrial HW. 21% of the HW generated in 2004 was recycled or reused, and 6% was sold or donated, whereas 73% was sent to ultimate disposal. 67% of the HW sent to ultimate disposal was disposed of at municipal landfills. The total capacity of the existing regional HW facilities is 212,500 tons/year, which accounts for about 24% of the HW to be disposed. Turkey has identified the HW problem in the country and enacted legislation, designated a lead agency, and promulgated rules and regulations. Several new initiatives are planned for improving HW management nationally; however, some HWM problems will be persistent due to previous and existing industrial development plans. These development policies led to the concentration of industry in regions marked by precious agricultural fields and high population density. This occurred because the government previously exhibited a default prioritization towards industrial development, leading to insufficient implementation of regulations on HW generators. Some of the problems may also be rooted in other countries that allow illegal transboundary HW movements despite international regulations.

  11. Methods of industrial waste water cleaning

    Directory of Open Access Journals (Sweden)

    Ján Brehuv

    2005-11-01

    Full Text Available The issue of „acid mine water“ (or AMD is well known in the world for some centuries. In the Eastern Slovakia, the most acid surface water occurs in the area of the old mine Smolník, which is closed and submerged for 15 years. The submitted contribution deals with the sulphateelimination at this locality. Recently, several methods of the sulphate-elimination from the mine water are applied. The best-known methods are the biological and physical-chemical oness and the chemical precipitation. The method described in this contribution deals with the chemical precipitation by polyaluminium chloride and calcium hydrate. By appliying of this method, very interesting results were obtained. The amount of SO42- anions decreased to almost zero-value, using optimal doses of the chemical reagents.

  12. Biobased chemicals: the convergence of green chemistry with industrial biotechnology.

    Science.gov (United States)

    Philp, Jim C; Ritchie, Rachael J; Allan, Jacqueline E M

    2013-04-01

    Policy issues around biobased chemicals are similar to those for biobased plastics. However, there are significant differences that arise from differences in production volumes and the more specific applications of most chemicals. The drivers for biobased chemicals production are similar to those for biobased plastics, particularly the environmental drivers. However, in Europe, biobased chemical production is further driven by the need to improve the competitiveness of the chemicals industry. Copyright © 2013 Elsevier Ltd. All rights reserved.

  13. Chemical digestion of low level nuclear solid waste material

    International Nuclear Information System (INIS)

    Cooley, C.R.; Lerch, R.E.

    1976-01-01

    A chemical digestion for treatment of low level combustible nuclear solid waste material is provided and comprises reacting the solid waste material with concentrated sulfuric acid at a temperature within the range of 230 0 --300 0 C and simultaneously and/or thereafter contacting the reacting mixture with concentrated nitric acid or nitrogen dioxide. In a special embodiment spent ion exchange resins are converted by this chemical digestion to noncombustible gases and a low volume noncombustible residue. 6 claims, no drawings

  14. Solid waste management in the hospitality industry: a review.

    Science.gov (United States)

    Pirani, Sanaa I; Arafat, Hassan A

    2014-12-15

    Solid waste management is a key aspect of the environmental management of establishments belonging to the hospitality sector. In this study, we reviewed literature in this area, examining the current status of waste management for the hospitality sector, in general, with a focus on food waste management in particular. We specifically examined the for-profit subdivision of the hospitality sector, comprising primarily of hotels and restaurants. An account is given of the causes of the different types of waste encountered in this sector and what strategies may be used to reduce them. These strategies are further highlighted in terms of initiatives and practices which are already being implemented around the world to facilitate sustainable waste management. We also recommended a general waste management procedure to be followed by properties of the hospitality sector and described how waste mapping, an innovative yet simple strategy, can significantly reduce the waste generation of a hotel. Generally, we found that not many scholarly publications are available in this area of research. More studies need to be carried out on the implementation of sustainable waste management for the hospitality industry in different parts of the world and the challenges and opportunities involved. Copyright © 2014 Elsevier Ltd. All rights reserved.

  15. Classification of radioactive wastes produced by the nuclear industry

    International Nuclear Information System (INIS)

    2013-01-01

    This document first indicates the origins of radioactive wastes (mainly electronuclear industry), and the composition of spent fuel, and that only fission products and minor actinides are considered as radioactive wastes whereas uranium and plutonium can be used as new fuel after recycling. The classification of radioactive wastes is indicated in terms of radioactivity level and radionuclide half-life: high level (0.2 per cent of the total waste volume but 96 per cent of total waste radioactivity), medium level long life (3 per cent of volume, 4 per cent of radioactivity), low level long life (7 per cent of volume, 0.1 per cent of radioactivity), low and medium level and short life (63 per cent of volume and 0.02 per cent of radioactivity), very low level (27 per cent of volume and less than 0.01 per cent of radioactivity). An overview of radioactive waste processing and storage in France is presented for each category. Current and predicted volumes are indicated for each category. The main challenges are briefly addressed: spent fuel recycling, waste valorisation by fourth-generation reactors. Processing locations in France and in the World are indicated. Some key figures are provided: 2 kg of radioactive waste are produced per inhabitant and per year, and waste management costs represent 5 per cent of the total cost of produced electricity

  16. Chemical characterization of SRP waste tank sludges and supernates

    International Nuclear Information System (INIS)

    Gray, L.W.; Donnan, M.Y.; Okamoto, B.Y.

    1979-08-01

    Most high-level liquid wastes at the Savannah River Plant (SRP) are byproducts from plutonium and enriched uranium recovery processes. The high-level liquid wastes generated by these separations processes are stored in large, underground, carbon-steel tanks. The liquid wastes consist of: supernate (an aqueous solution containing sodium, nitrate, nitrite, hydroxyl, and aluminate ions), sludge (a gelatinous material containing insoluble components of the waste, such as ferric and aluminum hydroxides, and mercuric and manganese oxides), and salt cake (crystals, such as sodium nitrate, formed by evaporation of water from supernate). Analyses of SRP wastes by laser-Raman spectrometry, atomic absorption spectrometry, spark-source mass spectrometry, neutron activation analysis, colorimetry, ion chromatography, and various other wet-chemical and radiochemical methods are discussed. These analyses are useful in studies of waste tank corrosion and of forms for long-term waste storage

  17. Direction of CRT waste glass processing: electronics recycling industry communication.

    Science.gov (United States)

    Mueller, Julia R; Boehm, Michael W; Drummond, Charles

    2012-08-01

    Cathode Ray Tube, CRT, waste glass recycling has plagued glass manufacturers, electronics recyclers and electronics waste policy makers for decades because the total supply of waste glass exceeds demand, and the formulations of CRT glass are ill suited for most reuse options. The solutions are to separate the undesirable components (e.g. lead oxide) in the waste and create demand for new products. Achieving this is no simple feat, however, as there are many obstacles: limited knowledge of waste glass composition; limited automation in the recycling process; transportation of recycled material; and a weak and underdeveloped market. Thus one of the main goals of this paper is to advise electronic glass recyclers on how to best manage a diverse supply of glass waste and successfully market to end users. Further, this paper offers future directions for academic and industry research. To develop the recommendations offered here, a combination of approaches were used: (1) a thorough study of historic trends in CRT glass chemistry; (2) bulk glass collection and analysis of cullet from a large-scale glass recycler; (3) conversations with industry members and a review of potential applications; and (4) evaluation of the economic viability of specific uses for recycled CRT glass. If academia and industry can solve these problems (for example by creating a database of composition organized by manufacturer and glass source) then the reuse of CRT glass can be increased. Copyright © 2012 Elsevier Ltd. All rights reserved.

  18. Comprehensive Planning for Classification and Disposal of Solid Waste at the Industrial Parks regarding Health and Environmental Impacts

    OpenAIRE

    Hashemi, Hassan; Pourzamani, Hamidreza; Rahmani Samani, Bahareh

    2014-01-01

    The aim of this study is the comprehensive planning for integrated management of solid waste at the industrial parks. The share of each industrial group including food, metal, chemical, non-metallic minerals, textile, electrical and electronical, and cellulose industries were 48.2, 14.9, 6.7, 22, 0.9, 0.6, and 6.5 percent, respectively. The results showed that nearly half of total industrial waste produced from the range of biological materials are biodegradable and discharging them without o...

  19. Chemical species of plutonium in Hanford radioactive tank waste

    International Nuclear Information System (INIS)

    Barney, G.S.

    1997-01-01

    Large quantities of radioactive wastes have been generated at the Hanford Site over its operating life. The wastes with the highest activities are stored underground in 177 large (mostly one million gallon volume) concrete tanks with steel liners. The wastes contain processing chemicals, cladding chemicals, fission products, and actinides that were neutralized to a basic pH before addition to the tanks to prevent corrosion of the steel liners. Because the mission of the Hanford Site was to provide plutonium for defense purposes, the amount of plutonium lost to the wastes was relatively small. The best estimate of the amount of plutonium lost to all the waste tanks is about 500 kg. Given uncertainties in the measurements, some estimates are as high as 1,000 kg (Roetman et al. 1994). The wastes generally consist of (1) a sludge layer generated by precipitation of dissolved metals from aqueous wastes solutions during neutralization with sodium hydroxide, (2) a salt cake layer formed by crystallization of salts after evaporation of the supernate solution, and (3) an aqueous supernate solution that exists as a separate layer or as liquid contained in cavities between sludge or salt cake particles. The identity of chemical species of plutonium in these wastes will allow a better understanding of the behavior of the plutonium during storage in tanks, retrieval of the wastes, and processing of the wastes. Plutonium chemistry in the wastes is important to criticality and environmental concerns, and in processing the wastes for final disposal. Plutonium has been found to exist mainly in the sludge layers of the tanks along with other precipitated metal hydrous oxides. This is expected due to its low solubility in basic aqueous solutions. Tank supernate solutions do not contain high concentrations of plutonium even though some tanks contain high concentrations of complexing agents. The solutions also contain significant concentrations of hydroxide which competes with other

  20. EQ6 Calculations for Chemical Degradation of Navy Waste Packages

    International Nuclear Information System (INIS)

    S. LeStrange

    1999-01-01

    The Monitored Geologic Repository Waste Package Operations of the Civilian Radioactive Waste Management System Management and Operating Contractor (CRWMS M and O) performed calculations to provide input for disposal of spent nuclear fuel (SNF) from the Navy (Refs. 1 and 2). The Navy SNF has been considered for disposal at the potential Yucca Mountain site. For some waste packages, the containment may breach (Ref. 3), allowing the influx of water. Water in the waste package may moderate neutrons, increasing the likelihood of a criticality event within the waste package. The water may gradually leach the fissile components and neutron absorbers out of the waste package. In addition, the accumulation of silica (SiO 2 ) in the waste package over time may further affect the neutronics of the system. This study presents calculations of the long-term geochemical behavior of waste packages containing the Enhanced Design Alternative (EDA) II inner shell, Navy canister, and basket components. The calculations do not include the Navy SNF in the waste package. The specific study objectives were to determine the chemical composition of the water and the quantity of silicon (Si) and other solid corrosion products in the waste package during the first million years after the waste package is breached. The results of this calculation will be used to ensure that the type and amount of criticality control material used in the waste package design will prevent criticality

  1. EQ6 Calculations for Chemical Degradation of Navy Waste Packages

    Energy Technology Data Exchange (ETDEWEB)

    S. LeStrange

    1999-11-15

    The Monitored Geologic Repository Waste Package Operations of the Civilian Radioactive Waste Management System Management & Operating Contractor (CRWMS M&O) performed calculations to provide input for disposal of spent nuclear fuel (SNF) from the Navy (Refs. 1 and 2). The Navy SNF has been considered for disposal at the potential Yucca Mountain site. For some waste packages, the containment may breach (Ref. 3), allowing the influx of water. Water in the waste package may moderate neutrons, increasing the likelihood of a criticality event within the waste package. The water may gradually leach the fissile components and neutron absorbers out of the waste package. In addition, the accumulation of silica (SiO{sub 2}) in the waste package over time may further affect the neutronics of the system. This study presents calculations of the long-term geochemical behavior of waste packages containing the Enhanced Design Alternative (EDA) II inner shell, Navy canister, and basket components. The calculations do not include the Navy SNF in the waste package. The specific study objectives were to determine the chemical composition of the water and the quantity of silicon (Si) and other solid corrosion products in the waste package during the first million years after the waste package is breached. The results of this calculation will be used to ensure that the type and amount of criticality control material used in the waste package design will prevent criticality.

  2. Industrial-Scale Processes For Stabilizing Radioactively Contaminated Mercury Wastes

    International Nuclear Information System (INIS)

    Broderick, T. E.; Grondin, R.

    2003-01-01

    This paper describes two industrial-scaled processes now being used to treat two problematic mercury waste categories: elemental mercury contaminated with radionuclides and radioactive solid wastes containing greater than 260-ppm mercury. The stabilization processes were developed by ADA Technologies, Inc., an environmental control and process development company in Littleton, Colorado. Perma-Fix Environmental Services has licensed the liquid elemental mercury stabilization process to treat radioactive mercury from Los Alamos National Laboratory and other DOE sites. ADA and Perma-Fix also cooperated to apply the >260-ppm mercury treatment technology to a storm sewer sediment waste collected from the Y-12 complex in Oak Ridge, TN

  3. Biogas from organically high polluted industrial waste waters

    Energy Technology Data Exchange (ETDEWEB)

    Sixt, H

    1985-06-01

    Organically high polluted waste water sets special claims for an economical purification and the process treatment. Up to now these waste waters are being purified by anaerobic processes with simultaneous biogas generation. The fourstep anaerobic degradation is influenced by a lot of important parameters. Extensive researchers in the field of anaerobic microbiology has improved the knowledge of the fundamental principles. Parallel the reactor technology is developed worldwide. In general it seems that the fixed-film-reactor with immobilized bacteria has the best future to purify organically high polluted industrial waste water with short retention times under stable operation conditions.

  4. Analyzing solid waste management practices for the hotel industry

    OpenAIRE

    S.T. Pham Phu; M.G. Hoang; T. Fujiwara

    2018-01-01

    The current study aims to analyze waste characteristics and management practices of the hotel industry in Hoi An, a tourism city in the center of Vietnam. Solid wastes from 120 hotels were sampled, the face-to-face interviews were conducted, and statistical methods were carried out to analyze the data. The results showed that the mean of waste generation rate of the hotels was 2.28 kg/guest/day and strongly correlated to internal influencing factors such as the capacity, the price of the room...

  5. Chemical treatment of mixed waste at the FEMP

    International Nuclear Information System (INIS)

    Honigford, L.; Sattler, J.; Dilday, D.; Cook, D.

    1996-01-01

    The Chemical Treatment Project is one in a series of projects implemented by the Fernald Environmental Management Project (FEMP) to treat mixed waste. The projects were initiated to address concerns regarding treatment capacity for mixed waste and to comply with requirements established by the Federal Facility Compliance Act. The Chemical Treatment Project is designed to utilize commercially available mobile technologies to perform treatment at the FEMP site. The waste in the Project consists of a variety of waste types with a wide range of hazards and physical characteristics. The treatment processes to be established for the waste types will be developed by a systematic approach including waste streams evaluation, projectization of the waste streams, and categorization of the stream. This information is utilized to determine the proper train of treatment which will be required to lead the waste to its final destination (i.e., disposal). This approach allows flexibility to manage a wide variety of waste in a cheaper, faster manner than designing a single treatment technology diverse enough to manage all the waste streams

  6. Computer integrated manufacturing in the chemical industry : Theory & practice

    NARCIS (Netherlands)

    Ashayeri, J.; Teelen, A.; Selen, W.J.

    1995-01-01

    This paper addresses the possibilities of implementing Computer Integrated Manufacturing in the process industry, and the chemical industry in particular. After presenting some distinct differences of the process industry in relation to discrete manufacturing, a number of focal points are discussed.

  7. Deactivation of waste waters in the Czechoslovak Uranium Industry

    International Nuclear Information System (INIS)

    Priban, V.

    1978-01-01

    Deactivation techniques are described used for the treatment of waste waters from uranium mines and uranium chemical treatment plants. With treatment plant waters this is done either by precipitation of radium with barium sulfate or using multistage evaporating units. Mine waste waters are deactivated by sorption on ion exchangers; strongly basic anion exchangers, mostly Wofatit SBW, Varion AP or Ostion AU are used for uranium, while the strongly acidic Ostion KS is used for radium. (Z.M.)

  8. Effect of industrial, municipal and agricultural wastes on peanut in lateritic sandy loam soil

    International Nuclear Information System (INIS)

    Sarkar, S.; Khan, A.R.

    2002-06-01

    Modern agriculture, worldwide, depends upon the external application of plant nutrients supplied mostly through chemical fertilizer to meet the crop needs. The natural recycling cannot provide the very large amount of nutrients needed year after year in an intensive cropping system and nutrients being a major constraint harvesting the nutrient energy from biological and industrial waste are of prime importance for maximizing the food grain production in the world. A number of industrial wastes like fly ash from thermal power plants, paper factory sludge from paper factory, sewage sludge from municipal source and farmyard manure from livestock farming are the important waste resources, having potentiality in recycling in agricultural land. When these wastes are recycled through soil for crop production, due to the degradative and assimilative capacity of soil, the pollution hazards of these wastes can be minimized to a greater extent as compared to direct disposing of at the site. Fly ash is a waste product residue resulting from the combustion of pulverised coal in coal-fired power generating station. Physico - chemical analysis of fly ash has revealed the presence of both macro-micro nutrients, which can sustain plant growth. Its application in the agricultural land acts as a liming material and improves crop growth by neutralizing the soil acidity, increasing the water availability for the plants and supplement of nutrients (Adriano et al, 1980, Molliner and Street, 1982, Schnappinger et al, 1975). Application of paper factory sludge has been reported to increase the organic carbon content in soil and nutrient content like P, K, Ca, Mg and micronutrients (Guerini et al, 1994, Muse and Mitchell, 1995). Sludge application also improves the organic carbon content of the soil and availability of nutrients like Ca, K and Mg besides improvement of physical properties (Pitchel and Hayes, 1990). Much is known regarding crop performance and changes in physical and

  9. Chemical industrial areas and their dynamic danger behaviour

    NARCIS (Netherlands)

    Reniers, Genserik L L; Audenaert, Amaryllis; Dullaert, W.; Soudan, K.

    2007-01-01

    Chemical industrial areas or so-called chemical clusters consist of various companies situated next to each other. Such areas are composed of hundreds of chemical installations exhibiting danger to a certain degree for initiating or continuing knock-on effects. In this paper, a methodology to model

  10. The U.S. Chemical Industry, the Products It Makes

    Science.gov (United States)

    Chemical and Engineering News, 1972

    1972-01-01

    This section of the annual report on the chemical industry presents data on these areas of chemical production: growth rates, man-made fibers; the 50 largest volume chemicals, major inorganics and organics, plastics, drugs, magnesium, and paint. Includes production figures for 1961, 1969, 1970, 1971 and percent change for 1970-71 and for 1961-71.…

  11. Hazardous waste management in Chilean main industry: An overview

    International Nuclear Information System (INIS)

    Navia, Rodrigo; Bezama, Alberto

    2008-01-01

    The new 'Hazardous Waste Management Regulation' was published in the Official Newspaper of the Chilean Republic on 12 June 2003, being in force 365 days after its publication (i.e., 12 June 2004). During the next 180 days after its publication (i.e., until 12 December 2004), each industrial facility was obligated to present a 'Hazardous Waste Management Plan' if the facility generates more than 12 ton/year hazardous wastes or more than 12 kg/year acute toxic wastes. Based on the Chilean industrial figures and this new regulation, hazardous waste management plans were carried out in three facilities of the most important sectors of Chilean industrial activity: a paper production plant, a Zn and Pb mine and a sawmill and wood remanufacturing facility. Hazardous wastes were identified, classified and quantified in all facilities. Used oil and oil-contaminated materials were determined to be the most important hazardous wastes generated. Minimization measures were implemented and re-use and recycling options were analyzed. The use of used oil as alternative fuel in high energy demanding facilities (i.e., cement facilities) and the re-refining of the used oil were found to be the most suitable options. In the Zn and Pb mine facility, the most important measure was the beginning of the study for using spent oils as raw material for the production of the explosives used for metals recovery from the rock. In Chile, there are three facilities producing alternative fuels from used oil, while two plants are nowadays re-refining oil to recycle it as hydraulic fluid in industry. In this sense, a proper and sustainable management of the used oil appears to be promissory

  12. Physico-chemical characterisation of material fractions in household waste

    DEFF Research Database (Denmark)

    Götze, Ramona; Boldrin, Alessio; Scheutz, Charlotte

    2016-01-01

    State-of-the-art environmental assessment of waste management systems rely on data for the physico-chemical composition of individual material fractions comprising the waste in question. To derive the necessary inventory data for different scopes and systems, literature data from different sources...... and backgrounds are consulted and combined. This study provides an overview of physico-chemical waste characterisation data for individual waste material fractions available in literature and thereby aims to support the selection of data fitting to a specific scope and the selection of uncertainty ranges related...... to the data selection from literature. Overall, 97 publications were reviewed with respect to employed characterisation method, regional origin of the waste, number of investigated parameters and material fractions and other qualitative aspects. Descriptive statistical analysis of the reported physico...

  13. Plating Plant Waste Utilization in Glasswork, Ceramic and Building Industry

    International Nuclear Information System (INIS)

    Nikolaev, V.P.; Scheglov, M.; Korneva, S.A.

    1999-01-01

    The technology allows using electroplating plant waste for recovery of fine inorganic pigments, which may be used in paintwork and ceramic industry (for coating and enamel preparation, for ceramic painting), in glasswork (colored glass) and in building industry (for producing foundation slabs, sidewalk plates and curbing, for art urban planning, for pavement and aerodrome covering and so on). For fine inorganic pigment recovery so-called sol-gel method was used

  14. Analytical characterization of an industrial waste treated by gasification

    Energy Technology Data Exchange (ETDEWEB)

    Washington, M.D.; Larsen, D.W.; Manahan, S.E. [University of Missouri-St. Louis, St. Louis, MO (United States). Chemistry Dept.

    1999-04-15

    Previous studies have shown that an effective general treatment for hazardous wastes is sorption of the waste onto a specially prepared, macroporous coal char followed by gasification of the mixture in reverse mode. In the present study, an industrial waste comprised of styrene manufacturing and petroleum byproducts was gasified, and the waste, coal, virgin char, and char/waste mixture (before and after gasification) were examined by various instrumental methods, infrared, nuclear magnetic resonance, gas chromatography, gas chromatography/mass spectroscopy, scanning electron microscopy, and ultimate and proximate analyses, to determine which methods give useful information. The composition of the waste was found to be 38% water, 27% inorganic, and 35% organic. NMR showed that the organic components are a mixture of aliphatic and olefinic/aromatics. About 8% of the sludge is chromatographable and GC/MS revealed the presence of aromatics and polyaromatic hydrocarbons. Solid-state NMR showed that the sludge components are strongly immobilized on the char up to a 1:1 (wt:wt) ratio. SEM results showed changes in the char macroporous surface as waste is incorporated by the char and as the mixture is subsequently gasified. In addition, a portion of the elemental content of the char surface was revealed by energy dispersive (EDAX) measurements. IR photoaccoustic spectroscopy showed that peaks attributable to aqueous and organic fractions of the waste disappear upon gasification. 19 refs., 7 figs., 5 tabs.

  15. Milestones in 150 years of the chemical industry

    International Nuclear Information System (INIS)

    Morris, P.J.T.; Campbell, W.A.; Roberts, H.L.

    1991-01-01

    Milestones in 150 years of the Chemical Industry charts the history of the industry in its crucial role of meetings basic human needs. The book provides on overview of developments in the industry in the fields of health, clothing, energy, materials and information technology and sets the information in an historical context. It will be of interest to chemists in industry, academic, business and to the lay public. (author)

  16. Opportunities, perspectives and limits in lactic acid production from waste and industrial by-products

    Directory of Open Access Journals (Sweden)

    Mladenović Dragana D.

    2016-01-01

    Full Text Available In line with the goals of sustainable development and environmental protection today great attention is directed towards new technologies for waste and industrial by-products utilization. Waste products represent potentially good raw material for production other valuable products, such as bioethanol, biogas, biodiesel, organic acids, enzymes, microbial biomass, etc. Since the first industrial production to the present, lactic acid has found wide application in food, cosmetic, pharmaceutical and chemical industries. In recent years, the demand for lactic acid has been increasing considerably owing to its potential use as a monomer for the production of poly-lactic acid (PLA polymers which are biodegradable and biocompatible with wide applications. Waste and industrial by-products such are whey, molasses, stillage, waste starch and lignocellulosic materials are a good source of fermentable sugars and many other substances of great importance for the growth of microorganisms, such as proteins, minerals and vitamins. Utilization of waste products for production of lactic acid could help to reduce the total cost of lactic acid production and except the economic viability of the process offers a solution of their disposal. Fermentation process depends on chemical and physical nature of feedstocks and the lactic acid producer. This review describes the characteristics, abilities and limits of microorganisms involved in lactic acid production, as well as the characteristics and types of waste products for lactic acid production. The fermentation methods that have been recently reported to improve lactic acid production are summarized and compared. In order to improve processes and productivity, fed-batch fermentation, fermentation with immobilized cell systems and mixed cultures and opportunities of open (non-sterilized fermentation have been investigated.

  17. Glasses obtained from industrial wastes; Vidros obtidos a partir de residuos industriais

    Energy Technology Data Exchange (ETDEWEB)

    Bortoluzzi, D.; Oliveira Fillho, J.; Uggioni, E. [Universidade do Extremo Sul Catarinense (UNESC), Criciuma, SC (Brazil). Curso de Engenharia de Materiais; Bernardin, A.M., E-mail: amb@unesc.ne [Servico Nacional de Aprendizagem Industrial (SENAI), Tijucas, SC (Brazil). Tecnologia em Ceramica

    2009-07-01

    This paper deals with the study of the vitrification mechanism as an inertization method for industrial wastes contaminated with heavy metals. Ashes from coal (thermoelectric), wastes from mining (fluorite and feldspar) and plating residue were used to compose vitreous systems planed by mixture design. The chemical composition of the wastes was determined by XRF and the formulations were melted at 1450 deg C for 2h using 10%wt of CaCO{sub 3} (fluxing agent). The glasses were poured into a mold and annealed (600 deg C). The characteristic temperatures were determined by thermal analysis (DTA, air, 20 deg C/min) and the mechanical behavior by Vickers microhardness. As a result, the melting temperature is strongly dependent on silica content of each glass, and the fluorite residue, being composed mainly by silica, strongly affects Tm. The microhardness of all glasses is mainly affected by the plating residue due to the high iron and zinc content of this waste. (author)

  18. Chemical durability of glasses containing radioactive fission product waste

    International Nuclear Information System (INIS)

    Mendel, J.E.; Ross, W.A.

    1974-04-01

    Measurements made to determine the chemical durability of glasses for disposal of radioactive waste are discussed. The term glass covers materials varying from true glass with only minute quantities of crystallites, such as insoluble RuO 2 , to quasi glass-ceramics which are mostly crystalline. Chemical durability requirements and Soxhlet extractor leach tests are discussed

  19. Genotoxicity monitoring of industrial wastes using plant bioassays and management through vermitechnology: A review

    Directory of Open Access Journals (Sweden)

    Sartaj Ahmad Bhat

    2017-10-01

    Full Text Available The main objective of this review was to summarize and present a comprehensive account of the cytotoxic, genotoxic and mutagenic potential of various industrial wastes/sludges using some well-known plant bioassays followed by their bioremediation using vermitechnology. Industries are the main origin of discharges of various types of chemical wastes and are the main causes of environmental degradation. The direct application of industrial sludges could also harm the local biota. The genotoxicity of industrial sludges is assessed using various plant bioassays (for example Allium cepa, Vicia faba and these bioassays are comparatively more sensitive and cost-effective compared to other in-vitro genotoxicity bioassays. In addition, the materials used for toxicity evaluation are easily available and are being routinely used for the monitoring of environmental pollution. In most studies, the increases in root length and mitotic index, as well as the decrease in chromosomal aberrations in post vermicomposted sludges/wastes indicate that earthworms have the ability to reduce the ecotoxicogenetic effects of sludges/wastes. Post vermicompost is considered an excellent material of a homogenous nature as it has reduced levels of contaminants and holds more nutrients over a longer time without affecting the environment. The biotransformation potential of earthworms and their ability to detoxify most of the heavy metals in industrial sludges is because of their strong metabolic system and the involvement of diverse intestinal microflora and chloragocytic cells that reduce toxic forms to nontoxic forms. This unique ability of earthworms confirms the effectiveness of vermitechnology in reducing the toxicity of industrial wastes. Keywords: Allium cepa, Earthworm, Industrial sludge, Toxicity, Vermicomposting

  20. Biotreatment of industrial and hazardous waste

    International Nuclear Information System (INIS)

    Levin, M.A.; Gealt, M.A.

    1993-01-01

    This book attempts to approach the topic of biodegradation of hazardous wastes in a holistic fashion. The issues of science, engineering and regulation are all addressed. As much as possible, both theoretical and practical considerations have been dealt with. Selection of bacteria for the specific purpose of degrading compounds is discussed at the bench-scale to the field level. Engineering theory as applied to growth on toxic substances is discussed. The legal issues are covered. There are also several examples of field studies indicating the current usage of biodegradation, both within reactors and in situ. The use of biodegradation is compared with other mechanisms of disposal, in terms of time limitations, degradation limitations and, perhaps most important, cost. Individual papers have been processed separately for inclusion in the appropriate data bases

  1. Applicability of federal and state hazardous waste regulatory programs to waste chemical weapons and chemical warfare agents.; TOPICAL

    International Nuclear Information System (INIS)

    Haffenden, R.; Kimmell, T.

    2002-01-01

    This report reviews federal and state hazardous waste regulatory programs that govern the management of chemical weapons or chemical warfare agents. It addresses state programs in the eight states with chemical weapon storage facilities managed by the U.S. Army: Alabama, Arkansas, Colorado, Indiana, Kentucky, Maryland, Oregon, and Utah. It also includes discussions on 32 additional states or jurisdictions with known or suspected chemical weapons or chemical warfare agent presence (e.g., disposal sites containing chemical agent identification sets): Alaska, Arizona, California, Florida, Georgia, Hawaii, Idaho, Illinois, Iowa, Kansas, Louisiana, Massachusetts, Michigan, Mississippi, Missouri, Nebraska, Nevada, New Jersey, New Mexico, New York, North Carolina, Ohio, Pennsylvania, South Carolina, South Dakota, Tennessee, Texas, the U.S. Virgin Islands, Virginia, Washington, Washington, D.C., and Wyoming. Resource Conservation and Recovery Act (RCRA) hazardous waste programs are reviewed to determine whether chemical weapons or chemical warfare agents are listed hazardous wastes or otherwise defined or identified as hazardous wastes. Because the U.S. Environmental Protection Agency (EPA) military munitions rule specifically addresses the management of chemical munitions, this report also indicates whether a state has adopted the rule and whether the resulting state regulations have been authorized by EPA. Many states have adopted parts or all of the EPA munitions rule but have not yet received authorization from EPA to implement the rule. In these cases, the states may enforce the adopted munitions rule provisions under state law, but these provisions are not federally enforceable

  2. Radiological and chemical source terms for Solid Waste Operations Complex

    International Nuclear Information System (INIS)

    Boothe, G.F.

    1994-01-01

    The purpose of this document is to describe the radiological and chemical source terms for the major projects of the Solid Waste Operations Complex (SWOC), including Project W-112, Project W-133 and Project W-100 (WRAP 2A). For purposes of this document, the term ''source term'' means the design basis inventory. All of the SWOC source terms involve the estimation of the radiological and chemical contents of various waste packages from different waste streams, and the inventories of these packages within facilities or within a scope of operations. The composition of some of the waste is not known precisely; consequently, conservative assumptions were made to ensure that the source term represents a bounding case (i.e., it is expected that the source term would not be exceeded). As better information is obtained on the radiological and chemical contents of waste packages and more accurate facility specific models are developed, this document should be revised as appropriate. Radiological source terms are needed to perform shielding and external dose calculations, to estimate routine airborne releases, to perform release calculations and dose estimates for safety documentation, to calculate the maximum possible fire loss and specific source terms for individual fire areas, etc. Chemical source terms (i.e., inventories of combustible, flammable, explosive or hazardous chemicals) are used to determine combustible loading, fire protection requirements, personnel exposures to hazardous chemicals from routine and accident conditions, and a wide variety of other safety and environmental requirements

  3. The impact of industrial waste of Venezuelan marine water

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, Frank [Bechtel Corp., Gaithersburg, MD (United States); Guarino, Carmen [Guarino Engineers, Philadelphia, PA (United States); Arias, Marlene [Ministerio del Ambiente y Recursos Naturales Renovables, Caracas (Venezuela)

    1993-12-31

    The Puerto Cabello-Marron coastal area of Venezuela is an ideal location for industries that require large land areas, water, marine transportation, minimum habitation, cooling water, etc. However, mercury spills have produced concern in the entire coastal zone. The area was investigated and negative impacts were identified. Consequently, recommendations for waste water management were proceeded. 13 refs., 6 figs., 3 tabs.

  4. Thermoexoemission detectors for monitoring radioactive contamination of industrial waste waters

    International Nuclear Information System (INIS)

    Obukhov, V.T.; Sobolev, I.A.; Khomchik, L.M.

    1987-01-01

    Detectors on base of BeO(Na) monocrystals with thermoemission to be used for monitoring radioactive contamination of industrial waste waters are suggested. The detectors advantages are sensitivity to α and low-ehergy β radiations, high mechanical strength and wide range of measurements. The main disadvantage is the necessity of working in red light

  5. The impact of industrial waste of Venezuelan marine water

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, Frank [Bechtel Corp., Gaithersburg, MD (United States); Guarino, Carmen [Guarino Engineers, Philadelphia, PA (United States); Arias, Marlene [Ministerio del Ambiente y Recursos Naturales Renovables, Caracas (Venezuela)

    1994-12-31

    The Puerto Cabello-Marron coastal area of Venezuela is an ideal location for industries that require large land areas, water, marine transportation, minimum habitation, cooling water, etc. However, mercury spills have produced concern in the entire coastal zone. The area was investigated and negative impacts were identified. Consequently, recommendations for waste water management were proceeded. 13 refs., 6 figs., 3 tabs.

  6. Optimization of process for creating porous structure of materials from industrial waste

    International Nuclear Information System (INIS)

    Mangutova-Stoilkovska, Bianka

    2005-01-01

    Republic of Macedonia, as many European countries, possesses great quantities of industrial waste materials from thermo electrical power stations and metallurgical capacities. The powder from waste fly ash and metallurgical slag was specified from chemical, geometrical, structural and thermochemical aspects. After the consolidation, the compacts were specified from structural, mechanical and thermophysical aspects. Using three kinds of waste glasses (TV glass, window and flask), the sintering temperature was significantly reduced and ecologically risky components were fixed molecularly in the matrix based on fly ash and metallurgical slag. The glass was characterized from chemical, geometrical and thermophysical point of view. The amount of glass in the composites varied from 10%-50%. The mechanical and thermal expansion properties of the sintered compacts, in the temperature region from 800 o -1200 o C were determined. The thermodynamic stability, mechanical properties and chemical inertness have been used as criterion for selection of the consolidated compacts. Special attention was given to the creation of highly porous structure. For the purpose to obtain a high joint porous structure, several types of porosity have been used: polyurethane foam, hydrogen peroxide, limestone, carbon ash and carbon fibres. The obtained glass-ceramic materials could be used in the building industry, for making filters for gases and liquids as well as diffusers for waste water aeration. (Author)

  7. Resilience of chemical industrial areas through attenuation-based security

    International Nuclear Information System (INIS)

    Reniers, G.L.L.; Sörensen, K.; Khan, F.; Amyotte, P.

    2014-01-01

    This paper investigates the possibility of attenuation-based security within chemical industrial areas. Representing chemical industrial areas as mathematical networks, we prove by case-study that the resilience to disaster of such areas may follow a power-law distribution. Furthermore, we examine what happens to the network when highly hazardous installations would be intelligently protected against malicious acts: the network disintegrates into separate smaller networks. Hence, islands are formed with no escalation danger in between. We conclude that it is possible to protect chemical industrial areas in such a way that they are more resilient against terrorism

  8. Direction of CRT waste glass processing: Electronics recycling industry communication

    International Nuclear Information System (INIS)

    Mueller, Julia R.; Boehm, Michael W.; Drummond, Charles

    2012-01-01

    Highlights: ► Given a large flow rate of CRT glass ∼10% of the panel glass stream will be leaded. ► The supply of CRT waste glass exceeded demand in 2009. ► Recyclers should use UV-light to detect lead oxide during the separation process. ► Recycling market analysis techniques and results are given for CRT glass. ► Academic initiatives and the necessary expansion of novel product markets are discussed. - Abstract: Cathode Ray Tube, CRT, waste glass recycling has plagued glass manufacturers, electronics recyclers and electronics waste policy makers for decades because the total supply of waste glass exceeds demand, and the formulations of CRT glass are ill suited for most reuse options. The solutions are to separate the undesirable components (e.g. lead oxide) in the waste and create demand for new products. Achieving this is no simple feat, however, as there are many obstacles: limited knowledge of waste glass composition; limited automation in the recycling process; transportation of recycled material; and a weak and underdeveloped market. Thus one of the main goals of this paper is to advise electronic glass recyclers on how to best manage a diverse supply of glass waste and successfully market to end users. Further, this paper offers future directions for academic and industry research. To develop the recommendations offered here, a combination of approaches were used: (1) a thorough study of historic trends in CRT glass chemistry; (2) bulk glass collection and analysis of cullet from a large-scale glass recycler; (3) conversations with industry members and a review of potential applications; and (4) evaluation of the economic viability of specific uses for recycled CRT glass. If academia and industry can solve these problems (for example by creating a database of composition organized by manufacturer and glass source) then the reuse of CRT glass can be increased.

  9. Vulnerability assessment of chemical industry facilities in South Korea based on the chemical accident history

    Science.gov (United States)

    Heo, S.; Lee, W. K.; Jong-Ryeul, S.; Kim, M. I.

    2016-12-01

    The use of chemical compounds are keep increasing because of their use in manufacturing industry. Chemical accident is growing as the consequence of the chemical use increment. Devastating damages from chemical accidents are far enough to aware people's cautious about the risk of the chemical accident. In South Korea, Gumi Hydrofluoric acid leaking accident triggered the importance of risk management and emphasized the preventing the accident over the damage reducing process after the accident occurs. Gumi accident encouraged the government data base construction relate to the chemical accident. As the result of this effort Chemical Safety-Clearing-house (CSC) have started to record the chemical accident information and damages according to the Harmful Chemical Substance Control Act (HCSC). CSC provide details information about the chemical accidents from 2002 to present. The detail informations are including title of company, address, business type, accident dates, accident types, accident chemical compounds, human damages inside of the chemical industry facilities, human damage outside of the chemical industry facilities, financial damages inside of the chemical industry facilities, and financial damages outside of the chemical industry facilities, environmental damages and response to the chemical accident. Collected the chemical accident history of South Korea from 2002 to 2015 and provide the spatial information to the each accident records based on their address. With the spatial information, compute the data on ArcGIS for the spatial-temporal analysis. The spatial-temporal information of chemical accident is organized by the chemical accident types, damages, and damages on environment and conduct the spatial proximity with local community and environmental receptors. Find the chemical accident vulnerable area of South Korea from 2002 to 2015 and add the vulnerable area of total period to examine the historically vulnerable area from the chemical accident in

  10. Solutions for energy recovery of animal waste from leather industry

    International Nuclear Information System (INIS)

    Lazaroiu, Gheorghe; Pană, Constantin; Mihaescu, Lucian; Cernat, Alexandru; Negurescu, Niculae; Mocanu, Raluca; Negreanu, Gabriel

    2017-01-01

    Highlights: • Animal fats in blend with diesel fuel for energy valorification through combustion. • Animal waste from tanneries as fuel and for biogas production. • Experimental tests using animal fats as fuel for diesel engines. • Experimental tests modifying the characteristic parameters. - Abstract: Secondary products from food and leather industries are regarded as animal wastes. Conversion of these animal wastes into fuels represents an energy recovery solution not only because of their good combustion properties, but also from the viewpoint of supply stability. A tannery factory usually processes 60–70 t/month of crude leathers, resulting in 12–15 t/month of waste. Fats, which can be used as the input fuel for diesel engines (in crude state or as biodiesel), represent 10% of this animal waste, while the rest are proteins that can be used to generate biogas through anaerobic digestion. Herein, we analyse two approaches to the use of animal waste from tanneries: as fuel for diesel engines and for biogas generation for heat production. Diesel fuelling and fuelling by animal wastes are compared in terms of the engine performance and pollutant emissions. The effects of animal waste usage on the pollutant emissions level, exhaust gas temperature, indicated mean effective pressure, maximum pressure, and engine efficiency are analysed. The energy recovery technologies for animal waste, which are analysed in this work, can be easily implemented and can simultaneously solve the problem posed by animal wastes by using them as an alternative to fossil fuels. Animal fats can be considered an excellent alternative fuel for diesel engines without major constructive modifications.

  11. Safety in the Chemical Laboratory: Chemical Wastes in Academic Labs.

    Science.gov (United States)

    Walton, Wendy A.

    1987-01-01

    Encourages instruction about disposal of hazardous wastes in college chemistry laboratories as an integral part of experiments done by students. Discusses methods such as down-the-drain disposal, lab-pack disposal, precipitation and disposal, and precipitation and recovery. Suggests that faculty and students take more responsibility for waste…

  12. Industrial waste treatment: the leather industry; Tratamiento conjunto de aguas residuales e industriales: caso de las industrias del curtido

    Energy Technology Data Exchange (ETDEWEB)

    Cortacans Torre, J.A.

    1995-07-01

    The industrial waste water treatment can be presented alone or together with the urban waste water. There are special industries that cannot treat their effluents together with municipal effluents, for example the leather industry. This industry uses sulfurs and equivalent chromium. The PH value is around 10. This waste water can`t be introduce directly into municipal collectors. This article presents the general recommendations for their treatment.

  13. Industrial Program of Waste Management - Cigeo Project - 13033

    Energy Technology Data Exchange (ETDEWEB)

    Butez, Marc [Agence nationale pour la gestion des dechets radioactifs - Andra, 1-7, rue Jean Monnet 92298 Chatenay-Malabry (France); Bartagnon, Olivier; Gagner, Laurent [AREVA NC Tour AREVA 1 place de la Coupole 92084 Paris La Defense (France); Advocat, Thierry; Sacristan, Pablo [Commissariat a l' energie atomique et aux energies alternatives - CEA, CEA-SACLAY 91191 Gif sur Yvette Cedex (France); Beguin, Stephane [Electricite de France - EDF, Division Combustible Nucleaire, 1, Place Pleyel Site Cap Ampere93282 Saint Denis (France)

    2013-07-01

    The French Planning Act of 28 June 2006 prescribed that a reversible repository in a deep geological formation be chosen as the reference solution for the long-term management of high-level and intermediate-level long-lived radioactive waste. It also entrusted the responsibility of further studies and design of the repository (named Cigeo) upon the French Radioactive Waste Management Agency (Andra), in order for the review of the creation-license application to start in 2015 and, subject to its approval, the commissioning of the repository to take place in 2025. Andra is responsible for siting, designing, implementing, operating the future geological repository, including operational and long term safety and waste acceptance. Nuclear operators (Electricite de France (EDF), AREVA NC, and the French Commission in charge of Atomic Energy and Alternative Energies (CEA) are technically and financially responsible for the waste they generate, with no limit in time. They provide Andra, on one hand, with waste packages related input data, and on the other hand with their long term industrial experiences of high and intermediate-level long-lived radwaste management and nuclear operation. Andra, EDF, AREVA and CEA established a cooperation agreement for strengthening their collaborations in these fields. Within this agreement Andra and the nuclear operators have defined an industrial program for waste management. This program includes the waste inventory to be taken into account for the design of the Cigeo project and the structural hypothesis underlying its phased development. It schedules the delivery of the different categories of waste and defines associated flows. (authors)

  14. Industrial Program of Waste Management - Cigeo Project - 13033

    International Nuclear Information System (INIS)

    Butez, Marc; Bartagnon, Olivier; Gagner, Laurent; Advocat, Thierry; Sacristan, Pablo; Beguin, Stephane

    2013-01-01

    The French Planning Act of 28 June 2006 prescribed that a reversible repository in a deep geological formation be chosen as the reference solution for the long-term management of high-level and intermediate-level long-lived radioactive waste. It also entrusted the responsibility of further studies and design of the repository (named Cigeo) upon the French Radioactive Waste Management Agency (Andra), in order for the review of the creation-license application to start in 2015 and, subject to its approval, the commissioning of the repository to take place in 2025. Andra is responsible for siting, designing, implementing, operating the future geological repository, including operational and long term safety and waste acceptance. Nuclear operators (Electricite de France (EDF), AREVA NC, and the French Commission in charge of Atomic Energy and Alternative Energies (CEA) are technically and financially responsible for the waste they generate, with no limit in time. They provide Andra, on one hand, with waste packages related input data, and on the other hand with their long term industrial experiences of high and intermediate-level long-lived radwaste management and nuclear operation. Andra, EDF, AREVA and CEA established a cooperation agreement for strengthening their collaborations in these fields. Within this agreement Andra and the nuclear operators have defined an industrial program for waste management. This program includes the waste inventory to be taken into account for the design of the Cigeo project and the structural hypothesis underlying its phased development. It schedules the delivery of the different categories of waste and defines associated flows. (authors)

  15. Guidelines for generators of hazardous chemical waste at LBL and Guidelines for generators of radioactive and mixed waste at LBL

    International Nuclear Information System (INIS)

    1991-07-01

    The purpose of this document is to provide the acceptance criteria for the transfer of hazardous chemical, radioactive, and mixed waste to Lawrence Berkeley Laboratory's (LBL) Hazardous Waste Handling Facility (HWHF). These guidelines describe how a generator of wastes can meet LBL's acceptance criteria for hazardous chemical, radioactive, and mixed waste. 9 figs

  16. Dilute chemical decontamination resins and the mixed waste issue

    International Nuclear Information System (INIS)

    Denault, R.P.; Hallman, J.T.

    1988-01-01

    The decontamination of reactor primary systems, sub-systems and components is an important method used to reduce the occupational radiation exposure of nuclear plant personnel. The waste produced by the application of this technology is mainly solid in the form of ion exchange resins. As a result of a recent agreement between the Environmental Protection Agency (EPA) and the Nuclear Regulatory Commission (NRC), all radioactive waste must meet EPA burial criteria. The chemicals used in a decontamination and certain metals dissolved during the process, primarily chromium, could render the waste hazardous as well as radioactive or more commonly called a mixed waste. This paper defines mixed waste as described in the EPA directive 9432.00-2, and examine the criteria by which waste is categorized as hazardous. The decontamination waste resin generated by two processes, the CAN-DEREM and the LOMI process, is described in detail. Waste data obtained from decontaminations performed by LN Technologies Corporation including chemical, metal and radionuclide loadings on resins from both PWR and BWR applications are presented

  17. A waste to energy plant for an industrial districts

    International Nuclear Information System (INIS)

    Floreani, M.; Meneghetti, A.; Nardin, G.; Rocco, A.

    2001-01-01

    Industrial districts show characteristics that can be exploited by developing plant solutions studied for their special configuration and not simply extended from single unit models. In the paper a waste-to-energy plant for the chair industrial district in Friuli Venezia Giulia (North Eastern Italy) is described. It has been designed directly involving the University of Udine and can be considered an example of how technology innovation can be promoted by universities, especially in the case of small firms which have limited R and D resources. It is shown how industrial refuse becomes a chance of competitive advantage for the whole district due to its energy recovery in a plant unique for the type of waste processed. Input, combustion, energy recovery and cleaning sections are described in details, underlining innovative approaches and solutions [it

  18. Profile of the chemicals industry in California: Californiaindustries of the future program

    Energy Technology Data Exchange (ETDEWEB)

    Galitsky, Christina; Worrell, Ernst

    2004-06-01

    The U.S. Department of Energy (DOE) Office of Industrial Technologies (OIT) established the Industries of the Future (IOF) program to increase energy efficiency, reduce waste production and to improve competitiveness, currently focusing on nine sectors. The IOF is a partnership strategy involving industry, the research community and the government, working together to identify technology needs, promote industrial partnerships and implement joint measures with all partners involved. The State Industries of the Future (SIOF) program delivers the accomplishments of the national Industries of the Future strategy to the local level, to expand the technology opportunities to a larger number of partners and reach smaller businesses and manufacturers that were not initially involved in the IOF effort. The state programs bring together industry, academia, and state agencies to address the important issues confronting industry in the state. These public-private coalitions facilitate industry solutions locally and enhance economic development. California has started a State Industries of the Future effort, in collaboration with the U.S. Department of Energy. The California Energy Commission (CEC) is leading the SIOF program in California, as part of many other programs to improve the energy efficiency and performance of industries in California. The California State IOF program aims to build a network of participants from industry, academia and government in four selected industrial sectors as a basis for the development of a strategic partnership for industrial energy efficient technology in the state. In California the IOF effort focuses petroleum refining, chemical processing, food processing and electronics. As part of this effort, the SIOF program will develop roadmaps for technology development for the selected sectors. On the basis of the roadmap, the program will develop successful projects with co-funding from state and federal government, and promote industry

  19. Creative research in the chemical industry

    Indian Academy of Sciences (India)

    These efforts have involved several collaborators including many from other institutions and offered multitudinous challenges calling for continuous creativity in industrial setups. I was fortunate to have had a conducive environment to be able to respond to these challenges. I attempt to offer the readers in the ensuing pages ...

  20. Biobased industrial chemicals from glutamic acid

    NARCIS (Netherlands)

    Lammens, T.M.

    2011-01-01

    In dit onderzoek is op zoek gegaan naar routes om van glutaminezuur vier producten te maken die van waarde zijn voor de industrie, die nu uit olie gemaakt worden. Dat zijn grondstoffen voor allerlei soorten kunststof, zoals nylon en rubbers. Het onderzoek laat zien dat alle vier die producten

  1. Sublethal effects of industrial chemicals on fish fingerlings (Tilapia ...

    African Journals Online (AJOL)

    STORAGESEVER

    2010-03-22

    Mar 22, 2010 ... Key words: Tilapia guineensis, industrial chemical, bioaccumulation, surfactants. ... product that has acceptable stability in oil pipelines. (Patton, 1995). .... assays were assessed with the two-factor ANOVA (analysis of.

  2. Anaerobic digestion of solid slaughterhouse waste chemically pretreated

    Energy Technology Data Exchange (ETDEWEB)

    Flores, C.; Montoya, L.; Rodirguez, A.

    2009-07-01

    One of the mayor problems facing the industrialized world today is to solve environmental contamination and identify efficient treatment to give solution to the current problems like the generation of enormous quantities of liquid and solid wastes. The solid slaughterhouse waste, due to its elevated concentration of biodegradable organics, can be efficiently treated by anaerobic digestion although the high content of lignocellulose materials, makes it a slowly process. (Author)

  3. Anaerobic digestion of solid slaughterhouse waste chemically pretreated

    International Nuclear Information System (INIS)

    Flores, C.; Montoya, L.; Rodirguez, A.

    2009-01-01

    One of the mayor problems facing the industrialized world today is to solve environmental contamination and identify efficient treatment to give solution to the current problems like the generation of enormous quantities of liquid and solid wastes. The solid slaughterhouse waste, due to its elevated concentration of biodegradable organics, can be efficiently treated by anaerobic digestion although the high content of lignocellulose materials, makes it a slowly process. (Author)

  4. Cleaner production options for reducing industrial waste: the case of batik industry in Malang, East Java-Indonesia

    Science.gov (United States)

    Sirait, M.

    2018-01-01

    The aim of this research is to conduct cleaner production options for improving the environmental performance during the production of batik industry, the case of UKM batik, Malang, East Java. Batik industry is one of small and medium textile industry which has contribution to economic growth in Malang. However, during production the batik, it generates wastewater that has potential to decrease the environmental performance. Wastewater from Celaket batik industry has BOD, COD, TSS, and pH level is far larger than the threshold of water quality standard as a result of use chemical substance during the dyes processing. In order to prevent generating wastewater, this study utilized cleaner production options, such as substitution of input material.Substitution of input material for dyes process was implemented by replacement chemical dyes (e.g.indigosol, nafthol, rapid) with natural dyes (e.g. Indigofero Tintoria). Modifying of technology/equipment was conducted by developing wastewater treatment equipment to reduce waste of batik production. The implementation of this strategy was carried out by changing input material from chemical dyes with natural dyes. The CP uptake could reduce significantly the environmental impact in term of reduction of COD, BOD, and TSS.

  5. Fate of chemical warfare agents and toxic industrial chemicals in landfills.

    Science.gov (United States)

    Bartelt-Hunt, Shannon L; Barlaz, Morton A; Knappe, Detlef R U; Kjeldsen, Peter

    2006-07-01

    One component of preparedness for a chemical attack is planning for the disposal of contaminated debris. To assess the feasibility of contaminated debris disposal in municipal solid waste (MSW) landfills, the fate of selected chemical warfare agents (CWAs) and toxic industrial chemicals (TICs) in MSW landfills was predicted with a mathematical model. Five blister agents [sulfur mustard (HD), nitrogen mustard (HN-2), lewisite (L), ethyldichloroarsine (ED), and phosgene oxime (CX)], eight nerve agents [tabun (GA), sarin (GB), soman (GD), GE, GF, VX, VG, and VM], one riot-control agent [CS], and two TICs [furan and carbon disulfide] were studied. The effects of both infiltration (climate) and contaminant biodegradability on fate predictions were assessed. Model results showed that hydrolysis and gas-phase advection were the principal fate pathways for CWAs and TICs, respectively. Apart from CX and the TICs, none of the investigated compounds was predicted to persist in a landfill for more than 5 years. Climate had little impact on CWA/TIC fate, and biodegradability was only important for compounds with long hydrolysis half-lives. Monte Carlo simulations were performed to assess the influence of uncertainty in model input parameters on CWA/TIC fate predictions. Correlation analyses showed that uncertainty in hydrolysis rate constants was the primary contributor to variance of CWA fate predictions, while uncertainty in the Henry's Law constant and landfill gas-production rate accounted for most of the variance of TIC fate predictions. CWA hydrolysates were more persistent than the parent CWAs, but limited information is available on abiotic or biotic transformation rates for these chemicals.

  6. Membrane technology: in the chemical industry

    National Research Council Canada - National Science Library

    Nunes, S. P; Peinemann, K. V

    2001-01-01

    ... terephthalate) 15 22 23 32 37 5 5.1 5.2 5.3 5.4 Surface Modification of Membranes Chemical Oxidation 39 Plasma Treatment 40 Classical Organic Reactions 41 Polymer Grafting 41 39VI Contents 6 6.1 ...

  7. Accidents in chemical industry: are they foreseeable?

    NARCIS (Netherlands)

    Sonnemans, P.J.M.; Körvers, P.M.W.

    2006-01-01

    ‘Accidents recur,’ which is what Kletz [Kletz T. (1993). Lessons from disasters, how organisations have no memory and accidents recur. UK: Institution of Chemical Engineers] wrote in 1993. Indeed, despite all measures taken accidents may re-occur, but ‘disruptions’ in a process reoccur much more

  8. The Recovery of Zinc Heavy Metal from Industrial Liquid Waste

    International Nuclear Information System (INIS)

    Panggabean, Sahat M.

    2000-01-01

    It had been studied the recovery of zinc heavy metal from liquid waste of electroplating industry located at East Jakarta. The aim of this study was to minimize the waste arisen from industrial activities by taking out zinc metal in order to reused on-site. The method of recovery was two steps precipitation using NaOH reagent and pH variation. The first step of precipitation at pH optimum around 6 yielded iron metal. The second step at pH optimum around 10 yielded zinc metal. The zinc metal was taken out assessed to the possibility of reused at that fabric. By applying its, it will yield the volume reduction of sludge waste about 36.1% or 53.2% of zinc metal containing in the waste. It means the cost of waste treatment will be lower. Beside its, the effluent arisen from the method had fulfill the maximum limit and it allowed to release to the environment. (author)

  9. Methods for recovering precious metals from industrial waste

    Science.gov (United States)

    Canda, L.; Heput, T.; Ardelean, E.

    2016-02-01

    The accelerated rate of industrialization increases the demand for precious metals, while high quality natural resources are diminished quantitatively, with significant operating costs. Precious metals recovery can be successfully made from waste, considered to be secondary sources of raw material. In recent years, concerns and interest of researchers for more increasing efficient methods to recover these metals, taking into account the more severe environmental protection legislation. Precious metals are used in a wide range of applications, both in electronic and communications equipment, spacecraft and jet aircraft engines and for mobile phones or catalytic converters. The most commonly recovered precious metals are: gold from jewellery and electronics, silver from X- ray films and photographic emulsions, industrial applications (catalysts, batteries, glass/mirrors), jewellery; platinum group metals from catalytic converters, catalysts for the refining of crude oil, industrial catalysts, nitric acid manufacturing plant, the carbon-based catalyst, e-waste. An important aspect is the economic viability of recycling processes related to complex waste flows. Hydrometallurgical and pyrometallurgical routes are the most important ways of processing electrical and electronic equipment waste. The necessity of recovering precious metals has opened new opportunities for future research.

  10. Safety in the Chemical Laboratory--Chemical Management: A Method for Waste Reduction.

    Science.gov (United States)

    Pine, Stanley H.

    1984-01-01

    Discusses methods for reducing or eliminating waste disposal problems in the chemistry laboratory, considering both economic and environmental aspects of the problems. Proposes inventory control, shared use, solvent recycling, zero effluent, and various means of disposing of chemicals. (JM)

  11. Physical and chemical evaluation of furniture waste briquettes.

    Science.gov (United States)

    Moreno, Ana Isabel; Font, Rafael; Conesa, Juan A

    2016-03-01

    Furniture waste is mainly composed of wood and upholstery foam (mostly polyurethane foam). Both of these have a high calorific value, therefore, energy recovery would be an appropriate process to manage these wastes. Nevertheless, the drawback is that the energy content of these wastes is limited due to their low density mainly that of upholstery foam. Densification of separate foam presents difficulties due to its elastic character. The significance of this work lies in obtaining densified material by co-densification of furniture wood waste and polyurethane foam waste. Densification of furniture wood and the co-densification of furniture wood waste with polyurethane foam have been studied. On the one hand, the parameters that have an effect on the quality of the furniture waste briquettes have been analysed, i.e., moisture content, compaction pressure, presence of lignin, etc. The maximum weight percentage of polyurethane foam that can be added with furniture wood waste to obtain durable briquettes and the optimal moisture were determined. On the other hand, some parameters were analysed in order to evaluate the possible effect on the combustion. The chemical composition of waste wood was compared with untreated wood biomass; the higher nitrogen content and the concentration of some metals were the most important differences, with a significant difference of Ti content. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. Environmental technology applications: fact file on toxic contaminants in industrial waste process streams

    Energy Technology Data Exchange (ETDEWEB)

    Newkirk, H.W.

    1977-05-11

    This report is a compendium of facts related to chemical materials present in industrial waste process streams which have already been declared or are being evaluated as hazardous under the Toxic Substances Control Act. Since some 400 chemicals are presently covered by consensus standards, the substances reviewed are only those considered to be a major threat to public health and welfare by Federal and State regulatory agencies. For each hazardous material cited, the facts relate, where possible, to an identification of the stationary industrial sources, the kind of waste stream impacted, proposed regulations and established effluent standards, the volume of emissions produced each year, the volume of emissions per unit of industrial product produced, present clean-up capabilities, limitations, and costs. These data should be helpful in providing information for the assessment of potential problems, should be of use to the manufacturers of pollution control equipment or of chemicals for pollution control, should be of use to the operators or potential operators of processes which produce pollutants, and should help to define industry-wide emission practices and magnitudes.

  13. Employment in the U.S. Chemical Industry. Chemical Work Force Tops 1.1 Million.

    Science.gov (United States)

    Chemical and Engineering News, 1990

    1990-01-01

    The annual census of industrial employment, production workers, women, the workweek, scientists and engineers, chemical employment, wages, and productivity in the chemical industry is presented. Trends in the numbers of workers, productivity, and unit labor costs are illustrated in graphs. (CW)

  14. Industrial long-term waste management in France

    International Nuclear Information System (INIS)

    Marque, Y.

    1988-01-01

    Long-term industrial management of radioactive waste in France is carried out by the Agence Nationale pour la Gestion des Dechets Radioactifs (ANDRA). ANDRA is in charge of design, siting, construction and operation of disposal centers. The French national program of waste management is running on with the construction of a second near-surface disposal which is expected to be in operation in 1991 and a selection of a site for the construction of an underground laboratory for the qualification of this site for deep disposal

  15. Technology for industrial waste heat recovery by organic Rankine cycle systems

    Science.gov (United States)

    Cain, W. G.; Drake, R. L.; Prisco, C. J.

    1984-10-01

    The recovery of industrial waste heat and the conversion thereof to useful electric power by use of Rankine cycle systems is studied. Four different aspects of ORC technology were studied: possible destructive chemical reaction between an aluminum turbine wheel and R-113 working fluid under wheel-to-rotor rub conditions; possible chemical reaction between stainless steel or carbon steel and any of five different ORC working fluids under rotor-stator rub conditions; effects on electric generator properties of extended exposure to an environment of saturated R-113 vapor/fluid; and operational proof tests under laboratory conditions of two 1070 kW, ORC, R-113 hermetic turbogenerator power module systems.

  16. 2011 Annual Industrial Wastewater Reuse Report for the Idaho National Laboratory Site's Materials and Fuels Complex Industrial Waste Ditch and Industrial Waste Pond

    Energy Technology Data Exchange (ETDEWEB)

    David Frederick

    2012-02-01

    This report describes conditions, as required by the state of Idaho Industrial Wastewater Reuse Permit (LA-000160-01), for the wastewater reuse site at the Idaho National Laboratory Site's Materials and Fuels Complex Industrial Waste Ditch and Industrial Waste Pond from November 1, 2010 through October 31, 2011. The report contains the following information: (1) Facility and system description; (2) Permit required effluent monitoring data and loading rates; (3) Groundwater monitoring data; (4) Status of special compliance conditions; and (5) Discussion of the facility's environmental impacts. During the 2011 reporting year, an estimated 6.99 million gallons of wastewater were discharged to the Industrial Waste Ditch and Pond which is well below the permit limit of 13 million gallons per year. Using the dissolved iron data, the concentrations of all permit-required analytes in the samples from the down gradient monitoring wells were below the Ground Water Quality Rule Primary and Secondary Constituent Standards.

  17. Industrial wastes solidification and material recovery: prospectives in Italy. Prospettive dell'applicazione delle tecniche di inertizzazione

    Energy Technology Data Exchange (ETDEWEB)

    De Angelis, G; Balzano, S

    1988-12-01

    This paper focuses on state-of-the-art materials recovery techniques employed in the solidification/stabilization of industrial wastes. Particular consideration is given to the Italian situation. After a review, with reference to waste/matrix compatibility inherent problems, of the presently employed main encapsulation techniques (with matrices based on cement, lime, clay, thermoplastic materials, organic polymers, macroencapsulating compounds), attention is addressed to solidification systems which allow a recovery of the waste material as low-technology by-products. Regarding the most important industrial waste streams: thermoplastic refuse, incinerator ashes, chemical sludges, the paper reviews efforts devoted not only to their chemical fixation in order to fulfill the current land disposal requirements, but mainly to their employment for production of manufactured articles.

  18. Method of heat decomposition for chemical decontaminating resin waste

    International Nuclear Information System (INIS)

    Kikuchi, Akira.

    1988-01-01

    Purpose: To make resin wastes into non-deleterious state, discharge them into a resin waste storage tank of existent radioactive waste processing facility and store and dispose them. Constitution: In the processing of chemical decontaminating resin wastes, iron exchange resins adsorbing chemical decontaminating agents comprising a solution of citric acid, oxalic acid, formic acid and EDTA alone or as a mixture of them are heated to dry, thermally decomposed and then separated from the ion exchange resins. That is, the main ingredients of the chemical decontaminating agents are heat-decomposed when heated and dried at about 250 deg C in air and converted into non-toxic gases such as CO, CO 2 , NO, NO 2 or H 2 O. Further, since combustion or carbonization of the basic materials for the resin is not caused at such a level of temperature, the resin wastes removed with organic acid and chelating agents are transferred to an existent resin waste storage tank and stored therein. In this way, facility cost and radiation exposure can remarkably be decreased. (Kamimura, M.)

  19. Chemical durability of soda-lime-aluminosilicate glass for radioactive waste vitrification

    International Nuclear Information System (INIS)

    Eppler, F.H.; Yim, M.S.

    1998-01-01

    Vitrification has been identified as one of the most viable waste treatment alternatives for nuclear waste disposal. Currently, the most popular glass compositions being selected for vitrification are the borosilicate family of glasses. Another popular type that has been around in glass industry is the soda-lime-silicate variety, which has often been characterized as the least durable and a poor candidate for radioactive waste vitrification. By replacing the boron constituent with a cheaper substitute, such as silica, the cost of vitrification processing can be reduced. At the same time, addition of network intermediates such as Al 2 O 3 to the glass composition increases the environmental durability of the glass. The objective of this study is to examine the ability of the soda-lime-aluminosilicate glass as an alternative vitrification tool for the disposal of radioactive waste and to investigate the sensitivity of product chemical durability to variations in composition

  20. Harmonization of industrial and oilfield waste management issues in Alberta

    International Nuclear Information System (INIS)

    Halla, S.

    1999-01-01

    There has been an ongoing discussion concerning the harmonization of waste management requirements within Alberta between the Alberta Energy and Utilities Board (EUB) and Alberta Environment (AENV), with the ultimate goal of publishing a memorandum of understanding (MOU) that will lay out the division of responsibilities between the two authorities on this matter. An overview is included of waste management in Alberta and of the harmonization agreements attained to date, with a stress on oil field waste issues. The EUB and AENV developed a MOE on the harmonization of waste management in Alberta, and a discussion is made of the concept of equivalency, which is used in the development of 'EUB guide 58: oilfield waste management requirements for the upstream petroleum industry' and will be a guiding principle for the MOU. Although the EUB's processes for waste management will not be exactly the same as AENV's, the EUB has made the commitment that, as a minimum, the requirements will provide the same level of environmental protection and public safety equivalent to that provided by AENV

  1. Conversion of industrial food wastes by Alcaligenes latus into polyhydroxyalkanoates.

    Science.gov (United States)

    Yu, P H; Chua, H; Huang, A L; Ho, K P

    1999-01-01

    Broader usage of biodegradable plastics in packaging and disposable products as a solution to environmental problems would heavily depend on further reduction of costs and the discovery of novel biodegradable plastics with improved properties. As the first step in our pursuit of eventual usage of industrial food wastewater as nutrients for microorganisms to synthesise environmental-friendly bioplastics, we investigated the usage of soya wastes from a soya milk dairy, and malt wastes from a beer brewery plant as the carbon sources for the production of polyhydroxyalkanoates (PHA) by selected strain of microorganism. Bench experiments showed that Alcaligenes latus DSM 1124 used the nutrients from malt and soya wastes to biosynthesise PHAs. The final dried cell mass and specific polymer production of A. latus DSM 1124 were 32g/L and 70% polymer/cells (g/g), 18.42 g/L and 32.57% polymer/cell (g/g), and 28 g/L and 36% polymer/cells (g/g), from malt waste, soya waste, and from sucrose, respectively. These results suggest that many types of food wastes might be used as the carbon source for the production of PHA.

  2. CORROSION AND CHEMICAL WASTE IN SAWBLADES STEEL USED IN WOOD

    Directory of Open Access Journals (Sweden)

    Paulo Fernando Trugilho

    2002-01-01

    Full Text Available The objective this work was to evaluate the chemical waste provoked by the wood on the sheets of steel used in the making of the mountains and cut tools. It was certain the correlationbetween the chemical waste and the extractive soluble in cold water, hot water and in the sequencetoluene and ethanol content. Two types of steel and twenty-seven species different from wood wereused. The corrosive agent, constituted of 50 g of fresh sawdust (moist mixed to 50 ml of distilledwater, it was prepared and placed inside of the plastic box, hermetically closed, on the samples ofsteel, which were totally immersed. The box was placed in a water bath pre-heated to 75°C, that themedium temperature of reaction is considered, that affects the sheet of the sawblade in operation. Thisgroup was operated to 80 rotations per minute (rpm. The time of reaction was of four hours. Afterthat time the corrosive agent was discarded and the samples were washed, dried and weighed. At theend, each sample was processed by a total period of forty hours. The chemical waste was evaluated by the weight difference suffered from beginning at the end of the experiment. For theresults it was observed that the Eucalyptus tradryphloia and the Eucalyptus phaeotricha the speciesthat provoked were, respectively, the largest and smaller chemical waste for the two types of steelappraised. Great variation exists in the chemical waste due to the effect of the species. The corrosionand chemical waste are especially related with the quality of the material solved in ethanol. The 1070steel were more attached than the 6170 steel.

  3. The Industrial Toxics Project: Targeting chemicals for environmental results

    International Nuclear Information System (INIS)

    Burch, W.M.

    1991-01-01

    In September, 1990, the Administrator of the US Environmental Protection Agency committed the Agency to a program of targeting chemicals for multi-media risk reduction activities through pollution prevention. The Industrial Toxics Project will place emphasis on obtaining voluntary commitments from industry to reduce releases of toxic chemicals to the air, water, and land with a goal of reducing releases nationwide by 33% by 1992 and 50% by 1995. An initial list of 18 chemicals have been selected based on recommendations from each Agency program. The chemicals selected are subject to reporting under the Toxic Chemical Release Inventory Program which will provide the basis for tracking progress. The chemicals are characterized by high production volume, toxicity and releases and present the potential for significant risk reduction through pollution prevention. This presentation will discuss the focus and direction of this new initiative

  4. Stability assessment of lycopene microemulsion prepared using tomato industrial waste against various processing conditions.

    Science.gov (United States)

    Amiri-Rigi, Atefeh; Abbasi, Soleiman

    2017-11-01

    Green separation techniques are growing at a greater rate than solvent extraction as a result of the constant consumer drive to 'go natural'. Considering the increasing evidence of the health benefits of lycopene and massive tomato industrial waste, in the present study, lycopene was extracted from tomato industrial waste using microemulsion technique and its mean droplet size and size distribution was determined. Moreover, the effects of pasteurization, sterilization, freeze-thaw cycles and ultraviolet (UV) irradiation on the thermodynamic stability, turbidity and lycopene concentration of the lycopene microemulsion were monitored. Freeze-thaw cycles, pasteurization and short exposure to UV irradiation showed no or negligible influence on lycopene content and turbidity of the microemulsion. However, long exposure to UV (260 min) reduced the lycopene content and turbidity by 34% and 10%, respectively. HHST (higher-heat shorter-time) and sterilization also reduced lycopene content (25%) and increased turbidity (32%). The lycopene microemulsion showed satisfactory stability over a process where its monodispersity and nanosize could be of potential advantage to the food and related industries. Regarding the carcinogenicity of synthetic colourants, potential applications of the lycopene microemulsion include in soft drinks and minced meat, which would result in a better colour and well-documented health-promoting qualities. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

  5. Biomethane potential of industrial paper wastes and investigation of the methanogenic communities involved.

    Science.gov (United States)

    Walter, Andreas; Silberberger, Sandra; Juárez, Marina Fernández-Delgado; Insam, Heribert; Franke-Whittle, Ingrid H

    2016-01-01

    Cellulose-containing waste products from the agricultural or industrial sector are potentially one of the largest sources of renewable energy on earth. In this study, the biomethane potential (BMP) of two types of industrial paper wastes, wood and pulp residues (WR and PR, respectively), were evaluated under both mesophilic and thermophilic conditions, and various pretreatment methods were applied in the attempt to increase the methane potential during anaerobic digestion. The methanogenic community composition was investigated with denaturing gradient gel electrophoresis (DGGE) and the ANAEROCHIP microarray, and dominant methanogens were quantitated using quantitative PCR. All pretreatments investigated in this study with the exception of the alkaline pretreatment of PR were found to increase the BMP of two paper industry wastes. However, the low recalcitrance level of the PR resulted in the pretreatments being less effective in increasing BMP when compared with those for WR. These results were supported by the physico-chemical data. A combined application of ultrasound and enzymatic pretreatment was found to be the best strategy for increasing methane yields. The retention time of substrates in the reactors strongly influenced the BMP of wastes subjected to the different pretreatments. In sludges from both paper wastes subjected to the various pretreatments, mixotrophic Methanosarcina species were found to dominate the community, accompanied by a consortium of hydrogenotrophic genera. Pretreating industrial paper wastes could be a potentially viable option for increasing the overall degradation efficiency and decreasing reactor retention time for the digestion of complex organic matter such as lignocellulose or hemicellulose. This would help reduce the environmental burden generated from paper production. Although there were minor differences in the methanogenic communities depending on the temperature of anaerobic digestion, there was little effect of substrate

  6. New facility for processing and storage of radioactive and toxic chemical waste

    International Nuclear Information System (INIS)

    Gallagher, F.E. III

    1976-01-01

    A new facility for the processing and storage of radioactive and toxic chemical waste is described. The facility is located in the science and engineering complex of the Santa Barbara campus of the University of California, near the Pacific Ocean. It is designed to provide a safe and secure processing and storage area for hazardous wastes, while meeting the high aesthetic standards and ecological requirements of campus and community regulatory boards. The ventilation system and fire prevention features will be described in detail. During the design phase, a small laboratory was added to provide an area for the radiation protection and industrial hygiene programs. Operational experience with this new facility is discussed

  7. Chemical Resistance of Ornamental Compound Stone Produced with Marble Waste and Unsaturated Polyester

    Science.gov (United States)

    Ribeiro, Carlos E. Gomes; Rodriguez, Rubén J. Sánchez; Vieira, Carlos M. Fontes

    Ornamental compound stone are produced by industry for decades, however, few published studies describe these materials. Brazil has many deposits of stone wastes and a big potential to produce these materials. This work aims to evaluate the chemical resistance of ornamental compound stones produced with marble waste and unsaturated polyester. An adaptation of Annex H of ABNT NBR 13818:97 standard, with reagents commonly used in household products, was used. The results were compared with those obtained for natural stone used in composite production.

  8. Waste dissolution with chemical reaction, diffusion and advection

    International Nuclear Information System (INIS)

    Chambre, P.L.; Kang, C.H.; Lee, W.W.L.; Pigford, T.H.

    1987-06-01

    This paper extends the mass-transfer analysis to include the effect of advective transport in predicting the steady-state dissolution rate, with a chemical-reaction-rate boundary condition at the surface of a waste form of arbitrary shape. This new theory provides an analytic means of predicting the ground-water velocities at which dissolution rate in a geologic environment will be governed entirely to the chemical reaction rate. As an illustration, we consider the steady-state potential flow of ground water in porous rock surrounding a spherical waste solid. 3 refs., 2 figs

  9. A process for treatment of mixed waste containing chemical plating wastes

    International Nuclear Information System (INIS)

    Anast, K.R.; Dziewinski, J.; Lussiez, G.

    1995-01-01

    The Waste Treatment and Minimization Group at Los Alamos National Laboratory has designed and will be constructing a transportable treatment system to treat low-level radioactive mixed waste generated during plating operations. The chemical and plating waste treatment system is composed of two modules with six submodules, which can be trucked to user sites to treat a wide variety of aqueous waste solutions. The process is designed to remove the hazardous components from the waste stream, generating chemically benign, disposable liquids and solids with low level radioactivity. The chemical and plating waste treatment system is designed as a multifunctional process capable of treating several different types of wastes. At this time, the unit has been the designated treatment process for these wastes: Destruction of free cyanide and metal-cyanide complexes from spent plating solutions; destruction of ammonia in solution from spent plating solutions; reduction of Cr VI to Cr III from spent plating solutions, precipitation, solids separation, and immobilization; heavy metal precipitation from spent plating solutions, solids separation, and immobilization, and acid or base neutralization from unspecified solutions

  10. Information processing to determine waste minimization/pollution prevention strategies in the petroleum industry

    Energy Technology Data Exchange (ETDEWEB)

    Falcon, Mariali F. de [CORPOVEN, S.A. (Venezuela)

    1993-12-31

    With the passage of the 1984 Hazardous and Solid Waste Amendments to the Resource Conservation and Recovery Act in the United States, industries, and particularly the petroleum industry, have become more interested in their waste management practices. This works aims to present a methodology to organize the collected data concerning waste minimization and, or, pollution prevention in the petroleum industry into a bibliographic database

  11. Information processing to determine waste minimization/pollution prevention strategies in the petroleum industry

    Energy Technology Data Exchange (ETDEWEB)

    Falcon, Mariali F. de [CORPOVEN, S.A. (Venezuela)

    1994-12-31

    With the passage of the 1984 Hazardous and Solid Waste Amendments to the Resource Conservation and Recovery Act in the United States, industries, and particularly the petroleum industry, have become more interested in their waste management practices. This works aims to present a methodology to organize the collected data concerning waste minimization and, or, pollution prevention in the petroleum industry into a bibliographic database

  12. Acute and Chronic Toxicity of Soluble Fractions of Industrial Solid Wastes on Daphnia magna and Vibrio fischeri

    Directory of Open Access Journals (Sweden)

    Letícia Flohr

    2012-01-01

    Full Text Available Industrial wastes may produce leachates that can contaminate the aquatic ecosystem. Toxicity testing in acute and chronic levels is essential to assess environmental risks from the soluble fractions of these wastes, since only chemical analysis may not be adequate to classify the hazard of an industrial waste. In this study, ten samples of solid wastes from textile, metal-mechanic, and pulp and paper industries were analyzed by acute and chronic toxicity tests with Daphnia magna and Vibrio fischeri. A metal-mechanic waste (sample MM3 induced the highest toxicity level to Daphnia magna(CE50,48 h=2.21%. A textile waste induced the highest toxicity level to Vibrio fischeri (sample TX2, CE50,30 min=12.08%. All samples of pulp and paper wastes, and a textile waste (sample TX2 induced chronic effects on reproduction, length, and longevity of Daphnia magna. These results could serve as an alert about the environmental risks of an inadequate waste classification method.

  13. Immobilization technologies for the management of hazardous industrial waste using granite waste (case study)

    Energy Technology Data Exchange (ETDEWEB)

    Lasheen, Mohamed R.; Ashmawy, Azza M.; Ibrahim, Hanan S.; Moniem, Shimaa M. Abdel [National Research Centre, Giza (Egypt)

    2016-03-15

    Full characterization of granite waste sludge (GWS) was accomplished by X-ray diffraction (XRD) and Xray fluorescence (XRF) for identification of its phase and chemical composition. Different leaching tests were conducted to determine the efficiency of the GWS for metal stabilization in hazardous sludge. The leaching of the metals from stabilized contaminated sludge was decreased as the GWS amount increased. Only 15% of GWS was sufficient for stabilization of all metal ions under investigation. The main reason for metal immobilization was attributed to the aluminosilicates or silicates matrix within the GWS, which can transform the metals in the form of their insoluble hydroxides or absorbed in the stabilized matrix. Also, solidification/stabilization technique was used for remediation of contaminated sludge. Compressive strength test after curing for 28 days was used for measuring the effectiveness of remediation technique; it was found to be 1.88MPa. This indicated that the remediated sludge was well solidified and safe to be used as a raw substance for roadway blocks. Therefore, this huge amount of by-product sludge derived from the granite cutting industry, which has a negative environmental impact due to its disposal, can be utilized as a binder material for solidification/stabilization of hazardous sludge.

  14. Advances in chemical engineering in nuclear and process industries

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-06-01

    Symposium on Advances in Chemical Engineering in Nuclear and Process Industries dealt with a wide spectrum of areas encompassing various industries such as nuclear, fertilizer, petrochemical, refinery and cement. The topics covered in the symposium dealt with the advancements in the existing fields of science and technologies as well as in some of the emerging technologies such as membrane technology, bio-chemical and photo-chemical engineering etc. with a special emphasis on nuclear related aspects. Papers relevant to INIS are indexed separately.

  15. Advances in chemical engineering in nuclear and process industries

    International Nuclear Information System (INIS)

    1994-06-01

    Symposium on Advances in Chemical Engineering in Nuclear and Process Industries dealt with a wide spectrum of areas encompassing various industries such as nuclear, fertilizer, petrochemical, refinery and cement. The topics covered in the symposium dealt with the advancements in the existing fields of science and technologies as well as in some of the emerging technologies such as membrane technology, bio-chemical and photo-chemical engineering etc. with a special emphasis on nuclear related aspects. Papers relevant to INIS are indexed separately

  16. Risk management programs in the chemical industry from Bhopal onward

    International Nuclear Information System (INIS)

    Cramer, J.J.; Greenberg, H.R.

    1992-01-01

    Chemical process safety has long been a consideration in industry but the tragedy at Bhopal in late 1984 resulted in significantly increased attention from industry, government, and the public. Whereas Bhopal had a major effect on regulations in the US, two earlier, highly publicized accidents affected regulations in the United Kingdom and Europe. A 1974 cyclohexane explosion at a chemical manufacturing plant in Flixborough, England, caused a number of fatalities, while a 1976 runaway reaction at a chemical works near Sevesco, Italy, contaminated surrounding farmland and water supplies with dioxin. Although the public's interest can be fickle, the residual concern from all these incidents has been sufficient to affect important regulatory and industry initiatives in the US and abroad. The development of the most important of the US initiatives are reviewed here. Common elements in various process safety management programs are noted and the latest regulatory developments reported. Application can be made to the nuclear industry

  17. Environmental impact of industrial sludge stabilization/solidification products: chemical or ecotoxicological hazard evaluation?

    Science.gov (United States)

    Silva, Marcos A R; Testolin, Renan C; Godinho-Castro, Alcione P; Corrêa, Albertina X R; Radetski, Claudemir M

    2011-09-15

    Nowadays, the classification of industrial solid wastes is not based on risk analysis, thus the aim of this study was to compare the toxicity classifications based on the chemical and ecotoxicological characterization of four industrial sludges submitted to a two-step stabilization/solidification (S/S) processes. To classify S/S products as hazardous or non-hazardous, values cited in Brazilian chemical waste regulations were adopted and compared to the results obtained with a battery of biotests (bacteria, alga and daphnids) which were carried out with soluble and leaching fractions. In some cases the hazardous potential of industrial sludge was underestimated, since the S/S products obtained from the metal-mechanics and automotive sludges were chemically classified as non-hazardous (but non-inert) when the ecotoxicity tests showed toxicity values for leaching and soluble fractions. In other cases, the environmental impact was overestimated, since the S/S products of the textile sludges were chemically classified as non-inert (but non-hazardous) while ecotoxicity tests did not reveal any effects on bacteria, daphnids and algae. From the results of the chemical and ecotoxicological analyses we concluded that: (i) current regulations related to solid waste classification based on leachability and solubility tests do not ensure reliable results with respect to environmental protection; (ii) the two-step process was very effective in terms of metal immobilization, even at higher metal-concentrations. Considering that S/S products will be subject to environmental conditions, it is of great interest to test the ecotoxicity potential of the contaminants release from these products with a view to avoiding environmental impact given the unreliability of ecotoxicological estimations originating from chemical analysis. Copyright © 2011 Elsevier B.V. All rights reserved.

  18. News from Online: Industrial Chemicals and Polymers

    Science.gov (United States)

    Sweeney Judd, Carolyn

    1999-02-01

    of the American Chemical Society Divisions of Polymer Chemistry and Polymeric Materials: Science and Engineering and General Electric Corporation. The POLYED site, http:/ /chemdept.uwsp.edu/polyed/index.htm, is hosted by the University of Wisconsin at Stevens Point. This National Center for Polymer Education is another good place to go for information. More education is available at the Ziegler Research Group Home Page at http://www.chem.ucalgary.ca/groups/ziegler/index.html . Go to Metallocene as Olefin Polymerization Catalysis: An Introduction ( http://www.chem.ucalgary.ca/groups/ziegler/met_intro.html ) for historical accounts of metallocene and Ziegler-Natta catalysts. Movies are available here too. This Canadian site is well-documented and educational. Back at the University of Wisconsin-Madison, The Why Files site at http://whyfiles.news.wisc.edu helps bring important chemical and technology news to the public. Go to the archived files of October 1997 ( http://whyfiles.news.wisc.edu/shorties/catalyst.html ) to find information about the importance of low-temperature metallocene catalysts. The Why Files received funding from the National Science Foundation. Go here for science information in an easy-to-read format. One of the driving forces toward better catalysis is the attempt to reach 100% product, combining efficiency with lowered pollution. Companies can look to the Environmental Protection Agency for information: Environsense at http://es.epa.gov/ is pledged to offer "Common Sense Solutions to Environmental Problems". So where can we get these polymers? The American Chemical Society can help. Go to Chemcylopedia at http://pubs.acs.org/chemcy99/ for great information. Both purchasers and users of chemicals can benefit from this site. Searches can be made on the chemical or on the supplier. Information provided includes CAS Registry Numbers and special shipping requirements as well as potential applications. Do you remember that we started with paper? Let

  19. Chemical Decontamination of Metallic Waste from Uranium Conversion Plant Dismantling

    International Nuclear Information System (INIS)

    Hwang, D. S.; Choi, Y. D.; Hwang, S. T.; Park, J. H.; Byun, J. I.; Jang, N. S.

    2005-01-01

    Korea Atomic Energy Research Institute (KAERI) started a decommissioning program of the uranium conversion plant. Pre-work was carried as follows; installation of the access control facility, installation of a changing room and shower room, designation of an emergency exit way and indicating signs, installation of a radiation management facility, preparation of a storage area for tools and equipments, inspection and load test of crane, distribution and packaging of existing waste, and pre-decontamination of the equipment surface and the interior. First, decommissioning work was performed in kiln room, which will be used for temporary radioactive waste storage room. Kiln room housed hydro fluorination rotary kiln for production of uranium tetra-fluoride. The kiln is about 0.8 m in diameter and 5.5 m long. The total dismantled waste was 6,690 kg, 73 % of which was metallic waste and 27 % the others such as cable, asbestos, concrete, secondary waste, etc. And effluent treatment room and filtration room were dismantled for installation of decontamination equipment and lagoon sludge treatment equipment. There were tanks and square mixer in these rooms. The total dismantled waste was 17,250 kg, 67% of which was metallic waste and 33% the others. These dismantled metallic wastes consist of stainless and carbon steel. In this paper, the stainless steel plate and pipe were decontaminated by the chemical decontamination with ultrasonic

  20. Valorization of titanium metal wastes as tanning agent used in leather industry

    International Nuclear Information System (INIS)

    Crudu, Marian; Deselnicu, Viorica; Deselnicu, Dana Corina; Albu, Luminita

    2014-01-01

    Highlights: • Valorization of titanium wastes which cannot be recycled in metallurgical industry. • Transferring Ti waste into raw materials for obtaining Ti based tanning agent. • Characterization of new Ti based tanning agents and leather tanned with them. • Characterization of sewage waste water and sludge resulted from leather manufacture. • Analysis of the impact of main metal component of Ti waste. - Abstract: The development of new tanning agents and new technologies in the leather sector is required to cope with the increasingly higher environmental pressure on the current tanning materials and processes such as tanning with chromium salts. In this paper, the use of titanium wastes (cuttings) resulting from the process of obtaining highly pure titanium (ingots), for the synthesis of new tanning agent and tanning bovine hides with new tanning agent, as alternative to tanning with chromium salts are investigated. For this purpose, Ti waste and Ti-based tanning agent were characterized for metal content by inductively coupled plasma mass spectrometry (ICP-MS) and chemical analysis; the tanned leather (wet white leather) was characterized by Scanning Electron Microscope/Energy Dispersive Using X-ray (Analysis). SEM/EDX analysis for metal content; Differential scanning calorimetric (DSC), Micro-Hot-Table and standard shrinkage temperature showing a hydrothermal stability (ranged from 75.3 to 77 °C) and chemical analysis showing the leather is tanned and can be processed through the subsequent mechanical operations (splitting, shaving). On the other hand, an analysis of major minor trace substances from Ti-end waste (especially vanadium content) in new tanning agent and wet white leather (not detected) and residue stream was performed and showed that leachability of vanadium is acceptable. The results obtained show that new tanning agent obtained from Ti end waste can be used for tanning bovine hides, as eco-friendly alternative for chrome tanning

  1. Valorization of titanium metal wastes as tanning agent used in leather industry

    Energy Technology Data Exchange (ETDEWEB)

    Crudu, Marian, E-mail: mariancrudu@yahoo.com [The National Research and Development Institute for Textiles and Leather – Division Leather and Footwear Research Institute, 93 Ion Minulescu Str., Bucharest (Romania); Deselnicu, Viorica, E-mail: viorica.deselnicu@icpi.ro [The National Research and Development Institute for Textiles and Leather – Division Leather and Footwear Research Institute, 93 Ion Minulescu Str., Bucharest (Romania); Deselnicu, Dana Corina, E-mail: d_deselnicu@yahoo.com [University Politehnica Bucharest, Splaiul Independentei Nr. 313, Sector 6, RO-060042 Bucharest (Romania); Albu, Luminita, E-mail: luminita.albu@gmail.com [The National Research and Development Institute for Textiles and Leather – Division Leather and Footwear Research Institute, 93 Ion Minulescu Str., Bucharest (Romania)

    2014-10-15

    Highlights: • Valorization of titanium wastes which cannot be recycled in metallurgical industry. • Transferring Ti waste into raw materials for obtaining Ti based tanning agent. • Characterization of new Ti based tanning agents and leather tanned with them. • Characterization of sewage waste water and sludge resulted from leather manufacture. • Analysis of the impact of main metal component of Ti waste. - Abstract: The development of new tanning agents and new technologies in the leather sector is required to cope with the increasingly higher environmental pressure on the current tanning materials and processes such as tanning with chromium salts. In this paper, the use of titanium wastes (cuttings) resulting from the process of obtaining highly pure titanium (ingots), for the synthesis of new tanning agent and tanning bovine hides with new tanning agent, as alternative to tanning with chromium salts are investigated. For this purpose, Ti waste and Ti-based tanning agent were characterized for metal content by inductively coupled plasma mass spectrometry (ICP-MS) and chemical analysis; the tanned leather (wet white leather) was characterized by Scanning Electron Microscope/Energy Dispersive Using X-ray (Analysis). SEM/EDX analysis for metal content; Differential scanning calorimetric (DSC), Micro-Hot-Table and standard shrinkage temperature showing a hydrothermal stability (ranged from 75.3 to 77 °C) and chemical analysis showing the leather is tanned and can be processed through the subsequent mechanical operations (splitting, shaving). On the other hand, an analysis of major minor trace substances from Ti-end waste (especially vanadium content) in new tanning agent and wet white leather (not detected) and residue stream was performed and showed that leachability of vanadium is acceptable. The results obtained show that new tanning agent obtained from Ti end waste can be used for tanning bovine hides, as eco-friendly alternative for chrome tanning.

  2. Poly β-Hydroxybutyrate Production by Bacillus subtilis NG220 Using Sugar Industry Waste Water

    Science.gov (United States)

    Singh, Gulab; Kumari, Anish; Mittal, Arpana; Yadav, Anita; Aggarwal, Neeraj K.

    2013-01-01

    The production of poly β-hydroxybutyrate (PHB) by Bacillus subtilis NG220 was observed utilizing the sugar industry waste water supplemented with various carbon and nitrogen sources. At a growth rate of 0.14 g h−1 L−1, using sugar industry waste water was supplemented with maltose (1% w/v) and ammonium sulphate (1% w/v); the isolate produced 5.297 g/L of poly β-hydroxybutyrate accumulating 51.8% (w/w) of biomass. The chemical nature of the polymer was confirmed with nuclear magnetic resonance, Fourier transform infrared, and GC-MS spectroscopy whereas thermal properties were monitored with differential scanning calorimetry. In biodegradability study, when PHB film of the polymer (made by traditional solvent casting technique) was subjected to degradation in various natural habitats like soil, compost, and industrial sludge, it was completely degraded after 30 days in the compost having 25% (w/w) moisture. So, the present study gives insight into dual benefits of conversion of a waste material into value added product, PHB, and waste management. PMID:24027767

  3. Thermal energy storage for industrial waste heat recovery

    Science.gov (United States)

    Hoffman, H. W.; Kedl, R. J.; Duscha, R. A.

    1978-01-01

    The potential is examined for waste heat recovery and reuse through thermal energy storage in five specific industrial categories: (1) primary aluminum, (2) cement, (3) food processing, (4) paper and pulp, and (5) iron and steel. Preliminary results from Phase 1 feasibility studies suggest energy savings through fossil fuel displacement approaching 0.1 quad/yr in the 1985 period. Early implementation of recovery technologies with minimal development appears likely in the food processing and paper and pulp industries; development of the other three categories, though equally desirable, will probably require a greater investment in time and dollars.

  4. Selection and Evaluation of Chemical Indicators for Waste Stream Identification

    Science.gov (United States)

    DeVita, W. M.; Hall, J.

    2015-12-01

    Human and animal wastes pose a threat to the quality of groundwater, surface water and drinking water. This is especially of concern for private and public water supplies in agricultural areas of Wisconsin where land spreading of livestock waste occurs on thin soils overlaying fractured bedrock. Current microbial source tracking (MST) methods for source identification requires the use of polymerase chain reaction (PCR) techniques. Due to cost, these tests are often not an option for homeowners, municipalities or state agencies with limited resources. The Water and Environmental Analysis Laboratory sought to develop chemical methods to provide lower cost processes to determine sources of fecal waste using fecal sterols, pharmaceuticals (human and veterinary) and human care/use products in ground and surface waters using solid phase extraction combined with triple quadrupole mass spectrometry. The two separate techniques allow for the detection of fecal sterol and other chemical markers in the sub part per billion-range. Fecal sterol ratios from published sources were used to evaluate drinking water samples and wastewater from onsite waste treatment systems and municipal wastewater treatment plants. Pharmaceuticals and personal care products indicative of human waste included: acetaminophen, caffeine, carbamazepine, cotinine, paraxanthine, sulfamethoxazole, and the artificial sweeteners; acesulfame, saccharin, and sucralose. The bovine antibiotic sulfamethazine was also targeted. Well water samples with suspected fecal contamination were analyzed for fecal sterols and PPCPs. Results were compared to traditional MST results from the Wisconsin State Laboratory of Hygiene. Chemical indicators were found in 6 of 11 drinking water samples, and 5 of 11 were in support of MST results. Lack of detection of chemical indicators in samples contaminated with fecal waste supports the need for confirmatory methods and advancement of chemical indicator detection technologies.

  5. Market forces in municipal and industrial waste-to-energy

    International Nuclear Information System (INIS)

    Makansi, J.

    1991-01-01

    The market for municipal and industrial waste-to-energy can be characterized simply as currently soft with continued excellent long-term prospects. But as in all markets large and small, niche opportunities exist now which can be profitable with proper definition and strategy. Economics of several projects have proven marginal, cost overruns are common, and revenue projections are sometimes overstates. Also contributing to poorer economics of late are lower prices for the electric power produced from these plants. New environmental restrictions are adding 10-15% to the capital costs of a given project. On the industrial front, the strength of waste-fuel firing continues to be evident for independent power production. Important fuel-niche markets have sprung up over the last decade including petroleum coke, coal-mining wastes, hospital or redbag wastes, biomass, used tires, and so on. Another fuel niche is hazardous waste incineration. In the municipal arena, realism has not yet hit the recycling and source reduction enthusiasts. Only 25-35% recycling is considered practical by experts. There are also limits to how often material can be recycled. Finally, in spite of the best efforts of the population to control the amount of refuse generated and to recycle that which is, population and economic growth may overtake any new sense of environmental responsibility. And, yes, the additional refuse still has to go somewhere exclamation point The best somewhere option continues to be a waste-to-energy plant. Current market opportunities and two other market forces (international activities and the role of US utilities) are discussed

  6. The Asia/Pacific chemical industry

    International Nuclear Information System (INIS)

    Tattum, L.

    1993-01-01

    The year of the Rooster may herald interesting change for the Asia/Pacific region. Local dynamics are shifting away from Japan, the traditional motor of the region, now in recession toward China, which is increasingly catching the imagination of investors. Japan's lead in major petrochemicals has eroded since restructuring of domestic industry. Ten years ago Japan was the location for 76% of Asian ethylene capacity, according to Chem Systems. It also held 89% of styrene capacity, 69% of polyolefins, and 62% of polyvinyl chloride (PVC). Today it accounts for only 46% of Asian ethylene, 53% of styrene, 40% of polyolefin, and 37% of PVC capacity. Another country to watch is Vietnam many companies are waiting for sanctions to lift on US investment. When they do, this country of rich oil reserves but per capita income of only $200, will look to petrochemicals as a source of foreign investment

  7. Public perceptions of industrial risks: the context of public attitudes toward radioactive waste

    International Nuclear Information System (INIS)

    Earle, T.C.

    1981-06-01

    A survey was made to determine the public risk perception of several industrial hazards. A free response approach was used in order for respondents to generate their own alternatives. The general class of hazard investigated here included all hazardous industrial facilities. The free response survey was used to study public perception of: (a) the closeness of the nearest hazardous industrial facility (as estimated by the respondent); (b) the sort of facility it is; (c) the sorts of risk associated with it; and (d) the persons placed at risk by it. Respondents also identified the risks of, and the persons placed at risk by, both a toxic chemical disposal facility and a nuclear waste disposal facility. Results of this study thus can inform us of the unprompted concerns of the public regarding a wide variety of industrial facilities

  8. Cogeneration from poultry industry wastes: Indirectly fired gas turbine application

    International Nuclear Information System (INIS)

    Bianchi, M.; Cherubini, F.; De Pascale, A.; Peretto, A.; Elmegaard, B.

    2006-01-01

    The availability of wet biomass as waste from a lot of industrial processes, from agriculture and farms and the need to meet the environmental standards force to investigate all options in order to dispose this waste. The possible treatments usually strongly depend on biomass characteristics, namely water content, density, organic content, heating value, etc. In particular, some of these wastes can be burnt in special plants, using them as energy supply for different processes. The study carried out with this paper is concerned with the promising utilization of the organic wastes from an existing poultry industry as fuel. Different plant configurations have been considered in order to make use of the oil and of the meat and bone meal, which are the by-products of the chicken cooking process. In particular, the process plant can be integrated with an energy supply plant, which can consist of an indirectly fired gas turbine. Moreover, a steam turbine plant or a simplified system for the supply of the only technological steam are investigated and compared. Thermodynamic and economic analysis have been carried out for the examined configurations in order to outline the basic differences in terms of energy savings/production and of return of the investments

  9. Strain selection and medium optimization for glucoamylase production from industrial potato waste by Aspergillus niger.

    Science.gov (United States)

    Izmirlioglu, Gulten; Demirci, Ali

    2016-06-01

    Glucoamylase is one of the most common enzymes used in the food industry to break down starch into its monomers. Glucoamylase production and its activity are highly dependent on medium composition. Starch is well known as a glucoamylase inducer, and utilization of industrial starchy potato waste is an inexpensive way of improving glucoamylase production. Since glucoamylase production is highly dependent on medium composition, in this study medium optimization for glucoamylase production was considered to enhance glucoamylase activity. Among the evaluated microbial species, Aspergillus niger van Tieghem was found to be the best glucoamylase-producing fungus. The Plackett-Burman design was used to screen various medium ingredients, and malt extract, FeSO4 .7H2 O and CaCl2 ·2H2 O were found to have significant effects on glucoamylase production. Finally, malt extract, FeSO4 .7H2 O and CaCl2 .2H2 O were optimized by using a central composite design of response surface methodology. The results showed that the optimal medium composition for A. niger van Tieghem was 50 g L(-1) industrial waste potato mash supplemented with 51.82 g L(-1) malt extract, 9.27 g L(-1) CaCl2 ·2H2 O and 0.50 g L(-1) FeSO4 .7H2 O. At the end of optimization, glucoamylase activity and glucose production were improved 126% and 98% compared to only industrial waste potato mash basal medium; 274.4 U mL(-1) glucoamylase activity and 41.7 g L(-1) glucose levels were achieved, respectively. © 2015 Society of Chemical Industry. © 2015 Society of Chemical Industry.

  10. Hot particles in industrial waste and mining tailings

    CERN Document Server

    Selchau-Hansen, K; Freyer, K; Treutler, C; Enge, W

    1999-01-01

    Industrial waste was studied concerning its radioactive pollution. Using known properties of the solid state nuclear track detector CR-39 we found among a high concentration of more or less homogeneously distributed single alpha-tracks discrete spots of very high enrichments of alpha-particles created by so called hot particles. We will report about the alpha-activity, the concentration of hot particles and about their ability to be air borne.

  11. Gasification of waste from furniture industries for generation of sustainable energy

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, J.L.; Silva, J.N.; Pereira, E.G.; Machado, C.S.; Da Conceicao, M.; Bezerra, T. [Federal Univ. of Vicosa, Minas Gerais State (Brazil)

    2010-07-01

    The global interest in renewable energy is attributed to the decline in fossil fuel sources and the need for technical, economic, social and environmental sustainability. This study focused on the new techniques that have been developed for the use of biomass for energy from wood wastes from the forest-based industry. As an energy source, wood waste contributes positively to the environment by reducing environmental problems related to contamination of soil, air and water through improper disposal of waste. Biomass gasification has the advantage of converting biomass into a combustible gas that can be used for heat generation, electricity and synthesis of chemicals. Syngas produced from gasification of eucalyptus residues has significant potential, with an average High Heating Value of 6.60 MJ/m{sup 3}, and regular composition during the process, with predominance of carbon monoxide, followed by hydrogen, carbon dioxide and methane.

  12. Utilization of oleo-chemical industry by-products for biosurfactant production

    Science.gov (United States)

    2013-01-01

    Biosurfactants are the surface active compounds produced by micro-organisms. The eco-friendly and biodegradable nature of biosurfactants makes their usage more advantageous over chemical surfactants. Biosurfactants encompass the properties of dropping surface tension, stabilizing emulsions, promoting foaming and are usually non- toxic and biodegradable. Biosurfactants offer advantages over their synthetic counterparts in many applications ranging from environmental, food, and biomedical, cosmetic and pharmaceutical industries. The important environmental applications of biosurfactants include bioremediation and dispersion of oil spills, enhanced oil recovery and transfer of crude oil. The emphasis of present review shall be with reference to the commercial production, current developments and future perspectives of a variety of approaches of biosurfactant production from the micro-organisms isolated from various oil- contaminated sites and from the by-products of oleo-chemical industry wastes/ by-products viz. used edible oil, industrial residues, acid oil, deodorizer distillate, soap-stock etc. PMID:24262384

  13. Radioactive and hazardous chemical wastes. Impact on man and his environment

    International Nuclear Information System (INIS)

    Parker, F.L.; Suess, M.J.

    1984-01-01

    The main objective of the various safety measures in all fields of human activities is to prevent deleterious effects of various agents on human health. Preventive health and safety measures therefore play an important role in achieving the main goal of the World Health Organization (WHO): 'Health for all by the year 2000'. The present WHO programme on environmental health emphasizes the prevention of chemical hazards as one of the most important environmental factors affecting human health. At the same time, protection from physical factors, including radiological protection, is part of this programme. Therefore, WHO compares health detriments from both physical and chemical agents. The paper describes the hazardous waste problems of great concern in industrialized countries. For instance, the Commission of the European Communities countries produce about 2x10 9 tonnes of waste per year, a rate which grows by 2 to 3% annually. This poses serious problems of pollution, particularly where the toxic ingredients do not decay. Special attention will also be given to the safe handling of high-level radioactive waste from the peaceful use of nuclear technology. These wastes have to be stored in safe storage facilities, or be disposed of without causing damage to man and his environment. The international measures to contain and control these wastes are described, including the activities of WHO within the Global Environmental Monitoring System and Regional Sea programmes of the United Nations Environment Programme. Guidelines and methodologies for the management of hazardous chemical and radioactive wastes are being developed through WHO to assist national authorities in this task. The paper pays special attention to a comparative assessment of environmental and public health impacts of toxic chemical and radioactive wastes. (author)

  14. Chemical recycling of mixed waste plastics by selective pyrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Tatsumoto, K.; Meglen, R.; Evans, R. [National Renewable Energy Laboratory, Golden, CO (United States)

    1995-05-01

    The goal of this work is to use selective pyrolysis to produce high-value chemicals from waste plastics mixtures. Selectivity is achieved by exploiting differences in reaction rates, catalysis, and coreactants. Target wastes are molecular mixtures such as; blends or composites, or mixtures from manufactured products such as; carpets and post-consumer mixed-plastic wastes. The experimental approach has been to use small-scale experiments using molecular beam mass spectrometry (MBMS), which provides rapid analysis of reaction products and permits rapid screening of process parameters. Rapid screening experiments permit exploration of many potential waste stream applications for the selective pyrolysis process. After initial screening, small-scale, fixed-bed and fluidized-bed reactors are used to provide products for conventional chemical analysis, to determine material balances, and to test the concept under conditions that will be used at a larger scale. Computer assisted data interpretation and intelligent chemical processing are used to extract process-relevant information from these experiments. An important element of this project employs technoeconomic assessments and market analyses of durables, the availability of other wastes, and end-product uses to identify target applications that have the potential for economic success.

  15. Protein recovery from dairy industry wastes with aerobic biofiltration

    Energy Technology Data Exchange (ETDEWEB)

    Wheatley, A D; Mitra, R I; Hawkes, H A

    1982-01-01

    Experiments were carried out to improve the economics of effluent treatment by the recovery of single cell protein. Field observations showed that acidic strong wastes, such as those from the dairy industry, produced a predominantly fungal biomass. Mixtures of dairy waste and domestic sewage did not produce fungal films. The most common fungi isolated were Fusarium and Geotrichum, but the species was affected by local conditions, i.e. creamery, yoghurt, milk or cheese wastes and the load to the plant. Batch culture was used to determine the growth requirements of Fusarium and Geotrichum and continuous culture, on vertical and horizontal fixed films, to determine growth and sloughing at different organic loads. The fungi grew well on acidic strong wastes which would discourage other organisms. A 1 cubic metre/hour pilot plant was built to treat the wastes from cheese, butter and cream production. The plant was run at pH 4-5 and at between 5 and 10 kg of BOD/day/cubic metres. BOD removal was between 30 and 50% and biomass production between 0.1 and 0.5 kg of dry solids/day. The filamentous fungal growth was separated from the tower effluent by an inclined screen. The amino acid content of the product was similar to other single-cell protein. Feeding trials are being carried out. (Refs. 14).

  16. High rate composting of herbal pharmaceutical industry solid waste.

    Science.gov (United States)

    Ali, M; Duba, K S; Kalamdhad, A S; Bhatia, A; Khursheed, A; Kazmi, A A; Ahmed, N

    2012-01-01

    High rate composting studies of hard to degrade herbal wastes were conducted in a 3.5 m(3) capacity rotary drum composter. Studies were spread out in four trials: In trial 1 and 2, one and two turns per day rotation was observed, respectively, by mixing of herbal industry waste with cattle (buffalo) manure at a ratio of 3:1 on wet weight basis. In trial 3 inocula was added in raw waste to enhance the degradation and in trial 4 composting of a mixture of vegetable market waste and herbal waste was conducted at one turn per day. Results demonstrated that the operation of the rotary drum at one turn a day (trial 1) could provide the most conducive composting conditions and co-composting (trial 4) gave better quality compost in terms of temperature, moisture, nitrogen, and Solvita maturity index. In addition a FT-IR study also revealed that trial 1 and trial 4 gave quality compost in terms of stability and maturity due to the presence of more intense peaks in the aromatic region and less intense peaks were found in the aliphatic region compared with trial 2 and trial 3.

  17. Natural radiation, nuclear wastes and chemical pollutants

    International Nuclear Information System (INIS)

    Christensen, T.; Ehdwall, H.; Stranden, E.

    1990-01-01

    Doses from natural radiation to the population in the Nordic Countries are summarized and man made modifications of the natural radiation environment are discussed. An account is given of the radiological consequences of energy conservation by reduced ventilation. Risks from possible future releases of radioactivity from final repositories of spent nuclear fuel are compared to the risks from present natural radioactivity in the environment. The possibilities for comparison between chemical and radiological risks are discussed. (author) 13 refs

  18. Second-generation bioethanol from industrial wood waste of South American species

    Directory of Open Access Journals (Sweden)

    María E. Vallejos

    2017-09-01

    Full Text Available There is a global interest in replacing fossil fuels with renewable sources of energy. The present review evaluates the significance of South-American wood industrial wastes for bioethanol production. Four countries have been chosen for this review, i.e., Argentina, Brazil, Chile, and Uruguay, based on their current or potential forestry industry. It should be noted that although Brazil has a global bioethanol market share of 25%, its production is mainly first-generation bioethanol from sugarcane. The situation in the other countries is even worse, in spite of the fact that they have regulatory frameworks in place already allowing the substitution of a percentage of gasoline by ethanol. Pines and eucalyptus are the usually forested plants in these countries, and their industrial wastes, as chips and sawdust, could serve as promising raw materials to produce second-generation bioethanol in the context of a forest biorefinery. The process to convert woody biomass involves three stages: pretreatment, enzymatic saccharification, and fermentation. The operational conditions of the pretreatment method used are generally defined according to the physical and chemical characteristics of the raw materials and subsequently determine the characteristics of the treated substrates. This article also reviews and discusses the available pretreatment technologies for eucalyptus and pines applicable to South-American industrial wood wastes, their enzymatic hydrolysis yields, and the feasibility of implementing such processes in the mentioned countries in the frame of a biorefinery.

  19. Recovery of uranium and accompanying metals from various types of industrial wastes

    International Nuclear Information System (INIS)

    Chajduk, E.; Danko, B.; Gajda, D.; Zakrzewska, G.; Harasimowicz, M.; Bieluszka, P.

    2014-01-01

    On January 28"t"h 2014 the Program of Polish Nuclear Energy was signed by Polish Government. According to this program Poland has to secure a constant supply of uranium for Polish NPPs in the future. Uranium in Poland occurs in Vistula Spit area in sandstone rocks and Podlasie Depression area in black dictyonema shales, which are low grade ores. Scarce uranium resources stimulate interest in its recovery from secondary resources as potential raw materials. Industrial wastes and by-products were considered as a source of uranium in this studies. Apart from uranium other valuable metals (e.g. vanadium, molybdenum or lanthanides) were recovered to improve the economy of the process. Three types of industrial wastes were examined: flotation tailings from the copper industry, phosphoric acid from the fertilizer industry and fracturing fluid from shale gas exploitation. Metals from flotation tailings were separated in two steps: 1) acidic leaching of the flotation waste using sulfuric acid solution and 2) separation of metals by ion-exchange chromatography. All the liquid samples were analyzed by ICP-MS method to determine the separation efficiency of the process. Uranium was recovered from phosphoric acid by high-pressure membrane filtration or by extraction/stripping integrated processes applying membrane modules Liquid-Cel® Extra-Flow (Celgard). Aqueous solutions after hydraulic fracturing are very diverse in terms of chemical composition, depending on borehole and fracturing technology applied. The content of various substances in backflow fluid depends on mechanical behavior and chemical composition of shale. Organic matter content in this type of waste did not exceed 1% usually, but the salinity is high. Initially, organic pollutants were removed and next the fluid was purified by combined various ion-exchangers. Individual metals were selectively eluted from ion-exchanger by combination of different eluents. The content of metals in samples was analyzed by ICP

  20. Chemical hazards from decontamination solutions in low level waste

    International Nuclear Information System (INIS)

    Leventhal, L.; Miller, A.; Turney, J.; Naughton, M.; IMPELL Corp., Walnut Creek, CA; Electric Power Research Inst., Palo Alto, CA)

    1985-01-01

    Recent regulations are focussing more attention on the non-radioactive matrix materials associated with radioactive wastes. Decontamination of operating facilities is becoming a more significant source of low-level waste. This study reviewed the chemical and biological hazards of over 50 decontamination processes. Seventeen of the most prominent hard and soft decontamination processes were examined in detail. The chemical and biological hazards of these seventeen are presented in this paper. These hazards influence the choice of radwaste processing and packaging operations and methods. Federal, state and local regulations further impact on operations and waste disposal. Hazards to personnel, in plant and off-site, resulting from the decontamination cycle are evaluated. 1 fig., 5 tabs

  1. What to do with your chemical waste ?

    CERN Multimedia

    Roland Magnier/SC

    2004-01-01

    For any type and quantity of chemical waste, please contact phone number 16 0879 or 16 3315 for the collection and safe elimination. The quality and the safety of our environment is our own responsibility. Let's do it. Roland Magnier/SC-GS

  2. Occupational chemical exposures in artificial organic fiber industries

    Energy Technology Data Exchange (ETDEWEB)

    Guirguis, S S; Cohen, M B

    1984-05-01

    This review discusses artificial organic fibers that are produced from materials of natural origin such as rayons, cellulose triacetates and proteins; or made from polymerised chemicals such as polyamides, polyesters, polyvinyls, modacrylics, carbon fibers, polyolefins, polyurethane and polytetrafluoroethylene. Chemicals involved include monomers, solvents, flame retardants, pigments and other additives. Occupational exposure to chemicals in the production stages are discussed and also the potential health hazards involved are reviewed. Current exposure levels, engineering controls and work practices for some of the chemicals used in the Ontario artificial fiber industry are discussed. Recommendations are made for areas that need further study and/or investigation.

  3. Experiment of Industrial Waste Absorption using Activated Carbon from Coal of Tanjung Tabalong, South Kalimantan

    Directory of Open Access Journals (Sweden)

    M. Ulum Gani

    2014-06-01

    Full Text Available DOI: 10.17014/ijog.v6i4.130Activated carbon made from Tanjung Tabalong coal was investigated its absorption capability to organic and inorganic elements in industrial waste. Coal was carbonized at low temperature of 600C to produce semicoke, and then was activated at temperature of 700C with activation time of 120 minutes with water steam flow. The absorption capability of activated carbon to chemical oxygen demand (COD was performed using 2.5 and 9.0 g activated carbon for 250 ml and 300 ml COD waste respectively. The agitation time of each experiment were 30, 60, and 90 minutes. Atomic absorption spectrophotometer (AAS was used to analyze the COD waste. The result shows that 2.5 g activated carbon could absorb COD waste ranging from 6.9-67.5 %, while the utilization of 9 g could absorb COD waste ranging from 88.9 - 100 %. The more activated carbon and the longer time of agitation used in this experiment, the more the absorption of COD waste.

  4. Canonical correlations between chemical and energetic characteristics of lignocellulosic wastes

    Directory of Open Access Journals (Sweden)

    Thiago de Paula Protásio

    2012-09-01

    Full Text Available Canonical correlation analysis is a statistical multivariate procedure that allows analyzing linear correlation that may exist between two groups or sets of variables (X and Y. This paper aimed to provide canonical correlation analysis between a group comprised of lignin and total extractives contents and higher heating value (HHV with a group of elemental components (carbon, hydrogen, nitrogen and sulfur for lignocellulosic wastes. The following wastes were used: eucalyptus shavings; pine shavings; red cedar shavings; sugar cane bagasse; residual bamboo cellulose pulp; coffee husk and parchment; maize harvesting wastes; and rice husk. Only the first canonical function was significant, but it presented a low canonical R². High carbon, hydrogen and sulfur contents and low nitrogen contents seem to be related to high total extractives contents of the lignocellulosic wastes. The preliminary results found in this paper indicate that the canonical correlations were not efficient to explain the correlations between the chemical elemental components and lignin contents and higher heating values.

  5. Proposed Occupational Exposure Limits for Non-Carcinogenic Hanford Waste Tank Vapor Chemicals

    International Nuclear Information System (INIS)

    Poet, Torka S.; Timchalk, Chuck

    2006-01-01

    A large number of volatile chemicals have been identified in the headspaces of tanks used to store mixed chemical and radioactive waste at the U.S. Department of Energy (DOE) Hanford Site, and there is concern that vapor releases from the tanks may be hazardous to workers. Contractually established occupational exposure limits (OELs) established by the Occupational Safety and Health Administration (OSHA) and American Conference of Governmental Industrial Hygienists (ACGIH) do not exist for all chemicals of interest. To address the need for worker exposure guidelines for those chemicals that lack OSHA or ACGIH OELs, a procedure for assigning Acceptable Occupational Exposure Limits (AOELs) for Hanford Site tank farm workers has been developed and applied to a selected group of 57 headspace chemicals

  6. Proposed Occupational Exposure Limits for Non-Carcinogenic Hanford Waste Tank Vapor Chemicals

    Energy Technology Data Exchange (ETDEWEB)

    Poet, Torka S.; Timchalk, Chuck

    2006-03-24

    A large number of volatile chemicals have been identified in the headspaces of tanks used to store mixed chemical and radioactive waste at the U.S. Department of Energy (DOE) Hanford Site, and there is concern that vapor releases from the tanks may be hazardous to workers. Contractually established occupational exposure limits (OELs) established by the Occupational Safety and Health Administration (OSHA) and American Conference of Governmental Industrial Hygienists (ACGIH) do not exist for all chemicals of interest. To address the need for worker exposure guidelines for those chemicals that lack OSHA or ACGIH OELs, a procedure for assigning Acceptable Occupational Exposure Limits (AOELs) for Hanford Site tank farm workers has been developed and applied to a selected group of 57 headspace chemicals.

  7. A calibrated energy end-use model for the U.S. chemical industry

    International Nuclear Information System (INIS)

    Ozalp, N.; Hyman, B.

    2005-01-01

    The chemical industry is the second largest energy user after the petroleum industry in the United States. This paper provided a model for onsite steam and power generation in the chemical industry, as well as an end-use of the industrial gas manufacturing sector. The onsite steam and power generation model included the actual conversion efficiencies of prime movers in the sector. The energy end-use model also allocated combustible fuel and renewable energy inputs among generic end-uses including intermediate conversions through onsite power and steam generation. The model was presented in the form of a graphical depiction of energy flows. Results indicate that 35 per cent of the energy output from boilers is used for power generation, whereas 45 per cent goes directly to end-uses and 20 per cent to waste heat tanks for recovery in the chemical industry. The end-use model for the industrial gas manufacturing sector revealed that 42 per cent of the fuel input goes to onsite steam and power generation, whereas 58 per cent goes directly to end-uses. Among the end-uses, machine drive was the biggest energy user. It was suggested that the model is applicable to all other industries and is consistent with U.S. Department of Energy data for 1998. When used in conjunction with similar models for other years, it can be used to identify changes and trends in energy utilization at the prime mover level of detail. An analysis of the economic impact of energy losses can be based on the results of this model. Cascading of waste heat from high temperature processes to low temperature processes could be integrated into the model. 20 refs., 4 tabs., 8 figs

  8. PENGOLAHAN LIMBAH CAIR INDUSTRI SUSU (Liquid Waste Management in Milk Factory

    Directory of Open Access Journals (Sweden)

    Wagini Wagini

    2002-03-01

    Full Text Available ABSTRAK Telah dilakukan suatu penelitian untuk mengetahui kondisi limbah cair industri susu. hasil penelitian menunjukkan bahwa limbah cair industri susu mengandung zat-zat pencemar dalam tingkat yang membahayakan lingkungan, sehingga limbah cair tersebut perlu didaur ulang. Untuk itu diperlukan suatu instalasi peralatan yang mampu mengolah limbah tersebut. Pada penelitian ini proses pengolahan dilakukan dengan mengkombinasikan proses-proses pengolahan secara Fisika, Kimia dan Biologi. Dengan tahapan proses pengolahan yang dipilih meliputi; Proses equalisasi, proses anaerob, proses aerasi, lumpur aktif, proses sedimentasi, proses koagulasi-flokulasi, proses sedimentasi, proses flotasi, proses pengendapan partikel ringan, proses penyaringan dengan pasir dan arang aktif.    Kualitas air hasil pengolahan dianalisa secara Fisika, Kimia dan Biologi melalui parameter-parameter: suhu, kekeruhan, zat padat tersuspensi, zat padat terlarut, daya hantar listrik, PH, BOD, COD dan jumlah bakteri. Penelitian ini menunjukkan air hasil pengolahan aman untuk dibuang ke lingkungan.   ABSTRACT A research to identify the condition of milk industry liquid waste was conducted. The result showed that the waste contained pollutants at the level the endangered the environment. Therefore, the waste had to be recycled in which a liquid waste treatment installation is needed. In this research, the process of milk industry liquid waste was done by combining processing techniques of physics, chemistry and biology. The processing steps include the processes of equalization, anaerobe, aeration, sedimentation, coagulation-flocculation, sedimentation, flotation, sedimentation, filtering with sand and activated carbon. The water resulted from the processes was analyzed in terms of physical, chemical and biological characteristics e.g. temperature, turbidity, suspended solid, solutes solid, conductivity, pH, BOD, COD and amount of bacteria. This research, shows that the water

  9. A survey of economic indices of plastic wastes recycling industry

    Directory of Open Access Journals (Sweden)

    Malek Hassanpour

    2015-11-01

    Full Text Available Numerous small recycling units of plastic wastes have been currently constructed heedless to study of economic indices in Iran. Pay attention to the prominent performance of the industrial sector for economic development and its priority for fortifying other sectors to implement job opportunities, survey of the economic indices beckon the stakeholders and industries owners. The main objective of this study was a survey of economic indices in small recycling unit of plastic wastes. Therefore, the practice of computing the economic indices was performed using empirical equations, professional experiences and observations in site of the industry in terms of sustainability performance. Current study had shown the indices values such as value-added percent, profit, annual income, breakeven point, value-added, output value, data value, variable cost of good unit and production costs were found 62%, $ 366558, $ 364292.6, $ 100.34, $ 423451.25, $ 255335.75, $ 678787, $ 389.65 and $ 314494.4 respectively. The breakeven point about 15.93%, the time of return on investment about 1.12 (13.7 months were represented that this industry slightly needs long time to afford the employed capital and starts making a profit.

  10. Use of food waste, fish waste and food processing waste for China's aquaculture industry: Needs and challenge.

    Science.gov (United States)

    Mo, Wing Yin; Man, Yu Bon; Wong, Ming Hung

    2018-02-01

    China's aquaculture industry is growing dramatically in recent years and now accounts for 60.5% of global aquaculture production. Fish protein is expected to play an important role in China's food security. Formulated feed has become the main diet of farmed fish. The species farmed have been diversified, and a large amount of 'trash fish' is directly used as feed or is processed into fishmeal for fish feed. The use of locally available food waste as an alternative protein source for producing fish feed has been suggested as a means of tackling the problem of sourcing safe and sustainable feed. This paper reviews the feasibility of using locally available waste materials, including fish waste, okara and food waste. Although the fishmeal derived from fish waste, okara or food waste is less nutritious than fishmeal from whole fish or soybean meal, most fish species farmed in China, such as tilapia and various Chinese carp, grow well on diets with minimal amounts of fishmeal and 40% digestible carbohydrate. It can be concluded that food waste is suitable as a component of the diet of farmed fish. However, it will be necessary to revise regulations on feed and feed ingredients to facilitate the use of food waste in the manufacture of fish feed. Copyright © 2017 Elsevier B.V. All rights reserved.

  11. Chemically treated carbon black waste and its potential applications

    Energy Technology Data Exchange (ETDEWEB)

    Dong, Pengwei; Maneerung, Thawatchai; Ng, Wei Cheng; Zhen, Xu [NUS Environmental Research Institute, National University of Singapore, 1 Create Way, Create Tower #15-02, 138602 (Singapore); Dai, Yanjun [School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Tong, Yen Wah [NUS Environmental Research Institute, National University of Singapore, 1 Create Way, Create Tower #15-02, 138602 (Singapore); Department of Chemical and Biomolecular Engineering, National University of Singapore, 4 Engineering Drive 4, 117585 (Singapore); Ting, Yen-Peng [Department of Chemical and Biomolecular Engineering, National University of Singapore, 4 Engineering Drive 4, 117585 (Singapore); Koh, Shin Nuo [Sembcorp Industries Ltd., 30 Hill Street #05-04, 179360 (Singapore); Wang, Chi-Hwa, E-mail: chewch@nus.edu.sg [Department of Chemical and Biomolecular Engineering, National University of Singapore, 4 Engineering Drive 4, 117585 (Singapore); Neoh, Koon Gee, E-mail: chenkg@nus.edu.sg [Department of Chemical and Biomolecular Engineering, National University of Singapore, 4 Engineering Drive 4, 117585 (Singapore)

    2017-01-05

    Highlights: • Hazardous impurities separated from carbon black waste with little damage to solid. • Heavy metals were effectively removed from carbon black waste by HNO{sub 3} leaching. • Treated carbon black waste has high adsorption capacity (∼356.4 mg{sub dye}/g). • Carbon black waste was also found to show high electrical conductivity (10 S/cm). - Abstract: In this work, carbon black waste – a hazardous solid residue generated from gasification of crude oil bottom in refineries – was successfully used for making an absorbent material. However, since the carbon black waste also contains significant amounts of heavy metals (especially nickel and vanadium), chemical leaching was first used to remove these hazardous impurities from the carbon black waste. Acid leaching with nitric acid was found to be a very effective method for removal of both nickel and vanadium from the carbon black waste (i.e. up to 95% nickel and 98% vanadium were removed via treatment with 2 M nitric acid for 1 h at 20 °C), whereas alkali leaching by using NaOH under the same condition was not effective for removal of nickel (less than 10% nickel was removed). Human lung cells (MRC-5) were then used to investigate the toxicity of the carbon black waste before and after leaching. Cell viability analysis showed that the leachate from the original carbon black waste has very high toxicity, whereas the leachate from the treated samples has no significant toxicity. Finally, the efficacy of the carbon black waste treated with HNO{sub 3} as an absorbent for dye removal was investigated. This treated carbon black waste has high adsorption capacity (∼361.2 mg {sub dye}/g {sub carbonblack}), which can be attributed to its high specific surface area (∼559 m{sup 2}/g). The treated carbon black waste with its high adsorption capacity and lack of cytotoxicity is a promising adsorbent material. Moreover, the carbon black waste was found to show high electrical conductivity (ca. 10 S

  12. Physico-chemical characterization of slag waste coming from GICC thermal power plant

    Energy Technology Data Exchange (ETDEWEB)

    Acosta, A.; Aineto, M.; Iglesias, I. [Laboratory of Applied Mineralogy, Universidad de Castilla-La Mancha, Ciudad Real Madrid (Spain); Romero, M.; Rincon, J.Ma. [The Glass-Ceramics Laboratory, Insituto Eduardo Torroja de Ciencias de la Construccion, CSIC, c/Serrano Galvache s/n, 28033, Madrid (Spain)

    2001-09-01

    The new gas installations of combined cycle (GICC) thermal power plants for production of electricity are more efficient than conventional thermal power plants, but they produce a high quantity of wastes in the form of slags and fly ashes. Nowadays, these by-products are stored within the production plants with, until now, no applications of recycling in other industrial processes. In order to evaluate the capability of these products for recycling in glass and ceramics inductory, an investigation for the full characterization has been made by usual physico-chemical methods such as: chemical analysis, mineralogical analysis by XRD, granulometry, BET, DTA/TG, heating microscopy and SEM/EDX.

  13. Chemical and mechanical decontamination processes to minimize secondary waste decommissioning

    International Nuclear Information System (INIS)

    Enda, M.; Ichikawa, N.; Yaita, Y.; Kanasaki, T.; Sakai, H.

    2008-01-01

    In the decommissioning of commercial nuclear reactors in Japan, prior to the dismantling of the nuclear power plants, there are plans to use chemical techniques to decontaminate reactor pressure vessels (RPVs), internal parts, primary loop recirculation systems (PLRs), reactor water clean up systems (RWCUs), etc., so as to minimize radiation sources in the materials to be disposed of. After dismantling the nuclear power plants, chemical and mechanical decontamination techniques will then be used to reduce the amounts of radioactive metallic waste. Toshiba Corporation has developed pre-dismantling and post-dismantling decontamination systems. In order to minimize the amounts of secondary waste, the T-OZON process was chosen for decontamination prior to the dismantling of nuclear power plants. Dismantling a nuclear power plant results in large amounts of metallic waste requiring decontamination; for example, about 20,000 tons of such waste is expected to result from the dismantling of a 110 MWe Boiling Water Reactor (BWR). Various decontamination methods have been used on metallic wastes in preparation for disposal in consideration of the complexity of the shapes of the parts and the type of material. The materials in such nuclear power plants are primarily stainless steel and carbon steel. For stainless steel parts having simple shapes, such as plates and pipes, major sources of radioactivity can be removed from the surface of the parts by bipolar electrolysis (electrolyte: H 2 SO 4 ). For stainless steel parts having complicated shapes, such as valves and pumps, major sources of radioactivity can be removed from the surfaces by redox chemical decontamination treatments (chemical agent: Ce(IV)). For carbon steel parts having simple shapes, decontamination by blasting with zirconia grit is effective in removing major sources of radioactivity at the surface, whereas for carbon steel parts having complicated shapes, major sources of radioactivity can be removed from

  14. Influence of industrial solid waste addition on properties of soil-cement bricks

    OpenAIRE

    Siqueira, F. B.; Amaral, M. C.; Bou-Issa, R. A.; Holanda, J. N. F.

    2016-01-01

    Abstract The reuse of pollutant solid wastes produced in distinct industrial activities (avian eggshell waste and welding flux slag waste) as a source of alternative raw material for producing soil-cement bricks for civil construction was investigated. Soil-cement bricks containing up to 30 wt% of industrial solid waste were uniaxially pressed and cured for 28 days. Special emphasis is given on the influence of solid waste addition on the technical properties (as such volumetric shrinkage, wa...

  15. Waste energy recovery in the industry in the ECE region

    International Nuclear Information System (INIS)

    1985-01-01

    In the ECE region industry accounts for about 44 per cent of total final energy consumption, 50-55 per cent of which is ''lost''. Since the early 1970s the efficiency of energy use has improved by 5 or 6 percentage points. The potential for further cost-effective savings is estimated at 10 to 20 percentage points, depending on the type of industrial activity, kind of waste energy, availability of outlets, investment strategies, awareness of the significantly improved technical possibilities and degree of co-operation between energy specialists and production engineers, equipment manufacturers, and industrial sectors at the national and international levels. The present publication argues the case for secondary energy recovery (SER) by end-users and international co-operation in technical, economic, environmental and methodological fields. It is based on data compiled by the secretariat of the Economic Commission for Europe on 1 June 1984 and given general distribution. Refs, figs and tabs

  16. High temperature absorption compression heat pump for industrial waste heat

    DEFF Research Database (Denmark)

    Reinholdt, Lars; Horntvedt, B.; Nordtvedt, S. R.

    2016-01-01

    Heat pumps are currently receiving extensive interest because they may be able to support the integration of large shares of fluctuating electricity production based on renewable sources, and they have the potential for the utilization of low temperature waste heat from industry. In most industries......, the needed temperature levels often range from 100°C and up, but until now, it has been quite difficult to find heat pump technologies that reach this level, and thereby opening up the large-scale heat recovery in the industry. Absorption compression heat pumps can reach temperatures above 100°C......, and they have proved themselves a very efficient and reliable technology for applications that have large temperature changes on the heat sink and/or heat source. The concept of Carnot and Lorenz efficiency and its use in the analysis of system integration is shown. A 1.25 MW system having a Carnot efficiency...

  17. Enhanced Bio-Ethanol Production from Industrial Potato Waste by Statistical Medium Optimization

    OpenAIRE

    Izmirlioglu, Gulten; Demirci, Ali

    2015-01-01

    Industrial wastes are of great interest as a substrate in production of value-added products to reduce cost, while managing the waste economically and environmentally. Bio-ethanol production from industrial wastes has gained attention because of its abundance, availability, and rich carbon and nitrogen content. In this study, industrial potato waste was used as a carbon source and a medium was optimized for ethanol production by using statistical designs. The effect of various medium componen...

  18. System analysis of industrial waste management: A case study of industrial plants located between Tehran and Karaj

    OpenAIRE

    Mohammad Amin Karami; Mohsen Sadani; Mehdi Farzadkia; Nezam Mirzaei; Anvar Asadi

    2015-01-01

    Aims: In this study, management of industrial waste in industries located between Tehran and Karaj in 2009-2010 was examined. Materials and Methods: This is a cross-sectional study which was done by site survey (Iranian environmental protection organization) questionnaire usage and results analysis. This questionnaire was consisted of 45 questions about industrial waste, quantity, quality, and management. A total number of industries with over 50 employees was 283, and Stratified sampling...

  19. Exploring of Agro Waste (Pineapple Leaf, Corn Stalk, and Napier Grass) by Chemical Composition and Morphological Study

    OpenAIRE

    Angzzas Sari Mohd Kassim; Halizah Awang; Ashuvila Mohd Aripin

    2013-01-01

    Malaysia is a country that is a rich source of agricultural waste material. Three different crops were studied here, including pineapple (Ananas comosus) leaf, corn (Zea mays) stalk, and Napier grass (Pennisetum purpureum). These crops are characterized as agricultural waste materials in Malaysia and have a high potential to be used as alternative fibers for the paper making industry. The objective of this work was to analyze the chemical composition of pineapple leaf, corn stalk, and Napier ...

  20. Characterisation of Radioactive Waste located at Shelter Industrial Site

    International Nuclear Information System (INIS)

    Brown, T.D.; Billon, F.; Rudko, V.M.; Batiy, V.G.; Panasyuk, N.I.

    2001-04-01

    As a result of the accident at the unit 4 reactor at the Chernobyl Nuclear Power Plant on the 26 April 1986 there was widespread radioactive contamination of the surrounding area. The area immediately surrounding Unit 4, referred to as the Industrial Site, was very heavily contaminated with fuel and core debris ejected from the reactor. Immediate action was undertaken to reduce the local radiation hazard and mitigate the potential of secondary contamination of the environment. This action involved (a) the removal and collection of fuel fragments (b) removal of the top layer of soil around unit 4 and (c) preparation of a new surface over the Industrial Site. This new surface is referred to colloquially as the Techno-genic Layer. This report provides an overview of a project undertaken for DG-Environment of European Commission by a Consortium consisting of SGN (France) and AEA Technology (UK) working in collaboration with the Organisation, National Academy of Sciences of Ukraine; the Interdisciplinary Scientific and Technical Centre Shelter''. The project consisted of 3 Phases and a total of 14 Tasks. The main purpose of Phase 1 was to review previous work and available information and data on the contamination of the Industrial Site, construction of the Techno-genic Layer, Buttress and Pioneer Walls. Phase 2 was directed at additional measurements being carried out on existing boreholes and core samples to improve and/or substantiate existing information and data. Estimation of likely radioactive waste arisings, recovery procedures and a generalised strategy with indicative costs for the management of the waste was also covered by Phase 2. In Phase 3 new boreholes (3 off) were drilled and subsequently investigated. The justification behind Phase 3 was the desire/need to obtain more reliable information on the so-called high-active waste buried in the Industrial Site. (author)

  1. Recycled water reuse permit renewal application for the materials and fuels complex industrial waste ditch and industrial waste pond

    Energy Technology Data Exchange (ETDEWEB)

    Name, No

    2014-10-01

    This renewal application for the Industrial Wastewater Reuse Permit (IWRP) WRU-I-0160-01 at Idaho National Laboratory (INL), Materials and Fuels Complex (MFC) Industrial Waste Ditch (IWD) and Industrial Waste Pond (IWP) is being submitted to the State of Idaho, Department of Environmental Quality (DEQ). This application has been prepared in compliance with the requirements in IDAPA 58.01.17, Recycled Water Rules. Information in this application is consistent with the IDAPA 58.01.17 rules, pre-application meeting, and the Guidance for Reclamation and Reuse of Municipal and Industrial Wastewater (September 2007). This application is being submitted using much of the same information contained in the initial permit application, submitted in 2007, and modification, in 2012. There have been no significant changes to the information and operations covered in the existing IWRP. Summary of the monitoring results and operation activity that has occurred since the issuance of the WRP has been included. MFC has operated the IWP and IWD as regulated wastewater land treatment facilities in compliance with the IDAPA 58.01.17 regulations and the IWRP. Industrial wastewater, consisting primarily of continuous discharges of nonhazardous, nonradioactive, routinely discharged noncontact cooling water and steam condensate, periodic discharges of industrial wastewater from the MFC facility process holdup tanks, and precipitation runoff, are discharged to the IWP and IWD system from various MFC facilities. Wastewater goes to the IWP and IWD with a permitted annual flow of up to 17 million gallons/year. All requirements of the IWRP are being met. The Operations and Maintenance Manual for the Industrial Wastewater System will be updated to include any new requirements.

  2. Coal chemical industry and its sustainable development in China

    International Nuclear Information System (INIS)

    Xie, Kechang; Li, Wenying; Zhao, Wei

    2010-01-01

    China is rich in coal resource, which is vital for energy security in this country. In early 21st century, the coal chemical industry in China will be oriented to the development of high efficiency, safety, cleanliness, and optimum utilization. In this review, the authors present an introduction to the utilization status of primary energy production and consumption in China. Since 2005, fundamental research studies, supported by the Ministry of Science and Technology of Chinese National Basic Research Program, have been carried out at Taiyuan University of Technology. The Ministry stresses that the new coal chemical industry should be developed in a sustainable manner to realize effective utilization of energy. Moreover, upgrading the high technology to improve actively the recycling processes of coal chemical engineering is of strategic importance to realize the modern coal chemical engineering.

  3. The chemical industry - a danger to nuclear power plants

    International Nuclear Information System (INIS)

    Voigtsberger, P.

    1976-01-01

    Nuclear power stations could contaminate large areas with radioactivity when destroyed by strong external influences. In Germany, authorities try to cope with this danger firstly by making certain demands on the strength of the reactor shell and secondly by imposing strict safety regulations on dangerous industrial plants in the surroundings of the reactor. In the case of chemical industry, this means: If a chemical plant and a nuclear reactor lie closely together, special stress is given to explosion pretection measures in the form of primary explosion protection, e.g. strong sealing of inflammable gases and liquids handled in the immediate neighbourhood of the reactor. (orig.) [de

  4. THE IMPACT OF INDUSTRIAL WASTE LANDFILL ON THE ENVIRONMENT

    Directory of Open Access Journals (Sweden)

    Monika Janas

    2017-06-01

    Full Text Available The aim of the study is to assess the environmental impact of a shut down industrial waste landfill. A detailed analysis of the quality of groundwater around the landfill in the years 1995-2016 was conducted. Assessment of the status of groundwater in the landfill area was made based on the results of monitoring tests. It includes the measurement of pH, specific electrical conductivity (SEC and the content of chlorides, sulfates, phosphates, heavy metals: copper (Cu, lead (Pb, chromium (Cr and a number of other pollution indicators. The analysis confirms that the landfill during the operation did not constitute a threat because of a number of employed security measures and sealing layers. Only in recent years, the industrial waste landfill which is already out of operation has become an extremely serious environmental threat. The results of water analyses from the piezometers clearly indicate that there is a problem of groundwater contamination. There was a significant increase in the value of some of the analyzed indicators (such as chlorides and sulfates, mainly in the piezometers located on the flow line of groundwater in the landfill area. The observed situation is probably a result of damage to the sealing layers and leaching of pollutants from waste deposited in the landfill by rain water.

  5. Study of commercial chemical additives for cementation of radioactive waste

    International Nuclear Information System (INIS)

    Mota Vieira, V.; Oliveira, C.C. de

    2015-01-01

    In this research it has been studied the effects of chemical additives (admixtures) in the cementation process of radioactive wastes, which are used to improve the properties of waste cementation process, both of the paste and of the solidified product. However there are a large variety of these materials that are frequently changed or taken out of the market, then it is essential to know the commercially available materials and their effects. The tests were carried out with a solution simulating the evaporator concentrate waste coming from PWR nuclear reactors. It was cemented using two formulations, A and B, incorporating higher or lower amount of waste, respectively. It was added chemical admixtures from two manufacturers (S and H), which were: accelerators, set retarders and superplasticizers. The experiments were organized by a factorial design 23. The measured parameters were the viscosity, the setting time, the paste and product density and the compressive strength. In this study we performed comparative analyzes of the results of compressive strength at age of 28 and 90 days and between the densities of the samples at the same ages. The compressive strength test at age of 28 days is considered a parameter essential issues related to security handling, transport and storage of cemented waste product. The results showed that the addition of accelerators improved the compressive strength of the cemented product, but presented lower values density products. (authors)

  6. Biodiesel biorefinery: opportunities and challenges for microbial production of fuels and chemicals from glycerol waste.

    Science.gov (United States)

    Almeida, João R M; Fávaro, Léia C L; Quirino, Betania F

    2012-07-18

    The considerable increase in biodiesel production worldwide in the last 5 years resulted in a stoichiometric increased coproduction of crude glycerol. As an excess of crude glycerol has been produced, its value on market was reduced and it is becoming a "waste-stream" instead of a valuable "coproduct". The development of biorefineries, i.e. production of chemicals and power integrated with conversion processes of biomass into biofuels, has been singled out as a way to achieve economically viable production chains, valorize residues and coproducts, and reduce industrial waste disposal. In this sense, several alternatives aimed at the use of crude glycerol to produce fuels and chemicals by microbial fermentation have been evaluated. This review summarizes different strategies employed to produce biofuels and chemicals (1,3-propanediol, 2,3-butanediol, ethanol, n-butanol, organic acids, polyols and others) by microbial fermentation of glycerol. Initially, the industrial use of each chemical is briefly presented; then we systematically summarize and discuss the different strategies to produce each chemical, including selection and genetic engineering of producers, and optimization of process conditions to improve yield and productivity. Finally, the impact of the developments obtained until now are placed in perspective and opportunities and challenges for using crude glycerol to the development of biodiesel-based biorefineries are considered. In conclusion, the microbial fermentation of glycerol represents a remarkable alternative to add value to the biodiesel production chain helping the development of biorefineries, which will allow this biofuel to be more competitive.

  7. Biodiesel production using oil from fish canning industry wastes

    International Nuclear Information System (INIS)

    Costa, J.F.; Almeida, M.F.; Alvim-Ferraz, M.C.M.; Dias, J.M.

    2013-01-01

    Highlights: • A process was established to produce biodiesel from fish canning industry wastes. • Biodiesel production was enabled by an acid esterification pre-treatment. • Optimization studies showed that the best catalyst concentration was 1 wt.% H 2 SO 4 . • There was no advantage when a two-step alkali transesterification was employed. • Waste oil from olive oil bagasse could be used to improve fuel quality. - Abstract: The present study evaluated biodiesel production using oil extracted from fish canning industry wastes, focusing on pre-treatment and reaction conditions. Experimental planning was conducted to evaluate the influence of acid catalyst concentration (1–3 wt.% H 2 SO 4 ) in the esterification pre-treatment and the amount of methanolic solution (60–90 vol.%) used at the beginning of the further two-step alkali transesterification reaction. The use of a raw-material mixture, including waste oil obtained from olive oil bagasse, was also studied. The results from experimental planning showed that catalyst concentration mostly influenced product yield and quality, the best conditions being 1 wt.% catalyst and 60 vol.% of methanolic solution, to obtain a product yield of 73.9 wt.% and a product purity of 75.5 wt.%. Results from a one-step reaction under the selected conditions showed no advantage of performing a two-step alkali process. Although under the best conditions several of the biodiesel quality parameters were in agreement with standard specifications, a great variation was found in the biodiesel acid value, and oxidation stability and methyl ester content did not comply with biodiesel quality standards. Aiming to improve fuel quality, a mixture containing 80% waste olive oil and 20% of waste fish oil was evaluated. Using such mixture, biodiesel purity increased around 15%, being close to the standard requirements (96.5 wt.%), and the oxidation stability was in agreement with the biodiesel quality standard values (⩾6 h), which

  8. Chemical recycle of plastics waste; Hai purasuchikku no kemikaru risaikuru

    Energy Technology Data Exchange (ETDEWEB)

    Miyake, A. [Sumitomo Chemical Co. Ltd., Osaka (Japan)

    1997-11-01

    Chemical recycling of the wasted plastics contains from regeneration to monomer as a constructing component in the case of single element polymer to conversion to fuel oil through thermal decomposition of the mixed wasted plastics and application to chemical raw material. Polymethyl methacrylate (PMMA) decomposes to methylmethacrylate (MMA) monomer with high selection rate at max temperature of 400{+-}50degC. The Mitsubishi Rayon Co., Ltd. Signed a cooperative development contract on the recycling technique of PMMA The ICI., Ltd., Great Britain. Depolymerization technique of Polyethylene terephthalate (PET) is already used actually on methanolysis with Coca-Cola Corp. (Hoechst-Celanese Corp.) and glycolysis with Pepsi-Cola Corp. (Goodyear Inc.). The chemical recycle due to thermal decomposition of the mixed wasted plastics is established as a technique of gasification of the mixed wasted plastics to generate methanol in Japan by the Mitsubishi Heavy Ind., Ltd., and is operated in a pilot plant of 2 ton/day. Here was summarized on these trends in and out of Japan. 29 refs., 5 figs., 4 tab.

  9. Recycled lightweight concrete made from footwear industry waste and CDW.

    Science.gov (United States)

    Lima, Paulo Roberto Lopes; Leite, Mônica Batista; Santiago, Ediela Quinteiro Ribeiro

    2010-06-01

    In this paper two types of recycled aggregate, originated from construction and demolition waste (CDW) and ethylene vinyl acetate (EVA) waste, were used in the production of concrete. The EVA waste results from cutting off the EVA expanded sheets used to produce insoles and innersoles of shoes in the footwear industry. The goal of this study was to evaluate the influence of the use of these recycled aggregates as replacements of the natural coarse aggregate, upon density, compressive strength, tensile splitting strength and flexural behavior of recycled concrete. The experimental program was developed with three w/c ratios: 0.49, 0.63 and 0.82. Fifteen mixtures were produced with different aggregate substitution rates (0%, 50% EVA, 50% CDW, 25% CDW-25% EVA and 50% CDW-50% EVA), by volume. The results showed that it is possible to use the EVA waste and CDW to produce lightweight concrete having semi-structural properties. Copyright 2010 Elsevier Ltd. All rights reserved.

  10. Treatment systems for liquid wastes generated in chemical analysis laboratories

    International Nuclear Information System (INIS)

    Linda Berrio; Oscar Beltran; Edison Agudelo; Santiago Cardona

    2012-01-01

    Nowadays, handling of liquid wastes from chemical analysis laboratories is posing problems to different public and private organizations because of its requirements of an integrated management. This article reviews various treatment technologies and its removal efficiencies in order to establish criteria for selecting the system and the appropriate variables to achieve research objectives as well as environmental sustainability. Review begins with a description of the problem and continues with the study of treatments for laboratory wastes. These technologies are segregated into physicochemical and biological treatments that comprise a variety of processes, some of which are considered in this review.

  11. Industrial hygiene survey. CF Chemicals, Inc., Bartow, Florida

    International Nuclear Information System (INIS)

    Stephenson, F.; Cassady, M.

    1977-10-01

    An industrial hygiene survey was conducted by NIOSH at CF Chemicals, Bartow, Florida on August 9-12, 1976 as part of a study of the phosphate industry. A description is given of the plant, and the medical, safety, and industrial hygiene programs. During the study, 8-hour time weighted averages were determined for exposure to arsenic, cadmium, chromium, vanadium, phosphoric acid, and sulfuric acid for workers involved in cleaning out phosphoric acid reactor vessels. General area samples were collected for fluorides, radon, and uranium. The results came within the OSHA standards except for two fluoride samples

  12. Industrial hygiene survey. IMC, Phosphate Chemical Complex, New Wales, Florida

    International Nuclear Information System (INIS)

    Stephenson, F.; Cassady, M.

    1977-10-01

    An industrial hygiene survey was conducted by NIOSH at IMC Phosphate Chemical Complex, New Wales, Florida, on June 7-11, 1976, as part of a study of the phosphate industry. Phosphate fertilizer manufacturing, the plant, and the medical, safety, and industrial hygiene programs are described. During the study 8-hour time weighted averages were determined for exposure to arsenic, cadmium, chromium, vanadium, phosphoric acid, and sulfuric acid for workers involved in cleaning out phosphoric acid reactor vessels. General area samples were collected for fluorides, radon, and uranium. Several samples were above the NIOSH recommended levels for arsenic and chromium

  13. Industrial wastes guide for Alsace; Guide des dechets de l`entreprise Alsace

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-01-01

    This guide is aimed for industrial plant managers and gives comprehensive information on industrial waste management: effects of wastes on the environment (water, air, soil), waste processing limitations in Alsace, new regulations, taxes and incentives concerning waste processing in France, and references of national and regional (Alsace) administration and industrial agencies that are related with pollution abatement and control and waste management. The different types of wastes are reviewed, from papers to toxic solvents, with information given on volumes, processes, operators, processing equipment and equipment distributors

  14. Optimum Resource Allocation and Eliminating Waste Inside Food Industry

    Directory of Open Access Journals (Sweden)

    Chandru Nagarajan Sathiyabama

    2013-06-01

    Full Text Available This article seeks to allocate optimum resources for wrapping section and suggesting a suitable method that need to be in place for successful elimination of waste inside the food industry wrapping section. It also includes identifying the main reasons for various types of wastages inside wrapping section and cost of all the wastages. The paper is based on the observation and research using the approach of lean tools and techniques. The methodology used for evaluating data is value stream mapping and some statistical SPSS tools for analysis. Data’s are real and are gathered from three different production shifts inside a food industry wrapping section. The main reasons for wastages inside the wrapping section are highlighted. Finally, the paper was concluded by estimating total cost of wastages and recommended suitable way to save the wastage costs. The need of change of jaws inside the wrapping machines, regular maintenance of all machines throughout the industry and training the personnel are recommended. The possible methods along with its benefits to reduce waste, operators, improve productivity and business growth was also highlighted.

  15. Anaerobic treatment with biogas recovery of beverage industry waste water

    International Nuclear Information System (INIS)

    Cacciari, E.; Zanoni, G.

    1992-01-01

    This paper briefly describes the application, by a leading Italian non-alcoholic beverage firm, of an up-flow anaerobic sludge blanket process in the treatment of waste water deriving from the production and bottling of beverages. In addition to describing the key design, operation and performance characteristics of the treatment process, the paper focuses on the economic benefits being obtained through the use of the innovative expansive sludge bed anaerobic digestion system which has proven itself to be particularly suitable for the treatment of food and beverage industry liquid wastes. The system, which has already been operating, with good results, for six months, has shown itself to be capable of yielding overall COD removal efficiencies of up to 94.8% and of producing about 0.43 Ncubic meters of biogas per kg of removed COD

  16. Anaerobic treatment with biogas recovery of beverage industry waste water

    Energy Technology Data Exchange (ETDEWEB)

    Cacciari, E; Zanoni, G [Passavant Impianti, Novate Milanese (Italy)

    1992-03-01

    This paper briefly describes the application, by a leading Italian non-alcoholic beverage firm, of an up-flow anaerobic sludge blanket process in the treatment of waste water deriving from the production and bottling of beverages. In addition to describing the key design, operation and performance characteristics of the treatment process, the paper focuses on the economic benefits being obtained through the use of the innovative expansive sludge bed anaerobic digestion system which has proven itself to be particularly suitable for the treatment of food and beverage industry liquid wastes. The system, which has already been operating, with good results, for six months, has shown itself to be capable of yielding overall COD removal efficiencies of up to 94.8% and of producing about 0.43 Ncubic meters of biogas per kg of removed COD.

  17. Determination of natural radionuclide level in industrial waste slags and evaluation of comprehensive utilization

    International Nuclear Information System (INIS)

    Li Ruixiang; Liu Xinhua; Gan Lin

    1994-09-01

    Natural radionuclide contents were measured in various industrial waste slags in China by a low background HPGe γ spectrometer and the radiological impact was estimated for some comprehensive utilization of these slags. Most waste slags can be used for building materials except for tailing and waste rock form nuclear industry

  18. An industrial ecology approach to municipal solid waste management: I. Methodology

    Science.gov (United States)

    Municipal solid waste (MSW) can be viewed as a feedstock for industrial ecology inspired conversions of wastes to valuable products and energy. The industrial ecology principle of symbiotic processes using waste streams for creating value-added products is applied to MSW, with e...

  19. Waste management '76 nuclear overview session industry viewpoint

    International Nuclear Information System (INIS)

    Carson, A.B.

    1976-01-01

    Lack of firm policy decisions and implementing regulations and program plans related to nuclear fuel cycle by-product wastes has become a major deterrent to progress in the constructive utilization of fission energy. In any event, the mismatch between waste management program accomplishments and perceived requirements has increased rather than decreased over recent years. Multi-agency programs and industry participation as well, at higher levels of effort than in the past, are required and are being initiated, but useful and lasting decisions still are some time off. From industry's viewpoint, all of the agency and industry programs related to waste management must be based on (a) a common view that no constructive activity is going to have zero personnel or environmental impact and that there generally will be a finite level of impact or risk to public health and safety that can be considered acceptable, and (b) consistent and rational consideration of what the levels of impact or risk are that can be considered acceptable in various circumstances. Regulatory requirements finally imposed must be related in some rational way to actual effects and their acceptable levels. Sound bases for timely decisions also require recognition of the fact that ''full and complete demonstration'' is not often really practical or necessary. Demonstration requirements for particular circumstances must be clearly defined and related to functional importance, extent of supporting technology and experience and other such rational factors. Finally, it is recognized that there are nontechnical issues the resolution of which are just as necessary to progress as the technical ones. However, such issues should not be allowed to lead to decisions or actions which are phenomenologically unsound or technically unsupported. After all, you might as well fall flat on your face as lean too far over backward

  20. Evaluation of improved chemical waste disposal and recovery methods for N reactor fuel fabrication operations: 1984 annual report

    International Nuclear Information System (INIS)

    Stewart, T.L.; Hartley, J.N.

    1984-12-01

    Pacific Northwest Laboratory personnel identified and evaluated alternative methods for recovery, recycle, and disposal of waste acids produced during N Reactor fuel operations. This work was conducted under a program sponsored by UNC Nuclear Industries, Inc.; the program goals were to reduce the volume of liquid waste by rejuvenating and recycling acid solutions and to generate a residual waste low in nitrates, fluorides, and metals. Disposal methods under consideration included nitric acid reclamation, grout encapsulation of final residual waste, nitrogen fertilizer production, biodenitrifaction, chemical or thermal destruction of NO 3 , and short-term impoundment of liquid NO 3 /SO 4 wastes. Preliminary testing indicated that the most feasible and practicable of these alternatives were (1) nitric acid reclamation followed by grouting of residual waste and (2) nitrogen fertilizer production. This report summarizes the investigations, findings, and recommendations for the 1984 fiscal year

  1. Fifty-Year Trends in the Chemical Industry: What Do They Mean for Chemical Education?

    Science.gov (United States)

    Tolman, Chadwick A.; Parshall, George W.

    1999-01-01

    Describes major changes that have occurred in the chemical industry over the last 50 years including trends in the development of products and processes, changes in chemical manufacturing, the globalization of business, and modifications of research laboratory practices. Discusses implications for chemistry education and predictions for future…

  2. Metal-organic frameworks for the removal of toxic industrial chemicals and chemical warfare agents.

    Science.gov (United States)

    Bobbitt, N Scott; Mendonca, Matthew L; Howarth, Ashlee J; Islamoglu, Timur; Hupp, Joseph T; Farha, Omar K; Snurr, Randall Q

    2017-06-06

    Owing to the vast diversity of linkers, nodes, and topologies, metal-organic frameworks can be tailored for specific tasks, such as chemical separations or catalysis. Accordingly, these materials have attracted significant interest for capture and/or detoxification of toxic industrial chemicals and chemical warfare agents. In this paper, we review recent experimental and computational work pertaining to the capture of several industrially-relevant toxic chemicals, including NH 3 , SO 2 , NO 2 , H 2 S, and some volatile organic compounds, with particular emphasis on the challenging issue of designing materials that selectively adsorb these chemicals in the presence of water. We also examine recent research on the capture and catalytic degradation of chemical warfare agents such as sarin and sulfur mustard using metal-organic frameworks.

  3. Radiation protection in the pharmaceutical-chemical industry

    International Nuclear Information System (INIS)

    Griesser, R.

    1992-01-01

    Some aspects of the use of ionizing radiation in research in the pharmaceutical and chemical industries will be discussed, the emphasis being placed on the handling of open radioactive materials in research laboratories. The compliance with official regulations and the preparation of company internal radiation protection regulations are described. 1 tab., 9 refs

  4. Near miss reporting in the chemical process industry: an overview

    NARCIS (Netherlands)

    Schaaf, van der T.W.

    1995-01-01

    The research programme described in this paper focuses on the human component of system failure in general, and more specifically on the design and implementation of information systems for registration and analysis of so called near misses (or: near accidents) in the chemical process industry. Its

  5. The chemical composition and industrial quality of Barite ...

    African Journals Online (AJOL)

    ... that the mineralization is of high industrial quality and compares favourably with the Azara barite deposits of the Benue Trough. The quality of the barite meets American Petroleum institute (API) requirements for use as drilling mud. KEYWORDS: Barite, mineralization, quality, chemical composition, southeastern Nigeria.

  6. Classification of solid industrial waste based on ecotoxicology tests using Daphnia magna: an alternative

    Directory of Open Access Journals (Sweden)

    William Gerson Matias

    2005-11-01

    Full Text Available The adequate treatment and final disposal of solid industrial wastes depends on their classification into class I or II. This classification is proposed by NBR 10.004; however, it is complex and time-consuming. With a view to facilitating this classification, the use of assays with Daphnia magna is proposed. These assays make possible the identification of toxic chemicals in the leach, which denotes the presence of one of the characteristics described by NBR 10.004, the toxicity, which is a sufficient argument to put the waste into class I. Ecotoxicological tests were carried out with ten samples of solid wastes of frequent production and, on the basis of the results from EC(I50/48h of those samples in comparison with the official classification of NBR 10.004, limits were established for the classification of wastes into class I or II. A coincidence in the classification of 50% of the analyzed samples was observed. In cases in which there is no coherence between the methods, the method proposed in this work classifies the waste into class I. These data are preliminary, but they reveal that the classification system proposed here is promising because of its quickness and economic viability.

  7. Optimal design of advanced distillation configuration for enhanced energy efficiency of waste solvent recovery process in semiconductor industry

    International Nuclear Information System (INIS)

    Chaniago, Yus Donald; Minh, Le Quang; Khan, Mohd Shariq; Koo, Kee-Kahb; Bahadori, Alireza; Lee, Moonyong

    2015-01-01

    Highlights: • Thermally coupled distillation process is proposed for waste solvent recovery. • A systematic optimization procedure is used to optimize distillation columns. • Response surface methodology is applied to optimal design of distillation column. • Proposed advanced distillation allows energy efficient waste solvent recovery. - Abstract: The semiconductor industry is one of the largest industries in the world. On the other hand, the huge amount of solvent used in the industry results in high production cost and potential environmental damage because most of the valuable chemicals discharged from the process are incinerated at high temperatures. A distillation process is used to recover waste solvent, reduce the production-related costs and protect the environment from the semiconductor industrial waste. Therefore, in this study, a distillation process was used to recover the valuable chemicals from semiconductor industry discharge, which otherwise would have been lost to the environment. The conventional sequence of distillation columns, which was optimized using the Box and sequential quadratic programming method for minimum energy objectives, was used. The energy demands of a distillation problem may have a substantial influence on the profitability of a process. A thermally coupled distillation and heat pump-assisted distillation sequence was implemented to further improve the distillation performance. Finally, a comparison was made between the conventional and advanced distillation sequences, and the optimal conditions for enhancing recovery were determined. The proposed advanced distillation configuration achieved a significant energy saving of 40.5% compared to the conventional column sequence

  8. Industrial waste treatment and application in rubber production

    Science.gov (United States)

    Pugacheva, I. N.; Popova, L. V.; Repin, P. S.; Molokanova, L. V.

    2018-03-01

    The paper provides for the relevance of various industrial waste treatment and application, as well as their secondary commercialization. It considers treatment of secondary polymer materials turning to additives applied in rubber production, in particular, in production of conveyor and V-type belts used in mechanical engineering. It is found that oligomers obtained from petroleum by-products can be used as an impregnating compound for fiber materials. Such adhesive treatment prior to introduction of impregnating compounds into elastomeric materials improves adhesion and complements performance of obtained composites.

  9. Characterization and extraction of gold contained in foundry industrial wastes

    International Nuclear Information System (INIS)

    Vite T, J.; Vite T, M.; Diaz C, A.; Carreno de Leon, C.

    1999-01-01

    Gold was characterized and leached in foundry sands. These wastes are product among others of the automotive industry where they are used as molds material which are contaminated by diverse metals during the foundry. To fulfil the leaching process four coupled thermostat columns were used. To characterize the solid it was used the X-ray diffraction technique. For the qualitative analysis it was used the Activation analysis technique. Finally, for the study of liquors was used the Plasma diffraction spectroscopy (Icp-As) technique. The obtained results show that the process which was used the thermostat columns was more efficient, than the methods traditionally recommended. (Author)

  10. Problems the chemical industry of Japan faces and future prospects

    Energy Technology Data Exchange (ETDEWEB)

    Ishida, Shin' ichi

    1989-01-01

    Industry proceeds for the fiscal 1988 are expected to increase remarkably as they did in the previous year with 4.9% increase in revenue and 18.8% increase in profit (ordinary profit) from the previous year. The conditions of material industry are especially favorable and chemical industry is also expected to prosper as it did in the previous year. Problems this prospering chemical industry is facing are introduced in this report. Firstly, it is necessary to improve productivity by adopting more information and promoting factory automation in order to strengthen competition. The future of chemical industry depends on the introduction of information. Secondly, as demands of users are becoming more diversified, and cycles of products shorter, shortening of development terms is essential. It is necessary, therefore, to predict the demands of users in advance and seek after custom products. Thirdly, selection of product bases is required; it might be necessary to consider producing some product items abroad. Moreover, it is desirable to increase investments in investigation and pursue creativity putting much stress on basic investigations. 2 figs., 11 tabs.

  11. Chemical Disposition of Plutonium in Hanford Site Tank Wastes

    Energy Technology Data Exchange (ETDEWEB)

    Delegard, Calvin H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jones, Susan A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2015-05-07

    This report examines the chemical disposition of plutonium (Pu) in Hanford Site tank wastes, by itself and in its observed and potential interactions with the neutron absorbers aluminum (Al), cadmium (Cd), chromium (Cr), iron (Fe), manganese (Mn), nickel (Ni), and sodium (Na). Consideration also is given to the interactions of plutonium with uranium (U). No consideration of the disposition of uranium itself as an element with fissile isotopes is considered except tangentially with respect to its interaction as an absorber for plutonium. The report begins with a brief review of Hanford Site plutonium processes, examining the various means used to recover plutonium from irradiated fuel and from scrap, and also examines the intermediate processing of plutonium to prepare useful chemical forms. The paper provides an overview of Hanford tank defined-waste–type compositions and some calculations of the ratios of plutonium to absorber elements in these waste types and in individual waste analyses. These assessments are based on Hanford tank waste inventory data derived from separately published, expert assessments of tank disposal records, process flowsheets, and chemical/radiochemical analyses. This work also investigates the distribution and expected speciation of plutonium in tank waste solution and solid phases. For the solid phases, both pure plutonium compounds and plutonium interactions with absorber elements are considered. These assessments of plutonium chemistry are based largely on analyses of idealized or simulated tank waste or strongly alkaline systems. The very limited information available on plutonium behavior, disposition, and speciation in genuine tank waste also is discussed. The assessments show that plutonium coprecipitates strongly with chromium, iron, manganese and uranium absorbers. Plutonium’s chemical interactions with aluminum, nickel, and sodium are minimal to non-existent. Credit for neutronic interaction of plutonium with these absorbers

  12. Chemical pathways for the formation of ammonia in Hanford wastes

    International Nuclear Information System (INIS)

    Stock, L.M.; Pederson, L.R.

    1997-12-01

    This report reviews chemical reactions leading to the formation of ammonia in Hanford wastes. The general features of the chemistry of the organic compounds in the Hanford wastes are briefly outlined. The radiolytic and thermal free radical reactions that are responsible for the initiation and propagation of the oxidative degradation reactions of the nitrogen-containing complexants, trisodium HEDTA and tetrasodium EDTA, are outlined. In addition, the roles played by three different ionic reaction pathways for the oxidation of the same compounds and their degradation products are described as a prelude to the discussion of the formation of ammonia. The reaction pathways postulated for its formation are based on tank observations, laboratory studies with simulated and actual wastes, and the review of the scientific literature. Ammonia derives from the reduction of nitrite ion (most important), from the conversion of organic nitrogen in the complexants and their degradation products, and from radiolytic reactions of nitrous oxide and nitrogen (least important)

  13. Chemical pathways for the formation of ammonia in Hanford wastes

    Energy Technology Data Exchange (ETDEWEB)

    Stock, L.M.; Pederson, L.R.

    1997-12-01

    This report reviews chemical reactions leading to the formation of ammonia in Hanford wastes. The general features of the chemistry of the organic compounds in the Hanford wastes are briefly outlined. The radiolytic and thermal free radical reactions that are responsible for the initiation and propagation of the oxidative degradation reactions of the nitrogen-containing complexants, trisodium HEDTA and tetrasodium EDTA, are outlined. In addition, the roles played by three different ionic reaction pathways for the oxidation of the same compounds and their degradation products are described as a prelude to the discussion of the formation of ammonia. The reaction pathways postulated for its formation are based on tank observations, laboratory studies with simulated and actual wastes, and the review of the scientific literature. Ammonia derives from the reduction of nitrite ion (most important), from the conversion of organic nitrogen in the complexants and their degradation products, and from radiolytic reactions of nitrous oxide and nitrogen (least important).

  14. Classification of solid industrial waste based on ecotoxicology tests using Daphnia magna: an alternative

    OpenAIRE

    William Gerson Matias; Vanessa Guimarães Machado; Cátia Regina Silva de Carvalho-Pinto; Débora Monteiro Brentano; Letícia Flohr

    2005-01-01

    The adequate treatment and final disposal of solid industrial wastes depends on their classification into class I or II. This classification is proposed by NBR 10.004; however, it is complex and time-consuming. With a view to facilitating this classification, the use of assays with Daphnia magna is proposed. These assays make possible the identification of toxic chemicals in the leach, which denotes the presence of one of the characteristics described by NBR 10.004, the toxicity, which is a s...

  15. Process Control Systems in the Chemical Industry: Safety vs. Security

    Energy Technology Data Exchange (ETDEWEB)

    Jeffrey Hahn; Thomas Anderson

    2005-04-01

    Traditionally, the primary focus of the chemical industry has been safety and productivity. However, recent threats to our nation’s critical infrastructure have prompted a tightening of security measures across many different industry sectors. Reducing vulnerabilities of control systems against physical and cyber attack is necessary to ensure the safety, security and effective functioning of these systems. The U.S. Department of Homeland Security has developed a strategy to secure these vulnerabilities. Crucial to this strategy is the Control Systems Security and Test Center (CSSTC) established to test and analyze control systems equipment. In addition, the CSSTC promotes a proactive, collaborative approach to increase industry's awareness of standards, products and processes that can enhance the security of control systems. This paper outlines measures that can be taken to enhance the cybersecurity of process control systems in the chemical sector.

  16. A survey of citizen's attitude to disposal sites of industrial waste and radioactive waste

    International Nuclear Information System (INIS)

    Ishizaka, Kaoru; Tanaka, Masaru; Tokizawa, Takayuki; Sato, Kazuhiko; Koga, Osamu

    2008-01-01

    This study aimed to investigate a risk perception about landfill sits for industrial waste or radioactive waste through the questionnaire survey. As a result, it was shown that most of people worried about health and environmental impact of radioactive waste; and moreover, high ratios of the peoples felt dangerous and scary sensuously. Public trust to the central government was very low. Over 60 percent of people do not trust that countermeasures will be taken at the times of accident' and nearly 70 percent of people do not trust that 'the information about the accident is disclosed'. Answers to questions concerning about public trust regarding countermeasures at the accident, information disclosure at the accident, environmental standard, and environmental technology show significant correlation with risk perception of landfill sites. (author)

  17. Thermal treatments available for destruction of industrial wastes. Application to the incineration of radioactive wastes

    International Nuclear Information System (INIS)

    Chevalier, Gerard.

    1981-08-01

    Both the collecting and processing circuits and the physicochemical laws of combustion and thermal degradation of industrial wastes are recalled. The various incineration processes are reviewed considering especially conversion of refuse to energy and recovery of raw materials either before or after treatment. Wastes are devided into three classes according to their physical state: solid, liquid or sludge, gas. Some processes based on pyrolysis in the absence of air or at sub-stoichiometric levels are presented. A similar study is carried out on radioactive wastes, taking into account the particular aspects raised by incineration. Operational devices are described and some lines of research about the application of new techniques are summarized. The results derived from laboratory or pilot plant experiments are presented [fr

  18. Waste Issues Associated with the Safe Movement of Hazardous Chemicals

    International Nuclear Information System (INIS)

    Dare, J. H.; Cournoyer, M. E.

    2002-01-01

    Moving hazardous chemicals presents the risk of exposure for workers engaged in the activity and others that might be in the immediate area. Adverse affects are specific to the chemicals and can range from minor skin, eye, or mucous membrane irritation, to burns, respiratory distress, nervous system dysfunction, or even death. A case study is presented where in the interest of waste minimization; original shipping packaging was removed from a glass bottle of nitric acid, while moving corrosive liquid through a security protocol into a Radiological Control Area (RCA). During the transfer, the glass bottle broke. The resulting release of nitric acid possibly exposed 12 employees with one employee being admitted overnight at a hospital for observation. This is a clear example of administrative controls to reduce the generation of suspect radioactive waste being implemented at the expense of employee health. As a result of this event, material handling procedures that assure the safe movement of hazardous chemicals through a security protocol into a radiological control area were developed. Specifically, hazardous material must be transferred using original shipping containers and packaging. While this represents the potential to increase the generation of suspect radioactive waste in a radiological controlled area, arguments are presented that justify this change. Security protocols for accidental releases are also discussed. In summary, the 12th rule of ''Green Chemistry'' (Inherently Safer Chemistry for Accident Prevention) should be followed: the form of a substance used in a chemical process (Movement of Hazardous Chemicals) should be chosen to minimize the potential for chemical accidents, including releases

  19. Waste Issues Associated with the Safe Movement of Hazardous Chemicals

    Energy Technology Data Exchange (ETDEWEB)

    Dare, J. H.; Cournoyer, M. E.

    2002-02-26

    Moving hazardous chemicals presents the risk of exposure for workers engaged in the activity and others that might be in the immediate area. Adverse affects are specific to the chemicals and can range from minor skin, eye, or mucous membrane irritation, to burns, respiratory distress, nervous system dysfunction, or even death. A case study is presented where in the interest of waste minimization; original shipping packaging was removed from a glass bottle of nitric acid, while moving corrosive liquid through a security protocol into a Radiological Control Area (RCA). During the transfer, the glass bottle broke. The resulting release of nitric acid possibly exposed 12 employees with one employee being admitted overnight at a hospital for observation. This is a clear example of administrative controls to reduce the generation of suspect radioactive waste being implemented at the expense of employee health. As a result of this event, material handling procedures that assure the safe movement of hazardous chemicals through a security protocol into a radiological control area were developed. Specifically, hazardous material must be transferred using original shipping containers and packaging. While this represents the potential to increase the generation of suspect radioactive waste in a radiological controlled area, arguments are presented that justify this change. Security protocols for accidental releases are also discussed. In summary, the 12th rule of ''Green Chemistry'' (Inherently Safer Chemistry for Accident Prevention) should be followed: the form of a substance used in a chemical process (Movement of Hazardous Chemicals) should be chosen to minimize the potential for chemical accidents, including releases.

  20. [Occupational digestive diseases in chemical industry workers of West Siberia].

    Science.gov (United States)

    Pomytkina, T E; Pershin, A N

    2010-01-01

    The high incidence of chronic digestive diseases is recorded in chemical industry workers exposed to the isolated action of noxious substances. The aim of the investigation was to make a hygienic assessment of the risk for occupational digestive diseases in chemical industry workers exposed to a combination of noxious drugs. The working conditions and the prevalence of digestive diseases were studied in 4120 workers engaged in chemical and auxiliary processes. Under the isolated action of noxious substances, the workers had an average of 35% increase in the incidence of digestive diseases than unexposed ones (p 4.0-11.1 and 3.5-10.7 times higher, respectively (p < 0.05) than in the unexposed subjects.

  1. New-Generation Aluminum Composite with Bottom Ash Industrial Waste

    Science.gov (United States)

    Mandal, A. K.; Sinha, O. P.

    2018-06-01

    Industrial waste bottom ash (BA) from a pulverized coal combustion boiler containing hard wear-resistant particles was utilized in this study to form an aluminum composite through a liquid metallurgy route. Composites comprising 5 wt.% and 10 wt.% bottom ash were characterized for their physiochemical, microstructural, mechanical, as well as tribological properties, along with pure aluminum. Scanning electron microscopy (SEM) microstructure revealed uniform distribution of BA particles throughout the matrix of the composite, whereas x-ray diffraction (XRD) analysis confirmed presence of aluminosilicate phase. Addition of 10 wt.% BA improved the Brinell hardness number (BHN) from 13 to 19 and ultimate tensile strength (UTS) from 71 MPa to 87 MPa, whereas ductility was adversely reduced after 5% BA addition. Incorporation of BA particles resulted in reduced dry sliding wear rates examined up to 80 N load compared with aluminum. Hence, such composites having lower cost could be applied as significantly hard, wear-resistant materials in applications in the automotive industry.

  2. New-Generation Aluminum Composite with Bottom Ash Industrial Waste

    Science.gov (United States)

    Mandal, A. K.; Sinha, O. P.

    2018-02-01

    Industrial waste bottom ash (BA) from a pulverized coal combustion boiler containing hard wear-resistant particles was utilized in this study to form an aluminum composite through a liquid metallurgy route. Composites comprising 5 wt.% and 10 wt.% bottom ash were characterized for their physiochemical, microstructural, mechanical, as well as tribological properties, along with pure aluminum. Scanning electron microscopy (SEM) microstructure revealed uniform distribution of BA particles throughout the matrix of the composite, whereas x-ray diffraction (XRD) analysis confirmed presence of aluminosilicate phase. Addition of 10 wt.% BA improved the Brinell hardness number (BHN) from 13 to 19 and ultimate tensile strength (UTS) from 71 MPa to 87 MPa, whereas ductility was adversely reduced after 5% BA addition. Incorporation of BA particles resulted in reduced dry sliding wear rates examined up to 80 N load compared with aluminum. Hence, such composites having lower cost could be applied as significantly hard, wear-resistant materials in applications in the automotive industry.

  3. Method for fractional solid-waste sampling and chemical analysis

    DEFF Research Database (Denmark)

    Riber, Christian; Rodushkin, I.; Spliid, Henrik

    2007-01-01

    four subsampling methods and five digestion methods, paying attention to the heterogeneity and the material characteristics of the waste fractions, it was possible to determine 61 substances with low detection limits, reasonable variance, and high accuracy. For most of the substances of environmental...... of variance (20-85% of the overall variation). Only by increasing the sample size significantly can this variance be reduced. The accuracy and short-term reproducibility of the chemical characterization were good, as determined by the analysis of several relevant certified reference materials. Typically, six...... to eight different certified reference materials representing a range of concentrations levels and matrix characteristics were included. Based on the documentation provided, the methods introduced were considered satisfactory for characterization of the chemical composition of waste-material fractions...

  4. State waste discharge permit application, 200-E chemical drain field

    International Nuclear Information System (INIS)

    1994-06-01

    As part of the Hanford Federal Facility Agreement and Consent Order negotiations (Ecology et al. 1994), the US Department of Energy, Richland Operations Office, the US Environmental Protection Agency, and the Washington State Department of Ecology agreed that liquid effluent discharges to the ground on the Hanford Site which affect groundwater or have the potential to affect ground would be subject to permitting under the structure of Chapter 173-216 (or 173-218 where applicable) of the Washington Administrative Code, the State Waste Discharge Permit Program. As a result of this decision, the Washington State Department of Ecology and the US Department of Energy, Richland Operations Office entered into Consent Order No. DE 91NM-177, (Ecology and DOE-RL 1991). The Consent Order No. DE 91NM-177 requires a series of permitting activities for liquid effluent discharges. This document presents the State Waste Discharge Permit (SWDP) application for the 200-E Chemical Drain Field. Waste water from the 272-E Building enters the process sewer line directly through a floor drain, while waste water from the 2703-E Building is collected in two floor drains, (north and south) that act as sumps and are discharged periodically. The 272-E and 2703-E Buildings constitute the only discharges to the process sewer line and the 200-E Chemical Drain Field

  5. State waste discharge permit application, 200-E chemical drain field

    Energy Technology Data Exchange (ETDEWEB)

    1994-06-01

    As part of the Hanford Federal Facility Agreement and Consent Order negotiations (Ecology et al. 1994), the US Department of Energy, Richland Operations Office, the US Environmental Protection Agency, and the Washington State Department of Ecology agreed that liquid effluent discharges to the ground on the Hanford Site which affect groundwater or have the potential to affect ground would be subject to permitting under the structure of Chapter 173-216 (or 173-218 where applicable) of the Washington Administrative Code, the State Waste Discharge Permit Program. As a result of this decision, the Washington State Department of Ecology and the US Department of Energy, Richland Operations Office entered into Consent Order No. DE 91NM-177, (Ecology and DOE-RL 1991). The Consent Order No. DE 91NM-177 requires a series of permitting activities for liquid effluent discharges. This document presents the State Waste Discharge Permit (SWDP) application for the 200-E Chemical Drain Field. Waste water from the 272-E Building enters the process sewer line directly through a floor drain, while waste water from the 2703-E Building is collected in two floor drains, (north and south) that act as sumps and are discharged periodically. The 272-E and 2703-E Buildings constitute the only discharges to the process sewer line and the 200-E Chemical Drain Field.

  6. Session 1984-85. Radioactive waste. Minutes of evidence, Monday 17 June 1985. Nuclear Industry Radioactive Waste Executive

    International Nuclear Information System (INIS)

    1985-01-01

    The Environment Select Committee of the House of Commons received a memorandum from the Nuclear Industry Radioactive Waste Executive, on the management and disposal of radioactive waste arising in the UK, under the headings: introduction; the structure of NIREX; the nature of radioactive waste; plans for the disposal of low and intermediate level wastes. Representatives of NIREX were examined on the subject of the memorandum and the minutes of evidence are recorded. (U.K.)

  7. Definition and manufacture of vitreous matrices using innovative processes for the confinement of nuclear wastes or industrial toxic wastes

    International Nuclear Information System (INIS)

    Boen, R.; Ladirat, C.; Lacombe, J.

    1997-01-01

    Vitrification appears as a solution to toxic mineral waste confinement; this solution has been demonstrated at an industrial level for radioactive wastes. The utilization of cold crucible direct induction melting furnaces, associated to various waste pre-treatments and well-adapted gas processing, leads to the confinement of numerous toxic mineral wastes in a borosilicate vitreous matrix which quality and long term behaviour may be precisely defined

  8. Production waste analysis using value stream mapping and waste assessment model in a handwritten batik industry

    Directory of Open Access Journals (Sweden)

    Marifa Putri Citra

    2018-01-01

    Full Text Available Batik is one of Indonesian cultural heritage that confirmed by United Nations of Educational, Scientific, and Cultural Organization (UNESCO on October 2009. This legal confirmation improves the number of batik industry from many regions based its local unique characteristic. The increasing number of batik SMEs in Indonesia requires a strategy that can create competitive advantage. This strategy can be done by reducing production waste. One of Indonesian batik SMEs is SME Batik CM located in Yogyakarta. There are several problems that occur in the industry, i.e. length of the production process, spots on Batik and excessive raw materials inventory. Based on that problems, this research is done by applying lean manufacturing concept using value stream mapping (VSM method to evaluate production wastes. Based on the result of the research, there are seven types of production waste: overproduction (9,62%, inventory (17,3%, defect (23,08%, motion (9,62%, transportation (9,62%, Over processing (9,62% and waiting (21,15%. Process improvement is done to reduce the highest waste, defect, using quality filter mapping (QFM.

  9. Application of Sorbents for Industrial Waste Water Purification

    Czech Academy of Sciences Publication Activity Database

    Matějková, Martina; Soukup, Karel; Kaštánek, František; Čapek, P.; Grabowski, J.; Stanczyk, K.; Šolcová, Olga

    2015-01-01

    Roč. 38, č. 4 (2015), s. 667-674 ISSN 0930-7516 R&D Projects: GA ČR(CZ) GAP204/11/1206 Grant - others:RFCS(XE) RFCR-CT-2011-00002 Institutional support: RVO:67985858 Keywords : pilot sorption experiments * reactive bed * underground coal gasification Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 2.385, year: 2015

  10. Chemical states of molybdenum in radioactive waste glass

    International Nuclear Information System (INIS)

    Ishiguro, Katsuhiko; Kawanishi, Nobuo; Nagaki, Hiroshi; Naito, Aritsune

    1982-01-01

    In order to confirm an expectation that the chemical state of molybdenum in glass reflects the phase separation tendency of the yellow solid from the melt of borosilicate glass, simulated waste glasses were prepared, and ESCA analysis was performed using a commercially available electron spectrometer (PHI550 E) with an excitation source consisting of Mg Kα-ray. The effects of the concentration of Mo and FE 2 O 3 and the melting atmosphere (oxidizing or reducing) in which the samples were prepared on the chemical state of Mo and the solubility of MoO 3 were examined. From the observation of Mo spectra, it was shown that Mo in waste glass had several valencies, e.g., Mo(3), Mo(4), Mo(5) and Mo(6), while Mo in the yellow solid separated from the melts exhibited hexa-valent state, the peak intensity of higher valencies increased relatively with the increase of MoO 3 concentration, but the chemical state of Mo did not change remarkably around the solubility limit of MoO 3 , the melting atmosphere influenced on the Mo state in the waste glass, the peak intensity of Mo(6) increased relatively with the increasing Fe 2 O 3 concentration, and Mo in devitrified glass exhibited hexa-valent state. (Yoshitake, I.)

  11. Method of waste stabilization with dewatered chemically bonded phosphate ceramics

    Science.gov (United States)

    Wagh, Arun; Maloney, Martin D.

    2010-06-29

    A method of stabilizing a waste in a chemically bonded phosphate ceramic (CBPC). The method consists of preparing a slurry including the waste, water, an oxide binder, and a phosphate binder. The slurry is then allowed to cure to a solid, hydrated CBPC matrix. Next, bound water within the solid, hydrated CBPC matrix is removed. Typically, the bound water is removed by applying heat to the cured CBPC matrix. Preferably, the quantity of heat applied to the cured CBPC matrix is sufficient to drive off water bound within the hydrated CBPC matrix, but not to volatalize other non-water components of the matrix, such as metals and radioactive components. Typically, a temperature range of between 100.degree. C.-200.degree. C. will be sufficient. In another embodiment of the invention wherein the waste and water have been mixed prior to the preparation of the slurry, a select amount of water may be evaporated from the waste and water mixture prior to preparation of the slurry. Another aspect of the invention is a direct anyhydrous CBPC fabrication method wherein water is removed from the slurry by heating and mixing the slurry while allowing the slurry to cure. Additional aspects of the invention are ceramic matrix waste forms prepared by the methods disclosed above.

  12. Rheological properties of kaolin and chemically simulated waste

    International Nuclear Information System (INIS)

    Selby, C.L.

    1981-12-01

    The Savannah River Laboratory is conducting tests to determine the best operating conditions of pumps used to transfer insoluble radioactive sludges from old to new waste tanks. Because it is not feasible to conduct these tests with real or chemically simulated sludges, kaolin clay is being used as a stand-in for the solid waste. The rheology tests described herein were conducted to determine whether the properties of kaolin were sufficiently similar to those of real sludge to permit meaningful pump tests. The rheology study showed that kaolin can be substituted for real waste to accurately determine pump performance. Once adequately sheared, kaolin properties were found to remain constant. Test results determined that kaolin should not be allowed to settle more than two weeks between pump tests. Water or supernate from the waste tanks can be used to dilute sludge on an equal volume basis because they identically affect the rheological properties of sludge. It was further found that the fluid properties of kaolin and waste are insensitive to temperature

  13. Feasibility Studies of Palm Oil Mill Waste Aggregates for the Construction Industry

    Science.gov (United States)

    Kanadasan, Jegathish; Ahmad Fauzi, Auni Filzah; Abdul Razak, Hashim; Selliah, Paramananthan; Subramaniam, Vijaya; Yusoff, Sumiani

    2015-01-01

    The agricultural industry in Malaysia has grown rapidly over the years. Palm oil clinker (POC) is a byproduct obtained from the palm oil industry. Its lightweight properties allows for its utilization as an aggregate, while in powder form as a filler material in concrete. POC specimens obtained throughout each state in Malaysia were investigated to evaluate the physical, chemical, and microstructure characteristics. Variations between each state were determined and their possible contributory factors were assessed. POC were incorporated as a replacement material for aggregates and their engineering characteristics were ascertained. Almost 7% of density was reduced with the introduction of POC as aggregates. A sustainability assessment was made through greenhouse gas emission (GHG) and cost factor analyses to determine the contribution of the addition of POC to the construction industry. Addition of POC helps to lower the GHG emission by 9.6% compared to control specimens. By channeling this waste into the construction industry, an efficient waste-management system can be promoted; thus, creating a cleaner environment. This study is also expected to offer some guides and directions for upcoming research works on the incorporation of POC. PMID:28793579

  14. Feasibility Studies of Palm Oil Mill Waste Aggregates for the Construction Industry.

    Science.gov (United States)

    Kanadasan, Jegathish; Fauzi, Auni Filzah Ahmad; Razak, Hashim Abdul; Selliah, Paramananthan; Subramaniam, Vijaya; Yusoff, Sumiani

    2015-09-22

    The agricultural industry in Malaysia has grown rapidly over the years. Palm oil clinker (POC) is a byproduct obtained from the palm oil industry. Its lightweight properties allows for its utilization as an aggregate, while in powder form as a filler material in concrete. POC specimens obtained throughout each state in Malaysia were investigated to evaluate the physical, chemical, and microstructure characteristics. Variations between each state were determined and their possible contributory factors were assessed. POC were incorporated as a replacement material for aggregates and their engineering characteristics were ascertained. Almost 7% of density was reduced with the introduction of POC as aggregates. A sustainability assessment was made through greenhouse gas emission (GHG) and cost factor analyses to determine the contribution of the addition of POC to the construction industry. Addition of POC helps to lower the GHG emission by 9.6% compared to control specimens. By channeling this waste into the construction industry, an efficient waste-management system can be promoted; thus, creating a cleaner environment. This study is also expected to offer some guides and directions for upcoming research works on the incorporation of POC.

  15. Feasibility Studies of Palm Oil Mill Waste Aggregates for the Construction Industry

    Directory of Open Access Journals (Sweden)

    Jegathish Kanadasan

    2015-09-01

    Full Text Available The agricultural industry in Malaysia has grown rapidly over the years. Palm oil clinker (POC is a byproduct obtained from the palm oil industry. Its lightweight properties allows for its utilization as an aggregate, while in powder form as a filler material in concrete. POC specimens obtained throughout each state in Malaysia were investigated to evaluate the physical, chemical, and microstructure characteristics. Variations between each state were determined and their possible contributory factors were assessed. POC were incorporated as a replacement material for aggregates and their engineering characteristics were ascertained. Almost 7% of density was reduced with the introduction of POC as aggregates. A sustainability assessment was made through greenhouse gas emission (GHG and cost factor analyses to determine the contribution of the addition of POC to the construction industry. Addition of POC helps to lower the GHG emission by 9.6% compared to control specimens. By channeling this waste into the construction industry, an efficient waste-management system can be promoted; thus, creating a cleaner environment. This study is also expected to offer some guides and directions for upcoming research works on the incorporation of POC.

  16. Industrial wastes of the cities of Baku and Sumgait and their effect on green plantings

    Energy Technology Data Exchange (ETDEWEB)

    Amirov, R O; Ismaylov, A R

    1969-01-01

    Baku and Sumgait had large oil production and chemical industries. Investigations showed that injury in green planting depended essentially on the nature of the waste products. Air polluted with SO/sub 2/, chlorine, and fluorine compounds produced dark brown bumps on the leaves. As the distance from the industries increased, the frequency and the intensity of the injuries decreased. Some of the ornamental species were beter adjusted and had a greater resistance. The establishment and development of green plantings were important for combating air pollution and for the sanitary well-being of the industrial area. Plans of landscaping of industrial enterprises included green plantings directly on the territory of the enterprises as well as in areas surrounding them in a radius of 150-500 m. Green shelter belts were needed for protection of the strong northern winds. The selection of plants was made considering their gas resistance, their drought resistance, as well as the plants' ability to grow in solonchak-solonets, clayey, and clayey loam soils characteristic for the Apsheron Peninsula. Trees and bushes were planted by the trench method. Irrigation with waste water was avoided.

  17. Industrial Hazardous Waste Management In Egypt-the baseline study: An Updated review

    International Nuclear Information System (INIS)

    Farida M, S.

    1999-01-01

    Increased industrialization over the past decades in Egypt has resulted in an increased and uncontrolled generation of industrial hazardous waste. This was not accompanied by any concerted efforts to control these wastes. Consequently, no system for handling or disposing of industrial wastes, in general, and industrial hazardous wastes, in specific, exists. In 1993, a baseline report was formulated to assess the overall problem of industrial hazardous waste management in Egypt. Consequently, recommendations for priority actions were identified and the main components of a national hazardous waste system under the provision of Law 4/ 1994 were presented. This paper provides an updated review of this report in light of the proposed technical, legal and institutional guidelines to help in the realization of such a needed waste management system in Egypt

  18. Treatment of Municipal and Industrial Waste by Radiation Processing

    International Nuclear Information System (INIS)

    Abdelaziz, M.E.

    1999-01-01

    In recent years the effort in science and technology is shifting from conventional technologies preventing the pollution of air, water and soil, towards processing by gamma or by electron beam (EB) irradiation in order to prevent pollution, rather than curing the problems caused by production processes, which are not optimized with regard to pollution control. Radiation processing may help to improve the environmental situation in two aspects : It provides alternatives to conventional technologies for the cleaning of air, flue gases and water,...etc, and it also helps to realize clean processes for preventing pollution in the first place. This paper will outline the basic principles of radiation processing for waste streams of environmental relevance, will summarize the state-of -the-art in environmental applications of radiation processing to show both the advantages and the limitations of the radiation processing of waste streams, and to highlight the environmental and economic benefits of clean processes made possible by radiation processing applied to municipal and industrial waste. Reference is made to gamma and EB radiation sources, and description of new technologies is presented

  19. An Industrial Ecology Approach to Municipal Solid Waste ...

    Science.gov (United States)

    The organic fraction of municipal solid waste provides abundant opportunities for industrial ecology-based symbiotic use. Energy production, economics, and environmental aspects are analyzed for four alternatives based on different technologies: incineration with energy recovery, gasification, anaerobic digestion, and fermentation. In these cases electricity and ethanol are the products considered, but other products and attempts at symbiosis can be made. The four technologies are in various states of commercial development. To highlight their relative complexities some adjustable parameters which are important for the operability of each process are discussed. While these technologies need to be considered for specific locations and circumstances, generalized economic and environmental information suggests relative comparisons for newly conceptualized processes. The results of industrial ecology-based analysis suggest that anaerobic digestion may improve seven emission categories, while fermentation, gasification, and incineration successively improve fewer emissions. A conceptual level analysis indicates that gasification, anaerobic digestion, and fermentation alternatives lead to positive economic results. In each case the alternatives and their assumptions need further analysis for any particular community. Presents information useful for analyzing the sustainability of alternatives for the management of municipal solid waste.

  20. Comparison of soil heavy metal pollution caused by e-waste recycling activities and traditional industrial operations.

    Science.gov (United States)

    He, Kailing; Sun, Zehang; Hu, Yuanan; Zeng, Xiangying; Yu, Zhiqiang; Cheng, Hefa

    2017-04-01

    The traditional industrial operations are well recognized as an important source of heavy metal pollution, while that caused by the e-waste recycling activities, which have sprouted in some developing countries, is often overlooked. This study was carried out to compare the status of soil heavy metal pollution caused by the traditional industrial operations and the e-waste recycling activities in the Pearl River Delta, and assess whether greater attention should be paid to control the pollution arising from e-waste recycling activities. Both the total contents and the chemical fractionation of major heavy metals (As, Cr, Cd, Ni, Pb, Cu, and Zn) in 50 surface soil samples collected from the e-waste recycling areas and 20 soil samples from the traditional industrial zones were determined. The results show that the soils in the e-waste recycling areas were mainly polluted by Cu, Zn, As, and Cd, while Cu, Zn, As, Cd, and Pb were the major heavy metals in the soils from the traditional industrial zones. Statistical analyses consistently show that Cu, Cd, Pb, and Zn in the surface soils from both types of sites were contributed mostly by human activities, while As, Cr, and Ni in the soils were dominated by natural background. No clear distinction was found on the pollution characteristic of heavy metals in the surface soils between the e-waste recycling areas and traditional industrial zones. The potential ecological risk posed by heavy metals in the surface soils from both types of sites, which was dominated by that from Cd, ranged from low to moderate. Given the much shorter development history of e-waste recycling and its largely unregulated nature, significant efforts should be made to crack down on illegal e-waste recycling and strengthen pollution control for related activities.

  1. Applications of thermal energy storage to waste heat recovery in the food processing industry

    Science.gov (United States)

    Wojnar, F.; Lunberg, W. L.

    1980-01-01

    A study to assess the potential for waste heat recovery in the food industry and to evaluate prospective waste heat recovery system concepts employing thermal energy storage was conducted. The study found that the recovery of waste heat in canning facilities can be performed in significant quantities using systems involving thermal energy storage that are both practical and economical. A demonstration project is proposed to determine actual waste heat recovery costs and benefits and to encourage system implementation by the food industry.

  2. Growth and metal bioconcentration by conspecific freshwater macroalgae cultured in industrial waste water

    OpenAIRE

    Michael B. Ellison; Rocky de Nys; Nicholas A. Paul; David A. Roberts

    2014-01-01

    The bioremediation of industrial waste water by macroalgae is a sustainable and renewable approach to the treatment of waste water produced by multiple industries. However, few studies have tested the bioremediation of complex multi-element waste streams from coal-fired power stations by live algae. This study compares the ability of three species of green freshwater macroalgae from the genus Oedogonium, isolated from different geographic regions, to grow in waste water for the bioremediation...

  3. Guidelines for generators of hazardous chemical waste at LBL and guidelines for generators of radioactive and mixed waste at LBL

    International Nuclear Information System (INIS)

    1991-09-01

    In part one of this document the Governing Documents and Definitions sections provide general guidelines and regulations applying to the handling of hazardous chemical wastes. The remaining sections provide details on how you can prepare your waste properly for transport and disposal. They are correlated with the steps you must take to properly prepare your waste for pickup. The purpose of the second part of this document is to provide the acceptance criteria for the transfer of radioactive and mixed waste to LBL's Hazardous Waste Handling Facility (HWHF). These guidelines describe how you, as a generator of radioactive or mixed waste, can meet LBL's acceptance criteria for radioactive and mixed waste

  4. CO2 emissions and reduction potential in China's chemical industry

    International Nuclear Information System (INIS)

    Zhu, Bing; Zhou, Wenji; Hu, Shanying; Li, Qiang; Griffy-Brown, Charla; Jin, Yong

    2010-01-01

    GHG (Increasing greenhouse gas) emissions in China imposes enormous pressure on China's government and society. The increasing GHG trend is primarily driven by the fast expansion of high energy-intensive sectors including the chemical industry. This study investigates energy consumption and CO 2 emissions in the processes of chemical production in China through calculating the amounts of CO 2 emissions and estimating the reduction potential in the near future. The research is based on a two-level perspective which treats the entire industry as Level one and six key sub-sectors as Level two, including coal-based ammonia, calcium carbide, caustic soda, coal-based methanol, sodium carbonate, and yellow phosphorus. These two levels are used in order to address the complexity caused by the fact that there are more than 40 thousand chemical products in this industry and the performance levels of the technologies employed are extremely uneven. Three scenarios with different technological improvements are defined to estimate the emissions of the six sub-sectors and analyze the implied reduction potential in the near future. The results highlight the pivotal role that regulation and policy administration could play in controlling the CO 2 emissions by promoting average technology performances in this industry.

  5. Enhanced formulations for neutralization of chemical, biological and industrial toxants

    Science.gov (United States)

    Tucker, Mark D [Albuqueque, NM

    2008-06-24

    An enhanced formulation and method of making that neutralizes the adverse health effects of both chemical and biological compounds, especially chemical warfare (CW) and biological warfare (BW) agents, and toxic industrial chemicals. The enhanced formulation according to the present invention is non-toxic and non-corrosive and can be delivered by a variety of means and in different phases. The formulation provides solubilizing compounds that serve to effectively render the chemical and biological compounds, particularly CW and BW compounds, susceptible to attack, and at least one reactive compound that serves to attack (and detoxify or kill) the compound. The formulation includes at least one solubilizing agent, a reactive compound, a bleaching activator and water.

  6. Radon effective dose from TENORM waste associated with petroleum industries

    International Nuclear Information System (INIS)

    Abo-Elmagd, M.; Soliman, H. A.; Daif, M. M.

    2009-01-01

    Technically enhanced naturally occurring radioactive material (TENORM) associated with petroleum industries can be accumulated with elevated quantities and therefore can threat the workers through external and internal exposure. Measurements of radon-related parameters give information about the radioactivity levels in the TENORM waste using the well-established correlation. Also, it is useful to calculate the internal exposure due to radon inhalation in terms of effective radon dose. Among radon-related parameters, areal exhalation rate is the most suitable for characterising land and objects with only upper surface contamination in the case of petroleum waste. The TENORM in this study is collected from waste storage areas located near oil fields at south Sinai governorate (Egypt). The average values of exhalation rates as measured by Lucas cell based on delay count method are 273 ± 144 and 38 ± 8 Bq m -2 h -1 for scale and sludge, respectively. Whereas, two count method gives results with 18 and 20 % lower values for scale and sludge, respectively with good correlation coefficient of 0.999 and 0.852, respectively. Sealed cup fitted with CR-39 gives results compatible with Lucas cell with minor deviation in case of scale due to its thoron content. The results of CR-39 are qualified by taking into consideration the correction for back diffusion effect. The effective radon dose was calculated for different simulated radioactive waste storage areas with different contaminated areas and air ventilation rate. Minimising the contaminated areas and building up efficient ventilation systems can reduce the internal exposure even in the case of RWSA-containing TENORM with elevated radioactivity. (authors)

  7. Low-temperature catalytic gasification of wet industrial wastes

    Energy Technology Data Exchange (ETDEWEB)

    Elliott, D C; Neuenschwander, G G; Baker, E G; Sealock, Jr, L J; Butner, R S

    1991-04-01

    Bench-scale reactor tests are in progress at Pacific Northwest Laboratory to develop a low-temperature, catalytic gasification system. The system, licensed under the trade name Thermochemical Environmental Energy System (TEES{reg sign}), is designed for treating a wide variety of feedstocks ranging from dilute organics in water to waste sludges from food processing. This report describes a test program which used a continuous-feed tubular reactor. This test program is an intermediate stage in the process development. The reactor is a laboratory-scale version of the commercial concept as currently envisioned by the process developers. An energy benefit and economic analysis was also completed on the process. Four conceptual commercial installations of the TEES process were evaluated for three food processing applications and one organic chemical manufacturing application. Net energy production (medium-Btu gas) was achieved in all four cases. The organic chemical application was found to be economically attractive in the present situation. Based on sensitivity studies included in the analysis, the three food processing cases will likely become attractive in the near future as waste disposal regulations tighten and disposal costs increase. 21 refs., 2 figs., 9 tabs.

  8. Elimination of micropollutants and hazardous substances at the source in the chemical and pharmaceutical industry.

    Science.gov (United States)

    Blöcher, C

    2007-01-01

    Industrial wastewater, especially from chemical and pharmaceutical production, often contains substances that need to be eliminated before being discharged into a biological treatment plant and following water bodies. This can be done within the production itself, in selected waste water streams or in a central treatment plant. Each of these approaches has certain advantages and disadvantages. Furthermore, a variety of wastewater treatment processes exist that can be applied at each stage, making it a challenging task to choose the best one in economic and ecological terms. In this work a general approach for that and examples from practice are discussed.

  9. Industrial waste management within manufacturing: a comparative study of tools, policies, visions and concepts

    OpenAIRE

    Shahbazi, Sasha; Kurdve, Martin; Bjelkemyr, Marcus; Jönsson, Christina; Wiktorsson, Magnus

    2013-01-01

    Industrial waste is a key factor when assessing the sustainability of a manufacturing process or company. A multitude of visions, concepts, tools, and policies are used both academically and industrially to improve the environmental effect of manufacturing; a majority of these approaches have a direct bearing on industrial waste. The identified approaches have in this paper been categorised according to application area, goals, organisational entity, life cycle phase, and waste hierarchy stag...

  10. Screening values for Non-Carcinogenic Hanford Waste Tank Vapor Chemicals that Lack Established Occupational Exposure Limits

    Energy Technology Data Exchange (ETDEWEB)

    Poet, Torka S.; Mast, Terryl J.; Huckaby, James L.

    2006-02-06

    Over 1,500 different volatile chemicals have been reported in the headspaces of tanks used to store high-level radioactive waste at the U.S. Department of Energy's Hanford Site. Concern about potential exposure of tank farm workers to these chemicals has prompted efforts to evaluate their toxicity, identify chemicals that pose the greatest risk, and incorporate that information into the tank farms industrial hygiene worker protection program. Established occupation exposure limits for individual chemicals and petroleum hydrocarbon mixtures have been used elsewhere to evaluate about 900 of the chemicals. In this report headspace concentration screening values were established for the remaining 600 chemicals using available industrial hygiene and toxicological data. Screening values were intended to be more than an order of magnitude below concentrations that may cause adverse health effects in workers, assuming a 40-hour/week occupational exposure. Screening values were compared to the maximum reported headspace concentrations.

  11. Chemical tailoring of steam to remediate underground mixed waste contaminents

    Science.gov (United States)

    Aines, Roger D.; Udell, Kent S.; Bruton, Carol J.; Carrigan, Charles R.

    1999-01-01

    A method to simultaneously remediate mixed-waste underground contamination, such as organic liquids, metals, and radionuclides involves chemical tailoring of steam for underground injection. Gases or chemicals are injected into a high pressure steam flow being injected via one or more injection wells to contaminated soil located beyond a depth where excavation is possible. The injection of the steam with gases or chemicals mobilizes contaminants, such as metals and organics, as the steam pushes the waste through the ground toward an extraction well having subatmospheric pressure (vacuum). The steam and mobilized contaminants are drawn in a substantially horizontal direction to the extraction well and withdrawn to a treatment point above ground. The heat and boiling action of the front of the steam flow enhance the mobilizing effects of the chemical or gas additives. The method may also be utilized for immobilization of metals by using an additive in the steam which causes precipitation of the metals into clusters large enough to limit their future migration, while removing any organic contaminants.

  12. Bentonite chemical modification for use in industrial effluents

    International Nuclear Information System (INIS)

    Laranjeira, E.; Pinto, M.R.O.; Rodrigues, D.P.; Costa, B.P.; Guimaraes, P.L.F.

    2010-01-01

    The present work aims at synthesizing organoclays using a layered silicate of regional importance, bentonite clay, for the treatment of industrial effluents. The choice of clay to be organophilized was based on cation exchange capacity (CEC). Bentonite with higher CTC was called AN 35 (92 meq/100 g), and therefore was the one that suffered the chemical modification with salt cetyl trimethyl ammonium Cetremide, provided by Vetec.The unmodified and modified clays were characterized by FTIR and XDR. The data obtained through the characterizations confirmed the acquisition of bentonite organoclay thus suggesting its subsequent application in the treatment of industrial effluents. (author)

  13. Implementation of high-dose chemical dosimetry for industrial facilities

    International Nuclear Information System (INIS)

    Conceicao, Cirilo Cezar Sant'Anna da

    2006-01-01

    The purpose of this work is the implementation of methodology for high dose measurements using chemical dosimeters in liquid phase, traceable to the international metrology system, and make available in the country, the standard of high-dose to industrial irradiation facilities and research irradiators, trough the quality program with comparative measurements and direct use of the standard dosimeters in routine. The use of these low cost dosimetry systems in industrial irradiation facilities, assists to the certification requirements and it can reduce the costs with dosimetry for approximately 20% of the total dosimetry costs, using these systems in routine measurements and validation process, largely substituting the imported PMMA dosimeters, among others. (author)

  14. A new material for chemical industry - wood polymer composites

    International Nuclear Information System (INIS)

    Majali, A.B.; Patil, N.D.

    1979-01-01

    The paper outlines the advantages of the radiation cured wood-polymer composites (WPC) for application in certain critical areas of chemical industry. The wood-polymer composite made filterpress frames and plates were tested in a chemical plant. The entire exercise is elaborated. The radiation cured wood exhibited a considerably extended useful life in alkaline and acidic solutions. Composites based on teak wood showed a remarkable improvement with a nominal polymer loading of 10%. The reports of accelerated aging test of WPC are also presented. (auth.)

  15. Decree 182/013 It would regulate the management of industrial solid waste and similar expenses

    International Nuclear Information System (INIS)

    2013-01-01

    It regulate of industrial solid waste management and similar expenses activities covered, exclusions, categorization, requirements, transportation, recycling and treatment, incineration, use as alternative fuel

  16. Economical solution for the industrial waste problem of Karachi industrial area

    International Nuclear Information System (INIS)

    Mubin, S.

    2005-01-01

    The increased rate of industrialization coupled with rapid urbanization in Pakistan has given rise to serious water pollution and environmental problems. A vast range of industries has been established in the country during the last twenty five years, including tanneries, fertilizers, textiles, refineries, chemicals, vegetable oils, paper am pulp, sugar and food. Little attention was paid towards a large scale release of wastewater from these industries. Presently wastewater produced from these industries has been considered a serious problem and research in being conducted to solve its associated problems. Recently, it has been realized that there is a significant threat of water borne diseases, degradation of fresh water quality, environmental depletion and soil deterioration from the effluent and toxic emission of industries. Being a developing country and having limited resources, it is hard to install treatment plants on the industrial effluent with every industry before discharging them into streams which are also creating disturbance in natural ecosystem. An effort has been made to solve wastewater problem by implementing statistical tools on data of Karachi industrial state, obtained from EPA JICA and PCRWR, Islamabad. (author)

  17. Waste water biological purification plants of dairy products industry and energy management

    Science.gov (United States)

    Stepanov, Sergey; Solkina, Olga; Stepanov, Alexander; Zhukova, Maria

    2017-10-01

    The paper presents results of engineering and economical comparison of waste water biological purification plants of dairy products industry. Three methods of purification are compared: traditional biological purification with the use of secondary clarifiers and afterpurification through granular-bed filters, biomembrane technology and physical-and-chemical treatment together with biomembrane technology for new construction conditions. The improvement of the biological purification technology using nitro-denitrification and membrane un-mixing of sludge mixture is a promising trend in this area. In these calculations, an energy management which is widely applied abroad was used. The descriptions of the three methods are illustrated with structural schemes. Costs of equipment and production areas are taken from manufacturers’ data. The research is aimed at an engineering and economical comparison of new constructions of waste water purification of dairy products industry. The experiment demonstrates advantages of biomembrane technology in waste water purification. This technology offers prospects of 122 million rubles cost saving during 25 years of operation when compared with of the technology of preparatory reagent flotation and of 13.7 million rubles cost saving compared to the option of traditional biological purification.

  18. Radiological, physical, and chemical characterization of transuranic wastes stored at the Idaho National Engineering Laboratory

    International Nuclear Information System (INIS)

    Apel, M.L.; Becker, G.K.; Ragan, Z.K.; Frasure, J.; Raivo, B.D.; Gale, L.G.; Pace, D.P.

    1994-03-01

    This document provides radiological, physical and chemical characterization data for transuranic radioactive wastes and transuranic radioactive and hazardous (i.e., mixed) wastes stored at the Idaho National Engineering Laboratory and considered for treatment under the Private Sector Participation Initiative Program (PSPI). Waste characterization data are provided in the form of INEL Waste Profile Sheets. These documents provide, for each content code, information on waste identification, waste description, waste storage configuration, physical/chemical waste composition, radionuclide and associated alpha activity waste characterization data, and hazardous constituents present in the waste. Information is provided for 139 waste streams which represent an estimated total volume of 39,380 3 corresponding to a total mass of approximately 19,000,000 kg. In addition, considerable information concerning alpha, beta, gamma, and neutron source term data specific to Rocky Flats Plant generated waste forms stored at the INEL are provided to assist in facility design specification

  19. Chemical Recycling of PET Wastes with Different Catalysts

    Directory of Open Access Journals (Sweden)

    Mohammad Khoonkari

    2015-01-01

    Full Text Available Chemical recycling of polyethylene terephthalate, known as PET, has been the subject of increased interest as a valuable feedstock for different chemical processes. In this work, glycolysis of PET waste granules was carried out using excess ethylene glycol in the presence of different simple chemicals acting as catalysts, which are, namely, categorized in ionic liquids, metal salts, hydrotalcites, and enzymes. From every category, some materials as a sample were used, and the one which is going to bring the best result is noted. The effect of some parameters such as temperature, pressure, amount of sample, material ratio, and stirring rate was investigated. As a result we compared the best of each category with the others and final result is shown.

  20. Probabilistic safety assessment in the chemical and nuclear industries

    CERN Document Server

    Fullwood, Ralph R

    2000-01-01

    Probabilistic Safety Analysis (PSA) determines the probability and consequences of accidents, hence, the risk. This subject concerns policy makers, regulators, designers, educators and engineers working to achieve maximum safety with operational efficiency. Risk is analyzed using methods for achieving reliability in the space program. The first major application was to the nuclear power industry, followed by applications to the chemical industry. It has also been applied to space, aviation, defense, ground, and water transportation. This book is unique in its treatment of chemical and nuclear risk. Problems are included at the end of many chapters, and answers are in the back of the book. Computer files are provided (via the internet), containing reliability data, a calculator that determines failure rate and uncertainty based on field experience, pipe break calculator, event tree calculator, FTAP and associated programs for fault tree analysis, and a units conversion code. It contains 540 references and many...

  1. Content of nitrogen in waste petroleum carbon for steel industries

    International Nuclear Information System (INIS)

    Rios, R.O; Jimenez, A.F; Szieber, C.W; Banchik, A.D

    2004-01-01

    Steel industries use refined carbon as an alloy for steel production. This alloy is produced from waste carbon from the distillation of the petroleum. The refined carbon, called recarburizer, is obtained by calcination at high temperature. Under these thermal conditions the organic molecules decompose and a fraction of the N 2 , S and H 2 , volatile material and moisture are released; while the carbon tends to develop a crystalline structure similar to graphite's. The right combination of calcinations temperature and time in the furnace can optimize the quality of the resulting product. The content of S and N 2 has to be minimized for the use of calcined carbon in the steel industry. Nitrogen content should be reduced by two orders of magnitude, from 1% - 2% down to hundreds of ppm by weight. This work describes the activities undertaken to obtain calcined coke from petroleum from crude oil carbon that satisfies the requirements of the Mercosur standard 02:00-169 (Pending) for use as a carborizer in steels industries. To satisfy the requirements of the Mercosur standards NM 236:00 IRAM-IAS-NM so that graphite is used as a carburizer a content of 300 ppm maximum weight of nitrogen has to be obtained. So the first stage in this development is to define a production process for supplying calcined coke in the range of nitrogen concentrations required by the Mercosur standards (CW)

  2. Utilization of the waste products from the forest industry as raw materials for the production. [In Swedish

    Energy Technology Data Exchange (ETDEWEB)

    Kringstad, K

    1977-02-01

    The economic and marketing possibilitiesof industrial production of chemicals and/or proteins by utilizing waste liquor from processes at pulp mills or bark and needles was investigated. A survey of known processes for such production is given. The costs of producing several chemicals and proteins were estimated and compared with costs of producing these products via petrochemistry. The present as well as the future market of the different chemicals and of proteins were estimated. The present investigation was performed due to the rapidly increasing oil prices.

  3. Intensifying waste water clarification in heavy and mining industries for sanitation of rivers in the Katowice district

    Energy Technology Data Exchange (ETDEWEB)

    Paluch, J.; Twardowska, I.

    1976-01-01

    This article presents a detailed account of the state of water pollution in the main and tributary rivers of the heavily populated and industrialized district of Katowice, Poland: Results of surveys in the years 1969 to 1972 are given. Several tables and maps show the degree of water pollution in rivers, the amount to which the values exceed pollution standards, percentage of treated and untreated industrial waste water entering the rivers, the classification of river sections according to their content of suspensions, phenols and salt. Further figures show the effectiveness of water cleaning flocculating agents and of waste water treatment at coking plants. Black coal mining and processing contributes the greater part to pollution of the rivers. Only 54% of mining industry waste water is cleaned mechanically and 3% chemically. The amount of 3,300 t/d of chlorite and sulfate salts is led into the rivers primarily from the Rybnik coal mining area. The clarification of waste water resulting from hydraulic stowing and from flotation processes is described as most problematic. Research efforts are being made at economic desalination and suspension flocculation. In the coking industry waste water is treated in 88% of the plants, but dephenolization takes place in only 50% of the plants. (29 refs.) (In German)

  4. Chemical engineering problems of radioactive waste fixation by vitrification

    International Nuclear Information System (INIS)

    Taylor, R.F.

    1985-01-01

    Basic features are reviewed of the chemical engineering problems faced in the vitrification of the high-level radioactive liquid wastes resulting from the reprocessing of nuclear fuel. After an outline of glass solution properties and formation kinetics the constituent elements of the vitrification route are examined in turn: waste feed evaporation and denitration, calcination, offgas treatment, and finally melting and product quality. Plant and experimental data for each stage are discussed with comparison between process routes and with reference to the underlying principles. Attention is drawn to the future need for higher trapping efficiencies and for dealing with a wider range of species in offgas treatments as higher burnup fuels are processed after shorter cooling times from reactor. Two areas of present study where deeper insight into underlying process mechanics is needed are, firstly, the association of waste material with glass formers in the wet or sinter stages and secondly their incorporation and mixing reaction in the melt. Fuller understanding here would bring direct benefit to process performance and handling. The problems discussed are not of a nature to jeopardize the vitrification routes but if product quality does come to rely heavily on process control then demonstrable confidence in the behaviour of the central physico-chemical interactions is indispensable. (author)

  5. Conversion of wastes into bioelectricity and chemicals by using microbial electrochemical technologies.

    Science.gov (United States)

    Logan, Bruce E; Rabaey, Korneel

    2012-08-10

    Waste biomass is a cheap and relatively abundant source of electrons for microbes capable of producing electrical current outside the cell. Rapidly developing microbial electrochemical technologies, such as microbial fuel cells, are part of a diverse platform of future sustainable energy and chemical production technologies. We review the key advances that will enable the use of exoelectrogenic microorganisms to generate biofuels, hydrogen gas, methane, and other valuable inorganic and organic chemicals. Moreover, we examine the key challenges for implementing these systems and compare them to similar renewable energy technologies. Although commercial development is already underway in several different applications, ranging from wastewater treatment to industrial chemical production, further research is needed regarding efficiency, scalability, system lifetimes, and reliability.

  6. Conversion of Wastes into Bioelectricity and Chemicals by Using Microbial Electrochemical Technologies

    KAUST Repository

    Logan, B. E.

    2012-08-09

    Waste biomass is a cheap and relatively abundant source of electrons for microbes capable of producing electrical current outside the cell. Rapidly developing microbial electrochemical technologies, such as microbial fuel cells, are part of a diverse platform of future sustainable energy and chemical production technologies. We review the key advances that will enable the use of exoelectrogenic microorganisms to generate biofuels, hydrogen gas, methane, and other valuable inorganic and organic chemicals. Moreover, we examine the key challenges for implementing these systems and compare them to similar renewable energy technologies. Although commercial development is already underway in several different applications, ranging from wastewater treatment to industrial chemical production, further research is needed regarding efficiency, scalability, system lifetimes, and reliability.

  7. Reactive formulations for a neutralization of toxic industrial chemicals

    Science.gov (United States)

    Tucker, Mark D [Albuqueruqe, NM; Betty, Rita G [Rio Rancho, NM

    2006-10-24

    Decontamination formulations for neutralization of toxic industrial chemicals, and methods of making and using same. The formulations are effective for neutralizing malathion, hydrogen cyanide, sodium cyanide, butyl isocyanate, carbon disulfide, phosgene gas, capsaicin in commercial pepper spray, chlorine gas, anhydrous ammonia gas; and may be effective at neutralizing hydrogen sulfide, sulfur dioxide, formaldehyde, ethylene oxide, methyl bromide, boron trichloride, fluorine, tetraethyl pyrophosphate, phosphorous trichloride, arsine, and tungsten hexafluoride.

  8. An evaluation of alternative technologies for the management of industrial wastes at Nalluk Base, Tuktoyaktuk, Northwest Territories

    Energy Technology Data Exchange (ETDEWEB)

    MacDonald, A.R.

    1993-05-01

    A study was carried out to identify and evaluate alternative waste treatment and/or disposal technologies that would be effective in improving the management of slops, used glycol and industrial solid wastes at Nalluk Base, Tuktoyaktuk, Northwest Territories. This site was used as a base for an offshore oil and gas drilling program between 1983 and 1992. Background research was conducted to review the biophysical, regulatory and socioeconomic conditions which have had an influence on Nalluk Base waste management operations. Concerns in relation to management of industrial wastes at the base include: extreme climate, permafrost geology, remote location, excessive government regulations but no specific legislation, and distrust of white man by local Inuvialuit. The five major waste streams handled at the base (used glycol, oily slops, scrap metal, used containers and ash) were characterized in terms of physical and chemical characteristics, anticipated volumes, and potential contaminants. Eighty-six waste treatment and disposal processes were reviewed for their applicability in treating each of the five waste streams. Short-listed options were subjected to full-cost environmental accounting. Preferred options identified were: used glycol, one site reuse using vacuum distillation; unseparated slops and used oil/fuel, off-site cement kiln incineration; oily wastewater, on-site evaporation; sludge, offsite landfill; scrap metal and used containers, Hamlet landfill (current practise); and ash, off-site landfill. 178 refs., 15 figs., 34 tabs.

  9. Applications of chemical sensors in spent fuel reprocessing and waste management

    International Nuclear Information System (INIS)

    Achuthan, P.V.

    2012-01-01

    Environmental friendly power generation is essential to preserve the quality of life for the future generations. For more than fifty years, nuclear energy has proven its potential as an economically and commercially viable alternative to conventional energy. More over it is a clean source of energy with minimum green house effect. Recent data on climate changes have stressed the need for more caution on atmospheric discharges, hence a revival of interest in nuclear energy is in the offing. The entire world is committed to protect the atmosphere from polluting agents. Even nuclear power plants and the fuel cycle facilities are looking forward to reduce the already low gaseous emissions further and also to develop ways and means of controlling the impact of the small but significant radiotoxicity of the wastes generated in the nuclear fuel cycle. Spent fuel reprocessing and associated waste management, an integral part of the nuclear fuel cycle, employs chemical processes for the recovery of fuel value and for the conditioning of the reprocessed waste. In this respect they can be classified as a chemical plant dealing with radioactive materials. Hence it is essential to keep the gaseous, liquid and solid discharges at the lowest possible levels to comply with the regulations of discharges stipulated by the regulatory authorities. Elaborate cleaning and detection systems are needed for effective control of these discharges from both radioactive and chemical contamination point of view. Even though radiation detectors, which are non specific to the analytes, are the major tools for these controls, analyte specific chemical sensors can play a vital role in controlling the chemical vapours/gases generated during processing. The presentation will cover the major areas where chemical sensors play a significant role in this industry. (author)

  10. The Use of Chemical Modification of Polymer Waste for Obtaining Polymer Flocculants

    Institute of Scientific and Technical Information of China (English)

    W.W.Sulkowski; K.Nowak; A.Sulkowska; A.Wolin; ska; S.Malanka; W.M.Baldur; D.Pentak

    2007-01-01

    1 Results Chemical modification of polymer plastic wastes to useful products can be one of the way of effective waste plastics management (chemical recycling). Chemical modification of polymers and polymer plastic wastes can yield products with suitable physical and chemical properties. In consequence they can be used as polyelectrolytes[1]. The variety of pollutants, universality of various water and sewage treatment technologies, introduction of new water quality improved technologies have caused a gr...

  11. Pyrochlore as nuclear waste form. Actinide uptake and chemical stability

    Energy Technology Data Exchange (ETDEWEB)

    Finkeldei, Sarah Charlotte

    2015-07-01

    Radioactive waste is generated by many different technical and scientific applications. For the past decades, different waste disposal strategies have been considered. Several questions on the waste disposal strategy remain unanswered, particularly regarding the long-term radiotoxicity of minor actinides (Am, Cm, Np), plutonium and uranium. These radionuclides mainly arise from high level nuclear waste (HLW), specific waste streams or dismantled nuclear weapons. Although many countries have opted for the direct disposal of spent fuel, from a scientific and technical point of view it is imperative to pursue alternative waste management strategies. Apart from the vitrification, especially for trivalent actinides and Pu, crystalline ceramic waste forms are considered. In contrast to glasses, crystalline waste forms, which are chemically and physically highly stable, allow the retention of radionuclides on well-defined lattice positions within the crystal structure. Besides polyphase ceramics such as SYNROC, single phase ceramics are considered as tailor made host phases to embed a specific radionuclide or a specific group. Among oxidic single phase ceramics pyrochlores are known to have a high potential for this application. This work examines ZrO{sub 2} based pyrochlores as potential nuclear waste forms, which are known to show a high aqueous stability and a high tolerance towards radiation damage. This work contributes to (1) understand the phase stability field of pyrochlore and consequences of non-stoichiometry which leads to pyrochlores with mixed cationic sites. Mixed cationic occupancies are likely to occur in actinide-bearing pyrochlores. (2) The structural uptake of radionuclides themselves was studied. (3) The chemical stability and the effect of phase transition from pyrochlore to defect fluorite were probed. This phase transition is important, as it is the result of radiation damage in ZrO{sub 2} based pyrochlores. ZrO{sub 2} - Nd{sub 2}O{sub 3} pellets

  12. Pyrochlore as nuclear waste form. Actinide uptake and chemical stability

    International Nuclear Information System (INIS)

    Finkeldei, Sarah Charlotte

    2015-01-01

    Radioactive waste is generated by many different technical and scientific applications. For the past decades, different waste disposal strategies have been considered. Several questions on the waste disposal strategy remain unanswered, particularly regarding the long-term radiotoxicity of minor actinides (Am, Cm, Np), plutonium and uranium. These radionuclides mainly arise from high level nuclear waste (HLW), specific waste streams or dismantled nuclear weapons. Although many countries have opted for the direct disposal of spent fuel, from a scientific and technical point of view it is imperative to pursue alternative waste management strategies. Apart from the vitrification, especially for trivalent actinides and Pu, crystalline ceramic waste forms are considered. In contrast to glasses, crystalline waste forms, which are chemically and physically highly stable, allow the retention of radionuclides on well-defined lattice positions within the crystal structure. Besides polyphase ceramics such as SYNROC, single phase ceramics are considered as tailor made host phases to embed a specific radionuclide or a specific group. Among oxidic single phase ceramics pyrochlores are known to have a high potential for this application. This work examines ZrO 2 based pyrochlores as potential nuclear waste forms, which are known to show a high aqueous stability and a high tolerance towards radiation damage. This work contributes to (1) understand the phase stability field of pyrochlore and consequences of non-stoichiometry which leads to pyrochlores with mixed cationic sites. Mixed cationic occupancies are likely to occur in actinide-bearing pyrochlores. (2) The structural uptake of radionuclides themselves was studied. (3) The chemical stability and the effect of phase transition from pyrochlore to defect fluorite were probed. This phase transition is important, as it is the result of radiation damage in ZrO 2 based pyrochlores. ZrO 2 - Nd 2 O 3 pellets with pyrochlore and defect

  13. The production of chemicals from food processing wastes using a novel fermenter separator. Annual progress report, January 1993--March 1994

    Energy Technology Data Exchange (ETDEWEB)

    Dale, M.C.; Venkatesh, K.V.; Choi, H.; Salicetti-Piazza, L.; Borgos-Rubio, N.; Okos, M.R.; Wankat, P.C.

    1994-03-15

    The basic objective of this project is to convert waste streams from the food processing industry to usable fuels and chemicals using novel bioreactors. These bioreactors should allow economical utilization of waste (whey, waste sugars, waste starch, bottling wastes, candy wastes, molasses, and cellulosic wastes) by the production of ethanol, acetone/butanol, organic acids (acetic, lactic, and gluconic), yeast diacetyl flavor, and antifungal compounds. Continuous processes incorporating various processing improvements such as simultaneous product separation and immobilized cells are being developed to allow commercial scale utilization of waste stream. The production of ethanol by a continuous reactor-separator is the process closest to commercialization with a 7,500 liter pilot plant presently sited at an Iowa site to convert whey lactose to ethanol. Accomplishments during 1993 include installation and start-up of a 7,500 liter ICRS for ethanol production at an industry site in Iowa; Donation and installation of a 200 liter yeast pilot Plant to the project from Kenyon Enterprises; Modeling and testing of a low energy system for recovery of ethanol from vapor is using a solvent absorption/extractive distillation system; Simultaneous saccharification/fermentation of raw corn grits and starch in a stirred reactor/separator; Testing of the ability of `koji` process to ferment raw corn grits in a `no-cook` process.

  14. Stabilization of low-level mixed waste in chemically bonded phosphate ceramics

    International Nuclear Information System (INIS)

    Wagh, A.S.; Singh, D.; Sarkar, A.V.

    1994-06-01

    Mixed waste streams, which contain both chemical and radioactive wastes, are one of the important categories of DOE waste streams needing stabilization for final disposal. Recent studies have shown that chemically bonded phosphate ceramics may have the potential for stabilizing these waste streams, particularly those containing volatiles and pyrophorics. Such waste streams cannot be stabilized by conventional thermal treatment methods such as vitrification. Phosphate ceramics may be fabricated at room temperature into durable, hard and dense materials. For this reason room-temperature-setting phosphate ceramic waste forms are being developed to stabilize these to ''problem waste streams.''

  15. Bioprocessing applications in the management of nuclear and chemical wastes

    International Nuclear Information System (INIS)

    Genung, R.K.

    1989-01-01

    The US Department of Energy (DOE), the US Department of Defense (DOD), and other federal agencies already face profound challenges in finding strategies that manage budgets and priorities while bringing their sites and facilities into compliance with current statues and regulations and with agency policies and orders. While it is often agreed that current technology can be used to address most waste management and environmental restoration needs, it is also argued by many that the costs of implementing current technology will be too high unless the standards and schedules for compliance are relaxed. Since this is socially unacceptable, efforts to improve the efficiency of existing technologies and to develop new technologies should be pursued. A sizable research, development, and demonstration effort can be easily justified if the potential for reducing costs can be shown. Bioprocessing systems for the treatment of nuclear and chemically hazardous wastes offer such promise

  16. Organic waste as a sustainable feedstock for platform chemicals.

    Science.gov (United States)

    Coma, M; Martinez-Hernandez, E; Abeln, F; Raikova, S; Donnelly, J; Arnot, T C; Allen, M J; Hong, D D; Chuck, C J

    2017-09-21

    Biorefineries have been established since the 1980s for biofuel production, and there has been a switch lately from first to second generation feedstocks in order to avoid the food versus fuel dilemma. To a lesser extent, many opportunities have been investigated for producing chemicals from biomass using by-products of the present biorefineries, simple waste streams. Current facilities apply intensive pre-treatments to deal with single substrate types such as carbohydrates. However, most organic streams such as municipal solid waste or algal blooms present a high complexity and variable mixture of molecules, which makes specific compound production and separation difficult. Here we focus on flexible anaerobic fermentation and hydrothermal processes that can treat complex biomass as a whole to obtain a range of products within an integrated biorefinery concept.

  17. Metabolic engineering is key to a sustainable chemical industry.

    Science.gov (United States)

    Murphy, Annabel C

    2011-08-01

    The depletion of fossil fuel stocks will prohibit their use as the main feedstock of future industrial processes. Biocatalysis is being increasingly used to reduce fossil fuel reliance and to improve the sustainability, efficiency and cost of chemical production. Even with their current small market share, biocatalyzed processes already generate approximately US$50 billion and it has been estimated that they could be used to produce up to 20% of fine chemicals by 2020. Until the advent of molecular biological technologies, the compounds that were readily accessible from renewable biomass were restricted to naturally-occurring metabolites. However, metabolic engineering has considerably broadened the range of compounds now accessible, providing access to compounds that cannot be otherwise reliably sourced, as well as replacing established chemical processes. This review presents the case for continued efforts to promote the adoption of biocatalyzed processes, highlighting successful examples of industrial chemical production from biomass and/or via biocatalyzed processes. A selection of emerging technologies that may further extend the potential and sustainability of biocatalysis are also presented. As the field matures, metabolic engineering will be increasingly crucial in maintaining our quality of life into a future where our current resources and feedstocks cannot be relied upon.

  18. Comprehensive Planning for Classification and Disposal of Solid Waste at the Industrial Parks regarding Health and Environmental Impacts

    Directory of Open Access Journals (Sweden)

    Hassan Hashemi

    2014-01-01

    Full Text Available The aim of this study is the comprehensive planning for integrated management of solid waste at the industrial parks. The share of each industrial group including food, metal, chemical, non-metallic minerals, textile, electrical and electronical, and cellulose industries were 48.2, 14.9, 6.7, 22, 0.9, 0.6, and 6.5 percent, respectively. The results showed that nearly half of total industrial waste produced from the range of biological materials are biodegradable and discharging them without observing environmental regulations leads to short-term pollution and nuisance in the acceptor environment. Also some parts of case study waste were recyclable which is considerable from viewpoint of economical and environmental pollution. Long-term impacts will appear due to improper site selection of disposal from the spatial standpoint. In this way, an approach for site selection using several socioeconomic, physical, and environmental criteria based on multicriteria decision making model (MCDM is introduced. Health risks and environment pollution such as soil and surface water may be done. It is essential to revise the studied industries layout, particularly those units which produce special waste which should be more cautious. Also stricter enforcement is required as an effective step in reducing the harmful impacts of it.

  19. [Exposure to hazardous chemical substances in furniture industry].

    Science.gov (United States)

    Pośniak, Małgorzata; Kowalska, Joanna; Makhniashvili, Ivan

    2005-01-01

    The aim of the study was to assess the exposure to organic solvents in plants of the furniture industry. Studies were conducted in five furniture plants. Hazardous chemicals present in the air at workposts were determined by capillary gas chromatography with mass spectrometry and flame ionization detection. The analysis of air samples collected at the workposts allowed to identify the following chemicals occurring during varnishing and cleaning of furniture surface elements: acetone, butan-2-one, ethyl, isobutyl and methoxypropyl acetate, 4-methylpentan-2-on, toluene, ethylbenzene and xylenes. Indices characteristic of combined exposure ranged from 0.13 to 1.67 and exceeded the limit value at 21% of workposts. The results of the study indicate that chemicals present at representative workposts during the furniture production are harmful to health of workers, especially those involved in varnishing and cleaning of furniture elements.

  20. Disposal and handling of nuclear steam generator chemical cleaning wastes

    International Nuclear Information System (INIS)

    Larrick, A.P.; Schneidmiller, D.

    1978-01-01

    A large number of pressurized water nuclear reactor electrical generating plants have experienced a corrosion-related problem with their steam generators known as denting. Denting is a mechanical deformation of the steam generator tubes that occurs at the tube support plates. Corrosion of the tube support plates occurs within the annuli through which the tubes pass and the resulting corrosion oxides, which are larger in volume than the original metal, compress and deform the tubes. In some cases, the induced stresses have been severe enough to cause tube and/or support cracking. The problem was so severe at the Turkey Point and Surrey plants that the tubing is being replaced. For less severe cases, chemical cleaning of the oxides, and other materials which deposit in the annuli from the water, is being considered. A Department of Energy-sponsored program was conducted by Consolidated Edison Co. of New York which identified several suitable cleaning solvents and led to in-plant chemical cleaning pilot demonstrations in the Indian Point Unit 1 steam generators. Current programs to improve the technology are being conducted by the Electric Power Research Institute, and the three PWR NSSS vendors with the assistance of numerous consultants, vendors, and laboratories. These programs are expected to result in more effective, less corrosive solvents. However, after a chemical cleaning is conducted, a large problem still remains- that of disposing of the spent wastes. The paper summarizes some of the methods currently available for handling and disposal of the wastes