PHYSICAL PROPERTIES OF KAOLIN/SAND SLURRY USED DURING SUBMERSIBLE MIXER PUMP TESTS AT TNX

International Nuclear Information System (INIS)

HANSEN, ERICH

2005-01-01

The purpose of this task is to characterize the physical properties of the kaolin/sand slurries used during the testing of a new submersible mixer pump (SMP) which had undergone performance testing at the TNX Waste Tank mockup facility from July 2004 through May 2005. During this time period, four identical SMPs were subjected to various water tests and four different tests using different batches of kaolin/sand slurries. The physical properties of the kaolin/sand slurries were measured for three of the four tests. In these tests, three different sample locations were used to pull samples, the SMP cooling water exit (CWE), the SMP fluid flow field (FFF), and SMP effective cleaning radius (ECR). The physical properties measured, though not for each sample, included rheology, weight percent total solids (wt% TS), density, kaolin/sand slurry particle size distribution (PSD), weight percent and particles size distribution of material greater than 45 microns

Sampling and physical and actinide characterization of colloids from the Grimsel test site

International Nuclear Information System (INIS)

Longworth, G.; Ivanovich, M.

1990-01-01

Samples of groundwater from a granite fracture at the Grimsel test site in Switzerland have been collected as part of a second intercomparison of groundwater colloid sampling and characterization techniques carried out by members of the Coco Club (colloids and complexes) sponsored by the CEC. This report describes the Harwell contribution to this exercise. The bulk of naturally occurring actinides were found to reside in solution with 10 particles/I (detection limit ∼50 nm) for samples determined by three laboratories. The colloids were shown to be negatively charged using microelectrophoresis and to be relatively stable. There was evidence of a reduction in the pH of the water after storage due to air contamination. This work has served to identify the problems associated with colloid sampling and characterization techniques

Physical characterization of steel and stainless steel metal powders

International Nuclear Information System (INIS)

Lavilla, A.O.; Lucchesi, C.G.; Sandin, O.O.

1991-01-01

A methodology has been developed for the physical characterization of steel powders (obtained by atomization) for later sintering and for the construction of porous sheets and filtrating tubes, capable of operating at temperatures between 600 deg C and 800 deg C in corrosive atmospheres. This methodology was based on the equipment and methods used for the physical characterization of uranium oxide powders. (Author) [es

Report on COTECH test procedure and characterization techniques

DEFF Research Database (Denmark)

Islam, Mohammad Aminul

that need to be attained for successful characterization of the planned demonstrators and it deals with the material characterization and prototype testing for the COTECH demonstrators. The summary of this report includes:  General description of COTECH industrial demonstrators  COTECH materials...... and material characterization techniques  Characterization techniques of the COTECH demonstrators  Functionality and lifecycle testing of the COTECH demonstrators Besides the general introduction and conclusion each section of the report is dedicated to the characterization techniques and test procedure.......Characterization techniques and test procedure requirements for innovative self-ligating dental brackets (EO) Section 5.Characterization techniques and test procedure requirements for smart diagnostic chips comprising a microfluidic channel system (GBO) Section 6.Characterization techniques and test procedure...

Facility Effect Characterization Test of NASA's HERMeS Hall Thruster

Science.gov (United States)

Huang, Wensheng; Kamhawi, Hani; Haag, Thomas W.; Ortega, Alejandro Lopez; Mikellides, Ioannis G.

2016-01-01

A test to characterize the effect of varying background pressure on NASA's 12.5-kW Hall Effect Rocket with Magnetic Shielding had being completed. This thruster is the baseline propulsion system for the Solar Electric Propulsion Technology Demonstration Mission (SEP TDM). Potential differences in thruster performance and oscillation characteristics when in ground facilities versus on-orbit are considered a primary risk for the propulsion system of the Asteroid Redirect Robotic Mission, which is a candidate for SEP TDM. The first primary objective of this test was to demonstrate that the tools being developed to predict the zero-background-pressure behavior of the thruster can provide self-consistent results. The second primary objective of this test was to provide data for refining a physics-based model of the thruster plume that will be used in spacecraft interaction studies. Diagnostics deployed included a thrust stand, Faraday probe, Langmuir probe, retarding potential analyzer, Wien filter spectrometer, and high-speed camera. From the data, a physics-based plume model was refined. Comparisons of empirical data to modeling results are shown.

Double tracks test site characterization report

International Nuclear Information System (INIS)

1996-05-01

This report presents the results of site characterization activities performed at the Double Tracks Test Site, located on Range 71 North, of the Nellis Air Force Range (NAFR) in southern Nevada. Site characterization activities included reviewing historical data from the Double Tracks experiment, previous site investigation efforts, and recent site characterization data. The most recent site characterization activities were conducted in support of an interim corrective action to remediate the Double Tracks Test Site to an acceptable risk to human health and the environment. Site characterization was performed using a phased approach. First, previously collected data and historical records sere compiled and reviewed. Generalized scopes of work were then prepared to fill known data gaps. Field activities were conducted and the collected data were then reviewed to determine whether data gaps were filled and whether other areas needed to be investigated. Additional field efforts were then conducted, as required, to adequately characterize the site. Characterization of the Double Tracks Test Site was conducted in accordance with the US Department of Energy's (DOE) Streamlined Approach for Environmental Restoration (SAFER)

Characterization and Leach Testing for REDOX Sludge and S-Saltcake Actual Waste Sample Composites

International Nuclear Information System (INIS)

Fiskum, Sandra K.; Buck, Edgar C.; Daniel, Richard C.; Draper, Kathryn E.; Edwards, Matthew K.; Hubler, Timothy L.; Jagoda, Lynette K.; Jenson, Evan D.; Kozelisky, Anne E.; Lumetta, Gregg J.; MacFarlan, Paul J.; McNamara, Bruce K.; Peterson, Reid A.; Sinkov, Sergey I.; Snow, Lanee A.; Swoboda, Robert G.

2008-01-01

This report describes processing and analysis results of boehmite waste type (Group 5) and insoluble high Cr waste type (Group 6). The sample selection, compositing, subdivision, physical and chemical characterization are described. Extensive batch leach testing was conducted to define kinetics and leach factors of selected analytes as functions of NaOH concentration and temperature. Testing supports issue M-12 resolution for the Waste Treatment Plant

Characterization and Leach Testing for REDOX Sludge and S-Saltcake Actual Waste Sample Composites

Energy Technology Data Exchange (ETDEWEB)

Fiskum, Sandra K.; Buck, Edgar C.; Daniel, Richard C.; Draper, Kathryn E.; Edwards, Matthew K.; Hubler, Timothy L.; Jagoda, Lynette K.; Jenson, Evan D.; Kozelisky, Anne E.; Lumetta, Gregg J.; MacFarlan, Paul J.; McNamara, Bruce K.; Peterson, Reid A.; Sinkov, Sergey I.; Snow, Lanee A.; Swoboda, Robert G.

2008-07-10

This report describes processing and analysis results of boehmite waste type (Group 5) and insoluble high Cr waste type (Group 6). The sample selection, compositing, subdivision, physical and chemical characterization are described. Extensive batch leach testing was conducted to define kinetics and leach factors of selected analytes as functions of NaOH concentration and temperature. Testing supports issue M-12 resolution for the Waste Treatment Plant.

Comparison of physical fitness tests in swimming

OpenAIRE

Dostálová, Sabina

2015-01-01

Title: Comparison of physical fitness tests in swimming. Objective: The aim of this thesis is to evaluate specific tests, used while testing selected physical abilities in swimming. By specific tests we mean tests realized in the water. Selected tests are intended for swim coaches, who train junior to senior age groups. Methods: The chosen method was a comparison of studies, that pursue selected specific tests. We created partial conclusions for every test by summing up the results of differe...

Developing Effective Physical Fitness Testing Standards for Pre Service Physical Educators

Science.gov (United States)

Hill, Kory; Thornburg, Roland

2016-01-01

Physical educators are often held to a higher standard of physical fitness. The ability to effectively convey the importance of physical fitness may depend upon the ability to appear physically fit. The ability to perform at a minimal level of proficiency on fitness tests was deemed important by the faculty of one physical education teacher…

W-026, health physics instrumentation operational test report

International Nuclear Information System (INIS)

Hackworth, M.F.

1998-01-01

This report documents the testing of the Health Physics Instrumentation associated with phase 2 and 3 start-up of Project W-026, WRAP. The Health Physics Instrumentation includes: Alpha and Beta Continuous Air Monitors (CAMS), Personnel Contamination Monitors (PCMs), Gamma Area Radiation Monitors (ARMs), Criticality Monitors, Alpha and Beta Smear Sample Counters, Portable Friskers, and Operator Breathing Zone Air Samplers. This OTR will cover only the Health Physics Instrumentation that was tested under the Operational test Plan for Health Physics Instrumentation (Phase 2 and 3). That instrumentation included: Alpha CAMS, Beta CAMs and ARMs located in rooms 107 and 113 of 2336-W. The remaining Health Physics Instrumentation that will be used for phase 2 and 3 start-up is tested during calibrations. These calibrations are outside the scope of the Operational Test Plan

Physical and chemical characterization of waste wood derived biochars.

Science.gov (United States)

Yargicoglu, Erin N; Sadasivam, Bala Yamini; Reddy, Krishna R; Spokas, Kurt

2015-02-01

Biochar, a solid byproduct generated during waste biomass pyrolysis or gasification in the absence (or near-absence) of oxygen, has recently garnered interest for both agricultural and environmental management purposes owing to its unique physicochemical properties. Favorable properties of biochar include its high surface area and porosity, and ability to adsorb a variety of compounds, including nutrients, organic contaminants, and some gases. Physical and chemical properties of biochars are dictated by the feedstock and production processes (pyrolysis or gasification temperature, conversion technology and pre- and post-treatment processes, if any), which vary widely across commercially produced biochars. In this study, several commercially available biochars derived from waste wood are characterized for physical and chemical properties that can signify their relevant environmental applications. Parameters characterized include: physical properties (particle size distribution, specific gravity, density, porosity, surface area), hydraulic properties (hydraulic conductivity and water holding capacity), and chemical and electrochemical properties (organic matter and organic carbon contents, pH, oxidation-reduction potential and electrical conductivity, zeta potential, carbon, nitrogen and hydrogen (CHN) elemental composition, polycyclic aromatic hydrocarbons (PAHs), heavy metals, and leachable PAHs and heavy metals). A wide range of fixed carbon (0-47.8%), volatile matter (28-74.1%), and ash contents (1.5-65.7%) were observed among tested biochars. A high variability in surface area (0.1-155.1g/m(2)) and PAH and heavy metal contents of the solid phase among commercially available biochars was also observed (0.7-83 mg kg(-1)), underscoring the importance of pre-screening biochars prior to application. Production conditions appear to dictate PAH content--with the highest PAHs observed in biochar produced via fast pyrolysis and lowest among the gasification

Physical and combustion characterization of pyrolytic oils derived from biomass material upgraded by catalytic hydrogenation

Energy Technology Data Exchange (ETDEWEB)

Vitolo, S.; Ghetti, P. (Universita di Pisa, Pisa (Italy). Dipartimento di Ingegneria Chimica)

1994-11-01

Physical and combustion properties of a pyrolytic bio-oil are determined both as-obtained and after catalytic hydrodeoxygenation. The tests demonstrate that the hydrogenation treatment improves the oil as regards combustibility, viscosity and acidity. Combustion properties of the oil have been characterized by evaporation and temperature programmed combustion profiles. Short communication. 21 refs., 4 figs., 2 tabs.

Characterizing the gender gap in introductory physics

Science.gov (United States)

Kost, Lauren E.; Pollock, Steven J.; Finkelstein, Noah D.

2009-06-01

Previous research [S. J. Pollock , Phys. Rev. ST Phys. Educ. Res. 3, 1 (2007)] showed that despite the use of interactive engagement techniques, the gap in performance between males and females on a conceptual learning survey persisted from pretest to post-test at the University of Colorado at Boulder. Such findings were counter to previously published work [M. Lorenzo , Am. J. Phys. 74, 118 (2006)]. This study begins by identifying a variety of other gender differences. There is a small but significant difference in the course grades of males and females. Males and females have significantly different prior understandings of physics and mathematics. Females are less likely to take high school physics than males, although they are equally likely to take high school calculus. Males and females also differ in their incoming attitudes and beliefs about physics. This collection of background factors is analyzed to determine the extent to which each factor correlates with performance on a conceptual post-test and with gender. Binned by quintiles, we observe that males and females with similar pretest scores do not have significantly different post-test scores (p>0.2) . The post-test data are then modeled using two regression models (multiple regression and logistic regression) to estimate the gender gap in post-test scores after controlling for these important prior factors. These prior factors account for about 70% of the observed gender gap. The results indicate that the gender gap exists in interactive physics classes at our institution but is largely associated with differences in previous physics and math knowledge and incoming attitudes and beliefs.

Startup physics tests at Temelin NPP, Unit 1

International Nuclear Information System (INIS)

Sedlacek, M.; Minarcin, M.; Toth, L.; Elko, M.; Hascik, R.

2002-01-01

The objective, scope and proceedings of the physics tests of Temelin NPP, Unit 1 physical commissioning are given in this paper. Furthermore, some results of selected physics tests are presented: reactor initial criticality test, determination of reactor power range for physics testing, measurement of control rod cluster assembly group no. 10 reactivity worth in case of limitation system LS(a) actuation, control rod cluster assembly system reactivity worth measurement with single rod cluster assembly of greatest reactivity worth stuck in fully withdrawn position, measurement of differential reactivity worth of control rod cluster assembly group no. 9, boron 'endpoint' determination and measurement of power reactivity coefficient (Authors)

Characterizing the gender gap in introductory physics

Directory of Open Access Journals (Sweden)

Lauren E. Kost

2009-01-01

Full Text Available Previous research [S. J. Pollock et al., Phys. Rev. ST Phys. Educ. Res. 3, 1 (2007] showed that despite the use of interactive engagement techniques, the gap in performance between males and females on a conceptual learning survey persisted from pretest to post-test at the University of Colorado at Boulder. Such findings were counter to previously published work [M. Lorenzo et al., Am. J. Phys. 74, 118 (2006]. This study begins by identifying a variety of other gender differences. There is a small but significant difference in the course grades of males and females. Males and females have significantly different prior understandings of physics and mathematics. Females are less likely to take high school physics than males, although they are equally likely to take high school calculus. Males and females also differ in their incoming attitudes and beliefs about physics. This collection of background factors is analyzed to determine the extent to which each factor correlates with performance on a conceptual post-test and with gender. Binned by quintiles, we observe that males and females with similar pretest scores do not have significantly different post-test scores (p>0.2. The post-test data are then modeled using two regression models (multiple regression and logistic regression to estimate the gender gap in post-test scores after controlling for these important prior factors. These prior factors account for about 70% of the observed gender gap. The results indicate that the gender gap exists in interactive physics classes at our institution but is largely associated with differences in previous physics and math knowledge and incoming attitudes and beliefs.

Characterizing the gender gap in introductory physics

Directory of Open Access Journals (Sweden)

Steven J. Pollock

2009-01-01

Full Text Available Previous research [S. J. Pollock et al., Phys. Rev. ST Phys. Educ. Res. 3, 1 (2007] showed that despite the use of interactive engagement techniques, the gap in performance between males and females on a conceptual learning survey persisted from pretest to post-test at the University of Colorado at Boulder. Such findings were counter to previously published work [M. Lorenzo et al., Am. J. Phys. 74, 118 (2006]. This study begins by identifying a variety of other gender differences. There is a small but significant difference in the course grades of males and females. Males and females have significantly different prior understandings of physics and mathematics. Females are less likely to take high school physics than males, although they are equally likely to take high school calculus. Males and females also differ in their incoming attitudes and beliefs about physics. This collection of background factors is analyzed to determine the extent to which each factor correlates with performance on a conceptual post-test and with gender. Binned by quintiles, we observe that males and females with similar pretest scores do not have significantly different post-test scores (p>0.2 . The post-test data are then modeled using two regression models (multiple regression and logistic regression to estimate the gender gap in post-test scores after controlling for these important prior factors. These prior factors account for about 70% of the observed gender gap. The results indicate that the gender gap exists in interactive physics classes at our institution but is largely associated with differences in previous physics and math knowledge and incoming attitudes and beliefs.

Tests of the particle physics-physical cosmology interface

International Nuclear Information System (INIS)

Schramm, D.N.

1993-01-01

Three interrelated interfaces of particle physics and physical cosmology are discussed: (1) inflation and other phase transitions; (2) Big Bang Nucleosynthesis (and also the quark-hadron transition); and (3) structure formation (including dark matter). Recent observations that affect each of these topics are discussed. Topic number 1 is shown to be consistent with the COBE observations but not proven and it may be having problems with some age-expansion data. Topic number 2 has now been well-tested and is an established ''pillar'' of the Big Bang. Topic number 3 is the prime arena of current physical cosmological activity. Experiments to resolve the current exciting, but still ambiguous, situation following the COBE results are discussed

JOHNSON-MATTHEY DIFFUSER CHARACTERIZATION TESTING

International Nuclear Information System (INIS)

Foster, P; James Klein, J; Henry Sessions, H; Gregg Morgan, G

2007-01-01

A diffuser/permeator commercially fabricated by Johnson-Matthey was purchased for characterization testing at the Savannah River National Laboratory (SRNL). A test system was fabricated to not only feed and bleed flows and pressures, but also permeate pressure for flows up to 20 SLPM

Physical characterization of the Skua fast burst assembly

International Nuclear Information System (INIS)

Paternoster, R.; Bounds, J.; Sanchez, R.; Miko, D.

1994-01-01

In this paper we discuss the system design and ongoing efforts to characterize the machine physics and operating properties of the Skua fast burst assembly. The machine is currently operating up to prompt critical while we await approval for super-prompt burst operations. Efforts have centered on characterizing neutron kinetic properties, comparing calculated and measured temperature coefficients and power distributions, improving the burst reproducibility, examining the site-wide dose characteristics, and fitting the machine with cooling and filtration systems

Fitness Testing in Physical Education--A Misdirected Effort in Promoting Healthy Lifestyles and Physical Activity?

Science.gov (United States)

Cale, Lorraine; Harris, Jo

2009-01-01

Background: Physical fitness testing is commonplace within schools and the physical education (PE) curriculum, with advocates claiming one of the key purposes of testing to be the promotion of healthy lifestyles and physical activity. Despite this, much controversy has surrounded the fitness testing of young people. Purpose: This paper draws on…

The characterization, replication and testing of dermal denticles of Scyliorhinus canicula for physical mechanisms of biofouling prevention

International Nuclear Information System (INIS)

Sullivan, Timothy; Regan, Fiona

2011-01-01

There is a current need to develop novel non-toxic antifouling materials. The mechanisms utilized by marine organisms to prevent fouling of external surfaces are of interest in this regard. Biomimicry of these mechanisms and the ability to transfer the antifouling characteristics of these surfaces to artificial surfaces are a highly attractive prospect to those developing antifouling technologies. In order to achieve this, the mechanisms responsible for any antifouling ability must be elucidated from the study of the natural organism and the critical surface parameters responsible for fouling reduction. Dermal denticles of members of the shark family have been speculated to possess some natural, as yet unidentified antifouling mechanism related to the physical presence of denticles. In this study, the dermal denticles of one particular member of the slow-swimming sharks, Scyliorhinus canicula were characterized and it was found that a significant natural variation in denticle dimensions exists in this species. The degree of denticle surface contamination was quantified on denticles at various locations and it was determined that the degree of contamination of the dorsal surface of denticles varies with the position on the shark body. In addition, we successfully produced synthetic sharkskin samples using the real skin as a template. Testing of the produced synthetic skin in field conditions resulted in significant differences in material attachment on surfaces exhibiting denticles of different dimensions.

The characterization, replication and testing of dermal denticles of Scyliorhinus canicula for physical mechanisms of biofouling prevention

Energy Technology Data Exchange (ETDEWEB)

Sullivan, Timothy; Regan, Fiona, E-mail: fiona.regan@dcu.ie [Marine and Environmental Sensing Technology Hub (MESTECH), National Centre for Sensor Research, School of Chemical Sciences, Dublin City University, Glasnevin, Dublin 9 (Ireland)

2011-12-15

There is a current need to develop novel non-toxic antifouling materials. The mechanisms utilized by marine organisms to prevent fouling of external surfaces are of interest in this regard. Biomimicry of these mechanisms and the ability to transfer the antifouling characteristics of these surfaces to artificial surfaces are a highly attractive prospect to those developing antifouling technologies. In order to achieve this, the mechanisms responsible for any antifouling ability must be elucidated from the study of the natural organism and the critical surface parameters responsible for fouling reduction. Dermal denticles of members of the shark family have been speculated to possess some natural, as yet unidentified antifouling mechanism related to the physical presence of denticles. In this study, the dermal denticles of one particular member of the slow-swimming sharks, Scyliorhinus canicula were characterized and it was found that a significant natural variation in denticle dimensions exists in this species. The degree of denticle surface contamination was quantified on denticles at various locations and it was determined that the degree of contamination of the dorsal surface of denticles varies with the position on the shark body. In addition, we successfully produced synthetic sharkskin samples using the real skin as a template. Testing of the produced synthetic skin in field conditions resulted in significant differences in material attachment on surfaces exhibiting denticles of different dimensions.

The characterization, replication and testing of dermal denticles of Scyliorhinus canicula for physical mechanisms of biofouling prevention.

Science.gov (United States)

Sullivan, Timothy; Regan, Fiona

2011-12-01

There is a current need to develop novel non-toxic antifouling materials. The mechanisms utilized by marine organisms to prevent fouling of external surfaces are of interest in this regard. Biomimicry of these mechanisms and the ability to transfer the antifouling characteristics of these surfaces to artificial surfaces are a highly attractive prospect to those developing antifouling technologies. In order to achieve this, the mechanisms responsible for any antifouling ability must be elucidated from the study of the natural organism and the critical surface parameters responsible for fouling reduction. Dermal denticles of members of the shark family have been speculated to possess some natural, as yet unidentified antifouling mechanism related to the physical presence of denticles. In this study, the dermal denticles of one particular member of the slow-swimming sharks, Scyliorhinus canicula were characterized and it was found that a significant natural variation in denticle dimensions exists in this species. The degree of denticle surface contamination was quantified on denticles at various locations and it was determined that the degree of contamination of the dorsal surface of denticles varies with the position on the shark body. In addition, we successfully produced synthetic sharkskin samples using the real skin as a template. Testing of the produced synthetic skin in field conditions resulted in significant differences in material attachment on surfaces exhibiting denticles of different dimensions.

Johnson-Matthey diffuser characterization testing

International Nuclear Information System (INIS)

Foster, P. J.; Klein, J. E.; Sessions, H. T.; Morgan, G. A.

2008-01-01

A diffuser/permeator commercially fabricated by Johnson-Matthey was purchased for characterization testing at the Savannah River National Laboratory (SRNL). A test system was fabricated to test not only feed and bleed flows and pressures, but also permeate pressure for flows up to 20 sLPM. The tests described in this paper consider the effect of various inert gas types, feed gas compositions, methods for temperature control, and varying tube pressure on permeation of H 2 through the Pd/Ag tubes. (authors)

Physical characterization and kinetic modelling of matrix tablets of ...

African Journals Online (AJOL)

release mechanisms were characterized by kinetic modeling. Analytical ... findings demonstrate that both the desired physical characteristics and drug release profiles were obtained ..... on the compression, mechanical, and release properties.

MO-AB-206-00: Nuclear Medicine Physics and Testing

Energy Technology Data Exchange (ETDEWEB)

NONE

2016-06-15

This education session will cover the physics and operation principles of gamma cameras and PET scanners. The first talk will focus on PET imaging. An overview of the principles of PET imaging will be provided, including positron decay physics, and the transition from 2D to 3D imaging. More recent advances in hardware and software will be discussed, such as time-of-flight imaging, and improvements in reconstruction algorithms that provide for options such as depth-of-interaction corrections. Quantitative applications of PET will be discussed, as well as the requirements for doing accurate quantitation. Relevant performance tests will also be described. Learning Objectives: Be able to describe basic physics principles of PET and operation of PET scanners. Learn about recent advances in PET scanner hardware technology. Be able to describe advances in reconstruction techniques and improvements Be able to list relevant performance tests. The second talk will focus on gamma cameras. The Nuclear Medicine subcommittee has charged a task group (TG177) to develop a report on the current state of physics testing of gamma cameras, SPECT, and SPECT/CT systems. The report makes recommendations for performance tests to be done for routine quality assurance, annual physics testing, and acceptance tests, and identifies those needed satisfy the ACR accreditation program and The Joint Commission imaging standards. The report is also intended to be used as a manual with detailed instructions on how to perform tests under widely varying conditions. Learning Objectives: At the end of the presentation members of the audience will: Be familiar with the tests recommended for routine quality assurance, annual physics testing, and acceptance tests of gamma cameras for planar imaging. Be familiar with the tests recommended for routine quality assurance, annual physics testing, and acceptance tests of SPECT systems. Be familiar with the tests of a SPECT/CT system that include the CT images

MO-AB-206-00: Nuclear Medicine Physics and Testing

International Nuclear Information System (INIS)

2016-01-01

This education session will cover the physics and operation principles of gamma cameras and PET scanners. The first talk will focus on PET imaging. An overview of the principles of PET imaging will be provided, including positron decay physics, and the transition from 2D to 3D imaging. More recent advances in hardware and software will be discussed, such as time-of-flight imaging, and improvements in reconstruction algorithms that provide for options such as depth-of-interaction corrections. Quantitative applications of PET will be discussed, as well as the requirements for doing accurate quantitation. Relevant performance tests will also be described. Learning Objectives: Be able to describe basic physics principles of PET and operation of PET scanners. Learn about recent advances in PET scanner hardware technology. Be able to describe advances in reconstruction techniques and improvements Be able to list relevant performance tests. The second talk will focus on gamma cameras. The Nuclear Medicine subcommittee has charged a task group (TG177) to develop a report on the current state of physics testing of gamma cameras, SPECT, and SPECT/CT systems. The report makes recommendations for performance tests to be done for routine quality assurance, annual physics testing, and acceptance tests, and identifies those needed satisfy the ACR accreditation program and The Joint Commission imaging standards. The report is also intended to be used as a manual with detailed instructions on how to perform tests under widely varying conditions. Learning Objectives: At the end of the presentation members of the audience will: Be familiar with the tests recommended for routine quality assurance, annual physics testing, and acceptance tests of gamma cameras for planar imaging. Be familiar with the tests recommended for routine quality assurance, annual physics testing, and acceptance tests of SPECT systems. Be familiar with the tests of a SPECT/CT system that include the CT images

A statistical characterization of the finger tapping test: modeling, estimation, and applications.

Science.gov (United States)

Austin, Daniel; McNames, James; Klein, Krystal; Jimison, Holly; Pavel, Misha

2015-03-01

Sensory-motor performance is indicative of both cognitive and physical function. The Halstead-Reitan finger tapping test is a measure of sensory-motor speed commonly used to assess function as part of a neuropsychological evaluation. Despite the widespread use of this test, the underlying motor and cognitive processes driving tapping behavior during the test are not well characterized or understood. This lack of understanding may make clinical inferences from test results about health or disease state less accurate because important aspects of the task such as variability or fatigue are unmeasured. To overcome these limitations, we enhanced the tapper with a sensor that enables us to more fully characterize all the aspects of tapping. This modification enabled us to decompose the tapping performance into six component phases and represent each phase with a set of parameters having clear functional interpretation. This results in a set of 29 total parameters for each trial, including change in tapping over time, and trial-to-trial and tap-to-tap variability. These parameters can be used to more precisely link different aspects of cognition or motor function to tapping behavior. We demonstrate the benefits of this new instrument with a simple hypothesis-driven trial comparing single and dual-task tapping.

Results of Detailed Hydrologic Characterization Tests - Fiscal Year 2000

International Nuclear Information System (INIS)

Spane, Frank A; Thorne, Paul D; Newcomer, Darrell R

2001-01-01

This report provides the results of detailed hydrologic characterization tests conducted within eleven Hanford Site wells during fiscal year 2000. Detailed characterization tests performed included groundwater-flow characterization; barometric response evaluation; slug tests; single-well tracer tests; constant-rate pumping tests; and in-well, vertical flow tests. Hydraulic property estimates obtained from the detailed hydrologic tests include transmissivity; hydraulic conductivity; specific yield; effective porosity; in-well, lateral flow velocity; aquifer-flow velocity; vertical distribution of hydraulic conductivity (within the well-screen section); and in-well, vertical flow velocity. In addition, local groundwater-flow characteristics (i.e., hydraulic gradient and flow direction) were determined for four sites where detailed well testing was performed

Reload Startup Physics Tests for Tianwan Nuclear Power station

International Nuclear Information System (INIS)

Yang Xiaoqiang; Li Wenshuang; Li Youyi; Yao Jinguo; Li Zaipeng Jiangsu

2010-01-01

This paper briefly describes the test purposes, test items, test schedules and test equipment's for reload startup physics test's on Unit 1 and 2 of Tianwan Nuclear Power station. Then, an overview of the previous thrice tests and evaluations on the tests results are presented. In the end, the paper shows the development and work direction of optimization project for reload startup physics tests on Unit 1 and 2 of Tianwan Nuclear Power station. (Authors)

Test plan for FY-94 digface characterization field experiments

International Nuclear Information System (INIS)

Josten, N.E.; Roybal, L.G.

1994-08-01

The digface characterization concept has been under development at the Idaho National Engineering Laboratory (INEL) since fiscal year (FY) 1992 through the support of the Buried Waste Integrated Demonstration Program. A digface characterization system conducts continuous subsurface characterization simultaneously with retrieval of hazardous and radioactive waste from buried waste sites. The system deploys multiple sensors at the retrieval operation digface and collects data that provide a basis for detecting, locating, and classifying buried materials and hazardous conditions before they are disturbed by the retrieval equipment. This test plan describes ongoing efforts to test the digface characterization concept at the INEL's Cold Test Pit using a simplified prototype deployment apparatus and off-the-shelf sensors. FY-94 field experiments will explore problems in object detection and classification. Detection and classification of objects are fundamental to three of the four primary functions of digface characterization during overburden removal. This test plan establishes procedures for collecting and validating the digface characterization data sets. Analysis of these data will focus on testing and further developing analysis methods for object detection and classification during overburden removal

Mathematical Reasoning Requirements in Swedish National Physics Tests

Science.gov (United States)

Johansson, Helena

2016-01-01

This paper focuses on one aspect of mathematical competence, namely mathematical reasoning, and how this competency influences students' knowing of physics. This influence was studied by analysing the mathematical reasoning requirements upper secondary students meet when solving tasks in national physics tests. National tests are constructed to…

Two methodologies for physical penetration testing using social engineering

NARCIS (Netherlands)

Dimkov, T.; van Cleeff, A.; Pieters, Wolter; Hartel, Pieter H.

2010-01-01

Penetration tests on IT systems are sometimes coupled with physical penetration tests and social engineering. In physical penetration tests where social engineering is allowed, the penetration tester directly interacts with the employees. These interactions are usually based on deception and if not

Physical separations soil washing system cold test results

Energy Technology Data Exchange (ETDEWEB)

McGuire, J.P.

1993-07-28

This test summary describes the objectives, methodology, and results of a physical separations soil-washing system setup and shakedown test using uncontaminated soil. The test is being conducted in preparation for a treatability test to be conducted in the North Pond of the 300-FF-1 Operable Unit. It will be used to assess the feasibility of using a physical separations process to reduce the volume of contaminated soils in the 300-FF-1 Operable Unit. The test is described in DOE-RL (1993). The setup test was conducted at an uncontrolled area located approximately 3.2 km northwest of the 300-FF-1 Operable Unit. The material processed was free of contamination. The physical separation equipment to be used in the test was transferred to the US Department of Energy (DOE) by the US Environmental Protection Agency (EPA) Risk Reduction Engineering Laboratory. On May 13, 1993, soil-washing equipment was moved to the cold test location. Design assistance and recommendation for operation was provided by the EPA.

Gas characterization system software acceptance test procedure

International Nuclear Information System (INIS)

Vo, C.V.

1996-01-01

This document details the Software Acceptance Testing of gas characterization systems. The gas characterization systems will be used to monitor the vapor spaces of waste tanks known to contain measurable concentrations of flammable gases

Characterization of Physic nut (Jatropha curcas L.) shells

NARCIS (Netherlands)

Wever, Diego; Heeres, H. J.; Broekhuis, Antonius A.

The characterization of Physic nut shells was done using the wet chemical analysis of wood components. The obtained fractions were analyzed using IR, NMR, GPC, ICP and MALDI-TOF mass spectroscopy. TGA was used to determine the fixed carbon (+ash) and water content of the shells. The results of wet

Gas characterization system software acceptance test report

International Nuclear Information System (INIS)

Vo, C.V.

1996-01-01

This document details the results of software acceptance testing of gas characterization systems. The gas characterization systems will be used to monitor the vapor spaces of waste tanks known to contain measurable concentrations of flammable gases

21 CFR 58.105 - Test and control article characterization.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Test and control article characterization. 58.105... GENERAL GOOD LABORATORY PRACTICE FOR NONCLINICAL LABORATORY STUDIES Test and Control Articles § 58.105 Test and control article characterization. (a) The identity, strength, purity, and composition or other...

Physical property characterization of 183-H Basin sludge

International Nuclear Information System (INIS)

Biyani, R.K.; Delegard, C.H.

1995-01-01

This document describes the characterization of 183-H Basin sludge physical properties, e.g. bulk density of sludge and absorbent, and determination of free liquids. Calcination of crucible-size samples of sludge was also done and the resulting 'loss-on-ignition' was compared to the theoretical weight loss based on sludge analysis obtained from Weston Labs

ACL injury: How do the physical examination tests compare?

Science.gov (United States)

Koster, Christiaan H; Harmsen, Annelieke Mk; Lichtenberg, Miranda C; Bloemers, Frank W

2018-03-01

Three physical examination tests are most commonly used to evaluate cruciate ligament injury. The best known and most frequently used technique is the anterior drawer test. The other 2 tests, the Lachman test and the pivot shift test, are more difficult to perform and are used less often, especially by physicians untrained in their use. In addition, there is a relatively new diagnostic test: the lever sign test. The aim of our article is to provide a short, clinically relevant overview of the literature and to assess the diagnostic value of physical examination for the primary care physician.

Automated testing of health physics instruments

International Nuclear Information System (INIS)

Swinth, K.L.; Endres, A.W.; Hadley, R.T.; Kenoyer, J.L.

1983-12-01

A microcomputer controlled CAMAC system has been adapted for automated testing of health physics survey instruments. Once the survey instrument is positioned, the system automatically performs tests for angular dependence or battery lifetime. Rotation of the instrument is performed by a computer controlled stepping motor while readout is performed by an auto ranging digital volt meter and data stored on computer disks

Characterization, Leaching, and Filtration Testing for Tributyl Phosphate (TBP, Group 7) Actual Waste Sample Composites

Energy Technology Data Exchange (ETDEWEB)

Edwards, Matthew K.; Billing, Justin M.; Blanchard, David L.; Buck, Edgar C.; Casella, Amanda J.; Casella, Andrew M.; Crum, J. V.; Daniel, Richard C.; Draper, Kathryn E.; Fiskum, Sandra K.; Jagoda, Lynette K.; Jenson, Evan D.; Kozelisky, Anne E.; MacFarlan, Paul J.; Peterson, Reid A.; Shimskey, Rick W.; Snow, Lanee A.; Swoboda, Robert G.

2009-03-09

.A testing program evaluating actual tank waste was developed in response to Task 4 from the M-12 External Flowsheet Review Team (EFRT) issue response plan. The bulk water-insoluble solid wastes that are anticipated to be delivered to the Waste Treatment and Immobilization Plant (WTP) were identified according to type such that the actual waste testing could be targeted to the relevant categories. Eight broad waste groupings were defined. Samples available from the 222S archive were identified and obtained for testing. The actual waste-testing program included homogenizing the samples by group, characterizing the solids and aqueous phases, and performing parametric leaching tests. The tributyl phosphate sludge (TBP, Group 7) is the subject of this report. The Group 7 waste was anticipated to be high in phosphorus as well as aluminum in the form of gibbsite. Both are believed to exist in sufficient quantities in the Group 7 waste to address leaching behavior. Thus, the focus of the Group 7 testing was on the removal of both P and Al. The waste-type definition, archived sample conditions, homogenization activities, characterization (physical, chemical, radioisotope, and crystal habit), and caustic leaching behavior as functions of time, temperature, and hydroxide concentration are discussed in this report. Testing was conducted according to TP-RPP-WTP-467.

Historical hydronuclear testing: Characterization and remediation technologies

Energy Technology Data Exchange (ETDEWEB)

Shaulis, L.; Wilson, G.; Jacobson, R.

1997-09-01

This report examines the most current literature and information available on characterization and remediation technologies that could be used on the Nevada Test Site (NTS) historical hydronuclear test areas. Historical hydronuclear tests use high explosives and a small amount of plutonium. The explosion scatters plutonium within a contained subsurface environment. There is currently a need to characterize these test areas to determine the spatial extent of plutonium in the subsurface and whether geohydrologic processes are transporting the plutonium away from the event site. Three technologies were identified to assist in the characterization of the sites. These technologies are the Pipe Explorer{trademark}, cone penetrometer, and drilling. If the characterization results indicate that remediation is needed, three remediation technologies were identified that should be appropriate, namely: capping or sealing the surface, in situ grouting, and in situ vitrification. Capping the surface would prevent vertical infiltration of water into the soil column, but would not restrict lateral movement of vadose zone water. Both the in situ grouting and vitrification techniques would attempt to immobilize the radioactive contaminants to restrict or prevent leaching of the radioactive contaminants into the groundwater. In situ grouting uses penetrometers or boreholes to inject the soil below the contaminant zone with low permeability grout. In situ vitrification melts the soil containing contaminants into a solid block. This technique would provide a significantly longer contaminant immobilization, but some research and development would be required to re-engineer existing systems for use at deep soil depths. Currently, equipment can only handle shallow depth vitrification. After existing documentation on the historical hydronuclear tests have been reviewed and the sites have been visited, more specific recommendations will be made.

Historical hydronuclear testing: Characterization and remediation technologies

International Nuclear Information System (INIS)

Shaulis, L.; Wilson, G.; Jacobson, R.

1997-09-01

This report examines the most current literature and information available on characterization and remediation technologies that could be used on the Nevada Test Site (NTS) historical hydronuclear test areas. Historical hydronuclear tests use high explosives and a small amount of plutonium. The explosion scatters plutonium within a contained subsurface environment. There is currently a need to characterize these test areas to determine the spatial extent of plutonium in the subsurface and whether geohydrologic processes are transporting the plutonium away from the event site. Three technologies were identified to assist in the characterization of the sites. These technologies are the Pipe Explorer trademark, cone penetrometer, and drilling. If the characterization results indicate that remediation is needed, three remediation technologies were identified that should be appropriate, namely: capping or sealing the surface, in situ grouting, and in situ vitrification. Capping the surface would prevent vertical infiltration of water into the soil column, but would not restrict lateral movement of vadose zone water. Both the in situ grouting and vitrification techniques would attempt to immobilize the radioactive contaminants to restrict or prevent leaching of the radioactive contaminants into the groundwater. In situ grouting uses penetrometers or boreholes to inject the soil below the contaminant zone with low permeability grout. In situ vitrification melts the soil containing contaminants into a solid block. This technique would provide a significantly longer contaminant immobilization, but some research and development would be required to re-engineer existing systems for use at deep soil depths. Currently, equipment can only handle shallow depth vitrification. After existing documentation on the historical hydronuclear tests have been reviewed and the sites have been visited, more specific recommendations will be made

Relationship between physical development and physical readiness among skilled wrestlers

Directory of Open Access Journals (Sweden)

Yura Tropin

2018-02-01

Full Text Available Purpose: to determine the relationship between physical development and physical readiness among qualified wrestlers. Material & Methods: in the study involved thirty qualified wrestlers, aged 19–22 years. For the purpose of analyzing indicators of physical development and physical preparedness, pedagogical testing. Results: the results of the study testify to the homogeneity of the indices of physical development of the athletes under study, the coefficient of variation is in the range from 2,43% to 10,93%. It is revealed that the indices of physical readiness of qualified wrestlers are characterized mainly by small variation in the testing of speed-strength qualities, coordination abilities, general and strength endurance, and average – in the results of special endurance. Conclusion: it is determined that the most informative indicators of physical development are the weight of the wrestler's body, which has a connection with 15 physical preparedness tests, followed by a vital index (12 statistically reliable relationships and a strength index (11 interrelations.

A physical-topological characterization of group response to nuclear power

International Nuclear Information System (INIS)

Harms, A.A.; McMaster Univ., Hamilton, Ontario

1980-01-01

A physical-topological model of societal response to the introduction of a technology such as nuclear power is proposed. The formation is based on a conceptual-geometric construct familiar in physics and mathematics. An interesting feature of the model is that it provides for the intrinsic inclusion of such intra-societal conflict manifestations as opinion reversals, opinion polarizations and apparent inconsistencies. The general applicability of this characterization to other societal conflict domains is suggested. (author)

Using Virtual Testing for Characterization of Composite Materials

Science.gov (United States)

Harrington, Joseph

Composite materials are finally providing uses hitherto reserved for metals in structural systems applications -- airframes and engine containment systems, wraps for repair and rehabilitation, and ballistic/blast mitigation systems. They have high strength-to-weight ratios, are durable and resistant to environmental effects, have high impact strength, and can be manufactured in a variety of shapes. Generalized constitutive models are being developed to accurately model composite systems so they can be used in implicit and explicit finite element analysis. These models require extensive characterization of the composite material as input. The particular constitutive model of interest for this research is a three-dimensional orthotropic elasto-plastic composite material model that requires a total of 12 experimental stress-strain curves, yield stresses, and Young's Modulus and Poisson's ratio in the material directions as input. Sometimes it is not possible to carry out reliable experimental tests needed to characterize the composite material. One solution is using virtual testing to fill the gaps in available experimental data. A Virtual Testing Software System (VTSS) has been developed to address the need for a less restrictive method to characterize a three-dimensional orthotropic composite material. The system takes in the material properties of the constituents and completes all 12 of the necessary characterization tests using finite element (FE) models. Verification and validation test cases demonstrate the capabilities of the VTSS.

Clinical-epidemiological characterization of leprosy cases with physical disabilities

Directory of Open Access Journals (Sweden)

Gleciane Costa de Sousa

2017-01-01

Full Text Available To characterize the clinical-epidemiological profile of cases of multibacillary leprosy, diagnosed with physical disabilities. Methods: this is a cross-sectional and retrospective study. The sample consisted of 276 cases of diagnosed leprosy. Results: leprosy mainly affects males, of brown skin color, low education and with a mean age of 51.96 years old (standard deviation, SD=20.33 years old. The Virchowian and dimorphic clinical forms are mainly responsible for the transmission of the disease and the development of physical disabilities. Decreased or lost sensation in hands and feet, trophic ulcers and traumatic injuries, as well as clawed hands were the physical disabilities prevalent in the study. Conclusion: the cases with physical disabilities are predominantly affected by multibacillary clinical forms, and they can be inferred in the maintenance of the transmission chain and the late detection of severe forms of leprosy.

Commissioning experience and beam physics measurements at the SwissFEL Injector test Facility

CERN Document Server

Schietinger, T.; Aiba, M.; Arsov, V.; Bettoni, S.; Beutner, B.; Calvi, M.; Craievich, P.; Dehler, M.; Frei, F.; Ganter, R.; Hauri, C. P.; Ischebeck, R.; Ivanisenko, Y.; Janousch, M.; Kaiser, M.; Keil, B.; Löhl, F.; Orlandi, G. L.; Ozkan Loch, C.; Peier, P.; Prat, E.; Raguin, J.-Y.; Reiche, S.; Schilcher, T.; Wiegand, P.; Zimoch, E.; Anicic, D.; Armstrong, D.; Baldinger, M.; Baldinger, R.; Bertrand, A.; Bitterli, K.; Bopp, M.; Brands, H.; Braun, H. H.; Brönnimann, M.; Brunnenkant, I.; Chevtsov, P.; Chrin, J.; Citterio, A.; Csatari Divall, M.; Dach, M.; Dax, A.; Ditter, R.; Divall, E.; Falone, A.; Fitze, H.; Geiselhart, C.; Guetg, M. W.; Hämmerli, F.; Hauff, A.; Heiniger, M.; Higgs, C.; Hugentobler, W.; Hunziker, S.; Janser, G.; Kalantari, B.; Kalt, R.; Kim, Y.; Koprek, W.; Korhonen, T.; Krempaska, R.; Laznovsky, M.; Lehner, S.; Le Pimpec, F.; Lippuner, T.; Lutz, H.; Mair, S.; Marcellini, F.; Marinkovic, G.; Menzel, R.; Milas, N.; Pal, T.; Pollet, P.; Portmann, W.; Rezaeizadeh, A.; Ritt, S.; Rohrer, M.; Schär, M.; Schebacher, L.; Scherrer, St.; Schlott, V.; Schmidt, T.; Schulz, L.; Smit, B.; Stadler, M.; Steffen, Bernd; Stingelin, L.; Sturzenegger, W.; Treyer, D. M.; Trisorio, A.; Tron, W.; Vicario, C.; Zennaro, R.; Zimoch, D.

2016-10-26

The SwissFEL Injector Test Facility operated at the Paul Scherrer Institute between 2010 and 2014, serving as a pilot plant and test bed for the development and realization of SwissFEL, the x-ray Free Electron Laser facility under construction at the same institute. The test facility consisted of a laser-driven rf electron gun followed by an S-band booster linac, a magnetic bunch compression chicane and a diagnostic section including atransverse deflecting rf cavity. It delivered electron bunchesof up to200 pC chargeand up to 250 MeV beam energy at a repetition rate of 10 Hz. The measurements performed at the test facility not only demonstrated the beam parameters required to drive the first stage of a FEL facility, but also led to significant advances in instrumentation technologies, beam characterization methods and the generation, transport and compression of ultralow-emittance beams. We give a comprehensive overview of the commissioning experience of the principal subsystems and the beam physics measureme...

Testable physics by design

International Nuclear Information System (INIS)

Choi, Chansoo; Han, Min Cheol; Kim, Chan Hyeong; Kim, Sung Hun; Hoff, Gabriela; Pia, Maria Grazia; Saracco, Paolo; Weidenspointner, Georg

2015-01-01

The ability to test scientific software needs to be supported by adequate software design. Legacy software systems are often characterized by the difficulty to test parts of the software, mainly due to existing dependencies on other parts. Methods to improve the testability of physics software are discussed, along with open issues specific to physics software for Monte Carlo particle transport. The discussion is supported by examples drawn from the experience with validating Geant4 physics. (paper)

A test harness for accelerating physics parameterization advancements into operations

Science.gov (United States)

Firl, G. J.; Bernardet, L.; Harrold, M.; Henderson, J.; Wolff, J.; Zhang, M.

2017-12-01

The process of transitioning advances in parameterization of sub-grid scale processes from initial idea to implementation is often much quicker than the transition from implementation to use in an operational setting. After all, considerable work must be undertaken by operational centers to fully test, evaluate, and implement new physics. The process is complicated by the scarcity of like-to-like comparisons, availability of HPC resources, and the ``tuning problem" whereby advances in physics schemes are difficult to properly evaluate without first undertaking the expensive and time-consuming process of tuning to other schemes within a suite. To address this process shortcoming, the Global Model TestBed (GMTB), supported by the NWS NGGPS project and undertaken by the Developmental Testbed Center, has developed a physics test harness. It implements the concept of hierarchical testing, where the same code can be tested in model configurations of varying complexity from single column models (SCM) to fully coupled, cycled global simulations. Developers and users may choose at which level of complexity to engage. Several components of the physics test harness have been implemented, including a SCM and an end-to-end workflow that expands upon the one used at NOAA/EMC to run the GFS operationally, although the testbed components will necessarily morph to coincide with changes to the operational configuration (FV3-GFS). A standard, relatively user-friendly interface known as the Interoperable Physics Driver (IPD) is available for physics developers to connect their codes. This prerequisite exercise allows access to the testbed tools and removes a technical hurdle for potential inclusion into the Common Community Physics Package (CCPP). The testbed offers users the opportunity to conduct like-to-like comparisons between the operational physics suite and new development as well as among multiple developments. GMTB staff have demonstrated use of the testbed through a

Maximum physical capacity testing in cancer patients undergoing chemotherapy

DEFF Research Database (Denmark)

Knutsen, L.; Quist, M; Midtgaard, J

2006-01-01

BACKGROUND: Over the past few years there has been a growing interest in the field of physical exercise in rehabilitation of cancer patients, leading to requirements for objective maximum physical capacity measurement (maximum oxygen uptake (VO(2max)) and one-repetition maximum (1RM)) to determin...... early in the treatment process. However, the patients were self-referred and thus highly motivated and as such are not necessarily representative of the whole population of cancer patients treated with chemotherapy....... in performing maximum physical capacity tests as these motivated them through self-perceived competitiveness and set a standard that served to encourage peak performance. CONCLUSION: The positive attitudes in this sample towards maximum physical capacity open the possibility of introducing physical testing...

Physical characterization of austenitic stainless steels AISI 304 and AISI 348 L*

International Nuclear Information System (INIS)

Teodoro, Celso Antonio; Silva, Jose Eduardo Rosa da

2009-01-01

The study of radiation damages in metals and metallic alloys used as structural materials in nuclear reactors has a strategic meaning to the nuclear technology because it treats of performance of these materials in conditions that simulate the conditions of work in power reactors. Then it becomes necessary to know the essential physical properties of these materials, properties that are sensitive to the microstructural changes that occurred during the irradiation. The purpose of this work is to characterize, initially, some pre-irradiation properties of the stainless steels AISI 304 and AISI 348 L * , such as mechanical (stress-strain and microhardness) and electrical (resistivity). The AISI 348 L * has been studied for use as fuel cladding material. Both materials will be tested after irradiation in the IEA-R1 core and their properties will be compared with those in the pre-irradiated condition. The morphology of the fractured zones after tensile tests was observed using SEM (scanning electron microscopy). (author)

Glovebox characterization and barrier integrity testing using fluorescent powder

International Nuclear Information System (INIS)

Wahlquist, D.R.

1996-01-01

This paper presents a method for characterizing the spread of contamination and testing the barrier integrity of a new glovebox during material transfer operations and glove change-outs using fluorescent powder. Argonne National Laboratory-West has performed this test on several new gloveboxes prior to putting them into service. The test is performed after the glovebox has been leak tested and all systems have been verified to be operational. The purpose of the test is to show that bag-in/bag-out operations and glove change-outs can be accomplished without spreading the actual contaminated material to non-contaminated areas. The characterization test also provides information as to where contamination might be expected to build-up during actual operations. The fluorescent powder is used because it is easily detectable using an ultra-violet light and disperses in a similar fashion to radioactive material. The characterization and barrier integrity test of a glovebox using fluorescent powder provides a visual method of determining areas of potential contamination accumulation and helps evaluate the ability to perform clean transfer operations and glove change-outs

Hanford Site physical separations CERCLA treatability test plan

International Nuclear Information System (INIS)

1992-03-01

This test plan describes specifications, responsibilities, and general procedures to be followed to conduct a physical separations soil treatability test in the North Process Pond of the 300-FF-1 Operable Unit at the Hanford Site, Washington. The objective of this test is to evaluate the use of physical separation systems as a means of concentrating chemical and radioactive contaminants into fine soil fractions and thereby minimizing waste volumes. If successful the technology could be applied to clean up millions of cubic meters of contaminated soils in waste sites at Hanford and other sites. It is not the intent of this test to remove contaminated materials from the fine soils. Physical separation is a simple and comparatively low cost technology to potentially achieve a significant reduction in the volume of contaminated soils. Organic contaminants are expected to be insignificant for the 300-FF-I Operable Unit test, and further removal of metals and radioactive contaminants from the fine fraction of soils will require secondary treatment such as chemical extraction, electromagnetic separation, or other technologies. Additional investigations/testing are recommended to assess the economic and technical feasibility of applying secondary treatment technologies, but are not within the scope of this test. This plan provides guidance and specifications for the treatability test to be conducted as a service contract. More detailed instructions and procedures will be provided as part of the vendors (sellers) proposal. The procedures will be approved by Westinghouse Hanford Company (Westinghouse Hanford) and finalized by the seller prior to initiating the test

Characteristics of HTTR's startup physics tests

International Nuclear Information System (INIS)

Nojiri, N.; Nakano, M.; Takeuchi, M.; Pohl, P.; Yamashita, K.

1997-01-01

The High Temperature Engineering Test Reactor (HTTR) which is under construction by Japan Atomic Energy Research Institute (JAERI) is a graphite-moderated and helium gas-cooled reactor with an outlet temperature of 950 deg. C and a thermal output of 30MW. The first criticality is expected at the end of October 1997. The start-up physics tests (SPTs) are planned in the period from mid 1997 to the end of 1998. Characteristic items of the SPTs are: 1) Criticality approach; 2) Tests on a preliminary annual core; 3) Measurement of scram reactivity; 4) Excess reactivity test; 5) Measurements along with a 2-step-scram reactor shutdown procedure. (author)

Enhanced Verification Test Suite for Physics Simulation Codes

Energy Technology Data Exchange (ETDEWEB)

Kamm, J R; Brock, J S; Brandon, S T; Cotrell, D L; Johnson, B; Knupp, P; Rider, W; Trucano, T; Weirs, V G

2008-10-10

This document discusses problems with which to augment, in quantity and in quality, the existing tri-laboratory suite of verification problems used by Los Alamos National Laboratory (LANL), Lawrence Livermore National Laboratory (LLNL), and Sandia National Laboratories (SNL). The purpose of verification analysis is demonstrate whether the numerical results of the discretization algorithms in physics and engineering simulation codes provide correct solutions of the corresponding continuum equations. The key points of this document are: (1) Verification deals with mathematical correctness of the numerical algorithms in a code, while validation deals with physical correctness of a simulation in a regime of interest. This document is about verification. (2) The current seven-problem Tri-Laboratory Verification Test Suite, which has been used for approximately five years at the DOE WP laboratories, is limited. (3) Both the methodology for and technology used in verification analysis have evolved and been improved since the original test suite was proposed. (4) The proposed test problems are in three basic areas: (a) Hydrodynamics; (b) Transport processes; and (c) Dynamic strength-of-materials. (5) For several of the proposed problems we provide a 'strong sense verification benchmark', consisting of (i) a clear mathematical statement of the problem with sufficient information to run a computer simulation, (ii) an explanation of how the code result and benchmark solution are to be evaluated, and (iii) a description of the acceptance criterion for simulation code results. (6) It is proposed that the set of verification test problems with which any particular code be evaluated include some of the problems described in this document. Analysis of the proposed verification test problems constitutes part of a necessary--but not sufficient--step that builds confidence in physics and engineering simulation codes. More complicated test cases, including physics models of

Test-retest reliability of a questionnaire to assess physical environmental factors pertaining to physical activity

Directory of Open Access Journals (Sweden)

McGinn Aileen P

2005-06-01

Full Text Available Abstract Background Despite the documented benefits of physical activity, many adults do not obtain the recommended amounts. Barriers to physical activity occur at multiple levels, including at the individual, interpersonal, and environmental levels. Only until more recently has there been a concerted focus on how the physical environment might affect physical activity behavior. With this new area of study, self-report measures should be psychometrically tested before use in research studies. Therefore the objective of this study was to document the test-retest reliability of a questionnaire designed to assess physical environmental factors that might be associated with physical activity in a diverse adult population. Methods Test and retest surveys were conducted over the telephone with 106 African American and White women and men living in either Forsyth County, North Carolina or Jackson, Mississippi. Reliability of self-reported environmental factors across four domains (e.g., access to facilities and destinations, functionality and safety, aesthetics, natural environment was determined using intraclass correlation coefficients (ICC overall and separately by gender and race. Results Generally items displayed moderate and sometimes substantial reliability (ICC between 0.4 to 0.8, with a few differences by gender or race, across each of the domains. Conclusion This study provides some psychometric evidence for the use of many of these questions in studies examining the effect of self-reported physical environmental measures on physical activity behaviors, among African American and White women and men.

An objective measure of physical function of elderly outpatients. The Physical Performance Test.

Science.gov (United States)

Reuben, D B; Siu, A L

1990-10-01

Direct observation of physical function has the advantage of providing an objective, quantifiable measure of functional capabilities. We have developed the Physical Performance Test (PPT), which assesses multiple domains of physical function using observed performance of tasks that simulate activities of daily living of various degrees of difficulty. Two versions are presented: a nine-item scale that includes writing a sentence, simulated eating, turning 360 degrees, putting on and removing a jacket, lifting a book and putting it on a shelf, picking up a penny from the floor, a 50-foot walk test, and climbing stairs (scored as two items); and a seven-item scale that does not include stairs. The PPT can be completed in less than 10 minutes and requires only a few simple props. We then tested the validity of PPT using 183 subjects (mean age, 79 years) in six settings including four clinical practices (one of Parkinson's disease patients), a board-and-care home, and a senior citizens' apartment. The PPT was reliable (Cronbach's alpha = 0.87 and 0.79, interrater reliability = 0.99 and 0.93 for the nine-item and seven-item tests, respectively) and demonstrated concurrent validity with self-reported measures of physical function. Scores on the PPT for both scales were highly correlated (.50 to .80) with modified Rosow-Breslau, Instrumental and Basic Activities of Daily Living scales, and Tinetti gait score. Scores on the PPT were more moderately correlated with self-reported health status, cognitive status, and mental health (.24 to .47), and negatively with age (-.24 and -.18). Thus, the PPT also demonstrated construct validity. The PPT is a promising objective measurement of physical function, but its clinical and research value for screening, monitoring, and prediction will have to be determined.

ASTM test methods for composite characterization and evaluation

Science.gov (United States)

Masters, John E.

1994-01-01

A discussion of the American Society for Testing and Materials is given. Under the topic of composite materials characterization and evaluation, general industry practice and test methods for textile composites are presented.

The Physical Activity Scale for Individuals with Physical Disabilities: test-retest reliability and comparison with an accelerometer.

Science.gov (United States)

van der Ploeg, Hidde P; Streppel, Kitty R M; van der Beek, Allard J; van der Woude, Luc H V; Vollenbroek-Hutten, Miriam; van Mechelen, Willem

2007-01-01

The objective was to determine the test-retest reliability and criterion validity of the Physical Activity Scale for Individuals with Physical Disabilities (PASIPD). Forty-five non-wheelchair dependent subjects were recruited from three Dutch rehabilitation centers. Subjects' diagnoses were: stroke, spinal cord injury, whiplash, and neurological-, orthopedic- or back disorders. The PASIPD is a 7-d recall physical activity questionnaire that was completed twice, 1 wk apart. During this week, physical activity was also measured with an Actigraph accelerometer. The test-retest reliability Spearman correlation of the PASIPD was 0.77. The criterion validity Spearman correlation was 0.30 when compared to the accelerometer. The PASIPD had test-retest reliability and criterion validity that is comparable to well established self-report physical activity questionnaires from the general population.

A Novel Physical Sensing Principle for Liquid Characterization Using Paper-Based Hygro-Mechanical Systems (PB-HMS).

Science.gov (United States)

Perez-Cruz, Angel; Stiharu, Ion; Dominguez-Gonzalez, Aurelio

2017-07-20

In recent years paper-based microfluidic systems have emerged as versatile tools for developing sensors in different areas. In this work; we report a novel physical sensing principle for the characterization of liquids using a paper-based hygro-mechanical system (PB-HMS). The PB-HMS is formed by the interaction of liquid droplets and paper-based mini-structures such as cantilever beams. The proposed principle takes advantage of the hygroscopic properties of paper to produce hygro-mechanical motion. The dynamic response of the PB-HMS reveals information about the tested liquid that can be applied to characterize certain properties of liquids. A suggested method to characterize liquids by means of the proposed principle is introduced. The experimental results show the feasibility of such a method. It is expected that the proposed principle may be applied to sense properties of liquids in different applications where both disposability and portability are of extreme importance.

Evaluating College Students' Conceptual Knowledge of Modern Physics: Test of Understanding on Concepts of Modern Physics (TUCO-MP)

Science.gov (United States)

Akarsu, Bayram

2011-01-01

In present paper, we propose a new diagnostic test to measure students' conceptual knowledge of principles of modern physics topics. Over few decades since born of physics education research (PER), many diagnostic instruments that measure students' conceptual understanding of various topics in physics, the earliest tests developed in PER are Force…

U.S. Army Physical Demands Study: Development of the Occupational Physical Assessment Test for Combat Arms soldiers.

Science.gov (United States)

Foulis, Stephen A; Sharp, Marilyn A; Redmond, Jan E; Frykman, Peter N; Warr, Bradley J; Gebhardt, Deborah L; Baker, Todd A; Canino, Maria C; Zambraski, Edward J

2017-11-01

The United States Army sought to create a legally defensible, scientifically validated physical pre-employment screening test. The purpose of this study was to identify a single combination of predictor tests that would predict physical performance on all of the criterion measure task simulations relevant to the Combat Arms military occupational specialties. Concurrent validation. Data from 838 (608 males, 230 females) soldiers who completed both the criterion measure task simulations of a military occupational specialty and up to 14 predictor tests were used in the development of the test batteries. Stepwise regressions were used to identify test batteries that significantly predicted performance on the criterion measure task simulations of the military occupational specialties. Three test batteries were developed based on different subsets of the predictor tests: Test Battery 1 consisted of the medicine ball put, squat lift, beep test, standing long jump, and arm ergometer (adjusted R 2 =0.80-0.85, pTest Battery 2 consisted of the medicine ball put, squat lift, beep test, and standing long jump (adjusted R 2 =0.79-0.80, pTest Battery 3 consisted of the standing long jump, 1-minute push-ups, 1-minute sit-ups, 300m sprint, and Illinois agility test (adjusted R 2 =0.55-0.71, pTest Battery 2 was selected as the Army's Occupational Physical Assessment Test. It was highly predictive of performance of the Combat Arms military occupational specialties, required no complex equipment, and covered a range of physical fitness domains. Published by Elsevier Ltd.

Construct Validity of Physical Fitness Tests

Science.gov (United States)

2011-02-03

Powers, S. K., Lawler, J., Ayers, D., & Stuart, M. K. (1991). Physiological correlates to 800 meter running performance. Journal of Sports Medicine and... isokinetic tests. Journal of Sports Medicine and Physical Fitness, 36, 169-177. *Myers, D. C., Gebhardt, D. L., Crump, C.E., & Fleishman, E. A. (1984

The Physical Characterization of Liposome Salicylic Acid Using Transmission Electron Microscope

International Nuclear Information System (INIS)

Elman Panjaitan

2008-01-01

The physical characterization of liposome, formulated from salicylic acid using thin film hydration methods with cholesterol and soybean lecithin, has been done. The formula was characterized by optical microscopes and Transmission Electron Microscope (TEM). The observation result shows that the salicylic acid can be formulated to liposomes. Soybean lecithin combined with cholesterol (600 mg : 20 mg) was the best formula and the liposome was spherical vesicle like with dimension about 70 nm unit 800 nm. (author)

Municipal solid waste combustion: Fuel testing and characterization

Energy Technology Data Exchange (ETDEWEB)

Bushnell, D.J.; Canova, J.H.; Dadkhah-Nikoo, A.

1990-10-01

The objective of this study is to screen and characterize potential biomass fuels from waste streams. This will be accomplished by determining the types of pollutants produced while burning selected municipal waste, i.e., commercial mixed waste paper residential (curbside) mixed waste paper, and refuse derived fuel. These materials will be fired alone and in combination with wood, equal parts by weight. The data from these experiments could be utilized to size pollution control equipment required to meet emission standards. This document provides detailed descriptions of the testing methods and evaluation procedures used in the combustion testing and characterization project. The fuel samples will be examined thoroughly from the raw form to the exhaust emissions produced during the combustion test of a densified sample.

Physical and chemical characterization of bioaerosols - Implications for nucleation processes

Science.gov (United States)

Ariya, P. A.; Sun, J.; Eltouny, N. A.; Hudson, E. D.; Hayes, C. T.; Kos, G.

The importance of organic compounds in the oxidative capacity of the atmosphere, and as cloud condensation and ice-forming nuclei, has been recognized for several decades. Organic compounds comprise a significant fraction of the suspended matter mass, leading to local (e.g. toxicity, health hazards) and global (e.g. climate change) impacts. The state of knowledge of the physical chemistry of organic aerosols has increased during the last few decades. However, due to their complex chemistry and the multifaceted processes in which they are involved, the importance of organic aerosols, particularly bioaerosols, in driving physical and chemical atmospheric processes is still very uncertain and poorly understood. Factors such as solubility, surface tension, chemical impurities, volatility, morphology, contact angle, deliquescence, wettability, and the oxidation process are pivotal in the understanding of the activation processes of cloud droplets, and their chemical structures, solubilities and even the molecular configuration of the microbial outer membrane, all impact ice and cloud nucleation processes in the atmosphere. The aim of this review paper is to assess the current state of knowledge regarding chemical and physical characterization of bioaerosols with a focus on those properties important in nucleation processes. We herein discuss the potential importance (or lack thereof) of physical and chemical properties of bioaerosols and illustrate how the knowledge of these properties can be employed to study nucleation processes using a modeling exercise. We also outline a list of major uncertainties due to a lack of understanding of the processes involved or lack of available data. We will also discuss key issues of atmospheric significance deserving future physical chemistry research in the fields of bioaerosol characterization and microphysics, as well as bioaerosol modeling. These fundamental questions are to be addressed prior to any definite conclusions on the

Physics and engineering assessments of spherical torus component test facility

International Nuclear Information System (INIS)

Peng, Y.-K.M.; Neumeyer, C.A.; Kessel, C.; Rutherford, P.; Mikkelsen, D.; Bell, R.; Menard, J.; Gates, D.; Schmidt, J.; Synakowski, E.; Grisham, L.; Fogarty, P.J.; Strickler, D.J.; Burgess, T.W.; Tsai, J.; Nelson, B.E.; Sabbagh, S.; Mitarai, O.; Cheng, E.T.; El-Guebaly, L.

2005-01-01

A broadly based study of the fusion engineering and plasma science conditions of a Component Test Facility (CTF), using the Spherical Torus or Spherical Tokamak (ST) configuration, have been carried out. The chamber systems testing conditions in a CTF are characterized by high fusion neutron fluxes Γ n > 4.4x10 13 n/s/cm 2 , over size scales > 10 5 cm 2 and depth scales > 50 cm, delivering > 3 accumulated displacement per atom (dpa) per year. The desired chamber conditions can be provided by a CTF with R 0 1.2 m, A = 1.5, elongation ∼ 3.2, I p ∼ 9 MA, B T ∼ 2.5 T, producing a driven fusion burn using 36 MW of combined neutral beam and RF power. Relatively robust ST plasma conditions are adequate, which have been shown achievable [4] without active feedback manipulation of the MHD modes. The ST CTF will test the single-turn, copper alloy center leg for the toroidal field coil without an induction solenoid and neutron shielding, and require physics data on solenoid-free plasma current initiation, ramp-up, and sustainment to multiple MA level. A new systems code that combines the key required plasma and engineering science conditions of CTF has been prepared and utilized as part of this study. The results show high potential for a family of lowercost CTF devices to suit a variety of fusion engineering science test missions. (author)

Tests, measurements, and characterization of electro-optic devices and systems

International Nuclear Information System (INIS)

Wadekar, S.G.

1989-01-01

This book contains the proceedings on tests, measurements and characterization of electro-optic devices and systems. Topics covered include: Measurement of spectral dynamics in single-quantum-well lasers, High power computer controlled laser diode characterization tester, and Laser diode characterization instrumentation

Commissioning experience and beam physics measurements at the SwissFEL Injector Test Facility

Directory of Open Access Journals (Sweden)

T. Schietinger

2016-10-01

Full Text Available The SwissFEL Injector Test Facility operated at the Paul Scherrer Institute between 2010 and 2014, serving as a pilot plant and test bed for the development and realization of SwissFEL, the x-ray Free-Electron Laser facility under construction at the same institute. The test facility consisted of a laser-driven rf electron gun followed by an S-band booster linac, a magnetic bunch compression chicane and a diagnostic section including a transverse deflecting rf cavity. It delivered electron bunches of up to 200 pC charge and up to 250 MeV beam energy at a repetition rate of 10 Hz. The measurements performed at the test facility not only demonstrated the beam parameters required to drive the first stage of an FEL facility, but also led to significant advances in instrumentation technologies, beam characterization methods and the generation, transport and compression of ultralow-emittance beams. We give a comprehensive overview of the commissioning experience of the principal subsystems and the beam physics measurements performed during the operation of the test facility, including the results of the test of an in-vacuum undulator prototype generating radiation in the vacuum ultraviolet and optical range.

Start up physics tests of units 5 and 6 (WWER 1000) at Kozloduy NPP by comparison with the calculated neutron physics characteristics

International Nuclear Information System (INIS)

Antov, A.; Stoyanova, I.

2008-01-01

In conjunction with each refuelling shutdown of the reactor core, nuclear design calculations are performed to ensure that the reactor physics characteristics of the new core will be consistent with the safety limits. Prior to return to normal operation, a physics test program is required to determine if the operating characteristics of the core are consistent with the design predictions and to ensure that the core can be operated as designed. Successful completion of the physics test program is demonstrated when the test results agree with the predicted results within predetermined test criteria. Successful completion of the physics test program and successful completion of other tests, which are performed after each refuelling provides assurance that the plant can be operated as designed. The calculated neutron-physics characteristics values of Kozloduy NPP Unit 5 and Unit 6 (WWER 1000) obtained by the computer code package KASKAD are compared with the obtained results during the start up physics tests. The core fuel loading consists of 163 fuel assemblies (FAs). The calculated values are given according to actual experimental conditions of the reactor core during start up physics tests. The report includes comparisons between calculation results by code package KASKAD (BIPR7A) and experimental data values of main neutron-physics characteristics during start up physics tests in selected recent cycles of Kozloduy NPP Unit 5 and Unit 6. (authors)

Start up physics tests of Units 5 and 6 (WWER-1000) at Kozloduy NPP by comparison with the calculated neutron physics characteristics

International Nuclear Information System (INIS)

Stoyanova, I.; Antov, A.

2007-01-01

In conjunction with each refuelling shutdown of the reactor core, nuclear design calculations are performed to ensure that the reactor physics characteristics of the new core will be consistent with the safety limits. Prior to return to normal operation, a physics test program is required to determine if the operating characteristics of the core are consistent with the design predictions and to ensure that the core can be operated as designed. Successful completion of the physics test program is demonstrated when the test results agree with the predicted results within predetermined test criteria. Successful completion of the physics test program and successful completion of other tests which are performed after each refuelling provides assurance that the plant can be operated as designed. The calculated neutron-physics characteristics values of Kozloduy NPP Unit 5 and Unit 6 (WWER 1000) obtained by the computer code package KASKAD are compared with the obtained results during the start up physics tests. The core fuel loading consists of 163 fuel assemblies. The calculated values are given according to actual experimental conditions of the reactor core during start up physics tests. The report includes comparisons between calculation results by code package KASKAD (BIPR7A) and experimental data values of main neutron-physics characteristics during start up physics tests in selected recent cycles of Kozloduy NPP Unit 5 and Unit 6 (Authors)

Physical examination tests for hip dysfunction and injury.

Science.gov (United States)

Reiman, Michael P; Mather, Richard C; Cook, Chad E

2015-03-01

Physical examination tests for hip dysfunction and injury of the strongest diagnostic accuracy were identified in a recent systematic review with meta-analysis in BJSM. These tests are described in this article. A detailed description of the various different tests is given, with photographs for each test procedure. Diagnostic interpretation of each test requires careful consideration, with special attention to specific variables such as test performance and patient population. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Do it yourself: optical spectrometer for physics undergraduate instruction in nanomaterial characterization

International Nuclear Information System (INIS)

Nuryantini, Ade Yeti; Mahen, Ea Cahya Septia; Sawitri, Asti; Nuryadin, Bebeh Wahid

2017-01-01

In this paper, we report on a homemade optical spectrometer using diffraction grating and image processing techniques. This device was designed to produce spectral images that could then be processed by measuring signal strength (pixel intensity) to obtain the light source, transmittance, and absorbance spectra of the liquid sample. The homemade optical spectrometer consisted of: (i) a white LED as a light source, (ii) a cuvette or sample holder, (iii) a slit, (iv) a diffraction grating, and (v) a CMOS camera (webcam). In this study, various concentrations of a carbon nanoparticle (CNP) colloid were used in the particle size sample test. Additionally, a commercial optical spectrometer and tunneling electron microscope (TEM) were used to characterize the optical properties and morphology of the CNPs, respectively. The data obtained using the homemade optical spectrometer, commercial optical spectrometer, and TEM showed similar results and trends. Lastly, the calculation and measurement of CNP size were performed using the effective mass approximation (EMA) and TEM. These data showed that the average nanoparticle sizes were approximately 2.4 nm and 2.5 ± 0.3 nm, respectively. This research provides new insights into the development of a portable, simple, and low-cost optical spectrometer that can be used in nanomaterial characterization for physics undergraduate instruction. (paper)

Formulation and Physical Test of Ethanolic Extract Sambiloto Leaves (Andrographis paniculata Ointment

Directory of Open Access Journals (Sweden)

Indri Kusuma Dewi

2016-01-01

Full Text Available Introduction: Andrographis paniculata had known contained active substance such as andrographolida, atsiri oil, flavonoid, tannin, alkaloid, and saponin which functions as antibacterial, antitoxic, analgesic, and anti-pyretic. Based on its antibacterial properties, an ointment form of Andrographis paniculata leaf is then formulated, for practical usage. Ointment formula is semi solid for topical use in the skin or mucosal membranes. Objectives: to know the result of ointment physical test of etanolic extract Andrographis paniculata leaf. Methods: physical tests contain organoleptic test, pH, homogenity, adhesion test and dispersive test. Results: Ointment shaped semi solid, blacky green and special smell of Andrographis paniculata, pH 6, homogenity test obtained homogenous results, adhesion test was 82 second and dispersive test was 5.6 cm. Conclusion: the result of physical tests of etanolic Andrographis paniculata leaf extract ointment appropriate with quality standard.

Complex confining layers : a physical and geochemical characterization of heterogeneous unconsolidated fluvial deposits using a facies-based approach

NARCIS (Netherlands)

Helvoort, Pieter-Jan van

2003-01-01

A proper characterization of physical and chemical heterogeneities in the subsoil is an important condition for successful modeling of groundwater flow and solute transport. This study focuses on the physical and chemical characterization of a complex confining layer in the Rhine–Meuse deltaic plain

Characterizing, modeling, and addressing gender disparities in introductory college physics

Science.gov (United States)

Kost-Smith, Lauren Elizabeth

2011-12-01

The underrepresentation and underperformance of females in physics has been well documented and has long concerned policy-makers, educators, and the physics community. In this thesis, we focus on gender disparities in the first- and second-semester introductory, calculus-based physics courses at the University of Colorado. Success in these courses is critical for future study and careers in physics (and other sciences). Using data gathered from roughly 10,000 undergraduate students, we identify and model gender differences in the introductory physics courses in three areas: student performance, retention, and psychological factors. We observe gender differences on several measures in the introductory physics courses: females are less likely to take a high school physics course than males and have lower standardized mathematics test scores; males outscore females on both pre- and post-course conceptual physics surveys and in-class exams; and males have more expert-like attitudes and beliefs about physics than females. These background differences of males and females account for 60% to 70% of the gender gap that we observe on a post-course survey of conceptual physics understanding. In analyzing underlying psychological factors of learning, we find that female students report lower self-confidence related to succeeding in the introductory courses (self-efficacy) and are less likely to report seeing themselves as a "physics person". Students' self-efficacy beliefs are significant predictors of their performance, even when measures of physics and mathematics background are controlled, and account for an additional 10% of the gender gap. Informed by results from these studies, we implemented and tested a psychological, self-affirmation intervention aimed at enhancing female students' performance in Physics 1. Self-affirmation reduced the gender gap in performance on both in-class exams and the post-course conceptual physics survey. Further, the benefit of the self

Effects of Vigorous Intensity Physical Activity on Mathematics Test Performance

Science.gov (United States)

Phillips, David S.; Hannon, James C.; Castelli, Darla M.

2015-01-01

The effect of an acute bout of physical activity on academic performance in school-based settings is under researched. The purpose of this study was to examine associations between a single, vigorous (70-85%) bout of physical activity completed during physical education on standardized mathematics test performance among 72, eighth grade students…

Comments on Thermal Physical Properties Testing Methods of Phase Change Materials

Directory of Open Access Journals (Sweden)

Jingchao Xie

2013-01-01

Full Text Available There is no standard testing method of the thermal physical properties of phase change materials (PCM. This paper has shown advancements in this field. Developments and achievements in thermal physical properties testing methods of PCM were commented, including differential scanning calorimetry, T-history measurement, the water bath method, and differential thermal analysis. Testing principles, advantages and disadvantages, and important points for attention of each method were discussed. A foundation for standardized testing methods for PCM was made.

Reliable and sensitive physical testing of elite trapeze sailors

DEFF Research Database (Denmark)

Bay, Jonathan; Bojsen-Møller, Jens; Nordsborg, Nikolai Baastrup

2018-01-01

It was investigated, if a newly developed discipline specific test for elite-level trapeze sailors is reli-able and sensitive. Furthermore, the physical demands of trapeze sailing were examined. In part 1, nine national team athletes were accustomed to a simulated sailing test, which subsequently....... 265 ± 45W, Psailing was 54.5 ± 7.2% VO2max , 75.1 ± 3.1% HRmax and 5.8 ± 2.7 mM, respectively. However, VO2 and HR were substantially higher for periods of the race...... as peak values were 83.5 ± 11.4% and 89.9 ± 1.7% of max, respectively. In conclusion, the present test is reliable and sensitive, thus providing a sailing specific alternative to traditional physical testing of elite trapeze sailors. Additionally, on-water rac-ing requires moderate aerobic energy...

Applicability of slug interference testing of hydraulic characterization of contaminated aquifer sites

International Nuclear Information System (INIS)

Spane, F.A.; Swanson, L.C.

1993-10-01

Aquifer test methods available for characterizing hazardous waste sites are sometimes restricted because of problems with disposal of contaminated groundwater. These problems, in part, have made slug tests a more desirable method of determining hydraulic properties at such sites. However, in higher permeability formations (i.e., transmissivities ≥ 1 x 10 -3 m 2 /s), slug test results often cannot be analyzed and give, at best, only a lower limit for transmissivity. A need clearly exists to develop test methods that can be used to characterize higher permeability aquifers without removing large amounts of contaminated groundwater. One hydrologic test method that appears to hold promise for characterizing such sites is the slug interference test. To assess the applicability of this test method for use in shallow alluvial aquifer systems, slug interference tests have been conducted, along with more traditional aquifer testing methods, at several Hanford multiple-well sites. Transmissivity values estimated from the slug interference tests were comparable (within a factor of 2 to 3) to values calculated using traditional testing methods, and made it possible to calculate the storativity or specific yield for the intervening test formation. The corroboration of test results indicates that slug interference testing is a viable hydraulic characterization method in transmissive alluvial aquifers, and may represent one of the few test methods that can be used in sensitive areas where groundwater is contaminated

Characterizing pedagogical practices of university physics students in informal learning environments

Science.gov (United States)

Hinko, Kathleen A.; Madigan, Peter; Miller, Eric; Finkelstein, Noah D.

2016-06-01

[This paper is part of the Focused Collection on Preparing and Supporting University Physics Educators.] University educators (UEs) have a long history of teaching physics not only in formal classroom settings but also in informal outreach environments. The pedagogical practices of UEs in informal physics teaching have not been widely studied, and they may provide insight into formal practices and preparation. We investigate the interactions between UEs and children in an afterschool physics program facilitated by university physics students from the University of Colorado Boulder. In this program, physics undergraduates, graduate students, and postdoctoral researchers work with K-8 children on hands-on physics activities on a weekly basis over the course of a semester. We use an activity theoretic framework as a tool to examine situational aspects of individuals' behavior in the complex structure of the afterschool program. Using this framework, we analyze video of UE-child interactions and identify three main pedagogical modalities that UEs display during activities: instruction, consultation, and participation modes. These modes are characterized by certain language, physical location, and objectives that establish differences in UE-child roles and division of labor. Based on this analysis, we discuss implications for promoting pedagogical strategies through purposeful curriculum development and university educator preparation.

MULTI-ATTRIBUTE SEISMIC/ROCK PHYSICS APPROACH TO CHARACTERIZING FRACTURED RESERVOIRS

Energy Technology Data Exchange (ETDEWEB)

Gary Mavko

2000-10-01

This project consists of three key interrelated Phases, each focusing on the central issue of imaging and quantifying fractured reservoirs, through improved integration of the principles of rock physics, geology, and seismic wave propagation. This report summarizes the results of Phase I of the project. The key to successful development of low permeability reservoirs lies in reliably characterizing fractures. Fractures play a crucial role in controlling almost all of the fluid transport in tight reservoirs. Current seismic methods to characterize fractures depend on various anisotropic wave propagation signatures that can arise from aligned fractures. We are pursuing an integrated study that relates to high-resolution seismic images of natural fractures to the rock parameters that control the storage and mobility of fluids. Our goal is to go beyond the current state-of-the art to develop and demonstrate next generation methodologies for detecting and quantitatively characterizing fracture zones using seismic measurements. Our study incorporates 3 key elements: (1) Theoretical rock physics studies of the anisotropic viscoelastic signatures of fractured rocks, including up scaling analysis and rock-fluid interactions to define the factors relating fractures in the lab and in the field. (2) Modeling of optimal seismic attributes, including offset and azimuth dependence of travel time, amplitude, impedance and spectral signatures of anisotropic fractured rocks. We will quantify the information content of combinations of seismic attributes, and the impact of multi-attribute analyses in reducing uncertainty in fracture interpretations. (3) Integration and interpretation of seismic, well log, and laboratory data, incorporating field geologic fracture characterization and the theoretical results of items 1 and 2 above. The focal point for this project is the demonstration of these methodologies in the Marathon Oil Company Yates Field in West Texas.

Soil washing physical separations test procedure - 300-FF-1 operable unit

Energy Technology Data Exchange (ETDEWEB)

Belden, R.D.

1993-10-08

This procedure provides the operations approach, a field sampling plan, and laboratory procedures for a soil washing test to be conducted by Alternative Remedial Technologies, Inc. (ART) in the 300-FF-1 area at the Hanford site. The {open_quotes}Quality Assurance Project Plan for the Soil Washing Physical Separations Test, 300-FF-1 Operable Unit,{close_quotes} Hanford, Washington, Alternative Remedial Technologies, Inc., February 1994 (QAPP) is provided in a separate document that presents the procedural and organizational guidelines for this test. This document describes specifications, responsibilities, and general procedures to be followed to conduct physical separation soil treatability tests in the North Process Pond of the 300-FF-1 Operable Unit (OU) at the Hanford Site. These procedures are based on the {open_quotes}300-FF-1 Physical Separations CERCLA Treatability Test Plan, DOE/RL 92-2l,{close_quotes} (DOE-RL 1993).

Soil washing physical separations test procedure - 300-FF-1 operable unit

International Nuclear Information System (INIS)

Belden, R.D.

1993-01-01

This procedure provides the operations approach, a field sampling plan, and laboratory procedures for a soil washing test to be conducted by Alternative Remedial Technologies, Inc. (ART) in the 300-FF-1 area at the Hanford site. The open-quotes Quality Assurance Project Plan for the Soil Washing Physical Separations Test, 300-FF-1 Operable Unit,close quotes Hanford, Washington, Alternative Remedial Technologies, Inc., February 1994 (QAPP) is provided in a separate document that presents the procedural and organizational guidelines for this test. This document describes specifications, responsibilities, and general procedures to be followed to conduct physical separation soil treatability tests in the North Process Pond of the 300-FF-1 Operable Unit (OU) at the Hanford Site. These procedures are based on the open-quotes 300-FF-1 Physical Separations CERCLA Treatability Test Plan, DOE/RL 92-2l,close quotes (DOE-RL 1993)

Benchmark physics tests in the metallic-fuelled assembly ZPPR-15

International Nuclear Information System (INIS)

McFarlane, H.F.; Brumbach, S.B.; Carpenter, S.G.; Collins, P.J.

1987-01-01

In the last two years a shift in emphasis to inherent safety and economic competitiveness has led to a resurgence in US interest in metallic-alloy fuels for LMRs. Argonne National Laboratory initiated an extensive testing program for metallic-fuelled LMR technology that has included benchmark physics as one component. The tests done in the ZPPR-15 Program produced the first physics results in over 20 years for a metal-composition LMR core

Pre-flight physical simulation test of HIMES reentry test vehicle

Science.gov (United States)

Kawaguchi, Jun'ichiro; Inatani, Yoshifumi; Yonemoto, Koichi; Hosokawa, Shigeru

ISAS is now developing a small reentry test vehicle, which is 2m long with a 1.5m wing span and weighs about 170 kg, for the purpose of exploring high angle-of-attack aerodynamic attitude control issue in supersonic and hypersonic speed. The flight test, employing 'Rockoon' launch system, is planned as a preliminary design verification for a fully reusable winged rocket named HIMES (Highly Maneuverable Experimental Space) vehicle. This paper describes the results of preflight ground test using a motion table system. This ground system test is called 'physical simulation' aimed at: (1) functional verification of side-jet system, aerodynamic surface actuators, battery and onboard avionics; and (2) guidance and control law evaluation, in total hardware-in-the-loop system. The pressure of side-jet nozzles was measured to provide exact thrust characteristics of reaction control. The dynamics of vehicle motion was calculated in real-time by the ground simulation computer.

A simulated test of physical starting and reactor physics on zero power facility of PWR

International Nuclear Information System (INIS)

Yao Zewu; Ji Huaxiang; Chen Zhicheng; Yao Zhiquan; Chen Chen; Li Yuwen

1995-01-01

The core neutron economics has been verified through experiments conducted at a zero power reactor with baffles of various thickness. A simulated test of physical starting of Qinshan PWR has been introduced. The feasibility and safety of the programme are verified. The research provides a valuable foundation for developing physical starting programme

Fabrication and characterization of absorber pellets for FFTF irradiation testing

International Nuclear Information System (INIS)

Wilson, C.N.; Hollenberg, G.W.

1981-01-01

Methods used for characterization of B 4 C powder and fabricated pellets are summarized. Fabrication techniques used at HEDL for absorber test pellets are reviewed and selected powder and pellet characterization data are presented

A physical function test for use in the intensive care unit: validity, responsiveness, and predictive utility of the physical function ICU test (scored).

Science.gov (United States)

Denehy, Linda; de Morton, Natalie A; Skinner, Elizabeth H; Edbrooke, Lara; Haines, Kimberley; Warrillow, Stephen; Berney, Sue

2013-12-01

Several tests have recently been developed to measure changes in patient strength and functional outcomes in the intensive care unit (ICU). The original Physical Function ICU Test (PFIT) demonstrates reliability and sensitivity. The aims of this study were to further develop the original PFIT, to derive an interval score (the PFIT-s), and to test the clinimetric properties of the PFIT-s. A nested cohort study was conducted. One hundred forty-four and 116 participants performed the PFIT at ICU admission and discharge, respectively. Original test components were modified using principal component analysis. Rasch analysis examined the unidimensionality of the PFIT, and an interval score was derived. Correlations tested validity, and multiple regression analyses investigated predictive ability. Responsiveness was assessed using the effect size index (ESI), and the minimal clinically important difference (MCID) was calculated. The shoulder lift component was removed. Unidimensionality of combined admission and discharge PFIT-s scores was confirmed. The PFIT-s displayed moderate convergent validity with the Timed "Up & Go" Test (r=-.60), the Six-Minute Walk Test (r=.41), and the Medical Research Council (MRC) sum score (rho=.49). The ESI of the PFIT-s was 0.82, and the MCID was 1.5 points (interval scale range=0-10). A higher admission PFIT-s score was predictive of: an MRC score of ≥48, increased likelihood of discharge home, reduced likelihood of discharge to inpatient rehabilitation, and reduced acute care hospital length of stay. Scoring of sit-to-stand assistance required is subjective, and cadence cutpoints used may not be generalizable. The PFIT-s is a safe and inexpensive test of physical function with high clinical utility. It is valid, responsive to change, and predictive of key outcomes. It is recommended that the PFIT-s be adopted to test physical function in the ICU.

Blind Test of Physics-Based Prediction of Protein Structures

Science.gov (United States)

Shell, M. Scott; Ozkan, S. Banu; Voelz, Vincent; Wu, Guohong Albert; Dill, Ken A.

2009-01-01

We report here a multiprotein blind test of a computer method to predict native protein structures based solely on an all-atom physics-based force field. We use the AMBER 96 potential function with an implicit (GB/SA) model of solvation, combined with replica-exchange molecular-dynamics simulations. Coarse conformational sampling is performed using the zipping and assembly method (ZAM), an approach that is designed to mimic the putative physical routes of protein folding. ZAM was applied to the folding of six proteins, from 76 to 112 monomers in length, in CASP7, a community-wide blind test of protein structure prediction. Because these predictions have about the same level of accuracy as typical bioinformatics methods, and do not utilize information from databases of known native structures, this work opens up the possibility of predicting the structures of membrane proteins, synthetic peptides, or other foldable polymers, for which there is little prior knowledge of native structures. This approach may also be useful for predicting physical protein folding routes, non-native conformations, and other physical properties from amino acid sequences. PMID:19186130

Testing fundamental physics with gravitational waves

CERN Multimedia

CERN. Geneva

2017-01-01

The landmark detection of gravitational waves (GWs) has opened a new era in physics, giving access to the hitherto unexplored strong-gravity regime, where spacetime curvature is extreme and the relevant speed is close to the speed of light. In parallel to its countless astrophysical applications, this discovery can have also important implications for fundamental physics. In this context, I will discuss some outstanding, cross-cutting problems that can be finally investigated in the GW era: the nature of black holes and of spacetime singularities, the limits of classical gravity, the existence of extra light fields, and the effects of dark matter near compact objects. Future GW measurements will provide unparalleled tests of quantum-gravity effects at the horizon scale, exotic compact objects, ultralight dark matter, and of general relativity in the strong-field regime.

Dynamic MTF, an innovative test bench for detector characterization

Science.gov (United States)

Emmanuel, Rossi; Raphaël, Lardière; Delmonte, Stephane

2017-11-01

PLEIADES HR are High Resolution satellites for Earth observation. Placed at 695km they reach a 0.7m spatial resolution. To allow such performances, the detectors are working in a TDI mode (Time and Delay Integration) which consists in a continuous charge transfer from one line to the consecutive one while the image is passing on the detector. The spatial resolution, one of the most important parameter to test, is characterized by the MTF (Modulation Transfer Function). Usually, detectors are tested in a staring mode. For a higher level of performances assessment, a dedicated bench has been set-up, allowing detectors' MTF characterization in the TDI mode. Accuracy and reproducibility are impressive, opening the door to new perspectives in term of HR imaging systems testing.

DARPA Antibody Technology Program. Standardized Test Bed for Antibody Characterization: Characterization of an MS2 ScFv Antibody Produced by Illumina

Science.gov (United States)

2016-08-01

ECBC-TR-1395 DARPA ANTIBODY TECHNOLOGY PROGRAM STANDARDIZED TEST BED FOR... ANTIBODY CHARACTERIZATION: CHARACTERIZATION OF AN MS2 SCFV ANTIBODY PRODUCED BY ILLUMINA Patricia E. Buckley Alena M. Calm Heather Welsh Roy...4. TITLE AND SUBTITLE DARPA Antibody Technology Program Standardized Test Bed for Antibody Characterization: Characterization of an MS2 ScFv

Physical Characterization of Solid-Liquid Slurries at High Weight Fractions Using Optical and Ultrasonic Methods

International Nuclear Information System (INIS)

Burgess, L.W.; Brodsky, A.M.; Panetta P.D.

2005-01-01

Remediation of highly radioactive waste is a major technical and programmatic challenge for the DOE. Rapid, on-line physical characterization of highly concentrated slurries is required for the safe and efficient remediation of 90 million gallons of high level radioactive waste (HLW), sodium bearing waste, and mixed waste. The research presented here, describes a collaborative effort between Pacific Northwest National Laboratory (PNNL) and the University of Washington (UW) to directly address the need for rapid on-line characterization of the physical properties of HLW slurries during all phases of the remediation process, from in-tank characterization of sediments to monitoring of the concentration, particle size, and degree of agglomeration and gelation of slurries during transport. Near-surface characterization of the slurry flow in the particle size range from nanometer to micrometer is examined using optical low coherence reflectometry. Volumetric characterization at depths in the slurry flow, up to several centimeters in the particle size range from the micrometer to millimeter, is realized by utilizing ultrasonic backscatter and diffuses fields. One of the strengths, the teaming up of significant talents in both experimental and theoretical optics and in ultrasonics, provides a synergistic approach to integrate these complimentary techniques. One of the benefits of this combined approach is the physical characterization of HLW over a concentration and particle size range that is broader than can be achieved with today's technology. This will avoid a costly increase in waste stream volume due to excess dilution, and will lessen chance of plugging pipes that could shut down expensive processing lines

Project Physics Tests 4, Light and Electromagnetism.

Science.gov (United States)

Harvard Univ., Cambridge, MA. Harvard Project Physics.

Test items relating to Project Physics Unit 4 are presented in this booklet. Included are 70 multiple-choice and 22 problem-and-essay questions. Concepts of light and electromagnetism are examined on charges, reflection, electrostatic forces, electric potential, speed of light, electromagnetic waves and radiations, Oersted's and Faraday's work,…

Test on the reactor with the portable digital reactivity meter for physical experiment

International Nuclear Information System (INIS)

Huang Liyuan

2010-01-01

Test must be performed on the zero power reactor During the development of portable digital reactivity meter for physical experiment, in order to check its measurement function and accuracy. It describes the test facility, test core, test methods, test items and test results. The test results show that the instrument satisfy the requirements of technical specification, and satisfy the reactivity measurement in the physical experiments on reactors. (authors)

Detailed Geophysical Fault Characterization in Yucca Flat, Nevada Test Site, Nevada

Energy Technology Data Exchange (ETDEWEB)

Theodore H. Asch; Donald Sweetkind; Bethany L. Burton; Erin L. Wallin

2009-02-10

Yucca Flat is a topographic and structural basin in the northeastern part of the Nevada Test Site (NTS) in Nye County, Nevada. Between the years 1951 and 1992, 659 underground nuclear tests took place in Yucca Flat; most were conducted in large, vertical excavations that penetrated alluvium and the underlying Cenozoic volcanic rocks. Radioactive and other potential chemical contaminants at the NTS are the subject of a long-term program of investigation and remediation by the U.S. Department of Energy (DOE), National Nuclear Security Administration, Nevada Site Office, under its Environmental Restoration Program. As part of the program, the DOE seeks to assess the extent of contamination and to evaluate the potential risks to humans and the environment from byproducts of weapons testing. To accomplish this objective, the DOE Environmental Restoration Program is constructing and calibrating a ground-water flow model to predict hydrologic flow in Yucca Flat as part of an effort to quantify the subsurface hydrology of the Nevada Test Site. A necessary part of calibrating and evaluating a model of the flow system is an understanding of the location and characteristics of faults that may influence ground-water flow. In addition, knowledge of fault-zone architecture and physical properties is a fundamental component of the containment of the contamination from underground nuclear tests, should such testing ever resume at the Nevada Test Site. The goal of the present investigation is to develop a detailed understanding of the geometry and physical properties of fault zones in Yucca Flat. This study was designed to investigate faults in greater detail and to characterize fault geometry, the presence of fault splays, and the fault-zone width. Integrated geological and geophysical studies have been designed and implemented to work toward this goal. This report describes the geophysical surveys conducted near two drill holes in Yucca Flat, the data analyses performed, and the

Advanced testing and characterization of transportation soils and bituminous sands

CSIR Research Space (South Africa)

Anochie-Boateng, Joseph

2007-12-01

Full Text Available This research study was intended to develop laboratory test procedures for advance testing and characterization of fine-grained cohesive soils and oil sand materials. The test procedures are based on typical field loading conditions and the loading...

Project Physics Tests 1, Concepts of Motion.

Science.gov (United States)

Harvard Univ., Cambridge, MA. Harvard Project Physics.

Test items relating to Project Physics Unit 1 are presented in this booklet, consisting of 70 multiple-choice and 20 problem-and-essay questions. Concepts of motion are examined with respect to velocities, acceleration, forces, vectors, Newton's laws, and circular motion. Suggestions are made for time consumption in answering some items. Besides…

The individual gamma dosemeter MD 20: Physical tests and evaluation tests

International Nuclear Information System (INIS)

Laureana, R.

1981-03-01

Tests on the digital individual dose ratemeter type DM 20 for gamma radiation measurement are presented. The aim of this testing is an evaluation of main physical characteristics under irradiation. Results are given in tables and graphs. Relative sensitivity versus dose rate is better than +14% for cobalt 60 photons with a good linearity. There is no detector saturation until 400 to 450 rad/h. The energy response is lower than +- 20% between 160 keV to 1.25 MeV. Autonomy is over 4000 hours. All informations: dose, dose rate and good working conditions are directly read [fr

Characterization and durability testing of a glass-bonded ceramic waste form

International Nuclear Information System (INIS)

Johnson, S. G.

1998-01-01

Argonne National Laboratory is developing a glass bonded ceramic waste form for encapsulating the fission products and transuranics from the conditioning of metallic reactor fuel. This waste form is currently being scaled to the multi-kilogram size for encapsulation of actual high level waste. This paper will present characterization and durability testing of the ceramic waste form. An emphasis on results from application of glass durability tests such as the Product Consistency Test and characterization methods such as X-ray diffraction and scanning electron microscopy. The information presented is based on a suite of tests utilized for assessing product quality during scale-up and parametric testing

Characterization testing of a 40 AHR bipolar nickel-hydrogen battery

Science.gov (United States)

Brewer, Jeffrey C.; Manzo, Michelle A.; Gemeiner, Russel P.

1989-01-01

Extensive characterization testing has been done on a second 40 amp-hour (Ahr), 10-cell bipolar nickel-hydrogen (Ni-H2) battery to study the effects of such operating parameters as charge and discharge rates, temperature, and pressure, on capacity, Ahr and watt-hour (Whr) efficiencies, end-of-charge (EOC) and mid-point discharge voltages. Testing to date has produced many interesting results, with the battery performing well throughout all of the test matrix except during the high-rate (5C and 10C) discharges, where poorer than expected results were observed. The exact cause of this poor performance is, as yet, unknown. Small scale 2 x 2 inch battery tests are to be used in studying this problem. Low earth orbit (LEO) cycle life testing at a 40 percent depth of discharge (DOD) and 10 C is scheduled to follow the characterization testing.

Digital Platform for Wafer-Level MEMS Testing and Characterization Using Electrical Response

Directory of Open Access Journals (Sweden)

Nuno Brito

2016-09-01

Full Text Available The uniqueness of microelectromechanical system (MEMS devices, with their multiphysics characteristics, presents some limitations to the borrowed test methods from traditional integrated circuits (IC manufacturing. Although some improvements have been performed, this specific area still lags behind when compared to the design and manufacturing competencies developed over the last decades by the IC industry. A complete digital solution for fast testing and characterization of inertial sensors with built-in actuation mechanisms is presented in this paper, with a fast, full-wafer test as a leading ambition. The full electrical approach and flexibility of modern hardware design technologies allow a fast adaptation for other physical domains with minimum effort. The digital system encloses a processor and the tailored signal acquisition, processing, control, and actuation hardware control modules, capable of the structure position and response analysis when subjected to controlled actuation signals in real time. The hardware performance, together with the simplicity of the sequential programming on a processor, results in a flexible and powerful tool to evaluate the newest and fastest control algorithms. The system enables measurement of resonant frequency (Fr, quality factor (Q, and pull-in voltage (Vpi within 1.5 s with repeatability better than 5 ppt (parts per thousand. A full-wafer with 420 devices under test (DUTs has been evaluated detecting the faulty devices and providing important design specification feedback to the designers.

The Physical Activity Scale for Individuals with Physical Disabilities : test-retest reliability and comparison with an accelerometer

NARCIS (Netherlands)

van der Ploeg, Hidde P; Streppel, Kitty R M; van der Beek, Allard J; van der Woude, Luc H V; Vollenbroek-Hutten, Miriam; van Mechelen, Willem; van der Woude, Lucas

BACKGROUND: The objective was to determine the test-retest reliability and criterion validity of the Physical Activity Scale for Individuals with Physical Disabilities (PASIPD). METHODS: Forty-five non-wheelchair dependent subjects were recruited from three Dutch rehabilitation centers. Subjects'

Tests and measures used by specialist physical therapists when examining patients with stroke.

Science.gov (United States)

Andrews, A Williams; Folger, Stephen E; Norbet, Shannon E; Swift, Lindsay C

2008-09-01

Examination procedures preferred by physical therapists have not been documented either specifically or comprehensively. The purpose of this study was to determine which tests and measures are used most frequently by specialists in the examination of adults with stroke. Physical therapy specialists were identified as having geriatric or neurologic certification through the American Board of Physical Therapy Specialties. A request to participate in a Web-based survey was sent to 471 individuals in the American Physical Therapy Association's Directory of Certified Specialists. A comprehensive list of tests and measures was first derived from the Interactive Guide to Physical Therapist Practice. The list was finalized based on several exclusion criteria and the results of a pilot study. Subjects rated the frequency of use of 294 tests and measures with patients post-stroke on a Likert scale. The survey response rate was 31.7% (n = 128). The 50 most frequently used tests and measures were identified. The results of this study do not identify the tests and measures that clinicians should use, only those that the specialists use. Nevertheless, clinicians may want to consider tests and measurements frequently used by specialists when examining adults with stroke.

RHIC Sextant Test -- Physics and performance

International Nuclear Information System (INIS)

Wei, J.; Fischer, W.; Ahrens, L.

1997-01-01

This paper presents beam physics and machine performance results of the Relativistic Heavy Ion Collider (RHIC) Sextant and AGS-to-RHIC (AtR) transfer line during the Sextant Test in early 1997. Techniques used to measure both machine properties (difference orbits, dispersion, and beamline optics) and beam parameters (energy, intensity, transverse and longitudinal emittances) are described. Good agreement was achieved between measured and design lattice optics. The gold ion beam quality was shown to approach RHIC design requirements

Mechanical characterization tests of the X2-Gen fuel assembly and skeleton

International Nuclear Information System (INIS)

Kim, Hyung Kyu; Yoon, Kyung Ho; Lee, Kang Hee; Kim, Jae Yong; Lee, Young Ho; Kang, Heung Seok

2011-01-01

The KNF (KEPCO Nuclear Fuel) requested mechanical characterization tests of a fuel assembly and a skeleton of the X2-Gen fuel. The tests consisted of the lateral vibration and lateral/axial stiffness, lateral/axial impact and combined deflection tests carried out by using the FAMeCT (Fuel Assembly Mechanical Characterization Tester) in KAERI. The upper and lower core plate simulators were newly designed and manufactured because the fuel geometry of the X2-Gen was different from the KSNP type fuel assembly. In addition to this, the upper carriage was also revised with the LM guide system from the previous two guide rods system. Therefore, the axial and combined deflection tests were soundly executed. Each test was repeated twice to confirm the repeatability. The discrepancy from the repetition was small enough to be neglected. The mechanical characterization tests were accredited with the KOLAS (Korea Laboratory Accreditation Scheme) standard, and the certified test reports (lateral vibration, lateral/axial bending and lateral/axial impact) and the uncertified test report (combined deflection) were issued together with the current test result report

Differences in gender performance on competitive physics selection tests

Science.gov (United States)

Wilson, Kate; Low, David; Verdon, Matthew; Verdon, Alix

2016-12-01

[This paper is part of the Focused Collection on Gender in Physics.] We have investigated gender differences in performance over the past eight years on the Australian Science Olympiad Exam (ASOE) for physics, which is taken by nearly 1000 high school students each year. The ASOE, run by Australian Science Innovations (ASI), is the initial stage of the process of selection of teams to represent Australia at the Asian and International Physics Olympiads. Students taking the exam are generally in their penultimate year of school and selected by teachers as being high performing in physics. Together with the overall differences in facility, we have investigated how the content and presentation of multiple-choice questions (MCQs) affects the particular answers selected by male and female students. Differences in the patterns of responses by male and female students indicate that males and females might be modeling situations in different ways. Some strong patterns were found in the gender gaps when the questions were categorized in five broad dimensions: content, process required, difficulty, presentation, and context. Almost all questions saw male students performing better, although gender differences were relatively small for questions with a more abstract context. Male students performed significantly better on most questions with a concrete context, although notable exceptions were found, including two such questions where female students performed better. Other categories that showed consistently large gaps favoring male students include questions with projectile motion and other two-dimensional motion or forces content, and processes involving interpreting diagrams. Our results have important implications, suggesting that we should be able to reduce the gender gaps in performance on MCQ tests by changing the way information is presented and setting questions in contexts that are less likely to favor males over females. This is important as MCQ tests are

Characterization of spent fuel approved testing material: ATM-106

International Nuclear Information System (INIS)

Guenther, R.J.; Blahnik, D.E.; Campbell, T.K.; Jenquin, U.P.; Mendel, J.E.; Thornhill, C.K.

1988-10-01

The characterization data obtained to date are described for Approved Testing Material (ATM)-106 spent fuel from Assembly BT03 of pressurized-water reactor Calvert Cliffs No. 1. This report is one in a series being prepared by the Materials Characterization Center at Pacific Northwest Laboratory on spent fuel ATMs. The ATMs are receiving extensive examinations to provide a source of well- characterized spent fuel for testing in the US Department of Energy Office of Civilian Radioactive Waste Management (OCWRM) program. ATM-106 consists of 20 full-length irradiated fuel rods with rod-average burnups of about 3700 GJ/kgM (43 MWd/kgM) and expected fission gas release of /approximately/10%. Characterization data include (1) as-fabricated fuel design, irradiation history, and subsequent storage and handling; (2) isotopic gamma scans; (3) fission gas analyses; (4) ceramography of the fuel and metallography of the cladding; (5) calculated nuclide inventories and radioactivities in the fuel and cladding; and (6) radiochemical analyses of the fuel and cladding. Additional analyses of the fuel rod are being conducted and will be included in planned revisions of this report. 12 refs., 110 figs., 81 tabs

Physical examination tests for the diagnosis of femoroacetabular impingement. A systematic review.

Science.gov (United States)

Pacheco-Carrillo, Aitana; Medina-Porqueres, Ivan

2016-09-01

Numerous clinical tests have been proposed to diagnose FAI, but little is known about their diagnostic accuracy. To summarize and evaluate research on the accuracy of physical examination tests for diagnosis of FAI. A search of the PubMed, SPORTDiscus and CINAHL databases was performed. Studies were considered eligible if they compared the results of physical examination tests to those of a reference standard. Methodological quality and internal validity assessment was performed by two independent reviewers using the Quality Assessment of Diagnostic Accuracy Studies (QUADAS) tool. The systematic search strategy revealed 298 potential articles, five of which articles met the inclusion criteria. After assessment using the QUADAS score, four of the five articles were of high quality. Clinical tests included were Impingement sign, IROP test (Internal Rotation Over Pressure), FABER test (Flexion-Abduction-External Rotation), Stinchfield/RSRL (Resisted Straight Leg Raise) test, Scour test, Maximal squat test, and the Anterior Impingement test. IROP test, impingement sign, and FABER test showed the most sensitive values to identify FAI. The diagnostic accuracy of physical examination tests to assess FAI is limited due to its heterogenecity. There is a strong need for sound research of high methodological quality in this area. Copyright © 2016 Elsevier Ltd. All rights reserved.

Challenges in Physical Characterization of Dim Space Objects: What Can We Learn from NEOs

Science.gov (United States)

Reddy, V.; Sanchez, J.; Thirouin, A.; Rivera-Valentin, E.; Ryan, W.; Ryan, E.; Mokovitz, N.; Tegler, S.

2016-09-01

Physical characterization of dim space objects in cis-lunar space can be a challenging task. Of particular interest to both natural and artificial space object behavior scientists are the properties beyond orbital parameters that can uniquely identify them. These properties include rotational state, size, shape, density and composition. A wide range of observational and non-observational factors affect our ability to characterize dim objects in cis-lunar space. For example, phase angle (angle between Sun-Target-Observer), temperature, rotational variations, temperature, and particle size (for natural dim objects). Over the last two decades, space object behavior scientists studying natural dim objects have attempted to quantify and correct for a majority of these factors to enhance our situational awareness. These efforts have been primarily focused on developing laboratory spectral calibrations in a space-like environment. Calibrations developed correcting spectral observations of natural dim objects could be applied to characterizing artificial objects, as the underlying physics is the same. The paper will summarize our current understanding of these observational and non-observational factors and present a case study showcasing the state of the art in characterization of natural dim objects.

The Entrance test of physics and Workbook in teaching of physics at secondary vocational school within long-term pedagogical research

Science.gov (United States)

Kerlínová, Věra

2017-01-01

Within the long-term pedagogical research ongoing since the school year 2008/2009 to 2015/2016 at the secondary vocational school in Bohumín was through of Entrance test of physics, which included curriculum of the sixth to ninth year of elementary school, regularly finding out, in which parts of Entrance test - Unit conversions, International System of Units, Properties of matter, Mechanics, Thermodynamics, Electricity and Magnetism, Optics, Atoms and Universe - pupils of the 1st years of secondary vocational school, technical and non-technical, reach a higher number of correct answers, in which dominates the wrong answers and which parts of the test pupils are better left out completely. It turned out that the results of these tests are very informative not only for theoretical and practical teaching, but also technical and other science subjects. The results of the Entrance tests are also a valuable source of information for continuous innovation Workbook of Physics - Mechanics for the 1st year of secondary vocational schools [1] - whose the first version began during the school year 2007/2008 and which was tested within pre-research in school years 2008/2009, 2009/2010 and within research in school year 2010/2011. On the basis of feedbacks getting from research the Workbook is regularly expanded, innovated and updated. The Workbook consists of parts dedicated to physical concepts, physical tasks, proposals to physical experiments, pupils comments from viewed video projection and documentary films, examples from the world of science and technology, examples from practice and real life, physical terminology in English, quizzes, competitions, interesting things and links related to discussed curriculum. The Workbook is divided into thematic sections, chapters and subchapters similar as physics textbooks for pupils of the 1st years of Secondary Schools in the Czech Republic. In the Workbook there are included tasks on fill in the words, polynomial tasks with

Prevalence and Correlates of Physical Fitness Testing in U.S. Schools--2000

Science.gov (United States)

Morrow, James R., Jr.; Fulton, Janet E.; Brener, Nancy D.; Kohl, Harold W., III

2008-01-01

Because of the perceived lack of youth physical fitness and/or concerns for increased obesity, physical education teachers are interested in youth fitness and physical activity levels. Statewide mandates are being developed that require school-based teachers to complete physical fitness testing. Data from the nationally representative School…

Physical Mapping Technologies for the Identification and Characterization of Mutated Genes to Crop Quality

International Nuclear Information System (INIS)

2011-09-01

The improvement of quality traits in food and industrial crops is an important breeding objective for both developed and developing countries in order to add value to the crop and thereby increasing farmers' income. It has been well established that the application of mutagens can be a very important approach for manipulating many crop characteristics including quality. While mutation induction using nuclear techniques such as gamma irradiation is a power tool in generating new genotypes with favourable alleles for improving crop quality in plant breeding, a more thorough understanding of gene expression, gene interactions, and physical location will improve ability to manipulate and control genes, and directly lead to crop improvement. Physical mapping technologies, molecular markers and molecular cytogenetic techniques are tools available with the potential to enhance the ability to tag genes and gene complexes to facilitate the selection of desirable genotypes in breeding programmes, including those based on mutation breeding. This Coordinated Research Project (CRP) on 'Physical Mapping Technologies for the Identification and Characterization of Mutated Genes Contributing to Crop Quality' was conducted under the overall IAEA project objective of 'Identification, Characterization and Transfer of Mutated Genes'. The specific objectives of the CRP were to assist Member States in accelerating crop breeding programmes through the application of physical mapping and complementary genomic approaches, and the characterization and utilization of induced mutants for improvement of crop quality. The IAEA-TECDOC describes the success obtained in the application of molecular cytology, molecular markers, physical mapping and mutation technologies since the inception of the CRP in 2003. The CRP also resulted in two book chapters, 35 peer reviewed papers, 25 conference proceedings, one PhD thesis, and 22 published abstracts. In addition, thirteen sequences were submitted to the

Physical Activity and Cervical Cancer Testing among American Indian Women

Science.gov (United States)

Muus, Kyle J.; Baker-Demaray, Twyla B.; Bogart, T. Andy; Duncan, Glen E.; Jacobsen, Clemma; Buchwald, Dedra S.; Henderson, Jeffrey A.

2012-01-01

Purpose: Studies have shown that women who engage in high levels of physical activity have higher rates of cancer screening, including Papanicalaou (Pap) tests. Because American Indian (AI) women are at high risk for cervical cancer morbidity and mortality, we examined Pap screening prevalence and assessed whether physical activity was associated…

A Complete Characterization of Potential Compensation Tests of Hicksian Welfare Measures

OpenAIRE

Donald Keenan; Arthur Snow

1999-01-01

In this paper, the authors present complete characterizations of the compensation tests for potential Pareto superiority proposed by Kaldor, Hicks, and Samuelson in terms of the aggregate Hicksian measures of income compensation, including compensating and equivalent variations. The key to obtaining these characterizations lies in recognizing that each potential compensation test entails a search over possible outcomes, rather than a comparison of only the new and original outcomes, as with s...

Physical examination tests for screening and diagnosis of cervicogenic headache: A systematic review.

Science.gov (United States)

Rubio-Ochoa, J; Benítez-Martínez, J; Lluch, E; Santacruz-Zaragozá, S; Gómez-Contreras, P; Cook, C E

2016-02-01

It has been suggested that differential diagnosis of headaches should consist of a robust subjective examination and a detailed physical examination of the cervical spine. Cervicogenic headache (CGH) is a form of headache that involves referred pain from the neck. To our knowledge, no studies have summarized the reliability and diagnostic accuracy of physical examination tests for CGH. The aim of this study was to summarize the reliability and diagnostic accuracy of physical examination tests used to diagnose CGH. A systematic review following PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analyses) guidelines was performed in four electronic databases (MEDLINE, Web of Science, Embase and Scopus). Full text reports concerning physical tests for the diagnosis of CGH which reported the clinometric properties for assessment of CGH, were included and screened for methodological quality. Quality Appraisal for Reliability Studies (QAREL) and Quality Assessment of Studies of Diagnostic Accuracy (QUADAS-2) scores were completed to assess article quality. Eight articles were retrieved for quality assessment and data extraction. Studies investigating diagnostic reliability of physical examination tests for CGH scored poorer on methodological quality (higher risk of bias) than those of diagnostic accuracy. There is sufficient evidence showing high levels of reliability and diagnostic accuracy of the selected physical examination tests for the diagnosis of CGH. The cervical flexion-rotation test (CFRT) exhibited both the highest reliability and the strongest diagnostic accuracy for the diagnosis of CGH. Copyright © 2015 Elsevier Ltd. All rights reserved.

Hydrologic test plans for large-scale, multiple-well tests in support of site characterization at Hanford, Washington

International Nuclear Information System (INIS)

Rogers, P.M.; Stone, R.; Lu, A.H.

1985-01-01

The Basalt Waste Isolation Project is preparing plans for tests and has begun work on some tests that will provide the data necessary for the hydrogeologic characterization of a site located on a United States government reservation at Hanford, Washington. This site is being considered for the Nation's first geologic repository of high level nuclear waste. Hydrogeologic characterization of this site requires several lines of investigation which include: surface-based small-scale tests, testing performed at depth from an exploratory shaft, geochemistry investigations, regional studies, and site-specific investigations using large-scale, multiple-well hydraulic tests. The large-scale multiple-well tests are planned for several locations in and around the site. These tests are being designed to provide estimates of hydraulic parameter values of the geologic media, chemical properties of the groundwater, and hydrogeologic boundary conditions at a scale appropriate for evaluating repository performance with respect to potential radionuclide transport

Characterization testing support requirements for the exploratory shaft facility at Yucca mountain

International Nuclear Information System (INIS)

Kalia, H.N.; Klkins, N.Z.

1990-01-01

The National waste Policy Act of 1982, as amended on December 22, 1987, requires that before proceeding to sink exploratory shafts at the Yucca Mountain site, the Secretary of the Department of Energy (DOE) shall submit to the Nuclear Regulatory Commission and to the Governor of Nevada or Legislature of the State of Nevada, for their review and comment, a general plane for the characterization activities to be conducted at the Yucca Mountain site. DOE submitted a Site Characterization Plan in December of 1988. This plan outlines activities to be undertaken by DOE to characterize the Yucca Mountain site as potentially the first national repository for the permanent isolation of high-level radioactive waste as well as the quality assurance (QA) program that will be applied on this project. The DOE plans to utilize an Exploratory Shaft Facility (ESF) to gain access to the underground environment and conduct characterization, construction, and mining-method evaluation and performance-related tests. This paper identifies the types of ESF tests to be performed, test requirements with respect to facility design, and the management of the testing program. An important ESF test program element is the design, installation, and management of an Integrated Data System (IDS), an automated system for collecting and recording test data for many of the tests. The rationale used in developing the facility and methodology used to develop testing and IDS requirements are also discussed in this paper

Physiological capacity and physical testing in male elite team handball

DEFF Research Database (Denmark)

Michalsik, Lars Bojsen; Madsen, K.; Aagaard, P.

2015-01-01

and by subsequent physical testing. RESULTS: Mean heart rate and relative workload during match-play (N.=41) were 163 ± 5 beats·min⁻¹ (group means±SD) and 70.9 ± 6.0% of VO(2-max), respectively. Relative workload was lower (P... and high demands on the anaerobic energy systems during certain periods of the match. Indications of temporary fatigue and a subsequent decline in performance were observed, since the relative workload decreased both in the first and in the second half of the match. Physiological profiles and physical test......AIM: The aim of the present study was to examine the physical demands placed on male elite team handball players in relation to playing position. METHODS: Male elite team handball field players were evaluated during match-play over a six season time span using physiological measurements...

Microbiology and atmospheric processes: biological, physical and chemical characterization of aerosol particles

Directory of Open Access Journals (Sweden)

D. G. Georgakopoulos

2009-04-01

Full Text Available The interest in bioaerosols has traditionally been linked to health hazards for humans, animals and plants. However, several components of bioaerosols exhibit physical properties of great significance for cloud processes, such as ice nucleation and cloud condensation. To gain a better understanding of their influence on climate, it is therefore important to determine the composition, concentration, seasonal fluctuation, regional diversity and evolution of bioaerosols. In this paper, we will review briefly the existing techniques for detection, quantification, physical and chemical analysis of biological particles, attempting to bridge physical, chemical and biological methods for analysis of biological particles and integrate them with aerosol sampling techniques. We will also explore some emerging spectroscopy techniques for bulk and single-particle analysis that have potential for in-situ physical and chemical analysis. Lastly, we will outline open questions and further desired capabilities (e.g., in-situ, sensitive, both broad and selective, on-line, time-resolved, rapid, versatile, cost-effective techniques required prior to comprehensive understanding of chemical and physical characterization of bioaerosols.

Radiological, physical, and chemical characterization of transuranic wastes stored at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Apel, M.L.; Becker, G.K.; Ragan, Z.K.; Frasure, J.; Raivo, B.D.; Gale, L.G.; Pace, D.P.

1994-03-01

This document provides radiological, physical and chemical characterization data for transuranic radioactive wastes and transuranic radioactive and hazardous (i.e., mixed) wastes stored at the Idaho National Engineering Laboratory and considered for treatment under the Private Sector Participation Initiative Program (PSPI). Waste characterization data are provided in the form of INEL Waste Profile Sheets. These documents provide, for each content code, information on waste identification, waste description, waste storage configuration, physical/chemical waste composition, radionuclide and associated alpha activity waste characterization data, and hazardous constituents present in the waste. Information is provided for 139 waste streams which represent an estimated total volume of 39,380 3 corresponding to a total mass of approximately 19,000,000 kg. In addition, considerable information concerning alpha, beta, gamma, and neutron source term data specific to Rocky Flats Plant generated waste forms stored at the INEL are provided to assist in facility design specification

Towards testing quantum physics in deep space

Science.gov (United States)

Kaltenbaek, Rainer

2016-07-01

MAQRO is a proposal for a medium-sized space mission to use the unique environment of deep space in combination with novel developments in space technology and quantum technology to test the foundations of physics. The goal is to perform matter-wave interferometry with dielectric particles of up to 10^{11} atomic mass units and testing for deviations from the predictions of quantum theory. Novel techniques from quantum optomechanics with optically trapped particles are to be used for preparing the test particles for these experiments. The core elements of the instrument are placed outside the spacecraft and insulated from the hot spacecraft via multiple thermal shields allowing to achieve cryogenic temperatures via passive cooling and ultra-high vacuum levels by venting to deep space. In combination with low force-noise microthrusters and inertial sensors, this allows realizing an environment well suited for long coherence times of macroscopic quantum superpositions and long integration times. Since the original proposal in 2010, significant progress has been made in terms of technology development and in refining the instrument design. Based on these new developments, we submitted/will submit updated versions of the MAQRO proposal in 2015 and 2016 in response to Cosmic-Vision calls of ESA for a medium-sized mission. A central goal has been to address and overcome potentially critical issues regarding the readiness of core technologies and to provide realistic concepts for further technology development. We present the progress on the road towards realizing this ground-breaking mission harnessing deep space in novel ways for testing the foundations of physics, a technology pathfinder for macroscopic quantum technology and quantum optomechanics in space.

Characterization of spent fuel approved testing material---ATM-105

Energy Technology Data Exchange (ETDEWEB)

Guenther, R.J.; Blahnik, D.E.; Campbell, T.K.; Jenquin, U.P.; Mendel, J.E.; Thomas, L.E.; Thornhill, C.K.

1991-12-01

The characterization data obtained to data are described for Approved Testing Material 105 (ATM-105), which is spent fuel from Bundles CZ346 and CZ348 of the Cooper Nuclear Power Plant, a boiling-water reactor. This report is one in a series being prepared by the Materials Characterization Center at Pacific Northwest Laboratory (PNL) on spent fuel ATMs. The ATMs are receiving extensive examinations to provide a source of well-characterized spent fuel for testing in the US Department of Energy Office of Civilian Radioactive Waste Management (OCRWM) Program. ATM-105 consists of 88 full-length irradiated fuel rods with rod-average burnups of about 2400 GJ/kgM (28 MWd/kgM) and expected fission gas release of about 1%. Characterization data include (1) descriptions of as-fabricated fuel design, irradiation history, and subsequent storage and handling; (2) isotopic gamma scans; (3) fission gas analyses; (4) ceramography of the fuel and metallography of the cladding; (5) special fuel studies involving analytical transmission electron microscopy (AEM); (6) calculated nuclide inventories and radioactivities in the fuel and cladding; and (7) radiochemical analyses of the fuel and cladding. Additional analyses of the fuel are being conducted and will be included in planned revisions of this report.

Characterization testing of a 40 ampere hour bipolar nickel-hydrogen battery

Science.gov (United States)

Brewer, Jeffrey C.; Manzo, Michelle A.; Gemeiner, Russel P.

1990-01-01

Extensive characterization testing has been done on a second 40-ampere hour (A h), 10-cell, bipolar nickel-hydrogen (Ni-H2) battery, to study the effects of operating parameters such as charge and discharge rates, temperature, and pressure on capacity, A h and watt hour (W h) efficiencies, and end-of-charge and midpoint discharge voltages. Testing to date has produced many interesting results, with the battery performing well throughout the test matrix except during the high-rate (5 C and 10 C) discharges, where poorer than expected results were observed. The exact cause of this poor performance is, as yet, unknown. Small scale 2 in. x 2 in. battery tests are to be used in studying this problem. Low earth orbit cycle life testing at a 40-percent depth of discharge and 10 C is scheduled to follow the characterization testing.

Reliability of six physical performance tests in older people with dementia

NARCIS (Netherlands)

Blankevoort, C.G.; Heuvelen, M.J.; Scherder, E.J.A.

2012-01-01

Background. Physical performance tests are important for assessing the effect of physical activity interventions in older people with dementia, but their psychometric properties have not been systematically established within this specific population. Objective. The purpose of this study was to

Reliability of Six Physical Performance Tests in Older People With Dementia

NARCIS (Netherlands)

Blankevoort, Christiaan G.; van Heuvelen, Marieke J. G.; Scherder, Erik J. A.

Background. Physical performance tests are important for assessing the effect of physical activity interventions in older people with dementia, but their psychometric properties have not been systematically established within this specific population. Objective. The purpose of this study was to

Value of physical tests in diagnosing cervical radiculopathy : a systematic review

NARCIS (Netherlands)

Thoomes, Erik J; van Geest, Sarita; van der Windt, Danielle A; Falla, Deborah; Verhagen, Arianne P; Koes, Bart W; Thoomes-de Graaf, Marloes; Kuijper, Barbara; Scholten-Peeters, Wendy Gm; Vleggeert-Lankamp, Carmen L

Background context In clinical practice, the diagnosis of cervical radiculopathy is based on information from the patient history, physical examination and diagnostic imaging. Various physical tests may be performed, but their diagnostic accuracy is unknown. Purpose To summarize and update the

Characterization of tissue-equivalent materials for use in construction of physical phantoms

International Nuclear Information System (INIS)

Souza, Edvan V. de; Oliveira, Alex C.H. de; Vieira, Jose W.; Lima, Fernando R.A.

2013-01-01

Phantoms are physical or computational models used to simulate the transport of ionizing radiation, their interactions with human body tissues and evaluate the deposition of energy. Depending on the application, you can build phantoms of various types and features. The physical phantoms are made of materials with behavior similar to human tissues exposed to ionizing radiation, the so-called tissue-equivalent materials. The characterization of various tissue-equivalent materials is important for the choice of materials to be used is appropriate, seeking a better cost-benefit ratio. The main objective of this work is to produce tables containing the main characteristics of tissue-equivalent materials. These tables were produced in Microsoft Office Excel. Among the main features of tissue-equivalent materials that were added to the tables, are density, chemical composition, physical state, chemical stability and solubility. The main importance of this work is to contribute to the construction of high-quality physical phantoms and avoid the waste of materials

High School Physical Education Teachers' Attitudes and Use of Fitness Tests

Science.gov (United States)

Mercier, Kevin; Phillips, Sharon; Silverman, Stephen

2016-01-01

Recommendations for using and implementing fitness tests have been extensively researched and teachers' attitudes toward fitness tests are beginning to be studied. Less understood is how high school teachers use fitness tests and the role their attitudes toward fitness tests affect students' attitudes toward physical activity. The purpose of this…

An empirical analysis of the physical aptitude exam as a predictor of performance on the Physical Readiness Test

OpenAIRE

Patrick, Robert W.

2000-01-01

The Physical Aptitude Exam, administered to candidates in the Naval Academy admissions process to measure physical aptitude, consists of pullups for men or the flexed arm hang for women, a 300-yard shuttle run, a standing longiump, and a kneeling basketball throw. The Physical Readiness Test, administered semi-annually to all naval personnel including midshipmen, consists of modified situps, pushups, and a 1.5-mile run. The purpose of this research is to determine if the Physical Aptitude Exa...

The characterization and testing of candidate immobilization forms for the disposal of plutonium

International Nuclear Information System (INIS)

Bakel, A. J.; Buck, E. C.; Chamberlain, D. B.; Ebbinghaus, B. B.; Fortner, J. A.; Marra, J. C.; Mcgrail, B. P.; Mertz, C. J.; Peeler, D. K.; Shaw, H. F.; Strachan, D. M.; Van Konynenburg, R. A.; Vienna, J. D.; Wolf, S. F.

1997-01-01

Candidate immobilization forms for the disposal of surplus weapons-useable are being tested and characterized. The goal of the testing program was to provide sufficient data that, by August 1997, an informed selection of a single immobilization form could be made so that the form development and production R and D could be more narrowly focused. Two forms have been under consideration for the past two years: glass and ceramic. In August, 1997, the Department of Energy (DOE) selected ceramic for plutonium disposition, halting further work on the glass material. In this paper, we will briefly describe these two waste forms, then describe our characterization techniques and testing methods. The analytical methods used to characterize altered and unaltered samples are the same. A full suite of microscopic techniques is used. Techniques used include optical, scanning electron, and transmission electron microscopies. For both candidate immobilization forms, the analyses are used to characterize the material for the presence of crystalline phases and amorphous material. Crystalline materials, either in the untested immobilization form or in the alteration products from testing, are characterized with respect to morphology, crystal structure, and composition. The goal of these analyses is to provide data on critical issues such as Pu and neutron absorber volubility in the immobilization form, thermal stability, potential separation of absorber and Pu, and the long-term behavior of the materials. Results from these analyses will be discussed in the presentation. Testing methods include MCC-1 tests, product consistency tests (methods A and B), unsaturated ''drip'' tests, vapor hydration tests, single-pass flow-through tests, and pressurized unsaturated flow tests. Both candidate immobilization forms have very low dissolution rates; examples of typical test results will be reported

Ancient mortars from Cape Verde: mineralogical and physical characterization

Science.gov (United States)

Rocha, Fernando; Costa, Cristiana; Velosa, Ana; Quintela, Ana; Terroso, Denise; Marques, Vera

2014-05-01

Times and locations of different building constructions means different knowledge, habits, different construction methods and materials. The study and safeguarding of the architectural heritage takes nowadays a progressive importance as a vehicle for transmission of cultures and history of nations. The coatings are of great importance in the durability of a building due to the protective role of the masonry. The compatibility between the materials with which they are executed (masonry, mortar and grout settlement) promotes the proper functioning of the wall and a consequent increase in durability. Therefore, it becomes important to study and characterize the mortar coating of buildings to know its characteristics and to use compatible materials in the rehabilitation and maintenance of buildings. This study aims to characterize the chemical, physical, mechanical and mineralogical mortar samples collected in buildings in three islands of Cape Verde, for the conservation, rehabilitation and preservation of them. The collected samples belong to buildings constructed in the end of XIX century and in the beginning of XX century. In order to characterize the mortar samples some tests was made, such as X-Ray Diffraction, X- Ray Fluorescence, acid attack and mechanical strength. The samples were divided into three groups depending on origin; so we have a first group collected on the island of Santiago, the second on the island of Saint Vincent and the third on the island of Santo Antao. The samples are all carbonated, but Santiago samples have a lower carbonates content. In terms of insoluble residue (from the acid attack) it was concluded that the samples have similar value ranging from 9 to 26%. The compressive strength of the mortars have a range between 1.36 and 4.55 MPa, which is related to the presence of more binder in samples with higher resistance. The chemical and mineralogical analyzes showed that these consist of lime mortars (binder), natural pozzolan and

Nanostructured tin oxide films: Physical synthesis, characterization, and gas sensing properties.

Science.gov (United States)

Ingole, S M; Navale, S T; Navale, Y H; Bandgar, D K; Stadler, F J; Mane, R S; Ramgir, N S; Gupta, S K; Aswal, D K; Patil, V B

2017-05-01

Nanostructured tin oxide (SnO 2 ) films are synthesized using physical method i.e. thermal evaporation and are further characterized with X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, transmission electron microscopy, and atomic force microscopy measurement techniques for confirming its structure and morphology. The chemiresistive properties of SnO 2 films are studied towards different oxidizing and reducing gases where these films have demonstrated considerable selectivity towards oxidizing nitrogen dioxide (NO 2 ) gas with a maximum response of 403% to 100ppm @200°C, and fast response and recovery times of 4s and 210s, respectively, than other test gases. In addition, SnO 2 films are enabling to detect as low as 1ppm NO 2 gas concentration @200°C with 23% response enhancement. Chemiresistive performances of SnO 2 films are carried out in the range of 1-100ppm and reported. Finally, plausible adsorption and desorption reaction mechanism of NO 2 gas molecules with SnO 2 film surface has been thoroughly discussed by means of an impedance spectroscopy analysis. Copyright © 2017 Elsevier Inc. All rights reserved.

Differences in gender performance on competitive physics selection tests

Directory of Open Access Journals (Sweden)

Kate Wilson

2016-08-01

Full Text Available [This paper is part of the Focused Collection on Gender in Physics.] We have investigated gender differences in performance over the past eight years on the Australian Science Olympiad Exam (ASOE for physics, which is taken by nearly 1000 high school students each year. The ASOE, run by Australian Science Innovations (ASI, is the initial stage of the process of selection of teams to represent Australia at the Asian and International Physics Olympiads. Students taking the exam are generally in their penultimate year of school and selected by teachers as being high performing in physics. Together with the overall differences in facility, we have investigated how the content and presentation of multiple-choice questions (MCQs affects the particular answers selected by male and female students. Differences in the patterns of responses by male and female students indicate that males and females might be modeling situations in different ways. Some strong patterns were found in the gender gaps when the questions were categorized in five broad dimensions: content, process required, difficulty, presentation, and context. Almost all questions saw male students performing better, although gender differences were relatively small for questions with a more abstract context. Male students performed significantly better on most questions with a concrete context, although notable exceptions were found, including two such questions where female students performed better. Other categories that showed consistently large gaps favoring male students include questions with projectile motion and other two-dimensional motion or forces content, and processes involving interpreting diagrams. Our results have important implications, suggesting that we should be able to reduce the gender gaps in performance on MCQ tests by changing the way information is presented and setting questions in contexts that are less likely to favor males over females. This is important as MCQ

Characterization methods for ultrasonic test systems

International Nuclear Information System (INIS)

Busse, L.J.; Becker, F.L.; Bowey, R.E.; Doctor, S.R.; Gribble, R.P.; Posakony, G.J.

1982-07-01

Methods for the characterization of ultrasonic transducers (search units) and instruments are presented. The instrument system is considered as three separate components consisting of a transducer, a receiver-display, and a pulser. The operation of each component is assessed independently. The methods presented were chosen because they provide the greatest amount of information about component operation and were not chosen based upon such conditions as cost, ease of operation, field implementation, etc. The results of evaluating a number of commercially available ultrasonic test instruments are presented

Feasibility and Reliability of Physical Fitness Tests in Older Adults with Intellectual Disability: A Pilot Study

Science.gov (United States)

Hilgenkamp, Thessa I. M.; van Wijck, Ruud; Evenhuis, Heleen M.

2012-01-01

Background: Physical fitness is relevant for wellbeing and health, but knowledge on the feasibility and reliability of instruments to measure physical fitness for older adults with intellectual disability is lacking. Methods: Feasibility and test-retest reliability of a physical fitness test battery (Box and Block Test, Response Time Test, walking…

Exploration of task performance tests in a physics laboratory

Science.gov (United States)

Liu, Dan; El Turkey, Houssein

2017-11-01

In this article, we investigate the implementation of task performance tests in an undergraduate physics laboratory. Two performance tests were carried out over two semesters using the task of building a DC circuit. The first implementation in Spring 2014 had certain concerns such as the privacy of students’ testing and their ‘trial and error’ attempts. These concerns were addressed in Fall 2015 through implementing a second performance test. The second implementation was administered differently but the content of the two tests was the same. We discuss the validity of both implementations and present the correlation (or lack of) between the time that students needed to complete the tests and their grades from a paper-based laboratory assessment method.

Relationship of physical examination test of shoulder instability to arthroscopic findings in dogs.

Science.gov (United States)

Devitt, Chad M; Neely, Marlon R; Vanvechten, Brian J

2007-10-01

To determine the diagnostic validity of commonly used physical examination maneuvers for shoulder instability. Retrospective study. Dogs (n=24) referred for shoulder arthroscopy. Results of physical maneuvers and arthroscopic findings were recorded and sensitivity, specificity, positive likelihood ratios (LR+), and negative likelihood ratios (LR-) were calculated for each of 4 physical examination test findings for arthroscopic changes in the medial, lateral, cranial, or caudal compartments of the shoulder joint viewed in dorsal recumbency by lateral and craniomedial portals. Distribution of compartment changes was: medial (17 dogs), caudal (15), cranial (12), and lateral (5). The biceps test had a moderate effect (LR+=9) on post-test probability of cranial compartment changes and a small effect on post-test probability of lateral and caudal compartment changes (LR+=3 and 2.4, respectively). Hyperabduction had a minimal effect and mediolateral instability test had a small effect (LR+=1.64 and 2.68, respectively) on post-test probability of medial compartment changes. Craniocaudal instability test had little to no effect on post-test probability of changes in any compartment. Physical examination tests evaluated were limited in their ability to predict the type of arthroscopic pathology in this study population. Clinicians should understand that a diagnostic test performs inconsistently based on prevalence of a condition in a given patient population. The use of likelihood ratios can assist clinicians in determining the probability of intraarticular changes from a group with a differing prevalence than the patient population presented.

Project Physics Tests 3, The Triumph of Mechanics.

Science.gov (United States)

Harvard Univ., Cambridge, MA. Harvard Project Physics.

Test items relating to Project Physics Unit 3 are presented in this booklet. Included are 70 multiple-choice and 20 problem-and-essay questions. Concepts of mechanics are examined on energy, momentum, kinetic theory of gases, pulse analyses, "heat death," water waves, power, conservation laws, normal distribution, thermodynamic laws, and…

Validity of the German Version of the Continuous-Scale Physical Functional Performance 10 Test

Directory of Open Access Journals (Sweden)

Irene Härdi

2017-01-01

Full Text Available Background. The Continuous-Scale Physical Functional Performance 10 Test (CS-PFP 10 quantitatively assesses physical functional performance in older adults who have a broad range of physical functional ability. This study assessed the validity and reliability of the CS-PFP 10 German version. Methods. Forward-translations and backtranslations as well as cultural adaptions of the test were conducted. Participants were German-speaking Swiss community-dwelling adults aged 64 and older. Concurrent validity was assessed using Pearson correlation coefficients between CS-PFP 10 and gait velocity, Timed Up and Go Test, hand grip strength, SF-36 physical function domain, and Freiburger Physical Activity Questionnaire. Internal consistency was calculated by Cronbach’s alpha. Results. Backtranslation and cultural adaptions were accepted by the CS-PFP 10 developer. CS-PFP 10 total score and subscores (upper body strength, upper body flexibility, lower body strength, balance and coordination, and endurance correlated significantly with all measures of physical function tested. Internal consistency was high (Cronbach’s alpha 0.95–0.98. Conclusion. The CS-PFP 10 German version is valid and reliable for measuring physical functional performance in German-speaking Swiss community-dwelling older adults. Quantifying physical function is essential for clinical practice and research and provides meaningful insight into physical functional performance of older adults. This trial is registered with ClinicalTrials.gov NCT01539200.

Characterization and vitrification of Hanford radioactive high level wastes

International Nuclear Information System (INIS)

Tingey, J.M.; Elliott, M.L.; Larson, D.E.; Morrey, E.V.

1991-01-01

Radioactive Neutralized Current Acid Waste (NCAW) samples from the Hanford waste tanks have been chemically, radiochemically and physically characterized. The wastes were processed according to the Hanford Waste vitrification Plant (HWVP) flowsheet, and characterized after each process step. The waste glasses were sectioned and leach tested. Chemical, radiochemical and physical properties of the waste will be presented and compared to nonradioactive simulant data and the HWVP reference composition and properties

Standard practice for analysis and interpretation of physics dosimetry results for test reactors

International Nuclear Information System (INIS)

Anon.

1984-01-01

This practice describes the methodology summarized in Annex Al to be used in the analysis and interpretation of physics-dosimetry results from test reactors. This practice relies on, and ties together, the application of several supporting ASTM standard practices, guides, and methods that are in various stages of completion (see Fig. 1). Support subject areas that are discussed include reactor physics calculations, dosimeter selection and analysis, exposure units, and neutron spectrum adjustment methods. This practice is directed towards the development and application of physics-dosimetrymetallurgical data obtained from test reactor irradiation experiments that are performed in support of the operation, licensing, and regulation of LWR nuclear power plants. It specifically addresses the physics-dosimetry aspects of the problem. Procedures related to the analysis, interpretation, and application of both test and power reactor physics-dosimetry-metallurgy results are addressed in Practice E 853, Practice E 560, Matrix E 706(IE), Practice E 185, Matrix E 706(IG), Guide E 900, and Method E 646

Quantitative investigation of ligament strains during physical tests for sacroiliac joint pain using finite element analysis.

Science.gov (United States)

Kim, Yoon Hyuk; Yao, Zhidong; Kim, Kyungsoo; Park, Won Man

2014-06-01

It may be assumed that the stability is affected when some ligaments are injured or loosened, and this joint instability causes sacroiliac joint pain. Several physical examinations have been used to diagnose sacroiliac pain and to isolate the source of the pain. However, more quantitative and objective information may be necessary to identify unstable or injured ligaments during these tests due to the lack of understanding of the quantitative relationship between the physical tests and the biomechanical parameters that may be related to pains in the sacroiliac joint and the surrounding ligaments. In this study, a three-dimensional finite element model of the sacroiliac joint was developed and the biomechanical conditions for six typical physical tests such as the compression test, distraction test, sacral apex pressure test, thigh thrust test, Patrick's test, and Gaenslen's test were modelled. The sacroiliac joint contact pressure and ligament strain were investigated for each test. The values of contact pressure and the combination of most highly strained ligaments differed markedly among the tests. Therefore, these findings in combination with the physical tests would be helpful to identify the pain source and to understand the pain mechanism. Moreover, the technology provided in this study might be a useful tool to evaluate the physical tests, to improve the present test protocols, or to develop a new physical test protocol. Copyright © 2013 Elsevier Ltd. All rights reserved.

Test-retest reliability of Eurofit Physical Fitness items for children with visual impairments

NARCIS (Netherlands)

Houwen, Suzanne; Visscher, Chris; Hartman, Esther; Lemmink, Koen A. P. M.

The purpose of this study was to examine the test-retest reliability of physical fitness items from the European Test of Physical Fitness (Eurofit) for children with visual impairments. A sample of 21 children, ages 6-12 years, that were recruited from a special school for children with visual

Tests and standards for express-control of physical fitness and health of middle school age pupils

Directory of Open Access Journals (Sweden)

I.R. Bodnar

2016-08-01

Full Text Available Introduction: to day, physical fitness testing often causes negative emotions in pupils. It results in sharp loss of pupils’ wish to fulfill physical exercises in free time and worsens their health. Possibility to assess health level is an important motivation factor for pupils’ passing physical tests. Objective testing system will form positive motivation for physical exercises’ practicing and will facilitate increase of pupils’ motor functioning. It will also facilitate optimization of their physical condition, improvement of physical fitness and strengthening of health. Material: we tested physical fitness level and made diagnosis of pupils’ functional state (10-15 years’ age; n=85 with the help of tool methodic. We also used regressive analysis. Results: the system of tests and standards for express-control over physical fitness and health of middle school age pupils has been worked out and substantiated. The system of tests envisages fulfillment of 4 exercises: back pressing ups on bench during 20 seconds; throwing and catching of ball with two hands from wall during 30 seconds; side bending; torso rising from lying position into sitting during 30 seconds. Integral indicator of pupils’ physical fitness and health correlates with functional state of organism’s leading systems. We worked out 5 levels’ scale for express-control over physical fitness and health of middle school age pupils. The system stipulates calculation of integrative indicator with the help of regression equation by results of 4 test exercises and calculation of one index. Conclusions: The system of tests and standards permits the following: to divide pupils into relatively uniform groups even at the beginning of academic year for successful reasonable physical load. The system also permits to determine standard and find what shall be strived for by a pupil in order to achieve optimal physical fitness and somatic state; to motivate relatively weakly

Physical and morphometric characterization of indigenous cattle of Assam

Directory of Open Access Journals (Sweden)

A. Haque

2011-01-01

Full Text Available The present investigation was undertaken to study the physical and morphometric characteristics in indigenous cattle of Assam. The data pertain to 339 indigenous cattle of different categories. The physical characteristics included colour pattern of body coat, muzzle, tail switch, hoof and horn. Body length, height at wither, heart girth, pouch girth, length of tail, switch, neck, ear and head were taken up for morphometric characterization. The main body coat colour of indigenous cattle was brown (31.18% followed by white (28.53%, fawn (15.29%, grey (13.53%, black (4.41% and mixed (7.06%. The prominent colour of tail switch was black (74.53%. Most of animals had black muzzle (86.47%, black hooves (84.71% and black horn (100%. Morphometric characteristics data obtained were classified according to location, age group and sex of the animal. The means for body length, height at wither, heart girth, pouch girth, length of tail, switch, neck, ear and head were 83.668±0.590, 91.942±0.55, 113.146±0.738, 121.181±0.761, 54.196±0.527, 26.098±0.186, 32.705±0.166, 18.131±0.111 and 35.035±0.195 cm respectively. Age and sex had significant effect on all the morphometric characters however, location effect was non significant. The indigenous cattle of Assam are comparatively smaller in size than most of the recognized breeds of cattle however coat colour showed sizeable variation. The data generated for indigenous cattle of Assam would be useful to characterize them.

Project Physics Tests 2, Motion in the Heavens.

Science.gov (United States)

Harvard Univ., Cambridge, MA. Harvard Project Physics.

Test items relating to Project Physics Unit 2 are presented in this booklet. Included are 70 multiple-choice and 22 problem-and-essay questions. Concepts of motion in the heavens are examined for planetary motions, heliocentric theory, forces exerted on the planets, Kepler's laws, gravitational force, Galileo's work, satellite orbits, Jupiter's…

Physical Characterization of Solid-Liquid Slurries at High Weight Fractions Using Optical and Ultrasonic Methods. Final Report

International Nuclear Information System (INIS)

Burgess, Lloyd W.

2009-01-01

Remediation of highly radioactive waste is a major technical and programmatic challenge for the DOE. Rapid, on-line physical characterization of highly concentrated slurries is required for the safe and efficient remediation of 90 million gallons of high level radioactive waste (HLW), sodium bearing waste, and mixed waste. The research presented here, describes a collaborative effort between Pacific Northwest National Laboratory (PNNL) and the University of Washington to directly address the need for rapid on-line characterization of the physical properties of HLW slurries during all phases of the remediation process, from in-tank characterization of sediments to monitoring of the concentration, particle size, and degree of agglomeration and gelation of slurries during transport. Near-surface characterization of the slurry flow in the particle size range from nanometer to micrometer is examined using optical low coherence reflectometry. Volumetric characterization at depths in the slurry flow, up to several centimeters in the particle size range from the micrometer to millimeter, is realized by utilizing ultrasonic backscatter and diffuses fields. One of the strengths, the teaming up of significant talents in both experimental and theoretical optics (University of Washington) and in ultrasonics (Pacific Northwest National Laboratory (PNNL)) provides a synergistic approach to integrate these complimentary techniques. One of the benefits of this combined approach is the physical characterization of HLW over a concentration and particle size range that is broader than can be achieved with today's technology. This will avoid a costly increase in waste stream volume due to excess dilution, and will lessen chance of plugging pipes that could shut down expensive processing lines.

A test to evaluate the physical impact on technical performance in soccer

DEFF Research Database (Denmark)

Rostgaard, Thomas; Iaia, F. Marcello; Simonsen, Dennis S.

2008-01-01

The aim of the study was to develop and examine a test for evaluation of the physical and technical capacity of soccer players. Fourteen youth elite (YE) and seven sub-elite (SE) players performed a physical and technical test (PT-test) consisting of 10 long kicks interspersed with intense......(-1), and 76 +/- 11 umol L(-1) at the end of the test, respectively. After the test muscle CP, glycogen and lactate was 52.9 +/- 6.6, 354 +/- 39, and 25.3 +/- 5.9 mmol kg(-1) d.w., respectively. In summary, the PT-test can be used to evaluate a soccer player's technical skills under conditions similar...... intermittent exercise. In addition, a control test (CON-test) without intense exercise was performed. In both cases, the test result was evaluated by the precision of the 10 kicks. The players also performed the Yo-Yo intermittent recovery test level 2 (Yo-Yo IR2). For the SE-players, blood samples were...

Nuclear physics at PEP: First test and future plans

International Nuclear Information System (INIS)

Van Bibber, K.; Dietrich, F.S.; Melnikoff, S.O.

1986-09-01

A test run of internal target nuclear physics at the PEP storage ring is described. The Time Projection Chamber (TPC-2γ detector) was used to detect the inelastically scattered electron and complete hadronic final state in the interaction of 14.5 GeV electrons with D 2 , Ar and Xe gas targets. The data comprise mostly low-x low-Q 2 events, but some deep inelastic scattering as well. The future possibilities of a dedicated nuclear physics program at PEP are outlined. 15 refs., 25 figs

Asphalt mix characterization using dynamic modulus and APA testing.

Science.gov (United States)

2005-11-01

final report summarizes two research efforts related to asphalt mix characterization: dynamic modulus and Asphalt Pavement Analyzer testing. One phase of the research consisted of a laboratory-based evaluation of dynamic modulus of Oregon dense-grade...

Is the Physical Being Taken out of Physical Education? On the Possible Effects of High-Stakes Testing on an Embattled Profession's Curriculum Goals

Science.gov (United States)

Seymour, Clancy; Garrison, Mark

2015-01-01

Building on recent discussions regarding how current national standards for physical education promote cognitive outcomes over physical outcomes, the authors explore how a new era in high-stakes testing is also contributing to an emphasis on the cognitive, over the physical. While high-stakes testing has been linked to reducing the amount of…

Procedures and reasoning for skill proficiency testing in physical education teacher education programs

Directory of Open Access Journals (Sweden)

Timothy Baghurst

2015-12-01

Full Text Available This study sought to determine how the testing of skill proficiency is being conducted in physical education teacher education (PETE programs in the USA and how fitness or skill proficiencies, as attributes of a physical educator, are perceived. Participants were 312 college PETE program coordinators who completed an online survey about skill testing in their program. The eligible respondents yielded a 52.7% total response rate. Most participants believed that skill proficiency for PETE students was important, but only 46% of programs reported testing within their program. Many participants stated it was possible for their students to graduate without demonstrating proficiency in skill technique, yet were confident their students would pass an independent skill test. Only 46.2% of respondents indicated their students needed to demonstrate proper skill technique in order to graduate, and there was no consistent method of assessment. Responses were evenly split regarding the importance of a physical educator being able to demonstrate proper skill technique or be physically fit. The lack of skill testing in programs, combined with the variation in assessment, is concerning, and the development of a standardized skill-based test may provide more rigor to this important area of teacher credibility and effectiveness.

Materials Characterization Center meeting on impact testing of waste forms. Summary report

International Nuclear Information System (INIS)

Merz, M.D.; Atteridge, D.; Dudder, G.

1981-10-01

A meeting was held on March 25-26, 1981 to discuss impact test methods for waste form materials to be used in nuclear waste repositories. The purpose of the meeting was to obtain guidance for the Materials Characterization Center (MCC) in preparing the MCC-10 Impact Test Method to be approved by the Materials Review Board. The meeting focused on two essential aspects of the test method, namely the mechanical process, or impact, used to effect rapid fracture of a waste form and the analysis technique(s) used to characterize particulates generated by the impact

Validity of Combining History Elements and Physical Examination Tests to Diagnose Patellofemoral Pain.

Science.gov (United States)

Décary, Simon; Frémont, Pierre; Pelletier, Bruno; Fallaha, Michel; Belzile, Sylvain; Martel-Pelletier, Johanne; Pelletier, Jean-Pierre; Feldman, Debbie; Sylvestre, Marie-Pierre; Vendittoli, Pascal-André; Desmeules, François

2018-04-01

To assess the validity of diagnostic clusters combining history elements and physical examination tests to diagnose or exclude patellofemoral pain (PFP). Prospective diagnostic study. Orthopedic outpatient clinics, family medicine clinics, and community-dwelling. Consecutive patients (N=279) consulting one of the participating orthopedic surgeons (n=3) or sport medicine physicians (n=2) for any knee complaint. Not applicable. History elements and physical examination tests were obtained by a trained physiotherapist blinded to the reference standard: a composite diagnosis including both physical examination tests and imaging results interpretation performed by an expert physician. Penalized logistic regression (least absolute shrinkage and selection operator) was used to identify history elements and physical examination tests associated with the diagnosis of PFP, and recursive partitioning was used to develop diagnostic clusters. Diagnostic accuracy measures including sensitivity, specificity, positive and negative predictive values, and positive and negative likelihood ratios with associated 95% confidence intervals (CIs) were calculated. Two hundred seventy-nine participants were evaluated, and 75 had a diagnosis of PFP (26.9%). Different combinations of history elements and physical examination tests including the age of participants, knee pain location, difficulty descending stairs, patellar facet palpation, and passive knee extension range of motion were associated with a diagnosis of PFP and used in clusters to accurately discriminate between individuals with PFP and individuals without PFP. Two diagnostic clusters developed to confirm the presence of PFP yielded a positive likelihood ratio of 8.7 (95% CI, 5.2-14.6) and 3 clusters to exclude PFP yielded a negative likelihood ratio of .12 (95% CI, .06-.27). Diagnostic clusters combining common history elements and physical examination tests that can accurately diagnose or exclude PFP compared to various knee

Characterization of Physic nut (Jatropha curcas L.) shells

International Nuclear Information System (INIS)

Wever, Diego-Armando Z.; Heeres, H.J.; Broekhuis, Antonius A.

2012-01-01

The characterization of Physic nut shells was done using the wet chemical analysis of wood components. The obtained fractions were analyzed using IR, NMR, GPC, ICP and MALDI-TOF mass spectroscopy. TGA was used to determine the fixed carbon (+ash) and water content of the shells. The results of wet chemical analysis of wood components offered a clear procedure to isolate the main components in Physic nut shells (a). The fractions obtained were: polar extract (b), non-polar extract (c), Acid Insoluble Lignin (d), Holocellulose (e), α-Cellulose (f). The total Lignin content present in the shells equaled 48.84%. IR and NMR spectroscopy demonstrated that the non-polar extract is Lignin, which corresponds to the extractable Lignin (1.24%) in the Physic nut shells and the Acid Insoluble Lignin was 47.60%. Elemental analysis showed no Sulfur present in the investigated materials. Furthermore both 1 H and 13 C NMR of the non-polar extract showed the presence of aliphatic hydrocarbon chains. The α-Cellulose content (22.29%) and the Hemicelluloses content (23.84%) were in line with that of agricultural residues. The water content and the fixed carbon content (+ash [2.8%]) equal 5–6% and 35.6%, respectively. GPC showed that the polydispersity of the non-polar extract (3.6) lies between Alcell Lignin and Kraft Lignin. The polar extract contains a variety of metals, with especially a high amount of the alkali metals K and Na. The extraction with water is proposed to generate a fertilizer fraction and may be applied to reduce potential sintering issues during eventual combustion or gasification of the shells. -- Highlights: ► Physic nut shell is a potential source of value added chemicals due to its high lignin content (48.8 wt%). ► Lignin extracted from Jatropha curcas L. shells is rich in aliphatic linkages. ► Water extraction of the shells yields a potential fertilizer fraction rich in alkali metals and phosphorous. ► Pre-extraction is recommended to eliminate

Characterization of cracking in Strain-Hardening Cementitious Composites using the compact tension test

DEFF Research Database (Denmark)

Pereira, Eduardo B.; Fischer, Gregor; Barros, Joaquim A. O.

The characterization of the tensile behavior of strain hardening cementitious composites (SHCC) is of significant importance to the material design. In a previous work the tensile stress-crack opening response of different types of SHCC was characterized using notched specimens tested in direct...... tension, where a single crack was obtained and mechanically characterized by performing Single Crack Tension Test (SCTT). In this study the tensile behavior of SHCC materials is characterized under eccentric tensile load using the Compact Tension Test (CTT). The long edge notch placed in the rectangular...... plate specimens and the eccentrically applied tensile load create the local conditions necessary to the initiation of a single crack at the tip of the notch. Further propagation and opening of the crack in Mode I allow the assessment of the tensile load-displacement relationship. The experimental...

Improvement of defect characterization in ultrasonic testing by adaptative learning network

International Nuclear Information System (INIS)

Bieth, M.; Adamonis, D.C.; Jusino, A.

1982-01-01

Numerous methods exist now for signal analysis in ultrasonic testing. These methods give more or less accurate information for defects characterization. In this paper is presented the development of a particular system based on a computer Signal processing: the Adaptative Learning Network (ALN) allowing the discrimination of defects in function of their nature. The ultrasonic signal is sampled and characterized by parameters amplitude-time and amplitude-frequency. The method was tested on stainless steel tubes welds showing fatigue cracks. The ALN model developed allows, under certain conditions, the discrimination of cracks from other defects [fr

Methods for the physical characterization and quantification of extracellular vesicles in biological samples.

Science.gov (United States)

Rupert, Déborah L M; Claudio, Virginia; Lässer, Cecilia; Bally, Marta

2017-01-01

Our body fluids contain a multitude of cell-derived vesicles, secreted by most cell types, commonly referred to as extracellular vesicles. They have attracted considerable attention for their function as intercellular communication vehicles in a broad range of physiological processes and pathological conditions. Extracellular vesicles and especially the smallest type, exosomes, have also generated a lot of excitement in view of their potential as disease biomarkers or as carriers for drug delivery. In this context, state-of-the-art techniques capable of comprehensively characterizing vesicles in biological fluids are urgently needed. This review presents the arsenal of techniques available for quantification and characterization of physical properties of extracellular vesicles, summarizes their working principles, discusses their advantages and limitations and further illustrates their implementation in extracellular vesicle research. The small size and physicochemical heterogeneity of extracellular vesicles make their physical characterization and quantification an extremely challenging task. Currently, structure, size, buoyant density, optical properties and zeta potential have most commonly been studied. The concentration of vesicles in suspension can be expressed in terms of biomolecular or particle content depending on the method at hand. In addition, common quantification methods may either provide a direct quantitative measurement of vesicle concentration or solely allow for relative comparison between samples. The combination of complementary methods capable of detecting, characterizing and quantifying extracellular vesicles at a single particle level promises to provide new exciting insights into their modes of action and to reveal the existence of vesicle subpopulations fulfilling key biological tasks. Copyright © 2016 Elsevier B.V. All rights reserved.

Site Characterization of the Source Physics Experiment Phase II Location Using Seismic Reflection Data

Science.gov (United States)

Sexton, E. A.; Snelson, C. M.; Chipman, V.; Emer, D. F.; White, R. L.; Emmitt, R.; Wright, A. A.; Drellack, S.; Huckins-Gang, H.; Mercadante, J.; Floyd, M.; McGowin, C.; Cothrun, C.; Bonal, N.

2013-12-01

An objective of the Source Physics Experiment (SPE) is to identify low-yield nuclear explosions from a regional distance. Low-yield nuclear explosions can often be difficult to discriminate among the clutter of natural and man-made explosive events (e.g., earthquakes and mine blasts). The SPE is broken into three phases. Phase I has provided the first of the physics-based data to test the empirical models that have been used to discriminate nuclear events. The Phase I series of tests were placed within a highly fractured granite body. The evolution of the project has led to development of Phase II, to be placed within the opposite end member of geology, an alluvium environment, thereby increasing the database of waveforms to build upon in the discrimination models. Both the granite and alluvium sites have hosted nearby nuclear tests, which provide comparisons for the chemical test data. Phase III of the SPE is yet to be determined. For Phase II of the experiment, characterization of the location is required to develop the geologic/geophysical models for the execution of the experiment. Criteria for the location are alluvium thickness of approximately 170 m and a water table below 170 m; minimal fracturing would be ideal. A P-wave mini-vibroseis survey was conducted at a potential site in alluvium to map out the subsurface geology. The seismic reflection profile consisted of 168 geophone stations, spaced 5 m apart. The mini-vibe was a 7,000-lb peak-force source, starting 57.5 m off the north end of the profile and ending 57.5 m past the southern-most geophone. The length of the profile was 835 m. The source points were placed every 5 m, equally spaced between geophones to reduce clipping. The vibroseis sweep was from 20 Hz down to 180 Hz over 8 seconds, and four sweeps were stacked at each shot location. The shot gathers show high signal-to-noise ratios with clear first arrivals across the entire spread and the suggestion of some shallow reflectors. The data were

Destructive physical analysis of hollow cathodes from the Deep Space 1 Flight spare ion engine 30,000 hr life test

Science.gov (United States)

Sengupta, Anita

2005-01-01

Destructive physical analysis of the discharge and neutralizer hollow cathode assemblies from the Deep Space 1 Flight Spare 30,000 Hr life test was performed to characterize physical and chemical evidence of operationally induced effects after 30,372 hours of operation with beam extraction. Post-test inspection of the discharge-cathode assembly was subdivided into detailed analyses at the subcomponent level. Detailed materials analysis and optical inspection of the insert, orifice plate, cathode tube, heater, keeper assembly, insulator, and low-voltage propellant isolator were performed. Energy dispersive X-ray (EDX) and scanning electron microscopy (SEW analyses were used to determine the extent and composition of regions of net deposition and erosion of both the discharge and neutralizer inserts. A comparative approach with an un-operated 4:1:1 insert was used to determine the extent of impregnate material depletion as a function of depth from the ID surface and axial position from the orifice plate. Analysis results are compared and contrasted with those obtained from similar analyses on components from shorter term tests, and provide insight regarding the prospect for successful longer-term operation consistent with SOA ion engine program life objectives at NASA.

Characterization of Physical and Thermal Properties of Biofield Treated Neopentyl Glycol

OpenAIRE

Trivedi, Dahryn; Trivedi, Mahendra Kumar; Branton, Alice; Nayak, Gopal

2015-01-01

Neopentyl glycol (NPG) has been extensively used as solid-solid phase change materials (PCMs) for thermal energy storage applications. The objective of the present study was to evaluate the impact of biofield treatment on physical, spectral and thermal properties of NPG. The study was performed in two groups (control and treated). The control group remained as untreated, and treatment group was subjected to Mr. Trivedi’s biofield treatment. The control and treated NPG were characterized by X-...

Final Physics Report for the Engineering Test Reactor

International Nuclear Information System (INIS)

Wolfe, I. B.

1956-01-01

This report is a summary of the physics design work performed on the Engineering Test Reactor. The ETR presents computational difficulties not found in other reactors because of the large number of experimental holes in the core. The physics of the ETR depends strongly upon the contents of the in-core experimental facilities. In order to properly evaluate the reactor' taking into account the experiments in the core, multi-region, two-dimensional calculations are required. These calculations require the use of a large computer such as the Remington Rand Univac and are complex and expensive enough to warrant a five-stage program: 1. In the early stages of design, only preliminary two-dimensional calculations were performed .in order to obtain a rough idea of the general behavior of the reactor and its critical mass with tentative experiments in place. 2. A large amount of work was carried out in which the reactor was approximated as one with a uniform homogeneous core. With this model, detailed studies were carried out to investigate the feasibility and to obtain general design data on such points as the design and properties of the gray and black control rods, the design of the beryllium reflector, gamma and neutron heating, the use of burnable poisons, etc. In performing these calculations, use was made of the IBM 650 PROD code obtained from KAPL. 3. With stages 1 and 2 carried out, two-dimensional calculations of the core at start-up conditions were performed on the Univac computer. 4. Detailed two-dimensional calculations of the properties of the ETR with a proposed first set of experiments in place were carried out. 5. A series of nuclear tests were performed at the reactivity measurements facility at the MTR site in order to confirm the validity of the analytical techniques in physics analysis. In performing the two-dimensional Univac calculations, the MUG code developed by KAPL and the Cuthill code developed at the David Taylor Model Basin were utilized. In

VISCOSE BASED MAGNETIC YARNS – PHYSICAL AND MECHANICAL CHARACTERIZATION

Directory of Open Access Journals (Sweden)

GROSU Marian-Cătălin

2017-05-01

Full Text Available In the context of the rapid growth in the number of electrical and electronic devices and accessories that emit electromagnetic energy in different frequency bands we present and characterize here several magnetic functionalized viscose twisted yarns. A 100% viscose twisted staple yarn was covered through an in-house developed process with a polymeric solution containing micrometric sized barium hexaferrite magnetic powder. The in-house developed process allows deposition of micrometric thickness polymeric paste layer on the yarn surface. Barium hexaferrite is a hard magnetic material exhibiting high chemical stability and corrosion resistivity, relatively large saturation and residual magnetization and microwave absorbing properties. Five different percentages of the magnetic powder in the polymer solution were used, i.e. ranging from 15 wt% to 45 wt%. Physical characterization shows a very good adherence between the highly hygroscopic viscose staple fibers and the polymeric solution that contains polyvinyl acetate and polyurethane as binders. SEM images evidenced the fact that the polymeric solution penetrated more than 1/3 of the yarn diameter. The concentration of magnetic powder in the polymeric solution has a direct influence on the coating amount, diameter and density. The mechanical characterization of the coated yarns revealed that the breaking force is increasing with increasing magnetic powder content up to o certain value and then decreased because the magnetic layer became stiffer. At the same time, the elongation at brake is decreasing.

The development of spatial orientation and laterality in physical education classes from the countryside - pilot test

Directory of Open Access Journals (Sweden)

Teodora-Mihaela Iconomescu

2017-01-01

Full Text Available The article aims to present a pilot test on the development of space orientation and laterality in pupils in primary education in the physical education lesson. Testing of psychomotricity components was performed by the Piaget Head and Harris test. The differences between the two initial and final tests have shown that through the physical movement of the physical education we have improved the two components of psychomotricity.

Physical examination tests for the diagnosis of posterior cruciate ligament rupture: a systematic review.

Science.gov (United States)

Kopkow, Christian; Freiberg, Alice; Kirschner, Stephan; Seidler, Andreas; Schmitt, Jochen

2013-11-01

Systematic literature review. To summarize and evaluate research on the accuracy of physical examination tests for diagnosis of posterior cruciate ligament (PCL) tear. Rupture of the PCL is a severe knee injury that can lead to delayed rehabilitation, instability, or chronic knee pathologies. To our knowledge, there is currently no systematic review of studies on the diagnostic accuracy of clinical examination tests to evaluate the integrity of the PCL. A comprehensive systematic literature search was conducted in MEDLINE from 1946, Embase from 1974, and the Allied and Complementary Medicine Database from 1985 until April 30, 2012. Studies were considered eligible if they compared the results of physical examination tests performed in the context of a PCL physical examination to those of a reference standard (arthroscopy, arthrotomy, magnetic resonance imaging). Methodological quality assessment was performed by 2 independent reviewers using the revised version of the Quality Assessment of Diagnostic Accuracy Studies (QUADAS-2) tool. The search strategy revealed 1307 articles, of which 11 met the inclusion criteria for this review. In these studies, 11 different physical examination tests were identified. Due to differences in study types, different patient populations, and methodological quality, meta-analysis was not indicated. Presently, most physical examination tests have not been evaluated sufficiently enough to be confident in their ability to either confirm or rule out a PCL tear. The diagnostic accuracy of physical examination tests to assess the integrity of the PCL is largely unknown. There is a strong need for further research in this area. Level of Evidence Diagnosis, level 3a.

Two methodologies for physical penetration testing using social engineering

NARCIS (Netherlands)

Dimkov, T.; Pieters, Wolter; Hartel, Pieter H.

2009-01-01

During a penetration test on the physical security of an organization, if social engineering is used, the penetration tester directly interacts with the employees. These interactions are usually based on deception and if not done properly can upset the employees, violate their privacy or damage

Measuring damage in physical model tests of rubble mounds

NARCIS (Netherlands)

Hofland, B.; Rosa-Santos, Paulo; Taveira-Pinto, Francisco; Lemos, Rute; Mendonça, A.; Juana Fortes, C

2017-01-01

This paper studies novel ways to evaluate armour damage in physical models of coastal structures. High-resolution damage data for reference rubble mound breakwaters obtained under the HYDRALAB+ joint-research project are analysed and discussed. These tests are used to analyse the way to describe

Sacubitril/Valsartan: Effect on Walking Test and Physical Capability.

Science.gov (United States)

Sgorbini, Luca; Rossetti, Antonella; Galati, Alfonso

The 6-min walk test (6MWT) is a simple and inexpensive exercise test to evaluate physical functional capacity that is widely used in heart failure (HF) patients. With the 6MWT, a distance 50 m is considered clinically relevant. To our knowledge, information on improvement in physical functional capacity with sacubitril/valsartan, as assessed by the 6MWT, is still scant. In our daily practice, we apply this test to all patients whenever possible; therefore, we report here the findings observed in a small series of 5 patients with HF with reduced ejection fraction after a 1-month treatment with sacubitril/valsartan at full dose. The mean distance walked on the 6MWT at baseline was 129 m (±64 SD), and this value increased to 436 m (±156) after 1 month of therapy with sacubitril/valsartan 97/103 mg b.i.d. The mean difference from baseline was 305 m (±110). According to these preliminary findings, in clinical practice, a 1-month therapy of sacubitril/valsartan optimized at a 97/103-mg b.i.d. dose appears to be associated with a relevant improvement in the 6MWT. © 2017 S. Karger AG, Basel.

78 FR 6400 - Results of FAA Nitrous Oxide BLEVE Characterization Testing

Science.gov (United States)

2013-01-30

... DEPARTMENT OF TRANSPORTATION Federal Aviation Administration Results of FAA Nitrous Oxide BLEVE Characterization Testing AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of public... FAA sponsored testing of nitrous oxide (N 2 O) characteristics. Nitrous oxide is an important oxidizer...

Initial characterization of the ATR [Advanced Test Reactor] Large Gamma Facility

International Nuclear Information System (INIS)

Schnitzler, B.G.; Rogers, J.W.

1986-05-01

Radiation fields in the ATR Large Gamma Facility test volume are characterized. The preliminary characterization efforts described in this report include total dose rate measurements in the facility, development of a simple methodology for calculating radiation fields from the ATR fuel element power histories, and a comparison of the measured and calculated values

Advanced ceramic composite for high energy resistors. Characterization of electrical and physical properties

International Nuclear Information System (INIS)

Farrokh, Fattahi; Navid, Tagizadegan; Naser, Tabatabaei

2005-01-01

Full text : There is a need to characterize and apply advanced materials to improve the performance of components used in pulse power systems. One area for innovation is the use of bulk electrically conductive ceramics for non-inductive, high energy and high power electrical resistors. Standard Ceramics, Inc. has developed a unique silicon carbide structural ceramic composite which exhibits electrical conductivity. The new conductive bulk ceramic material has a controlled microstructure, which results an improved homogeneity, making the material suitable for use as a non-inductive, high energy resistor. The new material has higher density, highee peak of temperature limit and greater physical strength compared with bulk ceramics currently used for pulsed power resistors. This paper describes characterization of the material's physical and electrical properties and relates them to improvements in low-power density, as compared to existing components would be expected and derived from specific properties such as good thermal conductivity, high strength, thermal shock resistance and high temperature capability. The bulk resistor approach that weas proposed offers high reliability through better mechanical properties and simplicity of construction

Diatomite based ceramics macro- and microscopic characterization

Science.gov (United States)

Aderdour, H.; Bentayeb, A.; Nadiri, A.; Ouammou, A.; Sangleboeuf, J.-C.; Lucas-Girot, A.; Carel, C.

2005-03-01

A Moroccan diatomite is characterized chemically and physically. Mechanical properties of ceramics prepared by sintering at different temperatures ranging from 1050 to 1350° C are studied. Compressive strength and Young modulus are determined by compression tests. Densification and evolution of the microstructure are followed by SEM and other tests.

The physical therapy profile questionnaire (PTPQ): development, validation and pilot testing.

Science.gov (United States)

Dizon, Janine Margarita R; Grimmer-Somers, Karen; Kumar, Saravana

2011-09-19

Country by country similarities and differences in physical therapy practice exists. Therefore, before updates in practice can be provided, such as trainings in evidence-based practice, it is necessary to identify the profile and nature of practice in a given country or setting. Following a search of the international literature, no appropriate tool was identified to collect and establish data to create the profile of physical therapy practice in the Philippines. We therefore developed, validated and pilot tested a survey instrument which would comprehensively describe the practice of physical therapy in the Philippines We used a mixed methods design to answer our study aims. A focus group interview was conducted among a group of physical therapists to establish the content and contexts of items to be included in the survey instrument. Findings were amalgamated with the information from the literature on developing survey instruments/questionnaires. A survey instrument was drafted and named as the Physical Therapy Profile Questionnaire (PTPQ). The PTPQ was then validated and pilot tested to a different group of physical therapists.The final version consisted of five separate parts namely (A) General information and demographics, (B) Practice Profile, (C) Treatment Preferences, (D) Bases for clinical work and (E) Bases for educational/research work. At present the PTPQ is relevant to the Philippines and could be used by any country which has a similar nature of practice with the Philippines. The Physical Therapy Practice Questionnaire (PTPQ) was shown to have good face and content validity among the Filipino physical therapists and their context of practice. It has also been found to be useful, easy to administer tool and in a format appealing to respondents. The PTPQ is expected to assist comprehensive data collection to create a profile of physical therapy practice in the Philippines.

The physical therapy profile questionnaire (PTPQ: development, validation and pilot testing

Directory of Open Access Journals (Sweden)

Grimmer-Somers Karen

2011-09-01

Full Text Available Abstract Background Country by country similarities and differences in physical therapy practice exists. Therefore, before updates in practice can be provided, such as trainings in evidence-based practice, it is necessary to identify the profile and nature of practice in a given country or setting. Following a search of the international literature, no appropriate tool was identified to collect and establish data to create the profile of physical therapy practice in the Philippines. We therefore developed, validated and pilot tested a survey instrument which would comprehensively describe the practice of physical therapy in the Philippines Findings We used a mixed methods design to answer our study aims. A focus group interview was conducted among a group of physical therapists to establish the content and contexts of items to be included in the survey instrument. Findings were amalgamated with the information from the literature on developing survey instruments/questionnaires. A survey instrument was drafted and named as the Physical Therapy Profile Questionnaire (PTPQ. The PTPQ was then validated and pilot tested to a different group of physical therapists. The final version consisted of five separate parts namely (A General information and demographics, (B Practice Profile, (C Treatment Preferences, (D Bases for clinical work and (E Bases for educational/research work. At present the PTPQ is relevant to the Philippines and could be used by any country which has a similar nature of practice with the Philippines. Conclusion The Physical Therapy Practice Questionnaire (PTPQ was shown to have good face and content validity among the Filipino physical therapists and their context of practice. It has also been found to be useful, easy to administer tool and in a format appealing to respondents. The PTPQ is expected to assist comprehensive data collection to create a profile of physical therapy practice in the Philippines.

A study on the effect of gamma background in low power startup physics tests

International Nuclear Information System (INIS)

Bae, Chang Joon; Lee, Ki Bog

1993-01-01

Low power physics tests should be performed for the domestic pressurized light water reactors (PWRs) after refueling. The tests are performed to ensure that operating characteristics of the core are consistent with predictions and that the core can be operated as designed. But in some low power physics tests, slow but steady reactivity increasing phenomena were noticed after step reactivity insertion by the control rod movement. These reactivity increasing phenomena are due to the low flux level and the gamma backgroud because an uncompensated ion chamber (UIC) is used as the ex-core neutron detector. The gamma background may affect the results of the low power physics tests. The aims of this paper are to analyze the grounds of such phenomena, to simulate a reference bank worth measurement test and to present a resolution quantitatively. In this study, the gamma background level was estimated by numerically solving the point kinetics equations accounting the gamma background effect. The reactivity computer check test was simulated to verify the model. Also, an appropriate neutron flux level was determined by simulating the reference bank worth measurement test. The determined neutron flux level is approximately 0.3 of the nuclear heating flux. This level is about 3 times as high as the current test upper limit specified in the test procedure. Then, the findings from this work were successfully applied to Kori unit 4 cycle 7 and Yonggwang unit 1 cycle 7 physics tests. (Author)

Construction and characterization of external cavity diode lasers for atomic physics.

Science.gov (United States)

Hardman, Kyle S; Bennetts, Shayne; Debs, John E; Kuhn, Carlos C N; McDonald, Gordon D; Robins, Nick

2014-04-24

Since their development in the late 1980s, cheap, reliable external cavity diode lasers (ECDLs) have replaced complex and expensive traditional dye and Titanium Sapphire lasers as the workhorse laser of atomic physics labs. Their versatility and prolific use throughout atomic physics in applications such as absorption spectroscopy and laser cooling makes it imperative for incoming students to gain a firm practical understanding of these lasers. This publication builds upon the seminal work by Wieman, updating components, and providing a video tutorial. The setup, frequency locking and performance characterization of an ECDL will be described. Discussion of component selection and proper mounting of both diodes and gratings, the factors affecting mode selection within the cavity, proper alignment for optimal external feedback, optics setup for coarse and fine frequency sensitive measurements, a brief overview of laser locking techniques, and laser linewidth measurements are included.

Earth-based construction material field tests characterization in the Alto Douro Wine Region

Science.gov (United States)

Cardoso, Rui; Pinto, Jorge; Paiva, Anabela; Lanzinha, João Carlos

2017-12-01

The Alto Douro Wine Region, located in the northeast of Portugal, a UNESCO World Heritage Site, presents an abundant vernacular building heritage. This building technology is based on a timber framed structure filled with a composite earth-based material. A lack of scientific studies related to this technology is evident, furthermore, principally in rural areas, this traditional building stock is highly deteriorated and damaged because of the rareness of conservation and strengthening works, which is partly related to the non-engineered character of this technology and to the knowledge loosed on that technique. Those aspects motivated the writing of this paper, whose main purpose is the physical and chemical characterization of the earth-based material applied in the tabique buildings of that region through field tests. Consequently, experimental work was conducted and the results obtained allowed, among others, the proposal of a series of adequate field tests. At our knowledge, this is the first time field tests are undertaken for tabique technology. This information will provide the means to assess the suitability of a given earth-based material with regards to this technology. The knowledge from this study could also be very useful for the development of future normative documents and as a reference for architects and engineers that work with this technology to guide and regulate future conservation, rehabilitation or construction processes helping to preserve this important legacy.

Benchmark and physics testing of LIFE-4C. Summary

International Nuclear Information System (INIS)

Liu, Y.Y.

1984-06-01

LIFE-4C is a steady-state/transient analysis code developed for performance evaluation of carbide [(U,Pu)C and UC] fuel elements in advanced LMFBRs. This paper summarizes selected results obtained during a crucial step in the development of LIFE-4C - benchmark and physics testing

The relationship between history and physical examination findings and the outcome of electrodiagnostic testing in patients with sciatica referred to physical therapy.

Science.gov (United States)

Savage, Nathan J; Fritz, Julie M; Thackeray, Anne

2014-07-01

Cross-sectional diagnostic accuracy study. To investigate the relationship between history and physical examination findings and the outcome of electrodiagnostic testing in patients with sciatica referred to physical therapy. Electrodiagnostic testing is routinely used to evaluate patients with sciatica. Recent evidence suggests that the presence of radiculopathy identified with electrodiagnostic testing may predict better functional outcomes in these patients. While some patient history and physical examination findings have been shown to predict the presence of disc herniation or neurological insult, little is known about their relationship to the results of electrodiagnostic testing. Electrodiagnostic testing was performed on 38 patients with sciatica who participated in a randomized trial that compared different physical therapy interventions. The diagnostic gold standard was the presence or absence of radiculopathy, based on the results of the needle electromyographic examination. Diagnostic sensitivity and specificity values were calculated, along with corresponding likelihood ratios, for select patient history and physical examination variables. No significant relationship was found between select patient history and physical examination findings, analyzed individually or in combination, and the outcome of electrodiagnostic testing. Diagnostic sensitivity values ranged from 0.03 (95% confidence interval [CI]: 0.00, 0.24) to a high of 0.95 (95% CI: 0.72, 0.99), and specificity values ranged from 0.10 (95% CI: 0.02, 0.34) to a high of 0.95 (95% CI: 0.72, 0.99). Positive likelihood ratios ranged from 0.15 (95% CI: 0.01, 2.87) to a high of 2.33 (95% CI: 0.71, 7.70), and negative likelihood ratios ranged from 2.00 (95% CI: 0.35, 11.48) to a low of 0.50 (95% CI: 0.03, 8.10). In this investigation, the relationship between patient history and physical examination findings and the outcome of electrodiagnostic testing among patients with sciatica was not found to be

Physicists purchase materials testing machine in support of pioneering particle physics experiments

CERN Multimedia

Sharpe, Suzanne

2007-01-01

"The particle physics group at Liverpool University has purchased an LRXPlus singlecolumn materials testing machine from Lloyd Instruments, which will be used to help characterise the carbon-fibre support frames for detectors used for state-of-the-art particle physics experiments." (1 page)

Stereotype threat? Effects of inquiring about test takers' gender on conceptual test performance in physics

Science.gov (United States)

Maries, Alexandru; Singh, Chandralekha

2015-12-01

It has been found that activation of a stereotype, for example by indicating one's gender before a test, typically alters performance in a way consistent with the stereotype, an effect called "stereotype threat." On a standardized conceptual physics assessment, we found that asking test takers to indicate their gender right before taking the test did not deteriorate performance compared to an equivalent group who did not provide gender information. Although a statistically significant gender gap was present on the standardized test whether or not students indicated their gender, no gender gap was observed on the multiple-choice final exam students took, which included both quantitative and conceptual questions on similar topics.

Battery designs the testing physical of skills for selecting talented taekwondo

Directory of Open Access Journals (Sweden)

Mohammed Mustafa Bakr

2016-07-01

Full Text Available The aim of this study is to design a battery test physical of skill for the selection of talented young taekwondo Egyptian national project for may have a practical importance of overseeing the selection of young people as well as in the planning of the training process to reach high levels. Applied study on a sample of (750 Individual clubs and youth centers in 14 countries in the Arab Republic of Egypt, and the average age of (11.11 ± 1.06 years, height (143.50 ± 11,09 cm and weight (42.53 ±10,74kg. Tests were conducted in the period from 17/11/2012 to 29/12/2012. Physical tests following (Ability, Hinge flexibility basin, Agility, Kinetics speed in a level trunk, Kinetics speed in the level face, Endure Performance. Scientific transactions testing laboratories account sincerity and consistency of the tests used in the study. Where the value of the coefficient of sincerity d statistically at the level of the significance of 0.05 is a sign the two sides between the high level and the low level as the value of the coefficient of sincerity between (0.682, 0.932, which indicates that the tests measure what it was made. It was also correlation coefficient d statistically at the level of an indication (0.01 and (0.05 is a sign of the two parties, where the value of P < 0.05 in all tests as they ranged between (0.964-0.998, pointing to a flat these tests. The researcher used the descriptive survey method. Calculated using the weight of the medical balance and use a tape measure to the nearest (0.5 cm. The statistical analysis SPSS was used to apply formulas statistical by calculating: average, standard deviation, correlation, Factor analysis, Six Sigma Score, percentile scores. The results of the standard levels the battery test of physical skills extracted the selection of talented taekwondo sports in the factors of grace the second factor is the dynamic speed. The study concluded that this study concluded to a battery physical of skill tests for

Characterization of Ceramic Material Produced From a Cold Crucible Induction Melter Test

Energy Technology Data Exchange (ETDEWEB)

Amoroso, J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Marra, J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2015-04-30

This report summarizes the results from characterization of samples from a melt processed surrogate ceramic waste form. Completed in October of 2014, the first scaled proof of principle cold crucible induction melter (CCIM) test was conducted to process a Fe-hollandite-rich titanate ceramic for treatment of high level nuclear waste. X-ray diffraction, electron microscopy, inductively coupled plasma-atomic emission spectroscopy (and inductively coupled plasma-mass spectroscopy for Cs), and product consistency tests were used to characterize the CCIM material produced. Core samples at various radial locations from the center of the CCIM were taken. These samples were also sectioned and analyzed vertically. Together, the various samples were intended to provide an indication of the homogeneity throughout the CCIM with respect to phase assemblage, chemical composition, and chemical durability. Characterization analyses confirmed that a crystalline ceramic with desirable phase assemblage was produced from a melt using a CCIM. Hollandite and zirconolite were identified in addition to possible highly-substituted pyrochlore and perovskite. Minor phases rich in Fe, Al, or Cs were also identified. Remarkably only minor differences were observed vertically or radially in the CCIM material with respect to chemical composition, phase assemblage, and durability. This recent CCIM test and the resulting characterization in conjunction with demonstrated compositional improvements support continuation of CCIM testing with an improved feed composition and improved melter system.

Feasibility and reliability of physical fitness tests in older adults with intellectual disability : A pilot study

NARCIS (Netherlands)

Hilgenkamp, Thessa I. M.; van Wijck, Ruud; Evenhuis, Heleen M.

Background Physical fitness is relevant for wellbeing and health, but knowledge on the feasibility and reliability of instruments to measure physical fitness for older adults with intellectual disability is lacking. Methods Feasibility and test-retest reliability of a physical fitness test battery

Characterization and Beam Tests Results of Non-Uniformly Irradiated 3D Pixel Sensors for HEP Experiments

International Nuclear Information System (INIS)

Lopez, I.; Grinstein, S.; Micelli, A.; Tsiskaridze, S.

2013-06-01

3D Pixel detectors, with cylindrical electrodes that penetrate the silicon substrate, offer advantages over standard planar sensors in terms of radiation hardness, since the charge collection distance can be reduced independently of the bulk thickness. In the framework of the ATLAS Forward Physics (AFP) program, work has been carried out to study the suitability of 3D pixel devices for forward proton tracking. The AFP tracker unit will consist of an array of five pixel sensors placed at 2-3 mm from the Large Hadron Collider (LHC) proton beam. The proximity to the beam is essential for the AFP physics program as it directly increases the sensitivity of the experiment. Thus, there are two critical requirements for the AFP pixel detector. First, the dead region of the sensor has to be minimized. Second, the device has to be able to cope with a very inhomogeneous radiation distribution. Recent results of the characterization and beam test studies of in-homogeneously irradiated 3D pixel sensors produced at CNM-Barcelona will be presented. (authors)

Student Motivation Associated with Fitness Testing in the Physical Education Context

Science.gov (United States)

Jaakkola, Timo Tapio; Sääkslahti, Arja; Yli-Piipari, Sami; Manninen, Mika; Watt, Anthony; Liukkonen, Jarmo

2013-01-01

The purpose of the study was to analyze students' motivation in relation to their participation in fitness testing classes. Participants were 134 Finnish Grade 5 and 8 students. Students completed the contextual motivation and perceived physical competence scales before the fitness testing class and the situational motivation questionnaire…

Preliminary analyses for HTTR's start-up physics tests by Monte Carlo code MVP

International Nuclear Information System (INIS)

Nojiri, Naoki; Nakano, Masaaki; Ando, Hiroei; Fujimoto, Nozomu; Takeuchi, Mitsuo; Fujisaki, Shingo; Yamashita, Kiyonobu

1998-08-01

Analyses of start-up physics tests for High Temperature Engineering Test Reactor (HTTR) have been carried out by Monte Carlo code MVP based on continuous energy method. Heterogeneous core structures were modified precisely, such as the fuel compacts, fuel rods, coolant channels, burnable poisons, control rods, control rod insertion holes, reserved shutdown pellet insertion holes, gaps between graphite blocks, etc. Such precise modification of the core structures was difficult with diffusion calculation. From the analytical results, the followings were confirmed; The first criticality will be achieved around 16 fuel columns loaded. The reactivity at the first criticality can be controlled by only one control rod located at the center of the core with other fifteen control rods fully withdrawn. The excess reactivity, reactor shutdown margin and control rod criticality positions have been evaluated. These results were used for planning of the start-up physics tests. This report presents analyses of start-up physics tests for HTTR by MVP code. (author)

Diagnostic accuracy of scapular physical examination tests for shoulder disorders: a systematic review.

Science.gov (United States)

Wright, Alexis A; Wassinger, Craig A; Frank, Mason; Michener, Lori A; Hegedus, Eric J

2013-09-01

To systematically review and critique the evidence regarding the diagnostic accuracy of physical examination tests for the scapula in patients with shoulder disorders. A systematic, computerised literature search of PubMED, EMBASE, CINAHL and the Cochrane Library databases (from database inception through January 2012) using keywords related to diagnostic accuracy of physical examination tests of the scapula. The Quality Assessment of Diagnostic Accuracy Studies tool was used to critique the quality of each paper. Eight articles met the inclusion criteria; three were considered to be of high quality. Of the three high-quality studies, two were in reference to a 'diagnosis' of shoulder pain. Only one high-quality article referenced specific shoulder pathology of acromioclavicular dislocation with reported sensitivity of 71% and 41% for the scapular dyskinesis and SICK scapula test, respectively. Overall, no physical examination test of the scapula was found to be useful in differentially diagnosing pathologies of the shoulder.

PHYSICAL CHARACTERIZATION OF VITREOUS STATE LABORATORY AY102/C106 AND AZ102 HIGH LEVEL WASTE MELTER FEED SIMULANTS (U)

Energy Technology Data Exchange (ETDEWEB)

Hansen, E

2005-03-31

The objective of this task is to characterize and report specified physical properties and pH of simulant high level waste (HLW) melter feeds (MF) processed through the scaled melters at Vitreous State Laboratories (VSL). The HLW MF simulants characterized are VSL AZ102 straight hydroxide melter feed, VSL AZ102 straight hydroxide rheology adjusted melter feed, VSL AY102/C106 straight hydroxide melter feed, VSL AY102/C106 straight hydroxide rheology adjusted melter feed, and Savannah River National Laboratory (SRNL) AY102/C106 precipitated hydroxide processed sludge blended with glass former chemicals at VSL to make melter feed. The physical properties and pH were characterized using the methods stated in the Waste Treatment Plant (WTP) characterization procedure (Ref. 7).

Construction and Characterization of External Cavity Diode Lasers for Atomic Physics

Science.gov (United States)

Hardman, Kyle S.; Bennetts, Shayne; Debs, John E.; Kuhn, Carlos C. N.; McDonald, Gordon D.; Robins, Nick

2014-01-01

Since their development in the late 1980s, cheap, reliable external cavity diode lasers (ECDLs) have replaced complex and expensive traditional dye and Titanium Sapphire lasers as the workhorse laser of atomic physics labs1,2. Their versatility and prolific use throughout atomic physics in applications such as absorption spectroscopy and laser cooling1,2 makes it imperative for incoming students to gain a firm practical understanding of these lasers. This publication builds upon the seminal work by Wieman3, updating components, and providing a video tutorial. The setup, frequency locking and performance characterization of an ECDL will be described. Discussion of component selection and proper mounting of both diodes and gratings, the factors affecting mode selection within the cavity, proper alignment for optimal external feedback, optics setup for coarse and fine frequency sensitive measurements, a brief overview of laser locking techniques, and laser linewidth measurements are included. PMID:24796259

Characterizing the Performance of the Princeton Advanced Test Stand Ion Source

Science.gov (United States)

Stepanov, A.; Gilson, E. P.; Grisham, L.; Kaganovich, I.; Davidson, R. C.

2012-10-01

The Princeton Advanced Test Stand (PATS) is a compact experimental facility for studying the physics of intense beam-plasma interactions relevant to the Neutralized Drift Compression Experiment - II (NDCX-II). The PATS facility consists of a multicusp RF ion source mounted on a 2 m-long vacuum chamber with numerous ports for diagnostic access. Ar+ beams are extracted from the source plasma with three-electrode (accel-decel) extraction optics. The RF power and extraction voltage (30 - 100 kV) are pulsed to produce 100 μsec duration beams at 0.5 Hz with excellent shot-to-shot repeatability. Diagnostics include Faraday cups, a double-slit emittance scanner, and scintillator imaging. This work reports measurements of beam parameters for a range of beam energies (30 - 50 keV) and currents to characterize the behavior of the ion source and extraction optics. Emittance scanner data is used to calculate the beam trace-space distribution and corresponding transverse emittance. If the plasma density is changing during a beam pulse, time-resolved emittance scanner data has been taken to study the corresponding evolution of the beam trace-space distribution.

Application of physical and chemical characterization techniques to metallic powders

International Nuclear Information System (INIS)

Slotwinski, J. A.; Watson, S. S.; Stutzman, P. E.; Ferraris, C. F.; Peltz, M. A.; Garboczi, E. J.

2014-01-01

Systematic studies have been carried out on two different powder materials used for additive manufacturing: stainless steel and cobalt-chrome. The characterization of these powders is important in NIST efforts to develop appropriate measurements and standards for additive materials and to document the property of powders used in a NIST-led additive manufacturing material round robin. An extensive array of characterization techniques was applied to these two powders, in both virgin and recycled states. The physical techniques included laser diffraction particle size analysis, X-ray computed tomography for size and shape analysis, and optical and scanning electron microscopy. Techniques sensitive to chemistry, including X-ray diffraction and energy dispersive analytical X-ray analysis using the X-rays generated during scanning electron microscopy, were also employed. Results of these analyses will be used to shed light on the question: how does virgin powder change after being exposed to and recycled from one or more additive manufacturing build cycles? In addition, these findings can give insight into the actual additive manufacturing process

Simulating direct shear tests with the Bullet physics library: A validation study.

Science.gov (United States)

Izadi, Ehsan; Bezuijen, Adam

2018-01-01

This study focuses on the possible uses of physics engines, and more specifically the Bullet physics library, to simulate granular systems. Physics engines are employed extensively in the video gaming, animation and movie industries to create physically plausible scenes. They are designed to deliver a fast, stable, and optimal simulation of certain systems such as rigid bodies, soft bodies and fluids. This study focuses exclusively on simulating granular media in the context of rigid body dynamics with the Bullet physics library. The first step was to validate the results of the simulations of direct shear testing on uniform-sized metal beads on the basis of laboratory experiments. The difference in the average angle of mobilized frictions was found to be only 1.0°. In addition, a very close match was found between dilatancy in the laboratory samples and in the simulations. A comprehensive study was then conducted to determine the failure and post-failure mechanism. We conclude with the presentation of a simulation of a direct shear test on real soil which demonstrated that Bullet has all the capabilities needed to be used as software for simulating granular systems.

Development and validation of a musculoskeletal physical examination decision-making test for medical students.

Science.gov (United States)

Bishop, Julie Y; Awan, Hisham M; Rowley, David M; Nagel, Rollin W

2013-01-01

Despite a renewed emphasis among educators, musculoskeletal education is still lacking in medical school and residency training programs. We created a musculoskeletal multiple-choice physical examination decision-making test to assess competency and physical examination knowledge of our trainees. We developed a 20-question test in musculoskeletal physical examination decision-making test with content that most medical students and orthopedic residents should know. All questions were reviewed by ratings of US orthopedic chairmen. It was administered to postgraduate year 2 to 5 orthopedic residents and 2 groups of medical students: 1 group immediately after their 3-week musculoskeletal course and the other 1 year after the musculoskeletal course completion. We hypothesized that residents would score highest, medical students 1 year post-musculoskeletal training lowest, and students immediately post-musculoskeletal training midrange. We administered an established cognitive knowledge test to compare student knowledge base as we expected the scores to correlate. Academic medical center in the Midwestern United States. Orthopedic residents, chairmen, and medical students. Fifty-four orthopedic chairmen (54 of 110 or 49%) responded to our survey, rating a mean overall question importance of 7.12 (0 = Not Important; 5 = Important; 10 = Very Important). Mean physical examination decision-making scores were 89% for residents, 77% for immediate post-musculoskeletal trained medical students, and 59% 1 year post-musculoskeletal trained medical students (F = 42.07, pphysical examination decision-making test was found to be internally consistent (Kuder-Richardson Formula 20 = 0.69). The musculoskeletal cognitive knowledge test was 78% for immediate post-musculoskeletal trained students and 71% for the 1 year post-musculoskeletal trained students. The student physical examination and cognitive knowledge scores were correlated (r = 0.54, pphysical examination decision-making test

Characterization samples of Tigris river water treated with nano colloidal silver (physically, chemically, microbiologically)

International Nuclear Information System (INIS)

Dumboos, H. I.; Beden, S. J.; Zouari, K.; Chkir, N.; Ahmed, H. A.

2012-12-01

Many researches of using nano silver in purification of drinking water from bacteria and its effect on stan dared properties as drinking water were established. Two stages accomplished in these projects. First stage include preparation of colloidal silver with characterization process and prepare water samples through sedimentation, filtration process, PH and turbidity measure then treated with colloidal silver in volume ratio (0.1-Λ) ml/100ml. The second stage represent select the better results from stage one and take samples to determine the standard characterization values with chemical, physical and microbiological taste. Results will be compared with Iraq standard certification. (Author)

Standard guide for characterization of spent nuclear fuel in support of geologic repository disposal

CERN Document Server

American Society for Testing and Materials. Philadelphia

2009-01-01

1.1 This guide provides guidance for the types and extent of testing that would be involved in characterizing the physical and chemical nature of spent nuclear fuel (SNF) in support of its interim storage, transport, and disposal in a geologic repository. This guide applies primarily to commercial light water reactor (LWR) spent fuel and spent fuel from weapons production, although the individual tests/analyses may be used as applicable to other spent fuels such as those from research and test reactors. The testing is designed to provide information that supports the design, safety analysis, and performance assessment of a geologic repository for the ultimate disposal of the SNF. 1.2 The testing described includes characterization of such physical attributes as physical appearance, weight, density, shape/geometry, degree, and type of SNF cladding damage. The testing described also includes the measurement/examination of such chemical attributes as radionuclide content, microstructure, and corrosion product c...

Measurement of Function Post Hip Fracture: Testing a Comprehensive Measurement Model of Physical Function.

Science.gov (United States)

Resnick, Barbara; Gruber-Baldini, Ann L; Hicks, Gregory; Ostir, Glen; Klinedinst, N Jennifer; Orwig, Denise; Magaziner, Jay

2016-07-01

Measurement of physical function post hip fracture has been conceptualized using multiple different measures. This study tested a comprehensive measurement model of physical function. This was a descriptive secondary data analysis including 168 men and 171 women post hip fracture. Using structural equation modeling, a measurement model of physical function which included grip strength, activities of daily living, instrumental activities of daily living, and performance was tested for fit at 2 and 12 months post hip fracture, and among male and female participants. Validity of the measurement model of physical function was evaluated based on how well the model explained physical activity, exercise, and social activities post hip fracture. The measurement model of physical function fit the data. The amount of variance the model or individual factors of the model explained varied depending on the activity. Decisions about the ideal way in which to measure physical function should be based on outcomes considered and participants. The measurement model of physical function is a reliable and valid method to comprehensively measure physical function across the hip fracture recovery trajectory. © 2015 Association of Rehabilitation Nurses.

CHARACTERIZATION AND ACTUAL WASTE TEST WITH TANK 5F SAMPLES

International Nuclear Information System (INIS)

Fletcher, D.

2007-01-01

The initial phase of bulk waste removal operations was recently completed in Tank 5F. Video inspection of the tank indicates several mounds of sludge still remain in the tank. Additionally, a mound of white solids was observed under Riser 5. In support of chemical cleaning and heel removal programs, samples of the sludge and the mound of white solids were obtained from the tank for characterization and testing. A core sample of the sludge and Super Snapper sample of the white solids were characterized. A supernate dip sample from Tank 7F was also characterized. A portion of the sludge was used in two tank cleaning tests using oxalic acid at 50 C and 75 C. The filtered oxalic acid from the tank cleaning tests was subsequently neutralized by addition to a simulated Tank 7F supernate. Solids and liquid samples from the tank cleaning test and neutralization test were characterized. A separate report documents the results of the gas generation from the tank cleaning test using oxalic acid and Tank 5F sludge. The characterization results for the Tank 5F sludge sample (FTF-05-06-55) appear quite good with respect to the tight precision of the sample replicates, good results for the glass standards, and minimal contamination found in the blanks and glass standards. The aqua regia and sodium peroxide fusion data also show good agreement between the two dissolution methods. Iron dominates the sludge composition with other major contributors being uranium, manganese, nickel, sodium, aluminum, and silicon. The low sodium value for the sludge reflects the absence of supernate present in the sample due to the core sampler employed for obtaining the sample. The XRD and CSEM results for the Super Snapper salt sample (i.e., white solids) from Tank 5F (FTF-05-07-1) indicate the material contains hydrated sodium carbonate and bicarbonate salts along with some aluminum hydroxide. These compounds likely precipitated from the supernate in the tank. A solubility test showed the material

Measurement of talent in team handball: the questionable use of motor and physical tests.

Science.gov (United States)

Lidor, Ronnie; Falk, Bareket; Arnon, Michal; Cohen, Yoram; Segal, Gil; Lander, Yael

2005-05-01

Testing for selection is one of the most important fundamentals in any multistep sport program. In most ball games, coaches assess motor, physical, and technical skills on a regular basis in early stages of talent identification and development. However, selection processes are complex, are often unstructured, and lack clear-cut theory-based knowledge. For example, little is known about the relevance of the testing process to the final selection of the young prospects. The purpose of this study was to identify motor, physical, and skill variables that could provide coaches with relevant information in the selection process of young team handball players. In total, 405 players (12-13 years of age at the beginning of the testing period) were recommended by their coaches to undergo a battery of tests prior to selection to the Junior National Team. This number is the sum of all players participating in the different phases of the program. However, not all of them took part in each testing phase. The battery included physical measurements (height and weight), a 4 x 10-m running test, explosive power tests (medicine ball throw and standing long jump), speed tests (a 20-m sprint from a standing position and a 20-m sprint with a flying start), and a slalom dribbling test. Comparisons between those players eventually selected to the Junior National Team 2-3 years later with those not selected demonstrated that only the skill test served as a good indicator. In all other measurements, a wide overlap could be seen between the results of the selected and nonselected players. It is suggested that future studies investigate the usefulness of tests reflecting more specific physical ability and cognitive characteristics.

Mixed waste characterization and certification at the Nevada Test Site

International Nuclear Information System (INIS)

Kawamura, T.A.; Dodge, R.L.; Fitzsimmons, P.K.

1988-01-01

The Radioactive Waste Management Project at the Nevada Test Site (NTS) was recently granted interim status by the state of Nevada to receive mixed waste. The RCRA Part B permit application has been revised and submitted to the state. Preliminary indications are that the permit will be granted. In conjunction with revision of the Part B permit application, pertinent DOE guidelines governing waste acceptance criteria and waste characterization were also revised. The guidelines balance the need for full characterization of hazardous constituents with ALARA precepts. Because it is not always feasible to obtain a full chemical analysis without undue or unnecessary radiological exposure of personnel, process knowledge is considered an acceptable method of waste characterization. A balance of administrative controls and verification procedures, as well as careful documentation and high standards of quality assurance, are essential to the characterization and certification program developed for the NTS

Initial Characterization of Colombian High School Physics Teachers' Pedagogical Content Knowledge on Electric Fields

Science.gov (United States)

Melo-Niño, Lina Viviana; Cañada, Florentina; Mellado, Vicente

2017-02-01

We explore the initial characterization of the pedagogical content knowledge of four, in-service, Colombian pre-university secondary education physics teachers on the concept of electric field. Two of them teach the content in English as a second language. The aim of the study was to obtain an image of the participants' teaching of electric field and the inherent complexities that go with that. The results revealed that factors which involved their personal educational models, such as, how they interpret their school's curriculum, the relationship they see between physics and mathematics, the most effective strategies for teaching physics, and the time they have available to develop the topic played a significant role. The teachers considered it essential to establish new strategies that would motivate the pupils by helping them visualize the electric field.

Characterizing the epistemological development of physics majors

Directory of Open Access Journals (Sweden)

Elizabeth Gire

2009-02-01

Full Text Available Students in introductory physics courses are likely to have views about physics that differ from those of experts. However, students who continue to study physics eventually become experts themselves. Presumably these students either possess or develop more expertlike views. To investigate this process, the views of introductory physics students majoring in physics are compared with the views of introductory physics students majoring in engineering. In addition, the views of physics majors are assessed at various stages of degree progress. The Colorado learning attitudes about science survey is used to evaluate students’ views about physics, and students’ overall survey scores and responses to individual survey items are analyzed. Beginning physics majors are significantly more expertlike than nonmajors in introductory physics courses, and this high level of sophistication is consistent for most of undergraduate study.

Earth-based construction material field tests characterization in the Alto Douro Wine Region

Directory of Open Access Journals (Sweden)

Cardoso Rui

2017-12-01

Full Text Available The Alto Douro Wine Region, located in the northeast of Portugal, a UNESCO World Heritage Site, presents an abundant vernacular building heritage. This building technology is based on a timber framed structure filled with a composite earth-based material. A lack of scientific studies related to this technology is evident, furthermore, principally in rural areas, this traditional building stock is highly deteriorated and damaged because of the rareness of conservation and strengthening works, which is partly related to the non-engineered character of this technology and to the knowledge loosed on that technique. Those aspects motivated the writing of this paper, whose main purpose is the physical and chemical characterization of the earth-based material applied in the tabique buildings of that region through field tests. Consequently, experimental work was conducted and the results obtained allowed, among others, the proposal of a series of adequate field tests. At our knowledge, this is the first time field tests are undertaken for tabique technology. This information will provide the means to assess the suitability of a given earth-based material with regards to this technology. The knowledge from this study could also be very useful for the development of future normative documents and as a reference for architects and engineers that work with this technology to guide and regulate future conservation, rehabilitation or construction processes helping to preserve this important legacy.

Reliability of Health-Related Physical Fitness Tests among Colombian Children and Adolescents: The FUPRECOL Study.

Directory of Open Access Journals (Sweden)

Robinson Ramírez-Vélez

Full Text Available Substantial evidence indicates that youth physical fitness levels are an important marker of lifestyle and cardio-metabolic health profiles and predict future risk of chronic diseases. The reliability physical fitness tests have not been explored in Latino-American youth population. This study's aim was to examine the reliability of health-related physical fitness tests that were used in the Colombian health promotion "Fuprecol study". Participants were 229 Colombian youth (boys n = 124 and girls n = 105 aged 9 to 17.9 years old. Five components of health-related physical fitness were measured: 1 morphological component: height, weight, body mass index (BMI, waist circumference, triceps skinfold, subscapular skinfold, and body fat (% via impedance; 2 musculoskeletal component: handgrip and standing long jump test; 3 motor component: speed/agility test (4x10 m shuttle run; 4 flexibility component (hamstring and lumbar extensibility, sit-and-reach test; 5 cardiorespiratory component: 20-meter shuttle-run test (SRT to estimate maximal oxygen consumption. The tests were performed two times, 1 week apart on the same day of the week, except for the SRT which was performed only once. Intra-observer technical errors of measurement (TEMs and inter-rater (reliability were assessed in the morphological component. Reliability for the Musculoskeletal, motor and cardiorespiratory fitness components was examined using Bland-Altman tests. For the morphological component, TEMs were small and reliability was greater than 95% of all cases. For the musculoskeletal, motor, flexibility and cardiorespiratory components, we found adequate reliability patterns in terms of systematic errors (bias and random error (95% limits of agreement. When the fitness assessments were performed twice, the systematic error was nearly 0 for all tests, except for the sit and reach (mean difference: -1.03% [95% CI = -4.35% to -2.28%]. The results from this study indicate that the

Microsensors for In-situ Chemical, Physical and Radiological Characterization of Mixed Waste (73808)

International Nuclear Information System (INIS)

Thundat, Thomas G.

2004-01-01

Portable, real-time, in-situ chemical, physical, and radiological sensors for the characterization and monitoring of transuranic waste, mixed waste, ground water, contaminated soil, and process streams are needed within the DOE complex. A continuation of this basic research program is proposed to study the influence of control of the electrochemical potential of a metallic coating on a microcantilever as a means of developing specific and highly sensitive sensors. Basic research will be needed to understand the influence of variation of electrochemical potential on the bending of cantilevers in an electrolyte solution. Changes in the chemical potential of a metal-electrolyte interface, affected by changing the applied potential, leads to a change in the depletion or accumulation of substances at the interface. This change in the surface excess at the interface is reflected in a change in the interfacial tension, which is sensitively detected as cantilever deflection. Deposition of electroactive heavy metals as well as the adsorption of metal oxide species will be detectable as a cantilever bending. We plan to continue field-testing cantilever sensors at DOE sites as appropriate. Practical sensors for Hg and CrO4 -2 have been developed, and the former has been field tested. A sensor for large poorly hydrated anions (ClO4 -, ReO4 -, TcO4 -) based on a quarternary ammonium SAM coating is under development and will be field tested when appropriate. The advantage of cantilever sensors is that once the basic platform is developed, it can be the basis for a plethora of inexpensive, miniature sensors. This program will take advantage of advances in cantilever technology made by other programs as well

RF characterization and testing of ridge waveguide transitions for RF power couplers

Energy Technology Data Exchange (ETDEWEB)

Kumar, Rajesh; Jose, Mentes; Singh, G.N. [Ion Accelerator Development Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Kumar, Girish [Department of Electrical Engineering, IIT Bombay, Mumbai 400076,India (India); Bhagwat, P.V. [Ion Accelerator Development Division, Bhabha Atomic Research Centre, Mumbai 400085 (India)

2016-12-01

RF characterization of rectangular to ridge waveguide transitions for RF power couplers has been carried out by connecting them back to back. Rectangular waveguide to N type adapters are first calibrated by TRL method and then used for RF measurements. Detailed information is obtained about their RF behavior by measurements and full wave simulations. It is shown that the two transitions can be characterized and tuned for required return loss at design frequency of 352.2 MHz. This opens the possibility of testing and conditioning two transitions together on a test bench. Finally, a RF coupler based on these transitions is coupled to an accelerator cavity. The power coupler is successfully tested up to 200 kW, 352.2 MHz with 0.2% duty cycle.

Testing a self-determination theory model of children's physical activity motivation: a cross-sectional study.

Science.gov (United States)

Sebire, Simon J; Jago, Russell; Fox, Kenneth R; Edwards, Mark J; Thompson, Janice L

2013-09-26

Understanding children's physical activity motivation, its antecedents and associations with behavior is important and can be advanced by using self-determination theory. However, research among youth is largely restricted to adolescents and studies of motivation within certain contexts (e.g., physical education). There are no measures of self-determination theory constructs (physical activity motivation or psychological need satisfaction) for use among children and no previous studies have tested a self-determination theory-based model of children's physical activity motivation. The purpose of this study was to test the reliability and validity of scores derived from scales adapted to measure self-determination theory constructs among children and test a motivational model predicting accelerometer-derived physical activity. Cross-sectional data from 462 children aged 7 to 11 years from 20 primary schools in Bristol, UK were analysed. Confirmatory factor analysis was used to examine the construct validity of adapted behavioral regulation and psychological need satisfaction scales. Structural equation modelling was used to test cross-sectional associations between psychological need satisfaction, motivation types and physical activity assessed by accelerometer. The construct validity and reliability of the motivation and psychological need satisfaction measures were supported. Structural equation modelling provided evidence for a motivational model in which psychological need satisfaction was positively associated with intrinsic and identified motivation types and intrinsic motivation was positively associated with children's minutes in moderate-to-vigorous physical activity. The study provides evidence for the psychometric properties of measures of motivation aligned with self-determination theory among children. Children's motivation that is based on enjoyment and inherent satisfaction of physical activity is associated with their objectively-assessed physical

Chemical Explosion Experiments to Improve Nuclear Test Monitoring - Developing a New Paradigm for Nuclear Test Monitoring with the Source Physics Experiments (SPE)

International Nuclear Information System (INIS)

Snelson, Catherine M.; Abbott, Robert E.; Broome, Scott T.; Mellors, Robert J.; Patton, Howard J.; Sussman, Aviva J.; Townsend, Margaret J.; Walter, William R.

2013-01-01

A series of chemical explosions, called the Source Physics Experiments (SPE), is being conducted under the auspices of the U.S. Department of Energy's National Nuclear Security Administration (NNSA) to develop a new more physics-based paradigm for nuclear test monitoring. Currently, monitoring relies on semi-empirical models to discriminate explosions from earthquakes and to estimate key parameters such as yield. While these models have been highly successful monitoring established test sites, there is concern that future tests could occur in media and at scale depths of burial outside of our empirical experience. This is highlighted by North Korean tests, which exhibit poor performance of a reliable discriminant, mb:Ms (Selby et al., 2012), possibly due to source emplacement and differences in seismic responses for nascent and established test sites. The goal of SPE is to replace these semi-empirical relationships with numerical techniques grounded in a physical basis and thus applicable to any geologic setting or depth

Initial Characterization of Colombian High School Physics Teachers' Pedagogical Content Knowledge on Electric Fields

Science.gov (United States)

Melo-Niño, Lina Viviana; Cañada, Florentina; Mellado, Vicente

2017-01-01

We explore the initial characterization of the pedagogical content knowledge of four, in-service, Colombian pre-university secondary education physics teachers on the concept of electric field. Two of them teach the content in English as a second language. The aim of the study was to obtain an image of the participants' teaching of electric field…

Mixed waste characterization and certification at the Nevada Test Site

International Nuclear Information System (INIS)

Kawamura, T.A.; Dodge, R.L.; Fitzsimmons, P.K.

1988-01-01

The Radioactive Waste Management Project (RWMP) at the Nevada Test Site (NTS) was recently granted interim status by the state of Nevada to receive mixed waste (MW). The RCRA Part B permit application has been revised and submitted to the state. Preliminary indications are that the permit will be granted. In conjunction with revision of the Part B Permit application, pertinent DOE guidelines governing waste acceptance criteria (WAC) and waste characterization were also revised. The guidelines balance the need for full characterization of hazardous constituents with as low as reasonably achievable (ALARA) precepts. Because it is not always feasible to obtain a full chemical analysis without undue or unnecessary radiological exposure of personnel, process knowledge is considered an acceptable method of waste characterization. A balance of administrative controls and verification procedures, as well as careful documentation and high standards of quality assurance, are essential to the characterization and certification program developed for the NTS

Physical and chemical characterization of the (Th, U)O2 mixed oxide fuel

International Nuclear Information System (INIS)

Santos, A.M.M. dos; Avelar, M.M.; Palmieri, H.E.L.; Lameiras, F.S.; Ferreira, R.A.N.

1986-01-01

The NUCLEBRAS R and D Center (Centro de Desenvolvimento da Tecnologia Nuclear - CDTN) has been performing, together with german institutions (Kernforschungsanlage Julich GmbH - KFA, Krafwerk Union A.G. - KWU and NUKEM GmbH), a program for utilization of thorium in pressurized water reactors. In this paper are presented the physical and chemical characterizations necessary to quality the (Th, U)O 2 fuel and the respective methods. (Author) [pt

Initial Characterization of the Wave Resource at Several High Energy U.S. Sites

OpenAIRE

Dallman, Ann; Neary, Vincent S.

2014-01-01

Wave energy resource characterization efforts are critical for developing knowledge of the physical conditions experienced by wave energy converter (WEC) devices and arrays. Developers are lacking a consistent characterization of possible wave energy test sites, and therefore Sandia National Laboratories (SNL) has been tasked with developing a catalogue characterizing three high energy U.S. test sites. The initial results and framework for the catalogue are discussed in this paper. U.S. De...

Physical activity and 5-year changes in physical performance tests and bone mineral density in postmenopausal women: the Yokogoshi Study.

Science.gov (United States)

Kitamura, Kaori; Nakamura, Kazutoshi; Kobayashi, Ryosaku; Oshiki, Rieko; Saito, Toshiko; Oyama, Mari; Takahashi, Shunsuke; Nishiwaki, Tomoko; Iwasaki, Masanori; Yoshihara, Akihiro

2011-09-01

The effect of physical activity on musculoskeletal health in older adults is not completely understood. The aim of this study was to determine the relationship between physical activity and 5-year changes in physical performance tests and bone mineral density (BMD) in postmenopausal women. The design was a 5-year cohort study. Subjects were 507 women (55-74 years old) living in a rural community in Japan. Physical activity assessed included housework, farm work, and moderate leisure-time physical activity within the previous week. Measurements at baseline included handgrip strength, walking time (timed "Up & Go" test) and BMD of the femoral neck and vertebrae. Five-year changes in these measures (outcome variables) were compared among groups with different levels of physical activity by analysis of covariance. Women who did not do housework performed worse in changes in handgrip strength (difference=2.22 kg, P=0.0201) and worse in changes in the walking time (difference=0.54 s, P=0.0072) than those who did housework alone. Women who spent at least 9h per week (median=24) doing farm work performed better in changes in handgrip strength (difference=0.28 kg, P=0.0334), but worse in changes in the walking time (difference=0.66 s, Pwork. However, leisure-time activity was not associated with changes in any outcome variable, and none of the physical activities predicted BMD changes. Engaging in housework and farm work are determinants of physical function in postmenopausal women, which may help them maintain independence in daily living. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

Physical sampling for site and waste characterization

International Nuclear Information System (INIS)

Bonnough, T.L.

1996-01-01

Physical sampling plays a basic role in high-level radioactive waste management program effort. The term ''physical sampling'' used here means collecting tangible, physical samples of soil, water, air, waste streams, or other materials. The industry defines the term ''physical sampling'' broadly to include measurements of physical conditions such as temperature, wind conditions, and pH, which are also often taken in a sample collection effort. Most environmental compliance actions are supported by the results of taking, recording, and analyzing physical samples and the measurements of physical conditions taken in association with sample collecting. Therefore, the when and how to take samples is needed to be known and planned

Preliminary analyses for HTTR`s start-up physics tests by Monte Carlo code MVP

Energy Technology Data Exchange (ETDEWEB)

Nojiri, Naoki [Science and Technology Agency, Tokyo (Japan); Nakano, Masaaki; Ando, Hiroei; Fujimoto, Nozomu; Takeuchi, Mitsuo; Fujisaki, Shingo; Yamashita, Kiyonobu

1998-08-01

Analyses of start-up physics tests for High Temperature Engineering Test Reactor (HTTR) have been carried out by Monte Carlo code MVP based on continuous energy method. Heterogeneous core structures were modified precisely, such as the fuel compacts, fuel rods, coolant channels, burnable poisons, control rods, control rod insertion holes, reserved shutdown pellet insertion holes, gaps between graphite blocks, etc. Such precise modification of the core structures was difficult with diffusion calculation. From the analytical results, the followings were confirmed; The first criticality will be achieved around 16 fuel columns loaded. The reactivity at the first criticality can be controlled by only one control rod located at the center of the core with other fifteen control rods fully withdrawn. The excess reactivity, reactor shutdown margin and control rod criticality positions have been evaluated. These results were used for planning of the start-up physics tests. This report presents analyses of start-up physics tests for HTTR by MVP code. (author)

Physical startup tests for VVER-1200 of Novovoronezh NPP. Advanced technique and some results

Energy Technology Data Exchange (ETDEWEB)

Afanasiev, Dmitry A.; Kraynov, Yury A.; Pinegin, Anatoly A.; Tsyganov, Sergey V. [National Research Centre, Moscow (Russian Federation). Kurchatov Inst.

2017-09-15

The intention of the startup physics tests was to confirm design characteristics of the core loading and their compliance with safety analysis preconditions. The program of startup tests for the leading unit is usually composed in such a way that is is possible to study as much neutron-physical characteristics as possible in the safest condition of zero power. State-of-the-art safety analysis is including computer codes that use three dimensional neutron kinetics and thermohydraulics models. For the substantiation of such models, for its validation and verification there is a need in reactor experiments that implementing spatially distributed transients. We based on such statements when composing hot zero power physical startup program for the new VVER-1200 unit of Novovoronezh NPP. Several tests unconventional for VVER were developed for that program. It includes measuring the worth for each of control rod groups and measuring of single rod worth from the inserted groups - test that models rod ejection event in some sense.

FE-I4 pixel chip characterization with USBpix3 test system

Energy Technology Data Exchange (ETDEWEB)

Filimonov, Viacheslav; Gonella, Laura; Hemperek, Tomasz; Huegging, Fabian; Janssen, Jens; Krueger, Hans; Pohl, David-Leon; Wermes, Norbert [University of Bonn, Bonn (Germany)

2015-07-01

The USBpix readout system is a small and light weighting test system for the ATLAS pixel readout chips. It is widely used to operate and characterize FE-I4 pixel modules in lab and test beam environments. For multi-chip modules the resources on the Multi-IO board, that is the central control unit of the readout system, are coming to their limits, which makes the simultaneous readout of more than one chip at a time challenging. Therefore an upgrade of the current USBpix system has been developed. The upgraded system is called USBpix3 - the main focus of the talk. Characterization of single chip FE-I4 modules was performed with USBpix3 prototype (digital, analog, threshold and source scans; tuning). PyBAR (Bonn ATLAS Readout in Python scripting language) was used as readout software. PyBAR consists of FEI4 DAQ and Data Analysis Libraries in Python. The presentation describes the USBpix3 system, results of FE-I4 modules characterization and preparation for the multi-chip module and multi-module readout with USBpix3.

Benchmark physics tests in the metallic-fueled assembly ZPPR-15

International Nuclear Information System (INIS)

McFarlane, H.F.; Brumbach, S.B.; Carpenter, S.G.; Collins, P.J.

1989-01-01

Results of the first benchmark physics tests of a metallic-fueled, demonstration-size liquid-metal reactor (LMR) are reported. A simple, two-zone, cylindrical conventional assembly was built with three distinctly different compositions to represent the stages of the Integral Fast Reactor fuel cycle. Experiments included criticality, control, power distribution, reaction rate ratios, reactivity coefficients, shielding, kinetics, and spectrum. Analysis was done with three-dimensional nodal diffusion calculations and ENDF/B-V.2 cross sections. Predictions of the ZPPR-15 reactor physics parameters agreed sufficiently well with the measured values to justify confidence in design analyses for metallic-fueled LMRs

Benchmark physics tests in the metallic-fuelled assembly ZPPR-15

International Nuclear Information System (INIS)

McFarlane, H.F.; Brumbach, S.B.; Carpenter, S.G.; Collins, P.J.

1987-01-01

Results of the first benchmark physics tests of a metallic-fueled, demonstration-size, liquid metal reactor are reported. A simple, two-zone, cylindrical conventional assembly was built with three distinctly different compositions to represent the stages of the Integral Fast Reactor fuel cycle. Experiments included criticality, control, power distribution, reaction rate ratios, reactivity coefficients, shielding, kinetics and spectrum. Analysis was done with 3-D nodal diffusion calculations and ENDFIB-V.2 cross sections. Predictions of the ZPPR-15 reactor physics parameters agreed sufficiently well with the measured values to justify confidence in design analyses for metallic-fueled LMRs

Development and Testing of the Observational System for Recording Physical Activity in Children: Elementary School

Science.gov (United States)

McIver, Kerry L.; Brown, William H.; Pfeiffer, Karin A.; Dowda, Marsha; Pate, Russell R.

2016-01-01

Purpose: This study describes the development and pilot testing of the Observational System for Recording Physical Activity-Elementary School (OSRAC-E) Version. Method: This system was developed to observe and document the levels and types of physical activity and physical and social contexts of physical activity in elementary school students…

Installation and Characterization of Charged Particle Sources for Space Environmental Effects Testing

Science.gov (United States)

Skevington, Jennifer L.

2010-01-01

Charged particle sources are integral devices used by Marshall Space Flight Center s Environmental Effects Branch (EM50) in order to simulate space environments for accurate testing of materials and systems. By using these sources inside custom vacuum systems, materials can be tested to determine charging and discharging properties as well as resistance to sputter damage. This knowledge can enable scientists and engineers to choose proper materials that will not fail in harsh space environments. This paper combines the steps utilized to build a low energy electron gun (The "Skevington 3000") as well as the methods used to characterize the output of both the Skevington 3000 and a manufactured Xenon ion source. Such characterizations include beam flux, beam uniformity, and beam energy. Both sources were deemed suitable for simulating environments in future testing.

Standard test methods for characterizing duplex grain sizes

CERN Document Server

American Society for Testing and Materials. Philadelphia

2002-01-01

1.1 These test methods provide simple guidelines for deciding whether a duplex grain size exists. The test methods separate duplex grain sizes into one of two distinct classes, then into specific types within those classes, and provide systems for grain size characterization of each type. 1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard to consult appropriate safety and health practices and determine the applicability of regulatory limitations prior to its use.

Upgraded Features of Newly Constructed Fuel Assembly Mechanical Characterization Test Facility in KAERI

Energy Technology Data Exchange (ETDEWEB)

Lee, Kang Hee; Kang, Heung Seok; Yoon, Kyung Ho; Kim, Hyung Kyu; Lee, Young Ho; Kim, Soo Ho; Yang, Jae Ho [KAERI, Daejeon (Korea, Republic of)

2016-05-15

Fuel assembly mechanical characterization test facility (FAMeCT) in KAERI is newly constructed with upgraded functional features such as increased loading capacity, under-water vibration testing and severe earthquake simulation for extended fuel design guideline. The facility building is compactly designed in the scale of 3rd floor building and has regions for assembly-wise mechanical test equipment, dynamic load (seismic) simulating test system, small scale hydraulic loop and component wise test equipment. Figure 1 shows schematic regional layout of the facility building. Mechanical test platform and system is designed to increase loading capacity for axial compression test. Structural stability of the support system of new upper core plate simulator is validated through a limit case functional test. Fuel assembly mechanical characterization test facility in KAERI is newly constructed and upgraded with advanced functional features such as uprated loading capacity, under-water vibration testing and severe earthquake simulation for extended fuel design guideline. This paper briefly introduce the test facility construction and scope of the facility and is focused on the upgraded design features of the facility. Authors hope to facilitate the facility more in the future and collaborate with the industry.

Characterization of mixed CH-TRU waste for the WIPP Experimental Test Program conducted at ANL-W

International Nuclear Information System (INIS)

Dwight, C.C.; McClellan, G.C.; Guay, K.P.; Courtney, J.C.; Duff, M.J.

1992-01-01

Argonne National Laboratory is participating in the Department of Energy's Waste Isolation Pilot Plant (WIPP) Experimental Test Program by characterizing and repackaging mixed contact-handled transuranic waste. Characterization activities include gas sampling the waste containers, visually examining the waste contents, categorizing the contents according to their gas generation potentials, and weighing the contents. The waste is repackaged from 0.21m 3 (55 gallon) drums into instrumented steel test bins which can hold up to six drum-equivalents in volume. Eventually the loaded test bins will be shipped to WIPP where they will be evaluated during a five-year test program. Three test bins of inorganic solids (primarily glass) were prepared between March and September 1991 and are ready for shipment to WIPP. The characterization activities confirmed process knowledge of the waste and verified the nondestructive examinations; the gas sample analyses showed the target constituents to be within allowable regulatory limits. A new waste characterization chamber is being developed at ANL-W which will improve worker safety, decrease the potential for contamination spread, and increase the waste characterization throughput. The new facility is expected to begin operations by Fall 1992. A comprehensive summary of the project is contained herein

Physical-mechanical and anatomical characterization in 26-year-old Eucalyptus resinifera wood

OpenAIRE

Lima,Israel Luiz de; Longui,Eduardo Luiz; Freitas,Miguel Luiz Menezes; Zanatto,Antonio Carlos Scatena; Zanata,Marcelo; Florsheim,Sandra Monteiro Borges; Bortoletto Jr.,Geraldo

2014-01-01

In the present study, we aimed to characterize Eucalyptus resinifera wood through physical and mechanical assays and wood anatomy studies, as well as determine the relationships between the properties and anatomy of wood. We used samples collected from the area close to the bark of ten 26-year-old E. resinifera trees. We concluded that the specific gravity (Gb), compression (f c0), and shear parallel to grain (f v0) were ranked in strength classes C30, C40 and C60, respectively, and that volu...

Characterization and BMP Tests of Liquid Substrates for High-rate Anaerobic Digestion

Directory of Open Access Journals (Sweden)

M. Mainardis

2018-01-01

Full Text Available This work was focused on the physicochemical characterization and biochemical methane potential (BMP tests of some liquid organic substrates, to verify if they were suitable for undergoing a process of high-velocity anaerobic digestion. The selected substrates were: first and second cheese whey, organic fraction of municipal solid waste (OFMSW leachate, condensate water and slaughterhouse liquid waste. Firstly, a physicochemical characterization was performed, using traditional and macromolecular parameters; then, batch anaerobic tests were carried out, and some continuous tests were planned. The results revealed that all the analyzed substrates have a potential to be anaerobically treated. Valuable information about treatment rate for a high-velocity anaerobic digestion process was obtained. Start-up of a lab-scale UASB reactor, treating diluted cheese whey, was successfully achieved with good COD removal efficiency. These preliminary results are expected to be further investigated in a successive phase, where continuous tests will be conducted on condensate water and OFMSW leachate.

An Empirical Analysis of the Physical Aptitude Exam as a Predictor of Performance on the Physical Readiness Test

National Research Council Canada - National Science Library

Patrick, Robert

2000-01-01

... shuttle run, a standing longiump, and a kneeling basketball throw. The Physical Readiness Test, administered semi-annually to all naval personnel including midshipmen, consists of modified situps, pushups, and a 1.5-mile run...

Testing the standard model of particle physics using lattice QCD

International Nuclear Information System (INIS)

Water, Ruth S van de

2007-01-01

Recent advances in both computers and algorithms now allow realistic calculations of Quantum Chromodynamics (QCD) interactions using the numerical technique of lattice QCD. The methods used in so-called '2+1 flavor' lattice calculations have been verified both by post-dictions of quantities that were already experimentally well-known and by predictions that occurred before the relevant experimental determinations were sufficiently precise. This suggests that the sources of systematic error in lattice calculations are under control, and that lattice QCD can now be reliably used to calculate those weak matrix elements that cannot be measured experimentally but are necessary to interpret the results of many high-energy physics experiments. These same calculations also allow stringent tests of the Standard Model of particle physics, and may therefore lead to the discovery of new physics in the future

Examine the Relationship between Dynamic Balance and Physical Fitness Tests in Preschool Children

OpenAIRE

杉浦, 宏季; Sugiura, Hiroki; 杉本, 寛恵; Sugimoto, Hiroe

2016-01-01

This study examined the relationship between dynamic balance tests and various physical fitness tests in preschool children. The subjects were 22 preschool children (age, 5.0+0.4years; height, 107.3+5.7cm; weight, 17.9+3.4 kg). Dynamic balance was assessed by walking the length of a balance beam several times (beam height, 30cm; width, 10cm; length, 200cm) and walking a pathway (width, 10cm; length, 200cm). Physical fitness was assessed with activities such as a 25-meter run, continuous bilat...

Quantitative tests of pion physics in simple nuclear systems

International Nuclear Information System (INIS)

Ericson, T.E.O.

1984-01-01

The need for quantitative tests of pion physics in simple nuclear systems is discussed under eight topic headings. These include: one-pion exchange potential, p-wave NN scattering lengths, opep pole in forward NN dispersion relations, np → pn near the forward direction, pionic interactions, deuteron D/S ratio eta, deuteron quadrupole moment, and finally the joint case of eta and Q. (U.K.)

Anticipated simulation of Angra-1 start-up physical tests

International Nuclear Information System (INIS)

Fernandes, V.B.; Perrotta, J.A.; Silva Ipojuca, T. da; Ponzoni Filho, P.

1981-01-01

Some results foreseen by the Department of Nuclear Fuel (DCN. O) in Furnas for the measurements that will be realized during the start-up integrated tests for Angra-1 are presented. All the forecasting is based on a DCN.O proper correlation methodology, developed from basic physical principles, using computer codes developed by the authors or public computer codes adapted to this methodology. (E.G.) [pt

[Alusti test: New scale for assessment of physical performance in the geriatric population].

Science.gov (United States)

Calvo Aguirrey, Juan José; Alustiza Navarro, Josu; Uranga Zaldúa, Joana; Sarasqueta Eizaguirre, Cristina; Bueno Yáñez, Olga

2018-06-11

Physical and psychological functional conditions are key factors in the elderly population. Many evaluation tools are available, but they cannot be applied to the whole geriatric population. The use Alusti Test is presented. This test consists of 2versions, which enable it to encompass this wide and complex population spectrum. A prospective study with the institutionalised, hospitalised, and community population, was conducted between September and December 2016. A comparative analysis was conducted using the Barthel Index (BI), Gait Speed Test (GST), Timed «Up & Go» Test (TUG), Short Physical Performance Battery (SPPB), and Tinetti Test. A total of 363 subjects were enrolled (mean age: 83.25 years), with varying levels of functional and cognitive conditions. The test was simple and quick to apply (3-6min), 100% applicable and usable with broad floor and ceiling effects (0-100 points) with an intraclass correlation coefficient (ICC) that shows a high inter-observer reliability (ICC = 0.99), and a good correlation in its full version with BI (ICC = 0.86) (95% CI: 0.82-0.88), and the Tinetti test (ICC = 0.76; 95% CI: 0.71-0.81), as well as in the abbreviated version BI (ICC = 0.71; 95% CI: 0.65-0.75) and Tinetti Test (ICC = 0.90; 95% CI: 0.88-0.92). This allows the variation of the functional condition to be measured, which in our sample showed an increase of 10.9%, after a period of hospital admission. It is considered that Alusti test meets the requirements for physical performance assessment in the whole the geriatric population. The highest level of accuracy is given by the Tinetti test, which has greater applicability. Copyright © 2018 SEGG. Publicado por Elsevier España, S.L.U. All rights reserved.

A job-related fitness test for the Dutch police

NARCIS (Netherlands)

Strating, M.; Bakker, R. H.; Dijkstra, G. J.; Lemmink, K. A. P. M.; Groothoff, J. W.

Background The variety of tasks that characterize police work highlights the importance of being in good physical condition. Aims To take a first step at standardizing the administration of a job-related test to assess a person's ability to perform the physical demands of the core tasks of police

Radiological, physical, and chemical characterization of low-level alpha contaminated wastes stored at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Apel, M.L.; Becker, G.K.; Ragan, Z.K.; Frasure, J.; Raivo, B.D.; Gale, L.G.; Pace, D.P.

1994-03-01

This document provides radiological, physical, and chemical characterization data for low-level alpha-contaminated radioactive and low-level alpha-contaminated radioactive and hazardous (i.e., mixed) wastes stored at the Idaho National Engineering Laboratory and considered for treatment under the Private Sector Participation Initiative Program. Waste characterization data are provided in the form of INEL Waste Profile Sheets. These documents provide, for each content code, information on waste identification, waste description, waste storage configuration, physical/chemical waste composition, radionuclide and associated alpha activity waste characterization data, and hazardous constituents present in the waste. Information is provided for 97 waste streams which represent an estimated total volume of 25,450 m 3 corresponding to a total mass of approximately 12,000,000 kg. In addition, considerable information concerning alpha, beta, gamma, and neutron source term data specific to Rocky Flats-generated waste forms stored at the INEL are provided to assist in facility design specification

Radiological, physical, and chemical characterization of low-level alpha contaminated wastes stored at the Idaho National Engineering Laboratory

Energy Technology Data Exchange (ETDEWEB)

Apel, M.L.; Becker, G.K.; Ragan, Z.K.; Frasure, J.; Raivo, B.D.; Gale, L.G.; Pace, D.P.

1994-03-01

This document provides radiological, physical, and chemical characterization data for low-level alpha-contaminated radioactive and low-level alpha-contaminated radioactive and hazardous (i.e., mixed) wastes stored at the Idaho National Engineering Laboratory and considered for treatment under the Private Sector Participation Initiative Program. Waste characterization data are provided in the form of INEL Waste Profile Sheets. These documents provide, for each content code, information on waste identification, waste description, waste storage configuration, physical/chemical waste composition, radionuclide and associated alpha activity waste characterization data, and hazardous constituents present in the waste. Information is provided for 97 waste streams which represent an estimated total volume of 25,450 m 3 corresponding to a total mass of approximately 12,000,000 kg. In addition, considerable information concerning alpha, beta, gamma, and neutron source term data specific to Rocky Flats-generated waste forms stored at the INEL are provided to assist in facility design specification.

Classroom Tests and Achievement in Problem Solving in Physical Geography

Science.gov (United States)

Monk, Janice J.; Stallings, William M.

1975-01-01

Two hundred students in an undergraduate physical geography course were assigned to a group which received either factually oriented quizzes or quizzes which stressed higher level behaviors such as application and analysis. Evaluation of the results indicated that the variation in testing procedures had no discernable effect on student scores in…

Standardization of waste acceptance test methods by the Materials Characterization Center

International Nuclear Information System (INIS)

Slate, S.C.

1985-01-01

This paper describes the role of standardized test methods in demonstrating the acceptability of high-level waste (HLW) forms for disposal. Key waste acceptance tests are standardized by the Materials Characterization Center (MCC), which the US Department of Energy (DOE) has established as the central agency in the United States for the standardization of test methods for nuclear waste materials. This paper describes the basic three-step process that is used to show that waste is acceptable for disposal and discusses how standardized tests are used in this process. Several of the key test methods and their areas of application are described. Finally, future plans are discussed for using standardized tests to show waste acceptance. 9 refs., 1 tab

Work-related measures of physical and behavioral health function: Test-retest reliability.

Science.gov (United States)

Marino, Molly Elizabeth; Meterko, Mark; Marfeo, Elizabeth E; McDonough, Christine M; Jette, Alan M; Ni, Pengsheng; Bogusz, Kara; Rasch, Elizabeth K; Brandt, Diane E; Chan, Leighton

2015-10-01

The Work Disability Functional Assessment Battery (WD-FAB), developed for potential use by the US Social Security Administration to assess work-related function, currently consists of five multi-item scales assessing physical function and four multi-item scales assessing behavioral health function; the WD-FAB scales are administered as Computerized Adaptive Tests (CATs). The goal of this study was to evaluate the test-retest reliability of the WD-FAB Physical Function and Behavioral Health CATs. We administered the WD-FAB scales twice, 7-10 days apart, to a sample of 376 working age adults and 316 adults with work-disability. Intraclass correlation coefficients were calculated to measure the consistency of the scores between the two administrations. Standard error of measurement (SEM) and minimal detectable change (MDC90) were also calculated to measure the scales precision and sensitivity. For the Physical Function CAT scales, the ICCs ranged from 0.76 to 0.89 in the working age adult sample, and 0.77-0.86 in the sample of adults with work-disability. ICCs for the Behavioral Health CAT scales ranged from 0.66 to 0.70 in the working age adult sample, and 0.77-0.80 in the adults with work-disability. The SEM ranged from 3.25 to 4.55 for the Physical Function scales and 5.27-6.97 for the Behavioral Health function scales. For all scales in both samples, the MDC90 ranged from 7.58 to 16.27. Both the Physical Function and Behavioral Health CATs of the WD-FAB demonstrated good test-retest reliability in adults with work-disability and general adult samples, a critical requirement for assessing work related functioning in disability applicants and in other contexts. Copyright © 2015 Elsevier Inc. All rights reserved.

Factors that encourage females to pursue physical science careers: Testing five common hypotheses

Science.gov (United States)

Hazari, Zahra; Potvin, Geoff; Lock, Robynne M.; Lung, Florin; Sadler, Philip M.; Sonnert, Gerhard

2012-03-01

There are many hypotheses regarding factors that may encourage female students to pursue careers in the physical sciences. Using Propensity Score Matching (PSM) on national data (n=7505) drawn from the Persistence Research in Science and Engineering (PRiSE) project, we test five commonly held beliefs including having a single-sex physics class, having a female physics teacher, having female scientist guest speakers in physics class, discussing the work of women scientists in physics class, and discussing the under-representation of women in physics class. The effect of these experiences is compared for female students who are matched on several factors, including parental education, prior science/math interests, and academic background, thereby controlling for the effect of many confounding variables.

Determinants of physical activity among people with spinal cord injury: a test of social cognitive theory.

Science.gov (United States)

Ginis, Kathleen A Martin; Latimer, Amy E; Arbour-Nicitopoulos, Kelly P; Bassett, Rebecca L; Wolfe, Dalton L; Hanna, Steven E

2011-08-01

Little theory-based research has focused on understanding and increasing physical activity among people with physical disabilities. Testing a social cognitive theory-based model of determinants is important for identifying variables to target in physical activity-enhancing interventions. The aim of this study is to examine Social Cognitive Theory variables as predictors of physical activity among people living with spinal cord injury. Structural equation modeling was used to test a model of Social Cognitive Theory predictors of physical activity (n=160). The model explained 39% of the variance in physical activity. Self-regulation was the only significant, direct predictor. Self-regulatory efficacy and outcome expectations had indirect effects, mediated by self-regulation. Social Cognitive Theory is useful for predicting physical activity in people with spinal cord injury. Self-regulation is the most potent Social Cognitive Theory predictor of physical activity in people with spinal cord injury. Self-regulation and its determinants should be targeted in physical activity-enhancing interventions.

Physical and Mechanical Characterization of Sugarcane Bagasse Particleboards for Civil Construction

Directory of Open Access Journals (Sweden)

Rosane Battistelle

2016-12-01

Full Text Available In the worldwide market of particleboard production, the use of alternative raw materials is increasing, due to high demand and lack of traditional raw material, despite efforts of reforestation. In Brazil, the main agricultural commodity is sugarcane due to the copious production of sugar and ethanol. In the state of São Paulo alone approximately 140 million tons of sugarcane bagasse are produced every year, from which around 70% is burned for energy production, not adding value to the residue and generating pollution to the environment; and the other 30% is sold for composting. The objective of this work is to add value to the sugarcane bagasse by using it as a raw material for particleboard production to be employed as flooring in the area of civil construction. To achieve this, the present research characterized the physical and mechanical characteristics of the particleboards with the following alternative raw materials: sugarcane bagasse and leaves of bamboo. Particleboards were produced to reach high density (0.8g/cm3 using the resin (bi-component polyurethane castor oil. Tests for abrasion, roughness and resistance to denting and wear (Janka hardness verified that the addition of leaves of bamboo in the mixtures, contrary to what was expected, did not confer a greater degree of resistance to the particleboards. Lastly, the results showed that sugarcane bagasse is a viable raw material alternative for the production of particleboards, intended to be used as products and flooring.

CHEMICAL AND PHYSICAL CHARACTERIZATION OF COLLAPSING LOW-MASS PRESTELLAR DENSE CORES

Energy Technology Data Exchange (ETDEWEB)

Hincelin, U. [Department of Chemistry, University of Virginia, Charlottesville, VA 22904 (United States); Commerçon, B. [Ecole Normale Supérieure de Lyon, CRAL, UMR 5574 du CNRS, Université Lyon I, 46 Allée d’Italie, F-69364 Lyon cedex 07 (France); Wakelam, V.; Hersant, F.; Guilloteau, S. [Univ. Bordeaux, LAB, UMR 5804, F-33270, Floirac (France); Herbst, E., E-mail: ugo.hincelin@gmail.com [Departments of Chemistry and Astronomy, University of Virginia, Charlottesville, VA 22904 (United States)

2016-05-01

The first hydrostatic core, also called the first Larson core, is one of the first steps in low-mass star formation as predicted by theory. With recent and future high-performance telescopes, the details of these first phases are becoming accessible, and observations may confirm theory and even present new challenges for theoreticians. In this context, from a theoretical point of view, we study the chemical and physical evolution of the collapse of prestellar cores until the formation of the first Larson core, in order to better characterize this early phase in the star formation process. We couple a state-of-the-art hydrodynamical model with full gas-grain chemistry, using different assumptions for the magnetic field strength and orientation. We extract the different components of each collapsing core (i.e., the central core, the outflow, the disk, the pseudodisk, and the envelope) to highlight their specific physical and chemical characteristics. Each component often presents a specific physical history, as well as a specific chemical evolution. From some species, the components can clearly be differentiated. The different core models can also be chemically differentiated. Our simulation suggests that some chemical species act as tracers of the different components of a collapsing prestellar dense core, and as tracers of the magnetic field characteristics of the core. From this result, we pinpoint promising key chemical species to be observed.

Advanced ceramic composite for high energy resistors. Characterization of electrical and physical properties

International Nuclear Information System (INIS)

Farrokh, Fattahi; Navid, Tagizadegan; Naser, Tabatabaei; Ahmad, Rashtehizadeh

2005-01-01

There is a need to characterize and apply advanced materials to improve the performance of components used in pulse power systems. One area of innovation is the use of bulk electrically conductive ceramics for non-inductive, high energy and high power electrical resistors. Standard Ceramics Inc. has developed a unique silicon carbide structural ceramic composite which exhibits electrical conductivity. The new conductive bulk ceramic material has a controlled microstructure, which results in improved homogeneity, making the material suitable for use as a non-inductive high energy resistor. This paper describes characterization of the material's physical and electrical properties and relates them to improvements in low-inductance, high temperature, high power density and high energy density resistors. The bulk resistor approach offers high reliability through better mechanical properties and simplicity of construction

High heat flux testing of CFC composites for the tokamak physics experiment

Science.gov (United States)

Valentine, P. G.; Nygren, R. E.; Burns, R. W.; Rocket, P. D.; Colleraine, A. P.; Lederich, R. J.; Bradley, J. T.

1996-10-01

High heat flux (HHF) testing of carbon fiber reinforced carbon composites (CFC's) was conducted under the General Atomics program to develop plasma-facing components (PFC's) for Princeton Plasma Physics Laboratory's tokamak physics experiment (TPX). As part of the process of selecting TPX CFC materials, a series of HHF tests were conducted with the 30 kW electron beam test system (EBTS) facility at Sandia National Laboratories, and with the plasma disruption simulator I (PLADIS-I) facility at the University of New Mexico. The purpose of the tests was to make assessments of the thermal performance and erosion behavior of CFC materials. Tests were conducted with 42 different CFC materials. In general, the CFC materials withstood the rapid thermal pulse environments without fracturing, delaminating, or degrading in a non-uniform manner; significant differences in thermal performance, erosion behavior, vapor evolution, etc. were observed and preliminary findings are presented below. The CFC's exposed to the hydrogen plasma pulses in PLADIS-I exhibited greater erosion rates than the CFC materials exposed to the electron-beam pulses in EBTS. The results obtained support the continued consideration of a variety of CFC composites for TPX PFC components.

Testing a self-determination theory model of children’s physical activity motivation: a cross-sectional study

Science.gov (United States)

2013-01-01

Background Understanding children’s physical activity motivation, its antecedents and associations with behavior is important and can be advanced by using self-determination theory. However, research among youth is largely restricted to adolescents and studies of motivation within certain contexts (e.g., physical education). There are no measures of self-determination theory constructs (physical activity motivation or psychological need satisfaction) for use among children and no previous studies have tested a self-determination theory-based model of children’s physical activity motivation. The purpose of this study was to test the reliability and validity of scores derived from scales adapted to measure self-determination theory constructs among children and test a motivational model predicting accelerometer-derived physical activity. Methods Cross-sectional data from 462 children aged 7 to 11 years from 20 primary schools in Bristol, UK were analysed. Confirmatory factor analysis was used to examine the construct validity of adapted behavioral regulation and psychological need satisfaction scales. Structural equation modelling was used to test cross-sectional associations between psychological need satisfaction, motivation types and physical activity assessed by accelerometer. Results The construct validity and reliability of the motivation and psychological need satisfaction measures were supported. Structural equation modelling provided evidence for a motivational model in which psychological need satisfaction was positively associated with intrinsic and identified motivation types and intrinsic motivation was positively associated with children’s minutes in moderate-to-vigorous physical activity. Conclusions The study provides evidence for the psychometric properties of measures of motivation aligned with self-determination theory among children. Children’s motivation that is based on enjoyment and inherent satisfaction of physical activity is

Comparison of physically based constitutive models characterizing armor steel over wide temperature and strain rate ranges

International Nuclear Information System (INIS)

Xu, Zejian; Huang, Fenglei

2012-01-01

Both descriptive and predictive capabilities of five physically based constitutive models (PB, NNL, ZA, VA, and RK) are investigated and compared systematically, in characterizing plastic behavior of the 603 steel at temperatures ranging from 288 to 873 K, and strain rates ranging from 0.001 to 4500 s −1 . Determination of the constitutive parameters is introduced in detail for each model. Validities of the established models are checked by strain rate jump tests performed under different loading conditions. The results show that the RK and NNL models have better performance in the description of material behavior, especially the work-hardening effect, while the PB and VA models predict better. The inconsistency that is observed between the capabilities of description and prediction of the models indicates the existence of the minimum number of required fitting data, reflecting the degree of a model's requirement for basic data in parameter calibration. It is also found that the description capability of a model is dependent to a large extent on both its form and the number of its constitutive parameters, while the precision of prediction relies largely on the performance of description. In the selection of constitutive models, the experimental data and the constitutive models should be considered synthetically to obtain a better efficiency in material behavior characterization

Characterization of mixed CH-TRU waste for the WIPP Experimental Test Program conducted at ANL-W

Energy Technology Data Exchange (ETDEWEB)

Dwight, C.C.; McClellan, G.C.; Guay, K.P. [Argonne National Lab., Idaho Falls, ID (United States); Courtney, J.C. [Louisiana State Univ., Baton Rouge, LA (United States); Duff, M.J. [Consolidated Technical Services, Inc., Walkersville, MD (United States)

1992-02-01

Argonne National Laboratory is participating in the Department of Energy`s Waste Isolation Pilot Plant (WIPP) Experimental Test Program by characterizing and repackaging mixed contact-handled transuranic waste. Characterization activities include gas sampling the waste containers, visually examining the waste contents, categorizing the contents according to their gas generation potentials, and weighing the contents. The waste is repackaged from 0.21m{sup 3} (55 gallon) drums into instrumented steel test bins which can hold up to six drum-equivalents in volume. Eventually the loaded test bins will be shipped to WIPP where they will be evaluated during a five-year test program. Three test bins of inorganic solids (primarily glass) were prepared between March and September 1991 and are ready for shipment to WIPP. The characterization activities confirmed process knowledge of the waste and verified the nondestructive examinations; the gas sample analyses showed the target constituents to be within allowable regulatory limits. A new waste characterization chamber is being developed at ANL-W which will improve worker safety, decrease the potential for contamination spread, and increase the waste characterization throughput. The new facility is expected to begin operations by Fall 1992. A comprehensive summary of the project is contained herein.

Characterization of mixed CH-TRU waste for the WIPP Experimental Test Program conducted at ANL-W

Energy Technology Data Exchange (ETDEWEB)

Dwight, C.C.; McClellan, G.C.; Guay, K.P. (Argonne National Lab., Idaho Falls, ID (United States)); Courtney, J.C. (Louisiana State Univ., Baton Rouge, LA (United States)); Duff, M.J. (Consolidated Technical Services, Inc., Walkersville, MD (United States))

1992-01-01

Argonne National Laboratory is participating in the Department of Energy's Waste Isolation Pilot Plant (WIPP) Experimental Test Program by characterizing and repackaging mixed contact-handled transuranic waste. Characterization activities include gas sampling the waste containers, visually examining the waste contents, categorizing the contents according to their gas generation potentials, and weighing the contents. The waste is repackaged from 0.21m{sup 3} (55 gallon) drums into instrumented steel test bins which can hold up to six drum-equivalents in volume. Eventually the loaded test bins will be shipped to WIPP where they will be evaluated during a five-year test program. Three test bins of inorganic solids (primarily glass) were prepared between March and September 1991 and are ready for shipment to WIPP. The characterization activities confirmed process knowledge of the waste and verified the nondestructive examinations; the gas sample analyses showed the target constituents to be within allowable regulatory limits. A new waste characterization chamber is being developed at ANL-W which will improve worker safety, decrease the potential for contamination spread, and increase the waste characterization throughput. The new facility is expected to begin operations by Fall 1992. A comprehensive summary of the project is contained herein.

An evaluation of slug interference tests for aquifer characterization at the Hanford Site

International Nuclear Information System (INIS)

Spane, F.A. Jr.; Thorne, P.D.

1992-01-01

Slug interference tests are conducted by instantaneously changing the water level in a well and monitoring the aquifer response at one or more observation wells. The applicability of this method for hydraulic characterization of a high permeability unconfined aquifer at the Hanford Site was evaluated. Analytical techniques were used to predict slug interference responses over a range of aquifer hydraulic conditions and observation well distances. This was followed by a field test of the proposed technique. The results showed that slug interference testing can be used to characterize aquifers having transmissivities up to 10 -1 m 2 /s compared to a maximum transmissivity of about 10 -3 m 2 /s for single-well slug tests. The amplitude of the pressure response measured at the observation well is primarily determined by aquifer storativity, while the time-lag of the pressure peak is mainly controlled by the transmissivity. Several recommendations are made optimizing the results of slug interference tests in higher permeability, unconfined to semiconfined aquifers

Early universe cosmology and tests of fundamental physics

International Nuclear Information System (INIS)

Albrecht, Andreas; Frieman, Joshua A.; Trodden, Mark

2002-01-01

This is the report of the Working Group on Early Universe Cosmology and tests of Fundamental Physics, group P4.8 of the of the Snowmass 2001 conference. Here we summarize the impressive array of advances that have taken place in this field, and identify opportunities for even greater progress in the future. Topics include Dark Energy, Cosmic Acceleration, Inflation, Phase Transitions, Baryogenesis, and String/M-theory Cosmology. The introductory section gives an executive summary with six key open questions on which we can expect to make significant progress

Evaluation of the theory-based Quality Improvement in Physical Therapy (QUIP) programme: a one-group, pre-test post-test pilot study.

Science.gov (United States)

Rutten, Geert M; Harting, Janneke; Bartholomew, L Kay; Schlief, Angelique; Oostendorp, Rob A B; de Vries, Nanne K

2013-05-25

Guideline adherence in physical therapy is far from optimal, which has consequences for the effectiveness and efficiency of physical therapy care. Programmes to enhance guideline adherence have, so far, been relatively ineffective. We systematically developed a theory-based Quality Improvement in Physical Therapy (QUIP) programme aimed at the individual performance level (practicing physiotherapists; PTs) and the practice organization level (practice quality manager; PQM). The aim of the study was to pilot test the multilevel QUIP programme's effectiveness and the fidelity, acceptability and feasibility of its implementation. A one-group, pre-test, post-test pilot study (N = 8 practices; N = 32 PTs, 8 of whom were also PQMs) done between September and December 2009. Guideline adherence was measured using clinical vignettes that addressed 12 quality indicators reflecting the guidelines' main recommendations. Determinants of adherence were measured using quantitative methods (questionnaires). Delivery of the programme and management changes were assessed using qualitative methods (observations, group interviews, and document analyses). Changes in adherence and determinants were tested in the paired samples T-tests and expressed in effect sizes (Cohen's d). Overall adherence did not change (3.1%; p = .138). Adherence to three quality indicators improved (8%, 24%, 43%; .000 ≤ p ≤ .023). Adherence to one quality indicator decreased (-15.7%; p = .004). Scores on various determinants of individual performance improved and favourable changes at practice organizational level were observed. Improvements were associated with the programme's multilevel approach, collective goal setting, and the application of self-regulation; unfavourable findings with programme deficits. The one-group pre-test post-test design limits the internal validity of the study, the self-selected sample its external validity. The QUIP programme has the potential to change physical

Cognitive and Physical Fatigue Tasks Enhance Pain, Cognitive Fatigue and Physical Fatigue in People with Fibromyalgia

Science.gov (United States)

Dailey, Dana L; Keffala, Valerie J; Sluka, Kathleen A

2014-01-01

Objective Fibromyalgia is a condition characterized by chronic widespread muscle pain and fatigue. The primary objective of this study was to determine if pain, perceived cognitive fatigue, and perceived physical fatigue were enhanced in participants with fibromyalgia compared to healthy controls during a cognitive fatigue task, a physical fatigue task and a dual fatigue task. Methods Twenty four people with fibromyalgia and 33 healthy controls completed pain, fatigue and function measures. A cognitive fatigue task (Controlled Oral Word Association Test) and physical fatigue task (Valpar peg test) were done individually and combined for a dual fatigue task. Resting pain, perceived cognitive fatigue and perceived physical fatigue were assessed during each task using visual analogue scales. Function was assessed with shoulder range of motion and grip. Results People with fibromyalgia had significantly higher increases in pain, cognitive fatigue and physical fatigue when compared to healthy controls after completion of a cognitive fatigue task, a physical fatigue task, or a dual fatigue task (pfatigue tasks, respectively. Conclusions These data show that people with fibromyalgia show larger increases in pain, perceived cognitive fatigue and perceived physical fatigue to both cognitive and physical fatigue tasks compared to healthy controls. The increases in pain and fatigue during cognitive and physical fatigue tasks could influence subject participation in daily activities and rehabilitation. PMID:25074583

Applying a probabilistic seismic-petrophysical inversion and two different rock-physics models for reservoir characterization in offshore Nile Delta

Science.gov (United States)

Aleardi, Mattia

2018-01-01

We apply a two-step probabilistic seismic-petrophysical inversion for the characterization of a clastic, gas-saturated, reservoir located in offshore Nile Delta. In particular, we discuss and compare the results obtained when two different rock-physics models (RPMs) are employed in the inversion. The first RPM is an empirical, linear model directly derived from the available well log data by means of an optimization procedure. The second RPM is a theoretical, non-linear model based on the Hertz-Mindlin contact theory. The first step of the inversion procedure is a Bayesian linearized amplitude versus angle (AVA) inversion in which the elastic properties, and the associated uncertainties, are inferred from pre-stack seismic data. The estimated elastic properties constitute the input to the second step that is a probabilistic petrophysical inversion in which we account for the noise contaminating the recorded seismic data and the uncertainties affecting both the derived rock-physics models and the estimated elastic parameters. In particular, a Gaussian mixture a-priori distribution is used to properly take into account the facies-dependent behavior of petrophysical properties, related to the different fluid and rock properties of the different litho-fluid classes. In the synthetic and in the field data tests, the very minor differences between the results obtained by employing the two RPMs, and the good match between the estimated properties and well log information, confirm the applicability of the inversion approach and the suitability of the two different RPMs for reservoir characterization in the investigated area.

Wave Resource Characterization at US Wave Energy Converter (WEC) Test Sites

Science.gov (United States)

Dallman, A.; Neary, V. S.

2016-02-01

The US Department of Energy's (DOE) Marine and Hydrokinetic energy (MHK) Program is supporting a diverse research and development portfolio intended to accelerate commercialization of the marine renewable industry by improving technology performance, reducing market barriers, and lowering the cost of energy. Wave resource characterization at potential and existing wave energy converter (WEC) test sites and deployment locations contributes to this DOE goal by providing a catalogue of wave energy resource characteristics, met-ocean data, and site infrastructure information, developed utilizing a consistent methodology. The purpose of the catalogue is to enable the comparison of resource characteristics among sites to facilitate the selection of test sites that are most suitable for a developer's device and that best meet their testing needs and objectives. It also provides inputs for the design of WEC test devices and planning WEC tests, including the planning of deployment and operations and maintenance. The first edition included three sites: the Pacific Marine Energy Center (PMEC) North Energy Test Site (NETS) offshore of Newport, Oregon, the Kaneohe Bay Naval Wave Energy Test Site (WETS) offshore of Oahu, HI, and a potential site offshore of Humboldt Bay, CA (Eureka, CA). The second edition was recently finished, which includes five additional sites: the Jennette's Pier Wave Energy Converter Test Site in North Carolina, the US Army Corps of Engineers (USACE) Field Research Facility (FRF), the PMEC Lake Washington site, the proposed PMEC South Energy Test Site (SETS), and the proposed CalWave Central Coast WEC Test Site. The operational sea states are included according to the IEC Technical Specification on wave energy resource assessment and characterization, with additional information on extreme sea states, weather windows, and representative spectra. The methodology and a summary of results will be discussed.

Diagnostic Accuracy of 3 Physical Examination Tests in the Assessment of Hip Microinstability.

Science.gov (United States)

Hoppe, Daniel J; Truntzer, Jeremy N; Shapiro, Lauren M; Abrams, Geoffrey D; Safran, Marc R

2017-11-01

Hip microinstability is a diagnosis gaining increasing interest. Physical examination tests to identify microinstability have not been objectively investigated using intraoperative confirmation of instability as a reference standard. To determine the test characteristics and diagnostic accuracy of 3 physical examination maneuvers in the detection of hip microinstability. Cohort study (diagnosis); Level of evidence, 2. A review was conducted of 194 consecutive hip arthroscopic procedures performed by a sports medicine surgeon at a tertiary-care academic center. Physical examination findings of interest, including the abduction-hyperextension-external rotation (AB-HEER) test, the prone instability test, and the hyperextension-external rotation (HEER) test, were obtained from prospectively collected data. The reference standard was intraoperative identification of instability based on previously published objective criteria. Test characteristics, including sensitivity, specificity, positive and negative predictive values, and accuracy, were calculated for each test as well as for combinations of tests. A total of 109 patients were included in the analysis. The AB-HEER test was most accurate, with a sensitivity of 80.6% (95% CI, 70.8%-90.5%) and a specificity of 89.4% (95% CI, 80.5%-98.2%). The prone instability test had a low sensitivity (33.9%) but a very high specificity (97.9%). The HEER test performed second in both sensitivity (71.0%) and specificity (85.1%). The combination of multiple tests with positive findings did not yield significantly greater accuracy. All tests had high positive predictive values (range, 86.3%-95.5%) and moderate negative predictive values (range, 52.9%-77.8%). When all 3 tests had positive findings, there was a 95.0% (95% CI, 90.1%-99.9%) chance that the patient had microinstability. The AB-HEER test most accurately predicted hip instability, followed by the HEER test and the prone instability test. However, the high specificity of the

Reliability of physical examination tests for the diagnosis of knee disorders: Evidence from a systematic review.

Science.gov (United States)

Décary, Simon; Ouellet, Philippe; Vendittoli, Pascal-André; Desmeules, François

2016-12-01

Clinicians often rely on physical examination tests to guide them in the diagnostic process of knee disorders. However, reliability of these tests is often overlooked and may influence the consistency of results and overall diagnostic validity. Therefore, the objective of this study was to systematically review evidence on the reliability of physical examination tests for the diagnosis of knee disorders. A structured literature search was conducted in databases up to January 2016. Included studies needed to report reliability measures of at least one physical test for any knee disorder. Methodological quality was evaluated using the QAREL checklist. A qualitative synthesis of the evidence was performed. Thirty-three studies were included with a mean QAREL score of 5.5 ± 0.5. Based on low to moderate quality evidence, the Thessaly test for meniscal injuries reached moderate inter-rater reliability (k = 0.54). Based on moderate to excellent quality evidence, the Lachman for anterior cruciate ligament injuries reached moderate to excellent inter-rater reliability (k = 0.42 to 0.81). Based on low to moderate quality evidence, the Tibiofemoral Crepitus, Joint Line and Patellofemoral Pain/Tenderness, Bony Enlargement and Joint Pain on Movement tests for knee osteoarthritis reached fair to excellent inter-rater reliability (k = 0.29 to 0.93). Based on low to moderate quality evidence, the Lateral Glide, Lateral Tilt, Lateral Pull and Quality of Movement tests for patellofemoral pain reached moderate to good inter-rater reliability (k = 0.49 to 0.73). Many physical tests appear to reach good inter-rater reliability, but this is based on low-quality and conflicting evidence. High-quality research is required to evaluate the reliability of knee physical examination tests. Copyright © 2016 Elsevier Ltd. All rights reserved.

Characterizing experiments of the PPOOLEX test facility

Energy Technology Data Exchange (ETDEWEB)

Puustinen, M.; Laine, J. (Lappeenranta Univ. of Technology, Nuclear Safety Research Unit (Finland))

2008-07-15

This report summarizes the results of the characterizing test series in 2007 with the scaled down PPOOLEX facility designed and constructed at Lappeenranta University of Technology. Air and steam/air mixture was blown into the dry well compartment and from there through a DN200 blowdown pipe to the condensation pool (wet well). Altogether eight air and four steam/air mixture experiments, each consisting of several blows (tests), were carried out. The main purpose of the experiment series was to study the general behavior of the facility and the performance of basic instrumentation. Proper operation of automation, control and safety systems was also tested. The test facility is a closed stainless steel vessel divided into two compartments, dry well and wet well. The facility is equipped with high frequency measurements for capturing different aspects of the investigated phenomena. The general behavior of the PPOOLEX facility differs significantly from that of the previous POOLEX facility because of the closed two-compartment structure of the test vessel. Heat-up by several tens of degrees due to compression in both compartments was the most obvious evidence of this. Temperatures also stratified. Condensation oscillations and chugging phenomenon were encountered in those tests where the fraction of non-condensables had time to decrease significantly. A radical change from smooth condensation behavior to oscillating one occurred quite abruptly when the air fraction of the blowdown pipe flow dropped close to zero. The experiments again demonstrated the strong diminishing effect that noncondensable gases have on dynamic unsteady loadings experienced by submerged pool structures. BWR containment like behavior related to the beginning of a postulated steam line break accident was observed in the PPOOLEX test facility during the steam/air mixture experiments. The most important task of the research project, to produce experimental data for code simulation purposes, can be

K-Basin spent nuclear fuel characterization data report

International Nuclear Information System (INIS)

Abrefah, J.; Gray, W.J.; Ketner, G.L.; Marschman, S.C.; Pyecha, T.D.; Thornton, T.A.

1995-11-01

The spent nuclear fuel (SNF) project characterization activities will be furnishing technical data on SNF stored at the K Basins in support of a pathway for placement of a ''stabilized'' form of SNF into an interim storage facility. This report summarizes the results so far of visual inspection of the fuel samples, physical characterization (e.g., weight and immersion density measurements), metallographic examinations, and controlled atmosphere furnace testing of three fuel samples shipped from the KW Basin to the Postirradiation Testing Laboratory (PTL). Data on sludge material collected by filtering the single fuel element canister (SFEC) water are also discussed in this report

Verifying Digital Components of Physical Systems: Experimental Evaluation of Test Quality

Science.gov (United States)

Laputenko, A. V.; López, J. E.; Yevtushenko, N. V.

2018-03-01

This paper continues the study of high quality test derivation for verifying digital components which are used in various physical systems; those are sensors, data transfer components, etc. We have used logic circuits b01-b010 of the package of ITC'99 benchmarks (Second Release) for experimental evaluation which as stated before, describe digital components of physical systems designed for various applications. Test sequences are derived for detecting the most known faults of the reference logic circuit using three different approaches to test derivation. Three widely used fault types such as stuck-at-faults, bridges, and faults which slightly modify the behavior of one gate are considered as possible faults of the reference behavior. The most interesting test sequences are short test sequences that can provide appropriate guarantees after testing, and thus, we experimentally study various approaches to the derivation of the so-called complete test suites which detect all fault types. In the first series of experiments, we compare two approaches for deriving complete test suites. In the first approach, a shortest test sequence is derived for testing each fault. In the second approach, a test sequence is pseudo-randomly generated by the use of an appropriate software for logic synthesis and verification (ABC system in our study) and thus, can be longer. However, after deleting sequences detecting the same set of faults, a test suite returned by the second approach is shorter. The latter underlines the fact that in many cases it is useless to spend `time and efforts' for deriving a shortest distinguishing sequence; it is better to use the test minimization afterwards. The performed experiments also show that the use of only randomly generated test sequences is not very efficient since such sequences do not detect all the faults of any type. After reaching the fault coverage around 70%, saturation is observed, and the fault coverage cannot be increased anymore. For

International consensus on the most useful physical examination tests used by physiotherapists for patients with headache: A Delphi study.

Science.gov (United States)

Luedtke, K; Boissonnault, W; Caspersen, N; Castien, R; Chaibi, A; Falla, D; Fernández-de-Las-Peñas, C; Hall, T; Hirsvang, J R; Horre, T; Hurley, D; Jull, G; Krøll, L S; Madsen, B K; Mallwitz, J; Miller, C; Schäfer, B; Schöttker-Königer, T; Starke, W; von Piekartz, H; Watson, D; Westerhuis, P; May, A

2016-06-01

A wide range of physical tests have been published for use in the assessment of musculoskeletal dysfunction in patients with headache. Which tests are used depends on a physiotherapist's clinical and scientific background as there is little guidance on the most clinically useful tests. To identify which physical examination tests international experts in physiotherapy consider the most clinically useful for the assessment of patients with headache. Delphi survey with pre-specified procedures based on a systematic search of the literature for physical examination tests proposed for the assessment of musculoskeletal dysfunction in patients with headache. Seventeen experts completed all three rounds of the survey. Fifteen tests were included in round one with eleven additional tests suggested by the experts. Finally eleven physical examination tests were considered clinically useful: manual joint palpation, the cranio-cervical flexion test, the cervical flexion-rotation test, active range of cervical movement, head forward position, trigger point palpation, muscle tests of the shoulder girdle, passive physiological intervertebral movements, reproduction and resolution of headache symptoms, screening of the thoracic spine, and combined movement tests. Eleven tests are suggested as a minimum standard for the physical examination of musculoskeletal dysfunctions in patients with headache. Copyright © 2016 Elsevier Ltd. All rights reserved.

In Situ Vitrification Engineering-Scale Test ES-INEL-4, ES-INEL-5, ES-INEL-6, and ES-INEL-7 Test Plan

International Nuclear Information System (INIS)

Weidner, J.R.; Stoots, P.R.

1990-10-01

The In Situ Vitrification Engineering-Scale Tests ES-4, ES-5, ES-6, and ES-7 Product Characterization Test Plan describes the methods and procedures to be used or the physical and chemical characterization of the solid product(s) resulting from the Idaho National Engineering Laboratory engineering scale in situ vitrification tests ES-4, ES-5, ES-6, and ES-7. The goals of this Test Plan are to insure that the product characterization results are sufficient to meet the data needs of the In Situ Vitrification Program and are technically and legally defensible. Important issues addressed by the test plan include sampling and analysis strategy, sampling procedures, laboratory analysis, sample control and document management, equipment, data reporting and validation, quality assurance, specific routine procedures to assess data representativeness, safety and training program, and data management. 9 refs., 1 fig., 3 tabs

Characterization of the Scale Model Acoustic Test Overpressure Environment using Computational Fluid Dynamics

Science.gov (United States)

Nielsen, Tanner; West, Jeff

2015-01-01

The Scale Model Acoustic Test (SMAT) is a 5% scale test of the Space Launch System (SLS), which is currently being designed at Marshall Space Flight Center (MSFC). The purpose of this test is to characterize and understand a variety of acoustic phenomena that occur during the early portions of lift off, one being the overpressure environment that develops shortly after booster ignition. The pressure waves that propagate from the mobile launcher (ML) exhaust hole are defined as the ignition overpressure (IOP), while the portion of the pressure waves that exit the duct or trench are the duct overpressure (DOP). Distinguishing the IOP and DOP in scale model test data has been difficult in past experiences and in early SMAT results, due to the effects of scaling the geometry. The speed of sound of the air and combustion gas constituents is not scaled, and therefore the SMAT pressure waves propagate at approximately the same speed as occurs in full scale. However, the SMAT geometry is twenty times smaller, allowing the pressure waves to move down the exhaust hole, through the trench and duct, and impact the vehicle model much faster than occurs at full scale. The DOP waves impact portions of the vehicle at the same time as the IOP waves, making it difficult to distinguish the different waves and fully understand the data. To better understand the SMAT data, a computational fluid dynamics (CFD) analysis was performed with a fictitious geometry that isolates the IOP and DOP. The upper and lower portions of the domain were segregated to accomplish the isolation in such a way that the flow physics were not significantly altered. The Loci/CHEM CFD software program was used to perform this analysis.

Development and Application of Diagnostic Test to Identify Students' Misconceptions of Quantum Physics

International Nuclear Information System (INIS)

Halim, A.A.; Meerah, T.S.; Lilia Halim

2009-01-01

A study on students' misconceptions on quantum physics is rarely being done, because the target audience is quite small. It is important to understand quantum physics concepts correctly especially for science students. This study was under taken to help students identify their misconceptions at the early stage. The aim of this study is to develop a diagnostic test which can access the students' misconceptions, and use the findings for the benefits of quantum physics courses. A multiple-choice Quantum Physics Diagnostic Test (QPDT), that involves concepts of light, atomic model, particle-wave dualism, wave function, and potential energy, was administered to 200 university students. The results shows that many students use the classical concepts to describe the quantum phenomenon. For example students describe light only as a wave, an electron only as a particle, and that the atomic structure is parallel to the solar system. To overcome these problems, it is suggested that lecturers spend more time in explaining the basic definitions and using analogies in quantum physics teaching. (author)

Characterization, Leaching, and Filtration Testing for Bismuth Phosphate Sludge (Group 1) and Bismuth Phosphate Saltcake (Group 2) Actual Waste Sample Composites

International Nuclear Information System (INIS)

Lumetta, Gregg J.; Buck, Edgar C.; Daniel, Richard C.; Draper, Kathryn; Edwards, Matthew K.; Fiskum, Sandra K.; Hallen, Richard T.; Jagoda, Lynette K.; Jenson, Evan D.; Kozelisky, Anne E.; MacFarlan, Paul J.; Peterson, Reid A.; Shimskey, Rick W.; Sinkov, Sergey I.; Snow, Lanee A.

2009-01-01

A testing program evaluating actual tank waste was developed in response to Task 4 from the M-12 External Flowsheet Review Team (EFRT) issue response plan.() The test program was subdivided into logical increments. The bulk water-insoluble solid wastes that are anticipated to be delivered to the Waste Treatment and Immobilization Plant (WTP) were identified according to type such that the actual waste testing could be targeted to the relevant categories. Eight broad waste groupings were defined. Samples available from the 222S archive were identified and obtained for testing. The actual waste-testing program included homogenizing the samples by group, characterizing the solids and aqueous phases, and performing parametric leaching tests. Two of the eight defined groups - bismuth phosphate sludge (Group 1) and bismuth phosphate saltcake (Group 2) - are the subjects of this report. The Group 1 waste was anticipated to be high in phosphorus and was implicitly assumed to be present as BiPO4 (however, results presented here indicate that the phosphate in Group 1 is actually present as amorphous iron(III) phosphate). The Group 2 waste was also anticipated to be high in phosphorus, but because of the relatively low bismuth content and higher aluminum content, it was anticipated that the Group 2 waste would contain a mixture of gibbsite, sodium phosphate, and aluminum phosphate. Thus, the focus of the Group 1 testing was on determining the behavior of P removal during caustic leaching, and the focus of the Group 2 testing was on the removal of both P and Al. The waste-type definition, archived sample conditions, homogenization activities, characterization (physical, chemical, radioisotope, and crystal habit), and caustic leaching behavior as functions of time, temperature, and hydroxide concentration are discussed in this report. Testing was conducted according to TP-RPP-WTP-467

Characterization of electron microscopes with binary pseudo-random multilayer test samples

Science.gov (United States)

Yashchuk, Valeriy V.; Conley, Raymond; Anderson, Erik H.; Barber, Samuel K.; Bouet, Nathalie; McKinney, Wayne R.; Takacs, Peter Z.; Voronov, Dmitriy L.

2011-09-01

Verification of the reliability of metrology data from high quality X-ray optics requires that adequate methods for test and calibration of the instruments be developed. For such verification for optical surface profilometers in the spatial frequency domain, a modulation transfer function (MTF) calibration method based on binary pseudo-random (BPR) gratings and arrays has been suggested [1,2] and proven to be an effective calibration method for a number of interferometric microscopes, a phase shifting Fizeau interferometer, and a scatterometer [5]. Here we describe the details of development of binary pseudo-random multilayer (BPRML) test samples suitable for characterization of scanning (SEM) and transmission (TEM) electron microscopes. We discuss the results of TEM measurements with the BPRML test samples fabricated from a WiSi 2/Si multilayer coating with pseudo-randomly distributed layers. In particular, we demonstrate that significant information about the metrological reliability of the TEM measurements can be extracted even when the fundamental frequency of the BPRML sample is smaller than the Nyquist frequency of the measurements. The measurements demonstrate a number of problems related to the interpretation of the SEM and TEM data. Note that similar BPRML test samples can be used to characterize X-ray microscopes. Corresponding work with X-ray microscopes is in progress.

Characterization of electron microscopes with binary pseudo-random multilayer test samples

International Nuclear Information System (INIS)

Yashchuk, Valeriy V.; Conley, Raymond; Anderson, Erik H.; Barber, Samuel K.; Bouet, Nathalie; McKinney, Wayne R.; Takacs, Peter Z.; Voronov, Dmitriy L.

2011-01-01

Verification of the reliability of metrology data from high quality X-ray optics requires that adequate methods for test and calibration of the instruments be developed. For such verification for optical surface profilometers in the spatial frequency domain, a modulation transfer function (MTF) calibration method based on binary pseudo-random (BPR) gratings and arrays has been suggested and proven to be an effective calibration method for a number of interferometric microscopes, a phase shifting Fizeau interferometer, and a scatterometer [5]. Here we describe the details of development of binary pseudo-random multilayer (BPRML) test samples suitable for characterization of scanning (SEM) and transmission (TEM) electron microscopes. We discuss the results of TEM measurements with the BPRML test samples fabricated from a WiSi 2 /Si multilayer coating with pseudo-randomly distributed layers. In particular, we demonstrate that significant information about the metrological reliability of the TEM measurements can be extracted even when the fundamental frequency of the BPRML sample is smaller than the Nyquist frequency of the measurements. The measurements demonstrate a number of problems related to the interpretation of the SEM and TEM data. Note that similar BPRML test samples can be used to characterize X-ray microscopes. Corresponding work with X-ray microscopes is in progress.

Draft Underground Test Plan for site characterization and testing in an exploratory shaft facility in salt

International Nuclear Information System (INIS)

1987-05-01

An exploratory shaft facility (ESF) at the Deaf Smith County, Texas is a potential candidate repository site in salt. This program of underground testing constitutes part of the effort to determine site suitability, provide data for repository design and performance assessment, and prepare licensing documentation. This program was developed by defining the information needs, as derived from the governing regulatory requirements and associated performance issues; evaluating the efficacy of available tests in satisfying the information needs; and selecting the suite of underground tests that are most cost-effective and timely, considering the other surface-based, surface borehole, and laboratory test programs. Tests are described conceptually, categorized in terms of geology, geomechanics, thermomechanics, geohydrology, or geochemistry, and range in scope from site characterization to site/engineered system interactions. The testing involves construction testing, conducted in the shafts during construction, and in situ testing at depth, conducted in the shafts and in the at-depth test facility at the repository horizon after shaft connection. 41 refs., 67 figs., 16 tabs

USA/FBR program fast flux test facility startup physics and reactor characterization methods and results

International Nuclear Information System (INIS)

Bennett, R.A.; Harris, R.A.; Daughtry, J.W.

1981-09-01

Final confirmation of much of the engineering mockup work has been achieved in FTR zero-power experiments in February, 1980, and in power demonstration performed in December, 1980, and March, 1981. Final in-core low-power and high-power irradiation of spatially distributed radioactivants will be completed late in 1981. This paper describes physics experiments and present summaries of the extensive results accumulated to date. 53 figures

Rock-physics and seismic-inversion based reservoir characterization of the Haynesville Shale

International Nuclear Information System (INIS)

Jiang, Meijuan; Spikes, Kyle T

2016-01-01

Seismic reservoir characterization of unconventional gas shales is challenging due to their heterogeneity and anisotropy. Rock properties of unconventional gas shales such as porosity, pore-shape distribution, and composition are important for interpreting seismic data amplitude variations in order to locate optimal drilling locations. The presented seismic reservoir characterization procedure applied a grid-search algorithm to estimate the composition, pore-shape distribution, and porosity at the seismic scale from the seismically inverted impedances and a rock-physics model, using the Haynesville Shale as a case study. All the proposed rock properties affected the seismic velocities, and the combined effects of these rock properties on the seismic amplitude were investigated simultaneously. The P- and S-impedances correlated negatively with porosity, and the V _P/V _S correlated positively with clay fraction and negatively with the pore-shape distribution and quartz fraction. The reliability of these estimated rock properties at the seismic scale was verified through comparisons between two sets of elastic properties: one coming from inverted impedances, which were obtained from simultaneous inversion of prestack seismic data, and one derived from these estimated rock properties. The differences between the two sets of elastic properties were less than a few percent, verifying the feasibility of the presented seismic reservoir characterization. (paper)

Characterization of basic physical properties of Sb2Se3 and its relevance for photovoltaics

Institute of Scientific and Technical Information of China (English)

Chao CHEN; Matthew C.BEARD; Jiang TANG; David C.BOBELA; Ye YANG; Shuaicheng LU; Kai ZENG; Cong GE; Bo YANG; Liang GAO; Yang ZHAO

2017-01-01

Antimony selenide (Sb2Se3) is a promising absorber material for thin film photovoltaics because of its attractive material,optical and electrical properties.In recent years,the power conversion efficiency (PCE) of Sb2Se3 thin film solar cells has gradually enhanced to 5.6％.In this article,we systematically studied the basic physical properties of Sb2Se3 such as dielectric constant,anisotropic mobility,carrier lifetime,diffusion length,defect depth,defect density and optical band tail states.We believe such a comprehensive characterization of the basic physical properties of Sb2Se3 lays a solid foundation for further optimization of solar device performance.

Physical and mechanical testing of essential oil-embedded cellulose ester films

Science.gov (United States)

Polymer films made from cellulose esters are useful for embedding plant essential oils, either for food packaging or air freshener applications. Studies and testing were done on the physical and mechanical properties of cellulose ester-based films incorporating essential oils (EO) from lemongrass (C...

Characterization of parameters and strategies used by physical therapists in difficult mechanical ventilation weaning

Directory of Open Access Journals (Sweden)

Fabíola Maria Sabino Meireles

2013-03-01

Full Text Available Objective: To characterize the main strategies and parameters used by physical therapists in difficult mechanical ventilation weaning. Methods: Cross-sectional study including all the physical therapists working in adult Intensive Care Units in three public hospitals in Fortaleza-CE. A questionnaire with closed questions related to difficult mechanical ventilation weaning was applied, with either one or multiple answers. The data was treated with descriptive and non-parametric analysis. Results: Among the parameters mostly used by the 56 interviewed physical therapists for the difficult weaning, were found: current volume reduction (26 - 46.4% and desaturation during aspiration (17 - 30.4%. It was observed that 38 (67.9% alternate T-tube and continuous positive airway pressure (CPAP as strategies for difficult weaning, and 28 (50% reported reducing the pressure support. There was no statistical difference between the strategies used in the studied hospitals, neither correlation between strategies and parameters. Conclusion: It was found that physical therapists have been performing similar strategies, which are also shown in the literature, but this is not the case with the parameters. The parameters used are not supported by the literature.

Characterization of the aspects of osteoprogenitor cell interactions with physical tetracalcium phosphate anchorage on titanium implant surfaces

Energy Technology Data Exchange (ETDEWEB)

Ko, Chia-Ling [Advanced Medical Devices and Composites Laboratory, Department of Fiber and Composite Materials, Feng Chia University, Taichung 40724, Taiwan (China); Dental Medical Devices and Materials Research Center, College of Dental Medicine, Kaohsiung Medical University, Kaohsiung 807, Taiwan (China); Chang, Ya-Yuan; Liou, Cian-Hua [Alliance Global Technology Co., Ltd., Kaohsiung Medical Device Special Zone in Southern Taiwan Science Park, Kaohsiung 82151, Taiwan (China); Chen, Wen-Cheng, E-mail: wencchen@fcu.edu.tw [Advanced Medical Devices and Composites Laboratory, Department of Fiber and Composite Materials, Feng Chia University, Taichung 40724, Taiwan (China)

2015-04-01

Well-designed implants are used not only to modify the geometry of the implant but also to change the chemical properties of its surfaces. The present study aims to assess the biofunctional effects of tetracalcium phosphate (TTCP) particles as a physical anchor on the implant surface derived through sandblasting. The characteristics of the surface, cell viability, and alkaline phosphatase (ALP) activity toward osteoprogenitor cells (D1) were obtained. D1 cells were cultured on a plain surface that underwent sandblasting and acid etching (SLA) (control SLA group) and on different SLA surfaces with different anchoring TTCP rates (new test groups, M and H). The mean anchoring rates were 57% (M) and 74% (H), and the anchored thickness was estimated to range from 12.6 μm to 18.3 μm. Compared with the control SLA surface on Ti substrate, the new test groups with different TTCP anchoring rates (M and H) failed to improve cell proliferation significantly but had a well-differentiated D1 cell phenotype that enhanced ALP expression in the early stage of cell cultures, specifically, at day 7. Results suggest that the SLA surface with anchored TTCP can accelerate progenitor bone cell mineralization. This study shows the potential clinical application of the constructed geometry in TTCP anchorage on Ti for dental implant surface modification. - Highlights: • TTCP (tetracalcium phosphate) as a physical anchorage on implant is characterized. • Theoretical values of anchored thickness and capping areas were estimated. • TTCP anchored by sandblasting can accelerate progenitor bone cell mineralization. • TTCP anchored on SLA (sandblasting and acid etching) surface is a promising method.

Characterization of the aspects of osteoprogenitor cell interactions with physical tetracalcium phosphate anchorage on titanium implant surfaces

International Nuclear Information System (INIS)

Ko, Chia-Ling; Chang, Ya-Yuan; Liou, Cian-Hua; Chen, Wen-Cheng

2015-01-01

Well-designed implants are used not only to modify the geometry of the implant but also to change the chemical properties of its surfaces. The present study aims to assess the biofunctional effects of tetracalcium phosphate (TTCP) particles as a physical anchor on the implant surface derived through sandblasting. The characteristics of the surface, cell viability, and alkaline phosphatase (ALP) activity toward osteoprogenitor cells (D1) were obtained. D1 cells were cultured on a plain surface that underwent sandblasting and acid etching (SLA) (control SLA group) and on different SLA surfaces with different anchoring TTCP rates (new test groups, M and H). The mean anchoring rates were 57% (M) and 74% (H), and the anchored thickness was estimated to range from 12.6 μm to 18.3 μm. Compared with the control SLA surface on Ti substrate, the new test groups with different TTCP anchoring rates (M and H) failed to improve cell proliferation significantly but had a well-differentiated D1 cell phenotype that enhanced ALP expression in the early stage of cell cultures, specifically, at day 7. Results suggest that the SLA surface with anchored TTCP can accelerate progenitor bone cell mineralization. This study shows the potential clinical application of the constructed geometry in TTCP anchorage on Ti for dental implant surface modification. - Highlights: • TTCP (tetracalcium phosphate) as a physical anchorage on implant is characterized. • Theoretical values of anchored thickness and capping areas were estimated. • TTCP anchored by sandblasting can accelerate progenitor bone cell mineralization. • TTCP anchored on SLA (sandblasting and acid etching) surface is a promising method

Physical properties and characterization of Ag doped CdS thin films

International Nuclear Information System (INIS)

Shah, N.A.; Nazir, A.; Mahmood, W.; Syed, W.A.A.; Butt, S.; Ali, Z.; Maqsood, A.

2012-01-01

Highlights: ► CdS thin films were grown. ► By ion exchange, Ag was doped. ► Physical properties were investigated. - Abstract: Thin films of cadmium sulfide with very well defined preferential orientation and relatively high absorption coefficient were fabricated by thermal evaporation technique. The research is focused to the fabrication and characterization of the compositional data of CdS thin films obtained by using X-ray diffraction, scanning electron microscope along with energy dispersive X-ray spectroscopy. The optical properties were studied by using a UV-VIS-NIR spectrophotometer. The effects of silver-doping by ion exchange process on the properties of as-deposited CdS thin films have been investigated.

Characterization of holding brake friction pad surface after pin-on-plate wear test

DEFF Research Database (Denmark)

Drago, N.; Gonzalez Madruga, D.; De Chiffre, L.

2018-01-01

This article concerns the metrological characterization of the surface on a holding brake friction material pin after a pin-on-plate (POP) wear test. The POP test induces the formation of surface plateaus that affect brake performances such as wear, friction, noise and heat. Three different...

Electrostatic discharge attenuation test for the characterization of ESD protective materials

International Nuclear Information System (INIS)

Paasi, Jaakko; Viheriaekoski, Toni; Sutela, Lassi; Tamminen, Pasi K

2008-01-01

New experimental method has been developed to evaluate materials, tools, equipment and packaging used in the electronics production environment under Charged Device Model (CDM) type of electrostatic discharge (ESD) transients. The method is intended to characterize the ability of the material or object to attenuate ESD energy and peak discharge current when a charged device is discharged into the material under test. The test is supplementary for the standard quasi-static measurements of ESD control programs in the cases where standard measurements do not give sufficient information due to voltage non-linearity, complexity or shape of the material or object under test.

Fabrication and characterization of MCC approved testing material - ATM-8 glass

International Nuclear Information System (INIS)

Wald, J.W.

1985-10-01

The Materials Characterization Center (MCC) Approved Testing Material ATM-8 is a borosilicate glass that incorporates elements typical of high-level waste (HLW) resulting from the reprocessing of commercial nuclear reactor fuel. Its composition is based upon the simulated HLW glass type 76-68 (Mendel, J.E. et al., 1977, Annual Report of the Characteristics of High-Level Waste Glasses, BNWL-2252, Pacific Northwest Laboratory, Richland, Washington), to which depleted uranium, technetium-99, neptunium-237 and plutonium-239 have been added at moderate to low levels. The glass was requested by the Nevada Nuclear Waste Storage Investigations (NNWSI) Project. It was produced by the MCC at the Pacific Northwest Laboratory (PNL) operated for the Department of Energy (DOE) by Battelle Memorial Institute. ATM-8 glass was produced in April of 1984, and is the second in a series of testing materials for NNWSI. This report discusses its fabrication (starting materials, batch and glass preparation, measurement and testing equipment, other equipment, procedures, identification system and materials availability and storage, and characterization (bulk density) measurements, chemical analysis, microscopic examination, and x-ray diffraction analysis. 4 refs., 2 figs., 10 tabs

The reliability of physical examination tests for the diagnosis of anterior cruciate ligament rupture--A systematic review.

Science.gov (United States)

Lange, Toni; Freiberg, Alice; Dröge, Patrik; Lützner, Jörg; Schmitt, Jochen; Kopkow, Christian

2015-06-01

Systematic literature review. Despite their frequent application in routine care, a systematic review on the reliability of clinical examination tests to evaluate the integrity of the ACL is missing. To summarize and evaluate intra- and interrater reliability research on physical examination tests used for the diagnosis of ACL tears. A comprehensive systematic literature search was conducted in MEDLINE, EMBASE and AMED until May 30th 2013. Studies were included if they assessed the intra- and/or interrater reliability of physical examination tests for the integrity of the ACL. Methodological quality was evaluated with the Quality Appraisal of Reliability Studies (QAREL) tool by two independent reviewers. 110 hits were achieved of which seven articles finally met the inclusion criteria. These studies examined the reliability of four physical examination tests. Intrarater reliability was assessed in three studies and ranged from fair to almost perfect (Cohen's k = 0.22-1.00). Interrater reliability was assessed in all included studies and ranged from slight to almost perfect (Cohen's k = 0.02-0.81). The Lachman test is the physical tests with the highest intrarater reliability (Cohen's k = 1.00), the Lachman test performed in prone position the test with the highest interrater reliability (Cohen's k = 0.81). Included studies were partly of low methodological quality. A meta-analysis could not be performed due to the heterogeneity in study populations, reliability measures and methodological quality of included studies. Systematic investigations on the reliability of physical examination tests to assess the integrity of the ACL are scarce and of varying methodological quality. Copyright © 2014 Elsevier Ltd. All rights reserved.

Teaching and testing physical examination skills without the use of patients.

Science.gov (United States)

Karnath, Bernard; Thornton, William; Frye, Ann W

2002-07-01

To design a cardiopulmonary physical exam curriculum that does not involve the use of patients. Bedside teaching is becoming a lost art, and the use of alternative methods of instruction such as simulation has become increasingly important. Simulators have been shown to enhance physical examination skills of students and physicians in training.(1) In 1995, a program was started to improve cardiopulmonary physical diagnosis and the teaching of auscultation at the University of Texas Medical Branch at Galveston (UTMB). The teaching manikin "Harvey" played a vital role in the development of the new curriculum. In 1997, UTMB adopted an organ-based approach to the basic science curriculum. The cardiopulmonary module in the basic science curriculum was a ten-week course taught in the second year of medical school. The physical diagnosis section of that course involved six instructional hours; four of the six hours were dedicated to cardiac auscultation and two hours to pulmonary auscultation. Only simulators and CD-ROMs were used for instruction. The 184 second-year medical students at UTMB were formed into small groups for instruction and practice. Although "Harvey" was an effective teaching tool, other simulators had to be developed for testing students' skills after instruction. It would be very difficult to administer a skills OSCE for 184 students without the development of several smaller transportable simulators. A commercially available blood pressure simulator from the Medical Plastics Laboratory, Inc., Gatesville, TX, was used to test the accuracy of students' blood pressure readings. Small auscultation transducers combined with a palpable pulse simulator, developed by one of the authors (WT) in collaboration with Andries Acoustics, Spicewood, TX, were used to efficiently test students' proficiency in cardiopulmonary auscultation. Digital simulated cardiopulmonary sounds were recorded onto a standard CD-ROM mini-disc and transmitted to the small transducers

Characterizing Corrosion Effects of Weak Organic Acids Using a Modified Bono Test

Science.gov (United States)

Zhou, Yuqin; Turbini, Laura J.; Ramjattan, Deepchand; Christian, Bev; Pritzker, Mark

2013-12-01

To meet environmental requirements and achieve benefits of cost-effective manufacturing, no-clean fluxes (NCFs) or low-solids fluxes have become popular in present electronic manufacturing processes. Weak organic acids (WOAs) as the activation ingredients in NCFs play an important role, especially in the current lead-free and halogen-free soldering technology era. However, no standard or uniform method exists to characterize the corrosion effects of WOAs on actual metallic circuits of printed wiring boards (PWBs). Hence, the development of an effective quantitative test method for evaluating the corrosion effects of WOAs on the PWB's metallic circuits is imperative. In this paper, the modified Bono test, which was developed to quantitatively examine the corrosion properties of flux residues, is used to characterize the corrosion effects of five WOAs (i.e., abietic acid, succinic acid, glutaric acid, adipic acid, and malic acid) on PWB metallic circuits. Experiments were performed under three temperature/humidity conditions (85°C/85% RH, 60°C/93% RH, and 40°C/93% RH) using two WOA solution concentrations. The different corrosion effects among the various WOAs were best reflected in the testing results at 40°C and 60°C. Optical microscopy was used to observe the morphology of the corroded copper tracks, and scanning electron microscopy (SEM) energy-dispersive x-ray (EDX) characterization was performed to determine the dendrite composition.

Large-scale in situ heater tests for hydrothermal characterization at Yucca Mountain

International Nuclear Information System (INIS)

Buscheck, T.A.; Wilder, D.G.; Nitao, J.J.

1993-01-01

To safely and permanently store high-level nuclear waste, the potential Yucca Mountain repository site must mitigate the release and transport of radionuclides for tens of thousands of years. In the failure scenario of greatest concern, water would contact a waste package, accelerate its failure rate, and eventually transport radionuclides to the water table. Our analyses indicate that the ambient hydrological system will be dominated by repository-heat-driven hydrothermal flow for tens of thousands of years. In situ heater tests are required to provide an understanding of coupled geomechanical-hydrothermal-geochemical behavior in the engineered and natural barriers under repository thermal loading conditions. In situ heater tests have been included in the Site Characterization Plan in response to regulatory requirements for site characterization and to support the validation of process models required to assess the total systems performance at the site. Because of limited time, some of the in situ tests will have to be accelerated relative to actual thermal loading conditions. We examine the trade-offs between the limited test duration and generating hydrothermal conditions applicable to repository performance during the entire thermal loading cycle, including heating (boiling and dry-out) and cooldown (re-wetting). For in situ heater tests to be applicable to actual repository conditions, a minimum heater test duration of 6-7 yr (including 4 yr of full-power heating) is required

Demonstration of load rating capabilities through physical load testing : Sioux County bridge case study.

Science.gov (United States)

2013-08-01

The objective of this work, Pilot Project - Demonstration of Capabilities and Benefits of Bridge Load Rating through Physical Testing, was to demonstrate the capabilities for load testing and rating bridges in Iowa, study the economic benefit of perf...

Demonstration of load rating capabilities through physical load testing : Johnson County bridge case study.

Science.gov (United States)

2013-08-01

The objective of this work, Pilot Project - Demonstration of Capabilities and Benefits of Bridge Load Rating through Physical Testing, was to demonstrate the capabilities for load testing and rating bridges in Iowa, study the economic benefit of perf...

Demonstration of load rating capabilities through physical load testing : Ida County bridge case study.

Science.gov (United States)

2013-08-01

The objective of this work, Pilot Project - Demonstration of Capabilities and Benefits of Bridge Load Rating through Physical Testing, was to demonstrate the capabilities for load testing and rating bridges in Iowa, study the economic benefit of perf...

Characterization of radioactive mixed wastes: The industrial perspective

International Nuclear Information System (INIS)

Leasure, C.S.

1992-01-01

Physical and chemical characterization of Radioactive Mixed Wastes (RMW) is necessary for determination of appropriate treatment options and to satisfy environmental regulations. Radioactive mixed waste can be classified as two main categories; contact-handled (low level) RMW and remote-handled RMW. Ibis discussion will focus mainly on characterization of contact handled RMW. The characterization of wastes usually follows one of two pathways: (1) characterization to determine necessary parameters for treatment or (2) characterization to determine if the material is a hazardous waste. Sometimes, however, wastes can be declared as hazardous waste without testing and then treated as hazardous waste. Characterization of radioactive mixed wastes pose some unique issues, however, that will require special solutions. Below, five issues affecting sampling and analysis of RMW will be discussed

Testing an MCM for high-energy physics experiments a case study

CERN Document Server

Benso, A; Prinetto, P; Giovannetti, S; Mariani, R; Motto, S

1999-01-01

This paper presents the test strategy adopted at different hierarchical abstraction levels (from board to die level) during the development of a multichannel data acquisition and signal processing MCM, designed for the new generation experiments of high-energy physics on the Large Hadron Collider accelerator at CERN. (10 refs).

8th RILEM International Symposium on Testing and Characterization of Sustainable and Innovative Bituminous Materials

CERN Document Server

Partl, Manfred

2016-01-01

This work presents the results of RILEM TC 237-SIB (Testing and characterization of sustainable innovative bituminous materials and systems). The papers have been selected for publication after a rigorous peer review process and will be an invaluable source to outline and clarify the main directions of present and future research and standardization for bituminous materials and pavements. The following topics are covered: - Characterization of binder-aggregate interaction - Innovative testing of bituminous binders, additives and modifiers - Durability and aging of asphalt pavements - Mixture design and compaction analysis - Environmentally sustainable materials and technologies - Advances in laboratory characterization of bituminous materials - Modeling of road materials and pavement performance prediction - Field measurement and in-situ characterization - Innovative materials for reinforcement and interlayer systems - Cracking and damage characterization of asphalt pavements - Rec...

Characterization testing of a 40 Ahr bipolar nickel hydrogen battery

Science.gov (United States)

Brewer, Jeffrey C.; Manzo, Michelle A.; Gahn, Randall F.

1989-01-01

In a continuing effort to develop NiH2 bipolar technology to a point where it can be used efficiently in space flight, testing of a second 40 Ahr, 10-cell bipolar battery has begun. This battery has undergone extensive characterization testing to determine the effects of such operating parameters as charge and discharge rates, temperature, and pressure. The fundamental design of this actively cooled bipolar battery is the same as the first battery. Most of the individual components, however, are from different manufacturers. Different testing procedures as well as certain unique battery characteristics make it difficult to directly compare the two sets of results. In general, the performance of this battery throughout characterization produced expected results. The main differences seen between the first and second batteries occurred during the high-rate discharge portion of the test matrix. The first battery also had poor high-rate discharge results, although better than those of the second battery. Minor changes were made to the battery frame design used for the first battery in an attempt to allow better gas access to the reaction sites for the second build and hopefully improve performance. The changes, however, did not improve the performance of the second battery and could have possibly contributed to the poorer performance that was observed. There are other component differences that could have contributed to the poorer performance of the second battery. The H2 electrode in the second battery was constructed with a Goretex backing which could have limited the high-rate current flow. The gas screen in the second battery had a larger mesh which again could have limited the high-rate current flow. Small scale 2 x 2 batteries are being tested to evaluate the effects of the component variations.

Physical-Chemical Characterization and Formulation Considerations for Solid Lipid Nanoparticles.

Science.gov (United States)

Chauhan, Harsh; Mohapatra, Sarat; Munt, Daniel J; Chandratre, Shantanu; Dash, Alekha

2016-06-01

Pure glyceryl mono-oleate (GMO) (lipid) and different batches of GMO commonly used for the preparation of GMO-chitosan nanoparticles were characterized by modulated differential scanning calorimetry (MDSC), cryo-microscopy, and cryo-X-ray powder diffraction techniques. GMO-chitosan nanoparticles containing poloxamer 407 as a stabilizer in the absence and presence of polymers as crystallization inhibitors were prepared by ultrasonication. The effect of polymers (polyvinyl pyrrolidone (PVP), Eudragits, hydroxyl propyl methyl cellulose (HPMC), polyethylene glycol (PEG)), surfactants (poloxamer), and oils (mineral oil and olive oil) on the crystallization of GMO was investigated. GMO showed an exothermic peak at around -10°C while cooling and another exothermic peak at around -12°C while heating. It was followed by two endothermic peaks between 15 and 30 C, indicative of GMO melting. The results are corroborated by cryo-microscopy and cryo-X-ray. Significant differences in exothermic and endothermic transition were observed between different grades of GMO and pure GMO. GMO-chitosan nanoparticles resulted in a significant increase in particle size after lyophilization. MDSC confirmed that nanoparticles showed similar exothermic crystallization behavior of lipid GMO. MDSC experiments showed that PVP inhibits GMO crystallization and addition of PVP showed no significant increase in particle size of solid lipid nanoparticle (SLN) during lyophilization. The research highlights the importance of extensive physical-chemical characterization for successful formulation of SLN.

Physics design of fast reactor safety test facilities for in-pile experiments

International Nuclear Information System (INIS)

Travelli, A.; Matos, J.E.; Snelgrove, J.L.; Shaftman, D.H.; Tzanos, C.P.; Lam, S.K.; Pennington, E.M.; Woodruff, W.L.

1976-01-01

A determined effort to identify and resolve current Fast Breeder Reactor safety testing needs has recently resulted in a number of conceptual designs for FBR safety test facilities which are very complex and diverse both in their features and in their purpose. The paper discusses the physics foundations common to most fast reactor safety test facilities and the constraints which they impose on the design. The logical evolution, features, and capabilities of several major conceptual designs are discussed on the basis of this common background

[Physical fitness in relation to age and body build of young chess players].

Science.gov (United States)

Fornal-Urban, Agnieszka; Keska, Anna; Dobosz, Janusz; Nowacka-Dobosz, Sylwia

2009-01-01

Specificity of chess training promotes sedentary lifestyle and may reduce chess players participation in different physical activities. Limited physical activity leads to decrease of physical fitness and may augment the risk of overweight and obesity. It is suggested that these athletes will characterize more frequently lower physical fitness and weight/height proportions disorders. The aim of the study was evaluation of physical fitness and its relationship with age and body build of athletes. A sample of 73 individuals (35 girls--48% and 38 boys--52%) aged 8-19 years took part in this study. All competitors were members of national team and Polish representatives for the European and world chess championship. Chess players' physical fitness was measured by EUROFIT tests. With reference to the Polish population chess players characterized higher level of physical fitness. In six tests of EUROFIT chess players had better standardized results than controls. Sit ups (mean standardized result 0.842), shuttle run 10 x 5 m (0.577), standing broad jump (0.552) and flamingo balance (0.371) were very well performed by chess players. Only in one test, bent arm hang, sportsmen achieved worse results (-0.719). Permanent decrease of chess players' physical fitness with age was also observed. Although chess players' physical fitness was satisfied in comparison to age-matched control, it is recommended to include in their training more exercises developing strength. Because of changes in body build with age and decrease of physical fitness, chess players ought to participate in regular physical activity. Therefore chess organisers should provide the variety of active forms that can be chosen by competitors in their leisure time.

Obtaining and characterization catalyst Ki/Al_2O_3 by physical dispersion process via wet

International Nuclear Information System (INIS)

Silva, M.C. da; Dantas, J.; Costa, A.C.F.M.; Costa, N.C.O.; Freitas, N.L. de

2014-01-01

The aim of this study is the Obtention and characterization of catalysts being supported alumina impregnated with KI by physical dispersion in wet via attritor mill in periods of 30 and 60 minutes. Before and after impregnation the catalysts were characterized by XRD, X ray fluorescence, particle size distribution, textural analysis (BET). The results show the presence of the stable crystalline phase Al_2O_3 in all samples after impregnation and the second phase formed from KI and K_2O. There was a decrease in the agglomerates incorporated with the potassium due to the milling process. It was observed that the highest specific surface area was obtained by the impregnated sample into a 60 min. (author)

Nondestructive characterization of ductile cast iron by magnetic adaptive testing

Czech Academy of Sciences Publication Activity Database

Vértesy, G.; Uchimoto, T.; Tomáš, Ivan; Takagi, T.

2010-01-01

Roč. 322, č. 20 (2010), s. 3117-3121 ISSN 0304-8853 R&D Projects: GA ČR GA101/09/1323; GA AV ČR 1QS100100508 Institutional research plan: CEZ:AV0Z10100520 Keywords : magnetic NDE * magnetic adaptive testing * magnetic hysteresis * cast iron Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.689, year: 2010

QED Tests and Search for New Physics in Molecular Hydrogen

Science.gov (United States)

Salumbides, E. J.; Niu, M. L.; Dickenson, G. D.; Eikema, K. S. E.; Komasa, J.; Pachucki, K.; Ubachs, W.

2013-06-01

The hydrogen molecule has been the benchmark system for quantum chemistry, and may provide a test ground for new physics. We present our high-resolution spectroscopic studies on the X ^1Σ^+_g electronic ground state rotational series and fundamenal vibrational tones in molecular hydrogen. In combination with recent accurate ab initio calculations, we demonstrate systematic tests of quantum electrodynamical (QED) effects in molecules. Moreover, the precise comparison between theory and experiment can provide stringent constraints on possible new interactions that extend beyond the Standard Model. E. J. Salumbides, G. D. Dickenson, T. I. Ivanov and W. Ubachs, Phys. Rev. Lett. 107, 043005 (2011).

Characterization Report Operational Closure Covers for the Area 5 Radioactive Waste Management Site at the Nevada Test Site

International Nuclear Information System (INIS)

Bechtel Nevada Geotechnical Sciences

2005-01-01

Bechtel Nevada (BN) manages two low-level Radioactive Waste Management Sites (RWMSs) at the Nevada Test Site (NTS) for the U.S. Department of Energy (DOE) National Nuclear Security Administration Nevada Site Office (NNSA/NSO). The Area 3 RWMS is located in south-central Yucca Flat and the Area 5 RWMS is located about 15 miles south, in north-central Frenchman Flat. Though located in two separate topographically closed basins, they are similar in climate and hydrogeologic setting. The Area 5 RWMS uses engineered shallow-land burial cells to dispose of packaged waste, while the Area 3 RWMS uses subsidence craters formed from underground testing of nuclear weapons for the disposal of packaged and unpackaged bulk waste. Over the next several decades, most waste disposal units at both the Area 3 and Area 5 RWMSs are anticipated to be closed. Closure of the Area 3 and Area 5 RWMSs will proceed through three phases: operational closure, final closure, and institutional control. Many waste disposal units at the Area 5RWMS are operationally closed and final closure has been placed on one unit at the Area 3 RWMS (U-3ax/bl). Because of the similarities between the two sites (e.g., type of wastes, environmental factors, operational closure cover designs, etc.), many characterization studies and data collected at the Area 3 RWMS are relevant and applicable to the Area 5 RWMS. For this reason, data and closure strategies from the Area 3 RWMS are referred to as applicable. This document is an interim Characterization Report - Operational Closure Covers, for the Area 5 RWMS. The report briefly describes the Area 5 RWMS and the physical environment where it is located, identifies the regulatory requirements, reviews the approach and schedule for closing, summarizes the monitoring programs, summarizes characterization studies and results, and then presents conclusions and recommendations

Development of the Occupational Physical Assessment Test (OPAT) for Combat Arms Soldiers

Science.gov (United States)

2015-10-01

dragged was measured. A rubber flooring (4’ x 6’ x 3/4" Interlocking Diamond Plate Tiles, Kodiak Sports , Plano, TX) was used as a standardized surface... knocking over the cones. Time to complete the course was recorded (11 ). All testing instructions and data collection sheets can be found in...acceptability of the prediction test battery. 25 REFERENCES 1. American College of Sports Medicine. ACSMs Health - Related Physical Fitness

Diagnostic validity of physical examination tests for common knee disorders: An overview of systematic reviews and meta-analysis.

Science.gov (United States)

Décary, Simon; Ouellet, Philippe; Vendittoli, Pascal-André; Roy, Jean-Sébastien; Desmeules, François

2017-01-01

More evidence on diagnostic validity of physical examination tests for knee disorders is needed to lower frequently used and costly imaging tests. To conduct a systematic review of systematic reviews (SR) and meta-analyses (MA) evaluating the diagnostic validity of physical examination tests for knee disorders. A structured literature search was conducted in five databases until January 2016. Methodological quality was assessed using the AMSTAR. Seventeen reviews were included with mean AMSTAR score of 5.5 ± 2.3. Based on six SR, only the Lachman test for ACL injuries is diagnostically valid when individually performed (Likelihood ratio (LR+):10.2, LR-:0.2). Based on two SR, the Ottawa Knee Rule is a valid screening tool for knee fractures (LR-:0.05). Based on one SR, the EULAR criteria had a post-test probability of 99% for the diagnosis of knee osteoarthritis. Based on two SR, a complete physical examination performed by a trained health provider was found to be diagnostically valid for ACL, PCL and meniscal injuries as well as for cartilage lesions. When individually performed, common physical tests are rarely able to rule in or rule out a specific knee disorder, except the Lachman for ACL injuries. There is low-quality evidence concerning the validity of combining history elements and physical tests. Copyright © 2016 Elsevier Ltd. All rights reserved.

Characterization of Settler Tank and KW Container Sludge Simulants

Energy Technology Data Exchange (ETDEWEB)

Burns, Carolyn A.; Luna, Maria; Schmidt, Andrew J.

2009-05-12

The Sludge Treatment Project (STP), managed by CH2M Hill Plateau Remediation Company (CHPRC) has specified base formulations for non-radioactive sludge simulants for use in the development and testing of equipment for sludge sampling, retrieval, transport, and processing. In general, the simulant formulations are based on the average or design-basis physical and chemical properties obtained by characterizing sludge samples. The simulants include surrogates for uranium metal, uranium oxides (agglomerates and fine particulate), and the predominant chemical phases (iron and aluminum hydroxides, sand). Specific surrogate components were selected to match the nominal particle-size distribution and particle-density data obtained from sludge sample analysis. Under contract to CHPRC, Pacific Northwest National Laboratory (PNNL) has performed physical and rheological characterization of simulants, and the results are reported here. Two base simulant types (dry) were prepared by STP staff at the Maintenance and Storage Facility and received by PNNL on February 12, 2009: Settler Tank Simulant and KW Container Sludge Simulant. The objectives of this simulant characterization effort were to provide baseline characterization data on simulants being used by STP for process development and equipment testing and provide a high-level comparison of the simulant characteristics to the targets used to formulate the simulants.

The Association Between Fall History and Physical Performance Tests in the Community-Dwelling Elderly: A Cross-Sectional Analysis.

Science.gov (United States)

Kim, Jin Chul; Chon, Jinmann; Kim, Hee Sang; Lee, Jong Ha; Yoo, Seung Don; Kim, Dong Hwan; Lee, Seung Ah; Han, Yoo Jin; Lee, Hyun Seok; Lee, Bae Youl; Soh, Yun Soo; Won, Chang Won

2017-04-01

To evaluate the association between baseline characteristics, three physical performance tests and fall history in a sample of the elderly from Korean population. A total of 307 participants (mean age, 76.70±4.85 years) were categorized into one of two groups, i.e., fallers and non-fallers. Fifty-two participants who had reported falling unexpectedly at least once in the previous 12 months were assigned to the fallers group. Physical performance tests included Short Physical Performance Battery (SPPB), Berg Balance Scale (BBS), Timed Up and Go test. The differences between the two study groups were compared and we analyzed the correlations between fall histories and physical performance tests. SPPB demonstrated a significant association with fall history. Although the BBS total scores did not show statistical significance, two dynamic balance test items of BBS (B12 and B13) showed a significant association among fallers. This study suggests that SPPB and two dynamic balance test items of the BBS can be used in screening for risk of falls in an ambulatory elderly population.

Comparison of LOFT zero power physics testing measurement results with predicted values

International Nuclear Information System (INIS)

Rushton, B.L.; Howe, T.M.

1978-01-01

The results of zero power physics testing measurements in LOFT have been evaluated to assess the adequacy of the physics data used in the safety analyses performed for the LOFT FSAR and Technical Specifications. Comparisons of measured data with computed data were made for control rod worths, temperature coefficients, boron worths, and pressure coefficients. Measured boron concentrations at exact critical points were compared with predicted concentrations. Based on these comparisons, the reactivity parameter values used in the LOFT safety analyses were assessed for conservatism

Physical Activity Patterns among U.S. Adults with Disabilities

Science.gov (United States)

Chiu, Chung-Yi; An, Ruopeng

2016-01-01

Purpose: To characterize physical activity patterns among people with disabilities using data from a nationally representative health survey. Method: Individual-level data came from the Behavioral Risk Factor Surveillance System 2011 survey. Pearson's chi-squared tests were conducted to assess the difference in the proportion distribution of…

Evaluation of the Initial Isothermal Physics Measurements at the Fast Flux Test Facility, a Prototypic Liquid Metal Fast Breeder Reactor

Energy Technology Data Exchange (ETDEWEB)

John D. Bess

2010-03-01

The Fast Flux Test Facility (FFTF) was a 400-MWt, sodium-cooled, low-pressure, high-temperature, fast-neutron flux, nuclear fission reactor plant designed for the irradiation testing of nuclear reactor fuels and materials for the development of liquid metal fast breeder reactors (LMFBRs). The FFTF was fueled with plutonium-uranium mixed oxide (MOX) and reflected by Inconel-600. Westinghouse Hanford Company operated the FFTF as part of the Hanford Engineering Development Laboratory (HEDL) for the U.S. Department of Energy on the Hanford Site near Richland, Washington. Although the FFTF was a testing facility not specifically designed to breed fuel or produce electricity, it did provide valuable information for LMFBR projects and base technology programs in the areas of plant system and component design, component fabrication, prototype testing, and site construction. The major objectives of the FFTF were to provide a strong, disciplined engineering base for the LMFBR program, provide fast flux testing for other U.S. programs, and contribute to the development of a viable self-sustaining competitive U.S. LMFBR industry. During its ten years of operation, the FFTF acted as a national research facility to test advanced nuclear fuels, materials, components, systems, nuclear power plant operating and maintenance procedures, and active and passive reactor safety technologies; it also produced a large number of isotopes for medical and industrial users, generated tritium for the U.S. fusion research program, and participated in cooperative, international research work. Prior to the implementation of the reactor characterization program, a series of isothermal physics measurements were performed; this acceptance testing program consisted of a series of control rod worths, critical rod positions, subcriticality measurements, maximum reactivity addition rates, shutdown margins, excess reactivity, and isothermal temperature coefficient reactivity. The results of these

Alpha particle physics experiments in the Tokamak Fusion Test Reactor

International Nuclear Information System (INIS)

Zweben, S.J.; Budny, R.V.; Darrow, D.S.; Medley, S.S.; Nazikian, R.; Stratton, B.C.; Synakowski, E.J.; Taylor, G.

2000-01-01

Alpha particle physics experiments were done on TFTR during its DT run from 1993 to 1997. These experiments utilized several new alpha particle diagnostics and hundreds of DT discharges to characterize the alpha particle confinement and wave-particle interactions. In general, the results from the alpha particle diagnostics agreed with the classical single particle confinement model in MHD quiescent discharges. The alpha loss due to toroidal field ripple was identified in some cases, and the low radial diffusivity inferred for high energy alphas was consistent with orbit averaging over small scale turbulence. Finally, the observed alpha particle interactions with sawteeth, toroidal Alfven eigenmodes and ICRF waves were approximately consistent with theoretical modelling. What was learned is reviewed and what remains to be understood is identified. (author)

Characterization of Thermo-Physical Properties of EVA/ATH: Application to Gasification Experiments and Pyrolysis Modeling

Directory of Open Access Journals (Sweden)

Bertrand Girardin

2015-11-01

Full Text Available The pyrolysis of solid polymeric materials is a complex process that involves both chemical and physical phenomena such as phase transitions, chemical reactions, heat transfer, and mass transport of gaseous components. For modeling purposes, it is important to characterize and to quantify the properties driving those phenomena, especially in the case of flame-retarded materials. In this study, protocols have been developed to characterize the thermal conductivity and the heat capacity of an ethylene-vinyl acetate copolymer (EVA flame retarded with aluminum tri-hydroxide (ATH. These properties were measured for the various species identified across the decomposition of the material. Namely, the thermal conductivity was found to decrease as a function of temperature before decomposition whereas the ceramic residue obtained after the decomposition at the steady state exhibits a thermal conductivity as low as 0.2 W/m/K. The heat capacity of the material was also investigated using both isothermal modulated Differential Scanning Calorimetry (DSC and the standard method (ASTM E1269. It was shown that the final residue exhibits a similar behavior to alumina, which is consistent with the decomposition pathway of EVA/ATH. Besides, the two experimental approaches give similar results over the whole range of temperatures. Moreover, the optical properties before decomposition and the heat capacity of the decomposition gases were also analyzed. Those properties were then used as input data for a pyrolysis model in order to predict gasification experiments. Mass losses of gasification experiments were well predicted, thus validating the characterization of the thermo-physical properties of the material.

Characterization of Thermo-Physical Properties of EVA/ATH: Application to Gasification Experiments and Pyrolysis Modeling.

Science.gov (United States)

Girardin, Bertrand; Fontaine, Gaëlle; Duquesne, Sophie; Försth, Michael; Bourbigot, Serge

2015-11-20

The pyrolysis of solid polymeric materials is a complex process that involves both chemical and physical phenomena such as phase transitions, chemical reactions, heat transfer, and mass transport of gaseous components. For modeling purposes, it is important to characterize and to quantify the properties driving those phenomena, especially in the case of flame-retarded materials. In this study, protocols have been developed to characterize the thermal conductivity and the heat capacity of an ethylene-vinyl acetate copolymer (EVA) flame retarded with aluminum tri-hydroxide (ATH). These properties were measured for the various species identified across the decomposition of the material. Namely, the thermal conductivity was found to decrease as a function of temperature before decomposition whereas the ceramic residue obtained after the decomposition at the steady state exhibits a thermal conductivity as low as 0.2 W/m/K. The heat capacity of the material was also investigated using both isothermal modulated Differential Scanning Calorimetry (DSC) and the standard method (ASTM E1269). It was shown that the final residue exhibits a similar behavior to alumina, which is consistent with the decomposition pathway of EVA/ATH. Besides, the two experimental approaches give similar results over the whole range of temperatures. Moreover, the optical properties before decomposition and the heat capacity of the decomposition gases were also analyzed. Those properties were then used as input data for a pyrolysis model in order to predict gasification experiments. Mass losses of gasification experiments were well predicted, thus validating the characterization of the thermo-physical properties of the material.

Physical Stress Echocardiography: Prediction of Mortality and Cardiac Events in Patients with Exercise Test showing Ischemia

Directory of Open Access Journals (Sweden)

Ana Carla Pereira de Araujo

2014-11-01

Full Text Available Background: Studies have demonstrated the diagnostic accuracy and prognostic value of physical stress echocardiography in coronary artery disease. However, the prediction of mortality and major cardiac events in patients with exercise test positive for myocardial ischemia is limited. Objective: To evaluate the effectiveness of physical stress echocardiography in the prediction of mortality and major cardiac events in patients with exercise test positive for myocardial ischemia. Methods: This is a retrospective cohort in which 866 consecutive patients with exercise test positive for myocardial ischemia, and who underwent physical stress echocardiography were studied. Patients were divided into two groups: with physical stress echocardiography negative (G1 or positive (G2 for myocardial ischemia. The endpoints analyzed were all-cause mortality and major cardiac events, defined as cardiac death and non-fatal acute myocardial infarction. Results: G2 comprised 205 patients (23.7%. During the mean 85.6 ± 15.0-month follow-up, there were 26 deaths, of which six were cardiac deaths, and 25 non-fatal myocardial infarction cases. The independent predictors of mortality were: age, diabetes mellitus, and positive physical stress echocardiography (hazard ratio: 2.69; 95% confidence interval: 1.20 - 6.01; p = 0.016. The independent predictors of major cardiac events were: age, previous coronary artery disease, positive physical stress echocardiography (hazard ratio: 2.75; 95% confidence interval: 1.15 - 6.53; p = 0.022 and absence of a 10% increase in ejection fraction. All-cause mortality and the incidence of major cardiac events were significantly higher in G2 (p < 0. 001 and p = 0.001, respectively. Conclusion: Physical stress echocardiography provides additional prognostic information in patients with exercise test positive for myocardial ischemia.

Development of Models to Simulate Tracer Tests for Characterization of Enhanced Geothermal Systems

Energy Technology Data Exchange (ETDEWEB)

Williams, Mark D.; Reimus, Paul; Vermeul, Vincent R.; Rose, Peter; Dean, Cynthia A.; Watson, Tom B.; Newell, D.; Leecaster, Kevin; Brauser, Eric

2013-05-01

A recent report found that power and heat produced from enhanced (or engineered) geothermal systems (EGSs) could have a major impact on the U.S energy production capability while having a minimal impact on the environment. EGS resources differ from high-grade hydrothermal resources in that they lack sufficient temperature distribution, permeability/porosity, fluid saturation, or recharge of reservoir fluids. Therefore, quantitative characterization of temperature distributions and the surface area available for heat transfer in EGS is necessary for the design and commercial development of the geothermal energy of a potential EGS site. The goal of this project is to provide integrated tracer and tracer interpretation tools to facilitate this characterization. This project was initially focused on tracer development with the application of perfluorinated tracer (PFT) compounds, non-reactive tracers used in numerous applications from atmospheric transport to underground leak detection, to geothermal systems, and evaluation of encapsulated PFTs that would release tracers at targeted reservoir temperatures. After the 2011 midyear review and subsequent discussions with the U.S. Department of Energy Geothermal Technology Program (GTP), emphasis was shifted to interpretive tool development, testing, and validation. Subsurface modeling capabilities are an important component of this project for both the design of suitable tracers and the interpretation of data from in situ tracer tests, be they single- or multi-well tests. The purpose of this report is to describe the results of the tracer and model development for simulating and conducting tracer tests for characterizing EGS parameters.

Physical and chemical characteristics of fibrous peat

Science.gov (United States)

Sutejo, Yulindasari; Saggaff, Anis; Rahayu, Wiwik; Hanafiah

2017-11-01

Banyuasin is one of the regency in South Sumatera which has an area of 200.000 Ha of peat land. Peat soil are characterized by high compressibility parameters and low initial shear strength. Block sampling method was used to obtain undisturbed sample. The results of this paper describe the characteristics of peat soil from physical and chemical testing. The physical and chemical characteristics of peat include water content (ω), specific gravity (Gs), Acidity (pH), unit weight (γ), and ignition loss tests. SEM and EDS test was done to determine the differences in fiber content and to analyze chemical elements of the specimen. The average results ω, Gs, and pH are 263.538 %, 1.847, and 3.353. Peat is classified in H4 (by Von Post). The results of organic content (OC), ash content (AC), and fiber content (FC) are found 78.693 %, 21.310 %, and 73.703 %. From the results of physical and chemical tests, the peat in Banyuasin is classified as fibrous peat. All the results of the characteristics and classification of fibrous peat compared with published data were close.

Test plan for prototype dielectric permittivity sensor

International Nuclear Information System (INIS)

Pfeifer, M.C.

1993-07-01

The digface characterization project funded by the Buried Waste Integrated Demonstration (BWID) is designed to test a new method of monitoring hazardous conditions during the remediation at waste sites. Often on a large scale, the exact cause of each anomaly is difficult to determine and ambiguities remain in the characterization of a site. The digface characterization concept is designed to alleviate some of this uncertainty by creating systems that monitor small volumes of soil and detect anomalous areas during remediation before they are encountered. The goal of the digface characterization demonstration is to detect changes in the physical properties from one volume to another and relate these changes in physical properties to changes in the level of contamination. Dielectric permittivity mapping is a method that might prove useful in digface characterization. In this project, the role of a dielectric permittivity monitoring device is under investigation. This project addresses two issues: what are the optimal means of mapping dielectric permittivity contrasts and what types of targets can be detected using dielectric permittivity mapping

A Study of the Physical Fitness Test in Relation to Demographics, Academic Achievement, and Students' Physical Fitness Perceptions

Science.gov (United States)

Mobilia-Jones, Karen

2010-01-01

This study examines the overall results of the Physical Fitness Test (PFT) and the six fitness areas of the PFT, academic achievement, demographics and self perceptions and the potential impact on students' performance on the PFT. While academic expectations are increasing, the adolescent obesity rate is also increasing, producing a decline in the…

K-Basin spent nuclear fuel characterization data report 2

International Nuclear Information System (INIS)

Abrefah, J.; Gray, W.J.; Ketner, G.L.; Marschman, S.C.; Pyecha, T.D.; Thornton, T.A.

1996-03-01

An Integrated Process Strategy has been developed to package, condition, transport, and store in an interim storage facility the spent nuclear fuel (SNF) currently residing in the K-Basins at Hanford. Information required to support the development of the condition process and to support the safety analyses must be obtained from characterization testing activities conducted on fuel samples from the Basins. Some of the information obtained in the testing was reported in PNL-10778, K-Basin Spent Nuclear Fuel Characterization Data Report (Abrefah et al. 1995). That report focused on the physical, dimensional, metallographic examinations of the first K-West (KW) Basin SNF element to be examined in the Postirradiation Testing Laboratory (PTL) hot cells; it also described some of the initial SNF conditioning tests. This second of the series of data reports covers the subsequent series of SNF tests on the first fuel element. These tests included optical microscopy analyses, conditioning (drying and oxidation) tests, ignition tests, and hydrogen content tests

K-Basin spent nuclear fuel characterization data report 2

Energy Technology Data Exchange (ETDEWEB)

Abrefah, J.; Gray, W.J.; Ketner, G.L.; Marschman, S.C.; Pyecha, T.D.; Thornton, T.A.

1996-03-01

An Integrated Process Strategy has been developed to package, condition, transport, and store in an interim storage facility the spent nuclear fuel (SNF) currently residing in the K-Basins at Hanford. Information required to support the development of the condition process and to support the safety analyses must be obtained from characterization testing activities conducted on fuel samples from the Basins. Some of the information obtained in the testing was reported in PNL-10778, K-Basin Spent Nuclear Fuel Characterization Data Report (Abrefah et al. 1995). That report focused on the physical, dimensional, metallographic examinations of the first K-West (KW) Basin SNF element to be examined in the Postirradiation Testing Laboratory (PTL) hot cells; it also described some of the initial SNF conditioning tests. This second of the series of data reports covers the subsequent series of SNF tests on the first fuel element. These tests included optical microscopy analyses, conditioning (drying and oxidation) tests, ignition tests, and hydrogen content tests.

Large-scale in situ heater tests for hydrothermal characterization at Yucca Mountain

International Nuclear Information System (INIS)

Buscheck, T.A.; Wilder, D.G.; Nitao, J.J.

1993-01-01

To safely and permanently store high-level nuclear-waste, the potential Yucca Mountain repository site must mitigate the release and transport of radionuclides for tens of thousands of years. In the failure scenario of greatest concern, water would contact a waste package, accelerate its failure rate, and eventually transport radionuclides to the water table. Our analysis indicate that the ambient hydrological system will be dominated by repository-heat-driven hydrothermal flow for tens of thousands of years. In situ heater tests are required to provide an understanding of coupled geomechanical-hydrothermal-geochemical behavior in the engineered and natural barriers under repository thermal loading conditions. In situ heater tests have been included in the Site Characterization Plan in response to regulatory requirements for site characterization and to support the validation of process models required to assess the total systems performance at the site. The success of the License Application (LA) hinges largely on how effectively we validate the process models that provide the basis for performance assessment. Because of limited time, some of the in situ tests will have to be accelerated relative to actual thermal loading conditions. We examine the trade-offs between the limited test duration and generating hydrothermal conditions applicable to repository performance during the entire thermal loading cycle, including heating (boiling and dry-out) and cooldown (re-wetting). For in situ heater tests duration of 6-7 yr (including 4 yr of full-power heating) is required. The parallel use of highly accelerated, shorter-duration tests may provide timely information for the LA, provided that the applicability of the test results can be validated against ongoing nominal-rate heater tests

X ray reflection masks: Manufacturing, characterization and first tests

Science.gov (United States)

Rahn, Stephen

1992-09-01

SXPL (Soft X-ray Projection Lithography) multilayer mirrors are characterized, laterally structured and then used as reflection masks in a projecting lithography procedure. Mo/Si-multilayer mirrors with a 2d in the region of 14 nm were characterized by Cu-k(alpha) grazing incidence as well as soft X-ray normal incidence reflectivity measurements. The multilayer mirrors were patterned by reactive ion etching with CF4 using a photoresist as etch mask, thus producing X-ray reflection masks. The masks were tested at the synchrotron radiation laboratory of the electron accelerator ELSA. A double crystal X-ray monochromator was modified so as to allow about 0.5 sq cm of the reflection mask to be illuminated by white synchrotron radiation. The reflected patterns were projected (with an energy of 100 eV) onto a resist and structure sizes down to 8 micrometers were nicely reproduced. Smaller structures were distorted by Fresnel-diffraction. The theoretically calculated diffraction images agree very well with the observed images.

In-situ load-deformation characterization of the CSM/OCRD jointed test block

International Nuclear Information System (INIS)

Richardson, A.M.; Hustrulid, W.; Brown, S.; Ubbes, W.

1985-01-01

An extensive ambient-temperature test series has recently been completed on a block of Precambrian Gneiss at the Colorado School of Mines (CSM) Experimental Mine in Idaho Springs, Colorado. Block tests came into existence out of a desire to test a relatively large volume of rock and thereby minimize the scaling problems encountered when laboratory test results are used to obtain modeling parameters for full-size structures. A typical block test involves isolation of a large, approximately two-meter cube of rock by cutting slots on four sides and inserting flatjacks for loading. Much interest has recently centered around block tests as a promising method for in-situ characterization of rock-masses for licensing future commercial nuclear-waste repositories in crystalline rock. To date only a few block tests have been conducted

Spatial characterization of Bessel-like beams for strong-field physics.

Science.gov (United States)

Summers, Adam M; Yu, Xiaoming; Wang, Xinya; Raoul, Maxime; Nelson, Josh; Todd, Daniel; Zigo, Stefan; Lei, Shuting; Trallero-Herrero, Carlos A

2017-02-06

We present a compact, simple design for the generation and tuning of both the spot size and effective focal length of Bessel-like beams. In particular, this setup provides an important tool for the use of Bessel-like beams with high-power, femtosecond laser systems. Using a shallow angle axicon in conjunction with a spherical lens, we show that it is possible to focus Bessel-like modes to comparable focal spot sizes to sharp axicons while maintaining a long effective focal length. The resulting focal profiles are characterized in detail using an accurate high dynamic range imaging technique. Quantitatively, we introduce a metric (R0.8) which defines the spot-size containing 80% of the total energy. Our setup overcomes the typical compromise between long working distances and small spot sizes. This is particularly relevant for strong-field physics where most experiments must operate in vacuum.

Hanford Waste Physical and Rheological Properties: Data and Gaps - 12078

Energy Technology Data Exchange (ETDEWEB)

Kurath, D.E.; Wells, B.E.; Huckaby, J.L.; Mahoney, L.A.; Daniel, R.C.; Burns, C.A.; Tingey, J.M.; Cooley, S.K. [Pacific Northwest National Laboratory PO Box 999, Richland WA 99352 (United States)

2012-07-01

The retrieval, transport, treatment and disposal operations associated with Hanford Tank Wastes involve the handling of a wide range of slurries. Knowledge of the physical and rheological properties of the waste is a key component to the success of the design and implementation of the waste processing facilities. Previous efforts to compile and analyze the physical and rheological properties were updated with new results including information on solids composition and density, particle size distributions, slurry rheology, and particle settling behavior. The primary source of additional data is from a recent series of tests sponsored by the Hanford Waste Treatment and Immobilization Plant (WTP). These tests involved an extensive suite of characterization and bench-scale process testing of 8 waste groups representing approximately 75% of the high-level waste mass expected to be processed through the WTP. Additional information on the morphology of the waste solids was also included. Based on the updated results, a gap analysis to identify gaps in characterization data, analytical methods and data interpretation was completed. (authors)

Physical-mechanical characterization of hydroxyapatite-titanium oxide composites made by the polymeric sponge method

International Nuclear Information System (INIS)

Galdino, A.G.S.; Zavaglia, C.A.C.

2011-01-01

Bioceramics have been used as bone reconstruction materials since last decades, where hydroxyapatite is one of the most used for this purpose. However, hydroxyapatite's mechanical strength is not so high when compared to other bioceramics. This work aimed on characterizing physically and mechanically composites of HA-TiO_2. Samples were made by the polymeric sponge method with 70% - 30% wt., 60% - 40% wt. and 50% - 50% wt. of HA - TiO_2, calcined at 550 deg C for sponge burning and sintered at 1250 deg C, 1300 deg C and 1350 deg C. Samples were submitted to mechanical essays of compression and Hardness Vickers and to physical essays of water absorption, apparent density, burning linear retraction and apparent density. Results showed relatively better than those of pure hydroxyapatite and they are in accordance with the literature. (author)

OARSI recommended performance-based tests to assess physical function in people diagnosed with hip or knee osteoarthritis

DEFF Research Database (Denmark)

Dobson, F; Hinman, R S; Roos, Ewa M.

2013-01-01

To recommend a consensus-derived set of performance-based tests of physical function for use in people diagnosed with hip or knee osteoarthritis (OA) or following joint replacement.......To recommend a consensus-derived set of performance-based tests of physical function for use in people diagnosed with hip or knee osteoarthritis (OA) or following joint replacement....

Development of a versatile readout and test system and characterization of a capacitively coupled active pixel sensor

Energy Technology Data Exchange (ETDEWEB)

Janssen, Jens; Gonella, Laura; Hemperek, Tomasz; Hirono, Toko; Huegging, Fabian; Krueger, Hans; Wermes, Norbert [Institute of Physics, University of Bonn, Bonn (Germany); Peric, Ivan [Karlsruher Institut fuer Technologie, Karlsruhe (Germany); Collaboration: ATLAS-Collaboration

2015-07-01

With the availability of high voltage and high resistivity CMOS processes, active pixel sensors are becoming increasingly interesting for radiation detection in high energy physics experiments. Although the pixel signal-to-noise ratio and the sensor radiation tolerance were improved, active pixel sensors cannot yet compete with state-of-the-art hybrid pixel detector in a high radiation environment. Hence, active pixel sensors are possible candidates for the outer tracking detector in HEP experiments where production cost plays a role. The investigation of numerous prototyping steps and different technologies is still ongoing and requires a versatile test and readout system, which will be presented in this talk. A capacitively coupled active pixel sensor fabricated in AMS 180 nm high voltage CMOS process is investigated. The sensor is designed to be glued to existing front-end pixel readout chips. Results from the characterization are presented in this talk.

Screening for physical inactivity among adults: the value of distance walked in the six-minute walk test. A cross-sectional diagnostic study.

Science.gov (United States)

Sperandio, Evandro Fornias; Arantes, Rodolfo Leite; da Silva, Rodrigo Pereira; Matheus, Agatha Caveda; Lauria, Vinícius Tonon; Bianchim, Mayara Silveira; Romiti, Marcello; Gagliardi, Antônio Ricardo de Toledo; Dourado, Victor Zuniga

2016-01-01

Accelerometry provides objective measurement of physical activity levels, but is unfeasible in clinical practice. Thus, we aimed to identify physical fitness tests capable of predicting physical inactivity among adults. Diagnostic test study developed at a university laboratory and a diagnostic clinic. 188 asymptomatic subjects underwent assessment of physical activity levels through accelerometry, ergospirometry on treadmill, body composition from bioelectrical impedance, isokinetic muscle function, postural balance on a force platform and six-minute walk test. We conducted descriptive analysis and multiple logistic regression including age, sex, oxygen uptake, body fat, center of pressure, quadriceps peak torque, distance covered in six-minute walk test and steps/day in the model, as predictors of physical inactivity. We also determined sensitivity (S), specificity (Sp) and area under the curve of the main predictors by means of receiver operating characteristic curves. The prevalence of physical inactivity was 14%. The mean number of steps/day (≤ 5357) was the best predictor of physical inactivity (S = 99%; Sp = 82%). The best physical fitness test was a distance in the six-minute walk test and ≤ 96% of predicted values (S = 70%; Sp = 80%). Body fat > 25% was also significant (S = 83%; Sp = 51%). After logistic regression, steps/day and distance in the six-minute walk test remained predictors of physical inactivity. The six-minute walk test should be included in epidemiological studies as a simple and cheap tool for screening for physical inactivity.

Site characterization and monitoring data from Area 5 Pilot Wells, Nevada Test Site, Nye County, Nevada

International Nuclear Information System (INIS)

1994-02-01

The Special Projects Section (SPS) of Reynolds Electrical ampersand Engineering Co., Inc. (REECO) is responsible for characterizing the subsurface geology and hydrology of the Area 5 Radioactive Waste Management Site (RWMS) at the Nevada Test Site (NTS) for the US Department of Energy, Nevada Operations Office (DOE/NV), Environmental Restoration and Waste Management Division, Waste Operations Branch. The three Pilot Wells that comprise the Pilot Well Project are an important part of the Area 5 Site Characterization Program designed to determine the suitability of the Area 5 RWMS for disposal of low-level waste (LLW), mixed waste (MW), and transuranic waste (TRU). The primary purpose of the Pilot Well Project is two-fold: first, to characterize important water quality and hydrologic properties of the uppermost aquifer; and second, to characterize the lithologic, stratigraphic, and hydrologic conditions which influence infiltration, redistribution, and percolation, and chemical transport through the thick vadose zone in the vicinity of the Area 5 RWMS. This report describes Pilot Well drilling and coring, geophysical logging, instrumentation and stemming, laboratory testing, and in situ testing and monitoring activities

Chemical Characterization and Reactivity Testing of Fuel-Oxidizer Reaction Product (Test Report)

Science.gov (United States)

1996-01-01

The product of incomplete reaction of monomethylhydrazine (MMH) and nitrogen tetroxide (NTO) propellants, or fuel-oxidizer reaction product (FORP), has been hypothesized as a contributory cause of an anomaly which occurred in the chamber pressure (PC) transducer tube on the Reaction Control Subsystem (RCS) aft thruster 467 on flight STS-51. A small hole was found in the titanium-alloy PC tube at the first bend below the pressure transducer. It was surmised that the hole may have been caused by heat and pressure resulting from ignition of FORP. The NASA Johnson Space Center (JSC) White Sands Test Facility (WSTF) was requested to define the chemical characteristics of FORP, characterize its reactivity, and simulate the events in a controlled environment which may have lead to the Pc-tube failure. Samples of FORP were obtained from the gas-phase reaction of MMH with NTO under laboratory conditions, the pulsed firings of RCS thrusters with modified PC tubes using varied oxidizer or fuel lead times, and the nominal RCS thruster firings at WSTF and Kaiser-Marquardt. Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), accelerating rate calorimetry (ARC), ion chromatography (IC), inductively coupled plasma (ICP) spectrometry, thermogravimetric analysis (TGA) coupled to FTIR (TGA/FTIR), and mechanical impact testing were used to qualitatively and quantitatively characterize the chemical, thermal, and ignition properties of FORP. These studies showed that the composition of FORP is variable but falls within a limited range of compositions that depends on the fuel loxidizer ratio at the time of formation, composition of the post-formation atmosphere (reducing or oxidizing), and reaction or postreaction temperature. A typical composition contains methylhydrazinium nitrate (MMHN), ammonium nitrate (AN), methylammonium nitrate (MAN), and trace amounts of hydrazinium nitrate and 1,1-dimethylhydrazinium nitrate. The thermal decomposition

Physical quality control and nondestructive testing in industry

International Nuclear Information System (INIS)

Akay, K. S.; Avinc, A.

2000-01-01

The applications of Total Quality Management which now constitute the main factor of production and industrial life, are becoming widespread each day. This study evaluates the place, and the role of the physicist in the development and the application of measuring and central method, providing information on quality, environment and especially reliability, which is me of the most significant components of these concepts, acting as a guide and known, as Nondestructive Testing Methods in technology. Basic physical principles of the techniques, employed in practical applications as well as research and development stages of different fields requiring advanced technology, are presented and their advantages and disadvantages in usage are demonstrated in a comparative way. (authors)

Special physical examination tests for superior labrum anterior-posterior shoulder tears: an examination of clinical usefulness.

Science.gov (United States)

Sandrey, Michelle A

2013-01-01

Calvert E, Chambers GK, Regan W, Hawkins RH, Leith JM. Special physical examination tests for superior labrum anterior-posterior shoulder injuries are clinically limited and invalid: a diagnostic systematic review. J Clin Epidemiol. 2009;62(5):558-563. The systematic review focused on diagnostic accuracy studies to determine if evidence was sufficient to support the use of superior labrum anterior-posterior (SLAP) physical examination tests as valid and reliable. The primary question was whether there was sufficient evidence in the published literature to support the use of SLAP physical examination tests as valid and reliable diagnostic test procedures. Studies published in English were identified through database searches on MEDLINE, EMBASE, and the Cochrane database (1970-2004) using the search term SLAP lesions. The medical subject headings of arthroscopy, shoulder joint, and athletic injuries were combined with test or testing, physical examination, and sensitivity and specificity to locate additional sources. Other sources were identified by rereviewing the reference lists of included studies and review articles. Studies were eligible based on the following criteria: (1) published in English, (2) focused on the physical examination of SLAP lesions, and (3) presented original data. A study was excluded if the article was limited to a clinical description of 1 or more special tests without any research focus to provide clinical accuracy data or if it did not focus on the topic. The abstracts that were located through the search strategies were reviewed, and potentially relevant abstracts were selected. Strict epidemiologic methods were used to obtain and collate all relevant studies; the authors developed a study questionnaire to record study name, year of publication, study design, sample size, and statistics. Validity of the diagnostic test study was determined by applying the 5 criteria proposed by Calvert et al. If the study met the inclusion and validity

Comparing and characterizing transient and steady-state tests of the peripheral chemoreflex in humans.

Science.gov (United States)

Pfoh, Jamie R; Tymko, Michael M; Abrosimova, Maria; Boulet, Lindsey M; Foster, Glen E; Bain, Anthony R; Ainslie, Philip N; Steinback, Craig D; Bruce, Christina D; Day, Trevor A

2016-03-01

What is the central question of this study? We aimed to characterize the cardiorespiratory and cerebrovascular responses to transient and steady-state tests of the peripheral chemoreflex and to compare the hypoxic ventilatory responses (HVRs) between these tests. What is the main finding and its importance? The cardiovascular and cerebrovascular responses to transient tests were small in magnitude and short in duration. The steady-state isocapnic hypoxia test elicited a larger HVR than the transient 100% N(2) test, but the response magnitudes were correlated within individuals. The transient test of the HVR elicits fewer systemic effects than steady-state techniques and may have greater experimental utility than previously appreciated. Carotid chemoreceptors detect changes in arterial PO(2) and PCO(2), eliciting a peripheral chemoreflex (PCR). Steady-state (SS) hypoxia tests using dynamic end-tidal forcing (DEF) have been used to assess the hypoxic ventilatory response (HVR) but may be confounded by concomitant systemic effects. Transient tests of the PCR have also been developed but are not widely used, nor have the cardiovascular and cerebrovascular responses been characterized. We characterized the cardiorespiratory and cerebrovascular responses to transient tests of the PCR and compared the HVR between transient and SS-DEF tests. We hypothesized that the cardiovascular and cerebrovascular responses to the transient tests would be minimal and that the respiratory responses elicited from the transient and SS-DEF tests would be different in magnitude and not well correlated within individuals. Participants underwent five consecutive trials of two transient tests [three-breath 100% N(2) (TT-N(2)) and a single-breath 13% CO(2), in air] and two 10 min SS-DEF tests [isocapnic (SS-ISO) and poikilocapnic (SS-POI) hypoxia]. In response to the transient tests, heart rate, mean arterial pressure and the middle and posterior cerebral artery blood velocity increased (all P

Standardization of Nanoparticle Characterization: Methods for Testing Properties, Stability, and Functionality of Edible Nanoparticles.

Science.gov (United States)

McClements, Jake; McClements, David Julian

2016-06-10

There has been a rapid increase in the fabrication of various kinds of edible nanoparticles for oral delivery of bioactive agents, such as those constructed from proteins, carbohydrates, lipids, and/or minerals. It is currently difficult to compare the relative advantages and disadvantages of different kinds of nanoparticle-based delivery systems because researchers use different analytical instruments and protocols to characterize them. In this paper, we briefly review the various analytical methods available for characterizing the properties of edible nanoparticles, such as composition, morphology, size, charge, physical state, and stability. This information is then used to propose a number of standardized protocols for characterizing nanoparticle properties, for evaluating their stability to environmental stresses, and for predicting their biological fate. Implementation of these protocols would facilitate comparison of the performance of nanoparticles under standardized conditions, which would facilitate the rational selection of nanoparticle-based delivery systems for different applications in the food, health care, and pharmaceutical industries.

A standardization of the physical tests for external irradiation measuring detectors

International Nuclear Information System (INIS)

1977-05-01

This report is the result of a standardization work, realized within the Radioprotection Services of the A.E.C., of the physical tests for dectors measuring external irradiations. Among the various tests mentionned, calibration and the establishment of the relative spectral response are treated in details. As far as calibration is concerned, the standardization refers to: the reference detector, the reference radiation source, the installation and calibration procedure. As for the relative spectral response the standardization refers to: the reference detector, the radiation sources to be used. High flux detectors and those for pulse electromagnetic radiations are also dealt with [fr

An experimental test of control theory-based interventions for physical activity.

Science.gov (United States)

Prestwich, Andrew; Conner, Mark; Hurling, Robert; Ayres, Karen; Morris, Ben

2016-11-01

To provide an experimental test of control theory to promote physical activity. Parallel groups, simple randomized design with an equal chance of allocation to any group. Participants not meeting recommended levels of physical activity but physically safe to do so (N = 124) were recruited on a UK university campus and randomized to goal-setting + self-monitoring + feedback (GS + SM + F, n = 40), goal-setting + self-monitoring (GS + SM, n = 40), or goal-setting only (GS, n = 44) conditions that differentially tapped the key features of control theory. Accelerometers assessed physical activity (primary outcome) as well as self-report over a 7-day period directly before/after the start of the intervention. The participants in the GS + SM + F condition significantly outperformed those in the GS condition, d = 0.62, 95% CI d = 0.15-1.08, and marginally outperformed those in the GS + SM condition in terms of total physical activity at follow-up on the accelerometer measure, d = 0.33, 95% CI d = -0.13 to 0.78. The feedback manipulation (GS + SM + F vs. GS + SM and GS) was most effective when baseline intentions were weak. These patterns did not emerge on the self-report measure but, on the basis of this measure, the feedback manipulation increased the risk that participants coasted in relation to their goal in the first few days of the intervention period. Using behaviour change techniques consistent with control theory can lead to significant short-term improvements on objectively assessed physical activity. Further research is needed to examine the underlying theoretical principles of the model. Statement of contribution What is already known on this subject? Interventions incorporating more techniques that are consistent with control theory are associated with larger positive changes in health behaviours and related outcomes (see reviews by Dombrowski et al., ; Michie et al., ). However, none of the studies included in these

Nuclear start-up, testing and core management of the Fast Test Reactor (FTR)

International Nuclear Information System (INIS)

Bennett, R.A.; Daughtry, J.W.; Harris, R.A.; Jones, D.H.; Nelson, J.V.; Rawlins, J.A.; Rothrock, R.B.; Sevenich, R.A.; Zimmerman, B.D.

1980-01-01

Plans for the nuclear start-up, low and high power physics testing, and core management of the Fast Test Reactor (FTR) are described. Owing to the arrangement of the fuel-handling system, which permits continuous instrument lead access to experiments during refuelling, it is most efficient to load the reactor in an asymmetric fashion, filling one-third core sectors at a time. The core neutron level will be monitored during this process using both in-core and ex-core detectors. A variety of physics tests are planned following the core loading. Because of the experimental purpose of the reactor, these tests will include a comprehensive characterization programme involving both active and passive neutron and gamma measurements. Following start-up tests, the FTR will be operated as a fast neutron irradiation facility, to test a wide variety of fast reactor core components and materials. Nuclear analyses will be made prior to each irradiation cycle to confirm that the planned arrangement of standard and experimental components satisfies all safety and operational constraints, and that all experiments are located so as to achieve their desired irradiation environment. (author)

Screening for physical inactivity among adults: the value of distance walked in the six-minute walk test. A cross-sectional diagnostic study

Directory of Open Access Journals (Sweden)

Evandro Fornias Sperandio

Full Text Available ABSTRACT: CONTEXT AND OBJECTIVES: Accelerometry provides objective measurement of physical activity levels, but is unfeasible in clinical practice. Thus, we aimed to identify physical fitness tests capable of predicting physical inactivity among adults. DESIGN AND SETTING: Diagnostic test study developed at a university laboratory and a diagnostic clinic. METHODS: 188 asymptomatic subjects underwent assessment of physical activity levels through accelerometry, ergospirometry on treadmill, body composition from bioelectrical impedance, isokinetic muscle function, postural balance on a force platform and six-minute walk test. We conducted descriptive analysis and multiple logistic regression including age, sex, oxygen uptake, body fat, center of pressure, quadriceps peak torque, distance covered in six-minute walk test and steps/day in the model, as predictors of physical inactivity. We also determined sensitivity (S, specificity (Sp and area under the curve of the main predictors by means of receiver operating characteristic curves. RESULTS: The prevalence of physical inactivity was 14%. The mean number of steps/day (≤ 5357 was the best predictor of physical inactivity (S = 99%; Sp = 82%. The best physical fitness test was a distance in the six-minute walk test and ≤ 96% of predicted values (S = 70%; Sp = 80%. Body fat > 25% was also significant (S = 83%; Sp = 51%. After logistic regression, steps/day and distance in the six-minute walk test remained predictors of physical inactivity. CONCLUSION: The six-minute walk test should be included in epidemiological studies as a simple and cheap tool for screening for physical inactivity.

CHARACTERIZATION OF SCHOOL ATTENDANCE OF STUDENTS WITH PHYSICAL DISABILITIES IN A CITY OF SÃO PAULO STATE

Directory of Open Access Journals (Sweden)

Adriana Garcia Gonçalves

2016-12-01

Full Text Available The study aimed to characterize the educational services offered to students with physical disabilities in a Municipal Education of a midsize city of São Paulo state. We gathered the data through document analysis and application of semi-structured interviews. We recorded the data on audio, transcribed and analyzed them. We categorized them into two categories, the first of which referred to the attendance policies and second, the organization of care for students with physical disabilities. The results showed that the system investigated showed accessibility policies supporting the use of assistive technology for students with disabilities enrolled in regular education, despite not indicate the need for specialized educational services when the student has no associated cognitive impairment. We concluded that there are myriad factors to contemplate the school inclusion of students with physical disabilities and that many actions are needed to ensure education and social participation of this target audience. Keywords: Special Education. Physical Disabilities. Specialized Educational Services. Assistive Technology.

The test of data driven TDC application in high energy physics experiment

International Nuclear Information System (INIS)

Liu Shubin; Guo Jianhua; Zhang Yanli; Zhao Long; An Qi

2006-01-01

In the high energy physics domain there is a trend to use integrated, high resolution, multi-hit time-digital-converter for time measurement, of which the data driven TDC is an important direction. Study on the method of how to test high performance TDC's characters and how to improve these characters will help us to select the proper TDC. The authors have studied the testing of a new high resolution TDC, which is planned to use in the third modification project of Beijing Spectrometer (BESIII). This paper introduces the test platform we built for the TDC, and the method by which we tested for nonlinearity, resolution, double pulse resolution characters, etc. The paper also gives the test results and introduces the compensation way to achieve a very high resolution (24.4 ps). (authors)

A Physical Protection Systems Test Bed for International Counter-Trafficking System Development

International Nuclear Information System (INIS)

Stinson, Brad J.; Kuhn, Michael J.; Donaldson, Terrence L.; Richardson, Dave; Rowe, Nathan C.; Younkin, James R.; Pickett, Chris A.

2011-01-01

Physical protection systems have a widespread impact on the nuclear industry in areas such as nuclear safeguards, arms control, and trafficking of illicit goods (e.g., nuclear materials) across international borders around the world. Many challenges must be overcome in design and deployment of foreign border security systems such as lack of infrastructure, extreme environmental conditions, limited knowledge of terrain, insider threats, and occasional cultural resistance. Successful security systems, whether it be a system designed to secure a single facility or a whole border security system, rely on the entire integrated system composed of multiple subsystems. This test bed is composed of many unique sensors and subsystems, including wireless unattended ground sensors, a buried fiber-optic acoustic sensor, a lossy coaxial distributed sensor, wireless links, pan-tilt-zoom cameras, mobile power generation systems, unmanned aerial vehicles, and fiber-optic-fence intrusion detection systems. A Common Operating Picture software architecture is utilized to integrate a number of these subsystems. We are currently performance testing each system for border security and perimeter security applications by examining metrics such as probability of sense and a qualitative understanding of the sensors vulnerability of defeat. The testing process includes different soil conditions for buried sensors (e.g., dry, wet, and frozen) and an array of different tests including walking, running, stealth detection, and vehicle detection. Also, long term sustainability of systems is tested including performance differences due to seasonal variations (e.g. summer versus winter, while raining, in foggy conditions). The capabilities of the test bed are discussed. Performance testing results, both at the individual component level and integrated into a larger system for a specific deployment (in situ), help illustrate the usefulness and need for integrated testing facilities to carry out this

Characterization for capillary barriers effects in a sand box test using time-lapsed GPR measurements

Science.gov (United States)

Kuroda, S.; Ishii, N.; Morii, T.

2017-12-01

Capillary barriers have been known as the method to protect subsurface regions against infiltration from soil surface. It is caused by essentially heterogeneous structure in permeability or soil physical property and produce non-uniform infiltration process then, in order to estimate the actual situation of the capillary barrier effect, the site-characterization with imaging technique like geophysical prospecting is effective. In this study, we examine the applicability of GPR to characterization for capillary barriers. We built a sand box with 90x340x90cm in which a thin high-permeable gravel layer was embedded as a capillary barrier. We conducted an infiltration test in the sand box using porous tube array for irrigation. It is expected to lead to non-uniform flow of soil water induced by capillary barrier effects. We monitored this process by various types of GPR measurements, including time-lapsed common offset profiling (COP) with multi- frequency antenna and transmission measurements like cross-borehole radar. At first, we conducted GPR common-offset survey. It could show the depth of capillary barrier in sand box. After that we conducted the infiltration test and GPR monitoring for infiltration process. GPR profiles can detect the wetting front and estimate water content change in the soil layer above the capillary barrier. From spatial change in these results we can estimate the effect of capillary barrier and the zone where the break through occur or not. Based on these results, we will discuss the applicability of GPR for monitoring the phenomena around the capillary barrier of soil. At first, we conducted GPR common-offset survey. It could show the depth of capillary barrier in sand box. After that we conducted the infiltration test and GPR monitoring for infiltration process. GPR profiles can detect the wetting front and estimate water content change in the soil layer above the capillary barrier. From spatial change in these results we can estimate the

Characterizations of additive manufactured porous titanium implants.

Science.gov (United States)

Basalah, Ahmad; Shanjani, Yaser; Esmaeili, Shahrzad; Toyserkani, Ehsan

2012-10-01

This article describes physical, chemical, and mechanical characterizations of porous titanium implants made by an additive manufacturing method to gain insight into the correlation of process parameters and final physical properties of implants used in orthopedics. For the manufacturing chain, the powder metallurgy technology was combined with the additive manufacturing to fabricate the porous structure from the pure tanium powder. A 3D printing machine was employed in this study to produce porous bar samples. A number of physical parameters such as titanium powder size, polyvinyl alcohol (PVA) amount, sintering temperature and time were investigated to control the mechanical properties and porosity of the structures. The produced samples were characterized through porosity and shrinkage measurements, mechanical compression test and scanning electron microscopy (SEM). The results showed a level of porosity in the samples in the range of 31-43%, which is within the range of the porosity of the cancelluous bone and approaches the range of the porosity of the cortical bone. The results of the mechanical test showed that the compressive strength is in the wide range of 56-509 MPa implying the effect of the process parameters on the mechanical strengths. This technique of manufacturing of Ti porous structures demonstrated a low level of shrinkage with the shrinkage percentage ranging from 1.5 to 5%. Copyright © 2012 Wiley Periodicals, Inc.

Characterization of physical properties of Al2O3 and ZrO2 nanofluids for heat transfer applications

International Nuclear Information System (INIS)

Rocha, Marcelo S.; Cabral, Eduardo L.L.; Sabundjian, Gaiane; Yoriyaz, Helio; Lima, Ana Cecilia S.; Belchior Junior, Antonio; Prado, Adelk C.; Filho, Tufic M.; Andrade, Delvonei A.; Shorto, Julian M.B.; Mesquita, Roberto N.; Otubo, Larissa; Baptista Filho, Benedito D.; Pinho, Priscila G.M.; Ribatsky, Gherhardt; Moraes, Anderson Antonio Ubices

2015-01-01

Studies demonstrate that nanofluids based on metal oxide nanoparticles have physical properties that characterize them as promising fluids, mainly, in industrial systems in which high heat flux takes place. Water based nanofluids of Al 2 O 3 and ZrO 2 were characterized regarding its promising use in heat transfer applications. Three different concentrations of dispersed solutions of cited nanofluids were prepared (0.01% vol., 0.05% vol., and 0.1% vol.) from commercial nanofluids. Experimental measurements were carried out at different temperatures. Thermal conductivity, viscosity and density of the prepared nanofluids were measured. (author)

Characterization test of the optimized H type grid spring under the in-grid boundary condition

International Nuclear Information System (INIS)

Yoon, Kyung Ho; Kim, Hyung Tae; Lee, Kang Hee; Kang, Heung Seok

2004-01-01

This paper is dealing with the simplified method for the characterization test. In reality, the spring should be tested with the test specimen of spacer grid assembly itself (assembly-based test). But the available space for loading is very small due to the dimples and the spring of the adjacent straps, much care should be necessary in conducting the assembly-based test. Test results are compared with the previous test results for checking the usability of the assembly-based test

Characterization of the Roman curse tablet

Science.gov (United States)

Liu, Wen; Zhang, Boyang; Fu, Lin

2017-08-01

The Roman curse tablet, produced in ancient Rome period, is a metal plate that inscribed with curses. In this research, several techniques were used to find out the physical structure and chemical composition of the Roman curse tablet, and testified the hypothesis that whether the tablet is made of pure lead or lead alloy. A sample of Roman Curse Tablet from the Johns Hopkins Archaeological Museum was analyzed using several different characterization techniques to determine the physical structure and chemical composition. The characterization techniques used were including optical microscopy, scanning electron microscopy (SEM), atomic force microscopy (AFM), and differential scanning calorimetry (DSC). Because of the small sample size, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and X-ray fluorescence (XRF) cannot test the sample. Results from optical microscopy and SEM, enlarged images of the sample surface were studied. The result revealed that the sample surface has a rough, non-uniform, and grainy surface. AFM provides three-dimensional topography of the sample surface, studying the sample surface in atomic level. DSC studies the thermal property, which is most likely a lead-alloy, not a pure lead. However, none of these tests indicated anything about the chemical composition. Future work will be required due to the lack of measures finding out its chemical composition. Therefore, from these characterization techniques above, the Roman curse tablet sample is consisted of lead alloy, not pure lead.

New test and characterization methods for PV modules and cells

Energy Technology Data Exchange (ETDEWEB)

Van Aken, B.; Sommeling, P. [ECN Solar Energy, Petten (Netherlands); Scholten, H. [Solland, Heerlen (Netherlands); Muller, J. [Moser-Baer, Eindhoven (Netherlands); Grossiord, N. [Holst Centre, Eindhoven (Netherlands); Smits, C.; Blanco Mantecon, M. [Holland Innovative, Eindhoven (Netherlands); Verheijen, M.; Van Berkum, J. [Philips Innovation Services, Eindhoven (Netherlands)

2012-08-15

The results of the project geZONd (shared facility for solar module analysis and reliability testing) are described. The project was set up by Philips, ECN, Holst, Solland, OM and T and Holland Innovative. The partners have shared most of their testing and analysis equipment for PV modules and cells, and together developed new or improved methods (including the necessary application know-how). This enables faster and more efficient innovation projects for each partner, and via commercial exploitation for other interested parties. The project has concentrated on five failure modes: corrosion, delamination, moisture ingress, UV irradiation, and mechanical bending. Test samples represented all main PV technologies: wafer based PV and rigid and flexible thin-film PV. Breakthroughs are in very early detection of corrosion, in quantitative characterization of adhesion, in-situ detection of humidity and oxygen inside modules, and ultra-fast screening of materials on UV stability.

Development of indirect ring tension test for fracture characterization of asphalt mixtures

Science.gov (United States)

Zeinali Siavashani, Alireza

Low temperature cracking is a major distress in asphalt pavements. Several test configurations have been introduced to characterize the fracture properties of hot mix (HMA); however, most are considered to be research tools due to the complexity of the test methods or equipment. This dissertation describes the development of the indirect ring tension (IRT) fracture test for HMA, which was designed to be an effective and user-friendly test that could be deployed at the Department of Transportation level. The primary advantages of this innovative and yet practical test include: relatively large fracture surface test zone, simplicity of the specimen geometry, widespread availability of the required test equipment, and ability to test laboratory compacted specimens as well as field cores. Numerical modeling was utilized to calibrate the stress intensity factor formula of the IRT fracture test for various specimen dimensions. The results of this extensive analysis were encapsulated in a single equation. To develop the test procedure, a laboratory study was conducted to determine the optimal test parameters for HMA material. An experimental plan was then developed to evaluate the capability of the test in capturing the variations in the mix properties, asphalt pavement density, asphalt material aging, and test temperature. Five plant-produced HMA mixtures were used in this extensive study, and the results revealed that the IRT fracture test is highly repeatable, and capable of capturing the variations in the fracture properties of HMA. Furthermore, an analytical model was developed based on the viscoelastic properties of HMA to estimate the maximum allowable crack size for the pavements in the experimental study. This analysis indicated that the low-temperature cracking potential of the asphalt mixtures is highly sensitive to the fracture toughness and brittleness of the HMA material. Additionally, the IRT fracture test data seemed to correlate well with the data from

In Situ Vitrification Engineering-Scale Test ES-INEL-4 Product Characterization Test Plan

International Nuclear Information System (INIS)

Weidner, J.R.; Stoots, P.R.

1990-06-01

In 1987, the Buried Waste Program (BWP) was established within EG ampersand G Idaho, Inc., the prime contractor at INEL. Following the Environmental Restoration guidelines of the Buried Waste Program, the In Situ Vitrification Program is participating in a Remedial Investigation/Feasibility Study (RI/FS) for permanent disposal of INEL waste, in compliance with the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). This study was requested and is being funded by the Office of Technology Development of the Idaho Operations Office of DOE (DOE-ID). As part of the RI/FS, an in situ vitrification (ISV) scoping study on the treatability of mixed low-level and mixed transuranic-contaminated waste is being performed to determine the applicability of ISV to remediation of waste at SDA. In examination of the ISV process for applicability to SDA waste, this In Situ Vitrification Engineering-Scale Test ES-INEL-4 Product Characterization Test Plan identifies the following: sampling and analysis strategy; sampling procedures; methods to conduct analyses; equipment; and procedures to ensure data quality. 8 refs., 2 tabs

The prognostic value of electrodiagnostic testing in patients with sciatica receiving physical therapy.

Science.gov (United States)

Savage, Nathan J; Fritz, Julie M; Kircher, John C; Thackeray, Anne

2015-03-01

To investigate the prognostic value of electrodiagnostic testing in patients with sciatica receiving physical therapy. Electrodiagnostic testing was performed on 38 patients with sciatica participating in a randomized trial comparing different physical therapy interventions. Patients were grouped and analyzed according to the presence or absence of radiculopathy based on electrodiagnostic testing. Longitudinal data analysis was conducted using multilevel growth modeling with ten waves of data collected from baseline through the treatment and post-treatment periods up to 6 months. The primary outcome measure was changes in low back pain-related disability assessed using the Roland and Morris disability questionnaire (RMDQ). Patients with radiculopathy (n = 19) had statistically significant and clinically meaningful improvements in RMDQ scores at every post-treatment follow-up occasion regardless of treatment received. The final multilevel growth model revealed improvements in RMDQ scores in patients with radiculopathy at the 6-week (-8.1, 95 % CI -12.6 to -2.6; P = 0.006) and 6-month (-4.1, 95 % CI -7.4 to -0.7; P = 0.020) follow-up occasions compared to patients without radiculopathy. Treatment group was not a significant predictive factor at any follow-up occasion. An interaction between electrodiagnostic status and time revealed faster weekly improvements in RMDQ scores in patients with radiculopathy at the 6-week (-0.72, 95 % CI -1.4 to -0.04; P = 0.040) through the 16-week (-0.30, 95 % CI, -0.57 to -0.04; P = 0.028) follow-up occasions compared to patients without radiculopathy. The presence of lumbosacral radiculopathy identified with electrodiagnostic testing is a favorable prognostic factor for recovery in low back pain-related disability regardless of physical therapy treatment received.

Preliminary analysis in a clayey mass aimed at ceramic blocks production: physical and mineralogical characteristics

International Nuclear Information System (INIS)

Silva, L.J.M.D. da; Apolonio, T.G.; Salviano, A.F.; Taveira, S.K.A.; Garcia, T.G.C.; Silva, J; Luna, P.A.; Macedo, R.S.

2016-01-01

The physical, chemical and mineralogical characterization of the clayey mass are important in determining its properties, allowing a better knowledge of the raw material used in the manufacture of ceramic products. This work aims to characterize the raw material used in the manufacture of ceramic sealing blocks in a ceramic industry. Thus, it was evaluated by laboratory tests the raw material used in the production of ceramic blocks in a ceramics industry in the region of Carnauba dos Dantas, RN. The methodology used in the tests is the same as the IPT, which consists in carrying out the plasticity testing, particle size, chemical analysis and X-ray diffraction. Results indicate that the sample studied by the physical and mineralogical characteristics, has the potential to be applied in the manufacture of red ceramic products for use in construction. (author)

Reliability of specific physical examination tests for the diagnosis of shoulder pathologies: a systematic review and meta-analysis.

Science.gov (United States)

Lange, Toni; Matthijs, Omer; Jain, Nitin B; Schmitt, Jochen; Lützner, Jörg; Kopkow, Christian

2017-03-01

Shoulder pain in the general population is common and to identify the aetiology of shoulder pain, history, motion and muscle testing, and physical examination tests are usually performed. The aim of this systematic review was to summarise and evaluate intrarater and inter-rater reliability of physical examination tests in the diagnosis of shoulder pathologies. A comprehensive systematic literature search was conducted using MEDLINE, EMBASE, Allied and Complementary Medicine Database (AMED) and Physiotherapy Evidence Database (PEDro) through 20 March 2015. Methodological quality was assessed using the Quality Appraisal of Reliability Studies (QAREL) tool by 2 independent reviewers. The search strategy revealed 3259 articles, of which 18 finally met the inclusion criteria. These studies evaluated the reliability of 62 test and test variations used for the specific physical examination tests for the diagnosis of shoulder pathologies. Methodological quality ranged from 2 to 7 positive criteria of the 11 items of the QAREL tool. This review identified a lack of high-quality studies evaluating inter-rater as well as intrarater reliability of specific physical examination tests for the diagnosis of shoulder pathologies. In addition, reliability measures differed between included studies hindering proper cross-study comparisons. PROSPERO CRD42014009018. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

IOTA (Integrable Optics Test Accelerator): facility and experimental beam physics program

Science.gov (United States)

Antipov, S.; Broemmelsiek, D.; Bruhwiler, D.; Edstrom, D.; Harms, E.; Lebedev, V.; Leibfritz, J.; Nagaitsev, S.; Park, C. S.; Piekarz, H.; Piot, P.; Prebys, E.; Romanov, A.; Ruan, J.; Sen, T.; Stancari, G.; Thangaraj, C.; Thurman-Keup, R.; Valishev, A.; Shiltsev, V.

2017-03-01

The Integrable Optics Test Accelerator (IOTA) is a storage ring for advanced beam physics research currently being built and commissioned at Fermilab. It will operate with protons and electrons using injectors with momenta of 70 and 150 MeV/c, respectively. The research program includes the study of nonlinear focusing integrable optical beam lattices based on special magnets and electron lenses, beam dynamics of space-charge effects and their compensation, optical stochastic cooling, and several other experiments. In this article, we present the design and main parameters of the facility, outline progress to date and provide the timeline of the construction, commissioning and research. The physical principles, design, and hardware implementation plans for the major IOTA experiments are also discussed.

IOTA (Integrable Optics Test Accelerator): Facility and experimental beam physics program

International Nuclear Information System (INIS)

Antipov, Sergei; Broemmelsiek, Daniel; Bruhwiler, David; Edstrom, Dean; Harms, Elvin

2017-01-01

The Integrable Optics Test Accelerator (IOTA) is a storage ring for advanced beam physics research currently being built and commissioned at Fermilab. It will operate with protons and electrons using injectors with momenta of 70 and 150 MeV/c, respectively. The research program includes the study of nonlinear focusing integrable optical beam lattices based on special magnets and electron lenses, beam dynamics of space-charge effects and their compensation, optical stochastic cooling, and several other experiments. In this article, we present the design and main parameters of the facility, outline progress to date and provide the timeline of the construction, commissioning and research. Finally, the physical principles, design, and hardware implementation plans for the major IOTA experiments are also discussed.

Characterization of Oribtal Debris via Hyper-Velocity Ground-Based Tests

Science.gov (United States)

Cowardin, H.

2015-01-01

Existing DoD and NASA satellite breakup models are based on a key laboratory-based test, Satellite Orbital debris Characterization Impact Test (SOCIT), which has supported many applications and matched on-orbit events involving older satellite designs reasonably well over the years. In order to update and improve the break-up models and the NASA Size Estimation Model (SEM) for events involving more modern satellite designs, the NASA Orbital Debris Program Office has worked in collaboration with the University of Florida to replicate a hypervelocity impact using a satellite built with modern-day spacecraft materials and construction techniques. The spacecraft, called DebriSat, was intended to be a representative of modern LEO satellites and all major designs decisions were reviewed and approved by subject matter experts at Aerospace Corporation. DebriSat is composed of 7 major subsystems including attitude determination and control system (ADCS), command and data handling (C&DH), electrical power system (EPS), payload, propulsion, telemetry tracking and command (TT&C), and thermal management. To reduce cost, most components are emulated based on existing design of flight hardware and fabricated with the same materials. All fragments down to 2 mm is size will be characterized via material, size, shape, bulk density, and the associated data will be stored in a database for multiple users to access. Laboratory radar and optical measurements will be performed on a subset of fragments to provide a better understanding of the data products from orbital debris acquired from ground-based radars and telescopes. The resulting data analysis from DebriSat will be used to update break-up models and develop the first optical SEM in conjunction with updates into the current NASA SEM. The characterization of the fragmentation will be discussed in the subsequent presentation.

Current practices in corrosion, surface characterization, and nickel leach testing of cardiovascular metallic implants.

Science.gov (United States)

Nagaraja, Srinidhi; Di Prima, Matthew; Saylor, David; Takai, Erica

2017-08-01

In an effort to better understand current test practices and improve nonclinical testing of cardiovascular metallic implants, the Food and Drug Administration (FDA) held a public workshop on Cardiovascular Metallic Implants: corrosion, surface characterization, and nickel leaching. The following topics were discussed: (1) methods used for corrosion assessments, surface characterization techniques, and nickel leach testing of metallic cardiovascular implant devices, (2) the limitations of each of these in vitro tests in predicting in vivo performance, (3) the need, utility, and circumstances when each test should be considered, and (4) the potential testing paradigms, including acceptance criteria for each test. In addition to the above topics, best practices for these various tests were discussed, and knowledge gaps were identified. Prior to the workshop, discussants had the option to provide feedback and information on issues relating to each of the topics via a voluntary preworkshop assignment. During the workshop, the pooled responses were presented and a panel of experts discussed the results. This article summarizes the proceedings of this workshop and background information provided by workshop participants. Published 2016. This article is a U.S. Government work and is in the public domain in the USA. J Biomed Mater Res Part B: Appl Biomater, 105B: 1330-1341, 2017. Published 2016. This article is a U.S. Government work and is in the public domain in the USA.

A job-related fitness test for the Dutch police.

Science.gov (United States)

Strating, M; Bakker, R H; Dijkstra, G J; Lemmink, K A P M; Groothoff, J W

2010-06-01

The variety of tasks that characterize police work highlights the importance of being in good physical condition. To take a first step at standardizing the administration of a job-related test to assess a person's ability to perform the physical demands of the core tasks of police work. The principal research questions were: are test scores related to gender, age and function and are test scores related to body mass index (BMI) and the number of hours of physical exercise? Data of 6999 police officers, geographically spread over all parts of The Netherlands, who completed a physical competence test over a 1 year period were analysed. Women performed the test significantly more slowly than men. The mean test score was also related to age; the older a person the longer it took to complete the test. A higher BMI was associated with less hours of body exercise a week and a slower test performance, both in women and men. The differences in individual test scores, based on gender and age, have implications for future strategy within the police force. From a viewpoint of 'same job, same standard' one has to accept that test-score differences may lead to the exclusion of certain staff. However, from a viewpoint of 'diversity as a business issue', one may have to accept that on average, both female and older police officers are physically less tailored to their jobs than their male and younger colleagues.

Characterizing interactive engagement activities in a flipped introductory physics class

Directory of Open Access Journals (Sweden)

Anna K. Wood

2016-06-01

Full Text Available Interactive engagement activities are increasingly common in undergraduate physics teaching. As research efforts move beyond simply showing that interactive engagement pedagogies work towards developing an understanding of how they lead to improved learning outcomes, a detailed analysis of the way in which these activities are used in practice is needed. Our aim in this paper is to present a characterization of the type and duration of interactions, as experienced by students, that took place during two introductory physics courses (1A and 1B at a university in the United Kingdom. Through this work, a simple framework for analyzing lectures—the framework for interactive learning in lectures (FILL, which focuses on student interactions (with the lecturer, with each other, and with the material is proposed. The pedagogical approach is based on Peer Instruction (PI and both courses are taught by the same lecturer. We find lecture activities can be categorized into three types: interactive (25%, vicarious interactive (20% (involving questions to and from the lecturer, and noninteractive (55%. As expected, the majority of both interactive and vicarious interactive activities took place during PI. However, the way that interactive activities were used during non-PI sections of the lecture varied significantly between the two courses. Differences were also found in the average time spent on lecturer-student interactions (28% for 1A and 12% for 1B, although not on student-student interactions (12% and 12% or on individual learning (10% and 7%. These results are explored in detail and the implications for future research are discussed.

3D Printing and Digital Rock Physics for Geomaterials

Science.gov (United States)

Martinez, M. J.; Yoon, H.; Dewers, T. A.

2015-12-01

Imaging techniques for the analysis of porous structures have revolutionized our ability to quantitatively characterize geomaterials. Digital representations of rock from CT images and physics modeling based on these pore structures provide the opportunity to further advance our quantitative understanding of fluid flow, geomechanics, and geochemistry, and the emergence of coupled behaviors. Additive manufacturing, commonly known as 3D printing, has revolutionized production of custom parts with complex internal geometries. For the geosciences, recent advances in 3D printing technology may be co-opted to print reproducible porous structures derived from CT-imaging of actual rocks for experimental testing. The use of 3D printed microstructure allows us to surmount typical problems associated with sample-to-sample heterogeneity that plague rock physics testing and to test material response independent from pore-structure variability. Together, imaging, digital rocks and 3D printing potentially enables a new workflow for understanding coupled geophysical processes in a real, but well-defined setting circumventing typical issues associated with reproducibility, enabling full characterization and thus connection of physical phenomena to structure. In this talk we will discuss the possibilities that these technologies can bring to geosciences and present early experiences with coupled multiscale experimental and numerical analysis using 3D printed fractured rock specimens. In particular, we discuss the processes of selection and printing of transparent fractured specimens based on 3D reconstruction of micro-fractured rock to study fluid flow characterization and manipulation. Micro-particle image velocimetry is used to directly visualize 3D single and multiphase flow velocity in 3D fracture networks. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U

A normalization of the physical tests for external irradiation measuring detectors

International Nuclear Information System (INIS)

1977-05-01

This report is the result of a normalization work, realized within the Radioprotection Services of the C.E.A., of the physical tests for detectors measuring external irradiation. Among the various tests mentionned are treated more in details, calibration and the establishment of the relative spectral response. As far as calibration is concerned, the normalization refers to: the reference detector, the reference radiation source, the installation and calibration procedure. As for the relative spectral response the normalization refers to: the reference detector, the radiation sources to be used. Finally, a chapter is consecrated to the high flux detectors and to those for pulsed electromagnetic radiations [fr

Promoting physical activity: development and testing of self-determination theory-based interventions

Science.gov (United States)

2012-01-01

A growing number of studies have pulled from Deci and Ryan's Self-Determination Theory to design interventions targeting health behavior change. More recently, researchers have begun using SDT to promote the adoption and maintenance of an active lifestyle. In this review, we aim to highlight how researchers and practitioners can draw from the SDT framework to develop, implement, and evaluate intervention efforts centered on increasing physical activity levels in different contexts and different populations. In the present paper, the rationale for using SDT to foster physical activity engagement is briefly reviewed before particular attention is given to three recent randomized controlled trials, the Canadian Physical Activity Counseling (PAC) Trial, the Empower trial from the UK, and the Portuguese PESO (Promotion of Health and Exercise in Obesity) trial, each of which focused on promoting physical activity behavior. The SDT-based intervention components, procedures, and participants are highlighted, and the key findings that have emanated from these three trials are presented. Lastly, we outline some of the limitations of the work conducted to date in this area and we acknowledge the challenges that arise when attempting to design, deliver, and test SDT-grounded interventions in the context of physical activity promotion. PMID:22385751

Characterization of holding brake friction pad surface after pin-on-plate wear test

Science.gov (United States)

Drago, N.; Gonzalez Madruga, D.; De Chiffre, L.

2018-03-01

This article concerns the metrological characterization of the surface on a holding brake friction material pin after a pin-on-plate (POP) wear test. The POP test induces the formation of surface plateaus that affect brake performances such as wear, friction, noise and heat. Three different materials’ surfaces have been characterized after wear from data obtained with a focus variation 3D microscope. A new surface characterization approach with plateau identification is proposed, using the number of plateau on the surface, equivalent diameter, length and breadth as measurands. The identification method is based on determining and imposing ISO 27158-2 lower plateau limit (LPL) in material probability curves; and on applying a combined criterion of height segmentation threshold and equivalent diameter threshold. The method determines the criterion thresholds for each material since LPL appears typical by material. The proposed method has allowed quantifying the surface topography at two different levels of wear. An expanded measurement uncertainty of 3.5 µm for plateau dimensions in the range 50–2000 µm and one of 0.15 µm for plateau heights up to 10 µm have been documented.

Physics through the 1990s: Atomic, molecular, and optical physics

International Nuclear Information System (INIS)

1986-01-01

This report was prepared by the Panel on Atomic, Molecular, and Optical Physics of the Physics Survey Committee in response to its charge to describe the field, to characterize the recent advances, and to identify the current frontiers of research. Some of the areas discussed are: atomic structure, atomic dynamics, accelerator-based atomic physics, molecular photoionization and electron-molecule scattering, astrophysics, laser spectroscopy, atmospheric physics, plasma physics, and applications

Fuel Thermo-physical Characterization Project: Evaluation of Models to Calculate Thermal Diffusivity of Layered Composites

Energy Technology Data Exchange (ETDEWEB)

Burkes, Douglas [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Casella, Amanda J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Gardner, Levi D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Casella, Andrew M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Huber, Tanja K. [Technische Universität München, Munich (Germany); Breitkreutz, Harald [Technische Universität München, Munich (Germany)

2015-02-11

The Office of Material Management and Minimization Fuel Thermo-physical Characterization Project at Pacific Northwest National Laboratory (PNNL) is tasked with using PNNL facilities and processes to receive irradiated low enriched uranium-molybdenum fuel plate samples and perform analyses in support of the Office of Material Management and Minimization Reactor Conversion Program. This work is in support of the Fuel Development Pillar that is managed by Idaho National Laboratory. A key portion of the scope associated with this project was to measure the thermal properties of fuel segments harvested from plates that were irradiated in the Advanced Test Reactor. Thermal diffusivity of samples prepared from the fuel segments was measured using laser flash analysis. Two models, one developed by PNNL and the other developed by the Technische Universität München (TUM), were evaluated to extract the thermal diffusivity of the uranium-molybdenum alloy from measurements made on the irradiated, layered composites. The experimental data of the “TC” irradiated fuel segment was evaluated using both models considering a three-layer and five-layer system. Both models are in acceptable agreement with one another and indicate that the zirconium diffusion barrier has a minimal impact on the overall thermal diffusivity of the monolithic U-Mo fuel.

Proposed particle-beam characterizations for the APS undulator test line

Energy Technology Data Exchange (ETDEWEB)

Lumpkin, A.H.; Borland, M.; Milton, S.

1993-09-01

A research and development effort is underway at the Advanced Photon Source (APS) to use an rf gun as a low-emittance electron source for injection into the 100- to 650-MeV linac subsystem and subsequently to an undulator test area. This configuration would combine the acceleration capability of the 200-MeV S-band electron linac and the in-line 450-MeV positron linac that normally provide positrons to the positron accumulator ring (PAR). A transport line that bypasses the PAR will bring the electrons to the undulator test area. Characterization techniques will be discussed for the electron beam with a normalized, rms emittance of <10 {pi} mm mrad (1{sigma}) at micropulse charges of up to 350 pC and micropulse durations of {approximately}5 ps (FWHM). Tests proposed include measurement of particle beam transport effects (at one-tenth the storage ring beam rigidity) caused by small undulator field errors as well as operations intended to produce coherent, short wavelength radiation (<200 nm).

A regulator's perspective on physical testing for type B packages

International Nuclear Information System (INIS)

Brach, William E.

2004-01-01

The U.S. Nuclear Regulatory Commission has a great deal of experience certifying Type B transport packages as complying with the regulations in 10 CFR Part 71. With this experience base, supporting risk studies, and with an exceptional historical safety record for transport, we are very confident in both the current regulations and the methods we use to review and certify transportation packages. Nevertheless, we have a responsibility to remain vigilant and review our regulations and implementing practices with a view towards continuous improvement. NRC regulations permit certification through testing, analyses, comparison to similar approved designs, or combinations of these methods. Testing can be further broken into scale models, components, simple models, or full-scale models. NRC does not require full-scale testing for certification of any package; however, many applicants for package certification have conducted a physical testing program to demonstrate that the package design meets the hypothetical accident conditions. The plans for a repository at Yucca Mountain have raised significant interest in the United States of America in transportation of spent fuel, and created a broad stakeholder and public interest in transportation package testing. As an expected large increase in the number of spent fuel transports nears, this interest will likely grow. The technical and regulatory reasons for, or for not, performing tests need to be well understood and communicated to all stakeholders

Multi-Attribute Seismic/Rock Physics Approach to Characterizing Fractured Reservoirs

Energy Technology Data Exchange (ETDEWEB)

Gary Mavko

2004-11-30

Most current seismic methods to seismically characterize fractures in tight reservoirs depend on a few anisotropic wave propagation signatures that can arise from aligned fractures. While seismic anisotropy can be a powerful fracture diagnostic, a number of situations can lessen its usefulness or introduce interpretation ambiguities. Fortunately, laboratory and theoretical work in rock physics indicates that a much broader spectrum of fracture seismic signatures can occur, including a decrease in P- and S-wave velocities, a change in Poisson's ratio, an increase in velocity dispersion and wave attenuation, as well as well as indirect images of structural features that can control fracture occurrence. The goal of this project was to demonstrate a practical interpretation and integration strategy for detecting and characterizing natural fractures in rocks. The approach was to exploit as many sources of information as possible, and to use the principles of rock physics as the link among seismic, geologic, and log data. Since no single seismic attribute is a reliable fracture indicator in all situations, the focus was to develop a quantitative scheme for integrating the diverse sources of information. The integrated study incorporated three key elements: The first element was establishing prior constraints on fracture occurrence, based on laboratory data, previous field observations, and geologic patterns of fracturing. The geologic aspects include analysis of the stratigraphic, structural, and tectonic environments of the field sites. Field observations and geomechanical analysis indicates that fractures tend to occur in the more brittle facies, for example, in tight sands and carbonates. In contrast, strain in shale is more likely to be accommodated by ductile flow. Hence, prior knowledge of bed thickness and facies architecture, calibrated to outcrops, are powerful constraints on the interpreted fracture distribution. Another important constraint is that

Packaging of MEMS/MOEMS and nanodevices: reliability, testing, and characterization aspects

Science.gov (United States)

Tekin, Tolga; Ngo, Ha-Duong; Wittler, Olaf; Bouhlal, Bouchaib; Lang, Klaus-Dieter

2011-02-01

The last decade witnessed an explosive growth in research and development efforts devoted to MEMS devices and packaging. The successfully developed MEMS devices are, for example inkjet, pressure sensors, silicon microphones, accelerometers, gyroscopes, MOEMS, micro fuel cells and emerging MEMS. For the next decade, MEMS/MOEMS and nanodevice based products will penetrate into IT, telecommunications, automotive, defense, life sciences, medical and implantable applications. Forecasts say the MEMS market to be $14 billion by 2012. The packaging cost of MEMS/MOEMS products in general is about 70 percent. Unlike today's electronics IC packaging, their packaging are custom-built and difficult due to the moving structural elements. In order for the moving elements of a MEMS device to move effectively in a well-controlled atmosphere, hermetic sealing of the MEMS device in a cap is necessary. For some MEMS devices, such as resonators and gyroscopes, vacuum packaging is required. Usually, the cap is processed at the wafer level, and thus MEMS packaging is truly a wafer level packaging. In terms of MEMS/MOEMS and nanodevice packaging, there are still many critical issues need to be addressed due to the increasing integration density supported by 3D heterogeneous integration of multi-physic components/layers consisting of photonics, electronics, rf, plasmonics, and wireless. The infrastructure of MEMS/MOEMS and nanodevices and their packaging is not well established yet. Generic packaging platform technologies are not available. Some of critical issues have been studied intensively in the last years. In this paper we will discuss about processes, reliability, testing and characterization of MEMS/MOEMS and nanodevice packaging.

Physical readiness and performance of adolescents of different somatotype

Directory of Open Access Journals (Sweden)

V. M. Mysiv

2014-04-01

Full Text Available Purpose: to investigate the rate of puberty, changes in indicators of physical fitness and physical activity at the same somatotype different boys in the age range from 11 to 14 years. Material : 123 teenager were examined. The values of the studied parameters were determined at the beginning of each new school year. Tests were used to assess the major conditional qualities and coordination abilities. Results : the overall physical performance of boys of macrosplanchnic somatotype characterized annual trend towards improvement, except for the period between 11 and 12 years. Significant differences are typical for physical performance, except asthenoid and macrosplanchnic somatotype. Typological features installed due to changes in the studied parameters. Conclusions: noted the need to consider the data in shaping the content of physical education in improving orientation.

A study on the intrusion model by physical modeling

Energy Technology Data Exchange (ETDEWEB)

Kim, Jung Yul; Kim, Yoo Sung; Hyun, Hye Ja [Korea Inst. of Geology Mining and Materials, Taejon (Korea, Republic of)

1995-12-01

In physical modeling, the actual phenomena of seismic wave propagation are directly measured like field survey and furthermore the structure and physical properties of subsurface can be known. So the measured datasets from physical modeling can be very desirable as input data to test the efficiency of various inversion algorithms. An underground structure formed by intrusion, which can be often seen in seismic section for oil exploration, is investigated by physical modeling. The model is characterized by various types of layer boundaries with steep dip angle. Therefore, this physical modeling data are very available not only to interpret seismic sections for oil exploration as a case history, but also to develop data processing techniques and estimate the capability of software such as migration, full waveform inversion. (author). 5 refs., 18 figs.

Distribution and characterization of radionuclides in soils from Nevada Test Site

International Nuclear Information System (INIS)

Lee, S.Y.; Tamura, T.

1985-01-01

Selected physicochemical properties of plutonium-bearing radioactive particles and their association with host soils from the Nevada Test Site (NTS) were studied to aid in the environmental assessment of the radionuclides in the area and to provide technological concepts for potential cleanup operations. The dominant radioactive particles were amorphous to X-ray diffraction, very fragile by compression tests, and extremely porous with particle density 3 . The physical properties of the particles suggest that they can be broken to smaller respirable sizes by saltation during wind erosion and that their unique physical properties may be useful for mechanically separating them from the nonradioactive soil particles. Experimental results revealed that more than 90% of the total radioactivity was recovered in about 25% of the total sample weight through density separation techniques and in about 18% of the total weight by a grinding-sieving process. Radioactive particles might therefore be removed from the contaminated soil by a controlled vacuum collector, density separation, grinding-sieving separation, or a combination of these techniques on the basis of the density and compressibility differences between radioactive and nonradioactive particles. 21 references, 5 figures, 5 tables

Optimization of Asphalt Mixture Design for the Louisiana ALF Test Sections

Science.gov (United States)

2018-05-01

This research presents an extensive study on the design and characterization of asphalt mixtures used in road pavements. Both mixture volumetrics and physical properties obtained from several laboratory tests were considered in optimizing the mixture...

Minimum Performance on Clinical Tests of Physical Function to Predict Walking 6,000 Steps/Day in Knee Osteoarthritis: An Observational Study.

Science.gov (United States)

Master, Hiral; Thoma, Louise M; Christiansen, Meredith B; Polakowski, Emily; Schmitt, Laura A; White, Daniel K

2018-07-01

Evidence of physical function difficulties, such as difficulty rising from a chair, may limit daily walking for people with knee osteoarthritis (OA). The purpose of this study was to identify minimum performance thresholds on clinical tests of physical function predictive to walking ≥6,000 steps/day. This benchmark is known to discriminate people with knee OA who develop functional limitation over time from those who do not. Using data from the Osteoarthritis Initiative, we quantified daily walking as average steps/day from an accelerometer (Actigraph GT1M) worn for ≥10 hours/day over 1 week. Physical function was quantified using 3 performance-based clinical tests: 5 times sit-to-stand test, walking speed (tested over 20 meters), and 400-meter walk test. To identify minimum performance thresholds for daily walking, we calculated physical function values corresponding to high specificity (80-95%) to predict walking ≥6,000 steps/day. Among 1,925 participants (mean ± SD age 65.1 ± 9.1 years, mean ± SD body mass index 28.4 ± 4.8 kg/m 2 , and 55% female) with valid accelerometer data, 54.9% walked ≥6,000 steps/day. High specificity thresholds of physical function for walking ≥6,000 steps/day ranged 11.4-14.0 seconds on the 5 times sit-to-stand test, 1.13-1.26 meters/second for walking speed, or 315-349 seconds on the 400-meter walk test. Not meeting these minimum performance thresholds on clinical tests of physical function may indicate inadequate physical ability to walk ≥6,000 steps/day for people with knee OA. Rehabilitation may be indicated to address underlying impairments limiting physical function. © 2017, American College of Rheumatology.

Results of physics start-up tests of Mochovce and Bohunice units with 2-nd generation Gd fuel (average enrichment 4.87 %)

International Nuclear Information System (INIS)

Polakovic, F.

2015-01-01

There are presented main features of the fuel and the list of experimental neutron-physical characteristics measured during physics start-up tests.All together there were carried out 14 physics start-ups at Bohunice and Mochovce Units with the new type of fuel. Differences between theoretical and experimental neutron-physical characteristics were statistically processed and compared with the tests acceptance criteria. There are summarized results of reactor physics start-ups with 2-nd generation Gd fuel usage [ru

Factors that affect the physical science career interest of female students: Testing five common hypotheses

Science.gov (United States)

Hazari, Zahra; Potvin, Geoff; Lock, Robynne M.; Lung, Florin; Sonnert, Gerhard; Sadler, Philip M.

2013-12-01

There are many hypotheses regarding factors that may encourage female students to pursue careers in the physical sciences. Using multivariate matching methods on national data drawn from the Persistence Research in Science and Engineering (PRiSE) project (n=7505), we test the following five commonly held beliefs regarding what factors might impact females’ physical science career interest: (i) having a single-sex physics class, (ii) having a female physics teacher, (iii) having female scientist guest speakers in physics class, (iv) discussing the work of female scientists in physics class, and (v) discussing the underrepresentation of women in physics class. The effect of these experiences on physical science career interest is compared for female students who are matched on several factors, including prior science interests, prior mathematics interests, grades in science, grades in mathematics, and years of enrollment in high school physics. No significant effects are found for single-sex classes, female teachers, female scientist guest speakers, and discussing the work of female scientists. However, discussions about women’s underrepresentation have a significant positive effect.

Particle characterization of contaminated soil

International Nuclear Information System (INIS)

Miller, J.D.; Hupka, J.; Weidner, J.R.

1991-05-01

Samples collected from Test Reactor Area Warm Waste Pond sediments at the Idaho National Engineering Laboratory were characterized in the test facilities in the Metallurgy Department, University of Utah. The sediments were characterized in terms of several physical, chemical, and mineralogical properties judged to be most important for separating radioactive materials and hazardous metals from the sediment matrix. The properties include particle size, distribution, effects of heating at 600 degrees C, electrophoretic properties, magnetic separation, acid leaching, and analyses using ultra-violet light, infra-red, and x-ray diffraction. The results show that most radioactive and hazardous metals are present in the ≤ 150 micron size fraction and that 80% of the sediments occur in the ≥ 150 micron size fraction. No significant concentration of hazardous metals was found to be related to magnetic properties. Organic matter, probably as a thin film, was shown to be present. The mineralogy of the samples include quartz, chlorite, kaolinite, illite, calcite, and dolomite. 3 refs., 17 figs., 5 tabs

Material characterization and non destructive testing by ultrasounds; modelling, simulation and experimental validation

International Nuclear Information System (INIS)

Noroy-Nadal, M.H.

2002-06-01

This memory presents the research concerning the characterization of materials and the Non Destructive Testing (N.D.T) by ultrasonics. The different topics include three steps: modeling, computations and experimental validation. The studied materials concern mainly metals. The memory is divided in four parts. The first one concerns the characterization of materials versus temperature. The determination of the shear modulus G(T) is especially studied for a large temperature range, and around the melting point. The second part is devoted to studies by photothermal devices essentially focused on the modeling of the mechanical displacement and the stress field in coated materials. In this particular field of interest, applications concern either the mechanical characterization of the coating, the defect detection in the structure and finally the evaluation of the coating adhesion. The third section is dedicated to microstructural characterization using acoustic microscopy. The evaluation of crystallographic texture is especially approached, for metallic objects obtained by forming. Before concluding and pointing out some perspectives to this work, the last section concerns the introduction of optimization techniques, applied to the material characterization by acoustic microscopy. (author)

The reactor core configuration and important systems related to physics tests of Daya Bay NPP

International Nuclear Information System (INIS)

Tao Shaoping

1995-06-01

A brief introduction to reactor core configuration and important systems related to physics tests of Daya Bay NPP is given. These systems involve the reactor core system (COR), the full length rod control system (RGL), the in-core instrumentation system (RIC), the out-of-core nuclear instrumentation system (RPN), and the LOCA surveillance system (LSS), the centralized data processing system (KIT) and the test data acquisition system (KDO). In addition, that the adjustment and evaluation of boron concentration related to other systems, for example the reactor coolant system (RCP), the chemical and volume control system (RCV), the reactor boron and water makeup system (REA), the nuclear sampling system (REN) and the reactor control system (RRC), etc. is also described. Analysis of these systems helps not only to familiarize their functions and acquires a deepen understanding for the principle procedure, points for attention and technical key of the core physics tests, but also to further analyze the test results. (3 refs., 11 figs., 1 tab.)

The CEBAF test package: A symbolic and dynamic test, histogram and parameter package for on- and off-line particle physics data analysis

International Nuclear Information System (INIS)

Wood, S.A.; Abbott, S.

1995-01-01

Nuclear physics data analysis programs often use packages, such as Q, that allow parameter values, test definitions and histogram booking parameters to be controlled at run time through external files or shared memory. Data within a physics analyzer are usually referenced by indices, leading to a high use of equivalence statements and to extra bookkeeping. In the CEBAF Test Package (CTP), parameters, tests and histogram definitions defined in external files all refer to data elements by the same variable names as used in the C or Fortran source code for the analyzer. This is accomplished by requirieng the analyzer developer to open-quotes registerclose quotes each variable and array that is to be accessible by the package. Any registered variable as well as the test and histogram definitions may be dynamically read and modified by tasks that communicate via standard networking calls. As this package is implemented in C and requires only HBOOK and SUN RPC networking, it is highly portable. CTP works with the CEBAF Online Data Acquisition system (CODA), but may be used with other data acquisition systems or stand alone

Cement for oil well developed from ordinary cement: characterization physical, chemical and mineralogical

International Nuclear Information System (INIS)

Oliveira, D.N.S.; Neves, G. de A.; Chaves, A.C.; Mendonca, A.M.G.D.; Lima, M.S. de; Bezerra, U.T.

2012-01-01

This work aims to characterize a new type of cement produced from the mixture of ordinary Portland cement, which can be used as an option in the cementing of oil wells. To enable this work we used the method of lineal programming for the new cement composition, then conducted tests to characterize through particle size analysis by laser diffraction, chemical analysis by EDX, TGA, X-ray diffraction, time grip, resistance to compression. The overall result showed that the new cement had made low-C3A, takes more time to the CPP, thermal stability up to 500 ° C, the kinetics of hydration and low levels of major components consistent with the specifications of ABNT. (author)

Evaluation of spacer grid spring characteristics by means of physical tests and numerical simulation

Energy Technology Data Exchange (ETDEWEB)

Schettino, Carlos Frederico Mattos, E-mail: carlosschettino@inb.gov.br [Industrias Nucleares do Brasil (INB), Resende, RJ (Brazil)

2017-11-01

Among all fuel assemblies' components, the spacer grids play an important structural role during the energy generation process, mainly due for its primary functional requirement, that is, to provide fuel rod support. The present work aims to evaluate the spring characteristics of a specific spacer grid design used in a PWR fuel assembly type 16 x 16. These spring characteristics comprises the load versus deflection capability and its spring rate, which are very important, and also mandatory, to be correctly established in order to preclude spacer grid spring and fuel rod cladding fretting during operation, as well as prevent an excessive fuel rod buckling. This study includes physical tests and numerical simulation. The tests were performed on an adapted load cell mechanical device, using as a specimen a single strap of the spacer grid. Three numerical models were prepared using the Finite Element Method, with the support of the commercial code ANSYS. One model was built to validate the simulation according to the performed physical test, the others were built inserting a gradient of temperature (Beginning Of Life hot condition) and to evaluate the spacer grid spring characteristics in End Of Life condition. The obtained results from physical test and numerical model have shown a good agreement between them, therefore validating the simulation. The obtained results from numerical models make available information regarding the spacer grid design purpose, such as the behavior of the fuel rod cladding support during operation. Therewith, these evaluations could be useful to improve the spacer grid design. (author)

Evaluation of spacer grid spring characteristics by means of physical tests and numerical simulation

International Nuclear Information System (INIS)

Schettino, Carlos Frederico Mattos

2017-01-01

Among all fuel assemblies' components, the spacer grids play an important structural role during the energy generation process, mainly due for its primary functional requirement, that is, to provide fuel rod support. The present work aims to evaluate the spring characteristics of a specific spacer grid design used in a PWR fuel assembly type 16 x 16. These spring characteristics comprises the load versus deflection capability and its spring rate, which are very important, and also mandatory, to be correctly established in order to preclude spacer grid spring and fuel rod cladding fretting during operation, as well as prevent an excessive fuel rod buckling. This study includes physical tests and numerical simulation. The tests were performed on an adapted load cell mechanical device, using as a specimen a single strap of the spacer grid. Three numerical models were prepared using the Finite Element Method, with the support of the commercial code ANSYS. One model was built to validate the simulation according to the performed physical test, the others were built inserting a gradient of temperature (Beginning Of Life hot condition) and to evaluate the spacer grid spring characteristics in End Of Life condition. The obtained results from physical test and numerical model have shown a good agreement between them, therefore validating the simulation. The obtained results from numerical models make available information regarding the spacer grid design purpose, such as the behavior of the fuel rod cladding support during operation. Therewith, these evaluations could be useful to improve the spacer grid design. (author)

Feasibility and Reliability of Tests Measuring Health-Related Physical Fitness in Children with Moderate to Severe Levels of Intellectual Disability

Science.gov (United States)

Wouters, Marieke; van der Zanden, Anna M.; Evenhuis, Heleen M.; Hilgenkamp, Thessa I. M.

2017-01-01

Physical fitness is an important marker for health. In this study we investigated the feasibility and reliability of health-related physical fitness tests in children with moderate to severe levels of intellectual disability. Thirty-nine children (2-18 yrs) performed tests for muscular strength and endurance, the modified 6-minute walk test (6mwt)…

Characterization and testing of monolithic RERTR fuel plates

Energy Technology Data Exchange (ETDEWEB)

Keiser, D.D.; Jue, J.F.; Burkes, D.E. [Idaho National Lab., Idaho Falls, ID (United States)

2007-07-01

Monolithic fuel plates are being developed as a LEU (low enrichment uranium) fuel for application in research reactors throughout the world. These fuel plates are comprised of a U-Mo alloy foil encased in aluminum alloy cladding. Three different fabrication techniques have been looked at for producing monolithic fuel plates: hot isostatic pressing (HIP), transient liquid phase bonding (TLPB), and friction stir welding (FSW). Of these three techniques, HIP and FSW are currently being emphasized. As part of the development of these fabrication techniques, fuel plates are characterized and tested to determine properties like hardness and the bond strength at the interface between the fuel and cladding. Testing of HIP-made samples indicates that the foil/cladding interaction behavior depends on the Mo content in the UMo foil, the measured hardness values are quite different for the fuel, cladding, and interaction zone phase and Ti, Zr and Nb are the most effective diffusion barriers. For FSW samples, there is a dependence of the bond strength at the foil/cladding interface on the type of tool that is employed for performing the actual FSW process. (authors)

Environmental assessment for the Groundwater Characterization Project, Nevada Test Site, Nye County, Nevada

International Nuclear Information System (INIS)