Catalytic Pyrolysis of Tar Model Compound with Various Bio-Char Catalysts to Recycle Char from Biomass Pyrolysis

Directory of Open Access Journals (Sweden)

Jinmiao Liu

2016-03-01

Full Text Available Tar and char can be regarded as unwanted byproducts during the gasification process. In this study, three types of catalyst, i.e., biomass char (bio-char, nickel supported on biomass (Ni+bio-char, and nickel supported on bio-char (bio-char+Ni, were studied to compare the catalytic effects of different preparation methods on tar model compound removal. The structural characteristics of the three catalysts were also investigated by X-ray diffraction (XRD, scanning electron microscopy (SEM, and Brunauer-Emmett-Teller (BET methods. The results revealed that Ni+bio-char catalyst showed much higher activity for the reformation of toluene (C7H8 as a tar model compound than the other two catalysts. Toluene could be completely converted to small gas molecules at a conversion rate of 99.92% at 800 °C, and the maximum yield of gas was 432 mL/(mL C7H8. In particular, the H2 and CH4 yields were 339 and 85 mL/(mL C7H8 at 850 °C, respectively. An N2 absorption-desorption experiment demonstrated that the specific surface area of Ni+bio-char was 32.87 times that of bio-char and 8.39 times that of bio-char+Ni. Moreover, metallic nickel (Ni0 particles could be generated in the carbon matrix of Ni+bio-char catalyst. SEM analysis confirmed that the Ni+bio-char catalyst had a more porous structure. Nickel supported on biomass might be a promising catalyst for tar reformation because of its excellent catalytic activities.

The ChemChar process for hazardous-waste treatment

International Nuclear Information System (INIS)

McGowin, A.E.

1991-01-01

The ChemChar Reverse-Burn Gasification Process has been studied for application to the thermal destruction of radioactive waste organic ion exchange resins. The resulting char was mixed with cement to form a dry, leach-resistant final disposal product. Successful regeneration of spent granular activated carbons was achieved with reverse-burn gasification. Regeneration parameters such as moisture content and supplemental fuel addition were investigated. The performance of regenerated carbon was evaluated by batch equilibrium and breakthrough assay and was comparable to that of the original. Surface areas were determined by the BET method. The fate of mercury during reverse-burn gasification was investigated. TRB Char adsorbent was used to remove mercury vapor emission from the process. The use of petroleum coke as a substrate for gasification of wastes was studied. Petroleum coke was activated by reverse-burn gasification to produce a highly porous, low surface area solid. Destruction efficiency for hexachlorobenzene on activated coke was considerably lower than on coal char, however, the addition of iron appeared to catalyze hexachlorobenzene gasification

Influence of pH on pesticide sorption by soil containing wheat residue-derived char

International Nuclear Information System (INIS)

Sheng Guangyao; Yang Yaning; Huang Minsheng; Yang Kai

2005-01-01

Field burning of crop residues incorporates resulting chars into soil and may thus influence the environmental fate of pesticides in the soil. This study evaluated the influence of pH on the sorption of diuron, bromoxynil, and ametryne by a soil in the presence and absence of a wheat residue-derived char. The sorption was measured at pHs ∼3.0 and ∼7.0. Wheat char was found to be a highly effective sorbent for the pesticides, and its presence (1% by weight) in soil contributed >70% to the pesticide sorption (with one exception). The sorption of diuron was not influenced by pH, due to its electroneutrality. Bromoxynil becomes dissociated at high pHs to form anionic species. Its sorption by soil and wheat char was lower at pH ∼7.0 than at pH ∼3.0, probably due to reduced partition of the anionic species of bromoxynil into soil organic matter and its weak interaction with the carbon surface of the char. Ametryne in its molecular form at pH ∼7.0 was sorbed by char-amended soil via partitioning into soil organic matter and interaction with the carbon surface of the char. Protonated ametryne at pH ∼3.0 was substantially sorbed by soil primarily via electrostatic forces. Sorption of protonated ametryne by wheat char was also significant, likely due not only to the interaction with the carbon surface but also to interactions with hydrated silica and surface functional groups of the char. Sorption of ametryne by char-amended soil at pH ∼3.0 was thus influenced by both the soil and the char. Environmental conditions may thus significantly influence the sorption and behavior of pesticides in agricultural soils containing crop residue-derived chars. - Wheat char was effective for adsorption of pesticides in soil, with efficacy varying with pH and particular pesticides

Influence of pH on pesticide sorption by soil containing wheat residue-derived char

Energy Technology Data Exchange (ETDEWEB)

Sheng Guangyao [Department of Crop, Soil, and Environmental Sciences, University of Arkansas, Fayetteville, AR 72701 (United States)]. E-mail: gsheng@uark.edu; Yang Yaning [Department of Crop, Soil, and Environmental Sciences, University of Arkansas, Fayetteville, AR 72701 (United States); Huang Minsheng [Department of Environmental Science and Technology, East China Normal University, Shanghai 200062 (China); Yang Kai [Department of Environmental Science and Technology, East China Normal University, Shanghai 200062 (China)

2005-04-01

Field burning of crop residues incorporates resulting chars into soil and may thus influence the environmental fate of pesticides in the soil. This study evaluated the influence of pH on the sorption of diuron, bromoxynil, and ametryne by a soil in the presence and absence of a wheat residue-derived char. The sorption was measured at pHs {approx}3.0 and {approx}7.0. Wheat char was found to be a highly effective sorbent for the pesticides, and its presence (1% by weight) in soil contributed >70% to the pesticide sorption (with one exception). The sorption of diuron was not influenced by pH, due to its electroneutrality. Bromoxynil becomes dissociated at high pHs to form anionic species. Its sorption by soil and wheat char was lower at pH {approx}7.0 than at pH {approx}3.0, probably due to reduced partition of the anionic species of bromoxynil into soil organic matter and its weak interaction with the carbon surface of the char. Ametryne in its molecular form at pH {approx}7.0 was sorbed by char-amended soil via partitioning into soil organic matter and interaction with the carbon surface of the char. Protonated ametryne at pH {approx}3.0 was substantially sorbed by soil primarily via electrostatic forces. Sorption of protonated ametryne by wheat char was also significant, likely due not only to the interaction with the carbon surface but also to interactions with hydrated silica and surface functional groups of the char. Sorption of ametryne by char-amended soil at pH {approx}3.0 was thus influenced by both the soil and the char. Environmental conditions may thus significantly influence the sorption and behavior of pesticides in agricultural soils containing crop residue-derived chars. - Wheat char was effective for adsorption of pesticides in soil, with efficacy varying with pH and particular pesticides.

Structural features of resorcinol–formaldehyde resin chars and interfacial behavior of water co-adsorbed with low-molecular weight organics

International Nuclear Information System (INIS)

Gun’ko, Vladimir M.; Bogatyrov, Viktor M.; Turov, Vladimir V.; Leboda, Roman; Skubiszewska-Zięba, Jadwiga; Urubkov, Iliya V.

2013-01-01

Products of resorcinol–formaldehyde resin carbonization (chars) are characterized by different morphology (particle shape and sizes) and texture (specific surface area, pore volume and pore size distribution) depending on water content during resin polymerization. At a low amount of water (C w = 37.8 wt.%) during synthesis resulting in strongly cross-linked polymers, carbonization gives nonporous particles. An increase in the water content to 62.7 wt.% results in a nano/mesoporous char, but if C w = 73.3 wt.%, a char is purely nanoporous. Despite these textural differences, the Raman spectra of all the chars are similar because of the similarity in the structure of their carbon sheets with a significant contribution of sp 3 C atoms. However, the difference in the spatial organization of the carbon sheet stacks in the particles results in the significant differences in the textural and morphological characteristics and in the adsorption properties of chars with respect to water, methane, benzene, hydrogen, methylene chloride, and dimethylsulfoxide.

Structural features of resorcinol–formaldehyde resin chars and interfacial behavior of water co-adsorbed with low-molecular weight organics

Energy Technology Data Exchange (ETDEWEB)

Gun’ko, Vladimir M., E-mail: vlad_gunko@ukr.net [Chuiko Institute of Surface Chemistry, 17 General Naumov Street, 03164 Kyiv (Ukraine); Bogatyrov, Viktor M.; Turov, Vladimir V. [Chuiko Institute of Surface Chemistry, 17 General Naumov Street, 03164 Kyiv (Ukraine); Leboda, Roman; Skubiszewska-Zięba, Jadwiga [Faculty of Chemistry, Maria Curie-Skłodowska University, 20031 Lublin (Poland); Urubkov, Iliya V. [Kurdyumov Institute of Metal Physics, 36 Vernadsky Boulevard, 03142 Kyiv (Ukraine)

2013-10-15

Products of resorcinol–formaldehyde resin carbonization (chars) are characterized by different morphology (particle shape and sizes) and texture (specific surface area, pore volume and pore size distribution) depending on water content during resin polymerization. At a low amount of water (C{sub w} = 37.8 wt.%) during synthesis resulting in strongly cross-linked polymers, carbonization gives nonporous particles. An increase in the water content to 62.7 wt.% results in a nano/mesoporous char, but if C{sub w} = 73.3 wt.%, a char is purely nanoporous. Despite these textural differences, the Raman spectra of all the chars are similar because of the similarity in the structure of their carbon sheets with a significant contribution of sp{sup 3} C atoms. However, the difference in the spatial organization of the carbon sheet stacks in the particles results in the significant differences in the textural and morphological characteristics and in the adsorption properties of chars with respect to water, methane, benzene, hydrogen, methylene chloride, and dimethylsulfoxide.

Suspension Combustion of Wood: Influence of Pyrolysis Conditions on Char Yield, Morphology, and Reactivity

DEFF Research Database (Denmark)

Dall'Ora, Michelangelo; Jensen, Peter Arendt; Jensen, Anker Degn

2008-01-01

Chars from pine and beech wood were produced by fast pyrolysis in an entrained flow reactor and by slow pyrolysis in a thermogravimetric analyzer. The influence of pyrolysis temperature, heating rate and particle size on char yield and morphology was investigated. The applied pyrolysis temperature...... varied in the range 673−1673 K for slow pyrolysis and between 873 and 1573 K for fast pyrolysis. The chars were oxidized in a thermogravimetric analyzer and the mass loss data were used to determine char oxidation reactivity. Char yield from fast pyrolysis (104−105 K/s) was as low as 1 to 6% on a dry ash......, char oxidation reactivity decreased as pyrolysis temperature increased. The amount and composition of the ash forming matter of the wood fuels seems to play an important role in determining the differences in char yield, morphology and reactivity....

The effect of char structure on burnout during pulverized coal combustion at pressure

Energy Technology Data Exchange (ETDEWEB)

Liu, G.; Wu, H.; Benfell, K.E.; Lucas, J.A.; Wall, T.F.

1999-07-01

An Australian bituminous coal sample was burnt in a drop tube furnace (DTF) at 1 atm and a pressurized drop tube furnace (PDTF) at 15 atm. The char samples were collected at different burnout levels, and a scanning electron microscope was used to examine the structures of chars. A model was developed to predict the burnout of char particles with different structures. The model accounts for combustion of the thin-walled structure of cenospheric char and its fragmentation during burnout. The effect of pressure on reaction rate was also considered in the model. As a result, approximately 40% and 70% cenospheric char particles were observed in the char samples collected after coal pyrolysis in the DTF and PDTF respectively. A large number of fine particles (< 30 mm) were observed in the 1 atm char samples at burnout levels between 30% and 50%, which suggests that significant fragmentation occurred during early combustion. Ash particle size distributions show that a large number of small ash particles formed during burnout at high pressure. The time needed for 70% char burnout at 15 atm is approximately 1.6 times that at 1 atm under the same temperature and gas environment conditions, which is attributed to the different pressures as well as char structures. The overall reaction rate for cenospheric char was predicted to be approximately 2 times that of the dense chars, which is consistent with previous experimental results. The predicted char burnout including char structures agrees reasonably well with the experimental measurements that were obtained at 1 atm and 15 atm pressures.

Heterogeneous reduction of nitric oxide on synthetic coal chars

Energy Technology Data Exchange (ETDEWEB)

C. Pevida; A. Arenillas; F. Rubiera; J.J. Pis [Instituto Nacional del Carbon (CSIC), Oviedo (Spain)

2005-12-01

Model compounds, with a controlled heteroatoms content and well-defined functionalities, were used to study the release of nitrogen compounds from char combustion. In the present work, the mechanisms involved in NO-char heterogeneous reduction were studied with a synthetic coal (SC) char as carbon source. Another synthetic char (SN) without any nitrogen in its composition was also employed in these studies. Temperature programmed reduction (TPR) tests with a gas mixture of 400 ppm NO in argon and with isotopically labelled nitric oxide, {sup 15}NO (500 ppm {sup 15}NO in argon), were carried out. The gases produced were quantitatively determined by means of MS and FTIR analysers. Under the conditions of this work the main products of the NO-C reaction were found to be N{sub 2} and CO{sub 2}. The main path of reaction involves the formation of surface nitrogen compounds that afterwards react with nitrogen from the reactive gas to form N{sub 2}. It was observed that fuel-N also participates in the overall heterogeneous reduction reaction, although to a lesser extent.

Active sites in char gasification: Final technical report

Energy Technology Data Exchange (ETDEWEB)

Wojtowicz, M.; Lilly, W.D.; Perkins, M.T.; Hradil, G.; Calo, J.M.; Suuberg, E.M.

1987-09-01

Among the key variables in the design of gasifiers and combustors is the reactivity of the chars which must be gasified or combusted. Significant loss of unburned char is unacceptable in virtually any process; the provision of sufficient residence time for complete conversion is essential. A very wide range of reactivities are observed, depending upon the nature of the char in a process. The current work focuses on furthering the understanding of gasification reactivities of chars. It has been well established that the reactivity of char to gasification generally depends upon three principal factors: (1) the concentration of ''active sites'' in the char; (2) mass transfer within the char; and (3) the type and concentration of catalytic impurities in the char. The present study primarily addresses the first factor. The subject of this research is the origin, nature, and fate of active sites in chars derived from parent hydrocarbons with coal-like structure. The nature and number of the active sites and their reactivity towards oxygen are examined in ''model'' chars derived from phenol-formaldehyde type resins. How the active sites are lost by the process of thermal annealing during heat treatment of chars are studied, and actual rate for the annealing process is derived. Since intrinsic char reactivities are of primary interest in the present study, a fair amount of attention was given to the model char synthesis and handling so that the effect of catalytic impurities and oxygen-containing functional groups in the chemical structure of the material were minimized, if not completely eliminated. The project would not be considered complete without comparing characteristic features of synthetic chars with kinetic behavior exhibited by natural chars, including coal chars.

Co-gasification of tire and biomass for enhancement of tire-char reactivity in CO2 gasification process.

Science.gov (United States)

Lahijani, Pooya; Zainal, Zainal Alimuddin; Mohamed, Abdul Rahman; Mohammadi, Maedeh

2013-06-01

In this investigation, palm empty fruit bunch (EFB) and almond shell (AS) were implemented as two natural catalysts rich in alkali metals, especially potassium, to enhance the reactivity of tire-char through co-gasification process. Co-gasification experiments were conducted at several blending ratios using isothermal Thermogravimetric analysis (TGA) under CO2. The pronounced effect of inherent alkali content of biomass-chars on promoting the reactivity of tire-char was proven when acid-treated biomass-chars did not exert any catalytic effect on improving the reactivity of tire-char in co-gasification experiments. In kinetic studies of the co-gasified samples in chemically-controlled regime, modified random pore model (M-RPM) was adopted to describe the reactive behavior of the tire-char/biomass-char blends. By virtue of the catalytic effect of biomass, the activation energy for tire-char gasification was lowered from 250 kJ/mol in pure form 203 to 187 kJ/mol for AS-char and EFB-char co-gasified samples, respectively. Copyright © 2013 Elsevier Ltd. All rights reserved.

Bitumen on Water: Charred Hay as a PFD (Petroleum Flotation Device

Directory of Open Access Journals (Sweden)

Nusrat Jahan

2015-10-01

Full Text Available Global demand for petroleum keeps increasing while traditional supplies decline. One alternative to the use of conventional crude oils is the utilization of Canadian bitumen. Raw bitumen is a dense, viscous, semi-liquid that is diluted with lighter crude oil to permit its transport through pipelines to terminals where it can then be shipped to global markets. When spilled, it naturally weathers to its original form and becomes dense enough to sink in aquatic systems. This severely limits oil spill recovery and remediation options. Here we report on the application of charred hay as a method for modifying the surface behavior of bitumen in aquatic environments. Waste or surplus hay is abundant in North America. Its surface can easily be modified through charring and/or chemical treatment. We have characterized the modified and charred hay using solid-state NMR, contact angle measurements and infrared spectroscopy. Tests of these materials to treat spilled bitumen in model aquatic systems have been undertaken. Our results indicate that bitumen spills on water will retain their buoyancy for longer periods after treatment with charred hay, or charred hay coated with calcium oxide, improving recovery options.

Demineralisation of a semianthracite char with molten salts/HCl

International Nuclear Information System (INIS)

Alfaro-Dominguez, M.; Sanchez Bajo, F.

2006-01-01

The effects of chemical heat treatments of a semianthracite char (AC) on the composition of the mineral fraction of the material are investigated. The starting char was first treated with a mixture of LiCl/KCl or LiCl/KCl/CaO at 743, 873 or 1173 K and the products obtained were then washed thoroughly with distilled water. A small fraction of these samples were treated with 10 -3 M HCl solution. The composition changes were studied by X-ray diffraction. The predominant mineral components initially present in the starting char are quartz, mullite, muscovite and/or kaolinite and oldhamite. The treatments of AC resulted in significant changes in the mineral fraction of the material, in particular when LiCl/KCl/CaO was used. In this case, spurrite, γ-calcium orthosilicate and gehlenite were formed, which were eliminated by treatment with 10 -3 M HCl solution

Demineralisation of a semianthracite char with molten salts/HCl

Energy Technology Data Exchange (ETDEWEB)

Alfaro-Dominguez, M. [Departamento de Electronica e Ingenieria Electromecanica, Escuela de Ingenierias Industriales, Universidad de Extremadura, Avda de Elvas s/n, 06071 Badajoz (Spain)]. E-mail: malfaro@unex.es; Sanchez Bajo, F. [Departamento de Electronica e Ingenieria Electromecanica, Escuela de Ingenierias Industriales, Universidad de Extremadura, Avda de Elvas s/n, 06071 Badajoz (Spain)

2006-06-30

The effects of chemical heat treatments of a semianthracite char (AC) on the composition of the mineral fraction of the material are investigated. The starting char was first treated with a mixture of LiCl/KCl or LiCl/KCl/CaO at 743, 873 or 1173 K and the products obtained were then washed thoroughly with distilled water. A small fraction of these samples were treated with 10{sup -3} M HCl solution. The composition changes were studied by X-ray diffraction. The predominant mineral components initially present in the starting char are quartz, mullite, muscovite and/or kaolinite and oldhamite. The treatments of AC resulted in significant changes in the mineral fraction of the material, in particular when LiCl/KCl/CaO was used. In this case, spurrite, {gamma}-calcium orthosilicate and gehlenite were formed, which were eliminated by treatment with 10{sup -3} M HCl solution.

Determination of reactivity parameters of model carbons, cokes and flame-chars

DEFF Research Database (Denmark)

Sørensen, Lasse Holst; Gjernes, Erik; Jessen, Thomas

1996-01-01

Reactivity profiles are defined and measured with thermogravimetry for a dense metallurgical Longyear coke, a polymer-derived porous active carbon, Carboxen 1000, and three flame-chars, Illinois #6, Pittsburgh #8 and New Mexico Blue #1. For each sample it is found that the reactivity profile can...... and activation energy in oxygen are estimated for each sample over a 100 K temperature range (cases vary from 573 to 885 K) and a maximum oxygen partial pressure range of 0.01-1 bar. For the different fuel samples reaction orders range fromn =0.65 to 0.78, and global activation energies are found in the narrow...... range of 130-133 kJ/mol. For Carboxen n=0.91 and E=146 kJ/mol. The reactivity differences between the coal chars are proposed mainly due to variations in the physical structure. Over the pressure-temperature domain examined reactivity varies considerably, but the structural profile is approximately...

Effective Diffusion Coefficients in Coal Chars

DEFF Research Database (Denmark)

Johnsson, Jan Erik; Jensen, Anker

2001-01-01

Knowledge of effective diffusion coefficients in char particles is important when interpreting experimental reactivity measurements and modeling char combustion or NO and N2O reduction. In this work, NO and N2O reaction with a bituminous coal char was studied in a fixed-bed quartz glass reactor....... In the case of strong pore diffusion limitations, the error in the interpretation of experimental results using the mean pore radius could be a factor of 5 on the intrinsic rate constant. For an average coal char reacting with oxygen at 1300 K, this would be the case for particle sizes larger than about 50...

The ChemChar process

International Nuclear Information System (INIS)

Manahan, S.E.; Kinner, L.L.; Larsen, D.W.

1992-01-01

This paper reports on reverse-burn gasification is a thermochemical process that offers a number of advantages over conventional incineration for the treatment of a variety of waste materials. Patented as the ChemChar Process, reverse-burn gasification can treat wastes in the forms of solids, liquids, sludges, and soils. Waste constituents are destroyed by conversion to a combustible gas and to a dry, inert, carbonaceous solid which is either non-hazardous or can be readily mixed with cement to prevent leaching of the radioactive, toxic, or heavy metal constituents that are retained in the char residue or ash. In this way, reverse-burn gasification can be a very effective method for treating organic waste sludges containing heavy metals and mixed wastes consisting of hazardous chemicals contaminated with radioactive substances. As with any gasification waste treatment process, reverse-burn gasification offers inherent advantages in the areas of destruction efficiency and emissions control. This is because, instead of an exhaust gas that must treated to control emissions, gasification produces a combustible gas that is burned. Trace levels of contaminants are destroyed in burning the gas, and a catalyst may be employed, if necessary

Abundant and stable char residues in soils: implications for soil fertility and carbon sequestration.

Science.gov (United States)

Mao, J-D; Johnson, R L; Lehmann, J; Olk, D C; Neves, E G; Thompson, M L; Schmidt-Rohr, K

2012-09-04

Large-scale soil application of biochar may enhance soil fertility, increasing crop production for the growing human population, while also sequestering atmospheric carbon. But reaching these beneficial outcomes requires an understanding of the relationships among biochar's structure, stability, and contribution to soil fertility. Using quantitative (13)C nuclear magnetic resonance (NMR) spectroscopy, we show that Terra Preta soils (fertile anthropogenic dark earths in Amazonia that were enriched with char >800 years ago) consist predominantly of char residues composed of ~6 fused aromatic rings substituted by COO(-) groups that significantly increase the soils' cation-exchange capacity and thus the retention of plant nutrients. We also show that highly productive, grassland-derived soils in the U.S. (Mollisols) contain char (generated by presettlement fires) that is structurally comparable to char in the Terra Preta soils and much more abundant than previously thought (~40-50% of organic C). Our findings indicate that these oxidized char residues represent a particularly stable, abundant, and fertility-enhancing form of soil organic matter.

Imulation of polymer forming processes - addressing industrial needs

International Nuclear Information System (INIS)

Thibault, F.; DiRaddo, R.

2011-01-01

The objective of this paper is to present the development of simulation and design optimization capabilities, for polymer forming processes, in the context of addressing industrial needs. Accomplishments generated from close to twenty years of research in this field, at the National Research Council (NRC), are presented. Polymer forming processes such as extrusion blow moulding, stretch blow moulding and thermoforming have been the focus of the work, yet the research is extendable to similar polymer forming operations such as micro-blow moulding, sheet blow moulding and composites stamping. The research considers material models, process sequence integration and design optimization, derivative processes and 3D finite elements with multi-body contact.

Char characterisation and its application in a coal burnout mode

Energy Technology Data Exchange (ETDEWEB)

Michael Cloke; Tao Wu; Richelieu Barranco; Ed Lester [University of Nottingham, Nottingham (United Kingdom). Nottingham Fuel and Energy Centre, School of Chemical, Environmental and Mining Engineering, Coal Technology Research Group

2003-10-01

In this study, char image analysis techniques have been employed to investigate the morphology of chars obtained from a Drop-Tube furnace. Char image analysis results have been incorporated as inputs to a char burnout model based on Hurt's CBK model. It has been observed that the char combustion rate was strongly affected by char structural parameters and the inclusion of char morphology has led to a better prediction of char burnout. It has also been suggested by the model that the inclusion of ash inhibition overestimates the resistance attributed by ash film and the consideration of ash film resistance should be undertaken in a different way to give a better prediction at the later stages of char combustion. 12 refs., 13 figs., 5 tabs.

Alternative High Performance Polymers for Ablative Thermal Protection Systems

Science.gov (United States)

Boghozian, Tane; Stackpoole, Mairead; Gonzales, Greg

2015-01-01

Ablative thermal protection systems are commonly used as protection from the intense heat during re-entry of a space vehicle and have been used successfully on many missions including Stardust and Mars Science Laboratory both of which used PICA - a phenolic based ablator. Historically, phenolic resin has served as the ablative polymer for many TPS systems. However, it has limitations in both processing and properties such as char yield, glass transition temperature and char stability. Therefore alternative high performance polymers are being considered including cyanate ester resin, polyimide, and polybenzoxazine. Thermal and mechanical properties of these resin systems were characterized and compared with phenolic resin.

Evaluation of the Compressive Strength of Cement-Spent Resins Matrix Mixed with Bio char

International Nuclear Information System (INIS)

Zalina Laili; Muhamad Samudi Yasir; Zalina Laili; Mohd Abdul Wahab; Nur Azna Mahmud; Nurfazlina Zainal Abidin

2015-01-01

The evaluation of compressive strength of cement-spent resins matrix mixed with bio char was investigated. In this study, bio char with different percentage (5 %, 8 %, 11 % 14 % and 18 %) was used as alternative admixture material for cement solidification of spent resins. Some properties of the physical and chemical of spent resins and bio char were also investigated. The performance of cemented spent resins with the addition of bio char was evaluated based on their compressive strength and the water resistance test. The compressive strength was evaluated at three different curing periods of 7, 14 and 28 days, while 4 weeks of immersion in distilled water was chosen for water resistance test. The result indicated that the compressive strength at 7, 14 and 28 days of curing periods were above the minimum criterion for example > 3.45 MPa of acceptable level for cemented waste form. Statistical analysis showed that there was no significant relationship between the compressive strength of the specimen and the percentage of bio char content. Result from the water resistance test showed that only one specimen that contained of 5 % of bio char failed the water resistance test due to the high of spent resins/ bio char ratio. The compressive strength of cement solidified spent resins was found increased after the water resistance test indicating further hydration occurred after immersed in water. The results of this study also suggest that the specimen with 8 %, 11 %, 14 % and 18 % of bio char content were resistance in water and suitable for the leaching study of radionuclides from cement-bio char-spent resins matrix. (author)

Exploring novel silicon-containing polymers---From preceramic polymers to conducting polymers with nonlinear optical properties

Energy Technology Data Exchange (ETDEWEB)

Pang, Yi.

1991-10-07

Several new types of silicon-containing preceramic polymers, i.e., poly(diorganosilacetylene) and poly(diorganosilvinylene) have been synthesized with molecular weights from 10,000 to 120,000. These polymers could be thermally converted to SiC with a moderate to high char yields. Ready solubility and good processability made these types of polymers attractive in their applications to ceramics. The thermal polymerization of diethynyldiphenyl-silane, which was reported in 1968 to afford poly(diphenylsilyldiacetylene) via dehydrogenation, was reinvestigated. Spectroscopic studies showed that the polymer had a structure of polyacetylene type not diacetylene. Diphenyldiethynylgermane and a series of diorganodiethynylsilances were synthesized. These could be polymerized in the presence of MoCl{sub 5} or WCl{sub 6} to afford a soluble, violet material with Mw as high as 108,000. 100 refs., 56 figs., 16 tabs.

Preparation and characterization of high performance Schiff-base liquid crystal diepoxide polymer

International Nuclear Information System (INIS)

Liu Huan; Fu Zien; Xu Kai; Cai Hualun; Liu Xin; Chen Mingcai

2012-01-01

Graphical abstract: The specific effects of highly conjugated Schiff-base moiety on thermal properties of the Schiff-base epoxy polymer were proposed first by us. From the point of view of structure-properties relationship, it can be considered that owing to the presence of the Schiff-base group, the high performance liquid crystal diepoxide polymer displayed improved thermal stability. Highlights: ► In this work, we first proposed that specific effects of highly conjugated Schiff-base moiety on thermal properties of the Schiff-base epoxy polymer. ► As one aim of this study, the thermal and thermal-oxidative stabilities of the thermosets were studied by TGA under nitrogen and under air. ► The second aim of this study was to further understand the thermal degradation mechanism. ► For thermal degradation mechanism of this polymer under nitrogen, TG-IR was used to investigate volatile components, and SEM/EDS was used to explore morphologies and chemical components of the residual char. ► From the point of view of structure-properties relationship, it can be considered that owing to the presence of the Schiff-base group, the high performance liquid crystal diepoxide polymer displayed the improved thermal stability. - Abstract: A novel Schiff-base liquid crystal diepoxide polymer was prepared via a thermal copolymerization of a Schiff-base epoxy monomer (PBMBA) with a diamine co-monomer (MDA). We first proposed that specific effects of highly conjugated Schiff-base moiety on thermal properties of the Schiff-base epoxy polymer (PBMBA/MDA). Thermal degradation behavior of the polymer was characterized using thermogravimetric analysis (TGA) under nitrogen and under air, respectively. Thermogravimetric data obtained from TGA under nitrogen and under air reveal that PBMBA/MDA exhibits higher thermal stability compared with bisphenol-A type epoxy polymer (DGEBA/MDA) and other mesogene-containing epoxy polymer. It is worth pointing out that the outstanding residual

Pyrolysis of flax straw: Characterization of char, liquid, and gas as fuel

Science.gov (United States)

Tushar, Mohammad Shahed Hasan Khan

The demand for energy continues to outstrip its supply and necessitates the development of renewable energy options. Biomass has been recognized as a major renewable energy source to supplement the declining fossil fuel source of energy. It is the most popular form of renewable energy and, currently, biofuel production is becoming more promising. Being carbon neutral, readily available, and low in sulphur content makes biomass a very promising source of renewable energy. In the present research, both the isothermal and non-isothermal pressurized pyrolysis of flax straw is studied for the first time. In case of isothermal pyrolysis, the influence of pyrolysis temperature and reaction time on char yield and morphology was investigated. The applied pyrolysis temperature was varied between 300 and 500°C. The reaction time was varied from 15 to 60 min. The char yield was found to decrease as pyrolysis temperature and reaction time increased. The char structure and surface morphology were thoroughly investigated by means of x-ray diffraction (XRD), temperature-programmed oxidation (TPO), and scanning electron microscopy (SEM). The degree of porosity and graphitization increased as pyrolysis temperature and time increased. In fact, the experiment performed at 500°C for 1h duration did not yield any char; only residual ash could be obtained. The TPO studies on the char samples corroborated the XRD findings and showed the presence of two types of carbon, namely, amorphous filamentous carbon and graphitic carbon. A thermogravimetric analysis (TGA) of the char was performed to gain an understanding of combustion kinetics and reactivity. It implied that the reactivity of the char decreases as temperature increases, and this finding is well supported by the TPO, TGA, SEM, and XRD characterization data. Furthermore, an empirical global model was devised based on the power law to estimate activation energy and other kinetic parameters. For the non-isothermal pressurized

Ash liberation from included minerals during combustion of pulverized coal: the relationship with char structure and burnout

Energy Technology Data Exchange (ETDEWEB)

Wu, H.; Wall, T.; Liu, G.; Bryant, G. [University of Newcastle, Callaghan, NSW (Australia). CRC for Black Coal Utilization and Dept. of Chemical Engineering

1999-12-01

In this study, the float fraction ({lt} specific gravity of 2.0) of a size cut (63-90 {mu}m) bituminous coal was combusted in a drop tube furnace (DTF) at a gas temperature of 1300{degree}C under an atmosphere of air, to investigate the ash liberation at five coal burnoff levels (35.5%, 54.3%, 70.1%, 87.1% and 95.6%). The data indicated that char structure determines the ash liberation at different burnoff levels. Fragmentation of porous char was found to be the determinative mechanism for formation of fine ash during the early and middle stages of char combustion, while coalescence of included mineral matter determines the coarse ash formed in the later stages of combustion. The investigation confirmed that the char morphology and structure play a key role in determining char fragmentation, char burnout history, and the ash liberation during combustion. 35 refs., 5 figs., 2 tabs.

Degradation of p-Nitrophenol by Lignin and Cellulose Chars: H2O2-Mediated Reaction and Direct Reaction with the Char.

Science.gov (United States)

Yang, Jing; Pignatello, Joseph J; Pan, Bo; Xing, Baoshan

2017-08-15

Chars and other black carbons are reactive toward certain compounds. Such reactivity has been attributed to reduction of O 2 by persistent free radicals in the solid to H 2 O 2 , which then back-reacts with the solid to generate reactive oxygen species (ROS; especially HO • ). We studied the decomposition of p-nitrophenol (PNP) by pure lignin and cellulose chars aged in moist air or a vacuum at room temperature for up to a month. In air, the chars chemisorbed oxygen, a portion of which was liberated as H 2 O 2 when the char was submerged in water. The evolved H 2 O 2 was simultaneously decomposed by the char. PNP reacted predominantly in the sorbed state and only reduction products (phenol, catechol) were identified. Aging the char in air sharply (within hours) reduced H 2 O 2 -producing capacity and free radical concentration, but more gradually reduced PNP decay rate over the month-long period. PNP decay was only modestly suppressed (12-30%) by H 2 O 2 removal (catalase), and had little effect on the free radical signal (reactive sites. Lignin char was generally more reactive than cellulose char. The Fe impurity in lignin played no role. The results are relevant to the fate of pollutants in black carbon-rich environments and the use of carbons in remediation.

Gasification of biomass chars in steam-nitrogen mixture

International Nuclear Information System (INIS)

Haykiri-Acma, H.; Yaman, S.; Kucukbayrak, S.

2006-01-01

Some agricultural and waste biomass samples such as sunflower shell, pinecone, rapeseed, cotton refuse and olive refuse were first pyrolyzed in nitrogen, and then, their chars were gasified in a gas mixture of steam and nitrogen. Experiments were performed using the thermogravimetric analysis technique. Pyrolysis of the biomass samples was performed at a heating rate of 20 K/min from ambient to 1273 K in a dynamic nitrogen atmosphere of 40 cm 3 min -1 . The obtained chars were cooled to ambient temperature and then gasified up to 1273 K in a dynamic atmosphere of 40 cm 3 min -1 of a mixture of steam and nitrogen. Derivative thermogravimetric analysis profiles from gasification of the chars were derived, and the mass losses from the chars were interpreted in terms of temperature. It was concluded that gasification characteristics of biomass chars were fairly dependent on the biomass properties such as ash and fixed carbon contents and the constituents present in the ash. Different mechanisms in the three temperature intervals, namely water desorption at lower temperatures, decomposition of hydroxide minerals to oxide minerals and formation of carbon monoxide at medium temperatures and production of hydrogen at high temperatures govern the behavior of the char during the gasification process. The chars from pinecone and sunflower shell could be easily gasified under the mentioned conditions. In order to further raise the conversion yields, long hold times should be applied at high temperatures. However, the chars from rapeseed and olive refuse were not gasified satisfactorily. Low ash content and high fixed carbon content biomass materials are recommended for use in gasification processes when char from pyrolysis at elevated temperatures is used as a feedstock

A burnout prediction model based around char morphology

Energy Technology Data Exchange (ETDEWEB)

Tao Wu; Edward Lester; Michael Cloke [University of Nottingham, Nottingham (United Kingdom). School of Chemical, Environmental and Mining Engineering

2006-05-15

Several combustion models have been developed that can make predictions about coal burnout and burnout potential. Most of these kinetic models require standard parameters such as volatile content and particle size to make a burnout prediction. This article presents a new model called the char burnout (ChB) model, which also uses detailed information about char morphology in its prediction. The input data to the model is based on information derived from two different image analysis techniques. One technique generates characterization data from real char samples, and the other predicts char types based on characterization data from image analysis of coal particles. The pyrolyzed chars in this study were created in a drop tube furnace operating at 1300{sup o}C, 200 ms, and 1% oxygen. Modeling results were compared with a different carbon burnout kinetic model as well as the actual burnout data from refiring the same chars in a drop tube furnace operating at 1300{sup o}C, 5% oxygen, and residence times of 200, 400, and 600 ms. A good agreement between ChB model and experimental data indicates that the inclusion of char morphology in combustion models could well improve model predictions. 38 refs., 5 figs., 6 tabs.

The catalytic cracking mechanism of lignite pyrolysis char on tar

International Nuclear Information System (INIS)

Lei, Z.; Huibin, H.; Xiangling, S.; Zhenhua, M.; Lei, Z.

2017-01-01

The influence of different pyrolysis conditions for tar catalytic cracking will be analyzed according to the lignite pyrolysis char as catalyst on pyrolytic tar in this paper. The pyrolysis char what is the by-product of the cracking of coal has an abundant of pore structure and it has good catalytic activity. On this basis, making the modified catalyst when the pyrolysis char is activation and loads Fe by impregnation method. The cracking mechanism of lignite pyrolytic tar is explored by applying gas chromatograph to analyze splitting products of tar. The experimental results showed that: (1) The effect of tar cracking as the pyrolysis temperature, the heating rate, the volatilization of pyrolysis char and particle size increasing is better and better. The effect of the catalytic and cracking of lignite pyrolysis char in tar is best when the heating rate, the pyrolysis temperature, the volatiles of pyrolysis char, particle size is in specific conditions.(2) The activation of pyrolysis char can improve the catalytic effect of pyrolysis char on the tar cracking. But it reduces the effect of the tar cracking when the pyrolysis char is activation loading Fe. (author)

Synthesis and characterization of resorcinol–formaldehyde resin chars doped by zinc oxide

International Nuclear Information System (INIS)

Gun’ko, Vladimir M.; Bogatyrov, Viktor M.; Oranska, Olena I.; Urubkov, Iliya V.; Leboda, Roman; Charmas, Barbara; Skubiszewska-Zięba, Jadwiga

2014-01-01

Polycondensation polymerization of resorcinol–formaldehyde (RF) mixtures in water with addition of different amounts of zinc acetate and then carbonization of dried gels are studied to prepare ZnO doped chars. Zinc acetate as a catalyst of resorcinol–formaldehyde polycondensation affects structural features of the RF resin (RFR) and, therefore, the texture of chars prepared from Zn-doped RFR. The ZnO doped chars are characterized using thermogravimetry, low temperature nitrogen adsorption/desorption, Raman spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), and high resolution transmission electron microscopy (HRTEM). At a relatively high content of zinc acetate (1 mol per 10–40 mol of resorcinol) in the reaction mixture, the formation of crystallites of ZnO (zincite) occurs in a shape of straight nanorods of 20–130 nm in diameter and 1–3 μm in length. At a small content of zinc acetate (1 mol per 100–500 mol of resorcinol), ZnO in composites is XRD amorphous and does not form individual particles. The ZnO doped chars are pure nanoporous at a minimal ZnO content and nano-mesoporous or nano-meso-macroporous at a higher ZnO content.

Carbon distribution in char residue from gasification of kraft black liquor

International Nuclear Information System (INIS)

Sricharoenchaikul, Viboon; Frederick, W.J.; Agrawal, Pradeep

2003-01-01

The char residue yields and the total carbon and carbonate content were measured for dry black liquor solids after pyrolysis or gasification in a laminar entrained-flow reactor. The experimental conditions were 700-1000 deg. C in N 2 ,CO 2 /N 2 or water vapor/N 2 at 1 bar total pressure, for residence times from 0.3 to 1.7 s. Fixed carbon yields, when measured at the same particle residence time, decreased with increasing reactor temperature. CO 2 and water vapor diminished the char carbon significantly at temperatures above 800 deg. C, compared with pyrolysis in N 2 . Water vapor oxidized the char carbon more rapidly than did CO 2 . At 1000 deg. C, the reactions of carbon with sulfate and carbonate became faster, resulting in a smaller difference between carbon conversion rates in the different gas environments. By the end of devolatilization, the amount of carbonate in the char had changed very little at 700-800 deg. C. After devolatilization, carbonate was formed more rapidly at higher temperatures. The presence of CO 2 or water vapor increased the formation of carbonate. In the presence of these gases, more carbonate was measured at all temperatures and residence times. The maximum carbonate measured in the char was 16% of the carbon in the black liquor solids, as compared to 4.4% in the original dry liquor solids. Under most conditions, the carbonate, as a fraction of carbon input, first increased to a constant, temperature-independent value and then decreased

Sulfate reduction and carbon removal during kraft char burning

Energy Technology Data Exchange (ETDEWEB)

Waag, K.J.; Frederick, W.J.; Sricharoenchaikul, V [Oregon State Univ., Corvallis, OR (United States). Dept. of Chemical Engineering; Grace, T.M. [T.M. Grace Company, Appleton, WI (United States); Kymalainen, M. [Tampella Power, Tampere (Finland)

1995-12-31

An improved mathematical model of char burning during black liquor combustion was described. Enhancements include a proper treatment of CO{sub 2} and H{sub 2}O gasification, reactions between oxygen and combustibles in the boundary layer, and integration of sulfate reduction and sulfide reoxidation into the char burning process. Gasification of char carbon by reaction with H{sub 2}O and CO{sub 2} proved to be the most important means of carbon release under typical recovery furnace conditions. Sulfate reduction was shown to be responsible for only a minor part of the carbon release. Simulations showed that for typical recovery boiler conditions, char burning behavior is independent of oxygen concentration up to the point of carbon depletion. After carbon depletion, sulfide reoxidation occurs at a rate determined by oxygen mass transfer. Process variables that had the biggest effect on char burning behavior were initial black liquor drop diameter and temperature; also there was a direct link between char burnout times and the amount of sulfate reduction. At a given temperature, any variable that shortened the char burnout time resulted in proportionately less reduction. 22 refs., 10 figs., 2 tabs.

MLKL forms disulfide bond-dependent amyloid-like polymers to induce necroptosis.

Science.gov (United States)

Liu, Shuzhen; Liu, Hua; Johnston, Andrea; Hanna-Addams, Sarah; Reynoso, Eduardo; Xiang, Yougui; Wang, Zhigao

2017-09-05

Mixed-lineage kinase domain-like protein (MLKL) is essential for TNF-α-induced necroptosis. How MLKL promotes cell death is still under debate. Here we report that MLKL forms SDS-resistant, disulfide bond-dependent polymers during necroptosis in both human and mouse cells. MLKL polymers are independent of receptor-interacting protein kinase 1 and 3 (RIPK1/RIPK3) fibers. Large MLKL polymers are more than 2 million Da and are resistant to proteinase K digestion. MLKL polymers are fibers 5 nm in diameter under electron microscopy. Furthermore, the recombinant N-terminal domain of MLKL forms amyloid-like fibers and binds Congo red dye. MLKL mutants that cannot form polymers also fail to induce necroptosis efficiently. Finally, the compound necrosulfonamide conjugates cysteine 86 of human MLKL and blocks MLKL polymer formation and subsequent cell death. These results demonstrate that disulfide bond-dependent, amyloid-like MLKL polymers are necessary and sufficient to induce necroptosis.

Controls upon biomass losses and char production from prescribed burning on UK moorland.

Science.gov (United States)

Worrall, Fred; Clay, Gareth D; May, Richard

2013-05-15

Prescribed burning is a common management technique used across many areas of the UK uplands. However, there are few data sets that assess the loss of biomass during burning and even fewer data on the effect of burning on above-ground carbon stocks and production of char. During fire the production of char occurs which represents a transfer of carbon from the short term bio-atmospheric cycle to the longer term geological cycle. However, biomass is consumed leading to the reduction in litter formation which is the principal mechanism for peat formation. This study aims to solve the problem of whether loss of biomass during a fire is ever outweighed by the production of refractory forms of carbon during the fire. This study combines both a laboratory study of char production with an assessment of biomass loss from a series of field burns from moorland in the Peak District, UK. The laboratory results show that there are significant effects due to ambient temperature but the most important control on dry mass loss is the maximum burn temperature. Burn temperature was also found to be linearly related to the production of char in the burn products. Optimisation of dry mass loss, char production and carbon content shows that the production of char from certain fires could store more carbon in the ecosystem than if there had been no fire. Field results show that approximately 75% of the biomass and carbon were lost through combustion, a figure comparable to other studies of prescribed fire in other settings. Char-C production was approximately 2.6% of the carbon consumed during the fire. This study has shown that there are conditions (fast burns at high temperatures) under which prescribed fire may increase C sequestration through char production and that these conditions are within existing management options available to practitioners. Copyright © 2013 Elsevier Ltd. All rights reserved.

Method of forming electronically conducting polymers on conducting and nonconducting substrates

Science.gov (United States)

Murphy, Oliver J. (Inventor); Hitchens, G. Duncan (Inventor); Hodko, Dalibor (Inventor); Clarke, Eric T. (Inventor); Miller, David L. (Inventor); Parker, Donald L. (Inventor)

2001-01-01

The present invention provides electronically conducting polymer films formed from photosensitive formulations of pyrrole and an electron acceptor that have been selectively exposed to UV light, laser light, or electron beams. The formulations may include photoinitiators, flexibilizers, solvents and the like. These solutions can be used in applications including printed circuit boards and through-hole plating and enable direct metallization processes on non-conducting substrates. After forming the conductive polymer patterns, a printed wiring board can be formed by sensitizing the polymer with palladium and electrolytically depositing copper.

A Study on Recycling of Spent Mushroom Substrate to Prepare Chars and Activated Carbon

Directory of Open Access Journals (Sweden)

Yuhui Ma

2014-05-01

Full Text Available Chars were obtained from spent mushroom substrate (SMS via pyrolysis. It was found that as the pyrolysis temperature increased from 400 to 700 °C, the char yield decreased from 45.10 to 33.79 wt.% and the higher heating value increased from 17.32 to 22.72 MJ/kg. The largest BET surface area (13 m2/g was created at 500 °C. Hydrogen atoms were continuously lost during pyrolysis, whereas oxygen atoms were difficult to eliminate. Whewellite, calcite, lime, and quartz were the minerals in the chars, and their forms and crystallinity changed with changing pyrolysis temperature. Activated carbon with a BET surface area of 1023 m2/g and a total pore volume of 0.595 cm3/g was obtained from the char prepared at 500 °C. Its characteristics were studied by N2-adsorption, Fourier transform infrared spectroscopy (FTIR, and X-ray diffraction (XRD. The pyrolysis and KOH-activation processes were investigated by thermogravimetric analysis (TGA. The results showed that the pyrolysis of SMS occurred primarily between 217 and 375 °C and that the energies needed for the pyrolysis reactions were relatively low due to the prior mushroom cultivation. Furthermore, lignin was incompletely decomposed in the char prepared at 500 °C, and KOH suppressed tar evolution and reduced the energy needed to decompose the residual lignin during activation.

Toxicity of pyrolysis gases from some cellular polymers

Science.gov (United States)

Hilado, C. J.; Machado, A. M.

1978-01-01

Various samples of cellular polymers were evaluated for toxicity of pyrolysis gases, using the screening test method developed at the University of San Francisco. The cellular polymer samples included polyimide, polymethacrylimide, polybismaleimide, polyurethane, polyisocyanurate, polyethylene, polychloroprene, polyvinyl chloride, polystyrene, polysiloxane, and polyphosphazene. The cellular polymers exhibited varying levels of toxicity under these test conditions. Among the rigid cellular polymers, times to death were shortest with the imide type foams and longest with polyvinyl chloride and polystyrene. Among the flexible cellular polymers, times to death were shortest with polyimide and polyester, and longest with polychloroprene and polysiloxane. Increased char yield was not necessarily associated with reduced toxicity.

Combustion reactivity of chars from copyrolysis of coal with coke-oven gas

Energy Technology Data Exchange (ETDEWEB)

Liao Hongqiang; Sun Chenggong; Li Baoqing [Chinese Academy of Sciences, Taiyuan (China). State Key Lab. of Coal Conversion

1997-12-31

The combustion reactivity of char from pyrolysis of Xianfeng lignite with coke-oven gas (COG) is related to the pyrolysis pressure and heating rate. Decreasing pressure and increasing heating rate enhance the char yields and combustion reactivity. The combustion reactivities of char from coal pyrolysis with COG nearly reach to that of char from hydropyrolysis, but lower than those of char from coal pyrolysis under N{sub 2}. (orig.)

Nitric oxide reduction over a synthetic coal char

Energy Technology Data Exchange (ETDEWEB)

C. Pevida; A. Arenillas; F. Rubiera; J.J. Pis [Instituto Nacional del Carbon, CSIC, Oviedo (Spain)

2003-07-01

In the present work, the mechanisms involved in the NO heterogeneous reduction have been investigated. A synthetic coal char was used as the carbon source. This synthetic coal was made from a mixture of model compounds and provides well-known functionalities, including nitrogenated ones, similar to those found in a high volatile bituminous coal. The char was obtained by pyrolysis of the synthetic coal, up to 1123 K, under helium atmosphere in a fixed bed reactor. Char texture and structure were characterised by N{sub 2} and CO{sub 2} adsorption isotherms at 77 and 273 K, respectively, X-ray diffraction, immersion calorimetry in C{sub 6}H{sub 6} and scanning electron microscopy (SEM). Temperature programmed reactions (TPR) were carried out in a thermogravimetric analyser using 400 ppm NO diluted in Ar as the reactant gas. The char was heated at 15 K min{sup -1} from room temperature to 1273 K. Gaseous products were simultaneously analysed by mass spectrometry (MS) and Fourier transform infrared spectroscopy (FTIR). The influence of nitrogen in the solid phase on the reduction mechanism was evaluated by comparing the results for chars with and without nitrogen in their composition. The results of this preliminary study showed that the presence of nitrogen in the chars composition did not favour the heterogeneous NO reduction. In addition, low temperature NO chemisorption on the carbon surface creates complexes that take an active part in the subsequent reactions with NO. 5 refs., 4 figs., 3 tabs.

Production of activated char from Illinois coal for flue gas cleanup

Science.gov (United States)

Lizzio, A.A.; DeBarr, J.A.; Kruse, C.W.

1997-01-01

Activated chars were produced from Illinois coal and tested in several flue gas cleanup applications. High-activity chars that showed excellent potential for both SO2 and NOx removal were prepared from an Illinois No. 2 bituminous coal. The SO2 (120 ??C) and NOx (25 ??C) removal performance of one char compared favorably with that of a commercial activated carbon (Calgon Centaur). The NOx removal performance of the same char at 120 ??C exceeded that of the Centaur carbon by more than 1 order of magnitude. Novel char preparation methods were developed including oxidation/thermal desorption and hydrogen treatments, which increased and preserved, respectively, the active sites for SO2 and NOx adsorption. The results of combined SO2/NOx removal tests, however, suggest that SO2 and NOx compete for similar adsorption sites and SO2 seems to be more strongly adsorbed than NO. A low-activity, low-cost char was also developed for cleanup of incinerator flue gas. A three-step method involving coal preoxidation, pyrolysis, and CO2 activation was used to produce the char from Illinois coal. Five hundred pounds of the char was tested on a slipstream of flue gas from a commercial incinerator in Germany. The char was effective in removing >97% of the dioxins and furans present in the flue gas; mercury levels were below detectable limits.

Plastic scintillators based on polymers with eliminated excimer forming

Energy Technology Data Exchange (ETDEWEB)

Adadurov, A.F., E-mail: adadurov@isma.kharkov.u [Institute for Scintillating Materials NAN of Ukraine, 60 Lenin Ave, 61001 Kharkov (Ukraine); Yelyseev, D.A.; Titskaya, V.D.; Lebedev, V.N.; Zhmurin, P.N. [Institute for Scintillating Materials NAN of Ukraine, 60 Lenin Ave, 61001 Kharkov (Ukraine)

2011-05-15

Plastic scintillators (PS) were made based on benzyl methacrylate and methyl-methacrylate P(BzMA + MMA) copolymer in which the excimer forming rate is by two order lesser than that in polystyrene-based polymer matrix. Studying of these PS light yield demonstrates the importance of migration processes comparing to excimer formation. It is found that to obtain PS with high scintillation efficiency it is necessary to use the polymer base (matrix) in which excimer forming is eliminated but the migration process along the chromophores is maximally favored. To explain the accelerated energy transfer between phenyl chromophores it is proposed to use a mechanism of exchange of that virtual excitons that can propagate along a one-dimensional back-bone of polymer molecule. Clearing the details of mechanism of interaction between chromophores of polymer molecules which is responsible for accelerated radiationless energy transfer enable will determine in future the way of effective plastic scintillators designing.

Nitroxide radicals formed in situ as polymer chain growth regulators

International Nuclear Information System (INIS)

Kolyakina, Elena V; Grishin, Dmitry F

2009-01-01

Published data on controlled synthesis of macromolecules using nitroxide radicals, formed in situ during polymerization, as polymer chain growth regulators are systematized and generalized. The attention is focused on the mechanism of polymer chain growth control during reversibly inhibited radical homopolymerization and the effect of structure of precursors and regulating additives on the polymerization kinetics of monomers of different nature and the molecular-mass characteristics of the polymers thus formed. The key methods for generation of nitroxide radicals directly during polymerization are considered. The prospects for development and practical use of these approaches for the synthesis of new polymeric materials are evaluated.

Ultrasonically assisted extraction of calcium and ash from char

Science.gov (United States)

Mathumba, E. E.; Mbaya, R. K. K.; Kolesnikov, A.

2018-03-01

This study characterized and removed calcium and ash content from char to improve the chemical quality of char as reductant for titanium smelting application. Calcium in char can be classified in two parts: mineral matter and cationic metals associated with organic matrix. Virgin and chemically treated char was characterized by using ISO 1171, wet chemistry methods, ISO 19579, XRF, and B.E.T. methods. In this present work, demineralization of char with mild chemical leachants such as acetic acid, citric acid, gluconic acid and Ethylene Diamine Tetra Acetic acid with three different ultrasonic power input (150 W, 270 W and 300 W) and semi-dual frequency of 40 kHz tank was investigated. Actual power dissipated into the system was calculated from the calorimetric measurement. An optimum set of process parameters are identified and validated. The ultrasound technology was compared with soaking technology to determine the efficiency of ultrasound system for the removal of calcium. The removal of calcium was exponentially higher with ultrasonic treatment than without it. Results revealed that mild chemical reagents do not harm the carbon content of char. It is evident from the results that amongst the leachants used; acetic and citric acid has caused significant removal of mineral phases.

Influence of char structure on reactivity and nitric oxide emissions

Energy Technology Data Exchange (ETDEWEB)

Arenillas, Ana; Rubiera, Fernando; Parra, Jose B.; Pis, Jose J. [Department of Energy and Environment, Instituto Nacional del Carbon, CSIC, Apartado 73, 33080 Oviedo (Spain)

2002-06-20

The aim of this study was to investigate the influence of coal rank and operating conditions during coal pyrolysis on the resultant char texture properties, morphology and reactivity. A range of bituminous coals were pyrolysed in a fixed bed reactor at different heating rates. It was found that the higher the heating rate and the lower the coal rank, the more microporous chars were obtained. Isothermal (500 C) gasification in 20% oxygen in argon of the chars was carried out using a differential thermogravimetric system (DTG). The results of this work indicated that the increase in the availability of char-active surface sites led to an increase in char reactivity, not only for oxygen but also for other reactive gases, in particular NO, diminishing emissions during the combustion process.

Coal pyrolysis and char burnout under conventional and oxy-fuel conditions

Energy Technology Data Exchange (ETDEWEB)

Al-Makhadmeh, L.; Maier, J.; Scheffknecht, G. [Stuttgart Univ. (Germany). Institut fuer Verfahrenstechnik und Dampfkesselwesen

2009-07-01

Coal utilization processes such as combustion or gasification generally involve several steps i.e., the devolatilization of organic materials, homogeneous reactions of volatile matter with the reactant gases, and heterogeneous reactions of the solid (char) with the reactant gases. Most of the reported work about coal pyrolysis and char burnout were performed at low temperatures under environmental conditions related to the air firing process with single particle tests. In this work, coal combustion under oxy-fuel conditions is investigated by studying coal pyrolysis and char combustion separately in practical scales, with the emphasis on improving the understanding of the effect of a CO{sub 2}-rich gas environment on coal pyrolysis and char burnout. Two coals, Klein Kopje a medium volatile bituminous coal and a low-rank coal, Lausitz coal were used. Coal pyrolysis in CO{sub 2} and N{sub 2} environments were performed for both coals at different temperatures in an entrained flow reactor. Overall mass release, pyrolysis gas concentrations, and char characterization were performed. For char characterization ultimate analysis, particle size, and BET surface area were measured. Chars for both coals were collected at 1150 C in both CO{sub 2} and N{sub 2} environments. Char combustion was performed in a once-through 20 kW test facility in O{sub 2}/CO{sub 2} and O{sub 2}/N{sub 2} atmospheres. Besides coal quality, oxygen partial pressure was chosen as a variable to study the effect of the gas environment on char burnout. In general, it is found that the CO{sub 2} environment and coal rank have a significant effect on coal pyrolysis and char burnout. (orig.)

Attrition-free pyrolysis to produce bio-oil and char.

Science.gov (United States)

Mauviel, Guillain; Guillain, Mauviel; Kies, Fairouz; Fairouz, Kies; René, Mar Sans; Mar, Sans Rene; Ferrer, Monique; Monique, Ferrer; Lédé, Jacques; Jacques, Lédé

2009-12-01

Experiments are performed on a laboratory scale setup where beech wood chips are heated by gas convection and walls radiation. This study shows that it is possible to obtain high bio-oil and char yields with relatively low external heat transfer coefficients. The main advantage of this convection/radiation heat transfer mode compared to solid-solid collisions, applied in fluidized bed or twin screw reactors, is the reduction of solid attrition (char and sand). Thus tricky gas-solid separation through hot cyclones and/or hot filters could be avoided or reduced. It should be possible to recover directly bio-oil with less char particles and char free of sand dust. These qualities would allow easier use of these bio-products in different applications.

A study on the char burnout characteristics of coal and biomass blends

Energy Technology Data Exchange (ETDEWEB)

Behdad Moghtaderi [University of Newcastle, Callaghan, NSW (Australia). Discipline of Chemical Engineering, School of Engineering, Faculty of Engineering and Built Environment

2007-10-15

The char burnout characteristics of coal/biomass blends under conditions pertinent to pulverised fuel combustors were investigated by a combined modelling and experimental approach. Results indicate that blending of coal with biomass increases the likelihood of char extinction (i.e. extinction potential of the char particle in the blend), in turn, decreasing the char burnout level. Our modelling results attribute this to a reduction in the char particle size to levels below a critical dimension which appears to be a strong function of the fuel blending ratio (the weight percentage of biomass in the blend), fuel reactivity, char cloud shape and particle density number. It is demonstrated here that the drop in the char burnout level during co-firing can be effectively resolved when a more reactive secondary coal is added to the blend to minimise its extinction potential. 22 refs., 8 figs., 2 tabs.

Intrinsic char reactivity of plastic waste (PET) during CO2 gasification

International Nuclear Information System (INIS)

Gil, M.V.; Fermoso, J.; Pevida, C.; Pis, J.J.; Rubiera, F.

2010-01-01

Char reactivity has a strong influence on the gasification process, since char gasification is the slowest step in the process. A sample of waste PET was devolatilised in a vertical quartz reactor and the resulting char was partially gasified under a CO 2 atmosphere at 925 C in order to obtain samples with different degrees of conversion. The reactivity of the char in CO 2 was determined by isothermal thermogravimetric analysis at different temperatures in a kinetically controlled regime and its reactive behaviour was evaluated by means of the random pore model (RPM). The texture of the char was characterised by means of N 2 and CO 2 adsorption isotherms. The results did not reveal any variation in char reactivity during conversion, whereas the micropore surface area was affected during the gasification process. It was found that the intrinsic reaction rate of the char can be satisfactorily calculated by normalizing the reaction rate by the narrow micropore surface area calculated from the CO 2 adsorption isotherms. It can be concluded therefore that the surface area available for the gasification process is the area corresponding to the narrow microporosity. (author)

Study on coal char ignition by radiant heat flux.

Science.gov (United States)

Korotkikh, A. G.; Slyusarskiy, K. V.

2017-11-01

The study on coal char ignition by CO2-continuous laser was carried out. The coal char samples of T-grade bituminous coal and 2B-grade lignite were studied via CO2-laser ignition setup. Ignition delay times were determined at ambient condition in heat flux density range 90-200 W/cm2. The average ignition delay time value for lignite samples were 2 times lower while this difference is larger in high heat flux region and lower in low heat flux region. The kinetic constants for overall oxidation reaction were determined using analytic solution of simplified one-dimensional heat transfer equation with radiant heat transfer boundary condition. The activation energy for lignite char was found to be less than it is for bituminous coal char by approximately 20 %.

Mercury adsorption of modified mulberry twig chars in a simulated flue gas.

Science.gov (United States)

Shu, Tong; Lu, Ping; He, Nan

2013-05-01

Mulberry twig chars were prepared by pyrolysis, steam activation and impregnation with H2O2, ZnCl2 and NaCl. Textural characteristics and surface functional groups were performed using nitrogen adsorption and FTIR, respectively. Mercury adsorption of different modified MT chars was investigated in a quartz fixed-bed absorber. The results indicated that steam activation and H2O2-impregnation can improve pore structure significantly and H2O2-impregnation and chloride-impregnation promote surface functional groups. However, chloride-impregnation has adverse effect on pore structure. Mercury adsorption capacities of impregnated MT chars with 10% or 30% H2O2 are 2.02 and 1.77 times of steam activated MT char, respectively. Mercury adsorption capacity of ZnCl2-impregnated MT char increase with increasing ZnCl2 content and is better than that of NaCl-impregnated MT char at the same chloride content. The modified MT char (MT873-A-Z5) prepared by steam activation following impregnation with 5% ZnCl2 exhibits a higher mercury adsorption capacity (29.55 μg g(-1)) than any other MT chars. Copyright © 2013 Elsevier Ltd. All rights reserved.

Physico-Chemical Characterizations of Sawdust-Derived Bio char as Potential Solid Fuels

International Nuclear Information System (INIS)

Wan Azlina Wan Ab Karim Ghani

2014-01-01

Characterization Malaysian rubber-wood sawdust derived bio char (MRWSB) produced in the fixed bed pyrolysis under different temperatures (450 to 850 degree Celsius) were studied for its applicability as a solid fuel. A range of analyses were carried out, including bio char oxidation reactivity , inorganic species, oxygen and hydrogen contents in the bio chars, release of heteroatoms in bio char as the gaseous product, and bio char structural evolution during pyrolysis process. The results show that the optimum temperature for carbonization to obtain a char having moderately high yield was found as 450 degree Celsius. Thermogravimetric analyses (TG) shows that temperatures induces a progressively more ordered carbonaceous structure and leads to a significant changes in the bio char reactivity. The process is coupled with the loss of heteroatoms, released as dominantly carbon dioxide (C0 2 ) and carbon dioxide (CO). In addition, the elemental study of wood-derived bio char shows the higher carbon content but with low H/C and 0/C ratio suggested this material was dominated by highly aromatic structures and this were revealed in the Fourier transform infra-red (FTIR). More importantly, insignificant amount of inorganic species is evidenced in the samples. (author)

Influence of pyrolysis conditions on the structure and gasification reactivity of biomass chars

Energy Technology Data Exchange (ETDEWEB)

E. Cetin; B. Moghtaderi; R. Gupta; T.F. Wall [University of Newcastle, Callaghan, NSW (Australia). Discipline of Chemical Engineering, Faculty of Engineering and Built Environment, School of Engineering

2004-11-01

The physical and chemical structure as well as gasification reactivities of chars generated from several biomass species (i.e. pinus radiata, eucalyptus maculata and sugar cane bagasse) were studied to gain insight into the role of heating rate and pressure on the gasification characteristics of biomass chars. Char samples were generated in a suite of reactors including a wire mesh reactor, a tubular reactor, and a drop tube furnace. Scanning electron microscopy analysis, X-ray diffractometry, digital cinematography and surface area analysis were employed to determine the impact of operating conditions on the char structure. The global gasification reactivities of char samples were also determined for a range of pressures between 1 and 20 bar using pressurised thermogravimetric analysis technique. Char reactivities were found to increase with increasing pyrolysis heating rates and decreasing pyrolysis pressure. It was found that under high heating rates the char particles underwent plastic deformation (i.e. melted) developing a structure different to that of the virgin biomass. Pressure was also found to influence the physical and chemical structures of char particles. The difference in the gasification reactivities of biomass chars at pressure was found to correlate well with the effect of pyrolysis pressure on the graphitisation process in the biomass char structure. 29 refs., 18 figs., 2 tabs.

Fundamental study of the pulverized coal char combustion in oxyfuel mode with drop tube furnace

Energy Technology Data Exchange (ETDEWEB)

Ito, Takamasa; Takafuji, Makoto; Suda, Toshiyuki; Fujimori, Toshiro [Heat and Fluid Dynamics Department, Yokohama (Japan)

2013-07-01

The combustion characteristics of coal char particles in either O{sub 2}/N{sub 2} or O{sub 2}/CO{sub 2} conditions were experimentally investigated. Especially, the char burnout, the char particle temperature and the shrinkage of the char particles were discussed. A Drop Tube Furnace (DTF: whose wall temperature was set at 873, 923 and 973 K) was used as the experimental apparatus. The experimental results revealed that, in equivalent oxygen concentration, the char burnout and the char particle temperature were higher in O{sub 2}/N{sub 2} conditions than those in O{sub 2}/CO{sub 2} conditions. The shrinkage of the char particle did not show the large difference in either O{sub 2}/N{sub 2} or O{sub 2}/CO{sub 2} conditions. Up to 15% of char burnout, the char particle diameters were reduced gradually. Up to 80% of char burnout, the char particle diameters were not changed. This is supposed that the chemical reaction is mainly occurred not on the external surface but on the internal surface of the char particle. Over 80% of char burnout, sudden shrinkage could be seen. Finally, an empirical equation for the prediction of the char particle shrinkage was introduced. Further investigation is required in high operating temperature, where CO{sub 2} gasification may have a large influence on the char burnout.

Properties of gasification-derived char and its utilization for catalytic tar reforming

Science.gov (United States)

Qian, Kezhen

Char is a low-value byproduct of biomass gasification and pyrolysis with many potential applications, such as soil amendment and the synthesis of activated carbon. The overall goal of the proposed research was to develop novel methods to use char derived from gasification for high-value applications in syngas conditioning. The first objective was to investigate effects of gasification condition and feedstock on properties of char derived from fluidized bed gasification. Results show that the surface areas of most of the char were 1--10 m 2/g and increased as the equivalence ratio increased. Char moisture and fixed carbon contents decreased while ash content increased as equivalence ratio increased. The next objective was to study the properties of sorghum and red cedar char derived from downdraft gasifier. Red cedar char contained more aliphatic carbon and o-alkyl carbon than sorghum char. Char derived from downdraft gasification had higher heating values and lower ash contents than char derived from fluidized bed gasification. The gasification reactivity of red cedar char was higher than that of sorghum char. Then, red cedar char based catalysts were developed with different preparation method to reform toluene and naphthalene as model tars. The catalyst prepared with nickel nitrate was found to be better than that with nickel acetate. The nickel particle size of catalyst impregnated with nickel nitrate was smaller than that of catalyst impregnated with nickel acetate. The particle size of catalyst impregnated with nickel acetate decreased by hydrazine reduction. The catalyst impregnated with nickel nitrate had the highest toluene removal efficiency, which was 70%--100% at 600--800 °C. The presence of naphthalene in tar reduced the catalyst efficiency. The toluene conversion was 36--99% and the naphthalene conversion was 37%--93% at 700--900 °C. Finally, effects of atmosphere and pressure on catalytic reforming of lignin-derived tars over the developed catalyst

Synthesis and structural features of resorcinol–formaldehyde resin chars containing nickel nanoparticles

International Nuclear Information System (INIS)

Galaburda, M.V.; Bogatyrov, V.M.; Skubiszewska-Zięba, J.; Oranska, O.I.; Sternik, D.; Gun’ko, V.M.

2016-01-01

Graphical abstract: - Highlights: • Facile synthesis of the Ni-doped carbon sorbents via carbonization of resorcinol–formaldehyde polymers/nickel(II) acetate mixtures in the inert atmosphere. • Effects of Ni content, as well as water volume and temperature treatment on the morphology and texture of the chars. • Ni/C composites are characterized by a core–shell structure with well-crystallized graphitic shells. • Ni content influences the structure of the carbon. • Nickel-doped carbon nanocomposites were used as a magnetically separable adsorbent. - Abstract: A series of meso- and microporous carbons containing magnetic Ni nanoparticles (Ni/C) with a variety of Ni loadings were synthesized by a simple one-pot procedure through carbonization of resorcinol–formaldehyde polymers containing various amounts of nickel(II) acetate. Such composite materials were characterized by N_2 sorption, Raman spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM) and Transmission electron microscope (TEM). The XRD patterns reveal peaks corresponding to face centered cubic nickel with the average size of crystallites of 17–18 nm. SEM and TEM results reveal that the formation of the nanoparticles took place mainly in the carbon spheres (1–2 μm in size) and on the outer surface as well. The as-prepared composites are characterized by a core–shell structure with well-crystallized graphitic shells about 8–15 nm in thickness. The Raman spectra show that Ni content influences the structure of the carbon. It was also shown that the morphology (particle shape and sizes) and porosity (pore volume and pore size distribution) of the chars are strongly dependent on water and nickel contents in the blends. One of the applications of Ni/C was demonstrated as a magnetically separable adsorbent.

Comparison of char structural characteristics and reactivity during conventional air and oxy-fuel combustion

Energy Technology Data Exchange (ETDEWEB)

Liu, Xiaowei; Xu, Minghou; Yao, Hong; Gu, Ying; Si, Junping; Xiong, Chao [Huazhong Univ. of Science and Technology, Wuhan (China). State Key Lab. of Coal Combustion

2013-07-01

The capture and sequestration of CO{sub 2} generated from large- scale stationary power plants is considered to be one of the leading technologies that could potentially have a significant impact on reducing greenhouse emissions. Among these emerging technologies, the oxy-fuel combustion is a near-zero emission technology that can be adapted to both new and existing pulverized coal-fired power stations. The goal of this work is to make a comparative study on char structural characteristics (including char yield, swelling ratio, BET surface area, pore distribution, morphology) and reactivity during conventional air and oxy-fuel combustion. Specific experimental designs include two series. One is carried out in pure N{sub 2} and CO{sub 2} (pyrolysis experiments), and another is prepared in N{sub 2} + 5%O{sub 2} and CO{sub 2} + 5%O{sub 2}. Coal samples included raw coal, low density fraction coal and medium density fraction coal in all experiments. The present study is a further effort to extend our knowledge about physical and chemical structural characteristics and reactivity of char in the presence of high concentration CO{sub 2}. Combustion and pyrolysis of a density fractionated China coal at drop tube furnace yielded the following conclusions. Compared to oxy-chars obtained under pure CO{sub 2} atmosphere, the swelling ratios of char obtained in pure N{sub 2} atmosphere are higher. When adding 5%O{sub 2}, experimental results are completely different with those of the pyrolysis experiment. In comparison with the oxy-chars obtained under CO{sub 2} + 5%O{sub 2} atmosphere, the swelling ratios of the char obtained in N{sub 2} + 5%O{sub 2} atmosphere are lower. In the pyrolysis experiment, the BET surfaces Area of the oxy-chars are about 10-20 times as much as chars. When adding 5%O{sub 2}, the BET surfaces Area of the oxy-chars are about two to four times as much as chars. During pyrolysis experiment, the total pore volumes of the oxy-chars obtained under pure CO

Experimental comparison of biomass chars with other catalysts for tar reduction

NARCIS (Netherlands)

Abu El-Rub, Ziad; Bramer, Eduard A.; Brem, Gerrit

2008-01-01

In this paper the potential of using biomass char as a catalyst for tar reduction is discussed. Biomass char is compared with other known catalysts used for tar conversion. Model tar compounds, phenol and naphthalene, were used to test char and other catalysts. Tests were carried out in a fixed bed

Hot char-catalytic reforming of volatiles from MSW pyrolysis

International Nuclear Information System (INIS)

Wang, Na; Chen, Dezhen; Arena, Umberto; He, Pinjing

2017-01-01

Highlights: • Volatile from MSW pyrolysis is reformed with hot char from the same pyrolysis process. • The yields of syngas increase evidently with H 2 being the main contributor and the major component of the syngas. • Pyrolysis oil becomes light and its composition distribution is narrowed. • The HHV, volatile elements and alkali metals contents in the char decrease. • The emissions including SO 2 , NO, NO 2 and HCN changed after reforming process. - Abstract: Volatile products obtained from pyrolysis of municipal solid waste (MSW), including syngas and pyrolysis oil, were forced to contact the hot char from the same pyrolysis process at 500–600 °C in a fixed bed reactor to be reformed. The yields and properties of syngas, char and pyrolysis liquid were investigated; and the energy re-distribution among the products due to char reforming was quantified. The preliminary investigation at lab scale showed that hot char-catalytic reforming of the volatiles leads to an increase in the dry syngas yield from 0.25 to 0.37 N m 3 kg −1 MSW at 550 °C. Accordingly, the carbon conversion ratio into syngas increases from 29.6% to 35.0%; and the MSW chemical energy transferred into syngas increased from 41.8% to 47.4%. The yield of pyrolysis liquid products, including pyrolysis oil and water, decreased from 27.3 to 16.5 wt%, and the molecular weight of the oil becoming lighter. Approximately 60% of the water vapour contained in the volatiles converted into syngas. After reforming, the concentrations of SO 2 and HCN in the syngas decreases, while those of NO and NO 2 increase. The char concentrations of N, H, C and alkali metal species decreased and its higher heating value decreased too.

Kinetic Analysis of Char Thermal Deactivation

DEFF Research Database (Denmark)

Zolin, Alfredo; Jensen, Anker; Dam-Johansen, Kim

2001-01-01

and demineralized Dietz from USA, and two alternative fuels, Danish leached straw and petroleum coke, were used in the experiments. The coal chars from demineralized Dietz, Illinois no. 6, and Cerrejon deactivate readily, whereas petroleum coke and Blair Athol show a relative high resistance to deactivation....... Leached straw deactivates significantly, but maintains at any heat-treatment temperature a higher reactivity than the other chars. The inertinite-rich coal Blair Athol is more resistant to deactivation than two vitrinite-rich coals of the same ASTM rank, Cerrejon and Illinois no. 6. Cerrejon and Illinois...

Mixed Waste Treatment Using the ChemChar Thermolytic Detoxification Technique

International Nuclear Information System (INIS)

Kuchynka, D.J.

1997-01-01

This R and D program addresses the treatment of mixed waste employing the ChemChar Thermolytic Detoxification process. Surrogate mixed waste streams will be treated in a four inch diameter, continuous feed, adiabatic reactor with the goal of meeting all regulatory treatment levels for the contaminants in the surrogates with the concomitant production of contaminant free by-products. Successful completion of this program will show that organic contaminants in mixed waste surrogates will be converted to a clean, energy rich synthesis gas capable of being used, without further processing, for power or heat generation. The inorganic components in the surrogates will be found to be adsorbed on a macroporous coal char activated carbon substrate which is mixed with the waste prior to treatment. These contaminants include radioactive metal surrogate species, RCRA hazardous metals and any acid gases formed during the treatment process. The program has three main tasks that will be performed to meet the above objectives. The first task is the design and construction of the four inch reactor at Mirage Systems in Sunnyvale, CA. The second task is production and procurement of the activated carbon char employed in the ChemChartest runs and identification of two surrogate mixed wastes. The last task is testing and operation of the reactor on char/surrogate waste mixtures to be performed at the University of Missouri. The deliverables for the project are a Design Review Report, Operational Test Plan, Topical Report and Final Report. This report contains only the results of the design and construction carbon production-surrogate waste identification tasks.Treatment of the surrogate mixed wastes has just begun and will not be reported in this version of the Final Report. The latter will be reported in the final version of the Final Report

The thermal history of char as disclosed by carbon isotope ratios

DEFF Research Database (Denmark)

Egsgaard, Helge; Ambus, Per; Ahrenfeldt, Jesper

In laboratory experiments, biomass char was produced under controlled conditions using wood chips from French pinewood. Different char qualities were obtained by pyrolysing the biomass at similar heating rates with end-temperatures ranging from 250 to 1000 o C. The char was analysed by flash...... pyrolysis and isotope ratio mass spectrometry. The results demonstrate that the temperature history of the char is reflected in the fine variation of carbon isotopes. The compound classes responsible for the variation were identified. Key words: Isotope ratio, flash pyrolysis, hot gas cleaning...

Coal-char combustion in a fluidised bed reactor

Energy Technology Data Exchange (ETDEWEB)

Mehrotra, S.P.; Pande, M. [Indian Institute of Technolgy, Kanpur (India)

2001-12-01

Combustion of bituminous coal chars ranging from 0.8 mm to 1.8 mm has been studied in a fluidised bed reactor at temperatures ranging from 500 to 850{sup o}C. The fluidised bed consists of inert sand particles of average size of 0.5 mm and reactive coal char particles. A heat balance has been worked out to calculate the rate of combustion of char from measured incremental changes in the bed temperature during combustion. Investigations on partially burnt particles suggest that the ash layer which builds up around the burning core of char particles is non-flaking and the particles burn in a shrinking core manner. Analysis of rate data indicates that the rate of combustion is controlled by chemical reaction kinetics, though diffusion of oxygen through the bundary layer begins to influence the overall reaction kinetics at higher temperatures. The burnt out time varies linearly with particle size. Activation energy for the chemical reaction control regime is found to be around 68 kJ/mole.

Lead sorption characteristics of various chicken bone part-derived chars.

Science.gov (United States)

Park, Jong-Hwan; Wang, Jim J; Kim, Seong-Heon; Kang, Se-Won; Cho, Ju-Sik; Delaune, Ronald D; Ok, Yong Sik; Seo, Dong-Cheol

2018-01-18

Recycling food waste for beneficial use is becoming increasingly important in resource-limited economy. In this study, waste chicken bones of different parts from restaurant industry were pyrolyzed at 600 °C and evaluated for char physicochemical properties and Pb sorption characteristics. Lead adsorption isotherms by different chicken bone chars were carried out with initial Pb concentration range of 1-1000 mg L -1 at pH 5. The Pb adsorption data were better described by the Langmuir model (R 2  = 0.9289-0.9937; ARE = 22.7-29.3%) than the Freundlich model (R 2  = 0.8684-0.9544; ARE = 35.4-72.0%). Among the chars derived from different chicken bone parts, the tibia bone char exhibited the highest maximum Pb adsorption capacity of 263 mg g -1 followed by the pelvis (222 mg g -1 ), ribs (208 mg g -1 ), clavicle (179 mg g -1 ), vertebrae (159 mg g -1 ), and humerus (135 mg g -1 ). The Pb adsorption capacities were significantly and positively correlated with the surface area, phosphate release amount, and total phosphorus content of chicken bone chars (r ≥ 0.9711). On the other hand, approximately 75-88% of the adsorbed Pb on the chicken bone chars was desorbable with 0.1 M HCl, indicating their recyclability for reuse. Results demonstrated that chicken bone char could be used as an effective adsorbent for Pb removal in wastewater.

Thermal analysis of charring materials based on pyrolysis interface model

Directory of Open Access Journals (Sweden)

Huang Hai-Ming

2014-01-01

Full Text Available Charring thermal protection systems have been used to protect hypersonic vehicles from high heat loads. The pyrolysis of charring materials is a complicated physical and chemical phenomenon. Based on the pyrolysis interface model, a simulating approach for charring ablation has been designed in order to obtain one dimensional transient thermal behavior of homogeneous charring materials in reentry capsules. As the numerical results indicate, the pyrolysis rate and the surface temperature under a given heat flux rise abruptly in the beginning, then reach a plateau, but the temperature at the bottom rises very slowly to prevent the structural materials from being heated seriously. Pyrolysis mechanism can play an important role in thermal protection systems subjected to serious aerodynamic heat.

Pyrolysis of superfine pulverized coal. Part 4. Evolution of functionalities in chars

International Nuclear Information System (INIS)

Liu, Jiaxun; Ma, Yang; Luo, Lei; Ma, Junfang; Zhang, Hai; Jiang, Xiumin

2017-01-01

Highlights: • A combination of XPS and NMR is adopted for analyzing char chemical structures during superfine pulverized coal pyrolysis. • The chemisorbed NO can be transformed into pyridine N with the favor of adjacent oxygenated groups in chars. • Particle size has significant influence on oxygen-containing configurations in chars. - Abstract: The properties of the coal-derived char play crucial roles in coal conversion reactions and the formation of air pollutants. The nascent char is highly reactive due to the existence of numerous free radicals, active sites, and organic functional groups on its surface. Here, we showed that a combination of nuclear magnetic resonance spectroscopy (NMR) and X-ray photoelectron spectroscopy (XPS) techniques is an effective and precise way to characterize the occurrence, distribution, and evolution of organic functionalities in coal chars. Using these methods, we explored detailed information about chemical features of superfine pulverized coal chars in different atmospheres, and we also discussed the influence of particle size on the evolutionary behavior of functionalities. Results indicate that, in both N_2 and CO_2 atmospheres, the content of C−O species increases with the reduction in char particle sizes. This increment facilitates the heterogeneous reduction of NOx on char surfaces. The chemisorbed NO is susceptible to being incorporated into chars, and being transformed into pyridine-type nitrogen with the favor of adjacent oxygen-containing groups. Moreover, the significant increment in oxygen-containing groups with the reduction of particle size is further confirmed through "1"3C NMR analysis. It was shown that there is an excellent correlation between estimates derived from XPS and NMR for oxygen configuration. The findings from this work provide some new insights into NOx reduction mechanisms and shed light on the practical application of superfine pulverized coal in the future.

Study on pore structure properties of steam activated biomass chars

Energy Technology Data Exchange (ETDEWEB)

Shu, Tong; Lu, Fei; Wang, Qinchao; Lu, Ping [Nanjing Normal Univ. (China). School of Energy and Mechanical Engineering

2013-07-01

Wheat straw and rice husk chars were prepared in a fixed bed reactor at different pyrolysis temperatures (673, 873 and 1,073K) and different pyrolysis procedure. The steam activated chars were also prepared in a fixed bed reactor at the following conditions: activation temperature is 1,073K, the flow rate of N{sub 2} is 5L/min, and N{sub 2} and H{sub 2}O molar ratio is 1:1. The specific surface area, pore structure and micro-morphology of different kinds of prepared biomass chars were measured by NOVA1000e analysis instrument and JSM-5610LV scanning electron microscopy (SEM), respectively. Results indicated that the internal structure was improved significantly by steam activation through enlarging the specific surface area and enriching the porosity. The wheat straw char prepared by both rapid pyrolysis at 873K and activation by steam is better than others, whose DR surface area increases from 3.10 to 1099.99m{sup 2}/g. The N{sub 2} adsorption volume of steam activated biomass chars has been significant promoted.

Treatability study of absorbent polymer waste form for mixed waste treatment

International Nuclear Information System (INIS)

Herrmann, S. D.; Lehto, M. A.; Stewart, N. A.; Croft, A. D.; Kern, P. W.

2000-01-01

A treatability study was performed to develop and characterize an absorbent polymer waste form for application to low level (LLW) and mixed low level (MLLW) aqueous wastes at Argonne National Laboratory-West (ANL-W). In this study absorbent polymers proved effective at immobilizing aqueous liquid wastes in order to meet Land Disposal Restrictions for subsurface waste disposal. Treatment of aqueous waste with absorbent polymers provides an alternative to liquid waste solidification via high-shear mixing with clays and cements. Significant advantages of absorbent polymer use over clays and cements include ease of operations and waste volume minimization. Absorbent polymers do not require high-shear mixing as do clays and cements. Granulated absorbent polymer is poured into aqueous solutions and forms a gel which passes the paint filter test as a non-liquid. Pouring versus mixing of a solidification agent not only eliminates the need for a mixing station, but also lessens exposure to personnel and the potential for spread of contamination from treatment of radioactive wastes. Waste minimization is achieved as significantly less mass addition and volume increase is required of and results from absorbent polymer use than that of clays and cements. Operational ease and waste minimization translate into overall cost savings for LLW and MLLW treatment

Investigation on the ignition, thermal acceleration and characteristic temperatures of coal char combustion

International Nuclear Information System (INIS)

Zhang, Bin; Fu, Peifang; Liu, Yang; Yue, Fang; Chen, Jing; Zhou, Huaichun; Zheng, Chuguang

2017-01-01

Highlights: • A new thermal model and measuring method for the ignition temperature are proposed. • Ignition occurs in a region but not a point with ambient conditions changing. • Ignition region is measured from the minimum to maximum ignition temperature. • T_i_g_,_m_a_x of coal char in TG-DSC is in line with the ignition temperature of EFR. - Abstract: Through using a new thermal analysis model and a method of coal/char combustion, the minimum ignition temperature and minimum ignition heat of three different ranks of pulverized coal char were measured by simultaneous Thermogravimetry and Differential Scanning Calorimetry (TG-DSC) experiments. The results show that the ignition of coal char occurs in the range between the minimum ignition temperature and the inflection-point temperature. The thermal acceleration and its gradient G_T increase with increasing heating rate and decrease with increasing coal char rank. The higher the G_T of the coal char, the more easily the ignition occurs and more rapidly the burning and burnout occur. The data show that the G_T of coal char of SLH lignite is 1.6 times more than that of coal char of ZCY bituminous and JWY anthracite in ignition zone, and 3.4 times in burning zone. The characteristic temperatures increase with increasing temperature of prepared char, heating rate and char rank. Moreover, the T_i_g_,_m_a_x calculated in DSC experiment is approximately in line with the ignition temperature obtained in the entrained flow reactor, which demonstrates the feasibility of the proposed theory.

Time domain-nuclear magnetic resonance study of chars from southern hardwoods

International Nuclear Information System (INIS)

Elder, Thomas; Labbe, Nicole; Harper, David; Rials, Timothy

2006-01-01

Chars from the thermal degradation of silver maple (Acer saccharinum), red maple (Acer rubrum), sugar maple (Acer saccharum), and white oak (Quercus spp.), performed at temperatures from 250 to 350 o C, were examined using time domain-nuclear magnetic resonance spectroscopy. Prior to analysis, the chars were equilibrated under conditions insuring the presence of bound water only and both bound water and free water. Transverse relaxation times were found to be related to the moisture content of the chars, which varied with temperature. At elevated temperatures the number of signals assigned to free water decreased, indicative of an increase in pore size within the chars

NO formation during oxy-fuel combustion of coal and biomass chars

DEFF Research Database (Denmark)

Zhao, Ke; Jensen, Anker Degn; Glarborg, Peter

2014-01-01

The yields of NO from combustion of bituminous coal, lignite, and biomass chars were investigated in O2/N2 and O2/CO 2 atmospheres. The experiments were performed in a laboratory-scale fixed-bed reactor in the temperature range of 850-1150 °C. To minimize thermal deactivation during char preparat......The yields of NO from combustion of bituminous coal, lignite, and biomass chars were investigated in O2/N2 and O2/CO 2 atmospheres. The experiments were performed in a laboratory-scale fixed-bed reactor in the temperature range of 850-1150 °C. To minimize thermal deactivation during char...

Kinetics of coal combustion: Part 3, Mechanisms and kinetics of char combustion

Energy Technology Data Exchange (ETDEWEB)

Gavalas, G. R.; Flagan, R. C. [California Inst. of Tech., Pasadena, CA (USA)

1988-09-01

This report summarizes a three-year research program aimed at developing this level of understanding of char combustion through a combination of detailed analysis of chars as produced during devolatilization and as they evolve during oxidation, and theoretical studies of the porous microstructures and of pore diffusion and reaction within the coal particles. A small number of coals have been studied in detail, namely a HVA bituminous (PSOC 1451), a sub-bituminous (PSOC 1488), and a lignite (PSOC 1443). Chars have been generated from size-classified samples of these coals by pyrolysis in an inert atmosphere in a drop tube furnace. The chars were then characterized both chemically and physically. Subsequent oxidation studies were performed on these chars. 42 refs., 54 figs., 4 tabs.

Structural evolution of biomass char and its effect on the gasification rate

International Nuclear Information System (INIS)

Fatehi, Hesameddin; Bai, Xue-Song

2017-01-01

Highlights: • A comprehensive model was developed to describe the evolution of biomass char structure. • An effectiveness factor was used to account for the intra-particle chemical and physical processes. • The effect of the structural evolution of the multi-pore structure on biomass char reactivity was analyzed. • The multi-pore model yields results in satisfactory agreement with experiments. - Abstract: The evolution of char porous structure can affect the conversion rate of the char by affecting the intra-particle transport, especially in the zone II conversion regime. A multi-pore model based on the capillary pore theory is developed to take into account different conversion rates for pores with different radii. The model is valid for biomass chars produced under relatively low heating rates, when the original beehive structure of the biomass is not destroyed during the pyrolysis stage. The contribution of different pores with different radius is taken into account using an effectiveness factor presented for each pore radius with respect to different reactions. As the char conversion proceeds, the pore enlargement increases the contribution of micro-pores; consequently the effective surface area will increase. The increase in the effective surface area leads to an increased reactivity of char during the entire conversion process. This model is used to analyze the steam gasification process of biomass char of centimeter sizes. The results from the present multi-pore model are in better agreement with experimental data than those from a corresponding single pore model. Since the multi-pore model accommodates the detailed intra-particle transport, it is a useful basis toward developing a more predictive model for biomass char gasification.

Thermogravimetric determination of the carbon dioxide reactivity of char from some New Zealand coals and its association with the inorganic geochemistry of the parent coal

Energy Technology Data Exchange (ETDEWEB)

Beamish, B.B.; Shaw, K.J.; Rodgers, K.A.; Newman, J. [University of Auckland, Auckland (New Zealand). Dept. of Geology

1998-02-01

Thermogravimetrically-determined carbon dioxide reactivities of char formed from New Zealand coals, ranging in rank from lignite to high volatile bituminous, vary from 0.12 to 10.63 mg/h/mg on a dry, ash-free basis. The lowest rank subbituminous coal chars have similar reactivities to the lignite coal chars. Calcium content of the char shows the strongest correlation with reactivity, which increases as the calcium content increases. High calcium per se does not directly imply a high char reactivity. Organically-bound calcium catalyses the conversion of carbon to carbon monoxide in the presence of carbon dioxide, whereas calcium present as discrete minerals in the coal matrix e.g., calcite, fails to significantly affect reactivity. Catalytic effects of magnesium, iron, sodium and phosphorous are not as obvious, but can be recognised for individual chars. The thermogravimetric technique provides a fast, reliable analysis that is able to distinguish char reactivity differences between coals, which may be due to any of the above effects. 27 refs., 6 figs., 4 tabs.

Relation between coal rank, char reactivity, textural properties and NO emissions

Energy Technology Data Exchange (ETDEWEB)

Arenillas, A.; Rubiera, F.; Parra, J.B.; Pis, J.J. [Instituto Nacional del Carbon, Oviedo (Spain)

1999-07-01

A low volatile bituminous coal was pyrolysed at different heating rates to produce chars with different textural properties. There was a linear relationship between char reactivity and active surface area. The effect of coal rank on coal char textural properties was studied using a range of bituminous coals. The influence of textural properties and reactivity on NO emissions, and on the heterogeneous reduction of NO is discussed. 6 refs., 2 figs., 2 tabs.

DDGS chars gasification with CO{sub 2}: a kinetic study using TG analysis

Energy Technology Data Exchange (ETDEWEB)

Meng, Xiangmei; Jong, Wiebren de; Fu, Ningjie; Verkooijen, Adrian H.M. [Delft University of Technology, Process and Energy Department, Faculty of Mechanical, Maritime and Materials Engineering, Delft (Netherlands)

2011-12-15

Dry Distiller's Grains with Solubles (DDGS) is a by-product during ethanol production from cereals which is currently mainly used as feedstock for cattle. With the growth of the ethanol industry, the increasing supply of DDGS may saturate the livestock feed market; thus, its potential applications need to be explored. DDGS gasification in a 100-kW{sub th} circulating fluidized bed (CFB) steam-O{sub 2} blown gasifier has been studied. However, the modeling of DDGS gasification process encounters difficulties due to the unavailable knowledge of DDGS char gasification kinetics. Therefore, in this paper, gasification kinetics of DDGS char with CO{sub 2} was investigated using thermogravimetric analysis (TGA). Two different types of char samples have been tested. Char type one (PYR-Char) was obtained after DDGS pyrolysis in a TGA at a final temperature of 750 C or 850 C for 20 min. Char type two (CFB-Char) was obtained after DDGS gasification in the 100-kW{sub th} CFB gasifier within the temperature range of 790 C to 820 C with a steam/biomass mass ratio of 0.81 and oxygen to biomass stoichiometric ratio of approximately 0.38. The influences of pyrolysis temperature (750 C, 850 C), heating rate (10 C/min, 30 C/min, 50 C/min, 70 C/min), CO{sub 2} concentration (10, 20, 30 vol.%), and gasification temperature (900 C, 1,000 C, 1,100 C) on the reaction rate of char-CO{sub 2} reaction were determined. Two representative gas-solid reaction models, the volumetric reaction model (VRM) and the shrinking core model (SCM) were applied in order to determine kinetic parameters. It was found that the calculated activation energy (E{sub a}) values using SCM were slightly lower than those using VRM. The calculated E{sub a} values for PYR-Char using both models were in the range of 100-165 kJ/mol, while the calculated E{sub a} values for CFB-Char were in the range of 55-100 kJ/mol. It was observed by scanning electron microscopy (SEM) that CFB-Char was more fragile and PYR-Char

Particle-based characterisation of pulverised coals and chars for carbon burnout studies

Energy Technology Data Exchange (ETDEWEB)

Gibbins, J.R.; Seitz, M.H.; Kennedy, S.M.; Beeley, T.J.; Riley, G.S. [Imperial College of Science, Technology and Medicine, London (United Kingdom). Mechanical Engineering Department

1999-07-01

The study of individual particle properties, as opposed to averaged behaviour of differing particles, was carried out for the combustion of coals and chars using optical microscopy and digital image processing. Chars from entrained flow reactors and corresponding pulverized fuel samples were characterized to examine possible char particle origins for real heterogeneous particles. 7 refs., 5 figs., 1 tab.

Characterization of bio char derived from tapioca skin

Science.gov (United States)

Hasnan, F. I.; Iamail, K. N.; Musa, M.; Jaapar, J.; Alwi, H.; Hamid, K. K. K.

2018-03-01

Pyrolysis of tapioca skin was conducted to produce bio chars in the range between 500°C–800°C. Surface modification treatment were performed on bio chars by using chemicals within 24 hours at 30°C and hot water within 1 hour to enhance the bio char’s adsorption properties according to surface area, pore volume, pore size, crystallinity structure and functional groups. The samples were characterized by using BET, XRD, FTIR and Methylene Blue adsorption. Based on BET result, it showed the surface area increased as the pyrolysis temperature increased followed by pore volume and pore size for S0. The optimum temperature for SNaOH, SHW and SMeOH was at 600°C, 700°C and 800°C with the surface area of 75.9874, 274.5066 and 351.5531 m2/g respectively compared to S0 while SP3HO4 has the worst result since it felt on macroporous structure. The percentage of MB adsorption was followed the size of bio chars surface area. Based on FTIR result, at temperature 500°C to 700°C, the bio chars still have functional groups while at 800°C, many functional groups were diminished due to high temperature struck on them. XRD result showed all the bio chars were amorphous. In conclusion, the best surface modification treatment was by Methanol followed by hot water and Sodium Hydroxide at temperature of 700°C and 800°C while Ortho-Phosphoric acid was the worst one and was not suitable for bio char’s surface modification for adsorption purpose.

Oxidation rates of carbon and nitrogen in char residues from solid fuels

Energy Technology Data Exchange (ETDEWEB)

Karlstroem, O.

2013-06-01

Computational fluid dynamics (CFD) modeling is an important tool in designing new combustion systems. By using CFD modeling, entire combustion systems can be modeled and the emissions and the performance can be predicted. CFD modeling can also be used to develop new and better combustion systems from an economical and environmental point of view. In CFD modeling of solid fuel combustion, the combustible fuel is generally treated as single fuel particles. One of the limitations with the CFD modeling concerns the sub-models describing the combustion of single fuel particles. Available models in the scientific literature are in many cases not suitable as submodels for CFD modeling since they depend on a large number of input parameters and are computationally heavy. In this thesis CFD-applicable models are developed for the combustion of single fuel particles. The single particle models can be used to improve the combustion performance in various combustion devices or develop completely new technologies. The investigated fields are oxidation of carbon (C) and nitrogen (N) in char residues from solid fuels. Modeled char-C oxidation rates are compared to experimental oxidation rates for a large number of pulverized solid fuel chars under relevant combustion conditions. The experiments have been performed in an isothermal plug flow reactor operating at 1123-1673 K and 3-15 vol.% O{sub 2}. In the single particle model, the char oxidation is based on apparent kinetics and depends on three fuel specific parameters: apparent pre-exponential factor, apparent activation energy, and apparent reaction order. The single particle model can be incorporated as a sub-model into a CFD code. The results show that the modeled char oxidation rates are in good agreement with experimental char oxidation rates up to around 70% of burnout. Moreover, the results show that the activation energy and the reaction order can be assumed to be constant for a large number of bituminous coal chars

Sorption of diuron, atrazine, and copper ion on chars with long-term natural oxidation in soils

Science.gov (United States)

Cheng, C.; Lin, T.; Lai, C.

2011-12-01

Biochar has been proposed as a measure to sequestrate carbon (C) and to increase soil fertility in sustainable agriculture. However, its sorption characteristics to herbicides, such as lowing herbicides efficacy, may constrain its agricultural application. This assertion may be arguable because most studies so far were conducted with the newly produced char and barely considered the "ageing effect" of old char since it could be oxidized over long time. In this study, historical char samples were collected and compared with the newly produced char. Batch sorption studies of diuron, atrazine, and copper ion onto chars was performed. Greater sorption of Cu was observed on the historical char samples and reached a saturated sorption at 30 mg g-1 for Cu, much higher adsorption value than newly produced char at 4 mg g-1. In contrast, sorption of diuron and atrazine on newly produced char had the highest sorption capacity than the historical char samples. The historical chars also had much higher negative charge than the newly produced char, but its surface area were lower than the new char. The results indicated that change in surface functional groups through natural oxidation rather than the change of surface area may have more pronounced influences on sorption characteristics, in which the negative charge on the historical chars' surface could hinder the adsorption of diuron and atrazine while enhance the sorption to copper ion. Biological assay to test the toxicity of diuron and copper ion for both historical and new chars on rye seed were conducted and will be presented in our poster.

CHARCOAL PACKED FURNACE FOR LOW-TECH CHARRING OF BONE

DEFF Research Database (Denmark)

Jacobsen, P.; Dahi, Elian

1997-01-01

A low-tech furnace for charring of raw bone using char coal is developed and tested. The furnace consists of a standard oil drum, fitted with simple materials as available in every market in small towns in developing counties. 80 kg of raw bone and 6 kg of charcoal are used for production of 50 kg...

Effects of Biomass Feedstocks and Gasification Conditions on the Physiochemical Properties of Char

Directory of Open Access Journals (Sweden)

Raymond L. Huhnke

2013-08-01

Full Text Available Char is a low-value byproduct of biomass gasification and pyrolysis with many potential applications, such as soil amendment and the synthesis of activated carbon and carbon-based catalysts. Considering these high-value applications, char could provide economic benefits to a biorefinery utilizing gasification or pyrolysis technologies. However, the properties of char depend heavily on biomass feedstock, gasifier design and operating conditions. This paper reports the effects of biomass type (switchgrass, sorghum straw and red cedar and equivalence ratio (0.20, 0.25 and 0.28, i.e., the ratio of air supply relative to the air that is required for stoichiometric combustion of biomass, on the physiochemical properties of char derived from gasification. Results show that the Brunauer-Emmett-Teller (BET surface areas of most of the char were 1–10 m2/g and increased as the equivalence ratio increased. Char moisture and fixed carbon contents decreased while ash content increased as equivalence ratio increased. The corresponding Fourier Transform Infrared spectra showed that the surface functional groups of char differed between biomass types but remained similar with change in equivalence ratio.

CHAR CRYSTALLINE TRANSFORMATIONS DURING COAL COMBUSTION AND THEIR IMPLICATIONS FOR CARBON BURNOUT

Energy Technology Data Exchange (ETDEWEB)

ROBERT H. HURT

1998-09-08

temperatures approaching 3000 o C. For the measurement of temperature histories an optical diagnostic is being developed that offers sufficient spatial resolution to distinguish the sample temperature from the substrate temperature. The optical diagnostic is based on a CID camera, a high-power lens, and movable mirrors to projecting multiple, filtered images onto a single chip. Oxidation kinetics are measured on the heat treated samples by a nonisothermal TGA technique. Task 2 Thermal deactivation kinetics. The goal of this task is to quantify thermal char deactivation as a function of temperature history and parent coal, with an emphasis on inert environments at temperatures and times found in combustion systems. The results are to be cast in the form of deactivation kinetics useful for incorporation in combustion models. Task 3 Crystal structure characterization. Crystal structure characterization provides important insight into the mechanisms of thermal char deactivation, and the degree of crystalline transformations has shown a strong correlation with reactivity changes in recent combustion studies [Davis et al., 1992, Beeley et al., 1996]. This task seeks to improve our understanding of char carbon crystalline transformations under combustion conditions by analyzing a large set of HRTEM fringe images for a series of flame-generated chars whose reactivities have been previously reported [Hurt et al., 1995, Beeley et al., 1996]. As a first step, a new technique is being developed for the quantitative analysis of fringe images, extending previous work to allow measurement of a complete set of crystal structure parameters including mean layer size, mean stacking height, interlayer spacing, layer curvature, amorphous fraction, and degree of anisotropy. The resulting database will revealing, at a very fundamental level, the basic differences in char crystal structure due to parent coal rank and to temperature history in the range of interest to combustion systems.

The carbon dioxide gasification characteristics of biomass char samples and their effect on coal gasification reactivity during co-gasification.

Science.gov (United States)

Mafu, Lihle D; Neomagus, Hein W J P; Everson, Raymond C; Okolo, Gregory N; Strydom, Christien A; Bunt, John R

2018-06-01

The carbon dioxide gasification characteristics of three biomass char samples and bituminous coal char were investigated in a thermogravimetric analyser in the temperature range of 850-950 °C. Char SB exhibited higher reactivities (R i , R s , R f ) than chars SW and HW. Coal char gasification reactivities were observed to be lower than those of the three biomass chars. Correlations between the char reactivities and char characteristics were highlighted. The addition of 10% biomass had no significant impact on the coal char gasification reactivity. However, 20 and 30% biomass additions resulted in increased coal char gasification rate. During co-gasification, chars HW and SW caused increased coal char gasification reactivity at lower conversions, while char SB resulted in increased gasification rates throughout the entire conversion range. Experimental data from biomass char gasification and biomass-coal char co-gasification were well described by the MRPM, while coal char gasification was better described by the RPM. Copyright © 2018 Elsevier Ltd. All rights reserved.

EFFECT OF CALCIUM ADDITION ON THE DEFLUORIDATION CAPACITY OF BONE CHAR

DEFF Research Database (Denmark)

Jacobsen, P.; Dahi, Elian

1997-01-01

Dosage of small amounts of calcium chloride to fluoride water prior to contact with bone char which has already been saturated with fluoride is shown to provide an additional fluoride removal capacity. The additionally obtained removal capacity increases with slower filtration velocities...... to be capable of reducing the fluoride concentration form 10 to about 0.5 mgF/L. The additionally saturated column is shown to be regenerated by simple adjustment of the pH of the water to 11 and allowing to flow for a few bed volumes. The useful regeneration capacity, where the fluoride concentration...... and increasing calcium dosage. A filtration velocity of 0.07 m/h, corresponding to a contact time of about 2 hours, and a dosage of 100 mgCa/L, are shown to provide an additional removal capacity of about 3 mgF/g, i.e. almost a doubling of the genuine removal capacity of the bone char. The process is shown...

Synthesis and Application of a Novel Polyamide Charring Agent for Halogen-Free Flame Retardant Polypropylene

Directory of Open Access Journals (Sweden)

Jie Liu

2013-01-01

Full Text Available A novel charring agent, poly(p-ethylene terephthalamide (PETA, for halogen-free flame retardant polypropylene was synthesized by using p-phthaloyl chloride (TPC and ethylenediamine through solution polycondensation at low temperature, and the effects of PETA on flame retardance of polypropylene (PP/IFR systems were studied. The experimental results showed that PETA could considerably enhance the fire retardant performance as proved by evidence of the increase of limiting oxygen index (LOI values, the results of UL-94 tests, and cone calorimeter tests (CCT. Fourier transform infrared spectroscopy (FTIR and scanning electron microscope (SEM demonstrated that an appropriate amount of PETA could react with PP/IFR system to form cross-link network; a more compact char layer could be formed which was responsible for the improved thermal and flame retardant properties of PP/IFR systems. However, the superfluous amount of PETA would play the negative role.

Applications of Polymers as Pharmaceutical Excipients in Solid Oral Dosage Forms.

Science.gov (United States)

Debotton, Nir; Dahan, Arik

2017-01-01

Over the last few decades, polymers have been extensively used as pharmaceutical excipients in drug delivery systems. Pharmaceutical polymers evolved from being simply used as gelatin shells comprising capsule to offering great formulation advantages including enabling controlled/slow release and specific targeting of drugs to the site(s) of action (the "magic bullets" concept), hence hold a significant clinical promise. Oral administration of solid dosage forms (e.g., tablets and capsules) is the most common and convenient route of drug administration. When formulating challenging molecules into solid oral dosage forms, polymeric pharmaceutical excipients permit masking undesired physicochemical properties of drugs and consequently, altering their pharmacokinetic profiles to improve the therapeutic effect. As a result, the number of synthetic and natural polymers available commercially as pharmaceutical excipients has increased dramatically, offering potential solutions to various difficulties. For instance, the different polymers may allow increased solubility, swellability, viscosity, biodegradability, advanced coatings, pH dependency, mucodhesion, and inhibition of crystallization. The aim of this article is to provide a wide angle prospect of the different uses of pharmaceutical polymers in solid oral dosage forms. The various types of polymeric excipients are presented, and their distinctive role in oral drug delivery is emphasized. The comprehensive know-how provided in this article may allow scientists to use these polymeric excipients rationally, to fully exploit their different features and potential influence on drug delivery, with the overall aim of making better drug products. © 2016 Wiley Periodicals, Inc.

Report on results of research. Basic studies on characteristics of coal char gasification under pressure; Sekitan char no kaatsuka ni okeru gas ka tokuseino kiso kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This paper explains basic studies on characteristics of coal char gasification under pressure. Hydro-gasification of coal needs as a gasifying agent a large amount of hydrogen, which is effectively produced by the water gasification of exhaust unreacted residual char. In fiscal 1975, gasification was tested on Taiheiyo coal carbonized char by an atmospheric fluidized gasifier of 28 mm bore. In fiscal 1976, experiment was conducted under pressure by fully improving the auxiliary safety equipment. The char and gas yield increased with higher pressure in pressurized carbonization by an autoclave. In fiscal 1977, clinker was successfully prevented by using quartz sand for a fluidized medium. In fiscal 1978, two-stage continuous gasification was examined. In fiscal 1979, correlation was determined between operation factors such as gasification pressure, temperature, etc., and clinker formation/char reactivity. An experiment was conducted for particle pop-out using a pressurized fluidized bed of 100 mm inner diameter, with the pop-out quantity found to be proportional to the 0.38th power of a pressure. A high pressure fluidized gasifier was built having a char processing capacity of 1 t/day, 20 atmospheric pressure, and an inner diameter of 100 mm. In fiscal 1980, this device was continuously operated, elucidating problems for the practicability. (NEDO)

Gas cleaning with hot char beds studied by stable isotopes

DEFF Research Database (Denmark)

Egsgaard, Helge; Ahrenfeldt, Jesper; Ambus, Per

2014-01-01

The chemistry taking place in a high temperature char bed used for binding aromatic tar compounds has been studied in detail. 13C labelled tar compounds were used to trace the incorporation into the char bed using isotope ratio mass spectrometry (IRMS) and GC-MS. Furthermore, compounds labelled...

Modifying Char Dustcake Pressure Drop Using Particulate Additives

Energy Technology Data Exchange (ETDEWEB)

Landham, C.; Dahlin, R.S.; Martin, R.A.; Guan, X.

2002-09-19

Coal gasification produces residual particles of coal char, coal ash, and sorbent that are suspended in the fuel gas stream exiting the gasifier. In most cases, these particles (referred to, hereafter, simply as char) must be removed from the stream prior to sending the gas to a turbine, fuel cell, or other downstream device. Currently, the most common approach to cleaning the gas stream at high temperature and pressure is by filtering the particulate with a porous ceramic or metal filter. However, because these dusts frequently have small size distributions, irregular morphology, and high specific surface areas, they can have very high gas flow resistance resulting in hot-gas filter system operating problems. Typical of gasification chars, the hot-gas filter dustcakes produced at the Power Systems Development Facility (PSDF) during recent coal gasification tests have had very high flow resistance (Martin et al, 2002). The filter system has been able to successfully operate, but pressure drops have been high and filter cleaning must occur very frequently. In anticipation of this problem, a study was conducted to investigate ways of reducing dustcake pressure drop. This paper will discuss the efficacy of adding low-flow-resistance particulate matter to the high-flow-resistance char dustcake to reduce dustcake pressure drop. The study had two parts: a laboratory screening study and confirming field measurements at the PSDF.

Flame retardancy and thermal behavior of intumescent flame-retardant EVA composites with an efficient triazine-based charring agent

Science.gov (United States)

Xu, Bo; Ma, Wen; Wu, Xiao; Qian, Lijun; Jiang, Shan

2018-04-01

Intumescent flame retardant (IFR) EVA composites were prepared based on a hyperbranched triazine charring-foaming agent (HTCFA) and ammonium polyphosphate (APP). The synergistic effect of HTCFA and APP on the flame retardancy and thermal behavior of the composites were investigated through flammability tests, cone calorimeter measurements, thermogravimetric analysis (TGA) including evolved gas analysis (TG-IR) and residue analysis (Fourier transform infrared (FTIR), laser Raman spectroscopy (LRS), x-ray Photoelectron Spectroscopy (XPS) and scanning electron microscopy (SEM)). The flammability test results showed HTCFA/APP (1/3) system presented the best synergistic effect in flame-retardant EVA composites with the highest LOI value and UL-94 V-0 rating. As for cone calorimeter results, IFR changed the combustion behavior of EVA and resulted in remarkable decrease of flammability and smoke product. TGA results showed the synergistic effect between APP and HTCFA could strengthen the char-forming ability of composites. TG-IR results indicated the melt viscosities and gas release with increasing temperature were well-correlated for EVA/IFR composite. The residue analysis results from SEM, LRS, FT-IR and XPS revealed IFR promoted forming more compact graphitic char layer, connected by rich P–O–C and P–N structures.

NO Reduction over Biomass and Coal Char during Simultaneous Combustion

DEFF Research Database (Denmark)

Zhao, Ke; Glarborg, Peter; Jensen, Anker Degn

2013-01-01

This paper reports an experimental study of NO reduction over chars of straw, bark, bituminous coal, and lignite. The experiments were performed in a fixed bed reactor in the temperature range 850–1150 °C. The chars were generated by in situ pyrolysis at the reaction temperature to minimize further...

Effect of pyrolysis pressure and heating rate on radiata pine char structure and apparent gasification reactivity

Energy Technology Data Exchange (ETDEWEB)

E. Cetin; R. Gupta; B. Moghtaderi [University of Newcastle, Callaghan, NSW (Australia). Discipline of Chemical Engineering, Faculty of Engineering and Built Environment, School of Engineering

2005-07-01

The knowledge of biomass char gasification kinetics has considerable importance in the design of advanced biomass gasifiers, some of which operate at high pressure. The char gasification kinetics themselves are influenced by char structure. In this study, the effects of pyrolysis pressure and heating rate on the char structure were investigated using scanning electron microscopy (SEM) analysis, digital cinematography, and surface area analysis. Char samples were prepared at pressures between 1 and 20 bar, temperatures ranging from 800 to 1000{degree}C, and heating rates between 20 and 500{degree}C/s. Our results indicate that pyrolysis conditions have a notable impact on the biomass char morphology. Pyrolysis pressure, in particular, was found to influence the size and the shape of char particles while high heating rates led to plastic deformation of particles (i.e. melting) resulting in smooth surfaces and large cavities. The global gasification reactivities of char samples were also determined using thermogravimetric analysis (TGA) technique. Char reactivities were found to increase with increasing pyrolysis heating rates and decreasing pyrolysis pressure. 22 refs., 8 figs., 2 tabs.

Conversion of char nitrogen to N2 under incomplete combustion conditions; Fukanzen nensho jokenka ni okeru char chuchisso no N2 eno tenka

Energy Technology Data Exchange (ETDEWEB)

Zhuang, Q.; Yamauchi, A.; Oshima, Y.; Wu, Z.; Otsuka, Y. [Tohoku University, Sendai (Japan). Institute for Chemical Reaction Science

1996-10-28

The effect of combustion conditions on conversion of char nitrogen to N2 was studied in the combustion experiment of char obtained by pyrolysis of coal. Char specimen was prepared by holding ZN coal of Chinese lignite in Ar atmosphere at 1123K for one hour. A batch scale quartz-made fluidized bed reactor was used for combustion experiment. After the specimen was fluidized in reaction gas, it was rapidly heated to start combustion reaction. CO, CO2 and N2 in produced gases were online measured by gas chromatography (GC). As the experimental result, under the incomplete combustion condition where a large amount of CO was produced by consuming almost all of O2, no NOx and N2O produced from char were found, and almost all of N-containing gas was N2. At the final stage of combustion, pyridinic-N disappeared completely, and pyrrolic-N decreased, while O-containing nitrogen complexes became a main component. It was thus suggested that O-containing nitrogen complexes are playing the role of intermediate product in combustion reaction. 7 refs., 4 figs., 1 tab.

Strategy for Passivating Char Efficiently at the Pilot Scale

Energy Technology Data Exchange (ETDEWEB)

Dunning, Timothy C [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2018-01-18

Fast pyrolysis is a promising pathway for the commercialization of liquid transportation fuels from biomass. Fast pyrolysis is performed at moderate heat (450-600 degrees Celcius) in an oxygen-deficient environment. One of the products of fast pyrolysis is biochar, which is often used as a heat source or as a soil amendment. Biochar is a partially reacted solid that is created in the production of bio-oil during fast pyrolysis. Biochar produced at these conditions contains significant quantities of carbon that adsorb oxygen when exposed to air. Biochar adsorption of oxygen is an exothermic process that may generate sufficient heat for combustion in ambient air. Biochar is also a self-insulating material which compounds the effects of heat generated internally. These factors lead to safety concerns and material handling difficulties. The Thermochemical Process Development Unit at the National Renewable Energy Laboratory operates a pilot plant that may be configured for fast pyrolysis, gasification, and will be introducing catalytic fast pyrolysis capabilities in 2018. The TCPDU designed and installed a system to introduce oxygen to collected biochar systematically for a controlled passivation. Biochar is collected and cooled in an oxygen deficient environment during fast pyrolysis. Oxygen is then introduced to the biochar on a mass flow basis. A sparger imbedded within the biochar sample near the bottom of the bed flows air diluted with nitrogen into the char bed, and excess gasses are removed from the top of the collection drum, above the char bed. Pressure within the collection drum is measured indicating adequate flow through filters. Sample weight is recorded before and after passivation. During passivation, temperature is measured at 18 points within the char bed. Oxygen content and temperature are measured leaving the char bed. Maximum temperature parameters were established to ensure operator safety during biochar passivation. Extensive passivation data was

Oxy-fuel combustion of millimeter-sized coal char: Particle temperatures and NO formation

DEFF Research Database (Denmark)

Brix, Jacob; Navascués, Leyre Gómez; Nielsen, Joachim Bachmann

2013-01-01

In this work, differences in particle temperature and NO yield during char oxidation in O2/N2 and O2/CO2 atmospheres, respectively, have been examined. A laboratory scale fixed bed reactor, operated isothermally at 1073 K, was used for combustion of millimeter-sized lignite and bituminous coal char...... increased with mass loading, by as much as 700 K above the furnace set point. The formation of NO from lignite char was not influenced by the change from N2 to CO2 whereas the NO yield from bituminous coal char was considerably lower in O2/CO2 compared O2/N2. For both chars the conversion to NO decreased...... as the O2 concentration or the particle size increased. However, for the bituminous coal char, a peak in NO yield was observed at an intermediate particle size of 0.1–0.2 g. The differences in the effect of gas atmosphere, O2 concentration, and particle mass on the NO yield from oxidation of bituminous...

Effect of filling surface-treated pyrolytic char on resistivity of rubber films

Directory of Open Access Journals (Sweden)

Pattraporn Yamkaya

2015-03-01

Full Text Available In this research, natural rubber (NR films filled with pyrolytic tire char, carbon black N234 and N330 were compared for their electrical resistivity. The filler loading was varied to be 5, 10, 15, 20 and 25% of dry rubber content. The effect of surfactant which is 2 %w/v sodium dodecyl sulfate (SDS was also investigated. In the experiments, it was necessary to disperse the pyrolytic char in ethyl alcohol while disperse carbon black (CB in ammonium hydroxide solution prior to mixing with the rubber latex and the filled NR film was prepared by casting the mixture on a plate. It was found that increasing the amount of pyrolytic char in the NR film could lower its resistivity. The surfactant, SDS, could help better dispersion of both CB and pyrolytic char, thereby decreasing the resistivity. In a separate experiment where hexane vapor was absorbed in NR film without surfactant, in the first 30 seconds, the rate of increasing resistivity of the CB-filled film was not seen as clearly as that of pyrolytic-char-filled film. For the films with surfactant, the slow increase in resistivity of the NR films filled with N330 and pyrolytic char during adsorbing hexane vapor was observed.

Heat Transfer in a Fixed Bed of Straw Char

DEFF Research Database (Denmark)

Fjellerup, Jan Søren; Henriksen, Ulrik Birk; Jensen, Anker

2003-01-01

A model for the thermal conductivity of a straw char bed has been developed. The model extends the work of Yagi and Kunii to describe heat transfer in a bed of cylinders, using a relationship between the interparticle distance and the external porosity. To verify the model, thermal conductivity...... the experimental uncertainty over the range of conditions investigated. The heat transfer model was used in a parametric study to evaluate the effect of gas flow rate, particle diameter, porosity, and temperature on the thermal conductivity in a straw char bed....... experiments were performed on shredded and un-shredded straw char samples, varying particle size, bed packing (loose or dense), and temperature. Predictions with the model, using the measured external porosity and particle diameter as input parameters, are in agreement with measurements within...

Preparation of porous bio-char and activated carbon from rice husk by leaching ash and chemical activation.

Science.gov (United States)

Ahiduzzaman, Md; Sadrul Islam, A K M

2016-01-01

Preparation porous bio-char and activated carbon from rice husk char study has been conducted in this study. Rice husk char contains high amount silica that retards the porousness of bio-char. Porousness of rice husk char could be enhanced by removing the silica from char and applying heat at high temperature. Furthermore, the char is activated by using chemical activation under high temperature. In this study no inert media is used. The study is conducted at low oxygen environment by applying biomass for consuming oxygen inside reactor and double crucible method (one crucible inside another) is applied to prevent intrusion of oxygen into the char. The study results shows that porous carbon is prepared successfully without using any inert media. The adsorption capacity of material increased due to removal of silica and due to the activation with zinc chloride compared to using raw rice husk char. The surface area of porous carbon and activated carbon are found to be 28, 331 and 645 m(2) g(-1) for raw rice husk char, silica removed rice husk char and zinc chloride activated rice husk char, respectively. It is concluded from this study that porous bio-char and activated carbon could be prepared in normal environmental conditions instead of inert media. This study shows a method and possibility of activated carbon from agro-waste, and it could be scaled up for commercial production.

Local dynamics and deformation of glass-forming polymers : modelling and atomistic simulations

NARCIS (Netherlands)

Vorselaars, B.

2008-01-01

The research described in the present thesis is about glassy phenomena and mechanical properties in vitrifiable polymer materials. Glasses are solid materials, but, in contrast to crystals, the structure is disordered. Polymers are macromolecular chains formed by covalently linking a very large

Electron paramagnetic resonance and dynamic nuclear polarization of char suspensions: surface science and oximetry

International Nuclear Information System (INIS)

Clarkson, R.B.; Odintsov, B.M.; Ceroke, P.J.; Ardenkjaer-Larsen, J.H.; Fruianu, M.; Belford, R.L.

1998-01-01

Carbon chars have been synthesized in our laboratory from a variety of starting materials, by means of a highly controlled pyrolysis technique. These chars exhibit electron paramagnetic resonance (EPR) line shapes which change with the local oxygen concentration in a reproducible and stable fashion; they can be calibrated and used for oximetry. Biological stability and low toxicity make chars good sensors for in vivo measurements. Scalar and dipolar interactions of water protons at the surfaces of chars may be utilized to produce dynamic nuclear polarization (DNP) of the 1 H nuclear spin population in conjunction with electron Zeeman pumping. Low-frequency EPR, DNP and DNP-enhanced MRI all show promise as oximetry methods when used with carbon chars. (author)

Bio-char derived from sewage sludge by liquefaction: Characterization and application for dye adsorption

Energy Technology Data Exchange (ETDEWEB)

Leng, Lijian [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environment Biology and Pollution Control, Hunan University, Ministry of Education, Changsha 410082 (China); Yuan, Xingzhong, E-mail: yxz@hnu.edu.cn [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environment Biology and Pollution Control, Hunan University, Ministry of Education, Changsha 410082 (China); Huang, Huajun [School of Land Resources and Environment, Jiangxi Agricultural University, Nanchang 330045 (China); Shao, Jianguang; Wang, Hou [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environment Biology and Pollution Control, Hunan University, Ministry of Education, Changsha 410082 (China); Chen, Xiaohong [School of Business, Central South University, Changsha 410083 (China); Zeng, Guangming [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environment Biology and Pollution Control, Hunan University, Ministry of Education, Changsha 410082 (China)

2015-08-15

Graphical abstract: - Highlights: • SS liquefaction bio-chars were effective on MG and MB removal from aqueous. • MG adsorption capacity depended strongly on carboxylic and phenolic groups. • Metal release accounted for nearly 30% of the total MG adsorbed on bio-chars. • Acetone and low temperature favor effective adsorbent production by liquefaction. - Abstract: Bio-chars produced by liquefaction of sewage sludge with methanol, ethanol, or acetone as the solvent at 260–380 °C were characterized in terms of their elemental composition, thermogravimetric characteristics, surface area and pore size distribution, and oxygen-containing functional groups composition. The surface area and total volume of the bio-chars were low, but the contents of oxygen-containing functional groups were high. The bio-chars were effective on Malachite green (MG) and Methylene blue (MB) removal from aqueous solution. The MG adsorption equilibrium data showed excellent fit to the Langmuir model and the kinetic data fitted well to the Pseudo-second-order model. Thermodynamic investigations indicated that MG adsorption on bio-char was spontaneous and endothermic. The MG adsorption mechanism appears to be associated with cation release and functional group participation. Additionally, liquefaction of SS with acetone as the solvent at low temperature (280 °C) would favor the production of bio-char adsorbent in terms of bio-char yield and MG and MB adsorption capacity.

Production and characterization of Lemna minor bio-char and its catalytic application for biogas reforming

International Nuclear Information System (INIS)

Muradov, Nazim; Fidalgo, Beatriz; Gujar, Amit C.; Garceau, Nathaniel; T-Raissi, Ali

2012-01-01

Pyrolysis of fast-growing aquatic biomass - Lemna minor (commonly known as duckweed) with the emphasis on production, characterization and catalytic application of bio-char is reported in this paper. The yield of bio-char was determined as a function of L. minor pyrolysis temperature and sweep gas flow rate. It was found that the pore development during L. minor pyrolysis was not significant and the changes in the reaction conditions (temperature and sweep gas flow rate) did not alter markedly the textural characteristics and BET surface area of the bio-char produced. Thermogravimetric/differential thermogravimetric (TG/DTG) analyses of L. minor and different bio-char samples in inert (helium) and oxidative (air) media showed substantial differences in their TG/DTG patterns. A comparison of scanning electron micrographs (SEM) of L. minor, bio-char and ash indicated that the basic structural features of L. minor remained intact and were not affected by thermolysis. The inorganic ash content of L. minor derived bio-char is significantly higher than that of typical terrestrial (plant) biomass. The energy dispersive spectroscopic (EDS) analysis of L. minor ash showed that it mostly consisted of silica, and small quantities of Na, K and Ca compounds. The treatment of bio-char with CO 2 at 800 °C increased its BET surface area. It was found that CO 2 -treated bio-char exhibited appreciable initial catalytic activity in biogas reforming. -- Highlights: ► New data on characterization of bio-chars derived from Lemna minor are presented. ► Effect of pyrolysis operational parameters on bio-char properties is determined. ► Basic skeletal structure of Lemna minor leaflets does not change during pyrolysis. ► Bio-chars show an appreciable initial catalytic activity for biogas reforming.

Coke, char and organic waste behaviour in the blast furnace with high injection rate

Directory of Open Access Journals (Sweden)

Gudenau, H. W.

2003-10-01

Full Text Available Blast furnace operation with low coke rate, high amount of auxiliary hydrocarbons and use of nut coke causes a change in coke quality requirements. In particular, not burned in the raceway residues of injected substances (char and ash can influence the coke behaviour. Therefore combustion efficiency of various organic wastes with and without pulverized coal injection (PCI and coal char has been investigated under the raceway simulation conditions. Mixing of various substances improves their combustion efficiency. Study on coke gasification by carbon dioxide in the presence of char showed that with the increase of char concentration, coke strength reduction becomes smaller. The reactivity of char with CO₂ is higher than that of coke. Therefore char is consumed preferentially. In presence of injected char, total pore volume in coke and its wear resistance were increased. Coke reactivity and microstructure in the presence of various kinds of ash has been studied. Many ash spheres were observed on the surface of coke matrix and its size was dependent on ash properties.

La operación del horno alto con una tasa baja de coque, una cantidad elevada de hidrocarburos auxiliares y el empleo de coque calibrado, origina un cambio en las necesidades de calidad del coque. En particular, pueden influir en el comportamiento del coque los residuos inquemados en el raceway (cavidad enfrente a las toberas del horno de las sustancias que se inyectan (char y cenizas. El char es el residuo de carbón que se origina después que el carbón libera sus sustancias volátiles. Por tanto, se ha investigado la eficiencia de la combustión de varios residuos orgánicos con y sin inyección de carbón pulverizado (ICP y char, bajo las condiciones de simulación del raceway. La mezcla de varias sustancias mejora la eficiencia a la combustión. El estudio de la gasificación del coque por el dióxido de carbono en la

Gasification of bio char from empty fruit bunch in a fluidized bed

International Nuclear Information System (INIS)

Nsamba Hussein Kisiki; Amran Mohammad Salleh; Wan Azlina; Hamdan Yusof

2010-01-01

Full text: Bio char from empty fruit bunch was gasified in a fluidized bed reactor using compressed air as a gasifying agent. The experiment was conducted in the temperature ranges of 500-850 degree Celsius and the equivalence ratio, temperature and size of the feedstock was varied. A series of parameters such as gas yield, overall carbon conversion, gas quality, and composition, were measured as a function of temperature, equivalence ratio and temperature. Results obtained were compared to the actual values of coal and other gasification feedstock reveal that, bio char has the potential to replace coal as a gasification agent in power plants .Hydrogen gas from bio char was also optimized during the experiment. There is great potential of making Hydrogen from Bio char through thermo chemical gasification It was observed that it has a very great potential of being upgraded to Fischer Tropsh fuels. There is a great opportunity of using this char from empty fruit bunch as an alternative fuel in power plants and all the adverse effects of coal gasification can be counteracted. (author)

Adsorption characteristics of SO{sub 2}, NO by steam activated biomass chars

Energy Technology Data Exchange (ETDEWEB)

Lu, Fei; Shu, Tong; Wang, Kuan; Lu, Ping [Nanjing Normal Univ. (China). School of Energy and Mechanical Engineering

2013-07-01

Wheat straw and rice husk collected from the suburb of Nanjing, China, were prepared to different kinds of steam activated biomass-based chars, and the adsorption characteristics of the biomass-based chars was carried out in a fixed bed reactor. The specific surface area and pore structure of different biomass chars were measured by nitrogen adsorption-desorption analysis instrument at 77K. The effects of biomass type, pyrolysis temperature, heating rate, activation temperature and concentration of SO{sub 2}, NO on the adsorption efficiency of SO{sub 2}, NO were analyzed. The results indicated that the steam activation has significant effects on the specific surface area, total pore volume and micro-morphology of biomass chars by improving the internal structure. The adsorption efficiency of SO{sub 2}, NO increased with the decreasing of SO{sub 2}, NO concentration in the experimental range. The optimal condition of char preparation (873K, fast pyrolysis) and steam activation (1,073K) was proposed based on the adsorption efficiency and adsorption volume of SO{sub 2}, NO. It builds a theoretical basis for industrial applications of biomass.

The kinetics of combustion of chars derived from sewage sludge

Energy Technology Data Exchange (ETDEWEB)

J.S. Dennis; R.J. Lambert; A.J. Milne; S.A. Scott; A.N. Hayhurst [University of Cambridge, Cambridge (United Kingdom). Department of Chemical Engineering

2005-02-01

Experiments have been conducted to determine the combustion characteristics of sewage sludge chars in electrically heated beds of silica sand fluidised by air. The effects of the initial size of the char particles, the temperature of the bed and the concentration of (O{sub 2}) in the fluidising gas were investigated. Also, the temperatures of burning particles were measured with embedded thermocouples. The kinetics of combustion were measured at temperatures low enough for the CO formed by initial reaction between the carbon and oxygen to burn at some distance away from the particle. It is probable that the lower value is closer to the actual value, thought to be 135{+-}15 kJ/mol, reflecting the catalytic nature of the ash skeleton on which the carbon is supported. It was possible to obtain good agreement between measured burnout times and those predicted using the grain model of Szekely J, Evans JW, Sohn HY. Gas-solid reactions. New York: Academic Press; 1976, for the case where the kinetics are controlled by a combination of: (i) external mass transfer of oxygen from the particulate phase to the external surface of the burning char particle, (ii) diffusion of oxygen from the external surface into the porous matrix to the surfaces of grains, of which the solid is composed, and (iii) diffusion of oxygen into the microporous grains, where reaction occurs with the carbon. It was found that, for particles with diameters of 2 mm or larger, the initial rates of reaction, for bed temperatures in excess of 750{degree}C, are dominated by external mass transfer. 22 refs., 8 figs., 1 tab.

Cow bones char as a green sorbent for fluorides removal from aqueous solutions: batch and fixed-bed studies.

Science.gov (United States)

Nigri, Elbert M; Cechinel, Maria Alice P; Mayer, Diego A; Mazur, Luciana P; Loureiro, José M; Rocha, Sônia D F; Vilar, Vítor J P

2017-01-01

Cow bone char was investigated as sorbent for the defluoridation of aqueous solutions. The cow bone char was characterized in terms of its morphology, chemical composition, and functional groups present on the bone char surface using different analytical techniques: SEM, EDS, N 2 -BET method, and FTIR. Batch equilibrium studies were performed for the bone chars prepared using different procedures. The highest sorption capacities for fluoride were obtained for the acid washed (q = 6.2 ± 0.5 mg/g) and Al-doped (q = 6.4 ± 0.3 mg/g) bone chars. Langmuir and Freundlich models fitted well the equilibrium sorption data. Fluoride removal rate in batch system is fast in the first 5 h, decreasing after this time until achieving equilibrium due to pore diffusion. The presence of carbonate and bicarbonate ions in the aqueous solution contributes to a decrease of the fluoride sorption capacity of the bone char by 79 and 31 %, respectively. Regeneration of the F-loaded bone char using 0.5 M NaOH solution leads to a sorption capacity for fluoride of 3.1 mg/g in the second loading cycle. Fluoride breakthrough curve obtained in a fixed-bed column presents an asymmetrical S-shaped form, with a slow approach of C/C 0  → 1.0 due to pore diffusion phenomena. Considering the guideline value for drinking water of 1.5 mg F - /L, as recommended by World Health Organization, the service cycle for fluoride removal was of 71.0 h ([F - ] feed  ∼ 9 mg/L; flow rate = 1 mL/min; m sorbent  = 12.6 g). A mass transfer model considering the pore diffusion was able to satisfactorily describe the experimental data obtained in batch and continuous systems.

Effects of pressure on morphology and structure of bio-char from pressurized entrained-flow pyrolysis of microalgae

Directory of Open Access Journals (Sweden)

Kristina Maliutina

2018-06-01

Full Text Available The present dataset describes the entrained-flow pyrolysis of Microalgae Chlorella vulgaris and the results obtained during bio-char characterization. The dataset includes a brief explanation of the experimental procedure, experimental conditions and the influence of pyrolysis conditions on bio-chars morphology and carbon structure. The data show an increase in sphericity and surface smoothness of bio-chars at higher pressures and temperatures. Data confirmed that the swelling ratio of bio-chars increased with pressure up to 2.0 MPa. Consequently, changes in carbon structure of bio-chars were investigated using Raman spectroscopy. The data showed the increase in carbon order of chars at elevated pressures. Changes in the chemical structure of bio-char as a function of pyrolysis conditions were investigated using FTIR analysis. Keywords: Microalgae, Bio-char, Particle swelling, Pressurized pyrolysis

Biochemical stability of sewage sludge chars and their impact on soil organic matter of a Mediterranean Cambisol

Science.gov (United States)

Paneque, Marina; María De la Rosa, José; Aragón, Carlos; Kern, Jürgen; Knicker, Heike

2016-04-01

Transformation of sewage sludge (SS) into char achieves sludge hygienisation, which is necessary prior its application into agricultural soils. The pyrolysis of SS increases its stability in a degree which depends on the thermal treatment used. Thus, chars produced by using hydrothermal carbonization are typically more stable than normal soil organic matter (SOM), but less stable than chars from dry pyrolysis (Libra et al., 2011). Addition of highly-recalcitrant SS-chars to soil will likely increase its carbon sequestration potential; however the fertilizing properties of SS may be compromised due to its alteration during the pyrolysis. The main goal of this work was to investigate the biochemical recalcitrance of two 13C-enriched SS-chars once applied in a Mediterranean Cambisol as well as to evaluate their impact on the SOM quality and carbon stability. Thus, we studied the distribution of 13C between plants and soil after the addition of the 13C-enriched chars (2 atm%) to the soil. Therefore, we performed a greenhouse incubation experiment, using a Mediterranean Cambisol as matrix and tested the following treatments: control (soil alone), raw SS, SS-hydrochar, SS-pyrochar. The SS was produced in a pilot-scale waste-water plant and enriched with 13C by the addition of 13C-glucose during the treatment. The amendment was only applied to the upper 2 cm of the soil matrix where it accounted for 5% of its dry weight. Per pot, 25 seeds of Lolium perenne were sowed and incubated under controlled conditions. The biomass production as well as the concentration of 13C in leaves and roots was determined after 1, 2 and 5 months. The partitioning of the 13C between soil and plant and its transformation into bioavailable forms were monitored by stable isotopic mass spectrometry. The 13C-enrichment of the chars allowed the use of solid-state 13C NMR spectroscopy as a means for the detection of chemical alterations of the chars during their aging. Libra J., Ro K., Kammann C

NMR studies on the chemical alteration of soil organic matter precursors during controlled charring

Science.gov (United States)

Knicker, Heike

2010-05-01

Beside the production of volatiles, vegetation fire transforms various amounts of labile organic components into recalcitrant dark colored and highly aromatic structures. They are incorporated into soils and are assumed to represent an important sink within the global carbon cycle. In order to elucidate the real importance of PyOM as a C-sink, a good understanding of its chemistry is crucial. Although several 'Black Carbon' (BC) models are reported, a commonly accepted view of the chemistry involved in its formation is still missing. Its biogeochemical recalcitrance is commonly associated with a highly condensed aromatic structure. However, recent studies indicated that this view may be oversimplified for PyOM derived from vegetation fire. In order to bring some more light on the structural properties of PyOM produced during vegetation fire, charred plant residues and model chars derived from typical plant macromolecules (casein, cellulose, lignin and condensed tannins) were subjected to controlled charring under oxic conditions (350°C and 450°C) and then characterized by nuclear magnetic resonance (NMR) spectroscopy and elemental analysis. Subsequently, the chemical features of the PyOM were related to its chemical recalcitrance as determined by chemical oxidation with acid potassium dichromate. Charring cellulose (350°C, 8 min) yielded in a low C-recovery (11%). Treating casein in the same way resulted in a survival of 62% of its C and 46% of its N. Comparable high C-recoveries are reported for lignin. After charring Lolium perenne, 34% of its N and C were recovered. NMR-spectroscopic studies revealed that for this sample most of the charred N and C occurred in pyrrole-type structures. Our studies further indicate that the aromatic skeleton of char accumulating after a vegetation fire must contain remains of the lignin backbone and considerable contributions of furans and anhydrosugars from thermally altered cellulose. Enhancing the temperature during the

The influence of wildfire severity on soil char composition and nitrogen dynamics

Science.gov (United States)

Rhoades, Charles; Fegel, Timothy; Chow, Alex; Tsai, Kuo-Pei; Norman, John, III; Kelly, Eugene

2017-04-01

Forest fires cause lasting ecological changes and alter the biogeochemical processes that control stream water quality. Decreased plant nutrient uptake is the mechanism often held responsible for lasting post-fire shifts in nutrient supply and demand, though other upland and in-stream factors also likely contribute to elevated stream nutrient losses. Soil heating, for example, creates pyrogenic carbon (C) and char layers that influence C and nitrogen (N) cycling. Char layer composition and persistence vary across burned landscapes and are influenced first by fire behavior through the temperature and duration of combustion and then by post-fire erosion. To evaluate the link between soil char and stream C and N export we studied areas burned by the 2002 Hayman Fire, the largest wildfire in Colorado, USA history. We compared soil C and N pools and processes across ecotones that included 1) unburned forests, 2) areas with moderate and 3) high wildfire severity. We analyzed 1-2 cm thick charred organic layers that remain visible 15 years after the fire, underlying mineral soils, and soluble leachate from both layers. Unburned soils released more dissolved organic C and N (DOC and DON) from organic and mineral soil layers than burned soils. The composition of DOC leachate characterized by UV-fluorescence, emission-excitation matrices (EEMs) and Fluorescence Regional Integration (FRI) found similarity between burned and unburned soils, underscoring a common organic matter source. Humic and fulvic acid-like fractions, contained in regions V and III of the FRI model, comprised the majority of the fluorescing DOM in both unburned and char layers. Similarity between two EEMs indices (Fluorescence and Freshness), further denote that unburned soils and char layers originate from the same source and are consistent with visual evidence char layers contain significant amounts of unaltered OM. However, the EEMs humification index (HIX) and compositional analysis with pyrolysis GCMS

Co-gasification of coal and biomass: Synergy, characterization and reactivity of the residual char.

Science.gov (United States)

Hu, Junhao; Shao, Jingai; Yang, Haiping; Lin, Guiying; Chen, Yingquan; Wang, Xianhua; Zhang, Wennan; Chen, Hanping

2017-11-01

The synergy effect between coal and biomass in their co-gasification was studied in a vertical fixed bed reactor, and the physic-chemical structural characteristics and gasification reactivity of the residual char obtained from co-gasification were also investigated. The results shows that, conversion of the residual char and tar into gas is enhanced due to the synergy effect between coal and biomass. The physical structure of residual char shows more pore on coal char when more biomass is added in the co-gasification. The migration of inorganic elements between coal and biomass was found, the formation and competitive role of K 2 SiO 3 , KAlSiO 4 , and Ca 3 Al 2 (SiO 4 ) 3 is a mechanism behind the synergy. The graphization degree is enhanced but size of graphite crystallite in the residual char decreases with biomass blending ratio increasing. TGA results strongly suggest the big difference in the reactivity of chars derived from coal and biomass in spite of influence from co-gasification. Copyright © 2017 Elsevier Ltd. All rights reserved.

History, Violence and Poetics: Saint-John Perse and René Char

Directory of Open Access Journals (Sweden)

Nathan Bracher

1991-06-01

Full Text Available This essay explores the parallel yet opposite stances taken both personally and textually by Perse and Char with respect to drama of World War II. While Perse remained disdainfully aloof from public affairs after the defeat and proclaimed in his poetry his solidarity with all humanity, Char explicitly linked his writing to events, yet sought to create a human space removed from history's upheavals. Striving to transcend the vicissitudes of individual existence, Perse celebrates an epic vision of history that overlooks and even condones its violence. Focusing on the inconsistent, fragmentary nature of existence, Char prevents us from having any teleological delusions concerning war.

Volatilisation and catalytic effects of alkali and alkaline earth metallic species during the pyrolysis and gasification of Victorian brown coal. Part IV. Catalytic effects of NaCl and ion-exchangeable Na in coal on char reactivity

Energy Technology Data Exchange (ETDEWEB)

Dimple Mody Quyn; Hongwei Wu; Jun-ichiro Hayashi; Chun-Zhu Li, [Monash University, Monash, Vic. (Australia). CRC for Clean Power from Lignite, Department of Chemical Engineering

2003-03-01

The purpose of this study is to investigate the catalytic effects of Na as NaCl or as sodium carboxylates ( COONa) in Victorian brown coal on the char reactivity. A Na-exchanged coal and a set of NaCl-loaded coal samples prepared from a Loy Yang brown coal were pyrolysed in a fluidised-bed/fixed-bed reactor and in a thermogravimetric analyser (TGA). The reactivities of the chars were measured in air at 400{sup o}C using the TGA. The experimental data indicate that the Na in coal as NaCl and as sodium carboxylates ( COONa) had very different catalytic effects on the char reactivity. It is the chemical form and dispersion of Na in char, not in coal, that govern the catalytic effects of Na. For the Na-form (Na-exchanged) coal, the char reactivity increased with increasing pyrolysis temperature from 500 to 700{sup o}C and then decreased with pyrolysis temperature from 700 to 900{sup o}C. The increase in reactivity with pyrolysis temperature (500 700{sup o}C) is mainly due to the changes in the relative distribution of Na in the char matrix and on the pore surface. For the NaCl-loaded coals, when Cl was released during pyrolysis or gasification, the Na originally present in coal as NaCl showed good catalytic effects for the char gasification. Otherwise, Cl would combine with Na in the char to form NaCl during gasification, preventing Na from becoming an active catalyst. Controlling the pyrolysis conditions to favour the release of Cl can be a promising way to transform NaCl in coal into an active catalyst for char gasification. 38 refs., 5 figs.

The effect of 150μm expandable graphite on char expansion of intumescent fire retardant coating

International Nuclear Information System (INIS)

Ullah, Sami; Shariff, A. M.; Bustam, M. A.; Ahmad, Faiz

2014-01-01

Intumescent is defined as the swelling of certain substances to insulate the underlying substrate when they are heated. In this research work the effect of 150μm expandable graphite (EG) was studied on char expansion, char morphology and char composition of intumescent coating formulations (ICFs). To study the expansion and thermal properties of the coating, nine different formulations were prepared. The coatings were tested at 500 °C for one hour and physically were found very stable and well bound with the steel substrate. The morphology was studied by Scanning Electron Microscopy (SEM). The char composition was analysed by X-ray Diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) techniques. EG above than 10.8wt% expands the char abruptly with uniform network structure and affect the outer surface of the char

The effect of 150μm expandable graphite on char expansion of intumescent fire retardant coating

Energy Technology Data Exchange (ETDEWEB)

Ullah, Sami, E-mail: samichemist1@gmail.com; Shariff, A. M., E-mail: azmish@petronas.com.my, E-mail: azmibustam@petronas.com.my; Bustam, M. A., E-mail: azmish@petronas.com.my, E-mail: azmibustam@petronas.com.my [Research Center for Carbon Dioxide Capture, Department of Chemical Engineering, Universiti Techologi PETRONAS, Bandar Sri Iskandar, Tronoh 31750 Perak (Malaysia); Ahmad, Faiz, E-mail: faizahmadster@gmail.com [Department of Mechanical Engineering, Universiti Techologi PETRONAS, Bandar Sri Iskandar, Tronoh 31750 Perak (Malaysia)

2014-10-24

Intumescent is defined as the swelling of certain substances to insulate the underlying substrate when they are heated. In this research work the effect of 150μm expandable graphite (EG) was studied on char expansion, char morphology and char composition of intumescent coating formulations (ICFs). To study the expansion and thermal properties of the coating, nine different formulations were prepared. The coatings were tested at 500 °C for one hour and physically were found very stable and well bound with the steel substrate. The morphology was studied by Scanning Electron Microscopy (SEM). The char composition was analysed by X-ray Diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) techniques. EG above than 10.8wt% expands the char abruptly with uniform network structure and affect the outer surface of the char.

Combustion Characteristics Of Agricultural Waste-Coal Char Blends

International Nuclear Information System (INIS)

Akpabio, I. O; Danbature W

2002-01-01

Shortage of petroleum products, depletion of huge forest reserves for fuel purposes with its attendant erosion problems and other environmental considerations have necessitated investigations into other sources of fuel. In this wise. a set of seven types of briquettes were prepared from agricultural wastes such as rice husk, maize husk and saw-dust and blends of carbonized coal char. Strong and well-formed briquettes with good combustion characteristics were obtained. The results obtained from water boiling tests show that 2 litres of water could be boiled just under 23 minutes. Moisture contents and strengths of these briquettes were also determined and are discussed. The results show that wastes could be converted into useful fuel

Cesium in Arctic char lakes - effects of the Chernobyl accident

International Nuclear Information System (INIS)

Hammar, J.; Notter, M.; Neumann, G.

1991-01-01

Fallout radiocesium from the Chernobyl accident caused extensive contamination in a region of previously well studied alpine lake ecosystems in northern Sweden. Levels of Cs-137 in the barren catchment basins reached 20-50 kBq/m 2 during 1986. The distribution, pathways and major transport mechanisms of radiocesium through the lake ecosystems were studied during 1986-1990. Levels of Cs-137, Cs-134 and K-40 in water, surface sediment, detritus (sediment traps) and different trophic levels of the food chains of Arctic char (Salvelinus alpinus) and brown trout (Salmo trutta) were monitored in a series of lakes forming a matrix of 4 natural lakes and 3 lake reservoirs, with or without the introduced new fish food organism, Mysis relicta. The reservoirs were found to act as sinks for radiocesium with extensive accumulation recorded in water, detritus, sediment, invertebrates and salmonids. Whereas concentrations in water and biota have declined from the extreme peak levels in 1986-1987, the levels in surface sediment increased extensively until fall of 1988. The concentration of Cs-137 in fish populations feeding on benthic invertebrates, i.e. mysids and amphipods, were significantly higher than in planktivorous fish. During the three first winters a significant increase in levels of Cs-137 in winter active Arctic char were recorded, whereas the levels declined during the succeeding summers. The introduced Mysis relicta were found to enhance the transport of Cs-137 from zooplankton and settling particles to Arctic char and brown trout. The results suggest a successive change in transport of radiocesium from water via zooplankton to planktivorous fish during the early summer of 1986 to post-depositional mobilization via benthic organisms to benthic fish in successive years. (213 refs.) (au)

Production of activated carbon from TCR char

Science.gov (United States)

Stenzel, Fabian; Heberlein, Markus; Klinner, Tobias; Hornung, Andreas

2016-04-01

The utilization of char for adsorptive purposes is known since the 18th century. At that time the char was made of wood or bones and used for decoloration of fluids. In the 20th century the production of activated carbon in an industrial scale was started. The today's raw materials for activated carbon production are hard coal, peat, wood or coconut shells. All these materials entail costs especially the latter. Thus, the utilization of carbon rich residues (biomass) is an interesting economic opportunity because it is available for no costs or even can create income. The char is produced by thermo-catalytic reforming (TCR®). This process is a combination of an intermediate pyrolysis and subsequently a reforming step. During the pyrolysis step the material is decomposed in a vapor and a solid carbon enriched phase. In the second step the vapor and the solid phase get in an intensive contact and the quality of both materials is improved via the reforming process. Subsequently, the condensables are precipitated from the vapor phase and a permanent gas as well as oil is obtained. Both are suitable for heat and power production which is a clear advantage of the TCR® process. The obtained biochar from the TCR® process has special properties. This material has a very low hydrogen and oxygen content. Its stability is comparable to hard coal or anthracite. Therefore it consists almost only of carbon and ash. The latter depends from input material. Furthermore the surface structure and area can be influenced during the reforming step. Depending from temperature and residence time the number of micro pores and the surface area can be increased. Preliminary investigations with methylene blue solution have shown that a TCR® char made of digestate from anaerobic digestion has adsorptive properties. The decoloration of the solution was achieved. A further influencing factor of the adsorption performance is the particle size. Based on the results of the preliminary tests a

Ultrasonic Characterisation of Epoxy Resin/Polyethylene Terephthalate (PET Char Powder Composites

Directory of Open Access Journals (Sweden)

Imran ORAL

2016-11-01

Full Text Available This study is carried out in order to determine the elastic properties of the Epoxy Resin (ER / Polyethylene terephthalate (PET Char Powder Composites by ultrasonic wave velocity measurement method. Plastic waste was recycled as raw material for the preparation of epoxy composite materials. The supplied chars were mixed with epoxy resin matrix at weight percentages of 10 %, 20 % and 30 % for preparing ER/PET Char Powder (PCP composites. The effect of PET char powder on the elastic properties of ER/PCP composites were investigated by ultrasonic pulse-echo method. According to the obtained results, the composition ratio of 80:20 is the most appropriate composition ratio, which gave the highest elastic constants values for ER/PCP composites. On the other hand, the best electrical conductivity value was obtained for 70:30 composition ratio. It was observed that ultrasonic shear wave velocity correlated more perfectly than any other parameters with hardness.DOI: http://dx.doi.org/10.5755/j01.ms.22.4.12190

Endotoxin Removal from Water Using Heterogenus Catalytic Ozonation by Bone Char

Directory of Open Access Journals (Sweden)

Abas Rezaee

2011-10-01

Full Text Available The endotoxin is one of pollutants with lipopolysaccharide structure which release from gram negative bacteria and cyanobacters. The aim of this study was removal of endotoxin from water using catalytic ozonation by bone char. The endotoxin for experiments have extracted from Escherichia coli bacterium cell wall by Stefan and Jan method. Chromogenic limulus ambusite lysate method in 405-410 nm wave length was used for analysing of endotoxin. The ozone have analysed by potassium iodine method. Results: Results of the research shown endotoxin removal rates using heterogenous catalytic ozonation were 6.0 Eu/ml.min and 0.5 Eu/ml.min for grey bone char and white bone char, respectively. The efficency of the process was found eighty percent. Primary concentration of basic compounds had no effect on endotoxin removal rate. Therefore, endotoxin removal kinetic of reaction is a zero order reaction. This study revealed that ozonation process using bone char is more efficient than other proposed methods such as ozonation or chlorination and can be used successfully for endotoxin removal from water as a efficient method.

Preoxidation and Activation of the Lignin Char: Carbonization and Oxidation Procedures

Directory of Open Access Journals (Sweden)

Saloua Sebbahi

2014-01-01

Full Text Available A comprehensive process of pretreatment and oxidation of lignin char was developed to optimize the production of activated carbon. The lignin char was obtained by carbonization of lignin under nitrogen at 600°C for 2 hours. The optimum time and temperature used to oxidize the char without destruction were, respectively, 6 hours and 245°C. The oxygen improves the reactivity of the sample in CO2 and evolved the sample of a thermoplastic behaviour to a thermosetting behaviour. The oxygenation in air of the lignin char does not change the mode of deformation acquired by the material during the carbonization. The preoxidized coal reacts more than the nonoxidized coal during the CO2 activation, whereas the reduction in volume in the first case is smaller than in the second. The preoxidized and then activated carbon shows the formation and the development of microporosity at the expense of macroporosity. This microstructure is one of the main characteristics of activated carbon, which can be used as adsorbent for different pollutants.

Influence of pressure on pyrolysis of black liquor: 2. Char yields and component release.

Science.gov (United States)

Whitty, Kevin; Kullberg, Mika; Sorvari, Vesa; Backman, Rainer; Hupa, Mikko

2008-02-01

This is the second in a series of papers concerning the behavior of black liquor during pyrolysis at elevated pressures. Two industrial black liquors were pyrolyzed under pressurized conditions in two laboratory-scale devices, a pressurized single-particle reactor and a pressurized grid heater. Temperatures ranging between 650 and 1100 degrees C and pressures in the range 1-20 bar were studied. Char yields were calculated and based on analysis of some of the chars the fate of carbon, sodium, potassium and sulfur was determined as a function of pyrolysis pressure. At temperatures below 800 degrees C little variation in char yield was observed at different pressures. At higher temperatures char yield increased with pressure due to slower decomposition of sodium carbonate. For the same reason, sodium release decreased with pressure. Sulfur release, however, increased with pressure primarily because there was less opportunity for its capture in the less-swollen chars.

Adsorption of Pb(II by Activated Pyrolytic Char from Used Tire

Directory of Open Access Journals (Sweden)

Lu Ping

2016-01-01

Full Text Available As a renewable resource, the pyrolytic char derived from used tire has promising adsorption capacities owing to its similar structure and properties with active carbon. The purification and activation of the pyrolytic char from used tire, as well as the application of this material in the adsorption of Pb(II in water is conducted. The influences on the adsorption capacity by temperature and pH value are investigated and discussed; the adsorption thermodynamics and kinetics are also studied. The results show that the pyrolytic char from used tire has remarkable adsorption capacity for Pb(II, and the adsorption is an endothermic process complying with the Langmuir isotherm. The adsorption kinetics is a pseudo second-order reaction.

Mixed waste treatment using the ChemChar thermolytic detoxification technique

Energy Technology Data Exchange (ETDEWEB)

Kuchynka, D.

1995-12-31

The diversity of mixed waste matrices contained at Department of Energy sites that require treatment preclude a single, universal treatment technology capable of handling sludges, solids, heterogeneous debris, aqueous and organic liquids and soils. Versatility of the treatment technology, volume reduction and containment of the radioactive component of the mixed waste streams are three criteria to be considered when evaluating potential treatment technologies. The ChemChar thermolytic detoxification process being developed under this R and D contract is a thermal, chemically reductive technology that converts the organic portion of a mixed waste stream to an energy-rich synthesis gas while simultaneously absorbing volatile inorganic species (metals and acid gases) on a macroporous, carbon-based char. The latter is mixed with the waste stream prior to entering the reactor. Substoichiometric amounts of oxidant are fed into the top portion of the cylindrical reactor generating a thin, radial thermochemical reaction zone. This zone generates all the necessary heat to promote the highly endothermic reduction of the organic components in the waste in the lower portion of the reactor, producing, principally, hydrogen and carbon monoxide. The solid by-product is a regenerated carbon char that, depending on the inorganic loading, is capable for reuse. The in situ scrubbing of contaminants by the char within the reactor coupled with a char filter for final polishing produce an exceptionally clean synthesis gas effluent suitable for on-site generation of heat, steam or electricity. Despite the elevated temperatures in the thermochemical reaction zone, the reductive nature of the process precludes formation of nitrogen oxides and halogenated organic compound by-products.

Mixed waste treatment using the ChemChar thermolytic detoxification technique

International Nuclear Information System (INIS)

Kuchynka, D.

1995-01-01

The diversity of mixed waste matrices contained at Department of Energy sites that require treatment preclude a single, universal treatment technology capable of handling sludges, solids, heterogeneous debris, aqueous and organic liquids and soils. Versatility of the treatment technology, volume reduction and containment of the radioactive component of the mixed waste streams are three criteria to be considered when evaluating potential treatment technologies. The ChemChar thermolytic detoxification process being developed under this R and D contract is a thermal, chemically reductive technology that converts the organic portion of a mixed waste stream to an energy-rich synthesis gas while simultaneously absorbing volatile inorganic species (metals and acid gases) on a macroporous, carbon-based char. The latter is mixed with the waste stream prior to entering the reactor. Substoichiometric amounts of oxidant are fed into the top portion of the cylindrical reactor generating a thin, radial thermochemical reaction zone. This zone generates all the necessary heat to promote the highly endothermic reduction of the organic components in the waste in the lower portion of the reactor, producing, principally, hydrogen and carbon monoxide. The solid by-product is a regenerated carbon char that, depending on the inorganic loading, is capable for reuse. The in situ scrubbing of contaminants by the char within the reactor coupled with a char filter for final polishing produce an exceptionally clean synthesis gas effluent suitable for on-site generation of heat, steam or electricity. Despite the elevated temperatures in the thermochemical reaction zone, the reductive nature of the process precludes formation of nitrogen oxides and halogenated organic compound by-products

Feasibility of mercury removal from simulated flue gas by activated chars made from poultry manures.

Science.gov (United States)

Klasson, K Thomas; Lima, Isabel M; Boihem, Larry L; Wartelle, Lynda H

2010-12-01

Increased emphasis on reduction of mercury emissions from coal fired electric power plants has resulted in environmental regulations that may in the future require application of activated carbons as mercury sorbents for mercury removal. At the same time, the quantity of poultry manure generated each year is large and technologies that take advantage of the material should be explored. The purpose of the work was to obtain preliminary data to investigate if activated chars made from different poultry manures could adsorb mercury from simulated flue gas. In laboratory experiments, activated chars made from chicken cake and litter removed mercury from the gas as well as a commercial alternative. It was also found that acid-washing these chars after activation may improve pore structure but does not influence the mercury removal efficiency. Activated chars were also made from turkey cake and litter. These raw materials produced activated chars with similar pore structure as those made from chicken manure, but they did not adsorb mercury as well. Acid-washing the turkey manure-based chars improved their performance, but this step would add to the cost of production. Preliminary evaluations suggest that unwashed activated chars may cost as little as $0.95/kg to produce. Published by Elsevier Ltd.

Mixed waste treatment using the ChemChar thermolytic detoxification technique

Energy Technology Data Exchange (ETDEWEB)

Kuchynka, D. [Mirage Systems, Sunnyvale, CA (United States)

1995-10-01

The diversity of mixed waste matrices contained at Department of Energy sites that require treatment preclude a single, universal treatment technology capable of handling sludges, solids, heterogeneous debris, aqueous and organic liquids and soils. This report describes the ChemChar thermolytic detoxification process. The process is a thermal, chemically reductive technology that converts the organic portion of mixed wastes to a synthesis gas, while simultaneously absorbing volatile inorganics on a carbon-based char.

Prediction of the burnout behaviour of chars derived from coal-biomass blends

Energy Technology Data Exchange (ETDEWEB)

Tao Wu; Mei Gong; Edward Lester [University of Nottingham, Nottingham (United Kingdom). School of Chemical, Environmental and Mining Engineering

2007-07-01

Nowadays, biomass has been considered an alternative fuel to coal and is being used in power plants to replace part of coal used. This study is to investigate the potential of burning biomass with coal and its impacts on burnout levels. Daw Mill coal was selected for burnout modelling together with three biomasses, Cereal, PKE and Olive Cake. Chars were prepared (75-106 micron) and characterised using image analysis methods as in input data into the char burnout model (ChB) which was adapted to allow the prediction of char burnout of biomass-coal blends under typical pf combustion conditions. The burnout performance of four blend compositions for each biomass were modelled (5%, 10%, 20% and 30%). In practice, the low heating-value of biomass produces a lower flame temperature which can lead to lower levels of char burn-out. The effect is closely linked with the type of biomass used. 36 refs., 4 figs., 1 tab.

Influence of post-treatment strategies on the properties of activated chars from broiler manure.

Science.gov (United States)

Lima, Isabel M; Boykin, Debbie L; Thomas Klasson, K; Uchimiya, Minori

2014-01-01

There are a myriad of carbonaceous precursors that can be used advantageously to produce activated carbons or chars, due to their low cost, availability and intrinsic properties. Because of the nature of the raw material, production of granular activated chars from broiler manure results in a significant ash fraction. This study was conducted to determine the influence of several pre- and post-treatment strategies in various physicochemical and adsorptive properties of the resulting activated chars. Pelletized samples of broiler litter and cake were pyrolyzed at 700 °C for 1h followed by a 45 min steam activation at 800 °C at different water flow rates from 1 to 5 mL min(-1). For each activation strategy, samples were either water-rinsed or acid-washed and rinsed or used as is (no acid wash/rinse). Activated char's physicochemical and adsorptive properties towards copper ions were selectively affected by both pre- and post-treatments. Percent ash reduction after either rinsing or acid washing ranged from 1.1 to 15.1% but washed activated chars were still alkaline with pH ranging from 8.4 to 9.1. Acid washing or water rinsing had no significant effect in the ability of the activated char to adsorb copper ions, however it significantly affected surface area, pH, ash content and carbon content. Instead, manure type (litter versus cake) and the activation water flow rate were determining factors in copper ion adsorption which ranged from 38 mg g(-1) to 104 mg g(-1) of activated char. Moreover, strong positive correlations were found between copper uptake and concentration of certain elements in the activated char such as phosphorous, sulfur, calcium and sodium. Rinsing could suffice as a post treatment strategy for ash reduction since no significant differences in the carbon properties were observed between rinsed and acid wash treatments. Published by Elsevier Ltd.

Two-step microalgal biodiesel production using acidic catalyst generated from pyrolysis-derived bio-char

International Nuclear Information System (INIS)

Dong, Tao; Gao, Difeng; Miao, Chao; Yu, Xiaochen; Degan, Charles; Garcia-Pérez, Manuel; Rasco, Barbara; Sablani, Shyam S.; Chen, Shulin

2015-01-01

Highlights: • Highly active catalyst was prepared using bio-char co-produced in Auger pyrolysis. • Catalyst inhibitors in crude oil were effectively removed by a practical refinery process. • Free fatty acids (FFA) content in refined microalgal oil was reduced to less than 0.5%. • A total fatty acid methyl ester (FAME) yield of 99% was obtained via a two-step process. • The inexpensive bio-char catalyst is superior to Amberlyst-15 in pre-esterification. - Abstract: An efficient process for biodiesel production from fast-refined microalgal oil was demonstrated. A low cost catalyst prepared from pyrolysis-derived bio-char, was applied in pre-esterification to reduce free fatty acid (FFA) content. Results showed that the bio-char catalyst was highly active in esterification; however, the performance of the catalyst significantly reduced when crude microalgal oil was used as feedstock. To solve the problem caused by catalyst-fouling, a fast and scalable crude oil refinery procedure was carried out to remove chlorophyll and phospholipids that might degrade the catalyst and the quality of biodiesel. The activity and reusability of bio-char catalyst were remarkably improved in the fast-refined oil. FFA content in the refined microalgal oil was reduced to less than 0.5% after pre-esterification. The bio-char catalyst could be reused for 10 cycles without dramatic loss in activity. The pre-esterification fits the first-order kinetic reaction with activation energy of 42.16 kJ/mol. The activity of bio-char catalyst was superior to commercial Amberlyst-15 under the same reaction condition. A total fatty acid methyl ester (FAME, namely biodiesel) yield of 99% was obtained following the second-step CaO-catalyzed transesterification. The cost-effective bio-char catalyst has great potential for biodiesel production using feedstocks having high FFA content.

Reactivity of chars prepared from the pyrolysis of a Victorian lignite under a wide range of conditions

Energy Technology Data Exchange (ETDEWEB)

Wu, H.; Mody, D.; Li, C.; Hayashi, J.; Chiba, T. [Monash University, Vic. (Australia). CRC for Clean Power from Lignite, Dept. of Chemical Engineering

2000-07-01

A Loy Yang lignite sample was pyrolysed under a wide range of experimental conditions using a wire-mesh reactor, a fluidised-bed reactor, a drop-tube reformer and a thermogravimetric analyser (TGA). The reactivity of these char samples in CO{sub 2} and air was measured in the TGA as well as in the fluidised-bed reactor. A sample prepared by the physical impregnation of NaCl into the lignite was also used in order to investigate the effect of NaCl in the lignite on the reactivity of the resulting char. Our experimental results indicate that, due to the volatilisation of a substantial fraction of Na in the lignite substrate during pyrolysis, the true catalytic activity of the Na in the lignite substrate should be evaluated by measuring the sodium content in the char after pyrolysis. The char reactivity measured in situ in the fluidised-bed reactor was compared with that of the same char measured separately in the TGA after re-heating the char sample to the same temperature as that in the fluidised-bed. It was found that the re-heating of the char in the TGA reduced the char reactivity.

Catalytic ozonation of ammonia using biomass char and wood fly ash.

Science.gov (United States)

Kastner, James R; Miller, Joby; Kolar, Praveen; Das, K C

2009-05-01

Catalytic ozonation of gaseous ammonia was investigated at room temperature using wood fly ash (WFA) and biomass char as catalysts. WFA gave the best results, removing ammonia (11 ppmv NH(3), 45% conversion) at 23 degrees C at a residence time of 0.34 s, using 5 g of catalyst or ash at the lowest ozone concentration (62 ppmv). Assuming pseudo zero order kinetics in ozone, a power rate law of -r(NH3) = 7.2 x 10(-8) C(NH3)(0.25) (r, mol g(-1)s(-1), C(NH3)molL(-1)) was determined at 510 ppmv O(3) and 23 degrees C for WFA. Water vapor approximately doubled the oxidation rate using WFA and catalytic ozonation activity was not measured for the char without humidifying the air stream. Overall oxidation rates using the crude catalysts were lower than commercial catalysts, but the catalytic ozonation process operated at significantly lower temperatures (23 vs. 300 degrees C). Nitric oxide was not detected and the percentage of NO(2) formed from NH(3) oxidation ranged from 0.3% to 3% (v/v), with WFA resulting in the lowest NO(2) level (at low O(3) levels). However, we could not verify that N(2)O was not formed, so further research is needed to determine if N(2) is the primary end-product. Additional research is required to develop techniques to enhance the oxidation activity and industrial application of the crude, but potentially inexpensive catalysts.

Type of litter determines the formation and properties of charred material during wildfires

Science.gov (United States)

Chavez, Bruno; Fonturbel, M. Teresa; Salgado, Josefa; García-Oliva, Felipe; Vega, Jose A.; Merino, Agustin

2014-05-01

Wildfire is one of the most important disturbances all over the World, affecting both the amount and composition of forest floor and mineral soils. In comparison with unburnt areas, wildfire-affected forest floor usually shows lower contents of labile C compounds and higher concentrations of recalcitrant aromatic forms. These changes in composition can have important impact on biogeochemical cycles and therefore ecosystem functions. Although burning of different types of litter can lead to different amount and types of pyrogenic compounds, this aspect has not been evaluated yet. The effect of wildfire on SOM composition and stability were evaluated in five major types of non-wood litter in Mediterranean ecosystems: Pinus nigra, E. arborea, P. pinaster, U. europaeus and Eucalyptus globulus. In each of these ecosystems, forest floor samples from different soil burn severities were sampled. Soil burnt severities were based on visual signs of changes in forest floor and deposition of ash. Pyrogenic carbon quality were analysed using elementary analysis, solid-state 13 C nuclear magnetic resonance spectroscopy, Reflectance Infrared Fourier Transform (FTIR) and thermal analysis (simultaneous DSC-TG). The study showed that the different types of litter influenced the formation and characteristics of charred material. They differed in the temperature at which they start to be formed, the amounts of charred compounds and in their chemical composition. The resulting charred materials from the different litter, showed an important variability in the degree of carbonitation/aromatization. Unlike the biochar obtained through pyrolysis of woody sources, which contains exclusively aromatic structures, in the charred material produced in some litter, lignin, cellulose and even cellulose persist even in the high soil burnt severity. Coinciding with increases in aromatic contents, important decreases in atomic H/C and O/C ratios were recorded. However, the values found in some

Structural evolution of biomass char and its effect on the gasification rate

DEFF Research Database (Denmark)

Fatehi, Hesameddin; Bai, Xue Song

2017-01-01

The evolution of char porous structure can affect the conversion rate of the char by affecting the intra-particle transport, especially in the zone II conversion regime. A multi-pore model based on the capillary pore theory is developed to take into account different conversion rates for pores wi...

Role of oxygen-containing functional groups in forest fire-generated and pyrolytic chars for immobilization of copper and nickel.

Science.gov (United States)

Esfandbod, Maryam; Merritt, Christopher R; Rashti, Mehran Rezaei; Singh, Balwant; Boyd, Sue E; Srivastava, Prashant; Brown, Christopher L; Butler, Orpheus M; Kookana, Rai S; Chen, Chengrong

2017-01-01

Char as a carbon-rich material, can be produced under pyrolytic conditions, wildfires or prescribed burn offs for fire management. The objective of this study was to elucidate mechanistic interactions of copper (Cu 2+ ) and nickel (Ni 2+ ) with different chars produced by pyrolysis (green waste, GW; blue-Mallee, BM) and forest fires (fresh-burnt by prescribed fire, FC; aged char produced by wild fire, AC). The pyrolytic chars were more effective sorbents of Cu 2+ (∼11 times) and Ni 2+ (∼5 times) compared with the forest fire chars. Both cross-polarization (CPMAS-NMR) and Bloch decay (BDMAS-NMR) 13 C NMR spectroscopies showed that forest fire chars have higher woody components (aromatic functional groups) and lower polar groups (e.g. O-alkyl C) compared with the pyrolytic chars. The polarity index was greater in the pyrolytic chars (0.99-1.34) than in the fire-generated chars (0.98-1.15), while aromaticity was lower in the former than in the latter. Fourier transform infrared (FTIR) and Raman spectroscopies indicated the binding of carbonate and phosphate with both Cu 2+ and Ni 2+ in all chars, but with a greater extent in pyrolytic than forest fire-generated chars. These findings have demonstrated the key role of char's oxygen-containing functional groups in determining their sorption capacity for the Cu 2+ and Ni 2+ in contaminated lands. Copyright © 2016 Elsevier Ltd. All rights reserved.

Intrinsic reaction kinetics of coal char combustion by direct measurement of ignition temperature

International Nuclear Information System (INIS)

Kim, Ryang-Gyoon; Jeon, Chung-Hwan

2014-01-01

A wire heating reactor that can use a synchronized experimental method was developed to obtain the intrinsic kinetics of large coal char particles ranging in size from 0.4 to 1 mm. This synchronization system consists of three parts: a thermocouple wire for both heating and direct measurement of the particle temperature, a photodetector sensor for determining ignition/burnout points by measuring the intensity of luminous emission from burning particles, and a high-speed camera–long-distance microscope for observing and recording the movement of luminous zone directly. Coal char ignition was found to begin at a spot on the particle's external surface and then moved across the entire particle. Moreover, the ignition point determined according to the minimum of dT/dt is a spot point and not a full growth point. The ignition temperature of the spot point rises as the particle diameter increases. A spot ignition model, which describes the ignition in terms of the internal conduction and external/internal oxygen diffusion, was then developed to evaluate the intrinsic kinetics and predict the ignition temperature of the coal char. Internal conduction was found to be important in large coal char particles because its effect becomes greater than that of oxygen diffusion as the particle diameter increases. In addition, the intrinsic kinetics of coal char obtained from the spot ignition model for two types of coal does not differ significantly from the results of previous investigators. -- Highlights: • A novel technique was used to measure the coal char particle temperature. • The ignition point determined from a dT/dt minimum is a spot ignition point. • A spot ignition model was suggested to analyze the intrinsic reaction kinetics of coal char. • Internal conduction has to be considered in order to evaluate the intrinsic kinetics for larger particle (above 1 mm)

Pyrolysis conditions and ozone oxidation effects on ammonia adsorption in biomass generated chars.

Science.gov (United States)

Kastner, James R; Miller, Joby; Das, K C

2009-05-30

Ammonia adsorbents were generated via pyrolysis of biomass (peanut hulls and palm oil shells) over a range of temperatures and compared to a commercially available activated carbon (AC) and solid biomass residuals (wood and poultry litter fly ash). Dynamic ammonia adsorption studies (i.e., breakthrough curves) were performed using these adsorbents at 23 degrees C from 6 to 17 ppmv NH(3). Of the biomass chars, palm oil char generated at 500 degrees C had the highest NH(3) adsorption capacity (0.70 mg/g, 6 ppmv, 10% relative humidity (RH)), was similar to the AC, and contrasted to the other adsorbents (including the AC), the NH(3) adsorption capacity significantly increased if the relative humidity was increased (4 mg/g, 7 ppmv, 73% RH). Room temperature ozone treatment of the chars and activated carbon significantly increased the NH(3) adsorption capacity (10% RH); resultant adsorption capacity, q (mg/g) increased by approximately 2, 6, and 10 times for palm oil char, peanut hull char (pyrolysis only), and activated carbon, respectively. However, water vapor (73% RH at 23 degrees C) significantly reduced NH(3) adsorption capacity in the steam and ozone treated biomass, yet had no effect on the palm shell char generated at 500 degrees C. These results indicate the feasibility of using a low temperature (and thus low energy input) pyrolysis and activation process for the generation of NH(3) adsorbents from biomass residuals.

The Long-Term Study of Some mechanical and Chemical Properties of Polymer Modified Cement Waste Forms

International Nuclear Information System (INIS)

Shatta, H.A.; Eskander, S.B.

2002-01-01

The present work is a new experimental trend to study the long-term durability of polymer/cement/borate waste forms in storage and disposal sites during the long period of time. The data obtained indicate that all the samples of polymer modified cement waste forms immersed in both distilled and ground water (for more than 2700 days) show a slight increase in the compressive strength values. The chemical stability of the immobilized borate waste forms in distilled and ground water was studied. The cumulative leach fraction in percentage, of Cs-137 isotope from the final solidified waste forms in case of using ground water was lower than that in distilled water for all samples used and the presence of polymer lowered the percent release of radioactive Cs-137 isotope in all samples studied . The leach coefficients (Lc) and the leach indices (Li) of radioactive cesium-137 isotope for cement borate and polymer modified cement waste forms were also calculated. It was found that the leach indices values greater than 6

Iron-catalyzed gasification of char in CO/sub 2/

Energy Technology Data Exchange (ETDEWEB)

Furimsky, E.; Sears, P.; Suzuki, T.

Gasification of Fe-loaded char was carried out at 750 and 950 C by using media containing 25, 50, and 100 vol % of CO/sub 2/. Moessbauer spectroscopy was used to determine the forms of Fe species present before and at the end of gasification. At 750 C the reduction of magnetite by carbon was observed to be a rate-determining step. At 950 C the gasification may be governed by a combination of mass-transfer effects and a loss of active Fe. At 950 C both magnetite and wustite were present. The amount of the latter increased with decreasing CO/sub 2/ concentration in the gasification medium. 23 refs., 6 figs., 4 tabs.

Characterization, leachability and valorization through combustion of residual chars from gasification of coals with pine.

Science.gov (United States)

Galhetas, Margarida; Lopes, Helena; Freire, Márcia; Abelha, Pedro; Pinto, Filomena; Gulyurtlu, Ibrahim

2012-04-01

This paper presents the study of the combustion of char residues produced during co-gasification of coal with pine with the aim of characterizing them for their potential use for energy. These residues are generally rich in carbon with the presence of other elements, with particular concern for heavy metals and pollutant precursors, depending on the original fuel used. The evaluation of environmental toxicity of the char residues was performed through application of different leaching tests (EN12457-2, US EPA-1311 TCLP and EA NEN 7371:2004). The results showed that the residues present quite low toxicity for some of pollutants. However, depending on the fuel used, possible presence of other pollutants may bring environmental risks. The utilization of these char residues for energy was in this study evaluated, by burning them as a first step pre-treatment prior to landfilling. The thermo-gravimetric analysis and ash fusibility studies revealed an adequate thermochemical behavior, without presenting any major operational risks. Fluidized bed combustion was applied to char residues. Above 700°C, very high carbon conversion ratios were obtained and it seemed that the thermal oxidation of char residues was easier than that of the coals. It was found that the char tendency for releasing SO(2) during its oxidation was lower than for the parent coal, while for NO(X) emissions, the trend was observed to increase NO(X) formation. However, for both pollutants the same control techniques might be applied during char combustion, as for coal. Furthermore, the leachability of ashes resulting from the combustion of char residues appeared to be lower than those produced from direct coal combustion. Copyright © 2011 Elsevier Ltd. All rights reserved.

Fire and heat resistant laminating resins based on maleimido substituted aromatic cyclotriphosphazene polymer

Science.gov (United States)

Kumar, Devendra (Inventor); Fohlen, George M. (Inventor); Parker, John A. (Inventor)

1987-01-01

4-Aminophenoxy cyclotriphosphazenes are reacted with maleic anhydride to produce maleamic acids which are converted to the maleimides. The maleimides are polymerized. By selection of starting materials (e.g., hexakis amino or trisaminophenoxy trisphenoxy cyclotriphosphazenes), selection of molar proportions of reactants, use of mixtures of anhydrides and use of dianhydrides as bridging groups a variety of maleimides and polymers are produced. The polymers have high limiting oxygen indices, high char yields and other useful heat and fire resistant properties making them useful as, for example, impregnants of fabrics.

Comparison of high temperature chars of wheat straw and rice husk with respect to chemistry, morphology and reactivity

DEFF Research Database (Denmark)

Trubetskaya, Anna; Jensen, Peter Arendt; Jensen, Anker Degn

2016-01-01

Fast pyrolysis of wheat straw and rice husk was carried out in an entrained flow reactor at hightemperatures(1000e1500) C. The collected char was analyzed using X-ray diffractometry, N2-adsorption,scanning electron microscopy, particle size analysis with CAMSIZER XT, 29Si and 13C solid-statenucle......), which led to the formation of a glassy char shell, resulting in a preserved particlesize and shape of chars. The high alkali content in the wheat straw resulted in higher char reactivity,whereas the lower silicon content caused variations in the char shape from cylindrical to near...

Modeling char conversion under suspension fired conditions in O2/N2 and O2/CO2 atmospheres

DEFF Research Database (Denmark)

Brix, Jacob; Jensen, Peter Arendt; Jensen, Anker Degn

2011-01-01

The aim of this investigation has been to model combustion under suspension fired conditions in O2/N2 and O2/CO2 mixtures. Experiments used for model validation have been carried out in an electrically heated Entrained Flow Reactor (EFR) at temperatures between 1173 K and 1673 K with inlet O2...... concentrations between 5 and 28 vol.%. The COal COmbustion MOdel, COCOMO, includes the three char morphologies: cenospheric char, network char and dense char each divided between six discrete particle sizes. Both combustion and gasification with CO2 are accounted for and reaction rates include thermal char...

Relation between the petrographic composition of coal and the morphology of pyrolysis char produced in fluidized bed

Energy Technology Data Exchange (ETDEWEB)

B. Valentim; M.J. Lemos de Sousa; P. Abelha; D. Boavida; I. Gulyurtlu [Centro de Geologia da Universidade do Porto, Porto (Portugal)

2004-06-01

Several previous studies have already established, for pulverized coal combustion conditions, global correlations between petrographic composition of the coal and those of char produced from the same coal. However, for fluidized bed combustion, there has not been much new work since the eighties. The results presented in this paper include the petrographic characterization of seven different coals from several origins and also of their respective chars produced at 700, 800, 900, and 1000{sup o}C in a laboratory fluidized bed reactor. The results show a marked predominance of tenuispheres as the trial temperatures increase. While vitrinite-rich coals essentially produced highly porous chars, the inertinite-rich coals produced large amounts of medium- and low-porous chars. Semi-anthracite vitrinite produced high-porous chars and thermal affected coal particles originated low-porous and angular char morphotypes. The analysis of the data obtained revealed that vitrinite + liptinite related well with the high-porous char (sum of cenospheres and tenuinetworks), classified as Group 1. The same trend, but with a weaker relation, was also observed between vitrinite and liptinite rich microlithotypes and Group 1. 32 refs., 17 refs., 3 tabs.

CO2 gasification of char from lignocellulosic garden waste: Experimental and kinetic study.

Science.gov (United States)

Gupta, Ankita; Thengane, Sonal K; Mahajani, Sanjay

2018-04-25

In this study, the dry leaves litter from jackfruit, raintree, mango and eucalyptus trees, lignin, and cellulose were characterized, pyrolysed, and evaluated for their char reactivity towards CO 2 gasification using TGA. The differences in char reactivity were attributed to the difference in char morphology and the varying inorganic contents. The mineral analysis of biomass ash showed the presence of alkali minerals some of which could act as catalysts. The adverse effect of high silica content was also evident through the experimental results. The kinetic parameters for gasification reaction were determined using three different reaction models. A modified random pore model was investigated to account for the influence of inorganic content. The effect of external catalyst on CO 2 gasification was also studied by adding potassium carbonate to biomass char and pellets. The results obtained from this study can be conveniently used in the design of a gasifier for lignocellulosic garden waste. Copyright © 2018 Elsevier Ltd. All rights reserved.

Single-Point Incremental Forming of Two Biocompatible Polymers: An Insight into Their Thermal and Structural Properties

Directory of Open Access Journals (Sweden)

Luis Marcelo Lozano-Sánchez

2018-04-01

Full Text Available Sheets of polycaprolactone (PCL and ultra-high molecular weight polyethylene (UHMWPE were fabricated and shaped by the Single-Point Incremental Forming process (SPIF. The performance of these biocompatible polymers in SPIF was assessed through the variation of four main parameters: the diameter of the forming tool, the spindle speed, the feed rate, and the step size based on a Box–Behnken design of experiments of four variables and three levels. The design of experiments allowed us to identify the parameters that most affect the forming of PCL and UHMWPE. The study was completed by means of a deep characterization of the thermal and structural properties of both polymers. These properties were correlated to the performance of the polymers observed in SPIF, and it was found that the polymer chains are oriented as a consequence of the SPIF processing. Moreover, by X-ray diffraction it was proved that polymer chains behave differently on each surface of the fabricated parts, since the chains on the surface in contact with the forming tool are oriented horizontally, while on the opposite surface they are oriented in the vertical direction. The unit cell of UHMWPE is distorted, passing from an orthorhombic cell to a monoclinic due to the slippage between crystallites. This slippage between crystallites was observed in both PCL and UHMWPE, and was identified as an alpha star thermal transition located in the rubbery region between the glass transition and the melting point of each polymer.

Suprasubduction volcanic rocks of the Char ophiolite belt, East Kazakhstan: new geochemical and first geochronological data

Science.gov (United States)

Safonova, Inna; Simonov, Vladimir; Seltmann, Reimar; Yamamoto, Shinji; Xiao, Wenjiao

2016-04-01

The Char ophiolite belt is located in the western Central Asian Orogenic Belt, a world largest accretionary orogen, which has evolved during more than 800 Ma. The Char belt formed during Kazakhstan - Siberia collision. It has been known for hosting fragments of Late Devonian-Early Carboniferous oceanic crust, MORB, OPB and OIB, of the Paleo-Asian Ocean (Safonova et al., 2012). The Char is surrounded by two Paleozoic island-arc terranes: Zharma-Saur in the west and Rudny Altai in the east, however, until recent times, no island-arc units have been found within it. We were the first to find island-arc units as tectonic sheets occurring adjacent to those consisting of oceanic rocks. In places, island-arc andesites cut oceanic basalts. The Char volcanic and subvolcanic rocks of a probable suprasubduction origin are basalt, microgabbro, dolerite, andesite, tonalite and dacite. The mafic to andesitic volcanics possessing low TiO2 (0.85 wt.%av.) and show MgO vs. major elements crystallization trends suggesting two magma series: tholeiitic and calc-alkaline. The tholeiitic varieties are less enriched in incompatible elements then the calc-alkaline ones. Two samples are high-Mg and low-Ti andesibasalts similar to boninites. The rocks possess moderately LREE enriched rare-earth element patterns and are characterized by negative Nb anomalies present on the multi-element spectra (Nb/Lapm = 0.14-0.47; Nb/Thpm = 0.7-1.6).The distribution of rare-earth elements (La/Smn = 0.8-2.3, Gd/Ybn = 0.7-1.9) and the results of geochemical modeling in the Nb-Yb system suggest high degrees of melting of a depleted harzburgite-bearing mantle source at spinel facies depths. Fractional crystallization of clinopyroxene, plagioclase and opaque minerals also affected the final composition of the volcanic rocks. Clinopyroxene monomineral thermometry indicates crystallization of melts at 1020-1180°C. Melt inclusion composition based numerical calculations show that primary melts were derived at 1350

Mechanism and Thermochemistry of Coal Char Oxidation and Desorption of Surface Oxides

DEFF Research Database (Denmark)

Levi, Gianluca; Causà, Mauro; Lacovig, Paolo

2017-01-01

The present study investigates the coal char combustion by a combination of thermochemical and X-ray photoemission spectroscopy (XPS) analyses. Thermoanalytical methods (differential thermogravimetry, differential scanning calorimetry, and temperature-programmed desorption) are used to identify...... the key reactive steps that occur upon oxidation and heating of coal char (chemisorption, structural rearrangement and switchover of surface oxides, and desorption) and their energetics. XPS is used to reveal the chemical nature of the surface oxides that populate the char surface and to monitor...... functionalities prevail. The rearrangement of epoxy during preoxidation goes together with activation of the more stable and less reactive carbon sites. Results are in good agreement with semi-lumped kinetic models of carbon oxidation, which include (1) formation of "metastable" surface oxides, (2) complex...

Thermogravimetric study on the influence of structural, textural and chemical properties of biomass chars on CO2 gasification reactivity

International Nuclear Information System (INIS)

Bouraoui, Zeineb; Jeguirim, Mejdi; Guizani, Chamseddine; Limousy, Lionel; Dupont, Capucine; Gadiou, Roger

2015-01-01

The present investigation aims to examine the influence of textural, structural and chemical properties of biomass chars on the CO 2 gasification rate. Various lignocellulosic biomass chars were prepared under the same conditions. Different analytical techniques were used to determine the char properties such as Scanning Electronic Microscopy, nitrogen adsorption manometry, Raman spectroscopy and X Ray Fluorescence. Gasification tests were carried out in a thermobalance under 20% CO 2 in nitrogen at 800 °C. Significant differences of the total average reactivity were observed with a factor of 2 between the prepared chars. Moreover, different behaviors of gasification rate profiles versus conversion were obtained. This difference of behavior appeared to be correlated with the biomass char properties. Hence, up to 70% of conversion, the gasification rate was shown to depend on the char external surface and the potassium content. At higher conversion ratio, a satisfactory correlation between the Catalytic Index and the average gasification rate was identified. The results highlight the importance of knowing both textural and structural properties and mineral contents of biomass chars to predict fuel reactivity during CO 2 gasification processes. Such behavior prediction is highly important in the gasifiers design for char conversion. - Highlights: • CO 2 gasification reactivity of various lignocellulosic chars were examined. • Chars properties affect strongly samples gasification behavior. • Initial gasification rate is affected by external surface, K content and D3/G ratio. • Gasification rate behavior depends on the Alkali index at high conversion

Effect of low-molecular-weight beta-cyclodextrin polymer on release of drugs from mucoadhesive buccal film dosage forms.

Science.gov (United States)

Arakawa, Yotaro; Kawakami, Shigeru; Yamashita, Fumiyoshi; Hashida, Mitsuru

2005-09-01

We investigated the effect of low-molecular-weight beta-cyclodextrin (beta-CyD) polymer on in vitro release of two drugs with different lipophilicities (i.e., lidocaine and ketoprofen) from mucoadhesive buccal film dosage forms. When beta-CyD polymer was added to hydroxypropylcellulose (HPC) or polyvinylalcohol (PVA) film dosage forms, the release of lidocaine into artificial saliva (pH 5.7) was reduced by 40% of the control. In contrast, the release of ketoprofen from the polymer film was enhanced by addition of beta-CyD polymer to the vehicle. When lidocaine and ketoprofen was incubated with beta-CyD polymer in the artificial saliva, concentration of free lidocaine molecules decreased in a beta-CyD polymer concentration-dependent manner. The association constant with beta-CyD polymer was 6.9+/-0.6 and 520+/-90 M(-1) for lidocaine and ketoprofen, respectively. Retarded release of the hydrophilic lidocaine by beta-CyD polymer might be due to the decrease in thermodynamic activity by inclusion complex formation, whereas enhanced release of the lipophilic ketoprofen by the beta-CyD polymer might be due to prevention of recrystallization occurring after contacting the film with aqueous solution. Thus, effects of low-molecular-weight beta-CyD polymer to the drug release rate from film dosage forms would vary according to the strength of interaction with and the solubility of active ingredient.

Chars from gasification of coal and pine activated with K2CO3: acetaminophen and caffeine adsorption from aqueous solutions.

Science.gov (United States)

Galhetas, Margarida; Mestre, Ana S; Pinto, Moisés L; Gulyurtlu, Ibrahim; Lopes, Helena; Carvalho, Ana P

2014-11-01

The high carbon contents and low toxicity levels of chars from coal and pine gasification provide an incentive to consider their use as precursors of porous carbons obtained by chemical activation with K2CO3. Given the chars characteristics, previous demineralization and thermal treatments were made, but no improvement on the solids properties was observed. The highest porosity development was obtained with the biomass derived char (Pi). This char sample produced porous materials with preparation yields near 50% along with high porosity development (ABET≈1500m(2)g(-1)). For calcinations at 800°C, the control of the experimental conditions allowed the preparation of samples with a micropore system formed almost exclusively by larger micropores. A mesopore network was developed only for samples calcined at 900°C. Kinetic and equilibrium acetaminophen and caffeine adsorption data, showed that the processes obey to a pseudo-second order kinetic equation and to the Langmuir model, respectively. The results of sample Pi/1:3/800/2 outperformed those of the commercial carbons. Acetaminophen adsorption process was ruled by the micropore size distribution of the carbons. The caffeine monolayer capacities suggest a very efficient packing of this molecule in samples presenting monomodal micropore size distribution. The surface chemistry seems to be the determinant factor that controls the affinity of caffeine towards the carbons. Copyright © 2014 Elsevier Inc. All rights reserved.

Removal of copper by oxygenated pyrolytic tire char: kinetics and mechanistic insights.

Science.gov (United States)

Quek, Augustine; Balasubramanian, Rajashekhar

2011-04-01

The kinetics of copper ion (Cu(II)) removal from aqueous solution by pyrolytic tire char was modeled using five different conventional models. A modification to these models was also developed through a modified equation that accounts for precipitation. Conventional first- and second-order reaction models did not fit the copper sorption kinetics well, indicating a lack of simple rate-order dependency on solute concentration. Instead, a reversible first-order rate reaction showed the best fit to the data, indicating a dependence on surface functional groups. Due to the varying solution pH during the sorption process, modified external and internal mass transfer models were employed. Results showed that the sorption of copper onto oxygenated chars was limited by external mass transfer and internal resistance with and without the modification. However, the modification of the sorption process produced very different results for unoxygenated chars, which showed neither internal nor external limitation to sorption. Instead, its slow sorption rate indicates a lack of surface functional groups. The sorption of Cu(II) by oxygenated and unoxygenated chars was also found to occur via three and two distinct stages, respectively. Copyright © 2010 Elsevier Inc. All rights reserved.

CFD Simulation of Entrained Flow Gasification With Improved Devolatilization and Char Consumption Submodels

KAUST Repository

Kumar, Mayank; Zhang, Cheng; Monaghan, Rory F. D.; Singer, Simcha L.; Ghoniem, Ahmed F.

2009-01-01

In this work, we use a CFD package to model the operation of a coal gasifier with the objective of assessing the impact of devolatilization and char consumption models on the accuracy of the results. Devolatilization is modeled using the Chemical Percolation Devolitilization (CPD) model. The traditional CPD models predict the rate and the amount of volatiles released but not their species composition. We show that the knowledge of devolatilization rates is not sufficient for the accurate prediction of char consumption and a quantitative description of the devolatilization products, including the chemical composition of the tar, is needed. We incorporate experimental data on devolatilization products combined with modeling of the tar composition and reactions to improve the prediction of syngas compositions and carbon conversion. We also apply the shrinking core model and the random pore model to describe char consumption in the CFD simulations. Analysis of the results indicates distinct regimes of kinetic and diffusion control depending on the particle radius and injection conditions for both char oxidation and gasification reactions. The random pore model with Langmuir-Hinshelwood reaction kinetics are found to be better at predicting carbon conversion and exit syngas composition than the shrinking core model with Arrhenius kinetics. In addition, we gain qualitative and quantitative insights into the impact of the ash layer surrounding the char particle on the reaction rate. Copyright © 2010 by ASME.

Study of bio-oil and bio-char production from algae by slow pyrolysis

International Nuclear Information System (INIS)

Chaiwong, K.; Kiatsiriroat, T.; Vorayos, N.; Thararax, C.

2013-01-01

This study examined bio-oil and bio-char fuel produced from Spirulina Sp. by slow pyrolysis. A thermogravimetric analyser (TGA) was used to investigate the pyrolytic characteristics and essential components of algae. It was found that the temperature for the maximum degradation, 322 °C, is lower than that of other biomass. With our fixed-bed reactor, 125 g of dried Spirulina Sp. algae was fed under a nitrogen atmosphere until the temperature reached a set temperature between 450 and 600 °C. It was found that the suitable temperature to obtain bio-char and bio-oil were at approximately 500 and 550 °C respectively. The bio-oil components were identified by a gas chromatography/mass spectrometry (GC–MS). The saturated functional carbon of the bio-oil was in a range of heavy naphtha, kerosene and diesel oil. The energy consumption ratio (ECR) of bio-oil and bio-char was calculated, and the net energy output was positive. The ECR had an average value of 0.49. -- Highlights: •Bio-oil and bio-char fuel produced from Spirulina Sp. by slow pyrolysis. •Suitable temperature to obtained bio-oil and bio-char were at about 550 and 500 °C. •Saturated functional carbon of bio-oil was heavy naphtha, kerosene, diesel oil. •ECR had an average value of 0.49

Novel intrinsic-based submodel for char particle gasification in entrained-flow gasifiers: Model development, validation and illustration

International Nuclear Information System (INIS)

Schulze, S.; Richter, A.; Vascellari, M.; Gupta, A.; Meyer, B.; Nikrityuk, P.A.

2016-01-01

Highlights: • Model resolving intra-particle species transport for char conversion was formulated. • TGA experiments of char particle conversion in gas flow were conducted. • The experimental results for char conversion validated the model. • CFD simulations of endothermic reactor with developed model were carried out. - Abstract: The final carbon conversion rate is of critical importance in the efficiency of gasifiers. Therefore, comprehensive modeling of char particle conversion is of primary interest for designing new gasifiers. This work presents a novel intrinsic-based submodel for the gasification of a char particle moving in a hot flue gas environment considering CO 2 and H 2 O as inlet species. The first part of the manuscript describes the model and its derivation. Validations against experiments carried out in this work for German lignite char are reported in the second part. The comparison between submodel predictions and experimental data shows good agreement. The importance of char porosity change during gasification is demonstrated. The third part presents the results of CFD simulations using the new submodel and a surface-based submodel for a generic endothermic gasifier. The focus of CFD simulations is to demonstrate the crucial role of intrinsic based heterogeneous reactions in the adequate prediction of carbon conversion rates.

Removal of hexavalent Cr by coconut coir and derived chars--the effect of surface functionality.

Science.gov (United States)

Shen, Ying-Shuian; Wang, Shan-Li; Tzou, Yu-Min; Yan, Ya-Yi; Kuan, Wen-Hui

2012-01-01

The Cr(VI) removal by coconut coir (CC) and chars obtained at various pyrolysis temperatures were evaluated. Increasing the pyrolysis temperature resulted in an increased surface area of the chars, while the corresponding content of oxygen-containing functional groups of the chars decreased. The Cr(VI) removal by CC and CC-derived chars was primarily attributed to the reduction of Cr(VI) to Cr(III) by the materials and the extent and rate of the Cr(VI) reduction were determined by the oxygen-containing functional groups in the materials. The contribution of pure Cr(VI) adsorption to the overall Cr(VI) removal became relatively significant for the chars obtained at higher temperatures. Accordingly, to develop a cost-effective method for removing Cr(VI) from water, the original CC is more advantageous than the carbonaceous counterparts because no pyrolysis is required for the application and CC has a higher content of functional groups for reducing Cr(VI) to less toxic Cr(III). Copyright © 2011 Elsevier Ltd. All rights reserved.

The role of char and tar in determining the gas-phase partitioning of nitrogen during biomass gasification

International Nuclear Information System (INIS)

Broer, Karl M.; Brown, Robert C.

2015-01-01

Highlights: • Switchgrass was gasified at an equivalence ratio of zero and 650–850 °C. • Short residence times were employed to minimize secondary reactions. • Char- and tar-bound nitrogen, NH_3, HCN, and N_2 were all significant products. • Increasing temperature leads to increased release of gaseous nitrogen compounds. • Kinetic models of gasification should include nitrogen release from char and tar. - Abstract: Gasification is an attractive option for converting biomass into fuels and chemicals. Most biomass contains significant amounts of fuel-bound nitrogen (FBN), which partially converts into ammonia (NH_3) and hydrogen cyanide (HCN) during gasification. These nitrogen compounds are problematic as they can lead to NO_X emissions or catalyst poisoning in downstream applications of syngas. FBN can convert to other products as well, including diatomic nitrogen (N_2), char-bound nitrogen (char-N), and tar-bound nitrogen (tar-N). Efforts to predict concentrations of NH_3 and HCN have been hindered by a lack of accurate, comprehensive measurements of nitrogen partitioning among gasification products. The present study gasified switchgrass under allothermal, short residence time conditions and measured NH_3, HCN, char-N, and tar-N as a function of temperature in the range of 650–850 °C with diatomic nitrogen determined by difference. It was found that a major portion of FBN was retained in the char and tar products. As temperature was increased, char and tar were consumed, releasing nitrogen as gaseous NH_3 and HCN. This increase in undesirable nitrogen compounds is contrary to the predictions of most gasification models, which overlook the presence of significant nitrogen in char and tar even if they include tar cracking and char gasification reactions. The results of this study demonstrate that gas-phase reactions alone are not sufficient to predict the fate of nitrogen during gasification. In order for modeling efforts to obtain more accurate

Synergistic Effect of Co-utilization of Coal and Biomass Char: An Overview

Science.gov (United States)

Paiman, M. E. S.; Hamzah, N. S.; Idris, S. S.; Rahman, N. A.; Ismail, K.

2018-05-01

Global concerns on impact of greenhouse gases emission, mostly released from coal-fired power plant, and the depletion of fossil fuel particularly coal, has led the production of electricity from alternatives resources such as co-utilization technologies. Previous studies proved that the co-utilization of coal and biomass/biomass chars has significantly reduced the emission of greenhouse gases either during the pyrolysis, combustion or gasification process in laboratories, pilots as well as in the industrial scales. Interestingly, most of the studies reported the presence of synergistic effect during the co-utilization processes particularly between coal and biomass char while some are not. Biomass chars were found to have porous and highly disorder carbon structure and belong to the class of most reactive carbon material, resulting to be more reactive than those hard coal and lignite. Up to date, microwave assisted pyrolysis is one of the best and latest techniques employed to produce better quality of biomass chars and it is also reduce the processing cost. Lot of works has been done regarding on the existence of synergistic effects during its co-utilization. However, the knowledge is limited to thermal and product characteristics so far. Even so, the specific reasons behind its existence are yet to understand well. Therefore, in this paper, the emphasis will be given on the synergistic effects on emission characteristics of co-utilization of coal and biomass chars so that it can be apply in energy-based industries to help in reduction of the greenhouse gases emission.

Effect of cation exchange on the subsequent reactivity of lignite chars to steam. [108 references

Energy Technology Data Exchange (ETDEWEB)

Hippo, E. J.; Walker, Jr., P. L.

1977-03-01

The purpose of this investigation is to determine the role which cations in coal play in the subsequent reactivity of chars. It is hoped that this investigation will aid in an understanding of the catalytic nature of inorganic constituents in coal during its gasification. It was found that increased heat treatment temperature decreased reactivity. The decrease in reactivity was shown to be due, at least in part, to the changes in the nature of the cation with increased heat treatment temperature. Reactivity was found to be a linear function of the amount of Ca(++) exchange on the demineralized coal. The constant utilization factor over the wide range of loadings employed indicated that below 800/sup 0/C the calcium did not markedly sinter. Potassium, sodium, and calcium-containing chars were found to be much more reactive than the iron and magnesium-containing chars. However, the iron and magnesium containing chars were more reactive than chars produced from the demineralized coal. The iron char was highly active at first but the iron phase was quickly oxidized to a comparatively unreactive ..gamma..Fe/sub 2/O/sub 3/-Fe/sub 3/O/sub 4/ phase. The state of magnesium was found to be MgO. Sodium and calcium were equally active as catalysts but not as active as potassium.

Porous structure and morphology of granular chars from flash and conventional pyrolysis of grape seeds

International Nuclear Information System (INIS)

Jimenez-Cordero, Diana; Heras, Francisco; Alonso-Morales, Noelia; Gilarranz, Miguel A.; Rodriguez, Juan J.

2013-01-01

This work studies the influence of the operating conditions used in the pyrolysis of grape seeds on the morphology and textural properties of the chars resulting. Flash and conventional (283 K min −1 heating rate) pyrolysis have been used within a wide range of temperature (300–1000 °C). The effect of a pretreatment for oil extraction has also been studied. The porous structure of the chars was characterized by adsorption of N 2 at 77 K, Ar at 77 K and 87 K, and CO 2 at 273 K and mercury intrusion porosimetry. The morphology was analyzed by scanning electron microscopy. All the materials prepared revealed an essentially microporous structure, with a poor or even negligible contribution of mesopores. Increasing pyrolysis temperature led to higher specific surface areas and lower pore size. The highest specific surface area values occurred within 700–800 °C, reaching up to 500 m 2 g −1 with pore sizes in the 0.4–1.1 nm range. No significant morphological changes were observed upon carbonization so that the resulting chars were granular materials of similar size than the starting grape seeds. The hollow core structure of the chars, with most of the material allocated at the periphery of the granules can help to overcome the mass transfer limitations of most common (solid or massive) granular activated carbons. The chars showed a good mechanical strength during attrition tests. These chars can be potential candidates for the preparation of granular carbons molecular sieve or activated carbons raw materials. -- Highlights: •We use a raw material that has a very low price and a high availability. •Not very much attention has been paid to this waste for carbonaceous materials preparation. •The chars obtained have high specific surface area that is an interesting starting point for later activation processes. •The chars show a micro-macro porous bimodal distribution. •Pyrolysis does not affect to morphology or initial seed, leading a carbonized

iQOS: evidence of pyrolysis and release of a toxicant from plastic.

Science.gov (United States)

Davis, Barbara; Williams, Monique; Talbot, Prue

2018-03-13

To evaluate performance of the I quit original smoking (iQOS) heat-not-burn system as a function of cleaning and puffing topography, investigate the validity of manufacturer's claims that this device does not burn tobacco and determine if the polymer-film filter is potentially harmful. iQOS performance was evaluated using five running conditions incorporating two different cleaning protocols. Heatsticks were visually and stereomicroscopically inspected preuse and postuse to determine the extent of tobacco plug charring (from pyrolysis) and polymer-film filter melting, and to elucidate the effects of cleaning on charring. Gas chromatography-mass spectrometry headspace analysis was conducted on unused polymer-film filters to determine if potentially toxic chemicals are emitted from the filter during heating. For all testing protocols, pressure drop decreased as puff number increased. Changes in testing protocols did not affect aerosol density. Charring due to pyrolysis (a form of organic matter thermochemical decomposition) was observed in the tobacco plug after use. When the manufacturer's cleaning instructions were followed, both charring of the tobacco plug and melting of the polymer-film filter increased. Headspace analysis of the polymer-film filter revealed the release of formaldehyde cyanohydrin at 90°C, which is well below the maximum temperature reached during normal usage. Device usage limitations may contribute to decreases in interpuff intervals, potentially increasing user's intake of nicotine and other harmful chemicals. This study found that the tobacco plug does char and that charring increases when the device is not cleaned between heatsticks. Release of formaldehyde cyanohydrin is a concern as it is highly toxic at very low concentrations. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Reactivity of coal chars prepared in a fluidised bed reactor at different burn-off degrees

Energy Technology Data Exchange (ETDEWEB)

Moreno, A.H.; Arenillas, A.; Rubiera, F.; Fuente, E.; Pis, J.J. [Inst. Nacional del Carbon, Oviedo (Spain)

1997-12-31

The main goal of this work has been to study the effect of the textural properties of coal chars, obtained from partially burned coal, on their reactivity to oxygen. A low volatile bituminous coal was used to prepare chars, with different levels of burn-off, in a bench-scale fluidised bed reactor. Textural characterisation of the samples was accomplished by measuring true (helium) and apparent (mercury) densities, and mercury porosimetry. An increase in the burn-off degree gave rise to a densification of the chars. Porosity development greatly changed during progressive burning of the samples. DTG burning profiles and isothermal gasification were utilised to estimate the reactivities of the precursor coal and its partially burned chars. Reactivity reached a maximum value at an intermediate burn-off and strongly decreased at higher burn-off degrees. (orig.)

Modeling and evaluation of chromium remediation from water using low cost bio-char, a green adsorbent

International Nuclear Information System (INIS)

Mohan, Dinesh; Rajput, Shalini; Singh, Vinod K.; Steele, Philip H.; Pittman, Charles U.

2011-01-01

Oak wood and oak bark chars were obtained from fast pyrolysis in an auger reactor at 400-450 deg. C. These chars were characterized and utilized for Cr(VI) remediation from water. Batch sorption studies were performed at different temperatures, pH values and solid to liquid ratios. Maximum chromium was removed at pH 2.0. A kinetic study yielded an optimum equilibrium time of 48 h with an adsorbent dose of 10 g/L. Sorption studies were conducted over a concentration range of 1-100 mg/L. Cr(VI) removal increased with an increase in temperature (Q Oakwood o : 25 deg. C = 3.03 mg/g; 35 deg. C = 4.08 mg/g; 45 deg. C = 4.93 mg/g and Q Oakbark o : 25 deg. C = 4.62 mg/g; 35 deg. C = 7.43 mg/g; 45 deg. C = 7.51 mg/g). More chromium was removed with oak bark than oak wood. The char performances were evaluated using the Freundlich, Langmuir, Redlich-Peterson, Toth, Radke and Sips adsorption isotherm models. The Sips adsorption isotherm model best fits the experimental data [high regression (R 2 ) coefficients]. The overall kinetic data was satisfactorily explained by a pseudo second order rate expression. Water penetrated into the char walls exposing Cr(VI) to additional adsorption sites that were not on the surfaces of dry char pores. It is remarkable that oak chars (S BET : 1-3 m 2 g -1 ) can remove similar amounts of Cr(VI) as activated carbon (S BET : ∼1000 m 2 g -1 ). Thus, byproduct chars from bio-oil production might be used as inexpensive adsorbents for water purification. Char samples were successfully used for chromium remediation from contaminated surface water with dissolved interfering ions.

Modeling and evaluation of chromium remediation from water using low cost bio-char, a green adsorbent.

Science.gov (United States)

Mohan, Dinesh; Rajput, Shalini; Singh, Vinod K; Steele, Philip H; Pittman, Charles U

2011-04-15

Oak wood and oak bark chars were obtained from fast pyrolysis in an auger reactor at 400-450 °C. These chars were characterized and utilized for Cr(VI) remediation from water. Batch sorption studies were performed at different temperatures, pH values and solid to liquid ratios. Maximum chromium was removed at pH 2.0. A kinetic study yielded an optimum equilibrium time of 48 h with an adsorbent dose of 10 g/L. Sorption studies were conducted over a concentration range of 1-100mg/L. Cr(VI) removal increased with an increase in temperature (Q(Oak wood)(°): 25 °C = 3.03 mg/g; 35 °C = 4.08 mg/g; 45 °C = 4.93 mg/g and Q(Oakbark)(°): 25 °C = 4.62 mg/g; 35 °C = 7.43 mg/g; 45 °C = 7.51 mg/g). More chromium was removed with oak bark than oak wood. The char performances were evaluated using the Freundlich, Langmuir, Redlich-Peterson, Toth, Radke and Sips adsorption isotherm models. The Sips adsorption isotherm model best fits the experimental data [high regression (R(2)) coefficients]. The overall kinetic data was satisfactorily explained by a pseudo second order rate expression. Water penetrated into the char walls exposing Cr(VI) to additional adsorption sites that were not on the surfaces of dry char pores. It is remarkable that oak chars (S(BET): 1-3m(2)g(-1)) can remove similar amounts of Cr(VI) as activated carbon (S(BET): ∼ 1000 m(2)g(-1)). Thus, byproduct chars from bio-oil production might be used as inexpensive adsorbents for water purification. Char samples were successfully used for chromium remediation from contaminated surface water with dissolved interfering ions. Copyright © 2011 Elsevier B.V. All rights reserved.

Micro-PIXE studies of char populations in northern Canada

International Nuclear Information System (INIS)

Campbell, J.L.; Babaluk, J.A.; Halden, N.M.; Kristofferson, A.H.; Maxwell, J.A.; Mejia, S.R.; Reist, J.D.; Teesdale, W.J.

1999-01-01

Micro-PIXE analysis of trace elements in otoliths has been used as the basis for several projects on char, a fish that is important for aboriginal subsistence fisheries in Arctic Canada. Life-history patterns were originally inferred from micro-PIXE line scans of Sr distribution. These were confirmed by superposition of Sr distribution patterns on optical images of otoliths of tag-recaptured fish. Char from various populations showed differentiation in otolith primordial Sr concentration; this enables us to differentiate biological stocks and, it is hoped, eventually to assign individuals from mixed-stock fisheries to their stock of origin. Zn oscillations also correlate with annular structure and provide additional temporally constrained information on fish habitat and behaviour

Characterization of a Neochlamydia-like Bacterium Associated with Epitheliocystis in Cultured Artic Char Salvelinus alpinus

Science.gov (United States)

Infections of branchial epithelium by intracellular gram-negative bacteria, termed epitheliocystis, have limited culture of Arctic char (Salvelinus alpinus). To characterize a bacterium associated with epitheliocystis in cultured char, gills were sampled for histopathologic examination, conventional...

Electron paramagnetic resonance and dynamic nuclear polarization of char suspensions: surface science and oximetry

DEFF Research Database (Denmark)

Clarkson, R B; Odintsov, B M; Ceroke, P J

1998-01-01

; they can be calibrated and used for oximetry. Biological stability and low toxicity make chars good sensors for in vivo measurements. Scalar and dipolar interactions of water protons at the surfaces of chars may be utilized to produce dynamic nuclear polarization (DNP) of the nuclear spin population...

Investigation of the structure of multiwall carbon nanotubes in polymer matrix

International Nuclear Information System (INIS)

Major, A Adamne; Belina, K

2013-01-01

In the last ten years carbon nanotube composites are in the focus of the researchers. Concentration series were prepared using carbon nanotube containing master blend by IDMX mixer. In the experiments polypropylene, polycarbonate and ABS polymers were used as matrix materials. The prepared materials were characterised by scanning electron microscopy. The carbon nanotubes can be seen on the fractured surfaces. We did not find any sign of agglomerates in the materials. The nanocomposites were investigated by LP-FTIR method. The specimens were irradiated with 1 W for 1 minute by CO 2 laser. The polymer matrix was burnt or charred by the CO 2 laser; the structure of the carbon nanotubes in the matrix was studied. The carbon nanotubes create a physical network in the polymers we used

Contributing variables for sustainable livelihood status of the char women in Bangladesh

Directory of Open Access Journals (Sweden)

S. Al-Amin

2012-03-01

Full Text Available The main purpose of the study was to determine the contribution of variables to the sustainable livelihood status of char women. The sustainable livelihood status of a char woman was measured by computing a “sustainable livelihood status score” which is considering six major aspects of her livelihoods: food security, ability to provide family education, health and sanitation, shelter and family assets, clothing condition and social upliftment. Data were collected from 200 randomly selected char women by using interview schedule in two Upazilla of Jamalpur district in Bangladesh during November 2006 to March 2007. More than two-fifths (67.5 per cent of the char women were found under “medium sustainable livelihood status” compared to more than one-fifth (20.5 per cent of them belongs to ‘low sustainable livelihood status’ and only 12 per cent to “high sustainable livelihood status”. Pearson correlation test depicted that out of 16 variables, 13 had significant positive relationships with the sustainable livelihood status. Results of stepwise multiple regression analysis revealed that five variables namely, annual income, agricultural knowledge, income generating activities, family education and organizational participation contributed significantly which combindly explained 76.3 per cent of total variation to the sustainable livelihood status. Path analysis indicated that these variables had both direct and indirect effects to the sustainable livelihood status. Women who had more annual income, better agricultural knowledge, participation in income generating activities, more family education and more organizational participation were found to better sustainable livelihood status in char area. Government or concern other authorities need to give attention to these variables for any sustainable livelihood upliftment programme.

Leaching of major and trace elements from paper-plastic gasification chars. An experimental and modelling study

Energy Technology Data Exchange (ETDEWEB)

Fuente-Cuesta, A.; Lopez-Anton, M.A.; Diaz-Somoano, M.; Martinez-Tarazona, M.R. [Instituto Nacional del Carbon CSIC, C/Francisco Pintado Fe No 26, 33011, Oviedo (Spain); Van Zomeren, A.; Cieplik, M. [Energy research Centre of the Netherlands ECN, Biomass, P.O. Box 1, 1755 ZG, Petten (Netherlands)

2013-01-15

The control of soluble metal species in the sub-product leachate generated in electricity production processes is of great concern from an environmental and health point of view. Unlike fly ash, the leaching behaviour of char materials has received little attention. Yet, these solids are captured together with fly ashes in the particle control devices of power plants and are emitted in the same way as by-products. The present study was carried out using two char samples: (1) a raw char and (2) the same type of char employed in a previous study so that it could serve as a sorbent for mercury species in gas phase. The char samples were by-products (residues) that had been generated during the gasification of plastic and paper waste. The leachates were analyzed for the following elements: Al, Ca, Si, Mg, Ba, Cu, Ni, Pb, Zn, Mo and Hg. In addition, geochemical modelling of the leaching test results was employed to identify the underlying chemical processes that led to the release of toxic elements. The results showed that at alkaline pH values, sorption on the solid surfaces of the char was negligible due to the inorganic complexation of cations in the solution. When the char was used as mercury sorbent slight changes occurred on the reactive surface resulting in the modification of the binding of some elements. As the pH increased, complexation with dissolved organic matter played a more important role in the case of some elements such as Cu because of the greater concentration of dissolved organic matter in solution.

Advances in CO_2 gasification reactivity of biomass char through utilization of radio frequency irradiation

International Nuclear Information System (INIS)

Lahijani, Pooya; Mohammadi, Maedeh; Zainal, Zainal Alimuddin; Mohamed, Abdul Rahman

2015-01-01

A straightforward and well-known reaction for CO_2 activation is the “Boudouard reaction”, wherein, CO_2 is reacted with carbon (char) to produce CO. In this study, a RF (radio frequency) heating system was developed to perform the Boudouard reaction by passing CO_2 through a packed bed of PNS (pistachio nut shell) char. High CO_2 conversion of 84% was achieved at 850 °C. When similar experiments were performed in thermal electric furnace, the conversion was only 38%. For further expanding the knowledge on RF-induced gasification, sodium (Na) was incorporated into char skeleton and gasified with CO_2 under RF irradiation. RF gasification of Na-catalyzed char pronouncedly improved in the reaction, where sustainable CO_2 conversion of 99% was attained at 850 °C. The predominance of RF over thermal heating was highly reflected in kinetic studies, where the activation energies of 26.7, 46.9 and 183.9 kJ/mol were obtained for catalytic and non-catalytic RF and thermal gasification, respectively. In RF gasification studies, it was attempted to improve the quality of mix gases, simulating air and steam gasification gas compositions, through the Boudouard reaction. The heating value of the gases simulating air and steam gasification improved from 6.4 to 8.0 MJ/m"3 and 7.6–10.4 MJ/m"3, respectively. - Highlights: • We study radio frequency-induced CO_2 gasification of pistachio nut shell char. • We achieve very high CO_2 conversion of 99% in RF gasification of Na-catalyzed char. • E_a of 47 and 184 kJ/mol obtained for RF-assisted and conventional CO_2 gasification. • Heating value of synthesis gas improved via RF-induced char-CO_2 gasification.

Effects of catalysts on combustion characteristics and kinetics of coal-char blends

Science.gov (United States)

Hu, Yingjie; Wang, Zhiqiang; Cheng, Xingxing; Liu, Ming; Ma, Chunyuan

2018-04-01

The effects of Fe2O3, CaO, and MnO2 on the combustion characteristics and kinetics of coal-char blends were investigated using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The results indicated that catalysts exhibited positive effects on the combustion characteristics of coal-char blends, especially in the initial period of coal-char blends combustion. With catalysts addition (mass 1.5%), it could improves volatile matter release, and reduces ignition point, promotes char to begin burning under lower temperature. The ignition index (C) was increased, respectively, by 27% for Fe2O3, 6% for CaO, 11.3% for MnO2, and the combustion characteristic index ( S ) was increased respectively, by 29% for Fe2O3, 5% for CaO, 8.3% for MnO2. In addition, two kinetic models (R2 and F1) were adopted to calculate the kinetic parameters in different stage of combustion processes. The results showed that with Fe2O3 or CaO addition, the activation energy at second stage decreases from 86.0 KJ/mol to 76.92 KJ/mol and 75.12 KJ/mol, respectively. There are no obvious decreases at the third stage of samples combustion process.

Improvement of biomass char-CO{sub 2} gasification reactivity using microwave irradiation and natural catalyst

Energy Technology Data Exchange (ETDEWEB)

Lahijani, Pooya, E-mail: pooya.lahijani@gmail.com [Biomass and Bioenergy Laboratory, School of Mechanical Engineering, Universiti Sains Malaysia, 14300 Nibong Tebal, Pulau Pinang (Malaysia); Mohammadi, Maedeh, E-mail: m.mohammadi@nit.ac.ir [Faculty of Chemical Engineering, Babol Noushirvani University of Technology, 47148 Babol (Iran, Islamic Republic of); Zainal, Zainal Alimuddin, E-mail: mezainal@eng.usm.my [Biomass and Bioenergy Laboratory, School of Mechanical Engineering, Universiti Sains Malaysia, 14300 Nibong Tebal, Pulau Pinang (Malaysia); Mohamed, Abdul Rahman, E-mail: chrahman@usm.my [Low Carbon Economy (LCE) Research Group, School of Chemical Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Pulau Pinang (Malaysia)

2015-03-20

Highlights: • We study microwave-induced gasification of EFB ash-loaded biomass char with CO{sub 2}. • Synergistic effect of microwave and catalyst resulted in CO{sub 2} conversion of 93%. • Gasification of pristine char using conventional heating gives CO{sub 2} conversion of 58%. • E{sub a} of 74 and 247 kJ/mol were obtained for microwave and conventional CO{sub 2} gasification. - Abstract: In char-CO{sub 2} gasification, the highly endothermic nature of the Boudouard reaction (CO{sub 2} (g) + C (s) ↔ 2CO (g)) dictates use of very high temperatures to shift the equilibrium towards CO production. In this study, such high temperature (750–900 °C) was provided by microwave irradiation. A microwave heating system was developed to perform the gasification tests by passing CO{sub 2} through a packed bed of oil palm shell (OPS) char. In order to speed up the microwave-induced CO{sub 2} gasification, ash of palm empty fruit bunch (EFB) was used as natural catalyst (rich in potassium) and incorporated into the skeleton of the OPS char. The synergistic effect of microwave and catalyst concluded to very encouraging results, where a CO{sub 2} conversion of 93% was achieved at 900 °C, within 60 min microwave gasification. In comparison, CO{sub 2} conversion in thermal gasification (conventional heating) of pristine OPS char was only 58% under the same operating condition.

The potential applications of using compost chars for removing the hydrophobic herbicide atrazine from solution.

Science.gov (United States)

Tsui, Lo; Roy, William R

2008-09-01

One commercial compost sample was pyrolyzed to produce chars as a sorbent for removing the herbicide atrazine from solution. The sorption behavior of compost-based char was compared with that of an activated carbon derived from corn stillage. When compost was pyrolyzed, the char yield was greater than 45% when heated under air, and 52% when heated under N(2). In contrast, when the corn stillage was pyrolyzed under N(2), the yield was only 22%. The N(2)-BET surface area of corn stillage activated carbon was 439 m(2)/g, which was much greater than the maximum compost char surface area of 72 m(2)/g. However, the sorption affinity of the compost char for dissolved atrazine was comparable to that of the corn stillage activated carbon. This similarity could have resulted from the initial organic waste being subjected to a relatively long period of thermal processes during composting, and thus, the compost was more thermally stable when compared with the raw materials. In addition, microorganisms transformed the organic wastes into amorphous humic substances, and thus, it was likely that the microporisity was enhanced. Although this micropore structure could not be detected by the N(2)-BET method, it was apparent in the atrazine sorption experiment. Overall, the experimental results suggested that the compost sample in current study was a relatively stable material thermally for producing char, and that it has the potential as a feed stock for making high-quality activated carbon.

Fuel gas and char from pyrolysis of waste paper in a microwave plasma reactor

Energy Technology Data Exchange (ETDEWEB)

Khongkrapan, Parin; Thanompongchart, Patipat; Tippayawong, Nakorn; Kiatsiriroat, Tanongkiat [Department of Mechanical Engineering, Faculty of Engineering, Chiang Mai University, Chiang Mai 50200 (Thailand)

2013-07-01

In this study, a microwave plasma reactor was used for pyrolysis of waste papers. The effects of different argon flow rates on char and gas generation were investigated. Changes in carbon and oxygen contents from those in paper to char were significant. Char yield of over 25 % was obtained with the heating value of about 38 MJ/kg. Average gas yield and total content of combustible fraction (CO, CH4 and H2) in the gas product were 2.56 m3/kg and 36 %, respectively. The heating value of gas product and carbon conversion efficiency of the process were maximum at 6.0 MJ/m3 and 73 %, respectively.

The influence of fine char particles burnout on bed agglomeration during the fluidized bed combustion of a biomass fuel

Energy Technology Data Exchange (ETDEWEB)

Scala, Fabrizio; Chirone, Riccardo [Istituto di Ricerche sulla Combustione, CNR, P.le V. Tecchio, 80-80125 Naples (Italy); Salatino, Piero [Dipartimento di Ingegneria Chimica, Universita degli Studi di Napoli Federico II, P.le V. Tecchio, 80-80125 Naples (Italy)

2003-11-15

The combustion of biomass char in a bubbling fluidized bed is hereby addressed, with specific reference to the influence that the combustion of fine char particles may exert on ash deposition and bed agglomeration phenomena. Experiments of steady fluidized bed combustion (FBC) of powdered biomass were carried out with the aim of mimicking the postcombustion of attrited char fines generated in the fluidized bed combustion of coarse char. Experimental results showed that the char elutriation rate is much smaller than expected on the basis of the average size of the biomass powder and of the carbon loading in the combustor. Samples of bed material collected after prolonged operation of the combustor were characterized by scanning electron microscopy (SEM)-EDX analysis and revealed the formation of relatively coarse sand-ash-carbon aggregates. The phenomenology is consistent with the establishment of a char phase attached to the bed material as a consequence of adhesion of char fines onto the sand particles. Combustion under sound-assisted fluidization conditions was also tested. As expected, enhancement of fines adhesion on bed material and further reduction of the elutriation rate were observed. Experimental results are interpreted in the light of a simple model which accounts for elutriation of free fines, adhesion of free fines onto bed material and detachment of attached fines by attrition of char-sand aggregates. Combustion of both free and attached char fines is considered. The parameters of the model are assessed on the basis of the measured carbon loadings and elutriation rates. Model computations are directed to estimate the effective size and the peak temperature of char-sand aggregates. The theoretical estimates of the effective aggregate size match fairly well those observed in the experiments.

Effects of chemical form of sodium on the product characteristics of alkali lignin pyrolysis.

Science.gov (United States)

Guo, Da-liang; Yuan, Hong-you; Yin, Xiu-li; Wu, Chuang-zhi; Wu, Shu-bin; Zhou, Zhao-qiu

2014-01-01

The effects of Na as organic bound form or as inorganic salts form on the pyrolysis products characteristics of alkali lignin were investigated by using thermogravimetric analyzer coupled with Fourier transform infrared spectrometry (TG-FTIR), tube furnace and thermo-gravimetric analyzer (TGA). Results of TG-FTIR and tube furnace indicated that the two chemical forms Na reduced the releasing peak temperature of CO and phenols leading to the peak temperature of the maximum mass loss rate shifted to low temperature zone. Furthermore, organic bound Na obviously improved the elimination of alkyl substituent leading to the yields of phenol and guaiacol increased, while inorganic Na increased the elimination of phenolic hydroxyl groups promoting the formation of ethers. It was also found the two chemical forms Na had different effects on the gasification reactivity of chars. For inorganic Na, the char conversion decreased with increasing the char forming temperature, while organic bound Na was opposite. Crown Copyright © 2013. Published by Elsevier Ltd. All rights reserved.

Effect of Kaolin Clay and Alumina on Thermal Performance and Char Morphology of Intumescent fire retardant coating

Directory of Open Access Journals (Sweden)

aziz Hammad

2014-07-01

Full Text Available Intumescent fire retardant coating (IFRC have been developed by using ammonium polyphosphate, expandable graphite, melamine, boric acid, kaolin clay and alumina as fillers bound together with epoxy resin and cured with the help of curing agent. Five different formulations were developed with and without using fillers. Cured samples were burned in furnace at 500°C for 2h for char expansion. Bunsen burner test was performed for 1h using UL-94 vertical burning test to investigate the thermal performance of IFRC. The resultant char obtained after burning of coated samples were characterized by using field emission scanning electron microscopy for char morphology. Char composition was analyzed by using fourier transform infrared spectroscopy. Thermogravimetric analysis was carried out to investigate the residual weight of coating. Results showed that formulation with 0.5 weight % of kaolin clay and 0.5 weight % of alumina provide best thermal performance, uniform and multi-porous char structure with high anti-oxidation property.

Temperature influence on the fast pyrolysis of manure samples: char, bio-oil and gases production

Science.gov (United States)

Fernandez-Lopez, Maria; Anastasakis, Kostas; De Jong, Wiebren; Valverde, Jose Luis; Sanchez-Silva, Luz

2017-11-01

Fast pyrolysis characterization of three dry manure samples was studied using a pyrolyzer. A heating rate of 600°C/s and a holding time of 10 s were selected to reproduce industrial conditions. The effect of the peak pyrolysis temperature (600, 800 and 1000°C) on the pyrolysis product yield and composition was evaluated. Char and bio-oil were gravimetrically quantified. Scanning electron microscopy (SEM) was used to analyse the char structure. H2, CH4, CO and CO2 were measured by means of gas chromatography (GC). A decrease in the char yield and an increase of the gas yield were observed when temperature increased. From 800°C on, it was observed that the char yield of samples Dig R and SW were constant, which indicated that the primary devolatilization reactions stopped. This fact was also corroborated by GC analysis. The bio-oil yield slightly increased with temperature, showing a maximum of 20.7 and 27.8 wt.% for samples Pre and SW, respectively, whereas sample Dig R showed a maximum yield of 16.5 wt.% at 800°C. CO2 and CO were the main released gases whereas H2 and CH4 production increased with temperature. Finally, an increase of char porosity was observed with temperature.

Disintegration of beech wood char during thermal conversion

DEFF Research Database (Denmark)

Hindsgaul, Claus

In the present work the processes occurring in the structures of slowly pyrolysed beech wood char during thermal gasification have been investigated. Emphasis was put on physical changes and gas transport properties during conversion. The highly anisotropic structure of wood was preserved in its ...

Phosphorus recovery from sewage sludge char ash

NARCIS (Netherlands)

Atienza-Martinez, M.; Gea, G.; Arauzo, J.; Kersten, Sascha R.A.; Kootstra, A.M.J.

2014-01-01

Phosphorus was recovered from the ash obtained after combustion at different temperatures (600 °C, 750 °C and 900 °C) and after gasification (at 820 °C using a mixture of air and steam as fluidising agent) of char from sewage sludge fast pyrolysis carried out at 530 °C. Depending on the leaching

Char characterization and DTF assays as tools to predict burnout of coal blends in power plants

Energy Technology Data Exchange (ETDEWEB)

C. Ulloa; A.G. Borrego; S. Helle; A.L. Gordon; X. Garcia [Universidad de Concepcion, Concepcion (Chile). Departamento de Ingenieria Quimica

2005-02-01

The aim of this study is to predict efficiency deviations in the combustion of coal blends in power plants. Combustion of blends, as compared to its single coals, shows that for some blends the behavior is non-additive in nature. Samples of coal feed and fly ashes from combustion of blends at two power plants, plus chars of the parent coals generated in a drop-tube furnace (DTF) at temperatures and heating rates similar to those found in the industrial boilers were used. Intrinsic kinetic parameters, burning profiles and petrographic characteristics of these chars correlated well with the burnout in power plants and DTF experiments. The blend combustion in a DTF reproduces both positive and negative burnout deviations from the expected weighted average. These burnout deviations have been previously attributed to parallel or parallel-series pathways of competition for oxygen. No deviations were found for blends of low rank coals of similar characteristics yielding chars close in morphology, optical texture and reactivity. Negative deviations were found for blends of coals differing moderately in rank and were interpreted as associated with long periods of competition. In this case, fly-ashes were enriched in material derived from the least reactive char, but also unburnt material attributed to the most reactive char was identified. Improved burnout compared to the weighted average was observed for blends of coals very different in rank, and interpreted as the result of a short interaction period, followed by a period where the less reactive char burns under conditions that are more favorable to its combustion. In this case, only unburned material from the least reactive char was identified in the fly-ashes. 20 refs., 9 figs., 5 tabs.

Nitric oxide reduction in coal combustion: role of char surface complexes in heterogeneous reactions.

Science.gov (United States)

Arenillas, Ana; Rubiera, Fernando; Pis, José J

2002-12-15

Nitrogen oxides are one of the major environmental problems arising from fossil fuel combustion. Coal char is relatively rich in nitrogen, and so this is an important source of nitrogen oxides during coal combustion. However, due to its carbonaceous nature, char can also reduce NO through heterogeneous reduction. The objectives of this work were on one hand to compare NO emissions from coal combustion in two different types of equipment and on the other hand to study the influence of char surface chemistry on NO reduction. A series of combustion tests were carried out in two different scale devices: a thermogravimetric analyzer coupled to a mass spectrometer and an FTIR (TG-MS-FTIR) and a fluidized bed reactor with an on line battery of analyzers. The TG-MS-FTIR system was also used to perform a specific study on NO heterogeneous reduction reactions using chars with different surface chemistry. According to the results obtained, it can be said that the TG-MS-FTIR system provides valuable information about NO heterogeneous reduction and it can give good trends of the behavior in other combustion equipments (i.e., fluidized bed combustors). It has been also pointed out that NO-char interaction depends to a large extent on temperature. In the low-temperature range (800 degrees C), a different mechanism is involved in NO heterogeneous reduction, the nature of the carbon matrix being a key factor.

Bio-oil and bio-char production from biomass and their structural analyses

International Nuclear Information System (INIS)

Kilic, Murat; Özsin, Gamzenur; Pütün, Ayşe E.; Pütün, Ersan

2015-01-01

Energy demand is increasing day by day because of the rapid developments in the population, industrialization and urbanisation. Since, fossil fuels will be at the verge of getting extinct, researches are mostly focused on the renewable sources, such as biomass, in recent years. This paper provides an environmentally friendly process to convert waste biomass samples to bio-oil and bio-char by pyrolysis. For this purpose, pyrolysis characteristics of pomegranate peels under inert atmosphere were studied by using both TGA to analysis decomposition behaviour and a batch reactor to investigate product yields and properties. The properties of bio-oil and bio-char were investigated by different analytical techniques such as GC-MS, FT-IR, SEM, He pycnometry and elemental analysis. As a consequence, it is possible to obtain bio-oil, which has similar properties like petroleum hydrocarbons, and to obtain bio-char, which can be further used as a solid fuel or a carbonaceous adsorbent material via pyrolysis process. (full text)

Investigation of the Anisotropic Behavior of Wood Char Particles during Gasification

DEFF Research Database (Denmark)

Henriksen, Ulrik Birk; Hindsgaul, Claus; Qvale, Einar Bjørn

2006-01-01

(R) and tangential (T) directions. Despite this, this property has normally not been included in mathematical model descriptions of gasification of thermally thick particles. The present paper describes a study of the influence of the anisotropy on the reactivity of thermally thick char particles...... of the normal to the greater surface of the slabs L, R, or T (see Figure 8). When the smaller surfaces were coated with alumina silicate, the gasification agent could only enter the interior of the slabs through the greater surfaces. Thermally thick char particles from beech and pine reacted more slowly...

CHAR and BURNMAC - burnup modules of the AUS neutronics code system

International Nuclear Information System (INIS)

Robinson, G.S.

1986-03-01

In the AUS neutronics code system, the burnup module CHAR solves the nuclide depletion equations by an analytic technique in a number of spatial zones. CHAR is usually used as one component of a lattice burnup calculation but contains features which also make it suitable for some global burnup calculations. BURNMAC is a simple accounting module based on the assumption that cross sections for a rector zone depend only on irradiation. BURNMAC is used as one component of a global calculation in which burnup is achieved by interpolation in the cross sections produced from a previous lattice calculation

Investigation of char strength and expansion properties of an intumescent coating exposed to rapid heating rates

DEFF Research Database (Denmark)

Nørgaard, Kristian Petersen; Dam-Johansen, Kim; Català, Pere

2013-01-01

, char properties, measured at room temperature, were dependent on the preceding storage conditions (in air or in a desiccator). The char was found to have the highest mechanical strength against compression in the outer crust facing the heat source. For thin (147μm) free coating films, a tendency...... with respect to the mechanical resistance against compression, degree of expansion, and residual mass fraction. Experimental results show that when using this type of shock heating, the mechanical resistance of the char against compression cannot meaningfully be correlated to the expansion factor. In addition...

Quantitative Analysis of Graphene Sheet Content in Wood Char Powders during Catalytic Pyrolysis

Institute of Scientific and Technical Information of China (English)

Yan-Jia Liou; Wu-Jang Huang

2013-01-01

The quantitative characterization of the graphene sheet content in carbon-containing materials is arguable and has not yet been developed.The authors report on a feasible method to characterize graphene sheet content quantitatively in pyrolized carbon materials using an X-ray diffraction (XRD) spectrometer.A direct carbonation at 300 ℃ followed by catalytic pyrolysis (heat-treatment temperature was set at 700-1400 ℃)under a vacuum condition was used for turning wood waste into pyrolized wood char powders.The graphene content in the samples was calculated through an analysis of full width at half maximum (FWHM) of the carbon (100) crystal plane at around 42°-43° in XRD.Results showed that the FWHM and the calculated graphene sheet content of pyrolized wood char powders depended on the heat-treatment temperature,and the FWHM of wood char powder with well-developed graphene sheets (100％) was determined to be 5.0.In addition,the trend to 100％ graphene sheet-contained pyrolized carbon powder was obtained at a heattreatment temperature of 2700 ℃.The resistivity of the wood char powder with 100％ graphene sheets was predicted to be 0.01 Ω cm,close to our experimental data of 0.012 and 0.006 Ω cm for commercial graphite and graphene products,respectively.

Influence of coal rank and pyrolysis/hydropyrolysis temperature on nitrogen oxide emission during coal char combustion

Energy Technology Data Exchange (ETDEWEB)

Stanczyk, K.; Miga, K. [Polish Academy of Sciences, Gliwice (Poland). Institute of Coal Chemistry

1999-07-01

The formation of NO during the combustion of chars was investigated. The formation of NO was correlated with carbon oxides emission. The way in which the reactivity of chars influences NO emission was investigated. 6 refs., 2 figs., 2 tabs.

The effect of temperature and heating rate on char properties obtained from solar pyrolysis of beech wood.

Science.gov (United States)

Zeng, Kuo; Minh, Doan Pham; Gauthier, Daniel; Weiss-Hortala, Elsa; Nzihou, Ange; Flamant, Gilles

2015-04-01

Char samples were produced from pyrolysis in a lab-scale solar reactor. The pyrolysis of beech wood was carried out at temperatures ranging from 600 to 2000°C, with heating rates from 5 to 450°C/s. CHNS, scanning electron microscopy analysis, X-ray diffractometry, Brunauer-Emmett-Teller adsorption were employed to investigate the effect of temperature and heating rate on char composition and structure. The results indicated that char structure was more and more ordered with temperature increase and heating rate decrease (higher than 50°C/s). The surface area and pore volume firstly increased with temperature and reached maximum at 1200°C then reduced significantly at 2000°C. Besides, they firstly increased with heating rate and then decreased slightly at heating rate of 450°C/s when final temperature was no lower than 1200°C. Char reactivity measured by TGA analysis was found to correlate with the evolution of char surface area and pore volume with temperature and heating rate. Copyright © 2015 Elsevier Ltd. All rights reserved.

Temperature influence on the fast pyrolysis of manure samples: char, bio-oil and gases production

Directory of Open Access Journals (Sweden)

Fernandez-Lopez Maria

2017-01-01

Full Text Available Fast pyrolysis characterization of three dry manure samples was studied using a pyrolyzer. A heating rate of 600°C/s and a holding time of 10 s were selected to reproduce industrial conditions. The effect of the peak pyrolysis temperature (600, 800 and 1000°C on the pyrolysis product yield and composition was evaluated. Char and bio-oil were gravimetrically quantified. Scanning electron microscopy (SEM was used to analyse the char structure. H2, CH4, CO and CO2 were measured by means of gas chromatography (GC. A decrease in the char yield and an increase of the gas yield were observed when temperature increased. From 800°C on, it was observed that the char yield of samples Dig R and SW were constant, which indicated that the primary devolatilization reactions stopped. This fact was also corroborated by GC analysis. The bio-oil yield slightly increased with temperature, showing a maximum of 20.7 and 27.8 wt.% for samples Pre and SW, respectively, whereas sample Dig R showed a maximum yield of 16.5 wt.% at 800°C. CO2 and CO were the main released gases whereas H2 and CH4 production increased with temperature. Finally, an increase of char porosity was observed with temperature.

Investigation on the fast co-pyrolysis of sewage sludge with biomass and the combustion reactivity of residual char.

Science.gov (United States)

Deng, Shuanghui; Tan, Houzhang; Wang, Xuebin; Yang, Fuxin; Cao, Ruijie; Wang, Zhao; Ruan, Renhui

2017-09-01

Gaining the valuable fuels from sewage sludge is a promising method. In this work, the fast pyrolysis characteristics of sewage sludge (SS), wheat straw (WS) and their mixtures in different proportions were carried out in a drop-tube reactor. The combustion reactivity of the residual char obtained was investigated in a thermogravimetric analyzer (TGA). Results indicate that SS and WS at different pyrolysis temperatures yielded different characteristic gas compositions and product distributions. The co-pyrolysis of SS with WS showed that there existed a synergistic effect in terms of higher gas and bio-oil yields and lower char yield, especially at the WS adding percentage of 80wt%. The addition of WS to SS increased the carbon content in the SS char and improved char porous structures, resulting in an improvement in the combustion reactivity of the SS char. The research results can be used to promote co-utilization of sewage sludge and biomass. Copyright © 2017. Published by Elsevier Ltd.

Heat Transfer in a Fixed Biomass Char Bed

DEFF Research Database (Denmark)

Fjellerup, Jan Søren; Henriksen, Ulrik Birk; Glarborg, P.

2002-01-01

A thermal conductivity model based on the Yagi and Kunii model together with a bed model was developed to describe the thermal conductivity of a straw char bed. The bed model describes the relationship between the distance between particles and the external porosity. To verify the model, thermal ...

All-fiber maskless lithographic technology to form microcircular interference pattern on Azo polymer film

Science.gov (United States)

Kim, Junki; Jung, Yongmin; Oh, Kyunghwan; Chun, Chaemin; Hong, Jeachul; Kim, Dongyu

2005-03-01

We report a novel all-fiber, maskless lithograpic technology to form various concentric grating patterns for micro zone plate on azo polymer film. The proposed technology is based on the interference pattern out of the cleaved end of a coreless silica fiber (CSF)-single mode fiber (SMF) composite. The light guided along SMF expands into the CSF segment to generate various circular interference patterns depending on the length of CSF. Interference patterns are experimentally observed when the CSF length is over a certain length and the finer spacing between the concentric rings are obtained for a longer CSF. By using beam propagation method (BPM) package, we could further investigated the concentric interference patterns in terms of intensity distribution and fringe spacing as a function of CSF length. These intereference patterns are directly projected over azo polymer film and their intensity distrubution formed surface relief grating (SRG) patterns. Compared to photoresist films azo polymer layers produce surface relief grating (SRG), where the actual mass of layer is modulated rather than refractive index. The geometric parameters of the CSF length as well as diameter and the spacing between the cleaved end of a CSF and azo polymer film, were found to play a major role to generate various concentric structures. With the demonstration of the circular SRG patterns, we confirmed that the proposed technique do have an ample potential to fabricate micro fresnel zone plate, that could find applications in lens arrays for optical beam formings as well as compact photonic devices.

Synthesis and characterization of organic-inorganic hybrids formed between conducting polymers and crystalline antimonic acid

Directory of Open Access Journals (Sweden)

Beleze Fábio A.

2001-01-01

Full Text Available In this paper we report the synthesis and characterization of novel organic-inorganic hybrid materials between the crystalline antimonic acid (CAA and two conductive polymers: polypyrrole and polyaniline. The hybrids were obtained by in situ oxidative polymerization of monomers by the Sb(V present in the pyrochlore-like CAA structure. The materials were characterized by infrared and Raman spectroscopy, X-ray diffraction, cyclic voltammetry, CHN elemental analysis and electronic paramagnetic resonance spectroscopy. The results showed that both polymers were formed in their oxidized form, with the CAA structure acting as a counter anion.

Fluidized bed combustion of single coal char particles at high CO{sub 2} concentration

Energy Technology Data Exchange (ETDEWEB)

Scala, F.; Chirone, R. [CNR, Naples (Italy)

2010-12-15

Combustion of single coal char particles was studied at 850{sup o}C in a lab-scale fluidized bed at high CO{sub 2} concentration, typical of oxyfiring conditions. The burning rate of the particles was followed as a function of time by continuously measuring the outlet CO and O{sub 2} concentrations. Some preliminary evaluations on the significance of homogeneous CO oxidation in the reactor and of carbon gasification by CO{sub 2} in the char were also carried out. Results showed that the carbon burning rate increases with oxygen concentration and char particle size. The particle temperature is approximately equal to that of the bed up to an oxygen concentration of 2%, but it is considerably higher for larger oxygen concentrations. Both CO{sub 2} gasification of char and homogeneous CO oxidation are not negligible. The gasification reaction rate is slow and it is likely to be controlled by intrinsic kinetics. During purely gasification conditions the extent of carbon loss due to particle attrition by abrasion (estimated from the carbon mass balance) appears to be much more important than under combustion conditions.

Characterization of char derived from various types of solid wastes from the standpoint of fuel recovery and pretreatment before landfilling

International Nuclear Information System (INIS)

Hwang, I.H.; Matsuto, T.; Tanaka, N.; Sasaki, Y.; Tanaami, K.

2007-01-01

Carbonization is a kind of pyrolysis process to produce char from organic materials under an inert atmosphere. In this work, chars derived from various solid wastes were characterized from the standpoint of fuel recovery and pretreatment of waste before landfilling. Sixteen kinds of municipal and industrial solid wastes such as residential combustible wastes, non-combustible wastes, bulky wastes, construction and demolition wastes, auto shredder residue, and sludges were carbonized at 500 deg. C for 1 h under nitrogen atmosphere. In order to evaluate the quality of char as fuel, proximate analysis and heating value were examined. The composition of raw waste had a significant influence on the quality of produced char. The higher the ratio of woody biomass in waste, the higher heating value of char produced. Moreover, an equation to estimate heating value of char was developed by using the weight fraction of fixed carbon and volatile matter in char. De-ashing and chlorine removal were performed to improve the quality of char. The pulverization and sieving method seems to be effective for separation of incombustibles such as metal rather than ash. Most char met a 0.5 wt% chlorine criterion for utilization as fuel in a shaft blast furnace after it was subjected to repeated water-washing. Carbonization could remove a considerable amount of organic matter from raw waste. In addition, the leaching of heavy metals such as chrome, cadmium, and lead appears to be significantly suppressed by carbonization regardless of the type of raw waste. From these results, carbonization could be considered as a pretreatment method for waste before landfilling, as well as for fuel recovery

Rationalising polymer selection for supersaturated film forming systems produced by an aerosol spray for the transdermal delivery of methylphenidate.

Science.gov (United States)

Edwards, A; Qi, S; Liu, F; Brown, M B; McAuley, W J

2017-05-01

Film forming systems offer a number of advantages for topical and transdermal drug delivery, in particular enabling production of a supersaturated state which can greatly improve drug absorption and bioavailability. However the suitability of individual film forming polymers to stabilise the supersaturated state and optimise delivery of drugs is not well understood. This study reports the use of differential scanning calorimetry (DSC) to measure the solubility of methylphenidate both as the free base and as the hydrochloride salt in two polymethacrylate copolymers, Eudragit RS (EuRS) and Eudragit E (EuE) and relates this to the ability of films formed using these polymers to deliver methylphenidate across a model membrane. EuRS provided greater methylphenidate delivery when the drug was formulated as the free base in comparison EuE because the lower solubility of the drug in EuRS provided a higher degree of drug saturation in the polymeric film. In contrast EuE provided greater delivery of methylphenidate hydrochloride as EuRS could not prevent its crystallisation from a supersaturated state. Methylphenidate flux across the membrane could be directly related to degree of saturation of the drug in the film formulation as estimated by the drug solubility in the individual polymers demonstrating the importance of drug solubility in the polymer included in film forming systems for topical/transdermal drug delivery. In addition DSC has been demonstrated to be a useful tool for determining the solubility of drugs in polymers used in film forming systems and the approaches outlined here are likely to be useful for predicting the suitability of polymers for particular drugs in film forming transdermal drug delivery systems. Copyright © 2017. Published by Elsevier B.V.

Changes of wood anatomical characters of selected species of Araucaria- during artificial charring - implications for palaeontology

Directory of Open Access Journals (Sweden)

Isa Carla Osterkamp

2017-11-01

Full Text Available ABSTRACT Charcoal is widely accepted as evidence of the occurrence of palaeo-wildfire. Although fossil charcoal remains have been used in many studies, investigation into the anatomical changes occurring during charring are few. The present study analyses changes in selected anatomical characters during artificial charring of modern wood of three species of the genus Araucaria (i.e. Araucaria angustifolia, Araucaria bidwillii and Araucaria columnaris. Wood samples of the studied species was charred under controlled conditions at varying temperatures. Measurements of anatomical features of uncharred wood and artificial charcoal were statistically analysed. The anatomical changes were statistically correlated with charring temperatures and most of the parameters showed marked decreases with increasing charring temperature. Compared to the intrinsic variability in anatomical features, both within and between growth rings of an individual plant, the changes induced by temperature account only for a comparatively small percentage of the observed variability. Regarding Araucaria charcoal, it seems possible that at least general taxonomic and palaeoenvironmental implications can be drawn from such material. However, it is not clear so far whether these results and interpretations based on only three taxa, can be generalized for the entire family and anatomically similar fossil taxa or not.

Influence of char texture and volatile matter content on NO emissions

Energy Technology Data Exchange (ETDEWEB)

Arenillas, A.; Rubiera, F.; Parra, J.B.; Moreno, A.H.; Pis, J.J. [Inst. National Vacional del Carbon, Oviedo (Spain)

1997-12-31

A low volatile bituminous coal was pyrolysed in a quartz reactor under nitrogen at different heating rates (5, 10, 50 and 150 C/min) up to a final temperature of 850 C. Textural characterisation (mercury porosimetry, adsorption isotherms of N{sub 2} and CO{sub 2}, ASA) of the chars was carried out in order to study the influence of textural properties on char reactivity and NO emissions. The role of volatile matter content in the emission of nitrogen compounds was also investigated. A thermogravimetric analyser linked to a quadrupole mass spectrometer (TG-MS) was used to study the compounds evolved during pyrolysis and combustion. (orig.)

The effects of gamma radiation on polymer matrix waste forms

International Nuclear Information System (INIS)

Johnson, D.I.; Burnay, S.G.; Phillips, D.C.

1986-06-01

A study has been made of the volume and weight changes, mechanical properties, and radiolytic gas production of polymer matrix waste forms during γ irradiation in open containers. The work has been commissioned by the Department of the Environment as part of its radioactive waste management research programme. The materials included polyester, vinyl ester, epoxide and polystyrene resins containing ion exchangers; and polyester and epoxide resins containing a PWR evaporator concentrate. (author)

Physicochemical characterization of in situ drug-polymer nanocomplex formed between zwitterionic drug and ionomeric material in aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Salamanca, Constain H., E-mail: chsalamanca@icesi.edu.co [Pharmaceutical physical chemistry laboratory, Department of Pharmacy, Faculty of Natural Sciences, ICESI University, Cali (Colombia); Castillo, Duvan F.; Villada, Juan D. [Pharmaceutical physical chemistry laboratory, Department of Pharmacy, Faculty of Natural Sciences, ICESI University, Cali (Colombia); Rivera, Gustavo R. [SIT Biotech GmbH, BMZ 2 Otto-Hahn-Str. 15, 44227 Dortmund (Germany)

2017-03-01

Biocompatible polymeric materials with the potential to form functional structures, in association with different therapeutic molecules, in physiological media, represent a great potential for biological and pharmaceutical applications. Therefore, here the formation of a nano-complex between a synthetic cationic polymer and model drug (ampicillin trihydrate) was studied. The formed complex was characterized by size and zeta potential measurements, using dynamic light scattering and capillary electrophoresis. Moreover, the chemical and thermodynamically stability of these complexes were studied. The ionomeric material, here referred as EuCl, was obtained by equimolar reaction between Eudragit E and HCl. The structural characterization was carried out by potentiometric titration, FTIR spectroscopy, and DSC. The effect of pH, time, polymer concentration and ampicillin/polymer molar ratio over the hydrodynamic diameter and zeta potential were established. The results show that EuCl ionomer in aqueous media presents two different populations of nanoparticles; one of this tends to form flocculated aggregates in high pH and concentrations, by acquiring different conformations in solution by changing from a compact to an extended conformation. Moreover, the formation of an in situ interfacial polymer-drug complex was demonstrated, this could slightly reduce the hydrolytic degradation of the drug while affecting its solubility, mainly under acidic conditions. - Highlights: • The EuCl ionomer in aqueous media presents two different populations of nanoparticle, corresponding to proximally 15 nm and 150 nm. • The EuCl ionomer in aqueous media may form different structure depending on the pH and polymer concentration, which tends to form flocculated aggregates in high pH and concentrations. • The formation of an in situ interfacial polymer-drug complex was demonstrated, which could slightly reduce the hydrolytic degradation of the drug and affecting its solubility in

Mechanically Strong Aerogels Formed by Templated Growth of Polymer Cross- Linkers on Inorganic Nanoparticles

Science.gov (United States)

Leventis, Nicholas; Fabrizio, Eve F.; Johnston, Chris; Meador, Maryann

2004-01-01

In the search for materials with better mechanical, thermal, and electrical properties, it is becoming evident that oftentimes dispersing ceramic nanoparticles in plastics improves performance. Along these lines, chemical bonding (both covalent and noncovalent) between a filler and a polymer improves their compatibility, and thus enhances certain properties of the polymeric matrix above and beyond what is accomplished by simple doping with the filler. When a similarly sized dopant and matrix are used, elementary building blocks may also have certain distinct advantages (e.g., in catalysis). In this context, researchers at the NASA Glenn Research Center reasoned that in the extreme case, where the dopant and the matrix (e.g., a filler and a polymer) are not only sized similarly, but their relative amounts are comparable, the relative roles of the dopant and matrix can be reversed. Then, if the "filler," or a certain form thereof, possesses desirable properties of its own, such properties could be magnified by cross-linking with a polymer. We at Glenn have identified silica as such a filler in its lowest-density form, namely the silica aerogel.

Temperature induced development of porous structure of bituminous coal chars at high pressure

Directory of Open Access Journals (Sweden)

Natalia Howaniec

2016-01-01

Full Text Available The porous structure of chars affects their reactivity in gasification, having an impact on the course and product distribution of the process. The shape, size and connections between pores determine the mechanical properties of chars, as well as heat and mass transport in thermochemical processing. In the study the combined effects of temperature in the range of 973–1273 °K and elevated pressure of 3 MPa on the development of porous structure of bituminous coal chars were investigated. Relatively low heating rate and long residence time characteristic for the in-situ coal conversion were applied. The increase in the temperature to 1173 °K under pressurized conditions resulted in the enhancement of porous structure development reflected in the values of the specific surface area, total pore volume, micropore area and volume, as well as ratio of the micropore volume to the total pore volume. These effects were attributed to the enhanced vaporization and devolatilization, as well as swelling behavior along the increase of temperature and under high pressure, followed by a collapse of pores over certain temperature value. This proves the strong dependence of the porous structure of chars not only on the pyrolysis process conditions but also on the physical and chemical properties of the parent fuel.

Supercooled dynamics of glass-forming liquids and polymers under hydrostatic pressure

Energy Technology Data Exchange (ETDEWEB)

Roland, C M [Naval Research Laboratory, Chemistry Division, Code 6120, Washington, DC 20375-5342 (United States); Hensel-Bielowka, S [Institute of Physics, Silesian University, ul. Uniwersytecka 4, 40-007 Katowice (Poland); Paluch, M [Institute of Physics, Silesian University, ul. Uniwersytecka 4, 40-007 Katowice (Poland); Casalini, R [Naval Research Laboratory, Chemistry Division, Code 6120, Washington, DC 20375-5342 (United States); Chemistry Department, George Mason University, Fairfax, VA 22030 (United States)

2005-06-01

An intriguing problem in condensed matter physics is understanding the glass transition, in particular the dynamics in the equilibrium liquid close to vitrification. Recent advances have been made by using hydrostatic pressure as an experimental variable. These results are reviewed, with an emphasis in the insight provided into the mechanisms underlying the relaxation properties of glass-forming liquids and polymers.

Are forestation, bio-char and landfilled biomass adequate offsets for the climate effects of burning fossil fuels?

International Nuclear Information System (INIS)

Reijnders, L.

2009-01-01

Forestation and landfilling purpose-grown biomass are not adequate offsets for the CO 2 emission from burning fossil fuels. Their permanence is insufficiently guaranteed and landfilling purpose-grown biomass may even be counterproductive. As to permanence, bio-char may do better than forests or landfilled biomass, but there are major uncertainties about net greenhouse gas emissions linked to the bio-char life cycle, which necessitate suspension of judgement about the adequacy of bio-char addition to soils as an offset for CO 2 emissions from burning fossil fuels.

Synthesis of palm oil empty fruit bunch magnetic pyrolytic char impregnating with FeCl3 by microwave heating technique

International Nuclear Information System (INIS)

Mubarak, N.M.; Kundu, A.; Sahu, J.N.; Abdullah, E.C.; Jayakumar, N.S.

2014-01-01

Empty fruit bunch (EFB) is one of the most abundant residues of the Palm oil mill industry in Malaysia. The novel magnetic bio-char was synthesized by single stage microwave heating technique, using EFB in the presence of ferric chloride hexahydrate. The effect of microwave powers, radiation time and impregnation ratio (IR) of ferric chloride hexahydrate to biomass were studied. Also the process parameters such as microwave powers, radiation times and IR were optimized using response surface method. The statistical analysis revealed that the optimum conditions for the high porosity magnetic bio-char production were at 900 W microwave power, 20 min radiation time and 0.5 (FeCl 3 : biomass) impregnation ratio. These newly produced magnetic bio-char have a high surface area of 890 m 2  g −1 and that leads to highly efficient in the removal of methylene blue (MB) with an efficiency of 99.9% from aqueous solution with a maximum adsorption capacity of 265 mg g −1 . - Highlights: • Magnetic bio-char production using discarded material EFB with chemical activation. • Single stage synthesis of magnetic bioc-har via microwave heating was narrated. • Effect of each process parameters on synthesis of magnetic bio-char was elaborated. • Magnetic bio-char has high surface area, high porosity and high adsorption capacity. • Novel magnetic bio-char adds new dimension to the materials as an adsorbent

Properties and Beneficial Uses of (BioChars, with Special Attention to Products from Sewage Sludge Pyrolysis

Directory of Open Access Journals (Sweden)

Arianna Callegari

2018-03-01

Full Text Available Residual sludge disposal costs may constitute up to, and sometimes above, 50% of the total cost of operation of a Wastewater Treatment Plant (WWTP and contribute approximately 40% of the total greenhouse gas (GHG emissions associated with its operation. Traditionally, wastewater sludges are processed for: (a reduction of total weight and volume to facilitate their transfer and subsequent treatments; (b stabilization of contained organic material and destruction of pathogenic microorganisms, elimination of noxious odors, and reduction of putrefaction potential and, at an increasing degree; (c value addition by developing economically viable recovery of energy and residual constituents. Among several other processes, pyrolysis of sludge biomass is being experimented with by some researchers. From the process, oil with composition not dissimilar to that of biodiesels, syngas, and a solid residue can be obtained. While the advantage of obtaining sludge-derived liquid and gaseous fuels is obvious to most, the solid residue from the process, or char (also indicated as biochar by many, may also have several useful, initially unexpected applications. Recently, the char fraction is getting attention from the scientific community due to its potential to improve agricultural soils’ productivity, remediate contaminated soils, and supposed, possible mitigation effects on climate change. This paper first discusses sludge-pyrolysis-derived char production fundamentals (including relationships between char, bio-oil, and syngas fractions in different process operating conditions, general char properties, and possible beneficial uses. Then, based on current authors’ experiments with microwave-assisted sludge pyrolysis aimed at maximization of liquid fuel extraction, evaluate specific produced char characteristics and production to define its properties and most appropriate beneficial use applications in this type of setting.

Cationic polymers in water treatment: Part 2: Filterability of CPE-formed suspension

Czech Academy of Sciences Publication Activity Database

Polášek, P.; Mutl, Silvestr

2002-01-01

Roč. 28, č. 1 (2002), s. 83-88 ISSN 0378-4738 R&D Projects: GA AV ČR KSK2067107 Institutional research plan: CEZ:AV0Z2060917 Keywords : cationic polymers * water treatment * filterability of CPE-formed suspension Subject RIV: BK - Fluid Dynamics Impact factor: 0.481, year: 2002

The effect of the textural properties of bituminous coal chars on NO emissions

Energy Technology Data Exchange (ETDEWEB)

Arenillas, A.; Rubiera, F.; Pis, J.J.; Jones, J.M.; Williams, A. [CSIC, Oviedo (Spain). Inst. Nacional del Carbon

1999-11-01

NO is the primary product of the oxidation of char nitrogen, and in some combustion processes the NO can be reduced on the char surface to give N{sub 2}O and/or N{sub 2}. In this study a range of bituminous coal (low, medium and high volatile matter content) were pyrolysed in a fixed bed reactor at various heating rates. Textural characterisation was carried out by measuring true (He) and apparent (Hg) densities and N{sub 2} (-196{degree}C) and CO{sub 2} (0{degree}C) adsorption isotherms. Pore volume distributions and surface areas were obtained for the chars studied. A thermogravimetric analyser coupled to a quadrupole mass spectrometer (TG-MS) was used to study the combustion behaviour of the samples and the nitrogen compounds evolved during temperature-programmed combustion. Results are discussed in terms of the influence of both textural properties and reactivity on NO emissions and on the heterogeneous reduction of NO. 23 refs., 8 figs., 4 tabs.

Review of oxidative degradations of certain heterocyclic polymers

Science.gov (United States)

Mayo, F. R.

1971-01-01

The curing and decompositions of polyphenylenes and several nitrogen-containing condensation polymers, particularly polybenzimidazoles and pyrones, are reviewed critically. It is concluded that the condensations are usually imperfect and incomplete and that in most of the published work the late stages of the condensation are complicated by the beginnings of the charring and carbonization processes. Most discussions of mechanisms in this range are highly speculative and of little value. The most promising fields for further research are at lower temperatures, where slow oxidation processes deserve study, and at higher temperatures, where it may be possible to influence carbonization processes to obtain better products.

Impact of contamination and pre-treatment on stable carbon and nitrogen isotopic composition of charred plant remains.

Science.gov (United States)

Vaiglova, Petra; Snoeck, Christophe; Nitsch, Erika; Bogaard, Amy; Lee-Thorp, Julia

2014-12-15

Stable isotope analysis of archaeological charred plants has become a useful tool for interpreting past agricultural practices and refining ancient dietary reconstruction. Charred material that lay buried in soil for millennia, however, is susceptible to various kinds of contamination, whose impact on the grain/seed isotopic composition is poorly understood. Pre-treatment protocols have been adapted in distinct forms from radiocarbon dating, but insufficient research has been carried out on evaluating their effectiveness and necessity for stable carbon and nitrogen isotope analysis. The effects of previously used pre-treatment protocols on the isotopic composition of archaeological and modern sets of samples were investigated. An archaeological sample was also artificially contaminated with carbonates, nitrates and humic acid and subjected to treatment aimed at removing the introduced contamination. The presence and removal of the contamination were investigated using Fourier transform infrared spectroscopy (FTIR) and δ(13)C and δ(15)N values. The results show a ca 1‰ decrease in the δ(15)N values of archaeological charred plant material caused by harsh acid treatments and ultra-sonication. This change is interpreted as being caused by mechanical distortion of the grains/seeds rather than by the removal of contamination. Furthermore, specific infrared peaks have been identified that can be used to detect the three types of contaminants studied. We argue that it is not necessary to try to remove humic acid contamination for stable isotope analysis. The advantages and disadvantages of crushing the grains/seeds before pre-treatment are discussed. We recommend the use of an acid-only procedure (0.5 M HCl for 30 min at 80 °C followed by three rinses in distilled water) for cleaning charred plant remains. This study fills an important gap in plant stable isotope research that will enable future researchers to evaluate potential sources of isotopic change and pre

Anadromous char as an alternate food choice to marine animals: A synthesis of Hg concentrations, population features and other influencing factors

Energy Technology Data Exchange (ETDEWEB)

Evans, Marlene S., E-mail: marlene.evans@ec.gc.ca [Environment Canada, Water Science and Technology Directorate, 11 Innovation Blvd., Saskatoon SK S7N 3H5 (Canada); Muir, Derek C.G. [Environment Canada, Water Science and Technology Directorate, 867 Lakeshore Rd., Burlington, ON L7R 4A6 (Canada); Keating, Jonathan [Environment Canada, Water Science and Technology Directorate, 11 Innovation Blvd., Saskatoon SK S7N 3H5 (Canada); Wang, Xiaowa [Environment Canada, Water Science and Technology Directorate, 867 Lakeshore Rd., Burlington, ON L7R 4A6 (Canada)

2015-03-15

This study was conducted to confirm sporadic measurements made over the late 1970s to the early 1990s which determined that mercury (Hg) concentrations were low in anadromous char across Arctic and subarctic Canada including northern Québec and Labrador. Over 2004–2013, anadromous char populations across northern Canada were investigated at 20 sites for Hg concentrations and life history characteristics. Hg concentrations were extremely low in anadromous char muscle, typically < 0.05 μg/g (wet weight) and, at each location, generally increased with fish length, age and nitrogen isotope (δ{sup 15}N) ratio and decreased with condition factor and %lipid; correlations with carbon isotope (δ{sup 13}C) ratio were inconsistent. Location and year were significant variables influencing Hg concentrations over the study area; longitude and latitude also were significant influencing variables. Char length, weight, age, condition factor and lipid content explained additional variance. A tendency towards higher Hg concentrations with increasing latitude may be partially related to decreasing growth of char towards the north. However, Hg concentrations in char were positively correlated with growth rates suggesting that Hg concentrations in char also were higher in the more productive study areas, including to the west where mainland riverine inputs of terrestrial carbon, nutrients, and Hg were greater. The data base for assessing time trends in char was limited by the small number of years investigated at most locations, variable fish size across years, small sample size, etc. Where temporal trends were detected, they were of increase on the long term (1970s, 1980s or early 1990s to the present) but of decrease on the short term (early 2000s to present) with Nain (Labrador) showing the converse pattern. Higher Hg concentrations were also related to lower condition factor and cooler springs. Hg concentrations in anadromous char are compared with other terrestrial, aquatic

Anadromous char as an alternate food choice to marine animals: A synthesis of Hg concentrations, population features and other influencing factors

International Nuclear Information System (INIS)

Evans, Marlene S.; Muir, Derek C.G.; Keating, Jonathan; Wang, Xiaowa

2015-01-01

This study was conducted to confirm sporadic measurements made over the late 1970s to the early 1990s which determined that mercury (Hg) concentrations were low in anadromous char across Arctic and subarctic Canada including northern Québec and Labrador. Over 2004–2013, anadromous char populations across northern Canada were investigated at 20 sites for Hg concentrations and life history characteristics. Hg concentrations were extremely low in anadromous char muscle, typically < 0.05 μg/g (wet weight) and, at each location, generally increased with fish length, age and nitrogen isotope (δ 15 N) ratio and decreased with condition factor and %lipid; correlations with carbon isotope (δ 13 C) ratio were inconsistent. Location and year were significant variables influencing Hg concentrations over the study area; longitude and latitude also were significant influencing variables. Char length, weight, age, condition factor and lipid content explained additional variance. A tendency towards higher Hg concentrations with increasing latitude may be partially related to decreasing growth of char towards the north. However, Hg concentrations in char were positively correlated with growth rates suggesting that Hg concentrations in char also were higher in the more productive study areas, including to the west where mainland riverine inputs of terrestrial carbon, nutrients, and Hg were greater. The data base for assessing time trends in char was limited by the small number of years investigated at most locations, variable fish size across years, small sample size, etc. Where temporal trends were detected, they were of increase on the long term (1970s, 1980s or early 1990s to the present) but of decrease on the short term (early 2000s to present) with Nain (Labrador) showing the converse pattern. Higher Hg concentrations were also related to lower condition factor and cooler springs. Hg concentrations in anadromous char are compared with other terrestrial, aquatic and

Klucel™ EF and ELF polymers for immediate-release oral dosage forms prepared by melt extrusion technology.

Science.gov (United States)

Mohammed, Noorullah Naqvi; Majumdar, Soumyajit; Singh, Abhilasha; Deng, Weibin; Murthy, Narasimha S; Pinto, Elanor; Tewari, Divya; Durig, Thomas; Repka, Michael A

2012-12-01

The objective of this research work was to evaluate Klucel™ hydroxypropylcellulose (HPC) EF and ELF polymers, for solubility enhancement as well as to address some of the disadvantages associated with solid dispersions. Ketoprofen (KPR), a Biopharmaceutics Classification System class II drug with poor solubility, was utilized as a model compound. Preliminary thermal studies were performed to confirm formation of a solid solution/dispersion of KPR in HPC matrix and also to establish processing conditions for hot-melt extrusion. Extrudates pelletized and filled into capsules exhibited a carrier-dependent release with ELF polymer exhibiting a faster release. Tablets compressed from milled extrudates exhibited rapid release owing to the increased surface area of the milled extrudate. Addition of mannitol (MNT) further enhanced the release by forming micro-pores and increasing the porosity of the extrudates. An optimized tablet formulation constituting KPR, MNT, and ELF in a 1:1:1 ratio exhibited 90% release in 15 min similar to a commercial capsule formulation. HPC polymers are non-ionic hydrophilic polymers that undergo polymer-chain-length-dependent solubilization and can be used to enhance solubility or dissolution rate of poorly soluble drugs. Dissolution/release rate could be tailored for rapid-release applications by selecting a suitable HPC polymer and altering the final dosage form. The release obtained from pellets was carrier-dependent and not drug-dependent, and hence, such a system can be effectively utilized to address solubility or precipitation issues with poorly soluble drugs in the gastrointestinal environment.

Resorbable fiber-forming polymers for biotextile applications

CERN Document Server

Gajjar, Chirag R

2014-01-01

This book summarizes the properties and applications of conventional and commercially available fiber-forming, bioresorbable polymers, as well as those currently under study, for use as biotextiles. Factors affecting the performance of these biomaterials are presented, and precautionary measures to reduce premature, hydrolytic degradation during manufacturing and processing are discussed. Because of the structural requirements of medical devices and the technological advancements in synthetic fibers and textile technology, the new field of "Biotextiles" has evolved to exploit the potential of various woven, knitted, braided and non-woven textile structures for biomedical applications. Textile substrates provide certain unique mechanical properties to the medical device and because of an inherently high level of porosity, they can encourage cell growth and promote migration and proliferation. Bioresorbable devices that assist in the repair and regeneration of damaged tissues have in recent years replaced many ...

Effects of Bio-char on Soil Microbes in Herbicide Residual Soils

Directory of Open Access Journals (Sweden)

WANG Gen-lin

2015-10-01

Full Text Available Effects of biological carbon (bio-char on soil microbial community were studied by pot experiments simulating long residual herbicide residues in soil environment, which clarifed the improvement of biochar and its structural properties on soil microenvironment. The results showed that fungi and actinomycetes had the same effect tendency within 0~0.72 mg·kg-1 in clomazone residue which increased the role of stimulation with crop growth process prolonged, especially in high residue treatment, but strong inhibitory effect on bacteria community was occured early which returned to normal until sugar beet growth to fiftieth day. Soil fungi community decreased with bio-char adding, but had no significant difference with the control. When clomazone residue in soil was below 0.24 mg·kg-1, soil actinomycetes community was higher than control without bio-char, bacteria increased first and then reduced after adding carbon as below 0.12 mg·kg-1. Biochar was ‘deep hole’ structure containing C, O, S and other elements. The results showed that a certain concentration clomazone residue in soil would stimulate soil fungi and actinomycetes to grow. After adding the biochar, the inhibition effect of high herbicides residual on bacterial would be alleviated.

Anadromous char as an alternate food choice to marine animals: a synthesis of Hg concentrations, population features and other influencing factors.

Science.gov (United States)

Evans, Marlene S; Muir, Derek C G; Keating, Jonathan; Wang, Xiaowa

2015-03-15

This study was conducted to confirm sporadic measurements made over the late 1970s to the early 1990 s which determined that mercury (Hg) concentrations were low in anadromous char across Arctic and subarctic Canada including northern Québec and Labrador. Over 2004-2013, anadromous char populations across northern Canada were investigated at 20 sites for Hg concentrations and life history characteristics. Hg concentrations were extremely low in anadromous char muscle, typically Hg concentrations over the study area; longitude and latitude also were significant influencing variables. Char length, weight, age, condition factor and lipid content explained additional variance. A tendency towards higher Hg concentrations with increasing latitude may be partially related to decreasing growth of char towards the north. However, Hg concentrations in char were positively correlated with growth rates suggesting that Hg concentrations in char also were higher in the more productive study areas, including to the west where mainland riverine inputs of terrestrial carbon, nutrients, and Hg were greater. The data base for assessing time trends in char was limited by the small number of years investigated at most locations, variable fish size across years, small sample size, etc. Where temporal trends were detected, they were of increase on the long term (1970s, 1980s or early 1990 s to the present) but of decrease on the short term (early 2000s to present) with Nain (Labrador) showing the converse pattern. Higher Hg concentrations were also related to lower condition factor and cooler springs. Hg concentrations in anadromous char are compared with other terrestrial, aquatic and marine vertebrates in traditional diets. The known information on anadromous char is reviewed including population features, habitat, and harvests. Future Hg trend monitoring should focus on specific locations and harvest areas within these areas to better assess trends and influencing factors. Crown

Gasification of brown coal and char with carbon dioxide in the presence of finely dispersed iron catalysts

Energy Technology Data Exchange (ETDEWEB)

Asami, K.; Sears, P.; Furimsky, E.; Ohtsuka, Y. [Osaka City University, Osaka (Japan). Dept. of Applied Chemistry

1996-05-01

Gasification of brown coal and char with CO{sub 2} using iron catalysts precipitated from an aqueous solution of FeCl{sub 3} has been studied. When the pyrolyzed char is gasified in the temperature-programmed mode, the presence of the iron can lower the temperature giving the maximal rate of CO formation by 130-160 K, a larger lowering being observed at a higher loading in the range of {le} 3 wt% Fe. The specific rates of the isothermal gasification iron-bearing chars at 1173 and 1223 K increase with increasing char conversion, resulting in complete gasification within a short reaction time. Comparison of the initial rates of uncatalyzed and catalyzed gasification reveals that iron addition can lower the reaction temperature by 120 K. Moessbauer spectra show that the precipitation iron exists as fine FeOOH particles, which are reduced mainly to Fe{sub 3}C on charring at 1123 K. Most of the Fe{sub 3}C is transformed into {alpha}-Fe and {gamma}-Fe at the initial stage of gasification, and subsequently these species are oxidized to FeO and Fe{sub 3}O{sub 4}. The changes during gasification are discussed in terms of solid-gas and solid-solid reactions. 23 refs., 10 figs.

The mechanism of char ignition in fluidized bed combustors

NARCIS (Netherlands)

Siemons, R.V.

1987-01-01

Knowledge about ignition processes of coal in fluidized beds is of importance for the start-up and dynamic control of these combustors. Initial experiments in a transparent fluidized bed scale model showed the existence of a considerable induction period for the ignition of char, especially at low

Effect of chemical modification on reduction and sorptive properties of chars from hydropyrolysis of coal

Energy Technology Data Exchange (ETDEWEB)

Stanczyk, K.; Miga, K.; Fabis, G.; Jastrzab, K. [Polskiej Akademii Nauk, Gliwice (Poland)

1998-01-01

Hydropyrolysis of bituminous coal and lignite as way of synthesis of adsorbents has been applied. Chemical modification of chars based on simultaneous carbonization of coal and plastics containing sulfur and nitrogen has been carried out. It was stated that modified chars exhibit better reduction and sorptive properties than non-modified and that modified adsorbents made of lignite exceed commercial ones. 7 refs., 4 figs., 3 tabs.

Shape memory polymers

Energy Technology Data Exchange (ETDEWEB)

Wilson, Thomas S.; Bearinger, Jane P.

2017-08-29

New shape memory polymer compositions, methods for synthesizing new shape memory polymers, and apparatus comprising an actuator and a shape memory polymer wherein the shape memory polymer comprises at least a portion of the actuator. A shape memory polymer comprising a polymer composition which physically forms a network structure wherein the polymer composition has shape-memory behavior and can be formed into a permanent primary shape, re-formed into a stable secondary shape, and controllably actuated to recover the permanent primary shape. Polymers have optimal aliphatic network structures due to minimization of dangling chains by using monomers that are symmetrical and that have matching amine and hydroxl groups providing polymers and polymer foams with clarity, tight (narrow temperature range) single transitions, and high shape recovery and recovery force that are especially useful for implanting in the human body.

Shape memory polymers

Science.gov (United States)

Wilson, Thomas S.; Bearinger, Jane P.

2015-06-09

New shape memory polymer compositions, methods for synthesizing new shape memory polymers, and apparatus comprising an actuator and a shape memory polymer wherein the shape memory polymer comprises at least a portion of the actuator. A shape memory polymer comprising a polymer composition which physically forms a network structure wherein the polymer composition has shape-memory behavior and can be formed into a permanent primary shape, re-formed into a stable secondary shape, and controllably actuated to recover the permanent primary shape. Polymers have optimal aliphatic network structures due to minimization of dangling chains by using monomers that are symmetrical and that have matching amine and hydroxyl groups providing polymers and polymer foams with clarity, tight (narrow temperature range) single transitions, and high shape recovery and recovery force that are especially useful for implanting in the human body.

Active carbons from low temperature conversion chars

International Nuclear Information System (INIS)

Adebowale, K.O.; Bayer, E.

2002-05-01

Hulls obtained from the fruits of five tropical biomass have been subjected to low temperature conversion process and their chars activated by partial physical gasification to produce active carbons. The biomass are T. catappa, B. nitida, L leucophylla, D. regia and O. martiana. The bulk densities of the samples ranged from 0.32 g.cm 3 to 0.52 g.cm 3 . Out of the samples T. catappa recorded the highest cellulose content (41.9 g.100g -1 ), while O. martiana contained the highest lignin content (40.7 g.100g -1 ). The ash of the samples were low (0.5 - 4.4%). The percentage of char obtained after conversion were high (33.7% - 38.6%). Active carbons obtained from T. catappa, D. regia and O. martiana, recorded high methylene blue numbers and iodine values. They also displayed good micro- and mesostructural characteristics. Micropore volume (V micro ) was between 0.33cm 3 .g -1 - 0.40cm 3 .g -1 , while the mesopore volume(V meso ) was between 0.05 cm 3 .g -1 - 0.07 cm 3 .g -1 . The BET specific surface exceeds 1000 m 2 .g -1 . All these values compared favourably with high grade commercial active carbons. (author)

Corrosive components of nutshells and their chars

Directory of Open Access Journals (Sweden)

Karczewski Mateusz

2016-01-01

Full Text Available Biomass combustion stands among various technologies pointed at fossil fuels consumption decrease. Biomass can be found in very diversified sources spread more evenly across the globe, can be burned with use of traditional combustion solutions and is more CO2 neutral in combustion than their fossil fuel counterparts. On the other hand biomass has several problems with composition that despite its potential diversity. Problem of excess moisture can be already solved by material selection or by preliminary pyrolysis. The main problem concerns however biomass ash composition. Biomass ashes are more prone to have higher quantities of potentially corrosive components than their coal counterparts. The example of such constituents are alkali metals, sulphur and chlorine. Ash basic composition is also important due to various ash properties like its melting temperature and slagging or fouling tendencies. To address the problem, several indices for fast properties prediction and earlier problem identification can be appointed. This work concentrates on ash quality evaluation for potentially attractive biomass fuel from nutshell materials and their corresponding char obtained by pyrolysis in 300, 450 and 550 °C. Pistachio and hazelnut shells with their chars will be analysed for corrosive compounds and their potential influence on combustion process.

The efficacy of high-throughput sequencing and target enrichment on charred archaeobotanical remains

DEFF Research Database (Denmark)

Nistelberger, H. M.; Smith, O.; Wales, Nathan

2016-01-01

. It has been suggested that high-throughput sequencing (HTS) technologies coupled with DNA enrichment techniques may overcome some of these limitations. Here we report the findings of HTS and target enrichment on four important archaeological crops (barley, grape, maize and rice) performed in three...... lightly-charred maize cob. Even with target enrichment, this sample failed to yield adequate data required to address fundamental questions in archaeology and biology. We further reanalysed part of an existing dataset on charred plant material, and found all purported endogenous DNA sequences were likely...

Synergistic effect on thermal behavior and char morphology analysis during co-pyrolysis of paulownia wood blended with different plastics waste

International Nuclear Information System (INIS)

Chen, Lin; Wang, Shuzhong; Meng, Haiyu; Wu, Zhiqiang; Zhao, Jun

2017-01-01

Highlights: • Positive synergistic effect on volatiles yield during co-pyrolysis of PAW and PP. • Higher char yields than predicated value during PAW/PVC and PAW/PET blends pyrolysis. • Co-pyrolysis of PAW and plastics reduced the mean activation energy of the blends. • The plastics affected the surface morphology of co-pyrolysis chars significantly. - Abstract: Thermal behavior of Paulownia wood (PAW), model plastics (polypropylene, polyvinyl chloride and polyethylene terephthalate, abbreviated as PP, PVC and PET) and their mixtures during pyrolysis process were studied through thermogravimetric analyzer. Scanning electron microscopy technology (SEM) and fractal theory were applied to evaluate the surface morphology of pyrolysis chars. This study found that PP showed synergistic effect on PAW pyrolysis with more volatiles release than predicated value, and the maximum volatiles yield exhibited with 25% PAW blending ratio. However, higher char yields were observed compared with the predicted values during co-pyrolysis process of PAW blends with PVC or PET, and the maximum char yields were obtained under the PAW blending ratio of 75% and 25% respectively. An evident decline in mean activation energy was found during co-pyrolysis of the PAW blending with plastics. The minimum values of mean activation energy for the PAW/PP, PAW/PVC and PAW/PET were gained when the PAW blending ratio were 75%, 50% and 75% respectively. Quantitative information about surface topography of pyrolysis chars were obtained by fractal analysis of the SEM microphotograph. The fractal dimension of residual chars from PAW/PP blends increased from 1.75 to 1.84 as increasing the ratio of PP from 25% to 75%, indicating that PP addition promoted the nonuniformity of the co-pyrolysis chars. The surface morphology of residual chars from PAW/PET and PAW/PVC blends showed a contrary tendency, and the minimum values of fractal dimension were respectively 1.62 and 1.61 under 25% PAW blending

Towards User-Friendly Spelling with an Auditory Brain-Computer Interface: The CharStreamer Paradigm

Science.gov (United States)

Höhne, Johannes; Tangermann, Michael

2014-01-01

Realizing the decoding of brain signals into control commands, brain-computer interfaces (BCI) aim to establish an alternative communication pathway for locked-in patients. In contrast to most visual BCI approaches which use event-related potentials (ERP) of the electroencephalogram, auditory BCI systems are challenged with ERP responses, which are less class-discriminant between attended and unattended stimuli. Furthermore, these auditory approaches have more complex interfaces which imposes a substantial workload on their users. Aiming for a maximally user-friendly spelling interface, this study introduces a novel auditory paradigm: “CharStreamer”. The speller can be used with an instruction as simple as “please attend to what you want to spell”. The stimuli of CharStreamer comprise 30 spoken sounds of letters and actions. As each of them is represented by the sound of itself and not by an artificial substitute, it can be selected in a one-step procedure. The mental mapping effort (sound stimuli to actions) is thus minimized. Usability is further accounted for by an alphabetical stimulus presentation: contrary to random presentation orders, the user can foresee the presentation time of the target letter sound. Healthy, normal hearing users (n = 10) of the CharStreamer paradigm displayed ERP responses that systematically differed between target and non-target sounds. Class-discriminant features, however, varied individually from the typical N1-P2 complex and P3 ERP components found in control conditions with random sequences. To fully exploit the sequential presentation structure of CharStreamer, novel data analysis approaches and classification methods were introduced. The results of online spelling tests showed that a competitive spelling speed can be achieved with CharStreamer. With respect to user rating, it clearly outperforms a control setup with random presentation sequences. PMID:24886978

Sulfur retention by ash during coal combustion. Part I. A model of char particle combustion

Directory of Open Access Journals (Sweden)

BORISLAV GRUBOR

2003-02-01

Full Text Available A model for the combustion of porous char particles as a basis for modeling the process of sulfur retention by ash during coal combustion is developed in this paper. The model belongs to the microscopic intrinsic models and describes the dynamic behavior of a porous char particle during comustion, taking into account temporal and spatial changes of all important physical properties of the char particle and various combustion parameters. The parametric analysis of the enhanced model shows that the model represents a good basis for the development of a model for the process of sulfur retention by ash during coal combustion. The model enables the prediction of the values of all parameters necessary for the introduction of reactions between sulfur compounds and mineral components in ash, primarily calcium oxide.

Nitric oxide reduction in coal combustion: role of char surface complexes in heterogeneous reactions

Energy Technology Data Exchange (ETDEWEB)

Arenillas, A.; Rubiera, F.; Pis, J.J. [Instituto Nacional del Carbon, CSIC, Oviedo (Spain)

2002-12-15

Nitrogen oxides are one of the major environmental problems arising from fossil fuel combustion. Coal char is relatively rich in nitrogen, and so this is an important source of nitrogen oxides during coal combustion. However, due to its carbonaceous nature, char can also reduce NO through heterogeneous reduction. The objectives of this work were on one hand to compare NO emissions from coal combustion in two different types of equipment and on the other hand to study the influence of char surface chemistry on NO reduction. A series of combustion tests were carried out in two different scale devices: a thermogravimetric analyzer coupled to a mass spectrometer and an FTIR (TG-MS-FTIR) and a fluidized bed reactor with on-line battery of analyzers. According to the results obtained, it can be said that the TG-MS-FTIR system provides valuable information about NO heterogeneous reduction and it can give good trends of the behaviour in other combustion equipments, i.e. fluidized bed combustors. It has been also pointed out that NO-char interaction depends to a large extent on temperature. In the low-temperature range NO heterogeneous reduction seems to be controlled by the evolution of surface complexes. In the high-temperature range a different mechanism is involved in NO heterogeneous reduction, the nature of the carbon matrix being a key factor. 27 refs., 6 figs., 1 tab.

Utilization of oil palm tree residues to produce bio-oil and bio-char via pyrolysis

International Nuclear Information System (INIS)

Abnisa, Faisal; Arami-Niya, Arash; Wan Daud, W.M.A.; Sahu, J.N.; Noor, I.M.

2013-01-01

Highlights: • About 14.72% of the total landmass in Malaysia was used for oil palm plantations. • Oil palm tree residues were pyrolyzed to produce bio-oil and bio-char. • The process was performed at a temperature of 500 °C and reaction time of 60 min. • Characterization of the products was performed. - Abstract: Oil palm tree residues are a rich biomass resource in Malaysia, and it is therefore very important that they be utilized for more beneficial purposes, particularly in the context of the development of biofuels. This paper described the possibility of utilizing oil palm tree residues as biofuels by producing bio-oil and bio-char via pyrolysis. The process was performed in a fixed-bed reactor at a temperature of 500 °C, a nitrogen flow rate of 2 L/min and a reaction time of 60 min. The physical and chemical properties of the products, which are important for biofuel testing, were then characterized. The results showed that the yields of the bio-oil and bio-char obtained from different residues varied within the ranges of 16.58–43.50 wt% and 28.63–36.75 wt%, respectively. The variations in the yields resulted from differences in the relative amounts of cellulose, hemicellulose, lignin, volatiles, fixed carbon, and ash in the samples. The energy density of the bio-char was found to be higher than that of the bio-oil. The highest energy density of the bio-char was obtained from a palm leaf sample (23.32 MJ/kg), while that of the bio-oil was obtained from a frond sample (15.41 MJ/kg)

A preliminary high-pressure thermogravimetric study of combustion reactivity of a Collie coal char

Energy Technology Data Exchange (ETDEWEB)

Chan, Yii Leng; Zhang, Zhezi; Zhu, Mingming; Zhang, Dongke [Western Australia Univ., Crawley, WA (Australia). Centre for Energy (M473); Luan, Chao [Western Australia Univ., Crawley, WA (Australia). Centre for Energy (M473); Tsinghua Univ., Beijing (China). Inst. of Thermal Engineering; You, Changfu [Tsinghua Univ., Beijing (China). Inst. of Thermal Engineering

2013-07-01

The effect of pressure(up to 20 bar)on the reactivity of a char(150-160 {mu}m) produced from Western Australian Collie coal has been studied using a high-pressure thermogravimetric analyser (HP TGA). The pressure demonstrated a positive effect in enhancing char combustion reactivities.Kinetic parameters have been determined from the experimental data.The apparent reaction order was found to be approximately 0.7 and the apparent activation energies were 91.0 kJ/mol at atmospheric pressure and 1.5 kJ/mol at an elevated pressure(10 bar),indicating a shift in the control regimes of the reaction at elevated pressures.The lumped effect of the sample size, bulk diffusion,interparticle and intraparticle diffusion at the elevated pressures played an important role in reducing the mass transfer during the HP-TGA experimentation.Thus the activation energy calculated at elevated pressures may not represent the intrinsic activation energy of the char particles but the apparent values of the bulk of the samples.

Bio-oil and bio-char production from corn cobs and stover by fast pyrolysis

International Nuclear Information System (INIS)

Mullen, Charles A.; Boateng, Akwasi A.; Goldberg, Neil M.; Lima, Isabel M.; Laird, David A.; Hicks, Kevin B.

2010-01-01

Bio-oil and bio-char were produced from corn cobs and corn stover (stalks, leaves and husks) by fast pyrolysis using a pilot scale fluidized bed reactor. Yields of 60% (mass/mass) bio-oil (high heating values are ∼20 MJ kg -1 , and densities >1.0 Mg m -3 ) were realized from both corn cobs and from corn stover. The high energy density of bio-oil, ∼20-32 times on a per unit volume basis over the raw corn residues, offers potentially significant savings in transportation costs particularly for a distributed 'farm scale' bio-refinery system. Bio-char yield was 18.9% and 17.0% (mass/mass) from corn cobs and corn stover, respectively. Deploying the bio-char co-product, which contains most of the nutrient minerals from the corn residues, as well as a significant amount of carbon, to the land can enhance soil quality, sequester carbon, and alleviate environmental problems associated with removal of crop residues from fields.

Precursor polymer compositions comprising polybenzimidazole

Science.gov (United States)

Klaehn, John R.; Peterson, Eric S.; Orme, Christopher J.

2015-07-14

Stable, high performance polymer compositions including polybenzimidazole (PBI) and a melamine-formaldehyde polymer, such as methylated, poly(melamine-co-formaldehyde), for forming structures such as films, fibers and bulky structures. The polymer compositions may be formed by combining polybenzimidazole with the melamine-formaldehyde polymer to form a precursor. The polybenzimidazole may be reacted and/or intertwined with the melamine-formaldehyde polymer to form the polymer composition. For example, a stable, free-standing film having a thickness of, for example, between about 5 .mu.m and about 30 .mu.m may be formed from the polymer composition. Such films may be used as gas separation membranes and may be submerged into water for extended periods without crazing and cracking. The polymer composition may also be used as a coating on substrates, such as metal and ceramics, or may be used for spinning fibers. Precursors for forming such polymer compositions are also disclosed.

SYNERGISTIC EFFECTS OF NOVOLAC-BASED CHAR FORMER WITH A PHOSPHORUS/NITROGEN-CONTAINING FLAME RETARDANT IN POLYAMIDE 6

Institute of Scientific and Technical Information of China (English)

Wei-cheng Xiong; Li Chen; De-yi Wang; Fei Song; Yu-zhong Wang

2012-01-01

The synergistic effect of phosphorus oxynitride (PON) with a novolac-based char former modified by salification (NA-metal salt) on the flame retardance of polyamide 6 (PA6) was investigated.For this purpose,various flame-retardant PA6 systems were melt-compounded with PON,PON/NA,PON/NA-V2O5 and PON/NA-Fe2O3,and their flame retardance was evaluated by measuring the limiting oxygen index (LOI) values and UL-94 vertical burning ratings.The results showed that,compared with the PA6/PON/NA system,the combination of two char formers (NA-V2O5,NA-Fe2O3) with PON could obviously improve the char formation and flame retardance of PA6.The flame retardance and cone calorimetric analyses showed the stronger synergism as well as the better flame retardant performance of PON/NA-Fe2O3 flame retardant system.The effects of different char formers on the flame retardance and thermal stability of this system were also discussed.

Cd(II) adsorption on various adsorbents obtained from charred biomaterials

International Nuclear Information System (INIS)

Li Zhenze; Katsumi, Takeshi; Imaizumi, Shigeyoshi; Tang Xiaowu; Inui, Toru

2010-01-01

Cadmium could cause severe toxicant impact to living beings and is especially mobile in the environment. Biomass is abundant and effective to adsorb heavy metals, but is easy to be decomposed biologically which affects the reliability of long-run application. Several biomasses were charred with and without additives at temperatures less than 200 deg. C in this study. The prepared adsorbents were further testified to remove Cd(II) from aqueous solution. Equilibrium and kinetic studies were performed in batch conditions. The effect of several experimental parameters on the cadmium adsorption kinetics namely: contact time, initial cadmium concentration, sorbent dose, initial pH of solution and ionic strength was evaluated. Kinetic study confirmed (1) the rapid adsorption of Cd(II) on GC within 10 min and (2) the following gradual intraparticle diffusion inwards the sorbent at neutral pH and outwards at strong acidic solution. The grass char (GC) was selected for further test according to its high adsorption capacity (115.8 mg g -1 ) and affinity (Langmuir type isotherm). The Cd(II) removal efficiency was increased with increasing solution pH while the highest achieved at sorbent dosage 10.0 g L -1 . The ionic strength affects the sorption of Cd(II) on GC to a limited extent whereas calcium resulted in larger competition to the sorption sites than potassium. Spectroscopic investigation revealed the adsorption mechanisms between Cd(II) and surface functional groups involving amine, carboxyl and iron oxide. The long-term stability of the pyrolyzed grass char and the potential application in engineering practices were discussed.

Active carbons from low temperature conversion chars

Energy Technology Data Exchange (ETDEWEB)

Adebowale, K O [Department of Chemistry, University of lbadan, lbadan (Nigeria); Abdus Salam International Centre for Theoretical Physics, Trieste (Italy); Bayer, E [Universitaet Tuebingen, Institut fuer Organische Chemie, Forschungstelle Nukleinsaeure- und Peptidchemie, Tuebingen (Germany)

2002-05-01

Hulls obtained from the fruits of five tropical biomass have been subjected to low temperature conversion process and their chars activated by partial physical gasification to produce active carbons. The biomass are T. catappa, B. nitida, L leucophylla, D. regia and O. martiana. The bulk densities of the samples ranged from 0.32 g.cm{sup 3} to 0.52 g.cm{sup 3}. Out of the samples T. catappa recorded the highest cellulose content (41.9 g.100g{sup -1}), while O. martiana contained the highest lignin content (40.7 g.100g{sup -1}). The ash of the samples were low (0.5 - 4.4%). The percentage of char obtained after conversion were high (33.7% - 38.6%). Active carbons obtained from T. catappa, D. regia and O. martiana, recorded high methylene blue numbers and iodine values. They also displayed good micro- and mesostructural characteristics. Micropore volume (V{sub micro}) was between 0.33cm{sup 3}.g{sup -1} - 0.40cm{sup 3}.g{sup -1}, while the mesopore volume(V{sub meso}) was between 0.05 cm{sup 3}.g{sup -1} - 0.07 cm{sup 3}.g{sup -1}. The BET specific surface exceeds 1000 m{sup 2}.g{sup -1}. All these values compared favourably with high grade commercial active carbons. (author)

Charring does not affect wood infestation by subterranean termites

Science.gov (United States)

C.J. Peterson; P.D. Gerard; T.L. Wagner

2007-01-01

Fire is an important part of forest ecosystems, as is the insect fauna. Changes in wood brought aboutby fire may alter the ability of termites to use the wood, interrupting the decay cycle of woody debris.The ability of termites to find, infest, and feed upon wood after it had been charred was evaluated in

Structural characteristics and gasification reactivity of chars prepared from K{sub 2}CO{sub 3} mixed HyperCoals and coals

Energy Technology Data Exchange (ETDEWEB)

Atul Sharma; Hiroyuki Kawashima; Ikuo Saito; Toshimasa Takanohashi [National Institute of Advanced Industrial Science and Technology, Ibaraki (Japan). Advanced Fuel Group

2009-04-15

HyperCoal is a clean coal with mineral matter content <0.05 wt %. Oaky Creek (C = 82%), and Pasir (C = 68%) coals were subjected to solvent extraction method to prepare Oaky Creek HyperCoal, and Pasir HyperCoal. Experiments were carried out to compare the gasification reactivity of HyperCoals and parent raw coals with 20, 40, 50 and 60% K{sub 2}CO{sub 3} as a catalyst at 600, 650, 700, and 775{sup o}C with steam. Gasification rates of coals and HyperCoals were strongly influenced by the temperature and catalyst loading. Catalytic steam gasification of HyperCoal chars was found to be chemical reaction controlled in the 600-700{sup o}C temperature range for all catalyst loadings. Gasification rates of HyperCoal chars were found to be always higher than parent coals at any given temperature for all catalyst loadings. However, X-ray diffraction results showed that the microstructures of chars prepared from coals and HyperCoals were similar. Results from nuclear magnetic resonance spectroscopy show no significant difference between the chemical compositions of the chars. Significant differences were observed from scanning electron microscopy images, which showed that the chars from HyperCoals had coral-reef like structures whereas dense chars were observed for coals. 26 refs., 8 figs., 2 tabs.

Textural properties of chars as determined by petrographic analysis: comparison between air-blown, oxygen-blown and oxygen-enriched gasification

CSIR Research Space (South Africa)

Oboirien, BO

2012-11-01

Full Text Available In this study, the textural properties of chars generated from a vitrinite, high ash coal in a fluidised bed gasifier under air-blown, oxygen-blown and oxygen-enriched conditions were determined by detailed petrographic analysis. The char samples...

AUS burnup module CHAR and the associated data pool

International Nuclear Information System (INIS)

Robinson, G.S.

1975-12-01

The CHAR module of the AUS reactor neutronics scheme solves the multiregion nuclide depletion equations using an analytic method. The module obtains cross section, flux and geometry data from AUS data pools, and uses the STATUS data pool which has been designed for the storage of nuclide compositions, spatial smearing factors and other miscellaneous information. (author)

The hierarchical porous structure bio-char assessments produced by co-pyrolysis of municipal sewage sludge and hazelnut shell and Cu(II) adsorption kinetics.

Science.gov (United States)

Zhao, Bing; Xu, Xinyang; Zeng, Fanqiang; Li, Haibo; Chen, Xi

2018-05-04

The co-pyrolysis technology was applied to municipal sewage sludge (MSS) and hazelnut shell with alkaline activating agent K 2 CO 3 under N 2 atmosphere. The innovative bio-char produced by co-pyrolysis had significant physical and chemical characteristics. The specific surface area reached 1990.23 m 2 /g, and the iodine absorption number was 1068.22 mg/g after co-pyrolysis at 850 °C. Although hazelnut shell was a kind of solid waste, it also had abundant cellulose resource, which could contribute to porous structure of bio-char during co-pyrolysis with MSS and decrease total heavy metals contents of raw material to increase security of bio-chars. Meanwhile, the residual fractions of heavy metals in bio-char were above 92.95% after co-pyrolysis at 900 °C except Cd to prevent heavy metals digestion, and the bio-char presented significant immobilization behavior from co-pyrolysis technology. Moreover, the yield and the iodine absorption number of bio-chars under different process variables were analyzed, and it was confirmed that appropriate process variables could contribute the yield and the iodine absorption number of bio-char and prevent to etch pore structure excessively to collapse. The changes of surface functional groups and crystallographic structure before and after co-pyrolysis were analyzed by FTIR and XRD, respectively. The hierarchical porous structure of bio-char was presented by SEM and N 2 adsorption-desorption isotherm. The Cu(II) adsorption capacity of the bio-char was 42.28 mg/g after 24 h, and surface functional groups acted as active binding sites for Cu(II) adsorption. Langmuir model and pseudo-second-order model can describe process of Cu(II) adsorption well.

El Duque de San Pedro de Galatino y la azucarera de Láchar

OpenAIRE

Francisco José Sánchez Sánchez

2015-01-01

El objetivo del trabajo ha sido el estudio de la fábrica azucarera, construida en el año 1890 en la localidad de Láchar (Granada), denominada “Fábrica Conde de Benalúa”, propiedad de Julio Quesada Cañaveral y Piédrola, Señor de Láchar, Conde de Benalúa y de lasVillas, Duque de San Pedro de Galatino y Grande de España. La metodología ha sido posible gracias a la búsqueda de la documentación en los archivos públicos, nacionales, provinciales, locales y privados. Las conclusiones que presentamos...

Bio-oil and bio-char production from corn cobs and stover by fast pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Mullen, Charles A.; Boateng, Akwasi A.; Goldberg, Neil M.; Hicks, Kevin B. [Eastern Regional Research Center, Agricultural Research Service, U.S. Department of Agriculture, 600 E. Mermaid Lane, Wyndmoor, PA 19038 (United States); Lima, Isabel M. [Southern Regional Research Center, Agricultural Research Service, U.S. Department of Agriculture, 1100 Robert E. Lee Blvd., New Orleans, LA 70124 (United States); Laird, David A. [National Soil Tilth Laboratory, U.S. Agricultural Research Service, U.S. Department of Agriculture, 2110 University Blvd., Ames, IA 50011 (United States)

2010-01-15

Bio-oil and bio-char were produced from corn cobs and corn stover (stalks, leaves and husks) by fast pyrolysis using a pilot scale fluidized bed reactor. Yields of 60% (mass/mass) bio-oil (high heating values are {proportional_to}20 MJ kg{sup -1}, and densities >1.0 Mg m{sup -3}) were realized from both corn cobs and from corn stover. The high energy density of bio-oil, {proportional_to}20-32 times on a per unit volume basis over the raw corn residues, offers potentially significant savings in transportation costs particularly for a distributed ''farm scale'' bio-refinery system. Bio-char yield was 18.9% and 17.0% (mass/mass) from corn cobs and corn stover, respectively. Deploying the bio-char co-product, which contains most of the nutrient minerals from the corn residues, as well as a significant amount of carbon, to the land can enhance soil quality, sequester carbon, and alleviate environmental problems associated with removal of crop residues from fields. (author)

A first step towards identification of tannin-derived black carbon: Conventional pyrolysis (Py–GC–MS) and thermally assisted hydrolysis and methylation (THM–GC–MS) of charred condensed tannins

NARCIS (Netherlands)

Kaal, J.; Nierop, K.G.J.; Kraal, P.; Preston, C.M.

2012-01-01

Tannins account for a significant proportion of plant biomass and are likely to contribute to the residues formed by incomplete biomass combustion (black carbon, BC). Nonetheless, the molecular properties of thermally modified tannins have not been investigated in laboratory charring experiments. We

Structural and Compositional Transformations of Biomass Chars during Fast Pyrolysis

DEFF Research Database (Denmark)

Trubetskaya, Anna; Steibel, Markus; Spliethoff, Hartmut

In this work the physical and chemical transformations of biomass chars during fast pyrolysis, considered as a 2nd stage of combustion, has been investigated. Seven biomasses containing different amount of ash and organic components were reacted at up to 1673 K with high heating rates in a wire...

Current status, between-year comparisons and maternal transfer of organohalogenated compounds (OHCs) in Arctic char (Salvelinus alpinus) from Bjørnøya, Svalbard (Norway)

International Nuclear Information System (INIS)

Bytingsvik, J.; Frantzen, M.; Götsch, A.; Heimstad, E.S.; Christensen, G.; Evenset, A.

2015-01-01

High levels of organohalogenated compounds (OHCs) have been found in Arctic char from Lake Ellasjøen at Bjørnøya (Svalbard, Norway) compared to char from other arctic lakes. The first aim of the study was to investigate the OHC status, contaminant profile, and partitioning of OHCs between muscle and ovary tissue in spawning female char from the high-polluted Lake Ellasjøen and the low-polluted Lake Laksvatn. The second aim was to investigate if OHC levels in muscle tissue have changed over time. Between-lake comparisons show that the muscle levels (lipid weight) of hexachlorobenzene (HCB), chlordanes (∑ CHLs), mirex, dichlorodiphenyltrichloroethanes (∑ DDTs) and polychlorinated biphenyls (∑ PCBs) were up to 36 times higher in char from Ellasjøen than in Laksvatn, and confirm that the char from Ellasjøen are still heavily exposed compared to char from neighboring lake. A higher proportion of persistent OHCs were found in Ellasjøen compared to Laksvatn, while the proportion of the less persistent OHCs was highest in Laksvatn. A between-year comparison of OHC levels (i.e., HCB, DDTs, PCBs) in female and male char shows higher levels of HCB in female char from Ellasjøen in 2009/2012 compared to in 1999/2001. No other between-year differences in OHC levels were found. Due to small study groups, findings associated with between-year differences in OHC levels should be interpreted with caution. OHCs accumulate in the lipid rich ovaries of spawning females, resulting in up to six times higher levels of OHCs in ovaries compared to in muscle (wet weight). The toxic equivalent (TEQ)-value for the dioxin-like PCBs (PCB-105 and -118) in ovaries of the Ellasjøen char exceeded levels associated with increased egg mortality in rainbow trout (Oncorhynchus mykiss). Hence, we suggest that future studies should focus on the reproductive health and performance abilities of the high-exposed population of char inhabiting Lake Ellasjøen. - Highlights: • Examine levels

Current status, between-year comparisons and maternal transfer of organohalogenated compounds (OHCs) in Arctic char (Salvelinus alpinus) from Bjørnøya, Svalbard (Norway)

Energy Technology Data Exchange (ETDEWEB)

Bytingsvik, J., E-mail: jenny.bytingsvik@akvaplan.niva.no [Akvaplan-niva AS, The Fram Centre, N-9296 Tromsø Norway (Norway); Frantzen, M. [Akvaplan-niva AS, The Fram Centre, N-9296 Tromsø Norway (Norway); Götsch, A.; Heimstad, E.S. [NILU (Norwegian Institute for Air Research), The Fram Centre, N-9296 Tromsø Norway (Norway); Christensen, G. [Akvaplan-niva AS, The Fram Centre, N-9296 Tromsø Norway (Norway); Evenset, A. [Akvaplan-niva AS, The Fram Centre, N-9296 Tromsø Norway (Norway); University of Tromsø, The Arctic University of Norway, Pb 6050 Langnes, N-9037 Tromsø (Norway)

2015-07-15

High levels of organohalogenated compounds (OHCs) have been found in Arctic char from Lake Ellasjøen at Bjørnøya (Svalbard, Norway) compared to char from other arctic lakes. The first aim of the study was to investigate the OHC status, contaminant profile, and partitioning of OHCs between muscle and ovary tissue in spawning female char from the high-polluted Lake Ellasjøen and the low-polluted Lake Laksvatn. The second aim was to investigate if OHC levels in muscle tissue have changed over time. Between-lake comparisons show that the muscle levels (lipid weight) of hexachlorobenzene (HCB), chlordanes (∑ CHLs), mirex, dichlorodiphenyltrichloroethanes (∑ DDTs) and polychlorinated biphenyls (∑ PCBs) were up to 36 times higher in char from Ellasjøen than in Laksvatn, and confirm that the char from Ellasjøen are still heavily exposed compared to char from neighboring lake. A higher proportion of persistent OHCs were found in Ellasjøen compared to Laksvatn, while the proportion of the less persistent OHCs was highest in Laksvatn. A between-year comparison of OHC levels (i.e., HCB, DDTs, PCBs) in female and male char shows higher levels of HCB in female char from Ellasjøen in 2009/2012 compared to in 1999/2001. No other between-year differences in OHC levels were found. Due to small study groups, findings associated with between-year differences in OHC levels should be interpreted with caution. OHCs accumulate in the lipid rich ovaries of spawning females, resulting in up to six times higher levels of OHCs in ovaries compared to in muscle (wet weight). The toxic equivalent (TEQ)-value for the dioxin-like PCBs (PCB-105 and -118) in ovaries of the Ellasjøen char exceeded levels associated with increased egg mortality in rainbow trout (Oncorhynchus mykiss). Hence, we suggest that future studies should focus on the reproductive health and performance abilities of the high-exposed population of char inhabiting Lake Ellasjøen. - Highlights: • Examine levels

Particle behavior and char burnout mechanisms under pressurized combustion conditions

Energy Technology Data Exchange (ETDEWEB)

Bauer, C.M.; Spliethoff, H.; Hein, K.R.G.

1999-07-01

Combined cycle systems with coal-fired gas turbines promise highest cycle efficiencies for this fuel. Pressurized pulverized coal combustion, in particular, yields high cycle efficiencies due to the high flue gas temperatures possible. The main problem, however, is to ensure a flue gas clean enough to meet the high gas turbine standards with a dirty fuel like coal. On the one hand, a profound knowledge of the basic chemical and physical processes during fuel conversion under elevated pressures is required whereas on the other hand suitable hot gas cleaning systems need to be developed. The objective of this work was to provide experimental data to enable a detailed description of pressurized coal combustion processes. A series of experiments were performed with two German hvb coals, Ensdorf and Goettelborn, and one German brown coal, Garzweiler, using a semi-technical scale pressurized entrained flow reactor. The parameters varied in the experiments were pressure, gas temperature and bulk gas oxygen concentration. A two-color pyrometer was used for in-situ determination of particle surface temperatures and particle sizes. Flue gas composition was measured and solid residue samples taken and subsequently analyzed. The char burnout reaction rates were determinated varying the parameters pressure, gas temperature and initial oxygen concentration. Variation of residence time was achieved by taking the samples at different points along the reaction zone. The most influential parameters on char burnout reaction rates were found to be oxygen partial pressure and fuel volatile content. With increasing pressure the burn-out reactions are accelerated and are mostly controlled by product desorption and pore diffusion being the limiting processes. The char burnout process is enhanced by a higher fuel volatile content.

Adsorption of copper onto char derived macro alga, Undaria pinnatifida

International Nuclear Information System (INIS)

Cho, Hye Jung; Ko, Jeong Huy; Heo, Hyeon Su; Park, Hye Jin; BAe, Yoon Ju; Kim, Jung Hwan; Park, Young-Kwon

2010-01-01

Full text: A release of heavy metals into the environment by industrial activities raises much environmental problems because they tend to remain indefinitely, circulating and eventually accumulating throughout the food chain. Copper is essential to human life and health but, like all heavy metals, is potentially toxic as well. The excessive intakes of copper result in its accumulation in the liver and produce gastrointestinal problems, kidney damage, anemia, and continued inhalation of copper-containing sprays is linked with an increase in lung cancer among exposed people. Consequently, we need to eliminate the copper in drinking water. Also, growth rates of marine macro algae far exceed those of terrestrial biomass, without water limitations, so annual primary production rates are higher for the major marine macro algae than for most terrestrial biomass. According to these reasons, we try to use the macro alga, Undaria pinnatifida. Adsorption of heavy metals is one of the possible technologies involved in the removal of toxic metals from industrial waste streams and mining waste water using low-cost adsorbents. In recent years, many low-cost adsorbents such as seaweeds, activated carbon, etc. have been investigated, but the char by macro alga, Undaria pinnatifida, have not proven to be the most effective and promising substrates. The aim of this study is to remove copper from its aqueous solution by Undaria pinnatifida char for various parameters like pH, contact time, and Cu(II) concentration. The adsorption capacity of Cu(II) by Undaria pinnatifida char was investigated as a function of pH, contact time, and Cu(II) concentration at room temperature. And it was verified using equilibrium studies. (author)

Adsorption of Escherichia coli Using Bone Char | Rezaee | Journal ...

African Journals Online (AJOL)

The aim of study was providing a novel adsorbent for the removal of Escherichia coli (E.coli) as a microbial model from contaminated air especially in hospital units using bone char (BC). The BC was prepared from cattle animal bone by pyrolysis in a furnace at 450°C for 2 h. The characteristics of BC have been determined ...

Triboelectricity: macroscopic charge patterns formed by self-arraying ions on polymer surfaces.

Science.gov (United States)

Burgo, Thiago A L; Ducati, Telma R D; Francisco, Kelly R; Clinckspoor, Karl J; Galembeck, Fernando; Galembeck, Sergio E

2012-05-15

Tribocharged polymers display macroscopically patterned positive and negative domains, verifying the fractal geometry of electrostatic mosaics previously detected by electric probe microscopy. Excess charge on contacting polyethylene (PE) and polytetrafluoroethylene (PTFE) follows the triboelectric series but with one caveat: net charge is the arithmetic sum of patterned positive and negative charges, as opposed to the usual assumption of uniform but opposite signal charging on each surface. Extraction with n-hexane preferentially removes positive charges from PTFE, while 1,1-difluoroethane and ethanol largely remove both positive and negative charges. Using suitable analytical techniques (electron energy-loss spectral imaging, infrared microspectrophotometry and carbonization/colorimetry) and theoretical calculations, the positive species were identified as hydrocarbocations and the negative species were identified as fluorocarbanions. A comprehensive model is presented for PTFE tribocharging with PE: mechanochemical chain homolytic rupture is followed by electron transfer from hydrocarbon free radicals to the more electronegative fluorocarbon radicals. Polymer ions self-assemble according to Flory-Huggins theory, thus forming the experimentally observed macroscopic patterns. These results show that tribocharging can only be understood by considering the complex chemical events triggered by mechanical action, coupled to well-established physicochemical concepts. Patterned polymers can be cut and mounted to make macroscopic electrets and multipoles.

In vitro adsorption of sodium pentobarbital by SuperChar, USP and Darco G-60 activated charcoals

International Nuclear Information System (INIS)

Curd-Sneed, C.D.; Parks, K.S.; Bordelon, J.G.; Stewart, J.J.

1987-01-01

This study was designed to examine the in vitro adsorption of sodium pentobarbital by three activated charcoals. Solutions of sodium pentobarbital (20 mM) were prepared in distilled water and in 70% sorbitol (w/v). Radiolabeled ( 14 C) sodium pentobarbital was added to each solution to serve as a concentration marker. Two ml of each drug solution was added to test tubes containing 40 mg of either Darco G-60, USP, or SuperChar activated charcoal. The drug-charcoal mixtures were incubated at 37 degrees C for O, 2.5, 5, 7.5 or 10 min. Equilibrium, indicated by a constant percentage of drug bound for two consecutive time periods, was established immediately for the aqueous mixtures and for Darco G-60 in sorbitol. The time to equilibrium was prolonged for USP (2.5 min) and SuperChar (5 min) in the presence of sorbitol. In the second series of experiments, solutions of sodium pentobarbital (1.25 to 160 mM) were prepared in either distilled water or sorbitol. Amount of drug bound by 10 to 320 mg of activated charcoal within a 10 min incubation period was determined. Scatchard analysis determined maximum binding capacity (Bmax) and dissociation constants (Kd) for each activated charcoal. In water, Bmax (mumoles/gm) was greatest for SuperChar (1141), followed by USP (580) and Darco G-60 (381), while the Kd's did not differ. Sorbitol did not change the Bmax or Kd of USP or Darco G-60, but the additive significantly decreased the Bmax (717) and increased the Kd for SuperChar (3.3 to 10.1 mM). The results suggest that relative binding capacity of activated charcoal is directly proportional to surface area, and that sorbitol significantly reduces sodium pentobarbital binding to SuperChar

CharToon 2.1 extensions : expression repertoire and lip sync

NARCIS (Netherlands)

Z.M. Ruttkay; A.D.F. Lelièvre (Alban)

2000-01-01

textabstractCharToon is a modular system to design and animate 21/2D faces and other graphic al objects. This report contains the extensions made for version 2.1, effecting only the Animation Editor module. The new features allow the re-usage of a reper toire of expression snapshots and animations

Characterization of red mud-epoxy intumescent char using surface imaging and micro analysis

Energy Technology Data Exchange (ETDEWEB)

Arogundade, A. I., E-mail: ajiunolorioba@gmail.com; Megat-Yusoff, P. S. M., E-mail: puteris@petronas.com.my; Faiz, A. [Department of Mechanical Engineering, Universiti Tecknologi Petronas (Malaysia); Bhat, A. H. [Department of Fundamental and Applied Science, Universiti Tecknologi Petronas (Malaysia)

2015-07-22

In this study, red mud (RM), an oxide waste was proposed as reinforcing, synergistic filler for the traditional epoxy intumescent coating (IC). 5.5 wt% of acid-modified and unmodified red mud were introduced into the basic intumescent formulation of ammonium polyphosphate (APP), pentaerythritol (PER) and melamine (MEL). In order to predict effect of modification on its suitability, Field emission electron scanning microscopy and Fourier transform infra red were used to obtain detailed characteristics such as the cell size, pore distribution, homogeneity and chemical composition of the red mud-epoxy carbonaceous char. Both acid-modified and unmodified RM-filled ICs produced chars with smaller and more closely packed cells compared to chars from the unfilled coating. Both coating types had hard carbonaceous metal phosphate coverings that could act as heat barriers. The unmodified red mud was found to be antagonistic to the intumescent action with an expansion of only 2 times the initial thickness. The leached, low iron-red mud produced an expansion of 15 times the initial thickness, but possessed a hollow interior. From these findings, it may be deduced that while acid leaching of red mud may improve intumescent expansion, it would be necessary to optimize the percent filler loading to improve residual mass.

Pyrolysis of waste animal fats in a fixed-bed reactor: Production and characterization of bio-oil and bio-char

Energy Technology Data Exchange (ETDEWEB)

Ben Hassen-Trabelsi, A., E-mail: aidabenhassen@yahoo.fr [Centre de Recherche et de Technologies de l’Energie (CRTEn), Technopôle Borj-Cédria, B.P 95, 2050, Hammam Lif (Tunisia); Kraiem, T. [Centre de Recherche et de Technologies de l’Energie (CRTEn), Technopôle Borj-Cédria, B.P 95, 2050, Hammam Lif (Tunisia); Département de Géologie, Université de Tunis, 2092, Tunis (Tunisia); Naoui, S. [Centre de Recherche et de Technologies de l’Energie (CRTEn), Technopôle Borj-Cédria, B.P 95, 2050, Hammam Lif (Tunisia); Belayouni, H. [Département de Géologie, Université de Tunis, 2092, Tunis (Tunisia)

2014-01-15

Highlights: • Produced bio-fuels (bio-oil and bio-char) from some animal fatty wastes. • Investigated the effects of main parameters on pyrolysis products distribution. • Determined the suitable conditions for the production of the maximum of bio-oil. • Characterized bio-oils and bio-chars obtained from several animal fatty wastes. - Abstract: Several animal (lamb, poultry and swine) fatty wastes were pyrolyzed under nitrogen, in a laboratory scale fixed-bed reactor and the main products (liquid bio-oil, solid bio-char and syngas) were obtained. The purpose of this study is to produce and characterize bio-oil and bio-char obtained from pyrolysis of animal fatty wastes. The maximum production of bio-oil was achieved at a pyrolysis temperature of 500 °C and a heating rate of 5 °C/min. The chemical (GC–MS analyses) and spectroscopic analyses (FTIR analyses) of bio-oil showed that it is a complex mixture consisting of different classes of organic compounds, i.e., hydrocarbons (alkanes, alkenes, cyclic compounds…etc.), carboxylic acids, aldehydes, ketones, esters,…etc. According to fuel properties, produced bio-oils showed good properties, suitable for its use as an engine fuel or as a potential source for synthetic fuels and chemical feedstock. Obtained bio-chars had low carbon content and high ash content which make them unattractive for as renewable source energy.

Pyrolysis of waste animal fats in a fixed-bed reactor: Production and characterization of bio-oil and bio-char

International Nuclear Information System (INIS)

Ben Hassen-Trabelsi, A.; Kraiem, T.; Naoui, S.; Belayouni, H.

2014-01-01

Highlights: • Produced bio-fuels (bio-oil and bio-char) from some animal fatty wastes. • Investigated the effects of main parameters on pyrolysis products distribution. • Determined the suitable conditions for the production of the maximum of bio-oil. • Characterized bio-oils and bio-chars obtained from several animal fatty wastes. - Abstract: Several animal (lamb, poultry and swine) fatty wastes were pyrolyzed under nitrogen, in a laboratory scale fixed-bed reactor and the main products (liquid bio-oil, solid bio-char and syngas) were obtained. The purpose of this study is to produce and characterize bio-oil and bio-char obtained from pyrolysis of animal fatty wastes. The maximum production of bio-oil was achieved at a pyrolysis temperature of 500 °C and a heating rate of 5 °C/min. The chemical (GC–MS analyses) and spectroscopic analyses (FTIR analyses) of bio-oil showed that it is a complex mixture consisting of different classes of organic compounds, i.e., hydrocarbons (alkanes, alkenes, cyclic compounds…etc.), carboxylic acids, aldehydes, ketones, esters,…etc. According to fuel properties, produced bio-oils showed good properties, suitable for its use as an engine fuel or as a potential source for synthetic fuels and chemical feedstock. Obtained bio-chars had low carbon content and high ash content which make them unattractive for as renewable source energy

Coal devolatilization and char conversion under suspension fired conditions in O2/N2 and O2/CO2 atmospheres

DEFF Research Database (Denmark)

Jensen, Anker Degn; Brix, Jacob; Jensen, Peter Arendt

2010-01-01

have been carried out in an electrically heated entrained flow reactor that is designed to simulate the conditions in a suspension fired boiler. Coal devolatilized in N2 and CO2 atmospheres provided similar results regarding char morphology, char N2-BET surface area and volatile yield. This strongly......The aim of the present investigation is to examine differences between O2/N2 and O2/CO2 atmospheres during devolatilization and char conversion of a bituminous coal at conditions covering temperatures between 1173 K and 1673 K and inlet oxygen concentrations between 5 and 28 vol.%. The experiments...

Surface characterisation of synthetic coal chars made from model compounds

Energy Technology Data Exchange (ETDEWEB)

Arenillas, A.; Pevida, C.; Rubiera, F.; Palacios, J.M.; Navarrete, R.; Denoyel, R.; Rouquerol, J.; Pis, J.J. [Instituto Nacional del Carbon, CSIC, Oviedo (Spain)

2004-07-01

Knowledge of surface properties is essential for understanding the reaction mechanisms involved in several coal conversion processes. However, due to the complexity and heterogeneity of coal this is rather difficult and the use of known model compounds could be a valuable tool. Single model compounds have been widely used, but they give a quite simplified picture. In this work a mixture of model compounds in a phenol-formaldehyde matrix was cured in order to create cross-linked structures. The obtained synthetic coal was pyrolysed in a fixed bed reactor, under helium atmosphere. The surface composition of the chars was evaluated by XPS, adsorption gravimetry of water vapour, temperature-programmed desorption and potentiometric titration. Texture was characterised by N{sub 2} and CO{sub 2} adsorption isotherms at 77 and 273 K, respectively, and immersion calorimetry in benzene. The results obtained from the different techniques were contrasted in order to give an overview of the surface properties (chemical and physical) of the samples studied. Chars obtained under the same operating conditions from a high volatile bituminous coal were used as a reference.

ADSORPTION OF MANGANESE FROM ACID MINE DRAINAGE EFFLUENTS USING BONE CHAR: CONTINUOUS FIXED BED COLUMN AND BATCH DESORPTION STUDIES

Directory of Open Access Journals (Sweden)

D. C. Sicupira

2015-06-01

Full Text Available AbstractIn the present study, continuous fixed bed column runs were carried out in an attempt to evaluate the feasibility of using bone char for the removal of manganese from acid mine drainage (AMD. Tests using a laboratory solution of pure manganese at typical concentration levels were also performed for comparison purposes. The following operating variables were evaluated: column height, flow rate, and initial pH. Significant variations in resistance to the mass transfer of manganese into the bone char were identified using the Thomas model. A significant effect of the bed height could only be observed in tests using the laboratory solution. No significant change in the breakthrough volume could be observed with different flow rates. By increasing the initial pH from 2.96 to 5.50, the breakthrough volume was also increased. The maximum manganese loading capacity in continuous tests using bone char for AMD effluents was 6.03 mg g-1, as compared to 26.74 mg g-1 when using the laboratory solution. The present study also performed desorption tests, using solutions of HCl, H2SO4, and water, aimed at the reuse of the adsorbent; however, no promising results were obtained due to low desorption levels associated with a relatively high mass loss. Despite the desorption results, the removal of manganese from AMD effluents using bone char as an adsorbent is technically feasible and attends to environmental legislation. It is interesting to note that the use of bone char for manganese removal may avoid the need for pH corrections of effluents after treatment. Moreover, bone char can also serve to remove fluoride ions and other metals, thus representing an interesting alternative material for the treatment of AMD effluents.

Adsorption of heavy metal ions from aqueous solutions by bio-char, a by-product of pyrolysis

International Nuclear Information System (INIS)

Kılıç, Murat; Kırbıyık, Çisem; Çepelioğullar, Özge; Pütün, Ayşe E.

2013-01-01

Bio-char, a by-product of almond shell pyrolysis, was used as an alternative adsorbent precursor for the removal of heavy metal ions from aqueous solutions. The adsorption potential of almond shell bio-char for Ni(II) and Co(II) removal was investigated. Adsorption experiments were carried out by varying pH, adsorbent dosage, initial metal ion concentrations, contact time and temperature to determine the optimum conditions. To describe the equilibrium isotherms the experimental data were analyzed by the Langmuir, Freundlich, Dubinin–Radushkevich (D–R) and Temkin isotherm models. Pseudo-first order, pseudo-second order, and intraparticle diffusion kinetic models were used to find out the kinetic parameters and mechanism of adsorption process. The thermodynamic parameters such as ΔG°, ΔH° and ΔS° were calculated for predicting the nature of adsorption. The results showed that bio-char derived from pyrolysis of biomass can be used as a low-cost and effective adsorbent for removal of heavy metal ions from aqueous solutions.

Influence of potassium hydroxide activation on characteristics and environmental risk of heavy metals in chars derived from municipal sewage sludge.

Science.gov (United States)

Li, Zhengjia; Deng, Hui; Yang, Le; Zhang, Genlin; Li, Yuqi; Ren, Yansen

2018-05-01

To investigate the influence of KOH activation on characteristics and environmental risk of heavy metals in chars, sludge was pyrolyzed with varying amount of KOH. The analyzation of characteristics and potential ecological risk evaluation of heavy metals were conducted by surface area analyzer, FTIR, XRD and BCR sequential extraction. The activated chars have higher surface area and lower content of silica compared to those without being activated. The activation of KOH promoted residual fraction of Cd, meanwhile, Zinc, Cr, Ni and Mn were converted to relatively unstable fractions (F2 and F3). The results of risk assessment indicated that the potential ecological risk level of Cd was reduced in activated chars, while risk level of Zn, Cr, Ni and Mn were increased after pyrolysis with KOH activation. The potential ecological risk of heavy metals in activated chars was further declined, and the risk level transformed from moderate to low. Copyright © 2018 Elsevier Ltd. All rights reserved.

Supramolecular coordination polymer formed from artificial light-harvesting dendrimer.

Science.gov (United States)

Lee, Hosoowi; Jeong, Young-Hwan; Kim, Joo-Ho; Kim, Inhye; Lee, Eunji; Jang, Woo-Dong

2015-09-30

We report the formation of supramolecular coordination polymers formed from multiporphyrin dendrimers (PZnPM; M = FB or Cu), composed of the focal freebase porphyrin (PFB) or cupper porphyrin (PCu) with eight zinc porphyrin (PZn) wings, and multipyridyl porphyrins (PyPM; M = FB or Cu), PFB or PCu with eight pyridyl groups, through multiple axial coordination interactions of pyridyl groups to PZns. UV-vis absorption spectra were recorded upon titration of PyPFB to PZnPFB. Differential spectra, obtained by subtracting the absorption of PZnPFB without guest addition as well as the absorption of PyPFB, exhibited clear isosbestic points with saturation binding at 1 equiv addition of PyPFB to PZnPFB. Job's plot analysis also indicated 1:1 stoichiometry for the saturation binding. The apparent association constant between PZnPFB and PyPFB (2.91 × 10(6) M(-1)), estimated by isothermal titration calorimetry, was high enough for fibrous assemblies to form at micromolar concentrations. The formation of a fibrous assembly from PZnPFB and PyPFB was visualized by atomic force microscopy and transmission electron microscopy (TEM). When a 1:1 mixture solution of PZnPFB and PyPFB (20 μM) in toluene was cast onto mica, fibrous assemblies with regular height (ca. 2 nm) were observed. TEM images obtained from 1:1 mixture solution of PZnPFB and PyPFB (0.1 wt %) in toluene clearly showed the formation of nanofibers with a regular diameter of ca. 6 nm. Fluorescence emission measurement of PZnPM indicated efficient intramolecular energy transfer from PZn to the focal PFB or PCu. By the formation of supramolecular coordination polymers, the intramolecular energy transfer changed to intermolecular energy transfer from PZnPM to PyPM. When the nonfluorescent PyPCu was titrated to fluorescent PZnPFB, fluorescence emission from the focal PFB was gradually decreased. By the titration of fluorescent PyPFB to nonfluorescent PZnPCu, fluorescence emission from PFB in PyPFB was gradually increased

SiteChar – Methodology for a Fit-for-Purpose Assessment of CO2 Storage Sites in Europe

Directory of Open Access Journals (Sweden)

Delprat-Jannaud F.

2015-04-01

Full Text Available The FP7-funded SiteChar project examined the entire CO2 geological storage site characterisation process, from the initial feasibility studies through to the final stage of application for a CO2 storage permit based on criteria defined by the relevant European legislation. The SiteChar workflow for CO2 geological storage site characterisation provides a description of all elements of a site characterisation study, as well as guidance to streamline the site characterisation process and make sure that the output covers the aspects mentioned in the European Community (EC Storage Directive. Five potential European storage sites, representative of prospective geological contexts, were considered as test sites for the research work: a North Sea multi-store site (hydrocarbon field and aquifer offshore Scotland; an onshore aquifer in Denmark; an onshore gas field in Poland; an aquifer offshore in Norway; and an aquifer in the Southern Adriatic Sea. This portfolio combines complementary sites that allowed to encompass the different steps of the characterisation workflow. A key innovation was the development of internal ‘dry-run’ permit applications at the Danish and Scottish sites and their review by relevant regulatory authorities. This process helped to refine the site characterisation workflow, and aimed to identify remaining gaps in site-specific characterisation, needed to secure storage permits under the EC Storage Directive as implemented in ‘host’ Member States. SiteChar considered the important aspect of the public awareness and public opinions of these new technologies, in parallel to technical issues, on the onshore Polish and offshore Scottish sites. A new format to assist public opinion-forming processes was tested involving a small sample of local communities. Generic as well as site-specific information was made available to the general and local public via the internet and at information meetings. These exercises provide insight

Volatiles and char combustion rates of demineralised lignite and wood blends

International Nuclear Information System (INIS)

Yilgin, Melek; Pehlivan, Dursun

2009-01-01

Today, much interest is given to the utilisation of materials of plant origin as substitutions of fossil fuels in meeting energy needs to reduce the level of atmospheric pollutant emissions and global warming threat, and emphasis has been placed on the co-combustion of coal and biomass. In this study, volatiles and char combustion behaviour of the fuel pellets composed from demineralised lignite and poplar wood sawdust, were investigated in a cylindrical wire mesh basket placed in a preheated tube furnace. The results have shown that ignition times of the pellets decreased with the burning temperature and shortened further due to demineralisation of lignite. Volatiles combustion rates of the samples did not correlate well with combustion times. However, they can be correlated with their respective proximate volatile matter contents. Char burnout times decreased with increasing combustion rates and correlated well with the respective proximate fixed carbon contents of the samples. Deviations were more considerable in the case of rate data. (author)

Synthesis, Amphiphilic Property and Thermal Stability of Novel Main-chain Poly(o-carborane-benzoxazines)

Science.gov (United States)

Yang, Xiaoxue; Han, Guo; Yang, Zhen; Zhang, Xiaoa; Jiang, Shengling; Lyu, Yafei

2017-10-01

Five poly(o-carborane-benzoxazines) were synthesized via Mannich reaction of o-carborane bisphenol, paraformaldehyde, and diamine, and their structures were well characterized. Light transmission and 1H NMR in D2O confirmed that poly(o-carborane-benzoxazines) with PEG segments showed excellent water solubility and amphiphilic property. TGA analyses were conducted under nitrogen and air, and the results showed that the polymers own high initial decomposition temperatures owing to the shielding effect of carborane moiety on its adjacent aromatic structures. Besides, poly(o-carborane-benzoxazines) own high char yield at elevated temperatures, for the boron atom could combine with oxygen from the polymer structure or/and the air and be oxidized to form boron oxide, and thus the polymer weight is retained to a large extent. PEG segments had an adverse effect on the initial decomposition and char yield, and thus their concentration should be adjusted to control the polymer’s thermal stability.

A Study on the Applicability of Kinetic Models for Shenfu Coal Char Gasification with CO2 at Elevated Temperatures

Directory of Open Access Journals (Sweden)

Jinsheng Gao

2009-07-01

Full Text Available In this paper, measurements of the CO2 gasification kinetics for two types of Shenfu coal chars, which were respectively prepared by slow and rapid pyrolysis at temperatures of 950 °C and 1,400 °C, were performed by an isothermal thermo-gravimetric analysis under ambient pressure and elevated temperature conditions. Simultaneously, the applicability of the kinetic model for the CO2 gasification reaction of Shenfu coal chars was discussed. The results showed: (i the shrinking un-reacted core model was not appropriate to describe the gasification reaction process of Shenfu coal chars with CO2 in the whole experimental temperature range; (ii at the relatively low temperatures, the modified volumetric model was as good as the random pore model to simulate the CO2 gasification reaction of Shenfu coal chars, while at the elevated temperatures, the modified volumetric model was superior to the random pore model for this process; (iii the integral expression of the modified volumetric model was more favorable than the differential expression of that for fitting the experimental data. Moreover, by simply introducing a function: A = A★exp(ft, it was found that the extensive model of the modified volumetric model could make much better predictions than the modified volumetric model. It was recommended as a convenient empirical model for comprehensive simulation of Shenfu coal char gasification with under conditions close to those of entrained flow gasification.

Fasting augments PCB impact on liver metabolism in anadromous Arctic Char

Science.gov (United States)

Vijayan, M.M.; Aluru, N.; Maule, A.G.; Jorgensen, E.H.

2006-01-01

Anadromous arctic char (Salvelinus alpinus) undertake short feeding migrations to seawater every summer and accumulate lipids, while the rest of the year is spent in fresh water where the accumulated lipid reserves are mobilized. We tested the hypothesis that winter fasting and the associated polychlorinated biphenyls' (PCBs) redistribution from lipid depots to critical tissues impair the liver metabolic capacity in these animals. Char were administered Aroclor 1254 (0, 1, 10, and 100 mg/ kg body mass) orally and maintained for 4 months without feeding to mimic seasonal winter fasting, while fed groups (0 and 100 mg Aroclor 1254/kg) were maintained for comparison. A clear dose-related increase in PCB accumulation and cytochrome P4501A (CYP1A) protein content was observed in the livers of fasted fish. This PCB concentration and CYP1A response with the high dose of Aroclor were 1.5-fold and 3-fold greater in the fasted than in the fed fish, respectively. In fed fish, PCB exposure lowered liver glycogen content, whereas none of the other metabolic indicators were significantly affected. In fasted fish, PCB exposure depressed liver glycogen content and activities of glucose-6-phosphate dehydrogenase, alanine aminotransferase, lactate dehydrogenase, and phosphoenolpyruvate carboxykinase and elevated 3-hydroxyacylcoA dehydrogenase activity and glucocorticoid receptor protein expression. There were no significant impacts of PCB on heat shock protein 70 (hsp70) and hsp90 contents in either fed or fasted fish. Collectively, our study demonstrates that winter emaciation associated with the anadromous lifestyle predisposes arctic char to PCB impact on hepatic metabolism including disruption of the adaptive metabolic responses to extended fasting. ?? 2006 Oxford University Press.

Adsorption of heavy metals by bio-chars produced from pyrolysis of paper mulberry from simulated industrial wastewater

International Nuclear Information System (INIS)

Adil, S.; Asma, M.

2014-01-01

Paper mulberry bio-char (by-product of pyrolysis) was evaluated for the removal of heavy metals (Cd, Cr, Cu, Zn and Pb) from simulated industrial waste water. The surface properties and surface area of the bio-char was found suitable for metal adsorption. Batch sorption studies for adsorption potential of paper mulberry bio-char for Cd, Cr, Cu, Pb and Zn were investigated under different experimental conditions of pH, temperature and contact time. Maximum removal efficiency of Cd, Cu, Pb and Zn was 97.8, 76.8, 85.6, and 82.2 % respectively at pH 12 while maximum removal of Cr was recorded (98%) at pH 2. The removal efficiency showed different behaviour at different contact times. Maximum removal efficiency of Cd, Cr, Zn was 81, 86, 61.4% at contact time of 3 hr. The maximum removal of Cu was 64.2% observed at a contact time of 4 hours while the maximum removal of Pb and Zn was 85% at contact time of 2 hr. The values of the thermodynamic parameters, enthalpy delta H, Gibbs free energy delta G of sorption and entropy delta So were calculated to define endothermic or exothermic behavior of the sorbent used. Negative value of delta G for Cd, Cu, Cr and Pb indicated paper mulberry bio-char as a feasible sorbent for the efficient removal of Cd, Cu, Cr and Pb. Negative value of delta H was observed for Cd and Pb indicating that the adsorption process is exothermic while positive value of delta H was calculated for Cu, Cr and Zn showed that the adsorption is endothermic. The results obtained showed that plant residue bio-char can act as an effective sorbent for the removal of heavy metals from aqueous solutions. (author)

Flame-Retardant and Thermal Degradation Mechanism of Caged Phosphate Charring Agent with Melamine Pyrophosphate for Polypropylene

Directory of Open Access Journals (Sweden)

Xuejun Lai

2015-01-01

Full Text Available An efficient caged phosphate charring agent named PEPA was synthesized and combined with melamine pyrophosphate (MPP to flame-retard polypropylene (PP. The effects of MPP/PEPA on the flame retardancy and thermal degradation of PP were investigated by limiting oxygen index (LOI, vertical burning test (UL-94, cone calorimetric test (CCT, and thermogravimetric analysis (TGA. It was found that PEPA showed an outstanding synergistic effect with MPP in flame retardant PP. When the content of PEPA was 13.3 wt% and MPP was 6.7 wt%, the LOI value of the flame retardant PP was 33.0% and the UL-94 test was classed as a V-0 rating. Meanwhile, the peak heat release rate (PHRR, average heat release rate (AV-HRR, and average mass loss rate (AV-MLR of the mixture were significantly reduced. The flame-retardant and thermal degradation mechanism of MPP/PEPA was investigated by TGA, Fourier transform infrared spectroscopy (FTIR, TG-FTIR, and scanning electron microscopy-energy dispersive X-ray spectrometry (SEM-EDXS. It revealed that MPP/PEPA could generate the triazine oligomer and phosphorus-containing compound radicals which changed the thermal degradation behavior of PP. Meanwhile, a compact and thermostable intumescent char was formed and covered on the matrix surface to prevent PP from degrading and burning.

Basic study of charring detection at the laser catheter-tip using back scattering light measurement during therapeutic laser irradiation in blood.

Science.gov (United States)

Takahashi, Mei; Ito, Arisa; Kajihara, Takuro; Matsuo, Hiroki; Arai, Tsunenori

2010-01-01

The purpose of this study is to investigate transient process of the charring at the laser catheter-tip in blood during therapeutic laser irradiation by the back scattering light measurement to detect precursor state of the charring. We took account of using photodynamic therapy for arrhythmia in blood through the laser catheter. We observed the influence of the red laser irradiation (λ=663 nm) upon the shape of red blood cells (RBCs). The RBCs aggregation, round formation, and hemolysis were took place sequentially before charring. With a model blood sandwiched between glass plates simulated as a catheter-tip boundary, we measured diffuse-reflected-light power and transmitted-light power simultaneously and continuously by a microscopic optics during the laser irradiation. We found that measured light power changes were originated with RBCs shape change induced by temperature rise due to the laser irradiation. A gentle peak following a slow descending was observed in the diffuse-reflected-light power history. This history might indicate the precursor state of the charring, in which the hemolysis might be considered to advance rapidly. We think that the measurement of diffuse-reflected-light power history might be able to detect precursor state of charring at the catheter-tip in blood.

Carbon conversion predictor for fluidized bed gasification of biomass fuels - from TGA measurements to char gasification particle model

Energy Technology Data Exchange (ETDEWEB)

Konttinen, J.T. [University of Jyvaeskylae, Department of Chemistry, Renewable Energy Programme, POB 35, Jyvaeskylae (Finland); Moilanen, A. [VTT Technical Research Centre of Finland, POB 1000, Espoo (Finland); Martini, N. de; Hupa, M. [Abo Akademi University, Process Chemistry Centre, Combustion and Materials Chemistry, Turku (Finland)

2012-09-15

When a solid fuel particle is injected into a hot fluidized bed, the reactivity of fuel char in gasification reactions (between char carbon and steam and CO{sub 2}) plays a significant role for reaching a good carbon conversion. In this paper, the gasification reactivity data of some solid waste recovered fuels (SRF) obtained from thermogravimetric analysis (TGA) experiments is presented. Gas mixtures (H{sub 2}O, H{sub 2}, CO{sub 2}, CO), were used in the experiments to find the inhibitive effects of CO and H{sub 2}. Average char gasification reactivity values are determined from the TGA results. Kinetic parameters for char carbon gasification reactivity correlations are determined from this data. The Uniform Conversion model is used to account for the change of gasification reaction rate as function of carbon conversion. Some discrepancies, due to complicated ash-carbon interactions, are subjects of further research. In the carbon conversion predictor, laboratory measured reactivity numbers are converted into carbon conversion numbers in a real-scale fluidized bed gasifier. The predictor is a relatively simple and transparent tool for the comparison of the gasification reactivity of different fuels in fluidized bed gasification. The residence times for solid fuels in fluidized bed gasifiers are simulated. Simulations against some pilot-scale results show reasonable agreement. (orig.)

Development of an advanced continuous mild gasification process for the production of coproducts. Task 4, System integration studies: Char upgrading

Energy Technology Data Exchange (ETDEWEB)

Jha, M.C.; McCormick, R.L.; Hogsett, R.F.; Rowe, R.M.; Anast, K.R.

1991-12-01

This document describes the results of Task 4 under which a 50 pound/hour char-to-carbon (CTC) process research unit (PRU) was designed in the second half of 1989, with construction completed in June 1990. The CTC PRU at Golden was operated for nearly one year during which 35 runs were completed for a total of nearly 800 hours of operation. Char methanation and carbon production reactor development activities are detailed in this report, as well as the results of integrated runs of the CTC process. Evaluation of the process and the carbon product produced is also included. It was concluded that carbon could be produced from mild gasification char utilizing the CTC process. Char methanation and membrane separation steps performed reasonably well and can scaled up with confidence. However, the novel directly heated reactor system for methane cracking did not work satisfactorily due to materials of construction and heat transfer problems, which adversely affected the quantity and quality of the carbon product. Alternative reactor designs are recommended.

Valorization of algal waste via pyrolysis in a fixed-bed reactor: Production and characterization of bio-oil and bio-char.

Science.gov (United States)

Aboulkas, A; Hammani, H; El Achaby, M; Bilal, E; Barakat, A; El Harfi, K

2017-11-01

The aim of the present work is to develop processes for the production of bio-oil and bio-char from algae waste using the pyrolysis at controlled conditions. The pyrolysis was carried out at different temperatures 400-600°C and different heating rates 5-50°C/min. The algal waste, bio-oil and bio-char were successfully characterized using Elemental analysis, Chemical composition, TGA, FTIR, 1 H NMR, GC-MS and SEM. At a temperature of 500°C and a heating rate of 10°C/min, the maximum yield of bio-oil and bio-char was found to be 24.10 and 44.01wt%, respectively, which was found to be strongly influenced by the temperature variation, and weakly affected by the heating rate variation. Results show that the bio-oil cannot be used as bio-fuel, but can be used as a source of value-added chemicals. On the other hand, the bio-char is a promising candidate for solid fuel applications and for the production of carbon materials. Copyright © 2017 Elsevier Ltd. All rights reserved.

Biostable glucose permeable polymer

DEFF Research Database (Denmark)

2017-01-01

A new biostable glucose permeable polymer has been developed which is useful, for example, in implantable glucose sensors. This biostable glucose permeable polymer has a number of advantageous characteristics and, for example, does not undergo hydrolytic cleavage and degradation, thereby providing...... a composition that facilitates long term sensor stability in vivo. The versatile characteristics of this polymer allow it to be used in a variety of contexts, for example to form the body of an implantable glucose sensor. The invention includes the polymer composition, sensor systems formed from this polymer...

The application of carbon isotope discrimination of charred wheat grains to reconstruct Late Holocene climate change and identify water management strategy in northwest China

Science.gov (United States)

Wang, W.; An, C.; Duan, F.; Zhao, Y.; Cao, Z.

2017-12-01

The AMS 14C dating and corresponding carbon stable isotope datum of charred wheat grains from archaeological sites in northwest China especially Hexi Corridor and Xinjiang have been collected widely to study its potential roles in reconstructing past climate change and identifying water management strategies through comparison with integrated regional humidity index, carbon isotope data of wheat grown under modern irrigation environment from study area and Mediterranean charred wheat carbon isotope data. The results suggest (1) carbon isotope discrimination values of charred wheat both in Hexi corridor and Xinjiang could respond well to regional moisture change, and there are also good positive correlation relationship between them (2) in contrast to consistent relationship between decreased carbon isotope discrimination values of charred wheat and dry climate condition, increased carbon isotope discrimination values does not represent wetter regional climate completely and may also reveal effects of human irrigation activities. The higher carbon isotope discrimination value of charred wheat which occurred in the Hexi Corridor from 4000 to 3850 a BP, 2100 a BP and 550 a BP and in Tianshan area of Xinjiang from 3730 a BP could be likely to be related with human activities (3) the carbon isotope discrimination value of charred wheat may have a certain limit which is generally not beyond 19‰. And this upper limit could influence its availability in reflecting abrupt change of precipitation/humidity especially rapid wetter trend. We conclude that carbon isotope analysis of charred wheat grains could be a good tool for reconstructing past climate change and identifying ancient irrigation practices.

Prediction and validation of burnout curves for Goettelborn char using reaction kinetics determined in shock tube experiments

Energy Technology Data Exchange (ETDEWEB)

Moors, J.H.J.; Banin, V.E.; Haas, J.H.P.; Weber, R.; Veefkind, A. [Eindhoven University of Technology, Eindhoven (Netherlands). Dept. of Applied Physics

1999-01-01

Using a shock tube facility the combustion characteristics of pulverised char ({lt} 10 {mu}m) were measured. A prediction was made for the burnout behaviour of a commercial sized char particle (75-90 {mu}m) in different ambient conditions using a `pseudo kinetic` approach. In this approach the kinetic rate of a surface containing micro pores is determined and these `pseudo kinetics` are then applied to the larger particle not taking into account the micro pores. Comparison of the predictions with measurements done with an isothermal plug flow reactor showed this approach to be valid within experimental error for low burnout. A linear decrease of the kinetic reaction rate with burnout is shown to predict the burnout behaviour in the complete range of burnout. A possible explanation for this linear decrease could be a growing fraction of non-combustible material in the char particles during burnout. 11 refs., 6 figs., 2 tabs.

The potential of activated carbon derived from bio-char waste of bio-oil pyrolysis as adsorbent

Directory of Open Access Journals (Sweden)

Zulkania Ariany

2018-01-01

Full Text Available Activated carbon from bio-char waste of bio oil pyrolysis of mixed sugarcane bagasse and Rambutan twigs was investigated. Bio-char as by-product of bio-oil pyrolysis has potential to be good adsorbed by activating process. Bio-chars waste was activated in fixed bed reactor inside furnace without presenting oxygen. Gas N2 and CO2 were employed to drive out oxygen from the reactor and as activator, respectively. One of the best activation treatments is achieved by performing activation in different temperature and time to produce standard activated carbon. The experiment was performed at different temperatures and activation time, i.e. 800, 850, and 900° C and 80 and 120 minutes, respectively, to determine the optimal operating condition. Activated carbon was characterized by analysis of moisture content, ash content pH, and methylene blue test. The results showed that optimum activation was at 850°C and 80 minute, where activated carbon produced indicated the best adsorption capacity. The ash content and pH had significant role in resulting good activated carbon.

Slash-and-char: An ancient agricultural technique holds new promise for management of soils contaminated by Cd, Pb and Zn

International Nuclear Information System (INIS)

Niu, Li-qin; Jia, Pu; Li, Shao-peng; Kuang, Jia-liang; He, Xiao-xin; Zhou, Wen-hua; Liao, Bin; Shu, Wen-sheng; Li, Jin-tian

2015-01-01

Heavy metal contamination of agricultural soils is of worldwide concern. Unfortunately, there are currently no efficient and sustainable approaches for addressing this concern. In this study, we conducted a field experiment in which an agricultural soil highly contaminated by cadmium (Cd), lead (Pb) and zinc (Zn) was treated on-site by an ancient agricultural technique, ‘slash-and-char’, that was able to convert the biomass feedstock (rice straw) into biochar in only one day. We found evidence that in comparison to the untreated soil, the treated soil was associated with decreased bioavailability of the heavy metals and increased vegetable yields. Most importantly, the treatment was also coupled with dramatic reductions in concentrations of the heavy metals in vegetables, which made it possible to produce safe crops in this highly contaminated soil. Collectively, our results support the idea that slash-and-char offers new promise for management of soils contaminated by Cd, Pb and Zn. - Highlights: • We explored the potential of slash-and-char in dealing with soil metal pollution. • Metal bioavailability in the soil treated with slash-and-char was reduced by 24–65%. • Vegetable yield in the soil treated with slash-and-char was increased by 34–67%. • Slash-and-char could reduce the metal concentration in vegetables to a safe level. - An ancient agricultural technique called ‘slash-and-char’ offers new promise for management of soils contaminated multiply by Cd, Pb and Zn

Sugarcane vinasse CO2 gasification and release of ash-forming matters in CO2 and N2 atmospheres.

Science.gov (United States)

Dirbeba, Meheretu Jaleta; Brink, Anders; DeMartini, Nikolai; Lindberg, Daniel; Hupa, Mikko

2016-10-01

Gasification of sugarcane vinasse in CO2 and the release of ash-forming matters in CO2 and N2 atmospheres were investigated using a differential scanning calorimetry and thermogravimetric analyzer (DSC-TGA) at temperatures between 600 and 800°C. The results showed that pyrolysis is the main mechanism for the release of the organics from vinasse. Release of ash-forming matters in the vinasse is the main cause for vinasse char weight losses in the TGA above 700°C. The losses are higher in N2 than in CO2, and increase considerably with temperature. CO2 gasification also consumes the carbon in the vinasse chars while suppressing alkali release. Alkali release was also significant due to volatilization of KCl and reduction of alkali sulfate and carbonate by carbon. The DSC measured thermal events during heating up in N2 atmosphere that correspond to predicted melting temperatures of alkali salts in the char. Copyright © 2016 Elsevier Ltd. All rights reserved.

CharToon 2.1 extensions : expression repertoire and lip sync

OpenAIRE

Ruttkay, Z.M.; Lelièvre, Alban

2000-01-01

textabstractCharToon is a modular system to design and animate 21/2D faces and other graphic al objects. This report contains the extensions made for version 2.1, effecting only the Animation Editor module. The new features allow the re-usage of a reper toire of expression snapshots and animations and automatic generation of lip-syn c from phoneme and/or viseme sequences.

The influence of included minerals on the intrinsic reactivity of chars prepared under N{sub 2} and CO{sub 2} environment

Energy Technology Data Exchange (ETDEWEB)

Zhang, Hong; Li, Huan; Chen, Jiabao; Zhao, Bo; Hu, Guangzhou [China Univ. of Mining and Technology, Jiangsu (China). School of Chemical Engineering

2013-07-01

Oxy-fuel technology could be successfully used to retrofit existing coal-fired power plants or alternatively be used to design and build new coal-fired power plants with almost zero emissions. Char reactivity under oxy-fuel conditions will have a significant impact on the coal burnout. In this paper, two fractions, representing organic-rich particles and organic particles with included minerals, were separated from each of three Chinese coals of different rank. They were then devolatilized at 1,450 C in a drop tube furnace (DTF) under N{sub 2} and CO{sub 2} environment, respectively. The chars were subjected to nitrogen adsorption study, thermogravimetric analysis and XRD analysis. It was found that char reactivity of all three pairs of chars were increased under CO{sub 2} environment as compared with that under N{sub 2} environment, but with differing trend. For the organic-rich samples the reactivity difference is increased with decreasing rank. On the contrary, for the samples of organic particles with included minerals, the reactivity difference is decreased with decreasing rank. Mechanism analysis showed that they are resulted not from gasification, but from a combination of changes in surface area and in the orderness of carbon structure in the chars, both of which, in turn, are resulted from the higher heat capacity of CO{sub 2} and the interaction between metastable liquid phase and the included minerals.

Analysis of Porous Structure Parameters of Biomass Chars Versus Bituminous Coal and Lignite Carbonized at High Pressure and Temperature—A Chemometric Study

Directory of Open Access Journals (Sweden)

Adam Smoliński

2017-09-01

Full Text Available The characteristics of the porous structure of carbonized materials affect their physical properties, such as density or strength, their sorption capacity, and their reactivity in thermochemical processing, determining both their applicability as fuels or sorbents and their efficiency in various processes. The porous structure of chars is shaped by the combined effects of physical and chemical properties of a carbonaceous material and the operating parameters applied in the carbonization process. In the study presented, the experimental dataset covering parameters of various fuels, ranging from biomass through lignite to bituminous coal, and chars produced at 1273 K and under the pressure of 1, 2, 3, and 4 MPa was analyzed with the application of the advanced method of data exploration. The principal component analysis showed that the sample of the highest coal rank was characterized by lower values of parameters reflecting the development of the porous structure of chars. A negative correlation was also observed between the carbon content in a fuel and the evolution of the porous structure of chars at high pressure. The highest total pore volume of chars produced under 1 and 3 MPa and the highest micropore surface area under 3 MPa were reported for a carbonized fuel sample of the highest moisture content.

Development of polymer films by the coalescence of polymer particles in powdered and aqueous polymer-modified mortars

International Nuclear Information System (INIS)

Afridi, M.U.K.; Ohama, Y.; Demura, K.; Iqbal, M.Z.

2003-01-01

This paper evaluates and compares the coalescence of polymer particles (continuous polymer films formation) in powdered polymer-modified mortars (PPMMs) and aqueous polymer-modified mortars (APMMs). Polymer-modified mortars (PMMs) using various redispersible polymer powders (powdered cement modifiers) and polymer dispersions (aqueous cement modifiers) were prepared by varying the polymer-cement ratio (P/C) and were tested for the characterization of polymer films using a scanning electron microscope (SEM) after curing for 28 days. It is concluded from the test results that mortar constituents of unmodified mortar (UMM) are loosely joined with each other due to the absence of polymer films, thus having a structure with comparatively lower mechanical and durability characteristics. By contrast, mortar constituents in PPMMs and APMMs are compactly joined with each other due to the presence of interweaving polymer films, thereby forming a monolithic structure with improved mechanical and durability characteristics. However, the results make obvious the poor coalescence of polymer particles or development of inferior quality polymers films in PPMMs as compared to that observed in APMMs. Moreover, PPMMs show less uniform distribution of polymer films as compared to that in APMMs. Different powdered cement modifiers have different film-forming capabilities. However, such difference is hardly recognized in aqueous cement modifiers. The polymer films in PPMMs and APMMs may acquire different structures. They may appear as mesh-like, thread-like, rugged, dense or fibrous with fine or rough surfaces. Development of coherent polymer films is not well pronounced at a P/C of 5% in PPMMs, whereas sometimes coherent polymer films are observed at a P/C of 5% in APMMs. At a P/C of 10% or more, fully developed, coherent polymer films are observed in both PPMMs and APMMs

Reactive polymer fused deposition manufacturing

Science.gov (United States)

Kunc, Vlastimil; Rios, Orlando; Love, Lonnie J.; Duty, Chad E.; Johs, Alexander

2017-05-16

Methods and compositions for additive manufacturing that include reactive or thermosetting polymers, such as urethanes and epoxies. The polymers are melted, partially cross-linked prior to the depositing, deposited to form a component object, solidified, and fully cross-linked. These polymers form networks of chemical bonds that span the deposited layers. Application of a directional electromagnetic field can be applied to aromatic polymers after deposition to align the polymers for improved bonding between the deposited layers.

Phosphate-induced metal stabilization: Use of apatite and bone char for the removal of soluble radionuclides in authentic and simulated DOE groundwater

International Nuclear Information System (INIS)

Bostick, W.D.; Jarabek, R.J.; Conca, J.L.

1999-01-01

The apatite group of minerals is a family of calcium phosphate phases. Apatite is the principal component of bone tissue, and it also occurs naturally as mineral deposits in the geosphere. Bone char is calcined (coked) animal bone, containing activated carbon as well as calcium phosphate mineral phases. Apatite IItrademark is a more reactive form of apatite, supplied by UFA Ventures, Inc., at a cost of approximately 1/4 that of commercial bone char. Apatite is shown to be effective for the removal of select heavy metal impurities in groundwater. Previous investigations have demonstrated that apatite is an effective medium for the stabilization of soluble lead, cadmium, and zinc from mine waste leachate by the formation of highly insoluble precipitate phases. The performance of bone char and apatite II are compared with other candidate sorption media (including granular activated carbon and anion exchange resin) for the removal of soluble uranyl ion in synthetic DOE Site groundwater supplemented with varying levels of interfering nitrate ion. Apatite II has a greater affinity for U(VI), especially in the presence of nitrate ion, as evidenced by a larger value for the conditional distribution coefficient (Kd) in batch test experiments. Contact of uranyl nitrate solution with apatite II is shown to produce highly insoluble mineral phases of the autunite group (calcium uranyl phosphate hydrates). Apatite II is also demonstrated to be moderately effective for the removal of soluble radioactive isotopes of strontium, but not cesium, when these ions are supplemented into authentic DOE Site groundwater

Study on demetalization of sewage sludge by sequential extraction before liquefaction for the production of cleaner bio-oil and bio-char.

Science.gov (United States)

Leng, Lijian; Yuan, Xingzhong; Shao, Jianguang; Huang, Huajun; Wang, Hou; Li, Hui; Chen, Xiaohong; Zeng, Guangming

2016-01-01

Demetalization of sewage sludge (SS) by sequential extraction before liquefaction was implemented to produce cleaner bio-char and bio-oil. Demetalization steps 1 and 2 did not cause much organic matter loss on SS, and thus the bio-oil and bio-char yields and the compositions of bio-oils were also not affected significantly. However, the demetalization procedures resulted in the production of cleaner bio-chars and bio-oils. The total concentrations and the acid soluble/exchangeable fraction (F1 fraction, the most toxic heavy metal fraction) of heavy metals (Cu, Cr, Pb, Zn, and Cd) in these products were significantly reduced and the environmental risks of these products were also relived considerably compared with those produced from raw SS, respectively. Additionally, these bio-oils had less heavy fractions. Demetalization processes with removal of F1 and F2 fractions of heavy metals would benefit the production of cleaner bio-char and bio-oil by liquefaction of heavy metal abundant biomass like SS. Copyright © 2015 Elsevier Ltd. All rights reserved.

Morphological changes during oxidation of a single char particle. Quarterly progress report, April 30, 1992

Energy Technology Data Exchange (ETDEWEB)

d`Amore, M. [Salerno Univ. (Italy). Dept. of Chemical and Food Engineering; Tognotti, L. [Pisa Univ. (Italy). Dept. of Chemical Engineering; Sarofim, A.F. [Massachusetts Inst. of Tech., Cambridge, MA (United States). Dept. of Chemical Engineering

1992-12-31

In this study, the changes with conversion in morphology of a carbon char in the temperature range 500--1200 K are followed by using an electrodynamic balance (EDB) (Spjut et al., 1985; Dudek, 1988; Bar-ziv et al., 1989). This device allows one to measure in situ, over temperature range wider than in other apparatuses, mass, diameter, density, surface area, rate of reaction and temperature for a single, suspended submillimeter particle. By following with the EDB the changes in the char as it reacts, it is possible to study the influence of the porous texture on the reaction behavior and shed some light on the contribution by micropores to the reaction in the chemical kinetic controlled regime.

Infrared laser-induced chaos and conformational disorder in a model polymer crystal: Melting vs ablation

International Nuclear Information System (INIS)

Sumpter, B.G.; Noid, D.W.; Voth, G.A.; Wunderlich, B.

1990-01-01

Molecular dynamics-based computer simulations are presented for the interaction of one and two infrared (IR) laser beams with a model polymer surface. When a single laser beam system is studied over a wide range of intensities, only melting of the polymer, or melting followed by bond dissociation, is observed for up to 100 picoseconds. In contrast, the two-laser simulation results exhibit a marked difference in the energy absorption behavior of the irradiated polymer which, in turn, results in multiple bond dissociations. The results for the one- and two-laser cases studied can be divided into four different classes of physical behavior: (a) the polymer remains in the solid state; (b) the polymer crystal melts; (c) the polymer ablates, but with significant melting (charring); or (d) the polymer ablates with minimal melting. Damage to the model polymer crystal from absorption of energy from either one or two lasers occurs through a mechanism that involves the competition between the absorption of energy and internal energy redistribution. The rate of energy loss from the absorption site(s) relative to the rate of absorption of energy from the radiation field determines rather the polymer melts or ablates (low absorption rates lead to melting or no change and high rates lead to ablation). A sufficiently large rate of energy absorption is only obtainable through the use of two lasers. Two lasers also significantly decrease the total laser intensity required to cause polymer crystal melting. The differences between the one- and two-laser cases are studied by adapting novel signal/subspace techniques to analyze the dynamical changes in the mode spectrum of the polymer as it melts

Review of Synthetic Methods to Form Hollow Polymer Nanocapsules

Energy Technology Data Exchange (ETDEWEB)

Barker, Madeline T. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2014-03-13

Syntactic foams have grown in interest due to the widened range of applications because of their mechanical strength and high damage tolerance. In the past, hollow glass or ceramic particles were used to create the pores. This paper reviews literature focused on the controlled synthesis of hollow polymer spheres with diameters ranging from 100 –200 nm. By using hollow polymer spheres, syntactic foams could reach ultra-low densities.

Simultaneous determination of devolatilization and char burnout times during fluidized bed combustion of coal

International Nuclear Information System (INIS)

Christofiedes, N.; Brown, R.C.

1992-01-01

In this paper, the authors investigate a method for simultaneous determination of devolatilization and char burnout times based on the analysis of CO 2 emissions from a fluidized bed combustor. The technique is non-intrusive and can be performed under realistic combustion conditions. The authors' method involves batching single-size coal samples in a fluidized bed combustor that is heated with propane gas or other fuel. Carbon dioxide profiles versus time for the batch tests are analyzed with a linear model to obtain characteristic time constants for coal devolatilization and char combustion which can be related to total devolatilization time and burnout time for a coal sample. The authors' approach does not require special sample preparation, can be performed in actual combustion equipment and employs standard boiler instrumentation

Collective dynamics of glass-forming polymers at intermediate length scales

International Nuclear Information System (INIS)

Colmenero, J.; Alvarez, F.; Arbe, A.

2015-01-01

Deep understanding of the complex dynamics taking place in glass-forming systems could potentially be gained by exploiting the information provided by the collective response monitored by coherent neutron scattering. We have revisited the question of the characterization of the collective response of polyisobutylene at intermediate length scales observed by neutron spin echo (NSE) experiments. The model, generalized for sub-linear diffusion - as it is the case of glass-forming polymers - has been successfully applied by using the information on the total self-motions available from MD-simulations properly validated by direct comparison with experimental results. From the fits of the coherent NSE data, the collective time at Q → 0 has been extracted that agrees very well with compiled results from different experimental techniques directly accessing such relaxation time. We show that a unique temperature dependence governs both, the Q → 0 and Q → ∞ asymptotic characteristic times. The generalized model also gives account for the modulation of the apparent activation energy of the collective times with the static structure factor. It mainly results from changes of the short-range order at inter-molecular length scales

Thermal characteristics and surface morphology of char during co-pyrolysis of low-rank coal blended with microalgal biomass: Effects of Nannochloropsis and Chlorella.

Science.gov (United States)

Wu, Zhiqiang; Yang, Wangcai; Yang, Bolun

2018-02-01

In this work, the influence of Nannochloropsis and Chlorella on the thermal behavior and surface morphology of char during the co-pyrolysis process were explored. Thermogravimetric and iso-conversional methods were applied to analyzing the pyrolytic and kinetic characteristics for different mass ratios of microalgae and low-rank coal (0, 3:1, 1:1, 1:3 and 1). Fractal theory was used to quantitatively determine the effect of microalgae on the morphological texture of co-pyrolysis char. The result indicated that both the Nannochloropsis and Chlorella promoted the release of volatile from low-rank coal. Different synergistic effects on the thermal parameters and yield of volatile were observed, which could be attributed to the different compositions in the Nannochloropsis and Chlorella and operating condition. The distribution of activation energies shows nonadditive characteristics. Fractal dimensions of the co-pyrolysis char were higher than the individual char, indicating the promotion of disordered degree due to the addition of microalgae. Copyright © 2017 Elsevier Ltd. All rights reserved.

Micelles Formed by Polypeptide Containing Polymers Synthesized Via N-Carboxy Anhydrides and Their Application for Cancer Treatment

Directory of Open Access Journals (Sweden)

Dimitrios Skoulas

2017-06-01

Full Text Available The development of multifunctional polymeric materials for biological applications is mainly guided by the goal of achieving the encapsulation of pharmaceutical compounds through a self-assembly process to form nanoconstructs that control the biodistribution of the active compounds, and therefore minimize systemic side effects. Micelles are formed from amphiphilic polymers in a selective solvent. In biological applications, micelles are formed in water, and their cores are loaded with hydrophobic pharmaceutics, where they are solubilized and are usually delivered through the blood compartment. Even though a large number of polymeric materials that form nanocarrier delivery systems has been investigated, a surprisingly small subset of these technologies has demonstrated potentially curative preclinical results, and fewer have progressed towards commercialization. One of the most promising classes of polymeric materials for drug delivery applications is polypeptides, which combine the properties of the conventional polymers with the 3D structure of natural proteins, i.e., α-helices and β-sheets. In this article, the synthetic pathways followed to develop well-defined polymeric micelles based on polypeptides prepared through ring-opening polymerization (ROP of N-carboxy anhydrides are reviewed. Among these works, we focus on studies performed on micellar delivery systems to treat cancer. The review is limited to systems presented from 2000–2017.

A Sub-Microanalysis Approach in Chemical Characterisation of Gold Nanorods Formed by a Novel Polymer-Immobilised Gold Seeds Base

Directory of Open Access Journals (Sweden)

Majid Kazemian Abyaneh

2017-10-01

Full Text Available Gold nanorods (GNRs have been fabricated by a novel polymer-immobilised seed mediated method using ultraviolet (UV photoreduced gold-polymethylmethacrylate (Au–PMMA nanocomposites as a seed platform and characterised at sub-micron scale regime with synchrotron-based techniques; near-edge X-ray absorption fine structure (NEXAFS spectroscopy and X-ray fluorescence (XRF mapping. In this report, it is shown that investigating polymer nanocomposites using combination of XRF mapping and NEXAFS spectromicroscopy can help to see the growth phenomenon from different perspective than conventional characterisation techniques. XRF maps are used to explore distribution of the constituent elements and showing how polymer matrix making stripe patterns along with regions where GNRs are formed. NEXAFS carbon (C K-edge spectra have been taken at three different stages of synthesis: (1 on Au–PMMA nanocomposites before UV irradiation, (2 after gold nanoparticles formation, and (3 after GNRs formation. It reveals how polymer matrix has been degraded during GNRs formation and avoiding chemically or physically damage to polymer matrix is crucial to control the formation of GNRs.

Promotion of hydrogen-rich gas and phenolic-rich bio-oil production from green macroalgae Cladophora glomerata via pyrolysis over its bio-char.

Science.gov (United States)

Norouzi, Omid; Jafarian, Sajedeh; Safari, Farid; Tavasoli, Ahmad; Nejati, Behnam

2016-11-01

Conversion of Cladophora glomerata (C. glomerata) as a Caspian Sea's green macroalgae into gaseous, liquid and solid products was carried out via pyrolysis at different temperatures to determine its potential for bio-oil and hydrogen-rich gas production for further industrial utilization. Non-catalytic tests were performed to determine the optimum condition for bio-oil production. The highest portion of bio-oil was retrieved at 500°C. The catalytic test was performed using the bio-char derived at 500°C as a catalyst. Effect of the addition of the algal bio-char on the composition of the bio-oil and also gaseous products was investigated. Pyrolysis derived bio-char was characterized by BET, FESEM and ICP method to show its surface area, porosity, and presence of inorganic metals on its surface, respectively. Phenols were increased from 8.5 to 20.76area% by the addition of bio-char. Moreover, the hydrogen concentration and hydrogen selectivity were also enhanced by the factors of 1.37, 1.59 respectively. Copyright © 2016 Elsevier Ltd. All rights reserved.

Advanced char burnout models for the simulation of pulverized coal fired boilers

Energy Technology Data Exchange (ETDEWEB)

T. Severin; S. Wirtz; V. Scherer [Ruhr-University, Bochum (Germany). Institute of Energy Plant Technology (LEAT)

2005-07-01

The numerical simulation of coal combustion processes is widely used as an efficient means to predict burner or system behaviour. In this paper an approach to improve CFD simulations of pulverized coal fired boilers with advanced coal combustion models is presented. In simple coal combustion models, first order Arrhenius rate equations are used for devolatilization and char burnout. The accuracy of such simple models is sufficient for the basic aspects of heat release. The prediction of carbon-in-ash is one aspect of special interest in the simulation of pulverized coal fired boilers. To determine the carbon-in-ash levels in the fly ash of coal fired furnaces, the char burnout model has to be more detailed. It was tested, in how far changing operating conditions affect the carbon-in-ash prediction of the simulation. To run several test cases in a short time, a simplified cellnet model was applied. To use a cellnet model for simulations of pulverized coal fired boilers, it was coupled with a Lagrangian particle model, used in CFD simulations, too. 18 refs., 5 figs., 5 tabs.

Mineral-char interaction during gasification of high-ash coals in fluidized-bed gasification

CSIR Research Space (South Africa)

Oboirien, BO

2011-09-01

Full Text Available -enriched conditions, while X-ray spectroscopy [and energy-dispersive spectrometry (EDS)] mapping was used to determine the distribution of elements, such as Si, Al, Mg, Ca, and K, in the same chars. The higher ordered structure of the carbon around the melted minerals...

Syngas production by gasification of aquatic biomass with CO2/O2 and simultaneous removal of H2S and COS using char obtained in the gasification

International Nuclear Information System (INIS)

Hanaoka, Toshiaki; Hiasa, Shou; Edashige, Yusuke

2013-01-01

Applicability of gulfweed as feedstock for a biomass-to-liquid (BTL) process was studied for both production of gas with high syngas (CO + H 2 ) content via gasification of gulfweed and removal of gaseous impurities using char obtained in the gasification. Gulfweed as aqueous biomass was gasified with He/CO 2 /O 2 using a downdraft fixed-bed gasifier at ambient pressure and 900 °C at equivalence ratios (ER) of 0.1–0.3. The syngas content increased while the conversion to gas on a carbon basis decreased with decreasing ER. At an ER of 0.1 and He/CO 2 /O 2 = 0/85/15%, the syngas content was maximized at 67.6% and conversion to gas on a carbon basis was 94.2%. The behavior of the desulfurization using char obtained during the gasification process at ER = 0.1 and He/CO 2 /O 2 = 0/85/15% was investigated using a downdraft fixed-bed reactor at 250–550 °C under 3 atmospheres (H 2 S/N 2 , COS/N 2 , and a mixture of gases composed of CO, CO 2 , H 2 , N 2 , CH 4 , H 2 S, COS, and steam). The char had a higher COS removal capacity at 350 °C than commercial activated carbon because (Ca,Mg)S crystals were formed during desulfurization. The char simultaneously removed H 2 S and COS from the mixture of gases at 450 °C more efficiently than did activated carbon. These results support this novel BTL process consisting of gasification of gulfweed with CO 2 /O 2 and dry gas cleaning using self-supplied bed material. -- Highlights: • A product gas with high syngas content was produced from the gasification of gulfweed with CO 2 /O 2 . • The syngas content increased with decreasing the equivalence ratio. • The syngas content was maximized at 67.6% at an ER of 0.1 and He/CO 2 /O 2 = 0/85/15%. • The char simultaneously removed H 2 S and COS from a mixture of gases at 450 °C efficiently

Co-pyrolysis behaviour and kinetic of two typical solid wastes in China and characterisation of activated carbon prepared from pyrolytic char.

Science.gov (United States)

Ma, Yuhui; Niu, Ruxuan; Wang, Xiaona; Wang, Qunhui; Wang, Xiaoqiang; Sun, Xiaohong

2014-11-01

This is the first study on the co-pyrolysis of spent substrate of Pleurotus ostreatus and coal tar pitch, and the activated carbon prepared from the pyrolytic char. Thermogravimetry (TG) analysis was carried out taking spent substrate, coal tar pitch and spent substrate-coal tar pitch mixture. The activation energies of pyrolysis reactions were obtained via the Flynn-Wall-Ozawa and Kissinger-Akahira-Sunose methods. The kinetic models were determined by the master-plots method. The activated carbons were characterised by N2-adsorption, Fourier transform infrared spectroscopy and X-ray diffraction. Experimental results demonstrated a synergistic effect happened during co-pyrolysis, which was characterised by a decreased maximum decomposition rate and an enhanced char yield. The average activation energies of the pyrolysis reactions of spent substrate, coal tar pitch and the mixture were 115.94, 72.92 and 94.38 kJ mol(-1) for the Flynn-Wall-Ozawa method, and 112.17, 65.62 and 89.91 kJ mol(-1) for the Kissinger-Akahira-Sunose method. The reaction model functions were f(α) = (1-α)(3.42), (1-α)(1.72) and (1-α)(3.07) for spent substrate, coal tar pitch and the mixture, respectively. The mixture char-derived activated carbon had a Brunauer-Emmett-Teller surface area up to 1337 m(2) g(-1) and a total pore volume of 0.680 cm(3) g(-1). Mixing spent substrate with coal tar pitch led to the creation of more micropores and a higher surface area compared with the single spent substrate and coal tar pitch char. Also, the mixture char-derived activated carbon had a higher proportion of aromatic stacking. This study provides a reference for the utilisation of spent substrate and coal tar pitch via co-pyrolysis, and their pyrolytic char as a promising precursor of activated carbon. © The Author(s) 2014.

Characterisation of coal and chars in fluidised bed gasification

CSIR Research Space (South Africa)

Oboirien, BO

2009-03-01

Full Text Available impact on the physical structure of the residual char. 4 In summary, the distinct burnout characteristics of coals could be attributed to the differences in the macerals and microlithotypes compositions, and mineral matter distribution....0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 8.5 9.0 9.5 10.0 REFLECTANCE % RE LA TIV E FR EQ UE NC Y % Increasing reflectance, decreasing volatiles, expected Increase in ignition temperature and time for burn-out Figure...

Nanoporous polymer electrolyte

Science.gov (United States)

Elliott, Brian [Wheat Ridge, CO; Nguyen, Vinh [Wheat Ridge, CO

2012-04-24

A nanoporous polymer electrolyte and methods for making the polymer electrolyte are disclosed. The polymer electrolyte comprises a crosslinked self-assembly of a polymerizable salt surfactant, wherein the crosslinked self-assembly includes nanopores and wherein the crosslinked self-assembly has a conductivity of at least 1.0.times.10.sup.-6 S/cm at 25.degree. C. The method of making a polymer electrolyte comprises providing a polymerizable salt surfactant. The method further comprises crosslinking the polymerizable salt surfactant to form a nanoporous polymer electrolyte.

Characterization and Activation Study of Black Chars Derived from Cellulosic Biomass Pyrolyzed at Very High Temperature

Energy Technology Data Exchange (ETDEWEB)

Contescu, Cristian I. [Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States); Gallego, Nidia C. [Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States)

2017-03-01

The State of Tennessee, in partnership with the University of Tennessee (UT) and the Oak Ridge National Laboratory (ORNL), has created the RevV! Manufacturing voucher program to help Tennessee manufacturers gain access to the world-class resources at ORNL. As a part of this program, ORNL was working with Proton Power, Inc. (PPI), a rapidly growing company located in Lenoir City, Tennessee. PPI has developed a patented renewable energy system that uses biomass and waste sources to produce inexpensive hydrogen gas or synthetic fuels which are economically competitive with fossil fuels. The pyrolysis process used by PPI in their manufacturing chain generates significant amounts of black carbon char as by-product. The scope of ORNL collaboration with PPI was assessing the black carbon char as a potential feedstock for activated carbon production, as this could be a potentially new revenue stream. During 2015-2016 ORNL received eight char samples from PPI and characterized their initial properties, simulated their physical activation by carbon dioxide, prepared gram-size samples of physically activated carbons, and characterized their surface and porosity properties. This report presents a summary of the work methods employed and the results obtained in the collaborative project between ORNL and PPI.

Failure prediction for the optimization of stretch forming aluminium-polymer laminate foils used for pharmaceutical packaging

Science.gov (United States)

Müller, Simon; Weygand, Sabine M.

2018-05-01

Axisymmetric stretch forming processes of aluminium-polymer laminate foils (e.g. consisting of PA-Al-PVC layers) are analyzed numerically by finite element modeling of the multi-layer material as well as experimentally in order to identify a suitable damage initiation criterion. A simple ductile fracture criterion is proposed to predict the forming limits. The corresponding material constants are determined from tensile tests and then applied in forming simulations with different punch geometries. A comparison between the simulations and the experimental results shows that the determined failure constants are not applicable. Therefore, one forming experiment was selected and in the corresponding simulation the failure constant was fitted to its measured maximum stretch. With this approach it is possible to predict the forming limit of the laminate foil with satisfying accuracy for different punch geometries.

Combustion studies in a fluidised bed-The link between temperature, NO{sub x} and N{sub 2}O formation, char morphology and coal type

Energy Technology Data Exchange (ETDEWEB)

Valentim, B.; Lemos de Sousa, M.J. [Centro de Geologia da Universidade do Porto, Faculdade de Ciencias, Praca de Gomes Teixeira, 4099-002, Porto (Portugal); Abelha, P.; Boavida, D.; Gulyurtlu, I. [Departamento de Engenharia Energetica e Controlo Ambiental (DEECA), Instituto Nacional de Engenharia, Tecnologia e Inovacao (INETI), Estrada do Paco do Lumiar, 22, Edif. J, 1649-038, Lisboa (Portugal)

2006-06-06

Five commercially available high volatile bituminous coals from different origins were studied with the objective of characterizing their petrographic nature with respect to emissions of NO{sub x} and N{sub 2}O. The chars produced [at temperatures ranging from 700 to 1000 {sup o}C] from these coals were also petrographic ally analyzed to assess the contribution of char to NO{sub x} and N{sub 2}O formation during combustion. Vitrinite-rich coals produced higher porous chars (cenospheres and tenuinetworks) than those that are rich in inertinite. The former coals were, however, found to release lower concentrations of NO. Consistent with previous works, N{sub 2}O emissions were observed to decrease significantly with temperature, however, on the whole, the N{sub 2}O emissions from vitrinite-rich high volatile coals were less than those from inertinite-rich coals. Additionally, high porous chars were found to give rise to lower emissions of NO and N{sub 2}O. (author)

Efficient Air Desulfurization Catalysts Derived from Pig Manure Liquefaction Char

Directory of Open Access Journals (Sweden)

Rajiv Wallace

2017-11-01

Full Text Available Biochar from the liquefaction of pig manure was used as a precursor of H2S desulfurization adsorbents. In its inorganic matter, it contains marked quantities of calcium, magnesium and iron, which are known as hydrogen sulfide oxidation catalysts. The char was used either as-received or mixed with 10% nanographite. The latter was added to increase both the content of the carbon phase and conductivity. ZnCl2 in two different ratios of char to an activation agent (1:1 and 1:2 was used to create the porosity in the carbon phase. The content of the later was between 18–45%. The activated samples adsorbed 144 mg/g H2S. Sulfur was the predominant product of reactive adsorption. Its deposition in the pore system and blockage of the most active pores ceased the materials’ activity. The presence of the catalytic phase was necessary but not sufficient to guarantee good performance. The developed porosity, which can store oxidation products in the resulting composite, is essential for the good performance of the desulfurization process. The surface of the composite with nanographite showed the highest catalytic activity, similar to that of the commercial Midas® carbon catalyst. The results obtained indicate that a high quality reactive adsorbent/catalyst for H2S removal can be obtained from pig manure liquefaction wastes.

Usefulness of radiatively obtained acrylamide polymers for production of drug forms with controlled release of the therapeutic component

International Nuclear Information System (INIS)

Mosiniak, T.; Switek, W.

1988-01-01

Using 60 Co gamma radiation as a factor initiating polymerization and cross-linking of polymers, polyacrylamide matrices were formed with the following therapeutic agents: aspirin, amidopyrin, sodium salicylate. Gamma radiation doses ranged from 3.5 to 22.5 kGy, dose rate was 0.138 Gy x s -1 . Kinetics of the therapeutic agent release from the matrix polymers was determined by measurement of per cent of the drug release in the course of time and calculations of release rate constants. The preparations containing slowly released drugs were obtained. 12 figs., 2 tabs., 11 refs. (author)

Understanding how lake populations of arctic char are structured and function with special consideration of the potential effects of climate change: a multi-faceted approach.

Science.gov (United States)

Budy, Phaedra; Luecke, Chris

2014-09-01

Size dimorphism in fish populations, both its causes and consequences, has been an area of considerable focus; however, uncertainty remains whether size dimorphism is dynamic or stabilizing and about the role of exogenous factors. Here, we explored patterns among empirical vital rates, population structure, abundance and trend, and predicted the effects of climate change on populations of arctic char (Salvelinus alpinus) in two lakes. Both populations cycle dramatically between dominance by small (≤300 mm) and large (>300 mm) char. Apparent survival (Φ) and specific growth rates (SGR) were relatively high (40-96%; SGR range 0.03-1.5%) and comparable to those of conspecifics at lower latitudes. Climate change scenarios mimicked observed patterns of warming and resulted in temperatures closer to optimal for char growth (15.15 °C) and a longer growing season. An increase in consumption rates (28-34%) under climate change scenarios led to much greater growth rates (23-34%). Higher growth rates predicted under climate change resulted in an even greater predicted amplitude of cycles in population structure as well as an increase in reproductive output (Ro) and decrease in generation time (Go). Collectively, these results indicate arctic char populations (not just individuals) are extremely sensitive to small changes in the number of ice-free days. We hypothesize years with a longer growing season, predicted to occur more often under climate change, produce elevated growth rates of small char and act in a manner similar to a "resource pulse," allowing a sub-set of small char to "break through," thus setting the cycle in population structure.

Tritium containing polymers having a polymer backbone substantially void of tritium

Science.gov (United States)

Jensen, G.A.; Nelson, D.A.; Molton, P.M.

1992-03-31

A radioluminescent light source comprises a solid mixture of a phosphorescent substance and a tritiated polymer. The solid mixture forms a solid mass having length, width, and thickness dimensions, and is capable of self-support. In one aspect of the invention, the phosphorescent substance comprises solid phosphor particles supported or surrounded within a solid matrix by a tritium containing polymer. The tritium containing polymer comprises a polymer backbone which is essentially void of tritium. 2 figs.

Numerical studies of the polymer melt flow in the extruder screw channel and the forming tool

Science.gov (United States)

Ershov, S. V.; Trufanova, N. M.

2017-06-01

To date, polymer compositions based on polyethylene or PVC is widely used as insulating materials. These materials processing conjugate with a number of problems during selection of the rational extrusion regimes. To minimize the time and cost when determining the technological regime uses mathematical modeling techniques. The paper discusses heat and mass transfer processes in the extruder screw channel, output adapter and the cable head. During the study were determined coefficients for three rheological models based on obtained viscosity vs. shear rate experimental data. Also a comparative analysis of this viscosimetric laws application possibility for studying polymer melt flow during its processing on the extrusion equipment was held. As a result of numerical study the temperature, viscosity and shear rate fields in the extruder screw channel and forming tool were obtained.

Polymer reinforcement of cement systems

International Nuclear Information System (INIS)

Swamy, R.N.

1979-01-01

In the last couple of decades several cement- and concrete-based composites have come into prominence. Of these, cement-polymer composites, like cement-fibre composites, have been recognised as very promising, and considerable research and development on their properties, fabrication methods and application are in progress. Of the three types of concrete materials which incorporate polymers to form composites, polymer impregnated concrete forms a major development in which hardened concrete is impregnated with a liquid monomer which is subsequently polymerized to form a rigid polymer network in the pores of the parent material. In this first part of the extensive review of the polymer reinforcement of cement systems, the process technology of the various monomer impregnation techniques and the properties of the impregnated composite are assessed critically. It is shown that the high durability and superior performance of polymer impregnated concrete can provide an economic and competitive alternative in in situ strengthening, and in other areas where conventional concrete can only at best provide adequate performance. The review includes a section on radiation-induced polymerization. (author)

Flat-flame burner studies of pulverized-coal combustion. Experimental results on char reactivity

Energy Technology Data Exchange (ETDEWEB)

Peck, R.E.; Shi, L.

1996-12-01

Structure of laminar, premixed pulverized-coal flames in a 1-D reactor has been studied with emphasis on char reactivity. A 1.1-meter-long tube furnace accommodated high-temperature environments and long residence times for the laminar flames produced by a flat-flame, coal-dust burner. Experiments were conducted at different operating conditions (fuel type/size, fuel-air ratio). Measurements included solid sample composition, major gas species and hydrocarbon species concentrations, and gas- and particle-phase line-of-sight temperatures at different axial locations in flames. Degree of char burnout increased with coal volatiles content and decreased with coal particle size. Combustion in furnace was in oxidizer-deficient environment and higher burnout was achieved as the fuel-air ratio neared stoichiometric. For 0-45 {mu}m particles most of the fixed carbon mass loss occurred within 5 cm of the furnace inlet, and char reaction was slow downstream due to low oxidizer concentrations. Fixed carbon consumption of the 45-90 {mu}m particles generally was slower than for the small particles. About 40%-80% of the fixed carbon was oxidized in the furnace. Primary volatiles mass loss occurred within the first 4.5 cm, and more than 90% of the volatiles were consumed in the flames. The flames stabilized in the furnace produced less CH{sub 4} and H{sub 2} in the burnt gas than similar unconfined flames. NO concentrations were found to decrease along the furnace and to increase with decreasing fuel/air ratio. Temperature measurement results showed that gas-phase temperatures were higher than solid-phase temperatures. Temperatures generally decreased with decreasing volatiles content and increased as the equivalence ratio approached one. The results can be used to interpret thermochemical processes occurring in pulverized-coal combustion. (au) 15 refs.

Study on the effect of heat treatment and gasification on the carbon structure of coal chars and metallurgical cokes using fourier transform Raman spectroscopy

Energy Technology Data Exchange (ETDEWEB)

S. Dong; P. Alvarez; N. Paterson; D.R. Dugwell; R. Kandiyoti [Imperial College London, London (United Kingdom). Department of Chemical Engineering

2009-03-15

Differences in the development of carbon structures between coal chars and metallurgical cokes during high-temperature reactions have been investigated using Raman spectroscopy. These are important to differentiate between different types of carbons in dust recovered from the top gas of the blast furnace. Coal chars have been prepared from a typical injectant coal under different heat-treatment conditions. These chars reflected the effect of peak temperature, residence time at peak temperature, heating rate and pressure on the evolution of their carbon structures. The independent effect of gasification on the development of the carbon structure of a representative coal char has also been studied. A similar investigation has also been carried out to study the effect of heat-treatment temperature (from 1300 to 2000{sup o}C) and gasification on the carbon structure of a typical metallurgical coke. Two Raman spectral parameters, the intensity ratio of the D band to the G band (I{sub D}/I{sub G}) and the intensity ratio of the valley between D and G bands to the G band (I{sub V}/I{sub G}), have been found useful in assessing changes in carbon structure. An increase in I{sub D}/I{sub G} indicates the growth of basic graphene structural units across the temperature range studied. A decrease in I{sub V}/I{sub G} appears to suggest the elimination of amorphous carbonaceous materials and ordering of the overall carbon structure. The Raman spectral differences observed between coal chars and metallurgical cokes are considered to result from the difference in the time-temperature history between the raw injectant coal and the metallurgical coke and may lay the basis for differentiation between metallurgical coke fines and coal char residues present in the dust carried over the top of the blast furnace. 41 refs., 17 figs., 3 tabs.

Pyrolysis of Lantana camara and Mimosa pigra: Influences of temperature, other process parameters and incondensable gas evolution on char yield and higher heating value.

Science.gov (United States)

Mundike, Jhonnah; Collard, François-Xavier; Görgens, Johann F

2017-11-01

Pyrolysis of invasive non-indigenous plants, Lantana camara (LC) and Mimosa pigra (MP) was conducted at milligram-scale for optimisation of temperature, heating rate and hold time on char yield and higher heating value (HHV). The impact of scaling-up to gram-scale was also studied, with chromatography used to correlate gas composition with HHV evolution. Statistically significant effects of temperature on char yield and HHV were obtained, while heating rate and hold time effects were insignificant. Milligram-scale maximised HHVs were 30.03MJkg -1 (525°C) and 31.01MJkg -1 (580°C) for LC and MP, respectively. Higher char yields and HHVs for MP were attributed to increased lignin content. Scaling-up promoted secondary char formation thereby increasing HHVs, 30.82MJkg -1 for LC and 31.61MJkg -1 for MP. Incondensable gas analysis showed that temperature increase beyond preferred values caused dehydrogenation that decreased HHV. Similarly, CO evolution profile explained differences in optimal HHV temperatures. Copyright © 2017 Elsevier Ltd. All rights reserved.

Thin Films Formed from Conjugated Polymers with Ionic, Water-Soluble Backbones

NARCIS (Netherlands)

Voortman, Thomas P; Chiechi, Ryan C

2015-01-01

This paper compares the morphologies of films of conjugated polymers in which the backbone (main chain) and pendant groups are varied between ionic/hydrophilic and aliphatic/hydrophobic. We observe that conjugated polymers in which the pendant groups and backbone are matched, either ionic-ionic or

Understanding how lake populations of arctic char are structured and function with special consideration of the potential effects of climate change: A multi-faceted approach.

Science.gov (United States)

Budy, Phaedra; Luecke, Chris

2014-01-01

Size dimorphism in fish populations, both its causes and consequences, has been an area of considerable focus; however, uncertainty remains whether size dimorphism is dynamic or stabilizing and about the role of exogenous factors. Here, we explored patterns among empirical vital rates, population structure, abundance and trend, and predicted the effects of climate change on populations of arctic char (Salvelinus alpinus) in two lakes. Both populations cycle dramatically between dominance by small (≤300 mm) and large (>300 mm) char. Apparent survival (Φ) and specific growth rates (SGR) were relatively high (40–96 %; SGR range 0.03–1.5 %) and comparable to those of conspecifics at lower latitudes. Climate change scenarios mimicked observed patterns of warming and resulted in temperatures closer to optimal for char growth (15.15 °C) and a longer growing season. An increase in consumption rates (28–34 %) under climate change scenarios led to much greater growth rates (23–34 %). Higher growth rates predicted under climate change resulted in an even greater predicted amplitude of cycles in population structure as well as an increase in reproductive output (Ro) and decrease in generation time (Go). Collectively, these results indicate arctic char populations (not just individuals) are extremely sensitive to small changes in the number of ice-free days. We hypothesize years with a longer growing season, predicted to occur more often under climate change, produce elevated growth rates of small char and act in a manner similar to a “resource pulse,” allowing a sub-set of small char to “break through,” thus setting the cycle in population structure.

Effectiveness of different pre-treatments in recovering pre-burial isotopic ratios of charred plants.

Science.gov (United States)

Brinkkemper, O; Braadbaart, F; van Os, B; van Hoesel, A; van Brussel, A A N; Fernandes, R

2018-02-15

Isotopic analysis of archaeological charred plant remains offers useful archaeological information. However, adequate sample pre-treatment protocols may be necessary to provide a contamination-free isotopic signal while limiting sample loss and achieving a high throughput. Under these constraints, research was undertaken to compare the performance of different pre-treatment protocols. Charred archaeological plant material was selected for isotopic analysis (δ 13 C and δ 15 N values) by isotope ratio mass spectrometry from a variety of plant species, time periods and soil conditions. Preservation conditions and the effectiveness of cleaning protocols were assessed through Fourier transform infrared spectroscopy and X-ray fluorescence (XRF) spectrometry. An acid-base-acid protocol, successfully employed in radiocarbon dating, was used to define a contamination-free isotopic reference. Acid-base-acid isotopic measurements were compared with those obtained from untreated material and an acid-only protocol. The isotopic signals of untreated material and the acid-only protocol typically did not differ more than 1‰ from those of the acid-base-acid reference. There were no significant isotopic offsets between acid-base-acid and acid-only or untreated samples. Sample losses in the acid-base-acid protocol were on average 50 ± 17% (maximum = 98.4%). Elemental XRF measurements showed promising results in the detection of more contaminated samples albeit with a high rate of false positives. For the large range of preservation conditions described in the study, untreated charred plant samples, water cleaned of sediments, provide reliable stable isotope ratios of carbon and nitrogen. The use of pre-treatments may be necessary under different preservation conditions or more conservative measurement uncertainties should be reported. Copyright © 2017 John Wiley & Sons, Ltd.

Char-recirculation biomass gasification system--a site-specific feasibility study

International Nuclear Information System (INIS)

Purdy, K.R.; Kerr, C.P.; Hensley, B.D.

1991-01-01

A site-specific feasibility study was conducted for a char-recirculation biomass gasification plant which would dispose of the chippable solid residues of the area sawmills. The plant would receive green hardwood chips and convert them into active charcoal while producing process steam and electrical power. An economic analysis was performed on the basis of not-for-profit operation, marketing crushed active charcoal to a broker at a discounted price, and displacing purchased electric power. Given a market for the active charcoal, the plant was judged to be economically viable

Porous carbon from local coconut shell char by CO2 and H2O activation in the presence of K2CO3

Science.gov (United States)

Vi, Nguyen Ngoc Thuy; Truyen, Dang Hai; Trung, Bien Cong; An, Ngo Thanh; Van Dung, Nguyen; Long, Nguyen Quang

2017-09-01

Vietnamese coconut shell char was activated by steam and carbon dioxide at low temperatures with the presence of K2CO3 as a catalyst. The effects of process parameters on adsorption capability of the product including different ratio of impregnation of activation agents, activation temperature, activation time were investigated in this study. Iodine number, methylene blue adsorption capacity, specific surface area and pore size distribution were measured to assess the properties of the activated carbon. Accordingly, the porous carbon was applied for toluene removal by adsorption technology. Significant increases in specific surface area and the toluene adsorption capacity were observed when the coconut shell char was activated in CO2 flow at 720 °C for 150 minutes and the K2CO3/char weight ratio of 0.5.

Solubilization of Phenol Derivatives in Polymer Micelles Formed by Cationic Block Copolymer

Directory of Open Access Journals (Sweden)

Irma Fuentes

2017-01-01

Full Text Available The aggregation of cationic block copolymers formed by polystyrene (PS and poly(ethyl-4-vinylpyridine (PS-b-PE4VP was studied in aqueous solution. Diblock copolymers of PS and poly(4-vinylpyridine were synthesized by sequential anionic polymerization using BuLi as initiator. Subsequently, the 4-vinylpyridine units were quaternized with ethyl bromide to obtain cationic PS-b-PE4VP block copolymers with different quaternization degree. The self-aggregation of cationic block copolymers was studied by fluorescence probing, whereas the morphology and size of polymer micelles were determined by transmission electronic microscopy. Results indicate that spherical micelles with sizes lower than 100 nm were formed, whereas their micropolarity decreases with increasing quaternization degree. The partition of phenols between the micellar and aqueous phase was studied by using the pseudo-phase model, and the results show that the partition coefficients increase with increasing length of the side alkyl chain and are larger for star micelles. These results are discussed in terms of three-region model.

Reversible networks in supramolecular polymers

NARCIS (Netherlands)

Havermans - van Beek, D.J.M.

2007-01-01

Non–covalent interactions between low molecular weight polymers form the basis of supramolecular polymers. The material properties of such polymers are determined by the strength and lifetime of the non–covalent reversible interactions. Due to the reversibility of the interactions between the low

A novel and facile strategy for highly flame retardant polymer foam composite materials: Transforming silicone resin coating into silica self-extinguishing layer.

Science.gov (United States)

Wu, Qian; Zhang, Qian; Zhao, Li; Li, Shi-Neng; Wu, Lian-Bin; Jiang, Jian-Xiong; Tang, Long-Cheng

2017-08-15

In this study, a novel strategy was developed to fabricate highly flame retardant polymer foam composite materials coated by synthesized silicone resin (SiR) polymer via a facile dip-coating processing. Applying the SiR polymer coating, the mechanical property and thermal stability of SiR-coated polymer foam (PSiR) composites are greatly enhanced without significantly altering their structure and morphology. The minimum oxygen concentration to support the combustion of foam materials is greatly increased, i.e. from LOI 14.6% for pure foam to LOI 26-29% for the PSiR composites studied. Especially, adjusting pendant group to SiOSi group ratio (R/Si ratio) of SiRs produces highly flame retardant PSiR composites with low smoke toxicity. Cone calorimetry results demonstrate that 44-68% reduction in the peak heat release rate for the PSiR composites containing different R/Si ratios over pure foam is achieved by the presence of appropriate SiR coating. Digital and SEM images of post-burn chars indicate that the SiR polymer coating can be transformed into silica self-extinguishing porous layer as effective inorganic barrier effect, thus preserving the polymer foam structure from fire. Our results show that the SiR dip-coating technique is a promising strategy for producing flame retardant polymer foam composite materials with improved mechanical properties. Copyright © 2017 Elsevier B.V. All rights reserved.

Approaches for Making High Performance Polymer Materials from Commodity Polymers

Institute of Scientific and Technical Information of China (English)

Xu Xi

2004-01-01

A brief surrey of ongoing research work done for improving and enhancing the properties of commodity polymers by the author and author's colleagues is given in this paper. A series of high performance polymers and polymer nanomaterials were successfully prepared through irradiation and stress-induced reactions of polymers and hydrogen bonding. The methods proposed are viable, easy in operation, clean and efficient.1. The effect of irradiation source (UV light, electron beam, γ -ray and microwave), irradiation dose, irradiation time and atmosphere etc. on molecular structure of polyolefine during irradiation was studied. The basic rules of dominating oxidation, degradation and cross-linking reactions were mastered. Under the controlled conditions, cross-linking reactions are prevented, some oxygen containing groups are introduced on the molecular chain of polyolefine to facilitate the interface compatibility of their blends. A series of high performance polymer materials: u-HDPE/PA6,u-HDPE/CaCO3, u-iPP/STC, γ-HDPE/STC, γ-LLDPE/ATH, e-HDPE, e-LLDPE and m-HDPEfilled system were prepared (u- ultraviolet light irradiated, γ- γ-ray irradiated, e- electron beam irradiated, m- microwave irradiated)2. The effect of ultrasonic irradiation, jet and pan-milling on structure and changes in properties of polymers were studied. Imposition of critical stress on polymer chain can cause the scission of bonds to form macroradicals. The macroradicals formed in this way may recombine or react with monomer or other radicals to form linear, branched or cross-linked polymers or copolymers. About 20 kinds of block/graft copolymers have been synthesized from polymer-polymer or polymer-monomer through ultrasonic irradiation.Through jet-milling, the molecular weight of PVC is decreased somewhat, the intensity of its crystalline absorption bonds becomes indistinct. The processability, the yield strength, strength at break and elongation at break of PVC get increased quite a lot after

Mechanical reinforcement and segmental dynamics of polymer nanocomposites

Science.gov (United States)

Gong, Shushan

The addition of nanofiller into a polymer matrix will dramatically change the physical properties of polymer. The introduction of nanofiller makes the polymer more applicable in many industries, such as automobile tires, coatings, semiconductors, and packaging. The altered properties are not the simple combination of the characters from the two components. The interactions in polymer nanocomposites play an important role in determining the physical properties. This dissertation focuses on the mechanical properties of polymer nanocomposites (silica/poly-2-vinylpyridine) above their glass transition temperature Tg, as a model for automobile tires, which utilize small silica particles in crosslinked rubber far above Tg. We also investigate the impacts of the interaction between particle filler and polymer matrix on the altered mechanical properties. Dielectric relaxation spectroscopy (DRS) is used to study the glassy bound polymer layers formed around the particles. The results show evidence of the existence of immobilized polymer layers at the surface of each nanoparticle. At the same time, the thickness of the immobilized polymer layers is quantified and formed to be around 2 nm. Then we consider particles with glassy bound polymer layers are bridged together (either rubbery bridge or glassy bridge) by polymer chains and form small clusters. Clusters finally percolate to form a particle-polymer network as loading fraction increases. Rheology is used to study the network formation, and to predict the boundary of rubbery bridge and glassy bridge regimes. The distance between particles determines the type of polymer bridging. The particle spacing larger than Kuhn length makes flexible (rubbery) bridge with rheology described by a flexible Rouse model for percolation. When the spacing is shorter than the Kuhn length (~ 1nm), stiffer bridge forms instead, which is called glassy bridge. The mechanical differences between rubbery bridge and glassy bridge, and the effect of

Predictive Method for Correct Identification of Archaeological Charred Grape Seeds: Support for Advances in Knowledge of Grape Domestication Process

Science.gov (United States)

Ucchesu, Mariano; Orrù, Martino; Grillo, Oscar; Venora, Gianfranco; Paglietti, Giacomo; Ardu, Andrea; Bacchetta, Gianluigi

2016-01-01

The identification of archaeological charred grape seeds is a difficult task due to the alteration of the morphological seeds shape. In archaeobotanical studies, for the correct discrimination between Vitis vinifera subsp. sylvestris and Vitis vinifera subsp. vinifera grape seeds it is very important to understand the history and origin of the domesticated grapevine. In this work, different carbonisation experiments were carried out using a hearth to reproduce the same burning conditions that occurred in archaeological contexts. In addition, several carbonisation trials on modern wild and cultivated grape seeds were performed using a muffle furnace. For comparison with archaeological materials, modern grape seed samples were obtained using seven different temperatures of carbonisation ranging between 180 and 340ºC for 120 min. Analysing the grape seed size and shape by computer vision techniques, and applying the stepwise linear discriminant analysis (LDA) method, discrimination of the wild from the cultivated charred grape seeds was possible. An overall correct classification of 93.3% was achieved. Applying the same statistical procedure to compare modern charred with archaeological grape seeds, found in Sardinia and dating back to the Early Bronze Age (2017–1751 2σ cal. BC), allowed 75.0% of the cases to be identified as wild grape. The proposed method proved to be a useful and effective procedure in identifying, with high accuracy, the charred grape seeds found in archaeological sites. Moreover, it may be considered valid support for advances in the knowledge and comprehension of viticulture adoption and the grape domestication process. The same methodology may also be successful when applied to other plant remains, and provide important information about the history of domesticated plants. PMID:26901361

Coal char combustion under a CO{sub 2}-rich atmosphere: Implications for pulverized coal injection in a blast furnace

Energy Technology Data Exchange (ETDEWEB)

Borrego, A.G.; Casal, M.D. [Instituto Nacional del Carbon, CSIC. P.O. Box 73, 33080 Oviedo (Spain); Osorio, E.; Vilela, A.C.F. [Laboratorio de Siderurgia, DEMET/PPGEM - Universidade Federal do Rio Grande do Sul. P.O. Box 15021, 91501-970 Porto Alegre (Brazil)

2008-11-15

Pulverized coal injection (PCI) is employed in blast furnace tuyeres attempting to maximize the injection rate without increasing the amount of unburned char inside the stack of the blast furnace. When coal is injected with air through the injection lance, the resolidified char will burn in an atmosphere with a progressively lower oxygen content and higher CO{sub 2} concentration. In this study an experimental approach was followed to separate the combustion process into two distinct devolatilization and combustion steps. Initially coal was injected into a drop tube furnace (DTF) operating at 1300 C in an atmosphere with a low oxygen concentration to ensure the combustion of volatiles and prevent the formation of soot. Then the char was refired into the DTF at the same temperature under two different atmospheres O{sub 2}/N{sub 2} (typical combustion) and O{sub 2}/CO{sub 2} (oxy-combustion) with the same oxygen concentration. Coal injection was also performed under a higher oxygen concentration in atmospheres typical for both combustion and oxy-combustion. The fuels tested comprised a petroleum coke and coals currently used for PCI injection ranging from high volatile to low volatile bituminous rank. Thermogravimetric analyses and microscopy techniques were used to establish the reactivity and appearance of the chars. Overall similar burnouts were achieved with N{sub 2} and CO{sub 2} for similar oxygen concentrations and therefore no loss in burnout should be expected as a result of enrichment in CO{sub 2} in the blast furnace gas. The advantage of increasing the amount of oxygen in a reacting atmosphere during burnout was found to be greater, the higher the rank of the coal. (author)

Evidence for a pore-filling mechanism in the adsorption of aromatic hydrocarbons to a natural wood char.

Science.gov (United States)

Nguyen, Thanh H; Cho, Hyun-Hee; Poster, Dianne L; Ball, William P

2007-02-15

Sorption isotherms for five aromatic hydrocarbons were obtained with a natural wood char (NC1) and its residue after solvent extraction (ENC1). Substantial isotherm nonlinearity was observed in all cases. ENC1 showed higher BET surface area, higher nitrogen-accessible micropore volume, and lower mass of extractable organic chemicals, including quantifiable polycyclic aromatic hydrocarbons (PAHs),while the two chars showed identical surface oxygen/ carbon (O/C) ratio. For two chlorinated benzenes that normally condense as liquids at the temperatures used, sorption isotherms with NC1 and ENC1 were found to be statistically identical. For the solid-phase compounds (1,4-dichlorobenzene (1,4-DCB) and two PAHs), sorption was statistically higher with ENC1, thus demonstrating sorption effects due to both (1) authigenic organic content in the sorbentand (2)the sorbate's condensed state. Polanyi-based isotherm modeling, pore size measurements, and comparisons with activated carbon showthe relative importance of adsorptive pore filling and help explain results. With both chars, maximum sorption increased in the order of decreasing molecular diameter: phenanthrene < naphthalene < 1,2-dichlorobenzene/1,2,4-trichlorobenzene < 1,4-DCB. Comparison of 1,4- and 1,2-DCB shows that the critical molecular diameter was apparently more important than the condensed state, suggesting that 1,4-DCB sorbed in the liquid state for ENC1.

Bioactivity of freeze-dried platelet-rich plasma in an adsorbed form on a biodegradable polymer material.

Science.gov (United States)

Nakajima, Yu; Kawase, Tomoyuki; Kobayashi, Mito; Okuda, Kazuhiro; Wolff, Larry F; Yoshie, Hiromasa

2012-01-01

Owing to the necessity for the immediate preparation from patients' blood, autologous platelet-rich plasma (PRP) limits its clinical applicability. To address this concern and respond to emergency care and other unpredictable uses, we have developed a freeze-dried PRP in an adsorbed form on a biodegradable polymer material (Polyglactin 910). On the polymer filaments of PRP mesh, which was prepared by coating the polymer mesh with human fresh PRP and subsequent freeze-drying, platelets were incorporated, and related growth factors were preserved at high levels. This new PRP mesh preparation significantly and reproducibly stimulated the proliferation of human periodontal ligament cells in vitro and neovascularization in a chorioallantoic membrane assay. A full-thickness skin defect model in a diabetic mouse demonstrated the PRP mesh, although prepared from human blood, substantially facilitated angiogenesis, granulation tissue formation, and re-epithelialization without inducing severe inflammation in vivo. These data demonstrate that our new PRP mesh preparation functions as a bioactive material to facilitate tissue repair/regeneration. Therefore, we suggest that this bioactive material, composed of allogeneic PRP, could be clinically used as a promising alternative in emergency care or at times when autologous PRP is not prepared immediately before application.

Effects of rice husks and their chars from hydrothermal carbonization on the germination rate and root length of Lepidium sativum

Science.gov (United States)

Kern, Jürgen; Mukhina, Irina; Dicke, Christiane; Lanza, Giacomo; Kalderis, Dimitrios

2015-04-01

Currently, char substrates gain a lot of interest, since they are being discussed as a component in growing media, which may become one option for the replacement of peat. Among different thermal conversion processes of biomass hydrothermal carbonization (HTC) has been found to produce chars with similar acidic pH values like peat. The question however is, if these hydrochars, which may contain toxic phenolic compounds are suitable to be introduced as a new substitute for peat in horticulture. In this study rice husk were hydrothermally carbonized at 200° C for 6 hours, yielding in hydrochars containing organic contaminants such as phenols and furfurals, which may affect plants and soil organisms. We investigated potential toxic effects on the germination rate and the root length of cress salad (Lepidium sativum) in four fractions: i) soil control, ii) raw rice husk + soil, iii) unwashed rice char + soil and iv) acetone/water washed rice char + soil. It could be shown that phenols and furfurals, which were removed from the hydrochar after washing by 80 to 96% did not affect the germination rate and the root length of the cress plants. The lowest germination rate and root length were found in the soil control, the highest in the non-washed hydrochar treatment, indicating a fertilization effect and growth stimulation of cress salad by hydrochar. If this result can be confirmed for other target and non-target organisms in future studies, a new strategy for the production of growing media may be developed.

Potential of aeration flow rate and bio-char addition to reduce greenhouse gas and ammonia emissions during manure composting

DEFF Research Database (Denmark)

Chowdhury, Md Albarune; de Neergaard, Andreas; Jensen, Lars Stoumann

2014-01-01

-char on GHG and NH3 emissions from composting cattle slurry and hen manure in small-scale laboratory composters. Depending on treatment, cumulative C losses via CO2 and CH4 emissions accounted for 11.4-22.5% and 0.004-0.2% of initial total carbon, while N losses as N2O and NH3 emissions comprised 0.......05-0.1% and 0.8-26.5% of initial total nitrogen, respectively. Decreasing the flow rate reduced cumulative NH3 losses non-significantly (by 88%) but significantly increased CH4 losses (by 51%) from composting of cattle slurry with barley straw. Among the hen manure treatments evaluated, bio-char addition...

Measurement and modeling the coefficient of restitution of char particles under simulated entrained flow gasifier conditions

Science.gov (United States)

Gibson, LaTosha M.

Inefficiencies in plant operations due to carbon loss in flyash, necessitate control of ash deposition and the handling of the slag disposal. Excessive char/ash deposition in convective coolers causes reduction in the heat transfer, both in the radiative (slagging) section and in the low-temperature convective (fouling) heating section. This can lead to unplanned shutdowns and result in an increased cost of electricity generation. CFD models for entrained flow gasification have used the average bulk coal composition to simulate slagging and ash deposition with a narrow particle size distribution (PSD). However, the variations in mineral (inorganic) and macerals (organic) components in coal have led to particles with a variation in their inorganic and organic composition after grinding as governed by their Particle Size Distribution (PSD) and mineral liberation kinetics. As a result, each particle in a PSD of coal exhibits differences in its conversion, particle trajectory within the gasifier, fragmentation, swelling, and slagging probability depending on the gasifier conditions (such as the temperature, coal to oxygen ratio, and swirling capacity of the coal injector). Given the heterogeneous behavior of char particles within a gasifier, the main objective of this work was to determine boundary conditions of char particle adhering and/or rebounding from the refractory wall or a layer of previously adhered particles. In the past, viscosity models based on the influence of ash composition have been used as the method to characterize sticking. It is well documented that carbon contributes to the non-wettability of particles. Therefore, it has been hypothesized that viscosity models would not be adequate to accurately predict the adhesion behavior of char. Certain particle wall impact models have incorporated surface tension which can account the contributions of the carbon content to the adhesive properties of a char particle. These particle wall impact models also

Antimocrobial Polymer

Science.gov (United States)

McDonald, William F.; Huang, Zhi-Heng; Wright, Stacy C.

2005-09-06

A polymeric composition having antimicrobial properties and a process for rendering the surface of a substrate antimicrobial are disclosed. The composition comprises a crosslinked chemical combination of (i) a polymer having amino group-containing side chains along a backbone forming the polymer, (ii) an antimicrobial agent selected from quaternary ammonium compounds, gentian violet compounds, substituted or unsubstituted phenols, biguanide compounds, iodine compounds, and mixtures thereof, and (iii) a crosslinking agent containing functional groups capable of reacting with the amino groups. In one embodiment, the polymer is a polyamide formed from a maleic anhydride or maleic acid ester monomer and alkylamines thereby producing a polyamide having amino substituted alkyl chains on one side of the polyamide backbone; the crosslinking agent is a phosphine having the general formula (A)3P wherein A is hydroxyalkyl; and the antimicrobial agent is chlorhexidine, dimethylchlorophenol, cetyl pyridinium chloride, gentian violet, triclosan, thymol, iodine, and mixtures thereof.

Polymer-induced liquid precursor (PILP) phases of calcium carbonate formed in the presence of synthetic acidic polypeptides - relevance to biomineralization

NARCIS (Netherlands)

Schenk, A.S.; Zope, H.; Kim, Y.; Kros, A.; Sommerdijk, N.A.J.M.; Meldrum, F.C.

2012-01-01

Polymer-induced liquid precursor (PILP) phases of calcium carbonate have attracted significant interest due to possible applications in materials synthesis, and their resemblance to intermediates seen in biogenic mineralisation processes. Further, these PILP phases have been formed in vitro using

Which kind of aromatic structures are produced during biomass charring? New insights provided by modern solid-state NMR spectroscopy

Science.gov (United States)

Knicker, Heike; Paneque-Carmona, Marina; Velasco-Molina, Marta; de la Rosa, José Maria; León-Ovelar, Laura Regina; Fernandez-Boy, Elena

2017-04-01

Intense research on biochar and charcoal of the last years has revealed that depending on the production conditions, the chemical and physical characteristics of their aromatic network can greatly vary. Since such variations are determining the behavior and stability of charred material in soils, a better understanding of the structural changes occurring during their heating and the impact of those changes on their function is needed. One method to characterize pyrogenic organic matter (PyOM) represents solid-state 13C NMR spectroscopy applying the cross polarization (CP) magic angle spinning technique (MAS). A drawback of this technique is that the quantification of NMR spectra of samples with highly condensed and proton-depleted structures is assumed to be bias. Typical samples with such attributes are charcoals produced at temperatures above 700°C under pyrolytic conditions. Commonly their high condensation degree leads to graphenic structures that are not only reducing the CP efficiency but create also a conductive lattice which acts as a shield and prevents the entering of the excitation pulse into the sample during the NMR experiments. Since the latter can damage the NMR probe and in the most cases the obtained NMR spectra show only one broad signal assignable to aromatic C, this technique is rarely applied for characterizing high temperature chars or soot. As a consequence, a more detailed knowledge of the nature of the aromatic ring systems is still missing. The latter is also true for the aromatic domains of PyOM produced at lower temperatures, since older NMR instruments operating at low magnetic fields deliver solid-state 13C NMR spectra with low resolution which turns a more detailed analysis of the aromatic chemical shift region into a challenging task. In order to overcome this disadvantages, modern NMR spectroscopy offers not only instruments with greatly improved resolution but also special pulse sequences for NMR experiments which allow a more

Sorption performance and mechanism of a sludge-derived char as porous carbon-based hybrid adsorbent for benzene derivatives in aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Kong, Lingjun [School of Environmental Science and Engineering, Sun Yat-Sen (Zhongshan) University, Guangzhou, 510275 (China); Xiong, Ya, E-mail: cesxya@mail.sysu.edu.cn [School of Environmental Science and Engineering, Sun Yat-Sen (Zhongshan) University, Guangzhou, 510275 (China); Guangdong Provincial Key Laboratory of Environmental Pollution Control and Remediation Technology, Guangzhou, 510275 (China); Sun, Lianpeng; Tian, Shuanghong [School of Environmental Science and Engineering, Sun Yat-Sen (Zhongshan) University, Guangzhou, 510275 (China); Guangdong Provincial Key Laboratory of Environmental Pollution Control and Remediation Technology, Guangzhou, 510275 (China); Xu, Xianyan; Zhao, Cunyuan [School of Chemistry and Chemical Engineering, Sun Yat-Sen (Zhongshan) University, Guangzhou, 510275 (China); Luo, Rongshu [School of Environmental Science and Engineering, Sun Yat-Sen (Zhongshan) University, Guangzhou, 510275 (China); Yang, Xin [School of Environmental Science and Engineering, Sun Yat-Sen (Zhongshan) University, Guangzhou, 510275 (China); Guangdong Provincial Key Laboratory of Environmental Pollution Control and Remediation Technology, Guangzhou, 510275 (China); Shih, Kaimin [Department of Civil Engineering, The University of Hong Kong, Pokfulam Road, Hong Kong SAR (China); Liu, Haiyang [Department of Chemistry, South China University of Technology, Guangzhou, 510641 (China)

2014-06-01

Highlights: • Hierarchical porous sludge char were fabricated by pyrolysis at 500 °C. • A stronger Si–O bond (1.83 Å and 1.87 Å) between the carboxyl and SiO{sub 2} was found. • Quantum chemistry calculation confirmed the interaction of Si–O and H–O bonds. • Multiple model (Q{sub T} = Q{sub A} + K{sub P}Ce) was presented in the sludge char sorption process. - Abstract: A porous sludge-derived char was prepared by a new one-step pyrolytic process with citric acid–ZnCl{sub 2} mixed fabricating-pore agents. The sludge-derived char was confirmed to be a hierarchically porous hybrid adsorbent containing-elemental carbon, -highly carbonized organic species and -inorganic ash with a great surface area of 792.4 m{sup 2} g{sup −1}. It was used as a carbon-based hybrid adsorbent for four benzene derivatives including 4-chlorophenol, phenol, benzoic acid and 4-hydroxylbenzoic acid in aqueous solution. Results showed that their sorption isotherms were nonlinear at low concentrations and linear at high concentrations. The sorption performance could be described by a multiple sorption model (Q{sub T} = Q{sub A} + K{sub P}C{sub e}). The order of these partition sorption coefficients (K{sub P}) of these benzene derivatives was consistent with their octanol–water partition coefficients (log K{sub ow}), but those saturated amounts (Q{sub A}) were inconsistent with their log K{sub ow}. The inconstancy was found to be considerably dependent on the preferential interaction of benzoic acid with SiO{sub 2} in the sludge-derived char. Quantum theoretical calculation confirmed that the preferential interaction was attributed to the formation of hydrogen bonds (1.61 and 1.69 Å) and new Si–O bonds (1.83 and 1.87 Å) between the carboxyl of benzoic acid and the SiO{sub 2} surface in the sorption process.

Fixation of tritium in a highly stable polymer form

International Nuclear Information System (INIS)

Steinberg, M.; Colombo, P.; Pruzansky, J.

1977-01-01

A method for the fixation of tritium comprises reacting tritiated water with calcium carbide to produce calcium hydroxide and tritiated acetylene, polymerizing the acetylene, and then incorporating the polymer in a solidifying matrix. 2 claims

Monomers capable of forming four hydrogen bridges and supramolecular polymers formed by copolymerization of these monomers with regular monomers

NARCIS (Netherlands)

2004-01-01

The invention relates to the synthesis of polymers containing self-complementary quadruple hydrogen groups by copolymerizing monomers containing a quadruple hydrogen bonding group with one or more monomers of choice. The resulting polymers show unique new characteristics due to the presence of

Thermal Conversion of Pine Wood Char to Carbon Nanomaterials in the Presence of Iron Nanoparticles

Science.gov (United States)

Sung Phil Mun; Zhiyong Cai; Fumiya Watanabe; Umesh P. Agarwal; Jilei. Zhang

2012-01-01

Southern yellow pine (Pinus taeda) wood char powder was thermally treated at 1,000:C in the presence of a 25-nm-size Fe nanoparticle catalyst. The thermally treated carbon materials were analyzed by Raman spectroscopy and high-resolution transmission electron microscopy. Well-aligned graphitic carbon structures with 15 to 17 layers on...

Deformation limits of polymer coated metal sheets

NARCIS (Netherlands)

Van Den Bosch, M.J.W.J.P.; Schreurs, P.J.G; Geers, M.G.D.

2005-01-01

Polymer coated metals are increasingly used by the packaging and automotive industry. During industrial deformation processes (drawing, roll-forming, bending etc.) the polymer-metal laminate is highly deformed at high deformation rates. These forming conditions can affect the mechanical integrity

Porphyrin coordination polymer nanospheres and nanorods

Science.gov (United States)

Wang, Zhongchun; Shelnutt, John A.; Medforth, Craig J.

2012-12-04

A porphyrin coordination polymer nanostructure comprising a network of pyridyl porphyrin molecules and coordinating metal ions coordinatively bound through the pyridyl groups. In some embodiments, the porphyrins are metalloporphyrins. A variety of nanostructures are formed by the network polymer, including nanospheres, polygonal nanostructures, nanorods, and nanofibers, depending on a variety of factors including coordination metal ion, porphyrin type, metal of the metalloporphyrin, and degree of agitation during nanostructure formation. Reduction of coordinating metal ions may be used to form metal nanoparticles on the coordination polymer nanostructure.

Fluid Structure Interaction Analysis in Manufacturing Metal/Polymer Macro-Composites

International Nuclear Information System (INIS)

Baesso, R.; Lucchetta, G.

2007-01-01

Polymer Injection Forming (PIF) is a new manufacturing technology for sheet metal-polymer macro-composites, which results from the combination of injection moulding and sheet metal forming. This process consists on forming the sheet metal according to the boundary of the mould cavity by means of the injected polymer. After cooling, the polymer bonds permanently to the metal resulting in a sheet metal-polymer macro-composite product. Comparing this process to traditional ones (where the polymeric and metal parts are joined together after separate forming) the main advantages are both reduction of production costs and increase of part quality. This paper presents a multi-physics numerical simulation of the process performed in the Ansys/CFX environment

Development of a wood-polymer composite by electron beam hardening

International Nuclear Information System (INIS)

Gotoda, Masao

1974-01-01

An incombustible wood-polymer composite (WPC) was studied. The dimensional stability was also tested. The comparison of conversion ratio was made between gamma-ray and electron beam and between a vinylidene chloride 100% impregnated beech composite and bulk. In the case of gamma-ray of low dose rate, the conversion ratio in the vinylidene chloride beech composite was lower than the bulk. In the case of electron beam, though dose rate was higher than that of gamma-ray, the conversion ratio was low, and was influenced by the moisture content of wood. The conversion ratio markedly decreased with the increase of the dose rate of electron beam. Roughly 50% polymer loading can be obtained when the dose rate of electron beam is low. In the case of gamma-ray, the effect of dimensional stability was approximately none with small polymer loading, whereas in the case of electron beam irradiation of moist wood, marked effect of dimensional stability was shown. Incombustibility effect was tested by burning a 150 mm long piece, in which three small pieces of 5 x 10 x 50 mm were connected with epoxy resin adhesive, with a Bunsen burner for 30 seconds. After the completion of burning, the long piece was separated back into three small pieces, and the char length, weight loss and after glow time were tested. The beech composite was expected to become incombustible at 40% polymer loading. The vinyl monomer solution of chlorinated aryl chloride oligomer can be easily hardened by electron beam irradiation. Addition of crosslinking agent such as trimethylol propane trimethracrylate prevents the dissolution of hardened methyl acrylate and methyl methacrylate by acetone. The electron beam hardening of aryl resin compound is possible, using benzen peroxide as a catalyst. Floor material can be produced by this process from low density, low price wood. (Iwakiri, K.)

Effect of coal rank and mineral matter on gasification reactivity of coal char treated at high temperature; Netsushorishita sekitan char no gas ka tokusei ni taisuru tanshu oyobi kobutsushitsu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Morishita, K.; Takei, H.; Harano, A.; Takarada, T. [Gunma University, Gunma (Japan). Faculty of Engineering

1996-10-28

In the wide range from brown coal to anthracite, an investigation was made of effects of heat treatment on physical/chemical properties and of coal rank dependence. For the experiment, 12 kinds of coal samples were used, and for heat treatment, the fluidized bed heated by the electric furnace and the infrared-ray gold image furnace were used. To examine characteristics of the heat-treated coal char, conducted were oxygen gasification, TPD measurement, XRD measurement, alkali metal measurement, and pore distribution measurement. The following were obtained from the experiment. The gasification reaction rate of the char heat-treated in the temperature range between 900{degree}C to 1700{degree}C decreases with a rise of the temperature of heat treatment, and the degree of decrease in the rate depends on coal rank. The order of gasification rate between coal ranks depends on the temperature of heat treatment, and the lower the heat treatment temperature is, the more largely the gasification rate is influenced by catalysis of mineral matters included in the coal. As causes of the decrease in gasification rate associated with the rise in temperature of heat treatment, indicated were release of alkali metal having catalysis and decrease of active sites by carbonaceous crystallinity. 6 figs.

a novel interconnected fluidised bed for the combined flash pyrolysis of biomass and combustion of char

NARCIS (Netherlands)

Janse, A.M.C.; Janse, Arthur M.C.; Biesheuvel, P.M.; Biesheuvel, Pieter Maarten; Prins, W.; van Swaaij, Willibrordus Petrus Maria

1999-01-01

A novel system of two adjacent fluidised beds operating in different gas atmospheres and exchanging solids was developed for the combined flash pyrolysis of biomass and combustion of the produced char. Fluidised sand particles (200 μm < dp < 400 μm) are transported from the pyrolysis reactor to the

A novel interconnected fluidised bed for the combined flash pyrolysis of biomass and combustion of char.

NARCIS (Netherlands)

Janse, Arthur M.C.; Janse, A.M.C.; Biesheuvel, P.M.; Biesheuvel, Pieter Maarten; Prins, W.; van Swaaij, Willibrordus Petrus Maria

2000-01-01

A novel system of two adjacent fluidised beds operating in different gas atmospheres and exchanging solids was developed for the combined flash pyrolysis of biomass and combustion of the produced char. Fluidised sand particles (200 μm < dp < 400 μm) are transported from the pyrolysis reactor to the

How do the poor handle money? What do the financial diaries of char dwellers tell us about financial inclusion?

Directory of Open Access Journals (Sweden)

Kuntala Lahiri-Dutt

2013-05-01

Full Text Available Derived from livelihoods surveys and ethnographic material about people living on the chars, or river islands, in deltaic lower Bengal, this paper illustrates the complex, diverse and ingenious ways that the poor manage money. These islands constitute some of the most vulnerable housing locations of some of the poorest communities; state services and facilities do not reach the chars because they are not listed as land in revenue records. It demonstrates that the poor live in a diverse economy where community spirit, family assistance and trust play roles equally important to markets. In doing so, it puts forth a grounded-in-the-field, evidence-based, critique of the slogan ‘financial inclusion’ that has gained prominence in recent years.

Polymers for energy storage and conversion

CERN Document Server

Mittal, Vikas

2013-01-01

One of the first comprehensive books to focus on the role of polymers in the burgeoning energy materials market Polymers are increasingly finding applications in the areas of energy storage and conversion. A number of recent advances in the control of the polymer molecular structure which allows the polymer properties to be more finely tuned have led to these advances and new applications. Polymers for Energy Storage and Conversion assimilates these advances in the form of a comprehensive text that includes the synthesis and properties of a large number of polymer systems for

Solid polymer electrolyte lithium batteries

Science.gov (United States)

Alamgir, Mohamed; Abraham, Kuzhikalail M.

1993-01-01

This invention pertains to Lithium batteries using Li ion (Li.sup.+) conductive solid polymer electrolytes composed of solvates of Li salts immobilized in a solid organic polymer matrix. In particular, this invention relates to Li batteries using solid polymer electrolytes derived by immobilizing solvates formed between a Li salt and an aprotic organic solvent (or mixture of such solvents) in poly(vinyl chloride).

Internally plasticised cellulose polymers

International Nuclear Information System (INIS)

Burnup, M.; Hayes, G.F.; Fydelor, P.J.

1981-01-01

Plasticised cellulose polymers comprise base polymer having a chain of β-anhydroglucose units joined by ether linkages, with at least one of said units carrying at least one chemically unreactive side chain derived from an allylic monomer or a vinyl substituted derivative of ferrocene. The side chains are normally formed by radiation grafting. These internally plasticised celluloses are useful in particular as inhibitor coatings for rocket motor propellants and in general wherever cellulose polymers are employed. (author)

Sustainable pyrolytic sludge-char preparation on improvement of closed-loop sewage sludge treatment: Characterization and combined in-situ application.

Science.gov (United States)

Jin, Zhengyu; Chang, Fengmin; Meng, Fanlin; Wang, Cuiping; Meng, Yao; Liu, Xiaoji; Wu, Jing; Zuo, Jiane; Wang, Kaijun

2017-10-01

Aiming at closed-loop sustainable sewage sludge treatment, an optimal and economical pyrolytic temperature was found at 400-450 °C considering its pyrolysis efficiency of 65%, fast cracking of hydrocarbons, proteins and lipids and development of aromatized porous structure. Fourier-transform infrared (FTIR) and X-ray diffraction (XRD) tests demonstrated the development of adsorptive functional groups and crystallographic phases of adsorptive minerals. The optimal sludge-char, with a medium specific surface area of 39.6 m 2  g -1 and an iodine number of 327 mgI 2 g -1 , performed low heavy metals lixiviation. The application of sludge-char in raw sewage could remove 30% of soluble chemical oxygen demand (SCOD), along with an acetic acid adsorption capacity of 18.0 mg g -1 . The developed mesopore and/or macropore structures, containing rich acidic and basic functional groups, led to good biofilm matrices for enhanced microbial activities and improved autotrophic nitrification in anoxic stage of an A/O reactor through adsorbed extra carbon source, and hence achieved the total nitrogen (TN) removal up to 50.3%. It is demonstrated that the closed-loop sewage sludge treatment that incorporates pyrolytic sludge-char into in-situ biological sewage treatment can be a promising sustainable strategy by further optimization. Copyright © 2017 Elsevier Ltd. All rights reserved.

Are forestation, bio-char and landfilled biomass adequate offsets for the climate effects of burning fossil fuels?

NARCIS (Netherlands)

Reijnders, L.

2009-01-01

Forestation and landfilling purpose-grown biomass are not adequate offsets for the CO2 emission from burning fossil fuels. Their permanence is insufficiently guaranteed and landfilling purpose-grown biomass may even be counterproductive. As to permanence, bio-char may do better than forests or

Small angle neutron scattering form polymer melts: structural investigation and phase behaviour

International Nuclear Information System (INIS)

Ertugrul, O.

2004-01-01

The Small-Angle Neutron Scattering (SANS) techniques have been used to study the structural properties and phase behavior of polymer melts. A model based on Random Phase Approximation (RPA) is proposed to predict the experimental data. By fitting the model to data we could be able to obtain radius of gyration (a measure of size of a polymer) and phase transition for the sample. (author)

Char crystalline transformations during coal combustion and their implications for carbon burnout

Energy Technology Data Exchange (ETDEWEB)

Hurt, R.H.

1999-03-11

Residual, or unburned carbon in fly ash affects many aspects of power plant performance and economy including boiler efficiency, electrostatic precipitator operation, and ash as a salable byproduct. There is a large concern in industry on the unburned carbon problem due to a variety of factors, including low-NOx combustion system and internationalization of the coal market. In recent work, it has been found that residual carbon extracted from fly ash is much less reactive than the laboratory chars on which the current kinetics are based. It has been suggested that thermal deactivation at the peak temperature in combustion is a likely phenomenon and that the structural ordering is one key mechanism. The general phenomenon of carbon thermal annealing is well known, but there is a critical need for more data on the temperature and time scale of interest to combustion. In addition, high resolution transmission electron microscopy (HRTEM) fringe imaging, which provides a wealth of information on the nature and degree of crystallinity in carbon materials such as coal chars, has become available. Motivated by these new developments, this University Coal Research project has been initiated with the following goals: to determine transient, high-temperature, thermal deactivation kinetics as a function of parent coal and temperature history; and to characterize the effect of this thermal treatment on carbon crystalline structure through high-resolution transmission electron microscopy and specialized, quantitative image analysis.

Char crystalline transformations during coal combustion and their implications for carbon burnout

Energy Technology Data Exchange (ETDEWEB)

Hurt, R.H.

1999-07-07

Residual, or unburned carbon in fly ash affects many aspects of power plant performance and economy including boiler efficiency, electrostatic precipitator operation, and ash as a salable byproduct. There is a large concern in industry on the unburned carbon problem due to a variety of factors, including low-NOx combustion system and internationalization of the coal market. In recent work, it has been found that residual carbon extracted from fly ash is much less reactive than the laboratory chars on which the current kinetics are based. It has been suggested that thermal deactivation at the peak temperature in combustion is a likely phenomenon and that the structural ordering is one key mechanism. The general phenomenon of carbon thermal annealing is well known, but there is a critical need for more data on the temperature and time scale of interest to combustion. In addition, high resolution transmission electron microscopy (HRTEM) fringe imaging, which provides a wealth of information on the nature and degree of crystallinity in carbon materials such as coal chars, has become available. Motivated by these new developments, this University Coal Research project has been initiated with the following goals: (1) To determine transient, high-temperature, thermal deactivation kinetics as a function of parent coal and temperature history. (2) To characterize the effect of the thermal treatment on carbon crystalline structure through high-resolution transmission electron microscopy and specialized, quantitative image analysis.

Characterization of coal and char reactivity as a function of burn-off

Energy Technology Data Exchange (ETDEWEB)

Biede, O.; Swane Lund, J. [DTU, Dept. of Energy Engineering (Denmark); Holst Soerensen, L. [Risoe National Lab. (Denmark); Peck, R.E. [Arizona State University (United States)

1996-12-01

Four coal types have been tested under varying burning conditions in three high-temperature experimental facilities: A 1.3 MW test furnace, an entrained flow reactor and a down-fired tube furnace with a flat flame burner have been used to produce char samples. More than one hundred partly burned samples with burn-off from 30% to 99% have been collected from the experimental facilities, and analyzed in a thermogravimetric analyser (TGA) giving, besides the proximate data, a char burning profile of each individual sample, using a linear TGA-temperature ramp of 3 deg. C/minute. The burning profile derived by this procedure agrees well with reactivity profiles derived at a constant temperature. It is shown that small particle burn faster than large particles, and that small particles in general are more reactive than large particles. Particles burn faster when the oxygen partial pressure is increased, and apparently the oxygen partial pressure influences the combustion rate differently for different coal types. Except for one coal type, that apparently behaves differently in different burning environments, the ranking with respect to reactivity among the coals remains consistent at both high and at low temperatures. It is further shown how samples from one coal type varies more in behavior than samples from the other coal types, indicating a larger inhomogeneity of this coal. In general the reactivity of collected samples decrease with high-temperature burn-off. (au) 20 refs.

Gel polymer electrolytes for batteries

Science.gov (United States)

Balsara, Nitash Pervez; Eitouni, Hany Basam; Gur, Ilan; Singh, Mohit; Hudson, William

2014-11-18

Nanostructured gel polymer electrolytes that have both high ionic conductivity and high mechanical strength are disclosed. The electrolytes have at least two domains--one domain contains an ionically-conductive gel polymer and the other domain contains a rigid polymer that provides structure for the electrolyte. The domains are formed by block copolymers. The first block provides a polymer matrix that may or may not be conductive on by itself, but that can soak up a liquid electrolyte, thereby making a gel. An exemplary nanostructured gel polymer electrolyte has an ionic conductivity of at least 1.times.10.sup.-4 S cm.sup.-1 at 25.degree. C.

Small angle scattering and polymers

International Nuclear Information System (INIS)

Cotton, J.P.

1996-01-01

The determination of polymer structure is a problem of interest for both statistical physics and industrial applications. The average polymer structure is defined. Then, it is shown why small angle scattering, associated with isotopic substitution, is very well suited to the measurement of the chain conformation. The corresponding example is the old, but pedagogic, measurement of the chain form factor in the polymer melt. The powerful contrast variation method is illustrated by a recent determination of the concentration profile of a polymer interface. (author) 12 figs., 48 refs

Wear of polymers and composites

CERN Document Server

Abdelbary, Ahmed

2015-01-01

In the field of tribology, the wear behaviour of polymers and composite materials is considered a highly non-linear phenomenon. Wear of Polymers and Composites introduces fundamentals of polymers and composites tribology. The book suggests a new approach to explore the effect of applied load and surface defects on the fatigue wear behaviour of polymers, using a new tribometer and thorough experiments. It discusses effects of surface cracks, under different static and cyclic loading parameters on wear, and presents an intelligent algorithm, in the form of a neural network, to map the relations

Oriented nanofibers embedded in a polymer matrix

Science.gov (United States)

Barrera, Enrique V. (Inventor); Lozano, Karen (Inventor); Rodriguez-Macias, Fernando J. (Inventor); Chibante, Luis Paulo Felipe (Inventor); Stewart, David Harris (Inventor)

2011-01-01

A method of forming a composite of embedded nanofibers in a polymer matrix is disclosed. The method includes incorporating nanofibers in a plastic matrix forming agglomerates, and uniformly distributing the nanofibers by exposing the agglomerates to hydrodynamic stresses. The hydrodynamic said stresses force the agglomerates to break apart. In combination or additionally elongational flow is used to achieve small diameters and alignment. A nanofiber reinforced polymer composite system is disclosed. The system includes a plurality of nanofibers that are embedded in polymer matrices in micron size fibers. A method for producing nanotube continuous fibers is disclosed. Nanofibers are fibrils with diameters of 100 nm, multiwall nanotubes, single wall nanotubes and their various functionalized and derivatized forms. The method includes mixing a nanofiber in a polymer; and inducing an orientation of the nanofibers that enables the nanofibers to be used to enhance mechanical, thermal and electrical properties. Orientation is induced by high shear mixing and elongational flow, singly or in combination. The polymer may be removed from said nanofibers, leaving micron size fibers of aligned nanofibers.

Effect of sewage sledge and their bio-char on some soil qualities in Second year cropping

Science.gov (United States)

fathi dokht, hamed; Movahedi Naeini, Seyed Alireza; Dordipor, Esmaeil; mirzanejad, moujan

2016-04-01

Bio char (BC) application as a soil amendment has achieved much interest and has been found that considerably improves soil nutrient status and crop yields on poor soils. However, information on the effect of BC on illitic soils in temperate climates is still insufficient. The primary objective in this study was to assess the influence of sewage sledge and their bio-char on the soil physical properties, nutrient status and plant production in Second year cropping. The result may also provide a reference for the use of biochars as a solution in agricultural waste management when sludge with considerable load of pathogens are involved. Soybean was already grown one year and will be repeated one more year with same treatments. The investigated soil properties included soil water content and mechanical resistance, pH, electrical conductivity (EC), calcium- acetate-lactate (CAL)-extractable P (PCAL) and K (KCAL), C, N, and nitrogen-supplying potential (NSP). The results show soil water content, potassium uptake and plant yield were increased. Heating sludge removed all pathogens and soybean yield was increased by 7%.

Water Soluble Polymers for Pharmaceutical Applications

Directory of Open Access Journals (Sweden)

Veeran Gowda Kadajji

2011-11-01

Full Text Available Advances in polymer science have led to the development of novel drug delivery systems. Some polymers are obtained from natural resources and then chemically modified for various applications, while others are chemically synthesized and used. A large number of natural and synthetic polymers are available. In the present paper, only water soluble polymers are described. They have been explained in two categories (1 synthetic and (2 natural. Drug polymer conjugates, block copolymers, hydrogels and other water soluble drug polymer complexes have also been explained. The general properties and applications of different water soluble polymers in the formulation of different dosage forms, novel delivery systems and biomedical applications will be discussed.

Single point incremental forming: Formability of PC sheets

Science.gov (United States)

Formisano, A.; Boccarusso, L.; Carrino, L.; Lambiase, F.; Minutolo, F. Memola Capece

2018-05-01

Recent research on Single Point Incremental Forming of polymers has slightly covered the possibility of expanding the materials capability window of this flexible forming process beyond metals, by demonstrating the workability of thermoplastic polymers at room temperature. Given the different behaviour of polymers compared to metals, different aspects need to be deepened to better understand the behaviour of these materials when incrementally formed. Thus, the aim of the work is to investigate the formability of incrementally formed polycarbonate thin sheets. To this end, an experimental investigation at room temperature was conducted involving formability tests; varying wall angle cone and pyramid frusta were manufactured by processing polycarbonate sheets with different thicknesses and using tools with different diameters, in order to draw conclusions on the formability of polymer sheets through the evaluation of the forming angles and the observation of the failure mechanisms.

Slippery self-lubricating polymer surfaces

Science.gov (United States)

Aizenberg, Joanna; Aizenberg, Michael; Cui, Jiaxi; Dunn, Stuart; Hatton, Benjamin; Howell, Caitlin; Kim, Philseok; Wong, Tak Sing; Yao, Xi

2018-05-08

The present disclosure describes a strategy to create self-healing, slippery self-lubricating polymers. Lubricating liquids with affinities to polymers can be utilized to get absorbed within the polymer and form a lubricant layer (of the lubricating liquid) on the polymer. The lubricant layer can repel a wide range of materials, including simple and complex fluids (water, hydrocarbons, crude oil and bodily fluids), restore liquid-repellency after physical damage, and resist ice, microorganisms and insects adhesion. Some exemplary applications where self-lubricating polymers will be useful include energy-efficient, friction-reduction fluid handling and transportation, medical devices, anti-icing, optical sensing, and as self-cleaning, and anti-fouling materials operating in extreme environments.

Inclusion and Functionalization of Polymers with Cyclodextrins: Current Applications and Future Prospects

Directory of Open Access Journals (Sweden)

Christian Folch-Cano

2014-09-01

Full Text Available The numerous hydroxyl groups available in cyclodextrins are active sites that can form different types of linkages. They can be crosslinked with one another, or they can be derivatized to produce monomers that can form linear or branched networks. Moreover, they can form inclusion complexes with polymers and different substrates, modifying their physicochemical properties. This review shows the different applications using polymers with cyclodextrins, either by forming inclusion complexes, ternary complexes, networks, or molecularly imprinted polymers (MIPs. On one hand, the use of cyclodextrins enhances the properties of each polymer, and on the other the use of polymers decreases the amount of cyclodextrins required in different formulations. Both cyclodextrins and polymers contribute synergistically in several applications such as pharmacological, nutritional, environmental, and other industrial fields. The use of polymers based on cyclodextrins is a low cost easy to use potential tool with great future prospects.

The Research on Polymer Microcapsulation for Cell Technology

Institute of Scientific and Technical Information of China (English)

ZHANG Zhi-bin; LI Min; SONG Hong; FANG Yi; HUA Hui; CHEN Li-guo; ZHOU Wei; WANG Zheng-rong

2004-01-01

Microcapsulation is a technology that enwrapped the solid or liquid or some gas matter with membrane materials to form microparticles(i.e.microcapsules). The materials of microcapsule is composed of naturnal polymers or modified naturnal polymers or synthesized polymers. The water-soluble core matter can only use oil-soluble wall materials, and vice versa.Synthesized methods of polymer microcapsulesSynthesized methods with monomers as raw materialsThis kind of methods include suspension polymerization, emulsion polymerization, dispersal polymerization, precipitation polymerization,suspension condensation polymerization, dispersal condensation polymerization, deposition condensation polymerization, interface condensation polymerization, and so on.Synthesized methods with polymers as raw materialsThese methods are suspension cross-linked polymerization, coacervation phase separation,extraction with solvent evaporation, polymer deposition, polymer chelation, polymer gel,solidification of melting polymer, tray-painted ways, fluidized bed ways, and so forth.Polymer materials to synthesize microcapsules2.1. Naturnal polymer materialsThe characteristics of this kind of materials are easy to form membrane, good stability and no toxicity. The polymer materials include lipids(liposome), amyloses, proteins, plant gels, waxes, etc.2.2. Modified polymer materialsThe characteristics of these materials are little toxicity, high viscidity(viscosity), soluble salt materials. But they cannot be used in water, acidic environment and high temperature environment for a long time. The materials include all kind of derivants of celluloses.2.3. Synthesized polymer materialsThe characteristics of the materials are easy to form membrane, good stability and adjustment of membrane properties. The synthesized polymer materials include degradable polymers(PLA, PGA,PLGA, PCL, PHB, PHV, PHA, PEG, PPG and the like) and indegradable polymers(PA, PMMA,PAM, PS, PVC, PB, PE, PU, PUA, PVA and otherwise

Development of Polymer Blends in order to Toughening of Polymers: A review

Directory of Open Access Journals (Sweden)

Carlos Bruno Barreto Luna

2015-05-01

Full Text Available Polymers are materials of large use in the various sectors of the world economy. The use of polymeric materials in daily life, instead of the classic materials has increased in recent decades. However, for certain structural applications polymers need to get tougher. One of the principal toughening techniques based on physical mixture of two or more components, forming the so-called polymer blends. The addition of rubber or not vulcanized in polymer compositions is reported in the literature as a means of generating mixtures of easy processing, and economically advantageous to increase the toughness of the thermoplastic matrix of interest. Moreover, it can be an alternative for the recycling of waste tires and footwear coming from industries, as well reduce harmful effects on the environment. Therefore, the present study aims to present a review of the definitions, benefits, thermodynamic fundamentals and toughening polymers.

Inverse Heat Conduction Methods in the CHAR Code for Aerothermal Flight Data Reconstruction

Science.gov (United States)

Oliver, A. Brandon; Amar, Adam J.

2016-01-01

Reconstruction of flight aerothermal environments often requires the solution of an inverse heat transfer problem, which is an ill-posed problem of determining boundary conditions from discrete measurements in the interior of the domain. This paper will present the algorithms implemented in the CHAR code for use in reconstruction of EFT-1 flight data and future testing activities. Implementation details will be discussed, and alternative hybrid-methods that are permitted by the implementation will be described. Results will be presented for a number of problems.

Polymer based tunneling sensor

Science.gov (United States)

Cui, Tianhong (Inventor); Wang, Jing (Inventor); Zhao, Yongjun (Inventor)

2006-01-01

A process for fabricating a polymer based circuit by the following steps. A mold of a design is formed through a lithography process. The design is transferred to a polymer substrate through a hot embossing process. A metal layer is then deposited over at least part of said design and at least one electrical lead is connected to said metal layer.

Pad printing as a film forming technique for polymer solar cells

Energy Technology Data Exchange (ETDEWEB)

Krebs, Frederik C. [Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, Frederiksborgvej 399, DK-4000 Roskilde (Denmark)

2009-04-15

Pad printing as a technique for preparing the active layer in polymer solar cells is presented. The technique employs a silicone rubber stamp to pick up the motif from a gravure plate and transfer it to the substrate. The strengths and limitations of pad printing are discussed and polymer solar cells prepared by pad printing are presented. Devices were prepared on indium tin oxide substrates but in principle the entire photovoltaic device comprising front and back electrodes, barrier layers and active layer could be printed with no need for vacuum steps. The device geometry comprises a spin coated transparent zinc oxide front electrode, a pad printed active layer based on a bulk heterojunction of the thermocleavable polymer poly(3-(2-methylhexyloxycarbonyl)thiophene-co-thiopene) (P3MHOCT) and zinc oxide nanoparticles, spin coated PEDOT:PSS and finally a manually cast thermally cured silver paste back electrode. The P3MHOCT was converted to poly(3-carboxy-dithiophene) (P3CT) in situ by heating the film to 200 C for a brief period. The entire printing and device preparation was carried out in the ambient atmosphere and the devices obtained had a good stability in air during storage and operation. (author)

Size-dependent resource limitation and foraging-predation risk trade-offs: growth and habitat use in young arctic char

NARCIS (Netherlands)

Byström, P.; Andersson, J.; Persson, L.; de Roos, A.M.

2004-01-01

Variation in growth and habitat use is closely connected to individual responses to habitat specific resource levels and predation risk. In three mountain lakes which differed in the density of young-of-the-year (YOY) arctic char (Salvelinus alpinus), we studied the growth, diets and habitat use of

Size-dependent resource limitation and foraging-predation risk trade-offs:growth and habitat use in young artic char

NARCIS (Netherlands)

Bystrom, P.; Persson, L.; de Roos, A.M.; Andersson, J.A.

2004-01-01

Variation in growth and habitat use is closely connected to individual responses to habitat specific resource levels and predation risk. In three mountain lakes which differed in the density of young-of-the-year (YOY) arctic char (Salvelinus alpinus), we studied the growth, diets and habitat use of

Odor and VOC Emissions from Pan Frying of Mackerel at Three Stages: Raw, Well-Done, and Charred

Directory of Open Access Journals (Sweden)

Jeong-Hyeon Ahn

2014-11-01

Full Text Available Many classes of odorants and volatile organic compounds that are deleterious to our wellbeing can be emitted from diverse cooking activities. Once emitted, they can persist in our living space for varying durations. In this study, various volatile organic compounds released prior to and during the pan frying of fish (mackerel were analyzed at three different cooking stages (stage 1 = raw (R, stage 2 = well-done (W, and stage 3 = overcooked/charred (O. Generally, most volatile organic compounds recorded their highest concentration levels at stage 3 (O, e.g., 465 (trimethylamine and 106 ppb (acetic acid. In contrast, at stage 2 (W, the lowest volatile organic compounds emissions were observed. The overall results of this study confirm that trimethylamine is identified as the strongest odorous compound, especially prior to cooking (stage 1 (R and during overcooking leading to charring (stage 3 (O. As there is a paucity of research effort to measure odor intensities from pan frying of mackerel, this study will provide valuable information regarding the management of indoor air quality.

Immobilization of soil cadmium using combined amendments of illite/smectite clay with bone chars.

Science.gov (United States)

Li, Hong; Ou, Jieyong; Wang, Xuedong; Yan, Zengguang; Zhou, Youya

2018-05-12

The widespread use of cadmium (Cd)-containing organic fertilizers is a source of heavy metal inputs to agricultural soils in suburban areas. Therefore, the research and development of new materials and technologies for the remediation of Cd-contaminated soil is of great significance and has the potential to guarantee the safety of agricultural products and the protection of human health. We performed pot experiments to determine the potential of combined amendments of illite/smectite (I/S) clay with bone chars for the remediation of Cd-contaminated agricultural soils in a suburban area of Beijing, China. The results showed that both diethylene triamine pentaacetic acid (DTPA)-extractable Cd in soil and the Cd in Brassica chinensis were significantly decreased by the application of 1, 2, or 5% combined amendments with various I/S and bone char (BC) ratios. The higher proportions of BC used in the combined amendments resulted in a better immobilization of soil Cd. The application of the 5% amendment that combined I/S with either pig or cattle BC resulted in the best immobilization. All of the combined amendments, regardless of the composition and ratio of the components, had no negative effects on the growth of B. chinensis. Therefore, it was concluded that combined amendments of I/S and BC have a good potential for remediating Cd-contaminated soils.

Nanostructured polymer membranes for proton conduction

Science.gov (United States)

Balsara, Nitash Pervez; Park, Moon Jeong

2013-06-18

Polymers having an improved ability to entrain water are characterized, in some embodiments, by unusual humidity-induced phase transitions. The described polymers (e.g., hydrophilically functionalized block copolymers) have a disordered state and one or more ordered states (e.g., a lamellar state, a gyroid state, etc.). In one aspect, the polymers are capable of undergoing a disorder-to-order transition while the polymer is exposed to an increasing temperature at a constant relative humidity. In some aspects the polymer includes a plurality of portions, wherein a first portion forms proton-conductive channels within the membrane and wherein the channels have a width of less than about 6 nm. The described polymers are capable of entraining and preserving water at high temperature and low humidity. Surprisingly, in some embodiments, the polymers are capable of entraining greater amounts of water with the increase of temperature. The polymers can be used in Polymer Electrolyte Membranes in fuel cells.

17beta-estradiol induced vitellogenesis is inhibited by cortisol at the post-transcriptional level in Arctic char (Salvelinus alpinus

Directory of Open Access Journals (Sweden)

Modig Carina

2004-09-01

Full Text Available Abstract This study was performed to investigate stress effects on the synthesis of egg yolk precursor, vitellogenin (Vtg in Arctic char (Salvelinus alpinus. In particular the effect of cortisol (F was determined since this stress hormone has been suggested to interfere with vitellogenesis and is upregulated during sexual maturation in teleosts. Arctic char Vtg was purified and polyclonal antibodies were produced in order to develop tools to study regulation of vitellogenesis. The Vtg antibodies were used to develop an enzyme-linked immunosorbent assay. The corresponding Vtg cDNA was cloned from a hepatic cDNA library in order to obtain DNA probes to measure Vtg mRNA expression. Analysis of plasma from juvenile Arctic char, of both sexes, exposed to different steroids showed that production of Vtg was induced in a dose dependent fashion by 17β-estradiol (E2, estrone and estriol. Apart from estrogens a high dose of F also upregulated Vtg. In addition, F, progesterone (P and tamoxifen were tested to determine these compounds ability to modulate E2 induced Vtg synthesis at both the mRNA and protein level. Tamoxifen was found to inhibit E2 induced Vtg mRNA and protein upregulation. P did not alter the Vtg induction while F reduced the Vtg protein levels without affecting the Vtg mRNA levels. Furthermore the inhibition of Vtg protein was found to be dose dependent. Thus, the inhibitory effect of F on Vtg appears to be mediated at the post-transcriptional level.

Caracterização dos produtos líquidos e do carvão da pirólise de serragem de eucalipto Characterization of liquid products and char from the pyrolysis of eucalyptus sawdust

Directory of Open Access Journals (Sweden)

Ayrton F. Martins

2007-08-01

Full Text Available This study proposes the low temperature pyrolysis as an alternative conversion process for residual biomass and for obtaining gaseous, liquid and solid chemical feedstocks. Using a bench electrical pyrolysis oven, four product fractions from eucalyptus sawdust were obtained: a gaseous one, two liquid (aqueous and oily, and a solid residue (char. These products were characterized by different analytical methods. The liquid fractions showed themselves as potential sources for input chemicals. The residual char revealed appreciable adsorption capability. The process demonstrated good efficiency, generating at least two fractions of great industrial interest: bio oil and char.

Solid electrolyte material manufacturable by polymer processing methods

Science.gov (United States)

Singh, Mohit; Gur, Ilan; Eitouni, Hany Basam; Balsara, Nitash Pervez

2012-09-18

The present invention relates generally to electrolyte materials. According to an embodiment, the present invention provides for a solid polymer electrolyte material that is ionically conductive, mechanically robust, and can be formed into desirable shapes using conventional polymer processing methods. An exemplary polymer electrolyte material has an elastic modulus in excess of 1.times.10.sup.6 Pa at 90 degrees C. and is characterized by an ionic conductivity of at least 1.times.10.sup.-5 Scm-1 at 90 degrees C. An exemplary material can be characterized by a two domain or three domain material system. An exemplary material can include material components made of diblock polymers or triblock polymers. Many uses are contemplated for the solid polymer electrolyte materials. For example, the present invention can be applied to improve Li-based batteries by means of enabling higher energy density, better thermal and environmental stability, lower rates of self-discharge, enhanced safety, lower manufacturing costs, and novel form factors.

Preparing high-density polymer brushes by mechanically assisted polymer assembly (MAPA)

Science.gov (United States)

Wu, Tao; Efimenko, Kirill; Genzer, Jan

2001-03-01

We introduce a novel method of modifying the surface properties of materials. This technique, called MAPA (="mechanically assisted polymer assembly"), is based on: 1) chemically attaching polymerization initiators to the surface of an elastomeric network that has been previously stretched by a certain length, Δx, and 2) growing end-anchored macromolecules using surface initiated ("grafting from") atom transfer living radical polymerization. After the polymerization, the strain is removed from the substrate, which returns to its original size causing the grafted macromolecules to stretch away from the substrate and form a dense polymer brush. We demonstrate the feasibility of the MAPA method by preparing high-density polymer brushes of poly(acryl amide), PAAm. We show that, as expected, the grafting density of the PAAm brushes can be increased by increasing Δx. We demonstrate that polymer brushes with extremely high grafting densities can be successfully prepared by MAPA.

Synthetic Strategies in the Preparation of Polymer/Inorganic Hybrid Nanoparticles

Science.gov (United States)

Hood, Matthew A.; Mari, Margherita; Muñoz-Espí, Rafael

2014-01-01

This article reviews the recent advances and challenges in the preparation of polymer/inorganic hybrid nanoparticles. We mainly focus on synthetic strategies, basing our classification on whether the inorganic and the polymer components have been formed in situ or ex situ, of the hybrid material. Accordingly, four types of strategies are identified and described, referring to recent examples: (i) ex situ formation of the components and subsequent attachment or integration, either by covalent or noncovalent bonding; (ii) in situ polymerization in the presence of ex situ formed inorganic nanoparticles; (iii) in situ precipitation of the inorganic components on or in polymer structures; and (iv) strategies in which both polymer and inorganic component are simultaneously formed in situ. PMID:28788665

Claisen thermally rearranged (CTR) polymers

Science.gov (United States)

Tena, Alberto; Rangou, Sofia; Shishatskiy, Sergey; Filiz, Volkan; Abetz, Volker

2016-01-01

Thermally rearranged (TR) polymers, which are considered the next-generation of membrane materials because of their excellent transport properties and high thermal and chemical stability, are proven to have significant drawbacks because of the high temperature required for the rearrangement and low degree of conversion during this process. We demonstrate that using a [3,3]-sigmatropic rearrangement, the temperature required for the rearrangement of a solid glassy polymer was reduced by 200°C. Conversions of functionalized polyimide to polybenzoxazole of more than 97% were achieved. These highly mechanically stable polymers were almost five times more permeable and had more than two times higher degrees of conversion than the reference polymer treated under the same conditions. Properties of these second-generation TR polymers provide the possibility of preparing efficient polymer membranes in a form of, for example, thin-film composite membranes for various gas and liquid membrane separation applications. PMID:27482538

Direct Photopatterning of Electrochromic Polymers

DEFF Research Database (Denmark)

Jensen, Jacob; Dyer, Aubrey L.; Shen, D. Eric

2013-01-01

Propylenedioxythiophene (ProDOT) polymers are synthesized using an oxidative polymerization route that results in methacrylate substituted poly(ProDOTs) having a Mn of 10–20 kDa wherein the methacrylate functionality constitutes from 6 to 60% of the total monomer units. Solutions of these polymers...... show excellent film forming abilities, with thin films prepared using both spray‐casting and spin‐coating. These polymers are demonstrated to crosslink upon UV irradiation at 350 nm, in the presence of an appropriate photoinitiator, to render the films insoluble to common organic solvents....... Electrochemical, spectroelectrochemical, and colorimetric analyses of the crosslinked polymer films are performed to establish that they retain the same electrochromic qualities as the parent polymers with no detriment to the observed properties. To demonstrate applicability for multi‐film processing...

Energetic assessment of air-steam gasification of sewage sludge and of the integration of sewage sludge pyrolysis and air-steam gasification of char

International Nuclear Information System (INIS)

Gil-Lalaguna, N.; Sánchez, J.L.; Murillo, M.B.; Atienza-Martínez, M.; Gea, G.

2014-01-01

Thermo-chemical treatment of sewage sludge is an interesting option for recovering energy and/or valuable products from this waste. This work presents an energetic assessment of pyrolysis and gasification of sewage sludge, also considering the prior sewage sludge thermal drying and the gasification of the char derived from the pyrolysis stage. Experimental data obtained from pyrolysis of sewage sludge, gasification of sewage sludge and gasification of char (all of these performed in a lab-scale fluidized reactor) were used for the energetic calculations. The results show that the energy contained in the product gases from pyrolysis and char gasification is not enough to cover the high energy consumption for thermal drying of sewage sludge. Additional energy could be obtained from the calorific value of the pyrolysis liquid, but some of its properties must be improved facing towards its use as fuel. On the other hand, the energy contained in the product gas of sewage sludge gasification is enough to cover the energy demand for both the sewage sludge thermal drying and the gasification process itself. Furthermore, a theoretical study included in this work shows that the gasification efficiency is improved when the chemical equilibrium is reached in the process. - Highlights: • 4 MJ kg −1 for thermal drying of sewage sludge (SS) from 65 to 6.5 wt.% of moisture. • 0.15 MJ kg −1 for thermal decomposition of sewage sludge during fast pyrolysis. • Not enough energy in gases from SS pyrolysis and char gasification for thermal drying. • Enough energy in SS gasification gas for thermal drying and gasification process. • Gasification efficiency improves when equilibrium is reached in the process

Methods of enhancing conductivity of a polymer-ceramic composite electrolyte

Science.gov (United States)

Kumar, Binod

2003-12-02

Methods for enhancing conductivity of polymer-ceramic composite electrolytes are provided which include forming a polymer-ceramic composite electrolyte film by a melt casting technique and uniaxially stretching the film from about 5 to 15% in length. The polymer-ceramic composite electrolyte is also preferably annealed after stretching such that it has a room temperature conductivity of from 10.sup.-4 S cm.sup.-1 to 10.sup.-3 S cm.sup.-1. The polymer-ceramic composite electrolyte formed by the methods of the present invention may be used in lithium rechargeable batteries.

An integrated system for dissolution studies and magnetic resonance imaging of controlled release, polymer-based dosage forms-a tool for quantitative assessment of hydrogel formation processes.

Science.gov (United States)

Kulinowski, Piotr; Dorozyński, Przemysław; Jachowicz, Renata; Weglarz, Władysław P

2008-11-04

Controlled release (CR) dosage forms are often based on polymeric matrices, e.g., sustained-release tablets and capsules. It is crucial to visualise and quantify processes of the hydrogel formation during the standard dissolution study. A method for imaging of CR, polymer-based dosage forms during dissolution study in vitro is presented. Imaging was performed in a non-invasive way by means of the magnetic resonance imaging (MRI). This study was designed to simulate in vivo conditions regarding temperature, volume, state and composition of dissolution media. Two formulations of hydrodynamically balanced systems (HBS) were chosen as model CR dosage forms. HBS release active substance in stomach while floating on the surface of the gastric content. Time evolutions of the diffusion region, hydrogel formation region and "dry core" region were obtained during a dissolution study of L-dopa as a model drug in two simulated gastric fluids (i.e. in fed and fasted state). This method seems to be a very promising tool for examining properties of new formulations of CR, polymer-based dosage forms or for comparison of generic and originator dosage forms before carrying out bioequivalence studies.

Cementation of nuclear graphite using geo-polymers

International Nuclear Information System (INIS)

Girke, N.A.; Steinmetz, H.J.; Bukaemsky, A.; Bosbach, D.; Hermann, E.; Griebel, I.

2012-01-01

Geo-polymers are solid aluminosilicate materials usually formed by alkali hydroxide or alkali silicate activation of solid precursors such as coal fly ash, calcined clay and/or metallurgical slag. Today the primary application of geo-polymer technology is in the development of alternatives to Portland-based cements. Variations in the ratio of aluminium to silicon, and alkali to silicon or addition of structure support, produce geo-polymers with different physical and mechanical properties. These materials have an amorphous three-dimensional structure that gives geo-polymers certain properties, such as fire and acid resistance, low leach rate, which make them an ideal substitute for ordinary Portland cement (OPC) in a wide range of applications especially in conditioning and storage of radioactive waste. Therefore investigations have been initiated about how and to which amount graphite as a hydrophobic material can be mixed with cement or concrete to form stable waste products and which concretes fulfill the specifications at best. As result geo-polymers have been identified as a promising matrix for graphite containing nuclear wastes. With geo-polymers both favorable properties in the cementation process and a high long time structural stability of the products can be achieved. (authors)

Polymer hydrogels as optimized delivery systems

International Nuclear Information System (INIS)

Batista, Jorge G.S.; Varca, Gustavo H.C.; Ferraz, Caroline C.; Garrido, Gabriela P.; Diniz, Bruna M.; Carvalho, Vinicius S.; Lugao, Ademar B.

2013-01-01

Hydrogels are formed by polymers capable of absorbing large quantities of water. They consist of one or more three-dimensionally structured polymer networks formed by macromolecular chains linked by covalent bonds-crosslinks - and physical interactions. The application of hydrogels, has been widely studied. Biodegradable synthetic or natural polymers such as chitosan, starch and poly-lactic-co-glycolic acid, have properties that allow the development of biodegradable systems for drug and nutraceutics delivery. This study aimed to develop polymeric hydrogels based on polyvinyl alcohol, polyacrylamide and polyvinylpyrrolidone using ionizing radiation in order to develop hydrogels for improved loading and release of compounds. Polymer solutions were solubilized in water and poured into thermoformed packages. After sealing, the material was subjected to γ-irradiation at 25kGy. The samples were assayed by means of mechanical properties, gel fraction and swelling degree. Nanostructure characterization was performed using Flory's equation to determine crosslinking density. The systems developed showed swelling degree and adequate mechanical resistance. The nanostructure evaluation showed different results for each system demonstrating the need of choosing the polymer based on the specific properties of each material. (author)

Polymer hydrogels as optimized delivery systems

Energy Technology Data Exchange (ETDEWEB)

Batista, Jorge G.S.; Varca, Gustavo H.C.; Ferraz, Caroline C.; Garrido, Gabriela P.; Diniz, Bruna M.; Carvalho, Vinicius S.; Lugao, Ademar B., E-mail: jorgegabriel@usp.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2013-07-01

Hydrogels are formed by polymers capable of absorbing large quantities of water. They consist of one or more three-dimensionally structured polymer networks formed by macromolecular chains linked by covalent bonds-crosslinks - and physical interactions. The application of hydrogels, has been widely studied. Biodegradable synthetic or natural polymers such as chitosan, starch and poly-lactic-co-glycolic acid, have properties that allow the development of biodegradable systems for drug and nutraceutics delivery. This study aimed to develop polymeric hydrogels based on polyvinyl alcohol, polyacrylamide and polyvinylpyrrolidone using ionizing radiation in order to develop hydrogels for improved loading and release of compounds. Polymer solutions were solubilized in water and poured into thermoformed packages. After sealing, the material was subjected to γ-irradiation at 25kGy. The samples were assayed by means of mechanical properties, gel fraction and swelling degree. Nanostructure characterization was performed using Flory's equation to determine crosslinking density. The systems developed showed swelling degree and adequate mechanical resistance. The nanostructure evaluation showed different results for each system demonstrating the need of choosing the polymer based on the specific properties of each material. (author)

Binary Polymer Brushes of Strongly Immiscible Polymers.

Science.gov (United States)

Chu, Elza; Babar, Tashnia; Bruist, Michael F; Sidorenko, Alexander

2015-06-17

The phenomenon of microphase separation is an example of self-assembly in soft matter and has been observed in block copolymers (BCPs) and similar materials (i.e., supramolecular assemblies (SMAs) and homo/block copolymer blends (HBCs)). In this study, we use microphase separation to construct responsive polymer brushes that collapse to generate periodic surfaces. This is achieved by a chemical reaction between the minor block (10%, poly(4-vinylpyridine)) of the block copolymer and a substrate. The major block of polystyrene (PS) forms mosaic-like arrays of grafted patches that are 10-20 nm in size. Depending on the nature of the assembly (SMA, HBC, or neat BCP) and annealing method (exposure to vapors of different solvents or heating above the glass transition temperature), a range of "mosaic" brushes with different parameters can be obtained. Successive grafting of a secondary polymer (polyacrylamide, PAAm) results in the fabrication of binary polymer brushes (BPBs). Upon being exposed to specific selective solvents, BPBs may adopt different conformations. The surface tension and adhesion of the binary brush are governed by the polymer occupying the top stratum. The "mosaic" brush approach allows for a combination of strongly immiscible polymers in one brush. This facilitates substantial contrast in the surface properties upon switching, previously only possible for substrates composed of predetermined nanostructures. We also demonstrate a possible application of such PS/PAAm brushes in a tunable bioadhesion-bioadhesive (PS on top) or nonbioadhesive (PAAm on top) surface as revealed by Escherichia coli bacterial seeding.

The removal of reactive dyes using high-ash char

Directory of Open Access Journals (Sweden)

Moreira R.F.P.M.

2001-01-01

Full Text Available The thermodynamics and kinetics of adsorption of reactive dyes on high-ash char was studied. Equilibrium data were obtained using the static method with controlled agitation at temperatures in the range of 30 to 60ºC. The Langmuir isotherm model was used to describe the equilibrium of adsorption, and the equilibrium parameters, R L, in the range of 0 to 1 indicate favorable adsorption. The amount of dye adsorbed increased as temperature increased from 30 to 40ºC, but above 40ºC the increase in temperature resulted in a decrease in the amount of dye adsorbed. The kinetic data presented are for controlled agitation at 50 rpm and constant temperature with dye concentrations in the range of 10 ppm to50 ppm. The film mass transfer coefficient, Kf, and the effective diffusivity inside the particle, De, were fitted to the experimental data. The results indicate that internal diffusion governs the adsorption rate.

Bis-polymer lipid-peptide conjugates and nanoparticles thereof

Energy Technology Data Exchange (ETDEWEB)

Xu, Ting; Dong, He; Shu, Jessica; Dube, Nikhil

2018-04-24

The present invention provides bis-polymer lipid-peptide conjugates containing a hydrophobic block and headgroup containing a helical peptide and two polymer blocks. The conjugates can self-assemble to form helix bundle subunits, which in turn assemble to provide micellar nanocarriers for drug cargos and other agents. Particles containing the conjugates and methods for forming the particles are also disclosed.

Polymer sol-gel composite inverse opal structures.

Science.gov (United States)

Zhang, Xiaoran; Blanchard, G J

2015-03-25

We report on the formation of composite inverse opal structures where the matrix used to form the inverse opal contains both silica, formed using sol-gel chemistry, and poly(ethylene glycol), PEG. We find that the morphology of the inverse opal structure depends on both the amount of PEG incorporated into the matrix and its molecular weight. The extent of organization in the inverse opal structure, which is characterized by scanning electron microscopy and optical reflectance data, is mediated by the chemical bonding interactions between the silica and PEG constituents in the hybrid matrix. Both polymer chain terminus Si-O-C bonding and hydrogen bonding between the polymer backbone oxygens and silanol functionalities can contribute, with the polymer mediating the extent to which Si-O-Si bonds can form within the silica regions of the matrix due to hydrogen-bonding interactions.

Adsorption of Cr (III from aqueous solution by two forms of a superabsorbant polymer : parametric study and effect of activation mode

Directory of Open Access Journals (Sweden)

Ouass A.

2018-01-01

Full Text Available The adsorption of chromium ions Cr3+ using two forms of a superabsorbant polymer PANa from aqueous solution was investigated. On one hand the equilibrium pH with the distilled water and the pH of point of zero charge have been studied in order to characterize the acid-base behavior of both of PANa forms. On the other hand, the effect of contact time between PANa and the metallic solution and stirring speed of aqueous solution on the adsorption rate were established to highlight the importance of PANa as an efficient adsorbent of chromium ions Cr3+.

Species interactions and response time to climate change: ice-cover and terrestrial run-off shaping Arctic char and brown trout competitive asymmetries

Science.gov (United States)

Finstad, A. G.; Palm Helland, I.; Jonsson, B.; Forseth, T.; Foldvik, A.; Hessen, D. O.; Hendrichsen, D. K.; Berg, O. K.; Ulvan, E.; Ugedal, O.

2011-12-01

There has been a growing recognition that single species responses to climate change often mainly are driven by interaction with other organisms and single species studies therefore not are sufficient to recognize and project ecological climate change impacts. Here, we study how performance, relative abundance and the distribution of two common Arctic and sub-Arctic freshwater fishes (brown trout and Arctic char) are driven by competitive interactions. The interactions are modified both by direct climatic effects on temperature and ice-cover, and indirectly through climate forcing of terrestrial vegetation pattern and associated carbon and nutrient run-off. We first use laboratory studies to show that Arctic char, which is the world's most northernmost distributed freshwater fish, outperform trout under low light levels and also have comparable higher growth efficiency. Corresponding to this, a combination of time series and time-for-space analyses show that ice-cover duration and carbon and nutrient load mediated by catchment vegetation properties strongly affected the outcome of the competition and likely drive the species distribution pattern through competitive exclusion. In brief, while shorter ice-cover period and decreased carbon load favored brown trout, increased ice-cover period and increased carbon load favored Arctic char. Length of ice-covered period and export of allochthonous material from catchments are major, but contrasting, climatic drivers of competitive interaction between these two freshwater lake top-predators. While projected climate change lead to decreased ice-cover, corresponding increase in forest and shrub cover amplify carbon and nutrient run-off. Although a likely outcome of future Arctic and sub-arctic climate scenarios are retractions of the Arctic char distribution area caused by competitive exclusion, the main drivers will act on different time scales. While ice-cover will change instantaneously with increasing temperature

Reaction of carbon tetrachloride with methane in a non-equilibrium plasma at atmospheric pressure, and characterisation of the polymer thus formed

Energy Technology Data Exchange (ETDEWEB)

Gaikwad, Vaibhav [Process Safety and Environment Protection Research Group, School of Engineering, The University of Newcastle, Callaghan, NSW 2308 (Australia); Kennedy, Eric, E-mail: Eric.Kennedy@newcastle.edu.au [Process Safety and Environment Protection Research Group, School of Engineering, The University of Newcastle, Callaghan, NSW 2308 (Australia); Mackie, John [Process Safety and Environment Protection Research Group, School of Engineering, The University of Newcastle, Callaghan, NSW 2308 (Australia); Holdsworth, Clovia [Centre for Organic Electronics, Chemistry Building, School of Environmental and Life Sciences, University of Newcastle, Callaghan, NSW 2308 (Australia); Molloy, Scott; Kundu, Sazal; Stockenhuber, Michael [Process Safety and Environment Protection Research Group, School of Engineering, The University of Newcastle, Callaghan, NSW 2308 (Australia); Dlugogorski, Bogdan [School of Engineering and Information Technology, Murdoch University, Murdoch, WA 6150 (Australia)

2014-09-15

Highlights: • CCl{sub 4} remediation using non-equilibrium plasma and non-oxidative conditions is proposed. • The reaction mechanism relies on experimental data and quantum chemical analysis. • Comprehensive mass balance for the reaction is provided. • CCl{sub 4} is converted to an environmentally benign and potentially useful polymer. • Characterisation of the polymer structure based on NMR and FTIR analyses is presented. - Abstract: In this paper we focus on the development of a methodology for treatment of carbon tetrachloride utilising a non-equilibrium plasma operating at atmospheric pressure, which is not singularly aimed at destroying carbon tetrachloride but rather at converting it to a non-hazardous, potentially valuable commodity. This method encompasses the reaction of carbon tetrachloride and methane, with argon as a carrier gas, in a quartz dielectric barrier discharge reactor. The reaction is performed under non-oxidative conditions. Possible pathways for formation of major products based on experimental results and supported by quantum chemical calculations are outlined in the paper. We elucidate important parameters such as carbon tetrachloride conversion, product distribution, mass balance and characterise the chlorinated polymer formed in the process.

Humification and nonhumification pathways of the organic matter stabilization in soil: A review

Science.gov (United States)

Semenov, V. M.; Tulina, A. S.; Semenova, N. A.; Ivannikova, L. A.

2013-04-01

Polymeric and supramolecular models of humic substances (HSs) are considered. It has been noted that the HSs in natural objects can simultaneously occur in the forms of macromolecular polymers and supramolecularly organized monomers; macromolecular polymers of HSs can have some properties of suprastructures or be associated into aggregates, and covalent bonds can be formed between the monomers of supramolecules. Mineral particles of soil act as catalysts in chemical reactions between individual compounds, sorbents of biomolecules, and a surface for self-assembling HSs. It is supposed that the combination of such physicochemical processes and phenomena in soil as cementation, charring, incrustation, occlusion, sedimentation, sorption, coagulation, flocculation, encapsulation, complexation, and intercalation, as well as the entrapment of macroorganic, particulate, and soluble organic substances in micropores, can be as important for the stabilization of organic matter as the interactions between biomolecules with the formation of HSs.

Measurements of Gasification Characteristics of Coal and Char in CO2-Rich Gas Flow by TG-DTA

Directory of Open Access Journals (Sweden)

Zhigang Li

2013-01-01

Full Text Available Pyrolysis, combustion, and gasification properties of pulverized coal and char in CO2-rich gas flow were investigated by using gravimetric-differential thermal analysis (TG-DTA with changing O2%, heating temperature gradient, and flow rate of CO2-rich gases provided. Together with TG-DTA, flue gas generated from the heated coal, such as CO, CO2, and hydrocarbons (HCs, was analyzed simultaneously on the heating process. The optimum O2% in CO2-rich gas for combustion and gasification of coal or char was discussed by analyzing flue gas with changing O2 from 0 to 5%. The experimental results indicate that O2% has an especially large effect on carbon oxidation at temperature less than 1100°C, and lower O2 concentration promotes gasification reaction by producing CO gas over 1100°C in temperature. The TG-DTA results with gas analyses have presented basic reference data that show the effects of O2 concentration and heating rate on coal physical and chemical behaviors for the expected technologies on coal gasification in CO2-rich gas and oxygen combustion and underground coal gasification.

Handbook of polymer nanocomposites processing, performance and application

CERN Document Server

Mohanty, Amar; Misra, Manjusri; Kar, Kamal K; Pandey, Jitendra; Rana, Sravendra; Takagi, Hitoshi; Nakagaito, Antonio; Kim, Hyun-Joong

Volume A forms one volume of a Handbook about Polymer Nanocomposites. In some 20 chapters the preparation, architecture, characterisation, properties and application of polymer nanocomposites are discussed by experts in their respective fields.

Preparation of micro-porous gel polymer for lithium ion polymer battery

International Nuclear Information System (INIS)

Kim, Je Young; Kim, Seok Koo; Lee, Seung-Jin; Lee, Sang Young; Lee, Hyang Mok; Ahn, Soonho

2004-01-01

We have developed a micro-porous gelling polymer layer which is formed on both the sides of support polyolefin separator with wet or dry processing technique. Morphologies of gel-coated layer are dependent on the compositions and process conditions, such as solvent/non-solvent combination and stretching ratios. The micro-porous gelling layer is used for the assembly of the lithium ion polymer battery of LG Chemical Ltd. The structure of battery is given elsewhere and the battery has excellent discharge performance with 94% of 2C discharge performance at room temperature

Thiol X Click Foldamers for Polymer Affinity

Science.gov (United States)

2016-06-24

polymers   e. Invention  of  a  novel,  robust,  and  ambient   polymerization ...efficiently   polymerized   to   moderate  sized   polymers  capable  of  forming  >>1012  sequence  distinct   polymers ... polymerization  of  nucleobase  appended   thiol-­‐ene  monomers.    Naturally,   the  average   composition  of  the  

Production in Pichia pastoris of complementary protein-based polymers with heterodimer-forming WW and PPxY domains.

Science.gov (United States)

Domeradzka, Natalia E; Werten, Marc W T; de Vries, Renko; de Wolf, Frits A

2016-06-10

Specific coupling of de novo designed recombinant protein polymers for the construction of precisely structured nanomaterials is of interest for applications in biomedicine, pharmaceutics and diagnostics. An attractive coupling strategy is to incorporate specifically interacting peptides into the genetic design of the protein polymers. An example of such interaction is the binding of particular proline-rich ligands by so-called WW-domains. In this study, we investigated whether these domains can be produced in the yeast Pichia pastoris as part of otherwise non-interacting protein polymers, and whether they bring about polymer coupling upon mixing. We constructed two variants of a highly hydrophilic protein-based polymer that differ only in their C-terminal extensions. One carries a C-terminal WW domain, and the other a C-terminal proline-rich ligand (PPxY). Both polymers were produced in P. pastoris with a purified protein yield of more than 2 g L(-1) of cell-free broth. The proline-rich module was found to be O-glycosylated, and uncommonly a large portion of the attached oligosaccharides was phosphorylated. Glycosylation was overcome by introducing a Ser → Ala mutation in the PPxY peptide. Tryptophan fluorescence monitored during titration of the polymer containing the WW domain with either the glycosylated or nonglycosylated PPxY-containing polymer revealed binding. The complementary polymers associated with a Kd of ~3 µM, regardless of glycosylation state of the PPxY domain. Binding was confirmed by isothermal titration calorimetry, with a Kd of ~9 µM. This article presents a blueprint for the production in P. pastoris of protein polymers that can be coupled using the noncovalent interaction between WW domains and proline-rich ligands. The availability of this highly specific coupling tool will hereafter allow us to construct various supramolecular structures and biomaterials.

Environmental Impacts of the Production and Application of Biochar - EuroChar Project

Science.gov (United States)

Rack, Mireille; Woods, Jeremy

2014-05-01

One of the potential benefits of biochar is carbon sequestration. To determine the overall net sequestration potential it is important to analyse the full supply chain, assessing both the direct and indirect emissions associated with the production and application of biochar. However, it is essential to also incorporate additional environmental impact categories to ensure the assessment of a more complete environmental impact profile. This paper uses a full life-cycle assessment (LCA) methodology to evaluate the results from the EuroChar, 'biochar for carbon sequestration and large-scale removal of GHG from the atmosphere', project. This EU Seventh Framework Programme project aims to investigate and reduce uncertainties around the impacts of, and opportunities for, biochar, and in particular explore possible pathways for its introduction into modern agricultural systems in Europe. The LCA methodology, according to the ISO standards, is applied to the project-specific supply chains to analyse the environmental impacts of biochar production and application. Two conversion technologies for the production of biochar are assessed, gasification and hydrothermal carbonization (HTC), in order to provide conversion efficiencies and emission factors for the biochar production component of the supply chain. The selected feedstocks include those derived from waste residues and dedicated crops. For the end use stage, various forms and methods for biochar application are considered. In addition to the Global Warming Potential category, other environmental impact categories are also included in the analysis. The resulting 'feedstock * conversion technology' matrix provides nine pathways for the production and application of biochar, which are applied as a representative basis for the scenario modelling. These scenarios have been developed in order to assess the feedstock and land availability in Europe for the production and application of biochar and to give an order of

Thermoresponsive AuNPs Stabilized by Pillararene-Containing Polymers.

Science.gov (United States)

Liao, Xiaojuan; Guo, Lei; Chang, Junxia; Liu, Sha; Xie, Meiran; Chen, Guosong

2015-08-01

Pillararene-containing thermoresponsive polymers are synthesized via reversible addition-fragmentation chain transfer polymerization using pillararene derivatives as the effective chain transfer agents for the first time. These polymers can self-assemble into micelles and form vesicles after guest molecules are added. Furthermore, such functional polymers can be further applied to prepare hybrid gold nanoparticles, which integrate the thermoresponsivity of polymers and molecular recognition of pillararenes. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Optimal synthesis of a Ni(II)-dimethylglyoxime ion-imprinted polymer ...

African Journals Online (AJOL)

A Ni(II)-dimethylglyoxime ion-imprinted polymer {Ni(II)-DMG IIP} was optimised by the uniform design experimental ... The bonds formed between the template and the functional monomers in ion- imprinted polymerisation reactions are weaker, non-covalent. (Arshady and Mosbach, 1981; ..... where the polymer did not form.

SANS from interpenetrating polymer networks

International Nuclear Information System (INIS)

Markotsis, M.G.; Burford, R.P.; Knott, R.B.; Australian Nuclear Science and Technology Organisation, Menai, NSW; Hanley, T.L.; CRC for Polymers,; Australian Nuclear Science and Technology Organisation, Menai, NSW; Papamanuel, N.

2003-01-01

Full text: Interpenetrating polymer networks (IPNs) have been formed by combining two polymeric systems in order to gain enhanced material properties. IPNs are a combination of two or more polymers in network form with one network polymerised and/or crosslinked in the immediate presence of the other(s).1 IPNs allow better blending of two or more crosslinked networks. In this study two sets of IPNs were produced and their microstructure studied using a variety of techniques including small angle neutron scattering (SANS). The first system combined a glassy polymer (polystyrene) with an elastomeric polymer (SBS) with the glassy polymer predominating, to give a high impact plastic. The second set of IPNs contained epichlorohydrin (CO) and nitrile rubber (NBR), and was formed in order to produce novel materials with enhanced chemical and gas barrier properties. In both cases if the phase mixing is optimised the probability of controlled morphologies and synergistic behaviour is increased. The PS/SBS IPNs were prepared using sequential polymerisation. The primary SBS network was thermally crosslinked, then the polystyrene network was polymerised and crosslinked using gamma irradiation to avoid possible thermal degradation of the butadiene segment of the SBS. Tough transparent systems were produced with no apparent thermal degradation of the polybutadiene segments. The epichlorohydrin/nitrile rubber IPNs were formed by simultaneous thermal crosslinking reactions. The epichlorohydrin network was formed using lead based crosslinker, while the nitrile rubber was crosslinked by peroxide methods. The use of two different crosslinking systems was employed in order to achieve independent crosslinking thus resulting in an IPN with minimal grafting between the component networks. SANS, Transmission electron microscopy (TEM), and atomic force microscopy (AFM) were used to examine the size and shape of the phase domains and investigate any variation with crosslinking level and

Self-folding graphene-polymer bilayers

Energy Technology Data Exchange (ETDEWEB)

Deng, Tao [Institute of Microelectronics, Tsinghua University, Beijing 100084 (China); Department of Chemical and Biomolecular Engineering, Johns Hopkins University, Baltimore, Maryland 21218 (United States); Yoon, ChangKyu [Department of Materials Science and Engineering, Johns Hopkins University, Baltimore, Maryland 21218 (United States); Jin, Qianru [Department of Chemical and Biomolecular Engineering, Johns Hopkins University, Baltimore, Maryland 21218 (United States); Li, Mingen [Department of Physics, Johns Hopkins University, Baltimore, Maryland 21218 (United States); Liu, Zewen [Institute of Microelectronics, Tsinghua University, Beijing 100084 (China); Gracias, David H., E-mail: dgracias@jhu.edu [Department of Materials Science and Engineering, Johns Hopkins University, Baltimore, Maryland 21218 (United States); Department of Chemical and Biomolecular Engineering, Johns Hopkins University, Baltimore, Maryland 21218 (United States)

2015-05-18

In order to incorporate the extraordinary intrinsic thermal, electrical, mechanical, and optical properties of graphene with three dimensional (3D) flexible substrates, we introduce a solvent-driven self-folding approach using graphene-polymer bilayers. A polymer (SU-8) film was spin coated atop chemically vapor deposited graphene films on wafer substrates and graphene-polymer bilayers were patterned with or without metal electrodes using photolithography, thin film deposition, and etching. After patterning, the bilayers were released from the substrates and they self-folded to form fully integrated, curved, and folded structures. In contrast to planar graphene sensors on rigid substrates, we assembled curved and folded sensors that are flexible and they feature smaller form factors due to their 3D geometry and large surface areas due to their multiple rolled architectures. We believe that this approach could be used to assemble a range of high performance 3D electronic and optical devices of relevance to sensing, diagnostics, wearables, and energy harvesting.

Self-motion and the α-relaxation in glass-forming polymers. Molecular dynamic simulation and quasielastic neutron scattering results in polyisoprene

International Nuclear Information System (INIS)

Colmenero, Juan; Arbe, Arantxa; Alvarez, Fernando; Monkenbusch, Michael; Richter, Dieter; Farago, Bela; Frick, Bernhard

2003-01-01

The momentum transfer dependence of the self-motion of main chain hydrogens in the α-relaxation regime of a glass forming polymer, polyisoprene, has been thoroughly investigated by a combined effort involving fully atomistic molecular dynamic simulations and quasielastic neutron scattering measurements. In this way, we have established the existence of a crossover from a Gaussian regime of sublinear diffusion to a strongly non-Gaussian regime at short distances. We show that an anomalous jump diffusion model with a distribution of jump lengths gives rise to such a crossover. This model leads to a time-dependent non-Gaussian parameter exhibiting all features revealed so far from various simulations of different glass forming systems

Coherent states field theory in supramolecular polymer physics

Science.gov (United States)

Fredrickson, Glenn H.; Delaney, Kris T.

2018-05-01

In 1970, Edwards and Freed presented an elegant representation of interacting branched polymers that resembles the coherent states (CS) formulation of second-quantized field theory. This CS polymer field theory has been largely overlooked during the intervening period in favor of more conventional "auxiliary field" (AF) interacting polymer representations that form the basis of modern self-consistent field theory (SCFT) and field-theoretic simulation approaches. Here we argue that the CS representation provides a simpler and computationally more efficient framework than the AF approach for broad classes of reversibly bonding polymers encountered in supramolecular polymer science. The CS formalism is reviewed, initially for a simple homopolymer solution, and then extended to supramolecular polymers capable of forming reversible linkages and networks. In the context of the Edwards model of a non-reacting homopolymer solution and one and two-component models of telechelic reacting polymers, we discuss the structure of CS mean-field theory, including the equivalence to SCFT, and show how weak-amplitude expansions (random phase approximations) can be readily developed without explicit enumeration of all reaction products in a mixture. We further illustrate how to analyze CS field theories beyond SCFT at the level of Gaussian field fluctuations and provide a perspective on direct numerical simulations using a recently developed complex Langevin technique.

STEREO PHOTO HYDROFEL, A PROCESS OF MAKING SAID STEREO PHOTO HYDROGEL, POLYMERS FOR USE IN MAKING SUCH HYDROGEL AND A PHARMACEUTICAL COMPRISING SAID POLYMERS

NARCIS (Netherlands)

Hiemstra, C.; Zhong, Zhiyuan; Feijen, Jan

2008-01-01

The Invention relates to a stereo photo hydrogel formed by stereo complexed and photo cross-linked polymers, which polymers comprise at least two types of polymers having at least one hydrophilic component, at least one hydrophobic mutually stereo complexing component, and at least one of the types

A novel surface modification technique for forming porous polymer monoliths in poly(dimethylsiloxane).

Science.gov (United States)

Burke, Jeffrey M; Smela, Elisabeth

2012-03-01

A new method of surface modification is described for enabling the in situ formation of homogenous porous polymer monoliths (PPMs) within poly(dimethylsiloxane) (PDMS) microfluidic channels that uses 365 nm UV illumination for polymerization. Porous polymer monolith formation in PDMS can be challenging because PDMS readily absorbs the monomers and solvents, changing the final monolith morphology, and because PDMS absorbs oxygen, which inhibits free-radical polymerization. The new approach is based on sequentially absorbing a non-hydrogen-abstracting photoinitiator and the monomers methyl methacrylate and ethylene diacrylate within the walls of the microchannel, and then polymerizing the surface treatment polymer within the PDMS, entangled with it but not covalently bound. Four different monolith compositions were tested, all of which yielded monoliths that were securely anchored and could withstand pressures exceeding the bonding strength of PDMS (40 psi) without dislodging. One was a recipe that was optimized to give a larger average pore size, required for low back pressure. This monolith was used to concentrate and subsequently mechanical lyse B lymphocytes.

Microstructural aspects in steel fiber reinforced acrylic emulsion polymer modified concrete

Science.gov (United States)

Hazimmah, Dayang; Ayob, Afizah; Sie Yee, Lau; Chee Cung, Wong

2018-03-01

Scanning electron microscope observations of polymer-free and polymer-modified cements have shown that the polymer particles are partitioned between the inside of hydrates and the surface of anhydrous cement grains. For optimum dosage of acrylic emulsion polymer with 2.5%, the C-S-H gel in this structure is finer and more acicular. Some polymer adheres or deposit on the surface of the C-S-H gel. The presence of acrylic emulsion polymer confines the ionic diffusion so that the Ca(OH)2 crystallized locally to form fine crystals. The void in the structures seems to be smaller but no polymer films appears to be bridging the walls of pores although many polymer bonds or C-S-H spread into the pore spaces. In addition to porosity reduction, acrylic emulsion polymer modified the hydration products in the steel fiber -matrix ITZ. The hydration product C-S-H appeared as a needle like shape. The needle-shaped C-S-H increases and gradually formed the gel, with needles growing into the pore space. The phenomenon is more obvious as curing age increased.

Synthetic approaches to uniform polymers.

Science.gov (United States)

Ali, Monzur; Brocchini, Steve

2006-12-30

Uniform polymers are characterised by a narrow molecular weight distribution (MWD). Uniformity is also defined by chemical structure in respect of (1) monomer orientation, sequence and stereo-regularity, (2) polymer shape and morphology and (3) chemical functionality. The function of natural polymers such as polypeptides and polynucleotides is related to their conformational structure (e.g. folded tertiary structure). This is only possible because of their high degree of uniformity. While completely uniform synthetic polymers are rare, polymers with broad structure and MWD are widely used in medicine and the biomedical sciences. They are integral components in final dosage forms, drug delivery systems (DDS) and in implantable devices. Increasingly uniform polymers are being used to develop more complex medicines (e.g. delivery of biopharmaceuticals, enhanced formulations or DDS's for existing actives). In addition to the function imparted by any new polymer it will be required to meet stringent specifications in terms of cost containment, scalability, biocompatibility and performance. Synthetic polymers with therapeutic activity are also being developed to exploit their polyvalent properties, which is not possible with low molecular weight molecules. There is need to utilise uniform polymers for applications where the polymer may interact with the systemic circulation, tissues or cellular environment. There are also potential applications (e.g. stimuli responsive coatings) where uniform polymers may be used for their more defined property profile. While it is not yet practical to prepare synthetic polymers to the same high degree of uniformity as proteins, nature also effectively utilises many polymers with lower degrees of uniformity (e.g. polysaccharides, poly(amino acids), polyhydroxyalkanoates). In recent years it has become possible to prepare with practical experimental protocols sufficient quantities of polymers that display many aspects of uniformity. This

Novel salicylazo polymers for colon drug delivery: dissolving polymers by means of bacterial degradation.

Science.gov (United States)

Saphier, Sigal; Karton, Yishai

2010-02-01

Novel azo polymers were prepared for colonic drug delivery with a release mechanism based on structural features of azo derivatives designed for rapid bacterial degradation leading to soluble polymers. Two Salicylazo derivatives were prepared and conjugated as side chains at different ratios to methacrylic acid-methyl methacrylate copolymers (Eudragits). The azo compounds were designed to have a hydrophilic and a hydrophobic part on opposite sides of the azo bond. Upon reduction of the azo bonds, the hydrophobic part is released, resulting in a more water soluble polymer. The solubility of the polymeric films was studied relative to Eudragit S known to dissolve toward the end of the small intestine. One of the two azo derivatives prepared gave rise to polymers, which showed reduced solubility relative to Eudragit S. These polymers were subjected to reduction tests in anaerobic rat cecal suspensions by following the release of the hydrophobic product. Reduction rate was found to be rapid, comparable to that of Sulfasalazine. Studies on the azopolymeric films in anaerobic rat cecal suspensions, showed that these polymers dissolve faster than in sterilized suspensions. Solid dosage forms may be coated with these polymers to provide an efficient delivery system to the colon with a rapid release mechanism. (c) 2009 Wiley-Liss, Inc. and the American Pharmacists Association.

Mixed waste solidification testing on polymer and cement-based waste forms in support of Hanford's WRAP 2A facility

International Nuclear Information System (INIS)

Burbank, D.A. Jr.; Weingardt, K.M.

1993-10-01

A testing program has been conducted by the Westinghouse Hanford Company to confirm the baseline waste form selection for use in Waste Receiving and Processing (WRAP) Module 2A. WRAP Module 2A will provide treatment required to properly dispose of containerized contact-handled, mixed low-level waste at the US Department of Energy Hanford Site in south-central Washington State. Solidification/stabilization has been chosen as the appropriate treatment for this waste. This work is intended to test cement-based, thermosetting polymer, and thermoplastic polymer solidification media to substantiate the technology approach for WRAP Module 2A. Screening tests were performed using the major chemical constituent of each waste type to measure the gross compatibility with the immobilization media and to determine formulations for more detailed testing. Surrogate materials representing each of the eight waste types were prepared in the laboratory. These surrogates were then solidified with the selected immobilization media and subjected to a battery of standard performance tests. Detailed discussion of the laboratory work and results are contained in this report

Micro-scale truss structures with three-fold and six-fold symmetry formed from self-propagating polymer waveguides

Energy Technology Data Exchange (ETDEWEB)

Jacobsen, Alan J. [HRL Laboratories LLC, Sensors and Materials Laboratory, 3011 Malibu Canyon Road, Malibu, CA 90265-4797 (United States); Department of Aerospace and Mechanical Engineering, University of Southern California, Los Angeles, CA (United States)], E-mail: ajjacobsen@hrl.com; Barvosa-Carter, William [HRL Laboratories LLC, Sensors and Materials Laboratory, 3011 Malibu Canyon Road, Malibu, CA 90265-4797 (United States); Nutt, Steven [Department of Chemical Engineering and Materials Science, University of Southern California, Los Angeles, CA (United States)

2008-06-15

A process for interconnecting a three-dimensional pattern of self-propagating polymer waveguides was used to form micro-truss structures with two new unit cell architectures. The structures were formed using a two-dimensional mask with a hexagonal pattern of apertures. Distinct unit cell architectures were possible by exposing the mask to a different number of incident UV exposure beams, which are used to form the waveguides. One unit cell design featured three intersecting waveguides per node, resulting in a structure with three-fold symmetry. The second unit cell design had six-fold symmetry and was characterized by primary nodes with six intersecting waveguides and secondary nodes with two intersecting waveguides. Compression loading experiments were conducted on micro-truss samples with comparable relative density values ({rho}/{rho}{sub s} = 6.5%), but different unit cell architectures. The addition of secondary nodes in the structures based on the second design led to an increase in compressive modulus of up to 70% and an average increase in peak strength of 42%. The increase in compressive strength and modulus was attributed to a reduction in the truss-member slenderness ratio achieved through increased waveguide connectivity.

Micro-scale truss structures with three-fold and six-fold symmetry formed from self-propagating polymer waveguides

International Nuclear Information System (INIS)

Jacobsen, Alan J.; Barvosa-Carter, William; Nutt, Steven

2008-01-01

A process for interconnecting a three-dimensional pattern of self-propagating polymer waveguides was used to form micro-truss structures with two new unit cell architectures. The structures were formed using a two-dimensional mask with a hexagonal pattern of apertures. Distinct unit cell architectures were possible by exposing the mask to a different number of incident UV exposure beams, which are used to form the waveguides. One unit cell design featured three intersecting waveguides per node, resulting in a structure with three-fold symmetry. The second unit cell design had six-fold symmetry and was characterized by primary nodes with six intersecting waveguides and secondary nodes with two intersecting waveguides. Compression loading experiments were conducted on micro-truss samples with comparable relative density values (ρ/ρ s = 6.5%), but different unit cell architectures. The addition of secondary nodes in the structures based on the second design led to an increase in compressive modulus of up to 70% and an average increase in peak strength of 42%. The increase in compressive strength and modulus was attributed to a reduction in the truss-member slenderness ratio achieved through increased waveguide connectivity

New hyperthermal thermosetting heterocyclic polymers

Science.gov (United States)

Bilow, N.; Landis, A. L.; Miller, L. J.

1970-01-01

Polyimidazopyrrolone polymers, formed by the condensation of aromatic dianhydrides with aromatic tetraamines in various solvents, form moldings that resist degradation in air and retain great strength at 400 to 700 degrees F. The resins have good insulating properties, are easy to mold, and make good protective coatings.

The free radical process for the polymer surface treated by radio frequency plasma

International Nuclear Information System (INIS)

Ma Yuguang; Yang Meiling; Shen Jiacong; Zheng Yingguang

1992-01-01

The formation and translation of the free radicals on the polymer surface treated by plasmas were studied and observed by ESR measurement. The results show that C-C bond split was main reaction in the process of the polymer irradiated by plasma, by which a stable alkyl free radical was formed. When alkyl free radical contacted with air, they translate into peroxide radical instantaneously. The peroxide radical was not as stable as radical in vacuum, they can react each other to form some polar-groups on polymer surface. The interaction between the peroxide free radical and polymer chain was correlative not only to the structure of polymer but also to the molecular motion of the polymer chain. The nature of plasma treating polymer surface was that the peroxide radicals were led onto polymer surface

Lead selenide quantum dot polymer nanocomposites

Science.gov (United States)

Waldron, Dennis L.; Preske, Amanda; Zawodny, Joseph M.; Krauss, Todd D.; Gupta, Mool C.

2015-02-01

Optical absorption and fluorescence properties of PbSe quantum dots (QDs) in an Angstrom Bond AB9093 epoxy polymer matrix to form a nanocomposite were investigated. To the authors’ knowledge, this is the first reported use of AB9093 as a QD matrix material and it was shown to out-perform the more common poly(methyl methacrylate) matrix in terms of preserving the optical properties of the QD, resulting in the first reported quantum yield (QY) for PbSe QDs in a polymer matrix, 26%. The 1-s first excitonic absorption peak of the QDs in a polymer matrix red shifted 65 nm in wavelength compared to QDs in a hexane solution, while the emission peak in the polymer matrix red shifted by 38 nm. The fluorescence QY dropped from 55% in hexane to 26% in the polymer matrix. A time resolved fluorescence study of the QDs showed single exponential lifetimes of 2.34 and 1.34 μs in toluene solution and the polymer matrix respectively.

The influence of polymer architectures on the dewetting behavior of thin polymer films: from linear chains to ring chains.

Science.gov (United States)

Wang, Lina; Xu, Lin; Liu, Binyuan; Shi, Tongfei; Jiang, Shichun; An, Lijia

2017-05-03

The dewetting behavior of ring polystyrene (RPS) film and linear polystyrene (LPS) film on silanized Si substrates with different grafting densities and PDMS substrate was investigated. Results showed that polymer architectures greatly influenced the dewetting behavior of the thin polymer film. On the silanized Si substrate with 69% grafting density, RPS chains exhibited stronger adsorption compared with LPS chains, and as a result the wetting layer formed more easily. For LPS films, with a decreased annealing temperature, the stability of the polymer film changed from non-slip dewetting via apparent slip dewetting to apparently stable. However, for RPS films, the polymer film stability switched from apparent slip dewetting to apparently stable. On the silanized Si substrate with 94% grafting density, the chain adsorption became weaker and the dewetting processes were faster than that on the substrate with 69% grafting density at the same experimental temperature for both the LPS and RPS films. Moreover, on the PDMS substrate, LPS films always showed non-slip dewetting, while the dewetting kinetics of RPS films switched from non-slip dewetting to slip dewetting behaviour. Forming the wetting layer strongly influenced the stability and dewetting behavior of the thin polymer films.

Simulated glass-forming polymer melts: dynamic scattering functions, chain length effects, and mode-coupling theory analysis.

Science.gov (United States)

Frey, S; Weysser, F; Meyer, H; Farago, J; Fuchs, M; Baschnagel, J

2015-02-01

We present molecular-dynamics simulations for a fully flexible model of polymer melts with different chain length N ranging from short oligomers (N = 4) to values near the entanglement length (N = 64). For these systems we explore the structural relaxation of the supercooled melt near the critical temperature T c of mode-coupling theory (MCT). Coherent and incoherent scattering functions are analyzed in terms of the idealized MCT. For temperatures T > T c we provide evidence for the space-time factorization property of the β relaxation and for the time-temperature superposition principle (TTSP) of the α relaxation, and we also discuss deviations from these predictions for T ≈ T c. For T larger than the smallest temperature where the TTSP holds we perform a quantitative analysis of the dynamics with the asymptotic MCT predictions for the late β regime. Within MCT a key quantity, in addition to T c, is the exponent parameter λ. For the fully flexible polymer models studied we find that λ is independent of N and has a value (λ = 0.735 ) typical of simple glass-forming liquids. On the other hand, the critical temperature increases with chain length toward an asymptotic value T c (∞) . This increase can be described by T c (∞) - T c(N) ∼ 1/N and may be interpreted in terms of the N dependence of the monomer density ρ, if we assume that the MCT glass transition is ruled by a soft-sphere-like constant coupling parameter Γ c = ρ c T c (-1/4), where ρ c is the monomer density at T c. In addition, we also estimate T c from a Hansen-Verlet-like criterion and MCT calculations based on structural input from the simulation. For our polymer model both the Hansen-Verlet criterion and the MCT calculations suggest T c to decrease with increasing chain length, in contrast to the direct analysis of the simulation data.

Di-block co-polymer derived nanoporous polymer liquid core waveguides

DEFF Research Database (Denmark)

Christiansen, Mads Brøkner; Gopalakrishnan, Nimi; Sagar, Kaushal Shashikant

2010-01-01

pores. When the PDMS is etched, the hydrophobic PB is left with a porosity of 44%. The polymer is subsequently UV exposed through a shadow mask. This renders the exposed part hydrophilic, making it possible for water to infiltrate these areas. Water infiltration raises the refractive index, thus forming...

Development of an advanced, continuous mild-gasification process for the production of coproducts. Report for Task 4.8, Decontamination and disassembly of the mild-gasification and char-to-carbon PRUs and disposal of products from testing

Energy Technology Data Exchange (ETDEWEB)

Merriam, N.W. [Western Research Inst., Laramie, WY (United States); Jha, Mahesh C. [AMAX Research and Development Center, Golden, CO (United States)

1991-11-01

This report contains descriptions of mild-gasification and char-to-carbon process research units (PRUS) used by WRI and AMAX R&D Center to conduct tests under contract AC21-87MC24268. Descriptions of materials produced during those tests are also contained herein. Western Research Institute proposes to dispose of remaining fines and dried coal by combustion and remaining coal liquids by incineration during mid-1992. The mild-gasification PRU will be used for additional tests until 1993, at which time WRI proposes to decontaminate and disassemble the PRU. AMAX R&D Center intends to return the spent char, any remaining feed char, and unusable product carbon to the Eagle Butte Mine near Gillette, Wyoming, from where the coal originally came. The solid products will be added to the mine`s coal product stream. Coal liquids collected from condensers will be concentrated and sent to a local oil and solvent recycling company where the liquids will be burned as fuel. The char-to-carbon PRU will be operated periodically until 1993 when the plant will be decontaminated and disassembled.

Effects of Post-Pyrolysis Air Oxidation of Biomass Chars on Adsorption of Neutral and Ionizable Compounds.

Science.gov (United States)

Xiao, Feng; Pignatello, Joseph J

2016-06-21

This study was conducted to understand the effects of thermal air oxidation of biomass chars experienced during formation or production on their adsorptive properties toward various compounds, including five neutral nonpolar and polar compounds and seven weak acids and bases (pKa = 3-5.2) selected from among industrial chemicals and the triazine and phenoxyacetic acid herbicide classes. Post-pyrolysis air oxidation (PPAO) at 400 °C of anoxically prepared wood and pecan shell chars for up to 40 min enhanced the mass-normalized adsorption at pH ∼ 7.4 of all test compounds, especially the weak acids and bases, by up to 100-fold. Both general and specific effects were identified. The general effect results from "reaming" of pores by the oxidative removal of pore wall matter and/or tarry deposits generated during the pyrolysis step. Reaming creates new surface area and enlarges nanopores, which helps relieve steric hindrance to adsorption. The specific effect results from creation of new acidic functionality that provides sites for the formation of very strong, charge-assisted hydrogen bonds (CAHB) with solutes having comparable pKa. The CAHB hypothesis was supported by competition experiments and the finding that weak acid anion adsorption increased with surface carboxyl content, despite electrostatic repulsion from the growing negative charge. The results provide insight into the effects of air oxidation on pollutant retention.

Properties and Developments of Combustion and Gasification of Coal and Char in a CO2-Rich and Recycled Flue Gases Atmosphere by Rapid Heating

Directory of Open Access Journals (Sweden)

Zhigang Li

2012-01-01

Full Text Available Combustion and gasification properties of pulverized coal and char have been investigated experimentally under the conditions of high temperature gradient of order 200°C·s−1 by a CO2 gas laser beam and CO2-rich atmospheres with 5% and 10% O2. The laser heating makes a more ideal experimental condition compared with previous studies with a TG-DTA, because it is able to minimize effects of coal oxidation and combustion by rapid heating process like radiative heat transfer condition. The experimental results indicated that coal weight reduction ratio to gases followed the Arrhenius equation with increasing coal temperature; further which were increased around 5% with adding H2O in CO2-rich atmosphere. In addition, coal-water mixtures with different water/coal mass ratio were used in order to investigate roles of water vapor in the process of coal gasification and combustion. Furthermore, char-water mixtures with different water/char mass ratio were also measured in order to discuss the generation ratio of CO/CO2, and specified that the source of Hydrocarbons is volatile matter from coal. Moreover, it was confirmed that generations of CO and Hydrocarbons gases are mainly dependent on coal temperature and O2 concentration, and they are stimulated at temperature over 1000°C in the CO2-rich atmosphere.

Role of Surface Interactions in the Synergizing Polymer/Clay Flame Retardant Properties

Energy Technology Data Exchange (ETDEWEB)

Pack, S.; Kashiwagi, T; Cao, C; Korach, C; Lewin, M; Rafailovich, M

2010-01-01

The absorption of resorcinol di(phenyl phosphate) (RDP) oligomers on clay surfaces has been studied in detail and is being proposed as an alternative method for producing functionalized clays for nanocomposite polymers. The ability of these clays to be exfoliated or intercalated in different homopolymers was investigated using both transmission electron microscopy and small-angle X-ray scattering results, compared with contact angle measurements on Langmuir-Blodgett clay monolayers, where the interfacial energies were used as predictors of the polymer/clay interactions. We found that the contact angle between PS/RDP clay monolayer substrates was {approx}2.5{sup o}, whereas the angle for polystyrene (PS)/Cloisite 20A clays substrates was {approx}32{sup o}, consistent with the large degree of exfoliation observed in PS for the RDP-coated clays. The interfacial activity of these clays was also measured, and we found that the RDP-coated clays segregated to the interfaces of PC/poly(styrene-co-acrylonitrile) blends, while they segregated into the poly(methyl methacrylate) (PMMA) domain of PS/PMMA blends. This morphology was explained in terms of the relative energy advantage in placing the RDP versus the Cloisite clays at the interfaces. Finally, we demonstrated the effects of the relative surface energies of the clays in segregating to the blend air interface when heated to high temperatures. The segregation was shown to affect the composition and mechanical properties of the resulting chars, which in turn could determine their flame retardant response.

Vacuum ultraviolet photochemistry of polymers

International Nuclear Information System (INIS)

Skurat, Vladimir

2003-01-01

The interaction of vacuum UV radiation (wavelength range from 1 to 200 nm) with polymers is interesting for fundamental and applied sciences. This interest is stimulated by various reasons: - Wide applications of polymeric materials in semiconductor technology, where they are used as photoresist materials in combination with VUV light sources (lasers, excimer lamps, synchrotron radiation and others). - Polymers are widely used as spacecraft materials in the last 20 years. On near-Earth orbits, the polymeric materials of spacecraft surfaces are destroyed by solar radiation. - VUV radiation is one of the components of gas discharge plasmas, which are used for treatment of polymer, with the aim of modifying their surface properties. The main features of interaction of VUV radiation with polymers are discussed. The spectra of intrinsic absorption of saturated polymers (polyethylene, polypropylene, polytetrafluoroethylene and others) are situated mainly in the VUV region. The photochemistry of polymers in the VUV region is very different from their photochemistry at wavelengths longer than 200 nm, where the absorption spectra belong to impurities and polymer defects. The polymer photochemistry in the VUV region is wavelength-dependent. At wavelengths longer than about 140 nm, the main role is played by transformations of primary-formed singlet excited molecules. At shorter wavelengths the role of photoionization increases progressively and the main features of VUV photolysis become similar to the picture of radiolysis, with significant contributions of charge pairs and triplet excited molecules. Very important features of VUV light absorption in polymers are high absorption coefficients. Because of this, the surface layers absorb large doses of energy. This leads to very profound transformation of material on the polymer surface. In particular for polymers which are considered destroyed by radiation (for example, perfluoropolymers), this leads to VUV-induced erosion

Microstructural aspects in steel fiber reinforced acrylic emulsion polymer modified concrete

Directory of Open Access Journals (Sweden)

Hazimmah Dayang

2018-01-01

Full Text Available Scanning electron microscope observations of polymer-free and polymer-modified cements have shown that the polymer particles are partitioned between the inside of hydrates and the surface of anhydrous cement grains. For optimum dosage of acrylic emulsion polymer with 2.5%, the C-S-H gel in this structure is finer and more acicular. Some polymer adheres or deposit on the surface of the C-S-H gel. The presence of acrylic emulsion polymer confines the ionic diffusion so that the Ca(OH2 crystallized locally to form fine crystals. The void in the structures seems to be smaller but no polymer films appears to be bridging the walls of pores although many polymer bonds or C-S-H spread into the pore spaces. In addition to porosity reduction, acrylic emulsion polymer modified the hydration products in the steel fiber –matrix ITZ. The hydration product C-S-H appeared as a needle like shape. The needle-shaped C-S-H increases and gradually formed the gel, with needles growing into the pore space. The phenomenon is more obvious as curing age increased.

Study on dissolution behavior of polymer-bound and polymer-blended photo-acid generator (PAG) resists

Science.gov (United States)

Yamamoto, Hiroki; Kozawa, Takahiro; Tagawa, Seiichi

2013-03-01

The requirements for the next generation resist materials are so challenging that it is indispensable for feasibility of EUV lithography to grasp basic chemistry of resist matrices in all stage of resist processes. Under such circumstances, it is very important to know dissolution characteristics of the resist film into alkaline developer though the dissolution of exposed area of resist films in alkaline developer to form a pattern is a complex reactive process. In this study, the influence of EUV and KrF exposure on the dissolution behavior of polymer bound PAG and polymer blended PAG was studied in detail using quartz crystal microbalance (QCM) methods. The difference in swelling formation between KrF and EUV exposure was observed. It is likely that difference of reaction mechanism induces the difference of these swelling. Also, it is observed that the swelling of polymer-bound PAG is less than that of polymer blended PAG in both KrF and EUV exposure. This result indicates that polymer-bound PAG suppresses swelling very well and showed an excellent performance. Actually, the developed polymer bound-PAG resist showed an excellent performance (half pitch 50 nm line and space pattern). Thus, polymer bound PAG is one of the promising candidate for 16 nm EUV resist.

Lanthanum Containing Polymer's Modification to PP

Institute of Scientific and Technical Information of China (English)

Dai Shaojun; Zhang Ming

2004-01-01

Polypropylene (PP)'s low impact strength limits its usages. Adding some a rare earth polymer can enhance PP's tensile strength and impact strength. Acrylic lanthanum was prepared by the reaction between lanthanum oxide and acrylic acid. The IR spectrum prove that and optimum reacting conditions are that the bulk ratio of La(AA) 3 and MMA is not less than one and temperature is about 80 ℃. Lanthanum containing Polymer were added into PP. When percent of addition only was 3%, strength were enhanced 10% , and impact strength 40%. SEM shows the compatibility of rare earth polymer and PP; lanthanum containing polymer can form physical crosslinking between PP's molecules, then every particle's surface connect with several PP molecules and the PP mechanical property were enhanced.