WorldWideScience

Sample records for cesium 131

  1. Assessment of food calcium radioprotection effectiveness against cesium-137, added alone and with iodine-131

    International Nuclear Information System (INIS)

    New fish product with addition of food calcium had radioprotective properties, resulted in decreased cesium-137 content in organs and tissues of animals by 40-60% and lesser changes in differential blood count and biochemical indexes of blood serum

  2. Oak Ridge Reservation Volume 3. Records relating to RaLa, iodine-131, and cesium-137 at the Oak Ridge National Laboratory and the Oak Ridge Operations Office: A guide to record series of the Department of Energy and its contractors

    International Nuclear Information System (INIS)

    The purpose of this guide is to describe each of the documents and record series pertaining to the production, release, and disposal of radioactive barium-lanthanum (RaLa), iodine-131, and cesium-137 at the Department of Energy's (DOE) Oak Ridge National Laboratory (ORNL) in Oak Ridge, Tennessee. History Associates Incorporated (HAI) prepared this guide as part of DOE's Epidemiologic Records Inventory Project, which seeks to verify and conduct inventories of epidemiologic and health-related records at various DOE and DOE contractor sites. This introduction briefly describes the Epidemiologic Records Inventory Project and HAI's role. It provides information on the history of the DOE-Oak Ridge Reservation (ORR), particularly ORNL. Specific attention is given to the production of RaLa and the fission products iodine-131 and cesium-137. This introduction also describes the methodologies HAI used in the selection and inventorying of documents and record series pertaining to RaLa, iodine-131, and cesium-137, and in the production of this guide. Concluding paragraphs describe the arrangement of the record series, explain the information contained in the record series descriptions, and indicate restrictions on access to the records

  3. Representation of a model of radionuclide transfer in food chains following deposition of strontium-90, cesium-137 and iodine-131 on areas for agricultural use

    International Nuclear Information System (INIS)

    The 'SINK' model (contaminants in food chains - FORTRAN 77) was used in an attempt to predict the amounts of radioactivity building up in animal and vegetable foods after one single deposition of Sr-90, Cs-137 and I-131. The model is described in detail. The input quantities include such factors as time-integrated concentration of activity in the air just above the ground, physicochemical form of the radionuclides, activity deposited with precipitation and amount of rain to fall in any particular case. The model was so designed as to take account of 18 different plants, 11 animal products and 14 kinds of processed nutrients. The radionuclide contents of vegetable foods were calculated with reference to the season of the year, at which deposition took place. The estimations of the activity concentrations in animal foods were in each case based on different fudder rations. (orig./HP)

  4. Cesium-137

    International Nuclear Information System (INIS)

    This sheet belongs to a collection which relates to the use of radionuclides essentially in unsealed sources. Its goal is to gather on a single document the most relevant information as well as the best prevention practices to be implemented. These sheets are made for the persons in charge of radiation protection: users, radioprotection-skill persons, labor physicians. Each sheet treats of: 1 - the radio-physical and biological properties; 2 - the main uses; 3 - the dosimetric parameters; 4 - the measurement; 5 - the protection means; 6 - the areas delimitation and monitoring; 7 - the personnel classification, training and monitoring; 8 - the effluents and wastes; 9 - the authorization and declaration administrative procedures; 10 - the transport; and 11 - the right conduct to adopt in case of incident or accident. This sheet deals specifically with Cesium-137

  5. Decorporation of cesium-137

    International Nuclear Information System (INIS)

    Cesium radio-isotopes, especially cesium-137 (137Cs) are among the radionuclides of main importance produced by a fission reaction in reactor or a nuclear weapon explosion. In the environment, 137Cs is a major contaminant which can cause severe β, γirradiations and contaminations. 137Cs is distributed widely and relatively uniformly throughout the body with the highest concentration in skeletal muscles. A treatment becomes difficult afterwards. The purposes of this report are Firstly to compare the Prussian blue verses cobalt and potassium ferrocyanide (D.I. blue) efficiency for the 137Cs decorporation and secondly to assess a chronological treatment with D.I. blue. (author)

  6. Cesium reservoir and interconnective components

    International Nuclear Information System (INIS)

    The program objective is to demonstrate the technology readiness of a TFE (thermionic fuel element) suitable for use as the basic element in a thermionic reactor with electric power output in the 0.5 to 5.0 MW range. A thermionic converter must be supplied with cesium vapor for two reasons. Cesium atoms adsorbed on the surface of the emitter cause a reduction of the emitter work function to permit high current densities without excessive heating of the emitter. The second purpose of the cesium vapor is to provide space-charge neutralization in the emitter-collector gap so that the high current densities may flow across the gap unattenuated. The function of the cesium reservoir is to provide a source of cesium atoms, and to provide a reserve in the event that cesium is lost from the plasma by any mechanism. This can be done with a liquid cesium metal reservoir in which case it is heated to the desired temperature with auxiliary heaters. In a TFE, however, it is desirable to have the reservoir passively heated by the nuclear fuel. In this case, the reservoir must operate at a temperature intermediate between the emitter and the collector, ruling out the use of liquid reservoirs. Integral reservoirs contained within the TFE will produce cesium vapor pressures in the desired range at typical electrode temperatures. The reservoir material that appears to be the best able to meet requirements is graphite. Cesium intercalates easily into graphite, and the cesium pressure is insensitive to loading for a given intercalation stage. The goals of the cesium reservoir test program were to verify the performance of Cs-graphite reservoirs in the temperature-pressure range of interest to TFE operation, and to test the operation of these reservoirs after exposure to a fast neutron fluence corresponding to seven year mission lifetime. In addition, other materials were evaluated for possible use in the integral reservoir

  7. Cesium-137 in biosphere

    International Nuclear Information System (INIS)

    The behaviour of cesium-137 in environment is reviewed. Problems on 137Cs migration in environment, on metabolism andbiological effects are considered. Data on nuclide accumulation in various plants, ways of their entering the man's organism are presented. It is marked that the rate of 137Cs metabolism in the man's organism depends considerably on age, sex, temperature of environment, conditions for activity, water and mineral metabolism and some other factors. It is shown that the annual effective equivalent dose per capita will increase to 2000 yr. up to 1 μSv, that constitutes 0.05% of the average value of irradiation by a natural source

  8. Cesium diffusion in graphite

    Energy Technology Data Exchange (ETDEWEB)

    Evans, R.B. III; Davis, W. Jr.; Sutton, A.L. Jr.

    1980-05-01

    Experiments on diffusion of /sup 137/Cs in five types of graphite were performed. The document provides a completion of the report that was started and includes a presentation of all of the diffusion data, previously unpublished. Except for data on mass transfer of /sup 137/Cs in the Hawker-Siddeley graphite, analyses of experimental results were initiated but not completed. The mass transfer process of cesium in HS-1-1 graphite at 600 to 1000/sup 0/C in a helium atmosphere is essentially pure diffusion wherein values of (E/epsilon) and ..delta..E of the equation D/epsilon = (D/epsilon)/sub 0/ exp (-..delta..E/RT) are about 4 x 10/sup -2/ cm/sup 2//s and 30 kcal/mole, respectively.

  9. Cesium transport data for HTGR systems

    International Nuclear Information System (INIS)

    Cesium transport data on the release of cesium from HTGR fuel elements are reviewed and discussed. The data available through 1976 are treated. Equations, parameters, and associated variances describing the data are presented. The equations and parameters are in forms suitable for use in computer codes used to calculate the release of metallic fission products from HTGR fuel elements into the primary circuit. The data cover the following processes: (1) diffusion of cesium in fuel kernels and pyrocarbon, (2) sorption of cesium on fuel rod matrix material and on graphite, and (3) migration of cesium in graphite. The data are being confirmed and extended through work in progress

  10. Decorporation of cesium-137; Decorporation du cesium-137

    Energy Technology Data Exchange (ETDEWEB)

    Le Fleche, Ph.; Destombe, C.; Grasseau, A.; Mathieu, J.; Chancerelle, Y.; Mestries, J.C. [GMR, Direction des Recherches, Etudes et Techniques, 94 - Arcueil (France)

    1997-12-31

    Cesium radio-isotopes, especially cesium-137 ({sup 137}Cs) are among the radionuclides of main importance produced by a fission reaction in reactor or a nuclear weapon explosion. In the environment, {sup 137}Cs is a major contaminant which can cause severe {beta}, {gamma}irradiations and contaminations. {sup 137}Cs is distributed widely and relatively uniformly throughout the body with the highest concentration in skeletal muscles. A treatment becomes difficult afterwards. The purposes of this report are Firstly to compare the Prussian blue verses cobalt and potassium ferrocyanide (D.I. blue) efficiency for the {sup 137}Cs decorporation and secondly to assess a chronological treatment with D.I. blue. (author)

  11. Extraction of radioactive cesium from tea leaves

    International Nuclear Information System (INIS)

    Radioactive contamination of foodstuffs attributed to the Fukushima Daiichi nuclear disaster has become a social problem. This study investigated the extraction of radioactive cesium from the contaminated leaves to the tea. The green tea was brewed twice reusing the same leaves to study the difference in extraction of cesium between the first and second brew. Moreover, the extraction of cesium was studied in correlation to brewing time. The concentration of radioactive cesium was determined with gamma spectrometry, and the concentration of caffeine was determined with absorption spectrometry. About 40% of cesium was extracted from leaves in the first brew, and about 80% was extracted in the second brew. The extraction of cesium increased over time, and it reached about 80% after 10 minutes brew. The ratio of radioactive cesium to caffeine decreased linearly over time. This study revealed that the extraction of cesium was higher for the second brew, and a rapid increase in extraction was seen as the tea was brewed for 6 minutes and more. Therefore, the first brew of green tea, which was brewed within 5 minutes, contained the least extraction of radioactive cesium from the contaminated leaves. (author)

  12. Activity of cesium-134 and cesium-137 in game and mushrooms in Poland

    International Nuclear Information System (INIS)

    The activity of cesium-134 and cesium-137 was measured in mushrooms and game in 1986-1991. The samples were collected all over Poland and most of the measurements were carried out for export purposes. The results indicate that the activity ratio of cesium-137 to cesium-134 in some samples is not comparable to that with fallout after the Chernobyl accident. The analysis of some samples of mushrooms from 1985 showed that the activity of cesium-137 was higher compared to any other foodstuff. The level of contamination varied greatly throughout Poland

  13. Surface tension of liquid dilute solutions of lead-cesium and bismuth-cesium systems

    International Nuclear Information System (INIS)

    Method of the maximal pressure in a drop was used to measure the surface tension of 15 liquid dilute solutions of lead-cesium system in 0-0.214 at% concentration range and of 12 diluted solutions of bismuth-cesium system in 0-0.160 at.% cesium range from solidification temperature up to 500 dec C. It was found that cesium was characterized as surfactant in lead and bismuth melts. It was established that the temperature coefficient of surface tension changes sufficiently in maximally diluted solutions of alkali metals in bismuth and lead melts. Effect of sodium, potassium, rubidum and cesium on the value of surface tension of lead and bismuth was systematized. Growth of activity in sodium, potassium, rubidium and cesium series was noted

  14. Sorption of cesium on Latvian clays

    International Nuclear Information System (INIS)

    Cesium is like potassium - good solubility and mobile in a ground, easily assimilate in organism expressly brawn woof. It is a problem if pollutant is a radioactive 137Cs. We made experiments to sorption a 2M CsF solution on some Latvian clays which mainly contain hydro micas (cesium content after good elute of clays are in table). We establish, that clay treated with 25 % sulfuric acid adsorb cesium two times more that waste clay. Hereto unstuck elute Cs from clays. (author)

  15. Cesium and strontium ion specific exchangers

    Energy Technology Data Exchange (ETDEWEB)

    Yates, S.

    1996-10-01

    This work is one of two parallel projects that are part of an ESP task to develop high-capacity, selective, solid extractants for cesium, strontium, and technetium from nuclear wastes. In this subtask, Pacific Northwest National Laboratory (PNNL) is collaborating with AlliedSignal, Inc. (Des Plaines, Illinois) to develop inorganic ion exchangers that are selective for strontium and cesium from alkaline high-level waste and groundwater streams.

  16. Sorption of Cesium on Latvia clays

    International Nuclear Information System (INIS)

    Cesium is like potassium - good solubility and mobile in a ground, easy assimilates in organism expressly brawn woof. It is a problem if pollutant is radioactive 137Cs. We made experiments to sorption a 2M CsF solution on some Latvian clays which mainly contain hydro micas. We establish that clay treated with 25% sulfuric acid absorb cesium two times more that waste clay. Hereto unstuck elute Cs from clays

  17. Removal of cesium from wastewater: A cesium-specific ion exchange resin

    International Nuclear Information System (INIS)

    Researchers at the Savannah River Laboratory (SRL) have applied for a patent for an ion exchange resin that will remove cesium from water. Radioactive cesium-137 is a fission product of nuclear reactor operations. Cesium may enter the water of spent fuel holding basins through defects in fuel cladding. Control of cesium in these basins is desirable to keep personnel exposure to a minimum. Cesium is also present in the waste from reprocessing of defense nuclear reactor fuel. Research has been underway at SRL for over a decade to improve management of high-level reprocessing waste. The current technology separates the waste into soluble and insoluble components. Radioactive constituents are removed from the soluble component stream and combined with the insoluble components, which are then converted to a glass for long-term storage. Cesium is the most radioactive constituent of the soluble components stream. The SRL resin is a resorcinol-formaldehyde condensation polymer highly specific for cesium and is about 10 times more effective in removal of cesium than other ion exchange resins evaluated for use in processing defense nuclear waste. Tests have been run at SRL using both simulated and actual waste streams

  18. Radioactive cesium in Finnish mushrooms

    International Nuclear Information System (INIS)

    Surveillance of radioactive cesium in Finnish mushrooms was started in 1986 at STUK. Results of the surveillance programs carried out in Lapland and other parts of Finland are given in this report. More than 2000 samples of edible mushrooms have been analysed during 1986-2008. The 137Cs detected in the mushrooms mainly originates from the 137Cs deposition due to the accident at the Chernobyl nuclear power plant in 1986. The 137Cs concentrations of mushrooms in the end of 1970s and in the beginning of 1980s varied from some ten to two hundred becquerels per kilogram originating from the nuclear weapon test period. The uneven division of the Chernobyl fallout is seen in the areal variation of 137Cs concentrations of mushrooms, the 137Cs concentrations being about tenfold in the areas with the highest deposition compared to those where the deposition was lowest. After the Chernobyl accident the maximum values in the 137Cs concentrations were reached during 1987-88 among most species of mushrooms. The 137Cs concentrations have decreased slowly, being in 2008 about 40 per cent of the maximum values. The 137Cs concentrations may be tenfold in the mushroom species with high uptake of cesium (Rozites caperatus, Hygrophorus camarophyllus, Lactarius trivialis) compared to the species with low uptake (Albatrellus ovinus, Leccinum sp.) picked in the same area. The 137Cs contents in certain species of commercial mushrooms in Finland still exceed the maximum permitted level, 600 Bq/kg, recommended to be respected when placing wild game, wild berries, wild mushrooms and lake fish on the market (Commission recommendation 2003/274/Euratom). Therefore, the 137Cs concentrations of mushrooms should be measured before placing them on the market in the areas of the highest 137Cs deposition, except for Albatrellus ovinus, Boletus sp. and Cantharellus cibarius. The 137Cs concentrations of common commercial mushroom species, Cantharellus tubaeformis and Craterellus cornucopioides often

  19. Plasma etching of cesium iodide

    International Nuclear Information System (INIS)

    Thick films of cesium iodide (CsI) are often used to convert x-ray images into visible light. Spreading of the visible light within CsI, however, reduces the resolution of the resulting image. Anisotropic etching of the CsI film into an array of micropixels can improve the image resolution by confining light within each pixel. The etching process uses a high-density inductively coupled plasma to pattern CsI samples held by a heated, rf-biased chuck. Fluorine-containing gases such as CF4 are found to enhance the etch rate by an order of magnitude compared to Ar+ sputtering alone. Without inert-gas ion bombardment, however, the CF4 etch becomes self-limited within a few microns of depth due to the blanket deposition of a passivation layer. Using CF4+Ar continuously removes this layer from the lateral surfaces, but the formation of a thick passivation layer on the unbombarded sidewalls of etched features is observed by scanning electron microscopy. At a substrate temperature of 220 deg. C, the minimum ion-bombardment energy for etching is Ei∼50 eV, and the rate depends on Ei1/2 above 65 eV. In dilute mixtures of CF4 and Ar, the etch rate is proportional to the gas-phase density of atomic fluorine. Above 50% CF4, however, the rate decreases, indicating the onset of net surface polymer deposition. These observations suggest that anisotropy is obtained through the ion-enhanced inhibitor etching mechanism. Etching exhibits an Arrhenius-type behavior in which the etch rate increases from ∼40 nm/min at 40 deg. C to 380 nm/min at 330 deg. C. The temperature dependence corresponds to an activation energy of 0.13±0.01 eV. This activation energy is consistent with the electronic sputtering mechanism for alkali halides

  20. Perlite for permanent confinement of cesium

    Science.gov (United States)

    Balencie, J.; Burger, D.; Rehspringer, J.-L.; Estournès, C.; Vilminot, S.; Richard-Plouet, M.; Boos, A.

    2006-06-01

    We present the potential use of expanded perlite, a metastable amorphous hydrated aluminium silicate, as a permanent medium for the long-term confinement of cesium. The method requires simply a loading by mixing an aqueous cesium nitrate solution and expanded perlite at 300 K followed by densification by sintering. The formation of pollucite, CsAlSi2O6, a naturally occurring mineral phase, upon careful heat treatment is demonstrated by X-ray diffraction. Leaching tests on the resulting glass-ceramics reveal a very low Cs departure of 0.5 mg m-2 d-1.

  1. Crystalline silicotitanates for cesium/strontium removal

    Energy Technology Data Exchange (ETDEWEB)

    Brown, N.; Miller, J.; Sherman, J.

    1996-10-01

    A new class of inorganic ion exchangers called crystalline silicotitanates (CST) has been developed that exhibits very high selectivity for cesium and strontium in the highly alkaline radioactive wastes at the Hanford Site and other DOE sites. Tests have also shown that CSTs have high selectivity for cesium in acidic and neutral solutions. The ESP is supporting an effort at Sandia National Laboratories and Texas A & M University to further develop and characterize the important chemical and physical properties that will determine the applicability of CST to radioactive waste treatment at Hanford and other DOE facilities.

  2. Microbial accumulation of uranium, radium, and cesium

    International Nuclear Information System (INIS)

    Diverse microbial species varied considerably in their ability to accumulate uranium, cesium, and radium. Mechanistic differences in uranium uptake by Saccharomyces cerevisiae and Pseudomonas aeruginosa were indicated. S. serevisiae exhibited a slow (hours) surface accumulation of uranium which was subject to environmental factors, while P. aeruginosa accumulated uranium rapidly (minutes) as dense intracellular deposits and did not appear to be affected by environmental parameters. Metabolism was not required for uranium uptake by either organism. Cesium and radium were concentrated to a considerably lesser extent than uranium by the several species tested

  3. Removal of Radioactive Cesium Using Prussian Blue Magnetic Nanoparticles

    Directory of Open Access Journals (Sweden)

    Sung-Chan Jang

    2014-11-01

    Full Text Available Radioactive cesium (137Cs has inevitably become a human concern due to exposure from nuclear power plants and nuclear accident releases. Many efforts have been focused on removing cesium and the remediation of the contaminated environment. In this study, we elucidated the ability of Prussian blue-coated magnetic nanoparticles to eliminate cesium from radioactive contaminated waste. Thus, the obtained Prussian blue-coated magnetic nanoparticles were then characterized and examined for their physical and radioactive cesium adsorption properties. This Prussian blue-coated magnetic nanoparticle-based cesium magnetic sorbent can offer great potential for use in in situ remediation.

  4. Cesium vapor thermionic converter anomalies arising from negative ion emission

    Science.gov (United States)

    Rasor, Ned S.

    2016-08-01

    Compelling experimental evidence is given that a longstanding limit encountered on cesium vapor thermionic energy converter performance improvement and other anomalies arise from thermionic emission of cesium negative ions. It is shown that the energy that characterizes thermionic emission of cesium negative ions is 1.38 eV and, understandably, is not the electron affinity 0.47 eV determined for the photodetachment threshold of the cesium negative ion. The experimental evidence includes measurements of collector work functions and volt-ampere characteristics in quasi-vacuum cesium vapor thermionic diodes, along with reinterpretation of the classic Taylor-Langmuir S-curve data on electron emission in cesium vapor. The quantitative effects of negative ion emission on performance in the ignited, unignited, and quasi-vacuum modes of cesium vapor thermionic converter operation are estimated.

  5. Anomalous wetting of helium on cesium

    International Nuclear Information System (INIS)

    The authors report studies of the anomalous wetting of a cesium substrate by a liquid helium film by means of the technique of third sound. A hysteretic pre-wetting transition is observed as a function of the amount of helium in the experimental cell. 10 refs., 2 figs

  6. Cesium and Strontium Separation Technologies Literature Review

    Energy Technology Data Exchange (ETDEWEB)

    T. A. Todd; T. A. Todd; J. D. Law; R. S. Herbst

    2004-03-01

    Integral to the Advanced Fuel Cycle Initiative (AFCI) Program’s proposed closed nuclear fuel cycle, the fission products cesium and strontium in the dissolved spent nuclear fuel stream are to be separated and managed separately. A comprehensive literature survey is presented to identify cesium and strontium separation technologies that have the highest potential and to focus research and development efforts on these technologies. Removal of these high-heat-emitting fission products reduces the radiation fields in subsequent fuel cycle reprocessing streams and provides a significant short-term (100 yr) heat source reduction in the repository. This, along with separation of actinides, may provide a substantial future improvement in the amount of fuel that could be stored in a geologic repository. The survey and review of the candidate cesium and strontium separation technologies are presented herein. Because the AFCI program intends to manage cesium and strontium together, technologies that simultaneously separate both elements are of the greatest interest, relative to technologies that separate only one of the two elements.

  7. Lanthanide doped strontium-barium cesium halide scintillators

    Energy Technology Data Exchange (ETDEWEB)

    Bizarri, Gregory; Bourret-Courchesne, Edith; Derenzo, Stephen E.; Borade, Ramesh B.; Gundiah, Gautam; Yan, Zewu; Hanrahan, Stephen M.; Chaudhry, Anurag; Canning, Andrew

    2015-06-09

    The present invention provides for a composition comprising an inorganic scintillator comprising an optionally lanthanide-doped strontium-barium, optionally cesium, halide, useful for detecting nuclear material.

  8. Surface interactions of cesium and boric acid with stainless steel

    International Nuclear Information System (INIS)

    In this report, the effects of cesium hydroxide and boric acid on oxidized stainless steel surfaces at high temperatures and near one atmosphere of pressure are investigated. This is the first experimental investigation of this chemical system. The experimental investigations were performed using a mass spectrometer and a mass electrobalance. Surfaces from the different experiments were examined using a scanning electron microscope to identify the presence of deposited species, and electron spectroscopy for chemical analysis to identify the species deposited on the surface. A better understanding of the equilibrium thermodynamics, the kinetics of the steam-accelerated volatilizations, and the release kinetics are gained by these experiments. The release rate is characterized by bulk vaporization/gas-phase mass transfer data. The analysis couples vaporization, deposition, and desorption of the compounds formed by cesium hydroxide and boric acid under conditions similar to what is expected during certain nuclear reactor accidents. This study shows that cesium deposits on an oxidized stainless steel surface at temperatures between 1000 and 1200 Kelvin. Cesium also deposits on stainless steel surfaces coated with boric oxide in the same temperature ranges. The mechanism for cesium deposition onto the oxide layer was found to involve the chemical reaction between cesium and chromate. Some revaporization in the cesium hydroxide-boric acid system was observed. It has been found that under the conditions given, boric acid will react with cesium hydroxide to form cesium metaborate. A model is proposed for this chemical reaction

  9. Distribution and retention of cesium in Swedish boreal forest ecosystems

    International Nuclear Information System (INIS)

    The retention and distribution of cesium in forest environments are being studied at three locations in Sweden. The main part of the cesium found in the soil was recovered in horizons rich in organic matter. The cesium was retained in the soil organic matter in a more or less extractable form. As different soil types have a different distribution pattern of organic matter the distribution of cesium will depend on the forest soil type. The clay content in Swedish forest soils is in general low which will mitigate the retention of cesium in the soil mineral horizons. The cesium present in the tree was considered to be an effect of assimilation by the tissues in the canopy as well as by the roots. The redistribution of cesium within the trees was extensive which was considered to be an effect of a high mobility of cesium in the close system of a forest environment. The cesium will remain in the forest environment for a considerable time but can be removed by forest practice, by leaching out of the soil profile or by the radioactive decay. (au)

  10. Sorption of cesium in intact rock

    Energy Technology Data Exchange (ETDEWEB)

    Puukko, E. [Univ. of Helsinki, Dept. of Chemistry (Finland)

    2014-04-15

    The mass distribution coefficient K{sub d} is used in performance assessment (PA) to describe sorption of a radionuclide on rock. The R{sub d} is determined using crushed rock which causes uncertainty in converting the R{sub d} values to K{sub d} values for intact rock. This work describes a method to determine the equilibrium of sorption on intact rock. The rock types of the planned Olkiluoto waste disposal site were T-series mica gneiss (T-MGN), T-series tonalite granodiorite granite gneiss (T-TGG), P-series tonalite granodiorite granite gneiss (P-TGG) and pegmatitic granite (PGR). These rocks contain different amount of biotite which is the main sorbing mineral. The sorption of cesium on intact rock slices was studied by applying an electrical field to speed up migration of cesium into the rock. Cesium is in the solution as a noncomplex cation Cs{sup +} and it is sorbed by ion exchange. The tracer used in the experiments was {sup 134}Cs. The experimental sorption on the intact rock is compared with values calculated using the in house cation exchange sorption model (HYRL model) in PHREEQC program. The observed sorption on T-MGN and T-TGG rocks was close to the calculated values. Two PGR samples were from a depth of 70 m and three samples were from a depth of 150 m. Cesium sorbed more than predicted on the two 70 m PGR samples. The sorption of Cs on the three 150 m PGR samples was small which was consistent with the calculations. The pegmatitic granite PGR has the smallest content of biotite of the four rock types. In the case of P-TGG rock the observed values of sorption were only half of the calculated values. Two kind of slices were cut from P-TGG drill core. The slices were against and to the direction of the foliation of the biotite rims. The sorption of cesium on P-TGG rock was same in both cases. The results indicated that there was no effect of the directions of the electric field and the foliation of biotite in the P-TGG rock. (orig.)

  11. 9 CFR 3.131 - Sanitation.

    Science.gov (United States)

    2010-01-01

    ... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Sanitation. 3.131 Section 3.131... Mammals Animal Health and Husbandry Standards § 3.131 Sanitation. (a) Cleaning of enclosures. Excreta... being directly sprayed with the stream of water or wetted involuntarily. (b) Sanitation of...

  12. 33 CFR 117.131 - Little River.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Little River. 117.131 Section 117.131 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES DRAWBRIDGE OPERATION REGULATIONS Specific Requirements Arkansas § 117.131 Little River. The draws of the...

  13. 24 CFR 9.131 - Direct threat.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Direct threat. 9.131 Section 9.131... DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT § 9.131 Direct threat. (a) This part does not require the agency..., privileges, advantages and accommodations of that agency when that individual poses a direct threat to...

  14. 40 CFR 131.40 - Puerto Rico

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 21 2010-07-01 2010-07-01 false Puerto Rico 131.40 Section 131.40... Federally Promulgated Water Quality Standards § 131.40 Puerto Rico (a) Use designations for marine waters. In addition to the Commonwealth's adopted use designations, the following waterbodies in Puerto...

  15. 49 CFR 237.131 - Design.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Design. 237.131 Section 237.131 Transportation... TRANSPORTATION BRIDGE SAFETY STANDARDS Repair and Modification of Bridges § 237.131 Design. Each repair or... component of a bridge shall be designed by a railroad bridge engineer. The design shall specify the...

  16. 5 CFR 185.131 - Sanctions.

    Science.gov (United States)

    2010-01-01

    ... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Sanctions. 185.131 Section 185.131 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS PROGRAM FRAUD CIVIL REMEDIES § 185.131 Sanctions. (a) The ALJ may sanction a person including any party or representative for...

  17. 10 CFR 600.131 - Insurance coverage.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Insurance coverage. 600.131 Section 600.131 Energy... Nonprofit Organizations Post-Award Requirements § 600.131 Insurance coverage. Recipients shall, at a minimum, provide the equivalent insurance coverage for real property and equipment acquired with DOE funds...

  18. 19 CFR 122.131 - Application.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Application. 122.131 Section 122.131 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY AIR COMMERCE REGULATIONS Aircraft Liquor Kits § 122.131 Application. (a) Liquor and tobacco. Subpart...

  19. 28 CFR 13.1 - Purpose.

    Science.gov (United States)

    2010-07-01

    ... 28 Judicial Administration 1 2010-07-01 2010-07-01 false Purpose. 13.1 Section 13.1 Judicial Administration DEPARTMENT OF JUSTICE ATOMIC WEAPONS AND SPECIAL NUCLEAR MATERIALS REWARDS REGULATIONS § 13.1 Purpose. This part implements the responsibility given to the Attorney General under the Atomic...

  20. Therapeutical uses of 131I

    International Nuclear Information System (INIS)

    Physiology of thyroid gland, pathology of thyroid , papillary, follicular cancer is considered together as differentiated thyroid cancer with very good results under therapy with iodine, invitro determination of calcitonin, search of metastasis, anaplastic carcinoma, as indifferentiated carcinoma with similar results as medullary carcinoma. This work gives a protocol for therapeutical use of 131I , in hyperthyroidism due to Graves-Basedow disease, thyrotoxic adenoma or Plummer disease, toxic multi nodular goiter, subacute thyroiditis. Is studied too the treatment with pharmaceuticals, surgery and radioactive iodine. A recommended use of each and protocol for iodine administration, fixed dose technique, dose estimation,absorbed dose, recommendations about when to use and not use 131I are included in this work

  1. Production of fission 131I

    International Nuclear Information System (INIS)

    A method of iodine separation from other radionuclides generated by 235U fission has been developed in order to explore the possibilities to obtain 131I as by-product of the 99Mo routine production in the Ezeiza Atomic Centre. The experiments were designed to remove this element to gas phase, and the recoveries were investigated both with and without carrier addition. High volatilization percentages were achieved in the presence of iodine carrier. Some other alternatives to increase the iodine displacement to the gaseous phase, namely vacuum distillation, addition of hydrogen peroxide and use of a carrier gas, were also studied. The method developed, which employs a carrier gas stream, without carrier addition, allows the recovery of about 97% of the 131I, with high specific activity, in a simple and clean way. (author)

  2. Distillation device supplies cesium vapor at constant pressure

    Science.gov (United States)

    Basiulis, A.; Shefsiek, P. K.

    1968-01-01

    Distillation apparatus in the form of a U tube supplies small amounts of pure cesium vapor at constant pressure to a thermionic converter. The upstream leg of the U tube is connected to a vacuum pump to withdraw noncondensable impurities, the bottom portion serves as a reservoir for the liquid cesium.

  3. Extraction of radioactive cesium from ash of flammable radioactive material

    International Nuclear Information System (INIS)

    Huge amount of radioactive materials was released by the hydrogen explosion at Fukushima Daiichi Nuclear Power Plant due to the Great East Japan Earthquake on March 11, 2011. Suppression of the volume of radioactive materials stored by decontamination works is strongly required since the preparation of storage places is not easy. We are developing the technology for separation and concentration of radioactive cesium using nano-particle, Prussian blue, as a cesium adsorption material which has a high efficiency and good selectivity. We propose a method in which radioactive cesium is extracted from the ash of flammable materials into the water and the Prussian blue nano-particles are added to the water to collect cesium. The volume of radioactive wastes contaminated by cesium is expected to be cut down with these processes. (J.P.N.)

  4. A combined cesium-strontium extraction/recovery process

    International Nuclear Information System (INIS)

    A new solvent extraction process for the simultaneous extraction of cesium and strontium from acidic nitrate media is described. This process uses a solvent formulation comprised of 0.05 M di-t-butylcyclohexano-18-crown-6 (DtBuCH18C6), 0.1 M Crown 100' (a proprietary, cesium-selective derivative of dibenzo-18-crown-6), 1.2 M tributyl phosphate (TBP), and 5% (v/v) lauryl nitrile in an isoparaffinic hydrocarbon diluent. Distribution ratios for cesium and strontium from 4 M nitric acid are 4.13 and 3.46, respectively. A benchtop batch countercurrent extraction experiment indicates that >98% of the cesium and strontium initially present in the feed solution can be removed in only four extraction stages. Through proper choice of extraction and strip conditions, extracted cesium and strontium can be recovered either together or individually

  5. Plutonium and Cesium Colloid Mediated Transport

    Science.gov (United States)

    Boukhalfa, H.; Dittrich, T.; Reimus, P. W.; Ware, D.; Erdmann, B.; Wasserman, N. L.; Abdel-Fattah, A. I.

    2013-12-01

    Plutonium and cesium have been released to the environment at many different locations worldwide and are present in spent fuel at significant levels. Accurate understanding of the mechanisms that control their fate and transport in the environment is important for the management of contaminated sites, for forensic applications, and for the development of robust repositories for the disposal of spent nuclear fuel and nuclear waste. Plutonium, which can be present in the environment in multiple oxidations states and various chemical forms including amorphous oxy(hydr)oxide phases, adsorbs/adheres very strongly to geological materials and is usually immobile in all its chemical forms. However, when associated with natural colloids, it has the potential to migrate significant distances from its point of release. Like plutonium, cesium is not very mobile and tends to remain adhered to geological materials near its release point, although its transport can be enhanced by natural colloids. However, the reactivity of plutonium and cesium are very different, so their colloid-mediated transport might be significantly different in subsurface environments. In this study, we performed controlled experiments in two identically-prepared columns; one dedicated to Pu and natural colloid transport experiments, and the other to Cs and colloid experiments. Multiple flow-through experiments were conducted in each column, with the effluent solutions being collected and re-injected into the same column two times to examine the persistence and scaling behavior of the natural colloids, Pu and Cs. The data show that that a significant fraction of colloids were retained in the first elution through each column, but the eluted colloids collected from the first run transported almost conservatively in subsequent runs. Plutonium transport tracked natural colloids in the first run but deviated from the transport of natural colloids in the second and third runs. Cesium transport tracked natural

  6. Adsorption of cesium on cement mortar from aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Volchek, Konstantin, E-mail: konstantin.volchek@ec.gc.ca [Emergencies Science and Technology Section, Environment Canada, 335 River Road, Ottawa, Ontario, Canada K1A 0H3 (Canada); Miah, Muhammed Yusuf [Emergencies Science and Technology Section, Environment Canada, 335 River Road, Ottawa, Ontario, Canada K1A 0H3 (Canada); Department of Applied Chemistry and Chemical Technology, Noakhali Science and Technology University (Bangladesh); Kuang, Wenxing; DeMaleki, Zack [Emergencies Science and Technology Section, Environment Canada, 335 River Road, Ottawa, Ontario, Canada K1A 0H3 (Canada); Tezel, F. Handan [Department of Chemical and Biological Engineering, University of Ottawa, 161 Louis-Pasteur, Ottawa, Ontario, Canada K1N 6N5 (Canada)

    2011-10-30

    Highlights: {yields} The adsorption of cesium on cement mortar was investigated in a range of temperatures and cesium concentrations. {yields} The pseudo-second order kinetic model produced a good fit with the experimental kinetic data. {yields} Equilibrium test results correlated well with the Freundlich isotherm adsorption model. {yields} The interaction between cesium ions and cement mortar was dominated by chemical adsorption. - Abstract: The adsorption of cesium on cement mortar from aqueous solutions was studied in series of bench-scale tests. The effects of cesium concentration, temperature and contact time on process kinetics and equilibrium were evaluated. Experiments were carried out in a range of initial cesium concentrations from 0.0103 to 10.88 mg L{sup -1} and temperatures from 278 to 313 K using coupons of cement mortar immersed in the solutions. Non-radioactive cesium chloride was used as a surrogate of the radioactive {sup 137}Cs. Solution samples were taken after set periods of time and analyzed by inductively coupled plasma mass spectroscopy. Depending on the initial cesium concentration, its equilibrium concentration in solution ranged from 0.0069 to 8.837 mg L{sup -1} while the respective surface concentration on coupons varied from 0.0395 to 22.34 {mu}g cm{sup -2}. Equilibrium test results correlated well with the Freundlich isotherm model for the entire test duration. Test results revealed that an increase in temperature resulted in an increase in adsorption rate and a decrease in equilibrium cesium surface concentration. Among several kinetic models considered, the pseudo-second order reaction model was found to be the best to describe the kinetic test results in the studied range of concentrations. The adsorption activation energy determined from Arrhenius equation was found to be approximately 55.9 kJ mol{sup -1} suggesting that chemisorption was the prevalent mechanism of interaction between cesium ions and cement mortar.

  7. Sympathetic cooling in a rubidium cesium mixture: Production of ultracold cesium atoms

    International Nuclear Information System (INIS)

    This thesis presents experiments for the production of ultracold rubidium cesium mixture in a magnetic trap. The long-termed aim of the experiment is the study of the interaction of few cesium atoms with a Bose-Einstein condensate of rubidium atoms. Especially by controlled variation of the cesium atom number the transition in the description of the interaction by concepts of the one-particle physics to the description by concepts of the many-particle physics shall be studied. The rubidium atoms are trapped in a magneto-optical trap (MOT) and from there reloaded into a magnetic trap. In this the rubidium atoms are stored in the state vertical stroke f=2,mf=2 right angle of the electronic ground state and evaporatively cooled by means of microwave-induced transitions into the state vertical stroke f=1,mf=1] (microwave cooling). The cesium atoms are also trppaed in a MOT and into the same magnetic trap reloaded, in which they are stored in the state vertical stroke f=4,mf=4 right angle of the electronic ground state together with rubidium. Because of the different hyperfine splitting only rubidium is evaporatively cooled, while cesium is cooled jointly sympathetically - i.e. by theramal contact via elastic collisions with rubidium atoms. The first two chapters contain a description of interatomic interactions in ultracold gases as well as a short summary of theoretical concepts in the description of Bose-Einstein condensates. The chapters 3 and 4 contain a short presentation of the methods applied in the experiment for the production of ultracold gases as well as the experimental arrangement; especially in the framework of this thesis a new coil system has been designed, which offers in view of future experiments additionally optical access for an optical trap. Additionally the fourth chapter contains an extensive description of the experimental cycle, which is applied in order to store rubidium and cesium atoms together into the magnetic trap. The last chapter

  8. Intense non-relativistic cesium ion beam

    International Nuclear Information System (INIS)

    The Heavy Ion Fusion group at Lawrence Berkeley Laboratory has constructed the One Ampere Cesium Injector as a proof of principle source to supply an induction linac with a high charge density and high brightness ion beam. This is studied here. An electron beam probe was developed as the major diagnostic tool for characterizing ion beam space charge. Electron beam probe data inversion is accomplished with the EBEAM code and a parametrically adjusted model radial charge distribution. The longitudinal charge distribution was not derived, although it is possible to do so. The radial charge distribution that is derived reveals an unexpected halo of trapped electrons surrounding the ion beam. A charge fluid theory of the effect of finite electron temperature on the focusing of neutralized ion beams (Nucl. Fus. 21, 529 (1981)) is applied to the problem of the Cesium beam final focus at the end of the injector. It is shown that the theory's predictions and assumptions are consistent with the experimental data, and that it accounts for the observed ion beam radius of approx. 5 cm, and the electron halo, including the determination of an electron Debye length of approx. 10 cm

  9. Microbial uptake of uranium, cesium, and radium

    International Nuclear Information System (INIS)

    The ability of diverse microbial species to concentrate uranium, cesium, and radium was examined. Saccharomyces cerevisiae, Pseudomonas aeruginosa, and a mixed culture of denitrifying bacteria accumulated uranium to 10 to 15% of the dry cell weight. Only a fraction of the cells in a given population had visible uranium deposits in electron micrographs. While metabolism was not required for uranium uptake, mechanistic differences in the metal uptake process were indicated. Uranium accumulated slowly (hours) on the surface of S. cerevisiae and was subject to environmental factors (i.e., temperature, pH, interfering cations and anions). In contrast, P. aeruginosa and the mixed culture of denitrifying bacteria accumulated uranium rapidly (minutes) as dense, apparently random, intracellular deposits. This very rapid accumulation has prevented us from determining whether the uptake rate during the transient between the initial and equilibrium distribution of uranium is affected by environmental conditions. However, the final equilibrium distributions are not affected by those conditions which affect uptake by S. cerevisiae. Cesium and radium were concentrated to a considerably lesser extent than uranium by the several microbial species tested. The potential utility of microorganisms for the removal and concentration of these metals from nuclear processing wastes and several bioreactor designs for contacting microorganisms with contaminated waste streams will be discussed

  10. Biosorption behavior and mechanism of cesium-137 on Rhodosporidium fluviale strain UA2 isolated from cesium solution

    International Nuclear Information System (INIS)

    In order to identify a more efficient biosorbent for 137Cs, we have investigated the biosorption behavior and mechanism of 137Cs on Rhodosporidium fluviale (R. fluviale) strain UA2, one of the dominant species of a fungal group isolated from a stable cesium solution. We observed that the biosorption of 137Cs on R. fluviale strain UA2 was a fast and pH-dependent process in the solution composed of R. fluviale strain UA2 (5 g/L) and cesium (1 mg/L). While a Langmuir isotherm equation indicated that the biosorption of 137Cs was a monolayer adsorption, the biosorption behavior implied that R. fluviale strain UA2 adsorbed cesium ions by electrostatic attraction. The TEM analysis revealed that cesium ions were absorbed into the cytoplasm of R. fluviale strain UA2 across the cell membrane, not merely fixed on the cell surface, which implied that a mechanism of metal uptake contributed largely to the cesium biosorption process. Moreover, PIXE and EPBS analyses showed that ion-exchange was another biosorption mechanism for the cell biosorption of 137Cs, in which the decreased potassium ions were replaced by cesium ions. All the above results implied that the biosorption of 137Cs on R. fluviale strain UA2 involved a two-step process. The first step is passive biosorption that cesium ions are adsorbed to cells surface by electrostatic attraction; after that, the second step is active biosorption that cesium ions penetrate the cell membrane and accumulate in the cytoplasm. - Highlights: • Microorganisms isolated from a cesium solution are considered as a biosorbent to remove cesium ions. • The biosorption equilibrium is fitted well to a Langmuir model with a correlation coefficient of 0.9997. • First attempt to explore biosorption mechanisms using PIXE and EPBS. • Living and dead microorganisms have different biosorption mechanisms. • The biosorption of 137Cs involved a two-step process: passive and active

  11. Adsorption of cesium on cement mortar from aqueous solutions.

    Science.gov (United States)

    Volchek, Konstantin; Miah, Muhammed Yusuf; Kuang, Wenxing; DeMaleki, Zack; Tezel, F Handan

    2011-10-30

    The adsorption of cesium on cement mortar from aqueous solutions was studied in series of bench-scale tests. The effects of cesium concentration, temperature and contact time on process kinetics and equilibrium were evaluated. Experiments were carried out in a range of initial cesium concentrations from 0.0103 to 10.88 mg L(-1) and temperatures from 278 to 313 K using coupons of cement mortar immersed in the solutions. Non-radioactive cesium chloride was used as a surrogate of the radioactive (137)Cs. Solution samples were taken after set periods of time and analyzed by inductively coupled plasma mass spectroscopy. Depending on the initial cesium concentration, its equilibrium concentration in solution ranged from 0.0069 to 8.837 mg L(-1) while the respective surface concentration on coupons varied from 0.0395 to 22.34 μg cm(-2). Equilibrium test results correlated well with the Freundlich isotherm model for the entire test duration. Test results revealed that an increase in temperature resulted in an increase in adsorption rate and a decrease in equilibrium cesium surface concentration. Among several kinetic models considered, the pseudo-second order reaction model was found to be the best to describe the kinetic test results in the studied range of concentrations. The adsorption activation energy determined from Arrhenius equation was found to be approximately 55.9 kJ mol(-1) suggesting that chemisorption was the prevalent mechanism of interaction between cesium ions and cement mortar.

  12. Synthesis and peculiarities of the cesium zeolite crystal structure (cesite)

    International Nuclear Information System (INIS)

    An attempt is made to synthesize cesium zeolite by introduction of amorphous seed crystals which correspond by composition with cesium-containing zeolite into the aluminosilicate gel, since this method can produce zeolite with a crystal structure it would not adopt under the usual conditions. It is seen that during crystablization upon introduction of a seed crystal the cesium content in zeolite decreases. A more complete structural elucidation of zeolite obtained by the suggested method was carried out by x0ray and IR spectral analyses. The data of x-ray analysis showed that the structures of synthesized zeolite and binary octagonal pores are similar

  13. Pollution of drug-technical materials by cesium-137

    International Nuclear Information System (INIS)

    Drug-technical raw materials are medicinal plants (flowers, folium, grasses, mushrooms, roots, fruits, berry, kidney, cortex), used in pharmacy. To limit receipt cesium-137 in people body in 1993 in the Republic of Belarus were created 'Temporary permission levels of the cesium-137 radionuclides contents in drug-technical raw materials' were created (TPL-1993). The permission levels of cesium-137 are following: for drug-technical raw material (flowers, folium, grass, mushrooms, roots and other plants parts) - 1850 Bq/kg, for dried up fruits and berries - 2590 Bq/kg. (Author)

  14. Management of cesium loaded AMP- Part I preparation of 137Cesium concentrate and cementation of secondary wastes

    International Nuclear Information System (INIS)

    Separation of 137cesium from High Level Waste can be achieved by use of composite-AMP, an engineered form of Ammonium Molybdo-Phosphate(AMP). Direct vitrification of cesium loaded composite AMP in borosilicate glass matrix leads to separation of water soluble molybdate phase. A proposed process describes two different routes of selective separation of molybdates and phosphate to obtain solutions of cesium concentrates. Elution of 137Cesium from composite-AMP by decomposing it under flow conditions using saturated barium hydroxide was investigated. This method leaves molybdate and phosphate embedded in the column but only 70% of total cesium loaded on column could be eluted. Alternatively composite-AMP was dissolved in sodium hydroxide and precipitation of barium molybdate-phosphate from the resultant solution, using barium nitrate was investigated by batch methods. The precipitation technique gave over 99.9% of 137Cesium activity in solutions, free of molybdates and phosphates, which is ideally suited for immobilization in borosilicate glass matrix. Detailed studies were carried out to immobilize secondary waste of 137Cesium contaminated barium molybdate-phosphate precipitates in the slag cement matrix using vermiculite and bentonite as admixtures. The cumulative fraction of 137Cs leached from the cement matrix blocks was 0.05 in 140 days while the 137Cs leach rate was 0.001 gm/cm2/d. (author)

  15. Structure of double hafnium and cesium sulfate

    International Nuclear Information System (INIS)

    The structure of a compound whose formula according to the structural investigation is Cssub(2+x)Hf(SOsub(4))sub(2+x)(HSOsub(4))sub(2-x)x3Hsub(2)O (x approximately 0.7) (a=10.220, b=12.004, c=15.767 A, space group Pcmn) is determined by diffractometric data (2840 reflections, anisotropic refinement, R=0.087). It is build of complex unions [Hf(SO4)4H2O]4-, Cs+ cations and water molecules. Eight O atoms surrounding Hf atom (dodecahedron Hf-O 2.10-2.22 A) belong to four sulphate groups and water molecule. Three sulphate groups are bidentate-cyclic, and one group - monodentate relative to Hf. The structure has a cesium deficit in particular positions

  16. Biosorption of uranium, radium, and cesium

    International Nuclear Information System (INIS)

    Some fundamental aspects of the biosorption of metals by microbial cells were investigated. These studies were carried out in conjunction with efforts to develop a process to utilize microbial cells as biosorbents for the removal of radionuclides from waste streams generated by the nuclear fuel cycle. It was felt that an understanding of the mechanism(s) of metal uptake would potentially enable the enhancement of the metal uptake phenomenon through environmental or genetic manipulation of the microorganisms. Also presented are the results of a preliminary investigation of the applicability of microorganisms for the removal of 137cesium and 226radium from existing waste solutions. The studies were directed primarily at a characterization of uranium uptake by the yeast, Saccharomyces cerevisiae, and the bacterium, Pseudomonas aeruginosa

  17. Atmospheric transmission for cesium DPAL using TDLAS

    Science.gov (United States)

    Rice, Christopher A.; Perram, Glen P.

    2012-03-01

    The cesium (Cs) Diode Pumped Alkali Laser (DPAL) operates near 894 nm, in the vicinity of atmospheric water vapor absorption lines. An open-path Tunable Diode Laser Absorption (TDLAS) system composed of narrow band (~300 kHz) diode laser fiber coupled to a 12" Ritchey-Chrétien transmit telescope has been used to study the atmospheric transmission characteristics of Cs DPALs over extended paths. The ruggedized system has been field deployed and tested for propagation distances of greater than 1 km. By scanning the diode laser across many free spectral ranges, many rotational absorption features are observed. Absolute laser frequency is monitored with a High Finesse wavemeter to an accuracy of less than 10 MHz. Phase sensitive detection is employed with an absorbance of less than 1% observable under field conditions.

  18. Retrospective reconstruction of Ioidne-131 distribution at the Fukushima Daiichi Nuclear Power Plant accident by analysis of Ioidne-129

    Science.gov (United States)

    Matsuzaki, Hiroyuki; Muramatsu, Yasuyuki; Toyama, Chiaki; Ohno, Takeshi; Kusuno, Haruka; Miyake, Yasuto; Honda, Maki

    2014-05-01

    Among various radioactive nuclides emitted from the Fukushima Daiichi Nuclear Power Plant (FDNPP) accident, Iodine-131 displayed high radioactivity just after the accident. Moreover if taken into human body, Iodine-131 concentrates in the thyroid and may cause the thyroid cancer. The recognition about the risk of Iodine-131 dose originated from the experience of the Chernobyl accident based on the epidemiological study [1]. It is thus important to investigate the detailed deposition distribution of I-131 to evaluate the radiation dose due to I-131 and watch the influence on the human health. However I-131 decays so rapidly (half life = 8.02 d) that it cannot be detected several months after the accident. At the recognition of the risk of I-131 on the Chernobyl occasion, it had gone several years after the accident. The reconstruction of I-131 distribution from Cs-137 distribution was not successful because the behavior of iodine and cesium was different because they have different chemical properties. Long lived radioactive isotope I-129 (half life = 1.57E+7 yr,), which is also a fission product as well as I-131, is ideal proxy for I-131 because they are chemically identical. Several studies had tried to quantify I-129 in 1990's but the analytical technique, especially AMS (Accelerator Mass Spectrometry), had not been developed well and available AMS facility was limited. Moreover because of the lack of enough data on I-131 just after the accident, the isotopic ratio I-129/I-131 of the Chernobyl derived iodine could not been estimated precisely [2]. Calculated estimation of the isotopic ratio showed scattered results. On the other hand, at the FDNPP accident detailed I-131 distribution is going to be successfully reconstructed by the systematical I-129 measurements by our group. We measured soil samples selected from a series of soil collection taken from every 2 km (or 5km, in the distant area) meshed region around FDNPP conducted by the Japanese Ministry of

  19. Fibrinogen labelling with I-131

    Energy Technology Data Exchange (ETDEWEB)

    Seminario, C.; Capillo, T.; Montanez, J. (Instituto Peruano de Energia Nuclear, Lima)

    1983-05-01

    Of the different techniques of labelling liophylized human fibrinogen, the technique of mono-chloride with modified iodine was selected. The labelling of the molecule was performed in alkali media of buffalo glycine in which the solution of stable iodine will react as well as on a later stage will the radioactive isotope. The labelling processes which were undertaken with different activities had an efficiency of over 40%; when purification with resins amberlite was carried through, in none of the cases were the impurities over 5%. Daily controls till the seventh day showed that the average values of radiochemical purity decrease were lower than 1%. The specific activity as well as the concentration of I/sup 131/, the fibrinogen and other characteristics come up to the norms of the pharmacopoeia which are applied.

  20. 14 CFR 1260.131 - Insurance coverage.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Insurance coverage. 1260.131 Section 1260... Higher Education, Hospitals, and Other Non-Profit Organizations Property Standards § 1260.131 Insurance coverage. Recipients shall, at a minimum, provide the equivalent insurance coverage for real property...

  1. 40 CFR 131.12 - Antidegradation policy.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 21 2010-07-01 2010-07-01 false Antidegradation policy. 131.12 Section 131.12 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS WATER... or social development in the area in which the waters are located. In allowing such degradation...

  2. 21 CFR 131.160 - Sour cream.

    Science.gov (United States)

    2010-04-01

    ... product. (2) Sodium citrate in an amount not more than 0.1 percent may be added prior to culturing as a... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Sour cream. 131.160 Section 131.160 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR...

  3. 40 CFR 436.131 - Specialized definitions.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Specialized definitions. 436.131 Section 436.131 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS MINERAL MINING AND PROCESSING POINT SOURCE CATEGORY Borax Subcategory §...

  4. Sorption of cesium and strontium by arid region desert soil

    International Nuclear Information System (INIS)

    Adsorption and ion exchange in soil systems are the principal mechanisms that retard the migration of nuclear waste to the biosphere. Cesium and strontium are two elements with radioactive isotopes (Cs137 and Sr90) that are commonly disposed of as nuclear waste. The sorption and ion exchange properties of nonradioactive cesium and strontium were studied in this investigation. The soil used in this study was collected at an experimental infiltration site on Frenchman Flat, a closed drainage basin on the Nevada Test Site. This soil is mostly nonsaline-alkali sandy loam and loamy sand with a cation exchange capacity ranging from 13 to 30 me/100g. The clay fraction of the soil contains illite, montmorillonite, and clinoptilolite. Ion exchange studies have shown that this soil sorbs cesium preferentially relative to strontium, and that charge for charge, the exchange-phase cations released from exchange sites exceed the cesium and strontium sorbed by the soil. 38 references, 22 figures

  5. Sorption of cesium on Olkiluoto mica gneiss, granodiorite and granite

    Energy Technology Data Exchange (ETDEWEB)

    Huitti, T.; Hakanen, M. [Univ. of Helsinki (Finland). Lab. of Radiochemistry; Lindberg, A. [Geological Survey of Finland, Espoo (Finland)

    1998-09-01

    Cesium was selected as a model to study the sorption in bedrock occurring by ion exchange mechanism. The aim of the study was to supplement the existing data on sorption occurring by ion exchange mechanism in bedrock of the candidate sites for spent fuel disposal at Olkiluoto. The sorption of cesium was studied on crushed mica gneiss, tonalite (granodiorite) and granite in artificial groundwaters. Fresh water was represented by Allard water, pH 8 and pH 7, and saline water by Ol-So water, pH 7 and pH 9. In addition, a Na-Ca-Cl brine water and its 1:10 dilution were used as simulants. Cesium concentrations were between 10{sup -8} and 10{sup -3} mol/l. The distribution coefficients of the sorption, R{sub d} and R{sub a} values were determined by batch method. Isotherms were partly non-linear with slopes 0.7 - 1.0 depending on rock and water. At the end of the sorption experiment, the water was analysed for cations exchanged for cesium. The sorption of cesium was also studied as a function of ionic strength. The ionic strength increased in the order Allard < 0l-Br 1:10 < 0l-So < 0l-Br. The sorption of cesium was lower at higher ionic strength and higher Cs concentration. The mineral composition of rocks was determined by thin section analysis, and the sorption distribution ratios on thin sections in the different waters were determined by batch technique. The minerals, that sorbed most cesium were determined by autoradiography. These were biotite, muscovite and chlorite. Cordierite in mica gneiss also sorbed cesium very effectively. (orig.) 12 refs.

  6. Adsorption Behaviour of Liquid 4He on Cesium Substrates

    OpenAIRE

    Iov, Valentin

    2004-01-01

    The aim of this thesis is to investigate the wetting properties of 4He on cesium substrates using optical and electrical methods. Due to the fact that the cesium substrates are deposited at low temperatures onto a thin silver underlayer, it is necessary firstly to study and understand the adsorption of helium on silver. The work presented here is structured as follows: some of the fundamental concepts on the theory of physisorbed films, such as van der Waals interaction, adsorption isotherms ...

  7. Seasonal variation of cesium 134 and cesium 137 in semidomestic reindeer in Norway after the Chernobyl accident

    Directory of Open Access Journals (Sweden)

    I.M. H. Eikelmann

    1990-09-01

    Full Text Available The Chernobyl accident had a great impact on the semidomestic reindeer husbandry in central Norway. Seasonal differences in habitat and diet resulted in large variations in observed radiocesium concentrations in reindeer after the Chernobyl accident. In three areas with high values of cesium-134 and cesium-137 in lichens, the main feed for reindeer in winter, reindeer were sampled every second month to monitor the seasonal variation and the decrease rate of the radioactivity. The results are based on measurements of cesium-134 and cesium-137 content in meat and blood and by whole-body monitoring of live animals. In 1987 the increase of radiocesium content in reindeer in Vågå were 4x from August to January. The mean reductions in radiocesium content from the winter 1986/87 to the winter 1987/88 were 32%, 50% and 43% in the areas of Vågå, Østre-Namdal and Lom respectively.

  8. Dicty_cDB: SSC131 [Dicty_cDB

    Lifescience Database Archive (English)

    Full Text Available SS (Link to library) SSC131 (Link to dictyBase) - - - Contig-U01312-1 SSC131E (Link... to Original site) - - - - - - SSC131E 381 Show SSC131 Library SS (Link to library) Clone ID SSC131 (Link to...ycdb.biol.tsukuba.ac.jp/CSM/SS/SSC1-B/SSC131Q.Seq.d/ Representative seq. ID SSC13...1E (Link to Original site) Representative DNA sequence >SSC131 (SSC131Q) /CSM/SS/SSC1-B/SSC131Q.Seq.d/ GTAAT...INNTNTNSMDTYGVYGNF*k** ttiiii Homology vs CSM-cDNA Score E Sequences producing significant alignments: (bits) Value SSC131 (SSC

  9. Cesium and strontium in Black Sea macroalgae

    International Nuclear Information System (INIS)

    The trace level of metals and particularly radioactive ones should be monitored to evaluate the transfer along the trophic chain, assess the risk for biota and can be used for global changes assessment. Plants respond rapidly to all changes in the ecosystem conditions and are widely used as indicators and predictors for changes in hydrology and geology. In this work we represent our successful development and applications of a methodology for monitoring of stable and radioactive strontium and cesium in marine biota (Black Sea algae's). In case of radioactive release they are of high interest. We use ED-XRF, gamma spectrometers and LSC instrumentation and only 0.25 g sample. Obtained results are compared with those of other authors in same regions. The novelty is the connection between the radioactive isotopes and their stable elements in algae in time and space scale. All our samples were collected from Bulgarian Black Sea coast. - Highlights: • An extraction chromatography method for radiochemical separation of Sr and Cs. • Assessment of Sr and Cs accumulation capacity of six Black Sea macroalgae species. • Connection between the isotopes and their stable elements content in algae. • Assessment of Sr and Cs content in ecosystems along the Bulgarian coast

  10. Radioactive Iodine (I-131) Therapy for Hyperthyroidism

    Science.gov (United States)

    ... with I-131. Depending on the amount of radioactivity administered during your treatment, your endocrinologist or radiation ... it begins destroying the gland's cells. Although the radioactivity from this treatment remains in the thyroid for ...

  11. Radiopharmaceutical potential of I-131 labelled diazepam

    International Nuclear Information System (INIS)

    In this study, diazepam is a derivative of the 1.4 benzodiazepine family that the most widely used drug as anticonvulsant agent has been labeled with I-131, as a new radiopharmaceutical and its radiopharmaceutical potential has been determined. Labeling of diazepam has been performed by iodogen method and optimum labeling conditions have been determined. Optimum reaction conditions are 1 mg for iodogen amount; 1-5 mg for diazepam amount, 15-20 minutes for reaction time and room temperature for reaction temperature. Specific activity of labeled compound was 0,15 Ci/mmol level. N-octanol/water ratio was found 1.9 for 131IDZ (131I labeled diazepam). In vivo experiments have been carried out to determine radiopharmaceutical potentials of labeled compound. Biodistribution studies on rats showed that 131IDZ have accumulated in kidneys, liver, lungs and brain tissues. Scintigraphic results taken with gamma camera on rabbits agree with biodistribution results of rats. (author)

  12. Lifetimes of Excited Levels in 131Ce

    Institute of Scientific and Technical Information of China (English)

    LI Guang-Sheng; LI Xian-Feng; WEN Li-Jun; ZHENG Yong-Nan; ZHENG Yong; LIU Yun-Zuo; YUAN Guan-Jun; YANG Chun-Xiang; MENG Rui; ZHU Li-Hua; ZHANG Zhen-Long; WANG Yue; WANG Zhi-Min; WEN Shu-Xian; LU Jing-Bin; ZHAO Guang-Yi

    2004-01-01

    @@ The fusion-evaporation reaction 116Sn (1gF, p3n) 131 Ce at projectile energy of 95 MeV is used to populate high spin states in 131 Ce. The de-exciting γ-rays are detected in γ-γ coincidence measurement with Compton-suppressed BGO-HPGe detectors. Level lifetimes of 131 Ce were determined by using the Doppler shift attenuation method.The experimental results indicate that collectivity of 131 Ce is reduced relative to that of 130 Ce and it follows that deformation decreases with increase of the neutron number on the basis of systematic comparison of transition quadrupole moments for the light cerium isotopes.

  13. 131I–Tositumomab in lymphoma

    OpenAIRE

    Cheung, M.C.; MacEachern, J.A.; Haynes, A.E.; Meyer, R.M.; Imrie, K.; ,

    2009-01-01

    Radioimmunoconjugates are radioisotope-bound monoclonal antibodies that target radiation specifically to sites of lymphoma involvement. Initial studies of 131I–tositumomab in non-Hodgkin lymphoma (nhl) have suggested benefit in patients with relapsed or refractory indolent disease. However, the routine adoption of this agent is tempered by concerns about associated toxicities and unclear long-term benefit. Based on a comprehensive search for studies on 131I–tositumomab use in lymphoma, this s...

  14. Viscosity and crystallization mechanism of cesium loaded iron phosphate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Joseph, Kitheri, E-mail: joskit@igcar.gov.in [Chemistry Group, IGCAR, Kalpakkam 603 102 (India); Kutty, K.V. Govindan [Chemistry Group, IGCAR, Kalpakkam 603 102 (India); Goswami, M.C. [National Metallurgical Laboratory, Jamshedpur 831 007 (India); Rao, P.R. Vasudeva [Chemistry Group, IGCAR, Kalpakkam 603 102 (India)

    2014-07-01

    Highlights: • Melt viscosity of cesium loaded iron phosphate glasses is measured and reported for the first time. • Viscosity – temperature followed Arrhenius model. • Activation energy of viscous flow is strongly correlated to glass transition temperature of the glasses. • Process of crystallization of cesium loaded glass by approximation-free kinetic method to understand the mechanism. • Cesium loaded IPG and IPG shows bulk crystallization mechanism. - Abstract: This paper describes the melt viscosity behaviour and the crystallization mechanism of a series of iron phosphate glasses. High temperature viscosity measurements were carried out on pristine iron phosphate glass and a series of cesium loaded iron phosphate glasses in order to understand the effect of addition of Cs{sub 2}O on viscosity of iron phosphate glasses. Activation energy of viscous flow was estimated from the experimental data by applying Arrhenius model of viscosity–temperature relationship. Activation energy of viscous flow is observed to be strongly correlated to glass transition temperature of these glasses. Fragility of iron phosphate and cesium loaded iron phosphate glass systems were also evaluated in region of high temperature. Crystallization of these glasses was studied using thermal analysis techniques. Temperature integral approximation free method was utilized to evaluate the kinetic parameters such as activation energy of crystallization (E{sub c}) and Avrami exponent (n). The value of Avrami exponent ‘n’ obtained showed that the glasses under present study crystallize via bulk crystallization mechanism, i.e., nucleation and three dimensional growth.

  15. Cesium corrosion process in Fe–Cr steel

    International Nuclear Information System (INIS)

    A cesium corrosion out-pile test was performed to Fe–Cr steel in a simulated fuel pin environment. In order to specify the corrosion products, the corroded area was analyzed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). A cesium corrosion process in Fe–Cr steel was successfully developed proceeding from both experimental results and thermochemical consideration. The corroded area was mainly formed by Fe layer and Fe depleted oxidized layer. The Fe depleted oxidized layer was formed by Cr0.5Fe0.5 and Cr2O3. The presumed main corrosion reactions were 2Cr+2/3 O2→Cr2O3(ΔG650°C=-894.1kJ/mol) and Cr23C6+46Cs+46O2→23Cs2CrO4+6C(ΔG650°C=-25018.1kJ/mol). Factors of these reactions are chromium, carbon, oxygen and cesium. Therefore, cesium corrosion progression must be dependent on the chromium content, carbon content in the steel, the supply rate of oxygen and temperature which correlated with the diffusion rate of cesium and oxygen into the specimen

  16. Viscosity and crystallization mechanism of cesium loaded iron phosphate glasses

    International Nuclear Information System (INIS)

    Highlights: • Melt viscosity of cesium loaded iron phosphate glasses is measured and reported for the first time. • Viscosity – temperature followed Arrhenius model. • Activation energy of viscous flow is strongly correlated to glass transition temperature of the glasses. • Process of crystallization of cesium loaded glass by approximation-free kinetic method to understand the mechanism. • Cesium loaded IPG and IPG shows bulk crystallization mechanism. - Abstract: This paper describes the melt viscosity behaviour and the crystallization mechanism of a series of iron phosphate glasses. High temperature viscosity measurements were carried out on pristine iron phosphate glass and a series of cesium loaded iron phosphate glasses in order to understand the effect of addition of Cs2O on viscosity of iron phosphate glasses. Activation energy of viscous flow was estimated from the experimental data by applying Arrhenius model of viscosity–temperature relationship. Activation energy of viscous flow is observed to be strongly correlated to glass transition temperature of these glasses. Fragility of iron phosphate and cesium loaded iron phosphate glass systems were also evaluated in region of high temperature. Crystallization of these glasses was studied using thermal analysis techniques. Temperature integral approximation free method was utilized to evaluate the kinetic parameters such as activation energy of crystallization (Ec) and Avrami exponent (n). The value of Avrami exponent ‘n’ obtained showed that the glasses under present study crystallize via bulk crystallization mechanism, i.e., nucleation and three dimensional growth

  17. The diffusion of cesium, strontium, and europium in silicon carbide

    Science.gov (United States)

    Dwaraknath, S. S.; Was, G. S.

    2016-08-01

    A novel multi-layer diffusion couple was used to isolate the diffusion of strontium, europium and cesium in SiC without introducing radiation damage to SiC and at concentrations below the solubility limit for the fission products in SiC. Diffusion occurred by both bulk and grain boundary pathways for all three fission products between 900∘ C and 1 ,300∘ C. Cesium was the fastest diffuser below 1 ,100∘ C and the slowest above this temperature. Strontium and europium diffusion tracked very closely as a function of temperature for both bulk and grain boundary diffusion. Migration energies ranged from 1.0 eV to 5.7 eV for bulk diffusion and between 2.2 eV and 4.7 eV for grain boundary diffusion. These constitute the first measurements of diffusion of cesium, europium, and strontium in silicon carbide, and the magnitude of the cesium diffusion coefficient supports the premise that high quality TRISO fuel should have minimal cesium release.

  18. Dissociative excitation of cesium atom upon e-CsOH collisions

    International Nuclear Information System (INIS)

    The process of dissociative excitation of cesium atom in collisions with mono-kinetic molecules of cesium hydroxide is studied. It is established that behaviour of dissociative excitations the cesium atom in spectral series corresponds of to the grade dependence of cross sections on the main quantum number of the upper level. The values of constants, characterizing the behaviour of cross sections in the eight spectral series of the cesium atom are determined

  19. Cesium in the Savannah River Site environment

    Energy Technology Data Exchange (ETDEWEB)

    Carlton, W.H.; Bauer, L.R.; Evans, A.G.; Geary, L.A.; Murphy, C.E. Jr.; Pinder, J.E.; Strom, R.N.

    1992-03-01

    Cesium in the Savannah River Site Environment is published as a part of the Radiological Assessment Program (RAP). It is the fourth in a series of eight documents on individual radioisotopes released to the environment as a result of Savannah River Site (SRS) operations. The earlier documents describe the environmental consequences of tritium, iodine, and uranium. Documents on plutonium, strontium, carbon, and technetium will be published in the future. These are dynamic documents and current plans call for revising and updating each one on a two-year schedule.Radiocesium exists in the environment as a result of above-ground nuclear weapons tests, the Chernobyl accident, the destruction of satellite Cosmos 954, small releases from reactors and reprocessing plants, and the operation of industrial, medical, and educational facilities. Radiocesium has been produced at SRS during the operation of five production reactors. Several hundred curies of [sup 137]Cs was released into streams in the late 50s and 60s from leaking fuel elements. Smaller quantities were released from the fuel reprocessing operations. About 1400 Ci of [sup 137]Cs was released to seepage basins where it was tightly bound by clay in the soil. A much smaller quantity, about four Ci. was released to the atmosphere. Radiocesium concentration and mechanisms for atmospheric, surface water, and groundwater have been extensively studied by Savannah River Technology Center (SRTC) and ecological mechanisms have been studied by Savannah River Ecology Laboratory (SREL). The overall radiological impact of SRS releases on the offsite maximum individual can be characterized by total doses of 033 mrem (atmospheric) and 60 mrem (liquid), compared with a dose of 12,960 mrem from non-SRS sources during the same period of time. Isotope [sup 137]Cs releases have resulted in a negligible risk to the environment and the population it supports.

  20. Cesium in the Savannah River Site environment

    Energy Technology Data Exchange (ETDEWEB)

    Carlton, W.H.; Bauer, L.R.; Evans, A.G.; Geary, L.A.; Murphy, C.E. Jr.; Pinder, J.E.; Strom, R.N.

    1992-03-01

    Cesium in the Savannah River Site Environment is published as a part of the Radiological Assessment Program (RAP). It is the fourth in a series of eight documents on individual radioisotopes released to the environment as a result of Savannah River Site (SRS) operations. The earlier documents describe the environmental consequences of tritium, iodine, and uranium. Documents on plutonium, strontium, carbon, and technetium will be published in the future. These are dynamic documents and current plans call for revising and updating each one on a two-year schedule.Radiocesium exists in the environment as a result of above-ground nuclear weapons tests, the Chernobyl accident, the destruction of satellite Cosmos 954, small releases from reactors and reprocessing plants, and the operation of industrial, medical, and educational facilities. Radiocesium has been produced at SRS during the operation of five production reactors. Several hundred curies of {sup 137}Cs was released into streams in the late 50s and 60s from leaking fuel elements. Smaller quantities were released from the fuel reprocessing operations. About 1400 Ci of {sup 137}Cs was released to seepage basins where it was tightly bound by clay in the soil. A much smaller quantity, about four Ci. was released to the atmosphere. Radiocesium concentration and mechanisms for atmospheric, surface water, and groundwater have been extensively studied by Savannah River Technology Center (SRTC) and ecological mechanisms have been studied by Savannah River Ecology Laboratory (SREL). The overall radiological impact of SRS releases on the offsite maximum individual can be characterized by total doses of 033 mrem (atmospheric) and 60 mrem (liquid), compared with a dose of 12,960 mrem from non-SRS sources during the same period of time. Isotope {sup 137}Cs releases have resulted in a negligible risk to the environment and the population it supports.

  1. Controllable evaporation of cesium from a dispenser oven

    Science.gov (United States)

    Fantz, U.; Friedl, R.; Fröschle, M.

    2012-12-01

    This instrument allows controlled evaporation of the alkali metal cesium over a wide range of evaporation rates. The oven has three unique features. The first is an alkali metal reservoir that uses a dispenser as a cesium source. The heating current of the dispenser controls the evaporation rate allowing generation of an adjustable and stable flow of pure cesium. The second is a blocking valve, which is fully metallic as is the body of the oven. This construction both reduces contamination of the dispenser and enables the oven to be operated up to 300 °C, with only small temperature variations (metal at a cold spot is significantly hindered. The last feature is an integral surface ionization detector for measuring and controlling the evaporation rate. The dispenser oven can be easily transferred to the other alkali-metals.

  2. Dating of mine waste in lacustrine sediments using cesium-137

    Science.gov (United States)

    Rember, W. C.; Erdman, T. W.; Hoffmann, M. L.; Chamberlain, V. E.; Sprenke, K. F.

    1993-11-01

    For over a century Medicine Lake in northern Idaho has received heavy-metal-laden tailings from the Coeur d'Alene mining district. Establishing the depositional chronology of the lake bottom sediments provides information on the source and rate of deposition of the tailings. Cesium-137, an isotope produced in the atmosphere by nuclear bomb tests, was virtually absent in the environment prior to 1951, but reached its apex in 1964. Our analysis of cesium-137 in the sediments of Medicine Lake revealed that 14 cm of fine-grained tailings were deposited in the lake from 1951 to 1964 and tailing deposition downstream was greatly reduced by the installation of tailings dams in the district in 1968. Cesium-137 analysis is accomplished by a fairly simple gamma-ray counting technique and should be a valuable tool for analyzing sedimentation in any lacustrine environment that was active during the 1950s and 1960s.

  3. Cesium 137 in oils and plants from Guatemala

    International Nuclear Information System (INIS)

    Since 1990 the project of radioactive and environmental contamination started in Guatemala. Studies about the radioactive contamination levels are made within the framework of this project. Cesium-137 has been an interest radionuclide, because it is a fission product released to the environment by the use of nuclear weapons and nuclear power plants accidents. The sampling consisted in collection of soil and grass in 20 provinces of Guatemala, one point by province, and it was made in 1990. The cesium-137 concentration in the samples, was determined by gamma spectrometry, using an hyper pure germanium detector. The results show the presence of radioactive contamination in soil and grass due to cesium-137, at levels that might be considered as normal. The levels found are not harmful for human health, and its importance is the fact that can be used as reference levels for the environmental radioactivity monitoring in Guatemala

  4. Study of radiatively sustained cesium plasmas for solar energy conversion

    Science.gov (United States)

    Palmer, A. J.; Dunning, G. J.

    1980-01-01

    The results of a study aimed at developing a high temperature solar electric converter are reported. The converter concept is based on the use of an alkali plasma to serve as both an efficient high temperature collector of solar radiation as well as the working fluid for a high temperature working cycle. The working cycle is a simple magnetohydrodynamic (MHD) Rankine cycle employing a solid electrode Faraday MHD channel. Research milestones include the construction of a theoretical model for coupling sunlight in a cesium plasma and the experimental demonstration of cesium plasma heating with a solar simulator in excellent agreement with the theory. Analysis of a solar MHD working cycle in which excimer laser power rather than electric power is extracted is also presented. The analysis predicts a positive gain coefficient on the cesium-xenon excimer laser transition.

  5. Dicty_cDB: CFD131 [Dicty_cDB

    Lifescience Database Archive (English)

    Full Text Available CF (Link to library) CFD131 (Link to dictyBase) - - - Contig-U09897-1 CFD131P (Link to Original site) CFD...131F 581 CFD131Z 205 CFD131P 786 - - Show CFD131 Library CF (Link to library) Clone ID CFD... URL http://dictycdb.biol.tsukuba.ac.jp/CSM/CF/CFD1-B/CFD131Q.Seq.d/ Representative seq. ID CFD...131P (Link to Original site) Representative DNA sequence >CFD131 (CFD131Q) /CSM/CF/CFD1-B/CFD1...QKKLIXFKVPKKIIITDNFPKTASGKIQRR FIADXLLKQQ Homology vs CSM-cDNA Score E Sequences producing significant alignments: (bits) Value CFD

  6. Hypothyroidism following 131I therapy for hyperthyroidism

    International Nuclear Information System (INIS)

    Of 890 patients who received 131I therapy for hyperthyroidism, the results of therapy were examined on 584 who could be followed up. Of these 502 (86%), were sured including 3 patients who had been completely healed after recurrence, 9 patients are still under medical treatment, and 10 died. The incidence of hypothyroidism following 131I therapy was 1.6% after 1 year, 2.3% after 2 years, 4.7% after 5 years, 15.0% after 10-12 years, 22.1% after 13-15 years and 27.5% after 16-20 years. The incidence increased constantly with the passage of time. Factors influencing the response to treatment have been investigated. As a consequence, the number of rads delivered to the thyroid gland, the gland size, and previous surgery correlated with the incidence of hypothyroidism. The number of doses of 131I, uptake and half-life of 131I in the thyroid, previous antithyroid medication, time between the onset of hyperthyroid symptoms and 131I therapy, and the age or sex of the patients appeared unrelated. The times taken to become euthyroid following a single dose of 131I were 5.6 months with 2000-4000 rads, 4.4 months with 4001-7000 rads, 4.2 months with 7001-10000 rads and 3.5 months with more than 10001 rads. The time was prolonged with decrease of rads delivered to the thyroid gland. It was found that the patients who passed through a transient hypothyroid phase in the period of three to four months after administration of 131I had a high incidence of late permanent hypothyroidism. (Evans, J.)

  7. Leukaemia incidence after iodine-131 exposure

    Energy Technology Data Exchange (ETDEWEB)

    Hall, Per (Karolinska Hospital, Stockholm (Sweden). Dept. of General Oncology); Boice, J.D. Jr. (National Cancer Inst., Bethesda, MD (United States). Div. of Cancer Etiology); Berg, Gertrud (Sahlgren' s Hospital, Gothenburg (Sweden). Dept. of General Oncology) (and others)

    1992-07-04

    Leukaemia is one of the most prominent late effects of exposure to ionising radiation. We have studied the incidence of leukaemia among 46 988 Swedish patients exposed to iodine-131 ([sup 131]I) for diagnostic reasons or to treat hyperthyroidism or thyroid cancer. The observed number of leukaemias was compared with that expected based on incidence data from the general population. The mean absorbed dose to the bone marrow was estimated as 14 mGy. 195 leukaemias occurred more than 2 years after exposure, and the standardised incidence ratio (SIR) was 1.09. Similar increased risks were seen for chronic lymphocytic leukaemia (CLL) (SIR = 1.08), a malignant condition not found to be increased after irradiation, and for non-CLL (SIR = 1.09). The risk of leukaemia did not vary by sex, age, time, or radiation dose from [sup 131]I. One reason for the absence of a radiation effect includes the possible lowering of risk when exposure is protracted over time as occurs with [sup 131]I. Excess leukaemia risks of more than 25% could thus be excluded with high assurance in this population of mainly adults. These results should be reassuring to patients exposed to [sup 131]I in medical practice and to most individuals exposed to the fall-out from the Chernobyl accident. (Author).

  8. Sorption of cesium in young till soils

    Energy Technology Data Exchange (ETDEWEB)

    Lusa, Merja; Lempinen, Janne; Ahola, Hanna; Soederlund, Mervi; Lehto, Jukka [Helsinki Univ. (Finland). Laboratory of Radiochemistry; Lahdenperae, Anne-Maj [Saanio and Riekkola Oy, Consulting Engineers, Helsinki (Finland); Ikonen, Ari T.K. [Posiva Oy, Eurajoki (Finland)

    2014-10-01

    Soil samples from three forest soil pits were examined down to a depth of approximately three metres using 1 M ammonium acetate extraction and microwave-assisted extraction with concentrated nitric acid (HNO{sub 3}), to study the binding of cesium (Cs) at Olkiluoto Island, southern Finland. Ammonium acetate was used to extract the readily exchangeable Cs fractions roughly representing the Cs fraction in soil which is available for plants. Microwave-assisted HNO{sub 3} extraction dissolves various minerals, e.g. carbonates, most sulphides, arsenides, selenides, phosphates, molybdates, sulphates, iron (Fe) and manganese (Mn) oxides and some silicates (olivine, biotite, zeolite), and reflects the total Cs concentrations. Cs was mostly found in the strongly bound fraction obtained through HNO{sub 3} extraction. The average Cs concentrations found in this fraction were 3.53 ± 0.30 mg/kg (d.w.), 3.06 ± 1.86 mg/kg (d.w.) and 1.83 ± 0.42 mg/kg (d.w.) in the three soil pits, respectively. The average exchangeable Cs found in the ammonium acetate extraction in all three sampling pits was 0.015 ± 0.008 mg/kg (d.w.). In addition, Cs concentrations in the soil solution were determined and in situ distribution coefficients (K{sub d}) for Cs were calculated. Furthermore, the in situ K{sub d} data was compared with the Cs K{sub d} data obtained using the model batch experiments. The in situ K{sub d} values were observed to fairly well follow the trend of batch sorption data with respect to soil depth, but on average the batch distribution coefficients were almost an order of magnitude higher than the in situ K{sub d} data. In situ Cs sorption data could be satisfactory fitted with the Langmuir sorption isotherm, but the Freundlich isotherm failed to fit the data. Finally, distribution coefficients were calculated by an ion exchange approach using soil solution data, the cation exchange capacity (CEC) as well as Cs to sodium (Na) and Cs to potassium (K) ion exchange selectivity

  9. Dicty_cDB: CHS131 [Dicty_cDB

    Lifescience Database Archive (English)

    Full Text Available CH (Link to library) CHS131 (Link to dictyBase) - - - Contig-U15897-1 - (Link to Original site) - - CHS1...31Z 765 - - - - Show CHS131 Library CH (Link to library) Clone ID CHS131 (Link to dicty...iol.tsukuba.ac.jp/CSM/CH/CHS1-B/CHS131Q.Seq.d/ Representative seq. ID - (Link to ...Original site) Representative DNA sequence >CHS131 (CHS131Q) /CSM/CH/CHS1-B/CHS131Q.Seq.d/ XXXXXXXXXXCAATCGA...VHA533Q) /CSM/VH/VHA5-B/VHA533Q.Seq.d/ 1491 0.0 CHS391 (CHS391Q) /CSM/CH/CHS3-D/CHS391Q.Seq.d/ 1491 0.0 CHS131 (CHS1

  10. Cesium-137 Levels Detected in Otters from Austria

    Directory of Open Access Journals (Sweden)

    Gutleb A.C.

    1991-02-01

    Full Text Available Pollution seems to be one of the most important causes for the decline of the European otter (Lutra lutra. The accident in the Chernobyl nuclear power plant added another aspect to environmental pollution. Few data on cesium-137 contents in otters are available, so levels were measured in 3 otters from Austria. All levels found were very low.

  11. Membrane-based separation technologies for cesium, strontium, and technetium

    Energy Technology Data Exchange (ETDEWEB)

    Kafka, T.

    1996-10-01

    This work is one of two parallel projects that are part of an ESP task to develop high-capacity, selective, solid extractants for cesium, strontium, and technetium from nuclear wastes. In this subtask, Pacific Northwest National Laboratory (PNNL) is collaborating with 3M, St. Paul, Minnesota, working in cooperation with IBC Advanced Technologies, American Fork, Utah.

  12. Cesium Ion Exchange Using Tank 241-AN-104 Supernate

    International Nuclear Information System (INIS)

    The River Protection Project is to design and build a high level nuclear waste treatment facility. The waste treatment plant is to process millions of gallons of radioactive waste stored in tanks at the Hanford Site. The high level nuclear waste treatment process includes various unit operations, such as ultrafiltration, precipitation, evaporation, ion exchange, and vitrification. Ion exchange is identified as the optimal treatment method for removal of cesium-137 and Tc-99 from the waste. Extensive ion exchange testing was performed using small-scale columns with actual waste samples. The objectives of this study were to: demonstrate SuperLig 644 ion exchange performance and process steps for the removal of cesium from actual AN-104 tank waste; pretreat actual AN-104 tank waste to reduce the concentration of cesium-137 in the waste below LAW vitrification limit; produce and characterize cesium eluate solutions for use in eluate evaporation tests. The experiments consisted of batch contact and small-scale column tests. The batch contact tests measured sorption partition coefficients Kds. The Kds were used to predict the effective resin capacity. The small-scale column tests, which closely mimic plant conditions, generated loading and elution profile data used to determine whether removal targets and design requirements were met

  13. Discovery of Cesium, Lanthanum, Praseodymium and Promethium Isotopes

    OpenAIRE

    May, E.; Thoennessen, M

    2011-01-01

    Currently, forty-one cesium, thirty-five lanthanum, thirty-two praseodymium, and thirty-one promethium, isotopes have been observed and the discovery of these isotopes is discussed here. For each isotope a brief synopsis of the first refereed publication, including the production and identification method, is presented.

  14. Strontium-90 and cesium-137 in fresh water

    International Nuclear Information System (INIS)

    Japan Chemical Analysis Center has analysed the strontium-90 and Cesium-137 contents in fresh water from 7 prefectures in Japan by the commission of Science and Technology Agency of Japanese Government. The method described in ''Radioactivity Survey Data in Japan No. 43 (NIRS-RSD-43, 1977) was applied to the analysis of these two radionuclides in samples. (author)

  15. Genotypic and Phenotypic Profiles of Escherichia coli Isolates Belonging to Clinical Sequence Type 131 (ST131), Clinical Non-ST131, and Fecal Non-ST131 Lineages from India

    OpenAIRE

    Hussain, Arif; Ranjan, Amit; Nandanwar, Nishant; Babbar, Anshu; Jadhav, Savita; Ahmed, Niyaz

    2014-01-01

    In view of the epidemiological success of CTX-M-15-producing lineages of Escherichia coli and particularly of sequence type 131 (ST131), it is of significant interest to explore its prevalence in countries such as India and to determine if antibiotic resistance, virulence, metabolic potential, and/or the genetic architecture of the ST131 isolates differ from those of non-ST131 isolates. A collection of 126 E. coli isolates comprising 43 ST131 E. coli, 40 non-ST131 E. coli, and 43 fecal E. col...

  16. Some aspects of cesium deposition in Transilvania (Romania)

    International Nuclear Information System (INIS)

    Following the accident of the Chernobyl atomic electric power station, a great quantity of radionuclides (∼100MCi) escaped from the reactor. It was estimated that 13% of the inventory activity of cesium representing 1.5-2 MCi left the reactor. The radioactive deposits were very nonuniform for the same distance and in the same direction from Chernobyl nuclear center having a close dependence upon direction and speed of wind and pluviometric conditions. The rains, especially the storms, spectacularly increased the radioactive fallout. Although, for the first two-three days, subsequent to accident, the meteorological conditions were favorable for Romania, after April 29/30, because of the changing in the wind direction on SW (initial it was N and NW) the countries were on this direction - Romania, Bulgaria, Greece, former Yugoslavia - began to be intensely contaminated with radioactive fallout. In Romania, the radioactive cloud passing coincided with abundant rains, especially on the direction mentioned above. On this direction, the cesium deposits are of 8-2 times larger than other Romanian regions. The torrential rain which fell on May 1st 1986, in the western side of Cluj Napoca town caused an intense contamination especially with short-life isotopes as Te, I, Ba, La, Mo. Medium and long-life isotopes as Ru, Zr, Cs, Sr were present in large quantities in this area.too. For the total contribution the value obtained was 1130 kBq/m2, much larger than the average in Romania. This work presents data about cesium content of pollen samples gathered daily between 1-30 May 1986; cesium deposits in five areas and some measurements in connection with cesium mitigation in soils

  17. 27 CFR 21.131 - Sucrose octaacetate.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Sucrose octaacetate. 21....131 Sucrose octaacetate. (a) Sucrose octaacetate is an organic acetylation product occurring as a.... Sucrose octaacetate 98 percent minimum by weight when determined by the following procedure: Transfer...

  18. Radiochromatographic Determination of 131I Labeled Eugenol

    Directory of Open Access Journals (Sweden)

    F. Zümrüt Biber Müftüler

    2015-02-01

    Full Text Available Phenolic phytochemicals are a broad class of nutraceuticals found in plants which have been extensively researched by scientists for medicinal potential. Eugenol, a phenolic natural compound available in the essential oils primarily extracted from clove plants, has been exploited for various medicinal applications. It possesses antioxidant, antimutagenic, antigenotoxic, anti-inflammatory and anticancer properties. The goal of current study was to extract Eugenol compound from clove plant and radiolabel the eugenol with 131I which is a well known radioisotope for imaging and therapy in Nuclear Medicine by utilizing iodogen method. The yield of radiolabeling of Eugenol (131I-E was calculated over 80% by Thin Layer Radio Chromatography and High Performance Liquid Radio Chromatograpy methods. Structural analysis of Eugenol was confirmed by Liguid Chromatography Mass Spectroscopy. Lipophilicity and stability studies were performed. Due to the attachment of iodine to Eugenol, radioiodinated Eugenol was more lipophilic. Stability of 131I-E was appropriate for study period. All experimental results suggest that 131I labeled Eugenol compound may be used in the applications of Nuclear Medicine as a radiolabeled agent for imaging and therapy on various cancer types.

  19. 24 CFR 886.131 - Audit.

    Science.gov (United States)

    2010-04-01

    ... assistance under this part, the audit requirements in 24 CFR part 44 shall apply. (b) Where a nonprofit... requirements of 24 CFR part 45 shall apply. ... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Audit. 886.131 Section...

  20. Radioiodine 131I metabolism in human

    International Nuclear Information System (INIS)

    Metabolic fate of orally administered 131I in human was studied. Chronological observations of whole body radioactivity distribution and thyroid 131I uptake curve revealed that 131I metabolism was greatly affected by the amount of dietary iodine intake. Under the high iodine intake exceeding 1 mg per day, uptake curve showed biphasic descending type, that is, rapid accumulation during 3 to 6 hours and rapid fall up to 48 hours and gradual decrease afterwards. While, ascending type, monophasic and maximal at 24 hours, was found universary under low iodine intake less than 500 μg per day. Thyroid function should not be affected by the amount of iodine intake, and we analysed 131I metabolism using a new four compartments which included intrathyroidal inorganic iodine pool. The results, especially hormone production rate, were found quite useful even under high iodine intake. Thyroidal organic iodine contents were calculated as approximately 2.5 mg and this value was much less than previously reported values from other countries. Administered radioiodine were mixed up with stable body iodine and reached equilibration by around 10 days. From seroimmunological, histological (microscopic and electron microscopic) studies, and irradiation studies to the cultured human thyroid cells, we concluded that this unexpected phenomenon was derived from chromosomal damage which induced gradual decrease in cell population because of inability to reproduce. Carcinogenic and genetic effects were not serious, and only three leukemic patients were reported in this country and 484 normal babies were born from 7,500 treated parents. Thus, therapeutic dose of 131I was proved rather safe, and even when exposed to radioiodine, administration of perchlorate or thiocyanate, excessive iodine and TSH seemed effective to avoid radiation injuries. (auth.)

  1. Observation of high spin levels in 131Cs from 131Ba decay

    Indian Academy of Sciences (India)

    M Sainath; Dwaraka Rani Rao; K Venkataramaniah; P C Sood

    2003-12-01

    The - and conversion electron spectra following 131Ba -decay are investigated, using HPGe detector and mini-orange electron spectrometer. Attention is particularly focussed on identifying weak transitions associated with low energy high spin levels in 131Cs level scheme earlier inferred in reaction studies but not yet observed in 131Ba decay. Our experiment identifies 15 new gammas and 6 new conversion lines in this decay. Internal conversion coefficients and multipolarities of several transitions are determined. Five new levels (3 with =7/2+ and one each with =9/2+ and 11/2-) are introduced in the 131Cs level scheme based on our observations taken together with the results from reaction studies. Spin-parity assignments to a few other levels are also suggested.

  2. Disposition of 131I proinsulin in the rat comparisons with 131I insulin

    International Nuclear Information System (INIS)

    The patterns of disposition of intravenously injected doses of 131I proinsulin and 131I insulin were compared in the rat with respect to plasma clearance, uptake, and degradation in selected organs and tissues, and rates of accumulation of degraded products in plasma and urine. The studies indicate that the differences in dose dependency in plasma clearance and degradation of 131I insulin and 131I proinsulin can be attributed to differences in relative uptakes and degradation by the liver and kidneys. The liver appeared to be the major organ involved in the removal and degradation of insulin, whereas the kidney appeared to be the major organ involved in the case of proinsulin. The hepatic process was rapid but relatively saturable, whereas the kidney process was slower but relatively unsaturable. The inverse relationship between initial concentration of hormone in plasma and uptake by liver suggests that the ratio may provide a sensitive index of the role of the liver in plasma hormone clearance

  3. Distribution and retention of cesium and strontium in Swedish boreal forest ecosystems

    International Nuclear Information System (INIS)

    The retention and distribution of cesium, and to some extent strontium, in forest environments are being studied at three sites in Sweden. The main part of the cesium found in the soil was recovered in horizons rich in organic matter. The cesium was retained in the soil organic matter in a more or less extractable form. As different soil types have a different distribution pattern of organic matter, the distribution of cesium will depend on the forest soil type. The clay content in Swedish forest soils is, in general, low which will mitigate the retention of cesium in the soil mineral horizons. The cesium and strontium present in the trees was considered to be an effect of assimilation by the tissues in the canopy as well as by the roots. The redistribution of cesium within the trees was extensive which was considered to be the effect of a high mobility of cesium in the trees. The recovery of strontium-90 in pines, in relation to the deposition rate was higher compared to the relative recovery of cesium-137, 30 years after deposition. The cesium and strontium will remain in the forest environment for a considerable time but can be reduced by forest practice, by leaching out of the soil profile or by radioactive decay

  4. 46 CFR 131.710 - Approved work vests.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Approved work vests. 131.710 Section 131.710 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OFFSHORE SUPPLY VESSELS OPERATIONS Work Vests § 131.710 Approved work vests. Each buoyant work vest carried aboard must be approved under subpart...

  5. 46 CFR 131.575 - Yearly inspections and repair.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Yearly inspections and repair. 131.575 Section 131.575..., Drills, and Inspections § 131.575 Yearly inspections and repair. (a) Each lifeboat, rescue boat, rigid... expiration date must be replaced during the annual inspection and repair if this date has passed. (d)...

  6. 46 CFR 131.935 - Prevention of oil pollution.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Prevention of oil pollution. 131.935 Section 131.935... Miscellaneous § 131.935 Prevention of oil pollution. Each vessel must be operated in compliance with— (a) Section 311 of the Federal Water Pollution Control Act, as amended (33 U.S.C. 1321); and (b) 33 CFR...

  7. Merkel cell carcinoma and iodine-131 metaiodobenzylguanidine scan

    International Nuclear Information System (INIS)

    Two cases of Merkel cell carcinoma, a neuroendocrine neoplasia of the skin, investigated with iodine, 131 metaiodobenzylguanidine (131I-mIBG) scintigraphy, are reported. Uptake in the tumor was evident only in 1 case. The possible diagnostic and therapeutic role of 131I-mIBG in patients with this rare neoplasm is discussed. (orig.)

  8. 46 CFR 131.420 - Manning and supervision.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Manning and supervision. 131.420 Section 131.420 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OFFSHORE SUPPLY VESSELS OPERATIONS Sufficiency and Supervision of Crew of Survival Craft § 131.420 Manning and supervision. (a) There must...

  9. Merkel cell carcinoma and iodine-131 metaiodobenzylguanidine scan

    Energy Technology Data Exchange (ETDEWEB)

    Castagnoli, A.; Biti, G.; De Cristofaro, M.T.R.; Papi, M.G. (Florence Univ. (Italy). Dipt. di Fisiopatologia); Ferri, P. (Florence Univ. (Italy). U.O. Medicina Nuclear USL 10D); Magrini, S.M. (Florence Univ. (Italy). U.O. Radioterapia USL 10D); Bianchi, S. (Florence Univ. (Italy). Ist. di Anatomia Patologica)

    1992-10-01

    Two cases of Merkel cell carcinoma, a neuroendocrine neoplasia of the skin, investigated with iodine, 131 metaiodobenzylguanidine ({sup 131}I-mIBG) scintigraphy, are reported. Uptake in the tumor was evident only in 1 case. The possible diagnostic and therapeutic role of {sup 131}I-mIBG in patients with this rare neoplasm is discussed. (orig.).

  10. 46 CFR 201.131 - Presentation of evidence.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 8 2010-10-01 2010-10-01 false Presentation of evidence. 201.131 Section 201.131... PRACTICE AND PROCEDURE Hearing Procedures (Rule 13) § 201.131 Presentation of evidence. (a) Testimony... specifically encouraged to cooperate with each other in joint presentations particularly in such items as...

  11. 36 CFR 406.131-406.139 - [Reserved

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false 406.131-406.139 Section 406.131-406.139 Parks, Forests, and Public Property AMERICAN BATTLE MONUMENTS COMMISSION ENFORCEMENT OF... COMMISSION §§ 406.131-406.139...

  12. 21 CFR 131.125 - Nonfat dry milk.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Nonfat dry milk. 131.125 Section 131.125 Food and... CONSUMPTION MILK AND CREAM Requirements for Specific Standardized Milk and Cream § 131.125 Nonfat dry milk. (a) Description. Nonfat dry milk is the product obtained by removal of water only from pasteurized skim milk....

  13. 21 CFR 131.120 - Sweetened condensed milk.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Sweetened condensed milk. 131.120 Section 131.120... FOR HUMAN CONSUMPTION MILK AND CREAM Requirements for Specific Standardized Milk and Cream § 131.120 Sweetened condensed milk. (a) Description. Sweetened condensed milk is the food obtained by partial...

  14. 12 CFR 225.131 - Activities closely related to banking.

    Science.gov (United States)

    2010-01-01

    ... 12 Banks and Banking 3 2010-01-01 2010-01-01 false Activities closely related to banking. 225.131 Section 225.131 Banks and Banking FEDERAL RESERVE SYSTEM (CONTINUED) BOARD OF GOVERNORS OF THE FEDERAL... Holding Companies Interpretations § 225.131 Activities closely related to banking. (a) Bank...

  15. 9 CFR 2.131 - Handling of animals.

    Science.gov (United States)

    2010-01-01

    ... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Handling of animals. 2.131 Section 2.131 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE ANIMAL WELFARE REGULATIONS Miscellaneous § 2.131 Handling of animals. (a) All licensees who maintain...

  16. 46 CFR 131.960 - Use of auto-pilot.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Use of auto-pilot. 131.960 Section 131.960 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OFFSHORE SUPPLY VESSELS OPERATIONS Miscellaneous § 131.960 Use of auto-pilot. When the automatic pilot is used in areas of high traffic...

  17. Cesium-137, a drama recounted; Cesio-137, um drama recontado

    Energy Technology Data Exchange (ETDEWEB)

    Vieira, Suzane de Alencar

    2013-01-15

    The radiological accident with Cesium-137, which started on Goiania in 1987, did not stop with the end of radiological contamination and continues in a judicial, scientific and narrative process of identification and recognition of new victims. The drama occupies a central place on the dynamics of radiological event, as it extends its limits, inflects its intensity and updates the event. As a narrative of the event, the ethnography incorporates and brings up to date the drama as an analysis landmark and the description of the theme as it is absorbed by a dramatic process. Cesium-137, a drama recounted is a textual experimentation based on real events and characters picked out from statements reported in various narratives about the radiological accident. (author)

  18. Trapping and cooling cesium atoms in a speckle field

    International Nuclear Information System (INIS)

    We present the results of two experiments where cold cesium atoms are trapped in a speckle field. In the first experiment, a YAG laser creates the speckle pattern and induces a far-detuned dipole potential which is a nearly-conservative potential. Localization of atoms near the intensity maxima of the speckle field is observed. In a second experiment we use two counterpropagating laser beams tuned close to a resonance line of cesium and in the lin perpendicular to lin configuration, one of them being modulated by a holographic diffuser that creates the speckle field. Three-dimensional cooling is observed. Variations of the temperature and of the spatial diffusion coefficient with the size of a speckle grain are presented. (orig.)

  19. Kelvin Probe Studies of Cesium Telluride Photocathode for AWA Photoinjector

    CERN Document Server

    Wisniewski, Eric; Yusof, Zikri; Spentzouris, Linda; Terry, Jeff; Harkay, Katherine

    2012-01-01

    Cesium telluride is an important photocathode as an electron source for particle accelerators. It has a relatively high quantum efficiency (>1%), is sufficiently robust in a photoinjector, and has a long lifetime. This photocathode is grown in-house for a new Argonne Wakefield Accelerator (AWA) beamline to produce high charge per bunch (~50 nC) in a long bunch train. Here, we present a study of the work function of cesium telluride photocathode using the Kelvin Probe technique. The study includes an investigation of the correlation between the quantum efficiency and the work function, the effect of photocathode aging, the effect of UV exposure on the work function, and the evolution of the work function during and after photocathode rejuvenation via heating.

  20. Cesium exchange reaction on natural and modified clinoptilolite zeolites

    International Nuclear Information System (INIS)

    Cesium cation exchange reaction with K, Na, Ca and Mg ions on natural and modified clinoptilolite has been studied. Batch cation-exchange experiments were performed by placing 0.5 g of clinoptilolite into 10 ml or 20 ml of 1 x 10-3M CsCl solution for differing times. Two type deposits of clinoptilolite zeolites from, Nizny Hrabovec (NH), Slovakia and Metaxades (MX), Greece were used for ion-exchange study. The distribution coefficient (Kd) and sorption capacity (Γ) were evaluated. For the determination of K, Na, Ca and Mg isotachophoresis method, the most common cations in exchange reaction was used. Cesium sorption was studied using 137Cs tracer and measured by γ-spectrometry. (author)

  1. Spectrally selective optical pumping in Doppler-broadened cesium atoms

    International Nuclear Information System (INIS)

    The D1 line spectrally selective pumping process in Doppler-broadened cesium is analyzed by solving the optical Bloch equations. The process, described by a three-level model with the Λ scheme, shows that the saturation intensity of broadened atoms is three orders of magnitude larger than that of resting atoms. The |Fg = 3> → |Fe = 4> resonance pumping can result in the ground state |Fg = 4, mF = 4> sublevel having a maximum population of 0.157 and the population difference would be about 0.01 in two adjacent magnetic sublevels of the hyperfine (HF) state Fg = 4. To enhance the anisotropy in the ground state, we suggest employing dichromatic optical HF pumping by adding a laser to excite D1 line |Fg = 4> → |Fe = 3> transition, in which the cesium magnetometer sensitivity increases by half a magnitude and is unaffected by the nonlinear Zeeman effect even in Earth's average magnetic field. (atomic and molecular physics)

  2. Fiber laser system for cesium and rubidium atom interferometry

    CERN Document Server

    Diboune, Clément; Bidel, Yannick; Cadoret, Malo; Bresson, Alexandre

    2016-01-01

    We present an innovative fiber laser system for both cesium and rubidium manipulation. The architecture is based on frequency conversion of two lasers at 1560 nm and 1878 nm. By taking advantage of existing fiber components at these wavelengths, we demonstrate an all fiber laser system delivering 350 mW at 780 nm for rubidium and 210 mW at 852 nm for cesium. This result highlights the promising nature of such laser system especially for Cs manipulation for which no fiber laser system has been reported. It offers new perspectives for the development of atomic instruments dedicated to onboard applications and opens the way to a new generation of atom interferometers involving three atomic species $^{85}$Rb, $^{87}$Rb and $^{133}$Cs for which we propose an original laser architecture.

  3. Studies on the Separation of Cesium From Fission Products

    Institute of Scientific and Technical Information of China (English)

    QIANLi-juan; ZHANGSheng-dong; GUOJing-ru; CUIAn-zhi; YANGLei; WUWang-suo

    2003-01-01

    135Cs is a long-life fission product. When measuring its thermal cross section, we must separate radiochemical purity cesium from fission products. Except for decontaminating radio- nuclides, others which can be activated must be avoided to come into solution. So ion exchanger is used. Inorganic ion exchangers have received increased attention because of their high resistance to radiation and their very efficient separation of alkali metal ions.

  4. Optimized production of a cesium Bose-Einstein condensate

    OpenAIRE

    Kraemer, Tobias; Herbig, Jens; Mark, Michael; Weber, Tino; Chin, Cheng; Naegerl, Hanns-Christoph; Grimm, Rudolf

    2004-01-01

    We report on the optimized production of a Bose-Einstein condensate of cesium atoms using an optical trapping approach. Based on an improved trap loading and evaporation scheme we obtain more than $10^5$ atoms in the condensed phase. To test the tunability of the interaction in the condensate we study the expansion of the condensate as a function of scattering length. We further excite strong oscillations of the trapped condensate by rapidly varying the interaction strength.

  5. Radioactive cesium. Dynamics and transport in forestal food-webs

    International Nuclear Information System (INIS)

    This report summarises results from a radioecological study during 1994-1995 concerning turnover, redistribution and loss of radioactive Cesium (134 and 137) in boreal forest ecosystems, as well as uptake and transfer in important food-chains over moose, vole and vegetation. The basis for this report are 9 publications published 1994-95. These reports are presented in summary form. 9 refs, 17 figs

  6. Electrically switched cesium ion exchange. FY 1997 annual report

    International Nuclear Information System (INIS)

    This paper describes the Electrically Switched Ion Exchange (ESIX) separation technology being developed as an alternative to ion exchange for removing radionuclides from high-level waste. Progress in FY 1997 for specific applications of ESIX is also outlined. The ESIX technology, which combines ion exchange and electrochemistry, is geared toward producing electroactive films that are highly selective, regenerable, and long lasting. During the process, ion uptake and elution can be controlled directly by modulating the potential of an ion exchange film that has been electrochemically deposited onto a high surface area electrode. This method adds little sodium to the waste stream and minimizes the secondary wastes associated with traditional ion exchange techniques. Development of the ESIX process is well underway for cesium removal using ferrocyanides as the electroactive films. Films having selectivity for perrhenate (a pertechnetate surrogate) over nitrate also have been deposited and tested. Based on the ferrocyanide film capacity, stability, rate of uptake, and selectivity shown during performance testing, it appears possible to retain a consistent rate of removal and elute cesium into the same elution solution over several load/unload cycles. In batch experiments, metal hexacyanoferrate films showed high selectivities for cesium in concentrated sodium solutions. Cesium uptake was unaffected by Na/Cs molar ratios of up to 2 x 104 , and reached equilibrium within 18 hours. During engineering design tests using 60 pores per inch, high surface area nickel electrodes, nickel ferrocyanide films displayed continued durability. losing less than 20% of their capacity after 1500 load/unload cycles. Bench-scale flow system studies showed no change in capacity or performance of the ESIX films at a flow rate up to 13 BV/h, the maximum flow rate tested, and breakthrough curves further supported once-through waste processing. 9 refs., 24 figs

  7. Corrections to our results for optical nanofiber traps in Cesium

    CERN Document Server

    Ding, D; Choi, K S; Kimble, H J

    2012-01-01

    Several errors in Refs. [1, 2] are corrected related to the optical trapping potentials for a state-insensitive, compensated nanofiber trap for the D2 transition of atomic Cesium. Section I corrects our basic formalism in Ref. [1] for calculating dipole-force potentials. Section II corrects erroneous values for a partial lifetime and a transition wavelength in Ref. [1]. Sections III and IV present corrected figures for various trapping configurations considered in Refs. [1] and [2], respectively.

  8. Radiosensitizers action on Iodine 131 therapeutical effect

    International Nuclear Information System (INIS)

    Present studies were aimed to research the possible application of a radiosensitizer, nicotinamide, to increase the therapeutical effect of radioiodine. There were used goitrous and normal rats with growing dose of Iodine 131, with and without simultaneous treatment with nicotinamide. The obtained results show that the nicotinamide treatment importantly increases the thyroid radio destructive effect induced by radioiodine. Under these experimental conditions, nicotinamide induces to a significant increase of thyroid vascularisation, without changes in the proteins ADP-ribosylation activity. These results show, for the first time, the radiosensitizer effect of nicotinamide in front of Iodine 131 and give the possibility of using it in the treatment of hyperthyroid or thyroid difference cancer patients. (author)

  9. Test procedures and instructions for Hanford complexant concentrate supernatant cesium removal using CST

    Energy Technology Data Exchange (ETDEWEB)

    Hendrickson, D.W.

    1997-01-08

    This document provides specific test procedures and instructions to implement the test plan for the preparation and conduct of a cesium removal test, using Hanford Complexant Concentrate supernatant liquor from tank 241-AN-107, in a bench-scale column. The cesium sorbent to be tested is crystalline silicotitanate. The test plan for which this provides instructions is WHC-SD-RE-TP-023, Hanford Complexant Concentrate Supernatant Cesium Removal Test Plan.

  10. Test procedures and instructions for Hanford tank waste supernatant cesium removal

    Energy Technology Data Exchange (ETDEWEB)

    Hendrickson, D.W., Westinghouse Hanford

    1996-05-31

    This document provides specific test procedures and instructions to implement the test plan for the preparation and conduct of a cesium removal test using Hanford Double-Shell Slurry Feed supernatant liquor from tank 251-AW-101 in a bench-scale column.Cesium sorbents to be tested include resorcinol-formaldehyde resin and crystalline silicotitanate. The test plan for which this provides instructions is WHC-SD-RE-TP-022, Hanford Tank Waste Supernatant Cesium Removal Test Plan.

  11. A monitor of airborne 131I

    International Nuclear Information System (INIS)

    An experimental study was conducted of the designing problems of a monitor for air contamination by 131I, i.e., choice of the detector, optimization of the configuration of the adsorbent-detector system, choice of the pump and the interaction of the pump and the adsorbent. A comparison was made of beta and gamma detectors suitable for 131I monitoring. The background was determined for each detector and their sensitivity determined using a 131I source of known activity. The relative sensitivity of the individual detectors was calculated with regard to detector SKW U 04. The ambient area of the SKG-1 detector (45 mm diameter by 50 mm thick) was scanned using a 131I point detector (1x1 mm) to assess the effect of adsorbent shape, size and location on detector efficiency, and the dependence of the sensitivity of well-type scintillators on the position of the source along the well axis was determined. The pumping characteristics of four different pumps are given, i.e., the dependence of the volume flow rate of pumped air on the pressure loss at the pump inlet, the dependence of pressure losses on the flow rate of pumped air for selected adsorption materials, and the values of the specific resistance of filtration materials. Based on the experiments, two monitor designs are suggested, one portable and the other stationary. The portable monitor is equipped with a semiconductor PSC detector and a diaphragm pump, and filtration paper impregnated with activated carbon is used as the adsorbent. The stationary monitor uses a transversely bored 60 mm diameter by 50 mm thick NaI(Tl) crystal. The adsorbent bed is located in the crystal's through-hole which is 16.5 mm in diameter. A stationary air-pump is used. (B.S.)

  12. MODELING RESULTS FROM CESIUM ION EXCHANGE PROCESSING WITH SPHERICAL RESINS

    Energy Technology Data Exchange (ETDEWEB)

    Nash, C.; Hang, T.; Aleman, S.

    2011-01-03

    Ion exchange modeling was conducted at the Savannah River National Laboratory to compare the performance of two organic resins in support of Small Column Ion Exchange (SCIX). In-tank ion exchange (IX) columns are being considered for cesium removal at Hanford and the Savannah River Site (SRS). The spherical forms of resorcinol formaldehyde ion exchange resin (sRF) as well as a hypothetical spherical SuperLig{reg_sign} 644 (SL644) are evaluated for decontamination of dissolved saltcake wastes (supernates). Both SuperLig{reg_sign} and resorcinol formaldehyde resin beds can exhibit hydraulic problems in their granular (nonspherical) forms. SRS waste is generally lower in potassium and organic components than Hanford waste. Using VERSE-LC Version 7.8 along with the cesium Freundlich/Langmuir isotherms to simulate the waste decontamination in ion exchange columns, spherical SL644 was found to reduce column cycling by 50% for high-potassium supernates, but sRF performed equally well for the lowest-potassium feeds. Reduced cycling results in reduction of nitric acid (resin elution) and sodium addition (resin regeneration), therefore, significantly reducing life-cycle operational costs. These findings motivate the development of a spherical form of SL644. This work demonstrates the versatility of the ion exchange modeling to study the effects of resin characteristics on processing cycles, rates, and cold chemical consumption. The value of a resin with increased selectivity for cesium over potassium can be assessed for further development.

  13. Cesium Toxicity Alters MicroRNA Processing and AGO1 Expressions in Arabidopsis thaliana.

    Directory of Open Access Journals (Sweden)

    Il Lae Jung

    Full Text Available MicroRNAs (miRNAs are short RNA fragments that play important roles in controlled gene silencing, thus regulating many biological processes in plants. Recent studies have indicated that plants modulate miRNAs to sustain their survival in response to a variety of environmental stimuli, such as biotic stresses, cold, drought, nutritional starvation, and toxic heavy metals. Cesium and radio-cesium contaminations have arisen as serious problems that both impede plant growth and enter the food chain through contaminated plants. Many studies have been performed to define plant responses against cesium intoxication. However, the complete profile of miRNAs in plants during cesium intoxication has not been established. Here we show the differential expression of the miRNAs that are mostly down-regulated during cesium intoxication. Furthermore, we found that cesium toxicity disrupts both the processing of pri-miRNAs and AGONOUTE 1 (AGO1-mediated gene silencing. AGO 1 seems to be especially destabilized by cesium toxicity, possibly through a proteolytic regulatory pathway. Our study presents a comprehensive profile of cesium-responsive miRNAs, which is distinct from that of potassium, and suggests two possible mechanisms underlying the cesium toxicity on miRNA metabolism.

  14. Laboratory plant for the separation of cesium from waste solutions of the PUREX process

    International Nuclear Information System (INIS)

    A laboratory plant for the separation of cesium from a fission product waste solution of the fuel reprocessing is described. The plant consists of two stages. In the first stage cesium is adsorbed on ammonium molybdatophosphate (AMP). Then the adsorbent is dissolved. From the solution cesium is adsorbed on a cationic ion exchanger in the second stage. Then AMP can be reproduced from this solution. For the elution of cesium in the second stage a NH4NO3 solution (3 m) is used. Flow sheet, construction and the control device of the plant are described and the results of tests with a model solution are given. (author)

  15. Structure of cesium loaded iron phosphate glasses: An infrared and Raman spectroscopy study

    International Nuclear Information System (INIS)

    The structure of cesium loaded iron phosphate glasses (IPG) was investigated using infrared and Raman spectroscopy. The spectra of the cesium doped samples revealed a structural modification of the parent glass owing to the incorporation of cesium. The structural changes could be correlated with the variation observed in the glass transition temperature of these glasses. Increased Cs-mediated cationic cross linking appears to be the reason for the initial rise in glass transition temperature up to 21 mol% Cs2O in IPG; while, breakdown of the phosphate network with increasing cesium content, brings down the glass transition temperature.

  16. Mobility of cesium through the Callovo-Oxfordian claystones under partially saturated conditions

    International Nuclear Information System (INIS)

    The diffusion of cesium was studied in an unsaturated core of Callovo-Oxfordian claystone, which is a potential host rock for retrievable disposal of high-level radioactive wastes. In-diffusion laboratory experiments were performed on rock samples with water saturation degrees ranging from 81% to 100%. The analysis of both cesium concentration monitoring in the source reservoir and postmortem cesium rock concentration profile of the samples was carried out using a chemical-transport code where the sorption of cesium was described by a multi-site ion-exchange model. The results showed that cesium exhibited a clear trend related to the saturation degree of the sample. The more dehydrated the rock sample, the slower the decrease of cesium concentration, and the thinner the penetration depth of cesium was. The effective diffusion coefficient (De) for cesium decreased from 18.5 *10-11 m2 s-1 at full-saturation to 0.3 * 10-11 m2 s-1 for the more dehydrated sample. This decrease is almost 1 order of magnitude higher than that for tritiated water (HTO), although a similar behavior could have been expected, since cesium is known to diffuse in the same parts of the pore space as HTO in fully saturated claystones. (authors)

  17. Cesium transport in Four Mile Creek of the Savannah River Plant

    International Nuclear Information System (INIS)

    The behavior of a large radioactive cesium release to a Savannah River Plant (SRP) stream was examined using a stable cesium release to Four Mile Creek. Measurements following the release show that most of the cesium released was transported downstream; however, sorption and desorption decreased the maximum concentration and increased the travel time and duration, relative to a dye tracer, at sampling stations downstream. The study was made possible by the development of an analytical technique using ammonium molybdophosphate and neutron activation that permitted the measurement of stable cesium concentrations as low as 0.2 μg/L

  18. Preparation of Modified Kaolin Filler with Cesium and Its Application in Security Paper

    OpenAIRE

    Houssni El-Saied; Samya El-Sherbiny; Omnia Ali; Wafaa El-Saied; Said Rohyem

    2013-01-01

    In this study, cesium was added intentionally during paper manufacture for protecting the papers against forgery and counterfeiting by sorbing cesium ions (Cs+) on kaolin, used as special filler in papermaking. The sorption of cesium from aqueous solution by kaolin was studied as a function of pH, shaking time, cesium initial concentration, and mass of kaolin using batch technique. The results showed that a solution containing 10 mg/L Cs+ and 250 mg of kaolin at pH 6 can be used to modify the...

  19. Labelling of meta-iodobenzylguanidine with iodine-131 (I-131-MIBG) for adrenal gland diagnosis

    International Nuclear Information System (INIS)

    Labelling of meta-iodobenzylguanidine with iodine-131 (I-131 MIBG, for adrenal gland diagnosis has been studied. The MIBG was synthesized from the reaction of meta-iodobenzylamine hydrochloride with cyanamide and labelled with iodine-131 by isotope exchange method using copper(II) as a catalyst. The percentage of labelling was about 98%, with a specific activity of 1.5-2.0 mCi/mg. The radiochemical purity was found to be greater than 99%. Biodistribution studies were performed on mice, the results showed great affinity for the adrenal gland uptake with highest radioactivity after 1 day of injection. The stability of the product with 1% benzyl alcohol was 7 days upon storing at 40C

  20. Analysis of transfer of 131I and 137Cs deposited after the Chernobyl accident via the grass-cow-milk pathway and comparison with parameters in use with food chain models

    International Nuclear Information System (INIS)

    A variety of measurements of activity concentrations of 131I and 137Cs in cows feed and milk after the Chernobyl accident are compiled and evaluated using the concepts of linear compartmental theory. Minimal compartmental models derived from the various data sets showed no unique structure. Differences, however, could be attributed to limited observation times of experimental data. Calculated weathering half-lives of both isotopes and equilibrium transfer coefficients of cesium are well within the range of data collected from laboratory experiments using fodder contaminated superficially, whereas calculated transfer coefficients of iodine are in the lower range of data reported from laboratory experiments. (19 refs., 1 fig., 3 tabs.)

  1. Cesium-137 inventories in undisturbed areas in different regions of Brazil

    International Nuclear Information System (INIS)

    Cesium-137 is an anthropogenic radionuclide introduced in the environment in the early of 1960s to the end of 1970s. The Cesium-137 has very used to assess soil redistribution in the landscape because this is very tight in the fine soil particles and its movement in the landscape is due to soil redistribution. To use Cesium-137 to assess soil redistribution is need to known the Cesium-137 inventory in an area that not has experimented soil erosion neither soil deposition. So, this work present Cesium-137 inventories in undisturbed areas in different regions of Brazil, from South to Northeast of Brazil. The inventories in these areas represent the variational deposition of Cesium-137 in the whole national territory of Brazil. The inventories of Cesium-137 varied from 200 ± 15 Bq.m-2 for South region to 15 ± 2 Bq.m-2 for Northeast region. Moreover, was verified that the Cesium- 137 inventories depend on latitude and altitude of the area. (author)

  2. Peculiarities of presence of cesium-137 in soil at Azgir test site grounds

    International Nuclear Information System (INIS)

    The granulometric composition of soil and the distribution of cesium-137 by soil fractions at the Azgir test site was determined. The characterization of cesium-137 presence in the layer of the thickness of 1 cm of the surface soil was gave. (author)

  3. Velocity Distribution of Effective Atoms in a Small Optically Pumped Cesium Beam Frequency Standard

    Institute of Scientific and Technical Information of China (English)

    CHEN Jingbiao; WANG Fengzhi; YANG Donghai; WANG YiQiu

    2001-01-01

    In this paper, the velocity distribution of effective atoms in a small optically pumped cesium beam frequency standard has been achieved from the Fourier transforms of the experimentally recorded Ramsey patterns. The result fits well with the theoretical calculation. The second order Doppler shift correction of the small cesium atomic clock is obtained from the velocity distribution of effective atoms.

  4. Vacuum squeezed light for atomic memories at the D2 cesium line

    CERN Document Server

    Burks, Sidney; Giacobino, Elisabeth; Laurat, Julien; Ortalo, Jérémie; Jia, Xiaojun; Villa, Fabrizio; Chuimmo, Antonino

    2008-01-01

    We report the experimental generation of squeezed light at 852 nm, locked on the Cesium D2 line. 50% of noise reduction down to 50 kHz has been obtained with a doubly resonant optical parametric oscillator operating below threshold, using a periodically-polled KTP crystal. This light is directly utilizable with Cesium atomic ensembles for quantum networking applications

  5. Ionizing mechanisms in a cesium plasma irradiated with a ruby laser

    Science.gov (United States)

    Shimada, K.; Robinson, L. B.

    1975-01-01

    A cesium filled diode--laser plasmadynamic converter was built to investigate the feasibility of converting laser energy to electrical energy at large power levels. Experiments were performed with a pulsed ruby laser to determine the quantity of electrons and cesium ions generated per pulse of laser beam and to determine the output voltage. A current density as high as 200 amp/sq cm from a spot of approximately 1 sq mm area and an open circuit voltage as high as 1.5 volts were recorded. A qualitative theory was developed to explain these results. In the operation of the device, the laser beam evaporates some of the cesium and ionizes the cesium gas. A dense cesium plasma is formed to absorb further the laser energy. Results suggest that the simultaneous absorption of two ruby laser photons by the cesium atoms plays an important role in the initial ionization of cesium. Inverse bremsstrahlung absorption appears to be the dominant mechanism in subsequent processes. Recombinations of electrons and cesium ions appear to compete favorably with the simultaneous absorption of two photons.

  6. Methodology to administer therapeutic dose of I-131; Metodologia para administrar dosis terapeutica de I-131

    Energy Technology Data Exchange (ETDEWEB)

    Basteris M, J.; Gomez D, R. [Universidad Autonoma de Yucatan, Facultad de Medicina, Merida, Yucatan (Mexico)

    2007-07-01

    The present work suggests the use of measures guided to eliminate the resulting chronic sialoadenitis of the treatment of the thyroid cancer with Iodine-131, as well as the use of citric fruits to stimulate the salivation, the post-dose administration of liquids to accelerate the gastric emptying avoiding the secondary effects as the vomit is included. (Author)

  7. Disposition of /sup 131/I proinsulin in the rat comparisons with /sup 131/I insulin

    Energy Technology Data Exchange (ETDEWEB)

    Izzo, J.L.; Roncone, A.M.; Helton, D.L.; Izzo, M.J.

    1978-04-01

    The patterns of disposition of intravenously injected doses of /sup 131/I proinsulin and /sup 131/I insulin were compared in the rat with respect to plasma clearance, uptake, and degradation in selected organs and tissues, and rates of accumulation of degraded products in plasma and urine. The studies indicate that the differences in dose dependency in plasma clearance and degradation of /sup 131/I insulin and /sup 131/I proinsulin can be attributed to differences in relative uptakes and degradation by the liver and kidneys. The liver appeared to be the major organ involved in the removal and degradation of insulin, whereas the kidney appeared to be the major organ involved in the case of proinsulin. The hepatic process was rapid but relatively saturable, whereas the kidney process was slower but relatively unsaturable. The inverse relationship between initial concentration of hormone in plasma and uptake by liver suggests that the ratio may provide a sensitive index of the role of the liver in plasma hormone clearance.

  8. Sorption of iodine, chlorine, technetium and cesium in soil

    International Nuclear Information System (INIS)

    The safety assessment of final disposal of spent nuclear fuel will include an estimate for the behavior of waste nuclides in the biosphere. As a part of this estimate also the sorption of radioactive iodine, chlorine, technetium and cesium in soil is to be considered. The chemistry and the sorption of these radionuclides in soils are described in this literature survey. Behavior of I-129, Cl-36 and Tc-99 in the environment is of great interest because of their long half-lives and relatively high mobilities. The importance of Cs-135 arises from its high content in spent nuclear fuel and long physical half-life, even though it is considered relatively immobile in soil. Factors affecting the migration and sorption of radionuclides in soils can be divided into elemental and soil specific parameters. The most important elemental factor is the speciation of the element, which is influenced by the soil redox potential, pH and complex forming ligands. Soil micro-organisms can either serve as sorbents for radionuclides or affect their speciation by altering the prevailing soil redox conditions. Soil organic matter content and mineral properties have a marked influence on the retention of radionuclides. The sorption of anionic radionuclides such as I-, Cl- and TcO4 - is pronounced in the presence of organic matter. Clay minerals are known to bound cesium effectively. The effect of speciation of radioactive iodine, chlorine, technetium and cesium in soil is considered in this study, as well as the effect of soil micro-organisms, organic matter and mineral properties. (orig.)

  9. Cesium-137 inventory of the undisturbed soil areas in the Londrina Region, Parana, Brazil

    International Nuclear Information System (INIS)

    Cesium-137 is an artificial radionuclide introduced in the environment through the radioactive fallout of the superficial tests of nuclear weapons. The cesium-137 deposition occurred to middles of the 1980-decade and, due to the Chernobyl accident, great part of Europe had a additional fallout of cesium-137. The contaminations of this accident do not have reached Southern Hemisphere. Cesium-137 is an alkaline metal, high electropositive, that in contact with the soil is strongly adsorbed to the clay in the FES (Frayed Edge Sites) and RES (Regular Edge Sites) positions, and it movement by chemical processes in the soil is insignificant. Because of this, cesium-137 became a good soil marker, and its movement is related to the soil movement particles, so that the cesium-137 have been used in the study of the soil redistribution processes, as a tool of quantifying the rates of soil losses and gain. To use this methodology, it is necessary the knowledge of the reference inventory of cesium-137, that is given as function of the total concentration of cesium-137 deposited in an area by the radioactive fallout. If a sampling point presents less cesium-137 than the reference inventory, this point is considered a point with soil loss; otherwise, the point is considered a point with soil deposition. To evaluate the cesium-137 inventory in the Londrina region, four areas of the undisturbed soil were sampling in grid of 3x3, with a distance of 9 meters among the points. Of these four sampling areas, three areas were of native forest (labeled Mata1, Mata2 and Mata UEL), and one was a pasture area. Cesium-137 inventory was 223 ± 41 Bq m-2, 240 ± 65 Bq m-2 and 305 ± 36 Bq m-2 for Mata UEL, Mata1 and Mata2, respectively, and of 211 ± 28 Bq m-2 for the native pasture. Considering the deviation in each value, it is not possible to conclude that there are differences among the values of cesium-137 inventory, so that the average reference inventory of cesium-137 for the Londrina

  10. A study of iodine, cesium, and strontium sorption on alkali-earth hydro-phosphates from the aqueous phase

    International Nuclear Information System (INIS)

    Full text of publication follows: The amount of radioactive species penetrating into the environment because of human activities has been increasingly growing. The most biologically dangerous nuclear-fuel fission products are iodine, cesium, and strontium radionuclides, which can sorb from aqueous solutions on various natural objects, including apatite minerals. This work studied the sorption of 131I-, 131IO3-137Cs+ and 85Sr2+ ions of various samples of Ca, Sr, and Ba hydro-phosphates. The samples of alkali-earth hydro-phosphates (AEHP) were synthesized by the following reactions: MCl2 + Na3PO4 + NaOH → M5(PO4)3OH↓; MCl2 + NH4OH + (NH4)2HPO4 → M5(PO4)3OH↓; MCl2 + NaOH + (NH4)2HPO4 → M5(PO4)3OH↓ (where M is Ca, Sr, or Ba). The experiments on a study of the sorption of 131I-, 131IO3-137Cs+, and 85Sr2+ ions on AEHP from aqueous solutions of KI, KIO3, CsNO3, or Sr(NO3)2 were carried out using the following procedure. A calculated amount of the target AEHP was added upon mixing to a 1.10-5 mg/dm3 water solution (200 ml) of KI, KIO3, CsNO3, or Sr(NO3)2 containing the radionuclides 131I, 137Cs, and 85Sr. The calculation of the AEHP was carried out based on the condition that the ratio between the volume of the liquid and the weight of the solid phase V/m was equal to 500 or 200 ml/g. The suspension was actively mixed over the necessary period of time, and the precipitate was then filtered off. The precipitate on the filter was washed two times with 50-ml portions of water, which were merged in one fraction with the filtered matter. Following that, the concentrations of 131I, 137Cs and 85Sr radionuclides in the solution and precipitate were measured using a gamma spectrometric study. Using the known V/m ratio and the distribution of radionuclides between the solid and liquid phases, the distribution coefficient Kd was calculated by the formula: Kd = V/m . I1/I2, where I1 and I2 are the concentrations of radionuclides in the solid and liquid phases, respectively

  11. Rational Design of Cesium-Selective Ionophores and Chemosensors: Dihydrocalix[4]arene Crown-6 Ethers

    Energy Technology Data Exchange (ETDEWEB)

    Sachleben, Richard A.; Bryan, Jeffrey C.; Brown, Gilbert M.; Engle, Nancy L.; Haverlock, Tamara J.; Hay, Benjamin P.; Urvoas, Agathe; Moyer, Bruce A.

    2003-12-15

    Molecular mechanics calculations performed on calix[4]arene crown-6 ethers predict that the 1,3-dihydro derivatives will exhibit greater complementarity for potassium and cesium ions than the parent 1,3-dialkoxy calix crowns. The X-ray crystal structures of 1,3-alt bis-octyloxycalix[4]arene benzocrown-6 ether, dihydrocalix[4]arene benzocrown-6 ether, and the cesium nitrate complex of dihydrocalix[4]arene benzocrown-6 ether were determined. The cesium complex structure corresponds closely to the structure predicted by molecular mechanics. The dihydrocalix[4]arene crown-6 ethers exhibit enhanced cesium selectivity in the extraction of alkali metal salts and provide a platform for a highly sensitive and selective cesium chemosensor.

  12. [Variation in amount of radioactive cesium before and after cooking dry shiitake and beef].

    Science.gov (United States)

    Nabeshi, Hiromi; Tsutsumi, Tomoaki; Hachisuka, Akiko; Matsuda, Rieko

    2013-01-01

    We investigated the change of radioactive cesium content in food due to cooking in order to estimate the internal radiation exposure due to from radioactive materials in food. Our results revealed that soaking dry shiitake in water decreased the radioactive cesium content by about 50%, compared with that present in uncooked shiitake. Radioactive cesium in beef was decreased by about 10%, 12%, 60-65% and 80% by grilling, frying, boiling and stewing, respectively, compared to uncooked beef. For cooked beef, the decrease in the ratio of radioactive cesium was significantly different among the types of cooking. The decrease ratio of radioactive cesium in boiled and stewed beef was 8 times higher than that in grilled and fried beef.

  13. Sensitive Detection of Cold Cesium Molecules by Radiative Feshbach Spectroscopy

    OpenAIRE

    Chin, Cheng; Kerman, Andrew J.; Vuletić, Vladan; Chu, Steven

    2002-01-01

    We observe the dynamic formation of $Cs_2$ molecules near Feshbach resonances in a cold sample of atomic cesium using an external probe beam. This method is 300 times more sensitive than previous atomic collision rate methods, and allows us to detect more than 20 weakly-coupled molecular states, with collisional formation cross sections as small as $\\sigma =3\\times 10^{-16}$cm$^2$. We propose a model to describe the atom-molecule coupling, and estimate that more than $2 \\times 10^5$ $Cs_2$ mo...

  14. Characterizing optical dipole trap via fluorescence of trapped cesium atoms

    Institute of Scientific and Technical Information of China (English)

    LIU; Tao; GENG; Tao; YAN; Shubin; LI; Gang; ZHANG; Jing; WANG; Junmin; PENG; Kunchi; ZHANG; Tiancai

    2006-01-01

    Optical dipole trap (ODT) is becoming an important tool of manipulating neutral atoms. In this paper ODT is realized with a far-off resonant laser beam strongly focused in the magneto-optical trap (MOT) of cesium atoms. The light shift is measured by simply monitoring the fluorescence of the atoms in the magneto-optical trap and the optical dipole trap simultaneously. The advantages of our experimental scheme are discussed, and the effect of the beam waist and power on the potential of dipole trap as well as heating rate is analyzed.

  15. Cesium fallout in Norway after the Chernobyl accident

    International Nuclear Information System (INIS)

    Results of country-wide measurements of 137Cs and 134 Cs in soil samples in Norway after the Chernobyl accident are reported. The results clearly demonstrates that municipalities in the central part of southern Norway, Troendelag and the southern part of Nordland, have been rather heavily contaminated. The total fallout of 137Cs and 134Cs from the Chernobyl accident in Norway is estimated to 2300 TBq and 1200 TBq, respectively. This is approximately 6% of the cesium activity released from the reactor

  16. Transfer of orally administrated iodine-131 into chicken eggs

    Energy Technology Data Exchange (ETDEWEB)

    Uenak, Turan E-mail: unak@sci.ege.edu.tr; Yildirim, Yeliz; Avcibasi, U.; Cetinkaya, Berkan; Uenak, G

    2003-03-01

    Radioactive iodine-131 as both as free iodide (Na{sup 131}I) and covalently bound to aniline (aniline-{sup 131}I) was added to the drinking water of two Leghorn laying hens as a single dose and also as a cumulative dose over 1 week. The radioactivity of the principal parts of the eggs, i.e. shell, white, and yolk, was measured, and the radioactivity levels per gram material, and percent of the total radioactivity were calculated. The radioactivity measurements were continued for 1 month following the administration of {sup 131}I. In the case of the single dose administration, the results obtained showed that about 15% of the total radioactivity administered as Na{sup 131}I was transported into the egg structure; compared to only about 1% for aniline-{sup 131}I. After cumulative administration, about 15% of the total administered radioactivity was transported into the egg structure with both forms of {sup 131}I. This was probably because of metabolic cleavage of iodine bonds in the labeled aniline molecules during the longer period of exposure. These results also showed considerable accumulation of {sup 131}I in the egg yolks. In the case of the single dose administration, {sup 131}I can be detected in eggs up to about 20 days after administration, and up to about 30 days, in the case of the cumulative administration over 1 week.

  17. Morphological and electrical properties of zirconium vanadate doped with cesium

    Directory of Open Access Journals (Sweden)

    Marwa F. Elkady

    2014-09-01

    Full Text Available Cesium doped zirconium vanadate ZrV2O7 with different Cs dopant content (Cs/Zr varied from 0 to 0.5 in weight ratio were fabricated by hydrothermal technique at 120 °C for 60 min. The synthesized materials are thermally treated using microwave technique. The structural and morphological properties of the synthesized materials and thermally treated samples were investigated using XRD and SEM respectively. It was evident that all synthesized specimens have cubic phase structural without any extra phase but after heat treatment Orthorhombic phase appear with doped samples. However, the morphological structure of the doped synthesized materials has transferred from nanoparticles into rods aspect with heat treatment for the different dopant ratio. Moreover, the electrical properties of both the synthesized and thermally treated materials are studied by AC impedance measurements. The results indicated that the ionic conductivity of Cs-doped ZrV2O7 materials decreased by increasing the dopant ratio while that thermally treated samples the ionic conductivity increase by increasing the dopant ratio. Finally, the concentration of cesium dopants is found to play crucial role in tuning the morphology and electrical properties of nanostructures.

  18. Transportable cesium irradiator (TPCI): Final safety analysis report: Revision 1

    International Nuclear Information System (INIS)

    This Final Safety Analysis Report describes the Transportable Cesium Irradiator (TPCI) and assesses the hazards associated with its operation. The TPCI consists of a mobile, lead-shielded, irradiation unit with support equipment mounted within an enclosed trailer. The irradiation unit has two basic compartments; a source chamber sized to mate with the transportation cask which houses the source capsules, and an irradiation chamber formed as a large shielded cylinder (drum) with a window. The irradiation chamber is mounted on a large diameter support bearing. As this chamber is rotated its window moves from the product access door, where produce is inserted or extracted, to a position in line with a similar window in the source chamber. When the windows are aligned the produce is irradiated, while the back wall of the irradiation chamber shields the product access door. The TPCI is designed to be transported throughout the continental United States. The transportation cask containing the cesium source capsules is transported separately from the irradiation unit and is installed when the TPCI unit has been readied for operation at a particular site. The transportation cask is a separate unit and is documented in a separate FSAR

  19. Kelvin probe studies of cesium telluride photocathode for AWA photoinjector

    Energy Technology Data Exchange (ETDEWEB)

    Wisniewski, Eric E., E-mail: ewisniew@anl.gov [High Energy Physics Division, Argonne National Laboratory, 9700 S. Cass, Lemont, IL 60439 (United States); Physics Department, Illinois Institute of Technology, 3300 South Federal Street, Chicago, IL 60616 (United States); Velazquez, Daniel [High Energy Physics Division, Argonne National Laboratory, 9700 S. Cass, Lemont, IL 60439 (United States); Physics Department, Illinois Institute of Technology, 3300 South Federal Street, Chicago, IL 60616 (United States); Yusof, Zikri, E-mail: zyusof@hawk.iit.edu [High Energy Physics Division, Argonne National Laboratory, 9700 S. Cass, Lemont, IL 60439 (United States); Physics Department, Illinois Institute of Technology, 3300 South Federal Street, Chicago, IL 60616 (United States); Spentzouris, Linda; Terry, Jeff [Physics Department, Illinois Institute of Technology, 3300 South Federal Street, Chicago, IL 60616 (United States); Sarkar, Tapash J. [Rice University, 6100 Main, Houston, TX 77005 (United States); Harkay, Katherine [Accelerator Science Division, Argonne National Laboratory, 9700 S. Cass, Lemont, IL 60439 (United States)

    2013-05-21

    Cesium telluride is an important photocathode as an electron source for particle accelerators. It has a relatively high quantum efficiency (>1%), is sufficiently robust in a photoinjector, and has a long lifetime. This photocathode is grown in-house for a new Argonne Wakefield Accelerator (AWA) beamline to produce high charge per bunch (≈50nC) in a long bunch train. Here, we present a study of the work function of cesium telluride photocathode using the Kelvin probe technique. The study includes an investigation of the correlation between the quantum efficiency and the work function, the effect of photocathode aging, the effect of UV exposure on the work function, and the evolution of the work function during and after photocathode rejuvenation via heating. -- Highlights: ► The correlation between Quantum Efficiency (QE) and work function. ► How QE and work function evolve together. ► Rejuvenation of the photocathode via heating and the effect on work function. ► The effects on the work function due to exposure to UV light.

  20. Structure and bonding in crystalline cesium uranyl tetrachloride under pressure.

    Science.gov (United States)

    Osman, Hussien H; Pertierra, Pilar; Salvadó, Miguel A; Izquierdo-Ruiz, F; Recio, J M

    2016-07-21

    A thorough investigation of pressure effects on the structural properties of crystalline cesium uranyl chloride was performed by means of first-principles calculations within the density functional theory framework. Total energies, equilibrium geometries and vibrational frequencies were computed at selected pressures up to 50 GPa. Zero pressure results present good agreement with available experimental and theoretical data. Our calculated equation of state parameters reveal that Cs2UO2Cl4 is a high compressible material, similar to other ionic compounds with cesium cations, and displays a structural anisotropic behavior guided by the uranyl moiety. An unexpected variation of the U-O bond length, dUO, is detected as pressure is applied. It leads to a dUO-stretching frequency relationship that cannot be described by the traditional Badger's rule. Interestingly enough, it can be explained in terms of a change in the main factor controlling dUO. At low pressure, the charge transferred to the uranyl cation induces an increase of the bond length and a red shift of the stretching frequencies, whereas it is the mechanical effect of the applied pressure above 10 GPa that is the dominant factor that leads to a shortening of dUO and a blue shift of the stretching frequencies. PMID:27340008

  1. Spectrally selective optical pumping in Doppler-broadened cesium atoms

    Institute of Scientific and Technical Information of China (English)

    Zhang Jun-Hai; Zeng Xian-Jin; Li Qing-Meng; Huang Qiang; Sun Wei-Min

    2013-01-01

    The D1 line spectrally selective pumping process in Doppler-broadened cesium is analyzed by solving the optical Bloch equations.The process,described by a three-level model with the A scheme,shows that the saturation intensity of broadened atoms is three orders of magnitude larger than that of resting atoms.The |Fg =3> → |Fe-4> resonance pumping can result in the ground state |Fg =4,mF =4> sublevel having a maximum population of 0.157 and the population difference would be about 0.01 in two adjacent magnetic sublevels of the hyperfine (HF) state Fg =4.To enhance the anisotropy in the ground state,we suggest employing dichromatic optical HF pumping by adding a laser to excite D1 line |Fg =4> → |Fe =3>transition,in which the cesium magnetometer sensitivity increases by half a magnitude and is unaffected by the nonlinear Zeeman effect even in Earth's average magnetic field.

  2. Structure and bonding in crystalline cesium uranyl tetrachloride under pressure.

    Science.gov (United States)

    Osman, Hussien H; Pertierra, Pilar; Salvadó, Miguel A; Izquierdo-Ruiz, F; Recio, J M

    2016-07-21

    A thorough investigation of pressure effects on the structural properties of crystalline cesium uranyl chloride was performed by means of first-principles calculations within the density functional theory framework. Total energies, equilibrium geometries and vibrational frequencies were computed at selected pressures up to 50 GPa. Zero pressure results present good agreement with available experimental and theoretical data. Our calculated equation of state parameters reveal that Cs2UO2Cl4 is a high compressible material, similar to other ionic compounds with cesium cations, and displays a structural anisotropic behavior guided by the uranyl moiety. An unexpected variation of the U-O bond length, dUO, is detected as pressure is applied. It leads to a dUO-stretching frequency relationship that cannot be described by the traditional Badger's rule. Interestingly enough, it can be explained in terms of a change in the main factor controlling dUO. At low pressure, the charge transferred to the uranyl cation induces an increase of the bond length and a red shift of the stretching frequencies, whereas it is the mechanical effect of the applied pressure above 10 GPa that is the dominant factor that leads to a shortening of dUO and a blue shift of the stretching frequencies.

  3. A study of strontium and cesium sorption on granite

    International Nuclear Information System (INIS)

    The diffusion and sorption of cesium and strontium in crushed granite particles is discussed. Sorption experiments have been performed with one granite from Finnsjoen outside Forsmark on the east coast of Sweden and one granite from the Stripa mine in central Sweden. Granite samples have been crushed and screened, and six different particle size fractions from 0.10-0.12 mm to 4-5 mm of each rock have been used in the experiments. The initial concentrations of inactive cesium and strontium were 10-15 ppm. The experimental data indicate that the amount of sorption is dependent not only on the mass of granite particles, but also to some extent on the size of the particles. An attempt has been made to distinguish between sorption on external surfaces and inner surfaces. The amount of external surface adsorption was found to vary from 15-40 % of the total adsorption capacity for the particle size fraction 0.10-0.12 mm to a few percent or less for the largest particles used. (Auth.)

  4. Diffusion of strontium, technetium, iodine and cesium in granitic rock

    International Nuclear Information System (INIS)

    The migration of strontium, technetium, iodine and cesium in granitic rock has been studied. Rock samples were taken from drilling cores in granitic and granodioritic rock, and small (2x2x2 cm) rock tablets from the drilling cores were exposed to a groundwater solution containing one of the studied elements at trace levels. The concentration of the element versus penetration depth in the rock tablet was measured radiometrically. The sorption on the mineral faces and the diffusion into the rock were studied by an autoradiographic technique. The cationic strontium and cesium have apparent diffusivities of 10-13 - 10-14 m2/s. The migration is confined to microfissures or filled fractures containing e.g., calcite, epidote or chlorite or in veins with high capacity minerals (e.g. biotite). The anionic iodine and technetium have apparent diffusivities of about 10-14 m2/s. These species migrate along mineral boundaries and in open fractures and to a minor extent in high capacity mineral veins. (orig.)

  5. Studies on cesium sorption in hydrous zirconium and titanium oxides

    International Nuclear Information System (INIS)

    Significant quantities of 137Cs (T1/2 = 30.1 y) and 90Sr (T1/2 = 28.5 y) are produced as fission products in nuclear reactors. These long-lived gamma-emitting radionuclides, regarded as a waste few decades ago, are being termed now as valuables owing to the upsurge in the utilization of these radioisotopes in the area of medicine, food irradiation, and sewage treatment technologies in recent years. For long-term waste management it is necessary to minimize the volume and toxicity of the waste. Selective recovery and utilization of these radionuclides from the waste is the concept of growing interest to many researchers. Inorganic sorbents are proven candidates for the separation and recovery of cesium and strontium from aqueous waste streams. They are chemically durable and stable against ionizing radiation. In addition, these materials can be converted into unleachable ceramic form for final disposal. Hydrous metal oxides belong to a particular class of inorganic ion exchangers extensively investigated for various applications in nuclear waste treatment. The present study deals with the preparation of hydrous zirconium and titanium oxide and the studies aimed at separation of cesium from aqueous wastes

  6. I-131 HIPPURAN FOR THE ESTIMATION OF RENAL PLASMA-FLOW - REQUIREMENTS FOR RADIOCHEMICAL PURITY

    NARCIS (Netherlands)

    KENGEN, RAM; MEIJER, S; VANZANTEN, AK; BEEKHUIS, H; KOSTERINK, JGW; PIERS, DA

    1995-01-01

    For many years iodide-131 Hippuran has been used as a tracer to measure effective renal plasma flow (ERPF). Because of the low renal clearance of free I-131-iodide and the inability to count it separately from I-131-Hippuran, free I-131-iodide will lower the calculated I-131-Hippuran clearance, resu

  7. Equilibrium, kinetic and thermodynamic study of cesium adsorption onto nanocrystalline mordenite from high-salt solution.

    Science.gov (United States)

    Lee, Keun-Young; Park, Minsung; Kim, Jimin; Oh, Maengkyo; Lee, Eil-Hee; Kim, Kwang-Wook; Chung, Dong-Yong; Moon, Jei-Kwon

    2016-05-01

    In this study, the equilibrium, kinetics and thermodynamics of cesium adsorption by nanocrystalline mordenite were investigated under cesium contamination with high-salt solution, simulating the case of an operation and decommissioning of nuclear facilities or an accident during the processes. The adsorption rate constants were determined using a pseudo second-order kinetic model. The kinetic results strongly demonstrated that the cesium adsorption rate of nano mordenite is extremely fast, even in a high-salt solution, and much faster than that of micro mordenite. In the equilibrium study, the Langmuir isotherm model fit the cesium adsorption data of nano mordenite better than the Freundlich model, which suggests that cesium adsorption onto nano mordenite is a monolayer homogeneous adsorption process. The obtained thermodynamic parameters indicated that the adsorption involved a very stable chemical reaction. In particular, the combination of rapid particle dispersion and rapid cesium adsorption of the nano mordenite in the solution resulted in a rapid and effective process for cesium removal without stirring, which may offer great advantages for low energy consumption and simple operation. PMID:26683820

  8. Scintigraphic depiction of an insulinoma by I-131 metaiodobenzylguanidine

    Energy Technology Data Exchange (ETDEWEB)

    Geatti, O.; Shapiro, B.; Barillari, B. (Istituto di Medicina Nucleare, Ospedale Civile di Udine (Italy))

    1989-12-01

    Scintigraphy with I-131 metaiodobenzylguanidine (MIBG) was effective in depicting a pancreatic insulinoma in a patient suffering from intermittent hypoglycemia. This observation widens the range of neuroendocrine tumors that take up to I-131 MIBG and supports the concept that many tumors of the amine precursor uptake and decarboxylation system may be imaged in this way.

  9. 46 CFR 131.940 - Marine sanitation device.

    Science.gov (United States)

    2010-10-01

    ... Miscellaneous § 131.940 Marine sanitation device. Each vessel with installed toilet facilities must have a marine sanitation device in compliance with 33 CFR part 159. ... 46 Shipping 4 2010-10-01 2010-10-01 false Marine sanitation device. 131.940 Section...

  10. 7 CFR 457.131 - Macadamia nut crop insurance provisions.

    Science.gov (United States)

    2010-01-01

    ...) regulations, 7 CFR part 400, subpart G, and applicable policy provisions unless damage or changes to the... 7 Agriculture 6 2010-01-01 2010-01-01 false Macadamia nut crop insurance provisions. 457.131... INSURANCE CORPORATION, DEPARTMENT OF AGRICULTURE COMMON CROP INSURANCE REGULATIONS § 457.131 Macadamia...

  11. Chemical and physical quality control of the HIPPURAN-131I

    International Nuclear Information System (INIS)

    Some physico-chemical methods for analytical control of Hippuran-131I are compared. The most convenient to applicate in hospitals and in more specialized quality control laboratories are recommended. The quality of Hippuran-131I produced by ISOTOP (USSR) is also evaluated. The product met the requirement of the International Pharmacopeia

  12. 40 CFR 164.131 - Review by Administrator.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Review by Administrator. 164.131 Section 164.131 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS RULES OF PRACTICE GOVERNING HEARINGS, UNDER THE FEDERAL INSECTICIDE, FUNGICIDE, AND RODENTICIDE...

  13. Renal 131I-hippuran extraction in man

    DEFF Research Database (Denmark)

    Hutchings, M; Hesse, B; Grønvall, J;

    2002-01-01

    This study examined the 131I-hippuran extraction fraction during baseline renal blood flow rates and at high flow rates induced by dopamine.......This study examined the 131I-hippuran extraction fraction during baseline renal blood flow rates and at high flow rates induced by dopamine....

  14. Carcinoid tumor of the thymus visualized with I 131-MIBG

    International Nuclear Information System (INIS)

    Iodine 131 Metaiodobenzylguanidine is usually used in the diagnosis of pheochromocytoma, neuroblastoma and bronchus and gut carcinoid tumors. This radiopharmaceutical is sometimes applied in therapy. We report the case of a patient with an exceptional carcinoid tumor of the thymus studied by I 131-MIBG scintigraphy before and after surgery. The results are in agreement with the other investigations

  15. 45 CFR 96.131 - Treatment services for pregnant women.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 1 2010-10-01 2010-10-01 false Treatment services for pregnant women. 96.131... Substance Abuse Prevention and Treatment Block Grant § 96.131 Treatment services for pregnant women. (a) The State is required to, in accordance with this section, ensure that each pregnant woman in the State...

  16. I-131-MIBG therapy: aspects of radiation protection

    International Nuclear Information System (INIS)

    In this short article the radiation protection during treatment of children with 131I-MIBG is described. A treatment of up to 200 mCi 131I-MIBG is safe. The dose equivalent of assisting parents stays under 3 mSv. The medical personnel receives at most 0.1 mSv during the administration. 3 refs

  17. 49 CFR 209.131 - Criminal penalties generally.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Criminal penalties generally. 209.131 Section 209... Criminal Penalties § 209.131 Criminal penalties generally. A person who knowingly violates 49 U.S.C. 5104(b... hazardous material transportation law or a regulation, order, special permit, or approval issued...

  18. 21 CFR 155.131 - Canned field corn.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Canned field corn. 155.131 Section 155.131 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION CANNED VEGETABLES Requirements for Specific Standardized Canned Vegetables §...

  19. Scintigraphic depiction of an insulinoma by I-131 metaiodobenzylguanidine

    International Nuclear Information System (INIS)

    Scintigraphy with I-131 metaiodobenzylguanidine (MIBG) was effective in depicting a pancreatic insulinoma in a patient suffering from intermittent hypoglycemia. This observation widens the range of neuroendocrine tumors that take up to I-131 MIBG and supports the concept that many tumors of the amine precursor uptake and decarboxylation system may be imaged in this way

  20. Dose assessment of medical staff taking care of patients treated with 131I due to the intake of 131I

    International Nuclear Information System (INIS)

    Aim: Legislation requires that patient receiving 131I in activities greater than 550MBq have to be hospitalized in special closed department. Medical staff taking care of these patients can be exposed to external irradiation and internal contamination with 131I. The aim of this study was to assess the annual effective dose of medical staff taking care of patients treated with 131I due to the occupational intake of 131I. Material - Medical Staff: 6 nurses took care of 6 patients (placed into two rooms) treated with 131I in activities between 550 and 1100 MBq. 131I was normally delivered to patients once per week. After patients received 131I nurses were in contact with patients in average 4 hours per day, 4 days per week. Methods: Direct Method - whole body counting (WBC) of staff was performed daily after they finished their work and indirect method - determination of air 131I concentration in patient's rooms (AC) were used to assess the intake of 131I by staff. Measurements were done in winter period.Results and Dose Assessment: Results of measurements of medical staff and determination of 131I air concentration are presented. Average daily 131I intake of staff assessed from WBC results was 315 Bq; average daily 131I air concentration for first four days was 35 Bq/m3. Assessment of annual effective dose due to the internal contamination (realistic approach): - Direct method: 315 Bq/day x 208 days/year x 7,6 Sv/Bq x 10-9 = 0,498 mSv/year. - Indirect method: 35 Bq/m3 x 1,5 m3/hour x 832 hours/year x 7,6 Sv/Bq x 10-9 = 0,332 mSv/year. Conclusion: Medical staff taking care of patients treated with 131I received effective dose less than 0,5 mSv/year due to the intake of 131I. In the some time period they received 1,65 to 2,24 mSv due to the exposure to the external radiation coming from patients treated with 131I

  1. Toxicity of upfront 131I-metaiodobenzylguanidine (131I-MIBG) therapy in newly diagnosed neuroblastoma patients: a retrospective analysis

    International Nuclear Information System (INIS)

    In the treatment of patients with high-risk neuroblastoma, different doses of 131I-metaiodobenzylguanidine (131I-MIBG) are administered at different time points during treatment. Toxicity, mainly haematological (thrombocytopenia), from 131I-MIBG therapy is known to occur in extensively chemotherapy pretreated neuroblastoma patients. Up to now, acute toxicity from 131I-MIBG as initial treatment has never been studied in a large cohort. The aim of this retrospective study was to document acute toxicity related to upfront 131I-MIBG. All neuroblastoma patients (stages 1-4 and 4S) treated upfront with 131I-MIBG at the Emma Children's Hospital, Academic Medical Centre (1992 - 2008) were included in this retrospective analysis. The acute toxicity (during therapy) and short-term toxicity (1st month following therapy) of the first two 131I-MIBG therapies were studied. Of 66 patients (34 boys, 32 girls; median age 2.2 years, range 0.1 - 9.4 years), 49 had stage 4 disease, 5 stage 4S, 6 stage 3, 1 stage 2 and 5 stage 1. The median first dose was 441 MBq/kg (range 157 - 804 MBq/kg). The median second dose was 328 MBq/kg (range 113 - 727 MBq/kg). The most frequently observed symptoms were nausea and vomiting (21 %, maximum grade II). The main toxicity was grade IV haematological, occurring only in stage 4 patients, after the first and second 131I-MIBG therapies: anaemia (5 % and 4 %, respectively), leucocytopenia (3 % and 4 %) and thrombocytopenia (2 % and 4 %). No stem cell rescue was needed. The main acute toxicity observed was haematological followed by nausea and vomiting. One patient developed posterior reversible encephalopathy syndrome during 131I-MIBG therapy, possibly related to 131I-MIBG. We consider 131I-MIBG therapy to be a safe treatment modality. (orig.)

  2. Preliminary Evaluation of Cesium Distribution for Wet Sieving Process Planned for Soil Decontamination in Japan - 13104

    Energy Technology Data Exchange (ETDEWEB)

    Enokida, Y.; Tanada, Y.; Hirabayashi, D. [Graduate School of Engineering, 1 Furo-cho Nagoya-shi, Aichi-ken, 4648603 (Japan); Sawada, K. [EcoTopia Science Institute, Nagoya University, 1 Furo-cho Nagoya-shi, Aichi-ken, 4648603 (Japan)

    2013-07-01

    For the purpose of decontaminating radioactive cesium from a huge amount of soil, which has been estimated to be 1.2x10{sup 8} m{sup 3} by excavating to a 5-cm depth from the surface of Fukushima Prefecture where a severe nuclear accident occurred at TEPCO's power generating site and has emitted a significant amount of radioactive materials, mainly radioactive cesium, a wet sieving process was selected as one of effective methods available in Japan. Some private companies have demonstrated this process for soil treatment in the Fukushima area by testing at their plants. The results were very promising, and a full-fledged application is expected to follow. In the present study, we spiked several aqueous samples containing soil collected from an industrial wet sieving plant located near our university for the recycling of construction wastes with non-radioactive cesium hydroxide. The present study provides scientific data concerning the effectiveness in volume reduction of the contaminated soil by a wet sieving process as well as the cesium distribution between the liquid phase and clay minerals for each sub-process of the full-scale one, but a simulating plant equipped with a process of coagulating sedimentation and operational safety fundamentals for the plant. Especially for the latter aspect, the study showed that clay minerals of submicron size strongly bind a high content of cesium, which was only slightly removed by coagulation with natural sedimentation (1 G) nor centrifugal sedimentation (3,700 G) and some of the cesium may be transferred to the effluent or recycled water. By applying ultracentrifugation (257,000 G), most of submicron clay minerals containing cesium was removed, and the cesium amount which might be transferred to the effluent or recycled water, could be reduced to less than 2.3 % of the original design by the addition of a cesium barrier consisting of ultracentrifugation or a hollow fiber membrane. (authors)

  3. Hydrogen and Cesium Monitor for H- Magnetron Sources

    Energy Technology Data Exchange (ETDEWEB)

    Tan, Cheng-Yang [Fermilab; Bollinger, Dan [Fermilab; Schupbach, Brian [Fermilab; Seiya, Kiyomi [Fermilab

    2014-07-01

    The relative concentration of cesium to hydrogen in the plasma of a H- magnetron source is an important parameter for reliable operations. If there is too much cesium, the surfaces of the source become contaminated with it and sparking occurs. If there is too little cesium then the plasma cannot be sustained. In order to monitor these two elements, a spectrometer has been built and installed on a test and operating source that looks at the plasma. It is hypothesized that the concentration of each element in the plasma is proportional to the intensity of their spectral lines.

  4. Effect of Rare Earth Elements on Exchange Performances of Cesium Ion-Sieve

    Institute of Scientific and Technical Information of China (English)

    张惠源; 王榕树; 林灿生; 张先业

    2003-01-01

    The exchange performances and the distribution coefficient of Cesium Ion-Sieve (Cs-IS) for cesium and for some rare earth elements were compared. In particular, the effects of neodymium on the cesium ion exchange and the Cs+ selectivity variation on Cs-IS owing to introduction of rare earth elements into HLLW were studied. Though rare earth elements exhibit a small influence on the distribution coefficient for Cs+, they impair Cs-exchange capacity of Cs-IS to some extent. This interruption on the selectivity to Cs+ can be significantly eliminated provided an appropriate ratio of liquid to solid V:m is used.

  5. High voltage holding in the negative ion sources with cesium deposition

    Energy Technology Data Exchange (ETDEWEB)

    Belchenko, Yu.; Abdrashitov, G.; Ivanov, A.; Sanin, A.; Sotnikov, O., E-mail: O.Z.Sotnikov@inp.nsk.su [Budker Institute of Nuclear Physics, Siberian Branch of Russian Academy of Sciences, Novosibirsk (Russian Federation)

    2016-02-15

    High voltage holding of the large surface-plasma negative ion source with cesium deposition was studied. It was found that heating of ion-optical system electrodes to temperature >100 °C facilitates the source conditioning by high voltage pulses in vacuum and by beam shots. The procedure of electrode conditioning and the data on high-voltage holding in the negative ion source with small cesium seed are described. The mechanism of high voltage holding improvement by depletion of cesium coverage is discussed.

  6. Specific interaction of cesium with the surface of calcium silicate hydrates

    International Nuclear Information System (INIS)

    The sorption of cesium at the calcium silicate hydrates (CSH) surface was investigated, both through sorption isotherm data and by solid-state NMR experiments. The sorption ability of CSH towards cesium is favored for low solid Ca/Si molar ratios, in agreement with the negative surface charge they develop then. A significant proportion of these sorbed cesium cations remains tightly bound to the surface sites forming, in dehydrated CSH, inner-sphere complexes, which can not be removed by alcohol washing. Chloride seems to present a lower affinity for CSH, even for high Ca/Si molar ratios, where the surface charge becomes positive. (orig.)

  7. First-principles study of cesium adsorption to weathered micaceous clay minerals

    Science.gov (United States)

    Okumura, Masahiko; Nakamura, Hiroki; Machida, Masahiko

    2014-05-01

    A large amount of radioactive nuclides was produced into environment due to the Fukushima Dai-ichi Nuclear Power Plant (FDNPP) accident. Residents near FDNPP were suffering from radioactive cesium and then evacuated, because which has long half-life and is retained by surface soil for long time. The Japanese government has been decontaminating the cesium by removing the surface soil in order to return them to their home. This decontamination method is very effective, but which produces huge amount of waste soil. This becomes another big problem in Fukushima, because it is not easy to find large storage sites. Then effective and economical methods to reduce the volume of the waste soil are needed. However, it has not been invented yet. One of the reasons is lack of knowledge about microscopic process of adsorption/desorption of cesium to/from soil. It is known that weathered micaceous clay minerals play crucial role on adsorption and retention of cesium. They are expected to have special sorption sites, called frayed edge sites (FESs), which adsorb cesium selectively and irreversibly. Properties of FES have been intensely investigated by experiments. But microscopic details of the adsorption process on FES are still unclear. Because direct observation of the process with current experimental techniques is quite difficult. We investigated the adsorption of cesium to FES in muscovite, which is a typical micaceous clay mineral, via first-principles calculations (density functional theory). We made a minimal model of FES and evaluate the energy difference before and after cesium adsorption to FES. This is the first numerical modeling of FES. It was shown that FES does adsorb cesium if the weathering of muscovite has been weathered. In addition, we revealed the mechanism of cesium adsorption to FES, which is competition between ion radius of cesium and the degree of weathering. I plan to discuss volume reduction of the waste soil based on our result. Reference M. Okumura

  8. Test procedures and instructions for single shell tank saltcake cesium removal with crystalline silicotitanate

    Energy Technology Data Exchange (ETDEWEB)

    Duncan, J.B.

    1997-01-07

    This document provides specific test procedures and instructions to implement the test plan for the preparation and conduct of a cesium removal test, using Hanford Single Shell Tank Saltcake from tanks 24 t -BY- I 10, 24 1 -U- 108, 24 1 -U- 109, 24 1 -A- I 0 1, and 24 t - S-102, in a bench-scale column. The cesium sorbent to be tested is crystalline siticotitanate. The test plan for which this provides instructions is WHC-SD-RE-TP-024, Hanford Single Shell Tank Saltcake Cesium Removal Test Plan.

  9. A New Pumping-Probing Scheme for the Optically Pumped Cesium Beam Frequency Standard

    Institute of Scientific and Technical Information of China (English)

    陈景标; 朱程锦; 王凤芝; 杨东海

    2001-01-01

    A new pumping-probing scheme for the optically pumped cesium beam frequency standard has been experimentally tested in our laboratory. The stability of the optically pumped cesium beam frequency standard was measured by comparing its 10 MHz output with an HP5071A commercial cesium atomic clock. The result shows that the frequency stability for the 1 s and 30000s sample times are 1.2 × 10-11 and 3.7 × 10-13, respectively. It was proved that the new pumping scheme works well.

  10. Investigation of adsorption and wetting of 3He on cesium and cesiated glass

    International Nuclear Information System (INIS)

    Experiments have been carried out to investigate the binding of 3He on cesium substrates, using optical pumping to spin-polarize the atoms. The behavior of 3He on the walls at low temperature can be analyzed through the evolution of the nuclear magnetization of the sample. Preliminary results are presented, including: (1) adsorption studies of gaseous 3He on cesiated glass; (2) magnetic relaxation time of polarized liquid 3He on cesium and cesiated glass; (3) evidence for wetting of liquid 3He on cesium. 8 refs., 2 figs

  11. a Biokinetic Model for CESIUM-137 in the Fetus

    Science.gov (United States)

    Jones, Karen Lynn

    1995-01-01

    Previously, there was no method to determine the dose to the embryo, fetus, fetal organs or placenta from radionuclides within the embryo, fetus, or placenta. In the past, the dose to the fetus was assumed to be equivalent to the dose to the uterus. Watson estimated specific absorbed fractions from various maternal organs to the uterine contents which included the fetus, placenta, and amniotic fluid and Sikov estimated the absorbed dose to the embryo/fetus after assuming 1 uCi of radioactivity was made available to the maternal blood.^{1,2} However, this method did not allow for the calculation of a dose to individual fetal organs or the placenta. The radiation dose to the embryo or fetus from Cs-137 in the fetus and placenta due to a chronic ingestion by the mother was determined. The fraction of Cs-137 in the maternal plasma crossing the placenta to the fetal plasma was estimated. The absorbed dose from Cs-137 in each modelled fetal organ was estimated. Since there has been more research regarding potassium in the human body, and particularly in the pregnant woman, a biokinetic model for potassium was developed first and used as a basis and confirmation of the cesium model. Available pertinent information in physiology, embryology, biokinetics, and radiation dosimetry was utilized. Due to the rapid growth of the fetus and placenta, the pregnancy was divided into four gestational periods. The numerous physiological changes that occurred during pregnancy were considered and an appropriate biokinetic model was developed for each of the gestational periods. The amount of cesium in the placenta, embryo, and fetus was estimated for each period. The dose to the fetus from cesium deposited in the embryo or fetus and in the placenta was determined for each period using Medical Internal Radiation Dosimetry (MIRD) methodology. An uncertainty analysis was also performed to account for the variability of the parameters in the biokinetic model based on the experimental data

  12. Variations in soil texture and levels of 131I contamination on the 131I uptake and transfer in sunflower (Helianthus annus L.)

    International Nuclear Information System (INIS)

    The effects of soil texture and levels of 131I contamination on 131I uptake and soil to crop transfer factor (TF) in sunflower were studied in a pot experiment. The 131I uptake and tf were significant in root and in the sandy soil. With increase in the level of '131I contamination 131I uptake tended to increase, but the TF decreased. (author)

  13. Diffusion of water, cesium and neptunium in pores of rocks

    International Nuclear Information System (INIS)

    Teollisuuden Voima Oy (TVO) is investigating the feasibility to dispose of spent nuclear fuel within Finland. The present plan calls for the repository to be located in crystalline rock at a depth of several hundred meters. The safety assessment of the repository includes calculations of migration of waste nuclides. The flow of waste elements in groundwater will be retarded through sorption interaction with minerals and through diffusion into rock. Diffusion is the only mechanism retarding the migration of non-sorbing species and, it is expected to be the dominating retardation mechanism of many of the sorbing elements. In the investigation the simultaneous diffusion of tritiated water (HTO), cesium and neptunium in rocks of TVO investigation sites at Kivetty, Olkiluoto and Romuvaara were studied. (11 refs., 33 figs., 9 tabs.)

  14. Cesium-137 accident lessons in Goiania, Goias State, Brazil

    International Nuclear Information System (INIS)

    This document relates the experience obtained by several professionals which had an important role in the cesium-137 accident occurred in Goiania, Goias State, Brazil in September, 1987. It's divided into chapters, according to the action area - medical, nursing, social assistance, odontological and psychological. At first, some notions of radioprotection are explained, followed by the accident history and by the doctors and nurses action during the emergency phase and the medical, odontological, social and psychological assistance to the victims. The social assistance report shows some statistical data about the economic, occupational and social conditions of the accident victims. It is shown some information about the health institutions and the sanitary care in the ionizing radiation and about the occupational radiological protection in Goiania

  15. Coherence Properties of Nanofiber-Trapped Cesium Atoms

    Science.gov (United States)

    Reitz, D.; Sayrin, C.; Mitsch, R.; Schneeweiss, P.; Rauschenbeutel, A.

    2013-06-01

    We experimentally study the ground state coherence properties of cesium atoms in a nanofiber-based two-color dipole trap, localized ˜200nm away from the fiber surface. Using microwave radiation to coherently drive the clock transition, we record Ramsey fringes as well as spin echo signals and infer a reversible dephasing time of T2*=0.6ms and an irreversible dephasing time of T2'=3.7ms. By modeling the signals, we find that, for our experimental parameters, T2* and T2' are limited by the finite initial temperature of the atomic ensemble and the heating rate, respectively. Our results represent a fundamental step towards establishing nanofiber-based traps for cold atoms as a building block in an optical fiber quantum network.

  16. Norbadione A: synthetic approach and cesium complexation studies

    International Nuclear Information System (INIS)

    This work was dedicated to the study of the synthesis and complexation studies of norbadione A: a pigment originating from a mushroom. A synthetic approach, based on a double Suzuki-Miyaura coupling, was developed. This strategy was applied with high yields to the synthesis of various norbadione A analogues, as well as to the synthesis of simple pulvinic acids. Access to functionalized precursors of the molecule was also studied and the final coupling remains to be done. Besides, a speciation study based on electro-spray ionization mass spectrometry was conducted with norbadione A and one of the analogues. This study allowed the assessment of the cesium complexation abilities of each molecule. Structural data was also obtained and complexation constants were calculated. Finally, norbadione A and various synthetic products have been tested via high-throughput screening methods and strong antioxidant properties were observed. Other biological results are also reported. (author)

  17. Vector Cesium Magnetometer for the nEDM Experiment

    International Nuclear Information System (INIS)

    Full text: We use optical pumping combined with magnetic resonance in a Cesium vapor cell in order to measure the magnetic field. A Vector Cs Magnetometer uses multiple laser beams to follow the dynamics of the spin in 3D. The 3D signal is used to extract the Larmor frequency of the spins, and to extract the direction of the magnetic field through the path of the spins. The magnetometer was successfully tested in a proof of principle experiment. Its measured performance is ∼50 pT/Hz1/2 for the directions perpendicular to the magnetic field, and ∼500 fT/Hz1/2 for the direction parallel to the magnetic field. (author)

  18. Coherence properties of nanofiber-trapped cesium atoms

    CERN Document Server

    Reitz, D; Mitsch, R; Schneeweiss, P; Rauschenbeutel, A

    2013-01-01

    We experimentally study the ground state coherence properties of cesium atoms in a nanofiber-based two-color dipole trap, localized 200 nm away from the fiber surface. Using microwave radiation to coherently drive the clock transition, we record Ramsey fringes as well as spin echo signals and infer a reversible dephasing time $T_2^\\ast=0.6$ ms and an irreversible dephasing time $T_2^\\prime=3.7$ ms. By theoretically modelling the signals, we find that, for our experimental parameters, $T_2^\\ast$ and $T_2^\\prime$ are limited by the finite initial temperature of the atomic ensemble and the heating rate, respectively. Our results represent a fundamental step towards establishing nanofiber-based traps for cold atoms as a building block in an optical fiber quantum network.

  19. Quantitative analysis of cesium in synthetic lithium molten salts

    International Nuclear Information System (INIS)

    An analytical technique for fission products in lithium molten salts of spent PWR (Pressurized Water Reactor) fuels has been studied for the establishment of optimum chemical engineering process and the evaluation of process material balance in developing Direct Oxide Reduction Process with lithium metal. As part of the basic research, synthetic dissolver solutions of lithium chloride containing trace amounts of fission product elements (La, Ce, Pr, Nd, Sm, Eu, Gd, Y, Cs, Ru, Rh, Pd, Mo, Zr, Cd, Ba, Sr, Te and Se) was prepared and used in establishing the selective separation technique of cesium from lithium chloride matrix using cation exchange chromatography. Its recovery was measured by flame atomic absorption spectrometry and the reliability of this technique was evaluate

  20. Elastic scattering of sodium and cesium atoms at ultracold temperatures

    Institute of Scientific and Technical Information of China (English)

    Zhang Ji-Cai; Wang Ke-Dong; Liu Yu-Fang; Sun Jin-Feng

    2011-01-01

    The elastic scattering properties in a mixture of sodium and cesium atoms are investigated at cold and ultracold temperatures. Based on the accurate interatomic potential for the NaCs mixture,the interspecies s-wave scattering lengths,the effective ranges and the p-wave scattering lengths are calculated by the quantal method and the semiclassical method,respectively. The s-wave scattering lengths are 512.7ao for the singlet state and 33.4ao for the triplet state. In addition,the spin-change and elastic cross sections are also calculated,and the g-wave shape resonance is found in the total elastic cross sections.

  1. Vitrification of cesium-contaminated organic ion exchange resin

    Energy Technology Data Exchange (ETDEWEB)

    Sargent, T.N. Jr. [Clemson Univ., SC (United States)

    1994-08-01

    Vitrification has been declared by the Environmental Protection Agency (USEPA) as the Best Demonstrated Available Technology (BDAT) for the permanent disposal of high-level radioactive waste. Savannah River Site currently uses a sodium tetraphenylborate (NaTPB) precipitation process to remove Cs-137 from a wastewater solution created from the processing of nuclear fuel. This process has several disadvantages such as the formation of a benzene waste stream. It has been proposed to replace the precipitation process with an ion exchange process using a new resorcinol-formaldehyde resin developed by Savannah River Technical Center (SRTC). Preliminary tests, however, showed that problems such as crust formation and a reduced final glass wasteform exist when the resin is placed in the melter environment. The newly developed stirred melter could be capable of overcoming these problems. This research explored the operational feasibility of using the stirred tank melter to vitrify an organic ion exchange resin. Preliminary tests included crucible studies to determine the reducing potential of the resin and the extent of oxygen consuming reactions and oxygen transfer tests to approximate the extent of oxygen transfer into the molten glass using an impeller and a combination of the impeller and an external oxygen transfer system. These preliminary studies were used as a basis for the final test which was using the stirred tank melter to vitrify nonradioactive cesium loaded organic ion exchange resin. Results from this test included a cesium mass balance, a characterization of the semi-volatile organic compounds present in the off gas as products of incomplete combustion (PIC), a qualitative analysis of other volatile metals, and observations relating to the effect the resin had on the final redox state of the glass.

  2. Candlestick oven with a silica wick provides an intense collimated cesium atomic beam

    Science.gov (United States)

    Pailloux, A.; Alpettaz, T.; Lizon, E.

    2007-02-01

    This article shows that readily available glass and silica fibers and braids are suitable capillary structure for recirculating ovens, such as candlestick ovens, becoming then an alternative wick material to conventional metal based capillary structures. In order to study wettability and capillarity of metallic liquid cesium on borosilicate and silica microstructures, samples were selected, prepared, and tested experimentally. The contact angle of cesium on silica glass was roughly measured: θ =35°±10°. A commercially available silica braid was then introduced inside a candlestick oven to transfer the metallic liquid cesium from the cold reservoir to the hot emission point of the candlestick. A collimated cesium atomic beam of intensity of 2×1016at./ssr was obtained, stable and reproducible. Furthermore, this modified oven is easy to handle daily.

  3. Preparation, structure and application of a new ecomaterials cesium ion-sieve

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    A new ecomaterials cesium ion-sieve (Cs-IS), which has high selectivity to cesium and excellent acid resistance, is prepared with zirconyl molybdopyrophosphate as its matrix by specific chemical sieve-making means. Cs-IS has large exchange capacity ( 1.83mmol@g-1) and high distribution coefficient (4.09 x 104 mL@ L-1) in the medium of 3 mol@ L- 1 HNO3. In the static exchange with strongly acidic high-level radioactive liquid waste (HLLW) (3 mol@ L-1 HNO3), Cs-IS exhibits high exchange rate for cesium (above 96.53 % ) and large separation factor (greater than 958.41). These indicate the possible use of Cs-IS in cesium-137 selective removal and recovery from highly saline acidic HLLW system.

  4. Prussian blue caged in spongiform adsorbents using diatomite and carbon nanotubes for elimination of cesium.

    Science.gov (United States)

    Hu, Baiyang; Fugetsu, Bunshi; Yu, Hongwen; Abe, Yoshiteru

    2012-05-30

    We developed a spongiform adsorbent that contains Prussian blue, which showed a high capacity for eliminating cesium. An in situ synthesizing approach was used to synthesize Prussian blue inside diatomite cavities. Highly dispersed carbon nanotubes (CNTs) were used to form CNT networks that coated the diatomite to seal in the Prussian blue particles. These ternary (CNT/diatomite/Prussian-blue) composites were mixed with polyurethane (PU) prepolymers to produce a quaternary (PU/CNT/diatomite/Prussian-blue), spongiform adsorbent with an in situ foaming procedure. Prussian blue was permanently immobilized in the cell walls of the spongiform matrix and preferentially adsorbed cesium with a theoretical capacity of 167 mg/g cesium. Cesium was absorbed primarily by an ion-exchange mechanism, and the absorption was accomplished by self-uptake of radioactive water by the quaternary spongiform adsorbent. PMID:22464752

  5. Synthesis of novel calix[4]crown telomers and selective extraction of cesium ions

    Institute of Scientific and Technical Information of China (English)

    Hai Bing Li; Yuan Yin Chen; De Jun Xiong; Jun Yan Zhan; Cui Ping Han

    2007-01-01

    p-tert-Butylcalix[4]diazacrown-4 telomer, which contains hard and soft ion binding sites, was synthesized. It exhibited high selectivity toward cesium ions. The binding sites may complex alkali metal ions selectively.

  6. Biological effects of cesium-137 injected in beagle dogs of different ages

    Energy Technology Data Exchange (ETDEWEB)

    Nikula, K.J.; Muggenburg, B.A.; Griffith, W.C. [and others

    1995-12-01

    The toxicity of cesium-137 ({sup 137}Cs) in the Beagle dog was investigated at the Argonne National Laboratory (ANL) as part of a program to evaluate the biological effects of internally deposited radionuclides. The toxicity and health effects of {sup 137}Cs are important to understand because {sup 137}Cs is produced in large amounts in light-water nuclear reactors. Large quantities of cesium radioisotopes have entered the human food chain as a result of atmospheric nuclear weapons test, and additional cesium radioisotopes were released during the Chernobyl accident. Although the final analyses are not complete, three findings are significant: older dogs dies significantly earlier than juvenile and young adult dogs; greater occurrence of sarcomas in the cesium-137 injected dogs; the major nonneoplastic effect in dogs surviving beyond 52 d appears to be testicular atrophy.

  7. Total deposition of cesium-137 measured in Finland during the exercise `RESUME 95` in August 1995

    Energy Technology Data Exchange (ETDEWEB)

    Geer, L.E. De; Vintersved, I.; Arntsing, R. [National Defence Research Establisment, Nuclear Detection Group, Stockholm (Sweden)

    1997-12-31

    In the exercise called `RESUME 95` the Nuclear Detection Group from the National Defence Research Establishment in Stockholm participated with field gamma ray measurements combined with soil sampling and profile measurements. The results are presented in this report for the measurements of cesium-137. We considered the measurements of cesium-137 at the airfield the most important part of the in-situ exercise. Data was of course collected also for cesium-134 and natural radionuclides but time has not permitted a full analysis of these radionuclides. The methodology would, however, be the same as applied for cesium-137. Less attention was paid for area II and due to limited personnel resources the search exercise was not fully carried out. (au).

  8. Cold cesium molecules produced directly in a magneto-optical trap

    Institute of Scientific and Technical Information of China (English)

    Zhang Hong-Shan; Ji Zhong-Hua; Yuan Jin-Peng; Zhao Yan-Ting; Ma Jie; Wang Li-Rong; Xiao Lian-Tuan; Jia Suo-Tang

    2011-01-01

    We report on the observation of ultracold ground electric-state cesium molecules produced directly in a magnetooptical trap with a good signal-to-noise ratio.These molecules arise from the photoassociation of magneto-optical trap lasers and they are detected by resonantly enhanced multiphoton ionization technology.The production rate of ultracold cesium molecules is up to 4× 104 s-1.We measure the characteristic time of the ground electric-state cesium molecules generated in the experiment and investigate the Cs2+ molecular ion intensity as a function of the trapping laser intensity and the ionization pulse laser energy.We conclude that the production of cold cesium molecules may be enhanced by using appropriate experimental parameters,which is useful for future experiments involving the production and trapping of ultracold ground electric-state molecules.

  9. Cs2 ‘diffuse bands’ emission from superheated cesium vapor

    Science.gov (United States)

    Pichler, G.; Makdisi, Y.; Kokaj, J.; Thomas, N.; Mathew, J.; Beuc, R.

    2016-07-01

    Thermal emission from superheated cesium vapor was studied to very high temperatures from 700 °C to 1000 °C. This was performed in the vapor condition only and with no liquid cesium present in the all-sapphire cell. We observed a number of atomic and molecular spectral features simultaneously in emission and absorption, especially peculiar thermal emission of cesium dimer diffuse bands (2 3Πg → a 3∑u + transitions) around 710 nm coexisting with absorption bands around first resonance lines at 852 and 894 nm. We performed appropriate calculations of the diffuse band emission profiles and compared them with measured profiles. We also performed absorption measurements and compared observed diffuse band profiles with calculated ones. Possible applications of the observed phenomena will be discussed in terms of the solar energy conversion using dense cesium vapor.

  10. Fission of Multiply Charged Cesium and Potassium Clusters in Helium Droplets - Approaching the Rayleigh Limit

    CERN Document Server

    Renzler, Michael; Daxner, Matthias; Kranabetter, Lorenz; Kuhn, Martin; Scheier, Paul; Echt, Olof

    2016-01-01

    Electron ionization of helium droplets doped with cesium or potassium results in doubly and, for cesium, triply charged cluster ions. The smallest observable doubly charged clusters are $Cs_{9}^{2+}$ and $K_{11}^{2+}$; they are a factor two smaller than reported previously. The size of potassium dications approaches the Rayleigh limit nRay for which the fission barrier is calculated to vanish, i.e. their fissilities are close to 1. Cesium dications are even smaller than nRay, implying that their fissilities have been significantly overestimated. Triply charged cesium clusters as small as $Cs_{19}^{3+}$ are observed; they are a factor 2.6 smaller than previously reported. Mechanisms that may be responsible for enhanced formation of clusters with high fissilities are discussed.

  11. Metabolism of I-131-meta-iodobenzylguanidine (MIBG) in humans

    International Nuclear Information System (INIS)

    I-131-MIBG is used to image and treat human pheochrmocytoma. As part of a pharmacodynamic study, the authors have evaluated its excretion and metabolism in 8 pheochromocytoma patients undergoing MIBG therapy. Following diagnostic doses (0.42-0.53 mCi) of I-131-MIBG given prior to therapy, 40-55% of the administered radioactivity appears in the urine within 24 h with 70-90% recoverable within 4 days. HPLC was used to identify potential metabolites following therapeutic doses (130-213 mCi) of I-131-NIBG. Aliquots of daily urine samples were prepared for HPLC analysis by passage through C-18 Sep-pak cartridges. A reverse-phase HPLC system (μBondapak C-18; 0.2 M ammonium phosphate/THF, 80/20) with both ultraviolet (254 nm) and radioactive (Flo-one detector, solid scintillant cell) detection was used. Radioactive metabolites were identified by co-chromatography with authentic compounds at elution solvent pH's of 4.6 and 7.0. Unaltered I-131-MIBG was the primary radioactive urinary component in all 8 patients studied, representing 74-90% of the total recovered. Two ''major'' metabolites were identified: I-131-iodide and I-131-m-iodohippuric acid, representing, respectively, 2-6% and 2-16% of the total urinary radioactivity. Of 4 additional ''minor'' metabolites (< 2% of total urinary radioactivity) detected, 2 have been identified: I-131-4-hydroxy-MIBG and I-131-m-iodobenzoic acid. The 4-5 day metabolism profiles varied from patient to patient but did not change in 2 patients given 2 therapy doses 4 months apart. No obvious correlation was observed between the presence of metabolites and the location of the tumors or the plasma or urinary catecholamine levels. I-131-MIBC is a rapidly excreted, relatively stable radiopharmaceutical agent

  12. Nursing of patients with hyperthyroidism treated by using iodine-131

    International Nuclear Information System (INIS)

    Hyperthyroidism was a common endocrine disease, its clinic treatment mainly include anti thyroid drug treatment, surgical operation and iodine-131 therapy. The latter have unique superiority, which was adapted by clinic doctors. The nursing method was distinguished from that of others because the principle of iodine-131 therapy was different from other therapy in course of the treatment of hyperthyroidism. Combining the nursing experiences with related documents, this article was about to sum up briefly the nursing and matters needing attention in course of treatment of iodine-131 in patients with hyperthyroidism

  13. Radiation shielding of 131I therapeutic ward in department

    International Nuclear Information System (INIS)

    Objective: To rebuild an 131I therapeutic ward of the department of nuclear medicine in the hospital, and design the radiation shielding to make the radiation safety achieve the national standards. Methods: According to the protection demands of national relating standards, the design of the ward was based on the basic principles and methods of radiation shielding of 131I, and combined the distribution of radioactive sources, rooms and people. Results: The design parameters and radioprotection data of the rebuilt ward were obtained and the radiation shielding was safe by monitoring. Conclusion: The design of the 131I therapeutic ward achieved the anticipated target that the radiation safety could be controlled. (authors)

  14. Fabrication and performance of fl y ash granule filter for trapping gaseous cesium

    Directory of Open Access Journals (Sweden)

    Park Jang Jin

    2015-09-01

    Full Text Available Although a disk-type fly ash filter has shown a good performance in trapping gaseous cesium, it has difficulty in charging filters into a filter container and discharging waste filters containing radioactive cesium from a container by remote action. To solve the difficulty of the disk-type fly ash filter, five types of granule filters, including a ball type, tube type, and sponge-structure type have been made. Among them, the best filter type was chosen through simple crucible tests. The five types of granule filters packed into containers were loaded into five alumina crucibles of 50 cc. Five grams of CsNO3 was used as a gaseous cesium source. They were then placed in a muffle furnace and heated to 900°C and maintained for 2 hours. After the experiment, the weights of the cesium trapped filters were measured. Among the five types of granule filters, the sponge-structure type granule filter was the best, which has the highest trapping capacity of cesium. Its capacity is 0.42 g-Cs/g-filter. The chosen sponge-structure type granule filters and disk-type filters have been tested using a two-zone tube furnace. Cs volatilization and Cs trapping zones were maintained at 900 and 1000°C, respectively. Sixteen grams of CsNO3 was used as a gaseous cesium source. The cesium trapping profile of the sponge-structure type granule filters was almost similar to that of the disk-type fly ash filters. For both cases, cesium was successfully trapped within the third filter.

  15. 131I-chTNT-mediated radioimmunotherapy for non-uptaking 131I pulmonary metastases from differentiated thyroid carcinoma

    International Nuclear Information System (INIS)

    In this paper, the safety and efficacy of 131I-labeled mouse/human chimeric monoclonal antibody (131I-chTNT)-mediated radioimmunotherapy are evaluated because the patients have non-uptaking 131I pulmonary metastases from differentiated thyroid carcinoma (DTC). The 16 patients were injected intravenously by 29.6±3.7 MBq·kg-1 using 131I-chTNT. The chest computer tomography was performed before treatment, as well as 28 and 70 days after treatment. Responses and safety were assessed during the treatment. The results show that the 131I-chTNT infusion was well tolerated with the 12.5% complete response, 18.8% partial response, 25.0% progressive disease, and the 43.8% stable disease, indicating that most treatment-related adverse effects are mild transient and reversible. The 131I-chTNT is promising for patients with non-uptaking the 131I pulmonary metastases from DTC. (authors)

  16. Enhanced electronic injection in organic light-emitting diodes by incorporating silver nanoclusters and cesium carbonate

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Ying-Chung; Gao, Chia-Yuan [Department of Electrical Engineering, National Sun Yat-Sen University, Kaohsiung, Taiwan (China); Chen, Kan-Lin [Department of Electronic Engineering, Fortune Institute of Technology, Kaohsiung, Taiwan (China); Sze, Po-Wen [Department of Electro-Optical Science and Engineering, Kao Yuan University, Kaohsiung, Taiwan (China); Huang, Chien-Jung, E-mail: chien@nuk.edu.tw [Department of Applied Physics, National University of Kaohsiung, Kaohsiung, Taiwan (China)

    2015-10-01

    Highlights: • The localized electric field around SNCs is enhanced. • When the cesium carbonate/silver nanoclusters/cesium carbonate electron-injection structure replaces the cesium carbonate electron-injection structure, higher electron-injection ability is obtained. • The structure for efficient electron injection is critical to characteristics of the device. - Abstract: The influence of the cesium carbonate/silver nanoclusters/cesium carbonate electron-injection structure (CSC-EIS) on the performance of organic light-emitting diodes is investigated in this study. The silver nanoclusters (SNCs) are introduced between the electron-injection layers by means of thermal evaporation. When the CSC-EIS replaces the cesium carbonate electron-injection structure, higher electron-injection ability is obtained because the electron-injection barrier between the cathode and the electron-transport layer is remarkably reduced from 1.2 to 0 eV. In addition, surface plasmon resonance effect will cause the enhanced localized electric field around the SNCs, resulting that electron-injection ability is further enhanced from the cathode to the emitting layer.

  17. Measurement of cesium emissions during the vitrification of simulated high level radioactive waste

    International Nuclear Information System (INIS)

    In the Defense Waste Processing Facility at the Savannah River Site, it is desired to eliminate a startup test that would involve adding small amounts of radioactive cesium-137 to simulated high-level waste. In order to eliminate this test, a reliable method for measuring non-radioactive cesium in the offgas system from the glass melter is required. From a pilot scale melter system, offgas particulate samples were taken on filter paper media and analyzed by Inductively Coupled Plasma-Mass Spectrometry (ICP-MS). The ICPMS method proved to be sufficiently sensitive to measure cesium quantities as low as 0.135 μg, with the sensitivity being limited by the background cesium present in the filter paper. Typical particulate loadings ranged from 800 μg of cesium. This sensitivity allowed determination of cesium decontamination factors for four of the five major components of the offgas system. The decontamination factors measured experimentally compared favorably with the process design basis values

  18. Modeling Ion-Exchange Processing With Spherical Resins For Cesium Removal

    Energy Technology Data Exchange (ETDEWEB)

    Hang, T.; Nash, C. A.; Aleman, S. E.

    2012-09-19

    The spherical Resorcinol-Formaldehyde and hypothetical spherical SuperLig(r) 644 ion-exchange resins are evaluated for cesium removal from radioactive waste solutions. Modeling results show that spherical SuperLig(r) 644 reduces column cycling by 50% for high-potassium solutions. Spherical Resorcinol Formaldehyde performs equally well for the lowest-potassium wastes. Less cycling reduces nitric acid usage during resin elution and sodium addition during resin regeneration, therefore, significantly decreasing life-cycle operational costs. A model assessment of the mechanism behind ''cesium bleed'' is also conducted. When a resin bed is eluted, a relatively small amount of cesium remains within resin particles. Cesium can bleed into otherwise decontaminated product in the next loading cycle. The bleed mechanism is shown to be fully isotherm-controlled vs. mass transfer controlled. Knowledge of residual post-elution cesium level and resin isotherm can be utilized to predict rate of cesium bleed in a mostly non-loaded column. Overall, this work demonstrates the versatility of the ion-exchange modeling to study the effects of resin characteristics on processing cycles, rates, and cold chemical consumption. This evaluation justifies further development of a spherical form of the SL644 resin.

  19. Prussian blue caged in spongiform adsorbents using diatomite and carbon nanotubes for elimination of cesium

    International Nuclear Information System (INIS)

    Highlights: ► Prussian blue was sealed in cavities of diatomite using carbon nanotubes. ► The caged Prussian blue after being permanently immobilized in polyurethane spongy showed a 167 mg/g capability for absorbing cesium. ► Cesium elimination was accomplished by simply adding the Prussian-blue based spongiform adsorbent to radioactive water. - Abstract: We developed a spongiform adsorbent that contains Prussian blue, which showed a high capacity for eliminating cesium. An in situ synthesizing approach was used to synthesize Prussian blue inside diatomite cavities. Highly dispersed carbon nanotubes (CNTs) were used to form CNT networks that coated the diatomite to seal in the Prussian blue particles. These ternary (CNT/diatomite/Prussian-blue) composites were mixed with polyurethane (PU) prepolymers to produce a quaternary (PU/CNT/diatomite/Prussian-blue), spongiform adsorbent with an in situ foaming procedure. Prussian blue was permanently immobilized in the cell walls of the spongiform matrix and preferentially adsorbed cesium with a theoretical capacity of 167 mg/g cesium. Cesium was absorbed primarily by an ion-exchange mechanism, and the absorption was accomplished by self-uptake of radioactive water by the quaternary spongiform adsorbent.

  20. Prussian blue caged in spongiform adsorbents using diatomite and carbon nanotubes for elimination of cesium

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Baiyang [Graduate School of Environmental Science, Hokkaido University, Sapporo 060-0810 (Japan); Fugetsu, Bunshi, E-mail: hu@ees.hokudai.ac.jp [Graduate School of Environmental Science, Hokkaido University, Sapporo 060-0810 (Japan); Yu, Hongwen [Graduate School of Environmental Science, Hokkaido University, Sapporo 060-0810 (Japan); Abe, Yoshiteru [Kyoei Engineering Corporation, Niigata 959-1961 (Japan)

    2012-05-30

    Highlights: Black-Right-Pointing-Pointer Prussian blue was sealed in cavities of diatomite using carbon nanotubes. Black-Right-Pointing-Pointer The caged Prussian blue after being permanently immobilized in polyurethane spongy showed a 167 mg/g capability for absorbing cesium. Black-Right-Pointing-Pointer Cesium elimination was accomplished by simply adding the Prussian-blue based spongiform adsorbent to radioactive water. - Abstract: We developed a spongiform adsorbent that contains Prussian blue, which showed a high capacity for eliminating cesium. An in situ synthesizing approach was used to synthesize Prussian blue inside diatomite cavities. Highly dispersed carbon nanotubes (CNTs) were used to form CNT networks that coated the diatomite to seal in the Prussian blue particles. These ternary (CNT/diatomite/Prussian-blue) composites were mixed with polyurethane (PU) prepolymers to produce a quaternary (PU/CNT/diatomite/Prussian-blue), spongiform adsorbent with an in situ foaming procedure. Prussian blue was permanently immobilized in the cell walls of the spongiform matrix and preferentially adsorbed cesium with a theoretical capacity of 167 mg/g cesium. Cesium was absorbed primarily by an ion-exchange mechanism, and the absorption was accomplished by self-uptake of radioactive water by the quaternary spongiform adsorbent.

  1. Analysis of pelvic 131I uptake after 131I whole body scan in patients with thyroid cancer

    International Nuclear Information System (INIS)

    Objective: To analyze and explore the possible mechanism for pelvic 131I uptake after 131I post treatment whole body scan (Rx-WBS)in patients with differentiated thyroid cancer. Methods: (1) Data were retrospectively reviewed from 168 female patients with differentiated thyroid cancer (everyone has a Rx-WBS). (2) 46 patients were accepted by analyzing the characteristics of Rx-WBS and combing with some inclusion criteria,and then followed up. Results: Among the 46 patients (46 positions accumulated 131I) with significant pelvic 131I uptake, 6 patients had two reasons leading to pelvic 131I uptake, and 2 patients had no specific reason. Among the 50 reasons for pelvic 131I uptake, 41 reasons related with uterus, 3 reasons related to rectum, 5 related to bladder and 1 related to ovarian chocolate cyst. Among the 41 reasons related to uterus, by combining the examinations of SPECT/CT, ultrasound, CT and the follow-up results, 18 were uterine leiomyomas, 9 were intrauterine devices, 2 were endometrial thickening, 3 were uterine cavity effusion, 7 were menstrual periods, 1 were uterine adenomyosis, 1 were gestational sac. Conclusions: (1) In the Rx-WBS of female, the significant pelvic 131I uptake is generally caused by uterus, but not bladder. And it usually means gynecological disease, especially uterine leiomyomas when excluding physiological factors. (2) It is generally easy to differentiate bladder from rectum because they have different characteristic features of the pelvic 131I uptake. (3) SPECT/CT plays a very important role in locating 131I uptake in uterus. (authors)

  2. The effects of K+ growth conditions on the accumulation of cesium by the bacterium Thermus sp. TibetanG6

    Institute of Scientific and Technical Information of China (English)

    WANG; Hailei; KONG; Fanjing; ZHENG; Mianping

    2006-01-01

    The accumulation of cesium by the bacterium Thermus sp. TibetanG6 was examined under different K+ growth conditions. The effects of external pH and Na+ on the accumulation of cesium were also studied, and the mechanism involved was discussed. K+ regimes played an important role in the accumulation of cesium by the strain TibetanG6. The quantity of cesium accumulated (24 h) was much higher in K+-deficient regime than that in K+-sufficient regime. The pH and Na+ had different effects on the accumulation of cesium in the two K+ regimes. IR spectra analyses indicated that the biosorption is a process of homeostasis with cesium initially accumulated on the cell wall.

  3. Monitoring of radionuclides in the environment. Part. 4. Factors influencing depth profiles of radioactive cesium in soils

    International Nuclear Information System (INIS)

    In order to evaluate the vertical migration behavior of radioactive cesium, which contaminated by the Fukushima Dai-ichi NPP accident, the distribution of radioactive cesium in different type of soils, e.g., bare ground, grass land, conifer forest floor were measured on October 2011, 2012, 2013, in Abiko, Chiba, Japan. Even three years after the deposition, most of radioactive cesium were deposited in the depths of within 5 cm at anywhere in this area. Depth profiles of radioactive cesium in soil was significantly correlated with organic matter content in soils (r=0.82; p<0.0001), whereas the factors such as potassium ion and ammonium ion in soil, stable cesium content, and clay mineral content were not correlated clearly. This indicates that the vertical migration rate of radioactive cesium is very slow and it would be influenced by organic matter in soil, not just clay. (author)

  4. Prototype development of filter monitor for 131I processing plant

    International Nuclear Information System (INIS)

    Iodine-131 (131I) is used extensively in nuclear medicine because of its short half-life and useful beta emission. Isotope Production and Applications Division (IP and AD) of BARC produces 131I in its processing plant. The charcoal filters that are capable of extracting high levels of radioactive iodine and particulates in the suction flow are installed in the plant. The radioactive iodine is fully removed and deposited onto activated charcoal impregnated with potassium iodide. These charcoal filters get saturated over a period of use and need to be replaced with fresh ones. A 5-channel Filter monitor for online measurement of radiation level of trapped 131I on the charcoal filter is being developed by IP and AD, BARC. The unavailability of this type of instrument motivated to undertake this development. Current paper deals with a prototype filter monitor developed with single detector. Some results prove the functionality of the system. (author)

  5. Resveratrol Sensitizes Selectively Thyroid Cancer Cell to 131-Iodine Toxicity

    Directory of Open Access Journals (Sweden)

    Seyed Jalal Hosseinimehr

    2014-01-01

    Full Text Available Background. In this study, the radiosensitizing effect of resveratrol as a natural product was investigated on cell toxicity induced by 131I in thyroid cancer cell. Methods. Human thyroid cancer cell and human nonmalignant fibroblast cell (HFFF2 were treated with 131I and/or resveratrol at different concentrations for 48 h. The cell proliferation was measured by determination of the percent of the survival cells using 3-(4,5-dimethylthiazol-2-yl-2,5-diphenyltetrazolium bromide (MTT assay. Results. Findings of this study show that resveratrol enhanced the cell death induced by 131I on thyroid cancer cell. Also, resveratrol exhibited a protective effect on normal cells against 131I toxicity. Conclusion. This result indicates a promising effect of resveratrol on improvement of cellular toxicity during iodine therapy.

  6. Guidelines on the management of patients treated with iodine-131

    International Nuclear Information System (INIS)

    The purpose of these guidelines is to assist health care institutions establish protocols for the management of patients treated with iodine-131. These guidelines are written primarily for the use of Na131I in the treatment of benign and malignant thyroid disease. The principles have some application for the use of complex 131I-labelled radiopharmaceuticals in that the treated patient will become a temporary radiation source and since contamination with body fluids of treated patients must be guarded against. The document outlines radiation protection and logistical concerns associated with the management of 131I patients before, during and after therapy. These concerns include the safety of health care personnel, visitors, and any other persons who are at risk; and protection of the environment. (L.L.) 23 refs., 2 tabs

  7. Additional effective dose by patients undergoing NAI-131 capsules therapy

    Energy Technology Data Exchange (ETDEWEB)

    Orlic, M.; Jovanovic, M.; Spasic Jokic, V.; Cuknic, O.; Ilic, Z.; Vranjes Djuric, S. [VINCA - Institute of Nuclear Sciences, Belgrade, Serbia and Montenegro (Yugoslavia)

    2006-07-01

    Capsules or solutions containing Na{sup 131}I are indicated for the therapy of some thyroid carcinomas such as functioning metastatic papillary or follicular carcinoma of the thyroid; and for the treatment of hyperthyroidism (diffuse toxic goiter and single or multiple toxic nodular goiter). The recommended dosage ranges of Na{sup 131}I capsules or solution for the therapy of the average patient (70 kg) are: (3.7-5.55) GBq for ablation of normal thyroid tissue; (3.7-7.4) GBq for subsequent treatments; a (148-370) MBq for hyperthyroidism. The purpose of this paper is to calculate effective dose as a result of iodine-131 capsules remaining in stomach before absorption starts. This result can determine the disadvantage of capsule versus solution containing sodium iodine-131 (Na{sup 131}I) in radionuclide therapy application from radiation protection point of view. The Monte Carlo code MCNP4b was used to model transport of gamma and beta particles emitted by radionuclide {sup 131}I treated as a point source at the bottom of stomach. Absorbed energy per unit transformation in stomach and surrounding organs has been calculated. (authors)

  8. Engineered Materials for Cesium and Strontium Storage Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Sean M. McDeavitt

    2010-04-14

    Closing the nuclear fuel cycle requires reprocessing spent fuel to recover the long-lived components that still have useful energy content while immobilizing the remnant waste fission products in stable forms. At the genesis of this project, next generation spent fuel reprocessing methods were being developed as part of the U.S. Department of Energy's Advanced Fuel Cycle Initiative. One of these processes was focused on solvent extraction schemes to isolate cesium (Cs) and strontium (Sr) from spent nuclear fuel. Isolating these isotopes for short-term decay storage eases the design requirements for long-term repository disposal; a significant amount of the radiation and decay heat in fission product waste comes from Cs-137 and Sr-90. For the purposes of this project, the Fission Product Extraction (FPEX) process is being considered to be the baseline extraction method. The objective of this project was to evaluate the nature and behavior of candidate materials for cesium and strontium immobilization; this will include assessments with minor additions of yttrium, barium, and rubidium in these materials. More specifically, the proposed research achieved the following objectives (as stated in the original proposal): (1) Synthesize simulated storage ceramics for Cs and Sr using an existing labscale steam reformer at Purdue University. The simulated storage materials will include aluminosilicates, zirconates and other stable ceramics with the potential for high Cs and Sr loading. (2) Characterize the immobilization performance, phase structure, thermal properties and stability of the simulated storage ceramics. The ceramic products will be stable oxide powders and will be characterized to quantify their leach resistance, phase structure, and thermophysical properties. The research progressed in two stages. First, a steam reforming process was used to generate candidate Cs/Sr storage materials for characterization. This portion of the research was carried out at

  9. Engineered Materials for Cesium and Strontium Storage. Final Technical Report

    International Nuclear Information System (INIS)

    Closing the nuclear fuel cycle requires reprocessing spent fuel to recover the long-lived components that still have useful energy content while immobilizing the remnant waste fission products in stable forms. At the genesis of this project, next generation spent fuel reprocessing methods were being developed as part of the U.S. Department of Energy's Advanced Fuel Cycle Initiative. One of these processes was focused on solvent extraction schemes to isolate cesium (Cs) and strontium (Sr) from spent nuclear fuel. Isolating these isotopes for short-term decay storage eases the design requirements for long-term repository disposal; a significant amount of the radiation and decay heat in fission product waste comes from Cs-137 and Sr-90. For the purposes of this project, the Fission Product Extraction (FPEX) process is being considered to be the baseline extraction method. The objective of this project was to evaluate the nature and behavior of candidate materials for cesium and strontium immobilization; this will include assessments with minor additions of yttrium, barium, and rubidium in these materials. More specifically, the proposed research achieved the following objectives (as stated in the original proposal): (1) Synthesize simulated storage ceramics for Cs and Sr using an existing labscale steam reformer at Purdue University. The simulated storage materials will include aluminosilicates, zirconates and other stable ceramics with the potential for high Cs and Sr loading. (2) Characterize the immobilization performance, phase structure, thermal properties and stability of the simulated storage ceramics. The ceramic products will be stable oxide powders and will be characterized to quantify their leach resistance, phase structure, and thermophysical properties. The research progressed in two stages. First, a steam reforming process was used to generate candidate Cs/Sr storage materials for characterization. This portion of the research was carried out at Purdue

  10. Estimation of ingestion dose due to I-131 in the initial month by using food-monitoring data after the Fukushima nuclear disaster in Japan

    International Nuclear Information System (INIS)

    The committed equivalent dose to the thyroid caused by I-131 and the effective dose caused by I-131, Cs-134 and Cs-137 due to ingestion immediately after the accidental releases following the Fukushima nuclear disaster in March 2011 were estimated retrospectively by using measured food data. A food monitoring dataset provided by the Ministry of Health, Labour and Welfare (MHLW) up to April 18, 2011 (N=1,752) was used for this study. Information on food consumption by 99 food categories was made available by using the original data of the Japanese National Food Consumption Survey, which was conducted in 2009 (N=9,942). Food concentration every 4 days and food consumption in each food category was randomly picked up (N=100,000). The levels of radioactive iodine and cesium were summed for one month and then converted to equivalent doses to the thyroid and effective doses. These doses in the first month after the Fukushima nuclear power plant accident were evaluated by using the food monitoring dataset provided by the MHLW. Assuming that food was randomly extracted from monitored food samples and food restrictions were fully implemented, the 90%tile of the equivalent doses to the thyroid and the effective doses in 1- to 6-year-old children were estimated to be around 1 mSv and 0.07 mSv, respectively. Several different methods should be considered to reduce limitations of this estimation. (author)

  11. Preparation and characterization of cesium-137 aluminosilicate pellets for radioactive source applications

    International Nuclear Information System (INIS)

    Twenty-seven fully loaded 137Cs aluminosilicate pellets were fabricated in a hot cell by the vacuum hot pressing of a cesium carbonate/montmorillonite clay mixture at 15000C and 570 psig. Four pellets were selected for characterization studies which included calorimetric measurements, metallography, scanning electron microscope and electron backscattering (SEM-BSE), electron microprobe, x-ray diffraction, and cesium ion leachability measurements. Each test pellet contained 437 to 450 curies of 137Cs as determined by calorimetric measurements. Metallographic examinations revealed a two-phase system: a primary, granular, gray matrix phase containing large and small pores and small pore agglomerations, and a secondary fused phase interspersed throughout the gray matrix. SEM-BSE analyses showed that cesium and silicon were uniformly distributed throughout both phases of the pellet. This indicated that the cesium-silicon-clay reaction went to completion. Aluminum homogeneity was unconfirmed due to the high background noise associated with the inherent radioactivity of the test specimens. X-ray diffraction analyses of both radioactive and non-radioactive aluminosilicate pellets confirmed the crystal lattice structure to be pollucite. Cesium ion quasistatic leachability measurements determined the leach rates of fully loaded 137Cs sectioned pollucite pellets to date to be 4.61 to 34.4 x 10-10 kg m-2s-1, while static leach tests performed on unsectioned fully loaded pellets showed the leach rates of the cesium ion to date to be 2.25 to 3.41 x 10-12 kg m-2s-1. The cesium ion diffusion coefficients through the pollucite pellet were calculated using Fick's first and second laws of diffusion. The diffusion coefficients calculated for three tracer level 137Cs aluminosilicate pellets were 1.29 x 10-16m2s-1, 6.88 x 10-17m2s-1, and 1.35 x 10-17m2s-1, respectively

  12. The crystal structures of potassium and cesium trivanadates

    Science.gov (United States)

    Evans, H.T.; Block, S.

    1966-01-01

    Potassium and cesium trivanadates are monoclinic and isomorphous, space group P21/m, with the following dimensions (Z = 2): KV3O8, a = 7.640 A, b = 8.380 A, c = 4.979 A, ??= 96?? 57???; CsV3O8, a = 8.176 A, b = 8.519 A, c = 4.988 A, ?? = 95?? 32???. The crystal structure of KV3O8 has been determined from hk0, 0kl, and h0l Weissenberg data with an R factor of 0.15. The structure of CsV3O8 has been refined with 1273 hkl Weissenberg data to an R factor of 0.089. The structures consist of corrugated sheets based on a linkage of distorted VO6, octahedra. Two of the vanadium atoms lie in double, square-pyramid groups V2O8, which are linked through opposite basal corners into chains along the b axis. The chains are joined laterally along the c axis into sheets by the third vanadium atom in VO groups, also forming part of a square-pyramid coordination. Various aspects of these structures are compared with other known oxovanadate structures.

  13. ATLAS tile calorimeter cesium calibration control and analysis software

    International Nuclear Information System (INIS)

    An online control system to calibrate and monitor ATLAS Barrel hadronic calorimeter (TileCal) with a movable radioactive source, driven by liquid flow, is described. To read out and control the system an online software has been developed, using ATLAS TDAQ components like DVS (Diagnostic and Verification System) to verify the hardware before running, IS (Information Server) for data and status exchange between networked computers, and other components like DDC (DCS to DAQ Connection), to connect to PVSS-based slow control systems of Tile Calorimeter, high voltage and low voltage. A system of scripting facilities, based on Python language, is used to handle all the calibration and monitoring processes from hardware perspective to final data storage, including various abnormal situations. A QT based graphical user interface to display the status of the calibration system during the cesium source scan is described. The software for analysis of the detector response, using online data, is discussed. Performance of the system and first experience from the ATLAS pit are presented

  14. Cesium sorption and desorption behavior of clay minerals

    International Nuclear Information System (INIS)

    Cesium sorption and desorption of clay minerals (montmorillonite, beidellite, nontronite, weathered biotite, rectorite and illite) were investigated by consecutive sorption-desorption (CSD) experiments. In batch sorption experiment, two solutions with different Cs concentration 10-3 and 10-7 mol/L) were used. In batch desorption experiments, Cs sorbed samples in sorption experiments were treated 5 times with 1 mol/L ammonium acetate solution. In the case of CSD experiments using 10-3 mol/L Cs solution, the exchangeable cations (Na, Ca, and K) in the clay samples affected to the sorption ratio of Cs, and this effect depended on the type of clay mineral. The desorption ratios of untreated, Na-exchanged and Ca-exchanged weathered biotite ranged from 23 to 33%, while that of other samples was over 80%. In the case of CSD experiments using 10-7 mol/L Cs solution, the sorption ratio of montmorillonite was smaller than that of the other clay samples. In desorption experiments, more than 10-9 mol sorbed Cs remained in 1.0 g of the sample after 5 extraction times. These results indicate that all examined clay samples are able to strongly adsorb Cs with a capacity of more than 10-9 mol/g. (author)

  15. Broadband Vibrational Cooling of Cold Cesium Molecules: Theory and Experiments

    Institute of Scientific and Technical Information of China (English)

    D. Sofikitis; A. Fioretti; S. Weber; M. Viteau; A. Chotia; R. Horchani; M. Allegrini; B. Chatel; D. Comparat; P. Pillet

    2009-01-01

    The use of a broadband, frequency shaped femtosecond laser on translationally cold cesium molecules has recently demonstrated to be a very efficient method of cooling also the vibrational degree of freedom. A sample of cold molecules, initially distributed over several vibrational levels, has thus been transfered into a single selected vibrational level of the singlet X1∑g ground electronic state. Our method is based on repeated optical pumping by laser light with a spectrum broad enough to excite all populated vibrational levels but limited in its frequency bandwidth with a spatial light modulator. In such a way we are able to eliminate transitions from the selected level, in which molecules accumulate. In this paper we briefly report the main experimental results and then address, in a detailed way by computer simulations, the perspectives for a "complete" cooling of the molecules, including also the rotational degree of freedom. Since the pumping process strongly depends on the rclative shape of the ground and excited potential curves, ro-vibrational cooling through different excited states is theoretically compared.

  16. Evaluation of a cesium adsorbent grafted with ammonium 12-molybdophosphate

    Science.gov (United States)

    Shibata, Takuya; Seko, Noriaki; Amada, Haruyo; Kasai, Noboru; Saiki, Seiichi; Hoshina, Hiroyuki; Ueki, Yuji

    2016-02-01

    A fibrous cesium (Cs) adsorbent was developed using radiation-induced graft polymerization with a cross-linked structure containing a highly stable adsorption ligand. The ligand, ammonium 12-molybdophosphate (AMP), was successfully introduced onto the fibrous polyethylene trunk material. The resulting Cs adsorbent contained 36% nonwoven fabric polyethylene (NFPE), 1% AMP, 2% triallyl isocyanurate (TAIC) and 61% glycidyl methacrylate (GMA). The adsorbent's Cs adsorption capacity was evaluated using batch and column tests. It was determined that the adsorbent could be used in a wide pH range. The amount of desorbed molybdenum, which can be used as an estimate for AMP stability on the Cs adsorbent, was minimized at the standard drinking water pH range of 5.8-8.6. Based from the inspection on the adherence of these results to the requirements set forth by the Food Sanitation Act by a third party organization, it can be concluded that the developed Cs adsorbent can be safely utilized for drinking water.

  17. Ion exchange performance of commercial crystalline silicotitanates for cesium removal

    Energy Technology Data Exchange (ETDEWEB)

    Braun, R.; Dangieri, T.J.; Fennelly, D.J. [and others

    1996-03-01

    A new class of inorganic ion exchangers called crystalline silicotitanates (CST), invented by researchers at Sandia National Laboratories and Texas A&M University, has been commercialized in a joint Sandia-UOP effort. The original developmental materials exhibited high selectivity for the ion exchange of cesium, strontium, and several other radionuclides from highly alkaline solutions containing molar concentrations of Na{sup +}. The materials also showed excellent chemical and radiation stability. Together, the high selectivity and stability of the CSTs made them excellent candidates for treatment of solutions such as the Hanford tank supernates and other DOE radwastes. Sandia National Laboratories and UOP have teamed under a Cooperative Research and Development Agreement (CRADA) to develop CSTs in the powdered form and in an engineered form suitable for column ion exchange use. A continuous-flow, column ion exchange process is expected to be used to remove Cs and other radionuclides from the Hanford supernatant. The powder material invented by the Sandia and Texas A&M team consists of submicron-size particles. It is not designed for column ion exchange but may be used in other applications.

  18. Hanford Isotope Project strategic business analysis Cesium-137 (Cs-137)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-10-01

    The purpose of this business analysis is to address the beneficial reuse of Cesium 137 (Cs-137) in order to utilize a valuable national asset and possibly save millions of tax dollars. Food irradiation is the front runner application along with other uses. This business analysis supports the objectives of the Department of Energy National Isotope Strategy distributed in August 1994 which describes the DOE plans for the production and distribution of isotope products and services. As part of the Department`s mission as stated in that document. ``The Department of Energy will also continue to produce and distribute other radioisotopes and enriched stable isotopes for medical diagnostics and therapeutics, industrial, agricultural, and other useful applications on a businesslike basis. This is consistent with the goals and objectives of the National Performance Review. The Department will endeavor to look at opportunities for private sector to co-fund or invest in new ventures. Also, the Department will seek to divest from ventures that can more profitably or reliably be operated by the private sector.``

  19. Hanford Isotope Project strategic business analysis Cesium-137 (Cs-137)

    International Nuclear Information System (INIS)

    The purpose of this business analysis is to address the beneficial reuse of Cesium 137 (Cs-137) in order to utilize a valuable national asset and possibly save millions of tax dollars. Food irradiation is the front runner application along with other uses. This business analysis supports the objectives of the Department of Energy National Isotope Strategy distributed in August 1994 which describes the DOE plans for the production and distribution of isotope products and services. As part of the Department's mission as stated in that document. ''The Department of Energy will also continue to produce and distribute other radioisotopes and enriched stable isotopes for medical diagnostics and therapeutics, industrial, agricultural, and other useful applications on a businesslike basis. This is consistent with the goals and objectives of the National Performance Review. The Department will endeavor to look at opportunities for private sector to co-fund or invest in new ventures. Also, the Department will seek to divest from ventures that can more profitably or reliably be operated by the private sector.''

  20. Interventions in 131I-MIBG treatment of neuroendocrine tumours

    International Nuclear Information System (INIS)

    Full text: Specific targeting of neuroendocrine tumours for therapy may be achieved either via the metabolic route (MIBG), via receptor binding (peptides) or via the immunological route (antibodies). Any malignant neural crest tumour, showing sufficient uptake and retention of 131I-meta-odobenzylguanidine (MIBG) on a diagnostic tracer study is a candidate for therapy using this agent. The principle indications for 131I-MIBG therapy are malignant pheochromocytoma and paraganglioma, neuroblastoma stage III and IV, medullary thyroid carcinoma and symptomatic, metastatic carcinoid tumors. At an EANM Radionuclide Therapy Committee workshop on 131IMIBG therapy in 1999 the results of treatment in 534 patients with neural crest tumours were gathered, showing cumulative objective response rates of 51% for malignant pheochromocytoma, 48% for paraganglioma, 51% for neuroblastoma, 23% for medullary thyroid carcinoma and 8% for carcinoid tumors. Moreover, symptomatic palliation occurred in more than 60% of the patients. These results compare favorably with the best reported results of combination chemotherapy. An active uptake-1 mechanism at the cell membrane and neurosecretory storage granules in the cytoplasm of neural crest tumours are responsible for the uptake and retention of 131I-MIBG, respectively, resulting in high tumour/nontumour ratio's. Many drugs are known or may be expected to interfere with (i.e. have a negatively effect on) the uptake and/or retention of 131I-MIBG by the tumour cell. In contrast, there are also factors which may influence either the uptake/retention of 131I-MIBG or the results of therapy in a positive way. Possible interventions: 1. Use of other labels, for example 125I-MIBG, 211At-MABG and 76Br-MBBG, which, in view of their ultrashort pathway, may have a role in the treatment of micrometastases and bone marrow infiltration, particularly as the results of 131I-MIBG therapy under these circumstances are poor. 2. By increasing the specific

  1. Misinterpretation on the risk of radioactive cesium contained in the disaster wastes

    International Nuclear Information System (INIS)

    Osaka Prefectural Government accepted the disaster wastes contained radioactive cesium after investigation them during one year. I explained the process and discussed about the risk management by people and the self-government body. The environmental pollution by radioactive cesium and Act on Special Measures concerning the Handling of Pollution by Radioactive Materials, the progress of treatment of debris, the concentration of radioactive cesium in debris, the acceptance conditions of debris contained small amount of radioactive cesium, evaluation of effects of radioactive materials in debris on the environment, and citizen's opinion of Osaka prefecture are described. The important investigation area of radioactive contamination on the basis of Act on Special Measures concerning the Handling of Pollution by Radioactive Materials, total amount of waste from Fukushima nuclear accident and debris in Miyagi, Iwate and Fukushima prefecture, the concentration of radioactive cesium in debris in Rikuzentakata and Miyako city as of September, 2011, and cumulative number of citizen's opinion to Osaka are illustrated. (S.Y.)

  2. Local mat-forming cyanobacteria effectively facilitate decontamination of radioactive cesium in rice fields

    International Nuclear Information System (INIS)

    The most effective and widespread method to decontaminate radioactive cesium from the Fukushima Daiichi Nuclear Power Plant Disaster was peeling topsoil. But the method had problems, such as large amounts of discarded soil and large-scale work. In nature, cyanobacteria formed biomats on the ground surface and facilitated peeling topsoil when the biomats dried. The cyanobacteria-facilitating peeling decontamination method utilized these cyanobacterial properties. Cyanobacteria are located all over Japan and 'local' cyanobacteria could be used for decontamination without introducing new species. Utilizing cyanobacteria could decrease the amount of discarded soil to about 30% and downsize the execution-scale to individual locations. Cyanobacterial biomats were easily cultivated, especially in rice fields, by maintaining wet conditions and exposure to 100 - 83% solar radiation. Shading by a thin net was helpful in maintaining an environment suitable for cyanobacteria. Nowadays, to prevent uptake of radioactive cesium into rice, K+ is usually added to fertilizer in rice fields. The K+ fertilization in rice fields might also enhance cyanobacterial capture of radioactive cesium, because high concentrations of K+ enhanced cyanobacterial uptake of Cs+. Cyanobacteria could also mitigate the risk of radioactive cesium moving away from a decontaminating rice field. Therefore, the cyanobacteria-facilitating peeling decontamination method was proposed as an easy and safe 'D.I.Y.' method for both farmers and the environment. Besides, plowing rice fields with water before peeling improved the efficiency of this method, because plowing increased the radioactive cesium concentration in the topsoil. (author)

  3. Development program for magnetically assisted chemical separation: Evaluation of cesium removal from Hanford tank supernatant

    International Nuclear Information System (INIS)

    Magnetic particles (MAG*SEPSM) coated with various absorbents were evaluated for the separation and recovery of low concentrations of cesium from nuclear waste solutions. The MAG*SEPSM particles were coated with (1) clinoptilolite, (2) transylvanian volcanic tuff, (3) resorcinol formaldehyde, and (4) crystalline silico-titanate, and then were contacted with a Hanford supernatant simulant. Particles coated with the crystalline silico-titanate were identified by Bradtec as having the highest capacity for cesium removal under the conditions tested (variation of pH, ionic strength, cesium concentration, and absorbent/solution ratio). The MAG*SEPSM particles coated with resorcinol formaldehyde had high distribution ratios values and could also be used to remove cesium from Hanford supernant simulant. Gamma irradiation studies were performed on the MAG*SEPSM particles with a gamma dose equivalent to 100 cycles of use. This irradiation decreased the loading capacity and distribution ratios for the particles by greater than 75%. The particles demonstrated high sensitivity to radiolytic damage due to the degradation of the polymeric regions. These results were supported by optical microscopy measurements. Overall, use of magnetic particles for cesium separation under nuclear waste conditions was found to be marginally effective

  4. Efficiency of fly ash belite cement and zeolite matrices for immobilizing cesium.

    Science.gov (United States)

    Goñi, S; Guerrero, A; Lorenzo, M P

    2006-10-11

    The efficiency of innovative matrices for immobilizing cesium is presented in this work. The matrix formulation included the use of fly ash belite cement (FABC-2-W) and gismondine-type Na-P1 zeolite, both of which are synthesized from fly ash of coal combustion. The efficiency for immobilizing cesium is evaluated from the leaching test ANSI/ANS 16.1-1986 at the temperature of 40 degrees C, from which the apparent diffusion coefficient of cesium is obtained. Matrices with 100% of FABC-2-W are used as a reference. The integrity of matrices is evaluated by porosity and pore-size distribution from mercury intrusion porosimetry, X-ray diffraction and nitrogen adsorption analyses. Both matrices can be classified as good solidify systems for cesium, specially the FABC-2-W/zeolite matrix in which the replacement of 50% of belite cement by the gismondine-type Na-P1 zeolite caused a decrease of two orders of magnitude of cesium mean Effective Diffusion Coefficient (D(e)) (2.8e-09 cm(2)/s versus 2.2e-07 cm(2)/s, for FABC-2-W/zeolite and FABC-2-W matrices, respectively). PMID:16759800

  5. Preparation of Modified Kaolin Filler with Cesium and Its Application in Security Paper

    Directory of Open Access Journals (Sweden)

    Houssni El-Saied

    2013-01-01

    Full Text Available In this study, cesium was added intentionally during paper manufacture for protecting the papers against forgery and counterfeiting by sorbing cesium ions (Cs+ on kaolin, used as special filler in papermaking. The sorption of cesium from aqueous solution by kaolin was studied as a function of pH, shaking time, cesium initial concentration, and mass of kaolin using batch technique. The results showed that a solution containing 10 mg/L Cs+ and 250 mg of kaolin at pH 6 can be used to modify the kaolin. Paper handsheets were prepared containing various percentages of the modified kaolin. The mechanical and optical properties of paper handsheets were studied. The prepared paper handsheets were irradiated by gamma irradiation using different doses. Fourier transform infrared (FTIR spectroscopy was used to study the effect of kaolin modification by cesium and gamma irradiation on paper handsheets properties. The results indicated that modified kaolin enhanced the mechanical and optical properties of paper handsheets. Electron spin resonance (ESR spectroscopy and laser-induced breakdown spectroscopy (LIBS were also used. They provided rapid, sensitive and nondestructive techniques in differentiating between different questioned documents. This study presents a new concept in manufacturing security papers and anticounterfeiting applications.

  6. Cesium-137 in soil texture fractions and its impact on Cesium-137 soil-to-plant transfer

    International Nuclear Information System (INIS)

    Field studies at two sites contaminated by the Chernobyl fallout showed 137Cesium (Cs) soil-to-plant transfer factors in wheat, rye and potato. Transfer values ranged from 0.0017 (potato tuber) to 0.07 (wheat straw). Generally transfer coefficients in cereal grains and potato tubers were significantly below the values of the shoots. A comparison of the two sites led to the conclusion that for all plants investigated 137Cs transfer factors were higher in Lower Austria (Calcic Chernozem) than in Upper Austria (Eutric Cambisol). The specific activities of the texture fractions of the two soil types increased from sand to silt and clay. In the Calcic Chernozem the ratio of the 137Cs activity in the silt fraction to the total activity in the soil was considerably higher than in the Eutric Cambisol. At the same time extractability of 137Cs from the silt fraction of the latter soil was clearly lower. Both results mainly were attributed to the differences between the soils according to the organic matter content of the silt fractions, the Calcic Chernozem being seven times higher. Therefore, the differences in the 137Cs-soil-to-plant transfer can be attributed partly to these soil characteristics. (authors)

  7. 131I treatment for brain metastases from differentiated thyroid carcinoma

    Institute of Scientific and Technical Information of China (English)

    YU Yong-Li; LU Han-Kui; ZHU Rei-Sen; MA Ji-Xiao

    2004-01-01

    To assess the clinical value of treatment with 131I for brain metastases from differentiated thyroid cancer (DTC), we have observed 8 cases of brain metastases from DTC who received follow-up after 131I therapy (2male, 6 female, aged 12~65 years). The results of 131I therapy were evaluated with clinical presentation, imaging scan and survival analysis. The main results are as follows. (1) All cases had been survival for 2~35 years in follow-up. (2)A space-occupying lesion in right cerebellum was reduced after taking 20.65 GBq and disappeared after 23.61 GBq,demonstrated by computed tomography. (3) The sequences and doses of 131I therapy were clearly decreased for the cases with total thyroidectomy in comparison with those with semithyroidectomy (p<0.01). (4) The brain metastases with lung and/or bone metastasis from DTC were 75% (6/8) and it was difficult to cure these metastases at the same time. It is concluded that the postoperative treatment of 131I for brain metastases from DTC after undergoing thyroidectomy may improve clinical symptoms and life quality, reduce lesions, and prolong survival.

  8. Thyroid cancer from occupational exposures to iodine-131

    International Nuclear Information System (INIS)

    Studies of external irradiation, primarily of children, suggest that the thyroid gland is one of the most radiosensitive sites for carcinogenesis. However, it has generally been thought that 131I confers much less risk (per rad) than external radiation because of its low dose-rate. A review of the epidemiologic literature indicates that age at irradiation is also an important variable in defining thyroid cancer risk, with a lesser risk at older ages. The available human studies are reasonably consistent in affirming that risks following 131I are small. However, the data on 131I exposure are too sparse, particularly for childhood exposure, to determine how much of the observed diminution in risk is due to older ages at exposure and how much is attributable to the characteristics of 131I exposure per se, such as low dose-rate. Since most of the existing studies have inadequacies in design, dose levels, dosimetry or number of subjects, additional studies are needed before the risk assessment of 131I at lower dose levels in adult workers can be regarded as definitive

  9. Familial phaeochromocytoma: Successful treatment with sup 131 I-MIBG

    Energy Technology Data Exchange (ETDEWEB)

    Goncalves, E.; Ninane, J.; Wese, F.X.; Leonet, J.; Piret, L.; Cornu, G.; De Meyer, R. (Cliniques Universitaires Saint Luc, Brussels (Belgium))

    1990-01-01

    We report the case of a family in which the mother died of hypertensive encephalopathy following the relapse of a phaeochromocytoma. Two of her children are still alive. Both children had malignant phaeochromocytomas that have been treated by surgery and {sup 131}I-MIBG. The first child presented with phaeochromocytoma of the right suprarenal gland at the age of 7 years. Surgery was performed. At the age of 14 years, he developed a tumour of the left suprarenal gland and two pulmonary metastases demonstrated by {sup 131}I-MIBG. The three tumours were removed, but new lesions occurred. The boy then was treated with 200 mCi (7,400 MBq) of 131I-MIBG given twice, and is now free of disease more than 2 years after treatment. His sister presented at the age of 12 years with phaeochromocytoma of the left suprarenal gland, the only lesion recognized by {sup 131}I-MIBG. The tumour was removed, but 5 months later, she developed phaeochromocytoma in the right suprarenal gland. She was treated with 200 mCi (7,400 MBq) of {sup 131}I-MIBG and surgery was performed 6 months later. Histology of the suprarenal gland could not demonstrate the persistence of phaeochromocytoma cells. The child is now free of disease more than 2 years after treatment.

  10. Structural basis for a Munc13-1 homodimer to Munc13-1/RIM heterodimer switch.

    Directory of Open Access Journals (Sweden)

    Jun Lu

    2006-07-01

    Full Text Available C(2 domains are well characterized as Ca(2+/phospholipid-binding modules, but little is known about how they mediate protein-protein interactions. In neurons, a Munc13-1 C(2A-domain/RIM zinc-finger domain (ZF heterodimer couples synaptic vesicle priming to presynaptic plasticity. We now show that the Munc13-1 C(2A domain homodimerizes, and that homodimerization competes with Munc13-1/RIM heterodimerization. X-ray diffraction studies guided by nuclear magnetic resonance (NMR experiments reveal the crystal structures of the Munc13-1 C(2A-domain homodimer and the Munc13-1 C(2A-domain/RIM ZF heterodimer at 1.44 A and 1.78 A resolution, respectively. The C(2A domain adopts a beta-sandwich structure with a four-stranded concave side that mediates homodimerization, leading to the formation of an eight-stranded beta-barrel. In contrast, heterodimerization involves the bottom tip of the C(2A-domain beta-sandwich and a C-terminal alpha-helical extension, which wrap around the RIM ZF domain. Our results describe the structural basis for a Munc13-1 homodimer-Munc13-1/RIM heterodimer switch that may be crucial for vesicle priming and presynaptic plasticity, uncovering at the same time an unexpected versatility of C(2 domains as protein-protein interaction modules, and illustrating the power of combining NMR spectroscopy and X-ray crystallography to study protein complexes.

  11. In vivo biological evaluation of {sup 131}I radiolabeled-paclitaxel glucuronide ({sup 131}I-PAC-G)

    Energy Technology Data Exchange (ETDEWEB)

    Aslan, O.; Biber Muftuler, F.Z.; Yurt Kilcar, A.; Ichedef, C.; Unak, P. [Ege Univ., Izmir (Turkey). Dept. of Nuclear Applications

    2012-07-01

    Paclitaxel (PAC) is a natural occurring diterpene alkoloid originally isolated from the bark of Taxus Brevifolia. It is one of the most important antitumor agents for clinical treatment of ovarian, breast non-small cell lung and prostate cancers. It is known that these types of cancer cells have high {beta}-glucuronidase enzyme which can catalyze the hydrolysis of glucuronides. This is why the synthesis compounds which undergo glucuronidation come into question in the imaging and therapy of these cancer cells. The aim of current study is conjugation of glucuronic acid (G) to the starting substance PAC, labeling with {sup 131}I and to perform its in vivo biological evaluation. Glucuronic acid derived paclitaxel compound [paclitaxel-glucuronide (PAC-G)] was labeled with {sup 131}I using iodogen method. According to thin layer radio chromatography (TLRC) method, the radiochemical yield of {sup 131}I-PAC-G was 84.30 {+-} 7.40% (n=10). The biodistribution of {sup 131}I-PAC-G in healthy female and male Wistar Albino rats has been investigated. Imaging studies on male Balb-C mice were performed by using the Kodak FX PRO in vivo Imaging System. The range of the breast/blood, breast/muscle; ovary/blood, ovary/muscle ratios is approximately between 1.29 and 11.34 in 240 min, and between 0.71 and 8.24 in 240 min for female rats. The prostate/blood and prostate/muscle ratio is between 1.94 and 6.95 in 30 min for male rats. All these experimental studies indicate that {sup 131}I-PAC-G may potentially be used in breast, ovary and prostate tissues as an imaging agent. Also it is thought that {sup 131}I-PAC-G bears a therapy potential because of the {sup 131}I radionuclide and can be improved with further investigations. (orig.)

  12. Sympathetic cooling in a rubidium cesium mixture: Production of ultracold cesium atoms; Sympathetisches Kuehlen in einer Rubidium-Caesium-Mischung: Erzeugung ultrakalter Caesiumatome

    Energy Technology Data Exchange (ETDEWEB)

    Haas, M.

    2007-07-01

    This thesis presents experiments for the production of ultracold rubidium cesium mixture in a magnetic trap. The long-termed aim of the experiment is the study of the interaction of few cesium atoms with a Bose-Einstein condensate of rubidium atoms. Especially by controlled variation of the cesium atom number the transition in the description of the interaction by concepts of the one-particle physics to the description by concepts of the many-particle physics shall be studied. The rubidium atoms are trapped in a magneto-optical trap (MOT) and from there reloaded into a magnetic trap. In this the rubidium atoms are stored in the state vertical stroke f=2,m{sub f}=2 right angle of the electronic ground state and evaporatively cooled by means of microwave-induced transitions into the state vertical stroke f=1,m{sub f}=1] (microwave cooling). The cesium atoms are also trppaed in a MOT and into the same magnetic trap reloaded, in which they are stored in the state vertical stroke f=4,m{sub f}=4 right angle of the electronic ground state together with rubidium. Because of the different hyperfine splitting only rubidium is evaporatively cooled, while cesium is cooled jointly sympathetically - i.e. by theramal contact via elastic collisions with rubidium atoms. The first two chapters contain a description of interatomic interactions in ultracold gases as well as a short summary of theoretical concepts in the description of Bose-Einstein condensates. The chapters 3 and 4 contain a short presentation of the methods applied in the experiment for the production of ultracold gases as well as the experimental arrangement; especially in the framework of this thesis a new coil system has been designed, which offers in view of future experiments additionally optical access for an optical trap. Additionally the fourth chapter contains an extensive description of the experimental cycle, which is applied in order to store rubidium and cesium atoms together into the magnetic trap. The

  13. Comparison of organic and inorganic ion exchange materials for removal of cesium and strontium from tank waste

    Energy Technology Data Exchange (ETDEWEB)

    Brown, G. [Pacific Northwest National Lab., Richland, WA (United States)

    1996-10-01

    This work is part of an ESP task to develop high-capacity, selective, solid extractants for cesium, strontium, and technetium from nuclear wastes. Pacific Northwest National Laboratory (PNNL) staff are investigating novel ion exchangers for use in nuclear waste remediation (groundwater, high-level waste (HLW), and low-level waste (LLW)). Waste components targeted for remediation include cesium, strontium, and technetium.

  14. Synthesis labeling and biological studies of 16-131I

    International Nuclear Information System (INIS)

    The increasing interest in obtaining radiopharmaceuticals for metabolic imaging of heart muscle led us to prepare 16-IODINE HEXADECANOIC ACID by tosilation of the corresponding hydroxy acid, following iodination with NaI and finally, introducing radioiodine (Na131I) by isotopic exchange reaction. The reaction products were identified by determination of melting point, elementary and spectroscopic analysis such as infra-red absortion and magnetic nuclear resonance. The radiopharmaceutical after radiochemical and other specific control procedures for injetable such as sterility and apyrogenicity, was firstly utilized in dogs: preferencial uptake by the heart, as well as by the liver was confirmed. Then, studies in patients with or without heart diseases were performed. The biodistribution of 16-131I-HEXADECANOIC ACID was carried out in Wistar rats. The scintigraphic images in animals and in humans demonstrated that 16-131-HEXADECANOIC ACID is suitable for studying viable areas as well as energetic exchange of heart muscle. (author)

  15. Behavior of ruthenium, cesium and antimony during simulated HLLW vitrification

    International Nuclear Information System (INIS)

    The behavior of ruthenium, cesium, and antimony during the vitrification of simulated high-level radioactive liquid wastes (HLLW) in a liquid fed melter was studied on a laboratory scale and on a semi-pilot scale. In the laboratory melter of a 2.5 kg capacity, a series of tests with the simulate traced with 103Ru, 134Cs and 124Sb, has shown that the Ru and Cs losses to the melter effluent are generally higher than 10% whereas the antimony losses remain lower than 0.4%. A wet purification system comprising in series, a dust scrubber, a condenser, an ejector venturi and an NOx washing column retains most of the activity present in the off-gas so that the release fractions for Ru at the absolute filter inlet ranges between 5.10-3 to 5.10-5% of the Ru fed, for Cs the corresponding release fraction ranges between 3.10-3 to 10-4% and for Sb the release fraction ranges between 1.7 10-4 to 1.7 10-5%. The same experiments were performed at a throughput of 1 to 2 1 h-1 of simulated solution in the semi-pilot scale unit RUFUS. The RUFUS unit comprises a glass melter with a 50 kg molten glass capacity and the wet purification train comprises in series a dust scrubber, a condenser, an ejector venturi and an NOx washing column. The tracer tests were restricted to 103Ru and 134Cs since the laboratory tests had shown that the antimony losses were very low. The results of the tests are presented

  16. Cesium and Strontium Specific Exchangers for Nuclear Waste Effluent Remediation

    International Nuclear Information System (INIS)

    During the past 50 years, nuclear defense activities have produced large quantities of nuclear waste that now require safe and permanent disposal. The general procedure to be implemented involves the removal of cesium and strontium from the waste solutions for disposal in permanently vitrified media. This requires highly selective sorbents or ion exchangers. Further, at the high radiation doses present in the solution, organic exchangers or sequestrants are likely to decompose over time. Inorganic ion exchangers are resistant to radiation damage and can exhibit remarkably high selectivities. We have synthesized three families of tunnel-type ion exchangers. The crystal structures of these compounds as well as their protonated phases, coupled with ion exchange titrations, were determined and this information was used to develop an understanding of their ion exchange behavior. The ion exchange selectivities of these phases could be regulated by isomorphous replacement of the framework metals by larger or smaller radius metals. In the realm of layered compounds, we prepared alumina, silica, and zirconia pillared clays and sodium micas. The pillared clays yielded very high Kd values for Cs+ and were very effective in removing Cs+ from groundwaters. The sodium micas also had a high affinity for Cs+ but an even greater attraction for S42+. They also possess the property of trapping these ions permanently as the layers slowly decrease their interlayer distance as loading occurs. Sodium nonatitanate exhibited extremely high Kd values for Sr2+ in alkaline tank wastes and should be considered for removal of Sr2+ in such cases. For tank wastes containing complexing agents, we have found that adding Ca2+ to the solution releases the complexed Sr2+ which may then be removed with the CST exchanger

  17. Immobilisation and solidification of cesium on 11 A calcium silicate hydroxy hydrate column

    International Nuclear Information System (INIS)

    Calcium silicate hydrate closely resembling silicate mineral 11 A tobermorite has been synthesised by hydrothermal treatment of lime and silica at 175 degC. The synthetic mineral exhibits selectivity for Cs+ in the presence of strong solutions of alkali and alkaline earth cations, viz, Na+, K+, Mg2+, Ca2+, Sr2+, etc. The Al-substituted form of this mineral effectively separates cesium ion when used as an exchanger in column of size 35x5 mm (hxr). It is possible to remove 98.65±0.5%Cs+ from a mixed solution of cesium and sodium (0.0001N Cs+ + 0.5N Na+). Column separation of cesium from simulated intermediate level waste solution shows that from the first run ∼ 76% Cs+ can be immobilised on a small column, 18x10mm (hxr), having 2.0 g of exchanger. (author)

  18. Studies of cesium and strontium migration in unconsolidated Canadian geological materials

    International Nuclear Information System (INIS)

    Distribution coefficients (Ksub(d)) were measured for cesium and strontium in 16 samples of Canadian unconsolidated geological materials. The samples were collected to cover a wide range of grain size, clay-mineral composition, cation exchange capacity and carbonate mineral content. Distribution coefficients ranged between 102 and 2.0 x 104 ml/g for cesium and between 2.5 and 102 ml/g for strontium, indicating that most unconsolidated geological materials have a substantial ability to retard the migration of cesium, while strontium could generally be expected to be somewhat more mobile. The measured K values were not significantly correlated with the measured soil properties, but appeared to be significantly affected by the background concentration of stable isotopes of the respective radionuclides

  19. The effects of using Cesium-137 teletherapy sources as a radiological weapon (dirty bomb)

    CERN Document Server

    Liolios, Theodore

    2009-01-01

    While radioactive sources used in medical diagnosis do not pose a great security risk due to their low level of radioactivity, therapeutic sources are extremely radioactive and can presumably be used as a radiological weapon. Cobalt-60 and Cesium-137 sources are the most common ones used in radiotherapy with over 10,000 of such sources currently in use worldwide, especially in the developing world, which cannot afford modern accelerators. The present study uses computer simulations to investigate the effects of using Cesium-137 sources from teletherapy devices as a radiological weapon. Assuming a worst-case terrorist attack scenario, we estimate the ensuing cancer mortality, land contamination, evacuation area, as well as the relevant evacuation, decontamination, and health costs in the framework of the linear risk model. The results indicate that an attack with a Cesium-137 dirty bomb in a large metropolitan city (especially one that would involve several teletherapy sources) although would not cause any sta...

  20. Phosphate ceramic solidification and stabilization of cesium-containing crystalline silicotitanate resins.

    Energy Technology Data Exchange (ETDEWEB)

    Langton, C. A.

    1999-05-11

    This paper reports on the fabrication and testing of magnesium potassium phosphate (MKP)-bonded cesium-loaded crystalline silicotitanate (CST) resins. Typical waste loading of CST resins in the final waste forms was 50 wt.%. Physical and chemical characterization of the MKP materials has shown them to be physically, chemically, and mineralogically stable. Long-term durability studies (using the AN 16.1 standard test) showed a leachability index of {approx}18 for cesium in the phosphate matrix when exposed to deionized water under ambient and elevated temperatures. Leaching of cesium was somewhat higher than in glass waste forms as per PCT and MCC-1 tests. MKP-based final waste forms showed no significant weight changes after exposure to aqueous media for {approx}90 days, indicating the highly insoluble nature of the phosphate matrix. In addition, durability of the CST-MKP waste forms was further established by freeze-thaw cycling tests.

  1. Determining Reactor Flux from Xenon-136 and Cesium-135 in Spent Fuel

    CERN Document Server

    Hayes, A C

    2012-01-01

    The ability to infer the reactor flux from spent fuel or seized fissile material would enhance the tools of nuclear forensics and nuclear nonproliferation significantly. We show that reactor flux can be inferred from the ratios of xenon-136 to xenon-134 and cesium-135 to cesium-137. If the average flux of a reactor is known, the flux inferred from measurements of spent fuel could help determine whether that spent fuel was loaded as a blanket or close to the mid-plane of the reactor. The cesium ratio also provides information on reactor shutdowns during the irradiation of fuel, which could prove valuable for identifying the reactor in question through comparisons with satellite reactor heat monitoring data. We derive analytic expressions for these correlations and compare them to experimental data and to detailed reactor burn simulations. The enrichment of the original uranium fuel affects the correlations by up to 3 percent, but only at high flux.

  2. Reduction of cesium levels in the diet through management of food

    International Nuclear Information System (INIS)

    Several processes influence the radionuclide concentration of food products during processing: dilution, losses, concentration. Boiling of leaf vegetables yields a decontamination effect of up to 80% in the case of radioiodine. Peeling of potato tubers results in a reduction of the cesium concentration of 30%. The cesium and strontium concentration of flour is a factor of two lower as compared to the corresponding cereal grain due to the milling process. Significant discrimination occurs during the milk processing. The skimmed milk is significantly richer in cesium, iodine and especially in strontium than the cream. It follows that butter is depleted in its radionuclide contents as compared to other milk produce. Strontium is concentrated in the casein. Pressurized cooking in combination with salting or a treatment with acetic acid results in an Cs-activity loss of beef, veal and lamb meat of 50 to 90%. (Author) 3 figs., 7 tabs., 13 refs

  3. Continuous Separation of Cesium Based on NiHCF/PTCF Electrode by Electrochemically Switched Ion Exchange

    Institute of Scientific and Technical Information of China (English)

    孙斌; 郝晓刚; 王忠德; 张忠林; 刘世斌; 官国清

    2012-01-01

    Nickel hexacyanoferrate (NiHCF) film was synthesized on porous three-dimensional carbon felt (PTCF) substrate by repetitious batch chemical depositions, and the NiHCF/PTCF electrode was used as electrochemically switched ion exchange (ESIX) electrode in a packed bed for continuous separation for cesium ions. The morphologies of the prepared electrodes were characterized by scanning electron microscopy and the effects of solution concentration on the ion-exchange capacity of the electrodes were investigated by cyclic voltammetry technique. Cycling stability and long-term storage stability of NiHCF/PTCF electrodes were also studied. The NiHCF/PTCF electrodes with excellent ion-exchange ability were used to assemble a diaphragm-isolated ESIX reactor for cesium separation. Continuous separation of cesium and regeneration of NiHCF/PTCF electrode based on the diaphragm-isolated reactor were performed in a laboratory-scale two-electrode system.

  4. Small-Column Cesium Ion Exchange Elution Testing of Spherical Resorcinol-Formaldehyde

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Garrett N.; Russell, Renee L.; Peterson, Reid A.

    2011-10-21

    This report summarizes the work performed to evaluate multiple, cesium loading, and elution cycles for small columns containing SRF resin using a simple, high-level waste (HLW) simulant. Cesium ion exchange loading and elution curves were generated for a nominal 5 M Na, 2.4E-05 M Cs, 0.115 M Al loading solution traced with 134Cs followed by elution with variable HNO3 (0.02, 0.07, 0.15, 0.23, and 0.28 M) containing variable CsNO3 (5.0E-09, 5.0E-08, and 5.0E-07 M) and traced with 137Cs. The ion exchange system consisted of a pump, tubing, process solutions, and a single, small ({approx}15.7 mL) bed of SRF resin with a water-jacketed column for temperature-control. The columns were loaded with approximately 250 bed volumes (BVs) of feed solution at 45 C and at 1.5 to 12 BV per hour (0.15 to 1.2 cm/min). The columns were then eluted with 29+ BVs of HNO3 processed at 25 C and at 1.4 BV/h. The two independent tracers allowed analysis of the on-column cesium interaction between the loading and elution solutions. The objective of these tests was to improve the correlation between the spent resin cesium content and cesium leached out of the resin in subsequent loading cycles (cesium leakage) to help establish acid strength and purity requirements.

  5. Cesium removal from high-pH, high-salt wastwater using crystalline silicotitanate sorbent

    Energy Technology Data Exchange (ETDEWEB)

    Walker, J.F. Jr.; Taylor, P.A.; Lee, D.D.

    1997-11-01

    Treatment and disposal options for Department of Energy (DOE) underground storage tank waste at Hanford, Savannah River, and Oak Ridge National Laboratory (ORNL) are limited by high gamma radiation fields that are produced by high concentrations of cesium in the waste. Treatment methods are needed to remove the cesium from the liquid waste and thus concentrate the cesium into high-activity, remote-handled waste forms. The treated liquids could then be processed and disposed of by more cost-effective means with less radiation exposure to workers. A full-scale demonstration of one cesium removal technology is currently being conducted at ORNL. This demonstration utilizes a modular, mobile ion-exchange system and existing facilities for the off-gas system, secondary containment, and utilities. The ion-exchange material, crystalline silicotitanate (CST), was chosen on the basis of its effectiveness in laboratory tests. The CST, which was developed through a Cooperative Research and Development Agreement between DOE and private industry, has several advantages over current organic ion-exchange technologies. These advantages include (1) the ability to remove cesium in the presence of high concentrations of potassium, (2) a high affinity for cesium in both alkaline and acidic conditions, (3) physical stability over wide alkaline and acidic ranges, and (4) the elimination of large volumes of secondary waste required for regeneration of organic ion exchangers. Approximately 100,000 L of wastewater will be processed during the demonstration. The wastewater being processed has a high salt content, about 4 M NaNO{sub 3}, and a pH of 12 to 13. This paper discusses the results of the full-scale demonstration and compares these results with data from the laboratory tests.

  6. False-positive I-131 uptake in meningioma

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Shin Young; Seo, Ji Hyoung; Bae, Jin Ho; Hwang, Jeong Hyun; Ahn, Byeong Cheol; Lee, Jae Tae; Lee, Kyu Bo [School of Medicine, Kyungpook National Univ., Daegu (Korea, Republic of)

    2004-06-01

    We experienced a case with meningioma showing false positive I-131 uptake. A 55-years old female patient underwent high dose (150 mCi) radioactive iodine therapy to ablate remnant tissue after total thyroidectomy for papillary thyroid cancer. In addition to intense tracer uptake in thyroid bed, there was mild but focal abnormal uptake in left frontal lobe of the brain on post-therapy I-131 whole body scan. Subsequent brain MR imaging showed single mass lesion in left frontal lobe and the mass was resected under the impression of brain metastasis of thyroid carcinoma. Pathologic report confirmed meningioma from the surgical specimen.

  7. Synthesis and labelling of 19-iodocholesterol 131I

    International Nuclear Information System (INIS)

    Considering the increasing interest in obtaining agents for vizualization of the adrenal gland with radioisotopic techniques, 19-iodocholesterol was prepared by means of chemical synthesis and radioiodine (131I) introduced by isotopic exchange reaction. The reaction product was identified by determination of the melting point and elementary spectroscopic analysis (infra-red absorption and magnetic nuclear ressonance). Radiochemical analysis of the labelled compound was performed by means of then-layer cromatography in silica-gel. In order to confirm its capacity of concentration in the adrenal gland, the distribution of 19-iodocholesterol 131I, after intravenous injection, was tested in rats. (Author)

  8. The importance of localisation within 131J-retention measurements

    International Nuclear Information System (INIS)

    A widely used method to investigate thyroid gland carcinomas, but also disorders of the thyroid gland is the measurement of the 131J-retention behaviour using a high-sensitivity whole-body counter (HWBC). Normally just the retention of oral administered Radioiodine is controlled. However, it is possible to visualize the distribution of 131J (using a modified profilescantechnique) beside the retention in the human body and this provides much better information on human metabolism as will be demonstrated in the following

  9. Fast timing measurement in neutron rich 131,132I

    International Nuclear Information System (INIS)

    The recent experimental and theoretical investigations carried out in this direction also indicate the importance of the lifetime measurements in these nuclei. Such measurements in 131,132I nuclei was attempted using Mirror Symmetric Centroid Difference (MSCD) technique, giving rise to the limits on the level lifetimes. In the present work, the lifetime measurements have been carried out by using the Generalized Centroid Difference (GCD) technique for several states of 131,132I nuclei, produced from decay of the radio-chemically separated fission products

  10. Separation of cesium from simulated active waste using zinc hexacyanoferrate supported composite

    International Nuclear Information System (INIS)

    Potassium zinc hexacyanoferrate (KZnHCF) was prepared and supported on polyacrylonitrile (PAN) binding polymer. This composite was characterized and used to study the elimination of cesium from acidic radioactive waste containing Sr(II), Eu(II), Am(II), Zr(IV), Hf(IV) and Nb(V) using batch and column techniques. The sorption capacity of this composite for cesium was found to be 1.14 meq/g for column technique. The effect of presence of NH4SCN, NaNo3 and other complexing agents in the aqueous solutions was studied

  11. A preliminary deposit model for lithium-cesium-tantalum (LCT) pegmatites

    Science.gov (United States)

    Bradley, Dwight; McCauley, Andrew

    2013-01-01

    This report is part of an effort by the U.S. Geological Survey to update existing mineral deposit models and to develop new ones. We emphasize practical aspects of pegmatite geology that might directly or indirectly help in exploration for lithium-cesium-tantalum (LCT) pegmatites, or for assessing regions for pegmatite-related mineral resource potential. These deposits are an important link in the world’s supply chain of rare and strategic elements, accounting for about one-third of world lithium production, most of the tantalum, and all of the cesium.

  12. Heat Transfer During Evaporation of Cesium From Graphite Surface in an Argon Environment

    Directory of Open Access Journals (Sweden)

    Bespala Evgeny

    2016-01-01

    Full Text Available The article focuses on discussion of problem of graphite radioactive waste formation and accumulation. It is shown that irradiated nuclear graphite being inalienable part of uranium-graphite reactor may contain fission and activation products. Much attention is given to the process of formation of radioactive cesium on the graphite element surface. It is described a process of plasma decontamination of irradiated graphite in inert argon atmosphere. Quasi-one mathematical model is offered, it describes heat transfer process in graphite-cesium-argon system. Article shows results of calculation of temperature field inside the unit cell. Authors determined the factors which influence on temperature change.

  13. Synthesis of novel calixcrown derivatives with selective complexation towards cesium ions

    Institute of Scientific and Technical Information of China (English)

    Lu Zhang; Juan Du; Li Hua Yuan; Dong Zhang; Gui Ping Dan; Yuan You Yang; Wen Feng

    2011-01-01

    A series of novel calix [4]arenecrown-6 derivatives with an alkenyl loop of various sizes 5-8 were synthesized via intramolecular ring closing olefin metathesis and characterized by 1H NMR, 13C NMR and ESI-HRMS. Their complexation property towards cesium ion was studied by 'H NMR technique. Two-phase extraction of alkali metal ions using UV-vis spectroscopy revealed remarkably different extractabilities. These results indicate that the complexation capacities towards cesium ions can be tuned and controlled through cooperative regulation of the strain of the loop and conformational change of calixcrown skelton.

  14. Measurement of Ionization Threshold of Ultracold Cesium Rydberg Atoms in Static Electric Field

    Institute of Scientific and Technical Information of China (English)

    FENG Zhi-Gang; ZHANG Lin-Jie; ZHAO Jian-Ming; LI Chang-Yong; LI An-Ling; JIA Suo-Tang

    2008-01-01

    We investigate the field ionization spectra of ultracold cesium Rydberg atoms in dc electric field. The ionization thresholds of different electric fields are measured and shift of the ionization threshold relative to field-free ionization threshold is accurately described by (6.06±0.14) F1/2, which is in good agreement with the classical saddle-point model for field ionization. We obtain the field-free ionization threshold of cesium (6P,3/2) as 19674.89士2.99cm-1 by fitting experimental data.

  15. A direct frequency comb for two-photon transition spectroscopy in a cesium vapor

    Institute of Scientific and Technical Information of China (English)

    Zhang Yi-Chi; Wu Ji-Zhou; Li Yu-Qing; Jin Li; Ma Jie; Wang Li-Rong; Zhao Yan-Ting; Xiao Lian-Tuan; Jia Suo-Tang

    2012-01-01

    A phase-stabilized femtosecond frequency comb is used to measure high-resolution spectra of two-photon transition 62S1/2-62P1/2,3/2-82S1/2 in a cesium vapor.The broadband laser output from a femtosecond frequency comb is split into counter-propagating parts,shaped in an original way,and focused into a room-temperature cesium vapor.We obtain high-resolution two-photon spectroscopy by scanning the repetition rate of femtosecond frequency comb,and through absolute frequency measurements.

  16. Recent progress in optically-pumped cesium beam clock at Peking University

    Science.gov (United States)

    Liu, C.; Zhou, S.; Wan, J.; Wang, S.; Wang, Y.

    2016-06-01

    A compact, long-life, and low-drift cesium beam clock is investigated at Peking University, where the atoms are magnetic-state selected and optically detected. Stability close to that of the best commercial cesium clocks has been achieved from 10 to 105 s. As previously shown, the short-term stability is determined by atomic shot noise or laser frequency noise. The stabilizations of microwave power and C-field improve the long-term stability, with the help of a digital servo system based on field-programmable gate array.

  17. Separation of cesium from rad waste solutions with hexacyanoferrate(II) resins of copper and cobalt

    International Nuclear Information System (INIS)

    The separation of radiocesium from low and intermediate level waste solutions by ion exchange with potassium cobalt hexacyanoferrate(II) and potassium copper-cobalt hexacyanoferrate(II) loaded resins was studied. The distribution coefficient(Kd) of cesium as a function of sodium ion concentration was determined. High batch capacity of these resins with regards to cesium make them ideal sorbents that can be used in once through mode in the treatment of rad waste solutions. (author). 3 refs., 1 fig., 1 tab

  18. Concentration Ratios for Cesium and Strontium in Produce Near Los Alamos

    Energy Technology Data Exchange (ETDEWEB)

    S. Salazar, M.McNaughton, P.R. Fresquez

    2006-03-01

    The ratios of the concentrations of radionuclides in produce (fruits, vegetables, and grains) to the concentrations in the soil have been measured for cesium and strontium at locations near Los Alamos. The Soil, Foodstuffs, and Biota Team of the Meteorology and Air Quality Group of the Los Alamos National Laboratory (LANL) obtained the data at locations within a radius of 50 miles of LANL. The concentration ratios are in good agreement with previous measurements: 0.01 to 0.06 for cesium-137 and 0.1 to 0.5 for strontium-90 (wet-weight basis).

  19. Computational study of organo-cesium complexes and the possibility of lanthanide/actinide ions substitution

    Science.gov (United States)

    Rabanal-León, Walter A.; Martinez-Ariza, Guillermo; Roberts, Sue A.; Hulme, Christopher; Arratia-Pérez, Ramiro

    2015-11-01

    Relativistic DFT calculations suggest that two organo-cesium complexes studied herein afford large HOMO-LUMO gaps of around 2.4 eV with the PBE xc-functional, which accounts for their stability. Energy decomposition studies suggest these two complexes are largely ionic with about 20% covalency. However, when the Cs+ ions are substituted by the isoelectronic La3+ and Th4+, their predicted ionicity decreases significantly. The significant increase in covalence indicates that employing Ugi reaction cascades that afford tetramic acid-based organo-cesium complexes may be extended to La3+ and Th4+ organometallics.

  20. Stability studies of therapeutic 131I-meta-iodobenzylguanidine (131I-mIBG) using high performance liquid chromatography

    International Nuclear Information System (INIS)

    BRIT is a manufacturer and supplier of therapeutic doses (100 mCi) of the radiopharmaceutical 131I-mIBG to various nuclear medicine centers in India. The therapeutic formulation is of high radioactive concentration (>10 mCi/ml) and is thus prone to radiolytic damage during transport, storage until administration. Earlier stability studies at this laboratory were done using conventional methods like Thin Layer Chromatography (TLC) which has an inherent limitation in terms of resolution. In view of this, a suitable HPLC method has been developed and the stability of therapeutic 131I-mIBG was monitored at various conditions

  1. Methodology to administer therapeutic dose of I-131

    International Nuclear Information System (INIS)

    The present work suggests the use of measures guided to eliminate the resulting chronic sialoadenitis of the treatment of the thyroid cancer with Iodine-131, as well as the use of citric fruits to stimulate the salivation, the post-dose administration of liquids to accelerate the gastric emptying avoiding the secondary effects as the vomit is included. (Author)

  2. Microdeletion in distal 17p13.1

    DEFF Research Database (Denmark)

    Zeesman, Susan; Kjaergaard, Susanne; Hove, Hanne Buciek;

    2012-01-01

    Array comparative genomic hybridization has led to the identification of new syndromes by identifying genomic imbalances not detectable by standard karyotyping methods and by allowing correlations with physical findings. Deletions in the 17p13.1 region have been reported in patients with dysmorph...

  3. 131-Iodine-Labeled Derivatives of the Sonic Hedgehog Protein

    Directory of Open Access Journals (Sweden)

    Jennifer Sims-Mourtada

    2012-01-01

    Full Text Available Activation of hedgehog (HH pathway signaling is observed in many tumors. Due to a feedback loop, the HH receptor Patched (PTCH-1 is overexpressed in tumors with activated HH signaling. Therefore, we sought to radiolabel the PTCH-1 ligand sonic (SHH for detection of cancer cells with canonical HH activity. Receptor binding of 131I-SHH was increased in cell lines with high HH pathway activation. Our findings also show that PTCH-1 receptor expression is decreased upon treatment with HH signaling inhibitors, and receptor binding of 131I-SHH is significantly decreased following treatment with cyclopamine. In vivo imaging and biodistribution studies revealed significant accumulation of 131I-SHH within tumor tissue as compared to normal organs. Tumor-to-muscle ratios were approximately 8 : 1 at 5 hours, while tumor to blood and tumor to bone were 2 : 1 and 5 : 1, respectively. Significant uptake was also observed in liver and gastrointestinal tissue. These studies show that 131I-SHH is capable of in vivo detection of breast tumors with high HH signaling. We further demonstrate that the hedgehog receptor PTCH-1 is downregulated upon treatment with hedgehog inhibitors. Our data suggests that radiolabeled SHH derivatives may provide a method to determine response to SHH-targeted therapies.

  4. 49 CFR 37.131 - Service criteria for complementary paratransit.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 1 2010-10-01 2010-10-01 false Service criteria for complementary paratransit. 37... FOR INDIVIDUALS WITH DISABILITIES (ADA) Paratransit as a Complement to Fixed Route Service § 37.131 Service criteria for complementary paratransit. The following service criteria apply to...

  5. Biodistribution of 131I-Herceptin in breast cancer xenograft

    International Nuclear Information System (INIS)

    Objective: to establish Her-2 positive SK-BR-3 human breast cancer xenografts in athymic mice. To explore the biologic distribution of 131I-herceptin in human breast cancer xenografts. Methods: Implant SK-BR-3 cells subcutaneously to BALB/c-neu athymic mice to establish animal model. To measure the radiocounting per minute (cpm) of every organ on a γ arithmometer at 4, 12, 24, 48 h postinjection of 131I-Herceptin or 131I-mIgG, then to gain the T/NT ratios and the uptakes percentage per gram of the injection dose (% ID/g). Results: After subcutaneously planted, a 96% of tumor forming rate was achieved. Compared with the control group, bigger T/NT and % ID/g was obtained in the experimental group (P<0.05 and <0.01). Conclusion: A high tumor forming rate can be get by implanting SK-BR-3 cells subcutaneously to athymic mouse, 131I-Herceptin is obviously concentrated in tumor tissues. (authors)

  6. 10 CFR 455.131 - State ranking of grant applications.

    Science.gov (United States)

    2010-01-01

    ... energy conservation potential, on a savings percentage basis, of the building as determined in the energy... conservation measure which is physically connected to all of the buildings. If a State ranks on a measure-by....131 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION GRANT PROGRAMS FOR SCHOOLS AND HOSPITALS...

  7. 45 CFR 1706.131-1706.139 - [Reserved

    Science.gov (United States)

    2010-10-01

    ... Welfare Regulations Relating to Public Welfare (Continued) NATIONAL COMMISSION ON LIBRARIES AND INFORMATION SCIENCE ENFORCEMENT OF NONDISCRIMINATION ON THE BASIS OF HANDICAP IN PROGRAMS OR ACTIVITIES CONDUCTED BY NATIONAL COMMISSION ON LIBRARIES AND INFORMATION SCIENCE §§ 1706.131-1706.139...

  8. 47 CFR 74.131 - Licensing requirements, necessary showing.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 4 2010-10-01 2010-10-01 false Licensing requirements, necessary showing. 74... Experimental Broadcast Stations § 74.131 Licensing requirements, necessary showing. (a) An applicant for a new... research and experimentation in the technical phases of broadcasting which indicates reasonable promise...

  9. 40 CFR 92.131 - Smoke, data analysis.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Smoke, data analysis. 92.131 Section... analysis. The following procedure shall be used to analyze the smoke test data: (a) Locate each throttle... standards of subpart A of this part for determination of compliance. (d) This smoke trace analysis may...

  10. National intercomparison of activity measurements with iodine-131

    International Nuclear Information System (INIS)

    To coordinate the isotope measurements in India and to make these measurements traceable to the national Primary Standards, a national intercomparison of activity measurements with the radioisotope iodine-131 was organized. This is the first intercomparison and iodine-131 was selected because it is extensively used in nuclear medicine. Other radioisotopes of interest will be taken up in future. Standardized solutions of iodine-131 were sent to the participants without disclosing the true activity of sample. They were asked to measure on their detection system and report the activity of the sample alongwith the details of the measuring system. This report describes briefly the organization of the intercomparison, preparation of samples of iodine-131, primary standardization and international intercomparison. The results of measurement as well as the details of measuring systems used by the participants are included. Finally, based on the experience of this intercomparison some recommendations are given for the participants to enable them to make measurements with better accuracy and reliability. (author)

  11. X-ray imaging performance of structured cesium iodide scintillators.

    Science.gov (United States)

    Zhao, Wei; Ristic, Goran; Rowlands, J A

    2004-09-01

    Columnar structured cesium iodide (CsI) scintillators doped with Thallium (Tl) have been used extensively for indirect x-ray imaging detectors. The purpose of this paper is to develop a methodology for systematic investigation of the inherent imaging performance of CsI as a function of thickness and design type. The results will facilitate the optimization of CsI layer design for different x-ray imaging applications, and allow validation of physical models developed for the light channeling process in columnar CsI layers. CsI samples of different types and thicknesses were obtained from the same manufacturer. They were optimized either for light output (HL) or image resolution (HR), and the thickness ranged between 150 and 600 microns. During experimental measurements, the CsI samples were placed in direct contact with a high resolution CMOS optical sensor with a pixel pitch of 48 microns. The modulation transfer function (MTF), noise power spectrum (NPS), and detective quantum efficiency (DQE) of the detector with different CsI configurations were measured experimentally. The aperture function of the CMOS sensor was determined separately in order to estimate the MTF of CsI alone. We also measured the pulse height distribution of the light output from both the HL and HR CsI at different x-ray energies, from which the x-ray quantum efficiency, Swank factor and x-ray conversion gain were determined. Our results showed that the MTF at 5 cycles/mm for the HR type was 50% higher than for the HL. However, the HR layer produces approximately 36% less light output. The Swank factor below K-edge was 0.91 and 0.93 for the HR and HL types, respectively, thus their DQE(0) were essentially identical. The presampling MTF decreased as a function of thickness L. The universal MTF, i.e., MTF plotted as a function of the product of spatial frequency f and CsI thickness L, increased as a function of L. This indicates that the light channeling process in CsI improved the MTF of

  12. Evaluation of {sup 131}I retention in several adsorbers

    Energy Technology Data Exchange (ETDEWEB)

    Catanoso, Marcela F.; Osso Junior, Joao Alberto, E-mail: marcela.forli@gmail.co, E-mail: jaosso@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Diretoria de Radiofarmacia

    2011-07-01

    Several iodine radioisotopes are used in nuclear medicine for treatment and diagnostic purposes. The radioisotope {sup 131}I is used both in diagnosis and therapy due to its physical characteristics of decay by {beta}{sup -} and its {gamma}-ray emissions suitable for diagnosis. It is routinely produced at IPEN through the irradiation of TeO{sub 2} targets in the IEA-R1m nuclear reactor. After the irradiation, the {sup 131}I is separated by dry distillation, where the targets are put in an oven, heated at 760 deg C for 2 hours and the {sup 131}I, volatile, is carried by an O{sub 2} gas stream. The aim of this work was to evaluate the retention and elution of {sup 131}I samples produced at IPEN in several adsorbers as part of a project aiming the purification of these radioisotopes, allowing the labeling of biomolecules. Samples of {sup 131}I were used for retention and elution studies with the following adsorbers: commercial cartridges, anionic resin columns and cationic resin column. The results showed that Ag cartridges and anionic resins Dowex 1X8, Dowex 3 and IRA 400 had a great iodine retention but no elution after using specific eluents. The QMA light, acid alumina, neutral alumina and cationic resin Dowex 50WX4 showed high retention and elution and QMA plus and cationic resin Dowex 50WX8 and Dowex 50WX12 had a good retention but lower elution. Regarding to the better retention and elution, Ag cartridges and resins showed a higher percentage of iodine retention but lower elution yield and QMA light, acid and neutral alumina cartridges showed better results. (author)

  13. Evaluation of 131I retention in several adsorbers

    International Nuclear Information System (INIS)

    Several iodine radioisotopes are used in nuclear medicine for treatment and diagnostic purposes. The radioisotope 131I is used both in diagnosis and therapy due to its physical characteristics of decay by β- and its γ-ray emissions suitable for diagnosis. It is routinely produced at IPEN through the irradiation of TeO2 targets in the IEA-R1m nuclear reactor. After the irradiation, the 131I is separated by dry distillation, where the targets are put in an oven, heated at 760 deg C for 2 hours and the 131I, volatile, is carried by an O2 gas stream. The aim of this work was to evaluate the retention and elution of 131I samples produced at IPEN in several adsorbers as part of a project aiming the purification of these radioisotopes, allowing the labeling of biomolecules. Samples of 131I were used for retention and elution studies with the following adsorbers: commercial cartridges, anionic resin columns and cationic resin column. The results showed that Ag cartridges and anionic resins Dowex 1X8, Dowex 3 and IRA 400 had a great iodine retention but no elution after using specific eluents. The QMA light, acid alumina, neutral alumina and cationic resin Dowex 50WX4 showed high retention and elution and QMA plus and cationic resin Dowex 50WX8 and Dowex 50WX12 had a good retention but lower elution. Regarding to the better retention and elution, Ag cartridges and resins showed a higher percentage of iodine retention but lower elution yield and QMA light, acid and neutral alumina cartridges showed better results. (author)

  14. Comparative biodistribution profile of [131I]VIP and [131I]VIP10-28

    Directory of Open Access Journals (Sweden)

    Maria Tereza Colturato

    2005-10-01

    Full Text Available Various tumor cells express significantly higher amounts of VIP receptors (VIPR that provided the basis for the clinical use of radiolabeled VIP for the in vivo localization of tumors. This work studied the labeling of VIP and VIP10-28 with iodine-131 to compare the biological distribution of the labeled compounds in Nuce mice and the affinity for tumor cells. Both VIP and VIP10-28 peptides contain two tyrosine residues, in positions 10 and 22, that are theoretically equally susceptible to radioiodination employing oxidative electrophilic substitution using oxidizing agents like Chloramine T. Radiochemical purity of the reaction mixture was determined by electrophoresis and HPLC. The VIP peptide and the fragment were labeled with radioiodine with good radiochemical yield (above 96%. Suitable, but important differences can be observed in biological distribution studies. Comparatively, blood clearance was faster for labeled VIP and perhaps because of this, the uptake in tumor was lower, especially during the first hour. These differences observed in the biological distribution of the compounds can be related to the lipophilicity of the labeled compounds.Várias células tumorais expressam significantemente uma alta quantidade de receptores VIP (VIPR que determinam a base para o uso clínico de VIP radiomarcado para localização de tumores in vivo. Foi estudado neste trabalho a marcação do VIP e do fragmento VIP10-28 com iodo-131 comparando a distribuição biológica dos compostos marcados em camundongos Nude e sua afinidade pelas células tumorais. Ambos os peptídeos, VIP e VIP10-28. contém dois resíduos de tirosina nas posições 10 e 22, que teoricamente são igualmente susceptíveis pela substituição eletrofílica oxidativa do radioiodo utilizando Cloramina T como agente oxidante. A pureza radioquímica da mistura de reação foi determinada por eletroforese e cromatografia líquida de alta eficiência (CLAE. O VIP e fragmento foram

  15. Physical barrier effect of geopolymeric waste form on diffusivity of cesium and strontium.

    Science.gov (United States)

    Jang, J G; Park, S M; Lee, H K

    2016-11-15

    The present study investigates the physical barrier effect of geopolymeric waste form on leaching behavior of cesium and strontium. Fly ash-based geopolymers and slag-blended geopolymers were used as solidification agents. The leaching behavior of cesium and strontium from geopolymers was evaluated in accordance with ANSI/ANS-16.1. The diffusivity of cesium and strontium in a fly ash-based geopolymer was lower than that in Portland cement by a factor of 10(3) and 10(4), respectively, showing significantly improved immobilization performance. The leaching resistance of fly ash-based geopolymer was relatively constant regardless of the type of fly ash. The diffusivity of water-soluble cesium and strontium ions were highly correlated with the critical pore diameter of the binder. The critical pore diameter of the fly ash-based geopolymer was remarkably smaller than those of Portland cement and slag-blended geopolymer; consequently, its ability physically to retard the diffusion of nuclides (physical barrier effect) was superior.

  16. Immobilisation of radio cesium loaded ammonium molybdo phosphate in glass matrices

    International Nuclear Information System (INIS)

    Long half life and easy availability from high level wastes make 137Cesium most economical radiation source. High level liquid waste processing for 137 Cesium removal has become easier due to development of Cesium specific granulated ammonium molybdophosphate (AMP) composite. In such applications, resulting spent composite AMP itself represents high active solid waste and immobilization of these materials in cement may not be acceptable. Studies on immobilization of 137Cs loaded AMP were taken up in order to achieve twin goals of increasing safety and minimizing processing costs of the final matrix. Studies indicated that phosphate modified sodium borosilicate SPNM glasses prepared under usual oxidizing conditions are not suitable for immobilization of 137Cs loaded on AMP .Phosphate glasses containing Na2O, P2O5, B2O3, Fe2O3, Al2O3 and SiO2 as major constituents are capable of incorporating 6 to 8 % AMP. The Normalized Leach rates of these glasses for sodium, cesium, boron and silica are 10-4 to 10-6 gm/cm2/day which are comparable to or better than those reported for NBS glasses incorporating HLW. Homogeneity of the final matrix was confirmed by x-ray diffraction analysis. Further studies on characterization of these glasses would establish their acceptability. (author)

  17. Removal of cesium ions from waste solution using sericite incorporated into nickel hexacyanoferrate

    Energy Technology Data Exchange (ETDEWEB)

    Jeon, Choong; Cha, Ju-Hyun [Gangneung-Wonju National University, Wonju (Korea, Republic of)

    2015-11-15

    To increase adsorption capacity and selectivity for cesium ions from waste solution, sericite was chemically modified by means of nickel hexacyanoferrate (NiHCF) with a high selectivity trap agent for cesium. Scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) spectroscopy were used for the characteristic analysis of surface onto the NiHCF-sericite. The adsorption capacity of cesium ions for the NiHCF-sericite increased about 2.5 times, as compared with natural sericite at initial pH 5.0 of waste solution. Adsorption equilibrium was investigated by Langmuir and Freundlich isotherm model, respectively. Maximum adsorption capacity was estimated as 16.583mg/g, and the Langmuir isotherm fits the adsorption data better than Freundlich model. The adsorption process was determined as an exothermic reaction and all adsorption was completed in 30 min. In addition, the adsorption capacity of cesium ions was not greatly affected by ionic strength (-0.1M NaCl concentration) and other metals in mixed waste solution.

  18. Assessment of commercially available ion exchange materials for cesium removal from highly alkaline wastes

    Energy Technology Data Exchange (ETDEWEB)

    Brooks, K.P.; Kim, A.Y.; Kurath, D.E.

    1996-04-01

    Approximately 61 million gallons of nuclear waste generated in plutonium production, radionuclide removal campaigns, and research and development activities is stored on the Department of Energy`s Hanford Site, near Richland, Washington. Although the pretreatment process and disposal requirements are still being defined, most pretreatment scenarios include removal of cesium from the aqueous streams. In many cases, after cesium is removed, the dissolved salt cakes and supernates can be disposed of as LLW. Ion exchange has been a leading candidate for this separation. Ion exchange systems have the advantage of simplicity of equipment and operation and provide many theoretical stages in a small space. The organic ion exchange material Duolite{trademark} CS-100 has been selected as the baseline exchanger for conceptual design of the Initial Pretreatment Module (IPM). Use of CS-100 was chosen because it is considered a conservative, technologically feasible approach. During FY 96, final resin down-selection will occur for IPM Title 1 design. Alternate ion exchange materials for cesium exchange will be considered at that time. The purpose of this report is to conduct a search for commercially available ion exchange materials which could potentially replace CS-100. This report will provide where possible a comparison of these resin in their ability to remove low concentrations of cesium from highly alkaline solutions. Materials which show promise can be studied further, while less encouraging resins can be eliminated from consideration.

  19. Transfer of radioactive cesium from soil to rape plants, rape blossoms and rape honey

    International Nuclear Information System (INIS)

    Due to the test of atomic weapons and the accident in the nuclear power plant at Chernobyl, the vegetation in Germany has been exposed to cesium contamination in the soil. It was to be expected that activity would migrate from soil to plants and to food products. In this work, the transfer of radioactive cesium from soil to rape plants (Brassica napus var. oleifera), rape blossoms and further to rape honey was investigated. By measuring the gamma activity of cesium using germanium detectors with measuring capacity up to 30 h per sample (limit of detection about 0.14 Bq/kg to 0.19 Bq/kg), we determined a mean transfer factor fcs = 0,116 ± 0,080 for the system soil-rape plant, fcs = 0.065 + 0.075 for the system soil-rape blossom and F!S = 0.098 + 0.044 for the system soil-rape honey (plants and honey wet mass, soil dry mass) (Table IV). Additionally, for the transfer of cesium from rape plants to rape honey, a factor of fcs = 2.04 ± 7.23 (both wet mass) was determined. Due to some environmental circumstances, which can hardly ever be taken into account, the results obtained sometimes differ considerably. Nevertheless, the mean transfer factors are within the range of values found in literature (Table V)

  20. Cesium-137 and americium-241 distribution by granulometric fractions of soil at Azgir test site grounds

    International Nuclear Information System (INIS)

    In measurements of radionuclide specific content in surface soil layer of contaminated territories it is important to determine in what agglomerations of soil particles there is the highest radionuclide concentration. For this purpose granulometric composition of soil at Azgir test site was studied and cesium-137 and americium-241 distribution by soil fractions was researched. (author)

  1. Strontium-90 and cesium-137 in sea fish (from Jun. 1982 to Dec. 1982)

    International Nuclear Information System (INIS)

    Strontium-90 and cesium-137 in sea fish (from Jun. to Dec. 1982) were determined. Fish was collected from 22 sampling locations. Only the edible part was used in case of larger sized fish, and the whole part was used in case of smaller ones. The results are sown in a table. (Namekawa, K.)

  2. Strontium-90 and cesium-137 in sea fish (from Nov. 1982 to Jun. 1983)

    International Nuclear Information System (INIS)

    Strontium-90 and cesium-137 in sea fish (from Nov. 1982 to Jun. 1983) were determined. Fishes were collected from eight sampling locations. Only the edible part was used in case of larger sized fish, and the whole part was used in case of smaller ones. The results are shown in a table. (J.P.N.)

  3. Strontium-90 and cesium-137 in sea fish (from Oct. 1981 to Jun. 1982)

    International Nuclear Information System (INIS)

    Strontium-90 and cesium-137 in sea fishes (from Oct. 1981 to Jun. 1982) were determined. Fish was collected from eight sampling locations. Only the edible part was used in case of larger sized fish, and the whole part was used in case of smaller ones. The results are shown in a table. (Namekawa, K.)

  4. Leachability of cobalt and cesium from natural and chemically treated zeolites

    International Nuclear Information System (INIS)

    The determination of leachability of radioisotopes of cesium and cobalt from preloaded zeolites in distilled water, base solution and acid solution has been studied. For the experiment, we used natural and chemically treated zeolites. The zeolites before leaching were calcined at different temperatures. (author). 8 refs., 5 figs., 2 tabs

  5. Nanophotonic hybridization of narrow atomic cesium resonances and photonic stop gaps of opaline nanostructures

    NARCIS (Netherlands)

    Harding, P.J.; Pinkse, P.W.H.; Mosk, A.P.; Vos, W.L.

    2015-01-01

    We study a hybrid system consisting of a narrow-band atomic optical resonance and the long-range periodic order of an opaline photonic nanostructure. To this end, we have infiltrated atomic cesium vapor in a thin silica opal photonic crystal. With increasing temperature, the frequencies of the opal'

  6. Electromagnetically-induced transparency in a multi-V-type system in cesium atomic vapour

    Institute of Scientific and Technical Information of China (English)

    赵建明; 尹王保; 汪丽蓉; 肖连团; 贾锁堂

    2002-01-01

    Electromagnetically-induced transparency is observed in a three-level multi-V-type system in cesium vapour atroom temperature. The absorption property is measured and the hyperfine structures of atomic states can be determined.The results of the experiment agree with the theoretical analysis.

  7. Dual cesium and rubidium atomic fountain with a 10-16 level accuracy and applications

    International Nuclear Information System (INIS)

    Atomic fountains are the most accomplished development of the atomic clocks based on the cesium atom whose hyperfine resonance defines the SI second since 1967. Today these systems are among those which realize the second with the best accuracy. We present the last developments of the cold cesium and rubidium atom dual fountain experiment at LNE-SYRTE. This unique dual setup would allow to obtain an outstanding resolution in fundamental physics tests based on atomic transition frequency comparisons. In order to enable operation with both atomic species simultaneously, we designed, tested and implemented on the fountain new collimators which combine the laser lights corresponding to each atom. By comparing our rubidium fountain to another cesium fountain over a decade, we performed a test of the stability of the fine structure constant at the level of 5 * 10-16 per year. We carried on the work on the clock accuracy and we focused on the phase gradients effects in the interrogation cavity and on the microwave leakage. The fountain accuracy has been evaluated to 4 * 10-16 for the cesium clock and to 5 * 10-16 for the refurbished rubidium clock. As a powerful instrument of metrology, our fountain was implicated in many clock comparisons and contributed many times to calibrate the International Atomic Time. Furthermore, we used the fountain to perform a new test of Lorentz local invariance. (author)

  8. Separation of cesium-137 from uranium fission products via a NeoflonR column supporting tetraphenylboron

    International Nuclear Information System (INIS)

    Cesium is a member of the Group I alkali metals, very reactive earth metals that react vigorously with both air and water. The chemistry of cesium is much like the chemistry of neighboring elements on the periodic table, potassium and rubidium. This close relation creates many problems in plant-life exposed to cesium because it is so easily confused for potassium, an essential nutrient to plants. Radioactive 134Cs and 137Cs are also chemically akin to potassium and stable cesium. Uptake of these radioactive isotopes from groundwater by plant-life destroys the plant-life and can potentially expose humans to the radioactive affects of 134Cs and 137Cs. Much experimental work has been focused on the separation of 137Cs from uranium fission products. In previous experimental work performed a column consisting of Kel-F supporting tetraphenylboron (TPB) was utilized to separate 137Cs from uranium fission products. It is of interest at this time to attempt the separation of 134Cs from 0.01M EDTA using the same method and Neoflon in the place of Kel-F as the inert support. The results of this experiment give a separation efficiency of 88% and show a linear relationship between the column bed length and the separation efficiency obtained. (author)

  9. Cesium Sorption from Concentrated Acidic Tank Wastes Using Ammonium Molybdophosphate-polyacrylonitrile Composite Sorbents

    Energy Technology Data Exchange (ETDEWEB)

    Todd, Terry Allen; Mann, Nicholas Robert; Tranter, Troy Joseph; Sebesta, F.; John, J.; Motl, A.,

    2002-10-01

    Ammonium molybdophosphate-polyacrylonitrile (AMP-PAN) composite sorbents have been evaluated for the removal of cesium from Idaho National Engineering and Environmental Laboratory (INEEL) concentrated acidic tank waste. Batch contacts were performed to qualitatively evaluate the effects of increased nitric acid, sodium and potassium. An equilibrium isotherm was generated with simulated concentrated tank waste solutions and fit to the Langmuir equation. Additional batch contact experiments were performed to determine if mercury, plutonium and americium would sorb onto AMP-PAN. Dynamic sorption was evaluated in column tests employing 1.5 cm3 columns operating at 5, 10 and 20 bed volumes of flow per hour. Results indicate, as expected, that dynamic cesium sorption capacity is reduced as the flowrate is increased. Calculated dynamic capacities for cesium were 22.5, 19.8 and 19.6 mg Cs/g sorbent, for 5, 10 and 20 bed volume per hour flows, respectively. The thermal stability of loaded AMP-PAN was evaluated by performing thermogrovimetric analysis (TGA) on samples of AMP, PAN (polymer), and AMP-PAN. Results indicate that AMP-PAN is stable to 400 °C, with less than a 10% loss of weight, which is at least partially due to loss of water of hydration. The evaluation of AMP-PAN indicates that it will effectively remove cesium from concentrated acidic tank waste solutions.

  10. Sorption behavior of cesium from aqueous solution on magnetic hexacyanoferrate materials

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Hengxuan; Zhao, Xuan, E-mail: zhxinet@tsinghua.edu.cn; Wei, Jiying; Li, Fuzhi

    2014-08-15

    Highlights: • A novel pathway of synthesizing magnetic hexacyanoferrate material was developed. • The synthesized material can offer a high capacity for sorption of cesium. • The material can offer a fast removal of cesium in kinetic performance. • The fine M-PTH particle can be easily separated from wastewater for recirculation. - Abstract: The rapid development of the nuclear power plant in China leads to increasing attention to the treatment of low-level radioactive wastewater (LLRW). One of possibilities is the application of inorganic adsorbent like potassium titanium hexacyanoferrate (PTH), which can exhibit the effective adsorption of cesium. In this paper, the PTH material was optimized by means of being loaded on magnetite substrate. The synthesized material (magnetic PTH, M-PTH), with a particle size of less than 100 nm, can offer a high capacity and favorable kinetic performance, however, without difficulties of separation from the LLRW due to its magnetic characterizations. The batch experiments demonstrate that cesium sorption isotherm of M-PTH coincide well with Langmuir model. The calculated capacity amounts to 0.517 mmol/g, approximately 1.5 times the capacity of zeolite materials. The sorption process follows the pseudo-second-order sorption model. In the initial phase the rate-controlling step is intraparticle diffusion. With the Cs accumulation on the particle surface, external diffusion performs an important role together with intraparticle diffusion.

  11. Z' indication from new APV data in Cesium and searches at linear colliders

    OpenAIRE

    Casalbuoni, R.; De Curtis, S.; Dominici, D.; Gatto, R.; Riemann, S.

    2000-01-01

    New data on parity violation in atomic cesium can be explained by a new neutral vector boson almost unmixed with Z, with a mass in the TeV range and sizeable couplings to the fermions. The properties of such additional Z' can be investigated at future linear colliders.

  12. Cobalt-60 and cesium-137 for the sterilization of food. Radiation treatment of food

    International Nuclear Information System (INIS)

    The brief article discusses the reasons justifying in the eyes of the authors the irradiation of food with ionizing readiation, the irradiation technique applied using cobalt-60 and cesium-137 as a radiation source, and the possible secondary effects of the method. (VHE)

  13. High-temperature cesium capture using activated kaolinite in the presence of chlorine and volatile heavy metals

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Hee Chul; Kim, Jeoung Guk; Yoo, Jae Hyung; Kim, Joon Hyung [KAERI, Taejon (Korea, Republic of); Yoon, Jong Sung [Chungnam National Univ., Taejon (Korea, Republic of)

    2002-05-01

    This study investigated the use of porous activated kaolin particles in the size range of 300- 400 {mu}m as high-temperature sorbents for cesium capture in the presence of chlorine and/or in the presence of cadmium and lead. Packed bed sorption tests by passing CsCl-carrying flue gas through the packed bed of activated porous kaolin particles were first performed at the temperature range of 973-1173 K and a CsCl partial pressure range of 7.4-11.1 Pa. The observed structural change of the sorbent mineral at the stage of sorption revealed the characteristics of an irreversible chemical reaction as a major cesium capturing mechanism. In the fully saturated kaolin sorbent, Cs{sub 2}O{center_dot}Al{sub 2}O{sub 3}{center_dot}SiO{sub 2} is present as a sorption reaction product, together with much smaller amount of water-soluble cesium species. The increase in sorbent bed temperature resulted in an increase in the rate of sorption, but it had no effect on maximum cesium uptake. In the presence of other condensable gas-phase metal chlorides such as cadmium and lead, cesium was preferentially adsorbed onto tested activated kaolinite, but a half of cesium appeared to be physically-sorbed cesium species, CsCl.

  14. Foliar uptake of cesium, iodine and strontium and their transfer to the edible parts of beans, potatoes and radishes

    Science.gov (United States)

    Oestling, O.; Kopp, P.; Burkart, W.

    Considerable fractions of radionuclide solutions deposited on the surface of the leaves may be transferred to the edible parts of plants. In radishes we observed a transfer of more than 40% of the applied cesium radioisotope within a few days. A rather similar uptake was found for beans and potatoes when harvested a month after application of radioactivity. As much as 60% of the applied cesium-isotope remained in (or on) the potato leaves even 8 days after application. The major part could however be washed off the leaves a few hours after application. When radishes were showered with water within 7 h after the application of activity the uptake was greatly reduced. No competitive effect of potassium chloride for the foliar uptake of cesium was found. A 10 -2 M colloidal suspension of Prussian Blue, a chelating agent for monovalent alkali metals such as potassium, cesium, or other monovalent cations, applied as droplets to the leaves one day prior to application of active cesium was found to strongly inhibit the transfer of cesium to the radish. The transfer of iodine and strontium to the edible parts was found to be negligible (or slower) as compared to cesium. In most cases no detectable amounts of these two nuclides were transfered to the edible parts of the radish after 2-5 weeks.

  15. Changes in percentage of lymphocyte subsets after 131I treatment in patients with differentiated thyroid cancer

    Institute of Scientific and Technical Information of China (English)

    LUO Quan-Yong; CHEN Li-Bo; YU Yong-Li; LU Han-Kui; ZHU Rui-Sen

    2005-01-01

    To monitor the extent and the duration of lymphocyte subset changes in patients with thyroid carcinoma undergoing therapeutic 131I administration, the percentage of lymphocyte subsets were serially analyzed before and after 131I treatment. In patients who received 1850 MBq of 131I for ablation of thyroid remnants, only for NK cells and B cells showed a significant reduction. In patients received 3700 MBq of 131I for treatment of local lymph node metastases, NK cells, B cells and CD4+ were found decreased. In patients received 7400 MBq of 131I for treatment of distant metastases, NK cells, B cells and CD4+ and CD8+ were all affected. However, there is no significant reduction compared to the baseline in the percentage of all lymphocyte subsets three months after 131I treatment. The results show that the sensitivity of lymphocytes to 131I internal radiation depends upon lymphocyte phenotype and 131I activity. The immunosuppression effects are temporary and reversible.

  16. Observation of radioactive iodine ((131)I, (129)I) in cropland soil after the Fukushima nuclear accident.

    Science.gov (United States)

    Fujiwara, Hideshi

    2016-10-01

    During the early stages of the Fukushima nuclear accident, the temporal variations of (131)I deposited on the ground and of (131)I accumulated in cropland soil were monitored at a fixed location in Japan. Moreover, concentrations of long-lived radioactive iodine ((129)I) in atmospheric deposits and soil were measured to examine the feasibility of retrospectively reconstructing (131)I levels from the levels of accident-derived (129)I. The exceptionally high levels of (131)I in deposits and soil were attributed to rainfall-related deposition of radionuclides. In the crop field studied, the losses of deposited (131)I and (129)I due to volatilization were small. The atomic ratio (129)I/(131)I in the topsoil corresponded to the same ratio in deposits. The (131)I concentrations measured in the topsoil were very consistent with the (131)I concentrations reconstructed from the (129)I concentrations in the soil. PMID:27320744

  17. Vitamin a derivatives labelled with 131I — Potential agents for liver scientigraphy

    Science.gov (United States)

    Kadeřávek, J.; Kozempel, J.; Štícha, M.; Petrášek, J.; Jirsa, M.; Taimr, P.; Lešetický, L.

    2006-01-01

    Two retinol derivatives, 4-[(131I)-4-iodobenzoyloxy]retinol propionate and 4-[(131I)-3-iodobenzylcarbamoyl]retinol propionate, were synthesized and their biodistribution in rats was studied in vivo by the whole body scintigraphy.

  18. Methodology for management of therapeutic dose of I-131; Metodologia para administrar dosis terapeutica de I-131

    Energy Technology Data Exchange (ETDEWEB)

    Basteris M, J.; Gomez D, R. [Universidad Autonoma de Yucatan, Facultad de Medicina, Merida, Yucatan (Mexico)

    2007-07-01

    The present work suggests the use of measures guided to eliminate the resulting chronic sialoadenitis of the treatment previously described with a therapeutic dose bigger than ablative of Iodine 131, as well as the use of citric fruits to stimulate the salivation, the administration of liquid post-dose is included to accelerate the gastric emptying avoiding the secondary effects as the vomit. (Author)

  19. Treatment of hyperthyroidism by 131-iodine; Traitement des hyperthyroidies par l'iode 131: dose calculee versus dose fixe

    Energy Technology Data Exchange (ETDEWEB)

    Fieffe, S.; Cuif-Joba, A.; Testard, A.; Fortuna, I.; Pocharta, J.M.; Papathanassioua, D.; Schvartz, C. [Service d' endocrinologie et medecine nucleaires, institut Jean-Godinot, 1, rue du General Koeing, 51056 Reims, (France)

    2009-05-15

    In a first time, we chose to modify the dose to be administered, on using always the Marinelli formula but on increasing the absorbed dose. In a second time, we wanted to simplify the determination of the dose to be administered by modulating it only in function of the thyroid volume. Two groups of patients were managed for hyperthyroidism recurrence. In a first group the iodine dose ({sup 131}I) was determined with the help of the simplified Marinelli formula: chosen absorbed dose was 150 Gy, gland volume determined by echography, measurement of the fixation at the sixth hour. In the second group, the thyroid volume was determined by echography. The patients with a thyroid from 5 to 30 g received 185 MBq, from 30 to 50 g 370 MBq and superior to 50 g 555 MBq of iodine 131. The two groups of patients have the same characteristics. the results of treatment by iodine 131, evaluated on the dosages of T4L and TSH at three and six months, show the preservation of euthyroidism or the passage in hypothyroidism among 94% of patients in the group 1 and 80% of patients in the group 2. These results are not significantly different. The easiness of the realisation of the treatment in the group 2 lead us to continue this simplified therapy scheme that allows equally to improve the radiation protection of medical personnel by avoiding the use of iodine 131. (N.C.)

  20. Ion exchange kinetics of cesium for various reaction designs using crystalline silicotitanate, UOP IONSIV IE-911

    Science.gov (United States)

    Kim, Sung Hyun

    Through collaborative efforts at Texas A&M University and Sandia National Laboratories, a crystalline silicotitanate (CST), which shows extremely high selectivity for radioactive cesium removal in highly concentrated sodium solutions, was synthesized. The effect of hydrogen peroxide on a CST under cesium ion exchange conditions has been investigated. The experimental results with hydrogen peroxide showed that the distribution coefficient of cesium decreased and the tetragonal phase, the major component of CST, slowly dissolved at hydrogen peroxide concentrations greater than 1 M. A simple and novel experimental apparatus for a single-layer ion exchange column was developed to generate experimental data for estimation of the intraparticle effective diffusivity. A mathematical model is presented for estimation of effective diffusivities for a single-layer column of CST granules. The intraparticle effective diffusivity for Cs was estimated as a parameter in the analytical solution. By using the least square method, the effective diffusivities of 1.56 +/- 0.14 x 10-11 m2/s and 0.68 +/- 0.09 x 10-11 m2/s, respectively, were obtained. The difference in the two values was due to the different viscosities of the solutions. A good fit of the experimental data was obtained which supports the use of the homogeneous model for this system. A counter-current ion exchange (CCIX) process was designed to treat nuclear waste at the Savannah River Site. A numerical method based on the orthogonal collocation method was used to simulate the concentration profile of cesium in the CCIX loaded with CST granules. To maximize cesium loading onto the CST and minimize the volume of CST, two design cases of a moving bed, where the fresh CST is pulsed into the column at certain periods or at certain concentration of cesium, were investigated. Simulation results showed that cesium removal behavior in the pilot-scale test of CCIX experiment, where the column length is 22 ft and the CST is pulsed

  1. Preparation and characterization of cesium-137 aluminosilicate pellets for radioactive source applications

    Energy Technology Data Exchange (ETDEWEB)

    Schultz, F.J.; Tompkins, J.A.; Haff, K.W.; Case, F.N.

    1981-07-01

    Twenty-seven fully loaded /sup 137/Cs aluminosilicate pellets were fabricated in a hot cell by the vacuum hot pressing of a cesium carbonate/montmorillonite clay mixture at 1500/sup 0/C and 570 psig. Four pellets were selected for characterization studies which included calorimetric measurements, metallography, scanning electron microscope and electron backscattering (SEM-BSE), electron microprobe, x-ray diffraction, and cesium ion leachability measurements. Each test pellet contained 437 to 450 curies of /sup 137/Cs as determined by calorimetric measurements. Metallographic examinations revealed a two-phase system: a primary, granular, gray matrix phase containing large and small pores and small pore agglomerations, and a secondary fused phase interspersed throughout the gray matrix. SEM-BSE analyses showed that cesium and silicon were uniformly distributed throughout both phases of the pellet. This indicated that the cesium-silicon-clay reaction went to completion. Aluminum homogeneity was unconfirmed due to the high background noise associated with the inherent radioactivity of the test specimens. X-ray diffraction analyses of both radioactive and non-radioactive aluminosilicate pellets confirmed the crystal lattice structure to be pollucite. Cesium ion quasistatic leachability measurements determined the leach rates of fully loaded /sup 137/Cs sectioned pollucite pellets to date to be 4.61 to 34.4 x 10/sup -10/ kg m/sup -2/s/sup -1/, while static leach tests performed on unsectioned fully loaded pellets showed the leach rates of the cesium ion to date to be 2.25 to 3.41 x 10/sup -12/ kg m/sup -2/s/sup -1/. The cesium ion diffusion coefficients through the pollucite pellet were calculated using Fick's first and second laws of diffusion. The diffusion coefficients calculated for three tracer level /sup 137/Cs aluminosilicate pellets were 1.29 x 10/sup -16/m/sup 2/s/sup -1/, 6.88 x 10/sup -17/m/sup 2/s/sup -1/, and 1.35 x 10/sup -17/m/sup 2/s/sup -1

  2. Biosorption of cesium by native and chemically modified biomass of marine algae: introduce the new biosorbents for biotechnology applications

    Energy Technology Data Exchange (ETDEWEB)

    Jalali-Rad, R. [Department of Biotechnology, Nuclear Research Center, Atomic Energy Organization of Iran, Tehran (Iran, Islamic Republic of)]. E-mail: rjalali@aeoi.org.ir; Ghafourian, H. [Department of Biotechnology, Nuclear Research Center, Atomic Energy Organization of Iran, Tehran (Iran, Islamic Republic of); Asef, Y. [Department of Biotechnology, Nuclear Research Center, Atomic Energy Organization of Iran, Tehran (Iran, Islamic Republic of); Dalir, S.T. [Department of Biotechnology, Nuclear Research Center, Atomic Energy Organization of Iran, Tehran (Iran, Islamic Republic of); Sahafipour, M.H. [Department of Biotechnology, Nuclear Research Center, Atomic Energy Organization of Iran, Tehran (Iran, Islamic Republic of); Gharanjik, B.M. [Offshore Fisheries Research Center, Chabahar (Iran, Islamic Republic of)

    2004-12-10

    Biosorption batch experiments were conducted to determine the cesium binding ability of native biomass and chemically modified biosorbents derived from marine algae, namely ferrocyanide algal sorbents type 1 and type 2 (FASs1 and FASs2). The applicability of the Langmuir and Freundlich isotherms for representation of the experimental data was investigated. The cesium sorption performances of the various types of sorbents were compared using the maximum capacities (q{sub max} values) obtained from fitting the Langmuir isotherm to the values calculated from the sorption experiments, which FASs type 1 and type 2 showed better sorption performances for cesium. FASs1 and FASs2 derived from formaldehyde and glutaraldehyde crosslinked Padina australis exhibited lower sorption capacities than those prepared from the non-crosslinked one. Most of the cesium ions were bound to FASs1, derived from Sargassum glaucescens and P. australis, in <2 min and equilibrium reached within the first 30 min of contact. Biosorption of cesium by FASs1 derived from P. australis and Cystoseria indica was constantly occurred at a wide range of pH, between 1 and 10, and the highest removal took place at pH 4. The presence of sodium and potassium at 0.5 and 1 mM did not inhibit cesium biosorption by algae biomass. The maximum cesium uptake was acquired using the large particles of FAS2 originated from S. glaucescens (2-4 mm). Desorption of cesium from the metal-laden FASs1 (from P. australis, S. glaucescens and Dictyota indica) was completely achieved applying 0.5 and 1 M NaOH and KOH, although the cesium sorption capacity of the biosorbents (from C. indica and S. glaucescens) decreased by 46-51% after 9 sorption-desorption cycles.

  3. Comparison of thallium-201, Tc-99m MIBI and I-131 scan in the follow-up assessment after I-131 ablative therapy in differentiated thyroid cancer

    Energy Technology Data Exchange (ETDEWEB)

    Kwon, Jae Sung; Lee, Sung Keun; Kim, Doe Min; Park, Sae Jong; Jang, Kyong Sun; Kim, Eun Sil; Kim, Chong Soon [Hanil General Hospital, Seoul (Korea, Republic of)

    1999-08-01

    We conducted a comparative study to evaluate the diagnostic values of Tl-201, Tc-99m MIBI and I-131 scans in the follow-up assessment after ablative I-131 therapy in differentiated thyroid cancer. The study population consisted of 20 patients who underwent surgical removal of thyroid cancer and ablative radioactive iodine therapy, and followed by one or more times of I-131 retreatment (33 cases). In all patients, Tl-201, Tc-99m MIBI, diagnostic and therapeutic I-131 scans were performed and the results were analyzed retrospectively. Also serum thyroglobulin levels were measured in all patients. The final diagnosis of recurrent or metastatic thyroid cancer was determined by clinical, biochemical, radiologic and/or biopsy findings. Positive rates (PR) of Tc-99m MIBI, Tl-201, diagnostic and therapeutic I-131 scans in detecting malignant thyroid tissue lesions were 70% (19/27), 54% (15/28), 35% (17/48) and 63% (30/48), respectively. The PR in the group of 20 cases (28 lesions) who underwent concomitant Tl-201 and I-131 scans were in the order of therapeutic 131 scan 71%, Tl-201 scan 54% and diagnostic I-131 scan 36%. There was no statistically significant difference between Tl-201 and diagnostic I-131 scans (p>0.05). In the group of 20 cases (27 lesions) who underwent concomitant Tc-99m MIBI and I-131 scans, the PR were in the order of Tc-99m MIBI scan 70%, I-131 therapeutic scan 52% and I-131 diagnostic scan 33%. The PR of Tc-99m MIBI was significantly higher than that of diagnostic I-131 scan (p<0.05). Tc-99m MIBI scan is superior to diagnostic I-131 scan in detecting recurrent or metastatic thyroid cancer following ablation therapy in patients with differentiated thyroid cancer. Tl-201 scan did not showed significantly higher positive rate than diagnostic I-131 scan. Instead of diagnostic I-131 scan before the I-131 retreatment, Tc-99m MIBI scan without discontinuing thyroid hormone replacement would be a prudent and effective approach in the management of these

  4. Performance modeling of an integral, self-regulating cesium reservoir for the ATI-TFE

    International Nuclear Information System (INIS)

    This work covers the performance modeling of an integral metal-matrix cesium-graphite reservoir for operation in the Advanced Thermionic Initiative-Thermionic Fuel Element (ATI-TFE) converter configuration. The objectives of this task were to incorporate an intercalated cesium-graphite reservoir for the 3C24Cs→2C36Cs+Cs(g) two phase equilibrium reaction into the emitter lead region of the ATI-TFE. A semi two-dimensional, cylindrical TFE computer model was used to obtain thermal and electrical converter output characteristics for various reservoir locations. The results of this study are distributions for the interelectrode voltage, output current density, and output power density as a function of axial position along the TFE emitter. This analysis was accomplished by identifying an optimum cesium pressure for three representative pins in the ATI ''driverless'' reactor core and determining the corresponding position of the graphite reservoir in the ATI-TFE lead region. The position for placement of the graphite reservoir was determined by performing a first-order heat transfer analysis of the TFE lead region to determine its temperature distribution. The results of this analysis indicate that for the graphite reservoirs investigated the 3C24Cs→2C36Cs+Cs(g) equilibrium reaction reservoir is ideal for placement in the TFE emitter lead region. This reservoir can be directly coupled to the emitter, through conduction, to provide the desired cesium pressure for optimum performance. The cesium pressure corresponding to the optimum converter output performance was found to be 2.18 torr for the ATI core least power TFE, 2.92 torr for the average power TFE, and 4.93 torr for the maximum power TFE

  5. Synthesis of Iron-ferrocyanide functionalized magnetic nanocluster for the removal of cesium

    International Nuclear Information System (INIS)

    In the present study, magnetite nanocluster was synthesized by hydrothermal method, and coated with iron ferrocyanide for the adsorption of cesium in an aqueous solution through simple addition of iron ferrocyanide in acid condition. We describe the morphology, structure, and physical property of these nanoparticles. In addition, their ability to eliminate cesium from water was also evaluated. In this study, we fabricated Iron ferrocyanide immobilized magnetite nanocluster (IFC-MNC) using hydrothermal methods. The CIFC-MNC exhibited easy separation ability from water by an external magnet, and showed a high removal efficiency of cesium in aqueous solutions. Therefore, the IFC-MNC demonstrated good potential for the treatment of water contaminated with radioactive cesium. gnetic nanoadsorbents composed of a magnetic particles core and functional shell, which adsorb the contaminants, has attracted significant attention in environmental remediation owing to their high surface area and unique superparamagnetism. The nuclear accident at the Fukushima Daiichi nuclear power station in 2011 released a huge quantity of radioactive contaminants into the environment. Among these, cesium Cs-137 is the most problematic contaminant due to its long half-life (30.2 years), and high-energy gamma ray (γ-ray) emissions. Among various adsorbents to treat Cs-137 contaminated water, metal ferrocyanides were widely applied to remove the Cs-137 in water. For better separation of metal ferrocyanide from water, recently, our group reported the fabrication of copper ferrocyanide-functionalized magnetic nanoparticles (Cu-FC-EDA-MNPs) using alkoxysilanes, having ethylenediamine (EDA) group, modified Fe3O4 nanoparticles (EDA-MNPs) for the fast and easy magnetic separation of metal ferrocyanide. However, the fabrication method was multistep procedure. Thus, a more simplified fabrication procedure is still desired

  6. An isotope dilution-precipitation process for removing radioactive cesium from wastewater

    Energy Technology Data Exchange (ETDEWEB)

    Rogers, Harold, E-mail: rogers22@llnl.gov [Lawrence Livermore National Laboratory, 7000 East Avenue, Livermore, CA, 94550 (United States); Bowers, John; Gates-Anderson, Dianne [Lawrence Livermore National Laboratory, 7000 East Avenue, Livermore, CA, 94550 (United States)

    2012-12-15

    Highlights: Black-Right-Pointing-Pointer Developed an isotope dilution-precipitation treatment process for Cs-137 contaminated water. Black-Right-Pointing-Pointer Waste seeded with non-radioactive Cs-133 prior to precipitation with sodium tetraphenylborate. Black-Right-Pointing-Pointer Final Cs-137 concentrations below DOE discharge limit of 3.0 Multiplication-Sign 10{sup -6} {mu}Ci/mL can be achieved. Black-Right-Pointing-Pointer Synthetic wastewater, and industrial low level radioactive proof of principle studies completed. - Abstract: A novel isotope dilution-precipitation method has been developed to remove cesium-137 from radioactive wastewater. The process involves adding stable cesium chloride to wastewater in order to raise the total cesium concentration, which then allows both the stable and radioactive cesium ions to be precipitated together using sodium tetraphenylborate. This process was investigated utilizing laboratory solutions to determine stable cesium dose rates, mixing times, effects of pH, and filtration requirements. Once optimized, the process was then tested on synthetic wastewater and aqueous low-level waste. Experiments showed the reaction to be very quick and stable in the pH range tested, 2.5-11.5. The wastewater may need to be filtered using a 0.45-{mu}m filter, though ferric sulfate has been shown to promote coagulation and settling, thereby eliminating the necessity for filtration. This investigation showed that this isotope dilution-precipitation process can remove Cs-37 levels below the U.S. Department of Energy's (DOE) Derived Concentration Standard (DCS) of 3.0 Multiplication-Sign 10{sup -6} {mu}Ci/mL using a single dosage, potentially allowing the wastewater to be discharged directly to sanitary sewers.

  7. Synthesis of Iron-ferrocyanide functionalized magnetic nanocluster for the removal of cesium

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Hee-Man; Jang, Sung-Chan; Lee, Kune Woo; Seo, Bum-Kyoung; Moon, Jei Kwon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-10-15

    In the present study, magnetite nanocluster was synthesized by hydrothermal method, and coated with iron ferrocyanide for the adsorption of cesium in an aqueous solution through simple addition of iron ferrocyanide in acid condition. We describe the morphology, structure, and physical property of these nanoparticles. In addition, their ability to eliminate cesium from water was also evaluated. In this study, we fabricated Iron ferrocyanide immobilized magnetite nanocluster (IFC-MNC) using hydrothermal methods. The CIFC-MNC exhibited easy separation ability from water by an external magnet, and showed a high removal efficiency of cesium in aqueous solutions. Therefore, the IFC-MNC demonstrated good potential for the treatment of water contaminated with radioactive cesium. gnetic nanoadsorbents composed of a magnetic particles core and functional shell, which adsorb the contaminants, has attracted significant attention in environmental remediation owing to their high surface area and unique superparamagnetism. The nuclear accident at the Fukushima Daiichi nuclear power station in 2011 released a huge quantity of radioactive contaminants into the environment. Among these, cesium Cs-137 is the most problematic contaminant due to its long half-life (30.2 years), and high-energy gamma ray (γ-ray) emissions. Among various adsorbents to treat Cs-137 contaminated water, metal ferrocyanides were widely applied to remove the Cs-137 in water. For better separation of metal ferrocyanide from water, recently, our group reported the fabrication of copper ferrocyanide-functionalized magnetic nanoparticles (Cu-FC-EDA-MNPs) using alkoxysilanes, having ethylenediamine (EDA) group, modified Fe{sub 3}O{sub 4} nanoparticles (EDA-MNPs) for the fast and easy magnetic separation of metal ferrocyanide. However, the fabrication method was multistep procedure. Thus, a more simplified fabrication procedure is still desired.

  8. Preparation and use of polymeric materials containing hydrophobic anions and plasticizers for separation of cesium and strontium

    International Nuclear Information System (INIS)

    Preparation and use is described for polymeric materials containing hydrophobic anions and plasticizers for extraction of cesium and strontium. The use of polymeric materials containing plasticizers which are solvents for hydrophobic anions such as derivatives of cobalt dicarbollide or tetraphenylborate which are capable of extracting cesium and strontium ions from aqueous solutions in contact with the polymeric materials, is described. The polymeric material may also include a synergistic agent for a given ion like polyethylene glycol or a crown ether, for removal of radioactive isotopes of cesium and strontium from solutions of diverse composition and, in particular, for solutions containing large excess of sodium nitrate

  9. 27 CFR 28.131 - Application for return of wines withdrawn without payment of tax.

    Science.gov (United States)

    2010-04-01

    ... wines withdrawn without payment of tax. 28.131 Section 28.131 Alcohol, Tobacco Products and Firearms... Withdrawal of Wine Without Payment of Tax for Exportation, Use on Vessels and Aircraft, Transfer to a Foreign... Return of Wines to Bonded Wine Cellar § 28.131 Application for return of wines withdrawn without...

  10. 40 CFR 131.8 - Requirements for Indian Tribes to administer a water quality standards program.

    Science.gov (United States)

    2010-07-01

    ... administer a water quality standards program. 131.8 Section 131.8 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS WATER QUALITY STANDARDS General Provisions § 131.8 Requirements for Indian Tribes to administer a water quality standards program. (a) The Regional Administrator,...

  11. 40 CFR 131.21 - EPA review and approval of water quality standards.

    Science.gov (United States)

    2010-07-01

    ... quality standards. 131.21 Section 131.21 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS WATER QUALITY STANDARDS Procedures for Review and Revision of Water Quality Standards § 131.21 EPA review and approval of water quality standards. (a) After the State submits...

  12. Vocal cord paralysis following I-131 ablation of a postthyroidectomy remnant

    Energy Technology Data Exchange (ETDEWEB)

    Lee, T.C.; Harbert, J.C.; Dejter, S.W.; Mariner, D.R.; VanDam, J.

    1985-01-01

    Vocal cord paralysis has been reported following I-131 therapy of thyrotoxicosis and following ablation of the whole thryoid. However, this rare complication has not previously been described following I-131 ablation of a postthyroidectomy remnant. The authors report a patient who required tracheostomy for bilateral vocal cord paralysis following I-131 ablation after near-total thyroidectomy for papillary thyroid carcinoma.

  13. 13 CFR 120.131 - Leasing part of new construction or existing building to another business.

    Science.gov (United States)

    2010-01-01

    ... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Leasing part of new construction or existing building to another business. 120.131 Section 120.131 Business Credit and Assistance... § 120.131 Leasing part of new construction or existing building to another business. (a) If the...

  14. The clinical significance of measuring the thyroid 131I uptake rate to identify the type of premature hypothyroidism for hyperthyroid after 131I treatment

    International Nuclear Information System (INIS)

    The 3 h thyroid 131I uptake rate and the content of serum TT3, TT4, TSH are measured in 63 patients of premature hypothyroidism (consisting of 33 provisional hypothyroids and 30 perpetual hypothyroidism) before and after thyroxine substitutes treatment for six moths. The results show that there is obvious difference in 131I uptake rate compared provisional hypothyroidism with perpetual hypothyroidism, and no difference in the content of serum TT3, TT4, TSH before the treatment. Compared with normal conditions, there is no difference in 131I uptake rate of provisional hypothyroidism, but the 131I uptake rate of perpetual hypothyroidism has obvious decrease before and after the treatment. Therefore the type of patients who suffer from premature hypothyroidism can be distinguished according to the 131I uptake rate: if the 3 h thyroid 131I uptake rate is normal, it is provisional hypothyroidism; if not, it is perpetual hypothyroidism

  15. Adjuvant radioactive iodine (I131) therapy in patients with papillary thyroid cancer: comparison of ablation outcome post low and high doses of I131

    International Nuclear Information System (INIS)

    Full text of publication follows. Introduction: I131 ablation post total thyroidectomy is a well established adjuvant therapy in patients with papillary thyroid cancer. Many factors can affect ablation outcome including size of remnant thyroid tissue, stage of the disease and given dose of I131. Some authors stated that small doses of I131 can achieve successful complete ablation outcome comparable to high ablative dose. Aim: the aim of the current study is to compare successful complete ablation rate using low I131 ablation dose (30 mCi) versus high dose (100 mCi) post total thyroidectomy in patients with papillary thyroid cancer confined to the thyroid gland. Patients and methods: 129 patients with papillary thyroid cancer confined to the thyroid gland, with no regional lymph nodal or systemic metastases, candidates for I131 ablation therapy post total thyroidectomy, were included in the current study. 61 patients received 30 mCi ablative dose on our patient basis. The remaining 68 patients received high ablation dose (100 mCi). All patients performed follow up I131 whole body scan, neck ultrasound and unsuppressed serum thyroglobulin level (Tg) 6-9 months post I131 therapy. Successful complete ablation was considered in absence of any I131 avid thyroid tissue in the neck, free neck ultrasound and Tg level < 2 ng/ml. Results: successful complete ablation post 30 mCi of I131 was noted in 36 out of 61 patients (59%). On the other hand, this was observed post 100 mCi in 56 out of 68 patients (82.3%), with a statistically significant difference between both groups (p<0.05). Conclusion: in patients with papillary thyroid cancer confined to the thyroid gland, candidates for I131 ablation therapy post total thyroidectomy, high ablation dose of I131 (100 mCi) has significantly higher successful complete ablation rate compared to small I131 dose (30 mCi). (authors)

  16. The success of {sup 131}I ablation in thyroid cancer patients is significantly reduced after a diagnostic activity of 40 MBq {sup 131}I

    Energy Technology Data Exchange (ETDEWEB)

    Verburg, F.A. [Dept. of Nuclear Medicine, Univ. Medical Center Utrecht (Netherlands); Dept. of Nuclear Medicine, Univ. Hospital Wuerzburg (Germany); Verkooijen, R.B.T. [Div. of Nuclear Medicine, Dept. of Radiology, Leiden Univ. Medical Center (Netherlands); Dept. of Nuclear Medicine, Maxima Medical Centre (Netherlands); Stokkel, M.P.M. [Div. of Nuclear Medicine, Dept. of Radiology, Leiden Univ. Medical Center (Netherlands); Isselt, J.W. van [Dept. of Nuclear Medicine, Univ. Medical Center Utrecht (Netherlands)

    2009-07-01

    Objective: Dosimetry studies have shown that activities of {sup 131}I as small as 10-20 MBq may cause a stunning effect. A result of this stunning effect may be a lower success rate of the ablative {sup 131}I therapy for differentiated thyroid carcinoma (DTC). The aim of this study was to determine whether pre-therapeutic uptake measurement with 40 MBq {sup 131}I causes a lower success rate of ablation. Design: retrospective chart review study. Patients, methods: In two hospitals the ablation protocols differed in one respect only: in the one hospital no diagnostic {sup 131}I was applied before ablation (group 1, n = 48), whereas in the other hospital a 24-h uptake-measurement with 40 MBq {sup 131}I was performed (group 2, n = 51). Included were all DTC patients without distant metastases who had undergone {sup 131}I ablation between July 2002 and December 2005, and who had returned for {sup 131}I follow-up. Successful ablation was defined as absence of pathological {sup 131}I uptake on diagnostic whole-body scintigraphy and undetectable thyroglobulin-levels under TSH stimulation. Results: Overall, ablation was successful in 31/48 patients (65%) in group 1 and in 17/51 patients (33%) in group 2 (p=0.002). Multivariate analysis showed that pre-therapeutic uptake measurement using 40 MBq {sup 131}I was an independant determinant for success of ablation (p = 0.002). Conclusions: After applying a diagnostic activity of 40 MBq {sup 131}I before ablation, the success rate of ablation is severely reduced. Consequently, the routine application of {sup 131}I for diagnostic scintigraphy or uptake measurement prior to {sup 131}I ablation is best avoided. (orig.)

  17. Comparison of 131I-TYR3-octreotate and 131I-DOTA-TYR3-octreotate: The effect of DOTA on pharmacokinetics and stability

    International Nuclear Information System (INIS)

    The authors compared the biodistribution, and in vivo and in vitro stabilities of 131I-Tyr3-octreotate and 131I-DOTA-Tyr3-octreotate. The peptides were radioiodinated by the chloramine T method and high radiochemical yields were obtained (greater than 97%). Both labelled compounds showed high stability when incubated in human plasma at 37 deg C. The 131I-Tyr3-octreotate showed significant hepatic uptake and biliary excretion. The biodistribution of 131I-DOTA-Tyr3-octreotate, however, can be compared with the distribution of radiometal labelled octreotide analogues. (author)

  18. 131I metabolism in the study of antithyroid drug

    International Nuclear Information System (INIS)

    The main purpose of the present report was to study the action of antithyroid drugs on different parameters of thyroid activity utilizing 131I, in the offsprings of rats treated during pregnancy and the perinatal period. Both PTU and MMI caused alterations in growth and thyroid activity, but they were more dramatic with the former. A significative increase in 131I thyroid uptake and in circulating radioactivity was observed. When % uptake was expressed as a function of thyroidal and body weights, a significative decrease was noticed. The ratio T/S and the percentage of labelled iodothyronines in pancreatin digests were also decreased. Neuromuscular maturation was evaluated, by means of the test of Schapiro. A group of animals treated with PTU plus T4 had a significant delay, reaching normal developement later than the controls or those treated with MMI. (author)

  19. Hypothyroidism caused by 131I treatment for Graves disease

    International Nuclear Information System (INIS)

    The refollow-up has been carried out in hypothyroidism caused by 131I treatment for Graves disease. The serum HS-TSH(IRMA), FT3, TSH(RIA), TT3, TT4, FT4I, MCA, TGA, Cholesterol and Triglyceride has been measured in 26 patient after 131I treatment for 9.5 years in average. At the same time TRH stimulation test was also performed, and the clinical symptoms and signs assessed. The results showed that TSH is the most sensitive criterion for hypothyroidism, followed by Cholesterol and FT4I. The occurence of hypothyroidism may be related to the presence of thyroid antibody as demonstrated by the elevation of serum MCA, TGA. Therefore measurement of serum TSH, FT4I and Cholesterol during long term follow-up is beneficial for early diagnosis of hypothyroidism and evaluating the effect of substitution treatment

  20. Iodine-131 releases from the Hanford Site, 1944--1947

    International Nuclear Information System (INIS)

    Releases of fission product iodine-131 are calculated for the 1944 through 1947 period from the Hanford Reservation. Releases to the atmosphere were from the ventilation stacks of T and B separation plants. A reconstruction of daily separation plant operations forms the basis of the releases. The reconstruction traces the iodine-131 content of each fuel discharge from the B, D, and F Reactors to the dissolving step in the separation plants. Statistical computer modeling techniques are used to estimate hourly release histories based on sampling mathematical distribution functions that express the uncertainties in the source data and timing. The reported daily, monthly, and yearly estimates are averages and uncertainty ranges are based on 100 independent Monte Carlo ''realizations'' of the hourly release histories

  1. Nuclear and health news. iodine 131 Fleurus incident - Belgium

    International Nuclear Information System (INIS)

    On the 25. august 2008, the operator of the institute of radioelements in belgium has informed the federal agency of nuclear control of an abnormal release of iodine 131 by the chimney of the building to environment. This release occurred following a transfer of liquid effluents between tanks. This release lasts several days and the activity released has been estimated to 45 Giga-becquerels. The incident was classified at the level 3 on the INES scale. The production of radioelements was stopped and the consumption of fruits and vegetables from gardens as well as the rainwater was forbidden at five kilometers at the north-east of the installation. On the 30. august analysis were made on grass and milk but no detection of iodine 131 appears. (N.C.)

  2. High spin spectroscopy in 130,131Ba

    International Nuclear Information System (INIS)

    The high spin states in 130,131Ba has been populated in the fusion evaporation reaction 122Sn(13C,4n)130,131Ba at Ebeam = 65 MeV. The experiment was carried out at the 14-UD pelletron accelerator at IUAC, New Delhi, India, which delivered 13C beam on a ∼ 1.0 mg/cm2 thick 122Sn target with Au (6.7 mg/cm2) backing. The γ decay following the reaction was studied using an array consisting of fifteen Compton suppressed clover detectors of INGA (Indian National Gamma Array) placed at angle of 32°(3-covers), 57°(2-clovers), 90°(4-clovers), 123°(2-clovers), 148°(4-clovers) with respect to the beam direction. The data were collected when two or more clover fired. Data have been analyzed using software CANDLE, INGASORT and RADWARE. Symmetric and Asymmetric matrices have been constructed using 2-fold as well as 3-fold data. Cube has also been made for 3-fold data. The γ transitions belonging to various band structure were detected using an array of fifteen Clover Germanium detector. In extension to earlier work done by R. Ma et al to study 131 Ba and D. Bazzacco et al. to study 130 Ba some of new transitions has been placed in high spin states. A few transitions connecting two negative parity bands in 130Ba has been established. Spin and parity for a band has been calculated for first time in 131Ba. The said band is interpreted in term of multi-quasiparticle configuration, based on Total Routhian Surface (TRS) calculation (author)

  3. Preparation and stability of 131I-tetracycline

    International Nuclear Information System (INIS)

    A method for the iodination of tetracycline is presented which yields > 85% labeling efficiency. The product is stable for a minimum of 72 hr and appears to retain tetracycline-like properties when studied in vivo. The critical factors in the synthesis are reaction temperature, acidity, and drying temperature. The data suggest that 131I-TET can be studied as a tumor scanning agent without fear of product artifact. (author)

  4. Iodine 131 therapy patients: radiation dose to staff

    International Nuclear Information System (INIS)

    Metastasis to the skeletal system from follicular thyroid carcinoma may be treated with an oral dose of 131I-NaI. Radiation exposures to hospital personnel attending these patients were calculated as a function of administered dose, distance from the patient and time after administration. Routine or emergency patient handling tasks would not exceed occupational radiation protection guidelines for up to 30 min immediately after administration. The emergency handling of several patients presents the potential for exceeding these guidelines. (author)

  5. Hypertension complicating 131I-meta-iodobenzylguanidine therapy for neuroblastoma

    International Nuclear Information System (INIS)

    Radiolabelled meta-iodobenzylguanidine (mIBG), used as targeted therapy for neuroblastoma, is known to have effects on blood pressure (BP). In this study we audited BP changes in patients receiving 131I-mIBG therapy for neuroblastoma to identify BP-related adverse events (AE) and possible predictive factors. Between 2003 and 2010, 50 patients with neuroblastoma received 110 131I-mIBG administrations. BP measurements before and after administration were compared with age- and sex-matched centile values. AE were analysed, and possible predisposing factors identified. This population had a baseline BP distribution higher than that of their age- and sex-matched peers, with 16% of preadministration systolic BP values above the 95th centile. Changes in BP after administration showed an approximately normal distribution with similar numbers of reduced and increased values. Four AE, all related to hypertension, occurred with one patient having generalized seizures. One AE was immediate, others occurred between 20 and 25 h after administration. No significant association between AE and patient age or sex was demonstrated. However, a significant association between AE and high preadministration BP was shown, both above the 90th centile (p = 0.0022) and above the 95th centile (p = 0.0135). Clinically relevant hypertension following 131I-mIBG therapy affected less than 5% of administrations, but was more common in those patients with preexisting hypertension. As hypertensive episodes may occur many hours after treatment, close monitoring of BP needs to be continued for at least 48 h after administration of 131I-mIBG. (orig.)

  6. 131I-m IBG preparation and clinical applications

    International Nuclear Information System (INIS)

    The factors affecting the preparation of 131I-mIBG were studied and the optimal labelling and preparation conditions were determined in a manner that the requirements of GRP and GMP are satisfied. The m-IBG was labeled by isotopic exchange method where in situ produced Cu (II) was used as a catalyst. The Cu (II) was in situ produced by the effect of thiosulfate on Cu(II) ions in the presence of acetic acid. The optimal conditions were determined as: (The ratio of acetic acid to the iodide-131 solution is 0.5-1.5, the reaction temperature is (160 Centigrade), the reaction period is 60 minutes, and the quantity of m-IBG must be more than 1mg). At these conditions, high labelling yield of 98% was obtained. Further purification lead to an increase in the RCP to more than 99%. All preparations produced sterile and Pyrogen free solutions. The biodistribution studies in rats showed random distribution, which were slightly higher than that were shown in literature. These differences were attributed to the absence of stable iodine saturation of the rats prior to the injection of 131I-mIBG in this study. Clinical studies using our products showed high localization in the tumors in case of neuroblastoma patients and in adrenal gland in case of pheochromocytoma patients. (author)

  7. Does I-131-MIBG underestimate skeletal disease burden in neuroblastoma?

    Directory of Open Access Journals (Sweden)

    Barai Sukanta

    2004-10-01

    Full Text Available Background: Controversy persists as to the need for both MIBG and bone scanning in routine evaluation of neuroblastoma. Aim: To compare the efficacy of I-131- metaiodobenzylguanidine (MIBG scan against that of conventional Tc99m- methylene diphosphonate (MDP bone scan for the detection of skeletal deposition of neuroblastoma. Methods and Material: The study included 57 patients (36 boys, 21 girls: age range 1-14 years of neuroblastoma who underwent both bone scan with Tc99m-MDP and I-131-MIBG scan within 15 days of each other at presentation and during follow-up. Results: At presentation 11(19.2% patients had evidence of skeletal metastases on MDP scan against 7 patients who showed bony secondaries on MIBG scan. Of the 7 patients, with positive MIBG and MDP scans, MDP scan detected 11 sites whereas MIBG scan detected 7 sites. On follow-up study, 3 patients with initial abnormal MDP scan but normal MIBG scan, developed skeletal metastases detectable on MIBG scan, whereas 3 of the 46 patients who had normal MDP and MIBG scan at presentation; developed skeletal metastases detectable on MDP scan. MIBG scan was concordant in 2 of them but was normal in the third patient. Conclusion: I-131-MIBG underestimates skeletal disease burden in neuroblastoma. Therefore, Tc99m-MDP bone scan should remain a part of routine assessment of patients with neuroblastoma.

  8. Removal of cesium using coconut fiber in raw and modified forms for the treatment of radioactive liquid wastes

    Energy Technology Data Exchange (ETDEWEB)

    Jesus, Nella N.M. de; Nobre, Vanessa B.; Potiens Junior, Ademar J.; Sakata, Solange K., E-mail: sksakata@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Di Vitta, Patricia B. [Universidade de Sao Paulo (USP), SP (Brazil). Instituto de Quimica

    2013-07-01

    Sorption is one of the most studied methods to reduce the volume of radioactive waste streams. Cesium-137 is a radioisotope formed by the fission of uranium and it can cause health problems due to its easy assimilation by cells. The aim of this study is to evaluate the potential of coconut fiber in removing cesium from radioactive liquid wastes; this process can help in disposing radioactive waste. The experiments were performed in batch and the particle size of the fiber ranged between 0.30 mm and 0.50 mm. The fiber was treated with hydrogen peroxide in alkaline medium. The following parameters were analyzed: contact time, pH and concentration of cesium ions in aqueous solution. After the experiments the samples were filtered and cesium remaining in solution was quantified by inductively coupled plasma optical emission spectrometry. (author)

  9. Frequency doubling with periodically poled KTiOPO4 at the fundamental wave of cesium D2 transition

    Institute of Scientific and Technical Information of China (English)

    Xiaoling Song; Zhigang Li; Pengfei Zhang; Gang Li; Yuchi Zhang; Junmin Wang; Tiancai Zhang

    2007-01-01

    @@ We report the continuous wave (CW) second harmonic generation (SHG) with a periodically poled KTiOPO4 (PPKTP) pumped by a diode laser at 852.356 nm, which is exactly resonant on the cesium D2 transition.

  10. Application of a composite sorbent based om natural and synthetic zeolites for cesium ion elimination from water solutions

    International Nuclear Information System (INIS)

    The study has been carried out to determine the effect of variations in the content of natural and synthetic zeolites, being the components of the composite sorbent, on the cesium sorption from the water solution

  11. Spin-dependent asymmetry functions in the elastic and inelastic electron-cesium scattering at intermediate energies

    International Nuclear Information System (INIS)

    In this thesis the measurements of the relative differential cross section, the exchange asymmetry, the spin-orbit asymmetry, and the interference asymmetry for the electron scattering on cesium atoms from 4 to 18 eV is described. (HSI)

  12. Cesium-137 in ash from combustion of biofuels. Application of regulations from the Swedish Radiation Safety Authority; Cesium-137 i aska fraan foerbraenning av biobraenslen. Tillaempning av Straalsaekerhetsmyndighetens regler

    Energy Technology Data Exchange (ETDEWEB)

    Sjoeblom, Rolf (Tekedo AB, Nykoeping (SE))

    2009-03-19

    The Swedish Radiation Safety Authority, SSM, has issued an ordinance on ash contaminated with Cesium-137. It implies amongst other things that ash containing 0,5 - 10 kBq/kg Cesium-137 (so-called contaminated ash) can be used for geotechnical purposes provided that the content in a near-by well does not exceed 1 Bq/litre and that the increase in a near-by fish producing recipient does not exceed 0,1 Bq/litre. The initial plan with the presently reported work was to provide a compilation of how the ordinance for Cesium-137 can be applied in practical work. It became evident, however, in the course of the work that issues related to the co-variation between potassium and Cesium needed further investigation. As a result, the present report comprises also a compilation of this extended information search. Cesium-137 is present in ash as a result of the accident in a nuclear power reactor in Chernobyl in 1986 during which material having a very small grain size was spread to a high altitude. A few days later, Cesium-137 was deposited during rains over large parts of Sweden. This activity penetrated to a depth of one or a few decimetres during the course of the subsequent few days and weeks, after which it was partially taken up by plants and spread in the ecosystem. Section 2 has the character of a handbook. It provides basic information on radiation, and also about the ordinance and other material from the SSI. Section 3 comprises compilations of relevant international status of knowledge. This regards how potassium and Cesium behave in soil and ash, and also how spreading of Cesium can be modelled. Cesium behaves similarly to Potassium but with the difference that Cesium is bonded much more strongly to mineral soil and ash. Potassium and Cesium appears in soil in four different forms: dissolved in the pore water, exchangeable, non-exchangeable and as bonded to minerals. The amount dissolved in the pore water is the smallest and that bonded to minerals is the largest

  13. The promotional effects of cesium promoter on higher alcohol synthesis from syngas over cesium-promoted Cu/ZnO/Al2O3 catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Jie; Cai, Qiuxia; Wan, Yan; Wan, Shaolong; Wang, Li; Lin, Jingdong; Mei, Donghai; Wang, Yong

    2016-09-02

    In this study, the promotional effects of cesium promoter on higher alcohol (C2+OH) synthesis from syngas over Cs-Cu/ZnO/Al2O3 catalysts were investigated using a combined experimental and theoretical density functional theory (DFT) calculation method. In the presence of cesium, the C2+OH productivity increases from 77.1 g•kgcat-1•h-1 to 157.3 g•kgcat-1•h-1 at 583 K due to the enhancement of the initial C–C bond formation. Detailed analysis of chain growth probabilities (CGPs) confirms that initial C–C bond formation is the rate-determining step in the temperature range of 543-583 K. Addition of cesium promoter significantly increases the productivities of 2-methyl-1-propanol, while the CGPs values (C3* to 2-methyl-C3*) is almost unaffected. With the assistance of cesium promoter, the CGPs of the initial C–C bond formation step (C1* to C2*) could be increased from 0.13 to 0.25 at 583 K. DFT calculations indicate that the initial C–C bond formation is mainly contributed by the HCO+HCO coupling reaction over the ZnCu(211) model surface. In the presence of the Cs2O, the stabilities of key reaction intermediates such as HCO and H2CO are enhanced which facilitates both HCO+HCO and HCO+H2CO coupling reaction steps with lower activation barriers over the Cs2O-ZnCu(211) surface. The promotional effects of cesium on the C2+OH productivity are also benefited from the competitive CH+HCO coupling reaction over CH hydrogenation that leads to lower alkane formation. In addition, Bader charge analysis suggests that the presence of cesium ions would facilitate the nucleophilic reaction between HCO and H2CO for initial C–C bond formation. This work was supported by the National Natural Science Foundation of China (No. 91545114 and No. 91545203). We appreciate the joint PhD scholarship support from the China Scholarship Council. The authors would also like to thank the support from Collaborative Innovation Center of Chemistry for Energy Materials (2011-iChEM). DM

  14. Hiatal hernia uptake of iodine-131 mimicking mediastinal metastasis of papillary thyroid carcinoma

    International Nuclear Information System (INIS)

    There are a few case reports of hiatal hernia demonstrating thoracic uptake on I-131 scintigraphy. In this case, high thyroglobulin levels in combination with misinterpretation of I-131 uptake in the mediastinum, leaded to mismanagement of the patient. Here we present a case of focal I-131 uptake within a hiatal hernia initially mimicking an isolated mediastinal metastasis. There are many potential causes of false-positive I-131 scan result. In this case, adjunctive chest computed tomography and gastroesophageal barium study helped to elucidate the true nature of this I-131 uptake. False-positive findings may be caused by a wide variety of nonthyroidal carcinomas, which can concentrate radioiodine or from skin contamination. Several organs, such as the gastric, salivary glands, renal cyst, pericardial effusion, and ovarian can accumulate I-131. It should be borne in mind as a potential source of false-positive whole-body I-131 imaging

  15. Sugar-metal ion interactions: the complicated coordination structures of cesium ion with D-ribose and myo-inositol.

    Science.gov (United States)

    Hu, Haijian; Xue, Junhui; Wen, Xiaodong; Li, Weihong; Zhang, Chao; Yang, Limin; Xu, Yizhuang; Zhao, Guozhong; Bu, Xiaoxia; Liu, Kexin; Chen, Jia'er; Wu, Jinguang

    2013-11-18

    The novel cesium chloride-D-ribose complex (CsCl·C5H10O5; Cs-R) and cesium chloride-myo-inositol complex (CsCl·C6H12O6; Cs-I) have been synthesized and characterized using X-ray diffraction and FTIR, FIR, THz, and Raman spectroscopy. Cs(+) is eight-coordinated to three chloride ions, O1 and O2 from one D-ribose molecule, O1 from another D-ribose molecule, and O4 and O5 from the third D-ribose molecule in Cs-R. For one D-ribose molecule, the oxygen atom O1 in the ring is coordinated to two cesium ions as an oxygen bridge, O2 is cocoordinated with O1 to one of the two cesium ions, and O4 and O5 are coordinated to the third cesium ion, respectively. O3 does not coordinate to metal ions and only takes part in forming hydrogen bonds. One chloride ion is connected to three cesium ions. Thus, a complicated structure of Cs-D-ribose forms. For Cs-I, Cs(+) is 10-coordinated to three chloride ions, O1 and O2 from one myo-inositol molecule, O3 and O4 from another myo-inositol molecule, O5 and O6 from the third myo-inositol molecule, and O6 from the fourth myo-inositol molecule. One metal ion is connected to four ligands, and one myo-inositol is coordinated to four Cs(+) ions, which is also a complicated coordination structure. Crystal structure results, FTIR, FIR, THz, and Raman spectra provide detailed information on the structure and coordination of hydroxyl groups to metal ions in the cesium chloride-D-ribose and cesium chloride-myo-inositol complexes.

  16. Toxicity of upfront {sup 131}I-metaiodobenzylguanidine ({sup 131}I-MIBG) therapy in newly diagnosed neuroblastoma patients: a retrospective analysis

    Energy Technology Data Exchange (ETDEWEB)

    Bleeker, Gitta; Schoot, Reineke A.; Caron, Huib N.; Kraker, Jan de; Tytgat, Godelieve A. [Emma Children' s Hospital, Academic Medical Centre (AMC), Department of Paediatric Oncology, PO Box 22700, Amsterdam (Netherlands); Hoefnagel, Cees A. [National Cancer Institute (NKI-AvL), Department of Nuclear Medicine, Amsterdam (Netherlands); Eck, Berthe L. van [Academic Medical Centre (AMC), Department of Nuclear Medicine, Amsterdam (Netherlands)

    2013-10-15

    In the treatment of patients with high-risk neuroblastoma, different doses of {sup 131}I-metaiodobenzylguanidine ({sup 131}I-MIBG) are administered at different time points during treatment. Toxicity, mainly haematological (thrombocytopenia), from {sup 131}I-MIBG therapy is known to occur in extensively chemotherapy pretreated neuroblastoma patients. Up to now, acute toxicity from {sup 131}I-MIBG as initial treatment has never been studied in a large cohort. The aim of this retrospective study was to document acute toxicity related to upfront {sup 131}I-MIBG. All neuroblastoma patients (stages 1-4 and 4S) treated upfront with {sup 131}I-MIBG at the Emma Children's Hospital, Academic Medical Centre (1992 - 2008) were included in this retrospective analysis. The acute toxicity (during therapy) and short-term toxicity (1st month following therapy) of the first two {sup 131}I-MIBG therapies were studied. Of 66 patients (34 boys, 32 girls; median age 2.2 years, range 0.1 - 9.4 years), 49 had stage 4 disease, 5 stage 4S, 6 stage 3, 1 stage 2 and 5 stage 1. The median first dose was 441 MBq/kg (range 157 - 804 MBq/kg). The median second dose was 328 MBq/kg (range 113 - 727 MBq/kg). The most frequently observed symptoms were nausea and vomiting (21 %, maximum grade II). The main toxicity was grade IV haematological, occurring only in stage 4 patients, after the first and second {sup 131}I-MIBG therapies: anaemia (5 % and 4 %, respectively), leucocytopenia (3 % and 4 %) and thrombocytopenia (2 % and 4 %). No stem cell rescue was needed. The main acute toxicity observed was haematological followed by nausea and vomiting. One patient developed posterior reversible encephalopathy syndrome during {sup 131}I-MIBG therapy, possibly related to {sup 131}I-MIBG. We consider {sup 131}I-MIBG therapy to be a safe treatment modality. (orig.)

  17. Interventional therapy for human breast cancer in nude mice with 131I gelatin microspheres (131I-GMSs) following intratumoral injection

    International Nuclear Information System (INIS)

    The aim of this study was to investigate the effects of 131I gelatin microspheres (131I-GMS) on human breast cancer cells (MCF-7) in nude mice and the biodistribution of 131I-GMSs following intratumoral injections. A total of 20 tumor-bearing mice were divided into a treatment group and control group and received intratumoral injections of 2.5 mci 131I-GMSs and nonradioactive GMSs, respectively. Tumor size was measured once per week. Another 16 mice received intratumoral injections of 0.4 mci 131I-GMSs and were subjected to single photon emission computed tomography (SPECT) scans and tissue radioactivity concentration measurements on day 1, 4, 8 and 16 postinjection. The 20 tumor-bearing mice received intratumoral injections of 0.4 mci [131I] sodium iodide solution and were subjected to SPECT scans and intratumoral radioactivity measurements at 1, 6, 24, 48 and 72 h postinjection. The tumors were collected for histological examination. The average tumor volume in the 131I-GMSs group on post-treatment day 21 decreased to 86.82 ± 63.6%, while it increased to 893.37 ± 158.12% in the control group (P < 0.01 vs. the 131I-GMSs group). 131I-GMSs provided much higher intratumoral retention of radioactivity, resulting in 19.93 ± 5.24% of the injected radioactivity after 16 days, whereas the control group retained only 1.83 ± 0.46% of the injected radioactivity within the tumors at 1 h postinjection. 131I-GMSs suppressed the growth of MCF-7 in nude mice and provided sustained intratumoral radioactivity retention. The results suggest the potential of 131I-GMSs for clinical applications in radiotherapy for breast cancer

  18. 分化型甲状腺癌的131I消融治疗

    Institute of Scientific and Technical Information of China (English)

    关海霞; 陆汉魁

    2012-01-01

    1946年,放射性碘-131 (radioactive iodine-131,RAI,131I)首次被报道用于治疗分化型甲状腺癌(differentiated thyroid cancer,DTC).经过60多年的发展,131I治疗已成为DTC术后处理的重要手段[1].国内最早应用131I治疗DTC约在上世纪60年代.近年来,随着国内DTC病人逐渐增多,131I消融的临床应用也趋于普及化.131I消融包含两个层次:一是采用131I消除和融解DTC术后残留的甲状腺组织,简称131I清甲;二是采用131I消除和融解手术不能切除的DTC转移灶.131I作用机制在于多数DTC细胞(包括DTC原发灶和转移灶)保留正常甲状腺滤泡细胞摄取和存储碘离子的功能.进入体循环的131I被正常甲状腺细胞和DTC细胞摄取和存储后,释放出中能级的β射线粒子,形成细胞内直接电离辐射损伤效应以及对周围相邻细胞有限的交火效应,导致正常甲状腺滤泡细胞和DTC细胞的裂解和凋亡.131I同时释放出高能γ射线穿透人体,可被体外γ相机探测并成像形成131I全身扫描(131I whole body scan,131I-WBS)图,从131I-WBS图可判断术后残留甲状腺组织及DTC转移灶摄取和存储131I的实际情况以及131I在全身其他脏器的实时分布.

  19. Next Generation Extractants for Cesium Separation from High-Level Waste: From Fundamental Concepts to Site Implementation

    Energy Technology Data Exchange (ETDEWEB)

    Moyer, Bruce A; Bazelaire, Eve; Bonnesen, Peter V; Custelcean, Radu; Delmau, Laetitia H; Ditto, Mary E; Engle, Nancy L; Gorbunova, Maryna G; Haverlock, Tamara J; Levitskaia, Taiana G; Bartsch, Richard A; Surowiec, Malgorzata A; Zhou, Hui

    2005-07-06

    This project unites expertise at Oak Ridge National Laboratory (ORNL) and Texas Tech University (TTU, Prof. Richard A. Bartsch) to answer fundamental questions addressing the problem of cesium removal from high-level tank waste. Efforts focus on novel solvent-extraction systems containing calixcrown extractants designed for enhanced cesium binding and release. Exciting results are being obtained in three areas: (1) a new lipophilic cesium extractant with a high solubility in the solvent; (2) new proton-ionizable calixcrowns that both strongly extract cesium and "switch off" when protonated; and (3) an improved solvent system that may be stripped with more than 100-fold greater efficiency. Scientific questions primarily concern how to more effectively reverse extraction, focusing on the use of amino groups and proton-ionizable groups to enable pH-switching. Synthesis is being performed at ORNL (amino calixcrowns) and TTU (proton-ionizable calixcrowns). At ORNL, the extraction behavior is being surveyed to assess the effectiveness of candidate solvent systems, and systematic distribution measurements are under way to obtain a thermodynamic understanding of partitioning and complexation equilibria. Crystal structures obtained at ORNL are revealing the structural details of cesium binding. The overall objective is a significant advance in the predictability and efficiency of cesium extraction from high-level waste in support of potential implementation at U. S. Department of Energy (USDOE) sites.

  20. Next Generation Extractants for Cesium Separation from High-Level Waste: From Fundamental Concepts to Site Implementation

    Energy Technology Data Exchange (ETDEWEB)

    Moyer, Bruce A.; Bazelaire, Eve; Bonnesen, Peter V.; Custelcean, Radu; Delmau, Laetitia H.; Ditto, Mary E.; Engle, Nancy L.; Gorbunova, Maryna G.; Haverlock, Tamara J.; Levitskaia, Tatiana G.; Bartsch, Richard A.; Surowiec, Malgorzata A.; Zhou, Hui

    2005-07-06

    This project unites expertise at Oak Ridge National Laboratory (ORNL) and Texas Tech University (TTU, Prof. Richard A. Bartsch) to answer fundamental questions addressing the problem of cesium removal from high-level tank waste. Efforts focus on novel solvent-extraction systems containing calixcrown extractants designed for enhanced cesium binding and release. Exciting results are being obtained in three areas: (1) a new lipophilic cesium extractant with a high solubility in the solvent; (2) new proton-ionizable calixcrowns that both strongly extract cesium and ''switch off'' when protonated; and (3) an improved solvent system that may be stripped with more than 100-fold greater efficiency. Scientific questions primarily concern how to more effectively reverse extraction, focusing on the use of amino groups and proton-ionizable groups to enable pH-switching. Synthesis is being performed at ORNL (amino calixcrowns) and TTU (proton-ionizable calixcrowns). At ORNL, the extraction behavior is being surveyed to assess the effectiveness of candidate solvent systems, and systematic distribution measurements are under way to obtain a thermodynamic understanding of partitioning and complexation equilibria. Crystal structures obtained at ORNL are revealing the structural details of cesium binding. The overall objective is a significant advance in the predictability and efficiency of cesium extraction from high-level waste in support of potential implementation at U. S. Department of Energy (USDOE) sites.

  1. Experiments and simulations for the dynamics of cesium in negative hydrogen ion sources for ITER N-NBI

    Energy Technology Data Exchange (ETDEWEB)

    Gutser, Raphael

    2010-07-21

    The injection of fast neutral particles (NBI) into a fusion plasma is an important method for plasma heating and current drive. A source for negative deuterium ions delivering an 1 MeV beam that is accelerated to a specific energy and neutralized by a gas target is required for the ITER-NBI. Cesium seeding is required to extract high negative ion current densities from these sources. The optimization of the cesium homogeneity and control are major objectives to achieve the source requirements imposed by ITER. Within the scope of this thesis, the Monte Carlo based numerical transport simulation CsFlow3D was developed, which is the first computer model that is capable of simulating the flux and the accumulation of cesium on the surfaces of negative-ion sources. Basic studies that support the code development were performed at a dedicated experiment at the University of Augsburg. Input parameters of the ad- and desorption of cesium at ion source relevant conditions were taken from systematic measurements with a quartz micro balance, while the injection rate of the cesium oven at the ion source was determined by surface ionization detection. This experimental setup was used for further investigations of the work function of cesium-coated samples during plasma exposure. (orig.)

  2. Experiments and simulations for the dynamics of cesium in negative hydrogen ion sources for ITER N-NBI

    International Nuclear Information System (INIS)

    The injection of fast neutral particles (NBI) into a fusion plasma is an important method for plasma heating and current drive. A source for negative deuterium ions delivering an 1 MeV beam that is accelerated to a specific energy and neutralized by a gas target is required for the ITER-NBI. Cesium seeding is required to extract high negative ion current densities from these sources. The optimization of the cesium homogeneity and control are major objectives to achieve the source requirements imposed by ITER. Within the scope of this thesis, the Monte Carlo based numerical transport simulation CsFlow3D was developed, which is the first computer model that is capable of simulating the flux and the accumulation of cesium on the surfaces of negative-ion sources. Basic studies that support the code development were performed at a dedicated experiment at the University of Augsburg. Input parameters of the ad- and desorption of cesium at ion source relevant conditions were taken from systematic measurements with a quartz micro balance, while the injection rate of the cesium oven at the ion source was determined by surface ionization detection. This experimental setup was used for further investigations of the work function of cesium-coated samples during plasma exposure. (orig.)

  3. Oceanic dispersion of radioactive cesium in the western North Pacific - Eastward dispersion in surface water and southward intrusion with mode water

    Energy Technology Data Exchange (ETDEWEB)

    Kaeriyama, Hideki; Ambe, Daisuke; Shigenobu, Yuya; Fujimoto, Ken; Ono, Tsuneo; Watanabe, Tomowo [National Research Institute of Fisheries Science, Fisheries Research Agency, 2-12-4, Fukuura, Kanazawa, Yokohama, Kanagawa 236-8648 (Japan); Morita, Takami [Fisheries Research Agency, 2-3-3, Minato Mirai, Nishi-ku, Yokohama, Kanagawa 220-6115 (Japan)

    2014-07-01

    The Fukushima Dai-ichi Nuclear Power Plant (FNPP) accident after the Great East Japan Earthquake and tsunami on 11 March 2011 resulted in elevation of the level of anthropogenic radioactivity in the marine environment in the western North Pacific from atmospheric fallout and direct discharges of highly radioactive liquid waters. Intensive monitoring on iodine-131, cesium-134 (Cs-134) and cesium-137 (Cs-137) in seawater near offshore FNPP, and those in marine organisms in the broad area around Japan were conducted, while the information of radioactive contamination in the North Pacific is still limited due to the limitation of the observational data. In this study, we report the concentrations of Cs-134 and Cs-137 in seawater collected from western North Pacific during June 2011 and November 2012. The eastward dispersion of FNPP-derived radioactive cesium in the surface water has been observed with prevention of southward dispersion due to the strong eastward current (Kuroshio Extension; KE) in the North Pacific. Although the concentrations of Cs-134 and Cs-137 were remarkably decreased between 2011 and 2012 at 145 deg. E and 155 deg. E, they were almost comparable between these two years at 175 deg. E. The inventories of Cs-137 between 0-500 m around KE at 147 deg. E were ranged from 3800 to 11000 Bq/m{sup 2} in October 2011, and from 1000 to 2400 Bq/m{sup 2} in November 2012. Surface water had the highest concentration of radioactive Cs at northern part of KE, subsurface peak of radioactive Cs were observed at KE and south of KE in both years. Furthermore, the southward dispersion of FNPP-derived radioactive Cs in the subsurface waters were also observed south of Japan Islands. We found the FNPP-derived Cs-134 (1.8-6.8 mBq/kg) at southernmost 18 deg. N, 135 deg. deg. E in September 2012. The potential density at the subsurface peaks of Cs-134 and increase of water column inventories of Cs-137 after the winter season of 2011-2012, suggested that the main water mass

  4. Discordant imaging of a thyroid nodule with /sup 131/I and /sup 99m/Tc: concordance of /sup 131/I and fluorescent scans

    Energy Technology Data Exchange (ETDEWEB)

    Thrall, J.H.; Burman, K.D.; Wartofsky, L.; Corcoran, R.J.; Johnson, M.C.; Gillin, M.T.

    1978-09-01

    A thyroid nodule, hot by /sup 99m/Tc and cold by /sup 131/I scanning, was reimaged with a fluorescent scanner. The fluorescent scan was qualitatively similar to the /sup 131/I scan and demonstrated low iodine content in the nodule. This combination of scan patterns is compatible with an organification defect in the nodular tissue.

  5. The beta strength function structure in \\beta + decay of lutecium, thulium and cesium isotopes

    CERN Document Server

    Alkhazov, G D; Naumov, Yu V; Orlov, S Yu; Vitman, V D

    1981-01-01

    The spectra of total gamma -absorption in the decays of some lutetium, thulium and cesium isotopes have been measured. The probabilities for level population in the decay of the isotopes have been determined. The deduced beta strength functions reveal pronounced structure. Calculations of the strength functions using the Saxon-Woods potential and the residual Gamow-Teller interaction are presented. It is shown that in beta /sup +/ decay of light thulium and cesium isotopes the strength function comprises more than 70% of the Gamow-Teller excitations with mu /sub tau /=+1. This result is the first direct observation of the Gamov-Teller resonance in beta /sup +/ decay of nuclei with T/sub z/>0. (21 refs).

  6. Light storage via coherent population oscillation in a thermal cesium vapor

    CERN Document Server

    de Almeida, A J F; Maynard, M -A; Laupretre, T; Bretenaker, F; Felinto, D; Goldfarb, F; Tabosa, J W R

    2014-01-01

    We report on the storage of light via the phenomenon of Coherent Population Oscillation (CPO) in an atomic cesium vapor at room temperature. In the experiment the optical information of a probe field is stored in the CPO of two ground states of a Lambda three-level system formed by the Zeeman sublevels of the hyperfine transition F = 3 - F' = 2 of cesium D2 line. We show directly that this CPO based memory is very insensitive to stray magnetic field inhomogeneities and presents a lifetime which is mainly limited only by atomic motion. A theoretical simulation of the measured spectra was also developed and is in very good agreement with the experiment.

  7. Leaching Study in Immobilization of Cesium and Cobalt Radionuclides In Fly Ash- Zeolite Cement

    International Nuclear Information System (INIS)

    Fly ash-zeolite cement was synthesized from industrial by-product fly ash obtained from the thermal electric power station. The synthesis process is based on the hydrothermal-calcination-route of the fly ash. The microstructure of fly ash-zeolite cement was characterized by X-ray diffraction, FT infrared spectroscopy and surface area (F-N2). The efficiency of innovative matrices for immobilizing cesium and cobalt radionuclides is presented in this work. The aim of the present study is to investigate the possibility of solidifying 137Cs and 60Co radionuclides in synthetic fly ash zeolite cement. Leaching behavior of the radionuclides have been studied. The leachability index measured indicated that fly ash zeolite cement matrix can be utilized as an efficient material for immobilizing cesium and cobalt radionuclides than portland cement.

  8. Static and dynamic experiments for the retention of cesium in nitrate containing, nitric acid solutions

    International Nuclear Information System (INIS)

    The separation of cesium from medium active waste (MAW) of the Purex-Process by chromatographic methods is demonstrated using the inorganic ion exchanger ammoniummolybdatophosphate (AMP-1). Other inorganic exchangers like ammoniumhexacyanocobaltousferrate (NCFC), zirkoniumphosphate (ZPH) and antimonypentoxid (HAP) have shown for different pH-values a reasonable retention for cesium (NCFC (pH 12) : 35 g Cs/kgNCFC, ZPH(pH 7) : 100 g Cs/kgZPH and HAP (pH 2) : 55 g Cs/kgHAP). But with a high salt loading (300 g/l NaNO3) a loss of capacities occurs which does not allow the use of these exchangers, whereas AMP-1 is useful from a pH of 9 to conc. HNO3 with this high salt loadings with a capacity of 60 g Cs/kg AMP-1. (orig.)

  9. Kelvin probe studies of cesium telluride photocathode for the AWA photoinjector

    Energy Technology Data Exchange (ETDEWEB)

    Velazquez, D.; Wisniewski, E. E.; Yusof, Z.; Harkay, K.; Spentzouris, L.; Terry, J. [Physics Department at Illinois Institute of Technology, Chicago, IL 60616 and High Energy Physics Division at Argonne National Laboratory, Lemont, IL 60439 (United States); High Energy Physics Division at Argonne National Laboratory, Lemont, IL 60439 (United States); Accelerator Science Division at Argonne National Laboratory, Lemont, IL 60439 (United States); Physics Department at Illinois Institute of Technology, Chicago, IL 60616 (United States)

    2012-12-21

    Cesium telluride is an important photocathode as an electron source for particle accelerators. It has a relatively high quantum efficiency (> 1%), is robust in a photoinjector, and long lifetime. This photocathode is fabricated in-house for a new Argonne Wakefield Accelerator (AWA) beamline to produce high charge per bunch ({approx}50 nC) in a long bunch train. We present some results from a study of the work function of cesium telluride photocathode using the Kelvin Probe technique. The study includes an investigation of the correlation between the quantum efficiency and the work function, the effect of photocathode aging, the effect of UV light exposure on the work function, and the evolution of the work function during and after photocathode rejuvenation via heating.

  10. Strontium-90 and cesium-137 in soil from May 1984 to July 1984

    International Nuclear Information System (INIS)

    Strontium-90 and cesium-137 in soil measured throughout Japan from May to July 1984 are given in pCi/kg and mCi/km2. Sampling points are total of 8 from Kawabe-gun (Akita) to Ibasuki-gun (Kagoshima). Collection and pretreatment of samples, preparation of samples for analysis, separation of strontium-90 and cesium-137, determination of stable strontium, calcium and potassium, and counting are described. Soil was collected from the location in the spacious and flat area without past disturbance on the surface. Soil was taken from two layers of different depths, 0 aproximately 5 cm and 5 approximately 20 cm. After the radiochemical separation, the mounted precipitates were counted for activity using low background beta counters normally for 60 minutes. (Mori, K.)

  11. Characterization of cesium uptake mediated by a potassium transport system of bacteria in a soil conditioner

    International Nuclear Information System (INIS)

    We found that bacteria in a commercial soil conditioner sold in Ishinomaki, Miyagi, exhibited concentrative and saturable cesium ion (Cs+) uptake in the natural range of pH and temperature. The concentration of intracellular Cs+ could be condensed at least a few times higher compared with the outside medium of the cells. This uptake appeared to be mediated by a K+ transport system, since Cs+ uptake was dose-dependently inhibited by potassium ion (K+). Eadie-Hofstee plot analysis indicated that the Cs+ uptake involved a single saturable process. The maximum uptake amount (Jmax) was the same in the presence and absence of K+, suggesting that Cs+ and K+ uptakes were competitive with respect to each other. These bacteria might be useful for bioremediation of cesium-contaminated soil. (author)

  12. Low Level Gamma Spectroscopy Measurements of Radium and Cesium in Lucerne (Medicago Sativa)

    Science.gov (United States)

    Fokapić, S.; Bikit, I.; Mrđa, D.; Vesković, M.; Slivka, J.; Mihaljev, Ž.; Ćupić, Ž.

    2007-04-01

    Nineteen years after Chernobyl nuclear accident, activity concentration of 137Cs still could be detected in food and soil samples in Central and Eastern Europe. In this paper radiation levels of radium and cesium in Lucerne will be presented. It is a perennial plant with a deep root system and it is widely grown throughout the world as forage for cattle. The samples of Lucerne were taken from twelve different locations in Vojvodina in the summer period July-September 2004. The samples were specially dried on the air and after that ground, powdered and mineralized by method of dry burning on the temperature of 450°C. Gamma spectrometry measurements of the ash were performed by means of actively shielded germanium detector with maximal background reduction. For cesium 137Cs 10 mBq/kg order of magnitude detection limits were achieved.

  13. Determination of modelling parameter in the fluctuation and migration of Cesium in soils

    International Nuclear Information System (INIS)

    Cesium radionuclide is one of fission products with high level activity and long life, of about 30 years, therefore it is used as an indicator of a fission product released from a nuclear reactor or a radioactive waste storage. The migration process of cesium in soil is influent by physical and chemical properties of soil and environment in which the sorption process occurred. The data of the physical and chemical properties and the radionuclide retardation in such area are needed for the study of mathematical models of radionuclide migration. The experiment has been performed in laboratory by using soils with particle sizes of -4 - 4.48x10-2 cm/second; the longitudinal dispersivity 0.030 - 0.241 cm; the coefficient of longitudinal dispersion was 4.96x10-5 - 7.69x10-3 cm2/second and retardation factor was 2.30 - 3.39

  14. Chemical treatment of aqueous radioactive Cesium-137 waste using Ferri Chloride

    International Nuclear Information System (INIS)

    Ferric Chloride 6H2O was used for treatment of liquid radioactive wastes containing Cesium-137. Various concentration of ferric chloride 6H2O have been added into the waste at different pH and speed of stirrer. The treatment was based on the coagulans-flocculation and coprecipitation mechanisms. The best result of this experiment was achieved by adding 300 ppm of Ferric chloride 6 H2O into liquid waste on following condition the rate Stirrer was 250 rpm. At this condition, it was found that the separation efficiency and the decontamination factor were 83.32 % and 5.99. The activity of decreasing of aqueous radioactive Cesium-137 waste was 2.10 x 10-4 Ci/l to 3.50 x 10-5 Ci/l

  15. Spectroscopic approach for an electron EDM measurement using neutral cesium atoms

    Science.gov (United States)

    Zhu, Kunyan; Solmeyer, Neal; Weiss, David S.

    2012-06-01

    Observation of a permanent electric dipole moment of the electron (eEDM) would imply CP violating effects not contained in the Standard Model. We describe the state preparation and spectroscopy that will be used to measure the eEDM. Cesium atoms are guided into a measurement chamber, where they are laser-cooled and trapped in a pair of parallel one-dimensional optical lattices. The lattices thread three specially coated glass electric field plates. The measurement chamber is surrounded by a four layer magnetic shield inside of which eight magnetic field coils control the bias and gradient magnetic fields. A series of microwave and low frequency magnetic field pulses transfer the atoms into a superposition state that is sensitive to the eEDM signal. A measurement of the eEDM using neutral cesium atoms can obtain an ultimate shot noise limit of 3x10-30 e-cm.

  16. Adsorption of uranium, cesium and strontium onto coconut shell activated carbon

    International Nuclear Information System (INIS)

    The adsorption of uranium (VI), cesium and strontium ions from aqueous solutions onto a commercial activated carbon obtained by physical activation of coconut shell has been studied in batch systems. In particular the adsorption of uranium, studied as a function of contact time and metal ion concentration, followed pseudo-first-order kinetics. Equilibrium adsorption data were fitted by Langmuir and Freundlich isotherm models and the maximum adsorption capacity of the activated carbon resulted to be 55.32 mg/g. The study showed that the considered activated carbon could be successfully used for uranium adsorption from aqueous solutions. Feasibility of cesium and strontium adsorption onto the same activated carbon has been also investigated. Results showed that no affinities with both of these ions exist. (author)

  17. Stark spectra of Rydberg states in atomic cesium in the vicinity of n=18

    Institute of Scientific and Technical Information of China (English)

    Dong Hui-Jie; Wang Ting; Li Chang-Yong; Zhao Jian-Ming; Zhang Lin-Jie

    2013-01-01

    The Stark structures in a cesium atom around n =18 are numerically calculated.The results show that the components of 20D states with a small azimuthal quantum number |m| shift upward a lot,and those with a large |m| shift downward a little within 1100 V/cm.All components of P states shift downward.Experimental work has been performed in ultracold atomic cesium.Atoms initially in 6P3/2 state are excited to high-n Rydberg states by a polarization light perpendicular to the field,and Stark spectra with 丨m丨=1/2,3/2,5/2 are simultaneously observed with a large linewidth for the first time.The observed spectra are analyzed in detail.The relative transition probability is calculated.The experimental results are in good agreement with our numerical computation.

  18. Mössbauer study on the gamma radiolysis of anhydrous cesium tris (oxalato) ferrate(III)

    Science.gov (United States)

    Ladriere, J.; Senterre, V.; Apers, D.

    1992-04-01

    The final product of the gamma radiolysis of anhydrous cesium tris(oxalato) ferrate(III) has been identified by Mössbauer spectroscopy as Cs2Fe(ox)2. The radiolytic decomposition proceeds as a first-order process due to the original compound depletion and to the radiolytic stability of the ferrous compound. Lamb-Mössbauer factors measurements indicate that the recoilless fractions of the iron species are practically unaffected by the radiolysis.

  19. Spatial variability and the fate of cesium in coastal sediments near Fukushima, Japan

    Directory of Open Access Journals (Sweden)

    E. Black

    2014-05-01

    Full Text Available Quantifying the amount of cesium incorporated into marine sediments as a result of the Fukushima Dai-ichi Nuclear Power Plant (FDNPP accident has proven challenging due to the limited multi-core sampling from within the 30 km zone around the facility, the inherent spatial heterogeneities in ocean sediments, and the potential for inventory fluctuations due to physical, biological, and chemical processes. Using 210Pb, 234Th, 137Cs, and 134Cs profiles from 20 sediment cores, coastal sediment inventories were reevaluated. A minimum 137Cs sediment inventory of 100 ± 50 TBq was found for an area of 55 000 km2 using cores from this study and a total of 130 ± 60 TBq using an additional 181 samples. These inventories represent less than 1% of the estimated 15–30 PBq of cesium released during the FDNPP disaster and constitute ~ 90% of the total coastal inventory of 137Cs remaining in 2012. The time needed for surface sediment activities (0 to 3 cm at the 20 locations to reduce by 50% via bioturbation was estimated to range from 0.4 to 26 years, indicating a much greater persistence of cesium in the sediments relative to coastal water activities. However, due to the observed variability in mixing rates, grain size, and inventories, additional cores are needed to further improve estimates and capture the full extent of cesium penetration into the shallow coastal sediments, which was deeper than 14 cm for all cores retrieved from water depths less than 150 m.

  20. Prussian blue caged in spongiform adsorbents using diatomite and carbon nanotubes for elimination of cesium

    OpenAIRE

    Hu, Baiyang; Fugetsu, Bunshi; Yu, Hongwen; Abe, Yoshiteru

    2012-01-01

    We developed a spongiform adsorbent that contains Prussian blue, which showed a high capacity for eliminating cesium. An in situ synthesizing approach was used to synthesize Prussian blue inside diatomite cavities. Highly dispersed carbon nanotubes (CNTs) were used to form CNT networks that coated the diatomite to seal in the Prussian blue particles. These ternary (CNT/diatomite/Prussian-blue) composites were mixed with polyurethane (PU) prepolymers to produce a quaternary (PU/CNT/diatomite/P...

  1. The effects of different factors at the cesium 137 accumulation by tree plants

    International Nuclear Information System (INIS)

    It was shown that cesium 137 accumulation by tree plants depended from numerous factors that had to be take into account by utilisation of forest production and conducting of forestry in the whole. It is necessary to elaborate a new classification of contaminated forests which could take into account not only radionuclide density of soils but existence of different tree species and their growth conditions

  2. Evaporative cooling of cesium atoms in the gravito-optical surface trap

    CERN Document Server

    Hammes, M; Grimm, R

    2000-01-01

    We report on cooling of an atomic cesium gas closely above an evanescent-wave. Our first evaporation experiments show a temperature reduction from 10muK down to 300nK along with a gain in phase-space density of almost two orders of magnitude. In a series of measurements of heating and spin depolarization an incoherent background of resonant photons in the evanescent-wave diode laser light was found to be the limiting factor at this stage.

  3. Quantized atomic motion in 1D cesium molasses with magnetic field

    International Nuclear Information System (INIS)

    We report the observation of quantized energy levels for the motion of cesium atoms in optical molasses consisting two counterpropagating σ+ beams and a small transverse magnetic field. The observation of overtones proves the existence of at least four bound states in each optical potential well. The absorption spectrum is dramatically modified when an additional longitudinal magnetic field is applied. In particular, a population inversion between quantized levels is observed. (orig.)

  4. Strategic Design and Optimization of Inorganic Sorbents For Cesium, Strontium and Actinides

    Energy Technology Data Exchange (ETDEWEB)

    Hobbs, D.; Nyman, M.; Clearfield, A.; Maginn, E.

    2006-06-01

    The basic science goal in this project identifies structure/affinity relationships for selected radionuclides and existing sorbents. The task will apply this knowledge to the design and synthesis of new sorbents that will exhibit increased affinity for cesium, strontium and actinide separations. The target problem focuses on the treatment of high-level nuclear wastes. The general approach can likewise be applied to nonradioactive separations.

  5. Development of an Advanced Polymeric Composite (ALIX) for separation of cesium from nuclear waste

    International Nuclear Information System (INIS)

    137Cs is one of the major isotopes present in high level radioactive waste (HLW). Its presence makes nuclear waste handling difficult. A new composite (ALIX) containing Ammonium molybdophosphate and a derivative of Bisphenol was developed for column operations to selectively remove cesium from acidic high level nuclear waste. The composite is stable in nitric acid, radiation field and exhibits fast kinetics for uptake. The properties of the composite are attributed to molecular structure of the polymer and morphology of the composite. (author)

  6. Prussian blue as an antidote for radioactive thallium and cesium poisoning

    Directory of Open Access Journals (Sweden)

    Altagracia-Martinez M

    2012-06-01

    Full Text Available Marina Altagracia-Martínez, Jaime Kravzov-Jinich, Juan Manuel Martínez-Núñez, Camilo Ríos-Castañeda, Francisco López-NaranjoDepartments of Biological Systems and Health Care, Biological and Health Sciences Division, Universidad Autónoma Metropolitana-Xochimilco, Mexico DF, MexicoBackground: Following the attacks on the US on September 11, 2001, potentially millions of people might experience contamination from radioactive metals. However, before the specter of such accidents arose, Prussian blue was known only as an investigational agent for accidental thallium and cesium poisoning. The purpose of this review is to update the state of the art concerning use of Prussian blue as an effective and safe drug against possible bioterrorism attacks and to disseminate medical information in order to contribute to the production of Prussian blue as a biodefense drug.Methods: We compiled articles from a systematic review conducted from January 1, 1960 to March 30, 2011. The electronic databases consulted were Medline, PubMed, the Cochrane Library, and Scopus.Results: Prussian blue is effective and safe for use against radioactive intoxications involving cesium-137 and thallium. The US Food and Drug Administration has approved Prussian blue as a drug, but there is only one manufacturer providing Prussian blue to the US. Based on the evidence, Prussian blue is effective for use against radioactive intoxications involving cesium-137 and thallium, but additional clinical research on and production of Prussian blue are needed.Keywords: Prussian blue, radioactive cesium, thallium, intoxication, biodefense drug

  7. Laser-pumped cesium magnetometers for high-resolution medical and fundamental research

    OpenAIRE

    Groeger, Stephan; Bison, Georg; Knowles, Paul E.; Wynands, Robert; Weis, Antoine

    2007-01-01

    Laser-pumped cesium magnetometers allow highly sensitive magnetometry at room temperature. We report on applications of that technique in biomagnetic diagnostics and in a neutron electric dipole moment (nEDM) experiment. In the biomagnetic application the magnetic field from the beating human heart is detected using a gradiometer, which reaches an intrinsic sensitivity of 80 fT/Hz1/2. The device can record time-resolved magnetic field maps above the human body surface with a spatial resolutio...

  8. Cesium under pressure: First-principles calculation of the bcc-to-fcc phase transition

    Science.gov (United States)

    Carlesi, S.; Franchini, A.; Bortolani, V.; Martinelli, S.

    1999-05-01

    In this paper we present the ab initio calculation of the structural properties of cesium under pressure. The calculation of the total energy is done in the local-density approximation of density-functional theory, using a nonlocal pseudopotential including the nonlinear core corrections proposed by Louie et al. The calculation of the pressure-volume diagram for both bcc and fcc structures allows us to prove that the transition from bcc to fcc structure is a first-order transition.

  9. Photoemission from Graphene on Copper and Cesium Antimonide: Theory and Experiment

    Science.gov (United States)

    Finkenstadt, Daniel; Jensen, Kevin L.; Lambrakos, Samuel G.; Shabaev, Andrew; Moody, Nathan A.

    The work function is calculated using DFT for a substrate of flat copper on which a single layer of graphene is deposited. These calculations show a reduced work function, compared to bare copper, when graphene is deposited on a cathode. Based on our DFT-calculated results, a simple model using the transfer matrix approach gives the transmission probability near and above the barrier maximum. An important element of our model is the DFT-calculated, macroscopically-averaged electrostatic potential. Using this potential, graphene behaves as a resonant well for electrons transmitted between the substrate and vacuum regions. Another system to be discussed is graphene atop cesium antimonide, which has very low work function making it technologically useful, in particular for the development of an x-ray free electron laser. On cesium antimonide, we examine whether graphene may allow for the retention of an underlying cesium layer that is often damaged in high-field applications. A discussion of these results in light of recent experimental characterization at LANL will be given. Funding and support provide by ONR and DOE.

  10. Uptake and transport of radioactive cesium and strontium into grapevines after leaf contamination

    Science.gov (United States)

    Zehnder, H. J.; Kopp, P.; Eikenberg, J.; Feller, U.; Oertli, J. J.

    1995-07-01

    From 1989 to 1993 the foliar uptake of radioactive strontium (Sr-85) and cesium (Cs-134) by selected leaves of grapevine plants and the subsequent redistribution within the plants was examined under controlled conditions in a greenhouse. The radionuclides were applied as chlorides. These plants were grown in large pots containing a mixture of local soil and peat. Plant and soil samples were analyzed throughout the growing season and also during the following vegetation period. Only traces of the applied radiostrontium were taken up by the leaves. This element was essentially not redistributed within the plants. In contrast, radiocesium was easily taken up through the leaf surface, transported to other plant parts and to some extent released from the roots into the soil. Cesium reaching the soil may interact with clay particles causing a very reduced availability for plants. Therefore the soil may act as a long-term sink for radiocesium. On the other hand, grape berries represent transient sinks. The cesium levels in the berries decreased again in a late phase of maturation, but the mechanisms causing this loss are not yet identified. During the second vegetation period, only a very minor proportion of the radiocesium taken up previously by the plants was present in the above ground parts.

  11. Strontium-90 and cesium-137 in soil from May to July 1983

    International Nuclear Information System (INIS)

    The measured values in soil of strontium-90 and cesium-137 at a total of 4 locations throughout Japan from May to July, 1983 are given in pCi/kg and mCi/km2 in the tables. The method of measurement is also described: collection and pretreatment of samples, preparation of the samples for analysis, separation of strontium-90 and cesium-137, determination of stable strontium, calcium and potassium, and counting. Soil was collected from the location in the spacious and flat area without any past disturbance. Soil was taken from two layers having different depths: 0--5 cm and 5--20 cm. The sample solution was neutralized with sodium hydroxide. After sodium carbonate was added, the precipitate of strontium and calcium carbonates was separated. The supernatant solution was retained for cesium-137 determination. After the radiochemical separation, the mounted precipitates were counted for activity using a low background beta counter normally for 60 min. The maximum values were 690 pCi/kg for Sr-90 and 1300 pCi/kg for Cs-137, which were obtained from the samples in the 5-to-20 cm depth, in June 1983, at Akita-ken,Japan. (Mori, K.)

  12. Enhanced capacity and stability for the separation of cesium in electrically switched ion exchange

    Energy Technology Data Exchange (ETDEWEB)

    Tawfic, A.F.; Dickson, S.E.; Kim, Y. [McMaster University, Hamilton, ON (Canada); Mekky, W. [AMEC NSS, Power and Process America, Toronto (Canada)

    2015-03-15

    Electrically switched ion exchange (ESIX) can be used to separate ionic contaminants from industrial wastewater, including that generated by the nuclear industry. The ESIX method involves sequential application of reduction and oxidation potentials to an ion exchange film to induce the respective loading and unloading of cesium. This technology is superior to conventional methods (e.g electrodialysis reversal or reverse osmosis) as it requires very little energy for ionic separation. In previous studies, ESIX films have demonstrated relatively low ion exchange capacities and limited film stabilities over repeated potential applications. In this study, the methodology for the deposition of electro-active films (nickel hexacyanoferrate) on nickel electrodes was modified to improve the ion exchange capacity for cesium removal using ESIX. Cyclic voltammetry was used to investigate the ion exchange capacity and stability. Scanning electron microscopy (SEM) was used to characterize the modified film surfaces. Additionally, the films were examined for the separation of cesium ions. This modified film preparation technique enhanced the ion exchange capacity and improves the film stability compared to previous methods for the deposition of ESIX films. (authors)

  13. Kinetic and equilibrium studies of cesium adsorption on ceiling tiles from aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Miah, Muhammed Yusuf [Emergencies Science and Technology Section, Environment Canada, 335 River Road, Ottawa, Ontario, K1A 0H3 (Canada); Department of Applied Chemistry and Chemical Technology, Noakhali Science and Technology University (Bangladesh); Volchek, Konstantin, E-mail: Konstantin.Volchek@ec.gc.ca [Emergencies Science and Technology Section, Environment Canada, 335 River Road, Ottawa, Ontario, K1A 0H3 (Canada); Kuang, Wenxing [SAIC Canada, 335 River Road, Ottawa, Ontario, K1A 0H3 (Canada); Tezel, F. Handan [Department of Chemical and Biological Engineering, University of Ottawa, 161 Louis-Pasteur, Ottawa, Ontario, K1N 6N5 (Canada)

    2010-11-15

    A series of experiments were performed to quantify the adsorption of cesium on ceiling tiles as a representative of urban construction materials. Adsorption was carried out from solutions to mimic wet environmental conditions. Non-radioactive cesium chloride was used as a surrogate of the radioactive {sup 137}Cs. The experiments were performed in the range of initial cesium concentrations of 0.114-23.9 mg L{sup -1} at room temperature (21 deg. C) around three weeks. Solution samples were taken after set periods of time and analyzed by inductively coupled plasma mass spectrometry (ICP-MS). The quantity of adsorbed Cs was calculated by mass balance as a function of time. Two kinetic and three equilibrium models were employed to interpret the test results. Determination of kinetic parameters for adsorption was carried out using the first-order reaction model and the intra-particle diffusion model. Adsorption equilibrium was studied using Langmuir, Freundlich and three-parameter Langmuir-Freundlich adsorption isotherm models. A satisfactory correlation between the experimental and the predicted values was observed.

  14. Derivation of cesium-137 residual radioactive material guidelines for the Peek Street site, Schenectady, New York

    Energy Technology Data Exchange (ETDEWEB)

    Jones, L.; Nimmagadda, M.; Yu, C.

    1992-01-01

    Residual radioactive material guidelines for cesium-137 were derived for the Peek rk. The derivation was based on the requirement that the Street site in Schenectady, New York. The derivation was based on the requirement that the 50-year committed effective dose equivalent to a hypothetical individual who lives or works in the immediate vicinity of the Peek Street site should not exceed a dose of 100 mrem/yr following remedial action. The US Department of Energy (DOE) residual radioactive material guideline computer code, RESRAD was used in this evaluation. Three potential scenarios were considered for the site on the assumption that for a period of 1,000 years following remedial action, the site wig be utilized without radiological restrictions. The scenarios vary with regard to use of the site, time spent at the site, and sources of food consumed. Results indicate that the basic dose limit of 100 mrem/yr will not be exceeded for cesium-137 within 1,000 years, provided that the soil concentration of cesium-137 at the Peek Street site does not exceed the following levels: 98 pCi/g for Scenario A (industrial worker: the expected scenario), 240 pCi/g for Scenario B (recreationist: a plausible scenario), and 34 pCi/g for Scenario C (resident farmer ingesting food produced in the decontaminated area: a plausible scenario).

  15. Cesium and strontium tolerant Arthrobacter sp. strain KMSZP6 isolated from a pristine uranium ore deposit.

    Science.gov (United States)

    Swer, Pynskhem Bok; Joshi, Santa Ram; Acharya, Celin

    2016-12-01

    Arthrobacter sp. KMSZP6 isolated from a pristine uranium ore deposit at Domiasiat located in North-East India exhibited noteworthy tolerance for cesium (Cs) and strontium (Sr). The strain displayed a high minimum inhibitory concentration (MIC) of 400 mM for CsCl and for SrCl2. Flow cytometric analysis employing membrane integrity indicators like propidium iodide (PI) and thiazole orange (TO) indicated a greater sensitivity of Arthrobacter cells to cesium than to strontium. On being challenged with 75 mM of Cs, the cells sequestered 9612 mg Cs g(-1) dry weight of cells in 12 h. On being challenged with 75 mM of Sr, the cells sequestered 9989 mg Sr g(-1) dry weight of cells in 18 h. Heat killed cells exhibited limited Cs and Sr binding as compared to live cells highlighting the importance of cell viability for optimal binding. The association of the metals with Arthrobacter sp. KMSZP6 was further substantiated by Field Emission-Scanning Electron Microscopy (FE-SEM) coupled with Energy dispersive X-ray (EDX) spectroscopy. This organism tolerated up to 1 kGy (60)Co-gamma rays without loss of survival. The present report highlights the superior tolerance and binding capacity of the KMSZP6 strain for cesium and strontium over other earlier reported strains and reveals its potential for bioremediation of nuclear waste. PMID:27620733

  16. Study on magnetic separation for decontamination of cesium contaminated soil by using superconducting magnet

    International Nuclear Information System (INIS)

    Highlights: • The method for the soil decontamination by the superconducting magnet is proposed. • Magnetic separation of clay minerals was performed by HGMS. • Soil separation ratio was evaluated by quantitative analysis using XRD. • It is expected that HGMS can be applied to the actual soil decontamination. - Abstract: The accident of Fukushima Daiichi nuclear power plant caused the diffusion of radioactive cesium over the wide area. We examined the possibility of applying magnetic separation method using the superconducting magnet, which can process a large amount of the soil in high speed, to the soil decontamination and volume reduction of the radioactive cesium contaminated soil. Clay minerals are classified as 2:1 and 1:1 types by the difference of their layer structures, and these types of minerals are respectively paramagnetic and diamagnetic including some exception. It is known that most of the radioactive cesium is strongly adsorbed on the clay, especially on 2:1 type clay minerals. It is expected that the method which can separate only 2:1 type clay minerals selectively from the mixture clay minerals can enormously contribute to the volume reduction of the contaminated soil. In this study, the components in the clay before and after separation were evaluated to estimate the magnetic separation efficiency by using X-ray diffraction. From the results, the decontamination efficiency and the volume reduction ratio were estimated in order to examine the appropriate separation conditions for the practical decontamination of the soil

  17. ION EXCHANGE MODELING FOR REMOVAL OF CESIUM FROM HANFORD WASTE USING SUPERLIG 644 RESIN

    Energy Technology Data Exchange (ETDEWEB)

    Hamm, L

    2004-05-01

    The expected performance of a proposed ion exchange column using SuperLig{reg_sign} 644 resin for the removal of cesium from Hanford high level radioactive alkaline waste is discussed. This report represents a final report on the ability and knowledge with regard to modeling the Cesium-SuperLig{reg_sign} 644 resin ion exchange system. Only the loading phase of the cycle process is addressed within this report. Pertinent bench-scale column tests and batch equilibrium experiments are addressed. The methodology employed and sensitivity analyses are also included (i.e., existing methodology employed is referenced to prior developmental efforts while updated methodology is discussed). Pilot-scale testing is not assessed since no pilot-scale testing was available at the time of this report. Column performance predictions are made considering three selected feed compositions under nominal operating conditions. The sensitivity analyses provided help to identify key parameters that aid in resin procurement acceptance criteria. The methodology and application presented within this report reflect the expected behavior of SuperLig{reg_sign} 644 resin manufactured at the production-scale (i.e, 250 gallon batch size level). The primary objective of this work was, through modeling and verification based on experimental assessments, to predict the cesium removal performance of SuperLig{reg_sign} 644 resin for application in the RPP pretreatment facility.

  18. Derivation of cesium-137 residual radioactive material guidelines for the Peek Street site, Schenectady, New York

    International Nuclear Information System (INIS)

    Residual radioactive material guidelines for cesium-137 were derived for the Peek rk. The derivation was based on the requirement that the Street site in Schenectady, New York. The derivation was based on the requirement that the 50-year committed effective dose equivalent to a hypothetical individual who lives or works in the immediate vicinity of the Peek Street site should not exceed a dose of 100 mrem/yr following remedial action. The US Department of Energy (DOE) residual radioactive material guideline computer code, RESRAD was used in this evaluation. Three potential scenarios were considered for the site on the assumption that for a period of 1,000 years following remedial action, the site wig be utilized without radiological restrictions. The scenarios vary with regard to use of the site, time spent at the site, and sources of food consumed. Results indicate that the basic dose limit of 100 mrem/yr will not be exceeded for cesium-137 within 1,000 years, provided that the soil concentration of cesium-137 at the Peek Street site does not exceed the following levels: 98 pCi/g for Scenario A (industrial worker: the expected scenario), 240 pCi/g for Scenario B (recreationist: a plausible scenario), and 34 pCi/g for Scenario C (resident farmer ingesting food produced in the decontaminated area: a plausible scenario)

  19. Study on magnetic separation for decontamination of cesium contaminated soil by using superconducting magnet

    Energy Technology Data Exchange (ETDEWEB)

    Igarashi, Susumu, E-mail: igarashi@qb.see.eng.osaka-u.ac.jp; Nomura, Naoki; Mishima, Fumihito; Akiyama, Yoko, E-mail: yoko-ak@see.eng.osaka-u.ac.jp

    2014-09-15

    Highlights: • The method for the soil decontamination by the superconducting magnet is proposed. • Magnetic separation of clay minerals was performed by HGMS. • Soil separation ratio was evaluated by quantitative analysis using XRD. • It is expected that HGMS can be applied to the actual soil decontamination. - Abstract: The accident of Fukushima Daiichi nuclear power plant caused the diffusion of radioactive cesium over the wide area. We examined the possibility of applying magnetic separation method using the superconducting magnet, which can process a large amount of the soil in high speed, to the soil decontamination and volume reduction of the radioactive cesium contaminated soil. Clay minerals are classified as 2:1 and 1:1 types by the difference of their layer structures, and these types of minerals are respectively paramagnetic and diamagnetic including some exception. It is known that most of the radioactive cesium is strongly adsorbed on the clay, especially on 2:1 type clay minerals. It is expected that the method which can separate only 2:1 type clay minerals selectively from the mixture clay minerals can enormously contribute to the volume reduction of the contaminated soil. In this study, the components in the clay before and after separation were evaluated to estimate the magnetic separation efficiency by using X-ray diffraction. From the results, the decontamination efficiency and the volume reduction ratio were estimated in order to examine the appropriate separation conditions for the practical decontamination of the soil.

  20. DFB-ridge laser diodes at 894 nm for Cesium atomic clocks

    Science.gov (United States)

    von Bandel, N.; Garcia, M.; Lecomte, M.; Larrue, A.; Robert, Y.; Vinet, E.; Driss, O.; Parrilaud, O.; Krakowski, M.; Gruet, F.; Matthey, R.; Mileti, G.

    2016-02-01

    Time and frequency applications are in need of high accuracy and high stability clocks. Optically pumped compact industrial Cesium atomic clocks are a promising approach that could satisfy these demands. However, the stability of these clocks relies, among others, on the performances of the laser diodes that are used. This issue has led the III-V Lab to commit to the European Euripides-LAMA project that aims to provide competitive compact optical Cesium clocks for ground applications. This work will provide key experience for further space technology qualification. III-V Lab is in charge of the design, fabrication and reliability of Distributed-Feedback diodes (DFB) at 894 nm (D1 line of Cesium) and 852 nm (D2 line). LTF-Unine is in charge of their spectral characterisation. The use of D1 line for pumping will provide simplified clock architecture compared to the D2 line pumping thanks to simpler atomic transitions and a larger spectral separation between lines in the 894 nm case. Also, D1 line pumping overcomes the issue of unpumped "idle states" that occur with D2 line. The modules should provide narrow linewidth (= 10 Hz and 109 Hz2/Hz @ f >= 10 Hz.

  1. ION EXCHANGE MODELING FOR REMOVAL OF CESIUM FROM HANFORD WASTE USING SUPERLIG 644 RESIN

    International Nuclear Information System (INIS)

    The expected performance of a proposed ion exchange column using SuperLig(regsign) 644 resin for the removal of cesium from Hanford high level radioactive alkaline waste is discussed. This report represents a final report on the ability and knowledge with regard to modeling the Cesium-SuperLig(regsign) 644 resin ion exchange system. Only the loading phase of the cycle process is addressed within this report. Pertinent bench-scale column tests and batch equilibrium experiments are addressed. The methodology employed and sensitivity analyses are also included (i.e., existing methodology employed is referenced to prior developmental efforts while updated methodology is discussed). Pilot-scale testing is not assessed since no pilot-scale testing was available at the time of this report. Column performance predictions are made considering three selected feed compositions under nominal operating conditions. The sensitivity analyses provided help to identify key parameters that aid in resin procurement acceptance criteria. The methodology and application presented within this report reflect the expected behavior of SuperLig(regsign) 644 resin manufactured at the production-scale (i.e, 250 gallon batch size level). The primary objective of this work was, through modeling and verification based on experimental assessments, to predict the cesium removal performance of SuperLig(regsign) 644 resin for application in the RPP pretreatment facility

  2. Stationary point of the radiometric control of cesium contamination of agricultural animals

    International Nuclear Information System (INIS)

    Stationary point of the radiometric control of cesium contamination of an agricultural animals. Is intended for vital measurements of the contents of radiocesium in muscular tissue of a cattle. Can be used on cattle-breeding farms, providing points, in meat factories and personal facilities. As a base means for accommodation of the control point the motor-car is used. Design of the car allows to automate operations on deployment of the control point on a place and translation of one to a transport mode. Limits of measured specific activity of cesium contamination of a cattle is up 5*10-9 to 5*10-6 Ci/kg. The basic error on the bottom limit of measurement at confidence coefficient 0,95 is no more than 30%. Measurement time for the bottom limit of determined specific activity is no more than 30 s. There is automatic measurement mode. Type of a power is 220 V, 50 Hz. Range of working temperatures is up -15 to +35 centigrade. Relative humidity is no more than 98% at 25 centigrade. External gamma background is till 0.035 mR/h. Time of installation and dismantle of stationary control point is no more than 1,5 hours. The direct radiometric control in divo allows to fulfil and to use biotechnological process of removing of cesium isotopes from body of animals for decrease of levels of radioactive contamination

  3. Crown bridged thiacalix[4]arenes as cesium-selective ionophores in solvent polymeric membrane electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Bereczki, Robert [Technical Analytical Research Group of the Hungarian Academy of Sciences, Department of General and Analytical Chemistry, Budapest University of Technology and Economics, Szt. Gellert ter 4, H-1111 Budapest (Hungary); Csokai, Viktor [Department of Organic Chemical Technology, Budapest University of Technology and Economics, Muegyetem rkp.3, H-1111 Budapest (Hungary); Gruen, Alajos [Department of Organic Chemical Technology, Budapest University of Technology and Economics, Muegyetem rkp.3, H-1111 Budapest (Hungary); Bitter, Istvan [Department of Organic Chemical Technology, Budapest University of Technology and Economics, Muegyetem rkp.3, H-1111 Budapest (Hungary); Toth, Klara [Technical Analytical Research Group of the Hungarian Academy of Sciences, Department of General and Analytical Chemistry, Budapest University of Technology and Economics, Szt. Gellert ter 4, H-1111 Budapest (Hungary)]. E-mail: ktoth@mail.bme.hu

    2006-05-31

    Novel 1,3-alternate thiacalix[4]mono- and biscrown-6 ethers were studied as ionophores in poly(vinyl chloride) membrane electrodes. Their selectivity behavior was characterized with respect to large number of cations, including potential interferents in environmental samples, and the membrane composition was optimized for cesium ion response. Among the ionophores, 1,3-alternate thiacalix[4]mono(crown-6) ether showed, especially high selectivity for cesium over other alkali-metal ions. Transition and heavy metal ions did not interfere seriously with the electrode response, which indicates that the bridging sulfur atoms do not take part in the ion recognition process. The potentiometric cesium responses of all electrodes involved in this study were found close to Nernstian and the detection limits were lower than 10{sup -7} M. The Cs{sup +}/Na{sup +} selectivity of the different ionophore-based sensors and the solvent extraction ability of the ligands were interpreted based on the respective constants of complex formation.

  4. Temperature and number evolution of cold cesium atoms inside a wall-coated glass cell

    Institute of Scientific and Technical Information of China (English)

    黄家强; 张建伟; 王时光; 王力军

    2015-01-01

    We report an experimental study on the temperature and number evolution of cold cesium atoms diffusively cooled inside a wall-coated glass cell by measuring the absorption profile of the 62S1/2 (F=4)→62P3/2(F0=5) transition line with a weak probe laser in the evolution process. We found that the temperature of the cold atoms first gradually decreases from 16 mK to 9 mK, and then rapidly increases. The number of cold atoms first declines slowly from 2.1 × 109 to 3.7 × 108 and then falls drastically. A theoretical model for the number evolution is built and includes the instantaneous temperature of the cold atoms and a fraction p, which represents the part of cold cesium atoms elastically reflected by the coated cell wall. The theory is overall in good agreement with the experimental result, and a nonzero value is obtained for the fraction p, which indicates that the cold cesium atoms are not all heated to the ambient temperature by a single collision with the coated cell wall. These results can provide helpful insight for precision measurements based on diffuse laser cooling.

  5. Small-Scale Ion Exchange Removal of Cesium and Technetium from Hanford Tank 241-AN-103

    Energy Technology Data Exchange (ETDEWEB)

    Hassan, N.M.

    2000-07-27

    The pretreatment process for BNFL, Inc.'s Hanford River Protection Project is to provide decontaminated low activity waste and concentrated eluate streams for vitrification into low activity and high level waste glass, respectively. The pretreatment includes sludge washing, filtration, precipitation, and ion exchange processes to remove entrained solids, cesium, transuranics, technetium, and strontium. The ion exchange removal of cesium (Cs) and technetium (Tc) ions is accomplished by using SuperLig 644, and 639 resins from IBC Advanced Technologies, American Fork, Utah. The resins were shown to selectively remove cesium and technetium (as pertechnetate), from alkaline salt solutions. The efficiency of ion exchange column loading and elution is a complex function involving feed compositions, equilibrium and kinetic behavior of ion exchange resins, diffusion, and the ionic strength and pH of the aqueous solution. A previous experimental program completed at the Savannah River Technology Center demonstrated the conceptualized flow sheet parameters with a similar Hanford tank sample (241-AW-101). Those experiments included determination of Cs and Tc batch distribution coefficients by SuperLig 644 and 639 resins and demonstration of small-scale column breakthrough and elution. The experimental findings were used in support of preliminary design bases and pretreatment flow sheet development by BNFL, Inc.

  6. Determination of collisional ionization rate and ionization yield from excited levels of cesium in a flame

    International Nuclear Information System (INIS)

    A method is proposed for determining the rate constants of collisional ionization and the ionization yield from excited levels of cesium atoms in a flame, using experimental curves of optical saturation and laser-stimulated ionization of excited atoms. It is shown that deviations of the shape of the saturation curves from ideal shape are due to the time dependence of the trailing edge of the exciting laser pulse. The ionization yield of cesium in an acetylene--air flame during its one-step excitation to the 6p2p1/2 level was 0.95%, rising to 50% for two-step excitation to the 8d2D3/2 level. The corresponding values of the rate constants of collisional ionization were 3.2x105 and 3.3x107 sec-1. From the known value of the ionization yield in the two-step excitation scheme, estimates of the atomization coefficient of cesium in the flame were made. The proposed method can be used for other elements in different flames

  7. Temperature and number evolution of cold cesium atoms inside a glass cell

    CERN Document Server

    Huang, J Q; Wang, S G; Wang, Z B; Wang, L J

    2015-01-01

    We report an experimental study on the temperature and number evolution of the cold cesium atoms diffusively cooled inside a wall-coated glass cell by measuring the absorption profile of the 62S1/2 (F=4)-62P3/2 (F'=5) transition line with a weak probe laser in the evolution process. We found that the temperature of the cold atoms first gradually decreases from 16 mK to 9 mK, and then rapidly increases. A theoretical model of the number evolution is built, which includes the temperature of the cold atoms and the fraction p of the cold cesium atoms elastically reflected by the cell wall. The theoretical model is consistent with the experimental result very well, and the fraction p is obtained to be (0.58 +/- 0.03), which reveals that the cold cesium atoms are not all heated to the ambient temperature by a single collision with the cell wall.

  8. Fire Safety Tests for Cesium-Loaded Spherical Resorcinol Formaldehyde Resin: Data Summary Report

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Dong-Sang; Schweiger, Michael J.; Peterson, Reid A.

    2012-09-01

    A draft safety evaluation of the scenario for spherical resorcinol formaldehyde (SRF) resin fire inside the ion exchange column was performed by the Hanford Tank Waste Treatment and Immobilization Plant (WTP) Fire Safety organization. The result of this draft evaluation suggested a potential change of the fire safety classification for the Cesium Ion Exchange Process System (CXP) emergency elution vessels, equipment, and piping. To resolve this question, the fire properties of the SRF resin were measured by Southwest Research Institute (SwRI) through a subcontract managed by Pacific Northwest National Laboratory (PNNL). The results of initial fire safety tests on the SRF resin were documented in a previous report (WTP-RPT-218). The present report summarizes the results of additional tests performed by SwRI on the cesium-loaded SRF resin. The efforts by PNNL were limited to summarizing the test results provided by SwRI into one consolidated data report. The as-received SwRI report is attached to this report in the Appendix A. Where applicable, the precision and bias of each test method, as given by each American Society for Testing and Materials (ASTM) standard procedure, are included and compared with the SwRI test results of the cesium-loaded SRF resin.

  9. Optically pumped semiconductor lasers: Conception and characterization of a single mode source for Cesium atoms manipulation

    International Nuclear Information System (INIS)

    Lasers currently used in atomic clocks or inertial sensors are suffering from a lack of power, narrow linewidth or compactness for future spatial missions. Optically pumped semiconductor lasers, which combine the approach of classical solid state lasers and the engineering of semiconductor laser, are considered here as a candidate to a metrological laser source dedicated to the manipulation of Cesium atoms in these instruments. These lasers have demonstrated high power laser emission in a circular single transverse mode, as well as single longitudinal mode emission, favoured by the semiconductor structure and the external cavity design. We study the definition and the characterization of a proper semiconductor structure for the cooling and the detection of Cesium atoms at 852 nm. A compact and robust prototype tunable on the Cesium D2 hyperfine structure is built. The laser frequency is locked to an atomic transition thanks to a saturated absorption setup. The emission spectral properties are investigated, with a particular attention to the laser frequency noise and the laser linewidth. Finally, we describe and model the thermal properties of the semiconductor structure, which enables the simulation of the laser power characteristic. The experimental parameters are optimised to obtain the maximum output power with our structure. Thanks to our analysis, we propose several ways to overcome these limitations, by reducing the structure heating. (authors)

  10. Cesium removal demonstration utilizing crystalline silicotitanate sorbent for processing Melton Valley Storage Tank supernate: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Walker, J.F. Jr.; Taylor, P.A.; Cummins, R.L. [and others

    1998-03-01

    This report provides details of the Cesium Removal Demonstration (CsRD), which was conducted at Oak Ridge National Laboratory (ORNL) on radioactive waste from the Melton Valley Storage Tanks. The CsRD was the first large-scale use of state-of-the-art sorbents being developed by private industry for the selective removal of cesium and other radionuclides from liquid wastes stored across the DOE complex. The crystalline silicotitanate sorbent used in the demonstration was chosen because of its effectiveness in laboratory tests using bench-scale columns. The demonstration showed that the cesium could be removed from the supernate and concentrated on a small-volume, solid waste form that would meet the waste acceptance criteria for the Nevada Test Site. During this project, the CsRD system processed > 115,000 L (30,000 gal) of radioactive supernate with minimal operational problems. Sluicing, drying, and remote transportation of the sorbent, which could not be done on a bench scale, were successfully demonstrated. The system was then decontaminated to the extent that it could be contact maintained with the use of localized shielding only. By utilizing a modular, transportable design and placement within existing facilities, the system can be transferred to different sites for reuse. The initial unit has now been removed from the process building and is presently being reinstalled for use in baseline operations at ORNL.

  11. Fabrication of stimuli-sensitive hydrogel for the removal of cesium

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Hee-Man; Bong, Sang Bum; Park, Chan Woo; Lee, Kune Woo; Seo, Bum-Kyoung; Moon, Jei Kwon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    The nuclear accident at the Fukushima Daiichi nuclear power station in 2011 released a huge quantity of radioactive contaminants into the environment.1 Among these, cesium Cs-137 is the most problematic contaminant due to its long half-life (30.2 years), and high-energy gamma ray (γ-ray) emissions. 2 Various surface including road, roof, house, building were contaminated with Cs-137. These coating materials have some problems and limitation such as toxic component, and lack of reusability of materials related to the cost. Thus, a more cost-effective and environmental friendly coating materials is still desired. 3 In the present study, the stimuli-sensitive hydrogel were fabricated for the removal of radioactive Cs from solid surface. We describe the morphology, structure, and physical property of these stimuli sensitive hydrogel. In addition, their ability to eliminate cesium was also evaluated. The smart hydrogel coating materials showed an excellent morphology change from the liquid to film by addition of Ca ion. Therefore, the stimuli-sensitive hydrogel demonstrated good potential for the treatment of contaminated surface for the removal of radioactive cesium.

  12. The effect of organic amendment on mobility of cesium in tropical soils - The effect of organic amendment on sorption mechanisms for cesium and cobalt in tropical soils

    Energy Technology Data Exchange (ETDEWEB)

    Wasserman, M.A.V.; Santos-Oliveira, R. [Instituto de Engenharia nuclear/CNEN. Rua Helio de Almeida, 75. Cidade Universitaria - Ilha do Fundao, Rio de Janeiro, RJ. CEP 21941-906 (Brazil); Garcia, R.J.L.; Ferreira, A.C.M.; Rochedo, E.R.R.; Sobrinho, G.A.N. [Instituto de Radioprotecao e Dosimetria/CNEN. Av. Salvador Allende s /no. Rio de Janeiro, RJ. CEP: 22780-160 (Brazil); Perez, D.V. [Centro Nacional de Pesquisa de Solos/EMBRAPA. R. Jardim Botanico, 1024.Rio de Janeiro, RJ, CEP: 22460-000 (Brazil); Wasserman, J.C. [dUFF Network of Environment and Sustainable Development (REMADS-UFF), University Federal Fluminense, Niteroi, RJ (Brazil)

    2014-07-01

    This work aimed to investigate the mechanisms involved in the sorption of {sup 137}Cs and {sup 60}Co as a function of the physico-chemical properties of some types of Brazilian soils and the changes on the behavior of these radionuclides due to changes in soil properties promoted by organic amendment. The experimental study was conducted in a controlled area, where pots containing different types of soils (Ferralsol, Nitisol and Histosol) and different doses of organic amendment (no amendment; 2 kg.m{sup -2} and 4 kg.m{sup -2}) were spiked with {sup 137}Cs and {sup 60}Co. The organic amendment used in this experiment was obtained in the Unit of Compost of the Organic Material of Pinheiral (RJ, Brazil), where the compost is made up from the leaves swept from the streets of the Pinheiral city. The mobility of these radionuclides in the soil was assessed through sequential chemical extraction and desorption studies as a function of pH. The bioavailability was evaluated through the effective absorption of radionuclide by root crops (Raphanus sativus, L). This study evidenced that the organic amendment plays an important role in the desorption processes of cobalt and cesium, reducing desorption of both nuclides beneath higher organic amendment dose. This behavior was observed in acid conditions as well in alkaline. However extreme acid conditions may mobilize both radionuclides, although cobalt mobility was shown to be more sensitive to low pH than cesium. (authors)

  13. The effect of organic amendment on mobility of cesium in tropical soils - The effect of organic amendment on sorption mechanisms for cesium and cobalt in tropical soils

    International Nuclear Information System (INIS)

    This work aimed to investigate the mechanisms involved in the sorption of 137Cs and 60Co as a function of the physico-chemical properties of some types of Brazilian soils and the changes on the behavior of these radionuclides due to changes in soil properties promoted by organic amendment. The experimental study was conducted in a controlled area, where pots containing different types of soils (Ferralsol, Nitisol and Histosol) and different doses of organic amendment (no amendment; 2 kg.m-2 and 4 kg.m-2) were spiked with 137Cs and 60Co. The organic amendment used in this experiment was obtained in the Unit of Compost of the Organic Material of Pinheiral (RJ, Brazil), where the compost is made up from the leaves swept from the streets of the Pinheiral city. The mobility of these radionuclides in the soil was assessed through sequential chemical extraction and desorption studies as a function of pH. The bioavailability was evaluated through the effective absorption of radionuclide by root crops (Raphanus sativus, L). This study evidenced that the organic amendment plays an important role in the desorption processes of cobalt and cesium, reducing desorption of both nuclides beneath higher organic amendment dose. This behavior was observed in acid conditions as well in alkaline. However extreme acid conditions may mobilize both radionuclides, although cobalt mobility was shown to be more sensitive to low pH than cesium. (authors)

  14. The Effect of Pressure and Organic Constituents on the Cesium Ion Exchange Performance of IONSIV IE-911

    International Nuclear Information System (INIS)

    This study examined cesium (137Cs) ion exchange of crystalline silicotitanate (CST) in simulated waste solution. In particular, the study focused on the effect of CST pretreatment on the kinetics and extent of cesium adsorption. The test used IONSIV IE-911 (UOP LLC, Molecular Sieves Division, Des Plaines, IL), the engineered form of CST. Pretreatment steps examined include: soaking CST in 2M NaOH solution for three days, exposing CST to 50% relative humidity for one week, flowing organic-containing (saturated) salt solution through a CST packed bed (at 5 cm/min. superficial velocity), or drying CST in air at 100 C for three days. Some tests occurred under 50 and 25 psig of argon. The following conclusions summarize the results. Pretreatment of IE-911 in organic-containing (e.g., tri-n-butyl phosphate, dibutylphosphate, butanol, paraffin and Dow Corning H-10 defoamer) simulated waste or simulated waste yielded a 83% slower rate of cesium adsorption and 56% lower cesium capacity after one week. Pretreatment of IE-911 in 2M caustic solution for 48 hours yielded a slower approach to equilibrium cesium distribution in batch contact tests--7.7 mL/(g*h) during the first 48 hours and 2.4 ml/(g*h) thereafter. Carboxylates and adsorbed carbonates inside the pores likely affect the cesium transport by either increasing the path-length or reducing mass transfer rate. Heating IE-911 as received from the vendor at 100 C for 24 hours significantly degraded its cesium removal performance by a 40.7% reduction in capacity and 43% reduction in sorption rate over one week of testing. Testing determined nearly identical distribution coefficients Kd between lot numbersign 9990-9681-0004 and 9990-9881-0005 (i.e., difference of only 5.6%). Tests measuring water insertion rates into IE-911 show that hydration of the IE-911 does not appear to limit the rate of cesium sorption. Increasing the atmospheric pressure from 0 to 50 psig had no effect on cesium sorption. Note that lower apparent

  15. Iodine-131 therapy for the treatment of multinodular goitre

    Energy Technology Data Exchange (ETDEWEB)

    Akerman, R.L.; Howarth, D.M. [John Hunter Hospital, Newcastle, NSW, (Australia). Department of Nuclear Medicine

    1997-09-01

    Full text: The purpose of this study was to investigate the effectiveness of {sup 131}l therapy for toxic and non-toxic multinodular goitre (MNG)in the patients treated with the standard dose of 4 x 555 MBq (total 2.2 Bq) and therefore give some indication as to the adequacy of this therapy. This was a retrospective study using information from patients` notes. All patients with large multinodular goitres who had radioiodine therapy for treatment of MNG since 1991 were selected. Data obtained included age, gender, pre, peri and post therapy symptoms and serial biochemical thyroid function results. Each patient was followed for a minimum of six months. The subjects were 35 patients (32 female, three male) with an age range of 37 - 87 years. 26 patients had non-toxic MNG, nine patients had toxic MNG, 24 patients had retrosternal or obstructive symptoms and five patients had had previous thyroid therapy. The patients with retrosternal or obstructive symptoms experienced a reduction in those symptoms. 8.6 per cent of the patients experienced no change at all in symptoms. 2.8 per cent of the patients experienced non-transient side effects (sore throat). 32.8 per cent of the patients experienced transient hyperthyroidism during {sup 131}I therapy. In the toxic group, 77.8 per cent became euthyroid. 11.1 per cent became hypothyroid and 11.1 per cent remained hyperthyroid and required additional treatment. In the non-toxic group, 42.3 per cent became hypothyroid and 57.7 per cent remained euthyroid. The overall incidence of hypothyoidism was 34.4 per cent. The results of this study suggests {sup 131}l therapy in the form of 4 x 555 MBq oral doses (one dose per month for four months) is effective, efficient, relatively risk-free, easy and generally well-tolerated treatment for toxic and non-toxic multinodular goitre.

  16. The Application Value of 131 I Whole Body Imaging in Small Doses in the 131 I Treatment of Differentiated Thyroid Carcinoma%小剂量131I 全身显像在131I治疗分化型甲状腺癌中的应用价值

    Institute of Scientific and Technical Information of China (English)

    黄谋清; 张水香; 曾小建; 陈华

    2014-01-01

    Objective:To research on the application value of 131 I whole body imaging in small doses in the 131 I treatment of thyroid carcinoma. Methods:131 I whole body imaging in small doses was performed before and after their 131 I treatment to 15 cases of differentiated thyroid carcinoma patients who needed 131 I therapy after surgery. Differences of the results of the two 131 I whole body imaging in small doses were analyzed. Results:When 131 I whole body imaging in small doses were performed,28 lesions were found in the 15 cases;43 lesions,including 20 newly lesions,were found during 131 I whole body imaging after 131 I therapy,while 5 lesions in the first examination disappeared. There was no change in 7 cases. Conclusion:Although the sensitivity of small doses of 131 I whole body imaging to discover thyroid cancer metastases is less than a therapeutic dose of 131 I whole body imaging,it is still valuable to perform a 131 I whole body imaging in small dose before the 131I treatment of differentiated thyroid carcinoma.%目的:研究小剂量131 I 全身显像在131 I 治疗甲状腺癌中的应用价值。方法:15例需要在手术后进行131 I 治疗的分化型甲状腺癌病例,在做131 I 治疗前进行小剂量的131 I 全身显像检查,并在131 I 治疗后再次进行全身显像检查,分析两组结果的差异性。结果:小剂量131 I 全身显像时,15例病例中共发现28个病灶,131 I 治疗后进行的全身显像共发现43个病灶,新增病灶20个,减少病灶5个,7例病例病灶无变化。结论:虽然小剂量131 I 全身显像发现甲状腺癌转移灶的敏感性不及治疗剂量131 I 全身显像,但在131 I 治疗分化型甲状腺癌前做小剂量的131 I 全身显像仍然很有价值。

  17. Treatments with radioactive iodine, 131 I. How, when and where?

    International Nuclear Information System (INIS)

    A great variety of approaches exists in the application of the treatments with radioactive materials, as the 131I, but it is necessary to standardize them for the patient's benefit, because their doctor doesn't always know the principle that it bases this therapy, called metabolic therapy or radioiodine therapy (RYT). In this work the experience that was acquired by more of 50 years of RYT management in the Thyroid and Nuclear Medicine Clinic in patients with thyroid pathologies is informed, so that their management fulfills its function and it was carried out inside the corresponding juridical frame and the physicochemical and endocrinological principles that should take implicit. (Author)

  18. Evaluation of irradiation in patient's environment receiving 131I therapy

    International Nuclear Information System (INIS)

    This article describes measurements made in the bed station of Clinic of Nuclear Medicine in St. Elizabeth Oncological Institute in Bratislava. There are treated thyroid cancer and thyrotoxicosis with the use of 131I. The aim of the measurements was to determine the possibility of the ambulation treatment of thyrotoxicosis or the possibility of shortening of the patient;s stay in the bed station that the effective dose would not be exceeded suggestions according to the publication of EURATOM. The measurements were made also with thyroid cancer patients but owing to clinical reasons the ambulation treating in this case is not permissible. Therefore this article does not describe the results of these measurements.The effective dose rates were measured in 0.25 m; 0.5 m; 1 m and 2 m distances from the patient's thyroid so the effective dose in the patient's surroundings could be determined. To the present time the results of effective dose rates measurements for 17 patients were evaluated by described way. The age of the patients was from 41 to 82 years, the administered quantity of 131I was from 259 to 481 MBq, in fractions 37 MBq, 74 MBq, or 111 MBq. The calculated effective half-life of 131I excretion from the patients body is crucial for the length of patient's necessary staying in the bed station, were from 4.2 days to 8 days. This great extend of values is given by by the different clinical parameters of the treated patients. After the analyse of them can be said that the effective half-life increases, when the patient is elder, has greater mass of thyroid and the accumulation is higher. At the present time authors don't suggest using the ambulation treatment of thyrotoxicosis by 131I. For discharging the patient from the hospital authors suggest to think criteria according to the model of behaviour D with the effective dose limit 0.5 mSv. For the households with children up to 2 years and/or pregnant women according to the model B with effective dose limit 0

  19. Iodine 131 ablation of an obstructive lingual thyroid

    Directory of Open Access Journals (Sweden)

    Lester Johnson

    2009-01-01

    Full Text Available A 48-year-old woman undergoing surgery could not be intubated because of an oropharyngeal mass. CT and MRI revealed a 3 cm possible lingual thyroid mass, confirmed by Iodine-123 SPECT/CT. The patient underwent successful Iodine-131 ablation and has done well on thyroid hormone-replacement therapy. This case also demonstrates how modern cross-sectional imaging like SPECT/CT can appropriately be used in the patient diagnosis and management, and is of additional interest for including pre- and post-therapy MRI documenting efficacy morphologically.

  20. Distribution of 131 I- labeled Bothrops erythromelas venom in mice

    International Nuclear Information System (INIS)

    Bothrops erythromelas is responsible for many snake bites in northeastern Brazil. In the present study we determined the in vivo distribution of the venom following its subcutaneous injection into mice. B. erythromelas venom and albumin were labeled individually with 131 I by the chloramine T method, and separated in a Sephacryl S-200 column. The efficiency of labeling was 68%.Male Swiss mice (40-45 g), which had been provided with drinking water containing 0.05% KI over a period of 10 days prior to the experiment, were inoculated dorsally (sc) with 0.3 ml (2.35 x 105 cpm/mouse) of 131 I-venom (N = 42), 131 -albumin or 131 I (controls, N = 28 each). Thirty minutes and 1,3, 6, 12, 18 and 24 h after inoculation, the animals were perfused with 0.85% Na Cl and skin and various organs were collected in order to determine radioactivity content. There was a high rate of venom absorption int he skin (51%) within the first 30 min compared to albumin (20.1%) and free iodine (8.2%). Up to the third hour after injection there was a tendency for venom and albumin to concentrate in the stomach ( 3 rd h),small intestine (3 rd h) and large intestine (6th h). Both control groups had more radioactivity in the digestive tract, especially in the stomach, but these levels decreased essentially to baseline by 12-18 h postinjection. In the kidneys, the distribution profiles of venom, albumin and iodine were similar. Counts at 30 min postinjection were low in all three groups (1.37, 1.86 and 0.77, respectively), and diminished to essentially 0% by 12-18 h. Albumin tended to concentrate in muscle until the 3 rd h postinjection (1.98%).There was a low binding of labeled venom in the liver (B. erythromelas venom does not specifically target most internal organs. That is, the systemic effects of envenomation ar mainly due to an indirect action. (author)

  1. Dosimetry prior to I-131-therapy of benign thyroid disease

    International Nuclear Information System (INIS)

    The activity to be administered in I-131 therapy of benign thyroid disease is determined by the radiation absorbed dose necessary to cure the disease, the target mass, and the residence time of the I-131 in the target volume. Data from 73 patients with complete sets of uptake measurements 2, 6, 24, 48, and 96 (n = 53) or 120 (n = 20) hours after oral administration of 1 MBq I-131 were used to deduce residence times from subsets of 3, 2, or only 1 measurement for each individual. The values were compared to those obtained with the reference method, i.e. a fit of an uptake function based on a 2-compartment model to all 5 measurements, to quantify the errors introduced by the less demanding assessments. Deviations are less than 10% if the 2- compartment uptake function is fitted to only 3 values measured after 6, 24, and 96-120 h. Use of 2, 24, and 96-120 h data results in errors > 20% in individual patients. The effective half-lives as determined from 2 measurements after 24 and 96-120 h correlate well with those deduced from the reference method with larger deviations in individuals with slow iodine kinetics and late maximal uptake. Residence times determined from the 24 h uptake, assuming linear increase during the first day, and the effective half-life limited to maximum 8 days underestimate the actual values systematically in patients with long and short half-lives. These errors can be eliminated by a modification of the calculation method resulting in deviations less than 14% in all but one individual for this procedure. The accuracy of methods based on only one retention value increases with the time of measurement after the administration of I-131. While systematic errors up to a factor of two occur if the 24 h uptake is used for the estimate, deviations are less than 18% for measurements after 120 h. The results suggest that only one late uptake assessment warrants residence time estimates with an acceptable error. Given the high inherent uncertainties in the

  2. A new and simple method for separation of 131I from tellurium oxide using an activated charcoal column

    International Nuclear Information System (INIS)

    A simple method for separation of 131I from irradiated TeO2 is described. Initially Te was separated from the 131I by precipitation technique. 131I solution containing traces of Te was adsorbed on an activated charcoal. After sufficient washings with HCl and water, 131I was desorbed from charcoal with NaOH. The recovery of Te was 99%. Retention of 131I on charcoal was 100% and elution efficiency was 75-80%. (author)

  3. Sintered bentonite ceramics for the immobilization of cesium- and strontium-bearing radioactive waste

    Science.gov (United States)

    Ortega, Luis Humberto

    The Advanced Fuel Cycle Initiative (AFCI) is a Department of Energy (DOE) program, that has been investigating technologies to improve fuel cycle sustainability and proliferation resistance. One of the program's goals is to reduce the amount of radioactive waste requiring repository disposal. Cesium and strontium are two primary heat sources during the first 300 years of spent nuclear fuel's decay, specifically isotopes Cs-137 and Sr-90. Removal of these isotopes from spent nuclear fuel will reduce the activity of the bulk spent fuel, reducing the heat given off by the waste. Once the cesium and strontium are separated from the bulk of the spent nuclear fuel, the isotopes must be immobilized. This study is focused on a method to immobilize a cesium- and strontium-bearing radioactive liquid waste stream. While there are various schemes to remove these isotopes from spent fuel, this study has focused on a nitric acid based liquid waste. The waste liquid was mixed with the bentonite, dried then sintered. To be effective sintering temperatures from 1100 to 1200°C were required, and waste concentrations must be at least 25 wt%. The product is a leach resistant ceramic solid with the waste elements embedded within alumino-silicates and a silicon rich phase. The cesium is primarily incorporated into pollucite and the strontium into a monoclinic feldspar. The simulated waste was prepared from nitrate salts of stable ions. These ions were limited to cesium, strontium, barium and rubidium. Barium and rubidium will be co-extracted during separation due to similar chemical properties to cesium and strontium. The waste liquid was added to the bentonite clay incrementally with drying steps between each addition. The dry powder was pressed and then sintered at various temperatures. The maximum loading tested is 32 wt. percent waste, which refers to 13.9 wt. percent cesium, 12.2 wt. percent barium, 4.1 wt. percent strontium, and 2.0 wt. percent rubidium. Lower loadings of waste

  4. I-131 remnant ablation after thyroidectomy induced hepatotoxicity in a case of thyroid cancer

    OpenAIRE

    Lin, Rong; Banafea, Omar; Ye, Jin

    2015-01-01

    Background Radioactive iodine (I-131) is routinely used for the treatment of differentiated thyroid cancer following surgery. Drug-induced liver injury (DILI) is a leading cause of acute liver failure. Here we reported a rare case of diffuse hepatic uptake (DHU) of radioactive iodine (I-131) induced hepatotoxicity in patient with I-131 ablation therapy after thyroidectomy. Case presentation A 57-year-old woman was admitted due to jaundice, itching and dark urine with abnormally elevated liver...

  5. Transient cytotoxicity of 131I beta radiation in hyperthyroid patients treated with radioactive iodine

    OpenAIRE

    Sundaram, P. Shanmuga; Padma, S.; Sudha, S.; Sasikala, K.

    2011-01-01

    Background & objectives: Radioiodine (131I) or radioactive iodine in low doses is used worldwide as the first line of management in the treatment of hyperthyroidism. Information is available on the extent and severity of cell damage after a high dose radioiodine (131I) therapy for thyroid cancer, but information is scanty on its cellular effects, its extent and severity of cell damage after a low dose 131I therapy. The present investigation was aimed to study the cytotoxic effects of a low do...

  6. Use of gamma probe in 131I thyroid uptake studies

    International Nuclear Information System (INIS)

    Evaluation of thyroid uptake by administration of radioactive iodine is a well-defined procedure to assess patient thyroid function. In general, nuclear medicine institutions use gamma cameras coupled to pinhole collimators to perform uptake studies. With the growing use of intraoperative gamma probes in the radioguided surgical techniques, several institutions are purchasing this new and portable equipment, which can technically be also employed to assess patient's thyroid function, permitting further other applications of gamma cameras. The aim of the study was to compare thyroid uptake trails carried out with both gamma camera and intraoperative gamma probe, in order to evaluate the possible use of gamma probe for this purpose. At first a preliminary study of feasibility was carried out using a neck phantom to verify equipment efficiency with known activities of 131 I. Henceforth, work data from 12 patients undergone studies of thyroid uptakes were evaluated, 24 hours after oral administration of 370 kBq of 131 I. The maximum difference observed between the values obtained with both equipment was 60%, which demonstrated the feasibility of the proposed protocol and made clear that gamma probe can be useful for thyroid uptake studies. (author)

  7. Effect of 131I on the anemia of hyperthyroidism

    Energy Technology Data Exchange (ETDEWEB)

    Perlman, J.A.; Sternthal, P.M.

    1983-01-01

    Data from the National Thyrotoxicosis Therapy Follow-Up Study (NTTFS) are presented here to document the existence of anemia in hyperthyroidism, a mild and reversible anemia that is simultaneously ameliorated with reversal of the hyperthyroid state. Among 20,600 women entered into the NTTF study with no previous history of hematological disorders, the prevalence of anemia was found to range from 10-15%, appearing to be higher in those selected for treatment with 131I when compared to those selected for surgery. An attempt is made to verify the recent hypothesis that thyroid hormone levels in the supraphysiologic range may suppress erythrogenesis. Two statistically significant regression models are consistent with a hypothesis of thyrotoxic bone marrow suppression. However, both associations are weak enough to suggest that some other physiologic improvement underlies the amelioration of anemia when hyperthyroidism is reversed. The degree of improvement in hematological status is similar for women in both treatment groups. Among 4464 women for whom serial hematological tests are obtained, over 3/4 of anemic patients are no longer anemic after an average 6.2 yr of follow-up. Clinicians are reassured that radioactive iodine exposure causes no further insult to the bone marrow, no matter what the cumulative dosage. The highly fractionated low dose bone marrow exposures to radiation account for the minimal hematological risks of 131I treatment.

  8. Diagnosis of pheochromocytome by 131-I-MIBG

    International Nuclear Information System (INIS)

    The purpose of this project is to evaluate the specificity and sensitivity of 131-I-metaiodobenzylguanidine (MIBG), a newly developed radiopharmaceutical which accumulated in the neuro transmitter adrenergic sacs, in diagnosing pheochromocytomes, which originate from well-differentiated cells in the adrenergic region of the autonomous nervous system. A sizeable number of these cells appear in the adrenal medulla, the para-spinal ganglion and the para-aortic (Organ of Zuckerkandl), however, a certain number of pheochromocytomes are found in other sites including the bladder, heart and vagus nerves. Adrenergic tumors which are located outside the adrenal medulla and which secrete both norepinephrine and epinephrine are called pheochromocytomes. Scintigraphic distribution of 131-I-MIBG, an imaging agent for the adrenal medulla, was studied to determine the uptake in patients suspected of harboring pheochromocytomes. Normal distribution of the radiotracer includes: the salivary glands, liver, spleen, gall-bladder, kidneys and heart. Accumulations in the thyroids are detected only in cases of inadequate thyroid blocking. Injected were 0.5 mCi/1.7 m2 and scans taken 24, 48 and 72 hours afterward. The five patients investigated showed high levels of epinephrine and norepinephrine and revealed abnormal accumulations of radioactive material. These data were surgically verified. (author)

  9. Treatment of malignant pheochromocytomas with 131-I-Metaiodobenzylguanidine

    Energy Technology Data Exchange (ETDEWEB)

    Charbonnel, B.; Chatal, J.F.; Brendel, A.J.; Marchandise, X.; Wemeau, J.L.; Lanehche, B.; Mornex, R.; Lumbroso, J.; Schlumberger, M.

    1988-01-01

    Twelve patients (2 with only bone metastases, 3 with only soft tissues metastases and 7 with bone and soft tissues metastases) were treated with 131-I -MIBG (specific activity: 20 mCi/mg), 100 to 200 mCi every 3-6 months. A dosimetric study was carried out before each administration. The follow-up ranged from 6 to 24 months and the number of doses ranged from 1 to 8, with 1.85-9 GBq per administration and a cumulative activity of 1.85-62.2 GBq according to patients. The cumulative absorbed activity ranged from 850 to 9700cGy. The following side effects were observed: a bone marrow hypoplasia (1 patient) and a transient increase in catecholamines (3 patients). The treatment was successfull in 7 patients (3 with soft tissue metastases, 3 with bone and soft tissue metastases and one with bone metastases). This success consisted in clinical improvement and a decrease > 50% of hormonal values in the 7 patients and a decrease > 50% of tumoral masses in only 3 patients. No complete remission was obtained at this stage of the study. The disease recurred in 1 patient after a year of partial remission. There was no clear-cut relation between the number of doses and the results. This study shows that 131-I-MIBG can give encouraging though limited results.

  10. Differential expression profiling of circulation microRNAs in PTC patients with non-131I and 131I-avid lungs metastases: a pilot study

    International Nuclear Information System (INIS)

    Introduction: Loss of the ability to concentrate 131I is one of the important causes of radioiodine-refractory disease in papillary thyroid carcinoma (PTC). Recent advantages of serum microRNAs (miRNAs) open a new realm of possibilities for noninvasive diagnosis and prognosis of many cancers. The aim of the current study was to identify differential expression profiling of circulation miRNAs in PTC patients with non-131I and 131I-avid lungs metastases. Methods: The expressions of miRNAs were examined using miRNA microarray chip. The most significantly changed miRNAs from microarray were verified by using qRT-PCR. The potential miRNAs regulating target genes and their preliminary biological functions were forecasted by Bioinformatic analysis. Results: Compared to 131I-avid lung metastases, 13 kinds of significantly differential serum miRNAs including 5 upregulated miRNAs (miR-1249, miR-106a, miR-503, miR-34c-5p, miR-1281) and 8 downregulated miRNAs (miR-1915, miR-2861, miR-3196, miR-500, miR-572, miR-33b, miR-554, miR-18a) in PTC patients with non-131 I-avid lung metastases were identified. Bioinformatic analysis demonstrated that miR-106a was the core miRNA regulating 193 genes in the network. The results of validation confirmed the up-regulation of miR-106a in non-131I-avid lungs metastatic PTC patients. Conclusion: Differentially expressed serum miRNA profiles between PTC patients with non-131I and 131I-avid lungs metastases were analyzed. These findings in our present study could represent new clues for the diagnostic and therapeutic strategy in PTC patients with non-131I-avid metastatic disease

  11. Direct in vivo injection of ~(131)I-GMS and its distribution and excretion in rabbit

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    AIM: To explore the distribution and metabolism of 131 I-gelatin microspheres ( 131 I-GMSs) in rabbits after direct injection into rabbits’ livers.METHODS: Twenty-eight healthy New Zealand rabbits were divided into seven groups,with four rabbits per group.Each rabbit’s hepatic lobes were directly injected with 41.336 ± 5.106 MBq 131 I-GMSs.Each day after 131 I-GMSs administration,4 rabbits were randomly selected,and 250 μL of serum was collected for γ count.Hepatic and thyroid functions were tested on days ...

  12. Detection of experimentally produced acute pulmonary arterial occlusion by methyl iodide-131 inhalation imaging

    International Nuclear Information System (INIS)

    Methyl iodide-131 (CH3I-131) is described as an agent for detection of acute experimentally produced pulmonary arterial occlusion in dogs. When gaseous CH3I-131 is inhaled, radioactivity passes instantaneously from the alveoli to the lung capillary bed. Where pulmonary blood flow exists, activity is washed out into the systemic circulation, but in areas of blood stasis, a transient pulmonary hot spot remains. CH3I-131 is easily produced and inexpensive, but administration is awkward and strict radiation safety precautions are mandatory

  13. Bioassay program: determination of I-131 body burden among radiation workers and nuclear medicine laboratory technicians

    Energy Technology Data Exchange (ETDEWEB)

    Duran, E.B.; Napenas, D.; San Jose, V.; Juan, N.

    The body burden of I-131 was determined among the radiation workers of the Philippine Atomic Energy Commission (PAEC) who are directly involved in I-131 processing and nuclear laboratory technicians of University of Santo Tomas and Veterans Hospital, who handle and dispense I-131 to patients. The routine monitoring was done by urine analysis. The untreated urine samples were counted directly for 4000 seconds using Nal(Tl) scintillation detector coupled to an ND66 microcomputer-based multichannel analyzer. Urine samples of radiation workers of PAEC who are not involved in I-131 processing and non-radiation workers were also assayed for comparison. For radiation workers of PAEC who are directly involved in processing I-131, the estimated body burden of I-131 ranged from <0.055 to 8.53 uCi (282 urine samples). These values were higher than those observed for radiation workers not involved in the handling or processing of I-131 with estimated body burden of I-131 ranging from <0.055 to 0.52 uCi (48 urine samples) or than those observed from non-radiation workers (<0.055 uCi). The maximum permissible burden of I-131 is 0.7 uCi.

  14. Iodine-131 uptake and transfer from soil to rice following factitious contaminations

    International Nuclear Information System (INIS)

    An investigation was carried out to determine iodine-131 uptake and transfer factor (TF) in pot-grown rice ('IR 20') with three soils of different texture, viz., a sandy clay loam, a sandy loam, and a sandy soil. The soils were factitiously contaminated with four levels of 131I: 20, 40, 60, and 80 kBq kg-1 of soil. Soil texture greatly influenced biomass yield, 131I uptake and TF in rice. The effect of level of 131I was significant only in the case of grain. In the case of straw, neither the 131I content nor uptake were influenced by the variables. The 131I uptake by grain appeared to increase with the level of 131I contamination. The highest uptake was at the highest level of 131I contamination and in the sandy loam soil. The TF values in all plant parts decreased significantly with the 131I contamination levels and were lowest, quite interestingly, in the sandy clay loam soil for root and in the sandy soil for grain. The TFs followed the order: root > straw > grain. (author)

  15. A study of mechanisms responsible for incorporation of cesium and radiocesium into fruitbodies of king oyster mushroom (Pleurotus eryngii)

    Energy Technology Data Exchange (ETDEWEB)

    Bystrzejewska-Piotrowska, Grazyna [Isotope Laboratory, Faculty of Biology, Warsaw University, 02-096 Warsaw, Miecznikowa 1 (Poland)], E-mail: byst@biol.uw.edu.pl; Bazala, Michal A. [Isotope Laboratory, Faculty of Biology, Warsaw University, 02-096 Warsaw, Miecznikowa 1 (Poland)

    2008-07-15

    Ex vitro cultures of Pleurotus eryngii were carried out under controlled conditions using sterile medium composed of barley seeds. The influence of alkali and alkaline earth element salts (CsCl, KCl, NaCl, RbCl, and CaCl{sub 2}) and tetraethylammonium chloride on incorporation of cesium, potassium, sodium, rubidium and calcium, and their distribution within fruitbodies, was examined. The results show that incorporation of cesium into fruitbodies was not suppressed by Na{sup +} and Rb{sup +} or tetraethylammonium chloride. However, it was inhibited by Ca{sup 2+} and stimulated by high concentrations of K{sup +}. The inhibition of cesium incorporation by Ca{sup 2+}, lack of influence of tetraethylammonium chloride and stimulation by high K{sup +} concentrations suggest that there may exist two pathways of passive transport of cesium in mycelium: (i) uptake mediated by a non-specific potassium channel localised in plasmalemma (similar to voltage-insensitive cation channel, VICC) followed by diffusive transport inside hyphae and (ii) extracellular transport from the medium through inter-hyphal cavities into fruitbodies. The results highlight distinctiveness of mechanisms responsible for the uptake and incorporation of cesium in mushrooms and plants.

  16. A tentative assessment of cesium 137 direct and indirect transfer rates in a simplified fresh water food chain

    International Nuclear Information System (INIS)

    A comparison was made of the direct transfer of cesium from water to carps and the indirect transfer via the food. In a first experiment on chronic contamination of carps by water, the kinetics and distribution of cesium in the organs of the carps were studied. Equilibrium was not reached on the 56th day, 4% of the initial water activity had been retained by the carps and the concentration factor was below 10. The highest specific activities were found in the transit organs. In a second experiment, the water activity varied by alternating contamination and decontamination. A fluctuating equilibrium was reached on the 22nd day. The concentration factor was of the same order of magnitude than in the previous experiment. Indirect contamination of fish by ingestion of contaminated daphnids was studied in a third experiment. Cesium levels in carps increased with the cumulated activities in meals, and the uptake rate in fish was 4%. Both decorporation and biological half-lives (30-40 days) were independent of the contamination routes. The respective significance of the transfer pathways is discussed taking into account the biomass pyramids to be found in the nature. It is estimated that in a cesium environment, 70% of the carp activity should come from the diet and 30% from the water. The concentration factor would then be 75 instead of 22 when only direct transfer of cesium from water to fish is considered

  17. Kinetics of iodine and cesium reactions in the CANDU reactor primary heat transport system under accident conditions

    International Nuclear Information System (INIS)

    Gas-phase reaction kinetics have been modelled for the release of cesium and iodine into steam and steam/hydrogen atmospheres. The conditions are those anticipated in a CANDU reactor fuel channel following some postulated loss-of-coolant accidents. A total of seventeen chemical species were used in the model, including all important cesium and iodine species. Reaction rate constants were taken from the literature, or calculated where possible, or estimated. The composition evolution of the system was calculated, following a burst release of cesium and iodine, as a function of total iodine and cesium concentrations, cesium/iodine release ratio, iodine release form (atomic I or CsI), fuel channel atmosphere, and radiolysis effects. In general, the calculation demonstrates that CsI and CsOH rapidly (-2 s) become the most important species in the system for virtually all conditions. Atomic I is found to be significant only for very low release concentrations, or for Cs:I ratios less than unity. The main body of the modelling was performed at 1000 K. Some calculations were also performed for a three-node temperature system - 1500 K, 1000 K and 750 K - with the fission products being transported from high to low temperature. Thus, a qualitative picture is provided of the evolution of the chemistry in the fuel channel as the fission products are swept out by the residual steam flow

  18. Removal of radioactive cesium, strontium, and iodine from natural waters using bentonite, zeolite, and activated carbon

    International Nuclear Information System (INIS)

    Cs-134, Sr-85, and I-131 were produced by neutron irradiation of CsCl, SrCl2, and K2TeO3, respectively, using the Kyoto University Reactor. These radioactive nuclides were added to river water and seawater to prepare artificially contaminated samples, and the removal of these nuclides using bentonite, zeolite, and activated carbon was then investigated. In the river water samples, Cs-134 and Sr-85 were successfully removed using bentonite and zeolite, and I-131 was removed using activated carbon. In the seawater samples, Cs-134 was removed using bentonite and zeolite, whereas Sr-85 and I-131 were hardly removed at all by these adsorbents. (author)

  19. Behavior of medically-derived 131I in the tidal Potomac River

    International Nuclear Information System (INIS)

    Iodine-131 (t1/2 = 8.04 d) is administered to patients for treatment of thyroid disorders, excreted by patients and discharged to surface waters via sewage effluent. Radionuclides generally behave like their stable analogs; therefore, medically-derived 131I is useful as a transport-reaction tracer of anthropogenic inputs and the aquatic biogeochemistry of iodine. Iodine-131 was measured in Potomac River water and sediments in the vicinity of the Blue Plains Water Pollution Control Plant (WPCP), Washington, DC, USA. Concentrations measured in sewage effluent from Blue Plains WPCP and in the Potomac River suggest a relatively continuous source of this radionuclide. The range of 131I concentrations detected in surface water was 0.076 ± 0.006 to 6.07 ± 0.07 Bq L−1. Iodine-131 concentrations in sediments ranged from 1.3 ± 0.8 to 117 ± 2 Bq kg−1 dry weight. Partitioning in the sewage effluent from Blue Plains and in surface waters indicated that 131I is associated with colloidal and particulate organic material. The behavior of medically-derived 131I in the Potomac River is consistent with the nutrient-like behavior of natural iodine in aquatic environments. After discharge to the river via sewage effluent, it is incorporated into biogenic particulate material and deposited in sediments. Solid phase sediment profiles of 131I indicated rapid mixing or sedimentation of particulate debris and diagenetic remineralization and recycling on short time scales. - Highlights: ► Medically-derived 131I was measured in sewage effluent, river water, and sediments. ► Sediment 210Pb and 7Be profiles help characterize the sedimentary environment. ► 131I flux to sediments in study area is ∼ 1% of that discharged in sewage effluent. ► 131I distributions constrain reaction-transport processes to weekly time scales. ► Collectively these data are used to better understand iodine biogeochemistry

  20. Cesium accumulation by bacterium Thermus sp.TibetanG7: hints for biomineralization of cesiumbearing geyserite in hot springs in Tibet, China

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The bacterium Thermus sp. TibetanG7, isolated from hot springs in Tibet, China, was examined for the ability to accumulate cesium from solutions. Environmental conditions were simulated and the effects of pH, K+, Na+ and K+-regimes were then studied to determine the possible role of the bacterium in the formation of cesium-bearing geyserite around these hot springs. In despite of the inhibition of K+ and Na+, the bacterium Thermus sp. TibetanG7 revealed noticeable accumulation of cesium from solutions, with maximum accumulations of 53.49 and 40.41 μmol Cesium/g cell dry weight in Na+ and K+ inhibition experiments, respectively. The accumulation of cesium by this microorganism is rapid, with 40%―50% accumulated within the first 5 min. K+-deficient cells showed a much higher capacity of cesium accumulation compared with K+-sufficient cells. It is evident that the bacteria within the genus thermus play a significant role in the cesium assembly. The formation of cesium-bearing geyserite is also considered.

  1. 131I治疗对Graves眼病转归的影响%Effect of 131I therapy on outcomes of Graves' ophthalmopathy

    Institute of Scientific and Technical Information of China (English)

    王任飞; 谭建; 张桂芝; 尹亮

    2011-01-01

    目的 分析131I治疗后Graves甲状腺功能亢进症(甲亢)疗效与Graves眼病转归的相关关系,探讨131I治疗对Graves眼病转归的影响.方法 652例Graves甲亢合并Graves眼病的患者,均按照常规程序一次性给予治疗量的131I.服用131I前测量患者眼球突出度,并详细记录眼部症状和特征.治疗结束后定期随访,评价疗效.结果 患者服用131I后Graves甲亢治疗的总有效率约为94.3%,Graves眼病的总好转率约为73.3%,而Graves甲亢及Graves眼病治疗均有效者约占总病例数的71.2%.131I治疗后Graves眼病的转归与Graves甲亢是否得到有效缓解具有明显的相关性(r=0.302,P<0.05).131I治疗后Graves甲亢治愈组与甲状腺功能减退症(甲减)组比较,Graves眼病的疗效差异无统计学意义(x2=0.296,P>0.05).结论 通过131I治疗来缓解Graves甲亢是控制Graves眼病的根本措施.患者服用131I后加强随访,及时发现和纠正甲减可有效避免Graves眼病的加重.%Objective To analyze the correlation between the therapeutic effect of Graves'hyperthyroidism and the outcomes of Graves' ophthalmopathy after 131I therapy,and to explore the effect of 131I treatment on turnout of Graves' ophthalmopathy.Methods Six hundreds and fifty-two patients of Graves' disease accompanied with Graves' ophthalmopathy,received one-time 131I treatment according to routine procedure.We recorded exophthalmometer readings,the signs and symptoms of eyes before therapy.Regular follow-up and appraisal of curative effect were carried out.Results At least six months after 131Itherapy,the effective rate of Graves' hyperthyroidism and Graves' ophthalmopathy were 94.3% and 73.3%respectively.The total effective rate of hyperthyroidism with ophthalmophy was 71.2%.There was a significant correlation between the prognosis of Graves' ophthalmopathy and therapeutic efficacy of hyperthyroidism (r=0.302,P<0.05).The outcomes of Graves' ophthalmopathy had no

  2. A new alternative for the decontamination of PWR primary circuits for radioactive cesium and silver by insoluble ferrocyanides

    International Nuclear Information System (INIS)

    The optimal recovery conditions of radioactive cesium and silver from PWR primary circuits were determined on two types of nickel and zinc ferrocyanides. The studied products have been prepared by a slow growth on solid alkaline ferrocyanide particles placed in a concentrated nickel or zinc salt solution. Columns of these products do not react with water or lithium borate solutions as well as with organic solvents. The decontamination factor for cesium or silver is over 1000 for synthetic solutions. The presence of other alkaline ions does not modify these results. In the case of nuclear liquid wastes, the decontamination remains high for cesium. Silver is retained with a good efficiency if it is not under a complex form. This complex is destroyed by acidification. The setting of concrete is not significantly modified by the presence of ferrocyanides. The drawback of this method is a slight elution of some cations composing the ferrocyanides

  3. Ion exchange removal of cesium from simulated and actual supernate from Hanford tanks 241-SY-101 and 241-SY-103

    International Nuclear Information System (INIS)

    Pacific Northwest Laboratory (PNL), in conjunction with the Process Chemistry and Statistics Section of Westinghouse Hanford Company (WHC), conducted this study as part of the Supernatant Treatment Development Task for the Initial Pretreatment Module (IPM) Applied Engineering Project. The study assesses the performance of the CS-100 ion exchange material for removing cesium from simulated and actual alkaline supernate from Hanford tanks 241-SY-101 and 241-SY-103. The objective of these experiments is to compare the cesium ion exchange loading and elution profiles of actual and simulated wastes. Specific experimental objectives include (1) demonstration of decontamination factors (DF) for cesium removal, 92) verification of simulant performance, (3) investigation of waste/exchanger chemistry, and (4) determination of the radionuclide content of the regenerated CS-100 resin prior to disposal

  4. Effects of potassium and nitrogen groundwater pollution on the migration of cesium-137 through the geological environment

    International Nuclear Information System (INIS)

    Effects of potassium and nitrogen groundwater pollution on the migration of cesium-137 through the geological environment were studied for the territories of Russia, Ukraine, Belarus. Migration rate of cesium-137 deposited as a result of the Chernobyl accident increases in geologic media (soils, rocks, and groundwater) polluted by potassium and ammonium originating from long-term fertilizers use. This effect manifests itself in the fact that radiocesium penetrates deeper into soils of arable lands than it does into virgin soils. Laboratory experiments show the sorption capacity of sandy soils with respect to cesium-137 is 2.5-9.2 times lower in the presence of solutions of chlorides and nitrates of potassium and ammonium and is 1.3-2.0 times lower in the presence of sodium nitrate solution. 26 refs.; 2 figs

  5. Simulation of cesium nitrate extraction by a calixarene. Application to supported liquid membranes transport

    International Nuclear Information System (INIS)

    This work fits into the general pattern of the CEA studies on the decontamination of liquid effluents containing long-lived radioactive isotopes. Some calixarenes have proved to be very effective to selectively extract the cesium of aqueous solutions whose composition simulates those of the effluents to be reprocessed. On account of the difficulty of the studied extraction mechanisms, a physical and chemical simulation has been necessary. The system takes into account: 1)a concentrated nitric acid aqueous phase and/or sodium nitrate 2)an organic phase constituted by the diluent 1,2-nitro-phenyl-octyl-ether and 1,3-diisopropoxy-calix(4)arene-couronne-6. The use of concentrated aqueous solutions requires to take into account variations to ideality by the mean of activity coefficients reckoning. The different theories on the reckoning of variations to ideality in aqueous or organic phases are described in the first part. The determination of cesium and sodium nitrates activity coefficients in very concentrated matrices has required an important theoretical and experimental study which is given in the second part. The aim of this study was indeed to complete the thermodynamic data of cesium and sodium nitrates aqueous solutions. The computerized tools required for the modeling are reviewed. The stoichiometry of the extracted species in the organic phase has been determined in the third part. The supported membrane technique is an original method of separation by liquid-liquid extraction. A membrane transport model has been developed and is given in the last part of this work. (O.M.)

  6. Al-free active region laser diodes at 894 nm for compact Cesium atomic clocks

    Science.gov (United States)

    Von Bandel, N.; Bébé Manga Lobé, J.; Garcia, M.; Larrue, A.; Robert, Y.; Vinet, E.; Lecomte, M.; Drisse, O.; Parillaud, O.; Krakowski, M.

    2015-03-01

    Time-frequency applications are in need of high accuracy and high stability clocks. Compact industrial Cesium atomic clocks optically pumped is a promising area that could satisfy these demands. However, the stability of these clocks relies, among others, on the performances of laser diodes that are used for atomic pumping. This issue has led the III-V Lab to commit to the European Euripides-LAMA project that aims to provide competitive compact optical Cesium clocks for earth applications. This work will provide key experience for further space technology qualification. We are in charge of the design, fabrication and reliability of Distributed-Feedback diodes (DFB) at 894nm (D1 line of Cesium) and 852nm (D2 line). The use of D1 line for pumping will provide simplified clock architecture compared to D2 line pumping thanks to simpler atomic transitions and larger spectral separation between lines in the 894nm case. Also, D1 line pumping overcomes the issue of unpumped "dark states" that occur with D2 line. The modules should provide narrow linewidth (<1MHz), very good reliability in time and, crucially, be insensitive to optical feedback. The development of the 894nm wavelength is grounded on our previous results for 852nm DFB. Thus, we show our first results from Al-free active region with InGaAsP quantum well broad-area lasers (100μm width, with lengths ranging from 2mm to 4mm), for further DFB operation at 894nm. We obtained low internal losses below 2cm-1, the external differential efficiency is 0.49W/A with uncoated facets and a low threshold current density of 190A/cm², for 2mm lasers at 20°C.

  7. Use of cesium-137 methodology in the evaluation of superficial erosive processes

    Directory of Open Access Journals (Sweden)

    Avacir Casanova Andrello

    2003-06-01

    Full Text Available Superficial erosion is one of the main soil degradation agents and erosion rates estimations for different edaphicclimate conditions for the conventional models, as USLE and RUSLE, are expensive and time-consuming. The use of cesium-137 antrophogenic radionuclide is a new methodology that has been much studied and its application in the erosion soil evaluation has grown in countries as USA, UK, Australia and others. A brief narration of this methodology is being presented, as the development of the equations utilized for the erosion rates quantification through the cesium-137 measurements. Two watersheds studied in Brazil have shown that the cesium-137 methodology was practicable and coherent with the survey in field for applications in erosion studies.A erosão superficial é um dos principais agentes de degradação dos solos e estimativas das taxas de erosão para diferentes condições edafoclimáticas pelos modelos tradicionais como USLE, RUSLE, são onerosos e demorados. Uma metodologia que tem sido muito estudada e sua aplicação no estudo da erosão vem crescendo em países como EUA, Reino Unido, Austrália, e outros, é a do uso do radionuclídeo antropogênico césio-137. Um resumo da história desta metodologia é apresentado, assim como a evolução das equações utilizadas para quantificar as taxas de erosão através da medida do césio-137. Duas bacias estudadas no Brasil mostraram que a metodologia do césio-137 é viável e coerente com as observações em campo para aplicação no estudo da erosão.

  8. Distribution of global fallouts cesium-137 in taiga and tundra catenae at the Ob River basin

    Science.gov (United States)

    Semenkov, I. N.; Usacheva, A. A.; Miroshnikov, A. Yu.

    2015-03-01

    The classification of soil catenae at the Ob River basin is developed and applied. This classification reflects the diverse geochemical conditions that led to the formation of certain soil bodies, their combinations and the migration fields of chemical elements. The soil and geochemical diversity of the Ob River basin catenae was analyzed. The vertical and lateral distribution of global fallouts cesium-137 was studied using the example of the four most common catenae types in Western Siberia tundra and taiga. In landscapes of dwarf birches and dark coniferous forests on gleysols, cryosols, podzols, and cryic-stagnosols, the highest 137Cs activity density and specific activity are characteristic of the upper soil layer of over 30% ash, while the moss-grass-shrub cover is characterized by low 137Cs activity density and specific activity. In landscapes of dwarf birches and pine woods on podzols, the maximum specific activity of cesium-137 is typical for moss-grass-shrub cover, while the maximum reserves are concentrated in the upper soil layer of over 30% ash. Bog landscapes and moss-grass-shrub cover are characterized by a minimum activity of 137Cs, and its reserves in soil generally decrease exponentially with depth. The cesium-137 penetration depth increases in oligotrophic histosols from northern to middle taiga landscapes from 10-15 to 40 cm. 137Cs is accumulated in oligotrophic histosols for increases in pH from 3.3 to 4.0 and in concretionary interlayers of pisoplinthic-cryic-histic-stagnosols. Cryogenic movement, on the one hand, leads to burying organic layers enriched in 137Cs and, on the other hand, to deducing specific activity when mixed with low-active material from lower soil layers.

  9. Meta-iodobenzylguanidine synthesis and labelling with iodine-131

    International Nuclear Information System (INIS)

    Meta-iodo-benzylguanidine (MIBG) synthesis is carried out through m-iodo benzylamine condensation and subsequent formation of the hemisulfate salt. The synthesized product is characterized and identified by IR spectroscopy and m.p. determination. Acute toxicity tests conducted in mice demonstrated that the synthesized product is not toxic. MIBG hemisulfate labelling methods with I-131 is carried out by nucleophilic isotopic exchange; the reaction is catalyzed with cooper sulfate in the presence of ammonium sulfate at temperatures ranging between 140 and 150 oC . Biological distribution tests in wistar rats present an average value of 1,54% of injected dose/organ gram in suprarenal glands. These values show promise for the application of this radiopharmaceutical in radiodiagnosis of suprarenal tumors and procurement of adrenal medulla, myocardium and salivary gland images

  10. Airborne release of 131I associated with patient therapy

    International Nuclear Information System (INIS)

    Airborne concentrations of Iodine-131 were measured following oral administration of therapeutic doses to hospitalized patients. Administered doses ranged from 10 to 200 mCi. Air samples were obtained using activated charcoal collectors and analyzed by gamma-ray counting techniques. Results of a preliminary study indicated the presence of air concentrations in excess of the RCG in air up to 10 hours following administration. Airborne concentrations followed a two-component exponential clearance function with effective half times of ∼ 0.5 and ∼ 13 hours. The respective components are thought to originate from the initial administration procedure and subsequent excretion of iodine from the patient. In addition, the results show that activity may be released during the initial opening of the therapy dose. Assessments of the internal exposure of hospital personnel and the relative hazards from administration of liquid or capsular doses are made. Sources of release of iodine to the atmosphere from the patient are considered. (author)

  11. Sleep wake pattern analysis: Study of 131 medical students

    Directory of Open Access Journals (Sweden)

    Nita Ninama

    2012-07-01

    Full Text Available Objective:Sleep is part of the rhythm of life. Without a good sleep the mind is less adapts, mood is altered and the body loses the ability to refresh. The sleep wake cycle of the students is quite different and characterized by delayed onset, partial sleep deprivation, poor sleep quality, insufficient sleep duration and occurrence of napping episodes during the day The aim of the present study is to know sleep wake pattern in medical student, role of residence and individual characterization on sleep wake cycle.Design:Cross sectional Study. Participants:There are 131 first year medical students of the Smt. NHL Municipal Medical College.Measurements and Results:All the students answered the Portuguese version of the Horne & Östberg Morningness and Eveningness questionnaire, the Pittsburgh sleep quality index (PSQI and kept a sleep diary for two weeks.We analyzed 131 students, 51 residing at hostel and 80 residing at home, with mean PSQI 6.55 and 7.48 respectively (PSQI >5 = poor sleep quality. Sleep diary analysis of morning and evening type group shows delayed sleep onset in later group (23.45 ± 1.14 vs. 1.15 ± 0.50 hrs. We also found reduced sleep duration during weekdays and extended sleep duration during weekends in evening type students and vice-a-versa in morning type of students.Conclusion:We found poor sleep quality in medical student irrespective of residence. Poor sleep quality and sleep deprivation is more pronounced in evening type of the students and partial compensation found on weekends. Morning type students adjust their life better than evening type and manage their academic schedule.

  12. A major technological accident: the dispersion of a radioactive cesium - 137 pellet in Goiania, Brazil (1987)

    International Nuclear Information System (INIS)

    This study concerns the accidental dispersion of cesium 137 chloride via an abandoned radiotherapy device in Brazil, in september 1987. Since the accident occurred recently in a confined area and concerned a single radiochemical agent, it was possible to delimit the study parameters in each discipline: post-accident management, physics, medicine, environment, law, psychology, socio-economics and communication. Costs are difficult to evaluate but obviously very important. It is difficult to analyze all consequences. No official has been accused, there were no sentence. The results demonstrate the critical importance of the human factor in technological accidents. (A.L.B.)

  13. High-Pressure Low-Symmetry Phases of Cesium Halides from First Principle Techniques

    OpenAIRE

    Nardelli, M. Buongiorno; Baroni, S.; Giannozzi, P.

    1994-01-01

    The relative stability of different high-pressure phases of various Cesium Halides is studied from first principles and analyzed using the Landau theory of phase transitions. We present results for CsI, CsBr, and CsCl up to pressures of about 100 GPa. A cubic-to-orthorhombic transition, driven by the softening of an acoustic phonon at the M point of the Brillouin zone, is competing with the cubic-to-tetragonal martensitic transition typical of these compounds. The phonon softening takes place...

  14. Carbon, cesium and iodine isotopes in Japanese cedar leaves from Iwaki, Fukushima

    DEFF Research Database (Denmark)

    Xu, Sheng; Cook, Gordon T.; Cresswell, Alan J.;

    2016-01-01

    Japanese cedar leaves from Iwaki, Fukushima were analyzed for carbon, cesium and iodine isotopic compositions before and after the 2011 nuclear accident. The Δ14C values reflect ambient atmospheric 14C concentrations during the year the leaves were sampled/defoliated, and also previous year......(s). The elevated 129I and 134,137Cs concentrations are attributed to direct exposure to the radioactive fallout for the pre-fallout-expended leaves and to internal translocation from older parts of the tree for post-fallout-expended leaves. 134Cs/137Cs and 129I/137Cs activity ratios suggest insignificant isotopic...

  15. Dynamic modeling of the cesium, strontium, and ruthenium transfer to grass and vegetables

    Energy Technology Data Exchange (ETDEWEB)

    Renaud, P.; Real, J.; Maubert, H.; Roussel-Debet, S. (CE de Cadarache, Saint-Paul lez Durance (France). Inst. de Protection et de Surete Nucleaire)

    1999-05-01

    From 1988 to 1993, the Nuclear Safety and Protection Institute (Institut de Protection et de Surete Nucleaire -- IPSN) conducted experimental programs focused on transfers to vegetation following accidental localized deposits of radioactive aerosols. In relation to vegetable crops (fruit, leaves, and root vegetables) and meadow grass these experiments have enabled a determination of the factors involved in the transfer of cesium, strontium, and ruthenium at successive harvests, or cuttings, in respect of various time lags after contamination. The dynamic modeling given by these results allows an evaluation of changes in the mass activity of vegetables and grass during the months following deposit. It constitutes part of the ASTRAL post-accident radioecology model.

  16. Cesium Enhances Long-Term Stability of Lead Bromide Perovskite-Based Solar Cells

    OpenAIRE

    Kulbak, Michael; Gupta, Satyajit; Kedem, Nir; Levine, Igal; Bendikov, Tatyana; Hodes, Gary; Cahen, David

    2015-01-01

    Direct comparison between perovskite-structured hybrid organic-inorganic - methyl ammonium lead bromide (MAPbBr3) and all-inorganic cesium lead bromide (CsPbBr3), allows identifying possible fundamental differences in their structural, thermal and electronic characteristics. Both materials possess a similar direct optical band-gap, but CsPbBr3 demonstrates a higher thermal stability than MAPbBr3. In order to compare device properties we fabricated solar cells, with similarly synthesized MAPbB...

  17. Optical and evaporative cooling of cesium atoms in the gravito-optical surface trap

    CERN Document Server

    Hammes, M; Druzhinina, V; Moslener, U; Manek-Hönninger, I; Grimm, R

    2000-01-01

    We report on cooling of an atomic cesium gas closely above an evanescent-wave atom mirror. At high densitities, optical cooling based on inelastic reflections is found to be limited by a density-dependent excess temperature and trap loss due to ultracold collisions involving repulsive molecular states. Nevertheless, very good starting conditions for subsequent evaporative cooling are obtained. Our first evaporation experiments show a temperature reduction from 10muK down to 300nK along with a gain in phase-space density of almost two orders of magnitude.

  18. Accumulation of uranium, cesium, and radium by microbial cells: bench-scale studies

    International Nuclear Information System (INIS)

    This report describes bench-scale studies on the utilization of microbial cells for the concentration and removal of uranium, radium, and cesium from nuclear processing waste streams. Included are studies aimed at elucidating the basic mechanism of uranium uptake, process development efforts for the use of a combined denitrification-uranium removal process to treat a specific nuclear processing waste stream, and a preliminary investigation of the applicability of microorganisms for the removal of 137Cs and 226Ra from existing waste solutions

  19. Systematically investigating the polarization gradient cooling in an optical molasses of ultracold cesium atoms

    Science.gov (United States)

    Ji, Zhong-Hua; Yuan, Jin-Peng; Zhao, Yan-Ting; Chang, Xue-Fang; Xiao, Lian-Tuan; Jia, Suo-Tang

    2014-11-01

    We systematically investigate the polarization gradient cooling (PGC) process in an optical molasses of ultracold cesium atoms. The SR mode for changing the cooling laser, which means that the cooling laser frequency is stepped to the setting value while its intensity is ramped, is found to be the best for the PGC, compared with other modes studied. We verify that the heating effect of the cold atoms, which appears when the cooling laser intensity is lower than the saturation intensity, arises from insufficient polarization gradient cooling. Finally, an exponential decay function with a statistical explanation is introduced to explain the dependence of the cold atom temperature on the PGC interaction time.

  20. Digital Square-Wave Frequency Modulated Microwave Sources for a Miniature Optically Pumped Cesium Beam Clock

    Institute of Scientific and Technical Information of China (English)

    CHEN Jingbiao; ZHU Chengjin; LIU Ge; WANG Fengzhi; WANG Yiqiu; YANG Donghai

    2001-01-01

    Three different digital frequencymodulated microwave sources have been designed andapplied to our miniature optically pumped cesiumbeam clock.The main features and their influenceon clock accuracy have been experimentally tested.Itis proved that a digital square-wave frequency modu-lated microwave source using a microprocessor con-trolled direct-digital frequency synthesizer (DDFS)for our miniature optically pumped cesium beamclock works well,the frequency short term stability2 × 10 11/x r and the long term stability 3.5 x 10-13 forone day sample time have been obtained.

  1. Viscosity of aqueous-glyceric solutions of potassium, rubidium and cesium chlorides

    International Nuclear Information System (INIS)

    Results of viscometric investigation of the solutions of rubidium and cesium chlorides (also potassium chloride for comparison) in mixtures water-glycerine at 15, 25, 35 and 45 deg C are presented. Glycerine content constituted 0.01; 0.03; 0.05; 0.07; 0.11 molar fractions. It is shown that the range of viscosity values lower as compared to the ones for pure solvent are the wider the lower the temperature and glycerine content are (in the range of 0.01-0.11 molar fractions). The composition-viscosity, temperature-viscosity diagrams are presented

  2. Study of ferroelectric properties of spray pyrolysis deposited cesium nitrate films

    Energy Technology Data Exchange (ETDEWEB)

    Nautiyal, Arvind, E-mail: nautyphysics@gmail.co [Ferroelectric Materials and Devices Research Laboratory, Department of Physics, Indian Institute of Technology Roorkee, Roorkee 247667 (Uttrakhand) (India); Sekhar, K.C. [Ferroelectric Materials and Devices Research Laboratory, Department of Physics, Indian Institute of Technology Roorkee, Roorkee 247667 (Uttrakhand) (India); Pathak, N.P. [Radio Frequency Integrated Circuits Research Laboratory, Department of Electronics and Computer Engineering, Indian Institute of Technology Roorkee, Roorkee 247667 (Uttrakhand) (India); Nath, R., E-mail: rnathfph@iitr.ernet.i [Ferroelectric Materials and Devices Research Laboratory, Department of Physics, Indian Institute of Technology Roorkee, Roorkee 247667 (Uttrakhand) (India)

    2010-10-01

    Cesium nitrate (CsNO{sub 3}) films were prepared by ultrasonic spray pyrolysis technique at different substrate temperatures (T{sub s}) and their ferroelectric and switching properties were examined. The morphology of the deposited films was studied using FESEM. The ferroelectric properties were optimized based on remanent polarization as a function of substrate temperature. The switching response was studied using pulse width technique. The switching parameters such as effective dimensionality, switching time, and nucleation rate were extracted using finite grain model (FGM). The width of reading pulse shows significant effect on switching transients.

  3. Electron electric dipole moment experiment using electric-field quantized slow cesium atoms

    OpenAIRE

    Amini, Jason M.; Munger Jr., Charles T.; Gould, Harvey

    2007-01-01

    A proof-of-principle electron electric dipole moment (e-EDM) experiment using slow cesium atoms, nulled magnetic fields, and electric field quantization has been performed. With the ambient magnetic fields seen by the atoms reduced to less than 200 pT, an electric field of 6 MV/m lifts the degeneracy between states of unequal lbar mF rbar and, along with the low (approximately 3 m/s) velocity, suppresses the systematic effect from the motional magnetic field. The low velocity and small r...

  4. Observation of X-ray-induced phase transition phenomenon of cesium manganese hexacyanoferrate

    Energy Technology Data Exchange (ETDEWEB)

    Ishiji, K [Kyushu Synchrotron Light Research Center, 8-7 Yayoigaoka, Tosu, Saga 841-0005 (Japan); Deguchi, M; Nakajima, N [Graduate School of Science, Hiroshima University, 1-3-1 Kagamiyama, Higashi-Hiroshima, Hiroshima 739-8526 (Japan); Matsuda, T; Tokoro, H; Ohkoshi, S [Department of Chemistry, School of Science, University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-0033 (Japan); Iwazumi, T, E-mail: ishiji@saga-ls.j [Department of Mathematical Sciences, Graduate School of Engineering, Osaka Prefecture University, 1-1 Gakuen-cho, Sakai, Osaka 599-8531 (Japan)

    2009-02-01

    Cesium manganese hexacyanoferrate is an interesting material which exhibits the phase transition with the magnetic susceptibility variation under the effect of external stimuli; such as temperature and visible light irradiation. This phase transition attributes the charge transfer between ions in the Fe-CN-Mn bond. Recently, we observed the phase transition by X-ray irradiation below 80 K. The X-ray absorption spectrum of the low-temperature (LT) phase approached toward that of the high-temperature (HT) phase. The spectrum variation by X-ray irradiation attributes the charge transfer from Fe{sup II} to Mn{sup III}.

  5. Open-path atmospheric transmission for a diode-pumped cesium laser.

    Science.gov (United States)

    Rice, Christopher A; Lott, Gordon E; Perram, Glen P

    2012-12-01

    A tunable diode laser absorption spectroscopy device was developed to study atmospheric propagation for emerging high-energy laser weapons. The cesium diode-pumped alkali laser operates near 895 nm in the vicinity of several water-vapor absorption lines. Temperature, pressure, and water vapor concentration were determined for 150 m and 1 km open paths with statistical errors of ∼0.2%. Comparison with meteorological instruments yields agreement for the 1 km path to within 0.6% for temperature, 3.7% for pressure, and 2.4% for concentration. PMID:23207380

  6. The transfer of fallout cesium-137 from browse to moose. Part 1

    International Nuclear Information System (INIS)

    We are investigating the transfer of fallout cesium-137 from soil to browse to moose (Alces alces) to wolf (Canis lupis) to promote our understanding of the movement of radionuclides through natural food chains. The first part of this study is concerned with moose food habits. Early winter food habits of moose from Hecla Island and Manitoba Game Hunting Area 26 in south central and south eastern Manitoba were studied. In 86 rumen samples, 25 food types were identified. Three methods of food habit determination were used: (1) percentage occurrence of food types, (2) subjective abundance scores and (3) percentage dry weight. All three methods yielded very similar results

  7. Research on the treatment of liquid waste containing cesium by an adsorption-microfiltration process with potassium zinc hexacyanoferrate

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Changping, E-mail: melindazhang@yahoo.com.cn [School of Environmental Science and Engineering, Tianjin University, Tianjin, 300072 (China); Gu Ping, E-mail: guping@tju.edu.cn [School of Environmental Science and Engineering, Tianjin University, Tianjin, 300072 (China); Zhao Jun; Zhang Dong; Deng Yue [Institute of Nuclear Physics and Chemistry, Chinese Academy of Engineering Physics, Mianyang 621900 (China)

    2009-08-15

    The removal of cesium from an aqueous solution by an adsorption-microfiltration (AMF) process was investigated in jar tests and lab-scale tests. The adsorbent was K{sub 2}Zn{sub 3}[Fe(CN){sub 6}]{sub 2}. The obtained cesium data in the jar test fit a Freundlich-type isotherm well. In the lab-scale test, the mean cesium concentration of the raw water and the effluent were 106.87 {mu}g/L and 0.59 {mu}g/L, respectively, the mean removal of cesium was 99.44%, and the mean decontamination factors (DF) and concentration factors (CF) were 208 and 539, respectively. The removal of cesium in the lab-scale test was better than that in the jar test because the old adsorbents remaining in the reactor still had adsorption capacity with the premise of no significant desorption being observed, and the continuous renewal of the adsorbent surface improved the adsorption capacity of the adsorbent. Some of the suspended solids were deposited on the bottom of the reactor, which would affect the mixing of adsorbents with the raw water and the renewing of the adsorbent surface. Membrane fouling was the main physical fouling mechanism, and the cake layer was the main filtration resistance. Specific flux (SF) decreased step by step during the whole period of operation due to membrane fouling and concentration polarization. The quality of the effluent was good and the turbidity remained lower than 0.1 NTU, and the toxic anion, CN{sup -}, could not be detected because of its low concentration, this indicated that the effluent was safe. The AMF process was feasible for practical application in the treatment of liquid waste containing cesium.

  8. Hepatoma-Targeted Radionuclide Immune Albumin Nanospheres: (131)I-antiAFPMcAb-GCV-BSA-NPs.

    Science.gov (United States)

    Lin, Mei; Huang, Junxing; Zhang, Dongsheng; Jiang, Xingmao; Zhang, Jia; Yu, Hong; Xiao, Yanhong; Shi, Yujuan; Guo, Ting

    2016-01-01

    An effective strategy has been developed for synthesis of radionuclide immune albumin nanospheres ((131)I-antiAFPMcAb-GCV-BSA-NPs). In vitro as well as in vivo targeting of (131)I-antiAFPMcAb-GCV-BSA-NPs to AFP-positive hepatoma was examined. In cultured HepG2 cells, the uptake and retention rates of (131)I-antiAFPMcAb-GCV-BSA-NPs were remarkably higher than those of (131)I alone. As well, the uptake rate and retention ratios of (131)I-antiAFPMcAb-GCV-BSA-NPs in AFP-positive HepG2 cells were also significantly higher than those in AFP-negative HEK293 cells. Compared to (131)I alone, (131)I-antiAFPMcAb-GCV-BSA-NPs were much more easily taken in and retained by hepatoma tissue, with a much higher T/NT. Due to good drug-loading, high encapsulation ratio, and highly selective affinity for AFP-positive tumors, the (131)I-antiAFPMcAb-GCV-BSA-NPs are promising for further effective radiation-gene therapy of hepatoma.

  9. 41 CFR 301-10.131 - What does United States mean?

    Science.gov (United States)

    2010-07-01

    ... 41 Public Contracts and Property Management 4 2010-07-01 2010-07-01 false What does United States mean? 301-10.131 Section 301-10.131 Public Contracts and Property Management Federal Travel Regulation System TEMPORARY DUTY (TDY) TRAVEL ALLOWANCES ALLOWABLE TRAVEL EXPENSES 10-TRANSPORTATION EXPENSES Common Carrier Transportation Use of...

  10. 17 CFR 1.31 - Books and records; keeping and inspection.

    Science.gov (United States)

    2010-04-01

    ... Electronic Recordkeeper's electronic storage media to any medium acceptable under 17 CFR 1.31. The... 17 Commodity and Securities Exchanges 1 2010-04-01 2010-04-01 false Books and records; keeping and... REGULATIONS UNDER THE COMMODITY EXCHANGE ACT Recordkeeping § 1.31 Books and records; keeping and...

  11. 46 CFR 131.875 - Lifejackets, immersion suits, and ring buoys.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Lifejackets, immersion suits, and ring buoys. 131.875... OPERATIONS Markings for Fire Equipment and Emergency Equipment § 131.875 Lifejackets, immersion suits, and ring buoys. (a) Each lifejacket, immersion suit, and ring life buoy must be marked in block...

  12. Manual on therapeutic uses of iodine-131. Incorporating: Applications guide, procedures guide, basics guide

    International Nuclear Information System (INIS)

    This booklet contains information about procedures to protect hospital staff and visitors and families of patients treated with iodine 131 from exposure to radiation from I-131. It also includes a basic guide to the principles of the production of ionizing radiation and to methods of radiation protection and dosimetry

  13. 29 CFR 794.131 - “Customer * * * engaged in bulk distribution”.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 3 2010-07-01 2010-07-01 false âCustomer * * * engaged in bulk distributionâ. 794.131... Sales Made to Other Bulk Distributors § 794.131 “Customer * * * engaged in bulk distribution”. A sale to a customer of an enterprise engaged in the wholesale or bulk distribution of petroleum products...

  14. 26 CFR 1.501(c)(13)-1 - Cemetery companies and crematoria.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 7 2010-04-01 2010-04-01 true Cemetery companies and crematoria. 1.501(c)(13)-1...) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Exempt Organizations § 1.501(c)(13)-1 Cemetery companies and crematoria. (a) Nonprofit mutual cemetery companies. A nonprofit cemetery company may be...

  15. 40 CFR 131.20 - State review and revision of water quality standards.

    Science.gov (United States)

    2010-07-01

    ... public participation regulation (40 CFR part 25). The proposed water quality standards revision and... quality standards. 131.20 Section 131.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS WATER QUALITY STANDARDS Procedures for Review and Revision of Water...

  16. 19p13.1 is a triple-negative-specific breast cancer susceptibility locus

    DEFF Research Database (Denmark)

    Stevens, Kristen N; Fredericksen, Zachary; Vachon, Celine M;

    2012-01-01

    The 19p13.1 breast cancer susceptibility locus is a modifier of breast cancer risk in BRCA1 mutation carriers and is also associated with the risk of ovarian cancer. Here, we investigated 19p13.1 variation and risk of breast cancer subtypes, defined by estrogen receptor (ER), progesterone recepto...

  17. Post-laryngectomy localization of I-131 at tracheostomy site on a total body scan

    Energy Technology Data Exchange (ETDEWEB)

    Kirk, G.A.; Schulz, E.E.

    1984-07-01

    A post-thyroidectomy, post-I-131-therapy patient had a laryngectomy and neck dissection for recurrent papillary thyroid carcinoma. A subsequent I-131 total body scan revealed persistent anterior neck activity, which disappeared upon removal of the tracheostomy tube and dressings.

  18. 46 CFR 131.910 - Notices to mariners and aids to navigation.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Notices to mariners and aids to navigation. 131.910... OPERATIONS Miscellaneous § 131.910 Notices to mariners and aids to navigation. Each master and mate shall... Imagery and Mapping Agency regarding aids to navigation in the area in which the vessel operates....

  19. The Effect of Carbonate, Oxalate and Peroxide on the Cesium Loading of Ionsiv IE-910 and IE-911

    Energy Technology Data Exchange (ETDEWEB)

    Fondeur, F.F.

    2000-12-19

    The Savannah River Site (SRS) continues to examine three processes for the removal of radiocesium from high-level waste. One option involves the use of crystalline silicotitanate (CST) as a non-elutable ion exchange medium. The process uses CST in its engineered form - IONSIV IE-911 made by UOP, LLC. - in a column to contact the liquid waste. Cesium exchanges with sodium ions residing inside the CST particles. The design disposes of the cesium-loaded CST by vitrification within the Defense Waste Processing Facility.

  20. Volume reduction of lake sediment and decrease of its cesium content in decontamination process by wet oxidation method

    International Nuclear Information System (INIS)

    Wet oxidation method was applied aiming to decrease cesium contents in lake sediment. In this research, “reactive oxygen water”, that is prepared from hypochlorous acid by contact with metal ceramics, was reacted with three kinds of samples, that is, lake sediment, mixture of lake sediment and fallen leaves, and incineration ash of fallen leaves. Experimental results revealed that sample volume was reduced by means of wet oxidation of organic components in samples and that a large amount of cesium contents were transferred from sample to water phase. (author)

  1. Virulence potential and genomic mapping of the worldwide clone Escherichia coli ST131.

    Directory of Open Access Journals (Sweden)

    Jean-Philippe Lavigne

    Full Text Available Recently, the worldwide propagation of clonal CTX-M-15-producing Escherichia coli isolates, namely ST131 and O25b:H4, has been reported. Like the majority of extra-intestinal pathogenic E. coli isolates, the pandemic clone ST131 belongs to phylogenetic group B2, and has recently been shown to be highly virulent in a mouse model, even though it lacks several genes encoding key virulence factors (Pap, Cnf1 and HlyA. Using two animal models, Caenorhabditis elegans and zebrafish embryos, we assessed the virulence of three E. coli ST131 strains (2 CTX-M-15- producing urine and 1 non-ESBL-producing faecal isolate, comparing them with five non-ST131 B2 and a group A uropathogenic E. coli (UPEC. In C. elegans, the three ST131 strains showed intermediate virulence between the non virulent group A isolate and the virulent non-ST131 B2 strains. In zebrafish, the CTX-M-15-producing ST131 UPEC isolates were also less virulent than the non-ST131 B2 strains, suggesting that the production of CTX-M-15 is not correlated with enhanced virulence. Amongst the non-ST131 B2 group isolates, variation in pathogenic potential in zebrafish embryos was observed ranging from intermediate to highly virulent. Interestingly, the ST131 strains were equally persistent in surviving embryos as the non-ST131-group B2 strains, suggesting similar mechanisms may account for development of persistent infection. Optical maps of the genome of the ST131 strains were compared with those of 24 reference E. coli strains. Although small differences were seen within the ST131 strains, the tree built on the optical maps showed that these strains belonged to a specific cluster (86% similarity with only 45% similarity with the other group B2 strains and 25% with strains of group A and D. Thus, the ST131 clone has a genetic composition that differs from other group B2 strains, and appears to be less virulent than previously suspected.

  2. Labelling of human serum albumin with iodine-131 for diagnosis in nuclear medicine

    International Nuclear Information System (INIS)

    Labelling of 131I-human serum albumin with I-131 from a solution of 131I-sodium iodide using chloramine T as an oxidant agent is studied. Parameters which can influence on the labelling yield like mass of human serum albumin, and chloramine T, pH of the reaction, reaction time and activity of 131I are also studied. The purification of the labeled product by means of IRA-410 Amberlite ion-exchange resin in chloride form and the sterilization of the 131I-human serum albumin by its passage through a 0,22μ millipore filter are carried out. The radiochemistry control of the final product by paper chromatography and the microbiological control by cultivation of microorganisms in fluid medium: nutrient broth, sodium thioglycollate broth and Sabouraud, are performed. The stability of the radiopharmaceutical until ten days after its preparation is analysed by means of radiochemical control. (Author)

  3. Analysis of factors for early hypothyroidism after 131I treatment of hyperthyroidism

    International Nuclear Information System (INIS)

    To explore the factors for the early hypothyroidism following 131I treatment of hyperthyroidism, clinic data of 120 hyperthyroidism patients including 8 independent and 1 dependent variables after one year 131I treatment were analyzed by logistic regression analysis method. The results showed that the average 131I dosage given to one gram thyroid tissue was correlated positively with early hypothyroidism occurrence, and the weight of thyroid was negatively correlated to early hypothyroidism occurrence. The positive and negative prediction accuracy of the early hypothyroidism were 53.3% and 96.1% respectively, and the total prediction accuracy was 46.7%. The results suggest that the 131I dosage and the weight of thyroid are key factors for early hypothyroidism; the appropriate adjustment of 131I dosage based on the thyroid mass could prevent the early hypothyroidism occurrence in certain degree. (authors)

  4. Iodine-131 uptake in a patient with thyroid cancer and rheumatoid arthritis during acupuncture treatment

    Energy Technology Data Exchange (ETDEWEB)

    Otsuka, N.; Fukunaga, M.; Morita, K.; Ono, S.; Nagai, K.; Katagiri, M.; Harada, T.; Morita, R. (Kawasaki Medical School, Okayama (Japan))

    1990-01-01

    A patient with thyroid carcinoma had abnormal accumulation of I-131 in the areas of both feet and hands on whole body scan. The sites of abnormal accumulation of I-131 were similar to those on bone scintigraphy. The radiographic examination of the lesions showed characteristic findings of rheumatoid arthritis, and the presence of small gold needles for acupuncture treatment was demonstrated. There were no findings of bone metastases. Although the mechanism of accumulation of I-131 in this patient is unknown, interpreters of I-131 whole body scintigraphs should keep this case in mind when acupuncture treatment has been done. The authors can only speculate on a common blood flow mechanism for enhanced HMDP and I-131 uptake in this arthritic patient who had been treated by acupuncture.

  5. Synthesis and 131I labelling of epidepride as a dopamine D2 receptor imaging agent

    International Nuclear Information System (INIS)

    S-(-)-N-[(1-ethyl-2-pyrrolidinyl)methyl]-5-iodo-2, 3-dimethoxybenzamide (Epidepride) and its iodine labeling precursor S-(-)-N-[(1-Ethyl-2-pyrrolidinyl)methyl]-5-tributyltin-2, 3-dimethoxybenzamide are synthesized from 3-methoxy salicylic acid. The labeling precursor is labeled with 131I by hydrogen peroxide method, and 131I-epidepride is gained, its radiolabelling yield (RLY) and the radiochemical purity (RCP) are all over 95%. The RCP of 131I-epidepride is over 90% under 4 degree C after 15 days. 131I-epidepride has high affinity to dopamine D2 receptor. The striatal uptake can be blocked completely by spiperone. The striatum and cerebellum uptake ratio can reach 237 at 320 min in rats. The results show that 131I-epidepride may be used as a dopamine D2 receptor imaging agent for SPECT

  6. Metabolic therapy of thyroid by {sup 131}I and radiation protection; Therapie metabolique thyroidienne par {sup 131}I et radioprotection

    Energy Technology Data Exchange (ETDEWEB)

    Mathieu, I.; Caussin, J.; Smeesters, P.; Wambersie, A.; Beckers, C. [Centre de Medecine Nucleaire, Universite Catholique de Louvain, B-1200 Brussels (Belgium)

    1997-12-31

    The recommendations of International Commission on Radiological Protection (ICRP 60) to be applied in the European Union from the year 2000 imply a limit of the annual dose of 1 mSv for public as well as the compliance with the dose constraints. In order to verify the possibility of observing these new standards without losing the very favourable cost-profit of the {sup 131}I therapy in thyroiditis, 73 members of patient families treated by radioiodine were surveyed by direct dosimetry. A number of 22 patients afflicted with thyroid cancer received doses of 3700 to 7400 MBq and 18 hyperthyroid patients received 200 to 600 MBq. Dosemeters mounted around the neck were carried for 2-3 weeks by 35 spouses and 38 children 4 months to 25 years old. The residual thyroid radioactivity and the T{sub 1/2} of {sup 131}I were measured by gamma chambers in every patients. In the group of patients with thyroid cancers the effective T{sub 1/2} is 2.2 days. The doses measured in families are lower than 1 mSv in any spouses and lower than 0.3 mSv in all the children except one. In hyperthyroid patients the effective T{sub 1/2} is 6.2 days. The average dose received is 1.04 mSv (0.05-5.2) for spouses and 0.13 mSv (0.04-3.1) for children. These direct dosimetry data are reliable and allow to propose reasonable and efficient restrictions which will not compromise neither the efficiency of treatment or the environment safety

  7. Therapeutic efficacy of intralesional 131I-labelled hyaluronectin in grafted human glioblastoma

    Energy Technology Data Exchange (ETDEWEB)

    Girard, N.; Courel, M.N.; Vera, P.; Delpech, B. [Centre Henri-Becquerel, Rouen (France). Laboratoire d' Oncologie Moleculaire

    2000-07-01

    The grafted human glioblastoma cell CB109 was used as a model for intralesional therapy with 131I-labelled hyaluronectin glycoprotein (131I-HN). 131I-HN bound specifically to in situ hyaluronic acid (HA), a main component of the extracellular matrix which is involved in tumour invasion. Labelling experimental conditions were determined and, finally, 25 {mu}Ci/{mu}gHN, 1 {mu}g chloramine-T/{mu}gHN and a 60-s stirring period provided a 131I-HN preparation with an optimal affinity for HA (64% compared to unlabelled HN). Following intratumoral injection, 131I-HN was retained with a limited diffusion outside the tumour. On day 4 the radioactivity concentrated in the tumour was still 25 times greater than that in the liver, spleen and kidneys combined. For therapeutic assays, 65 {mu}Ci 131I-HN was injected into the tumour, resulting in a delivery of 6.8 Gy over a 7-day period. Controls received unlabelled HN, heat-inactivated HN, a mixture of inactivated HN plus free 131I or no treatment (six animals per group). Tumour volumes were evaluated every second day from treatment day and the rate of tumour growth was expressed as a ratio of tumour size at time intervals to the tumour size at the time of injection. Growth curves were compared: heat-inactivated with or without free 131I had no anti-tumour effect. Unlabelled HN-injected tumours had a slightly slower growth rate than untreated tumours (p < 0.02) and growth rate of 131I-HN-injected tumours was much lower (p < 0.00002). A pronounced inhibitory effect with intralesional 131I-labelled HN injection resulted from a combination of a) blockage of HA, a proliferation facilitating factor, and b) local irradiation of tumoral tissue, while uptake in normal tissues was minimized.

  8. 131I治疗单叶Graves’病的临床分析%The clinical analysis of 131I treatment in the single leaf Graves, disease

    Institute of Scientific and Technical Information of China (English)

    张怡; 袁卫红

    2014-01-01

    Objective The single leaf Graves, and the double leaves Graves, patients were observed in 60 cases after 131I treatment, and observe the clinical and fol ow-up data of patients, analysis and comparison of 131I in the treatment of the single leaf Graves, and the double leaves Graves, in patients with clinical efficacy. Method Two groups of patients were adopted 131I treatment, fol ow-up observation were performed after treatment, compared with the 131I treated thyroid narrowing effect degree and treatment situation, to analyze the 131I treatment effect in the single leaf Graves , and the double leaves Graves,. Result The single leaf Graves, 131I treatment group: before and after the treatment of thyroid volume reduction of the statistical y significant difference. 43 cases were cured (71.7%), improved in 13 cases (21.7%), invalid 4 cases (6.6%), effective rate was 93.3%, the cure rate was 71.7%. The double leaves Graves, 131I treatment group: 46 cases were cured (76.7%), improved in 11 cases (18.3%), invalid 3 cases (5%), effective rate was 95%, the cure rate was 76.7% .Conclusion For the single leaf Graves, disease take 131I treatment, the curative effect of treatment with 131I in the double leaves Graves, disease withnot significant difference. The single leaf Graves, patients in thyroid tissue, thyroid scintigraphy in the uptake function hyperfunction of the leaf were reassessed, adopted the 131I treatment, as long as the treatment dose properly, adhere to individualized treatment plan, strengthening fol ow-up after treatment, can achieve effective results. 131I treatment of Graves, disease, has the advantages of simple, effective, safe,and economy.%目的:分别观察60例经过131I治疗的单叶Graves,病患者和双叶Graves,病患者的临床和随访资料,分析和比较131I治疗单叶Graves,病和双叶Graves,病患者的临床疗效。方法两组患者分别采取131I治疗,治疗后均进行随访观察,通过对比131I治疗后甲状

  9. Functionalized magnetic nanoparticles for the decontamination of water polluted with cesium

    Directory of Open Access Journals (Sweden)

    Ahmed S. Helal

    2016-05-01

    Full Text Available Magnetic nanoparticles are attracting considerable interest because of their potential applications in practically all fields of science and technology, including the removal of heavy metals from contaminated waters. It is, therefore, of great importance to adapt the surfaces of these nanoparticles according to the application. In this work advanced nanoparticles (NPs with well-tailored surface functionalities were synthesized using the polyol method. The efficiency of a chelating agent, succinyl-β-cyclodextrin (SBCD, was first investigated spectrophotometrically and by Isothermal Titration Calorimetry (ITC. SBCD was then grafted onto nanoparticles previously functionalized with 3-aminopropyl triethoxsilane (NP-APTES. The resulting NP-SBCD system was then incubated with a solution of cesium. After magnetic separation, the solid residue was removed from the supernatant and characterized by X-Ray Photoelectron spectrometry (XPS, X-Ray Fluorescence spectrometry (XRF and Superconducting QUantum Interference Device (SQUID magnetometry. These characterizations show the presence of cesium in the solid residue, which indicates Cs uptake by the NP-SBCD system. This nanohybrid system constitutes a promising model for heavy metal decontamination.

  10. Production of negative D- ions by double charge exchange using cesium

    International Nuclear Information System (INIS)

    The first experimental results on the source of D- negative ions developed at SIG confirm a certain number of essential points: (1) the use of a positive ion source obtained by a resonance electronic cyclotron permits the production of D+ ion beams with a very small gas output, therefore it has a very good gas efficiency; (2) the supersonic cesium target obtained after the release of a high temperature cesium vapor functions perfectly with the desired characteristics; (3) the conversion efficiency measured in D- ions is close to those which were deduced from experimental cross sections; and (4) the mean density of D- ion currents is on the order of 10 mA/cm2 at 1 keV. They could be 15 at 25 mA/cm2 at 300 eV. This presupposes that we modify the extraction optic for the D+ ions to extract 60 at 70 mA/cm2 of D+ at 300 eV with a maximum electric field of 30 DV/cm and a greater perveance of the optic

  11. Critical literature study on the cesium transfer feed/meat of domestic animals

    International Nuclear Information System (INIS)

    A literature study concerning the transfer of cesium from feed to meat of domestic and wild animals has been carried out regarding approx. 3200 publications of the period 1950-1979. General criteria for the influence of experimental conditions on the transfer factor have been found. The transfer factor of radioisotopes of cesium is always smaller by one order of magnitude after single ingestion than after continuous administration until an equilibrium of incorporation to excretion is attained. The transfer factor of growing animals is greater than that of adult animals where transfer factor is not a function of age. The sex of the animals has no influence on the transfer factor. This value decreases with increasing weight of the animals. From these findings average transfer factors have been derived as follows: cattle 0.03 +- 0.02; calf 0.43 +- 0.06; goat 0.20; sheep 0.11 +- 0.02; pig 0.26 +- 0.01; hen 4.5; reindeer/caribou 0.31 +- 0.07; deer 0.18 +- 0.03. These values have been extracted from the original literature and relate mainly to animals undergoing metabolic experiments at equilibrium. Only the transfer factors of deer and caribou have been evaluated from data of the radiocesium concentration in feed and in meat. (orig.)

  12. Strontium-90 and cesium-137 in soil (from May 1985 to Jul. 1985)

    International Nuclear Information System (INIS)

    This report is aimed at listing measurements of strontium-90 and cesium-137 in soil made at eight places across Japan during the period from May to July in 1985. Collection and pretreatment methods are described for samples of rain and dry fallout, airborne dust, service water and freshwater, soil, sea water, sea sediments, total diet, rice, milk, vegetables, tea, as well as fish, shellfish and seaweeds. The methods for the preparation of these samples for analysis are also outlined. Sample solutions were neutralized with sodium hydroxide, and the precipitate of strontium and calcium carbonates was separated after sodium carbonate was added. The supernatant solution was retained for cesium-137 determination. After being precipitated as oxalates, strontium and calcium were separated by successive fuming nitric acid separations. For the determination of stable strontium, calcium and potassium, soil and sediment were treated with sodium hydroxide and hydrochloric acid for extraction while other samples were ashed and digested. Calcium, separated as oxalate, was determined by titration while stable strontium and potassium were determined by atomic absorption and flame emission spectroscopy, respectively. Couting for activity was carried out using low background beta counters normally for 60 min. (Nogami, K.)

  13. Research on ultracold cesium molecule long-range states by high-resolution photoassociative spectroscopy

    Institute of Scientific and Technical Information of China (English)

    WANG LiRong; MA Jie; JI WeiBang; WANG GuiPing; XIAO LianTuan; JIA SuoTang

    2008-01-01

    In this paper, an ultra-high resolution photoassociation spectroscopy study on photoassociation of cesium atoms is reported. The cold cesium gas in the mag-neto-optical trap is illuminated by a photoassociation laser with red-tuning as large as 40 cm-1 below the 6S1/2 + 6P3/2 dissociation limit, and the photoassoclation to the excited state ultracold molecule is detected. High signal-to-noise ratio is obtained by using the lock-in detection of the fluorescence from the modulated cold Cs at-oms. The O-g, and O+u, long-range states which correspond to 6S1/2 + 6P3/2 diSsocia-tion limit are present in the photoassociation spectrum. The effective coefficients of leading long-range interactions and the corresponding vibrational quantum num-ber are obtained using LeRoy-Bernstein Law. It is found that photoassociation process creates rotating molecules and the high J value is a hint that higher partial waves participate in the PA process in the presence of trapping laser.

  14. The behavior of cesium iodide radioaerosols during CsI sublimation from metal surface

    International Nuclear Information System (INIS)

    One of the biologically most dangerous volatile fission products getting into the environment during hypothetical severe accidents at NPPs are CsI radioaerosols. This is the reason why great attention is now being devoted to a study of the behavior of CsI radioaerosols in the steam-gas phase. We studied the behavior of CsI aerosols using a setup made of a steam generator, a reaction chamber with a Pt heater, a condenser, bubblers with a Na2S2O3 solution, and a Petryanov filter. The method of radionuclide diagnostic was used for study of the CsI behavior during sublimation from the metal surface. The theoretical mass ratio between cesium and iodine in the CsI molecule is equal to 1.04. So, an upward deviation from this theoretical value will show an increase in the amount of cesium, and, respectively, a downward deviation will indicate an increase in the amount of iodine. Thus, change in the Cs/I ratio was a parameter with the help of which we considered estimating the extent of the oxidation hydrolysis of CsI aerosols. (orig.)

  15. Uncertainty of cesium-beam time standards due to beam asymmetry

    Science.gov (United States)

    Becker, G.

    1980-12-01

    As a consequence of the spatial phase distribution in the resonators of cesium-beam time and frequency standards, the generated frequency depends on the specific path of the atomic beam. A change of the position of the atomic beam source may result in a beam displacement normal to the beam direction. For a deflection system consisting of a combination of quadrupole and hexapole magnets for two-dimensional beam deflection, the displacement of the center of mass of the beam resulting from a misalignment of the beam source is computed. To this end, the distribution of the beam intensity on the collector is first determined. It is shown that for the cesium-beam time and frequency standard CS1 of the Physikalisch-Technische Bundesanstalt (PTB), the uncertainty of the position of the center of mass of the beam entails a contribution to the uncertainty of the standard of less than 1 x 10 to the -15th. The amount of the displacement of the center of mass of the beam can be determined from the decrease of the beam flux on the collector caused by an adjustment of the beam source.

  16. Strontium-90 and cesium-137 in service water from December, 1981, to July, 1982

    International Nuclear Information System (INIS)

    Service water, 100 liters each, was collected at an intake of a water-treatment plant and at a tap after water was left running for five minutes. Water, to which the carriers of strontium and cesium were added immediately after sampling, was vigorously stirred and filtered. The sample was then passed through a cation exchange column. After radiochemical separation, the precipitates were counted for the activity using a low-background beta counter, normally for 60 min. The measuring techniques are first described; i.e. the collection and pretreatment of samples, the preparation of samples for analysis, the separation of strontium-90 and cesium-137, and the counting. The measured results are given in a table for the following locations: source water - Tokyo, Osaka, Hokkaido, Kyoto, Kanagawa, Aichi, Fukuoka; tap water - Hokkaido, Akita, Fukushima, Tokyo, Fukui, Shizuoka, Shimane, Okayama, Fukuoka, Saga, Nagasaki, Kyoto, Wakayama, Okinawa, Hiroshima, Aomori, Yamagata, Ibaraki, Kanagawa, Niigata, Ishikawa, Nagano, Aichi, Osaka, Hyogo, Tottori, Yamaguchi, Ehime, Kochi, Kagoshima. (Mori, K.)

  17. Functionalized magnetic nanoparticles for the decontamination of water polluted with cesium

    Science.gov (United States)

    Helal, Ahmed S.; Decorse, Philippe; Perruchot, Christian; Novak, Sophie; Lion, Claude; Ammar, Souad; El Hage Chahine, Jean-Michel; Hémadi, Miryana

    2016-05-01

    Magnetic nanoparticles are attracting considerable interest because of their potential applications in practically all fields of science and technology, including the removal of heavy metals from contaminated waters. It is, therefore, of great importance to adapt the surfaces of these nanoparticles according to the application. In this work advanced nanoparticles (NPs) with well-tailored surface functionalities were synthesized using the polyol method. The efficiency of a chelating agent, succinyl-β-cyclodextrin (SBCD), was first investigated spectrophotometrically and by Isothermal Titration Calorimetry (ITC). SBCD was then grafted onto nanoparticles previously functionalized with 3-aminopropyl triethoxsilane (NP-APTES). The resulting NP-SBCD system was then incubated with a solution of cesium. After magnetic separation, the solid residue was removed from the supernatant and characterized by X-Ray Photoelectron spectrometry (XPS), X-Ray Fluorescence spectrometry (XRF) and Superconducting QUantum Interference Device (SQUID) magnetometry. These characterizations show the presence of cesium in the solid residue, which indicates Cs uptake by the NP-SBCD system. This nanohybrid system constitutes a promising model for heavy metal decontamination.

  18. Nanophotonic hybridization of narrow atomic cesium resonances and photonic stop gaps of opaline nanostructures

    CERN Document Server

    Harding, Philip J; Mosk, Allard P; Vos, Willem L

    2014-01-01

    We study a hybrid system consisting of a narrowband atomic optical resonance and the long-range periodic order of an opaline photonic nanostructure. To this end, we have infiltrated atomic cesium vapor in a thin silica opal photonic crystal. With increasing temperature, the frequencies of the opal's reflectivity peaks shift down by >20% due to chemical reduction of the silica. Simultaneously, the photonic bands and gaps shift relative to the fixed near-infrared cesium D1 transitions. As a result the narrow atomic resonances with high finesse (f/df=8E5) dramatically change shape from a usual dispersive shape at the blue edge of a stop gap, to an inverted dispersion lineshape at the red edge of a stop gap. The lineshape, amplitude, and off-resonance reflectivity are well modeled with a transfer-matrix model that includes the dispersion and absorption of Cs hyperfine transitions and the chemically-reduced opal. An ensemble of atoms in a photonic crystal is an intriguing hybrid system that features narrow defect-...

  19. Transfer data for radio-cesium in the food chain feed/meat

    International Nuclear Information System (INIS)

    It is necessary to have some knowledge of the behaviour of radioactive material in the food chain to be able to assess the radiation exposure of humans via the ingestion path way. The transfer factor has to be defined precisely because there is a linear dependence of the radiation dose on the transfer factor in the mathematical models for calculating the annual radiation doses. Knowledge of the animal-specific cesium retention, of the biological half-life as well as of the distribution system is required for an accurate calculation of the transfer-data of the particularly important radionuclide cesium 137. After having studied the original literature thoroughly the following transfer factors have been found as an average: cattle 0.03 +- 0.02, calf 0.43 +- 0.06, goat 0.20, sheep 0.11 +- 0.02, swine 0.26 +- 0.01, chicken 3.23 +- 1.41, reindeer 0.31 +- 0.07. (MG)

  20. Nanophotonic hybridization of narrow atomic cesium resonances and photonic stop gaps of opaline nanostructures

    Science.gov (United States)

    Harding, Philip J.; Pinkse, Pepijn W. H.; Mosk, Allard P.; Vos, Willem L.

    2015-01-01

    We study a hybrid system consisting of a narrow-band atomic optical resonance and the long-range periodic order of an opaline photonic nanostructure. To this end, we have infiltrated atomic cesium vapor in a thin silica opal photonic crystal. With increasing temperature, the frequencies of the opal's reflectivity peaks shift down by >20 % due to chemical reduction of the silica. Simultaneously, the photonic bands and gaps shift relative to the fixed near-infrared cesium D1 transitions. As a result the narrow atomic resonances with high finesse (ω /Δ ω =8 ×105 ) dramatically change shape from a usual dispersive shape at the blue edge of a stop gap, to an inverted dispersion line shape at the red edge of a stop gap. The line shape, amplitude, and off-resonance reflectivity are well modeled with a transfer-matrix model that includes the dispersion and absorption of Cs hyperfine transitions and the chemically reduced opal. An ensemble of atoms in a photonic crystal is an intriguing hybrid system that features narrow defectlike resonances with a strong dispersion, with potential applications in slow light, sensing, and optical memory.