WorldWideScience

Sample records for cerium 126

  1. Reaction chemistry of cerium

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-01-01

    It is truly ironic that a synthetic organic chemist likely has far greater knowledge of the reaction chemistry of cerium(IV) than an inorganic colleague. Cerium(IV) reagents have long since been employed as oxidants in effecting a wide variety of organic transformations. Conversely, prior to the late 1980s, the number of well characterized cerium(IV) complexes did not extend past a handful of known species. Though in many other areas, interest in the molecular chemistry of the 4f-elements has undergone an explosive growth over the last twenty years, the chemistry of cerium(IV) has for the most part been overlooked. This report describes reactions of cerium complexes and structure.

  2. Probing the cerium/cerium hydride interface using nanoindentation

    Energy Technology Data Exchange (ETDEWEB)

    Brierley, Martin, E-mail: martin.brierley@awe.co.uk [Atomic Weapons Establishment, Aldermaston, Berkshire RG7 4PR (United Kingdom); University of Manchester, Manchester M13 9PL (United Kingdom); Knowles, John, E-mail: john.knowles@awe.co.uk [Atomic Weapons Establishment, Aldermaston, Berkshire RG7 4PR (United Kingdom)

    2015-10-05

    Highlights: • A disparity exists between the minimum energy and actual shape of a cerium hydride. • Cerium hydride is found to be harder than cerium metal by a ratio of 1.7:1. • A zone of material under compressive stress was identified surrounding the hydride. • No distribution of hardness was apparent within the hydride. - Abstract: A cerium hydride site was sectioned and the mechanical properties of the exposed phases (cerium metal, cerium hydride, oxidised cerium hydride) were measured using nanoindentation. An interfacial region under compressive stress was observed in the cerium metal surrounding a surface hydride that formed as a consequence of strain energy generated by the volume expansion associated with precipitation of the hydride phase.

  3. Probing the cerium/cerium hydride interface using nanoindentation

    International Nuclear Information System (INIS)

    Highlights: • A disparity exists between the minimum energy and actual shape of a cerium hydride. • Cerium hydride is found to be harder than cerium metal by a ratio of 1.7:1. • A zone of material under compressive stress was identified surrounding the hydride. • No distribution of hardness was apparent within the hydride. - Abstract: A cerium hydride site was sectioned and the mechanical properties of the exposed phases (cerium metal, cerium hydride, oxidised cerium hydride) were measured using nanoindentation. An interfacial region under compressive stress was observed in the cerium metal surrounding a surface hydride that formed as a consequence of strain energy generated by the volume expansion associated with precipitation of the hydride phase

  4. Thermodynamic properties of cerium oxide

    International Nuclear Information System (INIS)

    Thermodynamic properties of cerium oxides in the CeO2-CeO1.5 composition range are studied. For this purpose method of electromotive force with solid electrolyte is used, equilibrium constants of reduction of cerium oxides by hydrogen are measured. Necessity of using atmosphere of argon or purified nitrogen to work with pyrophoric cerium oxides is stressed. The obtained results and the earlier known literary data on CeO2 and Ce2O3 thermodynamic properties are tabulated. 14 refs.; 5 tabs

  5. Mechanochemical synthesis of cerium orthophosphate

    Institute of Scientific and Technical Information of China (English)

    A.Matraszek; I.Szczygiei; L.Macalik; J.Hanuza

    2009-01-01

    A facile,simple and rapid preparation method of cerium orthophosphate was presented.The synthesis of low-crystalline CePO4 occurred upon mixing of cerium (Ⅲ) nitrate and sodium phosphate,and was an exchange-type reaction.The phase composition of the obtained powder was checked by the XRD and FTIR methods,indicating the presence of cerium phosphate.Further investigations on thermal behavior of the synthesized cerium salt had shown that the obtained onhophosphate crystallized at first in rhabdophane-type structure.It convetted to monazite (monoclinic symmetry) during heating at the temperatures of above 600 ℃.Oxidation of Ce3+ to Ce4+ was avoided during the syntheses,as confirmed by the XPS experiments.

  6. Preparation of cerium halide solvate complexes

    Science.gov (United States)

    Vasudevan, Kalyan V; Smith, Nickolaus A; Gordon, John C; McKigney, Edward A; Muenchaussen, Ross E

    2013-08-06

    Crystals of a solvated cerium(III) halide solvate complex resulted from a process of forming a paste of a cerium(III) halide in an ionic liquid, adding a solvent to the paste, removing any undissolved solid, and then cooling the liquid phase. Diffusing a solvent vapor into the liquid phase also resulted in crystals of a solvated cerium(III) halide complex.

  7. MAT 126 ASH Course Tutorial / Tutorialoutlet

    OpenAIRE

    stylia

    2015-01-01

    For more course tutorials visit www.tutorialoutlet.com   MAT 126 Week 1 DQ 1 (Ash) MAT 126 Week 1 Quiz (Ash) MAT 126 Week 1 Written Assignment (Arithmetic and geometric sequence) (Ash) MAT 126 Week 2 DQ 1 (Ash) MAT 126 Week 2 DQ 2 (Ash) MAT 126 Week 2 Assignment Is It Fat Free (Ash) MAT 126 Week 2 Quiz (Ash) MAT 126 Week 3 DQ 1 (Ash) MAT 126 Week 3 DQ 2 (Ash) MAT 126 Week 3 Assignment Quadratic Equations (Ash) MAT 126 Week 3 Quiz (Ash) MAT 126...

  8. PLUTONIUM-CERIUM-COBALT AND PLUTONIUM-CERIUM-NICKEL ALLOYS

    Science.gov (United States)

    Coffinberry, A.S.

    1959-08-25

    >New plutonium-base teroary alloys useful as liquid reactor fuels are described. The alloys consist of 10 to 20 atomic percent cobalt with the remainder plutonium and cerium in any desired proportion, with the plutonium not in excess of 88 atomic percent; or, of from 10 to 25 atomic percent nickel (or mixture of nickel and cobalt) with the remainder plutonium and cerium in any desired proportion, with the plutonium not in excess of 86 atomic percent. The stated advantages of these alloys over unalloyed plutonium for reactor fuel use are a lower melting point and a wide range of permissible plutonium dilution.

  9. Dissolution properties of cerium dibutylphosphate corrosion inhibitors

    NARCIS (Netherlands)

    Soestbergen, M. van; Erich, S.J.F.; Huinink, H.P.; Adan, O.C.G.

    2013-01-01

    The corrosion inhibitor cerium dibutylphosphate, Ce(dbp)3, prevents corrosion by cerium and dbp deposition at the alkaline cathode and acidic anode respectively. The pH dependent Ce(dbp)3 solubility seems to play an essential role in the inhibition degree. We found that Ce(dbp) 3 scarcely dissolves

  10. Inhibited oxidation of polymethylsiloxane, containing cerium

    International Nuclear Information System (INIS)

    The kinetics of oxidation of oligomeric polydimethylsiloxane in the presence of cerium-containing organosilicon antioxidant at 285-310 deg was investigated. High energy of activation for initiation process (around 272 kJ/mole) was established as a feature specific for chain oxidation of polydimethylsiloxane. It was found that cerium-containing antioxidant, as well as the iron-containing one, based on iron capronate, is of the ''depleting'' inhibitors, i.e. it looses its inhibiting ability during oxidation

  11. Pharmacological potential of cerium oxidenanoparticles

    Science.gov (United States)

    Celardo, Ivana; Pedersen, Jens Z.; Traversa, Enrico; Ghibelli, Lina

    2011-04-01

    Nanotechnology promises a revolution in pharmacology to improve or create ex novo therapies. Cerium oxidenanoparticles (nanoceria), well-known as catalysts, possess an astonishing pharmacological potential due to their antioxidant properties, deriving from a fraction of Ce3+ ions present in CeO2. These defects, compensated by oxygen vacancies, are enriched at the surface and therefore in nanosized particles. Reactions involving redox cycles between the Ce3+ and Ce4+oxidation states allow nanoceria to react catalytically with superoxide and hydrogen peroxide, mimicking the behavior of two key antioxidant enzymes, superoxide dismutase and catalase, potentially abating all noxious intracellularreactive oxygen species (ROS) via a self-regenerating mechanism. Hence nanoceria, apparently well tolerated by the organism, might fight chronic inflammation and the pathologies associated with oxidative stress, which include cancer and neurodegeneration. Here we review the biological effects of nanoceria as they emerge from in vitro and in vivo studies, considering biocompatibility and the peculiar antioxidant mechanisms.

  12. 46 CFR 126.240 - Posting.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Posting. 126.240 Section 126.240 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OFFSHORE SUPPLY VESSELS INSPECTION AND CERTIFICATION Certificate of Inspection § 126.240 Posting. The Certificate of Inspection must be framed under glass or...

  13. 22 CFR 126.13 - Required information.

    Science.gov (United States)

    2010-04-01

    ... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Required information. 126.13 Section 126.13... PROVISIONS § 126.13 Required information. (a) All applications for licenses (DSP-5, DSP-61, DSP-73, and DSP... are multiple consignors, consignees or freight forwarders, and all the required information cannot...

  14. 27 CFR 21.126 - Safrole.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Safrole. 21.126 Section 21.126 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS FORMULAS FOR DENATURED ALCOHOL AND RUM Specifications for Denaturants § 21.126 Safrole....

  15. 29 CFR 570.126 - Parental exemption.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 3 2010-07-01 2010-07-01 false Parental exemption. 570.126 Section 570.126 Labor... Provisions of the Fair Labor Standards Act of 1938, as Amended Exemptions § 570.126 Parental exemption. By... place of a parent may employ his own child or a child in his custody under the age of 16 years in...

  16. 5 CFR 185.126 - Evidence.

    Science.gov (United States)

    2010-01-01

    ... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Evidence. 185.126 Section 185.126 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS PROGRAM FRAUD CIVIL REMEDIES § 185.126 Evidence. (a) The ALJ shall determine the admissibility of evidence. (b) Except as provided...

  17. 49 CFR 1.26 - Secretarial succession.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 1 2010-10-01 2010-10-01 false Secretarial succession. 1.26 Section 1.26 Transportation Office of the Secretary of Transportation ORGANIZATION AND DELEGATION OF POWERS AND DUTIES Office of the Secretary § 1.26 Secretarial succession. (a) The following officials, in the order...

  18. 46 CFR 126.220 - Description.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Description. 126.220 Section 126.220 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OFFSHORE SUPPLY VESSELS INSPECTION AND CERTIFICATION Certificate of Inspection § 126.220 Description. The Certificate of Inspection issued to an OSV specifies...

  19. Nanocrystalline cerium oxide materials for solid fuel cell systems

    Energy Technology Data Exchange (ETDEWEB)

    Brinkman, Kyle S

    2015-05-05

    Disclosed are solid fuel cells, including solid oxide fuel cells and PEM fuel cells that include nanocrystalline cerium oxide materials as a component of the fuel cells. A solid oxide fuel cell can include nanocrystalline cerium oxide as a cathode component and microcrystalline cerium oxide as an electrolyte component, which can prevent mechanical failure and interdiffusion common in other fuel cells. A solid oxide fuel cell can also include nanocrystalline cerium oxide in the anode. A PEM fuel cell can include cerium oxide as a catalyst support in the cathode and optionally also in the anode.

  20. Divalent fluoride doped cerium fluoride scintillator

    Science.gov (United States)

    Anderson, David F.; Sparrow, Robert W.

    1991-01-01

    The use of divalent fluoride dopants in scintillator materials comprising cerium fluoride is disclosed. The preferred divalent fluoride dopants are calcium fluoride, strontium fluoride, and barium fluoride. The preferred amount of divalent fluoride dopant is less than about two percent by weight of the total scintillator. Cerium fluoride scintillator crystals grown with the addition of a divalent fluoride have exhibited better transmissions and higher light outputs than crystals grown without the addition of such dopants. These scintillators are useful in radiation detection and monitoring applications, and are particularly well suited for high-rate applications such as positron emission tomography (PET).

  1. CHEMICAL BEHAVIOR OF CERIUM ELEMENT IN ROCK WEATHERING SYSTEM

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    A study on existing valence state and chemical behavior of cerium element in two categories of rock weathering system in China has been carried out. In the granitoid weathering crust of Southern China,cerium as tetravalent hydroxide absorbed on clay minerals occupies 62.58 % of total amount of cerium and the cerium partitioning in the phase is 69.58 %. The depositing cerium stops its mobility downward, resulting in rare earth partitioning variation, the light rare earth partitioning is high at upper layer of weathering crust, the heavy rare earth partitioning is high at bottom layer of weathering crust, and the extracted product exists cerium lose effect. For Mn2+ as reducing agent existing in black weathering earth of Maoniuping rare earth ore,cerium is trivalent and absorbed on Mn-Fe oxide as colloid phase sediment. Colloid sediment phase can be divided into Mn-Fe combined phase and hydroxide sediment phase with cerium contents of 19.77% and 48.30%, and their cerium partitionings are 80.72% and 37.38% respectively. The Mn-Fe combined phase can selectively absorb cerium.

  2. 7 CFR 4279.126 - Loan terms.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 15 2010-01-01 2010-01-01 false Loan terms. 4279.126 Section 4279.126 Agriculture... Loan terms. (a) The maximum repayment for loans on real estate will not exceed 30 years; machinery and... or 15 years, whichever is less; and working capital repayment will not exceed 7 years. The term for...

  3. 40 CFR 92.126 - Test run.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Test run. 92.126 Section 92.126 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR... measurement equipment, etc.). (3) Start the particulate dilution tunnel, the sample pumps, the engine...

  4. 37 CFR 41.126 - Arbitration.

    Science.gov (United States)

    2010-07-01

    ... 37 Patents, Trademarks, and Copyrights 1 2010-07-01 2010-07-01 false Arbitration. 41.126 Section... COMMERCE PRACTICE BEFORE THE BOARD OF PATENT APPEALS AND INTERFERENCES Contested Cases § 41.126 Arbitration. (a) Parties to a contested case may resort to binding arbitration to determine any issue in...

  5. 7 CFR 12.6 - Administration.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 1 2010-01-01 2010-01-01 false Administration. 12.6 Section 12.6 Agriculture Office....6 Administration. (a) General. A determination of ineligibility for benefits in accordance with the... making such determinations, as provided in this section. (b) Administration by FSA. (1) The provisions...

  6. Synthesis of Cerium-Doped Titania Nanoparticles and Nanotubes.

    Science.gov (United States)

    Cao, Wei; Suzuki, Takuya; Elsayed-Ali, Hani E; Abdel-Fattah, Tarek M

    2015-03-01

    Cerium-doped titania nanoparticles and nanotubes were synthesized via hydrothermal processes. X-Ray Diffraction revealed that cerium-doped titania nanoparticles have an anatase crystal structure, while cerium-doped titania nanotubes have an H2Ti3O7-type structure. Scanning electron microscopy and high resolution transmission electron microscopy showed that both types of titania are well crystallized with relatively uniform size distribution. The photocatalytic degradation of methylthioninium chloride known as methylene blue dye was tested and both cerium-doped titania nanoparticles and nanotubes. The preliminary photocatalytic degradation of Methylene Blue data showed significantly improved visible light photocatalytic activities as compared to commercial titania powders.

  7. Dicty_cDB: VHP126 [Dicty_cDB

    Lifescience Database Archive (English)

    Full Text Available VH (Link to library) VHP126 (Link to dictyBase) - - - Contig-U16379-1 VHP126P (Link to Original site) VHP1...26F 683 VHP126Z 765 VHP126P 1428 - - Show VHP126 Library VH (Link to library) Clone ID VHP1...e URL http://dictycdb.biol.tsukuba.ac.jp/CSM/VH/VHP1-B/VHP126Q.Seq.d/ Representative seq. ID VHP1...26P (Link to Original site) Representative DNA sequence >VHP126 (VHP126Q) /CSM/VH/VHP1-B/VHP1...Sequences producing significant alignments: (bits) Value VHP126 (VHP126Q) /CSM/VH/VHP1-B/VHP126Q.Seq.d/ 2750

  8. Cerium and jojoba in engines?; Cerium et jojoba dans les moteurs?

    Energy Technology Data Exchange (ETDEWEB)

    Massy-Delhotel, E.

    1996-10-01

    The Belgium company CreaTel proposes a new system, called Forac, which can lead to a 10% reduction of fuel consumption in thermal engines together with a quasi-complete reduction of CO, HC, NOx pollutants and CO{sub 2} particulates emission. The system comprises a steam production device and an admission pipe with a cerium alloy whorl inside. The steam produced is mixed with the admission air and tears cerium particles from the inside of the admission pipe to the combustion chamber. The cerium particles act as a catalyst which favours the complete combustion of the fuel. The same company proposes also lubricant additives made from liquid jojoba wax which allow the reduction of pollutant emissions, fuel consumption and noise emissions of diesel engines. (J.S.)

  9. Effects of Cerium Oxide Nanoparticles on Sorghum Plant Traits

    Science.gov (United States)

    Mu, L.; Chen, Y.; Darnault, C. J. G.; Rauh, B.; Kresovich, S.; Korte, C.

    2015-12-01

    Nanotechnology and nanomaterials are considered as the development of the modern science. However, besides with that wide application, nanoparticles arouse to the side effects on the environment and human health. As the catalyst of ceramics and fuel industry, Cerium (IV) oxide nanoparticles (CeO2 NPs) can be found in the environment following their use and life-cycle. Therefore, it is critical to assess the potential effects that CeO2 NPs found in soils may have on plants. In this study, CeO2 NPs were analyzed for the potential influence on the sorghum [Sorghum bicolor (L.) Moench] (Reg. no. 126) (PI 154844) growth and traits. The objectives of this research were to determine whether CeO2 NPs impact the sorghum germination and growth characteristics. The sorghum was grown in the greenhouse located at Biosystems Research Complex, Clemson University under different CeO2 NPs treatments (0mg; 100mg; 500mg; 1000mg CeO2 NPs/Kg soil) and harvested around each month. At the end of the each growing period, above ground vegetative tissue was air-dried, ground to 2mm particle size and compositional traits estimated using near-infrared spectroscopy. Also, the NPK value of the sorghum tissue was tested by Clemson Agriculture Center. After the first harvest, the result showed that the height of above ground biomass under the nanoparticles stress was higher than that of control group. This difference between the control and the nanoparticles treatments was significant (F>F0.05; LSD). Our results also indicated that some of the compositional traits were impacted by the different treatments, including the presence and/or concentrations of the nanoparticles.

  10. Dicty_cDB: SLB126 [Dicty_cDB

    Lifescience Database Archive (English)

    Full Text Available SL (Link to library) SLB126 (Link to dictyBase) slb126 - - Contig-U16381-1 SLB126E ...(Link to Original site) - - - - - - SLB126E 454 Show SLB126 Library SL (Link to library) Clone ID SLB126 (Li...nk to dictyBase) Atlas ID slb126 NBRP ID - dictyBase ID - Link to Contig Contig-U16381-1 Original site URL h...ttp://dictycdb.biol.tsukuba.ac.jp/CSM/SL/SLB1-B/SLB126Q.Seq.d/ Representative seq. ID SLB...126E (Link to Original site) Representative DNA sequence >SLB126 (SLB126Q) /CSM/SL/SLB1-B/SLB126Q.Se

  11. Structural, optical, morphological and dielectric properties of cerium oxide nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Prabaharan, Devadoss Mangalam Durai Manoharadoss [Department of Physics, NPR College of Engineering and Technology, Natham, Dindigul, Tamil Nadu (India); Sadaiyandi, Karuppasamy [Department of Physics, Alagappa Government Arts College, Karaikudi, Sivaganga, Tamil Nadu (India); Mahendran, Manickam [Department of Physics, Thiagarajar College of Engineering, Madurai, Tamil Nadu (India); Sagadevan, Suresh, E-mail: duraiphysics2011@gmail.com [Department of Physics, AMET University (India)

    2016-03-15

    Cerium oxide (CeO{sub 2}) nanoparticles were prepared by the precipitation method. The average crystallite size of cerium oxide nanoparticles was calculated from the X-ray diffraction (XRD) pattern and found to be 11 nm. The FT-IR spectrum clearly indicated the strong presence of cerium oxide nanoparticles. Raman spectrum confirmed the cubic nature of the cerium oxide nanoparticles. The Scanning Electron Microscopy (SEM) analysis showed that the nanoparticles agglomerated forming spherical-shaped particles. The Transmission Electron Microscopic (TEM) analysis confirmed the prepared cerium oxide nanoparticles with the particle size being found to be 16 nm. The optical absorption spectrum showed a blue shift by the cerium oxide nanoparticles due to the quantum confinement effect. The dielectric properties of cerium oxide nanoparticles were studied for different frequencies at different temperatures. The dielectric constant and the dielectric loss of the cerium oxide nanoparticles decreased with increase in frequency. The AC electrical conductivity study revealed that the conduction depended on both the frequency and the temperature. (author)

  12. Formation and characterization of cerium conversion coatings on magnesium alloy

    Institute of Scientific and Technical Information of China (English)

    LI Lingjie; LEI Jinglei; YU Shenghai; TIAN Yujing; JIANG Qiquan; PAN Fusheng

    2008-01-01

    Chemical conversion treatment by rare earth metal salt solution was considered as an alternative to chromium chemical conversion treatment to improve the corrosion resistance of magnesium alloys. In this study, cerium conversion coatings formed on AZ31 magnesium alloy were characterized and the formation mechanism was discussed. X-ray photoelectron spectroscopy (XPS) analysis showed that cerium conversion coating consisted of cerium hydroxides/oxides, in which both tetravalent cerium Ce(IV) and trivalent cerium Ce(III) species co-existed. Cerium conversion coating was a two-layer structure. Atomic force microscopy (AFM) images revealed that the morphology of the inside layer was different from that of the outside one, which was responsible for the inherent adhesive weakness of the coating. Corrosion potential (Ecorr) measurements indicated that poor adhesion limited the improvement of the corrosion resistance of the coating. During the treating process, the increased pH value of the cerium salt solution led to the precipitation of cerium hydroxides/oxides. The formation kinetics of the coating followed a parabolic curve.

  13. Radiation induced color centers in cerium-doped and cerium-free multicomponent silicate glasses

    Institute of Scientific and Technical Information of China (English)

    傅鑫杰; 宋力昕; 李家成

    2014-01-01

    The effect of doped cerium on the radiation-resistance behavior of silicate glass was investigated in our work. The ultra-violet-visible absorption spectra and electron paramagnetic resonance (EPR) spectra were obtained after the cerium-rich and ce-rium-free multicomponent silicate glasses (K509 and K9) were irradiated by gamma rays with a dose range from 10 to 1000 kGy. The results showed that E’ center, oxygen deficient center (ODC) and non-bridging oxygen hole center (HC1 and HC2) were induced in K9 and K509 glasses after radiation. The concentrations of all color centers presented an exponential growth with the increase of the gamma dose. Moreover, the concentration of HC1 and HC2 in cerium-doped K509 glass was much lower than that in cerium-free K9 glass at the same dose of radiation, which could be attributed to the following mechanism:Ce3+ions capturing holes then forming Ce3++centers inhibited the formation of hole trapped color centers (HC1 and HC2) and Ce4+ions capturing electrons to form Ce3+centers suppressed the formation of electron trapped color centers like E’ center.

  14. Ultrathin, epitaxial cerium dioxide on silicon

    International Nuclear Information System (INIS)

    It is shown that ultrathin, highly ordered, continuous films of cerium dioxide may be prepared on silicon following substrate prepassivation using an atomic layer of chlorine. The as-deposited, few-nanometer-thin Ce2O3 film may very effectively be converted at room temperature to almost fully oxidized CeO2 by simple exposure to air, as demonstrated by hard X-ray photoemission spectroscopy and X-ray diffraction. This post-oxidation process essentially results in a negligible loss in film crystallinity and interface abruptness

  15. Ultrathin, epitaxial cerium dioxide on silicon

    OpenAIRE

    Flege, Jan Ingo; Kaemena, Björn; Höcker, Jan; Bertram, Florian; Wollschläger, Joachim; Schmidt, Thomas; Falta, Jens

    2014-01-01

    It is shown that ultrathin, highly ordered, continuous films of cerium dioxide may be prepared on silicon following substrate prepassivation using an atomic layer of chlorine. The as-deposited, few-nanometer-thin Ce2O3 film may very effectively be converted at room temperature to almost fully oxidized CeO2 by simple exposure to air, as demonstrated by hard X-ray photoemission spectroscopy and X-ray diffraction. This post-oxidation process essentially results in a negligible loss in film cryst...

  16. Crystal structure of cerium(4) - dicesium trisulfate

    International Nuclear Information System (INIS)

    Cerium(4) - dicesium trisulfate is investigated by the X-ray diffraction method. Parameters of a monoclinic cell equal: a = 9.772(2), b = 16.797(2), c = 14.812(1)A, β 96.40(1), sp.gr. P21. The structure is formed by interchanging of anion [Ce4(SO4)128-]∞ and cation (Cs+) layers arranged parallel (101). Atoms Ce and Cs are arranged according to the law of a cubic close packing. Coordination polyhedron Ce1 and Ce2 is the two-hat trigonal prism, nine vertices Ce3 and Ce4 are one-hat antiprism

  17. Ultrathin, epitaxial cerium dioxide on silicon

    Science.gov (United States)

    Flege, Jan Ingo; Kaemena, Björn; Höcker, Jan; Bertram, Florian; Wollschläger, Joachim; Schmidt, Thomas; Falta, Jens

    2014-03-01

    It is shown that ultrathin, highly ordered, continuous films of cerium dioxide may be prepared on silicon following substrate prepassivation using an atomic layer of chlorine. The as-deposited, few-nanometer-thin Ce2O3 film may very effectively be converted at room temperature to almost fully oxidized CeO2 by simple exposure to air, as demonstrated by hard X-ray photoemission spectroscopy and X-ray diffraction. This post-oxidation process essentially results in a negligible loss in film crystallinity and interface abruptness.

  18. Photodissociation of Cerium Oxide Nanocluster Cations.

    Science.gov (United States)

    Akin, S T; Ard, S G; Dye, B E; Schaefer, H F; Duncan, M A

    2016-04-21

    Cerium oxide cluster cations, CexOy(+), are produced via laser vaporization in a pulsed nozzle source and detected with time-of-flight mass spectrometry. The mass spectrum displays a strongly preferred oxide stoichiometry for each cluster with a specific number of metal atoms x, with x ≤ y. Specifically, the most prominent clusters correspond to the formula CeO(CeO2)n(+). The cluster cations are mass selected and photodissociated with a Nd:YAG laser at either 532 or 355 nm. The prominent clusters dissociate to produce smaller species also having a similar CeO(CeO2)n(+) formula, always with apparent leaving groups of (CeO2). The production of CeO(CeO2)n(+) from the dissociation of many cluster sizes establishes the relative stability of these clusters. Furthermore, the consistent loss of neutral CeO2 shows that the smallest neutral clusters adopt the same oxidation state (IV) as the most common form of bulk cerium oxide. Clusters with higher oxygen content than the CeO(CeO2)n(+) masses are present with much lower abundance. These species dissociate by the loss of O2, leaving surviving clusters with the CeO(CeO2)n(+) formula. Density functional theory calculations on these clusters suggest structures composed of stable CeO(CeO2)n(+) cores with excess oxygen bound to the surface as a superoxide unit (O2(-)). PMID:27035210

  19. Dicty_cDB: AHB126 [Dicty_cDB

    Lifescience Database Archive (English)

    Full Text Available AH (Link to library) AHB126 (Link to dictyBase) - - - Contig-U16336-1 AHB126P (Link... to Original site) AHB126F 598 AHB126Z 500 AHB126P 1078 - - Show AHB126 Library AH (Link to library) Clone ID AHB126 (Link to dict...yBase) Atlas ID - NBRP ID - dictyBase ID - Link to Contig Contig-U16336-1 Original site URL http://dict...RGIRNHKKNETKFINQCINEIKEELKGDMQKKTVAVQKLTYIQMLGFDI SWASFKIVEVMSCNKFSSKRIGYLAASQSFNEGTDVIVLATHQIRKDFLSSNQSEAYLAL NCLSNICT...KKNETKFINQCINEIKEELKGDMQKKTVAVQKLTYIQMLGFDI SWASFKIVEVMSCNKFSSKRIGYLAASQSFNEGTDVIVLATHQIRKDFLSSNQSEAYLAL NCLSNICT

  20. 40 CFR 93.126 - Exempt projects.

    Science.gov (United States)

    2010-07-01

    ... in 23 CFR part 771. Air Quality Continuation of ride-sharing and van-pooling promotion activities at... that action. Noise attenuation. Emergency or hardship advance land acquisitions (23 CFR 710.503... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Exempt projects. 93.126 Section...

  1. 32 CFR 552.126 - Definitions.

    Science.gov (United States)

    2010-07-01

    ... CEMETERIES REGULATIONS AFFECTING MILITARY RESERVATIONS Control of Firearms, Ammunition and Other Dangerous Weapons on Fort Gordon § 552.126 Definitions. For the purpose of this part, the following definitions... offensive or defensive weapon. Devices of this type include but are not limited to: (1) “Constant...

  2. 33 CFR 157.126 - Pumps.

    Science.gov (United States)

    2010-07-01

    ... Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) POLLUTION RULES FOR... Washing (COW) System on Tank Vessels Design, Equipment, and Installation § 157.126 Pumps. (a) Crude oil must be supplied to the COW machines by COW system pumps or cargo pumps. (b) The pumps under...

  3. 37 CFR 1.26 - Refunds.

    Science.gov (United States)

    2010-07-01

    ... by electronic funds transfer (31 U.S.C. 3332 and 31 CFR part 208), or instruct the Office that... GENERAL RULES OF PRACTICE IN PATENT CASES General Provisions Fees and Payment of Money § 1.26 Refunds. (a... check, electronic funds transfer, credit to a deposit account, etc.). Generally, reexamination...

  4. Fire retardancy of emulsion polymerized poly (methyl methacrylate)/cerium(IV) dioxide and polystyrene/cerium(IV) dioxide nanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Cai, Guipeng [Department of Chemistry and Fire Retardant Research Facility, Marquette University, PO Box 1881, Milwaukee, WI 53201 (United States); Lu, Hongdian [Department of Chemical and Materials Engineering, Hefei University, Hefei, Anhui 230022 (China); Zhou, You; Hao, Jianwei [School of Material Science and Engineering, Beijing Institute of Technology, Beijing 100081 (China); Wilkie, Charles A., E-mail: charles.wilkie@marquette.edu [Department of Chemistry and Fire Retardant Research Facility, Marquette University, PO Box 1881, Milwaukee, WI 53201 (United States)

    2012-12-10

    Highlights: Black-Right-Pointing-Pointer We prepare PMMA and PS containing ceria. Black-Right-Pointing-Pointer Characterization by XRD and TEM shows that some of the ceria is well-dispersed in the polymers. Black-Right-Pointing-Pointer The addition of ceria to both polymers leads to reduced thermal stability. Black-Right-Pointing-Pointer In PMMA, the fire retardancy is enhanced but there is little effect in PS. - Abstract: In situ emulsion polymerization was employed to obtain poly (methyl methacrylate) (PMMA)/cerium(IV) dioxide and polystyrene (PS)/cerium(IV) dioxide nanocomposites at two different cerium(IV) dioxide loadings (2.3 wt% and 4.6 wt%). Transmission electron microscope results indicated uniform dispersion of cerium (IV) dioxide in the polymer matrix. Both PMMA and PS nanocomposites exhibit lower thermal stability than the pristine polymers. Microscale combustion calorimeter (MCC) and cone calorimetry are used to evaluate the fire retardancy of the polymer nanocomposites. PMMA/cerium(IV) dioxide showed significant heat release rate (HRR) reduction at low loadings (<5 wt%), while PS/cerium(IV) dioxide exhibits less HRR reduction at the same loadings. An explanation of the role of cerium (IV) dioxide in fire retardancy of polymer/ceria nanocomposites based on XPS results is suggested.

  5. Preparing Process of Cerium Acetate and Rare Earth Acetate

    Institute of Scientific and Technical Information of China (English)

    Qiao Jun; Ma Ying; Xu Yanhui; Zhang Jun; Chang Shu; Hao Xianku

    2004-01-01

    Preparing process was presented and the influences of concentration of acetic acid, reaction temperature, the ratio of cerium carbonate and acetic acid, heat preservation time to the yield of cerium acetate were discussed.The crystalline cerium acetate and rare earth acetate such as ( La, Ce, Pr, Nd) (Ac) 3, ( Ce, Pr, Nd) (Ac) 3, ( Pr, Nd, Er,Y) (Ac) 3 and yttrium acetate were prepared under this condition.The shape, structure and composition of the crystals were determined by the methods of SEM, TG-DTA, X-ray diffraction and chemical analysis.The optimum prepared conditions of cerium acetate were described.This prepared process has characteristics such as simple process route, low cost, high yield, good quality, no pollution to environment, etc.

  6. Improvement in corrosion resistance of magnesium coating with cerium treatment

    Institute of Scientific and Technical Information of China (English)

    Samia Ben Hassen; Latifa Bousselmi; Patricc Bercot; El Mustafa Rezrazi; Ezzeddine Triki

    2009-01-01

    Corrosion protection afforded by a magnesium coating treated in cerium salt solution on steel substrate was investigated using open circuit potential, polarization curves, and electrochemical impedance spectroscopy (EIS) in 0.005 M sodium chloride solution (NaCl). The morphology of the surface was characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD). The cerium treated coating was obtained by immersion in CeCl3 solution. The results showed that the corrosion resistance of the treated magnesium coating was improved. The corrosion potential of the treated coating was found to be nobler than that of the untreated magnesium coating and the corrosion current decreased significantly. Impedance results showed that the cerium treatment increased corrosion protection. The improvement of anti-corrosion properties was ataibuted to the formation of cerium oxides and hydroxides that gave to a physical barrier effect.

  7. A contribution to the radiologic findings in cerium pneumoconiosis

    International Nuclear Information System (INIS)

    Report on a 69 year old man, who had been employed as photographer in the printing industry and who had been exposed to Cerium for 40 years. The chest X-ray which was performed 9 years after the end of the exposure displayes striate densities of the lungs, which must be considered as a late stage of Cerium-pneumoconiosis. The changes which were found fulfill the code 't 1/0 RO, RM, RU, LO, LM, LU, p 0/1 RO, RM, LO, LM, em, tbu' according to the 'ILO U/C 1971 classification of pneumoconiosis'. The diagnosis could be substantiated by measureing Cerium in the lung parenchyma qualitatively and quantitatively using neutrone activating analysis. The radiolgic findings of the Cerium pneumoconiosis are discussed. (orig.)

  8. Heteroaggregation of cerium oxide nanoparticles and nanoparticles of pyrolyzed biomass

    Science.gov (United States)

    Heteroaggregation with indigenous particles is an important process controlling the mobility of engineered nanomaterials in the environment. We studied heteroaggregation of cerium oxide nanoparticles (n-CeO2), which are widely used commercially, with nanoparticles of pyrogenic carbonaceous material ...

  9. miR-126 and miR-126*: New Players in Cancer

    Directory of Open Access Journals (Sweden)

    Jeannette Meister

    2010-01-01

    Full Text Available Cancer progression is characterized by autarky in growth signals, insensitivity to growth-restrictive signals, evasion of apoptosis, a limitless potential to replicate, sustained angiogenesis, and tissue invasion, including metastasis. The regulation of these cellular processes relies on a fine-tuned control of molecular signal cascades. In recent years, short noncoding RNAs termed microRNAs (miRNAs have been described as a novel class of molecular regulators. These affect various signaling cascades during the progression of neoplastic diseases by the regulation of gene expression on the post-transcriptional level. The novel endothelial cell–derived secreted protein epidermal growth factor–like domain 7 (EGFL7 has been suggested to control vascular tubulogenesis. Further, the two biologically active miRNAs miR-126 and its complement miR-126*, which are encoded by intron 7 of the egfl7 gene, have been described to mediate vascular functions. Knock-out studies in zebrafish and mice suggested a major role of miR-126 in angiogenesis and vascular integrity, which was mediated by the repression of inhibitors of VEGF-induced proliferation in endothelial cells. Recent studies revealed the distribution and function of miR-126 and miR-126* in various types of cancer, and assigned a role to both miRNAs as suppressors of tumor formation. Indeed, miR-126 and miR-126* have been reported to impair cancer progression through signaling pathways that control tumor cell proliferation, migration, invasion, and survival. Conversely, miR-126 and miR-126* may have a supportive role in the progression of cancer as well, which might be mediated by the promotion of blood vessel growth and inflammation. In this work, we will summarize the current knowledge on functions of miR-126/miR-126* that are relevant for cancer formation, and we will discuss their potential clinical use as predictive markers of survival and application as novel therapeutic targets for the

  10. miR-126 and miR-126*: new players in cancer.

    Science.gov (United States)

    Meister, Jeannette; Schmidt, Mirko H H

    2010-01-01

    Cancer progression is characterized by autarky in growth signals, insensitivity to growth-restrictive signals, evasion of apoptosis, a limitless potential to replicate, sustained angiogenesis, and tissue invasion, including metastasis. The regulation of these cellular processes relies on a fine-tuned control of molecular signal cascades. In recent years, short noncoding RNAs termed microRNAs (miRNAs) have been described as a novel class of molecular regulators. These affect various signaling cascades during the progression of neoplastic diseases by the regulation of gene expression on the post-transcriptional level. The novel endothelial cell-derived secreted protein epidermal growth factor-like domain 7 (EGFL7) has been suggested to control vascular tubulogenesis. Further, the two biologically active miRNAs miR-126 and its complement miR-126*, which are encoded by intron 7 of the egfl7 gene, have been described to mediate vascular functions. Knock-out studies in zebrafish and mice suggested a major role of miR-126 in angiogenesis and vascular integrity, which was mediated by the repression of inhibitors of VEGF-induced proliferation in endothelial cells. Recent studies revealed the distribution and function of miR-126 and miR-126* in various types of cancer, and assigned a role to both miRNAs as suppressors of tumor formation. Indeed, miR-126 and miR-126* have been reported to impair cancer progression through signaling pathways that control tumor cell proliferation, migration, invasion, and survival. Conversely, miR-126 and miR-126* may have a supportive role in the progression of cancer as well, which might be mediated by the promotion of blood vessel growth and inflammation. In this work, we will summarize the current knowledge on functions of miR-126/miR-126* that are relevant for cancer formation, and we will discuss their potential clinical use as predictive markers of survival and application as novel therapeutic targets for the treatment of neoplastic

  11. Cerium fluoride crystals for calorimetry at LHC

    International Nuclear Information System (INIS)

    High-resolution homogeneous calorimetry is fully justified for part of the physics program at the Large Hadron Collider (LHC). The main design features of proposed CeF3 crystals for calorimetry for LHC are discussed. The severe constraints LHC imposes on detectors make the use of 'classical' crystals impossible. Therefore, a large R and D effort has been undertaken by the 'Crystal Clear' collaboration in order to find new, dense, fast and radiation hard crystals. A good candidate, cerium fluoride, has been identified and studied. It is interesting at this stage to review the specifications of scintillators for LHC and to see how well available data on CeF3 luminescence, decay time, light yield, optical transmission and resistance to radiation meet them. Milestones to reach before starting a large scale crystal production in view of the eventual construction of a calorimeter, are also discussed. (author) 15 refs., 15 figs., 1 tab

  12. Further results on cerium fluoride crystals

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, S.; Auffray, E.; Aziz, T.; Baccaro, S.; Banerjee, S.; Bareyre, P.; Barone, L.E.; Borgia, B.; Boutet, D.; Burq, J.P.; Chemarin, M.; Chipaux, R.; Dafinei, I.; D' Atanasio, P.; De Notaristefani, F.; Dezillie, B.; Dujardin, C.; Dutta, S.; Faure, J.L.; Fay, J.; Ferrere, D.; Francescangeli, O.; Fuchs, B.A.; Ganguli, S.N.; Gillespie, G.; Goyot, M.; Gupta, S.K.; Gurtu, A.; Heck, J.; Herve, A.; Hillemanns, H.; Holdener, F.; Ille, B.; Joensson, L.; Kierstead, J.; Krenz, W.; Kway, W.; Le Goff, J.M.; Lebeau, M.; Lebrun, P.; Lecoq, P.; Lemoigne, Y.; Loomis, G.; Lubelsmeyer, K.; Madjar, N.; Majni, G.; El Mamouni, H.; Mangla, S.; Mares, J.A.; Martin, J.P.; Mattioli, M.; Mauger, G.J.; Mazumdar, K.; Mengucci, P.; Merlo, J.P.; Moine, B.; Nikl, N.; Pansart, J.P.; Pedrini, C.; Poinsignon, J.; Polak, K.; Raghavan, R.; Rebourgeard, P.; Rinaldi, D.; Rosa, J.; Rosowsky, A.; Sahuc, P.; Samsonov, V.; Sarkar, S.; Schegelski, V.; Schmitz, D.; Schneegans, M.; Seliverstov, D.; Stoll, S.; Sudhakar, K.; Sven; Crystal Clear Collaboration

    1993-08-15

    A systematic investigation of the properties of cerium fluoride monocrystals has been performed by the 'Crystal Clear' collaboration in view of a possible use of such crystals for the construction of high precision electromagnetic calorimeters for the future generation of high luminosity accelerators. A large sample of different crystals grown by several producers has been studied. The spectroscopic characteristics, the transmission, luminescence and excitation spectra and the decay time curves are analysed. The light yield of the different crystals is measured with photomultipliers and Si photodiodes and compared to reference standards like BGO and NaI(Tl). The radiation damage behaviour is then presented for [gamma] and neutron irradiations, at different doses and dose rates, including thermal and optical bleaching. (orig.)

  13. Cerium intermetallics CeTX. Review III

    Energy Technology Data Exchange (ETDEWEB)

    Poettgen, Rainer; Janka, Oliver [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie; Chevalier, Bernard [Bordeaux Univ., Pessac (France). Inst. de Chimie de la Matiere Condensee de Bordeaux

    2016-05-01

    The structure-property relationships of CeTX intermetallics with structures other than the ZrNiAl and TiNiSi type are systematically reviewed. These CeTX phases form with electron-poor and electron-rich transition metals (T) and X = Mg, Zn, Cd, Hg, Al, Ga, In, Tl, Si, Ge, Sn, Pb, P, As, Sb, and Bi. The review focusses on the crystal chemistry, the chemical bonding peculiarities, and the magnetic and transport properties. Furthermore {sup 119}Sn Moessbauer spectroscopic data, high-pressure studies, hydrogenation reactions and the formation of solid solutions are reviewed. This paper is the third of a series of four reviews on equiatomic intermetallic cerium compound [Part I: R. Poettgen, B. Chevalier, Z. Naturforsch. 2015, 70b, 289; Part II: R. Poettgen, B. Chevalier, Z. Naturforsch. 2015, 70b, 695].

  14. 46 CFR 126.110 - Inspection after accident.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Inspection after accident. 126.110 Section 126.110... CERTIFICATION General § 126.110 Inspection after accident. (a) The owner or operator of an OSV shall make the vessel available for inspection by a marine inspector— (1) Each time an accident occurs, or a defect...

  15. 34 CFR 303.126 - Payor of last resort.

    Science.gov (United States)

    2010-07-01

    ... 34 Education 2 2010-07-01 2010-07-01 false Payor of last resort. 303.126 Section 303.126 Education Regulations of the Offices of the Department of Education (Continued) OFFICE OF SPECIAL EDUCATION AND... DISABILITIES State Application for a Grant Statement of Assurances § 303.126 Payor of last resort....

  16. 27 CFR 26.126 - Taxpayment in Puerto Rico.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Taxpayment in Puerto Rico. 26.126 Section 26.126 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU... Articles Purchased by Tourists in Puerto Rico § 26.126 Taxpayment in Puerto Rico. Liquors upon which...

  17. 22 CFR 126.12 - Continuation in force.

    Science.gov (United States)

    2010-04-01

    ... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Continuation in force. 126.12 Section 126.12... PROVISIONS § 126.12 Continuation in force. All determinations, authorizations, licenses, approvals of... previous provisions of this subchapter, continue in full force and effect until or unless modified,...

  18. Inhibition of pH fronts in corrosion cells due to the formation of cerium hydroxide

    NARCIS (Netherlands)

    Soestbergen, M. van; Erich, S.J.F.; Huinink, H.P.; Adan, O.C.G.

    2013-01-01

    The effect of cerium-based corrosion inhibitors on the pH front between the alkaline cathode and acidic anode in corrosion cells has been studied. The cerium component of these inhibitors can affect the pH front since it precipitates in an alkaline environment as cerium hydroxide, which is important

  19. Potential for recovery of cerium contained in automotive catalytic converters

    Science.gov (United States)

    Bleiwas, Donald I.

    2013-01-01

    Catalytic converters (CATCONs) are required by Federal law to be installed in nearly all gasoline- and diesel-fueled onroad vehicles used in the United States. About 85 percent of the light-duty vehicles and trucks manufactured worldwide are equipped with CATCONs. Portions of the CATCONs (called monoliths) are recycled for their platinum-group metal (PGM) content and for the value of the stainless steel they contain. The cerium contained in the monoliths, however, is disposed of along with the slag produced from the recycling process. Although there is some smelter capacity in the United States to treat the monoliths in order to recover the PGMs, a great percentage of monoliths is exported to Europe and South Africa for recycling, and a lesser amount is exported to Japan. There is presently no commercial-scale capacity in place domestically to recover cerium from the monoliths. Recycling of cerium or cerium compounds from the monoliths could help ensure against possible global supply shortages by increasing the amount that is available in the supply chain as well as the number and geographic distribution of the suppliers. It could also reduce the amount of material that goes into landfills. Also, the additional supply could lower the price of the commodity. This report analyzes how much cerium oxide is contained in CATCONs and how much could be recovered from used CATCONs.

  20. Characterization of cerium fluoride nanocomposite scintillators

    Energy Technology Data Exchange (ETDEWEB)

    Stange, Sy [Los Alamos National Laboratory; Esch, Ernst I [Los Alamos National Laboratory; Brown, Leif O [Los Alamos National Laboratory; Couture, Aaron J [Los Alamos National Laboratory; Mckigney, Edward A [Los Alamos National Laboratory; Muenchausen, Ross E [Los Alamos National Laboratory; Del Sesto, Rico E [Los Alamos National Laboratory; Gilbertson, Robert D [Los Alamos National Laboratory; Mccleskey, T Mark [Los Alamos National Laboratory; Reifarth, Rene [Los Alamos National Laboratory

    2009-01-01

    Measurement of the neutron capture cross-sections of a number of short-lived isotopes would advance both pure and applied scientific research. These cross-sections are needed for calculation of criticality and waste production estimates for the Advanced Fuel Cycle Initiative, for analysis of data from nuclear weapons tests, and to improve understanding of nucleosynthesis. However, measurement of these cross-sections would require a detector with a faster signal decay time than those used in existing neutron capture experiments. Crystals of faster detector materials are not available in sufficient sizes and quantities to supply these large-scale experiments. Instead, we propose to use nanocomposite detectors, consisting of nanoscale particles of a scintillating material dispersed in a matrix material. We have successfully fabricated cerium fluoride (CeF{sub 3}) nanoparticles and dispersed them in a liquid matrix. We have characterized this scintillator and have measured its response to neutron capture. Results of the optical, structural, and radiation characterization will be presented.

  1. Chlorination and Carbochlorination of Cerium Oxide

    International Nuclear Information System (INIS)

    The chlorination and carbochlorination of cerium oxide were studied by thermogravimetry under controlled atmosphere (TG) in the 7000C 9500C temperature range.Both reactants and products were analyzed by X-ray diffraction (RX), scanning electronic microscopy (SEM) and energy dispersive spectroscopy (EDS). Thermodynamic calculations were performed by computer assisted software.The chlorination starts at a temperature close to 8000C.This reaction involves the simultaneous formation and evaporation of CeCl3.Both processes control the reaction rate and their kinetic may not be easily separated.The apparent chlorination activation energy in the 8500C-9500C temperature range is 172 to 5 kJ/ mole.Carbon transforms the CeO2-Cl2 into a more reactive system: CeO2-C-Cl2, where the effects of the carbon content, total flow rate and temperature were analyzed.The carbochlorination starting temperature is 7000C.This reaction is completed in one step controlled by mass transfer with an apparent activation energy of 56 to 5 kJ/mole in the 8500C-9500C temperature range

  2. Characterization of cerium fluoride nanocomposite scintillators

    International Nuclear Information System (INIS)

    Measurement of the neutron capture cross-sections of a number of short-lived isotopes would advance both pure and applied scientific research. These cross-sections are needed for calculation of criticality and waste production estimates for the Advanced Fuel Cycle Initiative, for analysis of data from nuclear weapons tests, and to improve understanding of nucleosynthesis. However, measurement of these cross-sections would require a detector with a faster signal decay time than those used in existing neutron capture experiments. Crystals of faster detector materials are not available in sufficient sizes and quantities to supply these large-scale experiments. Instead, we propose to use nanocomposite detectors, consisting of nanoscale particles of a scintillating material dispersed in a matrix material. We have successfully fabricated cerium fluoride (CeF3) nanoparticles and dispersed them in a liquid matrix. We have characterized this scintillator and have measured its response to neutron capture. Results of the optical, structural, and radiation characterization will be presented.

  3. Cerium Dioxide Thin Films Using Spin Coating

    Directory of Open Access Journals (Sweden)

    D. Channei

    2013-01-01

    Full Text Available Cerium dioxide (CeO2 thin films with varying Ce concentrations (0.1 to 0.9 M, metal basis were deposited on soda-lime-silica glass substrates using spin coating. It was found that all films exhibited the cubic fluorite structure after annealing at 500°C for 5 h. The laser Raman microspectroscopy and GAXRD analyses revealed that increasing concentrations of Ce resulted in an increase in the degree of crystallinity. FIB and FESEM images confirmed the laser Raman and GAXRD analyses results owing to the predicted increase in film thickness with increasing Ce concentration. However, porosity and shrinkage (drying cracking of the films also increased significantly with increasing Ce concentrations. UV-VIS spectrophotometry data showed that the transmission of the films decreased with increasing Ce concentrations due to the increasing crack formation. Furthermore, a red shift was observed with increasing Ce concentrations, which resulted in a decrease in the optical indirect band gap.

  4. Environmental Geochemistry of Cerium: Applications and Toxicology of Cerium Oxide Nanoparticles

    Directory of Open Access Journals (Sweden)

    Jessica T. Dahle

    2015-01-01

    Full Text Available Cerium is the most abundant of rare-earth metals found in the Earth’s crust. Several Ce-carbonate, -phosphate, -silicate, and -(hydroxide minerals have been historically mined and processed for pharmaceutical uses and industrial applications. Of all Ce minerals, cerium dioxide has received much attention in the global nanotechnology market due to their useful applications for catalysts, fuel cells, and fuel additives. A recent mass flow modeling study predicted that a major source of CeO2 nanoparticles from industrial processing plants (e.g., electronics and optics manufactures is likely to reach the terrestrial environment such as landfills and soils. The environmental fate of CeO2 nanoparticles is highly dependent on its physcochemical properties in low temperature geochemical environment. Though there are needs in improving the analytical method in detecting/quantifying CeO2 nanoparticles in different environmental media, it is clear that aquatic and terrestrial organisms have been exposed to CeO2 NPs, potentially yielding in negative impact on human and ecosystem health. Interestingly, there has been contradicting reports about the toxicological effects of CeO2 nanoparticles, acting as either an antioxidant or reactive oxygen species production-inducing agent. This poses a challenge in future regulations for the CeO2 nanoparticle application and the risk assessment in the environment.

  5. Cerium, manganese and cerium/manganese ceramic monolithic catalysts. Study of VOCs and PM removal

    Institute of Scientific and Technical Information of China (English)

    COLMAN-LERNER Esteban; PELUSO Miguel Andrs; SAMBETH Jorge; THOMAS Horacio

    2016-01-01

    Ceramic supported cerium, manganese and cerium-manganese catalysts were prepared by direct impregnation of aqueous precursor, and characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), Brunauer-Emmett-Teller method (BET), temperature programmed reduction (H2-TPR), X-ray photoelectron spectroscopy (XPS) acidity measurements and electrical conductivity. The catalytic activity was evaluated for volatile organic compounds (VOC) (ethanol, methyl ethyl ketone and toluene) oxidation. Additionally, catalysts were tested in particulate matter (PM) combustion. The characterization results indicated that Ce was in the form of Ce4+ and Ce3+, and Mn existed in the form of Mn4+and Mn3+on the surface of the Mn/AC sample and in the form of Mn4+ in the Ce/Mn/AC monolith. VOC oxidation results revealed that the Ce/Mn/AC sample showed an excellent performance compared with ceramic supported CeO2 (Ce/AC) and MnOx (Mn/AC) samples. The PM combustion was also higher on Ce/Mn/AC monoliths. The enhanced catalytic activity was mainly attributed to the Ce and Mn interaction which enhanced the acidity, conductiv-ity and the reducibility of the oxides.

  6. Cerium uptake by zeolite A synthesized from natural clinoptilolite tuffs

    International Nuclear Information System (INIS)

    Natural clinoptilolite tuffs from the Semnan region in Iran was used for the synthesis of zeolite A. The tuffs and synthesized zeolites were characterized by XRD and XRF. The sorption behavior of the synthesized zeolite toward cerium was studied. Using the Lagergren's equation, the absorption constant was calculated. The measured distribution coefficient values (Kd) indicated that cerium uptake is higher in lower initial concentrations, higher temperature and higher pH values. Thermodynamic parameters of the exchange were calculated through construction of ion-exchange isotherms at three temperatures of 298, 323 and 343 K. The dynamic absorption of cerium was also studied by passing the solution through a column in the presence and absence of sodium ions. (author)

  7. Synthesis and characterization of magnesium doped cerium oxide for the fuel cell application

    Science.gov (United States)

    Kumar, Amit; Kumari, Monika; Kumar, Mintu; Kumar, Sacheen; Kumar, Dinesh

    2016-05-01

    Cerium oxide has attained much attentions in global nanotechnology market due to valuable application for catalytic, fuel additive, and widely as electrolyte in solid oxide fuel cell. Doped cerium oxide has large oxygen vacancies that allow for greater reactivity and faster ion transport. These properties make cerium oxide suitable material for SOFCs application. Cerium oxide electrolyte requires lower operation temperature which shows improvement in processing and the fabrication technique. In our work, we synthesized magnesium doped cerium oxide by the co-precipitation method. With the magnesium doping catalytic reactivity of CeO2 was increased. Synthesized nanoparticle were characterized by the XRD and UV absorption techniques.

  8. The PL "violet shift" of cerium dioxide on silicon

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    CeO2 thin film was fabricated by dual ion beam epitaxial technique. The phenomenon of PL violet shift at room temperature was observed, and the distance of shift was about 65 nm. After the analysis of crystal structure and valence in the compound were carried out by XRD and XPS technique, it was concluded that the PL shift was related with valence of cerium ion in the oxides. When the valence of cerium ion varied from tetravalence to trivalence, the PL peak position would move from blue region to violet region and the phenomenon of "violet shift" was observed.

  9. Optical and electrical studies of cerium mixed oxides

    Energy Technology Data Exchange (ETDEWEB)

    Sherly, T. R., E-mail: trsherly@gmail.com [Post Graduate Department of Physics, Sanathana Dharma College, Alappuzha, Kerala (India); Raveendran, R. [Nanoscience Research Laboratory, Sree Narayana College, Kollam, Kerala 691001 (India)

    2014-10-15

    The fast development in nanotechnology makes enthusiastic interest in developing nanomaterials having tailor made properties. Cerium mixed oxide materials have received great attention due to their UV absorption property, high reactivity, stability at high temperature, good electrical property etc and these materials find wide applications in solid oxide fuel cells, solar control films, cosmetics, display units, gas sensors etc. In this study cerium mixed oxide compounds were prepared by co-precipitation method. All the samples were doped with Zn (II) and Fe (II). Preliminary characterizations such as XRD, SEM / EDS, TEM were done. UV - Vis, Diffuse reflectance, PL, FT-IR, Raman and ac conductivity studies of the samples were performed.

  10. Membrane assisted liquid-liquid extraction of cerium

    International Nuclear Information System (INIS)

    Membrane assisted liquid-liquid extraction of cerium was investigated, with emphasis placed on the study of the reaction chemistry and the kinetics of non-dispersive solvent extraction and stripping with microporous membranes. A bulk liquid membrane process was developed for the purification of cerium(IV) from sulfate solutions containing other rare earth elements. The cerium process was studied in both a flat sheet contained liquid membrane configuration and with hollow fibre contactors. Di-2-ethylhexyl phosphoric acid (DEHPA) was identified as a suitable extractant for cerium(IV) from sulfuric acid solution, with due consideration of factors such as extraction ability, resistance to degradation, solvent selectivity and potential for sulfate transfer into a strip solution. A detailed study of the extraction of cerium(IV) with DEHPA defined the extraction reaction chemistry. The Ce/DEHPA/sulfate system was also investigated with a flat sheet bulk liquid membrane configuration, using both sulfuric and hydrochloric acid as receiver solutions. These tests identified that hydrophobic membranes provide better mass transfer for extraction and hydrophilic membranes are better for stripping. The presence of an impurity, mono 2-ethylhexyl phosphoric acid (MEHPA), was found to have a dramatic accelerating effect on the rate of the chemical extraction reaction. This was attributed to its higher interfacial activity and population compared to DEHPA, and the fact that MEHPA was also found to be an active carrier for cerium(IV). The mass transfer rate of membrane assisted extraction and stripping of cerium, using hydrophobic and hydrophilic microporous membranes, respectively, was investigated using a modified Lewis-type cell. It was quantitatively demonstrated that the extraction process was mainly controlled by membrane diffusion and the stripping process was controlled by the chemical reaction rate, with membrane diffusion becoming important at low distribution coefficients

  11. Nanoparticulate cerium dioxide and cerium dioxide-titanium dioxide composite thin films on glass by aerosol assisted chemical vapour deposition

    International Nuclear Information System (INIS)

    Two series of composite thin films were deposited on glass by aerosol assisted chemical vapour deposition (AACVD)-nanoparticulate cerium dioxide and nanoparticulate cerium dioxide embedded in a titanium dioxide matrix. The films were analysed by a range of techniques including UV-visible absorption spectroscopy, X-ray diffraction, scanning electron microscopy and energy dispersive analysis by X-rays. The AACVD prepared films showed the functional properties of photocatalysis and super-hydrophilicity. The CeO2 nanoparticle thin films displaying photocatalysis and photo-induced hydrophilicity almost comparable to that of anatase titania.

  12. Purification of cerium, neodymium and gadolinium for low background experiments

    Science.gov (United States)

    Boiko, R. S.; Barabash, A. S.; Belli, P.; Bernabei, R.; Cappella, F.; Cerulli, R.; Danevich, F. A.; Incicchitti, A.; Laubenstein, M.; Mokina, V. M.; Nisi, S.; Poda, D. V.; Polischuk, O. G.; Tretyak, V. I.

    2014-01-01

    Cerium, neodymium and gadolinium contain double beta active isotopes. The most interesting are 150Nd and 160Gd (promising for 0ν2β search), 136Ce (2β+ candidate with one of the highest Q2β). The main problem of compounds containing lanthanide elements is their high radioactive contamination by uranium, radium, actinium and thorium. The new generation 2β experiments require development of methods for a deep purification of lanthanides from the radioactive elements. A combination of physical and chemical methods was applied to purify cerium, neodymium and gadolinium. Liquid-liquid extraction technique was used to remove traces of Th and U from neodymium, gadolinium and for purification of cerium from Th, U, Ra and K. Co-precipitation and recrystallization methods were utilized for further reduction of the impurities. The radioactive contamination of the samples before and after the purification was tested by using ultra-low-background HPGe gamma spectrometry. As a result of the purification procedure the radioactive contamination of gadolinium oxide (a similar purification efficiency was reached also with cerium and neodymium oxides) was decreased from 0.12 Bq/kg to 0.007 Bq/kg in 228Th, from 0.04 Bq/kg to <0.006 Bq/kg in 226Ra, and from 0.9 Bq/kg to 0.04 Bq/kg in 40K. The purification methods are much less efficient for chemically very similar radioactive elements like actinium, lanthanum and lutetium.

  13. 40 CFR 721.8657 - Cerium, hydroxy oleate propionate complexes.

    Science.gov (United States)

    2010-07-01

    ... complexes. 721.8657 Section 721.8657 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Specific Chemical Substances § 721.8657 Cerium, hydroxy oleate propionate complexes. (a) Chemical substance..., hydroxy oleate propionate complexes (PMN P-99-0026) is subject to reporting under this section for...

  14. Determination of Impurity Elements in Pure Cerium Oxide Product

    Institute of Scientific and Technical Information of China (English)

    Li Peizhong; Chen Limin; Li Jie

    2004-01-01

    Determination of the rare earth impurity in pure cerium oxide is done by ICP-MS.The interference and other factors which affect analytical results were discussed.The accuracy are between 0.81% ~ 11.98% and the recoveries of standard addition are 96% ~ 112.5%.This method can meet the demand for product inspection.

  15. Electrorheological Effects of Cerium-Doped TiO2

    Institute of Scientific and Technical Information of China (English)

    尹剑波; 赵晓鹏

    2001-01-01

    It is found that the doping of cerium ion into anatase TiO2 can improve the electrorheological (ER) effects of TiO2 and broaden the operational temperature range. Especially, the substitution of 7-11 mol% of the cerium dopant for Ti can obtain a relatively high shear stress, t-7.4kPa (at 4kV/mm), which is ten times larger than that of pure TiO2 ER fluid. Also, the typical Ce-doped TiO2 ER fluid shows the highest shear stress at 80℃, but 40℃ for pure TiO2 ER fluid. The dielectric loss and dielectric constant at a low frequency of TiO2 is improved by the doping of cerium, and the temperature dependence of the dielectric properties shows an obvious differnce between pure and doped TiO2 ER fluids. These can well explain the ER behaviour of doped TiO2. Furthermore, the change of rheological and dielectric properties is discussed on the basis of the lattice distortion and defects in TiO2 arising from the doping of cerium.

  16. Purification of cerium, neodymium and gadolinium for low background experiments

    Directory of Open Access Journals (Sweden)

    Boiko R.S.

    2014-01-01

    Full Text Available Cerium, neodymium and gadolinium contain double beta active isotopes. The most interesting are 150Nd and 160Gd (promising for 0ν2β search, 136Ce (2β+ candidate with one of the highest Q2β. The main problem of compounds containing lanthanide elements is their high radioactive contamination by uranium, radium, actinium and thorium. The new generation 2β experiments require development of methods for a deep purification of lanthanides from the radioactive elements. A combination of physical and chemical methods was applied to purify cerium, neodymium and gadolinium. Liquid-liquid extraction technique was used to remove traces of Th and U from neodymium, gadolinium and for purification of cerium from Th, U, Ra and K. Co-precipitation and recrystallization methods were utilized for further reduction of the impurities. The radioactive contamination of the samples before and after the purification was tested by using ultra-low-background HPGe gamma spectrometry. As a result of the purification procedure the radioactive contamination of gadolinium oxide (a similar purification efficiency was reached also with cerium and neodymium oxides was decreased from 0.12 Bq/kg to 0.007 Bq/kg in 228Th, from 0.04 Bq/kg to <0.006 Bq/kg in 226Ra, and from 0.9 Bq/kg to 0.04 Bq/kg in 40K. The purification methods are much less efficient for chemically very similar radioactive elements like actinium, lanthanum and lutetium.

  17. Preparation, Characterization and Antibacterial Property of Cerium Substituted Hydroxyapatite Nanoparticles

    Institute of Scientific and Technical Information of China (English)

    Lin Yingguang; Yang Zhuoru; Cheng Jiang

    2007-01-01

    Nanoparticles of hydroxyapatite (HAP) and cerium substituted hydroxyapatite (CeHAP) with the atomic ratio of Ce/[Ca+Ce] (xCe) from 0 to 0.2 were prepared by sol-gel-supercritical fluid drying (SCFD) method. The nanoparticles were characterized by TEM, XRD, and FT-IR, and the effects of cerium on crystal structure, crystallinity, and particle shape were discussed. With the tests of bacterial inhibition zone and antibacterial ratio, the antibacterial property of HAP and CeHAP nanoparticles on Escherichia coli, Staphylococcus aureus, Lactobacillus were researched. Results showed that the nanoparticles of HAP and CeHAP could be made by sol-gel-SCFD, cerium could partially substitute for calcium and enter the structure of HAP. After substitution, the crystallinity, the IR wavenumbers of bonds in CeHAP decreased gradually with increase of cerium substitution, and the morphology of the nanoparticles changed from the short rod-shaped HAP to the needle-shaped CeHAP. The nanoparticles of HAP and CeHAP with xCe below 0.08 had antibacterial property only forcibly contacting with the test bacteria at the test concentration of 0.1 g·ml-1, however, the CeHAP nanoparticles had antibacterial ability at that concentration no matter statically or dynamically contacting with the test bacteria when xCe was above 0.08, and the antibacterial ability gets better with the increase of xCe, indicating that the antibacterial property was improved after calcium was partially substituted by cerium. The improved antibacterial effects of CeHAP nanoparticle on Lactobacillus showed its potential ability to anticaries.

  18. Cerium as a surrogate in the plutonium immobilization waste form

    Science.gov (United States)

    Marra, James Christopher

    In the aftermath of the Cold War, approximately 50 tonnes (MT) of weapons useable plutonium (Pu) has been identified as excess. The U.S. Department of Energy (DOE) has decided that at least a portion of this material will be immobilized in a titanate-based ceramic for final disposal in a geologic repository. The baseline formulation was designed to produce a ceramic consisting primarily of a highly substituted pyrochlore with minor amounts of brannerite and hafnia-substituted rutile. Since development studies with actual actinide materials is difficult, surrogates have been used to facilitate testing. Cerium has routinely been used as an actinide surrogate in actinide chemistry and processing studies. Although cerium appeared as an adequate physical surrogate for powder handling and general processing studies, cerium was found to act significantly different from a chemical perspective in the Pu ceramic form. The reduction of cerium at elevated temperatures caused different reaction paths toward densification of the respective forms resulting in different phase assemblages and microstructural features. Single-phase fabrication studies and cerium oxidation state analyses were performed to further quantify these behavioral differences. These studies indicated that the major phases in the final phase assemblages contained point defects likely leading to their stability. Additionally, thermochemical arguments predicted that the predominant pyrochlore phase in the ceramic was metastable. The apparent metastabilty associated with primary phase in the Pu ceramic form indicated that additional studies must be performed to evaluate the thermodynamic properties of these compounds. Moreover, the metastability of this predominant phase must be considered in assessment of long-term behavior (e.g. radiation stability) of this ceramic.

  19. [Determination of silver and cerium in the liver and the kidney from a severely burned infant treated with silver sulfadiazine and cerium nitrate].

    Science.gov (United States)

    Hirakawa, K

    1983-02-01

    Silver and cerium in the liver and the kidney from severely burned infant were analyzed by neutron activation method. The patient was treated topically with cerium nitrate/silver sulfadiazine cream and cerium nitrate solution for 3 months. Then, the treatment with these drugs was stopped because of abdominal distention. The patient died 1 month after the cessation of the treatment with these drugs. The tissue specimens, blank liver sample and reference standards were irradiated with TRIGA MARK II Reactor of Rikkyo University. About 1 month after the irradiation, the activities were measured with a Ge(Li) detector coupled to a 4096 channel pulse height analyzer. A large amount of silver was detected both in the liver and in the kidney and a trace of cerium only in the liver. A considerable amount of silver was detected in the liver and its quantity was about 1600 times more than that of normal livers reported by Hamilton, Minski and Cleary (1972-73). Neither silver nor cerium were detected in the blank liver. These results suggest that prolonged topical chemotherapy of cerium nitrate/silver sulfadiazine cream and cerium nitrate solution for the extensive burn injuries causes considerable absorption of silver and cerium into the liver and the kidney. PMID:6867381

  20. 29 CFR 780.126 - Contract arrangements for raising poultry.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 3 2010-07-01 2010-07-01 false Contract arrangements for raising poultry. 780.126 Section... General Scope of Agriculture Raising of Livestock, Bees, Fur-Bearing Animals, Or Poultry § 780.126 Contract arrangements for raising poultry. Feed dealers and processors sometimes enter into...

  1. 7 CFR 1221.126 - Use of information.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 10 2010-01-01 2010-01-01 false Use of information. 1221.126 Section 1221.126 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE SORGHUM PROMOTION, RESEARCH,...

  2. 42 CFR 411.126 - Reopening of determinations and decisions.

    Science.gov (United States)

    2010-10-01

    ... Section 411.126 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES MEDICARE PROGRAM EXCLUSIONS FROM MEDICARE AND LIMITATIONS ON MEDICARE PAYMENT Limitations on Payment for Services Covered Under Group Health Plans: General Provisions § 411.126 Reopening...

  3. 29 CFR 784.126 - Operation of the fishing vessel.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 3 2010-07-01 2010-07-01 false Operation of the fishing vessel. 784.126 Section 784.126... STANDARDS ACT APPLICABLE TO FISHING AND OPERATIONS ON AQUATIC PRODUCTS Exemptions Provisions Relating to Fishing and Aquatic Products General Character and Scope of the Section 13(a)(5) Exemption §...

  4. 7 CFR 959.126 - Handling of culls.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Handling of culls. 959.126 Section 959.126 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements...) Handled for canning or freezing. (b) As a safeguard against culls entering fresh market channels...

  5. Fundamental aspects of regenerative cerium oxide nanoparticles and their applications in nanobiotechnology

    Science.gov (United States)

    Patil, Swanand D.

    Cerium oxide has been used extensively for various applications over the past two decades. The use of cerium oxide nanoparticles is beneficial in present applications and can open avenues for future applications. The present study utilizes the microemulsion technique to synthesize uniformly distributed cerium oxide nanoparticles. The same technique was also used to synthesize cerium oxide nanoparticles doped with trivalent elements (La and Nd). The fundamental study of cerium oxide nanoparticles identified variations in properties as a function of particle size and also due to doping with trivalent elements (La and Nd). It was found that the lattice parameter of cerium oxide nanoparticles increases with decrease in particle size. Also Raman allowed mode shift to lower energies and the peak at 464 cm-1 becomes broader and asymmetric. The size dependent changes in cerium oxide were correlated to increase in oxygen vacancy concentration in the cerium oxide lattice. The doping of cerium oxide nanoparticles with trivalent elements introduces more oxygen vacancies and expands the cerium oxide lattice further (in addition to the lattice expansion due to the size effect). The lattice expansion is greater for La-doped cerium oxide nanoparticles compared to Nd-doping due to the larger ionic radius of La compared to Nd, the lattice expansion is directly proportional to the dopant concentration. The synthesized cerium oxide nanoparticles were used to develop an electrochemical biosensor of hydrogen peroxide (H2O2). The sensor was useful to detect H2O2 concentrations as low as 1muM in water. Also the preliminary testing of the sensor on tomato stem and leaf extracts indicated that the sensor can be used in practical applications such as plant physiological studies etc. The nanomolar concentrations of cerium oxide nanoparticles were also found to be useful in decreasing ROS (reactive oxygen species) mediated cellular damages in various in vitro cell cultures. Cerium oxide

  6. Effect of cerium modification on microstructure and properties of hypereutectic high chromium cast iron

    Energy Technology Data Exchange (ETDEWEB)

    Zhi, Xiaohui, E-mail: mkmkzxh@hotmail.com [School of Mechanical Engineering, Shijiazhuang Tiedao University, Shijiazhuang 050043, Hebei Province (China); Liu, Jinzhi [School of Mechanical Engineering, Shijiazhuang Tiedao University, Shijiazhuang 050043, Hebei Province (China); Xing, Jiandong; Ma, Shengqiang [State Key Laboratory Mechanical Behavior of Materials, School of Materials Science and Engineering, Xi' an Jiaotong University, Xi' an 710049, Shaanxi Province (China)

    2014-05-01

    The effect of cerium modification on the microstructure and properties of hypereutectic high chromium cast iron primarily containing 4.0 wt% C and 20.0 wt% Cr was studied by means of optical microscopy, transmission electron microscope, scanning electron microscope, and energy dispersive X-ray spectrometry. The primary M{sub 7}C{sub 3} carbides were refined obviously when cerium was added in the melt. Ce{sub 2}S{sub 3} was found in the primary M{sub 7}C{sub 3} carbides and acted as the heterogeneous substrate of M{sub 7}C{sub 3} carbides. The impact toughness of the specimen modified with 0.5 wt% cerium increased by 50% compared with the specimen without cerium modification. The hardness of the alloy modified with cerium increased slightly compared with the specimen without cerium modification.

  7. Synthesis and crystal kinetics of cerium oxide nanocrystallites prepared by co-precipitation process

    Energy Technology Data Exchange (ETDEWEB)

    Shih, C.J., E-mail: cjshih@kmu.edu.tw [Department of Fragrance and Cosmetics Science, Kaohsiung Medical University, 100 Shi-Chuan 1st Road, Kaohsiung 807, Taiwan (China); Chen, Y.J. [Institute of Biomedical Sciences, National Sun Yat-Sen University, Kaohsiung 804, Taiwan (China); Hon, M.H. [Department of Materials Science and Engineering, National Cheng Kung University, Tainan 701, Taiwan (China)

    2010-05-15

    Cerium oxide nanocrystallites were synthesized at a relatively low temperature using cerium nitrate as starting materials in a water solution by a co-precipitation process. Effect of calcination temperature on the crystallite growth of cerium oxide nano-powders was investigated by X-ray diffraction, transmission electron microscopy and electron diffraction. The crystallization temperature of the cerium oxide powders was estimated to be about 273 K by XRD analysis. When calcined from 473 to 1273 K, the crystallization of the face-centered cubic phase was observed by XRD. The crystallite size of the cerium oxide increased from 10.0 to 43.8 nm with calcining temperature increasing from 673 to 1273 K. The activation energy for growth of cerium oxide nanoparticles was found to be 16.0 kJ mol{sup -1}.

  8. Synthesis and crystal kinetics of cerium oxide nanocrystallites prepared by co-precipitation process

    International Nuclear Information System (INIS)

    Cerium oxide nanocrystallites were synthesized at a relatively low temperature using cerium nitrate as starting materials in a water solution by a co-precipitation process. Effect of calcination temperature on the crystallite growth of cerium oxide nano-powders was investigated by X-ray diffraction, transmission electron microscopy and electron diffraction. The crystallization temperature of the cerium oxide powders was estimated to be about 273 K by XRD analysis. When calcined from 473 to 1273 K, the crystallization of the face-centered cubic phase was observed by XRD. The crystallite size of the cerium oxide increased from 10.0 to 43.8 nm with calcining temperature increasing from 673 to 1273 K. The activation energy for growth of cerium oxide nanoparticles was found to be 16.0 kJ mol-1.

  9. Solubility of cerium in LaCoO3-influence on catalytic activity.

    Science.gov (United States)

    French, S A; Catlow, C R A; Oldman, R J; Rogers, S C; Axon, S A

    2002-11-21

    The recent interest in the catalytic properties of lanthanum perovskites for methane combustion and three way catalysis has led to considerable debate as to their structure and defect chemistry. We have investigated the doping of LaCoO3 with the tetravalent cerium cation using atomistic simulation techniques. We have compared three routes for cerium insertion and identified the favoured doping mechanism, which explain experimental observations relating to the effect of cerium on catalytic activity.

  10. Critical indices for reversible gamma-alpha phase transformation in metallic cerium

    Science.gov (United States)

    Soldatova, E. D.; Tkachenko, T. B.

    1980-08-01

    Critical indices for cerium have been determined within the framework of the pseudobinary solution theory along the phase equilibrium curve, the critical isotherm, and the critical isobar. The results obtained verify the validity of relationships proposed by Rushbrook (1963), Griffiths (1965), and Coopersmith (1968). It is concluded that reversible gamma-alpha transformation in metallic cerium is a critical-type transformation, and cerium has a critical point on the phase diagram similar to the critical point of the liquid-vapor system.

  11. The effect of cerium valence states at cerium oxide nanoparticle surfaces on cell proliferation

    KAUST Repository

    Naganuma, Tamaki

    2014-05-01

    Understanding and controlling cell proliferation on biomaterial surfaces is critical for scaffold/artificial-niche design in tissue engineering. The mechanism by which underlying integrin ligates with functionalized biomaterials to induce cell proliferation is still not completely understood. In this study, poly-l-lactide (PL) scaffold surfaces were functionalized using layers of cerium oxide nanoparticles (CNPs), which have recently attracted attention for use in therapeutic application due to their catalytic ability of Ce4+ and Ce3+ sites. To isolate the influence of Ce valance states of CNPs on cell proliferation, human mesenchymal stem cells (hMSCs) and osteoblast-like cells (MG63) were cultured on the PL/CNP surfaces with dominant Ce4+ and Ce3+ regions. Despite cell type (hMSCs and MG63 cells), different surface features of Ce4+ and Ce3+ regions clearly promoted and inhibited cell spreading, migration and adhesion behavior, resulting in rapid and slow cell proliferation, respectively. Cell proliferation results of various modified CNPs with different surface charge and hydrophobicity/hydrophilicity, indicate that Ce valence states closely correlated with the specific cell morphologies and cell-material interactions that trigger cell proliferation. This finding suggests that the cell-material interactions, which influence cell proliferation, may be controlled by introduction of metal elements with different valence states onto the biomaterial surface. © 2014 Elsevier Ltd.

  12. Study of cerium diffusion in undoped lithium-6 enriched glass with Rutherford backscattering spectrometry

    Science.gov (United States)

    Zhang, Xiaodong; Moore, Michael E.; Lee, Kyung-Min; Lukosi, Eric D.; Hayward, Jason P.

    2016-07-01

    Undoped lithium-6 enriched glasses coated with pure cerium (99.9%) with a gold protection layer on top were heated at three different temperatures (500, 550, and 600 °C) for varied durations (1, 2, and 4 h). Diffusion profiles of cerium in such glasses were obtained with the conventional Rutherford backscattering technique. Through fitting the diffusion profiles with the thin-film solution of Fick's second law, diffusion coefficients of cerium with different annealing temperatures and durations were solved. Then, the activation energy of cerium for the diffusion process in the studied glasses was found to be 114 kJ/mol with the Arrhenius equation.

  13. Adsorption of Fluoride Ion by Inorganic Cerium Based Adsorbent

    Institute of Scientific and Technical Information of China (English)

    Jiao Zhongzhi(焦中志); Chen Zhonglin; Yang Min; Zhang Yu; Li Guibai

    2004-01-01

    Excess of fluoride in drinking water is harmful to human health, the concentration of F- ions must be maintained in the range of 0.5 to 1.5 mg/L. An inorganic cerium based adsorbent (CTA) is developed on the basis of research of adsorption of fluoride on cerium oxide hydrate. Some adsorption of fluoride by CTA adsorbent experiments were carried out, and results showed that CTA adsorbent has a quick adsorption speed and a large adsorption capacity. Adsorption follows Freundlich isotherm, and low pH value helps fluoride removal. Some physical-chemical characteristics of CTA adsorbent were experimented, fluoride removal mechanism was explored, and results showed that hydroxyl group of CTA adsorbent played an important role in the fluoride removal.

  14. Antioxidant activity of levan coated cerium oxide nanoparticles.

    Science.gov (United States)

    Kim, Sun-Jung; Chung, Bong Hyun

    2016-10-01

    Levan coated cerium oxide nanoparticles (LCNPs) with the enhanced antioxidant activity were successfully synthesized and characterized. Levan and their derivatives are attractive for biomedical applications attributable to their antioxidant, anti-inflammation and anti-tumor properties. LCNPs were synthesized using the one-pot and green synthesis system with levan. For production of nanoparticles, levan plays a role as a stabilizing and reducing agent. Fourier transform infrared spectroscopy (FT-IR) analysis showed that LCNPs successfully synthesized. The morphology and size of nanoparticles were confirmed by transmission electron microscopy (TEM) and dynamic light scattering (DLS). LCNPs have good water solubility and stability. The conjugation of levan with cerium oxide nanoparticles improved antioxidant activity. Moreover the level of ROS was reduced after treatment of LCNPs to H2O2 stimulated NIH3T3 cells. These results demonstrate that the LCNPs are useful for applying of treatment of ROS induced diseases. PMID:27312651

  15. Synthesis and characterization of cerium sulfide thin film

    Institute of Scientific and Technical Information of China (English)

    Ιshak Afsin Kariper

    2014-01-01

    Cerium sulfide (CexSy) polycrystalline thin film is coated with chemical bath deposition on substrates (commercial glass). Transmittance, absorption, optical band gap and refractive index are examined by using UV/VIS. Spectrum. The hexagonal form is observed in the structural properties in XRD. The structural and optical properties of cerium sulfide thin films are analyzed at different pH. SEM and EDX analyses are made for surface analysis and elemental ratio in films. It is observed that some properties of films changed with different pH values. In this study, the focus is on the observed changes in the properties of films. The pH values were scanned at 6–10. The optical band gap changed with pH between 3.40 to 3.60 eV. In addition, the film thickness changed with pH at 411 nm to 880 nm.

  16. Far infrared properties of PbTe doped with cerium

    Energy Technology Data Exchange (ETDEWEB)

    Nikolic, P.M. [Institute of Technical Sciences SASA, Knez Mihailova 35/IV, 11000 Belgrade (Serbia)]. E-mail: nikolic@sanu.ac.yu; Koenig, W. [Max Planck Institut fuer Festkoerperforschung, Heisenbergstrasse 1, 7000 Stuttgart 80 (Germany); Vujatovic, S.S. [Institute of Technical Sciences SASA, Knez Mihailova 35/IV, 11000 Belgrade (Serbia); Blagojevic, V. [Faculty of Electronic Engineering, University of Belgrade, Bulevar Kralja Aleksandra 73, 11000 Belgrade (Serbia); Lukovic, D. [Institute of Technical Sciences SASA, Knez Mihailova 35/IV, 11000 Belgrade (Serbia); Savic, S. [Institute of Technical Sciences SASA, Knez Mihailova 35/IV, 11000 Belgrade (Serbia); Radulovic, K. [Institute of Technical Sciences SASA, Knez Mihailova 35/IV, 11000 Belgrade (Serbia); Urosevic, D. [Mathematical Institute SASA, Knez Mihailova 35/I, 11000 Belgrade (Serbia); Nikolic, M.V. [Center for Multidisciplinary Studies of the University of Belgrade, Kneza Viseslava 1, Belgrade (Serbia)

    2007-05-16

    Single crystal samples of lead telluride doped with cerium were made using the Bridgman method. Far infrared reflectivity spectra in the temperature range from 10 to 300 K are presented. The experimental data were numerically analyzed using a fitting procedure based on the plasmon-phonon interaction model and optical parameters were determined. Two additional local modes were observed at about 138 and 337 cm{sup -1}. The origin of these local vibrational impurity modes was discussed.

  17. Monomers, Dimers, and Helices: Complexities of Cerium and Plutonium Phenanthrolinecarboxylates.

    Science.gov (United States)

    Cary, Samantha K; Ferrier, Maryline G; Baumbach, Ryan E; Silver, Mark A; Lezama Pacheco, Juan; Kozimor, Stosh A; La Pierre, Henry S; Stein, Benjamin W; Arico, Alexandra A; Gray, Danielle L; Albrecht-Schmitt, Thomas E

    2016-05-01

    The reaction of Ce(III) or Pu(III) with 1,10-phenanthroline-2,9-dicarboxylic acid (PDAH2) results in the formation of new f-element coordination complexes. In the case of cerium, Ce(PDA)(H2O)2Cl·H2O (1) or [Ce(PDAH)(PDA)]2[Ce(PDAH)(PDA)] (2) was isolated depending on the Ce/ligand ratio in the reaction. The structure of 2 is composed of two distinct substructures that are constructed from the same monomer. This monomer is composed of a Ce(III) cation bound by one PDA(2-) dianionic ligand and one PDAH(-) monoanionic ligand, both of which are tetradentate. Bridging by the carboxylate moieties leads to either [Ce(PDAH)(PDA)]2 dimers or [Ce(PDAH)(PDA)]1∞ helical chains. For plutonium, Pu(PDA)2 (3) was the only product isolated regardless of the Pu/ligand ratio employed in the reaction. During the reaction of plutonium with PDAH2, Pu(III) is oxidized to Pu(IV), generating 3. This assignment is consistent with structural metrics and the optical absorption spectrum. Ambiguity in the assignment of the oxidation state of cerium in 1 and 2 from UV-vis-near-IR spectra invoked the use of Ce L3,2-edge X-ray absorption near-edge spectroscopy, magnetic susceptibility, and heat capacity measurements. These experiments support the assignment of Ce(III) in both compounds. The bond distances and coordination numbers are also consistent with these assignments. 3 contains 8-coordinate Pu(IV), whereas the cerium centers in 1 and 2 are 9- and/or 10-coordinate, which correlates with the increased size of Ce(III) versus Pu(IV). Taken together, these data provide an example of a system where the differences in the redox behavior between these f elements creates more complex chemistry with cerium than with plutonium. PMID:27070401

  18. Jet formation in cerium metal to examine material strength

    Energy Technology Data Exchange (ETDEWEB)

    Jensen, B. J., E-mail: bjjensen@lanl.gov; Cherne, F. J.; Prime, M. B.; Yeager, J. D.; Ramos, K. J.; Hooks, D. E.; Cooley, J. C.; Dimonte, G. [Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); Fezzaa, K. [Argonne National Laboratory, Argonne, Illinois 60439 (United States); Iverson, A. J.; Carlson, C. A. [National Security Technologies LLC, Los Alamos, New Mexico 87544 (United States)

    2015-11-21

    Examining the evolution of material properties at extreme conditions advances our understanding of numerous high-pressure phenomena from natural events like meteorite impacts to general solid mechanics and fluid flow behavior. Recent advances in synchrotron diagnostics coupled with dynamic compression platforms have introduced new possibilities for examining in-situ, spatially resolved material response with nanosecond time resolution. In this work, we examined jet formation from a Richtmyer-Meshkov instability in cerium initially shocked into a transient, high-pressure phase, and then released to a low-pressure, higher-temperature state. Cerium's rich phase diagram allows us to study the yield stress following a shock induced solid-solid phase transition. X-ray imaging was used to obtain images of jet formation and evolution with 2–3 μm spatial resolution. From these images, an analytic method was used to estimate the post-shock yield stress, and these results were compared to continuum calculations that incorporated an experimentally validated equation-of-state (EOS) for cerium coupled with a deviatoric strength model. Reasonable agreement was observed between the calculations and the data illustrating the sensitivity of jet formation on the yield stress values. The data and analysis shown here provide insight into material strength during dynamic loading which is expected to aid in the development of strength aware multi-phase EOS required to predict the response of matter at extreme conditions.

  19. Enhancing cerium and plutonium solubility by reduction in borosilicate glass

    Science.gov (United States)

    Cachia, J.-N.; Deschanels, X.; Den Auwer, C.; Pinet, O.; Phalippou, J.; Hennig, C.; Scheinost, A.

    2006-06-01

    High-level radioactive wastes produced by spent fuel reprocessing containing fission and activation products as well as actinides are incorporated in a borosilicate glass. To ensure optimum radionuclide containment, the resulting glass must be as homogeneous as possible. Microscopic heterogeneity can arise from various processes including the excess loading of an element above its solubility limit. The current actinide loading limit is 0.4 wt%. Work is in progress to assess the actinide solubility in these glasses, especially for plutonium. Initially the actinides were simulated by lanthanides and hafnium. The results show that trivalent elements (La, Gd) exhibit greater solubility than tetravalent elements (Pu, Hf). Cerium is an interesting element because its oxidation state varies from IV to III depending on the process conditions, such as the temperature and redox potential of the melt. In order to quantify the solubility increase, cerium-doped glass samples were melted under reducing conditions by adding a reducing agent. The solubility observed at 1473 K increased significantly from 0.95 to 13.00 wt%. Several reducing compounds have been tested. This paper deals with this study and the application to reduce Pu(IV) to Pu(III). The reduction state was characterized by X-ray absorption spectroscopy (XANES) for plutonium and by chemical analysis for cerium. The material homogeneity was verified by optical and scanning electron microscopy. Preliminary findings concerning the reduction of Pu-doped glasses fabricated in hot cells are also discussed.

  20. The developments and challenges of cerium half-cell in zinc–cerium redox flow battery for energy storage

    International Nuclear Information System (INIS)

    Zinc–cerium redox flow batteries (ZCBs) are emerging as a very promising new technology with the potential to store a large amount of energy economically and efficiently, thanking to its highest thermodynamic open-circuit cell voltage among all the currently studied aqueous redox flow batteries. However, there are numerous scientific and technical challenges that must be overcome if this alluring promise is to turn into reality, from designing the battery structure, to optimizing the electrolyte compositions and elucidating the complex chemical reactions that occur during charge and discharge. This review article is the first summary of the most significant developments and challenges of cerium half-cell and the current understanding of their chemistry. We are certain that this review will be of great interest to audience over a broad range, especially in fields of energy storage, electrochemistry, and chemical engineering

  1. High-Spin Level Scheme of 126Cs%126Cs的高自旋态能级结构

    Institute of Scientific and Technical Information of China (English)

    王守宇; Y.Iwata; T.Morikawa; G.B.Hagcmann; G.Sletten; J.Nyberg; D.Jerrestam; H.J.Jensen; J.Espino; J.Gascon; N.GjφJrnp; 马英君; B.Cederwall; P.O.TjφJm; T.Komatsubara; 刘运祚; 张玉虎; 梁国栋; K.Furuno; T.Hayakawa; J.Mukai

    2004-01-01

    利用融合蒸发反应 116Cd(14N,4n) 126Cs布居了 126Cs的高自旋态.观测到了100多条新的γ跃迁和相应的能级,建立了双奇核 126Cs由9个转动带构成的能级纲图.尝试性地指定了大部分能级的自旋和宇称以及各转动带的Nilsson单粒子组态.极大地丰富了已有的实验结果.

  2. Cluster (Cyanobacteria): 1158:126 [PGDBj - Ortholog DB

    Lifescience Database Archive (English)

    Full Text Available 1158:126 ATPase family protein associated with various cellular activities (AAA),AT...Pase family protein associated with various cellular activities (AAA) 1150:1376 118323:547|118323:546|482564:2199|272129:938 ...

  3. 1.26 Single Frequency Fiber Laser Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This proposal is for the development of an innovative compact, high power, and extremely reliable 1.26 micron Ho-doped single frequency fiber laser. The proposed...

  4. 40 CFR Appendix A to Part 423 - 126 Priority Pollutants

    Science.gov (United States)

    2010-07-01

    ... STANDARDS STEAM ELECTRIC POWER GENERATING POINT SOURCE CATEGORY Pt. 423, App. A Appendix A to Part 423—126...-bromophenyl phenyl ether 042Bis(2-chloroisopropyl) ether 043Bis(2-chloroethoxy) methane 044Methylene...

  5. Induction of pulmonary fibrosis by cerium oxide nanoparticles

    International Nuclear Information System (INIS)

    Cerium compounds have been used as a diesel engine catalyst to lower the mass of diesel exhaust particles, but are emitted as cerium oxide (CeO2) nanoparticles in the diesel exhaust. In a previous study, we have demonstrated a wide range of CeO2-induced lung responses including sustained pulmonary inflammation and cellular signaling that could lead to pulmonary fibrosis. In this study, we investigated the fibrogenic responses induced by CeO2 in a rat model at various time points up to 84 days post-exposure. Male Sprague Dawley rats were exposed to CeO2 by a single intratracheal instillation. Alveolar macrophages (AM) were isolated by bronchial alveolar lavage (BAL). AM-mediated cellular responses, osteopontin (OPN) and transform growth factor (TGF)-β1 in the fibrotic process were investigated. The results showed that CeO2 exposure significantly increased fibrotic cytokine TGF-β1 and OPN production by AM above controls. The collagen degradation enzymes, matrix metalloproteinase (MMP)-2 and -9 and the tissue inhibitor of MMP were markedly increased in the BAL fluid at 1 day- and subsequently declined at 28 days after exposure, but remained much higher than the controls. CeO2 induced elevated phospholipids in BAL fluid and increased hydroxyproline content in lung tissue in a dose- and time-dependent manner. Immunohistochemical analysis showed MMP-2, MMP-9 and MMP-10 expressions in fibrotic regions. Morphological analysis noted increased collagen fibers in the lungs exposed to a single dose of 3.5 mg/kg CeO2 and euthanized at 28 days post-exposure. Collectively, our studies show that CeO2 induced fibrotic lung injury in rats, suggesting it may cause potential health effects. -- Highlights: ► Cerium oxide exposure significantly affected the following parameters in the lung. ► Induced fibrotic cytokine OPN and TGF-β1 production and phospholipidosis. ► Caused imbalance of the MMP-9/ TIMP-1 ratio that favors fibrosis. ► Cerium oxide particles were detected in

  6. Induction of pulmonary fibrosis by cerium oxide nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Jane Y., E-mail: jym1@cdc.gov [Health Effects Laboratory Division, National Institute for Occupational Safety and Health, Morgantown, WV 26505 (United States); Mercer, Robert R.; Barger, Mark; Schwegler-Berry, Diane; Scabilloni, James [Health Effects Laboratory Division, National Institute for Occupational Safety and Health, Morgantown, WV 26505 (United States); Ma, Joseph K. [School of Pharmacy, West Virginia University, Morgantown, WV 26506 (United States); Castranova, Vincent [Health Effects Laboratory Division, National Institute for Occupational Safety and Health, Morgantown, WV 26505 (United States)

    2012-08-01

    Cerium compounds have been used as a diesel engine catalyst to lower the mass of diesel exhaust particles, but are emitted as cerium oxide (CeO{sub 2}) nanoparticles in the diesel exhaust. In a previous study, we have demonstrated a wide range of CeO{sub 2}-induced lung responses including sustained pulmonary inflammation and cellular signaling that could lead to pulmonary fibrosis. In this study, we investigated the fibrogenic responses induced by CeO{sub 2} in a rat model at various time points up to 84 days post-exposure. Male Sprague Dawley rats were exposed to CeO{sub 2} by a single intratracheal instillation. Alveolar macrophages (AM) were isolated by bronchial alveolar lavage (BAL). AM-mediated cellular responses, osteopontin (OPN) and transform growth factor (TGF)-β1 in the fibrotic process were investigated. The results showed that CeO{sub 2} exposure significantly increased fibrotic cytokine TGF-β1 and OPN production by AM above controls. The collagen degradation enzymes, matrix metalloproteinase (MMP)-2 and -9 and the tissue inhibitor of MMP were markedly increased in the BAL fluid at 1 day- and subsequently declined at 28 days after exposure, but remained much higher than the controls. CeO{sub 2} induced elevated phospholipids in BAL fluid and increased hydroxyproline content in lung tissue in a dose- and time-dependent manner. Immunohistochemical analysis showed MMP-2, MMP-9 and MMP-10 expressions in fibrotic regions. Morphological analysis noted increased collagen fibers in the lungs exposed to a single dose of 3.5 mg/kg CeO{sub 2} and euthanized at 28 days post-exposure. Collectively, our studies show that CeO{sub 2} induced fibrotic lung injury in rats, suggesting it may cause potential health effects. -- Highlights: ► Cerium oxide exposure significantly affected the following parameters in the lung. ► Induced fibrotic cytokine OPN and TGF-β1 production and phospholipidosis. ► Caused imbalance of the MMP-9/ TIMP-1 ratio that favors fibrosis

  7. Cerium doped red mud catalytic ozonation for bezafibrate degradation in wastewater: Efficiency, intermediates, and toxicity.

    Science.gov (United States)

    Xu, Bingbing; Qi, Fei; Sun, Dezhi; Chen, Zhonglin; Robert, Didier

    2016-03-01

    In this study, the performance of bezafibrate (BZF) degradation and detoxification in the aqueous phase using cerium-modified red mud (RM) catalysts prepared using different cerium sources and synthesis methods were evaluated. Experimental results showed that the surface cerium modification was responsible for the development of the catalytic activity of RM and this was influenced by the cerium source and the synthesis method. Catalyst prepared from cerium (IV) by precipitation was found to show the best catalytic activity in BZF degradation and detoxification. Reactive oxygen species including peroxides, hydroxyl radicals, and super oxide ions were identified in all reactions and we proposed the corresponding catalytic reaction mechanism for each catalyst that prepared from different cerium source and method. This was supported by the intermediates profiles that were generated upon BZF degradation. The surface and the structural properties of cerium-modified RM were characterized in detail by several analytical methods. Two interesting findings were made: (1) the surface texture (specific surface area and mesoporous volume) influenced the catalytic reaction pathway; and (2) Ce(III) species and oxygen vacancies were generated on the surface of the catalyst after cerium modification. This plays an important role in the development of the catalytic activity. PMID:26706928

  8. Tuning Reactivity and Electronic Properties through Ligand Reorganization within a Cerium Heterobimetallic Framework

    Energy Technology Data Exchange (ETDEWEB)

    Robinson, Jerome R.; Gordon, Zachary; Booth, Corwin H.; Carroll, Patrick J.; Walsh, Patrick J.; Schelter, Eric J.

    2014-06-24

    Cerium compounds have played vital roles in organic, inorganic, and materials chemistry due to their reversible redox chemistry between trivalent and tetravalent oxidation states. However, attempts to rationally access molecular cerium complexes in both oxidation states have been frustrated by unpredictable reactivity in cerium(III) oxidation chemistry. Such oxidation reactions are limited by steric saturation at the metal ion, which can result in high energy activation barriers for electron transfer. An alternative approach has been realized using a rare earth/alkali metal/1,1'-BINOLate (REMB) heterobimetallic framework, which uses redox-inactive metals within the secondary coordination sphere to control ligand reorganization. The rational syntheses of functionalized cerium(IV) products and a mechanistic examination of the role of ligand reorganization in cerium(III) oxidation are presented.

  9. The recrystallization and texture of magnesium-zinc-cerium alloys

    Energy Technology Data Exchange (ETDEWEB)

    Mackenzie, L.W.F. [Novelis Global Technology Centre, 945 Princess Street, Kingston, Ontario, K7L 5L9 (Canada); Department of Mining and Materials Engineering, McGill University, 3610 University, Montreal, Quebec, H3A 2B2 (Canada)], E-mail: luke.mackenzie@novelis.com; Pekguleryuz, M.O. [Department of Mining and Materials Engineering, McGill University, 3610 University, Montreal, Quebec, H3A 2B2 (Canada)

    2008-09-15

    Optical microscopy, electron backscatter diffraction and X-ray diffraction are employed to characterize the microstructures and textures of as-rolled and annealed Mg-1Zn and Mg-1Zn-xCe. Mg-1Zn exhibited 'basal' textures: the basal poles aligned with the sheet normal direction. With the addition of cerium, the texture was basal when recrystallization was limited; during recrystallization, the basal texture component weakened, to be replaced by a component with basal poles rotated {approx}45 deg. towards the transverse direction. Deformation, recrystallization and texture are discussed.

  10. The recrystallization and texture of magnesium-zinc-cerium alloys

    International Nuclear Information System (INIS)

    Optical microscopy, electron backscatter diffraction and X-ray diffraction are employed to characterize the microstructures and textures of as-rolled and annealed Mg-1Zn and Mg-1Zn-xCe. Mg-1Zn exhibited 'basal' textures: the basal poles aligned with the sheet normal direction. With the addition of cerium, the texture was basal when recrystallization was limited; during recrystallization, the basal texture component weakened, to be replaced by a component with basal poles rotated ∼45 deg. towards the transverse direction. Deformation, recrystallization and texture are discussed

  11. Electrochemical studies on cerium(Ⅲ) in molten fluoride mixtures

    Institute of Scientific and Technical Information of China (English)

    VIRGIL; CONSTANTIN; ANA-MARIA; POPESCU; MIRCEA; OLTEANU

    2010-01-01

    This study aims to determine the principal electrochemical characteristics of the electrodeposition of cerium metal from molten fluoride systems.The cathodic process of Ce3+ ions in LiF-NaF and LiF-NaF-CaF2 molten salts was studied using electrochemical techniques as steady state and cyclic voltammetry methods.The decomposition potential(Ed) and the overvoltage(η) were determined for NaCeF4 using current-potential curves under galvanostatic conditions.The Ed was found to be 2.025 V in LiF-NaF and 2.045 V in...

  12. Options for the recovery of cerium by solvent extraction

    Energy Technology Data Exchange (ETDEWEB)

    Soldenhoff, K.H. [Australian Nuclear Science and Technology Organisation, Lucas Heights, NSW (Australia)

    1996-12-31

    This paper reports the results of an experimental program to examine the use of various commercial reagents for the extraction of cerium (IV) from sulphate solutions. Extractants tested include organophosphorus esters (TOPO, Cyanex 923 and Cyanex 925), organophosphorus acids (DEHPA, lonquest 801 and Cyanex 272) and high molecular weight amine, Alamine 336. The suitability of reagents is assessed in terms of process relevant criteria such as extraction dependence on acidity, selectivity over other rare earths and thorium, stability of reagent towards oxidation and loading characteristics. (author) 15 refs., 2 tabs., 5 figs.

  13. Properties of hot liquid cerium by LDA + U molecular dynamics.

    Science.gov (United States)

    Siberchicot, Bruno; Clérouin, Jean

    2012-11-14

    We present ab initio simulations of liquid cerium in the framework of the LDA + U formulation. The liquid density has been determined self-consistently by searching for the zero pressure equilibrium state at 1320 K with the same set of parameters (U and J) and occupation matrices as those optimized for the γ phase. We have computed static and transport properties. The liquid produced by the simulations appears more structured than the available measurements. This raises questions regarding the ability of the theory to describe such a complex liquid. Conductivity calculations and temperature dependences are nevertheless in reasonable agreement with data.

  14. Soil organic matter influences cerium translocation and physiological processes in kidney bean plants exposed to cerium oxide nanoparticles.

    Science.gov (United States)

    Majumdar, Sanghamitra; Peralta-Videa, Jose R; Trujillo-Reyes, Jesica; Sun, Youping; Barrios, Ana C; Niu, Genhua; Margez, Juan P Flores-; Gardea-Torresdey, Jorge L

    2016-11-01

    Soil organic matter plays a major role in determining the fate of the engineered nanomaterials (ENMs) in the soil matrix and effects on the residing plants. In this study, kidney bean plants were grown in soils varying in organic matter content and amended with 0-500mg/kg cerium oxide nanoparticles (nano-CeO2) under greenhouse condition. After 52days of exposure, cerium accumulation in tissues, plant growth and physiological parameters including photosynthetic pigments (chlorophylls and carotenoids), net photosynthesis rate, transpiration rate, and stomatal conductance were recorded. Additionally, catalase and ascorbate peroxidase activities were measured to evaluate oxidative stress in the tissues. The translocation factor of cerium in the nano-CeO2 exposed plants grown in organic matter enriched soil (OMES) was twice as the plants grown in low organic matter soil (LOMS). Although the leaf cover area increased by 65-111% with increasing nano-CeO2 concentration in LOMS, the effect on the physiological processes were inconsequential. In OMES leaves, exposure to 62.5-250mg/kg nano-CeO2 led to an enhancement in the transpiration rate and stomatal conductance, but to a simultaneous decrease in carotenoid contents by 25-28%. Chlorophyll a in the OMES leaves also decreased by 27 and 18% on exposure to 125 and 250mg/kg nano-CeO2. In addition, catalase activity increased in LOMS stems, and ascorbate peroxidase increased in OMES leaves of nano-CeO2 exposed plants, with respect to control. Thus, this study provides clear evidence that the properties of the complex soil matrix play decisive roles in determining the fate, bioavailability, and biological transport of ENMs in the environment. PMID:27343939

  15. Characterization of microstructure and catalytic of cerium oxide obtained by colloidal solution

    International Nuclear Information System (INIS)

    This study investigated to obtain particles of cerium oxide, for use as catalysts for the combustion of methane using the technique of through polymeric colloidal solution. Obtaining the colloidal system is based on hydrolysis of salts such as cerium acetylacetonate, cerium nitrate in the presence of additives such as polyvinylbutyral (PVB), polyvinylpyrrolidone (PVP) and polyvinyl acetate (PVA), at concentrations of 5, 10 and 15% in aqueous or alcoholic medium. These solutions containing ions of interest were subjected to a heat treatment at 650° C for 30 minutes, with heating rate of 2 ° C/ min. After heat treatment, the fibers were characterized according to their morphology, surface area, crystallinity, weight loss and catalytic activity. Samples obtained from cerium acetylacetonate were more reactive than the cerium nitrate to the combustion of methane, as showed greater conversions and higher temperatures reached during the process, which is of utmost importance since the combustion catalytic methane is used for generating thermal energy. After the reaction with methane, the samples underwent significant change in surface area, probably due to the intensity of combustion reactions of the nitrate and the generation of heat involved in this reaction, which gave rise to coarse particles. During the combustion process using the obtained from particles of cerium acetylacetonate, there was the release of large quantities of nitrogen compared to the results of assays with the particles obtained with cerium nitrate. (author)

  16. 40 CFR Appendix C to Part 97 - Final Section 126 Rule: Trading Budget

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Final Section 126 Rule: Trading Budget... PROGRAMS (CONTINUED) FEDERAL NOX BUDGET TRADING PROGRAM AND CAIR NOX AND SO2 TRADING PROGRAMS Pt. 97, App. C Appendix C to Part 97—Final Section 126 Rule: Trading Budget ST F126-EGU F126-NEGU Total DC 207...

  17. Cerium fluoride nanoparticles protect cells against oxidative stress

    Energy Technology Data Exchange (ETDEWEB)

    Shcherbakov, Alexander B.; Zholobak, Nadezhda M. [Zabolotny Institute of Microbiology and Virology, National Academy of Sciences of Ukraine, Kyiv D0368 (Ukraine); Baranchikov, Alexander E. [Kurnakov Institute of General and Inorganic Chemistry of the Russian Academy of Sciences, Moscow 119991 (Russian Federation); Ryabova, Anastasia V. [Prokhorov General Physics Institute of the Russian Academy of Sciences, Moscow 119991 (Russian Federation); National Research Nuclear University MEPhI (Moscow Engineering Physics Institute), Moscow 115409 (Russian Federation); Ivanov, Vladimir K., E-mail: van@igic.ras.ru [Kurnakov Institute of General and Inorganic Chemistry of the Russian Academy of Sciences, Moscow 119991 (Russian Federation); National Research Tomsk State University, Tomsk 634050 (Russian Federation)

    2015-05-01

    A novel facile method of non-doped and fluorescent terbium-doped cerium fluoride stable aqueous sols synthesis is proposed. Intense green luminescence of CeF{sub 3}:Tb nanoparticles can be used to visualize these nanoparticles' accumulation in cells using confocal laser scanning microscopy. Cerium fluoride nanoparticles are shown for the first time to protect both organic molecules and living cells from the oxidative action of hydrogen peroxide. Both non-doped and terbium-doped CeF{sub 3} nanoparticles are shown to provide noteworthy protection to cells against the vesicular stomatitis virus. - Highlights: • Facile method of CeF{sub 3} and CeF{sub 3}:Tb stable aqueous sols synthesis is proposed. • Naked CeF{sub 3} nanoparticles are shown to be non-toxic and to protect cells from the action of H{sub 2}O{sub 2}. • CeF{sub 3} and CeF{sub 3}:Tb nanoparticles are shown to protect living cells against the vesicular stomatitis virus.

  18. New sunscreen materials based on amorphous cerium and titanium phosphate

    International Nuclear Information System (INIS)

    Cerium-titanium pyrophosphates Ce1-xTi xP2O7 (with x = 0, 0.50, and 1.0), which are novel phosphate materials developed as UV-shielding agents for use in cosmetics, were characterized by X-ray diffraction, X-ray fluorescent analysis, UV-vis reflectance, and Raman spectroscopy. Since the optical reflectance shifted to lower wavelengths by the crystallization of the phosphates and the stabilization of the amorphous state of the cerium-titanium pyrophosphates was carried out by doping niobium (Nb). Raman spectroscopic study of the phosphate showed that P-O-P bending and stretching modes decreased with the loading of Nb, accompanying with the formation of Nb-O stretching mode. Therefore, the increase in the amount of the non-bridging oxygen in the amorphous phosphate should be the reason for the inhibition of the crystallization. This stabilization is a significant improvement, which enables to apply these amorphous phosphates not only to cosmetics and paints, but also plastics and films

  19. Mesoscopic structure of cerium waste loaded hydrated cement by SANS

    International Nuclear Information System (INIS)

    Cementation is one of the most commonly used methods for conditioning radioactive wastes. It provides a cost-effective solution for encapsulation of low and intermediate level radioactive wastes into suitable solid form for long term safety storage. Cerium is used for decontamination of alpha contaminated metallic waste and after this decontamination process, secondary wastes with corrosion products are created, which must be managed properly and cemented for near surface disposal. In the present work, modification of mesoscopic structure in hydrated cement due to addition of simulated cerium waste at different concentrations has been investigated by small-angle neutron scattering (SANS). Structural modifications, in mesoscopic length scale, have been observed. The scattering profiles for three kinds of cement blocks (virgin, 10 g/l and 20 g/l of corrosion product (C.P.) with 4 mm thickness) are shown. Data have been analyzed in the light of polydisperse spherical particles model assuming a log-normal distribution. Widely separated bimodal particle size distributions best represent the present data. Further, it has been observed that the scattering profile obeys power-law (Q-n) behaviour in two domains of Q, which reflects the self-similar/self-affined morphology of the inhomogeneities. Estimated parameters from SANS data are tabulated. A comparison is shown mentioning the value of scattering radius of gyration, exponent values (η) and average particle size for each kind of hydrated cement sample. (author)

  20. MicroRNA-126 inhibits the proliferation of lung cancer cell line A549

    Institute of Scientific and Technical Information of China (English)

    Xun Yang; Bei-Bei Chen; Ming-Hua Zhang; Xin-Rong Wang

    2015-01-01

    Objective:To study the role of microRNA-126 in the development of lung cancer.Methods:The biological function of microRNA-126 was detected using EdU assay and CCK-8 assay;the target gene of microRNA-126 was analyzed using real time RT-PCR and Western blot assay.Results: In A549 cell line, overexpression of microRNA-126 inhibits the proliferation rate; VEGF is the target gene of microRNA-126; microRNA-126 exerts its function via regulating VEGF protein level.Conclusions: microRNA-126 inhibits the proliferation in A549 cell line.

  1. Ion exchange reactions in amorphous and crystalline aluminium silicates from solution of cerium salts

    International Nuclear Information System (INIS)

    Reactions of ion-exchange of Na+ by Ce3+ and NH4+ on the zeolite containing catalyst, amorphous silica alumina and zeolite Y have been studied. The cerium cations are shown to be exchanged by the Na+ cations with more selectivity than the anmonia cations. In the case of the zeolite containing catalyst and amorphous silica alumina the region of the staggered ion-exchange from the mixture of the solutions of cerium and ammonium sulphates was been detected. This is explained by the formation fo cerium complexes with the sulphate ions

  2. Effect of Cerium on Mechanical Properties and Morphology of ZZn4-1 Alloy

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Effect of the addition of cerium in appropriate amount on the mechanical properties and morphology of ZZn4-1 alloy was investigated. In the case of samples collected from metal mould, the results show that the addition of cerium in appropriate amount can increase tensile strength and HB hardness, and can refine the microstructure of ZZn4-1 alloy considerably. In the case of samples collected from pressure die-casting, the addition of cerium in appropriate amount can refine the primary η-phase and the eutectic structure of pressure die-casting and improve mechanical and processing properties of the alloy.

  3. 40 CFR 421.126 - Pretreatment standards for new sources.

    Science.gov (United States)

    2010-07-01

    ... § 421.126 Pretreatment standards for new sources. Except as provided in 40 CFR 403.7, any new source... 40 CFR part 403 and achieve the following pretreatment standards for new sources. The mass of... for monthly average mg/troy ounce of silver produced from leaching Copper .110 .053 Zinc .088...

  4. 27 CFR 9.126 - Santa Clara Valley.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Santa Clara Valley. 9.126... Santa Clara Valley. (a) Name. The name of the viticultural area described in this section is “Santa Clara Valley.” (b) Approved Maps. The appropriate maps for determining the boundaries of the...

  5. 21 CFR 152.126 - Frozen cherry pie.

    Science.gov (United States)

    2010-04-01

    ... and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION FRUIT PIES Requirements for Specific Standardized Fruit Pies § 152.126 Frozen cherry... of quality for frozen cherry pie is as follows: (i) The fruit content of the pie is such that...

  6. Candidates for Four Quasiparticle Chiral Structures in 126I

    Institute of Scientific and Technical Information of China (English)

    ZHENG; Yun; ZHU; Li-hua; WU; Xiao-guang; GAO; Zao-chun; HE; Chuang-ye; LI; Guang-sheng; WANG; Lie-lin; CHEN; Yong-shou; YU; Bei-bei; YAO; Shun-he; HAO; Xin; LIU; Ying; LI; Xue-qin; PAN; Bo

    2012-01-01

    <正>Since the first prediction of chirality in triaxial nuclei was pointed out by Frauendorf and Meng, nuclei in the A≈80, 100, 130, and 190 mass regions have been extensively studied in recent years to investigate the characteristics of nuclear chirality. Excited states in the doubly odd nucleus 126I were populated via heavy-ion fusion-evaporation

  7. 38 CFR 21.126 - Farm cooperative course.

    Science.gov (United States)

    2010-07-01

    ... (CONTINUED) VOCATIONAL REHABILITATION AND EDUCATION Vocational Rehabilitation and Employment Under 38 U.S.C. Chapter 31 Educational and Vocational Training Services § 21.126 Farm cooperative course. (a) Definition... rehabilitation services. The areas in which proficiency is to be established include: (1) Planning; (2)...

  8. 21 CFR 146.126 - Frozen concentrate for colored lemonade.

    Science.gov (United States)

    2010-04-01

    ... lemonade by § 146.120, except that it is colored with a safe and suitable fruit juice, vegetable juice, or... Section 146.126 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION CANNED FRUIT JUICES Requirements for Specific Standardized...

  9. 10 CFR 72.126 - Criteria for radiological protection.

    Science.gov (United States)

    2010-01-01

    ....126 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) LICENSING REQUIREMENTS FOR THE INDEPENDENT STORAGE OF SPENT NUCLEAR FUEL, HIGH-LEVEL RADIOACTIVE WASTE, AND REACTOR-RELATED GREATER THAN CLASS C... exposed to radiation or airborne radioactive materials. Structures, systems, and components for...

  10. Studies of solution deposited cerium oxide thin films on textured Ni-alloy substrates for YBCO superconductor

    International Nuclear Information System (INIS)

    Cerium oxide (CeO2) buffer layers play an important role for the development of YBa2Cu3O7-x (YBCO) based superconducting tapes using the rolling assisted biaxially textured substrates (RABiTS) approach. The chemical solution deposition (CSD) approach has been used to grow epitaxial CeO2 films on textured Ni-3 at.% W alloy substrates with various starting precursors of ceria. Precursors such as cerium acetate, cerium acetylacetonate, cerium 2-ethylhexanoate, cerium nitrate, and cerium trifluoroacetate were prepared in suitable solvents. The optimum growth conditions for these cerium precursors were Ar-4% H2 gas processing atmosphere, solution concentration levels of 0.2-0.5 M, a dwell time of 15 min, and a process temperature range of 1050-1150 deg. C. X-ray diffraction, AFM, SEM, and optical microscopy were used to characterize the CeO2 films. Highly textured CeO2 layers were obtained on Ni-W substrates with both cerium acetate and cerium acetylacetonate as starting precursors. YBCO films with a J c of 1.5 MA/cm2 were obtained on cerium acetylacetonate-based CeO2 films with sputtered YSZ and CeO2 cap layers

  11. Study on Catalysts with Rhodium Loading on Different Cerium-Zirconium Mixed Oxides

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The catalysts with Rh loading on different cerium-zirconium mixed oxides were characterized by BET, H2-TPR and OSC. The effects of different cerium-zirconium mixed oxides on catalytic performance and thermal stability of Rh loaded catalyst were studied. The results show that: (1) Rh can enhance cerium-zirconium mixed oxides OSC and catalytic reaction rates; (2) cerium-zirconium mixed oxides with high Ce contents and low Zr contents are more favorable to the stability of catalysts. Moreover, the contents of CeO2 have important effect on catalysts characteristics, and the addition of some rare earth components, such as La, Pr and Nd also have some influences.

  12. Immobilization of simulated radioactive soil waste containing cerium by self-propagating high-temperature synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Mao, Xianhe, E-mail: maoxianhe@hotmail.com; Qin, Zhigui; Yuan, Xiaoning; Wang, Chunming; Cai, Xinan; Zhao, Weixia; Zhao, Kang; Yang, Ping; Fan, Xiaoling

    2013-11-15

    A simulated radioactive soil waste containing cerium as an imitator element has been immobilized by a thermite self-propagating high-temperature synthesis (SHS) process. The compositions, structures, and element leaching rates of products with different cerium contents have been characterized. To investigate the influence of iron on the chemical stability of the immobilized products, leaching tests of samples with different iron contents with different leaching solutions were carried out. The results showed that the imitator element cerium mainly forms the crystalline phases CeAl{sub 11}O{sub 18} and Ce{sub 2}SiO{sub 5}. The leaching rate of cerium over a period of 28 days was 10{sup −5}–10{sup −6} g/(m{sup 2} day). Iron in the reactants, the reaction products, and the environment has no significant effect on the chemical stability of the immobilized SHS products.

  13. Immobilization of simulated radioactive soil waste containing cerium by self-propagating high-temperature synthesis

    Science.gov (United States)

    Mao, Xianhe; Qin, Zhigui; Yuan, Xiaoning; Wang, Chunming; Cai, Xinan; Zhao, Weixia; Zhao, Kang; Yang, Ping; Fan, Xiaoling

    2013-11-01

    A simulated radioactive soil waste containing cerium as an imitator element has been immobilized by a thermite self-propagating high-temperature synthesis (SHS) process. The compositions, structures, and element leaching rates of products with different cerium contents have been characterized. To investigate the influence of iron on the chemical stability of the immobilized products, leaching tests of samples with different iron contents with different leaching solutions were carried out. The results showed that the imitator element cerium mainly forms the crystalline phases CeAl11O18 and Ce2SiO5. The leaching rate of cerium over a period of 28 days was 10-5-10-6 g/(m2 day). Iron in the reactants, the reaction products, and the environment has no significant effect on the chemical stability of the immobilized SHS products.

  14. The low gas flow rate foam separation of cerium(III) from dilute aqueous solutions

    International Nuclear Information System (INIS)

    Two low gas flow rate foam separation techniques, ion and precipitate flotation, have been investigated for the separation of trivalent cerium from solutions with initial cerium concentrations ranging from 1 x 10-8 to 1 x 10-4M in the pH range of 1.8 to 12 using the anionic collector sodium lauryl sulphate and the cationic surfactant cetyl trymethyl ammonium bromide. In addition to the type of collector, the pH and the cerium ion concentration, and other factors which can affect flotation results, viz. the time period of bubbling, the rate of gas flow, the ageing of both the cerium and the collector ions, the ionic strength, and the concentration of the collector ions have been investigated and optimum conditions have been established. Under optimum conditions removals as high a 98.5% can be achieved. (author)

  15. Inhibition of pH fronts in corrosion cells due to the formation of cerium hydroxide

    International Nuclear Information System (INIS)

    The effect of cerium-based corrosion inhibitors on the pH front between the alkaline cathode and acidic anode in corrosion cells has been studied. The cerium component of these inhibitors can affect the pH front since it precipitates in an alkaline environment as cerium hydroxide, which is important since the corrosion inhibition mechanism of the cerium component is a result of its deposition as a highly electrical resistive (passivation) layer on the cathode. It is studied whether the cerium can reach the cathode when fed into the corrosion cell from an external source after the onset of corrosion. To this end a simulation model was set up that includes the Poisson–Nernst–Planck theory to describe ion transport and the Frumkin–Butler–Volmer equation to describe charge transfer at the electrodes. In this model both the self-dissociation of water and the formation of cerium hydroxide are taken into account. To support our findings experimentally a corrosion cell consisting of an aluminum and copper electrode was used, in which the pH fronts were visualized using a pH-indicator. Two types of inhibitors were used; namely, highly soluble CeCl3 and sparsely soluble cerium dibutylphosphate, Ce(dbp)3. The results show that CeCl3 can reduce the size of the alkaline region and reach the cathode to form a passivation layer, whereas the solubility in case of Ce(dbp)3 is too low to supply sufficient amounts of trivalent cerium cations to penetrate the alkaline region. This behavior can be explained by the simulation results, which reveal a threshold for the corrosion inhibitor solubility below which no passivation of the cathode occurs

  16. Catalysts with Cerium in a Membrane Reactor for the Removal of Formaldehyde Pollutant from Water Effluents

    OpenAIRE

    Mirella Gutiérrez-Arzaluz; Luis Noreña-Franco; Saúl Ángel-Cuevas; Violeta Mugica-Álvarez; Miguel Torres-Rodríguez

    2016-01-01

    We report the synthesis of cerium oxide, cobalt oxide, mixed cerium, and cobalt oxides and a Ce–Co/Al2O3 membrane, which are employed as catalysts for the catalytic wet oxidation (CWO) reaction process and the removal of formaldehyde from industrial effluents. Formaldehyde is present in numerous waste streams from the chemical industry in a concentration low enough to make its recovery not economically justified but high enough to create an environmental hazard. Common biological degradation ...

  17. Protein adsorption and cellular uptake of cerium oxide nanoparticles as a function of zeta potential

    OpenAIRE

    Patil, Swanand; Sandberg, Amanda; Heckert, Eric; Self, William; Seal, Sudipta

    2007-01-01

    The surface chemistry of biomaterials can have a significant impact on their performance in biological applications. Our recent work suggests that cerium oxide nanoparticles are potent antioxidants in cell culture models and we have evaluated several therapeutic applications of these nanoparticles in different biological systems. Knowledge of protein adsorption and cellular uptake will be very useful in improving the beneficial effects of cerium oxide nanoparticles in biology. In the present ...

  18. Effects of Morphology of Cerium Oxide Catalysts for Reverse Water Gas Shift Reaction

    OpenAIRE

    Kovasevic, M.; Mojet, B.L.; Ommen, van, B.; Lefferts, L.

    2016-01-01

    Reverse water gas shift reaction (RWGS) was investigated over cerium oxide catalysts of distinct morphologies: cubes, rods and particles. Catalysts were characterized by X-ray diffraction, Raman spectroscopy and temperature programmed reduction (TPR) in hydrogen. Nanoshapes with high concentration of oxygen vacancies contain less surface oxygen removable in TPR. Cerium oxide cubes exhibited two times higher activity per surface area as compared to rods and particles. Catalytic activity of the...

  19. A chemical cleaning process with Cerium (IV)-sulfuric acid

    International Nuclear Information System (INIS)

    A chemical cleaning process with a high decontamination factor (DF) is requested for decommissioning. Usually, the process should be qualified with the features, such as the feasibility of treating large or complicated form waste, the minimization of secondary waste. Therefore, a powerful technique of redox decontamination process with Ce+4/Ce+3 has been studied at INER. First, the redox of cerium ion with electrolytic method was developed. Two kinds of home-made electrolyzer were used. One is with an ion-exchange membrane, and the other one is with a ceramic separator. Second, factors influencing the decontamination efficiency, such as the concentration of Ce+4, regeneration current density, temperature, acidity of solution were all studied experimentally, and the optimum conditions were specified too. Third, the liquid waste recycling and treatment were developed with electrodialysis and ion-exchange absorption methods. Finally, the hot test was proceeded with the contaminated metals from DCR of nuclear facility. (author)

  20. Effect of Surface Modification on Behaviors of Cerium Oxide Nanopowders

    Institute of Scientific and Technical Information of China (English)

    Li Mei; Shi Zhenxue; Liu Zhaogang; Hu Yanhong; Wang Mitang; Li Hangquan

    2007-01-01

    Study was made on the effect of surface modification on the behaviors of cerium oxide nanopowders. A surfactant-sodium dodecyl sulfate(C12H25SO4Na) was used to modify the surface of CeO2 powder particles. The unmodified and modified CeO2 powders were characterized by using a powder comprehensive characteristic tester, laser particle size analyzer, specific surface area tester, X-ray diffraction tester, and a scanning electron microscope. The testing and analysis results showed that C12H25SO4Na surface modification might increase the flowability and dispersity, and decrease the specific surface area and agglomeration of CeO2 powders. The mechanism of the surface modification of CeO2 powder particles was also discussed.

  1. Modification mechanism of cerium on the Al-18Si alloy

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The effect of the rare earth cerium (Ce) on the hypereutectic Al-Si alloy under different casting states have been studied by optical microscope and quantitative image analysis. It is found that the size and the quantity of primary silicon in castings decrease with the increase of added Ce in the melt. Meanwhile primary silicon changes from branched shape to fine facetted shape. Although the modification on eutectic silicon in castings also improves with the increase of added Ce in the melt, the effect of modification on eutectic silicon away from primary silicon is more obvious than that on eutectic silicon close to primary silicon. The modification mechanism was analyzed in detail by means of scanning electron microscope equipped with energy dispersive analysis of X-ray and thermodynamics analysis, which included the analysis on the change in standard Gibbs energy of reaction and reaction equilibrium.

  2. Cerium intermetallics with TiNiSi-type structure

    Energy Technology Data Exchange (ETDEWEB)

    Janka, Oliver; Niehaus, Oliver; Poettgen, Rainer [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie; Chevalier, Bernard [Bordeaux Univ. CNRS (UPR 9048), Pessac (France). Inst. de Chimie de la Matiere Condensee de Bordeaux (ICMCB)

    2016-08-01

    Intermetallic compounds with the equiatomic composition CeTX that crystallize with the orthorhombic TiNiSi-type structure can be synthesized with electron-rich transition metals (T) and X = Zn, Al, Ga, Si, Ge, Sn, As, Sb, and Bi. The present review focusses on the crystal chemistry and chemical bonding of these CeTX phases and on their physical properties, {sup 119}Sn and {sup 121}Sb Moessbauer spectra, high-pressure effects, hydrogenation reactions and the formation of solid solutions in order to elucidate structure-property relationships. This paper is the final one of a series of four reviews on equiatomic intermetallic cerium compounds [Part I: Z. Naturforsch. 2015, 70b, 289; Part II: Z. Naturforsch. 2015, 70b, 695; Part III: Z. Naturforsch. 2016, 71b, 165].

  3. On the mixed nature of cerium conversion coatings

    Energy Technology Data Exchange (ETDEWEB)

    Botana, F.J.; Aballe, A.; Bethencourt, M.; Cano, M.J. [Cadiz Univ. (Spain). Dept. de Ciencia de los Materiales e Ingenieria Metalurgica y Quimica Inorganica; Marcos, M. [Cadiz Univ. (Spain). Dept. de Ingenieria Mecanica y Diseno Industrial

    2002-03-01

    Alternative pretreatments are currently under development in order to avoid the environmental impact produced by using surface finishing processes based on chromates. Some of the environmentally friendly alternatives proposed involve the use of lanthanide based compounds. In this study, conversion coatings on AA5083 (Al-Mg) samples developed using full immersion pretreatments in 500 ppm CeCl{sub 3} aqueous solutions have been investigated. Their microscopic and compositional features have been analyzed using SEM images and EDS spectra. From this analysis it has been determined that this layer over the surface of the samples is of a heterogeneous composition. This coating is formed by an alumina coating covering the aluminum matrix and dispersed cerium-rich islands deposited over the cathodic sites of the alloy. A characterization methodology is proposed based on the utilization of different electrochemical techniques, such as open circuit potential monitoring (OCP), linear polarization (LP) and electrochemical impedance spectroscopy (EIS). (orig.)

  4. Characterization of a zinc-cerium flow battery

    Science.gov (United States)

    Leung, P. K.; Ponce-de-León, C.; Low, C. T. J.; Shah, A. A.; Walsh, F. C.

    The performance of a divided, parallel-plate zinc-cerium redox flow battery using methanesulfonic acid electrolytes was studied. Eight two and three-dimensional electrodes were tested under both constant current density and constant cell voltage discharge. Carbon felt and the three-dimensional platinised titanium mesh electrodes exhibited superior performance over the 2-dimensional electrodes. The charge and discharge characteristics of the redox flow battery were studied under different operating conditions and Zn/Ce reactant, as well as methansulfonic acid concentration. The cell performance improved at higher operating temperatures and faster electrolyte flow velocities. The number of possible cycles increased at reduced states of charge. During 15 min charge/discharge per cycle experiment, 57 cycles were obtained and the zinc reaction was found to be the limiting process during long term operation.

  5. Interplay of spin-orbit and entropic effects in cerium

    Energy Technology Data Exchange (ETDEWEB)

    Lanata, Nicola [Rutgers University; Yao, Yong-Xin [Ames Laboratory; Wang, Cai-Zhuang [Ames Laboratory; Ho, Kai-Ming [Ames Laboratory; Kotliar, Gabriel [Rutgers University

    2014-10-01

    We perform first-principles calculations of elemental cerium and compute its pressure-temperature phase diagram, finding good quantitative agreement with the experiments. Our calculations indicate that, while a signature of the volume-collapse transition appears in the free energy already at low temperatures, at higher temperatures this signature is enhanced because of the entropic effects, and originates an actual thermodynamical instability. Furthermore, we find that the catalyst determining this feature is—in all temperature regimes—a pressure-induced effective reduction of the f-level degeneracy due to the spin-orbit coupling. Our analysis suggests also that the lattice vibrations might be crucial in order to capture the behavior of the pressure-temperature transition line at large temperatures.

  6. Growth of transition metals on cerium tungstate model catalyst layers

    Science.gov (United States)

    Skála, T.; Tsud, N.; Stetsovych, V.; Mysliveček, J.; Matolín, V.

    2016-10-01

    Two model catalytic metal/oxide systems were investigated by photoelectron spectroscopy and scanning tunneling microscopy. The mixed-oxide support was a cerium tungstate epitaxial thin layer grown in situ on the W(1 1 0) single crystal. Active particles consisted of palladium and platinum 3D islands deposited on the tungstate surface at 300 K. Both metals were found to interact weakly with the oxide support and the original chemical state of both support and metals was mostly preserved. Electronic and morphological changes are discussed during the metal growth and after post-annealing at temperatures up to 700 K. Partial transition-metal coalescence and self-cleaning from the CO and carbon impurities were observed.

  7. Mechanochemical synthesis and spark plasma sintering of the cerium silicides

    International Nuclear Information System (INIS)

    Highlights: • Ce5Si3, Ce3Si2, CeSi, CeSi2−x and CeSi2 were mechanochemically synthesized. • Temperature and pressure were monitored to investigate reaction progress. • All syntheses proceeded through a MSR event followed by rapid solid-state diffusion. • Milling time before MSR correlates well with effective heat of formation. • Some synthesized material was densified by spark plasma sintering. - Abstract: The cerium silicides, Ce5Si3, Ce3Si2, CeSi, CeSi2−y, and CeSi2−x, have been prepared from the elements by mechanochemical processing in a planetary ball mill. Preparation of the cerium silicide Ce5Si4 was unsuccessfully attempted and potential reasons for this are discussed. Temperature and pressure of the milling vial were monitored in situ to gain insight into the mechanochemical reaction kinetics, which include a mechanically-induced self-propagating reaction (MSR). Some prepared powders were consolidated by spark plasma sintering to high density. Starting materials, as-milled powders, and consolidated samples were characterized by X-ray diffraction, scanning electron microscopy, and energy dispersive spectroscopy. The results obtained help elucidate key questions in mechanochemical processing of intermetallics, showing first phase formation similar to thin films, MSR ignition times that are composition- and milling speed-dependent, and sensitivity of stable compound formation on the impact pressure. The results demonstrate mechanochemical synthesis as a viable technique for rare earth silicides

  8. Mechanochemical synthesis and spark plasma sintering of the cerium silicides

    Energy Technology Data Exchange (ETDEWEB)

    Alanko, Gordon A.; Jaques, Brian; Bateman, Allyssa [Department of Materials Science and Engineering, College of Engineering, Boise State University, 1910 University Drive, Boise, ID 83725 (United States); Butt, Darryl P., E-mail: darrylbutt@boisestate.edu [Department of Materials Science and Engineering, College of Engineering, Boise State University, 1910 University Drive, Boise, ID 83725 (United States); Center for Advanced Energy Studies, 995 University Boulevard, Idaho Falls, ID 83401 (United States)

    2014-12-15

    Highlights: • Ce{sub 5}Si{sub 3}, Ce{sub 3}Si{sub 2}, CeSi, CeSi{sub 2−x} and CeSi{sub 2} were mechanochemically synthesized. • Temperature and pressure were monitored to investigate reaction progress. • All syntheses proceeded through a MSR event followed by rapid solid-state diffusion. • Milling time before MSR correlates well with effective heat of formation. • Some synthesized material was densified by spark plasma sintering. - Abstract: The cerium silicides, Ce{sub 5}Si{sub 3}, Ce{sub 3}Si{sub 2}, CeSi, CeSi{sub 2−y}, and CeSi{sub 2−x}, have been prepared from the elements by mechanochemical processing in a planetary ball mill. Preparation of the cerium silicide Ce{sub 5}Si{sub 4} was unsuccessfully attempted and potential reasons for this are discussed. Temperature and pressure of the milling vial were monitored in situ to gain insight into the mechanochemical reaction kinetics, which include a mechanically-induced self-propagating reaction (MSR). Some prepared powders were consolidated by spark plasma sintering to high density. Starting materials, as-milled powders, and consolidated samples were characterized by X-ray diffraction, scanning electron microscopy, and energy dispersive spectroscopy. The results obtained help elucidate key questions in mechanochemical processing of intermetallics, showing first phase formation similar to thin films, MSR ignition times that are composition- and milling speed-dependent, and sensitivity of stable compound formation on the impact pressure. The results demonstrate mechanochemical synthesis as a viable technique for rare earth silicides.

  9. Thermal Treatment of Cerium Oxide and Its Properties: Adsorption Ability versus Degradation Efficiency

    Directory of Open Access Journals (Sweden)

    Pavel Janoš

    2014-01-01

    Full Text Available Cerium oxide belongs to the most important heterogeneous catalysts, but its applicability as so-called reactive sorbent for the degradation of toxic chemicals was only recently discovered. For these purposes, cerium oxide is prepared by precipitation of insoluble cerium salts (carbonates with a subsequent thermal decomposition. Properties of cerium oxide prepared from the carbonate precursor are strongly affected by the temperature during the calcination. Main physicochemical properties of cerium oxide (specific surface area, crystallinity, and surface chemistry were examined in dependence on the calcination temperature. As the adsorptive properties of CeO2 are undoubtedly of great importance in the abovementioned applications, the adsorption ability was studied using an azo dye Acid Orange 7 (AO7 as a model compound. The highest sorption efficiency towards AO7 exhibited sorbents prepared at temperatures below 700°C, which was attributed mainly to the presence of hydroxyl groups on the oxide surface. A strong correlation was found between an adsorption efficiency of cerium oxides and their degradation efficiency for organophosphate pesticide parathion methyl. The >Ce–OH groups on the sorbent surface are responsible for the dye binding by the surface-complexation mechanism, and probably also for the nucleophilic cleavage of the P–O–aryl bond in the pesticide molecule.

  10. Copper, Boron, and Cerium Additions in Type 347 Austenitic Steel to Improve Creep Rupture Strength

    Science.gov (United States)

    Laha, Kinkar; Kyono, J.; Shinya, Norio

    2012-04-01

    Type 347 austenitic stainless steel (18Cr-12Ni-Nb) was alloyed with copper (3 wt pct), boron (0.01 to 0.06 wt pct), and cerium (0.01 wt pct) with an aim to increase the creep rupture strength of the steel through the improved deformation and cavitation resistance. Short-term creep rupture strength was found to increase with the addition of copper in the 347 steel, but the long-term strength was inferior. Extensive creep cavitation deprived the steel of the beneficial effect of creep deformation resistance induced by nano-size copper particles. Boron and cerium additions in the copper-containing steel increased its creep rupture strength and ductility, which were more for higher boron content. Creep deformation, grain boundary sliding, and creep cavity nucleation and growth in the steel were found to be suppressed by microalloying the copper-containing steel with boron and cerium, and the suppression was more for higher boron content. An auger electron spectroscopic study revealed the segregation of boron instead of sulfur on the cavity surface of the boron- and cerium-microalloyed steel. Cerium acted as a scavenger for soluble sulfur in the steels through the precipitation of cerium sulfide (CeS). This inhibited the segregation of sulfur and facilitated the segregation of boron on cavity surface. Boron segregation on the nucleated cavity surface reduced its growth rate. Microalloying the copper-containing 347 steel with boron and cerium thus enabled to use the full extent of creep deformation resistance rendered by copper nano-size particle by increase in creep rupture strength and ductility.

  11. Exposure, Health and Ecological Effects Review of Engineered Nanoscale Cerium and Cerium Oxide Associated with its Use as a Fuel Additive

    Science.gov (United States)

    Advances of nanoscale science have produced nanomaterials with unique physical and chemical properties at commercial levels which are now incorporated into over 1000 products. Nanoscale cerium (di) oxide (CeO(2)) has recently gained a wide range of applications which includes coa...

  12. Exposure and Health Effects Review of Engineered Nanoscale Cerium and Cerium Dioxide Associated with its Use as a Fuel Additive - NOW IN PRINT IN THE JOURNAL

    Science.gov (United States)

    Advances of nanoscale science have produced nanomaterials with unique physical and chemical properties at commercial levels that are now incorporated into over 1000 products. Nanoscale cerium (di) oxide (Ce02) has recently gained a wide range of applications which includes coatin...

  13. 7 CFR 1.26 - Representation before the Department of Agriculture.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 1 2010-01-01 2010-01-01 false Representation before the Department of Agriculture. 1.26 Section 1.26 Agriculture Office of the Secretary of Agriculture ADMINISTRATIVE REGULATIONS Departmental Proceedings § 1.26 Representation before the Department of Agriculture. (a) Applicability....

  14. 17 CFR 1.26 - Deposit of instruments purchased with customer funds.

    Science.gov (United States)

    2010-04-01

    ... purchased with customer funds. 1.26 Section 1.26 Commodity and Securities Exchanges COMMODITY FUTURES TRADING COMMISSION GENERAL REGULATIONS UNDER THE COMMODITY EXCHANGE ACT Customers' Money, Securities, and Property § 1.26 Deposit of instruments purchased with customer funds. (a) Each futures commission...

  15. 40 CFR 89.126 - Denial, revocation of certificate of conformity.

    Science.gov (United States)

    2010-07-01

    ... conformity. 89.126 Section 89.126 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Standards and Certification Provisions § 89.126 Denial, revocation of certificate of conformity. (a) If... issued certificate of conformity if the Administrator finds any one of the following infractions to...

  16. Determination of Atom Number of Fission Product 126Sn by γ-ray Spectrometry

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>126Sn is a long-lived beta emitting radionuclide with a half-life of (2.35±0.07)×105 years[1]. Artificially produced 126Sn has entered our environment through nuclear weapons testing and released from reprocessing plants and may locally lead to strongly enhanced 126Sn concentrations. So the long

  17. 33 CFR 126.30 - What are the conditions for conducting welding and hotwork?

    Science.gov (United States)

    2010-07-01

    ... conducting welding and hotwork? 126.30 Section 126.30 Navigation and Navigable Waters COAST GUARD, DEPARTMENT... FACILITIES § 126.30 What are the conditions for conducting welding and hotwork? (a) The facility operator must ensure that all welding or hotwork conducted at the facility meets the requirements of...

  18. 12 CFR 225.126 - Activities not closely related to banking.

    Science.gov (United States)

    2010-01-01

    ... 12 Banks and Banking 3 2010-01-01 2010-01-01 false Activities not closely related to banking. 225.126 Section 225.126 Banks and Banking FEDERAL RESERVE SYSTEM (CONTINUED) BOARD OF GOVERNORS OF THE... Financial Holding Companies Interpretations § 225.126 Activities not closely related to banking. Pursuant...

  19. 27 CFR 24.126 - Change in proprietorship involving a bonded wine warehouse.

    Science.gov (United States)

    2010-04-01

    ... involving a bonded wine warehouse. 24.126 Section 24.126 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS WINE Establishment and Operations Changes Subsequent to Original Establishment § 24.126 Change in proprietorship involving a bonded wine...

  20. 13 CFR 126.615 - May a large business participate on a HUBZone contract?

    Science.gov (United States)

    2010-01-01

    ... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false May a large business participate on a HUBZone contract? 126.615 Section 126.615 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION HUBZONE PROGRAM Contractual Assistance § 126.615 May a large business participate on a...

  1. 126 novel mutations in Italian patients with neurofibromatosis type 1

    OpenAIRE

    Bianchessi, Donatella; Morosini, Sara; Saletti, Veronica; Ibba, Maria Cristina; Natacci, Federica; Esposito, Silvia; Cesaretti, Claudia; Riva, Daria; Finocchiaro, Gaetano; Eoli, Marica

    2015-01-01

    Abstract Genetic analysis of Neurofibromatosis type 1 (NF1) may facilitate the identification of patients in early phases of the disease. Here, we present an overview of our diagnostic research spanning the last 11 years, with a focus on the description of 225 NF1 mutations, 126 of which are novel, found in a series of 607 patients (513 unrelated) in Italy. Between 2003 and 2013, 443 unrelated patients were profiled by denaturing high pressure liquid chromatography (DHPLC) analysis of 60 ampl...

  2. Catalysts with Cerium in a Membrane Reactor for the Removal of Formaldehyde Pollutant from Water Effluents.

    Science.gov (United States)

    Gutiérrez-Arzaluz, Mirella; Noreña-Franco, Luis; Ángel-Cuevas, Saúl; Mugica-Álvarez, Violeta; Torres-Rodríguez, Miguel

    2016-01-01

    We report the synthesis of cerium oxide, cobalt oxide, mixed cerium, and cobalt oxides and a Ce-Co/Al₂O₃ membrane, which are employed as catalysts for the catalytic wet oxidation (CWO) reaction process and the removal of formaldehyde from industrial effluents. Formaldehyde is present in numerous waste streams from the chemical industry in a concentration low enough to make its recovery not economically justified but high enough to create an environmental hazard. Common biological degradation methods do not work for formaldehyde, a highly toxic but refractory, low biodegradability substance. The CWO reaction is a recent, promising alternative that also permits much lower temperature and pressure conditions than other oxidation processes, resulting in economic benefits. The CWO reaction employing Ce- and Co-containing catalysts was carried out inside a slurry batch reactor and a membrane reactor. Experimental results are reported. Next, a mixed Ce-Co oxide film was supported on an γ-alumina membrane used in a catalytic membrane reactor to compare formaldehyde removal between both types of systems. Catalytic materials with cerium and with a relatively large amount of cerium favored the transformation of formaldehyde. Cerium was present as cerianite in the catalytic materials, as indicated by X-ray diffraction patterns. PMID:27231888

  3. Thermal expansion and stability of cerium-doped Lu2SiO5

    International Nuclear Information System (INIS)

    In-situ X-ray diffraction, differential scanning calorimetry and dilatometry were used to measure the thermal expansion and thermal stability of cerium-doped Lu2SiO5. The thermal expansion of Lu2SiO5 was highly anisotropic, with expansion along the b- and c-axes 5-10 times greater than expansion along the a-axis. There were no measurable differences in the thermal expansion between undoped Lu2SiO5, cerium-doped Lu2SiO5 with high scintillation efficiency, cerium-doped Lu2SiO5 with low scintillation efficiency and annealed cerium-doped Lu2SiO5. Lu2SiO5 decomposed at temperatures as low as 1350 deg. C in 2, while the presence of 100-150 ppm O2 stabilized Lu2SiO5 at temperatures up to 1760 deg. C. No bulk defects were identified to account for the difference between high scintillation efficiency and low scintillation efficiency cerium-doped Lu2SiO5 samples

  4. Effect of cerium loading on structure and morphology of modified Ce-USY zeolites

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, Fillipe A.C.; Araujo, Daniel R.; Silva, Junia C.M.; Macedo, Julio L. de; Dias, Silvia C.L.; Dias, Jose A., E-mail: scdias@unb.br, E-mail: jdias@unb.br [Laboratorio de Catalise, Instituto de Quimica, Faculdade UnB-Gama, Universidade de Brasilia, DF (Brazil); Ghesti, Grace F. [Engenharia de Energia, Faculdade UnB-Gama, Universidade de Brasilia, DF (Brazil); Filho, Geraldo N.R. [Centro de Ciencias Exatas e Naturais, Universidade Federal do Para, Belem, PA (Brazil)

    2011-09-15

    This work describes comprehensibly the effect of cerium loading on the structure and morphology of NH{sub 4}USY zeolite. The Ce-USY (2-25 wt.% of CeO{sub 2}) was obtained by wet impregnation of CeCl{sub 3} followed by calcination at 550 deg C for 8 h. At low loadings (2-10%), cerium species are mainly located at ion exchange positions in the framework, whereas at higher loadings (15.25%), small aggregates were formed on the HUSY surface. X-ray diffractograms (XRD) exhibited only the reflections related to HUSY, demonstrating the high dispersion of cerium species, but Fourier transform Raman spectroscopy (FT-Raman) detected CeO{sub x} for the materials above 10%. Reaction of CeCl{sub 3} with NH{sub 4}USY produced NH{sub 4}Cl, which decomposed to form HCl, leading to framework dealumination. The materials showed an increased Lewis/Bronsted ratio with increasing cerium loadings due to the interaction between the excess cerium and the OH groups of USY, and the consequent formation of CeO{sub x} species. (author)

  5. Exposure of cerium oxide nanoparticles to kidney bean shows disturbance in the plant defense mechanisms.

    Science.gov (United States)

    Majumdar, Sanghamitra; Peralta-Videa, Jose R; Bandyopadhyay, Susmita; Castillo-Michel, Hiram; Hernandez-Viezcas, Jose-Angel; Sahi, Shivendra; Gardea-Torresdey, Jorge L

    2014-08-15

    Overwhelming use of engineered nanoparticles demands rapid assessment of their environmental impacts. The transport of cerium oxide nanoparticles (nCeO2) in plants and their impact on cellular homeostasis as a function of exposure duration is not well understood. In this study, kidney bean plants were exposed to suspensions of ∼ 8 ± 1 nm nCeO2 (62.5 to 500 mg/L) for 15 days in hydroponic conditions. Plant parts were analyzed for cerium accumulation after one, seven, and 15 days of nCeO2 exposure. The primary indicators of stress like lipid peroxidation, antioxidant enzyme activities, total soluble protein and chlorophyll contents were studied. Cerium in tissues was localized using scanning electron microscopy and synchrotron μ-XRF mapping, and the chemical forms were identified using μ-XANES. In the root epidermis, cerium was primarily shown to exist as nCeO2, although a small fraction (12%) was biotransformed to Ce(III) compound. Cerium was found to reach the root vascular tissues and translocate to aerial parts with time. Upon prolonged exposure to 500 mg nCeO2/L, the root antioxidant enzyme activities were significantly reduced, simultaneously increasing the root soluble protein by 204%. In addition, leaf's guaiacol peroxidase activity was enhanced with nCeO2 exposure in order to maintain cellular homeostasis. PMID:24981679

  6. Electrochemical deposition of cerium on porous silicon to improve photoluminescence properties

    Energy Technology Data Exchange (ETDEWEB)

    Atyaoui, Malek, E-mail: atyaoui.malek@yahoo.fr [Laboratoire de Photovoltaieque, Centre de Recherches et des Technologies de l' energie, PB:95, Hammam Lif 2050 (Tunisia); Dimassi, Wissem; Monther, Ghrib; Chtourou, Radhouane; Ezzaouia, Hatem [Laboratoire de Photovoltaieque, Centre de Recherches et des Technologies de l' energie, PB:95, Hammam Lif 2050 (Tunisia)

    2012-02-15

    In this work, we present results for Cerium (Ce) doping effects on photoluminescence (PL) properties of porous silicon (PS). Cerium was deposited using electrochemical deposition on porous silicon prepared by electrochemical anodization of P-type (100) Si. From the photoluminescence spectroscopy, it was shown that porous silicon treated with cerium can lead to an increase of photoluminescence when they are irradiated by light compared to the porous silicon layer without cerium. In order to understand the contribution of cerium to the enhanced photoluminescence, energy dispersive X-ray (EDX) spectroscopy, Fourier transmission infrared spectroscopy (FTIR), X-ray diffraction (XRD) and atomic force microscopy (AFM) were performed, and it was shown that the improved photoluminescence may be attributed to the change of Si-H bonds into Si-O-Ce bonds and to a newly formed PS layer during electrochemical Ce coating. - Highlights: Black-Right-Pointing-Pointer Degradation of the surface structures and the PL properties of PS remains a key issue for industrial production. Black-Right-Pointing-Pointer In order to solve this problem, the passivation of the PS surface by treating it with Ce is investigated. Black-Right-Pointing-Pointer To understand the effects of Ce on PL properties, EDX, FTIR, XRD, AFM and UV-vis analysis were performed.

  7. Catalysts with Cerium in a Membrane Reactor for the Removal of Formaldehyde Pollutant from Water Effluents

    Directory of Open Access Journals (Sweden)

    Mirella Gutiérrez-Arzaluz

    2016-05-01

    Full Text Available We report the synthesis of cerium oxide, cobalt oxide, mixed cerium, and cobalt oxides and a Ce–Co/Al2O3 membrane, which are employed as catalysts for the catalytic wet oxidation (CWO reaction process and the removal of formaldehyde from industrial effluents. Formaldehyde is present in numerous waste streams from the chemical industry in a concentration low enough to make its recovery not economically justified but high enough to create an environmental hazard. Common biological degradation methods do not work for formaldehyde, a highly toxic but refractory, low biodegradability substance. The CWO reaction is a recent, promising alternative that also permits much lower temperature and pressure conditions than other oxidation processes, resulting in economic benefits. The CWO reaction employing Ce- and Co-containing catalysts was carried out inside a slurry batch reactor and a membrane reactor. Experimental results are reported. Next, a mixed Ce–Co oxide film was supported on an γ-alumina membrane used in a catalytic membrane reactor to compare formaldehyde removal between both types of systems. Catalytic materials with cerium and with a relatively large amount of cerium favored the transformation of formaldehyde. Cerium was present as cerianite in the catalytic materials, as indicated by X-ray diffraction patterns.

  8. Effects of precipitate aging time on the cerium-zirconium composite oxides

    Institute of Scientific and Technical Information of China (English)

    钟强; 崔梅生; 岳梅; 王琦; 王磊; 郭荣贵; 龙志奇; 黄小卫

    2014-01-01

    Cerium-zirconium composite oxides with high performance were synthesized by a co-precipitation method, using zirco-nium oxychloride and rare earth chloride as raw materials. The effects of precipitate aging time on the properties of cerium-zirconium composite oxides were investigated. The prepared cerium-zirconium composite oxides were characterized by X-ray diffraction (XRD), BET specific surface area, pulsed oxygen chemical adsorption, H2 temperature-programmed-reduction (H2-TPR), scanning electron microscopy (SEM), etc. The results showed that the precipitate aging time caused great effects on the properties of cerium zirconium composite oxides. With the increase of aging time, the cerium zirconium composite oxides showed enhanced specific sur-face area, good thermal stability, and high oxygen storage capacity (OSC). The best performance sample was obtained while the pre-cipitate aging time up to 48 h, with the specific surface area of 140.7 m2/g, and OSC of 657.24μmolO2/g for the fresh sample. Even after thermal aged under 1000 ºC for 4 h, the aged specific surface area was 41.6 m2/g, moreover with a good OSC of 569.9μmolO2/g.

  9. Antioxidant Cerium Oxide Nanoparticles in Biology and Medicine.

    Science.gov (United States)

    Nelson, Bryant C; Johnson, Monique E; Walker, Marlon L; Riley, Kathryn R; Sims, Christopher M

    2016-01-01

    Previously, catalytic cerium oxide nanoparticles (CNPs, nanoceria, CeO2-x NPs) have been widely utilized for chemical mechanical planarization in the semiconductor industry and for reducing harmful emissions and improving fuel combustion efficiency in the automobile industry. Researchers are now harnessing the catalytic repertoire of CNPs to develop potential new treatment modalities for both oxidative- and nitrosative-stress induced disorders and diseases. In order to reach the point where our experimental understanding of the antioxidant activity of CNPs can be translated into useful therapeutics in the clinic, it is necessary to evaluate the most current evidence that supports CNP antioxidant activity in biological systems. Accordingly, the aims of this review are three-fold: (1) To describe the putative reaction mechanisms and physicochemical surface properties that enable CNPs to both scavenge reactive oxygen species (ROS) and to act as antioxidant enzyme-like mimetics in solution; (2) To provide an overview, with commentary, regarding the most robust design and synthesis pathways for preparing CNPs with catalytic antioxidant activity; (3) To provide the reader with the most up-to-date in vitro and in vivo experimental evidence supporting the ROS-scavenging potential of CNPs in biology and medicine. PMID:27196936

  10. Antioxidant Cerium Oxide Nanoparticles in Biology and Medicine

    Directory of Open Access Journals (Sweden)

    Bryant C. Nelson

    2016-05-01

    Full Text Available Previously, catalytic cerium oxide nanoparticles (CNPs, nanoceria, CeO2-x NPs have been widely utilized for chemical mechanical planarization in the semiconductor industry and for reducing harmful emissions and improving fuel combustion efficiency in the automobile industry. Researchers are now harnessing the catalytic repertoire of CNPs to develop potential new treatment modalities for both oxidative- and nitrosative-stress induced disorders and diseases. In order to reach the point where our experimental understanding of the antioxidant activity of CNPs can be translated into useful therapeutics in the clinic, it is necessary to evaluate the most current evidence that supports CNP antioxidant activity in biological systems. Accordingly, the aims of this review are three-fold: (1 To describe the putative reaction mechanisms and physicochemical surface properties that enable CNPs to both scavenge reactive oxygen species (ROS and to act as antioxidant enzyme-like mimetics in solution; (2 To provide an overview, with commentary, regarding the most robust design and synthesis pathways for preparing CNPs with catalytic antioxidant activity; (3 To provide the reader with the most up-to-date in vitro and in vivo experimental evidence supporting the ROS-scavenging potential of CNPs in biology and medicine.

  11. Catalytic properties and biomedical applications of cerium oxide nanoparticles

    KAUST Repository

    Walkey, Carl D.

    2014-11-10

    Cerium oxide nanoparticles (nanoceria) have shown promise as catalytic antioxidants in the test tube, cell culture models and animal models of disease. However given the reactivity that is well established at the surface of these nanoparticles, the biological utilization of nanoceria as a therapeutic still poses many challenges. Moreover the form that these particles take in a biological environment, such as the changes that can occur due to a protein corona, are not well established. This review aims to summarize the existing literature on biological use of nanoceria, and to raise questions about what further study is needed to apply this interesting catalytic material to biomedical applications. These questions include: 1) How does preparation, exposure dose, route and experimental model influence the reported effects of nanoceria in animal studies? 2) What are the considerations to develop nanoceria as a therapeutic agent in regards to these parameters? 3) What biological targets of reactive oxygen species (ROS) and reactive nitrogen species (RNS) are relevant to this targeting, and how do these properties also influence the safety of these nanomaterials?

  12. Antioxidant Cerium Oxide Nanoparticles in Biology and Medicine

    Science.gov (United States)

    Nelson, Bryant C.; Johnson, Monique E.; Walker, Marlon L.; Riley, Kathryn R.; Sims, Christopher M.

    2016-01-01

    Previously, catalytic cerium oxide nanoparticles (CNPs, nanoceria, CeO2-x NPs) have been widely utilized for chemical mechanical planarization in the semiconductor industry and for reducing harmful emissions and improving fuel combustion efficiency in the automobile industry. Researchers are now harnessing the catalytic repertoire of CNPs to develop potential new treatment modalities for both oxidative- and nitrosative-stress induced disorders and diseases. In order to reach the point where our experimental understanding of the antioxidant activity of CNPs can be translated into useful therapeutics in the clinic, it is necessary to evaluate the most current evidence that supports CNP antioxidant activity in biological systems. Accordingly, the aims of this review are three-fold: (1) To describe the putative reaction mechanisms and physicochemical surface properties that enable CNPs to both scavenge reactive oxygen species (ROS) and to act as antioxidant enzyme-like mimetics in solution; (2) To provide an overview, with commentary, regarding the most robust design and synthesis pathways for preparing CNPs with catalytic antioxidant activity; (3) To provide the reader with the most up-to-date in vitro and in vivo experimental evidence supporting the ROS-scavenging potential of CNPs in biology and medicine. PMID:27196936

  13. Cerium toxicity, uptake and translocation in Arabidopsis thaliana seedlings

    Institute of Scientific and Technical Information of China (English)

    WANG Xue; LIN Yousheng; LIU Dongwu; XU Hengjian; LIU Tao; ZHAO Fengyun

    2012-01-01

    Arabidopsis thaliana seedlings were cultivated in 0-500 μmol/L of extraneous cerium (Ce) for 7 d to investigate the toxicity,uptake and translocation of rare earth elements (REEs).The results showed that Ce could be largely absorbed by the roots of A.thaliana and translocated to the shoots.But the uptake rates of Ce by the roots were much higher than the translocation rates from roots to shoots.Ultrastructural analysis revealed that Ce was mainly distributed on the cell wall.At higher concentration,Ce could also enter cell,destroy the ultrastructure of cells and disturb the intrinsic balance of nutrient elements of A.thaliana.Addition of Ce (50-500 μmol/L) to the culture medium significantly inhibited the elongation of primary roots,decreased chlorophyll content,rosette diameter and fresh mass of plants.The damage increased with the increase of Ce concentration in culture medium,although primary root elongation,chlorophyll content,and rosette diameter were stimulated by relatively low concentration (0.5 μmol/L) of Ce.Thus,it is speculated that REEs may become a new type contamination if we don't well control the release of REEs into the environment.

  14. Toenail cerium levels and risk of a first acute myocardial infarction: The EURAMIC and heavy metals study

    NARCIS (Netherlands)

    Gomez-Aracena, J.; Riemersma, R.A.; Veer, van 't P.; Kok, F.J.

    2006-01-01

    The association between cerium status and risk of first acute myocardial infarction (AMI) was examined in a case-control study in 10 centres from Europe and Israel. Cerium in toenails was assessed by neutron activation analysis in 684 cases and 724 controls aged 70years or younger. Mean concentratio

  15. The development of 126Sn separation procedure by means of TBP resin

    International Nuclear Information System (INIS)

    Separation possibilities of 126Sn with a new extraction-chromatographic material TBP Resin were studied. Suitable conditions for tin separation were determined in hydrochloric acid medium. 126Sn was concentrated on TBP resin from 6 mol L-1 HCl and was eluted with 0.1 mol L-1 HCl. A purification step to remove 137Cs with AMP-PAN column was necessary to obtain sufficiently purified samples which were directly measured with gamma spectrometry for 126Sn activity. Separation of 126Sn from a raw sludge sample was done according to proposed procedure, 126Sn was detected and its activity was determined. (author)

  16. Morphology Controlling of the Ultrafine Cerium Dioxide (CeO2) Precursor

    Institute of Scientific and Technical Information of China (English)

    Jianqing CHEN; Zhigang CHEN; Jinchun LI

    2004-01-01

    The synthesis of ultrafine cerium dioxide precursor via homogeneous precipitation was studied. Mixed aqueous solution of anhydrous cerium nitrate and urea was first heated to 85℃ for 2 h, and the prepared suspension was then aged at room temperature for various periods of time. White precipitate was finally collected by centrifuging and washed with distilled water and anhydrous ethanol. The obtained cerium dioxide (CeO2) precursor was observed with SEM. It was found that the morphology and size of the precursor were strongly affected by aging time and stirring conditions (with or without stirring).The precipitated fine spherical particles of the precursor changed their shape from ellipse to slice or directly to slice. Fine spherical monodispersed (300 nm) precursor powders could be obtained by controlling the aging time. Stirring the solution also could change the reaction process and thus the morphology and size of the precursor were changed.

  17. Mesoporous cerium oxide nanospheres for the visible-light driven photocatalytic degradation of dyes

    Directory of Open Access Journals (Sweden)

    Subas K. Muduli

    2014-04-01

    Full Text Available A facile, solvothermal synthesis of mesoporous cerium oxide nanospheres is reported for the purpose of the photocatalytic degradation of organic dyes and future applications in sustainable energy research. The earth-abundant, relatively affordable, mixed valence cerium oxide sample, which consists of predominantly Ce7O12, has been characterized by powder X-ray diffraction, X-ray photoelectron and UV–vis spectroscopy, and transmission electron microscopy. Together with N2 sorption experiments, the data confirms that the new cerium oxide material is mesoporous and absorbs visible light. The photocatalytic degradation of rhodamin B is investigated with a series of radical scavengers, suggesting that the mechanism of photocatalytic activity under visible-light irradiation involves predominantly hydroxyl radicals as the active species.

  18. Fabrication of Cerium Oxide and Uranium Oxide Microspheres for Space Nuclear Power Applications

    Energy Technology Data Exchange (ETDEWEB)

    Jeffrey A. Katalenich; Michael R. Hartman; Robert C. O' Brien

    2013-02-01

    Cerium oxide and uranium oxide microspheres are being produced via an internal gelation sol-gel method to investigate alternative fabrication routes for space nuclear fuels. Depleted uranium and non-radioactive cerium are being utilized as surrogates for plutonium-238 (Pu-238) used in radioisotope thermoelectric generators and for enriched uranium required by nuclear thermal rockets. While current methods used to produce Pu-238 fuels at Los Alamos National Laboratory (LANL) involve the generation of fine powders that pose a respiratory hazard and have a propensity to contaminate glove boxes, the sol-gel route allows for the generation of oxide microsphere fuels through an aqueous route. The sol-gel method does not generate fine powders and may require fewer processing steps than the LANL method with less operator handling. High-quality cerium dioxide microspheres have been fabricated in the desired size range and equipment is being prepared to establish a uranium dioxide microsphere production capability.

  19. Magnetic ordering in the static intermediate-valent cerium compound Ce2RuZn4

    Science.gov (United States)

    Eyert, Volker; Scheidt, Ernst-Wilhelm; Scherer, Wolfgang; Hermes, Wilfried; Pöttgen, Rainer

    2008-12-01

    The low-temperature behavior of Ce2RuZn4 has been investigated. Specific-heat and magnetic-susceptibility data reveal an antiferromagnetic transition at a Néel temperature of 2 K. Ce2RuZn4 is a static intermediate-valent compound with two crystallographically independent cerium atoms. The magnetic data clearly show that only one cerium site is magnetic (Ce3+) , while the second one carries no magnetic moment. The experimental data are interpreted with the help of first-principles electronic structure calculations using density-functional theory and the augmented spherical wave method. The calculations reveal the occurrence of two different cerium sites, which are characterized by strongly localized magnetic moments and strong Ce-Ru bonding.

  20. Green synthesized cerium oxide nanoparticle: A prospective drug against oxidative harm.

    Science.gov (United States)

    Dutta, Debanjan; Mukherjee, Riya; Patra, Mousumi; Banik, Milon; Dasgupta, Rakhi; Mukherjee, Manabendra; Basu, Tarakdas

    2016-11-01

    Cerium oxide nanoparticle (CeONP) of size 2-3nm was synthesized by a new, simple and green method at ambient temperature, using cerium nitrate as prime precursor and Aloe vera leaf extract as stabilizing agent. Of the two oxidation states (+3) and (+4) of cerium, it was dominantly present in (+3) state in CeONP and cyclic conversion of Ce(III)O→Ce(IV)O→Ce(III)O by reaction with H2O2 implied uninterrupted antioxidant property of CeONP. Moreover, the higher oxygen defect in the crystal lattice produced particles with higher antioxidant activity. CeONP was found to neutralize the deleterious effects of H2O2 viz., cell death, generation of intracellular reactive oxygen species and loss of connectivity in mouse neural cells. Therefore, CeONP might have potential use in future as an anti-oxidant drug. PMID:27478962

  1. Oxochloroalkoxide of the Cerium (IV and Titanium (IV as oxides precursor

    Directory of Open Access Journals (Sweden)

    Machado Luiz Carlos

    2002-01-01

    Full Text Available The Cerium (IV and Titanium (IV oxides mixture (CeO2-3TiO2 was prepared by thermal treatment of the oxochloroisopropoxide of Cerium (IV and Titanium (IV. The chemical route utilizing the Cerium (III chloride alcoholic complex and Titanium (IV isopropoxide is presented. The compound Ce5Ti15Cl16O30 (iOPr4(OH-Et15 was characterized by elemental analysis, FTIR and TG/DTG. The X-ray diffraction patterns of the oxides resulting from the thermal decomposition of the precursor at 1000 degreesC for 36 h indicated the formation of cubic cerianite (a = 5.417Å and tetragonal rutile (a = 4.592Å and (c = 2.962 Å, with apparent crystallite sizes around 38 and 55nm, respectively.

  2. Cathodic electrolysis method of depositing cerium conversion films on industrial pure aluminum

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Two two-step techniques, called TS2/TS7 and TS3/TS7, respectively, have been developed to form cerium conversion films on the surface of industrial pure aluminum. The tested material was cathodically electrolyzed in the alkaline solution containing cerium salt, and uniform films containing cerium were obtained after the two-step treatment. It is found that the films obtained by TS2/TS7 and TS3/TS7 techniques are about 4.0 and 3.0 m in thickness, respectively. The material has better corrosion resistance in the chloride solution after the two-step electrolysis treatment compared with the one-step treated and naked specimens.

  3. Effect of Impurities and Cerium on Stress Concentration Sensitivity of Al-Li Based Alloys

    Institute of Scientific and Technical Information of China (English)

    孟亮; 田丽

    2002-01-01

    A notch sensitivity factor was derived in order to evaluate the stress concentration sensitivity of Al-Li based alloys. The factor values for the Al-Li alloy sheets containing various contents of impurities and cerium addition were evaluated by determining the mechanical properties. It is found that the impurities Fe, Si, Na and K significantly enhance the stress concentration sensitivity of the alloys 2090 and 8090, whereas cerium addition reduces the stress concentration sensitivity to a certain degree for the high strength alloys. However, an excess amount of cerium addition in the high ductility alloy 1420 can significantly increase the stress concentration sensitivity. As compared with conventional aluminum alloys, the Al-Li based alloys generally show high stress concentration sensitivity. Therefore, a special attention must be paid to this problem in the practical application of Al-Li based alloys.

  4. Study of phase transitions in cerium in shock-wave experiments

    Directory of Open Access Journals (Sweden)

    Zhernokletov M.V.

    2015-01-01

    Full Text Available Cerium has a complex phase diagram that is explained by the presence of structure phase transitions. Planar gauges were used in various combinations in experiments for determination of sound velocity dependence on pressure in cerium by the technique of PVDF gauge. The data of time dependence on pressure profiles with use of x(t diagrams and the D(u relation for cerium allowed the definition of the Lagrangian velocity of the unloading wave CLagr and the Eulerian velocity CEul by taking into account the compression σ. These results accords with data obtained by using the technique of VISAR and a manganin-based gauge, and calculated pressure dependence of isentropic sound velocity according to the VNIITF EOS. Metallography analysis of post-experimental samples did not find any changes in a phase composition.

  5. Catalytic spectrophotometric determination of cerium by ion exchange separation coupled to a flow injection system

    International Nuclear Information System (INIS)

    A flow injection method is described intended for the determination of cerium based on its catalytic effect on the oxidation of gallocyanine by peroxydisulfate in acidic media. The proposed flow injection manifold incorporates a ion exchange separation system in the carrier stream. The decolorisation of gallocyanine due to its oxidation was used to monitor the reaction by spectrophotometry at 524 nm. The variables which affected the reaction rate were fully investigated. By this method cerium(4) can be determined in the range of 0.30-10.0 μg with a limit of detection of 0.25 μg. The relative standard deviation for ten replicate determinations of 1.0 μg of cerium(4) was 1.8 %

  6. Excitation induced spectroscopic study and quenching effect in cerium samarium codoped lithium aluminoborate glasses

    Science.gov (United States)

    Kaur, Parvinder; Kaur, Simranpreet; Singh, Gurinder Pal; Arora, Deepawali; Kumar, Sunil; Singh, D. P.

    2016-08-01

    Lithium aluminium borate host has been codoped with cerium and samarium to prepare glass by conventional melt quench technique. Their structural and spectroscopic investigation has been carried out using XRD, FTIR and density measurements. The UV-Vis absorption spectra and fluorescence spectra (λexc.=380 nm and 400 nm) have been studied for spectroscopic analysis. The amorphous nature of the prepared samples is shown by XRD. The density is increasing with addition of cerium at the expense of aluminium, keeping other components constant. FTIR study also shows the presence of compact and stable tetrahedral BO4 units thus supporting the density results. The UV- Vis absorption spectra show a shift of optical absorption edge towards longer wavelength along with an increase in intensity of peaks with rising samarium concentration. The fluorescence spectra show a blue shift and subsequent suppression of cerium peaks with addition of samarium.

  7. Exposure of cerium oxide nanoparticles to kidney bean shows disturbance in the plant defense mechanisms

    International Nuclear Information System (INIS)

    Graphical abstract: - Highlights: • Kidney bean roots uptake nCeO2 primarily without biotransformation. • Cerium reached the root vascular tissues through gaps in the Casparian strip. • On longer exposure to high concentration, roots demonstrate stress response. • In leaves, guaiacol peroxidase plays a major role in ROS scavenging. - Abstract: Overwhelming use of engineered nanoparticles demands rapid assessment of their environmental impacts. The transport of cerium oxide nanoparticles (nCeO2) in plants and their impact on cellular homeostasis as a function of exposure duration is not well understood. In this study, kidney bean plants were exposed to suspensions of ∼8 ± 1 nm nCeO2 (62.5 to 500 mg/L) for 15 days in hydroponic conditions. Plant parts were analyzed for cerium accumulation after one, seven, and 15 days of nCeO2 exposure. The primary indicators of stress like lipid peroxidation, antioxidant enzyme activities, total soluble protein and chlorophyll contents were studied. Cerium in tissues was localized using scanning electron microscopy and synchrotron μ-XRF mapping, and the chemical forms were identified using μ-XANES. In the root epidermis, cerium was primarily shown to exist as nCeO2, although a small fraction (12%) was biotransformed to Ce(III) compound. Cerium was found to reach the root vascular tissues and translocate to aerial parts with time. Upon prolonged exposure to 500 mg nCeO2/L, the root antioxidant enzyme activities were significantly reduced, simultaneously increasing the root soluble protein by 204%. In addition, leaf's guaiacol peroxidase activity was enhanced with nCeO2 exposure in order to maintain cellular homeostasis

  8. Exposure of cerium oxide nanoparticles to kidney bean shows disturbance in the plant defense mechanisms

    Energy Technology Data Exchange (ETDEWEB)

    Majumdar, Sanghamitra [Department of Chemistry, The University of Texas at El Paso, 500 West University Ave., El Paso, TX 79968 (United States); University of California Center for Environmental Implications of Nanotechnology (UC CEIN) (United States); Peralta-Videa, Jose R. [Department of Chemistry, The University of Texas at El Paso, 500 West University Ave., El Paso, TX 79968 (United States); Environmental Science and Engineering PhD Program, The University of Texas at El Paso, 500 West University Ave., El Paso, TX 79968 (United States); University of California Center for Environmental Implications of Nanotechnology (UC CEIN) (United States); Bandyopadhyay, Susmita [Environmental Science and Engineering PhD Program, The University of Texas at El Paso, 500 West University Ave., El Paso, TX 79968 (United States); University of California Center for Environmental Implications of Nanotechnology (UC CEIN) (United States); Castillo-Michel, Hiram [European Synchrotron Radiation Facility, B.P. 220-38043 Grenoble, Cedex (France); Hernandez-Viezcas, Jose-Angel [Department of Chemistry, The University of Texas at El Paso, 500 West University Ave., El Paso, TX 79968 (United States); University of California Center for Environmental Implications of Nanotechnology (UC CEIN) (United States); Sahi, Shivendra [Department of Biology, Western Kentucky University, Bowling Green, KY 42101 (United States); Gardea-Torresdey, Jorge L., E-mail: jgardea@utep.edu [Department of Chemistry, The University of Texas at El Paso, 500 West University Ave., El Paso, TX 79968 (United States); Environmental Science and Engineering PhD Program, The University of Texas at El Paso, 500 West University Ave., El Paso, TX 79968 (United States); University of California Center for Environmental Implications of Nanotechnology (UC CEIN) (United States)

    2014-08-15

    Graphical abstract: - Highlights: • Kidney bean roots uptake nCeO{sub 2} primarily without biotransformation. • Cerium reached the root vascular tissues through gaps in the Casparian strip. • On longer exposure to high concentration, roots demonstrate stress response. • In leaves, guaiacol peroxidase plays a major role in ROS scavenging. - Abstract: Overwhelming use of engineered nanoparticles demands rapid assessment of their environmental impacts. The transport of cerium oxide nanoparticles (nCeO{sub 2}) in plants and their impact on cellular homeostasis as a function of exposure duration is not well understood. In this study, kidney bean plants were exposed to suspensions of ∼8 ± 1 nm nCeO{sub 2} (62.5 to 500 mg/L) for 15 days in hydroponic conditions. Plant parts were analyzed for cerium accumulation after one, seven, and 15 days of nCeO{sub 2} exposure. The primary indicators of stress like lipid peroxidation, antioxidant enzyme activities, total soluble protein and chlorophyll contents were studied. Cerium in tissues was localized using scanning electron microscopy and synchrotron μ-XRF mapping, and the chemical forms were identified using μ-XANES. In the root epidermis, cerium was primarily shown to exist as nCeO{sub 2}, although a small fraction (12%) was biotransformed to Ce(III) compound. Cerium was found to reach the root vascular tissues and translocate to aerial parts with time. Upon prolonged exposure to 500 mg nCeO{sub 2}/L, the root antioxidant enzyme activities were significantly reduced, simultaneously increasing the root soluble protein by 204%. In addition, leaf's guaiacol peroxidase activity was enhanced with nCeO{sub 2} exposure in order to maintain cellular homeostasis.

  9. The Role of Circulating MicroRNA-126 (miR-126: A Novel Biomarker for Screening Prediabetes and Newly Diagnosed Type 2 Diabetes Mellitus

    Directory of Open Access Journals (Sweden)

    Yang Liu

    2014-06-01

    Full Text Available Recent studies suggested an association of endothelial microRNA-126 (miR-126 with type 2 diabetes mellitus (T2DM. In the current study, we examined whether circulating miR-126 is associated with T2DM and pre-diabetic syndrome. The study included 82 subjects with impaired glucose tolerance (IGT, 75 subjects with impaired fasting glucose (IFG, 160 patients with newly diagnosed T2DM, and 138 healthy individuals. Quantitative polymerase chain reaction (qPCR was used to examine serum miR-126. Serum miR-126 was significantly lower in IGT/IFG subjects and T2DM patients than in healthy controls (p < 0.05. After six months of treatment (diet control and exercise in IGT/IFG subjects, insulin plus diet control and exercise in T2DM patients, serum miR-126 increased significantly (p < 0.05. An analysis based on serum miR-126 in the sample revealed a significantly higher odds ratio (OR for the subjects with the lowest 1/3 of serum miR-126 for T2DM (OR: 3.500, 95% confidence interval: 1.901–6.445, p < 0.05 than subjects within the highest 1/3 of serum miR-126. Such an association was still apparent after adjusting for other major risk factors. The area under the curve (AUC for the receiver-operating characteristic (ROC analysis was 0.792 (95% confidence interval: 0.707–0.877, p < 0.001. These results encourage the use of serum miR-126 as a biomarker for pre-diabetes and diabetes mellitus, as well as therapeutic response.

  10. METHOD OF SEPARATING TETRAVALENT PLUTONIUM VALUES FROM CERIUM SUB-GROUP RARE EARTH VALUES

    Science.gov (United States)

    Duffield, R.B.; Stoughton, R.W.

    1959-02-01

    A method is presented for separating plutonium from the cerium sub-group of rare earths when both are present in an aqueous solution. The method consists in adding an excess of alkali metal carbonate to the solution, which causes the formation of a soluble plutonium carbonate precipitate and at the same time forms an insoluble cerium-group rare earth carbonate. The pH value must be adjusted to bctween 5.5 and 7.5, and prior to the precipitation step the plutonium must be reduced to the tetravalent state since only tetravalent plutonium will form the soluble carbonate complex.

  11. Feasibility of Substituting Cerium-Rich Metal by La-Pr-Ce Alloy in Magnesium Alloy

    Institute of Scientific and Technical Information of China (English)

    伏思静; 赵平

    2004-01-01

    In magnesium alloy ZM3, using cheap Lanthanum-praseodymium-cerium (LPC) rare earth as a substitute for rich-cerium rare earth was studied. The experimental results show that when the adding amount of LPC is between 2.53% and 3.33%, the tensile strength increases as the adding amount of LPC increases; when the amount of RE is 2.53% and 3.33%, the average tensile strength is 142.35, 153.65 MPa respectively. The results show that LPC rare earth replacing rich Ce rare earth is feasible for the tensile strength of ZM3.

  12. Dissociation of outer membrane for Escherichia coli cell caused by cerium nitrate

    Institute of Scientific and Technical Information of China (English)

    陈爱美; 施庆珊; 冯劲; 欧阳友生; 陈仪本; 谭绍早

    2010-01-01

    The biological effect of cerium nitrate on the outer membrane(OM) of Escherichia coli(E.coli) cell was studied,and the antim-icrobial mechanism of rare earth elements was explored.The antimicrobial effect of cerium nitrate on E.coli cell was valued by plate count method,and the morphology change of E.coli cell was observed with scanning electron microscopy(SEM) and transmission electron microscopy(TEM).The results showed that the E.coli cell suspension was flocculated when the concentration of Ce(NO3)3?6H2O...

  13. Synthesis and characterization of two dimensional metal organic framework of cerium with tetraaza macrocyclic

    Energy Technology Data Exchange (ETDEWEB)

    Bt Safiin, Nurul Atikah; Yarmo, Ambar; Yamin, Bohari M. [School of Chemical Science and Food Technology. Faculty Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor Darul Ehsan (Malaysia)

    2013-11-27

    A two dimensional metal organic framework containing cerium sufate layers and ethylenediaminium between layers was obtained by refluxing the mixture of cerium sulphate and 5,5,7,12,12,14-hexamethyl-1,4,8,11-tetraazacyclotetradeca-7, 14-diene bromide. The complex was characterized by infrared spectroscopy and microelemental analysis. X-ray study showed that the complex adopts eleven coordination environments about the central atom. Thermogravimetric study showed the removal of water molecules at about 70°C followed by a gradual mass loss until the whole structure collapsed at about 400°C.

  14. Photocatalytic action of cerium molybdate and iron-titanium oxide hollow nanospheres on Escherichia coli

    International Nuclear Information System (INIS)

    This study is focused on the production of hollow nanospheres that reveal antibacterial action. Cerium molybdate and iron-titanium oxide hollow nanospheres with a diameter of 175 ± 15 and 221 ± 10 nm, respectively, were synthesized using emulsion polymerization and the sol–gel process. Their morphology characterization was accomplished using scanning electron microscopy. Their antibacterial action was examined on pure culture of Escherichia coli considering the loss of their viability. Both hollow nanospheres presented photocatalytic action after illumination with blue–black light, but those of cerium molybdate also demonstrated photocatalytic action in the dark. Therefore, the produced nanospheres can be used for antibacterial applications.

  15. A corrosion resistant cerium oxide based coating on aluminum alloy 2024 prepared by brush plating

    Energy Technology Data Exchange (ETDEWEB)

    Tang Junlei; Han Zhongzhi [School of Materials Science and Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); Zuo Yu, E-mail: zuoy@mail.buct.edu.cn [School of Materials Science and Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); Tang Yuming [School of Materials Science and Engineering, Beijing University of Chemical Technology, Beijing 100029 (China)

    2011-01-15

    Cerium oxide based coatings were prepared on AA2024 Al alloy by brush plating. The characteristic of this technology is that hydrogen peroxide, which usually causes the plating solution to be unstable, is not necessary in the plating electrolyte. The coating showed laminated structures and good adhesive strength with the substrate. X-ray diffraction and X-ray photoelectron spectroscopy analysis showed that the coatings were composed of Ce(III) and Ce(IV) oxides. The brush plated coatings on Al alloys improved corrosion resistance. The influence of plating parameters on structure and corrosion resistance of the cerium oxide based coating was studied.

  16. [Laser resonance ionization spectroscopy of even-parity autoionization states of cerium atom].

    Science.gov (United States)

    Li, Zhi-ming; Zhu, Feng-rong; Zhang, Zi-bin; Ren, Xiang-jun; Deng, Hu; Zhai, Li-hua; Zhang, Li-xing

    2004-12-01

    This paper describes the investigation of even-parity autoionization states of cerium atoms by three-step three-color resonance ionization spectroscopy (RIS). Twenty-seven odd-parity highly excited levels, whose transition probability is high, were used in this research. One hundred and forty-one autoionization states were found by these channels with the third-step laser scanning in the wavelength range of 634-670 nm. The ionization probabilities of different channels, which had higher cross sections, were compared. On the basis of this, eight optimal photoionization schemes of cerium atom have been given. PMID:15828309

  17. Comparative Study of Magnetic Instabilities in Cerium Compounds

    International Nuclear Information System (INIS)

    The variety of new phases and physical phenomena discovered in intermetallic compounds containing Rare Earths or Actinides has motivated, during the last four decades, the sustained study of their magnetic phase diagrams.The current interest is focused on the investigation of the region of the phase diagram where the magnetic order of Cerium, Ytterbium and Uranium based systems is destabilized.In this region different behaviours have been detected, such as non conventional superconductivity and the anomalous dependencies of the thermal, magnetic and transport properties at very low temperatures, associated to non-Fermi liquid behaviour.A simple model, the Doniach diagram, has guided the interpretation of the destabilization of the magnetic order in the previously mentioned systems.However, most of the systems that have been studied so far cannot be described within this model.This fact has motivated the development of a phenomenological classification of phase diagrams that has been mostly applied to cerium based compounds.This classification defines three types of phase diagrams, that can be distinguished by the way in which the magnetic transition is suppressed when a control parameter (such as doping or pressure) is driven towards its critical value.Within this scenario, we study the suppression of the antiferromagnetic order of the intermetallic compounds CeIn3, CeRh2Si2 and CePd2Al3 as a function of Ce-ligand alloying.The resulting systems, CeIn3-xSnx, Ce(CuxRh1-x)2Si2 and CePd2-xNixAl3, present different crystalline structures and the effects produced by the alloying process are different in each case.We analyse the resulting magnetic phase diagrams, and compare them with the above mentioned phenomenological classification.With such a purpose, we study in detail the region in which the magnetic instability takes place, in the proximity of the respective critical concentrations.Taking into account both our results and those reported in the literature, we

  18. Fate of cerium dioxide nanoparticles in endothelial cells: exocytosis

    International Nuclear Information System (INIS)

    Although cytotoxicity and endocytosis of nanoparticles have been the subject of numerous studies, investigations regarding exocytosis as an important mechanism to reduce intracellular nanoparticle accumulation are rather rare and there is a distinct lack of knowledge. The current study investigated the behavior of human microvascular endothelial cells to exocytose cerium dioxide (CeO2) nanoparticles (18.8 nm) by utilization of specific inhibitors [brefeldin A; nocodazole; methyl-β-cyclodextrin (MβcD)] and different analytical methods (flow cytometry, transmission electron microscopy, inductively coupled plasma mass spectrometry). Overall, it was found that endothelial cells were able to release CeO2 nanoparticles via exocytosis after the migration of nanoparticle containing endosomes toward the plasma membrane. The exocytosis process occurred mainly by fusion of vesicular membranes with plasma membrane resulting in the discharge of vesicular content to extracellular environment. Nevertheless, it seems to be likely that nanoparticles present in the cytosol could leave the cells in a direct manner. MβcD treatment led to the strongest inhibition of the nanoparticle exocytosis indicating a significant role of the plasma membrane cholesterol content in the exocytosis process. Brefeldin A (inhibitor of Golgi-to-cell-surface-transport) caused a higher inhibitory effect on exocytosis than nocodazole (inhibitor of microtubules). Thus, the transfer from distal Golgi compartments to the cell surface influenced the exocytosis process of the CeO2 nanoparticles more than the microtubule-associated transport. In conclusion, endothelial cells, which came in contact with nanoparticles, e.g., after intravenously applied nano-based drugs, can regulate their intracellular nanoparticle amount, which is necessary to avoid adverse nanoparticle effects on cells

  19. Variations in Reactivity on Different Crystallographic Orientations of Cerium Oxide

    Energy Technology Data Exchange (ETDEWEB)

    Mullins, David R [ORNL; Albrecht, Peter M [ORNL; Calaza, Florencia C [ORNL

    2013-01-01

    Cerium oxide is a principal component in many heterogeneous catalytic processes. One of its key characteristics is the ability to provide or remove oxygen in chemical reactions. The different crystallographic faces of ceria present significantly different surface structures and compositions that may alter the catalytic reactivity. The structure and composition determine the number of coordination vacancies surrounding surface atoms, the availability of adsorption sites, the spacing between adsorption sites and the ability to remove O from the surface. To investigate the role of surface orientation on reactivity, CeO2 films were grown with two different orientations. CeO2(100) films were grown ex situ by pulsed laser deposition on Nb-doped SrTiO3(100). CeO2(111) films were grown in situ by thermal deposition of Ce metal onto Ru(0001) in an oxygen atmosphere. The chemical reactivity was characterized by the adsorption and decomposition of various molecules such as alcohols, aldehydes and organic acids. In general the CeO2(100) surface was found to be more active, i.e. molecules adsorbed more readily and reacted to form new products, especially on a fully oxidized substrate. However the CeO2(100) surface was less selective with a greater propensity to produce CO, CO2 and water as products. The differences in chemical reactivity are discussed in light of possible structural terminations of the two surfaces. Recently nanocubes and nano-octahedra have been synthesized that display CeO2(100) and CeO2(111) faces, respectively. These nanoparticles enable us to correlate reactions on high surface area model catalysts at atmospheric pressure with model single crystal films in a UHV environment.

  20. Thermoluminescence of cerium and terbium -doped calcium pyrophosphate

    Energy Technology Data Exchange (ETDEWEB)

    Roman L, J.; Cruz Z, E. [UNAM, Instituto de Ciencias Nucleares, Circuito Exterior, Ciudad Universitaria, 04510 Mexico D. F. (Mexico); Lozano R, I. B.; Diaz G, J. A. I., E-mail: jesus.roman@nucleares.unam.mx [IPN, Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada, Av. Legaria No. 694, 11500 Mexico D. F. (Mexico)

    2015-10-15

    The aim of this work is to report the thermoluminescence (Tl) response of Calcium Pyrophosphate phosphor doped with Cerium and Terbium impurities (Ca{sub 2}P{sub 2}O{sub 7}:Ce{sup 3+},Tb{sup 3+}). The phosphors were synthesized using the co-precipitation method and annealed at 900 degrees C by two hours for obtain the β phase. The intentional doping with Ce and Tb ions was 1 at.% and 0.1 at.%, whereas in the EDS results the concentration of impurities was 0.39 at.% and 0.05 at.%, respectively. The superficial morphology of phosphor is mainly composed by thin wafers of different size. All samples were exposed to gamma rays from {sup 60}Co in the Gammacell-200 irradiator. The Tl response of the phosphor was measured from Rt up to 350 degrees C and under nitrogen atmosphere in a Harshaw TLD 3500 reader. The glow curves of the Ca{sub 2}P{sub 2}O{sub 7}:Ce{sup 3+},Tb{sup 3+} powders showed a broad intense Tl peak centered at 165 degrees C and a shoulder at approximate 260 degrees C was observed. A linear Tl response in the range of absorbed dose of 0.2 to 10 Gy was obtained. Tl glow curves were analyzed using the initial rise (IR)and computerized glow curve deconvolution methods to evaluate the kinetics parameters such as activation energy (E), frequency factor (s) and kinetic order (b). (Author)

  1. Fate of cerium dioxide nanoparticles in endothelial cells: exocytosis

    Energy Technology Data Exchange (ETDEWEB)

    Strobel, Claudia, E-mail: Claudia.Strobel@med.uni-jena.de [Jena University Hospital – Friedrich Schiller University Jena, Department of Experimental Radiology, Institute of Diagnostic and Interventional Radiology (Germany); Oehring, Hartmut [Jena University Hospital – Friedrich Schiller University Jena, Institute of Anatomy II (Germany); Herrmann, Rudolf [University of Augsburg, Department of Physics (Germany); Förster, Martin [Jena University Hospital – Friedrich Schiller University Jena, Department of Internal Medicine I, Division of Pulmonary Medicine and Allergy/Immunology (Germany); Reller, Armin [University of Augsburg, Department of Physics (Germany); Hilger, Ingrid, E-mail: ingrid.hilger@med.uni-jena.de [Jena University Hospital – Friedrich Schiller University Jena, Department of Experimental Radiology, Institute of Diagnostic and Interventional Radiology (Germany)

    2015-05-15

    Although cytotoxicity and endocytosis of nanoparticles have been the subject of numerous studies, investigations regarding exocytosis as an important mechanism to reduce intracellular nanoparticle accumulation are rather rare and there is a distinct lack of knowledge. The current study investigated the behavior of human microvascular endothelial cells to exocytose cerium dioxide (CeO{sub 2}) nanoparticles (18.8 nm) by utilization of specific inhibitors [brefeldin A; nocodazole; methyl-β-cyclodextrin (MβcD)] and different analytical methods (flow cytometry, transmission electron microscopy, inductively coupled plasma mass spectrometry). Overall, it was found that endothelial cells were able to release CeO{sub 2} nanoparticles via exocytosis after the migration of nanoparticle containing endosomes toward the plasma membrane. The exocytosis process occurred mainly by fusion of vesicular membranes with plasma membrane resulting in the discharge of vesicular content to extracellular environment. Nevertheless, it seems to be likely that nanoparticles present in the cytosol could leave the cells in a direct manner. MβcD treatment led to the strongest inhibition of the nanoparticle exocytosis indicating a significant role of the plasma membrane cholesterol content in the exocytosis process. Brefeldin A (inhibitor of Golgi-to-cell-surface-transport) caused a higher inhibitory effect on exocytosis than nocodazole (inhibitor of microtubules). Thus, the transfer from distal Golgi compartments to the cell surface influenced the exocytosis process of the CeO{sub 2} nanoparticles more than the microtubule-associated transport. In conclusion, endothelial cells, which came in contact with nanoparticles, e.g., after intravenously applied nano-based drugs, can regulate their intracellular nanoparticle amount, which is necessary to avoid adverse nanoparticle effects on cells.

  2. Prognostic value of microRNA-126 and CRK expression in gastric cancer

    Science.gov (United States)

    Yue, Shun; Shi, Huichang; Han, Jun; Zhang, Tiecheng; Zhu, Weiguo; Zhang, Dahong

    2016-01-01

    Background MicroRNA (miR)-126, acting as a tumor suppressor, has been reported to inhibit the invasion of gastric cancer cells in part by targeting v-crk sarcoma virus CT10 oncogene homologue (CRK). The aim of this study was to investigate the clinical significance of miR-126/CRK axis in gastric cancer. Methods miR-126 and CRK mRNA expression levels were detected by real-time quantitative reverse transcription polymerase chain reaction in 220 self-pairs of gastric cancer and adjacent noncancerous tissues. Results Expression levels of miR-126 and CRK mRNA in gastric cancer tissues were, respectively, lower and higher than those in adjacent noncancerous tissues (both P<0.001). Low miR-126 expression and high CRK expression, alone or in combination, were all significantly associated with positive lymph node and distant metastases and advanced TNM stage of human gastric cancer (all P<0.05). We also found that the overall survival rates of the patients with low miR-126 expression and high CRK expression were, respectively, shorter than those with high miR-126 expression and low CRK expression. Interestingly, miR-126-low/CRK-high expression was associated with a significantly worse overall survival of all miR-126/CRK groups (P<0.001). Moreover, multivariate analysis identified miR-126 and/or CRK expression as independent prognostic factors for patients with gastric cancer. Notably, the prognostic relevance of miR-126 and/or CRK expression was more obvious in the subgroup of patients with TNM stage IV. Conclusion Dysregulation of miR-126/CRK axis may promote the malignant progression of human gastric cancer. miR-126 and CRK combined expression may serve as an independent predictor of overall survival in patients with advanced gastric cancer.

  3. Cerium Oxide Nanoparticles and Bulk Cerium Oxide Leading to Different Physiological and Biochemical Responses in Brassica rapa.

    Science.gov (United States)

    Ma, Xingmao; Wang, Qiang; Rossi, Lorenzo; Zhang, Weilan

    2016-07-01

    Cerium oxide nanoparticles (CeO2NPs) have been incorporated into many commercial products, and their potential release into the environment through the use and disposal of these products has caused serious concerns. Despite the previous efforts and rapid progress on elucidating the environmental impact of CeO2NPs, the long-term impact of CeO2NPs to plants, a key component of the ecosystem, is still not well understood. The potentially different impact of CeO2NPs and their bulk counterparts to plants is also unclear. The main objectives of this study were (1) to investigate whether continued irrigation with solutions containing different concentrations of CeO2NPs (0, 10, and 100 mg/L) would induce physiological and biochemical adjustments in Brassica rapa in soil growing conditions and (2) to determine whether CeO2NPs and bulk CeO2 particles exert different impacts on plants. The results indicated that bulk CeO2 at 10 and 100 mg/L enhanced plant biomass by 28% and 35%, respectively, while CeO2NPs at equivalent concentrations did not. While the bulk CeO2 treatment resulted in significantly higher concentrations of hydrogen peroxide (H2O2) in plant tissues at the vegetative stage, CeO2NPs led to significantly higher H2O2 levels in plant tissues at the floral stage. The activity of superoxide dismutase (SOD) in Brassica rapa also displayed a growth-stage dependent response to different sizes of CeO2 while catalase (CAT) activity was not affected by either size of CeO2 throughout the life cycle of Brassica rapa. Altogether, the results demonstrated that plant responses to CeO2 exposure varied with the particle sizes and the growth stages of plants. PMID:26691446

  4. The effects of cerium doping on the size, morphology, and optical properties of α-hematite nanoparticles for ultraviolet filtration

    International Nuclear Information System (INIS)

    Highlights: • Possible application of cerium-doped α-hematite as ultraviolet filter. • Nanoparticles obtained through co-precipitation technique using various cerium doping levels followed by annealing. • Comprehensive materials characterisation utilizing XRD, DSC/TGA, STEM, UV–vis spectroscopy. • Increasing cerium content reduces particle sizing and alters morphology. • Solubility of cerium in hematite seen between 5 and 10% doping, 10% cerium doping greatly enhances attenuation in ultraviolet region and increases optical bandgap. - Abstract: Metal oxide nanoparticles have potential use in energy storage, electrode materials, as catalysts and in the emerging field of nanomedicine. Being able to accurately tailor the desirable properties of these nanoceramic materials, such as particle size, morphology and optical bandgap (Eg) is integral in the feasibility of their use. In this study we investigate the altering of both the structure and physical properties through the doping of hematite (α-Fe2O3) nanocrystals with cerium at a range of concentrations, synthesised using a one-pot co-precipitation method. This extremely simple synthesis followed by thermal treatment results in stable Fe2−xCexOy nanoceramics resulting from the burning of any unreacted precursors and transformation of goethite-cerium doped nanoparticle intermediate. The inclusion of Ce into the crystal lattice of these α-Fe2O3 nanoparticles causes a significantly large reduction in mean crystalline size and alteration in particle morphology with increasing cerium content. Finally we report an increase optical semiconductor bandgap, along with a substantial increase in the ultraviolet attenuation found for a 10% Ce-doping concentration which shows the potential application of cerium-doped hematite nanocrystals to be used as a pigmented ultraviolet filter for cosmetic products

  5. The effects of cerium doping on the size, morphology, and optical properties of α-hematite nanoparticles for ultraviolet filtration

    Energy Technology Data Exchange (ETDEWEB)

    Cardillo, Dean [Institute for Superconducting and Electronic Materials, AIIM Facility, University of Wollongong Innovation Campus, Squires Way, North Wollongong, NSW 2500 (Australia); Konstantinov, Konstantin, E-mail: konstan@uow.edu.au [Institute for Superconducting and Electronic Materials, AIIM Facility, University of Wollongong Innovation Campus, Squires Way, North Wollongong, NSW 2500 (Australia); Devers, Thierry [Centre de Recherche sur la Matière Divisée, Institut de Physique, site de Chartres, Université d’Orléans (France)

    2013-11-15

    Highlights: • Possible application of cerium-doped α-hematite as ultraviolet filter. • Nanoparticles obtained through co-precipitation technique using various cerium doping levels followed by annealing. • Comprehensive materials characterisation utilizing XRD, DSC/TGA, STEM, UV–vis spectroscopy. • Increasing cerium content reduces particle sizing and alters morphology. • Solubility of cerium in hematite seen between 5 and 10% doping, 10% cerium doping greatly enhances attenuation in ultraviolet region and increases optical bandgap. - Abstract: Metal oxide nanoparticles have potential use in energy storage, electrode materials, as catalysts and in the emerging field of nanomedicine. Being able to accurately tailor the desirable properties of these nanoceramic materials, such as particle size, morphology and optical bandgap (E{sub g}) is integral in the feasibility of their use. In this study we investigate the altering of both the structure and physical properties through the doping of hematite (α-Fe{sub 2}O{sub 3}) nanocrystals with cerium at a range of concentrations, synthesised using a one-pot co-precipitation method. This extremely simple synthesis followed by thermal treatment results in stable Fe{sub 2−x}Ce{sub x}O{sub y} nanoceramics resulting from the burning of any unreacted precursors and transformation of goethite-cerium doped nanoparticle intermediate. The inclusion of Ce into the crystal lattice of these α-Fe{sub 2}O{sub 3} nanoparticles causes a significantly large reduction in mean crystalline size and alteration in particle morphology with increasing cerium content. Finally we report an increase optical semiconductor bandgap, along with a substantial increase in the ultraviolet attenuation found for a 10% Ce-doping concentration which shows the potential application of cerium-doped hematite nanocrystals to be used as a pigmented ultraviolet filter for cosmetic products.

  6. Evolution of the local environment of cerium and neodymium during simplified SON68 glass alteration

    Energy Technology Data Exchange (ETDEWEB)

    Jollivet, Patrick [Commissariat a l' Energie Atomique (CEA), Rhone Valley Research Center, BP 17171, 30207 Bagnols-sur-Ceze (France)]. E-mail: patrick.jollivet@cea.fr; Lopez, Christophe [Commissariat a l' Energie Atomique (CEA), Rhone Valley Research Center, BP 17171, 30207 Bagnols-sur-Ceze (France); Auwer, Christophe Den [Commissariat a l' Energie Atomique (CEA), Rhone Valley Research Center, BP 17171, 30207 Bagnols-sur-Ceze (France); Simoni, Eric [Institut de Physique Nucleaire, Batiment 100, 91406 Orsay cedex (France)

    2005-11-15

    The evolution of the sites occupied by cerium and neodymium (coordination numbers and Ce, Nd-O distances) during alteration of simplified SON68 glass specimens was determined by L{sub III}-edge XAS. Cerium and neodymium are situated in a silicate environment in the glass, surrounded by eight oxygen atoms at an average distance of 2.44 and 2.48 A, respectively. These two rare earth elements exhibit different leaching behavior, however. The main environment of cerium becomes a silicate (d {sub Ce-O} = 2.19 A) with a second oxide or more probably oxyhydroxide site (d {sub Ce-O} = 2.32 A). The cerium coordination number increases by 1 to 3 compared with the glass, depending on the leaching conditions. Neodymium is found mainly in a hydroxycarbonate environment (d {sub Nd-O} = 2.46 A); the second site is a silicate (d {sub Nd-O} = 2.54 A). The neodymium coordination number increases by 1 compared with the glass. When glass containing neodymium is doped with phosphorus, Nd is situated in a phosphate environment; this change is also reflected in the coordination number and Nd-O distance (seven oxygen atoms at 2.42 A). During glass leaching, neodymium is present at two different sites, phosphate (d {sub Nd-O} = 2.52 A) and hydroxycarbonate (d {sub Nd-O} = 2.40 A)

  7. Effects of Cerium on Alloy Elements Distribution in Ferrous Matrix Material

    Institute of Scientific and Technical Information of China (English)

    刘英才; 刘俊友; 尹衍生; 刘国权

    2001-01-01

    The effect of the addition of rare earths in Fe-based high chromium alloy powders on elements distribution in matrix materials and mechanical properties were studied. The results show that the addition of cerium can increase the chromium amount in carbonides and increase the micro-hardness after carbonization and the wear-resistant property of materials.

  8. Transient Dynamics of Fluoride-Based High Concentration Erbium/Cerium Co-Doped Fiber Amplifier

    Institute of Scientific and Technical Information of China (English)

    S. S-H. Yam; Y. Akasaka; Y. Kubota; R. Huang; D. L. Harris; J. Pan

    2003-01-01

    We designed and evaluated a fluoride-based high concentration erbium/ cerium co-doped fiber amplifier. It is suitable for Metropolitan Area Networks due to faster transient, flatter (unfiltered) gain, smaller footprint and gain excursion than its silica-based counterpart.

  9. Release of cerium dibutylphosphate corrosion inhibitors from highly filled epoxy coating systems

    NARCIS (Netherlands)

    Soestbergen, M. van; Baukh, V.; Erich, S.J.F.; Huinink, H.P.; Adan, O.C.G.

    2014-01-01

    Carcinogenic chromates are phased out as corrosion inhibitors in organic coatings, and are replaced by benign alternatives. Cerium-based compounds are excellent corrosion inhibitors in an aqueous environment. However, whether they are effective as corrosion inhibitor in an organic coating also depen

  10. Colloidal stabilization of cerium-gadolinium oxide (CGO) suspensions via rheology

    DEFF Research Database (Denmark)

    Marani, Debora; Sudireddy, Bhaskar Reddy; Bentzen, Janet Jonna;

    2015-01-01

    colloidally stable state. The method was applied to explore the ability of four commercial dispersants (acidic affine, neutral, basic affine, and polyvinylpyrrolidone (PVP)) to disperse cerium-gadolinium oxide (CGO) in ethanol. Only the acidic affine and the PVP dispersants were found to efficiently disperse...

  11. Characteristics of cerium-gadolinium oxide (CGO) suspensions as a function of dispersant and powder properties

    DEFF Research Database (Denmark)

    Phair, John; Lönnroth, Nadja; Lundberg, Mats;

    2009-01-01

    A series of concentrated suspensions ( = 0.18–0.34) of cerium-gadolinium oxide (CGO) in terpineol were prepared as a function of dispersant, powder surface area and solids concentration. The stability of the suspensions was assessed by rheological measurements including viscosity and oscillatory...

  12. Photochemical precipitation of thorium and cerium and their separation from other ions in aqueous solution.

    Science.gov (United States)

    Das, M; Heyn, A H; Hoffman, M Z; Agarwal, R P

    1970-10-01

    Thorium was precipitated from homogeneous solution by exposing solutions of thorium and periodate in dilute perchloric acid to 253.7 nm radiation from a low-pressure mercury lamp. Periodate is reduced photochemically to iodate which causes the formation of a dense precipitate of the basic iodate of thorium(IV). The precipitate was redissolved, the iodate reduced, the thorium precipitated first as the hydroxide, then as the oxalate and ignited to the dioxide for weighing. Thorium(IV) solutions containing 8-200 mg of ThO(2) gave quantitative results with a standard deviation (s) of 0.2 mg. Separations from 25 mg each of iron, calcium, magnesium, 50 mg of yttrium and up to 500 mg of uranium(VI) were quantitative (s = 0.25 mg). Separations from rare earths, except cerium, were accomplished by using hexamethylenetetramine rather than ammonia for the precipitation of the hydroxide. Cerium(III) was similarly precipitated and converted into CeO(2) for weighing. Quantitative results were obtained for 13-150 mg of CeO(2) with a standard deviation of 0.2 mg. Separations from 200 mg of uranium were quantitative. Other rare earths and yttrium interfered seriously. The precipitates of the basic cerium(IV) and thorium iodates obtained are more compact than those obtained by direct precipitation and can be handled easily. Attempts to duplicate Suzuki's method for separating cerium from neodymium and yttrium were not successful. PMID:18960820

  13. Separation of cerium from high level waste solution of Purex origin

    International Nuclear Information System (INIS)

    A simple solvent extraction procedure for the separation of 144Ce from Purex high level waste (HLW) is described. 2-ethylhexyl 2-ethylhexyl phosphonic acid (KSM-17) has been used as extractant. About 10 mCi of cerium was separated from HLW using this technique. This method is amenable for automation and scale up. (author)

  14. Growth and characterization of Sm3+ doped cerium oxalate single crystals

    Directory of Open Access Journals (Sweden)

    Minu Mary C

    2016-07-01

    Full Text Available Single crystals of Sm3+ doped cerium oxalate decahydrate were synthesized using single diffusion gel technique and the conditions influencing the size, morphology, nucleation density and quality of the crystals were optimized. Highly transparent single crystals of average size 3 mm × 2 mm × 1 mm with well-defined hexagonal morphology were grown during a time period of two weeks. X-ray powder diffraction analysis revealed that the grown crystals crystallize in the monoclinic system with space group P21/c as identical with the pure cerium oxalate. The various functional groups of the oxalate ligand and the water of crystallization were identified by Fourier transform infrared spectroscopy. The photoluminescence spectrum of the Sm3+ doped cerium oxalate indicated that the Sm3+ ions are optically active in the cerium oxalate matrix. The crystal has a strong and efficient orange red emission with a wavelength peak at 595 nm and hence can be effectively used for optical amplification. Microhardness measurements of the crystal revealed that they belong to the soft material category.

  15. Growth and characterization of cerium lanthanum oxalate crystals grown in hydro-silica gel

    Energy Technology Data Exchange (ETDEWEB)

    John, M.V.; Ittyachen, M.A. [Mahatma Gandhi Univ., Kerala (India). School of Pure and Applied Physics

    2001-07-01

    Single crystals of mixed cerium lanthanum oxalate (CLO) are grown by gel method. Over the hydrosilica gel prepared by mixing oxalic acid and sodium meta silicate, a mixture of aqueous solutions of cerium nitrate and lanthanum nitrate are poured gently. Cerium and lanthanum ions diffuse into the gel and react with oxalic acid to give colorless, transparent cerium lanthanum oxalate crystals with in a few days. Different growth parameters give crystals of various dimensions. Infrared (IR) spectrum confirms the presence of water molecules and carboxylic acid. X-ray diffraction (XRD) pattern of these samples reveals the crystalline nature. Diffraction peaks are indexed. Unit cell parameters are determined. Thermogravimetric analysis (TGA) and differential thermal analysis (DTA) data support the presence of 9 H{sub 2}O molecules attached to the CLO crystal lattice which are lost around 200 C as revealed by the endotherm record. Exothermic peak around 350 C-425 C shows the release of CO and CO{sub 2}. Elemental analysis done by energy dispersive X-ray fluorescence analysis (EDXRF) for the mixed rare earth compound is almost in good agreement with experimental and theoretical values. (orig.)

  16. Phenotypic and genomic responses to titanium dioxide and cerium oxide nanoparticles in Arabidopsis germinants

    Science.gov (United States)

    The effects of exposure to two nanoparticles (NPs) -titanium dioxide (nano-titania) and cerium oxide (nano-ceria) at 500 mg NPs L-1 on gene expression and growth in Arabidopsis thaliana germinants were studied using microarrays and phenotype studies. After 12 days post treatment,...

  17. Cerium (IV) oxide nanotubes prepared by low temperature deposition at normal pressure

    Energy Technology Data Exchange (ETDEWEB)

    Boehme, M; Fu, G; Ionescu, E; Ensinger, W, E-mail: mboehme@ca.tu-darmstadt.de [Department of Materials Science, Darmstadt University of Technology, D-64287 Darmstadt (Germany)

    2011-02-11

    This paper reports the synthesis of cerium dioxide nanotubes (CeNTs) by electroless deposition using ion-track-etched polycarbonate templates. To achieve nanotubes with thin walls and small surface roughness the tubes were generated by a several-step-containing procedure under aqueous conditions. The approach reported below will process open end nanotubes with well-defined outer diameter and wall thickness.

  18. Cerium (IV) oxide nanotubes prepared by low temperature deposition at normal pressure.

    Science.gov (United States)

    Boehme, M; Fu, G; Ionescu, E; Ensinger, W

    2011-02-11

    This paper reports the synthesis of cerium dioxide nanotubes (CeNTs) by electroless deposition using ion-track-etched polycarbonate templates. To achieve nanotubes with thin walls and small surface roughness the tubes were generated by a several-step-containing procedure under aqueous conditions. The approach reported below will process open end nanotubes with well-defined outer diameter and wall thickness.

  19. miR-126 Is Involved in Vascular Remodeling under Laminar Shear Stress

    Directory of Open Access Journals (Sweden)

    Ana Mondadori dos Santos

    2015-01-01

    Full Text Available Morphology and changes in gene expression of vascular endothelium are mainly due to shear stress and inflammation. Cell phenotype modulation has been clearly demonstrated to be controlled by small noncoding micro-RNAs (miRNAs. This study focused on the effect of laminar shear stress (LSS on human endothelial cells (HUVECs, with an emphasis on the role of miRNA-126 (miR-126. Exposure of HUVECs in vitro to LSS modified the shape of HUVECs and concomitantly regulated the expression of miR-126, vascular cell adhesion molecule 1 (VCAM-1, and syndecan-4 (SDC-4. A significant upregulation of miR-126 during long-term exposure to flow was shown. Interestingly, LSS enhanced SDC-4 expression on the HUVEC membranes. Overexpression of miR-126 in HUVECs decreased the levels of targets stromal cell-derived factor-1 SDF-1/CXCL12 and VCAM-1 but increased the expression of RGS16, CXCR4, and SDC-4. No significant difference in terms of cell proliferation and apoptosis was observed between scramble, anti-miR-126, and pre-miR-126 transfected HUVECs. In Apo-E KO/CKD mice aortas expressing a high level of miR-126, SDC-4 was concomitantly increased. In conclusion, our results suggest that miR-126 (i is overexpressed by long-term LSS, (ii has a role in up- and downregulation of genes involved in atherosclerosis, and (iii affects SDC-4 expression.

  20. Semiempirical Shell Model Tabulated Masses for Translead Elements with Magic Proton Number Z = 126

    OpenAIRE

    Liran, S.; Marinov, A.(Institute for Nuclear Research and Nuclear Energy, Sofia, Bulgaria); Zeldes, N.

    2001-01-01

    We present two tables of calculated masses of translead nuclei, for 351 nuclei with N from 94 to 126 and Z from 82 to 100, and for 1969 nuclei with N from 126 to 184 and Z from 82 to 126. The tables are calculated from a semiempirical shell-model mass equation based on Z = 126 as a proton magic number which seems to be highly extrapolatable inside shell regions. Useful separation and decay energies are given as well. Some properties of the calculated masses and applications to superheavy elem...

  1. 4d → 4f resonance in photoabsorption of cerium ion Ce3+ and endohedral cerium in fullerene complex {\\rm{Ce}}@{{{\\rm{C}}}_{82}}^{+}

    Science.gov (United States)

    Schrange-Kashenock, G.

    2016-09-01

    The theoretical investigation of the single-photoionization spectra in the 4d-resonance region (120-150 eV) for the ionic cerium Ce3+ and cerium in the endohedral complex {{Ce}}@{{{{C}}}82}+ (in practice, {{{Ce}}}3+@{{{{C}}}82}2-) is presented. The fullerene cage is modeled by ab initio spherical jellium shell with an accurate account for the real distribution of carbon electron density. The oscillator strengths are calculated within the multiconfiguration Dirac-Fock (MCDF) approach for phototransitions from the outermost shells of the ion Ce3+ with and without the influence of the potential generated by a fullerene cage. It is shown that the integrated oscillator strengths have the main contribution from the Ce3+ 4d → 4f (ten possible from the phototransitions {}2F{7/2,5/2}\\to {}2D{3/2,5/2},{}2F{5/2,7/2},{}2G{5/2,7/2}) resonance photoexcitations. The corresponding precise MCDF values for the oscillator strengths and the transition energies are presented for the first time. It is demonstrated that the resonance {f}4d\\to 4f oscillator strengths are slightly affected by the presence of the cage potential, despite the fact that the spectral levels structure is changed when the effect of this potential is included. The Auger 4d -1 decay from the cerium free ion Ce3+ and the encapsulated endohedral ion Ce3+@ are considered within the two-step model and the corresponding Lorentzian profiles are presented. This model clearly reveals the correspondence of the complex resonance profile in the Ce3+ photoabsorption to the fine structure of ion energy levels. The smoothing of the resonance profile in the photoabsorption of the endohedral system {{Ce}}@{{{{C}}}82}+ compared with the free ion Ce3+ is attributed to increasing the linewidths of the Auger transitions. This increase is estimated from the relevant experiment (Müller et al 2008 Phys. Rev. Lett. 101 133001) to be strong; as at least three times the value for an isolated ion. The presence of the confining fullerene

  2. 4d → 4f resonance in photoabsorption of cerium ion Ce3+ and endohedral cerium in fullerene complex {\\rm{Ce}}@{{{\\rm{C}}}_{82}}^{+}

    Science.gov (United States)

    Schrange-Kashenock, G.

    2016-09-01

    The theoretical investigation of the single-photoionization spectra in the 4d-resonance region (120–150 eV) for the ionic cerium Ce3+ and cerium in the endohedral complex {{Ce}}@{{{{C}}}82}+ (in practice, {{{Ce}}}3+@{{{{C}}}82}2-) is presented. The fullerene cage is modeled by ab initio spherical jellium shell with an accurate account for the real distribution of carbon electron density. The oscillator strengths are calculated within the multiconfiguration Dirac–Fock (MCDF) approach for phototransitions from the outermost shells of the ion Ce3+ with and without the influence of the potential generated by a fullerene cage. It is shown that the integrated oscillator strengths have the main contribution from the Ce3+ 4d → 4f (ten possible from the phototransitions {}2F{7/2,5/2}\\to {}2D{3/2,5/2},{}2F{5/2,7/2},{}2G{5/2,7/2}) resonance photoexcitations. The corresponding precise MCDF values for the oscillator strengths and the transition energies are presented for the first time. It is demonstrated that the resonance {f}4d\\to 4f oscillator strengths are slightly affected by the presence of the cage potential, despite the fact that the spectral levels structure is changed when the effect of this potential is included. The Auger 4d ‑1 decay from the cerium free ion Ce3+ and the encapsulated endohedral ion Ce3+@ are considered within the two-step model and the corresponding Lorentzian profiles are presented. This model clearly reveals the correspondence of the complex resonance profile in the Ce3+ photoabsorption to the fine structure of ion energy levels. The smoothing of the resonance profile in the photoabsorption of the endohedral system {{Ce}}@{{{{C}}}82}+ compared with the free ion Ce3+ is attributed to increasing the linewidths of the Auger transitions. This increase is estimated from the relevant experiment (Müller et al 2008 Phys. Rev. Lett. 101 133001) to be strong; as at least three times the value for an isolated ion. The presence of the confining

  3. Magnetic hysteresis of cerium doped bismuth ferrite thin films

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, Surbhi [Department of Physics and Astrophysics, University of Delhi (India); Tomar, Monika [Physics Department, Miranda House, University of Delhi (India); Gupta, Vinay, E-mail: drguptavinay@gmail.com [Department of Physics and Astrophysics, University of Delhi (India)

    2015-03-15

    The influence of Cerium doping on the structural and magnetic properties of BiFeO{sub 3} thin films have been investigated. Rietveld refinement of X-ray diffraction data and successive de-convolution of Raman scattering spectra of Bi{sub 1−x}Ce{sub x}FeO{sub 3} (BCFO) thin films with x=0–0.20 reflect the single phase rhombohedral (R3c) formation for x<0.08, whereas concentration-driven gradual structural phase transition from rhombohedral (R3c) to partial tetragonal (P4mm) phase follows for x≥0.08. All low wavenumber Raman modes (<300 cm{sup −1}) showed a noticeable shift towards higher wavenumber with increase in doping concentration, except Raman E-1 mode (71 cm{sup −1}), shows a minor shift. Sudden evolution of Raman mode at 668 cm{sup −1}, manifested as A{sub 1}-tetragonal mode, accompanied by the shift to higher wavenumber with increase in doping concentration (x) affirm partial structural phase transition. Anomalous wasp waist shaped (M–H) hysteresis curves with improved saturation magnetization (M{sub s}) for BCFO thin films is attributed to antiferromagnetic interaction/hybridization between Ce 4f and Fe 3d electronic states. The contribution of both hard and soft phase to the total coercivity is calculated. Polycrystalline Bi{sub 0.88}Ce{sub 0.12}FeO{sub 3} thin film found to exhibit better magnetic properties with M{sub s}=15.9 emu/g without any impure phase. - Highlights: • Synthesis of single phase Bi{sub 1−x}Ce{sub x}FeO{sub 3} thin films with (x=0–0.2) on cost effective corning glass and silicon substrates using CSD technique. • Structural modification studies using Rietveld refinement of XRD and de-convolution of Raman spectra revealed partial phase transition from rhombohedral (R3c) to tetragonal (P4mm) phase. • Possible reasons for origin of pinched magnetic behavior of BCFO thin films are identified. • Contribution of both hard and soft magnetic phase in coercivity of BCFO thin films is calculated and practical

  4. Magnetic hysteresis of cerium doped bismuth ferrite thin films

    International Nuclear Information System (INIS)

    The influence of Cerium doping on the structural and magnetic properties of BiFeO3 thin films have been investigated. Rietveld refinement of X-ray diffraction data and successive de-convolution of Raman scattering spectra of Bi1−xCexFeO3 (BCFO) thin films with x=0–0.20 reflect the single phase rhombohedral (R3c) formation for x<0.08, whereas concentration-driven gradual structural phase transition from rhombohedral (R3c) to partial tetragonal (P4mm) phase follows for x≥0.08. All low wavenumber Raman modes (<300 cm−1) showed a noticeable shift towards higher wavenumber with increase in doping concentration, except Raman E-1 mode (71 cm−1), shows a minor shift. Sudden evolution of Raman mode at 668 cm−1, manifested as A1-tetragonal mode, accompanied by the shift to higher wavenumber with increase in doping concentration (x) affirm partial structural phase transition. Anomalous wasp waist shaped (M–H) hysteresis curves with improved saturation magnetization (Ms) for BCFO thin films is attributed to antiferromagnetic interaction/hybridization between Ce 4f and Fe 3d electronic states. The contribution of both hard and soft phase to the total coercivity is calculated. Polycrystalline Bi0.88Ce0.12FeO3 thin film found to exhibit better magnetic properties with Ms=15.9 emu/g without any impure phase. - Highlights: • Synthesis of single phase Bi1−xCexFeO3 thin films with (x=0–0.2) on cost effective corning glass and silicon substrates using CSD technique. • Structural modification studies using Rietveld refinement of XRD and de-convolution of Raman spectra revealed partial phase transition from rhombohedral (R3c) to tetragonal (P4mm) phase. • Possible reasons for origin of pinched magnetic behavior of BCFO thin films are identified. • Contribution of both hard and soft magnetic phase in coercivity of BCFO thin films is calculated and practical applications of such materials exhibiting pinching behavior are conferred

  5. High temperature condensation and thermal radiation properties of cerium dioxide in solid and liquid states

    International Nuclear Information System (INIS)

    Full Text: Measuring thermal radiation properties of cerium dioxide at high temperatures is very complicated problem from experimental point of view. It is connected with high evaporation of this material at high temperatures. In order to solve this problem with a subsecond laser technique the excess pressure of inert atmosphere is maintained in the working chamber to suppress surface evaporation in the focal area of the sample. In this paper it is shown that in this case the dense vapor phase formed above the investigated sample actively interacts with the sample surface and the laser radiation and distorts the experimental results. The developed polychromatic reflectometer with laser heating enabled one to discover the interesting phenomenon of the interaction of the vapor, liquid and solid phases in cerium dioxide under CO2 laser irradiation. This phenomenon is exhibited in the form of the exothermic peak of the condensation on the cooling curves moreover the temperature level of this transition is regulated by experimental parameters. The possibility of the change of the position of this floating phase transition on the temperature scale permits one to model the interaction of liquid-vapor and solid-vapor to estimate the contribution of the dense vapor phase formed above the sample to the thermal radiation properties of cerium dioxide at high temperatures. The experimental data on thermal radiation properties of stoichiometric cerium dioxide in the spectral range 0.4-1.1 μm and in the temperature region 2000-3500 K measured by the method developed are presented. Reflectivity and emissivity measurement error does not exceed ±3 %. The experimental results obtained are compared with the data of other authors and the recommended values for spectral reflectivity and emissivity of cerium dioxide at high temperatures are given. (author)

  6. Using cerium anomaly as an indicator of redox reactions in constructed wetland

    Science.gov (United States)

    Liang, R.

    2013-12-01

    The study area, Chiayi County located in southern Taiwan, has highly developed livestock. The surface water has very low dissolved oxygen and high NH4. Under the situation, constructed wetland becomes the most effective and economic choice to treat the wastewater in the natural waterways. Hebao Island free surface constructed wetland started to operate in late 2006. It covers an area of 0.28 km2 and is subdivided into 3 major cells, which are sedimentation cell, 1st aeration cell with rooted plants and 2nd aeration cell with float plants. The water depth of cells ranges from 0.6 m to 1.2 m. The total hydraulic retention time is about a half day. In this study, the water samples were sequentially collected along the flow path. The results of hydrochemical analysis show that the untreated inflow water can be characterized with enriched NH4 (11 ppm), sulfate (6 ppm) and arsenic (50 ppb). The removal efficiency of NH4 in the first two cells is pollutants from the wastewater; therefore, dissolved oxygen is traditionally considered as an important indicator to evaluate the operation efficiency of wetland. However, it would need longer time to achieve equilibrium state of redox reaction involving dissolved oxygen due to the slower reaction rate. For example, the input water in this study has fairly high dissolved oxygen (5 ppm) but the NH4 content is still high, which indicates a non-equilibrium condition. In this study, the cerium anomaly is alternatively utilized to evaluate the water redox state. The results demonstrate that the input water has the negative cerium anomaly of -0.16. Along the flow path, the cerium negative anomaly does not change in the first two cells and dramatically becomes -0.23 in cell 3. The trend of cerium anomaly is more close to the removal efficiency of NH4 rather than dissolve oxygen. Accordingly, cerium anomaly could become a better indicator of removal efficiency of constructed wetland.

  7. Can the 126 GeV boson be a pseudoscalar?

    CERN Document Server

    Coleppa, Baradhwaj; Logan, Heather E

    2012-01-01

    We test the possibility that the newly-discovered 126 GeV boson is a pseudoscalar by examining the correlations among the loop-induced pseudoscalar decay branching fractions to $\\gamma\\gamma$, $ZZ^*$, $Z\\gamma$, and $WW^*$ final states in a model-independent way. These four decays are controlled by only two effective operators, so that the rates in $Z\\gamma$ and $WW^*$ are predicted now that the rates in $\\gamma\\gamma$ and $ZZ^*,Z\\gamma^* \\to 4 \\ell$ have been measured. We find that the pseudoscalar possibility is disfavored but not conclusively excluded. Experimental exclusion of the $Z\\gamma$ decay to well below $\\sigma/\\sigma_{\\rm SM} \\sim 170$ or conclusive observation of the $WW^*$ decay near the Standard Model rate would eliminate the pseudoscalar possibility. The $Z\\gamma$ exclusion should be possible using existing data. The only loophole in our argument is the possibility that the $4\\ell$ signal comes from pseudoscalar decays to a pair of new neutral gauge bosons with mass near the $Z$ pole.

  8. 33 CFR 126.28 - Ammonium nitrate, ammonium nitrate fertilizers, fertilizer mixtures, or nitro carbo nitrate...

    Science.gov (United States)

    2010-07-01

    ... nitrate fertilizers, fertilizer mixtures, or nitro carbo nitrate; general provisions. 126.28 Section 126..., ammonium nitrate fertilizers, fertilizer mixtures, or nitro carbo nitrate; general provisions. (a) When any item of ammonium nitrate, ammonium nitrate fertilizers, fertilizer mixtures, or nitro carbo...

  9. 34 CFR 75.126 - Application must list all programs to which it is submitted.

    Science.gov (United States)

    2010-07-01

    ... 34 Education 1 2010-07-01 2010-07-01 false Application must list all programs to which it is submitted. 75.126 Section 75.126 Education Office of the Secretary, Department of Education DIRECT GRANT... all programs to which it is submitted. If an applicant is submitting an application for the...

  10. Effects of PCB 126 and cadmium on the anaerobic metabolism of the mussel Mytilus edulis L

    NARCIS (Netherlands)

    Eertman, R.H.M.; Zurburg, W.; Schipper, C.A.; Sandee, B.; Smaal, A.C.

    1996-01-01

    Exposure of mussels to PCB 126 and/or cadmium resulted in elevated anaerobic metabolic activity during 48 hr of aerial exposure. In mussels exposed to PCB 126 or cadmium this was achieved by an increased opine production. The largest increase was observed in PCB exposed mussels. In mussels that were

  11. 13 CFR 126.800 - Who may protest the status of a qualified HUBZone SBC?

    Science.gov (United States)

    2010-01-01

    ... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Who may protest the status of a qualified HUBZone SBC? 126.800 Section 126.800 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION... apparent successful offeror's qualified HUBZone SBC status....

  12. 22 CFR 126.1 - Prohibited exports and sales to certain countries.

    Science.gov (United States)

    2010-04-01

    ... applies to countries with respect to which the United States maintains an arms embargo (e.g., Burma, China... type enumerated on the United States Munitions List (22 CFR part 121), irrespective of origin, are... countries. 126.1 Section 126.1 Foreign Relations DEPARTMENT OF STATE INTERNATIONAL TRAFFIC IN...

  13. 49 CFR 572.126 - Knees and knee impact test procedure.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 7 2010-10-01 2010-10-01 false Knees and knee impact test procedure. 572.126... TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) ANTHROPOMORPHIC TEST DEVICES Six-year-old Child Test Dummy, Beta Version § 572.126 Knees and knee impact test procedure. (a)...

  14. 13 CFR 126.303 - Where must a concern submit its application and certification?

    Science.gov (United States)

    2010-01-01

    ... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Where must a concern submit its application and certification? 126.303 Section 126.303 Business Credit and Assistance SMALL BUSINESS... certification? A concern seeking certification as a HUBZone SBC must submit either an electronic application...

  15. 13 CFR 126.305 - What format must the certification to SBA take?

    Science.gov (United States)

    2010-01-01

    ... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false What format must the certification to SBA take? 126.305 Section 126.305 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION... submit the required information in either a written or electronic application form provided by SBA....

  16. 50 CFR 648.126 - Protection of threatened and endangered sea turtles.

    Science.gov (United States)

    2010-10-01

    ... sea turtles. This section supplements existing regulations issued to regulate incidental take of sea turtles under authority of the Endangered Species Act under 50 CFR parts 222 and 223. In addition to the... sea turtles. 648.126 Section 648.126 Wildlife and Fisheries FISHERY CONSERVATION AND...

  17. Study on No- carrier-added Separation of 126Sn From High-level Liquid Waste

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    126Sn is a long-lived fission product nuclide, its fission yield values, in fission of 235U by thermalneutron, fission spectrum neutron and high energy neutron, are 5.59×10-2%, 1.39×10-1% and 1.76%,respectively. So scientists are paying more attention to 126Sn in high radioactive waste disposal.

  18. Reactions between cerium(IV) and methyl-6-x-derivatives of aniline in perchloric acid solutions

    International Nuclear Information System (INIS)

    The oxidation of 2,6-dimethyl-, 2-isopropyl-6-methyl, 2-chloro-6-methyl-and 2-methyl-6-nitro aniline with cerium(IV) in perchloric acid solutions has been examined. It has been found that the concentration of hydrogen ions and the basicity of nitrogen atom in the amine group decide about the resultant intermediate products. Some of these products can be practically prepared using cerium(IV) as an oxidizing agent. (author). 16 refs, 1 tab

  19. Titrimetric and Spectrophotometric Assay of Ganciclovir in Pharmaceuticals Using Cerium(IV) Sulphate as the Oxidimetric Agent

    OpenAIRE

    Pavagada J. Ramesh; Kanakapura Basavaiah; Cijo M. Xavier; Prashanth, Kudige N.; Raghu, Madihalli S.; Kanakapura B. Vinay

    2012-01-01

    Titrimetric and spectrophotometric assay of ganciclovir (GNC) is described using cerium(IV) sulphate as the oxidimetric reagent. The methods are based on the oxidation of GNC with a measured excess of cerium(IV) sulphate in acid medium followed by determination of the unreacted oxidant by two different reaction schemes. In titrimetry, the unreacted oxidant was determined by back titration with ferrous ammonium sulphate (FAS) in sulphuric acid medium, and spectrophotometry involves the reactio...

  20. Chromatographic separation of cerium(Ⅲ) in L-valine medium using poly[dibenzo-18-crown-6

    Institute of Scientific and Technical Information of China (English)

    SABALE Sandip R; MOHITE Baburao S

    2009-01-01

    A column chromatographic method has been developed for the separation and determination of cerium(Ⅲ) using poly[dibenzo-18-crown-6]. The separation was carried out in L-valine medium. The adsorption of cerium(Ⅲ) was quantitative from 1×10-1 to 1×10-4 mol/L L-valine. Amongst the various eluents, 1.0-8.0 mol/L hydrochloric acid, 1.0-8.0 mol/L hydrobromic acid, 1.0-8.0 mol/L perchloric acid, 1.0-2.0 mol/L sulfuric acid and 4.0-5.0 mol/L acetic acid, were found to be the efficient eluents for cerium(Ⅲ). The capacity of poly[dibenzo-18-crown-6] for cerium(Ⅲ) was (0.428±0.01) mmol/g. The method was applied to the separation of cerium(Ⅲ) from associated elements link uranium(Ⅵ) and thorium(Ⅳ). It was also applied for the determination of cerium(Ⅲ) in geological samples. The method is simple, rapid and selective with good reproducibility (approximately±2% ).

  1. Syndecan-1 responsive microRNA-126 and 149 regulate cell proliferation in prostate cancer

    Energy Technology Data Exchange (ETDEWEB)

    Fujii, Tomomi; Shimada, Keiji [Department of Pathology, Nara Medical University School of Medicine, Nara (Japan); Tatsumi, Yoshihiro [Department of Pathology, Nara Medical University School of Medicine, Nara (Japan); Department of Urology, Nara Medical University School of Medicine, Nara (Japan); Fujimoto, Kiyohide [Department of Urology, Nara Medical University School of Medicine, Nara (Japan); Konishi, Noboru, E-mail: nkonishi@naramed-u.ac.jp [Department of Pathology, Nara Medical University School of Medicine, Nara (Japan)

    2015-01-02

    Highlights: • Syndecan-1 is highly expressed in androgen independent prostate cancer cells, PC3. • Syndecan-1 regulates the expression of miR-126 and -149 in prostate cancer cells. • MiR-126 and 149 control cell growth via p21 induction and senescence mechanism. • MiR-126 and 149 promote cell proliferation by suppressing SOX2, NANOG, and Oct4. - Abstract: MicroRNAs (miRNAs) are short (19–24 nt), low molecular weight RNAs that play important roles in the regulation of target genes associated with cell proliferation, differentiation, and development, by binding to the 3′-untranslated region of the target mRNAs. In this study, we examined the expression of miRNA-126 (miR-126) and miR-149 in prostate cancer, and investigated the molecular mechanisms by which they affect syndecan-1 in prostate cancer. Functional analysis of miR-126 and miR-149 was conducted in the prostate cancer cell lines, PC3, Du145, and LNCaP. The expression levels of SOX2, NANOG, Oct4, miR-126 and miR-149 were evaluated by quantitative RT-PCR. After silencing syndecan-1, miR-126, and/or miR-149 in the PC3 cells, cell proliferation, senescence, and p21 induction were assessed using the MTS assay, senescence-associated β-galactosidase (SA-β-Gal) assay, and immunocytochemistry, respectively. Compared to the Du145 and LNCaP cells, PC3 cells exhibited higher expression of syndecan-1. When syndecan-1 was silenced, the PC3 cells showed reduced expression of miR-126 and miR-149 most effectively. Suppression of miR-126 and/or miR-149 significantly inhibited cell growth via p21 induction and subsequently, induced senescence. The mRNA expression levels of SOX2, NANOG, and Oct4 were significantly increased in response to the silencing of miR-126 and/or miR-149. Our results suggest that miR-126 and miR-149 are associated with the expression of syndecan-1 in prostate cancer cells. These miRNAs promote cell proliferation by suppressing SOX2, NANOG, and Oct4. The regulation of these factors by mi

  2. Color-Fading Spectrophotometric Determination of Cerium with DBC-Arsenazo

    Institute of Scientific and Technical Information of China (English)

    翟庆洲; 张晓霞

    2004-01-01

    In the medium of 0.18~1.08 mol·L-1 sulfuric acid, cerium(Ⅳ) has the color-fading effect on DBC-arsenazo. The apparent molar absorptivity of the color-fading reaction is ε530 nm=1.03×104 L·mol-1·cm-1. Beer′s law is obeyed over the range of 1.20~12.0 μg·ml-1 of Ce (Ⅳ) which shows a linear relationship with the decrease in the absorbance of the colored solution. The effect of thirty-six coexisting ions was studied. The method was applied to the determination of the trace amount of cerium in water samples and has the advantage of high accuracy and good selectivity.

  3. Improvement and analysis of the hydrogen-cerium redox flow cell

    Science.gov (United States)

    Tucker, Michael C.; Weiss, Alexandra; Weber, Adam Z.

    2016-09-01

    The H2-Ce redox flow cell is optimized using commercially-available cell materials. Cell performance is found to be sensitive to the upper charge cutoff voltage, membrane boiling pretreatment, methanesulfonic-acid concentration, (+) electrode surface area and flow pattern, and operating temperature. Performance is relatively insensitive to membrane thickness, Cerium concentration, and all features of the (-) electrode including hydrogen flow. Cell performance appears to be limited by mass transport and kinetics in the cerium (+) electrode. Maximum discharge power of 895 mW cm-2 was observed at 60 °C; an energy efficiency of 90% was achieved at 50 °C. The H2-Ce cell is promising for energy storage assuming one can optimize Ce reaction kinetics and electrolyte.

  4. Deposition of cerium contained conversion films on LC4 alloy with square wave pulse method

    Institute of Scientific and Technical Information of China (English)

    ZHANG Wei; LI Jiuqing; WU Yinshun; ZHANG Pei; HE Jianping

    2004-01-01

    Cerium contained conversion films were deposited on LC4 aluminum alloy using square wave pulse (SWP) in a CeC13 solution with KMnO4 as the oxidant. Energy dispersive spectroscopy (EDS) and scanning electron microscopy (SEM) were adopted to study the composition and the morphology of the film. It is found that the film is composed of Al, Zn, Cu,and small amount of cerium. The polarization curves of the specimens treated with SWP technique measured in 3.5% (mass fraction) NaCl solution reveal that the film thus formed inhibits both the anodic and cathodic process of the corrosion of the specimen. The immersion tests of treated specimens in 3.5% NaCl solution indicate that the corrosion resistance of the SWP treated specimen is better than that of the untreated and is equivalent to or even better than that of the traditionally electrochemically treated specimens.

  5. Monte Carlo radiative transfer simulation of a cavity solar reactor for the reduction of cerium oxide

    Energy Technology Data Exchange (ETDEWEB)

    Villafan-Vidales, H.I.; Arancibia-Bulnes, C.A.; Dehesa-Carrasco, U. [Centro de Investigacion en Energia, Universidad Nacional Autonoma de Mexico, Privada Xochicalco s/n, Col. Centro, A.P. 34, Temixco, Morelos 62580 (Mexico); Romero-Paredes, H. [Departamento de Ingenieria de Procesos e Hidraulica, Universidad Autonoma Metropolitana-Iztapalapa, Av. San Rafael Atlixco No.186, Col. Vicentina, A.P. 55-534, Mexico D.F 09340 (Mexico)

    2009-01-15

    Radiative heat transfer in a solar thermochemical reactor for the thermal reduction of cerium oxide is simulated with the Monte Carlo method. The directional characteristics and the power distribution of the concentrated solar radiation that enters the cavity is obtained by carrying out a Monte Carlo ray tracing of a paraboloidal concentrator. It is considered that the reactor contains a gas/particle suspension directly exposed to concentrated solar radiation. The suspension is treated as a non-isothermal, non-gray, absorbing, emitting, and anisotropically scattering medium. The transport coefficients of the particles are obtained from Mie-scattering theory by using the optical properties of cerium oxide. From the simulations, the aperture radius and the particle concentration were optimized to match the characteristics of the considered concentrator. (author)

  6. Growth of monodisperse nanocrystals of cerium oxide during synthesis and annealing

    International Nuclear Information System (INIS)

    Monodisperse cerium oxide nanocrystals have been successfully synthesised using simple ammonia precipitation technique from cerium(III) nitrate solution at different temperatures in the range 35-80 oC. The activation energy for growth of CeO2 nanocrystals during the precipitation is calculated as 11.54 kJ/mol using Arrhenius plot. Average crystal diameter was obtained from XRD analysis, HR-TEM and light scattering (PCS). The analysis of size data from HR-TEM images and PCS clearly indicated the formation of highly crystalline CeO2 particles in narrow size range. CeO2 nanocrystals precipitated at 35 oC were further annealed at temperatures in the range 300-700 oC. The activation energy for crystal growth during annealing is also calculated and is close to the reported values. An effort is made to predict the mechanism of crystal growth during the precipitation and annealing.

  7. A cerium-lead redox flow battery system employing supporting electrolyte of methanesulfonic acid

    Science.gov (United States)

    Na, Zhaolin; Xu, Shengnan; Yin, Dongming; Wang, Limin

    2015-11-01

    A novel cerium-lead redox flow battery (RFB) employing Ce(IV)/Ce(III) and Pb(II)/Pb redox couples in the supporting electrolyte of methanesulfonic acid (MSA) is developed and preliminarily investigated. The RFB requires no additional catalyst and uses kinetically favorable reactions between low-cost reactants, and provides a desirable discharge voltage of approximately 1.7 V, with high average coulombic efficiency (CE) of 92% and energy efficiency (EE) of 86% over 800 cycles at 298 K. Stable cycling with an acceptable performance is achieved for a board operating temperature range of 253 K-313 K. The excellent performance obtained from the preliminary study suggests that the cerium-lead RFB promises to be applicable to large-scale energy storage for electricity grids.

  8. Synthesis of mesoporous cerium-zirconium mixed oxides by hydrothermal templating method

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Mesoporous cerium-zirconium mixed oxides were prepared by hydrothermal method using cetyl trimethyl ammonium bromide (CTAB) as template.The effects of amount of template,pH value of solution and hydrothermal temperature on mesostructure of samples were systematically investigated.The final products were characterized by XRD,TEM,FT-IR,and BET.The results indicate that all the cerium-zirconium mixed oxides present a meso-structure.At molar ratio of n(CTAB)/n((Ce)+(Zr))=0.15,pH value of 9,and hydrothermal temperature of 120 ℃,the samples obtained possess a specific surface area of 207.9 m2/g with pore diameter of 3.70 nm and pore volume of 0.19 cm3/g.

  9. Energy transfer and thermal studies of Pr3+ doped cerium oxalate crystals

    Indian Academy of Sciences (India)

    R Pragash; Gijo Jose; N V Unnikrishnan; C Sudarsanakumar

    2011-07-01

    Energy transfer process at room temperature for cerium (sensitizer) oxalate single crystals doped with different concentrations (10, 13, 15, 17 and 20%) of praseodymium ions (activator) grown by hydro silica gel method has been evaluated. The analysis of energy level diagrams of cerium and praseodymium ions indicates that the energy gap between the sensitizer and the activator ions varies in a small range suggesting a possible energy transfer from the Ce3+ to Pr3+. The emission and absorption spectra of these crystals were recorded. The overlapping of the absorption spectra of Pr3+ and emission spectra of Ce3+ at wavelengths 484 and 478 nm, respectively, strongly supports the possible energy transfer process in this system. From the absorption spectra, oscillator strength, electric dipole moment, branching ratio and Judd–Ofelt parameters of this system were evaluated by least square programming. The quantum efficiency, energy transfer probabilities and thermal properties have been studied.

  10. Reduction behavior of cerium(Ⅲ) ions in NaCl-2CsCl melt

    Institute of Scientific and Technical Information of China (English)

    QI Xue; ZHU Hongmin

    2005-01-01

    The cathodic process of cerium(Ⅲ) ions in NaCl-2CsCl melt was studied by cyclic voltammetry and square wave voltammetry with tungsten and gold electrodes at 873 K. The two electroanalytical methods yield similar results. The cathodic process of cerium(Ⅲ) ions consists of two reversible steps: Ce3+ + e-= Ce2+ and Ce2+ + 2e-= Ce. The half wave potentials of Ce3+/Ce2+ and Ce2+/Ce were determined as -2.525 V vs. Cl2/Cl- and -2.975 V vs. Cl2/Cl-, respectively. The diffusion coefficient of Ce3+ was also determined as 5.5 × 10-5 cm2·s-1.

  11. Thermodynamics of the α -γ transition in cerium studied by an LDA + Gutzwiller method

    Science.gov (United States)

    Tian, Ming-Feng; Song, Hai-Feng; Liu, Hai-Feng; Wang, Cong; Fang, Zhong; Dai, Xi

    2015-03-01

    Utilizing the local-density approximation (LDA) + Gutzwiller method, we have studied the α -γ transition in cerium. Our results indicate that the volume collapse transition between α and γ phases is present at zero temperature with negative pressure. By further providing a newly finite temperature generalization of the LDA + Gutzwiller method (using the mean-field potential approach), the entropy contributed by both electronic quasiparticles and lattice vibration included, we obtain the Gibbs free energy at a given volume and temperature, from which we get the α -γ transition at finite temperature and pressure. Our results indicate that the electronic entropy and lattice vibrational entropy both play important roles in the α -γ transition. We also calculated the equation of state and phase diagram of cerium, finding good agreement with the experiments.

  12. Effect of cerium oxide addition on electrical and physical properties of alkali borosilicate glasses

    International Nuclear Information System (INIS)

    The study of electrical conductivity, density and coefficient of thermal expansion (CTE) of Na2O:K2O:B2O3:SiO2:BaO glass samples with addition of cerium oxide has been carried out. It has been observed that the addition of cerium oxide affects the electrical conductivity, density and CTE. The results have been explained on the basis of the variation in number of bridging oxygens (BOs) and non-bridging oxygens (NBOs) present in the glass. In general, the glass with more NBOs has a weak network which exhibits higher electrical conductivity. The weakening of the network has been supported by the observed decrease in density and increase in CTE for the glasses.

  13. Tyrphostin AG126 exerts neuroprotection in CNS inflammation by a dual mechanism.

    Science.gov (United States)

    Menzfeld, Christiane; John, Michael; van Rossum, Denise; Regen, Tommy; Scheffel, Jörg; Janova, Hana; Götz, Alexander; Ribes, Sandra; Nau, Roland; Borisch, Angela; Boutin, Philippe; Neumann, Konstantin; Bremes, Vanessa; Wienands, Jürgen; Reichardt, Holger M; Lühder, Fred; Tischner, Denise; Waetzig, Vicky; Herdegen, Thomas; Teismann, Peter; Greig, Iain; Müller, Michael; Pukrop, Tobias; Mildner, Alexander; Kettenmann, Helmut; Brück, Wolfgang; Prinz, Marco; Rotshenker, Shlomo; Weber, Martin S; Hanisch, Uwe-Karsten

    2015-06-01

    The putative protein tyrosine kinase (PTK) inhibitor tyrphostin AG126 has proven beneficial in various models of inflammatory disease. Yet molecular targets and cellular mechanisms remained enigmatic. We demonstrate here that AG126 treatment has beneficial effects in experimental autoimmune encephalomyelitis (EAE), a model for multiple sclerosis. AG126 alleviates the clinical symptoms, diminishes encephalitogenic Th17 differentiation, reduces inflammatory CNS infiltration as well as microglia activation and attenuates myelin damage. We show that AG126 directly inhibits Bruton's tyrosine kinase (BTK), a PTK associated with B cell receptor and Toll-like receptor (TLR) signaling. However, BTK inhibition cannot account for the entire activity spectrum. Effects on TLR-induced proinflammatory cytokine expression in microglia involve AG126 hydrolysis and conversion of its dinitrile side chain to malononitrile (MN). Notably, while liberated MN can subsequently mediate critical AG126 features, full protection in EAE still requires delivery of intact AG126. Its anti-inflammatory potential and especially interference with TLR signaling thus rely on a dual mechanism encompassing BTK and a novel MN-sensitive target. Both principles bear great potential for the therapeutic management of disturbed innate and adaptive immune functions. PMID:25731696

  14. Effect of cerium addition on microstructure and texture of aluminum foil for electrolytic capacitors

    Institute of Scientific and Technical Information of China (English)

    王海燕; 李文学; 任慧平; 黄丽颖; 王向阳

    2010-01-01

    Anode foil of aluminum electrolytic capacitor,which requires large surface area for high capacitance,were prepared by rolling,annealing and electrochemical etching.Effects of cerium addition on the capacitance of aluminum electrolytic capacitors were investigated.Microstructure of the aluminum foil surface was observed by optical microscopy(OM) and scanning electron microscopy(SEM).Electron back scattered diffraction(EBSD) was also employed to reveal texture evolvement of cold-rolled aluminum foil after ann...

  15. A cerium glass fiber-optic active target for high energy physics experiments

    International Nuclear Information System (INIS)

    A fiber-optic plate imaging system has been developed for active target and tracking applications, in which the active element is Ce(3+) in a silicate glass. Particle tracks and interactions have been recorded with a hit density of greater than or equal to 4/mm for minimum ionizing particles and with a spatial resolution sigma approx. = 28μ m.) The properties of cerium scintillation glass are discussed

  16. Untangling the biological effects of cerium oxide nanoparticles: the role of surface valence states

    OpenAIRE

    Gerardo Pulido-Reyes; Ismael Rodea-Palomares; Soumen Das; Tamil Selvan Sakthivel; Francisco Leganes; Roberto Rosal; Sudipta Seal; Francisca Fernández-Piñas

    2015-01-01

    Cerium oxide nanoparticles (nanoceria; CNPs) have been found to have both pro-oxidant and anti-oxidant effects on different cell systems or organisms. In order to untangle the mechanisms which underlie the biological activity of nanoceria, we have studied the effect of five different CNPs on a model relevant aquatic microorganism. Neither shape, concentration, synthesis method, surface charge (ζ-potential), nor nominal size had any influence in the observed biological activity. The main drive...

  17. Theoretical modeling of heterogeneous catalysts based on platinum and cerium oxide

    OpenAIRE

    Bruix Fusté, Albert

    2014-01-01

    This thesis focuses on the computational study of models for platinum catalysts supported on cerium oxide (CeO2) which are of technological relevance. In these catalysts, ceria is often found acting as a non-inert support, leading to complex metal-support interactions (MSI) that modify the properties of both the oxide and the supported metal. First principles computational methods based on the Density functional Theory (DFT) have been used to study the nature of these interactions and their e...

  18. Redox-active cerium oxide nanoparticles protect human dermal fibroblasts from PQ-induced damage

    OpenAIRE

    Claudia von Montfort; Lirija Alili; Sarah Teuber-Hanselmann; Peter Brenneisen

    2014-01-01

    Recently, it has been published that cerium (Ce) oxide nanoparticles (CNP; nanoceria) are able to downregulate tumor invasion in cancer cell lines. Redox-active CNP exhibit both selective pro-oxidative and antioxidative properties, the first being responsible for impairment of tumor growth and invasion. A non-toxic and even protective effect of CNP in human dermal fibroblasts (HDF) has already been observed. However, the effect on important parameters such as cell death, proliferation and red...

  19. Nanocrystalline cerium dioxide efficacy for gastrointestinal motility: potential for prokinetic treatment and prevention in elderly

    OpenAIRE

    Yefimenko, Olena Yu; Savchenko, Yuliya O; Tetyana M. Falalyeyeva; Beregova, Tetyana V; Zholobak, Nadiya M; Spivak, Mykola Ya; Shcherbakov, Oleksandr B; Bubnov, Rostyslav V

    2015-01-01

    Background Constipation is a common condition, with prevalence after 65 years, is a major colorectal cancer risk factor. Recent works have demonstrated advances in personalized, preventive nanomedicine, leading to the construction of new materials and nanodrugs, in particular, nanocrystalline cerium dioxide (NCD), having strong antioxidative prebiotic effect. The aim of our study was to investigate the influence of NCD on motor function of the stomach and colon in vivo and contractive activit...

  20. Cerium regulates expression of alternative methanol dehydrogenases in Methylosinus trichosporium OB3b.

    Science.gov (United States)

    Farhan Ul Haque, Muhammad; Kalidass, Bhagyalakshmi; Bandow, Nathan; Turpin, Erick A; DiSpirito, Alan A; Semrau, Jeremy D

    2015-11-01

    Methanotrophs have multiple methane monooxygenases that are well known to be regulated by copper, i.e., a "copper switch." At low copper/biomass ratios the soluble methane monooxygenase (sMMO) is expressed while expression and activity of the particulate methane monooxygenase (pMMO) increases with increasing availability of copper. In many methanotrophs there are also multiple methanol dehydrogenases (MeDHs), one based on Mxa and another based on Xox. Mxa-MeDH is known to have calcium in its active site, while Xox-MeDHs have been shown to have rare earth elements in their active site. We show here that the expression levels of Mxa-MeDH and Xox-MeDH in Methylosinus trichosporium OB3b significantly decreased and increased, respectively, when grown in the presence of cerium but the absence of copper compared to the absence of both metals. Expression of sMMO and pMMO was not affected. In the presence of copper, the effect of cerium on gene expression was less significant, i.e., expression of Mxa-MeDH in the presence of copper and cerium was slightly lower than in the presence of copper alone, but Xox-MeDH was again found to increase significantly. As expected, the addition of copper caused sMMO and pMMO expression levels to significantly decrease and increase, respectively, but the simultaneous addition of cerium had no discernible effect on MMO expression. As a result, it appears Mxa-MeDH can be uncoupled from methane oxidation by sMMO in M. trichosporium OB3b but not from pMMO. PMID:26296730

  1. Cerium Biomagnification in a Terrestrial Food Chain: Influence of Particle Size and Growth Stage.

    Science.gov (United States)

    Majumdar, Sanghamitra; Trujillo-Reyes, Jesica; Hernandez-Viezcas, Jose A; White, Jason C; Peralta-Videa, Jose R; Gardea-Torresdey, Jorge L

    2016-07-01

    Mass-flow modeling of engineered nanomaterials (ENMs) indicates that a major fraction of released particles partition into soils and sediments. This has aggravated the risk of contaminating agricultural fields, potentially threatening associated food webs. To assess possible ENM trophic transfer, cerium accumulation from cerium oxide nanoparticles (nano-CeO2) and their bulk equivalent (bulk-CeO2) was investigated in producers and consumers from a terrestrial food chain. Kidney bean plants (Phaseolus vulgaris var. red hawk) grown in soil contaminated with 1000-2000 mg/kg nano-CeO2 or 1000 mg/kg bulk-CeO2 were presented to Mexican bean beetles (Epilachna varivestis), which were then consumed by spined soldier bugs (Podisus maculiventris). Cerium accumulation in plant and insects was independent of particle size. After 36 days of exposure to 1000 mg/kg nano- and bulk-CeO2, roots accumulated 26 and 19 μg/g Ce, respectively, and translocated 1.02 and 1.3 μg/g Ce, respectively, to shoots. The beetle larvae feeding on nano-CeO2 exposed leaves accumulated low levels of Ce since ∼98% of Ce was excreted in contrast to bulk-CeO2. However, in nano-CeO2 exposed adults, Ce in tissues was higher than Ce excreted. Additionally, Ce content in tissues was biomagnified by a factor of 5.3 from the plants to adult beetles and further to bugs.

  2. The role of hydrogen peroxide in the deposition of cerium-based conversion coatings

    International Nuclear Information System (INIS)

    Cerium-based conversion coatings are progressing as an effective alternative to hazardous chromate-based systems used in the treatment of metal surfaces. However, there is still considerable debate over the mechanism by which these coatings are formed. Here, titrations of cerium-based conversion coating solutions were carried out in order to model the reactions that occur at the metal-solution interface during coating, with a particular emphasis on investigating the role of hydrogen peroxide (H2O2). The titration curves obtained support the proposed formation of Ce(III) peroxo complexes such as Ce(H2O2)3+ as an initial step, followed by deprotonation, oxidation and precipitation to form peroxo-containing Ce(IV) species such as Ce(IV)(O2)(OH)2. The precipitates resulting from titrations were characterised by Raman spectroscopy, X-ray diffraction and thermogravimetric analysis, confirming the presence of peroxo bonds, and nano-sized CeO2 crystallites that decreased in size with increasing H2O2 concentration. Characterisation of cerium conversion coatings on aluminium alloy surfaces confirmed the presence of peroxo species in the coatings, thereby supporting the titration model

  3. Synthesis and Characterization of Cerium Doped Titanium Catalyst for the Degradation of Nitrobenzene Using Visible Light

    Directory of Open Access Journals (Sweden)

    Padmini Ellappan

    2014-01-01

    Full Text Available Cerium doped catalyst was synthesized using Titanium isopropoxide as the Titanium source. The metal doped nanoparticles semiconductor catalyst was prepared by sol-sol method with the sol of Cerium. The synthesized catalyst samples were characterized by powder X-ray diffraction, BET surface area, thermogravimetric analysis (TGA, scanning electron microscopy (SEM, and UV-vis diffuse reflectance measurements (DRS and compared with undoped TiO2 catalyst. The photocatalytic activity of the sample was investigated for the decomposition of nitrobenzene (NB using visible light as the artificial light source. Cerium doped catalyst was found to have better degradation of nitrobenzene owing to its shift in the band gap from UV to visible region as compared to undoped TiO2 catalyst. The operational parameters were optimized with catalyst dosage of 0.1 g L−1, pH of 9, and light intensity of 500 W. The degradation mechanism followed the Langmuir Hinshelwood kinetic model with the rate constant depending nonlinearly on the operational parameters as given by the relationship Kapp (theoretical = 2.29 * 10−4 * Intensity0.584 * Concentration−0.230 * Dosage0.425 * pH0.336.

  4. Infrared, thermal and X-ray diffraction analysis of cerium soaps

    Energy Technology Data Exchange (ETDEWEB)

    Mehrotra, K.N. [Agra Univ. (India). Dept. of Chemistry; Chauhan, M. [Agra Univ. (India). Dept. of Chemistry; Shukla, R.K. [R.B.S. Coll., Agra (India)

    1997-03-01

    The physico-chemical characteristics of cerium soaps (Caproate and caprate) in solid state were investigated by IR, thermal and X-ray diffraction measurements. The IR results reveal that the fatty acids exist in dimeric state through hydrogen bonding and soaps possess partial ionic character. The decomposition reaction was found kinetically of zero order with energy of activation 6.7 and 7.3 K cal mol{sup -1} for cerium caproate and caprate, respectively. The X-ray diffraction measurements were used to calculate the long spacings and the results confirm the double layer structure of cerium soaps. (orig.) [Deutsch] Mit Hilfe von IR-, thermischen und Roentgendiffraktionsmessungen wurden die physikalisch-chemischen Eigenschaften von Cerseifen (Capron- und Caprylsaeuresalze)in festem Zustand bestimmt. Die IR-Untersuchungen zeigen, dass die Fettseifen in dimerem Zustand, gebunden durch Wasserstoffbruecken vorliegen und partiell ionischen Charakter haben. Die Zersetzungsreaktion war von einer Kinetik nullter Ordnung, die Aktivierungsenergien lagen bei 6,7 K cal mol{sup -1} fuer Capronsaeuresalze und 7,3 K cal mol{sup -1} fuer Caprylsaeuresalze. Mit Hilfe von Roentgendiffraktionsmessungen wurden die grossen Zwischenraeume bestimmt. Die Ergebnisse lassen auf eine Doppelschichtstruktur der Cerseifen schliessen. (orig.)

  5. Cerium, gallium and zinc containing mesoporous bioactive glass coating deposited on titanium alloy

    Science.gov (United States)

    Shruti, S.; Andreatta, F.; Furlani, E.; Marin, E.; Maschio, S.; Fedrizzi, L.

    2016-08-01

    Surface modification is one of the methods for improving the performance of medical implants in biological environment. In this study, cerium, gallium and zinc substituted 80%SiO2-15%CaO-5%P2O5 mesoporous bioactive glass (MBG) in combination with polycaprolactone (PCL) were coated over Ti6Al4 V substrates by dip-coating method in order to obtain an inorganic-organic hybrid coating (MBG-PCL). Structural characterization was performed using XRD, nitrogen adsorption, SEM-EDXS, FTIR. The MBG-PCL coating uniformly covered the substrate with the thickness found to be more than 1 μm. Glass and polymer phases were detected in the coating along with the presence of biologically potent elements cerium, gallium and zinc. In addition, in vitro bioactivity was investigated by soaking the coated samples in simulated body fluid (SBF) for up to 30 days at 37 °C. The apatite-like layer was monitored by FTIR, SEM-EDXS and ICP measurements and it formed in all the samples within 15 days except zinc samples. In this way, an attempt was made to develop a new biomaterial with improved in vitro bioactive response due to bioactive glass coating and good mechanical strength of Ti6Al4 V alloy along with inherent biological properties of cerium, gallium and zinc.

  6. Specifics of new phase crystal nucleation during isostructural γ↔α transformation in cerium

    International Nuclear Information System (INIS)

    Specifics of new phase nucleation and subsequent growth under γ-α-transformation in cerium near the surface of the sample is suggested. It is assumed that this specifics can effect mechanical behaviour of a laminar sample under transition at three-point bend. Measurement of deflection of cerium samples at the sensitivity of ∼ 10-6 m at three-point loading was carried out in the 4.2-300 K temperature range at p=10-4 GPa as well as in a chamber of high pressure (in the range of hydrostatic pressures up to 1.0 GPa at T=293 K). It is shown that the effects of change in the form experimentally discovered in the given paper and accompanying isostructural γ-α-transformation in cerium may be explained by the fact that crystal nucleation of γ- and α-phases differing by the volume takes place mainly from the surface of the sample and not in its volume

  7. Cerium modified Y/SBA-15 composite molecular sieve catalyzed synthesis ofn-butyl acetate

    Institute of Scientific and Technical Information of China (English)

    史春薇; 吴文远; 边雪; 裴明远; 赵杉林; 陈平

    2016-01-01

    A novel Ce-Y/SBA-15 catalyst was prepared by modifying HY/SBA-15 microporous-mesoporous composite molecular sieve with cerium using the impregnation method. The characterization results from scanning electron microscopy/energy dispersive X-ray dispersive spectroscopy (SEM/EDS), transmission electron microscopy (TEM), and X-ray fluorescence (XRF) studies indi-cated that the Ce-modified catalyst maintained the microporous-mesoporous structure of Y/SBA-15. The Ce ions were found to be uniformly dispersed in the pores of the molecular sieve without aggregation. The results from pyrolysis coupled-Fourier transform in-frared spectroscopy (Pyridine-FTIR) and temperature programmed desorption of ammonia (NH3-TPD) showed that the loading of ce-rium caused the hydroxyl group in the catalyst to display stronger Bronsted acidity. The efficiency of the modified Ce-Y/SBA-15 catalyst was evaluated by using it to catalyze the synthesis ofn-butyl acetate. The optimal synthesis conditions were determined by orthogonal experiments. The highest esterification yield of 94.4% was obtained when the reaction time was 2.0 h, with acid/alcohol molar ratio of 1:1.2, and catalyst loading of 10 wt.%. The results in this study demonstrated that the loading of cerium and the structure of Y/SBA-15 microporous-mesoporous composite molecular sieve helped in improving the catalytic activity of this acidic catalyst.

  8. Controlled Redox Chemistry at Cerium within a Tripodal Nitroxide Ligand Framework.

    Science.gov (United States)

    Bogart, Justin A; Lippincott, Connor A; Carroll, Patrick J; Booth, Corwin H; Schelter, Eric J

    2015-12-01

    Ligand reorganization has been shown to have a profound effect on the outcome of cerium redox chemistry. Through the use of a tethered, tripodal, trianionic nitroxide ligand, [((2-tBuNOH)C6 H4 CH2 )3 N](3-) (TriNOx (3-) ), controlled redox chemistry at cerium was accomplished, and typically reactive complexes of tetravalent cerium were isolated. These included rare cationic complexes [Ce(TriNOx )thf][BAr(F) 4 ], in which Ar(F) =3,5-(CF3 )2 -C6 H3 , and [Ce(TriNOx )py][OTf]. A rare complete Ce-halide series, Ce(TriNOx )X, in which X=F(-) , Cl(-) , Br(-) , I(-) , was also synthesized. The solution chemistry of these complexes was explored through detailed solution-phase electrochemistry and (1) H NMR experiments and showed a unique shift in the ratio of species with inner- and outer-sphere anions with size of the anionic X(-) group. DFT calculations on the series of calculations corroborated the experimental findings.

  9. Chromium VI adsorption on cerium oxide nanoparticles and morphology changes during the process

    International Nuclear Information System (INIS)

    In this study, suspended cerium oxide nanoparticles stabilized with hexamethylenetetramine were used for the removal of dissolved chromium VI in pure water. Several concentrations of adsorbent and adsorbate were tested, trying to cover a large range of possible real conditions. Results showed that the Freundlich isotherm represented well the adsorption equilibrium reached between nanoparticles and chromium, whereas adsorption kinetics could be modeled by a pseudo-second-order expression. The separation of chromium-cerium nanoparticles from the medium and the desorption of chromium using sodium hydroxide without cerium losses was obtained. Nanoparticles agglomeration and morphological changes during the adsorption-desorption process were observed by TEM. Another remarkable result obtained in this study is the low toxicity in the water treated by nanoparticles measured by the Microtox commercial method. These results can be used to propose this treatment sequence for a clean and simple removal of drinking water or wastewater re-use when a high toxicity heavy metal such as chromium VI is the responsible for water pollution.

  10. Effect of cerium oxide addition on electrical properties of ZnO

    Energy Technology Data Exchange (ETDEWEB)

    Ibrahim, D.M. [National Research Center, Dokki, Giza (Egypt). Dept. of Ceramics; Mounir, M. [Dept. of Physics, Cairo Univ., Giza (Egypt); Mahgoub, A.S. [Cairo Univ., Giza (Egypt). Dept. of Chemistry; Turky, G. [Dept. of Physics, National Research Center, Dokki, Giza (Egypt); El-Desouky, O.A. [Cer. Cleopatra Co., Ramadan City (Egypt)

    2002-07-01

    Mixtures of ZnO and Ce{sub 6} O{sub 11} as additive were prepared by solid state reaction from the calcined oxides with the following proportions: 0.03, 0.08, 0.1, 0.2 and 0.4 mole. Disc specimens 1.2 cm 5 cm in diameter and 0.3 cm thickness were processed under a force of 70 kN and fired at 1150 C/ 30 minutes. XRD revealed the presence of limited solid solution of cerium in ZnO, as evident from the shift in the peaks [0.03-0.04 A ] up to 0.1 mole addition and remains constant. SEM revealed the presence of inter-granular phase. EDAX showed it to be a mixture of ZnO and Ce{sub 6}O{sub 11}. Also cerium was detected in the ZnO grains confirming the XRD results. RCL circuit was used to measure the capacitance and resistance at different frequencies at room temperature. The dielectric constant and conductivity were calculated. The change in resistivity with temperature was followed up to 523 K. The change in dielectric strength with temperature at spot frequency of 10 kHz is demonstrated. The electrical conductivity was found to increase with the proportion of cerium oxide up to 0.2 mole then decreased. (orig.)

  11. Laser ablated plasma plume diagnostics of cerium oxide: effect of oxygen partial pressure

    International Nuclear Information System (INIS)

    This paper describes the spatial and temporal investigation of laser ablated plasma plume of cerium oxide target using Langmuir probe to measure the plasma parameters. Cerium oxide target was ablated using a KrF (λ ∼ 248 nm) gas laser at an energy of 300 mJ per pulse. Experimental studies confirmed that oxygen partial pressure of 2 x 10-2 mbar is sufficient enough to get good quality films of cerium oxide. At this pressure, plume was diagnosed for their spatial and temporal behaviour. The tungsten probe tip was inserted along the length of the plasma to collect the ions and electrons effectively. A thin probe tip (about 0.4 mm diameter) was used to avoid plasma perturbation during measurements. A variable voltage was applied to the tip and corresponding current due to electrons and ions was collected. Spatial distribution was investigated at a regular interval of 15 mm from the target up maximum distance 45 mm and the temporal behaviour was recorded in the range of 0 to 50 μS with an interval of 0.5 μS. The ion and average electron density are found to be maximum at 30 mm from the target position and the plasma current of ceria is found to be maximum at 22 μS. (author)

  12. Development of Stable Cerium Zirconium Mixed Oxide Nanoparticle Additive for Emission Reduction in Biodiesel Blends

    Directory of Open Access Journals (Sweden)

    Sajith V

    2015-06-01

    Full Text Available Harmful emissions associated with the use of biodiesel is a serious issue and various fuel additives are being used for the reduction of emissions as well as for the improvement of engine performance. Use of cerium oxide nanoparticles as fuel additive is one of the methods for the reduction of emissions, due to its peculiar redox functionality and oxygen buffering capability. Doping of ceria with transition metals such as zirconium improves its Oxygen storage capacity and thermal stability, thereby enhancing simultaneous oxidation and reduction reactions. The present work focuses on the development of cerium zirconium mixed oxide nanoparticle based additive for the reduction of emissions from diesel engine fuelled with biodiesel - diesel blends. Cerium zirconium mixed oxide was synthesized by means of co precipitation method. The stability of the nanofluids was improved by the addition of surfactant, namely Oleic acid. The optimum concentration of surfactant was determined based on estimation of critical micelle concentration, by means of standard tests. Stability of catalytic nanoparticle in fuel was evaluated from the measurement of Zeta potential. Various properties were determined as per ASTM standards to investigate the effect of the nanoparticles on fuel properties. Addition of catalytic nanoparticle in diesel - biodiesel blends does not significantly affect the fuel properties. Engine performance and emission tests were conducted on single cylinder diesel engine to assess the potential of synthesized nanofuel and 15% average reduction of NO emissions was observed for B5 and B10 blends with 15 ppm of catalytic nanoparticle concentration.

  13. Microstructure and electrochemical behavior of cerium conversion coating modified with silane agent on magnesium substrates

    Science.gov (United States)

    Lei, Li; Shi, Jing; Wang, Xin; Liu, Dan; Xu, Haigang

    2016-07-01

    The cerium conversion coating with and without different concentrations of silane agent bis-(γ-triethoxysilylpropyl)-tetrasulfide (BTESPT) modification is obtained on magnesium alloys. Detailed properties of the coatings and the role of BTESPT as an additive are studied and followed with careful discussion. The coating morphology, wettability, chemical composition and corrosion resistance are characterized by scanning electronic microscope (SEM), water contact-angle, X-ray photoelectron spectroscopy (XPS), potentiodynamic measurements and electrochemical impedance spectroscopy (EIS). The electrochemical behavior of the coatings is investigated using EIS. The results indicate that the coating morphology and composition can be controlled by changing silane concentration. The combination of cerium ions and silane molecules could promote the formation of more homogenous and higher hydrophobic coating. The coating turns to be more compact and the adhesive strength between the coating and the magnesium substrate are strongly improved with the formation of Sisbnd Osbnd Si and Sisbnd Osbnd M chemical bonds. The optimum corrosion resistance of the coating in the corrosive media is obtained by 25 ml L-1 BTESPT modification. This whole study implies that the cerium conversion coating modified with certain silane agent deserves cautiousness before its application for corrosion resistance.

  14. Effect of coating parameters on the microstructure of cerium oxide conversion coatings

    International Nuclear Information System (INIS)

    The microstructure and morphology of cerium oxide conversion coatings prepared under different deposition conditions were characterized by transmission electron microscopy (TEM). The coatings were formed by a spontaneous reaction between a water-based solution containing CeCl3 and aluminum alloy 7075-T6 substrates. Microstructural characterization was performed to determine the crystallinity of the coatings and to obtain a better understanding of the deposition parameters on coating microstructure. The results of TEM imaging and electron diffraction analysis indicated that the as-deposited coating was composed of nanocrystalline particles of a previously unreported cerium compound. The particles of the coatings produced using glycerol as an additive were found to be much finer than those of the coatings prepared in the absence of glycerol. This indicates that glycerol may act as a grain refiner and/or growth inhibitor during coating deposition. After deposition, the coated panels were treated for 5 min in a phosphate sealing solution. The sealing treatment converted the as-deposited coating into hydrated cerium phosphate. Panels coated from solutions containing no glycerol followed by phosphate sealing performed poorly in salt fog tests. With glycerol addition, the corrosion resistance of the coatings that were phosphate sealed improved considerably, achieving an average passing rate of 85%

  15. Cerium Biomagnification in a Terrestrial Food Chain: Influence of Particle Size and Growth Stage.

    Science.gov (United States)

    Majumdar, Sanghamitra; Trujillo-Reyes, Jesica; Hernandez-Viezcas, Jose A; White, Jason C; Peralta-Videa, Jose R; Gardea-Torresdey, Jorge L

    2016-07-01

    Mass-flow modeling of engineered nanomaterials (ENMs) indicates that a major fraction of released particles partition into soils and sediments. This has aggravated the risk of contaminating agricultural fields, potentially threatening associated food webs. To assess possible ENM trophic transfer, cerium accumulation from cerium oxide nanoparticles (nano-CeO2) and their bulk equivalent (bulk-CeO2) was investigated in producers and consumers from a terrestrial food chain. Kidney bean plants (Phaseolus vulgaris var. red hawk) grown in soil contaminated with 1000-2000 mg/kg nano-CeO2 or 1000 mg/kg bulk-CeO2 were presented to Mexican bean beetles (Epilachna varivestis), which were then consumed by spined soldier bugs (Podisus maculiventris). Cerium accumulation in plant and insects was independent of particle size. After 36 days of exposure to 1000 mg/kg nano- and bulk-CeO2, roots accumulated 26 and 19 μg/g Ce, respectively, and translocated 1.02 and 1.3 μg/g Ce, respectively, to shoots. The beetle larvae feeding on nano-CeO2 exposed leaves accumulated low levels of Ce since ∼98% of Ce was excreted in contrast to bulk-CeO2. However, in nano-CeO2 exposed adults, Ce in tissues was higher than Ce excreted. Additionally, Ce content in tissues was biomagnified by a factor of 5.3 from the plants to adult beetles and further to bugs. PMID:26690677

  16. Cerium Modified Pillared Montmorillonite Supported Cobalt Catalysts for Fischer Tropsch Synthesis

    International Nuclear Information System (INIS)

    Fischer-Tropsch (FT) synthesis was accomplished over Al-pillared Montmorillonite supported 20 wt% Co modified with different weight% of cerium catalysts. These catalysts were prepared by impregnation method while structural characterizations of the prepared samples were performed by XRD, TPR, NH/sub 3/TPD, TGA, BET, XRF and SEM techniques. The Fischer Tropsch reaction was studied in fixed bed micro catalytic reactor at temperature range of 220, 260 and 275 degree C and at different pressure (1, 5 and 10 bars). From the activity results, it was found that by pillaring NaMMT with Al higher catalytic activity and lower methane selectivity of NaMMT was achieved. Furthermore, the results of FT synthesis reaction revealed that cerium incorporation increased the dispersion of Co/sub 3/O/sub 4/ on the surface and consequently resulted in enhanced catalytic activity. Additionally, the C/sub 5/-C/sub 12/ hydrocarbons and methane selectivity increased while C/sub 22+/ hydrocarbons selectivity was decreased over cerium modified catalysts. Higher reaction temperature (>220 degree C) resulted in significant enhancement in CO conversion and methane selectivity. Though, increase in pressure from 1 to 10 bars eventually resulted in increase in C/sub 5+/ hydrocarbons and decrease in methane and C/sub 2/-C/sub 5/ hydrocarbons selectivity. (author)

  17. Cerium valence change in the solid solutions Ce(Rh1-xRux)Sn

    International Nuclear Information System (INIS)

    The solid solutions Ce(Rh1-xRux)Sn were investigated by means of susceptibility measurements, specific heat, electrical resistivity, X-ray absorption spectroscopy (XAS), and 119Sn Moessbauer spectroscopy. Magnetic measurements as well as XAS data show a cerium valence change in dependence on the ruthenium content. Higher ruthenium content causes an increase from 3.22 to 3.45 at 300 K. Furthermore χ and χ-1 data indicate valence fluctuation for cerium as a function of temperature. For example, Ce(Rh0.8Ru0.2)Sn exhibits valence fluctuations between 3.42 and 3.32 in the temperature range of 10 to 300 K. This could be proven by using the interconfiguration fluctuation (ICF) model introduced by Sales and Wohlleben. Cerium valence change does not influence the tin atoms as proven by 119Sn Moessbauer spectroscopy, but it influences the electrical properties. Ce(Rh0.9Ru0.1)Sn behaves like a typical valence fluctuating compound, and higher ruthenium content causes an increase of the metallic behavior. (orig.)

  18. Influence of agglomeration of cerium oxide nanoparticles and speciation of cerium(III) on short term effects to the green algae Chlamydomonas reinhardtii

    International Nuclear Information System (INIS)

    Highlights: • Phosphate-dispersed CeO2 NP did not affect photosynthetic yield in C. reinhardtii. • Agglomerated CeO2 NP slightly decreased photosynthetic yield. • Cerium(III) was shown to affect photosynthetic yield and intracellular ROS level. • Slight effects of CeO2 NP were caused by dissolved Ce3+ ions present in suspensions. • Wild type and cell wall free mutant of C. reinhardtii showed the same sensitivity. - Abstract: Cerium oxide nanoparticles (CeO2 NP) are increasingly used in industrial applications and may be released to the aquatic environment. The fate of CeO2 NP and effects on algae are largely unknown. In this study, the short term effects of CeO2 NP in two different agglomeration states on the green algae Chlamydomonas reinhardtii were examined. The role of dissolved cerium(III) on toxicity, its speciation and the dissolution of CeO2 NP were considered. The role of cell wall of C. reinhardtii as a barrier and its influence on the sensitivity to CeO2 NP and cerium(III) was evaluated by testing both, the wild type and the cell wall free mutant of C. reinhardtii. Characterization showed that CeO2 NP had a surface charge of ∼0 mV at physiological pH and agglomerated in exposure media. Phosphate stabilized CeO2 NP at pH 7.5 over 24 h. This effect was exploited to test CeO2 NP dispersed in phosphate with a mean size of 140 nm and agglomerated in absence of phosphate with a mean size of 2000 nm. The level of dissolved cerium(III) in CeO2 NP suspensions was very low and between 0.1 and 27 nM in all tested media. Exposure of C. reinhardtii to Ce(NO3)3 decreased the photosynthetic yield in a concentration dependent manner with EC50 of 7.5 ± 0.84 μM for wild type and EC50 of 6.3 ± 0.53 μM for the cell wall free mutant. The intracellular level of reactive oxygen species (ROS) increased upon exposure to Ce(NO3)3 with effective concentrations similar to those inhibiting photosynthesis. The agglomerated CeO2 NP caused a slight decrease of

  19. Influence of agglomeration of cerium oxide nanoparticles and speciation of cerium(III) on short term effects to the green algae Chlamydomonas reinhardtii

    Energy Technology Data Exchange (ETDEWEB)

    Röhder, Lena A. [Eawag, Swiss Federal Institute of Aquatic Science and Technology, Department of Environmental Toxicology, Dübendorf 8600 (Switzerland); ETH-Zurich, Institute of Biogeochemistry and Pollutant Dynamics, Zürich 8092 (Switzerland); Brandt, Tanja [Eawag, Swiss Federal Institute of Aquatic Science and Technology, Department of Environmental Toxicology, Dübendorf 8600 (Switzerland); Sigg, Laura [Eawag, Swiss Federal Institute of Aquatic Science and Technology, Department of Environmental Toxicology, Dübendorf 8600 (Switzerland); ETH-Zurich, Institute of Biogeochemistry and Pollutant Dynamics, Zürich 8092 (Switzerland); Behra, Renata, E-mail: Renata.behra@eawag.ch [Eawag, Swiss Federal Institute of Aquatic Science and Technology, Department of Environmental Toxicology, Dübendorf 8600 (Switzerland)

    2014-07-01

    Highlights: • Phosphate-dispersed CeO₂ NP did not affect photosynthetic yield in C. reinhardtii. • Agglomerated CeO₂ NP slightly decreased photosynthetic yield. • Cerium(III) was shown to affect photosynthetic yield and intracellular ROS level. • Slight effects of CeO₂ NP were caused by dissolved Ce³⁺ ions present in suspensions. • Wild type and cell wall free mutant of C. reinhardtii showed the same sensitivity. - Abstract: Cerium oxide nanoparticles (CeO₂ NP) are increasingly used in industrial applications and may be released to the aquatic environment. The fate of CeO₂ NP and effects on algae are largely unknown. In this study, the short term effects of CeO₂ NP in two different agglomeration states on the green algae Chlamydomonas reinhardtii were examined. The role of dissolved cerium(III) on toxicity, its speciation and the dissolution of CeO₂ NP were considered. The role of cell wall of C. reinhardtii as a barrier and its influence on the sensitivity to CeO₂ NP and cerium(III) was evaluated by testing both, the wild type and the cell wall free mutant of C. reinhardtii. Characterization showed that CeO₂ NP had a surface charge of ~0 mV at physiological pH and agglomerated in exposure media. Phosphate stabilized CeO₂ NP at pH 7.5 over 24 h. This effect was exploited to test CeO₂ NP dispersed in phosphate with a mean size of 140 nm and agglomerated in absence of phosphate with a mean size of 2000 nm. The level of dissolved cerium(III) in CeO₂ NP suspensions was very low and between 0.1 and 27 nM in all tested media. Exposure of C. reinhardtii to Ce(NO₃)₃ decreased the photosynthetic yield in a concentration dependent manner with EC₅₀ of 7.5 ± 0.84 μM for wild type and EC₅₀ of 6.3 ± 0.53 μM for the cell wall free mutant. The intracellular level of reactive oxygen species (ROS) increased upon exposure to Ce(NO₃)₃ with effective concentrations similar to those inhibiting photosynthesis. The agglomerated Ce

  20. Evaluation of mechanically treated cerium (IV) oxides as corrosion inhibitors for galvanized steel

    International Nuclear Information System (INIS)

    The use of cerium salts as corrosion inhibitors for hot dip galvanized steel has been object of a numerous studies in the last few years. The role of cerium ions as corrosion inhibitors was proved: cerium is able to block the cathodic sites of the metal, forming insoluble hydroxides and oxides on the zinc surface. This fact leads to a dramatic decrease of the cathodic current densities and, therefore, to a reduction the overall corrosion processes. On the other hand, the potential of cerium oxides as corrosion inhibitors was also proposed. However, the real effectiveness of this kind of anticorrosive pigments has not been clarified yet. In this work cerium (IV) oxides are considered as corrosion inhibitors for galvanized steel. The corrosion inhibition mechanism of mechanically treated (milled) CeO2 alone and in combination with milled SiO2 nanoparticles was investigated. For this purpose milled CeO2, CeO2 and SiO2 milled together and milled SiO2 particles were studied as corrosion inhibitors in water solution. Therefore, the different mechanically treated particles were dispersed in 0.1 M NaCl solution to test their effectiveness as corrosion inhibitors for galvanized steel. The galvanized steel was immersed in the different solutions and the corrosion inhibition efficiency of the different particles was measured by means of electrochemical techniques. For this purpose, electrochemical impedance spectroscopy (EIS) measurements were carried out, monitoring the evolution of the corrosion processes occurring at the metal surface with the immersion time in the solution. The effect of the different pigments was also investigated by carrying out anodic and cathodic polarization measurements. The polarization curves were acquired under conditions of varied pH. The experimental measurements suggest that the mechanical treatment performed on the SiO2 and CeO2 particles promote the formation of an effective corrosion pigment. The tests evidence also the beneficial effect of

  1. 77 FR 41473 - Proposed Technical Standard Order (TSO)-C126b, 406 MHz Emergency Locator Transmitters (ELT) and...

    Science.gov (United States)

    2012-07-13

    ... Federal Aviation Administration Proposed Technical Standard Order (TSO)-C126b, 406 MHz Emergency Locator... Transmitter (ELT) Equipment, and TSO-C126/C126a, 406 MHz Emergency Locator Transmitters (ELT) AGENCY: Federal...) Transportation Safety Board of Canada Aviation Safety Advisory A11W0151-D1-A2, Loose Attachment of Kannad 406...

  2. 46 CFR 126.160 - Tests and inspections during repairs or alterations, or during riveting, welding, burning, or...

    Science.gov (United States)

    2010-10-01

    ... during riveting, welding, burning, or other hot work. 126.160 Section 126.160 Shipping COAST GUARD... § 126.160 Tests and inspections during repairs or alterations, or during riveting, welding, burning, or... riveting, welding, burning, or other hot work may commence. (c) Each examination must be conducted...

  3. Yeast Interacting Proteins Database: YER081W, YPR126C [Yeast Interacting Proteins Database

    Lifescience Database Archive (English)

    Full Text Available YPR126C - Dubious open reading frame unlikely to encode a functional protein, based on available experimental and comparative...ubious open reading frame unlikely to encode a functional protein, based on available experimental and comparative

  4. High Power Narrow Linewidth 1.26 Micron Ho-Doped Fiber Amplifier Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This proposal is for the development of an innovative, high power, and extremely reliable 1.26-micron Ho-doped fluoride fiber amplifier. The proposed fiber...

  5. Estimating Magic Numbers Larger Than 126 by Fermi-Yang Liming Method

    Institute of Scientific and Technical Information of China (English)

    LI Xian-Hui; ZHOU Zhi-Ning; ZHONG Yu-Shu; YANG Ze-Sen

    2001-01-01

    The Fermi Yang Liming method is followed and developed to estimate new magic numbers in nuclei with a Woods Saxon density function. The calculated results predict that the magic number next to 126 should be around 184 and 258.

  6. 126例结核性腹膜炎临床分析%Clinical Analysis of 126 Cases of Tuberculous Peritonitis

    Institute of Scientific and Technical Information of China (English)

    刘风霞; 战云飞

    2011-01-01

    Objective To analyze the clinical characteristics of tuberculosis preitonitis and explore the diagnosis and treatment methods.Methods Analyze 126 cases who had tubeculous peritonitis diagnoded in our hospital retrospectively.Results 79.3% ( 100/126) of the cases have incrsased biood sedimentation rates.PPD testings are positive in 62.2% (74/119 ) of the cases.39.7% (50/126)have anti-tuberculosis antibody.Abdomen B-ultrasonic are positive in 78.6% (99/126).Abdomen CT examinations are positive in 48.7% (38/78).X-ray examinations of breast are positive in 40.5% (51/126).Activity of ascitos adenosine deaminase(ADA) increased in 73.9% (34/46).Peritoneoscopy showed positive findings in 88% ( 16/18 ).Petitoneum bispoy is in 100/100 (6/6).By means of prompt diagnosis and reasonal medication,the total treatment effective rate was 80.15%.Conclusion The level of clinical diagnosis and treatment for tuberculous peritonitis could be elevated by making the correct final diagnosis combined with the different ways and with the routine drug treatnent of internal medicine and surgical intervention.%目的 分析结核性腹膜炎的临床特点,探讨其诊断和治疗方法.方法 分析2002年3月~2009年1月我院确诊126例结核性腹膜炎患者的临床特点.结果 各项检查的阳性率分别为血沉增快79.3%(100/126),PPD阳性62.2%(74/119),血结核抗体39.7(50/126),腹部B超78.6%(99/126),腹部CT 48.7(38/78),胸部X线片40.5%(51/126),腹水腺苷酸脱氨酶(ADA)活性增高73.9(34/46),腹腔镜检查阳性88.9%(16/18),腹膜活检100%(6/6),通过各项诊断方法及时诊断,合理用药,治疗总有效率达 80.15%.结论 联合不同诊断方法,正确诊断,联合长期用药,必要时配以手术治疗,可提高结核性腹膜炎的临床诊治水平.

  7. Cyanex 923 as the extractant in a rare earth element impurity analysis of high-purity cerium oxide.

    Science.gov (United States)

    Duan, Taicheng; Li, Hongfei; Kang, JianZhen; Chen, Hangting

    2004-06-01

    In this work, the feasibility of employing Cyanex 923 as an extractant into the non-cerium REE (rare earth elements) impurity analysis of high-purity cerium oxide was investigated. Through investigations on the choice of the extraction medium, the optimium extraction acidity, matrix Ce4+ effect on the non-cerium REE ion extraction, the optimium extractant concentration and suitable extracting time, and oscillation strengh, it was found that when the phase ratio was at 1:1 and the acicidity was about 2% H2SO4, by gently shaking by hand for about 2 min, 10 mL of 30% Cyanex 923 could not extract even for a 20 ng amount of non-cerium REE3+ ions. However, the extraction efficiency for Ce4+ of 100 mg total amount under the same conditions was about 96%, indicating that a 25-fold preconcentration factor could be achieved. Thus, it was concluded that Cyanex 923 could be used in a REE impurity analysis of 99.9999% or so pure cerium oxide for primary sepapation to elimilate matrix-induced interferences encountered in an ICP-MS (inductively coupled plasma mass spectroscopy) determination.

  8. Self-poled transparent and flexible UV light-emitting cerium complex-PVDF composite: a high-performance nanogenerator.

    Science.gov (United States)

    Garain, Samiran; Sinha, Tridib Kumar; Adhikary, Prakriti; Henkel, Karsten; Sen, Shrabanee; Ram, Shanker; Sinha, Chittaranjan; Schmeißer, Dieter; Mandal, Dipankar

    2015-01-21

    Cerium(III)-N,N-dimethylformamide-bisulfate [Ce(DMF)(HSO4)3] complex is doped into poly(vinylidene fluoride) (PVDF) to induce a higher yield (99%) of the electroactive phases (β- and γ-phases) of PVDF. A remarkable enhancement of the output voltage (∼32 V) of a nanogenerator (NG) based on a nonelectrically poled cerium(III) complex containing PVDF composite film is achieved by simple repeated human finger imparting, whereas neat PVDF does not show this kind of behavior. This high electrical output resembles the generation of self-poled electroactive β-phase in PVDF due to the electrostatic interactions between the fluoride of PVDF and the surface-active positive charge cloud of the cerium complex via H-bonding and/or bipolar interaction among the opposite poles of cerium complex and PVDF, respectively. The capacitor charging capability of the flexible NG promises its applicability as piezoelectric-based energy harvester. The cerium(III) complex doped PVDF composite film exhibit an intense photoluminescence in the UV region, which might be due to a participation of electron cloud from negative pole of bipolarized PVDF. This fact may open a new area for prospective development of high-performance energy-saving flexible solid-state UV light emitters. PMID:25523039

  9. 126 kV GIS用绝缘拉杆的研制%Preparation of Insulated Tension Pole for 126 kV GIS

    Institute of Scientific and Technical Information of China (English)

    范孝红; 史明; 董伟志; 杜超云

    2014-01-01

    采用环氧树脂、液态酸酐胶粘剂,将玻璃布与聚酯纤维布卷绕到模具中,在真空压力下浸渍,经高温固化制成真空浸胶环氧玻璃布管,并通过无丝扣粘接装配金属接头制成126 kV GIS用绝缘拉杆。对绝缘拉杆基材的力学性能和电性能进行测试,并对绝缘拉杆成品按其使用要求进行测试。结果表明:采用无丝扣粘接工艺研制的126 kV GIS用绝缘拉杆能满足126 kV GIS断路器的使用要求。%Using glass cloth and polyester fiber cloth wind a mold then impregnate the adhesive com-posed of epoxy resin and liquid anhydride under vacuum pressure, a VPI epoxy glass cloth tube was pre-pared after cured at high temperature. An insulated tension pole for 126 kV GIS was prepared using VPI epoxy glass cloth tube bond with metallic joint by unthreaded bonding technique. The mechanical proper-ties and electrical properties of the base material and end product of insulated tension pole were tested. The results show that the prepared insulated tension pole can meet the application requirements of 126 kV GIS.

  10. Effect of cerium additive and secondary phase analysis on Ag0.5Bi0.5TiO3 ceramics

    Indian Academy of Sciences (India)

    S Supriya; Antonio J Dos Santos-García; F Fernández-Martinez

    2016-02-01

    Cerium-doped silver bismuth titanate—Ag0.5Bi0.5TiO3 (ABT) ceramics have been synthesized by the high-temperature solid-state reaction method. The structure and elemental examination of the prepared ceramic was analysed by X-ray diffraction (XRD), Fourier transform infrared, scanning electron microscopy and energydispersive spectroscopy. XRD analysis showed the presence of pyrochlore structure and secondary phase when more than 5 mol% cerium was added. The impact of temperature on cerium-doped silver bismuth titanate samples was analysed by differential thermal analysis and differential scanning calorimetry. Cerium doping caused the flaky morphology comparing with undoped sample. The homogeneity of all the samples was discussed in detail by diffuse reflectance spectrum. This is the first time the reflection process is analysed for the cerium-doped ABT system to the best of our knowledge.

  11. Ab initio molecular dynamics study of the properties of cerium in liquid sodium at 1000 K temperature

    Energy Technology Data Exchange (ETDEWEB)

    Samin, Adib; Li, Xiang; Zhang, Jinsuo [Nuclear Engineering Program, Department of Mechanical and Aerospace Engineering, The Ohio State University, 201 W 19th Avenue, Columbus, Ohio 43210 (United States); Mariani, R. D. [Idaho National Laboratory, Materials and Fuels Complex, Idaho Falls, Idaho 83415 (United States); Unal, Cetin [Los Alamos National Laboratory, P.O. Box 1663, Los Alamos, New Mexico 87545 (United States)

    2015-12-21

    For liquid-sodium-cooled fast nuclear reactor systems, it is crucial to understand the behavior of lanthanides and other potential fission products in liquid sodium or other liquid metal solutions such as liquid cesium-sodium. In this study, we focus on lanthanide behavior in liquid sodium. Using ab initio molecular dynamics, we found that the solubility of cerium in liquid sodium at 1000 K was less than 0.78 at. %, and the diffusion coefficient of cerium in liquid sodium was calculated to be 5.57 × 10{sup −9} m{sup 2}/s. Furthermore, it was found that cerium in small amounts may significantly alter the heat capacity of the liquid sodium system. Our results are consistent with the experimental results for similar materials under similar conditions.

  12. Ab initio molecular dynamics study of the properties of cerium in liquid sodium at 1000 K temperature

    Science.gov (United States)

    Samin, Adib; Li, Xiang; Zhang, Jinsuo; Mariani, R. D.; Unal, Cetin

    2015-12-01

    For liquid-sodium-cooled fast nuclear reactor systems, it is crucial to understand the behavior of lanthanides and other potential fission products in liquid sodium or other liquid metal solutions such as liquid cesium-sodium. In this study, we focus on lanthanide behavior in liquid sodium. Using ab initio molecular dynamics, we found that the solubility of cerium in liquid sodium at 1000 K was less than 0.78 at. %, and the diffusion coefficient of cerium in liquid sodium was calculated to be 5.57 × 10-9 m2/s. Furthermore, it was found that cerium in small amounts may significantly alter the heat capacity of the liquid sodium system. Our results are consistent with the experimental results for similar materials under similar conditions.

  13. Crystallization behavior of electroless Co-Ni-B alloy plated in magnetic field in presence of cerium

    Institute of Scientific and Technical Information of China (English)

    XUAN Tian-peng; ZHANG Lei; HUANG Qin-hua

    2006-01-01

    The electrochemical property, chemical composition and crystal structure of electroless Co-Ni-B-Ce alloy plated in general state as well as in magnetic field were studied using potentiometer, plasma emission spectrometer, X-ray diffractometer,transmission electron microscope. The results show that the static potential and polarizability of electroless Co-Ni-B alloy are remarkably improved as the plating is carried out in magnetic field in the presence of a little amount of cerium in plating bath.Because of the action of magnetic field and rare earth element cerium, the boron content in alloy decreases, while cobalt and nickel contents increase. As a result, the amorphous Co-Ni-B alloy transforms to the microcrystalline Co-Ni-B-Ce alloy when the plating is in general state, and the Co-Ni-B alloy makes a crystalline transformation because of the action of magnetic field and rare earth element cerium.

  14. Implementation of a complex multi-phase equation of state for cerium and its correlation with experiment

    Energy Technology Data Exchange (ETDEWEB)

    Cherne, Frank J [Los Alamos National Laboratory; Jensen, Brian J [Los Alamos National Laboratory; Elkin, Vyacheslav M [VNIITF

    2009-01-01

    The complexity of cerium combined with its interesting material properties makes it a desirable material to examine dynamically. Characteristics such as the softening of the material before the phase change, low pressure solid-solid phase change, predicted low pressure melt boundary, and the solid-solid critical point add complexity to the construction of its equation of state. Currently, we are incorporating a feedback loop between a theoretical understanding of the material and an experimental understanding. Using a model equation of state for cerium we compare calculated wave profiles with experimental wave profiles for a number of front surface impact (cerium impacting a plated window) experiments. Using the calculated release isentrope we predict the temperature of the observed rarefaction shock. These experiments showed that the release state occurs at different magnitudes, thus allowing us to infer where dynamic {gamma} - {alpha} phase boundary is.

  15. An application of secondary ion mass spectrometry (SIMS) in studies of internal contamination micro localization of cerium

    International Nuclear Information System (INIS)

    Secondary Ion Mass Spectrometry (SIMS) permits the detection of stable and radioactive elements in micro volume. Based on the ablation of specimens by ion bombardment, this mass spectrometry method allows a rapid assessment of trace elements in biological samples. Its resolving mass power provides an efficient analytical method and, in particular, it makes possible accurate isotopic ratio determination. In this work, a particular example is presented on the basis of results obtained as a result of analyses of duodenal tissue sections from rats contaminated with cerium. Tests were performed with SIMS to localize cerium in tissue sections obtained from rats 12, 24 and 48 hours after contamination with this element. In all specimens groups, cerium was found in apical region of micro villus, with the exception of those obtained 48 h after contamination. In this report, strengths and limitations of SIMS are pointed out as well as the potential of SIMS in biological research. (author)

  16. Corrosion resistance of flaky aluminum pigment coated with cerium oxides/hydroxides in chloride and acidic electrolytes

    Science.gov (United States)

    Niroumandrad, S.; Rostami, M.; Ramezanzadeh, B.

    2015-12-01

    The objective of this study was to enhance the corrosion resistance of lamellar aluminum pigment through surface treatment by cerium oxides/hydroxides. The surface composition of the pigments was studied by energy-dispersive spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS). The corrosion resistance of the pigment was evaluated by conventional hydrogen evolution measurements in acidic solution and electrochemical impedance spectroscopy (EIS) in 3.5% NaCl solution. Results showed that the Ce-rich coating composed of Ce2O3 and CeO2 was precipitated on the pigment surface after immersion in the cerium solution. The corrosion resistance of pigment was significantly enhanced after modification with cerium layer.

  17. Catalytic activity of cerium-doped Ru/Al2O3 during ozonation of dimethyl phthalate

    Institute of Scientific and Technical Information of China (English)

    Yunrui ZHOU; Wanpeng ZHU; Xun CHEN

    2008-01-01

    In this paper, factors influencing the mineraliza-tion of dimethyl phthalate (DMP) during catalytic ozona-tion with a cerium-doped Ru/Al2O3 catalyst were studied. The catalytic contribution was calculated through the results of a companrison experiment. It showed that doping cerium significantly enhanced catalytic activity. The total organic carbon (TOC) removal over the doped catalyst at 100 rain reached 75.1%, 61.3% using Ru/Al2O3 catalyst and only 14.0% using ozone alone. Catalytic activity reached the maximum when 0.2% of ruthenium and 1.0% of cerium'were simultaneously loaded onto Al2O3 support. Results of experiments on oxidation by ozone alone, adsorption of the catalyst, Ce ion's and heterogeneous catalytic ozonation confirmed that the contribution of het-erogeneous catalytic ozonation was about 50%, which showed the obvious effect of Ru-Ce/Al2O3 on catalytic activity.

  18. Circulating microRNA-126 in patients with coronary artery disease: correlation with LDL cholesterol

    Directory of Open Access Journals (Sweden)

    Sun Xiao

    2012-08-01

    Full Text Available Abstract Background Coronary artery disease (CAD is a major problem worldwide. Atherosclerosis and thrombosis underlying CAD involve multiple cell types. New and useful diagnostic markers are required. MicroRNAs (miRNAs are a class of noncoding RNAs that posttranscriptionally regulate the gene expressions involved in various cellular processes. Endothelial dysfunction is implicated in early processes of athero-thrombosis. Thus, it was hypothesized that the level of vascular endothelium-enriched miRNAs would be altered in plasma samples of CAD patients. Methods Vascular endothelium-enriched miRNA (miR-126 level was analyzed in plasma from 31 patients with CAD and 36 patients without CAD (qRT-PCR analysis. Results MiR-126 was not significantly down-regulated or up-regulated in CAD patients. Interestingly, the level of miR-126 was significantly decreased in patients with CAD and high low-density lipoprotein (LDL cholesterol level. In contrast, the level of miR-126 was significantly increased when LDL cholesterol was high in patients who had risk factors for CAD but did not have angiographically significant CAD. Conclusion MiR-126 was not significantly down-regulated or up-regulated in CAD patients and was not suitable for discriminating CAD patients from patients without CAD. The oppositely-directed relationship between miR-126 and LDL cholesterol in patients with or without CAD may have significant implications for identifying a potential role of miR-126 in cholesterol metabolism.

  19. Microstructure and mechanical properties of the Al-Ti alloy with cerium addition

    Directory of Open Access Journals (Sweden)

    L.A. Dobrzański

    2009-12-01

    Full Text Available Purpose: In this work there are presented the investigation results of mechanical properties and microstructure concerning mainly intermetallic phases of the aluminium – titanium alloy with a defined content of 2 and 4 % of cerium addition. The purpose of this work was also to determine the heat treatment conditions for solution heat treatment of the investigation alloys.Design/methodology/approach: The reason of this work was to determine the heat treatment influence, particularly solution heat treatment time to the changes of the microstructure, as well to determine which intermetallic phases occur after the heat treatment performed, and how is the morphology of these particles.Findings: After solution heat treatment for 4 hours the structure changes. The grains are larger and no more uniform as showed before. The most stable intermetallic in the Al-Ti system is the Al3Ti phase. The solution heat treatment time should be greater than 4 hours to ensure a proper solution of titanium and cerium in the Al-α solid solution.Research limitations/implications: The investigated aluminium samples were examined metallographically using optical microscope with different image techniques, scanning electron microscope and also analyzed using a Vickers micro-hardness tester, also EDS microanalysis was made.Practical implications: As an implication for the practice a new alloy can be developed, some other investigation should be performed in the future, but the knowledge found in this research shows an interesting investigation direction.Originality/value: The combination of light weight and high strength Ti-based alloys is very attractive for aerospace and automotive industries. Furthermore, the presence of calcium cerium into existence new unknown phases as well can enhance the thermal stability of ternary Al-Ti-Ce alloy because of its higher melting point then Al-Ti.

  20. Adsorption of arsenate and arsenite from aqueous solutions by cerium-loaded cation exchange resin

    Institute of Scientific and Technical Information of China (English)

    HE Zongliang; TIAN Senlin; NING Ping

    2012-01-01

    The removal of arsenic from water and wastewater is obligatory.Resin is one of the most effective adsorbents for the removal of arsenic.In order to improve the adsorption capacity of resin,a new cerium-loaded cation exchange resin arsenic adsorbent was prepared by impregnating cerium into the cation exchange resin.Batch adsorption experiments under various conditions,such as time,temperature,pH and with coexisting ions were carried out to evaluate the adsorption characteristics of cerium-loaded resin in the removal of As(Ⅴ) and As(Ⅲ) from aqueous solutions.The results showed that the adsorption kinetics of As(Ⅴ) and As(Ⅲ) obeyed a pseudo second-order kinetic model and the adsorption rate constants were 0.3159 and 0.5215 g·mg-1·min-1,respectively.The adsorption of As(Ⅴ) followed the Freundlich adsorption isotherm model and the adsorption isotherm data for As(Ⅲ) fitted well to the Langmuir equation model.The adsorption capacities were 1.0278 mg/g for As(Ⅴ) and 2.5297 mg/g for As(Ⅲ).Both the adsorption of As(Ⅴ) and As(Ⅲ) were found to be pH sensitive and the optimum pH was found to be 5-6.Except for the phosphate ion,the coexisting anionics,such as nitrate,chlorate,sulphate and carbonate,showed no remarkable effect on AS(Ⅴ) and As(Ⅲ) adsorption.The desorption and regeneration study showed that the adsorption capacity of Ce-loaded resin for As(Ⅴ) and As(Ⅲ) could be restored to 97.80% and 69.61%,respectively,using 0.5 mol/L sodium hydroxide solution.

  1. High temperature stability of a 316 austenitic stainless steel coated with cerium oxide nanoparticles

    Science.gov (United States)

    Mendoza Del Angel, Humberto

    Cerium oxide (CeO2-x) nanoparticles were used for coating protection on a 316 Austenitic Stainless Steel (Aust. SS) to enhance the thermal stability of the oxide films formed at high temperatures. Three simple coating methods were used, dipping, spraying and spinning in order to explore the coating film morphology, nanoparticle distribution and its effect on thermal stability of the steel substrates. Experimentally, the selected steel was exposed to 800°C/1000°C under dry air conditions. Weight changes (DeltaW/A) were monitored as a function of time and the results were compared with uncoated alloys tested under similar conditions. The cerium oxide nanoparticles used on the three methods were synthesized in the laboratory obtaining nanoparticles in the range of 3.5 to 6.2 nanometers. It was found that cerium oxide particle size is affected by temperature. In this case, the activation energy for particle growth was estimated to be around 21,1 kJ/mol. Characterization of the film morphologies before and after oxidation were carried out using Atomic Force Microscopy (AFM), Surface Profilometry, Scanning Electron Microscopy (SEM) and X-ray Diffraction (XRD). A comparison of the three coating methods was carried out for the particular case of the 316 Aust. SS coupons. In addition, the oxidation kinetics was experimentally investigated for the coated samples. For this purpose thermal gravimetric determinations were made at 800°C, 900°C, and 1000°C and oxidation rate constants were calculated at each temperature.

  2. Catalytic wet peroxidation of pyridine bearing wastewater by cerium supported SBA-15

    Energy Technology Data Exchange (ETDEWEB)

    Subbaramaiah, V. [Department of Chemical Engineering, Indian Institute of Technology Roorkee, Roorkee 247667 Uttarakhand (India); Srivastava, Vimal Chandra, E-mail: vimalcsr@yahoo.co.in [Department of Chemical Engineering, Indian Institute of Technology Roorkee, Roorkee 247667 Uttarakhand (India); Mall, Indra Deo [Department of Chemical Engineering, Indian Institute of Technology Roorkee, Roorkee 247667 Uttarakhand (India)

    2013-03-15

    Highlights: ► Cerium supported SBA-15 (Ce/SBA-15) synthesized by two-step synthesis. ► Characterization of Ce/SBA-15 by FTIR, XRD and BET surface area. ► Catalytic peroxidation of pyridine by Ce/SBA-15. ► Optimization of parameters like catalyst dose, H{sub 2}O{sub 2} dose, initial concentration and temperature. ► Catalyst reusability and leaching study performed. -- Abstract: Cerium supported SBA-15 (Ce/SBA-15) was synthesized by two-step synthesis method in acidic medium. It was further characterized by various characterization techniques such as X-ray diffraction, field-emission scanning electron microscopy, Fourier transform infrared spectroscopy and N{sub 2} adsorption–desorption pore size distribution analysis. The Ce/SBA-15 showed highly ordered meso-structure with pore diameter ≈ 70–100 A and pore volume ≈ 0.025 cm{sup 3}/g. Ce/SBA-15 was further evaluated as a catalyst for the oxidation of highly toxic and non-biodegradable material, pyridine, by catalytic wet-peroxidation method. The effects of various operating parameters such as catalyst dose (0.5–6 g/l), stoichiometric ratio of H{sub 2}O{sub 2}/pyridine (1–6), initial pyridine concentration (50–800 mg/l) and temperature (313–358 K) have been evaluated and optimized. Ce/SBA-15 showed stable performance during reuse for six cycles with negligible cerium leaching. Kinetic and thermodynamic parameters and operation cost have also been determined.

  3. Changes in Physiological and Agronomical Parameters of Barley (Hordeum vulgare) Exposed to Cerium and Titanium Dioxide Nanoparticles

    OpenAIRE

    Luca Marchiol; Alessandro Mattiello; Filip Pošćić; Guido Fellet; Costanza Zavalloni; Elvio Carlino; Rita Musetti

    2016-01-01

    The aims of our experiment were to evaluate the uptake and translocation of cerium and titanium oxide nanoparticles and to verify their effects on the growth cycle of barley (Hordeum vulgare L.). Barley plants were grown to physiological maturity in soil enriched with either 0, 500 or 1000 mg·kg−1 cerium oxide nanoparticles (nCeO2) or titanium oxide nanoparticles (nTiO2) and their combination. The growth cycle of nCeO2 and nTiO2 treated plants was about 10 days longer than the controls. In nC...

  4. Biosorption of lanthanum and cerium from aqueous solutions using tangerine (Citrus reticulata) peel: Equilibrium, kinetic, and thermodynamic studies

    OpenAIRE

    Torab-Mostaedi Meisam

    2013-01-01

    Biosorption of lanthanum (III) and cerium (III) from aqueous solution by tangerine (Citrus reticulate) peel has been investigated in a batch system as a function of pH, biosorbent dosage, contact time, and temperature. The equilibrium pH was found to severely affect the biosorption performance; pH 5.0 is found to be an optimum pH for favorable biosorption of La (III) and Ce (III). The biosorption of lanthanum and cerium was investigated by the Langmuir, Freundlich and Dubinin-Radushkevi...

  5. Iranian natural clinoptilolite and its synthetic zeolite P for removal of cerium and thorium from nuclear wastewaters

    International Nuclear Information System (INIS)

    The ion-exchange behaviors of an Iranian natural clinoptilolite and its modified forms as well as a relevant synthetic zeolite P were investigated toward cerium and thorium from nuclear wastewaters. Column experiments were performed on different exchangers in various conditions and the effect of parameters such as particle size, pH, temperature, and time were considered. The distribution coefficient, cation exchange capacity and some thermodynamic parameters were calculated. Ion-exchange isotherms and break-through curves were plotted. As a result, the selectivity of synthetic zeolite P from Iranian natural clinoptilolite toward cerium and thorium was compared with that of natural and cationic forms of clinoptilolite. (author)

  6. In situ growth of blue-emitting thin films of cerium-doped barium chloride hydrate at low temperatures

    OpenAIRE

    J. Hao; LOU, Z; Cocivera, M

    2003-01-01

    Blue emission was observed from thin films of barium chloride hydrate doped with cerium. The films were deposited by spray pyrolysis of aqueous solutions with substrate temperatures between 250 and 450°C. The cathodoluminescence (CL) spectrum consists of two peaks at 443 and 485 nm due to 4f-5d transitions of cerium ion. The dependence of the emission band on deposition temperature and Ce/Ba ratio is discussed. The CL luminance and luminous efficiency at 5 kV were 120 cd/m² and 0.48 lm/W, res...

  7. Improvement of corrosion resistance of AZ31 Mg alloy by anodizing with co-precipitation of cerium oxide

    Institute of Scientific and Technical Information of China (English)

    Salah Abdelghany SALMAN; Ryoichi ICHINO; Masazumi OKIDO

    2009-01-01

    Anodizing of AZ31 Mg alloy in NaOH solution by co-precipitation of cerium oxide was investigated. The chemical composition and phase structure of the coating film were determined via optical microscopy, SEM and XRD. The corrosion properties of the anodic film were characterized by using potentiodynamic polarization curves in 17 mmol/L NaCl and 0.1 mol/L Na2SO4 solution at 298 K. The corrosion resistance of AZ31 magnesium alloy is significantly improved by adding cerium oxide to alkaline solution. In addition, the surface properties are enhanced and the film contains no crack.

  8. APPLICATIONS OF CERIUM BIS (MONOMYRISTY—LPHOSPHATE)ADSORBENT TO REVERSED PHASE LIQUID CHROMATOGRAPHY

    Institute of Scientific and Technical Information of China (English)

    SuZhengquan; FengHuixia; 等

    1996-01-01

    The tetravalent metal salts of monoalkyl phosphates [M(O3POR)2]are a new kind of stationary phases of Chromatography-homogeneous bonded phases.This paper deals with the application of cerium bis(monomyristylphosphate)as support to reversed phase liquid chromatography.The results show that the best mobil phase is CH3CN:H2O=95:5.The good separation to the mixture containing six aromatic hydrocarbons and the determination of naphthalene in a group samples have been achieved.The regression analysis shows that detect limits,linearities and precision for six aromatic hydrocarbons are good.

  9. Trace electrochemical analysis of Europium, Ytterbium, and Cerium at their joint presence in solution

    Directory of Open Access Journals (Sweden)

    Rema Matakova

    2012-03-01

    Full Text Available In the course of several decades at the department of analytical chemistry and chemistry of rare elements there were studied the electrode processes with participation of rare-earth metals (REM in accordance with the long awaiting problem of the development of rare-metal and rare-earth branch of non-ferrous metallurgy of Kazakhstan. With the aim of express and highly sensitive analytical control of raw materials and final product of rare-earth industry there were developed the methods of inversion-voltamperometric determination of low concentrations of europium, ytterbium and cerium under the conditions of their individual and combined presence in the solution.

  10. The low-aluminium cast iron of reduced silicon content treated with cerium mischmetal

    OpenAIRE

    M. S. Soiński; P. Susek; Hübner, K.; P. Mierzwa

    2008-01-01

    The work presents the effect of cerium mischmetal used in quantities of 0.1 and 0.2 wt-% and ferrosilicon used in quantities from 0.5% to 1.5% on the alloy matrix and the shape of graphite precipitates in the low-aluminium cast iron from seven heats, basing on the examination of its structure. The hypereutectic cast iron of the relatively high carbon content (4.0÷4.2%) at the prior-to-treatment silicon and manganese content equal to ca. 0.6% and ca. 0.04%, respectively, has been examined.It h...

  11. Relationship between surface area and crystal size of pure and doped cerium oxides

    Institute of Scientific and Technical Information of China (English)

    C.; Bueno-Ferrer; S.; Parres-Esclapez; D.; Lozano-Castelló; A.; Bueno-López

    2010-01-01

    Pure and Zr, La or Pr-doped cerium oxides were characterised by transmission electron microscopy (TEM), N2 adsorption-desorption at -196 oC and X-ray diffraction (XRD). For crystal sizes calculation, the Scherrer and Williamson-Hall equations were compared, and the relationship between surface area and crystal size was critically discussed. It was demonstrated that the Williamson-Hall equation must be used instead of the Scherrer equation to calculate crystal sizes, since the latter equation underestimated ...

  12. Surface structures of cerium oxide nanocrystalline particles from the size dependence of the lattice parameters

    Science.gov (United States)

    Tsunekawa, S.; Ito, S.; Kawazoe, Y.

    2004-10-01

    Cerium oxide nanocrystalline particles are synthesized and monodispersed in the size range from 2 to 8nm in diameter. The dependence of the lattice parameters on particle size is obtained by x-ray and electron diffraction analyses. The size dependence well coincides with the estimation based on the assumption that the surface is composed of one layer of Ce2O3 and the inside consists of CeO2. The effect of particle size on lattice parameters is discussed from the differences in the fabrication method and the surface structure.

  13. Performance of a Tungsten-Cerium Fluoride Sampling Calorimeter in High-Energy Electron Beam Tests

    CERN Document Server

    Becker, R; Dissertori, G; Djambazov, L; Donegà, M; Lustermann, W; Marini, A C; Nessi-Tedaldi, F; Pandolfi, F; Peruzzi, M; Schönenberger, M; Cavallari, F; Dafinei, I; Diemoz, M; Lope, C Jorda; Meridiani, P; Nuccetelli, M; Paramatti, R; Pellegrino, F; Micheli, F; Organtini, G; Rahatlou, S; Soffi, L; Brianza, L; Govoni, P; Martelli, A; de Fatis, T Tabarelli; Monti, V; Pastrone, N; Trapani, P P; Candelise, V; Della Ricca, G

    2015-01-01

    A prototype for a sampling calorimeter made out of cerium fluoride crystals interleaved with tungsten plates, and read out by wavelength-shifting fibres, has been exposed to beams of electrons with energies between 20 and 150 GeV, produced by the CERN Super Proton Synchrotron accelerator complex. The performance of the prototype is presented and compared to that of a Geant4 simulation of the apparatus. Particular emphasis is given to the response uniformity across the channel front face, and to the prototype's energy resolution.

  14. Preparation and electrochemical study of cerium-silica sol-gel thin films

    International Nuclear Information System (INIS)

    Design and development of suitable multilayered systems for delaying corrosion advance in metals requires that both the alteration mechanisms of the metal and the behaviour and properties of the protective coatings be known. Coatings prepared by the sol-gel method provide a good approach as protective layers on metallic surfaces. This kind of coatings can be prepared from pure chemical reagents at room temperature and atmospheric pressure, with compositions in a very wide range of environmentally non-aggressive precursors. Sol-gel coatings based on siloxane bonded units were prepared starting from an organic-inorganic hybrid system. The precursors were γ-methacryloxypropyltrimethoxysilane (MAP) and tetramethoxysilane (TMOS). Cerium nitrate hexahydrate in three different concentrations was added. Cerium salts may perform a similar protective effect to that carried out by the well-known lead oxides and chromium salts, even though in this case a negative environmental impact is not expected. Application of coatings upon pure zinc substrates and common glass slides were performed by spinning. Coated samples were heat treated at 40 deg. C for 6 days. Optical measurements (UV-Vis absorption and diffuse reflectance spectroscopies) pointed out that the coatings were colourless and transparent, reducing the diffuse reflectance of the metallic surface up to ∼60%. Optical and scanning electron microscopies (SEM) allowed observation of the texture and microstructure of the coated samples, both before and after the corrosion tests were carried out. Likewise, the remaining sols were kept to gelify at 60 deg. C for 4 days and then powdered to obtain suitable samples for analysing them by other characterisation techniques (Fourier transformed infrared, FTIR and differential thermal analysis, DTA). Electrochemical measurements were performed by impedance spectroscopy. This technique was used to clarify the anticorrosive protection role of cerium ions incorporated into the hybrid

  15. Sequence-specific Hydrolysis of Single-stranded DNA by PNA-Cerium (Ⅳ) Adduct

    Institute of Scientific and Technical Information of China (English)

    He Bai SHEN; Feng WANG; Yong Tao YANG

    2005-01-01

    A novel artificial site specific cleavage reagent, with peptide nucleic acid (PNA) as sequence-recognizing moiety and cerium (Ⅳ) ions as "scissors" for cleaving target DNA, was synthesized. Subsequently, it was employed in the cleavage of target 26-mer single-stranded DNA (ssDNA), which has 10-mer sequence complementary with PNA recognizer in the hybrids,under physiological conditions. Reversed-phase high-performance liquid chromatogram (RPHPLC) experiments indicated that the artificial site specific cleavage reagent could cleave the target DNA specifically.

  16. β Coronae Bolealis: Lithium and Cerium Contribution to the Blend at 6708 Å

    Science.gov (United States)

    Drake, N. A.; Hubrig, S.; Polosukhina, N. S.; de La Reza, R.

    2006-06-01

    We analyze the Li I 6708 Å spectral region of the chemically peculiar Ap star βCrB using high resolution, high signal-to-noise spectra obtained at different rotation phases. Our study shows that the Ce II line at 6708.099 Å is a main contributor to the spectral feature at 6708 Å. This fact explains the observed red shift of the Li I doublet of about 0.2 Å found by Hack et al. (1997). We derive the values of lithium and cerium abundances for different rotation phases and show that βCrB has ``cosmic'' Li abundance.

  17. Kinetic spectrophotometric method for the determination of cerium(Ⅳ) with naphthol green B

    Institute of Scientific and Technical Information of China (English)

    LIU Yuying; WANG Ping

    2009-01-01

    A simple and sensitive spectrophotometric method was described for the determination of cerium(Ⅳ) based on its catalytic effect on the oxidation of naphthol green B by potassium periodate in the medium of sulfuric acid. The influences of acidity, concentration of reactants, reaction time, reaction temperature, and foreign ions were discussed, and the optimum reaction conditions were established. The reaction was monitored spectrophotometrically by measuring the decrease in absorbance of naphthol green B at 710 nm after a fixed time (8 min). The separation. Recovery experiments were also performed, and the recovery was between 95.7%-111.0%.

  18. UV-Shielding and Catalytic Characteristics of Nanoscale Zinc-Cerium Oxides

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Fine particles of zinc-cerium oxides (ZCO) used as an ultraviolet filter were prepared via combustion synthesis route. The catalytic activity, UV-shielding performance, surface modification and application of ZCO in polyester varnish were discussed in detail. The experimental results indicate that the photo-catalytic activity of ZCO is much smaller than these of ZnO and TiO2; the oxidation catalytic activity of ZCO is far lower than that of CeO2; the ZCO has shown excellent ultraviolet absorption in the range of UV;addition modified ZCO (MZCO) into polyester will enhance the UV-shielding capability of polyester.

  19. Acetylcholinesterase triggers the aggregation of PrP 106-126

    International Nuclear Information System (INIS)

    Acetylcholinesterase (AChE), a senile plaque component, promotes amyloid-β-protein (Aβ) fibril formation in vitro. The presence of prion protein (PrP) in Alzheimer's disease (AD) senile plaques prompted us to assess if AChE could trigger the PrP peptides aggregation as well. Consequently, the efficacy of AChE on the PrP peptide spanning-residues 106-126 aggregation containing a coumarin fluorescence probe (coumarin-PrP 106-126) was studied. Kinetics of coumarin-PrP 106-126 aggregation showed a significant increase of maximum size of aggregates (MSA), which was dependent on AChE concentration. AChE-PrP 106-126 aggregates showed the tinctorial and optical amyloid properties as determined by polarized light and electronic microscopy analysis. A remarkable inhibition of MSA was obtained with propidium iodide, suggesting that AChE triggers PrP 106-126 and Aβ aggregation through a similar mechanism. Huprines (AChE inhibitors) also significantly decreased MSA induced by AChE as well, unveiling the potential interest for some AChE inhibitors as a novel class of potential anti-prion drugs

  20. Influence of PrP 106 - 126 on expression of laminin and fibronectin in astrocyte

    Institute of Scientific and Technical Information of China (English)

    LI YuRong; GUAN LeLuo; YANG JianMin; ZHOU XiangMei; YIN XiaoMin; ZHAO DeMing

    2008-01-01

    Astrogliosis is a hallmark of prion disease, but the metabolic alterations of astrocytes remain poorly documented. A synthetic pepUde corresponding to amino acid 106-126 of the human prion protein (PrP) has been shown to be toxic to neurons. In this study, the effects of PrP 106-126 on astrocytes were investigated in vitro. The proliferation of astrocytes was significantly (P < 0.05) increased when grown in media conditioned with PrP 106-126 (80 μmol/L) from microglia. The expression of laminin (LN) and fibronectin (FN) was examined at both mRNA and protein levels. The results showed that ex-posure of astrocytes to PrP 106-126 enhanced the expression of LN and FN. The increase of FN in astrocyte cultures required cytokines previously released by activated microglia. This study reveals the expression ofLN and FN affected by PrP106-126.

  1. Zinc, copper, and carnosine attenuate neurotoxicity of prion fragment PrP106-126.

    Science.gov (United States)

    Kawahara, Masahiro; Koyama, Hironari; Nagata, Tetsuya; Sadakane, Yutaka

    2011-07-01

    Prion diseases are progressive neurodegenerative diseases that are associated with the conversion of normal cellular prion protein (PrP(C)) to abnormal pathogenic prion protein (PrP(SC)) by conformational changes. Prion protein is a metal-binding protein that is suggested to be involved in metal homeostasis. We investigated here the effects of trace elements on the conformational changes and neurotoxicity of synthetic prion peptide (PrP106-126). PrP106-126 exhibited the formation of β-sheet structures and enhanced neurotoxicity during the aging process. The co-existence of Zn(2+) or Cu(2+) during aging inhibited β-sheet formation by PrP106-126 and attenuated its neurotoxicity on primary cultured rat hippocampal neurons. Although PrP106-126 formed amyloid-like fibrils as observed by atomic force microscopy, the height of the fibers was decreased in the presence of Zn(2+) or Cu(2+). Carnosine (β-alanyl histidine) significantly inhibited both the β-sheet formation and the neurotoxicity of PrP106-126. Our results suggested that Zn(2+) and Cu(2+) might be involved in the pathogenesis of prion diseases. It is also possible that carnosine might become a candidate for therapeutic treatments for prion diseases. PMID:21442127

  2. Absolute activity measurement and gamma-ray emission probability for decay of I-126

    International Nuclear Information System (INIS)

    The accurate knowledge of the gamma-ray emission probability per decay of radionuclides is important in several applications. In the case of 126 I, its importance lies mainly in fast neutron dosimetry as well as in the production of 125 I where 126 I appears as an impurity. In the present work the gamma-ray emission probabilities per decay for the 388 and 666-KeV transitions of 126 I have been measured. This radionuclide was obtained by means of the 127 I(n, 2n)126 I reaction in a fast neutron flux at the IPEN 2 MW research reactor. The methodology for the primary standardization of 126 I is described. For this purpose, two different coincidence systems were used due to the complex decay scheme of this radionuclide. The βbranch measurement was carried out in a 4 π(PC)β-γ coincidence system consisting of a proportional counter, coupled to a pair of 3'x3' Na I (Tl) crystal. The electron capture branch was measured in a X-γ coincidence system using two NaI(Tl) crystals. The gamma-ray measurements were performed in a HPGe system, previously calibrated by means of standard sources supplied by the International Atomic Energy Agency. All the uncertainties evolved were treated rigorously, by means of covariance analysis. (author)

  3. 126例小儿肾综合征出血热临床分析%Clinical analysis of 126 children with hemorrhagic fever with renal syndrome

    Institute of Scientific and Technical Information of China (English)

    吴翠萍; 李汝勇; 郄良毅; 夏德全

    2003-01-01

    @@ 我院自1991年1月~2001年12月共收治肾综合征出血热(Hemorrhagic Fever with Renal Syndrome, HFRS)患者2 536例,其中14岁以下患儿126例,我们对其临床资料进行回顾性分析,以探讨小儿HFRS临床特点,供临床医师借鉴.

  4. Signature of the N=126 shell closure in dwell times of alpha-particle tunneling

    CERN Document Server

    Kelkar, N G

    2016-01-01

    Characteristic quantities such as the penetration and preformation probabilities, assault frequency and tunneling times in the tunneling description of alpha decay of heavy nuclei are explored to reveal their sensitivity to neutron numbers in the vicinity of the magic neutron number $N$ = 126. Using realistic nuclear potentials, the sensitivity of these quantities to the parameters of the theoretical approach is also tested. An investigation of the region from $N=116$ to $N=132$ in Po nuclei reveals that the tunneling $\\alpha$ particle spends the least amount of time with an $N=126$ magic daughter nucleus. The shell closure at $N=126$ seems to affect the behaviour of the dwell times of the tunneling alpha particles and this occurs through the influence of the $Q$-values involved.

  5. Signature of the N = 126 shell closure in dwell times of alpha-particle tunneling

    Science.gov (United States)

    Kelkar, N. G.; Nowakowski, M.

    2016-10-01

    Characteristic quantities such as the penetration and preformation probabilities, assault frequency and tunneling times in the tunneling description of alpha decay of heavy nuclei are explored to reveal their sensitivity to neutron numbers in the vicinity of the magic neutron number N = 126. Using realistic nuclear potentials, the sensitivity of these quantities to the parameters of the theoretical approach is also tested. An investigation of the region from N = 116 to N = 132 in Po nuclei reveals that the tunneling α particle spends the least amount of time with an N = 126 magic daughter nucleus. The shell closure at N = 126 seems to affect the behavior of the dwell times of the tunneling alpha particles and this occurs through the influence of the Q-values involved.

  6. Potential role of microRNA-126 in the diagnosis of cancers

    Science.gov (United States)

    Yan, Jin; Ma, Shijie; Zhang, Yifeng; Yin, Chengqiang; Zhou, Xiaoying; Zhang, Guoxin

    2016-01-01

    Abstract Background: Cancer has become a major public concern all over the world and early diagnosis of cancer is of great benefit for treatment and prognosis. Several studies have investigated the association between abnormal circulating microRNA-126 (miR-126) expression and the risk of various cancers, but the results are inconsistent. Therefore, this meta-analysis was carried out to assess the potential diagnostic value of miR-126 for cancer. Methods: Relevant studies were searched from PubMed, Embase, and Web of Science and we calculated the pooled sensitivity, specificity, positive likelihood ratio (PLR), negative likelihood ratio (NLR), diagnostic odds ratio (DOR), and area under the summary receiver operator characteristic curve (AUC) to assess the diagnostic value of miR-126 for cancer detection. Results: A total of 745 cancer patients and 749 controls from 11 studies of 7 papers were included in this meta-analysis. The summary estimates revealed that the pooled sensitivity was 68% (95% confidence interval [CI]: 60–75%), the specificity was 76% (95% CI: 65–85%), the PLR was 2.87 (95% CI: 1.96–4.21), the NLR was 0.42 (95% CI: 0.35–0.52), the DOR was 7 (95% CI: 4–11), and the AUC was 0.77 (95%CI: 0.73–0.80). Moreover, the sample type, cancer type, sample size, and quality score might be sources of heterogeneity. Conclusion: This systematic review and meta-analysis suggests that miR-126 has great potential to be a noninvasive biomarker in the diagnosis of cancer. However, more well-designed studies with larger sample size on the diagnostic value of miR-126 for cancer are needed in the future. PMID:27583885

  7. Genetic and Protein Analysis of Betadefensin 126 and Association with Success Rate of Intrauterin Insemination

    Directory of Open Access Journals (Sweden)

    Mahdeye Hassani

    2015-04-01

    Full Text Available Introduction: Human β-defensin 126 (DEFB126 is a small cationic glycoprotein that is considered as an important component of the primates and human sperm glycocalix. It protects sperm from infection-causing microbes and against the female immune system antibodies. Human DEFB126 gene is located on the sub-telomeric region of 20p13. DEFB126 variations caused by a frame shift deletion of two cytosines was found to affect the sperms functionality. The aim of this study was to verify the correlation of this gene mutation with success rate of IUI. Methods: In the present study, the rate of DEFB126 gene mutation was elucidated in 76 Iranian men with unexplained infertility whose wives had undergone IUI with either positive or negative results. DNA properties quantified with NanoDrop spectrophotometers. Standard PCR, Single-strand conformation polymorphism (SSCP and sequencing were used to confirm the results. Moreover,immunocytochemistry was performed for the assessment of the protein expression on sperm cells. Results: DNA quantification revealed that 24.4% of men, whose wives showed a negative result for IUI, were homozygote for this mutation, whereas none of the couples with a positive IUI result carried the mutation for this gene (P≤0.05. Moreover, the amount of this protein was decreased on the sperms of men who carried the mutant allele. Conclusion: Results of the present study suggested that common alteration in DEFB126 gene could be considered as a critical factor in the success rate of IUI operation.

  8. Characterization of microstructure and catalytic of cerium oxide obtained by colloidal solution; Caracterizacao da microestrutura e da atividade catalitica de oxido de cerio obtido por solucao coloidal

    Energy Technology Data Exchange (ETDEWEB)

    Senisse, C.A.L.; Bergmann, C.P.; Alves, A.K., E-mail: carolinasenisse@hotmail.com [Universidade Federal do Rio Grande do Sul (UFRGS), Porto Alege, RS (Brazil). Lab. de Materiais Ceramicos

    2012-07-01

    This study investigated to obtain particles of cerium oxide, for use as catalysts for the combustion of methane using the technique of through polymeric colloidal solution. Obtaining the colloidal system is based on hydrolysis of salts such as cerium acetylacetonate, cerium nitrate in the presence of additives such as polyvinylbutyral (PVB), polyvinylpyrrolidone (PVP) and polyvinyl acetate (PVA), at concentrations of 5, 10 and 15% in aqueous or alcoholic medium. These solutions containing ions of interest were subjected to a heat treatment at 650° C for 30 minutes, with heating rate of 2 ° C/ min. After heat treatment, the fibers were characterized according to their morphology, surface area, crystallinity, weight loss and catalytic activity. Samples obtained from cerium acetylacetonate were more reactive than the cerium nitrate to the combustion of methane, as showed greater conversions and higher temperatures reached during the process, which is of utmost importance since the combustion catalytic methane is used for generating thermal energy. After the reaction with methane, the samples underwent significant change in surface area, probably due to the intensity of combustion reactions of the nitrate and the generation of heat involved in this reaction, which gave rise to coarse particles. During the combustion process using the obtained from particles of cerium acetylacetonate, there was the release of large quantities of nitrogen compared to the results of assays with the particles obtained with cerium nitrate. (author)

  9. Effect of cerium on structure modifications of a hybrid sol–gel coating, its mechanical properties and anti-corrosion behavior

    Energy Technology Data Exchange (ETDEWEB)

    Cambon, Jean-Baptiste, E-mail: cambon@chimie.ups-tlse.fr [Institut Carnot CIRIMAT, Université de Toulouse, UMR CNRS 5085, 118 Route de Narbonne, 31062 Toulouse Cedex 9 (France); Esteban, Julien; Ansart, Florence; Bonino, Jean-Pierre; Turq, Viviane [Institut Carnot CIRIMAT, Université de Toulouse, UMR CNRS 5085, 118 Route de Narbonne, 31062 Toulouse Cedex 9 (France); Santagneli, S.H.; Santilli, C.V.; Pulcinelli, S.H. [Departamento Fısico-Química, Instituto de Química, Universidade Estadual Paulista, UNESP, CP 355, 14801-970 Araraquara, SP (Brazil)

    2012-11-15

    Highlights: ► New sol–gel routes to replace chromates for corrosion protection of aluminum. ► Effect of cerium concentration on the microstructure of xerogel. ► Electrochemical and mechanical performances of hybrid coating with different cerium contents. ► Good correlation between the different results with an optimal cerium content of 0.01 M. -- Abstract: An organic–inorganic hybrid coating was developed to improve the corrosion resistance of the aluminum alloy AA 2024-T3. Organic and inorganic coatings derived from glycidoxypropyl-trimethoxysilane (GPTMS) and aluminum tri-sec-butoxide Al(O{sup s}Bu){sub 3}, with different cerium contents, were deposited onto aluminum by dip-coating process. Corrosion resistance and mechanical properties were investigated by electrochemical impedance measurements and nano-indentation respectively. An optimal cerium concentration of 0.01 M was evidenced. To correlate and explain the hybrid coating performances in relation to the cerium content, NMR experiments were performed. It has been shown that when the cerium concentration in the hybrid is higher than 0.01 M there are important modifications in the hybrid structure that account for the mechanical properties and anti-corrosion behavior of the sol–gel coating.

  10. Effects of cerium oxide supplementation to laying hen diets on performance, egg quality, some antioxidant enzymes in serum and lipid oxidation in egg yolk.

    Science.gov (United States)

    Bölükbaşı, S C; Al-Sagan, A A; Ürüşan, H; Erhan, M K; Durmuş, O; Kurt, N

    2016-08-01

    This study was conducted to determine the effects of dietary cerium oxide levels (0, 100, 200, 300 or 400 mg/kg) on the laying performance, egg quality, some blood serum parameters and egg lipid peroxidation of laying hen. In total, one hundred and twenty 22-week-old brown Lohman LSL laying hens were randomly assigned to five groups equally (n = 24). Each treatment was replicated six times. Dietary supplementation of cerium oxide had no significant effect on feed intake and egg weight. The addition of cerium oxide to the laying hens' feed improved feed conversion ratio and increased (p laying hens feed led to a significant (p hen diets. It was also observed that serum superoxide dismutase (SOD) activity and malondialdehyde (MDA) concentration decreased significantly with supplementation of cerium oxide in diets. Inclusion of cerium oxide resulted in a significant reduction in thiobarbituric acid reactive substance (TBARS) values in egg yolk in this study. It can be concluded that the addition of cerium oxide had positive effects on egg production, feed conversion ratio and egg shelf life. Based on the results of this study, it could be advised to supplement laying hens feed with cerium oxide as feed additives. PMID:26847677

  11. Cytogenetic Analysis on Wheat Female Sterile Line XND126%小麦雌性不育系XND126的细胞遗传学研究

    Institute of Scientific and Technical Information of China (English)

    杨文杰; 徐弘娇; 冯雪娇; 鲁媛媛; 窦秉德

    2011-01-01

    The research of wheat female sterile line was not only of important significance to the sex determination and phylogenesis mechanism of fertility in plant, but also of potential practical value to the utilization of heterosis. The mitosis of root tip cells was observed in wheat female sterile line XND126 and cultivar LiaochunlO, Longchun15 and Gaocheng 8901. The meiosis of pollen mother cell (PMC) was mainly analyzed in XND126, Fi hybrids from XND126 and 3 other parents. The result showed that the chromosome numbers in the somatic cells of the 4 parents were all 42. There were 2-6 mono-somes at meiotic metaphase I , 2 or more lagging chromosomes or chromosome bridges at meiotic anaphase I , one or multiple micronucleus at bispore and quartet in a small proportion of PMC respectively. The data suggested that there were abnormal homologous chromosomes pairing and chromosomal structural variation such as inversion in PMC of XND126. These data provided basic information to show the effect and mechanism of related genes or chromosome behavior in the phylogenesis of female or male fertility.%小麦(Triticum aestivum L.)雌性不育系的研究和选育,对认识植物的育性发生和性别决定机制具有重要的理论意义,对其杂种优势的研究和利用也具有潜在的实践价值.以小麦雌性不育系XND126及品种辽春10号、陇春15、藁城8901为试验材料,对其根尖细胞的有丝分裂过程进行了观察,重点对XND126及其所配的3个F1的花粉母细胞减数分裂过程进行了研究.结果显示,4个亲本体细胞中均含有42条染色体.雌性不育系及其杂种的小部分花粉母细胞在减数分裂的中期Ⅰ有2~6个单价体,后期则有染色体桥和落后染色体出现,二分体和四分体时期也观察到有微核的出现.表明XND126的少数同源染色体在减数分裂中配对异常,并可能存在倒位等染色体结构变异.该资料的获得,为进一步研究相关基因或染色体行为在雌

  12. The evolution mechanism of the dislocation loops in irradiated lanthanum doped cerium oxide

    Energy Technology Data Exchange (ETDEWEB)

    Miao, Yinbin, E-mail: miao2@illinois.edu [Department of Nuclear, Plasma and Radiological Engineering, University of Illinois at Urbana-Champaign, IL 61801 (United States); Aidhy, Dilpuneet [Materials Science and Technology Division, Oak Ridge National Laboratory, TN 37831 (United States); Chen, Wei-Ying; Mo, Kun; Oaks, Aaron [Department of Nuclear, Plasma and Radiological Engineering, University of Illinois at Urbana-Champaign, IL 61801 (United States); Wolf, Dieter [Material Science Division, Argonne National Laboratory, IL 60439 (United States); Stubbins, James F. [Department of Nuclear, Plasma and Radiological Engineering, University of Illinois at Urbana-Champaign, IL 61801 (United States)

    2014-02-01

    Cerium dioxide, a non-radioactive surrogate of uranium dioxide, is useful for simulating the radiation responses of uranium dioxide and mixed oxide fuel (MOX). Controlled additions of lanthanum can also be used to form various levels of lattice oxide or anion vacancies. In previous transmission electron microscopy (TEM) experimental studies, the growth rate of dislocation loops in irradiated lanthanum doped ceria was reported to vary with lanthanum concentration. This work reports findings of the evolution mechanisms of the dislocation loops in cerium oxide with and without lanthanum dopants based on a combination of molecular statics and molecular dynamics simulations. These dislocation loops are found to be b=1/3〈111〉 interstitial type Frank loops. Calculations of the defect energy profiles of the dislocation loops with different structural configurations and radii reveal the basis for preference of nucleation as well as the driving force of growth. Frenkel pair evolution simulations and displacement cascade overlaps simulations were conducted for a variety of lanthanum doping conditions. The nucleation and growth processes of the Frank loop were found to be controlled by the mobility of cation interstitials, which is significantly influenced by the lanthanum doping concentration. Competition mechanisms coupled with the mobility of cation point defects were discovered, and can be used to explain the lanthanum effects observed in experiments.

  13. The evolution mechanism of the dislocation loops in irradiated lanthanum doped cerium oxide

    Science.gov (United States)

    Miao, Yinbin; Aidhy, Dilpuneet; Chen, Wei-Ying; Mo, Kun; Oaks, Aaron; Wolf, Dieter; Stubbins, James F.

    2014-02-01

    Cerium dioxide, a non-radioactive surrogate of uranium dioxide, is useful for simulating the radiation responses of uranium dioxide and mixed oxide fuel (MOX). Controlled additions of lanthanum can also be used to form various levels of lattice oxide or anion vacancies. In previous transmission electron microscopy (TEM) experimental studies, the growth rate of dislocation loops in irradiated lanthanum doped ceria was reported to vary with lanthanum concentration. This work reports findings of the evolution mechanisms of the dislocation loops in cerium oxide with and without lanthanum dopants based on a combination of molecular statics and molecular dynamics simulations. These dislocation loops are found to be b = 1 / 3 interstitial type Frank loops. Calculations of the defect energy profiles of the dislocation loops with different structural configurations and radii reveal the basis for preference of nucleation as well as the driving force of growth. Frenkel pair evolution simulations and displacement cascade overlaps simulations were conducted for a variety of lanthanum doping conditions. The nucleation and growth processes of the Frank loop were found to be controlled by the mobility of cation interstitials, which is significantly influenced by the lanthanum doping concentration. Competition mechanisms coupled with the mobility of cation point defects were discovered, and can be used to explain the lanthanum effects observed in experiments.

  14. FT-IR Studies of Cerium Oxide Nanoparticles and Natural Zeolite Materials

    Directory of Open Access Journals (Sweden)

    Oana Lelia Pop

    2015-05-01

    Full Text Available An emerging topic of our days is nanoscience and nanotechnology successfully applied in the food industry. Characteristics such as size, surface area and morphology can modify the basic properties and the chemical reactivity of the nanomaterials. The breakthrough of innovative materials, processes, and phenomena at the nanoscale, as well as the progress of new experimental and theoretical techniques for research, supply novel opportunities for the expansion of original nanosystems and nanostructured materials. These study examine two types of nanoparticles, namely cerium oxide nanoparticles (CeO2 NP and natural zeolites. In view of the importance of CeO2 NP in various biological applications, the primary objective of this study is to characterise four samples of CeO2 NP in order to understand the role of the synthesis process in the final product. Nanocrystalline natural zeolites are materials with interesting properties which allows them to be used as adjuvant in many therapies. The characterisation of CeO2 NP and two types of natural zeolites using Fourier Transform Infrared (FT-IR spectroscopy is described. Therefore, this study examined two types of nanomaterials, namely cerium oxide nanoparticles and zeolites, for further applications on microorganisms and living cells.

  15. Elasticity of cerium up to 4.4 GPa by sound velocity measurements under hydrostatic pressure

    International Nuclear Information System (INIS)

    We report here the longitudinal and shear sound velocities on polycrystalline cerium under hydrostatic pressure across the iso-structural γ-α phase transition up to 4.4 GPa. Comparing with previous methods, the pressure-density relation of Ce has been calculated by integrating with the initial travel time and pressure without any fitting. The pressure correction of the Grüneisen parameter and linear expansion coefficient are taken into account during the integration process. The sound velocities, bulk modulus, shear modulus, Debye temperature, and vibrational entropy are achieved and have been compared with previous results. The bulk modulus of cerium in α phase agrees with the previous results determined by neutron and x-ray diffraction. The Debye temperature above and below the phase transition are θDγ=130.9 K and θDα=151.9 K, respectively. The difference of the Debye temperature from respective experiment is found and has been expounded. We consider that the vibrational entropy change per atom of 0.44 k B as the Kondo collapse of 17% volume change, and 0.70 k B as the total change from γ phase to complete α phase. (papers)

  16. Dielectric properties and electronic transitions of porous and nanostructured cerium oxide films

    International Nuclear Information System (INIS)

    Cerium dioxide (CeO2) exhibits exceptional electronic properties such as optical transparency and high refractive index (n) and high dc dielectric constant (k). Therefore, it is an attractive material for ultra-thin gate oxide in CMOS technology, where high-k dielectrics are required. We study the electronic properties of nanostructured and porous cerium oxide (CeOx) films, 110-500 nm thick, grown on Si by electron beam evaporation (EBE) and ion beam assisted deposition (IBAD). The film microstructure and morphology (grain size, porosity, defect concentration, surface and interface roughness) are controlled by varying the process parameters appropriately. They have been studied by high-resolution and transmission electron microscopy (HRTEM). The optical properties have been studied by spectroscopic ellipsometry (SE) and k was determined by capacitance measurements. We have found that the values of k and n (1.6-2.5 depending on porosity) are affected by the electronic transitions, which are strongly correlated with the microstructure and morphology of the films. We investigate how the microstructure and morphology variations affect the absolute values of the dc dielectric constant and of the dielectric function at the UV-Vis and IR spectral regions. In addition, we investigate the very important role of the defects, which have the form of grain boundaries, trivalent Ce3+ and O vacancies. As a result we were able to tailor n and k of CeOx films controlling their porosity and defect density

  17. Cerium relieving the inhibition of photosynthesis and growth of spinach caused by lead

    Institute of Scientific and Technical Information of China (English)

    ZHOU Min; ZE Yuguan; LI Na; DUAN Yanmei; CHEN Ting; LIU Chao; HONG Fashui

    2009-01-01

    Chloroplasts were isolated from spinach cultured in lead chloride-present, Ce~(3+)-administered, cerium chloride-administered lead chloride-present Hoagland's media or that of Hoagland's media. The experimental study demonstrated the effects of cerium (Ce) on distribu-tion of light energy and photochemical activities of spinach chloroplast grown in lead (Pb)-present media. It was observed that Pb~(2+) signifi-cantly inhibited photosynthesis in spinach, including light absorption, energy transfer from LHCII to photosystem II, excitation energy dis-tribution from photosystem I to photosystem II, and transformation from light energy to electron energy and oxygen evolution of chloroplasts,and decreased spinach growth. However, Ce~(3+) treatment to pb~(2+)-present chloroplasts could obviously improve light absorption and excitation energy distribution in both photosystems and increase activity of photochemical reaction and oxygen evolution of chloroplasts. The results suggested that Ce~(3+) under Pb~(2+) stress could maintain the stability of chloroplast membrane, and improve photosynthesis of spinach chloro-plast, thus promote spinach growth.

  18. Cerium relieving the inhibition of photosynthesis and growth of spinach caused by lead

    Institute of Scientific and Technical Information of China (English)

    ZHOU; Min

    2009-01-01

    Chloroplasts were isolated from spinach cultured in lead chloride-present, Ce3+-administered, cerium chloride-administered lead chloride-present Hoagland's media or that of Hoagland's media. The experimental study demonstrated the effects of cerium (Ce) on distribu-tion of light energy and photochemical activities of spinach chloroplast grown in lead (Pb)-present media. It was observed that Pb2+ signifi-cantly inhibited photosynthesis in spinach, including light absorption, energy transfer from LHCII to photosystem II, excitation energy dis-tribution from photosystem I to photosystem II, and transformation from light energy to electron energy and oxygen evolution of chloroplasts,and decreased spinach growth. However, Ce3+ treatment to pb2+-present chloroplasts could obviously improve light absorption and excitation energy distribution in both photosystems and increase activity of photochemical reaction and oxygen evolution of chloroplasts. The results suggested that Ce3+ under Pb2+ stress could maintain the stability of chloroplast membrane, and improve photosynthesis of spinach chloro-plast, thus promote spinach growth.

  19. Complete Oxidation of Methane over Palladium Supported on Alumina Modified with Calcium, Lanthanum, and Cerium Ions

    Institute of Scientific and Technical Information of China (English)

    Beata Stasinska; Wojciech Gac; Theophilos Ioannides; Andrzej Machocki

    2007-01-01

    The activity and thermal stability of Pd/Al2O3 and Pd/(Al2O3+MOx) (M=Ca, La, Ce) palladium catalysts in the reaction of complete oxidation of methane are presented in this study. The catalyst supports were prepared by sol-gel method and they were dried either conventionally or with supercritical carbon dioxide. Then they were impregnated with palladium nitrate solution. The catalysts with unmodified alumina had a high surface area. The activity and thermal stability of the alumina-supported catalyst was also very high. The introduction of calcium, lanthanum, or cerium oxide into alumina support caused a decrease of the surface area in the way dependent on the support precursor drying method. These modifiers decreased the activity of palladium catalysts, and they required higher temperatures for the complete oxidation of methane than unmodified Pd/Al2O3. The improvement of the palladium activity by lanthanum and cerium support modifier was observed only at low temperatures of the reaction.

  20. Growth of monodisperse nanocrystals of cerium oxide during synthesis and annealing

    Energy Technology Data Exchange (ETDEWEB)

    Ghosh, Swapankumar, E-mail: swapankumar.ghosh2@mail.dcu.ie; Divya, Damodaran [National Institute for Interdisciplinary Science and Technology (NIIST), Council of Scientific and Industrial Research (CSIR) (India); Remani, Kottayilpadi C. [Sree Neelakanda Government Sanskrit College, Department of Chemistry (India); Sreeremya, Thadathil S. [National Institute for Interdisciplinary Science and Technology (NIIST), Council of Scientific and Industrial Research (CSIR) (India)

    2010-06-15

    Monodisperse cerium oxide nanocrystals have been successfully synthesised using simple ammonia precipitation technique from cerium(III) nitrate solution at different temperatures in the range 35-80 {sup o}C. The activation energy for growth of CeO{sub 2} nanocrystals during the precipitation is calculated as 11.54 kJ/mol using Arrhenius plot. Average crystal diameter was obtained from XRD analysis, HR-TEM and light scattering (PCS). The analysis of size data from HR-TEM images and PCS clearly indicated the formation of highly crystalline CeO{sub 2} particles in narrow size range. CeO{sub 2} nanocrystals precipitated at 35 {sup o}C were further annealed at temperatures in the range 300-700 {sup o}C. The activation energy for crystal growth during annealing is also calculated and is close to the reported values. An effort is made to predict the mechanism of crystal growth during the precipitation and annealing.

  1. Lanthanum, cerium, praseodymium, and neodymium metals and their interaction with oxygen studied by photoelectron spectroscopy

    International Nuclear Information System (INIS)

    Clean films of La, Ce, Pr, and Nd, prepared by in situ evaporation have been investigated by photoelectron spectroscopy. Different light sources He I (hv = 21.2 eV), He II (hv = 40.8 eV) and Mg Kα (hv = 1253.6 eV) have been used for the electron excitation in order to characterize the metals. Measurements have been performed after exposing the clean metals to various amounts of oxygen. From the vanishing of the emission from the sd conduction band upon exposure the conclusion is drawn that an oxide layer thicker than the probing depth (20 A) is formed on all four metals and that the oxide (at room temperature) has the form: Me2O3, Me=La, Ce, Pr, Nd. The tetravalent cerium oxide is obtained when the film is heated to about 6000C during oxygen exposure. The interaction with oxygen is also characterized by recording the oxygen 1s level and some metal core levels (Me 3d, 4d and 4p). The results from the pure metals and from the metal oxides give further experimental evidence for a 4f level binding energy of 1.9 eV in γ-cerium. (Auth.)

  2. Visible Light Induced Photocatalysis of Cerium Ion Modified Titania Sol and Nanocrystallites

    Institute of Scientific and Technical Information of China (English)

    Yibing XIE; Chunwei YUAN

    2004-01-01

    The cerium ion(Ce4+) doped titania sol and nanocrystallites were prepared by chemical coprecipitation-peptization and hydrothermal synthesis methods, respectively. The X-ray diffraction pattern shows that Ce4+-TiO2 xerogel powder has semicrystalline structure and thermal sintering sample has crystalline structure. Ce4+-TiO2 nanocrystallites are composed of the major anatase phase titania (88.82 wt pct) and a small amount of crystalline cerium titanate.AFM micrograph shows that primary particle size of well-dispersed ultrafine sol particles is below 15 nm in diameter.The particle sizes are 30 nm for xerogel sample and 70 nm for nanocrystallites sample, which is different from the estimated values (2.41 nm and 4.53 nm) by XRD Scherrer's formula. The difference is mainly due to aggregation of nanocrystallites. The experimental results exhibit that photocatalysts of Ce4+-TiO2 sol and nanocrystallites have the ability to photodegrade reactive brilliant red dye (X-3B) under visible light irradiation with the ion-TiO2/VIS/dye system. Moreover, Ce4+ doped titania sol has shown higher efficiency than the nanocrystallites sample in respect of potocatalytic activity. Meanwhile, dye photodegradation mechanisms are proposed to different photocatalytic reaction systems, which are dye photosensitization, ion-dye photosensitization and interband photocatalysis & dye photosensitization with respect to TiO2 nanocrystallites, Ce4+-TiO2 sol and Ce4+-TiO2 nanocrystallites system.

  3. Effects of different valences of cerium ion on conformation of Horseradish Peroxidase

    Institute of Scientific and Technical Information of China (English)

    XIANG Li; GE Zhiqiang

    2008-01-01

    Our previous studies demonstrated that Ce4+ could induce reactive oxygen species (ROS) burst as a signal to promote pacilitaxel biosynthesis in suspension cultured Taxus cuspidate cells. To further understand the mechanism of cerium ions inducing ROS burst, circular dichroism (CD), synchronous fluorescence, and electron paramagnetic resonance (EPR) were used to detect them inducing conforma-tional change of horseradish peroxidase (HRF). Horseradish peroxidase activity was reduced by 78% by 0.1 mmol/L Ce4+, whereas it was only reduced by 28% by 0.1 mmol/L Ce3+. Circular dichroism spectra showed that the percentage of transition from helical content and other structure to βstrands andβturns was 23.1 when induced by Ce4+, whereas it was only 13.2 when induced by Ce3+. In synchronous fluorescence spectra, Ce4+ led to red shift and intensity-elevation of tryptophan fluorescence emission maximum, whereas in the case of Ce3+, the results were a contrast to the above. Furthermore, g factor (gx and gy) in electron paramagnetic resonance (EPR) induced by Ce4+ and Ce3+ was significantly different. These results indicated that the different valence of cerium ion induced various conformations of HRP, and Ce4+ was more effective than Ce3+. This suggested that Ce4+ affected the burst of ROS through changing the conformation of oxidoreductase.

  4. Cerium-zinc redox flow battery: Positive half-cell electrolyte studies

    Institute of Scientific and Technical Information of China (English)

    XIE Zhipeng; ZHOU Debi; XIONG Fengjiao; ZHANG Shimin; HUANG Kelong

    2011-01-01

    Experimental work was performed to evaluate the Ce3+/Ce4+ redox couple in methane sulfonic acid (MSA) electrolyte for use in redox flow battery (RFB) technology. The electrochemical behaviour of the Ce3+/Ce4+ in MSA media was investigated using cyclic voltammetry, linear sweep voltammetry, chronoamperometry and rotating disc electrode. The standard rate constant of the Ce3+/Ce4+ redox reaction on graphite electrode in MSA was 4.06x10-4 cm/s. The diffusion coefficient of Ce3+ in MSA was 5.87-6.15x10-6 cm2/s, and was 2.56-2.68x 10-6 cm2/s for Ce4+. The energy efficiency of a cerium-zinc test cell was 74.8%. The high stability of cerium salts in MSA media and relatively fast redox kinetics of the Ce3+/Ce4+ redox reaction at graphite ectrode indicated that the Ce3+/Ce4+ might be well suited for use in RFB technology.

  5. Direct liquid injection chemical vapor deposition of platinum doped cerium oxide thin films

    International Nuclear Information System (INIS)

    Thin films of Pt-doped CeO2 were grown by direct liquid injection chemical vapor deposition on silicon wafer covered by native oxide at 400 °C using Ce(IV) alkoxide and organoplatinum(IV) as precursors. X-ray photoelectron spectra evidenced that the platinum oxidation state is linked to the deposition way. For platinum deposited on top of cerium oxide thin films previously grown, metallic platinum particles were obtained. Cerium and platinum codeposition allowed obtaining a Pt0 and Pt2+ mixture with the Pt2+ to Pt ratio strongly dependent on the platinum flow rate during the deposition. Indeed, the lower the platinum precursor flow rate is, the higher the Pt2+ to Pt ratio is. Moreover, surface and cross-sectional morphologies obtained by scanning electron microscopy evidenced porous layers in any case. - Highlights: • Pt-doped ceria were synthesized. • Films were obtained by direct liquid injection chemical vapor deposition. • Simultaneous deposition of Pt and Ce was used to obtain homogeneous films. • Pt2+ was revealed through X-ray photoelectron spectroscopy. • Different routes were used to exalt Pt2+/Pt ratio

  6. Magnetic studies of GaN nanoceramics doped with 1% of cerium

    Institute of Scientific and Technical Information of China (English)

    K. Oganisian; P. Gluchowski; W. Strek

    2011-01-01

    The magnetization measurements of gallium intride nanoceramics doped with 1% of cerium and sintered under various pressures were reported.It was found that GaN nanoceramics doped with cerium showed paramagnetic behavior in the wide temperature range.Nanoceramics of GaN with 1% of Ce (as undoped GaN) was diamagnetic one,but under certain temperature the paramagnetic properties started to dominate.This crossover temperature was nonlinearly dependent on the pressure applied during the sintering.The fitting of molar magnetic susceptibility allowed to estimate the Curie temperature,Curie constant and diamagnetic part of susceptibility.As it was found,all the samples showed the antiferromagnetic ordering with θp≈-1 K.Also,the effective magnetic moment was estimated for all of the samples.As a result,magnetic moments in terms of Ce ion were notably larger in comparison with those obtained within the Russell-Saunders coupling model.We suggested that it was the strong influence of amorphous shell which was rising with the pressure applied during the sintering.Finally,we presented dependences of magnetization as a function of applied field.All the samples manifested weak ferromagnetism at high temperatures and paramagnetic behavior in low temperature region.

  7. [XPS study on the influence of calcination conditions to cerium ion valence].

    Science.gov (United States)

    Mei, Yan; Yan, Jian-ping; Nie, Zuo-ren

    2010-01-01

    For the system of Ce(NO3)2.6H2O and urea solution during homogeneous precipitation method, X-ray diffraction (XRD), infrared spectrum (IR) and especially X-ray photoelectron spectroscopy (XPS) were used to study and characterize the product structure, variety of cerium ion valence, compound surface character and kernel electronic configurations. The results of XRD and IR showed that calcination temperature had a great effect on the cerium ion valence. The products are orthorhombic Ce2 O(CO3)2.H2O with valence III by using homogeneous precipitation method directly. When heated from the temperature 200 degrees C to 250 degrees C, the product of CeO(CO3)2.H2O with valence VI was finally changed into stable CeO2 with valence IV. XPS was used to study the surface character and kernel electronic configurations of the three different compounds through fine scanning of O(1s), Ce(3d) and Ce(4d) apices, and the results approved that the compounds with different valences are caused by the different valence electronic configurations of the products.

  8. Cerium oxide nanoparticles stimulate proliferation of primary mouse embryonic fibroblasts in vitro.

    Science.gov (United States)

    Popov, Anton L; Popova, Nelly R; Selezneva, Irina I; Akkizov, Azamat Y; Ivanov, Vladimir K

    2016-11-01

    The increasing application of cell therapy technologies in the treatment of various diseases requires the development of new effective methods for culturing primary cells. The major limitation for the efficient use of autologous cell material is the low rate of cell proliferation. Successful cell therapy requires sufficient amounts of cell material over a short period of time with the preservation of their differentiation and proliferative potential. In this regard, the development of novel, highly efficient stimulators of proliferative activity in stem cells is a truly urgent task. In this paper we have demonstrated that citrate-stabilized cerium oxide nanoparticles (nanoceria) enhance the proliferative activity of primary mouse embryonic fibroblasts in vitro. Cerium oxide nanoparticles stimulate cell proliferation in a wide range of concentrations (10(-3)М-10(-9)M) through reduction of intracellular levels of reactive oxygen species (ROS) during the lag phase of cell growth and by modulating the expression level of the major antioxidant enzymes. We found the optimal concentration of nanoceria, which provides the greatest acceleration of cell proliferation in vitro, while maintaining the levels of intracellular ROS and mRNA of antioxidant enzymes in the physiological range. Our results confirm that nanocrystalline ceria can be considered as a basis for effective and inexpensive supplements in cell culturing. PMID:27524035

  9. Direct liquid injection chemical vapor deposition of platinum doped cerium oxide thin films

    Energy Technology Data Exchange (ETDEWEB)

    Zanfoni, N.; Avril, L.; Imhoff, L.; Domenichini, B., E-mail: bruno.domenichini@u-bourgogne.fr; Bourgeois, S.

    2015-08-31

    Thin films of Pt-doped CeO{sub 2} were grown by direct liquid injection chemical vapor deposition on silicon wafer covered by native oxide at 400 °C using Ce(IV) alkoxide and organoplatinum(IV) as precursors. X-ray photoelectron spectra evidenced that the platinum oxidation state is linked to the deposition way. For platinum deposited on top of cerium oxide thin films previously grown, metallic platinum particles were obtained. Cerium and platinum codeposition allowed obtaining a Pt{sup 0} and Pt{sup 2+} mixture with the Pt{sup 2+} to Pt ratio strongly dependent on the platinum flow rate during the deposition. Indeed, the lower the platinum precursor flow rate is, the higher the Pt{sup 2+} to Pt ratio is. Moreover, surface and cross-sectional morphologies obtained by scanning electron microscopy evidenced porous layers in any case. - Highlights: • Pt-doped ceria were synthesized. • Films were obtained by direct liquid injection chemical vapor deposition. • Simultaneous deposition of Pt and Ce was used to obtain homogeneous films. • Pt{sup 2+} was revealed through X-ray photoelectron spectroscopy. • Different routes were used to exalt Pt{sup 2+}/Pt ratio.

  10. Kinetics of Cerium(IV) Extraction from H(2)SO(4)-HF Medium with Cyanex 923.

    Science.gov (United States)

    Liao, Wuping; Yu, Guihong; Yue, Shantang; Li, Deqian

    2002-03-11

    Studies of the extraction kinetics of cerium(IV) from H(2)SO(4)-HF solutions with Cyanex 923 in n-heptane have been carried out using a constant interfacial area cell with laminar flow. The experimental hydrodynamic conditions were chosen so that the contribution of diffusion to the measured rate of reaction was minimized. The data were analyzed in terms of pseudo-first order constants. The results were compared with those of the system without HF. It was concluded that the addition of HF reduces the activation energy for the forward rate from 46.2 to 36.5 kJ mol(-1) while it has an opposite effect on the activation energy for the reverse process(the activation energy increased from 23.3 to 90.8 kJ mol(-1)). Thus, HF can accelerate the rate of cerium(IV) extraction. At the same time, the extraction rate is controlled by a mixed chemical reaction-diffusion rather than by a chemical reaction alone. A rate equation has also been obtained.

  11. Custom cerium oxide nanoparticles protect against a free radical mediated autoimmune degenerative disease in the brain.

    Science.gov (United States)

    Heckman, Karin L; DeCoteau, William; Estevez, Ana; Reed, Kenneth J; Costanzo, Wendi; Sanford, David; Leiter, James C; Clauss, Jennifer; Knapp, Kylie; Gomez, Carlos; Mullen, Patrick; Rathbun, Elle; Prime, Kelly; Marini, Jessica; Patchefsky, Jamie; Patchefsky, Arthur S; Hailstone, Richard K; Erlichman, Joseph S

    2013-12-23

    Cerium oxide nanoparticles are potent antioxidants, based on their ability to either donate or receive electrons as they alternate between the +3 and +4 valence states. The dual oxidation state of ceria has made it an ideal catalyst in industrial applications, and more recently, nanoceria's efficacy in neutralizing biologically generated free radicals has been explored in biological applications. Here, we report the in vivo characteristics of custom-synthesized cerium oxide nanoparticles (CeNPs) in an animal model of immunological and free-radical mediated oxidative injury leading to neurodegenerative disease. The CeNPs are 2.9 nm in diameter, monodispersed and have a -23.5 mV zeta potential when stabilized with citrate/EDTA. This stabilizer coating resists being 'washed' off in physiological salt solutions, and the CeNPs remain monodispersed for long durations in high ionic strength saline. The plasma half-life of the CeNPs is ∼4.0 h, far longer than previously described, stabilized ceria nanoparticles. When administered intravenously to mice, the CeNPs were well tolerated and taken up by the liver and spleen much less than previous nanoceria formulations. The CeNPs were also able to penetrate the brain, reduce reactive oxygen species levels, and alleviate clinical symptoms and motor deficits in mice with a murine model of multiple sclerosis. Thus, CeNPs may be useful in mitigating tissue damage arising from free radical accumulation in biological systems.

  12. Self-healing Performance of Composite Coatings Prepared by Phosphating and Cerium Nitrate Post-sealing

    Institute of Scientific and Technical Information of China (English)

    LIN Bilan; LU Jintang

    2015-01-01

    The phosphated and cerium nitrate post-sealed galvanized steel was ifrstly scratched to expose zinc layer and then placed in neutral salt spray (NSS) chamber for different durations. The microstructure and compositions of the scratches were investigated using SEM and EDS. The phases of the corrosion products were examined through XRD. The self-healing mechanism of the composite coatings was discussed. The experimental results show that the composite coatings have an excellent corrosion resistance. The corrosion products increase with corrosion time and ifnally cover the whole scratch. They contain phosphorous, cerium, oxygen, chloride and zinc, and are ifne needle and exceedingly compact. The composite coatings are favorable self-healing. During corrosion, the self-healing ions such as Ce3+, Ce4+, PO43-, Zn2+ in the composite coatings were dissolved, migrated, recombined, and covered the exposed zinc, impeding zinc corrosion. The self-healing process of the scratches on the composite coatings can be divided into three stages, about 2 h, 4 h, and 24 h, respectively.

  13. Corrosion behaviour of sol-gel coatings doped with cerium salts on 2024-T3 aluminum alloy

    Energy Technology Data Exchange (ETDEWEB)

    Shi Hongwei; Liu Fuchun [State Key Laboratory for Corrosion and Protection, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Han Enhou, E-mail: ehhan@imr.ac.cn [State Key Laboratory for Corrosion and Protection, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China)

    2010-11-01

    The corrosion behaviour of the sol-gel coatings doped with cerium chloride or cerium nitrate on 2024-T3 aluminum alloy was investigated by using electrochemical impedance spectroscopy (EIS) and immersion tests. The sol-gel matrix was obtained through hydrolysis, condensation of 3-glycidoxypropyltrimethoxysilane (GPTMS) and tetramethoxysilane (TMOS), using diethylentriamine as curing agent. The results indicated that cerium nitrate with concentration of 1 x 10{sup -3} mol L{sup -1} in the silane solution was excellent on self-healing for the sol-gel coating, while cerium chloride had no obvious effect. This result suggested that the introduction of Cl{sup -} promoted the under-film pitting of 2024-T3 substrate. It was found that Ce(OH){sub 3} and Ce(OH){sub 2}{sup 2+} simultaneously existed in the silane solution by X-ray diffraction (XRD) analysis. Ce(OH){sub 2}{sup 2+} transformed to CeO{sub 2} due to high-temperature curing of sol-gel matrix demonstrated by X-ray photoelectron spectroscopy (XPS) analysis. Therefore, it can be considered that Ce(OH){sub 3} and CeO{sub 2} played inhibition roles in the corrosion process of the sol-gel coatings.

  14. Effect of cerium ion implantation on the oxidation behavior of zircaloy-4 at 500 degree sign C

    CERN Document Server

    Chen, X W; Yu, H R; Zhou, Q G; Chen, B S

    2002-01-01

    In order to investigate the oxidation behavior changes of zircaloy-4 induced by cerium ion implantation using a MEVVA source at an energy of 40 keV with a dose range from 1x10 sup 1 sup 6 to 1x10 sup 1 sup 7 ions/cm sup 2 at the maximum temperature of 130 degree sign C, weight gain curves of the different specimens including as-received zircaloy-4 and cerium-implanted zircaloy-4 were measured after oxidation in air at 500 degree sign C for 100 min. It was obviously found that a significant improvement was achieved in the oxidation behavior of cerium ion implanted zircaloy-4 compared with that of the as-received zircaloy-4. The depth profile of the element composition in the surface region of the samples was obtained by Auger electron spectroscopy, and the valence of the oxides in the scale was analyzed by X-ray photoemission spectroscopy. Glancing angle X-ray diffraction employed to examine the phase transformation in the oxide films showed that the addition of cerium transformed the phase from monoclinic zir...

  15. Influence of hydroxyl content of binders on rheological properties of cerium-gadolinium oxide (CGO) screen printing inks

    DEFF Research Database (Denmark)

    Marani, Debora; Gadea, Christophe; Hjelm, Johan;

    2015-01-01

    vinyl resins) were selected and characterized in solution via viscosimetry method. A high degree of hyper-entanglement was observed for ethyl cellulose polymers, whereas a mitigated effect characterized the two vinyl resins. Cerium-gadolinium oxides (CGO)-based inks, prepared using the selected binders...

  16. Research Development of Cerium-Zinc Flow Battery%铈锌液流电池的研究进展

    Institute of Scientific and Technical Information of China (English)

    金荣荣; 马立群; 尹东明; 王立民

    2013-01-01

    Cerium-Zinc redox flow battery has a significant high voltage compared with other redox flow batteries.The potential utilization of cerium-zinc redox flow battery is most likely to occur in energy storage system due to the abundant resources of raw materials and cost-efficient products.This review summarized the recent research and development of cerium-zinc flow batteries,especially for electrolytes of batteries,and analyzes further development prospective of cerium-zinc flow batteries.%铈锌氧化还原液流电池与其它液流电池相比,具有电压高、原材料资源丰富和价格便宜等优点,在储能方面具有很大的应用发展潜力.本文总结了铈锌液流电池的研究进展,特别是对电解液的发展进行了重点总结,并指出了今后铈锌液流电池研究的发展方向.

  17. Germination and early plant development of ten plant species exposed to titanium dioxide and cerium oxide nanoparticles

    Science.gov (United States)

    Ten agronomic plant species were exposed to different concentrations of nano titanium dioxide (nTiO2) or nano cerium oxide (nCeO2) (0, 250, 500 and 1000 mg/L) to examine potential effects on germination and early seedling development. We modified a standard test protocol develop...

  18. A mixed acid based vanadium-cerium redox flow battery with a zero-gap serpentine architecture

    Science.gov (United States)

    Leung, P. K.; Mohamed, M. R.; Shah, A. A.; Xu, Q.; Conde-Duran, M. B.

    2015-01-01

    This paper presents the performance of a vanadium-cerium redox flow battery using conventional and zero-gap serpentine architectures. Mixed-acid solutions based on methanesulfonate-sulfate anions (molar ratio 3:1) are used to enhance the solubilities of the vanadium (>2.0 mol dm-3) and cerium species (>0.8 mol dm-3), thus achieving an energy density (c.a. 28 Wh dm-3) comparable to that of conventional all-vanadium redox flow batteries (20-30 Wh dm-3). Electrochemical studies, including cyclic voltammetry and galvanostatic cycling, show that both vanadium and cerium active species are suitable for energy storage applications in these electrolytes. To take advantage of the high open-circuit voltage (1.78 V), improved mass transport and reduced internal resistance are facilitated by the use of zero-gap flow field architecture, which yields a power density output of the battery of up to 370 mW cm-2 at a state-of-charge of 50%. In a charge-discharge cycle at 200 mA cm-2, the vanadium-cerium redox flow battery with the zero-gap architecture is observed to discharge at a cell voltage of c.a. 1.35 V with a coulombic efficiency of up to 78%.

  19. Effect of rare element cerium on the morphology and corrosion resistance of electro-less Ni-P coatings

    Directory of Open Access Journals (Sweden)

    Fu Chuan-qi

    2015-01-01

    Full Text Available This paper reports an experimental study on the microstructure and corrosion resistance of electro-less Ni-P coatings with increasing content of the rare element cerium (Ce. Surface morphology and the composition of the electro-less Ni-P coatings were studied by scanning electron microscope (SEM, X-ray energy dispersed analysis (EDS and X-ray diffraction analysis (XRD. Hardness and Adhesive force are researched by a HX-200 Vickers diamond indenter micro-hardness tester. Furthermore, we study the adhesive force by using the Revetest scratch tester. We get the possession of Ce amorphous Ni-P coatings which has excellent properties in anti-corrosion. The effect of the rare element cerium concentration on corrosion resistance of the coatings was evaluated in the groundwater immersion test and porosity test, respectively. The results indicated that added little the rare element cerium into the plating bath increased the phosphorus content of the coatings, decreased the corrosion rates, it also decreases the porosity of the amorphous Ni-P coatings. The lowest corrosion rates of the amorphous Ni-P coatings in groundwater immersion test is 4.1 um · h-1, at the rare element cerium concentration of 0.12g · L-1.

  20. Interaction of the 106-126 prion peptide with lipid membranes and potential implication for neurotoxicity

    International Nuclear Information System (INIS)

    Prion diseases are fatal neurodegenerative disorders characterized by the accumulation in the brain of an abnormally misfolded, protease-resistant, and β-sheet rich pathogenic isoform (PrPsc) of the cellular prion protein (PrPc). In the present work, we were interested to study the mode of prion protein interaction with the membrane using the 106-126 peptide and small unilamellar lipid vesicles as model. As previously demonstrated, we showed by MTS assay that PrP 106-126 induces alterations in the human neuroblastoma SH-SY5Y cell line. We demonstrated for the first time by lipid-mixing assay and by the liposome vesicle leakage test that PrP 106-126, a non-tilted peptide, induces liposome fusion thus a potential cell membrane destabilization, as supported by membrane integrity assay (LDH). By circular dichroism (CD) analysis we showed that the fusogenic property of PrP 106-126 in the presence of liposome is associated with a predominantly β-sheet structure. These data suggest that the fusogenic property associated with a predominant β-sheet structure exhibited by the prion peptides contributes to the neurotoxicity of these peptides by destabilizing cellular membranes. The latter might be attached at the membrane surface in a parallel orientation as shown by molecular modeling

  1. Cleanup Verification Package for the 126-F-1, 184-F Powerhouse Ash Pit

    Energy Technology Data Exchange (ETDEWEB)

    S. W. Clark and H. M Sulloway

    2007-10-31

    This cleanup verification package documents completion of remedial action for the 126-F-1, 184-F Powerhouse Ash Pit. This waste site received coal ash from the 100-F Area coal-fired steam plant. Leakage of process effluent from the 116-F-14 , 107-F Retention Basins flowed south into the ash pit, contaminating the northern portion.

  2. 45 CFR 96.126 - Capacity of treatment for intravenous substance abusers.

    Science.gov (United States)

    2010-10-01

    ... ADMINISTRATION BLOCK GRANTS Substance Abuse Prevention and Treatment Block Grant § 96.126 Capacity of treatment... programs that receive funding under the grant and that treat individuals for intravenous substance abuse to... 45 Public Welfare 1 2010-10-01 2010-10-01 false Capacity of treatment for intravenous...

  3. Performance Test of gPhone (#123, #126, and #127) in Kyoto and ITB Jatinangor

    Science.gov (United States)

    Wahyudi, E. J.; Fukuda, Y.; Nishijima, J.; Itakura, M.

    2016-08-01

    Gravity team of ITB, Kyoto University, and Kyushu University plan to carry out super hybrid measurement to monitor Carbon Capture Storage (CCS) injection in Gundih. During preparation stage and baseline survey before injection phase, gravity team analyze gPhone performance. Performance test of gPhone gravimeters in 2014 conducted in Kyoto and Jatinangor (three gPhone (#123, #126, and #127) placed in the same location). The tidal analysis program BAYTAP-G was used to decompose the gravity data into four components (tidal, trend, irregular, and response for auxiliary data). Response component in Kyoto relatively has lower frequency compare to Jatinangor, due to differences of the two measurement location. Response component from the longest time recording data (gPhone #123) give similiar pattern as gPhone #126, while gPhone #127 slightly different. Average standard deviation of the response component of three gPhone (#123, #126, and #127) respectively were 0.8, 1.0, and 1.9 μGal. Best drift achieved from this test show possibility to reach -4 to 5 pGal/day. Although gPhone #126 records different trend, but from tidal analysis comparison shows similiarity with gPhone #123.

  4. 13 CFR 126.204 - May a qualified HUBZone SBC have affiliates?

    Science.gov (United States)

    2010-01-01

    ... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false May a qualified HUBZone SBC have... PROGRAM Requirements to be a Qualified HUBZone SBC § 126.204 May a qualified HUBZone SBC have affiliates? A concern may have affiliates provided that the aggregate size of the concern and all of...

  5. Cleanup Verification Package for the 126-F-1, 184-F Powerhouse Ash Pit

    Energy Technology Data Exchange (ETDEWEB)

    S. W. Clark and H. M. Sulloway

    2007-09-26

    This cleanup verification package documents completion of remedial action for the 126-F-1, 184-F Powerhouse Ash Pit. This waste site received coal ash from the 100-F Area coal-fired steam plant. Leakage of process effluent from the 116-F-14 , 107-F Retention Basins flowed south into the ash pit, contaminating the northern portion.

  6. Crystal structure and conformational flexibility of the unligated FK506-binding protein FKBP12.6

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Hui; Mustafi, Sourajit M. [New York State Department of Health, Empire State Plaza, Albany, NY 12201 (United States); LeMaster, David M. [New York State Department of Health, Empire State Plaza, Albany, NY 12201 (United States); University at Albany – SUNY, Empire State Plaza, Albany, NY 12201 (United States); Li, Zhong [New York State Department of Health, Empire State Plaza, Albany, NY 12201 (United States); Héroux, Annie [Brookhaven National Laboratory, Upton, NY 11973 (United States); Li, Hongmin; Hernández, Griselda, E-mail: griselda@wadsworth.org [New York State Department of Health, Empire State Plaza, Albany, NY 12201 (United States); University at Albany – SUNY, Empire State Plaza, Albany, NY 12201 (United States)

    2014-03-01

    Two crystal forms of unligated FKBP12.6 exhibit multiple conformations in the active site and in the 80s loop, the primary site for known protein-recognition interactions. The previously unreported NMR backbone assignment of FKBP12.6 revealed extensive doubling of amide resonances, which reflects a slow conformational transition centered in the 80s loop. The primary known physiological function of FKBP12.6 involves its role in regulating the RyR2 isoform of ryanodine receptor Ca{sup 2+} channels in cardiac muscle, pancreatic β islets and the central nervous system. With only a single previously reported X-ray structure of FKBP12.6, bound to the immunosuppressant rapamycin, structural inferences for this protein have been drawn from the more extensive studies of the homologous FKBP12. X-ray structures at 1.70 and 1.90 Å resolution from P2{sub 1} and P3{sub 1}21 crystal forms are reported for an unligated cysteine-free variant of FKBP12.6 which exhibit a notable diversity of conformations. In one monomer from the P3{sub 1}21 crystal form, the aromatic ring of Phe59 at the base of the active site is rotated perpendicular to its typical orientation, generating a steric conflict for the immunosuppressant-binding mode. The peptide unit linking Gly89 and Val90 at the tip of the protein-recognition ‘80s loop’ is flipped in the P2{sub 1} crystal form. Unlike the >30 reported FKBP12 structures, the backbone conformation of this loop closely follows that of the first FKBP domain of FKBP51. The NMR resonances for 21 backbone amides of FKBP12.6 are doubled, corresponding to a slow conformational transition centered near the tip of the 80s loop, as recently reported for 31 amides of FKBP12. The comparative absence of doubling for residues along the opposite face of the active-site pocket in FKBP12.6 may in part reflect attenuated structural coupling owing to increased conformational plasticity around the Phe59 ring.

  7. Crystal structure and conformational flexibility of the unligated FK506-binding protein FKBP12.6

    International Nuclear Information System (INIS)

    Two crystal forms of unligated FKBP12.6 exhibit multiple conformations in the active site and in the 80s loop, the primary site for known protein-recognition interactions. The previously unreported NMR backbone assignment of FKBP12.6 revealed extensive doubling of amide resonances, which reflects a slow conformational transition centered in the 80s loop. The primary known physiological function of FKBP12.6 involves its role in regulating the RyR2 isoform of ryanodine receptor Ca2+ channels in cardiac muscle, pancreatic β islets and the central nervous system. With only a single previously reported X-ray structure of FKBP12.6, bound to the immunosuppressant rapamycin, structural inferences for this protein have been drawn from the more extensive studies of the homologous FKBP12. X-ray structures at 1.70 and 1.90 Å resolution from P21 and P3121 crystal forms are reported for an unligated cysteine-free variant of FKBP12.6 which exhibit a notable diversity of conformations. In one monomer from the P3121 crystal form, the aromatic ring of Phe59 at the base of the active site is rotated perpendicular to its typical orientation, generating a steric conflict for the immunosuppressant-binding mode. The peptide unit linking Gly89 and Val90 at the tip of the protein-recognition ‘80s loop’ is flipped in the P21 crystal form. Unlike the >30 reported FKBP12 structures, the backbone conformation of this loop closely follows that of the first FKBP domain of FKBP51. The NMR resonances for 21 backbone amides of FKBP12.6 are doubled, corresponding to a slow conformational transition centered near the tip of the 80s loop, as recently reported for 31 amides of FKBP12. The comparative absence of doubling for residues along the opposite face of the active-site pocket in FKBP12.6 may in part reflect attenuated structural coupling owing to increased conformational plasticity around the Phe59 ring

  8. Methylation of the miR-126 gene associated with glioma progression.

    Science.gov (United States)

    Cui, Hongwei; Mu, Yongping; Yu, Lei; Xi, Ya-guang; Matthiesen, Rune; Su, Xiulan; Sun, Wenjie

    2016-04-01

    Gliomas are the most common and the most malignant brain tumors, accouting for 45-55% of all intracranial tumors. The incidence of glioma worldwide is about 6-12 per 100,000. Recently, several studies showed that the activation of the oncogenes and the inactivation and/or loss of the tumor suppressor genes, especially for miRNA-21, let-7 and so on, are the most primary molecule event in gliomas. MicroRNAs (miRNAs) are a class of endogenously expressed small noncoding RNAs which are usually 21-23 nucleotides long. miRNAs regulate gene expression and play important roles in a variety of physiological and pathological processes, such as cell proliferation, differentiation and apoptosis. To date, Growing evidence has shown that mi RNAs are frequently dysregulated in human cancers and can act as both tumor suppressors and oncogenes. Along with the discovery of micro RNA, more and more research focusing on its relationship with glioma was carried out to investigate the biological features of glioma and to provide experimental evidence for glioma mechanism. In the present study, we aimed to verify the miRNA-126 down-regulation which showed in the results of glioma tissue miRNAs chip and discuss the miRNA-126 methylation in patients with glioma. A total of 50 samples from patients with glioma and 20 control samples from patients with cerebral trauma were included in this study. The expression levels of the miR-126 gene were detected using quantitative polymerase chain reaction (PCR), and the methylation status of miR-126 was examined using methylation-specific PCR-denaturing high-performance liquid chromatography (MSP-DHPLC). The expression level of miRNA-126 was found to be significantly higher in the control group (0.6134 ± 0.1214) than in the glioma group (0.2771 ± 0.1529; P < 0.05). The expression was also significantly elevated in low-grade gliomas (0.3117 ± 0.1474) compared with high-grade gliomas (0.1582 ± 0.1345; P < 0.05). In addition, increased methylation of

  9. Computational and Experimental Study of the Thermodynamics of Uranium-Cerium Mixed Oxides

    Science.gov (United States)

    Hanken, Benjamin Edward

    The thermophysical properties of mixed oxide (MOX) fuels, and how they are influenced by the incorporation of fission products and other actinides, must be well understood for their safe use in an advanced fuel cycle. Cerium is a common plutonium surrogate in experimental studies of MOX, as it closely matches plutonium's ionic radii in the 3+ and 4+ oxidation states, and is soluble in fluorite-structured UO2. As a fission product, cerium's effects on properties of MOX are also of practical interest. To provide additional insights on structure-dependent behavior, urania solid solutions can be studied via density functional theory (DFT), although approaches beyond standard DFT are needed to properly account for the localized nature of the ƒ-electrons. In this work, DFT with Hubbard-U corrections (DFT+U) was employed to study the energetics of fluorite-structured U1-yCe yO2 mixtures. The employed computational approach makes use of a procedure which facilitates convergence of the calculations to multiple self-consistent DFT+U solutions for a given cation arrangement, corresponding to different charge states for the U and Ce ions in several prototypical cation arrangements. Results indicate a significant dependence of the structural and energetic properties of U1-yCeyO2 on the nature of both charge and cation ordering. With the effective Hubbard-U parameters that reproduce well the measured oxidation-reduction energies for urania and ceria, it was found that charge transfer between U4+ and Ce4+ ions, leading to the formation of U5+ and Ce3+, gives rise to an increase in the mixing energy in the range of 4-14 kJ/mol of the formula unit, depending on the nature of the cation ordering. In conjunction with the computational approach, high-temperature oxide-melt drop-solution calorimetry experiments were performed on eight samples spanning compositions of y = 0.119 to y = 0.815. Room temperature mixing enthalpies of U1-yCeyO2 determined from these experiments show near

  10. Cerium doped lanthanum halides: fast scintillators for medical imaging; Halogenures de lanthane dopes cerium des scintillateurs rapides pour l'imagerie medicale

    Energy Technology Data Exchange (ETDEWEB)

    Selles, O

    2006-12-15

    This work is dedicated to two recently discovered scintillating crystals: cerium doped lanthanum halides (LaCl{sub 3}:Ce{sup 3+} and LaBr{sub 3}:Ce{sup 3+}).These scintillators exhibit interesting properties for gamma detection, more particularly in the field of medical imaging: a short decay time, a high light yield and an excellent energy resolution. The strong hygroscopicity of these materials requires adapting the usual experimental methods for determining physico-chemical properties. Once determined, these can be used for the development of the industrial manufacturing process of the crystals. A proper comprehension of the scintillation mechanism and of the effect of defects within the material lead to new possible ways for optimizing the scintillator performance. Therefore, different techniques are used (EPR, radioluminescence, laser excitation, thermally stimulated luminescence). Alongside Ce{sup 3+} ions, self-trapped excitons are involved in the scintillation mechanism. Their nature and their role are detailed. The knowledge of the different processes involved in the scintillation mechanism leads to the prediction of the effect of temperature and doping level on the performance of the scintillator. A mechanism is proposed to explain the thermally stimulated luminescence processes that cause slow components in the light emission and a loss of light yield. Eventually the study of afterglow reveals a charge transfer to deep traps involved in the high temperature thermally stimulated luminescence. (author)

  11. P126

    Directory of Open Access Journals (Sweden)

    A. Makashov

    2015-11-01

    Conclusion: 1. The evolution of human oncogenome advances ahead of all other human gene classes. 2. On the other hand, the evolution of tumor antigen gene classes goes behind the rest of human gene classes, i.e. tumor antigens genome is more evolutionary novel.

  12. Effect of Rare Earth Element Cerium on Mechanical Properties and Morphology of TiN Coating Prepared by Arc Ion Plating

    Institute of Scientific and Technical Information of China (English)

    黄拿灿; 胡社军; 谢光荣; 曾鹏; 汝强

    2003-01-01

    TiN coatings were deposited on polished substrates of W18Cr4V high speed steel by means of vacuum arc ion plating. The effect of cerium on adhesion between TiN coating and substrate was studied. The microstructures and composition of TiN coatings were also investigated by means of scanning electron microscope (SEM), Auger electron spectroscopy (AES), and X-ray diffraction (XRD) technique. It was found that cerium is an effective modifying agent and the addition of suitable amount of cerium to TiN coatings can produce relatively excellent properties such as micro-hardness, wear resistance, oxidation resistance and porosity. The experimental results show that the added cerium in TiN coatings makes a contribution to form the preferred direction along with a (111) or (222) close packed face, which may be one of the reasons that improves some properties mentioned above.

  13. Effects of acetic acid on microstructure and electrochemical properties of nano cerium oxide films coated on AA7020-T6 aluminum alloy

    Institute of Scientific and Technical Information of China (English)

    H. Hasannejad; T. Shahrabi; M. Aliofkhazraei

    2009-01-01

    Nano cerium oxide films were applied on AA7020-T6 aluminum alloy and the effects of acetic acid concentration on the microstructure and electrochemical properties of the coated samples were investigated by using scanning electron microscopy (SEM), X-ray diffraction (XRD), crack-flee films with well-developed grains were obtained and grain sizes of the films decreased. Elimination of cracks and decreasing grain size of the nano cerium oxide films caused corrosion resistance to increase.

  14. Effect of cerium and lanthanum additives on plasma electrolytic oxidation of AZ31 magnesium alloy

    Institute of Scientific and Technical Information of China (English)

    沈德久; 马豪杰; 郭长虹; 蔡景瑞; 李国龙; 何东磊; 杨庆祥

    2013-01-01

    Plasma electrolytic oxidation (PEO) coatings on AZ31 magnesium (Mg) alloy were developed using the aqueous solution with alkaline silicate and sodium hydroxide as a base electrolyte system. The effects of cerium (Ce) nitrate and lanthanum (La) nitrate additives on the voltage response, microstructure, compositions and corrosion resistance of PEO coatings were investigated by scan-ning electron microscopy (SEM), energy-dispersive spectrum (EDS), X-ray diffraction (XRD) and potentiodynamic polarization tests, etc. The results showed that Ce and La additives increased the stable voltage and compactness of the PEO coatings, while, those did not change the compositions of the PEO coatings. The corrosion resistance of the PEO coating obtained in solutions with La nitrate of 0.1 g/L was the best, followed by that with Ce nitrate of 0.1 g/L and that without additives.

  15. Aqueous systems of ethanolamine hydrochlorides and of chlorides of cerium, terbium, dysprosium, erbium

    International Nuclear Information System (INIS)

    The isothermal method of cross sections has been used to study the solubility at 25 and 50 deg C in ternary water-salt systems consisting of cerium chloride and mono-(1), di-(2) and triethanolamine (3) hydrochlorides as well as diethanolamine hydrochloride and terbium, dysprosium and erbium chlorides. Solubility isotherms testify to the formation in the system (1) of a congruently dissolved compound of the CeCl3x2(C2H4OHNN2HCl)x2H2O composition. Individual peculiarities of a new solid phase are proved by the DTA method by means of derivatograph ODL-106, while the composition is confirmed by chemical analysis. The rest of the systems - are of simple eutonic type

  16. Boric Acid as an Accelerator of Cerium Surface Treatment on Aluminum

    Directory of Open Access Journals (Sweden)

    K. Cruz-Hernández

    2014-01-01

    Full Text Available Aluminum pieces are often used in various industrial processes like automotive and aerospace manufacturing, as well as in ornamental applications, so it is necessary to develop processes to protect these materials, processes that can be industrialized to protect the aluminum as well or better than chromate treatments. The purpose of this research is to evaluate boric acid as an accelerator by optimizing its concentration in cerium conversion coatings (CeCC with 10-minute immersion time with a concentration of 0.1 g L−1 over aluminum to protect it. The evaluation will be carried out by measuring anticorrosion properties with electrochemical techniques (polarization resistance, Rp, polarization curves, PC, and electrochemical impedance spectroscopy, EIS in NaCl 3.5% wt. aqueous solution and surface characterization with scanning electron microscopy (SEM.

  17. Effect of cerium on ignition point of AZ91D magnesium alloy

    Directory of Open Access Journals (Sweden)

    Zhao Hongjin

    2008-02-01

    Full Text Available The surface and interior temperature-time curves of blocky cerium modified AZ91D magnesium alloy were measured during a non-protective heating and melting process. Two inflection points with rapid increase in temperature were found on both curves, which corresponded to the formation of “auliflower”oxide on the surface and the occurrence of flame during melting. These two temperatures are therefore defined as oxidation point and ignition point, respectively. The interior temperature-time curve is similar to that measured on the surface except for a comparable time delay. The oxidation and ignition temperatures increase with Ce content, an average increase of 33=and 61= was found when Ce addition was about 1.0 wt %. However, the increasing rate of the oxidation and ignition temperature decreases with increasing Ce content. An addition of 0.6wt% Ce is recommended for ignition-resistant AZ91 magnesium alloy.

  18. Effect of cerium on ignition point of AZ91D magnesium alloy

    Institute of Scientific and Technical Information of China (English)

    Zhao Hongjin; Zhang Yinghui; Kang Yonglin

    2008-01-01

    The surface and interior temperature-time curves of blocky cerium modified AZ91D magnesium alloy were measured during a non-protective heating and melting process. Two inflection points with rapid increase in temperature were found on both curves, which corresponded to the formation of "auliflower" oxide on the surface and the occurrence of flame during melting. These two temperatures are therefore defined as oxidation point and ignition point, respectively.The interior temperature-time curve is similar to that measured on the surface except for a comparable time delay. The oxidation and ignition temperatures increase with Ce content, an average increase of 33℃ and 61℃ was found when Ce addition was about 1.0 wt %. However, the increasing rate of the oxidation and ignition temperature decreases with increasing Ce content. An addition of 0.6wt% Ce is recommended for ignition-resistant AZ91 magnesium alloy.

  19. Domain Structure in Calcium-Cerium Fluorocarbonate Minerals, Mianning County, Sichuan Province, China

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The domain structures in calcium-cerium fluorocarbonate mineral series from a rare earth mineral deposit within an aegirine alkali granite massif in Mianning County, Sichuan Province, China, were studied by means of transmission electron microscopy. Many categories of domain structures in this mineral series were observed and investigated, including the microtwin domains of parisite-6R2 and B2S-6R, the antiphase domains of B2S-2H. The results show that the antiphase domains which are faults along crystal plane (0001) are formed by the displacement of crystal lattice in c* direction and the displacement is 0.471 nm. A new polytype (B4S2-3R) of regular mixed-layer structure with B4S2 type is found in the domain region of mixed-layer structure.

  20. Synthesis and properties of solid complexes of lanthanum, cerium. neodymium and erbium with N-phosphonomethylglicyne

    International Nuclear Information System (INIS)

    Water soluble complexes of lanthanum(III), cerium(III), neodymium(III) and erbium(III) with N-phosphonomethylglycine (glyphosate, NMPG) of the general formulae: LaC3H5NO5P·H2O, CeC3H5NO5P·H2O, NdC3H5NO5P·1.5H2O, ErC3H5NO5P·2H2O were synthesized. The solubility in water was determined. Thermal, diffractometric and IR spectrophotometric analyses were carried out. It was found that the lanthanide ions are bonded to N-phosphonmethylglycine through the oxygen atoms of the carboxylic and phosphonate groups and the nitrogen atom of the amine group. The final products of thermal decomposition at 900 oC were determined. (author)

  1. Electrospun cerium nitrate/polymer composite fibres:synthesis, characterization and fibre-division model

    Institute of Scientific and Technical Information of China (English)

    Li Meng-Meng; Long Yun-Ze; Yin Hong-Xing; Zhang Zhi-Ming

    2011-01-01

    Cerium (III)nitrate/poly(vinylpyrrolidone)(Ce(NO3)3/PVP)composite fibres have been prepared by electrospinning. After calcining the composite fibres in air at 500℃, CeO2 nanowires were obtained. The characterizations of the as-spun composite fibres and resultant nanowires have been carried out by a scanning electron microscope (SEM),an infrared spectrometer, an x-ray diffractometer and a fluorescence spectrophotometer. Interestingly, some unusual ribbon-like or twin fibres were observed besides the common fibres with circular or elliptic cross sections. We developed a fibre-division model resulting from Coulomb repulsion and solvent vaporization to interpret the formation of the ribbona or twin fibres, which has been confirmed by the SEM studies. Our results also indicate that the formation of the ribbons or twin fibres is less dependent on operation voltage and work distance.

  2. Optical Evidence of Itinerant-Localized Crossover of 4f Electrons in Cerium Compounds

    Science.gov (United States)

    Kimura, Shin-ichi; Kwon, Yong Seung; Matsumoto, Yuji; Aoki, Haruyoshi; Sakai, Osamu

    2016-08-01

    Cerium (Ce)-based heavy-fermion materials have a characteristic double-peak structure (mid-IR peak) in the optical conductivity [σ(ω)] spectra originating from the strong conduction (c)-f electron hybridization. To clarify the behavior of the mid-IR peak at a low c-f hybridization strength, we compared the σ(ω) spectra of the isostructural antiferromagnetic and heavy-fermion Ce compounds with the calculated unoccupied density of states and the spectra obtained from the impurity Anderson model. With decreasing c-f hybridization intensity, the mid-IR peak shifts to the low-energy side owing to the renormalization of the unoccupied 4f state, but suddenly shifts to the high-energy side owing to the f-f on-site Coulomb interaction at a slight localized side from the quantum critical point (QCP). This finding gives us information on the change in the electronic structure across QCP.

  3. Diffusion of Barium, Strontium and Cerium in Various Grades of Reactor Graphite

    International Nuclear Information System (INIS)

    Experiments designed to study the diffusion of barium, strontium and cerium in various grades of graphite of interest to the Dragon reactor project will be described. In these experiments specimens of the graphite are immersed in the vapour of the fission product metal under controlled conditions of temperature and pressure for known periods of time. After appropriate grinding and polishing, the distribution of the solute metal in the specimen is determined by means of an electron microprobe. The electron microprobe recordings are then interpreted to obtain apparent values of the diffusion coefficients and their dependence upon temperature. The results indicate that migration occurs primarily via defects in the graphite structure, with only a negligible contribution from in-grain diffusion. The significance of the results is discussed, with particular reference to the differences in behaviour encountered between various grades of graphite. (author)

  4. Study on Electrochemical Characteristics of Electroless Co-Ni-B Alloy with Cerium

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The effects of rare earth element cerium on composition and electrochemical characteristics of electroless Co-Ni-B alloy were studied in this paper. The alloy component was analyzed using Inductively Coupled Plasma (ICP). The plating rate is was determined by electronic balance. The cathode polarization curves and cyclic voltammogram during the electroless deposition were tested by LK998Ⅱmodel electrochemical analytical system. The results show that rare earth element Ce can co-deposit with cobalt-based alloy, and with mass increase of Ce added in aqueous solution, the contents of Co, Ni, Ce in alloy increase and the content of B decreases. Ce can increase deposition rate of alloy in some range. The rare earth makes deposition potential move to positive direction and makes polarizability decrease.

  5. Valence Control of Ce Ions in Cerium-substituted Yttrium Iron Garnet

    Institute of Scientific and Technical Information of China (English)

    SONG Fengbing; LI Qiang; ZHONG Zhifeng

    2005-01-01

    Cerium-substituted yttrium iron garnet(CexY3-xFe5O12, Ce∶YIG) was prepared via coprecipitation. The structure, morphology, valence state and constituent of Ce ions were investigated respectively. X-ray powder diffraction(XRD) analysis shows that Ce∶YIG was of single cubic YIG phase. The result of X-ray photoelectron spectroscopy(XPS) indicates the Ce ions in Ce∶YIG were in the state of trivalence. Scanning electron microscope(SEM) demonstrates the conglobation of Ce∶YIG particles about 0.2μm scale.The magnetic properties were studied by a vibrating sample magnetometer(VSM) and the result exhibits that substitution of Ce3+ changes the magnetic parameters of YIG. The effects of doping content of Ce ions and synthesis temperature on valence control were discussed in detail.

  6. Stability and morphology of cerium oxide surfaces in an oxidizing environment: A first-principles investigation

    Science.gov (United States)

    Fronzi, Marco; Soon, Aloysius; Delley, Bernard; Traversa, Enrico; Stampfl, Catherine

    2009-09-01

    We present density functional theory investigations of the bulk properties of cerium oxides (CeO2 and Ce2O3) and the three low index surfaces of CeO2, namely, (100), (110), and (111). For the surfaces, we consider various terminations including surface defects. Using the approach of "ab initio atomistic thermodynamics," we find that the most stable surface structure considered is the stoichiometric (111) surface under "oxygen-rich" conditions, while for a more reducing environment, the same (111) surface, but with subsurface oxygen vacancies, is found to be the most stable one, and for a highly reducing environment, the (111) Ce-terminated surface becomes energetically favored. Interestingly, this latter surface exhibits a significant reconstruction in that it becomes oxygen terminated and the upper layers resemble the Ce2O3(0001) surface. This structure could represent a precursor to the phase transition of CeO2 to Ce2O3.

  7. Cerium-based binary and ternary oxides in the transesterification of dimethylcarbonate with phenol.

    Science.gov (United States)

    Dibenedetto, Angela; Angelini, Antonella; di Bitonto, Luigi; De Giglio, Elvira; Cometa, Stefania; Aresta, Michele

    2014-04-01

    Diphenyl carbonate (DPC) plays a key role in phosgene-free carbonylation processes. It can be produced by transesterification of dimethyl carbonate (DMC) with phenol in the presence of catalysts. Methyl phenyl carbonate (MPC) is first produced that is then converted into DPC by either disproportionation or further transesterification with phenol. Cerium-based bimetallic oxides (with the heterometal being niobium, iron, palladium, or aluminum) are used as catalysts in the transesterification of DMC to synthesize MPC. The catalytic activity is affected by the type and concentration of the heterometal. XPS, IR and elementary analyses are employed to characterize the new catalysts. Differently from pure oxides, the mixed oxides produce a significant increase of the conversion and selectivity towards MPC. PMID:24616260

  8. Cerium-activated sol–gel silica glasses for radiation dosimetry in harsh environment

    Science.gov (United States)

    El Hamzaoui, Hicham; Capoen, Bruno; Helou, Nissrine Al; Bouwmans, Géraud; Ouerdane, Youcef; Boukenter, Aziz; Girard, Sylvain; Marcandella, Claude; Duhamel, Olivier; Chadeyron, Geneviève; Mahiou, Rachid; Bouazaoui, Mohamed

    2016-04-01

    Cerium-doped silica glass has been prepared for ionizing radiation dosimetry applications, using the sol–gel route and densification under different atmospheres. In comparison with the glass densified under air atmosphere, the one obtained after sintering the xerogel under helium gas presents improved optical properties, with an enhancement of the photoluminescence quantum yield up to 33%, which is attributed to a higher Ce3+ ions concentration. Such a glassy rod has been jacketed in a quartz tube and then drawn at high temperature to a cane, which has been used as active material in a fibered remote x-ray radiation dosimeter. The sample exhibited a reversible linear radioluminescence intensity response versus the dose rate up to 30 Gy s‑1. These results confirm the potentialities of this material for in vivo or high rate dose remote dosimetry measurements.

  9. Dielectric studies on cerium doped BaLa2Ti3O10

    Directory of Open Access Journals (Sweden)

    Parshuram B. Abhange

    2015-12-01

    Full Text Available The BaLa2-xCexTi3O10 samples (with x = 0.2, 0.4, 0.6 and 0.8 were prepared by hydroxide co-precipitation method and finally sintered at 1150 °C. The structure of the prepared samples was characterized by XRD and SEM. The single phase material was confirmed only for the BaLa1.8Ce0.2Ti3O10 ceramics. However, at higher cerium concentration secondary phase was observed. The characteristic plate-like structure, having grains with submicrometer thickness and high aspect ratio, was clearly observed by SEM. The results of dielectric measurement suggest that the appropriate adjustment of doping (with x between 0.2 and 0.8 will give sufficient high dielectric constant at very low loss. The resistivity of samples decreases with increase in temperature indicating the normal semiconducting electrical behaviour.

  10. Extraction of Uranium and Cerium mixture with liquid membrane emulsion process using Tributylphosphate extractant

    International Nuclear Information System (INIS)

    As a membrane a mixture of surfactant (span-80), Tributylphosphate in kerosene and sodium carbonate was used. The feeder was a mixture of uranium and cerium solution with 418.88 ppm U and 101.81 ppm Ce concentration in nitrate acid. The variables investigated were % surfactant (1-8 %) percentage, rotary speed for membrane making (2,500-10,000 rpm) and the acidity of feeder (0.5-3 M). The experiment result were that the optimal concentration of surfactant 5 %, rotary speed 7,500 rpm and efficiency extraction (efeks-U = 23.65 %, efeks-Ce = 7.09 %) at 0.5 M nitric acid and the efficiency stripping (efstripp-U = 5.06 %, efstripp-Ce = 99.91 %) at 0.5 M nitric acid

  11. Redox-active cerium oxide nanoparticles protect human dermal fibroblasts from PQ-induced damage

    Directory of Open Access Journals (Sweden)

    Claudia von Montfort

    2015-04-01

    Full Text Available Recently, it has been published that cerium (Ce oxide nanoparticles (CNP; nanoceria are able to downregulate tumor invasion in cancer cell lines. Redox-active CNP exhibit both selective pro-oxidative and antioxidative properties, the first being responsible for impairment of tumor growth and invasion. A non-toxic and even protective effect of CNP in human dermal fibroblasts (HDF has already been observed. However, the effect on important parameters such as cell death, proliferation and redox state of the cells needs further clarification. Here, we present that nanoceria prevent HDF from reactive oxygen species (ROS-induced cell death and stimulate proliferation due to the antioxidative property of these particles.

  12. Photochemical reduction and oxidation of cerium(IV) porphyrin sandwich complexes

    Energy Technology Data Exchange (ETDEWEB)

    Radzki, S. [Department of Chemistry, M. Curie-Sklodowska University, Lublin (Poland); Giannotti, Ch. [Institut de Chimie des Substances Naturelles, CNRS, Gif-sur-Yvette (France)

    1996-12-31

    Irradiation of cerium(IV) complex of octaethyl bisporphyrin Ce[OEP(-2)]{sub 2} with visible light, in the presence of CCl{sub 4} as an electron acceptor, leads to their photooxidation and {pi} cation formation. The process was followed using electron absorption and magnetic circular dichroism spectroscopy. Electronic configuration in neutral mono- and bisporphyrin (sandwich) complexes were compared to the one of neutral species. Photoirradiation of sandwich octaethyl- and tetraphenyl bisporphyrins, in the presence of an electron donor (triethylamine) results in their photoreduction on different pathways. Formation of the [Ce(III)(TPP)(-2)TPP(-2)]{sup -} and [Ce(III)(OEP)(-1)(OEP)(-2)] complexes was followed by absorption and electron spin resonance spectroscopy. (author) 31 refs, 4 figs

  13. Effect of Cerium on the Viscosity of Liquid Fe-C Alloy of Eutectic Content

    Institute of Scientific and Technical Information of China (English)

    滕新营; 叶以富; 刘含莲; 王焕荣; 石志强; 耿浩然

    2002-01-01

    The viscosities of liquid Fe-4.30C and Fe-4.30C-Ce alloys were measured by oscillating crucible viscometer. The results show that viscosity of Fe-4.30C alloy changes from 5.50 to 8.30 MPa*s when the liquid is cooled from 1425 ℃ to the melting point. The abnormity of viscosity of Fe-4.30C alloy near the melting point is reasonable due to the formation of graphite. The addition of cerium especially with content higher than 0.21% causes an evidently decrease in viscosity for eutectic alloy resulting from increase of free volume and size decrease of atom cluster in the liquids. It can be concended that the existence of C-Ce compound contributes to the discontinuous of viscosity at 1340~1370 ℃ for the Fe-4.30C-Ce alloy by experinments with differential scanning calorimeter.

  14. Impact of electrolyte composition on the performance of the zinc-cerium redox flow battery system

    Science.gov (United States)

    Nikiforidis, Georgios; Berlouis, Léonard; Hall, David; Hodgson, David

    2013-12-01

    The zinc-cerium redox flow battery has the highest open circuit cell voltage (Ecell = 2.4 V) of all the common redox flow battery (RFB) systems being investigated. In this paper, carbon polymer composite materials based on polyvinyl ester and polyvinylidene difluoride are investigated as the negative electrode for this RFB system. Electrolyte composition, particularly on the negative side, is found to play a key role in maintaining high (˜90%) coulombic efficiencies for the different charge durations, from 10 min to 4 h, examined. Energy efficiencies >60% are obtained for temperatures in the range 45 °C-55 °C when the zinc ion concentration in the methanesulfonic acid electrolyte is 2.5 mol dm-3. No dependence of the energy efficiency on the flow velocity is found, over the range 7.5 cm s-1-13.5 cm-1.

  15. Nanoscale Hybrid Langmuir-Blodgett Films Based on Cerium-Substituted Heteropolymolybdate and Polyquinoline

    Institute of Scientific and Technical Information of China (English)

    王峥; 柳士忠; 杜祖亮; 胡振纲; 张洪杰

    2003-01-01

    Nanoscale hybrid organic/inorganic Langmuir-Blodgett films of cerium-substituted heteropolymolybdates(Ce-HPMo) and π-conjugated macromolecule poly(1,2-dihydro-2,2,4-trimethyl)quinoline(PQ) were obtained with auxiliary film-forming material stearic acid(SA) or octadecylamine(ODA). The surface pressure-area isotherms illuminate the formation of the hybrid LB films of PQ/ODA/Ce-HPMo and P Q/SA/Ce-HPMo. The different film-forming mechanism was discussed when the different auxiliary film-forming materials were used in the system. The absorption spectra indicate that the molecules of PQ and Ce-HPMo are incorporated into the LB films. Tapping-mode AFM image reveals a granular surface texture of nanosized Ce-substituted heteropolymolybdate. STM image shows that the conductivity is greatly improved after Ce-substituted heteropolymolybdates are incorporated in the films.

  16. Adsorption of Magnesium Sulfate from Desulfurization Industrial Wastewater by Nano-Cerium Loaded Recycled Aggregates.

    Science.gov (United States)

    Yoon, Hyung-Sun; Bak, Somi; Seo, Seong-Gyu; Choi, Jeongdong; Kim, Eun-Sik

    2016-02-01

    In this research, the recycled aggregates (RAs) from blast furnace were solidified with nano-cerium (Ce), and applied to reduce the ionic species (e.g., magnesium sulfate) in the desulfurization industrial wastewater. Static batch experiments were performed based on different loading of recycled aggregates. Sulfate sorption isotherm studies were performed by Langmuir adsorption model. The physical morphologies were determined using scanning electron microscope. The results presented that the partial ions were captured with the different loading of the recycled aggregates during the batch tests. It was observed that 8 hr batch reaction equilibrated the electrical conductivity reduction, and 13% mass loading was estimated an optimal dosage of adsorbent. This study showed the nano-Ce loaded RAs could reduce ionic species in wastewater, and expected to be an economical adsorbent for wastewater treatment process. PMID:27433701

  17. Equiatomic cerium intermetallics CeXX' with two p elements

    Energy Technology Data Exchange (ETDEWEB)

    Poettgen, Rainer [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie; Chevalier, Bernard [Bordeaux Univ., Pessac (France). Institut de Chimie de la Matiere Condensee de Bordeaux

    2015-07-01

    The equiatomic CeXX' phases (X and X' = elements of the 3{sup rd}, 4{sup th}, or 5{sup th} main group) extend the large series of CeTX intermetallics (T = electron-rich transition metal). These phases crystallize with simple structure types, i.e. ZrNiAl, TiNiSi, CeScSi, α-ThSi{sub 2}, AlB{sub 2}, and GdSi{sub 2}. In contrast to the CeTX intermetallics one observes pronounced solid solutions for the CeXX' phases. The main influence on the magnetic ground states results from the absence of d electrons. All known CeXX' phases show exclusively trivalent cerium and antiferro- or ferromagnetic ordering at low temperatures. The crystal chemical details and some structure-property relationships are reviewed.

  18. Distribution of Cerium Ion in Cordierite Ceramics and Its Effect on Structure of Cordierite Crystal

    Institute of Scientific and Technical Information of China (English)

    Shi Zhiming

    2004-01-01

    Cerium addition plays an important role in sintering, transformation and phasicochemical properties of cordierite ceramics. The present work aims at studying the distribution of Ce4+ in cordierite ceramics and its effect on the structure of cordierite crystal by means of differential thermal analysis (DTA), X-ray diffraction (XRD) and scanning electronic microscope (SEM) so as to clarify the behavior of Ce4+. Results show that Ce4+ can exist in two forms of CeO2 particles and solid solution in Ce4+ -modified cordierite ceramics by the sol-gel method. The CeO2 particles separately distribute in the cordierite matrix. Ce4+ dissolves little into cordierite crystal, resulting in a decrease of lattice constants ofthe crystal. This kind of distribution behavior of Ce4+ makes us to easily tailor the properties of the cordieritc ceramics.

  19. Structural Characteristics of Cerium Oxide Nanocrystals Prepared by the Microemulsion Method

    Institute of Scientific and Technical Information of China (English)

    J.Zhang; X.Ju; Z.Y.Wu; T.Liu; T.D.Hu; Y.N.Xie

    2001-01-01

    The aim of this work is to investigate the microstructure development of erium oxide nanocrystal,prepared by the microemulsion process,as a function of annealing temperature in air.Combined with the HRTEM and the thermogravimetric-differential thermal analysis in air.Combined withthe HRTEm and the thremogravimetric-differential thermal analysis(TG-DTA),the XRD patterns reveal that the sample annealed at 623 K is amorphous,and the formation of cerium oxide nanocrystal occurs above 773 K.The local structural and electronic properties in the nanocrystallization process are probed by X-ray absorption spectra (XAS) at the Ce L3 edge.It is found that the phase structure changes from triclinic to cubic (CeO2),and the electroic structure changes from Ce3 to Ce4 upon increasing the annealing temperature.

  20. Potential of using cerium oxide nanoparticles for protecting healthy tissue during accelerated partial breast irradiation (APBI).

    Science.gov (United States)

    Ouyang, Zi; Mainali, Madan Kumar; Sinha, Neeharika; Strack, Guinevere; Altundal, Yucel; Hao, Yao; Winningham, Thomas Andrew; Sajo, Erno; Celli, Jonathan; Ngwa, Wilfred

    2016-04-01

    The purpose of this study is to investigate the feasibility of using cerium oxide nanoparticles (CONPs) as radical scavengers during accelerated partial breast irradiation (APBI) to protect normal tissue. We hypothesize that CONPs can be slowly released from the routinely used APBI balloon applicators-via a degradable coating-and protect the normal tissue on the border of the lumpectomy cavity over the duration of APBI. To assess the feasibility of this approach, we analytically calculated the initial concentration of CONPs required to protect normal breast tissue from reactive oxygen species (ROS) and the time required for the particles to diffuse to various distances from the lumpectomy wall. Given that cerium has a high atomic number, we took into account the possible inadvertent dose enhancement that could occur due to the photoelectric interactions with radiotherapy photons. To protect against a typical MammoSite treatment fraction of 3.4Gy, 5ng·g(-1) of CONPs is required to scavenge hydroxyl radicals and hydrogen peroxide. Using 2nm sized NPs, with an initial concentration of 1mg·g(-1), we found that 2-10days of diffusion is required to obtain desired concentrations of CONPs in regions 1-2cm away from the lumpectomy wall. The resultant dose enhancement factor (DEF) is less than 1.01 under such conditions. Our results predict that CONPs can be employed for radioprotection during APBI using a new design in which balloon applicators are coated with the NPs for sustained/controlled in-situ release from within the lumpectomy cavity. PMID:27053452

  1. Decomposition processes and structural transformations of cerium propionate into nanocrystalline ceria at different oxygen partial pressures

    International Nuclear Information System (INIS)

    The structural transformations that occur when thermal treatments turn cerium propionate into nanocrystalline ceria have been analysed with thermoanalytical techniques (TG, DTA and MS) and with structural and magnetic characterization (HRTEM, SQUID and XRD) of the final and intermediate products. Attention has been paid to what occurs during the decomposition of propionate and how the process is affected by the furnace atmosphere (oxidizing or inert). In an oxidizing atmosphere, the decomposition of cerium propionate is triggered by the oxidation of Ce3+ to Ce4+. This reaction entails the loss of large unoxidized propionate fragments of the propionate ligands. As decomposition proceeds, the carbonaceous residue makes the oxygen transport inside the material more difficult and decomposition becomes diffusion limited. At this point, extensive oxidation of the residue begins until it is completely removed. Crystallization of CeO2 occurs simultaneously with decomposition. In these conditions, crystalline nanoparticles (diameter of 3–5 nm) can be obtained at a temperature as low as 300 °C. In an inert atmosphere, decomposition occurs in three steps. During the first step, one of the three propionate ligands is lost, with little oxidation of Ce3+, and is substituted by a hydroxyl group. The second step entails the loss of the remaining ligands with a substantial oxidation of Ce3+ to Ce4+. After this step, the intermediate product is, proposed as, a mixture of amorphous Ce(OH)3 and Ce(OH)4. Finally, the third step leads to conversion of the Ce hydroxide into crystalline CeO2. In an inert atmosphere, the process is less reproducible than in air and a carbonaceous residue remains in the product.

  2. Air, aqueous and thermal stabilities of Ce3+ ions in cerium oxide nanoparticle layers with substrates

    KAUST Repository

    Naganuma, Tamaki

    2014-01-01

    Abundant oxygen vacancies coexisting with Ce3+ ions in fluorite cerium oxide nanoparticles (CNPs) have the potential to enhance catalytic ability, but the ratio of unstable Ce3+ ions in CNPs is typically low. Our recent work, however, demonstrated that the abundant Ce3+ ions created in cerium oxide nanoparticle layers (CNPLs) by Ar ion irradiation were stable in air at room temperature. Ce valence states in CNPs correlate with the catalytic ability that involves redox reactions between Ce3+ and Ce4+ ions in given application environments (e.g. high temperature in carbon monoxide gas conversion and immersion conditions in biomedical applications). To better understand the mechanism by which Ce3+ ions achieve stability in CNPLs, we examined (i) extra-long air-stability, (ii) thermal stability up to 500 °C, and (iii) aqueous stability of Ce 3+ ions in water, buffer solution and cell culture medium. It is noteworthy that air-stability of Ce3+ ions in CNPLs persisted for more than 1 year. Thermal stability results showed that oxidation of Ce 3+ to Ce4+ occurred at 350 °C in air. Highly concentrated Ce3+ ions in ultra-thin CNPLs slowly oxidized in water within 1 day, but stability was improved in the cell culture medium. Ce 3+ stability of CNPLs immersed in the medium was associated with phosphorus adsorption on the Ce3+ sites. This study also illuminates the potential interaction mechanisms of stable Ce3+ ions in CNPLs. These findings could be utilized to understand catalytic mechanisms of CNPs with abundant oxygen vacancies in their application environments. © The Royal Society of Chemistry 2014.

  3. Structural and electronic properties of cerium from LDA+U calculations

    Directory of Open Access Journals (Sweden)

    F. Kheradmand

    2008-12-01

    Full Text Available  In this work structural, electronic and magnetic properties of alpha and gamma phases of cerium crystal have been calculated by means of the LDA and LDA+U methods. The equilibrium volume and magnetic moment obtained from the GGA approximation in agreement with the experiment are equal to 27.64 Å3 and 0.00018 µB, respectively. This agreement shows that the 4f electrons in alpha phase are itinerant due to the use of the GGA, where no strong correlations have been yet thaken into account. We have observed that even after applying the GGA+U method with U = 6.1 eV, the density of states of f orbital remains still at Fermi surface. Therefore, in complete accord with the experiment, our results show that the 4f electrons in the alpha phase are not localized. This is the case where the LDA and the GGA approximations could not describe the gamma phase properly. Indeed, physical properties of the gamma phase is consistent with the experiment and could only be reproduced after applying LDA+U method with U = 4.4 eV. In this way, the value of equilibrium volume and magnetic moment calculated for the gamma phase were found to be 34.33 Å3 and 1.15 µB, respectively. After including correlations among 4f electrons the γ-Ce DOS is positioned at its more reasonable place lower than Fermi level compared with the DOS obtained from GGA calculations. Our results, then, show that the 4f electrons in the gamma phase, as opposed to the alpha phase, are localized which is indicative of the fact that gamma cerium is a strongly correlated system. The volume of 11 kbar has been obtained for the pressure of the alpha-gamma phase transition .

  4. Cerium oxide nanoparticles inhibit the migration and proliferation of gastric cancer by increasing DHX15 expression

    Directory of Open Access Journals (Sweden)

    Xiao YF

    2016-07-01

    Full Text Available Yu-Feng Xiao,1 Jian-Mei Li,2 Su-Min Wang,1 Xin Yong,1 Bo Tang,1 Meng-Meng Jie,1 Hui Dong,1 Xiao-Chao Yang,2 Shi-Ming Yang1 1Department of Gastroenterology, Xinqiao Hospital, Third Military Medical University, Chongqing, People’s Republic of China; 2School of Biomedical Engineering, Third Military Medical University, Chongqing, People’s Republic of China Abstract: Gastric cancer is one of the leading causes of tumor-related deaths in the world. Current treatment options do not satisfy doctors and patients, and new therapies are therefore needed. Cerium oxide nanoparticles (CNPs have been studied as a potential therapeutic approach for treating many diseases. However, their effects on human gastric cancer are currently unknown. Therefore, in this study, we aimed to characterize the effects of CNPs on human gastric cancer cell lines (MKN28 and BGC823. Gastric cancer cells were cocultured with different concentrations of CNPs, and proliferation and migration were measured both in vitro and in vivo. We found that CNPs inhibited the migration of gastric cancer cells when applied at different concentrations, but only a relatively high concentration (10 µg/mL of CNPs suppressed proliferation. Furthermore, we found that CNPs increased the expression of DHX15 and its downstream signaling pathways. We therefore provide evidence showing that CNPs may be a promising approach to suppress malignant activity of gastric cancer by increasing the expression of DHX15. Keywords: cerium oxide nanoparticles, gastric cancer, DHX15, p38

  5. Effect of calcination temperature on the crystallite growth of cerium oxide nano-powders prepared by the co-precipitation process

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Jian-Chih [Department of Orthopaedics, Kaohsiung Medical University Hospital, Kaohsiung 807, Taiwan (China); Chen, Wen-Cheng [School of Dentistry, College of Dental Medicine, Kaohsiung Medical University, Kaohsiung 807, Taiwan (China); Tien, Yin-Chun [Department of Orthopaedics, Kaohsiung Medical University Hospital, Kaohsiung 807, Taiwan (China); Shih, Chi-Jen, E-mail: cjshih@kmu.edu.t [Department of Fragrance and Cosmetics Science, Kaohsiung Medical University, 100 Shi-Chuan1st Road, Kaohsiung 80708, Taiwan (China)

    2010-04-30

    Cerium oxide nanocrystallites were synthesized by a co-precipitation process at a relatively low temperature, using cerium (III) nitrate as the starting material in a water solution with pH in the range of 8-9. The effect of calcination temperature on the crystallite growth of cerium oxide nano-powders was investigated by X-ray diffraction, transmission electron microscopy and electron diffraction. The crystallization temperature of the cerium oxide powders was estimated to be about 273 K, by XRD analysis. When calcined at temperatures from 473 to 1273 K, face-centered cubic phase crystallization was observed by XRD. The crystallite size of the cerium oxide increased from 12.0 to 48 nm as the calcining temperature increased from 473 to 1273 K, in the pH range 8-9. The activation energy for the growth of cerium oxide nanoparticles was found to have very low values of 17.5 kJ/mol for pH = 8 and 16.0 kJ/mol for pH = 9.

  6. Effect of calcination temperature on the crystallite growth of cerium oxide nano-powders prepared by the co-precipitation process

    International Nuclear Information System (INIS)

    Cerium oxide nanocrystallites were synthesized by a co-precipitation process at a relatively low temperature, using cerium (III) nitrate as the starting material in a water solution with pH in the range of 8-9. The effect of calcination temperature on the crystallite growth of cerium oxide nano-powders was investigated by X-ray diffraction, transmission electron microscopy and electron diffraction. The crystallization temperature of the cerium oxide powders was estimated to be about 273 K, by XRD analysis. When calcined at temperatures from 473 to 1273 K, face-centered cubic phase crystallization was observed by XRD. The crystallite size of the cerium oxide increased from 12.0 to 48 nm as the calcining temperature increased from 473 to 1273 K, in the pH range 8-9. The activation energy for the growth of cerium oxide nanoparticles was found to have very low values of 17.5 kJ/mol for pH = 8 and 16.0 kJ/mol for pH = 9.

  7. A Putative Association of a Single Nucleotide Polymorphism in GPR126 with Aggressive Periodontitis in a Japanese Population

    Science.gov (United States)

    Asano, Yoshihiro; Imai, Atsuko; Kawai, Shinji; Michikami, Ikumi; Yamashita, Motozo; Yamada, Satoru; Kitamura, Masahiro; Murakami, Shinya

    2016-01-01

    Periodontitis is an inflammatory disease causing loss of tooth-supporting periodontal tissue. Disease susceptibility to the rapidly progressive form of periodontitis, aggressive periodontitis (AgP), appears to be influenced by genetic risk factors. To identify these in a Japanese population, we performed whole exome sequencing of 41 unrelated generalized or localized AgP patients. We found that AgP is putatively associated with single nucleotide polymorphism (SNP) rs536714306 in the G-protein coupled receptor 126 gene, GPR126 [c.3086 G>A (p.Arg1029Gln)]. Since GPR126 activates the cAMP/PKA signaling pathway, we performed cAMP ELISA analysis of cAMP concentrations, and found that rs536714306 impaired the signal transactivation of GPR126. Moreover, transfection of human periodontal ligament (HPDL) cells with wild-type or mutant GPR126 containing rs536714306 showed that wild-type GPR126 significantly increased the mRNA expression of bone sialoprotein, osteopontin, and Runx2 genes, while mutant GPR126 had no effect on the expression of these calcification-related genes. The increase in expression of these genes was through the GPR126-induced increase of bone morphogenic protein-2, inhibitor of DNA binding (ID) 2, and ID4 expression. These data indicate that GPR126 might be important in maintaining the homeostasis of periodontal ligament tissues through regulating the cytodifferentiation of HPDL cells. The GPR126 SNP rs536714306 negatively influences this homeostasis, leading to the development of AgP, suggesting that it is a candidate genetic risk factor for AgP in the Japanese population. PMID:27509131

  8. In-gas-cell laser spectroscopy for magnetic dipole moment of $^{199}$Pt toward $N=$ 126

    CERN Document Server

    Hirayama, Y; Watanabe, Y X; Jeong, S C; Jung, H S; Kakiguchi, Y; Kimura, S; Moon, J Y; Oyaizu, M; Park, J H; Schury, P; Wada, M; Miyatake, H

    2016-01-01

    Magnetic dipole moment and mean-square charge radius of $^{199}$Pt ($I^{\\pi}=$ 5/2$^-$) have been evaluated for the first time from the investigation of the hyperfine splitting of the $\\lambda_1=$ 248.792 nm transition by in-gas-cell laser ionization spectroscopy. Neutron-rich nucleus $^{199}$Pt was produced by multi-nucleon transfer reaction at the KISS where the nuclear spectroscopy in the vicinity of $N=$ 126 is planed from the aspect of an astrophysical interest as well as the nuclear structure. Measured magnetic dipole moment $+$0.63(13)$\\mu_{\\rm N}$ is consistent with the systematics of those of nuclei with $I^{\\pi}=$ 5/2$^-$. The deformation parameter $|^{1/2}|$ evaluated from the isotope shift indicates the gradual shape change to spherical shape of platinum isotopes with increasing neutron number toward $N=$ 126.

  9. Biallelic Mutations in TMEM126B Cause Severe Complex I Deficiency with a Variable Clinical Phenotype.

    Science.gov (United States)

    Alston, Charlotte L; Compton, Alison G; Formosa, Luke E; Strecker, Valentina; Oláhová, Monika; Haack, Tobias B; Smet, Joél; Stouffs, Katrien; Diakumis, Peter; Ciara, Elżbieta; Cassiman, David; Romain, Nadine; Yarham, John W; He, Langping; De Paepe, Boel; Vanlander, Arnaud V; Seneca, Sara; Feichtinger, René G; Płoski, Rafal; Rokicki, Dariusz; Pronicka, Ewa; Haller, Ronald G; Van Hove, Johan L K; Bahlo, Melanie; Mayr, Johannes A; Van Coster, Rudy; Prokisch, Holger; Wittig, Ilka; Ryan, Michael T; Thorburn, David R; Taylor, Robert W

    2016-07-01

    Complex I deficiency is the most common biochemical phenotype observed in individuals with mitochondrial disease. With 44 structural subunits and over 10 assembly factors, it is unsurprising that complex I deficiency is associated with clinical and genetic heterogeneity. Massively parallel sequencing (MPS) technologies including custom, targeted gene panels or unbiased whole-exome sequencing (WES) are hugely powerful in identifying the underlying genetic defect in a clinical diagnostic setting, yet many individuals remain without a genetic diagnosis. These individuals might harbor mutations in poorly understood or uncharacterized genes, and their diagnosis relies upon characterization of these orphan genes. Complexome profiling recently identified TMEM126B as a component of the mitochondrial complex I assembly complex alongside proteins ACAD9, ECSIT, NDUFAF1, and TIMMDC1. Here, we describe the clinical, biochemical, and molecular findings in six cases of mitochondrial disease from four unrelated families affected by biallelic (c.635G>T [p.Gly212Val] and/or c.401delA [p.Asn134Ilefs(∗)2]) TMEM126B variants. We provide functional evidence to support the pathogenicity of these TMEM126B variants, including evidence of founder effects for both variants, and establish defects within this gene as a cause of complex I deficiency in association with either pure myopathy in adulthood or, in one individual, a severe multisystem presentation (chronic renal failure and cardiomyopathy) in infancy. Functional experimentation including viral rescue and complexome profiling of subject cell lines has confirmed TMEM126B as the tenth complex I assembly factor associated with human disease and validates the importance of both genome-wide sequencing and proteomic approaches in characterizing disease-associated genes whose physiological roles have been previously undetermined.

  10. Investigation on X-Radiation for 126 kV Vacuum Interrupters

    Institute of Scientific and Technical Information of China (English)

    YAN Jing; LIU Zhiyuan; GENG Yingsan; ZHANG Sheng; ZHANG Yingyao

    2016-01-01

    When subjected to high voltages between opened contacts,vacuum interrupters may emit X-rays.In order to ensure that these are of an acceptable level,vacuum interrupters should comply with the limits for X-ray emission and the test procedures to be carried out to verify this based on relevant standards and specifications.In this paper,a comprehensive experimental study has been performed for 126 kV vacuum interrupters used in a transmission system to understand the X-radiation level and its influence by three main parameters,namely applied power-frequency voltage,contact gap and power-frequency voltage conditioning.The radiation instrument is an FJ347 radiometer and the X-radiation dose was measured at the power-frequency test voltage.These tests demonstrated that the X-radiation emission level for a 126 kV vacuum interrupter did not exceed the following:5μSv per hour at a rated voltage of 126 kV and 150 μSv per hour at a power-frequency voltage of 230 kV at 1 m distance.The X-radiation dose increased with the applied power-frequency voltage increasing and decreased with the contact gap increasing.The X-radiation dose for 126 kV vacuum interrupters decreased by 57% after the conditioning procedure with a certain power-frequency voltage.During the conditioning procedure,the average value of the X-radiation dose was 4.49 mSv,which means if a professional conditions 180 interrupters per year,it will be safe at the 6.4 m distance.

  11. Investigation on X-Radiation for 126 kV Vacuum Interrupters

    Science.gov (United States)

    Yan, Jing; Liu, Zhiyuan; Geng, Yingsan; Zhang, Sheng; Zhang, Yingyao

    2016-05-01

    When subjected to high voltages between opened contacts, vacuum interrupters may emit X-rays. In order to ensure that these are of an acceptable level, vacuum interrupters should comply with the limits for X-ray emission and the test procedures to be carried out to verify this based on relevant standards and specifications. In this paper, a comprehensive experimental study has been performed for 126 kV vacuum interrupters used in a transmission system to understand the X-radiation level and its influence by three main parameters, namely applied power-frequency voltage, contact gap and power-frequency voltage conditioning. The radiation instrument is an FJ347 radiometer and the X-radiation dose was measured at the power-frequency test voltage. These tests demonstrated that the X-radiation emission level for a 126 kV vacuum interrupter did not exceed the following: 5 μSv per hour at a rated voltage of 126 kV and 150 μSv per hour at a power-frequency voltage of 230 kV at 1 m distance. The X-radiation dose increased with the applied power-frequency voltage increasing and decreased with the contact gap increasing. The X-radiation dose for 126 kV vacuum interrupters decreased by 57% after the conditioning procedure with a certain power-frequency voltage. During the conditioning procedure, the average value of the X-radiation dose was 4.49 mSv, which means if a professional conditions 180 interrupters per year, it will be safe at the 6.4 m distance. supported by National Key Basic Research Program of China (973 Program) (No. 2015CB251002)

  12. Biallelic Mutations in TMEM126B Cause Severe Complex I Deficiency with a Variable Clinical Phenotype.

    Science.gov (United States)

    Alston, Charlotte L; Compton, Alison G; Formosa, Luke E; Strecker, Valentina; Oláhová, Monika; Haack, Tobias B; Smet, Joél; Stouffs, Katrien; Diakumis, Peter; Ciara, Elżbieta; Cassiman, David; Romain, Nadine; Yarham, John W; He, Langping; De Paepe, Boel; Vanlander, Arnaud V; Seneca, Sara; Feichtinger, René G; Płoski, Rafal; Rokicki, Dariusz; Pronicka, Ewa; Haller, Ronald G; Van Hove, Johan L K; Bahlo, Melanie; Mayr, Johannes A; Van Coster, Rudy; Prokisch, Holger; Wittig, Ilka; Ryan, Michael T; Thorburn, David R; Taylor, Robert W

    2016-07-01

    Complex I deficiency is the most common biochemical phenotype observed in individuals with mitochondrial disease. With 44 structural subunits and over 10 assembly factors, it is unsurprising that complex I deficiency is associated with clinical and genetic heterogeneity. Massively parallel sequencing (MPS) technologies including custom, targeted gene panels or unbiased whole-exome sequencing (WES) are hugely powerful in identifying the underlying genetic defect in a clinical diagnostic setting, yet many individuals remain without a genetic diagnosis. These individuals might harbor mutations in poorly understood or uncharacterized genes, and their diagnosis relies upon characterization of these orphan genes. Complexome profiling recently identified TMEM126B as a component of the mitochondrial complex I assembly complex alongside proteins ACAD9, ECSIT, NDUFAF1, and TIMMDC1. Here, we describe the clinical, biochemical, and molecular findings in six cases of mitochondrial disease from four unrelated families affected by biallelic (c.635G>T [p.Gly212Val] and/or c.401delA [p.Asn134Ilefs(∗)2]) TMEM126B variants. We provide functional evidence to support the pathogenicity of these TMEM126B variants, including evidence of founder effects for both variants, and establish defects within this gene as a cause of complex I deficiency in association with either pure myopathy in adulthood or, in one individual, a severe multisystem presentation (chronic renal failure and cardiomyopathy) in infancy. Functional experimentation including viral rescue and complexome profiling of subject cell lines has confirmed TMEM126B as the tenth complex I assembly factor associated with human disease and validates the importance of both genome-wide sequencing and proteomic approaches in characterizing disease-associated genes whose physiological roles have been previously undetermined. PMID:27374774

  13. Analysis of Carotenoid Production by Halorubrum sp. TBZ126; an Extremely Halophilic Archeon from Urmia Lake

    Science.gov (United States)

    Naziri, Davood; Hamidi, Masoud; Hassanzadeh, Salar; Tarhriz, Vahideh; Maleki Zanjani, Bahram; Nazemyieh, Hossein; Hejazi, Mohammd Amin; Hejazi, Mohammad Saeid

    2014-01-01

    Purpose: Carotenoids are of great interest in many scientific disciplines because of their wide distribution, diverse functions and interesting properties. The present report describes a new natural source for carotenoid production. Methods: Halorubrum sp., TBZ126, an extremely halophilic archaeon, was isolated from Urmia Lack following culture of water sample on marine agar medium and incubation at 30 °C. Then single colonies were cultivated in broth media. After that the cells were collected and carotenoids were extracted with acetone-methanol (7:3 v/v). The identification of carotenoids was performed by UV-VIS spectroscopy and confirmed by thin layer chromatography (TLC) in the presence of antimony pentachloride (SbCl5). The production profile was analyzed using liquid-chromatography mass spectroscopy (LC-MS) techniques. Phenotypic characteristics of the isolate were carried out and the 16S rRNA gene was amplified using polymerase chain reaction (PCR). Results: LC-MS analytical results revealed that produced carotenoids are bacterioruberin, lycopene and β-carotene. Bacterioruberin was found to be the predominant produced carotenoid. 16S rRNA analysis showed that TBZ126 has 100% similarity with Halorubrum chaoviator Halo-G*T (AM048786). Conclusion: Halorubrum sp. TBZ126, isolated from Urmia Lake has high capacity in the production of carotenoids. This extremely halophilic archaeon could be considered as a prokaryotic candidate for carotenoid production source for future studies. PMID:24409411

  14. Small stress molecules inhibit aggregation and neurotoxicity of prion peptide 106-126

    International Nuclear Information System (INIS)

    In prion diseases, the posttranslational modification of host-encoded prion protein PrPc yields a high β-sheet content modified protein PrPsc, which further polymerizes into amyloid fibrils. PrP106-126 initiates the conformational changes leading to the conversion of PrPc to PrPsc. Molecules that can defunctionalize such peptides can serve as a potential tool in combating prion diseases. In microorganisms during stressed conditions, small stress molecules (SSMs) are formed to prevent protein denaturation and maintain protein stability and function. The effect of such SSMs on PrP106-126 amyloid formation is explored in the present study using turbidity, atomic force microscopy (AFM), and cellular toxicity assay. Turbidity and AFM studies clearly depict that the SSMs-ectoine and mannosylglyceramide (MGA) inhibit the PrP106-126 aggregation. Our study also connotes that ectoine and MGA offer strong resistance to prion peptide-induced toxicity in human neuroblastoma cells, concluding that such molecules can be potential inhibitors of prion aggregation and toxicity

  15. Panthenol-stabilized cerium dioxide nanoparticles for cosmeceutic formulations against ROS-induced and UV-induced damage.

    Science.gov (United States)

    Zholobak, N M; Shcherbakov, A B; Bogorad-Kobelska, A S; Ivanova, O S; Baranchikov, A Ye; Spivak, N Ya; Ivanov, V K

    2014-01-01

    A method of panthenol-stabilized cerium dioxide nanoparticles synthesis was developed and their effect on the survival rate of human epidermoid cancer cells HEp-2 and diploid epithelial swine testicular cell line (ST-cells) under oxidative stress conditions induced by hydrogen peroxide introduction and UV irradiation was studied. The results obtained indicate that the use of panthenol as a stabilizer supposedly provides a substantial increase in the efficiency of protection. The degree of protection is determined by panthenol-to-ceria molar ratio. The combination of panthenol and nano-ceria protects biological objects under study from reactive oxygen species (ROS) and UV-irradiation more effectively than individual panthenol or ceria. The protective action of panthenol-stabilized cerium dioxide nanoparticles depends strongly on their composition and the means of their application. PMID:24300997

  16. Real-time observation of dynamic process of oxygen vacancy migration in cerium oxides under electric field

    International Nuclear Information System (INIS)

    The dynamic process of oxygen vacancy migration driven by the external electric field is directly observed at atomic scale in the cerium oxides (CeO2) thin film by in-situ transmission electron microscopy method. When a bias voltage of a proper value is applied across the CeO2 film, the oxygen vacancies are formed near the interface of CeO2/anode, followed by their migration along the direction of the external electric field. The structural modulation occurs in the [110] zone axis due to the ordering of oxygen vacancies. The migration of oxygen vacancies results in the reversible structural transformation, i.e., releasing and storing oxygen processes in CeO2, which is of great significance for the ionic and electronic applications of the cerium oxides materials, such as oxygen pump, gas sensor, resistive random access memory, etc

  17. Synthesis of ordered cerium-doped cubic mesoporous silica using long-chain ionic liquid as template

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The long-chain ionic liquid 1-hexadecyl-3-methylimidazolium chloride (C16mimCl) was used as a template to prepare cerium-doped MCM-48 materials in basic medium by a hydrothermal synthesis procedure.The effect of the amount of Ce salt and C16mimCl/Si on the synthesis were discussed in detail.This mesoporous material exhibits a pore architecture which is cubic Ia3d gyroid and possesses a large surface area and a narrow pore distribution.Cerium in calcined porous framework exists in the form of well-dispersed tetrahedral coordination.The C16mimCl shows a high tendency toward selfaggregation that allows the formation of the ceriumdoped gyroid mesostructure by using the appropriate amount of Ce salt.

  18. Structure phase transformation and equation of state of cerium metal under pressures up to 51 GPa

    Science.gov (United States)

    Ce, Ma; Zuo-Yong, Dou; Hong-Yang, Zhu; Guang-Yan, Fu; Xiao, Tan; Bin, Bai; Peng-Cheng, Zhang; Qi-Liang, Cui

    2016-04-01

    This study presents high pressure phase transitions and equation of states of cerium under pressures up to 51 GPa at room temperature. The angle-dispersive x-ray diffraction experiments are carried out using a high energy synchrotron x-ray source. The bulk moduli of high pressure phases of cerium are calculated using the Birch–Murnaghan equation. We discuss and correct several previous controversial conclusions, which are caused by the measurement accuracy or personal explanation. The c/a axial ratio of ε-Ce has a maximum value at about 29 GPa, i.e., c/a ≈ 1.690. Project supported by the National Natural Science Foundation of China (Grant No. NSAF.U1330115) and the National Major Scientific Instrument and Equipment Development Project of China (Grant No. 2012YQ130234).

  19. Preparation and properties of a cerium-containing hydroxyapatite coating on commercially pure titanium by micro-arc oxidation

    Institute of Scientific and Technical Information of China (English)

    HUANG Yong; WANG Yingjun; NING Chengyun; NAN Kaihui; HAN Yong

    2008-01-01

    A porous cerium-containing hydroxyapatite coating on commercially pure titanium was prepared by micro-arc oxidation (MAO) in an electrolytic solution containing calcium acetate, β-glycerol phosphate disodium salt pentahydrate (β-GP), and cerium nitrate. The thickness, phase, composition morphology, and biocompatibility of the oxide coating were characterized by X-ray diffraction (XRD), electron probe microanalysis (EPMA), scanning electron microscopy (SEM) with energy dispersive X-ray spectrometer (EDS), and cell culture. The thickness of the MAO film is about 15-25μm, and the coating is porous and uneven, without any apparent interface to the titanium substrates. The results of XRD and EDS show that the porous coating is made up of hydroxyapatite (HA) film containing Ce. The favorable osteoblast cell affinity makes the Ce-HA film have a good biocompatibility. The Ce-HA film is expected to have significant medical applications as dental implants and artificial bone joints.

  20. Real-time observation of dynamic process of oxygen vacancy migration in cerium oxides under electric field

    Energy Technology Data Exchange (ETDEWEB)

    Li, Xiaomin; Qi, Kuo; Sun, Muhua; Huang, Qianming; Xu, Zhi, E-mail: xuzhi@iphy.ac.cn, E-mail: xdbai@iphy.ac.cn; Wang, Wenlong [Beijing National Laboratory for Condensed Matter Physics and Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China); Bai, Xuedong, E-mail: xuzhi@iphy.ac.cn, E-mail: xdbai@iphy.ac.cn [Beijing National Laboratory for Condensed Matter Physics and Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China); Collaborative Innovation Center of Quantum Matter, Beijing 100871 (China)

    2015-11-23

    The dynamic process of oxygen vacancy migration driven by the external electric field is directly observed at atomic scale in the cerium oxides (CeO{sub 2}) thin film by in-situ transmission electron microscopy method. When a bias voltage of a proper value is applied across the CeO{sub 2} film, the oxygen vacancies are formed near the interface of CeO{sub 2}/anode, followed by their migration along the direction of the external electric field. The structural modulation occurs in the [110] zone axis due to the ordering of oxygen vacancies. The migration of oxygen vacancies results in the reversible structural transformation, i.e., releasing and storing oxygen processes in CeO{sub 2}, which is of great significance for the ionic and electronic applications of the cerium oxides materials, such as oxygen pump, gas sensor, resistive random access memory, etc.

  1. Development of electrolytic process in molten salt media for light rare-earth metals production. The metallic cerium electrodeposition

    International Nuclear Information System (INIS)

    The development of molten salt process and the respective equipment aiming rare-earth metals recovery was described. In the present case, the liquid cerium metal electrodeposition in a molten electrolytes of cerium chloride and an equimolar mixture of sodium and potassium chlorides in temperatures near 800C was studied. Due the high chemical reactivity of the rare-earth metals in the liquid state and their molten halides, an electrolytic cell was constructed with controlled atmosphere, graphite crucibles and anodes and a tungsten cathode. The electrolytic process variables and characteristics were evaluated upon the current efficiency and metallic product purity. Based on this evaluations, were suggested some alterations on the electrolytic reactor design and upon the process parameters. (author). 90 refs, 37 figs, 20 tabs

  2. The biological effects of subacute inhalation of diesel exhaust following addition of cerium oxide nanoparticles in atherosclerosis-prone mice

    Energy Technology Data Exchange (ETDEWEB)

    Cassee, Flemming R., E-mail: flemming.cassee@rivm.nl [National Institute for Public Health and the Environment, PO box 1, 3720 BA Bilthoven (Netherlands); Campbell, Arezoo, E-mail: acampbell@westernu.edu [Western University of Health Sciences, Pomona, CA (United States); Boere, A. John F., E-mail: john.boere@rivm.nl [National Institute for Public Health and the Environment, PO box 1, 3720 BA Bilthoven (Netherlands); McLean, Steven G., E-mail: smclean1@staffmail.ed.ac.uk [BHF/University Centre for Cardiovascular Sciences, University of Edinburgh, Edinburgh (United Kingdom); Duffin, Rodger, E-mail: Rodger.Duffin@ed.ac.uk [MRC Centre for Inflammation Research, University of Edinburgh, Edinburgh (United Kingdom); Krystek, Petra, E-mail: petra.krystek@philips.com [Philips Innovation Services, Eindhoven (Netherlands); Gosens, Ilse, E-mail: Ilse.gosens@rivm.nl [National Institute for Public Health and the Environment, PO box 1, 3720 BA Bilthoven (Netherlands); Miller, Mark R., E-mail: Mark.Miller@ed.ac.uk [BHF/University Centre for Cardiovascular Sciences, University of Edinburgh, Edinburgh (United Kingdom)

    2012-05-15

    Background: Cerium oxide (CeO{sub 2}) nanoparticles improve the burning efficiency of fuel, however, little is known about health impacts of altered emissions from the vehicles. Methods: Atherosclerosis-prone apolipoprotein E knockout (ApoE{sup -/-}) mice were exposed by inhalation to diluted exhaust (1.7 mg/m{sup 3}, 20, 60 or 180 min, 5 day/week, for 4 weeks), from an engine using standard diesel fuel (DE) or the same diesel fuel containing 9 ppm cerium oxide nanoparticles (DCeE). Changes in hematological indices, clinical chemistry, atherosclerotic burden, tissue levels of inflammatory cytokines and pathology of the major organs were assessed. Results: Addition of CeO{sub 2} to fuel resulted in a reduction of the number (30%) and surface area (10%) of the particles in the exhaust, whereas the gaseous co-pollutants were increased (6-8%). There was, however, a trend towards an increased size and complexity of the atherosclerotic plaques following DE exposure, which was not evident in the DCeE group. There were no clear signs of altered hematological or pathological changes induced by either treatment. However, levels of proinflammatory cytokines were modulated in a brain region and liver following DCeE exposure. Conclusions: These results imply that addition of CeO{sub 2} nanoparticles to fuel decreases the number of particles in exhaust and may reduce atherosclerotic burden associated with exposure to standard diesel fuel. From the extensive assessment of biological parameters performed, the only concerning effect of cerium addition was a slightly raised level of cytokines in a region of the central nervous system. Overall, the use of cerium as a fuel additive may be a potentially useful way to limit the health effects of vehicle exhaust. However, further testing is required to ensure that such an approach is not associated with a chronic inflammatory response which may eventually cause long-term health effects.

  3. Cerium(Ⅳ) ammonium nitrate catalysed facile and efficient synthesis of polyhydroquinoline derivatives through Hantzsch multicomponent condensation

    Institute of Scientific and Technical Information of China (English)

    Cherkupally Sanjeeva Reddy; Mekala Raghu

    2008-01-01

    A general and convenient practical approach for the synthesis of polyhydroquinoline derivatives has been achieved via one-pot four-component Hantzsch condensation of aromatic aldehydes,dimedone,ethyl acetoacetate and ammonium acetate in the presence of a catalytic amount of cerium(Ⅳ) ammonium nitrate (CAN),in ethanol solvent at ambient temperature.Simple work-up,mild reaction conditions,inexpensive and non-toxic catalyst,and excellent product yields are the advantageous features of this method.

  4. Study on corrosion resistance of the BTESPT silane cooperating with rare earth cerium on the surface of aluminum-tube

    Institute of Scientific and Technical Information of China (English)

    肖围; 满瑞林; 缪畅; 彭天兰

    2010-01-01

    Bis-3-(triethoxysilyl)propyltetrasulfide(BTESPT) silane-rare earth cerium composite coatings on aluminum-tube were prepared at 60 °C by immersion method.The performance of composite coatings to protect the aluminum-tube against corrosion was investigated with potentiodynamic polarization curves,electrochemical impedance spectroscopy(EIS),and salt spray test(SST).The results of potentiodynamic polarization curves and EIS indicated that the self-corrosion current decreased by two orders of magnitude and the i...

  5. Correlation between the energy level structure of cerium-doped yttrium aluminum garnet and luminescent behavior at varying temperatures

    Science.gov (United States)

    Song, Zhen; Liu, Xiaolang; He, Lizhu; Liu, Q. L.

    2016-05-01

    Luminescent spectra of cerium-doped yttrium aluminum garnet are measured at varying temperatures. It is found that the two excitation peaks demonstrate a reverse trend as the temperature rises, and the breadth of the high-energy emission peak experiences an abrupt widening. These effects could be directly linked to the energy level scheme of Ce3+ under the crystal field of local symmetry. Moreover, an alternative fitting function is provided which could effectively resolve the emission curve.

  6. The biological effects of subacute inhalation of diesel exhaust following addition of cerium oxide nanoparticles in atherosclerosis-prone mice

    International Nuclear Information System (INIS)

    Background: Cerium oxide (CeO2) nanoparticles improve the burning efficiency of fuel, however, little is known about health impacts of altered emissions from the vehicles. Methods: Atherosclerosis-prone apolipoprotein E knockout (ApoE−/−) mice were exposed by inhalation to diluted exhaust (1.7 mg/m3, 20, 60 or 180 min, 5 day/week, for 4 weeks), from an engine using standard diesel fuel (DE) or the same diesel fuel containing 9 ppm cerium oxide nanoparticles (DCeE). Changes in hematological indices, clinical chemistry, atherosclerotic burden, tissue levels of inflammatory cytokines and pathology of the major organs were assessed. Results: Addition of CeO2 to fuel resulted in a reduction of the number (30%) and surface area (10%) of the particles in the exhaust, whereas the gaseous co-pollutants were increased (6–8%). There was, however, a trend towards an increased size and complexity of the atherosclerotic plaques following DE exposure, which was not evident in the DCeE group. There were no clear signs of altered hematological or pathological changes induced by either treatment. However, levels of proinflammatory cytokines were modulated in a brain region and liver following DCeE exposure. Conclusions: These results imply that addition of CeO2 nanoparticles to fuel decreases the number of particles in exhaust and may reduce atherosclerotic burden associated with exposure to standard diesel fuel. From the extensive assessment of biological parameters performed, the only concerning effect of cerium addition was a slightly raised level of cytokines in a region of the central nervous system. Overall, the use of cerium as a fuel additive may be a potentially useful way to limit the health effects of vehicle exhaust. However, further testing is required to ensure that such an approach is not associated with a chronic inflammatory response which may eventually cause long-term health effects.

  7. The effects of cerium doping concentration on the properties and photocatalytic activity of bimetallic Mo/Ce catalyst

    Science.gov (United States)

    Allaedini, Ghazaleh; Tasirin, Siti Masrinda; Aminayi, Payam

    2016-10-01

    In this study, the characterization and photocatalytic activity of MoO3 nanoparticles doped with various doping concentrations of cerium have been investigated. The Fourier transform infrared (FT-IR) spectra of the prepared catalysts confirmed that MoO3 particles have been successfully doped by cerium. Field emission scanning electron microscopy (FESEM) was performed to visualize the surface morphology of the obtained catalysts. The XRD patterns suggested that the crystallinity of the sample with the lowest doping concentration of 15 mol % was higher in comparison with samples of higher doping concentrations. The volume-averaged crystal sizes of the obtained catalysts were calculated to be 25, 28, and 32 nm for 15, 35, and 60 mol % samples, respectively. The photocatalytic activity along with the reaction kinetics of Ce-doped MoO3 nanoparticles have also been investigated through the dye degradation of methyl orange. The synthesized Ce-doped MoO3 particles with the lowest dopant concentration of 15 mol % exhibited the highest photocatalytic activity for methyl orange dye degradation. It was observed that photo-degradation activity decreased with an increase in the doping concentration of cerium. The predicted rate constants for samples with 15, 35, and 60 mol % doping concentrations were found to be 0.0432, 0.035, and 0.029 min-1, respectively.

  8. Study of cerium-promoted rhodium alumina catalyst as a steam reforming catalyst for treatment of spent solvents

    Institute of Scientific and Technical Information of China (English)

    Hee-Chul Yang; Min-Woo Lee; Ho-Sang Hwang; Jei-Kwon Moon; Dong-Yong Chung

    2014-01-01

    This study attempted to develop an appropriate catalyst used for the steam reforming of gasified spent solvents. Rh2O3/ CeO2-Al2O3 catalysts with various CeO2 loadings were prepared and heated at different temperatures of 500 and 800 ºC, and their surface properties were studied using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron mi-croscopy (TEM), temperature programmed reduction (TPR) and Brumauer-Emmett-Teller (BET) analyses. Rhodium existed in the form of Rh2O3, regardless of the sample composition as well as the heating temperature. In the tested range of cerium addition (up to 12 times the rhodium mass), no significant changes in BET surface areas and binding energy corresponding to Rh 3d5/2were observed. Instead, the addition of cerium led to a greatly enhanced dispersion of rhodium nanoparticles, and no agglomeration of rhodium was observed for samples heated even at 800 ºC. Honeycomb monolith rhodium catalysts promoted with cerium were fabricated and tested for the steam reforming of a gasified spent solvent, mainly consisting of butylene (C4H8). The test results suggested that a ce-rium-promoted rhodium catalyst could be used as an appropriate reforming catalyst for treating low-quality non-methane hydrocar-bons without the formation of coke at high temperatures of up to 900 ºC.

  9. Study on cerium-doped nano-TiO2 coatings for corrosion protection of 316 L stainless steel

    Science.gov (United States)

    Li, Suning; Wang, Qian; Chen, Tao; Zhou, Zhihua; Wang, Ying; Fu, Jiajun

    2012-04-01

    Many methods have been reported on improving the photogenerated cathodic protection of nano-TiO2 coatings for metals. In this work, nano-TiO2 coatings doped with cerium nitrate have been developed by sol-gel method for corrosion protection of 316 L stainless steel. Surface morphology, structure, and properties of the prepared coatings were investigated by X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy and energy dispersive X-ray spectroscopy. The corrosion protection performance of the prepared coatings was evaluated in 3 wt% NaCl solution by using electrochemical techniques in the presence and absence of simulated sunlight illumination. The results indicated that the 1.2% Ce-TiO2 coating with three layers exhibited an excellent photogenerated cathodic protection under illumination attributed to the higher separation efficiency of electron-hole pairs and higher photoelectric conversion efficiency. The results also showed that after doping with an appropriate concentration of cerium nitrate, the anti-corrosion performance of the TiO2 coating was improved even without irradiation due to the self-healing property of cerium ions.

  10. Ternary Plutonium-Cerium-Nickel Alloys as a Possible Fuel for Fast Reactors with Liquid Metal Cores

    International Nuclear Information System (INIS)

    The authors present results of a study of ternary plutonium-cerium-nickel alloys. From metallographic. thermal and X-ray analyses of these ternary alloys they obtained the projection of the liquidus curve onto the concentration triangle and the contours of the phase regions of the phase diagram over the isothermal cross-section for 400°C. The existence is established of a continuous series of solid solutions between the intermetallic compounds CeNi and PuNi, The maximum solubility of plutonium in the compound Ce7Ni3 is approximately 47.0 at. %. In the plutonium-cerium-nickel system there is a ternary eutectic with its melting point at 480°C. The composition of this eutectic is as follows: 45 at. % plutonium, 30 at. % cerium and 25 at.% nickel. The authors assume the existence of a peritectic point, the composition of which is not accurately established. The alloys, which lie along the valley line connecting the binary eutectics in the CeNi, PuNi system have a melting point not higher than 470°C. These alloys have a promising future as a fuel for fast reactors with liquid metal cores. (author)

  11. Freshwater dispersion stability of PAA-stabilised cerium oxide nanoparticles and toxicity towards Pseudokirchneriella subcapitata

    Energy Technology Data Exchange (ETDEWEB)

    Booth, Andy, E-mail: andy.booth@sintef.no [SINTEF Materials and Chemistry, Trondheim N-7465 (Norway); Størseth, Trond [SINTEF Materials and Chemistry, Trondheim N-7465 (Norway); Altin, Dag [BioTrix, Trondheim N-7022 (Norway); Fornara, Andrea; Ahniyaz, Anwar [German Federal Institute for Risk Assessment (BfR), Department of Product Safety, Berlin (Germany); Jungnickel, Harald; Laux, Peter; Luch, Andreas [SP Chemistry, Materials and Surfaces, Drottning Kristinas vag 45, SE-11686 Stockholm (Sweden); Sørensen, Lisbet [SINTEF Materials and Chemistry, Trondheim N-7465 (Norway)

    2015-02-01

    An aqueous dispersion of poly (acrylic acid)-stabilised cerium oxide (CeO{sub 2}) nanoparticles (PAA-CeO{sub 2}) was evaluated for its stability in a range of freshwater ecotoxicity media (MHRW, TG 201 and M7), with and without natural organic matter (NOM). In a 15 day dispersion stability study, PAA-CeO{sub 2} did not undergo significant aggregation in any media type. Zeta potential varied between media types and was influenced by PAA-CeO{sub 2} concentration, but remained constant over 15 days. NOM had no influence on PAA-CeO{sub 2} aggregation or zeta potential. The ecotoxicity of the PAA-CeO{sub 2} dispersion was investigated in 72 h algal growth inhibition tests using the freshwater microalgae Pseudokirchneriella subcapitata. PAA-CeO{sub 2} EC{sub 50} values for growth inhibition (GI; 0.024 mg/L) were 2–3 orders of magnitude lower than pristine CeO{sub 2} EC{sub 50} values reported in the literature. The concentration of dissolved cerium (Ce{sup 3+}/Ce{sup 4+}) in PAA-CeO{sub 2} exposure suspensions was very low, ranging between 0.5 and 5.6 μg/L. Free PAA concentration in the exposure solutions (0.0096–0.0384 mg/L) was significantly lower than the EC{sub 10} growth inhibition (47.7 mg/L) value of pure PAA, indicating that free PAA did not contribute to the observed toxicity. Elemental analysis indicated that up to 38% of the total Cerium becomes directly associated with the algal cells during the 72 h exposure. TOF-SIMS analysis of algal cell wall compounds indicated three different modes of action, including a significant oxidative stress response to PAA-CeO{sub 2} exposure. In contrast to pristine CeO{sub 2} nanoparticles, which rapidly aggregate in standard ecotoxicity media, PAA-stabilised CeO{sub 2} nanoparticles remain dispersed and available to water column species. Interaction of PAA with cell wall components, which could be responsible for the observed biomarker alterations, could not be excluded. This study indicates that the increased

  12. Cytotoxicity and antibacterial activity of gold-supported cerium oxide nanoparticles

    Directory of Open Access Journals (Sweden)

    Suresh Babu K

    2014-11-01

    Full Text Available K Suresh Babu,1,† M Anandkumar,1,† TY Tsai,2 TH Kao,2 B Stephen Inbaraj,2 BH Chen2,31Centre for Nano Sciences and Technology, Madanjeet School of Green Energy Technologies, Pondicherry University, Kalapet, India; 2Department of Food Science, 3Graduate Institute of Medicine, Fu Jen University, Taipei, Taiwan†These authors contributed equally to this workBackground: Cerium oxide nanoparticles (CeO2 have been shown to be a novel therapeutic in many biomedical applications. Gold (Au nanoparticles have also attracted widespread interest due to their chemical stability and unique optical properties. Thus, decorating Au on CeO2 nanoparticles would have potential for exploitation in the biomedical field. Methods: In the present work, CeO2 nanoparticles synthesized by a chemical combustion method were supported with 3.5% Au (Au/CeO2 by a deposition-precipitation method. The as-synthesized Au, CeO2, and Au/CeO2 nanoparticles were evaluated for antibacterial activity and cytotoxicity in RAW 264.7 normal cells and A549 lung cancer cells. Results: The as-synthesized nanoparticles were characterized by X-ray diffraction, scanning and transmission electron microscopy, and ultraviolet-visible measurements. The X-ray diffraction study confirmed the formation of cubic fluorite-structured CeO2 nanoparticles with a size of 10 nm. All synthesized nanoparticles were nontoxic towards RAW 264.7 cells at doses of 0–1,000 µM except for Au at >100 µM. For A549 cancer cells, Au/CeO2 had the highest inhibitory effect, followed by both Au and CeO2 which showed a similar effect at 500 and 1,000 µM. Initial binding of nanoparticles occurred through localized positively charged sites in A549 cells as shown by a shift in zeta potential from positive to negative after 24 hours of incubation. A dose-dependent elevation in reactive oxygen species indicated that the pro-oxidant activity of the nanoparticles was responsible for their cytotoxicity towards A549 cells. In

  13. Steric and electronic effects of 1,3-disubstituted cyclopentadienyl ligands on metallocene derivatives of Cerium, Titanium, Manganese, and Iron

    Energy Technology Data Exchange (ETDEWEB)

    Sofield, C.D.

    2000-05-19

    Sterically demanding 1,3-disubstituted cyclopentadienyl ligands were used to modify the physical properties of the corresponding metallocenes. Sterically demanding ligands provided kinetic stabilization for trivalent cerium compounds. Tris(di-t-butylcyclopentadienyl)cerium was prepared and anion competition between halides and cyclopentadienyl groups which had complicated synthesis of the tris(cyclopentadienyl)compound was qualitatively examined. Bis(di-t-butylcyclopentadienyl)cerium methyl was prepared and its rate of decomposition, by ligand redistribution, to tris(di-t-butylcyclopentadienyl)cerium was shown to be slower than the corresponding rate for less sterically demanding ligands. Asymmetrically substituted ligands provided a symmetry label for examination of chemical exchange processes. Tris[trimethylsilyl(t-butyl)cyclopentadienyl]cerium was prepared and the rate of interconversion between the C1 and C3 isomers was examined. The enthalpy difference between the two distereomers is 7.0 kJ/mol. The sterically demanding cyclopentadienyl ligands ansa-di-t-butylcyclopentadiene (Me2Si[(Me3C)2C5H3]2), ansa-bis(trimethylsilyl)cyclopentadiene (Me2Si[(Me3Si)2C5H3]2) and tetra-t-butylfulvalene and metallocene derivatives of the ligands were prepared and their structures were examined by single crystal X-ray crystallography. The effect that substituents on the cyclopentadienyl ring have on the pi-electron system of the ligand was examined through interaction between ligand and metal orbitals. A series of 1,3-disubstituted manganocenes was prepared and their electronic states were determined by solid-state magnetic susceptibility, electron paramagnetic resonance, X-ray crystallography, and variable temperature UV-vis spectroscopy. Spin-equilibria in [(Me3C)2C5H3]2Mn and [(Me3C)(Me3Si)C5H3]2Mn were examined and indicate an enthalpy difference of 15 kJ/mol between the high-spin and low-spin forms. Cyclopentadienyl groups resistant to intramolecular oxidative addition

  14. Expression and function mechanism of microRNA-126 in esophageal squamous cell carcinoma%微小RNA-126在食管鳞癌中的表达及作用机制

    Institute of Scientific and Technical Information of China (English)

    李浩淼; 孟凡宇; 马军; 于永魁; 华胸怀; 秦建军; 李印

    2015-01-01

    Objective To investigated microRNA (miR)-126 expression and its potential targets in esophageal squamous cell carcinoma (ESCC).Methods The expression level of miR-126 was detected in cancerous and paired paracancerous tissues from 75 patients with ESCC,association between miR-126 level and clinicopathologic characteristics were analysised.Target analysis of miR-126 was predicted using online tools.The effect of miR-126 expression on target proteins was assessed through up/down miR-126 level in ESCC cell lines.Results The relative expression of miR-126 in ESCC tissues was 0.28 ± 0.32 and 0.45 ± 0.47 in normal tissues (P < 0.01).Low level of miR-126 was associated with tumor differentiation,lymph nodes metastasis,tumor in-depth,and TNM stages (P < O.05).Insulin receptor substrate-1 (IRS-1) was over-expressed and associated with cell differentiation (P <0.01).In ESCC cell line Eca9706,Eca109 and TE-1,miR-126 mimics down-regulated the expression of IRS-1 protein (0.785 ± 0.337,1.873 ± 0.684,1.938 ± 1.081) compared with non-treated control (1.188 ± 0.336,2.756 ± 1.097,3.028 ± 0.789,P < 0.01),whereas miR-126 inhibitors lead to the opposite results (2.543±0.610,5.182±1.897,5.940±0.997,P<0.01).Conclusion This study revealed that miR-126 is low-expressed in ESCC and acts as a tumor suppressor in the carcinogenesis of ESCC.IRS-1 was downstream targets of miR-126 in ESCC.%目的 观察微小RNA-126(miR-126)在食管鳞癌组织中的表达及其可能调控的靶基因.方法 采用实时定量反转录聚合酶链反应(RT-qPCR)法,检测75例患者食管鳞癌组织和其匹配的癌旁组织中miR-126的表达水平,应用软件预测miR-126的靶基因,免疫组织化学法分析靶蛋白在癌组织中的表达,在食管鳞癌细胞中提高或降低miR-126表达水平,验证其对靶基因的调控作用.结果 对75组配对标本分析,癌组织中miR-126的相对表达量为0.28±0.32,癌旁组织为0.45±0.47,差异有统计学意义(P<0

  15. Cerium Substitution in Yttrium Iron Garnet: Valence State, Structure, and Energetics

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Xiaofeng; Tavakoli, Amir H.; Sutton, Steve; Kukkadapu, Ravi K.; Qi, Liang; Lanzirotti, Anthony; Newville, Mathew; Asta, Mark D.; Navrotsky, Alexandra

    2014-01-28

    The garnet structure is a promising nuclear waste form because it can accommodate various actinide elements. Y3Fe5O12 (YIG) is a model composition for such substitutions. Since cerium (Ce) can be considered an analogue of actinide elements such as thorium (Th), plutonium (Pu), and uranium (U), studying the local structure and thermodynamic stability of Ce-substituted YIG (Ce:YIG) can provide insights into the structural and energetic aspects of large ion substitution in garnets. Single phases of yttrium iron garnet with Ce substitution up to 20 mol % (Y3-xCexFe5O12 with 0 ≤ x ≤ 0.2) were synthesized through a citrate-nitrate combustion method. The oxidation state of cerium was examined by X-ray absorption near edge structure spectroscopy (XANES); the oxidation state and site occupancy of Fe as a function of Ce loading also was monitored by 57Fe-Mössbauer spectroscopy. These measurements establish that Ce is predominantly in the trivalent state at low substitution levels, while a mixture of trivalent and tetravalent states are observed at higher concentrations. Fe was predominately trivalent and exists in multiple environments. High temperature oxide melt solution calorimetry was used to determine the enthalpy of formation of these Ce-substituted YIG garnets. The thermodynamic analysis demonstrated that, although there is an entropic driving force for the substitution of Ce for Y, the substitution reaction is enthalpically unfavorable. The experimental results are complemented by electronic structure calculations performed within the framework of density functional theory (DFT) with Hubbard-U corrections, which reproduce the observed increase in the tendency for tetravalent Ce to be present with higher loading of Ce. The DFT+U results suggest that the energetics underlying the formation of tetravalent Ce involves a competition between an unfavorable energy to oxidize Ce and reduce Fe, and a favorable contribution due to strain-energy reduction. The structural

  16. Effects of amorphous silica coating on cerium oxide nanoparticles induced pulmonary responses

    Science.gov (United States)

    Ma, Jane; Mercer, Robert R.; Barger, Mark; Schwegler-Berry, Diane; Cohen, Joel M.; Demokritou, Philip; Castranova, Vincent

    2015-01-01

    Recently cerium compounds have been used in a variety of consumer products, including diesel fuel additives, to increase fuel combustion efficiency and decrease diesel soot emissions. However, cerium oxide (CeO2) nanoparticles have been detected in the exhaust, which raises a health concern. Previous studies have shown that exposure of rats to nanoscale CeO2 by intratracheal instillation (IT) induces sustained pulmonary inflammation and fibrosis. In the present study, male Sprague–Dawley rats were exposed to CeO2 or CeO2 coated with a nano layer of amorphous SiO2 (aSiO2/CeO2) by a single IT and sacrificed at various times post-exposure to assess potential protective effects of the aSiO2 coating. The first acellular bronchoalveolar lavage (BAL) fluid and BAL cells were collected and analyzed from all exposed animals. At the low dose (0.15 mg/kg), CeO2 but not aSiO2/CeO2 exposure induced inflammation. However, at the higher doses, both particles induced a dose-related inflammation, cytotoxicity, inflammatory cytokines, matrix metalloproteinase (MMP)-9, and tissue inhibitor of MMP at 1 day post-exposure. Morphological analysis of lung showed an increased inflammation, surfactant and collagen fibers after CeO2 (high dose at 3.5 mg/kg) treatment at 28 days post-exposure. aSiO2 coating significantly reduced CeO2-induced inflammatory responses in the airspace and appeared to attenuate phospholipidosis and fibrosis. Energy dispersive X-ray spectroscopy analysis showed Ce and phosphorous (P) in all particle-exposed lungs, whereas Si was only detected in aSiO2/CeO2-exposed lungs up to 3 days after exposure, suggesting that aSiO2 dissolved off the CeO2 core, and some of the CeO2 was transformed to CePO4 with time. These results demonstrate that aSiO2 coating reduce CeO2-induced inflammation, phospholipidosis and fibrosis. PMID:26210349

  17. Interactive effects of cerium oxide and diesel exhaust nanoparticles on inducing pulmonary fibrosis

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Jane Y.C., E-mail: jym1@cdc.gov [Health Effects Laboratory Division, National Institute for Occupational Safety and Health, Morgantown, WV 26505 (United States); Young, Shih-Houng; Mercer, Robert R.; Barger, Mark; Schwegler-Berry, Diane [Health Effects Laboratory Division, National Institute for Occupational Safety and Health, Morgantown, WV 26505 (United States); Ma, Joseph K. [School of Pharmacy, West Virginia University, Morgantown, WV 26506 (United States); Castranova, Vincent [Health Effects Laboratory Division, National Institute for Occupational Safety and Health, Morgantown, WV 26505 (United States)

    2014-07-15

    Cerium compounds have been used as a fuel-borne catalyst to lower the generation of diesel exhaust particles (DEPs), but are emitted as cerium oxide nanoparticles (CeO{sub 2}) along with DEP in the diesel exhaust. The present study investigates the effects of the combined exposure to DEP and CeO{sub 2} on the pulmonary system in a rat model. Specific pathogen-free male Sprague–Dawley rats were exposed to CeO{sub 2} and/or DEP via a single intratracheal instillation and were sacrificed at various time points post-exposure. This investigation demonstrated that CeO{sub 2} induces a sustained inflammatory response, whereas DEP elicits a switch of the pulmonary immune response from Th1 to Th2. Both CeO{sub 2} and DEP activated AM and lymphocyte secretion of the proinflammatory cytokines IL-12 and IFN-γ, respectively. However, only DEP enhanced the anti-inflammatory cytokine IL-10 production in response to ex vivo LPS or Concanavalin A challenge that was not affected by the presence of CeO{sub 2}, suggesting that DEP suppresses host defense capability by inducing the Th2 immunity. The micrographs of lymph nodes show that the particle clumps in DEP + CeO{sub 2} were significantly larger than CeO{sub 2} or DEP, exhibiting dense clumps continuous throughout the lymph nodes. Morphometric analysis demonstrates that the localization of collagen in the lung tissue after DEP + CeO{sub 2} reflects the combination of DEP-exposure plus CeO{sub 2}-exposure. At 4 weeks post-exposure, the histological features demonstrated that CeO{sub 2} induced lung phospholipidosis and fibrosis. DEP induced lung granulomas that were not significantly affected by the presence of CeO{sub 2} in the combined exposure. Using CeO{sub 2} as diesel fuel catalyst may cause health concerns. - Highlights: • DEP induced acute lung inflammation and switched immune response from Th1 to Th2. • DEP induced lung granulomas were not affected by the presence of CeO{sub 2}. • CeO{sub 2} induced sustained lung

  18. MicroRNA-126 and epidermal growth factor-like domain 7-an angiogenic couple of importance in metastatic colorectal cancer. Results from the Nordic ACT trial

    DEFF Research Database (Denmark)

    Hansen, T F; Christensen, René dePont; Andersen, R F;

    2013-01-01

    from a randomised phase III study were included. The primary microRNA-126 (pri-miRNA-126) A24G single-nucleotide polymorphism and the mature miRNA-126 were analysed by PCR using genomic DNA (full blood) and formalin-fixed paraffin-embedded tissue sections, respectively. The epidermal growth factor...

  19. The prognostic value of microRNA-126 and microvessel density in patients with stage II colon cancer

    DEFF Research Database (Denmark)

    Hansen, Torben Frøstrup; Kjær-Frifeldt, Sanne; Morgenthaler, Søren;

    2014-01-01

    BACKGROUND: Angiogenesis plays a pivotal role in malignant tumour growth and the metastatic process. We analysed the prognostic value of two angiogenesis parameters, microRNA-126 (miRNA-126) and microvessel density (MVD), in a population based cohort of patients operated for stage II colon cancer...... = 0.051. The MVD estimate was not associated with either RF-CSS, p = 0.49, or OS, p = 0.94. CONCLUSION: The current population based study of patients operated for stage II colon cancer demonstrated correlations between several prognostic unfavourable characteristics and miRNA-126 and argues...... were correlated with recurrence-free cancer specific survival (RF-CSS) and overall survival (OS). RESULTS: Low miRNA-126 expression was significantly correlated to T4, high malignancy grade, tumour perforation, fixation, and the presence of microsatellite instability. A prognostic impact on OS...

  20. 对合成电路优化的126 W Doherty功率放大器%Optimized combining circuit for 126 W Doherty power amplifier

    Institute of Scientific and Technical Information of China (English)

    侯富诚; 宋贺伦; 曾大杰; 顾滕锋; 张耀辉

    2016-01-01

    Based on the RF LDMOS transistor and flange from the independent research, a power amplifier was developed for wireless communication as well as L band and S band radar system with high power and efficiency. On the basis of electric grounding and heat sinking, the input and output internal matching circuits were designed to increase the impedance of the transistor. Using the characteristics of the Doherty power amplifier for the backed off efficiency enhancement and internal matching for the invertion of impedance, a power amplifier with the performance of 398 W, 52% at peaking point and 126 W, 43% at 8 dB backed-off power average point was achieved. The optimized technique enhances the backoff efficiency of Doherty power amplifier, 16% relative increasment to common structure, and improves the radio frequency performance of the wireless communication system further.%基于自主研发的RF LDMOS功率晶体管以及散热法兰,设计了一款用于无线通讯以及L波段和S波段雷达系统的大功率高效率的功率放大器.在保证了器件的射频接地以及散热的前提下,在封装内部设计了输入内匹配和输出内匹配电路,提高了管芯的阻抗点以便于电路板匹配.利用Doherty功率放大器结构可以提高功率回退处效率的特点,结合输出内匹配对负载阻抗点的翻转作用,得到了一种结构优化的Doherty实现方案,在峰值功率处达到398 W的输出功率,52%的漏极效率;以及功率8 dB回退的平均功率处126 W的输出功率,43%的漏极效率.这种改进技术进一步提高了功率回退处的效率,相对普通Doherty功率放大器结构,性能提升了16%,改善了无线通信系统的射频性能.

  1. Mechanism of trace cerium in ultra-clean IF steel%微量稀土铈在超洁净IF钢中的作用

    Institute of Scientific and Technical Information of China (English)

    杨吉春; 栗宏伟; 周莉; 张剑; 刘南

    2015-01-01

    The existence forms of cerium in ultra-IF steel,in which the contents of oxygen and sulphur were both less than 0.000 6%,were studied by chemical analysis,thermodynamic calculation,micro-examination and hardness mea-surement. And the effects of cerium on Al2O3 inclusions,microstructure and hardness were discussed. The results show that,when the cerium content was between 0.006 1%and 0.009 3%,the solid solubility of cerium range from 0.004 1%to 0.006 7%. About seventy percent of cerium is in the form of solid solution,the rest of cerium is in the form of inclu-sions,and there is no Ce-Fe intermetallic compound in the steel. By adding cerium,Al2O3 inclusions are modified into smaller globular CeAlO3 inclusions. Cerium played a role in modifying inclusions in the steel. Cerium has the effect of re-fining the microstructures of the steel. The greater the amount of solid solution of cerium was,the finer the crystalline grains were. When the content of cerium are 0.006 1%and 0.009 3%,Rockwell hardness increases by 7.6%and 12.7%re-spectively compared with IF steel without cerium.%采用化学成分分析、热力学计算、显微观察、硬度测定的方法,研究了稀土铈在氧和硫质量分数均小于0.0006%的超洁净IF钢中的存在状态,以及铈对钢的Al2O3夹杂物、显微组织和硬度的影响机理。结果表明,当铈质量分数为0.0061%~0.0093%时,铈的固溶量为0.0041%~0.0067%,约70%的铈以固溶形态存在,其余的铈以夹杂物形态存在,钢中不存在铈铁金属间化合物。铈能够将Al2O3夹杂物转化为尺寸较小的球状CeAlO3夹杂物,具有变质夹杂物的作用。铈具有改善IF钢的显微组织的作用,钢中铈的固溶量越大,晶粒越细。与不含铈的IF钢相比,当钢中铈质量分数为0.0061%和0.0093%时,钢的洛氏硬度分别提高了7.6%和12.7%。

  2. Clinical Analyses of Senile Retrogressive Cardiovalvulopathy-Report of 126 Cases

    Institute of Scientific and Technical Information of China (English)

    Chen Cibin; Lu Xiong; Huang Peilan

    2005-01-01

    Objectives To investigate the clinical characteristics and the diagnostic methods of senile retrogressive cardiovalvulopathy(SRC). Methods Total 126 cases had heart murmurs or complicated with congestive heart failure were selected into study. The diagnosis of SRC was detected by Echocardiography (UCG), chest X-ray, electrocardiography(ECG)and clinical data. The characteristics of clinical data included symptoms, signs, heart function and the prognosis, the features of UCG included quantify and positions of valvulae in pathosis, index of heart function, and the special findings of chest X-ray and ECG were analysed. Results The murmurs were found in total 126 cases complicated with different heart sounds and in different intensity in auscultate, 119patients were complicated with acute or chronic heart failure in different levels of heart function from Ⅱ -Ⅳ(NYHA). All the patients were received UCG examination, 126 cases had different calcifications with different extent and single or mixed valves were involved. The left ventricle heart function of systole and diastole were impaired. The mean LVEF was (35 ±0.7)%, In chest X-ray test: The ratio between heart and chest in larger than 50% were found in 122 cases.The ECG examination in total 84 patients shown that atrial premature beats were in 65 patients, atrial fibrillation or atrial flutter in 75 patients, ventricle premature beats 41 patients. Conclusions The results suggest that elder patients with heart murmurs,congestive heart failure or cardiac arrhythmias should be advised to received a UCG examination, SRC should be considerd, and other heart disease should be distinguished by UCG.

  3. Microscopic description of quadrupole collectivity in neutron-rich nuclei across the N = 126 shell closure

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez-Guzman, R.; Sharma, M.M. [Kuwait University, Physics Department, Kuwait (Kuwait); Robledo, L.M. [Universidad Autonoma de Madrid, Departamento de Fisica Teorica, Madrid (Spain)

    2015-06-15

    The quadrupole collectivity in Nd, Sm, Gd, Dy, Er, Yb, Hf and W nuclei with neutron numbers 122 ≤ N ≤ 156 is studied, both at the mean field level and beyond, using the Gogny energy density functional. Besides the robustness of the N = 126 neutron shell closure, it is shown that the onset of static deformations in those isotopic chains with increasing neutron number leads to an enhanced stability and further extends the corresponding two-neutron drip lines far beyond what could be expected from spherical calculations. Independence of the mean-field predictions with respect to the particular version of the Gogny energy density functional employed is demonstrated by comparing results based on the D1S and D1M parameter sets. Correlations beyond mean field are taken into account in the framework of the angular momentum projected generator coordinate method calculation. It is shown that N = 126 remains a robust neutron magic number when dynamical effects are included. The analysis of the collective wave functions, average deformations and excitation energies indicate that, with increasing neutron number, the zero-point quantum corrections lead to dominant prolate configurations in the 0{sub 1} {sup +}, 0{sub 2} {sup +}, 2{sub 1} {sup +} and 2{sub 2} {sup +} states of the studied nuclei. Moreover, those dynamical deformation effects provide an enhanced stability that further supports the mean-field predictions, corroborating a shift of the r-process path to higher neutron numbers. Beyond mean-field calculations provide a smaller shell gap at N = 126 than the mean-field one in good agreement with previous theoretical studies. However, the shell gap still remains strong enough in the two-neutron drip lines. (orig.)

  4. Orbital parameters for the two young binaries VSB 111 and VSB 126

    Energy Technology Data Exchange (ETDEWEB)

    Karnath, N.; Prato, L.; Wasserman, L. H.; Skiff, B. A. [Lowell Observatory, 1400 West Mars Hill Road, Flagstaff, AZ 86001 (United States); Torres, Guillermo [Harvard-Smithsonian Center for Astrophysics, 60 Garden Street, Cambridge, MA 02138 (United States); Mathieu, R. D., E-mail: nicole@lowell.edu, E-mail: lprato@lowell.edu, E-mail: lhw@lowell.edu, E-mail: bas@lowell.edu, E-mail: gtorres@cfa.harvard.edu, E-mail: mathieu@astro.wisc.edu [Department of Astronomy, University of Wisconsin-Madison, Madison, WI 53706 (United States)

    2013-12-01

    We report orbital parameters for two low-mass, pre-main-sequence, double-lined spectroscopic binaries: VSB 111 and VSB 126. These systems were originally identified as single-lined on the basis of visible-light observations. We obtained high-resolution infrared spectra with the 10 m Keck II telescope, detected absorption lines of the secondary stars, and measured radial velocities of both components in the systems. The visible-light spectra were obtained with the 1.5 m Wyeth reflector at the Oak Ridge Observatory, the 1.5 m Tillinghast reflector at the F. L. Whipple Observatory, and the 4.5 m equivalent Multiple Mirror Telescope. The combination of our visible and infrared observations of VSB 111 leads to a period of 902.1 ± 0.9 days, an eccentricity of 0.788 ± 0.008, and a mass ratio of 0.52 ± 0.05. VSB 126 has a period of 12.9244 ± 0.0002 days, an eccentricity of 0.18 ± 0.02, and a mass ratio of 0.29 ± 0.02. Visible-light photometry, using the 0.8 m telescope at Lowell Observatory, provided rotation periods for the primary stars in both systems: 3.74 ± 0.02 days for VSB 111 and 5.71 ± 0.07 days for VSB 126. Both binaries are located in the young, active star-forming cluster NGC 2264 at a distance of ∼800 pc. The difference in the center-of-mass velocities of the two systems is consistent with the radial velocity gradient seen across NGC 2264. To test the evolutionary models for accuracy and consistency, we compare the stellar properties derived from several sets of theoretical calculations for pre-main-sequence evolution with our dynamical results.

  5. 腔内激光治疗下肢静脉曲张126

    Institute of Scientific and Technical Information of China (English)

    王群; 惠震; 王耕

    2008-01-01

    下肢慢性静脉功能不全(chronic venous insufficiency,CVI)是常见的血管外科疾病,临床症状主要表现为下肢静脉曲张。我院于2003年7月-2005年8月采用英国DIOMED激光治疗系统结合手术方法治疗下肢静脉曲张126例(178条患肢),近期疗效显著,现报告如下。

  6. First Measurement of Several β-Delayed Neutron Emitting Isotopes Beyond N=126.

    Science.gov (United States)

    Caballero-Folch, R; Domingo-Pardo, C; Agramunt, J; Algora, A; Ameil, F; Arcones, A; Ayyad, Y; Benlliure, J; Borzov, I N; Bowry, M; Calviño, F; Cano-Ott, D; Cortés, G; Davinson, T; Dillmann, I; Estrade, A; Evdokimov, A; Faestermann, T; Farinon, F; Galaviz, D; García, A R; Geissel, H; Gelletly, W; Gernhäuser, R; Gómez-Hornillos, M B; Guerrero, C; Heil, M; Hinke, C; Knöbel, R; Kojouharov, I; Kurcewicz, J; Kurz, N; Litvinov, Yu A; Maier, L; Marganiec, J; Marketin, T; Marta, M; Martínez, T; Martínez-Pinedo, G; Montes, F; Mukha, I; Napoli, D R; Nociforo, C; Paradela, C; Pietri, S; Podolyák, Zs; Prochazka, A; Rice, S; Riego, A; Rubio, B; Schaffner, H; Scheidenberger, Ch; Smith, K; Sokol, E; Steiger, K; Sun, B; Taín, J L; Takechi, M; Testov, D; Weick, H; Wilson, E; Winfield, J S; Wood, R; Woods, P; Yeremin, A

    2016-07-01

    The β-delayed neutron emission probabilities of neutron rich Hg and Tl nuclei have been measured together with β-decay half-lives for 20 isotopes of Au, Hg, Tl, Pb, and Bi in the mass region N≳126. These are the heaviest species where neutron emission has been observed so far. These measurements provide key information to evaluate the performance of nuclear microscopic and phenomenological models in reproducing the high-energy part of the β-decay strength distribution. This provides important constraints on global theoretical models currently used in r-process nucleosynthesis.

  7. Time history solution program, L225 (TEV126). Volume 1: Engineering and usage

    Science.gov (United States)

    Kroll, R. I.; Tornallyay, A.; Clemmons, R. E.

    1979-01-01

    Volume 1 of a two volume document is presented. The usage of the convolution program L225 (TEV 126) is described. The program calculates the time response of a linear system by convoluting the impulsive response function with the time-dependent excitation function. The convolution is performed as a multiplication in the frequency domain. Fast Fourier transform techniques are used to transform the product back into the time domain to obtain response time histories. A brief description of the analysis used is presented.

  8. Genetic factors influencing ferritin levels in 14,126 blood donors

    DEFF Research Database (Denmark)

    Sørensen, Erik; Rigas, Andreas S; Thørner, Lise W;

    2015-01-01

    AND METHODS: The effect of six single-nucleotide polymorphisms (SNPs) on ferritin levels in 14,126 blood donors were investigated in four genes: in Human Hemochromatosis Protein gene (HFE; rs1800562 and rs179945); in Transmembrane Protease gene, Serine 6 (TMPRSS6-regulating hepcidin; rs855791); in BTB domain...... with iron deficiency in women. Results for all other genetic variants were insignificant. CONCLUSION: Genetic variants associated with hemochromatosis may protect donors against depleted iron stores. In addition, we showed that presence of the T-allele at rs855791 in TMPRSS6 was associated with lower iron...

  9. No influence of a N=126 Neutron Shell Closure in Fission Fragment Mass Distributions

    CERN Document Server

    Chaudhuri, A; Banerjee, K; Bhattacharya, S; Sadhukhan, Jhilam; Kundu, S; Bhattacharya, C; Meena, J K; Mukherjee, G; Saha, A K; Asgar, Md A; Dey, A; Manna, S; Pandey, R; Rana, T K; Roy, P; Roy, T; Srivastava, V; Bhattacharya, P; Biswas, D C; Joshi, B N; Mahata, K; Shrivastava, A; Vind, R P; Pal, S; Behera, B R; Singh, Varinderjit

    2015-01-01

    Mass distributions of the fragments in the fission of $^{206}$Po and the N=126 neutron shell closed nucleus $^{210}$Po have been measured. No significant deviation of mass distributions has been found between $^{206}$Po and $^{210}$Po, indicating the absence of shell correction at the saddle point in both the nuclei, contrary to the reported angular anisotropy and pre-scission neutron multiplicity results. This new result provides benchmark data to test the new fission dynamical models to study the effect of shell correction on the potential energy surface at saddle point.

  10. The Constrained NMSSM with a 126 GeV Higgs boson: A global analysis

    OpenAIRE

    Kowalska, Kamila; Munir, Shoaib; Roszkowski, Leszek; Sessolo, Enrico Maria; Trojanowski, Sebastian; Tsai, Yue-Lin Sming

    2012-01-01

    We present the first global analysis of the Constrained NMSSM that investigates the impact of the recent discovery of a 126 GeV Higgs-like boson, of the observation of a signal for BR(B_s->\\mu^+\\mu^-), and of constraints on supersymmetry from ~5/fb of data accumulated at the LHC, as well as of other relevant constraints from colliders, flavor physics and dark matter. We consider three possible cases, assuming in turn that the discovered Higgs boson is: i) the lightest Higgs boson of the model...

  11. Beta Decays of Isotones with Neutron Magic Number of N=126 and R-process Nucleosynthesis

    CERN Document Server

    Suzuki, Toshio; Kajino, Toshitaka; Otsuka, Takaharu

    2011-01-01

    Beta decays of the isotones with N=126 are studied by shell model calculations taking into account both the Gamow-Teller (GT) and first-forbidden (FF) transitions. The FF transitions are found to be important to reduce the half-lives, by nearly twice to several times, from those by the GT contributions only. Possible implications of the short half-lives of the waiting point nuclei on the r-process nucleosynthesis during the supernova explosions are discussed. A slight shift of the third peak of the element abundances in the r-process toward higher mass region is found.

  12. First measurement of several $\\beta$-delayed neutron emitting isotopes beyond N=126

    CERN Document Server

    Caballero-Folch, R; Agramunt, J; Algora, A; Ameil, F; Arcones, A; Ayyad, Y; Benlliure, J; Borzov, I N; Bowry, M; Calvino, F; Cano-Ott, D; Cortés, G; Davinson, T; Dillmann, I; Estrade, A; Evdokimov, A; Faestermann, T; Farinon, F; Galaviz, D; García, A R; Geissel, H; Gelletly, W; Gernhäuser, R; Gómez-Hornillos, M B; Guerrero, C; Heil, M; Hinke, C; Knöbel, R; Kojouharov, I; Kurcewicz, J; Kurz, N; Litvinov, Y; Maier, L; Marganiec, J; Marketin, T; Marta, M; Martínez, T; Martínez-Pinedo, G; Montes, F; Mukha, I; Napoli, D R; Nociforo, C; Paradela, C; Pietri, S; Podolyák, Zs; Prochazka, A; Rice, S; Riego, A; Rubio, B; Schaffner, H; Scheidenberger, Ch; Smith, K; Sokol, E; Steiger, K; Sun, B; Taín, J L; Takechi, M; Testov, D; Weick, H; Wilson, E; Winfield, J S; Wood, R; Woods, P; Yeremin, A

    2015-01-01

    The $\\beta$-delayed neutron emission probabilities of neutron rich Hg and Tl nuclei have been measured together with $\\beta$-decay half-lives for 20 isotopes of Au, Hg, Tl, Pb and Bi in the mass region N$\\gtrsim$126. These are the heaviest species where neutron emission has been observed so far. These measurements provide key information to evaluate the performance of nuclear microscopic and phenomenological models in reproducing the high-energy part of the $\\beta$-decay strength distribution. In doing so, it provides important constraints to global theoretical models currently used in $r$-process nucleosynthesis.

  13. Absorption of PCB126 by upper airways impairs G protein-coupled receptor-mediated immune response

    Science.gov (United States)

    Shimada, Ana Lúcia B.; Cruz, Wesley S.; Loiola, Rodrigo A.; Drewes, Carine C.; Dörr, Fabiane; Figueiredo, Natália G.; Pinto, Ernani; Farsky, Sandra H. P.

    2015-10-01

    PCB126 is a dioxin-like polychlorinated biphenyl (PCB) environmental pollutant with a significant impact on human health, as it bioaccumulates and causes severe toxicity. PCB126-induced immune toxicity has been described, although the mechanisms have not been fully elucidated. In this study, an in vivo protocol of PCB126 intoxication into male Wistar rats by intranasal route was used, which has not yet been described. The intoxication was characterised by PCB126 accumulation in the lungs and liver, and enhanced aryl hydrocarbon receptor expression in the liver, lungs, kidneys, and adipose tissues. Moreover, an innate immune deficiency was characterised by impairment of adhesion receptors on blood leukocytes and by reduced blood neutrophil locomotion and oxidative burst activation elicited by ex vivo G protein-coupled receptor (GPCR) activation. Specificity of PCB126 actions on the GPCR pathway was shown by normal burst oxidative activation evoked by Toll-like receptor 4 and protein kinase C direct activation. Moreover, in vivo PCB180 intoxication did not alter adhesion receptors on blood leukocytes either blood neutrophil locomotion, and only partially reduced the GPCR-induced burst oxidative activation on neutrophils. Therefore, a novel mechanism of in vivo PCB126 toxicity is described which impairs a pivotal inflammatory pathway to the host defence against infections.

  14. The ERK signaling target RNF126 regulates anoikis resistance in cancer cells by changing the mitochondrial metabolic flux.

    Science.gov (United States)

    Yoshino, Seiko; Hara, Toshiro; Nakaoka, Hiroki J; Kanamori, Akane; Murakami, Yoshinori; Seiki, Motoharu; Sakamoto, Takeharu

    2016-01-01

    Loss of anchorage to the extracellular matrix leads to apoptosis (anoikis) in normal cells, but cancerous cells are usually resistant to such stress. Here we report the pivotal role of an E3 ubiquitin ligase, ring-finger protein 126 (RNF126), in the resistance of cancer cells to the stress associated with non-adherent conditions. Non-adherent cancer cells exhibited increased flux through the tricarboxylic acid cycle via increased conversion of pyruvate to acetyl-CoA. RNF126 was found to act as a ubiquitin ligase for pyruvate dehydrogenase kinases (PDKs), resulting in their proteasomal degradation. This decrease in PDK levels allowed pyruvate dehydrogenases to catalyze the conversion of pyruvate to acetyl-CoA. Moreover, depletion of RNF126 or increased expression of PDK1 in cancer cells suppressed colony formation in soft agar as well as tumorigenicity in mice. RNF126 expression in cancer cells was found to be under the control of the extracellular signal-regulated kinase signaling pathway, which is essential for anoikis resistance. Thus, RNF126 is an attractive molecule for treating cancer by selectively targeting anchorage-independent growth. PMID:27462466

  15. Prediction of yttrium, lanthanum, cerium, and neodymium leaching recovery from apatite concentrate using artificial neural networks

    Institute of Scientific and Technical Information of China (English)

    E. Jorjani; A.H. Bagherieh; Sh. Mesroghli; S. Chehreh Chelgani

    2008-01-01

    The assay and recovery of rare earth elements (REEs) in the leaching process is being determined using expensive analytical methods: inductively coupled plasma atomic emission spectroscopy (ICP-AES) and inductively coupled plasma mass spectroscopy (ICP-MS). A neural network model to predict the effects of operational variables on the lanthanum, cerium, yttrium, and neodymium recovery in the leaching of apatite concentrate is presented in this article. The effects of leaching time (10 to 40 min),pulp densities (30% to 50%), acid concentrations (20% to 60%), and agitation rates (100 to 200 r/min), were investigated and optimized on the recovery of REEs in the laboratory at a leaching temperature of 60οC. The obtained data in the laboratory optimization process were used for training and testing the neural network. The feed-forward artificial neural network with a 4-5-5-1 arrangement was capable of estimating the leaching recovery of REEs. The neural network predicted values were in good agreement with the experimental results. The correlations of R=1 in training stages, and R=0.971, 0.952, 0.985, and 0.98 in testing stages were a result of Ce, Nd, La, and Y recovery prediction respectively, and these values were usually acceptable. It was shown that the proposed neural network model accurately reproduced all the effects of the operation variables, and could be used in the simulation of a leaching plant for REEs.

  16. Preparation of Nano-TiO2 Doped with Cerium and Its Photocatalytic Activity

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Cerium-doped titanium dioxide nano-powders were prepared through the sol-gel method and the compound samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), and UV/Vis diffuse reflectance spectra (DRS). The photocatalytic activity was evaluated by photocatalytic degradation of phenol in water. The results of XRD, TEM, and DRS show that pure TiO2 and Ce-doped TiO2 powder crystallines are a mixture of anatase and rutile;the doping can retard the development of the grain size of TiO2 and decrease the diameter of TiO2 from more than 20nm of pure TiO2 to about 10 nm;the doped TiO2 can improve the light absorption of TiO2 and suitable doping content tends to move the DRS spectrum of TiO2 towards visible light, but too much doping is not good for the light absorption ability.The results of the photocatalytic experiments show that doping with Ce content of 0.08 % ~ 0.4 % can increase the photocatalytic activity of TiO2;however, doping with Ce content of 0.5 % ~ 2.5 % can significantly decrease the photocatalytic activity of TiO2. The favorite doping content is 0.4 % in the range of our experiments.

  17. Effects of cerium oxide nanoparticles on soil enzymatic activities and wheat grass nutrients uptake

    Science.gov (United States)

    Li, Biting; Chen, Yirui; Bai, Lingyun; Jacobson, Astrid; Darnault, Christophe

    2015-04-01

    The US National Science Foundation estimated that the use of nanomaterials and nanotechnology would reach a global market value of 1 million this year. Concomitant with the wide applications of nanoparticles is an increasing risk of adverse effects to the environment and human health. As a common nanomaterial used as a fuel catalyst and polish material, cerium (IV) oxide nanoparticles (CeO2 NP) were tested for their potential impact on soil health and plant growth. Through exposure by air, water, and solid deposition, nanoparticles may accumulate in soils and impact agricultural systems. The objectives of this research were to determine whether CeO2 NPs affect the growth of wheat grass and selected soil enzyme activities chose as indicators of soil health. Wheat grass was grown in plant boxes containing CeO2 NPs mixed with agricultural soil at different concentrations. Two control groups were included: one consisting of soil with plants but no CeO2 NPs, and one containing only soil, i.e., no NP or wheat plants added. The plants were grown for 10 weeks and harvested every two weeks in a laboratory under sodium growth lights. At the end of the each growing period, two weeks, soils were assayed for phosphatase, β-glucosidase, and urease activities, and NPK values. Spectrophotometer analyses were used to assess enzyme activities, and NPK values were tested by Clemson Agricultural Center. Wheat yields were estimated by shoot and root lengths and weights.

  18. Biodiesel production over thermal activated cerium modified Mg-Al hydrotalcites

    International Nuclear Information System (INIS)

    Heterogeneous basic catalysts can be used for biodiesel production. The performances of several types of such materials are described in the literature but small attention is given to its deactivation in reaction medium. This paper put in evidence that catalysts are not static identities in the reaction medium, and relates the physical characteristics of fresh and post reaction samples with deactivation mechanisms. Catalysts, tested during the methanolysis of soybean oil, were prepared by thermal activation of Ce modified Mg-Al hydrotalcites (Mg/Al = 3, Ce/Mg 0.03 (atomic ratio) presented FAME yields higher than 90%. Thermogravimetry analysis of post reaction catalysts evidenced that cerium influences the reaction mechanism. The post reaction catalysts evidenced that surface restructuring occurs during reaction with sizeable change of the elements distribution which as beneficial effect on the catalytic performances. -- Highlights: ► Basic heterogeneous catalysts have been tested during the methanolysis of soybean oil to produces biodiesel (FAME). ► Catalysts were prepared by thermal activation of Ce modified Mg-Al hydrotalcites. ► Samples prepared with Ce/Mg < 0.05 (molar ratio) showed hydrotalcite XRD patterns even after calcination. ► Ce promotes fast rehydration/restructuration of the hydrotalcite having a beneficial effect on the catalytic performances.

  19. Synthesis, characterization and thermal expansion measurements on uranium-cerium mixed oxides

    Science.gov (United States)

    Venkata Krishnan, R.; Panneerselvam, G.; Singh, Brij Mohan; Kothandaraman, B.; Jogeswararao, G.; Antony, M. P.; Nagarajan, K.

    2011-07-01

    Uranium-cerium mixed oxides (U 1-yCe y)O 2 ( y = 0.2, 0.4, 0.6, 0.8) were prepared by combustion synthesis using citric acid as the fuel. Sintering of the solid solutions was carried out at 1873 K under reduced atmosphere. From the room temperature XRD patterns of the sintered samples it was found that the solid solutions form single phase fluorite structure. The room temperature lattice parameters of (U 1-yCe y)O 2 ( y = 0.2, 0.4, 0.6, 0.8) are 0.5458, 0.5446, 0.5434 and 0.5422 nm respectively. Thermal expansion of (U 1-yCe y)O 2 ( y = 0.2, 0.4, 0.6, 0.8) in the temperature range 298-1973 K was measured by high temperature X-ray diffraction (HTXRD). The coefficients of thermal expansion increase with increase in CeO 2 content in the sample and the measured data in the temperature range 298-1973 K, for (U 1-yCe y)O 2 ( y = 0.2, 0.4, 0.6, 0.8) are 18.23, 19.91, 21.59, 23.29 × 10 -6 K -1, respectively.

  20. The low-aluminium cast iron of reduced silicon content treated with cerium mischmetal

    Directory of Open Access Journals (Sweden)

    M. S. Soiński

    2008-07-01

    Full Text Available The work presents the effect of cerium mischmetal used in quantities of 0.1 and 0.2 wt-% and ferrosilicon used in quantities from 0.5% to 1.5% on the alloy matrix and the shape of graphite precipitates in the low-aluminium cast iron from seven heats, basing on the examination of its structure. The hypereutectic cast iron of the relatively high carbon content (4.0÷4.2% at the prior-to-treatment silicon and manganese content equal to ca. 0.6% and ca. 0.04%, respectively, has been examined.It has been found that the performed treatment leads to the change in the alloy matrix from the nearly almost pearlitic to the ferritic-pearlitic one accompanied by changes in the shape of graphite precipitates. Due to applying both of the mentioned substances in the above stated amounts the graphite precipitates in cast iron have taken the shape of nodular and vermicular ones, and no presence of flake graphite has been revealed. A quantitative analysis of the performed treatment i.e. determining the fractions of graphite precipitates of different shapes has been possible by means of a computer image analyser.

  1. Preparation and evaluation of cerium oxide-bovine hydroxyapatite composites for biomedical engineering applications.

    Science.gov (United States)

    Gunduz, O; Gode, C; Ahmad, Z; Gökçe, H; Yetmez, M; Kalkandelen, C; Sahin, Y M; Oktar, F N

    2014-07-01

    The fabrication and characterization of bovine hydroxyapatite (BHA) and cerium oxide (CeO2) composites are presented. CeO2 (at varying concentrations 1, 5 and 10wt%) were added to calcinated BHA powder. The resulting mixtures were shaped into green cylindrical samples by powder pressing (350MPa) followed by sintering in air (1000-1300°C for 4h). Density, Vickers microhardness (HV), compression strength, scanning electron microscopy (SEM) and X-ray diffraction (XRD) studies were performed on the products. The sintering behavior, microstructural characteristics and mechanical properties were evaluated. Differences in the sintering temperature (for 1wt% CeO2 composites) between 1200 and 1300°C, show a 3.3% increase in the microhardness (564 and 582.75HV, respectively). Composites prepared at 1300°C demonstrate the greatest compression strength with comparable results for 5 and 10wt% CeO2 content (106 and 107MPa) which are significantly better than those for 1wt% and those that do not include any CeO2 (90 and below 60MPa, respectively). The results obtained suggest optimal parameters to be used in preparation of BHA and CeO2 composites, while also highlighting the potential of such materials in several biomedical engineering applications.

  2. Effect of cerium on photosynthetic characteristics of soybean seedling exposed to supplementary ultraviolet-B radiation

    Institute of Scientific and Technical Information of China (English)

    LIANG Chan-juan; HUANG Xiao-hua; ZHOU Qing

    2006-01-01

    Effects of cerium (Ce3+) on photosynthetic characteristics were investigated by hydroponics under laboratory conditions when soybean seedlings were exposed to two levels of supplementary UV-B radiation. UV-B radiation badly inhibited the photosynthesis in soybean seedling, leading to a reduction in net photosynthetic rate (Ph), Hill reaction activity, light saturated photosynthetic rate (Ps) and apparent quanta yield (AQY), as well as the CO2 and light saturated photosynthetic rate (Pm) and carboxulation efficiency (CE). On the contrary, Ce obviously promoted the photosynthesis of plants by increasing Hill reaction activity, accelerating electron transport and photophosphorylation, and enhancing carboxylation efficiency. For Ce+UV-B treatments,the values of photosynthetic parameters were still lower than those of the control, but obviously higher than those of UV-B treatment.The results indicated that Ce alleviated the inhibition of UV-B radiation on the photosynthesis in soybean seedling to a certain extent.In correlating of Pn with Hill activity, AQY and CE, we found that the changes of photosynthetic rate were mainly influenced by the regulating effect of Ce on Hill activity and AQY at low level (0.15 W/m2) of UV-B radiation, but were dominated by the regulating effect of Ce on CE at high level (0.45 W/m2). Thus, Ce could regulate many aspects in photosynthesis of soybean seedling under UV-B stress. The regulating mechanism was close related with the dosage of UV-B radiation.

  3. Cerium oxide nanoparticles inhibit the migration and proliferation of gastric cancer by increasing DHX15 expression

    Science.gov (United States)

    Xiao, Yu-Feng; Li, Jian-Mei; Wang, Su-Min; Yong, Xin; Tang, Bo; Jie, Meng-Meng; Dong, Hui; Yang, Xiao-Chao; Yang, Shi-Ming

    2016-01-01

    Gastric cancer is one of the leading causes of tumor-related deaths in the world. Current treatment options do not satisfy doctors and patients, and new therapies are therefore needed. Cerium oxide nanoparticles (CNPs) have been studied as a potential therapeutic approach for treating many diseases. However, their effects on human gastric cancer are currently unknown. Therefore, in this study, we aimed to characterize the effects of CNPs on human gastric cancer cell lines (MKN28 and BGC823). Gastric cancer cells were cocultured with different concentrations of CNPs, and proliferation and migration were measured both in vitro and in vivo. We found that CNPs inhibited the migration of gastric cancer cells when applied at different concentrations, but only a relatively high concentration (10 µg/mL) of CNPs suppressed proliferation. Furthermore, we found that CNPs increased the expression of DHX15 and its downstream signaling pathways. We therefore provide evidence showing that CNPs may be a promising approach to suppress malignant activity of gastric cancer by increasing the expression of DHX15. PMID:27486320

  4. Role of cerium, lanthanum, and strontium additions in an Al-Si-Mg (A356) alloy

    Energy Technology Data Exchange (ETDEWEB)

    Nabawy, Ahmed M.; Samuel, Agnes M.; Samuel, Fawzy H. [Universite du Quebec, Chicoutimi (Canada). Dept. des Sciences Appliquees; Alkahtani, Saleh A.; Abuhasel, Khaled A. [Salman Bin Abdulaziz Univ., Riyadh (Saudi Arabia). Mechanical Engineering Dept.

    2016-05-15

    The effects of individual and combined additions of cerium (Ce), lanthanum (La), and strontium (Sr) on the eutectic modification and solidification characteristics of an Al-Si-Mg (A356) aluminum alloy were investigated using optical microscopy and thermal analysis techniques. Addition of Ce, La, and Sr resulted in different depression levels of the eutectic nucleation temperature and eutectic growth undercooling, generating modified eutectic structures exhibiting different levels of modification. Microstructural results showed that the best modification levels using individual additions were achieved by Sr which produced a fine fibrous eutectic structure, followed by La, which produced a refined lamellar structure, with Ce providing the lowest level of modification. On the other hand, a combined addition of Ce and Sr provided the highest modification level, with the production of a very fine fibrous eutectic silicon structure. In general, the addition of Sr helped to further increase the refinement obtained in the alloys containing La or Ce + La additions. In the latter alloy, the main intermetallic phases observed were La(Al,Si){sub 2} and Al{sub 20}(La,Ce)Ti{sub 2}Si. The improved modification levels were found to be proportional to the depression in the eutectic nucleation temperature and the eutectic growth undercooling. A high cooling rate also improved the modification level by at least one level.

  5. A nanostructured cerium oxide film-based immunosensor for mycotoxin detection

    International Nuclear Information System (INIS)

    Rabbit-immunoglobulin antibodies (r-IgGs) and bovine serum albumin (BSA) have been immobilized onto sol-gel-derived nanostructured cerium oxide (nanoCeO2) film fabricated onto an indium-tin-oxide (ITO) coated glass plate to detect ochratoxin-A (OTA). Broad reflection planes obtained in x-ray diffraction (XRD) patterns reveal the formation of CeO2 nanostructures. Electrochemical studies reveal that nanoCeO2 particles provide an increased electroactive surface area for loading of r-IgGs with desired orientation, resulting in enhanced electron communication between r-IgGs and electrode. BSA/r-IgGs/nano CeO2/ITO immunoelectrode exhibits improved characteristics such as linear range (0.5-6 ng dl-1), low detection limit (0.25 ng dl-1), fast response time (30 s) and high sensitivity (1.27 μA ng-1 dl-1 cm-2). The high value of the association constant (Ka, 0.9 x 1011 l mol-1) indicates the high affinity of the BSA/r-IgGs/nanoCeO2/ITO immunoelectrode to OTA.

  6. Enhanced hydrogen desorption property of MgH{sub 2} with the addition of cerium fluorides

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Huai-Jun, E-mail: huaijun.lin.489@s.kyushu-u.ac.jp [School of Materials Science and Engineering, South China University of Technology, Guangzhou 510640 (China); Department of Mechanical Engineering, Faculty of Engineering, Kyushu University, Fukuoka 819-0395 (Japan); Matsuda, Junko [International Institute for Carbon-Neutral Energy Research (WPI-I2CNER), Kyushu University, Fukuoka 819-0395 (Japan); Li, Hai-Wen [International Institute for Carbon-Neutral Energy Research (WPI-I2CNER), Kyushu University, Fukuoka 819-0395 (Japan); International Research Center for Hydrogen Energy, Kyushu University, Fukuoka 819-0395 (Japan); Zhu, Min [School of Materials Science and Engineering, South China University of Technology, Guangzhou 510640 (China); China–Australia Joint Laboratory for Energy & Environmental Materials, South China University of Technology, Guangzhou 510640 (China); Akiba, Etsuo [Department of Mechanical Engineering, Faculty of Engineering, Kyushu University, Fukuoka 819-0395 (Japan); International Institute for Carbon-Neutral Energy Research (WPI-I2CNER), Kyushu University, Fukuoka 819-0395 (Japan); International Research Center for Hydrogen Energy, Kyushu University, Fukuoka 819-0395 (Japan)

    2015-10-05

    Highlights: • Activation energy of MgH{sub 2} desorption is remarkably reduced with the dopant of CeF{sub 4}. • The improvement might be attributed to new Ce–F–Mg species at the CeF{sub 4}/MgH{sub 2} interface. • Easy electron transfer induced from the high valence Ce-cation benefits MgH{sub 2} desorption. - Abstract: Hydrogen desorption property of MgH{sub 2} doped with cerium fluorides with different valences prepared using ball milling has been studied. CeF{sub 4} is catalytically active for hydrogen desorption of MgH{sub 2}. Hydrogen desorption temperature and apparent activation energy of MgH{sub 2} are significantly reduced with dopant of 2 mol% of CeF{sub 4}, which might be attributed to the formation of a new Ce–F–Mg specie at the CeF{sub 4}/MgH{sub 2} interface and the easy electron transfer induced from the high valence Ce-cation. The apparent activation energy of hydrogen desorption of MgH{sub 2} is reduced from ∼160 kJ/mol to ∼110 kJ/mol with the dopant of CeF{sub 4}.

  7. Preparation and investigation of structural, magnetic and microwave absorption properties of cerium doped barium hexaferrite

    Directory of Open Access Journals (Sweden)

    P Kameli

    2015-01-01

    Full Text Available In this study the structure, magnetic and microwave absorption properties of cerium (Ce doped barium hexaferrite with general formulae BaCexFe12-xO19 (x=0.0, 0.05, 0.1, 0.15, 0.2 have been investigated. These samples have been prepared by sol- gel method. Influence of replacing Fe+3 ion by rare- earth Ce+3 ion on the structural, magnetic and microwave absorption properties have been investigated by X- ray diffraction (XRD, Fourier transform infrared (FT-IR, Vibrating sample magnetometer (VSM and vector network analyzer (VNA. X-ray diffraction analysis indicated that the samples are of single phase with space group p63/mmc. The magnetic properties of samples indicated that with the Ce doping the saturation magnetization show no regular behavior. Moreover, coercivity (Hc first decreased and reached to the minimum value for x=0.1 sample and then increased with Ce content increasing. Also, measurement of electromagnetic wave absorption in X and Ku frequency bands indicated that the maximum of reflection loss obtained for x=0.15 sample. Moreover, result indicated that absorption peak shifted toward a lower frequency when thickness was increased.

  8. A spectrophotometric study of cerium IV and chromium VI species in nuclear fuel reprocessing process streams

    Science.gov (United States)

    Nickson, I. D.; Boxall, C.; Jackson, A.; Whillock, G. O. H.

    2010-03-01

    Nuclear fuel reprocessing schemes such as PUREX and UREX utilise HNO3 media. An understanding of the corrosion of process engineering materials such as stainless steel in such media is a major concern for the nuclear industry. Two key species are cerium and chromium which, as Ce(IV), Cr(VI), may act as corrosion accelerants. An on-line analytical technique for these quantities would be useful for determining the relationship between corrosion rate and [Ce(IV)] and [Cr(VI)]. Consequently, a strategy for simultaneous quantification of Ce(IV), Cr(VI) and Cr(III) in the presence of other ions found in average burn-up Magnox / PWR fuel reprocessing stream (Fe, Mg, Nd, Al) is being developed. This involves simultaneous UV-vis absorbance measurement at 620, 540, 450 nm, wavelengths where Ce and Cr absorb but other ions do not. Mixed solutions of Cr(VI) and Ce(IV) are found to present higher absorbance values at 540 nm than those predicted from absorbances recorded from single component solutions of those ions. This is attributed to the formation of a 3:1 Cr(VI)-Ce(IV) complex and we report on the complexation and UV-visible spectrophotometric characteristics of this species. To the best of our knowledge this is the first experimental study of this complex in aqueous nitric acid solution systems.

  9. Shifts in oxidation states of cerium oxide nanoparticles detected inside intact hydrated cells and organelles

    Energy Technology Data Exchange (ETDEWEB)

    Szymanski, Craig J.; Munusamy, Prabhakaran; Mihai, Cosmin; Xie, Yumei; Hu, Dehong; Gilles, Marry K.; Tyliszczak, T.; Thevuthasan, Suntharampillai; Baer, Donald R.; Orr, Galya

    2015-09-01

    Cerium oxide nanoparticles (CNPs) have been shown to induce diverse biological effects, ranging from toxic to beneficial. The beneficial effects have been attributed to the potential antioxidant activity of CNPs via certain redox reactions, depending on their oxidation state or Ce3+/Ce4+ ratio. However, this ratio is strongly dependent on the environment and age of the nanoparticles and it is unclear whether and how the complex intracellular environment impacts this ratio and the possible redox reactions of CNPs. To identify any changes in the oxidation state of CNPs in the intracellular environment and better understand their intracellular reactions, we directly quantified the oxidation states of CNPs outside and inside intact hydrated cells and organelles using correlated scanning transmission x-ray and super resolution fluorescence microscopies. By analyzing hundreds of small CNP aggregates, we detected a shift to a higher Ce3+/Ce4+ ratio in CNPs inside versus outside the cells, indicating a net reduction of CNPs in the intracellular environment. We further found a similar ratio in the cytoplasm and in the lysosomes, indicating that the net reduction occurs earlier in the internalization pathway. Together with oxidative stress and toxicity measurements, our observations identify a net reduction of CNPs in the intracellular environment, which is consistent with their involvement in potentially beneficial oxidation reactions, but also point to interactions that can negatively impact the health of cells.

  10. Characterization of the alumina film with cerium doped on the iron-aluminide diffusion coating

    Energy Technology Data Exchange (ETDEWEB)

    Zhan, Q., E-mail: zhanqin1983@163.com; Yang, H.G.; Zhao, W.W.; Yuan, X.M.; Hu, Y.

    2013-11-15

    An iron-aluminide layer with a thin alumina film on the top as a composite tritium permeation barrier (TPB) coating was characterized under different oxidation conditions. The TPB coating was prepared initially on a China Low Activation Ferritic-Martensitic (CLAM) steel by a pack cementation aluminizing process and then an alumina film was formed on the surface of this iron-aluminide diffusion layer by an oxidizing process. To modify the properties of the FeAl/Al{sub 2}O{sub 3} composite TPB coatings, the rare earth element (cerium) was introduced as a dopant while oxidizing. Characterization showed that a continuous oxide scale with a thickness of about 300–400 nm was formed on the FeAl diffusion layer. The film was mainly composed of Al{sub 2}O{sub 3} doped with a little CeO{sub 2}. In addition, the concentration of α-Al{sub 2}O{sub 3} increased with elevated temperature while oxidizing. The phase transformation behavior of alumina scale on the surface of an iron-aluminide layer was studied in this paper.

  11. Catalytic performance of cerium iron complex oxides for partial oxidation of methane to synthesis gas

    Institute of Scientific and Technical Information of China (English)

    LI Kongzhai; WANG Hua; WEI Yonggang; LIU Mingchun

    2008-01-01

    The cerium iron complex oxides oxygen carder was prepared by the co-precipitation method. The reactions between methane and lattice oxygen from the complex oxides were investigated in a fixed micro-reactor system. The reduced oxygen carrier could be re-oxidized by air and its initial state could be restored. The characterizations of the oxygen carriers were studied using XRD, O2-TPD, and H2-TPR. The results showed that the bulk lattice oxygen of CeO2-Fe2O3 was found to be suitable for the partial oxidation of methane to synthesis gas. There were two kinds of oxygen species on the oxygen carder: the stronger oxygen species that was responsible for the complete oxidation of methane, and the weaker oxygen species (bulk lattice oxygen) that was responsible for the selective oxidation of methane to CO and H2 at a higher temperature. Then, the lost bulk lattice oxygen could be selectively supplemented by air re-oxidation at an appropriate reaction con-dition. CeFeO3 appeared on the oxygen carrier after 10 successive redox cycles, however, it was not bad for the selectivity of CO and H2.

  12. STUDY ON ORGANIC LIGHT—RARE—EARTH ADSORBENT—CERIUM BIS(OCTYLPHOSPHATE)

    Institute of Scientific and Technical Information of China (English)

    SuZhengquan; FengHuixia

    1996-01-01

    The tetravalent metal salts of monoalkyl phosphates[M(R-OPO3)2] are a new kind of stationary phases of chromatography-homogeneous bonded phases.The studies on preparation,structure and gas chromatographic efficiency of cerium bis (octylphosphate) (COPP) are reported in this paper. By using chemical analysis,infrared spectra,x-ray diffraction analysis ,the strong evidence that COPP has a layered structure of the α-zirconium phosphate type was demonstrated,the repetitive unit is C8H17OPO3CeO3POC8H17 and there is a little bending or interpenetration of the alkyl chains within the layers.The thermogravimetic analysis of the COPP indicated that it has much more thermalstability than silica-based packings.The thermodynamic parameters ΔH and molecular connectivity indexes x′ for the adsorption of several dozen compounds on the COPP have also been determined by gas chromatographic method,and the fine linearity between them was shown.

  13. RM1 Semiempirical Quantum Chemistry: Parameters for Trivalent Lanthanum, Cerium and Praseodymium.

    Directory of Open Access Journals (Sweden)

    José Diogo L Dutra

    Full Text Available The RM1 model for the lanthanides is parameterized for complexes of the trications of lanthanum, cerium, and praseodymium. The semiempirical quantum chemical model core stands for the [Xe]4fn electronic configuration, with n =0,1,2 for La(III, Ce(III, and Pr(III, respectively. In addition, the valence shell is described by three electrons in a set of 5d, 6s, and 6p orbitals. Results indicate that the present model is more accurate than the previous sparkle models, although these are still very good methods provided the ligands only possess oxygen or nitrogen atoms directly coordinated to the lanthanide ion. For all other different types of coordination, the present RM1 model for the lanthanides is much superior and must definitely be used. Overall, the accuracy of the model is of the order of 0.07Å for La(III and Pr(III, and 0.08Å for Ce(III for lanthanide-ligand atom distances which lie mostly around the 2.3Å to 2.6Å interval, implying an error around 3% only.

  14. Toxic Effects of Lanthanum, Cerium, Chromium and Zinc on Potamogeton Malaianus

    Institute of Scientific and Technical Information of China (English)

    Wang Xue; Shi Guoxin; Xu Qinsong; Wang Chuntao

    2005-01-01

    The toxic effects of rare earth elements such as lanthanum, cerium and heavy metal elements such as chromium, zinc on Potamogeton malaianus Miq. were studied. The results show that the contents of chlorophyll and soluble protein increase to a certain degree and then decrease under La3+, Ce3+, Zn2+ stress, while there is a constantly dropping tendency under Cr6+ stress. The four ions have different effects on protective enzyme systems of Potamogeton malaianus. They can induce rises of the activities of catalase (CAT) and peroxides (POD) at lower concentration, however, with the increase of ions concentration, the activities decline. The change of SOD activity is exactly opposite to that of CAT and POD activity. It falls at first and rises later. An increasing tendency of MDA content appears with the increasing concentration. The toxicities of La3+, Zn2+, Ce3+ and Cr6+ become more serious in the order. The lethal concentration of Cr6+ to Potamogeton malaianus ranges from 0.5 to 1 mg·L-1, that of Ce3+ and Zn2+ ranges from 3 to 5 mg·L-1, and that of La3+ ranges from 7 to 10 mg·L-1. The toxic mechanism of La3+ and Ce3+ is similar to that of Cr6+ and Zn2+.

  15. CO responses of sensors based on cerium oxide thick films prepared from clustered spherical nanoparticles.

    Science.gov (United States)

    Izu, Noriya; Matsubara, Ichiro; Itoh, Toshio; Akamatsu, Takafumi; Shin, Woosuck

    2013-03-08

    Various types of CO sensors based on cerium oxide (ceria) have been reported recently. It has also been reported that the response speed of CO sensors fabricated from porous ceria thick films comprising nanoparticles is extremely high. However, the response value of such sensors is not suitably high. In this study, we investigated methods of improving the response values of CO sensors based on ceria and prepared gas sensors from core-shell ceria polymer hybrid nanoparticles. These hybrid nanoparticles have been reported to have a unique structure: The core consists of a cluster of ceria crystallites several nanometers in size. We compared the characteristics of the sensors based on thick films prepared from core-shell nanoparticles with those of sensors based on thick films prepared from conventionally used precipitated nanoparticles. The sensors prepared from the core-shell nanoparticles exhibited a resistance that was ten times greater than that of the sensors prepared from the precipitated nanoparticles. The response values of the gas sensors based on the core-shell nanoparticles also was higher than that of the sensors based on the precipitated nanoparticles. Finally, improvements in sensor response were also noticed after the addition of Au nanoparticles to the thick films used to fabricate the two types of sensors.

  16. Destruction of commercial pesticides by cerium redox couple mediated electrochemical oxidation process in continuous feed mode

    International Nuclear Information System (INIS)

    Mediated electrochemical oxidation was carried out for the destruction of commercial pesticide formulations using cerium(IV) in nitric acid as the mediator electrolyte solution in a bench scale set up. The mediator oxidant was regenerated in situ using an electrochemical cell. The real application of this sustainable process for toxic organic pollutant destruction lies in its ability for long term continuous operation with continuous organic feeding and oxidant regeneration with feed water removal. In this report we present the results of fully integrated MEO system. The task of operating the continuous feed MEO system for a long time was made possible by continuously removing the feed water using an evaporator set up. The rate of Ce(IV) regeneration in the electrochemical cell and the consumption for the pesticide destruction was matched based on carbon content of the pesticides. It was found that under the optimized experimental conditions for Ce(III) oxidation, organic addition and water removal destruction efficiency of ca. 99% was obtained for all pesticides studied. It was observed that the Ce(IV) concentration was maintained nearly the same throughout the experiment. The stable operation for 6 h proved that the process can be used for real applications and for possible scale up for the destruction of larger volumes of toxic organic wastes.

  17. Physical properties of new cerium palladium phosphide with C6Cr23-type structure

    Directory of Open Access Journals (Sweden)

    T. Abe

    2014-01-01

    Full Text Available We have found that a cerium palladium phosphide crystallizes into a C6Cr23-type structure with atomic disorder. Prepared polycrystalline samples show a homogeneity range in the ternary Ce–Pd–P phase diagram. The physical properties of the highest-quality sample of Ce2.4Pd20.7P5.9 were investigated by measuring the magnetization, electrical resistivity and specific heat. No pronounced phase transition was observed down to 0.5 K. The Kondo screening of localized 4f electrons in metallic Ce2.4Pd20.7P5.9 appears to be weaker than that in the isostructural compounds of Ce3Pd20Si6 and Ce3Pd20Ge6. By a comparative study of Ce2.4Pd20.7P5.9 and Ce3Pd20X6 (X = Si, Ge, the competition between the Kondo temperature and ordering temperatures including the quadrupolar ordering temperature is briefly discussed.

  18. Untangling the biological effects of cerium oxide nanoparticles: the role of surface valence states

    Science.gov (United States)

    Pulido-Reyes, Gerardo; Rodea-Palomares, Ismael; Das, Soumen; Sakthivel, Tamil Selvan; Leganes, Francisco; Rosal, Roberto; Seal, Sudipta; Fernández-Piñas, Francisca

    2015-10-01

    Cerium oxide nanoparticles (nanoceria; CNPs) have been found to have both pro-oxidant and anti-oxidant effects on different cell systems or organisms. In order to untangle the mechanisms which underlie the biological activity of nanoceria, we have studied the effect of five different CNPs on a model relevant aquatic microorganism. Neither shape, concentration, synthesis method, surface charge (ζ-potential), nor nominal size had any influence in the observed biological activity. The main driver of toxicity was found to be the percentage of surface content of Ce3+ sites: CNP1 (58%) and CNP5 (40%) were found to be toxic whereas CNP2 (28%), CNP3 (36%) and CNP4 (26%) were found to be non-toxic. The colloidal stability and redox chemistry of the most and least toxic CNPs, CNP1 and CNP2, respectively, were modified by incubation with iron and phosphate buffers. Blocking surface Ce3+ sites of the most toxic CNP, CNP1, with phosphate treatment reverted toxicity and stimulated growth. Colloidal destabilization with Fe treatment only increased toxicity of CNP1. The results of this study are relevant in the understanding of the main drivers of biological activity of nanoceria and to define global descriptors of engineered nanoparticles (ENPs) bioactivity which may be useful in safer-by-design strategies of nanomaterials.

  19. Role of phosphate on stability and catalase mimetic activity of cerium oxide nanoparticles.

    Science.gov (United States)

    Singh, Ragini; Singh, Sanjay

    2015-08-01

    Cerium oxide nanoparticles (CeNPs) have been recently shown to scavenge reactive oxygen and nitrogen species (ROS and RNS) in different experimental model systems. CeNPs (3+) and CeNPs (4+) have been shown to exhibit superoxide dismutase (SOD) and catalase mimetic activity, respectively. Due to their nanoscale dimension, CeNPs are expected to interact with the components of biologically relevant buffers and medium, which could alter their catalytic properties. We have demonstrated earlier that CeNPs (3+) interact with phosphate and lose the SOD activity. However, very little is known about the interaction of CeNPs (4+) with the phosphate and other anions, predominantly present in biological buffers and their effects on the catalase mimetic-activity of these nanoparticles. In this study, we report that catalase mimetic-activity of CeNPs (4+) is resistant to the phosphate anions, pH changes and composition of cell culture media. Given the abundance of phosphate anions in the biological system, it is likely that internalized CeNPs would be influenced by cytoplasmic and nucleoplasmic concentration of phosphate.

  20. Enhanced corrosion resistance of magnesium alloy AM60 by cerium(III) in chloride solution

    Energy Technology Data Exchange (ETDEWEB)

    Heakal, F. El-Taib, E-mail: fakihaheakal@yahoo.com [Chemistry Department, Faculty of Science, Cairo University, Giza 12613 (Egypt); Shehata, O.S. [Physical Chemistry Department, National Research Centre, Dokki, Giza (Egypt); Tantawy, N.S. [Girl' s College of Arts, Science and Education, Ain Shams University, Asma Fahmi Street, Cairo (Egypt)

    2012-03-15

    Highlights: Black-Right-Pointing-Pointer Corrosion rate of AM60 in Cl{sup -} solution decreases with increasing [Ce{sup 3+}] up to 1 mM. Black-Right-Pointing-Pointer Beyond that level the corrosion rate increases and then stabilizes. Black-Right-Pointing-Pointer The spontaneously formed film characterises by increasing resistance with time. Black-Right-Pointing-Pointer The converted film after 10 d immersion exhibits self-healing in plain Cl{sup -} solution. Black-Right-Pointing-Pointer Ce(III) should be present in the corrodent to form a more compact surface coating. - Abstract: Cerium(III) was utilised to enhance the corrosion resistance of AM60 in NaCl solution. Ce{sup 3+} can suppress corrosion deterioration up to 1.0 mM. Beyond that level corrosion rate increases till a steady value. Surface film resistance increases with time evolution until 24 h, then decreases and stabilizes. The converted film after 240 h immersion exhibits self-healing and thickening when re-exposed to plain chloride solution. SEM and EDX confirmed that when Ce is present as additive in solution, more compact coating is formed better than its presence as a post coating on the alloy surface before being immersed in the corrosive environment.

  1. Copper-cerium oxides supported on carbon nanomaterial for preferential oxidation of carbon monoxide

    Institute of Scientific and Technical Information of China (English)

    高美怡; 江楠; 赵宇宏; 徐长进; 苏海全; 曾尚红

    2016-01-01

    The CuxO-CeO2/Fe@CNSs, CuxO-CeO2/MWCNTs-Co and CuxO-CeO2/MWCNTs-Ni catalysts were prepared by the im-pregnation method and characterized by transmission electron microscopy, scanning electron microscopy, X-ray powder diffrac-tion, H2-temperature programmed reduction and N2 adsorption-desorption techniques. It was found that the Fe nanoparticles were encapsulated into the multi-layered carbon nanospheres (CNSs). However, the multi-wall carbon nanotubes (MWCNTS) were generated on the Co/Al2O3 and Ni/Al2O3 precursor. The addition of carbon nanomaterial as supports could improve structural properties and low-temperature activity of the CuO-CeO2 catalyst, and save the used amount of metal catalysts in the temperature range with high selectivity for CO oxidation. The copper-cerium oxides supported on carbon nanomaterial had good resistence to H2O and CO2.

  2. Gold-supported cerium-doped NiOx catalysts for water oxidation

    Science.gov (United States)

    Ng, Jia Wei Desmond; García-Melchor, Max; Bajdich, Michal; Chakthranont, Pongkarn; Kirk, Charlotte; Vojvodic, Aleksandra; Jaramillo, Thomas F.

    2016-05-01

    The development of high-performance catalysts for the oxygen-evolution reaction (OER) is paramount for cost-effective conversion of renewable electricity to fuels and chemicals. Here we report the significant enhancement of the OER activity of electrodeposited NiOx films resulting from the combined effects of using cerium as a dopant and gold as a metal support. This NiCeOx-Au catalyst delivers high OER activity in alkaline media, and is among the most active OER electrocatalysts yet reported. On the basis of experimental observations and theoretical modelling, we ascribe the activity to a combination of electronic, geometric and support effects, where highly active under-coordinated sites at the oxide support interface are modified by the local chemical binding environment and by doping the host Ni oxide with Ce. The NiCeOx-Au catalyst is further demonstrated in a device context by pairing it with a nickel-molybdenum hydrogen evolution catalyst in a water electrolyser, which delivers 50 mA consistently at 1.5 V over 24 h of continuous operation.

  3. Effect of Cerium Doping on Superconducting Properties of YBCO Film Prepared by TFA-MOD Method

    International Nuclear Information System (INIS)

    The effects of Ba and Ce addition has been investigated in YBCO prepared by trifluoroacetate(TFA) metalorganic deposition(MOD) method. Precursor solutions with cation ratios of Y:Ba:Cu:Ce=1:2+x:3:x(x=0, 0.05, 0.1 and 1.5) have been prepared by adding an excess amount of cerium and barium. Coated film was calcined at lower temperature under a moisture-containing oxygen atmosphere. Superconducting YBCO films have been obtained by performing conversion heat treatment at temperature of 780-810 degrees C under a moisture-containing Ar(1,000 ppm oxygen) atmosphere. It has been shown that the critical current(Ic) of YBCO film was degraded by doping of Ba and Ce atoms. But Ic was increased as the amount of doped Ba and Ce content increased from 5% to 15 %. It was observed that there was little increase of a flux pinning force with Ba and Ce addition in YBCO film prepared by TFA-MOD process.

  4. Recent advances of cerium oxide nanoparticles in synthesis, luminescence and biomedical studies:a review

    Institute of Scientific and Technical Information of China (English)

    何立莹; 苏玉民; 蒋兰宏; 石士考

    2015-01-01

    Nanostructured cerium oxide (CeO2) commonly known as nanoceria is a rare earth metal oxide, which plays a technologi-cally important role due to its versatile applications as automobile exhaust catalysts, oxide ion conductors in solid oxide fuel cells, electrode materials for gas sensors, ultraviolet absorbents and glass-polishing materials. However, nanoceria has little or weak lumi-nescence, and therefore its uses in high-performance luminescent devices and biomedical areas are limited. In this review, we present the recent advances of nanoceria in the aspects of synthesis, luminescence and biomedical studies. The CeO2 nanoparticles can be synthesized by solution-based methods including co-precipitation, hydrothermal, microemulsion process, sol-gel techniques, combus-tion reaction and so on. Achieving controlled morphologies and enhanced luminescence efficiency of nanoceria particles are quite es-sential for its potential energy- and environment-related applications. Additionally, a new frontier for nanoceria particles in biomedi-cal research has also been opened, which involves low toxicity, retinopathy, biosensors and cancer therapy aspects. Finally, the sum-mary and outlook on the challenges and perspectives of the nanoceria particles are proposed.

  5. A nanostructured cerium oxide film-based immunosensor for mycotoxin detection

    Science.gov (United States)

    Kaushik, Ajeet; Rathee Solanki, Pratima; Ansari, Anees Ahmad; Ahmad, Sharif; Dhar Malhotra, Bansi

    2009-02-01

    Rabbit-immunoglobulin antibodies (r-IgGs) and bovine serum albumin (BSA) have been immobilized onto sol-gel-derived nanostructured cerium oxide (nanoCeO2) film fabricated onto an indium-tin-oxide (ITO) coated glass plate to detect ochratoxin-A (OTA). Broad reflection planes obtained in x-ray diffraction (XRD) patterns reveal the formation of CeO2 nanostructures. Electrochemical studies reveal that nanoCeO2 particles provide an increased electroactive surface area for loading of r-IgGs with desired orientation, resulting in enhanced electron communication between r-IgGs and electrode. BSA/r-IgGs/nano CeO2/ITO immunoelectrode exhibits improved characteristics such as linear range (0.5-6 ng dl-1), low detection limit (0.25 ng dl-1), fast response time (30 s) and high sensitivity (1.27 µA ng-1 dl-1 cm-2). The high value of the association constant (Ka, 0.9 × 1011 l mol-1) indicates the high affinity of the BSA/r-IgGs/nanoCeO2/ITO immunoelectrode to OTA.

  6. Gold-supported cerium-doped NiOx catalysts for water oxidation

    Science.gov (United States)

    Ng, Jia Wei Desmond; García-Melchor, Max; Bajdich, Michal; Chakthranont, Pongkarn; Kirk, Charlotte; Vojvodic, Aleksandra; Jaramillo, Thomas F.

    2016-05-01

    The development of high-performance catalysts for the oxygen-evolution reaction (OER) is paramount for cost-effective conversion of renewable electricity to fuels and chemicals. Here we report the significant enhancement of the OER activity of electrodeposited NiOx films resulting from the combined effects of using cerium as a dopant and gold as a metal support. This NiCeOx–Au catalyst delivers high OER activity in alkaline media, and is among the most active OER electrocatalysts yet reported. On the basis of experimental observations and theoretical modelling, we ascribe the activity to a combination of electronic, geometric and support effects, where highly active under-coordinated sites at the oxide support interface are modified by the local chemical binding environment and by doping the host Ni oxide with Ce. The NiCeOx–Au catalyst is further demonstrated in a device context by pairing it with a nickel–molybdenum hydrogen evolution catalyst in a water electrolyser, which delivers 50 mA consistently at 1.5 V over 24 h of continuous operation.

  7. Tribological characteristics of monodispersed cerium borate nanospheres in biodegradable rapeseed oil lubricant

    Science.gov (United States)

    Boshui, Chen; Kecheng, Gu; Jianhua, Fang; Jiang, Wu; Jiu, Wang; Nan, Zhang

    2015-10-01

    Stearic acid-capped cerium borate composite nanoparticles, abbreviated as SA/CeBO3, were prepared by hydrothermal method. The morphologies, element compositions, size distributions, crystal and chemical structures, hydrophobic characteristics, of SA/CeBO3 were characterized by scanning electron microscope, energy dispersive X-ray spectrometer, dynamic laser particle size analyzer, X-ray diffraction, and Fourier transform infrared spectrometer, respectively. The friction and wear performances of SA/CeBO3 as a lubricating additive in a rapeseed oil were evaluated on a four-ball tribo-tester. The tribochemical characteristics of the worn surfaces were investigated by X-ray photoelectron spectroscopy. The results showed that the hydrophobic SA/CeBO3 were monodispersed nanospheres with an average diameter of 8 nm, and exhibited excellent dispersing stability in rapeseed oil. Meanwhile, SA/CeBO3 nanospheres were outstanding in enhancing friction-reducing and anti-wear capacities of rapeseed oil. The prominent tribological performances of SA/CeBO3 in rapeseed oil were attributed to the formation of a composite boundary lubrication film mainly composed of lubricous tribochemical species of B2O3, CeO2 and Fe2O3, and the adsorbates of SA/CeBO3 and rapeseed oil, on the tribo-surfaces.

  8. Effects of cerium on growth and physiological characteristics of Anabaena flosaquae

    Institute of Scientific and Technical Information of China (English)

    WANG Yingjun; LI Jia; L(U) Yun; JIN Hangbiao; DENG Shihuai; ZENG Yunmin

    2012-01-01

    In the present study,the effects of cerium (Ce) on the growth and physiological changes were investigated in the cyanobacterium Anabaenaflosaquae (A.flosaquae) during a 17-day period.The results showed that the content of chlorophyll a (chl-a) and activity of antioxidase (e.g.superoxide dismutase,peroxidase,and catalase) increased with Ce3+ concentration in the range of 0.05 to 0.1 mg/L and the growth of A.flosaquae was stimulated.While at around 5 mg/L,the content of malondiadehyde (MDA) increased significantly but the activity of antioxidase reduced,which resulted in the ruin of antioxidant defense system.Compared to the control (Ce3+-free),the population size of live cells declined significantly.Microcystin-LR (MC-LR),the most common and toxic cyanotoxins produced by A.flosaquae,was detected and the highest content of MC-LR was observed in 10 mg/L Ce3+ treatment.These results implied that the aqueous environment might suffer a more negative ecological impact when exposed to relatively low Ce3+ concentrations (<0.1 mg/L).

  9. Press or pulse exposures determine the environmental fate of cerium nanoparticles in stream mesocosms.

    Science.gov (United States)

    Baker, Leanne F; King, Ryan S; Unrine, Jason M; Castellon, Benjamin T; Lowry, Gregory V; Matson, Cole W

    2016-05-01

    Risk-assessment models indicate that stream ecosystems receiving municipal wastewater effluent may have the greatest potential for exposure to manufactured nanoparticles. The authors determined the fate of cerium oxide (CeO2 ) nanoparticles in outdoor stream mesocosms using 1) 1-time pulse addition of CeO2 nanoparticles, representative of accidental release, and 2) continuous, low-level press addition of CeO2 nanoparticles, representative of exposure via wastewater effluent. The pulse addition led to rapid nanoparticle floc formation, which appeared to preferentially deposit on periphyton in low-energy areas downstream from the location of the input, likely as a result of gravitational sedimentation. Floc formation limited the concentration of suspended nanoparticles in stream water to movement. In contrast, press addition of nanoparticles led to higher suspended nanoparticle concentrations (77% of target) in stream water, possibly as a result of stabilization of suspended nanoparticles through interaction with dissolved organic carbon. Smaller nanoparticle aggregates appeared to preferentially adsorb to stream surfaces in turbulent sections, where Ce concentrations were highest in the press, likely a result of stochastic encounter with the surface. Streams receiving wastewater effluent containing nanoparticles may lead to exposure of aquatic organisms over a greater spatial extent than a similar amount of nanoparticles from an accidental release. Exposure models must take into account these mechanisms controlling transport and depositional processes. PMID:26576038

  10. Hierarchical porous carbon toward effective cathode in advanced zinc-cerium redox flow battery

    Institute of Scientific and Technical Information of China (English)

    谢志鹏; 杨斌; 蔡定建; 杨亮

    2014-01-01

    Advanced zinc-cerium redox flow battery (ZCRFB) is a large-scale energy storage system which plays a significant role in the application of new energy sources. The requirement of superior cathode with high acitivity and fast ion diffusion is a hierarchical porous structure, which was synthesized in this work by a method in which both hard template and soft template were used. The structure and the performance of the cathode prepared here were characterized and evaluated by a variety of techniques such as scan-ning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), cyclic voltam-metry (CV), linear sweep voltammetry (LSV), and chronoamperometry (CA). There were mainly three types of pore size within the hierarchical porous carbon:2μm, 80 nm, and 10 nm. The charge capacity of the cell using hierarchical porous carbon (HPC) as posi-tive electrode was obviously larger than that using carbon felt;the former was 665.5 mAh with a coulombic efficiency of 89.0%and an energy efficiency of 79.0%, whereas the latter was 611.1 mAh with a coulombic efficiency of 81.5%and an energy efficiency of 68.6%. In addition, performance of the ZCRFB using HPC as positive electrode showed a good stability over 50 cycles. These results showed that the hierarchical porous carbon was superior over the carbon felt for application in ZCRFB.

  11. China's Rare Earth Supply Chain: Illegal Production, and Response to new Cerium Demand

    Science.gov (United States)

    Nguyen, Ruby Thuy; Imholte, D. Devin

    2016-07-01

    As the demand for personal electronic devices, wind turbines, and electric vehicles increases, the world becomes more dependent on rare earth elements. Given the volatile, Chinese-concentrated supply chain, global attempts have been made to diversify supply of these materials. However, the overall effect of supply diversification on the entire supply chain, including increasing low-value rare earth demand, is not fully understood. This paper is the first attempt to shed some light on China's supply chain from both demand and supply perspectives, taking into account different Chinese policies such as mining quotas, separation quotas, export quotas, and resource taxes. We constructed a simulation model using Powersim Studio that analyzes production (both legal and illegal), production costs, Chinese and rest-of-world demand, and market dynamics. We also simulated new demand of an automotive aluminum-cerium alloy in the US market starting from 2018. Results showed that market share of the illegal sector has grown since 2007-2015, ranging between 22% and 25% of China's rare earth supply, translating into 59-65% illegal heavy rare earths and 14-16% illegal light rare earths. There will be a shortage in certain light and heavy rare earths given three production quota scenarios and constant demand growth rate from 2015 to 2030. The new simulated Ce demand would require supply beyond that produced in China. Finally, we illustrate revenue streams for different ore compositions in China in 2015.

  12. Uniform Cerium-Based Coordination Polymer Microsnheres: Preoaration and Upconversion Emission.

    Science.gov (United States)

    Nie, Zhi-Wen; Zeng, Cheng-Hui; Xie, Gang; Zhong, Sheng-Liang

    2016-04-01

    Homogeneously doped Yb3+ and Er3+ cerium-based coordination polymer (CP) microspheres have been successfully synthesized on a large scale through a simple solvothermal route with 2,5-pyridinedicarboxylic acid (2,5-H2PDC) as the organic linker. CeO2: Yb3+, Er3+ porous microspheres were obtained by annealing the corresponding CP microspheres at 600 °C for 4 h under atmospheric pressure. These as-prepared products were characterized by Powder X-ray diffraction (PXRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), energy-dispersion X-ray (EDX) spectroscopy, Thermogravimetric (TG) and derivative thermogravimetric (DTG) analysis. The room temperature upconversion luminescent spectra of the as-prepared microspheres were carried out by 980 nm NIR light excitation. Interestingly, Yb3+ and Er3+ codoped CP microspheres give a single-band emission centered at 673 nm, while the CeO2: Yb3+, Er3+ microspheres give emission in green and red region, with red being the dominant emission. The emission intensity of the CeO2: Yb3+, Er3+ microspheres were much stronger than that of the Yb3+ and Er3+ codoped CP microspheres. PMID:27451693

  13. Novel cerium doped glass-reinforced hydroxyapatite with antibacterial and osteoconductive properties for bone tissue regeneration.

    Science.gov (United States)

    Morais, D S; Fernandes, S; Gomes, P S; Fernandes, M H; Sampaio, P; Ferraz, M P; Santos, J D; Lopes, M A; Sooraj Hussain, N

    2015-09-01

    The aim of this work was to develop a bioactive bone substitute with an effective antibacterial ability based on a cerium (Ce) doped glass-reinforced hydroxyapatite (GR-HA) composite. Developed composites were physicochemically characterized, using x-ray diffraction (XRD) analysis, SEM, energy dispersive x-ray spectroscopy (EDS), and flexural bending strength (FBS) tests. X-ray photoelectron spectroscopy (XPS) analysis was performed to analyze the oxidation state of Ce in the prepared doped glass. The antimicrobial activity of the composites was evaluated against Staphylococcus aureus, Staphylococcus epidermidis and Pseudomonas aeruginosa; whether the cytocompatibility profile was assayed with human osteoblastic-like cells (Mg-63 cell line). The results revealed that the Ce inclusion in the GR-HA matrix induced the antimicrobial ability of the composite. In addition, Ce-doped materials reported an adequate biological behavior following seeding of osteoblastic populations, by inducing cell adhesion and proliferation. Developed materials were also found to enhance the expression of osteoblastic-related genes. Overall, the developed GR-HA_Ce composite is a prospective candidate to be used within the clinical scenario with a successful performance due to the effective antibacterial properties and capability of enhancing the osteoblastic cell response. PMID:26391473

  14. Cerium Oxide Nanoparticles Decorated Graphene Nanosheets for Selective Detection of Dopamine.

    Science.gov (United States)

    Nayak, Pranati; Santhosh, P N; Ramaprabhu, S

    2015-07-01

    The fabrication of a novel amperometric biosensor based on selective determination of dopamine (DA) using nafion coated cerium oxide nanoparticles (NPs) decorated graphene nanosheets (CeO2-HEG-nafion) as a transducer candidate is reported. Graphene was synthesized by hydrogen exfoliation technique. Decoration of CeO2NPs over graphene nanosheets was done by chemical reduction method. The electrochemical impedance spectroscopy (EIS) study shows the enhanced electron transfer kinetics of the composite compared to HEG modified and bare glassy carbon electrode (GCE). The response of the composite towards dopamine displays a lower oxidation potential of 0.23 V and a high oxidation current. The sensor exhibits linearity from 10 µM to 780 µM with a detection limit of 1 µM. In the presence of nafion, it shows excellent selectivity for coexisting interference species like Ascorbic acid (AA) and Uric acid (UA). The excellent performance of the biosensor can be attributed to large active surface area, enhanced electron transfer kinetics and high catalytic activity of the composite.

  15. Relationship between arterial atheromatous plaque morphology and platelet-associated miR-126 and miR-223 expressions

    Institute of Scientific and Technical Information of China (English)

    Heng-Song Tian; Qing-Guo Zhou; Fang Shao

    2015-01-01

    Objective: To study the expression of miR-126 and miR-223 in platelet of rabbit arterial plaque models, and explore its correlation with plaque morphology. Methods: Rabbit arterial plaque models were established, peripheral blood of models and control animals was collected. Plaque morphologies were divided into type Ⅰ, type Ⅱ and type Ⅲ based on angiography plaque morphology and Ambrose method. Platelet isolation kit was applied to isolate and purify peripheral blood platelets, CD45 immunomagnetic beads were used to remove the residual white blood cells. The miRNAs of platelets was extracted by miRNA Isolation Kit, and expressions of miR-126 and miR-223 of the platelets samples were detected by Real-time PCR. The correlation between plaque morphology and platelet-associated miR-126 and miR-223 expressions were analyzed. Expressions of target gene VCAM-1 and P2Y12 receptors of miR-126 and miR-223 in the atherosclerosis plaque of rabbit model were detected by Western blot. Results: Relative expression levels of miR-126 and miR-223 in the model group were 0.27±0.10 and 0.71±0.14, respectively. Plaque morphology was divided into types Ⅰ, Ⅱ and Ⅲ;and miR-126 and miR-223 expression levels were detected in each type. Expression levels of miR-126 in each type were 0.42±0.07, 0.17±0.11 and 0.22±0.15, respectively; and expression levels of miR-223 in each type are 0.68±0.02, 0.57±0.06 and 0.88±0.10, respectively. Relative to the control group, miR-126 and miR-223 known target genes in VCAM-1 and P2Y12 receptors increased platelets in rabbit atherosclerotic plaque models (P<0.05). Conclusions:Relative to normal control animals, miR-126 and miR-223 platelets were reduced in the rabbit atherosclerotic plaque model group (P<0.05). In the type Ⅱ plaque morphology group, miR-126 was greatly reduced; and there is no significant correlation between miR-223 and plaque morphology.

  16. Heavy nuclei far from stability in the N < 126, Z > 82 region

    Energy Technology Data Exchange (ETDEWEB)

    Back, B.B.; Blumenthal, D.J.; Carpenter, M.P. [and others

    1995-08-01

    There are long-standing calculations suggesting that nuclei in the N < 126, Z > 82 region far from stability exhibit deformation effects. Away from stability an observable permanent quadrupole deformation should be achieved but, as yet, there is no experimental evidence for such an effect. A series of experiments was performed to assess the production of nuclei in this region and to study their structure. These experiments were performed using gamma-ray spectroscopy to investigate the low-lying level schemes and alpha-particle spectroscopy in order to isolate fine structure in the decay. The low-lying level structure of the neutron-deficient isotope {sup 202}Rn was studied, for the first time, using the {sup 181}Ta({sup 27}Al,6n) and {sup 192}Pt({sup 16}O,6n) reactions. Gamma-ray transitions between excited states in {sup 202}Rn were identified by mass tagging the Fragment Mass Analyzer and by observation of coincident X rays. Transitions in {sup 203}Rn were also identified. The level scheme deduced from these data is consistent with the systematics of light radon isotopes below the N = 126 shell closure and with theoretical calculations indicating that the ground-state shape should not be strongly deformed at N = 116.

  17. Proton-neutron structure of low lying collective quadrupole excitations in 126Xe

    International Nuclear Information System (INIS)

    Low spin states of the nucleus 126Xe were studied by means of γ-spectroscopy using the fusion evaporation reaction 123Te(α,n)126Xe performed at the Cologne FN TANDEM accelerator. The γγ coincidence and singles spectra were measured with the OSIRIS-cube spectrometer. Beside the ground and quasi-gamma bands many other low lying states were observed. γγ directional correlations from oriented states (DCO) were analyzed to determine the multipolarities of the γ-transitions. We observed dominant E2-transitions in the quasi-gamma band and from the gamma- to the ground band but also a large M1-fraction in the 6+2→61+ transition. We additionally found a strong M1-decay depopulating the 2+4-state at 2064 keV. The lifetime of this state was measured using the Doppler shift attenuation technique. The experimental data are compared with a calculation using the Proton-Neutron Interacting Boson Model (IBM-2). Good agreement is reached in the vicinity of the O(6)-limit. The observed M1-transition of the 2+4 state is interpreted as due to a fragment of the lowest 2+ mixed-symmetry state predicted by the IBM-2

  18. Microscopic description of quadrupole collectivity in neutron-rich nuclei across the N=126 shell closure

    CERN Document Server

    Rodriguez-Guzman, R; Sharma, M M

    2014-01-01

    The quadrupole collectivity in Nd, Sm, Gd, Dy, Er, Yb, Hf and W nuclei with neutron numbers 122 $\\le$ N $\\le$ 156 is studied, both at the mean field level and beyond, using the Gogny energy density functional. Besides the robustness of the N=126 neutron shell closure, it is shown that the onset of static deformations in those isotopic chains with increasing neutron number leads to an enhanced stability and further extends the corresponding two-neutron driplines far beyond what could be expected from spherical calculations. Independence of the mean field predictions with respect to the particular version of the Gogny energy density functional employed is demonstrated by comparing results based on the D1S and D1M parameter sets. Correlations beyond mean field are taken into account in the framework of the angular momentum projected generator coordinate method calculation. It is shown that N=126 remains a robust neutron magic number when dynamical effects are included. The analysis of the collective wave functio...

  19. Effect of selected method of technical processing of meat on the level of cerium 144 in the meat and bones of chicken

    International Nuclear Information System (INIS)

    Experiments were carried out for elimination of cerium 144 radioisotope from the meat and bones of chicken receiving this radioisotope intravitally. The basic methods of technical processing of meat were applied: soaking, boiling, corning. The meat and bones were subjected also to the action of 1% solutions of organic acids used in food industry (citric, acetic, lactic acid). The bones were treated additionally with 5% solutions of these acids. It was found that corning was the method providing best decontamination in the case of the meat, while boiling was most effective in removing the radioactivity from the bones. Among the organic acids the lactic acid in a 1% solution eliminated cerium 144 most effectively from the meat and 5% citric acid from the bones. The effectiveness of these methods of cerium removal depended on the degree of meat fragmentation - the only exception was corning. (author)

  20. Improving in-vitro biocorrosion resistance of Mg-Zn-Mn-Ca alloy in Hank’s solution through addition of cerium

    Institute of Scientific and Technical Information of China (English)

    张凡; 马爱斌; 宋丹; 江静华; 卢富敏; 张留艳; 杨东辉; 陈建清

    2015-01-01

    Two kinds of Mg-Zn-Mn-Ca alloys with and without cerium were designed and fabricated. In-vitro degradation tests and electrochemical evaluations were carried out to compare their biocorrosion behavior in Hank’s solution at 37 ºC. After adding cerium, the continuous network distributed Ca2Mg6Zn3 phases in Mg-2Zn-0.5Mn-1Ca alloy (Alloy I) were separated due to the emerging non-continuously distributed Mg2Ca phase and Mg12CeZn phase. This change led to corrosion acceleration of Mg ma-trix at the initial stage but also sped up the formation of compact corrosion products for Mg-2Zn-0.5Mn-1Ca-1.5Ce alloy (Alloy II), and therefore enhanced its biocorrosion resistance. Cerium containing Alloy II has the potential to be used as future biomate-rials.