WorldWideScience

Sample records for centrifugal partition chromatography

  1. Deep eutectic solvents in countercurrent and centrifugal partition chromatography.

    Science.gov (United States)

    Roehrer, Simon; Bezold, Franziska; García, Eva Marra; Minceva, Mirjana

    2016-02-19

    Deep eutectic solvents (DESs) were evaluated as solvents in centrifugal partition chromatography, a liquid-liquid chromatography separation technology. To this end, the partition coefficients of ten natural compounds of different hydrophobicity were determined in non-aqueous biphasic systems containing DES. The influence of the composition of DESs and the presence of water in the biphasic system on the partition coefficient were also examined. In addition, several process relevant physical properties of the biphasic system, such as the density and viscosity of the phases, were measured. A mixture of three to four hydrophobic compounds was successfully separated in a centrifugal partition extractor using a heptane/ethanol/DES biphasic system.

  2. Methodology for optimally sized centrifugal partition chromatography columns.

    Science.gov (United States)

    Chollet, Sébastien; Marchal, Luc; Jérémy Meucci; Renault, Jean-Hugues; Legrand, Jack; Foucault, Alain

    2015-04-01

    Centrifugal Partition Chromatography (CPC) is a separation process based on the partitioning of solutes between two partially miscible liquid phases. There is no solid support for the stationary phase. The centrifugal acceleration is responsible for both stationary phase retention and mobile phase dispersion. CPC is thus a process based on liquid-liquid mass transfer. The separation efficiency is mainly influenced by the hydrodynamics of the phases in each cell of the column. Thanks to a visualization system, called "Visual CPC", it was observed that the mobile phase can flow through the stationary phase as a sheet, or a spray. Hydrodynamics, which directly governs the instrument efficiency, is directly affected during scale changes, and non-linear phenomena prevent the successful achievement of mastered geometrical scale changes. In this work, a methodology for CPC column sizing is proposed, based on the characterization of the efficiency of advanced cell shapes, taking into account the hydrodynamics. Knowledge about relationship between stationary phase volume, cell efficiency and separation resolution in CPC allowed calculating the optimum cell number for laboratory and industrial scale CPC application. The methodology is highlighted with results on five different geometries from 25 to 5000 mL, for two applications: the separation of alkylbenzene by partitioning with heptane/methanol/water biphasic system; and the separation of peptides by partitioning with n-butanol/acetic acid/water (4/1/5) biphasic system. With this approach, it is possible to predict the optimal CPC column length leading to highest productivity.

  3. Fast centrifugal partition chromatography as a preparative-scale separation technique for citrus flavones

    Science.gov (United States)

    Fast centrifugal partition chromatography (FCPC) is a preparative-scale separations methodology based on the principles of counter current chromatography. Separations by FCPC are typically achieved with higher recoveries and with lower solvent use compared to conventional column chromatography. HSCP...

  4. Isolation of Methoxyfuranocoumarins From Ammi majus by Centrifugal Partition Chromatography.

    Science.gov (United States)

    Bartnik, Magdalena; Mazurek, Anna Katarzyna

    2016-01-01

    Pure methoxyfuranocoumarins were isolated from Ammi majus L. by use of low-pressure column chromatography (LPCC) followed by centrifugal partition chromatography (CPC). The concentrated petroleum ether extract from fruits of A. majus was fractionated on a silica gel column using a gradient of ethyl acetate in dichloromethane (0-80%, v/v). Coumarin-rich fractions were analyzed by thin-layer chromatography (TLC) and high-performance liquid chromatography with diode array detection (HPLC/DAD). Xanthotoxin (8-MOP) and isopimpinellin (isoP), structurally similar compounds, were isolated in one fraction (FR6). To avoid multistep and long-lasting TLC preparation, optimization of CPC conditions has been performed. In one run, an effective separation of 8-MOP and isoP was achieved. The two-phase solvent system composed of n-hexane-ethyl acetate-methanol-water (10 : 8 : 10 : 9; v/v) in an ascending mode (the aqueous phase was a stationary phase, and the organic phase was a mobile phase), with flow rate 3 mL/min and rotation speed 1,600 r.p.m., was used. The identification and high purities of isolated 8-MOP (98.7%) and isoP (100%) were confirmed by HPLC/DAD assay, when compared with standards. The developed CPC method could be applied to the effective isolation of 8-MOP and isoP from plant extracts. The high purity of obtained compounds makes possible further exploitation of these components in biological studies.

  5. Carnosol purification. Scaling-up centrifugal partition chromatography separations.

    Science.gov (United States)

    Bouju, Elodie; Berthod, Alain; Faure, Karine

    2016-09-30

    This paper illustrates the application of a recently proposed protocol allowing the scale-up prediction on hydrostatic countercurrent chromatography columns (centrifugal partition chromatographs or CPC). A commercial extract of rosemary (Rosmarinus officinalis L.) was used as the starting material containing 0.48% of carnosol, an active pharmaceutical ingredient with great potential. After a rapid method development on a small-scale 35-mL CPC instrument that allowed for the determination of the solvent system and maximum sample concentration and volume, the purification was transferred on two larger instruments using the "free space between peaks" method. The method takes into account the technical limitations of the larger instruments, such as pressure and/or maximum centrifugal field, and allows, by simply running an analytical-sized injection on the large scale rotor, to give an accurate prediction of the maximum sample load and best throughput. The 0.27g of rosemary extract maximum load on a 35-mL CPC was transferred as a 1.9g load on a 254-mL medium size CPC and 9g load on a 812-mL CPC. The maximum process efficiency of 3.1mg of carnosol per hour obtained on the small 35-mL column was transferred on the 254-mL CPC giving 8.3mg/h and, on the larger 812-mL column 49.4mg of carnosol could be obtained per hour. If the scaling-up in CPC instruments is not directly homothetic, it can be highly predictable through a few simple experiments.

  6. Solanidine isolation from Solanum tuberosum by centrifugal partition chromatography.

    Science.gov (United States)

    Attoumbré, Jacques; Giordanengo, Philippe; Baltora-Rosset, Sylvie

    2013-07-01

    The aim of this investigation was the preparative isolation of solanidine (aglycone of the two main potato glycoalkaloids: α-chaconine and α-solanine) from fresh Solanum tuberosum (cv. Pompadour) material by implementing a new preparation scheme using centrifugal partition chromatography (CPC). A setup for obtaining solanidine by hydrolysis of the glycoalkaloids found in the skin and sprouts of S. tuberosum was first developed. Then its isolation was carried out by the development of CPC conditions: the solvent system used for separation was ethyl acetate/butanol/water in the ratio 42.5:7.5:50 v/v/v, 0.6 g of crude extract were separated with a 8 mL/min flow rate of mobile phase while rotating at 2500 rpm. A run yielded 98 mg of solanidine (86.7% recovery from the crude extract) in a one-step separation. The purity of the isolated solanidine was over 98%. Thus, CPC has proven to be the method of choice to get solanidine of very high purity from S. tuberosum biomass in large quantities.

  7. Different Ways to On-Line Hyphenate Centrifugal Partition Chromatography and Mass Spectrometry: Application to Prenylated Xanthones from Garcinia mangostana.

    Science.gov (United States)

    Destandau, Emilie; Michel, Thomas; Toribio, Alix; Elfakir, Claire

    2015-11-01

    Centrifugal partition chromatography is a liquid-liquid separation method well adapted for the fractionation or purification of natural compounds from plant extracts. However, following the preparative isolation, the fractions collected must be analysed by high-performance thin-layer chromatography or high-performance liquid chromatography to evaluate their composition and/or their purity. These additional steps are time-consuming and increase the risk of compound degradation. In order to get an instantaneous analysis of fraction content with structural information on the phytochemicals eluted, it is possible to hyphenate on-line centrifugal partition chromatography with mass spectrometry. Depending on the complexity of the extract, two different kinds of centrifugal partition chromatography-mass spectrometry coupling can be performed: centrifugal partition chromatography-mass spectrometry or centrifugal partition chromatography-high-performance liquid chromatography-mass spectrometry coupling. In the first case, one part of the centrifugal partition chromatography effluent is directly introduced in the mass spectrometry ionisation source to identify the eluted compounds, while in the second case, it is directed to a high-performance liquid chromatography-mass spectrometry system where compounds are first separated thanks to high-performance liquid chromatography and then identified using mass spectrometry.

  8. Extraction of cocoa proanthocyanidins and their fractionation by sequential centrifugal partition chromatography and gel permeation chromatography.

    Science.gov (United States)

    Pedan, Vasilisa; Fischer, Norbert; Rohn, Sascha

    2016-08-01

    Cocoa beans contain secondary metabolites ranging from simple alkaloids to complex polyphenols with most of them believed to possess significant health benefits. The increasing interest in these health effects has prompted the need to develop techniques for their extraction, fractionation, separation, and analysis. This work provides an update on analytical procedures with a focus on establishing a gentle extraction technique. Cocoa beans were finely ground to an average particle size of centrifugal partition chromatography (SCPC) and gel permeation column chromatography using Sephadex LH-20. For SCPC, a two-phase solvent system consisting of ethyl acetate/n-butanol/water (4:1:5, v/v/v) was successfully applied for the separation of theobromine, caffeine, and representatives of the two main phenolic compound classes flavan-3-ols and flavonols. Gel permeation chromatography on Sephadex LH-20 using a stepwise elution sequence with aqueous acetone has been shown for effectively separating individual flavan-3-ols. Separation was obtained for (-)-epicatechin, proanthocyanidin dimer B2, trimer C1, and tetramer cinnamtannin A2. The purity of alkaloids and phenolic compounds was determined by HPLC analysis and their chemical identity was confirmed by mass spectrometry.

  9. Influence of flow patterns on chromatographic efficiency in centrifugal partition chromatography.

    Science.gov (United States)

    Marchal, L; Foucaul, A; Patissier, G; Rosant, J M; Legrand, J

    2000-02-11

    Visualization of flow patterns in centrifugal partition chromatography (CPC) was performed with an asynchronous camera and a stroboscope triggered by the CPC rotor, allowing a channel to be selected and observed regardless of rotational speed. Three main types of flow states were noted as a function of rotational speed and flow-rate: jets stuck along channel walls, broken jets and atomization. Our observations emphasize the importance of Coriolis force on flow shape. Chromatographic efficiency was related to the dispersion of the mobile phase in the stationary phase.

  10. Alternative separation steps for monoclonal antibody purification: combination of centrifugal partitioning chromatography and precipitation.

    Science.gov (United States)

    Oelmeier, Stefan A; Ladd-Effio, Christopher; Hubbuch, Jürgen

    2013-12-01

    Protein drugs continue to grow both in medicinal importance as in scale of their production. This furthers the interest in separation technologies that have the potential to replace chromatographic steps in a protein purification process. Two such unit operations that are employed in large scale in the chemical industry are extraction and precipitation. Their usefulness for the purification of proteins has been demonstrated, but the integration of such unit operations in a way that generate an output stream of high protein concentration and low process related impurities was missing. In this work, we employ centrifugal partitioning chromatography ('CPC') in combination with precipitation of the protein of interest to purify a cell culture supernatant of a monoclonal antibody producing cell line. Centrifugal partitioning chromatography was used as means of multi-step extraction using aqueous two-phase systems and was able to remove up to 88.2% of host cell protein ('HCP'). The following PEG driven precipitation and resolubilization of the protein of interest was use to condition the CPC output stream to suit subsequent chromatographic steps, to increase mAb concentration, remove the phase forming polymer, further improve HCP clearance, and integrate a low pH hold step for viral clearance. The entire process reduced HCP content by 99.4% while recovering 93% of the protein of interest. High throughput screening techniques were extensively employed during the development of the process.

  11. Centrifugal partition chromatography as a tool for preparative purification of pea albumin with enhanced yields.

    Science.gov (United States)

    Bérot, Serge; Le Goff, Elisabeth; Foucault, Alain; Quillien, Laurence

    2007-01-15

    A new procedure including the use of centrifugal partition chromatography (CPC) is proposed to purify PA1b and its isoforms. These pea (Pisum sativum L.) seed proteins are toxic against weevils and can be used as an environment-friendly insecticide. CPC was applied to a whole albumin fraction prepared from pea flour. The butanol:aqueous TFA system used in CPC allowed the separation of PA1b from other albumins and a degree of purification above 95%. Compared to analytical procedures based on methanol extraction, anion exchange and then reversed-phase chromatography (RPC), CPC recovered PA1b in much better yield, which is indispensable for large-scale purification of a biodegradable insecticide.

  12. 5-O-caffeoylshikimic acid from Solanum somalense leaves: advantage of centrifugal partition chromatography over conventional column chromatography.

    Science.gov (United States)

    Chideh, Saïda; Pilard, Serge; Attoumbré, Jacques; Saguez, Robert; Hassan-Abdallah, Alshaimaa; Cailleu, Dominique; Wadouachi, Anne; Baltora-Rosset, Sylvie

    2014-09-01

    Solanum somalense leaves, used in Djibouti for their medicinal properties, were extracted by MeOH. Because of the high polyphenol and flavonoid contents of the extract, respectively, determined at 80.80 ± 2.13 mg gallic acid equivalent/g dry weight and 24.4 ± 1.01 mg quercetin equivalent/g dry weight, the isolation and purification of the main polyphenols were carried out by silica gel column chromatography and centrifugal partition chromatography. Column chromatography led to 11 enriched fractions requiring further purification, while centrifugal partition chromatography allowed the easy recovery of the main compound of the extract. In a solvent system composed of CHCl3/MeOH/H2O (9.5:10:5), 21.8 mg of this compound at 97% purity was obtained leading to a yield of 2.63%. Its structure was established as 5-O-caffeoylshikimic acid by mass spectrometry and NMR spectroscopy. This work shows that S. somalense leaves contain very high level of 5-O-caffeoylshikimic acid (0.74% dry weight), making it a potential source of production of this secondary metabolite that is not commonly found in nature but could be partly responsible of the medicinal properties of S. somalense leaves.

  13. Preparative separation of glycoalkaloids α-solanine and α-chaconine by centrifugal partition chromatography.

    Science.gov (United States)

    Attoumbré, Jacques; Lesur, David; Giordanengo, Philippe; Baltora-Rosset, Sylvie

    2012-11-01

    The main glycoalkaloids of a commercial potato cultivar, α-chaconine and α-solanine, were extracted from sprouts of Solanum tuberosum cv. Pompadour by a mixture of MeOH/H(2)O/CH(3)COOH (400/100/50, v/v/v). In these conditions, 2.8±0.62g of crude extract were obtained from 50g of fresh sprouts and the total glycoalkaloid content was determined by analytical HPLC at 216.5mg/100g. α-Chaconine and α-solanine were separated in a preparative scale using centrifugal partition chromatography (CPC). In a solvent system composed of a mixture of ethyl acetate/butanol/water (15/35/50, v/v/v), α-chaconine (54mg) and α-solanine (15mg) were successfully isolated from the crude extract in one step of purification. The purity of isolated compounds was determined to be higher than 92% by HPLC analysis.

  14. Industrial case study on alkaloids purification by pH-zone refining centrifugal partition chromatography.

    Science.gov (United States)

    Kotland, Alexis; Chollet, Sébastien; Diard, Catherine; Autret, Jean-Marie; Meucci, Jeremy; Renault, Jean-Hugues; Marchal, Luc

    2016-11-25

    The industrial potential of pH-zone refining centrifugal partition chromatography has been evaluated by studying the purification of pharmaceutical ingredients at the pilot scale. For the first time, a scale up methodology based on both column capacity and mass transfer efficiency as invariants was developed. The purification of catharanthine and vindoline from an industrial crude extract of aerial parts of Catharanthus roseus, was used as a case of study. Toluene/CH3CN/water (4/1/5, v/v/v) was selected as biphasic solvent system, triethylamine as retainer in the organic stationary phase and sulphuric acid as displacer in the aqueous mobile phase. The separation intensification was performed on a 36mL CPC column equipped with 832 partition twin-cells. The combined effects of four parameters (displacer and retainer concentrations for intensive parameters, flow rate and rotational speed for extensive parameters) were studied by design of experiment in order to maximize both recoveries and productivities. Then, scale change was done on two larger columns (305mL and 1950mL of capacity) equipped with only 231 and 238 partition cells. For this step, it has been shown that the global mass transfer coefficient k0a (the efficiency of a column design) and the stationary phase retention (the capacity of the column) were relevant and useful scale up invariants. A CPC model based on acid-base equilibriums and interfacial mass transfer in continuously stirred tank reactors in series was used to predict fully separations on larger CPC column at the optimized operating conditions and to guide the CPC user in its scale-up strategy. The experimental validation on pilot CPC column, by injecting up to 150g of Catharanthus roseus crude extract on the 1950mL column highlighted the preservation of the separation quality, the non-linear character of the scale up in centrifugal partition chromatography and that a productivity of about 4kg of processed crude extract per day can be reached

  15. Effect of Coriolis force on counter-current chromatographic separation by centrifugal partition chromatography.

    Science.gov (United States)

    Ikehata, Jun-Ichi; Shinomiya, Kazufusa; Kobayashi, Koji; Ohshima, Hisashi; Kitanaka, Susumu; Ito, Yoichiro

    2004-02-06

    The effect of Coriolis force on the counter-current chromatographic separation was studied using centrifugal partition chromatography (CPC) with four different two-phase solvent systems including n-hexane-acetonitrile (ACN); tert-butyl methyl ether (MtBE)-aqueous 0.1% trifluoroacetic acid (TFA) (1:1); MtBE-ACN-aqueous 0.1% TFA (2:2:3); and 12.5% (w/w) polyethylene glycol (PEG) 1000-12.5% (w/w) dibasic potassium phosphate. Each separation was performed by eluting either the upper phase in the ascending mode or the lower phase in the descending mode, each in clockwise (CW) and counterclockwise column rotation. Better partition efficiencies were attained by the CW rotation in both mobile phases in all the two-phase solvent systems examined. The mathematical analysis also revealed the Coriolis force works favorably under the CW column rotation for both mobile phases. The overall results demonstrated that the Coriolis force produces substantial effects on CPC separation in both organic-aqueous and aqueous-aqueous two-phase systems.

  16. Preparative purification of plasmin activity stimulating phenolic derivatives from Gastrodia elata using centrifugal partition chromatography.

    Science.gov (United States)

    Jeon, Je-Seung; Kim, Jeeyoung; Park, Soyoung; Ryou, Chongsuk; Kim, Chul Young

    2016-06-01

    Gastrodia rhizome, a dried and steamed tuber of Gastrodia elata Blume (Orchidaceae), has been traditionally used in Korea, China and Japan for the treatment of neurological and nervous disorders such as headaches, dizziness, vertigo and convulsive illnesses. The ethyl acetate and water extracts of G. elata stimulated plasmin activity. The active ethyl acetate fraction was subjected to centrifugal partition chromatography (CPC) with a two-phase solvent system, composed of n-hexane-ethyl acetate-methanol-water (3:7:4:6, v/v) followed by semi-preparative HPLC purification to separate active compounds and the water fraction was purified by Diaion HP-20 resin and semi-preparative HPLC. In ethyl acetate extract, 4-hydroxybenzyl alcohol (1), 4-hydroxybenzoic acid (2), 4-hydroxybenzaldehyde (3), 4-ethoxymethylphenol (4), 4,4'-oxybis(methylene)diphenol (5) and 4,4'-methylenediphenol (6) were obtained with high purities. Parishin (7) and parishin B (8) were isolated from water extract. Among isolated compounds, 4-hydroxybenzyl alcohol (1), 4-hydroxybenzaldehyde (3) and 4-ethoxymethylphenol (4) significantly stimulated plasmin activity. Copyright © 2015 John Wiley & Sons, Ltd.

  17. Centrifugal partition chromatography in a biorefinery context: Separation of monosaccharides from hydrolysed sugar beet pulp.

    Science.gov (United States)

    Ward, David P; Cárdenas-Fernández, Max; Hewitson, Peter; Ignatova, Svetlana; Lye, Gary J

    2015-09-11

    A critical step in the bioprocessing of sustainable biomass feedstocks, such as sugar beet pulp (SBP), is the isolation of the component sugars from the hydrolysed polysaccharides. This facilitates their subsequent conversion into higher value chemicals and pharmaceutical intermediates. Separation methodologies such as centrifugal partition chromatography (CPC) offer an alternative to traditional resin-based chromatographic techniques for multicomponent sugar separations. Highly polar two-phase systems containing ethanol and aqueous ammonium sulphate are examined here for the separation of monosaccharides present in hydrolysed SBP pectin: l-rhamnose, l-arabinose, d-galactose and d-galacturonic acid. Dimethyl sulfoxide (DMSO) was selected as an effective phase system modifier improving monosaccharide separation. The best phase system identified was ethanol:DMSO:aqueous ammonium sulphate (300gL(-1)) (0.8:0.1:1.8, v:v:v) which enabled separation of the SBP monosaccharides by CPC (200mL column) in ascending mode (upper phase as mobile phase) with a mobile phase flow rate of 8mLmin(-1). A mixture containing all four monosaccharides (1.08g total sugars) in the proportions found in hydrolysed SBP was separated into three main fractions; a pure l-rhamnose fraction (>90%), a mixed l-arabinose/d-galactose fraction and a pure d-galacturonic acid fraction (>90%). The separation took less than 2h demonstrating that CPC is a promising technique for the separation of these sugars with potential for application within an integrated, whole crop biorefinery.

  18. Intensified Separation of Steviol Glycosides from a Crude Aqueous Extract of Stevia rebaudiana Leaves Using Centrifugal Partition Chromatography.

    Science.gov (United States)

    Hubert, Jane; Borie, Nicolas; Chollet, Sébastien; Perret, Joël; Barbet-Massin, Claire; Berger, Monique; Daydé, Jean; Renault, Jean-Hugues

    2015-11-01

    Aqueous extracts of Stevia rebaudiana leaves have been approved since 2008 by the Joint Expert Committee for Food Additives as sugar substitutes in many food and beverages in Western and Far East Asian countries. The compounds responsible for the natural sweetness of Stevia leaves include a diversity of diterpenoid glycosides derived from a steviol skeleton. These steviol glycosides also exhibit a low calorific value as well as promising therapeutic applications, particularly for the treatment of sugar metabolism disturbances. In this work, centrifugal partition chromatography is proposed as an efficient technical alternative to purify steviol glycosides from crude aqueous extracts of Stevia leaves on a multigram scale. Two different commercial instruments, including an ASCPC250® and a FCPE300® made of columns containing 1890 and 231 twin-cells, respectively, were evaluated and compared. All experiments were performed with a polar biphasic solvent system composed of ethyl acetate, n-butanol, and water in a gradient elution mode. When using the 1890 partition cell centrifugal partition chromatography column of 250 mL, 42 mg of stevioside, 68 mg of dulcoside A, and 172 mg of rebaudioside A, three major constituents of the initial extract were obtained from 1 g of the initial mixture at purities of 81%, 83%, and 99%, respectively. The productivity was further improved by intensifying the procedure on the 231 partition cell centrifugal partition chromatography column of 303 mL with the sample mass loading increased up to 5 g, resulting in the recovery of 1.2 g of stevioside, 100 mg of dulcoside A, and 1.1 g of rebaudioside A at purities of 79%, 62%, and 98%, respectively. The structures of the isolated compounds were validated by HPLC-UV, ESI-MS, (1)H, and (13)C NMR analyses. Altogether, the results demonstrate that the column design (i.e., the partition cell number) is an important aspect to be considered for a larger scale centrifugal partition chromatography

  19. Large scale purification of the SERCA inhibitor thapsigargin from Thapsia garganica L. roots using centrifugal partition chromatography.

    Science.gov (United States)

    Ollivier, Anthony; Grougnet, Raphaël; Cachet, Xavier; Meriane, Djamila; Ardisson, Janick; Boutefnouchet, Sabrina; Deguin, Brigitte

    2013-05-01

    Thapsigargin (Tg) is a selective and irreversible inhibitor of the sarcoplasmic/endoplasmic reticulum calcium ATPase (SERCA)-dependent pump at subnanomolecular concentrations. As such, it has become a powerful tool in the study of Ca(2+) signaling pathway. Purification of Tg from Thapsia species requires repeated chromatographic steps with normal-phase alumina or silica and reverse phase chromatography. We thus developed an innovative procedure coupling high pressure automatized extraction with centrifugal partition chromatography allowing a fast and safe large-scale isolation of highly pure Tg, in two steps from Thapsia garganica L. roots. Comparison of influence of extraction procedures, storage conditions and harvesting areas on Tg content in different Algerian specimens of Thapsia garganica L. roots has been precised by mean of HPLC quantification procedure. Highest Tg content were found in the fresh material of the sample from Setif area.

  20. Separation of active laccases from Pleurotus sapidus culture supernatant using aqueous two-phase systems in centrifugal partition chromatography.

    Science.gov (United States)

    Schwienheer, C; Prinz, A; Zeiner, T; Merz, J

    2015-10-01

    For the production of bio active compounds, e.g., active enzymes or antibodies, a conserved purification process with a minimum loss of active compounds is necessary. In centrifugal partition chromatography (CPC), the separation effect is based on the different distribution of the components to be separated between two immiscible liquid phases. Thereby, one liquid phase is kept stationary in chambers by a centrifugal field and the mobile phase is pumped through via connecting ducts. Aqueous two phase systems (ATPS) are known to provide benign conditions for biochemical products and seem to be promising when used in CPC for purification tasks. However, it is not known if active biochemical compounds can "survive" the conditions in a CPC where strong shear forces can occur due to the two-phasic flow under centrifugal forces. Therefore, this aspect has been faced within this study by the separation of active laccases from a fermentation broth of Pleurotus sapidus. After selecting a suitable ATPS and operating conditions, the activity yield was calculated and the preservation of the active enzymes could be observed. Therefore, CPC could be shown as potentially suitable for the purification of bio-active compounds.

  1. Investigation, comparison and design of chambers used in centrifugal partition chromatography on the basis of flow pattern and separation experiments.

    Science.gov (United States)

    Schwienheer, C; Merz, J; Schembecker, G

    2015-04-17

    In centrifugal partition chromatography (CPC) the separation efficiency is mainly influenced by the hydrodynamic of mobile and stationary phase in the chambers. Thus, the hydrodynamic has to be investigated and understood in order to enhance a CPC separation run. Different chamber geometries have been developed in the past and the influence of several phase systems and CPC operating conditions were investigated for these chambers. However, a direct comparison between the different chamber types has not been performed yet. In order to investigate the direct influence of the chamber design on the hydrodynamic, several chamber designs - partially similar in geometry to commercial available designs - are investigated under standardized conditions in the present study. The results show the influence of geometrical aspects of the chamber design on the hydrodynamic and therewith, on the separation efficiency. As a conclusion of the present study, some ideas for an optimal chamber design for laboratory and industrial purpose are proposed.

  2. Isolation and purification of phenylethanoid glycosides from plant extract of Plantago asiatica by high performance centrifugal partition chromatography

    Institute of Scientific and Technical Information of China (English)

    Li Li; Chun Ming Liu; Zhi Qiang Liu; Jing Wang

    2008-01-01

    Two phenylethanoid glycosides (PhGs) were isolated and purified from the aerial parts of Plantago asiatica for the first time by high performance centrifugal partition chromatography (HPCPC) using ethyl acetate-n-butanol-ethanol-water (0.5:0.5:0.1:1,v/v/v/v).A total of 45.6 mg of compound 1 and 293.8 mg of compound 2 were purified from 1341 mg of the n-butanol extract of P.asiatica.The structures of the two PhGs were tentatively identified as plantamajoside and acteoside or isoacteoside by electrospray ionization multi stage tandem mass spectrometry (ESI-MSn) in the negative ion mode.

  3. Preparative Isolation of Polar Antioxidant Constituents from Abies koreana Using Centrifugal Partition Chromatography Guided by DPPH center dot-HPLC Experiment

    NARCIS (Netherlands)

    Jeon, Je-Seung; Kim, Ji Hoon; Park, Chae Lee; Kim, Chul Young

    2015-01-01

    Preparative separation of antioxidant constituents from the leaves of Abies koreana Wilson (Pinaceae) was performed by centrifugal partition chromatography (CPC) with a two-phase solvent system of ethyl acetate-isopropanol-water (9:1:10, v/v) target-guided by DPPH•-HPLC experiment. In DPPH•-HPLC exp

  4. Preparative separation of sesamin and sesamolin from defatted sesame meal via centrifugal partition chromatography with consecutive sample injection.

    Science.gov (United States)

    Jeon, Je-Seung; Park, Chae Lee; Syed, Ahmed Shah; Kim, Young-Mi; Cho, Il Je; Kim, Chul Young

    2016-02-01

    A preparative separation method using consecutive sample injection centrifugal partition chromatography (CPC) was developed to obtain sesamin and sesamolin from defatted sesame meal extracts. A two-phase solvent system consisting of n-hexane-ethyl acetate-methanol-water (8:2:8:2, v/v) was applied in reversed-phase mode (descending mode). Preliminary experiments with an SCPC-100 (column volume: 100mL) were performed to select the appropriate two-phase solvent system and sample injection times; these parameters were then used with an SCPC-1000 (column volume: 1000mL) in a 10-fold scale-up preparative run. A sample containing 3g of crude extract was consecutively injected four times onto the SCPC-1000, which yielded 328mg of sesamin and 168mg of sesamolin. These compounds were analyzed by high-performance liquid chromatography and determined to have purities of 95.6% and 93.9%, respectively. Sesamin and sesamolin (30μM) increased antioxidant response element (ARE) luciferase activity 2.6-fold and 1.9-fold, respectively.

  5. Fast Centrifugal Partition Chromatography Fractionation of Concentrated Agave (Agave salmiana) Sap to Obtain Saponins with Apoptotic Effect on Colon Cancer Cells.

    Science.gov (United States)

    Santos-Zea, Liliana; Fajardo-Ramírez, Oscar R; Romo-López, Irasema; Gutiérrez-Uribe, Janet A

    2016-03-01

    Separation of potentially bioactive components from foods and plant extracts is one of the main challenges for their study. Centrifugal partition chromatography has been a successful technique for the screening and identification of molecules with bioactive potential, such as steroidal saponins. Agave is a source of steroidal saponins with anticancer potential, though the activity of these compounds in concentrated agave sap has not been yet explored. In this study, fast centrifugal partition chromatography (FCPC) was used coupled with in vitro tests on HT-29 cells as a screening procedure to identify apoptotic saponins from an acetonic extract of concentrated agave sap. The three most bioactive fractions obtained by FCPC at partition coefficients between 0.23 and 0.4 contained steroidal saponins, predominantly magueyoside b. Flow cytometry analysis determined that the fraction rich in kammogenin and manogenin glycosides induced apoptosis, but when gentrogenin and hecogenin glycosides were also found in the fraction, a necrotic effect was observed. In conclusion, this study provides the evidence that steroidal saponins in concentrated agave sap were potential inductors of apoptosis and that it was possible to separate them using fast centrifugal partition chromatography.

  6. Purification of a modified cyclosporine A by co-current centrifugal partition chromatography: process development and intensification.

    Science.gov (United States)

    Amarouche, Nassima; Boudesocque, Leslie; Sayagh, Charlotte; Giraud, Matthieu; McGarrity, John; Butte, Alessandro; Marchal, Luc; Foucault, Alain; Renault, Jean-Hugues

    2013-10-11

    Synthetic hydrophobic non-ionizable peptides are not soluble in most common solvents and are thus difficult to purify by preparative reversed-phase HPLC, normally used for industrial production. The challenge exists to develop alternative purification chromatographic processes using suitable solvents and providing good yields, high purity and sufficient productivity. A 11mer hydrophobic synthetic modified cyclosporine, showing an anti-HIV activity, was successfully purified by centrifugal partition chromatography using the biphasic solvent system heptane/ethyl acetate/acetone/methanol/water (1:2:2:1:2, v/v). A 5% co-current elution - made possible by the liquid nature of the two phases - has been used in order to avoid hydrodynamic instabilities mainly due to the physico-chemical properties of the target peptide. This original solution was developed after the study of the effect of the peptide on the hydrodynamic behavior of the two phases during the separation, and the visualization of the flow patterns using the Visual-CPC device. Critical impurities were efficiently eliminated and the peptide was recovered in high yield and high productivity achieving the specifications requirements.

  7. Bioactivity-guided identification of antimicrobial metabolites in Alnus glutinosa bark and optimization of oregonin purification by Centrifugal Partition Chromatography.

    Science.gov (United States)

    Abedini, Amin; Chollet, Sébastien; Angelis, Apostolis; Borie, Nicolas; Nuzillard, Jean-Marc; Skaltsounis, Alexios-Leandros; Reynaud, Romain; Gangloff, Sophie C; Renault, Jean-Hugues; Hubert, Jane

    2016-09-01

    Barks from conifers and broadleaved trees constitute abundant wastes generated from wood harvesting and logging activities. Extracts of such residues obtained from Alnus trees have been reported as interesting resources with potent antibacterial activities. The present study aims to determine the antimicrobial activity of a crude methanol extract prepared from the bark of Alnus glutinosa against a panel of 22 bacteria and yeasts and to optimize a purification method enabling the high production of the most active substances. Fractionation of the crude extract was performed by Centrifugal Partition Chromatography (CPC) using a three-phase solvent system composed of n-heptane, methyl-ter-butyl ether, acetonitrile and water. The major known compounds contained in the fractions produced by CPC were chemically profiled by (13)C NMR dereplication, resulting in the unambiguous identification of oregonin, hirsutanonol, betulinic acid, and alusenone 1a. The antibacterial evaluation of the fractions by bioautography on Staphylococcus aureus revealed that oregonin, in addition to being the major metabolite of the crude extract (∼32% w/w), was the most active with an antibacterial inhibitory effect comparable to antibiotics. The purification of oregonin was optimized at the laboratory-scale by CPC. A single injection of 3.7g of crude extract resulted in a recovery of 72% (850mg) of the available oregonin at purity higher than 94%.

  8. Selective enrichment in bioactive compound from Kniphofia uvaria by super/subcritical fluid extraction and centrifugal partition chromatography.

    Science.gov (United States)

    Duval, Johanna; Destandau, Emilie; Pecher, Virginie; Poujol, Marion; Tranchant, Jean-François; Lesellier, Eric

    2016-05-20

    Nowadays, a large portion of synthetic products (active cosmetic and therapeutic ingredients) have their origin in natural products. Kniphofia uvaria is a plant from Africa which has proved in the past by in-vivo tests an antioxidant activity due to compounds present in roots. Recently, we have observed anthraquinones in K. uvaria seeds extracts. These derivatives are natural colorants which could have interesting bioactive potential. The aim of this study was to obtain an extract enriched in anthraquinones from K. uvaria seeds which mainly contains glycerides. First, the separation of the seed compounds was studied by using supercritical fluid chromatography (SFC) in the goal to provide a rapid quantification method of these bioactive compounds. A screening of numerous polar stationary phases was achieved for selecting the most suited phase to the separation of the four anthraquinones founded in the seeds. A gradient elution was optimized for improving the separation of the bioactive compounds from the numerous other families of major compounds of the extracts (fatty acids, di- and triglycerides). Besides, a non-selective and green Supercritical Fluid Extraction (SFE) with pure CO2 was applied to seeds followed by a Centrifugal Partition Chromatography (CPC). The CPC system was optimized by using the Arizona phase system, to enrich the extract in anthraquinones. Two systems were selected to isolate the bioactive compounds from the oily extract with varied purity target. The effect of the injection mode for these very viscous samples was also studied. Finally, in order to directly apply a selective process of extraction to the seeds, the super/subcritical fluid extraction was optimized to increase the anthraquinone yield in the final extract, by studying varied modifier compositions and nature, as well as different temperatures and backpressures. Conditions suited to favour an enrichment factor bases on the ratio of anthraquinone and trilycerides extracted are

  9. Phase system selection with fractional factorial design for purification of recombinant cyanovirin-N from a hydroponic culture medium using centrifugal partition chromatography.

    Science.gov (United States)

    Grudzień, Łukasz; Madeira, Luisa; Fisher, Derek; Ma, Julian; Garrard, Ian

    2013-04-12

    Centrifugal partition chromatography (CPC) with an aqueous two-phase system (ATPS) was used to purify recombinant cyanovirin-N (CV-N) from other proteins which were co-secreted into a hydroponic plant medium in a rhizosecretion process. To achieve satisfactory protein concentration, the purification was preceded by ultrafiltration performed on a 5 kDa filter. ATPS, because of their gentle nature, were selected as the phase system for CPC. A systematic phase system selection was applied. This involved studying the effect of seven parameters of ATPS: polymer type, salt type, the polymer and salt concentration, the polymer molecular weight, pH, and presence of two additional salts; NaCl and NaClO4, which all together gave 320 combinations. design of experiment (DoE) software allowed the reduction of this number to 46. Having tested partitioning of cyanovirin-N and impurities in 46 ATPS, the three best potential phase systems generated by the programme were then tested on the CPC. Out of these three, 13/13% PEG4000 sodium phosphate, pH 3.0, proved to be most effective phase system in the purification of cyanovirin-N, judged by ELISA and SDS-PAGE analysis, as it eliminated most of the impurities from the final cyanovirin-N preparation.

  10. Concentration and selective fractionation of an antihypertensive peptide from an alfalfa white proteins hydrolysate by mixed ion-exchange centrifugal partition chromatography.

    Science.gov (United States)

    Boudesocque, Leslie; Kapel, Romain; Paris, Cedric; Dhulster, Pascal; Marc, Ivan; Renault, Jean-Hugues

    2012-09-15

    This article reports a promising use of the mixed ion-exchange centrifugal partition chromatography (MIXCPC) technique in the field of downstream processes. A complex alfalfa white protein concentrate hydrolysate (AWPC hydrolysate) showing anti-hypertensive properties was successfully fractionated by MIXCPC to yield a L-valyl-L-tryptophan (VW) enriched fraction in one run. This dipeptide shows an interesting anti-angiotensin converting enzyme (anti-ACE) activity. An analytical method based on RP-LC/MS-MS was developed to quantify the target VW peptide in both the starting material and the enriched fractions. The best results for the MIXCPC fractionation were obtained by the combined use of the quaternary biphasic solvent system, methyl-tert-butylether/acetonitrile/n-butanol/water (2:1:2:5, v/v) in the descending mode, of the lipophilic di(2-ethylhexyl)phosphoric acid (DEHPA) cation-exchanger with an exchanger (DEHPA)/peptides ratio of 15, and of two displacers: calcium chloride and hydrochloric acid. The complexity of the starting material involved the selectivity optimization by splitting the stationary phase into two sections that differed by their triethylamine concentration. From 1g of AWPC hydrolysate containing 0.26% of VW, 30.7 mg of a VW enriched fraction were recovered with a purity of 10.9%, corresponding to a purification factor of 41 and a recovery of 97%.

  11. Employment of High-Performance Thin-Layer Chromatography for the Quantification of Oleuropein in Olive Leaves and the Selection of a Suitable Solvent System for Its Isolation with Centrifugal Partition Chromatography.

    Science.gov (United States)

    Boka, Vasiliki-Ioanna; Argyropoulou, Aikaterini; Gikas, Evangelos; Angelis, Apostolis; Aligiannis, Nektarios; Skaltsounis, Alexios-Leandros

    2015-11-01

    A high-performance thin-layer chromatographic methodology was developed and validated for the isolation and quantitative determination of oleuropein in two extracts of Olea europaea leaves. OLE_A was a crude acetone extract, while OLE_AA was its defatted residue. Initially, high-performance thin-layer chromatography was employed for the purification process of oleuropein with fast centrifugal partition chromatography, replacing high-performance liquid-chromatography, in the stage of the determination of the distribution coefficient and the retention volume. A densitometric method was developed for the determination of the distribution coefficients, KC = CS/CM. The total concentrations of the target compound in the stationary phase (CS) and in the mobile phase (CM) were calculated by the area measured in the high-performance thin-layer chromatogram. The estimated Kc was also used for the calculation of the retention volume, VR, with a chromatographic retention equation. The obtained data were successfully applied for the purification of oleuropein and the experimental results confirmed the theoretical predictions, indicating that high-performance thin-layer chromatography could be an important counterpart in the phytochemical study of natural products. The isolated oleuropein (purity > 95%) was subsequently used for the estimation of its content in each extract with a simple, sensitive and accurate high-performance thin-layer chromatography method. The best fit calibration curve from 1.0 µg/track to 6.0 µg/track of oleuropein was polynomial and the quantification was achieved by UV detection at λ 240 nm. The method was validated giving rise to an efficient and high-throughput procedure, with the relative standard deviation % of repeatability and intermediate precision not exceeding 4.9% and accuracy between 92% and 98% (recovery rates). Moreover, the method was validated for robustness, limit of quantitation, and limit of detection. The amount of oleuropein for

  12. Dereplication of depsides from the lichen Pseudevernia furfuracea by centrifugal partition chromatography combined to {sup 13}C nuclear magnetic resonance pattern recognition

    Energy Technology Data Exchange (ETDEWEB)

    Oettl, Sarah K. [Institute of Pharmacy/Pharmacognosy, Center for Molecular Biosciences Innsbruck, University of Innsbruck, Innrain 80–82, 6020 Innsbruck (Austria); Hubert, Jane, E-mail: jane.hubert@univ-reims.fr [Institut de Chimie Moléculaire de Reims (UMR CNRS 7312), SFR CAP' sANTE, UFR de Pharmacie, Université de Reims Champagne-Ardenne, BP 1039, 51687 Reims Cedex 2 (France); Nuzillard, Jean-Marc [Institut de Chimie Moléculaire de Reims (UMR CNRS 7312), SFR CAP' sANTE, UFR de Pharmacie, Université de Reims Champagne-Ardenne, BP 1039, 51687 Reims Cedex 2 (France); Stuppner, Hermann [Institute of Pharmacy/Pharmacognosy, Center for Molecular Biosciences Innsbruck, University of Innsbruck, Innrain 80–82, 6020 Innsbruck (Austria); Renault, Jean-Hugues [Institut de Chimie Moléculaire de Reims (UMR CNRS 7312), SFR CAP' sANTE, UFR de Pharmacie, Université de Reims Champagne-Ardenne, BP 1039, 51687 Reims Cedex 2 (France); Rollinger, Judith M. [Institute of Pharmacy/Pharmacognosy, Center for Molecular Biosciences Innsbruck, University of Innsbruck, Innrain 80–82, 6020 Innsbruck (Austria)

    2014-10-10

    Highlights: • The major depsides of a lichen extract were directly identified within mixtures. • The initial extract was rapidly fractionated by CPC in the pH-zone refining mode. • Hierarchical clustering of {sup 13}C NMR signals resulted in the identification of depside molecular skeletons. • {sup 13}C chemical shift clusters were assigned to structures using a {sup 13}C NMR database. • Six depsides were unambiguously identified by this approach. - Abstract: Lichens produce a diversity of secondary metabolites, among them depsides comprised of two or more hydroxybenzoic acid units linked by ester, ether, or C-C-bonds. During classic solid support-based purification processes, depsides are often hydrolyzed and in many cases time, consuming procedures result only in the isolation of decomposition products. In an attempt to avoid extensive purification steps while maintaining metabolite structure integrity, we propose an alternative method to identify the major depsides of a lichen crude extract (Pseudevernia furfuracea var. ceratea (Ach.) D. Hawksw., Parmeliaceae) directly within mixtures. Exploiting the acidic character of depsides and differences in polarity, the extract was fractionated by centrifugal partition chromatography in the pH-zone refining mode resulting in twelve simplified mixtures of depsides. After {sup 13}C nuclear magnetic resonance analysis of the produced fractions, the major molecular structures were directly identified within the fraction series by using a recently developed pattern recognition method, which combines spectral data alignment and hierarchical clustering analysis. The obtained clusters of {sup 13}C chemical shifts were assigned to their corresponding molecular structures with the help of an in-house {sup 13}C NMR chemical shift database, resulting in six unambiguously identified compounds, namely methyl β-orcinolcarboxylate (1), atranorin (2), 5-chloroatranorin (3), olivetol carboxylic acid (4), olivetoric acid (5

  13. Intensified extraction of ionized natural products by ion pair centrifugal partition extraction.

    Science.gov (United States)

    Hamzaoui, Mahmoud; Hubert, Jane; Hadj-Salem, Jamila; Richard, Bernard; Harakat, Dominique; Marchal, Luc; Foucault, Alain; Lavaud, Catherine; Renault, Jean-Hugues

    2011-08-05

    The potential of centrifugal partition extraction (CPE) combined with the ion-pair (IP) extraction mode to simultaneously extract and purify natural ionized saponins from licorice is presented in this work. The design of the instrument, a new laboratory-scale Fast Centrifugal Partition Extractor (FCPE300(®)), has evolved from centrifugal partition chromatography (CPC) columns, but with less cells of larger volume. Some hydrodynamic characteristics of the FCPE300(®) were highlighted by investigating the retention of the stationary phase under different flow rate conditions and for different biphasic solvent systems. A method based on the ion-pair extraction mode was developed to extract glycyrrhizin (GL), a biologically active ionic saponin naturally present in licorice (Glycyrrhiza glabra L., Fabaceae) roots. The extraction of GL was performed at a flow rate of 20 mL/min in the descending mode by using the biphasic solvent system ethyl acetate/n-butanol/water in the proportions 3/2/5 (v/v/v). Trioctylmethylammonium with chloride as a counter-ion (Al336(®)) was used as the anion extractant in the organic stationary phase and iodide, with potassium as counter-ion, was used as the displacer in the aqueous mobile phase. From 20 g of a crude extract of licorice roots, 2.2g of GL were recovered after 70 min, for a total process duration of 90 min. The combination of the centrifugal partition extractor with the ion-pair extraction mode (IP-CPE) offers promising perspectives for industrial applications in the field of natural product isolation or for the fractionation of natural complex mixtures.

  14. In-situ protein determination to monitor contamination in a centrifugal partition chromatograph.

    Science.gov (United States)

    Bouiche, Feriel; Faure, Karine

    2017-02-24

    Centrifugal partition chromatography (CPC) works with biphasic liquid systems including aqueous two-phase systems. Metallic rotors are able to retain an aqueous stationary phase able to purify proteins. But the adhesion of proteins to solid surface may pose a cross-contamination risk during downstream processes. So it is of utmost importance to ensure the cleanliness of the equipment and detect possible protein contamination in a timely manner. Thereby, a direct method that allows the determination of the effective presence of proteins and the extent of contamination in the metallic CPC rotors was developed. This in-situ method is derived from the Amino Density Estimation by Colorimetric Assay (ADECA) which is based on the affinity of a dye, Coomassie Brillant Blue (CBB), with protonated N(+) groups of the proteins. In this paper, the ADECA method was developed dynamically, on a 25 mL stainless-steel rotor with various extents of protein contaminations using bovine serum albumin (BSA) as a fouling model. The eluted CBB dye was quantified and found to respond linearly to BSA contamination up to 70 mg injected. Limits of detection and quantification were recorded as 0.9 mg and 3.1 mg, respectively. While the non-specific interactions between the dye and the rotor cannot currently be neglected, this method allows for in situ determination of proteins contamination and should contribute to the development of CPC as a separation tool in protein purification processes.

  15. Centrifugal partition extraction, a new method for direct metabolites recovery from culture broth: case study of torularhodin recovery from Rhodotorula rubra.

    Science.gov (United States)

    Ungureanu, Camelia; Marchal, Luc; Chirvase, Ana Aurelia; Foucault, Alain

    2013-03-01

    Centrifugal partition extraction (CPE), close to centrifugal partition chromatography, put in contact in a continuous way two immiscible liquid phases. This work presents early experiments on CPE use for solid-liquid-liquid extraction. It was applied to the direct treatment of culture broth for metabolites recovery. Torularhodin is one of the carotenoid pigments produced by the yeast Rhodotorula sp., with a terminal carboxylic group considered nowadays as a powerful antioxidant to be included in food and drugs formulations. Torularhodin was extracted from Rhodotorula rubra ICCF 209 cells by CPE. The recovery of torularhodin reaches 74 μg/g of biomass i.e. 294 μg/L of culture medium. The efficiency of the extraction step increased with the operating flow rate. The extraction yield could reach 91% with a contact time lower than 2 min. A 300 mL apparatus allowed a feed at 90 mL/min. The technique is proposed for extraction or sample preparation before analysis.

  16. Multi-stage mixer-settler planet centrifuge. Preliminary studies on partition of macromolecules with organic-aqueous and aqueous-aqueous two-phase solvent systems.

    Science.gov (United States)

    Ito, Y; Zhang, T Y

    1988-03-11

    A rotary-seal-free planetary centrifuge holds a separation column which consists of multiple partition units (ca. 200) connected in series with transfer tubes. In the cavity of each partition unit the transfer tube extends to form a mixer which vibrates to stir the contents under an oscillating force field generated by the planetary motion of the centrifuge. Consequently, solutes locally introduced at the inlet of the column are subjected to an efficient partition process in each partition unit and separated according to their partition coefficients. The mixer tube equipped with a flexible silicone rubber joint was found to produce excellent results for partition with viscous polymer phase systems. The capability of the method was demonstrated on separation of cytochrome c and lysozyme using a PEG-aqueous dibasic potassium phosphate-aqueous two-phase solvent system.

  17. Using Aspen to Teach Chromatographic Bioprocessing: A Case Study in Weak Partitioning Chromatography for Biotechnology Applications

    Science.gov (United States)

    Evans, Steven T.; Huang, Xinqun; Cramer, Steven M.

    2010-01-01

    The commercial simulator Aspen Chromatography was employed to study and optimize an important new industrial separation process, weak partitioning chromatography. This case study on antibody purification was implemented in a chromatographic separations course. Parametric simulations were performed to investigate the effect of operating parameters…

  18. Recent advances of annular centrifugal extractor for hot test of nuclear waste partitioning process

    Institute of Scientific and Technical Information of China (English)

    HeXiang-Ming; YanYu-Shun; 等

    1998-01-01

    Advances are being made in the design of the annular centrifugal extractor fornuclear fuel reprocessing extraction process studies.The extractors have been built and tested.Twelve stages of this extractor and 50 stages are used toimplement the TRPO process for the cleanup ofcommercial and defense nuclear waste liquids,respectively.Following advances are available:(1) simple way of assembly and disassembly between rotor part and housing part of extractor,ease of manipulator operation;(2)automatic sampling from housing of extractor in hot cell;(3) compact multi-stage housing system;(4) easy interstage link;(5) computer data acquisition and monitoring system of speed.

  19. Novel design for centrifugal counter-current chromatography: VI. Ellipsoid column.

    Science.gov (United States)

    Gu, Dongyu; Yang, Yi; Xin, Xuelei; Aisa, Haji Akber; Ito, Yoichiro

    2015-01-01

    A novel ellipsoid column was designed for centrifugal counter-current chromatography. Performance of the ellipsoid column with a capacity of 3.4 mL was examined with three different solvent systems composed of 1-butanol-acetic acid-water (4:1:5, v/v) (BAW), hexane-ethyl acetate-methanol-0.1 M HCl (1:1:1:1, v/v) (HEMH), and 12.5% (w/w) PEG1000 and 12.5% (w/w) dibasic potassium phosphate in water (PEG-DPP) each with suitable test samples. In dipeptide separation with BAW system, both stationary phase retention (Sf) and peak resolution (Rs) of the ellipsoid column were much higher at 0° column angle (column axis parallel to the centrifugal force) than at 90° column angle (column axis perpendicular to the centrifugal force), where elution with the lower phase at a low flow rate produced the best separation yielding Rs at 2.02 with 27.8% Sf at a flow rate of 0.07 ml/min. In the DNP-amino acid separation with HEMW system, the best results were obtained at a flow rate of 0.05 ml/min with 31.6% Sf yielding high Rs values at 2.16 between DNP-DL-glu and DNP-β-ala peaks and 1.81 between DNP-β-ala and DNP-L-ala peaks. In protein separation with PEG-DPP system, lysozyme and myolobin were resolved at Rs of 1.08 at a flow rate of 0.03 ml/min with 38.9% Sf. Most of those Rs values exceed those obtained from the figure-8 column under similar experimental conditions previously reported.

  20. New 18-l process-scale counter-current chromatography centrifuge.

    Science.gov (United States)

    Sutherland, Ian; Hewitson, Peter; Ignatova, Svetlana

    2009-05-08

    A new Dynamic Extractions Maxi-counter-current chromatography (CCC) centrifuge with a column volume of 18-l has been installed in the Advanced Bioprocessing Centre at Brunel. This instrument has four times the capacity of the 4.6-l Maxi-CCC centrifuge which has been operating robustly for 3 years. Tests using the model sample system benzyl alcohol and p-cresol with a heptane:ethyl acetate:methanol:water (HEMWat) phase system (1.4:0.1:0.5:1.0) show that resolution is almost double with this new high capacity device. Commissioning tests with a mixture of caffeine, K(D)=0.21; ferulic acid, K(D)=0.82; umbelliferone, K(D)=1.2 and vanillin, K(D)=1.49 using a HEMWat phase system of 1:1.5:1:1.5 on the 9-l column show that resolutions equivalent to analytical instruments will be possible using the full 18-l capacity. They also show that predictable scale-up from simple test tube tests is feasible with knowledge of the stationary phase retention for the planned process scale run.

  1. Preparation and application of reversed phase chromatorotor for the isolation of natural products by centrifugal preparative chromatography

    Science.gov (United States)

    A method of preparation of Chromatorotor or plates with a reversed phase (RP) solid silica gel sorbent layer has been developed for preparative centrifugal chromatography. The RP-rotor plates consist of binder free RP solid SiO2 sorbent layers of different thicknesses paked between two supported cir...

  2. Partition coefficients of organic compounds in new imidazolium based ionic liquids using inverse gas chromatography.

    Science.gov (United States)

    Revelli, Anne-Laure; Mutelet, Fabrice; Jaubert, Jean-Noël

    2009-06-05

    Partition coefficients of organic compounds in four ionic liquids: 1-ethanol-3-methylimidazolium tetrafluoroborate, 1-ethanol-3-methylimidazolium hexafluorophosphate, 1,3-dimethylimidazolium dimethylphosphate and 1-ethyl-3-methylimidazolium diethylphosphate were measured using inverse gas chromatography from 303.3 to 332.55K. The influence of gas-liquid and gas-solid interfacial adsorption of different solutes on ionic liquids was also studied. Most of the polar solutes were retained largely by partition while light hydrocarbons were retained predominantly by interfacial adsorption on the ionic liquids studied in this work. The solvation characteristics of the ionic liquids were evaluated using the Abraham solvation parameter model.

  3. Distribution ratio, distribution constant and partition coefficient. Countercurrent chromatography retention of benzoic acid.

    Science.gov (United States)

    Berthod, Alain; Mekaoui, Nazim

    2011-09-09

    There is some confusion in chromatography between terms such as solute distribution ratio, distribution constant and partition coefficient. These terms are very precisely defined in the field of liquid-liquid systems and liquid-liquid extraction as well as in the field of chromatography with sometimes conflicting definitions. Countercurrent chromatography (CCC) is a chromatographic technique in which the stationary phase is a support-free liquid. Since the mobile phase is also liquid, biphasic liquid systems are used. This work focuses on the exact meaning of the terms since there are consequences on experimental results. The retention volumes of solutes in CCC are linearly related to their distribution ratios. The partition coefficient that should be termed (IUPAC recommendation) distribution constant is linked to a single definite species. Using benzoic acid that can dimerize in heptane and ionize in aqueous phase and an 18 mL hydrodynamic CCC column, the role and relationships between parameters and the consequences on experimental peak position and shape are discussed. If the heptane/water distribution constant (marginally accepted to be called partition coefficient) of benzoic acid is 0.2 at 20 °C and can be tabulated in books, its CCC measured distribution ratio or distribution coefficient can change between zero (basic aqueous mobile phase) and more than 25 (acidic aqueous mobile phase and elevated concentration). Benzoic acid distribution ratio and partition coefficient coincide only when both dimerization and ionization are quenched, i.e. at very low concentration and pH 2. It is possible to quench dimerization adding butanol in the heptane/water system. However, butanol additions also affect the partition coefficient of benzoic acid greatly by increasing it.

  4. Fractionation of secondary metabolites of orange (Citrus sinensis L.) leaves by fast centrifugal partition chromatography

    Science.gov (United States)

    Conventional HPLC provides ready detection of the major phenolic compounds in methanol extracts of orange leaves, yet conventional HPLC also shows the presence of many more compounds, to an extent where extensive peak overlap prevents distinct peak detection and reliable quantitation. A more complet...

  5. Fractionation of the secondary metabolites of orange (Citrus sinensis L.) leaves by fast centrifugal partition chromatography

    Science.gov (United States)

    There is interest in the detection of changes in secondary metabolites in orange leaves in response to citrus greening disease. Conventional HPLC analysis readily provides detection of major phenolic compounds, but further, more detailed chromatographic analyses show many more compounds, to an exten...

  6. Development of a modular virus clearance package for anion exchange chromatography operated in weak partitioning mode.

    Science.gov (United States)

    Iskra, Timothy; Sacramo, Ashley; Gallo, Chris; Godavarti, Ranga; Chen, Shuang; Lute, Scott; Brorson, Kurt

    2015-01-01

    Anion exchange chromatography (AEX) operated under weak partitioning mode has been proven to be a powerful polishing step as well as a robust viral clearance step in Pfizer's monoclonal antibody (mAb) platform purification process. A multivariate design of experiment (DoE) study was conducted to understand the impact of operating parameters and feedstream impurity levels on viral clearance by weak partitioning mode AEX. Bacteriophage was used initially as a surrogate for neutral and acidic isoelectric point mammalian viruses (e.g., retrovirus and parvovirus). Five different mAbs were used in the evaluation of process parameters such as load challenge (both product and impurities), load pH, load conductivity, and contact time (bed height and flow-rate). The operating ranges obtained from phage clearance studies and Pfizer's historical data were used to define an appropriate operating range for a subsequent clearance study with model retrovirus and parvovirus. Both phage and virus clearance evaluations included feedstreams containing different levels of impurities such as high molecular mass species (HMMS), host cell proteins (HCPs), and host cell DNA. For all the conditions tested, over 5 log10 of clearance for both retrovirus and parvovirus was achieved. The results demonstrated that weak partitioning mode AEX chromatography is a robust step for viral clearance and has the potential to be included as part of the modular viral clearance approach.

  7. Centrifugal partition extraction in the pH-zone-refining displacement mode: an efficient strategy for the screening and isolation of biologically active phenolic compounds.

    Science.gov (United States)

    Hamzaoui, Mahmoud; Renault, Jean-Hugues; Reynaud, Romain; Hubert, Jane

    2013-10-15

    Centrifugal partition extraction (CPE) was developed for the first time in the pH-zone-refining mode to fractionate a crude bark extract of the African tree Anogeissus leiocarpus Guill. & Perr. (Combretaceae). The fractionation process was performed at a flow rate of 20mL/min using a biphasic solvent system composed of methyl tert-butyl ether/acetonitrile/water (4:1:5, v/v/v) in the ascending mode. Sodium hydroxide (40mM) and trifluoroacetic acid (30mM) were used as retainer and displacer agents, respectively. In a single run of 67min, 3g of the initial crude extract were successfully separated into fractions selectively enriched in ionizable triterpenes, ellagic acid derivatives and flavonoids. The antioxidant potential of the initial crude extract, isolated compounds and fraction pools was also evaluated by using the 2,2-diphenyl-1-picrylhydrazyl (DPPH) stable free radical scavenging assay, providing an interesting view about the effect of the degree of substitution of ellagic acid derivatives on their radical scavenging activity. This study will demonstrate that centrifugal partition extraction used in the pH-zone-refining mode can be proposed as an efficient strategy for the rapid screening of natural phenolic compounds.

  8. High-speed ion-pair partition chromatography in pharmaceutical analysis.

    Science.gov (United States)

    Santi, W; Huen, J M; Frei, R W

    1975-12-24

    Ion-pair chromatography offers attractive possibilities in pharmaceutical analysis. The specificity of the separation systems can be varied over a wide range by appropriate selection of the stationary phase. The choice of a suitable counter-ion can also drastically improve the detection limit, permitting the determination of drug substances in low dosage and possibly of by-products or breakdown products. Ion-pair chromatography of tropane and ergot alkaloids has been investigated using picrate as counter-ion. Alumina, Kieselguhr and various grades of silica gel have been tested as supports. Partition properties studied in a batch procedure have been compared with the actual chromatographic conditions. Columns (10 cm) filled with silical gel (particle size, 5 mum; pore size, 1000 A) show the best performance in the separation of hyoscyamine, scopolamine and ergotamine as picrate ion-pairs. Close control of pH and temperature is essential for reproducible separations. Improvements in detection limits between 100 and 300 times have been observed with these systems. Ion-pair extractions of these alkaloids from dosage forms can be used for sample preparation prior to injection on the the column. This provides an added degree of selectivity and sensitivity.

  9. An Integrated Theory of Adsorption and Partition Mechanism and Eash Contribution to Solute Retention in Reversed Phase Liquid Chromatography

    Institute of Scientific and Technical Information of China (English)

    耿信笃; 弗莱德依瑞格涅尔

    2003-01-01

    With the combination of the the stoichiometric displacement model for retention (SDM-R) in reversed phase liquid chromatography (RPLC) and the stoichiometric displacement model for adsorption (SDM-A) in physical chemistry,the total number of moles of the re-solvated methanol of stationary phase side.nr,and that of solute side in the mobile phase,q,corresponding the one mole of the desorbing solute,were separately determined and referred as the characterization parameters of the contributions of the adsorption mechanism and partition mechanism to the solute retention,respectively.A chromatographic system of insulin,using mobile phase consisting of the pseudo-homologue of alcohols(methanol,ethanol and 2-propanol)-water and trifluoroacetic acid was employed.The maximum number of the methanol layers on the stationary phase surface was found to be 10.6,only 3 of which being valid in usual RPLC,traditionally referred as a volume process in partition mechanism.However,it still follows the SDM-R.Both of q and nr of insulin were found not to be zero,indicating that the retention mechanism of insulin is a mixed mode of partition mechanism and adsorption mechanism.When methanol is used as the organic modifier,the ratio of q/nr was 1.13,indicating the contribution to insulin retention due to partition mechanism being a bit greater than that due to adsorption mechanism.A linear relationship between q,or nr and the carbon number of the pseudo-homologue in the mobile phase was also found.As a methodology for investigating the retention mechanism retention and behavior of biopolymers.a homologue of organic solvents as the organic modifier in mobile phase has also been explored.

  10. ORGANIC-HIGH IONIC STRENGTH AQUEOUS SOLVENT SYSTEMS FOR SPIRAL COUNTER-CURRENT CHROMATOGRAPHY: GRAPHIC OPTIMIZATION OF PARTITION COEFFICIENT.

    Science.gov (United States)

    Zeng, Yun; Liu, Gang; Ma, Ying; Chen, Xiaoyuan; Ito, Yoichiro

    2013-01-10

    A new series of organic-high ionic strength aqueous two-phase solvents systems was designed for separation of highly polar compounds by spiral high-speed counter-current chromatography. A total of 21 solvent systems composed of 1-butanol-ethanol-saturated ammonium sulfate-water at various volume ratios are arranged according to an increasing order of polarity. Selection of the two-phase solvent system for a single compound or a multiple sample mixture can be achieved by two steps of partition coefficient measurements using a graphic method. The capability of the method is demonstrated by optimization of partition coefficient for seven highly polar samples including tartrazine (K=0.77), tryptophan (K=1.00), methyl green (K= 0.93), tyrosine (0.81), metanephrine (K=0.89), tyramine (K=0.98), and normetanephrine (K=0.96). Three sulfonic acid components in D&C Green No. 8 were successfully separated by HSCCC using the graphic selection of the two-phase solvent system.

  11. [Determination of partition coefficient of dissolved gases in transformer oil using phase ratio variation method and static headspace gas chromatography].

    Science.gov (United States)

    Zhao, Jinghong; Wang, Hailong; Liu, Wenmin; Zhou, Yansheng; Guan, Yafeng

    2004-05-01

    The partition coefficients of dissolved gases in transformer oil were determined using a phase ratio variation method and static headspace gas chromatography (GC). A pressure balancing and gas volume-metering device was connected to the vent of a sample loop on a six-port injection valve of the GC. The gas phase sample from the headspace vial of 25 mL was transferred to an 80 microL sample-loop through a fused silica capillary of 0.53 mm i.d., and then separated and determined quantitatively by GC. A 2 m x 1 mm i.d. GDX502 micro-packed column was used for the separation. Five different gas-liquid volume ratios in the headspace vials were measured at different equilibrium concentrations. The partition coefficients of hydrocarbon gases including methane, acetylene, ethylene, ethane and propane dissolved in transformer oil were determined by using linear regression analysis at 20 degrees C and 50 degrees C separately. The errors between the real values and regression values from experimental data were less than 4.14% except methane. Fundamental data for on-line measurement of dissolved gases in transformer oil are provided by GC.

  12. Investigation of Symphytum cordatum alkaloids by liquid-liquid partitioning, thin-layer chromatography and liquid chromatography-ion-trap mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Mroczek, Tomasz [Department of Pharmacognosy with Medicinal Plants Laboratory, Medical University, 1 Chodzki St., 20-093 Lublin (Poland)]. E-mail: tmroczek@pharmacognosy.org; Ndjoko-Ioset, Karine [Laboratoire de Pharmacognosie et Phytochimie, Ecole de Pharmacie Geneve-Lausanne, Universite de Geneve, Quai Ernest-Ansermet 30, CH-1211 Geneva 4 (Switzerland); Glowniak, Kazimierz [Department of Pharmacognosy with Medicinal Plants Laboratory, Medical University, 1 Chodzki St., 20-093 Lublin (Poland); Mietkiewicz-Capala, Agnieszka [Department of Pharmacognosy with Medicinal Plants Laboratory, Medical University, 1 Chodzki St., 20-093 Lublin (Poland); Hostettmann, Kurt [Laboratoire de Pharmacognosie et Phytochimie, Ecole de Pharmacie Geneve-Lausanne, Universite de Geneve, Quai Ernest-Ansermet 30, CH-1211 Geneva 4 (Switzerland)

    2006-05-04

    From the alkalised crude extract of Symphytum cordatum (L.) W.K. roots, pyrrolizidine alkaloids (PAs) were extracted as free tertiary bases and polar N-oxides in a merely one-step liquid-liquid partitioning (LLP) in separation funnel and subsequently pre-fractionated by preparative multiple-development (MD) thin-layer chromatography (TLC) on silica gel plates. In this way three alkaloid fractions of different polarities and retention on silica gel plates were obtained as: the most polar N-oxides of the highest retention, the tertiary bases of medium retention, and diesterified N-oxides of the lowest retention. The former fraction was reduced into free bases by sodium hydrosulfite and purified by LLP on Extrelut-NT3 cartridge. It was further analysed together with the two other fractions by high-performance liquid chromatography (HPLC)-ion-trap mass spectrometry with atmospheric pressure chemical ionization (APCI) interface on XTerra C{sub 18} column using a gradient elution. Based on MS {sup n} spectra, 18 various alkaloids have been tentatively determined for the first time in this plant as the following types of structure: echimidine-N-oxide (three diasteroisomers), 7-sarracinyl-9-viridiflorylretronecine (two diasteroisomers), echimidine (two diasteroisomers), lycopsamine (two diasteroisomers), dihydroechinatine-N-oxide, dihydroheliospathuline-N-oxide, lycopsamine-N-oxide (three diasteroisomers), 7-acetyllycopsamine-N-oxide, symphytine-N-oxide (two diasteroisomers) and 2'',3''-epoxyechiumine-N-oxide.

  13. Background vapor from six ionic liquids and the partition coefficients and limits of detection for 10 different analytes in those ionic liquids measured using headspace gas chromatography.

    Science.gov (United States)

    Von Wald, Grant; Albers, David; Cortes, Hernan; McCabe, Terry

    2008-08-01

    The concentration and identity of the compounds detected in the vapor above six ionic liquids by headspace gas chromatography (HS-GC) at 100 degrees C are reported. In addition, the partition coefficients for 10 different compounds in these ionic liquids and limits of detection were measured. These results provide quantitative guidance for the application of ionic liquids for HS-GC.

  14. CENTRIFUGE APPARATUS

    Science.gov (United States)

    Skarstrom, C.; Urey, H.C.; Cohen, K.

    1960-08-01

    A high-speed centrifuge for the separation of gaseous isotopes is designed comprising a centrifugal pump mounted on the outlet of a centrifuge bowl and arranged to pump the heavy and light fractions out of the centrifuge bowl in two separate streams.

  15. Determination of Five Organic Acids in Radix Isatidis by Column Partition Chromatography and Capillary Zone Electrophoresis

    Institute of Scientific and Technical Information of China (English)

    CHAIYi-fen; JISong-gang; ZHANGGuo-qing; LIUChang-hai

    2003-01-01

    Aim To determine five organic acids in Radix lsatidis. Method The extraction method and the column partition chromatographic conditiom were studied. Then a capillary zone dectrophorefic method was set up for the determina-tion. Results The linear ranges of quinazolinone acid, n-anthranilic acid, benzoic acid, salicylic acid, and syringic acid were 5.52 - 92.0μg·mL-1 , 5.12 - 102μg·mL-1 , 2.28 - 84.4μg·mL-1, 4.78 - 159 μg·mL-1, and 1.74- 87.0μg·mL-1 respectively. Conclusion The established method is accurate and simple.

  16. Chromatography.

    Science.gov (United States)

    Brantley, L. Reed, Sr.; Demanche, Edna L.; Klemm, E. Barbara; Kyselka, Will; Phillips, Edwin A.; Pottenger, Francis M.; Yamamoto, Karen N.; Young, Donald B.

    This booklet presents some activities on chromatography. Directions for preparing leaf pigment extracts using alcohol are given, and paper chromatography and thin-layer chromatography are described as modifications of the basic principles of chromatography. (KHR)

  17. CENTRIFUGAL SEPARATORS

    Science.gov (United States)

    Skarstrom, C.

    1959-03-10

    A centrifugal separator is described for separating gaseous mixtures where the temperature gradients both longitudinally and radially of the centrifuge may be controlled effectively to produce a maximum separation of the process gases flowing through. Tbe invention provides for the balancing of increases and decreases in temperature in various zones of the centrifuge chamber as the result of compression and expansions respectively, of process gases and may be employed effectively both to neutralize harmful temperature gradients and to utilize beneficial temperaturc gradients within the centrifuge.

  18. Centrifugal pumps

    CERN Document Server

    Anderson, HH

    1981-01-01

    Centrifugal Pumps describes the whole range of the centrifugal pump (mixed flow and axial flow pumps are dealt with more briefly), with emphasis on the development of the boiler feed pump. Organized into 46 chapters, this book discusses the general hydrodynamic principles, performance, dimensions, type number, flow, and efficiency of centrifugal pumps. This text also explains the pumps performance; entry conditions and cavitation; speed and dimensions for a given duty; and losses. Some chapters further describe centrifugal pump mechanical design, installation, monitoring, and maintenance. The

  19. Correlation and prediction of partition coefficient using nonrandom two-liquid segment activity coefficient model for solvent system selection in counter-current chromatography separation.

    Science.gov (United States)

    Ren, Da-Bing; Yang, Zhao-Hui; Liang, Yi-Zeng; Ding, Qiong; Chen, Chen; Ouyang, Mei-Lan

    2013-08-02

    Selection of a suitable solvent system is the first and foremost step for a successful counter-current chromatography (CCC) separation. In this paper, a thermodynamic model, nonrandom two-liquid segment activity coefficient model (NRTL-SAC) which uses four types of conceptual segments to describe the effective surface interactions for each solvent and solute molecule, was employed to correlate and predict the partition coefficients (K) of a given compound in a specific solvent system. Then a suitable solvent system was selected according to the predicted partition coefficients. Three solvent system families, heptane/methanol/water, heptane/ethyl acetate/methanol/water (Arizona) and hexane/ethyl acetate/methanol/water, and several solutes were selected to investigate the effectiveness of the NRTL-SAC model for predicting the partition coefficients. Comparison between experimental results and predicted results showed that the NRTL-SAC model is of potential for estimating the K value of a given compound. Also a practical separation case on magnolol and honokiol suggests the NRTL-SAC model is effective, reliable and practical for the purpose of predicting partition coefficients and selecting a suitable solvent system for CCC separation.

  20. Determination of octanol-water partition coefficients of polar polycyclic aromatic compounds (N-PAC) by high performance liquid chromatography

    DEFF Research Database (Denmark)

    Helweg, C.; Nielsen, T.; Hansen, P.E.

    1997-01-01

    Prediction of 1-octanol water partition coefficients for a range of polar N-PAC from HPLC capacity coefficients has been investigated. Two commercially available columns, an ODS column and a Diol column were tested with water-methanol eluents. The best prediction of log K-ow for N-PAC was achieve...

  1. Analysis of selected designer benzodiazepines by UHPLC with high-resolution time-of-flight mass spectrometry and the estimation of their partition coefficients by micellar electrokinetic chromatography.

    Science.gov (United States)

    Tomková, Jana; Švidrnoch, Martin; Maier, Vítězslav; Ondra, Peter

    2017-03-07

    A new ultra high performance liquid chromatography with electrospray ionization time-of-flight mass spectrometry method for the selective and sensitive separation, identification and determination of selected designer benzodiazepines (namely, pyrazolam, phenazepam, etizolam, flubromazepam, diclazepam, deschloroetizolam, bentazepam, nimetazepam and flubromazolam) in human serum was developed. The separation of the studied designer benzodiazepines was achieved on C18 chromatographic column using gradient elution within 6 min without any significant matrix interferences. Liquid-liquid extraction with butyl acetate was applied for serum samples clean-up and preconcentration of studied designer benzodiazepines. The method was validated in terms of linearity, limit of detection, limit of quantification, matrix effects, specificity, precision, accuracy, recovery and sample stability. The limit of detection values were in range 0.10-0.15 ng/mL. The method was applied on spiked serum sample to demonstrate its applicability for systematic toxicology analysis. Furthermore, a capillary chromatographic method with micellar electrokinetic chromatography was used for the estimation of partition coefficients of studied designer benzodiazepines as important parameters to evaluate their pharmacological and toxicological properties. This article is protected by copyright. All rights reserved.

  2. Neuere Chromatographie

    Science.gov (United States)

    Hostettmann, K.

    1983-04-01

    Besides high-performance liquid chromatography (HPLC) which is now a well-established and currently used technique, several emerging methods for the isolation and separation of natural products are receiving considerable attention. Centrifugal thin-layer chromatography is a very rapid technique, but limited in resolution. Of special interest are the recently developed support-free liquid-liquid chromatography methods such as droplet counter-current chromatography (DCCC) and rotation locular counter-current chromatography (RLCC). This latter method was applied to the separation of the enantiomers of (±)-norephedrine.

  3. [Determination of six main components in compound theophylline tablet by convolution curve method after prior separation by column partition chromatography

    Science.gov (United States)

    Zhang, S. Y.; Wang, G. F.; Wu, Y. T.; Baldwin, K. M. (Principal Investigator)

    1993-01-01

    On a partition chromatographic column in which the support is Kieselguhr and the stationary phase is sulfuric acid solution (2 mol/L), three components of compound theophylline tablet were simultaneously eluted by chloroform and three other components were simultaneously eluted by ammonia-saturated chloroform. The two mixtures were determined by computer-aided convolution curve method separately. The corresponding average recovery and relative standard deviation of the six components were as follows: 101.6, 1.46% for caffeine; 99.7, 0.10% for phenacetin; 100.9, 1.31% for phenobarbitone; 100.2, 0.81% for theophylline; 99.9, 0.81% for theobromine and 100.8, 0.48% for aminopyrine.

  4. Centrifugal pyrocontactor

    Science.gov (United States)

    Chow, Lorac S.; Leonard, Ralph A.

    1993-01-01

    A method for mixing and separating immiscible liquid salts and liquid metals in a centrifugal contractor. The method includes introducing the liquids into an annular mixing zone and intensely mixing the liquids using vertical vanes attached to a rotor cooperating with vertical baffles, a horizontal baffle, and bottom vanes attached to the contactor housing. The liquids enter the contactor in the range of 700-800 degrees Celsius. The liquids are separated in the rotor into a dense phase and a light phase which are discharged from the contactor.

  5. Partition chromatography separation using trilaurylamine adsorbed on a solid support. Behaviour of the uranyl ion; Separations par chromatographie de partage au moyen de trilaurylamine adsorbee sur support solide comportement de l'ion uranyle

    Energy Technology Data Exchange (ETDEWEB)

    Petit-Bromet, M. [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1968-07-01

    The extractive phase is made up of a TLA solution in cyclohexanol adsorbed on a solid poly-trifluorochloroethylene support (sold commercially as voltalef or KEL-F). The mixture obtained is homogeneous and can be used for partition chromatography. For a solution of hydrochloric acid stronger than 1 M, the amine is quantitatively in the form of the chlorohydrate. The partition curve for U(VI) between the 2 N hydrochloric acid aqueous phase and the organic TLA phase has two steps which can be explained by assuming that two complexes exist in the organic phase. The equilibrium constants for extraction have been determined. The homogeneity of the voltalef-amine mixture has made it possible to build up a column with reproducible characteristics. Under the operational conditions adopted, the height of the equivalent theoretical plate is about 3 mm. A plot of all the curves giving the variations in the partition function of U(VI), Fe(III), Cu(II), Sr(II) and Cs(I) as a function of the hydrochloric acid concentration makes it possible to predict the conditions under which these elements may be separated. [French] La phase extractive est constituee d'une solution de TLA dans le cyclohexanol adsorbe sur un support solide de polytrifluorochloroethylene (commercialise sous le nom de voltalef ou KEL-F). Le melange obtenu est homogene et peut etre utilise en chromatographie de partage. Pour une concentration d'acide chlorhydrique en solution superieure a 1 M, l'amine est quantitativement sous forme de chlorhydrate. La courbe de partage de U(VI) entre la phase aqueuse d'acide chlorhydrique 2 N et la phase organique de TLA presente deux paliers que l'on peut interpreter en admettant l'existence de deux complexes en phase organique. Les constantes des equilibres d'extraction ont ete determinees. L'homogeneite du melange voltalef-amine a permis de constituer une colonne.dont les caracteristiques sont reproductibles. Dans les conditions de

  6. Centrifugal pumps

    CERN Document Server

    Gülich, Johann Friedrich

    2014-01-01

    This book gives an unparalleled, up-to-date, in-depth treatment of all kinds of flow phenomena encountered in centrifugal pumps including the complex interactions of fluid flow with vibrations and wear of materials. The scope includes all aspects of hydraulic design, 3D-flow phenomena and partload operation, cavitation, numerical flow calculations, hydraulic forces, pressure pulsations, noise, pump vibrations (notably bearing housing vibration diagnostics and remedies), pipe vibrations, pump characteristics and pump operation, design of intake structures, the effects of highly viscous flows, pumping of gas-liquid mixtures, hydraulic transport of solids, fatigue damage to impellers or diffusers, material selection under the aspects of fatigue, corrosion, erosion-corrosion or hydro-abrasive wear, pump selection, and hydraulic quality criteria. As a novelty, the 3rd ed. brings a fully analytical design method for radial impellers, which eliminates the arbitrary choices inherent to former design procedures. The d...

  7. Linear modeling of the soil-water partition coefficient normalized to organic carbon content by reversed-phase thin-layer chromatography.

    Science.gov (United States)

    Andrić, Filip; Šegan, Sandra; Dramićanin, Aleksandra; Majstorović, Helena; Milojković-Opsenica, Dušanka

    2016-08-05

    Soil-water partition coefficient normalized to the organic carbon content (KOC) is one of the crucial properties influencing the fate of organic compounds in the environment. Chromatographic methods are well established alternative for direct sorption techniques used for KOC determination. The present work proposes reversed-phase thin-layer chromatography (RP-TLC) as a simpler, yet equally accurate method as officially recommended HPLC technique. Several TLC systems were studied including octadecyl-(RP18) and cyano-(CN) modified silica layers in combination with methanol-water and acetonitrile-water mixtures as mobile phases. In total 50 compounds of different molecular shape, size, and various ability to establish specific interactions were selected (phenols, beznodiazepines, triazine herbicides, and polyaromatic hydrocarbons). Calibration set of 29 compounds with known logKOC values determined by sorption experiments was used to build simple univariate calibrations, Principal Component Regression (PCR) and Partial Least Squares (PLS) models between logKOC and TLC retention parameters. Models exhibit good statistical performance, indicating that CN-layers contribute better to logKOC modeling than RP18-silica. The most promising TLC methods, officially recommended HPLC method, and four in silico estimation approaches have been compared by non-parametric Sum of Ranking Differences approach (SRD). The best estimations of logKOC values were achieved by simple univariate calibration of TLC retention data involving CN-silica layers and moderate content of methanol (40-50%v/v). They were ranked far well compared to the officially recommended HPLC method which was ranked in the middle. The worst estimates have been obtained from in silico computations based on octanol-water partition coefficient. Linear Solvation Energy Relationship study revealed that increased polarity of CN-layers over RP18 in combination with methanol-water mixtures is the key to better modeling of

  8. Coding Partitions

    Directory of Open Access Journals (Sweden)

    Fabio Burderi

    2007-05-01

    Full Text Available Motivated by the study of decipherability conditions for codes weaker than Unique Decipherability (UD, we introduce the notion of coding partition. Such a notion generalizes that of UD code and, for codes that are not UD, allows to recover the ``unique decipherability" at the level of the classes of the partition. By tacking into account the natural order between the partitions, we define the characteristic partition of a code X as the finest coding partition of X. This leads to introduce the canonical decomposition of a code in at most one unambiguouscomponent and other (if any totally ambiguouscomponents. In the case the code is finite, we give an algorithm for computing its canonical partition. This, in particular, allows to decide whether a given partition of a finite code X is a coding partition. This last problem is then approached in the case the code is a rational set. We prove its decidability under the hypothesis that the partition contains a finite number of classes and each class is a rational set. Moreover we conjecture that the canonical partition satisfies such a hypothesis. Finally we consider also some relationships between coding partitions and varieties of codes.

  9. Centrifuge modeling of monopiles

    DEFF Research Database (Denmark)

    Klinkvort, Rasmus Tofte

    2010-01-01

    To gain a larger knowledge of the monopile foundation concept, centrifuge modeling is used by the geotechnical group at DTU. The centrifuge operated at DTU is a beam centrifuge and was built in 1976. In the recent years it has been upgraded with onboard data acquisition and control systems. The c...... from centrifuge tests performed on large diameter piles installed in dry sand.......To gain a larger knowledge of the monopile foundation concept, centrifuge modeling is used by the geotechnical group at DTU. The centrifuge operated at DTU is a beam centrifuge and was built in 1976. In the recent years it has been upgraded with onboard data acquisition and control systems....... The capabilities of the centrifuge at DTU makes it possible to obtain a scale factor of 85 in experiments which equals a soil volume in prototype scale of a diameter of 40 meters and a depth of 40 meters. This paper describes centrifuge modeling theory, the centrifuge setup at DTU and as an example show results...

  10. 应用新型立式逆流色谱制备分离南蛇藤中的南蛇藤素%Preparative isolation and purification of celastrol from Celastrus orbiculatus Thunb. by a new countercurrent chromatography with upright coil planet centrifuge

    Institute of Scientific and Technical Information of China (English)

    孙翠荣; 吴世华; 王奎武; 潘远江

    2003-01-01

    A versatile countercurrent chromatography with upright multilayer coil planet centrifuge, named upright countercurrent chromatography (UCCC), was applied to the isolation and purification of celastrol from the roots of Celastrus orbiculatus Thunb. The crude celastrol was obtained by elution with petroleum ether from ethanol extracts using a 15 cm length and 5 cm I.D. of silica gel flash chromatography. Preparative UCCC (Fig. 1) with a two-phase system composed of petroleum ether (b. p. 60 ~ 90 ℃ )-ethyl acetate-tetrachloromethanemethanol-water ( 1:1:8:6: 1, v/v) was successfully performed, yielding 705 mg celastrol at 99.5 % purity from 1020 rng of the crude extract in one step separation.

  11. METHOD OF CENTRIFUGE OPERATION

    Science.gov (United States)

    Cohen, K.

    1960-05-10

    A method of isotope separation is described in which two streams are flowed axially of, and countercurrently through, a cylindrical centrifuge bowl. Under the influence of a centrifugal field, the light fraction is concentrated in a stream flowing through the central portion of the bowl, whereas the heavy fraction is concentrated in a stream at the periphery thereof.

  12. Determination of polydimethylsiloxane–water partition coefficients for ten 1-chloro-4-[2,2,2-trichloro-1-(4-chlorophenyl)ethyl]benzene-related compounds and twelve polychlorinated biphenyls using gas chromatography/mass spectrometry

    Science.gov (United States)

    Eganhouse, Robert P.

    2016-01-01

    Polymer-water partition coefficients (Kpw) of ten DDT-related compounds were determined in pure water at 25 °C using commercial polydimethylsiloxane-coated optical fiber. Analyte concentrations were measured by thermal desorption-gas chromatography/full scan mass spectrometry (TD–GC/MSFS; fibers) and liquid injection-gas chromatography/selected ion monitoring mass spectrometry (LI–GC/MSSIM; water). Equilibrium was approached from two directions (fiber uptake and depletion) as a means of assessing data concordance. Measured compound-specific log Kpw values ranged from 4.8 to 6.1 with an average difference in log Kpw between the two approaches of 0.05 log units (∼12% of Kpw). Comparison of the experimentally-determined log Kpw values with previously published data confirmed the consistency of the results and the reliability of the method. A second experiment was conducted with the same ten DDT-related compounds and twelve selected PCB (polychlorinated biphenyl) congeners under conditions characteristic of a coastal marine field site (viz., seawater, 11 °C) that is currently under investigation for DDT and PCB contamination. Equilibration at lower temperature and higher ionic strength resulted in an increase in log Kpw for the DDT-related compounds of 0.28–0.49 log units (61–101% of Kpw), depending on the analyte. The increase in Kpw would have the effect of reducing by approximately half the calculated freely dissolved pore-water concentrations (Cfree). This demonstrates the importance of determining partition coefficients under conditions as they exist in the field.

  13. Chromatographic retention prediction and octanol-water partition coefficient determination of monobasic weak acidic compounds in ion-suppression reversed-phase liquid chromatography using acids as ion-suppressors.

    Science.gov (United States)

    Ming, Xin; Han, Shu-ying; Qi, Zheng-chun; Sheng, Dong; Lian, Hong-zhen

    2009-08-15

    Although simple acids, replacing buffers, have been widely applied to suppress the ionization of weakly ionizable acidic analytes in reversed-phase liquid chromatography (RPLC), none of the previously reported works focused on the systematic studies about the retention behavior of the acidic solutes in this ion-suppression RPLC mode. The subject of this paper was therefore to investigate the retention behavior of monobasic weak acidic compounds using acetic, perchloric and phosphoric acids as the ion-suppressors. The apparent octanol-water partition coefficient (K" ow) was proposed to calibrate the octanol-water partition coefficient (K(ow)) of these weak acidic compounds, which resulted in a better linear correlation with log k(w), the logarithm of the hypothetical retention factor corresponding to neat aqueous fraction of hydroorganic mobile phase. This log K" ow-log k w linear correlation was successfully validated by the results of monocarboxylic acids and monohydrating phenols, and moreover by the results under diverse experimental conditions for the same solutes. This straightforward relationship not only can be used to effectively predict the retention values of weak acidic solutes combined with Snyder-Soczewinski equation, but also can offer a promising medium for directly measuring K(ow) data of these compounds via Collander equation. In addition, the influence of the different ion-suppressors on the retention of weak acidic compounds was also compared in this RPLC mode.

  14. Partitioning of selected antioxidants in mayonnaise

    DEFF Research Database (Denmark)

    Jacobsen, Charlotte; Schwarz, K.; Stockmann, H.

    1999-01-01

    This study examined partitioning of alpha-, beta-, and gamma- tocopherol and six polar antioxidants (Trolox, ferulic acid, caffeic acid, propyl gallate, gallic acid, and catechin) in mayonnaise. Partitioning of antioxidants between different phases was determined after separation of mayonnaise...... by either (a) centrifugation + ultracentrifugation or (b) centrifugation + dialysis. Antioxidants partitioned in accordance with their chemical structure and polarity: Tocopherols were concentrated in the oil phase (93-96%), while the proportion of polar antioxidants in the oil phase ranged from 0% (gallic...... acid and catechin) to 83% (Trolox). Accordingly, proportions of 6% (Trolox) to 80% (gallic acid and catechin) were found in the aqueous phase. Similar trends were observed after dialysis. After ultracentrifugation, large proportions of polar antioxidants were found in the "emulsion phase...

  15. Centrifugal pump handbook

    CERN Document Server

    Pumps, Sulzer

    2010-01-01

    This long-awaited new edition is the complete reference for engineers and designers working on pump design and development or using centrifugal pumps in the field. This authoritative guide has been developed with access to the technical expertise of the leading centrifugal pump developer, Sulzer Pumps. In addition to providing the most comprehensive centrifugal pump theory and design reference with detailed material on cavitation, erosion, selection of materials, rotor vibration behavior and forces acting on pumps, the handbook also covers key pumping applications topics and operational

  16. Maryland Centrifugal Experiment

    Energy Technology Data Exchange (ETDEWEB)

    Hassam, Adil; Ellis, Richard F

    2016-12-22

    The Maryland Centrifugal Experiment (MCX) Project has investigated the concepts of centrifugal plasma confinement and stabilization of instabilities by velocity shear. The basic requirement is supersonic plasma rotation about a shaped, open magnetic field. Overall, the MCX Project attained three primary goals that were set out at the start of the project. First, supersonic rotation at Mach number upto 2.5 was obtained. Second, turbulence from flute interchange modes was found considerably reduced from conventional. Third, plasma pressure was contained along the field, as evidenced by density drops of x10 from the center to the mirror throats.

  17. Simultaneous determination of organotin compounds in textiles by gas chromatography-flame photometry following liquid/liquid partitioning with tert-butyl ethyl ether after reflux-extraction.

    Science.gov (United States)

    Hamasaki, Tetsuo

    2013-10-15

    A rapid and relatively clean method for determining six organotin compounds (OtC) in textile goods with a gas chromatograph equipped with a conventional flame photometric detector (GC-FPD) has been developed. After the reflux-extraction to use methanol containing 1% (v/v) of hydrochloric acid, five hydrophobic OtC (e.g. tributyltin: TBT) and slightly less hydrophobic dibutyltin (DBT) could be drawn out through partitioning between the methanolic buffer solution and tert-butyl ethyl ether instead of hazardous dichloromethane, of which usage is provided by the official-methods notified in Japan, and following the ethylation procedure to use sodium tetraethylborate, the OtC were determined with the GC-FPD. The recoveries of DBT, TBT, tetrabutyltin, triphenyltin, dioctyltin, and trioctyltin from textile products (cloth diaper, socks, and undershirt) were 60-77, 89-98, 86-94, 71-78, 85-109, and 70-79% respectively, and their coefficients of variation were 2.5-16.5%. Calibration curves for OtC were linear (0.01-0.20 μg as Sn mL(-1)), and the correlation coefficients were 0.9922-1.0000. Their detection limits were estimated to be 2.7-9.7 n gas Sn g(-1). These data suggested that this method would be applicable to their simultaneous determination. Five retailed textile goods were analyzed by this proposed method, and 0.013-0.65 µg as Sn g(-1) of OtC (e.g. DBT) were determined in three. Moreover, a possibility that various OtC including non-targeted species in textile would be specifically detected by applying the studying speciation-technique of controlling signal intensity-flame fuel gas pressures of the GC-FPD was found.

  18. Perceived radial translation during centrifugation

    NARCIS (Netherlands)

    Bos, J.E.; Correia Grácio, B.J.

    2015-01-01

    BACKGROUND: Linear acceleration generally gives rise to translation perception. Centripetal acceleration during centrifugation, however, has never been reported giving rise to a radial, inward translation perception. OBJECTIVE: To study whether centrifugation can induce a radial translation percepti

  19. Pumps, Centrifugal and Reciprocating

    Science.gov (United States)

    2011-04-27

    guidance for preparing test plans and conducting test programs to evaluate the effectiveness and suitability for military use of centrifugal and...This page is intentionally blank.)   US ARMY DEVELOPMENTAL TEST COMMAND TEST...Satisfy the needs of MIL-STD-4612. High-Altitude Electromagnetic Pulse ( HEMP ) Test Facility Satisfy the needs of MIL-STD-461. Rail Impact Test

  20. Centrifugal atomisation of alloys

    Energy Technology Data Exchange (ETDEWEB)

    Li Huiping [School of Mechanical and Materials Engineering, Univ. of Surrey, Guilford (United Kingdom); Dept. of Inorganic Materials, East China Univ. of Science and Technology, Shanghai, SH (China); Tsakiropoulos, P. [School of Mechanical and Materials Engineering, Univ. of Surrey, Guilford (United Kingdom); Johnson, T. [Tetronics Ltd., Faringdon, Oxfordshire (United Kingdom)

    2001-07-01

    Centrifugal atomisation using a rotating disk is described and compared to REP and PREP. Results of calculations of models describing the interaction of a melt with a rotating disk, the formation of thin film on the disk and the break up of the thin film and its atomisation at the edge of the disk are compared with experimental results. (orig.)

  1. Central centrifugal cicatricial alopecia

    Directory of Open Access Journals (Sweden)

    Collin Blattner

    2013-01-01

    Full Text Available Central centrifugal cicatricial alopecia is a common cause of progressive permanent apical alopecia. This unique form of alopecia includes entities previously know as "hot comb alopecia," "follicular degeneration syndrome," "pseudopelade" in African Americans and "central elliptical pseudopelade" in Caucasians. The etiology appears to be multifactorial and the condition occurs in all races.

  2. A new non-synchronous preparative counter-current centrifuge-the next generation of dynamic extraction/chromatography devices with independent mixing and settling control, which offer a step change in efficiency.

    Science.gov (United States)

    Ignatova, Svetlana; Hawes, David; van den Heuvel, Remco; Hewitson, Peter; Sutherland, Ian A

    2010-01-01

    A new and significantly more robust design of non-synchronous coil planet centrifuge is introduced where the degree of mixing between two immiscible phases can be changed independently from the "g" field required to separate out the phases. A hypothesis that an optimum ratio between the speed of the bobbin and the speed of the rotor can be found to optimise the efficiency of the separation for a given force field is upheld for an intermediate polarity phase system. This paves the way for extensive further research to find the optimum non-synchronous conditions for a range of different phase systems that are desirable for the separation of large molecules, proteins and biologics but can tend to emulsify in the standard "J" type centrifuge systems currently available and routinely in use for aqueous organic phase systems. A step change of up to 30% in resolution and 90% in plate efficiency is demonstrated.

  3. In vitro prediction of human intestinal absorption and blood-brain barrier partitioning: development of a lipid analog for micellar liquid chromatography.

    Science.gov (United States)

    De Vrieze, Mike; Janssens, Pieter; Szucs, Roman; Van der Eycken, Johan; Lynen, Frédéric

    2015-09-01

    Over the past decades, several in vitro methods have been tested for their ability to predict either human intestinal absorption (HIA) or penetration across the blood-brain barrier (BBB) of drugs. Micellar liquid chromatography (MLC) has been a successful approach for retention time measurements of drugs to establish models together with other molecular descriptors. Thus far, MLC approaches have only made use of commercial surfactants such as sodium dodecyl sulfate (SDS) and polyoxyethylene (23) lauryl ether (Brij35), which are not representative for the phospholipids present in human membranes. Miltefosine, a phosphocholine-based lipid, is presented here as an alternative surfactant for MLC measurements. By using the obtained retention factors and several computed descriptors for a set of 48 compounds, two models were constructed: one for the prediction of HIA and another for the prediction of penetration across the BBB expressed as log BB. All data were correlated to experimental HIA and log BB values, and the performance of the models was evaluated. Log BB prediction performed better than HIA prediction, although HIA prediction was also improved a lot (from 0.5530 to 0.7175) compared to in silico predicted HIA values.

  4. Centrifugal unbalance detection system

    Science.gov (United States)

    Cordaro, Joseph V.; Reeves, George; Mets, Michael

    2002-01-01

    A system consisting of an accelerometer sensor attached to a centrifuge enclosure for sensing vibrations and outputting a signal in the form of a sine wave with an amplitude and frequency that is passed through a pre-amp to convert it to a voltage signal, a low pass filter for removing extraneous noise, an A/D converter and a processor and algorithm for operating on the signal, whereby the algorithm interprets the amplitude and frequency associated with the signal and once an amplitude threshold has been exceeded the algorithm begins to count cycles during a predetermined time period and if a given number of complete cycles exceeds the frequency threshold during the predetermined time period, the system shuts down the centrifuge.

  5. Centrifugally decoupling touchdown bearings

    Science.gov (United States)

    Post, Richard F

    2014-06-24

    Centrifugally decoupling mechanical bearing systems provide thin tensioned metallic ribbons contained in a support structure. This assembly rotates around a stationary shaft being centered at low speeds by the action of the metal ribbons. Tension springs are connected on one end to the ribbons and on the other end to the support structure. The ribbons pass through slots in the inner ring of the support structure. The spring preloading thus insures contact (or near-contact) between the ribbons and the shaft at rotation speeds below the transition speed. Above this speed, however, the centrifugal force on the ribbons produces a tensile force on them that exceeds the spring tensile force so that the ribbons curve outward, effectively decoupling them from mechanical contact with the shaft. They still remain, however, in position to act as a touchdown bearing in case of abnormally high transverse accelerations.

  6. CENTRIFUGAL MEMBRANE FILTRATION

    Energy Technology Data Exchange (ETDEWEB)

    Daniel J. Stepan; Bradley G. Stevens; Melanie D. Hetland

    1999-10-01

    The overall project consists of several integrated research phases related to the applicability, continued development, demonstration, and commercialization of the SpinTek centrifugal membrane filtration process. Work performed during this reporting period consisted of Phase 2 evaluation of the SpinTek centrifugal membrane filtration technology and Phase 3, Technology Partnering. During Phase 1 testing conducted at the EERC using the SpinTek ST-IIL unit operating on a surrogate tank waste, a solids cake developed on the membrane surface. The solids cake was observed where linear membrane velocities were less than 17.5 ft/s and reduced the unobstructed membrane surface area up to 25%, reducing overall filtration performance. The primary goal of the Phase 2 research effort was to enhance filtration performance through the development and testing of alternative turbulence promoter designs. The turbulence promoters were designed to generate a shear force across the entire membrane surface sufficient to maintain a self-cleaning membrane capability and improve filtration efficiency and long-term performance. Specific Phase 2 research activities included the following: System modifications to accommodate an 11-in.-diameter, two-disk rotating membrane assembly; Development and fabrication of alternative turbulence promoter designs; Testing and evaluation of the existing and alternative turbulence promoters under selected operating conditions using a statistically designed test matrix; and Data reduction and analysis; The objective of Phase 3 research was to demonstrate the effectiveness of SpinTek's centrifugal membrane filtration as a pretreatment to remove suspended solids from a liquid waste upstream of 3M's WWL cartridge technology for the selective removal of technetium (Tc).

  7. Central centrifugal cicatricial alopecia.

    Science.gov (United States)

    Whiting, David A; Olsen, Elise A

    2008-01-01

    A progressive scarring alopecia of the central scalp is commonly seen in young to middle-aged females of African descent. It usually starts at the vertex or mid top of the scalp and gradually spreads centrifugally, hence, the unifying term of central centrifugal cicatricial alopecia. The clinical pattern is suggestive of female pattern alopecia, but a lack of follicular pores indicative of scarring is present. It can progress for years before slowly burning out. The etiology is unknown but genetic factors may be important. It is often associated with a history of traumatic hairstyling involving heat, traction, and chemicals. However, most patients of African descent without this disorder have similar styling habits. Nonetheless, avoidance of physical and chemical trauma to the scalp hair, the use of suitable shampoos and conditioners, and the encouragement of natural hairstyles may be helpful. Any infection should be treated. Topical or intralesional corticosteroids and systemic antibiotics may be useful and topical minoxidil should be tried with the hope of preventing further scarring and encouraging regrowth of recovering follicles. Current research into the etiology of this disorder will help to foster much-needed clinical trials of therapeutic agents.

  8. Centrifugal shot blast system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-02-01

    This report describes a demonstration of Concrete cleaning, Inc., modified centrifugal shot blast technology to remove the paint coating from concrete flooring. This demonstration is part of the Chicago Pile-5 (CP-5) Large-Scale Demonstration Project (LSDP) sponsored by the US Department of Energy (DOE), office of Science and Technology (OST), Deactivation and Decommissioning Focus Area (DDFA). The objective of the LSDP is to select and demonstrate potentially beneficial technologies at the Argonne National Laboratory-East (ANL) CP-5 Research Reactor. The purpose of the LSDP is to demonstrate that using innovative and improved decontamination and decommissioning (D and D) technologies from various sources can result in significant benefits, such as decreased cost and increased health and safety, as compared with baseline D and D technologies. Potential markets exist for the innovative centrifugal shot blast system at the following sites: Fernald Environmental Management Project, Los Alamos, Nevada, Oak Ridge Y-12 and K-25, Paducah, Portsmouth Gaseous Diffusion site, and the Savannah River Site. This information is based on a revision to the OST Linkage Tables dated August 4, 1997.

  9. Unique Path Partitions

    DEFF Research Database (Denmark)

    Bessenrodt, Christine; Olsson, Jørn Børling; Sellers, James A.

    2013-01-01

    We give a complete classification of the unique path partitions and study congruence properties of the function which enumerates such partitions.......We give a complete classification of the unique path partitions and study congruence properties of the function which enumerates such partitions....

  10. Rapid determination of octanol-water partition coefficient using vortex-assisted liquid-liquid microextraction.

    Science.gov (United States)

    Román, Iván P; Mastromichali, Anna; Tyrovola, Konstantina; Canals, Antonio; Psillakis, Elefteria

    2014-02-21

    Vortex-assisted liquid-liquid microextraction (VALLME) coupled with high-performance liquid chromatography (HPLC) is proposed here for the rapid determination of octanol-water partitioning coefficients (Kow). VALLME uses vortex agitation, a mild emulsification procedure, to disperse microvolumes of octanol in the aqueous phase thus increasing the interfacial contact area and ensuring faster partitioning rates. With VALLME, 2min were enough to achieve equilibrium conditions between the octanolic and aqueous phases. Upon equilibration, separation was achieved using centrifugation and the octanolic microdrop was collected and analyzed in a HPLC system. Six model compounds with logKow values ranging between ∼0.5 and 3.5 were used during the present investigations. The proposed method produced logKow values that were consistent with previously published values and the recorded uncertainty was well within the acceptable log unit range. Overall, the key features of the proposed Kow determination procedure comprised speed, reliability, simplicity, low cost and minimal solvent consumption.

  11. Centrifugal microfluidics for biomedical applications.

    Science.gov (United States)

    Gorkin, Robert; Park, Jiwoon; Siegrist, Jonathan; Amasia, Mary; Lee, Beom Seok; Park, Jong-Myeon; Kim, Jintae; Kim, Hanshin; Madou, Marc; Cho, Yoon-Kyoung

    2010-07-21

    The centrifugal microfluidic platform has been a focus of academic and industrial research efforts for almost 40 years. Primarily targeting biomedical applications, a range of assays have been adapted on the system; however, the platform has found limited commercial success as a research or clinical tool. Nonetheless, new developments in centrifugal microfluidic technologies have the potential to establish wide-spread utilization of the platform. This paper presents an in-depth review of the centrifugal microfluidic platform, while highlighting recent progress in the field and outlining the potential for future applications. An overview of centrifugal microfluidic technologies is presented, including descriptions of advantages of the platform as a microfluidic handling system and the principles behind centrifugal fluidic manipulation. The paper also discusses a history of significant centrifugal microfluidic platform developments with an explanation of the evolution of the platform as it pertains to academia and industry. Lastly, we review the few centrifugal microfluidic-based sample-to-answer analysis systems shown to date and examine the challenges to be tackled before the centrifugal platform can be more broadly accepted as a new diagnostic platform. In particular, fully integrated, easy to operate, inexpensive and accurate microfluidic tools in the area of in vitro nucleic acid diagnostics are discussed.

  12. Unshrouded Centrifugal Turbopump Impeller

    Science.gov (United States)

    Prueger, George; Williams, Morgan; Chen, Wei; Paris, John; Stewart, Eric; Williams, Robert

    1999-01-01

    The ratio of rocket engine thrust to weight is a limiting constraint in placing more payload into orbit at a low cost. A key component of an engine's overall weight is the turbopump weight, Reducing the turbopump weight can result in significant engine weight reduction and hence, increased delivered payload. There are two main types of pumps: centrifugal and axial pumps. These types of pumps can be further sub-divided into those with shrouds and those without shrouds (unshrouded pumps). Centrifugal pumps can achieve the same pump discharge pressure as an axial pump and it requires fewer pump stages and lower pump weight than an axial pump. Also, with unshrouded centrifugal pumps (impeller), the number of stages and weight can be further reduced. However. there are several issues with regard to using an unshrouded impeller: 1) there is a pump performance penalty due to the front open face recirculation flow; 2) there is a potential pump axial thrust problem from the unbalanced front open face and the back shroud face; and, 3) since test data is very linu'ted for this configuration, there is uncertainty in the magnitude and phase of the rotordynamics forces due to the front impeller passage. The purpose of the paper is to discuss the design of an unshrouded impeller and to examine the design's hydrodynamic performance, axial thrust, and rotordynamics performance. The design methodology will also be discussed. This work will help provide some guidelines for unshrouded impeller design. In particular, the paper will discuss the design of three unshrouded impellers - one with 5 full and 5 partial blades (5+5). one with 6+6 blades and one with 8+8 blades. One of these designs will be selected for actual fabrication and flow test. Computational fluid dynamics (CFD) is used to help design and optimize the unshrouded impeller. The relative pump performance penalty is assessed by comparing the CFD results of the unshrouded impeller with the equivalent shrouded impeller for a

  13. [Galileo and centrifugal force].

    Science.gov (United States)

    Vilain, Christiane

    This work intends to focus on Galileo's study of what is now called "centrifugal force," within the framework of the Second Day of his Dialogo written in 1632, rather than on the previously published commentaries on the topic. Galileo proposes three geometrical demonstrations in order to prove that gravity will always overcome centrifugalforce, and that the potential rotation of the Earth, whatever its speed, cannot in any case project objects beyond it. Each of these demonstrations must consequently contain an error and it has seemed to us that the first one had not been understood up until now. Our analysis offers an opportunity to return to Galileo's geometrical representation of dynamical questions; actually, we get an insight into the sophistication of Galileo's practices more than into his mistakes. Our second point, concerning the historiography of the problem, shows an evolution from anachronic critics to more contextual considerations, in the course of the second half of the twentieth century.

  14. Gas centrifuge purge method

    Science.gov (United States)

    Theurich, Gordon R.

    1976-01-01

    1. In a method of separating isotopes in a high speed gas centrifuge wherein a vertically oriented cylindrical rotor bowl is adapted to rotate about its axis within an evacuated chamber, and wherein an annular molecular pump having an intake end and a discharge end encircles the uppermost portion of said rotor bowl, said molecular pump being attached along its periphery in a leak-tight manner to said evacuated chamber, and wherein end cap closure means are affixed to the upper end of said rotor bowl, and a process gas withdrawal and insertion system enters said bowl through said end cap closure means, said evacuated chamber, molecular pump and end cap defining an upper zone at the discharge end of said molecular pump, said evacuated chamber, molecular pump and rotor bowl defining a lower annular zone at the intake end of said molecular pump, a method for removing gases from said upper and lower zones during centrifuge operation with a minimum loss of process gas from said rotor bowl, comprising, in combination: continuously measuring the pressure in said upper zone, pumping gas from said lower zone from the time the pressure in said upper zone equals a first preselected value until the pressure in said upper zone is equal to a second preselected value, said first preselected value being greater than said second preselected value, and continuously pumping gas from said upper zone from the time the pressure in said upper zone equals a third preselected value until the pressure in said upper zone is equal to a fourth preselected value, said third preselected value being greater than said first, second and fourth preselected values.

  15. High Performance Liquid Chromatography

    Science.gov (United States)

    Talcott, Stephen

    High performance liquid chromatography (HPLC) has many applications in food chemistry. Food components that have been analyzed with HPLC include organic acids, vitamins, amino acids, sugars, nitrosamines, certain pesticides, metabolites, fatty acids, aflatoxins, pigments, and certain food additives. Unlike gas chromatography, it is not necessary for the compound being analyzed to be volatile. It is necessary, however, for the compounds to have some solubility in the mobile phase. It is important that the solubilized samples for injection be free from all particulate matter, so centrifugation and filtration are common procedures. Also, solid-phase extraction is used commonly in sample preparation to remove interfering compounds from the sample matrix prior to HPLC analysis.

  16. Microwave assisted centrifuge and related methods

    Science.gov (United States)

    Meikrantz, David H [Idaho Falls, ID

    2010-08-17

    Centrifuge samples may be exposed to microwave energy to heat the samples during centrifugation and to promote separation of the different components or constituents of the samples using a centrifuge device configured for generating microwave energy and directing the microwave energy at a sample located in the centrifuge.

  17. Development of a WES Centrifuge,

    Science.gov (United States)

    1992-09-01

    centrifuge chamber during a long centrifuge flight ANS&A have suggested that a more practical and economical alternative would be to provide thermal barriers around...specifications and costs can be prepared, as follows; (10) Constant temperature and temperature gradient control system based on thermal barriers both...CONTROL SYSTEM Design study by ANS&A for constant temperature and temperature gradient control system based on thermal barriers both external to and

  18. 低温离心净化-高效液相色谱法快速测定腐竹中的碱性橙II和碱性嫩黄O%Rapid determination of chrysoidine II and auramine O in dried bean curd sticks by cryogenic centrifugal purification-high performance liquid chromatography

    Institute of Scientific and Technical Information of China (English)

    杨爽; 俞子萱; 王永芳; 葛宝坤

    2015-01-01

    ABSTRACT:Objective Toestablish a method to detect chrysoidine II and auramine O in dried bean curd sticks by cryogenic centrifugal purification–high performance liquid chromatography. Methods The samples werediluted and extracted by 70% acetonitrile ammonia water, purified by centrifugation at 12000 r/min and 4℃, separated by high performance liquid chromatography (HPLC), and detected by photodiode array detector (PDA). The method took the retention time (Rt) for qualitative and external standard method quantitative analysis.Results Within the limits of concentration 0.00125~0.05 mg/mL, the standard curve had a good linear relationship, and the correlation coefficient was more than 0.9999; in the level of 0.05, 2.0, and 10.0 mg/kg, the add mark recovery rate was from 95.0% to 103.0%(n=10), the relative standard deviation was less than 5.0%; limit of detection(LOD) was 0.02 mg/kg, limit of quantitation (LOQ) was 0.05 mg/kg.Conclusion Comparing the actual sample testing results with reference method, this method is simple, rapid, sensitive, with low cost, and is suitable for popularization and application.%目的:建立腐竹中碱性橙 II 和碱性嫩黄 O 的低温离心净化-高效液相色谱测定方法。方法样品经70%的乙腈-氨水(0.5%)提取,4℃低温、12000 r/min离心净化,高效液相色谱(high performance liquid chromatography, HPLC)分离,最后采用二极管阵列检测器(PDA)检测,以保留时间(Rt)定性,外标法定量。结果在0.00125~0.05 mg/mL的浓度范围内,标准曲线有良好的线性关系,相关系数大于0.9999;样品在0.05、2.0、10.0 mg/kg三个加标水平内的回收率范围为95.0%~103.0%(n=10),相对标准偏差小于5.0%。方法的检出限(LOD)为0.02 mg/kg,定量限(LOQ)为0.05 mg/kg。结论对实际样品测试结果与参考文献方法比较,该方法具有简便、快速、灵敏、费用低,便于推广应用。

  19. Hyperbolically Shaped Centrifugal Compressor

    Institute of Scientific and Technical Information of China (English)

    Romuald Puzyrewski; Pawel Flaszy(n)ski

    2003-01-01

    Starting from the classical centrifugal compressor, cone shaped in meridional cross section, two modifications are considered on the basis of results from 2D and 3D flow models. The first modification is the change of the meridional cross section to hyperbolically shaped channel. The second modification, proposed on the basis of 2D axisymmetric solution, concerns the shape of blading. On the strength of this solution the blades are formed as 3D shaped blades, coinciding with the recent tendency in 3D designs. Two aims were considered for the change of meridional compressor shape. The first was to remove the separation zone which appears as the flow tums from axial to radial direction. The second aim is to uniformize the flow at exit of impeller. These two goals were considered within the frame of 2D axisymmetric model. Replacing the cone shaped compressor by a hyperbolically shaped one, the separation at the corner was removed. The disc and shroud shape of the compressor was chosen in the way which satisfies the condition of most uniform flow at the compressor exit. The uniformity of exit flow from the rotor can be considered as the factor which influences the performance of the diffuser following the rotor. In the 2D model a family of stream surfaces of S1 type is given in order to find S2 surfaces which may be identified with the midblade surfaces of compressor blading. A computation of 3D type has been performed in order to establish the relations between 2D and 3D models in the calculation of flow parameters. In the presented example the 2D model appears as the inverse model which leads to 3D shape of blading whereas the 3D model has been used for the direct solution. In the presented example the confrontation of two models, 2D and 3D, leads to a better understanding of the application of these models to the design procedure.

  20. Centrifugation. A theoretical study of oxygen enrichment by centrifugation

    Energy Technology Data Exchange (ETDEWEB)

    Kierkegaard, P.; Raetz, E.

    1998-12-01

    In the present paper we first investigate what happens if we fill a cylinder with air, close it and rotate it. The results show that no matter which peripheral speed is used, it is not possible by means of the radial separation effect alone, to enrich the oxygen concentration from the previous 21% to more then 23.3%, which is of no practical value. In case of a too low enrichment in one centrifuge, the wanted material from this centrifuge can be used as an input for a second centrifuge and so on, in this way forming a cascade of centrifuges. Oxygen will be enriched in each step, until the desired concentration is reached. Cascading was the technology in the very beginning by enrichment plants for uraniumhexaflouride, used for atomic weapons and nuclear power plants. In this study we try to avoid cascading by aiming for higher separation factors. Therefore, we next investigate the possibilities of using a countercurrent centrifuge where in principle the enriched gas is subjected to several centrifugation in the same centrifuge. The calculations show, that in this way it is possible to produce nearly a 100% pure oxygen (polluted with some heavier molecules like argon) in one machine. Our third step was to calculate the amount of oxygen produced per hour. Using a countercurrent centrifuge of the Zippe type, 100 cm high and 20 cm in diameter, it is or will be possible in the near future to produce 17 g enriched air per hour enriched to 50% oxygen. That corresponds to processing 1 m{sup 3} atmospherical air in the period of approximately 24 hours. This is not very impressive. Our fourth step was to estimate the amount of power used for producing this amount of oxygen. A rough, but complicated, estimate shows that the power consumption at the production level will be about the double of the consumption used today. The overall conclusion is, that centrifugation as a production method for oxygen (or nitrogen) will not be competitive with the currently used method in the

  1. Using quantitative structure activity relationship models to predict an appropriate solvent system from a common solvent system family for countercurrent chromatography separation.

    Science.gov (United States)

    Marsden-Jones, Siân; Colclough, Nicola; Garrard, Ian; Sumner, Neil; Ignatova, Svetlana

    2015-06-12

    Countercurrent chromatography (CCC) is a form of liquid-liquid chromatography. It works by running one immiscible solvent (mobile phase) over another solvent (stationary phase) being held in a CCC column using centrifugal force. The concentration of compound in each phase is characterised by the partition coefficient (Kd), which is the concentration in the stationary phase divided by the concentration in the mobile phase. When Kd is between approximately 0.2 and 2, it is most likely that optimal separation will be achieved. Having the Kd in this range allows the compound enough time in the column to be separated without resulting in a broad peak and long run time. In this paper we report the development of quantitative structure activity relationship (QSAR) models to predict logKd. The QSAR models use only the molecule's 2D structure to predict the molecular property logKd.

  2. Centrifuge-Based Fluidic Platforms

    Science.gov (United States)

    Zoval, Jim; Jia, Guangyao; Kido, Horacio; Kim, Jitae; Kim, Nahui; Madou, Marc

    In this chapter centrifuge-based microfluidic platforms are reviewed and compared with other popular microfluidic propulsion methods. The underlying physical principles of centrifugal pumping in microfluidic systems are presented and the various centrifuge fluidic functions such as valving, decanting, calibration, mixing, metering, heating, sample splitting, and separation are introduced. Those fluidic functions have been combined with analytical measurements techniques such as optical imaging, absorbance and fluorescence spectroscopy and mass spectrometry to make the centrifugal platform a powerful solution for medical and clinical diagnostics and high-throughput screening (HTS) in drug discovery. Applications of a compact disc (CD)-based centrifuge platform analyzed in this review include: two-point calibration of an optode-based ion sensor, an automated immunoassay platform, multiple parallel screening assays and cellular-based assays. The use of modified commercial CD drives for high-resolution optical imaging is discussed as well. From a broader perspective, we compare the technical barriers involved in applying microfluidics for sensing and diagnostic as opposed to applying such techniques to HTS. The latter poses less challenges and explains why HTS products based on a CD fluidic platform are already commercially available, while we might have to wait longer to see commercial CD-based diagnostics.

  3. MEANS FOR DETERMINING CENTRIFUGE ALIGNMENT

    Science.gov (United States)

    Smith, W.Q.

    1958-08-26

    An apparatus is presented for remotely determining the alignment of a centrifuge. The centrifage shaft is provided with a shoulder, upon which two followers ride, one for detecting radial movements, and one upon the shoulder face for determining the axial motion. The followers are attached to separate liquid filled bellows, and a tube connects each bellows to its respective indicating gage at a remote location. Vibrations produced by misalignment of the centrifuge shaft are transmitted to the bellows, and tbence through the tubing to the indicator gage. This apparatus is particularly useful for operation in a hot cell where the materials handled are dangerous to the operating personnel.

  4. Generalized anti-centrifugal potential

    Energy Technology Data Exchange (ETDEWEB)

    Dandoloff, Rossen [Laboratoire de Physique Theorique et Modelisation, Universite de Cergy-Pontoise, F-95302 Cergy-Pontoise (France); Jensen, Bjørn [Department of Micro and Nano Systems Technology, Vestfold University College, N-3103 Tønsberg (Norway); Saxena, Avadh, E-mail: avadh@lanl.gov [Theoretical Division and Center for Nonlinear Studies, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

    2014-01-24

    We generalize the quantum anti-centrifugal potential in the two-dimensional Euclidean plane to two-dimensional surfaces embedded in three-dimensional Euclidean space. We consider the sphere with two caps removed in some detail. We show that quantum particles in this space are “pushed” towards either of the cap boundaries. We also consider the two-dimensional Euclidean plane with an elliptic area removed and compute the quantum anti-centrifugal potential on the elliptic boundary. It is argued that a sufficiently thin electrically conducting nano-wire shaped as an ellipse will exhibit an inhomogeneous charge distribution due to this quantum potential.

  5. Theory of batchwise centrifugal casting

    NARCIS (Netherlands)

    Biesheuvel, P. Maarten; Nijmeijer, Arian; Verweij, Henk

    1998-01-01

    In batchwise centrifugal casting a cylindrical mold is filled with suspension and rotated rapidly around its axis. This results in the movement of the particulate phase toward the cylinder wall and the formation of a tubular cast. Theory is presented for particle transport in the suspension phase an

  6. CENTRIFUGAL CASTING OF ANTIFRICTION SILUMIN

    Directory of Open Access Journals (Sweden)

    V. Ju. Stetsenko

    2010-01-01

    Full Text Available It is shown that the way of centrifugal casting into water-cooled mould with vertical rotation axis enables to receive hollow slugs with diameter 100–250 mm, with height under 200 mm with wall thickness under 15 mm of antifriction silumin АК15М3, which will replace expensive antifriction bronze.

  7. A strategy for the separation of diterpenoid isomers from the root of Aralia continentalis by countercurrent chromatography: The distribution ratio as a substitute for the partition coefficient and a three-phase solvent system.

    Science.gov (United States)

    Lee, Kyoung Jin; Song, Kwang Ho; Choi, Wonmin; Kim, Yeong Shik

    2015-08-07

    Aralia continentalis (Araliaceae) is widely used as a medicinal plant in East Asia. Previous studies have indicated that diterpenoid isomers (kaurenoic acid, continentalic acid, and ent-continentalic acid) are the major bioactive compounds of this plant. A new strategy was developed to alleviate difficulties in the separation of these isomers from this plant. A three-phase solvent system was applied to separate the isomers, and furthermore, the distribution ratio (Kc) was introduced as a substitute for the partition coefficient (KD). For compounds exhibiting a single equilibrium, their distributions in two immiscible phases were only affected by the partition coefficient of each solute. However, compounds that have a dissociating functional group (e.g., -COOH) are involved in two types of equilibrium in the two-phase system. In this case, the partitioning behaviors of the solutes are greatly affected by the pH of the solution. A mathematical prediction was applied for adjusting the solutions to the proper pH values. To prevent non-used phase (medium phase) waste, both the stationary phase (upper phase) and mobile phase (lower phase) were prepared on-demand without pre-saturation with the application of (1)H NMR. Each fraction obtained was collected and dried, yielding the following diterpenoid isomers from the 50mg injected sample: kaurenoic acid (19.7mg, yield: 39%) and ent-continentalic acid (21.3mg, yield: 42%).

  8. Computational prediction of solubilizers' effect on partitioning.

    Science.gov (United States)

    Hoest, Jan; Christensen, Inge T; Jørgensen, Flemming S; Hovgaard, Lars; Frokjaer, Sven

    2007-02-01

    A computational model for the prediction of solubilizers' effect on drug partitioning has been developed. Membrane/water partitioning was evaluated by means of immobilized artificial membrane (IAM) chromatography. Four solubilizers were used to alter the partitioning in the IAM column. Two types of molecular descriptors were calculated: 2D descriptors using the MOE software and 3D descriptors using the Volsurf software. Structure-property relationships between each of the two types of descriptors and partitioning were established using partial least squares, projection to latent structures (PLS) statistics. Statistically significant relationships between the molecular descriptors and the IAM data were identified. Based on the 2D descriptors structure-property relationships R(2)Y=0. 99 and Q(2)=0.82-0.83 were obtained for some of the solubilizers. The most important descriptor was related to logP. For the Volsurf 3D descriptors models with R(2)Y=0.53-0.64 and Q(2)=0.40-0.54 were obtained using five descriptors. The present study showed that it is possible to predict partitioning of substances in an artificial phospholipid membrane, with or without the use of solubilizers.

  9. Partitive descriptions in Korean

    Directory of Open Access Journals (Sweden)

    Keun Young Shin

    2017-02-01

    Full Text Available This paper examines Korean partitive constructions to investigate the typology of the partitive structure. In Korean, a quantifier precedes the nominal in a non-partitive, but it follows the nominal in a partitive. The relative order between a quantifier and its associated nominal indicates that a quantifier in Korean partitive does not function as a NP adjunct but takes a DP as its argument. I argue that Korean postnominal (floating quantifier constructions can be interpreted as partitives or pseudo-partitives/quantitatives because a postnominal (floating quantifier denoting a part-of relation can occur with a kind-denoting DP as well as a definite DP. I also propose that a quantifier denoting a part-of relation is associated with the argument of a verb via composition with a verbal predicate in the floating quantifier construction. This approach can provide an account for several idiosyncratic properties of floating quantifier constructions, which are difficult to capture under the assumption that a floating quantifier construction is derived by moving a quantifier away from its associated nominal. This article is part of the Special Collection: Partitives

  10. Design of a centrifugal blood pump: Heart Turcica Centrifugal.

    Science.gov (United States)

    Demir, Onur; Biyikli, Emre; Lazoglu, Ismail; Kucukaksu, Suha

    2011-07-01

    A prototype of a new implantable centrifugal blood pump system named Heart Turcica Centrifugal (HTC) was developed as a left ventricular assist device (LVAD) for the treatment of end-stage cardiac failure. In the development of HTC, effects of blade height and volute tongue profiles on the hydraulic and hemolytic performances of the pump were investigated. As a result, the prototype was manufactured using the best blade height and volute tongue profiles. Performance of the prototype model was experimentally evaluated in a closed-loop flow system using water as the medium. The hydraulic performance requirement of an LVAD (5 L/min flow rate against a pressure difference of 100 mm Hg) was attained at 2800 rpm rotational speed.

  11. Centrifugal separator devices, systems and related methods

    Science.gov (United States)

    Meikrantz, David H.; Law, Jack D.; Garn, Troy G.; Todd, Terry A.; Macaluso, Lawrence L.

    2012-03-20

    Centrifugal separator devices, systems and related methods are described. More particularly, fluid transfer connections for a centrifugal separator system having support assemblies with a movable member coupled to a connection tube and coupled to a fixed member, such that the movable member is constrained to movement along a fixed path relative to the fixed member are described. Also, centrifugal separator systems including such fluid transfer connections are described. Additionally, methods of installing, removing and/or replacing centrifugal separators from centrifugal separator systems are described.

  12. Combinatorics of set partitions

    CERN Document Server

    Mansour, Toufik

    2012-01-01

    Focusing on a very active area of mathematical research in the last decade, Combinatorics of Set Partitions presents methods used in the combinatorics of pattern avoidance and pattern enumeration in set partitions. Designed for students and researchers in discrete mathematics, the book is a one-stop reference on the results and research activities of set partitions from 1500 A.D. to today. Each chapter gives historical perspectives and contrasts different approaches, including generating functions, kernel method, block decomposition method, generating tree, and Wilf equivalences. Methods and d

  13. Centrifugal pumps and allied machinery

    CERN Document Server

    Anderson, HH

    1994-01-01

    This book will be of vital interest to all engineers and designers concerned with centrifugal pumps and turbines. Including statistical information derived from 20000 pumps and 700 turbines with capacities of 5gpm to 5000000gpm, this book offers the widest range and scope of information currently available. Statistical analyses suggest practical methods of increasing pump performance and provide valuable data for new design aspects.

  14. Fuzzy Partition Models for Fitting a Set of Partitions.

    Science.gov (United States)

    Gordon, A. D.; Vichi, M.

    2001-01-01

    Describes methods for fitting a fuzzy consensus partition to a set of partitions of the same set of objects. Describes and illustrates three models defining median partitions and compares these methods to an alternative approach to obtaining a consensus fuzzy partition. Discusses interesting differences in the results. (SLD)

  15. Bosonic Partition Functions

    CERN Document Server

    Kellerstein, M; Verbaarschot, J J M

    2016-01-01

    The behavior of quenched Dirac spectra of two-dimensional lattice QCD is consistent with spontaneous chiral symmetry breaking which is forbidden according to the Coleman-Mermin-Wagner theorem. One possible resolution of this paradox is that, because of the bosonic determinant in the partially quenched partition function, the conditions of this theorem are violated allowing for spontaneous symmetry breaking in two dimensions or less. This goes back to work by Niedermaier and Seiler on nonamenable symmetries of the hyperbolic spin chain and earlier work by two of the auhtors on bosonic partition functions at nonzero chemical potential. In this talk we discuss chiral symmetry breaking for the bosonic partition function of QCD at nonzero isospin chemical potential and a bosonic random matrix theory at imaginary chemical potential and compare the results with the fermionic counterpart. In both cases the chiral symmetry group of the bosonic partition function is noncompact.

  16. Carbon partitioning in photosynthesis.

    Science.gov (United States)

    Melis, Anastasios

    2013-06-01

    The work seeks to raise awareness of a fundamental problem that impacts the renewable generation of fuels and chemicals via (photo)synthetic biology. At issue is regulation of the endogenous cellular carbon partitioning between different biosynthetic pathways, over which the living cell exerts stringent control. The regulation of carbon partitioning in photosynthesis is not understood. In plants, microalgae and cyanobacteria, methods need be devised to alter photosynthetic carbon partitioning between the sugar, terpenoid, and fatty acid biosynthetic pathways, to lower the prevalence of sugar biosynthesis and correspondingly upregulate terpenoid and fatty acid hydrocarbons production in the cell. Insight from unusual but naturally occurring carbon-partitioning processes can help in the design of blueprints for improved photosynthetic fuels and chemicals production.

  17. Centrifuge facilities at Technical University of Denmark

    DEFF Research Database (Denmark)

    Leth, Caspar Thrane; Krogsbøll, Anette Susanne; Hededal, Ole

    2008-01-01

    The geotechnical group at the Danish Technical University (DTU) operates a geotechnical beam centrifuge. The centrifuge was build in 1976 and has been upgraded through the years, latest with onboard data and control systems. The centrifuge concept involves an increased gravity field in which...... the physical model is placed and tested. The capabilities of the centrifuge at DTU makes it possible to obtain a scale factor of 75-85 in the tests which equals a soil volume in prototype scale of ø40m and a depth of 36 m. The centrifuge facilities at DTU have through the years been used for testing various...... geotechnical issues, such as suction anchors, tension piles in clay, active earth pressures on sheet piles and group effects for lateral loaded piles. The paper describes physical modelling in general, the centrifuge, present setups and shows samples of obtained results....

  18. Empirical Design Considerations for Industrial Centrifugal Compressors

    Directory of Open Access Journals (Sweden)

    Cheng Xu

    2012-01-01

    Full Text Available Computational Fluid Dynamics (CFD has been extensively used in centrifugal compressor design. CFD provides further optimisation opportunities for the compressor design rather than designing the centrifugal compressor. The experience-based design process still plays an important role for new compressor developments. The wide variety of design subjects represents a very complex design world for centrifugal compressor designers. Therefore, some basic information for centrifugal design is still very important. The impeller is the key part of the centrifugal stage. Designing a highly efficiency impeller with a wide operation range can ensure overall stage design success. This paper provides some empirical information for designing industrial centrifugal compressors with a focus on the impeller. A ported shroud compressor basic design guideline is also discussed for improving the compressor range.

  19. Centrifugal quantum states of neutrons

    Science.gov (United States)

    Nesvizhevsky, V. V.; Petukhov, A. K.; Protasov, K. V.; Voronin, A. Yu.

    2008-09-01

    We propose a method for observation of the quasistationary states of neutrons localized near a curved mirror surface. The bounding effective well is formed by the centrifugal potential and the mirror Fermi potential. This phenomenon is an example of an exactly solvable “quantum bouncer” problem that can be studied experimentally. It could provide a promising tool for studying fundamental neutron-matter interactions, as well as quantum neutron optics and surface physics effects. We develop a formalism that describes quantitatively the neutron motion near the mirror surface. The effects of mirror roughness are taken into account.

  20. Cavitation Effects in Centrifugal Pumps- A Review

    Directory of Open Access Journals (Sweden)

    Maxime Binama

    2016-05-01

    Full Text Available Cavitation is one of the most challenging fluid flow abnormalities leading to detrimental effects on both the centrifugal pump flow behaviors and physical characteristics. Centrifugal pumps’ most low pressure zones are the first cavitation victims, where cavitation manifests itself in form of pitting on the pump internal solid walls, accompanied by noise and vibration, all leading to the pump hydraulic performance degradation. In the present article, a general description of centrifugal pump performance and related parameters is presented. Based on the literature survey, some light were shed on fundamental cavitation features; where different aspects relating to cavitation in centrifugal pumps were briefly discussed

  1. Centrifugal separators and related devices and methods

    Science.gov (United States)

    Meikrantz, David H.; Law, Jack D.; Garn, Troy G.; Macaluso, Lawrence L.; Todd, Terry A.

    2012-03-06

    Centrifugal separators and related methods and devices are described. More particularly, centrifugal separators comprising a first fluid supply fitting configured to deliver fluid into a longitudinal fluid passage of a rotor shaft and a second fluid supply fitting sized and configured to sealingly couple with the first fluid supply fitting are described. Also, centrifugal separator systems comprising a manifold having a drain fitting and a cleaning fluid supply fitting are described, wherein the manifold is coupled to a movable member of a support assembly. Additionally, methods of cleaning centrifugal separators are described.

  2. Virgin Coconut Oil Production by Centrifugation Method

    OpenAIRE

    2014-01-01

    The virgin coconut oil (VCO) production by centrifugation method was studied. The production of VCO was studied by using various centrifugation speed, temperature and time intervals. The results showed that the yield of VCO was 13.53% at 12000rpm, at 120 minutes. The highest yield of VCO was 13.80% at centrifugation temperature of 40oC. The concentration of lauric acid present in the samples with variables of centrifugation temperatures, speed, and time intervals were 0.4543µg, 6.2367µg, and ...

  3. Virgin Coconut Oil Production by Centrifugation Method

    Directory of Open Access Journals (Sweden)

    Y.C.Wong

    2014-03-01

    Full Text Available The virgin coconut oil (VCO production by centrifugation method was studied. The production of VCO was studied by using various centrifugation speed, temperature and time intervals. The results showed that the yield of VCO was 13.53% at 12000rpm, at 120 minutes. The highest yield of VCO was 13.80% at centrifugation temperature of 40oC. The concentration of lauric acid present in the samples with variables of centrifugation temperatures, speed, and time intervals were 0.4543µg, 6.2367µg, and 6.4894µg respectively.

  4. Applying Chromatography.

    Science.gov (United States)

    Klein, Jessie W.; Patev, Paul

    1998-01-01

    Presents three experiments to introduce students to different kinds of chromatography: (1) paper chromatography; (2) gel filtration chromatography; and (3) reverse-phase liquid chromatography. Written in the form of a laboratory manual, explanations of each of the techniques, materials needed, procedures, and a glossary are included. (PVD)

  5. Immiscible silicate liquid partition coefficients: implications for crystal-melt element partitioning and basalt petrogenesis

    Science.gov (United States)

    Veksler, Ilya V.; Dorfman, Alexander M.; Danyushevsky, Leonid V.; Jakobsen, Jakob K.; Dingwell, Donald B.

    2006-12-01

    This study investigates partitioning of elements between immiscible aluminosilicate and borosilicate liquids using three synthetic mixtures doped with 32 trace elements. In order to get a good spatial separation of immiscible liquids, we employed a high-temperature centrifuge. Experiments were performed at 1,050-1,150°C, 1 atm, in sealed Fe and Pt containers. Quenched products were analysed by electron microprobe and LA ICP-MS. Nernst partition coefficients ( D’s) between the Fe-rich and Si-rich aluminosilicate immiscible liquids are the highest for Zn (3.3) and Fe (2.6) and the lowest for Rb and K (0.4-0.5). The plots of D values against ionic potential Z/r in all the compositions show a convex upward trend, which is typical also for element partitioning between immiscible silicate and salt melts. The results bear upon the speciation and structural position of elements in multicomponent silicate liquids. The ferrobasalt-rhyolite liquid immiscibility is observed in evolved basaltic magmas, and may play an important role in large gabbroic intrusions, such as Skaergaard, and during the generation of unusual lavas, such as ferropicrites.

  6. Partition density functional theory

    Science.gov (United States)

    Nafziger, Jonathan

    Partition density functional theory (PDFT) is a method for dividing a molecular electronic structure calculation into fragment calculations. The molecular density and energy corresponding to Kohn Sham density-functional theory (KS-DFT) may be exactly recovered from these fragments. Each fragment acts as an isolated system except for the influence of a global one-body 'partition' potential which deforms the fragment densities. In this work, the developments of PDFT are put into the context of other fragment-based density functional methods. We developed three numerical implementations of PDFT: One within the NWChem computational chemistry package using basis sets, and the other two developed from scratch using real-space grids. It is shown that all three of these programs can exactly reproduce a KS-DFT calculation via fragment calculations. The first of our in-house codes handles non-interacting electrons in arbitrary one-dimensional potentials with any number of fragments. This code is used to explore how the exact partition potential changes for different partitionings of the same system and also to study features which determine which systems yield non-integer PDFT occupations and which systems are locked into integer PDFT occupations. The second in-house code, CADMium, performs real-space calculations of diatomic molecules. Features of the exact partition potential are studied for a variety of cases and an analytical formula determining singularities in the partition potential is derived. We introduce an approximation for the non-additive kinetic energy and show how this quantity can be computed exactly. Finally a PDFT functional is developed to address the issues of static correlation and delocalization errors in approximations within DFT. The functional is applied to the dissociation of H2 + and H2.

  7. Design Attributes and Scale Up Testing of Annular Centrifugal Contactors

    Energy Technology Data Exchange (ETDEWEB)

    David H. Meikrantz; Jack D. Law

    2005-04-01

    Annular centrifugal contactors are being used for rapid yet efficient liquid- liquid processing in numerous industrial and government applications. Commercialization of this technology began eleven years ago and now units with throughputs ranging from 0.25 to 700 liters per minute are readily available. Separation, washing, and extraction processes all benefit from the use of this relatively new commercial tool. Processing advantages of this technology include: low in-process volume per stage, rapid mixing and separation in a single unit, connection-in-series for multi-stage use, and a wide operating range of input flow rates and phase ratios without adjustment. Recent design enhancements have been added to simplify maintenance, improve inspection ability, and provide increased reliability. Cartridge-style bearing and mechanical rotary seal assemblies that can include liquid-leak sensors are employed to enhance remote operations, minimize maintenance downtime, prevent equipment damage, and extend service life. Clean-in-place capability eliminates the need for disassembly, facilitates the use of contactors for feed clarification, and can be automated for continuous operation. In nuclear fuel cycle studies, aqueous based separations are being developed that efficiently partition uranium, actinides, and fission products via liquid-liquid solvent extraction. Thus, annular centrifugal contactors are destined to play a significant role in the design of such new processes. Laboratory scale studies using mini-contactors have demonstrated feasibility for many such separation processes but validation at an engineering scale is needed to support actual process design.

  8. Matrix string partition function

    CERN Document Server

    Kostov, Ivan K; Kostov, Ivan K.; Vanhove, Pierre

    1998-01-01

    We evaluate quasiclassically the Ramond partition function of Euclidean D=10 U(N) super Yang-Mills theory reduced to a two-dimensional torus. The result can be interpreted in terms of free strings wrapping the space-time torus, as expected from the point of view of Matrix string theory. We demonstrate that, when extrapolated to the ultraviolet limit (small area of the torus), the quasiclassical expressions reproduce exactly the recently obtained expression for the partition of the completely reduced SYM theory, including the overall numerical factor. This is an evidence that our quasiclassical calculation might be exact.

  9. Distributed Evolutionary Graph Partitioning

    CERN Document Server

    Sanders, Peter

    2011-01-01

    We present a novel distributed evolutionary algorithm, KaFFPaE, to solve the Graph Partitioning Problem, which makes use of KaFFPa (Karlsruhe Fast Flow Partitioner). The use of our multilevel graph partitioner KaFFPa provides new effective crossover and mutation operators. By combining these with a scalable communication protocol we obtain a system that is able to improve the best known partitioning results for many inputs in a very short amount of time. For example, in Walshaw's well known benchmark tables we are able to improve or recompute 76% of entries for the tables with 1%, 3% and 5% imbalance.

  10. Centrifuge modelling of offshore monopile foundation

    DEFF Research Database (Denmark)

    Klinkvort, Rasmus Tofte; Hededal, Ole

    2010-01-01

    centrifuge tests on a laterally loaded monopile in dry sand. The prototype dimension of the piles was modelled to a diameter of 1 meter and penetration depth on 6 meter. The test series were designed in order to investigate the scaling laws in the centrifuge both for monotonic and cyclic loading...

  11. Centrifugal innervation of the mammalian olfactory bulb.

    Science.gov (United States)

    Matsutani, Shinji; Yamamoto, Noboru

    2008-12-01

    Although it has been known for decades that the mammalian olfactory bulb receives a substantial number of centrifugal inputs from other regions of the brain, relatively few data have been available on the function of the centrifugal olfactory system. Knowing the role of the centrifugal projection and how it works is of critical importance to fully understanding olfaction. The centrifugal fibers can be classified into two groups, a group that release neuromodulators, such as noradrenaline, serotonin, or acetylcholine, and a group originating in the olfactory cortex. Accumulating evidence suggests that centrifugal neuromodulatory inputs are associated with acquisition of odor memory. Because the distribution of the terminals on these fibers is diffuse and widespread, the neuromodulatory inputs must affect diverse subsets of bulbar neurons at the same time. In contrast, knowledge of the role of centrifugal fibers from the olfactory cortical areas is limited. Judging from recent morphological evidence, these fibers may modify the activity of neurons located in sparse and discrete loci in the olfactory bulb. Given the modular organization of the olfactory bulb, centrifugal fibers from the olfactory cortex may help coordinate the activities of restricted subsets of neurons belonging to distinct functional modules in an odor-specific manner. Because the olfactory cortex receives inputs from limbic and neocortical areas in addition to inputs from the bulb, the centrifugal inputs from the cortex can modulate odor processing in the bulb in response to non-olfactory as well as olfactory cues.

  12. Rotor for a pyrolysis centrifuge reactor

    DEFF Research Database (Denmark)

    2015-01-01

    The present invention relates to a rotor for a pyrolysis centrifuge reactor, said rotor comprising a rotor body having a longitudinal centre axis, and at least one pivotally mounted blade being adapted to pivot around a pivot axis under rotation of the rotor body around the longitudinal centre axis....... Moreover, the present invention relates to a pyrolysis centrifuge reactor applying such a rotor....

  13. Partitions with Initial Repetitions

    Institute of Scientific and Technical Information of China (English)

    George E. ANDREWS

    2009-01-01

    A variety of interesting connections with modular forms, mock theta functions and Rogers-Ramanujan type identities arise in consideration of partitions in which the smaller integers are repeated as summands more often than the larger summands. In particular, this concept leads to new interpre-tations of the Rogers-Selberg identities and Bailey's modulus 9 identities.

  14. New Aperture Partitioning Element

    Science.gov (United States)

    Griffin, S.; Calef, B.; Williams, S.

    Postprocessing in an optical system can be aided by adding an optical element to partition the pupil into a number of segments. When imaging through the atmosphere, the recorded data are blurred by temperature-induced variations in the index of refraction along the line of sight. Using speckle imaging techniques developed in the astronomy community, this blurring can be corrected to some degree. The effectiveness of these techniques is diminished by redundant baselines in the pupil. Partitioning the pupil reduces the degree of baseline redundancy, and therefore improves the quality of images that can be obtained from the system. It is possible to implement the described approach on an optical system with a segmented primary mirror, but not very practical. This is because most optical systems do not have segmented primary mirrors, and those that do have relatively low bandwidth positioning of segments due to their large mass and inertia. It is much more practical to position an active aperture partitioning element at an aft optics pupil of the optical system. This paper describes the design, implementation and testing of a new aperture partitioning element that is completely reflective and reconfigurable. The device uses four independent, annular segments that can be positioned with a high degree of accuracy without impacting optical wavefront of each segment. This mirror has been produced and is currently deployed and working on the 3.6 m telescope.

  15. Centrifugal membrane filtration -- Task 9

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-08-01

    The Energy and Environmental Research Center (EERC) has teamed with SpinTek Membrane Systems, Inc., the developer of a centrifugal membrane filtration technology, to demonstrate applications for the SpinTek technology within the US Department of Energy (DOE) Environmental management (EM) Program. The technology uses supported microporous membranes rotating at high rpm, under pressure, to separate suspended and colloidal solids from liquid streams, yielding a solids-free permeate stream and a highly concentrated solids stream. This is a crosscutting technology that falls under the Efficient Separations and Processing Crosscutting Program, with potential application to tank wastes, contaminated groundwater, landfill leachate, and secondary liquid waste streams from other remediation processes, including decontamination and decommissioning systems. Membrane-screening tests were performed with the SpinTek STC-X4 static test cell filtration unit, using five ceramic membranes with different pore size and composition. Based on permeate flux, a 0.25-{micro}m TiO{sub 2}/Al{sub 2}O{sub 3} membrane was selected for detailed performance evaluation using the SpinTek ST-IIL centrifugal membrane filtration unit with a surrogate tank waste solution. An extended test run of 100 hr performed on a surrogate tank waste solution showed some deterioration in filtration performance, based on flux, apparently due to the buildup of solids near the inner portion of the membrane where relative membrane velocities were low. Continued testing of the system will focus on modifications to the shear pattern across the entire membrane surface to affect improved long-term performance.

  16. On partitions avoiding right crossings

    CERN Document Server

    Yan, Sherry H F

    2011-01-01

    Recently, Chen et al. derived the generating function for partitions avoiding right nestings and posed the problem of finding the generating function for partitions avoiding right crossings. In this paper, we derive the generating function for partitions avoiding right crossings via an intermediate structure of partial matchings avoiding 2-right crossings and right nestings. We show that there is a bijection between partial matchings avoiding 2-right crossing and right nestings and partitions avoiding right crossings.

  17. Centrifuge workers study. Phase II, completion report

    Energy Technology Data Exchange (ETDEWEB)

    Wooten, H.D.

    1994-09-01

    Phase II of the Centrifuge Workers Study was a follow-up to the Phase I efforts. The Phase I results had indicated a higher risk than expected among centrifuge workers for developing bladder cancer when compared with the risk in the general population for developing this same type of cancer. However, no specific agent could be identified as the causative agent for these bladder cancers. As the Phase II Report states, Phase I had been limited to workers who had the greatest potential for exposure to substances used in the centrifuge process. Phase II was designed to expand the survey to evaluate the health of all employees who had ever worked in Centrifuge Program Departments 1330-1339 but who had not been interviewed in Phase I. Employees in analytical laboratories and maintenance departments who provided support services for the Centrifuge Program were also included in Phase II. In December 1989, the Oak Ridge Associated Universities (ORAU), now known as Oak Ridge Institute for Science and Education (ORISE), was contracted to conduct a follow-up study (Phase II). Phase H of the Centrifuge Workers Study expanded the survey to include all former centrifuge workers who were not included in Phase I. ORISE was chosen because they had performed the Phase I tasks and summarized the corresponding survey data therefrom.

  18. The Fibonacci partition triangles

    CERN Document Server

    Fahr, Philipp

    2011-01-01

    In two previous papers we have presented partition formulae for the Fibonacci numbers motivated by the appearance of the Fibonacci numbers in the representation theory of the 3-Kronecker quiver and its universal cover, the 3-regular tree. Here we show that the basic information can be rearranged in two triangles. They are quite similar to the Pascal triangle of the binomial coefficients, but in contrast to the additivity rule for the Pascal triangle, we now deal with additivity along hooks, or, equivalently, with additive functions for valued translation quivers. As for the Pascal triangle, we see that the numbers in these Fibonacci partition triangles are given by evaluating polynomials. We show that the two triangles can be obtained from each other by looking at differences of numbers, it is sufficient to take differences along arrows and knight's moves.

  19. Partitional clustering algorithms

    CERN Document Server

    2015-01-01

    This book summarizes the state-of-the-art in partitional clustering. Clustering, the unsupervised classification of patterns into groups, is one of the most important tasks in exploratory data analysis. Primary goals of clustering include gaining insight into, classifying, and compressing data. Clustering has a long and rich history that spans a variety of scientific disciplines including anthropology, biology, medicine, psychology, statistics, mathematics, engineering, and computer science. As a result, numerous clustering algorithms have been proposed since the early 1950s. Among these algorithms, partitional (nonhierarchical) ones have found many applications, especially in engineering and computer science. This book provides coverage of consensus clustering, constrained clustering, large scale and/or high dimensional clustering, cluster validity, cluster visualization, and applications of clustering. Examines clustering as it applies to large and/or high-dimensional data sets commonly encountered in reali...

  20. BKP plane partitions

    Energy Technology Data Exchange (ETDEWEB)

    Foda, Omar; Wheeler, Michael [Department of Mathematics and Statistics, University of Melbourne, Parkville, Victoria 3010 (Australia)

    2007-01-15

    Using BKP neutral fermions, we derive a product expression for the generating function of volume-weighted plane partitions that satisfy two conditions. If we call a set of adjacent equal height-h columns, h > 0, an h-path, then 1. Every h-path can assume one of two possible colours. 2. There is a unique way to move along an h-path from any column to another.

  1. Generalised twisted partition functions

    CERN Document Server

    Petkova, V B

    2001-01-01

    We consider the set of partition functions that result from the insertion of twist operators compatible with conformal invariance in a given 2D Conformal Field Theory (CFT). A consistency equation, which gives a classification of twists, is written and solved in particular cases. This generalises old results on twisted torus boundary conditions, gives a physical interpretation of Ocneanu's algebraic construction, and might offer a new route to the study of properties of CFT.

  2. Gas dynamics in strong centrifugal fields

    Energy Technology Data Exchange (ETDEWEB)

    Bogovalov, S.V.; Kislov, V.A.; Tronin, I.V. [National research nuclear university “MEPhI”, Kashirskoje shosse, 31,115409, Moscow (Russian Federation)

    2015-03-10

    Dynamics of waves generated by scopes in gas centrifuges (GC) for isotope separation is considered. The centrifugal acceleration in the GC reaches values of the order of 106g. The centrifugal and Coriolis forces modify essentially the conventional sound waves. Three families of the waves with different polarisation and dispersion exist in these conditions. Dynamics of the flow in the model GC Iguasu is investigated numerically. Comparison of the results of the numerical modelling of the wave dynamics with the analytical predictions is performed. New phenomena of the resonances in the GC is found. The resonances occur for the waves polarized along the rotational axis having the smallest dumping due to the viscosity.

  3. Dewatering of fine coal using hyperbaric centrifugation

    Energy Technology Data Exchange (ETDEWEB)

    Ramazan Asmatulu; Gerald H. Luttrell; Roe-Hoan Yoon [Virginia Polytechnic Institute and State University, Blacksburg, VA (US). Center for Advanced Separation Technologies

    2005-09-01

    Many coal preparation plants are forced to discard their fine coal because of the inability of existing technologies to reduce the moisture content of this product to an acceptable level. In an effort to overcome this problem, a new mechanical dewatering method has been developed that combines centrifugation with pressure filtration. The process, which may be referred to as hyperbaric centrifugation, is capable of producing a drier product than can be achieved using either filtration or centrifugation alone. The test data obtained from batch experiments show that the new method can reduce cake moisture to 10% or below for many fine coal product streams.

  4. Comparison of lipid membrane-water partitioning with various organic solvent-water partitions of neutral species and ionic species: Uniqueness of cerasome as a model for the stratum corneum in partition processes.

    Science.gov (United States)

    Zhang, Keda; Fahr, Alfred; Abraham, Michael H; Acree, William E; Tobin, Desmond J; Liu, Xiangli

    2015-10-15

    Lipid membrane-water partitions (e.g., immobilized artificial membrane systems where the lipid membrane is a neutral phospholipid monolayer bound to gel beads) were compared to various organic solvent-water partitions using linear free energy relationships. To this end, we also measured the retention factors of 36 compounds (including neutral and ionic species) from water to liposomes made up of 3-sn-phosphatidylcholine and 3-sn-phosphatidyl-l-serine (80:20, mol/mol), employing liposome electrokinetic chromatography in this work. The results show that lipid membranes exhibit a considerably different chemical environment from those of organic solvents. For both neutral species and ionic species, partitions into the more polar hydroxylic solvents are chemically closer to partition into the lipid membrane as compared to partitions into the less polar hydroxylic solvents and into aprotic solvents. This means that solutes partition into the polar parts of lipid membranes, regardless of whether they are charged or not. In addition, cerasome (i.e., liposome composed mainly of stratum corneum lipids) was compared with regular phospholipid liposomes as a possible model for human stratum corneum in partitions. It was found that the cerasome-water partition exhibits a better chemical similarity to skin permeation. This is probably due to the unique structures of ceramides that occur in cerasome and in the stratum corneum lipid domain. We further show that membranes in membrane-water partitions exhibit very different properties.

  5. Modeling of Centrifugal Force Field and the Effect on Filling and Solidification in Centrifugal Casting

    Science.gov (United States)

    Sheng, Wenbin; Ma, Chunxue; Gu, Wanli

    2011-06-01

    Based on the steady flow in a tube, a mathematical model has been established for the consideration of centrifuging force field by combining the equations of continuity, conservation of momentum and general energy. Effects of centrifugal field on the filling and solidification are modeled by two accessional terms: centrifugal force and Chorios force. In addition, the transfer of heat by convection is considered to achieve a coupling calculation of velocity field and temperature field. The solution of pressure item is avoided by introducing the stream function ψ(x,y) and the eddy function ξ(x,y). Corresponding difference formats for the simultaneous equations of centrifugal filling, the accessional terms and the solidifying latent heat have been established by the finite difference technique. Furthermore, the centrifugal filling and solidification processes in a horizontal tube are summarized to interpret the mechanism by which internal defects are formed in centrifugal castings.

  6. Deburring by centrifugal barrel tumbling

    Energy Technology Data Exchange (ETDEWEB)

    Gillespie, L.K.

    1976-08-01

    The reliability of small precision mechanisms greatly depends upon the production of burr-free, sharp-edged parts. Centrifugal barrel finishing (Harperizing) is one of the few processes capable of producing these conditions. Burrs less than 0.001-in. thick by 0.001-in. high (25.4 x 25.4 ..mu..m) can be removed from 303 Se stainless steel, 1018 steel, and 6061-T6 aluminum with dimensional changes in the order of 0.0001-in. (2.54 ..mu..m) and final edge radii of 0.003 in. (76.2 ..mu..m). These conditions can be produced in batch lots in 20 minutes or less. Surface finishes can be reduced from 45 to 25 or 35 microinches (1.15 to 0.68 or 0.89 ..mu..m), with 60-minute cycle times. Stock losses appear to be repeatable within +-0.00006 in. (1.524 ..mu..m). Very small parts receive less action than parts 0.5 in. (12.7 mm) in dia.

  7. Molecular structure and centrifugal distortion in methylthioethyne

    NARCIS (Netherlands)

    Engelsen, D. den

    1969-01-01

    The investigation of the microwave spectra of five isotopic species of methylthioethyne, HCCSCH3 enabled a fairly reliable calculation to be made of bond lengths and angles. The centrifugal distortion parameters are related to molecular vibrations.

  8. Geotechnical Centrifuge Studies of Unsaturated Transport

    Science.gov (United States)

    Smith, R. W.; Mattson, E. D.; Palmer, C. D.

    2007-12-01

    Improved understanding of contaminant migration in heterogeneous, variably saturated porous media is required to better define the long-term stewardship requirements for U.S. Department of Energy (DOE) lands and to assist in the design of effective vadose-zone barriers to contaminant migrations. A geotechnical centrifuge provides an experimental approach to explore vadose zone transport over a wide range of relevant conditions in time frames not possible for conventional bench-top experiments. Our research to date resulted in the design, construction, and testing of in-flight experimental apparatus allowing the replication of traditional bench top unsaturated transport experiments using the 2-meter radius geotechnical centrifuge capabilities at the Idaho National Laboratory. Additionally we conducted a series of unsaturated 1-dimenstional column experiments using conservative tracers to evaluate the effects of increased centrifugal acceleration on derived transport properties and assessing the scaling relationships for these properties. Our experimental results indicated that breakthrough times for a conservative tracer decreased significantly and systematically as a function of increased centrifugal acceleration. Differences between these experimental results and estimates based on predictive scaling rules are due to slight moisture content differences between experiments at different centrifugal accelerations. In contrast, dispersion coefficients varied systemically with centrifugal acceleration in accordance with predictive scaling rules. The results we obtained in this study indicate that the centrifuge technique is a viable experimental method for the study of subsurface processes where gravitational acceleration is important. The geotechnical centrifuge allows experiments to be completed more quickly than tests conducted at 1-gravity and can be used to experimentally address important scaling issues, and permits experiments under a range of conditions that

  9. Combination Of Investment And Centrifugal Casting

    Science.gov (United States)

    Creeger, Gordon A.

    1994-01-01

    Modifications, including incorporation of centrifugal casting, made in investment-casting process reducing scrap rate. Used to make first- and second-stage high-pressure-fuel-turbopump nozzles, containing vanes with thin trailing edges and other thin sections. Investment mold spun for short time while being filled, and stopped before solidification occurs. Centrifugal force drives molten metal into thin trailing edges, ensuring they are filled. With improved filling, preheat and pour temperatures reduced and solidification hastened so less hot tearing.

  10. Clinical experience with the Sarns centrifugal pump.

    Science.gov (United States)

    Curtis, J J; Walls, J T; Demmy, T L; Boley, T M; Schmaltz, R A; Goss, C F; Wagner-Mann, C C

    1993-07-01

    Since October 1986, we have had experience with 96 Sarns centrifugal pumps in 72 patients (pts). Heparinless left atrial to femoral artery or aorta bypass was used in 14 pts undergoing surgery on the thoracic aorta with 13 survivors (93%). No paraplegia or device-related complications were observed. In 57 patients, the Sarns centrifugal pump was used as a univentricular (27 pts) or biventricular (30 pts) cardiac assist device for postcardiotomy cardiogenic shock. In these patients, cardiac assist duration ranged from 2 to 434 h with a hospital survival rate of 29% in those requiring left ventricular assist and 13% in those requiring biventricular assist. Although complications were ubiquitous in this mortally ill patient population, in 5,235 pump-hours, no pump thrombosis was observed. Hospital survivors followed for 4 months to 6 years have enjoyed an improved functional class. We conclude that the Sarns centrifugal pump is an effective cardiac assist device when used to salvage patients otherwise unweanable from cardiopulmonary bypass. Partial left ventricular bypass using a centrifugal pump has become our procedure of choice for unloading the left ventricle and for maintenance of distal aortic perfusion pressure when performing surgery on the thoracic aorta. This clinical experience with the Sarns centrifugal pump appears to be similar to that reported with other centrifugal assist devices.

  11. A general method to study equilibrium partitioning of macromolecules

    DEFF Research Database (Denmark)

    The distribution of macromolecules between a confined microscopic solution and a macroscopic bulk solution plays an important role in understanding separation processes such as Size Exclusion Chromatography (SEC). In this study, we have developed an efficient computational algorithm for obtaining...... of this dimension rather than Rg (radius of gyration) or Rh (hydrodynamic radius) gives a better universality in the plot of the partition coefficient as a function of the chain dimension relative to the pore size....

  12. Partitioning the Quaternary

    Science.gov (United States)

    Gibbard, Philip L.; Lewin, John

    2016-11-01

    We review the historical purposes and procedures for stratigraphical division and naming within the Quaternary, and summarize the current requirements for formal partitioning through the International Commission on Stratigraphy (ICS). A raft of new data and evidence has impacted traditional approaches: quasi-continuous records from ocean sediments and ice cores, new numerical dating techniques, and alternative macro-models, such as those provided through Sequence Stratigraphy and Earth-System Science. The practical usefulness of division remains, but there is now greater appreciation of complex Quaternary detail and the modelling of time continua, the latter also extending into the future. There are problems both of commission (what is done, but could be done better) and of omission (what gets left out) in partitioning the Quaternary. These include the challenge set by the use of unconformities as stage boundaries, how to deal with multiphase records in ocean and terrestrial sediments, what happened at the 'Early-Mid- (Middle) Pleistocene Transition', dealing with trends that cross phase boundaries, and the current controversial focus on how to subdivide the Holocene and formally define an 'Anthropocene'.

  13. Measurement and analysis of the mannitol partition coefficient in sucrose crystallization under simulated industrial conditions.

    Science.gov (United States)

    Eggleston, Gillian; Yen, Jenny Wu Tiu; Alexander, Clay; Gober, Jessica

    2012-07-01

    Mannitol is a major deterioration product of Leuconstoc mesenteroides bacterial metabolism of sucrose and fructose from both sugarcane and sugar beet. The effect of crystallization conditions on the mannitol partition coefficient (K(eff)) between impure sucrose syrup and crystal has been investigated in a batch laboratory crystallizer and a batch pilot plant-scale vacuum pan. Laboratory crystallization was operated at 65.5°C (150°F), 60.0°C (140°F), and 51.7°C (125°F) with a 78.0 Brix (% refractometric dissolved solids) pure sucrose syrup containing 0%, 0.1%, 0.2%, 1.0%, 2.0%, 3.0%, and 10% (at 65.5°C only) mannitol on a Brix basis. Produced mother liquor and crystals were separated by centrifugation and their mannitol contents measured by ion chromatography with integrated pulsed amperometric detection (IC-IPAD). The extent of mannitol partitioning into the crystals depended strongly on the mannitol concentration in the feed syrup and, to a lesser extent, the crystallization temperature. At 65.5 and 60.0°C, the K(eff) varied from ~0.4% to 3.0% with 0.2% to 3.0% mannitol in the feed syrup, respectively. The mannitol K(eff) was lower than that reported for dextran (~9-10% K(eff)), another product of Leuconstoc deterioration, under similar sucrose crystal growth conditions. At 10% mannitol concentration in the syrup at 65.5°C, co-crystallization of mannitol with sucrose occurred and the crystal growth rate was greatly impeded. In both laboratory and pilot plant crystallizations (95.7% purity; 78.0 Brix; 65.5°C), mannitol tended to cause conglomerates to form, which became progressively worse with increased mannitol syrup concentration. At the 3% mannitol concentration, crystallization at both the laboratory and pilot plant scales was more difficult. Mannitol incorporation into the sucrose crystal results mostly from liquid syrup inclusions but adsorption onto the crystal surface may play a minor role at lower mannitol concentrations.

  14. Fast Pyrolysis of Lignin Using a Pyrolysis Centrifuge Reactor

    DEFF Research Database (Denmark)

    Trinh, Ngoc Trung; Jensen, Peter Arendt; Sárossy, Zsuzsa

    2013-01-01

    Fast pyrolysis of lignin from an ethanol plant was investigated on a lab scale pyrolysis centrifuge reactor (PCR) with respect to pyrolysis temperature, reactor gas residence time, and feed rate. A maximal organic oil yield of 34 wt % dry basis (db) (bio-oil yield of 43 wt % db) is obtained...... at temperatures of 500−550 °C, reactor gas residence time of 0.8 s, and feed rate of 5.6 g/min. Gas chromatography mass spectrometry and size-exclusion chromatography were used to characterize the Chemical properties of the lignin oils. Acetic acid, levoglucosan, guaiacol, syringols, and p-vinylguaiacol are found...... to be major chemical components in the lignin oil. The maximal yields of 0.62, 0.67, and 0.38 wt % db were obtained for syringol, p-vinylguaiacol, and guaiacol, respectively. The reactor temperature effect was investigated in a range of 450−600 °C and has a considerable effect on the observed chemical...

  15. Centrifugal acceleration in the magnetotail lobes

    Directory of Open Access Journals (Sweden)

    H. Nilsson

    2010-02-01

    Full Text Available Combined Cluster EFW and EDI measurements have shown that cold ion outflow in the magnetospheric lobes dominates the hydrogen ion outflow from the Earth's atmosphere. The ions have too low kinetic energy to be measurable with particle instruments, at least for the typical spacecraft potential of a sunlit spacecraft in the tenuous lobe plasmas outside a few RE. The measurement technique yields both density and bulk velocity, which can be combined with magnetic field measurements to estimate the centrifugal acceleration experienced by these particles. We present a quantitative estimate of the centrifugal acceleration, and the velocity change with distance which we would expect due to centrifugal acceleration. It is found that the centrifugal acceleration is on average outward with an average value of about of 5 m s−2. This is small, but acting during long transport times and over long distances the cumulative effect is significant, while still consistent with the relatively low velocities estimated using the combination of EFW and EDI data. The centrifugal acceleration should accelerate any oxygen ions in the lobes to energies observable by particle spectrometers. The data set also put constraints on the effectiveness of any other acceleration mechanisms acting in the lobes, where the total velocity increase between 5 and 19 RE geocentric distance is less than 5 km s−1.

  16. A Review of Biomedical Centrifugal Microfluidic Platforms

    Directory of Open Access Journals (Sweden)

    Minghui Tang

    2016-02-01

    Full Text Available Centrifugal microfluidic or lab-on-a-disc platforms have many advantages over other microfluidic systems. These advantages include a minimal amount of instrumentation, the efficient removal of any disturbing bubbles or residual volumes, and inherently available density-based sample transportation and separation. Centrifugal microfluidic devices applied to biomedical analysis and point-of-care diagnostics have been extensively promoted recently. This paper presents an up-to-date overview of these devices. The development of biomedical centrifugal microfluidic platforms essentially covers two categories: (i unit operations that perform specific functionalities, and (ii systems that aim to address certain biomedical applications. With the aim to provide a comprehensive representation of current development in this field, this review summarizes progress in both categories. The advanced unit operations implemented for biological processing include mixing, valving, switching, metering and sequential loading. Depending on the type of sample to be used in the system, biomedical applications are classified into four groups: nucleic acid analysis, blood analysis, immunoassays, and other biomedical applications. Our overview of advanced unit operations also includes the basic concepts and mechanisms involved in centrifugal microfluidics, while on the other hand an outline on reported applications clarifies how an assembly of unit operations enables efficient implementation of various types of complex assays. Lastly, challenges and potential for future development of biomedical centrifugal microfluidic devices are discussed.

  17. India and Pakistan: Partition Lessons

    DEFF Research Database (Denmark)

    Kaur, Ravinder

    2007-01-01

    The violent territorial rupture of 1947 and its legacy reveal partition to be conceptually flawed and historically ill-grounded as a solution to political antagonism, says Ravinder Kaur.......The violent territorial rupture of 1947 and its legacy reveal partition to be conceptually flawed and historically ill-grounded as a solution to political antagonism, says Ravinder Kaur....

  18. Countercurrent chromatographic with upright multilayer coil plante centrifuge for large-scale preparation%一种用于大容量逆流色谱制备的立式多层螺旋管行星式离心机

    Institute of Scientific and Technical Information of China (English)

    吴世华; 孙翠荣; 戴元柏; 周慧; 潘远江; 张虹

    2003-01-01

    Owing to no complications caused by solid supports, such as adsorptive sample loss and deactivation, tailing of solute peaks, and contamination, countercurrent chromatography (CCC) has been an area of intense research since the first introduction of CCC in 1970,[1] and various apparatus and broad applications have been advanced[2,3]. For these developments, the type-J synchronous planet centrifuge has received considerable attention, which relies not only on its relatively simple mechanic design, but also on its high partition efficiency and short elution time caused by mixing and settling for the efficient chromatographic separations. In the past, however, almost all of type-J centrifuges rotated slowly were disposed horizontally due to the original design and some experiments that gravis plays an important role at a low rotary speed as similar to type-V rotating multilayer helical tube in unit gravity[4-9]. In fact,we discovered that the upright apparatus holds more retention of stationary phase than the horiziontal aparatus when large standard tubings were used as mutilayer coil column and the aparatus was operated under same contions. We report here a new coil planet centrifuge with four upright cylindrical columns for large scale countercurrent chromatographic preparation. The design principle and apparatus of UCCC is as samilar to type-J multilayer coil planet centrifuge. Four uptight cylindrical column holders are symmetrically arranged around the centrifuge axis as similar to the type-J HSCCC with three horizontal multilayer coils connected in series[8] . A series of experiments indicat that upright CCC has many advantages over the horizontal CCC when using a large-bore tube as multilayer coil column for large scale countercurrent chromatographic separation.Upright CCC provide a versatile countercurrent chromatographic method for large-scale preparation from very crude sample. It has good preparative capacity and flexible suitability to various sample and

  19. Analysis of Secondary Flows in Centrifugal Impellers

    Directory of Open Access Journals (Sweden)

    Brun Klaus

    2005-01-01

    Full Text Available Secondary flows are undesirable in centrifugal compressors as they are a direct cause for flow (head losses, create nonuniform meridional flow profiles, potentially induce flow separation/stall, and contribute to impeller flow slip; that is, secondary flows negatively affect the compressor performance. A model based on the vorticity equation for a rotating system was developed to determine the streamwise vorticity from the normal and binormal vorticity components (which are known from the meridional flow profile. Using the streamwise vorticity results and the small shear-large disturbance flow method, the onset, direction, and magnitude of circulatory secondary flows in a shrouded centrifugal impeller can be predicted. This model is also used to estimate head losses due to secondary flows in a centrifugal flow impeller. The described method can be employed early in the design process to develop impeller flow shapes that intrinsically reduce secondary flows rather than using disruptive elements such as splitter vanes to accomplish this task.

  20. Possible segregation caused by centrifugal titanium casting.

    Science.gov (United States)

    Watanabe, K; Okawa, S; Kanatani, M; Nakano, S; Miyakawa, O; Kobayashi, M

    1996-12-01

    The possibility of the segregation under solidification process using a centrifugal casting machine was investigated using an electron probe microanalyzer with elemental distribution map, line analysis and quantitative analysis. When a very small quantity of platinum was added to local molten titanium during the casting process, macroscopic segregation was observed under conditions of density difference of 0.1 g/cm3 at the most, confirming that the centrifugal force of the casting machine is extremely strong. When a Ti-6Al-4V alloy was cast, however, no macroscopic segregation was observed. The centrifugal force of the casting machine examined in the present study hardly results in the body-force segregation in this titanium alloy.

  1. Detection methods for centrifugal microfluidic platforms

    DEFF Research Database (Denmark)

    Burger, Robert; Amato, Letizia; Boisen, Anja

    2016-01-01

    Centrifugal microfluidics has attracted much interest from academia as well as industry, since it potentially offers solutions for affordable, user-friendly and portable biosensing. A wide range of so-called fluidic unit operations, e.g. mixing, metering, liquid routing, and particle separation......, have been developed and allow automation and integration of complex assay protocols in lab-on-a-disc systems. Besides liquid handling, the detection strategy for reading out the assay is crucial for developing a fully integrated system. In this review, we focus on biosensors and readout methods...... for the centrifugal microfluidics platform and cover optical as well as mechanical and electrical detection principles....

  2. Enhancing radiolytic stability upon concentration of tritium-labeled pharmaceuticals utilizing centrifugal evaporation.

    Science.gov (United States)

    Marques, Rosemary; Helmy, Roy; Waterhouse, David

    2015-05-30

    Tritium radiopharmaceuticals are often used in drug development because of their desirable specific activity. The inherent instability of these radioactive tracers often leads to a requirement to purify prior to use. Purification methodologies such as preparative chromatography and solid/liquid extractions often utilize water as a solvent, which is not suitable for long-term storage and necessitates removal. Rotary evaporation has traditionally been utilized for the removal of this unwanted solvent, however, this method has been shown to lead to decomposition of the tritium species in some cases. Centrifugal evaporation is a milder concentration method which has been demonstrated to effectively remove solvents. In this study, we show that centrifugal evaporation leads to effective concentration of tritium samples without the decomposition typically observed by rotary evaporation.

  3. A human gut metaproteomic dataset from stool samples pretreated or not by differential centrifugation

    Directory of Open Access Journals (Sweden)

    Alessandro Tanca

    2015-09-01

    Full Text Available We present a human gut metaproteomic dataset deposited in the ProteomeXchange Consortium via the PRIDE partner repository with the dataset identifier PXD001573. Ten aliquots of a single stool sample collected from a healthy human volunteer were either pretreated by differential centrifugation (DC; N=5 or not centrifuged (NC; N=5. Protein extracts were then processed by filter-aided sample preparation, single-run liquid chromatography and high-resolution mass spectrometry, and peptide identification was carried out using Sequest-HT as search engine within the Proteome Discoverer informatic platform. The dataset described here is also related to the research article entitled “Enrichment or depletion? The impact of stool pretreatment on metaproteomic characterization of the human gut microbiota” published in Proteomics (Tanca et al., 2015, [1].

  4. Instantons on ALE spaces and orbifold partitions

    Science.gov (United States)

    Dijkgraaf, Robbert; Sułkowski, Piotr

    2008-03-01

    We consider Script N = 4 theories on ALE spaces of Ak-1 type. As is well known, their partition functions coincide with Ak-1 affine characters. We show that these partition functions are equal to the generating functions of some peculiar classes of partitions which we introduce under the name 'orbifold partitions'. These orbifold partitions turn out to be related to the generalized Frobenius partitions introduced by G. E. Andrews some years ago. We relate the orbifold partitions to the blended partitions and interpret explicitly in terms of a free fermion system.

  5. Instantons on ALE spaces and orbifold partitions

    CERN Document Server

    Dijkgraaf, Robbert

    2008-01-01

    We consider N=4 theories on ALE spaces of $A_{k-1}$ type. As is well known, their partition functions coincide with $A_{k-1}$ affine characters. We show that these partition functions are equal to the generating functions of some peculiar classes of partitions which we introduce under the name 'orbifold partitions'. These orbifold partitions turn out to be related to the generalized Frobenius partitions introduced by G. E. Andrews some years ago. We relate the orbifold partitions to the blended partitions and interpret explicitly in terms of a free fermion system.

  6. Internal flow numerical simulation of double-suction centrifugal pump using DES model

    Science.gov (United States)

    Zhou, P. J.; Wang, F. J.; Yang, M.

    2012-11-01

    It is a challenging task for the flow simulation for a double-suction centrifugal pump, because the wall effects are strong in this type of pumps. Detached-eddy simulation (DES), referred as a hybrid RANS-LES approach, has emerged recently as a potential compromise between RANS based turbulence models and Large Eddy Simulation. In this approach, the unsteady RANS model is employed in the boundary layer, while the LES treatment is applied to the separated region. In this paper, S-A DES method and SST k-ω DES method are applied to the numerical simulation for the 3D flow in whole passage of a double-suction centrifugal pump. The unsteady flow field including velocity and pressure distributions is obtained. The head and efficiency of the pump are predicted and compared with experimental results. According to the calculated results, S-A DES model is easy to control the partition of the simulation when using near wall grid with 30 suction centrifugal pump. S-A DES method can capture more flow phenomenon than SST k - ω DES method. In addition, it can accurately predict the power performance under different flow conditions, and can reflect pressure fluctuation characteristics.

  7. Centrifugal Sieve for Size-Segregation/ Beneficiation of Regolith Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Utilizing centrifugal force as the primary body-force, combined with both shearing flow and vibratory motion the proposed centrifugal-sieve separators can provide...

  8. Partitioning ecosystems for sustainability.

    Science.gov (United States)

    Murray, Martyn G

    2016-03-01

    Decline in the abundance of renewable natural resources (RNRs) coupled with increasing demands of an expanding human population will greatly intensify competition for Earth's natural resources during this century, yet curiously, analytical approaches to the management of productive ecosystems (ecological theory of wildlife harvesting, tragedy of the commons, green economics, and bioeconomics) give only peripheral attention to the driving influence of competition on resource exploitation. Here, I apply resource competition theory (RCT) to the exploitation of RNRs and derive four general policies in support of their sustainable and equitable use: (1) regulate resource extraction technology to avoid damage to the resource base; (2) increase efficiency of resource use and reduce waste at every step in the resource supply chain and distribution network; (3) partition ecosystems with the harvesting niche as the basic organizing principle for sustainable management of natural resources by multiple users; and (4) increase negative feedback between consumer and resource to bring about long-term sustainable use. A simple policy framework demonstrates how RCT integrates with other elements of sustainability science to better manage productive ecosystems. Several problem areas of RNR management are discussed in the light of RCT, including tragedy of the commons, overharvesting, resource collapse, bycatch, single species quotas, and simplification of ecosystems.

  9. Centrifugal Pump Experiment for Chemical Engineering Undergraduates

    Science.gov (United States)

    Vanderslice, Nicholas; Oberto, Richard; Marrero, Thomas R.

    2012-01-01

    The purpose of this paper is to describe a Centrifugal Pump Experiment that provided an experiential learning experience to chemical engineering undergraduates at the University of Missouri in the spring of 2010 in the Unit Operations Laboratory course. Lab equipment was used by senior students with computer-based data and control technology. In…

  10. APPLICATION ANALYSIS REPORT: RETECH PLASMA CENTRIFUGAL FURNACE

    Science.gov (United States)

    This document is an evaluation of the performance of the Retech, Inc. Plasma Centrifugal Furnace (PCF) and its applicability as a treatment for soils contaminated with organic and/or inorganic compounds. Both the technical and economic aspectsof the technology were examined. A...

  11. Performance of a Centrifugal Slurry Pump

    Directory of Open Access Journals (Sweden)

    Hawas Yahya Bajawi

    2014-02-01

    Full Text Available The aim of this study was to experimentally investigate the effect of speed, concentration and size of slurry on the performance of a centrifugal pump. For this purpose a facility was built where the performance of a centrifugal slurry pump was examined using aggregate slurry. Three sizes of slurry with three concentrations and at three impeller speeds were used for the performance investigations of a centrifugal slurry pump. As a reference performance the performance of centrifugal slurry pump was also tested with clean water. The performance of pump has been reported as variations of head, power and efficiency at various flow rates along with the system characteristics of the pump. The results reveal that the pump performance is grossly affected by the type of slurry, its concentration and size. Besides this the variation in speed also affects the performance as is observed in pumps with water. The maximum decrease in the head, with respect to clear water, at the operating point was found to be 47% for aggregate for size 20 mm, 15% concentration and 2600 rpm. The maximum decrement in efficiency at operating point for aggregate was found to be 47% for 4 mm size, 15% concentration and at 2200 rpm. The power increment requirement for aggregate was 9% for 4 mm size, 15% concentration and 2600 rpm.

  12. Predicting Droplet Formation on Centrifugal Microfluidic Platforms

    Science.gov (United States)

    Moebius, Jacob Alfred

    Centrifugal microfluidics is a widely known research tool for biological sample and water quality analysis. Currently, the standard equipment used for such diagnostic applications include slow, bulky machines controlled by multiple operators. These machines can be condensed into a smaller, faster benchtop sample-to-answer system. Sample processing is an important step taken to extract, isolate, and convert biological factors, such as nucleic acids or proteins, from a raw sample to an analyzable solution. Volume definition is one such step. The focus of this thesis is the development of a model predicting monodispersed droplet formation and the application of droplets as a technique for volume definition. First, a background of droplet microfluidic platforms is presented, along with current biological analysis technologies and the advantages of integrating such technologies onto microfluidic platforms. Second, background and theories of centrifugal microfluidics is given, followed by theories relevant to droplet emulsions. Third, fabrication techniques for centrifugal microfluidic designs are discussed. Finally, the development of a model for predicting droplet formation on the centrifugal microfluidic platform are presented for the rest of the thesis. Predicting droplet formation analytically based on the volumetric flow rates of the continuous and dispersed phases, the ratios of these two flow rates, and the interfacial tension between the continuous and dispersed phases presented many challenges, which will be discussed in this work. Experimental validation was completed using continuous phase solutions of different interfacial tensions. To conclude, prospective applications are discussed with expected challenges.

  13. Centrifugal Casting of Tubular Perovskite Membranes

    NARCIS (Netherlands)

    Mertins, Frederic H.B.; Kruidhof, Henk; Bouwmeester, Henny J.M.

    2005-01-01

    Dense tubular membranes were produced by centrifugal casting of an aqueous suspension, containing powder particles of the mixed-conducting perovskite La0.5Sr0.5CoO3−δ and a dispersant. The resulting green bodies were dried and sintered to produce tubes with a maximum length of 12 cm, having a relat

  14. Evaluation of an improved centrifugal casting machine.

    Science.gov (United States)

    Donovan, T E; White, L E

    1985-05-01

    A Type III gold alloy, a silver-palladium alloy, and a base metal alloy were cast in two different centrifugal casting machines. With the number of complete cast mesh squares as an indicator of castability, the Airspin casting machine produced superior castings with all three alloys. The base metal alloy produced the greatest number of complete squares with both casting machines.

  15. Pressure distribution in centrifugal dental casting.

    Science.gov (United States)

    Nielsen, J P

    1978-02-01

    Equations are developed for liquid metal pressure in centrifugal dental casting, given the instantaneous rotational velocity, density, and certain dimensions of the casting machine and casting pattern. A "reference parabola" is introduced making the fluid pressure concept more understandable. A specially designed specimen demonstrates experimentally the reference parabola at freezing.

  16. Evolution of microstructure in centrifugal cast Al-Cu alloy

    Directory of Open Access Journals (Sweden)

    Sui Yanwei

    2010-02-01

    Full Text Available In this research, the effects of centrifugal radius and mould rotation speed on microstructure in centrifugal-cast Al-Cu alloy have been investigated. The results show that, with increase of the centrifugal radius or mould rotation speed, the grain size of centrifugal-cast Al-Cu alloy decreases gradually, while the content of white phases containing the Al2Cu precipitated from α-phase, divorced eutectic and regular eutectic microstructure increases, leading to higher Cu macrosegregation. The variation level of microstructure in centrifugal-cast Al-Cu alloy at 600 rpm of mould rotation speed is greater than that at 300 rpm.

  17. A Theoretical Study of the Separation Principle in Size Exclusion Chromatography

    DEFF Research Database (Denmark)

    Wang, Yanwei; Teraoka, Iwao; Hansen, Flemming Yssing

    2010-01-01

    The principle of polymer separation in size exclusion chromatography (SEC) is studied based on a classical equilibrium partitioning theory. The task is to examine the correlation between the mean span dimension of polymer chains and their equilibrium partition coefficients with confining pores...

  18. Gas chromatography

    Science.gov (United States)

    Guiochon, Georges; Guillemin, Claude L.

    1990-11-01

    Gas chromatography is a powerful separation technique for gas and vapor mixtures. Combining separation and on-line detection permits accurate quantitative analysis of complex mixtures, including traces of compounds down to parts per trillions in some particular cases. The importance of gas chromatography in quality control and process control in the chemical and drug industry, in environmental pollution investigations and in clinical analysis is critical. The principles of the technique are discussed, the main components of a gas chromatograph are described and some idea of the importance of the applications is given.

  19. Efficient FM Algorithm for VLSI Circuit Partitioning

    Directory of Open Access Journals (Sweden)

    M.RAJESH

    2013-04-01

    Full Text Available In FM algorithm initial partitioning matrix of the given circuit is assigned randomly, as a result for larger circuit having hundred or more nodes will take long time to arrive at the final partition if theinitial partitioning matrix is close to the final partitioning then the computation time (iteration required is small . Here we have proposed novel approach to arrive at initial partitioning by using spectralfactorization method the results was verified using several circuits.

  20. Meridional Considerations of the Centrifugal Compressor Development

    Directory of Open Access Journals (Sweden)

    C. Xu

    2012-01-01

    Full Text Available Centrifugal compressor developments are interested in using optimization procedures that enable compressor high efficiency and wide operating ranges. Recently, high pressure ratio and efficiency of the centrifugal compressors require impeller design to pay attention to both the blade angle distribution and the meridional profile. The geometry of the blades and the meridional profile are very important contributions of compressor performance and structure reliability. This paper presents some recent studies of meridional impacts of the compressor. Studies indicated that the meridional profiles of the impeller impact the overall compressor efficiency and pressure ratio at the same rotational speed. Proper meridional profiles can improve the compressor efficiency and increase the overall pressure ratio at the same blade back curvature.

  1. Fault Detection and Isolation in Centrifugal Pumps

    DEFF Research Database (Denmark)

    Kallesøe, Carsten

    Centrifugal pumps are used in a variety of different applications, such as water supply, wastewater, and different industrial applications. Some pump installations are crucial for the applications to work. Failures can lead to substantial economic losses and can influence the life of many people...... when they occur. Therefore, detection of faults, if possible in an early stage, and isolation of their causes are of great interest. Especially fault detection, which can be used for predictive maintenance, can decrease working expenses and increase the reliability of the application in which the pump...... is placed. The topic of this work is Fault Detection and Identification in centrifugal pumps. Different approaches are developed with special focus on robustness. Robustness with respect to disturbances, unknown parts of the system, and parameter variations are considered. All developed algorithms...

  2. Mathematical model of the dynamics of countercurrent chromatography

    Institute of Scientific and Technical Information of China (English)

    陆向红; 任其龙; 吴平东

    2002-01-01

    A mathematical model of the dynamic behavior of countercurrent chromatography was proposed, and the model parameters, including the partition coefficient, the axial dispersion coefficient, the intraparticle diffusion coefficient and the external mass ransfer coefficient were calculated by the method of chromatogram moment analysis. Comparison of the experimental chromatograms of caffeine and theophylline determined in this work with the simulated curves computed by the proposed model showed fairly good agreement. Further, the difference between the average identified the partition coefficients by chromatogram moment analysis and the experimental values was small also, and the relationship between the external mass transfer rate and the linear velocity was similar to that obtained with solid-liquid chromatography.

  3. Analysis of Secondary Flows in Centrifugal Impellers

    OpenAIRE

    2005-01-01

    Secondary flows are undesirable in centrifugal compressors as they are a direct cause for flow (head) losses, create nonuniform meridional flow profiles, potentially induce flow separation/stall, and contribute to impeller flow slip; that is, secondary flows negatively affect the compressor performance. A model based on the vorticity equation for a rotating system was developed to determine the streamwise vorticity from the normal and binormal vorticity components (which are known from the me...

  4. Centrifugal shot blasting. Innovative technology summary report

    Energy Technology Data Exchange (ETDEWEB)

    1999-07-01

    At the US Department of Energy (DOE) Fernald Environmental Management Project (FEMP), the Facilities Closure and Demolition Projects Integrated Remedial Design/Remedial Action (RD/RA) work plan calls for the removal of one inch (1 in) depth of concrete surface in areas where contamination with technetium-99 has been identified. This report describes a comparative demonstration between two concrete removal technologies: an innovative system using Centrifugal Shot Blasting (CSB) and a modified baseline technology called a rotary drum planer.

  5. Predicting Droplet Formation on Centrifugal Microfluidic Platforms

    OpenAIRE

    Moebius, Jacob Alfred

    2015-01-01

    Centrifugal microfluidics is a widely known research tool for biological sample and water quality analysis. Currently, the standard equipment used for such diagnostic applications include slow, bulky machines controlled by multiple operators. These machines can be condensed into a smaller, faster benchtop sample-to-answer system.Sample processing is an important step taken to extract, isolate, and convert biological factors, such as nucleic acids or proteins, from a raw sample to an analyzabl...

  6. Centrifugal compressor design choices for chillers

    Energy Technology Data Exchange (ETDEWEB)

    Brasz, J.J. [United Technologies Carrier, New York, NY (United States)

    1999-07-01

    The use of centrifugal compressors in the air conditioning and refrigeration industry is currently limited to large water cooled chillers varying in size from about 0.5 to 6 MW cooling capacity. These systems are primarily used for comfort or process cooling applications. All systems try to chill relatively large amounts of indoor or process water by a few degrees Celsius in a refrigerant evaporator. The heat removed from the chilled water is released together with the heat of compression in a refrigerant condenser to cooling tower water, from where it is discharged to the atmosphere. Different centrifugal compressor design concepts are used by the various chiller manufacturers: single-stage versus multi-stage, vaneless versus vaned diffuser, hermetic versus open-drive motors, shrouded versus open impellers, fixed versus variable diffuser geometry, low- versus high-pressure refrigerant. This variability seems strange for a mature industry like the air conditioning and refrigeration industry. This paper will show that the reason for this variability is the product compromise between the various conflicting system requirements with respect to size, cost, efficiency and refrigerant choice. The different system applications of the chillers (e.g. comfort cooling in a equatorial region versus process cooling in a moderate climate zone) play another major role in selecting an optimal centrifugal compression concept. Some general recommendations will be given for applications where a clear choice can be made. (Author)

  7. CFD Simulation of Annular Centrifugal Extractors

    Directory of Open Access Journals (Sweden)

    S. Vedantam

    2012-01-01

    Full Text Available Annular centrifugal extractors (ACE, also called annular centrifugal contactors offer several advantages over the other conventional process equipment such as low hold-up, high process throughput, low residence time, low solvent inventory and high turn down ratio. The equipment provides a very high value of mass transfer coefficient and interfacial area in the annular zone because of the high level of power consumption per unit volume and separation inside the rotor due to the high g of centrifugal field. For the development of rational and reliable design procedures, it is important to understand the flow patterns in the mixer and settler zones. Computational Fluid Dynamics (CFD has played a major role in the constant evolution and improvements of this device. During the past thirty years, a large number of investigators have undertaken CFD simulations. All these publications have been carefully and critically analyzed and a coherent picture of the present status has been presented in this review paper. Initially, review of the single phase studies in the annular region has been presented, followed by the separator region. In continuation, the two-phase CFD simulations involving liquid-liquid and gas-liquid flow in the annular as well as separator regions have been reviewed. Suggestions have been made for the future work for bridging the existing knowledge gaps. In particular, emphasis has been given to the application of CFD simulations for the design of this equipment.

  8. Stable isotope enrichment using a plasma centrifuge

    Science.gov (United States)

    Krishnan, Mahadevan; Bures, Brian; Madden, Robert

    2012-10-01

    A primary goal of the Department of Energy's Isotope Development and Production for Research and Applications Program (Isotope Program) within the Office of Nuclear Physics (NP) is to produce isotopes that are in short supply in the U.S. and of which there exists no or insufficient domestic commercial production capability. A vacuum arc plasma centrifuge is a rigid rotor column of metal plasma in which centrifugal forces re-distribute ions radially according to their mass/charge ratio. Early work demonstrated rotation at 2 million rpm and separation of various stable isotopes. The spinning plasma column had a Gaussian flux profile, peaked on the rigid rotor axis. This work adopts a more efficient approach, with the plasma created as a hollow column, wherein the flux is concentrated at larger radii where the centrifugal action is highest. By tailoring the vacuum arc discharge geometry, the rotation rate can also be increased to ˜10 million rpm. Data from Cu, Al and other metal plasmas will be presented and discussed in light of enriched stable isotopes needed for research and medicine.

  9. Shallow water model for horizontal centrifugal casting

    Science.gov (United States)

    Boháček, J.; Kharicha, A.; Ludwig, A.; Wu, M.

    2012-07-01

    A numerical model was proposed to simulate the solidification process of an outer shell of work roll made by the horizontal centrifugal casting technique. Shallow water model was adopted to solve the 2D average flow dynamics of melt spreading and the average temperature distribution inside the centrifugal casting mould by considering the centrifugal force, Coriolis force, viscous force due to zero velocity on the mould wall, gravity, and energy transport by the flow. Additionally, a 1D sub-model was implemented to consider the heat transfer in the radial direction from the solidifying shell to the mould. The solidification front was tracked by fulfilling the Stefan condition. Radiative and convective heat losses were included from both, the free liquid surface and the outer wall of the mould. Several cases were simulated with the following assumed initial conditions: constant height of the liquid metal (10, 20, and 30 mm), uniform temperature of the free liquid surface (1755 K). The simulation results have shown that while the solidification front remained rather flat, the free surface was disturbed by waves. The amplitude of waves increased with the liquid height. Free surface waves diminished as the solidification proceeded.

  10. Classification algorithms using adaptive partitioning

    KAUST Repository

    Binev, Peter

    2014-12-01

    © 2014 Institute of Mathematical Statistics. Algorithms for binary classification based on adaptive tree partitioning are formulated and analyzed for both their risk performance and their friendliness to numerical implementation. The algorithms can be viewed as generating a set approximation to the Bayes set and thus fall into the general category of set estimators. In contrast with the most studied tree-based algorithms, which utilize piecewise constant approximation on the generated partition [IEEE Trans. Inform. Theory 52 (2006) 1335.1353; Mach. Learn. 66 (2007) 209.242], we consider decorated trees, which allow us to derive higher order methods. Convergence rates for these methods are derived in terms the parameter - of margin conditions and a rate s of best approximation of the Bayes set by decorated adaptive partitions. They can also be expressed in terms of the Besov smoothness β of the regression function that governs its approximability by piecewise polynomials on adaptive partition. The execution of the algorithms does not require knowledge of the smoothness or margin conditions. Besov smoothness conditions are weaker than the commonly used Holder conditions, which govern approximation by nonadaptive partitions, and therefore for a given regression function can result in a higher rate of convergence. This in turn mitigates the compatibility conflict between smoothness and margin parameters.

  11. Green chromatography.

    Science.gov (United States)

    Płotka, Justyna; Tobiszewski, Marek; Sulej, Anna Maria; Kupska, Magdalena; Górecki, Tadeusz; Namieśnik, Jacek

    2013-09-13

    Analysis of organic compounds in samples characterized by different composition of the matrix is very important in many areas. A vast majority of organic compound determinations are performed using gas or liquid chromatographic methods. It is thus very important that these methods have negligible environmental impact. Chromatographic techniques have the potential to be greener at all steps of the analysis, from sample collection and preparation to separation and final determination. The paper summarizes the approaches used to accomplish the goals of green chromatography. While complete elimination of sample preparation would be an ideal approach, it is not always practical. Solventless extraction techniques offer a very good alternative. Where solvents must be used, the focus should be on the minimization of their consumption. The approaches used to make chromatographic separations greener differ depending on the type of chromatography. In gas chromatography it is advisable to move away from using helium as the carrier gas because it is a non-renewable resource. GC separations using low thermal mass technology can be greener because of energy savings offered by this technology. In liquid chromatography the focus should be on the reduction of solvent consumption and replacement of toxic and environmentally hazardous solvents with more benign alternatives. Multidimensional separation techniques have the potential to make the analysis greener in both GC and LC. The environmental impact of the method is often determined by the location of the instrument with respect to the sample collection point.

  12. Ion Chromatography.

    Science.gov (United States)

    Mulik, James D.; Sawicki, Eugene

    1979-01-01

    Accurate for the analysis of ions in solution, this form of analysis enables the analyst to directly assay many compounds that previously were difficult or impossible to analyze. The method is a combination of the methodologies of ion exchange, liquid chromatography, and conductimetric determination with eluant suppression. (Author/RE)

  13. A critical evaluation of Amicon Ultra centrifugal filters for separating proteins, drugs and nanoparticles in biosamples.

    Science.gov (United States)

    Johnsen, Elin; Brandtzaeg, Ole Kristian; Vehus, Tore; Roberg-Larsen, Hanne; Bogoeva, Vanya; Ademi, Ornela; Hildahl, Jon; Lundanes, Elsa; Wilson, Steven Ray

    2016-02-20

    Amicon(®) Ultra centrifugal filters were critically evaluated for various sample preparations, namely (a) proteome fractionation, (b) sample cleanup prior to liquid chromatography mass spectrometry (LC-MS) measurement of small molecules in cell lysate, and (c) separating drug-loaded nanoparticles and released drugs for accurate release profiling in biological samples. (a) Filters of supposedly differing molar mass (MM) selectivity (10, 30, 50 and 100K) were combined to attempt fractionation of samples of various complexity and concentration. However, the products had surprisingly similar MM retentate/filtrate profiles, and the filters were unsuited for proteome fractionation. (b) Centrifugal filtration was the only clean-up procedure in a FDA-guideline validated LC-MS method for determining anti-tuberculosis agents rifampicin and thioridazine in macrophage cell lysate. An additional organic solvent washing step (drug/protein-binding disruption) was required for satisfactory recovery. (c) The centrifugation filters are well suited for separating drugs and nanoparticles in simple aqueous solutions, but significantly less so for biological samples, as common drug-protein binding disruptors can dissolve NPs or be incompatible with LC-MS instrumentation.

  14. A simple sample preparation method for measuring amoxicillin in human plasma by hollow fiber centrifugal ultrafiltration.

    Science.gov (United States)

    Dong, Wei-Chong; Hou, Zi-Li; Jiang, Xin-Hui; Jiang, Ye

    2013-02-01

    A simple sample preparation method has been developed for the determination of amoxicillin in human plasma by hollow fiber centrifugal ultrafiltration (HF-CF-UF). A 400-μL plasma sample was placed directly into the HF-CF-UF device, which consisited of a slim glass tube and a U-shaped hollow fiber. After centrifugation at 1.25 × 10(3) g for 10 min, the filtrate was withdrawn from the hollow fiber and 20 µL was directly injected into the high-performance liquid chromatography (HPLC) for analysis. The calibration curve was linear over the range of 0.1-20 µg/mL (r = 0.9996) and the limit of detection was as low as 0.025 µg/mL. The average recovery and absolute recovery were 99.9% and 84.5%, respectively. Both the intra-day and inter-day precisions (relative standard deviation) were less than 3.1% for three concentrations (0.25, 2.5 and 10 µg/mL). The sample preparation process was simplified. Only after a single centrifugal ultrafiltration can the filtrate be injected directly into HPLC. The present method is simple, sensitive and accurate. It could be effective for the analysis of biological samples with high protein contents, especially for the biopharmaceutical analysis of drugs that use traditional isolation techniques for sample preparation such as the protein precipitation method.

  15. Extremal sizes of subspace partitions

    CERN Document Server

    Heden, Olof; Nastase, Esmeralda; Sissokho, Papa

    2011-01-01

    A subspace partition $\\Pi$ of $V=V(n,q)$ is a collection of subspaces of $V$ such that each 1-dimensional subspace of $V$ is in exactly one subspace of $\\Pi$. The size of $\\Pi$ is the number of its subspaces. Let $\\sigma_q(n,t)$ denote the minimum size of a subspace partition of $V$ in which the largest subspace has dimension $t$, and let $\\rho_q(n,t)$ denote the maximum size of a subspace partition of $V$ in which the smallest subspace has dimension $t$. In this paper, we determine the values of $\\sigma_q(n,t)$ and $\\rho_q(n,t)$ for all positive integers $n$ and $t$. Furthermore, we prove that if $n\\geq 2t$, then the minimum size of a maximal partial $t$-spread in $V(n+t-1,q)$ is $\\sigma_q(n,t)$.

  16. Gentile statistics and restricted partitions

    Indian Academy of Sciences (India)

    C S Srivatsan; M V N Murthy; R K Bhaduri

    2006-03-01

    In a recent paper (Tran et al, Ann. Phys. 311, 204 (2004)), some asymptotic number theoretical results on the partitioning of an integer were derived exploiting its connection to the quantum density of states of a many-particle system. We generalise these results to obtain an asymptotic formula for the restricted or coloured partitions $p_{k}^{s} (n)$, which is the number of partitions of an integer into the summand of th powers of integers such that each power of a given integer may occur utmost times. While the method is not rigorous, it reproduces the well-known asymptotic results for = 1 apart from yielding more general results for arbitrary values of .

  17. Development of a test system for high level liquid waste partitioning

    Directory of Open Access Journals (Sweden)

    Duan Wu H.

    2015-01-01

    Full Text Available The partitioning and transmutation strategy has increasingly attracted interest for the safe treatment and disposal of high level liquid waste, in which the partitioning of high level liquid waste is one of the critical technical issues. An improved total partitioning process, including a tri-alkylphosphine oxide process for the removal of actinides, a crown ether strontium extraction process for the removal of strontium, and a calixcrown ether cesium extraction process for the removal of cesium, has been developed to treat Chinese high level liquid waste. A test system containing 72-stage 10-mm-diam annular centrifugal contactors, a remote sampling system, a rotor speed acquisition-monitoring system, a feeding system, and a video camera-surveillance system was successfully developed to carry out the hot test for verifying the improved total partitioning process. The test system has been successfully used in a 160 hour hot test using genuine high level liquid waste. During the hot test, the test system was stable, which demonstrated it was reliable for the hot test of the high level liquid waste partitioning.

  18. The complexity of string partitioning

    CERN Document Server

    Condon, Anne; Thachuk, Chris

    2012-01-01

    Given a string $w$ over a finite alphabet $\\Sigma$ and an integer $K$, can $w$ be partitioned into strings of length at most $K$, such that there are no \\emph{collisions}? We refer to this question as the \\emph{string partition} problem and show it is \\NP-complete for various definitions of collision and for a number of interesting restrictions including $|\\Sigma|=2$. This establishes the hardness of an important problem in contemporary synthetic biology, namely, oligo design for gene synthesis.

  19. The Partition Ensemble Fallacy Fallacy

    CERN Document Server

    Nemoto, K; Nemoto, Kae; Braunstein, Samuel L.

    2002-01-01

    The Partition Ensemble Fallacy was recently applied to claim no quantum coherence exists in coherent states produced by lasers. We show that this claim relies on an untestable belief of a particular prior distribution of absolute phase. One's choice for the prior distribution for an unobservable quantity is a matter of `religion'. We call this principle the Partition Ensemble Fallacy Fallacy. Further, we show an alternative approach to construct a relative-quantity Hilbert subspace where unobservability of certain quantities is guaranteed by global conservation laws. This approach is applied to coherent states and constructs an approximate relative-phase Hilbert subspace.

  20. Partitions of generalized split graphs

    OpenAIRE

    Shklarsky, Oren

    2012-01-01

    We discuss matrix partition problems for graphs that admit a partition into k independent sets and ` cliques. We show that when k + ` 6 2, any matrix M has finitely many (k; `) minimal obstructions and hence all of these problems are polynomial time solvable. We provide upper bounds for the size of any (k; `) minimal obstruction when k = ` = 1 (split graphs), when k = 2; ` = 0 (bipartite graphs), and when k = 0; ` = 2 (co-bipartite graphs). When k = ` = 1, we construct an exponential size spl...

  1. Measurements of Protein-Protein Interactions by Size Exclusion Chromatography

    OpenAIRE

    Bloustine, J.; Berejnov, V.; Fraden, S

    2003-01-01

    A method is presented for determining second virial coefficients (B2) of protein solutions from retention time measurements in size exclusion chromatography. We determine B2 by analyzing the concentration dependence of the chromatographic partition coefficient. We show the ability of this method to track the evolution of B2 from positive to negative values in lysozyme and bovine serum albumin solutions. Our size exclusion chromatography results agree quantitatively with data obtained by light...

  2. Freeze-out extraction of monocarboxylic acids from water into acetonitrile under the action of centrifugal forces

    Science.gov (United States)

    Bekhterev, V. N.

    2016-10-01

    It is established that the efficiency of the freezing-out extraction of monocarboxylic acids C3-C;8 and sorbic acid from water into acetonitrile increases under the action of centrifugal forces. The linear growth of the partition coefficient in the homologous series of C2-C8 acids with an increase in molecule length, and the difference between the efficiency of extracting sorbic and hexanoic acid, are discussed using a theoretical model proposed earlier and based on the adsorption-desorption equilibrium of the partition of dissolved organic compounds between the resulting surface of ice and the liquid phase of the extract. The advantages of the proposed technique with respect to the degree of concentration over the method of low-temperature liquid-liquid extraction are explained in light of the phase diagram for the water-acetonitrile mixture.

  3. ELECTRO-HYDRAULIC SERVO SYSTEM IN THE CENTRIFUGE FIELD

    Institute of Scientific and Technical Information of China (English)

    Dong Longlei; Yan Guirong; Li Ronglin

    2004-01-01

    The mechanical characteristics of the electro-hydraulic servo system in the centrifuge field are analyzed.The hydraulic pressure law in the centrifuge field indicates the existence of the centrifuge hydraulic pressure.The mechanical characteristics of the slide-valve and the dual nozzle flapper valve are studied,and it is found that the centrifuge field can not only increase the driving force or moment of the function units,but also decrease the stability of the components.Finally by applying Gauss minimum constraint principle,the dynamic model of the electro-hydraulic vibrator in the centrifuge field is established,and the mechanical restriction of the system is also presented.The study will be helpful for the realization of the combined vibration and centrifuge test system.

  4. Gershgorin domains for partitioned matrices

    NARCIS (Netherlands)

    Sluis, A. van der

    1979-01-01

    Inclusion domains for the eigenvalues of a partitioned matrix are specified in terms of perturbations of its diagonal blocks. The size of such perturbations is measured using the Kantorovitch-Robert-Deutsch vectorial norms. The inclusion domains obtained thereby are compared with inclusion domains o

  5. Assimilate Partitioning and Plant Development

    Institute of Scientific and Technical Information of China (English)

    Yong-Ling Ruan; John W.Patrick; Hans Weber

    2010-01-01

    @@ It has been a pleasure to organize this special issue of Molecular Plant on 'Assimilate Partitioning and Plant Development'. Assimilate, a collective term describing organic carbon (C) and nitrogen (N), is of paramount importance for plant development and realization of crop productivity.

  6. Fabrication of bulk metallic glasses by centrifugal casting method

    OpenAIRE

    R. Nowosielski; R. Babilas

    2007-01-01

    Purpose: The aim of the present work is characterization of the centrifugal casting method, apparatus andproduced amorphous materials, which are also known as bulk metallic glassesDesign/methodology/approach: The studied centrifugal casting system consists of two main parts: castingapparatus and injection system of molten alloy. The described centrifugal casting method was presented bypreparing a casting apparatus “CentriCast – 5”. The apparatus includes a cylindrical copper mold, which isrot...

  7. A curious spacetime entirely free of centrifugal acceleration

    CERN Document Server

    Dadhich, Naresh

    2012-01-01

    In the Einstein gravity, besides the usual gravitational and centrifugal potential there is an additional attractive term that couples these two together. It is fun to enquire whether the latter could fully counteract the centrifugal repulsion everywhere making the spacetime completely free of the centrifugal acceleration. We present here such a curious spacetime metric and it produces a global monopole like stresses going as $~1/r^2$ in an AdS spacetime.

  8. Design and Prototyping of Micro Centrifugal Compressor

    Institute of Scientific and Technical Information of China (English)

    Shimpei Mizuki; Gaku Minorikawa; Toshiyuki Hirano; Yuichiro Asaga; Naoki Yamaguchi; Yutaka Ohta; Eisuke Outa

    2003-01-01

    In order to establish the design methodology of ultra micro centrifugal compressor, which is the most important component of ultra micro gas turbine unit, a 10 times of the final target size model was designed, prototyped and tested. The problems to be solved for downsizing were examined and 2-dimensional impeller was chosen as the first model due to its productivity. The conventional 1D prediction method, CFD and the inverse design were attempted. The prototyped compressor was driven by using a turbocharger and the performance characteristics were measured.

  9. Rotational spectroscopy with an optical centrifuge

    CERN Document Server

    Korobenko, Aleksey; Hepburn, John W; Milner, Valery

    2013-01-01

    We demonstrate a new spectroscopic method for studying electronic transitions in molecules with extremely broad range of angular momentum. We employ an optical centrifuge to create narrow rotational wave packets in the ground electronic state of $^{16}$O$_2$. Using the technique of resonance-enhanced multi-photon ionization, we record the spectrum of multiple ro-vibrational transitions between $X^3\\Sigma_{g}^{-}$ and $C^3\\Pi_{g}$ electronic manifolds of oxygen. Direct control of rotational excitation, extending to rotational quantum numbers as high as $N\\gtrsim 120$, enables us to interpret the complex structure of rotational spectra of $C^3\\Pi_{g}$ beyond thermally accessible levels.

  10. Theory and experiments on centrifuge cratering

    Science.gov (United States)

    Schmidt, R. M.; Holsapple, K. A.

    1980-01-01

    Centrifuge experimental techniques provide possibilities for laboratory simulation of ground motion and cratering effects due to explosive loadings. The results of a similarity analysis for the thermomechanical response of a continuum show that increased gravity is a necessary condition for subscale testing when identical materials for both model and prototype are being used. The general similarity requirements for this type of subscale testing are examined both theoretically and experimentally. The similarity analysis is used to derive the necessary and sufficient requirements due to the general balance and jump equations and gives relations among all the scale factors for size, density, stress, body forces, internal energy, heat supply, heat conduction, heat of detonation, and time. Additional constraints due to specific choices of material constitutive equations are evaluated separately. The class of constitutive equations that add no further requirements is identified. For this class of materials, direct simulation of large-scale cratering events at small scale on the centrifuge is possible and independent of the actual constitutive equations. For a rate-independent soil it is shown that a small experiment at gravity g and energy E is similar to a large event at 1 G but with energy equal to g3E. Consequently, experiments at 500 G with 8 grams of explosives can be used to simulate a kiloton in the field. A series of centrifuge experiments was performed to validate the derived similarity requirements and to determine the practicality of applying the technique to dry granular soils having little or no cohesion. Ten shots using Ottawa sand at various gravities confirmed reproducibility of results in the centrifuge environment, provided information on particle size effects, and demonstrated the applicability of the derived similitude requirements. These experiments used 0.5-4 grams of pentaerythritol-tetranitrate (PETN) and 1.7 grams of lead-azide explosives. They

  11. Development of liquid nitrogen Centrifugal Pump

    Energy Technology Data Exchange (ETDEWEB)

    Abe, M; Sagiyama, R; Tsuchiya, H [Institute for Solid State Physics, University of Tokyo, 5-1-5 Kashiwanoha, Kashiwa, Chiba 277-8581 (Japan); Takayama, T [Institute for Molecular Science, National Institutes of Natural Sciences, 38 Nishigo-Naka, Myodaiji, Okazaki, Aichi 444-8585 (Japan); Torii, Y [OMNIX, 1-15-3 Nishishinjuku, Shinjuku, Tokyo, 160-0023 (Japan); Nakamura, M [YN Nakamura Ltd, 3-9-25 Ohjima, Koto, Tokyo, 136-0072 (Japan); Hoshino, Y [JECC TORISHA Co. Ltd, 2-8-52 Yoshinodai, Kawagoe-shi, Saitama, 350-0833 (Japan); Odashima, Y [Department of Basic Sciences, University of Tokyo, 3-8-1 Komaba, Meguro, Tokyo 153-8902 (Japan)], E-mail: mirei@issp.u-tokyo.ac.jp

    2009-02-01

    Usually liquid nitrogen (LN{sub 2}) transfer from a container to a laboratory equipment takes place by applying pressure to the container to push out liquid or pouring liquid into the cryostat directly by lifting the container. In order to overcome inconvenience of pressuring or lifting containers, we have been developing the Liquid Nitrogen Centrifugal Pump of a small electric turbine pump. Significant advantages that both reducing time to fill LN{sub 2}and controlling the flow rate of liquid into the cryostat are obtained by introducing this pump. We have achieved the lift of about 800mm with the vessel's opening diameter of 28mm.

  12. Separative power of an optimised concurrent gas centrifuge

    Energy Technology Data Exchange (ETDEWEB)

    Bogovalov, Sergey; Boman, Vladimir [National Research Nuclear University (MEPHI), Moscow (Russian Federation)

    2016-06-15

    The problem of separation of isotopes in a concurrent gas centrifuge is solved analytically for an arbitrary binary mixture of isotopes. The separative power of the optimised concurrent gas centrifuges for the uranium isotopes equals to δU = 12.7 (V/700 m/s)2(300 K/T)(L/1 m) kg·SWU/yr, where L and V are the length and linear velocity of the rotor of the gas centrifuge and T is the temperature. This equation agrees well with the empirically determined separative power of optimised counter-current gas centrifuges.

  13. [Design and optimization of a centrifugal pump for CPCR].

    Science.gov (United States)

    Pei, J; Tan, X; Chen, K; Li, X

    2000-06-01

    Requirements for an optimal centrifugal pump, the vital component in the equipment for cardiopulmonary cerebral resuscitation(CPCR), have been presented. The performance of the Sarns centrifugal pump (Sarns, Inc./3M, Ann arbor, MI, U.S.A) was tested. The preliminarily optimized model for CPCR was designed according to the requirements of CPCR and to the comparison and analysis of several clinically available centrifugal pumps. The preliminary tests using the centrifugal pump made in our laboratory(Type CPCR-I) have confirmed the design and the optimization.

  14. Computer simulation for centrifugal mold filling of precision titanium castings

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    Computer simulation codes were developed based on a proposed mathematical model for centrifugal mold filling processes and previous computer software for 3D mold filling and solidification of castings (CASM-3D for Windows). Sample simulations were implemented for mold filling processes of precision titanium castings under gravity and different centrifugal casting techniques. The computation results show that the alloy melt has a much stronger mold filling ability for thin section castings under a centrifugal force field than that only under the gravity. A "return back" mold filling manner is showed to be a reasonable technique for centrifugal casting processes, especially for thin section precision castings.

  15. Separative Power of an Optimised Concurrent Gas Centrifuge

    Directory of Open Access Journals (Sweden)

    Sergey Bogovalov

    2016-06-01

    Full Text Available The problem of separation of isotopes in a concurrent gas centrifuge is solved analytically for an arbitrary binary mixture of isotopes. The separative power of the optimised concurrent gas centrifuges for the uranium isotopes equals to δU = 12.7 (V/700 m/s2(300 K/T(L/1 m kg·SWU/yr, where L and V are the length and linear velocity of the rotor of the gas centrifuge and T is the temperature. This equation agrees well with the empirically determined separative power of optimised counter-current gas centrifuges.

  16. Research on the development of the centrifugal spinning

    Directory of Open Access Journals (Sweden)

    Zhang Zhiming

    2017-01-01

    Full Text Available Centrifugal spinning is a new and efficient method to produce nanofibers quickly. It makes use of the centrifugal force instead of high voltage to produce the nanofibers. The centrifugal spinning has many advantages such as no high voltage, high yield, simple structure, no pollution and can be applied to high polymer material, ceramic and metal material. In order to have more understand about this novel nanofibers formation method, this paper introduces the method of centrifugal spinning and the effect of rotation speed, the properties of material such as viscosity and solvent evaporation, collector distance which have an impact on nanofibers morphology and diameter were also analyzed.

  17. On free fermions and plane partitions

    CERN Document Server

    Foda, O; Zuparic, M

    2008-01-01

    We use free fermion methods to re-derive a result of Okounkov and Reshetikhin relating charged fermions to random plane partitions, and to extend it to relate neutral fermions to strict plane partitions.

  18. Optimized Local Trigonometric Bases with Nonuniform Partitions

    Institute of Scientific and Technical Information of China (English)

    Qiao Fang LIAN; Yong Ge WANG; Dun Yan YAN

    2006-01-01

    The authors provide optimized local trigonometric bases with nonuniform partitions which efficiently compress trigonometric functions. Numerical examples demonstrate that in many cases the proposed bases provide better compression than the optimized bases with uniform partitions obtained by Matviyenko.

  19. Solving set partitioning problems using lagrangian relaxation

    NARCIS (Netherlands)

    van Krieken, M.G.C.

    2006-01-01

    This thesis focuses on the set partitioning problem. Given a collection of subsets of a certain root set and costs associated to these subsets, the set partitioning problem is the problem of finding a minimum cost partition of the root set. Many real-life problems, such as vehicle routing and crew s

  20. Postcardiotomy centrifugal assist: a single surgeon's experience.

    Science.gov (United States)

    Curtis, Jack J; McKenney-Knox, Charlotte A; Wagner-Mann, Colette C

    2002-11-01

    Because of the infrequent application of cardiac assist devices for postcardiotomy heart failure, most published reports include the results of learning curves from multiple surgeons. Between October 1986 and June 2001, a single surgeon used 35 Sarns Centrifugal Pumps as ventricular assist devices in 21 patients with severe hemodynamic compromise after open heart surgery (0.88% incidence). Patients' ages ranged from 39 to 77 (mean, 59.6 years). Three patients required right ventricular assist devices, 4 left ventricular assist devices, and 14 had biventricular assist devices. For all, the indication for application was inability to wean from cardiopulmonary bypass despite multiple inotropes and intraaortic balloon pumping. All were expected to be intraoperative deaths without further mechanical assistance. Patients were assisted from 2 to 434 h (median, 48 h). Fifteen patients (71.4%) were weaned from device(s), and 11 patients (52.4%) were hospital survivors. Actuarial survival in those dismissed from the hospital was 78% at 5 years and 39% at 10 years. Patients facing certain demise after cardiac surgery can be salvaged with temporary centrifugal mechanical assist. Results are competitive with that achieved with more sophisticated devices. Hospital survivors enjoy reasonable longevity.

  1. Some aversive characteristics of centrifugally generated gravity.

    Science.gov (United States)

    Altman, F.

    1973-01-01

    The effective weight of rats was manipulated by centrifugation. Two effective weight levels were obtained. In three escape avoidance conditions a lever press produced a change from a base level of 2.1 g to a response level of 1.1 g. In a punishment condition a response produced a change from a 1.1 g level to a 2.1 g level and in an extinction condition responses had no effect on the 2.1 g effective weight level present. All changes took 30 sec and were maintained for an additional 10 sec before a return to base level was initiated. When responses occurred closer together than the 40 sec, they delayed the return to base level by 40 sec. This 40 sec interval is referred to as response-contingent-time. The response rate and amount of response-contingent-time served as the data. The results confirmed previous data that centrifugation is aversive. The results are interpreted as indicating that the aversiveness is attributable to the increase in effective weight, and that rats can discriminate the different angular velocity-radius of rotation combinations used.

  2. Centrifugally Stimulated Exospheric Ion Escape at Mercury

    Science.gov (United States)

    Delcourt, Dominique; Seki, K.; Terada, N.; Moore, Thomas E.

    2012-01-01

    We investigate the transport of ions in the low-altitude magnetosphere magnetosphere of Mercury. We show that, because of small spatial scales, the centrifugal effect due to curvature of the E B drift paths can lead to significant particle energization in the parallel direction. We demonstrate that because of this effect, ions with initial speed smaller than the escape speed such as those produced via thermal desorption can overcome gravity and escape into the magnetosphere. The escape route of this low-energy exosphere originating material is largely controlled by the magnetospheric convection rate. This escape route spreads over a narrower range of altitudes when the convection rate increases. Bulk transport of low-energy planetary material thus occurs within a limited region of space once moderate magnetospheric convection is established. These results suggest that, via release of material otherwise gravitationally trapped, the E B related centrifugal acceleration is an important mechanism for the net supply of plasma to the magnetosphere of Mercury.

  3. PARTICLE DISTRIBUTION IN CENTRIFUGAL ACCELERATING FIELDS

    Institute of Scientific and Technical Information of China (English)

    Yu Sirong; Zhang Xinping; He Zhenming; Liu Yaohui

    2003-01-01

    Based on continuum theory and moving law of particles, a model is presented to obtain gradient distribution of particles in centrifugal accelerating field, by which the particle distribution in gradient composite material can be predicted. The simulation shows with increases in rotating time, four regions gradually appear from the internal periphery to the external one, they are free region, transition region, steady region and surface reinforced region,and the latest three regions are defined as a rich region. Finally, the steady region disappears, and the rich region only includes transition region and surface reinforced region. The influences of centrifugal acceleration coefficient G,primary volume fraction (0,pouring temperature (p and density difference between the particle and the metal matrix on particles gradient distribution are studied in detail. The results of the theoretical analysis agree with experiment ones. Both of analysis and experiment results indicate that with the increase in G and (p, the particle distribution becomes more centralized and the consistence of particle in the surface periphery becomes larger.

  4. How to Use Chromatography as a Science Teaching Aid.

    Science.gov (United States)

    Ganis, Frank M.

    Presented are five procedures which permit the effective teaching of chromatography with equipment which is readily available, economical, and simple in design. The first procedure involves a study of solute partition in two immiscible solvents and of countercurrent distribution. The second illustrates the use of unidimensional ascending paper…

  5. Gas Chromatography

    Science.gov (United States)

    Qian, Michael C.

    Gas chromatography (GC) has many applications in the analysis of food products. GC has been used for the determination of fatty acids, triglycerides, cholesterol, gases, water, alcohols, pesticides, flavor compounds, and many more. While GC has been used for other food components such as sugars, oligosaccharides, amino acids, peptides, and vitamins, these substances are more suited to analysis by high performance liquid chromatography. GC is ideally suited to the analysis of volatile substances that are thermally stable. Substances such as pesticides and flavor compounds that meet these criteria can be isolated from a food and directly injected into the GC. For compounds that are thermally unstable, too low in volatility, or yield poor chromatographic separation due to polarity, a derivatization step must be done before GC analysis. The two parts of the experiment described here include the analysis of alcohols that requires no derivatization step, and the analysis of fatty acids which requires derivatization. The experiments specify the use of capillary columns, but the first experiment includes conditions for a packed column.

  6. Ontology Partitioning: Clustering Based Approach

    Directory of Open Access Journals (Sweden)

    Soraya Setti Ahmed

    2015-05-01

    Full Text Available The semantic web goal is to share and integrate data across different domains and organizations. The knowledge representations of semantic data are made possible by ontology. As the usage of semantic web increases, construction of the semantic web ontologies is also increased. Moreover, due to the monolithic nature of the ontology various semantic web operations like query answering, data sharing, data matching, data reuse and data integration become more complicated as the size of ontology increases. Partitioning the ontology is the key solution to handle this scalability issue. In this work, we propose a revision and an enhancement of K-means clustering algorithm based on a new semantic similarity measure for partitioning given ontology into high quality modules. The results show that our approach produces meaningful clusters than the traditional algorithm of K-means.

  7. Discretized configurations and partial partitions

    CERN Document Server

    Abrams, Aaron; Hower, Valerie

    2010-01-01

    We show that the discretized configuration space of $k$ points in the $n$-simplex is homotopy equivalent to a wedge of spheres of dimension $n-k+1$. This space is homeomorphic to the order complex of the poset of ordered partial partitions of $\\{1,\\...,n+1\\}$ with exactly $k$ parts. We also compute the Euler characteristic in two different ways, thereby obtaining a topological proof of a combinatorial recurrence satisfied by the Stirling numbers of the second kind.

  8. High Efficiency Centrifugal Compressor for Rotorcraft Applications

    Science.gov (United States)

    Medic, Gorazd; Sharma, Om P.; Jongwook, Joo; Hardin, Larry W.; McCormick, Duane C.; Cousins, William T.; Lurie, Elizabeth A.; Shabbir, Aamir; Holley, Brian M.; Van Slooten, Paul R.

    2014-01-01

    The report "High Efficiency Centrifugal Compressor for Rotorcraft Applications" documents the work conducted at UTRC under the NRA Contract NNC08CB03C, with cost share 2/3 NASA, and 1/3 UTRC, that has been extended to 4.5 years. The purpose of this effort was to identify key technical barriers to advancing the state-of-the-art of small centrifugal compressor stages; to delineate the measurements required to provide insight into the flow physics of the technical barriers; to design, fabricate, install, and test a state-of-the-art research compressor that is representative of the rear stage of an axial-centrifugal aero-engine; and to acquire detailed aerodynamic performance and research quality data to clarify flow physics and to establish detailed data sets for future application. The design activity centered on meeting the goal set outlined in the NASA solicitation-the design target was to increase efficiency at higher work factor, while also reducing the maximum diameter of the stage. To fit within the existing Small Engine Components Test Facility at NASA Glenn Research Center (GRC) and to facilitate component re-use, certain key design parameters were fixed by UTRC, including impeller tip diameter, impeller rotational speed, and impeller inlet hub and shroud radii. This report describes the design effort of the High Efficiency Centrifugal Compressor stage (HECC) and delineation of measurements, fabrication of the compressor, and the initial tests that were performed. A new High-Efficiency Centrifugal Compressor stage with a very challenging reduction in radius ratio was successfully designed, fabricated and installed at GRC. The testing was successful, with no mechanical problems and the running clearances were achieved without impeller rubs. Overall, measured pressure ratio of 4.68, work factor of 0.81, and at design exit corrected flow rate of 3 lbm/s met the target requirements. Polytropic efficiency of 85.5 percent and stall margin of 7.5 percent were

  9. On higher spin partition functions

    CERN Document Server

    Beccaria, M

    2015-01-01

    We observe that the partition function of the set of all free massless higher spins s=0,1,2,3,... in flat space is equal to one: the ghost determinants cancel against the "physical" ones or, equivalently, the (regularized) total number of degrees of freedom vanishes. This reflects large underlying gauge symmetry and suggests analogy with supersymmetric or topological theory. The Z=1 property extends also to the AdS background, i.e. the 1-loop vacuum partition function of Vasiliev theory is equal to 1 (assuming a particular regularization of the sum over spins); this was noticed earlier as a consistency requirement for the vectorial AdS/CFT duality. We find that Z=1 is also true in the conformal higher spin theory (with higher-derivative d^{2s} kinetic terms) expanded near flat or conformally flat S^4 background. We also consider the partition function of free conformal theory of symmetric traceless rank s tensor field which has 2-derivative kinetic term but only scalar gauge invariance in flat space. This non...

  10. Use of centrifugal-gravity concentration for rejection of talc and recovery improvement in base-metal flotation

    Institute of Scientific and Technical Information of China (English)

    Bern Klein; Naci Emre Altun; Hassan Ghaffari

    2016-01-01

    The possibility of using a centrifugal-gravity concentrator to reject Mg-bearing minerals and minimize metal losses in the flotation of base metals was evaluated. Sample characterization, batch scoping tests, pilot-scale tests, and regrind-flotation tests were conducted on a Ni flotation tailings stream. Batch tests revealed that the Mg grade decreased dramatically in the concentrate products. Pilot-scale testing of a continuous centrifugal concentrator (Knelson CVD6) on the flotation tailings revealed that a concentrate with a low mass yield, low Mg con-tent, and high Ni upgrade ratio could be achieved. Under optimum conditions, a concentrate at 6.7%mass yield was obtained with 0.85%Ni grade at 12.9%Ni recovery and with a low Mg distribution (1.7%). Size partition curves demonstrated that the CVD also operated as a size classifier, enhancing the rejection of talc fines. Overall, the CVD was capable of rejecting Mg-bearing minerals. Moreover, an opportunity exists for the novel use of centrifugal-gravity concentration for scavenging flotation tailings and/or after comminution to minimize amount of Mg-bearing minerals reporting to flotation.

  11. Separative power of an optimised concurrent gas centrifuge

    CERN Document Server

    Bogovalov, S V

    2015-01-01

    The problem of separation of uranium isotopes in a concurrent gas centrifuge is solved analytically. Separative power of the optimized concurrent gas centrifuges equals to $\\delta U=12.7(V/700~{\\rm m/s})^2 (300 ~{\\rm K}/T)L, ~{\\rm kg ~SWU/yr}$, where $L$ and $V$ are the length and linear velocity of the rotor of the gas centrifuge, $T$ is the temperature. This formula well agrees with an empirical separative power of counter current gas centrifuges. The optimal value of the separative power is not unique on the plane $(p_w,v_z)$, where $p_w$ is pressure at the wall of the rotor and $v_z$ is axial velocity of the gas. This value is constant on a line defined by the equation $p_wv_z=constant$. Equations defining the mass flux and the electric power necessary to support the rotation of the gas centrifuge are obtained.

  12. Partitioning and transmutation (P and D) 1995. A review of the current state of the art

    Energy Technology Data Exchange (ETDEWEB)

    Skaalberg, M.; Landgren, A.; Spjuth, L.; Liljenzin, J.O. [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Nuclear Chemistry; Gudowski, W. [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Neutron and Reactor Physics

    1995-12-01

    The recent development in the field of partitioning and transmutation (P/T) is reviewed and evaluated. Current national and international R and D efforts are summarized. Nuclear transmutation with energy production is feasible in nuclear reactors where fast and thermal breeders are the most efficient for transmutation purposes. The operation of subcritical nuclear reactors by high current proton accelerators that generate neutrons in a spallation target is also an interesting option for transmutation and energy production, that has to be more carefully evaluated. These accelerator-driven systems are probably the only solution for the transmutation of long-lived fission products with small neutron capture cross sections and actinide isotopes with small fission cross sections. The requirements on the separation chemistry in the partitioning process depends on the transmutation strategy chosen. Recent developments in aqueous based separation chemistry opens some interesting possibilities to meet some of the requirements, such as separation of different actinides and some fission products and reduction of secondary waste streams. In the advanced accelerator-driven transmutation systems proposed, liquid fuels such as molten salts are considered. The partitioning processes that can be used for these types of fuel will, however, require a long term research program. The possibility to use centrifuge separation is an interesting partitioning option that recently has been proposed. 51 refs, 7 figs, 3 tabs.

  13. [Hemodynamic analysis of a centrifugal blood pump].

    Science.gov (United States)

    Wang, Yang; Yang, Ming; Xu, Zihao; Zhuang, Xiaoqi; Li, Qilei; Xu, Liang

    2015-01-01

    This paper built the mathematical model of a centrifugal blood pump, which was designed by ourselves, combined it with that of the human cardiovascular system and simulated the coupling system using Matlab. Then we set up the experiment platform, linked the blood pump to mock human cardiovascular system in case of three-stage heart failure, and measured aortic pressure and flow under different speed. The comparison between experiment results and simulation results not only indicates the coupling model is correct and the blood pump works well, but also shows that with the increase of blood pump speed, the pulsation of aortic pressure and flow will be reduced, this situation will affect the structure and function of blood vessels.

  14. Centrifugal acceleration of plasma in pulsar magnetosphere

    Indian Academy of Sciences (India)

    R T Gangadhara; V Krishna

    2003-12-01

    We present a relativistic model for the centrifugal acceleration of plasma bunches and the coherent radio emission in pulsar magnetosphere. We find that rotation broadens the width of leading component compared to the width of trailing component. We explain this difference in the component widths using the nested cone emission geometry. We estimate the effect of pulsar spin on the Stokes parameters, and find that the inclination between the rotation and magnetic axes can introduce an asymmetry in the circular polarization of the conal components. We analyse the single pulse polarization data of PSR B0329+54 at 606 MHz, and find that in its conal components, one sense of circular polarization dominates in the leading component while the other sense dominates in the trailing component. Our simulation shows that changing the sign of the impact parameter changes the sense of circular polarization as well as the swing of polarization angle.

  15. Numerical simulation of centrifugal casting of pipes

    Science.gov (United States)

    Kaschnitz, E.

    2012-07-01

    A numerical simulation model for the horizontal centrifugal pipe casting process was developed with the commercial simulation package Flow3D. It considers - additionally to mass, energy and momentum conservation equations and free surface tracking - the fast radial and slower horizontal movement of the mold. The iron inflow is not steady state but time dependent. Of special importance is the friction between the liquid and the mold in connection with the viscosity and turbulence of the iron. Experiments with the mold at controlled revolution speeds were carried out using a high-speed camera. From these experiments friction coefficients for the description of the interaction between mold and melt were obtained. With the simulation model, the influence of typical process parameters (e.g. melts inflow, mold movement, melt temperature, cooling media) on the wall thickness of the pipes can be studied. The comparison to results of pipes from production shows a good agreement between simulation and reality.

  16. A straight path centrifugal blood pump concept in the Capiox centrifugal pump.

    Science.gov (United States)

    Kijima, T; Oshiyama, H; Horiuchi, K; Nogawa, A; Hamasaki, H; Amano, N; Nojiri, C; Fukasawa, H; Akutsu, T

    1993-07-01

    This article describes comparative studies of a newly developed "straight path" centrifugal pump (Capiox centrifugal pump) targeted for open-heart surgery and circulatory support. A unique straight path design of the rotor was very effective in reducing the pump's rotational speed and prime volume. This pump was evaluated for hydraulics, hemolysis, depriming characteristics, cavitation, and heat generation. Two commercially available centrifugal pumps, the Biomedicus cone-type pump and the Sarns 3M impeller-type pump, were used as controls. The new pump required the lowest pump speed to produce the same flow rates under the same pressure loads and demonstrated the lowest hemolysis and the lowest temperature rise with the outlet clamped. The air volume required to deprime the new pump was one-third to one-half that for the other pumps, and no sign of cavitation was observed even if a small amount of air was introduced to the pump inlet under a negative pressure of 200 mm Hg.

  17. A Novel Fabrication Method for Functionally Graded Materials under Centrifugal Force: The Centrifugal Mixed-Powder Method

    Directory of Open Access Journals (Sweden)

    Eri Miura-Fujiwara

    2009-12-01

    Full Text Available One of the fabrication methods for functionally graded materials (FGMs is a centrifugal solid-particle method, which is an application of the centrifugal casting technique. However, it is the difficult to fabricate FGMs containing nano-particles by the centrifugal solid-particle method. Recently, we proposed a novel fabrication method, which we have named the centrifugal mixed-powder method, by which we can obtain FGMs containing nano-particles. Using this processing method, Cu-based FGMs containing SiC particles and Al-based FGMs containing TiO2 nano-particles on their surfaces have been fabricated. In this article, the microstructure and mechanical property of Cu/SiC and Al/TiO2 FGMs, fabricated by the centrifugal mixed-powder method are reviewed.

  18. Simulating retention in gas-liquid chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Martin, M.G.; Siepmann, J.I.; Schure, M.R.

    1999-12-16

    Accurate predictions of retention times, retention indices, and partition constants are a long sought-after goal for theoretical studies in chromatography. Configurational-bias Monte Carlo (CBMC) simulations in the Gibbs ensemble using the transferable potentials for phase equilibria-united atom (TraPPE-UA) force field have been carried out to obtain a microscopic picture of the partitioning of 10 alkane isomers between a helium vapor phase and a squalane liquid phase, a protypical gas-liquid chromatography system. The alkane solutes include some topological isomers that differ only in the arrangement of their building blocks (e.g., 2,5-dimethylhexane and 3,4-dimethylhexane), for which the prediction of the retention order is particularly difficult. The Kovats retention indices, a measure of the relative retention times, are calculated directly from the partition constants and are in good agreement with experimental values. The calculated Gibbs free energies of transfer for the normal alkanes conform to Martin's equation which is the basis of linear free energy relationships used in many process modeling packages. Analysis of radial distribution functions and the corresponding energy integrals does not yield evidence for specific retention structures and shows that the internal energy of solvation is not the main driving force for the separation of topological isomers in this system.

  19. Continuous-flow centrifugation to collect suspended sediment for chemical analysis

    Science.gov (United States)

    Conn, Kathleen E.; Dinicola, Richard S.; Black, Robert W.; Cox, Stephen E.; Sheibley, Richard W.; Foreman, James R.; Senter, Craig A.; Peterson, Norman T.

    2016-12-22

    Recent advances in suspended-sediment monitoring tools and surrogate technologies have greatly improved the ability to quantify suspended-sediment concentrations and to estimate daily, seasonal, and annual suspended-sediment fluxes from rivers to coastal waters. However, little is known about the chemical composition of suspended sediment, and how it may vary spatially between water bodies and temporally within a single system owing to climate, seasonality, land use, and other natural and anthropogenic drivers. Many water-quality contaminants, such as organic and inorganic chemicals, nutrients, and pathogens, preferentially partition in sediment rather than water. Suspended sediment-bound chemical concentrations may be undetected during analysis of unfiltered water samples, owing to small water sample volumes and analytical limitations. Quantification of suspended sediment‑bound chemical concentrations is needed to improve estimates of total chemical concentrations, chemical fluxes, and exposure levels of aquatic organisms and humans in receiving environments. Despite these needs, few studies or monitoring programs measure the chemical composition of suspended sediment, largely owing to the difficulty in consistently obtaining samples of sufficient quality and quantity for laboratory analysis.A field protocol is described here utilizing continuous‑flow centrifugation for the collection of suspended sediment for chemical analysis. The centrifuge used for development of this method is small, lightweight, and portable for the field applications described in this protocol. Project scoping considerations, deployment of equipment and system layout options, and results from various field and laboratory quality control experiments are described. The testing confirmed the applicability of the protocol for the determination of many inorganic and organic chemicals sorbed on suspended sediment, including metals, pesticides, polycyclic aromatic hydrocarbons, and

  20. Intrinsic energy partition in fission

    Directory of Open Access Journals (Sweden)

    Mirea M.

    2013-03-01

    Full Text Available The intrinsic energy partition between two complementary fission fragments is investigated microscopically. The intrinsic excitation energy of fission fragments is dynamically evaluated in terms of the time-dependent pairing equations. These equations are corroborated with two conditions. One of them fixes the number of particles and the other separates the pairing active spaces associated to the two fragments in the vicinity of the scission configuration. The excitation energy in a wide distribution of fission fragments is calculated for the 234U parent nucleus.

  1. Olive Fruit Phenols Transfer, Transformation, and Partition Trail during Laboratory-Scale Olive Oil Processing.

    Science.gov (United States)

    Jerman Klen, Tina; Golc Wondra, Alenka; Vrhovšek, Urška; Sivilotti, Paolo; Vodopivec, Branka Mozetič

    2015-05-13

    This work is the most comprehensive study on the quantitative behavior of olive fruit phenols during olive oil processing, providing insight into their transfer, transformation, and partition trail. In total, 69 phenols were quantified in 6 olive matrices from a three-phase extraction line employing ultra high pressure liquid chromatography-diode array detection analysis. Crushing had a larger effect than malaxation in terms of phenolic degradation and transformation, resulting in several new evolutions of respective derivatives. The peel and pulp together confined 95% of total fruit phenols, while stone only 5%. However, only 0.53% of all ended-up in olive oil, nearly 6% in wastewater, and 48% in pomace. Secoiridoids were the predominant class in all matrices, though represented by different individuals. Their partition behavior was rather similar to other phenolic classes, where with few minor exceptions only aglycones were partitioned to the oil, while other glycosides were lost with the wastes.

  2. The American Gas Centrifuge Past, Present, and Future

    Energy Technology Data Exchange (ETDEWEB)

    Waters, Dean

    2004-09-15

    The art of gas centrifugation was born in 1935 at the University of Virginia when Dr. Jesse Beams demonstrated experimentally the separation of chlorine isotopes using an ultra-high speed centrifuge. Dr. Beam’s experiment initiated work that created a rich history of scientific and engineering accomplishment in the United States in the art of isotope separation and even large scale biological separation by centrifugation. The early history of the gas centrifuge development was captured in a lecture and documented by Dr. Jesse Beams in 1975. Much of Dr. Beams lecture material is used in this paper up to the year 1960. Following work by Dr. Gernot Zippe at the University of Virginia between 1958 and 1960, the US government embarked on a centrifuge development program that ultimately led to the start of construction of the Gas Centrifuge Enrichment Plant in Piketon Ohio in the late 1970’s. The government program was abandoned in 1985 after investing in the construction of two of six planned process buildings, a complete supply chain for process and centrifuge parts, and the successful manufacture and brief operation of an initial complement of production machines that would have met 15 percent of the planned capacity of the constructed process buildings. A declining market for enriched uranium, a glut of uranium enrichment capacity worldwide, and the promise of a new laser based separation process factored in the decision to stop the government program. By the late 1990’s it had become evident that gas centrifugation held the best promise to produce enriched uranium at low cost. In1999, the United States Enrichment Corporation undertook an initiative to revive the best of the American centrifuge technology that had been abandoned fourteen years earlier. This is an exciting story and one that when complete will enable the United States to maintain its domestic supply and to be highly competitive in the world market for this important energy commodity. (auth)

  3. On the partition dimension of unicyclic graphs

    CERN Document Server

    Rodriguez-Velazquez, Juan A; Fernau, Henning

    2011-01-01

    Given an ordered partition $\\Pi =\\{P_1,P_2, ...,P_t\\}$ of the vertex set $V$ of a connected graph $G=(V,E)$, the \\emph{partition representation} of a vertex $v\\in V$ with respect to the partition $\\Pi$ is the vector $r(v|\\Pi)=(d(v,P_1),d(v,P_2),...,d(v,P_t))$, where $d(v,P_i)$ represents the distance between the vertex $v$ and the set $P_i$. A partition $\\Pi$ of $V$ is a \\emph{resolving partition} if different vertices of $G$ have different partition representations, i.e., for every pair of vertices $u,v\\in V$, $r(u|\\Pi)\

  4. On the partition dimension of trees

    CERN Document Server

    Rodriguez-Velazquez, Juan A; Lemanska, Magdalena

    2011-01-01

    Given an ordered partition $\\Pi =\\{P_1,P_2, ...,P_t\\}$ of the vertex set $V$ of a connected graph $G=(V,E)$, the \\emph{partition representation} of a vertex $v\\in V$ with respect to the partition $\\Pi$ is the vector $r(v|\\Pi)=(d(v,P_1),d(v,P_2),...,d(v,P_t))$, where $d(v,P_i)$ represents the distance between the vertex $v$ and the set $P_i$. A partition $\\Pi$ of $V$ is a \\emph{resolving partition} of $G$ if different vertices of $G$ have different partition representations, i.e., for every pair of vertices $u,v\\in V$, $r(u|\\Pi)\

  5. Separation of Nanoparticles in Aqueous Multiphase Systems through Centrifugation

    KAUST Repository

    Akbulut, Ozge

    2012-08-08

    This paper demonstrates the use of aqueous multiphase systems (MuPSs) as media for rate-zonal centrifugation to separate nanoparticles of different shapes and sizes. The properties of MuPSs do not change with time or during centrifugation; this stability facilitates sample collection after separation. A three-phase system demonstrates the separation of the reaction products (nanorods, nanospheres, and large particles) of a synthesis of gold nanorods, and enriches the nanorods from 48 to 99% in less than ten minutes using a benchtop centrifuge. © 2012 American Chemical Society.

  6. Evolution of Task Partitioning in Swarm Robotics

    OpenAIRE

    Ferrante, Eliseo,; Duenez-Guzman, E.; Turgut, A. E.; Wenseleers, Tom

    2013-01-01

    International audience; Task-partitioning refers to the process whereby a task is divided into two or more sub-tasks. Through task partitioning both efficiency and effectiveness can be improved provided the right environmental conditions. We synthesize self-organized task partitioning behaviors for a swarm of mobile robots using artificial evolution. Through validation experiments, we show that the synthesized behaviors exploits behavioral specialization despite being based on homogeneous ind...

  7. Data Partitioning View of Mining Big Data

    OpenAIRE

    Zhang, Shichao

    2016-01-01

    There are two main approximations of mining big data in memory. One is to partition a big dataset to several subsets, so as to mine each subset in memory. By this way, global patterns can be obtained by synthesizing all local patterns discovered from these subsets. Another is the statistical sampling method. This indicates that data partitioning should be an important strategy for mining big data. This paper recalls our work on mining big data with a data partitioning and shows some interesti...

  8. Hardware/software partitioning in Verilog.

    OpenAIRE

    2002-01-01

    We propose in this paper an algebraic approach to hardware/software partitioning in Verilog HDL. We explore a collection of algebraic laws for Verilog programs, from which we design a set of syntax-based algebraic rules to conduct hardware/software partitioning. The co-specification language and the target hardware and software description languages are specific subsets of Verilog, which brings forth our successful verification for the correctness of the partitioning process by algebra of Ver...

  9. Simultaneous determination of 17 sulfonamides and the potentiators ormetoprim and trimethoprim in salmon muscle by liquid chromatography with tandem mass spectrometry detection.

    Science.gov (United States)

    Potter, Ross A; Burns, B Garth; van de Riet, Jeffrey M; North, David H; Darvesh, Rozina

    2007-01-01

    A simple, robust method using liquid chromatography/tandem mass spectrometry (LC/MS/MS) for the simultaneous determination of 17 sulfonamides [sulfanilamide (SNL), sulfacetamide (SAA), sulfaguanidine (SGD), sulfapyridine (SPY), sulfadiazine (SDZ), sulfathiazole (STZ), sulfamerazine (SMR), sulfamethoxazole (SOZ), sulfamoxole (SXL), sulfisoxazole (SXZ), sulfamethizole (SML), sulfamethazine (SMZ), sulfamethoxypyridazine (SMP), sulfamonomethoxine (SMM), sulfachloropyridazine (SCP), sulfaquinoxaline (SQX), and sulfadimethoxine (SDM)] and 2 potentiators [ormetoprim (OMP) and trimethoprim (TMP)] in fish tissue has been developed. The analytes were extracted from homogenized fish tissue with water-acetonitrile (50 + 50). The extract was clarified by centrifugation and a portion defatted with hexane. The analytes were partitioned into chloroform and evaporated to dryness. The redissolved residue was applied to a C18 reversed-phase column with a water-acetonitrile (0.1% acetic acid) gradient. All of the compounds were completely separated and detected in TMP to approximately 30% for SAA. Relative standard deviations for repeat analysis varied from 4% for SMZ and SCP to 23% for SAA.

  10. Determination of trihalomethanes in soil matrices by simplified quick, easy, cheap, effective, rugged and safe extraction and fast gas chromatography with electron capture detection.

    Science.gov (United States)

    Herrero Martín, Sara; García Pinto, Carmelo; Pérez Pavón, José Luis; Moreno Cordero, Bernardo

    2010-07-23

    A method based on QuEChERS extraction is proposed for the determination of trihalomethanes (chloroform, bromodichloromethane, dibromocloromethane and bromoform) in soil samples. The new version of QuEChERS adapted to soil samples consists of liquid extraction with ethyl acetate, the addition of water to moisten the samples, salting-out partitioning of the water with anhydrous MgSO4, and direct injection of the organic extract, obtained after the centrifugation step, into the gas chromatograph. This simplified extraction procedure maintains the advantages of the original method and avoids some steps, making the final procedure simpler, faster, and cheaper, with the consequent reduction in errors associated with sample manipulation. The experimental conditions of the analytical method, based on fast gas chromatography (FGC) and micro-electron capture detection (microECD), were optimized. The column and oven program used allowed fast separation of the compounds in less than 4 min and the total analysis cycle time was as short as 10 min. The existence of a matrix effect was checked and the analytical conditions of the method were studied in a fortified garden soil sample. The highly sensitive and selective detector used afforded to detection limits in the order of ng/kg for the target compounds. To validate the proposed method two certified reference materials (CRMs) were analyzed.

  11. Instrumentation: Ion Chromatography.

    Science.gov (United States)

    Fritz, James S.

    1987-01-01

    Discusses the importance of ion chromatography in separating and measuring anions. The principles of ion exchange are presented, along with some applications of ion chromatography in industry. Ion chromatography systems are described, as well as ion pair and ion exclusion chromatography, column packings, detectors, and programming. (TW)

  12. Analysis of alcohol dehydrogenase inhibitors from Desmodium styracifolium using centrifugal ultrafiltration coupled with HPLC-MS

    Directory of Open Access Journals (Sweden)

    Liu Liangliang

    2015-01-01

    Full Text Available Alcohol dehydrogenase (ADH inhibitors play an important role in the treatment of human methanol or ethylene glycol poisoning and the suppression of acetaldehyde accumulation in alcoholics. In this study, centrifugal ultrafiltration coupled with high performance liquid chromatography-mass spectrometry (HPLC-MS was utilized to screen and identify ADH inhibitors from ethyl acetate extract of Desmosium styracifolium (Osb. Merr. The experiment conditions of centrifugal ultrafiltration were optimized. At the optimum conditions (ADH concentration: 37.5 μg mL-1, incubation time: 90 min, pH: 7.0 and temperature: 15°C, formononetin and aromadendrin were successfully screened and identified from ethyl acetate extract of Desmodium styracifolium. The screening result was verified by ADH inhibition assays. The IC50 values of formononetin and aromadendrin were 70.8 and 84.7 μg mL-1, which were accorded with the binding degrees of them. Aromadendrin was first reported to have inhibitory activity on ADH. This method provided an effective way to screen active compounds from natural products.

  13. Combinatorial set theory partition relations for cardinals

    CERN Document Server

    Erdös, P; Hajnal, A; Rado, P

    2011-01-01

    This work presents the most important combinatorial ideas in partition calculus and discusses ordinary partition relations for cardinals without the assumption of the generalized continuum hypothesis. A separate section of the book describes the main partition symbols scattered in the literature. A chapter on the applications of the combinatorial methods in partition calculus includes a section on topology with Arhangel''skii''s famous result that a first countable compact Hausdorff space has cardinality, at most continuum. Several sections on set mappings are included as well as an account of

  14. Failure analysis of a polymer centrifugal impeller

    Directory of Open Access Journals (Sweden)

    Nikhil K. Kar

    2015-10-01

    Full Text Available A failure analysis investigation was performed on a fractured polymer impeller used in a respiratory blower. Light microscopy, scanning electron microscopy and finite element analysis techniques were utilized to characterize the mode(s of failure and fracture surfaces. A radial split down the impeller center was observed with symmetric fracture faces about the impeller bore. Fractographic analysis revealed brittle fracture features including Wallner lines, mirror, mist and hackle features stemming from the impeller bore, emanating radially outward. Crazed fibrils and faint fatigue striations suggest that intermittent load cycling led to initiation, and rapid propagation of multiple crack fronts originating along the impeller lip. Finite element analysis revealed a flexural condition induces localized stresses along the impeller lip. Significant wear features were also observed within the impeller bore, which may have contributed to premature failure of the impeller. The brittle fracture morphology and defects within the impeller bore suggest that premature failure occurred because of multiple interacting factors including: intermittently high centrifugal velocities, imbalance bore and shaft conditions, defects within the bore caused by machining, and stress concentrations along the circumference of the impeller lip.

  15. Central centrifugal cicatricial alopecia: challenges and solutions

    Directory of Open Access Journals (Sweden)

    Herskovitz I

    2016-08-01

    Full Text Available Ingrid Herskovitz, Mariya Miteva Department of Dermatology and Cutaneous Surgery, University of Miami L Miller School of Medicine, Miami, FL, USA Abstract: Central centrifugal cicatricial alopecia (CCCA is the most common scarring alopecia among African American women. Data about epidemiology, etiology, genetic inheritance, and management are scarce and come from individual reports or small series. CCCA has been associated with hot combing and traumatic hair styling for years; however, studies fail to confirm it as the sole etiologic factor. It has been shown in a small series that CCCA can be inherited in an autosomal dominant fashion, with a partial penetrance and a strong modifying effect of hairstyling and sex. CCCA presents clinically as a central area of progressive irreversible hair loss that expands to the periphery. A patchy form has also been described. Dermoscopy is helpful to identify the optimal site for the biopsy, which establishes the diagnosis. Well-designed randomized controlled trials are needed to discover the optimal management. At this point, patients are advised to avoid traction and chemical treatments; topical and intralesional steroids, calcineurin inhibitors, and minoxidil can be helpful in halting the progression. Keywords: hair loss, alopecia, dermatoscopy, dermoscopy, trichoscopy, black scalp, African American, scarring alopecia

  16. Central centrifugal cicatricial alopecia: challenges and solutions.

    Science.gov (United States)

    Herskovitz, Ingrid; Miteva, Mariya

    2016-01-01

    Central centrifugal cicatricial alopecia (CCCA) is the most common scarring alopecia among African American women. Data about epidemiology, etiology, genetic inheritance, and management are scarce and come from individual reports or small series. CCCA has been associated with hot combing and traumatic hair styling for years; however, studies fail to confirm it as the sole etiologic factor. It has been shown in a small series that CCCA can be inherited in an autosomal dominant fashion, with a partial penetrance and a strong modifying effect of hairstyling and sex. CCCA presents clinically as a central area of progressive irreversible hair loss that expands to the periphery. A patchy form has also been described. Dermoscopy is helpful to identify the optimal site for the biopsy, which establishes the diagnosis. Well-designed randomized controlled trials are needed to discover the optimal management. At this point, patients are advised to avoid traction and chemical treatments; topical and intralesional steroids, calcineurin inhibitors, and minoxidil can be helpful in halting the progression.

  17. Centrifuging Step-Screw Conveyor for Regolith Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A variety of ISRU operations will utilize lunar regolith as feedstock. The proposed centrifuging step-screw conveyor concept will provide a well controlled robust,...

  18. MULTIOBJECT OPTIMIZATION OF A CENTRIFUGAL IMPELLER USING EVOLUTIONARY ALGORITHMS

    Institute of Scientific and Technical Information of China (English)

    Li Jun; Liu Lijun; Feng Zhenping

    2004-01-01

    Application of the multiobjective evolutionary algorithms to the aerodynamic optimization design of a centrifugal impeller is presented. The aerodynamic performance of a centrifugal impeller is evaluated by using the three-dimensional Navier-Stokes solutions. The typical centrifugal impeller is redesigned for maximization of the pressure rise and blade load and minimization of the rotational total pressure loss at the given flow conditions. The B閦ier curves are used to parameterize the three-dimensional impeller blade shape. The present method obtains many reasonable Pareto optimal designs that outperform the original centrifugal impeller. Detailed observation of the certain Pareto optimal design demonstrates the feasibility of the present multiobjective optimization method tool for turbomachinery design.

  19. TECHNOLOGY EVALUATION REPORT: RETECH'S PLASMA CENTRIFUGAL FURNACE - VOLUME I

    Science.gov (United States)

    A demonstration of the Retech, Inc. Plasma Centrifugal Furnace (PCF) was conducted under the Superfund Innovative Technology Evaluation (SITE) Program at the Department of Energy's (DOE's) Component Development and Integration Facility in Butte, Montana. The furnace uses heat gen...

  20. Comparative analysis of discrete exosome fractions obtained by differential centrifugation

    DEFF Research Database (Denmark)

    Jeppesen, Dennis Kjølhede; Hvam, Michael L; Primdahl-Bengtson, Bjarke

    2014-01-01

    BACKGROUND: Cells release a mixture of extracellular vesicles, amongst these exosomes, that differ in size, density and composition. The standard isolation method for exosomes is centrifugation of fluid samples, typically at 100,000×g or above. Knowledge of the effect of discrete...... ultracentrifugation speeds on the purification from different cell types, however, is limited. METHODS: We examined the effect of applying differential centrifugation g-forces ranging from 33,000×g to 200,000×g on exosome yield and purity, using 2 unrelated human cell lines, embryonic kidney HEK293 cells and bladder...... of phenol red and cleared by 200,000×g overnight centrifugation. The centrifugation tube fill level impacted the sedimentation efficacy. Comparative analysis by NTA, protein quantification, and detection of exosomal and contamination markers identified differences in vesicle size, concentration...

  1. Confusion around the tidal force and the centrifugal force

    CERN Document Server

    Matsuda, Takuya; Boffin, Henri M J

    2015-01-01

    We discuss the tidal force, whose notion is sometimes misunderstood in the public domain literature. We discuss the tidal force exerted by a secondary point mass on an extended primary body such as the Earth. The tidal force arises because the gravitational force exerted on the extended body by the secondary mass is not uniform across the primary. In the derivation of the tidal force, the non-uniformity of the gravity is essential, and inertial forces such as the centrifugal force are not needed. Nevertheless, it is often asserted that the tidal force can be explained by the centrifugal force. If we literally take into account the centrifugal force, it would mislead us. We therefore also discuss the proper treatment of the centrifugal force.

  2. Manufacture of hollow ingots using centrifugal casting machines

    Science.gov (United States)

    Pomeshchikov, A. G.; Greneva, T. S.; Baidachenko, V. I.; Berezin, V. I.

    2010-12-01

    Centrifugal machines are proposed for the foundry created at the Almalyk Mining and Smelting Factory in order to produce hollow ingots of a liquid metal made by remelting of consumable electrodes in a refractory accumulating crucible.

  3. DESIGN AND FABRICATION OF A CENTRIFUGAL CASTING MACHINE

    Directory of Open Access Journals (Sweden)

    Adedipe Oyewole

    2011-12-01

    Full Text Available The design and fabrication of a centrifugal casting machine was successfully carried out. The operation of the machine was based on the principle of centrifugal force. Suitable design theory, analysis and calculation were adopted carried out in the course of the work. The mold is bolted to the base plate which can rotate at moderatespeeds thereby forcing the molten metal against the inner walls of the mold. This machine could be used to cast small engineering components. The centrifugal force on the machine was determined to be 3207.3N, while the required power on the machine was 854.7W. A test was carried out on the fabricated centrifugal casting machine with aluminum alloy and the machine was able to cast 6kg of aluminum alloy and the casting was successful.

  4. Fluent-based numerical simulation of flow centrifugal fan

    Institute of Scientific and Technical Information of China (English)

    LI Xian-zhang

    2011-01-01

    Testing centrifugal fan flow field by physical laboratory is difficult because the testing system is complex and the workload is heavy, and the results observed by naked-eye deviates far from the actual value. To address this problem, the computational fluid dynamics software FLUENT was applied to establish three-dimensional model of the centrifugal fan. The numeral model was verified by comparing simulation data to experimental data. The pressure centrifugal fan and the speed changes in distribution in centrifugal fan was simulated by computational fluid dynamics software FLUENT. The simulation results show that the gas flow velocity in the impeller increases with impeller radius increase. Static pressure gradually increases when gas from the fan access is imported through fan impeller leaving fans.

  5. 21 CFR 862.2140 - Centrifugal chemistry analyzer for clinical use.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Centrifugal chemistry analyzer for clinical use... Instruments § 862.2140 Centrifugal chemistry analyzer for clinical use. (a) Identification. A centrifugal chemistry analyzer for clinical use is an automatic device intended to centrifugally mix a sample and...

  6. Rapid detection of simulated bacteremia by centrifugation and filtration.

    OpenAIRE

    Herlich, M B; Schell, R F; Francisco, M.; Le Frock, J L

    1982-01-01

    A centrifugation-filtration procedure was developed to expedite the recovery of microorganisms from blood. Fresh whole human blood was inoculated with various aerobic and facultatively anaerobic microorganisms (3 to 18 per ml). The seeded blood was carefully overlaid on a Ficoll-Hypaque gradient (density, 1.114 g/ml) and centrifuged (400 x g) for 45 min at ambient temperature. The entire gradient (plasma, leukocytes, and Ficoll-Hypaque) was removed and filtered through a 0.22-micrometer membr...

  7. CALCULATION AND IMPROVEMENT OF DYNAMIC CHARACTERISTICS OF CENTRIFUGE

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The modeling of the rotor-support system of a typical centrifuge is discussed. The impedance matching method, cooperating with Riccati transfer matrix method and modal analysis method are adopted to calculate its dynamic characteristics. The influences of the main parts to the critical speeds are analyzed. Based on the analysis, a critical speed in the operating speed range is tuned successfully, and thus the dynamic characteristics of the centrifuge are much improved.

  8. Synthesis and Analytical Centrifugation of Magnetic Model Colloids

    OpenAIRE

    Luigjes, B.

    2012-01-01

    This thesis is a study of the preparation and thermodynamic properties of magnetic colloids. First, two types of magnetic model colloids are investigated: composite colloids and single-domain nanoparticles. Thermodynamics of magnetic colloids is studied using analytical centrifugation, including a specially adapted centrifuge for measuring heavy and strongly light absorbing colloids. Magnetic composite colloids can be prepared from thermodynamically stable Pickering emulsions of 3-methacrylox...

  9. Centrifugal microfluidic platforms: advanced unit operations and applications.

    Science.gov (United States)

    Strohmeier, O; Keller, M; Schwemmer, F; Zehnle, S; Mark, D; von Stetten, F; Zengerle, R; Paust, N

    2015-10-01

    Centrifugal microfluidics has evolved into a mature technology. Several major diagnostic companies either have products on the market or are currently evaluating centrifugal microfluidics for product development. The fields of application are widespread and include clinical chemistry, immunodiagnostics and protein analysis, cell handling, molecular diagnostics, as well as food, water, and soil analysis. Nevertheless, new fluidic functions and applications that expand the possibilities of centrifugal microfluidics are being introduced at a high pace. In this review, we first present an up-to-date comprehensive overview of centrifugal microfluidic unit operations. Then, we introduce the term "process chain" to review how these unit operations can be combined for the automation of laboratory workflows. Such aggregation of basic functionalities enables efficient fluidic design at a higher level of integration. Furthermore, we analyze how novel, ground-breaking unit operations may foster the integration of more complex applications. Among these are the storage of pneumatic energy to realize complex switching sequences or to pump liquids radially inward, as well as the complete pre-storage and release of reagents. In this context, centrifugal microfluidics provides major advantages over other microfluidic actuation principles: the pulse-free inertial liquid propulsion provided by centrifugal microfluidics allows for closed fluidic systems that are free of any interfaces to external pumps. Processed volumes are easily scalable from nanoliters to milliliters. Volume forces can be adjusted by rotation and thus, even for very small volumes, surface forces may easily be overcome in the centrifugal gravity field which enables the efficient separation of nanoliter volumes from channels, chambers or sensor matrixes as well as the removal of any disturbing bubbles. In summary, centrifugal microfluidics takes advantage of a comprehensive set of fluidic unit operations such as

  10. Parameter Study of Melt Spun Polypropylene Fibers by Centrifugal Spinning

    Science.gov (United States)

    2014-07-01

    synthesis of C/Fe3O4 composite nanofibers and their application for high performance lithium-ion batteries . J Power Sources. 2008;83:717–723. 2. Zhang...spinning process . Eur Polym J. 2013;49:3834–3845. 9 1 DEFENSE TECHNICAL (PDF) INFORMATION CTR DTIC OCA 2 DIRECTOR (PDF) US ARMY RESEARCH...composites, and energy harvesting to tissue engineering and drug delivery. Centrifugal spinning is a new technique that uses centrifugal forces to form

  11. Design and Characterization of a Centrifugal Compressor Surge Test Rig

    OpenAIRE

    2011-01-01

    A detailed description of a new centrifugal compressor surge test rig is presented. The objective of the design and development of the rig is to study the surge phenomenon in centrifugal compression systems and to investigate a novel method of surge control by active magnetic bearing servo actuation of the impeller axial tip clearance. In this paper, we focus on the design, initial setup, and testing of the rig. The latter two include the commissioning of the rig and the experimental characte...

  12. AM(VI) partitioning studies. FY14 final report

    Energy Technology Data Exchange (ETDEWEB)

    Mincher, Bruce J. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2014-10-01

    The use of higher oxidation states of americium in partitioning from the lanthanides is under continued investigation by the sigma team. This is based on the hypothesis that Am(VI) can be produced and remain stable in irradiated first cycle raffinate solution long enough to perform solvent extraction for separations. The stability of Am(VI) to autoreduction was measured using millimolar americium concentrations in a 1-cm cell with a Cary 6000 UV/Vis spectrophotometer for data acquisition. At millimolar americium concentrations, Am(VI) is stable enough against its own autoreduction for separations purposes. A second major accomplishment during FY14 was the hot test. Americium oxidation and extraction was performed using a centrifugal contactor-based test bed consisting of an extraction stage and two stripping stages. Sixty-three percent americium extraction was obtained in one extraction stage, in agreement with batch contacts. Promising electrochemical oxidation results have also been obtained, using terpyridine ligand derivatized electrodes for binding of Am(III). Approximately 50 % of the Am(III) was oxidized to Am(V) over the course of 1 hour. It is believed that this is the first demonstration of the electrolytic oxidation of americium in a non-complexing solution. Finally, an initial investigation of Am(VI) extraction using diethylhexylbutyramide (DEHBA) was performed.

  13. HPAM: Hirshfeld partitioned atomic multipoles

    Science.gov (United States)

    Elking, Dennis M.; Perera, Lalith; Pedersen, Lee G.

    2012-02-01

    An implementation of the Hirshfeld (HD) and Hirshfeld-Iterated (HD-I) atomic charge density partitioning schemes is described. Atomic charges and atomic multipoles are calculated from the HD and HD-I atomic charge densities for arbitrary atomic multipole rank l on molecules of arbitrary shape and size. The HD and HD-I atomic charges/multipoles are tested by comparing molecular multipole moments and the electrostatic potential (ESP) surrounding a molecule with their reference ab initio values. In general, the HD-I atomic charges/multipoles are found to better reproduce ab initio electrostatic properties over HD atomic charges/multipoles. A systematic increase in precision for reproducing ab initio electrostatic properties is demonstrated by increasing the atomic multipole rank from l=0 (atomic charges) to l=4 (atomic hexadecapoles). Both HD and HD-I atomic multipoles up to rank l are shown to exactly reproduce ab initio molecular multipole moments of rank L for L⩽l. In addition, molecular dipole moments calculated by HD, HD-I, and ChelpG atomic charges only ( l=0) are compared with reference ab initio values. Significant errors in reproducing ab initio molecular dipole moments are found if only HD or HD-I atomic charges used. Program summaryProgram title: HPAM Catalogue identifier: AEKP_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEKP_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: GNU General Public License v2 No. of lines in distributed program, including test data, etc.: 500 809 No. of bytes in distributed program, including test data, etc.: 13 424 494 Distribution format: tar.gz Programming language: C Computer: Any Operating system: Linux RAM: Typically, a few hundred megabytes Classification: 16.13 External routines: The program requires 'formatted checkpoint' files obtained from the Gaussian 03 or Gaussian 09 quantum chemistry program. Nature of problem: An ab initio

  14. Partition functions for supersymmetric black holes

    NARCIS (Netherlands)

    Manschot, J.

    2008-01-01

    This thesis presents a number of results on partition functions for four-dimensional supersymmetric black holes. These partition functions are important tools to explain the entropy of black holes from a microscopic point of view. Such a microscopic explanation was desired after the association of a

  15. Partitioning of resveratrol between pentane and DMSO

    DEFF Research Database (Denmark)

    Shen, Chen; Stein, Paul C.; Klösgen-Buchkremer, Beate Maria

    2015-01-01

    Partitioning of trans-3,5,4′-trihydroxy-stilbene (resveratrol) between n-pentane and DMSO was investigated as a contribution to understand the interaction between resveratrol and biomembranes. In order to determine the partition coefficient P* of resveratrol between pentane and DMSO, resveratrol ...

  16. Graph Partitioning Models for Parallel Computing

    Energy Technology Data Exchange (ETDEWEB)

    Hendrickson, B.; Kolda, T.G.

    1999-03-02

    Calculations can naturally be described as graphs in which vertices represent computation and edges reflect data dependencies. By partitioning the vertices of a graph, the calculation can be divided among processors of a parallel computer. However, the standard methodology for graph partitioning minimizes the wrong metric and lacks expressibility. We survey several recently proposed alternatives and discuss their relative merits.

  17. Crossings and nestings in colored set partitions

    CERN Document Server

    Marberg, Eric

    2012-01-01

    Several years ago, Chen, Deng, Du, Stanley, and Yan introduced the notion of $k$-crossings and $k$-nestings for set partitions, and proved that the sizes of the largest $k$-crossings and $k$-nestings in the partitions of an $n$-set possess a symmetric joint distribution. The present work extends these results to $r$-colored set partitions, by which we mean set partitions whose arcs are labeled by an $r$-element set. A $k$-crossing or $k$-nesting in this context is a sequence or arcs, all with the same color, which form a $k$-crossing or $k$-nesting in the usual sense. To prove our extension, we produce a bijection from $r$-colored set partitions to certain sequences of $r$-partite partitions, which in the uncolored case specializes to a novel description of the map from set partitions to vacillating tableaux given by Chen et al. Among other applications, we explain how our construction implies recent results of Chen and Guo on colored matchings, and also an analogous symmetric joint distribution of crossings ...

  18. [On the partition of acupuncture academic schools].

    Science.gov (United States)

    Yang, Pengyan; Luo, Xi; Xia, Youbing

    2016-05-01

    Nowadays extensive attention has been paid on the research of acupuncture academic schools, however, a widely accepted method of partition of acupuncture academic schools is still in need. In this paper, the methods of partition of acupuncture academic schools in the history have been arranged, and three typical methods of"partition of five schools" "partition of eighteen schools" and "two-stage based partition" are summarized. After adeep analysis on the disadvantages and advantages of these three methods, a new method of partition of acupuncture academic schools that is called "three-stage based partition" is proposed. In this method, after the overall acupuncture academic schools are divided into an ancient stage, a modern stage and a contemporary stage, each schoolis divided into its sub-school category. It is believed that this method of partition can remedy the weaknesses ofcurrent methods, but also explore a new model of inheritance and development under a different aspect through thedifferentiation and interaction of acupuncture academic schools at three stages.

  19. Fabrication of Al/Diamond Particles Functionally Graded Materials by Centrifugal Sintered-Casting Method

    Science.gov (United States)

    Watanabe, Yoshimi; Shibuya, Masafumi; Sato, Hisashi

    2013-03-01

    The continuous graded structure of functionally graded materials (FGMs) can be created under a centrifugal force. Centrifugal sintered-casting (CSC) method, proposed by the authors, is one of the fabrication methods of FGM under centrifugal force. This method is a combination of the centrifugal sintering method and centrifugal casting method. In this study, Al/diamond particle FGM was fabricated by the proposed method.

  20. Demonstration of a crown ether process for partitioning strontium from high level liquid waste (HLLW)

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Jianchen; Jing, Shan; Chen, Jing [Tsinghua Univ., Beijing (China). Inst. of Nuclear and New Energy Technology (INET); Tsinghua Univ., Beijing (China). Beijing Key Lab of Radioactive Waste Treatment

    2016-05-01

    Chinese HLLW with a higher-salt liquid that was generated via plutonium uranium recovery by extraction (PUREX) processing was temporarily stored in stainless steel tanks and is waiting for treatment. The volume and heat-loading of the glass block are reduced if the strontium, cesium, actinides and other long-life radioactive elements, such as Tc in the HLLW, are partitioned before the HLLW verification. This process is beneficial to preserve the capacity of the geological disposal repository and to minimize long-term hazards. The process of partitioning strontium from Chinese HLLW using Dicyclohexano-18Crown-6(DCH18C-6) was developed in past decades, including such fundamental studies as the small scale cold and hot test. In this work, new studies are introduced, including the cold and the long time hot cascade tests, using a miniature centrifugal contactor set and the pilot-scale cold test using pulse extraction columns. The results indicate that the crown process is promising for partitioning strontium from Chinese HLLW.

  1. Basic Principles of Chromatography

    Science.gov (United States)

    Ismail, Baraem; Nielsen, S. Suzanne

    Chromatography has a great impact on all areas of analysis and, therefore, on the progress of science in general. Chromatography differs from other methods of separation in that a wide variety of materials, equipment, and techniques can be used. [Readers are referred to references (1-19) for general and specific information on chromatography.]. This chapter will focus on the principles of chromatography, mainly liquid chromatography (LC). Detailed principles and applications of gas chromatography (GC) will be discussed in Chap. 29. In view of its widespread use and applications, high-performance liquid chromatography (HPLC) will be discussed in a separate chapter (Chap. 28). The general principles of extraction are first described as a basis for understanding chromatography.

  2. DYNAMIC TASK PARTITIONING MODEL IN PARALLEL COMPUTING

    Directory of Open Access Journals (Sweden)

    Javed Ali

    2012-04-01

    Full Text Available Parallel computing systems compose task partitioning strategies in a true multiprocessing manner. Such systems share the algorithm and processing unit as computing resources which leads to highly inter process communications capabilities. The main part of the proposed algorithm is resource management unit which performs task partitioning and co-scheduling .In this paper, we present a technique for integrated task partitioning and co-scheduling on the privately owned network. We focus on real-time and non preemptive systems. A large variety of experiments have been conducted on the proposed algorithm using synthetic and real tasks. Goal of computation model is to provide a realistic representation of the costs of programming The results show the benefit of the task partitioning. The main characteristics of our method are optimal scheduling and strong link between partitioning, scheduling and communication. Some important models for task partitioning are also discussed in the paper. We target the algorithm for task partitioning which improve the inter process communication between the tasks and use the recourses of the system in the efficient manner. The proposed algorithm contributes the inter-process communication cost minimization amongst the executing processes.

  3. Reinforcement learning with partitioning function system

    Institute of Scientific and Technical Information of China (English)

    李伟; 叶庆泰; 朱昌明

    2004-01-01

    The size of state-space is the limiting factor in applying reinforcement learning algorithms to practical cases. A reinforcement learning system with partitioning function (RLWPF) is established, in which statespace is partitioned into several regions. Inside the performance principle of RLWPF is based on a Semi-Markov decision process and has general significance. It can be applied to any reinforcement learning with a large statespace. In RLWPF, the partitioning module dispatches agents into different regions in order to decrease the state-space of each agent. This article proves the convergence of the SARSA algorithm for a Semi-Markov decision process, ensuring the convergence of RLWPF by analyzing the equivalence of two value functions in two Semi-Markov decision processes before and after partitioning. This article can show that the optimal policy learned by RLWPF is consistent with prior domain knowledge. An elevator group system is devised to decrease the average waiting time of passengers. Four agents control four elevator cars respectively. Based on RLWPF, a partitioning module is developed through defining a uniform round trip time as the partitioning criteria, making the wait time of most passengers more or less identical then elevator cars should only answer hall calls in their own region. Compared with ordinary elevator systems and reinforcement learning systems without partitioning module, the performance results show the advantage of RLWPF.

  4. Aqueous two-phase partition applied to the isolation of plasma membranes and Golgi apparatus from cultured mammalian cells

    Science.gov (United States)

    Morre, D. M.; Morre, D. J.

    2000-01-01

    Partitioning in dextran-poly(ethylene)glycol (PEG) aqueous-aqueous phase systems represents a mature technology with many applications to separations of cells and to the preparation of membranes from mammalian cells. Most applications to membrane isolation and purification have focused on plasma membranes, plasma membrane domains and separation of right side-out and inside-out plasma membrane vesicles. The method exploits a combination of membrane properties, including charge and hydrophobicity. Purification is based upon differential distributions of the constituents in a sample between the two principal compartments of the two phases (upper and lower) and at the interface. The order of affinity of animal cell membranes for the upper phase is: endoplasmic reticulum Golgi apparatusGolgi apparatus from transformed mammalian cells that combines aqueous two-phase partition and centrifugation. Also described is a periodic NADH oxidase, a new enzyme marker for right side-out plasma membrane vesicles not requiring detergent disruptions for measurement of activity.

  5. Partial domain wall partition functions

    CERN Document Server

    Foda, O

    2012-01-01

    We consider six-vertex model configurations on a rectangular lattice with n (N) horizontal (vertical) lines, and "partial domain wall boundary conditions" defined as 1. all 2n arrows on the left and right boundaries point inwards, 2. n_u (n_l) arrows on the upper (lower) boundary, such that n_u + n_l = N - n, also point inwards, 3. all remaining n+N arrows on the upper and lower boundaries point outwards, and 4. all spin configurations on the upper and lower boundaries are summed over. To generate (n-by-N) "partial domain wall configurations", one can start from A. (N-by-N) configurations with domain wall boundary conditions and delete n_u (n_l) upper (lower) horizontal lines, or B. (2n-by-N) configurations that represent the scalar product of an n-magnon Bethe eigenstate and an n-magnon generic state on an N-site spin-1/2 chain, and delete the n lines that represent the Bethe eigenstate. The corresponding "partial domain wall partition function" is computed in construction {A} ({B}) as an N-by-N (n-by-n) det...

  6. Energy partitioning schemes: a dilemma.

    Science.gov (United States)

    Mayer, I

    2007-01-01

    Two closely related energy partitioning schemes, in which the total energy is presented as a sum of atomic and diatomic contributions by using the "atomic decomposition of identity", are compared on the example of N,N-dimethylformamide, a simple but chemically rich molecule. Both schemes account for different intramolecular interactions, for instance they identify the weak C-H...O intramolecular interactions, but give completely different numbers. (The energy decomposition scheme based on the virial theorem is also considered.) The comparison of the two schemes resulted in a dilemma which is especially striking when these schemes are applied for molecules distorted from their equilibrium structures: one either gets numbers which are "on the chemical scale" and have quite appealing values at the equilibrium molecular geometries, but exhibiting a counter-intuitive distance dependence (the two-center energy components increase in absolute value with the increase of the interatomic distances)--or numbers with too large absolute values but "correct" distance behaviour. The problem is connected with the quick decay of the diatomic kinetic energy components.

  7. Jucys-Murphy elements for partition algebras

    CERN Document Server

    Enyang, John

    2010-01-01

    An inductive formula is given for a family of elements which are shown to play a role in the partition algebras which is analogous to the part played by classical Jucys-Murphy elements in the symmetric group. Using Schur-Weyl duality it is shown that the aforementioned inductive definition is equivalent to the combinatorial definition given by Halverson and Ram for Jucys-Murphy elements of partition algebras. As a consequence of the inductive formula for Jucys-Murphy elements, a new presentation for partition algebras in terms of certain involutions is also derived.

  8. An Algebraic Hardware/Software Partitioning Algorithm

    Institute of Scientific and Technical Information of China (English)

    秦胜潮; 何积丰; 裘宗燕; 张乃孝

    2002-01-01

    Hardware and software co-design is a design technique which delivers computer systems comprising hardware and software components. A critical phase of the co-design process is to decompose a program into hardware and software. This paper proposes an algebraic partitioning algorithm whose correctness is verified in program algebra. The authors introduce a program analysis phase before program partitioning and develop a collection of syntax-based splitting rules. The former provides the information for moving operations from software to hardware and reducing the interaction between components, and the latter supports a compositional approach to program partitioning.

  9. PARTITION PROPERTY OF DOMAIN DECOMPOSITION WITHOUT ELLIPTICITY

    Institute of Scientific and Technical Information of China (English)

    Mo Mu; Yun-qing Huang

    2001-01-01

    Partition property plays a central role in domain decomposition methods. Existing theory essentially assumes certain ellipticity. We prove the partition property for problems without ellipticity which are of practical importance. Example applications include implicit schemes applied to degenerate parabolic partial differential equations arising from superconductors, superfluids and liquid crystals. With this partition property, Schwarz algorithms can be applied to general non-elliptic problems with an h-independent optimal convergence rate. Application to the time-dependent Ginzburg-Landau model of superconductivity is illustrated and numerical results are presented.

  10. Sedimentation of a suspension in a centrifugal field.

    Science.gov (United States)

    Lueptow, R M; Hübler, W

    1991-11-01

    To model centrifugal sedimentation of biological suspensions, the time history of sedimentation of particles in a centrifugal field was considered for two geometries: a tube and a cylindrical container. The Kynch theory for batch gravitational settling in Cartesian coordinates based on mass conservation was extended to include a centrifugal sedimentation force, cylindrical coordinates, and the Hawksley-Vand hindered settling model. The resulting quasi-linear partial differential equation was solved by the method of characteristics. The combination of radial dependence of the sedimentation force and cylindrical geometry in the centrifugal case results in several differences in the time-position history diagram of the sedimentation process compared to the gravitational case. First, instead of a region of uniform concentration equal to the initial concentration, a region of concentration that is continuously decreasing with time results. Second, in the region of particle accumulation, curved constant concentration contours result instead of straight lines. Finally, a secondary shock that is dependent upon the initial concentration and the radius ratio of the rotating vessel appears in the centrifugal case. The time history of the concentration for a particle suspension with an initial concentration typical of blood is presented.

  11. Exosome enrichment of human serum using multiple cycles of centrifugation.

    Science.gov (United States)

    Kim, Jeongkwon; Tan, Zhijing; Lubman, David M

    2015-09-01

    In this work, we compared the use of repeated cycles of centrifugation at conventional speeds for enrichment of exosomes from human serum compared to the use of ultracentrifugation (UC). After removal of cells and cell debris, a speed of 110 000 × g or 40 000 × g was used for the UC or centrifugation enrichment process, respectively. The enriched exosomes were analyzed using the bicinchoninic acid assay, 1D gel separation, transmission electron microscopy, Western blotting, and high-resolution LC-MS/MS analysis. It was found that a five-cycle repetition of UC or centrifugation is necessary for successful removal of nonexosomal proteins in the enrichment of exosomes from human serum. More significantly, 5× centrifugation enrichment was found to provide similar or better performance than 5× UC enrichment in terms of enriched exosome protein amount, Western blot band intensity for detection of CD-63, and numbers of identified exosome-related proteins and cluster of differentiation (CD) proteins. A total of 478 proteins were identified in the LC-MS/MS analyses of exosome proteins obtained from 5× UCs and 5× centrifugations including many important CD membrane proteins. The presence of previously reported exosome-related proteins including key exosome protein markers demonstrates the utility of this method for analysis of proteins in human serum.

  12. Experience with the Sarns centrifugal pump in postcardiotomy ventricular failure.

    Science.gov (United States)

    Curtis, J J; Walls, J T; Schmaltz, R; Boley, T M; Nawarawong, W; Landreneau, R J

    1992-09-01

    The reported clinical use of the Sarns centrifugal pump (Sarns, Inc./3M, Ann Arbor, Mich.) as a cardiac assist device for postcardiotomy ventricular failure is limited. During a 25-month period ending November 1988, we used 40 Sarns centrifugal pumps as univentricular or biventricular cardiac assist devices in 27 patients who could not be weaned from cardiopulmonary bypass despite maximal pharmacologic and intraaortic balloon support. Eighteen men and nine women with a mean age of 60.4 years (28 to 83) required assistance. Left ventricular assist alone was used in 12 patients, right ventricular assist in 2, and biventricular assist in 13. The duration of assist ranged from 2 to 434 hours (median 45). Centrifugal assist was successful in weaning 100% of the patients. Ten of 27 patients (37%) improved hemodynamically, allowing removal of the device(s), and 5 of 27 (18.5%) survived hospitalization. Survival of patients requiring left ventricular assist only was 33.3% (4/12). Complications were common and included renal failure, hemorrhage, coagulopathy, ventricular arrhythmias, sepsis, cerebrovascular accident, and wound infection. During 3560 centrifugal pump hours, no pump thrombosis was observed. The Sarns centrifugal pump is an effective assist device when used to salvage patients who otherwise cannot be weaned from cardiopulmonary bypass. Statistical analysis of preoperative patient characteristics, operative risk factors, and postoperative complications failed to predict which patients would be weaned from cardiac assist or which would survive.

  13. Centrifuge modelling of drained lateral pile - soil response

    DEFF Research Database (Denmark)

    Klinkvort, Rasmus Tofte

    of rigid piles. The tests have been performed in homogeneously dense dry or saturated Fontainebleau sand in order to mimic simplified drained offshore soil conditions. Approximately half of the tests have been carried out to investigate the centrifuge procedure in order to create a methodology of testing...... for monopiles today. Therefore it appears that the methodology for monopiles lacks scientific justification and a better understanding of rigid piles is needed. More than 70 centrifuge tests on laterally loaded rigid model piles have been carried out in connection with this thesis to get a better understanding...... that enables the transformation of result from tests in model scale to prototype scale. The grain size to pile diameter ratio, the non-linear stress distribution and the pile installation was identified from this investigation as important parameters in reliable scaling of centrifuge results. The remaining...

  14. Investigation of Surge Behavior in a Micro Centrifugal Compressor

    Institute of Scientific and Technical Information of China (English)

    Shimpei MIZUKI; Yuichiro ASAGA; Yushi ONO; Hoshio TSUJITA

    2006-01-01

    This paper reports the experimental and theoretical study of the surge occurred in prototyping an ultra micro centrifugal compressor. As the first step, the 10 times size model of an ultra micro centrifugal compressor having the 40 mm outer diameter was designed and manufactured. The detailed experimental investigations for the transient behavior of surge with several different values of B parameter were carried out. The experimental results during the surge were compared with those obtained by the non-linear lumped parameter theory in order to validate the effectiveness of the theoretical surge model for the micro centrifugal compressor. As a result, the quite different behavior of the surge appeared for the different values of B both in the experiment and in the analysis.

  15. Passively Shunted Piezoelectric Damping of Centrifugally-Loaded Plates

    Science.gov (United States)

    Duffy, Kirsten P.; Provenza, Andrew J.; Trudell, Jeffrey J.; Min, James B.

    2009-01-01

    Researchers at NASA Glenn Research Center have been investigating shunted piezoelectric circuits as potential damping treatments for turbomachinery rotor blades. This effort seeks to determine the effects of centrifugal loading on passively-shunted piezoelectric - damped plates. Passive shunt circuit parameters are optimized for the plate's third bending mode. Tests are performed both non-spinning and in the Dynamic Spin Facility to verify the analysis, and to determine the effectiveness of the damping under centrifugal loading. Results show that a resistive shunt circuit will reduce resonant vibration for this configuration. However, a tuned shunt circuit will be required to achieve the desired damping level. The analysis and testing address several issues with passive shunt circuit implementation in a rotating system, including piezoelectric material integrity under centrifugal loading, shunt circuit implementation, and tip mode damping.

  16. Centrifuge modeling of shallow foundation on soft soil

    Energy Technology Data Exchange (ETDEWEB)

    Leung, P.K.; Ku, H.Y.; Pane, V.; Schiffman, R.L.

    1984-05-01

    A series of centrifuge model tests was performed to study the behavior of shallow foundations on soft normally consolidated clay. The model tests included testing of foundation models with one-dimensional, plane strain, and axially symmetric geometries. The nonlinear consolidation properties of the soil were determined using specially developed laboratory testing techniques. The centrifuge test data were then compared with conventional and finite strain theories for consolidation assessment, as well as a limit analysis solution for foundation stability considerations. It is found that centrifuge testing coupled with careful laboratory testing provides a useful tool to validate analytical procedures. It has demonstrated that the finite strain theory and the limit analysis solution are valid procedures for the determination of consolidation settlement and foundation penetration of shallow foundations on soft soil, respectively.

  17. Studies on preparation of aceclofenac pellets by centrifugal granulator

    Directory of Open Access Journals (Sweden)

    Zibin GAO

    Full Text Available To prepare aceclofenac pellets by centrifugal granulation. Using 90~100 g of starch pellets as the core pellets,100 g of aceclofenac mixed with 50 g of microcrystalline cellulose(MCC and 4 g talc, methyl cellulose (HPMC as binder,the aceclofenac pellets were prepared by centrifugal granulation .And evaluate the quality of the pellets. The aceclofenac pellets had high yield and less losses,the pellets had a partical size of 0.70~0.88 mm(18~24 mesh)and had uniform particle size .the moisture ,drug content and dissolution meet the requirement . Aceclofenac pellets were prepared by the process of centrifugal granulation .The preparation prescription and process parameters were optimized by single factor method .and the pellets meet the standard requirements.

  18. Centrifugally activated bearing for high-speed rotating machinery

    Science.gov (United States)

    Post, Richard F.

    1994-01-01

    A centrifugally activated bearing is disclosed. The bearing includes an annular member that extends laterally and radially from a central axis. A rotating member that rotates about the central axis relative to the annular member is also included. The rotating member has an interior chamber that surrounds the central axis and in which the annular member is suspended. Furthermore, the interior chamber has a concave shape for retaining a lubricant therein while the rotating member is at rest and for retaining a lubricant therein while the rotating member is rotating. The concave shape is such that while the rotating member is rotating a centrifugal force causes a lubricant to be forced away from the central axis to form a cylindrical surface having an axis collinear with the central axis. This centrifugally displaced lubricant provides restoring forces to counteract lateral displacement during operation.

  19. Reducing variance in batch partitioning measurements

    Energy Technology Data Exchange (ETDEWEB)

    Mariner, Paul E.

    2010-08-11

    The partitioning experiment is commonly performed with little or no attention to reducing measurement variance. Batch test procedures such as those used to measure K{sub d} values (e.g., ASTM D 4646 and EPA402 -R-99-004A) do not explain how to evaluate measurement uncertainty nor how to minimize measurement variance. In fact, ASTM D 4646 prescribes a sorbent:water ratio that prevents variance minimization. Consequently, the variance of a set of partitioning measurements can be extreme and even absurd. Such data sets, which are commonplace, hamper probabilistic modeling efforts. An error-savvy design requires adjustment of the solution:sorbent ratio so that approximately half of the sorbate partitions to the sorbent. Results of Monte Carlo simulations indicate that this simple step can markedly improve the precision and statistical characterization of partitioning uncertainty.

  20. Spatially Partitioned Embedded Runge--Kutta Methods

    KAUST Repository

    Ketcheson, David I.

    2013-10-30

    We study spatially partitioned embedded Runge--Kutta (SPERK) schemes for partial differential equations (PDEs), in which each of the component schemes is applied over a different part of the spatial domain. Such methods may be convenient for problems in which the smoothness of the solution or the magnitudes of the PDE coefficients vary strongly in space. We focus on embedded partitioned methods as they offer greater efficiency and avoid the order reduction that may occur in nonembedded schemes. We demonstrate that the lack of conservation in partitioned schemes can lead to nonphysical effects and propose conservative additive schemes based on partitioning the fluxes rather than the ordinary differential equations. A variety of SPERK schemes are presented, including an embedded pair suitable for the time evolution of fifth-order weighted nonoscillatory spatial discretizations. Numerical experiments are provided to support the theory.

  1. OPTIMAL PARTITIONS OF DATA IN HIGHER DIMENSIONS

    Data.gov (United States)

    National Aeronautics and Space Administration — OPTIMAL PARTITIONS OF DATA IN HIGHER DIMENSIONS BRADLEY W. JACKSON*, JEFFREY D. SCARGLE, AND CHRIS CUSANZA, DAVID BARNES, DENNIS KANYGIN, RUSSELL SARMIENTO, SOWMYA...

  2. Connections between groundwater flow and transpiration partitioning

    Science.gov (United States)

    Maxwell, Reed M.; Condon, Laura E.

    2016-07-01

    Understanding freshwater fluxes at continental scales will help us better predict hydrologic response and manage our terrestrial water resources. The partitioning of evapotranspiration into bare soil evaporation and plant transpiration remains a key uncertainty in the terrestrial water balance. We used integrated hydrologic simulations that couple vegetation and land-energy processes with surface and subsurface hydrology to study transpiration partitioning at the continental scale. Both latent heat flux and partitioning are connected to water table depth, and including lateral groundwater flow in the model increases transpiration partitioning from 47 ± 13 to 62 ± 12%. This suggests that lateral groundwater flow, which is generally simplified or excluded in Earth system models, may provide a missing link for reconciling observations and global models of terrestrial water fluxes.

  3. Perturbative partition function for squashed S^5

    CERN Document Server

    Imamura, Yosuke

    2012-01-01

    We compute the index of 6d N=(1,0) theories on S^5xR containing vector and hypermultiplets. We only consider the perturbative sector without instantons. By compactifying R to S^1 with a twisted boundary condition and taking the small radius limit, we derive the perturbative partition function on a squashed S^5. The 1-loop partition function is represented in a simple form with the triple sine function.

  4. Congruences involving F-partition functions

    Directory of Open Access Journals (Sweden)

    James Sellers

    1994-01-01

    Full Text Available The primary goal of this note is to prove the congruence ϕ3(3n+2≡0(mod3, where ϕ3(n denotes the number of F-partitions of n with at most 3 repetitions. Secondarily, we conjecture a new family of congruences involving cϕ2(n, the number of F-partitions of n with 2 colors.

  5. Actinide and fission product partitioning and transmutation

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-07-01

    The fourth international information exchange meeting on actinide and fission product partitioning and transmutation, took place in Mito City in Japan, on 111-13 September 1996. The proceedings are presented in six sessions: the major programmes and international cooperation, the partitioning and transmutation programs, feasibility studies, particular separation processes, the accelerator driven transmutation, and the chemistry of the fuel cycle. (A.L.B.)

  6. Centrifuge modelling of a laterally cyclic loaded pile

    DEFF Research Database (Denmark)

    Klinkvort, Rasmus Tofte; Leth, Caspar Thrane; Hededal, Ole

    2010-01-01

    A total number of 9 static and 6 cyclic centrifuge tests on laterally loaded piles in very dense, dry sand was erformed. The prototype dimensions of the piles were 1 meter in diameter and penetration depths varying from 6 to 10 meters. The static tests were used to investigate the initial subgrade...... reaction modulus and as a reference for cyclic tests. For the cyclic tests the accumulation of deflections and the change in secant stiffness of the soil from repetitive loading were investigated. From all the tests carried out accumulations of deflections were seen. rom the centrifuge tests it was seen...

  7. Secondary Containment Design for a High Speed Centrifuge

    Energy Technology Data Exchange (ETDEWEB)

    Snyder, K.W.

    1999-03-01

    Secondary containment for high speed rotating machinery, such as a centrifuge, is extremely important for operating personnel safety. Containment techniques can be very costly, ungainly and time consuming to construct. A novel containment concept is introduced which is fabricated out of modular sections of polycarbonate glazed into a Unistrut metal frame. A containment study for a high speed centrifuge is performed which includes the development of parameters for secondary containment design. The Unistrut/polycarbonate shield framing concept is presented including design details and proof testing procedures. The economical fabrication and modularity of the design indicates a usefulness for this shielding system in a wide variety of containment scenarios.

  8. Aspiration spiral-flow type centrifugal flotation machine

    Institute of Scientific and Technical Information of China (English)

    陈文义

    2002-01-01

    Aspiration spiral flow type centrifugal flotation machine takes full advantage of centrifugal force field and gravitational field, and strengthens flotation of coal slurry. As a new-type flotation machine of high efficiency, its key component is bubble generator. Which completes the process of ore pulp inflation and liberalization. The design, parameters and working principle of bubble generator provide the design of the same device in similar equipment with reference. The result of industrial operation shows that this machine is of such features as small occupational area, greater concentration ratio, high processing capacity, high efficiency and lower investment etc.

  9. Centripetal Acceleration and Centrifugal Force in General Relativity

    Science.gov (United States)

    Bini, D.; de Felice, F.; Jantzen, R. T.

    2003-05-01

    In nonrelativistic mechanics noninertial observers studying accelerated test particle motion experience a centripetal acceleration which, once interpreted as a centrifugal force acting on the particle, allows writing the particle's equation of motion in a Newtonian form, simply by adding the inertial force contribution to that of the external forces in the acceleration-equals-force equation. In general relativity centripetal and centrifugal acceleration generalizing the classical concepts must be properly (geometrically) defined. This requires a relative Frenet-Serret frame approach based on a family of test observers.

  10. Model Based Fault Detection in a Centrifugal Pump Application

    DEFF Research Database (Denmark)

    Kallesøe, Carsten; Cocquempot, Vincent; Izadi-Zamanabadi, Roozbeh

    2006-01-01

    A model based approach for fault detection in a centrifugal pump, driven by an induction motor, is proposed in this paper. The fault detection algorithm is derived using a combination of structural analysis, observer design and Analytical Redundancy Relation (ARR) design. Structural consideration...... is capable of detecting four different faults in the mechanical and hydraulic parts of the pump.......A model based approach for fault detection in a centrifugal pump, driven by an induction motor, is proposed in this paper. The fault detection algorithm is derived using a combination of structural analysis, observer design and Analytical Redundancy Relation (ARR) design. Structural considerations...

  11. A Gray path on binary partitions

    CERN Document Server

    Colthurst, Thomas

    2009-01-01

    A binary partition of a positive integer $n$ is a partition of $n$ in which each part has size a power of two. In this note we first construct a Gray sequence on the set of binary partitions of $n$. This is an ordering of the set of binary partitions of each $n$ (or of all $n$) such that adjacent partitions differ by one of a small set of elementary transformations; here the allowed transformatios are replacing $2^k+2^k$ by $2^{k+1}$ or vice versa (or addition of a new +1). Next we give a purely local condition for finding the successor of any partition in this sequence; the rule is so simple that successive transitions can be performed in constant time. Finally we show how to compute directly the bijection between $k$ and the $k$th term in the sequence. This answers a question posed by Donald Knuth in section 7.2.1 of The Art of Computer Programming.

  12. RSC Chromatography Monographs Quantitative In Silico Chromatography Computational Modelling of Molecular Interactions.

    Science.gov (United States)

    Hanai, Toshihiko

    2014-07-29

    All early chromatographic techniques, starting from the primitive "ancient" chromatography introduced by Tswett in the very early twentieth century, perfected in partition chromatography in the 1940s by Martin and Synge, and extended to a variety of additional separation mechanisms later, were first entirely experimental trial-and-error methods. The early years can also be characterized by searching for theoretical base of various separation techniques that would allow establishing relation between the structure of the analytes and their chromatographic behavior. The advent of computers followed by development of the new software then revolutionized the theoretical approaches and enabled detailed modeling instead of tedious experimentation. This book introduces the readers to the era of computational modeling in which molecular interactions are used to analyze the mechanisms of general molecular interactions with a special focus on biological applications. This article is protected by copyright. All rights reserved.

  13. Mechanism of Gas Intrusion into Molten Metal during Horizontal Centrifugal Casting

    Institute of Scientific and Technical Information of China (English)

    NI Feng; ZHANG Xhan-ling; YANG Di-xin; BI Xiao-qin; ZHANG Yong-zhen

    2004-01-01

    A mechanism of gas intrusion into molten metal during horizontal centrifugal casting was introduced .Based upon this concept, a special pouring method was suggested ,which can effectively prevent the pinhole defects in horizontal centrifugal castings.

  14. Centrifugal Model Tests on Railway Embankments of Expansive Soils

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    Based on the centrifugal model tests on railway embankments of expansive soil in Nanning-Kunming railway,the author studied several embankments under different physical conditions. The stress and strain states and settlement of the embankments were analyzed, and the obtained results can be used as a reference to field construction.

  15. Liquid egg white pasteurization using a centrifugal UV irradiator

    Science.gov (United States)

    Studies are lacking on UV nonthermal pasteurization of liquid egg white (LEW). The objective of this study was to inactivate Escherichia coli using a UV irradiator that centrifugally formed a thin film of LEW on the inside of a rotating cylinder. The LEW was inoculated with E. coli K12 to approximat...

  16. DEMONSTRATION BULLETIN: THE PLASMA CENTRIFUGAL FURNACE RETECH, INC.

    Science.gov (United States)

    The plasma centrifugal furnace is a thermal technology which uses the heat generated from a plasma torch to decontaminate metal and organic contaminated waste. This is accomplished by melting metal-bearing solids and, in the process, thermally destroying organic contaminants. The...

  17. Pasteurization of grapefruit juice using a centrifugal ultraviolet light irradiator

    Science.gov (United States)

    The pharmaceutical industry uses UV irradiators to inactivate viruses in liquids without heat. The penetration depth of UV in some liquids, such as serum plasma, can be short. To overcome this, very thin films may be produced by centrifugal force, small diameter tubing, or other means. Many liquid f...

  18. Latex micro-balloon pumping in centrifugal microfluidic platforms.

    Science.gov (United States)

    Aeinehvand, Mohammad Mahdi; Ibrahim, Fatimah; Harun, Sulaiman Wadi; Al-Faqheri, Wisam; Thio, Tzer Hwai Gilbert; Kazemzadeh, Amin; Madou, Marc

    2014-03-01

    Centrifugal microfluidic platforms have emerged as point-of-care diagnostic tools. However, the unidirectional nature of the centrifugal force limits the available space for multi-step processes on a single microfluidic disc. To overcome this limitation, a passive pneumatic pumping method actuated at high rotational speeds has been previously proposed to pump liquid against the centrifugal force. In this paper, a novel micro-balloon pumping method that relies on elastic energy stored in a latex membrane is introduced. It operates at low rotational speeds and pumps a larger volume of liquid towards the centre of the disc. Two different micro-balloon pumping mechanisms have been designed to study the pump performance at a range of rotational frequencies from 0 to 1500 rpm. The behaviour of the micro-balloon pump on the centrifugal microfluidic platforms has been theoretically analysed and compared with the experimental data. The experimental data show that the developed pumping method dramatically decreases the required rotational speed to pump liquid compared to the previously developed pneumatic pumping methods. It also shows that within a range of rotational speed, a desirable volume of liquid can be stored and pumped by adjusting the size of the micro-balloon.

  19. Pasteurization of Grapefruit Juice using a Centrifugal Ultraviolet Light Device

    Science.gov (United States)

    The pharmaceutical industry uses UV devices to nonthermally inactivate viruses in liquids. To overcome the low penetration depth of UV in some liquids, such as serum plasma, thin films are formed by centrifugal force. Liquid foods also have low UV penetration depths. Studies are lacking on nontherma...

  20. 14 CFR 35.35 - Centrifugal load tests.

    Science.gov (United States)

    2010-01-01

    ... Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: PROPELLERS Tests and Inspections § 35.35 Centrifugal load tests. The applicant must demonstrate that a propeller complies with paragraphs (a), (b) and (c) of this section without evidence of...

  1. Application of antioxidants and centrifugation for cryopreservation of boar spermatozoa.

    Science.gov (United States)

    Zhang, Wei; Yi, Kangle; Chen, Chao; Hou, Xiaofeng; Zhou, Xu

    2012-06-01

    Although cryopreserved boar semen has been available since 1975, a major breakthrough in commercial application has not yet occurred due to the high susceptibility of boar spermatozoa to damage during cryopreservation and the complicated process required for deep freezing. In recent years, the application of antioxidants during the cryopreservation of boar semen has been the subject of considerable research aimed at improving the quality of post-thaw semen. Centrifugation is necessary before using cryopreservation protocols for freezing boar spermatozoa. Studies of the effect of different centrifugation regimens on boar sperm recovery, yield and cryosurvival have made significant contributions. Therefore this review elucidates results of recent applications of various antioxidants and centrifugation regimens used in efforts to improve cryopreservation of boar spermatozoa. This review is intended to enhance understanding of the roles of these antioxidants and centrifugation regimens with respect to mechanisms that increase resistance to cryodamage of boar spermatozoa. In addition, the discussion addresses the need for developing an objective evaluation of effectiveness and estimating the prospect of application of new techniques for the cryopreservation of boar semen and its use in artificial insemination.

  2. Flow pattern in reverse-flow centrifugal separators

    NARCIS (Netherlands)

    Peng, W; Hoffmann, AC; Boot, PJAJ; Udding, A; Dries, HWA; Ekker, A; Kater, J

    2002-01-01

    Experimental flow patterns, determined by Laser Doppler Anemometry (LDA) for two types of reverse-flow centrifugal separators, are presented. The flow patterns in (a) a conventional cylinder-on-cone cyclone with tangential inlet and (b) a swirl tube with vane-generated swirl and a cylindrical body a

  3. Vibratory centrifuge for the dewatering of coal sludge

    Energy Technology Data Exchange (ETDEWEB)

    Schiele, H.; Schlebusch, L.

    1981-03-03

    A vibratory centrifuge for the dewatering of coal sludge, washed small coal or slack which comprises a revolvable conical screen which has a diameter that increases towards its discharge end. The conical screen is vibratable in an axial direction and includes radial steps each having a height of at least 20 mm to rearrangement or loosen the material in the zone of each step.

  4. Synthesis and Analytical Centrifugation of Magnetic Model Colloids

    NARCIS (Netherlands)

    Luigjes, B.

    2012-01-01

    This thesis is a study of the preparation and thermodynamic properties of magnetic colloids. First, two types of magnetic model colloids are investigated: composite colloids and single-domain nanoparticles. Thermodynamics of magnetic colloids is studied using analytical centrifugation, including a s

  5. Numerical Simulation and Cold Modeling experiments on Centrifugal Casting

    Science.gov (United States)

    Keerthiprasad, Kestur Sadashivaiah; Murali, Mysore Seetharam; Mukunda, Pudukottah Gopaliengar; Majumdar, Sekhar

    2011-02-01

    In a centrifugal casting process, the fluid flow eventually determines the quality and characteristics of the final product. It is difficult to study the fluid behavior here because of the opaque nature of melt and mold. In the current investigation, numerical simulations of the flow field and visualization experiments on cold models have been carried out for a centrifugal casting system using horizontal molds and fluids of different viscosities to study the effect of different process variables on the flow pattern. The effects of the thickness of the cylindrical fluid annulus formed inside the mold and the effects of fluid viscosity, diameter, and rotational speed of the mold on the hollow fluid cylinder formation process have been investigated. The numerical simulation results are compared with corresponding data obtained from the cold modeling experiments. The influence of rotational speed in a real-life centrifugal casting system has also been studied using an aluminum-silicon alloy. Cylinders of different thicknesses are cast at different rotational speeds, and the flow patterns observed visually in the actual castings are found to be similar to those recorded in the corresponding cold modeling experiments. Reasonable agreement is observed between the results of numerical simulation and the results of cold modeling experiments with different fluids. The visualization study on the hollow cylinders produced in an actual centrifugal casting process also confirm the conclusions arrived at from the cold modeling experiments and numerical simulation in a qualitative sense.

  6. Centrifugally driven microfluidic disc for detection of chromosomal translocations

    DEFF Research Database (Denmark)

    Brøgger, Anna Line; Kwasny, Dorota; Bosco, Filippo G.

    2012-01-01

    and prognosis of patients. In this work we demonstrate a novel, centrifugally-driven microfluidic system for controlled manipulation of oligonucleotides and subsequent detection of chromosomal translocations. The device is fabricated in the form of a disc with capillary burst microvalves employed to control...

  7. Centrifuge modelling of rigid piles in soft clay

    DEFF Research Database (Denmark)

    Klinkvort, R.T.; Poder, M.; Truong, P.;

    2016-01-01

    of this study is to employ centrifuge modelling in order to derive experimental p-y curves for rigid piles embedded in over-consolidated soft clay. A kaolin clay sample was prepared and pre-consolidated by applying a constant pressure at the soil surface, while different over-consolidation ratios were achieved...

  8. Ocular torsion before and after 1 hour centrifugation

    NARCIS (Netherlands)

    Groen, E.; Graaf, B. de; Bles, W.; Bos, J.E.

    1996-01-01

    To assess a possible otolith contribution to effects observed following prolonged expo-sure to hyper gravity, we used video-oculography to measure ocular torsion during static and dynamic conditions of lateral body tilt (roll) before and after one hour of centrifugation with a Gx-load of 3G. Static

  9. Polymers as reference partitioning phase: polymer calibration for an analytically operational approach to quantify multimedia phase partitioning

    DEFF Research Database (Denmark)

    Gilbert, Dorothea; Witt, Gesine; Smedes, Foppe;

    2016-01-01

    Polymers are increasingly applied for the enrichment of hydrophobic organic chemicals (HOCs) from various types of samples and media in many analytical partitioning-based measuring techniques. We propose using polymers as a reference partitioning phase and introduce polymer-polymer partitioning......-air) and multimedia partition coefficients (lipid-water, air-water) were calculated by applying the new concept of a polymer as reference partitioning phase and by using polymer-polymer partition coefficients as conversion factors. The present study encourages the use of polymer-polymer partition coefficients...... as the basis for a deeper insight into partitioning differences of HOCs between polymers, calibrating analytical methods, and consistency checking of existing and calculation of new partition coefficients. Polymer-polymer partition coefficients were determined for polychlorinated biphenyls (PCBs), polycyclic...

  10. German chemical plants with particular reference to centrifuges

    Energy Technology Data Exchange (ETDEWEB)

    Broadbent, F.

    1946-01-01

    This report consisted of 9 reports. Report No. 1 was about Elmore Metall A. G., Schlandern on Siegburg. Two divisions of works in this factory were: (1) tube-drawing section for copper, steel, and zinc, with old machinery; (2) a section making electrolytically-deposited copper cylinders up to 100'' diameter, of high purity and excellent mechanical properties. The electrolytically-deposited copper cylinders were produced in lead-lined wooden tanks. Report No. 2 was about H. Krantz Maschinenfabrik, Aachen. This firm specialized in hydro-extractors, confined to types suitable for laundries and textile work. The machines built were of sizes from 800 mm to 1,8000 mm basket diameter. Report No. 3 was about O. Doerries A. G., Vorm Banning, and Seyfold Duren. This firm specialized in paper-making machinery, including centrifugal grit extractors for the treatment of paper stock. Erkensators number 4 and number 4L were compared in this report. Reports No. 4 and No. 5 were about I. G. Farbenindustrie, Dormagen, and Elberfeld. General information about the continuously-operating centrifuges was given. Report No. 6 was about Glanstoff Courtald between Cologne and Dormagen, where they used two methods of extracting water from viscose cakes, (1) by multiple-hinged candle hydro-extractors, and (2) by converted spinning pots. Report No. 7 was about Matthers and Weber, Duisberg, and gave general information about two kinds of centrifuges, (1) for crude bi-carbonate, and (2) for refined bi-carbonate. Report No. 8 was about Westfalia Separator A. G., Oelde; where the high-speed centrifuges of the ''cream separator'' or Laval type were made. Report No. 9 was about Escher Wyss, Ravensburg, where centrifuges, water turbines, spray dryers, and paper-making machinery were manufactured.

  11. Comparative analysis of discrete exosome fractions obtained by differential centrifugation

    Directory of Open Access Journals (Sweden)

    Dennis K. Jeppesen

    2014-11-01

    Full Text Available Background: Cells release a mixture of extracellular vesicles, amongst these exosomes, that differ in size, density and composition. The standard isolation method for exosomes is centrifugation of fluid samples, typically at 100,000×g or above. Knowledge of the effect of discrete ultracentrifugation speeds on the purification from different cell types, however, is limited. Methods: We examined the effect of applying differential centrifugation g-forces ranging from 33,000×g to 200,000×g on exosome yield and purity, using 2 unrelated human cell lines, embryonic kidney HEK293 cells and bladder carcinoma FL3 cells. The fractions were evaluated by nanoparticle tracking analysis (NTA, total protein quantification and immunoblotting for CD81, TSG101, syntenin, VDAC1 and calreticulin. Results: NTA revealed the lowest background particle count in Dulbecco's Modified Eagle's Medium media devoid of phenol red and cleared by 200,000×g overnight centrifugation. The centrifugation tube fill level impacted the sedimentation efficacy. Comparative analysis by NTA, protein quantification, and detection of exosomal and contamination markers identified differences in vesicle size, concentration and composition of the obtained fractions. In addition, HEK293 and FL3 vesicles displayed marked differences in sedimentation characteristics. Exosomes were pelleted already at 33,000×g, a g-force which also removed most contaminating microsomes. Optimal vesicle-to-protein yield was obtained at 67,000×g for HEK293 cells but 100,000×g for FL3 cells. Relative expression of exosomal markers (TSG101, CD81, syntenin suggested presence of exosome subpopulations with variable sedimentation characteristics. Conclusions: Specific g-force/k factor usage during differential centrifugation greatly influences the purity and yield of exosomes. The vesicle sedimentation profile differed between the 2 cell lines.

  12. Fun with Paper Chromatography.

    Science.gov (United States)

    Coleman, Dava; Hounshell, Paul B.

    1982-01-01

    Discusses paper chromatographic techniques and provides examples of typical classroom activities. Includes description of retardation values obtained during chromatography exercises and suggests using them for math lessons. (JN)

  13. A biologically motivated partitioning of mortality.

    Energy Technology Data Exchange (ETDEWEB)

    Carnes, B. A.; Olshansky, S. J.; Center for Mechanistic Biology and Biotechnology; Univ. of Chicago

    1997-01-01

    For over a century, actuaries and biologists working independently of each other have presented arguments for why total mortality needs to be partitioned into biologically meaningful subcomponents. These mortality partitions tended to overlook genetic diseases that are inherited because the partitions were motivated by a paradigm focused on aging. In this article, we combine and extend the concepts from these disciplines to develop a conceptual partitioning of total mortality into extrinsic and intrinsic causes of death. An extrinsic death is either caused or initiated by something that originates outside the body of an individual, while an intrinsic death is either caused or initiated by processes that originate within the body. It is argued that extrinsic mortality has been a driving force in determining why we die when we do from intrinsic causes of death. This biologically motivated partitioning of mortality provides a useful perspective for researchers interested in comparative mortality analyses, the consequences of population aging, limits to human life expectancy, the progress made by the biomedical sciences against lethal diseases, and demographic models that predict the life expectancy of future populations.

  14. Screening of pesticides for environmental partitioning tendency.

    Science.gov (United States)

    Gramatica, Paola; Di Guardo, Antonio

    2002-06-01

    The partitioning tendency of chemicals, in this study pesticides in particular, into different environmental compartments depends mainly on the concurrent relevance of the physico-chemical properties of the chemical itself. To rank the pesticides according to their distribution tendencies in the different environmental compartments we propose a multivariate approach: the combination, by principal component analysis, of those physico-chemical properties like organic carbon partition coefficient (Koc), n-octanol/water partition coefficient (Kow), water solubility (Sw), vapour pressure and Henry's law constant (H) that are more relevant to the determination of environmental partitioning. The resultant macrovariables, the PC1 and PC2 scores here named leaching index (LIN) and volatality index (VIN), are proposed as preliminary environmental partitioning indexes in different media. These two indexes are modeled by theoretical molecular descriptors with satisfactory predictive power. Such an approach allows a rapid pre-determination and screening of the environmental distribution of pesticides starting only from the molecular structure of the pesticide, without any a priori knowledge of the physico-chemical properties.

  15. 21 CFR 864.9275 - Blood bank centrifuge for in vitro diagnostic use.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Blood bank centrifuge for in vitro diagnostic use... Manufacture Blood and Blood Products § 864.9275 Blood bank centrifuge for in vitro diagnostic use. (a) Identification. A blood bank centrifuge for in vitro diagnostic use is a device used only to separate blood...

  16. 40 CFR Appendix - Alternative Organic HAP Emissions Limits for Open Molding, Centrifugal Casting, and SMC...

    Science.gov (United States)

    2010-07-01

    ... Limits for Open Molding, Centrifugal Casting, and SMC Manufacturing Operations Where the Standards Are..., Table 5 Alternative Organic HAP Emissions Limits for Open Molding, Centrifugal Casting, and SMC... casting—CR/HS 3,4 A vent system that moves heated air through the mold 27 lb/ton. 8. Centrifugal...

  17. A novel technique using the Hendrickx centrifuge for extracting winter sporangia of Synchytrium endobioticum from soil

    NARCIS (Netherlands)

    Wander, J.G.N.; Berg, van den W.; Boogert, van den P.H.J.F.; Lamers, J.G.; Leeuwen, van G.C.M.; Hendrickx, G.; Bonants, P.J.M.

    2007-01-01

    A zonal centrifugation method, known as the Hendrickx centrifuge technique, was tested for routine detection of winter sporangia of Synchytrium endobioticum in soil. In four experiments the ability of the Hendrickx centrifuge to extract the sporangia from soil was compared with a method used by the

  18. 77 FR 65360 - Grant of Authority for Subzone Status (Centrifugal and Submersible Pumps); Auburn, NY

    Science.gov (United States)

    2012-10-26

    ... Foreign-Trade Zones Board Grant of Authority for Subzone Status (Centrifugal and Submersible Pumps... subzone at the centrifugal and submersible pump manufacturing and warehousing facilities of Xylem Water... activity related to the manufacturing of centrifugal and submersible pumps and related controllers at...

  19. Combinatorics and complexity of partition functions

    CERN Document Server

    Barvinok, Alexander

    2016-01-01

    Partition functions arise in combinatorics and related problems of statistical physics as they encode in a succinct way the combinatorial structure of complicated systems. The main focus of the book is on efficient ways to compute (approximate) various partition functions, such as permanents, hafnians and their higher-dimensional versions, graph and hypergraph matching polynomials, the independence polynomial of a graph and partition functions enumerating 0-1 and integer points in polyhedra, which allows one to make algorithmic advances in otherwise intractable problems. The book unifies various, often quite recent, results scattered in the literature, concentrating on the three main approaches: scaling, interpolation and correlation decay. The prerequisites include moderate amounts of real and complex analysis and linear algebra, making the book accessible to advanced math and physics undergraduates. .

  20. Parallel Graph Partitioning for Complex Networks

    CERN Document Server

    Meyerhenke, Henning; Schulz, Christian

    2014-01-01

    Processing large complex networks like social networks or web graphs has recently attracted considerable interest. In order to do this in parallel, we need to partition them into pieces of about equal size. Unfortunately, previous parallel graph partitioners originally developed for more regular mesh-like networks do not work well for these networks. This paper addresses this problem by parallelizing and adapting the label propagation technique originally developed for graph clustering. By introducing size constraints, label propagation becomes applicable for both the coarsening and the refinement phase of multilevel graph partitioning. We obtain very high quality by applying a highly parallel evolutionary algorithm to the coarsened graph. The resulting system is both more scalable and achieves higher quality than state-of-the-art systems like ParMetis or PT-Scotch. For large complex networks the performance differences are very big. For example, our algorithm can partition a web graph with 3.3 billion edges ...

  1. Partition functions and graphs: A combinatorial approach

    CERN Document Server

    Solomon, A I; Duchamp, G; Horzela, A; Penson, K A; Solomon, Allan I.; Blasiak, Pawel; Duchamp, Gerard; Horzela, Andrzej; Penson, Karol A.

    2004-01-01

    Although symmetry methods and analysis are a necessary ingredient in every physicist's toolkit, rather less use has been made of combinatorial methods. One exception is in the realm of Statistical Physics, where the calculation of the partition function, for example, is essentially a combinatorial problem. In this talk we shall show that one approach is via the normal ordering of the second quantized operators appearing in the partition function. This in turn leads to a combinatorial graphical description, giving essentially Feynman-type graphs associated with the theory. We illustrate this methodology by the explicit calculation of two model examples, the free boson gas and a superfluid boson model. We show how the calculation of partition functions can be facilitated by knowledge of the combinatorics of the boson normal ordering problem; this naturally gives rise to the Bell numbers of combinatorics. The associated graphical representation of these numbers gives a perturbation expansion in terms of a sequen...

  2. Acyl-CoA metabolism and partitioning

    DEFF Research Database (Denmark)

    Grevengoed, Trisha J; Klett, Eric L; Coleman, Rosalind A

    2014-01-01

    expression patterns and subcellular locations. Their acyl-CoA products regulate metabolic enzymes and signaling pathways, become oxidized to provide cellular energy, and are incorporated into acylated proteins and complex lipids such as triacylglycerol, phospholipids, and cholesterol esters. Their differing...... metabolic fates are determined by a network of proteins that channel the acyl-CoAs toward or away from specific metabolic pathways and serve as the basis for partitioning. This review evaluates the evidence for acyl-CoA partitioning by reviewing experimental data on proteins that are believed to contribute...... to acyl-CoA channeling, the metabolic consequences of loss of these proteins, and the potential role of maladaptive acyl-CoA partitioning in the pathogenesis of metabolic disease and carcinogenesis....

  3. Cochlear implant in incomplete partition type I.

    Science.gov (United States)

    Berrettini, S; Forli, F; De Vito, A; Bruschini, L; Quaranta, N

    2013-02-01

    In this investigation, we report on 4 patients affected by incomplete partition type I submitted to cochlear implant at our institutions. Preoperative, surgical, mapping and follow-up issues as well as results in cases with this complex malformation are described. The cases reported in the present study confirm that cochlear implantation in patients with incomplete partition type I may be challenging for cochlear implant teams. The results are variable, but in many cases satisfactory, and are mainly related to the surgical placement of the electrode and residual neural nerve fibres. Moreover, in some cases the association of cochlear nerve abnormalities and other disabilities may significantly affect results.

  4. Advanced Coarsening Schemes for Graph Partitioning

    CERN Document Server

    Safro, Ilya; Schulz, Christian

    2012-01-01

    The graph partitioning problem is widely used and studied in many practical and theoretical applications. The multilevel strategies represent today one of the most effective and efficient generic frameworks for solving this problem on large-scale graphs. Most of the attention in designing the multilevel partitioning frameworks has been on the refinement phase. In this work we focus on the coarsening phase, which is responsible for creating structurally similar to the original but smaller graphs. We compare different matching- and AMG-based coarsening schemes, experiment with the algebraic distance between nodes, and demonstrate computational results on several classes of graphs that emphasize the running time and quality advantages of different coarsenings.

  5. Partitioning and transmutation. Annual Report 1997

    Energy Technology Data Exchange (ETDEWEB)

    Enarsson, Aa.; Landgren, A.; Liljenzin, J.O.; Skaalberg, M.; Spjuth, L. [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Nuclear Chemistry

    1997-12-01

    The current research project on partitioning and transmutation at the Dept. of Nuclear Chemistry, CTH, has the primary objective to investigate separation processes useful in connection with transmutation of long-lived radionuclides in high level nuclear waste. Partitioning is necessary in order to recover and purify the elements before and after each irradiation in a P and T treatment. In order to achieve a high transmutation efficiency the chemical separation process used must have small losses to various waste streams. At present, only aqueous based separation processes are known to be able to achieve the high recovery and separation efficiencies necessary for a useful P and T process. Refs, figs, tabs.

  6. Program Partitioning using Dynamic Trust Models

    DEFF Research Database (Denmark)

    Søndergaard, Dan; Probst, Christian W.; Jensen, Christian D.;

    2006-01-01

    -based scenarios. Language-based technologies have been suggested to support developers of those applications---the \\$\\backslash\\$emph{Decentralized Label Model} and \\$\\backslash\\$emph{Secure Program Partitioning} allow to annotate programs with security specifications, and to partition the annotated program...... across a set of hosts, obeying both the annotations and the trust relation between the principals. The resulting applications guarantee \\$\\backslash\\$emph{by construction} that safety and confidentiality of both data and computations are ensured. In this work, we develop a generalised version...

  7. Liquid Chromatography in 1982.

    Science.gov (United States)

    Freeman, David H.

    1982-01-01

    Reviews trends in liquid chromatography including apparatus, factors affecting efficient separation of a mixture (peak sharpness and speed), simplified problem-solving, adsorption, bonded phase chromatography, ion selectivity, and size exclusion. The current trend is to control chemical selectivity by the liquid phase. (Author/JN)

  8. Column Liquid Chromatography.

    Science.gov (United States)

    Majors, Ronald E.; And Others

    1984-01-01

    Reviews literature covering developments of column liquid chromatography during 1982-83. Areas considered include: books and reviews; general theory; columns; instrumentation; detectors; automation and data handling; multidimensional chromatographic and column switching techniques; liquid-solid chromatography; normal bonded-phase, reversed-phase,…

  9. Environmental and centrifugal factors influencing the visco-elastic properties of oral biofilms in vitro.

    Science.gov (United States)

    Peterson, Brandon W; Busscher, Henk J; Sharma, Prashant K; van der Mei, Henny C

    2012-01-01

    Centrifugal compaction causes changes in the surface properties of bacterial cells. It has been shown previously that the surface properties of planktonic cells change with increasing centrifugal compaction. This study aimed to analyze the influences of centrifugal compaction and environmental conditions on the visco-elastic properties of oral biofilms. Biofilms were grown out of a layer of initially adhering streptococci, actinomyces or a combination of these. Different uni-axial deformations were induced on the biofilms and the load relaxations were measured over time. Linear-Regression-Analysis demonstrated that both the centrifugation coefficient for streptococci and induced deformation influenced the percentage relaxation. Centrifugal compaction significantly influenced relaxation only upon compression of the outermost 20% of the biofilm (p centrifugal compaction of initially adhering, centrifuged bacteria extend to the visco-elastic properties of biofilms, indicating that the initial bacterial layer influences the structure of the entire biofilm.

  10. Centrifugal microfluidic platform for ultrasensitive detection of botulinum toxin.

    Science.gov (United States)

    Koh, Chung-Yan; Schaff, Ulrich Y; Piccini, Matthew E; Stanker, Larry H; Cheng, Luisa W; Ravichandran, Easwaran; Singh, Bal-Ram; Sommer, Greg J; Singh, Anup K

    2015-01-20

    We present an innovative centrifugal microfluidic immunoassay platform (SpinDx) to address the urgent biodefense and public health need for ultrasensitive point-of-care/incident detection of botulinum toxin. The simple, sample-to-answer centrifugal microfluidic immunoassay approach is based on binding of toxins to antibody-laden capture particles followed by sedimentation of the particles through a density-media in a microfluidic disk and quantification by laser-induced fluorescence. A blind, head-to-head comparison study of SpinDx versus the gold-standard mouse bioassay demonstrates 100-fold improvement in sensitivity (limit of detection = 0.09 pg/mL), while achieving total sample-to-answer time of capture beads and detection antibodies) are disconnected from the disk architecture and the reader, facilitating rapid development of new assays. SpinDx can also serve as a general-purpose immunoassay platform applicable to diagnosis of other conditions and diseases.

  11. Analysis of cantilever NEMS in centrifugal-fluidic systems

    Science.gov (United States)

    Mohsen-Nia, Mohsen; Abadian, Fateme; Abadian, Naeime; Dehkordi, Keivan Mosaiebi; Keivani, Maryam; Abadyan, Mohamadreza

    2016-07-01

    Electromechanical nanocantilevers are promising for using as sensors/detectors in centrifugal-fluidic systems. For this application, the presence of angular speed and electrolyte environment should be considered in the theoretical analysis. Herein, the pull-in instability of the nanocantilever incorporating the effects of angular velocity and liquid media is investigated using a size-dependent continuum theory. Using d’Alembert principle, the angular speed is transformed into an equivalent centrifugal force. The electrochemical and dispersion forces are incorporated considering the corrections due to the presence of electrolyte media. Two different approaches, i.e., the Rayleigh-Ritz method (RRM) and proposing a lumped parameter model (LPM), were applied to analyze the system. The models are validated with the results presented in literature. Impacts of the angular velocity, electrolyte media, dispersion forces, and size effect on the instability characteristics of the nanocantilever are discussed.

  12. Stage-efficiency of centrifugal extractor used in nuclear industry

    Institute of Scientific and Technical Information of China (English)

    吴秋林; 景山; 王兴海; 宋崇立

    2003-01-01

    The stage-efficiency of a single-stage prototype (d70) centrifugal extractor and the cascade is tested by HNO3-Nd3+ and 30%TRPO-kerosene system. The experimental results of the single-stage centrifugal extractor show that the carryover of the two phases decreases with increasing ratio of the two flow rate and rotation rate and the stage efficiency increases with not only decreasing total flow rate but also increasing rotor speed. However, the experimental results of the cascade show that the average stage efficiency of the cascade increases with not only decreasing total flow rate but also increasing rotor speed in both three-stage mode and two-stage mode.

  13. Dynamical System Analysis of Unsteady Phenomena in Centrifugal Compressor

    Institute of Scientific and Technical Information of China (English)

    YasuyukiKomatsubara; ShimpeiMizuki

    1997-01-01

    Surge and rotating stall occurring in a centrifugal compressor system are investigated by using a phase portrait reconstruction method.From experimentally measured time series of data,the method clarified the cyclic behavior of surge.For rotating stall,there still remain problems in the phase portrait due to the chaotic behavior.However,the results obtained by the present method are able to provide new insights to the modelings for surge and rotating stall.Surge and roatting stall occurring in a centrifugal compressor system are investigated by using a phase portrait reconstruction method.From experimentally measured time series of data,the method clarified the cylcic behavior of surge.For rotating stall,there still remain problems in the phase portrait due to the chaotic behavior.However,the results obtained by the present method are able to provide new insights to the modelings for surge and rotating stall.

  14. The simulation and performance of a centrifugal chiller

    Science.gov (United States)

    Jackson, W. L.; Chen, F. C.; Hwang, B. C.

    A computer simulation model was developed to analyze the performance of a water-cooled centrifugal chiller. The model is based on a heat pump thermodynamic cycle and empirical correlations for the performance of the system components. The system simulated is composed of a variable-speed centrifugal compressor with a hot-gas bypass option for capacity control, two shell-and-tube heat exchangers, and an expansion device. The model was validated and calibrated against the experimental test results of a 125-ton chiller. The performance of a similar chiller system at various operating conditions and design modifications was analyzed. System performance comparisons were made between a baseline case, cases with high-performance heat exchanger tubes and compressor motor, and various variable-speed compressor operating strategies. It was found that significant performance improvement can be realized by using variable-speed drive and on-demand control strategy.

  15. Centrifuge modeling of PGD response of buried pipe

    Institute of Scientific and Technical Information of China (English)

    Michael O'Rourke; Vikram Gadicherla; Tarek Abdoun

    2005-01-01

    A new centrifuge based method for determining the response of continuous buried pipe to PGD is presented.The physical characteristics of the RPI's 100 g-ton geotechnical centrifuge and the current lifeline experiment split-box are described: The split-box contains the model pipeline and surrounding soil and is manufactured such that half can be offset, in flight, simulating PGD. In addition, governing similitude relations which allow one to determine the physical characteristics,(diameter, wall thickness and material modulus of elasticity) of the model pipeline are presented. Finally, recorded strains induced in two buried pipes with prototype diameters of 0.63 m and 0.95 m (24 and 36 inch) subject to 0.6 and 2.0 meters (2and 6 feet) of full scale fault offsets and presented and compared to corresponding FE results.

  16. Hemocompatibility of a hydrodynamic levitation centrifugal blood pump.

    Science.gov (United States)

    Yamane, Takashi; Maruyama, Osamu; Nishida, Masahiro; Kosaka, Ryo; Sugiyama, Daisuke; Miyamoto, Yusuke; Kawamura, Hiroshi; Kato, Takahisa; Sano, Takeshi; Okubo, Takeshi; Sankai, Yoshiyuki; Shigeta, Osamu; Tsutsui, Tatsuo

    2007-01-01

    A noncontact type centrifugal pump without any complicated control or sensing modules has been developed as a long-term implantable artificial heart. Centrifugal pumps with impellers levitated by original hydrodynamic bearings were designed and have been modified through numerical analyses and in vitro tests. The hemolysis level was reduced by changing the pressure distribution around the impeller and subsequently expanding the bearing gap. Thrombus formation in the bearing was examined with in vitro thrombogenesis tests and was reduced by changing the groove shapes to increase the bearing-gap flow to 3% of the external flow. Unnecessary vortices around the vanes were also eliminated by changing the number of vanes from four to six.

  17. Considerations in designing a centrifugal atomiser for metal powder production

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Y.Y. [Department of Engineering, The University of Liverpool, Liverpool L69 3GH (United Kingdom)]. E-mail: y.y.zhao@livepool.ac.uk

    2006-07-01

    In centrifugal atomisation for metal powder production, the key to the control of the particle sizes is the design of the atomiser. This paper studies the main issues concerned in designing a centrifugal atomiser and provides guidance on the selection of an electric motor, radius of atomiser, slope angle of atomiser wall and flow rate of cooling water. In the selection of the atomiser radius, the power and material constraints as well as the hydraulic jump radius need to be considered. A cup atomiser with a slope angle of 60-70{sup o} would result in small spray droplets and thus a fine powder. The water cooling system needs to be assessed by examining the heat flow in the solid metal layer and in the atomiser.

  18. Production of centrifugal fields greater than 100 million times gravity.

    Science.gov (United States)

    Katano, R; Shimizu, S

    1979-07-01

    A high-speed rotation instrument to produce centrifugal fields greater than 100 million times gravity has been constructed. Small, solid, spherical high-carbon chromium steel rotors are suspended magnetically in high vacuum and spun by a rotating magnetic field. It is found that the spinning rotor explodes when the calculated average value of stress in the meridian plane reaches about 1.2 times the tensile strength of the material. The maximum speed of rotation so far achieved for more than a few days without bursting was obtained with a rotor of 1.50 mm diameter. The speed of 2.11 x 10(5) rev/s corresponded to a centrifugal field of 1.34 x 10(8) times gravity. Our instrument will find application in the study of nuclear atomic phenomena.

  19. Operation of Droplet-Microfluidic Devices with a Lab Centrifuge

    Directory of Open Access Journals (Sweden)

    Noorsher Ahmed

    2016-09-01

    Full Text Available Microfluidic devices are valuable for a variety of biotechnology applications, such as synthesizing biochemical libraries, screening enzymes, and analyzing single cells. However, normally, the devices are controlled using specialized pumps, which require expert knowledge to operate. Here, we demonstrate operation of poly(dimethylsiloxane devices without pumps. We build a scaffold that holds the device and reagents to be infused in a format that can be inserted into a 50 mL falcon tube and spun in a common lab centrifuge. By controlling the device design and centrifuge spin speed, we infuse the reagents at controlled flow rates. We demonstrate the encapsulation and culture of clonal colonies of red and green Escherichia coli in droplets seeded from single cells.

  20. Centrifuge Modeling of Piles Subjected to Lateral Loads

    Science.gov (United States)

    Brant, Logan; Ling, Hoe I.

    There are many applications where piles are employed to absorb and deflect lateral impact loads. Structural elements of this type are used to protect infrastructure and are commonly found at marine sites. A series of model tests have been conducted using Columbia University's centrifuge facility to better understand the performance of piles subjected to these loading conditions. A device was designed to install and laterally load single model piles during centrifuge flight. This device uniquely contains two lateral loading systems, one which allows static testing and another appropriate for dynamic tests. This research examines the behavior of tubular steel piles embedded within dry or saturated soil and subjected to varied rates of lateral loading. This investigation provides insight on the contribution of lateral loading rates to the behavior of piles.

  1. Massively parallel single-molecule manipulation using centrifugal force

    CERN Document Server

    Halvorsen, Ken

    2009-01-01

    Precise manipulation of single molecules has already led to remarkable insights in physics, chemistry, biology and medicine. However, widespread adoption of single-molecule techniques has been impeded by equipment cost and the laborious nature of making measurements one molecule at a time. We have solved these issues with a new approach: massively parallel single-molecule force measurements using centrifugal force. This approach is realized in a novel instrument that we call the Centrifuge Force Microscope (CFM), in which objects in an orbiting sample are subjected to a calibration-free, macroscopically uniform force-field while their micro-to-nanoscopic motions are observed. We demonstrate high-throughput single-molecule force spectroscopy with this technique by performing thousands of rupture experiments in parallel, characterizing force-dependent unbinding kinetics of an antibody-antigen pair in minutes rather than days. Additionally, we verify the force accuracy of the instrument by measuring the well-est...

  2. Determination of Free-Energy Relationships Using Gas Chromatography

    Science.gov (United States)

    Snow, Nicholas H.

    1996-06-01

    By performing a few straightforward analyses on a gas chromatograph, it is possible to calculate the free energy, enthalpy, and entropy changes that occur when a compound transfers between the mobile and stationary phases. The partition theory of chromatography allows this transfer to be expressed as a chemical equlibrium. By calculating the equilibrium constant for this reaction from chromatographic retention times, the standard free energy change may be determined, and from this, the standard enthalpy and entropy changes. Also, by calculating these values at several temperatures for structurally related compounds, it is possible to explore the relationship between chromatographic retention, standard free energy, and the structure of a compound. These calculations were performed for groups of homologous alcohols, acetates, and hydrocarbons on packed and capillary column gas chromatographs, using both polar and non-polar columns, and on computer simulation software. It is seen that for homologous compounds, the relationship between standard free energy change in partitioning and hydrocarbon chain length for this reaction is linear. It is also seen that gas chromatography represents a useful tool for the calculation and comparison of thermodynamic properties of compounds and that straightforward exercise of this type allows training of students in chromatographic analysis, basic partition theory, thermodynamic relationships, and linear free energy relationships.

  3. Scheduling Driven Partitioning of Heterogeneous Embedded Systems

    DEFF Research Database (Denmark)

    Pop, Paul; Eles, Petru; Peng, Zebo

    1998-01-01

    In this paper we present an algorithm for system level hardware/software partitioning of heterogeneous embedded systems. The system is represented as an abstract graph which captures both data-flow and the flow of control. Given an architecture consisting of several processors, ASICs and shared...

  4. Protium, an Infrastructure for Partitioned Applications

    NARCIS (Netherlands)

    Mullender, S.J.; Young, C.; Szymanski, T.; Reppy, J.; Presotto, D.; Pike, R.; Narlikar, G.

    2001-01-01

    Remote access feels different from local access. The major issues are consistency (machines vary in GUIs, applications, and devices) and responsiveness (the user must wait for network and server delays). Protium attacks these by partitioning programs into local viewers that connect to remote service

  5. Generating Milton Babbitt's all-partition arrays

    DEFF Research Database (Denmark)

    Bemman, Brian; Meredith, David

    2016-01-01

    backtracking algorithm for generating a particular type of all-partition array found in Babbitt’s works, known as a Smalley array. Constructing such an array is a difficult task, and we present two heuristics for helping to generate this type of structure. We provide the parameter values required...

  6. Domain wall partition functions and KP

    CERN Document Server

    Foda, O; Zuparic, M

    2009-01-01

    We observe that the partition function of the six vertex model on a finite square lattice with domain wall boundary conditions is (a restriction of) a KP tau function and express it as an expectation value of charged free fermions (up to an overall normalization).

  7. Actinide and fission product partitioning and transmutation

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-07-01

    The third international information exchange meeting on actinide and fission product partitioning and transmutation, took place in Cadarache France, on 12-14 December 1994. The proceedings are presented in six sessions : an introduction session, the major programmes and international cooperation, the systems studies, the reactors fuels and targets, the chemistry and a last discussions session. (A.L.B.)

  8. Countering oversegmentation in partitioning-based connectivities

    NARCIS (Netherlands)

    Ouzounis, Georgios K.; Wilkinson, Michael H.F.

    2005-01-01

    A new theoretical development is presented for handling the over-segmentation problem in partitioning-based connected openings. The definition we propose treats singletons generated with the earlier method, as elements of a larger connected component. Unlike the existing formalism, this new method a

  9. Plasmid and chromosome partitioning: surprises from phylogeny

    DEFF Research Database (Denmark)

    Gerdes, Kenn; Møller-Jensen, Jakob; Bugge Jensen, Rasmus

    2000-01-01

    Plasmids encode partitioning genes (par) that are required for faithful plasmid segregation at cell division. Initially, par loci were identified on plasmids, but more recently they were also found on bacterial chromosomes. We present here a phylogenetic analysis of par loci from plasmids and chr...

  10. Mapping Pesticide Partition Coefficients By Electromagnetic Induction

    Science.gov (United States)

    A potential method for reducing pesticide leaching is to base application rates on the leaching potential of a specific chemical and soil combination. However, leaching is determined in part by the partitioning of the chemical between the soil and soil solution, which varies across a field. Standard...

  11. Subsets of configurations and canonical partition functions

    DEFF Research Database (Denmark)

    Bloch, J.; Bruckmann, F.; Kieburg, M.;

    2013-01-01

    We explain the physical nature of the subset solution to the sign problem in chiral random matrix theory: the subset sum over configurations is shown to project out the canonical determinant with zero quark charge from a given configuration. As the grand canonical chiral random matrix partition...

  12. Topological String Partition Function on Generalised Conifolds

    CERN Document Server

    Gasparim, Elizabeth; Suzuki, Bruno; Torres-Gomez, Alexander

    2016-01-01

    We show that the partition function on a generalised conifold $C_{m,n}$ with ${m+n \\choose m}$ crepant resolutions can be equivalently computed on the compound du Val singularity $A_{m+n-1}\\times \\mathbb C$ with a unique crepant resolution.

  13. Fair Partitions of Polygons: An Elementary Introduction

    Indian Academy of Sciences (India)

    R Nandakumar; N Ramana Rao

    2012-08-01

    We introduce the question: Given a positive integer , can any 2D convex polygonal region be partitioned into convex pieces such that all pieces have the same area and the same perimeter? The answer to this question is easily `yes’ for =2. We give an elementary proof that the answer is `yes’ for =4 and generalize it to higher powers of 2.

  14. Discrepancy of LS-sequences of partitions

    CERN Document Server

    Carbone, Ingrid

    2010-01-01

    In this paper we give a precise estimate of the discrepancy of a class of uniformly distributed sequences of partitions. Among them we found a large class having low discrepancy (which means of order 1/N. One of them is the Kakutani-Fibonacci sequence.

  15. A Discrete Dynamical Model of Signed Partitions

    Directory of Open Access Journals (Sweden)

    G. Chiaselotti

    2013-01-01

    Full Text Available We use a discrete dynamical model with three evolution rules in order to analyze the structure of a partially ordered set of signed integer partitions whose main properties are actually not known. This model is related to the study of some extremal combinatorial sum problems.

  16. Polynomial Structure of Topological String Partition Functions

    CERN Document Server

    Zhou, Jie

    2015-01-01

    We review the polynomial structure of the topological string partition functions as solutions to the holomorphic anomaly equations. We also explain the connection between the ring of propagators defined from special K\\"ahler geometry and the ring of almost-holomorphic modular forms defined on modular curves.

  17. Hardware Index to Set Partition Converter

    Science.gov (United States)

    2013-01-01

    Boolean matching under permutation by efficient computation of canonical form. IEICE Trans. Fundamentals (12), 3134–3140 (2004) 6. Beeler, M., Gosper...Wesley ISBN: 0-321-58050-8 9. Kawano, S., Nakano, S.: Constant time generation of set partitions. IEICE Trans. Fundamentals E88-A(4), 930–934 (2005) 10

  18. Scalp psoriasis associated with central centrifugal cicatricial alopecia

    Directory of Open Access Journals (Sweden)

    Krista N. Larson

    2017-01-01

    Full Text Available Scalp psoriasis is a very common dermatological condition with a variety of presentations, but only rarely presents as severe alopecia. We present a case of a 50-year-old female with many years of recalcitrant hair loss that was thought to be secondary to central centrifugal cicatricial alopecia which was later diagnosed as psoriasis. This case highlights an interesting presentation and rare complication of a common disease.

  19. Dynamical system analysis of unstable flow phenomena in centrifugal blower

    Directory of Open Access Journals (Sweden)

    Garcia David

    2015-09-01

    Full Text Available Methods of dynamical system analysis were employed to analyze unsteady phenomena in a centrifugal blower. Pressure signals gathered at different control points were decomposed into their Principal Components (PCs by means of Singular Spectrum Analysis (SSA. Certain number of PCs was considered in the analysis based on their statistical correlation. Projection of the original signal onto its PCs allowed to draw the phase trajectory that clearly separated non-stable blower working conditions from its regular operation.

  20. A Review of Centrifugal Testing of Gasoline Contamination and Remediation

    OpenAIRE

    Jay N. Meegoda; Liming Hu

    2011-01-01

    Leaking underground storage tanks (USTs) containing gasoline represent a significant public health hazard. Virtually undetectable to the UST owner, gasoline leaks can contaminate groundwater supplies. In order to develop remediation plans one must know the extent of gasoline contamination. Centrifugal simulations showed that in silty and sandy soils gasoline moved due to the physical process of advection and was retained as a pool of free products above the water table. However, in clayey soi...

  1. Computational and Experimental Study of an Industrial Centrifugal Compressor Volute

    Institute of Scientific and Technical Information of China (English)

    HarriPitkanen; HannuEsa; 等

    2000-01-01

    A centrifugal compressor with a vaneless diffuser was studied experimentally and numericallly.The main target of the study was to analyze the volute flow.Two different volute geometries was studied.The numerical solution was done by using a steady-state RANS code at both design and off-design conditions.Both calculated and measured pressure and velocity distributions are presented.

  2. Centrifugal Blower for Personal Air Ventilation System (PAVS) - Phase 1

    Science.gov (United States)

    2015-02-01

    functionality. 15. SUBJECT TERMS COOLING SBIR REPORTS AXIAL FLOW FANS OFF THE SHELF EQUIPMENT BLOWERS LIGHTWEIGHT CENTRIFUGAL FORCE...HEAT STRESS (PHYSIOLOGY) AIR FLOW VENTILATION PORTABLE EQUIPMENT PERSONAL COOLING SYSTEMS EFFICIENCY EVAPORATION INTEGRATED SYSTEMS PROTOTYPES...gH Vn ad s ad s 4 1 4 3     is angular speed (2rpm) V is volumetric flow rate Had is the fan pumping head (in meters) g is the

  3. Centrifuge modeling of rocking-isolated inelastic RC bridge piers

    OpenAIRE

    Loli, Marianna; Knappett, Jonathan A; Brown, Michael J.; Anastasopoulos, Ioannis; GAZETAS, George

    2014-01-01

    Experimental proof is provided of an unconventional seismic design concept, which is based on deliberately underdesigning shallow foundations to promote intense rocking oscillations and thereby to dramatically improve the seismic resilience of structures. Termed rocking isolation, this new seismic design philosophy is investigated through a series of dynamic centrifuge experiments on properly scaled models of a modern reinforced concrete (RC) bridge pier. The experimental method reproduces th...

  4. Centrifugal stretching of 170Hf in the interacting boson model

    Directory of Open Access Journals (Sweden)

    Werner V.

    2014-03-01

    Full Text Available We present the results of a recent experiment to deduce lifetimes of members of the ground state rotational band of 170Hf, which show the effect of centrifugal stretching in this deformed isotope. Results are compared to the geometrical confined beta-soft(CBS rotor model, as well as to the interacting boson model (IBM. Two methods to correct for effects due to the finite valence space within the IBM are proposed.

  5. Comparative hemolysis study of clinically available centrifugal pumps.

    Science.gov (United States)

    Naito, K; Suenaga, E; Cao, Z L; Suda, H; Ueno, T; Natsuaki, M; Itoh, T

    1996-06-01

    Centrifugal pumps have become important devices for cardiopulmonary bypass and circulatory assistance. Five types of centrifugal pumps are clinically available in Japan. To evaluate the blood trauma caused by centrifugal pumps, a comparative hemolysis study was performed under identical conditions. In vitro hemolysis test circuits were constructed to operate the BioMedicus BP-80 (Medtronic, BioMedicus), Sarns Delphin (Sarns/3M Healthcare), Isoflow (St. Jude Medical [SJM]), HPM-15 (Nikkiso), and Capiox CX-SP45 (Terumo). The hemolysis test loop consisted of two 1.5 m lengths of polyvinyl chloride tubing with a 3/8-inch internal diameter, a reservoir with a sampling port, and a pump head. All pumps were set to flow at 6 L/min against the total pressure head of 120 mm Hg. Experiments were conducted simultaneously for 6 h at room temperature (21 degrees C) with fresh bovine blood. Blood samples for plasma-free hemoglobin testing were taken, and the change in temperature at the pump outlet port was measured during the experiment. The mean pump rotational speeds were 1,570, 1,374, 1,438, 1,944, and 1,296 rpm, and the normalized indexes of hemolysis were 0.00070, 0.00745, 0.00096, 0.00066, 0.00090 g/100 L for the BP-80, Sarns, SJM, Nikkiso, and Terumo pumps, respectively. The change in temperature at the pump outlet port was the least for the Nikkiso pump (1.8 degrees C) and the most with the SJM pump (3.8 degrees C). This study showed that there is no relationship between the pump rotational speed (rpm) and the normalized index of hemolysis in 5 types of centrifugal pumps. The pump design and number of impellers could be more notable factors in blood damage.

  6. Rubber recovery from centrifuged natural rubber latex residue using sulfuric acid

    Directory of Open Access Journals (Sweden)

    Wirach Taweepreda

    2013-04-01

    Full Text Available Waste latex sludge from centrifuged residue, which is a null by-product of concentrated latex manufacturing, wasdigested to retrieve the rubber by using sulfuric acid. It was found that the acid concentration and digestion time have aneffect on the amount and purity of the retrieved rubber. Sulfuric acid at concentrations of more than 10% by weight with adigestion time of 48 hours completely digested waste latex sludge and gave rubber 10% by weight. The quality of the retrievedrubber was examined for Mooney viscosity (MV, plasticity retention index, nitrogen content, and ash content. The averagemolecular weight of the retrieved rubber, using gel permeation chromatography, was lower than that of normal natural rubber(NR which corresponds with the MV and initial plasticity (Po. The molecular structure from Fourier transform infraredspectroscopy (FT-IR indicated that the retrieved rubber surface is wet composed with hydroxyl functional ended group.The residue solution was evaporated and crystallized. The structure of crystals was determined using power X-ray diffractometer.

  7. Prenatal centrifugation: A model for fetal programming of adult weight?

    Science.gov (United States)

    Baer, Lisa A.; Rushing, Linda; Wade, Charles E.; Ronca, April E.

    2005-08-01

    'Fetal programming' is a newly emerging field that is revealing astounding insights into the prenatal origins of adult disease, including metabolic, endocrine, and cardiovascular pathophysiology. In the present study, we tested the hypothesis that rat pups conceived, gestated and born at 2-g have significantly reduced birth weights and increased adult body weights as compared to 1-g controls. Offspring were produced by mating young adult male and female rats that were adapted to 2-g centrifugation. Female rats underwent conception, pregnancy and birth at 2-g. Newborn pups in the 2-g condition were removed from the centrifuge and fostered to non-manipulated, newly parturient dams maintained at 1-g. Comparisons were made with 1-g stationary controls, also cross- fostered at birth. As compared to 1-g controls, birth weights of pups gestated and born at 2-g were significantly reduced. Pup body weights were significantly reduced until Postnatal day (P)12. Beginning on P63, body weights of 2-g-gestated offspring exceeded those of 1-g controls by 7-10%. Thus, prenatal rearing at 2-g restricts neonatal growth and increases adult body weight. Collectively, these data support the hypothesis that 2-g centrifugation alters the intrauterine milieu, thereby inducing persistent changes in adult phenotype.

  8. Governing Principles of Alginate Microparticle Synthesis with Centrifugal Forces.

    Science.gov (United States)

    Eral, Huseyin Burak; Safai, Eric R; Keshavarz, Bavand; Kim, Jae Jung; Lee, Jisoek; Doyle, P S

    2016-07-19

    A controlled synthesis of polymeric particles is becoming increasingly important because of emerging applications ranging from medical diagnostics to self-assembly. Centrifugal synthesis of hydrogel microparticles is a promising method, combining rapid particle synthesis and the ease of manufacturing with readily available laboratory equipment. This method utilizes centrifugal forces to extrude an aqueous polymer solution, sodium alginate (NaALG) through a nozzle. The extruded solution forms droplets that quickly cross-link upon contact with aqueous calcium chloride (CaCl2) solution to form hydrogel particles. The size distribution of hydrogel particles is dictated by the pinch-off behavior of the extruded solution through a balance of inertial, viscous, and surface tension stresses. We identify the parameters dictating the particle size and provide a numerical correlation predicting the average particle size. Furthermore, we create a phase map identifying different pinch-off regimes (dripping without satellites, dripping with satellites, and jetting), explaining the corresponding particle size distributions, and present scaling arguments predicting the transition between regimes. By shedding light on the underlying physics, this study enables the rational design and operation of particle synthesis by centrifugal forces.

  9. Numerical Analysis and Centrifuge Modeling of Shallow Foundations

    Institute of Scientific and Technical Information of China (English)

    罗强; 栾茂田; 杨蕴明; 王忠涛; 赵守正

    2014-01-01

    The influence of non-coaxial constitutive model on predictions of dense sand behavior is investigated in this paper. The non-coaxial model with strain softening plasticity is applied into finite-element program ABAQUS, which is first used to predict the stress-strain behavior and the non-coaxial characteristic between the orientations of the principal stress and principal plastic strain rate in simple shear tests. The model is also used to predict load settlement responses and bearing capacity factors of shallow foundations. A series of centrifuge tests for shallow foundations on saturated dense sand are performed under drained conditions and the test results are compared with the corresponding numerical results. Various footing dimensions, depths of embedment, and footing shapes are considered in these tests. In view of the load settlement relationships, the stiffness of the load-displacement curves is significantly affected by the non-coaxial model compared with those predicted by the coaxial model, and a lower value of non-coaxial modulus gives a softer response. Considering the soil behavior at failure, the coaxial model predictions of bearing capacity factors are more advanced than those of centrifuge test results and the non-coaxial model results;besides, the non-coaxial model gives better predictions. The non-coaxial model predictions are closer to those of the centrifuge results when a proper non-coaxial plastic modulus is chosen.

  10. Low-molecular weight plasma proteome analysis using centrifugal ultrafiltration.

    Science.gov (United States)

    Greening, David W; Simpson, Richard J

    2011-01-01

    The low-molecular weight fraction (LMF) of the human plasma proteome is an invaluable source of biological information, especially in the context of identifying plasma-based biomarkers of disease. This protocol outlines a standardized procedure for the rapid/reproducible LMF profiling of human plasma samples using centrifugal ultrafiltration fractionation, followed by 1D-SDS-PAGE separation and nano-LC-MS/MS. Ultrafiltration is a convective process that uses anisotropic semipermeable membranes to separate macromolecular species on the basis of size. We have optimized centrifugal ultrafiltration for plasma fractionation with respect to buffer and solvent composition, centrifugal force, duration and temperature to facilitate >95% recovery, and enrichment of low-M (r) components from human plasma. Using this protocol, >260 unique peptides can be identified from a single plasma profiling experiment using 100 μL of plasma (Greening and Simpson, J Proteomics 73:637-648, 2010). The efficacy of this method is demonstrated by the identification, for the first time, of several plasma proteins (e.g., protein KIAA0649 (Q9Y4D3), rheumatoid factor D5, serine protease inhibitor A3, and transmembrane adapter protein PAG) previously not reported in extant high-confidence Human Proteome Organization Plasma Proteome Project datasets.

  11. Subchronic centrifugal mechanical assist in an unheparinized calf model.

    Science.gov (United States)

    Wagner-Mann, C; Curtis, J; Mann, F A; Turk, J; Demmy, T; Turpin, T

    1996-06-01

    The purpose of this study was to determine whether the major centrifugal pumps currently in use in the United States (Medtronic, BioMedicus BioPump and Carmeda-coated BioPump, Sarns 3M centrifugal pump, and St. Jude Medical Lifestream) could function as left mechanical assist devices in the subchronic (72 h) unheparinized calf model. Calves were instrumented for left atrial to aorta ex vivo assist, and the pump flow was set at 3.5 +/- 0.4 L/min. Two calves (Sarns 3M and St. Jude) survived 72 h of pumping without clinical complications. The other 2 calves died at 62 and 66 h (Medtronic BioPump and Carmeda-coated BioPump, respectively); both had pelvic limb paralysis. The seal of the Sarns 3M pump head ruptured after approximately 36 h of pumping and required replacement. On postmortem examination, pump-associated thromboembolic lesions were detected in 3 of the 4 calves in one or more of the following organs: kidneys, pancreas, abomasum, duodenum, ileum, spleen, and lumbar spinal cord. The calf with the Sarns 3M pump had no discernable lesions. Because of the clinical abnormalities and postmortem lesions in the unheparinized calf model, it was suggested that anticoagulation is necessary for conducting centrifugal mechanical assist studies in calves using presently available technology.

  12. Modelling of horizontal centrifugal casting of work roll

    Science.gov (United States)

    Xu, Zhian; Song, Nannan; Tol, Rob Val; Luan, Yikun; Li, Dianzhong

    2012-07-01

    A numerical model to simulate horizontal centrifugal roll castings is presented in this paper. In order to simulate the flow fluid and solidification of horizontal centrifugal roll casting correctly, the model uses a body fitted mesh technique to represent the geometry. This new method maps a plate layer mesh to a circular mesh. The smooth body fitted mesh method gives more accurate calculation results for cylindrical geometries. A velocity depending on the angular velocity and inner radius of the mould is set up as a velocity boundary condition. The fluid flow coupled with heat transfer and solidification in a rapidly rotating roll is simulated. A gravity free falling method is applied as a pouring condition. A moveable pouring system is also used in the simulations. High speed steel is used to produce the work roll. Two different gating positions and a moveable gating system are simulated in this paper. Results show that the position of pouring system has a significant influence on the temperature distribution. The temperature distribution at a fixed central pouring system is more favourable than the distribution from a side pouring system. A moving gating system method is a better way to obtain a uniform temperature field in centrifugal casting and offers an alternative for existing techniques.

  13. Effect of centrifugal forces on dimensional error of bored shapes

    Science.gov (United States)

    Arsuaga, M.; de Lacalle, L. N. López; Lobato, R.; Urbikain, G.; Campa, F.

    2012-04-01

    Boring operations of deep holes with a slender boring bar are often hindered by the precision because of their low static stiffness and high deformations. Because of that, it is not possible to remove much larger depths of cuts than the nose radius of the tool, unlike the case of turning and face milling operations, and consequently, the relationship between the cutting force distribution, tool geometry, feed rate and depth of cut becomes non-linear and complex. This problem gets worse when working with a rotating boring head where apart from the cutting forces and the variation of the inclination angle because of shape boring, the bar and head are affected by de centrifugal forces. The centrifugal forces, and therefore the centrifugal deflection, will vary as a function of the rotating speed, boring bar mass distribution and variable radial position of the bar in shape boring. Taking in to account all this effects, a load and deformation model was created. This model has been experimentally validated to use as a corrector factor of the radial position of the U axis in the boring head.

  14. Aqueous two-phase partition applied to the isolation of plasma membranes and Golgi apparatus from cultured mammalian cells

    Science.gov (United States)

    Morre, D. M.; Morre, D. J.

    2000-01-01

    Partitioning in dextran-poly(ethylene)glycol (PEG) aqueous-aqueous phase systems represents a mature technology with many applications to separations of cells and to the preparation of membranes from mammalian cells. Most applications to membrane isolation and purification have focused on plasma membranes, plasma membrane domains and separation of right side-out and inside-out plasma membrane vesicles. The method exploits a combination of membrane properties, including charge and hydrophobicity. Purification is based upon differential distributions of the constituents in a sample between the two principal compartments of the two phases (upper and lower) and at the interface. The order of affinity of animal cell membranes for the upper phase is: endoplasmic reticulum two-phase partition with other procedures to obtain a more highly purified preparation. A procedure is described for preparation of Golgi apparatus from transformed mammalian cells that combines aqueous two-phase partition and centrifugation. Also described is a periodic NADH oxidase, a new enzyme marker for right side-out plasma membrane vesicles not requiring detergent disruptions for measurement of activity.

  15. Open software tools for eddy covariance flux partitioning

    Science.gov (United States)

    Agro-ecosystem management and assessment will benefit greatly from the development of reliable techniques for partitioning evapotranspiration (ET) into evaporation (E) and transpiration (T). Among other activities, flux partitioning can aid in evaluating consumptive vs. non-consumptive agricultural...

  16. The importance of applying an appropriate data partitioning

    CERN Document Server

    Dimitrov, Gancho; The ATLAS collaboration

    2015-01-01

    In this presentation are described specific technical solutions put in place in various database applications of the ATLAS experiment at LHC where we make use of several partitioning techniques available in Oracle 11g. With the broadly used range partitioning and its option of automatic interval partitioning we add our own logic in PLSQL procedures and scheduler jobs to sustain data sliding windows in order to enforce various data retention policies. We also make use of the new Oracle 11g reference partitioning in the ATLAS Nightly Build System to achieve uniform data segmentation. However the most challenging was to segment the data of the new ATLAS Distributed Data Management system, which resulted in tens of thousands list type partitions and sub-partitions. Partition and sub-partition management, index strategy, statistics gathering and queries execution plan stability are important factors when choosing an appropriate physical model for the application data management. The so-far accumulated knowledge wi...

  17. Microstructures of Al-Al3Ti functionally graded materials fabricated by centrifugal solid-particle method and centrifugal in situ method

    Science.gov (United States)

    Watanabe, Yoshimi; Zhou, Qi; Sato, Hisashi; Fujii, Toshiyuki; Inamura, Tomonari

    2017-01-01

    Methods of fabrication by centrifugal casting for functionally graded materials (FGMs) can be classified into two categories on the basis of the relationship between the process temperature and the liquidus temperature of a master alloy. They are the centrifugal solid-particle method and centrifugal in situ method, which could be carried out at process temperatures lower and higher than the liquidus temperature of the master alloy, respectively. In a previous study, it was found that the microstructures of Al-Al3Ti FGMs fabricated by the centrifugal in situ method processed at 1600 °C were different from those fabricated by the centrifugal solid-particle method processed at 800 °C. Although it is expected that the FGMs fabricated by the centrifugal in situ method processed at approximately the liquidus temperature should show extraordinary microstructures, those microstructures have not been observed. In this study, the microstructures of Al-Al3Ti FGMs fabricated at 1000 °C (centrifugal solid-particle method) and 1200 °C (centrifugal in situ method) were investigated.

  18. Water Drainage from Unsaturated Soils in a Centrifuge Permeameter

    Science.gov (United States)

    Ornelas, G.; McCartney, J.; Zhang, M.

    2013-12-01

    This study involves an analysis of water drainage from an initially saturated silt layer in a centrifuge permeameter to evaluate the hydraulic properties of the soil layer in unsaturated conditions up to the point where the water phase becomes discontinuous. These properties include the soil water retention curve (SWRC) and the hydraulic conductivity function (HCF). The hydraulic properties of unsaturated silt are used in soil-atmosphere interaction models that take into account the role of infiltration and evaporation of water from soils due to atmospheric interaction. These models are often applied in slope stability analyses, landfill cover design, aquifer recharge analyses, and agricultural engineering. The hydraulic properties are also relevant to recent research concerning geothermal heating and cooling, as they can be used to assess the insulating effects of soil around underground heat exchangers. This study employs a high-speed geotechnical centrifuge to increase the self-weight of a compacted silt specimen atop a filter plate. Under a centrifuge acceleration of N times earth's gravity, the concept of geometric similitude indicates that the water flow process in a small-scale soil layer will be similar to those in a soil layer in the field that is N times thicker. The centrifuge acceleration also results in an increase in the hydraulic gradient across the silt specimen, which causes water to flow out of the pores following Darcy's law. The drainage test was performed until the rate of liquid water flow out of the soil layer slowed to a negligible level, which corresponds to the transition point at which further water flow can only occur due to water vapor diffusion following Fick's law. The data from the drainage test in the centrifuge were used to determine the SWRC and HCF at different depths in the silt specimen, which compared well with similar properties defined using other laboratory tests. The transition point at which liquid water flow stopped (and

  19. Optimising query execution time in LHCb Bookkeeping System using partition pruning and Partition-Wise joins

    Science.gov (United States)

    Mathe, Zoltan; Charpentier, Philippe

    2014-06-01

    The LHCb experiment produces a huge amount of data which has associated metadata such as run number, data taking condition (detector status when the data was taken), simulation condition, etc. The data are stored in files, replicated on the Computing Grid around the world. The LHCb Bookkeeping System provides methods for retrieving datasets based on their metadata. The metadata is stored in a hybrid database model, which is a mixture of Relational and Hierarchical database models and is based on the Oracle Relational Database Management System (RDBMS). The database access has to be reliable and fast. In order to achieve a high timing performance, the tables are partitioned and the queries are executed in parallel. When we store large amounts of data the partition pruning is essential for database performance, because it reduces the amount of data retrieved from the disk and optimises the resource utilisation. This research presented here is focusing on the extended composite partitioning strategy such as range-hash partition, partition pruning and usage of the Partition-Wise joins. The system has to serve thousands of queries per minute, the performance and capability of the system is measured when the above performance optimization techniques are used.

  20. Using Reward/Utility Based Impact Scores in Partitioning

    Science.gov (United States)

    2014-05-01

    ing approach called Reward/Utility-Based Impact ( RUBI ). RUBI nds an e ective partitioning of agents while requir- ing no prior domain knowledge...provides better performance by discovering a non-trivial agent partitioning, and leads to faster simulations. We test RUBI in the Air Tra c Flow Management...partitioning with RUBI in the ATFMP, there is a 37% increase in per- formance, with a 510x speed up per simulation step over non-partitioning approaches

  1. Analysis of pesticide residues in tobacco with online size exclusion chromatography with gas chromatography and tandem mass spectrometry.

    Science.gov (United States)

    Guo, Weiyun; Bian, Zhaoyang; Tang, Gangling; Wang, Deguo; Li, Guanghui; Wang, Jianlong

    2016-07-01

    An ultrasensitive method for the simultaneous analysis of pesticides residues in tobacco was developed with online size exclusion chromatography with gas chromatography and tandem mass spectrometry. Tobacco samples were extracted with the solvent mixture of cyclohexane and acetone (7:3, v/v) and centrifuged. Then, the supernatant liquors were injected directly into the online size exclusion chromatography with gas chromatography and tandem mass spectrometry without any other purification procedures after being filtered with a 0.22 μm organic phase filter. The matrix interferences were effectively removed and recoveries of most pesticides were in the range of 72-121%. Especially, for chlorothalonil, the analysis efficiency of this method was much more favorable than that of the general method, in which dispersive solid-phase extraction was used as an additional purified procedure. In addition, the limits of quantitation of this method were from 1 to 50 μg/kg. Therefore, a rapid, cost-effective, labor-saving method was proposed in the present work, which was suitable for the analysis of 41 pesticide residues in tobacco.

  2. GPU Acceleration of Graph Matching, Clustering, and Partitioning

    NARCIS (Netherlands)

    Fagginger Auer, B.O.

    2013-01-01

    We consider sequential algorithms for hypergraph partitioning and GPU (i.e., fine-grained shared-memory parallel) algorithms for graph partitioning and clustering. Our investigation into sequential hypergraph partitioning is concerned with the efficient construction of high-quality matchings for hyp

  3. Spectral partitioning of random regular blockmodels

    CERN Document Server

    Barucca, Paolo

    2016-01-01

    Graph partitioning problems emerge in a wide variety of complex systems, ranging from biology to finance, but can be rigorously analyzed and solved only for a few graph ensembles. Here, an ensemble of random graphs with regular block structure is introduced, for which analytical results can be obtained. In particular, the spectral density of such random regular blockmodels is computed exactly for a modular, bipartite and core-periphery structure. McKay's law for random regular graphs is found analytically to apply also for regular modular and bipartite structures when blocks are homogeneous. In core-periphery structures, where blocks are intrinsically heterogeneous, a new law is found to apply for the spectral density. Exact solution to the inference problem is provided for the models discussed. All analytical results show perfect agreement with numerical experiments. Final discussion summarizes results and outlines the relevance of the results for the solution of graph partitioning problems in other graph en...

  4. Partition-DFT on the Water Dimer

    CERN Document Server

    Gómez, Sara; Restrepo, Albeiro; Wasserman, Adam

    2016-01-01

    As is well known, the ground-state symmetry group of the water dimer switches from its equilibrium $C_{s}$-character to $C_{2h}$-character as the distance between the two oxygen atoms of the dimer decreases below $R_{\\rm O-O}\\sim 2.5$ \\AA{}. For a range of $R_{\\rm O-O}$ between 1 and 5 \\AA{}, and for both symmetries, we apply Partition Density Functional Theory (PDFT) to find the unique monomer densities that sum to the correct dimer densities while minimizing the sum of the monomer energies. We calculate the work involved in deforming the isolated monomer densities and find that it is slightly larger for the $C_s$ geometry for all $R_{\\rm O-O}$. We discuss how the PDFT densities and the corresponding partition potentials support the orbital-interaction picture of hydrogen-bond formation.

  5. An exact algorithm for graph partitioning

    CERN Document Server

    Hager, William; Zhang, Hongchao

    2009-01-01

    An exact algorithm is presented for solving edge weighted graph partitioning problems. The algorithm is based on a branch and bound method applied to a continuous quadratic programming formulation of the problem. Lower bounds are obtained by decomposing the objective function into convex and concave parts and replacing the concave part by an affine underestimate. It is shown that the best affine underestimate can be expressed in terms of the center and the radius of the smallest sphere containing the feasible set. The concave term is obtained either by a constant diagonal shift associated with the smallest eigenvalue of the objective function Hessian, or by a diagonal shift obtained by solving a semidefinite programming problem. Numerical results show that the proposed algorithm is competitive with state-of-the-art graph partitioning codes.

  6. Supersymmetric partition functions on Riemann surfaces

    CERN Document Server

    Benini, Francesco

    2016-01-01

    We present a compact formula for the supersymmetric partition function of 2d N=(2,2), 3d N=2 and 4d N=1 gauge theories on $\\Sigma_g \\times T^n$ with partial topological twist on $\\Sigma_g$, where $\\Sigma_g$ is a Riemann surface of arbitrary genus and $T^n$ is a torus with n=0,1,2, respectively. In 2d we also include certain local operator insertions, and in 3d we include Wilson line operator insertions along $S^1$. For genus g=1, the formula computes the Witten index. We present a few simple Abelian and non-Abelian examples, including new tests of non-perturbative dualities. We also show that the large N partition function of ABJM theory on $\\Sigma_g \\times S^1$ reproduces the Bekenstein-Hawking entropy of BPS black holes in AdS4 whose horizon has $\\Sigma_g$ topology.

  7. Non-parametric partitioning of SAR images

    Science.gov (United States)

    Delyon, G.; Galland, F.; Réfrégier, Ph.

    2006-09-01

    We describe and analyse a generalization of a parametric segmentation technique adapted to Gamma distributed SAR images to a simple non parametric noise model. The partition is obtained by minimizing the stochastic complexity of a quantized version on Q levels of the SAR image and lead to a criterion without parameters to be tuned by the user. We analyse the reliability of the proposed approach on synthetic images. The quality of the obtained partition will be studied for different possible strategies. In particular, one will discuss the reliability of the proposed optimization procedure. Finally, we will precisely study the performance of the proposed approach in comparison with the statistical parametric technique adapted to Gamma noise. These studies will be led by analyzing the number of misclassified pixels, the standard Hausdorff distance and the number of estimated regions.

  8. Nested partitions method, theory and applications

    CERN Document Server

    Shi, Leyuan

    2009-01-01

    There is increasing need to solve large-scale complex optimization problems in a wide variety of science and engineering applications, including designing telecommunication networks for multimedia transmission, planning and scheduling problems in manufacturing and military operations, or designing nanoscale devices and systems. Advances in technology and information systems have made such optimization problems more and more complicated in terms of size and uncertainty. Nested Partitions Method, Theory and Applications provides a cutting-edge research tool to use for large-scale, complex systems optimization. The Nested Partitions (NP) framework is an innovative mix of traditional optimization methodology and probabilistic assumptions. An important feature of the NP framework is that it combines many well-known optimization techniques, including dynamic programming, mixed integer programming, genetic algorithms and tabu search, while also integrating many problem-specific local search heuristics. The book uses...

  9. Partitioning Complete Graphs by Heterochromatic Trees

    Institute of Scientific and Technical Information of China (English)

    Ze-min JIN; Xue-liang LI

    2012-01-01

    A heterochromatic tree is an edge-colored tree in which any two edges have different colors.The heterochroratic tree partition number of an r-edge-colored graph G,denoted by tr(G),is the minimum positive integer p such that whenever the edges of the graph G are colored with r colors,the vertices of G can be covered by at most p vertex-disjoint heterochromatic trees.In this paper we determine the heterochromatic tree partition number of r-edge-colored complete graphs.We also find at most tr(Kn) vertex-disjoint heterochromatic trees to cover all the vertices in polynomial time for a given r-edge-coloring of Kn.

  10. Analysis of fractals with combined partition

    Science.gov (United States)

    Dedovich, T. G.; Tokarev, M. V.

    2016-03-01

    The space—time properties in the general theory of relativity, as well as the discreteness and non-Archimedean property of space in the quantum theory of gravitation, are discussed. It is emphasized that the properties of bodies in non-Archimedean spaces coincide with the properties of the field of P-adic numbers and fractals. It is suggested that parton showers, used for describing interactions between particles and nuclei at high energies, have a fractal structure. A mechanism of fractal formation with combined partition is considered. The modified SePaC method is offered for the analysis of such fractals. The BC, PaC, and SePaC methods for determining a fractal dimension and other fractal characteristics (numbers of levels and values of a base of forming a fractal) are considered. It is found that the SePaC method has advantages for the analysis of fractals with combined partition.

  11. Hypergraph Partitioning through Vertex Separators on Graphs

    CERN Document Server

    Kayaaslan, Enver; Catalyurek, Umit V; Aykanat, Cevdet

    2011-01-01

    The modeling flexibility provided by hypergraphs has drawn a lot of interest from the combinatorial scientific community, leading to novel models and algorithms, their applications, and development of associated tools. Hypergraphs are now a standard tool in combinatorial scientific computing. The modeling flexibility of hypergraphs however, comes at a cost: algorithms on hypergraphs are inherently more complicated than those on graphs, which sometimes translate to nontrivial increases in processing times. Neither the modeling flexibility of hypergraphs, nor the runtime efficiency of graph algorithms can be overlooked. Therefore, the new research thrust should be how to cleverly trade-off between the two. This work addresses one method for this trade-off by solving the hypergraph partitioning problem by finding vertex separators on graphs. Specifically, we investigate how to solve the hypergraph partitioning problem by seeking a vertex separator on its net intersection graph (NIG), where each net of the hyperg...

  12. Integrated use of ultra scale-down and financial modeling to identify optimal conditions for the precipitation and centrifugal recovery of milk proteins.

    Science.gov (United States)

    Chhatre, Sunil; Pampel, Lars; Titchener-Hooker, Nigel J

    2011-07-01

    This article investigates the integrated application of ultra scale-down (USD) techniques and economic modeling as a means for identifying optimal bioprocess operating conditions. The benefits of the approach are illustrated for the recovery of lactoperoxidase (LPO) from bovine milk. In the process, milk is skimmed to deplete its lipid content, before being subjected to low pH incubation with acetic acid in order to precipitate the primary impurity (casein). Following removal of the solids by disk stack centrifugation, pH adjustment and filtration, cation exchange chromatography is used as a positive mode column step to bind the LPO before it is polished and freeze dried. An economic model of this process was used to identify where greatest product loss occurs and hence where the largest opportunity cost was being incurred. Scale-down analysis was used to characterize the influence of the critical steps, identified as precipitation and centrifugation, upon LPO recovery. A mathematical model was used to relate the centrifuge feed flowrate and discharge interval to the supernatant yield, and it was shown that increasing the centrifugal solids residence time achieved superior solids de-watering and so higher product yield, although this also increased the overall processing time. To resolve this conflict, scale-down data were used again in conjunction with an economic model to determine the most suitable conditions that maximized annual profit and minimized operating costs. The results demonstrate the power of combining USD data with models of economic and process performance in order to establish the best overall operating strategies for biopharmaceutical manufacture.

  13. Partition of polycyclic aromatic hydrocarbons on organobentonites

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A series of organobentonites synthesized by exchanging organiccation such as dodecyltri-methylammonium (DTMA),benzyldimethyltetradecylammonium (BDTDA), cetyltrimethyl-ammonium (CTMA), octodeyltrimethylammonium (OTMA) on bentonite. The optimal condition, properties and mechanisms for the organobentonites to sorb phenanthrene, anthracene, naphthalene, acenaphthene in water were investigated in detail. The partition behavior was determined for four polycyclic aromatic hydrocarbons (PAHs), such as naphthalene, phenanthrene, anthracene and acenaphthene, from water to a series of organobentonites. The interlayer spacings and organic carbon contents of organobentonites, removal rate and sorption capacities for organobentonites to treat phenanthrene,anthracene, naphthalene, acenaphthene were correlated to the length of alkyl chains and the amounts of cation surfactant exchanged on Foundation item: the bentonite. Phenanthrene, anthracene, naphthalene, and acenaphthene sorption to organobentonites were characterized by linear isotherms, indicating solute partition between water and the organic phase composed of the large alkyl functional groups of quaternary ammonium cations. PAHs distribution coefficients (Kd)between organobentonites and water were proportional to the organic carbon contents of organobentonites. However, the partition coefficients (Koc) were nearly constants for PAHs in the system of organobentonite-water. The Koc of phenanthrene, anthracene,naphthalene, acenaphthene were 2.621x105, 2.106x105, 2.247x104,5.085x104, respectively. The means Koc values on the organobentonites are about ten to twenty times larger than the values on the soils/sediments, what is significant prerequisite for organobentonite to apply to remediation of pollution soil and groundwater. The sorption mechanism was also evaluated from octanol-water partition coefficients and aqueous solubility of PAHs. The correlations between lgKoc and 1gkow, 1gKoc and 1gS for PAHs in the system of water

  14. Metal partitioning and toxicity in sewage sludge

    Energy Technology Data Exchange (ETDEWEB)

    Carlson-Ekvall, C.E.A.; Morrison, G.M. [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Sanitary Engineering

    1995-12-31

    Over 20 years of research has failed to provide an unequivocal correlation between chemically extracted metals in sewage sludge applied to agricultural soil and either metal toxicity to soil organisms or crop uptake. Partitioning of metals between phases and species can provide a better estimation of mobility and potential bioavailability. Partition coefficients, K{sub D} for Cd, Cu, Pb and Zn in a sludge/water solution were determined considering the sludge/water solution as a three-phase system (particulate, colloidal and electrochemically available) over a range of pH values, ionic strengths, contact times and sludge/water ratios and compared with the KD values for sludge/water solution as a two-phase system (aqueous phase and particulate phase). Partitioning results were interpreted in terms of metal mobility from sludge to colloids and in terms of potential bioavailability from colloids to electrochemically available. The results show that both mobility and potential bioavailability are high for Zn, while Cu partitions into the mobile colloidal phase which is relatively non-bioavailable. Lead is almost completely bound to the solid phase, and is neither mobile nor bioavailable. A comparison between K, values and toxicity shows that Zn in sludge is more toxic than can be accounted for in the aqueous phase, which can be due to synergistic effects between sludge organics and Zn. Copper demonstrates clear synergism which can be attributed to the formation of lipid-soluble Cu complexes with known sludge components such as LAS, caffeine, myristic acid and nonylphenol.

  15. Recursive formulae for the multiplicative partition function

    Directory of Open Access Journals (Sweden)

    Jun Kyo Kim

    1999-01-01

    Full Text Available For a positive integer n, let f(n be the number of essentially different ways of writing n as a product of factors greater than 1, where two factorizations of a positive integer are said to be essentially the same if they differ only in the order of the factors. This paper gives a recursive formula for the multiplicative partition function f(n.

  16. Enriched surface acidity for surfactant-free suspensions of carboxylated carbon nanotubes purified by centrifugation

    Directory of Open Access Journals (Sweden)

    Elizabeth I. Braun

    2016-06-01

    Full Text Available It is well known that surfactant-suspended carbon nanotube (CNT samples can be purified by centrifugation to decrease agglomerates and increase individually-dispersed CNTs. However, centrifugation is not always part of protocols to prepare CNT samples used in biomedical applications. Herein, using carboxylated multi-walled CNTs (cMWCNTs suspended in water without a surfactant, we developed a Boehm titrimetric method for the analysis of centrifuged cMWCNT suspensions and used it to show that the surface acidity of oxidized carbon materials in aqueous cMWCNT suspensions was enriched by ∼40% by a single low-speed centrifugation step. This significant difference in surface acidity between un-centrifuged and centrifuged cMWCNT suspensions has not been previously appreciated and is important because the degree of surface acidity is known to affect the interactions of cMWCNTs with biological systems.

  17. Bioreactor-free tissue engineering: directed tissue assembly by centrifugal casting.

    Science.gov (United States)

    Mironov, Vladimir; Kasyanov, Vladimir; Markwald, Roger R; Prestwich, Glenn D

    2008-02-01

    Casting is a process by which a material is introduced into a mold while it is liquid, allowed to solidify in a predefined shape inside the mold, and then removed to give a fabricated object, part or casing. Centrifugal casting could be defined as a process of molding using centrifugal forces. Although the centrifugal casting technology has a long history in metal manufacturing and in the plastics industry, only recently has this technology attracted the attention of tissue engineers. Initially, centrifugation was used to optimize cell seeding on a solid scaffold. More recently, centrifugal casting has been used to create tubular scaffolds and both tubular and flat multilayered, living tissue constructs. These newer applications were enabled by a new class of biocompatible in situ crosslinkable hydrogels that mimic the extracellular matrix. Herein the authors summarize the state of the art of centrifugal casting technology in tissue engineering, they outline associated technological challenges, and they discuss the potential future for clinical applications.

  18. SCORE SETS IN ORIENTED 3-PARTITE GRAPHS

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Let D(U, V, W) be an oriented 3-partite graph with |U|=p, |V|=q and |W|= r. For any vertex x in D(U, V, W), let d+x and d-x be the outdegree and indegree of x respectively. Define aui (or simply ai) = q + r + d+ui - d-ui, bvj(or simply bj) = p + r + d+vj - d-vj and Cwk (or simply ck) = p + q + d+wk - d-wk as the scores of ui in U, vj in V and wk in Wrespectively. The set A of distinct scores of the vertices of D(U, V, W) is called its score set. In this paper, we prove that if a1 is a non-negative integer, ai(2≤i≤n - 1) are even positive integers and an is any positive integer, then for n≥3, there exists an oriented 3-partite graph with the score set A = {a1,2∑i=1 ai,…,n∑i=1 ai}, except when A = {0,2,3}. Some more results for score sets in oriented 3-partite graphs are obtained.

  19. Polymers as Reference Partitioning Phase: Polymer Calibration for an Analytically Operational Approach To Quantify Multimedia Phase Partitioning.

    Science.gov (United States)

    Gilbert, Dorothea; Witt, Gesine; Smedes, Foppe; Mayer, Philipp

    2016-06-07

    Polymers are increasingly applied for the enrichment of hydrophobic organic chemicals (HOCs) from various types of samples and media in many analytical partitioning-based measuring techniques. We propose using polymers as a reference partitioning phase and introduce polymer-polymer partitioning as the basis for a deeper insight into partitioning differences of HOCs between polymers, calibrating analytical methods, and consistency checking of existing and calculation of new partition coefficients. Polymer-polymer partition coefficients were determined for polychlorinated biphenyls (PCBs), polycyclic aromatic hydrocarbons (PAHs), and organochlorine pesticides (OCPs) by equilibrating 13 silicones, including polydimethylsiloxane (PDMS) and low-density polyethylene (LDPE) in methanol-water solutions. Methanol as cosolvent ensured that all polymers reached equilibrium while its effect on the polymers' properties did not significantly affect silicone-silicone partition coefficients. However, we noticed minor cosolvent effects on determined polymer-polymer partition coefficients. Polymer-polymer partition coefficients near unity confirmed identical absorption capacities of several PDMS materials, whereas larger deviations from unity were indicated within the group of silicones and between silicones and LDPE. Uncertainty in polymer volume due to imprecise coating thickness or the presence of fillers was identified as the source of error for partition coefficients. New polymer-based (LDPE-lipid, PDMS-air) and multimedia partition coefficients (lipid-water, air-water) were calculated by applying the new concept of a polymer as reference partitioning phase and by using polymer-polymer partition coefficients as conversion factors. The present study encourages the use of polymer-polymer partition coefficients, recognizing that polymers can serve as a linking third phase for a quantitative understanding of equilibrium partitioning of HOCs between any two phases.

  20. Topological analysis of the formation of Jet-Wake flow pattern in centrifugal impeller channel

    Institute of Scientific and Technical Information of China (English)

    ZHENG Qun; LIU Shun-long

    2004-01-01

    Topological analyses are carried out for the numerical results of internal flow field in centrifugal impeller. Topological rules of the singular point characteristics of the limiting streamline are derived and used to determine three dimensional separation patterns in centrifugal impeller and to verify the numerical results. The results reveal that the wake is saddle to nodal closed separation and the formation, its onset point and its developing process of Jet-Wake Flow pattern in centrifugal impeller are presented in this paper.

  1. Mathematical model of the component mixture distribution in the molten cast iron during centrifugation (sedimentation)

    Science.gov (United States)

    Bikulov, R. A.; Kotlyar, L. M.

    2014-12-01

    For the development and management of the manufacturing processes of axisymmetric articles with compositional structure by centrifugal casting method [1,2,3,4] is necessary to create a generalized mathematical model of the dynamics of component mixture in the molten cast iron during centrifugation. In article. based on the analysis of the dynamics of two-component mixture at sedimentation, a method of successive approximations to determine the distribution of a multicomponent mixture by centrifugation in a parabolic crucible is developed.

  2. Methods of observation of the centrifugal quantum states of neutrons

    Science.gov (United States)

    Cubitt, R.; Nesvizhevsky, V. V.; Petukhov, A. K.; Voronin, A. Yu.; Pignol, G.; Protasov, K. V.; Gurshijants, P.

    2009-12-01

    We propose methods for observation of the quasi-stationary states of neutrons, localized near a curved mirror surface. The bounding effective well is formed by the centrifugal potential and the mirror's optical potential. This phenomenon is an example of an exactly solvable "quantum bouncer" problem that can be studied experimentally. It could provide a new tool for studying fundamental neutron-matter interactions, neutron quantum optics and surface physics effects. The feasibility of observation of such quantum states has been proven in first experiments.

  3. Methods of observation of the centrifugal quantum states of neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Cubitt, R. [Institut Laue-Langevin (ILL), 6 rue Jules Horowitz, F-38042 Grenoble (France); Nesvizhevsky, V.V., E-mail: nesvizhevsky@ill.e [Institut Laue-Langevin (ILL), 6 rue Jules Horowitz, F-38042 Grenoble (France); Petukhov, A.K. [Institut Laue-Langevin (ILL), 6 rue Jules Horowitz, F-38042 Grenoble (France); Voronin, A.Yu., E-mail: dr.a.voronin@gmail.co [P.N. Lebedev Physical Institute, 53 Leninsky Prospekt, 119991 Moscow (Russian Federation); Pignol, G.; Protasov, K.V. [Laboratoire de Physique Subatomique et de Cosmologie (LPSC), IN2P3-CNRS, UJF, 53, Avenue des Martyrs, F-38026 Grenoble (France); Gurshijants, P. [Institute of Solid State Physics (ISSP), Institutskaya Street 2, 142432 Chernogolovka, Moscow Region (Russian Federation)

    2009-12-11

    We propose methods for observation of the quasi-stationary states of neutrons, localized near a curved mirror surface. The bounding effective well is formed by the centrifugal potential and the mirror's optical potential. This phenomenon is an example of an exactly solvable 'quantum bouncer' problem that can be studied experimentally. It could provide a new tool for studying fundamental neutron-matter interactions, neutron quantum optics and surface physics effects. The feasibility of observation of such quantum states has been proven in first experiments.

  4. Capture into resonance and phase space dynamics in optical centrifuge

    CERN Document Server

    Armon, Tsafrir

    2016-01-01

    The process of capture of a molecular enesemble into rotational resonance in the optical centrifuge is investigated. The adiabaticity and phase space incompressibility are used to find the resonant capture probability in terms of two dimensionless parameters P1,P2 characterising the driving strength and the nonlinearity, and related to three characteristic time scales in the problem. The analysis is based on the transformation to action-angle variables and the single resonance approximation, yielding reduction of the three-dimensional rotation problem to one degree of freedom. The analytic results for capture probability are in a good agreement with simulations. The existing experiments satisfy the validity conditions of the theory.

  5. Centrifugal experimental study of suction bucket foundations under dynamic loading

    Science.gov (United States)

    Lu, Xiaobing; Wu, Yongren; Jiao, Bintian; Wang, Shuyun

    2007-12-01

    Centrifugal experiments were carried out to investigate the responses of suction bucket foundations under horizontal and vertical dynamic loading. It is shown that when the loading amplitude is over a critical value, the sand at the upper part around the bucket is softened or even liquefied. The excess pore pressure decreases from the upper part to the lower part of the sand layer in the vertical direction and decreases radially from the bucket’s side wall in the horizontal direction. Large settlements of the bucket and the sand layer around the bucket are induced by dynamic loading. The dynamic responses of the bucket with smaller height (the same diameter) are heavier.

  6. Silver nanodisks: size selection via centrifugation and optical properties.

    Science.gov (United States)

    Germain, V; Brioude, A; Ingert, D; Pileni, M P

    2005-03-22

    Silver nanodisks, having two different sizes, and spherical particles are synthesized by soft chemistry. By using centrifugation, nanodisks are mainly selected. The experimental absorption spectra of these nanodisks with different sizes are compared to those simulated using the discrete dipole approximation method. For small nanodisk sizes, the nanodisk shape is neglected and the simulated spectra closest to the experiments are obtained by assuming a spheroidal particle. Conversely, for larger nanodisks, the precise geometries represented by snip and aspect ratio are needed for good agreement between experiments and simulations.

  7. A new high-throughput method utilizing porous silica-based nano-composites for the determination of partition coefficients of drug candidates.

    Science.gov (United States)

    Yu, Chih H; Tam, Kin; Tsang, Shik C

    2011-09-01

    We show that highly porous silica-based nanoparticles prepared via micro-emulsion and sol-gel techniques are stable colloids in aqueous solution. By incorporating a magnetic core into the porous silica nano-composite, it is found that the material can be rapidly separated (precipitated) upon exposure to an external magnetic field. Alternatively, the porous silica nanoparticles without magnetic cores can be equally separated from solution by applying a high-speed centrifugation. Using these silica-based nanostructures a new high-throughput method for the determination of partition coefficient for water/n-octanol is hereby described. First, a tiny quantity of n-octanol phase is pre-absorbed in the porous silica nano-composite colloids, which allows an establishment of interface at nano-scale between the adsorbed n-octanol with the bulk aqueous phase. Organic compounds added to the mixture can therefore undergo a rapid partition between the two phases. The concentration of drug compound in the supernatant in a small vial can be determined by UV-visible absorption spectroscopy. With the adaptation of a robotic liquid handler, a high-throughput technology for the determination of partition coefficients of drug candidates can be employed for drug screening in the industry based on these nano-separation skills. The experimental results clearly suggest that this new method can provide partition coefficient values of potential drug candidates comparable to the conventional shake-flask method but requires much shorter analytical time and lesser quantity of chemicals.

  8. Size-isolation of ultrasound-mediated phase change perfluorocarbon droplets using differential centrifugation.

    Science.gov (United States)

    Mercado, Karla P; Radhakrishnan, Kirthi; Stewart, Kyle; Snider, Lindsay; Ryan, Devin; Haworth, Kevin J

    2016-05-01

    Perfluorocarbon droplets that are capable of an ultrasound-mediated phase transition have applications in diagnostic and therapeutic ultrasound. Techniques to modify the droplet size distribution are of interest because of the size-dependent acoustic response of the droplets. Differential centrifugation has been used to isolate specific sizes of microbubbles. In this work, differential centrifugation was employed to isolate droplets with diameters between 1 and 3 μm and 2 and 5 μm from an initially polydisperse distribution. Further, an empirical model was developed for predicting the droplet size distribution following differential centrifugation and to facilitate the selection of centrifugation parameters for obtaining desired size distributions.

  9. Adiabatic field-free alignment of asymmetric top molecules with an optical centrifuge

    CERN Document Server

    Korobenko, A

    2015-01-01

    We use an optical centrifuge to align asymmetric top $\\mathrm{SO_2}$ molecules by adiabatically spinning their most polarizable O-O axis. The effective centrifugal potential in the rotating frame confines sulfur atoms to the plane of the laser-induced rotation, leading to the planar molecular alignment which persists after the molecules are released from the centrifuge. Periodic appearance of the full three-dimensional alignment, typically observed only with linear and symmetric top molecules, is also detected. Together with strong in-plane centrifugal forces, which bend the molecules by up to 10 degrees, permanent field-free alignment offers new ways of controlling molecules with laser light.

  10. High Order Centrifugal Distortion Corrections to Energy Levels of Asymmetric Top Molecules

    Institute of Scientific and Technical Information of China (English)

    LIU Yu-Yan; LIU Xiao-Yong; LIU Hong-Ping; GUO Yuan-Qing; HUANG Guang-Ming; LIN Jie-Li; GAO Hui

    2000-01-01

    High order centrifugal distortion terms have been derived and added to the effective Hamiltonian of asymmetric top molecules. Based on this Hamiltonian, a program in Fortran 77 has been developed for spectral analysis of asymmetric top molecules. The high order centrifugal distortion terms are found to be non-negligible even for the low-lying rotational transitions of molecules, such as Ha 18O, subjected to severe centrifugal distortion effect,and for the high-lying rotational transitions of molecules, such as 14N16O2 subjected to the moderate centrifugal distortion effect.

  11. Computer precision simulation for titanium casting centrifugal mold filling of prescision titanium castings

    Directory of Open Access Journals (Sweden)

    Daming XU

    2004-08-01

    Full Text Available Computer simulation codes were developed based on proposed mathematical model for centrifugal mold filling processes and previous computer software for 3D mold filling and solidification of castings. Sample simulations were implemented for mold filling processes of precision titanium castings under gravity and different centrifugal casting techniques. The computation results show that the alloy melt has a much stronger mold filling ability for thin section castings unde a centrifugal force field than that only under the gravity. A "return back" mold filling manner is showed to be a reasonable technique for centrifugal casting processes, especially for thin section prcision castings.

  12. Tutorial: simulating chromatography with Microsoft Excel Macros.

    Science.gov (United States)

    Kadjo, Akinde; Dasgupta, Purnendu K

    2013-04-22

    Chromatography is one of the cornerstones of modern analytical chemistry; developing an instinctive feeling for how chromatography works will be invaluable to future generation of chromatographers. Specialized software programs exist that handle and manipulate chromatographic data; there are also some that simulate chromatograms. However, the algorithm details of such software are not transparent to a beginner. In contrast, how spreadsheet tools like Microsoft Excel™ work is well understood and the software is nearly universally available. We show that the simple repetition of an equilibration process at each plate (a spreadsheet row) followed by discrete movement of the mobile phase down by a row, easily automated by a subroutine (a "Macro" in Excel), readily simulates chromatography. The process is readily understood by a novice. Not only does this permit simulation of isocratic and simple single step gradient elution, linear or multistep gradients are also easily simulated. The versatility of a transparent and easily understandable computational platform further enables the simulation of complex but commonly encountered chromatographic scenarios such as the effects of nonlinear isotherms, active sites, column overloading, on-column analyte degradation, etc. These are not as easily simulated by available software. Views of the separation as it develops on the column and as it is seen by an end-column detector are both available in real time. Excel 2010™ also permits a 16-level (4-bit) color gradation of numerical values in a column/row; this permits visualization of a band migrating down the column, much as Tswett may have originally observed, but in a numerical domain. All parameters of relevance (partition constants, elution conditions, etc.) are readily changed so their effects can be examined. Illustrative Excel spreadsheets are given in the Supporting Information; these are easily modified by the user or the user can write his/her own routine.

  13. LHCb: Optimising query execution time in LHCb Bookkeeping System using partition pruning and partition wise joins

    CERN Multimedia

    Mathe, Z

    2013-01-01

    The LHCb experiment produces a huge amount of data which has associated metadata such as run number, data taking condition (detector status when the data was taken), simulation condition, etc. The data are stored in files, replicated on the Computing Grid around the world. The LHCb Bookkeeping System provides methods for retrieving datasets based on their metadata. The metadata is stored in a hybrid database model, which is a mixture of Relational and Hierarchical database models and is based on the Oracle Relational Database Management System (RDBMS). The database access has to be reliable and fast. In order to achieve a high timing performance, the tables are partitioned and the queries are executed in parallel. When we store large amounts of data the partition pruning is essential for database performance, because it reduces the amount of data retrieved from the disk and optimises the resource utilisation. This research presented here is focusing on the extended composite partitioning strategy such as rang...

  14. A brief history of partitions of numbers, partition functions and their modern applications

    Science.gov (United States)

    Debnath, Lokenath

    2016-04-01

    'Number rules the universe.' The Pythagoras 'If you wish to forsee the future of mathematics our course is to study the history and present conditions of the science.' Henri Poincaré 'The primary source (Urqell) of all mathematics are integers.' Hermann Minkowski This paper is written to commemorate the centennial anniversary of the Mathematical Association of America. It deals with a short history of different kinds of natural numbers including triangular, square, pentagonal, hexagonal and k-gonal numbers, and their simple properties and their geometrical representations. Included are Euclid's and Pythagorean's main contributions to elementary number theory with the main contents of the Euclid Elements of the 13-volume masterpiece of mathematical work. This is followed by Euler's new discovery of the additive number theory based on partitions of numbers. Special attention is given to many examples, Euler's theorems on partitions of numbers with geometrical representations of Ferrers' graphs, Young's diagrams, Lagrange's four-square theorem and the celebrated Waring problem. Included are Euler's generating functions for the partitions of numbers, Euler's pentagonal number theorem, Gauss' triangular and square number theorems and the Jacobi triple product identity. Applications of the theory of partitions of numbers to different statistics such as the Bose- Einstein, Fermi- Dirac, Gentile, and Maxwell- Boltzmann statistics are briefly discussed. Special attention is given to pedagogical information through historical approach to number theory so that students and teachers at the school, college and university levels can become familiar with the basic concepts of partitions of numbers, partition functions and their modern applications, and can pursue advanced study and research in analytical and computational number theory.

  15. Design and Characterization of a Centrifugal Compressor Surge Test Rig

    Directory of Open Access Journals (Sweden)

    Kin Tien Lim

    2011-01-01

    Full Text Available A detailed description of a new centrifugal compressor surge test rig is presented. The objective of the design and development of the rig is to study the surge phenomenon in centrifugal compression systems and to investigate a novel method of surge control by active magnetic bearing servo actuation of the impeller axial tip clearance. In this paper, we focus on the design, initial setup, and testing of the rig. The latter two include the commissioning of the rig and the experimental characterization of the compressor performance. The behavior of the compressor during surge is analyzed by driving the experimental setup into surge. Two fundamental frequencies, 21 Hz and 7 Hz, connected to the surge oscillation in the test rig are identified, and the observed instability is categorized according to the intensity of pressure fluctuations. Based on the test results, the excited pressure waves are clearly the result of surge and not stall. Also, they exhibit the characteristics of mild and classic surge instead of deep surge. Finally, the change in the compressor performance due to variation in the impeller tip clearance is experimentally examined, and the results support the potential of the tip clearance modulation for the control of compressor surge. This is the first such demonstration of the feasibility of surge control of a compressor using active magnetic bearings.

  16. Flow in a Low Specific Speed Centrifugal Pump Using PIV

    Directory of Open Access Journals (Sweden)

    Cui Dai

    2013-01-01

    Full Text Available The interflow plays important roles in centrifugal pump design. In order to study the effect of rotation and z-axis on internal flow, two-dimensional particle image velocimetry (PIV measurements have been performed to measure the steady velocity field on three planes in all impeller passages of a low specific-speed centrifugal pump. The results show that the relative velocity flows in blade passages are obviously different in terms of the positions of the blade relative to the tongue. The interaction between the impeller and tongue changes the occurrence and development of low velocity region with time. From shroud to hub, the relative velocity gradually increases, and the minimum value moves toward the suction surface. On the midplane, the magnitude increases with increased flow rate from pressure surface to suction surface, while at the shroud and hub, the measured velocity first increases with decreased flow rate from the blade pressure surface to nearly ζ = 0.5 to 0.6.

  17. Centrifugal compression of soft particle packings: theory and experiment.

    Science.gov (United States)

    Nordstrom, K N; Verneuil, E; Ellenbroek, W G; Lubensky, T C; Gollub, J P; Durian, D J

    2010-10-01

    An exact method is developed for computing the height of an elastic medium subjected to centrifugal compression, for arbitrary constitutive relation between stress and strain. Example solutions are obtained for power-law media and for cases where the stress diverges at a critical strain--for example as required by packings composed of deformable but incompressible particles. Experimental data are presented for the centrifugal compression of thermo-responsive N-isopropylacrylamide (NIPA) microgel beads in water. For small radial acceleration, the results are consistent with Hertzian elasticity, and are analyzed in terms of the Young elastic modulus of the bead material. For large radial acceleration, the sample compression asymptotes to a value corresponding to a space-filling particle volume fraction of unity. Therefore we conclude that the gel beads are incompressible, and deform without deswelling. In addition, we find that the Young elastic modulus of the particulate gel material scales with cross-link density raised to the power 3.3±0.8, somewhat larger than the Flory expectation.

  18. In-vitro assessment of centrifugal pumps for ventricular assist.

    Science.gov (United States)

    Jakob, H; Kutschera, Y; Palzer, B; Prellwitz, W; Oelert, H

    1990-08-01

    Currently two major types of centrifugal pumps are commercially available for ventricular assist: the Biomedicus-cone (Group I) and the Centrimed-impeller pump (now Sarns 3M) (Group II). To compare them for blood trauma and hemolysis, an in-vitro experiment was designed with a Stöckert roller pump as a standard control (Group III). The in-vitro circuit was constructed consisting of a pump head, electromagnetic flow probe, polyvinyl chloride tubing and a reservoir, identical for all groups. Human ACD blood was used for priming and was circulated with a flow rate of 2 L/min for 24 h. Blood samples were taken at 0, 1, 3, 6, 12, and 24 h and zero control values were subtracted from the resulting data per time interval. Among the 16 parameters studied, a highly significant difference in favor of Group I was found for glutamate oxalacetate transaminase (GOT) and lactate dehydrogenase (p less than 0.0001) and for the free plasma hemoglobin (p less than 0.0001) after 12 and 24 h, respectively. The hemolytic index (Allen) again was lowest for group I in contrast to Groups II and III (0.012 versus 0.060 and 1.70) after 24 h. All other parameters studied did not render significant differences between the systems tested. The authors conclude that the Biomedicus pump currently is the least traumatic centrifugal pump for ventricular assist.

  19. Platelet function and hemolysis in centrifugal pumps: in vitro investigations.

    Science.gov (United States)

    Steines, D; Westphal, D; Göbel, C; Reul, H; Rau, G

    1999-08-01

    The effects of centrifugal pumps on blood components other than erythrocytes, namely platelets and their interaction with the coagulation system, are not very well known. In a comparative study with three centrifugal pumps (BioMedicus BP-80, St. Jude Isoflow, and Sarns Delphin) and the Stockert roller pump hemolysis, platelet counts, thromboplastin and partial thromboplastin times, as well as resonance thrombography (RTG) parameters for the assessment of platelet and coagulation function were evaluated in vitro. Normalized indices of hemolysis (NIH) with ACD anticoagulation after 360 minutes were 0.008+/-0.004 (Isoflow), 0.018+/-0.017 (BP-80), 0.085+/-0.051 (Delphin), and 0.049+/-0.010 g/1001 (roller pump). Plasmatic coagulation was activated in all circuits. Platelet function was severely inhibited by the BP-80, indicated by increase in RTG platelet time to 358%+/-150% of initial values compared to 42%+/-29% (Isoflow), 40%+/-20% (Delphin), and 12%+/-10% (roller pump). Fibrin polymerization was affected similarly. The large surface area of the BP-80 leads to an extensive activation of platelets and plasminogen.

  20. Numerical Study of Unsteady Flow in Centrifugal Cold Compressor

    Science.gov (United States)

    Zhang, Ning; Zhang, Peng; Wu, Jihao; Li, Qing

    In helium refrigeration system, high-speed centrifugal cold compressor is utilized to pumped gaseous helium from saturated liquid helium tank at low temperature and low pressure for producing superfluid helium or sub-cooled helium. Stall and surge are common unsteady flow phenomena in centrifugal cold compressors which severely limit operation range and impact efficiency reliability. In order to obtain the installed range of cold compressor, unsteady flow in the case of low mass flow or high pressure ratio is investigated by the CFD. From the results of the numerical analysis, it can be deduced that the pressure ratio increases with the decrease in reduced mass flow. With the decrease of the reduced mass flow, backflow and vortex are intensified near the shroud of impeller. The unsteady flow will not only increase the flow loss, but also damage the compressor. It provided a numerical foundation of analyzing the effect of unsteady flow field and reducing the flow loss, and it is helpful for the further study and able to instruct the designing.

  1. Experiments on Plasma Injection into a Centrifugally Confined System

    Science.gov (United States)

    Messer, S.; Bomgardner, R.; Brockington, S.; Case, A.; Witherspoon, F. D.; Uzun-Kaymak, I.; Elton, R.; Young, W.; Teodorescu, C.; Morales, C. H.; Ellis, R. F.

    2009-11-01

    We describe the cross-field injection of plasma into a centrifugally-confined system. Two different types of plasma railgun have been installed on the Maryland Centrifugal Experiment (MCX) in an attempt to drive that plasma's rotation. The initial gun was a coaxial device designed to mitigate the blowby instability. The second one was a MiniRailgun with a rectangular bore oriented so that the MCX magnetic field augments the railgun's internal magnetic field. Tests at HyperV indicate this MiniRailgun reaches much higher densities than the original gun, although muzzle velocity is slightly reduced. We discuss the impact of these guns on MCX for various conditions. Initial results show that even for a 2 kG field, firing the MiniRailgun modifies oscillations of the MCX diamagnetic loops and can impact the core current and voltage. The gun also has a noticeable impact on MCX microwave emissions. These observations suggest plasma enters the MCX system. We also compare diagnostic data collected separately from MCX for these and other guns, focussing primarily on magnetic measurements.

  2. LISSAT Analysis of a Generic Centrifuge Enrichment Plant

    Energy Technology Data Exchange (ETDEWEB)

    Lambert, H; Elayat, H A; O?Connell, W J; Szytel, L; Dreicer, M

    2007-05-31

    The U.S. Department of Energy (DOE) is interested in developing tools and methods for use in designing and evaluating safeguards systems for current and future plants in the nuclear power fuel cycle. The DOE is engaging several DOE National Laboratories in efforts applied to safeguards for chemical conversion plants and gaseous centrifuge enrichment plants. As part of the development, Lawrence Livermore National Laboratory has developed an integrated safeguards system analysis tool (LISSAT). This tool provides modeling and analysis of facility and safeguards operations, generation of diversion paths, and evaluation of safeguards system effectiveness. The constituent elements of diversion scenarios, including material extraction and concealment measures, are structured using directed graphs (digraphs) and fault trees. Statistical analysis evaluates the effectiveness of measurement verification plans and randomly timed inspections. Time domain simulations analyze significant scenarios, especially those involving alternate time ordering of events or issues of timeliness. Such simulations can provide additional information to the fault tree analysis and can help identify the range of normal operations and, by extension, identify additional plant operational signatures of diversions. LISSAT analyses can be used to compare the diversion-detection probabilities for individual safeguards technologies and to inform overall strategy implementations for present and future plants. Additionally, LISSAT can be the basis for a rigorous cost-effectiveness analysis of safeguards and design options. This paper will describe the results of a LISSAT analysis of a generic centrifuge enrichment plant. The paper will describe the diversion scenarios analyzed and the effectiveness of various safeguards systems alternatives.

  3. Numerical modeling of centrifuge cyclic lateral pile load experiments

    Institute of Scientific and Technical Information of China (English)

    Nikos Gerolymos; Sandra Escoffer; George Gazetas; Jacques Gamier

    2009-01-01

    To gain insight into the inelastic behavior of piles, the response of a vertical pile embedded in dry sand and subjected to cyclic lateral loading was studied experimentally in centrifuge tests conducted in Laboratoire Central des Ponts et Chaussees. Three types of cyclic loading were applied, two asymmetric and one symmetric with respect to the unloaded pile. An approximately square-root variation of soil stiffness with depth was obtained from indirect in-flight density measurements, laboratory tests on reconstituted samples, and well-established empirical correlations. The tests were simulated using a cyclic nonlinear Winkler spring model, which describes the full range of inelastic phenomena, including separation and re-attachment of the pile from and to the soil. The model consists of three mathematical expressions capable of reproducing a wide variety of monotonic and cyclic experimental p-y curves. The physical meaning of key model parameters is graphically explained and related to soil behavior. Comparisons with the centrifuge test results demonstrate the general validity of the model and its ability to capture several features of pile-soil interaction, including: soil plastification at an early stage of loading, "pinching" behavior due to the formation of a relaxation zone around the upper part of the pile, and stiffness and strength changes due to cyclic loading. A comparison of the p-y curves derived from the test results and the proposed model, as well as those from the classical curves of Reese et al. (1974) for sand, is also presented.

  4. Radio-metabolite analysis of carbon-11 biochemical partitioning to non-structural carbohydrates for integrated metabolism and transport studies.

    Science.gov (United States)

    Babst, Benjamin A; Karve, Abhijit A; Judt, Tatjana

    2013-06-01

    Metabolism and phloem transport of carbohydrates are interactive processes, yet each is often studied in isolation from the other. Carbon-11 ((11)C) has been successfully used to study transport and allocation processes dynamically over time. There is a need for techniques to determine metabolic partitioning of newly fixed carbon that are compatible with existing non-invasive (11)C-based methodologies for the study of phloem transport. In this report, we present methods using (11)C-labeled CO2 to trace carbon partitioning to the major non-structural carbohydrates in leaves-sucrose, glucose, fructose and starch. High-performance thin-layer chromatography (HPTLC) was adapted to provide multisample throughput, raising the possibility of measuring different tissues of the same individual plant, or for screening multiple plants. An additional advantage of HPTLC was that phosphor plate imaging of radioactivity had a much higher sensitivity and broader range of sensitivity than radio-HPLC detection, allowing measurement of (11)C partitioning to starch, which was previously not possible. Because of the high specific activity of (11)C and high sensitivity of detection, our method may have additional applications in the study of rapid metabolic responses to environmental changes that occur on a time scale of minutes. The use of this method in tandem with other (11)C assays for transport dynamics and whole-plant partitioning makes a powerful combination of tools to study carbohydrate metabolism and whole-plant transport as integrated processes.

  5. Cardio-postural interactions and short-arm centrifugation.

    Science.gov (United States)

    Blaber, Andrew; Goswami, Nandu; Xu, Da; Laurin, Alexendre

    INTRODUCTION: We are interested in mechanisms associated with orthostatic tolerance. In previous studies we have shown that postural muscles in the calf contribute to both posture and blood pressure regulation during orthostatic stress. In this study we investigated the relationship between cardiovascular and postural muscle control before, during and after short arm human centrifuge (SAHC) up to 2.2 G. METHODS: Eleven healthy young subjects (6 m, 5 f), with no history of cardiovascular disease, falls or orthostatic hypotension, participated. All were familiarized with the SAHC with 10 minutes at 1-G at the feet. Each subject was instrumented in the supine position on the SAHC for beat-to-beat ECG and blood pressure (Portapres derived SBP). Bilateral lower leg EMG was collected from four leg postural muscles: tibialis anterior, medial gastrocnemius, lateral gastrocnemius, and medial soleus. Transdermal differential recording of signals was performed using an 8-channel EMG system, (Myosystem 1200, Noraxon Inc., Arizona, USA). Postural sway data of the body COP was computed from the force and moment data collected with a force platform (Accusway, AMTI, MA, USA). Before and after SAHC, the subject stood on a force platform with their gaze fixed on a point at eye level, closed their eyes and stood quietly for 5 min. A final stand was conducted 30 min after centrifugation with supine rest in between. During clockwise centrifugation (10-min 1g and 10-min 2.2g at the foot) the subjects’ head was hooded and in the dark. The subject’s body was restrained into the rotation arm with a parachute harness and given additional body support with a foot-plate. ECG, EMG and BP data were collected throughout and centre of pressure trajectory (COP) collected during the stand test. Subjects were requested to relax and not to voluntarily contract the leg muscles; however, they were not to suppress contractions as they occurred involuntarily or by reflex. A Continuous Wavelet

  6. Micellar Electrokinetic Chromatography

    Science.gov (United States)

    Bald, Edward; Kubalczyk, Paweł

    Since the introduction of micellar electrokinetic chromatography by Terabe, several authors have paid attention to the fundamental characteristics of this separation method. In this chapter the theoretical and practical aspects of resolution optimization, as well as the effect of different separation parameters on the migration behavior are discussed. These among others include fundamentals of separation, retention factor and resolution equation, efficiency, selectivity, and various surfactants and additives. Initial conditions for method development and instrumental approaches such as mass spectrometry detection are also mentioned covering the proposals for overcoming the difficulties arising from the coupling micellar electrokinetic chromatography with mass spectrometry detection.

  7. Micellar liquid chromatography

    Science.gov (United States)

    Basova, Elena M.; Ivanov, Vadim M.; Shpigun, Oleg A.

    1999-12-01

    Background and possibilities of practical applications of micellar liquid chromatography (MLC) are considered. Various retention models in MLC, the effects of the nature and concentration of surfactants and organic modifiers, pH, temperature and ionic strength on the MLC efficiency and selectivity are discussed. The advantages and limitations of MLC are demonstrated. The performance of MLC is critically evaluated in relationship to the reversed-phase HPLC and ion-pair chromatography. The potential of application of MLC for the analysis of pharmaceuticals including that in biological fluids and separation of inorganic anions, transition metal cations, metal chelates and heteropoly compounds is described. The bibliography includes 146 references.

  8. Size fractionation by slalom chromatography and hydrodynamic chromatography

    OpenAIRE

    Dias, Ricardo P.

    2008-01-01

    Hydrodynamic chromatography, also called separation by flow, is based on the use of the parabolic flow profile occurring in open capillaries or in the pores from a column filled with non-porous particles. The hydrodynamic chromatography separation medium, if any, is much simpler than that from size exclusion chromatography (porous particles), the former technique being used in the size-fractionation of many colloids and macromolecules. The transition between hydrodynamic chromatography (obtai...

  9. Knowledge base rule partitioning design for CLIPS

    Science.gov (United States)

    Mainardi, Joseph D.; Szatkowski, G. P.

    1990-01-01

    This describes a knowledge base (KB) partitioning approach to solve the problem of real-time performance using the CLIPS AI shell when containing large numbers of rules and facts. This work is funded under the joint USAF/NASA Advanced Launch System (ALS) Program as applied research in expert systems to perform vehicle checkout for real-time controller and diagnostic monitoring tasks. The Expert System advanced development project (ADP-2302) main objective is to provide robust systems responding to new data frames of 0.1 to 1.0 second intervals. The intelligent system control must be performed within the specified real-time window, in order to meet the demands of the given application. Partitioning the KB reduces the complexity of the inferencing Rete net at any given time. This reduced complexity improves performance but without undo impacts during load and unload cycles. The second objective is to produce highly reliable intelligent systems. This requires simple and automated approaches to the KB verification & validation task. Partitioning the KB reduces rule interaction complexity overall. Reduced interaction simplifies the V&V testing necessary by focusing attention only on individual areas of interest. Many systems require a robustness that involves a large number of rules, most of which are mutually exclusive under different phases or conditions. The ideal solution is to control the knowledge base by loading rules that directly apply for that condition, while stripping out all rules and facts that are not used during that cycle. The practical approach is to cluster rules and facts into associated 'blocks'. A simple approach has been designed to control the addition and deletion of 'blocks' of rules and facts, while allowing real-time operations to run freely. Timing tests for real-time performance for specific machines under R/T operating systems have not been completed but are planned as part of the analysis process to validate the design.

  10. UNIFIED THEORETICAL MOMENT EXPRESSIONS FOR ELUTION CHROMATOGRAPHY AND FRONTAL CHROMATOGRAPHY

    Institute of Scientific and Technical Information of China (English)

    YANGGengliang; TAOZuyi

    1992-01-01

    The unified theoretical moment expressions for elution chromatography and frontal chromatography when the sorption process is described by a linear model were derived. The moment expressions derived by previous authors can be obtained from these unified theoretical moment expressions. In this paper, a mathematical analysis has been carried out so as to set up a unified theoretical basis for elution and frontal chromatography.

  11. Surface defects and instanton partition functions

    Science.gov (United States)

    Gaiotto, Davide; Kim, Hee-Cheol

    2016-10-01

    We study the superconformal index of five-dimensional SCFTs and the sphere partition function of four-dimensional gauge theories with eight supercharges in the presence of co-dimension two half-BPS defects. We derive a prescription which is valid for defects which can be given a "vortex construction", i.e. can be defined by RG flow from vortex configurations in a larger theory. We test the prescription against known results and expected dualities. We employ our prescription to develop a general computational strategy for defects defined by coupling the bulk degrees of freedom to a Gauged Linear Sigma Model living in co-dimension two.

  12. Zero-sum partition theorems for graphs

    Directory of Open Access Journals (Sweden)

    Y. Caro

    1994-01-01

    Full Text Available Let q=pn be a power of an odd prime p. We show that the vertices of every graph G can be partitioned into t(q classes V(G=⋃t=1t(qVi such that the number of edges in any induced subgraph 〈Vi〉 is divisible by q, where t(q≤32(q−1−(2(q−1−1124+98, and if q=2n, then t(q=2q−1.

  13. Incidence of electrocardiographic changes during cytapheresis using an intermittent flow centrifuge, haemonetics V50 and a continuous flow centrifuge, AS104.

    Science.gov (United States)

    Komatsu, F; Kajiwara, M

    1997-03-01

    Electrocardiographic (ECG) monitoring was performed during cytapheresis and the incidence of ECG changes was compared between methods of intermittent flow centrifugation using the Haemonetics V50 with apheresis donors and continuous flow centrifugation with the AS104 for peripheral blood stem cell (PBSC) collection from patients. ST depression, inverted T wave and other ECG changes were found in 49 (14.3%) of the 342 cytaphereses carried out by the intermittent flow centrifugation method and in 8 (4.7%) of the 169 PBSC collections by the continuous flow centrifugation method. This difference was significant (P < 0.05). The hemodynamic changes in the procedure with the AS104 seem to be small. This is considered to be important for prevention of serious ST and T wave changes.

  14. Design and development of single stage purification of papain using Ionic Liquid based aqueous two phase extraction system and its Partition coefficient studies

    Directory of Open Access Journals (Sweden)

    Senthilkumar Rathnasamy

    2013-04-01

    Full Text Available As an emerging trend in bioseparation, aqueous two phase extractions based on phosponium ionic liquid have been utilized in this work to extract papain from Carica papaya fruit latex and the same wascompared with conventional aqueous two phase extraction system. Factors affecting the partition coefficient of papain such as ionic liquid concentration, pH of the extraction system and temperature have been investigated. The optimization studies show that ionic liquid concentrations and pH are majorly influencing the phaseformations and papain partitioning. It reveals the importance of electrostatic and hydrophobic interactions in the papain partitioning. Purification studies performed on Gel Filtration Chromatography shows that 96% of the papain enzyme could be extracted with the phosponium based ionic liquid in a single stage extraction. The final fraction containing papain enzyme was confirmed by SDS Page analysis.

  15. Modern Thin-Layer Chromatography.

    Science.gov (United States)

    Poole, Colin F.; Poole, Salwa K.

    1989-01-01

    Some of the important modern developments of thin-layer chromatography are introduced. Discussed are the theory and instrumentation of thin-layer chromatography including multidimensional and multimodal techniques. Lists 53 references. (CW)

  16. Partition Equilibrium Between Charged Membrane and Single Electrolyte Aqueous Solution

    Institute of Scientific and Technical Information of China (English)

    徐铜文; 杨伟华; 何柄林

    2001-01-01

    Ionic partition equilibrium in charged membrane immersed in solution of single electrolyte with monovalence or multi-valence is systematically investigated and several expressions are established for determination of partition coefficients. On this basis, the effects of the ratio of membrane charge density to hulk electrolyte solution concentration, the charge sign and valence of electrolyte ions and the type of membrane on the partition equilibrium were analyzed and simulated with in chosen parameters. It is revealed that ion partition is not related solely withthe respective concentrations but also definitely with the concentration ratio of fixed group to bulk solution in addition to the charge sign and the valence. For a counterion, the partition coefficient increases with this ratio and the valence; while for a coion, the partition coefficient decreases with this ratio and the valence. The theoreticalcal culations were compared with the experimental data and a good agreement was observed.

  17. Partition Equilibrium Between Charged Membrane and Single Electrolyte Aqueous Solution

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Ionic partition equilibrium in charged membrane immersed in solution of single electrolyte with mono valence or multi-valence is systematically investigated and several expressions are established for determination of partition coefficients. On this basis, the effects of the ratio of membrane charge density to bulk electrolyte solution concentration, the charge sign and valence of electrolyte ions and the type of membrane on the partition equilibrium were analyzed and simulated within chosen parameters. It is revealed that ion partition is not related solely with the respective concentrations but also definitely with the concentration ratio of fixed group to bulk solution in addition to the charge sign and the valence. For a counterion, the partition coefficient increases with this ratio and the valence; while for a coion, the partition coefficient decreases with this ratio and the valence. The theoretical calculations were compared with the experimental data and a good agreement was observed.

  18. Modular properties of full 5D SYM partition function

    CERN Document Server

    Qiu, Jian; Winding, Jacob; Zabzine, Maxim

    2015-01-01

    We study properties of the full partition function for the $U(1)$ 5D $\\mathcal{N}=2^*$ gauge theory with adjoint hypermultiplet of mass $M$. This theory is ultimately related to abelian 6D (2,0) theory. We construct the full non-perturbative partition function on toric Sasaki-Einstein manifolds by gluing flat copies of the Nekrasov partition function and we express the full partition function in terms of the generalized double elliptic gamma function $G_2^C$ associated with a certain moment map cone $C$. The answer exhibits a curious $SL(4,\\mathbb{Z})$ modular property. Finally, we propose a set of rules to construct the partition function that resembles the calculation of 5D supersymmetric partition function with the insertion of defects of various co-dimensions.

  19. Modular properties of full 5D SYM partition function

    Science.gov (United States)

    Qiu, Jian; Tizzano, Luigi; Winding, Jacob; Zabzine, Maxim

    2016-03-01

    We study properties of the full partition function for the U(1) 5D N = {2}^{ast } gauge theory with adjoint hypermultiplet of mass M . This theory is ultimately related to abelian 6D (2,0) theory. We construct the full non-perturbative partition function on toric Sasaki-Einstein manifolds by gluing flat copies of the Nekrasov partition function and we express the full partition function in terms of the generalized double elliptic gamma function G 2 C associated with a certain moment map cone C. The answer exhibits a curious SL(4 , ℤ) modular property. Finally, we propose a set of rules to construct the partition function that resembles the calculation of 5d supersymmetric partition function with the insert ion of defects of various co-dimensions.

  20. Extending Paper Chromatography Inquiry

    Science.gov (United States)

    Finson, Kevin

    2004-01-01

    One of the "good old" standard activities middle school students seem to enjoy is paper chromatography. The procedures and materials needed are relatively simple and the results can be colorful. All too often, the activity ends just after these colorful results are obtained, cutting short the potential it holds for some further inquiry. With some…

  1. Chromatography in industry

    NARCIS (Netherlands)

    Schoenmakers, P.

    2009-01-01

    This review focuses on the chromatography research that has been carried out within industry or in close cooperation with industry and that has been reported in the scientific literature between 2006 and mid-2008. Companies in the health care sector, such as pharmaceutical and biotechnology companie

  2. CLASSIFICATION OF COMPLETE 5-PARTITE GRAPHS AND CHROMATICITY OF 5-PARTITE GRAPHSWITH 5n VERTICES

    Institute of Scientific and Technical Information of China (English)

    ZhaoHaixing; LiuRuying; ZhangShenggui

    2004-01-01

    For a graph G,P(G,λ)denotes the chromatic polynomial of G. Two graphs G and H are said to be chromatically equivalent,denoted by G-H,if P(G,λ)=p(H,λ). Let[G]= {H|H-G}. If [G]={G},then G is said to be chromatically unique. For a complete 5-partite graph G with 5n vertices, define θ(G)=(a(G,6)-2n+1-2n-1+5)/2n-2,where a(G,6) denotes the number of 6-independent partitions of G. In this paper, the authors show that θ(G)≥0 and determine all graphs with θ(G)= 0, 1, 2, 5/2, 7/2, 4, 17/4. By using these results the chromaticity of 5-partite graphs of the form G-S with θ(G)=0,1,2,5/2,7/2,4,17/4 is investigated,where S is a set of edges of G. Many new chromatically unique 5-partite graphs are obtained.

  3. Centripetal/Centrifugal Family Style of Families with Aggressive and Non-Aggressive Boys.

    Science.gov (United States)

    Hurst, Duane F.; And Others

    Research on family interaction has characterized family style on centripetal and centrifugal dimensions, representing opposing natures with their own continua. Centripetal forces produce binding, or a prolonged process of separation of parent and child; centrifugal forces preciptate expelling, or hastened separation and premature autonomy. To…

  4. Numerical Calculation of the Three-Dimensional Swirling Flow Inside the Centrifugal Pump Volutes

    Directory of Open Access Journals (Sweden)

    E. Cezmi Nursen

    2003-01-01

    Full Text Available The flow inside the volute of a centrifugal pump is threedimensional and, depending upon the position of the inlet relative to the cross-section center line, a single or double swirling flow occurs. The purpose of this study was the calculation of the three-dimensional swirling flow inside the centrifugal pump volute.

  5. PECULIARITIES OF STRUCTURE-FORMATION AT SVS IN MELTED CONDENSED MIXTURES AT INFLUENCE OF CENTRIFUGAL FORCE

    Directory of Open Access Journals (Sweden)

    V. V. Hubovich

    2007-01-01

    Full Text Available The influence of centrifugal force on dynamics of the burning wave spread and the carbide particles distribution in metallic alloy in the process of SVS-casting is considered. It was concluded that centrifugal force can be used for production of materials with gradient of the hardening particles concentration.

  6. The theory of the centrifugal mechanism of feeding-in in bent crystals

    OpenAIRE

    2001-01-01

    For a particle channeled in the bent crystal planes (axes), the phenomenon of "bending dechanneling", which is a particle transition to a random state due to centrifugal force, is well known. We consider an analytical theory of the reverse phenomenon, i.e., feeding from a random state to a channeled state due to centrifugal force in a crystal with variable curvature.

  7. Peak capacity in unidimensional chromatography.

    Science.gov (United States)

    Neue, Uwe Dieter

    2008-03-14

    The currently existing knowledge about peak capacity in unidimensional separations is reviewed. The majority of the paper is dedicated to reversed-phase gradient chromatography, covering specific techniques as well as the subject of peak compression. Other sections deal with peak capacity in isocratic chromatography, size-exclusion chromatography and ion-exchange chromatography. An important topic is the limitation of the separation power and the meaning of the concept of peak capacity for real applications.

  8. Application of genetic algorithm-kernel partial least square as a novel non-linear feature selection method: partitioning of drug molecules.

    Science.gov (United States)

    Noorizadeh, H; Sobhan Ardakani, S; Ahmadi, T; Mortazavi, S S; Noorizadeh, M

    2013-02-01

    Genetic algorithm (GA) and partial least squares (PLS) and kernel PLS (KPLS) techniques were used to investigate the correlation between immobilized liposome chromatography partitioning (log Ks) and descriptors for 65 drug compounds. The models were validated using leave-group-out cross validation LGO-CV. The results indicate that GA-KPLS can be used as an alternative modelling tool for quantitative structure-property relationship (QSPR) studies.

  9. Concept designs of nonrotating-type centrifugal blood pump and basic study on output characteristics of the oscillating disk-type centrifugal pump.

    Science.gov (United States)

    Kabei, N; Tuichiya, K; Sakurai, Y

    1994-09-01

    When designing a turbo-type blood pump as an artificial heart, the gap between a rotating shaft and a pump housing should be perfectly sealed to prevent any leakage or contamination through a seal. In addition, blood coagulation in a blood chamber must be avoided. To overcome these problems, we proposed five different nonrotating-type turbo pumps: a caudal-fin-type axial-flow pump, a caudal-fin-type centrifugal pump, a nutating-column-type centrifugal pump, a nutating-collapsible-tube-type centrifugal pump, and an oscillating-disk-type centrifugal pump. We selected and developed the oscillating-disk-type centrifugal pump that consists of a disk, a driving rod, a seal, an oscillation mechanism, and a pump housing. The disk is mounted on the end of the rod, which is connected to a high-speed DC motor through an oscillation mechanism. The rod and the disk do not rotate, but they oscillate in the pump housing. This movement of the disk generates forward fluid flow around the axis (i.e., the rotational fluid flow). Centrifugal force due to fluid rotation supports the pressure difference between the outlet and the inlet. The diameter of the disk is 39 mm, the maximum inner diameter of the pump housing is 40 mm, and the volume of the blood chamber for 25 degrees' oscillation is 16.9 ml. The performance of the pump was tested in a mock circulatory system.(ABSTRACT TRUNCATED AT 250 WORDS)

  10. High Technology Centrifugal Compressor for Commercial Air Conditioning Systems

    Energy Technology Data Exchange (ETDEWEB)

    Ruckes, John

    2006-04-15

    R&D Dynamics, Bloomfield, CT in partnership with the State of Connecticut has been developing a high technology, oil-free, energy-efficient centrifugal compressor called CENVA for commercial air conditioning systems under a program funded by the US Department of Energy. The CENVA compressor applies the foil bearing technology used in all modern aircraft, civil and military, air conditioning systems. The CENVA compressor will enhance the efficiency of water and air cooled chillers, packaged roof top units, and other air conditioning systems by providing an 18% reduction in energy consumption in the unit capacity range of 25 to 350 tons of refrigeration The technical approach for CENVA involved the design and development of a high-speed, oil-free foil gas bearing-supported two-stage centrifugal compressor, CENVA encompassed the following high technologies, which are not currently utilized in commercial air conditioning systems: Foil gas bearings operating in HFC-134a; Efficient centrifugal impellers and diffusers; High speed motors and drives; and System integration of above technologies. Extensive design, development and testing efforts were carried out. Significant accomplishments achieved under this program are: (1) A total of 26 builds and over 200 tests were successfully completed with successively improved designs; (2) Use of foil gas bearings in refrigerant R134a was successfully proven; (3) A high speed, high power permanent magnet motor was developed; (4) An encoder was used for signal feedback between motor and controller. Due to temperature limitations of the encoder, the compressor could not operate at higher speed and in turn at higher pressure. In order to alleviate this problem a unique sensorless controller was developed; (5) This controller has successfully been tested as stand alone; however, it has not yet been integrated and tested as a system; (6) The compressor successfully operated at water cooled condensing temperatures Due to temperature

  11. THE ALGORITHMS OF AN INTEGER PARTITIONING WITH ITS APPLICATIONS

    Institute of Scientific and Technical Information of China (English)

    曹立明; 周强

    1994-01-01

    In the light of the ideals of Artificial Intelligence(AI) , three algorithms of an integer partitioning have been given in this paper:generate and test algorithm ,and two heuristic algorithms about forward partition and backward partition. PROLOG has been used to describe algorithms, it is reasonable, direct and simple. In the sight of describing algorithms ,it is a new and valid try. At last, some intresting applications of the algorithms mentioned in the paper have been presented.

  12. Partition function of nearest neighbour Ising models: Some new insights

    Indian Academy of Sciences (India)

    G Nandhini; M V Sangaranarayanan

    2009-09-01

    The partition function for one-dimensional nearest neighbour Ising models is estimated by summing all the energy terms in the Hamiltonian for N sites. The algebraic expression for the partition function is then employed to deduce the eigenvalues of the basic 2 × 2 matrix and the corresponding Hermitian Toeplitz matrix is derived using the Discrete Fourier Transform. A new recurrence relation pertaining to the partition function for two-dimensional Ising models in zero magnetic field is also proposed.

  13. Partitioning and lipophilicity in quantitative structure-activity relationships.

    OpenAIRE

    Dearden, J. C.

    1985-01-01

    The history of the relationship of biological activity to partition coefficient and related properties is briefly reviewed. The dominance of partition coefficient in quantitation of structure-activity relationships is emphasized, although the importance of other factors is also demonstrated. Various mathematical models of in vivo transport and binding are discussed; most of these involve partitioning as the primary mechanism of transport. The models describe observed quantitative structure-ac...

  14. Method for chemical amplification based on fluid partitioning in an immiscible liquid

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, Brian L.; Colston, Bill W.; Elkin, Christopher J.

    2017-02-28

    A system for nucleic acid amplification of a sample comprises partitioning the sample into partitioned sections and performing PCR on the partitioned sections of the sample. Another embodiment of the invention provides a system for nucleic acid amplification and detection of a sample comprising partitioning the sample into partitioned sections, performing PCR on the partitioned sections of the sample, and detecting and analyzing the partitioned sections of the sample.

  15. High Performance Thin Layer Chromatography.

    Science.gov (United States)

    Costanzo, Samuel J.

    1984-01-01

    Clarifies where in the scheme of modern chromatography high performance thin layer chromatography (TLC) fits and why in some situations it is a viable alternative to gas and high performance liquid chromatography. New TLC plates, sample applications, plate development, and instrumental techniques are considered. (JN)

  16. Partitioning kinetic energy during freewheeling wheelchair maneuvers.

    Science.gov (United States)

    Medola, Fausto O; Dao, Phuc V; Caspall, Jayme J; Sprigle, Stephen

    2014-03-01

    This paper describes a systematic method to partition the kinetic energy (KE) of a free-wheeling wheelchair. An ultralightweight rigid frame wheelchair was instrumented with two axle-mounted encoders and data acquisition equipment to accurately measure the velocity of the drive wheels. A mathematical model was created combining physical specifications and geometry of the wheelchair and its components. Two able-bodied subjects propelled the wheelchair over four courses that involved straight and turning maneuvers at differing speeds. The KE of the wheelchair was divided into three components: translational, rotational, and turning energy. This technique was sensitive to the changing contributions of the three energy components across maneuvers. Translational energy represented the major component of total KE in all maneuvers except a zero radius turn in which turning energy was dominant. Both translational and rotational energies are directly related to wheelchair speed. Partitioning KE offers a useful means of investigating the dynamics of a moving wheelchair. The described technique permits analysis of KE imparted to the wheelchair during maneuvers involving changes in speed and direction, which are most representative of mobility in everyday life. This technique can be used to study the effort required to maneuver different types and configurations of wheelchairs.

  17. Gait Partitioning Methods: A Systematic Review

    Science.gov (United States)

    Taborri, Juri; Palermo, Eduardo; Rossi, Stefano; Cappa, Paolo

    2016-01-01

    In the last years, gait phase partitioning has come to be a challenging research topic due to its impact on several applications related to gait technologies. A variety of sensors can be used to feed algorithms for gait phase partitioning, mainly classifiable as wearable or non-wearable. Among wearable sensors, footswitches or foot pressure insoles are generally considered as the gold standard; however, to overcome some inherent limitations of the former, inertial measurement units have become popular in recent decades. Valuable results have been achieved also though electromyography, electroneurography, and ultrasonic sensors. Non-wearable sensors, such as opto-electronic systems along with force platforms, remain the most accurate system to perform gait analysis in an indoor environment. In the present paper we identify, select, and categorize the available methodologies for gait phase detection, analyzing advantages and disadvantages of each solution. Finally, we comparatively examine the obtainable gait phase granularities, the usable computational methodologies and the optimal sensor placements on the targeted body segments. PMID:26751449

  18. Inversion of hematocrit partition at microfluidic bifurcations.

    Science.gov (United States)

    Shen, Zaiyi; Coupier, Gwennou; Kaoui, Badr; Polack, Benoît; Harting, Jens; Misbah, Chaouqi; Podgorski, Thomas

    2016-05-01

    Partitioning of red blood cells (RBCs) at the level of bifurcations in the microcirculatory system affects many physiological functions yet it remains poorly understood. We address this problem by using T-shaped microfluidic bifurcations as a model. Our computer simulations and in vitro experiments reveal that the hematocrit (ϕ0) partition depends strongly on RBC deformability, as long as ϕ0<20% (within the normal range in microcirculation), and can even lead to complete deprivation of RBCs in a child branch. Furthermore, we discover a deviation from the Zweifach-Fung effect which states that the child branch with lower flow rate recruits less RBCs than the higher flow rate child branch. At small enough ϕ0, we get the inverse scenario, and the hematocrit in the lower flow rate child branch is even higher than in the parent vessel. We explain this result by an intricate up-stream RBC organization and we highlight the extreme dependence of RBC transport on geometrical and cell mechanical properties. These parameters can lead to unexpected behaviors with consequences on the microcirculatory function and oxygen delivery in healthy and pathological conditions.

  19. Ferrous iron partitioning in the lower mantle

    Science.gov (United States)

    Muir, Joshua M. R.; Brodholt, John P.

    2016-08-01

    We used density functional theory (DFT) to examine the partitioning of ferrous iron between periclase and bridgmanite under lower mantle conditions. To study the effects of the three major variables - pressure, temperature and concentration - these have been varied from 0 to 150 GPa, from 1000 to 4000 K and from 0 to 100% total iron content. We find that increasing temperature increases KD, increasing iron concentration decreases KD, while pressure can both increase and decrease KD. We find that KD decreases slowly from about 0.32 to 0.06 with depth under lower mantle conditions. We also find that KD increases sharply to 0.15 in the very lowermost mantle due to the strong temperature increases near the CMB. Spin transitions have a large effect on the activity of ferropericlase which causes KD to vary with pressure in a peak-like fashion. Despite the apparently large changes in KD through the mantle, this actually results in relatively small changes in total iron content in the two phases, with XFefp ranging from about 0.20 to 0.35, before decreasing again to about 0.28 at the CMB, and XFebd has a pretty constant value of about 0.04-0.07 throughout the lower mantle. For the very high Fe concentrations suggested for ULVZs, Fe partitions very strongly into ferropericlase.

  20. Strictly nonnegative tensors and nonnegative tensor partition

    Institute of Scientific and Technical Information of China (English)

    HU ShengLong; HUANG ZhengHai; QI LiQun

    2014-01-01

    We introduce a new class of nonnegative tensors—strictly nonnegative tensors.A weakly irreducible nonnegative tensor is a strictly nonnegative tensor but not vice versa.We show that the spectral radius of a strictly nonnegative tensor is always positive.We give some necessary and su?cient conditions for the six wellconditional classes of nonnegative tensors,introduced in the literature,and a full relationship picture about strictly nonnegative tensors with these six classes of nonnegative tensors.We then establish global R-linear convergence of a power method for finding the spectral radius of a nonnegative tensor under the condition of weak irreducibility.We show that for a nonnegative tensor T,there always exists a partition of the index set such that every tensor induced by the partition is weakly irreducible;and the spectral radius of T can be obtained from those spectral radii of the induced tensors.In this way,we develop a convergent algorithm for finding the spectral radius of a general nonnegative tensor without any additional assumption.Some preliminary numerical results show the feasibility and effectiveness of the algorithm.

  1. Inversion of hematocrit partition at microfluidic bifurcations

    CERN Document Server

    Shen, Zaiyi; Kaoui, Badr; Polack, Benoît; Harting, Jens; Misbah, Chaouqi; Podgorski, Thomas

    2016-01-01

    Partitioning of red blood cells (RBCs) at the level of bifurcations in the microcirculatory system affects many physiological functions yet it remains poorly understood. We address this problem by using T-shaped microfluidic bifurcations as a model. Our computer simulations and in vitro experiments reveal that the hematocrit ($\\phi_0$) partition depends strongly on RBC deformability, as long as $\\phi_0 <20$% (within the normal range in microcirculation), and can even lead to complete deprivation of RBCs in a child branch. Furthermore, we discover a deviation from the Zweifach-Fung effect which states that the child branch with lower flow rate recruits less RBCs than the higher flow rate child branch. At small enough $\\phi_0$, we get the inverse scenario, and the hematocrit in the lower flow rate child branch is even higher than in the parent vessel. We explain this result by an intricate up-stream RBC organization and we highlight the extreme dependence of RBC transport on geometrical and cell mechanical p...

  2. New parallel SOR method by domain partitioning

    Energy Technology Data Exchange (ETDEWEB)

    Xie, Dexuan [Courant Inst. of Mathematical Sciences New York Univ., NY (United States)

    1996-12-31

    In this paper, we propose and analyze a new parallel SOR method, the PSOR method, formulated by using domain partitioning together with an interprocessor data-communication technique. For the 5-point approximation to the Poisson equation on a square, we show that the ordering of the PSOR based on the strip partition leads to a consistently ordered matrix, and hence the PSOR and the SOR using the row-wise ordering have the same convergence rate. However, in general, the ordering used in PSOR may not be {open_quote}consistently ordered{close_quotes}. So, there is a need to analyze the convergence of PSOR directly. In this paper, we present a PSOR theory, and show that the PSOR method can have the same asymptotic rate of convergence as the corresponding sequential SOR method for a wide class of linear systems in which the matrix is {open_quotes}consistently ordered{close_quotes}. Finally, we demonstrate the parallel performance of the PSOR method on four different message passing multiprocessors (a KSR1, the Intel Delta, an Intel Paragon and an IBM SP2), along with a comparison with the point Red-Black and four-color SOR methods.

  3. Gait Partitioning Methods: A Systematic Review

    Directory of Open Access Journals (Sweden)

    Juri Taborri

    2016-01-01

    Full Text Available In the last years, gait phase partitioning has come to be a challenging research topic due to its impact on several applications related to gait technologies. A variety of sensors can be used to feed algorithms for gait phase partitioning, mainly classifiable as wearable or non-wearable. Among wearable sensors, footswitches or foot pressure insoles are generally considered as the gold standard; however, to overcome some inherent limitations of the former, inertial measurement units have become popular in recent decades. Valuable results have been achieved also though electromyography, electroneurography, and ultrasonic sensors. Non-wearable sensors, such as opto-electronic systems along with force platforms, remain the most accurate system to perform gait analysis in an indoor environment. In the present paper we identify, select, and categorize the available methodologies for gait phase detection, analyzing advantages and disadvantages of each solution. Finally, we comparatively examine the obtainable gait phase granularities, the usable computational methodologies and the optimal sensor placements on the targeted body segments.

  4. Approximation Algorithms for Submodular Multiway Partition

    CERN Document Server

    Chekuri, Chandra

    2011-01-01

    We study algorithms for the Submodular Multiway Partition problem (SubMP). An instance of SubMP consists of a finite ground set $V$, a subset of $k$ elements $S = \\{s_1,s_2,...,s_k\\}$ called terminals, and a non-negative submodular set function $f:2^V\\rightarrow \\mathbb{R}_+$ on $V$ provided as a value oracle. The goal is to partition $V$ into $k$ sets $A_1,...,A_k$ such that for $1 \\le i \\le k$, $s_i \\in A_i$ and $\\sum_{i=1}^k f(A_i)$ is minimized. SubMP generalizes some well-known problems such as the Multiway Cut problem in graphs and hypergraphs, and the Node-weighed Multiway Cut problem in graphs. SubMP for arbitrarysubmodular functions (instead of just symmetric functions) was considered by Zhao, Nagamochi and Ibaraki \\cite{ZhaoNI05}. Previous algorithms were based on greedy splitting and divide and conquer strategies. In very recent work \\cite{ChekuriE11} we proposed a convex-programming relaxation for SubMP based on the Lov\\'asz-extension of a submodular function and showed its applicability for some ...

  5. The potential of centrifugal casting for the production of near net shape uranium parts

    Energy Technology Data Exchange (ETDEWEB)

    Robertson, E. [United States Air Force Academy, Colorado Springs, CO (US). Dept. of Engineering Mechanics

    1993-09-01

    This report was written to provide a detailed summary of a literature survey on the near net shape casting process of centrifugal casting. Centrifugal casting is one potential casting method which could satisfy the requirements of the LANL program titled Near Net Shape Casting of Uranium for Reduced Environmental, Safety and Health Impact. In this report, centrifugal casting techniques are reviewed and an assessment of the ability to achieve the near net shape and waste minimization goals of the LANL program by using these techniques is made. Based upon the literature reviewed, it is concluded that if properly modified for operation within a vacuum, vertical or horizontal centrifugation could be used to safely cast uranium for the production of hollow, cylindrical parts. However, for the production of components of geometries other than hollow tubes, vertical centrifugation could be combined with other casting methods such as semi-permanent mold or investment casting.

  6. S^3/Z_n partition function and dualities

    CERN Document Server

    Imamura, Yosuke

    2012-01-01

    We investigate S^3/Z_n partition function of N = 2 supersymmetric gauge theories. A gauge theory on the orbifold has degenerate vacua specified by the holonomy. The partition function is obtained by summing up the contributions of saddle points with different holonomies. An appropriate choice of the phase of each contribution is essential to obtain the partition function. We determine the relative phases in the holonomy sum in a few examples by using duality to non-gauge theories. In the case of odd n the phase factors can be absorbed by modifying a single function appearing in the partition function.

  7. Molecular partitioning based on the kinetic energy density

    Science.gov (United States)

    Noorizadeh, Siamak

    2016-05-01

    Molecular partitioning based on the kinetic energy density is performed to a number of chemical species, which show non-nuclear attractors (NNA) in their gradient maps of the electron density. It is found that NNAs are removed using this molecular partitioning and although the virial theorem is not valid for all of the basins obtained in the being used AIM, all of the atoms obtained using the new approach obey this theorem. A comparison is also made between some atomic topological parameters which are obtained from the new partitioning approach and those calculated based on the electron density partitioning.

  8. Aspects of system modelling in Hardware/Software partitioning

    DEFF Research Database (Denmark)

    Knudsen, Peter Voigt; Madsen, Jan

    1996-01-01

    This paper addresses fundamental aspects of system modelling and partitioning algorithms in the area of Hardware/Software Codesign. Three basic system models for partitioning are presented and the consequences of partitioning according to each of these are analyzed. The analysis shows...... the importance of making a clear distinction between the model used for partitioning and the model used for evaluation It also illustrates the importance of having a realistic hardware model such that hardware sharing can be taken into account. Finally, the importance of integrating scheduling and allocation...

  9. A Comparison of delO18 Composition of Water Extracted from Suction Lysimeters, Centrifugation, and Azeotropic Distillation

    Science.gov (United States)

    Figueroa, A.; Tindall, J. A.; Friedel, M. J.

    2005-12-01

    Concentration of delO18 in water samples extracted by suction lysimeters is compared to samples obtained by methods of centrifugation and azeotropic distillation. Intact soil cores (30 cm diameter by 40 cm height) were extracted from two different sites. Site 1 was rapid infiltration basin number 50, near Altamonte Springs in Seminole County, Florida on properties belonging to the Walt Disney World Resort Complex. Site 2 was the Missouri Management System Evaluation Area (MSEA) near Centralia in Boone County, Missouri. The delO18 water was analyzed on a mass spectrophotometer. Potassium Bromide (KBr) was also used as a tracer and analyzed by ion chromatography. A portion of the data obtained was modeled using CXTFIT. Water collected by centrifugation and azeotropic distillation data were about 2-5% more negative than that collected by suction lysimeter values from the Florida (sandy) soil and about 5-7 % more negative from the Missouri (well structured clay) soil. Results indicate that the majority of soil water in well structured soil is strongly bound to soil grain surfaces and is not easily sampled by suction lysimeters. Also, it is plausible that evaporation caused some delO18 enrichment in the suction lysimeters. Suction lysimeters preferentially sampled water held at lower matric potentials, which may not represent total soil water. In cases where a sufficient volume of water has passed through the soil profile and displaced all previous pore water, suction lysimeters will however collect a representative sample of all the water at that depth interval. It is suggested that for stable isotope studies monitoring precipitation and soil water, suction lysimeters be installed at shallow depths (10 cm). Samples should also be coordinated with precipitation events. The CXTFIT program worked well for Florida soils (a more homogeneous sand), but gave poor performance for Missouri soils (well structured clays) except for deeper depths where clay structure was less

  10. Influence of ripening stages of tomatoes in the analysis of pesticides by gas chromatography

    OpenAIRE

    Sousa,Flaviane A. de; Neves,Antônio A.; Maria Eliana L. R. Queiroz; Heleno,Fernanda F.; Teófilo, Reinaldo F.; Pinho,Gevany P.

    2014-01-01

    Some parameters of tomato fruits ripening such as color, pH, ºBrix, acidity and lycopene and β-carotene content were evaluated during the ripening of fruits. Five pesticides were quantified in organic extracts derived from tomatoes at different stages of maturation. The solid-liquid extraction technique with partition at low temperature (SLE-PLT) was used to obtain these organic extracts. The matrix effect of tomato was calculated from the results of analysis by gas chromatography with e...

  11. Partitioning planning studies: Preliminary evaluation of metal and radionuclide partitioning the high-temperature thermal treatment systems

    Energy Technology Data Exchange (ETDEWEB)

    Liekhus, K.; Grandy, J.; Chambers, A. [and others

    1997-03-01

    A preliminary study of toxic metals and radionuclide partitioning during high-temperature processing of mixed waste has been conducted during Fiscal Year 1996 within the Environmental Management Technology Evaluation Project. The study included: (a) identification of relevant partitioning mechanisms that cause feed material to be distributed between the solid, molten, and gas phases within a thermal treatment system; (b) evaluations of existing test data from applicable demonstration test programs as a means to identify and understand elemental and species partitioning; and, (c) evaluation of theoretical or empirical partitioning models for use in predicting elemental or species partitioning in a thermal treatment system. This preliminary study was conducted to identify the need for and the viability of developing the tools capable of describing and predicting toxic metals and radionuclide partitioning in the most applicable mixed waste thermal treatment processes. This document presents the results and recommendations resulting from this study that may serve as an impetus for developing and implementing these predictive tools.

  12. Numerical study of a high-speed miniature centrifugal compressor

    Science.gov (United States)

    Li, Xiaoyi

    A miniature centrifugal compressor is a key component of reverse Brayton cycle cryogenic cooling system. The system is commonly used to generate a low cryogenic temperature environment for electronics to increase their efficiency, or generate, store and transport cryogenic liquids, such as liquid hydrogen and oxygen, where space limit is also an issue. Because of space limitation, the compressor is composed of a radial IGV, a radial impeller and an axial-direction diffuser (which reduces the radial size because of smaller diameter). As a result of reduction in size, rotating speed of the impeller is as high as 313,000 rpm, and Helium is used as the working fluid, in order to obtain the required static pressure ratio/rise. Two main characteristics of the compressor---miniature and high-speed, make it distinct from conventional compressors. Higher compressor efficiency is required to obtain a higher COP (coefficient of performance) system. Even though miniature centrifugal compressors start to draw researchers' attention in recent years, understanding of the performance and loss mechanism is still lacking. Since current experimental techniques are not advanced enough to capture details of flow at miniature scale, numerical methods dominate miniature turbomachinery study. This work numerically studied a high speed miniature centrifugal compressor with commercial CFD code. The overall performance of the compressor was predicted with consideration of interaction between blade rows by using sliding mesh model. The law of similarity of turbomachinery was validated for small scale machines. It was found that the specific ratio effect needs to be considered when similarity law is applied. But Reynolds number effect can be neglected. The loss mechanism of each component was analyzed. Loss due to turning bend was significant in each component. Tip leakage loss of small scale turbomachines has more impact on the impeller performance than that of large scale ones. Because the

  13. Use of partially shrouded impeller in a small centrifugal compressor

    Institute of Scientific and Technical Information of China (English)

    Jin Tang; Teemu Turunen-Saaresti; Jaakko Larjola

    2008-01-01

    Numerical analysis is conducted for the 3-dimensional impeller and vaneless diffuser of a small centrifugal compressor. The influence of impeller tip clearance on the flow field of the impeller is investigated. Detailed investigation on the leaking flow across the tip clearance of the impeller shows that the leaking flow rate is higher near the exit of the impeller than that near the inlet of the impeller. Based on this phenomenon, a new partially shrouded impeller is designed. The impeller is shrouded near the exit of the impeller. Numerical results show that the secondary flow region becomes smaller at the exit of the impeller. Better performance is achieved than that with the unshrouded impeller.

  14. Approaches to stable operation of shaftless centrifugal pump

    Science.gov (United States)

    Kawashima, Ryunosuke; Uno, Mitsuo; Kanemoto, Toshiaki

    2009-03-01

    The shaft-less impeller of the centrifugal pump, which is driven by the magnetic induction, was developed. The impeller rotates under the floating condition without any control device. The floating condition of the impeller is realized by utilizing the pressure in pump casing. The pump performance and the rotational behavior of the impeller were investigated experimentally. It has found that the floating position of the impeller become quite unstable in a partial flow rate operation. And the pressure distribution at the casing wall affects the rotational posture of the impeller. This paper presents the effect of the casing treatment on the rotational posture of the impeller and the pressure distribution. The reasonable casing treatment is available for the stable rotational posture of the impeller.

  15. Centrifugal photovoltaic and photogalvanic effects driven by structured light

    CERN Document Server

    Wätzel, Jonas

    2016-01-01

    Much efforts are devoted to material structuring in a quest to enhance the photovoltaic effect. We show that structuring light in a way it transfers orbital angular momentum to semiconductor-based rings results in a steady charge accumulation at the outer boundaries that be utilized for the generation of an open circuit voltage or a photogalvanic (bulk photovoltaic) type current. This effect which stems both from structuring light and matter (confinement potentials), can be magnified even at fixed moderate intensities, by increasing the orbital angular momentum of light which strengthens the effective centrifugal potential that repels the charge outwards. Based on a full numerical time propagation of the carriers wave functions in the presence of light pulses we demonstrate how the charge buildup leads to a useable voltage or directed photocurrent whose amplitudes and directions are controllable by the light pulse parameters.

  16. Centrifugal experimental study of suction bucket foundations under dynamic loading

    Institute of Scientific and Technical Information of China (English)

    Xiaobing Lu; Yongren Wu; Bintian Jiao; Shuyun Wang

    2007-01-01

    Centrifugal experiments were carded out to investigate the responses of suction bucket foundations under horizontal and vertical dynamic loading. It is shown that when the loading amplitude is over a critical value, the sand at the upper part around the bucket is softened or even liq-uefied. The excess pore pressure decreases from the upper part to the lower part of the sand layer in the vertical direc-tion and decreases radially from the bucket's side wall in the horizontal direction. Large settlements of the bucket and the sand layer around the bucket are induced by dynamic load-ing. The dynamic responses of the bucket with smaller height (the same diameter) are heavier.

  17. Effect of Fluid Viscosity on Centrifugal Pump Performance

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Nohhyeong [GS Caltex Corporation, Daejeon (Korea, Republic of)

    2013-06-15

    The characteristics of centrifugal pump performance according to fluid viscosity change were studied experimentally. A small volute pump with low specific speed was tested by changing the viscosity of an aqueous solution of sugar and glycerin, which is considered a Newtonian fluid. After finishing the test, the total head, shaft horsepower, and pump efficiency were compared with those of a water pump. The results are summarized as follows: when the fluid viscosity is increased, the shut-off head shows very little change but the total head decreases gradually as the flow increases, and this makes the H-Q curve leaning rapidly, and when the fluid viscosity is increased, the shaft horsepower shows very little change at the shutoff condition; however, the shaft horsepower increases more rapidly with an increase in the flow and viscosity.

  18. Stopping intense beams of internally cold molecules via centrifugal forces

    Science.gov (United States)

    Wu, Xing; Gantner, Thomas; Zeppenfeld, Martin; Chervenkov, Sotir; Rempe, Gerhard

    2016-05-01

    Cryogenic buffer-gas cooling produces intense beams of internally cold molecules. It offers a versatile source for studying collision dynamics and reaction pathways in the cold regime, and could open new avenues for controlled chemistry, precision spectroscopy, and exploration of fundamental physics. However, an efficient deceleration of these beams still presents a challenge. Here, we demonstrate that intense and continuous beams of electrically guided molecules produced by a cryogenic buffer-gas cell can be brought to a halt by the centrifugal force in a rotating frame. Various molecules (e.g. CH3F and CF3CCH) are decelerated to below 20m /s at a corresponding output intensity of ~ 6 ×109mm-2 .s-1 . In addition, our RF-resonant depletion detection shows that up to 90 % rotational-state purity can be achieved in the so-produced slow molecular beams.

  19. Centrifugal photovoltaic and photogalvanic effects driven by structured light.

    Science.gov (United States)

    Wätzel, J; Berakdar, J

    2016-02-22

    Much efforts are devoted to material structuring in a quest to enhance the photovoltaic effect. We show that structuring light in a way it transfers orbital angular momentum to semiconductor-based rings results in a steady charge accumulation at the outer boundaries that can be utilized for the generation of an open circuit voltage or a photogalvanic (bulk photovoltaic) type current. This effect which stems both from structuring light and matter confinement potentials, can be magnified even at fixed moderate intensities, by increasing the orbital angular momentum of light which strengthens the effective centrifugal potential that repels the charge outwards. Based on a full numerical time propagation of the carriers wave functions in the presence of light pulses we demonstrate how the charge buildup leads to a useable voltage or directed photocurrent whose amplitudes and directions are controllable by the light pulse parameters.

  20. Ultrasound treatment of centrifugally atomized 316 stainless steel powders

    Science.gov (United States)

    Rawers, James C.; McCune, Robert A.; Dunning, John S.

    1991-12-01

    The Bureau of Mines is studying the surface characteristics of rapidly solidified powders and the potential for surface modification of fine powders prior to consolidation. The surface modification and work hardening of fine powders were accomplished by applying high-energy ultrasound to centrifugally atomized austenitic 316 stainless steel powders suspended in liquid media. Cavitation implosion changed the surface morphology, hammering the surface and occasionally fretting off microchips of work-hardened metal. Ultrasound-cavitation work-hardened metal powder surfaces producing a strained, duplex austenite face-centered cubic (fcc)-martensite body-centered tetragonal (bct) phase structure. The amount of work hardening depended upon the quantity of ultrasound energy used, considering both power level and experimental time. Work hardening was relatively independent of the liquid media used.